Effects of seasonal climatic variability on several toxic contaminants in urban lakes: Implications for the impacts of climate change.

PubMed

Wu, Qiong; Xia, Xinghui; Mou, Xinli; Zhu, Baotong; Zhao, Pujun; Dong, Haiyang

2014-12-01

Climate change is supposed to have influences on water quality and ecosystem. However, only few studies have assessed the effect of climate change on environmental toxic contaminants in urban lakes. In this research, response of several toxic contaminants in twelve urban lakes in Beijing, China, to the seasonal variations in climatic factors was studied. Fluorides, volatile phenols, arsenic, selenium, and other water quality parameters were analyzed monthly from 2009 to 2012. Multivariate statistical methods including principle component analysis, cluster analysis, and multiple regression analysis were performed to study the relationship between contaminants and climatic factors including temperature, precipitation, wind speed, and sunshine duration. Fluoride and arsenic concentrations in most urban lakes exhibited a significant positive correlation with temperature/precipitation, which is mainly caused by rainfall induced diffuse pollution. A negative correlation was observed between volatile phenols and temperature/precipitation, and this could be explained by their enhanced volatilization and biodegradation rates caused by higher temperature. Selenium did not show a significant response to climatic factor variations, which was attributed to low selenium contents in the lakes and soils. Moreover, the response degrees of contaminants to climatic variations differ among lakes with different contamination levels. On average, temperature/precipitation contributed to 8%, 15%, and 12% of the variations in volatile phenols, arsenic, and fluorides, respectively. Beijing is undergoing increased temperature and heavy rainfall frequency during the past five decades. This study suggests that water quality related to fluoride and arsenic concentrations of most urban lakes in Beijing is becoming worse under this climate change trend. Copyright © 2014. Published by Elsevier B.V.

New insights into the mechanism of methoxyflurane nephrotoxicity and implications for anesthetic development (part 1): Identification of the nephrotoxic metabolic pathway.

PubMed

Kharasch, Evan D; Schroeder, Jesara L; Liggitt, H Denny; Park, Sang B; Whittington, Dale; Sheffels, Pamela

2006-10-01

Methoxyflurane nephrotoxicity results from biotransformation; inorganic fluoride is a toxic metabolite. Concern exists about potential renal toxicity from volatile anesthetic defluorination, but many anesthetics increase fluoride concentrations without consequence. Methoxyflurane is metabolized by both dechlorination to methoxydifluoroacetic acid (MDFA, which may degrade to fluoride) and O-demethylation to fluoride and dichloroacetatic acid. The metabolic pathway responsible for methoxyflurane nephrotoxicity has not, however, been identified, which was the aim of this investigation. Experiments evaluated methoxyflurane metabolite formation and effects of enzyme induction or inhibition on methoxyflurane metabolism and toxicity. Rats pretreated with phenobarbital, barium sulfate, or nothing were anesthetized with methoxyflurane, and renal function and urine methoxyflurane metabolite excretion were assessed. Phenobarbital effects on MDFA metabolism and toxicity in vivo were also assessed. Metabolism of methoxyflurane and MDFA in microsomes from livers of pretreated rats was determined in vitro. Phenobarbital pretreatment increased methoxyflurane nephrotoxicity in vivo (increased diuresis and blood urea nitrogen and decreased urine osmolality) and induced in vitro hepatic microsomal methoxyflurane metabolism to inorganic fluoride (2-fold), dichloroacetatic acid (1.5-fold), and MDFA (5-fold). In contrast, phenobarbital had no influence on MDFA renal effects in vivo or MDFA metabolism in vitro or in vivo. MDFA was neither metabolized to fluoride nor nephrotoxic. Barium sulfate diminished methoxyflurane metabolism and nephrotoxicity in vivo. Fluoride from methoxyflurane anesthesia derives from O-demethylation. Phenobarbital increases in methoxyflurane toxicity do not seem attributable to methoxyflurane dechlorination, MDFA toxicity, or MDFA metabolism to another toxic metabolite, suggesting that nephrotoxicity is attributable to methoxyflurane O-demethylation. Fluoride, one of many metabolites from O-demethylation, may be toxic and/or reflect formation of a different toxic metabolite. These results may have implications for interpreting anesthetic defluorination, volatile anesthetic use, and methods to evaluate anesthetic toxicity.

PILOT-SCALE REMOVAL OF FLUORIDE FROM LEGACY PLUTONIUM MATERIALS USING VACUUM SALT DISTILLATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R. A.; Pak, D. J.

2012-09-11

Between September 2009 and January 2011, the Savannah River National Laboratory (SRNL) and HB-Line designed, developed, tested, and successfully deployed a system for the distillation of chloride salts. In 2011, SRNL adapted the technology for the removal of fluoride from fluoride-bearing salts. The method involved an in situ reaction between potassium hydroxide (KOH) and the fluoride salt to yield potassium fluoride (KF) and the corresponding oxide. The KF and excess KOH can be distilled below 1000{deg}C using vacuum salt distillation (VSD). The apparatus for vacuum distillation contains a zone heated by a furnace and a zone actively cooled using eithermore » recirculated water or compressed air. During a vacuum distillation operation, a sample boat containing the feed material is placed into the apparatus while it is cool, and the system is sealed. The system is evacuated using a vacuum pump. Once a sufficient vacuum is attaned, heating begins. Volatile salts distill from the heated zone to the cooled zone where they condense, leaving behind the non-volatile material in the feed boat. Studies discussed in this report were performed involving the use of non-radioactive simulants in small-scale and pilot-scale systems as well as radioactive testing of a small-scale system with plutonium-bearing materials. Aspects of interest include removable liner design considerations, boat materials, in-line moisture absorption, and salt deposition.« less

FLUORIDE VOLATILITY PROCESS FOR THE RECOVERY OF URANIUM

DOEpatents

Katz, J.J.; Hyman, H.H.; Sheft, I.

1958-04-15

The separation and recovery of uraniunn from contaminants introduced by neutron irradiation by a halogenation and volatilization method are described. The irradiated uranium is dissolved in bromine trifluoride in the liquid phase. The uranium is converted to the BrF/sub 3/ soluble urmium hexafluoride compound whereas the fluorides of certain contaminating elements are insoluble in liquid BrF/sub 3/, and the reaction rate of the BrF/sub 3/ with certain other solid uranium contamirnnts is sufficiently slower than the reaction rate with uranium that substantial portions of these contaminating elements will remain as solids. These solids are then separated from the solution by a distillation, filtration, or centrifugation step. The uranium hexafluoride is then separated from the balance of the impurities and solvent by one or more distillations.

Image Information Obtained Using a Charge-Coupled Device (CCD) Camera During an Immersion Liquid Evaporation Process for Measuring the Refractive Index of Solid Particles.

PubMed

Niskanen, Ilpo; Sutinen, Veijo; Thungström, Göran; Räty, Jukka

2018-06-01

The refractive index is a fundamental physical property of a medium, which can be used for the identification and purity issues of all media. Here we describe a refractive index measurement technique to determine simultaneously the refractive index of different solid particles by monitoring the transmittance of light from a suspension using a charge-coupled device (CCD) camera. An important feature of the measurement is the liquid evaporation process for the refractive index matching of the solid particle and the immersion liquid; this was realized by using a pair of volatile and non-volatile immersion liquids. In this study, refractive indices of calcium fluoride (CaF 2 ) and barium fluoride (BaF 2 ) were determined using the proposed method.

Study of fluoride corrosion of nickel alloys

NASA Technical Reports Server (NTRS)

Gunther, W. H.; Steindler, M. J.

1969-01-01

Report contains the results of an investigation of the corrosion resistance of nickel and nickel alloys exposed to fluorine, uranium hexafluoride, and volatile fission product fluorides at high temperatures. Survey of the unclassified literature on the subject is included.

FY90 R&D Project Descriptions ESL (Engineering & Services Laboratory) Environics Division

DTIC Science & Technology

1989-07-01

and Development Support for Subsurface Monitoring Technology 15 19007048 Pumping and Purging Contaminants 16 19007049 Methods for Selecting In Situ...Decontamination 40 3788VW17 Treatment of Chlorinated Organics with Aboveground Bioreactors 41 3788VW18 Improved Methods for Monitoring Fuel Biodegradation 42 2...Fluoride (HF) Dispersion Model 63 21036093 Solvent Capacity Field Test Method 64 21037097 Volatile Organic Compound (VOC) Control Technology 65 21037102

CHEMICAL ENGINEERING DIVISION SUMMARY REPORT, OCTOBER, NOVEMBER, DECEMBER 1960

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1961-03-01

Chemical-metallurgical processing studies were made of pyrometallurgical development snd research, and fuel processing facilities for EBR-II. Fuel-cycle applications of fluidization and volatility techniques included laboratory investigations of fluoride volatility processes, engineeringscale development, and conversion of UF/sub 6/ to UO/sub 2/. Reactor safety studies consisted of metal oxidation and ignition kinetics, and metal-water reactions. Reactor chemistry investigations were conducted to determine nuclear constants and suitable reactor decontamination methods. Routine operations are summarized for the high-level gammairradiation facillty and waste processing. (B.O.G.)

Method of repressing the precipitation of calcium fluozirconate

DOEpatents

Newby, B.J.; Rhodes, D.W.

1973-12-25

Boric acid or a borate salt is added to aqueous solutions of fluoride containing radioactive wastes generated during the reprocessing of zirconium alloy nuclear fuels which are to be converted to solid form by calcining in a fluidized bed. The addition of calcium nitrate to the aqueous waste solutions to prevent fluoride volatility during calcination, causes the precipitation of calcium fluozirconate, which tends to form a gel at fluoride concentrations of 3.0 M or greater. The boron containing species introduced into the solution by the addition of the boric acid or borate salt retard the formation of the calcium fluozirconate precipitate and prevent formation of the gel. These boron containing species can be introduced into the solution by the addition of a borate salt but preferably are introduced by the addition of an aqueous solution of boric acid. (Official Gazette)

Symposium on the reprocessing of irradiated fuels. Book 2, Session IV

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1958-12-31

Book two of this conference has a single-focused session IV entitled Nonaqueous Processing, with 8 papers. The session deals with fluoride volatility processes and pyrometallurgical or pyrochemical processes. The latter involves either an oxide drossing or molten metal extraction or fused salt extraction technique and results in only partial decontamination. Fluoride volatility processes appear to be especially favorable for recovery of enriched uranium and decontamination factors of 10/sup 7/ to 10/sup 8/ would be achieved by simpler means than those employed in solvent extraction. Data from lab research on the BrF/sub 3/ process and the ClF/sub 3/ process are givenmore » and discussed and pilot plant experience is described, all in connection with natural uranium or slightly enriched uranium processing. Fluoride volatility processes for enriched or high alloy fuels are described step by step. The economic and engineering considerations of both types of nonaqueous processing are treated separately and as fully as present knowledge allows. A comprehensive review of the chemistry of pyrometallurgical processes is included.« less

Selective Fluorination and Separation of Metals with NF3 for Mass Spectrometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, Richard A.; Barinaga, Charles J.; McNamara, Bruce K.

2016-03-01

We report recent progress on the development of a new methodology based on the generation of volatile metal fluorides through the use of nitrogen trifluoride (NF3), and the separation and measurement of these metal fluorides by electron ionization mass spectrometry. Though unreactive under ambient conditions, NF3 reacts selectively at specified temperatures with various metal-containing species to form volatile metal fluorides. Utilizing these species-dependent traits, elements of a sample may be sequentially produced and thus separated on-line. Metals were reacted inside a thermogravimetric analyzer, the gas outlet of which was directly coupled to a quadrupole mass spectrometer with an electron impactmore » ionization source via a molecular leak valve. We present results of this project including the electron ionization mass spectrum of gaseous tellurium hexafluoride.« less

78 FR 37973 - Change of Address for Region 7; Technical Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-25

... recordkeeping requirements, Sulfur oxides, Volatile organic compounds. 40 CFR Part 59 Environmental protection... requirements, Volatile organic compounds. 40 CFR Part 60 Environmental protection, Administrative practice and..., Cement industry, Chemicals, Coal, Copper, Dry cleaners, Electric power plants, Fertilizers, Fluoride...

URANIUM RECOVERY FROM COMPOSITE UF$sub 4$ REDUCTION BOMB WASTES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, E R; Doyle, R L; Coleman, J R

1954-01-28

A number of techniques have been investigated on a laboratory-scale for separating uranium from fluorides during the recovery of uranium from UF4 reduction bomb wastes (C-oxide) by an HCl leach - NH4OH precipitation process. Among these are included adsorption of fluorides from filtered leach liquors, fractional precipitation of fluorides and uranium, complexing of fluorides into forms soluble in slightly acid solutions, and fluoride volatilization from the uranium concentrate. Solubility studies of CaF2 and MgF2 in aqueous hydrochloric acid at various acidities and temperatures were also conducted. A description of the production-scale processing of C-oxide in the FMPC scrap plant hasmore » been included.« less

APPLICATION OF VACUUM SALT DISTILLATION TECHNOLOGY FOR THE REMOVAL OF FLUORIDE AND CHLORIDE FROM LEGACY FISSILE MATERIALS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.; Peters, T.

2011-11-01

Between September 2009 and January 2011, the Savannah River National Laboratory (SRNL) and the Savannah River Site (SRS) HB-Line Facility designed, developed, tested, and successfully deployed a production-scale system for the distillation of sodium chloride (NaCl) and potassium chloride (KCl) from plutonium oxide (PuO{sub 2}). Subsequent efforts adapted the vacuum salt distillation (VSD) technology for the removal of chloride and fluoride from less-volatile halide salts at the same process temperature and vacuum. Calcium chloride (CaCl{sub 2}), calcium fluoride (CaF{sub 2}), and plutonium fluoride (PuF{sub 3}) were of particular concern. To enable the use of the same operating conditions for themore » distillation process, SRNL employed in situ exchange reactions to convert the less-volatile halide salts to compounds that facilitated the distillation of halide without removal of plutonium. SRNL demonstrated the removal of halide from CaCl{sub 2}, CaF{sub 2} and PuF{sub 3} below 1000 C using VSD technology.« less

Molecular emission characteristics of various fluorides in a low-temperature-hydrogen diffusion flame.

PubMed

Dagnall, R M; Fleet, B; Risby, T H; Deans, D R

1971-02-01

A capillary burner supporting a nitrogen/hydrogen diffusion flame has been evaluated as a possible means of detection for several volatile fluorides after their gas-chromatographic separation. The fluorides of As, B, C, Ge, I, Mo, P, Re, S, Sb, Se, Si, Te and W were formed by the reaction of the element with chlorine trifluoride, and the intense molecular emission given by each was recorded. An attempt was made to identify the emitting species.

Comparison of storage stability of odorous VOCs in polyester aluminum and polyvinyl fluoride tedlar bags

USDA-ARS?s Scientific Manuscript database

Whole air sampling using containers such as flexible bags or rigid canisters is commonly used to collect samples of volatile organic compounds (VOC) in air. The objective of this study was to compare the stability of polyester aluminum (PEA) and polyvinyl fluoride (PVF, brand name Tedlar®) bags for ...

Effects of deuteration on the metabolism of halogenated anesthetics in the rat

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCarty, L.P.; Malek, R.S.; Larsen, E.R.

1979-08-01

The authors studied the effects of substituting deuterium for hydrogen in several volatile anesthetics on their metabolism in the Fischer rat. Substitution of deuterium in the ethyl portion of methoxyflurane increased the metabolic production of fluoride ion by 19 percent when administered at a concentration of 0.05%. Total replacement of hydrogen by deuterium resulted in a 29% decrease in the amount of fluoride produced, while deuteration of only the methoxyl group produced a 33% decrease in fluoride produced. Deuteration of halothane resulted in a 15 or 26% decrease in serum bromide at 0.75% or 1.0%, respectively. Deuteration in the ethylmore » portions of enflurane and two experimental agents, CF2HOCF2CFBrH and CF2HOCF2CCl2H resulted in 65, 76, and 29% decreases in urinary fluoride, respectively. Anesthesia with deuterated chloroform at a concentration of 0.36% produced a 35% decrease in serum glutamic pyruvic transaminase (SGPT). It is concluded that deuteration of volatile anesthetics changes their metabolism, in most cases producing decreases in metabolism. This effect may lessen the organ toxicity believed to occur with some of these anesthetics.« less

APPLICATION OF VACUUM SALT DISTILLATION TECHNOLOGY FOR THE REMOVAL OF FLUORIDE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.; Pak, D.

2011-08-10

Vacuum distillation of chloride salts from plutonium oxide (PuO{sub 2}) and simulant PuO{sub 2} has been previously demonstrated at Department of Energy (DOE) sites using kilogram quantities of chloride salt. The apparatus for vacuum distillation contains a zone heated using a furnace and a zone actively cooled using either recirculated water or compressed air. During a vacuum distillation operation, a sample boat containing the feed material is placed into the apparatus while it is cool, and the system is sealed. The system is evacuated using a vacuum pump. Once a sufficient vacuum is attained, heating begins. Volatile salts distill frommore » the heated zone to the cooled zone where they condense, leaving behind the non-volatile materials in the feed boat. The application of vacuum salt distillation (VSD) is of interest to the HB-Line Facility and the MOX Fuel Fabrication Facility (MFFF) at the Savannah River Site (SRS). Both facilities are involved in efforts to disposition excess fissile materials. Many of these materials contain chloride and fluoride salt concentrations which make them unsuitable for dissolution without prior removal of the chloride and fluoride salts. Between September 2009 and January 2011, the Savannah River National Laboratory (SRNL) and HB-Line designed, developed, tested, and successfully deployed a system for the distillation of chloride salts. Subsequent efforts are attempting to adapt the technology for the removal of fluoride. Fluoride salts of interest are less-volatile than the corresponding chloride salts. Consequently, an alternate approach is required for the removal of fluoride without significantly increasing the operating temperature. HB-Line Engineering requested SRNL to evaluate and demonstrate the feasibility of an alternate approach using both non-radioactive simulants and plutonium-bearing materials. Whereas the earlier developments targeted the removal of sodium chloride (NaCl) and potassium chloride (KCl), the current activities are concerned with the removal of the halide ions associated with plutonium trifluoride (PuF{sub 3}), plutonium tetrafluoride (PuF{sub 4}), calcium fluoride (CaF{sub 2}), and calcium chloride (CaCl{sub 2}). This report discusses non-radioactive testing of small-scale and pilot-scale systems and radioactive testing of a small-scale system. Experiments focused on demonstrating the chemistry for halide removal and addressing the primary engineering questions associated with a change in the process chemistry.« less

PLATINUM HEXAFLUORIDE AND METHOD OF FLUORINATING PLUTONIUM CONTAINING MIXTURES THERE-WITH

DOEpatents

Malm, J.G.; Weinstock, B.; Claassen, H.H.

1959-07-01

The preparation of platinum hexafluoride and its use as a fluorinating agent in a process for separating plutonium from fission products is presented. According to the invention, platinum is reacted with fluorine gas at from 900 to 1100 deg C to form platinum hexafluoride. The platinum hexafluoride is then contacted with the plutonium containing mixture at room temperature to form plutonium hexafluoride which is more volatile than the fission products fluorides and therefore can be isolated by distillation.

QUANTITATIVE RADIO-CHEMICAL ANALYSIS-SOLVENT EXTRACTION OF MOLYBDENUM-99

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wish, L.

1961-09-12

A method was developed for the rapid quantitative separation of Mo/sup 99/ from fission product mixtures. It is based on the extraction of Mo into a solution of alpha -benzoin oxime in chloroform. The main contaminants are Zr, Nb, and 1. The first two are eliminated by couple with fluoride and the third by volatilization or solvent extraction. About 5% of the Te/sup 99/ daughter is extracted with its parent, and it is necessary to wait 48 hrs for equilibrium of fission product mixtures by this method and a standard radiochemical gravimetric procedure showed agreement within 1 to 2%. (auth)

Separation of metallic residues from the dissolution of a high-burnup BWR fuel using nitrogen trifluoride

DOE Office of Scientific and Technical Information (OSTI.GOV)

McNamara, Bruce K.; Buck, Edgar C.; Soderquist, Chuck Z.

2014-03-23

Nitrogen trifluoride (NF 3) was used to fluorinate the metallic residue from the dissolution of a high burnup, boiling water reactor fuel (~70 MWd/kgU). The metallic residue included the noble metal phase (containing ruthenium, rhodium, palladium, technetium, and molybdenum), and smaller amounts of zirconium, selenium, tellurium, and silver. Exposing the noble metal phase to 10% NF 3 in argon between 400 and 550°C, removed molybdenum and technetium near 400°C as their volatile fluorides, and ruthenium near 500C as its volatile fluoride. The events were thermally and temporally distinct and the conditions specified are a recipe to separate these transition metalsmore » from each other and from the noble metal phase nonvolatile residue. Depletion of the volatile fluorides resulted in substantial exothermicity. Thermal excursion behavior was recorded under non-adiabatic, isothermal conditions that typically minimize heat release. Physical characterization of the metallic noble phase and its thermal behavior are consistent with high kinetic velocity reactions encouraged by the nanoparticulate phase or perhaps catalytic influences of the mixed platinum metals with nearly pure phase structure. Post-fluorination, only two phases were present in the residual nonvolatile fraction. These were identified as a nano-crystalline, metallic palladium cubic phase and a hexagonal rhodium trifluoride (RhF 3) phase. The two phases were distinct as the sub-µm crystallites of metallic palladium were in contrast to the RhF 3 phase, which grew from the parent nano-crystalline noble-metal phase during fluorination, to acicular crystals exceeding 20-µm in length.« less

76 FR 49669 - Change of Address for Region 1; Technical Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-11

... organic compounds. 40 CFR Part 59 Environmental protection, Air pollution control, Confidential business information, Labeling, Ozone, Reporting and recordkeeping requirements, Volatile organic compounds. 40 CFR..., Copper, Dry cleaners, Electric power plants, Fertilizers, Fluoride, Gasoline, Glass and glass products...

Dry halide method for separating the components of spent nuclear fuels

DOEpatents

Christian, Jerry Dale; Thomas, Thomas Russell; Kessinger, Glen F.

1998-01-01

The invention is a nonaqueous, single method for processing multiple spent nuclear fuel types by separating the fission- and transuranic products from the nonradioactive and fissile uranium product. The invention has four major operations: exposing the spent fuels to chlorine gas at temperatures preferably greater than 1200.degree. C. to form volatile metal chlorides; removal of the fission product chlorides, transuranic product chlorides, and any nickel chloride and chromium chloride in a molten salt scrubber at approximately 400.degree. C.; fractional condensation of the remaining volatile chlorides at temperatures ranging from 164.degree. C. to 2.degree. C.; and regeneration and recovery of the transferred spent molten salt by vacuum distillation. The residual fission products, transuranic products, and nickel- and chromium chlorides are converted to fluorides or oxides for vitrification. The method offers the significant advantages of a single, compact process that is applicable to most of the diverse nuclear fuels, minimizes secondary wastes, segregates fissile uranium from the high level wastes to resolve potential criticality concerns, segregates nonradioactive wastes from the high level wastes for volume reduction, and produces a common waste form glass or glass-ceramic.

Dry halide method for separating the components of spent nuclear fuels

DOEpatents

Christian, J.D.; Thomas, T.R.; Kessinger, G.F.

1998-06-30

The invention is a nonaqueous, single method for processing multiple spent nuclear fuel types by separating the fission and transuranic products from the nonradioactive and fissile uranium product. The invention has four major operations: exposing the spent fuels to chlorine gas at temperatures preferably greater than 1200 C to form volatile metal chlorides; removal of the fission product chlorides, transuranic product chlorides, and any nickel chloride and chromium chloride in a molten salt scrubber at approximately 400 C; fractional condensation of the remaining volatile chlorides at temperatures ranging from 164 to 2 C; and regeneration and recovery of the transferred spent molten salt by vacuum distillation. The residual fission products, transuranic products, and nickel- and chromium chlorides are converted to fluorides or oxides for vitrification. The method offers the significant advantages of a single, compact process that is applicable to most of the diverse nuclear fuels, minimizes secondary wastes, segregates fissile uranium from the high level wastes to resolve potential criticality concerns, segregates nonradioactive wastes from the high level wastes for volume reduction, and produces a common waste form glass or glass-ceramic. 3 figs.

REGENERATION OF REACTOR FUEL ELEMENTS

DOEpatents

Lyon, W.L.

1960-04-01

A process is described for concentrating uranium and/or plutonium metal in aluminum alloys in which the actinide content was partially consumed by neutron bombardinent. Two embodiments are claimed: Either the alloy is heated, together with zinc chloride to at least 1000 deg C whereby some aluminum, in the form of aluminum chloride, and any zinc formed volatilize; or else aluminum fluoride is added and reacted at 800 to 1000 deg O and substmospheric pressure whereby pant of the aluminum volatilizes and aluminum subfluoride.

Evaluation of the direct and diffusion methods for the determination of fluoride content in table salt

PubMed Central

Martínez-Mier, E. Angeles; Soto-Rojas, Armando E.; Buckley, Christine M.; Margineda, Jorge; Zero, Domenick T.

2010-01-01

Objective The aim of this study was to assess methods currently used for analyzing fluoridated salt in order to identify the most useful method for this type of analysis. Basic research design Seventy-five fluoridated salt samples were obtained. Samples were analyzed for fluoride content, with and without pretreatment, using direct and diffusion methods. Element analysis was also conducted in selected samples. Fluoride was added to ultra pure NaCl and non-fluoridated commercial salt samples and Ca and Mg were added to fluoride samples in order to assess fluoride recoveries using modifications to the methods. Results Larger amounts of fluoride were found and recovered using diffusion than direct methods (96%–100% for diffusion vs. 67%–90% for direct). Statistically significant differences were obtained between direct and diffusion methods using different ion strength adjusters. Pretreatment methods reduced the amount of recovered fluoride. Determination of fluoride content was influenced both by the presence of NaCl and other ions in the salt. Conclusion Direct and diffusion techniques for analysis of fluoridated salt are suitable methods for fluoride analysis. The choice of method should depend on the purpose of the analysis. PMID:20088217

Synthesis and toxicity evaluation of hydrophobic ionic liquids for volatile organic compounds biodegradation in a two-phase partitioning bioreactor.

PubMed

Rodriguez Castillo, Alfredo Santiago; Guihéneuf, Solène; Le Guével, Rémy; Biard, Pierre-François; Paquin, Ludovic; Amrane, Abdeltif; Couvert, Annabelle

2016-04-15

Synthesis of several hydrophobic ionic liquids (ILs), which might be selected as good candidates for degradation of hydrophobic volatile organic compounds in a two-phase partitioning bioreactor (TPPB), were carried out. Several bioassays were also realized, such as toxicity evaluation on activated sludge and zebrafish, cytotoxicity, fluoride release in aqueous phase and biodegradability in order to verify their possible effects in case of discharge in the aquatic environment and/or human contact during industrial manipulation. The synthesized compounds consist of alkylimidazoliums, functionalized imidazoliums, isoqinoliniums, triazoliums, sulfoniums, pyrrolidiniums and morpholiniums and various counter-ions such as: PF6(-), NTf2(-) and NfO(-). Toxicity evaluation on activated sludge of each compound (5% v/v of IL) was assessed by using a glucose uptake inhibition test. Toxicity against zebrafish and cytotoxicity were evaluated by the ImPACCell platform of Rennes (France). Fluoride release in water was estimated by regular measurements using ion chromatography equipment. IL biodegradability was determined by measuring BOD28 of aqueous samples (compound concentration,1mM). All ILs tested were not biodegradable; while some of them were toxic toward activated sludge. Isoquinolinium ILs were toxic to human cancerous cell lines. Nevertheless no toxicity was found against zebrafish Danio rerio. Only one IL released fluoride after long-time agitation. Copyright © 2016 Elsevier B.V. All rights reserved.

REDUCTION OF FLUORIDE TO METAL

DOEpatents

Carlson, O.N.; Schmidt, F.A.; Spedding, F.H.

1960-08-30

A process is given for making yttrium metal by reducing yttrium fluoride with calcium plus magnesium. Calcium is added in an excess of from 10 to 20% and magnesium in a quantity to yield a magnesium--yttrium alloy containing from 12 to 25% magnesium when the reaction mass is heated in an inert atmosphere at from 900 to 1106 deg C, but preferably above the melting point of the alloy. Calcium chloride may be added so as to obtain a less viscous slag containing from 30 to 60% calcium chloride. After removal of the slag the alloy is vacuum-heated at about 1100 deg C for volatilization of the magnesium and calcium.

SEPARATION OF METAL VALUES FROM NUCLEAR REACTOR

DOEpatents

Campbell, D.O.; Cathers, G.I.

1962-06-19

A method is given for separating beryllium fluoride and an alkali metal fluoride from a mixture containing same and rare earth fluorides. The method comprises contacting said mixture with a liquid hydrogen fluoride solvent containing no more than about 30 per cent water by weight and saturated with a fluoride salt characterized by its solubility in anhydrous hydrogen fluoride for a period of time sufficient to dissolve said beryllium fluoride in said solvent. (AEC)

The effects of an anchovy (stolephorus insularis) substrate application on the level of fluor intrusion on Sprague Dawley rat teeth (in vivo)

NASA Astrophysics Data System (ADS)

Sakinah, N. R.; Gunawan, H. A.; Puspitawati, R.

2017-08-01

Fluoride intrusion is one of the efficacy parameters of fluoridation. Anchovy (Stolephorus insularis), which contains a high fluoride concentration in the CaF2compound, can be used as a fluoridative agent which is affordable and easily obtained. The aim of this study is to prove the effectiveness of the application of an anchovy substrate (Stolephorus insularis), either by a feeding method or a topical method, for tooth fluoridation based on the depth of fluoride intrusion on the enamel. An in vivo experimental laboratory method was used. The subjects were 14 Sprague Dawley rats divided into five groups. The groups included a baseline control, a feeding negative control, a topical negative control, an anchovy feeding method, and a topical solution anchovy method. After 15 days of treatment, the teeth were cut transversely with a 0.5 mm thickness then processed to test for fluoride intrusion using fluorescence microscopy. There was increased fluor intrusion on the enamel of the experimental groups compared to the negative control groups (p<0.05).Fluoride intrusion using the topical fluoride method is higher than with the feeding method (p <0.05). Thus, the application of an anchovy substrate, either by chewing or smearing, increases fluoride intrusion on the enamel.

Dependence of microsomal methoxyflurane O-demethylation on cytochrome P-450 reductase and the stoichiometry of fluoride ion and formaldehyde release.

PubMed

Waskell, L; Gonzales, J

1982-07-01

In order to characterize further the in vitro liver microsomal O-demethylation and defluorination of the volatile anesthetic methoxyflurane, and obtain additional information regarding the participation of cytochrome P-450 in the oxidation, the stoichiometry of the reaction was determined and the effect of antibody to cytochrome P-450 reductase on this unique biotransformation was examined. Liver microsomes were isolated from rabbits and rats in which enzyme induction had previously been produced by phenobarbital. The O-demethylation of methoxyflurane by phenobarbital-induced microsomes results in the production of 1 mol of formaldehyde for every 2 mol of fluoride ion produced. Dichloroacetic acid is also a product of methoxyflurane O-demethylation. Antibody to cytochrome P-450 reductase inhibits by 85% the amount of fluoride ion produced by the microsomal metabolism of methoxyflurane. Thus critical indirect supportive data are contributed to the hypothesis that at least one, but perhaps more, cytochrome P-450 is indeed responsible for methoxyflurane O-demethylation and defluorination.

Benefits of a silica-based fluoride toothpaste containing o-cymen-5-ol, zinc chloride and sodium fluoride.

PubMed

Newby, Craig S; Rowland, Joanna L; Lynch, Richard J M; Bradshaw, David J; Whitworth, Darren; Bosma, Mary Lynn

2011-08-01

Fluoride toothpastes in conjunction with tooth brushing are used to clean teeth, control plaque build-up and for anti-caries benefits. Toothpastes are designed with attractive flavours and appearances to encourage regular prolonged use to maximise these benefits. The incorporation of additional ingredients into toothpaste is a convenient way to provide supplementary protection that fits into people's everyday oral care routine. Such ingredients should not compromise the primary health benefits of toothpaste nor discourage its use. o-Cymen-5-ol and zinc chloride have been incorporated into a sodium fluoride (NaF)/silica toothpaste at 0.1%w/w and 0.6%w/w respectively to provide additional benefits. These include improved gingival health maintenance, in terms of the reduction of plaque, gingival index and bleeding, and an immediate and long lasting reduction in volatile sulfur compounds (VSCs) measured on breath. These benefits can be attributed to the antimicrobial and neutralisation actions of the toothpaste. The use of established fluoride models demonstrated no compromise in NaF bioavailability. The toothpaste was formulated without compromising product aesthetics. The combination of o-cymen-5-ol and zinc chloride in toothpaste gave superior maintenance of gingival health and reduction in malodour related VSCs without compromising the primary health benefits of the toothpaste or diminishing attributes preferred for the product's use. © 2011 FDI World Dental Federation.

Facile fabrication of highly ordered poly(vinylidene fluoride-trifluoroethylene) nanodot arrays for organic ferroelectric memory

NASA Astrophysics Data System (ADS)

Fang, Huajing; Yan, Qingfeng; Geng, Chong; Chan, Ngai Yui; Au, Kit; Yao, Jianjun; Ng, Sheung Mei; Leung, Chi Wah; Li, Qiang; Guo, Dong; Wa Chan, Helen Lai; Dai, Jiyan

2016-01-01

Nano-patterned ferroelectric materials have attracted significant attention as the presence of two or more thermodynamically equivalent switchable polarization states can be employed in many applications such as non-volatile memory. In this work, a simple and effective approach for fabrication of highly ordered poly(vinylidene fluoride-trifluoroethylene) P(VDF-TrFE) nanodot arrays is demonstrated. By using a soft polydimethylsiloxane mold, we successfully transferred the 2D array pattern from the initial monolayer of colloidal polystyrene nanospheres to the imprinted P(VDF-TrFE) films via nanoimprinting. The existence of a preferred orientation of the copolymer chain after nanoimprinting was confirmed by Fourier transform infrared spectra. Local polarization switching behavior was measured by piezoresponse force microscopy, and each nanodot showed well-formed hysteresis curve and butterfly loop with a coercive field of ˜62.5 MV/m. To illustrate the potential application of these ordered P(VDF-TrFE) nanodot arrays, the writing and reading process as non-volatile memory was demonstrated at a relatively low voltage. As such, our results offer a facile and promising route to produce arrays of ferroelectric polymer nanodots with improved piezoelectric functionality.

Apparatus and methods for purifying lead

DOEpatents

Tunison, Harmon M.

2016-01-12

Disclosed is an exemplary method of purifying lead which includes the steps of placing lead and a fluoride salt blend in a container; forming a first fluid of molten lead at a first temperature; forming a second fluid of the molten fluoride salt blend at a second temperature higher than the first temperature; mixing the first fluid and the second fluid together; separating the two fluids; solidifying the molten fluoride salt blend at a temperature above a melting point of the lead; and removing the molten lead from the container. In certain exemplary methods the molten lead is removed from the container by decanting. In still other exemplary methods the molten salt blend is a Lewis base fluoride eutectic salt blend, and in yet other exemplary methods the molten salt blend contains sodium fluoride, lithium fluoride, and potassium fluoride.

Fluorination process using catalyst

DOEpatents

Hochel, Robert C.; Saturday, Kathy A.

1985-01-01

A process for converting an actinide compound selected from the group consisting of uranium oxides, plutonium oxides, uranium tetrafluorides, plutonium tetrafluorides and mixtures of said oxides and tetrafluorides, to the corresponding volatile actinide hexafluoride by fluorination with a stoichiometric excess of fluorine gas. The improvement involves conducting the fluorination of the plutonium compounds in the presence of a fluoride catalyst selected from the group consisting of CoF.sub.3, AgF.sub.2 and NiF.sub.2, whereby the fluorination is significantly enhanced. The improvement also involves conducting the fluorination of one of the uranium compounds in the presence of a fluoride catalyst selected from the group consisting of CoF.sub.3 and AgF.sub.2, whereby the fluorination is significantly enhanced.

Fluorination process using catalysts

DOEpatents

Hochel, R.C.; Saturday, K.A.

1983-08-25

A process is given for converting an actinide compound selected from the group consisting of uranium oxides, plutonium oxides, uranium tetrafluorides, plutonium tetrafluorides and mixtures of said oxides and tetrafluorides, to the corresponding volatile actinide hexafluoride by fluorination with a stoichiometric excess of fluorine gas. The improvement involves conducting the fluorination of the plutonium compounds in the presence of a fluoride catalyst selected from the group consisting of CoF/sub 3/, AgF/sub 2/ and NiF/sub 2/, whereby the fluorination is significantly enhanced. The improvement also involves conducting the fluorination of one of the uranium compounds in the presence of a fluoride catalyst selected from the group consisting of CoF/sub 3/ and AgF/sub 2/, whereby the fluorination is significantly enhanced.

Recovery of Agricultural Odors and Odorous Compounds from Polyvinyl Fluoride Film Bags

PubMed Central

Parker, David B.; Perschbacher-Buser, Zena L.; Cole, N. Andy; Koziel, Jacek A.

2010-01-01

Accurate sampling methods are necessary when quantifying odor and volatile organic compound emissions at agricultural facilities. The commonly accepted methodology in the U.S. has been to collect odor samples in polyvinyl fluoride bags (PVF, brand name Tedlar®) and, subsequently, analyze with human panelists using dynamic triangular forced-choice olfactometry. The purpose of this research was to simultaneously quantify and compare recoveries of odor and odorous compounds from both commercial and homemade PVF sampling bags. A standard gas mixture consisting of p-cresol (40 μg m−3) and seven volatile fatty acids: acetic (2,311 μg m−3), propionic (15,800 μg m−3), isobutyric (1,686 μg m−3), butyric (1,049 μg m−3), isovaleric (1,236 μg m−3), valeric (643 μg m−3), and hexanoic (2,158 μg m−3) was placed in the PVF bags at times of 1 h, 1 d, 2 d, 3 d, and 7 d prior to compound and odor concentration analyses. Compound concentrations were quantified using sorbent tubes and gas chromatography/mass spectrometry. Odor concentration, intensity, and hedonic tone were measured using a panel of trained human subjects. Compound recoveries ranged from 2 to 40% after 1 h and 0 to 14% after 7 d. Between 1 h and 7 d, odor concentrations increased by 45% in commercial bags, and decreased by 39% in homemade bags. Minimal changes were observed in intensity and hedonic tone over the same time period. These results suggest that PVF bags can bias individual compound concentrations and odor as measured by dynamic triangular forced-choice olfactometry. PMID:22163671

[Fluoridation of drinking water, why is it needed?].

PubMed

Zusman, S P; Natapov, L; Ramon, T

2004-01-01

Dental caries is a widespread disease. It causes irreversible damage, pain and considerable expense. Fluoride is the only known substance that raises the tooth's resistance to acid attack. Natural drinking waters contain fluoride at different concentration. The most effective method of fluoride administration to the community level is by adjustng the fluoride concentration in the drinking water to about 1 part per million. To describe the mode of action of fluoride, methods of administration and to describe water fluoridation, advantages and disadvantages. Fluoridation of drinking water started in 1945 in the world and in 1981 in Israel. Today more then 300 million people in some 60 countries enjoy the defending effect of fluoride in drinking water. This is the most effective method for decreasing incidence of caries, as well as being cost effective. Over the years there were many attempts to 'blame' fluoridation with negative side effects to human health. Till today, none of the allegations passed scientific scrutiny. There is overwhelming scientific support for the Regulations that oblige the Water supplier to adjust fluoride levels to 1 ppm in every town or municipality with more then 5,000 inhabitants.

Capillary electrophoresis with contactless conductivity detection for the quantification of fluoride in lithium ion battery electrolytes and in ionic liquids-A comparison to the results gained with a fluoride ion-selective electrode.

PubMed

Pyschik, Marcelina; Klein-Hitpaß, Marcel; Girod, Sabrina; Winter, Martin; Nowak, Sascha

2017-02-01

In this study, an optimized method using capillary electrophoresis (CE) with a direct contactless conductivity detector (C 4 D) for a new application field is presented for the quantification of fluoride in common used lithium ion battery (LIB) electrolyte using LiPF 6 in organic carbonate solvents and in ionic liquids (ILs) after contacted to Li metal. The method development for finding the right buffer and the suitable CE conditions for the quantification of fluoride was investigated. The results of the concentration of fluoride in different LIB electrolyte samples were compared to the results from the ion-selective electrode (ISE). The relative standard deviations (RSDs) and recovery rates for fluoride were obtained with a very high accuracy in both methods. The results of the fluoride concentration in the LIB electrolytes were in very good agreement for both methods. In addition, the limit of detection (LOD) and limit of quantification (LOQ) values were determined for the CE method. The CE method has been applied also for the quantification of fluoride in ILs. In the fresh IL sample, the concentration of fluoride was under the LOD. Another sample of the IL mixed with Li metal has been investigated as well. It was possible to quantify the fluoride concentration in this sample. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Rare earth elements in apatite: Uptake from H{sub 2}O-bearing phosphate-fluoride melts and the role of volatile components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fleet, M.E.; Pan, Yuanming

The partitioning of rare earth elements (REEs) between fluorapatite (FAp) and H{sub 2}O- bearing phosphate-fluoride melts has been studied at about 700 and 800{degrees}C and 0.10-0.15 GPa. REE uptake patterns, i.e., plots of D(REE:FAp/melt), are convex upwards and peak near Nd for single-REE substituted FAp at minor (0.03-0.25 wt% REE{sub 2}O{sub 3}) abundances, and binary (LREE + HREE)-substituted FAp, and hexa-REE-substituted FAp at minor to major (0.25-7.8 wt% REE{sub 2}O{sub 3}) abundances. Partition coefficients for minor abundances of REE and depolymerized phosphate melts are about 5, 8, and 1 for La, Nd, and Lu, respectively and broadly comparable to thosemore » for early fluorapatite in the fractionation of melts of basaltic composition. The Ca2 site exerts marked control on the selectivity of apatite for REE because it preferentially incorporates LREE and its effective size varies with substitution of the A-site volatile anion component (F, Cl, OH). Using simple crystal-chemical arguments, melt(or fluid)-normalized REE patterns are predicted to peak near Nd for fluorapatite and be more LREE-enriched for chlorapatite. These predictions are consistent with data from natural rocks and laboratory experiments. The wide variation in D(REE:apatite/melt) in nature (from <1 for whitlockite-bearing lunar rocks to about 100 for evolved alkalic rocks) is attributed largely to the influence of the volatile components. 49 refs., 8 figs., 3 tabs.« less

METHOD FOR DISSOLVING LANTHANUM FLUORIDE CARRIER FOR PLUTONIUM

DOEpatents

Koshland, D.E. Jr.; Willard, J.E.

1961-08-01

A method is described for dissolving lanthanum fluoride precipitates which is applicable to lanthanum fluoride carrier precipitation processes for recovery of plutonium values from aqueous solutions. The lanthanum fluoride precipitate is contacted with an aqueous acidic solution containing dissolved zirconium in the tetravalent oxidation state. The presence of the zirconium increases the lanthanum fluoride dissolved and makes any tetravalent plutonium present more readily oxidizable to the hexavalent state. (AEC)

Methods of controlling hydrogen fluoride pressure during chemical fabrication processes

DOEpatents

Solovyov, Vyacheslav [Rocky Point, NY; Wiesmann, Harold [Stony Brook, NY

2009-11-24

The present invention is a method for producing a crystalline end-product. The method comprising exposing a fluoride-containing precursor to a hydrogen fluoride absorber under conditions suitable for the conversion of the precursor into the crystalline end-product.

Determination of fluoride in oxides with the fluoride-ion activity electrode.

PubMed

Peters, M A; Ladd, D M

1971-07-01

The application of the fluoride-ion activity electrode to the determination of fluoride in various samples has been studied. Samples are decomposed by fusion and the fluoride concentration is determined by a standard-addition or a direct method. The standard-addition method is unsuitable, owing to a positive bias. The direct method, however, is rapid, accurate and precise. The fluoride content of exploration ores, fluorspar, opal glass, phosphate rock and various production samples, has been successfully determined. The success of the direct method depends on the effectiveness of the system used to buffer pH and ionic strength and complex possible interferences (Al(3+), Ca(2+), Fe(3+)). The effect of interferences has been studied and found to be minimal. The procedures are rapid and accurate and may be substituted for the traditional Willard and Winter or pyro hydrolysis methods, with considerable saving of time.

Metabolite Identification of Halon Replacement Compounds.

DTIC Science & Technology

1992-06-01

inhalation to a 1 % atmosphere for 2 h. Tlissues were analyzed for volatile metabolites, and urine was analyzed for fluoride and carboxylic acid metabolites...M*vass Spectrometry, lialocarbons, 35 lialon 1211, IICFC- 123, IICIFC 124, IICFC 142b, llvdro~chlorofluoro-tcarbIonis ( 1 ICFCs), Inhalation Exposure...trifluoroethane HCFC- 142b 1 -Chloro-1,1 - difluoroethane HCI Hydrochloric acid kg Kilogram L Liter m Meter M Moles/liter mg Milligram MHz Megahertz min Minute

Validating a High Performance Liquid Chromatography-Ion Chromatography (HPLC-IC) Method with Conductivity Detection After Chemical Suppression for Water Fluoride Estimation.

PubMed

Bondu, Joseph Dian; Selvakumar, R; Fleming, Jude Joseph

2018-01-01

A variety of methods, including the Ion Selective Electrode (ISE), have been used for estimation of fluoride levels in drinking water. But as these methods suffer many drawbacks, the newer method of IC has replaced many of these methods. The study aimed at (1) validating IC for estimation of fluoride levels in drinking water and (2) to assess drinking water fluoride levels of villages in and around Vellore district using IC. Forty nine paired drinking water samples were measured using ISE and IC method (Metrohm). Water samples from 165 randomly selected villages in and around Vellore district were collected for fluoride estimation over 1 year. Standardization of IC method showed good within run precision, linearity and coefficient of variance with correlation coefficient R 2  = 0.998. The limit of detection was 0.027 ppm and limit of quantification was 0.083 ppm. Among 165 villages, 46.1% of the villages recorded water fluoride levels >1.00 ppm from which 19.4% had levels ranging from 1 to 1.5 ppm, 10.9% had recorded levels 1.5-2 ppm and about 12.7% had levels of 2.0-3.0 ppm. Three percent of villages had more than 3.0 ppm fluoride in the water tested. Most (44.42%) of these villages belonged to Jolarpet taluk with moderate to high (0.86-3.56 ppm) water fluoride levels. Ion Chromatography method has been validated and is therefore a reliable method in assessment of fluoride levels in the drinking water. While the residents of Jolarpet taluk (Vellore distict) are found to be at a high risk of developing dental and skeletal fluorosis.

Salt fluoridation and oral health.

PubMed

Marthaler, Thomas M

2013-11-01

The aim of this paper is to make known the potential of fluoridated salt in community oral health programs, particularly in South Eastern Europe. Since 1922, the addition of iodine to salt has been successful in Switzerland. Goiter is virtually extinct. By 1945, the caries-protective effect of fluorides was well established. Based on the success of water fluoridation, a gynecologist started adding of fluoride to salt. The sale of fluoridated salt began in 1956 in the Swiss Canton of Zurich, and several other cantons followed suit. Studies initiated in the early seventies showed that fluoride, when added to salt, inhibits dental caries. The addition of fluoride to salt for human consumption was officially authorized in 1980-82. In Switzerland 85% of domestic salt consumed is fluoridated and 67% in Germany. Salt fluoridation schemes are reaching more than one hundred million in Mexico, Colombia, Peru and Cuba. The cost of salt fluoridation is very low, within 0.02 and 0.05 € per year and capita. Children and adults of the low socio-economic strata tend to have substantially more untreated caries than higher strata. Salt fluoridation is by far the cheapest method for improving oral health. Salt fluoridation has cariostatic potential like water fluoridation (caries reductions up to 50%). In Europe, meaningful percentages of users have been attained only in Germany (67%) and Switzerland (85%). In Latin America, there are more than 100 million users, and several countries have arrived at coverage of 90 to 99%. Salt fluoridation is by far the cheapest method of caries prevention, and billions of people throughout the world could benefit from this method. Copyright © 2013 by Academy of Sciences and Arts of Bosnia and Herzegovina.

Solution of rocks and refractory minerals by acids at high temperatures and pressures. Determination of silica after decomposition with hydrofluoric acid

USGS Publications Warehouse

May, I.; Rowe, J.J.

1965-01-01

A modified Morey bomb was designed which contains a removable nichromecased 3.5-ml platinium crucible. This bomb is particularly useful for decompositions of refractory samples for micro- and semimicro-analysis. Temperatures of 400-450?? and pressures estimated as great as 6000 p.s.i. were maintained in the bomb for periods as long as 24 h. Complete decompositions of rocks, garnet, beryl, chrysoberyl, phenacite, sapphirine, and kyanite were obtained with hydrofluoric acid or a mixture of hydrofluoric and sulfuric acids; the decomposition of chrome refractory was made with hydrochloric acid. Aluminum-rich samples formed difficultly soluble aluminum fluoride precipitates. Because no volatilization losses occur, silica can be determined on sample solutions by a molybdenum-blue procedure using aluminum(III) to complex interfering fluoride. ?? 1965.

Levels of Antioxidant Activity and Fluoride Content in Coffee Infusions of Arabica, Robusta and Green Coffee Beans in According to their Brewing Methods.

PubMed

Wolska, J; Janda, Katarzyna; Jakubczyk, K; Szymkowiak, M; Chlubek, D; Gutowska, I

2017-10-01

Coffee is a rich source of dietary antioxidants, and this property links with the fact that coffee is one of the world's most popular beverages. Moreover, it is a source of macro- and microelements, including fluoride. The aim of this work was to determine antioxidant activity of coffee beverages and fluoride content depending on different coffee species and conditions of brewing. Three species of coffee, arabica, robusta and green coffee beans obtained from retail stores in Szczecin (Poland) were analyzed. Five different techniques of preparing drink were used: simple infusion, french press, espresso maker, overflow espresso and Turkish coffee. Antioxidant potential of coffee beverages was investigated spectrophotometrically by DPPH method. Fluoride concentrations were measured by potentiometric method with a fluoride ion-selective electrode. Statistical analysis was performed using Stat Soft Statistica 12.5. Antioxidant activity of infusions was high (71.97-83.21% inhibition of DPPH) depending on coffee species and beverage preparing method. It has been shown that the method of brewing arabica coffee and green coffee significantly affects the antioxidant potential of infusions. The fluoride concentration in the coffee infusions changed depending, both, on the species and conditions of brewing, too (0.013-0.502 mg/L). Methods of brewing didn't make a difference to the antioxidant potential of robusta coffee, which had also the lowest level of fluoride among studied species. Except overflow espresso, the fluoride content was the highest in beverages from green coffee. The highest fluoride content was found in Turkish coffee from green coffee beans.

Fluoridation and Defluoridation. Training Module 2.230.2.77.

ERIC Educational Resources Information Center

McMullen, L. D.

This document is an instructional module package prepared in objective form for use by an instructor familiar with fluoridation and fluoride feeding equipment. Enclosed are objectives, an instructor guide, student handouts and transparency masters. The module considers the principles and purposes of fluoridation, methods of feeding fluoride,…

The impact of changing dental needs on cost savings from fluoridation.

PubMed

Campain, A C; Mariño, R J; Wright, F A C; Harrison, D; Bailey, D L; Morgan, M V

2010-03-01

Although community water fluoridation has been one of the cornerstone strategies for the prevention and control of dental caries, questions are still raised regarding its cost-effectiveness. This study assessed the impact of changing dental needs on the cost savings from community water fluoridation in Australia. Net costs were estimated as Costs((programme)) minus Costs((averted caries).) Averted costs were estimated as the product of caries increment in non-fluoridated community, effectiveness of fluoridation and the cost of a carious surface. Modelling considered four age-cohorts: 6-20, 21-45, 46-65 and 66+ years and three time points 1970s, 1980s, and 1990s. Cost of a carious surface was estimated by conventional and complex methods. Real discount rates (4, 7 (base) and 10%) were utilized. With base-case assumptions, the average annual cost savings/person, using Australian dollars at the 2005 level, ranged from $56.41 (1970s) to $17.75 (1990s) (conventional method) and from $249.45 (1970s) to $69.86 (1990s) (complex method). Under worst-case assumptions fluoridation remained cost-effective with cost savings ranging from $24.15 (1970s) to $3.87 (1990s) (conventional method) and $107.85 (1970s) and $24.53 (1990s) (complex method). For 66+ years cohort (1990s) fluoridation did not show a cost saving, but costs/person were marginal. Community water fluoridation remains a cost-effective preventive measure in Australia.

Alimentary fluoride intake in preschool children

PubMed Central

2011-01-01

Background The knowledge of background alimentary fluoride intake in preschool children is of utmost importance for introducing optimal and safe caries preventive measures for both individuals and communities. The aim of this study was to assess the daily fluoride intake analyzing duplicate samples of food and beverages. An attempt was made to calculate the daily intake of fluoride from food and swallowed toothpaste. Methods Daily alimentary fluoride intake was measured in a group of 36 children with an average age of 4.75 years and an average weight of 20.69 kg at baseline, by means of a double plate method. This was repeated after six months. Parents recorded their child's diet over 24 hours and collected duplicated portions of food and beverages received by children during this period. Pooled samples of food and beverages were weighed and solid food samples were homogenized. Fluoride was quantitatively extracted from solid food samples by a microdiffusion method using hexadecyldisiloxane and perchloric acid. The content of fluoride extracted from solid food samples, as well as fluoride in beverages, was measured potentiometrically by means of a fluoride ion selective electrode. Results Average daily fluoride intake at baseline was 0.389 (SD 0.054) mg per day. Six months later it was 0.378 (SD 0.084) mg per day which represents 0.020 (SD 0.010) and 0.018 (SD 0.008) mg of fluoride respectively calculated per kg bw/day. When adding the values of unwanted fluoride intake from the toothpaste shown in the literature (0.17-1.21 mg per day) the estimate of the total daily intake of fluoride amounted to 0.554-1.594 mg/day and recalculated to the child's body weight to 0.027-0.077 mg/kg bw/day. Conclusions In the children studied, observed daily fluoride intake reached the threshold for safe fluoride intake. When adding the potential fluoride intake from swallowed toothpaste, alimentary intake reached the optimum range for daily fluoride intake. These results showed that in preschool children, when trying to maximize the benefit of fluoride in caries prevention and to minimize its risk, caution should be exercised when giving advice on the fluoride containing components of child's diet or prescribing fluoride supplements. PMID:21974798

Fluoride in drinking water and human urine in Southern Haryana, India.

PubMed

Singh, Bhupinder; Gaur, Shalini; Garg, V K

2007-06-01

The objective of this study was to determine the fluoride content in drinking water and urine samples of adolescent males aged 11-16 years living in Southern Haryana, India. A total of 30 drinking water sources in the studied habitations were assessed for fluoride contamination. Fluoride was estimated in the urine of 400 male children randomly selected from these habitations. The fluoride concentration in drinking water and urine samples was determined using USEPA fluoride ion selective electrode method. The mean fluoride concentration in drinking water samples of Pataudi, Haily Mandi and Harsaru villages was 1.68+/-0.35, 3.22+/-1.18 and 1.78+/-0.12 mg/l, respectively. The mean urinary fluoride concentration was 2.26+/-0.024 mg/l at Pataudi, 2.48+/-0.77 mg/l at Haily Mandi and 2.43+/-0.84 mg/l at Harsaru village. The higher fluoride levels in the urine of children may be associated to higher fluoride levels in drinking water. The accuracy of measurements was assessed with known addition method in water and urine. Mean fluoride recovery was 98.0 and 99.1% in water and urine. The levels obtained were reproducible with in +/-3% error limit.

Aerodynamic Levitation Reactor Studies of Fluorine Reactions with Refractory Ceramics

DTIC Science & Technology

1981-05-01

Melting Points of Rare-Earth Metals and Rare-Earth Trifluorides . 14 3. Aerodynamic Lavitation Flow Reactor. 15 4 Lanthanutm-Boron-Carbon Ternary Phase...the least volatile fluorides (CaF , SrT and rare-earth trifluorides ) would yield a 10% increase in w* (initially O.O cam) in about 1 hour at 1300K...measurement, and are, therefore, somewhat uncertain. The melting points of the rare-earth metals and their trifluorides are illustrated in Fig. 2. The melting

Volatiles on the surface of Apollo 15 green glass and trace-element distributions among Apollo 15 soils

NASA Technical Reports Server (NTRS)

Chou, C.-L.; Boynton, W. V.; Sundberg, L. L.; Wasson, J. T.

1975-01-01

Zn, Ge, Cd, In, and Au have been detected in surficial deposits on Apollo 15 green-glass spherules, and it is suggested that these deposits are condensates from the magmatic gas phase which was responsible for the pneumatic expulsion of the green glass from the lunar interior. Thermodynamic data indicate that chlorides and fluorides were the dominant forms of the volatile metals. The Ar-40x content of a nongreen-glass soil fraction is greater than that found in green-glass. Mare and low-K Fra Mauro basalts seem to be the most prominent components of Apollo 15 soil. The correlation of Zn with Ar-40x and with Pb-204 is studied, and the distribution of quartz-normative and olivine-normative basalts is considered.

Fluorescent Sensing of Fluoride in Cellular System

PubMed Central

Jiao, Yang; Zhu, Baocun; Chen, Jihua; Duan, Xiaohong

2015-01-01

Fluoride ions have the important roles in a lot of physiological activities related with biological and medical system, such as water fluoridation, caries treatment, and bone disease treatment. Great efforts have been made to develop new methods and strategies for F- detection in the past decades. Traditional methods for the detection of F- including ion chromatography, ion-selective electrodes, and spectroscopic techniques have the limitations in the biomedicine research. The fluorescent probes for F- are very promising that overcome some drawbacks of traditional fluoride detection methods. These probes exhibit high selectivity, high sensitivity as well as quick response to the detection of fluoride anions. The review commences with a brief description of photophysical mechanisms for fluorescent probes for fluoride, including photo induced electron transfer (PET), intramolecular charge transfer (ICT), fluorescence resonance energy transfer (FRET), and excited-state intramolecular proton transfer (ESIPT). Followed by a discussion about common dyes for fluorescent fluoride probes, such as anthracene, naphalimide, pyrene, BODIPY, fluorescein, rhodamine, resorufin, coumarin, cyanine, and near-infrared (NIR) dyes. We divide the fluorescent probes for fluoride in cellular application systems into nine groups, for example, type of hydrogen bonds, type of cleavage of Si-O bonds, type of Si-O bond cleavage and cylization reactions, etc. We also review the recent reported carriers in the delivery of fluorescent fluoride probes. Seventy-four typical fluorescent fluoride probes are listed and compared in detail, including quantum yield, reaction medium, excitation and emission wavelengths, linear detection range, selectivity for F-, mechanism, and analytical applications. Finally, we discuss the future challenges of the application of fluorescent fluoride probes in cellular system and in vivo. We wish that more and more excellent fluorescent fluoride probes will be developed and applied in the biomedicine field in the future. PMID:25553106

Development of Gold Standard Ion-Selective Electrode-Based Methods for Fluoride Analysis

PubMed Central

Martínez-Mier, E.A.; Cury, J.A.; Heilman, J.R.; Katz, B.P.; Levy, S.M.; Li, Y.; Maguire, A.; Margineda, J.; O’Mullane, D.; Phantumvanit, P.; Soto-Rojas, A.E.; Stookey, G.K.; Villa, A.; Wefel, J.S.; Whelton, H.; Whitford, G.M.; Zero, D.T.; Zhang, W.; Zohouri, V.

2011-01-01

Background/Aims: Currently available techniques for fluoride analysis are not standardized. Therefore, this study was designed to develop standardized methods for analyzing fluoride in biological and nonbiological samples used for dental research. Methods A group of nine laboratories analyzed a set of standardized samples for fluoride concentration using their own methods. The group then reviewed existing analytical techniques for fluoride analysis, identified inconsistencies in the use of these techniques and conducted testing to resolve differences. Based on the results of the testing undertaken to define the best approaches for the analysis, the group developed recommendations for direct and microdiffusion methods using the fluoride ion-selective electrode. Results Initial results demonstrated that there was no consensus regarding the choice of analytical techniques for different types of samples. Although for several types of samples, the results of the fluoride analyses were similar among some laboratories, greater differences were observed for saliva, food and beverage samples. In spite of these initial differences, precise and true values of fluoride concentration, as well as smaller differences between laboratories, were obtained once the standardized methodologies were used. Intraclass correlation coefficients ranged from 0.90 to 0.93, for the analysis of a certified reference material, using the standardized methodologies. Conclusion The results of this study demonstrate that the development and use of standardized protocols for F analysis significantly decreased differences among laboratories and resulted in more precise and true values. PMID:21160184

Level of Fluoride in Soil, Grain and Water in Jalgaon District, Maharashtra, India.

PubMed

Naik, Rahul Gaybarao; Dodamani, Arun Suresh; Vishwakarma, Prashanth; Jadhav, Harish Chaitram; Khairnar, Mahesh Ravindra; Deshmukh, Manjiri Abhay; Wadgave, Umesh

2017-02-01

Fluoride has an influence on both oral as well as systemic health. The major source of fluoride to body is through drinking water as well as through diet. Staple diet mainly depends on local environmental factors, food grains grown locally, its availability etc. Determination of fluoride level in these food grains is important. So, estimation of the amount of fluoride in grains and its relation to the sources of fluoride used for their cultivation viz., soil and water is important. To estimate the relation of fluoride concentration in grains (Jowar) with respect to that of soil and water used for their cultivation. Fifteen samples each of soil, water and grains were collected using standardized method from the same farm fields of randomly selected villages of Jalgaon district. Fluoride ion concentration was determined in laboratory using SPADNS technique. Mean difference in fluoride levels in between the groups were analyzed using ANOVA and Post-Hoc Tukey test. Linear regression method was applied to analyse the association of the fluoride content of grain with water and soil. There was a significant difference in between mean fluoride levels of soil and water (p<0.001) and in between soil and grain (p<0.001); however, difference in between mean fluoride levels of water and grain was found to be non significant (p=0.591). Also fluoride levels in all the three groups showed significant association with each other. Fluoride level of soil, grains and water should be adjusted to an optimum level. Soil has positive correlation with respect to uptake of fluoride by Jowar grains. So, Jowar grains with optimum fluoride content should be made available in the commercial markets so that oral and general health can be benefitted.

SEPARATION OF PROTACTINIUM FROM MOLTEN SALT REACTOR FUEL COMPOSITIONS

DOEpatents

Shaffer, J.H.; Strain, J.E.; Cuneo, D.R.; Kelly, M.J.

1963-11-12

A method for selectively precipitating protactinium from a neutron- irradiated fused fluoride salt composition comprising at least one metal fluoride selected from the group consisting of an alkali metal fluoride and an alkaline earth metal fluoride containing dissolved thorium-232 values is presented. An inorganic metal oxide corresponding to any of the metal fluorides of the composition is also added. (AEC)

Chemico-therapeutic approach to prevention of dental caries. [using stannous fluoride gel

NASA Technical Reports Server (NTRS)

Shannon, I. L.

1975-01-01

The program of chemical preventive dentistry is based primarily upon the development of a procedure for stabilizing stannous fluoride in solution by forcing it into glycerin. New topical fluoride treatment concentrates, fluoride containing gels and prophylaxis pastes, as well as a completely stable stannous fluoride dentifrice are made possible by the development of a rather complicated heat application method to force stannous fluoride into solution in glycerin. That the stannous fluoride is clinically effective in such a preparation is demonstrated briefly on orthodontic patients.

Reducing Exposure to High Fluoride Drinking Water in Estonia—A Countrywide Study

PubMed Central

Indermitte, Ene; Saava, Astrid; Karro, Enn

2014-01-01

Fluoride is a naturally occurring contaminant in groundwater in Estonia. There are several regions in Estonia with fluoride contents in public water supplies as high as 7 mg/L. Long-term exposure to high-fluoride drinking water may have several adverse health effects, primarily dental fluorosis. The opportunities for exposure reduction rely highly on water treatment technologies. Since 2004 public water suppliers in Estonia have made efforts to diminish fluoride content in drinking water systems. A follow-up study on a country level was carried out in 2004–2012 to analyze the changes in population exposure to excessive (over 1.5 mg/L) fluoride in drinking water and to get information about the reduction methods applied by public water supplies (PWS) to optimize the fluoride levels in public water system. The results showed that bigger PWS have been more effective in fluoride reduction measures than small PWS. The main methods used to lower the fluoride content were reverse osmosis technology and replacement of water sources with new ones (new drilled wells). As a result of all the measures taken the overall high-fluoride exposure has been reduced substantially (82%). PMID:24637908

Reducing exposure to high fluoride drinking water in Estonia-a countrywide study.

PubMed

Indermitte, Ene; Saava, Astrid; Karro, Enn

2014-03-14

Fluoride is a naturally occurring contaminant in groundwater in Estonia. There are several regions in Estonia with fluoride contents in public water supplies as high as 7 mg/L. Long-term exposure to high-fluoride drinking water may have several adverse health effects, primarily dental fluorosis. The opportunities for exposure reduction rely highly on water treatment technologies. Since 2004 public water suppliers in Estonia have made efforts to diminish fluoride content in drinking water systems. A follow-up study on a country level was carried out in 2004-2012 to analyze the changes in population exposure to excessive (over 1.5 mg/L) fluoride in drinking water and to get information about the reduction methods applied by public water supplies (PWS) to optimize the fluoride levels in public water system. The results showed that bigger PWS have been more effective in fluoride reduction measures than small PWS. The main methods used to lower the fluoride content were reverse osmosis technology and replacement of water sources with new ones (new drilled wells). As a result of all the measures taken the overall high-fluoride exposure has been reduced substantially (82%).

Lunar mining of oxygen using fluorine

NASA Technical Reports Server (NTRS)

Burt, Donald M.

1992-01-01

An important aspect of lunar mining will be the extraction of volatiles, particularly oxygen, from lunar rocks. Thermodynamic data show that oxygen could readily be recovered by fluorination of abundant lunar anorthite, CaAl2Si2O8. Fluorine is the most reactive element, and the only reagent able to extract 100 percent of the oxygen from any mineral, yet it can safely be stored or reacted in nickel or iron containers. The general fluorination reaction, mineral + 2F2 = mixed fluorides = O2, has been used for more than 30 years at a laboratory scale by stable-isotope geochemists. For anorthite, metallic Al and Si may be recovered from the mixed fluorides by Na-reduction, and CaO via exchange with Na2O; the resulting NaF may be recycled into F2 and Na by electrolysis, using lanthanide-doped CaF2 as the inert anode.

Assessment of relative flammability and thermochemical properties of some thermoplastic materials

NASA Technical Reports Server (NTRS)

Kourtides, D. A.; Parker, J. A.

1978-01-01

The thermochemical and flammability characteristics of some typical thermoplastic materials currently in use and others being considered for use in aircraft interiors are described. The properties studied included (1) thermal mechanical properties such as glass transition and melt temperature, (2) changes in polymer enthalpy by differential scanning calorimetry, (3) thermogravimetric analysis in an anaerobic and oxidative environment, (4) oxygen index, (5) smoke evolution, (6) relative toxicity of the volatile products of pyrolysis, and (7) selected physical properties. The generic polymers which were evaluated included: acrylonitrile-butadiene-styrene, bisphenol A polycarbonate, bisphenol fluorenone carbonatedimethylsiloxane block polymer, phenolphthalein-bisphenol A polycarbonate, phenolphthalein polycarbonate, polyether sulfone, polyphenylene oxide, polyphenylene sulfide, polyaryl sulfone, chlorinated polyvinyl chloride homopolymer, polyvinyl fluoride, and polyvinylidene fluoride. Processing parameters including molding characteristics of some of the advanced polymers are described. Test results and relative rankings of some of the flammability, smoke and toxicity properties are presented.

Thermoplastic polymers for improved fire safety

NASA Technical Reports Server (NTRS)

Kourtides, D. A.; Parker, J. A.; Hilado, C. J.

1976-01-01

The thermochemical and flammability characteristics of some typical thermoplastic materials currently in use and others being considered for use in aircraft interiors are described. The properties studied included (1) thermomechanical properties such as glass transition and melt temperature, (2) changes in polymer enthalpy by differential scanning calorimetry, (3) thermogravimetric analysis in anaerobic and oxidative environments, (4) oxygen index, (5) smoke evolution, (6) relative toxicity of the volatile products of pyrolysis, and (7) selected physical properties. The generic polymers that were evaluated included: acrylonitrile butadiene styrene, bisphenol A polycarbonate, 9,9 bis (4-hydroxyphenyl) fluorene polycarbonatepoly (dimethyl siloxane) block polymer, phenolphthalein bisphenol A polycarbonate, phenolphthalein polycarbonate, polyether sulfone, polyphenylene oxide, polyphenylene sulfide, polyaryl sulfone, chlorinated polyvinyl chloride homopolymer, polyvinyl fluoride, and polyvinylidene fluoride. Processing parameters, including molding characteristics of some of the advanced polymers, are described. Test results and relative ranking of some of the flammability, smoke, and toxicity properties are presented.

Fluoride content of clay minerals and argillaceous earth materials

USGS Publications Warehouse

Thomas, Josephus; Glass, H.D.; White, W.A.; Trandel, R.M.

1977-01-01

A reliable method, utilizing a fluoride ion-selective electrode, is described for the determination of fluoride in clays and shales. Interference by aluminum and iron is minimal. The reproducibility of the method is about ±5% at different levels of fluoride concentration.Data are presented for various clay minerals and for the <2-µm fractions of marine and nonmarine clays and shales. Fluoride values range from 44 ppm (0.0044%) for nontronite from Colfax, WA, to 51,800 ppm (5.18%) for hectorite from Hector, CA. In general, clays formed under hydrothermal conditions are relatively high in fluoride content, provided the hydrothermal waters are high in fluoride content. Besides hectorite, dickite from Ouray, CO, was found to contain more than 50 times as much fluoride (6700 ppm) as highly crystalline geode kaolinite (125 ppm). The clay stratum immediately overlying a fluorite mineralized zone in southern Illinois was found to have a higher fluoride content than the same stratum in a nonmineralized zone approximately 1 mile away. Nonmarine shales in contact with Australian coals were found to be lower in fluoride content than were marine shales in contact with Illinois coals.It is believed that, in certain instances, peak shifts on DTA curves of similar clay minerals are the result of significant differences in their fluoride content.

Comparative effectiveness of water and salt community-based fluoridation methods in preventing dental caries among schoolchildren.

PubMed

Fabruccini, A; Alves, L S; Alvarez, L; Alvarez, R; Susin, C; Maltz, M

2016-12-01

To compare the effectiveness of water and salt community-based fluoridation methods on caries experience among schoolchildren. Data derived from two population-based oral health surveys of 12-year-old schoolchildren exposed to different community-based fluoridation methods were compared: artificially fluoridated water in Porto Alegre, South Brazil and artificially fluoridated salt in Montevideo, Uruguay. Data on socio-demographic characteristics, maternal education and oral hygiene were collected. Dental caries was defined according to the WHO criteria (cavitated lesions) and to the modified WHO criteria (active noncavitated lesions and cavitated ones). The association between community-based fluoridation methods and dental caries was modelled using logistic (caries prevalence) and Poisson regression (DMFT). Odds ratios (OR), rate ratios (RR), and the 95% confidence intervals (CI) were estimated. A total of 1528 in Porto Alegre and 1154 in Montevideo were examined (response rates: 83.2% and 69.6%, respectively). Adjusted estimates for caries prevalence and DMFT showed that schoolchildren from Porto Alegre were less affected by dental caries than their counterparts from Montevideo, irrespective of the criteria used. After adjusting for important characteristics, schoolchildren exposed to fluoridated salt had significantly higher likelihood of having caries (WHO criteria) than those exposed to fluoridated water (OR for prevalence=1.61, 95% CI=1.26-2.07; RR for DMFT=1.32, 95% CI=1.16-1.51). Similar differences were observed using the modified WHO criteria. Fluoridated water appears to provide a better protective effect against dental caries than fluoridated household salt among schoolchildren from developing countries. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Comparison of Fluoridated Miswak and Toothbrushing with Fluoridated Toothpaste on Plaque Removal and Fluoride Release.

PubMed

Baeshen, Hosam; Salahuddin, Sabin; Dam, Robel; Zawawi, Khalid H; Birkhed, Dowen

2017-04-01

Dental caries and periodontal diseases are all induced by oral biofilm (dental plaque). This study was conducted to evaluate if fluoride-impregnated miswak is as effective in plaque removal and fluoride release as toothbrushing with fluoride toothpaste. This single-blind, randomized, crossover study was conducted at the Department of Cariology, University of Gothenburg, Gothenburg, Sweden, from February 2010 to January 2011. Fifteen healthy subjects participated in this study. The participants were instructed to use the following: (1) 0.5% NaF-impregnated miswak, (2) nonfluoridated miswak, (3) toothbrush with nonfluoride toothpaste, and (4) toothbrush with 1450 ppm fluoride toothpaste. Each method was used twice a day for 1 week after which plaque amount and fluoride concentration in resting saliva were measured. There was a 1-week washout period between each method. No significant difference between miswak and tooth-brushing was found regarding plaque removal on buccal and lingual surfaces. A somewhat higher fluoride concentration in resting saliva was found after using impregnated miswak when compared with toothbrushing with fluoride toothpaste (p < 0.05). Miswak and toothbrushing showed the same plaque removing effect on buccal and lingual surfaces. Miswak impregnated with 0.5% NaF resulted in a higher concentration of fluoride in saliva than brushing with 1450 ppm fluoride toothpaste. Miswak impregnated with 0.5% NaF and toothbrushing results in comparable plaque removal and about the same fluoride concentration in saliva even it was somewhat higher for impregnated miswak.

COMPLEX FLUORIDES OF PLUTONIUM AND AN ALKALI METAL

DOEpatents

Seaborg, G.T.

1960-08-01

A method is given for precipitating alkali metal plutonium fluorides. such as KPuF/sub 5/, KPu/sub 2/F/sub 9/, NaPuF/sub 5/, and RbPuF/sub 5/, from an aqueous plutonium(IV) solution by adding hydrogen fluoride and alkali-metal- fluoride.

Chronologic Trends in Studies on Fluoride Mechanisms of Action.

PubMed

Oh, H J; Oh, H W; Lee, D W; Kim, C H; Ahn, J Y; Kim, Y; Shin, H B; Kim, C Y; Park, S H; Jeon, J G

2017-11-01

Fluoride has been widely used for the prevention of dental caries since the mid-20th century. The aim of this study was to investigate the chronologic trends in studies on fluoride mechanisms of action against dental caries during the years 1950 to 2015. To this aim, queries such as "fluoride," "fluoride and demineralization," "fluoride and remineralization," "fluoride and (plaque or biofilms)," and "fluoride and (bacteria or microbials)" were submitted to PubMed to collect research article information, including titles, abstracts, publication dates, author affiliations, and publication journals. The article information that PubMed produced was then collected by an automatic web crawler and examined through informetrics and linguistic analyses. We found that the number of articles concerned with fluoride mechanisms of action against dental caries was 6,903 and gradually increased over time during the years 1950 to 2015. They were published by 1,136 journals-most notably, Caries Research and Journal of Dental Research. Of the articles published, those related to bacteria/microbials had a higher percentage (44%) than those dealing with plaque/biofilms, demineralization, and remineralization. With regard to the geographic distribution of authors, Europe and North America accounted for 65% of the articles during the years 1987 to 2015, although the number of authors in Asia sharply increased in recent years. Among the fluoride compounds, NaF was mentioned more frequently than SnF 2 , Na 2 PO 3 F, amine fluoride, and acidulated phosphate fluoride during the years 1986 to 2015. Water fluoridation received the most attention among the various fluoride application methods (toothpastes, mouthwashes, fluoride varnishes, and fluoride gels) during the same period. These results, obtained from employing informetrics and linguistic analyses, suggest that in studies on fluoride mechanisms of action, 1) the unbalanced geographic distribution of articles and 2) the heavy concentration of articles on particular fluoride compounds and application methods should be overcome in future research.

Caries status in 16 year-olds with varying exposure to water fluoridation in Ireland.

PubMed

Mullen, J; McGaffin, J; Farvardin, N; Brightman, S; Haire, C; Freeman, R

2012-12-01

Most of the Republic of Ireland's public water supplies have been fluoridated since the mid-1960s while Northern Ireland has never been fluoridated, apart from some small short-lived schemes in east Ulster. This study examines dental caries status in 16 year-olds in a part of Ireland straddling fluoridated and non-fluoridated water supply areas and compares two methods of assessing the effectiveness of water fluoridation. The cross-sectional survey tested differences in caries status by two methods: 1, Estimated Fluoridation Status as used previously in national and regional studies in the Republic and in the All-Island study of 2002; 2, Percentage Lifetime Exposure, a modification of a system described by Slade in 1995 and used in Australian caries research. Adolescents were selected for the study by a two-part random sampling process. Firstly, schools were selected in each area by creating three tiers based on school size, and selecting schools randomly from each tier. Then random sampling of 16-year-olds from these schools, based on a pre-set sampling fraction for each tier of schools. With both systems of measurement, significantly lower caries levels were found in those children with the greatest exposure to fluoridated water when compared to those with the least exposure. The survey provides further evidence of the effectiveness in reducing dental caries experience up to 16 years of age. The extra intricacies involved in using the Percentage Lifetime Exposure method did not provide much more information when compared to the simpler Estimated Fluoridation Status method.

Copper Mediated Fluorination of Aryl Iodides

PubMed Central

Fier, Patrick S.; Hartwig, John F.

2012-01-01

The synthesis of aryl fluorides has been a topic of considerable interest because of the importance of aryl fluorides in pharmaceuticals, agrochemicals and materials. The stability, reactivity and biological properties of aryl fluorides can be distinct from those of the corresponding arenes. Methods for the synthesis of aryl fluorides, however, are limited. We report the conversion of a diverse set of aryl iodides to the corresponding aryl fluorides. This reaction occurs with a cationic copper reagent and silver fluoride. Preliminary results suggest this reaction is enabled by a facile reductive elimination from a cationic aryl copper(III) fluoride. PMID:22709145

Massachusetts Institute of Technology Lincoln Laboratory Facilities Replacement on Hanscom Air Force Base Phase 1 Final Environmental Assessment

DTIC Science & Technology

2014-07-24

Service UST Underground Storage Tank VC Vitrified Clay VOCs Volatile Organic Compounds W Watts 1 1.0 PURPOSE AND NEED FOR ACTION 1.1 INTRODUCTION The...discharged to sanitary drain and the solids slurry is hauled off site for disposal Fluoride drain: welded stainless steel drain piping from wet...diameter vitrified clay (VC) gravity sewer collection pipe, flowing north/northeast to the upper pumping station at Building 1306, is located within the

FUEL ELEMENT CONSTRUCTION

DOEpatents

Zumwalt, L.R.

1961-08-01

Fuel elements having a solid core of fissionable material encased in a cladding material are described. A conversion material is provided within the cladding to react with the fission products to form stable, relatively non- volatile compounds thereby minimizing the migration of the fission products into the coolant. The conversion material is preferably a metallic fluoride, such as lead difluoride, and may be in the form of a coating on the fuel core or interior of the cladding, or dispersed within the fuel core. (AEC)

Fluoride content of tank water in Australia.

PubMed

Cochrane, N J; Hopcraft, M S; Tong, A C; Thean, H l; Thum, Y S; Tong, D E; Wen, J; Zhao, S C; Stanton, D P; Yuan, Y; Shen, P; Reynolds, E C

2014-06-01

The aims of this study were to: (1) analyse the fluoride content of tank water; (2) determine whether the method of water collection or storage influenced fluoride content; and (3) survey participant attitudes towards water fluoridation. Plastic tubes and a questionnaire were distributed through dentists to households with water tanks in Victoria. A midstream tank water sample was collected and fluoride analysed in triplicate using ion chromatography All samples (n = 123) contained negligible amounts of fluoride, with a mean fluoride concentration of <0.01 ppm (range: <0.01-0.18 ppm). No statistically significant association was found between fluoride content and variables investigated such as tank material, tank age, roof material and gutter material. Most people did not know whether their tank water contained fluoride and 40.8% preferred to have access to fluoridated water. The majority thought fluoride was safe and more than half of the respondents supported fluoridation. Fluoride content of tank water was well below the optimal levels for caries prevention. People who rely solely on tank water for drinking may require additional exposure to fluoride for optimal caries prevention. © 2014 Australian Dental Association.

Detection of trace fluoride in serum and urine by online membrane-based distillation coupled with ion chromatography.

PubMed

Lou, Chaoyan; Guo, Dandan; Wang, Nani; Wu, Shuchao; Zhang, Peimin; Zhu, Yan

2017-06-02

An online membrane-based distillation (MBD) coupled with ion chromatography (IC) method was proposed for automatic detection of trace fluoride (F - ) in serum and urine samples. The system consisted of a sample vessel, a lab-made membrane module and an ion chromatograph. Hydrophobic polytetrafluoroethylene (PTFE) hollow fiber membrane was used in MBD which was directly performed in serum and urine samples to eliminate the matrix interferences and enrich fluoride, while enabling automation. The determination of fluoride in biological samples was carried out by IC with suppressed conductometric detection. The proposed method feasibly determined trace fluoride in serum and urine matrices with the optimized parameters, such as acid concentration, distillation temperature, and distillation time, etc. Fluoride exhibited satisfactory linearity in the range of 0.01-5.0mg/L with a correlation coefficient of 0.9992. The limit of detection (LOD, S/N=3) and limit of quantification (LOQ, S/N=10) were 0.78μg/L and 2.61μg/L, respectively. The relative standard deviations of peak area and peak height were all less than 5.15%. The developed method was validated for the determination of fluoride in serum and urine with good spiked recoveries ranging between 97.1-101.9%. This method also can be proposed as a suitable alternative for the analysis of fluoride in other complex biological samples. Copyright © 2017. Published by Elsevier B.V.

76 FR 2383 - Proposed HHS Recommendation for Fluoride Concentration in Drinking Water for Prevention of Dental...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-13

... information: Community water fluoridation is the most cost-effective method of delivering fluoride for the... Drinking Water for Prevention of Dental Caries AGENCY: Office of the Secretary, Department of Health and.... The U.S. Public Health Service recommendations for optimal fluoride concentrations were based on...

Ion release from, and fluoride recharge of a composite with a fluoride-containing bioactive glass.

PubMed

Davis, Harry B; Gwinner, Fernanda; Mitchell, John C; Ferracane, Jack L

2014-10-01

Materials that are capable of releasing ions such as calcium and fluoride, that are necessary for remineralization of dentin and enamel, have been the topic of intensive research for many years. The source of calcium has most often been some form of calcium phosphate, and that for fluoride has been one of several metal fluoride or hexafluorophosphate salts. Fluoride-containing bioactive glass (BAG) prepared by the sol-gel method acts as a single source of both calcium and fluoride ions in aqueous solutions. The objective of this investigation was to determine if BAG, when added to a composite formulation, can be used as a single source for calcium and fluoride ion release over an extended time period, and to determine if the BAG-containing composite can be recharged upon exposure to a solution of 5000ppm fluoride. BAG 61 (61% Si; 31% Ca; 4% P; 3% F; 1% B) and BAG 81 (81% Si; 11% Ca; 4% P; 3% F; 1% B) were synthesized by the sol-gel method. The composite used was composed of 50/50 Bis-GMA/TEGDMA, 0.8% EDMAB, 0.4% CQ, and 0.05% BHT, combined with a mixture of BAG (15%) and strontium glass (85%) to a total filler load of 72% by weight. Disks were prepared, allowed to age for 24h, abraded, then placed into DI water. Calcium and fluoride release was measured by atomic absorption spectroscopy and fluoride ion selective electrode methods, respectively, after 2, 22, and 222h. The composite samples were then soaked for 5min in an aqueous 5000ppm fluoride solution, after which calcium and fluoride release was again measured at 2, 22, and 222h time points. Prior to fluoride recharge, release of fluoride ions was similar for the BAG 61 and BAG 81 composites after 2h, and also similar after 22h. At the four subsequent time points, one prior to, and three following fluoride recharge, the BAG 81 composite released significantly more fluoride ions (p<0.05). Both composites were recharged by exposure to 5000ppm fluoride, although the BAG 81 composite was recharged more than the BAG 61 composite. The BAG 61 composite released substantially more calcium ions prior to fluoride recharge during each of the 2 and 22h time periods. Thereafter, the release of calcium at the four subsequent time points was not significantly different (p>0.05) for the two composites. These results show that, when added to a composite formulation, fluoride-containing bioactive glass made by the sol-gel route can function as a single source for both calcium and fluoride ions, and that the composite can be readily recharged with fluoride. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Low temperature route to uranium nitride

DOEpatents

Burrell, Anthony K.; Sattelberger, Alfred P.; Yeamans, Charles; Hartmann, Thomas; Silva, G. W. Chinthaka; Cerefice, Gary; Czerwinski, Kenneth R.

2009-09-01

A method of preparing an actinide nitride fuel for nuclear reactors is provided. The method comprises the steps of a) providing at least one actinide oxide and optionally zirconium oxide; b) mixing the oxide with a source of hydrogen fluoride for a period of time and at a temperature sufficient to convert the oxide to a fluoride salt; c) heating the fluoride salt to remove water; d) heating the fluoride salt in a nitrogen atmosphere for a period of time and at a temperature sufficient to convert the fluorides to nitrides; and e) heating the nitrides under vacuum and/or inert atmosphere for a period of time sufficient to convert the nitrides to mononitrides.

[Effect of fluoride on human hypothalamus-hypophysis-testis axis hormones].

PubMed

Hao, Pengfei; Ma, Xiaoying; Cheng, Xuemin; Ba, Yue; Zhu, Jingyuan; Cui, Liuxin

2010-01-01

To study of endocrine disturbing effect of fluoride on human hypothalamus-hypophysis-testis axis hormones. Sunying County, Kaifeng City was selected as polluted district which the fluoride in drinking water was 3.89 mg/L, and Shenlilou county was selected as control district which the fluoride was less than 1.0 mg/L. 150 individual lived there more than 5 years were srlected randomly. And investigated by medical examination, then blood and urine sample were collected, and the serum level of gonadotropin-releasing hormone (GnRH), luteinizing hormone (LH), testosterone (T) and estradiol (E2) were measured by RIA method, and the urine level of fluoride were measured. Other than that, the concentration of fluoride in the water, food, soil and air were detected by the standard methods. The concentrations of fluoride in the water, food and soil of the fluoride polluted district were significantly higher than those of control district (P < 0.05), and the concentration fluoride in the air of two district were not found. There was no significant difference of serum level of GnRH between fluoride polluted district and control district (P > 0.05). The serum level of LH in men of fluoride polluted district was significantly higher than that of control group (P < 0.05), and the serum level of T in men of fluoride polluted district was significantly less than that of control group (P < 0.05). There was no significant difference of serum level of LH between fluoride polluted district and control district (P > 0.05), and the serum level of T in women of fluoride polluted district was significantly higher than that of control group (P < 0.05). There was no significant difference of serum level of E2 between fluoride polluted district and control district (P > 0.05). Fluoride could effect hormone levels of each layer of the hypothalamus-hypophysis-testis axis, and show the reproductive endocrine disturbing effects. The reproductive endocrine disturbing effects of male maybe more severe than those of female.

Improving Dental Health of DOD Related Persons Assigned to Okinawa by Using Fluoridated Salt in Lieu of Water Fluoridation: A Comparative Analysis

DTIC Science & Technology

1999-04-01

1994-1997). During this time, the 18th Medical Group (MDG) set fluoridating the base water supply as a goal to prevent dental caries – a noble and...related personnel. Supplemental fluoride may be an effective method of improving oral health by reducing dental caries . Water and salt fluoridation ...372-5,381. 9 Colonel Canning and Mr. Noorda, “Talking Paper on Fluoridation of Kadena AB Drinking Water ,” 26 Apr 1995. 5 Chapter 2 Dental Caries The

Fluoride intake of infants living in non-fluoridated and fluoridated areas.

PubMed

Zohoori, F V; Whaley, G; Moynihan, P J; Maguire, A

2014-01-01

Data on fluoride exposure of infants are sparse. This study aimed to estimate total daily fluoride intake (TDFI) of infants aged 1-12 months, living in non-fluoridated and fluoridated areas in north-east England. Daily dietary fluoride intake was assessed using a three-day food diary coupled with analysis of fluoride content of food/drink consumed, using a F-ISE and diffusion method. A questionnaire with an interview was used to collect information on toothbrushing habits. TDFI was estimated from diet, plus fluoride supplements and dentifrice ingestion where used. Thirty-eight infants completed the study; 19 receiving fluoridated water (mean 0.97 mgF/l) and 19 receiving non-fluoridated water (mean 0.19 mgF/l). Mean (SD) TDFI for the infants living in fluoridated and non-fluoridated areas was 0.107 (0.054) and 0.024 (0.015) mg/kg body weight per day, respectively. Diet was the only fluoride source for 87% of infants and none used fluoride supplements. For infants for whom mouth/teeth cleaning was undertaken, dentifrice contribution to TDFI ranged from 24 to 78%. Infants living in fluoridated areas, in general, may receive a fluoride intake, from diet only, of more than the suggested optimal range for TDFI. This emphasises the importance of estimating TDFI at an individual level when recommendations for fluoride use are being considered.

Association between estimated fluoride intake and dental caries prevalence among 5-year-old children in Korea.

PubMed

Kim, Min-Ji; Kim, Han-Na; Jun, Eun-Joo; Ha, Jung-Eun; Han, Dong-Hun; Kim, Jin-Bom

2015-12-30

The purposes of this study were to estimate the fluoride intake from food and drink in 5-year-old Korean children, and to measure the association between estimated fluoride intake and dental caries prevalence. The study involved a secondary analysis of raw data from the 4(th) Korea National Health and Nutrition Examination Survey (KNHANES; 2007-2009). The study subjects were 167 boys and 147 girls aged 5 years who had undergone both physical and nutritional examination as part of the survey. The KNHANES comprised a health questionnaire, a physical examination, and a nutritional examination. The nutritional examination of KNHANES consisted of 3 parts: a dietary life survey, a food-frequency questionnaire, and a food intake investigation. The food intake investigation used the 24-h recall method, with information being provided by the children's parents. On the basis of this information, we evaluated the fluoride content in a total of 310 food items using the hexamethyldisiloxane (HMDS)-facilitated diffusion method, modified using Taves' microdiffusion method. As part of the KNHANES survey, oral examinations were conducted at a mobile examination centre by trained dentists using dental mirrors under a fluorescent light. These examinations were performed using methods proposed by the World Health Organization. The dietary fluoride intake of 5-year-old Korean children was estimated to be 0.35 mg/day, or 0.016 mg/kg/day. The "decayed or filled surfaces" (dfs) indices of primary teeth were higher in children who had a lower dietary intake of fluoride. There was a significant inverse association between dietary fluoride intake and the prevalence of dental caries. The inverse association between dietary fluoride intake levels and prevalence of dental caries implies that the introduction of community caries prevention programmes may be beneficial. Such programmes would include water fluoridation and a fluoride supplementation programme.

Data on fluoride concentration level in villages of Asara (Alborz, Iran) and daily fluoride intake based on drinking water consumption.

PubMed

Akhavan, Giti; Dobaradaran, Sina; Borazjani, Jaleh Mohajeri

2016-12-01

In the present data article, fluoride concentration levels of drinking water (with spring or groundwater sources) in 10 villages of Asara area located in Alborz province were determined by the standard SPADNS method using a spectrophotometer (DR/2000 Spectrophotometer, USA). Daily fluoride intakes were also calculated based on daily drinking water consumption. The fluoride content were compared with EPA and WHO guidelines for drinking water.

Association between Urine Fluoride and Dental Fluorosis as a Toxicity Factor in a Rural Community in the State of San Luis Potosi

PubMed Central

Jarquín-Yañez, Lizet; Mejía-Saavedra, José de Jesús; Molina-Frechero, Nelly; Gaona, Enrique; Rocha-Amador, Diana Olivia; López-Guzmán, Olga Dania; Bologna-Molina, Ronell

2015-01-01

Objective. The aim of this study is to investigate urine fluoride concentration as a toxicity factor in a rural community in the state of San Luis Potosi, Mexico. Materials and Methods. A sample of 111 children exposed to high concentrations of fluoride in drinking water (4.13 mg/L) was evaluated. Fluoride exposure was determined by measuring urine fluoride concentration using the potentiometric method with an ion selective electrode. The diagnosis of dental fluorosis was performed by clinical examination, and the severity of damage was determined using Dean's index and the Thylstrup-Fejerskov (TF) index. Results. The range of exposure in the study population, evaluated through the fluoride content in urine, was 1.1 to 5.9 mg/L, with a mean of 3.14 ± 1.09 mg/L. Dental fluorosis was present in all subjects, of which 95% had severe cases. Higher urine fluoride levels and greater degrees of severity occurred in older children. Conclusions. The results show that dental fluorosis was determined by the presence of fluoride exposure finding a high positive correlation between the severity of fluorosis and urine fluoride concentration and the years of exposure suggested a cumulative effect. PMID:25789336

Dissolution of bulk specimens of silicon nitride

NASA Technical Reports Server (NTRS)

Davis, W. F.; Merkle, E. J.

1981-01-01

An accurate chemical characterization of silicon nitride has become important in connection with current efforts to incorporate components of this material into advanced heat engines. However, there are problems concerning a chemical analysis of bulk silicon nitride. Current analytical methods require the pulverization of bulk specimens. A pulverization procedure making use of grinding media, on the other hand, will introduce contaminants. A description is given of a dissolution procedure which overcomes these difficulties. It has been found that up to at least 0.6 g solid pieces of various samples of hot pressed and reaction bonded silicon nitride can be decomposed in a mixture of 3 mL hydrofluoric acid and 1 mL nitric acid overnight at 150 C in a Parr bomb. High-purity silicon nitride is completely soluble in nitric acid after treatment in the bomb. Following decomposition, silicon and hydrofluoric acid are volatilized and insoluble fluorides are converted to a soluble form.

WO3 and W Thermal Atomic Layer Etching Using "Conversion-Fluorination" and "Oxidation-Conversion-Fluorination" Mechanisms.

PubMed

Johnson, Nicholas R; George, Steven M

2017-10-04

The thermal atomic layer etching (ALE) of WO 3 and W was demonstrated with new "conversion-fluorination" and "oxidation-conversion-fluorination" etching mechanisms. Both of these mechanisms are based on sequential, self-limiting reactions. WO 3 ALE was achieved by a "conversion-fluorination" mechanism using an AB exposure sequence with boron trichloride (BCl 3 ) and hydrogen fluoride (HF). BCl 3 converts the WO 3 surface to a B 2 O 3 layer while forming volatile WO x Cl y products. Subsequently, HF spontaneously etches the B 2 O 3 layer producing volatile BF 3 and H 2 O products. In situ spectroscopic ellipsometry (SE) studies determined that the BCl 3 and HF reactions were self-limiting versus exposure. The WO 3 ALE etch rates increased with temperature from 0.55 Å/cycle at 128 °C to 4.19 Å/cycle at 207 °C. W served as an etch stop because BCl 3 and HF could not etch the underlying W film. W ALE was performed using a three-step "oxidation-conversion-fluorination" mechanism. In this ABC exposure sequence, the W surface is first oxidized to a WO 3 layer using O 2 /O 3 . Subsequently, the WO 3 layer is etched with BCl 3 and HF. SE could simultaneously monitor the W and WO 3 thicknesses and conversion of W to WO 3 . SE measurements showed that the W film thickness decreased linearly with number of ABC reaction cycles. W ALE was shown to be self-limiting with respect to each reaction in the ABC process. The etch rate for W ALE was ∼2.5 Å/cycle at 207 °C. An oxide thickness of ∼20 Å remained after W ALE, but could be removed by sequential BCl 3 and HF exposures without affecting the W layer. These new etching mechanisms will enable the thermal ALE of a variety of additional metal materials including those that have volatile metal fluorides.

Genesis of kasolite associated with aplite-pegmatite at Jabal Sayid, Hijaz region, Kingdom of Saudi Arabia

NASA Astrophysics Data System (ADS)

Dawood, Yehia H.; Harbi, Hesham M.; Abd El-Naby, Hamdy H.

2010-01-01

In this study, we report kasolite Pb(UO 2)SiO 4·(H 2O) for the first time as a main uranyl mineral in the mineralized aplite-pegmatite of Jabal Sayid, Hijaz region. It commonly forms clusters of yellow acicular crystals in the voids and fractures. The mineral chemistry and mineralogical characteristics of kasolite were investigated using different techniques. Calcium, iron and phosphorus are detected in kasolite in addition to its major constituents; uranium, lead and silicon. Lead does not exist as a radiogenic product and not even as a substitute for uranium in the mineral structure. Alternatively, galena mineralization could be considered as a source for lead. The fluoride and carbonate complexes played a significant role in the formation of kasolite. High temperature hydrothermal solutions reacted with pre-existing uranium-bearing metamictized accessory minerals such as pyrochlore, U-rich thorite and zircon to form uranous fluoride complexes. These complexes are predominant in reducing environment and at pH 4. When the fluids approached the surface passing through fracture system, the oxygen fugacity ( fO 2) and the pH increased because of the loss of volatile components. At these conditions, uranous fluorides would convert to uranyl fluoride complexes UO 2F 3-. Further decrease in temperature was associated with the decay of the activity of fluorine ion by the dilution of hydrothermal solutions and precipitation of fluorite. At this condition, uranyl-carbonate complexes are favoured. These complexes were combined later with silica and lead to form kasolite.

Fluoride toothpastes and fluoride mouthrinses for home use.

PubMed

Rugg-Gunn, Andrew; Bánóczy, Jolán

2013-11-01

To provide a brief commentary review of fluoride-containing toothpastes and mouthrinses with emphasis on their use at home. Toothpastes and mouthrinses are just two of many ways of providing fluoride for the prevention of dental caries. The first investigations into incorporating fluoride into toothpastes and mouthrinses were reported in the middle 1940s. Unlike water fluoridation (which is 'automatic fluoridation'), fluoride-containing toothpastes and fluoridecontaining mouthrinses are, primarily, for home use and need to be purchased by the individual. By the 1960s, research indicated that fluoride could be successfully incorporated into toothpastes and clinical trials demonstrated their effectiveness. By the end of the 1970s, almost all toothpastes contained fluoride. The widespread use of fluoride- containing toothpastes is thought to be the main reason for much improved oral health in many countries. Of the many fluoride compounds investigated, sodium fluoride, with a compatible abrasive, is the most popular, although amine fluorides are used widely in Europe. The situation is similar for mouthrinses. Concentrations of fluoride (F), commonly found, are 1500 ppm (1500 μg F/g) for toothpastes and 225 ppm (225 μg F/ml) for mouthrinse. Several systematic reviews have concluded that fluoride-containing toothpastes and mouthrinses are effective, and that there is added benefit from their use with other fluoride delivery methods such as water fluoridation. Guidelines for the appropriate use of fluoride toothpastes and mouthrinses are available in many countries. Fluoride toothpastes and mouthrinses have been developed and extensive testing has demonstrated that they are effective and their use should be encouraged. Copyright © 2013 by Academy of Sciences and Arts of Bosnia and Herzegovina.

Correlation between Fluoride in Drinking Water and Its Levels in Breast Milk in Golestan Province, Northern Iran

PubMed Central

FARAJI, Hossein; MOHAMMADI, Ali Akbar; AKBARI-ADERGANI, Behrouz; VAKILI SAATLOO, Naimeh; LASHKARBOLOKI, Gholamreza; MAHVI, Amir Hossein

2014-01-01

Background: Fluoride is an essential element for human health. However, excess fluoride in drinking water may cause dental and/or skeletal fluorosis. Drinking water is the main route of fluoride intake. The aim of the present study was to measure fluoride levels in human breast milk collected from two regions of Golestan Province, northern Iran with different amount of fluoride concentration of drinking water in Bandar Gaz and Nokande cities and to correlate it with fluoride concentrations in drinking water used by mothers living in these two areas. Methods: Twenty samples of water were collected from seven drinking water wells during 2012 from Bandar Gaz and Nokande in Iran during 2012. Fluoride concentration of water samples was measured using SPADNS method. Sixty breast milk samples were collected from lactating mothers of Bandar Gaz and Nokande cities. Content in breast milk was determined using standard F ion-selective electrode. Spearman’s rho correlation analysis was used to assess any possible relationship between fluoride levels in breast milk and in drinking water. Results: The means and standard deviation for F concentration in breast milk and drinking water were 0.002188±0.00026224 ppm and 0.5850±0.22542 ppm, respectively. Analysis of data showed that the variables were not normally distributed so the Spearman correlation coefficient between two variables calculated (ρS = 0.65) and it was significant (P=0.002). Conclusion: Fluoride concentration in water can directly act on its concentration in breast milk. We speculate that modifying F concentration in water can affect accessibility of fluoride for infants. PMID:26171359

Is the fluoride intake by diet and toothpaste in children living in tropical semi-arid city safe?

PubMed

Oliveira, Priscila Ferreira Torres de; Cury, Jaime Aparecido; Lima, Carolina Veloso; Vale, Glauber Campos; Lima, Marina de Deus Moura de; Moura, Lúcia de Fátima Almeida de Deus; Moura, Marcoeli Silva de

2018-01-01

Data about total fluoride intake in children living in a tropical semi-arid climate city is scarce, thus we conducted this study. Fifty-eight children aged two to five years, living in a Brazilian tropical city with optimally fluoridated water were selected. Dietary samples were collected using the duplicate diet method on two non-consecutive days in the children's home toothpaste was determined by subtracting the amount of fluoride recovered after brushing from the amount placed on the toothbrush. The mean total dose (SD) of fluoride intake was 0.043(0.016) mg F·kg-1·d-1, with the major (60.6%) contribution from water. The factors associated with the ingestion of fluoride from toothpaste were fluoride concentration of the toothpaste (p = 0.03) and the use of kids toothpaste (p = 0.02). The findings suggest that children have a low fluoride intake, measured by at-home meals and use of fluoride toothpaste; drinking water is the main source of fluoride ingestion.

[Influence of chronic fluorosis on the expression of mitochondrial fission protein dynamin-related 1 in the cortical neurons of rats].

PubMed

Lou, Di-dong; Zhang, Kai-lin; Pan, Ji-gang; Qin, Shuang-li; Liu, Yan-fei; Yu, Yan-ni; Guan, Zhi-zhong

2013-06-01

To explore the changes of protein expression of mitochondrial fission gene dynamin-related 1(Drp 1) in the cortical neurons of rats with chronic fluorosis. A total of 120 one-month-old SD rats (each weighing approximately 100-120 g at the beginning of the experiment) were randomly divided into three groups, and fed with the different doses of fluoride containing in drinking water (untreated control containing 0 mg/L fluoride, and low-fluoride & high-fluoride supplemented with 10 and 50 mg/L fluoride,respectively). After 3 or 6 months exposure, 20 rats from each group were killed. Then the protein expression of mitochondrial fission gene, Drp1, was detected by immunohistochemistry and western-blotting method. Dental fluorosis and urinary fluorosis were obviously found in the rats exposed to fluoride. At the experiment period of 3 months, the numbers of positive cells of Drp1 detected by immunohistochemistry changed. Compared with the control group (36.3 ± 5.8), the changes in low-fluoride group (34.7 ± 4.1) showed no significant difference (t = 1.5, P > 0.05),but the increase in high-fluoride group (45.0 ± 4.7) had statistical significance (t = 8.8, P < 0.05). The western-blotting method had consistent results. Compared with the control group (0.59 ± 0.03), a significant increase of the average topical density in low- fluoride (0.62 ± 0.03) and high-fluoride (0.71 ± 0.02) groups were found (t = 0.02,0.11, P < 0.05). At the experiment period of 6 months, the numbers of positive cells of Drp1 detected by immunohistochemistry significantly changed. Compared with the control group (33.2 ± 4.4), the number in low- fluoride and high-fluoride groups were separately (36.6 ± 3.8) and (39.4 ± 4.2),both increased significantly (t = 3.5,6.3, P < 0.05). Same results could be found in western-blotting method,compared with the control group (0.65 ± 0.06), the average topical density in low- fluoride (0.80 ± 0.09) and high-fluoride (0.76 ± 0.08) groups both increased significantly (t = 0.1,0.1, P < 0.05). Taking excessive amount of fluoride might result in the changes of expression of Drp1, and the neurons damage from the chronic fluorosis might be associated with the hyperfunction of mitochondrial fusion.

On the assessment of hydroxyapatite fluoridation by means of Raman scattering

NASA Astrophysics Data System (ADS)

Campillo, M.; Lacharmoise, P. D.; Reparaz, J. S.; Goñi, A. R.; Valiente, M.

2010-06-01

Hydroxyapatite is the main mineral component of bones and teeth. Fluorapatite, a bioceramic that can be obtained from hydroxyapatite by chemical substitution of the hydroxide ions with fluoride, exhibits lower mineral solubility and larger mechanical strength. Despite the widespread use of fluoride against caries, a reliable technique for unambiguous assessment of fluoridation in in vitro tests is still lacking. Here we present a method to probe fluorapatite formation in fluoridated hydroxyapatite by combining Raman scattering with thermal annealing. In synthetic minerals, we found that effectively fluoride substituted hydroxyapatite transforms into fluorapatite only after heat treatment, due to the high activation energy for this first order phase transition.

SEPARATION OF PLUTONIUM

DOEpatents

Maddock, A.G.; Smith, F.

1959-08-25

A method is described for separating plutonium from uranium and fission products by treating a nitrate solution of fission products, uranium, and hexavalent plutonium with a relatively water-insoluble fluoride to adsorb fission products on the fluoride, treating the residual solution with a reducing agent for plutonium to reduce its valence to four and less, treating the reduced plutonium solution with a relatively insoluble fluoride to adsorb the plutonium on the fluoride, removing the solution, and subsequently treating the fluoride with its adsorbed plutonium with a concentrated aqueous solution of at least one of a group consisting of aluminum nitrate, ferric nitrate, and manganous nitrate to remove the plutonium from the fluoride.

Anomalous piezoelectric properties of poly(vinylidene fluoride-trifluoroethylene)/ionic liquid gels

NASA Astrophysics Data System (ADS)

Fukagawa, Miki; Koshiba, Yasuko; Fukushima, Tatsuya; Morimoto, Masahiro; Ishida, Kenji

2018-04-01

Piezoelectric gels were prepared from low-volatile ionic liquid (IL) 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([Emim][TFSI]) gels, and their structural, ferroelectric, and piezoelectric properties were investigated. Poly(vinylidene fluoride-trifluoroethylene) P(VDF-TrFE)/IL gels were formed using thermally reversible physical gels. The structural characterization indicated that the P(VDF-TrFE) molecules in the gels predominantly formed a ferroelectric phase (Form I) of P(VDF-TrFE). Polarization switching peaks were clearly observed using a three-layer stacked device structure. The coercive field of the P(VDF-TrFE)/IL gels substantially decreased to 4-9 MV/m, and their remnant polarizations were maintained at 63-71 mC/m2, which is similar to that for typical solid-state P(VDF-TrFE). Finally, the P(VDF-TrFE)/IL gel films exhibited a piezoelectric response, and the highest piezoelectric coefficient was ˜300 pm/V at an applied voltage frequency of 4 kHz.

Thermochemical characterization of some thermoplastic materials. [flammability and toxicity properties for aircraft interiors

NASA Technical Reports Server (NTRS)

Kourtides, D. A.; Parker, J. A.; Hilado, C. J.

1977-01-01

The thermochemical and flammability characteristics of some typical thermoplastic materials currently in use or being considered for use in aircraft interiors are described. The properties studied included thermomechanical properties such as glass-transition and melt temperature, changes in polymer enthalpy, thermogravimetric analysis in anerobic and oxidative environments, oxygen index, smoke evolution, relative toxicity of the volatile products of pyrolysis, and selected physical properties. The generic polymers evaluated included acrylonitrile butadiene styrene, bisphenol A polycarbonate, 9,9 bis (4-hydroxyphenyl) fluorene polycarbonate-poly (dimethylsiloxane) block polymer, phenolphthalein-bisphenol A polycarbonate, phenolphthalein polycarbonate, polyether sulfone, polyphenylene oxide, polyphenylene sulfide, polyaryl sulfone, chlorinated polyvinyl chloride homopolymer, polyvinyl fluoride, and polyvinylidene fluoride. Processing parameters, including molding characteristics of some of the advanced polymers, are described. Test results and relative rankings of some of the flammability, smoke, and toxicity properties are presented. Under these test conditions, some of the advanced polymers evaluated were significantly less flammable and toxic than or equivalent to polymers in current use.

Method for dissolving plutonium dioxide

DOEpatents

Tallent, Othar K.

1978-01-01

The fluoride-catalyzed, non-oxidative dissolution of plutonium dioxide in HNO.sub.3 is significantly enhanced in rate by oxidizing dissolved plutonium ions. It is believed that the oxidation of dissolved plutonium releases fluoride ions from a soluble plutonium-fluoride complex for further catalytic action.

The effect of a mouthrinse containing chlorine dioxide in the clinical reduction of volatile sulfur compounds.

PubMed

Soares, Leo Guimaraes; Guaitolini, Roberto Luiz; Weyne, Sergio de Carvalho; Falabella, Marcio Eduardo Vieira; Tinoco, Eduardo Muniz Barretto; da Silva, Denise Gomes

2013-07-01

This study sought to evaluate the clinical effect of a mouthrinse containing 0.3% chlorine dioxide (ClO2) in reducing oral volatile sulfur compounds (VSC). Halitosis was induced by L-cysteine in 11 volunteers, and 4 solutions were compared: a test solution containing 0.3% ClO2, 0.07% cetylpyridinium chloride (CPC), and 0.05% sodium fluoride; a placebo; a solution containing 0.05% CPC; and a control solution of 0.2% chlorhexidine gluconate (CHX). VSC levels were assessed using a Halimeter, and 6 measurements were made from baseline to 3 hours postrinse. The VSC reduction rate of the test mouthrinse was superior to the placebo and the CPC solution. There was no difference between the test solution and the CHX solution in VSC reduction rates immediately postrinse, or at 2 and 3 hours postrinse; both solutions were statistically superior to the placebo and the CPC solution.

Effects of land use on water quality of the Fountain Creek alluvial aquifer, east-central Colorado

USGS Publications Warehouse

Chafin, Daniel T.

1996-01-01

Water-quality data were collected from the Fountain Creek alluvial aquifer in 1988 and 1989 as part of the Toxic-Waste Ground-Water Contamination Program. These data indicate that dissolved solids, most major ions, fluoride, ammonium, boron, lithium, selenium, and strontium were more concentrated in the agricultural land-use area than in the upgradient urban land-use area. Nitrate and phosphate had significantly larger concentrations, and volatile organic compounds had significantly greater detection frequencies in the urban land-use area.

A Review on Adsorption of Fluoride from Aqueous Solution

PubMed Central

Habuda-Stanić, Mirna; Ergović Ravančić, Maja; Flanagan, Andrew

2014-01-01

Fluoride is one of the anionic contaminants which is found in excess in surface or groundwater because of geochemical reactions or anthropogenic activities such as the disposal of industrial wastewaters. Among various methods used for defluoridation of water such as coagulation, precipitation, membrane processes, electrolytic treatment, ion-exchange, the adsorption process is widely used. It offers satisfactory results and seems to be a more attractive method for the removal of fluoride in terms of cost, simplicity of design and operation. Various conventional and non-conventional adsorbents have been assessed for the removal of fluoride from water. In this review, a list of various adsorbents (oxides and hydroxides, biosorbents, geomaterials, carbonaceous materials and industrial products and by-products) and its modifications from literature are surveyed and their adsorption capacities under various conditions are compared. The effect of other impurities on fluoride removal has also been discussed. This survey showed that various adsorbents, especially binary and trimetal oxides and hydroxides, have good potential for the fluoride removal from aquatic environments. PMID:28788194

Black Tea Source, Production, and Consumption: Assessment of Health Risks of Fluoride Intake in New Zealand

PubMed Central

Godfrey, Michael; Limeback, Hardy

2017-01-01

In countries with fluoridation of public water, it is imperative to determine other dietary sources of fluoride intake to reduce the public health risk of chronic exposure. New Zealand has one of the highest per capita consumption rates of black tea internationally and is one of the few countries to artificially fluoridate public water; yet no information is available to consumers on the fluoride levels in tea products. In this study, we determined the contribution of black tea as a source of dietary fluoride intake by measuring the fluoride content in 18 brands of commercially available products in New Zealand. Fluoride concentrations were measured by potentiometric method with a fluoride ion-selective electrode and the contribution of black tea to Adequate Intake (AI) and Tolerable Upper Intake Level (UL) was calculated for a range of consumption scenarios. We examined factors that influence the fluoride content in manufactured tea and tea infusions, as well as temporal changes in fluoride exposure from black tea. We review the international evidence regarding chronic fluoride intake and its association with chronic pain, arthritic disease, and musculoskeletal disorders and provide insights into possible association between fluoride intake and the high prevalence of these disorders in New Zealand. PMID:28713433

Intra-oral models to assess cariogenicity: evaluation of oral fluoride and pH.

PubMed

Duckworth, R M; Gilbert, R J

1992-04-01

The main purpose of this paper is to review the various methods used for evaluation of fluoride retention in saliva, plaque, and enamel following application of topical anti-caries treatments such as F dentifrices and F mouthwashes. Such methods monitor delivery of fluoride to the site of action, the mouth, and so can be regarded as assessing potential for treatment action. It is concluded that intra-oral fluoride measurements are appropriate to support bioequivalence claims for anti-caries treatments, provided that particular chosen methods have been calibrated against clinical data. Studies purporting to show superiority are of interest mechanistically, but links to caries are not sufficiently understood to define superiority claims. A wide variety of methods has been used for determination of the fluoride content of enamel. Of these, well-established methods such as the micro-drill and acid-etch procedures are appropriate for routine comparative testing, whereas sophisticated instrumental techniques such as SIMS are more appropriate for detailed mechanistic studies. Intra-oral pH measurements are also relevant to many topical treatments. Single-site determinations in plaque are preferred, but for comparative studies non-specific determinations may be adequate.

Focus on Fluorides: Update on the Use of Fluoride for the Prevention of Dental Caries

PubMed Central

Carey, Clifton M.

2014-01-01

Declarative Title: Improving the efficacy of fluoride therapies reduces dental caries and lowers fluoride exposure. Background Fluoride is delivered to the teeth systemically or topically to aid in the prevention of dental caries. Systemic fluoride from ingested sources is in blood serum and can be deposited only in teeth that are forming in children. Topical fluoride is from sources such as community water, processed foods, beverages, toothpastes, mouthrinses, gels, foams, and varnishes. The United States Centers for Disease Control and Prevention (CDC) and the American Dental Association (ADA) have proposed changes in their long standing recommendations for the amount of fluoride in community drinking water in response to concerns about an increasing incidence of dental fluorosis in children. Current research is focused on the development of strategies to improve fluoride efficacy. The purpose of this update is to inform the reader about new research and policies related to the use of fluoride for the prevention of dental caries. Methods Reviews of the current research and recent evidence based systematic reviews on the topics of fluoride are presented. Topics discussed include: updates on community water fluoridation research and policies; available fluoride in dentifrices; fluoride varnish compositions, use, and recommendations; and other fluoride containing dental products. This update provides insights into current research and discusses proposed policy changes for the use of fluoride for the prevention of dental caries. Conclusions The dental profession is adjusting their recommendations for fluoride use based on current observations of the halo effect and subsequent outcomes. The research community is focused on improving the efficacy of fluoride therapies thus reducing dental caries and lowering the amount of fluoride required for efficacy. PMID:24929594

Methods of decontaminating surfaces and related compositions

DOEpatents

Demmer, Ricky L.; Crosby, Daniel; Norton, Christopher J.

2016-11-22

A composition of matter includes water, at least one acid, at least one surfactant, at least one fluoride salt, and ammonium nitrate. A method of decontaminating a surface includes exposing a surface to such a composition and removing the composition from the surface. Other compositions of matter include water, a fatty alcohol ether sulfate, nitrilotriacetic acid, at least one of hydrochloric acid and nitric acid, sodium fluoride, potassium fluoride, ammonium nitrate, and gelatin.

Fluoride Ion Regeneration of Cyclosarin (Gf) from Minipig Tissue and Fluids Following Whole Body GF Vapor Exposure

DTIC Science & Technology

2006-11-01

Quantitation of organophosphorus nerve agent metabolites in human urine using isotope dilution gas chromatography- tandem mass spectrometry. J. Anal...Recent developments to improve nerve agent biomarker techniques include methods for measuring fluoride regenerated Sarin (GB) in blood and tissue...Our efforts extend the fluoride ion regeneration method to be able to determine cyclosarin (GF) in red blood cells, plasma, and tissue of minipig

Milk fluoridation for the prevention of dental caries.

PubMed

Bánóczy, Jolán; Rugg-Gunn, Andrew; Woodward, Margaret

2013-11-01

The aim of this review is to give an overview of 55 years experience of milk fluoridation and draw conclusions about the applicability of the method. Fluoridated milk was first investigated in the early 1950s, almost simultaneously in Switzerland, the USA and Japan. Stimulated by the favourable results obtained from these early studies, the establishment of The Borrow Dental Milk Foundation (subsequently The Borrow Foundation) in England gave an excellent opportunity for further research, both clinical and non-clinical, and a productive collaboration with the World Health Organization which began in the early 1980s. Numerous peer-reviewed publications in international journals showed clearly the bioavailability of fluoride in various types of milk. Clinical trials were initiated in the 1980s - some of these can be classed as randomised controlled trials, while most of the clinical studies were community preventive programmes. These evaluations showed clearly that the optimal daily intake of fluoride in milk is effective in preventing dental caries. The amount of fluoride added to milk depends on background fluoride exposure and age of the children: commonly in the range 0.5 to 1.0 mg per day. An advantage of the method is that a precise amount of fluoride can be delivered under controlled conditions. The cost of milk fluoridation programmes is low, about € 2 to 3 per child per year. Fluoridation of milk can be recommended as a caries preventive measure where the fluoride concentration in drinking water is suboptimal, caries experience in children is significant, and there is an existing school milk programme. Copyright © 2013 by Academy of Sciences and Arts of Bosnia and Herzegovina.

Novel fluorogenic probe for fluoride ion based on the fluoride-induced cleavage of tert-butyldimethylsilyl ether

NASA Astrophysics Data System (ADS)

Yang, Xiao-Feng

2007-06-01

A highly sensitive and selective fluorogenic probe for fluoride ion, 4-methylumbelliferyl tert-butyldimethylsilyl ether (4-MUTBS), was designed and synthesized. 4-MUTBS was a weakly fluorescent compound and was synthesized via the one-step reaction of 4-MU with tert-butyldimethylsilyl chloride. Upon incubation with fluoride ion in acetone-water solution (7:3, v/v), the Si-O bond of 4-MUTBS was cleaved and highly fluorescent 4-methylumbelliferone (4-MU) was released, hence leading to the fluorescence increase of the reaction solution. The fluorescence increase is linearly with fluoride concentration in the range 50-8000 nmol l -1 with a detection limit of 19 nmol l -1 (3 σ). Because of the high affinity of silicon toward fluoride ion, the proposed probe shows excellent selectivity toward fluoride ion over other anions. The method has been successfully applied to the fluoride determination in toothpaste and tap water samples.

Fluoride bioavailability in saliva and plaque

PubMed Central

2012-01-01

Background Different fluoride formulations may have different effects on caries prevention. It was the aim of this clinical study to assess the fluoride content, provided by NaF compared to amine fluoride, in saliva and plaque. Methods Eight trained volunteers brushed their teeth in the morning for 3 minutes with either NaF or amine fluoride, and saliva and 3-day-plaque-regrowth was collected at 5 time intervals during 6 hours after tooth brushing. The amount of collected saliva and plaque was measured, and the fluoride content was analysed using a fluoride sensitive electrode. All subjects repeated all study cycles 5 times, and 3 cycles per subject underwent statistical analysis using the Wilcoxon-Mann-Whitney test. Results Immediately after brushing the fluoride concentration in saliva increased rapidly and dropped to the baseline level after 360 minutes. No difference was found between NaF and amine fluoride. All plaque fluoride levels were elevated after 30 minutes until 120 minutes after tooth brushing, and decreasing after 360 minutes to baseline. According to the highly individual profile of fluoride in saliva and plaque, both levels of bioavailability correlated for the first 30 minutes, and the fluoride content of saliva and plaque was back to baseline after 6 hours. Conclusions Fluoride levels in saliva and plaque are interindividually highly variable. However, no significant difference in bioavailability between NaF and amine fluoride, in saliva, or in plaque was found. PMID:22230722

Total and Free Fluoride Concentration in Various Brands of Toothpaste Marketed in India

PubMed Central

Siddanna, Sunitha

2015-01-01

Background For fluoridated toothpaste to be effective in controlling dental caries, an adequate concentration of soluble fluoride must be available in the oral cavity. Aim To determine the total and free fluoride concentration in various brands of toothpaste marketed in India. Materials and Methods Three samples of 12 different toothpastes were purchased from supermarkets in Mysore city, Karnataka, India. Toothpastes were analysed in duplicate using a fluoride ion-specific electrode. The concentration of total fluoride (TF) and total soluble fluoride (TSF) were determined. Results Measured TF was consistent with that declared by the manufacturer in five products. Four toothpastes showed lower TF and two higher TF than declared. Most toothpastes exhibited TSF concentrations similar to the TF content except four samples that displayed considerably lower TSF than TF. Conclusion The measurement of total and free fluoride concentrations of toothpastes available in India showed inhomogenities. Therefore there is a need for stringent regulatory control measures for the determination of fluoride content in toothpastes in developing country like India. PMID:26557607

Analytical Determination of Fluoride Ion Using Gran's Semi-Antilog Plot.

ERIC Educational Resources Information Center

Barnhard, Ralph J.

1983-01-01

A quantitative determination for fluoride ion using a commercially available fluoride electrode is described. The procedure referred to as known-addition is employed with the data processed on Gran's Plot Paper. Background information, experimental procedures, and advantages/disadvantages of the method are discussed. (JN)

Optical waveguides in fluoride lead silicate glasses fabricated by carbon ion implantation

NASA Astrophysics Data System (ADS)

Shen, Xiao-liang; Wang, Yue; Zhu, Qi-feng; Lü, Peng; Li, Wei-nan; Liu, Chun-xiao

2018-03-01

The carbon ion implantation with energy of 4.0 MeV and a dose of 4.0×1014 ions/cm2 is employed for fabricating the optical waveguide in fluoride lead silicate glasses. The optical modes as well as the effective refractive indices are measured by the prism coupling method. The refractive index distribution in the fluoride lead silicate glass waveguide is simulated by the reflectivity calculation method (RCM). The light intensity profile and the energy losses are calculated by the finite-difference beam propagation method (FD-BPM) and the program of stopping and range of ions in matter (SRIM), respectively. The propagation properties indicate that the C2+ ion-implanted fluoride lead silicate glass waveguide is a candidate for fabricating optical devices.

Fluoride exposure and its health risk assessment in drinking water and staple food in the population of Dayyer, Iran, in 2013

PubMed Central

Keshavarz, Somayye; Ebrahimi, Afshin; Nikaeen, Mahnaz

2015-01-01

Aims: The aims of this study were to determine fluoride concentration in drinking water and staple foods consumed by residents of Dayyer port (Bushehr province, south of Iran) and to assess its health risk via human intake in 2013. Materials and Methods: Health risk assessment due to fluoride exposure via consumption of drinking water, date, vegetables and fish was conducted in spring and summer of 2013 using the US-EPA (United States—Environmental Protection Agency) method, which considers hazard quotient (HQ) as a ratio of the estimated dose of a contaminant to the reference dose. A fluoride ion-selective electrode (ISE) measured the fluoride contents of food samples. The sodium-2-(parasulfophenyl largo)-1,8-dihydroxy-3,6-naphtnalene disulfonate colorimetric method (SPADNS) was used to determine fluoride concentration in water samples. Results: The total estimated oral intake of fluoride for children in summer and spring were 120.6 and 145.6 µg/kg/day, respectively. These values for adults were 99.2 and 112 µg/kg/day. This survey demonstrated that drinking water was the most important contributor of dietary fluoride intake in the study area. Conclusion: HQ values for adults and children were >1 which approves that a potential health risk of fluorosis can exist. The recommendations for the study area are supplying drinking water from alternative sources and defluoridation of drinking water by an adsorption technique and membrane filtration, respectively. Furthermore, people are suggested to have a good nutrition (especially rich of vitamin C) to reduce the risk of fluorosis. PMID:27462614

Fluorination of amorphous thin-film materials with xenon fluoride

DOEpatents

Weil, R.B.

1987-05-01

A method is disclosed for producing fluorine-containing amorphous semiconductor material, preferably comprising amorphous silicon. The method includes depositing amorphous thin-film material onto a substrate while introducing xenon fluoride during the film deposition process.

Fluorination of amorphous thin-film materials with xenon fluoride

DOEpatents

Weil, Raoul B.

1988-01-01

A method is disclosed for producing fluorine-containing amorphous semiconductor material, preferably comprising amorphous silicon. The method includes depositing amorphous thin-film material onto a substrate while introducing xenon fluoride during the film deposition process.

Fluoridation advocacy in Queensland: a long and winding road.

PubMed

Akers, Harry Francis; Foley, Michael Anthony

2012-10-01

By 1977, all Australian states and mainland territories, with the exception of Queensland, had widely implemented adjusted water fluoridation. This disparity in public health policy persisted until 2008. This study analyses the sociopolitical and socioeconomic backgrounds that underpinned the repeal of the Fluoridation of Public Water Supplies Act (1963) and its replacement with the Water Fluoridation Act (2008). The authors used a literature review and historic method. References are in the public domain. The devolution, without funding, of a discretionary local authority power to fluoridate contributed to the perennial low fluoridation status in Queensland. A window of opportunity for fluoridation advocates opened between 2003 and 2008. Now that 87% of Queenslanders have access to optimally fluoridated water, Queensland premier Anna Bligh has largely delivered on a promise made in 2007 to fluoridate water supplies across the state. The implementation of adjusted water fluoridation requires not only political stability and resolve, but also centralised authority. The last of these factors must embrace the decision, the funding and the indemnity. State control over water-related infrastructure and water treatment enhances prospects for fluoridation. The roles of opinion polls, internal advisers and departmental figures are also confirmed. Political repercussions were minimal. © 2012 FDI World Dental Federation.

Short term serum pharmacokinetics of diammine silver fluoride after oral application

PubMed Central

2012-01-01

Background There is growing interest in the use of diammine silver fluoride (DSF) as a topical agent to treat dentin hypersensitivity and dental caries as gauged by increasing published research from many parts of the world. While DSF has been available in various formulations for many years, most of its pharmacokinetic aspects within the therapeutic concentration range have never been fully characterized. Methods This preliminary study determined the applied doses (3 teeth treated), maximum serum concentrations, and time to maximum serum concentration for fluoride and silver in 6 adults over 4 h. Fluoride was determined using the indirect diffusion method with a fluoride selective electrode, and silver was determined using inductively coupled plasma-mass spectrometry. The mean amount of DSF solution applied to the 3 teeth was 7.57 mg (6.04 μL). Results Over the 4 hour observation period, the mean maximum serum concentrations were 1.86 μmol/L for fluoride and 206 nmol/L for silver. These maximums were reached 3.0 h and 2.5 h for fluoride and silver, respectively. Conclusions Fluoride exposure was below the U.S. Environmental Protection Agency (EPA) oral reference dose. Silver exposure exceeded the EPA oral reference dose for cumulative daily exposure over a lifetime, but for occasional use was well below concentrations associated with toxicity. This preliminary study suggests that serum concentrations of fluoride and silver after topical application of DSF should pose little toxicity risk when used in adults. Clinical trials registration NCT01664871. PMID:23272643

21 CFR 175.270 - Poly(vinyl fluoride) resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

...(vinyl fluoride) basic resins have an intrinsic viscosity of not less than 0.75 deciliter per gram as determined by ASTM method D1243-79, “Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride... (ASTM method D1243-79, “Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers...

Dentifrices, mouthwashes, and remineralization/caries arrestment strategies

PubMed Central

Zero, Domenick T

2006-01-01

While our knowledge of the dental caries process and its prevention has greatly advanced over the past fifty years, it is fair to state that the management of this disease at the level of the individual patient remains largely empirical. Recommendations for fluoride use by patients at different levels of caries risk are mainly based on the adage that more is better. There is a general understanding that the fluoride compound, concentration, frequency of use, duration of exposure, and method of delivery can influence fluoride efficacy. Two important factors are (1) the initial interaction of relatively high concentrations of fluoride with the tooth surface and plaque during application and (2) the retention of fluoride in oral fluids after application. Fluoride dentifrices remain the most widely used method of delivering topical fluoride. The efficacy of this approach in preventing dental caries is beyond dispute. However, the vast majority of currently marketed dentifrice products have not been clinically tested and have met only the minimal requirements of the FDA monograph using mainly laboratory testing and animal caries testing. Daily use of fluoride dental rinses as an adjunct to fluoride dentifrice has been shown to be clinically effective as has biweekly use of higher concentration fluoride rinses. The use of remineralizing agents (other than fluoride), directed at reversing or arresting non-cavitated lesions, remains a promising yet largely unproven strategy. High fluoride concentration compounds, e.g., AgF, Ag(NH3)2F, to arrest more advanced carious lesions with and without prior removal of carious tissue are being used in several countries as part of the Atraumatic Restorative Treatment (ART) approach. Most of the recent innovations in oral care products have been directed toward making cosmetic marketing claims. There continues to be a need for innovation and collaboration with other scientific disciplines to fully understand and prevent dental caries. PMID:16934126

Evaluation of Fluoride Retention Due to Most Commonly Consumed Estuarine Fishes Among Fish Consuming Population of Andhra Pradesh as a Contributing Factor to Dental Fluorosis: A Cross-Sectional Study

PubMed Central

Ganta, Shravani; Nagaraj, Anup; Pareek, Sonia; Sidiq, Mohsin; Singh, Kushpal; Vishnani, Preeti

2015-01-01

Background Fluoride in drinking water is known for both beneficial and detrimental effects on health. The principal sources of fluoride include water, some species of vegetation, certain edible marine animals, dust and industrial processes. The purpose of this study was to evaluate the fluoride retention of most commonly consumed estuarine fishes among fish consuming population of Andhra Pradesh. Materials and Methods A cross-sectional study was conducted to evaluate the amount of fluoride retention due to ten most commonly consumed estuarine fishes as a contributing factor to Fluorosis by SPADNS Spectrophotometric method. The presence and severity of dental fluorosis among fish consuming population was recorded using Community Fluorosis Index. Statistical analysis was done using MedCalc v12.2.1.0 software. Results For Sea water fishes, the fluoride levels in bone were maximum in Indian Sardine (4.22 ppm). Amongst the river water fishes, the fluoride levels in bone were maximum in Catla (1.51 ppm). Also, the mean total fluoride concentrations of all the river fishes in skin, muscle and bone were less (0.86 ppm) as compared to the sea water fishes (2.59 ppm). It was unveiled that sea fishes accumulate relatively large amounts of Fluoride as compared to the river water fishes. The mean Community Fluorosis Index was found to be 1.06 amongst a sampled fish consuming population. Evaluation by Community Index for Dental fluorosis (CFI) suggested that fluorosis is of medium public health importance. Conclusion It was analysed that bone tends to accumulate more amount of fluoride followed by muscle and skin which might be due to the increased permeability and chemical trapping of fluoride inside the tissues. The amount of fluoride present in the fishes is directly related to the severity of fluorosis amongst fish consuming population, suggesting fishes as a contributing factor to fluorosis depending upon the dietary consumption. PMID:26266208

The efficacy of two oral hygiene regimens in reducing oral malodour: a randomised clinical trial.

PubMed

Feres, Magda; Figueiredo, Luciene Cristina; Faveri, Marcelo; Guerra, Marcelo C; Mateo, Luis R; Stewart, Bernal; Williams, Malcolm; Panagakos, Foti

2015-12-01

This study compared the efficacy of two oral hygiene regimens in reducing oral malodour and the proportions of bacterial species involved in the production of volatile sulphur compounds. Seventy subjects who participated in a halitosis-induction phase and achieved an organoleptic score of ≥ 3.0 [time point 0 (T0)] randomised into two groups: brushing with regular fluoride toothpaste alone (control group) or brushing with regular fluoride toothpaste followed by rinsing with a 0.075% cetylpyridinium chloride (CPC) mouthwash (CPC group). Subjects followed their assigned oral hygiene regimen for 21 days. Then, they underwent an organoleptic examination and measurement of volatile sulphur compounds (VSCs) using a portable gas chromatograph, 12 hours after their last oral hygiene procedure (T1) and 4 hours after an on-site oral hygiene (T2). Microbiological samples (supragingival biofilm, tongue coating and saliva) were analysed using checkerboard DNA-DNA hybridisation. Both therapies statistically significantly improved the organoleptic scores (P < 0.05), but the VSC levels and/or concentrations were reduced only in the CPC group (P < 0.05). In subjects rinsing with CPC, oral malodour scores were reduced by 49% at the 4-hour assessment (T2) compared with those not rinsing (P < 0.05). Red-complex pathogens were reduced more effectively in the CPC group than in the control group. Brushing followed by rinsing with a 0.075% CPC mouthwash provided statistically significantly greater reductions in oral malodour, measured organoleptically and instrumentally, and in the proportions of red-complex species when compared with brushing alone. © 2015 FDI World Dental Federation.

Analgesic use of inhaled methoxyflurane: Evaluation of its potential nephrotoxicity.

PubMed

Dayan, A D

2016-01-01

Methoxyflurane is a volatile, halogenated analgesic, self-administered in a controlled low dose from the Penthrox(®) inhaler for short-term pain relief. It was formerly used in significantly higher doses to produce anaesthesia, when it caused a specific type of dose-related renal tubular damage. The pathogenesis of the renal damage and clinical use of methoxyflurane are discussed here with evidence that a low but effective analgesic dose is not associated with the risk of renal adverse effects. The maximum dose employed to produce analgesia is limited to methoxyflurane 6 mL/day and 15 mL/week, producing a minimum alveolar concentration (MAC) of 0.59 MAC-hours. Renal damage is due to the metabolism of methoxyflurane and release of fluoride ions. Exposure of humans to methoxyflurane ≤2.0 MAC-hours, resulting in serum fluoride ≤40 µmol/L, has not been associated with renal tubular toxicity. The safety margin of analgesic use of methoxyflurane in the Penthrox ((®)) inhaler is at least 2.7- to 8-fold, based on methoxyflurane MAC-hours or serum fluoride level, with clinical experience suggesting it is higher. It is concluded from clinical experience in emergency medicine, surgical procedures and various experimental and laboratory investigations that the analgesic use of methoxyflurane in subanaesthetic doses in the Penthrox inhaler does not carry a risk of nephrotoxicity. © The Author(s) 2015.

Surface chemistry associated with the cooling and subaerial weathering of recent basalt flows

USGS Publications Warehouse

White, A.F.; Hochella, M.F.

1992-01-01

The surface chemistry of fresh and weathered historical basalt flows was characterized using surface-sensitive X-ray photoelectron spectroscopy (XPS). Surfaces of unweathered 1987-1990 flows from the Kilauea Volcano, Hawaii, exhibited variable enrichment in Al, Mg, Ca, and F due to the formation of refractory fluoride compounds and pronounced depletion in Si and Fe from the volatilization of SiF4 and FeF3 during cooling. These reactions, as predicted from shifts in thermodynamic equilibrium with temperature, are induced by diffusion of HF from the flow interiors to the cooling surface. The lack of Si loss and solid fluoride formation for recent basalts from the Krafla Volcano, Iceland, suggest HF degassing at higher temperatures. Subsequent short-term subaerial weathering reactions are strongly influenced by the initial surface composition of the flow and therefore its cooling history. Successive samples collected from the 1987 Kilauea flow demonstrated that the fluoridated flow surfaces leached to a predominantly SiO2 composition by natural weathering within one year. These chemically depleted surfaces were also observed on Hawaiian basalt flows dating back to 1801 AD. Solubility and kinetic models, based on thermodynamic and kinetic data for crystalline AlF3, MgF2, and CaF2, support observed elemental depletion rates due to chemical weathering. Additional loss of alkalis from the Hawaiian basalt occurs from incongruent dissolution of the basalt glass substrate during weathering. ?? 1992.

Streptozotocin Aggravated Osteopathology and Insulin Induced Osteogenesis Through Co-treatment with Fluoride.

PubMed

Yang, Chen; Zhang, Mengmeng; Li, Yagang; Wang, Yan; Mao, Weixian; Gao, Yuan; Xu, Hui

2015-12-01

The role of insulin in the mechanism underlying the excessive fluoride that causes skeletal lesion was studied. The in vitro bone marrow stem cells (BMSC) collected from Kunming mice were exposed to varying concentrations of fluoride with or without insulin. The cell viability and early differentiation of BMSC co-treated with fluoride and insulin were measured by using cell counting kit-8 and Gomori modified calcium-cobalt method, respectively. We further investigated the in vivo effects of varying dose of fluoride on rats co-treated with streptozotocin (STZ). Wistar rats were divided into six groups which included normal control, 10 mg fluoride/kg day group, 20 mg fluoride/kg day group, STZ control, STZ+10 mg fluoride/kg day group, and STZ+20 mg fluoride/kg day group. The rats were administered with sodium fluoride (NaF) by gavage with water at doses 10 and 20 mg fluoride/kg day for 2 months. In a period of one month, half of rats in every group were treated with streptozotocin (STZ) once through intraperitoneal injection at 52 mg/kg body weight. The serum glucose, HbA1c, and insulin were determined. Bone mineral content and insulin release were assessed. The results showed insulin combined with fluoride stimulated BMSC cell viability in vitro. The bone mineral content reduced in rats treated with higher dose of fluoride and decreased immensely in rat co-treated with fluoride and STZ. Similarly, a combination treatment of a high dose of fluoride and STZ decreased insulin sensitivity and activity. To sum up, these data indicated fluoride influenced insulin release, activity, and sensitivity. Furthermore, the insulin state in vivo interfered in the osteogenesis in turn and implied there was a close relation between insulin and bone pathogenesis in the mechanism of fluoride toxicity.

FLUORIDE: A REVIEW OF USE AND EFFECTS ON HEALTH.

PubMed

Kanduti, Domen; Sterbenk, Petra; Artnik, Barbara

2016-04-01

Appropriate oral health care is fundamental for any individual's health. Dental caries is still one of the major public health problems. The most effective way of caries prevention is the use of fluoride. The aim of our research was to review the literature about fluoride toxicity and to inform physicians, dentists and public health specialists whether fluoride use is expedient and safe. Data we used in our review were systematically searched and collected from web pages and documents published from different international institutions. Fluoride occurs naturally in our environment but we consume it in small amounts. Exposure can occur through dietary intake, respiration and fluoride supplements. The most important factor for fluoride presence in alimentation is fluoridated water. Methods, which led to greater fluoride exposure and lowered caries prevalence, are considered to be one of the greatest accomplishments in the 20th century`s public dental health. During pregnancy, the placenta acts as a barrier. The fluoride, therefore, crosses the placenta in low concentrations. Fluoride can be transmitted through the plasma into the mother's milk; however, the concentration is low. The most important action of fluoride is topical, when it is present in the saliva in the appropriate concentration. The most important effect of fluoride on caries incidence is through its role in the process of remineralization and demineralization of tooth enamel. Acute toxicity can occur after ingesting one or more doses of fluoride over a short time period which then leads to poisoning. Today, poisoning is mainly due to unsupervised ingestion of products for dental and oral hygiene and over-fluoridated water. Even though fluoride can be toxic in extremely high concentrations, it`s topical use is safe. The European Academy of Paediatric Dentistry (EAPD) recommends a preventive topical use of fluoride supplements because of their cariostatic effect.

Influence of the method of fluoride administration on toxicity and fluoride concentrations in Japanese quail

USGS Publications Warehouse

Fleming, W.J.; Schuler, C.A.

1988-01-01

Young Japanese quail (Coturnix japonica) were administered NaF for 16 d either in their diet or by esophageal intubation. Based on the total fluoride ion (Emg F-) intake over the l6-d experimental period, fluoride administered by intubation was at least six times more toxic than that fed in the diet. Dietary concentrations of 1,000 ppm F- (Emg F- for 16 d = approx. 144) produced no mortality, whereas intubated doses produced 73% or greater mortality in all groups administered 54 mg F- /kg/d or more (Emg F- for 16 d _ approx. 23 mg). GraphIc companson of the regression of log F- ppm in femurs/mg F- intake showed that fluoride levels in the femurs of quail administered fluoride by intubation were higher than in those administered fluoride in the diet.

Fluorination utilizing thermodynamically unstable fluorides and fluoride salts thereof

DOEpatents

Bartlett, Neil; Whalen, J. Marc; Chacon, Lisa

2000-12-12

A method for fluorinating a carbon compound or cationic carbon compound utilizes a fluorination agent selected from thermodynamically unstable nickel fluorides and salts thereof in liquid anhydrous hydrogen fluoride. The desired carbon compound or cationic organic compound to undergo fluorination is selected and reacted with the fluorination agent by contacting the selected organic or cationic organic compound and the chosen fluorination agent in a reaction vessel for a desired reaction time period at room temperature or less.

[Dental fluorosis and dental caries prevalence in Senegalese children living in a high-fluoride area and consuming a poor fluoridated drinking water].

PubMed

Faye, M; Diawara, C K; Ndiaye, K R; Yam, A A

2008-01-01

The role of fluoride in dental caries prevention when applied at optimal levels is well established. However, ingestion of excessive fluoride during tooth development can cause structural changes in tooth enamel named fluorosis. At Gandiaye a city situated in the Senegalese endemic fluorosis area, the main water supply provided by a unique drilling with highly fluoridated water has broken down in 1996. Since then, the drinking water comes from wells which have poor levels of fluorides. The aims of this study were to evaluate the prevalence and severity of dental fluorosis and tooth decays in children born and reared continuously at Gandiaye after the stoppage of the drills and who were drinking water well. Water samples were collected from two wells and analyzed using a spectrometer and a specific fluoride electrode. The prevalence and severity of dental fluorosis was evaluated according to Dean's method, and the caries experience was measured using the DMF teeth index in 150 children aged from 6 to 8 years. The fluoride levels in the water well were comprised between 0.03 ppm and 0.09 ppm according to the method used. The prevalence of dental fluorosis was 39.33% with the predominance of the very low to low fluorosis forms. The tooth decay prevalence was 48.66% and the mean DMF tooth was 0.98. A significant relationship was found between the dental fluorosis and the low caries levels. A low to moderate dental fluorosis associated with a significant decrease of caries prevalence was found in children living in a high-fluoride area and consuming poorly fluorided water.

Prevalence of fluorosis and identification of fluoride endemic areas in Manur block of Tirunelveli District, Tamil Nadu, South India

NASA Astrophysics Data System (ADS)

Gopalakrishnan, Subarayan Bothi; Viswanathan, Gopalan; Siva Ilango, S.

2012-12-01

Prevalence of fluorosis is mainly due to the consumption of more fluoride through drinking water. It is necessary to identify the fluoride endemic areas to adopt remedial measures for the people under the risk of fluorosis. The objectives of this study were to identify the exact location of fluoride endemic areas in Manur block of Tirunelveli District and to estimate fluoride exposure level through drinking water for different age groups. Identification of fluoride endemic areas was performed through Isopleth and Google earth mapping techniques. Fluoride level in drinking water samples was estimated by fluoride ion selective electrode method. A systematic clinical survey conducted in 19 villages of Manur block revealed the rate of prevalence of fluorosis. From this study, it has been found that Alavanthankulam, Melapilliyarkulam, Keezhapilliyarkulam, Nadupilliyarkulam, Keezhathenkalam and Papankulam are the fluoride endemic villages, where the fluoride level in drinking water is above 1 mg/l. Consumption of maximum fluoride exposure levels of 0.30 mg/kg/day for infants, 0.27 mg/kg/day for children and 0.15 mg/kg/day for adults were found among the respective age group people residing in high fluoride endemic area. As compared with adequate intake level of fluoride of 0.01 mg/kg/day for infants and 0.05 mg/kg/day for other age groups, the health risk due to excess fluoride intake to the people of Alavanthankulam and nearby areas has become evident. Hence the people of these areas are advised to consume drinking water with optimal fluoride to avoid further fluorosis risks.

Prevalence of Brick Tea-Type Fluorosis in the Tibet Autonomous Region

PubMed Central

Fan, Zhipeng; Gao, Yanhui; Wang, Wei; Gong, Hongqiang; Guo, Min; Zhao, Shengcheng; Liu, Xuehui; Yu, Bing; Sun, Dianjun

2016-01-01

Background The prevalence of brick tea-type fluorosis is high in Tibet because of the habit of drinking brick tea in this region. Brick tea-type fluorosis has become an urgent public health problem in China. Methods A cross-sectional survey was conducted to investigate prevalence of brick tea-type fluorosis in all districts of Tibet using a stratified cluster sampling method. Dental fluorosis in children aged 8–12 years and clinical skeletal fluorosis in adults were diagnosed according to the national criteria. A total of 423 children and 1320 adults participated in the study. Samples of drinking water, brick tea, brick tea infusion (or buttered tea), and urine were collected and measured for fluoride concentrations by the fluoride ion selective electrode method. Results The fluoride level in all but one of the brick tea samples was above the national standard. The average daily fluoride intake from drinking brick tea in all seven districts in Tibet was much higher than the national standard. The prevalence of dental fluorosis was 33.57%, and the prevalence of clinical skeletal fluorosis was 46.06%. The average daily fluoride intake from drinking brick tea (r = 0.292, P < 0.05), urine fluoride concentrations in children (r = 0.134, P < 0.05), urine fluoride concentrations in adults (r = 0.162, P < 0.05), and altitude (r = 0.276, P < 0.05) were positively correlated with the prevalence of brick tea-type fluorosis. Herdsmen had the highest fluoride exposure and the most severe skeletal fluorosis. Conclusions Brick tea-type fluorosis in Tibet is more serious than in other parts of China. The altitude and occupational factors are important risk factors for brick tea-type fluorosis. PMID:26499132

Quantification of 18F-Fluoride Kinetics: Evaluation of Simplified Methods.

PubMed

Raijmakers, Pieter; Temmerman, Olivier P P; Saridin, Carrol P; Heyligers, Ide C; Becking, Alfred G; van Lingen, Arthur; Lammertsma, Adriaan A

2014-07-01

(18)F-fluoride PET is a promising noninvasive method for measuring bone metabolism and bone blood flow. The purpose of this study was to assess the performance of various clinically useful simplified methods by comparing them with full kinetic analysis. In addition, the validity of deriving bone blood flow from K1 of (18)F-fluoride was investigated using (15)O-H2O as a reference. Twenty-two adults (mean age ± SD, 44.8 ± 25.2 y), including 16 patients scheduled for bone surgery and 6 healthy volunteers, were studied. All patients underwent dynamic (15)O-H2O and (18)F-fluoride scans before surgery. Ten of these patients had serial PET measurements before and at 2 time points after local bone surgery. During all PET scans, arterial blood was monitored continuously. (18)F-fluoride data were analyzed using nonlinear regression (NLR) and several simplified methods (Patlak and standardized uptake value [SUV]). SUV was evaluated for different time intervals after injection and after normalizing to body weight, lean body mass, and body surface area, and simplified measurements were compared with NLR results. In addition, changes in SUV and Patlak-derived fluoride influx rate (Ki) after surgery were compared with corresponding changes in NLR-derived Ki. Finally, (18)F-fluoride K1 was compared with bone blood flow derived from (15)O-H2O data, using the standard single-tissue-compartment model. K1 of (18)F-fluoride correlated with measured blood flow, but the correlation coefficient was relatively low (r = 0.35, P < 0.001). NLR resulted in a mean Ki of 0.0160 ± 0.0122, whereas Patlak analysis, for the interval 10-60 min after injection, resulted in an almost-identical mean Ki of 0.0161 ± 0.0117. The Patlak-derived Ki, for 10-60 min after injection, showed a high correlation with the NLR-derived Ki (r = 0.976). The highest correlation between Ki and lean body mass-normalized SUV was found for the interval 50-60 min (r = 0.958). Finally, changes in SUV correlated significantly with those in Ki (r = 0.97). The present data support the use of both Patlak and SUV for assessing fluoride kinetics in humans. However, (18)F-fluoride PET has only limited accuracy in monitoring bone blood flow. © 2014 by the Society of Nuclear Medicine and Molecular Imaging, Inc.

Removal of fluoride from drinking water using aluminum hydroxide coated activated carbon prepared from bark of Morinda tinctoria

NASA Astrophysics Data System (ADS)

Amalraj, Augustine; Pius, Anitha

2017-10-01

The aim of this study is to design and develop a novel cost effective method for fluoride removal, applicable to rural areas of developing countries. Adsorption is widely considered as one of the appropriate technologies for water defluoridation. This study investigates the feasibility of using low-cost biomass based activated carbon from the bark of Morinda tinctoria coated with aluminum hydroxide (AHAC) for water defluoridation, at neutral pH range. Characterization of AHAC was done through IR, SEM with EDAX studies before and after fluoride treatment. The fluoride adsorption capacity of AHAC as a function of contact time, pH and initial fluoride concentration was investigated. The role of co-existing interfering ions also was studied. The isotherm and kinetic models were used to understand the nature of the fluoride adsorption onto AHAC. Freundlich isotherm and intra-particle diffusion were the best-fitting models for the adsorption of fluoride on AHAC. Fluoride adsorption kinetics well fitted with pseudo-second order model. The results showed excellent fluoride adsorption capacity was found to be 26.03 mg g-1 at neutral pH.

Concentration of Fluoride in Cow's and Buffalo's Milk in Relation to Varying Levels of Fluoride Concentration in Drinking Water of Mathura City in India- A Pilot Study.

PubMed

Gupta, Prahlad; Gupta, Nidhi; Meena, Komal; Moon, Ninad Joshirao; Kumar, Puneet; Kaur, Ravneet

2015-05-01

To estimate fluoride concentration in drinking water, cow's milk and buffalo's milk and to correlate the concentration of fluoride in cow's milk and buffalo's milk with varying levels of fluoride concentration in drinking water. Ten households having both cows and buffalo's were selected by convenience in each of the 3 zones (below optimum fluoride <0.7 ppm (parts per million), optimum fluoride 0.7-1.2 ppm and above optimum fluoride areas > 1.2 ppm). From these selected households, 200 ml of fresh milk of both cows and buffaloes was collected along with 200 ml of drinking water for estimation of fluoride concentration by using a fluoride ion selective electrode method. The data was analysed using SPSS, version 11.5 for windows. The mean fluoride concentration of drinking water, cow's milk and buffalo's milk in three different fluoride zones was 0.89±0.39, 0.09±0.07, 0.09±0.08 respectively. Pearson's correlation found a statistically significant correlation between fluoride concentrations in cow's and buffalo's milk with varying levels of fluoride concentration in drinking water in zone B and zone C. However, this correlation was not statistically significant in zone A. With an increase in fluoride concentration in drinking water there was an increase in concentration of fluoride in cow's and buffalo's milk. We conclude that this association is seen in conjunction to not only a single factor but rather due to culmination of several other aspects. So, there is a need to elucidate the other factors that might be contributing to this increase and dental fluorosis.

[Geographical distribution of fluoride in the public water supply in the province of Tucumán, Argentina].

PubMed

Durán, Raúl Alberto; Durán, Estela Liliana; Ojeda, Graciela de Jesús; Castellanos, Walter Alfredo

2017-01-01

This work studied the geographical distribution of fluoride content in the public water supply in the province of Tucumán, Argentina. A total of 1,210 samples were collected in 190 localities of the 17 departments of the province during the 2008-2012 period. The analytical determination was performed using the SPADNS method and QGis 2.16 was used for processing the information. The fluoride content requirements in the studied localities were determined according to the Argentine Food Code. The results showed that 94% of population studied consumed water with fluoride concentrations below the recommended limits, 5% were exposed to fluoride concentrations above the required maximum limit and 1% consumed water at optimal fluoride concentrations. The maps showed a heterogeneous geographical distribution of fluorides, in which areas with deficit, excess and recommended values of fluorides can be differentiated; in some departments an inverse relationship between the density of the hydrological network and fluoride concentration can be observed. In the capital of the province, the average value found was 0.32 mg/l, presenting a homogeneous geographical distribution. The information obtained is indispensable for the proper management of fluoride, so as to improve public health through policy.

FLUORIDE CONCENTRATIONS IN INDUSTRIALIZED BEVERAGES CONSUMED BY CHILDREN IN THE CITY OF BAURU, BRAZIL

PubMed Central

Lodi, Carolina Simonetti; Ramires, Irene; Pessan, Juliano Pelim; Neves, Lucimara Teixeira das; Buzalaf, Marília Afonso Rabelo

2007-01-01

The increasing consumption of juices, soft drinks and teas among children has increased significantly fluoride ingestion at the age range of risk for development of dental fluorosis. Objective: The purpose of this study was to evaluate fluoride concentrations in some brands of industrialized beverages consumed by children in the city of Bauru, SP, Brazil. Material and Methods: 98 brands of beverages were analyzed, divided into 3 lots, comprising 36, 32 and 30 brands, respectively, for the first, second and third lots. Fluoride concentrations were determined by HMDS-facilitated diffusion, using a fluoride ion-specific electrode (Orion 9409). Results: Fluoride concentrations ranged between 0.04 and 1.76 μg F/mL. It was observed a wide variation in fluoride concentrations among the different brands, as well as the different lots of the same brand. There was no information on fluoride concentrations on the labels of any product. Conclusions: Some of the products analyzed could contribute significantly to the total fluoride intake and, thus, be important risk factors for development of dental fluorosis, which indicates the need of controlling the production of these beverages with respect to fluoride concentration. PMID:19089131

Effects of combined oleic acid and fluoride at sub-MIC levels on EPS formation and viability of Streptococcus mutans UA159 biofilms.

PubMed

Cai, Jian-Na; Kim, Mi-A; Jung, Ji-Eun; Pandit, Santosh; Song, Kwang-Yeob; Jeon, Jae-Gyu

2015-01-01

Despite the widespread use of fluoride, dental caries, a biofilm-related disease, remains an important health problem. This study investigated whether oleic acid, a monounsaturated fatty acid, can enhance the effect of fluoride on extracellular polysaccharide (EPS) formation by Streptococcus mutans UA159 biofilms at sub-minimum inhibitory concentration levels, via microbiological and biochemical methods, confocal fluorescence microscopy, and real-time PCR. The combination of oleic acid with fluoride inhibited EPS formation more strongly than did fluoride or oleic acid alone. The superior inhibition of EPS formation was due to the combination of the inhibitory effects of oleic acid and fluoride against glucosyltransferases (GTFs) and GTF-related gene (gtfB, gtfC, and gtfD) expression, respectively. In addition, the combination of oleic acid with fluoride altered the bacterial biovolume of the biofilms without bactericidal activity. These results suggest that oleic acid may be useful for enhancing fluoride inhibition of EPS formation by S. mutans biofilms, without killing the bacterium.

Daily Fluoride Intake from Iranian Green Tea: Evaluation of Various Flavorings on Fluoride Release

PubMed Central

Maleki, Afshin; Daraei, Hiua; Mohammadi, Elham; Zandi, Shiva; Teymouri, Pari; Mahvi, Amir Hossien; Gharibi, Fardin

2016-01-01

With increased awareness of the health benefits of the compounds in green tea, especially polyphenols, its consumption is rising. The main purpose of this study is to determine the effect of different additives on the released fluoride into tea liquor and also daily fluoride intake. The concentrations of fluoride, nitrate, sulfate, and chloride were measured in 15 different flavored green teas (Refah-Lahijan). The fluoride and other anion concentrations were measured by ion chromatography method. The data were analyzed with Statistical Package for the Social Sciences version 16.0. The results showed that the minimum and maximum concentrations of fluoride in the green tea infusions were 0.162 mg/L (cinnamon-flavored green tea) and 3.29 mg/L (bagged peach-flavored green tea), respectively. The mean concentration of fluoride in the green tea leaves was 52 mg/kg, and approximately 89% of the fluoride was released from the green tea leaves into the infusions after brewing. The fluoride concentrations varied significantly among the examined green teas (P < 0.05). However, the additives had no significant effect on the fluoride release into the infusions (P > 0.05). Finally, drinking of the studied green teas cannot make a significant contribution to the daily dietary intake of F for consumers. PMID:27042093

Daily Fluoride Intake from Iranian Green Tea: Evaluation of Various Flavorings on Fluoride Release.

PubMed

Maleki, Afshin; Daraei, Hiua; Mohammadi, Elham; Zandi, Shiva; Teymouri, Pari; Mahvi, Amir Hossien; Gharibi, Fardin

2016-01-01

With increased awareness of the health benefits of the compounds in green tea, especially polyphenols, its consumption is rising. The main purpose of this study is to determine the effect of different additives on the released fluoride into tea liquor and also daily fluoride intake. The concentrations of fluoride, nitrate, sulfate, and chloride were measured in 15 different flavored green teas (Refah-Lahijan). The fluoride and other anion concentrations were measured by ion chromatography method. The data were analyzed with Statistical Package for the Social Sciences version 16.0. The results showed that the minimum and maximum concentrations of fluoride in the green tea infusions were 0.162 mg/L (cinnamon-flavored green tea) and 3.29 mg/L (bagged peach-flavored green tea), respectively. The mean concentration of fluoride in the green tea leaves was 52 mg/kg, and approximately 89% of the fluoride was released from the green tea leaves into the infusions after brewing. The fluoride concentrations varied significantly among the examined green teas (P < 0.05). However, the additives had no significant effect on the fluoride release into the infusions (P > 0.05). Finally, drinking of the studied green teas cannot make a significant contribution to the daily dietary intake of F for consumers.

18 F-Fluoride positron emission tomography/computed tomography for noninvasive in vivo quantification of pathophysiological bone metabolism in experimental murine arthritis

PubMed Central

2014-01-01

Introduction Evaluation of disease severity in experimental models of rheumatoid arthritis is inevitably associated with assessment of structural bone damage. A noninvasive imaging technology allowing objective quantification of pathophysiological alterations of bone structure in rodents could substantially extend the methods used to date in preclinical arthritis research for staging of autoimmune disease severity or efficacy of therapeutical intervention. Sodium 18 F-fluoride (18 F-NaF) is a bone-seeking tracer well-suited for molecular imaging. Therefore, we systematically examined the use of 18 F-NaF positron emission tomography/computed tomography (PET/CT) in mice with glucose-6-phosphate isomerase (G6PI)–induced arthritis for quantification of pathological bone metabolism. Methods F-fluoride was injected into mice before disease onset and at various time points of progressing experimental arthritis. Radioisotope accumulation in joints in the fore- and hindpaws was analyzed by PET measurements. For validation of bone metabolism quantified by 18 F-fluoride PET, bone surface parameters of high-resolution μCT measurements were used. Results Before clinical arthritis onset, no distinct accumulation of 18 F-fluoride was detectable in the fore- and hindlimbs of mice immunized with G6PI. In the course of experimental autoimmune disease, 18 F-fluoride bone uptake was increased at sites of enhanced bone metabolism caused by pathophysiological processes of autoimmune disease. Moreover, 18 F-fluoride signaling at different stages of G6PI-induced arthritis was significantly correlated with the degree of bone destruction. CT enabled identification of exact localization of 18 F-fluoride signaling in bone and soft tissue. Conclusions The results of this study suggest that small-animal PET/CT using 18 F-fluoride as a tracer is a feasible method for quantitative assessment of pathophysiological bone metabolism in experimental arthritis. Furthermore, the possibility to perform repeated noninvasive measurements in vivo allows longitudinal study of therapeutical intervention monitoring. PMID:25053370

METHOD OF PRODUCING URANIUM METAL BY ELECTROLYSIS

DOEpatents

Piper, R.D.

1962-09-01

A process is given for making uranium metal from oxidic material by electrolytic deposition on the cathode. The oxidic material admixed with two moles of carbon per one mole of uranium dioxide forms the anode, and the electrolyte is a mixture of from 40 to 75% of calcium fluoride or barium fluoride, 15 to 45% of uranium tetrafluoride, and from 10 to 20% of lithium fluoride or magnesium fluoride; the temperature of the electrolyte is between 1150 and 1175 deg C. (AEC)

Risk Assessment of Fluoride Intake from Tea in the Republic of Ireland and its Implications for Public Health and Water Fluoridation

PubMed Central

Waugh, Declan T.; Potter, William; Limeback, Hardy; Godfrey, Michael

2016-01-01

The Republic of Ireland (RoI) is the only European Country with a mandatory national legislation requiring artificial fluoridation of drinking water and has the highest per capita consumption of black tea in the world. Tea is a hyperaccumulator of fluoride and chronic fluoride intake is associated with multiple negative health outcomes. In this study, fifty four brands of the commercially available black tea bag products were purchased and the fluoride level in tea infusions tested by an ion-selective electrode method. The fluoride content in all brands tested ranged from 1.6 to 6.1 mg/L, with a mean value of 3.3 mg/L. According to our risk assessment it is evident that the general population in the RoI is at a high risk of chronic fluoride exposure and associated adverse health effects based on established reference values. We conclude that the culture of habitual tea drinking in the RoI indicates that the total cumulative dietary fluoride intake in the general population could readily exceed the levels known to cause chronic fluoride intoxication. Evidence suggests that excessive fluoride intake may be contributing to a wide range of adverse health effects. Therefore from a public health perspective, it would seem prudent and sensible that risk reduction measures be implemented to reduce the total body burden of fluoride in the population. PMID:26927146

Risk Assessment of Fluoride Intake from Tea in the Republic of Ireland and its Implications for Public Health and Water Fluoridation.

PubMed

Waugh, Declan T; Potter, William; Limeback, Hardy; Godfrey, Michael

2016-02-26

The Republic of Ireland (RoI) is the only European Country with a mandatory national legislation requiring artificial fluoridation of drinking water and has the highest per capita consumption of black tea in the world. Tea is a hyperaccumulator of fluoride and chronic fluoride intake is associated with multiple negative health outcomes. In this study, fifty four brands of the commercially available black tea bag products were purchased and the fluoride level in tea infusions tested by an ion-selective electrode method. The fluoride content in all brands tested ranged from 1.6 to 6.1 mg/L, with a mean value of 3.3 mg/L. According to our risk assessment it is evident that the general population in the RoI is at a high risk of chronic fluoride exposure and associated adverse health effects based on established reference values. We conclude that the culture of habitual tea drinking in the RoI indicates that the total cumulative dietary fluoride intake in the general population could readily exceed the levels known to cause chronic fluoride intoxication. Evidence suggests that excessive fluoride intake may be contributing to a wide range of adverse health effects. Therefore from a public health perspective, it would seem prudent and sensible that risk reduction measures be implemented to reduce the total body burden of fluoride in the population.

Site of Fluoride Accumulation in Navel Orange Leaves 1

PubMed Central

Chang, Chong W.; Thompson, C. Ray

1966-01-01

Fluoride-polluted navel orange leaves, Citrus sinensis (Linn.) Osbeck, were fractionated into the subcellular components in hexane/carbon tetrachloride mixtures having various densities. Fluoride was determined at each fraction. Analyses were also made for the subcellular distribution of chlorophyll, nitrogen, and DNA to assess the extent of cross-contamination of each component. The fraction containing cell wall, nuclei, and partly broken cells apparently contained a major amount of fluoride. However, if allowance was made for the cross-contamination of chloroplasts and chloroplast fragments, the fraction of chloroplasts was found to be the site of the highest fluoride accumulation. When each particulate component was washed with water after drying, the combined washings contained more than 50% of the total fluoride of the isolated fractions. The usual method of subcellular fractionation with aqueous solvent shifted the major site of fluoride accumulation from the fraction of chloroplasts to that of the supernatant. PMID:5908632

Prevalence of dental fluorosis in relation with different fluoride levels in drinking water among school going children in Sarada tehsil of Udaipur district, Rajasthan.

PubMed

Sarvaiya, B U; Bhayya, D; Arora, R; Mehta, D N

2012-01-01

To estimate the prevalence of dental fluorosis in relation with different fluoride levels in drinking water among school going children of 6-12 years age group. Dental fluorosis was recorded using Dean's index in school children of selected villages. The drinking water samples of all the selected villages were collected in polyethylene bottles and the fluoride content of these samples was determined by fluoride ion selective method using Orion microprocessor analyser. The overall prevalence of dental fluorosis was found to be 69.84%. An increase in the community fluorosis index (CFI) with corresponding increase in water fluoride content was found. There was an increase in prevalence of dental fluorosis with a corresponding increase in water fluoride content from 0.8 ppm to 4.1 ppm. A significantly strong positive correlation was found between CFI and fluoride concentration in drinking water.

Effect of home-used water purifier on fluoride concentration of drinking water in southern Iran

PubMed Central

Jaafari-Ashkavandi, Zohreh; Kheirmand, Mehdi

2013-01-01

Background: Fluoride in drinking water plays a key role in dental health. Due to the increasing use of water-purifier, the effect of these devices on fluoride concentration of drinking water was evaluated. Materials and Methods: Drinking water samples were collected before and after passing through a home water-purifier, from four different water sources. The fluoride, calcium and magnesium concentration of the samples were measured using the quantitative spectrophotometery technique. Data were analyzed by the Wilcoxon test. P value < 0.1 was considered as significant. Results: The result showed that the concentration of fluoride was 0.05-0.61 ppm before purification and was removed completely afterward. Furthermore, other ions reduced significantly after treatment by the water purifier. Conclusion: This study revealed that this device decreases the fluoride content of water, an issue which should be considered in low and high-fluoridated water sources. PMID:24130584

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campillo, M.; Valiente, M.; Lacharmoise, P. D.

Hydroxyapatite is the main mineral component of bones and teeth. Fluorapatite, a bioceramic that can be obtained from hydroxyapatite by chemical substitution of the hydroxide ions with fluoride, exhibits lower mineral solubility and larger mechanical strength. Despite the widespread use of fluoride against caries, a reliable technique for unambiguous assessment of fluoridation in in vitro tests is still lacking. Here we present a method to probe fluorapatite formation in fluoridated hydroxyapatite by combining Raman scattering with thermal annealing. In synthetic minerals, we found that effectively fluoride substituted hydroxyapatite transforms into fluorapatite only after heat treatment, due to the high activationmore » energy for this first order phase transition.« less

Knowledge, Attitude, and Barriers to Fluoride Application as a Preventive Measure among Oral Health Care Providers

PubMed Central

Al-Sumait, Noura; Al-Yahya, Hanan

2018-01-01

Objective To investigate the knowledge, attitude, and possible barriers to fluoride application among oral health-care providers in Kuwait. Methods A validated self-administered questionnaire was distributed to a random sample of 291 dentists. The questionnaire included four categories: dentists' characteristics, knowledge of and attitude towards fluoride application, factors influencing decision-making on prescription of fluoride, and the clinician's perception of own knowledge. Means, group differences, and logistic regression were calculated. Results 262 completed the questionnaire (response rate of 90%). Half of the participants (49%) reported that water fluoridation is the best method for caries prevention in children. Majority of the participants (80%) acknowledged that topical fluoride prevents dental caries, but only 40% frequently use it in their practices. Fear of overdose was a concern in 57% of the participants. About 31% believed that caries is a multifactorial disease and cannot be prevented. In addition, 32% of the dentists who thought caries is multifactorial and cannot be prevented stated that restorations take precedence over preventive therapy. Conclusion Despite the participants being in favor of topical fluoride application and believing in its effectiveness, certain barriers were apparent such as knowledge deficiencies, products labelling flaw, and lack of participation in effective continuing educational activities. PMID:29849638

Freeze concentration of proteins in Antarctic krill wash water

NASA Astrophysics Data System (ADS)

Qi, Xiangming; Xu, Jing; Zhao, Kuo; Guo, Hui; Ma, Lei

2017-12-01

Water-washing removes fluoride from Antarctic krill but produces large volumes of wash water containing water- soluble proteins and fluoride. The freeze concentration method was tested to determine if it could be used to recover water-soluble proteins while leaving the fluoride in solution. After freezing and thawing the wash water, protein and fluoride contents of the thawed fractions were determined to explore the melting regularity of components in the wash water. The highest concentration factors of protein and fluoride were obtained after 80 min of thawing, such as 1.48 ± 0.06 and 1.35 ± 0.04 times, respectively. The free amino-nitrogen (FAN) content and sodium dodecyl sulfate-polyacrylamide gel electrophoresis pattern results revealed that the highest concentrations of all ingredients were obtained after 80 min of the process. The degree of hydrolysis of all fractions from the thawing process fluctuated in a narrow range around 12% during the entire process, indicating that the thawing order did not change with various proteins or time during the entire thawing course. These results demonstrate that the freeze concentration method can be used to concentrate protein solutions, even those with fluoride. It was concluded that condensation was achieved and no ingredient could be separated, regardless of fluoride, amino acids, or different proteins in the water.

Fluoride exposure and indicators of thyroid functioning in the Canadian population: implications for community water fluoridation

PubMed Central

Barberio, Amanda M; Hosein, F Shaun; Quiñonez, Carlos; McLaren, Lindsay

2017-01-01

Background There are concerns that altered thyroid functioning could be the result of ingesting too much fluoride. Community water fluoridation (CWF) is an important source of fluoride exposure. Our objectives were to examine the association between fluoride exposure and (1) diagnosis of a thyroid condition and (2) indicators of thyroid functioning among a national population-based sample of Canadians. Methods We analysed data from Cycles 2 and 3 of the Canadian Health Measures Survey (CHMS). Logistic regression was used to assess associations between fluoride from urine and tap water samples and the diagnosis of a thyroid condition. Multinomial logistic regression was used to examine the relationship between fluoride exposure and thyroid-stimulating hormone (TSH) level (low/normal/high). Other available variables permitted additional exploratory analyses among the subset of participants for whom we could discern some fluoride exposure from drinking water and/or dental products. Results There was no evidence of a relationship between fluoride exposure (from urine and tap water) and the diagnosis of a thyroid condition. There was no statistically significant association between fluoride exposure and abnormal (low or high) TSH levels relative to normal TSH levels. Rerunning the models with the sample constrained to the subset of participants for whom we could discern some source(s) of fluoride exposure from drinking water and/or dental products revealed no significant associations. Conclusion These analyses suggest that, at the population level, fluoride exposure is not associated with impaired thyroid functioning in a time and place where multiple sources of fluoride exposure, including CWF, exist. PMID:28839078

Method of making porous ceramic fluoride

DOEpatents

Reiner, Robert H.; Holcombe, Cressie E.

1990-01-01

A process for making a porous ceramic composite where fumed silica particles are coated with a nitrate, preferably aluminum nitrate. Next the nitrate is converted to an oxide and formed into a desired configuration. This configuration is heated to convert the oxide to an oxide silicate which is then react with HF, resulting in the fluoride ceramic, preferably aluminum fluoride.

The Fluoride Content of Yerba Mate Depending on the Country of Origin and the Conditions of the Infusion.

PubMed

Łukomska, A; Jakubczyk, K; Maciejewska, D; Baranowska-Bosiacka, I; Janda, K; Goschorska, M; Chlubek, D; Bosiacka, B; Gutowska, I

2015-10-01

There are many reports of the positive effect of yerba mate on the human body. Elemental composition analysis of yerba mate revealed the presence of many microelements and macroelements, but there is no literature data referencing the content and the effect of the method of preparing the yerba mate infusion on the amount of released fluoride and thus the amount of this element supplied to the human body. Therefore, in the traditional way (cold and hot), we prepared infusions of yerba mate from different countries and determined in samples content of fluoride using potentiometric method. Hot infusions resulted in statistically significant (p = 0.03) increases in the amount of fluoride released from the dried material to the water, compared to brewing with water at room temperature. The successive refills of hot water also resulted in a release of the same amount of fluoride, although smaller than the infusion with water at room temperature (at the third refill, it was statistically significantly smaller at p = 0.003). With an increase in the number of hot water refills, the amount of fluoride released from the sample portion significantly decreased. Similar results were recorded when analyzing samples depending on the country of origin. The amount of fluoride released into the water differed statistically significantly depending on the country of origin. The most fluoride was determined in the infusions of yerba mate from Argentina and the least in infusions from Paraguay.

Enhanced fluoride adsorption by nano crystalline γ-alumina: adsorption kinetics, isotherm modeling and thermodynamic studies

NASA Astrophysics Data System (ADS)

Chinnakoti, Prathibha; Chunduri, Avinash L. A.; Vankayala, Ranganayakulu K.; Patnaik, Sandeep; Kamisetti, Venkataramaniah

2017-09-01

Nano materials in particular nano oxides with enhanced surface area and an excellent catalytic surface serve as potential adsorbents for defluoridation of water. In the present study nano γ-alumina was synthesized through a simple and low cost, surfactant assisted solution combustion method. As synthesized material was characterized by XRD and FESEM for its phase, size and morphological characteristics. Surface properties have been investigated by BET method. Nano γ-alumina was further used for a detailed adsorption study to remove fluoride from water. Batches of experiments were performed at various experimental conditions such as solution pH, adsorbent dose, initial fluoride concentration and contact time to test the defluoridation ability of γ-alumina. Fluoride Adsorption by nano sized γ-alumina was rapid and reached equilibrium within two hours. The adsorption worked well at pH 4.0, where ˜96 % of fluoride was found to be adsorbed on adsorbent. It was possible to reduce fluoride levels to as low as 0.3 mg/L (within the safe limit of WHO: ≤1.5 mg/L) from an initial fluoride levels of 10 mg/L. This could be achieved using a very small quantity, 1 g/L of γ-alumina at pH 4 within 1 h of contact time. Defluoridation capacity of nano γ-alumina was further investigated by fitting the equilibrium data to various isotherm as well as kinetic models. The present study revealed that γ-alumina could be an efficient adsorbent for treating fluoride contaminated water.

Association between water fluoride and the level of children's intelligence: a dose-response meta-analysis.

PubMed

Duan, Q; Jiao, J; Chen, X; Wang, X

2018-01-01

Higher fluoride concentrations in water have inconsistently been associated with the levels of intelligence in children. The following study summarizes the available evidence regarding the strength of association between fluoridated water and children's intelligence. Meta-analysis. PubMed, Embase, and Cochrane Library databases were systematically analyzed from November 2016. Observational studies that have reported on intelligence levels in relation to high and low water fluoride contents, with 95% confidence intervals (CIs) were included. Further, the results were pooled using inverse variance methods. The correlation between water fluoride concentration and intelligence level was assessed by a dose-response meta-analysis. Twenty-six studies reporting data on 7258 children were included. The summary results indicated that high water fluoride exposure was associated with lower intelligence levels (standardized mean difference : -0.52; 95% CI: -0.62 to -0.42; P < 0.001). The findings from subgroup analyses were consistent with those from overall analysis. The dose-response meta-analysis suggested a significant association between water fluoride dosage and intelligence (P < 0.001), while increased water fluoride exposure was associated with reduced intelligence levels. Greater exposure to high levels of fluoride in water was significantly associated with reduced levels of intelligence in children. Therefore, water quality and exposure to fluoride in water should be controlled in areas with high fluoride levels in water. Copyright © 2017. Published by Elsevier Ltd.

Association between urine fluoride and dental fluorosis as a toxicity factor in a rural community in the state of San Luis Potosi.

PubMed

Jarquín-Yañez, Lizet; de Jesús Mejía-Saavedra, José; Molina-Frechero, Nelly; Gaona, Enrique; Rocha-Amador, Diana Olivia; López-Guzmán, Olga Dania; Bologna-Molina, Ronell

2015-01-01

The aim of this study is to investigate urine fluoride concentration as a toxicity factor in a rural community in the state of San Luis Potosi, Mexico. A sample of 111 children exposed to high concentrations of fluoride in drinking water (4.13 mg/L) was evaluated. Fluoride exposure was determined by measuring urine fluoride concentration using the potentiometric method with an ion selective electrode. The diagnosis of dental fluorosis was performed by clinical examination, and the severity of damage was determined using Dean's index and the Thylstrup-Fejerskov (TF) index. The range of exposure in the study population, evaluated through the fluoride content in urine, was 1.1 to 5.9 mg/L, with a mean of 3.14±1.09 mg/L. Dental fluorosis was present in all subjects, of which 95% had severe cases. Higher urine fluoride levels and greater degrees of severity occurred in older children. The results show that dental fluorosis was determined by the presence of fluoride exposure finding a high positive correlation between the severity of fluorosis and urine fluoride concentration and the years of exposure suggested a cumulative effect.

Cross-Linked Poly(vinylidene fluoride-co-hexafluoropropene) (PVDF-co-HFP) Gel Polymer Electrolyte for Flexible Li-Ion Battery Integrated with Organic Light Emitting Diode (OLED)

PubMed Central

Kim, Ilhwan; Kim, Bong Sung; Nam, Seunghoon; Lee, Hoo-Jeong; Chung, Ho Kyoon; Cho, Sung Min; Luu, Thi Hoai Thuong; Hyun, Seungmin; Kang, Chiwon

2018-01-01

Here, we fabricate poly(vinylidene fluoride-co-hexafluoropropene) (PVDF-co-HFP) by electrospinning for a gel polymer electrolyte (GPE) for use in flexible Li-ion batteries (LIBs). As a solvent, we use N-methyl-2-pyrrolidone (NMP), which helps produce the cross-linked morphology of PVDF-co-HFP separator, owing to its low volatility. The cross-linked PVDF-co-HFP separator shows an uptake rate higher than that of a commercialized polypropylene (PP) separator. Moreover, the PVDF-co-HFP separator shows an ionic conductivity of 2.3 × 10−3 S/cm at room temperature, comparable with previously reported values. An LIB full-cell assembled with the PVDF-co-HFP-based GPE shows capacities higher than its counterpart with the commercialized PP separator, confirming that the cross-linked PVDF-co-HFP separator provides highly efficient ionic conducting pathways. In addition, we integrate a flexible LIB cell using the PVDF-co-HFP GPE with a flexible organic light emitting diode (OLED), demonstrating a fully flexible unit of LIB and OLED. PMID:29614800

Cross-Linked Poly(vinylidene fluoride-co-hexafluoropropene) (PVDF-co-HFP) Gel Polymer Electrolyte for Flexible Li-Ion Battery Integrated with Organic Light Emitting Diode (OLED).

PubMed

Kim, Ilhwan; Kim, Bong Sung; Nam, Seunghoon; Lee, Hoo-Jeong; Chung, Ho Kyoon; Cho, Sung Min; Luu, Thi Hoai Thuong; Hyun, Seungmin; Kang, Chiwon

2018-04-02

Here, we fabricate poly(vinylidene fluoride- co -hexafluoropropene) (PVDF- co -HFP) by electrospinning for a gel polymer electrolyte (GPE) for use in flexible Li-ion batteries (LIBs). As a solvent, we use N -methyl-2-pyrrolidone (NMP), which helps produce the cross-linked morphology of PVDF- co -HFP separator, owing to its low volatility. The cross-linked PVDF- co -HFP separator shows an uptake rate higher than that of a commercialized polypropylene (PP) separator. Moreover, the PVDF- co -HFP separator shows an ionic conductivity of 2.3 × 10 -3 S/cm at room temperature, comparable with previously reported values. An LIB full-cell assembled with the PVDF- co -HFP-based GPE shows capacities higher than its counterpart with the commercialized PP separator, confirming that the cross-linked PVDF- co -HFP separator provides highly efficient ionic conducting pathways. In addition, we integrate a flexible LIB cell using the PVDF- co -HFP GPE with a flexible organic light emitting diode (OLED), demonstrating a fully flexible unit of LIB and OLED.

Fluoride glass: Crystallization, surface tension

NASA Technical Reports Server (NTRS)

Doremus, R. H.

1988-01-01

Fluoride glass was levitated acoustically in the ACES apparatus on STS-11, and the recovered sample had a different microstructure from samples cooled in a container. Further experiments on levitated samples of fluoride glass are proposed. These include nucleation, crystallization, melting observations, measurement of surface tension of molten glass, and observation of bubbles in the glass. Ground experiments are required on sample preparation, outgassing, and surface reactions. The results should help in the development and evaluation of containerless processing, especially of glass, in the development of a contaminent-free method of measuring surface tensions of melts, in extending knowledge of gas and bubble behavior in fluoride glasses, and in increasing insight into the processing and properties of fluoride glasses.

Methods for globally treating silica optics to reduce optical damage

DOEpatents

Miller, Philip Edward; Suratwala, Tayyab Ishaq; Bude, Jeffrey Devin; Shen, Nan; Steele, William Augustus; Laurence, Ted Alfred; Feit, Michael Dennis; Wong, Lana Louie

2012-11-20

A method for preventing damage caused by high intensity light sources to optical components includes annealing the optical component for a predetermined period. Another method includes etching the optical component in an etchant including fluoride and bi-fluoride ions. The method also includes ultrasonically agitating the etching solution during the process followed by rinsing of the optical component in a rinse bath.

Method of preparing pure fluorine gas

DOEpatents

Asprey, Larned B.

1976-01-01

A simple, inexpensive system for purifying and storing pure fluorine is described. The method utilizes alkali metal-nickel fluorides to absorb tank fluorine by forming nickel complex salts and leaving the gaseous impurities which are pumped away. The complex nickel fluoride is then heated to evolve back pure gaseous fluorine.

Phosphate reduction in a hydroxyapatite fluoride removal system

NASA Astrophysics Data System (ADS)

Egner, A.

2012-12-01

Fluorosis is a widespread disease that occurs as a result of excess fluoride consumption and can cause severe tooth and bone deformations. To combat fluorosis, several previous studies have examined the potential to replace traditional bone char filters with synthetic hydroxyapatite. Calcite particles with a synthetic hydroxyapatite coating have been shown to effectively removed fluoride, yet the low-cost method for forming these particles leaves high amounts of phosphate both in synthesis waste-water and in filter effluent. High phosphate in filter effluent is problematic because consumption of extremely high phosphate can leach calcium from bones, further exacerbating the fluoride effect. This study examines ways of reducing and reusing waste. In particular, a method of fluoride removal is explored in which fluorapatite coatings may be formed directly. In preliminary studies, batches of 4.1g of Florida limestone (<710 μm) were equilibrated with 100 mL of 10ppm fluoride. In a control batch containing lime but no added phosphate, 14% treatment was achieved, but with added phosphate, 100% treatment was achieved in all batches. Batches with lower levels of phosphate took longer to reach 100% treatment, ranging from less than 24 hours in the highest phosphate batches to approximately 42 hours in the lowest batches. The lower levels tested were well within reasonable levels for drinking water and reached 0ppm fluoride in 42 hours or less.

γ-Aminobutyric acid ameliorates fluoride-induced hypothyroidism in male Kunming mice.

PubMed

Yang, Haoyue; Xing, Ronge; Liu, Song; Yu, Huahua; Li, Pengcheng

2016-02-01

This study evaluated the protective effects of γ-aminobutyric acid (GABA), a non-protein amino acid and anti-oxidant, against fluoride-induced hypothyroidism in mice. Light microscope sample preparation technique and TEM sample preparation technique were used to assay thyroid microstructure and ultrastructure; enzyme immunoassay method was used to assay hormone and protein levels; immunohistochemical staining method was used to assay apoptosis of thyroid follicular epithelium cells. Subacute injection of sodium fluoride (NaF) decreased blood T4, T3 and thyroid hormone-binding globulin (TBG) levels to 33.98 μg/l, 3 2.8 ng/ml and 11.67 ng/ml, respectively. In addition, fluoride intoxication induced structural abnormalities in thyroid follicles. Our results showed that treatment of fluoride-exposed mice with GABA appreciably decreased metabolic toxicity induced by fluoride and restored the microstructural and ultrastructural organisation of the thyroid gland towards normalcy. Compared with the negative control group, GABA treatment groups showed significantly upregulated T4, T3 and TBG levels (42.34 μg/l, 6.54 ng/ml and 18.78 ng/ml, respectively; P<0.05), properly increased TSH level and apoptosis inhibition in thyroid follicular epithelial cells. To the best of our knowledge, this is the first study to establish the therapeutic efficacy of GABA as a natural antioxidant in inducing thyroprotection against fluoride-induced toxicity. Copyright © 2015 Elsevier Inc. All rights reserved.

Effects of fluoride residue on thermal stability in Cu/porous low-k interconnects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kobayashi, Y.; Ozaki, S.; Nakamura, T.

2014-06-19

We have investigated the effects of fluoride residue on the thermal stability of a Cu/barrier metal (BM)/porous low-k film (k < 2.3) structure. We confirmed that the Cu agglomerated more on a BM/inter layer dielectric (ILD) with a fluoride residue. To consider the effect of fluoride residue on Cu agglomeration, the structural state at the Cu/BM interface was evaluated with a cross-section transmission electron microscope (TEM) and atomic force microscope (AFM). In addition, the chemical bonding state at the Cu/BM interface was evaluated with the interface peeling-off method and X-ray photoelectron spectroscopy (XPS). Moreover, we confirmed the ionization of fluoridemore » residue and oxidation of Cu with fluoride and moisture to clarify the effect of fluoride residue on Cu. Our experimental results indicated that the thermal stability in Cu/porous low-k interconnects was degraded by enhancement of Cu oxidation with fluoride ions diffusion as an oxidizing catalyst.« less

Risk assessment of fluoride exposure in drinking water of Tunisia.

PubMed

Guissouma, Wiem; Hakami, Othman; Al-Rajab, Abdul Jabbar; Tarhouni, Jamila

2017-06-01

The presence of fluoride in drinking water is known to reduce dental cavities among consumers, but an excessive intake of this anion might leads to dental and skeletal fluorosis. This study reports a complete survey of the fluoridated tap water taken from 100 water consumption points in Tunisia. The fluoride concentrations in tap water were between 0 and 2.4 mg L -1 . Risk assessment of Fluoride exposure was assessed depending on the age of consumers using a four-step method: hazard identification, toxicity reference values selection (TRVs), daily exposure assessment, and risk characterization. Our findings suggest that approximately 75% of the Tunisian population is at risk for dental decay, 25% have a potential dental fluorosis risk, and 20% might have a skeletal fluorosis risk according to the limits of fluoride in drinking water recommended by WHO. More investigations are recommended to assess the exposure risk of fluoride in other sources of drinking water such as bottled water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fluoride exposure and its health risk assessment in drinking water and staple food in the population of Dayyer, Iran, in 2013.

PubMed

Keshavarz, Somayye; Ebrahimi, Afshin; Nikaeen, Mahnaz

2015-01-01

The aims of this study were to determine fluoride concentration in drinking water and staple foods consumed by residents of Dayyer port (Bushehr province, south of Iran) and to assess its health risk via human intake in 2013. Health risk assessment due to fluoride exposure via consumption of drinking water, date, vegetables and fish was conducted in spring and summer of 2013 using the US-EPA (United States-Environmental Protection Agency) method, which considers hazard quotient (HQ) as a ratio of the estimated dose of a contaminant to the reference dose. A fluoride ion-selective electrode (ISE) measured the fluoride contents of food samples. The sodium-2-(parasulfophenyl largo)-1,8-dihydroxy-3,6-naphtnalene disulfonate colorimetric method (SPADNS) was used to determine fluoride concentration in water samples. The total estimated oral intake of fluoride for children in summer and spring were 120.6 and 145.6 µg/kg/day, respectively. These values for adults were 99.2 and 112 µg/kg/day. This survey demonstrated that drinking water was the most important contributor of dietary fluoride intake in the study area. HQ values for adults and children were >1 which approves that a potential health risk of fluorosis can exist. The recommendations for the study area are supplying drinking water from alternative sources and defluoridation of drinking water by an adsorption technique and membrane filtration, respectively. Furthermore, people are suggested to have a good nutrition (especially rich of vitamin C) to reduce the risk of fluorosis.

Training High School Students in the Scientific Method via Hands On Projects in a Laboratory Environment

DTIC Science & Technology

2015-02-27

Poly(vinylidene Fluoride with Trifluoroethylene) P(VDF-TrFE) 75:25 Thin Films by Atomic Force Microscope Nanolithography, Scanning, (04 2012): 0...doi: 10.1002/sca.21024 William Serrano, Nicholas J. Pinto. Electrospun Fibers of Poly(Vinylidene Fluoride -Trifluoroethylene)/Poly (3-Hexylthiophene...Nicholas Pinto. Electrospun fibers of poly (vinylidene fluoride -trifluoroethylene)/ poly (3- hexylthiophene) blends from tetrahydrofuran, National

Properties of multilayer filters

NASA Technical Reports Server (NTRS)

Baumeister, P. W.

1973-01-01

New methods were investigated of using optical interference coatings to produce bandpass filters for the spectral region 110 nm to 200 nm. The types of filter are: triple cavity metal dielectric filters; all dielectric reflection filters; and all dielectric Fabry Perot type filters. The latter two types use thorium fluoride and either cryolite films or magnesium fluoride films in the stacks. The optical properties of the thorium fluoride were also measured.

Caries prevention through the fluoridation of milk. A review.

PubMed

Bánóczy, Jolán; Rugg-Gunn, Andrew J

2007-10-01

The aim of this review is to give an overview of 50 years experience of milk fluoridation and draw conclusions about the applicability of the method. Fluoridated milk was first investigated in the early 1950s, almost simultaneously in Switzerland, the USA and Japan. Stimulated by the favourable results obtained from these early studies, the establishment of The Borrow Dental Milk Foundation (subsequently The Borrow Foundation) in England gave an excellent opportunity for further research, both clinical and non-clinical, and a productive collaboration with the World Health Organization from the early 1980s onwards. Numerous peer-reviewed publications in international journals showed clearly the bioavailability of fluoride in milk, and increased concentrations of fluoride in saliva, dental plaque, dental enamel and dentine, and urine, after consumption of fluoridated milk. Clinical trials were initiated in the 1980s--some of these can be classed as randomised controlled trials, while most of the clinical studies were community preventive programs. These evaluations showed clearly that the optimal daily intake of fluoride in milk is effective in preventing dental caries. At present, milk fluoridation programs are running continuously in about ten countries of the world. Fluoridation of milk can be recommended as a caries preventive measure where the fluoride concentration in drinking water is suboptimal, caries experience in children is significant, and there is an existing school milk program. The program should aim to provide fluoridated milk for at least 200 days per year and should commence before the children are 4 years of age.

Utility of check dams in dilution of fluoride concentration in ground water and the resultant analysis of blood serum and urine of villagers, Anantapur District, Andhra Pradesh, India.

PubMed

Bhagavan, S V B K; Raghu, V

2005-02-01

High levels of fluoride (beyond 1.5 ppm) in ground water as source of drinking water are common in many parts of Andhra Pradesh, India, causing fluorosis. The study carried out in endemic Nalgonda District, Andhra Pradesh, has indicated that the fluoride-rich ground water present in the wells located down stream and close to the surface water bodies is getting diluted by the low-fluoride surface water. Encouraged by this result, check dams were constructed upstream of the identified marginally high fluoride bearing ground water zones in Anantapur District to reduce fluoride levels as an alternate solution for safe drinking water. In this paper, an attempt is made to study the utility and effect of these check dams in dilution of fluoride concentration in drinking water and its resultant impact on the health aspects of certain villagers of Anantapur District through the analysis of their blood serum and urine. Ground water samples from three fluoride-affected villages, blood and urine of males and females from the same villages were collected and analyzed for fluoride using ion selective electrode method. The results indicated that the fluoride levels in blood serum and urine of males in the age group of 5-11 years are found to be the highest. The concentration of fluoride in ground water is directly proportional to the concentration of fluoride in blood serum and urine. The concentration of fluoride in ground water with depth of the aquifer is a function of lithology, amount and duration of rainfall, rate of infiltration, level of ground water exploitation in the area etc. The construction of check dams upstream of the identified marginally high fluoride waters will not only cause additional recharge of ground water but also reduces the fluoride concentration eventually improving the health of the villagers.

Absence of Fluoride Varnish–Related Adverse Events in Caries Prevention Trials in Young Children, United States

PubMed Central

Gregorich, Steven E.; Ramos-Gomez, Francisco; Braun, Patricia A.; Wilson, Anne; Albino, Judith; Tiwari, Tamanna; Harper, Maya; Batliner, Terrence S.; Rasmussen, Margaret; Cheng, Nancy F.; Santo, William; Geltman, Paul L.; Henshaw, Michelle; Gansky, Stuart A.

2017-01-01

Introduction Fluoride varnish is an effective prevention intervention for caries in young children. Its routine use in clinical care is supported by meta-analyses and recommended by clinical guidelines, including the US Preventive Services Task Force (B rating). This report is the first prospective systematic assessment of adverse events related to fluoride varnish treatment in young children. Methods We determined the incidence of adverse events related to fluoride varnish treatment in 3 clinical trials on the prevention of early childhood caries, conducted under the auspices of the Early Childhood Caries Collaborating Centers, an initiative sponsored by the National Institute of Dental and Craniofacial Research. Each trial incorporated use of fluoride varnish in its protocol and systematically queried all children’s parents or legal guardians about the occurrence of acute adverse events after each fluoride varnish treatment. Results A total of 2,424 community-dwelling, dentate children aged 0 to 5 years were enrolled and followed for up to 3 years. These children received a cumulative total of 10,249 fluoride varnish treatments. On average, each child received 4.2 fluoride varnish treatments. We found zero fluoride varnish–related adverse events. Conclusion Fluoride varnish was not associated with treatment-related adverse events in young children. Our findings support its safety as an effective prevention intervention for caries in young children. PMID:28207379

SBIR-Long fluoride fiber

NASA Astrophysics Data System (ADS)

Jaeger, Raymond E.; Vacha, Lubos J.

1987-08-01

This report summarizes results obtained under a program aimed at developing new techniques for fabricating long lengths of heavy metal fluoride glass (HMFG) optical fiber. A new method for overcladding conventional HMFG preforms with a low melting oxide glass was developed, and improvements in the rotational casting method were made to increase preform length. The resulting composite glass canes consist of a fluoride glass overcoat layer to enhance strength and chemical durability. To show feasibility, prototype optical fiber preforms up to 1.6 cm in diameter with lengths of 22 cm were fabricated. These were drawn into optical fibers with lengths up to 900 meters.

Use of Nitrogen Trifluoride To Purify Molten Salt Reactor Coolant and Heat Transfer Fluoride Salts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheele, Randall D.; Casella, Andrew M.; McNamara, Bruce K.

2017-05-02

Abstract: The molten salt cooled nuclear reactor is included as one of the Generation IV reactor types. One of the challenges with the implementation of this reactor is purifying and maintaining the purity of the various molten fluoride salts that will be used as coolants. The method used for Oak Ridge National Laboratory’s molten salt experimental test reactor was to treat the coolant with a mixture of H2 and HF at 600°C. In this article we evaluate thermal NF3 treatment for purifying molten fluoride salt coolant candidates based on NF3’s 1) past use to purify fluoride salts, 2) other industrialmore » uses, 3) commercial availability, 4) operational, chemical, and health hazards, 5) environmental effects and environmental risk management methods, 6) corrosive properties, and 7) thermodynamic potential to eliminate impurities that could arise due to exposure to water and oxygen. Our evaluation indicates that nitrogen trifluoride is a viable and safer alternative to the previous method.« less

Effects of combined exogenous dextranase and sodium fluoride on Streptococcus mutans 25175 monospecies biofilms.

PubMed

Yang, Ying-Ming; Jiang, Dan; Qiu, Yuan-Xin; Fan, Rong; Zhang, Ru; Ning, Mei-Zhi; Shao, Mei-Ying; Zhang, Chao-Liang; Hong, Xiao; Hu, Tao

2013-10-01

To investigate the effects of exogenous dextranase and sodium fluoride on a S. mutans monospecies biofilm. S. mutans 25175 was grown in tryptone soya broth medium, and biofilm was formed on glass slides with 1.0% sucrose. Exogenous dextranase and sodium fluoride were added alone or together. The biofilm morphology was analyzed by confocal laser scanning microscopy. The effects of the drug on the adhesion and exopolysaccharide production by the biofilms were evaluated by scintillation counting and the anthrone method, respectively. In this study, we found that the structure of initial biofilm and mature biofilm were partly altered by dextranase and high concentrations of sodium fluoride separately. However, dextranase combined with a low concentration of sodium fluoride could clearly destroy the typical tree-like structure of the biofilm, and led to less bacterial adhesion than when the dextranase or fluoride were used alone (P < 0.05). The amounts of soluble and insoluble exopolysaccharide were significantly reduced by combining dextranase with a low concentration of sodium fluoride, much more than when they were used alone (P < 0.05). These data indicate that dextranase and a low concentration of sodium fluoride may have synergistic effects against S. mutans biofilm and suggest the application of a low concentration of sodium fluoride in anticaries treatment.

Fluoride concentration in community water and bottled drinking water: a dilemma today.

PubMed

Dhingra, S; Marya, C M; Jnaneswar, A; Kumar, H

2013-01-01

Because of the potential for contamination of municipal water supplies, people appear to be turning to alternative sources for their pure drinking water. The present study analyzed the fluoride concentration in community water and bottled drinking water sold in Faridabad city. A comparative evaluation of fluoride content in community water supply and bottled drinking water was done using ion-selective electrode method. The community water samples were collected from six different areas (i.e. north zone, south zone, east zone, west zone and central zone) in the city from public health water supply taps while bottled drinking water samples were randomly picked from grocery shops or supermarkets. The fluoride concentration in the community water supply in this study ranges from 0.11 to 0.26 mg/L with mean fluoride concentration of 0.17 mg/L. The mean concentration of fluoride in bottled drinking water was 0.06 mg/L. The differences observed between mean of two water samples was statistically significant. The results obtained from the present study clearly state that the fluoride concentration was insufficient in community water supply from all the areas and also was deficient in bottled drinking water sold in Faridabad city. So, Alternative sources of fluorides should be supplemented for optimal dental benefits from the use of fluoride.

Impact of an Anticaries Mouthrinse on In Vitro Remineralization and Microbial Control

PubMed Central

Sun, Frank C.; Engelman, E. Eric; McGuire, James A.; Kosmoski, Gabrielle; Carratello, Lauren; Ricci-Nittel, Danette; Zhang, Jane Z.; Schemehorn, Bruce R.; Gambogi, Robert J.

2014-01-01

Objective. The objective of this research was to evaluate the caries control potential of a new fluoride mouthrinse that also contained antimicrobial agents and a biofilm disrupting agent using different in vitro models. Methods. Four in vitro studies were conducted to assess the performance of this three pronged approach to caries control: (1) traditional enamel fluoride uptake, (2) surface microhardness study using pH cycling model and subsequent fluoride uptake, (3) a salivary biofilm flow-through study to determine the anti-microbial activity, and (4) a single species biofilm model measuring effect on biofilm matrix disruption. Results. The data showed that a LISTERINE rinse with fluoride, essential oils and xylitol was superior in promoting enamel fluoride uptake and in enhancing antimicrobial activity over traditional commercially available fluoridated products. An increase of the surface microhardness was observed when the LISTERINE rinse was used in combination with fluoridated toothpaste versus the fluoridated toothpaste alone. Finally, it was demonstrated that xylitol solutions disrupted and reduced the biovolume of biofilm matrix of mature Streptococcus mutans. Conclusion. These in vitro studies demonstrated that a fluoride mouthrinse with antimicrobial agent and biofilm matrix disrupting agent provided multifaceted and enhanced anti-caries efficacy by promoting remineralization, reducing acidogenic bacteria and disrupting biofilm matrix. PMID:24648842

URANIUM RECOVERY PROCESS

DOEpatents

Bailes, R.H.; Long, R.S.; Olson, R.S.; Kerlinger, H.O.

1959-02-10

A method is described for recovering uranium values from uranium bearing phosphate solutions such as are encountered in the manufacture of phosphate fertilizers. The solution is first treated with a reducing agent to obtain all the uranium in the tetravalent state. Following this reduction, the solution is treated to co-precipitate the rcduced uranium as a fluoride, together with other insoluble fluorides, thereby accomplishing a substantially complete recovery of even trace amounts of uranium from the phosphate solution. This precipitate usually takes the form of a complex fluoride precipitate, and after appropriate pre-treatment, the uranium fluorides are leached from this precipitate and rccovered from the leach solution.

Method for obtaining oxygen from lunar or similar soil

NASA Technical Reports Server (NTRS)

Downs, W. R. (Inventor)

1973-01-01

Recovery of oxygen from soil containing metal oxides such as alumina, silica, calcia, magnesia, and ilmenite wherein the material containing the oxides is placed in a vessel and reacted with fluorine to provide oxygen and metal fluorides. The oxygen produced from the reaction is recovered and stored, after further purifying processes, and the metal fluorides are further reacted with potassium vapor to provide potassium fluoride and free metals. The potassium fluoride is than subjected to electrolysis whereby the potassium and fluorine are separated and are recycled for further use in the system. Valuable free metals are recovered for other uses.

An easy access to nanocrystalline alkaline earth metal fluorides - just by shaking

NASA Astrophysics Data System (ADS)

Dreger, M.; Scholz, G.; Kemnitz, E.

2012-04-01

High energy ball milling as fast, direct and solvent free method allows an easy access to nanocrystalline alkaline earth metal fluorides MF2 (M: Mg, Ca, Sr, Ba). Comparable metal sources (acetates, carbonates, hydroxides, alkoxides) were used for the reaction with NH4F as fluorinating agent. Even very simple manual shaking experiments between NH4F and the corresponding hydroxides in the stoichiometric ratio (M:F = 1:2, M: Ca, Sr, Ba) give phase pure fluorides. Moreover, comparable classical thermal reactions in closed crucibles at higher temperatures provide phase pure crystalline fluorides in nearly all cases as well.

The costs and benefits of water fluoridation in NZ.

PubMed

Moore, David; Poynton, Matthew; Broadbent, Jonathan M; Thomson, W Murray

2017-11-28

Implementing community water fluoridation involves costs, but these need to be considered against the likely benefits. We aimed to assess the cost-benefit and cost-effectiveness of water fluoridation in New Zealand (NZ) in terms of expenditure and quality-adjusted life years. Based on published studies, we determined the risk reduction effects of fluoridation, we quantified its health benefits using standardised dental indexes, and we calculated financial savings from averted treatment. We analysed NZ water supplies to estimate the financial costs of fluoridation. We devised a method to represent dental caries experience in quality-adjusted life years. Over 20 years, the net discounted saving from adding fluoride to reticulated water supplies supplying populations over 500 would be NZ$1401 million, a nine times pay-off. Between 8800 and 13,700 quality-adjusted life years would be gained. While fluoridating reticulated water supplies for large communities is cost-effective, it is unlikely to be so with populations smaller than 500. Community water fluoridation remains highly cost-effective for all but very small communities. The health benefits-while (on average) small per person-add up to a substantial reduction in the national disease burden across all ethnic and socioeconomic groups.

Influence of sodium fluoride on the synthesis of hydroxyapatite by gel method

NASA Astrophysics Data System (ADS)

Kanchana, P.; Sekar, C.

2010-03-01

Hydroxyapatite (HA) is a good candidate for bone substitutes due to its chemical and structural similarity to bone mineral. Hydroxyapatite has been grown by the gel method using sodium fluoride (NaF) as additive. The growth was carried out at room temperature under the physiological pH of 7.4. The addition of NaF has significantly reduced growth rate and the yield was much less when compared to pure system. The samples of pure and fluoride doped HA were sintered at 600, 900 and 1200 °C in ambient atmosphere. Scanning electron microscopy (SEM), powder X-ray diffraction (XRD), thermogravimetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR) were adopted to investigate the influence of NaF on the morphology, crystallinity, stability and phase purity of HA. EDAX and FTIR studies confirm that the fluoride is doped into the hydroxyapatite. Powder XRD and TGA results suggested that the incorporation of fluorine into the HA matrix improves the phase formation and crystallinity. SEM studies show that the microstructural morphology of HA changes from the fibers for pure to granular structure for the fluoride doped.

Estimated probability of arsenic in groundwater from bedrock aquifers in New Hampshire, 2011

USGS Publications Warehouse

Ayotte, Joseph D.; Cahillane, Matthew; Hayes, Laura; Robinson, Keith W.

2012-01-01

The statewide maps generated by the probability models are not designed to predict arsenic concentration in any single well, but they are expected to provide useful information in areas of the State that currently contain little to no data on arsenic concentration. They also may aid in resource decision making, in determining potential risk for private wells, and in ecological-level analysis of disease outcomes. The approach for modeling arsenic in groundwater could also be applied to other environmental contaminants that have potential implications for human health, such as uranium, radon, fluoride, manganese, volatile organic compounds, nitrate, and bacteria.

Associations between fluorosis of permanent incisors and fluoride intake from infant formula, other dietary sources and dentifrice during early childhood

PubMed Central

Levy, Steven M.; Broffitt, Barbara; Marshall, Teresa A.; Eichenberger-Gilmore, Julie M.; Warren, John J.

2017-01-01

Objectives The authors describe associations between dental fluorosis and fluoride intakes, with an emphasis on intake from fluoride in infant formula. Methods The authors administered periodic questionnaires to parents to assess early fluoride intake sources from beverages, selected foods, dentifrice and supplements. They assessed relationships between fluorosis of the permanent maxillary incisors and fluoride intake from beverages and other sources, both for individual time points and cumulatively using area-under-the-curve (AUC) estimates. The authors determined effects associated with fluoride in reconstituted powdered infant formulas, along with risks associated with intake of fluoride from dentifrice and other sources. Results Considering only fluoride intake from age 3 to 9 months, the authors found that participants with fluorosis (97 percent of which was mild) had significantly greater cumulative fluoride intake (AUC) from reconstituted powdered infant formula, other beverages with added water or a combination of these than did those without fluorosis. For participants aged 16 to 36 months, participants with fluorosis had significantly higher fluoride intake from water by itself, dentifrice or a combination of these than did those without fluorosis. In a model combining both the 3- to 9-month and 16- to 36-months age groups, the significant variables were fluoride intake from reconstituted powder concentrate formula (by participants aged 3–9 months), other beverages with added water (also by participants aged 3–9 months) and dentifrice (by participants aged 16–36 months). Conclusions Greater fluoride intakes from reconstituted powdered formulas (when participants were aged 3–9 months) and other water-added beverages (when participants were aged 3–9 months) increased fluorosis risk as did higher dentifrice intake by participants when aged 16 to 36 months. Clinical Implications Results suggest that prevalence of mild dental fluorosis could be reduced by avoiding ingestion of large quantities of fluoride from reconstituted powdered concentrate infant formula and fluoridated dentifrice. PMID:20884921

Changing risk factors for fluorosis among South Australian children.

PubMed

Spencer, A John; Do, Loc G

2008-06-01

Research in the last decade has shown changing exposure patterns to discretionary fluorides and declining prevalence of fluorosis among South Australian children, raising the question of how risk factors for fluorosis have changed. To examine and compare risk factors for fluorosis among representative samples of South Australian children in 1992/1993 and 2002/2003. Similar sampling strategies and data collection methods were employed in the Child Fluoride Study (CFS) Marks 1 (1992/1993) and 2 (2002/2003). Participants in each CFS round were examined for fluorosis using the Thylstrup and Fejerskov (TF) Index. Exposure history was collected for fluoride in water, toothpaste, fluoride supplements and infant formula, allowing for a fluorosis risk assessment analysis. Data were re-weighted to represent the child population at each time. Changes in prevalence of fluorosis, defined as having a TF score of 1+ on maxillary central incisors, fluoride exposure and risk factors between the two rounds were evaluated. A total of 375 and 677 children participated in the 1992/1993 and 2002/2003 rounds respectively. Prevalence of fluorosis declined significantly from 45.3% to 25.9%. Reduced use of fluoride supplements and increased use of 400-550-ppm children F toothpaste were the most substantial fluoride exposure changes. Early toothpaste use, residence in fluoridated areas and fluoride supplement use were the risk factors in 1992/1993. Early toothpaste use and fluoride supplement use were not risk factors, leaving fluoridated water as the only risk factor among the common variables in 2002/2003. In an analysis stratified by the type of fluoridated toothpaste in 2002/2003, the large amount of toothpaste used was a risk factor in those who used 1000-ppm fluoridated toothpaste, and eating/licking toothpaste when toothpaste use started was a risk factor among children who used either 1000-ppm or 400-550-ppm fluoridated toothpaste. Introduction of the 400-550-ppm F toothpaste and use of smaller amount of toothpaste restricted risk associated with early toothpaste use. Less use and possibly a stricter fluoride supplements regimen also restricted fluorosis risk. Periodic monitoring of risk of fluorosis is required to adjust guidelines for fluoride use in caries prevention.

Periodontal health status among permanent residents of low, optimum and high fluoride areas in Kolar District, India.

PubMed

Megalamanegowdru, Jayachandra; Ankola, Anil V; Vathar, Jagadishchandra; Vishwakarma, Prashanthkumar; Dhanappa, Kirankumar B; Balappanavar, Aswini Y

2012-01-01

To assess and compare the periodontal health status among permanent residents of low, optimum and high fluoride areas in Kolar District, India. A house-to-house survey was conducted in a population consisting of 925 permanent residents aged 35 to 44 years in three villages having different levels of fluoride concentrations in the drinking water. The fluoride concentrations in selected villages were 0.48 ppm (low), 1.03 ppm (optimum) and 3.21 ppm (high). The ion selective electrode method was used to estimate the fluoride concentration in the drinking water. Periodontal status was assessed using the Community Periodontal Index (CPI) and loss of attachment (LOA). Results were analysed using the chi-square test and logistic regression. The chi-square test was used to find the group differences and logistic regression to find association between the variables. The overall prevalence of periodontitis was 72.9%; specifically, prevalences were 95.4%, 76.3% and 45.7% in low, optimum and high fluoride areas, respectively. The number of sextants with shallow or deep pockets decreased (shallow pockets: 525, 438, 217; deep pockets: 183, 81, 34) from low to high fluoride areas (odds ratio: 71.3). The low fluoride area had a 7.9-fold higher risk of periodontitis than the optimum fluoride area and a 30-fold higher risk than the high fluoride area, which was highly significant (χ2 = 53.5, P < 0.0001 and χ2 = 192.8, P < 0.001, respectively). The severity of periodontal disease is inversely associated with the fluoride concentrations in drinking water. This relation can provide an approach to fluoride treatments to reduce the prevalence or incidence of this disease.

Prevalence of dental fluorosis & dental caries in association with high levels of drinking water fluoride content in a district of Gujarat, India

PubMed Central

Kotecha, P.V.; Patel, S.V.; Bhalani, K.D.; Shah, D.; Shah, V.S.; Mehta, K.G.

2012-01-01

Background & objectives: Endemic fluorosis resulting from high fluoride concentration in groundwater is a major public health problem in India. This study was carried out to measure and compare the prevalence of dental fluorosis and dental caries in the population residing in high and normal level of fluoride in their drinking water in Vadodara district, Gujarat, India. Methods: A cross-sectional study was conducted in Vadodara district, six of the 261 villages with high fluoride level and five of 1490 with normal fluoride level in drinking water were selected. The data collection was made by house-to-house visits twice during the study period. Results: The dental fluorosis prevalence in high fluoride area was 59.31 per cent while in normal fluoride area it was 39.21 per cent. The prevalence of dental caries in high fluoride area was 39.53 per cent and in normal fluoride area was 48.21 per cent with CI 6.16 to 11.18. Dental fluorosis prevalence was more among males as compared to females. Highest prevalence of dental fluorosis was seen in 12-24 yr age group. Interpretation & conclusions: The risk of dental fluorosis was higher in the areas showing more fluoride content in drinking water and to a lesser degree of dental caries in the same area. High fluoride content is a risk factor for dental fluorosis and problem of dental fluorosis increased with passage of time suggesting that the fluoride content in the water has perhaps increased over time. Longitudinal studies should be conducted to confirm the findings. PMID:22825606

Mus musculus bone fluoride concentration as a useful biomarker for risk assessment of skeletal fluorosis in volcanic areas.

PubMed

Linhares, Diana; Camarinho, Ricardo; Garcia, Patrícia Ventura; Rodrigues, Armindo Dos Santos

2018-08-01

Fluoride is often found in elevated concentrations in volcanic areas due to the release of magmatic fluorine as hydrogen fluorine through volcanic degassing. The exposure to high levels of fluoride can affect the processes of bone formation and resorption causing skeletal fluorosis, a pathology that can easily be mistaken for other skeletal diseases. In this study, we aimed to determine if fluoride concentration in the femoral bone of wild populations of the house mouse (Mus musculus) is a good biomarker of exposure to active volcanic environments naturally enriched in fluoride, allowing their use in biomonitoring programs. The fluoride concentration of the whole femoral bone of 9 mice from Furnas (5 males and 4 females) and 33 mice from Rabo de Peixe (16 males and 17 females) was measured by the potentiometric method with a fluoride ion selective electrode. Fluoride in bones was significantly higher in the mice from Furnas when compared with the mice from Rabo de Peixe (616.5 ± 129.3 μg F/g vs. 253.8 ± 10.5 μg F/g). Accumulation rates were also significantly higher in the mice collected in Furnas when compared with Rabo de Peixe individuals (3.84 ± 0.52 μg F/day vs. 1.22 ± 0.06 μg F/day). The results demonstrate a significant association between exposure to fluoride in the active volcanic environment and fluoride content in bone, revealing that bone fluoride concentration is a suitable biomarker of chronic environmental exposure to fluoride. Copyright © 2018 Elsevier Ltd. All rights reserved.

Prevalence of Brick Tea-Type Fluorosis in the Tibet Autonomous Region.

PubMed

Fan, Zhipeng; Gao, Yanhui; Wang, Wei; Gong, Hongqiang; Guo, Min; Zhao, Shengcheng; Liu, Xuehui; Yu, Bing; Sun, Dianjun

2016-01-01

The prevalence of brick tea-type fluorosis is high in Tibet because of the habit of drinking brick tea in this region. Brick tea-type fluorosis has become an urgent public health problem in China. A cross-sectional survey was conducted to investigate prevalence of brick tea-type fluorosis in all districts of Tibet using a stratified cluster sampling method. Dental fluorosis in children aged 8-12 years and clinical skeletal fluorosis in adults were diagnosed according to the national criteria. A total of 423 children and 1320 adults participated in the study. Samples of drinking water, brick tea, brick tea infusion (or buttered tea), and urine were collected and measured for fluoride concentrations by the fluoride ion selective electrode method. The fluoride level in all but one of the brick tea samples was above the national standard. The average daily fluoride intake from drinking brick tea in all seven districts in Tibet was much higher than the national standard. The prevalence of dental fluorosis was 33.57%, and the prevalence of clinical skeletal fluorosis was 46.06%. The average daily fluoride intake from drinking brick tea (r = 0.292, P < 0.05), urine fluoride concentrations in children (r = 0.134, P < 0.05), urine fluoride concentrations in adults (r = 0.162, P < 0.05), and altitude (r = 0.276, P < 0.05) were positively correlated with the prevalence of brick tea-type fluorosis. Herdsmen had the highest fluoride exposure and the most severe skeletal fluorosis. Brick tea-type fluorosis in Tibet is more serious than in other parts of China. The altitude and occupational factors are important risk factors for brick tea-type fluorosis.

Correlation between Fluoride in Drinking Water and Its Levels in Breast Milk in Golestan Province, Northern Iran.

PubMed

Faraji, Hossein; Mohammadi, Ali Akbar; Akbari-Adergani, Behrouz; Vakili Saatloo, Naimeh; Lashkarboloki, Gholamreza; Mahvi, Amir Hossein

2014-12-01

Fluoride is an essential element for human health. However, excess fluoride in drinking water may cause dental and/or skeletal fluorosis. Drinking water is the main route of fluoride intake. The aim of the present study was to measure fluoride levels in human breast milk collected from two regions of Golestan Province, northern Iran with different amount of fluoride concentration of drinking water in Bandar Gaz and Nokande cities and to correlate it with fluoride concentrations in drinking water used by mothers living in these two areas. Twenty samples of water were collected from seven drinking water wells during 2012 from Bandar Gaz and Nokande in Iran during 2012. Fluoride concentration of water samples was measured using SPADNS method. Sixty breast milk samples were collected from lactating mothers of Bandar Gaz and Nokande cities. Content in breast milk was determined using standard F ion-selective electrode. Spearman's rho correlation analysis was used to assess any possible relationship between fluoride levels in breast milk and in drinking water. The means and standard deviation for F concentration in breast milk and drinking water were 0.002188±0.00026224 ppm and 0.5850±0.22542 ppm, respectively. Analysis of data showed that the variables were not normally distributed so the Spearman correlation coefficient between two variables calculated (ρ S = 0.65) and it was significant (P=0.002). Fluoride concentration in water can directly act on its concentration in breast milk. We speculate that modifying F concentration in water can affect accessibility of fluoride for infants.

Effects of sodium fluoride on MAPKs signaling pathway in the gills of a freshwater teleost, Cyprinus carpio.

PubMed

Cao, Jinling; Chen, Jianjie; Wang, Jundong; Klerks, Paul; Xie, Lingtian

2014-07-01

Exposure to elevated levels of fluoride can cause a variety of adverse effects in fish. Previously we showed that fluoride causes injuries and apoptosis in the gills of Cyprinus carpio. In this study, the effects of fluoride on caspase-3 activity and on accumulation of proteins in the MAPKs pathways were evaluated using Western blotting and immunohistochemistry methods in vivo and in vitro. In vivo experiments showed that the caspase-3 activity increased with fluoride exposure level in a dose-dependent pattern Western blotting and immunohistochemistry results indicated that ERK relative activation tended to decrease as a function of fluoride exposure concentration. In contrast, relative activation of JNK increased with fluoride exposure level. Fluoride exposure did not appear to affect p38 activation. Furthermore, pretreatment of branchial cells with MAPK-specific inhibitors effectively prevented JNK induction and ERK inhibition, respectively, as well as reversed caspase-3 activity in fluoride-treated branchial cells. Our results indicate that activation of JNK and inactivation of ERK were caused by increased ROS and decreased antioxidant capacity in the gills of chronically exposed C. carpio described previously, which eventually caused the observed apoptosis in the fluoride-exposed gills and cells in C. carpio. JNK activation and ERK inactivation mechanism play a crucial role in gill impairment induced by chronic fluorosis. These findings contribute to a better understanding of the initial molecular and cellular events in the gill of fish chronically exposed to fluoride. Copyright © 2014 Elsevier B.V. All rights reserved.

Method for decontamination of nickel-fluoride-coated nickel containing actinide-metal fluorides

DOEpatents

Windt, Norman F.; Williams, Joe L.

1983-01-01

The invention is a process for decontaminating particulate nickel contaminated with actinide-metal fluorides. In one aspect, the invention comprises contacting nickel-fluoride-coated nickel with gaseous ammonia at a temperature effecting nickel-catalyzed dissociation thereof and effecting hydrogen-reduction of the nickel fluoride. The resulting nickel is heated to form a melt and a slag and to effect transfer of actinide metals from the melt into the slag. The melt and slag are then separated. In another aspect, nickel containing nickel oxide and actinide metals is contacted with ammonia at a temperature effecting nickel-catalyzed dissociation to effect conversion of the nickel oxide to the metal. The resulting nickel is then melted and separated as described. In another aspect nickel-fluoride-coated nickel containing actinide-metal fluorides is contacted with both steam and ammonia. The resulting nickel then is melted and separated as described. The invention is characterized by higher nickel recovery, efficient use of ammonia, a substantial decrease in slag formation and fuming, and a valuable increase in the service life of the furnace liners used for melting.

Topical Iodine And Fluoride Varnish Combined Is More Effective Than Fluoride Varnish Alone For Protecting Erupting First Permanent Molars: A Retrospective Cohort Study

PubMed Central

Tut, Ohnmar K.; Milgrom, Peter M.

2010-01-01

Objective This communication examines the combined effect of topical PVP-iodine plus fluoride varnish in prevention of tooth decay in erupting first permanent molars in an on-going public health program. Methods The evaluation employed a retrospective cohort design with two groups of children 60–83 months. Cohort 1 (2004–05) received three times per school year topical fluoride varnish, and Cohort 2 (2008–09) received topical application of 10% PVP-iodine followed at each visit with topical fluoride varnish. The children were examined clinically at the beginning and end of the school year. Results The proportion of children with caries-free first permanent molars in Cohort 2 (PVP-iodine plus fluoride varnish) was .883 and was greater than that in Cohort 1 (varnish), which was .785 (Chi-square=1.000E1, df 1, p<.002). Conclusions This evaluation of an on-going dental public health program adds evidence that topical antiseptics applied at the same time as fluoride varnish are more effective than varnish alone. Randomized trials are needed. PMID:20337902

Process for producing a clean hydrocarbon fuel from high calcium coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kindig, J.K.

A method is described for substantially reducing the amount of at least one insoluble fluoride-forming species selected from the group consisting of Group IA species and Group IIA species. The species is present in a coal feed material comprising: forming a slurry of a coal feed; a fluoride acid in an amount to produce a first molar concentration of free-fluoride-ions; at least one fluoride-complexing species, the total of all fluoride-complexing species in the slurry being present in an amount to produce a second molar concentration, the second molar concentration being at least equal to that amount such that the ratiomore » of the first molar concentration to the second molar concentration is substantially equal to the stoichiometric ratio of fluoride in at least one tightly-bound complexion so as to from tightly-bound complexions with substantially all free-fluoride ions in the slurry to produce a leached coal product and a spent leach liquor; and separating the leached coal product from the spent leach liquor.« less

Effect of Three Clinical Curing Treatments on Fluoride Release and Surface Hardness of Glass-Ionomer Cements.

PubMed

Dionysopoulos, Dimitrios; Tolidis, Kosmas; Gerasimou, Paris; Sfeikos, Thrasyvoulos

The purpose of this study was to investigate the effect of radiant heat, ultrasonic treatment, and 42.7 wt% CaCl₂ solution on fluoride release and surface hardness in three conventional glass-ionomer cements (GICs). The fluoride release patterns of each GIC were evaluated during a 28-day period using a fluoride ion-selective electrode. The surface hardness of the tested GICs was evaluated 24 hours after preparation of the specimens using Vickers hardness test. Statistical analysis of the data was made using analysis of variance and Bonferroni post hoc test (α = .05). Radiant heat, ultrasonic, and CaCl₂ solution treatments reduced fluoride release and increased the surface hardness of the tested GICs (P < .05). Among the tested GICs, differences in fluoride release and surface hardness were observed (P < .05). The clinical treatments investigated may be effective methods for improving the setting reaction of GICs and may achieve sufficient initial mechanical properties earlier. Although a reduction in fluoride release occurs after the treatments, anticariogenic properties of the GICs may not be significantly affected.

Seasonal Variation in Fluoride Content in Groundwaters of Langtang Area, Northcentral Nigeria

NASA Astrophysics Data System (ADS)

Dibal, H. U.; Dajilak, W. N.; Lekmang, I. C.; Nimze, L. W.; Yenne, E. Y.

2017-06-01

Thirty groundwater samples were collected at the peak of the rainy season and analysed for fluoride and other cations and anions in drinking water sources of Langtang area. For comparative purposes, thirty seven groundwater samples were collected in the dry season. The aim of the study was to determine variation in fluoride content with respect to the seasons. Fluoride in water was determined by the Ion Selective Electrode (ISE) and the cations by the Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). The anion (sulphate) was determined by Multi - Ion Colorimeter, bicarbonate and chloride by titration method. In addition fluorine content in aquifer materials from a borehole section were determined by Fusion method. The two seasons show variation in content of fluoride in groundwater. Fluoride content in groundwater is higher in the dry season ranging from 0.13 - 10.3 mg/l compared to the 0.06 - 4.60 mg/l values in the rainy season. Content of fluorine (0.01 wt %) in the aquifer materials (sands) is low from depth of 0 to 7.95 m. However, fluorine content increases with depth, from 7.95 to 10.60 m with concentration of 0.04 wt %, 0.05 wt % from 10.60 to 13.25m, and 0.07 wt % from 13.25 to 15.70 m, the content of fluorine however, decreased at depth 15.70 to18.55m with concentration of 0.02 wt % even with fluorite mineral in the aquifer material at this depth. Dilution of fluoride ion as a result of rain input which recharges the aquifer may be the main reason for lower values recorded in the rainy season. Over fifty and sixty percent of waters in both dry and rainy season have fluoride concentration above the WHO upper limit of 1.5 mg/l. Consumption of these elevated values of fluoride in groundwater of the study area, clearly manifests as symptoms of dental fluorosis.

Method for the recovery of uranium values from uranium tetrafluoride

DOEpatents

Kreuzmann, Alvin B.

1983-01-01

The invention is a novel method for the recovery of uranium from dry, particulate uranium tetrafluoride. In one aspect, the invention comprises reacting particulate uranium tetrafluoride and calcium oxide in the presence of gaseous oxygen to effect formation of the corresponding alkaline earth metal uranate and alkaline earth metal fluoride. The product uranate is highly soluble in various acidic solutions wherein the product fluoride is virtually insoluble therein. The product mixture of uranate and alkaline earth metal fluoride is contacted with a suitable acid to provide a uranium-containing solution, from which the uranium is recovered. The invention can achieve quantitative recovery of uranium in highly pure form.

Method for the recovery of uranium values from uranium tetrafluoride

DOEpatents

Kreuzmann, A.B.

1982-10-27

The invention is a novel method for the recovery of uranium from dry, particulate uranium tetrafluoride. In one aspect, the invention comprises reacting particulate uranium tetrafluoride and calcium oxide in the presence of gaseous oxygen to effect formation of the corresponding alkaline earth metal uranate and alkaline earth metal fluoride. The product uranate is highly soluble in various acidic solutions whereas the product fluoride is virtually insoluble therein. The product mixture of uranate and alkaline earth metal fluoride is contacted with a suitable acid to provide a uranium-containing solution, from which the uranium is recovered. The invention can achieve quantitative recovery of uranium in highly pure form.

Periodic health examination, 1995 update: 2. Prevention of dental caries. The Canadian Task Force on the Periodic Health Examination.

PubMed Central

Lewis, D W; Ismail, A I

1995-01-01

OBJECTIVE: To make recommendations, based on current evidence, for practising physicians and dentists on interventions for the prevention of dental caries in their patients. OPTIONS: Systemic fluoride administration, professionally administered fluoride, use of fluoride mouth rinses, fissure sealants, oral-hygiene practices, dietary practices, identification of groups at a high risk of dental caries, and early diagnosis and treatment. OUTCOMES: Reduced prevalence of dental caries and fluorosis, longer retention of teeth and lower treatment costs. EVIDENCE: Several MEDLINE searches were conducted for articles published from January 1980 to December 1992, including relevant review articles. VALUES: Relevant clinical findings were evaluated and categorized with the use of the evidence-based methods and values of the Canadian Task Force on the Periodic Health Examination. Recommendations were developed for each method of caries prevention, with reduced incidence of dental caries and improved prevalence of caries-free teeth given high values. BENEFITS, HARMS AND COSTS: The potential benefits of these measures in the long-term are a lower incidence of tooth decay, longer retention of teeth and prevention of fluorosis. The cost saving can be considerable for patients and insurers; however, implementation of some recommendations will be difficult, since the traditional preventive practices of dentists and dental hygienists are not easily changed. RECOMMENDATIONS: There is good evidence that the following manoeuvres are effective in preventing dental caries: use of dentifrices containing fluoride, fluoridation of drinking water, fluoride supplements for patients in areas where there is a low level (0.3 ppm or less) of fluoride in the drinking water, professionally applied topical fluoride and the use of fluoride mouth rinses for patients with very active decay or at a high risk of dental caries and selective use of professionally applied fissure sealants on permanent molar teeth. There is poor evidence that the following manoeuvres are effective in preventing dental caries: professionally applied topical fluoride and the use of fluoride mouth rinses for patients with a low risk of caries, toothbrushing (without a dentifrice containing fluoride) and flossing, cleaning of teeth by a dentist or dental hygienist before topical application of fluoride or at a dental visit and dietary counselling for the general population. There is good evidence to recommend against the use of over-the-counter fluoride mouth rinses by the general population. VALIDATION: These guidelines are compatible with those of the US Preventive Services Task Force. SPONSOR: These guidelines were developed and endorsed by the task force, which is funded by Health Canada. Major funding was provided by the Faculty of Dentistry of the University of Toronto, Toronto and the Faculty of Dentistry of Dalhousie University, Halifax. PMID:7697577

Drinking water fluoride levels for a city in northern Mexico (durango) determined using a direct electrochemical method and their potential effects on oral health.

PubMed

Molina Frechero, Nelly; Sánchez Pérez, Leonor; Castañeda Castaneira, Enrique; Oropeza Oropeza, Anastasio; Gaona, Enrique; Salas Pacheco, José; Bologna Molina, Ronell

2013-01-01

Fluoride is ingested primarily through consuming drinking water. When drinking water contains fluoride concentrations>0.7 parts per million (ppm), consuming such water can be toxic to the human body; this toxicity is called "fluorosis." Therefore, it is critical to determine the fluoride concentrations in drinking water. The objective of this study was to determine the fluoride concentration in the drinking water of the city of Durango. The wells that supply the drinking water distribution system for the city of Durango were studied. One hundred eighty-nine (189) water samples were analyzed, and the fluoride concentration in each sample was quantified as established by the law NMX-AA-077-SCFI-2001. The fluoride concentrations in such samples varied between 2.22 and 7.23 ppm with a 4.313±1.318 ppm mean concentration. The highest values were observed in the northern area of the city, with a 5.001±2.669 ppm mean value. The samples produced values that exceeded the national standard for fluoride in drinking water. Chronic exposure to fluoride at such concentrations produces harmful health effects, the first sign of which is dental fluorosis. Therefore, it is essential that the government authorities implement water defluoridation programs and take preventative measures to reduce the ingestion of this toxic halogen.

Drinking Water Fluoride Levels for a City in Northern Mexico (Durango) Determined Using a Direct Electrochemical Method and Their Potential Effects on Oral Health

PubMed Central

Molina Frechero, Nelly; Sánchez Pérez, Leonor; Castañeda Castaneira, Enrique; Oropeza Oropeza, Anastasio; Gaona, Enrique; Salas Pacheco, José; Bologna Molina, Ronell

2013-01-01

Fluoride is ingested primarily through consuming drinking water. When drinking water contains fluoride concentrations >0.7 parts per million (ppm), consuming such water can be toxic to the human body; this toxicity is called “fluorosis.” Therefore, it is critical to determine the fluoride concentrations in drinking water. The objective of this study was to determine the fluoride concentration in the drinking water of the city of Durango. The wells that supply the drinking water distribution system for the city of Durango were studied. One hundred eighty-nine (189) water samples were analyzed, and the fluoride concentration in each sample was quantified as established by the law NMX-AA-077-SCFI-2001. The fluoride concentrations in such samples varied between 2.22 and 7.23 ppm with a 4.313 ± 1.318 ppm mean concentration. The highest values were observed in the northern area of the city, with a 5.001 ± 2.669 ppm mean value. The samples produced values that exceeded the national standard for fluoride in drinking water. Chronic exposure to fluoride at such concentrations produces harmful health effects, the first sign of which is dental fluorosis. Therefore, it is essential that the government authorities implement water defluoridation programs and take preventative measures to reduce the ingestion of this toxic halogen. PMID:24348140

Dental Fluorosis and Dental Caries Prevalence among 12 and 15-Year-Old School Children in Nalgonda District, Andhra Pradesh, India

PubMed Central

Sukhabogi, JR; Parthasarathi, P; Anjum, S; Shekar, BRC; Padma, CM; Rani, AS

2014-01-01

Background: Fluoride is a double edged sword. The assessment of dental caries and fluorosis in endemic fluoride areas will facilitate in assessing the relation between fluoride concentrations in water with dental caries, dental fluorosis simultaneously. Aim: The objective of the following study is to assess the dental caries and dental fluorosis prevalence among 12 and 15-year-old school children in Nalgonda district, Andhra Pradesh, India. Subjects and Methods: This was a cross-sectional study. Two stage cluster sampling technique was employed to select 20 schools from Nalgonda district. The oral examination of available 12 and 15-year-old children fulfilling the inclusion and exclusion criteria was carried out to assess dental caries and fluorosis. The examination was conducted by a single trained and calibrated examiner using the mouth mirror and community periodontal index probe under natural daylight. These areas were divided into four categories, low, medium, high and very high fluoride areas based on the fluoride concentration at the time of statistical analysis. The data was analyzed using Statistical Package for the Social Sciences version 16 (IBM, Chicago, USA). Results: The caries prevalence was less among 12-year-old children (39.9% [369/924]) compared with 15-years-old children (46.7% [444/951]). The prevalence was more among females (50.4% [492/977]) than males (35.8% [321/898]). The prevalence was more in low fluoride area (60.5% [300/496]) followed by very high fluoride area (54.8% [201/367]), high fluoride area (32.4% [293/904]) and medium fluoride area (17.6% [19/108]) in the descending order. The fluorosis prevalence increased with increasing fluoride concentration with no difference in gender and age distribution. Conclusion: Low fluoride areas require fluoridation or alternate sources of fluoride, whereas high fluoride areas require defluoridation. Defluoridation of water is an immediate requirement in areas with fluoride concentration of 4 parts per million and above as dental fluorosis is a public health problem in these areas with 100% prevalence. PMID:25364597

Histopathological changes of renal tissue following sodium fluoride administration in two consecutive generations of mice. Correlation with the urinary elimination of fluoride.

PubMed

Dimcevici Poesina, Nicoleta; Bălălău, Cristian; Nimigean, Vanda Roxana; Nimigean, Victor; Ion, Ion; Baconi, Daniela; Bârcă, Maria; Băran Poesina, Violeta

2014-01-01

The present study was designed to investigate the toxic effects (evaluated as histopathological changes) of sodium fluoride on the kidney in two consecutive generations of NMRI mice. An attempt to correlate the toxicity with the urinary elimination of fluoride has been made, as urinary fluoride excretion has been widely used as an indicator of fluoride intake and exposure. Six mixed (males and females) animal groups have been constituted by dividing the populations of mice derived from pregnant females (named "mothers" 0.5 mg sodium fluoride) treated with 0.5 mg sodium fluoride by daily gavage and pregnant females (named "mothers" 0.25 mg sodium fluoride) treated with 0.25 mg sodium fluoride by daily gavage; three types of sodium fluoride treatments were administrated: homeopathic, allopathic-homeopathic and allopathic. When the animals reached the adulthood, by randomization, they were selected in pairs for giving birth to the second generation of mice. No treatments were administrated to the second generation of mice; thus, the urinary elimination of fluoride in the second generation is attributed to exposure at sodium fluoride before birth. The administration of sodium fluoride to the first generation (F1) is realized until the mice reached the adulthood. For the first generation, the urine was collected at three times, every three weeks: at the age of four weeks, seven weeks and 11 weeks; single sampling urine, at the age of four weeks, has been conducted for the second generation. The urine samples have been analyzed using the ion selective electrode method for fluoride. For the histopathological examination, the animals were killed by cervical dislocation; the kidneys were collected in a 10% formalin solution. The preparation of samples for optical microscopy was realized with Hematoxylin-Eosin staining. The results indicate that the elimination of fluoride was similar (at the second evaluation, at 7-week-old of the first generation) for the both generations of mice. Histopathological observation of the kidney has revealed granular dystrophy of the renal tubules, necrosis of the endothelial cells and of the mesangial cells of renal glomerulus. The study indicates that different sodium fluoride treatments produce some pathological aspects of the kidneys and influence the urinary elimination of fluoride in two consecutive generations of mice. For the higher doses, the pathological changes of the kidney are more important, and the urinary elimination of fluoride is higher, especially for the allopathic doses.

Successes and drawbacks in the caries-preventive use of fluorides--lessons to be learnt from history.

PubMed

Marthaler, T M

2003-01-01

Water fluoridation was the first breakthrough in the practice of preventive cariology on a community level and has remained one of the cornerstones of prevention in dentistry. The concepts regarding the mechanisms of the caries-inhibitory effect, however, have changed in several respects. Today there is general agreement that topical effects on the erupted enamel are most important. The contention that there is no pre-eruptive effect whatsoever has created confusion; there is in fact evidence for a minor pre-eruptive protective effect. Around 1980 many experts believed that fluorides should not be used in high concentrations, for instance above those in dentifrices, because this could block remineralisation in the body of pre-cavity lesions. However, it is now known that such undesirable effects are negligible or non-existent. In the fifties and sixties, fluoride tablets were widely used in Europe and helped to make the concept of caries prevention popular. From 1980 onwards, fluoride dentifrices were found to have a much greater impact and were recognized as being able to lead to a decline of caries prevalence in entire countries, and fluoride tablets gradually lost their importance. Antifluoridationists were unable to delay or hinder the widespread use of fluoride toothpastes but in many cases have successfully opposed public health measures such as fluoridation of water or of salt. The spread of these methods, beneficial for all social strata, might have been more rapid if some of the experts had not propounded the erroneous supposition that fluoride dentifrice will be sufficient for caries prevention. Sale of fluoridated salt has been authorized in several countries on a nationwide scale. However, only Latin American countries have introduced salt fluoridation for entire populations. In Central and Eastern Europe where caries prevalence continues to be high and where the level of usage of topical fluorides including dentifrices will presumably remain at a low level for many years, salt fluoridation would be beneficial.

Feasibility and costs of water fluoridation in remote Australian Aboriginal communities

PubMed Central

Ehsani, Jonathon P; Bailie, Ross

2007-01-01

Background Fluoridation of public water supplies remains the key potential strategy for prevention of dental caries. The water supplies of many remote Indigenous communities do not contain adequate levels of natural fluoride. The small and dispersed nature of communities presents challenges for the provision of fluoridation infrastructure and until recently smaller settlements were considered unfavourable for cost-effective water fluoridation. Technological advances in water treatment and fluoridation are resulting in new and more cost-effective water fluoridation options and recent cost analyses support water fluoridation for communities of less than 1,000 people. Methods Small scale fluoridation plants were installed in two remote Northern Territory communities in early 2004. Fluoride levels in community water supplies were expected to be monitored by local staff and by a remote electronic system. Site visits were undertaken by project investigators at commissioning and approximately two years later. Interviews were conducted with key informants and documentation pertaining to costs of the plants and operational reports were reviewed. Results The fluoridation plants were operational for about 80% of the trial period. A number of technical features that interfered with plant operation were identified and addressed though redesign. Management systems and the attitudes and capacity of operational staff also impacted on the effective functioning of the plants. Capital costs for the wider implementation of these plants in remote communities is estimated at about $US94,000 with recurrent annual costs of $US11,800 per unit. Conclusion Operational issues during the trial indicate the need for effective management systems, including policy and funding responsibility. Reliable manufacturers and suppliers of equipment should be identified and contractual agreements should provide for ongoing technical assistance. Water fluoridation units should be considered as a potential priority component of health related infrastructure in at least the larger remote Indigenous communities which have inadequate levels of natural fluoride and high levels of dental caries. PMID:17555604

Effect of CO2 Laser and Fluoride Varnish Application on Microhardness of Enamel Surface Around Orthodontic Brackets

PubMed Central

Mahmoudzadeh, Majid; Rezaei-Soufi, Loghman; Farhadian, Nasrin; Jamalian, Seyed Farzad; Akbarzadeh, Mahdi; Momeni, Mohammadali; Basamtabar, Masome

2018-01-01

Introduction: Orthodontic treatment has many advantages such as esthetic improvement and self-esteem enhancement; yet it has some disadvantages such as increasing the risk of formation of white spot lesions, because it makes oral hygiene more difficult. It is rational to implement procedures to prevent these lesions. The present study was aimed to assess the effect of CO2 laser and fluoride varnish on the surface of the enamel surface microhardness around the orthodontic braces. Methods: Eighty extracted premolar teeth were selected, scaled, polished with nonfluoridated pumic and metal brackets were bonded to them. Then, they were randomly allocated to 5 groups: control (neither fluoride nor laser is used on enamel surfaces), fluoride (4 minutes fluoride varnish treatment of the enamel surfaces), CO2 laser (10.6 µm CO2 laser irradiation of the teeth), laserfluoride (fluoride application after laser irradiation) and fluoride-laser (fluoride was applied and then teeth were irradiated with laser). After surface treatment around brackets on enamel, the samples were stored in 0.1% thymol for less than 5 days and then they were exposed to a 10-day microbiological caries model. Microhardness values of enamel were evaluated with Vickers test. One sample of each group (5 teeth from 80 samples) was prepared for SEM (scanning electron microscopy) and the data from 75 remaining teeth were analyzed with analysis of variance (ANOVA) and chi-square tests (α =0.05). Results: Microhardness mean values from high to low were as follow: fluoride-laser, laser-fluoride, laser, fluoride and control. Microhardness in fluoride-laser group was significantly higher compared with that of the control group. Distribution adhesive remnant index (ARI) scores were significantly different between groups and most of bond failures occurred at the enamel-adhesive interface in groups 2 to 5 and at the adhesive-bracket interface in the control group. Conclusion: Combination of fluoride varnish and CO2 laser irradiation can reduce enamel demineralization around orthodontic brackets. PMID:29399311

Effect of CO2 Laser and Fluoride Varnish Application on Microhardness of Enamel Surface Around Orthodontic Brackets.

PubMed

Mahmoudzadeh, Majid; Rezaei-Soufi, Loghman; Farhadian, Nasrin; Jamalian, Seyed Farzad; Akbarzadeh, Mahdi; Momeni, Mohammadali; Basamtabar, Masome

2018-01-01

Introduction: Orthodontic treatment has many advantages such as esthetic improvement and self-esteem enhancement; yet it has some disadvantages such as increasing the risk of formation of white spot lesions, because it makes oral hygiene more difficult. It is rational to implement procedures to prevent these lesions. The present study was aimed to assess the effect of CO 2 laser and fluoride varnish on the surface of the enamel surface microhardness around the orthodontic braces. Methods: Eighty extracted premolar teeth were selected, scaled, polished with nonfluoridated pumic and metal brackets were bonded to them. Then, they were randomly allocated to 5 groups: control (neither fluoride nor laser is used on enamel surfaces), fluoride (4 minutes fluoride varnish treatment of the enamel surfaces), CO 2 laser (10.6 µm CO 2 laser irradiation of the teeth), laserfluoride (fluoride application after laser irradiation) and fluoride-laser (fluoride was applied and then teeth were irradiated with laser). After surface treatment around brackets on enamel, the samples were stored in 0.1% thymol for less than 5 days and then they were exposed to a 10-day microbiological caries model. Microhardness values of enamel were evaluated with Vickers test. One sample of each group (5 teeth from 80 samples) was prepared for SEM (scanning electron microscopy) and the data from 75 remaining teeth were analyzed with analysis of variance (ANOVA) and chi-square tests (α =0.05). Results: Microhardness mean values from high to low were as follow: fluoride-laser, laser-fluoride, laser, fluoride and control. Microhardness in fluoride-laser group was significantly higher compared with that of the control group. Distribution adhesive remnant index (ARI) scores were significantly different between groups and most of bond failures occurred at the enamel-adhesive interface in groups 2 to 5 and at the adhesive-bracket interface in the control group. Conclusion: Combination of fluoride varnish and CO2 laser irradiation can reduce enamel demineralization around orthodontic brackets.

Fluoride in weathered rock aquifers of southern India: Managed Aquifer Recharge for mitigation.

PubMed

Brindha, K; Jagadeshan, G; Kalpana, L; Elango, L

2016-05-01

Climatic condition, geology, and geochemical processes in an area play a major role on groundwater quality. Impact of these on the fluoride content of groundwater was studied in three regions-part of Nalgonda district in Telangana, Pambar River basin, and Vaniyar River basin in Tamil Nadu, southern India, which experience semi-arid climate and are predominantly made of Precambrian rocks. High concentration of fluoride in groundwater above 4 mg/l was recorded. Human exposure dose for fluoride through groundwater was higher in Nalgonda than the other areas. With evaporation and rainfall being one of the major contributors for high fluoride apart from the weathering of fluoride rich minerals from rocks, the effect of increase in groundwater level on fluoride concentration was studied. This study reveals that groundwater in shallow environment of all three regions shows dilution effect due to rainfall recharge. Suitable managed aquifer recharge (MAR) methods can be adopted to dilute the fluoride rich groundwater in such regions which is explained with two case studies. However, in deep groundwater, increase in fluoride concentration with increase in groundwater level due to leaching of fluoride rich salts from the unsaturated zone was observed. Occurrence of fluoride above 1.5 mg/l was more in areas with deeper groundwater environment. Hence, practicing MAR in these regions will increase the fluoride content in groundwater and so physical or chemical treatment has to be adopted. This study brought out the fact that MAR cannot be practiced in all regions for dilution of ions in groundwater and that it is essential to analyze the fluctuation in groundwater level and the fluoride content before suggesting it as a suitable solution. Also, this study emphasizes that long-term monitoring of these factors is an important criterion for choosing the recharge areas.

TRANSURANIC ELEMENT, COMPOSITION THEREOF, AND METHODS FOR PRODUCING SEPARATING AND PURIFYING SAME

DOEpatents

Wahl, A.C.

1961-09-19

A process of separating plutonium from fission products contained in an aqueous solution is described. Plutonium, in the tri- or tetravalent state, and the fission products are coprecipitated on lanthanum fluoride, lanthanum oxalate, cerous fluoride, cerous phosphate, ceric iodate, zirconyl phosphate, thorium iodate, or thorium fluoride. The precipitate is dissolved in acid, and the plutonium is oxidized to the hexavalent state. The fission products are selectively precipitated on a carrier of the above group but different from that used for the coprecipitation. The plutonium in the solution, after removal of the fission product precipitate, is reduced to at least the tetravalent state and precipitated on lanthanum fluoride, lanthanum phosphate, lanthanum oxalate, lanthanum hydroxide, cerous fluoride, cerous phosphate, cerous oxalate, cerous hydroxide, ceric iodate, zirconyl phosphate, zirconyl iodate, zirconium hydroxide, thorium fluoride, thorium oxalate, thorium iodate, thorium peroxide, uranium iodate, uranium oxalate, or uranium peroxide, again using a different carrier than that used for the precipitation of the fission products.

Preparation of fly ash based zeolite for removal of fluoride from drinking water

NASA Astrophysics Data System (ADS)

Panda, Laxmidhar; Kar, Biswabandita; Dash, Subhakanta

2018-05-01

Fluoride contamination of drinking water is a worldwide phenomenon and scientists are working relentlessly to find ways to remove fluoride from drinking water. Out of the different methods employed for removal fluoride from drinking water adsorption process is the most suitable because in this process the adsorbent is regenerated and the process is cost effective. In the present study fly ash is used as the raw material, which is treated with alkali (NaOH) to form NaP1 zeolite. This zeolite is then subjected to characterization by standard procedures. It is found that the synthesized zeolite has more crystalline character than the raw fly ash and has also more voids and channels on its surface. The surface of the synthesized zeolite is modified with calcium chloride and the same is employed for removal of fluoride under varying pH, contact time, initial concentration of fluoride, temperature and adsorbent dose etc so as to assess the suitably or otherwise of the synthesized product.

Method for decontamination of nickel-fluoride-coated nickel containing actinide-metal fluorides

DOEpatents

Windt, N.F.; Williams, J.L.

In one aspect, the invention comprises contacting nickel-fluoride-coated nickel with gaseous ammonia at a temperature effecting nickel-catalyzed dissociation thereof and effecting hydrogen-reduction of the nickel fluoride. The resulting nickel is heated to form a melt and a slag and to effect transfer of actinide metals from the melt into the slag. The melt and slag are then separated. In another aspect, nickel contianing nickel oxide and actinide metals is contacted with ammonia at a temperature effecting nickel-catalyzed dissociation to effect conversion of the nickel oxide to the metal. The resulting nickel is then melted and separated as described. In another aspect nickel-fluoride-coated nickel containing actinide-metal fluorides is contacted with both steam and ammonia. The resulting nickel then is melted and separated as described. The invention is characterized by higher nickel recovery, efficient use of ammonia, a substantial decrease in slag formation and fuming, and a valuable increase in the service life of the furnace liners used for melting.

Comparative evaluation of the efficacy of fluoride varnish and casein phosphopeptide – Amorphous calcium phosphate in reducing Streptococcus mutans counts in dental plaque of children: An in vivo study

PubMed Central

Chandak, Shweta; Bhondey, Ashish; Bhardwaj, Amit; Pimpale, Jitesh; Chandwani, Manisha

2016-01-01

Aim: To assess the comparative efficacy of fluoride varnish and casein phosphopeptide–amorphous calcium phosphate (CPP–ACP) complex visa viz. Streptococcus mutans in plaque, and thereby the role that these two agents could play in the prevention of dental caries. Materials and Methods: A cluster sample of 120 caries inactive individuals belonging to moderate and high caries risk group were selected from 3–5-year-old age group based on the criteria given by Krassee and were randomized to four groups, namely, fluoride varnish – Group I, CPP–ACP complex – Group II, mixture of CPP–ACP complex –Gourp III, and fluoride and routine oral hygiene procedures as control – Group IV. The results thus obtained were analyzed using Statistical Package for the Social Sciences (SPSS) version 16. Results: A statistically significant difference in the pre and post-application scores of S. mutans (P < 0.01) count was observed in all the groups with CPP–ACP plus fluoride group being the most proficient. Conclusion: Materials such as fluoride varnish, CPP–ACP, and CPP–ACP plus fluoride protects the tooth structure, preserving the integrity of primary dentition, with the most encouraging results being with CPP–ACP plus fluoride. PMID:27891308

The concentration data of fluoride and health risk assessment in drinking water in the Ardakan city of Yazd province, Iran.

PubMed

Mirzabeygi Rad Fard, Majid; Yousefi, Mahmood; Soleimani, Hamed; Mohammadi, Ali Akbar; Mahvi, Amir Hossein; Abbasnia, Abbas

2018-06-01

According to the World Health Organization (WHO) reports, Iran is located in the global fluoride belts, so that is why carrying out extended research on this contaminant anion in water supplies must be considered. Due to the various industries in the Ardakan city, this region is severely suffering from fluoride contamination. This study was designed to investigate the fluoride concentration and its distribution pattern as well as related health risk assessment in groundwater resources of 28 villages of the Ardakan city in Yazd province using SPADNS method according to standard instructions. Our results show that, the average concentration of fluoride was 2.92 mg/l (range: 0.9-6 mg/l), also in half of the villages, the concentration range of this element was over than standard level (1.5 mg/l) given by WHO rules. In addition, risk assessment results showed that HQ value is higher than 1 in 46.4% of samples of groundwater resources in age groups of infants, children, teenagers and adults. Therefore, it is necessary to take measures to reduce fluoride concentration in drinking water in order to control resultant fluorosis. Actions should be implemented to enhance monitoring of fluoride levels to avoid the potential risk of high Fluoride concentration.

Trend Analysis of Studies on Water Fluoridation Related to Dental Caries in PubMed.

PubMed

Oh, Hyo-Jung; Choi, Hyeon-Mi; Kim, Chonghyuck; Jeon, Jae-Gyu

2018-04-04

Water fluoridation has been cited as one of the top 10 public health achievements of the 20th century. Herein, we analyzed water fluoridation articles related to dental caries published in PubMed between 1950 and 2016 using informetrics and linguistic methods to investigate trends in the studies. To this aim, queries such as "dental caries and (water fluoridation or fluoridated water)," "dental caries and (fluoride or fluoridation)," and "dental caries" were submitted to PubMed to retrieve information about articles on water fluoridation within the area of dental caries and fluoride - their titles, abstracts, publication dates, author affiliations, and publication journals. This article information was then collected by an automatic web crawler and examined through informetrics and linguistic analyses. It was found that the number of articles concerned with water fluoridation and dental caries was 3,381 and declined over time after 1970. The articles were published by 750 journals - most notably, Community Dentistry and Oral Epidemiology and Caries Research. With regard to the geographic distribution of the authors, Europe and North America, especially the USA and UK, accounted for 59.9% of the articles published during the years 1987 to 2015, though there was a sharp increase in the number of authors in Oceania and Asia in recent years. In the titles and abstracts of the articles, "community" and "fluorosis" were mentioned more frequently than the other key terms selected in this study, regardless of the period examined. Our findings may allow one to assess how the research on water fluoridation has evolved over the past several decades. © 2018 S. Karger AG, Basel.

Community-oriented administration of fluoride for the prevention of dental caries: a summary of the current situation in Asia.

PubMed

Petersen, P E; Baez, R J; Lennon, M A

2012-02-01

Dental caries is the most prevalent chronic disease affecting human populations around the world. It is recognized that fluoride plays a significant role in dental caries reduction. Meanwhile, several low- and middle-income countries of Asia have not yet implemented systematic fluoride programs; contributing factors relate to misconceptions about the mechanisms of fluoride, low priority given to oral health in national health policy and strategic plans, and lack of interest among public health administrators. A workshop on the effective use of fluoride in Asia took place in Phang-Nga, Thailand, in 2011. A series of country presentations addressed some of the topics mentioned above; in addition, speakers from countries of the region provided examples of successful fluoride interventions and discussed program limitations, barriers encountered, and solutions, as well as possibilities for expanding coverage. Participants acknowledged that automatic fluoridation through water, salt, and milk is the most effective and equitable strategy for the prevention of dental caries. Concerns were expressed that government-subsidized community fluoride prevention programs may face privatization. In addition, the use of affordable fluoride-containing toothpastes should be encouraged. The workshop identified: strengths and weaknesses of ongoing community-based fluoride programs, as well as the interest of countries in a particular method; the requirement for World Health Organization (WHO) technical assistance on various aspects, including fluoridation process, feasibility studies, and implementation of effective epidemiological surveillance of the program; exchange of information; and the need for inter-country collaboration. It was acknowledged that program process and evaluation at the local and country levels need further dissemination. The meeting was co-sponsored by the World Health Organization, the International Association for Dental Research, and the World Dental Federation.

Longitudinal evaluation of fluoride levels in nails of 18-30-month-old children that were using toothpastes with 500 and 1100 μg F/g.

PubMed

Amaral, Jackeline G; Freire, Isabelle R; Valle-Neto, Eduardo F R; Cunha, Robson F; Martinhon, Cleide C R; Delbem, Alberto C B

2014-10-01

This study aimed to evaluate the fluoride concentration in the fingernails and toenails of children aged 18-30 months during use of fluoride-containing toothpastes supplemented with calcium glycerophosphate (CaGP) or sodium trimetaphosphate (TMP). According to the toothpaste used, children (n = 56) were randomly assigned into three groups: 500 μg F/g with 1% TMP, 500 μg F/g with 0.25% CaGP, and 1100 μg F/g. Fingernails and toenails were collected monthly over a period of 330 days, from the beginning of toothpaste use. Fluoride concentration in the water consumed by the volunteers and fluoride intake from diet and toothpaste were also determined. Fluoride analyses were performed with the electrode after hexamethyldisiloxane-facilitated diffusion or by the direct method, according to the samples. Data passed normality and homoscedasticity tests and were analyzed by 2-way analysis of variance (anova) and 1-way anova followed by Student-Newman-Keuls test (P < 0.05). Fluoride levels in the fingernails and toenails as well as fluoride intake from toothpaste were similar for the groups treated with 500 μg F/g with 1% TMP and 500 μg F/g with 0.25% CaGP toothpastes, but significantly lower than the 1100 μg F/g group (P < 0.05). No significant differences were noted among the groups regarding fluoride intake from diet and that by water consumed by the volunteers (P > 0.05). The results of the longitudinal study suggest that the level of fluoride present in nails was lower with the use of toothpastes with a low fluoride concentration. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Comparative Analysis of Fluoride Concentrations in Groundwaters in Northern and Southern Ghana: Implications for the Contaminant Sources

NASA Astrophysics Data System (ADS)

Sunkari, Emmanuel Daanoba; Zango, Musah Saeed; Korboe, Harriet Mateko

2018-04-01

Bongo and Sekyere South districts, both in the northern and southern parts of Ghana, respectively, have high populations living in rural areas and most of them use groundwater for drinking purposes. The groundwater in these areas is prone to contamination from natural and/or artificial sources. Therefore this study aims; (1) to present a comparative analysis of the fluoride concentration in groundwater samples from Bongo and Sekyere South districts and the associated groundwater-rock interaction that may be the cause for the varied fluoride concentrations, (2) to determine the leaching potential of fluoride from the host rocks as the possible mechanism for groundwater contamination. Sixty (60) groundwater samples from active pumping wells and twelve (12) rock samples from outcrops were collected from various communities in the two districts for fluoride concentration and mineralogical analysis. Based on the variations in fluoride concentration, fluoride spatial distribution maps were prepared using empirical Bayesian kriging interpolation method and analysed by means of hierarchical cluster analysis. The fluoride concentration in Bongo district varies between 1.71 and 4.0 mg/L, whereas that in Sekyere South district changes from 0.3 to 0.8 mg/L. From the mineralogical studies, biotite has the highest percentage in the Bongo district and has positive correlation with fluoride concentration in the analysed water samples than in the Sekyere South district. The elevated fluoride concentration in the Bongo district relative to the Sekyere South district is due to the dissolution of biotite in the groundwater and the sufficient groundwater-rock interaction since the water samples are mainly sourced from deeper boreholes. This high fluoride concentration has resulted in a plethora of reported cases of dental fluorosis and other health-related issues in Bongo.

Comparative Analysis of Fluoride Concentrations in Groundwaters in Northern and Southern Ghana: Implications for the Contaminant Sources

NASA Astrophysics Data System (ADS)

Sunkari, Emmanuel Daanoba; Zango, Musah Saeed; Korboe, Harriet Mateko

2018-05-01

Bongo and Sekyere South districts, both in the northern and southern parts of Ghana, respectively, have high populations living in rural areas and most of them use groundwater for drinking purposes. The groundwater in these areas is prone to contamination from natural and/or artificial sources. Therefore this study aims; (1) to present a comparative analysis of the fluoride concentration in groundwater samples from Bongo and Sekyere South districts and the associated groundwater-rock interaction that may be the cause for the varied fluoride concentrations, (2) to determine the leaching potential of fluoride from the host rocks as the possible mechanism for groundwater contamination. Sixty (60) groundwater samples from active pumping wells and twelve (12) rock samples from outcrops were collected from various communities in the two districts for fluoride concentration and mineralogical analysis. Based on the variations in fluoride concentration, fluoride spatial distribution maps were prepared using empirical Bayesian kriging interpolation method and analysed by means of hierarchical cluster analysis. The fluoride concentration in Bongo district varies between 1.71 and 4.0 mg/L, whereas that in Sekyere South district changes from 0.3 to 0.8 mg/L. From the mineralogical studies, biotite has the highest percentage in the Bongo district and has positive correlation with fluoride concentration in the analysed water samples than in the Sekyere South district. The elevated fluoride concentration in the Bongo district relative to the Sekyere South district is due to the dissolution of biotite in the groundwater and the sufficient groundwater-rock interaction since the water samples are mainly sourced from deeper boreholes. This high fluoride concentration has resulted in a plethora of reported cases of dental fluorosis and other health-related issues in Bongo.

Investigation on the photophysical properties of ESPT inspired salicylaldehyde-based sensor for fluoride sensing.

PubMed

Liu, Kai; Zhao, Xiaojun; Liu, Qingxiang; Huo, Jianzhong; Wang, Xing; Wu, Yanping

2015-04-05

A simple, highly selective and sensitive chemosensor (E)-2-((quinolin-8-ylimino) methyl) phenol (QP) has been developed for the fluoride, as demonstrated by the photophysical properties obtained by UV-vis and fluorescent methods. Excited-state inter/intramolecular proton transfer (ESPT) was suggested to be responsible for the fluoride-induced 'turn on' fluorescence and the blue shift of 25 nm in the emission spectrum. Copyright © 2014 Elsevier B.V. All rights reserved.

Method for converting UF5 to UF4 in a molten fluoride salt

DOEpatents

Bennett, Melvin R.; Bamberger, Carlos E.; Kelmers, A. Donald

1977-01-01

The reduction of UF.sub.5 to UF.sub.4 in a molten fluoride salt by sparging with hydrogen is catalyzed by metallic platinum. The reaction is also catalyzed by platinum alloyed with gold reaction equipment.

Change of urinary fluoride and bone metabolism indicators in the endemic fluorosis areas of southern china after supplying low fluoride public water

PubMed Central

2013-01-01

Background Few studies have evaluated health impacts, especially biomarker changes, following implementation of a new environmental policy. This study examined changes in water fluoride, urinary fluoride (UF), and bone metabolism indicators in children after supplying low fluoride public water in endemic fluorosis areas of Southern China. We also assessed the relationship between UF and serum osteocalcin (BGP), calcitonin (CT), alkaline phosphatase (ALP), and bone mineral density to identify the most sensitive bone metabolism indicators related to fluoride exposure. Methods Four fluorosis-endemic villages (intervention villages) in Guangdong, China were randomly selected to receive low-fluoride water. One non-endemic fluorosis village with similar socio-economic status, living conditions, and health care access, was selected as the control group. 120 children aged 6-12 years old were randomly chosen from local schools in each village for the study. Water and urinary fluoride content as well as serum BGP, CT, ALP and bone mineral density were measured by the standard methods and compared between the children residing in the intervention villages and the control village. Benchmark dose (BMD) and benchmark dose lower limit (BMDL) were calculated for each bone damage indicator. Results Our study found that after water source change, fluoride concentrations in drinking water in all intervention villages (A-D) were significantly reduced to 0.11 mg/l, similar to that in the control village (E). Except for Village A where water change has only been taken place for 6 years, urinary fluoride concentrations in children of the intervention villages were lower or comparable to those in the control village after 10 years of supplying new public water. The values of almost all bone indicators in children living in Villages B-D and ALP in Village A were either lower or similar to those in the control village after the intervention. CT and BGP are sensitive bone metabolism indicators related to UF. While assessing the temporal trend of different abnormal bone indicators after the intervention, bone mineral density showed the most stable and the lowest abnormal rates over time. Conclusions Our results suggest that supplying low fluoride public water in Southern China is successful as measured by the reduction of fluoride in water and urine, and changes in various bone indicators to normal levels. A comparison of four bone indicators showed CT and BGP to be the most sensitive indicators. PMID:23425550

In vitro assessment of a toothpaste range specifically designed for children.

PubMed

Churchley, David; Schemehorn, Bruce R

2013-12-01

To evaluate the ability of a range of low abrasivity experimental toothpastes designed for use by children at different stages of their development (typically ages 0-2 years, 3-5 years and 6+ years) to promote fluoride uptake and remineralisation of artificial caries lesions. pH cycling study: demineralised human permanent enamel specimens were subjected to a daily pH cycling regime consisting of four 1-minute treatments with toothpaste slurries, a 4-hour acid challenge and remineralisation in pooled whole human saliva. Surface microhardness (SMH) was measured at baseline, 10 days and 20 days, and the fluoride content determined at 20 days. Enamel Fluoride Uptake (EFU): these studies were based on Method #40 described in the US Food and Drug Administration (FDA) testing procedures. Abrasivity: relative enamel abrasivity (REA) and relative dentine abrasivity (RDA) were measured using the Hefferren abrasivity test. Bioavailable fluoride: the bioavailable fluoride was determined for all experimental toothpastes from slurries of one part toothpaste plus 10 parts deionised water. Enamel remineralisation measured by changes in SMH correlated with enamel fluoride content. A statistically significant fluoride dose response was observed for all toothpastes tested across all age groups (P < 0.05). The fluoride content of specimens in the pH cycling model correlated with the EFU testing results. The enamel and dentine abrasivities were low and the level of bioavailable fluoride was high for all experimental toothpastes. A series of low abrasivity experimental toothpastes were developed which were effective at promoting fluoride uptake and remineralisation of artificial caries lesions. © 2013 FDI World Dental Federation.

Acoustic cavitation induced synthesis of zirconium impregnated activated carbon for effective fluoride scavenging from water by adsorption.

PubMed

Mullick, Aditi; Neogi, Sudarsan

2018-07-01

Environmental concern associated with the side effects of high fluoride content in ground water and surface water has prompted the researchers to look for an efficient, convenient and easy method. Considering the potential of a good adsorbent, present study reports the synthesis of a composite by impregnating zirconium on powdered activated carbon (AC) using ultrasound as the tool for synthesis and applying it for fluoride adsorption from water. The nature of the composite was determined through characterization by scanning electron microscopy (SEM), energy dispersive Xray (EDX), Xray diffraction (XRD), N 2 adsorption analysis (BET) and Fourier Transform Infrared Spectroscopy (FTIR) analysis. The pH pzc (point of zero charge) of the adsorbent was found to be 5.03; with the optimum pH obtained at 4 for adsorption of strong electronegative fluoride ions. The initial fluoride concentration was varied from 2.5 up to 20 mg.L -1 and the maximum adsorption capacity of 5 mg.g -1 was obtained. A maximum fluoride removal of 94.4% was obtained for an initial concentration of 2.5 mg.L -1 within an equilibrium time of 180 min. The adsorption isotherm followed the Langmuir isotherm model indicating a monolayer adsorption process and the adsorption kinetics followed pseudo second order model. The effects of various coexisting ions (HCO 3 - , NO 3 - , SO 4 2- , Cl - ) commonly present in the water were found to have negligible impact on the process performance. Conducting the adsorption-desorption studies for five consecutive cycles for an initial fluoride concentration of 10 mg.L -1 , the removal efficiency reduced from 86.2 to 32.6%. The ultrasonic method provided an easy route to synthesize the composite in less time and significantly reduced energy consumption by more than 96% compared to the conventional method. Copyright © 2018 Elsevier B.V. All rights reserved.

Determination of small quantities of fluoride in water: A modified zirconium-alizarin method

USGS Publications Warehouse

Lamar, W.L.; Seegmiller, C.G.

1941-01-01

The zirconium-alizarin method has been modified to facilitate the convenient and accurate determination of small amounts of fluoride in a large number of water samples. Sulfuric acid is used to acidify the samples to reduce the interference of sulfate. The pH is accurately controlled to give the most sensitive comparisons. Most natural waters can be analyzed by the modified procedure without resorting to correction curves. The fluoride content of waters containing less than 500 parts per million of sulfate, 500 parts per million of bicarbonate, and 1000 parts per million of chloride may be determined within a limit of about 0.1 part per million when a 100-ml. sample is used.

Curcumin based optical sensing of fluoride in organo-aqueous media using irradiation technique

NASA Astrophysics Data System (ADS)

Venkataraj, Roopa; Radhakrishnan, P.; Kailasnath, M.

2017-06-01

The present work describes the degradation of natural dye Curcumin in organic-aqueous media upon irradiation by a multi-wavelength source of light like mercury lamp. The presence of anions in the solution leads to degradation of Curcumin and this degradation is especially enhanced in the case of fluoride ion. The degradation of Curcumin is investigated by studying the change in its absorption and fluorescence characteristics in organoaqueous solution upon irradiation. A broad detection range of fluoride ranging from 2.3×10-6-2.22×10-3 M points to the potential of the method of visible light irradiation enabling aqueous based sensing of fluoride using Curcumin.

Short term serum pharmacokinetics of diammine silver fluoride after oral application.

PubMed

Vasquez, Elsa; Zegarra, Graciela; Chirinos, Edgar; Castillo, Jorge L; Taves, Donald R; Watson, Gene E; Dills, Russell; Mancl, Lloyd L; Milgrom, Peter

2012-12-31

There is growing interest in the use of diammine silver fluoride (DSF) as a topical agent to treat dentin hypersensitivity and dental caries as gauged by increasing published research from many parts of the world. While DSF has been available in various formulations for many years, most of its pharmacokinetic aspects within the therapeutic concentration range have never been fully characterized. This preliminary study determined the applied doses (3 teeth treated), maximum serum concentrations, and time to maximum serum concentration for fluoride and silver in 6 adults over 4 h. Fluoride was determined using the indirect diffusion method with a fluoride selective electrode, and silver was determined using inductively coupled plasma-mass spectrometry. The mean amount of DSF solution applied to the 3 teeth was 7.57 mg (6.04 μL). Over the 4 hour observation period, the mean maximum serum concentrations were 1.86 μmol/L for fluoride and 206 nmol/L for silver. These maximums were reached 3.0 h and 2.5 h for fluoride and silver, respectively. Fluoride exposure was below the U.S. Environmental Protection Agency (EPA) oral reference dose. Silver exposure exceeded the EPA oral reference dose for cumulative daily exposure over a lifetime, but for occasional use was well below concentrations associated with toxicity. This preliminary study suggests that serum concentrations of fluoride and silver after topical application of DSF should pose little toxicity risk when used in adults. NCT01664871.

Estimation of fluoride concentration in drinking water and common beverages in United Arab Emirates (UAE).

PubMed

Walia, Tarun; Abu Fanas, Salem; Akbar, Madiha; Eddin, Jamal; Adnan, Mohamad

2017-07-01

To assess fluoride concentration in drinking water which include tap water of 4 emirates - Abu Dhabi, Dubai, Sharjah and Ajman plus bottled water, commonly available soft drinks & juices in United Arab Emirates. Five different samples of tap water collected from each of the four emirates of UAE: Ajman, Sharjah, Abu Dhabi and Dubai; twenty-two brands of bottled water and fifteen brands of popular cold beverages, purchased from different supermarkets in U.A.E were tested using ion selective electrode method and the fluoride concentration was determined. The mean fluoride content of tap water samples was 0.14 mg F/L with a range of 0.04-0.3 mg F/L; with Ajman tap water samples showing the highest mean fluoride content of 0.3 mg F/L. The mean fluoride content for both bottled drinking water and beverages was 0.07 mg F/L with a range of 0.02-0.50 mg F/L and 0.04-0.1 mg F/L respectively. Majority (68.2%) of the bottled water are produced locally within U.A.E while a few (31.8%) are imported. The tap water, bottled water and beverages available in U.A.E show varying concentrations of fluoride, however none showed the optimal level necessary to prevent dental caries. Dental professionals in U.A.E should be aware of the fluoride concentrations before prescribing fluoride supplements to children.

[Exposure to fluorides from drinking water in the city of Aguascalientes, Mexico].

PubMed

Trejo-Vázquez, R; Bonilla-Petriciolet, A

2001-08-01

Determine the fluoride content in all the wells that supply drinking water to the city of Aguascalientes, Mexico, in order to establish the population's degree of exposure. The fluoride content of the 126 wells that supply drinking water to the city of Aguascalientes was determined, using the SPADNS method, in accordance with two Mexican regulations, NMX-AA-77-1982 and NMX-014-SSAI-1993. Using that data, we created fluoride isopleth maps showing the distribution of fluoride concentrations in the water supplies for the city of Aguascalientes. We also estimated exposure doses for the city's inhabitants. The mean analysis uncertainty was 3.9%. Seventy-three wells had a fluoride concentration of" 1.5 mg/L, which was the maximum permissible value set by the Mexican standards then in effect. All the maximum exposure doses surpassed the minimum risk level set by Agency for Toxic Substances and Disease Registry (ATSDR) of the Department of Health and Human Services of the United States of America. In the children under 1 year of age, even the minimum does was slightly higher than the ATSDR risk level. From estimating the fluoride exposure doses caused by water consumption in the city of Aguascalientes and comparing those doses with ones from other states in Mexico, we concluded that the fluoride intake in Aguascalientes represents a potential risk for inhabitants' health. The fluoride content of the city's drinking water should be reduced to 0.69 mg/L.

METHOD OF IMPROVING THE CARRIER PRECIPITATION OF PLUTONIUM

DOEpatents

Kamack, H.J.; Balthis, J.H.

1958-12-01

Plutonium values can be recovered from acidic solutlons by adding lead nitrate, hydrogen fluoride, lantha num nitrate, and sulfurlc acid to the solution to form a carrler preclpitate. The lead sulfate formed improves the separatlon characteristics of the lanthanum fluoride carrier precipitate,

ELECTROLYTIC PRODUCTION OF URANIUM TETRAFLUORIDE

DOEpatents

Lofthouse, E.

1954-08-31

This patent relates to electrolytic methods for the production of uranium tetrafluoride. According to the present invention a process for the production of uranium tetrafluoride comprises submitting to electrolysis an aqueous solution of uranyl fluoride containing free hydrofluoric acid. Advantageously the aqueous solution of uranyl fluoride is obtained by dissolving uranium hexafluoride in water. On electrolysis, the uranyl ions are reduced to uranous tons at the cathode and immediately combine with the fluoride ions in solution to form the insoluble uranium tetrafluoride which is precipitated.

Novel heterocyclic thiosemicarbazones derivatives as colorimetric and "turn on" fluorescent sensors for fluoride anion sensing employing hydrogen bonding.

PubMed

Ashok Kumar, S L; Saravana Kumar, M; Sreeja, P B; Sreekanth, A

2013-09-01

Two novel heterocyclic thiosemicarbazone derivatives have been synthesized, and characterized, by means of spectroscopic and single crystal X-ray diffraction methods. Their chromophoric-fluorogenic response towards anions in competing solvent dimethyl sulfoxide (DMSO) was studied. The receptor shows selective recognition towards fluoride anion. The binding affinity of the receptors with fluoride anion was calculated using UV-visible and fluorescence spectroscopic techniques. Copyright © 2013 Elsevier B.V. All rights reserved.

Synthesis and performance evaluation of Al/Fe oxide coated diatomaceous earth in groundwater defluoridation: Towards fluorosis mitigation.

PubMed

Izuagie, Anthony A; Gitari, Wilson M; Gumbo, Jabulani R

2016-08-23

The quest to reduce fluoride in groundwater to WHO acceptable limit of 1.5 mg/L to prevent diseases such as teeth mottling and skeletal fluorosis was the motivation for this study. Al/Fe oxide-modified diatomaceous earth was prepared and its defluoridation potential evaluated by batch method. The sorbent with pHpzc 6.0 ± 0.2 is very reactive. The maximum 82.3% fluoride removal attained in 50 min using a dosage of 0.3 g/100 mL in 10 mg/L fluoride was almost attained within 5 min contact time; 81.3% being the percent fluoride removal at 5 min contact time. The sorbent has a usage advantage of not requiring solution pH adjustment before it can exhibit its fluoride removal potential. A substantial amount of fluoride (93.1%) was removed from solution when a sorbent dosage of 0.6 g/100 mL was contacted with 10 mg/L fluoride solution for 50 min at a mixing rate of 200 rpm. The optimum adsorption capacity of the adsorbent was 7.633 mg/g using a solution containing initially 100 mg/L fluoride. The equilibrium pH of the suspensions ranged between 6.77 and 8.26 for 10 and 100 mg/L fluoride solutions respectively. Contacting the sorbent at a dosage of 0.6 g/100 mL with field water containing 5.53 mg/L at 200 rpm for 50 min reduced the fluoride content to 0.928 mg/L-a value below the upper limit of WHO guideline of 1.5 mg/L fluoride in drinking water. The sorption data fitted to both Langmuir and Freundlich isotherms but better with the former. The sorption data obeyed only the pseudo-second-order kinetic, which implies that fluoride was chemisorbed.

Evaluation of Fluoride Retention Due to Most Commonly Consumed Estuarine Fishes Among Fish Consuming Population of Andhra Pradesh as a Contributing Factor to Dental Fluorosis: A Cross-Sectional Study.

PubMed

Ganta, Shravani; Yousuf, Asif; Nagaraj, Anup; Pareek, Sonia; Sidiq, Mohsin; Singh, Kushpal; Vishnani, Preeti

2015-06-01

Fluoride in drinking water is known for both beneficial and detrimental effects on health. The principal sources of fluoride include water, some species of vegetation, certain edible marine animals, dust and industrial processes. The purpose of this study was to evaluate the fluoride retention of most commonly consumed estuarine fishes among fish consuming population of Andhra Pradesh. A cross-sectional study was conducted to evaluate the amount of fluoride retention due to ten most commonly consumed estuarine fishes as a contributing factor to Fluorosis by SPADNS Spectrophotometric method. The presence and severity of dental fluorosis among fish consuming population was recorded using Community Fluorosis Index. Statistical analysis was done using MedCalc v12.2.1.0 software. For Sea water fishes, the fluoride levels in bone were maximum in Indian Sardine (4.22 ppm). Amongst the river water fishes, the fluoride levels in bone were maximum in Catla (1.51 ppm). Also, the mean total fluoride concentrations of all the river fishes in skin, muscle and bone were less (0.86 ppm) as compared to the sea water fishes (2.59 ppm). It was unveiled that sea fishes accumulate relatively large amounts of Fluoride as compared to the river water fishes. The mean Community Fluorosis Index was found to be 1.06 amongst a sampled fish consuming population. Evaluation by Community Index for Dental fluorosis (CFI) suggested that fluorosis is of medium public health importance. It was analysed that bone tends to accumulate more amount of fluoride followed by muscle and skin which might be due to the increased permeability and chemical trapping of fluoride inside the tissues. The amount of fluoride present in the fishes is directly related to the severity of fluorosis amongst fish consuming population, suggesting fishes as a contributing factor to fluorosis depending upon the dietary consumption.

[Fluoride in drinking water in Cuba and its association with geological and geographical variables].

PubMed

Luna, Liliam Cuéllar; Melián, Maricel García

2003-11-01

To determine the association between different concentrations of the fluoride ion in drinking water and some geological and geographical variables in Cuba, by using a geographic information system. From November 1998 to October 1999 we studied the fluoride concentration in the sources of drinking water for 753 Cuban localities that had at least 1 000 inhabitants. For the information analysis we utilized the MapInfo Professional version 5.5 geographic information system, using the overlaying method. The study variables were the concentration of the fluoride ion in the water sources, the geological characteristics of the area, the alignments (geological characteristics that were found together), the types of water sources, and whether an area was a plain or mountainous. The results were grouped by locality and municipality. In 83.1% of the localities, the water samples were collected from wells and springs, and the remaining 16.9% came from dams and rivers. Of the 753 localities studied, 675 of them (89.6%) had low or medium fluoride concentrations (under 0.7 mg/L). The eastern region of the country was the one most affected by high fluoride concentrations in the waters, followed by the central region of the country. The majority of the localities with high natural fluoride concentrations were in areas located on Cretaceous volcanic arc rocks. The presence of fluoride in the drinking waters was related to the alignments with the earth's crust, in rock complexes of volcanic-sedimentary origin and of intrusive origin and also in carbonate rocks. However, the highest fluoride concentrations generally coincided with rock complexes of volcanic-sedimentary origin and of intrusive origin. All the localities with high fluoride concentrations in the water were associated with wells. The fluoride concentration is low or medium in the drinking water sources for 89.6% of the Cuban localities with at least 1 000 inhabitants. Geological and geographical characteristics can help identify areas with optimal or high concentrations of the fluoride ion in the drinking water.

High-temperature corrosion of metals in the salt and metallic melts containing rare earths

NASA Astrophysics Data System (ADS)

Karpov, V. V.; Abramov, A. V.; Zhilyakov, A. Yu.; Belikov, S. V.; Volkovich, V. A.; Polovov, I. B.; Rebrin, O. I.

2016-09-01

A complex of independent methods was employed to study the corrosion resistance of molybdenum, zirconium, tantalum and tungsten in chloride, chloride-fluoride and fluoride-oxide melts based on LiCl, CaCl2, NaCl- KCl, LiF, and containing rare earths. Tests were conducted for 30 h at 750-1050 °C. The metals showed excellent corrosion resistance in fused chlorides (the corrosion rates were below 0.0005 g/(m2 h). Despite the presence of chemically active fluoride ions in the chloride-fluoride melts, the metals studied also showed very low corrosion rates, except molybdenum, for which the rate of corrosion was 0,8 g/(m2 h). The corrosion resistance of tantalum was considerably reduced in the fluoride-oxide melts; the corrosion rate was over 1 g/(m2 h) corresponding to the 8-th grade of stability and placing tantalum to the group of "low stability" materials.

Data on fluoride concentration levels in cold and warm season in City area of Sistan and Baluchistan Province, Iran.

PubMed

Neisi, Akazem; Mirzabeygi Radfard, Majid; Zeyduni, Ghader; Hamzezadeh, Asghar; Jalili, Davoud; Abbasnia, Abbas; Yousefi, Mahmood; Khodadadi, Rouhollah

2018-06-01

The need for fluoride in drinking water to the extent that reduces the amount of tooth decay and the other hand does not cause dental fluorosis, has been well documented as an important fact. The aim of this research is to survey values of fluoride in drinking water in Sistan and Baluchestan. In this descriptive and analytical study, the number of 551 samples during 4 seasons of 2013 year from rural drinking water sources via rural water and Wastewater Company has been taken. The concentration of fluoride in water samples was measured using SPADNS method. Results shows that the average concentration of fluoride in drinking water supplies for the rural region of Khash, Sarbaz, Iranshahr, Saravan, Nickshahr city are 0.72 (±0.31), 0.55(±0.21), 0.33 (±0.127), 0.6 (±0.24), 0.435 (±0.23) respectively.

Fluoride concentration level in rural area in Poldasht city and daily fluoride intake based on drinking water consumption with temperature.

PubMed

Mohammadi, Ali Akbar; Yousefi, Mahmood; Mahvi, Amir Hossein

2017-08-01

Long-term exposure to high level of fluoride can caused several adverse effects on human health including dental and skeletal fluorosis. We investigated all the drinking water source located in rural areas of Poldasht city, west Azerbaijan Province, North West Iran between 2014 and 2015. Fluoride concentration of water samples was measured by SPADNS method. We found that in the villages of Poldasht the average of fluoride concentration in drinking water sources (well, and the river) was in the range mg/l 0.28-10.23. The average daily received per 2 l of drinking water is in the range mg/l 0.7-16.6 per day per person. Drinking water demands cause fluorosis in the villages around the area residents and based on the findings of this study writers are announced suggestions below in order to take care of the health of area residents.

A novel UV-photolysis approach with acetone and isopropyl alcohol for the rapid determination of fluoride in organofluorine-containing drugs by spectrophotometry.

PubMed

Mullapudi, Venkata Balarama Krishna; Dheram, Karunasagar

2018-01-01

A UV photolysis decomposition (UVPD) method for the determination of fluoride in fluorine containing pharmaceuticals by spectrophotometry is reported. It is based on the use of high intensity UV-irradiation in the presence of a digesting solution comprising a mixture of acetone and isopropanol. For the optimization of the UVPD procedure, three bulk drugs (levofloxacin, nebivolol and efavirenz) were chosen as representatives of three diverse compounds containing a single fluorine atom, two fluorine atoms, and trifluoromethyl groups respectively. Operational conditions of the UVPD method, such as concentration and volume of reagents (acetone and isopropyl alcohol), and UV irradiation time (1-6 minutes) were optimized. The efficiency of digestion was evaluated by the determination of fluoride in sample digests. Using the developed method, it was possible for complete conversion of the organofluoride to free fluoride ion for its subsequent determination by spectrophotometry based on bleaching of Zr-xylenol orange-color complex. Quantitative recovery (>98%) of the fluorine in the drug samples could be achieved using a mixture of 2% acetone + 2% isopropyl alcohol + 0.003% Na 2 CO 3 in just 5 minutes of UV irradiation, which can be considered an important aspect considering the difficulties involved in the cleavage of the CF bond. Accuracy was evaluated by comparison of results obtained by the UVPD method with the values estimated using formula weight of the compound and no statistical difference was observed between the results. Therefore, the proposed method is suitable for application in routine analysis of fluoride in organofluorine-containing drugs. Copyright © 2016. Published by Elsevier B.V.

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

40 CFR 60.201 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-Process Phosphoric Acid Plants § 60.201 Definitions. As used in this subpart, all terms not defined herein... acid plant means any facility manufacturing phosphoric acid by reacting phosphate rock and acid. (b) Total fluorides means elemental fluorine and all fluoride compounds as measured by reference methods...

MRI brain in monohalomethane toxic encephalopathy: A case report.

PubMed

Deshmukh, Yogeshwari S; Atre, Ashish; Shah, Darshan; Kothari, Sudhir

2013-07-01

Monohalomethanes are alkylating agents that have been used as methylating agents, laboratory reagents, refrigerants, aerosol propellants, pesticides, fumigants, fire-extinguishing agents, anesthetics, degreasers, blowing agents for plastic foams, and chemical intermediates. Compounds in this group are methyl chloride, methyl bromide, methyl iodide (MI), and methyl fluoride. MI is a colorless volatile liquid used as a methylating agent to manufacture a few pharmaceuticals and is also used as a fumigative insecticide. It is a rare intoxicant. Neurotoxicity is known with both acute and chronic exposure to MI. We present the characteristic magnetic resonance imaging (MRI) brain findings in a patient who developed neuropsychiatric symptoms weeks after occupational exposure to excessive doses of MI.

An update of the federal drinking water regs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pontius, F.W.

1995-02-01

Previous reviews have summarized the regulations promulgated for volatile organic chemicals (VOCs), fluoride, surface water treatment, total coliform bacteria, lead and copper, and Phase 2 and Phase 5 synthetic organic contaminants (SOCs) and inorganic contaminants (IOCs). Current developments related to these rules and anticipated new rules are reviewed in this article. Current numerical drinking water standards and best available technology (BAT) are summarized. The status of all current, proposed, and anticipated regulations is also summarized. Dates for anticipated agency actions are based on the US Environmental Protection Agency's (USEPA's) published regulatory agenda and on information released by the agency throughmore » December 1994; these dates can change as the agency reconsiders its regulatory policies.« less

Effect of fluoride on the cell viability, cell organelle potential, and photosynthetic capacity of freshwater and soil algae.

PubMed

Chae, Yooeun; Kim, Dokyung; An, Youn-Joo

2016-12-01

Although fluoride occurs naturally in the environment, excessive amounts of fluoride in freshwater and terrestrial ecosystems can be harmful. We evaluated the toxicity of fluoride compounds on the growth, viability, and photosynthetic capacity of freshwater (Chlamydomonas reinhardtii and Pseudokirchneriella subcapitata) and terrestrial (Chlorococcum infusionum) algae. To measure algal growth inhibition, a flow cytometric method was adopted (i.e., cell size, granularity, and auto-fluorescence measurements), and algal yield was calculated to assess cell viability. Rhodamine123 and fluorescein diacetate were used to evaluate mitochondrial membrane potential (MMA, ΔΨ m ) and cell permeability. Nine parameters related to the photosynthetic capacity of algae were also evaluated. The results indicated that high concentrations of fluoride compounds affected cell viability, cell organelle potential, and photosynthetic functions. The cell viability measurements of the three algal species decreased, but apoptosis was only observed in C. infusionum. The MMA (ΔΨ m ) of cells exposed to fluoride varied among species, and the cell permeability of the three species generally decreased. The decrease in the photosynthetic activity of algae may be attributable to the combination of fluoride ions (F - ) with magnesium ions (Mg 2+ ) in chlorophyll. Our results therefore provide strong evidence for the potential risks of fluoride compounds to microflora and microfauna in freshwater and terrestrial ecosystems. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fluoride contamination in drinking water in rural habitations of Central Rajasthan, India.

PubMed

Hussain, Ikbal; Arif, Mohd; Hussain, Jakir

2012-08-01

Fluoride concentration in groundwater sources used as major drinking water source in rural area of block Nawa (Nagaur District), Rajasthan was examined and the toxic effects by intake of excess fluoride on rural habitants were studied. In block 13, habitations (30%) were found to have fluoride concentration more than 1.5 mg/l (viz. maximum desirable limit of Indian drinking water standards IS 10500, 1999). In five habitations (11%), fluoride concentration in groundwater is at toxic level (viz. above 3.0 mg/l). The maximum fluoride concentration in the block is 5.91 mg/l from Sirsi village. As per the desirable and maximum permissible limit for fluoride in drinking water, determined by World Health Organization or by Bureau of Indian Standards, the groundwater of about 13 habitations of the studied sites is unfit for drinking purposes. Due to the higher fluoride level in drinking water, several cases of dental and skeletal fluorosis have appeared at alarming rate in this region. There is an instant need to take ameliorative steps in this region to prevent the population from fluorosis. Groundwater sources of block Nawa can be used for drinking after an effective treatment in absence of other safe source. The evaluation of various defluoridation methods on the basis of social and economical structure of India reveals that the clay pot chip, activated alumina adsorption, and Nalgonda techniques are the most promising.

Prevention and Treatment of White Spot Lesions in Orthodontic Patients.

PubMed

Khoroushi, Maryam; Kachuie, Marzie

2017-01-01

Decalcification of enamel, appearing as white spot lesions (WSLs), around fixed orthodontic appliances is a major challenge during and after fixed orthodontic treatment by considering the fact that the goal of orthodontic treatment is to enhance facial and dental esthetic appearance. Banded or bonded teeth exhibit a significantly higher rate of WSLs compared to the controls with no braces as fixed appliances and the bonding materials promote retention of biofilms. These lesions are managed in the first step by establishing good oral hygiene habits and prophylaxis with topical fluorides, including high-fluoride toothpastes, fluoride mouthwashes, gels, varnishes, fluoride-containing bonding materials, and elastic ligatures. Recently, other materials and methods have been recommended, including the application of casein phosphopeptides-amorphous calcium phosphate, antiseptics, probiotics, polyols, sealants, laser, tooth bleaching agents, resin infiltration, and microabrasion. This article reviews the currently used methods to manage enamel demineralization during and after orthodontic treatment and the risk factors and preventive measures based on the latest evidence.

Prevention and Treatment of White Spot Lesions in Orthodontic Patients

PubMed Central

Khoroushi, Maryam; Kachuie, Marzie

2017-01-01

Decalcification of enamel, appearing as white spot lesions (WSLs), around fixed orthodontic appliances is a major challenge during and after fixed orthodontic treatment by considering the fact that the goal of orthodontic treatment is to enhance facial and dental esthetic appearance. Banded or bonded teeth exhibit a significantly higher rate of WSLs compared to the controls with no braces as fixed appliances and the bonding materials promote retention of biofilms. These lesions are managed in the first step by establishing good oral hygiene habits and prophylaxis with topical fluorides, including high-fluoride toothpastes, fluoride mouthwashes, gels, varnishes, fluoride-containing bonding materials, and elastic ligatures. Recently, other materials and methods have been recommended, including the application of casein phosphopeptides-amorphous calcium phosphate, antiseptics, probiotics, polyols, sealants, laser, tooth bleaching agents, resin infiltration, and microabrasion. This article reviews the currently used methods to manage enamel demineralization during and after orthodontic treatment and the risk factors and preventive measures based on the latest evidence. PMID:28566845

Dug Well Recharge Method for Insitu Mitigation of Fluoride Contamination in Groundwater

NASA Astrophysics Data System (ADS)

Ganesan, G.; Lakshmanan, E.; Gunalan, J.

2016-12-01

Groundwater with fluoride concentration exceeding 1.5 mg/l is not suitable for drinking water supply as it may cause health issues such as dental and skeletal fluorosis to humans. Several million people around the world has been affected by fluorosis. The objective of the study is to mitigate the problem of fluoride contamination in groundwater by increasing groundwater recharge through a dug well recharge system. The study was carried out in a part of Vaniyar river basin, northwest Tamil Nadu, India where fluorosis is prevalent. A cylindrical pit of 1m diameter and 1.5 m height was constructed during May 2014 at a distance of about 4 m from a dug well existing in this area. This cylindrical pit was divided into 3 compartments and one of them was filled with gravel and one with sand. The third compartment was kept empty for inspection and maintenance. The rainfall collected in a funnel shaped depression was allowed to pass through these compartments to discharge in the nearby dug well through a pipe. The concentration of the fluoride in groundwater from this well was had been monitoring on bi-monthly basis from the year 2012 to 2014. After construction of dug well recharge system, the groundwater level has raised by about 5 m and the fluoride concentration has decreased from 3.1 mg/l to 1.44 mg/l due to recharge. The concentration of fluoride and groundwater level is being monitored on daily basis from June 2014. It is evident that the recharge system constructed is working well and the concentration of fluoride in groundwater is within the permissible limit. The advantage of this dug well recharge system is its low cost and the ease of implementation. Thus this pilot study on dug well recharge system demonstrated it's potential in reducing the concentration of fluoride in groundwater which is more beneficial to the society as they cannot afford the well proven water treatment methods.

In Vitro Comparison Of Fluoride Gel Alone and in Combination With Er,Cr:YSGG Laser on Reducing White Spot Lesions in Primary Teeth.

PubMed

Molaasadollah, Fatemeh; Asnaashari, Mohammad; Mashhadi Abbas, Fatemeh; Jafary, Maral

2017-01-01

Introduction: Laser therapy has been suggested as a method for caries-prevention, and ErCr:YSGG laser is increasingly used in dentistry. This study aimed to compare the efficacy of fluoride gel alone and in conjunction with Er,Cr:YSGG laser for remineralization of white spot lesions (WSLs) in primary teeth. Methods: This study was conducted on 20 primary teeth with WSLs extracted for orthodontic reasons. Three sections were made of each tooth at the site of WSLs. The surface area of WSLs was measured under a stereomicroscope at ×25 magnification. Samples were assigned to 3 groups of control (group 1), exposure to 1.23% APF gel for 4 minutes (group 2) and Er,Cr:YSGG laser (0.5 W power, 20 Hz frequency, 60% water, 40% air, pulse duration of 5±1 seconds) plus fluoride (group 3). All samples were stored in artificial saliva for 10 days and then the surface area of the WSLs was measured again under a stereomicroscope. Data were analyzed using the Kruskal-Wallis, MannWhitney and Wilcoxon signed rank tests. Results: The reduction in surface area of the WSLs was significantly different between the control and fluoride ( P <0.001) and also the control and laser plus fluoride groups ( P <0.001); the difference between fluoride and laser plus fluoride groups was not significant ( P =0.265). Comparison of the surface area of WSLs before and after the intervention showed no significant difference in group one ( P =0.737) while this difference in groups 2 ( P <0.001) and 3 ( P <0.001) was statistically significant. Conclusion: The results showed that Er,Cr:YSGG laser irradiation plus 1.23% APF gel was not significantly different from the application of fluoride gel alone in enhancing the remineralization of WSLs.

pH-cycling models for in vitro evaluation of the efficacy of fluoridated dentifrices for caries control: strengths and limitations

PubMed Central

BUZALAF, Marília Afonso Rabelo; HANNAS, Angélica Reis; MAGALHÃES, Ana Carolina; RIOS, Daniela; HONÓRIO, Heitor Marques; DELBEM, Alberto Carlos Botazzo

2010-01-01

Despite a plethora of in situ studies and clinical trials evaluating the efficacy of fluoridated dentifrices on caries control, in vitro pH cycling models are still broadly used because they mimic the dynamics of mineral loss and gain involved in caries formation. This paper critically reviews the current literature on existing pH-cycling models for the in vitro evaluation of the efficacy of fluoridated dentifrices for caries control, focusing on their strengths and limitations. A search was undertaken in the MEDLINE electronic journal database using the keywords "pH-cycling", "demineralization", "remineralization", "in vitro", "fluoride", "dentifrice". The primary outcome was the decrease of demineralization or the increase of remineralization as measured by different methods (e.g.: transverse microradiography) or tooth fluoride uptake. Inclusion of studies, data extraction and quality assessment were undertaken independently and in duplicate by two members of the review team. Disagreements were solved by discussion and consensus or by a third party. One hundred and sixteen studies were included, of which 42 addressed specifically the comparison of dentifrices using different pH-cycling models. The other studies included meta-analysis or reviews, data about the effect of different fluoride sources on de-remineralization, different methods for analysis de-remineralization and chemical variables and characteristics of dental hard tissues that might have influence on de-remineralization processes. Generally, the studies presented ability to detect known results established by clinical trials, to demonstrate dose-related responses in the fluoride content of the dentifrices, and to provide repeatability and reproducibility between tests. In order to accomplish these features satisfactorily, it is mandatory to take into account the type of substrate and baseline artificial lesion, as well as the adequate response variables and statistical approaches to be used. This critical review of literature showed that the currently available pH-cycling models are appropriate to detect dose-response and pH-response of fluoride dentifrices, and to evaluate the impact of new active principles on the effect of fluoridated dentifrices, as well as their association with other anti-caries treatments. PMID:20835565

Cost-effectiveness models for dental caries prevention programmes among Chilean schoolchildren.

PubMed

Mariño, R; Fajardo, J; Morgan, M

2012-12-01

This study aims to estimate the cost-effectiveness from a societal perspective of seven dental caries prevention programmes among schoolchildren in Chile: three community-based programmes: water-fluoridation, salt-fluoridation and dental sealants; and four school-based programmes: milk-fluoridation; fluoridated mouthrinses (FMR); APF-Gel, and supervised toothbrushing with fluoride toothpaste. Standard cost-effectiveness analysis methods were used. The costs associated with implementing and operating each programme, using a societal perspective, were identified and estimated. The comparator was non-intervention. Health outcomes were measured as dental caries averted over a 6-year period. Costs were estimated as direct treatment costs, programmes costs and costs of productivity losses as a result of each dental caries prevention programme. Incremental cost-effectiveness ratios were calculated for each programme. Sensitivity analyses were conducted over key parameters. Primary cost-effectiveness analysis (discounted) indicated that four programmes showed net social savings by the DMFT averted. These savings encompassed a range of values per diseased tooth averted; US$16.21 (salt-fluoridation), US$14.89 (community water fluoridation); US$14.78 (milk fluoridation); and US$8.63 (FMR). Individual programmes using an APF-Gel application, dental sealants, and supervised tooth brushing using fluoridated toothpaste, represent costs for the society per diseased tooth averted of US$21.30, US$11.56 and US$8.55, respectively. Based on cost required to prevent one carious tooth among schoolchildren, salt fluoridation was the most cost-effective, with APF-Gel ranking as least cost-effective. Findings confirm that most community/school-based dental caries interventions are cost-effective uses of society's financial resources. The models used are conservative and likely to underestimate the real benefits of each intervention.

In Vitro Comparison of the Effects of Diode Laser and CO2 Laser on Topical Fluoride Uptake in Primary Teeth

PubMed Central

Bahrololoomi, Zahra; Sorouri, Milad

2015-01-01

Objectives: Fluoride therapy is important for control and prevention of dental caries. Laser irradiation can increase fluoride uptake especially when combined with topical fluoride application. The objective of this study was to compare the effects of CO2 and diode lasers on enamel fluoride uptake in primary teeth. Materials and Methods: Forty human primary molars were randomly assigned to four groups (n=10). The roots were removed and the crowns were sectioned mesiodistally into buccal and lingual halves as the experimental and control groups. All samples were treated with 5% sodium fluoride (NaF) varnish. The experimental samples in the four groups were irradiated with 5 or 7W diode or 1 or 2W CO2 laser for 15 seconds and were compared with the controls in terms of fluoride uptake, which was determined using an ion selective electrode after acid dissolution of the specimens. Data were analyzed by SPSS version 16 using ANOVA treating the control measurements as covariates. Results: The estimated amount of fluoride uptake was 59.5± 16.31 ppm, 66.5± 14.9 ppm, 78.6± 12.43 ppm and 90.4± 11.51 ppm for 5W and 7 W diode and 1W and 2 W CO2 lasers, respectively, which were significantly greater than the values in the conventional topical fluoridation group (P<0.005). There were no significant differences between 7W diode laser and 1W CO2 laser, 5W and 7W diode laser, or 1W and 2W CO2 laser in this regard. Conclusion: The results showed that enamel surface irradiation by CO2 and diode lasers increases the fluoride uptake. PMID:27123018

Fluoride-selective optical sensor based on aluminum(III)-octaethylporphyrin in thin polymeric film: further characterization and practical application.

PubMed

Badr, Ibrahim H A; Meyerhoff, Mark E

2005-10-15

More detailed analytical studies of a new fluoride-selective optical sensor based on the use of aluminum(III)-octaethylporphyrin and a lipophilic pH indicator (4',5'-dibromofluorescein octadecyl ester; ETH-7075) within a thin plasticized poly(vinyl chloride) film are reported. The sensor exhibits extraordinary optical selectivity for fluoride over a wide range of other anions, including anions with far more positive free energies of hydration (e.g., perchlorate, thiocyanate, nitrate, etc.). UV-visible spectrophotometric studies of the sensing films indicate that fluoride interacts with the Al(III) center of the porphyrin structure, yielding both a change in the Soret band lambda(max) of the porphyrin and a change in the protonation state of the pH indicator within the film. The same change in spectral properties of the metalloporphyrin occurs in the absence of added pH indicator or with added tetraphenylborate derivative anionic sites, but optical responses to fluoride in these cases are shown to be irreversible. The presence of the pH indicator and the simultaneous fluoride/proton coextraction equilibrium chemistry is shown to greatly enhance the reversibility of fluoride binding to the Al(III) porphyrin. Optical response toward fluoride can be observed in the range of 0.1 microM-1.6 mM. Optical selectivity coefficients of <10(-6) for common anions (e.g., sulfate, chloride, nitrate, etc.) and <10(-4) for perchlorate and thiocyanate are obtained. Measurements of fluoride in drinking water via the new optical sensor are shown to correlate well with values obtained for the same samples using a classical LaF3-based fluoride ion-selective electrode method.

Fluoride Selective Optical Sensor Based on Aluminum(III)-Octaethylporphyrin in Thin Polymeric Film: Further Characterization and Practical Application

PubMed Central

Badr, Ibrahim H. A.; Meyerhoff, Mark E.

2008-01-01

More detailed analytical studies of a new fluoride selective optical sensor based on the use of aluminum(III)-octaethylporphyrin and a lipophilic pH indicator (4′,5′-dibromofluorescein octadecyl ester; ETH-7075) within a thin plasticized poly(vinyl chloride) film are reported. The sensor exhibits extraordinary optical selectivity for fluoride over a wide range of other anions, including anions with far more positive free energies of hydration (e.g., perchlorate, thiocyanate, nitrate, etc.). UV-VIS spectrophotometric studies of the sensing films indicate that fluoride interacts with the Al(III) center of the porphyrin structure, yielding both a change in the Soret band λmax of the porphyrin as well as a change in the protonation state of the pH indicator within the film. The same change in spectral properties of the metalloporphyrin occurs in the absence of added pH indicator or with added tetraphenylborate derivative anionic sites, but optical responses to fluoride in these cases are shown to be irreversible. The presence of the pH indicator and the simultaneous fluoride/proton coextraction equilibrium chemistry is shown to greatly enhance the reversibility of fluoride binding to the Al(III) porphyrin. Optical response toward fluoride can be observed in the range of 0.1 μM to 1.6 mM. Optical selectivity coefficients of < 10−6 for common anions (e.g., sulfate, chloride, nitrate etc.) and < 10−4 for perchlorate and thiocyanate are obtained. Measurements of fluoride in drinking water via the new optical sensor are shown to correlate well with values obtained for the same samples using a classical LaF3 based fluoride ion-selective electrode method. PMID:16223262

Thermal treatment of electronic waste in a fluidised bed and chemical digestion of solid products.

PubMed

Woynarowska, Amelia; Żukowski, Witold; Żelazny, Sylwester

2016-07-01

The article presents the results of e-waste thermal treatment in a fluidised bed reactor and solid products digestion under acidic conditions. During the processes, measurements of carbon monoxide, carbon dioxide, volatile organic compounds, nitrogen oxides, sulphur dioxide, hydrogen chloride, hydrogen bromide, hydrogen cyanide, ammonia, phenol, aliphatic and aromatic hydrocarbons, hydrogen fluoride and phosgene were carried out. Several digestion tests of the solid residue in sulphuric acid (VI) at 25 °C-65 °C, for 55 min-24 h were conducted. In each case, the dilution method was used, i.e. preliminary digestion in concentrated sulphuric acid (VI) (95%) for 40 min, and then dilution to expected concentrations (30%-50%). Most preferred results were obtained using sulphuric acid (VI) with a target concentration of 40% at 65 °C, where the leaching degrees were 76.56% for copper, 71.67% for iron, 91.89% for zinc and 97.40% for tin. The time necessary to effectively carry out the digestion process was 220 min. © The Author(s) 2016.

Hydrothermal synthesis and characterization of hydroxyapatite and fluorhydroxyapatite nano-size powders.

PubMed

Montazeri, Leila; Javadpour, Jafar; Shokrgozar, Mohammad Ali; Bonakdar, Shahin; Javadian, Sayfoddin

2010-08-01

Pure hydroxyapatite (HAp) and fluoride-containing apatite powders (FHAp) were synthesized using a hydrothermal method. The powders were assessed by x-ray diffraction (XRD), Fourier transform infrared (FTIR), scanning electron microscope (SEM) and F-selective electrode. X-ray diffraction results revealed the formation of single phase apatite structure for all the compositions synthesized in this work. However, the addition of a fluoride ion led to a systematic shift in the (3 0 0) peak of the XRD pattern as well as modifications in the FTIR spectra. It was found that the efficiency of fluoride ion incorporation decreased with the increase in the fluoride ion content. Fluorine incorporation efficiency was around 60% for most of the FHAp samples prepared in the current study. Smaller and less agglomerated particles were obtained by fluorine substitution. The bioactivity of the powder samples with different fluoride contents was compared by performing cell proliferation, alkaline phosphatase (ALP) and Alizarin red staining assays. Human osteoblast cells were used to assess the cellular responses to the powder samples in this study. Results demonstrated a strong dependence of different cell activities on the level of fluoridation.

Highly selective biaryl cross-coupling reactions between aryl halides and aryl Grignard reagents: a new catalyst combination of N-heterocyclic carbenes and iron, cobalt, and nickel fluorides.

PubMed

Hatakeyama, Takuji; Hashimoto, Sigma; Ishizuka, Kentaro; Nakamura, Masaharu

2009-08-26

Combinations of N-heterocyclic carbenes (NHCs) and fluoride salts of the iron-group metals (Fe, Co, and Ni) have been shown to be excellent catalysts for the cross-coupling reactions of aryl Grignard reagents (Ar(1)MgBr) with aryl and heteroaryl halides (Ar(2)X) to give unsymmetrical biaryls (Ar(1)-Ar(2)). Iron fluorides in combination with SIPr, a saturated NHC ligand, catalyze the biaryl cross-coupling between various aryl chlorides and aryl Grignard reagents in high yield and high selectivity. On the other hand, cobalt and nickel fluorides in combination with IPr, an unsaturated NHC ligand, exhibit interesting complementary reactivity in the coupling of aryl bromides or iodides; in contrast, with these substrates the iron catalysts show a lower selectivity. The formation of homocoupling byproducts is suppressed markedly to less than 5% in most cases by choosing the appropriate metal fluoride/NHC combination. The present catalyst combinations offer several synthetic advantages over existing methods: practical synthesis of a broad range of unsymmetrical biaryls without the use of palladium catalysts and phosphine ligands. On the basis of stoichiometric control experiments and theoretical studies, the origin of the unique catalytic effect of the fluoride counterion can be ascribed to the formation of a higher-valent heteroleptic metalate [Ar(1)MF(2)]MgBr as the key intermediate in our proposed catalytic cycle. First, stoichiometric control experiments revealed the stark differences in chemical reactivity between the metal fluorides and metal chlorides. Second, DFT calculations indicate that the initial reduction of di- or trivalent metal fluoride in the wake of transmetalation with PhMgCl is energetically unfavorable and that formation of a divalent heteroleptic metalate complex, [PhMF(2)]MgCl (M = Fe, Co, Ni), is dominant in the metal fluoride system. The heteroleptic ate-complex serves as a key reactive intermediate, which undergoes oxidative addition with PhCl and releases the biaryl cross-coupling product Ph-Ph with reasonable energy barriers. The present cross-coupling reaction catalyzed by iron-group metal fluorides and an NHC ligand provides a highly selective and practical method for the synthesis of unsymmetrical biaryls as well as the opportunity to gain new mechanistic insights into the metal-catalyzed cross-coupling reactions.

Fluoride geochemistry of thermal waters in Yellowstone National Park: I. Aqueous fluoride speciation

USGS Publications Warehouse

Deng, Y.; Nordstrom, D. Kirk; McCleskey, R. Blaine

2011-01-01

Thermal water samples from Yellowstone National Park (YNP) have a wide range of pH (1–10), temperature, and high concentrations of fluoride (up to 50 mg/l). High fluoride concentrations are found in waters with field pH higher than 6 (except those in Crater Hills) and temperatures higher than 50 °C based on data from more than 750 water samples covering most thermal areas in YNP from 1975 to 2008. In this study, more than 140 water samples from YNP collected in 2006–2009 were analyzed for free-fluoride activity by ion-selective electrode (ISE) method as an independent check on the reliability of fluoride speciation calculations. The free to total fluoride concentration ratio ranged from <1% at low pH values to >99% at high pH. The wide range in fluoride activity can be explained by strong complexing with H+ and Al3+ under acidic conditions and lack of complexing under basic conditions. Differences between the free-fluoride activities calculated with the WATEQ4F code and those measured by ISE were within 0.3–30% for more than 90% of samples at or above 10−6 molar, providing corroboration for chemical speciation models for a wide range of pH and chemistry of YNP thermal waters. Calculated speciation results show that free fluoride, F−, and major complexes (HF(aq)0">HF(aq)0, AlF2+, AlF2+">AlF2+and AlF30">AlF30) account for more than 95% of total fluoride. Occasionally, some complex species like AlF4-">AlF4-, FeF2+, FeF2+">FeF2+, MgF+ and BF2(OH)2-">BF2(OH)2- may comprise 1–10% when the concentrations of the appropriate components are high. According to the simulation results by PHREEQC and calculated results, the ratio of main fluoride species to total fluoride varies as a function of pH and the concentrations and ratios of F and Al.

Implementing a geographical information system to assess endemic fluoride areas in Lamphun, Thailand

PubMed Central

Theerawasttanasiri, Nonthaphat; Taneepanichskul, Surasak; Pingchai, Wichain; Nimchareon, Yuwaree; Sriwichai, Sangworn

2018-01-01

Introduction Many studies have shown that fluoride can cross the placenta and that exposure to high fluoride during pregnancy may result in premature birth and/or a low birth weight. Lamphun is one of six provinces in Thailand where natural water fluoride (WF) concentrations >10.0 mg/L were found, and it was also found that >50% of households used water with high fluoride levels. Nevertheless, geographical information system (GIS) and maps of endemic fluoride areas are lacking. We aimed to measure the fluoride level of village water supplies to assess endemic fluoride areas and present GIS with maps in Google Maps. Methods A cross-sectional survey was conducted from July 2016 to January 2017. Purpose sampling was used to identify villages of districts with WF >10.0 mg/L in the Mueang Lamphun, Pasang, and Ban Thi districts. Water samples were collected with the geolocation measured by Smart System Info. Fluoride was analyzed with an ion-selective electrode instrument using a total ionic strength adjustment buffer. WF >0.70 mg/L was used to identify unsafe drinking water and areas with high endemic fluoride levels. Descriptive statistics were used to describe the findings, and MS Excel was used to create the GIS database. Maps were created in Google Earth and presented in Google Maps. Results We found that WF concentrations ranged between 0.10–13.60 mg/L. Forty-four percent (n=439) of samples were at unsafe levels (>0.70 mg/L), and. 54% (n=303) of villages and 46% (n=79,807) of households used the unsafe drinking water. Fifty percent (n=26) of subdistricts were classified as being endemic fluoride areas. Five subdistricts were endemic fluoride areas, and in those, there were two subdistricts in which every household used unsafe drinking water. Conclusion These findings show the distribution of endemic fluoride areas and unsafe drinking water in Lamphun. This is useful for health policy authorities, local governments, and villagers and enables collaboration to resolve these issues. The GIS data are available at https://drive.google.com/open?id=1mi4Pvomf5xHZ1MQjK44pdp2xXFw&usp=sharing. PMID:29398924

[Influence of water fluoride exposure on sex hormone binding globulin and testosterone in adult male].

PubMed

Zhou, Tong; Yang, Rupu; Li, Shihong; Zheng, Guoqing; Xi, Yu; Cheng, Xuemin; Hou, Jiaxiang; Cui, Liuxin; Ba, Yue

2013-03-01

To explore the influence of water fluoride exposure on sex hormone binding globulin (SHBG) and testosterone in adult male. Cross-sectional study was conducted in three villages of Tongxu county including high fluoride group (HFG), defluoridation project group (DFPG) and control group (CG) based on the fluoride concentration in drinking water. Adult male who were born and raised in the village and aged 18 - 50 years old were recruited using cluster sampling. Fasting blood and morning urine samples were collected. The fluoride levels in drinking water and urine were detected by fluoride-ion selective electrode method. Serum SHBG level was determined using enzyme-linked immunosorbent assay (ELISA). The chemical luminescence immune analysis method was used to detect serum testosterone content. Serum SHBG level was 47.85 nmol/L in CG, 31.37 nmol/L in DFPG and 24.52 nmol/L in HFG respectively. There were significant difference among of three groups (P < 0.05). Serum testosterone level was 3.69 ng/ml in CG, 4.61 ng/ml in DFPG and 4.83 ng/ml in HFG respectively. Serum testosterone level in HFG was significantly higher than that in CG (P < 0.05). Serum SHBG level in HFG has positive correlation with serum testosterone (r = 0.230, P = 0.049), which has not been observed in DFPG and CG. Long-time fluorine exposure may affect serum SHBG and testosterone level in adult male.

Impact of Drinking Water Fluoride on Human Thyroid Hormones: A Case- Control Study.

PubMed

Kheradpisheh, Zohreh; Mirzaei, Masoud; Mahvi, Amir Hossein; Mokhtari, Mehdi; Azizi, Reyhane; Fallahzadeh, Hossein; Ehrampoush, Mohammad Hassan

2018-02-08

The elevated fluoride from drinking water impacts on T 3 , T 4 and TSH hormones. The aim was study impacts of drinking water fluoride on T 3 , T 4 and TSH hormones inYGA (Yazd Greater Area). In this case- control study 198 cases and 213 controls were selected. Fluoride was determined by the SPADNS Colorimetric Method. T 3 , T 4 and TSH hormones tested in the Yazd central laboratory by RIA (Radio Immuno Assay) method. The average amount of TSH and T 3 hormones based on the levels of fluoride in two concentration levels 0-0.29 and 0.3-0.5 (mg/L) was statistically significant (P = 0.001 for controls and P = 0.001 for cases). In multivariate regression logistic analysis, independent variable associated with Hypothyroidism were: gender (odds ratio: 2.5, CI 95%: 1.6-3.9), family history of thyroid disease (odds ratio: 2.7, CI 95%: 1.6-4.6), exercise (odds ratio: 5.34, CI 95%: 3.2-9), Diabetes (odds ratio: 3.7, CI 95%: 1.7-8), Hypertension (odds ratio: 3.2, CI 95%: 1.3-8.2), water consumption (odds ratio: 4, CI 95%: 1.2-14). It was found that fluoride has impacts on TSH, T 3 hormones even in the standard concentration of less than 0.5 mg/L. Application of standard household water purification devices was recommended for hypothyroidism.

Chair-side preventive interventions in the Public Dental Service in Norway.

PubMed

Widström, E; Tillberg, A; Byrkjeflot, L I; Skudutyte-Rysstad, R

2016-08-26

Objective and setting In Norway, the Public Dental Service (PDS) caters for the young (<19 years) and smaller numbers of adults, mostly special needs patients. This study surveyed chair-side preventive measures used in the public clinics and compared them with recommendations in evidence-based guidelines in the neighbouring countries.Materials and methods After ethical approval, the regional Chief Dental Officers (CDOs) emailed questionnaires to their local clinics (N = 421) where the most experienced dentist and dental hygienist were asked to respond on behalf of the clinic. Answers were received from 256 clinics (response rate 61%). Altogether, 215 dentists and 166 dental hygienists answered.Results Of the respondents, 26% reported that their clinic had agreed guidelines on preventive treatment to be used by all staff. Oral hygiene and fluoride toothpaste recommendations were considered appropriate. Almost 60% claimed that flossing instructions were given to all children and adolescents and 40% that fluoride varnish was used on all the young. Fissure sealants were used after individual assessment (80%). A third of the respondents claimed that fluoride tablets and fluoride rinse were recommended for all or most children and fluoride rinses for adults, even in addition to regular use of fluoride toothpaste. Dental hygienists used all methods more often than dentists. On adults, preventive measures were more often used on individual assessment. Half (48%) of the respondents were interested in new evidence-based national guidelines on preventive care.Conclusions Chair-side preventive treatment measures were numerous in the well-resourced Norwegian PDS, but partly outdated.

The effect of normal pulsed Nd-YAG laser irradiation on pits and fissures in human teeth.

PubMed

Bahar, A; Tagomori, S

1994-01-01

The effects of normal pulsed Nd-YAG laser irradiation on the acid resistance of human dental enamel of pits and fissures, the cleaning of the pit and fissure contents and fluoride uptake into deep pits and fissures were examined. The acid resistance of the pit and fissure enamel was evaluated by the amount of dissolved calcium per square millimeter of the surface area. The pit and fissure enamel treated with laser irradiation obtained an acid resistance 30% higher than that of the unlased controls. The cleaning effect of laser irradiation on the pit and fissure contents was compared with chemicomechanical and mechanical methods. The laser irradiation was found to clean the pits and fissures to a greater depth without alterating the shape of pits and fissures, compared with the other two methods. The distribution of calcium, phosphorus and fluoride in the enamel of the pits and fissures was then measured by electron probe microanalyzer. At the entrance and in the deep part of the pits and fissures, the fluoride content of the enamel treated with acidulated phosphate fluoride after laser irradiation was higher than that of the enamel treated with acidulated phosphate fluoride alone. These results thus suggest that Nd-YAG laser irradiation might be effective in increasing the acid resistance of the pit and fissure enamel, while removing the pit and fissure debris contents and increasing the fluoride uptake into the pit and fissure enamel.

Fluorination of 1,2,3-, 1,2,4-, and 1,3,5-trihalobenzenes with potassium fluoride in dimethyl sulfone

USGS Publications Warehouse

Shiley, R.H.; Dickerson, D.R.; Finger, G.C.

1972-01-01

Three trifluorobenzenes were prepared by reaction of the corresponding trichlorobenzenes with potassium fluoride or pottassium fluoride-cesium fluoride mixtures in dimethyl sulfone. Molar yields were 12.8% for 1,2,3-, 8.3% for 1,2,4-, and 56.2% for 1,3,5-. Improved yields of the 1,2,3- (23.9%) and the 1,2,4- (34.0%) trifluorobenzenes were obtained from certain partially fluorinated intermediates. Several chlorofluorobenzene intermediates were obtained in goods yields by careful control of the reaction variables. The instability of the polyfluorobenzenes in the halogen-exchange reaction medium explains, in part, why only limited yields of the polyfluorobenzenes are obtained by using this method. ?? 1972.

Anaerobic digestion of citrus waste using two-stage membrane bioreactor

NASA Astrophysics Data System (ADS)

Millati, Ria; Lukitawesa; Dwi Permanasari, Ervina; Wulan Sari, Kartika; Nur Cahyanto, Muhammad; Niklasson, Claes; Taherzadeh, Mohammad J.

2018-03-01

Anaerobic digestion is a promising method to treat citrus waste. However, the presence of limonene in citrus waste inhibits anaerobic digestion process. Limonene is an antimicrobial compound and could inhibit methane forming bacteria that takes a longer time to recover than the injured acid forming bacteria. Hence, volatile fatty acids will be accumulated and methane production will be decreased. One way to solve this problem is by conducting anaerobic digestion process into two stages. The first step is aimed for hydrolysis, acidogenesis, and acetogenesis reactions and the second stage is aimed for methanogenesis reaction. The separation of the system would further allow each stage in their optimum conditions making the process more stable. In this research, anaerobic digestion was carried out in batch operations using 120 ml-glass bottle bioreactors in 2 stages. The first stage was performed in free-cells bioreactor, whereas the second stage was performed in both bioreactor of free cells and membrane bioreactor. In the first stage, the reactor was set into ‘anaerobic’ and ‘semi-aerobic’ conditions to examine the effect of oxygen on facultative anaerobic bacteria in acid production. In the second stage, the protection of membrane towards the cells against limonene was tested. For the first stage, the basal medium was prepared with 1.5 g VS of inoculum and 4.5 g VS of citrus waste. The digestion process was carried out at 55°C for four days. For the second stage, the membrane bioreactor was prepared with 3 g of cells that were encased and sealed in a 3×6 cm2 polyvinylidene fluoride membrane. The medium contained 40 ml basal medium and 10 ml liquid from the first stage. The bioreactors were incubated at 55°C for 2 days under anaerobic condition. The results from the first stage showed that the maximum total sugar under ‘anaerobic’ and ‘semi-aerobic’ conditions was 294.3 g/l and 244.7 g/l, respectively. The corresponding values for total volatile fatty acids were 3.8 g/l and 2.9 g/l, respectively. Methane production of citrus waste taken from the first stage under ‘anaerobic’ condition in membrane and free-cells bioreactors was 11.2 Nml and 7.2 Nml, respectively. Whereas, methane production of citrus waste taken from the first stage under ‘semi-aerobic’ condition in membrane and free-cells bioreactors was 8.8 Nml and 5.7 Nml, respectively. It can be seen from the results of the first stage that volatile fatty acids from ‘anaerobic’ condition was higher than that of ‘semi-aerobic’ condition. The absence of oxygen provides the optimal condition for growth and metabolism of facultative and obligatorily anaerobic bacteria in the first stage. Furthermore, polyvinylidene fluoride membrane was able to protect the cells from antimicrobial compounds.

Efficacy of Concomitant Therapy with Fluoride and Chlorhexidine Varnish on Remineralization of Incipient Lesions in Young Children

PubMed Central

Tandon, Shobha; Nayak, Rashmi; Ratnanag, P Venkat; Prajapati, Deepesh; Kamath, Namitha

2016-01-01

Aim To assess the effect of combined use of chlorhexidine and fluoride varnish on the remineralization of incipient carious lesions in young children. Materials and methods Twenty caries-active children (80 lesions) were randomly divided into four groups and subjected to initial examination. Caries status was assessed visually and with the aid of DIAGNOdent. Baseline enamel biopsies were obtained. Subjects of groups I and II received fluoride and chlorhexidine varnish respectively. Group III received both fluoride and chlorhexidine varnish alternatively, for a period of 4 weeks. Group IV served as the control. At 3-month follow-up, the incipient lesions were assessed again with DIAGNOdent and enamel biopsy. Results Increased calcium, phosphate, and fluoride levels were noticed in groups I, II, III compared to group IV, at the 3-month follow-up (p < 0.001). Conclusion The combined therapy with fluoride and chlorhex-idine varnish may be considered an alternative therapy for early reversal of incipient lesions. How to cite this article Naidu S, Tandon S, Nayak R, Ratnanag PV, Prajapati D, Kamath N. Efficacy of Concomitant Therapy with Fluoride and Chlorhexidine Varnish on Remineralization of Incipient Lesions in Young Children. Int J Clin Pediatr Dent 2016;9(4):296-302. PMID:28127159

Effect of Fluoride on Nickel-Titanium and Stainless Steel Orthodontic Archwires: An In-Vitro Study

PubMed Central

Heravi, Farzin; Moayed, Mohamad Hadi; Mokhber, Nima

2015-01-01

Objectives: The commonly used Nickel-Titanium (NiTi) archwires in orthodontic treatment are often exposed to fluoride-containing mouthwashes. The aim of this in-vitro study was to evaluate and compare the corrosion resistance of three commercially available NiTi archwires exposed to 0.05 wt% and 0.2 wt% fluoride mouthwashes. Materials and Methods: Three different types of NiTi archwires, 0.016″ in diameter, from Dentaurum, Global, and GAC, and a stainless steel archwire from Dentaurum were examined to assess their corrosion resistance in Fusayama-Meyer artificial saliva and in two other artificial saliva containing 0.05 wt% and 0.2 wt% sodium fluoride (NaF). After the primary setup of wires, they were tested by potentiodynamic and potentiostatic polarization and corrosion potential/time analyses. Their surfaces were evaluated using a scanning electronic microscope (SEM). Results: The results showed that all the wires were passive in artificial saliva. In contrast, by adding fluoride ions to the solution, the decrease in the archwires’ corrosion resistance was in direct proportion to the increase in fluoride concentration. Conclusion: The NiTi wires experienced deterioration of their corrosion properties under the effect of fluoride but not as much as the stainless steel archwires. PMID:26005454

Dental fluorosis in populations from Chiang Mai, Thailand with different fluoride exposures – Paper 1: assessing fluorosis risk, predictors of fluorosis and the potential role of food preparation

PubMed Central

2012-01-01

Background To determine the severity of dental fluorosis in selected populations in Chiang Mai, Thailand with different exposures to fluoride and to explore possible risk indicators for dental fluorosis. Methods Subjects were male and female lifetime residents aged 8–13 years. For each child the fluoride content of drinking and cooking water samples were assessed. Digital images were taken of the maxillary central incisors for later blind scoring for TF index (10% repeat scores). Interview data explored previous cooking and drinking water use, exposure to fluoride, infant feeding patterns and oral hygiene practices. Results Data from 560 subjects were available for analysis (298 M, 262 F). A weighted kappa of 0.80 was obtained for repeat photographic scores. The prevalence of fluorosis (TF 3+) for subjects consuming drinking and cooking water with a fluoride concentration of <0.9 ppm was 10.2%. For subjects consuming drinking and cooking water >0.9 ppm F the prevalence of fluorosis (TF 3+) rose to 37.3%. Drinking and cooking water at age 3, water used for infant formula and water used for preparing infant food all demonstrated an increase in fluorosis severity with increase in water fluoride level (p < 0.001). The probability estimate for the presentation of aesthetically significant fluorosis was 0.53 for exposure to high fluoride drinking (≥0.9 ppm) and cooking water (≥1.6 ppm). Conclusions The consumption of drinking water with fluoride content >0.9 ppm and use of cooking water with fluoride content >1.6 ppm were associated with an increased risk of aesthetically significant dental fluorosis. Fluoride levels in the current drinking and cooking water sources were strongly correlated with fluorosis severity. Further work is needed to explore fluorosis risk in relation to total fluoride intake from all sources including food preparation. PMID:22720834

Innovative Monitoring of Atmospheric Gaseous Hydrogen Fluoride

PubMed Central

Bonari, Alessandro; Pompilio, Ilenia; Monti, Alessandro; Arcangeli, Giulio

2016-01-01

Hydrogen fluoride (HF) is a basic raw material for a wide variety of industrial products, with a worldwide production capacity of more than three million metric tonnes. A novel method for determining particulate fluoride and gaseous hydrogen fluoride in air is presented herewith. Air was sampled using miniaturised 13 mm Swinnex two-stage filter holders in a medium-flow pumping system and through the absorption of particulate fluoride and HF vapours on cellulose ester filters uncoated or impregnated with sodium carbonate. Furthermore, filter desorption from the holders and the extraction of the pentafluorobenzyl ester derivative based on solid-phase microextraction were performed using an innovative robotic system installed on an xyz autosampler on-line with gas chromatography (GC)/mass spectrometry (MS). After generating atmospheres of a known concentration of gaseous HF, we evaluated the agreement between the results of our sampling method and those of the conventional preassembled 37 mm cassette (±8.10%; correlation coefficient: 0.90). In addition, precision (relative standard deviation for n = 10, 4.3%), sensitivity (0.2 μg/filter), and linearity (2.0–4000 μg/filter; correlation coefficient: 0.9913) were also evaluated. This procedure combines the efficiency of GC/MS systems with the high throughput (96 samples/day) and the quantitative accuracy of pentafluorobenzyl bromide on-sample derivatisation. PMID:27829835

High fluoride water in Bondo-Rarieda area of Siaya County, Kenya: a hydro-geological implication on public health in the Lake Victoria Basin

PubMed Central

2014-01-01

Background Only a few studies to evaluate groundwater fluoride in Eastern Africa have been undertaken outside the volcanic belt of the Great Eastern Africa Rift Valley. The extent and impact of water fluoride outside these regions therefore remain unclear. The current study evaluated fluoride levels in household water sources in Bondo-Rarieda Area in the Kenyan part of the Lake Victoria Basin (LVB) and highlighted the risk posed by water fluoride to the resident communities. The results, it was anticipated, will contribute to in-depth understanding of the fluoride problem in the region. Methods A total of 128 water samples were collected from different water sources from the entire study area and analyzed for fluoride content using ion-selective electrodes. Results Lake Victoria was the main water source in the area but dams and open pans (39.5%), boreholes and shallow wells (23.5%), and streams (18.5%) were the principal water sources outside walking distances from the lake. The overall mean fluoride content of the water exceeded recommended limits for drinking water. The mean water fluoride was highest in Uyoma (1.39±0.84 ppm), Nyang’oma (1.00±0.59 ppm) and Asembo (0.92±0.46 ppm) and lowest in Maranda Division (0.69±0.42 ppm). Ponds (1.41±0.82 ppm), springs (1.25±0.43 ppm), dams and open pans (0.96±0.79 ppm), and streams (0.95±0.41 ppm) had highest fluoride levels but lake and river water did not have elevated fluoride levels. Groundwater fluoride decreased with increasing distance from the lake indicating that water fluoride may have hydro-geologically been translocated into the region from geochemical sources outside the area. Conclusions Lake Victoria was the main water source for the residents of Bondo-Rarieda Area. Majority of in-land residents however used water from dams, open pans, boreholes, shallow wells, ponds and streams, which was generally saline and fluoridated. It was estimated that 36% of children living in this area, who consume water from ground sources from the area could be at the risk of dental fluorosis. PMID:24884434

Recovery of protactinium from molten fluoride nuclear fuel compositions

DOEpatents

Baes, C.F. Jr.; Bamberger, C.; Ross, R.G.

1973-12-25

A method is provided for separating protactinium from a molten fluonlde salt composition consisting essentially of at least one alkali and alkaline earth metal fluoride and at least one soluble fluoride of uranium or thorium which comprises oxidizing the protactinium in said composition to the + 5 oxidation state and contacting said composition with an oxide selected from the group consisting of an alkali metal oxide, an alkaline earth oxide, thorium oxide, and uranium oxide, and thereafter isolating the resultant insoluble protactinium oxide product from said composition. (Official Gazette)

Method of Evaluating the Thermal Stability of the Pyroelectric Properties of Polyvinylidene Fluoride Effects of Poling Temperature and Field

DTIC Science & Technology

1982-06-01

Stability of th Technical Report No. 18 Pyroelectric Properties of Po.iyvinylidene Fluoride Effects of Poling Temperature and Field 4’ p."ORING or6. RePORT... poled polyvinyylidene •=•- fluoride films has been meesured while the teMseratire was varied at a constant rate of ", 5 OC/min. fromn roan...influenced in a reproducible mLnner by the poling vari.- ables especiall the poliN teoperature. The measuremwnt is therefore (Cont.) DD , O൙ 1473

[Chronic combined effects of fluoride and arsenite on the Runx2 and downstream related factors of bone metabolism in rats].

PubMed

Hong, Feng; Zheng, Chong; Xu, De-gan; Qian, Ya-li

2013-09-01

To observe the chronic combined effects of sodium fluoride and sodium arsenite on the Runx2 and downstream related factors of bone metabolism in SD rats. SD rats were divided randomly into nine groups of 6 each by factorial experimental design (half female and half male) , and supplied with the different doses of fluoride, arsenite and fluoride plus arsenite containing in deionized water (untreated control containing 0 mg/kg fluoride and 0 mg/kg arsenite, and low-fluoride and high supplemented with 5 and 20 mg/kg fluoride, and low-arsenite and high supplemented with 2.5 and 10 mg/kg arsenite, and low-fluoride plus low-arsenite, and low-fluoride plus high-arsenite, and high-fluoride plus low-arsenite, and high-fluoride plus high-arsenite, respectively) . After 6 months exposure, the concentration of Runx2, matrix metallopeptidase 9 (MMP-9) ,Osterix, Receptor activator for nuclear factor-κ β ligand (RANKL) were detected by enzyme-linked immunosorbent assay method, respectively. There were no dental fluorosis found in the control group, low-arsenic group and high-arsenic group. There were significant differences in the constituent ratio of dental fluorosis among the rats from low-fluoride and high-fluoride (that is 5 rats out of 6 and 6 rats out of 6) compared with the control group (0 rat out of 6) (χ(2) = 8.57, 12.00, P < 0.05). The bone fluorine level increased with the increase of fluoride dose, the groups without fluoride supply (control group, low-arsenite and high-arsenite group's geometric mean (minimum-maximum) were 0.005 (0.003-0.009), 0.006 (0.003-0.021), 0.003 (0.002-0.100) mg/g, respectively), low-fluorine groups (low-fluoride group, low-fluoride plus low-arsenite, and low-fluoride plus high-arsenite group were 3.395 (2.416-5.871), 3.809 (1.471-7.799), 1.471 (1.473-6.732)mg/g, respectively) , the high-fluorine groups (high-fluoride, high-fluoride plus low-arsenite, and high-fluoride plus high-arsenite group were 70.086 (46.183-131.927), 69.925 (40.503-96.183), 40.503 (52.622-89.487) mg/g, respectively) and the differences between groups was significant (P < 0.05). The bone arsenic level increased with the increase of arsenite dose. The low-arsenic groups (low-arsenite group, low-arsenite plus low-fluoride, and low-arsenite plus high-fluoride group were 7.195 (5.060-9.860), 6.518 (2.960-12.130), 6.970 (3.400-9.730) µg/g, respectively), the high-arsenic groups (high-arsenite, high-arsenite plus low-fluoride, and high-fluoride plus high-arsenite group's geometric mean(minimum-maximum) were 8.823 (5.760-10.840), 9.470 (7.230-12.860), 8.321 (2.420-17.540) µg/g, respectively) were significantly higher than that in the groups without arsenic supply (control group, low-fluoride and high-fluoride group were 1.785 (0.300-3.750), 2.226 (1.410-3.980), 2.030 (1.040-3.850)µg/g, respectively) (P < 0.05). There was no significant difference of the bone arsenic concentration between low-arsenic and high arsenic group. There was significant positive correlation between fluoride concentration and Runx2, MMP-9, Osterix, RANKL level (the correlation coefficient was 0.647, 0.354, 0.582, 0.613 between fluorine gavage concentration and protein level, the correlation coefficient was 0.559,0.387, 0.487, 0.525 between bone fluorine concentration and protein level, respectively, P < 0.01). There was negative correlation between arsenite gavage concentration with Runx2 level (r = -0.527, P < 0.05) and was no correlation between arsenite gavage concentration with MMP-9, RANKL,Osterix level (P > 0.05). There was interaction between fluoride and arsenite to Runx2, MMP-9, RANKL,Osterix (F = 3.88, 15.66, 2.92, 6.42, respectively, P = 0.01, <0.01, 0.031, <0.01, respectively). The combined effects of fluoride and arsenic on the Runx2, MMP-9, RANKL, Osterix of bone metabolism showed antagonistic effects.

Atmosphere purification of radon and radon daughter elements

DOEpatents

Stein, L.

1974-01-01

A method of removing radon and radon daughter elements from an atmosphere containing these elements by passing the atmosphere through a bed of fluorinating compound whereby the radon and radon daughters are oxidized to their respective fluorides is discussed. These fluorides adhere to the fluorinating compound and are thus removed from the atmosphere which may then be recirculated. A method for recovering radon and separating radon from its daughter elements is also described. (Official Gazette)

The influence of salivary variables on fluoride retention in dental plaque exposed to a mineral-enriching solution.

PubMed

Kato, K; Nakagaki, H; Arai, K; Pearce, E I F

2002-01-01

This study was carried out to examine interindividual differences in salivary variables related to plaque accumulation and to estimate their influence on the fluoride retention in plaque in vivo by a mineral-enriching solution. Two saliva samples were taken from 10 subjects, once after brushing and once after 24 h without brushing. Calcium, phosphate and monofluorophosphatase (MFPase) activity in the saliva samples were determined. The salivary flow rate and the debris index were also recorded. After plaque had formed over 3 days within in situ plaque-generating devices, subjects were instructed to rinse with a mineral-enriching mouthrinse three times a day on 4 consecutive days. Plaque exposed to distilled water plus flavoring agents served as a control. Fluoride-free dentifrice was used during the experimental period. Twenty-four hours after the last rinsing, the samples were removed from the mouth, and fluoride and mineral distributions in plaque analyzed using a method previously reported by the authors. Salivary flow, MFPase activity and calcium concentration in saliva were significantly higher after 24 h of plaque accumulation. Rinsing with the mineral-enriching solution produced retention of fluoride and phosphate in the outer and middle layers of plaque. Salivary calcium concentration had a direct effect on fluoride uptake in plaque, but no obvious relationship was found between other salivary variables and the plaque fluoride retention. The salivary calcium effect may be due to enhanced bacterial cell wall binding of fluoride via calcium bridging. Copyright 2002 S. Karger AG, Basel

Cluster-randomized xylitol toothpaste trial for early childhood caries prevention

PubMed Central

Chi, Donald L.; Tut, Ohnmar K.; Milgrom, Peter

2013-01-01

Purpose We assessed the efficacy of supervised toothbrushing with xylitol toothpaste to prevent early childhood caries (ECC) and to reduce mutans streptococci (MS). Methods In this cluster-randomized efficacy trial, 4 Head Start classrooms in the Marshall Islands were randomly assigned to supervised toothbrushing with 1,400ppm/31% fluoride-xylitol (Epic Dental, Provo, UT) or 1,450ppm fluoride-sorbitol toothpaste (Colgate-Palmolive, New York, NY) (N=196 children, ages 4–5 yrs). We hypothesized no difference in efficacy between the two types of toothpaste. The primary outcome was primary molar d2-3mfs increment after 6 mos. A single examiner was blinded to classroom assignments. Two classrooms were assigned to the fluoride-xylitol group (85 children) and 2 classrooms to the fluoride-sorbitol group (83 children). The child-level analyses accounted for clustering. Results There was no difference between the two groups in baseline or end-of-trial mean d2-3mfs. The mean d2-3mfs increment was greater in the fluoride-xylitol group compared to the fluoride-sorbitol group (2.5 and 1.4 d2-3mfs, respectively), but the difference was not significant (95% CI:−0.17, 2.37;P=0.07). No adverse effects were reported. Conclusion After 6 mos, brushing with a low strength xylitol/fluoride toothpaste is no more efficacious in reducing ECC than a fluoride only toothpaste in a high caries risk child population. PMID:24709430

The role of TGFβ receptor 1-smad3 signaling in regulating the osteoclastic mode affected by fluoride.

PubMed

Yu, Haolan; Jiang, Ningning; Yu, XiuHua; Zhao, Zhitao; Zhang, Xiuyun; Xu, Hui

2018-01-15

Studies that have focused on the role TGFβ signaling plays in osteoclast activity are gradually increasing; however, literature is rare in terms of fluorosis. The aim of this study is to observe the role the TβR1/Smad3 pathway plays in fluoride regulating cellsosteoclast-like cells that are under the treatment of TGFβ receptor 1 kinase. The RANKL-mediated osteoclast-like cells from RAW264.7 cells were used as osteoclast precursor model. The profile of miRNA expression in fluoride-treated osteoclast-like cells exhibited 303 upregulated miRNAs, 61 downregulated miRNAs, and further drew 37 signaling pathway maps by KEGG and Biocarta pathway enrichment analysis. TGFβ and its downstream effectors were included among them. Osteoclast viability, formation and function were detected via MTT method, bone resorption pit and tartrate-resistant acid phosphatase (TRACP) staining, respectively. Results demonstrated that different doses of fluoride exhibited a biphasic effect on osteoclast cell viability, differentiation, formation and function. It indicated that a low dose of fluoride treatment stimulated them, but high dose inhibited them. SB431542 acted as TβR1 kinase inhibitor and blocked viability, formation and function of osteoclast-like cells regulated by fluoride. The expression of the osteoclast marker, RANK, and TβR1/Smad3 at gene and protein level was analyzed under fluoride with and without SB431542 treatment. Fluoride treatment indicated little effect on the RANK protein expression; however it significantly influenced TRACP expression in osteoclast-like cells. The stimulation of fluoride on the expression of Smad3 gene and phosphorylated Smad3 protein exhibited dose-dependent manner. SB431542 significantly impeded phosphorylation of Smad3 protein and TRACP expression in osteoclast-like cells that were exposed to fluoride. Our work demonstrated that TGFβ signaling played a key role in fluoride regulating osteoclast differentiation, formation and function. It elucidated that TβR1/Smad3 pathway participated in the mechanism of biphasic modulation of osteoclast mode regulated by fluoride. Copyright © 2017 Elsevier B.V. All rights reserved.

Fluoride ion recognition by chelating and cationic boranes.

PubMed

Hudnall, Todd W; Chiu, Ching-Wen; Gabbaï, François P

2009-02-17

Because of the ubiquity of fluoride ions and their potential toxicity at high doses, researchers would like to design receptors that selectively detect this anion. Fluoride is found in drinking water, toothpaste, and osteoporosis drugs. In addition, fluoride ions also can be detected as an indicator of uranium enrichment (via hydrolysis of UF(6)) or of the chemical warfare agent sarin, which releases the ion upon hydrolysis. However, because of its high hydration enthalpy, the fluoride anion is one of the most challenging targets for anion recognition. Among the various recognition strategies that are available, researchers have focused a great deal of attention on Lewis acidic boron compounds. These molecules typically interact with fluoride anions to form the corresponding fluoroborate species. In the case of simple triarylboranes, the fluoroborates are formed in organic solvents but not in water. To overcome this limitation, this Account examines various methods we have pursued to increase the fluoride-binding properties of boron-based receptors. We first considered the use of bifunctional boranes, which chelate the fluoride anion, such as 1,8-diborylnaphthalenes or heteronuclear 1-boryl-8-mercurio-naphthalenes. In these molecules, the neighboring Lewis acidic atoms can cooperatively interact with the anionic guest. Although the fluoride binding constants of the bifunctional compounds exceed those of neutral monofunctional boranes by several orders of magnitude, the incompatibility of these systems with aqueous media limits their utility. More recently, we have examined simple triarylboranes whose ligands are decorated by cationic ammonium or phosphonium groups. These cationic groups increase the electrophilic character of these boranes, and unlike their neutral analogs, they are able to complex fluoride in aqueous media. We have also considered cationic boranes, which form chelate complexes with fluoride anions. Our work demonstrates that Coulombic and chelate effects are additive and can be combined to boost the anion affinity of Lewis acidic hosts. The boron compounds that we have investigated present a set of photophysical and electrochemical properties that can serve to signal the fluoride-binding event. We can also apply this approach to cyanide complexation and are continuing our investigations in that area.

Spectral engineering of optical fiber through active nanoparticle doping

NASA Astrophysics Data System (ADS)

Lindstrom-James, Tiffany

The spectral engineering of optical fiber is a method of intentional doping of the core region in order to absorb/emit specific wavelengths of light therby providing enhanced performance over current fibers. Efforts here focused on developing an understanding of optically active nanoparticles based on alkaline earth fluorides that could be easily and homogeneously incorporated into the core of a silica based optical fiber preform and result in efficient and tailorable spectral emissions. Doped and undoped calcium, strontium and barium fluoride nanoparticles were successfully synthesized and characterized for their physical, chemical, and optical behavior. Distinct spectroscopic differences as a result of different host materials, varying rare earth doping levels and processing conditions, indicated the ability to influence the spectral behavior of the doped nanoparticle. By using photoluminescence to predict diffusion behavior, the application of a simple one dimensional model for diffusion provided a method for predicting the diffusion coefficient of europium ions in alkaline earth fluorides with order of magnitude accuracy. Modified chemical vapor deposition derived silica preforms were individually solution doped with europium doped alkaline earth fluoride nanoparticles. By using the rare earth doped alkaline earth fluoride nanoparticles as the dopant materials in the core of optical fiber preforms, the resultant optical properties of the glass were significantly influenced by their presence in the core. The incorporation of these rare earth doped alkaline earth fluoride nanoparticles was found to significantly influence the local chemical and structural environment about the rare earth ion, demonstrated homogeneity and uniform distribution of the rare earth dopant and resulted in specifically unique spectral behavior when compared to conventional doping methods. A more detailed structural model of the doped core glass region has been developed based on the spectral behavior of these active fiber preforms. It has been shown that rare earth doping of alkaline earth fluoride nanoparticles provides a material which can be 'tuned' to specific applications through the use of different host materials, processing conditions and doping levels of the rare earth and when used as dopant materials for active optical fibers, provides a means to tailor the optical behavior.

[Research on the relationship between populations' long-term exposure to fluoride in drinking water and bone fracture in China].

PubMed

Liang, C; Ji, R; Cao, J; Cheng, X

2001-09-01

There are contradictory reports on the prevalence of bone fractures associated with long-term fluoride exposure from drinking water. The prevalence of bone fracture in six rural areas of China and the exposure of fluoride in drinking water was investigated. The data including medical history and demographic information, bone fractures, fluoride content in drinking water, physical activity, cigarette smoking, alcohol consumption and dietary intakes were collected. A retrospective epidemiological study by using the same design, method, quality control and the same questionnaire was conducted. A total of 8266 male and female over 50 years of age were divided into 6 groups by the fluoride concentrations in drinking water. The subjects in each group exposed to different levels of fluoride (0.25-0.34, 0.58-0.73, 1.00-1.06, 1.45-2.19, 2.62-3.58 and 4.32-7.97 mg/L) were 1363, 1407, 1370, 1574, 1051 and 1501 respectively. It has been confirmed that drinking water was the only major source of fluoride exposure in the studied populations. The total bone fracture rates were 7.41%, 6.40%, 5.11%, 6.04%, 6.09% and 7.40% in each group. Natural bone fracture rates in each group were 3.01%, 2.21%, 1.31%, 1.65%, 1.43% and 3.66% respectively. The prevalence of bone fracture and water fluoride level appeared a U-shaped relationship. The prevalence of total bone fracture and natural bone fracture in the population with fluoride 1.00-1.06 mg/L in drinking water was the lowest, compared with the groups exposed to fluoride higher than 4.32 mg/L and lower than 0.73 mg/L. The highest prevalence of hip fracture was in the group with higher water fluoride (4.32-7.97 mg/L) exposure. In general, the prevalence of hip fracture was lower and stable up to 1.06 mg/L of fluoride in drinking water, and then it appeared to rise. Based on the data collected in this investigation, it is concluded that the long-term fluoride exposure from drinking water higher than 4.32 mg/L might increase the risk of overall fractures as well as hip fractures. The risk of overall fractures and natural fractures might be lower while the water fluoride level is at 1.00-1.06 mg/L, however, no protective benefits of fluoride for the risk of hip fracture was observed.

A novel fast ion chromatographic method for the analysis of fluoride in Antarctic snow and ice.

PubMed

Severi, Mirko; Becagli, Silvia; Frosini, Daniele; Marconi, Miriam; Traversi, Rita; Udisti, Roberto

2014-01-01

Ice cores are widely used to reconstruct past changes of the climate system. For instance, the ice core record of numerous water-soluble and insoluble chemical species that are trapped in snow and ice offer the possibility to investigate past changes of various key compounds present in the atmosphere (i.e., aerosol, reactive gases). We developed a new method for the quantitative determination of fluoride in ice cores at sub-μg L(-1) levels by coupling a flow injection analysis technique with a fast ion chromatography separation based on the "heart cut" column switching technology. Sensitivity, linear range (up to 60 μg L(-1)), reproducibility, and detection limit (0.02 μg L(-1)) were evaluated for the new method. This method was successfully applied to the analysis of fluoride at trace levels in more than 450 recent snow samples collected during the 1998-1999 International Trans-Antarctica Scientific Expedition traverse in East Antarctica at sites located between 170 and 850 km from the coastline.

Removal of fluoride from drinking water using aluminum hydroxide coated rice husk ash.

PubMed

Ganvir, Vivek; Das, Kalyan

2011-01-30

Fluoride content in groundwater that is greater than the WHO limit of 1.5mg/L, causes dental and skeletal fluorosis. In India, several states are affected with excess fluoride in groundwater. The problem is aggravated due to the lack of appropriate and user friendly defluoridation technology. Several fluoride removal techniques are reported in the literature amongst which the Nalgonda technique and use of activated alumina have been studied extensively. However a simple, efficient and cost effective technology is not available for widespread use in many affected regions. In this paper, we present a novel cost effective defluoridation method that is based on surface modification of rice husk ash (RHA) by coating aluminum hydroxide. RHA is obtained by burning rice/paddy husk which is an abundantly available and is an inexpensive raw material. The results showed excellent fluoride removal efficiency and the adsorption capacity was found to be between 9 and 10mg/g. Copyright © 2010 Elsevier B.V. All rights reserved.

Micro-computed tomographic analysis of progression of artificial enamel lesions in primary and permanent teeth after resin infiltration.

PubMed

Ozgul, Betul Memis; Orhan, Kaan; Oz, Firdevs Tulga

2015-09-01

We investigated inhibition of lesion progression in artificial enamel lesions. Lesions were created on primary and permanent anterior teeth (n = 10 each) and were divided randomly into two groups with two windows: Group 1 (window A: resin infiltration; window B: negative control) and Group 2 (window A: resin infiltration + fluoride varnish; window B: fluoride varnish). After pH cycling, micro-computed tomography was used to analyze progression of lesion depth and changes in mineral density. Resin infiltration and resin infiltration + fluoride varnish significantly inhibited progression of lesion depth in primary teeth (P < 0.05). Inhibition of lesion depth progression in permanent teeth was significantly greater after treatment with resin infiltration + fluoride varnish than in the negative control (P < 0.05). Change in mineral density was smaller in the resin infiltration and resin infiltration + fluoride varnish groups; however, the difference was not significant for either group (P > 0.05). Resin infiltration is a promising method of inhibiting progression of caries lesions.

Method of forming a relatively stable slip of silicon metal particles and yttrium containing particles

DOEpatents

Dickie, Ray A.; Mangels, John A.

1984-01-01

The method concerns forming a relatively stable slip of silicon metal particles and yttrium containing particles. In one embodiment, a casting slip of silicon metal particles is formed in water. Particles of a yttrium containing sintering aid are added to the casting slip. The yttrium containing sintering aid is a compound which has at least some solubility in water to form Y.sup.+3 ions which have a high potential for totally flocculating the silicon metal particles into a semiporous solid. A small amount of a fluoride salt is added to the casting slip which contains the yttrium containing sintering aid. The fluoride salt is one which will produce fluoride anions when dissolved in water. The small amount of the fluoride anions produced are effective to suppress the flocculation of the silicon metal particles by the Y.sup.+3 ions so that all particles remain in suspension in the casting slip and the casting slip has both an increased shelf life and can be used to cast articles having a relatively thick cross-section. The pH of the casting slip is maintained in a range from 7.5 to 9. Preferably, the fluoride salt used is one which is based on a monovalent cation such as sodium or ammonia. The steps of adding the yttrium containing sintering aid and the fluoride salt may be interchanged if desired, and the salt may be added to a solution containing the sintering aid prior to addition of the silicon metal particles.

Groundwater fluoride and dental fluorosis in southwestern Nigeria.

PubMed

Gbadebo, A M

2012-10-01

This study was carried out to assess the fluoride levels of groundwater from open wells, consumed by the residents of three communities located in two distinct geological terrains of southwestern Nigeria. Fluoride concentration was determined using spectrophotometric technique, while analysis of other parameters like temperature, pH and total dissolve solids followed standard methods. Results of the analysis indicated that groundwater samples from Abeokuta Metropolis (i.e., basement complex terrain) had fluoride content in the range of 0.65 ± 0.21 and 1.20 ± 0.14. These values were found to be lower than the fluoride contents in the groundwater samples from Ewekoro peri-urban and Lagos metropolis where the values ranged between 1.10 ± 0.14-1.45 ± 0.07 and 0.15 ± 0.07-2.20 ± 1.41 mg/l, respectively. The fluoride contents in almost all locations were generally higher than the WHO recommended 0.6 mg/l. Analysis of Duncan multiple range test indicated that there is similarity in the level of significance of fluoride contents between different locations of same geological terrain at p ≤ 0.05. It was also observed that fluoride distribution of groundwater samples from the different geological terrain was more dependent on factors like pH and TDS than on temperature. The result of the analyzed social demographic characteristics of the residents indicated that the adults (between the age of 20 and >40 years) showed dental decay than the adolescent (<20 years). This signifies incidence of dental fluorosis by the high fluoride content in the drinking water of the populace. Further investigation on all sources of drinking water and other causes of tooth decay in the area is suggested.

A PEGylated fluorescent turn-on sensor for detecting fluoride ions in totally aqueous media and its imaging in live cells.

PubMed

Zheng, Fangyuan; Zeng, Fang; Yu, Changmin; Hou, Xianfeng; Wu, Shuizhu

2013-01-14

Owing to the considerable significance of fluoride anions for health and environmental issues, it is of great importance to develop methods that can rapidly, sensitively and selectively detect the fluoride anion in aqueous media and biological samples. Herein, we demonstrate a robust fluorescent turn-on sensor for detecting the fluoride ion in a totally aqueous solution. In this study, a biocompatible hydrophilic polymer poly(ethylene glycol) (PEG) is incorporated into the sensing system to ensure water solubility and to enhance biocompatibility. tert-Butyldiphenylsilyl (TBDPS) groups were then covalently introduced onto the fluorescein moiety, which effectively quenched the fluorescence of the sensor. Upon addition of fluoride ion, the selective fluoride-mediated cleavage of the Si-O bond leads to the recovery of the fluorescein moiety, resulting in a dramatic increase in fluorescence intensity under visible light excitation. The sensor is responsive and highly selective for the fluoride anion over other common anions; it also exhibits a very low detection limit of 19 ppb. In addition, this sensor is operative in some real samples such as running water, urine, and serum and can accurately detect fluoride ions in these samples. The cytotoxicity of the sensor was determined to be Grade I toxicity according to United States Pharmacopoeia and ISO 10993-5, suggesting the very low cytotoxicity of the sensor. Moreover, it was found that the senor could be readily internalized by both HeLa and L929 cells and the sensor could be utilized to track fluoride level changes inside the cells. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Defluoridation of water using activated alumina in presence of natural organic matter via response surface methodology.

PubMed

Samarghandi, Mohammad Reza; Khiadani, Mehdi; Foroughi, Maryam; Zolghadr Nasab, Hasan

2016-01-01

Adsorption by activated alumina is considered to be one of the most practiced methods for defluoridation of freshwater. This study was conducted, therefore, to investigate the effect of natural organic matters (NOMs) on the removal of fluoride by activated alumina using response surface methodology. To the authors' knowledge, this has not been previously investigated. Physico-chemical characterization of the alumina was determined by scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET), Fourier transform infrared spectroscopy (FTIR), X-ray fluorescence (XRF), and X-ray diffractometer (XRD). Response surface methodology (RSM) was applied to evaluate the effect of single and combined parameters on the independent variables such as the initial concentration of fluoride, NOMs, and pH on the process. The results revealed that while presence of NOM and increase of pH enhance fluoride adsorption on the activated alumina, initial concentration of fluoride has an adverse effect on the efficiency. The experimental data were analyzed and found to be accurately and reliably fitted to a second-order polynomial model. Under optimum removal condition (fluoride concentration 20 mg/L, NOM concentration 20 mg/L, and pH 7) with a desirability value of 0.93 and fluoride removal efficiency of 80.6%, no significant difference was noticed with the previously reported sequence of the co-exiting ion affinity to activated alumina for fluoride removal. Moreover, aluminum residual was found to be below the recommended value by the guideline for drinking water. Also, the increase of fluoride adsorption on the activated alumina, as NOM concentrations increase, could be due to the complexation between fluoride and adsorbed NOM. Graphical abstract ᅟ.

Adsorption of fluoride to UiO-66-NH2 in water: Stability, kinetic, isotherm and thermodynamic studies.

PubMed

Lin, Kun-Yi Andrew; Liu, Yu-Ting; Chen, Shen-Yi

2016-01-01

To provide safe drinking water, fluoride in water must be removed and adsorption processes appear to be the most widely used method. Metal organic frameworks (MOFs) represent a new class of adsorbents that have been used in various adsorption applications. To study the adsorption mechanism of fluoride to MOFs in water and obtain related adsorption parameters, we synthesized a zirconium-based MOF with a primary amine group on its ligand, named UiO-66-NH2. The kinetics, adsorption isotherm and thermodynamics of fluoride adsorption to UiO-66-NH2 were investigated. The crystalline structure of UiO-66-NH2 remained intact and the local structure of zirconium in UiO-66-NH2 did not change significantly after being exposed to fluoride. The kinetics of the fluoride adsorption in UiO-66-NH2 could be well represented by the pseudo second order rate law. The enthalpy of the adsorption indicates that the F(-) adsorption to UiO-66-NH2 was classified as a physical adsorption. However, the comparison between the adsorption capacities of UiO-66-NH2 and UiO-66 suggests that the fluoride adsorption to UiO-66-NH2 might primarily involve a strong interaction between F(-) and the metal site. The fluoride adsorption capacity of UiO-66-NH2 was found to decrease when pH>7. While the presence of chloride/bromide ions did not noticeably change the adsorption capacity of UiO-66-NH2, the ionic surfactants slightly affected the adsorption capacity of UiO-66-NH2. These findings provide insights to further optimize the adsorption process for removal of fluoride using zirconium-based MOFs. Copyright © 2015 Elsevier Inc. All rights reserved.

NIOSH Manual of Analytical Methods (third edition). Fourth supplement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-08-15

The NIOSH Manual of Analytical Methods, 3rd edition, was updated for the following chemicals: allyl-glycidyl-ether, 2-aminopyridine, aspartame, bromine, chlorine, n-butylamine, n-butyl-glycidyl-ether, carbon-dioxide, carbon-monoxide, chlorinated-camphene, chloroacetaldehyde, p-chlorophenol, crotonaldehyde, 1,1-dimethylhydrazine, dinitro-o-cresol, ethyl-acetate, ethyl-formate, ethylenimine, sodium-fluoride, hydrogen-fluoride, cryolite, sodium-hexafluoroaluminate, formic-acid, hexachlorobutadiene, hydrogen-cyanide, hydrogen-sulfide, isopropyl-acetate, isopropyl-ether, isopropyl-glycidyl-ether, lead, lead-oxide, maleic-anhydride, methyl-acetate, methyl-acrylate, methyl-tert-butyl ether, methyl-cellosolve-acetate, methylcyclohexanol, 4,4'-methylenedianiline, monomethylaniline, monomethylhydrazine, nitric-oxide, p-nitroaniline, phenyl-ether, phenyl-ether-biphenyl mixture, phenyl-glycidyl-ether, phenylhydrazine, phosphine, ronnel, sulfuryl-fluoride, talc, tributyl-phosphate, 1,1,2-trichloro-1,2,2-trifluoroethane, trimellitic-anhydride, triorthocresyl-phosphate, triphenyl-phosphate, and vinyl-acetate.

The fluoridation of drinking water and hip fracture hospitalization rates in two Canadian communities.

PubMed Central

Suarez-Almazor, M E; Flowerdew, G; Saunders, L D; Soskolne, C L; Russell, A S

1993-01-01

OBJECTIVES. The purpose of this study was to compare hip fracture hospitalization rates between a fluoridated and a non-fluoridated community in Alberta, Canada: Edmonton, which has had fluoridated drinking water since 1967, and Calgary, which considered fluoridation in 1991 but is currently revising this decision. METHODS. Case subjects were all individuals aged 45 years or older residing in Edmonton or Calgary who were admitted to hospitals in Alberta between January 1, 1981, and December 31, 1987, and who had a discharge diagnosis of hip fracture. Edmonton rates were compared with Calgary rates, with adjustment for age and sex using the Edmonton population as a standard. RESULTS. The hip fracture hospitalization rate for Edmonton from 1981 through 1987 was 2.77 per 1000 person-years. The age-sex standardized rate for Calgary was 2.78 per 1000 person-years. No statistically significant difference was observed in the overall rate, and only minor differences were observed within age and sex subgroups, with the Edmonton rates being higher in males. CONCLUSIONS. These findings suggest that fluoridation of drinking water has no impact, neither beneficial nor deleterious, on the risk of hip fracture. PMID:8484450

Design and development of novel sensors for the determination of fluoride in water.

PubMed

Pillai, Aji Balan; Varghese, Benjamin; Madhusoodanan, Kottarathil Naduvil

2012-01-03

The presence of high fluoride content in drinking water is a serious health hazard as it may lead to fluorosis, a serious bone disease. Taking into account of the importance of fluoride an attempt has been made to design and develop simple, low cost, and easy to use sensors for the in situ determination of fluoride in water. Two novel absorption sensors have been fabricated and their characterization done. The first one is a light emitting diode based sensor and the other one is an evanescent wave fiber optic sensor. Reagents prepared using standard methods are mixed with water sample containing fluoride ion, and the peak absorption wavelength is found out. Suitable light sources and photo detectors have been selected, and the sensors are designed to give accurate results over a wide range. A microcontroller based setup has been fabricated for recording the concentration of the measured sample in parts per billion. Both sensors have been used to analyze water samples collected from various sources and regions. The results obtained have been compared with those obtained by using a spectrophotometer used for fluoride measurement and found to have one to one correspondence.

[Using fractional polynomials to estimate the safety threshold of fluoride in drinking water].

PubMed

Pan, Shenling; An, Wei; Li, Hongyan; Yang, Min

2014-01-01

To study the dose-response relationship between fluoride content in drinking water and prevalence of dental fluorosis on the national scale, then to determine the safety threshold of fluoride in drinking water. Meta-regression analysis was applied to the 2001-2002 national endemic fluorosis survey data of key wards. First, fractional polynomial (FP) was adopted to establish fixed effect model, determining the best FP structure, after that restricted maximum likelihood (REML) was adopted to estimate between-study variance, then the best random effect model was established. The best FP structure was first-order logarithmic transformation. Based on the best random effect model, the benchmark dose (BMD) of fluoride in drinking water and its lower limit (BMDL) was calculated as 0.98 mg/L and 0.78 mg/L. Fluoride in drinking water can only explain 35.8% of the variability of the prevalence, among other influencing factors, ward type was a significant factor, while temperature condition and altitude were not. Fractional polynomial-based meta-regression method is simple, practical and can provide good fitting effect, based on it, the safety threshold of fluoride in drinking water of our country is determined as 0.8 mg/L.

The next Stages in Researching Water Fluoridation: Evaluation and Surveillance

ERIC Educational Resources Information Center

Downer, Martin C.; Blinkhorn, Anthony S.

2007-01-01

Objective: (1) to provide a commentary on a conference held at the University of Manchester entitled Researching Water Fluoridation: Evaluation and Surveillance; (2) to synthesize from the proceedings of the meeting suggestions for future research and public health surveillance. Method: The main points and problematic issues raised by the speakers…

Processing fissile material mixtures containing zirconium and/or carbon

DOEpatents

Johnson, Michael Ernest; Maloney, Martin David

2013-07-02

A method of processing spent TRIZO-coated nuclear fuel may include adding fluoride to complex zirconium present in a dissolved TRIZO-coated fuel. Complexing the zirconium with fluoride may reduce or eliminate the potential for zirconium to interfere with the extraction of uranium and/or transuranics from fission materials in the spent nuclear fuel.

Caregivers Who Refuse Preventive Care for Their Children: The Relationship Between Immunization and Topical Fluoride Refusal

PubMed Central

2014-01-01

Objectives. The aim of this study was to examine caregivers’ refusal of preventive medical and dental care for children. Methods. Prevalence rates of topical fluoride refusal based on dental records and caregiver self-reports were estimated for children treated in 3 dental clinics in Washington State. A 60-item survey was administered to 1024 caregivers to evaluate the association between immunization and topical fluoride refusal. Modified Poisson regression models were used to estimate prevalence rate ratios (PRRs). Results. The prevalence of topical fluoride refusal was 4.9% according to dental records and 12.7% according to caregiver self-reports. The rate of immunization refusal was 27.4%. In the regression models, immunization refusal was significantly associated with topical fluoride refusal (dental record PRR = 1.61; 95% confidence interval [CI] = 1.32, 1.96; P < .001; caregiver self-report PRR = 6.20; 95% CI = 3.21, 11.98; P < .001). Caregivers younger than 35 years were significantly more likely than older caregivers to refuse both immunizations and topical fluoride (P < .05). Conclusions. Caregiver refusal of immunizations is associated with topical fluoride refusal. Future research should identify the behavioral and social factors related to caregiver refusal of preventive care with the goal of developing multidisciplinary strategies to help caregivers make optimal preventive care decisions for children. PMID:24832428

A long term study of fluoride release from metal-containing conventional and resin-modified glass-ionomer cements.

PubMed

Williams, J A; Billington, R W; Pearson, G J

2001-01-01

The objective of this study was to determine long term release of fluoride from a resin-modified glass-ionomer cement (RMGIC) (Fuji II LC (FLC)) compared with that from two conventional acid-base setting cements (HiDense (HD) and KetacSilver (KS)) marketed for similar restorative purposes. Fluoride release from discs of cement immersed in water or artificial saliva was measured for 2.7 years using an ion selective electrode technique. The RMGIC was affected by water if immersed immediately after setting. This is similar to conventional acid-base cements and the experimental method was designed to allow for this. Over the 2.7-year period, the RMGIC and HD released similar amounts of fluoride into both water and artificial saliva. In water, the RMGIC released the most fluoride, while in artificial saliva the highest release was from HD. KS released the least amount of fluoride in both immersing liquids. In artificial saliva, release was reduced to 17-25% of that found in water, with the RMGIC showing the greatest reduction. Both acid-base cured cements showed changes in colour over the 2.7-year span, while the colour of the RMGIC was stable. It was concluded that the RMGIC released equivalent or greater amounts of fluoride than the two acid-base cure glass-ionomers over a period of 2.7 years.

Invitro Evaluation of Fluoride Release from Hydroxyapatite Reinforced Glass Ionomer with or without Protective Coating

PubMed Central

Nandlal, Bhojraj

2016-01-01

Introduction Glass Ionomer Cement (GIC) is well known for its fluoride releasing property but has its own drawbacks of poor mechanical properties, sensitivity to initial desiccation and moisture contamination. To overcome these, search led to the reinforcement of hydroxyapatite and application of surface coating agent but their effect on fluoride release is still not clear. Aim To evaluate and compare the release of fluoride from Hydroxyapatite Reinforced Glass Ionomer (HA-GIC) with and without protective coating. Materials and Methods Specimens were prepared as follows- Eight percent by weight conventional glass ionomer was replaced by hydroxyapatite powder (HA) and an indigenous product was prepared (HA-GIC). This powder was mixed with liquid of conventional GIC and allowed to set, then G coat plus coating agent was applied in surface coated group and light cured. Fluoride release of the sample was measured every 24 hrs for seven days and weekly from 7th to 21st day using combination ion selective electrode. Results Mean values clearly reveal a significant decrease in the fluoride release from day 1 to day 21 for both the groups. Results of repeated measure ANOVA revealed statistically significant difference between two groups (p <0.001). Conclusion Coating the hydroxyapatite reinforced glass ionomer will allow for slow and steady release of fluoride for a long period of time into oral environment. PMID:27190957

Assessment of antifungal activity of herbal and conventional toothpastes against clinical isolates of Candida albicans

PubMed Central

Adwan, Ghaleb; Salameh, Yousef; Adwan, Kamel; Barakat, Ali

2012-01-01

Objective To detect the anticandidal activity of nine toothpastes containing sodium fluoride, sodium monofluorophosphate and herbal extracts as an active ingredients against 45 oral and non oral Candida albicans (C. albicans) isolates. Methods The antifungal activity of these toothpaste formulations was determined using a standard agar well diffusion method. Statistical analysis was performed using a statistical package, SPSS windows version 15, by applying mean values using one-way ANOVA with post-hoc least square differences (LSD) method. A P value of less than 0.05 was considered significant. Results All toothpastes studied in our experiments were effective in inhibiting the growth of all C. albicans isolates. The highest anticandidal activity was obtained from toothpaste that containing both herbal extracts and sodium fluoride as active ingredients, while the lowest activity was obtained from toothpaste containing sodium monofluorophosphate as an active ingredient. Antifungal activity of Parodontax toothpaste showed a significant difference (P< 0.001) against C. albicans isolates compared to toothpastes containing sodium fluoride or herbal products. Conclusions In the present study, it has been demonstrated that toothpaste containing both herbal extracts and sodium fluoride as active ingredients are more effective in control of C. albicans, while toothpaste that containing monofluorophosphate as an active ingredient is less effective against C. albicans. Some herbal toothpaste formulations studied in our experiments, appear to be equally effective as the fluoride dental formulations and it can be used as an alternative to conventional formulations for individuals who have an interest in naturally-based products. Our results may provide invaluable information for dental professionals. PMID:23569933

Thermodynamic Model of the Na-Al-Si-O-F Melts

NASA Astrophysics Data System (ADS)

Dolejs, D.; Baker, D. R.

2004-05-01

Fluorine is a common volatile element in magmatic-hydrothermal systems, but its solution mechanisms in highly polymerized silicate melts are poorly known. We have developed a thermodynamic model for fluorosilicate liquids which links experimentally determined phase equilibria and spectroscopic information on melt structure. The model is applicable to crystallization of fluoride minerals or fluoride-silicate immiscibility in natural felsic melts. Configurational properties of the liquid are defined by mixing of alkali fluoride, polyhedral aluminofluoride and silicofluoride species and non-bridging terminations of the silicate network. Abundances of individual structural species are described by a homogeneous equilibrium, representing melt depolymerization: F- (free) + O0 (bridging) = F0 (terminal) + O- (non-bridging), which is a replacement of one oxygen bridge, Si-O-Si, by two terminations, Si-F | Na-O-Si. In cryolite-bearing systems, the self-dissociation of octahedral aluminofluoride complexes: Na3[AlF6] = Na[AlF4] + 2 NaF, and the short-range order between (O,F)-corners and (Si,NaAl)-centers of tetrahedra: Si-O-Si + 2 [NaAl]-F = [NaAl]-O-[NaAl] + 2 Si-F, represent two additional interaction mechanisms. Portrayal of these equilibria in ternary Thompson reaction space allows to decrease the number of interaction mechanisms by linearly combining melt depolymerization with tetrahedral short-range order. In this formulation, the interaction parameters are incorporated directly in configurational properties, thus the complete melt speciation can be calculated, and the activities of any macroscopic species are readily derived. The model has been applied to subsystems of the Na2O-NaAlO2-SiO2-F2O-1 compositional space. Activity-composition relationships in the villiaumite-sodium silicate binaries require clustering of silicate tetrahedra in fluoride solvent. Phase-equilibria in cryolite-nepheline and cryolite-albite systems illustrate an overall increase of Na3AlF6 self-association in both joins. On the other hand, melt depolymerization by fluorine controls depression of silicate liquidi. The present model is useful for modeling the differentiation of peralkaline fluorine-bearing magmas and provides a starting point for predicting halide, carbonate, sulfide or sulfate saturation in natural melts.

Chemical hazards from acid crater lakes

NASA Astrophysics Data System (ADS)

van Bergen, M. J.; Sumarti, S.; Heikens, A.; Bogaard, T. A.; Hartiyatun, S.

2003-04-01

Acid crater lakes, which are hosted by a considerable number of active volcanoes, form a potential threat for local ecosystems and human health, as they commonly contain large amounts of dissolved chemicals. Subsurface seepage or overflow can lead to severe deterioration of the water quality of rivers and wells, as observations around several of these volcanoes have shown. The Ijen crater lake in East Java (Indonesia) is a striking example, as this reservoir of hyperacid (pH<0.5) sulphate, chloride and fluoride-rich water is the source of a ca. 50 km long acid river that transports substantial quantities of potentially toxic elements. A downstream trend of increasing pH from <1 to 2.5-4 is largely due to dilution with moderately acid springs (pH= ca. 4) and neutral tributaries (pH= ca. 7) inside the Ijen caldera. Geochemical controls that regulate element transport are subject to seasonal fluctuations in rainfall. Long-term monitoring has shown that fluoride levels pose some of the most severe environmental threats. Its concentration decreases from ca. 1300 mg/kg in the lake to ca. 10 mg/kg in a coastal area downstream, where virtually all of the river water is used for irrigating rice fields and other cropland. Apart from serious problems for agriculture, our survey of 55 drinking water wells in the irrigation area shows that 50% contain fluoride above the 1.5 ppm WHO limit, in line with the observation that dental fluorosis is widespread among the ca. 100,000 residents of the area. A conspicuous spatial correlation between fluoride concentrations and the irrigation system suggest that long-term (century) infiltration of irrigation water may have affected the quality of groundwater. Fluorosis is also a problem in some villages within the caldera, where well water sources may have a more direct subsurface connection with the lake system. From our observations we conclude that water-quality monitoring is especially needed for health reasons in volcanic areas where volatile elements, derived from passively degassing magma, are intercepted by (sub) surface water bodies.

Determination of total fluoride in HF/HNO3/H2SiF6 etch solutions by new potentiometric titration methods.

PubMed

Weinreich, Wenke; Acker, Jörg; Gräber, Iris

2007-03-30

In the photovoltaic industry the etching of silicon in HF/HNO(3) solutions is a decisive process for cleaning wafer surfaces or to produce certain surface morphologies like polishing or texturization. With regard to cost efficiency, a maximal utilisation of etch baths in combination with highest quality and accuracy is strived. To provide an etch bath control realised by a replenishment with concentrated acids the main constituents of these HF/HNO(3) etch solutions including the reaction product H(2)SiF(6) have to be analysed. Two new methods for the determination of the total fluoride content in an acidic etch solution based on the precipitation titration with La(NO(3))(3) are presented within this paper. The first method bases on the proper choice of the reaction conditions, since free fluoride ions have to be liberated from HF and H(2)SiF(6) at the same time to be detected by a fluoride ion-selective electrode (F-ISE). Therefore, the sample is adjusted to a pH of 8 for total cleavage of the SiF(6)(2-) anion and titrated in absence of buffers. In a second method, the titration with La(NO(3))(3) is followed by a change of the pH-value using a HF resistant glass-electrode. Both methods provide consistent values, whereas the analysis is fast and accurate, and thus, applicable for industrial process control.

Cariostatic effect of fluoride-containing restorative materials associated with fluoride gels on root dentin

PubMed Central

BORGES, Fernanda Tavares; CAMPOS, Wagner Reis da Costa; MUNARI, Lais Sant'ana; MOREIRA, Allyson Nogueira; PAIVA, Saul Martins; MAGALHÃES, Claudia Silami

2010-01-01

Secondary caries is still the main cause of restoration replacement, especially on the root surface Objective This in vitro study evaluated the cariostatic effects of fluoride-containing restorative materials associated with fluoride gels, on root dentin. Materials and Methods A randomized complete block design was used to test the effects of the restorative systems, fluoride regimes and the interactions among them at different distances from restoration margins. Standardized cavities were prepared on 240 bovine root specimens and randomly assigned to 15 groups of treatments (n=16). Cavities were filled with the following restorative materials: Ketac-Fil (3M-ESPE); Vitremer (3M-ESPE); Dyract/Prime & Bond NT (Dentsply); Charisma/Gluma One Bond (Heraeus Kulzer) and the control, Z250/Single Bond (3M-ESPE). The specimens were subjected to a pH-cycling model designed to simulate highcaries activity. During the cycles, 1.23% acidulated phosphate fluoride, 2.0% neutral sodium fluoride or deionized/distilled water (control) was applied to the specimens for 4 min. The surface Knoop microhardness test was performed before (KHNi) and after (KHNf) the pH cycles at 100, 200 and 300 mm from the margins. Dentin microhardness loss was represented by the difference in initial and final values (KHNi - KHNf). Data were analyzed by Friedman's and Wilcoxon's tests, ANOVA and Tukey's test (α=5%). Results The interaction of restorative systems and topical treatments was not significant (p=0.102). Dentin microhardness loss was lowest closer to the restoration. Ketac-fil presented the highest cariostatic effect. Vitremer presented a moderate effect, while Dyract and Charisma did not differ from the control, Z250. The effects of neutral and acidulated fluoride gels were similar to each other and higher than the control. Conclusion Conventional and resin-modified glass ionomer cements as well as neutral and acidulated fluoride gels inhibit the progression of artificial caries adjacent to restorations. The associated effect of fluoride-containing restorative materials and gels could not be demonstrated. PMID:21085800

High fluoride and low pH level have been detected in popular flavoured beverages in Malaysia

PubMed Central

HA Rahim, Zubaidah; M Bakri, Marina; HM, Zakir; IA, Ahmed; NA, Zulkifli

2014-01-01

Objective: In children, excessive ingestion of fluoride from different sources including bottled drinking water and flavoured beverages or soft drinks can lead to the development of dental fluorosis. In addition, the pH level of beverages is important. Low pH can cause dental erosion. In this study we explore the fluoride content and pH level of certain popular beverages available in Malaysian supermarkets and hawkers’ stalls. Methods: Bottled drinking water and selected popular flavoured packet drinks were purchased from a supermarket and the corresponding flavoured hawkers’ drinks, from a hawker’s stall in Kuala Lumpur. Fluoride and pH of the beverages were determined using digital fluoride meter and digital pH meter respectively. Results: It was found that fluoride content and pH level vary among the beverages. The mean fluoride content in both packet and hawkers’ drinks (7.64±1.88 mg/L, 7.51±1.60 mg/L, respectively) was approximately 7 times higher than the bottled drinking water (1.05±0.35 mg/L). Among the beverages, the tea packet drink was found to contain the highest amount of fluoride (13.02±0.23 mg/L). The mean pH of bottled-drinking water was near neutral (6.96±0.17), but acidic for both supermarket (4.78.00±0.49) and hawkers’ drinks (5.73±0.24). The lychee packet drink had the lowest pH level (2.97±0.03). Conclusions: Due to the wide variation of the fluoride content and pH level of the drinks tested in this study, it is recommended that steps should be taken to control the fluoride concentration and pH level in beverages if dental fluorosis and erosion are to be prevented. PMID:24772152

Comparative Evaluation of Fluoride Releasing Ability of Various Restorative Materials after the Application of Surface Coating Agents – An In-vitro Study

PubMed Central

Kishore, GVS; Sai-Sankar, AJ; Sridhar, M; Pranitha, Kakarla; Sai-Krishna, VS

2016-01-01

Introduction Fluoride plays a key role in prevention of dental caries and is also an essential element for oral health promotion both in children and adults. Aim The aim of the present study was to evaluate the effect of surface coating (petroleum jelly, G-Coat Plus) on the fluoride releasing property of conventional Glass Ionomer Cement (GIC) and Zirconomer. Materials and Methods A total of 30 disk shaped brass mold specimens (6±0.1mm in diameter and 2±0.1mm thickness) for each test group were fabricated with conventional GIC (Group A) and Zirconomer (Group B). These test groups were further divided into three subgroups of 10 each. The unprotected specimens act as control (Group A1 and B1), G-Coat Plus specimens as (Group A2 and B2) and for the remaining specimens petroleum jelly was applied (Group A3 and B3). Fluoride ion concentration was measured with a combination of fluoride ion specific electrode and ion analyzer for every 24 hours for 15 days. The data was statistically analyzed using Kruskal Wallis and Mann-Whitney U test. Results The Group B released significantly more fluoride than Group A. Among all the subgroups the greatest amount of fluoride was released from Group B1, in the first 24 hours followed by A1 and B2. The least was observed on 15th day with Group B3 and A3. Conclusion Both the tested materials (GIC and Zirconomer) used in the study exhibited fluoride release whether protected or unprotected with surface coating. Though there was a difference between the groups, the pattern of fluoride release was similar and continuous throughout the study period i.e., first the initial burst followed by sustained release. The results revealed Zirconomer released more fluoride and is comparable to conventional GIC. PMID:28209001

Comparison of the antimicrobial efficacy of chlorhexidine, sodium fluoride, fluoride with essential oils, alum, green tea, and garlic with lime mouth rinses on cariogenic microbes.

PubMed

Thomas, Ann; Thakur, Sneha; Mhambrey, Sanjana

2015-01-01

A number of natural mouth rinse formulations are being proposed as an alternative to the widely used chemical mouth rinses. To evaluate and compare the antimicrobial efficacy of chlorhexidine (0.2%), sodium fluoride (0.05%), fluoride with essential oils (0.05%), alum (0.02 M), green tea, and garlic with lime mouth rinses against Streptococcus mutans, lactobacilli, and Candida albicans. The three microbes were isolated from the saliva samples collected from children with severe early childhood caries. The zone of minimum inhibition was assessed using agar diffusion method. The data were statistically analyzed using SPSS software. Against S. mutans and lactobacilli, chlorhexidine mouth rinse was found to be the most effective as compared to sodium fluoride (P < 0.001, P < 0.001), fluoride with essential oils (P < 0.001, P < 0.001), alum (P < 0.001, P < 0.001), green tea (P < 0.001, P < 0.001), and garlic with lime (P < 0.001, P < 0.001) mouth rinses, respectively. But against C. albicans, garlic with lime mouth rinse was found to be the most effective as compared to chlorhexidine (P < 0.001), sodium fluoride (P < 0.001), fluoride with essential oils (P < 0.001), alum (P < 0.001), and green tea (P < 0.001) mouth rinses. Against S. mutans and lactobacilli, after chlorhexidine mouth rinse, garlic with lime mouth rinse was found to be significantly more effective than sodium fluoride (P = 0.053, P = 0.001), fluoride with essential oils (P < 0.001, P < 0.001), alum (P < 0.001, P < 0.001), and green tea (P < 0.001, P < 0.001) mouth rinses. As a natural mouth rinse, garlic with lime mouth rinse was found to be the most promising. However, further studies are needed in this field.

Acid demineralization susceptibility of dental enamel submitted to different bleaching techniques and fluoridation regimens.

PubMed

Salomão, Dlf; Santos, Dm; Nogueira, Rd; Palma-Dibb, Rg; Geraldo-Martins, Vr

2014-01-01

The aim of the current study was to assess the acid demineralization susceptibility of bleached dental enamel submitted to different fluoride regimens. One hundred bovine enamel blocks (6×6×3 mm) were randomly divided into 10 groups (n=10). Groups 1 and 2 received no bleaching. Groups 3 to 6 were submitted to an at-home bleaching technique using 6% hydrogen peroxide (HP; G3 and G4) or 10% carbamide peroxide (CP; G5 and G6). Groups 7 to 10 were submitted to an in-office bleaching technique using 35% HP (G7 and G8) or 35% CP (G9 and G10). During bleaching, a daily fluoridation regimen of 0.05% sodium fluoride (NaF) solution was performed on groups 3, 5, 7, and 9, while weekly fluoridation with a 2% NaF gel was performed on groups 4, 6, 8, and 10. The samples in groups 2 to 10 were pH cycled for 14 consecutive days. The samples from all groups were then assessed by cross-sectional Knoop microhardness at different depths from the outer enamel surface. The average Knoop hardness numbers (KHNs) were compared using one-way analysis of variance and Tukey tests (α=0.05). The comparison between groups 1 and 2 showed that the demineralization method was effective. The comparison among groups 2 to 6 showed the same susceptibility to acid demineralization, regardless of the fluoridation method used. However, the samples from groups 8 and 10 showed more susceptibility to acid demineralization when compared with group 2 (p<0.05). Groups 7 and 9 provided similar results to group 2, but the results of those groups were different when compared with groups 8 and 10. The use of 6% HP and 10% CP associated with daily or weekly fluoridation regimens did not increase the susceptibility of enamel to acid demineralization. However, the use of 35% HP and 35% CP must be associated with a daily fluoridation regimen, otherwise the in-office bleaching makes the bleached enamel more susceptible to acid demineralization.

Feasibility Study on a Process for Electroless Metal Deposition in Pits and Fissures of Teeth for Use in Preventive Dentistry.

DTIC Science & Technology

1980-08-01

been used in topical fluoride solutions applied to prevent caries . The use of SnF 2 . and similar chemical compounds, in the plating process appears to...Methods Tin fluoride solutions are prepared by dissolving SnF 2 in demineralized water at concentrations of 1, 5, 5.7, and 10%. The pH ranges from...saturated FeSO4 with or without 1 gpl thiourea a. .4 34 REFERENCES 1. P. Gron, "Chemistry of Topical Fluorides ", Caries Res. 11 (Suppl. 1): 172-204

Method for cleaning bomb-reduced uranium derbies

DOEpatents

Banker, John G.; Wigginton, Hubert L.; Beck, David E.; Holcombe, Cressie E.

1981-01-01

The concentration of carbon in uranium metal ingots induction cast from derbies prepared by the bomb-reduction of uranium tetrafluoride in the presence of magnesium is effectively reduced to less than 100 ppm by removing residual magnesium fluoride from the surface of the derbies prior to casting. This magnesium fluoride is removed from the derbies by immersing them in an alkali metal salt bath which reacts with and decomposes the magnesium fluoride. A water quenching operation followed by a warm nitric acid bath and a water rinse removes the residual salt and reaction products from the derbies.

Method for cleaning bomb-reduced uranium derbies

DOEpatents

Banker, J.G.; Wigginton, H.L.; Beck, D.E.; Holcombe, C.E.

The concentration of carbon in uranium metal ingots induction cast from derbies prepared by the bomb-reduction of uranium tetrafluoride in the presence of magnesium is effectively reduced to less than 100 ppM by removing residual magnesium fluoride from the surface of the derbies prior to casting. This magnesium fluoride is removed from the derbies by immersing them in an alkali metal salt bath which reacts with and decomposes the magnesium fluoride. A water quenching operation followed by a warm nitric acid bath and a water rinse removes the residual salt and reaction products from the derbies.

In vitro caries-inhibitory properties of a silver cermet.

PubMed

Swift, E J

1989-06-01

Recurrent caries is one of the primary causes of failure of dental restorations. One method for reducing the frequency and severity of this problem is the use of fluoride-releasing restorative materials. The glass-ionomer cements are a type of fluoride-releasing material. They have been used extensively in recent years for a variety of clinical applications. However, in comparison with other restorative materials such as amalgam and composite resins, glass ionomers have relatively poor physical properties. Sintering of silver particles to glass-ionomer powder is a means of improving these physical properties. The sintered material is called a silver-glass ionomer or silver cermet. This study examined the in vitro caries-inhibitory potential of a silver cement by means of two methods. First, long-term fluoride release was measured. Second, an artificial caries system was used for evaluation of caries inhibition by cerment restorations in extracted teeth. In comparison with a standard glass-ionomer restorative material, fluoride release from the cermet material was significantly less throughout a 12-month period. The results from the artificial caries system indicated that this decreased fluoride release corresponded with a lesser degree of caries inhibition. Lesions around cermet restorations in both enamel and root surfaces were significantly more severe than those around conventional glass-ionomer restorations. However, in comparison with amalgam and composite resin restorations, the cermet did have some cariostatic activity.

Effect of pretreatment with an Er:YAG laser and fluoride on the prevention of dental enamel erosion.

PubMed

dos Reis Derceli, Juliana; Faraoni-Romano, Juliana Jendiroba; Azevedo, Danielle Torres; Wang, Linda; Bataglion, César; Palma-Dibb, Regina Guenka

2015-02-01

The aim of this study was to evaluate the effect of the Er:YAG laser and its association with fluoride (1.23% acidulate phosphate fluoride gel) on the prevention of enamel erosion. Sixty specimens were obtained from bovine enamel (4 × 4 mm), which were ground flat, polished, and randomly divided into five groups according to the preventive treatments: control-fluoride application; L--Er:YAG laser; L+F--laser + fluoride; F+L--fluoride + laser; L/F--laser/fluoride simultaneously. Half of the enamel surface was covered with nail varnish (control area), and the other half was pretreated with one of the preventive strategies to subsequently be submitted to erosive challenge. When the laser was applied, it was irradiated for 10 s with a focal length of 4 mm and 60 mJ/2 Hz. Fluoride gel was applied for 4 min. Each specimen was individually exposed to regular Coca-Cola® for 1 min, four times/day, for 5 days. Wear analysis was performed with a profilometer, and demineralization was assessed with an optical microscope. Data were analyzed using the Kruskal-Wallis test (wear)/Dunn test and ANOVA/Fisher's exact tests. The group L/F was similar to control group. The other groups showed higher wear, which did not present differences among them. In the demineralization assessment, the groups F+L and L/F showed lower demineralization in relation to the other groups. It can be concluded that none preventive method was able to inhibit dental wear. The treatments L/F and F+L showed lower enamel demineralization.

The prevalence of dental fluorosis and exposure to fluoride in drinking water: A systematic review.

PubMed

Goodarzi, Fatemeh; Mahvi, Amir Hossein; Hosseini, Mostafa; Nedjat, Saharnaz; Nabizadeh Nodehi, Ramin; Kharazifard, Mohammad Javad; Parvizishad, Mina; Cheraghi, Zahra

2016-01-01

Background. Regarding the lack of comprehensive systematic review on the efficacy of water fluoridation and prevalence of dental fluorosis, the aim of the current research was to systematically study the prevalence of dental fluorosis at different levels of water fluoride in the world and lay emphasis on the amount of fluoride in drinking water. Methods. Studies were searched in PubMed, Scopus, SID, and IranMedex, with regard to inclusion criteria. Study validity was assessed with some checklists, and analyses were performed to ascertain the prevalence of dental fluorosis among individuals categorized in age groups. Results. Investigation of the heterogeneity and analysis of the subgroups revealed that in the 6-18 year age group, when water fluoride level was less than 0.7 ppm and there was exposure to water fluoride in the first 6-8 years of life, no significant heterogeneity was detected among the studies in this subgroup. Thus, the pooled estimation of dental fluorosis prevalence in this subgroup was 12.9% (95% CI: 7.5-18.3%). Furthermore, meta-regression indicated that the exposure time to fluoride in drinking water, or exposure to fluoride in supplements, diets, air, etc as well as the quality of studies had a significant relation to the difference in the prevalence of dental fluorosis. Conclusion. The results revealed no heterogeneity in just 2 subgroups, and the results of subgroups could be pooled in them. Furthermore, the number of studies included in this review considerably decreased by considering all the detected confounding factors, whereas other similar systematic reviews mentioned at most 2 factors.

Soluble fluoride levels in drinking water-a major risk factor of dental fluorosis among children in Bongo community of Ghana.

PubMed

Firempong, Ck; Nsiah, K; Awunyo-Vitor, D; Dongsogo, J

2013-03-01

The purpose of the study was to investigate the relationship between fluoride ions in drinking water and the incidence of dental fluorosis in some endemic areas of Bongo District, Ghana. Two hundred children were randomly selected from various homes and taken through a questionnaire. Their teeth were examined for the detection of dental fluorosis using the Dean's specific index. Samples of their permanent sources of water were taken for the determination of soluble fluoride levels by SPADNS spectrophotometric method. The study revealed that the incidence of dental fluorosis among the children in the main Bongo township was 63.0%, whereas villages outside the township recorded less than 10.0%. The respondents from the various communities had similar age group, educational background, sources of drinking water, oral hygiene habits and usage of oral health products, p-value > 0.05. However, there were statistically significant differences in the cases of dental fluorosis and fluoride ions among the communities, p-value < 0.05. The fluoride ion concentration in the Bongo township was above the WHO requirement of 1.50 ppm, whereas the nearby villages showed acceptable fluoride levels. Statistically, there was no significant relationship between the presence of dental fluorosis and the other characteristics, except the age group and fluoride ion concentration of the area. These findings strongly support the association between the dental fluorosis and the high fluoride levels in the underground water of Bongo community. Therefore, policy makers need to consider an alternative source of drinking water for the area.

Plasma Fluoride Level as a Predictor of Voriconazole-Induced Periostitis in Patients With Skeletal Pain

PubMed Central

Moon, Woo J.; Scheller, Erica L.; Suneja, Anupam; Livermore, Jacob A.; Malani, Anurag N.; Moudgal, Varsha; Kerr, Lisa E.; Ferguson, Eric; Vandenberg, David M.

2014-01-01

Background. Voriconazole is a triazole antifungal medication used for prophylaxis or to treat invasive fungal infections. Inflammation of the periosteum resulting in skeletal pain, known as periostitis, is a reported side effect of long-term voriconazole therapy. The trifluorinated molecular structure of voriconazole suggests a possible link between excess fluoride and periostitis, as elevated blood fluoride has been reported among patients with periostitis who received voriconazole. Methods. Two hundred sixty-four patients from Michigan were impacted by the multistate outbreak of fungal infections as a result of contaminated methylprednisolone injections. A retrospective study was conducted among 195 patients who received voriconazole therapy at St Joseph Mercy Hospital during this outbreak. Twenty-eight patients who received both bone scan and plasma fluoride measurements for skeletal pain were included in the statistical analyses. Increased tracer uptake on bone scan was considered positive for periostitis. The primary outcome measure was the correlation between plasma fluoride and bone scan results. Results. Blood fluoride (P < .001), alkaline phosphatase (P = .020), daily voriconazole dose (P < .001), and cumulative voriconazole dose (P = .027) were significantly elevated in patients who had periostitis compared with those who did not. Discontinuation or dose reduction of voriconazole resulted in improvement of pain in 89% of patients. Conclusions. High plasma fluoride levels coupled with skeletal pain among patients who are on long-term voriconazole therapy is highly suggestive of periostitis. Initial measurement of fluoride may be considered when bone scan is not readily available. Early detection should be sought, as discontinuation of voriconazole is effective at reversing the disease. PMID:24992954

Mathematical modeling of positron emission tomography (PET) data to assess radiofluoride transport in living plants following petiolar administration

DOE PAGES

Converse, Alexander K.; Ahlers, Elizabeth O.; Bryan, Tom W.; ...

2015-03-15

Background: Ion transport is a fundamental physiological process that can be studied non-invasively in living plants with radiotracer imaging methods. Fluoride is a known phytotoxic pollutant and understanding its transport in plants after leaf absorption is of interest to those in agricultural areas near industrial sources of airborne fluoride. Here we report the novel use of a commercial, high-resolution, animal positron emission tomography (PET) scanner to trace a bolus of [¹⁸F]fluoride administered via bisected petioles of Brassica oleracea, an established model species, to simulate whole plant uptake of atmospheric fluoride. This methodology allows for the first time mathematical compartmental modelingmore » of fluoride transport in the living plant. Radiotracer kinetics in the stem were described with a single-parameter free- and trapped-compartment model and mean arrival times at different stem positions were calculated from the free-compartment time-activity curves. Results: After initiation of administration at the bisected leaf stalk, [¹⁸F] radioactivity climbed for approximately 10 minutes followed by rapid washout from the stem and equilibration within leaves. Kinetic modeling of transport in the stem yielded a trapping rate of 1.5 +/- 0.3%/min (mean +/- s.d., n = 3), velocity of 2.2 +/- 1.1 cm/min, and trapping fraction of 0.8 +/- 0.5%/cm. Conclusion: Quantitative assessment of physiologically meaningful transport parameters of fluoride in living plants is possible using standard positron emission tomography in combination with petiolar radiotracer administration. Movement of free fluoride was observed to be consistent with bulk flow in xylem, namely a rapid and linear change in position with respect to time. Trapping, likely in the apoplast, was observed. Future applications of the methods described here include studies of transport of other ions and molecules of interest in plant physiology.« less

Mathematical modeling of positron emission tomography (PET) data to assess radiofluoride transport in living plants following petiolar administration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Converse, Alexander K.; Ahlers, Elizabeth O.; Bryan, Tom W.

Background: Ion transport is a fundamental physiological process that can be studied non-invasively in living plants with radiotracer imaging methods. Fluoride is a known phytotoxic pollutant and understanding its transport in plants after leaf absorption is of interest to those in agricultural areas near industrial sources of airborne fluoride. Here we report the novel use of a commercial, high-resolution, animal positron emission tomography (PET) scanner to trace a bolus of [¹⁸F]fluoride administered via bisected petioles of Brassica oleracea, an established model species, to simulate whole plant uptake of atmospheric fluoride. This methodology allows for the first time mathematical compartmental modelingmore » of fluoride transport in the living plant. Radiotracer kinetics in the stem were described with a single-parameter free- and trapped-compartment model and mean arrival times at different stem positions were calculated from the free-compartment time-activity curves. Results: After initiation of administration at the bisected leaf stalk, [¹⁸F] radioactivity climbed for approximately 10 minutes followed by rapid washout from the stem and equilibration within leaves. Kinetic modeling of transport in the stem yielded a trapping rate of 1.5 +/- 0.3%/min (mean +/- s.d., n = 3), velocity of 2.2 +/- 1.1 cm/min, and trapping fraction of 0.8 +/- 0.5%/cm. Conclusion: Quantitative assessment of physiologically meaningful transport parameters of fluoride in living plants is possible using standard positron emission tomography in combination with petiolar radiotracer administration. Movement of free fluoride was observed to be consistent with bulk flow in xylem, namely a rapid and linear change in position with respect to time. Trapping, likely in the apoplast, was observed. Future applications of the methods described here include studies of transport of other ions and molecules of interest in plant physiology.« less

Determining fluoride ions in ammonium desulfurization slurry using an ion selective electrode method

NASA Astrophysics Data System (ADS)

Luo, Zhengwei; Guo, Mulin; Chen, Huihui; Lian, Zhouyang; Wei, Wuji

2018-02-01

Determining fluoride ions in ammonia desulphurization slurry using a fluoride ion selective electrode (ISE) is investigated. The influence of pH was studied and the appropriate total ionic strength adjustment buffer and its dosage were optimized. The impact of Fe3+ concentration on the detection results was analyzed under preferable conditions, and the error analysis of the ISE method’s accuracy and precision for measuring fluoride ion concentration in the range of 0.5-2000 mg/L was conducted. The quantitative recovery of F- in ammonium sulfate slurry was assessed. The results showed that when pH ranged from 5.5˜6 and the Fe3+ concentration was less than 750 mg/L, the accuracy and precision test results with quantitative recovery rates of 92.0%-104.2% were obtained.

Modified zirconium-eriochrome cyanine R determination of fluoride

USGS Publications Warehouse

Thatcher, L.L.

1957-01-01

The Eriochrome Cyanine R method for determining fluoride in natural water has been modified to provide a single, stable reagent solution, eliminate interference from oxidizing agents, extend the concentration range to 3 p.p.m., and extend the phosphate tolerance. Temperature effect was minimized; sulfate error was eliminated by precipitation. The procedure is sufficiently tolerant to interferences found in natural and polluted waters to permit the elimination of prior distillation for most samples. The method has been applied to 500 samples.

Atmosphere purification of radon and radon daughter elements

DOEpatents

Stein, L.

1973-12-11

A method for purifying an atmosphere of radon and radon daughter elements which may be contained therein by contacting the atmosphere with a fluorinating solution, whereby the radon and radon daughters are oxidized to their respective fluorides is discussed. The fluorides dissolve in the fluorinating solutlon and are removed from the atmosphere, which may then be recirculated. (Official Gazette)

Development of Methods for Sampling and Analysis of Particulate and Gaseous Fluorides from Stationary Sources.

ERIC Educational Resources Information Center

Peters, E. T.; And Others

A study was conducted which has resulted in the development of tentative sampling and analysis of fluorides emitted from various stationary sources. The study was directed toward developing and understanding the kinds of species which are present in each source emission. The report presents the following information: review of the various unit…

Caries lesion remineralization with fluoride toothpastes and chlorhexidine - effects of application timing and toothpaste surfactant

PubMed Central

Almohefer, Sami A.; Levon, John A.; Gregory, Richard L.

2018-01-01

Abstract Habitual toothbrushing with fluoridated toothpaste followed by rinsing with antibacterial mouthwashes is a method to maintain good oral hygiene and to diminish the occurrence and severity of dental caries and periodontal disease. However, our understanding of how antimicrobial agents in mouthwashes affect fluoride-mediated caries lesion remineralization is still poor. Objective: The objectives of this in vitro study were a) to determine the effects of the waiting period of chlorhexidine (CHX) rinsing after fluoride toothpaste use and b) to further determine the effect of the type of toothpaste surfactant [sodium dodecyl sulfate (SDS) or cocamidopropyl betaine (CAPB)] on caries lesion remineralization associated with CHX rinsing. Material and Methods: Caries lesions were formed in bovine enamel specimens and assigned to 10 treatment groups (n=18) based on Vickers surface microhardness (VHN). Lesions were then pH-cycled for 10 days with daily regimen comprised of twice daily toothpaste slurry treatments (1150 ppm fluoride, with SDS or CAPB), followed by CHX solution treatments [0, 15, 30 or 60 minutes following slurry treatment or no CHX treatment (negative control)]. VHN was measured again and the extent of lesion remineralization calculated (∆VHN). Results: ∆VHN with SDS-toothpaste was significantly lower than with CAPB-toothpaste, indicating more remineralization for the CAPB-toothpaste. ∆VHN with 0-minute waiting time was significantly lower than with 30-minute waiting time and with negative control. Conclusions: The absence of CHX as an adjunct to fluoride toothpastes led to greater remineralization of enamel lesions compared with the immediate use of CHX treatment for both SDS- and CAPB-toothpastes. CAPB-toothpastes indicated significantly greater remineralization than SDS-toothpastes, and can be suggested for patients at high risk of caries. A 30-minute waiting time for CHX treatment is recommended after brushing.

Multi-Component Profiling of Trace Volatiles in Blood by Gas Chromatography/Mass Spectrometry with Dynamic Headspace Extraction

PubMed Central

Kakuta, Shoji; Yamashita, Toshiyuki; Nishiumi, Shin; Yoshida, Masaru; Fukusaki, Eiichiro; Bamba, Takeshi

2015-01-01

A dynamic headspace extraction method (DHS) with high-pressure injection is described. This dynamic extraction method has superior sensitivity to solid phase micro extraction, SPME and is capable of extracting the entire gas phase by purging the headspace of a vial. Optimization of the DHS parameters resulted in a highly sensitive volatile profiling system with the ability to detect various volatile components including alcohols at nanogram levels. The average LOD for a standard volatile mixture was 0.50 ng mL−1, and the average LOD for alcohols was 0.66 ng mL−1. This method was used for the analysis of volatile components from biological samples and compared with acute and chronic inflammation models. The method permitted the identification of volatiles with the same profile pattern as in vitro oxidized lipid-derived volatiles. In addition, the concentration of alcohols and aldehydes from the acute inflammation model samples were significantly higher than that for the chronic inflammation model samples. The different profiles between these samples could also be identified by this method. Finally, it was possible to analyze alcohols and low-molecular-weight volatiles that are difficult to analyze by SPME in high sensitivity and to show volatile profiling based on multi-volatile simultaneous analysis. PMID:26819905

Multi-Component Profiling of Trace Volatiles in Blood by Gas Chromatography/Mass Spectrometry with Dynamic Headspace Extraction.

PubMed

Kakuta, Shoji; Yamashita, Toshiyuki; Nishiumi, Shin; Yoshida, Masaru; Fukusaki, Eiichiro; Bamba, Takeshi

2015-01-01

A dynamic headspace extraction method (DHS) with high-pressure injection is described. This dynamic extraction method has superior sensitivity to solid phase micro extraction, SPME and is capable of extracting the entire gas phase by purging the headspace of a vial. Optimization of the DHS parameters resulted in a highly sensitive volatile profiling system with the ability to detect various volatile components including alcohols at nanogram levels. The average LOD for a standard volatile mixture was 0.50 ng mL(-1), and the average LOD for alcohols was 0.66 ng mL(-1). This method was used for the analysis of volatile components from biological samples and compared with acute and chronic inflammation models. The method permitted the identification of volatiles with the same profile pattern as in vitro oxidized lipid-derived volatiles. In addition, the concentration of alcohols and aldehydes from the acute inflammation model samples were significantly higher than that for the chronic inflammation model samples. The different profiles between these samples could also be identified by this method. Finally, it was possible to analyze alcohols and low-molecular-weight volatiles that are difficult to analyze by SPME in high sensitivity and to show volatile profiling based on multi-volatile simultaneous analysis.

A method for the solvent extraction of low-boiling-point plant volatiles.

PubMed

Xu, Ning; Gruber, Margaret; Westcott, Neil; Soroka, Julie; Parkin, Isobel; Hegedus, Dwayne

2005-01-01

A new method has been developed for the extraction of volatiles from plant materials and tested on seedling tissue and mature leaves of Arabidopsis thaliana, pine needles and commercial mixtures of plant volatiles. Volatiles were extracted with n-pentane and then subjected to quick distillation at a moderate temperature. Under these conditions, compounds such as pigments, waxes and non-volatile compounds remained undistilled, while short-chain volatile compounds were distilled into a receiving flask using a high-efficiency condenser. Removal of the n-pentane and concentration of the volatiles in the receiving flask was carried out using a Vigreux column condenser prior to GC-MS. The method is ideal for the rapid extraction of low-boiling-point volatiles from small amounts of plant material, such as is required when conducting metabolic profiling or defining biological properties of volatile components from large numbers of mutant lines.

Methods of using ionic liquids having a fluoride anion as solvents

DOEpatents

Pagoria, Philip [Livermore, CA; Maiti, Amitesh [San Ramon, CA; Gash, Alexander [Brentwood, CA; Han, Thomas Yong [Pleasanton, CA; Orme, Christine [Oakland, CA; Fried, Laurence [Livermore, CA

2011-12-06

A method in one embodiment includes contacting a strongly hydrogen bonded organic material with an ionic liquid having a fluoride anion for solubilizing the strongly hydrogen bonded organic material; and maintaining the ionic liquid at a temperature of about 90.degree. C. or less during the contacting. A method in another embodiment includes contacting a strongly hydrogen bonded organic material with an ionic liquid having an acetate or formate anion for solubilizing the strongly hydrogen bonded organic material; and maintaining the ionic liquid at a temperature of less than about 90.degree. C. during the contacting.

Improvement of a headspace solid phase microextraction-gas chromatography/mass spectrometry method for the analysis of wheat bread volatile compounds.

PubMed

Raffo, Antonio; Carcea, Marina; Castagna, Claudia; Magrì, Andrea

2015-08-07

An improved method based on headspace solid phase microextraction combined with gas chromatography-mass spectrometry (HS-SPME/GC-MS) was proposed for the semi-quantitative determination of wheat bread volatile compounds isolated from both whole slice and crust samples. A DVB/CAR/PDMS fibre was used to extract volatiles from the headspace of a bread powdered sample dispersed in a sodium chloride (20%) aqueous solution and kept for 60min at 50°C under controlled stirring. Thirty-nine out of all the extracted volatiles were fully identified, whereas for 95 other volatiles a tentative identification was proposed, to give a complete as possible profile of wheat bread volatile compounds. The use of an array of ten structurally and physicochemically similar internal standards allowed to markedly improve method precision with respect to previous HS-SPME/GC-MS methods for bread volatiles. Good linearity of the method was verified for a selection of volatiles from several chemical groups by calibration with matrix-matched extraction solutions. This simple, rapid, precise and sensitive method could represent a valuable tool to obtain semi-quantitative information when investigating the influence of technological factors on volatiles formation in wheat bread and other bakery products. Copyright © 2015 Elsevier B.V. All rights reserved.

Dental caries prevalence and its association with fluoride level in drinking water in Sana'a, Yemen

PubMed Central

Al-Akwa, Ameen Abdullah; Al-Maweri, Sadeq Ali

2018-01-01

Objectives: Dental caries is the most prevalent chronic condition affecting schoolchildren worldwide. This study is aimed to assess the prevalence of dental caries among schoolchildren in urban and rural districts of Sana'a governorate, Yemen, and to investigate the correlation between caries experience and level of fluoride in drinking water, age, gender, and residence. Materials and Methods: This school-based survey involved 17,599 schoolchildren (aged 6–12 years), of whom 9623 were boys and 7976 were girls. We used decay-missing-filled teeth/decay-filled teeth (DMFT/dft) indices to evaluate dental caries experience. In addition, fluoride concentration in drinking water was investigated. Results: Around 67.6% of children had dental caries. Children residing in urban districts had significantly higher mean scores of DMFT/dft than those in rural areas (P < 0.05). A significant negative correlation between caries experience and fluoride level was found (P < 0.05), with the lowest dft/DMFT scores at the optimum fluoride level of 0.61–2 ppm and the highest at two extremes, 0.0–0.4 ppm and >2 ppm. Conclusion: This survey found a very high prevalence of caries among schoolchildren in Yemen. There was also an inverse relation between dental caries experience and fluoride levels. PMID:29657520

Marginal regression models for clustered count data based on zero-inflated Conway-Maxwell-Poisson distribution with applications.

PubMed

Choo-Wosoba, Hyoyoung; Levy, Steven M; Datta, Somnath

2016-06-01

Community water fluoridation is an important public health measure to prevent dental caries, but it continues to be somewhat controversial. The Iowa Fluoride Study (IFS) is a longitudinal study on a cohort of Iowa children that began in 1991. The main purposes of this study (http://www.dentistry.uiowa.edu/preventive-fluoride-study) were to quantify fluoride exposures from both dietary and nondietary sources and to associate longitudinal fluoride exposures with dental fluorosis (spots on teeth) and dental caries (cavities). We analyze a subset of the IFS data by a marginal regression model with a zero-inflated version of the Conway-Maxwell-Poisson distribution for count data exhibiting excessive zeros and a wide range of dispersion patterns. In general, we introduce two estimation methods for fitting a ZICMP marginal regression model. Finite sample behaviors of the estimators and the resulting confidence intervals are studied using extensive simulation studies. We apply our methodologies to the dental caries data. Our novel modeling incorporating zero inflation, clustering, and overdispersion sheds some new light on the effect of community water fluoridation and other factors. We also include a second application of our methodology to a genomic (next-generation sequencing) dataset that exhibits underdispersion. © 2015, The International Biometric Society.

Synergistic effect of fluoride and laser irradiation for the inhibition of the demineralization of dental enamel

NASA Astrophysics Data System (ADS)

Lee, Raymond; Chan, Kenneth H.; Jew, Jamison; Simon, Jacob C.; Fried, Daniel

2017-02-01

Both laser irradiation and fluoride treatment alone are known to provide increased resistance to acid dissolution. CO2 lasers tuned to a wavelength of 9.3 μm can be used to efficiently convert the carbonated hydroxyapatite of enamel to a much more acid resistant purer phase hydroxyapatite (HAP). Further studies have shown that fluoride application to HAP yields fluoroapatite (FAP) which is even more resistant against acid dissolution. Previous studies show that CO2 lasers and fluoride treatments interact synergistically to provide significantly higher protection than either method alone, but the mechanism of interaction has not been elucidated. We recently observed the formation of microcracks or a "crazed" zone in the irradiated region that is resistant to demineralization using high-resolution microscopy. The microcracks are formed due to the slight contraction of enamel due to transformation of carbonated hydroxyapatite to the more acid resistant pure phase hydroxyapatite (HAP) that has a smaller lattice. In this study, we test the hypothesis that these small cracks will provide greater adhesion for topical fluoride for greater protection against acid demineralization.

Particle Morphology Effects on Flow Characteristics of PS304 Plasma Spray Coating Feedstock Powder Blend

NASA Technical Reports Server (NTRS)

Stanford, Malcolm K.; DellaCorte, Christopher; Eylon, Daniel

2002-01-01

The effects of BaF2-CaF 2 particle morphology on PS304 feedstock powder flow ability have been investigated. BaF2-CaF2 eutectic powders were fabricated by comminution (angular) and by gas atomization (spherical). The fluoride powders were added incrementally to the other powder constituents of the PS304 feedstock: nichrome, chromia, and silver powders. A linear relationship between flow time and concentration of BaF2-CaF2 powder was found. Flow of the powder blend with spherical BaF2-CaF2 was better than the angular BaF2-CaF2. Flow ability of the powder blend with angular fluorides decreased linearly with increasing fluoride concentration. Flow of the powder blend with spherical fluorides was independent of fluoride concentration. Results suggest that for this material blend, particle morphology plays a significant role in powder blend flow behavior, offering potential methods to improve powder flow ability and enhance the commercial potential. These findings may have applicability to other difficult-to-flow powders such as cohesive ceramics.

A new perspective on metals and other contaminants in fluoridation chemicals*

PubMed Central

Mullenix, Phyllis J

2014-01-01

Background: Fluoride additives contain metal contaminants that must be diluted to meet drinking water regulations. However, each raw additive batch supplied to water facilities does not come labeled with concentrations per contaminant. This omission distorts exposure profiles and the risks associated with accidents and routine use. Objectives: This study provides an independent determination of the metal content of raw fluoride products. Methods: Metal concentrations were analyzed in three hydrofluorosilicic acid (HFS) and four sodium fluoride (NaF) samples using inductively coupled plasma-atomic emission spectrometry. Arsenic levels were confirmed using graphite furnace atomic absorption analysis. Results: Results show that metal content varies with batch, and all HFS samples contained arsenic (4.9–56.0 ppm) or arsenic in addition to lead (10.3 ppm). Two NaF samples contained barium (13.3–18.0 ppm) instead. All HFS (212–415 ppm) and NaF (3312–3630 ppm) additives contained a surprising amount of aluminum. Conclusions: Such contaminant content creates a regulatory blind spot that jeopardizes any safe use of fluoride additives. PMID:24999851

Dietary Fluoride Intake and Associated Skeletal and Dental Fluorosis in School Age Children in Rural Ethiopian Rift Valley

PubMed Central

Kebede, Aweke; Retta, Negussie; Abuye, Cherinet; Whiting, Susan J.; Kassaw, Melkitu; Zeru, Tesfaye; Tessema, Masresha; Kjellevold, Marian

2016-01-01

An observational study was conducted to determine dietary fluoride intake, diet, and prevalence of dental and skeletal fluorosis of school age children in three fluorosis endemic districts of the Ethiopian Rift Valley having similar concentrations of fluoride (F) in drinking water (~5 mg F/L). The duplicate plate method was used to collect foods consumed by children over 24 h from 20 households in each community (n = 60) and the foods, along with water and beverages, were analyzed for fluoride (F) content. Prevalence of dental and skeletal fluorosis was determined using presence of clinical symptoms in children (n = 220). Daily dietary fluoride intake was at or above tolerable upper intake level (UL) of 10 mg F/day and the dietary sources (water, prepared food and beverages) all contributed to the daily fluoride burden. Urinary fluoride in children from Fentale and Adamitulu was almost twice (>5 mg/L) the concentration found in urine from children from Alaba, where rain water harvesting was most common. Severe and moderate dental fluorosis was found in Alaba and Adamitulu, the highest severity and prevalence being in the latter district where staple foods were lowest in calcium. Children in all three areas showed evidence of both skeletal and non-skeletal fluorosis. Our data support the hypothesis that intake of calcium rich foods in addition to using rain water for household consumption and preparation of food, may help in reducing risk of fluorosis in Ethiopia, but prospective studies are needed. PMID:27472351

Dietary Fluoride Intake and Associated Skeletal and Dental Fluorosis in School Age Children in Rural Ethiopian Rift Valley.

PubMed

Kebede, Aweke; Retta, Negussie; Abuye, Cherinet; Whiting, Susan J; Kassaw, Melkitu; Zeru, Tesfaye; Tessema, Masresha; Kjellevold, Marian

2016-07-26

An observational study was conducted to determine dietary fluoride intake, diet, and prevalence of dental and skeletal fluorosis of school age children in three fluorosis endemic districts of the Ethiopian Rift Valley having similar concentrations of fluoride (F) in drinking water (~5 mg F/L). The duplicate plate method was used to collect foods consumed by children over 24 h from 20 households in each community (n = 60) and the foods, along with water and beverages, were analyzed for fluoride (F) content. Prevalence of dental and skeletal fluorosis was determined using presence of clinical symptoms in children (n = 220). Daily dietary fluoride intake was at or above tolerable upper intake level (UL) of 10 mg F/day and the dietary sources (water, prepared food and beverages) all contributed to the daily fluoride burden. Urinary fluoride in children from Fentale and Adamitulu was almost twice (>5 mg/L) the concentration found in urine from children from Alaba, where rain water harvesting was most common. Severe and moderate dental fluorosis was found in Alaba and Adamitulu, the highest severity and prevalence being in the latter district where staple foods were lowest in calcium. Children in all three areas showed evidence of both skeletal and non-skeletal fluorosis. Our data support the hypothesis that intake of calcium rich foods in addition to using rain water for household consumption and preparation of food, may help in reducing risk of fluorosis in Ethiopia, but prospective studies are needed.

Effect of Catalase and Sodium Fluoride on Human Enamel bleached with 35% Carbamide Peroxide

PubMed Central

Shigli, Anand L; Sharma, Divya S; Thakur, Gagan

2015-01-01

ABSTRACT Aim: To evaluate the effects of postbleaching antioxidant application fluoridation treatment on the surface morphology and microhardness of human enamel. Materials and methods: Ten freshly extracted human maxillary central incisors were cut at cementoenamel junction. Crown portion was sectioned into six slabs which were divided into five groups: group A – untreated controls; group B – 35% carbamide peroxide (CP); group C – 35% CP and catalase; group D – treatment with 35% CP and 5% sodium fluoride; group E – 35% CP, catalase and 5% sodium fluoride. Thirty-five percent carbamide peroxide application included two applications of 30 minutes each at a 5-day interval. After treatment, the slabs were thoroughly washed with water for 10 seconds and stored in artificial saliva at 37°C until the next treatment. Two percent sodium fluoride included application for 5 minutes. Three catalase included application for 3 minutes. Results: After 5 days, groups B and C showed significantly decreased enamel microhardness compared to control. Group D specimens showed relatively less reduction in enamel micro-hardness than group C specimens. There is a marked increase in enamel microhardness in group E specimens. Conclusions: Fluoride take up was comparatively enhanced after catalase application resulting in less demineralization and increased microhardness. How to cite this article: Thakur R, Shigli AL, Sharma DS, Thakur G. Effect of Catalase and Sodium Fluoride on Human Enamel bleached with 35% Carbamide Peroxide. Int J Clin Pediatr Dent 2015;8(1):12-17. PMID:26124575

Effects of gaseous fluoride on Delicious and Golden Delicious apples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, M.J.

1973-01-01

Atmospheric fluorides were monitored in apple and other fruit orchards around two adjacent sources of fluoride emissions. Delicious and Golden Delicious trees were fumigated with low (4.6-4.7 micrograms F/cu m) fluoride levels once, twice, or three times a week. However, both methods were adequate in the determination of the fluoride distribution pattern in the study area. Considerably higher levels of fluoride were detected at sampling sites downwind of the emission sources. Fluoride-induced tip necrosis on apple leaves was observed in one orchard where a mean seasonal limed filter paper value of 82.4 micrograms F/d sq m/mo and 22.5 F inmore » the washed foliage were recorded. Tip necrosis increased as the F level and frequency of exposure increased. Leaf respiration was inhibited at the lower but not the higher F fumigation level. Fruit respiration was stimulated to equal levels by the two F concentrations used. A trend toward increased inhibition of fruit ethylene production at lower exposure factors (concentration times time) was observed. The loss of green color in the skin of treated fruits was retarded relative to an increase in the F level and the exposure frequency. With the exception of leaf respiration, where an inverse relationship was found, the degree of response with respect to leaf injury, fruit respiration, and color were directly affected by the exposure factor used. Within the scope of this study, fruit shape, firmness, and soluble solids were not affected by the treatments.« less

Fluoride Consumption and Its Impact on Oral Health

PubMed Central

Jiménez-Farfán, María Dolores; Hernández-Guerrero, Juan Carlos; Juárez-López, Lilia Adriana; Jacinto-Alemán, Luis Fernando; de la Fuente-Hernández, Javier

2011-01-01

Objective The purpose of this study was to evaluate caries and dental fluorosis among Mexican preschoolers and school-aged children in a non-endemic zone for fluorosis and to measure its biological indicators. Methods DMFT, DMFS, dmft, dmfs, and CDI indexes were applied. Fluoride urinary excretion and fluoride concentrations in home water, table salt, bottled water, bottled drinks, and toothpaste were determined. Results Schoolchildren presented fluorosis (CDI = 0.96) and dental caries (DMFT = 2.64 and DMFS = 3.97). Preschoolers presented dmft = 4.85 and dmfs = 8.80. DMFT and DMFS were lower in children with mild to moderate dental fluorosis (DF). Variable fluoride concentrations were found in the analyzed products (home water = 0.18–0.44 ppm F, table salt = 0–485 ppm F, bottled water = 0.18–0.47 ppm F, juices = 0.08–1.42 ppm F, nectars = 0.07–1.30 ppm F, bottled drinks = 0.10–1.70 ppm F, toothpaste = 0–2,053 ppm F). Mean daily fluoride excretion was 422 ± 176 μg/24 h for schoolchildren and 367 ± 150 μg/24 h for preschoolers. Conclusions Data from our study show that, despite values of excretion within an optimal fluoride intake range, the prevalence of caries was significant in both groups, and 60% of the 11- to 12-year-old children presented with dental fluorosis. In addition, variable fluoride concentrations in products frequently consumed by children were found. PMID:21318021

Ammonium Fluoride Mediated Synthesis of Anhydrous Metal Fluoride-Mesoporous Carbon Nanocomposites for High-Performance Lithium Ion Battery Cathodes.

PubMed

Chun, Jinyoung; Jo, Changshin; Sahgong, Sunhye; Kim, Min Gyu; Lim, Eunho; Kim, Dong Hyeon; Hwang, Jongkook; Kang, Eunae; Ryu, Keun Ah; Jung, Yoon Seok; Kim, Youngsik; Lee, Jinwoo

2016-12-28

Metal fluorides (MF x ) are one of the most attractive cathode candidates for Li ion batteries (LIBs) due to their high conversion potentials with large capacities. However, only a limited number of synthetic methods, generally involving highly toxic or inaccessible reagents, currently exist, which has made it difficult to produce well-designed nanostructures suitable for cathodes; consequently, harnessing their potential cathodic properties has been a challenge. Herein, we report a new bottom-up synthetic method utilizing ammonium fluoride (NH 4 F) for the preparation of anhydrous MF x (CuF 2 , FeF 3 , and CoF 2 )/mesoporous carbon (MSU-F-C) nanocomposites, whereby a series of metal precursor nanoparticles preconfined in mesoporous carbon were readily converted to anhydrous MF x through simple heat treatment with NH 4 F under solventless conditions. We demonstrate the versatility, lower toxicity, and efficiency of this synthetic method and, using XRD analysis, propose a mechanism for the reaction. All MF x /MSU-F-C prepared in this study exhibited superior electrochemical performances, through conversion reactions, as the cathode for LIBs. In particular, FeF 3 /MSU-F-C maintained a capacity of 650 mAh g -1 FeF3 across 50 cycles, which is ∼90% of its initial capacity. We expect that this facile synthesis method will trigger further research into the development of various nanostructured MF x for use in energy storage and other applications.

Glass ionomer ART sealant and fluoride-releasing resin sealant in fissure caries prevention – results from a randomized clinical trial

PubMed Central

2014-01-01

Background The relative performance of ART sealant and fluoride-releasing resin sealant in preventing fissure caries in permanent molars was compared in a randomized clinical trial conducted in southern China (ClinicalTrials.gov NCT01829334). Methods After obtaining ethical approval, healthy schoolchildren who had permanent first molars with occlusal fissures which were sound but deep or presented with only incipient caries were recruited for the study. Included molars were randomly allocated into one of four parallel study groups in units of left/right teeth per mouth. Two of the four groups adopted the methods of ART or fluoride-releasing resin sealant placement while the other two groups adopted the topical fluoride application methods. Fissure status of the molars in each group was evaluated every 6 months. Development of dentine caries and sealant retention over 24 months in the molars in the two sealant-using groups was compared in this report. Outcome on cost-effectiveness of all four groups over 36 months will be reported elsewhere. Results At baseline, a total of 280 children (383 molars) with mean age 7.8 years were involved for the two sealant groups. After 24 months, 261 children (357 molars) were followed. Proportions of molars with dentine caries were 7.3% and 3.9% in the ART sealant and fluoride-releasing resin sealant groups, respectively (chi-square test, p = 0.171). Life-table survival analysis showed that sealant retention (full and partial) rate over 24 months for the resin sealant (73%) was significantly higher than that (50%) for the ART sealant (p < 0.001). Molar survival (no development of dentine caries) rates in the ART sealant (93%) and fluoride-releasing resin sealant (96%) groups were not significantly different (p = 0.169). Multilevel logistic regression (GEE modeling) accounting for the effects of data clustering and confounding factors confirmed this finding. Conclusions Though the retention of fluoride-releasing resin sealant was better than that of the ART sealant, their effectiveness in preventing fissure caries in permanent molars did not differ significantly over 24 months. ART sealants could be a good alternative when and where resources for resin sealant placement are not readily available. PMID:24886444

Ion release and in vitro enamel fluoride uptake associated with pit and fissure sealants containing microencapsulated remineralizing agents.

PubMed

Burbank, Brant D; Cooper, Ryan L; Kava, Alyssa; Hartjes, Jennifer M; McHale, William A; Latta, Mark A; Gross, Stephen M

2017-04-01

To determine if pit-and-fissure sealants with microencapsulated remineralizing agents with sustained release of fluoride, calcium and phosphate ions could promote enamel fluoride uptake by demineralized tooth structure. Sealants that contained 5 w/w% microcapsules with aqueous solutions of 5M Ca(NO3)2 or 0.8M NaF or 6.0M K2HPO4 or a mixture of all three were prepared. Ion release profiles were measured as a function of time. Enamel fluoride uptake by demineralized tooth structure was determined. Sustained release of fluoride, calcium and phosphate ions from a sealant was demonstrated. Fluoride uptake by demineralized enamel was significantly increased compared to a control sealant manufactured without microcapsules (P< 0.01). Bovine enamel that contained 2.2±2.1 µg F/g of enamel prior to exposure to a sealant without microcapsules had 2.3±0.5 after 90 days. Enamel exposed to sealant with 5w/% NaF microcapsules went from 3.5±3.5 µg F/g of enamel prior to exposure to 148±76 after 90 days. Enamel exposed to sealant with 2 w/w% NaF, 2 w/w% Ca(NO3)2 and 1 w/w% K2HPO4 microcapsules went from 1.7±0.7 µg F/g of enamel prior to exposure to 190±137 after 90 days. Sealants with encapsulated remineralizing agents were capable of releasing biologically available fluoride, calcium, and phosphate ions. Incorporation of these microcapsules in pit and fissure sealants is a promising method for remineralization determined by enamel fluoride uptake measurements.

Inequalities in public water supply fluoridation in Brazil: An ecological study

PubMed Central

Gabardo, Marilisa CL; da Silva, Wander J; Olandoski, Marcia; Moysés, Simone T; Moysés, Samuel J

2008-01-01

Background The literature is scarce on the social and geographic inequalities in the access to and implementation of the fluoridation of public water supplies. This study adds knowledge to the Brazilian experience of the chronic privation of water and wastewater policies, access to potable water and fluoridation in the country. Thus, the aim of this study was to verify possible inequalities in the population's access to fluoridated drinking water in 246 Brazilian municipalities. Methods The information on the process of water fluoridation in the municipalities and in the macro region in which each municipality is located was obtained from the national epidemiological survey which was concluded in 2003. The data relating to the human development index at municipal level (HDI-M) and access to mains water came from the Brazilian Human Development Atlas, whilst the size of the population was obtained from a governmental source. The Fisher exact test (P < 0.05) was employed to identify significant associations between the explanatory variables and their ability to predict the principal outcomes of interest to this study, namely the presence or absence of the water fluoridation process in the municipalities as well as the length of time during which this measure has been implemented. Linear regression was used to observe the associations between the relevant variables in a multivariate environment. Results The results clearly showed that there is a relationship between municipalities with larger populations, located in more socio-economically advantaged regions and with better HDI-M, and where fluoridation is both present and has been implemented for a longer period of time (started before 1990). Conclusion The findings suggest that the aim of treating water with fluoride may not be being adequately achieved, requiring more effective strategies so that access to this measure can be expanded equitably. PMID:18402688

Is fluoride a risk factor for bone cancer? Small area analysis of osteosarcoma and Ewing sarcoma diagnosed among 0–49-year-olds in Great Britain, 1980–2005

PubMed Central

Blakey, Karen; Feltbower, Richard G; Parslow, Roger C; James, Peter W; Gómez Pozo, Basilio; Stiller, Charles; Vincent, Tim J; Norman, Paul; McKinney, Patricia A; Murphy, Michael F; Craft, Alan W; McNally, Richard JQ

2014-01-01

Background: Artificial fluoridation of drinking water to improve dental health has long been a topic of controversy. Opponents of this public health measure have cited the possibility of bone cancer induction. The study objective was to examine whether increased risk of primary bone cancer was associated with living in areas with higher concentrations of fluoride in drinking water. Methods: Case data on osteosarcoma and Ewing sarcoma, diagnosed at ages 0–49 years in Great Britain (GB) (defined here as England, Scotland and Wales) during the period 1980–2005, were obtained from population-based cancer registries. Data on fluoride levels in drinking water in England and Wales were accessed through regional water companies and the Drinking Water Inspectorate. Scottish Water provided data for Scotland. Negative binomial regression was used to examine the relationship between incidence rates and level of fluoride in drinking water at small area level. Results: The study analysed 2566 osteosarcoma and 1650 Ewing sarcoma cases. There was no evidence of an association between osteosarcoma risk and fluoride in drinking water [relative risk (RR) per one part per million increase in the level of fluoride = 1·001; 90% confidence interval (CI) 0·871, 1·151] and similarly there was no association for Ewing sarcoma (RR = 0·929; 90% CI 0·773, 1·115). Conclusions: The findings from this study provide no evidence that higher levels of fluoride (whether natural or artificial) in drinking water in GB lead to greater risk of either osteosarcoma or Ewing sarcoma. PMID:24425828

Copper-Mediated Fluorination of Arylboronate Esters. Identification of a Copper(III) Fluoride Complex

PubMed Central

Fier, Patrick S.; Luo, Jingwei; Hartwig, John F.

2013-01-01

A method for the direct conversion of arylboronate esters to aryl fluorides under mild conditions with readily available reagents is reported. Tandem reactions have also been developed for the fluorination of arenes and aryl bromides through aryl-boronate ester intermediates. Mechanistic studies suggest that this fluorination reaction occurs through facile oxidation of Cu(I) to Cu(III) followed by rate-limiting transmetallation of a bound arylboronate to Cu(III). Fast C-F reductive elimination is proposed to occur from an aryl-copper(III)-fluoride complex. Cu(III) intermediates have been generated independently and identified by NMR spectroscopy and ESI-MS. PMID:23384209

CONCENTRATION OF Pu USING AN IODATE PRECIPITATE

DOEpatents

Fries, B.A.

1960-02-23

A method is given for separating plutonium from lanthanum in a lanthanum fluoride carrier precipitation process for the recovery of plutonium values from an aqueous solution. The carrier precipitation process includes the steps of forming a lanthanum fluoride precipi- . tate, thereby carrying plutonium out of solution, metathesizing the fluoride precipitate to a hydroxide precipitate, and then dissolving the hydroxide precipitate in nitric acid. In accordance with the invention, the nitric acid solution, which contains plutonium and lanthanum, is made 0.05 to 0.15 molar in potassium iodate. thereby precipitating plutonium as plutonous iodate and the plutonous iodate is separated from the lanthanum- containing supernatant solution.

A randomised clinical evaluation of a fluoride mouthrinse and dentifrice in an in situ caries model.

PubMed

Parkinson, Charles R; Hara, Anderson T; Nehme, Marc; Lippert, Frank; Zero, Domenick T

2018-03-01

Fluoride mouthrinses provide advantages for fluoride delivery by maintaining elevated intra-oral fluoride concentrations following fluoride dentifrice use. This in situ caries study investigated potential anti-caries efficacy of a 220 ppm fluoride mouthrinse. This was an analyst-blinded, four-treatment, randomised, crossover study using partially demineralised, gauze-wrapped, human enamel samples mounted in a mandibular partial denture. Participants brushed twice daily for 14 days with either a 1150 ppm fluoride or a fluoride-free placebo dentifrice and either rinsed once daily with the 220 ppm fluoride mouthrinse or not. Following each treatment period, percent surface microhardness recovery (%SMHR) and enamel fluoride uptake (EFU) were assessed. Fifty three participants completed the study. Compared with the placebo dentifrice/no rinse treatment, the fluoride-containing regimens demonstrated greater enamel remineralisation (%SMHR) and fluoridation (EFU): fluoride dentifrice/fluoride rinse (%SMHR difference: 21.55 [95% CI: 15.78,27.32]; EFU difference 8.35 [7.21,9.29]); fluoride dentifrice/no rinse: 19.48 [13.81,25.15]; 6.47 [5.35,7.60]; placebo dentifrice/fluoride rinse: 16.76 [11.06,22.45]; 5.87 [4.72,7.00] (all P < .0001). There were no significant differences in%SMHR between fluoride regimens. The fluoride dentifrice/fluoride rinse regimen was associated with higher EFU than the fluoride dentifrice/no rinse (1.88 [0.75,3.01], P = .0013) and placebo dentifrice/fluoride rinse regimens (2.48 [1.34,3.62], P < .0001). Treatments were generally well-tolerated. The in situ caries model demonstrated that the fluoride mouthrinse is effective in promoting enamel caries lesion remineralisation and fluoridation whether used following a fluoride or non-fluoride dentifrice. Additive (potential) anti-caries benefits of a fluoride rinse after a fluoride dentifrice were confined to enhancements in lesion fluoridation (EFU). In conjunction with a fluoride dentifrice, fluoride mouthrinses enhance enamel fluoridation, which may be useful in caries prevention. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Hydrodistillation-adsorption method for the isolation of water-soluble, non-soluble and high volatile compounds from plant materials.

PubMed

Mastelić, J; Jerković, I; Blazević, I; Radonić, A; Krstulović, L

2008-08-15

Proposed method of hydrodistillation-adsorption (HDA) on activated carbon and hydrodistillation (HD) with solvent trap were compared for the isolation of water-soluble, non-soluble and high volatile compounds, such as acids, monoterpenes, isothiocyanates and others from carob (Certonia siliqua L.), rosemary (Rosmarinus officinalis L.) and rocket (Eruca sativa L.). Isolated volatiles were analyzed by GC and GC/MS. The main advantages of HDA method over ubiquitous HD method were higher yields of volatile compounds and their simultaneous separation in three fractions that enabled more detail analyses. This method is particularly suitable for the isolation and analysis of the plant volatiles with high amounts of water-soluble compounds. In distinction from previously published adsorption of remaining volatile compounds from distillation water on activated carbon, this method offers simultaneous hydrodistillation and adsorption in the same apparatus.

Contemporary biological markers of exposure to fluoride.

PubMed

Rugg-Gunn, Andrew John; Villa, Alberto Enrique; Buzalaf, Marília Rabelo Afonso

2011-01-01

Contemporary biological markers assess present, or very recent, exposure to fluoride: fluoride concentrations in blood, bone surface, saliva, milk, sweat and urine have been considered. A number of studies relating fluoride concentration in plasma to fluoride dose have been published, but at present there are insufficient data on plasma fluoride concentrations across various age groups to determine the 'usual' concentrations. Although bone contains 99% of the body burden of fluoride, attention has focused on the bone surface as a potential marker of contemporary fluoride exposure. From rather limited data, the ratio surface-to-interior concentration of fluoride may be preferred to whole bone fluoride concentration. Fluoride concentrations in the parotid and submandibular/sublingual ductal saliva follow the plasma fluoride concentration, although at a lower concentration. At present, there are insufficient data to establish a normal range of fluoride concentrations in ductal saliva as a basis for recommending saliva as a marker of fluoride exposure. Sweat and human milk are unsuitable as markers of fluoride exposure. A proportion of ingested fluoride is excreted in urine. Plots of daily urinary fluoride excretion against total daily fluoride intake suggest that daily urinary fluoride excretion is suitable for predicting fluoride intake for groups of people, but not for individuals. While fluoride concentrations in plasma, saliva and urine have some ability to predict fluoride exposure, present data are insufficient to recommend utilizing fluoride concentrations in these body fluids as biomarkers of contemporary fluoride exposure for individuals. Daily fluoride excretion in urine can be considered a useful biomarker of contemporary fluoride exposure for groups of people, and normal values have been published. Copyright © 2011 S. Karger AG, Basel.

Promoting social welfare through oral health: New Jersey's fluoridation experience.

PubMed

Mendoza, Roger Lee

2009-01-01

This study examines the contentious public health policy of treating community water with fluoride in the United States. The question for scholarly investigation is why water fluoridation has been unsuccessful in several parts of the United States relative to the rest. It addresses this question by looking into the processes of scientific discovery and information dissemination, benefits and risks of science-based health policy, related issues of provision and production, and spatial dimensions of policy development. The case method based on New Jersey's experience in public water fluoridation, was opted for this study. We find that policy debates, which are confined to single key issues, tend to breed binary choices and bipolar debates and result in policy stalemates. Consumer accessibility and desirability of merit goods thus become sharply conflicting social welfare values. They undermine the intent of science-based policies and often make alternative and second-best policies more practical to adopt.

TDDFT study on the sensing mechanism of a fluorescent sensor for fluoride anion: Inhibition of the ESPT process.

PubMed

Li, Guang-Yue; Liu, Dong; Zhang, Hang; Li, Wei-Wei; Wang, Feng; Liang, Ying-Hua

2015-01-01

The fluoride-sensing mechanism of a reported salicylaldehyde-based sensor (J. Photochem. Photobiol. B 2014, 138, 75) has been investigated by the TDDFT method. The present theoretical study indicates that there is an excited-state proton transfer (ESPT) process from the phenolic O-H moiety to the neighbor N atom in the sensor. The added fluoride anion could capture the proton in the O-H moiety and the corresponding phenolic anion is formed, which could inhibit the ESPT process. The experimental UV/Vis and fluorescence spectra are well reproduced by the calculated vertical excitation energies. Frontier molecular orbital analysis indicates that the local excited state of phenolic anion is responsible for its enhanced fluorescence. Due to this reason, the sensor can be used to sense fluoride anion by monitoring the fluorescent change. Copyright © 2015 Elsevier B.V. All rights reserved.

One-pot palladium-catalyzed synthesis of sulfonyl fluorides from aryl bromides† †Electronic supplementary information (ESI) available: Experimental details and supporting characterisation data. See DOI: 10.1039/c6sc03924c Click here for additional data file.

PubMed Central

Davies, Alyn T.; Curto, John M.

2017-01-01

A mild, efficient synthesis of sulfonyl fluorides from aryl and heteroaryl bromides utilizing palladium catalysis is described. The process involves the initial palladium-catalyzed sulfonylation of aryl bromides using DABSO as an SO2 source, followed by in situ treatment of the resultant sulfinate with the electrophilic fluorine source NFSI. This sequence represents the first general method for the sulfonylation of aryl bromides, and offers a practical, one-pot alternative to previously described syntheses of sulfonyl fluorides, allowing rapid access to these biologically important molecules. Excellent functional group tolerance is demonstrated, with the transformation successfully achieved on a number of active pharmaceutical ingredients, and their precursors. The preparation of peptide-derived sulfonyl fluorides is also demonstrated. PMID:28451264

Sub-ablative Er,Cr:YSGG laser irradiation under all-ceramic restorations: effects on demineralization and shear bond strength.

PubMed

Bağlar, Serdar

2018-01-01

This study evaluated the caries resistant effects of sub-ablative Er,Cr:YSGG laser irradiation alone and combined with fluoride in comparison with fluoride application alone on enamel prepared for veneer restorations. And also, evaluated these treatments' effects on the shear bond strength of all-ceramic veneer restorations. One hundred and thirty-five human maxillary central teeth were assigned to groups of 1a-control, 1b-laser treated, 1c-fluoride treated, 1d-laser + fluoride treated for shear bond testing and to groups of 2a-positive control(non-demineralised), 2b-laser treated, 2c-fluoride treated, 2d-laser + fluoride treated, 2e-negative control (demineralised) for microhardness testing (n = 15, N = 135). Demineralisation solutions of microhardness measurements were used for the ICP-OES elemental analysis. The parameters for laser irradiation were as follows: power output, 0.25 W; total energy density, 62.5 J/cm 2 and energy density per pulse, 4.48 J/cm 2 with an irradiation time of 20 s and with no water cooling. Five percent NaF varnish was used as fluoride preparate. ANOVA and Tukey HSD tests were performed (α = 5%). Surface treatments showed no significant effects on shear bond strength values (p = 0.579). However, significant differences were found in microhardness measurements and in elemental analysis of Ca and P amounts (p < 0.01). Surface-treated groups showed significantly high VNH values and significantly low ICP-OES values when compared with non-treated (-control) group while there were no significance among surface-treated groups regarding VHN and ICP-OES values. Sub-ablative Er,Cr:YSGG treatment alone or combined with fluoride is as an effective method as at least fluoride alone for preventing the prepared enamel to demineralization with no negative effect on shear bond strength.

Developmental Fluoride Neurotoxicity: A Systematic Review and Meta-Analysis

PubMed Central

Sun, Guifan; Zhang, Ying; Grandjean, Philippe

2012-01-01

Background: Although fluoride may cause neurotoxicity in animal models and acute fluoride poisoning causes neurotoxicity in adults, very little is known of its effects on children’s neurodevelopment. Objective: We performed a systematic review and meta-analysis of published studies to investigate the effects of increased fluoride exposure and delayed neurobehavioral development. Methods: We searched the MEDLINE, EMBASE, Water Resources Abstracts, and TOXNET databases through 2011 for eligible studies. We also searched the China National Knowledge Infrastructure (CNKI) database, because many studies on fluoride neurotoxicity have been published in Chinese journals only. In total, we identified 27 eligible epidemiological studies with high and reference exposures, end points of IQ scores, or related cognitive function measures with means and variances for the two exposure groups. Using random-effects models, we estimated the standardized mean difference between exposed and reference groups across all studies. We conducted sensitivity analyses restricted to studies using the same outcome assessment and having drinking-water fluoride as the only exposure. We performed the Cochran test for heterogeneity between studies, Begg’s funnel plot, and Egger test to assess publication bias, and conducted meta-regressions to explore sources of variation in mean differences among the studies. Results: The standardized weighted mean difference in IQ score between exposed and reference populations was –0.45 (95% confidence interval: –0.56, –0.35) using a random-effects model. Thus, children in high-fluoride areas had significantly lower IQ scores than those who lived in low-fluoride areas. Subgroup and sensitivity analyses also indicated inverse associations, although the substantial heterogeneity did not appear to decrease. Conclusions: The results support the possibility of an adverse effect of high fluoride exposure on children’s neurodevelopment. Future research should include detailed individual-level information on prenatal exposure, neurobehavioral performance, and covariates for adjustment. PMID:22820538

Assessing the stock market volatility for different sectors in Malaysia by using standard deviation and EWMA methods

NASA Astrophysics Data System (ADS)

Saad, Shakila; Ahmad, Noryati; Jaffar, Maheran Mohd

2017-11-01

Nowadays, the study on volatility concept especially in stock market has gained so much attention from a group of people engaged in financial and economic sectors. The applications of volatility concept in financial economics can be seen in valuation of option pricing, estimation of financial derivatives, hedging the investment risk and etc. There are various ways to measure the volatility value. However for this study, two methods are used; the simple standard deviation and Exponentially Weighted Moving Average (EWMA). The focus of this study is to measure the volatility on three different sectors of business in Malaysia, called primary, secondary and tertiary by using both methods. The daily and annual volatilities of different business sector based on stock prices for the period of 1 January 2014 to December 2014 have been calculated in this study. Result shows that different patterns of the closing stock prices and return give different volatility values when calculating using simple method and EWMA method.

Determination of selected anions in water by ion chromatography

USGS Publications Warehouse

Fishman, Marvin J.; Pyen, Grace

1979-01-01

Ion chromatography is a rapid, sensitive, precise, and accurate method for the determination of major anions in rain water and surface waters. Simultaneous analyses of a single sample for bromide, chloride, fluoride, nitrate, nitrite, orthophosphate, and sulfate require approximately 20 minutes to obtain a chromatogram.Minimum detection limits range from 0.01 milligrams per liter for fluoride to 0.20 milligrams per liter for chloride and sulfate. Percent relative standard deviations were less than nine percent for all anions except nitrite in Standard Reference Water Samples. Only one reference sample contained nitrite and its concentration was near the minimum level of detection. Similar precision was found for chloride, nitrate, and sulfate at concentrations less than 5 milligrams per liter in rainfall samples. Precision for fluoride ranged from 12 to 22 percent, but is attributed to the low concentrations in these samples. The other anions were not detected.To determine accuracy of results, several samples were spiked with known concentrations of fluoride, chloride, nitrate, and sulfate; recoveries ranged from 96 to 103 percent. Known amounts of bromide and phosphate were added, separately, to several other waters, which contained bromide or phosphate. Recovery of added bromide and phosphate ranged from approximately 95 to 104 percent. No recovery data were obtained for nitrite.Chloride, nitrate, nitrite, orthophosphate, and sulfate, in several samples, were also determined independently by automated colorimetric procedures. An automated ion-selective electrode method was used to determine fluoride. Results are in agreement with results obtained by ion chromatography.

Efficient fluoride removal using Al-Cu oxide nanoparticles supported on steel slag industrial waste solid.

PubMed

Blanco-Flores, Alien; Arteaga-Larios, Nubia; Pérez-García, Víctor; Martínez-Gutiérrez, José; Ojeda-Escamilla, María; Rodríguez-Torres, Israel

2018-03-01

A SSW/Al-Cu formed from an industrial solid waste and Al-Cu Nps are utilized for the removal of fluoride from aqueous solutions. The SSW/Al-Cu was obtained by a chemical reduction method. The SSW/Al-Cu was characterized by TEM, SEM, FT-IR, XRD, BET, and pH zpc techniques. The Nps were formed as bimetallic oxides and deposited in the form of spheroidal particles forming agglomerations. The sizes of these particles range from 1 to 3 nm. The surface area and average pore width of SSW/Al-Cu were 2.99 m 2 /g and 17.09 nm, respectively. The adsorption kinetics were better described using the second-order model, pointing to chemical adsorption with an equilibrium time of 540 min. The thermodynamic parameters obtained here confirm the spontaneous and endothermic nature of the process. The percentage of fluoride removal was 89.5% using the four-bladed disk turbine, and computational fluid dynamics (CFD) modeling demonstrated that using the four-bladed disk turbine helped improve the fluoride removal process. The maximum adsorption capacity was 3.99 mg/g. The Langmuir-Freundlich model best describes the adsorption process, which occurred by a combination of mechanisms, such as electrostatic interactions between the ions involved in the process. This study proves that the chemical modification of this waste solid created an efficient bimetallic nanomaterial for fluoride removal. Furthermore, the method of preparation of these nanocomposites is quite scalable.

Magnesium fluoride recovery method

DOEpatents

Gay, Richard L.; McKenzie, Donald E.

1989-01-01

A method of obtaining magnesium fluoride substantially free from radioactive uranium from a slag containing the same and having a radioactivity level of at least about 7000 pCi/gm. The slag is ground to a particle size of about 200 microns or less. The ground slag is contacted with an acid under certain prescribed conditions to produce a liquid product and a particulate solid product. The particulate solid product is separated from the liquid and treated at least two more times with acid to produce a solid residue consisting essentially of magnesium fluoride substantially free of uranium and having a residual radioactivity level of less than about 1000 pCi/gm. In accordance with a particularly preferred embodiment of the invention a catalyst and an oxidizing agent are used during the acid treatment and preferably the acid is sulfuric acid having a strength of about 1.0 Normal.

Fluoride mechanisms.

PubMed

ten Cate, J M; van Loveren, C

1999-10-01

This article discusses fluoride mechanisms in relation to dental caries. The authors specifically address firmly bound versus loosely bound fluoride; different fluoride active ingredients; fluoride and demineralization and remineralization; fluoride slow-release devices and F-releasing dental materials; antimicrobial effects of fluoride; the uptake of fluoride by oral bacteria; inhibition of enolase, protein-intruding ATPase and sugar transport; the various aspects of plaque as it relates to fluoride; and the rational use of fluoride.

Defluoridation by Bacteriogenic Iron Oxides: Sorption Studies

NASA Astrophysics Data System (ADS)

Evans, K.; Ferris, F.

2009-05-01

At concentrations above 1 mg/L, fluoride in drinking water can lead to dental and skeletal fluorosis, a disease that causes mottling of the teeth, calcification of ligaments, crippling bone deformities and many other physiological disorders that can, ultimately, lead to death. Conservative estimates are that fluorosis afflicts tens of millions of people worldwide. As there is no treatment for fluorosis, prevention is the only means of controlling the disease. While numerous defluoridation techniques have been explored, no single method has been found to be both effective and inexpensive enough to implement widely. Our research began in India, with a large-scale geochemical study of the groundwater in a fluoride-contaminated region of Orissa. Having developed a better understanding of the geochemical relationships that exist between fluoride and other parameters present in an affected area, as well as the complex relationships that arise among those parameters that can impact the presence of fluoride, we began investigating certain remediation scenarios involving iron oxides. A common approach to remediation involves the partitioning of fluoride from groundwater by sorption onto a variety of materials, one of the most effective of which is iron oxide whose surface area acts as a scavenger for fluoride. In the presence of iron oxidizing bacteria, the oxidation rate of iron has been shown to be ˜6 times greater than in their absence; fluoride should, therefore, be removed from an aqueous environment by bacteriogenic iron oxides (BIOS) much more quickly than by abiotic iron oxides. Most recently, sorption studies have been conducted using both BIOS and synthetic hydrous ferric oxides in order to compare the behavior between biotic and abiotic sorbents. These studies have provided sorption isotherms that allow comparison of fluoride removed by sorption to BIOS versus synthetic iron oxides. Sorption affinity constants have also been determined, which allow for the prediction of fluoride removal in a wide variety of groundwater systems. Sorption isotherms and affinity constants show the use of BIOS to be a promising technique for the remediation of fluoride in groundwater.

Fluorine--a current literature review. An NRC and ATSDR based review of safety standards for exposure to fluorine and fluorides.

PubMed

Prystupa, Jeff

2011-02-01

A review of the literature of the element fluorine and its bonded-form, fluoride, was undertaken. Generally regarded as safe, an expanding body of literature reveals that fluoride's toxicity has been unappreciated, un-scrutinized, and hidden for over 70 years. The context for the literature search and review was an environmental climate-change study, which demonstrated widespread fluoride contamination by smokestack emissions from coal-fired electricity-generating plants. The objective of this review is to educate and inform regarding the ubiquitous presence and harmful nature of this now ever-present corrosive and reactive toxin. Methods include examination of national health agency reviews, primarily the National Research Council (NRC), Agency for Toxic Substances & Disease Registry (ATSDR), standard medical toxicology references, text books, as well as reports and documents from both private and public research as well as consumer-based NGOs. Study criteria were chosen for relevancy to the subject of the toxicity of fluoride. Fluoride is the extreme electron scavenger, the most corrosive of all elements, as well as the most-reactive. Fluoride appears to attack living tissues, via several mechanisms. Fluoride renders strong evidence that it is a non-biological chemical, demonstrating no observed beneficial function or role in organic chemistry, beyond use as a pesticide or insecticide. Fluorine has a strong role to play in industry, having been utilized extensively in metals, plastics, paints, aluminium, steel, and uranium production. Due to its insatiable appetite for calcium, fluorine and fluorides likely represent a form of chemistry that is incompatible with biological tissues and organ system functions. Based on an analysis of the affects of fluoride demonstrated consistently in the literature, safe levels have not been determined nor standardized. Mounting evidence presents conflicting value to its presence in biological settings and applications. Evidence examined in this review of the literature, and specifically the recent report by the National Research Council (NRC), offer strong support for an immediate reconsideration concerning risk vs benefit. Consensus recommendations from several sources are presented.

Comparative diagnostic value of 18F-fluoride PET-CT versus MRI for skull-base bone invasion in nasopharyngeal carcinoma.

PubMed

Le, Yali; Chen, Yu; Zhou, Fan; Liu, Guangfu; Huang, Zhanwen; Chen, Yue

2016-10-01

This study compared the diagnostic value of F-fluoride PET-computed tomography (PET-CT) and MRI in skull-base bone erosion in nasopharyngeal carcinoma (NPC) patients. A total of 93 patients with biopsy-confirmed NPC were enrolled, including 68 men and 25 women between 23 and 74 years of age. All patients were evaluated by both F-fluoride PET-CT and MRI, and the interval between the two imaging examinations was less than 20 days. The patients received no treatment either before or between scans. The studies were interpreted by two nuclear medicine physicians or two radiologists with more than 10 years of professional experience who were blinded to both the diagnosis and the results of the other imaging studies. The reference standard was skull-base bone erosion at a 20-week follow-up imaging study. On the basis of the results of the follow-up imaging studies, 52 patients showed skull-base bone erosion. The numbers of true positives, false positives, true negatives, and false negatives with F-fluoride PET-CT were 49, 4, 37, and 3, respectively. The numbers of true positives, false positives, true negatives, and false negatives with MRI were 46, 5, 36, and 6, respectively. The sensitivity, specificity, and crude accuracy of F-fluoride PET-CT were 94.23, 90.24, and 92.47%, respectively; for MRI, these values were 88.46, 87.80, and 88.17%. Of the 52 patients, 43 showed positive findings both on F-fluoride PET-CT and on MRI. Within the patient cohort, F-fluoride PET-CT and MRI detected 178 and 135 bone lesions, respectively. Both F-fluoride PET-CT and MRI have high sensitivity, specificity, and crude accuracy for detecting skull-base bone invasion in patients with NPC. F-fluoride PET-CT detected more lesions than did MRI in the skull-base bone. This suggests that F-fluoride PET-CT has a certain advantage in evaluating the skull-base bone of NPC patients. Combining the two methods could improve the diagnostic accuracy of skull-base bone invasion for NPC.

Fluxing agent for metal cast joining

DOEpatents

Gunkel, Ronald W.; Podey, Larry L.; Meyer, Thomas N.

2002-11-05

A method of joining an aluminum cast member to an aluminum component. The method includes the steps of coating a surface of an aluminum component with flux comprising cesium fluoride, placing the flux coated component in a mold, filling the mold with molten aluminum alloy, and allowing the molten aluminum alloy to solidify thereby joining a cast member to the aluminum component. The flux preferably includes aluminum fluoride and alumina. A particularly preferred flux includes about 60 wt. % CsF, about 30 wt. % AlF.sub.3, and about 10 wt. % Al.sub.2 O.sub.3.

Ferroelectric fluoride compositions and methods of making and using same

DOEpatents

Halasyamani, P Shiv; Chang, Hong-Young

2015-04-07

A method for synthesis of a ferroelectric material characterized by the general formula A.sub.xB.sub.yF.sub.z where A is an alkaline earth metal, B is transition metal or a main group metal, x and y each range from about 1 to about 5, and z ranges from about 1 to about 20 comprising contacting an alkaline earth metal fluoride, a difluorometal compound and a fluoroorganic acid in a medium to form a reaction mixture; and subjecting the reaction mixture to conditions suitable for hydrothermal crystal growth.

No-carrier-added (NCA) aryl ([sup 18]F) fluorides via the nucleophilic aromatic substitution of electron rich aromatic rings

DOEpatents

Yushin Ding; Fowler, J.S.; Wolf, A.P.

1993-10-19

A method for synthesizing no-carrier-added (NCA) aryl [.sup.18 F] fluoride substituted aromatic aldehyde compositions bearing an electron donating group is described. The method of the present invention includes the step of reacting aromatic nitro aldehydes having a suitably protected hydroxyl substitutent on an electron rich ring. The reaction is The U.S. Government has rights in this invention pursuant to Contract Number DE-AC02-76CH00016, between the U.S. Department of Energy and Associated Universities Inc.

No-carrier-added (NCA) aryl (18E) fluorides via the nucleophilic aromatic substitution of electron rich aromatic rings

DOEpatents

Ding, Yu-Shin; Fowler, Joanna S.; Wolf, Alfred P.

1993-01-01

A method for synthesizing no-carrier-added (NCA) aryl [.sup.18 F] fluoride substituted aromatic aldehyde compositions bearing an electron donating group is described. The method of the present invention includes the step of reacting aromatic nitro aldehydes having a suitably protected hydroxyl substitutent on an electron rich ring. The reaction is The U.S. Government has rights in this invention pursuant to Contract Number DE-AC02-76CH00016, between the U.S. Department of Energy and Associated Universities Inc.

Estimation and prediction under local volatility jump-diffusion model

NASA Astrophysics Data System (ADS)

Kim, Namhyoung; Lee, Younhee

2018-02-01

Volatility is an important factor in operating a company and managing risk. In the portfolio optimization and risk hedging using the option, the value of the option is evaluated using the volatility model. Various attempts have been made to predict option value. Recent studies have shown that stochastic volatility models and jump-diffusion models reflect stock price movements accurately. However, these models have practical limitations. Combining them with the local volatility model, which is widely used among practitioners, may lead to better performance. In this study, we propose a more effective and efficient method of estimating option prices by combining the local volatility model with the jump-diffusion model and apply it using both artificial and actual market data to evaluate its performance. The calibration process for estimating the jump parameters and local volatility surfaces is divided into three stages. We apply the local volatility model, stochastic volatility model, and local volatility jump-diffusion model estimated by the proposed method to KOSPI 200 index option pricing. The proposed method displays good estimation and prediction performance.

40 CFR 63.606 - Performance tests and compliance provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... P2O5 feed rate, metric ton/hr (ton/hr). K = conversion factor, 1000 mg/g (453,600 mg/lb). (2) Method... fluorides, g/metric ton (lb/ton) of equivalent P2O5 feed. Csi = concentration of total fluorides from... Where: Mp = total mass flow rate of phosphorus-bearing feed, metric ton/hr (ton/hr). Rp = P2O5 content...

40 CFR 63.606 - Performance tests and compliance provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... P2O5 feed rate, metric ton/hr (ton/hr). K = conversion factor, 1000 mg/g (453,600 mg/lb). (2) Method... fluorides, g/metric ton (lb/ton) of equivalent P2O5 feed. Csi = concentration of total fluorides from... Where: Mp = total mass flow rate of phosphorus-bearing feed, metric ton/hr (ton/hr). Rp = P2O5 content...

40 CFR 63.606 - Performance tests and compliance provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... P2O5 feed rate, metric ton/hr (ton/hr). K = conversion factor, 1000 mg/g (453,600 mg/lb). (2) Method... fluorides, g/metric ton (lb/ton) of equivalent P2O5 feed. Csi = concentration of total fluorides from... Where: Mp = total mass flow rate of phosphorus-bearing feed, metric ton/hr (ton/hr). Rp = P2O5 content...

Combined chemical and optical methods for monitoring the early decay stages of surrogate human models.

PubMed

Statheropoulos, M; Agapiou, A; Zorba, E; Mikedi, K; Karma, S; Pallis, G C; Eliopoulos, C; Spiliopoulou, C

2011-07-15

As the body decays shortly after death, a variety of gases and volatile organic compounds (VOCs) constantly emanate. Ethical and practical reasons limit the use of human corpses in controlled, time-dependent, intervening experiments for monitoring the chemistry of body decay. Therefore the utilization of pig carcasses serves as a potential surrogate to human models. The aim of this work was to study buried body decay in conditions of entrapment in collapsed buildings. Six domestic pigs were used to study carcass decay. They were enclosed in plastic body bags after being partially buried with rubbles, resembling entrapment in collapsed buildings. Three experimental cycles were performed, employing two pig carcasses in each cycle; VOCs and inorganic gases were measured daily, along with daily visible and thermal images. VOCs were collected in standard sorbent tubes and subsequently analyzed using a Thermal Desorption/Gas Chromatograph/high sensitivity bench-top Time-of-Flight Mass Spectrometer (TD/GC/TOF-MS). A comprehensive, stage by stage, detailed information on the decay process is being presented based on the experimental macroscopic observations, justifying thus the use of pig carcasses as surrogate material. A variety of VOCs were identified including almost all chemical classes: sulfur, nitrogen, oxygen compounds (aldehydes, alcohols, ketones, acids and esters), hydrocarbons, fluorides and chlorides. Carcasses obtained from a pig farm resulted in more sulfur and nitrogen cadaveric volatiles. Carbon dioxide was by far the most abundant inorganic gas identified along with carbon monoxide, hydrogen sulfide and sulfur dioxide. Visual monitoring was based on video captured images allowing for macroscopic observations, while thermal camera monitoring which is mostly temperature dependent, resulted in highlighting the local micro-changes on the carcasses, as a result of the intense microbial activity. The combination of chemical and optical methods proved very useful and informative, uncovering hidden aspects of the early stages of decay and also guiding in the development of combined chemical and imaging methods for the detection of dead bodies. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Removal of uranium from aqueous HF solutions

DOEpatents

Pulley, Howard; Seltzer, Steven F.

1980-01-01

This invention is a simple and effective method for removing uranium from aqueous HF solutions containing trace quantities of the same. The method comprises contacting the solution with particulate calcium fluoride to form uranium-bearing particulates, permitting the particulates to settle, and separting the solution from the settled particulates. The CaF.sub.2 is selected to have a nitrogen surface area in a selected range and is employed in an amount providing a calcium fluoride/uranium weight ratio in a selected range. As applied to dilute HF solutions containing 120 ppm uranium, the method removes at least 92% of the uranium, without introducing contaminants to the product solution.

Divalent fluoride doped cerium fluoride scintillator

DOEpatents

Anderson, David F.; Sparrow, Robert W.

1991-01-01

The use of divalent fluoride dopants in scintillator materials comprising cerium fluoride is disclosed. The preferred divalent fluoride dopants are calcium fluoride, strontium fluoride, and barium fluoride. The preferred amount of divalent fluoride dopant is less than about two percent by weight of the total scintillator. Cerium fluoride scintillator crystals grown with the addition of a divalent fluoride have exhibited better transmissions and higher light outputs than crystals grown without the addition of such dopants. These scintillators are useful in radiation detection and monitoring applications, and are particularly well suited for high-rate applications such as positron emission tomography (PET).

Effects of long-term repeated topical fluoride applications and adhesion promoter on shear bond strengths of orthodontic brackets

PubMed Central

Endo, Toshiya; Ishida, Rieko; Komatsuzaki, Akira; Sanpei, Shinya; Tanaka, Satoshi; Sekimoto, Tsuneo

2014-01-01

Objective: The purpose of this study was to assess the effects of long-term repeated topical application of fluoride before bonding and an adhesion promoter on the bond strength of orthodontic brackets. Materials and Methods: A total of 76 bovine incisors were collected and divided equally into four groups. In group 1, the brackets were bonded without topical fluoride application or adhesion promoter. In group 2, before bonding, the adhesion promoter was applied to nonfluoridated enamel. In group 3, the brackets were bonded without the application of the adhesion promoter to enamel, which had undergone long-term repeated topical fluoride treatments. Teeth in group 4 received the long-term repeated topical applications of fluoride, and the brackets were bonded using the adhesion promoter. All the brackets were bonded using BeautyOrtho Bond self-etching adhesive. The shear bond strength was measured and the bond failure modes were evaluated with the use of the adhesive remnant index (ARI) after debonding. Results: The mean shear bond strength was significantly lower in group 3 than in groups 1, 2, and 4, and there were no significant differences between the groups except for group 3. There were significant differences in the distribution of ARI scores between groups 2 and 3, and between groups 3 and 4. Conclusions: The adhesion promoter can recover the bond strength reduced by the long-term repeated topical applications of fluoride to the prefluoridation level and had a significantly great amount of adhesives left on either fluoridated or nonfluoridated enamel. PMID:25512720

Neglected health literacy undermining fluorosis control efforts: A pilot study among schoolchildren in an endemic village of rural Rajasthan, India

PubMed Central

Rustagi, Neeti; Rathore, Ajey Singh; Meena, Jitendra Kumar; Chugh, Ankita; Pal, Ranabir

2017-01-01

Background: Ingestion of excess fluoride can cause fluorosis which adversely affects teeth and bones. Fluorosis is a major public health problem in the state of Rajasthan with all its 32 districts having variable fluoride contamination, and many initiatives are currently implemented in this region to mitigate the fluorosis burden. Objective: The objective of this study was to assess fluorosis, its risk factors, and the awareness among school students and teachers in endemic villages of Jodhpur district, Rajasthan. Materials and Methods: A representative sample of 300 students of age 12–15 years were enrolled for cross-sectional study in selected villages. Data were collected regarding awareness, behavioral and preventive practices about fluorosis and clinical assessment and fluoride estimation in water and urine samples was done. Results: Dental fluorosis through Dean's index was observed in 24.5% of students. The awareness and practices for fluorosis prevention and its risk factors were poor among both students and teachers. Intake of piped water supply was reported by majority of students (95.8%). High fluoride concentration was found in 35 (81.3%) out of 43 urine samples. Conclusion: Improvement in drinking water supply in the endemic village of Rajasthan has decreased the burden of fluorosis, but low level of awareness and prevailing dietary and behavioral practices still pose them at risk of high fluoride intake. This signifies the need to address nonconventional sources of fluoride intake (diet and toothpaste) and early screening of disease by involving teachers and family physicians in fluoride mitigation efforts. PMID:29417003

[Anticaries effectiveness of fluoride toothpaste: a meta-analysis].

PubMed

Chaves, Sônia Cristina Lima; Vieira-da-Silva, Lígia Maria

2002-10-01

To carry out a meta-analysis on the effectiveness of fluoride toothpaste for reducing dental caries to calculate the effect size of different hypothesis. MEDLINE and LILACS databases were studied in the period from 1980 to 1998. To evaluate the quality of the studies, methodological rigor criteria proposed by Kay & Locker (1996) were applied after the criteria were submitted to an expert committee of CNPq (National Scientific Council of Brazil) senior researchers. Of 43 papers selected, 22 met the proposed criteria. The effect size of intervention was calculated from differences among the groups and the overall effect of five groups of hypothesis. The high concentration of fluoride in the toothpaste is associated with a larger effect (overall effect = -0.17 CI 95% -0.22/-0.12). The largest caries reductions were observed when comparing fluoride toothpastes and no fluoride toothpastes (overall effect = -0.29 IC 95% -0.34/-0.24). The addiction of antimicrobial agents (overall effect = -0.03 IC 95% -0.07/+0.02), differences in abrasive systems (overall effect = -0.02 IC 95% -0.09/+0.04) and active components do not increase the effectiveness of fluoride toothpastes (overall effect = -0.04 IC 95% -0.10/+0.01). The highest caries reductions were seen in studies where there was supervised tooth brushing. This review reinforced the importance of tooth brushing with fluoride toothpastes for controlling dental caries. However it showed the emphasis put on medical approaches for disease control rather than specific educational actions. The heterogeneity of the results shows the need to consider issues such as the scenario for implementing preventive methods in the evaluation process.

Cytotoxic effects of glass ionomer cements on human dental pulp stem cells correlate with fluoride release.

PubMed

Kanjevac, Tatjana; Milovanovic, Marija; Volarevic, Vladislav; Lukic, Miodrag L; Arsenijevic, Nebojsa; Markovic, Dejan; Zdravkovic, Nebojsa; Tesic, Zivoslav; Lukic, Aleksandra

2012-01-01

Glass ionomer cements (GICs) are commonly used as restorative materials. Responses to GICs differ among cell types and it is therefore of importance to thoroughly investigate the influence of these restorative materials on pulp stem cells that are potential source for dental tissue regeneration. Eight biomaterials were tested: Fuji I, Fuji II, Fuji VIII, Fuji IX, Fuji Plus, Fuji Triage, Vitrebond and Composit. We compared their cytotoxic activity on human dental pulp stem cells (DPSC) and correlated this activity with the content of Fluoride, Aluminium and Strontium ions in their eluates. Elution samples of biomaterials were prepared in sterile tissue culture medium and the medium was tested for toxicity by an assay of cell survival/proliferation (MTT test) and apoptosis (Annexin V FITC Detection Kit). Concentrations of Fluoride, Aluminium and Strontium ions were tested by appropriate methods in the same eluates. Cell survival ranged between 79.62% (Fuji Triage) to 1.5% (Fuji Plus) and most dead DPSCs were in the stage of late apoptosis. Fluoride release correlated with cytotoxicity of GICs, while Aluminium and Strontium ions, present in significant amount in eluates of tested GICs did not. Fuji Plus, Vitrebond and Fuji VIII, which released fluoride in higher quantities than other GICs, were highly toxic to human DPSCs. Opposite, low levels of released fluoride correlated to low cytotoxic effect of Composit, Fuji I and Fuji Triage.

Estimated dietary fluoride intake for New Zealanders.

PubMed

Cressey, Peter; Gaw, Sally; Love, John

2010-01-01

Existing fluoride concentration and consumption data were used to estimate fluoride intakes from the diet and toothpaste use, for New Zealand subpopulations, to identify any population groups at risk of high-fluoride intake. For each sub-population, two separate dietary intake estimates were made--one based on a non-fluoridated water supply (fluoride concentration of 0.1 mg/L), and the other based on a water supply fluoridated to a concentration of 1.0 mg/L. Fluoride concentration data were taken from historical surveys, while food consumption data were taken from national 24-hour dietary recall surveys or from simulated diets. Mean and 95th percentile estimations of dietary fluoride intake were well below the upper level of intake (UL), whether intakes were calculated on the basis of a non-fluoridated or fluoridated water supply. The use of fluoride-containing toothpastes provides additional fluoride intake. For many of the population groups considered, mean fluoride intakes were below the adequate intake (AI) level for caries protection, even after inclusion of the fluoride contribution from toothpaste. Intake of fluoride was driven by consumption of dietary staples (bread, potatoes),beverages (particularly tea, soft drinks, and beer), and the fluoride status of drinking water. Estimates of fluoride intake from the diet and toothpaste did not identify any groups at risk of exceeding the UL, with the exception of infants (6-12 months) living in areas with fluoridated water supplies and using high-fluoride toothpaste. In contrast, much of the adult population may be receiving insufficient fluoride for optimum caries protection from these sources, as represented by the AI.

PROCESS OF PREPARING A FLUORIDE OF TETRAVLENT URANIUM

DOEpatents

Wheelwright, E.J.

1959-02-17

A method is described for producing a fluoride salt pf tetravalent uranium suitable for bomb reduction to metallic uranium. An aqueous solution of uranyl nitrate is treated with acetic acid and a nitrite-suppressor and then contacted with metallic lead whereby uranium is reduced from the hexavalent to the tetravalent state and soluble lead acetate is formed. Sulfate ions are then added to the solution to precipitate and remove the lead values. Hydrofluoric acid and alkali metal ions are then added causing the formation of an alkali metal uranium double-fluoride in which the uranium is in the tetravalent state. After recovery, this precipitate is suitable for using in the limited production of metallic uranium.

Nonvolatile, semivolatile, or volatile: redefining volatile for volatile organic compounds.

PubMed

Võ, Uyên-Uyén T; Morris, Michael P

2014-06-01

Although widely used in air quality regulatory frameworks, the term "volatile organic compound" (VOC) is poorly defined. Numerous standardized tests are currently used in regulations to determine VOC content (and thus volatility), but in many cases the tests do not agree with each other, nor do they always accurately represent actual evaporation rates under ambient conditions. The parameters (time, temperature, reference material, column polarity, etc.) used in the definitions and the associated test methods were created without a significant evaluation of volatilization characteristics in real world settings. Not only do these differences lead to varying VOC content results, but occasionally they conflict with one another. An ambient evaporation study of selected compounds and a few formulated products was conducted and the results were compared to several current VOC test methodologies: SCAQMD Method 313 (M313), ASTM Standard Test Method E 1868-10 (E1868), and US. EPA Reference Method 24 (M24). The ambient evaporation study showed a definite distinction between nonvolatile, semivolatile, and volatile compounds. Some low vapor pressure (LVP) solvents, currently considered exempt as VOCs by some methods, volatilize at ambient conditions nearly as rapidly as the traditional high-volatility solvents they are meant to replace. Conversely, bio-based and heavy hydrocarbons did not readily volatilize, though they often are calculated as VOCs in some traditional test methods. The study suggests that regulatory standards should be reevaluated to more accurately reflect real-world emission from the use of VOC containing products. The definition of VOC in current test methods may lead to regulations that exclude otherwise viable alternatives or allow substitutions of chemicals that may limit the environmental benefits sought in the regulation. A study was conducted to examine volatility of several compounds and a few formulated products under several current VOC test methodologies and ambient evaporation. This paper provides ample evidence to warrant a reevaluation of regulatory standards and provides a framework for progressive developments based on reasonable and scientifically justifiable definitions of VOCs.

Metabolism of 2-chloro-1,1-difluoroethene to glyoxylic and glycolic acid in rat hepatic microsomes.

PubMed

Baker, M T; Vasquez, M T; Bates, J N; Chiang, C K

1990-01-01

The complete metabolic fate of the volatile anesthetic halothane is unclear since 2-chloro-1,1-diflurorethene (CDE), a reductive halothane metabolite, is known to readily release inorganic fluoride upon oxidation by cytochrome P-450. This study sought to clarify the metabolism of CDE by determining its metabolites and the roles of induce cytochrome P-450 forms in its metabolism. Upon incubation of [14C]CDE with rat hepatic microsomes, two major radioactive products were found which accounted for greater than 94% of the total metabolites. These compounds were determined to be the nonhalogenated compounds, glyoxylic and glycolic acids, which were formed in a ratio of approximately 1 to 2 of glyoxylic to glycolic acid. No other radioactive metabolites could be detected. Following incubation of CDE with hepatic microsomes isolated from rats treated with cytochrome P-450 inducers, measurement of fluoride release showed that phenobarbital induced CDE metabolism to the greatest degree at high CDE levels, isoniazid was the most effective inducer at low CDE concentrations, and beta-naphthoflavone was ineffective as an inducer. These results suggest that CDE biotransformation primarily involves the generation of an epoxide intermediate, which undergoes mechanisms of decay leading to total dehalogenation of the molecule, and that this metabolism is preferentially carried out by the phenobarbital- and ethanol-inducible forms of cytochrome P-450.

Water Fluoridation and the Association of Sugar-Sweetened Beverage Consumption and Dental Caries in Australian Children

PubMed Central

Spencer, A. John; Roberts-Thomson, Kaye F.; Plastow, Katrina

2013-01-01

Objectives. We examined demographic and socioeconomic differences in the consumption of sugar-sweetened beverages (SSBs), its association with dental caries in children, and whether exposure to water fluoridation modifies this association. Methods. In a cross-sectional study, we used a stratified, clustered sampling design to obtain information on 16 508 children aged 5 to 16 years enrolled in Australian school dental services in 2002 to 2005. Dental staff assessed dental caries, and parents completed a questionnaire about their child’s residential history, sources of drinking water, toothbrushing frequency, socioeconomic status (SES), and SSB consumption. Results. Children who brushed their teeth less often and were older, male, of low SES, from rural or remote areas consumed significantly more SSBs. Caries was significantly associated with greater SSB consumption after controlling for potential confounders. Finally, greater exposure to fluoridated water significantly reduced the association between children’s SSB consumption and dental caries. Conclusions. Consumption of SSBs should be considered a major risk factor for dental caries. However, increased exposure to fluoridated public water helped ameliorate the association between SSB consumption and dental decay. These results reconfirm the benefits of community water fluoridation for oral health. PMID:23327241

Prevalence of dental caries and fluoride concentration of drinking water: A systematic review

PubMed Central

Goodarzi, Fatemeh; Mahvi, Amir Hossein; Hosseini, Mostafa; Nodehi, Ramin Nabizadeh; Kharazifard, Mohammad Javad; Parvizishad, Mina

2017-01-01

Background: The objective of this study was to systematically review prevalence of dental caries at different water fluoride levels and emphasize fluoride concentration of drinking water and prevalence of dental caries. Materials and Methods: A comprehensive study was conducted using PubMed database. Inclusion criteria were predefined and some articles fulfilled these criteria. Study validity was assessed by some checklists. Surveys were conducted to determine prevalence of dental caries among individuals. Results: The heterogeneity in the group of children with deciduous teeth in terms of the amount of fluoride in drinking water and social class was significant, and the results of the studies in all the subgroups could not be pooled. However, the heterogeneity of group 2 for subjects with permanent teeth in terms of the fluoride level in drinking water and social class was not significant, and the results of the studies in each subgroup could be pooled together. Conclusion: The meta-regression showed that tooth type and social class had a significant association with the difference in the prevalence of dental caries. Therefore, these variables were the sources of heterogeneity, and the studies must be grouped and subgrouped based on these variables. PMID:28702056

A Theoretical Study of Structural, Electronic and Vibrational Properties of Small Fluoride Clusters

NASA Astrophysics Data System (ADS)

Waters, Kevin; Pandey, Ratnesh; Nigam, Sandeep; He, Haiying; Pingle, Subhash; Pandey, Avinash; Pandey, Ravindra

2014-03-01

Alkaline earth metal fluorides are an interesting family of ionic crystals having a wide range of applications in solid state lasers, luminescence, scintillators, to name just a few. In this work, small stoichiometric clusters of (MF2)n (M = Mg, Ca Sr, Ba, n =1-6) were studied for structural, vibrational and electronic properties using first-principles methods based on density functional theory. A clear trend of structural and electronic structure evolution was found for all the alkaline earth metal fluorides when the cluster size n increases from 1 to 6. Our study reveals that these fluoride clusters mimic the bulk-like behavior at the very small size. Among the four series of metal fluorides, however, (MgF2)n clusters stands out to be different in its preference of equilibrium structures owing to the much smaller ionic radius of Mg and the higher degree of covalency in the Mg-F bonding. The calculated binding energy, highest stretching frequency, ionization potential, and HOMO-LUMO gap decrease from MgF2 to BaF2 for the same cluster size. These variations are explained in terms of the change in the ionic radius and the basicity of the metal ions.

Approximation methods of European option pricing in multiscale stochastic volatility model

NASA Astrophysics Data System (ADS)

Ni, Ying; Canhanga, Betuel; Malyarenko, Anatoliy; Silvestrov, Sergei

2017-01-01

In the classical Black-Scholes model for financial option pricing, the asset price follows a geometric Brownian motion with constant volatility. Empirical findings such as volatility smile/skew, fat-tailed asset return distributions have suggested that the constant volatility assumption might not be realistic. A general stochastic volatility model, e.g. Heston model, GARCH model and SABR volatility model, in which the variance/volatility itself follows typically a mean-reverting stochastic process, has shown to be superior in terms of capturing the empirical facts. However in order to capture more features of the volatility smile a two-factor, of double Heston type, stochastic volatility model is more useful as shown in Christoffersen, Heston and Jacobs [12]. We consider one modified form of such two-factor volatility models in which the volatility has multiscale mean-reversion rates. Our model contains two mean-reverting volatility processes with a fast and a slow reverting rate respectively. We consider the European option pricing problem under one type of the multiscale stochastic volatility model where the two volatility processes act as independent factors in the asset price process. The novelty in this paper is an approximating analytical solution using asymptotic expansion method which extends the authors earlier research in Canhanga et al. [5, 6]. In addition we propose a numerical approximating solution using Monte-Carlo simulation. For completeness and for comparison we also implement the semi-analytical solution by Chiarella and Ziveyi [11] using method of characteristics, Fourier and bivariate Laplace transforms.

Oral fluoride retention after use of fluoride dentifrices.

PubMed

Duckworth, R M; Morgan, S N

1991-01-01

Fluoride is the only extensively clinically proven means of reducing dental caries. Despite a large body of epidemiological data on the effectiveness of fluoride, delivered in the form of dentifrices, mouthrinses, drinking water, etc., the precise mode of action of fluoride is not completely understood. The purpose of this paper is to report an investigation of the link between oral fluoride levels and applied fluoride dose from dentifrices. Human salivary fluoride clearance studies and equilibrium baseline studies of fluoride in saliva and plaque have been carried out with dentifrices which contained 1,000, 1,500 and 2,500 micrograms fluoride per gram as sodium monofluorophosphate. After a single brushing with a fluoride dentifrice, salivary fluoride decreased in two distinct phases: an initial rapid phase which lasted for 40-80 min, depending on the individual, and a second slow phase lasting for several hours. The latter phase is believed to be due to fluoride released from an oral fluoride reservoir. During regular repeated use of the test dentifrices, the equilibrium baseline fluoride concentration, attained in both saliva and plaque between one application and the next, increased significantly compared with placebo values. Such elevated baseline fluoride concentrations also increased with increasing Na2FPO3 content of the dentifrices. The present work supports the concept that labile fluoride, stored in an oral fluoride reservoir at the time of treatment application, may maintain a prolonged protective effect against dental caries.

Calibration of equipment for analysis of drinking water fluoride: a comparison study.

PubMed

Quock, Ryan L; Chan, Jarvis T

2012-03-01

Current American Dental Association evidence-based recommendations for prescription of dietary fluoride supplements are based in part on the fluoride concentration of a pediatric patient's drinking water. With these recommendations in mind, this study compared the relative accuracy of fluoride concentration analysis when a common apparatus is calibrated with different combinations of standard values. Fluoride solutions in increments of 0.1 ppm, from a range of 0.1 to 1.0 ppm fluoride, as well as 2.0 and 4.0 ppm, were gravimetrically prepared and fluoride concentration measured in pentad, using a fluoride ion-specific electrode and millivolt meter. Fluoride concentrations of these solutions were recorded after calibration with the following 3 different combinations of standard fluoride solutions: 0.1 ppm and 0.5 ppm, 0.1 ppm and 1.0 ppm, 0.5 ppm and 1.0 ppm. Statistical analysis showed significant differences in the fluoride content of water samples obtained with different two-standard fluoride solutions. Among the two-standard fluoride solutions tested, using 0.5 ppm and 1.0 ppm as two-standard fluoride solutions provided the most accurate fluoride measurement of water samples containing fluoride in the range of 0.1 ppm to 4.0 ppm. This information should be valuable to dental clinics or laboratories in fluoride analysis of drinking water samples.

Assessment of antifungal activity of herbal and conventional toothpastes against clinical isolates of Candida albicans.

PubMed

Adwan, Ghaleb; Salameh, Yousef; Adwan, Kamel; Barakat, Ali

2012-05-01

To detect the anticandidal activity of nine toothpastes containing sodium fluoride, sodium monofluorophosphate and herbal extracts as an active ingredients against 45 oral and non oral Candida albicans (C. albicans) isolates. The antifungal activity of these toothpaste formulations was determined using a standard agar well diffusion method. Statistical analysis was performed using a statistical package, SPSS windows version 15, by applying mean values using one-way ANOVA with post-hoc least square differences (LSD) method. A P value of less than 0.05 was considered significant. All toothpastes studied in our experiments were effective in inhibiting the growth of all C. albicans isolates. The highest anticandidal activity was obtained from toothpaste that containing both herbal extracts and sodium fluoride as active ingredients, while the lowest activity was obtained from toothpaste containing sodium monofluorophosphate as an active ingredient. Antifungal activity of Parodontax toothpaste showed a significant difference (P< 0.001) against C. albicans isolates compared to toothpastes containing sodium fluoride or herbal products. In the present study, it has been demonstrated that toothpaste containing both herbal extracts and sodium fluoride as active ingredients are more effective in control of C. albicans, while toothpaste that containing monofluorophosphate as an active ingredient is less effective against C. albicans. Some herbal toothpaste formulations studied in our experiments, appear to be equally effective as the fluoride dental formulations and it can be used as an alternative to conventional formulations for individuals who have an interest in naturally-based products. Our results may provide invaluable information for dental professionals.

METHOD OF IMPROVING CORROSION RESISTANCE OF ZIRCONIUM

DOEpatents

Shannon, D.W.

1961-03-28

An improved intermediate rinse for zirconium counteracts an anomalous deposit that often results in crevices and outof-the-way places when ordinary water is used to rinse away a strong fluoride etching solution designed to promote passivation of the metal. The intermediate rinse, which is used after the etching solution and before the water, is characterized by a complexing agent for fluoride ions such as aluminum or zirconium nitrates or chlorides.

Method of making carbide/fluoride/silver composites

NASA Technical Reports Server (NTRS)

Sliney, Harold E. (Inventor); Dellacorte, Christopher (Inventor)

1991-01-01

A composition containing 30 to 70 percent chromium carbide, 5 to 20 percent soft noble metal, 5 to 20 percent metal fluorides, and 20 to 60 percent metal binder is used in a powdered metallurgy process for the production of self-lubricating components, such as bearings. The use of the material allows the self-lubricating bearing to maintain its low friction properties over an extended range of operating temperatures.

METHOD OF PREPARING PLUTONIUM TETRAFLUORIDE

DOEpatents

Beede, R.L.; Hopkins, H.H. Jr.

1959-11-17

C rystalline plutonium tetrafluoride is precipitated from aqueous up to 1.6 N mineral acid solutions of a plutorium (IV) salt with fluosilicic acid anions, preferably at room temperature. Hydrogen fluoride naay be added after precipitation to convert any plutonium fluosilicate to the tetrafluoride and any silica to fluosilicic acid. This process results in a purer product, especially as to iron and aluminum, than does the precipitation by the addition of hydrogen fluoride.

QLF monitoring of therapies for early secondary caries arrestment and remineralization

NASA Astrophysics Data System (ADS)

Fontana, Margherita; Gonzalez-Cabezas, Carlos; Stookey, George K.

2000-03-01

Secondary caries (SC) is the most common reason for restoration failure. The purpose of this study was to evaluate the Quantitative Light-Induced Fluorescence (QLF) method for monitoring therapies to inhibit SC progression. Forty-eight human teeth with resin restorations were demineralized for 4 days in a microbial caries model. Half of each specimen was then covered with an acid-resistant varnish to maintain the baseline lesion, and treated (group 1: non-treated control; group 2: chlorhexidine varnish for 24 h; group 3: fluoride varnish for 24 h; group 4: APF topical fluoride gel for 4 min), prior to being demineralized for 4 more days. Specimens were analyzed by QLF, sectioned, stained with Rhodamine B, and analyzed with a confocal microscope (CLSM) for lesion depth. The QLF results indicated that the control group was significantly (p less than 0.05) different (i.e., lesions progressed) from groups treated with fluoride (groups 3 and 4; lesions remineralized). All other group comparisons were not significantly different. Results obtained from CLSM analysis were similar to the ones obtained with QLF, except that lesions in group 2 were significantly deeper than the ones in the fluoride groups. Results suggest that the QLF method has a clear potential for monitoring remineralizing therapies for SC.

Characterization of the volatile profiles of beer using headspace solid-phase microextraction and gas chromatography-mass spectrometry.

PubMed

Rossi, Serena; Sileoni, Valeria; Perretti, Giuseppe; Marconi, Ombretta

2014-03-30

The objective of this study was a multivariate characterization of the volatile profile of beers. Such a characterization is timely considering the increasing worldwide consumption of beer, the continuous growth of microbreweries and the importance of volatile compounds to beer flavour. A method employing solid-phase microextraction and gas chromatography-mass spectrometry (SPME-GC-MS) was optimized and then applied to a sample set of 36 industrial and craft beers of various styles and fermentation types. The volatile profiles of different beer styles is described, with particular attention paid to the volatile compounds characteristic of a spontaneously fermented lambic raspberry framboise beer. Furthermore, it was also possible to identify which specific volatile compounds are principally responsible for the differences in the volatile profiles of top- and bottom-fermented beers. Moreover, a volatile fingerprint of the craft top-fermented Italian beers was defined, as they show a very similar volatile profile. Finally, the volatile compounds that are characteristic of the bock-style beers are described. The SPME-GC-MS analytical method optimized in this study is suitable for characterizing the volatile fingerprint of different beers, especially on the basis of the kind of fermentation (top, bottom or spontaneous), the method of production and the style of the beer. © 2013 Society of Chemical Industry.

Urinary fluoride excretion in preschool children after intake of fluoridated milk and use of fluoride-containing toothpaste.

PubMed

Norman, M; Twetman, S; Hultgren Talvilahti, A; Granström, E; Stecksén-Blicks, C

2017-03-01

To assess the urinary fluoride excretion in preschool children after drinking fluoridated milk with 0.185 mg F and 0.375 mg F and to study the impact of use of fluoride toothpaste. Double-blind cross-over study. Nine healthy children, 2.5-4.5 years of age. In a randomized order, participants drank 1.5 dl milk once daily for 7 days with no fluoride added (control), 0.185 mg fluoride added and 0.375 mg fluoride added. The experiment was performed twice with (Part I) and without (Part II) parental tooth brushing with 1,000 ppm fluoride toothpaste. The fluoride content in the piped drinking water was 0.5 mg F/L. Urinary fluoride excretion. The 24-hour urinary fl uoride excretion/kg body weight varied from 0.014 mg F for the placebo intervention and non-fluoride toothpaste to 0.027 mg F for the 0.375 mg intervention with use of 1,000 ppm fluoride toothpaste. The difference compared with the placebo intervention was not statistically significant for any of the interventions when fluoride toothpaste was used (p⟩0.05) while it was statistically significantly different when non-fluoride toothpaste was used (p⟨0.05). All sources of fluoride must be considered when designing community programs. With 0.5 mg F/L in the drinking water and daily use of fluoride toothpaste, most children had a fluoride intake optimal for dental health. In this setting, additional intake of fluoride milk was within safe limits up to 0.185 mg/day while conclusions about the safety of 0.375 mg/day were uncertain. Copyright© 2017 Dennis Barber Ltd

Determining the optimal fluoride concentration in drinking water for fluoride endemic regions in South India.

PubMed

Viswanathan, Gopalan; Jaswanth, A; Gopalakrishnan, S; Siva Ilango, S; Aditya, G

2009-10-01

Fluoride ion in drinking water is known for both beneficial and detrimental effects on health. The prevalence of fluorosis is mainly due to the intake of large quantities of fluoride through drinking water owing to more than 90% bioavailability. The objective of this study is to predict optimal fluoride level in drinking water for fluoride endemic regions by comprising the levels of fluoride and other water quality parameters in drinking water, prevalence of fluorosis, fluoride intake through water, food and beverages such as tea and coffee and also considering the progressive accumulation of fluoride in animal bones, by comparing with non fluoride endemic areas comprise of the same geological features with the aid of regression analysis. Result of this study shows that increase of fluoride level above 1.33 mg/l in drinking water increases the community fluorosis index (CFI) value more than 0.6, an optimum index value above which fluorosis is considered to be a public health problem. Regression plot between water fluoride and bone fluoride levels indicates that, every increase of 0.5mg/l unit of water fluoride level increases the bone fluoride level of 52 mg/kg unit within 2 to 3 years. Furthermore, the consumption of drinking water containing more than 0.65 mg/l of fluoride can raise the total fluoride intake per day more than 4 mg, which is the optimum fluoride dose level recommended for adults by the Agency for Toxic Substances and Disease Registry. From the result, the people in fluoride endemic areas in South India are advised to consume drinking water with fluoride level within the limit of 0.5 to 0.65 mg/l to avoid further fluorosis risk.

Comparison and evaluation of volatile oils from three different extraction methods for some Thai fragrant flowers.

PubMed

Paibon, W; Yimnoi, C-A; Tembab, N; Boonlue, W; Jampachaisri, K; Nuengchamnong, N; Waranuch, N; Ingkaninan, K

2011-04-01

Several tropical flowers have distinctive fragrances which are very appealing to use in perfumery, cosmetics and spa. However, to obtain a 'natural fragrance' from the flower is a challenge as the scent could change during the extraction process. The aim of the study is to find the suitable procedure for extraction of volatile oils from some Thai fragrant flowers. Three different methods: hydrodistillation, solvent extraction and enfleurage methods have been applied for the extraction of volatile oil from Jasminum sambac L. Aiton; Oleaceae (jasmine). The quantities and quality of jasmine volatile oils obtained from the different tested methods were compared. The solvent extraction method using 95% ethanol provided the greatest level of oil yield. However, sensory evaluation using preference test showed that the scents of the volatile oils from solvent extraction using diethyl ether and from enfleurage method were the closest to the fresh flowers compared with the volatile oils obtained from other methods. Their chemical constituents were analysed using gas chromatography coupled with mass spectrometer. Both volatile oils were then evaluated using a triangle discrimination test. From the triangle test, we found that 14 panellists from the total of 36 could not distinguish between the scents of jasmine oil from enfleurage and fresh jasmine flowers whereas only one panellist could not distinguish between the scent of jasmine oil from the solvent extraction and fresh jasmine flowers. These results suggest that the scent of the volatile oil obtained from the enfleurage method was the closest to fresh flowers compared with that obtained from other methods. This method was then successfully applied for extraction of volatile oils from three other Thai fragrant flowers, Michelia alba DC.; Magnoliaceae, Millingtonia hortensis L.; Bignoniaceae and Hedychium coronarium J. Konig; Zingiberaceae. © 2010 The Authors. Journal compilation © 2010 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

[The dose-effect relationship of water fluoride levels and renal damage in children].

PubMed

Liu, Jun-Ling; Xia, Tao; Yu, Yao-Yong; Sun, Xian-Zhong; Zhu, Qilong; He, Weihong; Zhang, Ming; Wang, Aiguo

2005-05-01

To explore the dose-effect relationship of water fluoride levels and renal damage in children and observe the difference of renal function between high-loaded fluoride people and dental fluorosis people in the same water fluoride level region. 210 children were divided into seven groups in term of drinking water fluoride levels and whether they suffered from dental fluorosis. Fluoride concentrations in urine and serum and activities of urine NAG and gamma-GT were determined. The urine and serum fluoride of high-loaded fluoride people and dental fluorosis people increased compared with control, moreover fluoride contents in urine and serum increased gradually with the increase of fluoride level in drinking water. Urine NAG and gamma-GT activities significantly increased in dental fluorosis people from area of 2.58 mg/L fluoride in drinking water and in those two groups from area of 4.51 mg/L fluoride in drinking water. Moreover, there existed an obvious dose-effect relationship between the drinking water fluoride concentration and NAG and gamma-GT activity. Over 2.0 mg/L fluoride in drinking water can cause renal damage in children, and the damage degree increases with the drinking water fluoride content. Renal damage degree is not related to whether the children suffered from dental fluorosis and mainly due to water fluoride concentration.

Pore Structure and Fluoride Ion Adsorption Characteristics of Zr (IV) Surface-Immobilized Resin Prepared Using Polystyrene as a Porogen

NASA Astrophysics Data System (ADS)

Mizuki, Hidenobu; Ito, Yudai; Harada, Hisashi; Uezu, Kazuya

Zr(IV) surface-immobilized resins for removal of fluoride ion were prepared by surface template polymerization using polystyrene as a porogen. At polymerization, polystyrene was added in order to increase mesopores (2-50 nm) and macropore (>50 nm) with large macropores (around 300 nm) formed with internal aqueous phase of W⁄O emulsion. The pore structure of Zr(IV) surface-immobilized resins was evaluated by measuring specific surface area, pore volume, and pore size distribution with volumetric adsorption measurement instrument and mercury porosimeter. The adsorption isotherms were well fitted by Langmuir equation. The removal of fluoride was also carried out with column method. Zr(IV) surface-immobilized resins, using 10 g⁄L polystyrene in toluene at polymerization, possessed higher volume of not only mesopores and macropores but also large macropores. Furethermore, by adding the polystyrene with smaller molecular size, the pore volume of mesopores, macropores and large macropores was significantly increased, and the fluoride ion adsorption capacity and the column utilization also increased.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Sungho, E-mail: shochoi@krict.re.kr; Park, Byung-Yoon; Jung, Ha-Kyun

Highlights: {yields} Systematic study of the fluorides doped solution-processed ZnO thin films via the luminescence and electrical behaviors. {yields} Defect-related visible emission bands are affected by annealing ambient and fluoride addition. {yields} Adding lithium fluoride followed by annealing in oxygen ambient leads to a controlled defect density with proper TFT performance. -- Abstract: To develop an efficient channel layer for thin film transistors (TFTs), understanding the defect-related luminescence and electrical property is crucial for solution-processed ZnO thin films. Film growth with the fluorides addition, especially using LiF, followed by the oxygen ambient post-annealing leads to decreased defect-related emission as wellmore » as enhanced switching property. The saturation mobility and current on/off ratio are 0.31 cm{sup 2} V{sup -1} s{sup -1} and 1.04 x 10{sup 3}. Consequently, we can visualize an optimized process condition and characterization method for solution-processed TFT based on the fluorine-doped ZnO film channel layer by considering the overall emission behavior.« less

Oxidative aliphatic C-H fluorination with manganese catalysts and fluoride ion

PubMed Central

Liu, Wei; Huang, Xiongyi; Groves, John T

2014-01-01

Fluorination is a reaction that is useful in improving the chemical stability and changing the binding affinity of biologically active compounds. The protocol described here can be used to replace aliphatic, C(sp3)-H hydrogen in small molecules with fluorine. Notably, isolated methylene groups and unactivated benzylic sites are accessible. The method uses readily available manganese porphyrin and manganese salen catalysts and various fluoride ion reagents, including silver fluoride (AgF), tetrabutylammonium fluoride and triethylamine trihydrofluoride (TREAT·HF), as the source of fluorine. Typically, the reactions afford 50–70% yield of mono-fluorinated products in one step. Two representative examples, the fragrance component celestolide and the nonsteroidal anti-inflammatory drug ibuprofen, are described; they produced useful isolated quantities (250–300 mg, ~50% yield) of fluorinated material over periods of 1–8 h. The procedures are performed in a typical fume hood using ordinary laboratory glassware. No special precautions to rigorously exclude water are required. PMID:24177292

Magnesium fluoride reduction-vessel liners. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Latham-Brown, C.E.

1986-03-26

The work described in this report details a program that demonstrated a method by which magnesium fluoride, the by-product of the reduction reaction of uranium tetrafluoride to uranium metal could be used to replace the present graphite used to line the reduction vessel. Utilization of magnesium fluoride (MgF2) as a reduction-vessel liner has the potential to decrease carbon contamination and thereby reduce DU derby rejects due to chemistry. Additionally, there would be the elimination of the cost of the graphite crucible liner and the associated disposal costs by replacement with the by-product of the reduction reaction, which is magnesium fluoride.more » The process would ultimately result in reduced manufacturing costs for derby metal and higher yield of finished penetrators. This was to be accomplished in such a manner as to produce uranium metal derbies which would be accommodated into the present Nuclear Metals-Carolina Metals penetrator production process with minimal changes in equipment and procedures.« less

Prenatal Fluoride Exposure and Cognitive Outcomes in Children at 4 and 6–12 Years of Age in Mexico

PubMed Central

Thomas, Deena; Hu, Howard; Angeles Martinez-Mier, E.; Sanchez, Brisa N.; Basu, Niladri; Peterson, Karen E.; Ettinger, Adrienne S.; Wright, Robert; Zhang, Zhenzhen; Liu, Yun; Schnaas, Lourdes; Mercado-García, Adriana; María Téllez-Rojo, Martha; Hernández-Avila, Mauricio

2017-01-01

Background: Some evidence suggests that fluoride may be neurotoxic to children. Few of the epidemiologic studies have been longitudinal, had individual measures of fluoride exposure, addressed the impact of prenatal exposures or involved more than 100 participants. Objective: Our aim was to estimate the association of prenatal exposure to fluoride with offspring neurocognitive development. Methods: We studied participants from the Early Life Exposures in Mexico to Environmental Toxicants (ELEMENT) project. An ion-selective electrode technique was used to measure fluoride in archived urine samples taken from mothers during pregnancy and from their children when 6–12 y old, adjusted for urinary creatinine and specific gravity, respectively. Child intelligence was measured by the General Cognitive Index (GCI) of the McCarthy Scales of Children’s Abilities at age 4 and full scale intelligence quotient (IQ) from the Wechsler Abbreviated Scale of Intelligence (WASI) at age 6–12. Results: We had complete data on 299 mother–child pairs, of whom 287 and 211 had data for the GCI and IQ analyses, respectively. Mean (SD) values for urinary fluoride in all of the mothers (n=299) and children with available urine samples (n=211) were 0.90 (0.35) mg/L and 0.82 (0.38) mg/L, respectively. In multivariate models we found that an increase in maternal urine fluoride of 0.5mg/L (approximately the IQR) predicted 3.15 (95% CI: −5.42, −0.87) and 2.50 (95% CI −4.12, −0.59) lower offspring GCI and IQ scores, respectively. Conclusions: In this study, higher prenatal fluoride exposure, in the general range of exposures reported for other general population samples of pregnant women and nonpregnant adults, was associated with lower scores on tests of cognitive function in the offspring at age 4 and 6–12 y. https://doi.org/10.1289/EHP655 PMID:28937959

IMPACT OF FLUORIDE ON DENTAL HEALTH QUALITY.

PubMed

Medjedovic, Eida; Medjedovic, Senad; Deljo, Dervis; Sukalo, Aziz

2015-12-01

Fluoride is natural element that strengthens teeth and prevents their decay. Experts believe that the best way to prevent cavities is the use of fluoride from multiple sources. Studies even show that in some cases, fluoride can stop already started damage of the teeth. In children younger than 6 years fluoride is incorporated into the enamel of permanent teeth, making the teeth more resistant to the action of bacterial and acids in food. The aim of this study is to determine the effects of improving the health status of teeth after six months treatment with the use of topical fluoridation 0.5% NaF, and the level and quality of the impact of treatment with chemical 0.5% NaF on the dental health of children at age from 8 to 15 years, in relation to gender and chronological age. This study included school children aged 8 to 15 years who visited health and dental services dependent in Mostar. It is obvious that after the implementation of treatment with 5% NaF by the method of topical fluoridation, health status of subjects from the experimental group significantly improved, so that at the final review 89.71% or 61 subjects of the experimental group had healthy (cured teeth), tooth with dental caries only 5.88% or 4 respondents tooth with dental caries and filling 4.41% or 3 respondents, extracted baby tooth 14.71% or 10 respondents, while for 13.24% of respondents was identified state with still unerupted teeth. Our findings are indirectly confirmed that the six-month treatment of fluoridation with 5% NaF, contributed to statistically significant improvement in overall oral health of the experimental group compared to the control group which was not treated by any dental treatment. It can be concluded that there is a statistically significant difference in the evaluated parameters of oral health of children in the control group compared to the studied parameters of oral health the experimental group of children at the final dental examination.

Bone formation in ankylosing spondylitis during anti-tumour necrosis factor therapy imaged by 18F-fluoride positron emission tomography

PubMed Central

Bruijnen, Stefan T G; Verweij, Nicki J F; van Duivenvoorde, Leonie M; Bravenboer, Nathalie; Baeten, Dominique L P; van Denderen, Christiaan J; van der Horst-Bruinsma, Irene E; Voskuyl, Alexandre E; Custers, Martijn; van de Ven, Peter M; Bot, Joost C J; Boden, Bouke J H; Lammertsma, Adriaan A; Hoekstra, Otto S H; Raijmakers, Pieter G H M; van der Laken, Conny J

2018-01-01

Abstract Objectives Excessive bone formation is an important hallmark of AS. Recently it has been demonstrated that axial bony lesions in AS patients can be visualized using 18F-fluoride PET-CT. The aim of this study was to assess whether 18F-fluoride uptake in clinically active AS patients is related to focal bone formation in spine biopsies and is sensitive to change during anti-TNF treatment. Methods Twelve anti-TNF-naïve AS patients [female 7/12; age 39 years (SD 11); BASDAI 5.5 ± 1.1] were included. 18 F-fluoride PET-CT scans were performed at baseline and in two patients, biopsies were obtained from PET-positive and PET-negative spine lesions. The remaining 10 patients underwent a second 18F-fluoride PET-CT scan after 12 weeks of anti-TNF treatment. PET scans were scored visually by two blinded expert readers. In addition, 18F-fluoride uptake was quantified using the standardized uptake value corrected for individual integrated whole blood activity concentration (SUVAUC). Clinical response to anti-TNF was defined according to a ⩾ 20% improvement in Assessment of SpondyloArthritis international Society criteria at 24 weeks. Results At baseline, all patients showed at least one axial PET-positive lesion. Histological analysis of PET-positive lesions in the spine confirmed local osteoid formation. PET-positive lesions were found in the costovertebral joints (43%), facet joints (23%), bridging syndesmophytes (20%) and non-bridging vertebral lesions (14%) and in SI joints (75%). After 12 weeks of anti-TNF treatment, 18F-fluoride uptake in clinical responders decreased significantly in the costovertebral (mean SUVAUC −1.0; P < 0.001) and SI joints (mean SUVAUC −1.2; P = 0.03) in contrast to non-responders. Conclusions 18F-fluoride PET-CT identified bone formation, confirmed by histology, in the spine and SI joints of AS patients and demonstrated alterations in bone formation during anti-TNF treatment. PMID:29329443

Caries and fluoridated water in two Brazilian municipalities with low prevalence of the disease

PubMed Central

da Cruz, Mariângela Guanaes Bortolo; Narvai, Paulo Capel

2018-01-01

ABSTRACT OBJECTIVE To analyze the association between exposure to fluoridated water and dental caries in a context of widespread use of fluoride toothpaste in Brazil, in a scenario of low prevalence of the disease. METHODS This is a cross-sectional observational study, of the census type, in the form of a double population-based epidemiological survey carried out in two municipalities of the state of São Paulo in 2014. The sample consisted of adolescents aged 11 and 12 years, exposed (n = 184) or not exposed (n = 128) to fluoridated water for at least five years. The populations studied lived in communities of the same geographic region and had small demographic size and similar socioeconomic classification, differing only in the exposure (Silveiras) or not exposure (São José do Barreiro) to fluoridated water. The experience, magnitude, and degree of polarization of dental caries in these populations were analyzed using the DMFT and SiC indexes, and the association was tested using Pearson’s chi-square statistics and prevalence ratio between those not exposed and those exposed to fluoridated water. RESULTS Although caries experience (DMFT ≥ 1) was not associated with exposure to fluoridated water (chi-square = 1.78; p = 0.18; α = 5%), a significant difference was observed in the magnitude with which the disease reached the population: the means of DMFT were 1.76 in those exposed and 2.60 in those not exposed and the means of SiC were 4.04 and 6.16, respectively. The degree of polarization, indicated by the percentage of subjects with DMFT = 0, was different, being it higher (41.8%) in subjects exposed and lower (34.3%) in subjects not exposed. The prevalence ratio between those not exposed and those exposed was 1.13, indicating little expressiveness in prevalence difference. CONCLUSIONS Exposure to fluoridated water implied lower mean values for the DMFT and SiC indexes, even in the presence of the concomitant exposure to fluoridated toothpaste, in a scenario of low prevalence of the disease, and with a similar pattern of caries distribution in the populations analyzed. PMID:29641653

Urinary Fluoride Concentration in Children with Disabilities Following Long-Term Fluoride Tablet Ingestion

ERIC Educational Resources Information Center

Liu, Hsiu-Yueh; Chen, Jung-Ren; Hung, Hsin-Chia; Hsiao, Szu-Yu; Huang, Shun-Te; Chen, Hong-Sen

2011-01-01

Urine is the most commonly utilized biomarker for fluoride excretion in public health and epidemiological studies. Approximately 30-50% of fluoride is excreted from urine in children. Urinary fluoride excretion reflects the total fluoride intake from multiple sources. After administering fluoride tablets to children with disabilities, urinary…

[Study on two preparation methods for beta-CD inclusion compound of four traditional Chinese medicine volatile oils].

PubMed

Li, Hailiang; Cui, Xiaoli; Tong, Yan; Gong, Muxin

2012-04-01

To compare inclusion effects and process conditions of two preparation methods-colloid mill and saturated solution-for beta-CD inclusion compound of four traditional Chinese medicine volatile oils and study the relationship between each process condition and volatile oil physical properties and the regularity of selective inclusion of volatile oil components. Volatile oils from Nardostachyos Radix et Rhizoma, Amomi Fructus, Zingiberis Rhizoma and Angelicaesinensis Radix were prepared using two methods in the orthogonal test. These inclusion compounds by optimized processes were assessed and compared by such methods as TLC, IR and scanning electron microscope. Inclusion oils were extracted by steam distillation, and the components found before and after inclusion were analyzed by GC-MS. Analysis showed that new inclusion compounds, but inclusion compounds prepared by the two processes had differences to some extent. The colloid mill method showed a better inclusion effect than the saturated solution method, indicating that their process conditions had relations with volatile oil physical properties. There were differences in the inclusion selectivity of components between each other. The colloid mill method for inclusion preparation is more suitable for industrial requirements. To prepare volatile oil inclusion compounds with heavy gravity and high refractive index, the colloid mill method needs longer time and more water, while the saturated solution method requires higher temperature and more beta-cyclodextrin. The inclusion complex prepared with the colloid mill method contains extended molecular weight chemical composition, but the kinds of components are reduced.

Kinetics of fluoride bioavailability in supernatant saliva and salivary sediment.

PubMed

Naumova, E A; Sandulescu, T; Bochnig, C; Gaengler, P; Zimmer, S; Arnold, W H

2012-07-01

The assessment of the fluoride kinetics in whole saliva as well as in the different salivary phases (supernatant saliva and sediment) is essential for the understanding of fluoride bioavailability. To assess the fluoride content, provided by sodium fluoride and amine fluoride, in the supernatant saliva and in salivary sediment. Seven trained volunteers were randomly attributed to 2 groups in a cross-over design and brushed their teeth in the morning for 3 min with a product containing either sodium fluoride or amine fluoride. Saliva was collected before, immediately after tooth brushing and 30, 120, and 360 min later and measured. The samples were centrifuged 10 min at 3024 × g. Fluoride content of the supernatant saliva and of the sediment was analysed using a fluoride sensitive electrode. All subjects repeated the study cycles 2 times, and statistical analyses were made using the nonparametric sign test for related samples, the Wilcoxon-Mann-Whitney-test for independent samples. There was a significant increase in fluoride immediately after tooth brushing in both groups in saliva and sediment. The distribution of fluoride between salivary sediment and supernatant saliva (ratio) varied considerably at the different collection times: decreased from 17.87 in baseline samples of saliva to 0.07 immediately and to 0.86 half an hour after tooth brushing in the sodium fluoride group and from 14.33 to 2.85 and to 3.09 in the amine fluoride group. Furthermore after 120 min and after 360 min after tooth brushing the ratio increased from 17.6 to 31.6 in the sodium fluoride group and from 20.5 to 25.76 in the amine fluoride group. No difference was found in the sediment-supernatant saliva ratio between the sodium fluoride and the amine fluoride groups 360 min after tooth brushing. For the assessment of fluoride kinetics in whole saliva it is necessary to pay attention to at least four factors: fluoride formulation, time after fluoride application, fluoride concentration in supernatant saliva and fluoride concentration in salivary sediment. This study was approved by the Ethical Committee of the University of Witten/Herdecke permission 21/2008. Copyright © 2012 Elsevier Ltd. All rights reserved.

Application of response surface methodology for optimization of biosorption of fluoride from groundwater using Shorea robusta flower petal

NASA Astrophysics Data System (ADS)

Biswas, G.; Kumari, M.; Adhikari, K.; Dutta, S.

2017-12-01

Fluoride pollution in groundwater is a major concern in rural areas. The flower petal of Shorea robusta, commonly known as sal tree, is used in the present study both in its native form and Ca-impregnated activated form to eradicate excess fluoride from simulated wastewater. Response surface methodology (RSM) was used for experimental designing and analyzing optimum condition for carbonization vis-à-vis calcium impregnation for preparation of adsorbent. During carbonization, temperature, time and weight ratio of calcium chloride to sal flower petal (SFP) have been considered as input factors and percentage removal of fluoride as response. Optimum condition for carbonization has been obtained as temperature, 500 °C; time, 1 h and weight ratio, 2.5 and the sample prepared has been termed as calcium-impregnated carbonized sal flower petal (CCSFP). Optimum condition as analyzed by one-factor-at-a-time (OFAT) method is initial fluoride concentration, 2.91 mg/L; pH 3 and adsorbent dose, 4 g/L. CCSFP shows maximum removal of 98.5% at this condition. RSM has also been used for finding out optimum condition for defluoridation considering initial concentration, pH and adsorbent dose as input parameters. The optimum condition as analyzed by RSM is: initial concentration, 5 mg/L; pH 3.5 and adsorbent dose, 2 g/L. Kinetic and equilibrium data follow Ho pseudo-second-order kinetic model and Freundlich isotherm model, respectively. Adsorption capacity of CCSFP has been found to be 5.465 mg/g. At optimized condition, CCSFP has been found to remove fluoride (80.4%) efficiently from groundwater collected from Bankura district in West Bengal, a fluoride-contaminated province in India.

The effect of tooth brushing and flossing sequence on interdental plaque reduction and fluoride retention: A randomized controlled clinical trial.

PubMed

Mazhari, Fatemeh; Boskabady, Marzie; Moeintaghavi, Amir; Habibi, Atieh

2018-05-09

Mechanical plaque control methods such as brushing and flossing are highly recommended to remove dental plaque. The aim of this study is to evaluate the efficacy of the sequence of brushing and flossing on reducing interdental plaque and increasing fluoride retention in that area. This randomized controlled crossover trial was conducted on 25 dental students. After prophylaxis, they were asked to discontinue all forms of oral hygiene for 48 hours. The study was performed in two phases with two-week washout intervals. In one phase, they first brushed, then flossed (sequence 1: brush-floss group). In the other phase they initially used dental floss then brushed (sequence 2: floss-brush group). At each phase, dental plaque (using the Rustogi Modified Navy Plaque Index) and fluoride concentrations (using a fluoride ion specific electrode) were measured before and after flossing and brushing, and the dental plaque reduction and fluoride increase were compared between the two groups using the mixed model test. A significance level of 5% was selected. In the floss-brush group interdental and whole plaque was reduced significantly more than the brush-floss group (p = 0.001, p = 0.009 respectively). However, marginal plaque did not show any statistically significant difference between the two groups (p = 0.2). Fluoride concentrations in interdental plaque were significantly higher in the floss-brush group than the other group (p = 0.027). The results showed that flossing followed by brushing is preferred to brushing then flossing in order to reduce interdental plaque and increase fluoride concentration in interdental plaque. This article is protected by copyright. All rights reserved. © 2018 American Academy of Periodontology.

Ab initio study of the diatomic fluorides FeF, CoF, NiF, and CuF.

PubMed

Koukounas, Constantine; Mavridis, Aristides

2008-11-06

The late-3d transition-metal diatomic fluorides MF = FeF, CoF, NiF, and CuF have been studied using variational multireference (MRCI) and coupled-cluster [RCCSD(T)] methods, combined with large to very large basis sets. We examined a total of 35 (2S+1)|Lambda| states, constructing as well 29 full potential energy curves through the MRCI method. All examined states are ionic, diabatically correlating to M(+)+F(-)((1)S). Notwithstanding the "eccentric" character of the 3d transition metals and the difficulties to accurately be described with all-electron ab initio methods, our results are, in general, in very good agreement with available experimental numbers.

Focus on fluorides: update on the use of fluoride for the prevention of dental caries.

PubMed

Carey, Clifton M

2014-06-01

Improving the efficacy of fluoride therapies reduces dental caries and lowers fluoride exposure. Fluoride is delivered to the teeth systemically or topically to aid in the prevention of dental caries. Systemic fluoride from ingested sources is in blood serum and can be deposited only in teeth that are forming in children. Topical fluoride is from sources such as community water, processed foods, beverages, toothpastes, mouthrinses, gels, foams, and varnishes. The United States Centers for Disease Control and Prevention (CDC) and the American Dental Association (ADA) have proposed changes in their long standing recommendations for the amount of fluoride in community drinking water in response to concerns about an increasing incidence of dental fluorosis in children. Current research is focused on the development of strategies to improve fluoride efficacy. The purpose of this update is to inform the reader about new research and policies related to the use of fluoride for the prevention of dental caries. Reviews of the current research and recent evidence based systematic reviews on the topics of fluoride are presented. Topics discussed include: updates on community water fluoridation research and policies; available fluoride in dentifrices; fluoride varnish compositions, use, and recommendations; and other fluoride containing dental products. This update provides insights into current research and discusses proposed policy changes for the use of fluoride for the prevention of dental caries. The dental profession is adjusting their recommendations for fluoride use based on current observations of the halo effect and subsequent outcomes. The research community is focused on improving the efficacy of fluoride therapies thus reducing dental caries and lowering the amount of fluoride required for efficacy. Copyright © 2014 Elsevier Inc. All rights reserved.

The cariostatic mechanisms of fluoride.

PubMed

Rošin-Grget, Kata; Peroš, Kristina; Sutej, Ivana; Bašić, Krešimir

2013-11-01

This article discusses the possible cariostatic mechanisms of the action of fluoride. In the past, fluoride inhibition of caries was ascribed to reduced solubility of enamel due to incorporation of fluoride (F-) into the enamel minerals. The present evidence from clinical and laboratory studies suggests that the caries-preventive mode of action of fluoride is mainly topical. There is convincing evidence that fluoride has a major effect on demineralisation and remineralisation of dental hard tissue. The source of this fluoride could either be fluorapatite (formed due to the incorporation of fluoride into enamel) or calcium fluoride (CaF2)-like precipitates, which are formed on the enamel and in the plaque after application of topical fluoride. Calcium fluoride deposits are protected from rapid dissolution by a phosphate -protein coating of salivary origin. At lower pH, the coating is lost and an increased dissolution rate of calcium fluoride occurs. The CaF2, therefore, act as an efficient source of free fluoride ions during the cariogenic challenge. The current evidence indicates that fluoride has a direct and indirect effect on bacterial cells, although the in vivo implications of this are still not clear. A better understanding of the mechanisms of the action of fluoride is very important for caries prevention and control. The effectiveness of fluoride as a cariostatic agent depends on the availability of free fluoride in plaque during cariogenic challenge, i.e. during acid production. Thus, a constant supply of low levels of fluoride in biofilm/saliva/dental interference is considered the most beneficial in preventing dental caries. Copyright © 2013 by Academy of Sciences and Arts of Bosnia and Herzegovina.

Fluoride Supplementation Adherence and Barriers in a Community Without Water Fluoridation.

PubMed

Flood, Shannon; Asplund, Karin; Hoffman, Benjamin; Nye, Allison; Zuckerman, Katharine E

2017-04-01

To prevent early childhood caries, the American Dental Association recommends oral fluoride supplementation for children in communities lacking water fluoridation who are at high caries risk. However, patient adherence to oral fluoride supplementation has not been studied in this population. This study assessed adherence to oral fluoride and barriers to adherence in a community lacking water fluoridation. A self-administered survey was completed in a systematic sample of 209 parents of children aged 6 months to 4 years, during a primary care visit in an urban academic medical center. Participants reported frequency of administering oral fluoride to their children, as well as agreement or disagreement with proposed barriers to supplementation. Bivariate and multivariate analyses were used to assess adherence with oral supplementation and the association of barriers to supplementation and child receipt of fluoride on the day before. More than half of parents either had not or did not know if their child had received fluoride on the day before. Approximately 1 in 4 of parents had given fluoride in 0 of the previous 7 days. Difficulty remembering to give fluoride and agreeing that the child does not need extra fluoride were associated with not receiving fluoride on the day before. Adherence to oral fluoride supplementation in the primary care setting is low. Difficulty remembering to give fluoride daily is the greatest barrier to adherence. Further research on interventions to reduce common barriers is needed to increase fluoride administration and reduce early childhood caries in communities lacking water fluoridation. Copyright © 2016 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

Slow-release fluoride devices for the control of dental decay.

PubMed

Chong, Lee Yee; Clarkson, Jan E; Dobbyn-Ross, Lorna; Bhakta, Smriti

2014-11-28

Slow-release fluoride devices have been investigated as a potentially cost-effective method of reducing dental caries in people with high risk of disease. To evaluate the effectiveness and safety of different types of slow-release fluoride devices on preventing, arresting, or reversing the progression of carious lesions on all surface types of primary (deciduous) and permanent teeth. We searched the following electronic databases: the Cochrane Oral Health Group Trials Register (to 13 August 2014), the Cochrane Central Register of Controlled Trials (CENTRAL) (2014, Issue 7), MEDLINE via Ovid (1946 to 13 August 2014), and EMBASE via Ovid (1980 to 13 August 2014). We searched the US National Institutes of Health Trials Register and the World Health Organization (WHO) International Clinical Trials Registry Platform. We placed no restrictions on the language or date of publication when searching the electronic databases.We first published the review in 2006. The update in 2013 found 302 abstracts, but none of these met the inclusion criteria of the review. Parallel randomised controlled trials (RCTs) comparing slow-release fluoride devices with an alternative fluoride treatment, placebo, or no intervention in all age groups. The main outcomes measures sought were changes in numbers of decayed, missing, and filled teeth or surfaces (DMFT/DMFS in permanent teeth or dmft/dmfs in primary teeth), and progression of carious lesions through enamel and into dentine. We conducted data collection and analysis using standard Cochrane review methods. At least two review authors independently performed all the key steps in the review such as screening of abstracts, application of inclusion criteria, data extraction, and risk of bias assessment. We resolved discrepancies through discussions or arbitration by a third or fourth review author. We found no evidence comparing slow-release fluoride devices against other types of fluoride therapy.We found only one double-blind RCT involving 174 children comparing a slow-release fluoride device (glass beads with fluoride were attached to buccal surfaces of right maxillary first permanent molar teeth) against control (glass beads without fluoride were attached to buccal surfaces of right maxillary first permanent molar teeth). This study was assessed to be at high risk of bias. The study recruited children from seven schools in an area of deprivation that had low levels of fluoride in the water. The mean age at the beginning of the study was 8.8 years and at the termination was 10.9 years. DMFT in permanent teeth or dmft in primary teeth was greater than one at the start of the study and greater than one million colony-forming units of Streptococcus mutans per millilitre of saliva.Although 132 children were still included in the trial at the two-year completion point, examination and statistical analysis was performed on only the 63 children (31 in intervention group, 32 in control group) who had retained the beads (retention rate was 47.7% at two years). Among these 63 children, caries increment was reported to be statistically significantly lower in the intervention group than in the control group (DMFT: mean difference -0.72, 95% confidence interval (CI) -1.23 to -0.21; DMFS: mean difference -1.52, 95% CI -2.68 to -0.36 (very low quality evidence)). Although this difference was clinically significant, it only holds true for those children who maintain the fluoride beads; over 50% of children did not retain the beads.Harms were not reported within the trial report. Evidence for other outcomes sought in this review (progression to of caries lesion, dental pain, healthcare utilisation data) were also not reported. There is insufficeint evidence to determine the caries-inhibiting effect of slow-release fluoride glass beads. The body of evidence available is of very low quality and there is a potential overestimation of benefit to the average child. The applicability of the findings to the wider population is unclear; the study had included children from a deprived area that had low levels of fluoride in drinking water, and were considered at high risk of carries. In addition, the evidence was only obtained from children who still had the bead attached at two years (48% of all available children); children who had lost their slow-release fluoride devices earlier might not have benefited as much from the devices.

Slow-release fluoride devices for the control of dental decay.

PubMed

Chong, Lee-Yee; Clarkson, Jan E; Dobbyn-Ross, Lorna; Bhakta, Smriti

2018-03-01

Slow-release fluoride devices have been investigated as a potentially cost-effective method of reducing dental caries in people with high risk of disease. This is the second update of the Cochrane Review first published in 2006 and previously updated in 2014. To evaluate the effectiveness and safety of different types of slow-release fluoride devices on preventing, arresting, or reversing the progression of carious lesions on all surface types of primary (deciduous) and permanent teeth. Cochrane Oral Health's Information Specialist searched the following electronic databases: Cochrane Oral Health's Trials Register (to 23 January 2018); the Cochrane Central Register of Controlled Trials (CENTRAL; 2017, Issue 12) in the Cochrane Library (searched 23 January 2018); MEDLINE Ovid (1946 to 23 January 2018); and Embase Ovid (1980 to 23 January 2018). The US National Institutes of Health Ongoing Trials Register ClinicalTrials.gov, and the World Health Organization International Clinical Trials Registry Platform were searched for ongoing trials (23 January 2018). We placed no restrictions on the language or date of publication when searching the electronic databases. Parallel randomised controlled trials (RCTs) comparing slow-release fluoride devices with an alternative fluoride treatment, placebo, or no intervention in all age groups. The main outcome measures sought were changes in numbers of decayed, missing, and filled teeth or surfaces (DMFT/DMFS in permanent teeth or dmft/dmfs in primary teeth), and progression of carious lesions through enamel and into dentine. We conducted data collection and analysis using standard Cochrane review methods. At least two review authors independently performed all the key steps in the review such as screening of abstracts, application of inclusion criteria, data extraction, and risk of bias assessment. We resolved discrepancies through discussions or arbitration by a third or fourth review author. We found no evidence comparing slow-release fluoride devices against other types of fluoride therapy.We found only one double-blind RCT involving 174 children comparing a slow-release fluoride device (glass beads with fluoride were attached to buccal surfaces of right maxillary first permanent molar teeth) against control (glass beads without fluoride were attached to buccal surfaces of right maxillary first permanent molar teeth). This study was assessed to be at high risk of bias. The study recruited children from seven schools in an area of deprivation that had low levels of fluoride in the water. The mean age at the beginning of the study was 8.8 years and at the termination was 10.9 years. DMFT in permanent teeth or dmft in primary teeth was greater than one at the start of the study and greater than one million colony-forming units of Streptococcus mutans per millilitre of saliva.Although 132 children were still included in the trial at the two-year completion point, examination and statistical analysis was performed on only the 63 children (31 in intervention group, 32 in control group) who had retained the beads (retention rate was 47.7% at 2 years). Among these 63 children, caries increment was reported to be statistically significantly lower in the intervention group than in the control group (DMFT: mean difference -0.72, 95% confidence interval (CI) -1.23 to -0.21; DMFS: mean difference -1.52, 95% CI -2.68 to -0.36 (very low-quality evidence)). Although this difference was clinically significant, it only holds true for those children who maintain the fluoride beads; over 50% of children did not retain the beads.Harms were not reported within the trial report. Evidence for other outcomes sought in this review (progression to of caries lesion, dental pain, healthcare utilisation data) were also not reported. There is insufficient evidence to determine the caries-inhibiting effect of slow-release fluoride glass beads. The body of evidence available is of very low quality and there is a potential overestimation of benefit to the average child. The applicability of the findings to the wider population is unclear; the study had included children from a deprived area that had low levels of fluoride in drinking water, and were considered at high risk of caries. In addition, the evidence was only obtained from children who still had the bead attached at 2 years (48% of all available children); children who had lost their slow-release fluoride devices earlier might not have benefited as much from the devices.

Prevention and Treatment of White Spot Lesions During and After Treatment with Fixed Orthodontic Appliances: a Systematic Literature Review

PubMed Central

Lopatiene, Kristina; Lapenaite, Egle

2016-01-01

ABSTRACT Objectives The aim of the systematic literature review is to update the evidence for the prevention of white spot lesions, using materials containing fluoride and/or casein phosphopeptide-amorphous calcium phosphate during and after treatment with fixed orthodontic appliances. Material and Methods Information search for controlled studies on humans published between January 2008 and February 2016 was performed in PubMed, ScienceDirect, Embase, The Cochrane Library. Inclusion criteria were: the English language, study on humans, patients undergoing orthodontic treatment with fixed appliances, randomized or quasi-randomized controlled clinical studies fluoride-containing product or casein derivates used throughout the appliance therapy or straightaway after debonding. Results 326 articles were reviewed (Embase 141, PubMed 129, ScienceDirect 41, Cochrane 15). Twelve clinical studies fulfilled all inclusion criteria. Use of fluoridated toothpaste had a remineralizing effect on white spot lesions (WSLs) (P < 0.05); fluoride varnish and casein supplements were effective in prevention and early treatment of WSLs (P < 0.05). Conclusions Early detection of white spot lesions during orthodontic treatment would allow implementing preventive measures to control the demineralization process before lesions progress. The systemic review has showed that the usage of fluoride and casein supplements in ameliorating white spot lesions during and after fixed orthodontic treatment is significantly effective. However the use of casein phosphopeptide-amorphous calcium phosphate can be more beneficial than fluoride rinse in the reduction of demineralization spots. PMID:27489605

[The effect of fluoride on electrochemical corrosion of the dental pure titanium before and after adhesion of Streptococcus mutans].

PubMed

Geng, Li; Qiao, Guang-yan; Gu, Kai-ka

2016-04-01

To investigate the effect of fluoride on electrochemical corrosion of the dental pure titanium before and after adhesion of Streptococcus mutans. The dental pure titanium specimens were tested by electrochemical measurement system including electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curve (PD) methods in artificial saliva with 0 g/L and 1.0 g/L sodium fluoride before and after dipped into culture medium with Streptococcus mutans for 24 h. The corrosion parameters, including the polarization resistance (R(ct)), corrosion potential (E(corr)), pitting breakdown potential (E(b)), and the difference between E(corr) and E(b) representing the "pseudo-passivation" (ΔE) obtained from the electrochemical tests were used to evaluate the corrosion resistance of dental pure titanium. The data were statistically analyzed by 2×2 factorial statistical analysis to examine the effect of sodium fluoride and adhesion of Streptococcus mutans using SPSS 12.0 software package. The results showed that the corrosion parameters including R(ct), Ecorr, E(b), and ΔE of pure titanium had significant difference between before and after adhesion of Streptococcus mutans in the same solution(P<0.05), and in artificial saliva with 0 g/L and 1.0 g/L sodium fluoride(P<0.05). The dental pure titanium was prone to corrosion in artificial saliva with sodium fluoride. The corrosion resistance of pure titanium decreased distinctly after immersed in culture medium with Streptococcus mutans.

Dental fluorosis in populations from Chiang Mai, Thailand with different fluoride exposures - Paper 2: The ability of fluorescence imaging to detect differences in fluorosis prevalence and severity for different fluoride intakes from water

PubMed Central

2012-01-01

Background To assess the ability of fluorescence imaging to detect a dose response relationship between fluorosis severity and different levels of fluoride in water supplies compared to remote photographic scoring in selected populations participating in an observational, epidemiological survey in Chiang Mai, Thailand. Methods Subjects were male and female lifetime residents aged 8-13 years. For each child the fluoride content of cooking water samples (CWS) was assessed to create categorical intervals of water fluoride concentration. Fluorescence images were taken of the maxillary central incisors and analyzed for dental fluorosis using two different software techniques. Output metrics for the fluorescence imaging techniques were compared to TF scores from blinded photographic scores obtained from the survey. Results Data from 553 subjects were available. Both software analysis techniques demonstrated significant correlations with the photographic scores. The metrics for area effected by fluorosis and the overall fluorescence loss had the strongest association with the photographic TF score (Spearman’s rho 0.664 and 0.652 respectively). Both software techniques performed well for comparison of repeat fluorescence images with ICC values of 0.95 and 0.85 respectively. Conclusions This study supports the potential use of fluorescence imaging for the objective quantification of dental fluorosis. Fluorescence imaging was able to discriminate between populations with different fluoride exposures on a comparable level to remote photographic scoring with acceptable levels of repeatability. PMID:22908997

Investigation on the remineralization effect of arginine toothpaste for early enamel caries: nanotribological and nanomechanical properties

NASA Astrophysics Data System (ADS)

Yu, Ping; Arola, Dwayne D.; Min, Jie; Yu, Dandan; Xu, Zhou; Li, Zhi; Gao, Shanshan

2016-11-01

Remineralization is confirmed as a feasible method to restore early enamel caries. While there is evidence that the 8% arginine toothpaste has a good remineralization effect by increasing surface microhardness, the repair effect on wear-resistance and nanomechanical properties still remains unclear. Therefore, this research was conducted to reveal the nanotribological and nanomechanical properties changes of early caries enamel after remineralized with arginine toothpaste. Early enamel caries were created in bovine enamel blocks, and divided into three groups according to the treatment solutions: distilled and deionized water (DDW group), arginine toothpaste slurry (arginine group) and fluoride toothpaste slurry (fluoride group). All of the samples were subjected to pH cycling for 12 d. The nanotribological and nanomechanical properties were evaluated via the nanoscratch and nanoindentation tests. The wear depth and scratch morphology were observed respectively by scanning probe microscopic (SPM) and scanning electron microscopy (SEM). Finally, x-ray photoelectron spectroscopy (XPS) was used for element analysis of remineralized surfaces. Results showed that the wear depth of early caries enamel decreased after remineralization treatment and both the nanohardness and elastic modulus increased. Compared with the fluoride group, the arginine group exhibited higher nanohardness and elastic modulus with higher levels of calcium, fluoride, nitrogen and phosphorus; this group also underwent less wear and related damage. Overall, the synergistic effect of arginine and fluoride in arginine toothpaste achieves better nanotribological and nanomechanical properties than the single fluoride toothpaste, which could have significant impact on fight against early enamel caries.

[Adaptation of the (18)FDG module for the preparation of a sodium fluoride [(18)F] injection solution in agreement with the United States (USP 32) and European Pharmacopeia (PhEur 6)].

PubMed

Martínez, T; Cordero, B; Medín, S; Sánchez Salmón, A

2011-01-01

To establish an automated procedure for the preparation of sodium fluoride (18)F injection using the resources available in our laboratory for the preparation of (18)FDG and to analyze the repercussion of the conditioning column of the fluoride ion entrapment on the characteristics of the final product. The sequence of an (18)FDG synthesis module prepared so that it traps the fluoride ion from the cyclotron in ion-exchange resin diluted with 0.9% sodium chloride. The final solution was dosified and sterilized in a final vial in an automatized dispensing module. Three different column conditioning protocols within the process were tested. Quality controls were run according to USP 32 and EurPh 6, adding control of ethanol levels of residual solvent and quality controls of the solution at 8 h post-preparation. Activation of the resin cartridges with ethanol and water was the chosen procedure, with fluoride ion trapping > 95% and pH around 7. Ethanol levels were < 5.000 ppm. Quality controls at 8 h indicated that the solution was in compliance with the USP 32 and EurPh 6 specifications. This is an easy, low-cost, reliable automated method for sodium fluoride preparation in PET facilities with existing equipment for (18)FDG synthesis and quality control. Copyright © 2010 Elsevier España, S.L. y SEMNIM. All rights reserved.

White spot lesions: prevention and management during the orthodontic treatment.

PubMed

Zabokova-Bilbilova, Efka; Popovska, Lidija; Kapusevska, Biljana; Stefanovska, Emilija

2014-01-01

The formation of white spot lesions, or enamel demineralization, around fixed orthodontic attachments is a common complication during and following fixed orthodontic treatment, which marks the result of a successfully completed case. This article is a contemporary review of the risk factors and preventive methods of these orthodontics scars. Preventive programmes must be emphasized to all orthodontic patients. The responsibility of an orthodontist is to minimize the risk of the patient having decalcification as a consequence of orthodontic treatment by educating and motivating the patients for excellent oral hygiene practice. Prophylaxis with topical fluoride application should be implemented: high-fluoride toothpastes, fluoride mouthwashes, gels and varnishes during and after the orthodontic treatment, especially for patients at high risk of caries.

Determination of fluoride in water - A modified zirconium-alizarin method

USGS Publications Warehouse

Lamar, W.L.

1945-01-01

A convenient, rapid colorimetric procedure using the zirconium-alizarin indicator acidified with sulfuric acid for the determination of fluoride in water is described. Since this acid indicator is stable indefinitely, it is more useful than other zirconium-alizarin reagents previously reported. The use of sulfuric acid alone in acidifying the zirconium-alizarin reagent makes possible the maximum suppression of the interference of sulfate. Control of the pH of the samples eliminates errors due to the alkalinity of the samples. The fluoride content of waters containing less than 500 parts per million of sulfate and less than 1000 p.p.m. of chloride may be determined within a limit of 0.1 p.p.m. when a 100-ml. sample is used.

Synthesis of adsorbent from Tamarix hispida and modified by lanthanum metal for fluoride ions removal from wastewater: Adsorbent characteristics and real wastewater treatment data.

PubMed

Habibi, Nasim; Rouhi, Parham; Ramavandi, Bahman

2017-08-01

This data article describes a facile method for production of an adsorbent from Tamarix hispida wasted wood and modified by lanthanum metal for fluoride ions removal from wastewater. The main characteristics of the adsorbent consist of BET surface area, functional groups, and elemental analysis is presented. The data for attenuating the pollutants from a real wastewater treatment which was provided from a glass factory is also represented. More than 90% of fluoride content of the real wastewater was treated by the adsorbent. Generally, these data would be informative for extend research aim to industrial wastewater treatment and those who work in the wastewater treatment plants.

Real single ion solvation free energies with quantum mechanical simulation

DOE PAGES

Duignan, Timothy T.; Baer, Marcel D.; Schenter, Gregory K.; ...

2017-07-04

Single ion solvation free energies are one of the most important properties of electrolyte solutions and yet there is ongoing debate about what these values are. Only the values for neutral ion pairs are known. Here, we use DFT interaction potentials with molecular dynamics simulation (DFT-MD) combined with a modified version of the quasi-chemical theory (QCT) to calculate these energies for the lithium and fluoride ions. A method to correct for the error in the DFT functional is developed and very good agreement with the experimental value for the lithium fluoride pair is obtained. Moreover, this method partitions the energiesmore » into physically intuitive terms such as surface potential, cavity and charging energies which are amenable to descriptions with reduced models. Here, our research suggests that lithium's solvation free energy is dominated by the free energetics of a charged hard sphere, whereas fluoride exhibits significant quantum mechanical behavior that cannot be simply described with a reduced model.« less

Real single ion solvation free energies with quantum mechanical simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duignan, Timothy T.; Baer, Marcel D.; Schenter, Gregory K.

Single ion solvation free energies are one of the most important properties of electrolyte solutions and yet there is ongoing debate about what these values are. Only the values for neutral ion pairs are known. Here, we use DFT interaction potentials with molecular dynamics simulation (DFT-MD) combined with a modified version of the quasi-chemical theory (QCT) to calculate these energies for the lithium and fluoride ions. A method to correct for the error in the DFT functional is developed and very good agreement with the experimental value for the lithium fluoride pair is obtained. Moreover, this method partitions the energiesmore » into physically intuitive terms such as surface potential, cavity and charging energies which are amenable to descriptions with reduced models. Here, our research suggests that lithium's solvation free energy is dominated by the free energetics of a charged hard sphere, whereas fluoride exhibits significant quantum mechanical behavior that cannot be simply described with a reduced model.« less

Potassium permanganate-glutaraldehyde chemiluminescence system catalyzed by gold nanoprisms toward selective determination of fluoride.

PubMed

Abolhasani, Jafar; Hassanzadeh, Javad; Ghorbani-Kalhor, Ebrahim

2016-02-01

Gold and silver nanoparticles (NPs) are shown to exert a positive effect on the chemiluminescence (CL) reaction of permanganate aldehydes. Interestingly, between various shapes examined, Au nanoprisms have the highest beneficial effect. This effect is even more notable in the presence of sodium dodecyl sulfate (SDS) surfactant. UV-vis spectra and transmission electron microscopy were used to characterize the NP shapes and sizes. Furthermore, it was observed that iron(III) ions can slightly increase CL emission of this system. This intensification is very effective in the presence of fluoride ions (F(-)). These observations form the basis of the method for the high sensitive determination of F(-) in the 6-1200 nmol L(-1) concentration range, with a detection limit of 2.1 nmol L(-1). The proposed method has good precision and was satisfactorily used in the selective determination of low concentrations of fluoride ion in real samples. Copyright © 2015 John Wiley & Sons, Ltd.

Magmatic evolution and controls on rare metal-enrichment of the Strange Lake A-type peralkaline granitic pluton, Québec-Labrador

NASA Astrophysics Data System (ADS)

Siegel, Karin; Vasyukova, Olga V.; Williams-Jones, Anthony E.

2018-05-01

Although it is well known that A-type granites are enriched in the rare earth elements (REE) and other high field strength elements (HFSE), the magmatic processes that concentrate these elements are still poorly understood. The 1.24 Ga Strange Lake pluton in northern Québec-Labrador provides an extraordinary example of hyper-enrichment in the REE, Zr, and Nb in a peralkaline A-type granite. The pluton consists of two hypersolvus granite units (southern and northern) and a transsolvus granite, all of which contain perthitic alkali feldspar as the earliest major mineral; the transsolvus granite also contains separate albite and microcline crystals. Arfvedsonite, a sodic amphibole, occurs exclusively as phenocrysts in the transsolvus granite, whereas in the hypersolvus granite it is present as a late, interstitial phase. The primary HFSE minerals are zircon, monazite-(Ce), gagarinite-(Ce) and the pyrochlore group minerals. Magma evolution was monitored by the alumina content in the bulk rock, which decreases from the southern to the northern hypersolvus granite and is lowest in the transsolvus granite. Alkalinity indices and bulk Si, Fe, Rb, REE, Zr, Nb concentrations show the opposite trend. Alkali feldspar compositions mirror the trend shown by the bulk rock, i.e., decreasing Al contents are accompanied by increasing Si, Fe3+, REE, Zr and Nb contents. The major driving forces for the evolution of the hypersolvus magma prior to emplacement were the early separation of a fluoride melt from the silicate melt and the crystallization of alkali feldspar and HFSE-rich phases (zircon, monazite-(Ce), pyrochlore group). An alkali feldspar-rich crystal-mush containing LREE-fluoride melt droplets was emplaced as the least evolved southern hypersolvus granite. Massive fractionation of alkali feldspar led to a sharp increase in ƒH2O and F- activity in the magma chamber that triggered the crystallization of arfvedsonite and was followed by emplacement of the northern hypersolvus granite, which contained a higher proportion of LREE-fluoride melt droplets. Further evolution in the magma chamber led to a transition from a miaskitic to an agpaitic composition. The transsolvus granite was intruded in the form of a low viscosity crystal mush of alkali feldspar, quartz, arfvedsonite (after appreciable crystallization of arfvedsonite) and LREE-fluoride melt droplets. Upon emplacement, arfvedsonite (and gagarinite-(Ce)) crystals segregated as cumulates in response to a combination of flow differentiation and gravity settling. The immiscible fluoride melt accumulated in a volatile-rich residual silicate magma, which migrated to the top of the pluton where it formed the F-REE-rich cores of highly mineralized pegmatites.

Oral fluoride levels 1 h after use of a sodium fluoride rinse: effect of sodium lauryl sulfate.

PubMed

Vogel, Gerald L; Schumacher, Gary E; Chow, Laurence C; Tenuta, Livia M A

2015-01-01

Increasing the concentration of free fluoride in oral fluids is an important goal in the use of topical fluoride agents. Although sodium lauryl sulfate (SLS) is a common dentifrice ingredient, the influence of this ion on plaque fluid and salivary fluid fluoride has not been examined. The purpose of this study was to investigate the effect of SLS on these parameters and to examine the effect of this ion on total (or whole) plaque fluoride, an important source of plaque fluid fluoride after a sufficient interval following fluoride administration, and on total salivary fluoride, a parameter often used as a surrogate measure of salivary fluid fluoride. Ten subjects accumulated plaque for 48 h before rinsing with a 12 mmol/l NaF (228 µg/g F) rinse containing or not containing 0.5% (w/w) SLS. SLS had no statistically significant effect on total plaque and total saliva fluoride but significantly increased salivary fluid and plaque fluid fluoride (by 147 and 205%, respectively). These results suggest that the nonfluoride components of topical agents can be manipulated to improve the fluoride release characteristics from oral fluoride reservoirs and that statistically significant change may be observed in plaque fluid and salivary fluid fluoride concentrations that may not be observed in total plaque and total saliva fluoride concentrations.

The effect of fluoridation and its discontinuation on fluoride profiles in the alveolar bone of rat.

PubMed

Ohmi, Kyohei; Nakagaki, Haruo; Tsuboi, Shinji; Okumura, Akihiro; Sugiyama, Tomoko; Thuy, Tran Thu; Robinson, Colin

2005-10-01

We investigated the effect of fluoridation and its discontinuation on fluoride content in the alveolar portion of the mandible in rats. Drinking water with three different fluoride contents (0, 50, 100 ppmF) was given to rats for three different periods (4, 13 and 25 weeks). Fluoride concentrations were measured in the crest, the middle, and the apical parts of the alveolar bone and in the body of the mandible. Furthermore, after fluoridated drinking water was given to rats for 4 or 13 weeks, distilled water was given to them for 21 or 12 weeks respectively; and the effect of the discontinuation on fluoride profiles was investigated. Layer samples were analyzed by abrasive microsampling. Fluoride and phosphorus concentrations were determined by ion-specific electrode and colorimetric procedures, respectively. There was an increase in fluoride concentrations in the mandible in proportion to the fluoride content in the drinking water and the duration of fluoridation. After fluoridation was discontinued, fluoride concentrations in the surface layers of the mandible presented a decrease. Among the four different parts of the mandible, the upper part of the alveolar bone and the alveolar crest part presented the highest rates of reduction. The relative reduction rate of fluoride concentration was closely related to the duration of discontinuation. The alveolar crest was affected most by the discontinuation of fluoridation, presenting the greatest reduction.

Fluoride barriers in Nb/Pb Josephson junctions

NASA Astrophysics Data System (ADS)

Asano, H.; Tanabe, K.; Michikami, O.; Igarashi, M.; Beasley, M. R.

1985-03-01

Josephson tunnel junctions are fabricated using a new class of artificial barriers, metal fluorides (Al fluoride and Zr fluoride). These fluoride barriers are deposited on the surface of a Nb base electrode, which are previously cleaned using a CF4 cleaning process, and covered by a Pb counterelectrode. The junctions with both Al fluoride and Zr fluoride barriers exhibit good tunneling characteristics and have low specific capacitance. In the case of Zr fluoride, it is observed that reasonable resistances are obtained even at thickness greater than 100 A. This phenomenon might be explained by tunneling via localized states in Zr fluoride.

Eukaryotic resistance to fluoride toxicity mediated by a widespread family of fluoride export proteins.

PubMed

Li, Sanshu; Smith, Kathryn D; Davis, Jared H; Gordon, Patricia B; Breaker, Ronald R; Strobel, Scott A

2013-11-19

Fluorine is an abundant element and is toxic to organisms from bacteria to humans, but the mechanisms by which eukaryotes resist fluoride toxicity are unknown. The Escherichia coli gene crcB was recently shown to be regulated by a fluoride-responsive riboswitch, implicating it in fluoride response. There are >8,000 crcB homologs across all domains of life, indicating that it has an important role in biology. Here we demonstrate that eukaryotic homologs [renamed FEX (fluoride exporter)] function in fluoride export. FEX KOs in three eukaryotic model organisms, Neurospora crassa, Saccharomyces cerevisiae, and Candida albicans, are highly sensitized to fluoride (>200-fold) but not to other halides. Some of these KO strains are unable to grow in fluoride concentrations found in tap water. Using the radioactive isotope of fluoride, (18)F, we developed an assay to measure the intracellular fluoride concentration and show that the FEX deletion strains accumulate fluoride in excess of the external concentration, providing direct evidence of FEX function in fluoride efflux. In addition, they are more sensitive to lower pH in the presence of fluoride. These results demonstrate that eukaryotic FEX genes encode a previously unrecognized class of fluoride exporter necessary for survival in standard environmental conditions.

Eukaryotic resistance to fluoride toxicity mediated by a widespread family of fluoride export proteins

PubMed Central

Li, Sanshu; Smith, Kathryn D.; Davis, Jared H.; Gordon, Patricia B.; Breaker, Ronald R.; Strobel, Scott A.

2013-01-01

Fluorine is an abundant element and is toxic to organisms from bacteria to humans, but the mechanisms by which eukaryotes resist fluoride toxicity are unknown. The Escherichia coli gene crcB was recently shown to be regulated by a fluoride-responsive riboswitch, implicating it in fluoride response. There are >8,000 crcB homologs across all domains of life, indicating that it has an important role in biology. Here we demonstrate that eukaryotic homologs [renamed FEX (fluoride exporter)] function in fluoride export. FEX KOs in three eukaryotic model organisms, Neurospora crassa, Saccharomyces cerevisiae, and Candida albicans, are highly sensitized to fluoride (>200-fold) but not to other halides. Some of these KO strains are unable to grow in fluoride concentrations found in tap water. Using the radioactive isotope of fluoride, 18F, we developed an assay to measure the intracellular fluoride concentration and show that the FEX deletion strains accumulate fluoride in excess of the external concentration, providing direct evidence of FEX function in fluoride efflux. In addition, they are more sensitive to lower pH in the presence of fluoride. These results demonstrate that eukaryotic FEX genes encode a previously unrecognized class of fluoride exporter necessary for survival in standard environmental conditions. PMID:24173035

40 CFR 471.21 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... mg/off-kg (pounds per million off-pounds) of forged magnesium cooled with water Chromium 1.27 0.520... million off-pounds) of magnesium forged Chromium 0.018 0.007 Zinc 0.059 0.025 Ammonia 5.32 2.34 Fluoride 2... cast with direct chill methods Chromium 1.74 0.711 Zinc 5.77 2.41 Ammonia 527 232 Fluoride 235 105 Oil...

Fluoride metabolism when added to salt.

PubMed

Whitford, Gary M

2005-01-01

The purpose of this review is to present the general characteristics of the metabolism of fluoride particularly as it occurs when ingested with fluoridated salt. Following the absorption of salt-borne fluoride from the stomach and intestines, its metabolism is identical to that of water-borne fluoride or other vehicles containing ionized fluoride. Because fluoridated salt is almost always ingested with food, however, absorption from the gastrointestinal tract may be delayed or reduced. Reports dealing with this subject have shown that fluoride absorption is delayed and, therefore, peak plasma concentrations are lower than when fluoride is ingested with water. The amount of ingested fluoride that is finally absorbed, however, is not appreciably affected unless the meal is composed mainly of components with high calcium concentrations. In this case, the extent of absorption can be reduced by as much as 50%. Fluoridated salt is also ingested less frequently than fluoridated water. Data are presented to show that the dose size and frequency of ingestion have only minor effects on fluoride retention in the body and on the concentrations in plasma, bone and enamel. Finally, calculations are presented to show that the risk of acute toxicity from fluoridated salt is virtually non-existent.

Fluoride content of still bottled water in Australia.

PubMed

Cochrane, N J; Saranathan, S; Morgan, M V; Dashper, S G

2006-09-01

Recently there has been a considerable increase in the consumption of bottled water in Australia. Overseas studies have found the fluoride levels in many bottled waters are well below levels considered optimal for preventing dental caries. This raises the concern that if bottled water is regularly consumed an effective means of preventing dental caries is unavailable. The aim of this study was to determine the fluoride concentration in 10 popular brands of still bottled water currently sold in Australia. The fluoride content of water samples were determined using an ion analyser and compared to a fluoride standard. The fluoride concentration of all bottled waters was less than 0.08 ppm. Only three of the 10 brands indicated the fluoride content on their labels. Melbourne reticulated water was found to be fluoridated at 1.02 ppm. All bottled waters tested contained negligible fluoride which justifies the concern that regular consumption of bottled water may reduce the benefits gained from water fluoridation. It is recommended that all bottled water companies should consider stating their fluoride content on their labels. This will inform consumers and dental care providers of the levels of fluoride in bottled water and allow an informed decision regarding consumption of fluoridated versus non-fluoridated drinking water.

Stochastic volatility models and Kelvin waves

NASA Astrophysics Data System (ADS)

Lipton, Alex; Sepp, Artur

2008-08-01

We use stochastic volatility models to describe the evolution of an asset price, its instantaneous volatility and its realized volatility. In particular, we concentrate on the Stein and Stein model (SSM) (1991) for the stochastic asset volatility and the Heston model (HM) (1993) for the stochastic asset variance. By construction, the volatility is not sign definite in SSM and is non-negative in HM. It is well known that both models produce closed-form expressions for the prices of vanilla option via the Lewis-Lipton formula. However, the numerical pricing of exotic options by means of the finite difference and Monte Carlo methods is much more complex for HM than for SSM. Until now, this complexity was considered to be an acceptable price to pay for ensuring that the asset volatility is non-negative. We argue that having negative stochastic volatility is a psychological rather than financial or mathematical problem, and advocate using SSM rather than HM in most applications. We extend SSM by adding volatility jumps and obtain a closed-form expression for the density of the asset price and its realized volatility. We also show that the current method of choice for solving pricing problems with stochastic volatility (via the affine ansatz for the Fourier-transformed density function) can be traced back to the Kelvin method designed in the 19th century for studying wave motion problems arising in fluid dynamics.

Health Effects Associated with Water Fluoridation.

ERIC Educational Resources Information Center

Richmond, Virginia L.

1979-01-01

Discussion is presented concerning fluoridation of water supplies. Correlation between fluoride in drinking water and improved dental health is reviewed. Relationship is expressed between fluoridation and reduced tooth decay. Use of fluoride in treating skeletal disorders is discussed. Author advocates fluoridating water supplies. (SA)

Hydroxyapatite, fluor-hydroxyapatite and fluorapatite produced via the sol-gel method: bonding to titanium and scanning electron microscopy.

PubMed

Tredwin, Christopher J; Georgiou, George; Kim, Hae-Won; Knowles, Jonathan C

2013-05-01

Hydroxyapatite (HA), fluor-hydroxyapatite (FHA) with varying levels of fluoride ion substitution and fluorapatite (FA) production has been characterised and optimised by the sol-gel method and the dissolution and biological properties of these materials were investigated. It was the objective of this study to investigate the potential bond strength and interaction of these materials with titanium. HA, FHA and FA were synthesised by a sol-gel method. Calcium nitrate and triethyl phosphite were used as precursors under an ethanol-water based solution. Different amounts of ammonium fluoride (NH4F) were incorporated for the preparation of the FHA and FA sol-gels. Using a spin coating technique the sol-gels were coated onto commercially pure titanium disks and crystallised at various temperatures. Using scanning electron microscopy (SEM) and elemental analysis, the surface characteristics, coating thickness and interaction of the Ti substrate and coating were investigated. The bond strengths of the coating to the Ti were investigated using an Instron Universal Load Testing Machine. Statistical analysis was performed with a two-way analysis of variance and post hoc testing with a Bonferroni correction. (1) Coating speed inversely influenced the coating thickness. (2) Increasing fluoride ion substitution and heating temperature significantly increased bond strength and (3) increasing fluoride ion substitution increased the coating thickness. FHA and FA synthesised using the sol-gel technique may offer a superior alternative to coating titanium implants with HA and plasma spraying. HA, FHA and FA materials synthesised by the sol-gel method may also have a use as bone grafting materials. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Practice-Tailored Facilitation to Improve Pediatric Preventive Care Delivery: A Randomized Trial

PubMed Central

Schiltz, Nicholas K.; Sattar, Abdus; Stange, Kurt C.; Nevar, Ann H.; Davey, Christina; Ferretti, Gerald A.; Howell, Diana E.; Strosaker, Robyn; Vavrek, Pamela; Bader, Samantha; Ruhe, Mary C.; Cuttler, Leona

2014-01-01

OBJECTIVE: Evolving primary care models require methods to help practices achieve quality standards. This study assessed the effectiveness of a Practice-Tailored Facilitation Intervention for improving delivery of 3 pediatric preventive services. METHODS: In this cluster-randomized trial, a practice facilitator implemented practice-tailored rapid-cycle feedback/change strategies for improving obesity screening/counseling, lead screening, and dental fluoride varnish application. Thirty practices were randomized to Early or Late Intervention, and outcomes assessed for 16 419 well-child visits. A multidisciplinary team characterized facilitation processes by using comparative case study methods. RESULTS: Baseline performance was as follows: for Obesity: 3.5% successful performance in Early and 6.3% in Late practices, P = .74; Lead: 62.2% and 77.8% success, respectively, P = .11; and Fluoride: <0.1% success for all practices. Four months after randomization, performance rose in Early practices, to 82.8% for Obesity, 86.3% for Lead, and 89.1% for Fluoride, all P < .001 for improvement compared with Late practices’ control time. During the full 6-month intervention, care improved versus baseline in all practices, for Obesity for Early practices to 86.5%, and for Late practices 88.9%; for Lead for Early practices to 87.5% and Late practices 94.5%; and for Fluoride, for Early practices to 78.9% and Late practices 81.9%, all P < .001 compared with baseline. Improvements were sustained 2 months after intervention. Successful facilitation involved multidisciplinary support, rapid-cycle problem solving feedback, and ongoing relationship-building, allowing individualizing facilitation approach and intensity based on 3 levels of practice need. CONCLUSIONS: Practice-tailored Facilitation Intervention can lead to substantial, simultaneous, and sustained improvements in 3 domains, and holds promise as a broad-based method to advance pediatric preventive care. PMID:24799539

Synthesis of hydroxyapatite nanorods for application in water defluoridation and optimization of process variables: Advantage of ultrasonication with precipitation method over conventional method.

PubMed

Mehta, Dhiraj; Mondal, Poonam; Saharan, Virendra Kumar; George, Suja

2017-07-01

This research work presents the synthesis of hydroxyapatite (Hap) nanorods for defluoridation of drinking water by using both conventional (CM) and ultrasonication with precipitation (USPM) methods. Calcium nitrate was reacted with potassium phosphate in presence of ammonia for controlled pH to synthesize Hap nanorods, which was characterized using FTIR, XRD, SEM, TG-DTA, and TEM/EDS for determining its phase composition, structural and thermal decomposition behavior. When USPM method was used for synthesis, the yield of the Hap nanorods was improved from 83.24±1.0% to 90.2±1.0%, and complete phase transformation occurred with formation of elongated Hap nanorods. Effects of process parameters such as solution pH, contact time and adsorbent dose were studied through response surface methodology (RSM). A simple quadratic model was developed using Central Composite Design (CCD) and optimum parameters for fluoride adsorption process were determined to be pH 7, contact time 3h and adsorbent dose 7g/L for maximum removal capacity. Fluoride removal efficiency was predicted to be 93.64% which was very close to the experimental value obtained at 92.86% using ultrasonically prepared Hap. Fluoride adsorption isotherms fitted the Freundlich isotherm with an adsorption capacity of 1.49mg/g, while the kinetic studies revealed that the process followed pseudo-second order model. The treated water quality parameters such as residual fluoride, calcium leached, total hardness and alkalinity was investigated, and it was observed that all these parameters were within the permissible limits as per WHO and BIS standards. Copyright © 2017 Elsevier B.V. All rights reserved.

Screening high-fluoride and high-arsenic drinking waters and surveying endemic fluorosis and arsenism in Shaanxi province in western China.

PubMed

Zhu, Cansheng; Bai, Guanglu; Liu, Xiaoli; Li, Yue

2006-09-01

The objectives of this study were to screen high-fluoride and high-arsenic drinking waters, to evaluate the effectiveness of fluoride-reducing projects and to assess the present condition of endemic fluorosis and arsenism in Shaanxi province in western China. For screening high-fluoride drinking waters, five water samples were collected from each selected village where dental fluorosis patients were detected in 8-12 year-old children. For evaluating the effectiveness of fluoride-reducing projects, four water samples were collected from each project at end-user level. Fluoride concentrations in water samples were measured by fluoride-selective electrode method or spectrophotometry. Dental fluorosis in children aging 8-12 years was examined according to Horowitz's Tooth Surface Index of Fluorosis. Skeletal fluorosis in adults was detected clinically and radiologically according to Chinese Criteria of Clinical Diagnosis of Skeletal Fluorosis. For screening high-arsenic waters, 20 water samples were collected from each village which was selected from areas characterized by the geographic features to induce high-arsenic underground water, i.e., alluvial plains, ore mining or smelting areas, geothermal artesians, and thermal springs. Arsenic concentrations in water samples were determined by spectrophotometry or arsine generation atomic fluorospectrophotometry. Arsenism in adults aging 40-89 years was examined in villages with arsenic concentrations in drinking water above 0.05 mg/l according to Chinese Criteria for Classification of Endemic Arsenism Areas and Clinical Diagnoses of Endemic Arsenism. The results showed that the fluoride level of 7144 water samples was 1.17 +/- 0.93 mg/l. There were 3396 (47.6%) high-fluoride waters (fluoride level was above 1.0 mg/l) distributing in 786 (45.1%) villages, where about 0.8 million (50.0%) people inhabited. Additionally, the 1315 fluoride-reducing projects were studied. The fluoride level of the projects was 2.79 +/- 1.09 and 0.98 +/- 0.47 mg/l before and after building the projects, which remained at relatively lower level (1.03 +/- 0.47 mg/l). But there were still 58.0% of the projects providing drinking waters with fluoride concentrations beyond 1.0mg/l. The rates of dental fluorosis and skeletal fluorosis were 38.2% and 11.8%, respectively. The arsenic level of 1732 water samples was 0.010 +/- 0.082 mg/l. There were 174 (14.9%) high-arsenic waters (arsenic level was above 0.010 mg/l) being detected, distributing in 41 (38.7%) villages. The arsenic level in 53 (4.5%) water samples was beyond 0.025 mg/l. There were 3 villages with arsenic level in drinking water beyond Chinese National Permissible Limits (0.050 mg/l), and the prevalence rate of arsenism reached 37.0% in these three villages, 3.7%, 22.2%, and 11.1% of subjects suffering from mild, moderate, and severe arsenism, respectively. Conclusively, the wide distribution of high-fluoride drinking waters contributes to the prevalence of dental and skeletal fluorosis in Shaanxi province and the quality of fluoride-reducing projects should be further improved. Ore mining and smelting induces high-arsenic drinking waters, resulting in arsenism prevalence in Shang-luo city. Proper measures should be taken to deal with water pollution in the ore mining and smelting areas in order to solve the high-arsenic water problem in Shaanxi province.

Ionic liquids in tribology.

PubMed

Minami, Ichiro

2009-06-24

Current research on room-temperature ionic liquids as lubricants is described. Ionic liquids possess excellent properties such as non-volatility, non-flammability, and thermo-oxidative stability. The potential use of ionic liquids as lubricants was first proposed in 2001 and approximately 70 articles pertaining to fundamental research on ionic liquids have been published through May 2009. A large majority of the cations examined in this area are derived from 1,3-dialkylimidazolium, with a higher alkyl group on the imidazolium cation being beneficial for good lubrication, while it reduces the thermo-oxidative stability. Hydrophobic anions provide both good lubricity and significant thermo-oxidative stability. The anions decompose through a tribochemical reaction to generate metal fluoride on the rubbed surface. Additive technology to improve lubricity is also explained. An introduction to tribology as an interdisciplinary field of lubrication is also provided.

Absorption, distribution and excretion of inhaled hydrogen fluoride in the rat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, J.B.

1979-01-01

Rats were subjected to whole body HF exposure for 6 hrs or to nose-only HF exposure for 1 hr. Total and/or ionic fluoride concentrations in selected tissues were determined at various times following exposure. In rats sacrificed 6 hrs after whole body exposure, dose-dependent increases in lung, plasma, and kidney total and ionic fluoride concentration occurred. Rats excreted more fluoride in the urine after whole body exposure than could be explained by the amount of HF inhaled. Considerable evidence suggests that airborne HF deposits on fur and is then ingested due to preening activity. Urinary fluoride excretion was increased bymore » nose-only exposure. The urinary fluoride excretion accounted for approximately twice the fluoride estimated to be inhaled during exposure. Tissue fluoride concentrations were elevated immediately after nose-only exposure. Fluoride concentrations in lung and kidney returned to control levels within 12 hrs. Plasma fluoride concentration was slightly elevated 24 hrs after the start of the 1 hr exposure but was at control levels at 96 hrs. Immediately following nose-only exposure, lung ionic fluoride concentrations were less than plasma ionic fluoride concentrations suggesting that the fluoride in the lung had reached that site via plasma transport rather than by inhalation. A dose-dependent increase in plasma ionic fluoride concentration occurred after upper respiratory tract HF exposure providing strong evidence that fluoride is absorbed systemically from that site. The plasma ionic fluoride concentration after upper respiratory tract exposure was of sufficient magnitude to account for the plasma fluoride concentrations observed in intact nose-only exposed rats. (ERB)« less

Exposure to water fluoridation and caries increment.

PubMed

Spencer, A J; Armfield, J M; Slade, G D

2008-03-01

The objective of this cohort study was to examine the association between exposure to water fluoridation and the increment of dental caries in two Australian states: Queensland (Qld)--5 per cent fluoridation coverage; and South Australia (SA)--70 per cent fluoridation coverage. Stratified random samples were drawn from fluoridated Adelaide and the largely non-fluoridated rest-of-state in SA, and fluoridated Townsville and non-fluoridated Brisbane in Qld. Children were enrolled between 1991 and 1992 (SA: 5-15 yrs old, n = 9,980; Qld: 5-12 yrs old, n = 10,695). Follow-up caries status data for 3 years (+/- 1/2 year) were available on 8,183 children in SA and 6,711 children in Qld. Baseline data on lifetime exposure to fluoridated water, use of other fluorides and socio-economic status (SES) were collected by questionnaire, and tooth surface caries status by dental examinations in school dental service clinics. Higher per cent lifetime exposure to fluoridated water (6 categories: 0;1-24; 25-49; 50-74; 75-99; 100 per cent) was a significant predictor (ANOVA, p < 0.01) of lower annualised Net Caries Increment (NCI) for the deciduous dentition in SA and Qld, but only for Qld in the permanent dentition. These associations persisted in multiple linear regression analyses controlling for age, gender, exposure to other fluorides and SES (p < 0.05). Water fluoridation was effective in reducing caries increment, even in the presence of a dilution effect from other fluorides. The effect of fluoridated water consumption was strongest in the deciduous dentition and where diffusion of food and beverages from fluoridated to non-fluoridated areas was less likely.

A selective chemosensor for fluoride ion and its interaction with Calf Thymus DNA

NASA Astrophysics Data System (ADS)

Ghosh, Soumen; Al Masum, Abdulla; Ganguly, Aniruddha; Islam, Md. Maidul; Alam, Md. Akhtarul; Guchhait, Nikhil

2017-05-01

The amido-Schiff base 1 (N1, N3-bis (2-nitrobenzylidene)benzene-1,3-dicabohydrazide) containing a sbnd CONHsbnd group and sbnd CHdbnd Nsbnd linkage has been synthesized by the condensation between isophthalic acid dihydrazide and o-nitrobenzaldehyde. This molecule can act as a fluoride ion sensor with high selectivity and sensitivity. Presence of nitro group in the phenyl ring may be responsible for the detection of fluoride ion visually with a dramatic color change from colorless to deep red in aqueous dimethyl sulphoxide solution. This Schiff base can be used as test kit for sensing of fluoride ion in the solid state. Compound 1 can detect fluoride also in commercially available toothpaste. As the compound has adequate solubility in DMSO-water mixture (7:93, v/v) and having some hydrogen bond donor and acceptor centers, we have investigated its nature of binding with Calf Thymus-DNA (CT-DNA) using theoretical molecular modelling and other experimental methods like UV-vis spectroscopy, circular dichroic and thermal melting studies. Thermodynamic parameters have been obtained using the well known Van't Hoff's equation. From both theoretical and experimental findings it has been observed that it can interact effectively with CT-DNA with binding energy - 7.55 kcal/mol to - 7.50 kcal/mol.

Remediation of fluoride from drinking water using magnetic iron oxide coated hydrotalcite/chitosan composite.

PubMed

Pandi, Kalimuthu; Periyasamy, Soodamani; Viswanathan, Natrayasamy

2017-11-01

The present study was performed to examine the probability of magnetic iron oxide fabricated hydrotalcite/chitosan (Fe 3 O 4 @HTCS) composite for the removal of excess fluoride content from drinking water. The developed Fe 3 O 4 @HTCS composite not only demonstrate the good separation ability but also display an extreme enhanced defluoridation capacity (DC) when compared to other base components and composite. The DCs of Fe 3 O 4 @HTCS composite, Fe 3 O 4 @HT composite, Fe 3 O 4 , HT and CS was found to be 5032, 3041, 1050, 1030 and 52mgF - /kg respectively. The structure and morphology of the prepared adsorbent and fluoride sorbed adsorbent was analysed using FTIR, SEM and EDAX with mapping techniques. The dependence of DC on various parameters like initial fluoride concentration, pH, contact time, interfering anions and temperature was studied by batch method. From isotherm modeling, the equilibrium data is well described by Freundlich, Langmuir and Dubinin-Radushkevich (D-R) isotherms. Thermodynamic parameters confirm the spontaneity and endothermic nature of the fluoride adsorption. The performance of Fe 3 O 4 @HTCS composite to field water sample designates its adaptable nature at field conditions. Copyright © 2017 Elsevier B.V. All rights reserved.

Identification of cytochrome P450 2E1 as the predominant enzyme catalyzing human liver microsomal defluorination of sevoflurane, isoflurane, and methoxyflurane.

PubMed

Kharasch, E D; Thummel, K E

1993-10-01

Renal and hepatic toxicity of the fluorinated ether volatile anesthetics is caused by biotransformation to toxic metabolites. Metabolism also contributes significantly to the elimination pharmacokinetics of some volatile agents. Although innumerable studies have explored anesthetic metabolism in animals, there is little information on human volatile anesthetic metabolism with respect to comparative rates or the identity of the enzymes responsible for defluorination. The first purpose of this investigation was to compare the metabolism of the fluorinated ether anesthetics by human liver microsomes. The second purpose was to test the hypothesis that cytochrome P450 2E1 is the specific P450 isoform responsible for volatile anesthetic defluorination in humans. Microsomes were prepared from human livers. Anesthetic metabolism in microsomal incubations was measured by fluoride production. The strategy for evaluating the role of P450 2E1 in anesthetic defluorination involved three approaches: for a series of 12 human livers, correlation of microsomal defluorination rate with microsomal P450 2E1 content (measured by Western blot analysis), correlation of defluorination rate with microsomal P450 2E1 catalytic activity using marker substrates (para-nitrophenol hydroxylation and chlorzoxazone 6-hydroxylation), and chemical inhibition by P450 isoform-selective inhibitors. The rank order of anesthetic metabolism, assessed by fluoride production at saturating substrate concentrations, was methoxyflurane > sevoflurane > enflurane > isoflurane > desflurane > 0. There was a significant linear correlation of sevoflurane and methoxyflurane defluorination with antigenic P450 2E1 content (r = 0.98 and r = 0.72, respectively), but not with either P450 1A2 or P450 3A3/4. Comparison of anesthetic defluorination with either para-nitrophenol or chlorzoxazone hydroxylation showed a significant correlation for sevoflurane (r = 0.93, r = 0.95) and methoxyflurane (r = 0.78, r = 0.66). Sevoflurane defluorination was also highly correlated with that of enflurane (r = 0.93), which is known to be metabolized by human P450 2E1. Diethyldithiocarbamate, a selective inhibitor of P450 2E1, produced a concentration-dependent inhibition of sevoflurane, methoxyflurane, and isoflurane defluorination. No other isoform-selective inhibitor diminished the defluorination of sevoflurane, whereas methoxyflurane defluorination was inhibited by the selective P450 inhibitors furafylline (P450 1A2), sulfaphenazole (P450 2C9/10), and quinidine (P450 2D6) but to a much lesser extent than by diethyldithiocarbamate. These results demonstrate that cytochrome P450 2E1 is the principal, if not sole human liver microsomal enzyme catalyzing the defluorination of sevoflurane. P450 2E1 is the principal, but not exclusive enzyme responsible for the metabolism of methoxyflurane, which also appears to be catalyzed by P450s 1A2, 2C9/10, and 2D6. The data also suggest that P450 2E1 is responsible for a significant fraction of isoflurane metabolism. Identification of P450 2E1 as the major anesthetic metabolizing enzyme in humans provides a mechanistic understanding of clinical fluorinated ether anesthetic metabolism and toxicity.

Herbivore-induced blueberry volatiles and intra-plant signaling.

PubMed

Rodriguez-Saona, Cesar R

2011-12-18

Herbivore-induced plant volatiles (HIPVs) are commonly emitted from plants after herbivore attack. These HIPVs are mainly regulated by the defensive plant hormone jasmonic acid (JA) and its volatile derivative methyl jasmonate (MeJA). Over the past 3 decades researchers have documented that HIPVs can repel or attract herbivores, attract the natural enemies of herbivores, and in some cases they can induce or prime plant defenses prior to herbivore attack. In a recent paper, I reported that feeding by gypsy moth caterpillars, exogenous MeJA application, and mechanical damage induce the emissions of volatiles from blueberry plants, albeit differently. In addition, blueberry branches respond to HIPVs emitted from neighboring branches of the same plant by increasing the levels of JA and resistance to herbivores (i.e., direct plant defenses), and by priming volatile emissions (i.e., indirect plant defenses). Similar findings have been reported recently for sagebrush, poplar, and lima beans. Here, I describe a push-pull method for collecting blueberry volatiles induced by herbivore (gypsy moth) feeding, exogenous MeJA application, and mechanical damage. The volatile collection unit consists of a 4 L volatile collection chamber, a 2-piece guillotine, an air delivery system that purifies incoming air, and a vacuum system connected to a trap filled with Super-Q adsorbent to collect volatiles. Volatiles collected in Super-Q traps are eluted with dichloromethane and then separated and quantified using Gas Chromatography (GC). This volatile collection method was used in my study to investigate the volatile response of undamaged branches to exposure to volatiles from herbivore-damaged branches within blueberry plants. These methods are described here. Briefly, undamaged blueberry branches are exposed to HIPVs from neighboring branches within the same plant. Using the same techniques described above, volatiles emitted from branches after exposure to HIPVs are collected and analyzed.

Physiologic Conditions Affect Toxicity of Ingested Industrial Fluoride

PubMed Central

Sauerheber, Richard

2013-01-01

The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity from ingestion is distinct from fully soluble toxic industrial fluorides. The toxicity of fluoride is determined by environmental conditions and the positive cations present. At a pH typical of gastric juice, fluoride is largely protonated as hydrofluoric acid HF. Industrial fluoride ingested from treated water enters saliva at levels too low to affect dental caries. Blood levels during lifelong consumption can harm heart, bone, brain, and even developing teeth enamel. The widespread policy known as water fluoridation is discussed in light of these findings. PMID:23840230

Physiologic conditions affect toxicity of ingested industrial fluoride.

PubMed

Sauerheber, Richard

2013-01-01

The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity from ingestion is distinct from fully soluble toxic industrial fluorides. The toxicity of fluoride is determined by environmental conditions and the positive cations present. At a pH typical of gastric juice, fluoride is largely protonated as hydrofluoric acid HF. Industrial fluoride ingested from treated water enters saliva at levels too low to affect dental caries. Blood levels during lifelong consumption can harm heart, bone, brain, and even developing teeth enamel. The widespread policy known as water fluoridation is discussed in light of these findings.

21 CFR 177.2510 - Polyvinylidene fluoride resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Polyvinylidene fluoride resins. 177.2510 Section... Repeated Use § 177.2510 Polyvinylidene fluoride resins. Polyvinylidene fluoride resins may be safely used... fluoride resins consist of basic resins produced by the polymerization of vinylidene fluoride. (b) The...

Comparison of Antimicrobial Efficacy of Triclosan- Containing, Herbal and Homeopathy Toothpastes- An Invitro Study

PubMed Central

Fawaz, Mohammed Alimullah; Narahari, Rao; Shahela, Tanveer; Syed, Afroz

2015-01-01

Background Use of antimicrobial agents is one of the important strategies to prevent oral diseases. These agents vary in their abilities to deliver preventive and therapeutic benefits. Objectives This invitro study was conducted to assess antimicrobial efficacy of different toothpastes against various oral pathogens. Materials and Methods A total of nine toothpastes in three groups were tested for their antimicrobial activity against Escherichia coli (ATCC 25922), Staphylococcus aureus (ATCC 25923), Streptococcus mutans (ATCC 0266P) and Candida albicans (Laboratory Strain) by modified agar well diffusion method. Statistical Analysis was performed using Minitab Software. A p-value of less than 0.05 was considered significant. Results Triclosan-based dental formulation with combination of fluoride (1000ppm) exhibited higher antimicrobial activity against test organisms than the combination of lower fluoride-concentration or sodium monofluorophosphate. Among herbal dentifrices, formulation containing Neem, Pudina, Long, Babool, Turmeric and Vajradanti showed significant antimicrobial activity against all the four tested microorganisms (p<0.05). However, against Streptococcus mutans, all three herbal products showed significant antimicrobial activity. Homeo products showed least antimicrobial activity on the tested strains. Formulation with kreosotum, Plantago major and calendula was significantly effective only against Streptococcus mutans. Conclusion In the present study, antimicrobial activity of the toothpaste containing both triclosan and fluoride (1000ppm) as active ingredients showed a significant difference (p< 0.05) against all four tested microflora compared to that of with lower fluoride-concentration or sodium monofluorophosphate. Of herbal groups, the only dentifrice containing several phytochemicals was found to be significantly effective and comparable to triclosan-fluoride (1000ppm) formulation. Thus, this herbal toothpaste can be used as alternative to triclosan-based formulations. However, these results might not be clinically useful unless tested invivo. PMID:26557516

Magnetic Droplet Microfluidics as a Platform for the Concentration of [18F]Fluoride and Radiosynthesis of Sulfonyl [18F]Fluoride.

PubMed

Fiel, Somewhere A; Yang, Hua; Schaffer, Paul; Weng, Samuel; Inkster, James A H; Wong, Michael C K; Li, Paul C H

2015-06-17

The radioisotope 18F is often considered the best choice for positron emission tomography (PET) owing to its desirable chemical and radiochemical properties. However, nucleophilic 18F-fluorination of large, water-soluble biomolecules, based on C-F bond formation, has traditionally been difficult. Thus, several aqueous fluorination approaches that offer significant versatility in radiopharmaceutical synthesis with sensitive targeting vectors have been developed. Furthermore, because 18F decays rapidly, production of these 18F-labeled compounds requires an automated process to reduce production time, reduce radiation exposure, and minimize losses due to the transfer of reagents during tracer synthesis. Herein, we report the use of magnetic droplet microfluidics (MDM) as a means to concentrate [18F]fluoride from the cyclotron target solution, followed by the synthesis of an 18F-labeled compound on a microfluidic platform. Using this method, we have demonstrated 18F preconcentration in a small-volume droplet through the use of anion exchanging magnetic particles. By using MDM, the preconcentration step took approximately 5 min, and the [18F]fluoride solution was preconcentrated by 15-fold. After the preconcentration step, an 18F-labeling reaction was performed on the MDM platform using the S-F bond formation in aqueous conditions to produce an arylsulfonyl [18F]fluoride compound which can be used as a prosthetic group to label PET targeting ligands. The high radiochemical purity of 95±1% was comparable to the 96% previously reported using a conventional method. In addition, when MDM was used, the total synthesis time was improved to 15 min with lower reagent volumes (50-60 μL) used.

Comparison of in vitro fluoride uptake from whitening toothpastes and a conventional toothpaste in demineralised enamel.

PubMed

Altenburger, Markus J; Bernhart, Jasmin; Schicha, Thurid D; Wrbas, Karl-Thomas; Hellwig, Elmar

2010-01-01

Studies on the compatibility of abrasives and fluoride compounds deal exclusively with fluoride uptake and remineralization after storing the enamel specimens in a toothpaste-saliva mixture. The influence of brushing on the fluoride uptake when highly abrasive toothpastes are used has hardly been investigated so far. The aim of the present study was to investigate fluoride uptake in initially demineralised dental enamel after storage in, or brushing with, whitening toothpaste slurries, compared to a conventional toothpaste. For this purpose two widely available whitening toothpastes with ionically bound fluoride (sodium fluoride NaF), two with covalently-bound fluoride toothpastes (sodium monofluorophosphate, NaMFP) and a conventional amine fluoride toothpaste (AmF) were compared. The fluoride uptake after use of the AmF toothpaste was shown to be statistically significantly higher than that after application of the NaF toothpastes, which in turn was statistically significantly higher than the uptake resulting from NaMFP application. The fluoride uptake was slightly higher when the enamel samples were brushed with NaF toothpaste, rather than just stored in the respective toothpaste slurry. Brushing with highly abrasive toothpastes did not negatively influence fluoride uptake in demineralised dental enamel. The ionic form of the fluoride in toothpastes appears to be critical for increased fluoride uptake. The acidic components of the AmF toothpaste improved fluoride uptake compared to alkaline NaF toothpastes.

The effective use of fluorides in public health.

PubMed Central

Jones, Sheila; Burt, Brian A.; Petersen, Poul Erik; Lennon, Michael A.

2005-01-01

Dental caries remain a public health problem for many developing countries and for underprivileged populations in developed countries. This paper outlines the historical development of public health approaches to the use of fluoride and comments on their effectiveness. Early research and development was concerned with waterborne fluorides, both naturally occurring and added, and their effects on the prevalence and incidence of dental caries and dental fluorosis. In the latter half of the 20th century, the focus of research was on fluoride toothpastes and mouth rinses. More recently, systematic reviews summarizing these extensive databases have indicated that water fluoridation and fluoride toothpastes both substantially reduce the prevalence and incidence of dental caries. We present four case studies that illustrate the use of fluoride in modern public health practice, focusing on: recent water fluoridation schemes in California, USA; salt fluoridation in Jamaica; milk fluoridation in Chile; and the development of "affordable" fluoride toothpastes in Indonesia. Common themes are the concern to reduce demands for compliance with fluoride regimes that rely upon action by individuals and their families, and the issue of cost. We recommend that a community should use no more than one systemic fluoride (i.e. water or salt or milk fluoridation) combined with the use of fluoride toothpastes, and that the prevalence of dental fluorosis should be monitored in order to detect increases in or higher-than-acceptable levels. PMID:16211158

Solid state electrochemical current source

DOEpatents

Potanin, Alexander Arkadyevich; Vedeneev, Nikolai Ivanovich

2002-04-30

A cathode and a solid state electrochemical cell comprising said cathode, a solid anode and solid fluoride ion conducting electrolyte. The cathode comprises a metal oxide and a compound fluoride containing at least two metals with different valences. Representative compound fluorides include solid solutions of bismuth fluoride and potassium fluoride; and lead fluoride and potassium fluoride. Representative metal oxides include copper oxide, lead oxide, manganese oxide, vanadium oxide and silver oxide.

76 FR 37129 - Determination That SODIUM FLUORIDE F 18 (Sodium Fluoride F-18) Injection, 10 to 200 Millicuries...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-24

...] Determination That SODIUM FLUORIDE F 18 (Sodium Fluoride F-18) Injection, 10 to 200 Millicuries per Milliliter... FLUORIDE F 18 (sodium fluoride F-18) injection, 10 to 200 millicuries per milliliter (mCi/mL), was not... abbreviated new drug applications (ANDAs) for SODIUM FLUORIDE F 18 injection, 10 to 200 mCi/mL, if all other...

Process for converting magnesium fluoride to calcium fluoride

DOEpatents

Kreuzmann, A.B.; Palmer, D.A.

1984-12-21

This invention is a process for the conversion of magnesium fluoride to calcium fluoride whereby magnesium fluoride is decomposed by heating in the presence of calcium carbonate, calcium oxide or calcium hydroxide. Magnesium fluoride is a by-product of the reduction of uranium tetrafluoride to form uranium metal and has no known commercial use, thus its production creates a significant storage problem. The advantage of this invention is that the quality of calcium fluoride produced is sufficient to be used in the industrial manufacture of anhydrous hydrogen fluoride, steel mill flux or ceramic applications.

Health effects of groundwater fluoride contamination.

PubMed

Nayak, Bishwajit; Roy, Madan Mohan; Das, Bhaskar; Pal, Arup; Sengupta, Mrinal Kumar; De, Shankar Prasad; Chakraborti, Dipankar

2009-04-01

The people in Berhait block, Sahibganj district, Jharkhand state, India, have been exposed chronically to fluoridecontaminated groundwater. Hereby, we report the clinical effects of chronic exposure to fluoride. The study population was a convenience sample of 342 adults and 258 children living in the affected area. All volunteers filled out questionnaires and were examined. Well water from the six affected villages and urine samples were analyzed for fluoride using an ion-sensitive electrode. Twenty nine percent of 89 well water samples had fluoride concentrations above the Indian permissible limit of fluoride in drinking water. Eighty-five children and 72 adults had clinical fluorosis. Urine fluoride concentrations in children were 0.758-2.88 mg/L whereas in adults they were 0.331-10.36 mg/L. Clinical effects of fluoride included abnormal tooth enamel in children; adults had joint pain and deformity of the limbs and spine, along with ligamentous calcifications and exostosis formations in seven patients. Elevated urine fluoride concentrations supported the clinical diagnosis of fluorosis. Owing to insufficient fluoride-safe wells and lack of awareness of the danger of fluoride toxicity, villagers often drink fluoride-contaminated water. Villagers of Berhait block, including children, are at risk from chronic fluoride toxicity. To combat the situation, villagers need fluoride-safe water, education, and awareness of the danger about fluoride toxicity.

Preventive dentistry: practitioners' recommendations for low-risk patients compared with scientific evidence and practice guidelines.

PubMed

Frame, P S; Sawai, R; Bowen, W H; Meyerowitz, C

2000-02-01

The purpose of this article is to compare published evidence supporting procedures to prevent dental caries and periodontal disease, in low-risk patients, with the actual preventive recommendations of practicing dentists. Methods included (1) a survey questionnaire of general dentists practicing in western New York State concerning the preventive procedures they would recommend and at what intervals for low-risk children, young adults, and older adults; and (2) review of the published, English-language literature for evidence supporting preventive dental interventions. The majority of dentists surveyed recommended semiannual visits for visual examination and probing to detect caries (73% to 79%), and scaling and polishing to prevent periodontal disease (83% to 86%) for low-risk patients of all ages. Bite-wing radiographs were recommended for all age groups at annual or semiannual intervals. In-office fluoride applications were recommended for low-risk children at intervals of 6 to 12 months by 73% of dentists but were recommended for low-risk older persons by only 22% of dentists. Application of sealants to prevent pit and fissure caries was recommended for low-risk children by 22% of dentists. Literature review found no studies comparing different frequencies of dental examinations and bite-wing radiographs to determine the optimal screening interval in low-risk patients. Two studies of the effect of scaling and polishing on the prevention of periodontal disease found no benefit from more frequent than annual treatments. Although fluoride is clearly a major reason for the decline in the prevalence of dental caries, there are no studies of the incremental benefit of in-office fluoride treatments for low-risk patients exposed to fluoridated water and using fluoridated toothpaste. Comparative studies using outcome end points are needed to determine the optimal frequency of dental examinations and bite-wing radiographs for the early detection of caries, and of scaling and polishing to prevent periodontal disease in low-risk persons. There is no scientific evidence that dental examinations, including scaling and polishing, at 6 month intervals, as recommended by the dentists surveyed in this study, is superior to annual or less frequent examinations for low-risk populations. There is also no evidence that in-office fluoride applications offer incremental benefit over less costly methods of delivering fluoride for low-risk populations.

Appropriate uses of fluorides for children: guidelines from the Canadian Workshop on the Evaluation of Current Recommendations Concerning Fluorides.

PubMed Central

Clark, D C

1993-01-01

OBJECTIVE: To prevent fluorosis caused by excessive fluoride ingestion by revising recommendations for fluoride intake by children. OPTIONS: Limiting fluoride ingestion from fluoridated water, fluoride supplements and fluoride dentifrices. OUTCOMES: Reduction in the prevalence of dental fluorosis and continued prevention of dental caries. EVIDENCE: Before the workshop, experts prepared comprehensive literature reviews of fluoride therapies, fluoride ingestion and the prevalence and causes of dental fluorosis. The papers, which were peer-reviewed, revised and circulated to the workshop participants, formed the basis of the workshop discussions. VALUES: Recommendations to limit fluoride intake were vigorously debated before being adopted as the consensus opinion of the workshop group. BENEFITS, HARMS AND COSTS: Decrease in the prevalence of dental fluorosis with continuing preventive effects of fluoride use. The only significant cost would be in preparing new, low-concentration fluoride products for distribution. RECOMMENDATIONS: Fluoride supplementation should be limited to children 3 years of age and older in areas where there is less than 0.3 ppm of fluoride in the water supply. Children in all areas should use only a "pea-sized" amount of fluoride dentifrice no more than twice daily under the supervision of an adult. VALIDATION: These recommendations are almost identical to changes to recommendations for the use of fluoride supplements recently proposed by a group of European countries. SPONSORS: The workshop was organized by Dr. D. Christopher Clark, of the University of British Columbia, and Drs. Hardy Limeback and Ralph C. Burgess, of the University of Toronto, and funded by Proctor and Gamble Inc., Toronto, the Medical Research Council of Canada and Health Canada (formerly the Department of National Health and Welfare). The recommendations were formally adopted by the Canadian Dental Association in April 1993. PMID:8261348

Review on fluoride-releasing restorative materials--fluoride release and uptake characteristics, antibacterial activity and influence on caries formation.

PubMed

Wiegand, Annette; Buchalla, Wolfgang; Attin, Thomas

2007-03-01

The purpose of this article was to review the fluoride release and recharge capabilities, and antibacterial properties, of fluoride-releasing dental restoratives, and discuss the current status concerning the prevention or inhibition of caries development and progression. Information from original scientific full papers or reviews listed in PubMed (search term: fluoride release AND (restorative OR glass-ionomer OR compomer OR polyacid-modified composite resin OR composite OR amalgam)), published from 1980 to 2004, was included in the review. Papers dealing with endodontic or orthodontic topics were not taken into consideration. Clinical studies concerning secondary caries development were only included when performed in split-mouth design with an observation period of at least three years. Fluoride-containing dental materials show clear differences in the fluoride release and uptake characteristics. Short- and long-term fluoride releases from restoratives are related to their matrices, setting mechanisms and fluoride content and depend on several environmental conditions. Fluoride-releasing materials may act as a fluoride reservoir and may increase the fluoride level in saliva, plaque and dental hard tissues. However, clinical studies exhibited conflicting data as to whether or not these materials significantly prevent or inhibit secondary caries and affect the growth of caries-associated bacteria compared to non-fluoridated restoratives. Fluoride release and uptake characteristics depend on the matrices, fillers and fluoride content as well as on the setting mechanisms and environmental conditions of the restoratives. Fluoride-releasing materials, predominantly glass-ionomers and compomers, did show cariostatic properties and may affect bacterial metabolism under simulated cariogenic conditions in vitro. However, it is not proven by prospective clinical studies whether the incidence of secondary caries can be significantly reduced by the fluoride release of restorative materials.

FLUORIDE CONTENT OF COMMERCIALLY AVAILABLE BOTTLED DRINKING WATER IN BANGKOK, THAILAND.

PubMed

Rirattanapong, Praphasri; Rirattanapong, Opas

2016-09-01

The use of bottled drinking water may be a source of fluoride and could be a risk factor for fluorosis among infants and young children. The aim of this study was to evaluate the fluoride content of commercially available bottled drinking water in Bangkok, Thailand. Forty-five water samples (15 samples of plain water and 30 samples of mineral water) were purchased from several supermarkets in Bangkok, Thailand. Three bottles of each water sample were purchased, and the fluoride content of each sample was measured twice using a combination fluoride-ion selective electrode. The average reading for each sample was then calculated. Data were analyzed by descriptive statistics. Differences between mineral and plain water samples were determined by Student’s t-test. The mean (±SD) fluoride content for all the water samples was 0.17 (±0.17) mg F/l (range: 0.01-0.89 mg F/l). Six brands (13%) tested stated the fluoride content on the label. The actual fluoride content in each of their brands varied little from the label. Eight samples (18%) had a fluoride content >0.3 mg F/l and two samples (4%) had a fluoride content >0.6 mg F/l. The mean mineral water fluoride concentration was significantly higher than the mean fluoride concentration of plain water (p=0.001). We found commercially sold bottled drinking water in Bangkok, Thailand contained varying concentrations of fluoride; some with high concentrations of fluoride. Health professions need to be aware this varying fluoride content of bottled drinking water and educate the parents of infants and small children about this when prescribing fluoride supplements. Consideration should be made to have fluoride content put on the label of bottled water especially among brands with a content >0.3 mg F/l.

[Estimation of exposure to fluoride in "Los Altos de Jalisco", México].

PubMed

Hurtado-Jiménez, Roberto; Gardea-Torresdey, Jorge

2005-01-01

To estimate the level of fluoride exposure and human health risks in Los Altos de Jalisco (Jalisco State Heights) region. This study was conducted between May and July 2002. The fluoride concentrations of 105 water wells and six tap water samples were electrochemically measured. Exposure doses to fluoride and total intake of fluoride were estimated for babies (10 kg), children (20 kg), and adults (70 kg). The fluoride concentration of the water samples ranged from 0.1 to 17.7 mg/l. More than 45% of the water samples exceeded the national guideline value for fluoride of 1.5 mg/l. The estimated values of the exposure doses to fluoride and total intake of fluoride were in the range of 0.04-1.8 mg/kg/d and 0.5-18.4 mg/d, respectively. Dental fluorosis, skeletal fluorosis, and bone fractures are some of the potential health risks due to the intake of high doses of fluoride for the population of Los Altos de Jalisco. In order to reduce health risks, fluoridated salt,fluoridated toothpastes, and drinking water containing more than 0.7 mg/l of fluoride should be avoided.

Fluoride in the environment and its metabolism in humans.

PubMed

Jha, Sunil Kumar; Mishra, Vinay Kumar; Sharma, Dinesh Kumar; Damodaran, Thukkaram

2011-01-01

The presence of environmental fluoride and its impact on human health is well documented. When consumed in adequate quantity, fluoride prevents dental caries, assists in the formation of dental enamels, and prevents deficiencies in bone mineralization. At excessive exposure levels, ingestion of fluoride causes dental fluorosis skeletal fluorosis, and manifestations such as gastrointestinal, neurological, and urinary problems. The distribution of fluoride in the environment is uneven and largely is believed to derive from geogenic causes. The natural sources of fluoride are fluorite, fluorapatite, and cryolite, whereas anthropogenic sources include coal burning, oil refining, steel production, brick-making industries, and phosphatic fertilizer plants, among others. Among the various sources of fluoride in the environment, those of anthropogenic origin have occasionally been considered to be major ones. The gourndwater is more susceptible to fluoride accumulation and contamination than are other environmental media, primarily because of its contact with geological substrates underneath. The high fluoride concentration in water usually reflects the solubility of fluoride (CaF₂). High concentrations are also often associated with soft, alkaline, and calcium-deficient waters. The fluoride compounds that occur naturally in drinking water are almost totally bioavailable (90%) and are completely absorbed from the gastrointestinal tract. As a result, drinking water is considered to be the potential source of fluoride that causes fluorosis. Because the bioavailability of fluoride is generally reduced in humans when consumed with milk or a calcium-rich diet, it is highly recommended that the inhabitants of fluoride-contaminated areas should incorporate calcium-rich foods in their routine diet. Guidelines for limiting the fluoride intake from drinking water have been postulated by various authorities. Such limits are designed to protect public health and should reflect all fluoride intake sources, including dietary fluoride. The toxicological risks posed by fluoride could be better understood if epidemiological surveillance for dental and skeletal fluorosis would be systematically conducted in fluoride-affected areas. Such input would greatly improve understanding of the human dose-response relationship. Such surveillance of potentially high fluoride areas is also important because it would help to delineate, much earlier, the remedial measures that are appropriate for those areas.

Potential fluoride toxicity from oral medicaments: A review.

PubMed

Ullah, Rizwan; Zafar, Muhammad Sohail; Shahani, Nazish

2017-08-01

The beneficial effects of fluoride on human oral health are well studied. There are numerous studies demonstrating that a small amount of fluoride delivered to the oral cavity decreases the prevalence of dental decay and results in stronger teeth and bones. However, ingestion of fluoride more than the recommended limit leads to toxicity and adverse effects. In order to update our understanding of fluoride and its potential toxicity, we have described the mechanisms of fluoride metabolism, toxic effects, and management of fluoride toxicity. The main aim of this review is to highlight the potential adverse effects of fluoride overdose and poorly understood toxicity. In addition, the related clinical significance of fluoride overdose and toxicity has been discussed.

DISSOLUTION OF ZIRCONIUM AND ALLOYS THEREFOR

DOEpatents

Swanson, J.L.

1961-07-11

The dissolution of zirconium cladding in a water solution of ammonium fluoride and ammonium nitrate is described. The method finds particular utility in processing spent fuel elements for nuclear reactors. The zirconium cladding is first dissolved in a water solution of ammonium fluoride and ammonium nitrate; insoluble uranium and plutonium fiuorides formed by attack of the solvent on the fuel materiai of the fuel element are then separated from the solution, and the fuel materiai is dissolved in another solution.

Separation of Californium from other Actinides

DOEpatents

Mailen, J C; Ferris, L M

1973-09-25

A method is provided for separating californium from a fused fluoride composition containing californium and at least one element selected from the group consisting of plutonium, americium, curium, uranium, thorium, and protactinium which comprises contacting said fluoride composition with a liquid bismuth phase containing sufficient lithium or thorium to effect transfer of said actinides to the bismuth phase and then contacting the liquid bismuth phase with molten LiCl to effect selective transfer of californium to the chloride phase.

Hydroxyapatite, fluor-hydroxyapatite and fluorapatite produced via the sol-gel method: dissolution behaviour and biological properties after crystallisation.

PubMed

Tredwin, Christopher J; Young, Anne M; Abou Neel, Ensanya A; Georgiou, George; Knowles, Jonathan C

2014-01-01

Hydroxyapatite (HA), fluor-hydroxyapatite (FHA) with varying levels of fluoride ion substitution and fluorapatite (FA) were synthesised by the sol-gel method as possible implant coating or bone-grafting materials. Calcium nitrate and triethyl phosphite were used as precursors under an ethanol-water based solution. Different amounts of ammonium fluoride were incorporated for the preparation of the FHA and FA sol-gels. After heating and powdering the sol-gels, dissolution behaviour was assessed using ion chromatography to measure Ca(2+) and PO4 (3-) ion release. Biological behaviour was assessed using cellular proliferation with human osteosarcoma cells and alamarBlue™ assay. Statistical analysis was performed with a two way analysis of variance and post hoc testing with a Bonferroni correction. Increasing fluoride substitution into an apatite structure decreased the dissolution rate. Increasing the firing temperature of the HA, FHA and FA sol-gels up to 1,000 °C decreased the dissolution rate. There was significantly higher cellular proliferation on highly substituted FHA and FA than on HA or Titanium. The properties of an implant coating or bone grafting material can be tailored to meet specific requirements by altering the amount of fluoride that is incorporated into the original apatite structure. The dissolution behaviour can further be altered by the temperature at which the sol-gel is fired.

Ab Initio Calculations of Anharmonic Vibrational Spectroscopy for Hydrogen Fluoride (HF)n (n=3,4) and Mixed Hydrogen Fluoride/Water (HF)n(H20)n (n=1,2,4) Clusters

NASA Technical Reports Server (NTRS)

Chaban, Galina M.; Gerber, R. Benny; Kwak, Dochan (Technical Monitor)

2001-01-01

Anharmonic vibrational frequencies and intensities are computed for hydrogen fluoride clusters (HF)n with n=3,4 and mixed clusters of hydrogen fluoride with water (HF)n(H2O)n where n=1,2. For the (HF)4(H2O)4 complex, the vibrational spectra are calculated at the harmonic level, and anharmonic effects are estimated. Potential energy surfaces for these systems are obtained at the MP2/TZP level of electronic structure theory. Vibrational states are calculated from the potential surface points using the correlation-corrected vibrational self-consistent field (CC-VSCF) method. The method accounts for the anharmonicities and couplings between all vibrational modes and provides fairly accurate anharmonic vibrational spectra that can be directly compared with experimental results without a need for empirical scaling. For (HF)n, good agreement is found with experimental data. This agreement shows that the MP2 potential surfaces for these systems are reasonably reliable. The accuracy is best for the stiff intramolecular modes, which indicates the validity of MP2 in describing coupling between intramolecular and intermolecular degrees of freedom. For (HF)n(H2O)n experimental results are unavailable. The computed intramolecular frequencies show a strong dependence on cluster size. Intensity features are predicted for future experiments.

Ab initio calculations of anharmonic vibrational spectroscopy for hydrogen fluoride (HF)n (n = 3, 4) and mixed hydrogen fluoride/water (HF)n(H2O)n (n = 1, 2, 4) clusters

NASA Technical Reports Server (NTRS)

Chaban, Galina M.; Gerber, R. Benny

2002-01-01

Anharmonic vibrational frequencies and intensities are computed for hydrogen fluoride clusters (HF)n, with n = 3, 4 and mixed clusters of hydrogen fluoride with water (HF)n(H2O)n where n = 1, 2. For the (HF)4(H2O)4 complex, the vibrational spectra are calculated at the harmonic level, and anharmonic effects are estimated. Potential energy surfaces for these systems are obtained at the MP2/TZP level of electronic structure theory. Vibrational states are calculated from the potential surface points using the correlation-corrected vibrational self-consistent field method. The method accounts for the anharmonicities and couplings between all vibrational modes and provides fairly accurate anharmonic vibrational spectra that can be directly compared with experimental results without a need for empirical scaling. For (HF)n, good agreement is found with experimental data. This agreement shows that the Moller-Plesset (MP2) potential surfaces for these systems are reasonably reliable. The accuracy is best for the stiff intramolecular modes, which indicates the validity of MP2 in describing coupling between intramolecular and intermolecular degrees of freedom. For (HF)n(H2O)n experimental results are unavailable. The computed intramolecular frequencies show a strong dependence on cluster size. Intensity features are predicted for future experiments.

Loss on drying, calcium concentration and pH of fluoride dentifrices

PubMed Central

Brito, Arella Cristina Muniz; Dantas, Lívia Rocha; De Brito, André Luiz Fiquene; Muniz, Ana Cristina Silva; Ramos, Ianny Alves; Cardoso, Andreia Medeiros Rodrigues; Xavier, Alidianne Fábia Cabral; Cavalcanti, Alessandro Leite

2015-01-01

Introduction: Fluoride dentifrices containing calcium carbonate have advantages such as control of dental plaque and progression of dental caries, also contributing to oral hygiene, represent most dentifrices marketed in Brazil. Aim: To evaluate the physicochemical properties of seven fluoride dentifrices containing calcium carbonate in relation to hydrogen potential (pH), loss on drying and calcium concentration. Materials and Methods: Data collection was performed using the potentiometric method for pH ranges, gravimetric analysis for loss on drying and atomic absorption spectrometry for the concentration of calcium ions. All tests were performed in triplicate and the analysis was performed entirely at random according to one-way analysis of variance at 5% significance level. Results: The pH values were alkaline and ranged from 8.67 (Oral-B 123®) to 10.03 (Colgate Máxima Proteção Anticáries®). The results of loss on drying ranged from 33.81% (Oral-B 123®) to 61.13% (Close Up®), with significant differences between brands tested. In relation to the calcium content, the highest and lowest concentrations were found in dentifrices Even® (155.55 g/kg) and Colgate Ultra Branco® (129 g/kg), respectively, with significant difference (P < 0.05). Conclusion: Fluoride dentifrices analyzed showed alkaline pH and high levels of loss on drying and calcium concentration. However, these physicochemical characteristics differed according to the different brands tested. PMID:25821380

Method for fluorination of actinide fluorides and oxyfluorides using O/sub 2/F/sub 2/

DOEpatents

Eller, P.G.; Malm, J.G.; Penneman, R.A.

1984-08-01

The present invention relates generally to methods of fluorination and more particularly to the use of O/sub 2/F/sub 2/ for the preparation of actinide hexafluorides, and for the extraction of deposited actinides and fluorides and oxyfluorides thereof from reaction vessels. The experiments set forth hereinabove demonstrate that the room temperature or below use of O/sub 2/F/sub 2/ will be highly beneficial for the preparation of pure actinide hexafluorides from their respective tetrafluorides without traces of HF being present as occurs using other fluorinating agents: and decontamination of equipment previously exposed to actinides: e.g., walls, feed lines, etc.

Vapor-liquid equilibria for hydrogen fluoride + 1,1-difluoroethane at 288.23 and 298.35 K

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, J.; Kim, H.; Lim, J.S.

1997-07-01

Isothermal vapor-liquid equilibria for hydrogen fluoride + 1,1-difluoroethane at 288.23 and 298.35 K were measured using a circulation type apparatus equipped with an equilibrium view cell. The compositions of both vapor and liquid phases were analyzed by an on-line gas chromatographic method. They were compared with PTx equilibrium data measured by the total pressure method. The experimental data were correlated with Anderko`s equation of state using the Wong-Sandler mixing rule as well as the van der Waals one-fluid mixing rule. The Wong-Sandler mixing rule gives better results, and the relevant parameters are presented.

Thirty years of fluoridation: a review.

PubMed

Richmond, V L

1985-01-01

Fluoride contributes to stability of both teeth and bones and to reduction of caries, especially if ingested before eruption of teeth. Reduction of caries continues at about 60% in persons drinking fluoridated water only as long as fluoride washes over teeth. One-half the population of the US does not have access to water with an optimal fluoride concentration of about 1 mg/L. Misinformation about fluoridation contributes to reluctance of communities to supplement the natural but inadequate fluoride of those water supplies. Fluoridation of water has no positive or negative effect on incidence or mortality rates due to cancer, heart disease, intracranial lesions, nephritis, cirrhosis, mongoloid births, or from all causes together. The collective decision to increase the natural fluoride content of water supplies is not an infringement of civil rights, nor does it establish a precedent in the binding sense of the law. Supplemental fluoride in water makes it available to all members of the community in a safe, practical, economical and reliable manner. Fluoridation saves money in dental costs and time lost from work. Fluoridation is an appropriate action of government in promoting the health and welfare of society.

Fluoride in groundwater: toxicological exposure and remedies.

PubMed

Jha, S K; Singh, R K; Damodaran, T; Mishra, V K; Sharma, D K; Rai, Deepak

2013-01-01

Fluoride is a chemical element that is found most frequently in groundwater and has become one of the most important toxicological environmental hazards globally. The occurrence of fluoride in groundwater is due to weathering and leaching of fluoride-bearing minerals from rocks and sediments. Fluoride when ingested in small quantities (<0.5 mg/L) is beneficial in promoting dental health by reducing dental caries, whereas higher concentrations (>1.5 mg/L) may cause fluorosis. It is estimated that about 200 million people, from among 25 nations the world over, may suffer from fluorosis and the causes have been ascribed to fluoride contamination in groundwater including India. High fluoride occurrence in groundwaters is expected from sodium bicarbonate-type water, which is calcium deficient. The alkalinity of water also helps in mobilizing fluoride from fluorite (CaF2). Fluoride exposure in humans is related to (1) fluoride concentration in drinking water, (2) duration of consumption, and (3) climate of the area. In hotter climates where water consumption is greater, exposure doses of fluoride need to be modified based on mean fluoride intake. Various cost-effective and simple procedures for water defluoridation techniques are already known, but the benefits of such techniques have not reached the rural affected population due to limitations. Therefore, there is a need to develop workable strategies to provide fluoride-safe drinking water to rural communities. The study investigated the geochemistry and occurrence of fluoride and its contamination in groundwater, human exposure, various adverse health effects, and possible remedial measures from fluoride toxicity effects.

Evaluation of adhesive-free crossed-electrode poly(vinylidene fluoride) copolymer array transducers for high frequency imaging

NASA Astrophysics Data System (ADS)

Wagle, Sanat; Decharat, Adit; Habib, Anowarul; Ahluwalia, Balpreet S.; Melandsø, Frank

2016-07-01

High frequency crossed-electrode transducers have been investigated, both as single and dual layer transducers. Prototypes of these transducers were developed for 4 crossed lines (yielding 16 square elements) on a polymer substrate, using a layer-by-layer deposition method for poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] with intermediate sputtered electrodes. The transducer was characterized using various methods [LCR analyzer, a pulse-echo experimental setup, and a numerical Finite element method (FEM) model] and evaluated in terms of uniformity of bandwidth and acoustical energy output. All 16 transducer elements produced broad-banded ultrasonic spectra with small variation in central frequency and -6 dB bandwidth. The frequency responses obtained experimentally were verified using a numerical model.

A novel ultrasonication method in the preparation of zirconium impregnated cellulose for effective fluoride adsorption.

PubMed

Barathi, M; Kumar, A Santhana Krishna; Rajesh, N

2014-05-01

In the present work, we propose for the first time a novel ultrasound assisted methodology involving the impregnation of zirconium in a cellulose matrix. Fluoride from aqueous solution interacts with the cellulose hydroxyl groups and the cationic zirconium hydroxide. Ultrasonication ensures a green and quick alternative to the conventional time intensive method of preparation. The effectiveness of this process was confirmed by comprehensive characterization of zirconium impregnated cellulose (ZrIC) adsorbent using Fourier transform infrared spectroscopy (FT-IR), energy dispersive X-ray spectrometry (EDX) and X-ray diffraction (XRD) studies. The study of various adsorption isotherm models, kinetics and thermodynamics of the interaction validated the method. Copyright © 2013 Elsevier B.V. All rights reserved.

Fluoride content of infant formulas prepared with deionized, bottled mineral and fluoridated drinking water.

PubMed

Buzalaf, M A; Granjeiro, J M; Damante, C A; de Ornelas, F

2001-01-01

Usually infant milk formula is the major source of fluoride in infancy. Fluoride concentrations in ten samples of powdered milk formulas, prepared with deionized, bottled mineral, and fluoridated drinking water were determined after HMDS-facilitated diffusion, using a fluoride ion specific electrode(Orion 9609). Fluoride concentrations ranged from 0.01 to 0.75 ppm; from 0.02 to 1.37 ppm and from 0.91 to 1.65 ppm for formulas prepared with deionized, bottled mineral (0.02 to 0.69 ppm F) and fluorinated drinking water (0.9 ppm F), respectively. Possible fluoride ingestion per Kg body mass ws estimated. With deionized water, only the soy-based- formulas should provide a daily fluoride intake of above the suggested threshold for fluorosis. With water containing 0.9 ppm F, however, all of them would provide it. Hence, to limit fluoride intakes to amounts <0.1 mg/kg/day, it is necessary to avoid use fo fluoridated water (around 1 ppm) to dilute powdered infant formulas.

The fractional urinary fluoride excretion of adults consuming naturally and artificially fluoridated water and the influence of water hardness: a randomized trial.

PubMed

Villa, A; Cabezas, L; Anabalón, M; Rugg-Gunn, A

2009-09-01

To assess whether there was any significant difference in the average fractional urinary fluoride excretion (FUFE) values among adults consuming (NaF) fluoridated Ca-free water (reference water), naturally fluoridated hard water and an artificially (H2SiF6) fluoridated soft water. Sixty adult females (N=20 for each treatment) participated in this randomized, double-blind trial. The experimental design of this study provided an indirect estimation of the fluoride absorption in different types of water through the assessment of the fractional urinary fluoride excretion of volunteers. Average daily FUFE values (daily amount of fluoride excreted in urine/daily total fluoride intake) were not significantly different between the three treatments (Kruskal-Wallis; p = 0.62). The average 24-hour FUFE value (n=60) was 0.69; 95% C.I. 0.65-0.73. The results of this study suggest that the absorption of fluoride is not affected by water hardness.

Does fluoride in the water close the dental caries gap between Indigenous and non-Indigenous children?

PubMed

Lalloo, R; Jamieson, L M; Ha, D; Ellershaw, A; Luzzi, L

2015-09-01

Indigenous children experience significantly more dental caries than non-Indigenous children. This study assessed if access to fluoride in the water closed the gap in dental caries between Indigenous and non-Indigenous children. Data from four states and two territories were sourced from the Child Dental Health Survey (CDHS) conducted in 2010. The outcomes were dental caries in the deciduous and permanent dentitions, and the explanatory variables were Indigenous status and access to fluoridated water (≥0.5 mg/L) prior to 2008. Dental caries prevalence and severity for Indigenous and non-Indigenous children, in both dentitions, was lower in fluoridated areas compared to non-fluoridated areas. Among non-Indigenous children, there was a 50.9% difference in mean dmft scores in fluoridated (1.70) compared to non-fluoridated (2.86) areas. The difference between Indigenous children in fluoridated (3.29) compared to non-fluoridated (4.16) areas was 23.4%. Among non-Indigenous children there was a 79.7% difference in the mean DMFT scores in fluoridated (0.68) compared to non-fluoridated (1.58) areas. The difference between Indigenous children in fluoridated (1.59) and non-fluoridated (2.23) areas was 33.5%. Water fluoridation is effective in reducing dental caries, but does not appear to close the gap between non-Indigenous children and Indigenous children. © 2015 Australian Dental Association.

Characteristics of epidemiology of dental caries in children from regions with high and optimum fluorine content in drinking water.

PubMed

Trufanova, Valentina; Sheshukova, Olha; Davydenko, Vadym; Polishchuk, Tetiana; Bauman, Sofia; Dobroskok, Vitalina

2018-01-01

Introduction: Prevention of dental diseases in children is the priority item on the modern dentistry agenda. Among the undeniable factors known as contributing into caries incidence, there is fluoride content in the external environment, especially in drinking water, which is the main source of fluoride intake. The aim: This study is aimed at evaluating dental caries indices in children and adolescents inhabiting in areas with optimal and high-level fluoride concentration in drinking water and assessing their level of oral hygiene. Materials and methods: To explore the caries epidemiology in the regions with optimal and high fluoride content, we examined 315 children aged 6, 12 and 15 who live in the city of Poltava (fluoride content in drinking water is 0.9-1.2 mg / l) and 91 children of the same age residing in the village of a town type Mashivka (fluoride content in drinking water ranges from 1.7 to 2.9 mg / l). Results: More than half of the 6-year-old children of both groups have decayed teeth. The comparative analysis of the prevalence and intensity of caries in the children aged 12 and 15 years demonstrated a significant increase in the number of individuals diagnosed to have caries with increasing age in both groups. Conclusions: Our research suggests that, along with the number of other cariogenic factors, fluorosis contributes to a more intense course of caries progression. This situation demands wider health policy measures to support primary and secondary caries prevention and management among the children.

Gramicidin D enhances the antibacterial activity of fluoride.

PubMed

Nelson, James W; Zhou, Zhiyuan; Breaker, Ronald R

2014-07-01

Fluoride is a toxic anion found in many natural environments. One of the major bacterial defenses against fluoride is the cell envelope, which limits passage of the membrane-impermeant fluoride anion. Accordingly, compounds that enhance the permeability of bacterial membranes to fluoride should also enhance fluoride toxicity. In this study, we demonstrate that the pore-forming antibiotic gramicidin D increases fluoride uptake in Bacillus subtilis and that the antibacterial activity of this compound is potentiated by fluoride. Polymyxin B, another membrane-targeting antibiotic with a different mechanism of action, shows no such improvement. These results, along with previous findings, indicate that certain compounds that destabilize bacterial cell envelopes can enhance the toxicity of fluoride. Copyright © 2014 Elsevier Ltd. All rights reserved.

METHODS DEVELOPMENT AND DEMONSTRATION FOR ASSESSING LEVEL OF NATIVE PESTICIDES, PCBS, PAHS, AND VOCS IN HUMAN BLOOD

EPA Science Inventory

Methods have been developed for screening and assessing the level of volatile, semi-volatile and non-volatile organic pollutants in human blood. The specific methodology is developed for measuring the presence of "native" compounds rather than their metabolites. Spe...

Fluoride and sulfur dioxide indoor pollution situation and control in coal-burning endemic area in Zhaotong, Yunnan, China

NASA Astrophysics Data System (ADS)

Liu, Yonglin; Luo, Kunli; Li, Ling; Shahid, Muhammad Zeeshaan

2013-10-01

The presented study aims to investigate the gaseous fluoride and sulfur dioxide (SO2) pollution level in the kitchen, traditional flue-curing barn and outdoor environment and to find economically feasible method to reduce fluorine and sulfur release. The gaseous fluoride and SO2 concentrations in air of outdoor environment, kitchen and traditional flue-curing barn were determined in 56 households in coal-burning endemic fluorosis areas of Zhaotong. Among these, 21 households in Yujiawan Village, Zhenxiong County, Zhaotong City were chosen for this experiment to reduce gaseous fluoride and SO2 concentration in traditional flue-curing barn air by using calcined dolomitic siliceous limestone (CDSL) instead of clay mixed with coal. The result showed that: (1) gaseous fluoride and SO2 concentration in the outdoor air in Mangbu Township area was 0.51 μg dm-2ṡday and <0.05 mg m-3, respectively and in Xiaolongdong Township was 2.7 μg dm-2 day and <0.05 mg m-3, respectively while in Zhaotong City these concentration were lower than the ambient air standard (3 μg dm-2ṡday and 0.5 mg m-3, respectively). (2) The indoor gaseous fluoride concentration (3.7 μg m-3) in air of kitchen with the improved coal stove was within the reference value (10 μg m-3); SO2 concentration (0.94 mg m-3) in kitchen air had decline, but its concentration was still higher than indoor air quality standard (0.5 mg m-3). (3) Average concentration of gaseous fluoride and SO2 in air of traditional flue-curing barn of Xiaolongdong Township was 7.2 μg m-3 and 6.8 mg m-3 respectively, and in Yujiawan village were 10.1 μg m-3 and 14.4 mg m-3, respectively. (4) After using the calcined dolomitic siliceous limestone instead of clay mixed with coal, gaseous fluoride and SO2 concentration in the traditional flue-curing barn air decreased of 45% and 91%, respectively. The gaseous fluoride and SO2 pollution in the traditional flue-curing barn is very serious. The corn and chili baked by open stoves in traditional flue-curing barn (baking room) was also seriously polluted by fluoride and sulfur. After using the calcined dolomitic siliceous limestone instead of clay mixed with coal, gaseous fluoride and SO2 concentration in the traditional flue-curing barn air have declined markedly. The way of adding calcined dolomitic siliceous limestone instead of clay as a binder for briquette-making is an economically feasible way to control the indoor pollution of fluorine and sulfur in coal-burning endemic in Zhaotong, Yunnan.