The Effect of Spray Strips on the Take-off Performance of a Model of a Flying-Boat Hull

NASA Technical Reports Server (NTRS)

Truscott, Starr

1935-01-01

The effect on the take-off performance of a model of the hull of a typical flying boat, Navy PH-1, of fitting spray strips of four different widths, each at three different angles, was determined by model tests in the NACA Tank. Spray strips of widths up to 3 percent of the beam improve the general performance at speeds near the hump and reduce the spray thrown. A downward angle of 30 degrees to 45 degrees in the neighborhood of the step seems most favorable for the reduction of the spray. The spray strips have a large effect in reducing the trimming moments at speeds near the hump speed, but have little effect on them at high speeds.

Response of Olive Fruit Fly (Diptera: Tephritidae) to an Attract-and-Kill Trap in Greenhouse Cage Tests

PubMed Central

Yokoyama, Victoria Y.

2014-01-01

Abstract A novel attract-and-kill trap for olive fruit fly, Bactrocera oleae (Rossi) (Diptera: Tephritidae), was constructed with yellow corrugated plastic in an inverted cylindrical pan shape formed from a disk and collar. The trap components were tested under three greenhouse temperatures and humidities of warm, hot, and very hot for attractiveness to caged young or older adults. A greater proportion of adults regardless of age were found underneath the devices including disks, cylindrical pans, and pans with pheromone lures and test units of cylindrical pans sprayed with water, insecticidal bait spray, and with lures. The effect was related to lower temperatures on the underside compared with the top and the intolerance of the pest to heat. A circular collar added to the perimeter of the disk that formed the top of the inverted cylinder made the attract-and-kill trap more attractive to adults than the disk alone. Pheromone lures or bait sprays did not increase adult attraction, so were not needed for efficacy. The cylindrical pan was especially attractive to adults when temperatures were high by providing shelter from the heat. At very high temperatures, the pan became unattractive, possibly due to heating of the construction materials. Cylindrical pans sprayed with water on the underside attracted the highest number of adults especially at high temperatures. Greenhouse tests showed that the inverted cylindrical pan design has potential as an attract-and-kill device for olive fruit fly control. PMID:25368094

Effects of kaolin particle films on the life span of an orb-weaver spider.

PubMed

Benhadi-Marín, Jacinto; Pereira, José Alberto; Santos, Sónia A P

2016-02-01

Araniella cucurbitina (Araneae: Araneidae) is a widespread orb-weaver spider commonly found in agroecosystems. Mineral particle films such as kaolin, due to their protective or anti-feeding action, can represent an alternative to pesticides, especially in organic farming systems, but little is known about its effects on A. cucurbitina. Therefore, we tested the effect of kaolin sprays on the life span of A. cucurbitina under laboratory conditions. Four treatments were tested encompassing different exposure routes. Thus, kaolin sprays were applied on (i) the surface, (ii) the prey (fly), (iii) the spider and (iv) both spider & prey. A control group was tested with water in each treatment. Results showed that sprays of kaolin significantly affected the survival of A. curcubitina when applications were done on the surface and on both spider & prey registering a reduction of 48% and 56%, respectively. Spiders in control obtained higher probability of reaching alive at the end of the assay than those treated with kaolin. Differences observed can be explained by the feeding behavior of the species and may depend on the consumption of the web by the spider and the ratio spider/fly for body size. Copyright © 2015 Elsevier Ltd. All rights reserved.

Chlorfenapyr (A Pyrrole Insecticide) Applied Alone or as a Mixture with Alpha-Cypermethrin for Indoor Residual Spraying against Pyrethroid Resistant Anopheles gambiae sl: An Experimental Hut Study in Cove, Benin

PubMed Central

Ngufor, Corine; Critchley, Jessica; Fagbohoun, Josias; N’Guessan, Raphael; Todjinou, Damien; Rowland, Mark

2016-01-01

Background Indoor spraying of walls and ceilings with residual insecticide remains a primary method of malaria control. Insecticide resistance in malaria vectors is a growing problem. Novel insecticides for indoor residual spraying (IRS) which can improve the control of pyrethroid resistant malaria vectors are urgently needed. Insecticide mixtures have the potential to improve efficacy or even to manage resistance in some situations but this possibility remains underexplored experimentally. Chlorfenapyr is a novel pyrrole insecticide which has shown potential to improve the control of mosquitoes which are resistant to current WHO-approved insecticides. Method The efficacy of IRS with chlorfenapyr applied alone or as a mixture with alpha-cypermeththrin (a pyrethroid) was evaluated in experimental huts in Cove, Southern Benin against wild free flying pyrethroid resistant Anopheles gambiae sl. Comparison was made with IRS with alpha-cypermethrin alone. Fortnightly 30-minute in situ cone bioassays were performed to assess the residual efficacy of the insecticides on the treated hut walls. Results Survival rates of wild An gambiae from the Cove hut site in WHO resistance bioassays performed during the trial were >90% with permethrin and deltamethrin treated papers. Mortality of free-flying mosquitoes entering the experimental huts was 4% in the control hut. Mortality with alpha-cypermethrin IRS did not differ from the control (5%, P>0.656). The highest mortality was achieved with chlorfenapyr alone (63%). The alpha-cypermethrin + chlorfenapyr mixture killed fewer mosquitoes than chlorfenapyr alone (43% vs. 63%, P<0.001). While the cone bioassays showed a more rapid decline in residual mortality with chlorfenapyr IRS to <30% after only 2 weeks, fortnightly mortality rates of wild free-flying An gambiae entering the chlorfenapyr IRS huts were consistently high (50–70%) and prolonged, lasting over 4 months. Conclusion IRS with chlorfenapyr shows potential to significantly improve the control of malaria transmission in pyrethroid resistant areas compared to pyrethroid IRS or the mixture. Thirty minute in situ cone bioassays are not predictive of the performance of chlorfenapyr IRS under field conditions. PMID:27588945

Bait spray for control of European cherry fruit fly: an appraisal based on semi-field and field studies.

PubMed

Böckmann, Elias; Köppler, Kirsten; Hummel, Edmund; Vogt, Heidrun

2014-03-01

The European cherry fruit fly, Rhagoletis cerasi, is the major insect pest of sweet and tart cherries. Its management is becoming increasingly difficult in many countries as formerly effective but broad-spectrum insecticides are removed from the market. With the objective of identifying suitable and environmentally safe alternatives, we investigated bait sprays containing two families of plant-derived insecticides: azadirachtins (NeemAzal-T(®) and NeemAzal-T/S(®) ) and pyrethrins (Spruzit Neu(®) ). In 12 semi-field trials conducted within cages, weekly applications of 0.0001 or 0.0005% neem in a bait formulation effectively reduced fruit infestation. However, addition of 0.000125-0.001% pyrethrins did not improve the efficacy of the neem formulations, and when used alone pyrethrins were less effective than neem alone. Two years of field trials were also conducted within orchards wherein an insecticidal barrier of treated trees excluded immigration of fertile R. cerasi from elsewhere. In blocks treated with 0.0005% neem in a bait formulation, we observed 94% (2011) or 86% (2012) reduction of fruit infestation over control blocks. Bait sprays containing neem are a promising alternative for the management of R. cerasi, especially where the risk of immigration of fertilized females is low, as in isolated orchards or as part of area-wide treatments. © 2013 Society of Chemical Industry.

Active dispersal of Triatoma infestans and other triatomines in the Argentinean arid Chaco before and after vector control interventions.

PubMed

Abrahan, Luciana; Gorla, David; Catalá, Silvia

2016-06-01

Peridomestic structures are considered the main sites where Triatoma infestans (Hemiptera: Reduviidae) remain and disperse, representing the first risk factor for intradomestic invasion, even after vector control activities. This study analyzed T. infestans dispersal during vector control interventions in six rural houses of the arid Chaco (La Rioja, Argentina). Flying and walking dispersers were captured during five months of two consecutive warm seasons after insecticide spraying of intra- and peridomiciles. These data were compared with previous published data in the same scenario but without insecticide spraying in peridomiciles. Recorded climatic conditions were favorable for active dispersion during the study. Total number of T. infestans dispersers moving among domestic habitats decreased after insecticide spraying. Sylvatic triatomines T. guasayana, T. eratyrusiformis, T. garciabesi, and T. platensis, not targeted by insecticide spraying, were captured simultaneously within peridomestic areas and showed higher invasion pressure than T. infestans. Adult T. infestans peridomestic populations showed high nutritional status, indicating low dispersion probability. Some peridomiciles remained infested at the end of the study. However, no intradomiciles were recolonized. These results suggest that there is a low probability of intradomestic recolonization by active dispersion from peridomiciles during 15 months post-spraying. © 2016 The Society for Vector Ecology.

Long-lasting control of Anopheles arabiensis by a single spray application of micro-encapsulated pirimiphos-methyl (Actellic® 300 CS)

PubMed Central

2014-01-01

Background Pyrethroid-resistant mosquitoes are an increasing threat to malaria vector control. The Global Plan for Insecticide Resistance Management (GPIRM) recommends rotation of non-pyrethroid insecticides for indoor residual spraying (IRS). The options from other classes are limited. The carbamate bendiocarb and the organophosphate pirimiphos-methyl (p-methyl) emulsifiable concentrate (EC) have a short residual duration of action, resulting in increased costs due to multiple spray cycles, and user fatigue. Encapsulation (CS) technology was used to extend the residual performance of p-methyl. Methods Two novel p-methyl CS formulations were evaluated alongside the existing EC in laboratory bioassays and experimental hut trials in Tanzania between 2008-2010. Bioassays were carried out monthly on sprayed substrates of mud, concrete, plywood, and palm thatch to assess residual activity. Experimental huts were used to assess efficacy against wild free-flying Anopheles arabiensis, in terms of insecticide-induced mortality and blood-feeding inhibition. Results In laboratory bioassays of An. arabiensis and Culex quinquefasciatus both CS formulations produced high rates of mortality for significantly longer than the EC formulation on all substrates. On mud, the best performing CS killed >80% of An. arabiensis for five months and >50% for eight months, compared with one and two months, respectively, for the EC. In monthly bioassays of experimental hut walls the EC was ineffective shortly after spraying, while the best CS formulation killed more than 80% of An. arabiensis for five months on mud, and seven months on concrete. In experimental huts both CS and EC formulations killed high proportions of free-flying wild An. arabiensis for up to 12 months after spraying. There was no significant difference between treatments. All treatments provided considerable personal protection, with blood-feeding inhibition ranging from 9-49% over time. Conclusions The long residual performance of p-methyl CS was consistent in bioassays and experimental huts. The CS outperformed the EC in laboratory and hut bioassays but the EC longevity in huts was unexpected. Long-lasting p-methyl CS formulations should be more effective than both p-methyl EC and bendiocarb considering a single spray could be sufficient for annual malaria control. IRS with p-methyl 300 CS is a timely addition to the limited portfolio of long-lasting residual insecticides. PMID:24476070

Effect of knowledge and economic status on sandfly control activities by householders at risk of cutaneous leishmaniasis in the subandean region of Huila department, Colombia.

PubMed

Pardo, Raúl H; Carvajal, Alexander; Ferro, Cristina; Davies, Clive R

2006-10-01

Householder vector control measures can be encouraged by health promotion campaigns which take into account peoples' attitudes and focus on key gaps in knowledge. To describe household sandfly control practices in an endemic area of cutaneous leishmaniasis in the department of Huila, Colombia, and determine how these are influenced by attitudes, knowledge and socioeconomic status. A household questionnaire was applied to collect information on: demography, socioeconomic status, knowledge of cutaneous leishmaniasis and of sandflies and their role in transmission, and the control activities practiced. Indoor sandfly abundance was estimated by light trap collections. Amongst 249 interviewees, 86% knew about cutaneous leishmaniasis and 98% sand flies. 35% of interviewees who knew about cutaneous leishmaniasis practiced measures with the purpose of its control. This practice was higher amongst the 32% who knew that sand flies transmit cutaneous leishmaniasis. However, 82% of interviewees practiced sand fly control measures, and these were significantly associated with high sand fly abundance. Measures included smoke, bednets, and house spraying with insecticide or non-insecticidal substances. Householders using the high cost measures (bednets and insecticide) had the highest economic status. Health education programmes should note that sand fly nuisance can initiate control measures, but that knowledge of the role of sand flies in transmission could enhance activities. The socioeconomic findings indicate that targeted bednet subsidies could reduce inequities in health status amongst cutaneous leishmaniasis endemic communities.

Combining epidemiology with basic biology of sand flies, parasites, and hosts to inform leishmaniasis transmission dynamics and control.

PubMed

Courtenay, Orin; Peters, Nathan C; Rogers, Matthew E; Bern, Caryn

2017-10-01

Quantitation of the nonlinear heterogeneities in Leishmania parasites, sand fly vectors, and mammalian host relationships provides insights to better understand leishmanial transmission epidemiology towards improving its control. The parasite manipulates the sand fly via production of promastigote secretory gel (PSG), leading to the "blocked sand fly" phenotype, persistent feeding attempts, and feeding on multiple hosts. PSG is injected into the mammalian host with the parasite and promotes the establishment of infection. Animal models demonstrate that sand flies with the highest parasite loads and percent metacyclic promastigotes transmit more parasites with greater frequency, resulting in higher load infections that are more likely to be both symptomatic and efficient reservoirs. The existence of mammalian and sand fly "super-spreaders" provides a biological basis for the spatial and temporal clustering of clinical leishmanial disease. Sand fly blood-feeding behavior will determine the efficacies of indoor residual spraying, topical insecticides, and bed nets. Interventions need to have sufficient coverage to include transmission hot spots, especially in the absence of field tools to assess infectiousness. Interventions that reduce sand fly densities in the absence of elimination could have negative consequences, for example, by interfering with partial immunity conferred by exposure to sand fly saliva. A deeper understanding of both sand fly and host biology and behavior is essential to ensuring effectiveness of vector interventions.

Environmental sanitary interventions for preventing active trachoma.

PubMed

Rabiu, M; Alhassan, M; Ejere, H

2005-04-18

Trachoma is the second or third major cause of blindness. It is responsible for about six million blind people worldwide, mostly in the poor communities of developing countries. One of the major strategies advocated for the control of the disease is the application of various environmental sanitary measures to such communities. To assess the evidence for the effectiveness of environmental sanitary measures on the prevalence of active trachoma in endemic areas. We searched the Cochrane Central Register of Controlled Trials - CENTRAL (which contains the Cochrane Eyes and Vision Group Trials Register) on The Cochrane Library (Issue 4, 2004), MEDLINE (1966 to January 2005), EMBASE (1980 to January 2005), LILACS (April 2004), the reference list of trials and the Science Citation Index. We also contacted agencies, experts and researchers in trachoma control. This review included randomised and quasi-randomised controlled trials comparing any form of environmental hygiene measures with no measure. These hygienic measures included fly control, provision of water and health education. Participants in the trials were people normally resident in the trachoma endemic areas. Two authors independently extracted data and assessed the quality of trials. Study authors were contacted for additional information. Three trials met the inclusion criteria but meta-analysis was not conducted due to heterogeneity of the studies. Two studies that assessed insecticide spray as a fly control measure found that trachoma is reduced by at least 55% to 61% with this measure compared to no intervention. One study found that another fly control measure, latrine provision, reduced trachoma by 29.5% compared to no intervention; this was, however, not statistically significantly different. Another study revealed that health education on personal and household hygiene reduced the incidence of trachoma such that the odds of reducing trachoma in the health education village was about twice that of the no intervention village. However, all the studies have some methodological concerns relating to concealment of allocation and non-consideration of clustering effect in data analysis. There is evidence that insecticide spray as a fly control measure reduces trachoma significantly. Latrine provision as a fly control measure has not demonstrated significant trachoma reduction. Health education may be effective in reducing trachoma. There is a dearth of data to determine the effectiveness of all aspects of environmental sanitation in the control of trachoma.

Behavioral responses of two dengue virus vectors, Aedes aegypti and Aedes albopictus (Diptera: Culicidae), to DUET and its components.

PubMed

Clark, Gary G; Golden, Frances V; Allan, Sandra A; Cooperband, Miriam F; McNelly, James R

2013-09-01

Ultralow volume droplets of DUET, prallethrin, and sumithrin at a sublethal dose were applied to unfed (nonbloodfed) and bloodfed female Aedes aegypti L. and Aedes albopictus (Skuse) in a wind tunnel. Control spray droplets only contained inert ingredients. Individual mosquitoes were videotaped before, during, and after spraying and various behaviors analyzed. During the spray periods of all three pesticide treatments, mosquitoes spent a greater percentage of time moving, and the distance moved was greater than for mosquitoes in the control treatments. In the postspray period, the percent of time moving increased for mosquitoes exposed to all pesticide treatments compared with the controls. After treatment, all females spent more time walking compared with controls, with unfed Ae. aegypti females walking more after exposure to DUET and sumithrin than after exposure to prallethrin and the control. Pesticide exposure increased flying in both species. Sumithrin exposure increased activity and velocity of unfed mosquitoes more than bloodfed mosquitoes. DUET and sumithrin treatments enhanced activity of Ae. aegypti females more than Ae. albopictus females.

Temperature-Mediated Kill and Oviposition of Western Cherry Fruit Fly (Diptera: Tephritidae) in the Presence of Spinosad.

PubMed

Yee, Wee L

2016-02-01

Western cherry fruit fly, Rhagoletis indifferens Curran (Diptera: Tephritidae), is a quarantine pest of sweet cherry (Prunus avium (L.) L.) that is managed using insecticides, including spinosad, an organic compound that can be applied in low spray volumes. Identifying factors that can increase the efficacy of spinosad can be useful for improving fly control. Here, the major objective was to determine if temperature mediates kill and oviposition of R. indifferens in the presence of low spinosad coverage in the laboratory. Experiments were conducted by placing flies in cages with cherries and with a Petri dish containing 3-12 small spots of dry spinosad at 18.3, 23.9, and 29.4°C. Effects of spinosad rates were also determined. More flies were killed at 23.9 and 29.4°C than at 18.3°C by 1-7 d post exposure. More flies were killed at 29.4 than 23.9°C by 1 d post exposure. However, flies laid more eggs at these temperatures than at 18.3°C. Higher spinosad rates increased kill and decreased oviposition, but even within the highest rate, oviposition was greater at 29.4 than 18.3°C. More flies walked over 5-min observation periods at 29.4 and 23.9°C than 18.3°C, suggesting higher temperatures up to 29.4°C increase kill by increasing fly contact with spinosad as well as increase oviposition rate. Results suggest that spinosad rates in sprays used against R. indifferens should be greater at higher than lower ambient temperatures. Published by Oxford University Press on behalf of Entomological Society of America 2015. This work is written by a US Government employee and is in the public domain in the US.

Contingency Pest Management Guide. 2010 Edition

DTIC Science & Technology

2010-08-01

indoors as a residual spray to walls, ceilings, window screens and other fly resting areas. Apply outside as a residual ...applications. Cypermethrin (Demon WP) 35.6% 6840-01-390-4822 LB 1 lb jar 1 packet/gal 0.1% Apply indoors as a residual spray to walls, ceilings... indoors as a coarse, low-pressure spray where pests are found. Apply outdoors as a residual spray to lawns, porches and similar areas. May not

Worker exposure and a risk assessment of malathion and fenthion used in the control of Mediterranean fruit fly in South Australia.

PubMed

Edwards, John W; Lee, Su-Gil; Heath, Linda M; Pisaniello, Dino L

2007-01-01

In 2001, an outbreak of Mediterranean fruit fly in Adelaide was controlled by South Australian Government workers applying organophosphorus insecticides (OPs) to domestic gardens. Residents made claims of adverse effects associated with allegations that worker application practices were poor and led to contamination of homes, residents and pets. The concerns led to a Parliamentary enquiry, the suspension of OP applications for fruit fly control, and the investigation of alternative methods of combating fruit fly in metropolitan Adelaide. The extent of exposure of workers and residents was not estimated. This paper describes a simulated application of the OPs concerned (fenthion and malathion) with measurements of potential exposure through inhalation, dermal contact and deposition of pesticides on surfaces. The data were used as part of a toxicological risk assessment to determine the likely impact of the use of these insecticides. Malathion, used as a 1% suspension in a protein bait mixture, was found to have little potential for airborne exposure, although some workers were found to have up to 0.315 microg/cm(2) malathion deposited on overalls (principally on forearms) and over 500 microg deposited on liner gloves and hats, respectively. Risks to workers and residents were low, with exposures likely to be a small fraction of the acceptable daily intake. Fenthion, used as a 0.05% foliar cover spray, was found between 0.02 and 0.23 mg/m(3) in air 10 m downwind from spray activity and was unlikely to pose a significant risk to residents, since exposures were of short durations of up to 20 min. Personal air samples of spray workers averaged 0.55 mg/m(3) (Workplace Exposure Standard 0.20mg/m(3)). Since workers were usually engaged in spraying for a large proportion of the day, this demonstrates the need for respiratory protective equipment. Maximum deposition of fenthion on workers overalls ranged from 0.06 to over 0.20 microg/cm(2), although little was found on gloves and hats, suggesting workers were skilled in avoiding the plume of overspray. Dialkyl phosphates (metabolites of OP insecticides) were not detected in urine of workers, and there were no changes observed in serum cholinesterase (SChE) enzyme activities 24h following the simulation. These data suggest absorption of OP insecticides by workers was negligible. Deposition on surfaces 5 and 10 m downwind ranged from none detected to 145 microg/cm(2), suggesting that exposure of residents and children in contact with contaminated surfaces (such as garden furniture or play equipment) is possible. Estimates of the potential dermal intake of fenthion by children from contaminated surfaces suggested that risks of acute and chronic effects are slight, since exposures may occur for short periods at intervals of approximately 10 days during fruit fly outbreaks.

The paratransgenic sand fly: a platform for control of Leishmania transmission.

PubMed

Hurwitz, Ivy; Hillesland, Heidi; Fieck, Annabeth; Das, Pradeep; Durvasula, Ravi

2011-05-19

Leishmania donovani is transmitted by the bite of the sand fly, Phlebotomus argentipes. This parasite is the agent of visceral leishmaniasis (VL), an endemic disease in Bihar, India, where prevention has relied mainly on DDT spraying. Pesticide resistance in sand fly populations, environmental toxicity, and limited resources confound this approach. A novel paratransgenic strategy aimed at control of vectorial transmission of L. donovani is presented using Bacillus subtilis, a commensal bacterium isolated from the sand fly gut. In this work, B. subtilis expressing Green Fluorescent Protein (GFP) was added to sterilized larval chow. Control pots contained larval chow spiked either with untransformed B. subtilis or phosphate-buffered saline. Fourth-instar P. argentipes larvae were transferred into the media and allowed to mature. The number of bacterial colony forming units, relative abundance and the mean microbial load were determined per developmental stage. Addition of B. subtilis to larval chow did not affect sand fly emergence rates. B. cereus and Lys fusiformis were identified at each developmental stage, revealing transstadial passage of endogenous microbes. Larvae exposed to an exogenous bolus of B. subtilis harbored significantly larger numbers of bacteria. Bacterial load decreased to a range comparable to sand flies from control pots, suggesting an upper limit to the number of bacteria harbored. Emerging flies reared in larval chow containing transformed B. subtilis carried large numbers of these bacteria in their gut lumens. Strong GFP expression was detected in these paratransgenic flies with no spread of transformed bacteria to other compartments of the insects. This is the first demonstration of paratransgenic manipulation of P. argentipes. Paratransgenic manipulation of P. argentipes appears feasible. Expression of leishmanicidal molecules via commensal bacteria commonly found at breeding sites of P. argentipes could render adult sand flies refractory to L. donovani infection.

Working Group on Ice Forces (4th) State-of-the-Art Report Held in Iowa City, Iowa in 1986.

DTIC Science & Technology

1989-02-01

INTRODUCTION When droplets generated from sea water fly in cold air, cool and hit an object, spray ice will form. Spray ice causes hazards and...or spray generated by waves hitting the structure. Wind-generated spray forms as a result of direct whipping of wave crests by the wind and of bursting...Spray generated by waves hitting a structure, on the other hand, can result in very high liquid water contents. Values of up to 5 kgm -3 have been

Wind tunnel studies on spray deposition on leaves of tree species used for windbreaks and exposure of honey bees.

PubMed

Ucar, Tamer; Hall, Franklin R; Tew, James E; Hacker, James K

2003-03-01

A wind tunnel study was conducted to determine pesticide deposition on commonly used windbreak tree species used as spray drift barriers and associated exposure of honey bees. Although it has been known that windbreaks are effective in reducing chemical drift from agricultural applications, there is still an enormous information and data gap on details of the dependence of the mechanism on the biological materials of the barriers and on standardization of relevant assessment methods. Beneficial arthropods like honey bees are adversely affected by airborne drift of pesticides. A study was initiated by first establishing a wind tunnel to create a controlled environment for capture efficiency work. Suitable spray parameters were determined after a preliminary study to construct and develop a wind tunnel protocol. A tracer dye solution was sprayed onto the windbreak samples and honey bees located in the wind tunnel at various simulated wind speeds. Analysis of data from this work has shown that needle-like foliage of windbreak trees captures two to four times more spray than broad-leaves. In addition, it was determined that, at lower wind speeds, flying bees tend to capture slightly more spray than bees at rest.

Distribution of arsenic and mercury in lime spray dryer ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Panuwat Taerakul; Ping Sun; Danold W. Golightly

The partitioning of As and Hg in various components of lime spray dryer (LSD) ash samples from a coal-fired boiler was characterized to better understand the form and fate of these elements in flue gas desulfurization byproducts. LSD ash samples, collected from the McCracken Power Plant on the Ohio State University campus, were separated by a 140-mesh (106 {mu}m) sieve into two fractions: a fly-ash-/unburned-carbon-enriched fraction (> 106 {mu}m) and a calcium-enriched fraction (< 106 {mu}m). Unburned carbon and fly ash in the material > 106 {mu}m were subsequently separated by density using a lithium heteropolytungstate solution. The concentrations ofmore » As and Hg were significant in all fractions. The level of As was consistently greater in the calcium-enriched fraction, while Hg was evenly distributed in all components of LSD ash. Specific surface area was an important factor controlling the distribution of Hg in the different components of LSD ash, but not for As. Comparing the LSD ash data to samples collected from the economizer suggests that As was effectively captured by fly ash at 600{sup o}C, while Hg was not. Leaching tests demonstrated that As and Hg were more stable in the calcium-enriched fraction than in the fly-ash- or carbon-enriched fractions, potentially because of the greater pH of the leachate and subsequently greater stability of small amounts of calcium solids containing trace elements in these fractions. 37 refs., 8 figs., 2 tabs.« less

Response of female Ceratitis capitata (Diptera: Tephritidae) to a spinosad bait and polymer matrix mixture with extended residual effect in Hawaii.

PubMed

Piñero, Jaime C; Souder, Steven K; Gomez, Luis E; Mau, Ronald F L; Vargas, Roger I

2011-12-01

The effectiveness of foliar applications of protein baits against pestiferous fruit flies (Tephritidae) can be adversely affected by a rapid loss of attractive volatile compounds and by rainfall due to the high water solubility of the baits. In a large coffee, Coffea arabica L., plantation in Hawaii with high and low populations of Mediterranean fruit fly, Ceratitis capitata (Wiedemann) (Diptera: Tephritidae), the relative attractiveness of GF-120 NF Naturalyte Fruit Fly Bait as either a 40% (vol:vol) spray solution (= GF-120 NF) or as a formulated proprietary amorphous polymer matrix (= GF-120 APM) was compared. The GF-120 APM formulations contained either, 25, 50, or 75% of GF-120 NF (wt:wt). All baits were tested in association with visually attractive yellow bait stations as a way of standardizing the evaluations. With both high and low C. capitata populations, significantly more females were attracted to the fresh sprayed GF-120 NF than to any of the three fresh GF-120 APM formulations. The attractiveness of GF-120 sprayed decreased significantly after 1 wk, whereas 1-wk-old GF-120 APM formulations were as attractive as similar fresh formulations. GF-120 APM 75% aged for 3 wk outperformed similarly-aged sprayed GF-120 NF with comparatively high C. capitata populations. With low populations, both GF-120 APM 75% and GF-120 APM 50% aged for 2 wk outperformed the similarly aged sprayed GF-120 NF. Combined findings indicate that APM mixed with either 50 or 75% GF-120 applied to bait stations can be attractive to female C. capitata for up to 3 wk longer than the standard sprayed GF-120 NF.

Comparison of cauliflower-insect-fungus interactions and pesticides for cabbage root fly control.

PubMed

Razinger, Jaka; Žerjav, Metka; Zemljič-Urbančič, Meta; Modic, Špela; Lutz, Matthias; Schroers, Hans-Josef; Grunder, Jürg; Fellous, Simon; Urek, Gregor

2017-12-01

Cabbage root fly (Delia radicum L.) control represents a major challenge in brassica production, therefore different management strategies for its control were tested in conventionally managed open field cauliflower production. Strategies included treatments with low-risk methods such as nitrogen lime, the insecticide spinosad and the Beauveria bassiana ATCC 74040-based biopesticide Naturalis. Their effects were compared with treatments based on nonformulated fungal species Metarhizium brunneum, B. bassiana, Clonostachys solani, Trichoderma atroviride, T. koningiopsis, and T. gamsii and commercial insecticides λ-cyhalothrin and thiamethoxam. Spinosad and thiamethoxam were pipetted to individual plants before transplanting; λ-cyhalothrin was sprayed after transplanting; nitrogen lime was applied at first hoeing. Nonformulated fungi were delivered onto cauliflower plantlets' roots as a single pretransplantation inoculation. The cabbage root fly population dynamics exhibited a strong spatiotemporal variation. The lowest number of cabbage root fly pupae recovered from cauliflower roots in the field experiments was recorded in plants treated with spinosad (significant reduction), followed by Naturalis and one of the tested M. brunneum strains (nonsignificant reduction). Significantly more pupae were counted in the nitrogen lime treatment. The field experiments showed that a single drench of cauliflower plantlets with spinosad offered consistent and enduring cabbage root fly control. Naturalis and nonformulated fungal isolates did not decrease cabbage root fly pressure significantly, apparently due to lack of statistical power. The implications of the substantial intra- and inter-annual pest pressure variation and the benefits of using single plant treatments are discussed, and recommendations for improvement of rhizosphere-competence utilizing biological control strategies provided. © 2017 Institute of Zoology, Chinese Academy of Sciences.

Visceral Leishmaniasis on the Indian Subcontinent: Modelling the Dynamic Relationship between Vector Control Schemes and Vector Life Cycles.

PubMed

Poché, David M; Grant, William E; Wang, Hsiao-Hsuan

2016-08-01

Visceral leishmaniasis (VL) is a disease caused by two known vector-borne parasite species (Leishmania donovani, L. infantum), transmitted to man by phlebotomine sand flies (species: Phlebotomus and Lutzomyia), resulting in ≈50,000 human fatalities annually, ≈67% occurring on the Indian subcontinent. Indoor residual spraying is the current method of sand fly control in India, but alternative means of vector control, such as the treatment of livestock with systemic insecticide-based drugs, are being evaluated. We describe an individual-based, stochastic, life-stage-structured model that represents a sand fly vector population within a village in India and simulates the effects of vector control via fipronil-based drugs orally administered to cattle, which target both blood-feeding adults and larvae that feed on host feces. Simulation results indicated efficacy of fipronil-based control schemes in reducing sand fly abundance depended on timing of drug applications relative to seasonality of the sand fly life cycle. Taking into account cost-effectiveness and logistical feasibility, two of the most efficacious treatment schemes reduced population peaks occurring from April through August by ≈90% (applications 3 times per year at 2-month intervals initiated in March) and >95% (applications 6 times per year at 2-month intervals initiated in January) relative to no control, with the cumulative number of sand fly days occurring April-August reduced by ≈83% and ≈97%, respectively, and more specifically during the summer months of peak human exposure (June-August) by ≈85% and ≈97%, respectively. Our model should prove useful in a priori evaluation of the efficacy of fipronil-based drugs in controlling leishmaniasis on the Indian subcontinent and beyond.

Effect of Bauxite addition on Adhesion Strength and Surface Roughness of Fly ash based Plasma Sprayed Coatings

NASA Astrophysics Data System (ADS)

Bhuyan, S. K.; Samal, S.; Pattnaik, D.; Sahu, A.; Swain, B.; Thiyagarajan, T. K.; Mishra, S. C.

2018-03-01

The environment is being contaminated with advancement of new technology, day by day. One of the primary sources for this contamination is the industrial waste. Industrialization is the prime reason behind the prosperity of any country to meet the materialistic demand. To run the industries, a huge amount of (electric) power is needed and hence need for thermal power plants to serve the purpose. In present scenario, coal fired thermal power plants are set up which generates a huge quantity of Fly ash. Consumption of industrial waste (Fly ash), continually a major concern for human race. In recent years, fly ash is being utilized for various purposes i.e. making bricks, mine reclamation, production of cements etc. The presence of Silica and Alumina in fly ash makes it useful for thermal barrier applications also. The plasma spray technology has the advantage of being able to process any types of metal/ceramic mineral, low-grade-ore minerals etc. to make value-added products and also to deposit ceramics, metals and a combination of these to deposit composite coatings with desired microstructure and required properties on a range of substrate materials. The present work focuses on utilization of fly ash mixing with bauxite (ore mineral) for a high valued application. Fly ash with 10 and 20% bauxite addition is used to deposit plasma spray overlay coatings at different power levels (10-20kW) on aluminum and mild steel substrates. Adhesion strength and surface roughness of the coatings are evaluated. Phase composition analysis of the coatings were done using X-ray diffraction analysis. Surface morphology of the coatings was studied using a scanning electron microscope (SEM). Maximum adhesion strength of 4.924 MPa is obtained for the composition fly ash and bauxite (10%), coated on mild steel at 16kW torch power level. The surface roughness (Ra) of the coatings is found to vary between 10.0102 to 17.2341 micron.

Evaluation of chemical spraying and environmental management efficacy in areas with minor previous application of integrated control actions for visceral leishmaniasis in Brazil.

PubMed

Lara-Silva, Fabiana de Oliveira; Michalsky, Érika Monteiro; Fortes-Dias, Consuelo Latorre; Fiuza, Vanessa de Oliveira Pires; Dias, Edelberto Santos

2017-12-01

Leishmaniases are vector-borne diseases that are transmitted to humans through the bite of Leishmania-infected phlebotomine sand flies (Diptera:Psychodidae). The main proved vector of visceral leishmaniais (VL) in the New World - Lutzomyia longipalpis - is well-adapted to urban areas and has extensive distribution within the five geographical regions of Brazil. Integrated public health actions directed for the vector, domestic reservoir and humans for the control of VL are preferentially applied in municipalities with higher epidemiological risk of transmission. In this study, we evaluated the individual impact of two main vector control actions - chemical spraying and environmental management - in two districts with no reported cases of human VL. Although belonging to an endemic municipality for VL in Brazil, the integrated control actions have not been applied in these districts due to the absence of human cases. The number of L. longipalpis captured in a two-year period was used as indicator of the population density of the vector. After chemical spraying a tendency of reduction in L. longipalpis was observed but with no statistical significance compared to the control. Environmental management was effective in that reduction and it may help in the control of VL by reducing the population density of the vector in a preventive and more permanent action, perhaps associated with chemical spraying. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluation of Insecticides, Clothing Repellents, and Other Approaches to the Control of Coastal Sand Flies, Culicoides spp.

DTIC Science & Technology

1981-11-01

Meteorlogical data during the insecticide applica- tions were collected by a weather team from the Marine Corp. Air Station, Beufort, South Carolina...u ~ - 0 ’ >4 z 00 0~~1 Cc140 ) ( 4 u 1 -*l,(i AM𔃺 Table 7.-- Meteorlogical Data for Spray Operations Over Parris Island, South Carolina, April 7

Field trials of fatty acids and geraniol applied to cattle for suppression of horn flies, Haematobia irritans (Diptera: Muscidae), with observations on fly defensive behaviors.

PubMed

Mullens, Bradley A; Watson, D Wes; Gerry, Alec C; Sandelin, Broc A; Soto, Diane; Rawls, Diana; Denning, Steve; Guisewite, Lena; Cammack, Jonathan

2017-10-15

Adult horn fly populations were tracked on cattle for 2-week periods before, during and after multiple treatments (every 3-4days) with two repellents in a mineral oil carrier. Cattle were sprayed four times in a two-week period either with 2% geraniol (125ml/cow) or a 15% mixture of short chain fatty acids (C8-C9-C10)(250ml/cow), and there were untreated control cattle. Trials were conducted in California and North Carolina for 3 summers. Short-term fly counts (same day) on treated cattle were reduced by 61-99%, depending on material and trial, and the fatty acid mixture provided better control than geraniol. Horn fly counts were suppressed for 1-3 d and rebounded somewhat after both treatments. Consecutive treatments showed evidence of persistent impact in California where herds were more isolated. Rebounds to pre-treatment levels 3-4 d after treatment occurred more often in North Carolina, where other infested cattle were closer to treated herds. By 3-4 d post-treatment, horn flies were reduced by 29-61% in California and 0-83% in North Carolina, relative to pre-treatment. Background behavior frequencies were assessed from hundreds of counts on untreated, infested California cattle, where horn flies were the only abundant biting fly. Behavior averages were 16.5 tail flicks, 7.6 skin twitches, 1.2 head throws, or 0.2 leg stamps per 2min observation period. At horn fly densities from about 200 to more than 1000 flies per animal (moderate to high numbers), fly defensive behaviors on control cattle were poorly related (or unrelated) to fly numbers. Immediately after repellent application, however, flies were almost absent and behavior frequencies dropped distinctly. Cattle fly defensive behaviors therefore seem to be quite sensitive to low (less than 100 flies/animal) horn fly densities, and behaviors would be a poor quantitative tool to track fly stress at moderate densities and above. Both geraniol and the fatty acids show promise for horn fly control, especially in organic agriculture. Treatments at 1-2 d intervals probably would keep infestations below the economic threshold (200 flies/cow). Copyright © 2017 Elsevier B.V. All rights reserved.

FLY ASH RECYCLE IN DRY SCRUBBING

EPA Science Inventory

The paper describes the effects of fly ash recycle in dry scrubbing. (Previous workers have shown that the recycle of product solids improves the utilization of slaked lime--Ca(OH)2--for sulfur dioxide (SO2) removal by spray dryers with bag filters.) In laboratory-scale experimen...

Spray scrubbing of particulate-laden SO(2) using a critical flow atomizer.

PubMed

Bandyopadhyay, Amitava; Biswas, Manindra Nath

2008-08-01

The performance of a spray tower using an energy efficient two-phase critical flow atomizer on the scrubbing of particulate-laden SO(2) using water and dilute NaOH is reported in this article. Experimentation revealed that SO(2) removal was enhanced due to presence of particles (fly-ash) and almost 100% removal efficiency was achieved in water scrubbing. The removal efficiency is elucidated in reference to atomizing air pressure, droplet diameter and droplet velocity besides other pertinent variables of the system studied. The presence of fly-ash particles improved the removal efficiency to about 20% within the range of variables studied. Empirical and semi-empirical correlations were developed for predicting the removal efficiency in water and dilute NaOH respectively. Predicted data fitted excellently well with experimental values. The performance of the spray tower is compared with the performances of existing systems and very encouraging results are obtained.

Investigations with misting systems, barrier treatments, and space sprays operationalized with a mobile pesticide app

USDA-ARS?s Scientific Manuscript database

US military operations in field conditions face significant negative impacts on mission readiness from disease-vector and nuisance populations of filth flies, mosquitoes, and sand flies. Although measures are in place to protect personnel in the field from these insect threats, experiences from rece...

Use of Trichoderma fungi in spray solutions to reduce Moniliophthora roreri infection of Theobroma cacao fruits in Northeastern Costa Rica.

PubMed

Seng, John; Herrera, Geovanny; Vaughan, Christopher S; McCoy, Michael B

2014-09-01

Cacao (Theobroma cacao) is an important cash crop in tropical climates such as that of Latin America. Over the past several decades, the infection of cultivated cacao by Moniliophthllora roreri, known commonly as "monilia", has significantly hindered cacao production in Latin America. Studies have proposed the use of Trichoderma sp. fungi in biocontrol treatments to prevent and reduce monilia infection, yet tests of Trichoderma-containing spray treatments on cacao agroforests have produced mixed results. Researchers and agricultural workers have suggested that addition of soil, fly ash, or other carbon sources to a Trichoderma spray may improve its efficacy in fighting monilia. To test these suggestions, we designed a series of spray mixtures including Thichoderma cultures, soil, and all necessary controls. We applied the spray mixtures to 80 cacao trees (20 trees for each of four resistant-selected clones to monilia) at the FINMAC organic cacao plantation in Pueblo Nuevo de Guacimo, Limón Province, in northeastern Costa Rica in March-April 2013. Five treatments were applied (control, water, water plus sterilized soil, water plus Trichoderma, and water plus sterilized soil plus Trichoderma). Each treatment was applied to four trees of each clone. We monitored the incidence of monilia infection under each spray treatment over the course of 35d. We found that spraying entire cacao trees two times with a mixture containing Trichoderma and sterilized soil significantly reduced the incidence of monilia infection by 11% (p ≤ 0.05) in only 35d, as compared to the control. This reduction in loss of cacao pods translates into an increase of plantation mean productivity of 1,500 kg dried beans/ha by 198 kg/ha up to 1,698 kg/ha or by a total increase over the whole 110 ha plantation by 21,780 kg. We propose that using such an antifungal spray over the whole course of a crop cycle (120 days) would decrease infection incidence even more. Application of this fungal control measure has the potential of revitalizing the production of cacao in the region.

Implementing a Spinosad-Based Local Bait Station to Control Bactrocera cucurbitae (Diptera: Tephritidae) in High Rainfall Areas of Reunion Island

PubMed Central

Delpoux, Camille; Deguine, Jean-Philippe

2015-01-01

Three species of fruit flies cause serious damage to cucurbit crops on Reunion Island: Bactrocera cucurbitae (Diptera: Tephritidae) (Coquillett 1899), Dacus ciliatus (Loew 1901), and Dacus demmerezi (Bezzi 1917). To control them, a program of agroecological management of cucurbit flies has been implemented based on the application of Synéis-appât, especially spot sprays on corn borders. However, the high rainfall on Reunion Island limits the long-term efficiency of the bait; in addition, this method cannot be used for large chayote trellises, because corn borders cannot be planted around them. The aim of this study was to design a bait station adapted to prevailing conditions on Reunion Island. An ‘umbrella trap’ tested in Taiwan was used as a reference to compare its efficacy with our local bait station. Experiments were conducted in field cages on B. cucurbitae to test different characteristics of bait stations and to construct one using local materials. Results were validated in the field. The attractiveness of the bait station was related mainly to the color of the external surface, yellow being the most attractive color. The efficacy of the bait station with respect to fly mortality was found to be linked to the accessibility of the bait, and direct application of Synéis-appât on the bait station was found to be the most efficient. In the field, B. cucurbitae were more attracted to the local bait station than to the umbrella trap, while the two other fly species displayed equal attraction to both trap types. Our local bait station is a useful alternative to spot sprays of Synéis-appât and is now included in a local pest management program and is well accepted by farmers. PMID:25688089

Implementing a spinosad-based local bait station to control Bactrocera cucurbitae (Diptera: Tephritidae) in high rainfall areas of Reunion Island.

PubMed

Delpoux, Camille; Deguine, Jean-Philippe

2015-01-01

Three species of fruit flies cause serious damage to cucurbit crops on Reunion Island: Bactrocera cucurbitae (Diptera: Tephritidae) (Coquillett 1899), Dacus ciliatus (Loew 1901), and Dacus demmerezi (Bezzi 1917). To control them, a program of agroecological management of cucurbit flies has been implemented based on the application of Synéis-appât, especially spot sprays on corn borders. However, the high rainfall on Reunion Island limits the long-term efficiency of the bait; in addition, this method cannot be used for large chayote trellises, because corn borders cannot be planted around them. The aim of this study was to design a bait station adapted to prevailing conditions on Reunion Island. An 'umbrella trap' tested in Taiwan was used as a reference to compare its efficacy with our local bait station. Experiments were conducted in field cages on B. cucurbitae to test different characteristics of bait stations and to construct one using local materials. Results were validated in the field. The attractiveness of the bait station was related mainly to the color of the external surface, yellow being the most attractive color. The efficacy of the bait station with respect to fly mortality was found to be linked to the accessibility of the bait, and direct application of Synéis-appât on the bait station was found to be the most efficient. In the field, B. cucurbitae were more attracted to the local bait station than to the umbrella trap, while the two other fly species displayed equal attraction to both trap types. Our local bait station is a useful alternative to spot sprays of Synéis-appât and is now included in a local pest management program and is well accepted by farmers. © The Author 2015. Published by Oxford University Press on behalf of the Entomological Society of America.

Temperature-mediated kill and oviposition of Western Cherry Fruit Fly (Diptera: Tephritidae) in the presence of Spinosad

USDA-ARS?s Scientific Manuscript database

Western cherry fruit fly, Rhagoletis indifferens Curran (Diptera: Tephritidae), is a quarantine pest of sweet cherry (Prunus avium (L.) L.) that is managed using insecticides, including spinosad, an organic compound that can be applied in low spray volumes. Identifying factors that can increase the...

Treatment of fly ash for use in concrete

DOEpatents

Boxley, Chett [Park City, UT

2012-05-15

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

CO.sub.2 utilization in electrochemical systems

DOEpatents

Boxley, Chett; Akash, Akash; Zhao, Qiang

2013-01-22

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Urban parasitology: visceral leishmaniasis in Brazil.

PubMed

Harhay, Michael O; Olliaro, Piero L; Costa, Dorcas Lamounier; Costa, Carlos Henrique Nery

2011-09-01

Since the early 1980s, visceral leishmaniasis (VL) which is, in general, a rural zoonotic disease, has spread to the urban centers of the north, and now the south and west of Brazil. The principal drivers differ between cities, though human migration, large urban canid populations (animal reservoir), and a decidedly peripatetic and adaptable sand fly vector are the primary forces. The exact number of urban cases remains unclear as a result of challenges with surveillance. However, the number of urban cases registered continues to increase annually. Most control initiatives (e.g. culling infected dogs and household spraying to kill the sand fly) could be effective, but have proven hard to maintain at large scales due to logistical, financial and other reasons. In this article, the urbanization of VL in Brazil is reviewed, touching on these and other topics related to controlling VL within and outside Brazil. Copyright © 2011 Elsevier Ltd. All rights reserved.

Prallethrin-induced excitation increases contact between sprayed ultra-low-volume droplets and flying mosquitoes (Diptera: Culicidae) in a wind tunnel

USDA-ARS?s Scientific Manuscript database

Mosquitoes are important in the United States due to their roles as pestiferous biters and vectors of diseases such as West Nile Virus and Dengue. Conventional applications of pesticides in spray clouds are often limited by their ability to contact and kill mosquitoes that may be resting or hiding ...

Sucrose Improves Insecticide Activity Against Drosophila suzukii (Diptera: Drosophilidae).

PubMed

Cowles, Richard S; Rodriguez-Saona, Cesar; Holdcraft, Robert; Loeb, Gregory M; Elsensohn, Johanna E; Hesler, Steven P

2015-04-01

The addition of sucrose to insecticides targeting spotted wing drosophila, Drosophila suzukii (Matsumura), enhanced lethality in laboratory, semifield, and field tests. In the laboratory, 0.1% sucrose added to a spray solution enhanced spotted wing drosophila feeding. Flies died 120 min earlier when exposed to spinosad residues at label rates enhanced with sucrose. Added sucrose reduced the LC50 for dried acetamiprid residues from 82 to 41 ppm in the spray solution. Laboratory bioassays of spotted wing drosophila mortality followed exposure to grape and blueberry foliage and/or fruit sprayed and aged in the field. On grape foliage, the addition of 2.4 g/liter of sugar with insecticide sprays resulted in an 11 and 6% increase of spotted wing drosophila mortality at 1 and 2 d exposures to residues, respectively, averaged over seven insecticides with three concentrations. In a separate experiment, spinetoram and cyantraniliprole reduced by 95-100% the larval infestation of blueberries, relative to the untreated control, 7 d after application at labeled rates when applied with 1.2 g/liter sucrose in a spray mixture, irrespective of rainfall; without sucrose infestation was reduced by 46-91%. Adding sugar to the organically acceptable spinosyn, Entrust, reduced larval infestation of strawberries by >50% relative to without sugar for five of the six sample dates during a season-long field trial. In a small-plot field test with blueberries, weekly applications in alternating sprays of sucrose plus reduced-risk insecticides, spinetoram or acetamiprid, reduced larval infestation relative to the untreated control by 76%; alternating bifenthrin and phosmet (without sucrose) reduced infestation by 65%. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Development of Ceramic Coating on Metal Substrate using Industrial Waste and Ore Minerals

NASA Astrophysics Data System (ADS)

Bhuyan, S. K.; Thiyagarajan, T. K.; Mishra, S. C.

2017-02-01

The technological advancement in modern era has a boon for enlightening human life; but also is a bane to produce a huge amount of (industrial) wastes, which is of great concern for utilization and not to create environmental threats viz. polution etc. In the present piece of research work, attempts have been made to utilize fly ash (wastes of thermal power plants) and along with alumina bearing ore i.e. bauxite, for developing plasma spray ceramic coatings on metals. Fly ash and with 10 and 20% bauxite addition is used to deposit plasma spray coatings on a metal substrate. The surface morphology of the coatings deposited at different power levels of plasma spraying investigated through SEM and EDS analysis. The coating thickness is measured. The porosity levels of the coatings are evaluated. The coating hardness isalso measured. This piece of research work will be beneficial for future development and use of industrial waste and ore minerals for high-valued applications.

Tolerance of house fly, Musca domestica L. (Diptera: Muscidae) to dichlorvos (76% EC) an insecticide used for fly control in the tsunami-hit coastal villages of southern India.

PubMed

Srinivasan, R; Jambulingam, P; Gunasekaran, K; Boopathidoss, P S

2008-02-01

The Directorate of Public Health (DPH), Tamil Nadu, in southern India employed spraying of dichlorvos (76% EC) for quick elimination of fly concentrations in the tsunami-hit coastal villages at the concentration of 304g (a.i.)/10,000m(2). However, nuisance of house flies remained high particularly in temporary shelters and centralized relief kitchens. Susceptibility of house fly, Musca domestica to dichlorvos was determined in the laboratory to provide information for an effective management of this pest. Various concentrations of dichlorvos (76% EC) viz., 0.1, 0.2, 0.4, 0.6 and 0.8microg (a.i.) per fly, were tested using topical application against F(1) progenies of house flies collected 12 months after insecticide applications from different habitats in the tsunami-hit coastal villages. Fly mortality was recorded at 24h post treatment. Parallel controls were maintained for comparison. Mortality of the house flies varied between 17.5% and 100% and increased with an increase in dosage of the insecticide. Mortality was >80% at 0.6 and 0.8microg (a.i.) per fly. The LD(50) of dichlorvos tested against flies collected from different villages varied from 0.218microg (a.i.) to 0.235microg (a.i.) per fly and the LD(90) varied from 0.574microg (a.i.) to 0.639microg (a.i.) per fly. House flies collected from a rural village, Thirukanur that had never been exposed for insecticide treatment in the past one decade, when tested, the mortality varied between 92.5% and 100% and increased with concentration of dichlorvos. Mortality was >90% from 0.2microg (a.i.) per fly and the LD(50) was 0.0399microg (a.i.)/fly, while the LD(90) was 0.1604microg (a.i.)/fly. The LD(90) values of the flies collected from the tsunami-hit villages were 3.5-3.9 times higher than that of the flies collected from Thirukanur. Fly abundance remained high in tsunami-hit villages with no marked reduction, suggesting that the flies had developed tolerance to dichlorvos. It is suggested that for an effective management of these resistant populations changing insecticides, application of unrelated insecticide, together with an appropriate environmental sanitation measure is necessary to keep the population under check.

Efficacy of 65% permethrin applied to dogs as a spot-on against Phlebotomus perniciosus.

PubMed

Molina, R; Espinosa-Góngora, C; Gálvez, R; Montoya, A; Descalzo, M A; Jiménez, M I; Dado, D; Miró, G

2012-07-06

Leishmania infantum is a protozoan parasite causing leishmaniosis, a visceral disease transmitted by the bites of sand flies. As the main reservoir of the parasite, dogs are the principal targets of control measures against this disease, which affects both humans and dogs. Several studies have revealed the usefulness of topical insecticide treatment (collars, spot-ons and sprays) in reducing the incidence and prevalence of L. infantum. The present study was designed to test the efficacy of 65% permethrin applied to dogs as a spot-on against the sand fly vector Phlebotomus perniciosus. The duration of the desired effects was also estimated to help design an optimal treatment regimen. Twelve dogs assigned to treatment (n=6) and control (n=6) groups were exposed to sand flies once a week over a seven-week period. Repellent and insecticidal efficacies were estimated and compared amongst the groups. Our findings indicate satisfactory repellent, or anti-feeding, effects lasting 3 weeks and short-term insecticidal effects lasting 2 weeks after initial application. Accordingly, we recommend the use of this product every 2-3 weeks during the active phlebotomine sand fly period to protect dogs against the bites of P. perniciosus. Copyright © 2012 Elsevier B.V. All rights reserved.

Synthetic Sex Pheromone in a Long-Lasting Lure Attracts the Visceral Leishmaniasis Vector, Lutzomyia longipalpis, for up to 12 Weeks in Brazil

PubMed Central

Bray, Daniel P.; Carter, Vicky; Alves, Graziella B.; Brazil, Reginaldo P.; Bandi, Krishna K.; Hamilton, James G. C.

2014-01-01

Current control methodologies have not prevented the spread of visceral leishmaniasis (VL) across Brazil. Here, we describe the development of a new tool for controlling the sand fly vector of the disease: a long-lasting lure, which releases a synthetic male sex pheromone, attractive to both sexes of Lutzomyia longipalpis. This device could be used to improve the effectiveness of residual insecticide spraying as a means of sand fly control, attracting L. longipalpis to insecticide-treated animal houses, where they could be killed in potentially large numbers over a number of weeks. Different lure designs releasing the synthetic pheromone (±)-9-methylgermacrene-B (CAS 183158-38-5) were field-tested in Araçatuba, São Paulo (SP). Experiments compared numbers of sand flies caught overnight in experimental chicken sheds with pheromone lures, to numbers caught in control sheds without pheromone. Prototype lures, designed to last one night, were first used to confirm the attractiveness of the pheromone in SP, and shown to attract significantly more flies to test sheds than controls. Longer-lasting lures were tested when new, and at fortnightly intervals. Lures loaded with 1 mg of pheromone did not attract sand flies for more than two weeks. However, lures loaded with 10 mg of pheromone, with a releasing surface of 15 cm2 or 7.5 cm2, attracted female L. longipalpis for up to ten weeks, and males for up to twelve weeks. Approximately five times more sand flies were caught with 7.5 cm2 10 mg lures when first used than occurred naturally in non-experimental chicken resting sites. These results demonstrate that these lures are suitably long-lasting and attractive for use in sand fly control programmes in SP. To our knowledge, this is the first sex pheromone-based technology targeting an insect vector of a neglected human disease. Further studies should explore the general applicability of this approach for combating other insect-borne diseases. PMID:24651528

Synthetic sex pheromone in a long-lasting lure attracts the visceral leishmaniasis vector, Lutzomyia longipalpis, for up to 12 weeks in Brazil.

PubMed

Bray, Daniel P; Carter, Vicky; Alves, Graziella B; Brazil, Reginaldo P; Bandi, Krishna K; Hamilton, James G C

2014-03-01

Current control methodologies have not prevented the spread of visceral leishmaniasis (VL) across Brazil. Here, we describe the development of a new tool for controlling the sand fly vector of the disease: a long-lasting lure, which releases a synthetic male sex pheromone, attractive to both sexes of Lutzomyia longipalpis. This device could be used to improve the effectiveness of residual insecticide spraying as a means of sand fly control, attracting L. longipalpis to insecticide-treated animal houses, where they could be killed in potentially large numbers over a number of weeks. Different lure designs releasing the synthetic pheromone (±)-9-methylgermacrene-B (CAS 183158-38-5) were field-tested in Araçatuba, São Paulo (SP). Experiments compared numbers of sand flies caught overnight in experimental chicken sheds with pheromone lures, to numbers caught in control sheds without pheromone. Prototype lures, designed to last one night, were first used to confirm the attractiveness of the pheromone in SP, and shown to attract significantly more flies to test sheds than controls. Longer-lasting lures were tested when new, and at fortnightly intervals. Lures loaded with 1 mg of pheromone did not attract sand flies for more than two weeks. However, lures loaded with 10 mg of pheromone, with a releasing surface of 15 cm2 or 7.5 cm2, attracted female L. longipalpis for up to ten weeks, and males for up to twelve weeks. Approximately five times more sand flies were caught with 7.5 cm2 10 mg lures when first used than occurred naturally in non-experimental chicken resting sites. These results demonstrate that these lures are suitably long-lasting and attractive for use in sand fly control programmes in SP. To our knowledge, this is the first sex pheromone-based technology targeting an insect vector of a neglected human disease. Further studies should explore the general applicability of this approach for combating other insect-borne diseases.

Purification and characterisation of proteins secreted by the entomopathogenic fungus Metarhizium anisopliae with insecticidal activity against adults of the Mediterranean fruit fly, Ceratitis capitata (Diptera: Tephritidae).

PubMed

Ortiz-Urquiza, Almudena; Garrido-Jurado, Inmaculada; Santiago-Alvarez, Cándido; Quesada-Moraga, Enrique

2009-10-01

The control of the Mediterranean fruit fly (medfly) Ceratitis capitata (Wied) is usually performed with protein bait sprays incorporating chemical insecticides that may have adverse effects on humans, non-target organisms and the environment. In recent years, scientists have sought more environmentally friendly insecticides for medfly control, such as plant- and microorganism-derived compounds. Among these compounds, entomopathogenic fungi are an unexplored source of natural insecticides. The crude soluble protein extract (CSPE) of the entomopathogenic fungus Metarhizium anisopliae (Mestch.) (strain EAMa 01/58-Su) shows chronic insecticidal activity when administered per os. Mortality in flies exhibits a dose response. The CSPE produces an antifeedant effect in adult flies, a result probably due to a progressive deterioration of the fly midgut after ingestion of the extract. Protease and temperature treatments show that insecticidal activity against C. capitata is due to proteinaceous compounds that are highly thermostable. Four monomeric proteins from this crude extract have been purified by liquid chromatography and gel electroelution. Although all four monomers seem to be involved in the insecticidal activity of the CSPE, the 15 kDa and the 11 kDa proteins appear to be mainly responsible for the observed insecticidal effect. Four new fungal proteins with insecticidal activity have been purified and identified. These proteins might be combined with insect baits for C. capitata biocontrol. Copyright 2009 Society of Chemical Industry.

Comparison of Insecticide-Treated Nets and Indoor Residual Spraying to Control the Vector of Visceral Leishmaniasis in Mymensingh District, Bangladesh

PubMed Central

Chowdhury, Rajib; Dotson, Ellen; Blackstock, Anna J.; McClintock, Shannon; Maheswary, Narayan P.; Faria, Shyla; Islam, Saiful; Akter, Tangin; Kroeger, Axel; Akhter, Shireen; Bern, Caryn

2011-01-01

Integrated vector management is a pillar of the South Asian visceral leishmaniasis (VL) elimination program, but the best approach remains a matter of debate. Sand fly seasonality was determined in 40 houses sampled monthly. The impact of interventions on Phlebotomus argentipes density was tested from 2006–2007 in a cluster-randomized trial with four arms: indoor residual spraying (IRS), insecticide-treated nets (ITNs), environmental management (EVM), and no intervention. Phlebotomus argentipes density peaked in March with the highest proportion of gravid females in May. The EVM (mud plastering of wall and floor cracks) showed no impact. The IRS and ITNs were associated with a 70–80% decrease in male and female P. argentipes density up to 5 months post intervention. Vector density rebounded by 11 months post-IRS, whereas ITN-treated households continued to show significantly lower density compared with households without intervention. Our data suggest that both IRS and ITNs may help to improve VL control in Bangladesh. PMID:21540372

Insect Biometrics: Optoacoustic Signal Processing and Its Applications to Remote Monitoring of McPhail Type Traps.

PubMed

Potamitis, Ilyas; Rigakis, Iraklis; Fysarakis, Konstantinos

2015-01-01

Monitoring traps are important components of integrated pest management applied against important fruit fly pests, including Bactrocera oleae (Gmelin) and Ceratitis capitata (Widemann), Diptera of the Tephritidae family, which effect a crop-loss/per year calculated in billions of euros worldwide. Pests can be controlled with ground pesticide sprays, the efficiency of which depends on knowing the time, location and extent of infestations as early as possible. Trap inspection is currently carried out manually, using the McPhail trap, and the mass spraying is decided based on a decision protocol. We introduce the term 'insect biometrics' in the context of entomology as a measure of a characteristic of the insect (in our case, the spectrum of its wingbeat) that allows us to identify its species and make devices to help face old enemies with modern means. We modify a McPhail type trap into becoming electronic by installing an array of photoreceptors coupled to an infrared emitter, guarding the entrance of the trap. The beating wings of insects flying in the trap intercept the light and the light fluctuation is turned to a recording. Custom-made electronics are developed that are placed as an external add-on kit, without altering the internal space of the trap. Counts from the trap are transmitted using a mobile communication network. This trap introduces a new automated remote-monitoring method different to audio and vision-based systems. We evaluate our trap in large number of insects in the laboratory by enclosing the electronic trap in insectary cages. Our experiments assess the potential of delivering reliable data that can be used to initialize reliably the spraying process at large scales but to also monitor the impact of the spraying process as it eliminates the time-lag between acquiring and delivering insect counts to a central agency.

Insect Biometrics: Optoacoustic Signal Processing and Its Applications to Remote Monitoring of McPhail Type Traps

PubMed Central

Potamitis, Ilyas; Rigakis, Iraklis; Fysarakis, Konstantinos

2015-01-01

Monitoring traps are important components of integrated pest management applied against important fruit fly pests, including Bactrocera oleae (Gmelin) and Ceratitis capitata (Widemann), Diptera of the Tephritidae family, which effect a crop-loss/per year calculated in billions of euros worldwide. Pests can be controlled with ground pesticide sprays, the efficiency of which depends on knowing the time, location and extent of infestations as early as possible. Trap inspection is currently carried out manually, using the McPhail trap, and the mass spraying is decided based on a decision protocol. We introduce the term ‘insect biometrics’ in the context of entomology as a measure of a characteristic of the insect (in our case, the spectrum of its wingbeat) that allows us to identify its species and make devices to help face old enemies with modern means. We modify a McPhail type trap into becoming electronic by installing an array of photoreceptors coupled to an infrared emitter, guarding the entrance of the trap. The beating wings of insects flying in the trap intercept the light and the light fluctuation is turned to a recording. Custom-made electronics are developed that are placed as an external add-on kit, without altering the internal space of the trap. Counts from the trap are transmitted using a mobile communication network. This trap introduces a new automated remote-monitoring method different to audio and vision-based systems. We evaluate our trap in large number of insects in the laboratory by enclosing the electronic trap in insectary cages. Our experiments assess the potential of delivering reliable data that can be used to initialize reliably the spraying process at large scales but to also monitor the impact of the spraying process as it eliminates the time-lag between acquiring and delivering insect counts to a central agency. PMID:26544845

Pulsed arc plasma jet synchronized with drop-on-demand dispenser

NASA Astrophysics Data System (ADS)

Mavier, F.; Lemesre, L.; Rat, V.; Bienia, M.; Lejeune, M.; Coudert, J.-F.

2017-04-01

This work concerns with the liquid injection in arc plasma spraying for the development of finely structured ceramics coatings. Nanostructured coatings can be now achieved with nanopowders dispersed in a liquid (SPS: Suspension Plasma Spraying) or with a salt dissolved into a liquid (SPPS: Solution Precursor Plasma Spraying) injected into the plasma jet. Controlling electric arc instabilities confined in non-transferred arc plasma torch is therefore a key issue to get reproducible coating properties. Adjustment of parameters with a mono-cathode arc plasma allows a new resonance mode called “Mosquito”. A pulsed arc plasma producing a periodic regular voltage signal with modulation of enthalpy is obtained. The basic idea is to synchronize the injection system with the arc to introduce the liquid material in each plasma oscillation in the same conditions, in order to control the plasma treatment of the material in-fly. A custom-developed pulsed arc plasma torch is used with a drop-on-demand dispenser triggered by the arc voltage. A delay is added to adjust the droplets emission time and their penetration into the plasma gusts. Indeed, the treatment of droplets is also shown to be dependent on this injection delay. A TiO2 suspension and an aqueous solution of aluminium nitrate were optimized to get ejectable inks forming individual droplets. The feasibility of the process was demonstrated for SPS and SPPS techniques. Coatings from the suspension and the solution were achieved. First synchronized sprayings show a good penetration of the droplets into the plasma. Coatings show a fine structure of cauliflowers shapes. The synchronization of the ejection allows a control of morphology and a better deposition efficiency. Further investigations will find the optimal operating parameters to show the full potential of this original liquid injection technique.

Evaluation of ULV Applications Against Old World Sand Fly (Diptera: Psychodidae) Species in Equatorial Kenya

DTIC Science & Technology

2011-01-01

patterns of UV-labeled droplets captured on cotton ribbons adjacent to sand ßy cages in spray plots did not match patterns ofmortality.Wediscuss the...untreated areas. Surprisingly, ULV active ingredient deposition inferred from patterns of UV-labeled droplets captured on cotton ribbons adjacent to...the west plot on the second spray day; looking south. Cotton droplet capture ribbons have already been attached in position between the posts at each

Environmental sanitary interventions for preventing active trachoma.

PubMed

Rabiu, Mansur; Alhassan, Mahmoud B; Ejere, Henry O D; Evans, Jennifer R

2012-02-15

Trachoma is a major cause of avoidable blindness. It is responsible for about six million blind people worldwide, mostly in the poor communities of developing countries. One of the major strategies advocated for the control of the disease is the application of various environmental sanitary measures to such communities. To assess the evidence for the effectiveness of environmental sanitary measures on the prevalence of active trachoma in endemic areas. We searched CENTRAL (which contains the Cochrane Eyes and Vision Group Trials Register) (The Cochrane Library 2011, Issue 9), MEDLINE (January 1950 to September 2011), EMBASE (January 1980 to September 2011), Latin American and Caribbean Literature on Health Sciences (LILACS) (January 1982 to September 2011), the metaRegister of Controlled Trials (mRCT) (www.controlled-trials.com) and ClinicalTrials.gov (www.clinicaltrials.gov). There were no date or language restrictions in the electronic searches for trials. The electronic databases were last searched on 23 September 2011. We checked the reference list of included trials and the Science Citation Index. We also contacted agencies, experts and researchers in trachoma control. We included randomised and quasi-randomised controlled trials comparing any form of environmental hygiene measures with no measure. These hygiene measures included fly control, provision of water and health education. Participants in the trials were people normally resident in the trachoma endemic areas. Two authors independently extracted data and assessed the quality of the included trials. Study authors were contacted for additional information. Six trials met the inclusion criteria but we did not conduct meta-analysis due to heterogeneity of the studies. We included six studies with a total of 12,294 participants from 79 communities. Two studies that assessed insecticide spray as a fly control measure found that trachoma is reduced by at least 55% to 61% with this measure compared to no intervention. However, another study did not find insecticide spray to be effective in reducing trachoma. One study found that another fly control measure, latrine provision, reduced trachoma by 29.5% compared to no intervention; this was, however, not statistically significantly different and findings have not been confirmed by a more recent study. Another study revealed that health education reduced the incidence of trachoma. These findings were not confirmed by a second study, however, which found that a modest health education programme with modest water supply did not reduce trachoma. However, all the studies have some methodological concerns. There is some evidence from two trials that insecticides are effective in reducing trachoma, however, this effect was not demonstrated in another trial that used insecticides. Two trials on latrine provision as a fly control measure have not demonstrated significant trachoma reduction. Health education had shown significant reduction of trachoma in one study but another study did not demonstrate similar findings. Generally there is a dearth of data to determine the effectiveness of all aspects of environmental sanitation in the control of trachoma.

Agricultural Aircraft Aid

NASA Technical Reports Server (NTRS)

1982-01-01

Farmers are increasingly turning to aerial applications of pesticides, fertilizers and other materials. Sometimes uneven distribution of the chemicals is caused by worn nozzles, improper alignment of spray nozzles or system leaks. If this happens, job must be redone with added expense to both the pilot and customer. Traditional pattern analysis techniques take days or weeks. Utilizing NASA's wind tunnel and computer validation technology, Dr. Roth, Oklahoma State University (OSU), developed a system for providing answers within minutes. Called the Rapid Distribution Pattern Evaluation System, the OSU system consists of a 100-foot measurement frame tied in to computerized analysis and readout equipment. System is mobile, delivered by trailer to airfields in agricultural areas where OSU conducts educational "fly-ins." A fly-in typically draws 50 to 100 aerial applicators, researchers, chemical suppliers and regulatory officials. An applicator can have his spray pattern checked. A computerized readout, available in five to 12 minutes, provides information for correcting shortcomings in the distribution pattern.

Aircraft disinsection: exposure assessment and evaluation of a new pre-embarkation method.

PubMed

Berger-Preiss, Edith; Koch, Wolfgang; Gerling, Susanne; Kock, Heiko; Klasen, Jutta; Hoffmann, Godehard; Appel, Klaus E

2006-01-01

A new "pre-embarkation" method for aircraft disinsection was investigated using two different 2% d-phenothrin containing aerosols. Five experiments in aircrafts of the type Airbus 310 (4x) and Boeing 747-400 (1x) were performed. In the absence of passengers and crew the d-phenothrin aerosol was sprayed under the seat rows and in a second step at the height of approximately 1.60 m by moving from one end of the cabin to the other. Concentration levels of d-phenothrin were determined at different time periods after application of the aerosol spray. In a B 747-400 with the air conditioning system operating the concentrations ranged between 853 and 1753 microg/m3 during and till 5 min after the beginning of spraying at different locations in the cabin. Within 5-20min after the end of the spraying concentrations of 36-205 microg/m3 and 20-40 min thereafter only ca. 1 microg d-phenothrin/m3 were detectable (average values in relation to each period of measurement). On cabin interior surfaces the median values for mainly horizontal areas ranged from 100 to 1160 ng d-phenothrin/cm2. d-Phenothrin concentrations in the air were sufficient to kill flying insects like house flies and mosquitoes within 20 min. Horizontal surfaces were 100% effective against insects up to 24 h after spraying. Doses inhaled by sprayers determined by personal measurements were calculated to be 30-235 microg d-phenothrin per 100 g spray applied (30% in the respirable fraction for Arrow Aircraft Disinsectant; 10% for Aircraft Disinsectant Denka). If passengers will board, e.g., 20 min after the end of the disinsection operation, inhalation exposure is estimated to be practically negligible. Also possible dermal exposure from residues in seats and headrests is very low for passengers during the flight. Therefore any health effects for passengers and crew members are very unlikely.

Effect of Physiological State on Female Melon Fly (Diptera: Tephritidae) Attraction to Host and Food Odor in the Field.

PubMed

Vargas, Roger I; Piñero, Jaime C; Miller, Neil W

2018-05-28

Foraging behavior of wild female melon fly, Bactrocera (Zeugodacus) cucurbitae Coquillett, a worldwide pest of economically important cucurbit crops, was examined through mark and recapture studies in both wild (Kona: dominated by the invasive weed ivy gourd, Coccinea grandis [L.] Voigt [Cucurbitaceae]), and cultivated (Kapoho: dominated by papaya, Carica papaya L. [Caricaceae] orchards) habitats on Hawaii Island. In particular, the extent to which wild melon flies and color-marked F2 females responded to cucumber odor and Solulys yeast hydrolysate laced with ammonium acetate (1%, wt/vol) according to sexual maturity stage and degree of protein hunger was documented. Kona results indicated that more wild and color-marked F2 females responded to cucumber (Cucumis sativus L. [Cucurbitaceae]) odor than to protein odor with the exception of captured wild flies without eggs, which responded similarly to protein bait and cucumber odor. Results with captured wild females and color-marked F2 females in Kapoho suggested a significant preference for cucumber odor over protein odor regardless of whether or not they had eggs in their ovaries with the exception of protein-deprived color-marked F2 females, which responded to both odors in equal numbers. Implications of these new findings based on wild melon flies in natural habitats are discussed with respect to integrated pest management control strategies with protein bait sprays used in Hawaii. The possibility of adding cucurbit volatiles to protein-based baits is discussed.

Molecular and biochemical characterization of a sand fly population from Sri Lanka: evidence for insecticide resistance due to altered esterases and insensitive acetylcholinesterase.

PubMed

Surendran, S N; Karunaratne, S H P P; Adams, Z; Hemingway, J; Hawkes, N J

2005-08-01

With an increasing incidence of cutaneous leishmaniasis in Sri Lanka, particularly in northern provinces, insecticide-mediated vector control is under consideration. Optimizing such a strategy requires the characterization of sand fly populations in target areas with regard to species composition and extant resistance, among other parameters. Sand flies were collected by human bait and cattle-baited net traps on Delft Island, used as an illegal transit location by many refugees returning to the north of Sri Lanka from southern India where leishmaniasis is endemic. For species identification, genomic DNA was extracted and a fragment of the ribosomal 18S gene amplified. The sequence from all flies analysed matched that of Phlebotomus argentipes Annandale & Brunetti, the primary vector in India and the most likely vector in Sri Lanka. Independent morphological analysis also identified P. argentipes. To establish the current susceptibility status of vector species, data were obtained at the biochemical level, from which potential cross-resistance to alternative insecticides can be predicted. The Delft Island collection was assayed for the activities of four enzyme systems involved in insecticide resistance (acetylcholinesterase, non-specific carboxylesterases, glutathione-S-transferases and cytochrome p450 monooxygenases), establishing baselines against which subsequent collections can be evaluated. There was preliminary evidence for elevated esterases and altered acetylcholinesterase in this population, the first report of these resistance mechanisms in sand flies to our knowledge, which probably arose from the malathion-based spraying regimes of the Anti-Malarial Campaign.

Effect of GF-120 (Spinosad) Aerial Sprays on Colonies of the Stingless Bee Scaptotrigona mexicana (Hymenoptera: Apidae) and the Honey Bee (Hymenoptera: Apidae).

PubMed

Gómez-Escobar, Enoc; Liedo, Pablo; Montoya, Pablo; Méndez-Villarreal, Agustín; Guzmán, Miguel; Vandame, Rémy; Sánchez, Daniel

2018-06-02

Despite their relevant contribution to the conservation of tropical ecosystems and crop productivity through pollination, the stingless bees (Apidae: Meliponini) can be considered a group of neglected species in the assessment of pesticides upon nontarget organisms. In this article, we evaluated the effect of aerial sprays of the spinosad-based fruit fly toxic bait GF-120 upon colonies of the stingless bee Scaptotrigona mexicana Guérin (Hymenoptera: Apidae), an economically important and abundant species in some landscapes of Mexico, located in mango orchards. Colonies of the honey bee Apis mellifera L. (Hymenoptera: Apidae) were used for comparison. Eight colonies (four of A. mellifera and four of S. mexicana) were moved into each of two mango orchards, one was used as a control, with no insecticide application, and other received five weekly aerial sprays of GF-120. Foraging activity and strength of colonies of both species were measured nine times over the fruiting season, previous, during and after insecticide application. We did not find a significant difference in foraging activity and strength between exposed and control colonies of A. mellifera during the observation period. However, colonies of S. mexicana seemed to be affected by the exposure, as revealed by a reduction in colony strength. However, 1 yr later, with no insecticide applications, the colonies of both species were evaluated and found to be in good conditions. Our results showed that weekly aerial sprays of GF-120 are unlikely to generate acute poisoning in both species, even if in acute toxicity tests this product has been found to be highly active.

Characteristics and reactivity of rapidly hydrated sorbent for semidry flue gas desulfurization.

PubMed

Zhang, Jie; You, Changfu; Zhao, Suwei; Chen, Changhe; Qi, Haiying

2008-03-01

Semidry flue gas desulfurization with a rapidly hydrated sorbent was studied in a pilot-scale circulating fluidized bed (CFB) experimental facility. The desulfurization efficiency was measured for various operating parameters, including the sorbent recirculation rate and the water spray method. The experimental results show that the desulfurization efficiencies of the rapidly hydrated sorbent were 1.5-3.0 times higher than a commonly used industrial sorbent for calcium to sulfur molar ratios from 1.2 to 3.0, mainly due to the higher specific surface area and pore volume. The Ca(OH)2 content in the cyclone separator ash was about 2.9% for the rapidly hydrated sorbent and was about 0.1% for the commonly used industrial sorbent, due to the different adhesion between the fine Ca(OH)2 particles and the fly ash particles, and the low cyclone separation efficiency for the fine Ca(OH)2 particles that fell off the sorbent particles. Therefore the actual recirculation rates of the active sorbent with Ca(OH)2 particles were higher for the rapidly hydrated sorbent, which also contributed to the higher desulfurization efficiency. The high fly ash content in the rapidly hydrated sorbent resulted in good operating stability. The desulfurization efficiency with upstream water spray was 10-15% higher than that with downstream water spray.

Area-wide suppression of the Mediterranean fruit fly, Ceratitis capitata, and the Oriental fruit fly, Bactrocera dorsalis, in Kamuela, Hawaii.

PubMed

Vargas, Roger I; Piñero, Jaime C; Mau, Ronald F L; Jang, Eric B; Klungness, Lester M; McInnis, Donald O; Harris, Ernest B; McQuate, Grant T; Bautista, Renato C; Wong, Lyle

2010-01-01

The United States Department of Agriculture's Agricultural Research Service initiated an area-wide fruit fly management program in Hawaii in 2000. The first demonstration site was established in Kamuela, Hawaii, USA. This paper documents suppression of the Mediterranean fruit fly, Ceratitis capitata (Wiedemann), and the oriental fruit fly, Bactrocera dorsalis (Hendel) (Diptera: Tephritidae), in a 40 km2 area containing urban, rural and agricultural zones during a 6 year period. The suppression techniques included sanitation, GF-120 NF Naturalyte Fruit Fly Bait sprays, male annihilation, Biolure traps, and parasitoids against C. capitata and B. dorsalis. In addition, small numbers of sterile males were released against B. dorsalis. Substantial reductions in fruit infestation levels were achieved for both species (90.7 and 60.7% for C. capitata and B. dorsalis, respectively) throughout the treatment period. Fruit fly captures in the 40 km2 treatment area were significantly lower during the 6 year period than those recorded in three non-treated areas. The strategy of combining suppression techniques in an area-wide approach is discussed.

Area-Wide Suppression of the Mediterranean Fruit Fly, Ceratitis capitata, and the Oriental Fruit Fly, Bactrocera dorsalis, in Kamuela, Hawaii

PubMed Central

Vargas, Roger I.; Piñero, Jaime C.; Mau, Ronald F. L.; Jang, Eric B.; Klungness, Lester M.; McInnis, Donald O.; Harris, Ernest B.; McQuate, Grant T.; Bautista, Renato C.; Wong, Lyle

2010-01-01

The United States Department of Agriculture's Agricultural Research Service initiated an area-wide fruit fly management program in Hawaii in 2000. The first demonstration site was established in Kamuela, Hawaii, USA. This paper documents suppression of the Mediterranean fruit fly, Ceratitis capitata (Wiedemann), and the oriental fruit fly, Bactrocera dorsalis (Hendel) (Diptera: Tephritidae), in a 40 km2 area containing urban, rural and agricultural zones during a 6 year period. The suppression techniques included sanitation, GF-120 NF Naturalyte Fruit Fly Bait sprays, male annihilation, Biolure® traps, and parasitoids against C. capitata and B. dorsalis. In addition, small numbers of sterile males were released against B. dorsalis. Substantial reductions in fruit infestation levels were achieved for both species (90.7 and 60.7% for C. capitata and B. dorsalis, respectively) throughout the treatment period. Fruit fly captures in the 40 km2 treatment area were significantly lower during the 6 year period than those recorded in three non-treated areas. The strategy of combining suppression techniques in an area-wide approach is discussed. PMID:20883128

Extract of the seeds of the plant Vitex agnus castus proven to be highly efficacious as a repellent against ticks, fleas, mosquitoes and biting flies.

PubMed

Mehlhorn, Heinz; Schmahl, Günter; Schmidt, Jürgen

2005-03-01

About 70 plant extracts were tested for their ability to repel the attacks of blood-sucking arthropods. It was found that a CO2 extract of the seeds of the Mediterranean plant Vitex agnus castus (monk's pepper) can be used as a spray to keep away especially Ixodes ricinus and Rhipicephalus sanguineus ticks from animals and humans for at least 6 h. In addition mosquitoes, biting flies and fleas are also repelled for about 6 h.

Seasonal Flight, Optimal Timing and Efficacy of Selected Insecticides for Cabbage Maggot (Delia radicum L., Diptera: Anthomyiidae) Control

PubMed Central

Bažok, Renata; Ceranić-Sertić, Mirna; Barčić, Jasminka Igrc; Borošić, Josip; Kozina, Antonela; Kos, Tomislav; Lemić, Darija; Čačija, Maja

2012-01-01

In order to describe seasonal flight activity of the cabbage maggot Delia radicum (L.) adults in relation to Julian days (JD), degree-day accumulations (DDA) and precipitation, flight dynamics were followed weekly with the use of yellow sticky traps (YST). Climatic data were collected and DDA were calculated using the lower developmental threshold of 4.3 °C. The efficacy of four insecticides applied either as standard foliar treatment or through dipping the seedlings before transplanting was determined. Seasonal flight activity during the cultivation season of a mid-early variety of white cabbage was correlated with DDA and JD and was characterized by having two peaks. The first peak occurred between 119 ± 7.5 JD and 125.5 ± 8 JD when DDA was 471.35 ± 74.97 °C. The second occurred between 172.8 ± 6.1 JD and 179.3 ± 6.7 JD when DDA was 1,217.28 ± 96.12 °C. The DDA, cumulative capture of flies and JD are suitable for predicting the timing of insecticide application. Spraying with insecticides should be applied when the cumulative capture of flies reaches 100 flies/YST and when DDA reaches 400 °C. If only one parameter reaches the threshold, additional visual surveys should be employed to establish the level of infestation. Insecticides were able to ensure only partial control. In the future, alternative control tactics which employ seed treatments and nonpesticide measures should be investigated in Croatia. PMID:26466723

Implication of vector characteristics of Phlebotomus argentipes in the kala-azar elimination programme in the Indian sub-continent.

PubMed

Chowdhury, Rajib; Kumar, Vijay; Mondal, Dinesh; Das, Murari Lal; Das, Pradeep; Dash, Aditya Prasad; Kroeger, Axel

2016-05-01

Visceral leishmaniasis (VL), also known as kala-azar in the Indian sub-continent (ISC), is a major public health concern in Bangladesh, India, and Nepal, where it is caused by Leishmania donovani transmitted by the sand fly Phlebotomus argentipes. Various ecological parameters including air temperature, rainfall, wind speed, relative humidity, soil moisture, pH, and organic carbon are known to influence the oviposition of female sand flies, as well as the survival and development of larvae. However, more detailed knowledge on vector behavior, such as biting times, breeding places, and preferred hosts are needed to design optimal evidence-based vector control interventions. In order to facilitate rational decisions regarding VL vector control, a systematic review was conducted to identify the prevailing practice and knowledge gaps in relation to vector bionomics and behavior. Search terms included 'sand fly bionomics', 'habitat', and 'visceral leishmaniasis/kala-azar vector control' using the Boolean operator AND to identify the country of interest, namely: Bangladesh, India, and Nepal. Both PubMed and Google search engines were used. Additional unpublished documents in the three countries were also analyzed. Information on the life cycle of VL vectors, their breeding behavior, infection rate with L. donovani, feeding behavior, and seasonal variation are useful for designing vector control operations. Unfortunately, none of the studies on the life cycle of P. argentipes was conducted in field settings of the ISC, so the publications from other locations had to be used for determining the duration of life cycle and development from egg to adult. However, information about breeding places, seasonal variation of vector densities, and 47 out of the selected 51 papers are available from the ISC and can be used for intelligent design of control operations. Vector control services should undertake routine insecticide resistance monitoring and adapt indoor residual spraying rounds to the seasonality of vector densities. Further research is needed on potential animal reservoirs for L. donovani, on the breeding habitat, and life cycle of sand flies in the ISC.

The Electronic McPhail Trap

PubMed Central

Potamitis, Ilyas; Rigakis, Iraklis; Fysarakis, Konstantinos

2014-01-01

Certain insects affect cultivations in a detrimental way. A notable case is the olive fruit fly (Bactrocera oleae (Rossi)), that in Europe alone causes billions of euros in crop-loss/per year. Pests can be controlled with aerial and ground bait pesticide sprays, the efficiency of which depends on knowing the time and location of insect infestations as early as possible. The inspection of traps is currently carried out manually. Automatic monitoring traps can enhance efficient monitoring of flying pests by identifying and counting targeted pests as they enter the trap. This work deals with the hardware setup of an insect trap with an embedded optoelectronic sensor that automatically records insects as they fly in the trap. The sensor responsible for detecting the insect is an array of phototransistors receiving light from an infrared LED. The wing-beat recording is based on the interruption of the emitted light due to the partial occlusion from insect's wings as they fly in the trap. We show that the recordings are of high quality paving the way for automatic recognition and transmission of insect detections from the field to a smartphone. This work emphasizes the hardware implementation of the sensor and the detection/counting module giving all necessary implementation details needed to construct it. PMID:25429412

Evaluation of cimi-shield knock-out bed bug eliminator against house fly (Musca domestica) adults

USDA-ARS?s Scientific Manuscript database

Cimi-Shield Knock-Out (CSKO) Bed Bug Eliminator is a green treatment labeled for use against bed bugs, carpet beetles, ants, roaches, fleas, ticks, silverfish, millipedes and centipedes. The active ingredient is soybean oil. If CSKO is formulated according to label instructions and sprayed directly ...

Evaluation of cimi-shield knock-out bed bug eliminator against house fly (Musca domestica) adults.

USDA-ARS?s Scientific Manuscript database

Cimi-Shield Knock-Out (CSKO) Bed Bug Eliminator is a green treatment labeled for use against bed bugs, carpet beetles, ants, roaches, fleas, ticks, silverfish, millipedes and centipedes. The active ingredient is soybean oil. If CSKO is formulated according to label instructions and sprayed directly ...

Larval breeding sites of Lutzomyia longipalpis (Diptera: Psychodidae) in visceral leishmaniasis endemic urban areas in Southeastern Brazil.

PubMed

Casanova, Cláudio; Andrighetti, Maria T M; Sampaio, Susy M P; Marcoris, Maria L G; Colla-Jacques, Fernanda E; Prado, Angelo P

2013-01-01

The scarcity of information on the immature stages of sand flies and their preferred breeding sites has resulted in the focus of vectorial control on the adult stage using residual insecticide house-spraying. This strategy, along with the treatment of human cases and the euthanasia of infected dogs, has proven inefficient and visceral leishmaniasis continues to expand in Brazil. Identifying the breeding sites of sand flies is essential to the understanding of the vector's population dynamic and could be used to develop novel control strategies. In the present study, an intensive search for the breeding sites of Lutzomyia longipalpis was conducted in urban and peri-urban areas of two municipalities, Promissão and Dracena, which are endemic for visceral leishmaniasis in São Paulo State, Brazil. During an exploratory period, a total of 962 soil emergence traps were used to investigate possible peridomiciliary breeding site microhabitats such as: leaf litter under tree, chicken sheds, other animal sheds and uncovered debris. A total of 160 sand flies were collected and 148 (92.5%) were L. longipalpis. In Promissão the proportion of chicken sheds positive was significantly higher than in leaf litter under trees. Chicken shed microhabitats presented the highest density of L. longipalpis in both municipalities: 17.29 and 5.71 individuals per square meter sampled in Promissão and Dracena respectively. A contagious spatial distribution pattern of L. longipalpis was identified in the emergence traps located in the chicken sheds. The results indicate that chicken sheds are the preferential breeding site for L. longipalpis in the present study areas. Thus, control measures targeting the immature stages in chicken sheds could have a great effect on reducing the number of adult flies and consequently the transmission rate of Leishmania (Leishmania) infantum chagasi.

Larval Breeding Sites of Lutzomyia longipalpis (Diptera: Psychodidae) in Visceral Leishmaniasis Endemic Urban Areas in Southeastern Brazil

PubMed Central

Casanova, Cláudio; Andrighetti, Maria T. M.; Sampaio, Susy M. P.; Marcoris, Maria L. G.; Colla-Jacques, Fernanda E.; Prado, Ângelo P.

2013-01-01

Background The scarcity of information on the immature stages of sand flies and their preferred breeding sites has resulted in the focus of vectorial control on the adult stage using residual insecticide house-spraying. This strategy, along with the treatment of human cases and the euthanasia of infected dogs, has proven inefficient and visceral leishmaniasis continues to expand in Brazil. Identifying the breeding sites of sand flies is essential to the understanding of the vector's population dynamic and could be used to develop novel control strategies. Methodology/Principal finding In the present study, an intensive search for the breeding sites of Lutzomyia longipalpis was conducted in urban and peri-urban areas of two municipalities, Promissão and Dracena, which are endemic for visceral leishmaniasis in São Paulo State, Brazil. During an exploratory period, a total of 962 soil emergence traps were used to investigate possible peridomiciliary breeding site microhabitats such as: leaf litter under tree, chicken sheds, other animal sheds and uncovered debris. A total of 160 sand flies were collected and 148 (92.5%) were L. longipalpis. In Promissão the proportion of chicken sheds positive was significantly higher than in leaf litter under trees. Chicken shed microhabitats presented the highest density of L. longipalpis in both municipalities: 17.29 and 5.71 individuals per square meter sampled in Promissão and Dracena respectively. A contagious spatial distribution pattern of L. longipalpis was identified in the emergence traps located in the chicken sheds. Conclusion The results indicate that chicken sheds are the preferential breeding site for L. longipalpis in the present study areas. Thus, control measures targeting the immature stages in chicken sheds could have a great effect on reducing the number of adult flies and consequently the transmission rate of Leishmania (Leishmania) infantum chagasi. PMID:24069494

Implication of vector characteristics of Phlebotomus argentipes in the kala-azar elimination programme in the Indian sub-continent

PubMed Central

Chowdhury, Rajib; Kumar, Vijay; Mondal, Dinesh; Das, Murari Lal; Das, Pradeep; Dash, Aditya Prasad

2016-01-01

Background Visceral leishmaniasis (VL), also known as kala-azar in the Indian sub-continent (ISC), is a major public health concern in Bangladesh, India, and Nepal, where it is caused by Leishmania donovani transmitted by the sand fly Phlebotomus argentipes. Various ecological parameters including air temperature, rainfall, wind speed, relative humidity, soil moisture, pH, and organic carbon are known to influence the oviposition of female sand flies, as well as the survival and development of larvae. However, more detailed knowledge on vector behavior, such as biting times, breeding places, and preferred hosts are needed to design optimal evidence-based vector control interventions. Methods In order to facilitate rational decisions regarding VL vector control, a systematic review was conducted to identify the prevailing practice and knowledge gaps in relation to vector bionomics and behavior. Search terms included ‘sand fly bionomics’, ‘habitat’, and ‘visceral leishmaniasis/kala-azar vector control’ using the Boolean operator AND to identify the country of interest, namely: Bangladesh, India, and Nepal. Both PubMed and Google search engines were used. Additional unpublished documents in the three countries were also analyzed. Results Information on the life cycle of VL vectors, their breeding behavior, infection rate with L. donovani, feeding behavior, and seasonal variation are useful for designing vector control operations. Unfortunately, none of the studies on the life cycle of P. argentipes was conducted in field settings of the ISC, so the publications from other locations had to be used for determining the duration of life cycle and development from egg to adult. However, information about breeding places, seasonal variation of vector densities, and 47 out of the selected 51 papers are available from the ISC and can be used for intelligent design of control operations. Conclusion Vector control services should undertake routine insecticide resistance monitoring and adapt indoor residual spraying rounds to the seasonality of vector densities. Further research is needed on potential animal reservoirs for L. donovani, on the breeding habitat, and life cycle of sand flies in the ISC. PMID:27376500

Pyrethroid Treatment of Cattle for Tsetse Control: Reducing Its Impact on Dung Fauna

PubMed Central

Vale, Glyn A.; Hargrove, John W.; Chamisa, Andrew; Grant, Ian F.; Torr, Stephen J.

2015-01-01

Background African trypansomiases of humans and animals can be controlled by attacking the vectors, various species of tsetse fly. Treatment of cattle with pyrethroids to kill tsetse as they feed is the most cost-effective method. However, such treatments can contaminate cattle dung, thereby killing the fauna which disperse the dung and so play an important role in soil fertility. Hence there is a need to identify cost-effective methods of treating cattle with minimal impact on dung fauna. Methodology/Principal Findings We used dung beetles to field bioassay the levels of dung contamination following the use of spray and pour-on formulations of deltamethrin, applied to various parts of the body of cattle in Zimbabwe. Results suggested that dung was contaminated by contact with insecticide on the body surface as the cattle defecated, and by ingestion of insecticide as the cattle licked themselves. Death of dung beetles was reduced to negligible levels by using only the spray and applying it to the legs and belly or legs alone, i.e., places where most tsetse feed. Conclusion/Significance The restricted applications suitable for minimising the impact on dung fauna have the collateral benefits of improving the economy and convenience of cattle treatments for tsetse control. The demonstration of collateral benefits is one of the surest ways of promoting environmentally friendly procedures. PMID:25738836

Tank Tests of Models of Flying Boat Hulls Having Longitudinal Steps

NASA Technical Reports Server (NTRS)

Allison, John M; Ward, Kenneth E

1936-01-01

Four models with longitudinal steps on the forebody were developed by modification of a model of a conventional hull and were tested in the National Advisory Committee for Aeronautics (NACA) tank. Models with longitudinal steps were found to have smaller resistance at high speed and greater resistance at low speed than the parent model that had the same afterbody but a conventional V-section forebody. The models with a single longitudinal step had better performance at hump speed and as low high-speed resistance except at very light loads. Spray strips at angles from 0 degrees to 45 degrees to the horizontal were fitted at the longitudinal steps and at the chine on one of the two step models having two longitudinal steps. The resistance and the height of the spray were less with each of the spray strips than without; the most favorable angle was found to lie between 15 degrees and 30 degrees.

Spray-dry desulfurization of flue gas from heavy oil combustion.

PubMed

Scala, Fabrizio; Lancia, Amedeo; Nigro, Roberto; Volpicelli, Gennaro

2005-01-01

An experimental investigation on sulfur dioxide removal in a pilot-scale spray dryer from the flue gas generated by combustion of low-sulfur (S) heavy oil is reported. A limewater slurry was sprayed through an ultrasonic two-fluid atomizer in the spray-dry chamber, and the spent sorbent was collected downstream in a pulse-jet baghouse together with fly ash. Flue gas was sampled at different points to measure the desulfurization efficiency after both the spray-dry chamber and the baghouse. Parametric tests were performed to study the effect of the following variables: gas inlet temperature, difference between gas outlet temperature and adiabatic saturation temperature, lime-to-S ratio, and average size of lime particles in the slurry. Results indicated that spray drying is an effective technology for the desulfurization of low-S fuel oil flue gas, provided operating conditions are chosen carefully. In particular, the lowest gas inlet and outlet temperatures compatible with baghouse operation should be selected, as should a sufficiently high lime-to-S ratio. The attainment of a small lime particle size in the slurry is critical for obtaining a high desulfurization efficiency. A previously presented spray-dry flue gas desulfurization model was used to simulate the pilot-scale desulfurization tests, to check the ability of the model to predict the S capture data and its usefulness as a design tool, minimizing the need for pilot-scale experimentation. Comparison between model and experimental results was fairly good for the whole range of calcium/S ratios considered.

Degradation of TBC Systems in Environments Relevant to Advanced Gas Turbines for IGCC Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gleeson, Brian

2014-09-30

Air plasma sprayed (APS) thermal barrier coatings (TBCs) are used to provide thermal insulation for the hottest components in gas turbines. Zirconia stabilized with 7wt% yttria (7YSZ) is the most common ceramic top coat used for turbine blades. The 7YSZ coating can be degraded from the buildup of fly-ash deposits created in the power-generation process. Fly ash from an integrated gasification combined cycle (IGCC) system can result from coal-based syngas. TBCs are also exposed to harsh gas environments containing CO 2, SO 2, and steam. Degradation from the combined effects of fly ash and harsh gas atmospheres has the potentialmore » to severely limit TBC lifetimes. The main objective of this study was to use lab-scale testing to systematically elucidate the interplay between prototypical deposit chemistries (i.e., ash and its constituents, K 2SO 4, and FeS) and environmental oxidants (i.e., O 2, H 2O and CO 2) on the degradation behavior of advanced TBC systems. Several mechanisms of early TBC failure were identified, as were the specific fly-ash constituents responsible for degradation. The reactivity of MCrAlY bondcoats used in TBC systems was also investigated. The specific roles of oxide and sulfate components were assessed, together with the complex interplay between gas composition, deposit chemistry and alloy reactivity. Bondcoat composition design strategies to mitigate corrosion were established, particularly with regard to controlling phase constitution and the amount of reactive elements the bondcoat contains in order to achieve optimal corrosion resistance.« less

A network meta-analysis provides new insight into fungicide scheduling for the control of Botrytis cinerea in vineyards.

PubMed

González-Domínguez, Elisa; Fedele, Giorgia; Caffi, Tito; Delière, Laurent; Sauris, Pierre; Gramaje, David; Ramos-Sáez de Ojer, José Luis; Díaz-Losada, Emilia; Díez-Navajas, Ana M; Bengoa, Paul; Rossi, Vittorio

2018-06-09

Control of Botrytis bunch rot (BBR) is currently based on the application of fungicides at four timings corresponding to specific growth stages of vines: end of flowering (A), pre-bunch closure (B), veraison (C) and before harvest (D). The current research provides a network meta-analysis of 116 studies conducted between 1963 and 2016 in nine countries, in which 14 strategies (based on combinations of 1, 2, 3, or 4 sprays applied in A, B, C, and/or D) were compared. When a 1-spray strategy was applied, BBR control was more effective with sprays applied in A, C, or D than B. With a 2-spray strategy, strategy AC provided similar control as strategy BC; strategy CD also provided good control. For a 3-spray strategy, the best disease control was consistently obtained with strategy ACD. Four sprays strategy ABCD provided the best control but often involved needless sprays so that the routine application of four sprays is not justified. Spraying at timing A seems to be very important for achieving efficient and flexible disease control. Flexibility is reduced by spraying at timing B rather than A. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Electrostatic spraying in the chemical control of Triozoida limbata (Enderlein) (Hemiptera: Triozidae) in guava trees (Psidium guajava L.).

PubMed

Tavares, Rafael M; Cunha, João Par; Alves, Thales C; Bueno, Mariana R; Silva, Sérgio M; Zandonadi, César Hs

2017-06-01

Owing to the difficulty in reaching targets during pesticide applications on guava trees, it is important to evaluate new technologies that may improve pest management. In electrostatic spraying, an electric force is added to the droplets to control their movements such that they are efficiently directed to the target. The present study evaluated the performance of electrostatic and non-electrostatic spraying in the control of the guava psyllid, the deposition of the spray mixture on the leaves and the losses to the soil. The deposition of the spray mixture was up to 2 times greater when using electrostatic spraying in comparison with non-electrostatic application. The losses of the spray mixture to the soil were up to 4 times smaller with the electrostatic spraying. Electrostatic spraying had better control of the psyllid. It was possible to reduce the volume rate of application with electrostatic spraying without adversely affecting the control of the guava psyllid. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Aircraft disinsecting: the effectiveness of Freon-based and water-based phenothrin and permethrin aerosols*

PubMed Central

Sullivan, W. N.; Cawley, B. M.; Schechter, M. S.; Morgan, N. O.; Pal, R.

1979-01-01

In Miami, Florida, USA, passenger compartments of jet aircraft were disinsected at ”blocks away”. An application of a 20 g/litre Freon-based or water-based permethrin formulation at 35 mg of aerosol per 100 m3 was 100% effective against caged mosquitos and flies. The flammability hazard of the sprays from water-based hydrocarbon aerosols was evaluated. PMID:316739

The selection of flying roller as an effort to increase the power of scooter-matic as the main power of centrifugal pump for fire fighter motor cycle

NASA Astrophysics Data System (ADS)

Hadi Sutrisno, Himawan

2018-03-01

In densely populated settlements, fires often occur and cause losses. In some instances, the process of the occurrence of fires takes place so quickly that to reduce and avoid the occurrence of a fire disaster effort is required in accordance with the existing environmental condition. Fire fighter motorcycle by using motorcycle scooter-matic is considered suitable as one alternative to combating fire hazard in densely populated residential settlements. The use of motorcycle engines as the driving force of the pump often leads to unstable and not optimum power. Thus, the water spray on the centrifugal pump also becomes not maximum. To increase the engine power at scooter-matic engine idle rotation (700-2000 rpm), then the flying roller replacement with certain mass weight becomes an option. By selecting a 10 to 14 gram flying roller mass, the power analysis using a dynotest engine produces several variations. Of the calculation, the mass of a 14 gram flying roller provides a significant increase in motor power on the upper rotation. Meanwhile, on the lower power rotation using a flying roller with a mass of 10 grams provides an increase in power compared to a standard flying roller on a scooter matic motor engine. As a reference to the use of scooter-matic motor power as the pump power, the result of use of the flying roller with a mass of 10 grams becomes the best option.

Changes in waste stabilisation pond performance resulting from the retrofit of activated sludge treatment upstream: part II--Management and operating issues.

PubMed

Sweeney, D G; O'Brien, M J; Cromar, N J; Fallowfield, H J

2005-01-01

Bolivar Wastewater Treatment Plant (WWTP) was originally commissioned with trickling filter secondary treatment, followed by waste stabilisation pond (WSP) treatment and marine discharge. In 1999, a dissolved air flotation/filtration (DAFF) plant was commissioned to treat a portion of the WSP effluent for horticultural reuse. In 2001, the trickling filters were replaced with activated sludge treatment. A shift in WSP ecology became evident soon after this time, characterised by a statistically significant reduction in algal counts in the pond effluent, and increased variability in algal counts and occasional population crashes in the ponds. While the photosynthetic capacity of the WSPs has been reduced, the concomitant reduction in organic loading has meant that the WSPs have not become overloaded. As a result of the improvement in water quality leaving the ponds, significant cost savings and improved product water quality have been realised in the subsequent DAFF treatment stage. A number of operating issues have arisen from the change, however, including the re-emergence of a midge fly nuisance at the site. Control of midge flies using chemical spraying has negated the cost savings realised in the DAFF treatment stage. While biomanipulation of the WSP may provide a less aggressive method of midge control, this case demonstrates the difficulty of predicting in advance all ramifications of a retrospective process change.

Evidence of Coal-Fly-Ash Toxic Chemical Geoengineering in the Troposphere: Consequences for Public Health.

PubMed

Herndon, J Marvin

2015-08-11

The widespread, intentional and increasingly frequent chemical emplacement in the troposphere has gone unidentified and unremarked in the scientific literature for years. The author presents evidence that toxic coal combustion fly ash is the most likely aerosolized particulate sprayed by tanker-jets for geoengineering, weather-modification and climate-modification purposes and describes some of the multifold consequences on public health. Two methods are employed: (1) Comparison of 8 elements analyzed in rainwater, leached from aerosolized particulates, with corresponding elements leached into water from coal fly ash in published laboratory experiments, and (2) Comparison of 14 elements analyzed in dust collected outdoors on a high-efficiency particulate air (HEPA) filter with corresponding elements analyzed in un-leached coal fly ash material. The results show: (1) the assemblage of elements in rainwater and in the corresponding experimental leachate are essentially identical. At a 99% confidence interval, they have identical means (T-test) and identical variances (F-test); and (2) the assemblage of elements in the HEPA dust and in the corresponding average un-leached coal fly ash are likewise essentially identical. The consequences on public health are profound, including exposure to a variety of toxic heavy metals, radioactive elements, and neurologically-implicated chemically mobile aluminum released by body moisture in situ after inhalation or through transdermal induction.

Remotely controlled spray gun

NASA Technical Reports Server (NTRS)

Cunningham, William C. (Inventor)

1987-01-01

A remotely controlled spray gun is described in which a nozzle and orifice plate are held in precise axial alignment by an alignment member, which in turn is held in alignment with the general outlet of the spray gun by insert. By this arrangement, the precise repeatability of spray patterns is insured.

European Scientific Notes. Volume 36, Number 2,

DTIC Science & Technology

1982-02-28

colleagues at creases in process complexity and cost of the the University College of Swansea have con- product . So far, aluminum alloy, steel, and...associated with metal spray processing can stream of metal impinging on a disk rotating at impart to the solidified product . 3,000 to 5,000 rpm is...the point. Indeed, the pilot can simplicity, economy , stand-alone operability, often "fly the point" as the approach continues, portability, and

Tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise - NACA model 35 series

NASA Technical Reports Server (NTRS)

Dawson, John R

1936-01-01

The results of tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise are given in charts and are compared with results from tests of more conventional hulls. Increasing the angle of dead rise from 15 to 25 degrees: had little effect on the hump resistance; increased the resistance throughout the planning range; increased the best trim angle; reduced the maximum positive trimming moment required to obtain best trim angle; and had but a slight effect on the spray characteristics. For approximately the same angles of dead rise the resistance of the pointed-step hulls were considerably lower at high speeds than those of the more conventional hulls.

Evidence of Coal-Fly-Ash Toxic Chemical Geoengineering in the Troposphere: Consequences for Public Health

PubMed Central

Herndon, J. Marvin

2015-01-01

The widespread, intentional and increasingly frequent chemical emplacement in the troposphere has gone unidentified and unremarked in the scientific literature for years. The author presents evidence that toxic coal combustion fly ash is the most likely aerosolized particulate sprayed by tanker-jets for geoengineering, weather-modification and climate-modification purposes and describes some of the multifold consequences on public health. Two methods are employed: (1) Comparison of 8 elements analyzed in rainwater, leached from aerosolized particulates, with corresponding elements leached into water from coal fly ash in published laboratory experiments, and (2) Comparison of 14 elements analyzed in dust collected outdoors on a high-efficiency particulate air (HEPA) filter with corresponding elements analyzed in un-leached coal fly ash material. The results show: (1) the assemblage of elements in rainwater and in the corresponding experimental leachate are essentially identical. At a 99% confidence interval, they have identical means (T-test) and identical variances (F-test); and (2) the assemblage of elements in the HEPA dust and in the corresponding average un-leached coal fly ash are likewise essentially identical. The consequences on public health are profound, including exposure to a variety of toxic heavy metals, radioactive elements, and neurologically-implicated chemically mobile aluminum released by body moisture in situ after inhalation or through transdermal induction. PMID:26270671

DOE Office of Scientific and Technical Information (OSTI.GOV)

JOHNSON, A.R.

Biological control is any activity taken to prevent, limit, clean up, or remediate potential environmental, health and safety, or workplace quality impacts from plants, animals, or microorganisms. At Hanford the principal emphasis of biological control is to prevent the transport of radioactive contamination by biological vectors (plants, animals, or microorganisms), and where necessary, control and clean up resulting contamination. Other aspects of biological control at Hanford include industrial weed control (e.g.; tumbleweeds), noxious weed control (invasive, non-native plant species), and pest control (undesirable animals such as rodents and stinging insects; and microorganisms such as molds that adversely affect the qualitymore » of the workplace environment). Biological control activities may be either preventive (apriori) or in response to existing contamination spread (aposteriori). Surveillance activities, including ground, vegetation, flying insect, and other surveys, and apriori control actions, such as herbicide spraying and placing biological barriers, are important in preventing radioactive contamination spread. If surveillance discovers that biological vectors have spread radioactive contamination, aposteriori control measures, such as fixing contamination, followed by cleanup and removal of the contamination to an approved disposal location are typical response functions. In some cases remediation following the contamination cleanup and removal is necessary. Biological control activities for industrial weeds, noxious weeds and pests have similar modes of prevention and response.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

JOHNSON, A.R.

Biological control is any activity taken to prevent, limit, clean up, or remediate potential environmental, health and safety, or workplace quality impacts from plants, animals, or microorganisms. At Hanford the principal emphasis of biological control is to prevent the transport of radioactive contamination by biological vectors (plants, animals, or microorganisms), and where necessary, control and clean up resulting contamination. Other aspects of biological control at Hanford include industrial weed control (e.g.; tumbleweeds), noxious weed control (invasive, non-native plant species), and pest control (undesirable animals such as rodents and stinging insects, and microorganisms such as molds that adversely affect the qualitymore » of the workplace environment). Biological control activities may be either preventive (a priori) or in response to existing contamination spread (a posteriori). Surveillance activities, including ground, vegetation, flying insect, and other surveys, and a priori control actions, such as herbicide spraying and placing biological barriers, are important in preventing radioactive contamination spread. If surveillance discovers that biological vectors have spread radioactive contamination, a posteriori control measures, such as fixing contamination, followed by cleanup and removal of the contamination to an approved disposal location are typical response functions. In some cases remediation following the contamination cleanup and removal is necessary. Biological control activities for industrial weeds, noxious weeds and pests have similar modes of prevention and response.« less

Zinc thermal spray coatings for reinforced concrete: An AWS process standard

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sulit, R.A.

Zinc and aluminum thermal spray coatings (TSC) have been used for lining concrete weir in Great Britain since the 1950`s to maintain the dimensions of the weir for flow control concomitant with reduced wear and erosion of the concrete surfaces. This paper reports the development and the content of the ANSI/AWS C2.20-XX standard for the application of An TSC on concrete using flame and arc spray processes. This standard is formatted as an industrial process instruction: job description; safety; feedstock materials; equipment; a step-by-step method for surface preparation, thermal spraying; quality control; repair and maintenance of surface preparation, thermal spraying;more » quality control; repair and maintenance of Zn TSC on concrete; and a Job Control Record. Job planning and training and certification requirements are presented for An TSC inspectors and thermal spray operators. Four annexes are included in the standard: (a) historical summary of Zn TSC on concrete (b) sample job control record; (c) thermal spray operator qualification; and (d) portable adhesion testing for An TSC on concrete. This standard is based on the current literature and industrial equipment, process, and practices.« less

Neem derivatives are not effective as toxic bait for tephritid fruit flies.

PubMed

Silva, M A; Bezerra-Silva, G C D; Vendramim, J D; Mastrangelo, T; Forim, M R

2013-08-01

Neem derivatives have been widely touted as replacements for pesticides. A feasible replacement of synthetic insecticides in the management of fruit flies could be to use neem products in baits. This study evaluated the bioactivity of neem (Azadirachta indica A. Juss) derivatives in bait for adults of Anastrepha fraterculus (Wiedemann) and Ceratitis capitata (Wiedemann). The estimated LCs50 values for A. fraterculus and C. capitata were 7,522 ppm (18.40 ppm of azadirachtin) and 1,368 ppm (3.35 ppm of azadirachtin), respectively, using an aqueous extract of neem seeds in bait after 10 d of experimentation. No significant differences in the mortality of A. fraterculus and C. capitata adults exposed to baits made from different extracts and neem oil were observed after 3 h or 2 or 6 d; differences among the treatments were observed only on the 10th day of the evaluation. We conclude that neem derivatives applied as a bait spray over citrus plants did not demonstrate a toxic effect on A. fraterculus and C. capitata. The reasons for the low efficacy of the neem bait on Tephritid fruit flies are discussed.

The influence of menthol on thermoregulation and perception during exercise in warm, humid conditions.

PubMed

Gillis, D Jason; House, James R; Tipton, Michael J

2010-10-01

Menthol has recently been added to various cooling products that claim to enhance athletic performance. This study assessed the effect of two such solutions during exercise in warm, humid conditions. Twelve participants (22 ± 2.9 years; VO2peak 47.4 ± 6.2 mL kg(-1) min(-1)) completed a peak power (PO(peak)) test and three separate exercise bouts in 30°C and 70% relative humidity after being sprayed with 100 mL of water containing either 0.05 or 0.2% l-menthol, or a control spray. During each trial, participants underwent 15 min of rest, spraying, 15 min of rest and 45 min of exercise at 45% of PO(peak). The following variables were measured: rectal temperature (T (re)), sweat rate (SR), skin blood flow (SBF), heart rate (HR), thermal comfort (TC) and sensation (TS) votes, irritation (IRR) and rating of perceived exertion (RPE). Mean skin (MST) and body temperatures (Tbody) were calculated. There was no significant difference in MST, Tbody SR, SBF, HR, TC or RPE between conditions. Spraying with 0.2% menthol significantly (P < 0.05) elevated T (re) by 0.2°C compared to the other conditions. Both menthol sprays caused participants to feel significantly cooler than control spraying (P = 0.001), but 0.2% spraying induced significantly cooler sensations (P = 0.01) than 0.05% spraying. Both menthol sprays induced greater irritation (P < 0.001) than control spraying. These findings suggest that 0.05% menthol spraying induced cooler upper body sensations without measurable thermoregulatory impairment. T (re) was significantly elevated with 0.2% spraying. Irritation persisted with both menthol sprays while TC remained unchanged, suggesting a causal relationship. The use in sport of a spray similar to those tested here remains equivocal.

Diabetes Insipidus—Treatment with 8-Lysine Vasopressin in a Nasal Spray

PubMed Central

Chirman, Samuel B.; Kinsell, Laurance W.

1964-01-01

Synthetic 8-lysine vasopressin administered as a nasal spray to three patients with diabetes insipidus resulted in excellent control in one. In the other two it was of some value as therapy supplemental to pitressin tannate in oil. The patient who was adequately controlled with “spray therapy” alone required the sprays every three hours during the day, but none during the night. PMID:14179526

Open-air sprays for capturing and controlling airborne float coal dust on longwall faces

PubMed Central

Beck, T.W.; Seaman, C.E.; Shahan, M.R.; Mischler, S.E.

2018-01-01

Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. PMID:29348700

Open-air sprays for capturing and controlling airborne float coal dust on longwall faces.

PubMed

Beck, T W; Seaman, C E; Shahan, M R; Mischler, S E

2018-01-01

Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening.

Awareness and Need for Knowledge of Health and Safety among Dairy Farmers Interviewed in Uganda.

PubMed

Lunner-Kolstrup, Christina; Ssali, Tonny Kiggundu

2016-01-01

Safe working conditions are essential for healthy living and for ensuring food security among farmers and farm communities in developing countries. There is limited research on this topic, and documentation is essential to understand and change patterns of human health and safety. In May 2014, six male and female farmers on four dairy farms in Uganda and a female veterinarian were interviewed about their awareness and attitudes to agricultural risk factors, health, and safety. In addition, transect walks were conducted on the four dairy farms. The dairy farmers reported health and safety concerns, e.g., diarrhea, coughs, fever, cuts while using machetes in plantations, bruises when handling animals, and dizziness and poisoning symptoms from using different agrochemicals, and considered these an occupational hazard. The most important topic mentioned was the use of agrochemicals and drugs on livestock. The farmers spray their animals with insecticides to prevent ticks, lice, tsetse flies, and other biting nuisance flies, using a backpack or hand sprayer. Spraying is conducted without personal protection equipment, which is considered too expensive and difficult to obtain. The farmers reported that they usually feel dizzy, vomit, and have pain and a burning feeling in their face and eyes after spraying. The symptoms are sometimes so severe that they require treatment. In such cases, the farmers buy medication without a prescription at the local drugstore, where the storekeeper often has limited or no knowledge of agrochemicals or drugs except for dosage. Agricultural health and safety training in the region is non-existent, and the farmers expressed a need and desire for improvements in this area. The level of knowledge and awareness of agricultural health and safety risks, disease, and injury prevention among the Ugandan dairy farmers interviewed was low. The farmers mentioned few agriculture-related complaints, injuries, or diseases except poisoning from using agrochemicals. Training on health and safety in Ugandan agriculture is urgently needed.

USERS GUIDE FOR THE CONVERSION OF NAVY PAINT SPRAY BOOTH PARTICULATE EMISSION CONTROL SYSTEMS FROM WET TO DRY OPERATION

EPA Science Inventory

The report is a guide or convrting U.S. Navy paint spray booth particulate emission control systems from wet to dry operation. The use of water curtains for air pollution control of paint spray booths is considered a major source of water and solid waste pol-lution from industria...

77 FR 40550 - Approval and Promulgation of Air Quality Implementation Plans; Maryland; Revision for the Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-10

... filtered spray booth and enclosed spray gun cleaner. Maryland's 1997 SIP-approved regulation COMAR 26.11.19... equipment and materials storage such as spray booths, spray guns, and sealed containers for cleaning rags... standards include procedures for cleaning the spray gun equipment for applying automotive coatings. Affected...

Early change in thermal perception is not a driver of anticipatory exercise pacing in the heat.

PubMed

Barwood, Martin James; Corbett, Jo; White, Danny; James, Jason

2012-10-01

Initial power output declines significantly during exercise in hot conditions on attaining a rapid increase in skin temperature when exercise commences. It is unclear whether this initial reduced power is mediated consciously, through thermal perceptual cues, or is a subconscious process. The authors tested the hypothesis that improved thermal perception (feeling cooler and more comfortable) in the absence of a change in thermal state (ie, similar deep-body and skin temperatures between spray conditions) would alter pacing and 40 km cycling time trial (TT) performance. Eleven trained participants (mean (SD): age 30 (8.1) years; height 1.78 (0.06) m; mass 76.0 (8.3) kg) completed three 40 km cycling TTs in standardised conditions (32°C, 50% RH) with thermal perception altered prior to exercise by application of cold-receptor-activating menthol spray (MENTHOL SPRAY), in contrast to a separate control spray (CONTROL SPRAY) and no spray control (CON). Thermal perception, perceived exertion, thermal responses and cycling TT performance were measured. MENTHOL SPRAY induced feelings of coolness and improved thermal comfort before and during exercise. Skin temperature profile at the start of exercise was similar between sprays (CON-SPRAY 33.3 (1.1)°C and MENTHOL SPRAY 33.4 (0.4)°C, but different to CON 34.5 (0.5)°C), but there was no difference in the pacing strategy adopted. There was no performance benefit using MENTHOL SPRAY; cycling TT completion time for CON is 71.58 (6.21) min, for CON-SPRAY is 70.94 (6.06) min and for MENTHOL SPRAY is 71.04 (5.47) min. The hypothesis is rejected. Thermal perception is not a primary driver of early pacing during 40 km cycling TT in hot conditions in trained participants.

Effectiveness of Large-Scale Chagas Disease Vector Control Program in Nicaragua by Residual Insecticide Spraying Against Triatoma dimidiata.

PubMed

Yoshioka, Kota; Nakamura, Jiro; Pérez, Byron; Tercero, Doribel; Pérez, Lenin; Tabaru, Yuichiro

2015-12-01

Chagas disease is one of the most serious health problems in Latin America. Because the disease is transmitted mainly by triatomine vectors, a three-phase vector control strategy was used to reduce its vector-borne transmission. In Nicaragua, we implemented an indoor insecticide spraying program in five northern departments to reduce house infestation by Triatoma dimidiata. The spraying program was performed in two rounds. After each round, we conducted entomological evaluation to compare the vector infestation level before and after spraying. A total of 66,200 and 44,683 houses were sprayed in the first and second spraying rounds, respectively. The entomological evaluation showed that the proportion of houses infested by T. dimidiata was reduced from 17.0% to 3.0% after the first spraying, which was statistically significant (P < 0.0001). However, the second spraying round did not demonstrate clear effectiveness. Space-time analysis revealed that reinfestation of T. dimidiata is more likely to occur in clusters where the pre-spray infestation level is high. Here we discuss how large-scale insecticide spraying is neither effective nor affordable when T. dimidiata is widely distributed at low infestation levels. Further challenges involve research on T. dimidiata reinfestation, diversification of vector control strategies, and implementation of sustainable vector surveillance. © The American Society of Tropical Medicine and Hygiene.

EFFECTS OF SHORT-TERM USE OF XYLITOL CHEWING GUM AND MOLTITOL ORAL SPRAY ON SALIVARY STREPTOCOCCUS MUTANS AND ORAL PLAQUE.

PubMed

Mitrakul, Kemthong; Srisatjaluk, Ratchapin; Vongsawan, Kutkao; Teerawongpairoj, Chayanid; Choongphong, Nachata; Panich, Tathata; Kaewvimonrat, Pravee

2017-03-01

The purpose of this study was to investigate the short-term effects of xylitol chewing gum and maltitol spray on the concentration of salivary mutans streptococci (MS) and on the plaque index. Eighty-one second, third and fourth year dental and dental assistant students with a salivary MS concentration > 103 CFU/ml cultured on mitis salivarius bacitracin (MSB) agar were included in the study. The age range of subjects was 18-23 years. The participants were divided into 3 groups: control, xylitol chewing gum and maltitol spray groups. Each subject brushed their teeth with fluoridated toothpaste (1,000 ppm). Each subject in the xylitol chewing gum group was told to chew 2 pieces, 6 times a day (total xylitol dose=7.3 g/day) for 4 weeks. Each subject in the maltitol spray group was told to spray one puff twice daily (morning and evening) for 4 weeks. A dental examination and saliva samples to determine the salivary MS concentration were collected at baseline and at 2 and 4 weeks after experiment initiation. The nonparametric Mann–Whitney U test was used to analyze differences among groups. The mean ages in the control, xylitol chewing gum and maltitol spray groups were 22±1, 20±1 and 20±1 years, respectively. The mean MS concentrations at the beginning of the study and after 2 weeks in the control, and xylitol chewing gum and moltitol oral spray groups were not significantly different from each other. There was a significantly lower MS concentration in the moltitol oral spray group than in the control group by 4 weeks (p=0.045) but no significant difference between the control group and the xylitol gum group by 4 weeks. There were no significant differences in the mean plaque index at baseline among the control group, the xylitol chewing gum group and the moltitol oral spray group. The plaque index was significantly lower in the xylitol chewing gum group than the control group (p=0.003) at 2 weeks but not 4 weeks. There was no significant difference in the mean plaque index between the control group and the moltitol oral spray group at any time. Using the maltitol spray significantly reduced the MS level in the saliva by 4 weeks use but using the xylitol gum did not. However, using the xylitol chewing gum did reduce the mean plaque by 2 weeks use but the effect did not last; by 4 weeks there was no difference from control. The moltitol spray provided no benefit over the control in reducing the mean plaque index.

Some Factors Affecting the Reproducibility of Penetration and the Cut-Off of Oil Sprays for Fuel-injection Engines

NASA Technical Reports Server (NTRS)

Beardsley, E G

1928-01-01

This investigation was undertaken at the Langley Memorial Aeronautical Laboratory in connection with a general research on fuel-injection for aircraft. The purpose of the investigation was to determine the factors controlling the reproducibility of spray penetration and secondary discharges after cut-off. The development of single sprays from automatic injection valves was recorded by means of special high-speed photographic apparatus capable of taking 25 consecutive pictures of the moving spray at a rate of 4,000 per second. The effect of two types of injection valves, injection-valve tube length, initial pressure in the injection-valve tube, speed of the injection control mechanism, and time of spray cut-off, on the reproducibility of spray penetration, and on secondary discharges were investigated. It was found that neither type of injection valve materially affected spray reproducibility. The initial pressure in the injection-valve tube controlled the reproducibility of spray penetrations. An increase in the initial pressure or in the length of the injection-valve tube slightly increased the spray penetration within the limits of this investigation. The speed of the injection-control mechanism did not affect the penetration. Analysis of the results indicates that secondary discharges were caused in this apparatus by pressure waves initiated by the rapid opening of the cut-off valve. The secondary discharges were eliminated in this investigation by increasing the length of the injection-valve tube. (author)

Method and apparatus for heat extraction by controlled spray cooling

DOEpatents

Edwards, Christopher Francis; Meeks, Ellen; Kee, Robert; McCarty, Kevin

1999-01-01

Two solutions to the problem of cooling a high temperature, high heat flux surface using controlled spray cooling are presented for use on a mandrel. In the first embodiment, spray cooling is used to provide a varying isothermal boundary layer on the side portions of a mandrel by providing that the spray can be moved axially along the mandrel. In the second embodiment, a spray of coolant is directed to the lower temperature surface of the mandrel. By taking advantage of super-Leidenfrost cooling, the temperature of the high temperature surface of the mandrel can be controlled by varying the mass flux rate of coolant droplets. The invention has particular applicability to the field of diamond synthesis using chemical vapor deposition techniques.

A Modified Experimental Hut Design for Studying Responses of Disease-Transmitting Mosquitoes to Indoor Interventions: The Ifakara Experimental Huts

PubMed Central

Okumu, Fredros O.; Moore, Jason; Mbeyela, Edgar; Sherlock, Mark; Sangusangu, Robert; Ligamba, Godfrey; Russell, Tanya; Moore, Sarah J.

2012-01-01

Differences between individual human houses can confound results of studies aimed at evaluating indoor vector control interventions such as insecticide treated nets (ITNs) and indoor residual insecticide spraying (IRS). Specially designed and standardised experimental huts have historically provided a solution to this challenge, with an added advantage that they can be fitted with special interception traps to sample entering or exiting mosquitoes. However, many of these experimental hut designs have a number of limitations, for example: 1) inability to sample mosquitoes on all sides of huts, 2) increased likelihood of live mosquitoes flying out of the huts, leaving mainly dead ones, 3) difficulties of cleaning the huts when a new insecticide is to be tested, and 4) the generally small size of the experimental huts, which can misrepresent actual local house sizes or airflow dynamics in the local houses. Here, we describe a modified experimental hut design - The Ifakara Experimental Huts- and explain how these huts can be used to more realistically monitor behavioural and physiological responses of wild, free-flying disease-transmitting mosquitoes, including the African malaria vectors of the species complexes Anopheles gambiae and Anopheles funestus, to indoor vector control-technologies including ITNs and IRS. Important characteristics of the Ifakara experimental huts include: 1) interception traps fitted onto eave spaces and windows, 2) use of eave baffles (panels that direct mosquito movement) to control exit of live mosquitoes through the eave spaces, 3) use of replaceable wall panels and ceilings, which allow safe insecticide disposal and reuse of the huts to test different insecticides in successive periods, 4) the kit format of the huts allowing portability and 5) an improved suite of entomological procedures to maximise data quality. PMID:22347415

Malathion aerial spray controls the pine needle -sheath miner

Treesearch

Robert E. Stevens

1966-01-01

A water emulsion malathion spray, applied by helicopter at the rate of 1 lb. of insecticide in 25 gallons of water, effectively controlled the pine needle-sheath miner (Zelleria haimbachi Busck). Numbers of insects in the sprayed area were reduced by 98.6 percent 24 hours after treatment.

Fungicide spray coverage from ground-based sprayers in mature pecan trees

USDA-ARS?s Scientific Manuscript database

Air-blast sprayers are widely used to control pecan scab (Fusicladium effusum) on pecan trees. Good spray coverage is critical to ensure disease control and to minimize risk of fungicide resistance. Spray coverage from an air-blast sprayer, typical of the sprayer used by commercial producers, was me...

Aerial electrostatic spray deposition and canopy penetration in cotton

USDA-ARS?s Scientific Manuscript database

Spray deposition on abaxial and adaxial leaf surfaces along with canopy penetration are essential for insect control and foliage defoliation in cotton production agriculture. Researchers have reported that electrostatically charged sprays have increased spray deposit onto these surfaces under widel...

Reduced-risk management of Rhagoletis cerasi flies (host race Prunus) in combination with a preliminary phenological model.

PubMed

Kovanci, O B; Kovanci, B

2006-01-01

Seasonal flight activity of Rhagoletis cerasi (L.) (Diptera: Tephritidae) adults was monitored using yellow sticky traps at sweet cherry orchards under different management regimes in Bursa, northwestern Turkey, during 1997-1998. In the reduced-risk backyard orchards, soil ploughing in the fall or spring to destroy the pupae was combined with a single application of an insecticide, while conventionally managed orchards received six to seven insecticide applications for controlling adults. Traps in commercial orchards caught significantly fewer adults than those in reduced-risk backyard orchards. Levels of cherry fruit fly fruit damage were very low (0.1%) in commercial orchards, whereas infestation rates averaged 2.2% in reduced-risk orchards. A preliminary phenology model was developed for optimal timing of insecticide applications based on air temperature summations since 1 February. In the reduced-risk backyard orchards, the first flies were captured between 25 May and 2 June, corresponding to an average degree-day (DD) accumulation of 582.50 +/- 10.50 DD at an altitude of 150 m. However, first adult emergence at 1170 m was recorded between 6 and 14 June, averaging 667.50 +/- 14.50 DD. Adult emergence exhibited bimodal peaks in a single flight at low altitude but there was a single peak at high altitude sites. Total adult flight period averaged 459 +/- 29.50 and 649 +/- 25.50 DD at low and high altitude sites, respectively. Our prediction model suggests that the optimum spray-window for a single insecticide application occurs between 577.70 and 639.40 DD at 150 m and between 780.90 and 848.60 DD at 1170 m.

Reduced-Risk Management of Rhagoletis cerasi Flies (Host Race Prunus) in Combination with a Preliminary Phenological Model

PubMed Central

Kovanci, O. B.; Kovanci, B.

2006-01-01

Seasonal flight activity of Rhagoletis cerasi (L.) (Diptera: Tephritidae) adults was monitored using yellow sticky traps at sweet cherry orchards under different management regimes in Bursa, northwestern Turkey, during 1997–1998. In the reduced-risk backyard orchards, soil ploughing in the fall or spring to destroy the pupae was combined with a single application of an insecticide, while conventionally managed orchards received six to seven insecticide applications for controlling adults. Traps in commercial orchards caught significantly fewer adults than those in reduced-risk backyard orchards. Levels of cherry fruit fly fruit damage were very low (0.1%) in commercial orchards, whereas infestation rates averaged 2.2% in reduced-risk orchards. A preliminary phenology model was developed for optimal timing of insecticide applications based on air temperature summations since 1 February. In the reduced-risk backyard orchards, the first flies were captured between 25 May and 2 June, corresponding to an average degree-day (DD) accumulation of 582.50 ± 10.50 DD at an altitude of 150 m. However, first adult emergence at 1170 m was recorded between 6 and 14 June, averaging 667.50 ± 14.50 DD. Adult emergence exhibited bimodal peaks in a single flight at low altitude but there was a single peak at high altitude sites. Total adult flight period averaged 459 ± 29.50 and 649 ± 25.50 DD at low and high altitude sites, respectively. Our prediction model suggests that the optimum spray-window for a single insecticide application occurs between 577.70 and 639.40 DD at 150 m and between 780.90 and 848.60 DD at 1170 m. PMID:20298111

The Sequential Aerosol Technique: A Major Component in an Integrated Strategy of Intervention against Riverine Tsetse in Ghana

PubMed Central

Adam, Yahaya; Cecchi, Giuliano; Kgori, Patrick M.; Marcotty, Tanguy; Mahama, Charles I.; Abavana, Martin; Anderson, Benita; Paone, Massimo; Mattioli, Raffaele; Bouyer, Jérémy

2013-01-01

Background An integrated strategy of intervention against tsetse flies was implemented in the Upper West Region of Ghana (9.62°–11.00° N, 1.40°–2.76° W), covering an area of ≈18,000 km2 within the framework of the Pan-African Tsetse and Trypanosomosis Eradication Campaign. Two species were targeted: Glossina tachinoides and Glossina palpalis gambiensis. Methodology/Principal Findings The objectives were to test the potentiality of the sequential aerosol technique (SAT) to eliminate riverine tsetse species in a challenging subsection (dense tree canopy and high tsetse densities) of the total sprayed area (6,745 km2) and the subsequent efficacy of an integrated strategy including ground spraying (≈100 km2), insecticide treated targets (20,000) and insecticide treated cattle (45,000) in sustaining the results of tsetse suppression in the whole intervention area. The aerial application of low-dosage deltamethrin aerosols (0.33–0.35 g a.i/ha) was conducted along the three main rivers using five custom designed fixed-wings Turbo thrush aircraft. The impact of SAT on tsetse densities was monitored using 30 biconical traps deployed from two weeks before until two weeks after the operations. Results of the SAT monitoring indicated an overall reduction rate of 98% (from a pre-intervention mean apparent density per trap per day (ADT) of 16.7 to 0.3 at the end of the fourth and last cycle). One year after the SAT operations, a second survey using 200 biconical traps set in 20 sites during 3 weeks was conducted throughout the intervention area to measure the impact of the integrated control strategy. Both target species were still detected, albeit at very low densities (ADT of 0.27 inside sprayed blocks and 0.10 outside sprayed blocks). Conclusions/Significance The SAT operations failed to achieve elimination in the monitored section, but the subsequent integrated strategy maintained high levels of suppression throughout the intervention area, which will contribute to improving animal health, increasing animal production and fostering food security. PMID:23516662

Using Bayleton (Triadimefon) to Control Fusiform Rust in Pine Tree Nurseries

Treesearch

G.A. Snow; S.J. Rowan; J.P. Jones; W. D. Kelley; J.G. Mexal

1979-01-01

Bayletor® was field-tested for fusiform rust control at eight pine tree nurseries during the spring of 1978. Four to six foliar sprays of this systemic fungicide were as effective as ferbam sprayed 16 to 36 times. Seed treatment with Bayleton reduced infection levels but did not significantly improve rust control in plots sprayed with Bayleton. At high rates, Bayleton...

Assessment of Injuries Caused by Anastrepha fraterculus (Wied.) (Diptera: Tephritidae) on the Incidence of Bunch Rot Diseases in Table Grape.

PubMed

Machota, R; Bortoli, L C; Cavalcanti, F R; Botton, M; Grützmacher, A D

2016-08-01

Anastrepha fraterculus (Wied.) is the main insect pest of table grapes (Vitis vinifera) in the Southern Region of Brazil. In this study, we aimed to investigate the effect of fruit puncturing by adult females and larval infestation by A. fraterculus on the occurrence of bunch rot disease in the grape (cultivar "Itália") by evaluating grapes (a) punctured for oviposition by females of A. fraterculus, sterilized in laboratory with novaluron (40 mg L(-1)) and further spray-inoculated separately with Botrytis cinerea (1 × 10(6) conidia mL(-1)), Glomerella cingulata (1 × 10(6) conidia mL(-1)), and bacteria and yeast that cause sour rot (1 × 10(5) cells mL(-1)), (b) grapes punctured for oviposition by non-sterilized females with pathogen spraying, (c) grapes with mechanical wounds and pathogen spraying, (d) grapes with no wounds and with pathogen spraying, (e) grapes punctured for oviposition by A. fraterculus chemically sterilized in laboratory with novaluron, (f) grapes punctured for oviposition by A. fraterculus non-sterilized in laboratory with novaluron, (g) grapes with mechanical wounds, and (h) grapes with no sterilization or pathogen spraying. Our data indicated that the mechanical and oviposition wounds caused by A. fraterculus increased the percentage of grapes infected by B. cinerea, G. cingulata, and microorganisms of acid rot. The grape puncturing by A. fraterculus and the mechanical wound allows the penetration of B. cinerea and microorganisms leading to acid rot. We conclude that the fruit fly A. fraterculus may facilitate phytopathogens penetration leading to bunch rots in the table grape Itália.

The spray-drying process is sufficient to inactivate infectious porcine epidemic diarrhea virus in plasma.

PubMed

Gerber, Priscilla F; Xiao, Chao-Ting; Chen, Qi; Zhang, Jianqiang; Halbur, Patrick G; Opriessnig, Tanja

2014-11-07

Porcine epidemic diarrhea virus (PEDV) is considered an emergent pathogen associated with high economic losses in many pig rearing areas. Recently it has been suggested that PEDV could be transmitted to naïve pig populations through inclusion of spray-dried porcine plasma (SDPP) into the nursery diet which led to a ban of SDPP in several areas in North America and Europe. To determine the effect of spray-drying on PEDV infectivity, 3-week-old pigs were intragastrically inoculated with (1) raw porcine plasma spiked with PEDV (RAW-PEDV-CONTROL), (2) porcine plasma spiked with PEDV and then spray dried (SD-PEDV-CONTROL), (3) raw plasma from PEDV infected pigs (RAW-SICK), (4) spray-dried plasma from PEDV infected pigs (SD-SICK), or (5) spray-dried plasma from PEDV negative pigs (SD-NEG-CONTROL). For the spray-drying process, a tabletop spray-dryer with industry-like settings for inlet and outlet temperatures was used. In the RAW-PEDV-CONTROL group, PEDV RNA was present in feces at day post infection (dpi) 3 and the pigs seroconverted by dpi 14. In contrast, PEDV RNA in feces was not detected in any of the pigs in the other groups including the SD-PEDV-CONTROL group and none of the pigs had seroconverted by termination of the project at dpi 28. This work provides direct evidence that the experimental spray-drying process used in this study was effective in inactivating infectious PEDV in the plasma. Additionally, plasma collected from PEDV infected pigs at peak disease did not contain infectious PEDV. These findings suggest that the risk for PEDV transmission through commercially produced SDPP is minimal. Copyright © 2014 Elsevier B.V. All rights reserved.

In-situ control system for atomization

DOEpatents

Anderson, I.E.; Figliola, R.S.; Terpstra, R.L.

1995-06-13

Melt atomizing apparatus comprising a melt supply orifice for supplying the melt for atomization and gas supply orifices proximate the melt supply orifice for supplying atomizing gas to atomize the melt as an atomization spray is disclosed. The apparatus includes a sensor, such as an optical and/or audio sensor, for providing atomization spray data, and a control unit responsive to the sensed atomization spray data for controlling at least one of the atomizing gas pressure and an actuator to adjust the relative position of the gas supply orifice and melt supply in a manner to achieve a desired atomization spray. 3 figs.

In-situ control system for atomization

DOEpatents

Anderson, Iver E.; Figliola, Richard S.; Terpstra, Robert L.

1995-06-13

Melt atomizing apparatus comprising a melt supply orifice for supplying the melt for atomization and gas supply orifices proximate the melt supply orifice for supplying atomizing gas to atomize the melt as an atomization spray. The apparatus includes a sensor, such as an optical and/or audio sensor, for providing atomization spray data, and a control unit responsive to the sensed atomization spray data for controlling at least one of the atomizing gas pressure and an actuator to adjust the relative position of the gas supply orifice and melt supply in a manner to achieve a desired atomization spray.

Desulfurization characteristics of rapidly hydrated sorbents with various adhesive carrier particles for a semidry CFB-FGD system.

PubMed

You, Changfu; Li, Yuan

2013-03-19

Semidry flue gas desulfurization (FGD) experiments were conducted using rapidly hydrated sorbents with four different adhesive carrier particles: circulation ash from a circulating fluidized bed boiler (CFBB circulation ash), fly ash from the first electrical field of the electrostatic precipitator of a circulating fluidized bed boiler (CFBB ESP ash), fly ash from a chain boiler (chain boiler ash), and river sand smaller than 1 mm. The influences of various adhesive carrier particles and operating conditions on the desulfurization characteristics of the sorbents were investigated, including sprayed water, reaction temperature, and the ratio of calcium to sulfur (Ca/S). The experimental results indicated that the rapidly hydrated sorbents had better desulfurization characteristics by using adhesive carrier particles which possessed better pore, adhesion, and fluidization characteristics. The desulfurization efficiency of the system increased as the reaction temperature decreased, it improved from 35% to 90% as the mass flow rate of the sprayed water increased from 0 to 10 kg/h, and it increased from 65.6% to 82.7% as Ca/S increased from 1.0 to 2.0. Based on these findings, a new semidry circulating fluidized bed (CFB)-FGD system using rapidly hydrated sorbent was developed. Using the rapidly hydrated sorbent, this system uses a cyclone separator instead of an ESP or a bag filter to recycle the sorbent particles, thereby decreasing the system flow resistance, saving investment and operating costs of the solids collection equipment.

Investigation of Spray Cooling Schemes for Dynamic Thermal Management

NASA Astrophysics Data System (ADS)

Yata, Vishnu Vardhan Reddy

This study aims to investigate variable flow and intermittent flow spray cooling characteristics for efficiency improvement in active two-phase thermal management systems. Variable flow spray cooling scheme requires control of pump input voltage (or speed), while intermittent flow spray cooling scheme requires control of solenoid valve duty cycle and frequency. Several testing scenarios representing dynamic heat load conditions are implemented to characterize the overall performance of variable flow and intermittent flow spray cooling cases in comparison with the reference, steady flow spray cooling case with constant flowrate, continuous spray cooling. Tests are conducted on a small-scale, closed loop spray cooling system featuring a pressure atomized spray nozzle. HFE-7100 dielectric liquid is selected as the working fluid. Two types of test samples are prepared on 10 mm x 10 mm x 2 mm copper substrates with matching size thick film resistors attached onto the opposite side, to generate heat and simulate high heat flux electronic devices. The test samples include: (i) plain, smooth surface, and (ii) microporous surface featuring 100 ?m thick copper-based coating prepared by dual stage electroplating technique. Experimental conditions involve HFE-7100 at atmospheric pressure and 30°C and 10°C subcooling. Steady flow spray cooling tests are conducted at flow rates of 2-5 ml/cm2.s, by controlling the heat flux in increasing steps, and recording the corresponding steady-state temperatures to obtain cooling curves in the form of surface superheat vs. heat flux. Variable flow and intermittent flow spray cooling tests are done at selected flowrate and subcooling conditions to investigate the effects of dynamic flow conditions on maintaining the target surface temperatures defined based on reference steady flow spray cooling performance.

Modifications Of A Commercial Spray Gun

NASA Technical Reports Server (NTRS)

Allen, Peter B.

1993-01-01

Commercial spray gun modified to increase spray rate and make sprayed coats more nearly uniform. Consists of gun head and pneumatic actuator. Actuator opens valves for two chemical components, called "A" and "B," that react to produce foam. Components flow through orifices, into mixing chamber in head. Mixture then flows through control orifice to spray tip. New spray tip tapered to reduce area available for accumulation of foam and makes tip easier to clean.

Within-band spray distribution of nozzles used for herbaceous plant control

Treesearch

James H. Miller

1994-01-01

Abstract. Described are the spray patterns of nozzles setup for banded herbaceous plant control treatments. Spraying Systems Company nozzles. were tested, but similar nozzles are available from other manufacturers. Desirable traits were considered to be as follows: an even distribution pattern, low volume, low height, large droplets, and a single...

14 CFR 25.239 - Spray characteristics, control, and stability on water.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Spray characteristics, control, and stability on water. 25.239 Section 25.239 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Flight Ground and Water Handling Characteristics § 25.239 Spray...

Controlling in situ crystallization of pharmaceutical particles within the spray dryer.

PubMed

Woo, Meng Wai; Lee, May Ginn; Shakiba, Soroush; Mansouri, Shahnaz

2017-11-01

Simultaneous solidification and in situ crystallization (or partial crystallization) of droplets within the drying chamber are commonly encountered in the spray drying of pharmaceuticals. The crystallinity developed will determine the functionality of the powder and its stability during storage. This review discusses strategies that can be used to control the in situ crystallization process. Areas covered: The premise of the strategies discussed focuses on the manipulation of the droplet drying rate relative to the timescale of crystallization. This can be undertaken by the control of the spray drying operation, by the use of volatile materials and by the inclusion of additives. Several predictive approaches for in situ crystallization control and new spray dryer configuration strategies are further discussed. Expert opinion: Most reports, hitherto, have focused on the crystallinity of the spray dried material or the development of crystallinity during storage. More mechanistic understanding of the in situ crystallization process during spray drying is required to guide product formulation trials. The key challenge will be in adapting the mechanistic approach to the myriad possible formulations in the pharmaceutical industry.

Relieving thermal discomfort: Effects of sprayed L-menthol on perception, performance, and time trial cycling in the heat.

PubMed

Barwood, M J; Corbett, J; Thomas, K; Twentyman, P

2015-06-01

L-menthol stimulates cutaneous thermoreceptors and induces cool sensations improving thermal comfort, but has been linked to heat storage responses; this could increase risk of heat illness during self-paced exercise in the heat. Therefore, L-menthol application could lead to a discrepancy between behavioral and autonomic thermoregulatory drivers. Eight male participants volunteered. They were familiarized and then completed two trials in hot conditions (33.5 °C, 33% relative humidity) where their t-shirt was sprayed with CONTROL-SPRAY or MENTHOL-SPRAY after 10 km (i.e., when they were hot and uncomfortable) of a 16.1-km cycling time trial (TT). Thermal perception [thermal sensation (TS) and comfort (TC)], thermal responses [rectal temperature (Trec ), skin temperature (Tskin )], perceived exertion (RPE), heart rate, pacing (power output), and TT completion time were measured. MENTHOL-SPRAY made participants feel cooler and more comfortable and resulted in lower RPE (i.e., less exertion) yet performance was unchanged [TT completion: CONTROL-SPRAY 32.4 (2.9) and MENTHOL-SPRAY 32.7 (3.0) min]. Trec rate of increase was 1.40 (0.60) and 1.45 (0.40) °C/h after CONTROL-SPRAY and MENTHOL-SPRAY application, which were not different. Spraying L-menthol toward the end of self-paced exercise in the heat improved perception, but did not alter performance and did not increase heat illness risk. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Sequential cryogen spraying for heat flux control at the skin surface

NASA Astrophysics Data System (ADS)

Majaron, Boris; Aguilar, Guillermo; Basinger, Brooke; Randeberg, Lise L.; Svaasand, Lars O.; Lavernia, Enrique J.; Nelson, J. Stuart

2001-05-01

Heat transfer rate at the skin-air interface is of critical importance for the benefits of cryogen spray cooling in combination with laser therapy of shallow subsurface skin lesions, such as port-wine stain birthmarks. With some cryogen spray devices, a layer of liquid cryogen builds up on the skin surface during the spurt, which may impair heat transfer across the skin surface due to relatively low thermal conductivity and potentially higher temperature of the liquid cryogen layer as compared to the spray droplets. While the mass flux of cryogen delivery can be adjusted by varying the atomizing nozzle geometry, this may strongly affect other spray properties, such as lateral spread (cone), droplet size, velocity, and temperature distribution. We present here first experiments with sequential cryogen spraying, which may enable accurate mass flux control through variation of spray duty cycle, while minimally affecting other spray characteristics. The observed increase of cooling rate and efficiency at moderate duty cycle levels supports the above described hypothesis of isolating liquid layer, and demonstrates a novel approach to optimization of cryogen spray devices for individual laser dermatological applications.

Obtaining Thickness-Limited Electrospray Deposition for 3D Coating.

PubMed

Lei, Lin; Kovacevich, Dylan A; Nitzsche, Michael P; Ryu, Jihyun; Al-Marzoki, Kutaiba; Rodriguez, Gabriela; Klein, Lisa C; Jitianu, Andrei; Singer, Jonathan P

2018-04-04

Electrospray processing utilizes the balance of electrostatic forces and surface tension within a charged spray to produce charged microdroplets with a narrow dispersion in size. In electrospray deposition, each droplet carries a small quantity of suspended material to a target substrate. Past electrospray deposition results fall into two major categories: (1) continuous spray of films onto conducting substrates and (2) spray of isolated droplets onto insulating substrates. A crossover regime, or a self-limited spray, has only been limitedly observed in the spray of insulating materials onto conductive substrates. In such sprays, a limiting thickness emerges, where the accumulation of charge repels further spray. In this study, we examined the parametric spray of several glassy polymers to both categorize past electrospray deposition results and uncover the critical parameters for thickness-limited sprays. The key parameters for determining the limiting thickness were (1) field strength and (2) spray temperature, related to (i) the necessary repulsive field and (ii) the ability for the deposited materials to swell in the carrier solvent vapor and redistribute charge. These control mechanisms can be applied to the uniform or controllably-varied microscale coating of complex three-dimensional objects.

Proceedings from the 2nd International Symposium on Formation Flying Missions and Technologies

NASA Technical Reports Server (NTRS)

2004-01-01

Topics discussed include: The Stellar Imager (SI) "Vision Mission"; First Formation Flying Demonstration Mission Including on Flight Nulling; Formation Flying X-ray Telescope in L2 Orbit; SPECS: The Kilometer-baseline Far-IR Interferometer in NASA's Space Science Roadmap Presentation; A Tight Formation for Along-track SAR Interferometry; Realization of the Solar Power Satellite using the Formation Flying Solar Reflector; SIMBOL-X : Formation Flying for High-Energy Astrophysics; High Precision Optical Metrology for DARWIN; Close Formation Flight of Micro-Satellites for SAR Interferometry; Station-Keeping Requirements for Astronomical Imaging with Constellations of Free-Flying Collectors; Closed-Loop Control of Formation Flying Satellites; Formation Control for the MAXIM Mission; Precision Formation Keeping at L2 Using the Autonomous Formation Flying Sensor; Robust Control of Multiple Spacecraft Formation Flying; Virtual Rigid Body (VRB) Satellite Formation Control: Stable Mode-Switching and Cross-Coupling; Electromagnetic Formation Flight (EMFF) System Design, Mission Capabilities, and Testbed Development; Navigation Algorithms for Formation Flying Missions; Use of Formation Flying Small Satellites Incorporating OISL's in a Tandem Cluster Mission; Semimajor Axis Estimation Strategies; Relative Attitude Determination of Earth Orbiting Formations Using GPS Receivers; Analysis of Formation Flying in Eccentric Orbits Using Linearized Equations of Relative Motion; Conservative Analytical Collision Probabilities for Orbital Formation Flying; Equations of Motion and Stability of Two Spacecraft in Formation at the Earth/Moon Triangular Libration Points; Formations Near the Libration Points: Design Strategies Using Natural and Non-Natural Ares; An Overview of the Formation and Attitude Control System for the Terrestrial Planet Finder Formation Flying Interferometer; GVE-Based Dynamics and Control for Formation Flying Spacecraft; GNC System Design for a New Concept of X-Ray Distributed Telescope; GNC System for the Deployment and Fine Control of the DARWIN Free-Flying Interferometer; Formation Algorithm and Simulation Testbed; and PLATFORM: A Formation Flying, RvD and Robotic Validation Test-bench.

Managing the horn fly (Diptera: Muscidae) using an electric walk-through fly trap.

PubMed

Watson, D W; Stringham, S M; Denning, S S; Washburn, S P; Poore, M H; Meier, A

2002-10-01

An electric walk-through fly trap was evaluated for the management of the horn fly, Hematobia irritans (L.), on dairy cattle in North Carolina over 2 yr. The trap relies on black lights and electrocution grids to attract and kill flies that are brushed from the cattle passing through. During the first season, horn fly densities were reduced from >1,400 to <200 flies per animal. Horn fly density averaged 269.2 +/- 25.8 on cattle using the walk-through fly trap twice daily, and 400.2 +/- 43.5 on the control group during the first year. The second year, seasonal mean horn fly density was 177.3 +/- 10.8 on cattle using the walk-through fly trap compared with 321.1 +/- 15.8 on the control group. No insecticides were used to control horn flies during this 2-yr study.

Real-Time Variable Rate Spraying in Orchards and Vineyards: A Review

NASA Astrophysics Data System (ADS)

Wandkar, Sachin Vilas; Bhatt, Yogesh Chandra; Jain, H. K.; Nalawade, Sachin M.; Pawar, Shashikant G.

2018-06-01

Effective and efficient use of pesticides in the orchards is of concern since many years. With the conventional constant rate sprayers, equal dose of pesticide is applied to each tree. Since, there is great variation in size and shape of each tree in the orchard, trees gets either oversprayed or undersprayed. Real-time variable rate spraying technology offers pesticide application in accordance with tree size. With the help of suitable sensors, tree characteristics such as canopy volume, foliage density, etc. can be acquired and with the micro-processing unit coupled with proper algorithm, flow of electronic proportional valves can be controlled thus, controlling the flow rate of nozzles according to tree characteristics. Also, sensors can help in the detection of spaces in-between trees which allows to control the spray in spaces. Variable rate spraying helps in achieving precision in spraying operation especially inside orchards. This paper reviews the real-time variable rate spraying technology and efforts made by the various researchers for real-time variable application in the orchards and vineyards.

Real-Time Variable Rate Spraying in Orchards and Vineyards: A Review

NASA Astrophysics Data System (ADS)

Wandkar, Sachin Vilas; Bhatt, Yogesh Chandra; Jain, H. K.; Nalawade, Sachin M.; Pawar, Shashikant G.

2018-02-01

Effective and efficient use of pesticides in the orchards is of concern since many years. With the conventional constant rate sprayers, equal dose of pesticide is applied to each tree. Since, there is great variation in size and shape of each tree in the orchard, trees gets either oversprayed or undersprayed. Real-time variable rate spraying technology offers pesticide application in accordance with tree size. With the help of suitable sensors, tree characteristics such as canopy volume, foliage density, etc. can be acquired and with the micro-processing unit coupled with proper algorithm, flow of electronic proportional valves can be controlled thus, controlling the flow rate of nozzles according to tree characteristics. Also, sensors can help in the detection of spaces in-between trees which allows to control the spray in spaces. Variable rate spraying helps in achieving precision in spraying operation especially inside orchards. This paper reviews the real-time variable rate spraying technology and efforts made by the various researchers for real-time variable application in the orchards and vineyards.

Improving the biocontrol potential of entomopathogenic nematodes against Mamestra brassicae: effect of spray application technique, adjuvants and an attractant.

PubMed

Beck, Bert; Brusselman, Eva; Nuyttens, David; Moens, Maurice; Temmerman, Femke; Pollet, Sabien; Van Weyenberg, Stephanie; Spanoghe, Pieter

2014-01-01

Steinernema carpocapsae Weiser, an entomopathogenic nematode (EPN), is a potential biological control agent for the cabbage moth (Mamestra brassicae L.). This research aimed to identify a suitable spray application technique, and to determine whether yeast extract added to an EPN spray has an attracting and/or a feeding stimulant effect on M. brassicae. The biological control capabilities of EPN against this pest were examined in the field. Good coverage of the underside of cauliflower leaves, the habitat of young instar larvae (L1-L4) of M. brassicae was obtained using different spray boom configurations with vertical extensions that carried underleaf spraying nozzles. One of the configurations was selected for field testing with an EPN spray. Brewer's yeast extract stimulated larval feeding on leaves, and increased the mortality of these larvae when exposed to EPN. The field trial showed that a spray application with S. carpocapsae, Addit and xanthan gum can effectively lower the numbers of cabbage heads damaged by M. brassicae. Brewer's yeast extract did not significantly increase this field performance of EPN. Steinernema carpocapsae, applied with an appropriate spray technique, can be used within biological control schemes as part of a resistance management programme for Bt. © 2013 Society of Chemical Industry.

Further Evaluation of Spray Characterization of Sprayers Typically Used in Vector Control

DTIC Science & Technology

2012-01-01

E1260. Standard test method for determining liquid drop size characteristics in a spray using optical nonimaging light-scattering instru- ments...The time that the spray cloud was directed through the optical path of the laser varied between sprayers depending on the width of the spray plume

Herbicidal drift control: aerial spray equipment, formulations, and supervision.

Treesearch

H. Gratkowski

1974-01-01

Public concern over environmental pollution requires increasingly sophisticated procedures when herbicides are used in silviculture. Many specialized aerial application systems and spray additives have been developed to reduce drift of herbicidal sprays. This publication provides forest-land managers with a brief description of these aerial spray systems and additives...

Biological control of livestock pests : Parasitoids

USDA-ARS?s Scientific Manuscript database

House flies, Musca domestica L., and stable flies, Stomoxys calcitrans (L.), are common pests on livestock, poultry, and equine facilities. Biological control of filth flies with pupal parasitoids can be used in conjunction with other control methods as part of an integrated fly management program. ...

A water-cannon salute from two Air Force fire trucks heralds NASA research pilot Gordon Fullerton's final mission as his NASA F/A-18 taxis beneath the spray.

NASA Image and Video Library

2007-12-21

Long-time NASA Dryden research pilot and former astronaut C. Gordon Fullerton capped an almost 50-year flying career, including more than 38 years with NASA, with a final flight in a NASA F/A-18 on Dec. 21, 2007. Fullerton and Dryden research pilot Jim Smolka flew a 90-minute pilot proficiency formation aerobatics flight with another Dryden F/A-18 and a Dryden T-38 before concluding with two low-level formation flyovers of Dryden before landing. Fullerton was honored with a water-cannon spray arch provided by two fire trucks from the Edwards Air Force Base fire department as he taxied the F/A-18 up to the Dryden ramp, and was then greeted by his wife Marie and several hundred Dryden staff after his final flight. Fullerton began his flying career with the U.S. Air Force in 1958 after earning bachelor's and master's degrees in mechanical engineering from the California Institute of Technology. Initially trained as a fighter pilot, he later transitioned to multi-engine bombers and became a bomber operations test pilot after attending the Air Force Aerospace Research Pilot School at Edwards Air Force Base, Calif. He then was assigned to the flight crew for the planned Air Force Manned Orbital Laboratory in 1966. Upon cancellation of that program, the Air Force assigned Fullerton to NASA's astronaut corps in 1969. He served on the support crews for the Apollo 14, 15, 16 and 17 lunar missions, and was later assigned to one of the two flight crews that piloted the space shuttle prototype Enterprise during the Approach and Landing Test program at Dryden. He then logged some 382 hours in space when he flew on two early space shuttle missions, STS-3 on Columbia in 1982 and STS-51F on Challenger in 1985. He joined the flight crew branch at NASA Dryden after leaving the astronaut corps in 1986. During his 21 years at Dryden, Fullerton was project pilot on a number of high-profile research efforts, including the Propulsion Controlled Aircraft, the high-speed landing tests of

Process-based quality for thermal spray via feedback control

NASA Astrophysics Data System (ADS)

Dykhuizen, R. C.; Neiser, R. A.

2006-09-01

Quality control of a thermal spray system manufacturing process is difficult due to the many input variables that need to be controlled. Great care must be taken to ensure that the process remains constant to obtain a consistent quality of the parts. Control is greatly complicated by the fact that measurement of particle velocities and temperatures is a noisy stochastic process. This article illustrates the application of quality control concepts to a wire flame spray process. A central feature of the real-time control system is an automatic feedback control scheme that provides fine adjustments to ensure that uncontrolled variations are accommodated. It is shown how the control vectors can be constructed from simple process maps to independently control particle velocity and temperature. This control scheme is shown to perform well in a real production environment. We also demonstrate that slight variations in the feed wire curvature can greatly influence the process. Finally, the geometry of the spray system and sensor must remain constant for the best reproducibility.

An experimental study of the atmospheric boundary layer modified by a change in surface roughness and surface temperature

NASA Technical Reports Server (NTRS)

Tieleman, H. W.; Derrington, D. B., Jr.

1977-01-01

Turbulent flow, resembling an on-shore flow from the ocean crossing the beach at an oblique angle, is investigated. Measurements of this flow have been taken at high sample rates and include measurements at various heights, high enough to describe the portion of the mean wind and temperature profiles and fluxes that are of interest for the solution of practical engineering problems. These problems could include air pollution (fumigation and plume trapping), operation of low flying aircraft, crop-spraying and crop-dusting operations.

A hypothesis of the Effect of a New Nasal Spray Made from Natural Medicines on Allergic Rhinitis in Animals

NASA Astrophysics Data System (ADS)

Zhai, Hailong; Wang, Yufang

2018-01-01

To verify the effect of a new nasal spray made from natural medicines on allergic rhinitis in animals. Methods: The main natural medicines contained in Acusine nasal spray plus essential traditional Chinese medicine contained in drugs for allergic rhinitis in Chinese market were used. By preparation process of extraction of traditional Chinese medicine such as steam distillation, ethanol extraction, a new nasal spray made from natural medicines was prepared. In the meantime, 24 BALB/c mice and New Zealand white rabbits were used. Then, mice were randomly divided into four group; control group, beclomethasone dipropionate group, Acusine group and new spray group, 6 mice in each group. Moreover, the effect of the new nasal spray made on passive cutaneous anaphylaxis was conducted by detecting absorptions of Evan’s blue (620nm) in the four groups. Allergic rhinitis models in 40 New Zealand white rabbits were established. Consequently, 40 allergic rhinitis models in rabbits were randomly divided into control group, Acusine group and new spray group, 10 rabbits in each group. The four groups were sprayed nasally with saline, Acusine spray and new spray respectively, three times/d, for 30 days. The nasal resistances in the four groups were measured with a rhinoresistometer. Moreover, their nasal mucosa was taken for HE staining. Consequently, their pathological manifestations were observed. The results: Absorption of Evan’s blue (620nm) of new spray group will be found significantly lower than Acusine group (P<0.05) and will have no significantly difference compared with beclomethasone dipropionate group(P>0.05). On the other hand, absorption of Evan’s blue (620nm) of beclomethasone dipropionate group will be significantly lower than Acusine group (P<0.05). Moreover, The nasal resistances of new spray group will be significantly lower than Acusine group (P<0.05) and will have no significantly difference compared with beclomethasone dipropionate group (P».05). Moreover, the nasal resistances of beclomethasone dipropionate group will be significantly lower than Acusine group (P<0.05). While, the nasal mucosa of control group will be found typical as nasal mucosa of allergic rhinitis. However, the nasal mucosa of beclomethasone dipropionate group, Acusine group and new spray group will be better than control group. Of them, new spray group will be the best. The nasal mucosa of beclomethasone dipropionate group will show the manifestation of drug-induced rhinitis. The conclusion: The invented new spray will not only have a better treatment effect on allergic rhinitis, similar with beclomethasone dipropionate, than Acusine Nasal Spray but also will not leave side effect on nasal mucosa, compared with beclomethasone dipropionate. Thus, the new spray made from natural medicines can be further studied as a better prescription drug, rather than an OTC like Acusine Nasal Spray, to replace beclomethasone dipropionate nasal spray. However, further study that would be required to produce a more meaningful answer.

Efficacy of Aedes aegypti control by indoor Ultra Low Volume (ULV) insecticide spraying in Iquitos, Peru

PubMed Central

Okamoto, Kenichi W.; Astete, Helvio; Vasquez, Gissella M.; Del Aguila, Clara; Pinedo, Raul; Cardenas, Roldan; Pacheco, Carlos; Chalco, Enrique; Rodriguez-Ferruci, Hugo; Scott, Thomas W.; Lloyd, Alun L.; Gould, Fred

2018-01-01

Background Aedes aegypti is a primary vector of dengue, chikungunya, Zika, and urban yellow fever viruses. Indoor, ultra low volume (ULV) space spraying with pyrethroid insecticides is the main approach used for Ae. aegypti emergency control in many countries. Given the widespread use of this method, the lack of large-scale experiments or detailed evaluations of municipal spray programs is problematic. Methodology/Principal findings Two experimental evaluations of non-residual, indoor ULV pyrethroid spraying were conducted in Iquitos, Peru. In each, a central sprayed sector was surrounded by an unsprayed buffer sector. In 2013, spray and buffer sectors included 398 and 765 houses, respectively. Spraying reduced the mean number of adults captured per house by ~83 percent relative to the pre-spray baseline survey. In the 2014 experiment, sprayed and buffer sectors included 1,117 and 1,049 houses, respectively. Here, the sprayed sector’s number of adults per house was reduced ~64 percent relative to baseline. Parity surveys in the sprayed sector during the 2014 spray period indicated an increase in the proportion of very young females. We also evaluated impacts of a 2014 citywide spray program by the local Ministry of Health, which reduced adult populations by ~60 percent. In all cases, adult densities returned to near-baseline levels within one month. Conclusions/Significance Our results demonstrate that densities of adult Ae. aegypti can be reduced by experimental and municipal spraying programs. The finding that adult densities return to approximately pre-spray densities in less than a month is similar to results from previous, smaller scale experiments. Our results demonstrate that ULV spraying is best viewed as having a short-term entomological effect. The epidemiological impact of ULV spraying will need evaluation in future trials that measure capacity of insecticide spraying to reduce human infection or disease. PMID:29624581

Efficacy of indigenous entomopathogenic nematodes (Rhabditida: Heterorhabditidae, Steinernematidae), from Rio Grande do Sul Brazil, against Anastrephafraterculus (Wied.) (Diptera: Tephritidae) in peach orchards.

PubMed

Barbosa-Negrisoli, Carla R C; Garcia, Mauro S; Dolinski, Claudia; Negrisoli, Aldomario S; Bernardi, Daniel; Nava, Dori Edson

2009-09-01

Laboratory, greenhouse, and field experiments were performed with the objective of selecting efficient indigenous strains of entomopathogenic nematodes (EPNs) from Rio Grande do Sul (RS) state, Brazil, for controlling the South American fruit fly, Anastrepha fraterculus (Wied.). Laboratory experiments were conducted in 24 well-plates filled with sterile sand and one insect per well. In greenhouse experiments, plastic trays filled with soil collected from the field were used, while in field experiments, holes were made in soil under the edge of peach tree canopies. Among 19 EPN strains tested, Heterorhabditis bacteriophora Poinar RS88 and Steinernema riobrave Cabanillas, Poinar, & Raulston RS59 resulted in higher A. fraterculus larval (pre-pupal) and pupal mortality, with LD(90) of 1630, 457 and 2851, 423 infective juveniles (IJs)/cm(2), respectively. Greenhouse experiments showed no differences in pupal mortality at 250 and 500IJs/cm(2) of either nematode. In the field, H. bacteriophora RS88 and S. riobravae RS59 sprayed individually over natural and artificially infested fruit (250IJs/cm(2)) resulted in A. fraterculus larval mortality of 51.3%, 28.1% and 20%, 24.3%, respectively. There was no significant difference in A. fraterculus pupal mortality sprayed with an aqueous suspension of either nematode; however, when using infected insect cadavers, H. bacteriophora RS88 was more efficient than S. riobrave RS59. Our results showed that H. bacteriophora RS88 was more virulent to insect larvae, with an efficient host search inside the infested fruit and control of pupae in the soil after being applied by aqueous suspension or infected cadavers.

The influence of additives and drying methods on quality attributes of fish protein powder made from saithe (Pollachius virens).

PubMed

Shaviklo, Gholam Reza; Thorkelsson, Gudjon; Arason, Sigurjon; Kristinsson, Hordur G; Sveinsdottir, Kolbrun

2010-09-01

Fish protein powder (FPP) is used in the food industry for developing formulated food products. This study investigates the feasibility of increasing the value of saithe (Pollachius virens) by producing a functional FPP. Quality attributes of spray and freeze-dried saithe surimi containing lyoprotectants were studied. A freeze-dried saithe surimi without lyoprotectants was also prepared as a control sample. The amount of protein, moisture, fat and carbohydrate in the FPPs were 745-928, 39-58, 21-32 and 10-151 g kg(-1). Quality attributes of FPPs were influenced by the two drying methods and lyoprotectants. The highest level of lipid oxidation was found in the control and the second highest in the spray-dried FPP. The spray-dried fish protein had the lowest viscosity among all FPPs. Gel-forming ability of samples with lyoprotectants was higher than that of the control. Water-binding capacity, emulsion properties and solubility of the freeze-dried fish protein containing lyoprotectants were significantly higher than spray-dried and control samples. However, functional properties of spray-dried FPP were higher than the control sample. It is feasible to develop value-added FPP from saithe surimi using spray- and freeze-drying processes, but freeze-dried FPP containing lyoprotectant had superior functional properties and stability compared with spray-dried sample. Both products might be used as functional protein ingredients in various food systems. Copyright 2010 Society of Chemical Industry.

Multiple-Nozzle Spray Head Applies Foam Insulation

NASA Technical Reports Server (NTRS)

Walls, Joe T.

1993-01-01

Spray head equipped with four-nozzle turret mixes two reactive components of polyurethane and polyisocyanurate foam insulating material and sprays reacting mixture onto surface to be insulated. If nozzle in use becomes clogged, fresh one automatically rotated into position, with minimal interruption of spraying process. Incorporates features recirculating and controlling pressures of reactive components to maintain quality of foam by ensuring proper blend at outset. Also used to spray protective coats on or in ships, aircraft, and pipelines. Sprays such reactive adhesives as epoxy/polyurethane mixtures. Components of spray contain solid-particle fillers for strength, fire retardance, toughness, resistance to abrasion, or radar absorption.

Hydraulic Spray Applications of Insecticides for the Control of Slash Pine Cone and Seed Insects

Treesearch

Edward P. Merkel

1964-01-01

Field spray tests were conducted from 1959 to 1961 in north Florida to evaluate the effectiveness of hydraulic spray applications of BHC, Guthion, and DDT for the control of coneworms, Dioryctria spp., and the slash pine seedworm, Laspeyresia anaranjada. Slash pines up to 40 feet in total height were protected from coneworm attack...

Aerial electrostatic-charged spray for deposition and efficacy against sweetpotato whitefly (Bemisia tabaci) on cotton

USDA-ARS?s Scientific Manuscript database

Efficacy of aerial electrostatic-charged sprays was evaluated for spray deposit characteristics and season-long control of sweet potato whitefly (SWF), Bemisia tabaci biotype B (a.k.a. B. argentifolii), in an irrigated 24-ha cotton field. Treatments included electrostatic-charged sprays at full and ...

mSpray: a mobile phone technology to improve malaria control efforts and monitor human exposure to malaria control pesticides in Limpopo, South Africa

PubMed Central

Eskenazi, Brenda; Quirós-Alcalá, Lesliam; Lipsitt, Jonah M.; Wu, Lemuel D.; Kruger, Philip; Ntimbane, Tzundzukani; Nawn, John Burns; Bornman, M. S. Riana; Seto, Edmund

2015-01-01

Recent estimates indicate that malaria has led to over half a million deaths worldwide, mostly to African children. Indoor residual spraying (IRS) of insecticides is one of the primary vector control interventions. However, current reporting systems do not obtain precise location of IRS events in relation to malaria cases, which poses challenges for effective and efficient malaria control. This information is also critical to avoid unnecessary human exposure to IRS insecticides. We developed and piloted a mobile-based application (mSpray) to collect comprehensive information on IRS spray events. We assessed the utility, acceptability and feasibility of using mSpray to gather improved homestead- and chemical-level IRS coverage data. We installed mSpray on 10 cell phones with data bundles, and pilot tested it with 13 users in Limpopo, South Africa. Users completed basic information (number of rooms/shelters sprayed; chemical used, etc.) on spray events. Upon submission, this information as well as geographic positioning system coordinates and time/date stamp were uploaded to a Google Drive Spreadsheet to be viewed in real time. We administered questionnaires, conducted focus groups, and interviewed key informants to evaluate the utility of the app. The low-cost, cell phone-based “mSpray” app was learned quickly by users, well accepted and preferred to the current paper-based method. We recorded 2,865 entries (99.1% had a GPS accuracy of 20 m or less) and identified areas of improvement including increased battery life. We also identified a number of logistic and user problems (e.g., cost of cell phones and cellular bundles, battery life, obtaining accurate GPS measures, user errors, etc.) that would need to be overcome before full deployment. Use of cell phone technology could increase the efficiency of IRS malaria control efforts by mapping spray events in relation to malaria cases, resulting in more judicious use of chemicals that are potentially harmful to humans and the environment. PMID:24769412

Spray combustion at normal and reduced gravity in counterflow and co-flow configurations

NASA Technical Reports Server (NTRS)

Gomez, Alessandro; Chen, Gung

1995-01-01

Liquid fuel dispersion in practical systems is typically achieved by spraying the fuel into a polydisperse distribution of droplets evaporating and burning in a turbulent gaseous environment In view of the nearly insurmountable difficulties of this two-phase flow, a systematic study of spray evaporation and burning in configurations of gradually increasing levels of complexity, starting from laminar sprays to fully turbulent ones, would be useful. A few years ago we proposed to use an electrostatic spray of charged droplets for this type of combustion experiments under well-defined conditions. In the simplest configuration, a liquid is fed into a small metal tube maintained at several kilovolts relative to a ground electrode few centimeters away. Under the action of the electric field, the liquid meniscus at the outlet of the capillary takes a conical shape, with a thin jet emerging from the cone tip (cone-jet mode). This jet breaks up farther downstream into a spray of charged droplets - the so-called ElectroSpray (ES). Several advantages distinguish the electrospray from alternative atomization techniques: (1) it can produce quasi-monodisperse droplets over a phenomenal size range; (2) the atomization, that is strictly electrostatic, is decoupled from gas flow processes, which provides some flexibility in the selection and control of the experimental conditions; (3) the Coulombic repulsion of homopolarly charged droplets induces spray self-dispersion and prevents droplet coalescence; (4) the ES provides the opportunity of studying regimes of slip between droplets and host gas without compromising the control of the spray properties; and (5) the compactness and potential controllability of this spray generation system makes it appealing for studies in reduced-gravity environments aimed at isolating the spray behavior from natural convection complications. With these premises, in March 1991 we initiated a series of experiments under NASA sponsorship (NAG3-1259 and 1688) in which the ES was used as a research tool to examine spray combustion in counter-flow and co-flow spray diffusion flames, as summarized below. The ultimate objective of this investigation is to examine the formation and burning of sprays of liquid fuels, at both normal and reduced gravity, first in laminar regimes and then in turbulent ones.

Influence of handpiece maintenance sprays on resin bonding to dentin.

PubMed

Sugawara, Toyotarou; Kameyama, Atsushi; Haruyama, Akiko; Oishi, Takumi; Kukidome, Nobuyuki; Takase, Yasuaki; Tsunoda, Masatake

2010-01-01

To investigate the influence of maintenance spray on resin bonding to dentin. The crown of extracted, caries-free human molars was transversally sectioned with a model trimmer to prepare the dentin surfaces from mid-coronal sound dentin, and then uniformly abraded with #600 silicon carbide paper. The dentin surfaces were randomly divided into three groups: oil-free spray group where maintenance cleaner for air bearing handpieces was sprayed onto the dentin surface for 1 s and rinsed with water spray for 30 s; oil-containing spray group where maintenance cleaner for micro motor handpieces was sprayed onto the dentin surface for 1 s and rinsed with water spray for 30 s; and control group where the surface was rinsed with water spray for 30 s and then air-dried. These surfaces were then bonded with Clearfil SE Bond (Kuraray Medical), and resin composite (Clearfil AP-X, Kuraray Medical) build-up crowns were incrementally constructed on the bonded surfaces. After storage for 24 h in 37°C water, the bonded teeth were sectioned into hour-glass shaped slices (0.7-mm thick) perpendicular to the bonded surfaces. The specimens were then subjected to microtensile bond strength (μTBS) testing at a crosshead speed of 1.0 mm/min. Data were analyzed with one-way ANOVA and the Tukey-Kramer test. Maintenance spray-contaminated specimens (oil-free and oil-containing spray groups) showed significantly lower μTBS than control specimens (P < 0.05). However, there was no significant difference between the spray-contaminated groups (P > 0.05). Maintenance spray significantly reduces the bond strength of Clearfil SE Bond to dentin.

Comparison of Intrinsic Rate of Different House Fly Densities in a Simulated Condition: A Prediction for House Fly Population and Control Threshold.

PubMed

Ong, Song-Quan; Ahmad, Hamdan; Jaal, Zairi; Rus, Adanan; Fadzlah, Fadhlina Hazwani Mohd

2017-01-01

Determining the control threshold for a pest is common prior to initiating a pest control program; however, previous studies related to the house fly control threshold for a poultry farm are insufficient for determining such a threshold. This study aimed to predict the population changes of house fly population by comparing the intrinsic rate of increase (r m ) for different house fly densities in a simulated system. This study first defined the knee points of a known population growth curve as a control threshold by comparing the r m of five densities of house flies in a simulated condition. Later, to understand the interactions between the larval and adult populations, the correlation between larval and adult capacity rate (r c ) was studied. The r m values of 300- and 500-fly densities were significantly higher compared with the r m values at densities of 50 and 100 flies. This result indicated their representative indices as candidates for a control threshold. The r c of larval and adult populations were negatively correlated with densities of fewer than 300 flies; this implicated adult populations with fewer than 300 flies as declining while the larval population was growing; therefore, control approaches should focus on the immature stages. The results in the present study suggest a control threshold for house fly populations. Future works should focus on calibrating the threshold indices in field conditions. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Feedback enhanced plasma spray tool

DOEpatents

Gevelber, Michael Alan; Wroblewski, Donald Edward; Fincke, James Russell; Swank, William David; Haggard, Delon C.; Bewley, Randy Lee

2005-11-22

An improved automatic feedback control scheme enhances plasma spraying of powdered material through reduction of process variability and providing better ability to engineer coating structure. The present inventors discovered that controlling centroid position of the spatial distribution along with other output parameters, such as particle temperature, particle velocity, and molten mass flux rate, vastly increases control over the sprayed coating structure, including vertical and horizontal cracks, voids, and porosity. It also allows improved control over graded layers or compositionally varying layers of material, reduces variations, including variation in coating thickness, and allows increasing deposition rate. Various measurement and system control schemes are provided.

[Ethyl chloride aerosol spray for local anesthesia before arterial puncture: randomized placebo-controlled trial].

PubMed

Ballesteros-Peña, Sendoa; Fernández-Aedo, Irrintzi; Vallejo-De la Hoz, Gorka

2017-06-01

To compare the efficacy of an ethyl chloride aerosol spray to a placebo spray applied in the emergency department to the skin to reduce pain from arterial puncture for blood gas analysis. Single-blind, randomized placebo-controlled trial in an emergency department of Hospital de Basurto in Bilbao, Spain. We included 126 patients for whom arterial blood gas analysis had been ordered. They were randomly assigned to receive application of the experimental ethyl chloride spray (n=66) or a placebo aerosol spray of a solution of alcohol in water (n=60). The assigned spray was applied just before arterial puncture. The main outcome variable was pain intensity reported on an 11-point numeric rating scale. The median (interquartile range) pain level was 2 (1-5) in the experimental arm and 2 (1-4.5) in the placebo arm (P=.72). Topical application of an ethyl chloride spray did not reduce pain caused by arterial puncture.

mSpray: a mobile phone technology to improve malaria control efforts and monitor human exposure to malaria control pesticides in Limpopo, South Africa.

PubMed

Eskenazi, Brenda; Quirós-Alcalá, Lesliam; Lipsitt, Jonah M; Wu, Lemuel D; Kruger, Philip; Ntimbane, Tzundzukani; Nawn, John Burns; Bornman, M S Riana; Seto, Edmund

2014-07-01

Recent estimates indicate that malaria has led to over half a million deaths worldwide, mostly to African children. Indoor residual spraying (IRS) of insecticides is one of the primary vector control interventions. However, current reporting systems do not obtain precise location of IRS events in relation to malaria cases, which poses challenges for effective and efficient malaria control. This information is also critical to avoid unnecessary human exposure to IRS insecticides. We developed and piloted a mobile-based application (mSpray) to collect comprehensive information on IRS spray events. We assessed the utility, acceptability and feasibility of using mSpray to gather improved homestead- and chemical-level IRS coverage data. We installed mSpray on 10 cell phones with data bundles, and pilot tested it with 13 users in Limpopo, South Africa. Users completed basic information (number of rooms/shelters sprayed; chemical used, etc.) on spray events. Upon submission, this information as well as geographic positioning system coordinates and time/date stamp were uploaded to a Google Drive Spreadsheet to be viewed in real time. We administered questionnaires, conducted focus groups, and interviewed key informants to evaluate the utility of the app. The low-cost, cell phone-based "mSpray" app was learned quickly by users, well accepted and preferred to the current paper-based method. We recorded 2865 entries (99.1% had a GPS accuracy of 20 m or less) and identified areas of improvement including increased battery life. We also identified a number of logistic and user problems (e.g., cost of cell phones and cellular bundles, battery life, obtaining accurate GPS measures, user errors, etc.) that would need to be overcome before full deployment. Use of cell phone technology could increase the efficiency of IRS malaria control efforts by mapping spray events in relation to malaria cases, resulting in more judicious use of chemicals that are potentially harmful to humans and the environment. Copyright © 2014. Published by Elsevier Ltd.

Managing fall armyworm, Spodoptera frugiperda (Lepidoptera: Noctuidae), with Bt maize and insecticides in southern Brazil.

PubMed

Burtet, Leonardo M; Bernardi, Oderlei; Melo, Adriano A; Pes, Maiquel P; Strahl, Thiago T; Guedes, Jerson Vc

2017-12-01

Maize plants expressing insecticidal proteins of Bacillus thuringiensis are valuable options for managing fall armyworm (FAW), Spodoptera frugiperda, in Brazil. However, control failures were reported, and therefore insecticides have been used to control this species. Based on these, we evaluated the use of Bt maize and its integration with insecticides against FAW in southern Brazil. Early-planted Agrisure TL, Herculex, Optimum Intrasect and non-Bt maize plants were severely damaged by FAW and required up to three insecticidal sprays. In contrast, YieldGard VT Pro, YieldGard VT Pro 3, PowerCore, Agrisure Viptera and Agrisure Viptera 3 showed little damage and did not require insecticides. Late-planted Bt maize plants showed significant damage by FAW and required up to four sprays, with the exceptions of Agrisure Viptera and Agrisure Viptera 3. Exalt (first and second sprays); Lannate + Premio (first spray) and Avatar (second spray); and Karate + Match (first spray) and Ampligo (second spray) were the most effective insecticides against FAW larvae in Bt and non-Bt maize. Maize plants expressing Cry proteins exhibited FAW control failures in southern Brazil, necessitating insecticidal sprays. In contrast, Bt maize containing the Vip3Aa20 protein remained effective against FAW. However, regardless of the insecticide used against FAW surviving on Bt maize, grain yields were similar. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Discovery, Development, and Evaluation of a Horn Fly-Isolated (Diptera: Muscidae) Beauveria bassiana (Hypocreales: Cordyciptaceae) Strain From Florida, USA

PubMed Central

Holderman, Christopher J.; Wood, Lois A.; Geden, Christopher J.

2017-01-01

The horn fly, Haematobia irritans (L.) is an important cattle pest and traditionally has been managed using insecticides; however, many horn fly populations are insecticide-resistant in United States. Use of alternative control techniques has been limited because of the challenges of managing a fly pest on pastured cattle. After the discovery of a wild horn fly infected with Beauveria bassiana in Florida, the fungus was cultured and evaluated for efficacy against laboratory-reared horn flies. This fungal strain was selected for increased virulence by passage through laboratory-reared horn fly hosts to shorten interval from infection to fly death and subsequent conidia formation, properties important to future use of the fungus as a biological control agent against horn flies. After seven passages through horn fly hosts, fly mortality was not significantly accelerated as evaluated through LT50 values, but conidia were readily produced from these killed flies. Although further development is needed to improve fungal efficacy, this fungal strain holds promise as a biological control agent for inclusion in horn fly integrated pest management programs. PMID:28423414

9 CFR 355.16 - Control of flies, rats, mice, etc.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Control of flies, rats, mice, etc. 355.16 Section 355.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF....16 Control of flies, rats, mice, etc. Flies, rats, mice, and other vermin shall be excluded from...

9 CFR 355.16 - Control of flies, rats, mice, etc.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Control of flies, rats, mice, etc. 355.16 Section 355.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF....16 Control of flies, rats, mice, etc. Flies, rats, mice, and other vermin shall be excluded from...

9 CFR 355.16 - Control of flies, rats, mice, etc.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Control of flies, rats, mice, etc. 355.16 Section 355.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF....16 Control of flies, rats, mice, etc. Flies, rats, mice, and other vermin shall be excluded from...

9 CFR 355.16 - Control of flies, rats, mice, etc.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Control of flies, rats, mice, etc. 355.16 Section 355.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF....16 Control of flies, rats, mice, etc. Flies, rats, mice, and other vermin shall be excluded from...

9 CFR 355.16 - Control of flies, rats, mice, etc.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Control of flies, rats, mice, etc. 355.16 Section 355.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF....16 Control of flies, rats, mice, etc. Flies, rats, mice, and other vermin shall be excluded from...

Global warming and house fly control: direct effects and biodiversity concerns.

USDA-ARS?s Scientific Manuscript database

House flies are major pests of human and animal health throughout the world and are among the most difficult to control. Effective fly management relies on a balance of sanitation, insecticide use, and biological control. Climate change could upset that balance in favor of the fly unless pro-activ...

Effect of four commercial fungal formulations on mortality and sporulation of house flies (Musca domestica) and stable flies (Stomoxys calcitrans)

USDA-ARS?s Scientific Manuscript database

House flies (Musca domestica L.) and stable flies (Stomoxys calcitrans (L.)) (Diptera: Muscidae) are major pests of livestock. Biological control is an important tool in an integrated control framework. Increased mortality in filth flies has been documented with entomopathogenic fungi, and several s...

Assessing possible exposures of ground troops to Agent Orange during the Vietnam War: the use of contemporary military records.

PubMed

Young, Alvin L; Cecil, Paul F; Guilmartin, John F

2004-01-01

Potential exposure of ground troops in Vietnam to Agent Orange and 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) remains controversial despite the passage of 30 years since the Vietnam War. Because of uncertainty over the serum dioxin levels in ground troops at the end of their service in Vietnam, attempts have been made to develop a methodology for characterizing exposure of ground troops in Vietnam to Agent Orange and other herbicides based upon historical reconstruction from military records. Historical information is often useful in evaluating and modeling exposure, but such information should be reasonably accurate, complete, and reliable. This paper reviews the procedures and supporting historical information related to the spraying of herbicides in Vietnam. The historical information is classified into two categories: procedural information and operational information. Procedural information covered the process and procedures followed in spraying herbicides from US Air Force fixed wing aircraft (Operation RANCH HAND) in Vietnam, and included approval procedures for spray missions, the criteria required to conduct a mission, the control exercised by the Forward Air Controller and the Tactical Air Control Center and the characteristics of the equipment used to apply the herbicides. Operational information includes data from the RANCH HAND Daily Air Activities Reports, which included geographic locations of specific spray missions, the amount of herbicide sprayed by a specific mission, reports of battle damage to spray aircraft, reports of fighter aircraft support for aerial spray missions, and any comments, such as reasons for canceling a mission. Historical information demonstrates that herbicide spray missions were carefully planned and that spraying only occurred when friendly forces were not located in the target area. RANCH HAND spray missions were either not approved or cancelled if approved when there were friendly forces in the area designated for spraying. Stringent criteria had to be met before spray missions could be approved. The operational information shows that spray missions for both defoliation and crop destruction were conducted in an extremely hostile environment. Heavy 'fighter suppression' with antipersonnel ordnance was used to minimize the impact of hostile ground fire on RANCH HAND aircraft. Procedures were in place that prohibited movement of troops into sprayed areas immediately after a mission due to the possible presence of unexploded ordnance delivered by fighter aircraft supporting RANCH HAND missions. The optimal nature of the spray equipment and application procedures minimized the possibility of significant spray drift. Conclusions. Few friendly troops were sprayed by fixed wing aircraft during Operation RANCH HAND, which delivered 95% of all defoliants used in Vietnam. Similarly, few troops were sprayed during helicopter or surface-based spray operations, which constituted the remaining 5% of defoliants. Detailed policies and procedures for approval and execution of spray missions ensured that friendly forces were not located in the areas targeted for spraying. Fighter aircraft assigned to accompany each spray mission frequently suppressed much of the hostile fire with bombs and other ordnance. Confirmed clearance of the target area was necessary to avoid friendly casualties. Historical records establish that these policies and procedures were strictly followed. Exposure of troops whether from direct spraying or movement through areas recently sprayed was very unlikely. The wartime military records of troop positions and herbicide operations are valuable for some purposes, but have specific limitations in exposure reconstruction. The completeness and accuracy of the geographic data (maps used by RANCH HAND and military ground units) were dependent upon the inherent precision of the map, the accuracy with which it depicted surface features, and the completeness and accuracy of the information on which it is based. Navigation by the crew using visual orientation and reference to the map was the only means that aircrew on spray missions had for establishing their locations. A Forward Air Controller independent of Operation RANCH HAND was present at the location of each spray target immediately before and during spraying operations to verify the target location and ensure that friendly forces were clear of the target area. Anecdotal reports of direct spraying of troops in Vietnam likely reflect the RANCH HAND missions spraying insecticide for mosquito control at regular intervals from March 1967 through February 1972. Outlook. The distribution and levels of serum dioxin in RANCH HAND veterans and the US Army Chemical Corps Vietnam veterans (the unit responsible for helicopter and ground-based spray operations) are distinguishable from typical levels in the population decades after the Vietnam conflict. An exposure model similar to that proposed in the 2003 report of the Institute of Medicine's Committee on 'Characterizing Exposure of Veterans to Agent Orange and Other Herbicides Used in Vietnam' was tested in 1988 by the Centers for Disease Control and Prevention and found to be a poor predictor of absorbed dose of TCDD. Military records during the Vietnam War lack the precision to determine that troops were directly sprayed with herbicides during Operation RANCH HAND, especially given the procedures in place to ensure clearance of friendly forces from the target area and the lack of elevated serum levels of TCDD in ground troops judged to have operated in heavily sprayed areas.

Development of process data capturing, analysis and controlling for thermal spray techniques - SprayTracker

NASA Astrophysics Data System (ADS)

Kelber, C.; Marke, S.; Trommler, U.; Rupprecht, C.; Weis, S.

2017-03-01

Thermal spraying processes are becoming increasingly important in high-technology areas, such as automotive engineering and medical technology. The method offers the advantage of a local layer application with different materials and high deposition rates. Challenges in the application of thermal spraying result from the complex interaction of different influencing variables, which can be attributed to the properties of different materials, operating equipment supply, electrical parameters, flow mechanics, plasma physics and automation. In addition, spraying systems are subject to constant wear. Due to the process specification and the high demands on the produced coatings, innovative quality assurance tools are necessary. A central aspect, which has not yet been considered, is the data management in relation to the present measured variables, in particular the spraying system, the handling system, working safety devices and additional measuring sensors. Both the recording of all process-characterizing variables, their linking and evaluation as well as the use of the data for the active process control presuppose a novel, innovative control system (hardware and software) that was to be developed within the scope of the research project. In addition, new measurement methods and sensors are to be developed and qualified in order to improve the process reliability of thermal spraying.

Comparison of the effects of vapocoolant spray and topical anesthetic cream on pain during needle electromyography in the medial gastrocnemius.

PubMed

Moon, Young-Eun; Kim, Sang-Hyun; Choi, Won-Hyeok

2013-05-01

To compare the effects of a vapocoolant spray and an eutectic mixture of local anesthetics (EMLA) cream in reducing pain during needle electromyography examination. Randomized controlled trial. Physical medicine and rehabilitation department of a university hospital. Adults who underwent needle electromyography (N=99) were randomized to 1 of 2 experimental groups or the control group. Two patients dropped out during the study. In the experimental groups, vapocoolant spray or EMLA cream were applied before needle electromyography. In the control group, needle electromyography was performed without pretreatment. Intensity of pain associated with needle electromyography was assessed using a 100-mm visual analog scale (VAS). Patient satisfaction and preference for repeated use were measured using a 5-point Likert scale. VAS score for pain intensity was significantly lower in the spray group (31.9; 95% confidence interval [CI], 22.0-41.7) compared with the control group (52.9; 95% CI, 45.9-60.0; P=.002), whereas there was no significant difference between the EMLA cream group (42.4; 95% CI, 34.2-50.7) and the control group. Patient satisfaction and preference for repeated use were higher in the spray group than the EMLA group. Vapocoolant spray was more effective than EMLA cream in reducing pain during needle electromyography. Copyright © 2013 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

FAST TRACK COMMUNICATION Generation of stable multi-jets by flow-limited field-injection electrostatic spraying and their control via I-V characteristics

NASA Astrophysics Data System (ADS)

Gu, W.; Heil, P. E.; Choi, H.; Kim, K.

2010-12-01

The I-V characteristics of flow-limited field-injection electrostatic spraying (FFESS) were investigated, exposing a new way to predict and control the specific spraying modes from single-jet to multi-jet. Monitoring the I-V characteristics revealed characteristic drops in the current upon formation of an additional jet in the multi-jet spraying mode. For fixed jet numbers, space-charge-limited current behaviour was measured which was attributed to space charge in the dielectric liquids between the needle electrode and the nozzle opening. The present work establishes that FFESS can, in particular, generate stable multiple jets and that their control is possible through monitoring the I-V characteristics. This can allow for automatic control of the FFESS process and expedite its future scientific and industrial applications.

WAYS OF ACQUIRING FLYING PHOBIA.

PubMed

Schindler, Bettina; Vriends, Noortje; Margraf, Jürgen; Stieglitz, Rolf-Dieter

2016-02-01

The few studies that have explored how flying phobia is acquired have produced contradictory results. We hypothesized that classical conditioning plays a role in acquiring flying phobia and investigated if vicarious (model) learning, informational learning through media, and experiencing stressful life events at the time of onset of phobia also play a role. Thirty patients with flying phobia and thirty healthy controls matched on age, sex, and education were interviewed with the Mini-DIPS, the short German version of the Anxiety Disorders Interview Schedule (DSM-IV diagnostic criteria) and the Fear-of-Flying History Interview. Fifty Percent of patients with flying phobia and 53% of healthy controls reported frightening events in the air. There was no significant difference between the two samples. Thus there were not more classical conditioning events for patients with flying phobia. There also was no significant difference between the two samples for vicarious (model) learning: 37% of flying phobia patients and 23% of healthy controls felt influenced by model learning. The influence of informational learning through media was significantly higher for the clinical sample (70%) than for the control group (37%). Patients with flying phobia experienced significantly more stressful life events in the period of their frightening flight experience (60%) than healthy controls (19%). Frightening experiences while flying are quite common, but not everybody develops a flying phobia. Stressful life events and other factors might enhance conditionability. Informational learning through negative media reports probably reinforces the development of flying phobia. Clinical implications are discussed. © 2015 Wiley Periodicals, Inc.

Development and freeze-thaw durability of high flyash-content concrete

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sajadi, J.

1987-01-01

Objectives were to investigate the effects on concrete strength, drying shrinkage, freeze-thaw durability, and air-void system parameters of replacing various amounts of portland cement with different types of fly ash and to compare selected characteristics of such fly-ash concretes and fly-ash concretes containing a high-range water-reducing admixture to those of a control mixture. It was concluded that concrete mixtures with 90-day compressive strengths equal to the control could be produced when large amounts of cement were replaced by fly ash. In addition, when the high-range water-reducing admixtures was employed, very large amounts of cement could be replaced by fly ashmore » to yield mixtures whose compressive strengths were equal to or greater than the strengths of the control mix at all ages. The maximum amount of cement that could be replaced for equal-strength mixtures depended upon the nature of the fly ash. Drying shrinkage of plain fly-ash concretes and fly-ash concretes containing the high-range water-reducing admixture were similar to those of the control mix. The optimum fly-ash content in a concrete is comparable in strength and durability to a conventional (control) concrete was influenced by the chemical and physical characteristics of the fly ash.« less

Comparison of lidocaine spray and paracervical block application for pain relief during first-trimester surgical abortion: A randomised, double-blind, placebo-controlled trial.

PubMed

Aksoy, Huseyin; Aksoy, Ulku; Ozyurt, Sezin; Ozoglu, Nil; Acmaz, Gokhan; Aydın, Turgut; İdem Karadağ, Özge; Tayyar, Ahter Tanay

2016-07-01

Surgical abortion is one of the most frequently performed gynaecological procedures and its associated pain has always been a problem in gynaecology. Here we studied the analgesic efficacy of lidocaine spray and paracervical block (PCB) in patients undergoing first-trimester surgical abortion. A randomised double-blind placebo-controlled study was conducted on 108 women requesting pregnancy termination. The subjects were randomly assigned into four groups: Group 1 (PCB plus lidocaine spray) (n=27), Group 2 (PCB) (n=27), Group 3 (lidocaine spray) (n=27) and Group 4 (placebo) (n=27). Intra-procedural and post-procedural pain scores were measured with a standard visual analogue scale (VAS). The median VAS scores during procedure in placebo, lidocaine spray, PCB plus lidocaine spray and PCB groups were 8 (7-9), 5 (4-8), 4 (3-4) and 5 (3-5), respectively. The most effective method of pain relief during first-trimester abortion can be achieved through a combined use of PCB plus lidocaine spray. Therefore, lidocaine spray is a non-invasive complementary anaesthetic method versus traditional PCB for first-trimester surgical abortion.

Treatment of horses with cypermethrin against the biting flies Culicoides nubeculosus, Aedes aegypti and Culex quinquefasciatus.

PubMed

Papadopoulos, E; Rowlinson, M; Bartram, D; Carpenter, S; Mellor, P; Wall, R

2010-04-19

An in vitro assay was used to assess the efficacy of the proprietary pyrethroid insecticide cypermethrin applied to horses (Deosect spray, 5.0%, w/v Fort Dodge Animal Health) against the biting midge Culicoides nubeculosus (Meigen) (Diptera: Ceratopogonidae) and the mosquitoes Aedes aegypti Linneaus and Culex quinquefasciatus Say (Diptera: Culicidae). Hair was collected from the back, belly and legs of the horses immediately prior to treatment and 7, 14, 21, 28 and 35 days after treatment, and also from untreated controls. In laboratory assays groups of 10 adult female C. nubeculosus, Ae. aegypti or C. quinquefasciatus were exposed to 0.5g of hair for 3min. In all cases, little or no mortality was observed in insects kept in contact with the pre-treatment samples or the untreated controls. With post-treatment samples for C. nubeculosus, mortality was close to 80% 7 days after treatment and then declined gradually; mean mortality was still at around 50% for hair collected 35 days after treatment. In general, Ae. aegypti and C. quinquefasciatus appeared to be less susceptible to cypermethrin than C. nubeculosus and the attenuation of the toxic effect declined more quickly with time after treatment. There were differences in the toxicity of hair from different body regions, with hair from the back consistently inducing the highest mortality and hair from the legs the lowest; this effect was more pronounced for C. nubeculosus than Ae. aegypti or C. quinquefasciatus. The results demonstrate the potential for topical insecticide treatment to offer protection to horses against biting flies; but highlight the major differences that exist in susceptibility between different insect species.

Nano spray-dried sodium chloride and its effects on the microbiological and sensory characteristics of surface-salted cheese crackers.

PubMed

Moncada, Marvin; Astete, Carlos; Sabliov, Cristina; Olson, Douglas; Boeneke, Charles; Aryana, Kayanush J

2015-09-01

Reducing particle size of salt to approximately 1.5 µm would increase its surface area, leading to increased dissolution rate in saliva and more efficient transfer of ions to taste buds, and hence, perhaps, a saltier perception of foods. This has a potential for reducing the salt level in surface-salted foods. Our objective was to develop a salt using a nano spray-drying method, to use the developed nano spray-dried salt in surface-salted cheese cracker manufacture, and to evaluate the microbiological and sensory characteristics of cheese crackers. Sodium chloride solution (3% wt/wt) was sprayed through a nano spray dryer. Particle sizes were determined by dynamic light scattering, and particle shapes were observed by scanning electron microscopy. Approximately 80% of the salt particles produced by the nano spray dryer, when drying a 3% (wt/wt) salt solution, were between 500 and 1,900 nm. Cheese cracker treatments consisted of 3 different salt sizes: regular salt with an average particle size of 1,500 µm; a commercially available Microsized 95 Extra Fine Salt (Cargill Salt, Minneapolis, MN) with an average particle size of 15 µm; and nano spray-dried salt with an average particle size of 1.5 µm, manufactured in our laboratory and 3 different salt concentrations (1, 1.5, and 2% wt/wt). A balanced incomplete block design was used to conduct consumer analysis of cheese crackers with nano spray-dried salt (1, 1.5, and 2%), Microsized salt (1, 1.5, and 2%) and regular 2% (control, as used by industry) using 476 participants at 1wk and 4mo. At 4mo, nano spray-dried salt treatments (1, 1.5, and 2%) had significantly higher preferred saltiness scores than the control (regular 2%). Also, at 4mo, nano spray-dried salt (1.5 and 2%) had significantly more just-about-right saltiness scores than control (regular 2%). Consumers' purchase intent increased by 25% for the nano spray-dried salt at 1.5% after they were notified about the 25% reduction in sodium content of the cheese cracker. We detected significantly lower yeast counts for nano spray-dried salt treatments (1, 1.5, and 2%) at 4mo compared with control (regular) salt (1, 1.5 and 2%). We detected no mold growth in any of the treatments at any time. At 4mo, we found no significant differences in sensory color, aroma, crunchiness, overall liking, or acceptability scores of cheese crackers using 1.5 and 1% nano spray-dried salt compared with control. Therefore, 25 to 50% less salt would be suitable for cheese crackers if the particle size of regular salt was reduced 3 log to form nano spray-dried salt. A 3-log reduction in sodium chloride particle size from regular salt to nano spray-dried salt increased saltiness, but a 1-log reduction in salt size from Microsized salt to nano spray-dried salt did not increase saltiness of surface-salted cheese crackers. The use of salt with reduced particle size by nano spray drying is recommended for use in surface-salted cheese crackers to reduce sodium intake. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Comparison of the performance between a spray gun and a spray boom in ornamentals.

PubMed

Foqué, D; Nuyttens, D

2011-01-01

Flemish greenhouse growers predominantly use handheld spray guns and spray lances for their crop protection purposes although these techniques are known for their heavy workload and their high operator exposure risks. Moreover, when these techniques are compared with spray boom equipment, they are often found to be less effective. On the other hand, handheld spraying techniques are less expensive and more flexible to use. Additionally, many Flemish growers are convinced that a high spray volume and spray pressure is needed to assure a good plant protection. The aim of this work was to evaluate and compare the spray deposition, penetration and uniformity between a manually pulled horizontal spray boom and a spray gun under controlled laboratory conditions. In total, six different spray application techniques were evaluated. In general, the total deposition results were comparable between the spray boom and the spray gun applications but the boom applications resulted in a more uniform spray distribution over the crop. On a plant level, the spray distribution was not uniform for the different techniques with highest deposits on the upper side of the top leaves. Using spray guns at a higher spray pressure did not improve spray penetration and deposition on the bottom side of the leaves. From the different nozzle types, the XR 80 03 gave the best results. Plant density clearly affected crop penetration and deposition on the bottom side of the leaves.

Determining the drift potential of Venturi nozzles compared with standard nozzles across three insecticide spray solutions in a wind tunnel.

PubMed

Ferguson, J Connor; Chechetto, Rodolfo G; O'Donnell, Chris C; Dorr, Gary J; Moore, John H; Baker, Greg J; Powis, Kevin J; Hewitt, Andrew J

2016-08-01

Previous research has sought to adopt the use of drift-reducing technologies (DRTs) for use in field trials to control diamondback moth (DBM) Plutella xylostella (L.) (Lepidoptera: Plutellidae) in canola (Brassica napus L.). Previous studies observed no difference in canopy penetration from fine to coarse sprays, but the coverage was higher for fine sprays. DBM has a strong propensity to avoid sprayed plant material, putting further pressure on selecting technologies that maximise coverage, but often this is at the expense of a greater drift potential. This study aims to examine the addition of a DRT oil that is labelled for control of DBM as well and its effect on the drift potential of the spray solution. The objectives of the study are to quantify the droplet size spectrum and spray drift potential of each nozzle type to select technologies that reduce spray drift, to examine the effect of the insecticide tank mix at both (50 and 100 L ha(-1) ) application rates on droplet size and spray drift potential across tested nozzle type and to compare the droplet size results of each nozzle by tank mix against the drift potential of each nozzle. The nozzle type affected the drift potential the most, but the spray solution also affected drift potential. The fine spray quality (TCP) resulted in the greatest drift potential (7.2%), whereas the coarse spray quality (AIXR) resulted in the lowest (1.3%), across all spray solutions. The spray solutions mixed at the 100 L ha(-1) application volume rate resulted in a higher drift potential than the same products mixed at the 50 L ha(-1) mix rate. The addition of the paraffinic DRT oil was significant in reducing the drift potential of Bacillus thuringiensis var. kurstkai (Bt)-only treatments across all tested nozzle types. The reduction in drift potential from the fine spray quality to the coarse spray quality was up to 85%. The addition of a DRT oil is an effective way to reduce the spray solution drift potential across all nozzle types and tank mixes evaluated in this study. The greatest reduction in drift potential can be achieved by changing nozzle type, which can reduce the losses of the spray to the surrounding environment. Venturi nozzles greatly reduce the drift potential compared with standard nozzles by as much as 85% across all three insecticide spray solutions. Results suggest that a significant reduction in drift potential can be achieved by changing the nozzle type, and can be achieved without a loss in control of DBM. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Dengue vector control: present status and future prospects.

PubMed

Yap, H H; Chong, N L; Foo, A E; Lee, C Y

1994-12-01

Dengue Fever (DF) and Dengue Haemorrhagic Fever (DHF) have been the most common urban diseases in Southeast Asia since the 1950s. More recently, the diseases have spread to Central and South America and are now considered as worldwide diseases. Both Aedes aegypti and Aedes albopictus are involved in the transmission of DF/DHF in Southeast Asian region. The paper discusses the present status and future prospects of Aedes control with reference to the Malaysian experience. Vector control approaches which include source reduction and environmental management, larviciding with the use of chemicals (synthetic insecticides and insect growth regulators and microbial insecticide), and adulticiding which include personal protection measures (household insecticide products and repellents) for long-term control and space spray (both thermal fogging and ultra low volume sprays) as short-term epidemic measures are discussed. The potential incorporation of IGRs and Bacillus thuringiensis-14 (Bti) as larvicides in addition to insecticides (temephos) is discussed. The advantages of using water-based spray over the oil-based (diesel) spray and the use of spray formulation which provide both larvicidal and adulticidal effects that would consequently have greater impact on the overall vector and disease control in DF/DHF are highlighted.

An application of digital image processing techniques to the characterization of liquid petroleum gas (LPG) spray

NASA Astrophysics Data System (ADS)

Qi, Y. L.; Xu, B. Y.; Cai, S. L.

2006-12-01

To control fuel injection, optimize combustion and reduce emissions for LPG (liquefied petroleum gas) engines, it is necessary and important to understand the characteristics of LPG sprays. The present work investigates the geometry of LPG sprays, including spray tip penetration, spray angle, projected spray area and spray volume, by using schlieren photography and digital image processing techniques. Two types of single nozzle injectors were studied, with the same nozzle diameter, but one with and one without a double-hole flow-split head. A code developed to analyse the results directly from the digitized images is shown to be more accurate and efficient than manual measurement and analysis. Test results show that a higher injection pressure produces a longer spray tip penetration, a larger projected spray area and spray volume, but a smaller spray cone angle. The injector with the double-hole split-head nozzle produces better atomization and shorter tip penetration at medium and late injection times, but longer tip penetration in the early stage.

Computational Fluid Dynamics Analysis of High Injection Pressure Blended Biodiesel

NASA Astrophysics Data System (ADS)

Khalid, Amir; Jaat, Norrizam; Faisal Hushim, Mohd; Manshoor, Bukhari; Zaman, Izzuddin; Sapit, Azwan; Razali, Azahari

2017-08-01

Biodiesel have great potential for substitution with petrol fuel for the purpose of achieving clean energy production and emission reduction. Among the methods that can control the combustion properties, controlling of the fuel injection conditions is one of the successful methods. The purpose of this study is to investigate the effect of high injection pressure of biodiesel blends on spray characteristics using Computational Fluid Dynamics (CFD). Injection pressure was observed at 220 MPa, 250 MPa and 280 MPa. The ambient temperature was kept held at 1050 K and ambient pressure 8 MPa in order to simulate the effect of boost pressure or turbo charger during combustion process. Computational Fluid Dynamics were used to investigate the spray characteristics of biodiesel blends such as spray penetration length, spray angle and mixture formation of fuel-air mixing. The results shows that increases of injection pressure, wider spray angle is produced by biodiesel blends and diesel fuel. The injection pressure strongly affects the mixture formation, characteristics of fuel spray, longer spray penetration length thus promotes the fuel and air mixing.

Emergency mosquito aerial spray response to the 2004 Florida hurricanes Charley, Frances, Ivan, and Jeanne: an overview of control results.

PubMed

Simpson, Jennifer E

2006-09-01

In total, 43 aerial spray missions were conducted in 26 Florida counties to control mosquito populations after each of the 4 hurricanes making landfall in Florida in 2004. Mosquitoes were trapped before and after each spray mission to determine the percentage (%) of control for the West Nile virus vector Culex nigripalpus (64.1%), the floodwater pest mosquito Psorophora columbiae (69.7%), and for all species combined (67.7%). A discussion on these results and suggestions for future efforts are presented.

Aerial spray adjuvants for herbicidal drift control.

Treesearch

Gratkowski H.; Stewart R.

1973-01-01

Increased public concern about pesticides requires that foresters reduce drift and insure precise application of herbicides to the areas requiring treatment. Drift control is necessary near waterways and other ecologically sensitive areas. This publication discusses available drift control adjuvants for herbicidal sprays. These include invert emulsions, thickening...

An electronic flow control system for a variable-rate tree sprayer

USDA-ARS?s Scientific Manuscript database

Precise modulation of nozzle flow rates is a critical measure to achieve variable-rate spray applications. An electronic flow rate control system accommodating with microprocessors and pulse width modulation (PWM) controlled solenoid valves was designed to manipulate the output of spray nozzles inde...

Observations of severe in-flight environments on airplane composite structural components

NASA Technical Reports Server (NTRS)

Howell, W. E.; Fisher, B. D.

1983-01-01

The development of relatively inexpensive, highly sophisticated avionics systems makes it now possible for general aviation aircraft to fly under more severe weather conditions than formerly. Increased instrument flying increases exposure of aircraft to potentially severe thunderstorm activity such as high rain rates, hail stones, and lightning strikes. In particular, the effects of lightning on aircraft can be catastrophic. Interest in aircraft lightning protection has been stimulated by the introduction of advanced composites as an aircraft structural material. The present investigation has the objective to report experiences with three composite components which have flown in thunderstorms, taking into account three F-106B composite fin caps. The only visible lightning strike damage to a flame sprayed aluminum coated glass/epoxy fin cap was a small area of the aluminum which was burned. Visible lightning strike damage to a Kevlar/epoxy fin cap was limited to the exterior ply of aluminum coated glass fabric. In the case of a graphite/epoxy fin cap, lightning currents could be conducted.

Aeronautical Research Engineer Milt Thompson computing data

NASA Technical Reports Server (NTRS)

1956-01-01

Milton O. Thompson was hired as an engineer at the National Advisory Committee for Aeronautics' High-Speed Flight Station (later renamed the National Aeronautics and Space Administration's Dryden Flight Research Center) on March 19, 1956. In 1958 he became a research pilot, but in this photo Milt is working on data from another pilot's research flight. Thompson began flying with the U.S. Navy as a pilot trainee at the age of 19. He subsequently served during World War II, with duty in China and Japan. Following six years of active naval service, he entered the University of Washington, in Seattle, Washington. Milt graduated in 1953 with a Bachelor of Science degree in Engineering. He remained in the Naval Reserves during college, and continued flying--not only naval aircraft but crop dusters and forest-spraying aircraft. After college graduation, Milt became a flight test engineer for the Boeing Aircraft Company in Seattle, where he was employed for two years before coming to the High-Speed Flight Station.

Small mammal populations in Maryland meadows during four years of herbicide (brominal®) applications

USGS Publications Warehouse

Clark, D.R.; Moulton, C.A.; Hines, J.E.; Hoffman, D.J.

1996-01-01

The herbicide Brominal® was applied at the recommended rate to one plot in each of three paired 0.6-ha plots; the other three plots were used as controls. Plots were sprayed once in the fall of 1988 and 1989 and twice in the spring of 1990 and 1991. Small mammals were trapped three times during each activity season (April-October) to obtain population estimates before and after spraying and in the spring preceding fall spraying or the fall following spring spraying. Population estimates immediately after spraying gave no evidence of direct mortality. By 1991, dicot vegetation on treated plots was suppressed and mean numbers of meadow voles (Microtus pennsylvanicus) were less than on control plots. Because meadow voles favor dicots over monocots in their diet, reduced availability of dicots may have been related to the smaller vole population estimates. Species diversity of small mammals was negatively correlated with size of vole populations, but was not different between treated and control plots. Brominal apparently induced opaque corneas in nine voles. The condition was found in two voles too small to have been conceived at the time of the last previous spray nearly 8 months earlier, suggesting exposure to residue alone.

Village-scale (Phase III) evaluation of the efficacy and residual activity of SumiShield® 50 WG (Clothianidin 50%, w/w) for indoor spraying for the control of pyrethroid-resistant Anopheles culicifacies Giles in Karnataka state, India.

PubMed

Uragayala, S; Kamaraju, R; Tiwari, S N; Sreedharan, S; Ghosh, S K; Valecha, N

2018-06-01

There is an urgent need to test and incorporate new molecules with promising efficacy and novel mode of action to control insecticide-resistant mosquito vectors for disease control. We tested a new compound, clothianidin (SumiShield 50 WG), for its efficacy as an indoor residual spray (IRS) for the control of pyrethroid-resistant Anopheles culicifacies (Diptera: Culicidae) in comparison with pirimiphos methyl (Actellic CS) as a positive control. Ten villages were selected, five each for IRS with clothianidin (300 mg AI/m 2 ) and pirimiphos methyl (1000 mg AI/m 2 ) in Almatti Dam catchment area in Karnataka state, India. Entomological parameters were monitored in these sprayed villages using standard methods. Assessment of quality of spray was performed by analysing the insecticide content in the filter paper samples collected from sprayed houses. Perceptions of spray men and inhabitants were recorded post-spray on safety of these molecules. The mean applied to target ratio of content was 1.7 (n = 29) for clothianidin and 1.8 (n = 50) for pirimiphos methyl on filter paper samples analysed. Residual activity (≥80% mortality in exposed mosquitoes) after 24 h post-exposure of SumiShield WG was 5 months and increased to 6 months when the holding period was extended to 120 h and that of Actellic CS was 3 months at 24-h holding period and extended to 4 months at 120-h extended holding period. The mean densities of An. culicifacies in both arms fell drastically post-spray. In light trap collections, density of mosquitoes collected indoors was lower than outdoors in both arms indicating effectiveness of IRS. SumiShield WG was more efficacious in reducing the per-structure density than Actellic CS. The proportion of nulliparous mosquitoes was higher than that of parous mosquitoes during post-spray collections in both arms. The majority of adverse events reported were transitory and subsided without medication. Indoor residual spraying with SumiShield WG was found effective, operationally feasible and safe, and it is effective for up to 6 months. © 2018 John Wiley & Sons Ltd.

The Influence of Atmospheric Stability on Wind Drift from Ultra-Low-volume Aerial Forest Spray Applications.

NASA Astrophysics Data System (ADS)

Crabbe, R. S.; McCooeye, M.; Mickle, R. E.

1994-04-01

Measurements of drift cloud mass from 11 cases selected from a study of wind-borne droplet drift from ultra low-volume aerial spray applications over northern Ontario forests are presented as a function of atmospheric stability. Six swaths were overlaid onto a flight line in 30 min to obtain ensemble-averaged data from rotary atomizer emissions from an agricultural spray plane flying at about 21 and 26 m above ground level. The estimated volume median diameters of the spray were 100 µm for the 21-m height and 70 µm for the 26-m height. The mass of spray material in the drift cloud was measured at 400, 1200, and 2200 m downwind of the (crosswind) flight line using Rotorods' suspended from tethered blimps. Wind speed at aircraft height varied from 2 to 5 m s1 and meteorological conditions varied from moderately stable to moderately unstable.Analysis of the data revealed that 35% more drift occurred in stable than in unstable conditions. The lowest drift was measured when the aircraft was flown in the morning mixing layer beneath a low capping inversion. Under thee conditions, only 18% of the emission drifted put 400 m downwind and 10% past 1200 m. The highest drift occurred in moderately stable flow, 71% past 400 m and 50% past 2200 m in 3 m s1 wind speeds and, in slightly stable flow, 77% past 400 m and 27% past 2200 m in 5 m s1 wind speeds.Within experimental error, little difference was observed between wind drift of the 100-µm-diameter droplets and the 70-µm-diameter droplets past 400 m downwind although farther downwind, drift from the larger-droplet emission was less. This difference is discussed in terms of the descent rate of the aircraft vortex wake in stable conditions.

Adaptive individual-cylinder thermal state control using piston cooling for a GDCI engine

DOEpatents

Roth, Gregory T; Husted, Harry L; Sellnau, Mark C

2015-04-07

A system for a multi-cylinder compression ignition engine includes a plurality of nozzles, at least one nozzle per cylinder, with each nozzle configured to spray oil onto the bottom side of a piston of the engine to cool that piston. Independent control of the oil spray from the nozzles is provided on a cylinder-by-cylinder basis. A combustion parameter is determined for combustion in each cylinder of the engine, and control of the oil spray onto the piston in that cylinder is based on the value of the combustion parameter for combustion in that cylinder. A method for influencing combustion in a multi-cylinder engine, including determining a combustion parameter for combustion taking place in in a cylinder of the engine and controlling an oil spray targeted onto the bottom of a piston disposed in that cylinder is also presented.

Response of breeding birds to aerial sprays of trichlorfon (Dylox) and carbaryl (Sevin-4-Oil) in Montana forests

USGS Publications Warehouse

DeWeese, L.R.; Henny, C.J.; Floyd, R.L.; Bobal, K.A.; Schultz, A.W.

1979-01-01

Breeding density, food, nesting success, and mortality of 20 bird species were monitored at Beaverhead National Forest, Montana, in 1975 in conjunction with experimental applications of trichlorfon (Dylox) and carbaryl (Sevin-4-oil) to western budworms (Choristoneura occidentalis). Bird species on nine 350- to 550-ha forested plots (three controls and three treated with each pesticide) were studied before and for 14 days after the spraying of trichlorfon at 1.1 kg in?9.4 L of Panasol AN3 per ha (1 pound active ingredient in 1.0 gallon/acre) and of carbaryl at 1.1 kg in 4.7 L of diesel oil per ha (l pound active ingredient in 0.5 gallon/acre). No significant decrease in bird numbers was detected from breeding-pair estimates or live bird counts after the spraying. Of the breeding pairs present before spraying, 92% remained on control plots, 89% on trichlorfon plots, and 92% on carbaryl plots. Counts of live birds made before and after spraying in three types of habitat supported the. results of the breeding-pair estimates. Nests with eggs or with young at the time of spraying were 74 and 97% successful, respectively, in control plots, 83 and 100% in plots sprayed with trichlorfon, and 86 and 100% in plots sprayed with carbaryl. No sick or dead birds were found after the spraying, although budworms were found in bird stomachs, and tracer-dye from the pesticide occurred on the feathers or feet of 74% of the 202 birds collected. Species dwelling in the tree canopy encountered the dye (and thus the pesticide) at a slightly higher rate (80%) than did species below the treetops (71 %) or near the ground and in open areas (70%).

Cost of standard indoor ultra-low-volume space spraying as a method to control adult dengue vectors.

PubMed

Ditsuwan, Thanittha; Liabsuetrakul, Tippawan; Ditsuwan, Vallop; Thammapalo, Suwich

2012-06-01

To access the costs of standard indoor ultra-low-volume (SID-ULV) space spraying for controlling dengue vectors in Thailand. Resources related to SID-ULV space spraying as a method to control dengue vectors between July and December 2009 were identified, measured and valued taking a societal perspective into consideration. Information on costs was collected from direct observations, interviews and bookkeeping records. Uncertainty of unit costs was investigated using a bootstrap technique. Costs of SID-ULV were calculated from 18 new dengue cases that covered 1492 surrounding houses. The average coverage of the SID-ULV was 64.4%. In the first round of spraying, 53% of target houses were sprayed and 44.6% in the second round, of which 69.2% and 54.7% received entire indoor space spraying. Unit costs per case, per 10 houses and per 100 m(2) were USD 705 (95% Confidence Interval CI, 539-888), 180 (95% CI, 150-212) and USD 23 (95% CI, 17-30). The majority of SID-ULV unit cost per case was attributed to productivity loss (83.9%) and recurrent costs (15.2%). The unit cost of the SID-ULV per case and per house in rural was 2.8 and 1.6 times lower than municipal area. The estimated annual cost of SID-ULV space spraying from 2005 to 2009 using healthcare perspective ranged from USD 5.3 to 10.3 million. The majority of the cost of SID-ULV space spraying was attributed to productivity loss. Potential productivity loss influences the achievement of high coverage, so well-planned SID-ULV space spraying strategies are needed to reduce costs. © 2012 Blackwell Publishing Ltd.

Formulation development of the biocontrol agent Bacillus subtilis strain CPA-8 by spray-drying.

PubMed

Yánez-Mendizábal, V; Viñas, I; Usall, J; Torres, R; Solsona, C; Abadias, M; Teixidó, N

2012-05-01

To prepare commercially acceptable formulations of Bacillus subtilis CPA-8 by spray-drying with long storage life and retained efficacy to control peach and nectarine brown rot caused by Monilinia spp. CPA-8 24-h- and 72-h-old cultures were spray dried using 10% skimmed milk, 10% skimmed milk plus 10% MgSO(4) , 10% MgSO(4) and 20% MgSO(4) as carriers/protectants. All carriers/protectants gave good percentages of powder recovery (28-38%) and moisture content (7-13%). CPA-8 survival varied considerably among spray-dried 24-h- and 72-h-old cultures. Seventy-two hours culture spray dried formulations showed the highest survival (28-32%) with final concentration products of 1·6-3·3 × 10(9) CFU g(-1) , while viability of 24-h-old formulations was lower than 1%. Spray-dried 72-h-old formulations were selected to subsequent evaluation. Rehydration of cells with water provided a good recovery of CPA-8 dried cells, similar to other complex rehydration media tested. Spray-dried formulations stored at 4 ± 1 and 20 ± 1°C showed good shelf life during 6 months, and viability was maintained or slightly decreased by 0·2-0·3-log. CPA-8 formulations after 4- and 6 months storage were effective in controlling brown rot caused by Monilinia spp. on nectarines and peaches resulting in a 90-100% reduction in disease incidence. Stable and effective formulations of biocontrol agent B. subtilis CPA-8 could be obtained by spray-drying. New shelf-stable and effective formulations of a biocontrol agent have been obtained by spray-drying to control brown rot on peach. © 2012 The Authors. Journal of Applied Microbiology © 2012 The Society for Applied Microbiology.

Simulation of preburner sprays, volumes 1 and 2

NASA Technical Reports Server (NTRS)

Hardalupas, Y.; Whitelaw, J. H.

1993-01-01

The present study considered characteristics of sprays under a variety of conditions. Control of these sprays is important as the spray details can control both rocket combustion stability and efficiency. Under the present study Imperial College considered the following: (1) Measurement of the size and rate of spread of the sprays produced by single coaxial airblast nozzles with axial gaseous stream. The local size, velocity, and flux characteristics for a wide range of gas and liquid flowrates were measured, and the results were correlated with the conditions of the spray at the nozzle exit. (2) Examination of the effect of the geometry of single coaxial airblast atomizers on spray characteristics. The gas and liquid tube diameters were varied over a range of values, the liquid tube recess was varied, and the shape of the exit of the gaseous jet was varied from straight to converging. (3) Quantification of the effect of swirl in the gaseous stream on the spray characteristics produced by single coaxial airblast nozzles. (4) Quantification of the effect of reatomization by impingement of the spray on a flat disc positioned around 200 mm from the nozzle exit. This models spray impingement on the turbopump dome during the startup process of the preburner of the SSME. (5) Study of the interaction between multiple sprays without and with swirl in their gaseous stream. The spray characteristics of single nozzles were compared with that of three identical nozzles with their axis at a small distance from each other. This study simulates the sprays in the preburner of the SSME, where there are around 260 elements on the faceplate of the combustion chamber. (6) Design an experimental facility to study the characteristics of sprays at high pressure conditions and at supercritical pressure and temperature for the gas but supercritical pressure and subcritical temperature for the liquid.

Implications of bio-efficacy and persistence of insecticides when indoor residual spraying and long-lasting insecticide nets are combined for malaria prevention

PubMed Central

2012-01-01

Background Bio-efficacy and residual activity of insecticides used for indoor residual spraying (IRS) and long-lasting insecticide nets (LLINs) were assessed against laboratory-reared and wild populations of the malaria vector, Anopheles arabiensis in south eastern Tanzania. Implications of the findings are examined in the context of potential synergies and redundancies where IRS and LLINs are combined. Methods Bioassays were conducted monthly for six months on three LLIN types (Olyset® PermaNet 2.0®,and Icon Life®) and three IRS treatments (2 g/m2 pirimiphos-methyl, 2 g/m2 DDT and 0.03 g/m2 lambda-cyhalothrin, sprayed on mud walls and palm ceilings of experimental huts). Tests used susceptible laboratory-reared An. arabiensis exposed in cones (nets and IRS) or wire balls (nets only). Susceptibility of wild populations was assessed using WHO diagnostic concentrations and PCR for knock-down resistance (kdr) genes. Results IRS treatments killed ≥ 85% of mosquitoes exposed on palm ceilings and ≥ 90% of those exposed on mud walls, but up to 50% of this toxicity decayed within 1–3 months, except for DDT. By 6th month, only 7.5%, 42.5% and 30.0% of mosquitoes died when exposed to ceilings sprayed with pirimiphos-methyl, DDT or lambda-cyhalothrin respectively, while 12.5%, 36.0% and 27.5% died after exposure to mud walls sprayed with the same insecticides. In wire-ball assays, mortality decreased from 98.1% in 1st month to 92.6% in 6th month in tests on PermaNet 2.0®, from 100% to 61.1% on Icon Life® and from 93.2% to 33.3% on Olyset® nets. In cone bioassays, mortality reduced from 92.8% in 1st month to 83.3% in 6th month on PermaNet 2.0®, from 96.9% to 43.80% on Icon Life® and from 85.6% to 14.6% on Olyset®. Wild An. arabiensis were 100% susceptible to DDT, 95.8% to deltamethrin, 90.2% to lambda cyhalothrin and 95.2% susceptible to permethrin. No kdr gene mutations were detected. Conclusions In bioassays where sufficient contact with treated surfaces is assured, LLINs and IRS kill high proportions of susceptible An. arabiensis mosquitoes, though these efficacies decay gradually for LLINs and rapidly for IRS. It is, therefore, important to always add intact nets in sprayed houses, guaranteeing protection even after the IRS decays, and to ensure accurate timing, quality control and regular re-spraying in IRS programmes. By contrast, adding IRS in houses with intact LLINs is unlikely to improve protection relative to LLINs alone, since there is no guarantee that unfed vectors would rest long enough on the sprayed surfaces, and because of the rapid IRS decay. However, there is need to clarify these effects using data from observations of free flying mosquitoes in huts. Physiological susceptibility of An. arabiensis in the area remains 100% against DDT, but is slightly reduced against pyrethroids, necessitating caution over possible spread of resistance. The loss of LLIN toxicity, particularly Olyset® nets suggests that protection offered by these nets against An. arabiensis may be primarily due to physical bite prevention rather than insecticidal efficacy. PMID:23164062

Implications of bio-efficacy and persistence of insecticides when indoor residual spraying and long-lasting insecticide nets are combined for malaria prevention.

PubMed

Okumu, Fredros O; Chipwaza, Beatrice; Madumla, Edith P; Mbeyela, Edgar; Lingamba, Geoffrey; Moore, Jason; Ntamatungro, Alex J; Kavishe, Deo R; Moore, Sarah J

2012-11-19

Bio-efficacy and residual activity of insecticides used for indoor residual spraying (IRS) and long-lasting insecticide nets (LLINs) were assessed against laboratory-reared and wild populations of the malaria vector, Anopheles arabiensis in south eastern Tanzania. Implications of the findings are examined in the context of potential synergies and redundancies where IRS and LLINs are combined. Bioassays were conducted monthly for six months on three LLIN types (Olyset® PermaNet 2.0®,and Icon Life®) and three IRS treatments (2 g/m2 pirimiphos-methyl, 2 g/m2 DDT and 0.03 g/m2 lambda-cyhalothrin, sprayed on mud walls and palm ceilings of experimental huts). Tests used susceptible laboratory-reared An. arabiensis exposed in cones (nets and IRS) or wire balls (nets only). Susceptibility of wild populations was assessed using WHO diagnostic concentrations and PCR for knock-down resistance (kdr) genes. IRS treatments killed ≥ 85% of mosquitoes exposed on palm ceilings and ≥ 90% of those exposed on mud walls, but up to 50% of this toxicity decayed within 1-3 months, except for DDT. By 6th month, only 7.5%, 42.5% and 30.0% of mosquitoes died when exposed to ceilings sprayed with pirimiphos-methyl, DDT or lambda-cyhalothrin respectively, while 12.5%, 36.0% and 27.5% died after exposure to mud walls sprayed with the same insecticides. In wire-ball assays, mortality decreased from 98.1% in 1st month to 92.6% in 6th month in tests on PermaNet 2.0®, from 100% to 61.1% on Icon Life® and from 93.2% to 33.3% on Olyset® nets. In cone bioassays, mortality reduced from 92.8% in 1st month to 83.3% in 6th month on PermaNet 2.0®, from 96.9% to 43.80% on Icon Life® and from 85.6% to 14.6% on Olyset®. Wild An. arabiensis were 100% susceptible to DDT, 95.8% to deltamethrin, 90.2% to lambda cyhalothrin and 95.2% susceptible to permethrin. No kdr gene mutations were detected. In bioassays where sufficient contact with treated surfaces is assured, LLINs and IRS kill high proportions of susceptible An. arabiensis mosquitoes, though these efficacies decay gradually for LLINs and rapidly for IRS. It is, therefore, important to always add intact nets in sprayed houses, guaranteeing protection even after the IRS decays, and to ensure accurate timing, quality control and regular re-spraying in IRS programmes. By contrast, adding IRS in houses with intact LLINs is unlikely to improve protection relative to LLINs alone, since there is no guarantee that unfed vectors would rest long enough on the sprayed surfaces, and because of the rapid IRS decay. However, there is need to clarify these effects using data from observations of free flying mosquitoes in huts. Physiological susceptibility of An. arabiensis in the area remains 100% against DDT, but is slightly reduced against pyrethroids, necessitating caution over possible spread of resistance. The loss of LLIN toxicity, particularly Olyset® nets suggests that protection offered by these nets against An. arabiensis may be primarily due to physical bite prevention rather than insecticidal efficacy.

Space shuttle flying qualities and criteria assessment

NASA Technical Reports Server (NTRS)

Myers, T. T.; Johnston, D. E.; Mcruer, Duane T.

1987-01-01

Work accomplished under a series of study tasks for the Flying Qualities and Flight Control Systems Design Criteria Experiment (OFQ) of the Shuttle Orbiter Experiments Program (OEX) is summarized. The tasks involved review of applicability of existing flying quality and flight control system specification and criteria for the Shuttle; identification of potentially crucial flying quality deficiencies; dynamic modeling of the Shuttle Orbiter pilot/vehicle system in the terminal flight phases; devising a nonintrusive experimental program for extraction and identification of vehicle dynamics, pilot control strategy, and approach and landing performance metrics, and preparation of an OEX approach to produce a data archive and optimize use of the data to develop flying qualities for future space shuttle craft in general. Analytic modeling of the Orbiter's unconventional closed-loop dynamics in landing, modeling pilot control strategies, verification of vehicle dynamics and pilot control strategy from flight data, review of various existent or proposed aircraft flying quality parameters and criteria in comparison with the unique dynamic characteristics and control aspects of the Shuttle in landing; and finally a summary of conclusions and recommendations for developing flying quality criteria and design guides for future Shuttle craft.

Pheromone-assisted techniques to improve the efficacy of insecticide sprays against Linepithema humile (Hymenoptera: Formicidae).

PubMed

Choe, Dong-Hwan; Tsai, Kasumi; Lopez, Carlos M; Campbell, Kathleen

2014-02-01

Outdoor residual sprays are among the most common methods for targeting pestiferous ants in urban pest management programs. If impervious surfaces such as concrete are treated with these insecticides, the active ingredients can be washed from the surface by rain or irrigation. As a result, residual sprays with fipronil and pyrethroids are found in urban waterways and aquatic sediments. Given the amount of insecticides applied to urban settings for ant control and their possible impact on urban waterways, the development of alternative strategies is critical to decrease the overall amounts of insecticides applied, while still achieving effective control of target ant species. Herein we report a "pheromone-assisted technique" as an economically viable approach to maximize the efficacy of conventional sprays targeting the Argentine ant. By applying insecticide sprays supplemented with an attractive pheromone compound, (Z)-9-hexadecenal, Argentine ants were diverted from nearby trails and nest entrances and subsequently exposed to insecticide residues. Laboratory experiments with fipronil and bifenthrin sprays indicated that the overall kill of the insecticides on Argentine ant colonies was significantly improved (57-142% increase) by incorporating (Z)-9-hexadecenal in the insecticide sprays. This technique, once it is successfully implemented in practical pest management programs, has the potential of providing maximum control efficacy with reduced amount of insecticides applied in the environment.

DDT exposure of frogs: A case study from Limpopo Province, South Africa.

PubMed

Viljoen, Ignatius M; Bornman, Riana; Bouwman, Hindrik

2016-09-01

Amphibians are globally under pressure with environmental contaminants contributing to this. Despite caution aired more than 80 years ago of threats posed to amphibians by DDT spraying for disease vector control, no data have been published on concentrations or effects of DDT contamination in frogs from areas where DDT is actively sprayed to control the insect vectors of malaria. In this study, we sampled fat bodies of Xenopus laevis and Xenopus muelleri naturally occurring in an area where indoor residual spraying of DDT is employed and from adjacent, non-sprayed, areas. ΣDDT concentrations ranged between 

Development of 6-DOF painting robot control system

NASA Astrophysics Data System (ADS)

Huang, Junbiao; Liu, Jianqun; Gao, Weiqiang

2017-01-01

With the development of society, the spraying technology of manufacturing industry in China has changed from the manual operation to the 6-DOF (Degree Of Freedom)robot automatic spraying. Spraying painting robot can not only complete the work which does harm to human being, but also improve the production efficiency and save labor costs. Control system is the most critical part of the 6-DOF robots, however, there is still a lack of relevant technology research in China. It is very necessary to study a kind of control system of 6-DOF spraying painting robots which is easy to operation, and has high efficiency and stable performance. With Googol controller platform, this paper develops programs based on Windows CE embedded systems to control the robot to finish the painting work. Software development is the core of the robot control system, including the direct teaching module, playback module, motion control module, setting module, man-machine interface, alarm module, log module, etc. All the development work of the entire software system has been completed, and it has been verified that the entire software works steady and efficient.

Unit costs for house spraying and bednet impregnation with residual insecticides in Colombia: a management tool for the control of vector-borne disease.

PubMed

Kroeger, A; Ayala, C; Medina Lara, A

2002-06-01

A study of unit costs and cost components of two malaria-control strategies (house spraying and bednet impregnation with residual insecticides) was undertaken in 11 malaria-endemic states (departamentos) of Colombia, using data provided by control staff on self-administered questionnaires. The accuracy of the data was verified by personal visits, telephone conversations and complementary information from 10 other states. Allthe financial-cost components of the malaria-control operations carried out in the previous 6 months and the results of the control operations themselves (including the numbers of houses sprayed and numbers of bednets impregnated/day) were recorded. The information was stratified according to whether the target communities were 'near' or 'far away' from an operational base, the far-away communities being those that needed overnight stays by the control staff. The main variables analysed were unit costs/house treated, and annual cost/person protected. The results show that house spraying was generally more expensive for the health services than bednet impregnation. This is particularly the case in 'nearby' communities, where most of those at-risk live. In such communities, spraying one house was 7.2 times more expensive than impregnating one bednet. Even if only those sleeping under an impregnated net were assumed to be protected, the unit costs/person protected in a 'nearby' community were twice as high for house spraying than for bednet impregnation. In 'nearby' communities, where technicians could return to the operational base each evening, insecticides made up 80% of the total spraying costs and 42% of the costs of bednet impregnation. In 'far-away' communities, however, salaries and 'per diems' were the most important cost components, representing, respectively, 23% and 22% of the costs of spraying, and 34% plus 27% of the costs of impregnation. Insecticide wastage and non-use of discounts on insecticide prices (available through the national Ministry of Health) increased the overall costs considerably. The multiple uses of these cost calculations for district health managers are presented.

Automated MALDI Matrix Coating System for Multiple Tissue Samples for Imaging Mass Spectrometry

NASA Astrophysics Data System (ADS)

Mounfield, William P.; Garrett, Timothy J.

2012-03-01

Uniform matrix deposition on tissue samples for matrix-assisted laser desorption/ionization (MALDI) is key for reproducible analyte ion signals. Current methods often result in nonhomogenous matrix deposition, and take time and effort to produce acceptable ion signals. Here we describe a fully-automated method for matrix deposition using an enclosed spray chamber and spray nozzle for matrix solution delivery. A commercial air-atomizing spray nozzle was modified and combined with solenoid controlled valves and a Programmable Logic Controller (PLC) to control and deliver the matrix solution. A spray chamber was employed to contain the nozzle, sample, and atomized matrix solution stream, and to prevent any interference from outside conditions as well as allow complete control of the sample environment. A gravity cup was filled with MALDI matrix solutions, including DHB in chloroform/methanol (50:50) at concentrations up to 60 mg/mL. Various samples (including rat brain tissue sections) were prepared using two deposition methods (spray chamber, inkjet). A linear ion trap equipped with an intermediate-pressure MALDI source was used for analyses. Optical microscopic examination showed a uniform coating of matrix crystals across the sample. Overall, the mass spectral images gathered from tissues coated using the spray chamber system were of better quality and more reproducible than from tissue specimens prepared by the inkjet deposition method.

Automated MALDI matrix coating system for multiple tissue samples for imaging mass spectrometry.

PubMed

Mounfield, William P; Garrett, Timothy J

2012-03-01

Uniform matrix deposition on tissue samples for matrix-assisted laser desorption/ionization (MALDI) is key for reproducible analyte ion signals. Current methods often result in nonhomogenous matrix deposition, and take time and effort to produce acceptable ion signals. Here we describe a fully-automated method for matrix deposition using an enclosed spray chamber and spray nozzle for matrix solution delivery. A commercial air-atomizing spray nozzle was modified and combined with solenoid controlled valves and a Programmable Logic Controller (PLC) to control and deliver the matrix solution. A spray chamber was employed to contain the nozzle, sample, and atomized matrix solution stream, and to prevent any interference from outside conditions as well as allow complete control of the sample environment. A gravity cup was filled with MALDI matrix solutions, including DHB in chloroform/methanol (50:50) at concentrations up to 60 mg/mL. Various samples (including rat brain tissue sections) were prepared using two deposition methods (spray chamber, inkjet). A linear ion trap equipped with an intermediate-pressure MALDI source was used for analyses. Optical microscopic examination showed a uniform coating of matrix crystals across the sample. Overall, the mass spectral images gathered from tissues coated using the spray chamber system were of better quality and more reproducible than from tissue specimens prepared by the inkjet deposition method.

Macro controlling of copper oxide deposition processes and spray mode by using home-made fully computerized spray pyrolysis system

NASA Astrophysics Data System (ADS)

Essa, Mohammed Sh.; Chiad, Bahaa T.; Shafeeq, Omer Sh.

2017-09-01

Thin Films of Copper Oxide (CuO) absorption layer have been deposited using home-made Fully Computerized Spray Pyrolysis Deposition system FCSPD on glass substrates, at the nozzle to substrate distance equal to 20,35 cm, and computerized spray mode (continues spray, macro-control spray). The substrate temperature has been kept at 450 °c with the optional user can enter temperature tolerance values ± 5 °C. Also that fixed molar concentration of 0.1 M, and 2D platform speed or deposition platform speed of 4mm/s. more than 1000 instruction program code, and specific design of graphical user interface GUI to fully control the deposition process and real-time monitoring and controlling the deposition temperature at every 200 ms. The changing in the temperature has been recorded during deposition processes, in addition to all deposition parameters. The films have been characterized to evaluate the thermal distribution over the X, Y movable hot plate, the structure and optical energy gap, thermal and temperature distribution exhibited a good and uniform distribution over 20 cm2 hot plate area, X-ray diffraction (XRD) measurement revealed that the films are polycrystalline in nature and can be assigned to monoclinic CuO structure. Optical band gap varies from 1.5-1.66 eV depending on deposition parameter.

Where do these bugs come from? Phenotypic structure of Triatoma infestans populations after control interventions in the Argentine Chaco

PubMed Central

Gaspe, María Sol; Provecho, Yael Mariana; Piccinali, Romina Valeria; Gürtler/, Ricardo Esteban

2015-01-01

House re-invasion by native triatomines after insecticide-based control campaigns represents a major threat for Chagas disease vector control. We conducted a longitudinal intervention study in a rural section (Area III, 407 houses) of Pampa del Indio, northeastern Argentina, and used wing geometric morphometry to compare pre-spray and post-spray (re-infestant bugs) Triatoma infestans populations. The community-wide spraying with pyrethroids reduced the prevalence of house infestation by T. infestans from 31.9% to < 1% during a four-year follow-up, unlike our previous studies in the neighbouring Area I. Two groups of bug collection sites differing in wing shape variables before interventions (including 221 adults from 11 domiciles) were used as a reference for assigning 44 post-spray adults. Wing shape variables from post-spray, high-density bug colonies and pre-spray groups were significantly different, suggesting that re-infestant insects had an external origin. Insects from one house differed strongly in wing shape variables from all other specimens. A further comparison between insects from both areas supported the existence of independent re-infestation processes within the same district. These results point to local heterogeneities in house re-infestation dynamics and emphasise the need to expand the geographic coverage of vector surveillance and control operations to the affected region. PMID:25946158

Cutaneous leishmaniasis vector control perspectives using lambdacyhalothrin residual house spraying in El Ingenio, Miranda State, Venezuela.

PubMed

Feliciangeli, M Dora; Mazzarri, Milena B; Campbell-Lendrum, Diarmid; Maroli, Michele; Maingon, Rhaiza

2003-01-01

An indoor vector control trial was carried out between December 1996 and February 1997, with the aim of reducing the population densities of Lutzomyia ovallesi, the proven vector of cutaneous leishmaniasis (CL) in El Ingenio, Miranda State, Venezuela. Houses were matched according to their structure ("bahareque" [mud and straw], concrete, and wood) and randomly assigned to a control group (n = 19) or a treated group (n = 20) that was sprayed with 25 mg/m(2) of lambdacyhalothrin. This dose was selected on the basis of a laboratory susceptibility test of Lu. ovallesi to pyrethroids. Sandfly abundance was measured using CDC light traps 7-79 d post-intervention, by which time the sandfly population in control houses had declined to very low levels, at what was the end of the transmission season. Catches of total females, fed females, and males were significantly lower in sprayed than in control houses immediately after treatment. Catches of total females and males in sprayed houses recovered, reaching the level of control houses after 7 and 11 weeks, respectively. Bioassays following WHO protocols using contact cones on a sandfly laboratory colony showed a short residual effect of the insecticide explaining these results. In contrast, there was no tendency for catches of fed females in the sprayed houses to recover during the course of the trial. Previous studies of adult population dynamics showed a short season of high abundance. Combined with these results, we believe that 2 indoor sprayings with lambdacyhalothrin, the first at the beginning of November and the second at the beginning of January, would considerably reduce the Lu. ovallesi population, and control CL transmission in this and other foci where this sandfly is considered to be the main vector.

Warm spraying-a novel coating process based on high-velocity impact of solid particles.

PubMed

Kuroda, Seiji; Kawakita, Jin; Watanabe, Makoto; Katanoda, Hiroshi

2008-07-01

In recent years, coating processes based on the impact of high-velocity solid particles such as cold spraying and aerosol deposition have been developed and attracting much industrial attention. A novel coating process called 'warm spraying' has been developed, in which coatings are formed by the high-velocity impact of solid powder particles heated to appropriate temperatures below the melting point of the powder material. The advantages of such process are as follows: (1) the critical velocity needed to form a coating can be significantly lowered by heating, (2) the degradation of feedstock powder such as oxidation can be significantly controlled compared with conventional thermal spraying where powder is molten, and (3) various coating structures can be realized from porous to dense ones by controlling the temperature and velocity of the particles. The principles and characteristics of this new process are discussed in light of other existing spray processes such as high-velocity oxy-fuel spraying and cold spraying. The gas dynamics of particle heating and acceleration by the spraying apparatus as well as the high-velocity impact phenomena of powder particles are discussed in detail. Several examples of depositing heat sensitive materials such as titanium, metallic glass, WC-Co cermet and polymers are described with potential industrial applications.

Design and optimal control of on-orbit servicing trajectory for target vehicle in non-coplanar elliptical orbit

NASA Astrophysics Data System (ADS)

Zhou, Wenyong; Yuan, Jianping; Luo, Jianjun

2005-11-01

Autonomous on-orbit servicing provides flexibility to space systems and has great value both in civil and in military. When a satellite performs on-orbit servicing tasks, flying around is the basic type of motion. This paper is concerned with the design and control problems of a chaser satellite flying around a target spacecraft in non-coplanar elliptical orbit for a long time. At first, a mathematical model used to design a long-term flying around trajectory is presented, which is applicable to the situation that the target spacecraft flies in an elliptical orbit. The conditions of the target at the centre of the flying around path are deduced. Considering the safety and task requirements, a long-term flying around trajectory is designed. Taking into account perturbations and navigation errors which can cause the trajectory unstable and mission impossible, a two-impulse control method is put forward. Genetic algorithm is used to minimize the cost function which considers fuel consumption and bias simultaneously. Some simulation works are carried out and the results indicate the flying around mathematical model and the trajectory control method can be used in the design and control of a long-term flying around trajectory.

Spray deposition inside multiple-row nursery trees with a laser-guided sprayer

USDA-ARS?s Scientific Manuscript database

Multiple-row container-grown trees require specially designed sprayers to achieve efficient spray delivery quality. A five-port air-assisted sprayer with both automatic and manual control modes was developed to discharge adequate spray deposition inside multiple-row tree plants. The sprayer resulted...

Characteristics of individual particles in Beijing before, during and after the 2014 APEC meeting

NASA Astrophysics Data System (ADS)

Xu, Zhongjun; Shan, Wei; Qi, Tao; Gao, Jian

2018-05-01

To understand the characteristics of individual aerosol particles as well as the effects of emission control measures on the air quality in Beijing before, during and after the 2014 APEC meeting, aerosol samples collected in Beijing from Oct. 8 to Nov. 24 were investigated by a scanning electron microscopy (SEM) coupled with an energy-dispersive X-ray (EDX). Individual particles were classified into fly ash, ammonium sulfate, carbonaceous particle, tar ball, soot aggregates, Fe/Ti oxide, Ca/Mg carbonate, calcium sulfate and aluminosilicates/quartz. The results showed that PM0.5-1.0 was predominant in aerosol particles while PM2.5-10 was the fewest in aerosol particles. Soot aggregates and carbonaceous particles mainly located in the size range of 0.5-2.5 μm and mineral particles were dominant in the size range of 2.5-10 μm. The tough emission control measures taken by the local government greatly improved the air quality. Reducing vehicles on the roads substantially decreased the amount of soot aggregates, and restricting coal combustion decreased the amount of tar ball during the APEC meeting. The concentrations of carbonaceous and mineral particles abated probably owing to the control on VOCs emission, and water spray and demolition layoff, respectively, during the APEC meeting.

Steering a virtual blowfly: simulation of visual pursuit.

PubMed

Boeddeker, Norbert; Egelhaaf, Martin

2003-09-22

The behavioural repertoire of male flies includes visually guided chasing after moving targets. The visuomotor control system for these pursuits belongs to the fastest found in the animal kingdom. We simulated a virtual fly, to test whether or not experimentally established hypotheses on the underlying control system are sufficient to explain chasing behaviour. Two operating instructions for steering the chasing virtual fly were derived from behavioural experiments: (i) the retinal size of the target controls the fly's forward speed and, thus, indirectly its distance to the target; and (ii) a smooth pursuit system uses the retinal position of the target to regulate the fly's flight direction. Low-pass filters implement neuronal processing time. Treating the virtual fly as a point mass, its kinematics are modelled in consideration of the effects of translatory inertia and air friction. Despite its simplicity, the model shows behaviour similar to that of real flies. Depending on its starting position and orientation as well as on target size and speed, the virtual fly either catches the target or follows it indefinitely without capture. These two behavioural modes of the virtual fly emerge from the control system for flight steering without implementation of an explicit decision maker.

Improving Sterile Insect Technique (SIT) for tsetse flies through research on their symbionts and pathogens

PubMed Central

Abd-Alla, Adly M.M.; Bergoin, Max; Parker, Andrew G.; Maniania, Nguya K.; Vlak, Just M.; Bourtzis, Kostas; Boucias, Drion G.; Aksoy, Serap

2013-01-01

Tsetse flies (Diptera: Glossinidae) are the cyclical vectors of the trypanosomes, which cause human African trypanosomosis (HAT) or sleeping sickness in humans and African animal trypanosomosis (AAT) or nagana in animals. Due to the lack of effective vaccines and inexpensive drugs for HAT, and the development of resistance of the trypanosomes against the available trypanocidal drugs, vector control remains the most efficient strategy for sustainable management of these diseases. Among the control methods used for tsetse flies, Sterile Insect Technique (SIT), in the frame of area-wide integrated pest management (AW-IPM), represents an effective tactic to suppress and/or eradicate tsetse flies. One constraint in implementing SIT is the mass production of target species. Tsetse flies harbor obligate bacterial symbionts and salivary gland hypertrophy virus which modulate the fecundity of the infected flies. In support of the future expansion of the SIT for tsetse fly control, the Joint FAO/IAEA Programme of Nuclear Techniques in Food and Agriculture implemented a six year Coordinated Research Project (CRP) entitled “Improving SIT for Tsetse Flies through Research on their Symbionts and Pathogens”. The consortium focused on the prevalence and the interaction between the bacterial symbionts and the virus, the development of strategies to manage virus infections in tsetse colonies, the use of entomopathogenic fungi to control tsetse flies in combination with SIT, and the development of symbiont-based strategies to control tsetse flies and trypanosomosis. The results of the CRP and the solutions envisaged to alleviate the constraints of the mass rearing of tsetse flies for SIT are presented in this special issue. PMID:22841636

Confusion, knock-down and kill of Aedes aegypti using metofluthrin in domestic settings: a powerful tool to prevent dengue transmission?

PubMed Central

2013-01-01

Background Dengue control methods are reliant upon control of the vector, primarily Aedes aegypti. Current adulticiding methods in North Queensland include treating premises with residual synthetic pyrethroid insecticides (interior residual spraying; IRS), a laborious, intrusive task. The vapor active synthetic pyrethroid metofluthrin might offer an efficient alternative as some studies indicate that it prevents biting and has strong knockdown effects. However, its expellant and/or irritant effects, longevity, residual activity and the speed with which biting behavior is disrupted have not yet been characterized. Methods We exposed cohorts of Cairns colony (F2-4) Ae. aegypti to rooms (17–24 m3) treated with 5% and 10% AI metofluthrin emanators. Using free-flying and caged populations we measured biting (human landing rate), expulsion through unscreened windows, knockdown and death over periods ranging between a few minutes and 24 hrs. Observations of the behavior of single female Ae. aegypti exposed to metofluthrin were also made. Results Female Ae. aegypti exposed to 5% or 10% metofluthrin formulations were almost entirely inhibited from biting. This was the result of rapid knockdown and mortality (80-90% in less than one hour) and to the behavioral impacts of exposure that, within minutes, caused female Ae. aegypti to become disoriented, stop landing on hosts, and seek resting sites. Exposed mosquitoes did not exhibit any increased propensity to exit treated rooms and the 10% AI resin remained fully active for at least 20 days. Conclusion The new, high-dose, resin formulations of metofluthrin act quickly to prevent biting and to knockdown and kill free-flying female Ae. aegypti in our experimental rooms. There was no evidence that metofluthrin induced escape from treated areas. Resin-based metofluthrin emanators show great potential as a replacement for labor intensive IRS for dengue vector control. PMID:24025232

Effects of pyriproxifen on wild populations of the house fly, Musca domestica, and compatibility with its principal parasitoids.

USDA-ARS?s Scientific Manuscript database

Background. The house fly, Musca domestica L., is an important pest of animal agriculture. Effective fly management requires integration of manure management, mass trapping, biological control, and selective insecticide use. Insecticidal control of house flies is difficult due to the rapidity of res...

Use of pupal parasitoids as biological control agents of filth flies on equine facilities

USDA-ARS?s Scientific Manuscript database

House flies, Musca domestica L., and stable flies, Stomoxys calcitrans (L.), (Diptera: Muscidae), are common pests on horse farms. The use of pupal parasitoids as biological control agents for filth flies is becoming more popular on equine facilities; however, there is a lack of information on the e...

Color deviation controlling of phosphor conformal coating by advanced spray painting technology for white LEDs.

PubMed

Yang, Liang; Wang, Simin; Lv, Zhicheng; Liu, Sheng

2013-04-01

An advanced phosphor conformal coating technology is proposed, good correlated color temperature (CCT) and chromaticity uniformity samples are fabricated through phosphor spray painting technology. Spray painting technology is also suitable for phosphor conformal coating of whole LED wafers. The samples of different CCTs are obtained through controlling the phosphor film thickness in the range of 6-80 μm; CCT variation of samples can be controlled in the range of ±200 K. The experimental Δuv reveals that the spray painting method can obtain a much smaller CCT variation (Δuv of 1.36e(-3)) than the conventional dispensing method (Δuv of 11.86e(-3)) when the light is emitted at angles from -90° to +90°, and chromaticity area uniformity is also improved significantly.

A report on the indoor residual spraying (IRS) in the control of Phlebotomus argentipes, the vector of visceral leishmaniasis in Bihar (India): an initiative towards total elimination targeting 2015 (Series-1).

PubMed

Kumar, V; Kesari, S; Dinesh, D S; Tiwari, A K; Kumar, A J; Kumar, R; Singh, V P; Das, P

2009-09-01

Visceral leishmaniasis, commonly known as kala-azar is endemic in Bihar state, India. Current vector control programme in Bihar focuses mainly on spraying the sandfly infested dwellings with DDT. The Government of India in collaboration with WHO has fixed the target 2015 for total elimination of kala-azar. The present study was carried out to see the impact of DDT and improved IEC in the containment of vector density vis-à-vis disease transmission. Before the start of the spraying operations training was imparted to all the medical and paramedical personnel regarding the methods of spraying operations. Pre- and post-sandfly density was monitored in four selected districts. Incidences of kala-azar cases were compared for pre- and post-spray periods. Social acceptability and perceptions of households was collected through questionnaires from 500 randomly selected households in the study districts. House index in three study districts reduced considerably during post-spray when compared to pre-spray. Kala-azar incidence in many districts was reduced after the DDT spray. Either partial or complete refusal was reported in 14.4%, while 35% were not satisfied with the suspension concentration and coverage; and 46.6% were found satisfied with the spraying procedure. Strengthening the IEC activities to sensitise the community, proper training of health personnel, monitoring of spray, good surveillance, proper treatment of cases and two rounds of DDT spray with good coverage in the endemic districts up to three years are essential to achieve the desired total elimination of kala-azar in Bihar state.

The effects of sea spray and atmosphere-wave coupling on air-sea exchange during a tropical cyclone

NASA Astrophysics Data System (ADS)

Garg, Nikhil; Kwee Ng, Eddie Yin; Narasimalu, Srikanth

2018-04-01

The study investigates the role of the air-sea interface using numerical simulations of Hurricane Arthur (2014) in the Atlantic. More specifically, the present study aims to discern the role ocean surface waves and sea spray play in modulating the intensity and structure of a tropical cyclone (TC). To investigate the effects of ocean surface waves and sea spray, numerical simulations were carried out using a coupled atmosphere-wave model, whereby a sea spray microphysical model was incorporated within the coupled model. Furthermore, this study also explores how sea spray generation can be modelled using wave energy dissipation due to whitecaps; whitecaps are considered as the primary mode of spray droplets generation at hurricane intensity wind speeds. Three different numerical simulations including the sea- state-dependent momentum flux, the sea-spray-mediated heat flux, and a combination of the former two processes with the sea-spray-mediated momentum flux were conducted. The foregoing numerical simulations were evaluated against the National Data Buoy Center (NDBC) buoy and satellite altimeter measurements as well as a control simulation using an uncoupled atmosphere model. The results indicate that the model simulations were able to capture the storm track and intensity: the surface wave coupling results in a stronger TC. Moreover, it is also noted that when only spray-mediated heat fluxes are applied in conjunction with the sea-state-dependent momentum flux, they result in a slightly weaker TC, albeit stronger compared to the control simulation. However, when a spray-mediated momentum flux is applied together with spray heat fluxes, it results in a comparably stronger TC. The results presented here allude to the role surface friction plays in the intensification of a TC.

Spray Characterization of Ultra-Low-Volume Sprayers Typically Used in Vector Control

DTIC Science & Technology

2009-01-01

Standard test method for determining liquid drop size characteristics in a spray using optical nonimaging light-scattering instruments. An- nual book of...cloud was directed through the optical path of the laser varied between sprayers, depending on the width of the spray 1 Mention of a trademark

Cold Spray Technology for Repair of Magnesium Rotorcraft Components (Briefing Charts)

DTIC Science & Technology

2007-01-01

control valve Nozzle Braided flex hose Helium Tank Powder Feeder Spray Nozzle ARL Portable System Parameters for Applying CP-Al to ZE41A - Mg...and Advantages of Cold Spray •Present Test Results to Date •Coating Integrity and Microstructural Analysis •Adhesion, Hardness and Corrosion Tests

Development of Air Force aerial spray night operations: High altitude swath characterization

USDA-ARS?s Scientific Manuscript database

Multiple trials were conducted from 2006 to 2014 in an attempt to validate aerial spray efficacy at altitudes conducive to night spray operations using night vision goggles (NVG). Higher altitude application of pesticide (>400 feet above ground level [AGL]) suggested that effective vector control mi...

Predicting fruit fly's sensing rate with insect flight simulations.

PubMed

Chang, Song; Wang, Z Jane

2014-08-05

Without sensory feedback, flies cannot fly. Exactly how various feedback controls work in insects is a complex puzzle to solve. What do insects measure to stabilize their flight? How often and how fast must insects adjust their wings to remain stable? To gain insights into algorithms used by insects to control their dynamic instability, we develop a simulation tool to study free flight. To stabilize flight, we construct a control algorithm that modulates wing motion based on discrete measurements of the body-pitch orientation. Our simulations give theoretical bounds on both the sensing rate and the delay time between sensing and actuation. Interpreting our findings together with experimental results on fruit flies' reaction time and sensory motor reflexes, we conjecture that fruit flies sense their kinematic states every wing beat to stabilize their flight. We further propose a candidate for such a control involving the fly's haltere and first basalar motor neuron. Although we focus on fruit flies as a case study, the framework for our simulation and discrete control algorithms is applicable to studies of both natural and man-made fliers.

NASA Tech Briefs, August 2009

NASA Technical Reports Server (NTRS)

2009-01-01

Topics covered include: Aligning a Receiving Antenna Array to Reduce Interference; Collecting Ground Samples for Balloon-Borne Instruments; Tethered Pyrotechnic Apparatus for Acquiring a Ground Sample; Enhanced Video-Oculography System; Joint Carrier-Phase Synchronization and LDPC Decoding; Dual-Polarization, Sideband-Separating, Balanced Receiver for 1.5 THz Modular Battery Charge Controller; Efficient Multiplexer FPGA Block Structures Based on G4FETs; VLSI Microsystem for Rapid Bioinformatic Pattern Recognition; Low-Noise Amplifier for 100 to 180 GHz; Improved Fabrication of Ceramic Matrix Composite/Foam Core Integrated Structures; Inert Welding/Brazing Gas Filters and Dryers; Fabricating Copper Nanotubes by Electrodeposition; Reducing Aerodynamic Drag on Empty Open Cargo Vehicles; Rotary Percussive Auto-Gopher for Deep Drilling and Sampling; More About Reconfigurable Exploratory Robotic Vehicles; Thermostatic Valves Containing Silicone-Oil Actuators; Improving Heat Flux Performance of Flat Surface in Spray-Cooling Systems; Treating Fibrous Insulation to Reduce Thermal Conductivity; Silica-Aerogel Composites Opacified with La(sub0.7)Sr(sub0.3)MnO3; Cyclic Oxidation Behavior of CuCrAl Cold-Sprayed Coatings for Reusable Launch Vehicles; Ceramic Fiber Structures for Cryogenic Load-Bearing Applications; Elastomer Reinforced with Carbon Nanotubes; Biologically Inspired Purification and Dispersion of SWCNTs; A Technique for Adjusting Eigenfrequencies of WGM Resonators; Low-Pressure, Field-Ionizing Mass Spectrometer; Modifying Operating Cycles to Increase Stability in a LITS; Chamber for Simulating Martian and Terrestrial Environments; Algorithm for Detecting a Bright Spot in an Image; Extreme Programming: Maestro Style; Adaptive Behavior for Mobile Robots; Protocol for Communication Networking for Formation Flying; Planning Complex Sequences Using Compressed Representations; and Self-Supervised Learning of Terrain Traversability from Proprioceptive Sensors.

Controlling Flows Of Two Ingredients For Spraying

NASA Technical Reports Server (NTRS)

Chandler, Huel H.

1995-01-01

Closed-loop servo control subsystem incorporated, as modification, into system controlling flows of two ingredients mixed and sprayed to form thermally insulating foams on large tanks. Provides steady flows at specified rates. Foams produced smoother and of higher quality. Continued use of system results in substantial reduction in cost stemming from close control of application of foam and consequent reduced use of material.

Combination of Trichoderma harzianum endochitinase and a membrane-affecting fungicide on control of Alternaria leaf spot in transgenic broccoli plants.

PubMed

Mora, A; Earle, E D

2001-04-01

Progeny from transgenic broccoli (cv. Green Comet) expressing a Trichoderma harzianum endochitinase gene were used to assess the interaction between endochitinase and the fungicide Bayleton in the control of Alternaria brassicicola. In vitro assays have shown synergistic effects of endochitinase and fungicides on fungal pathogens. Our study examined the in planta effects of endochitinase and Bayleton, individually and in combination. Two month old transgenic and non-transgenic plants were sprayed with ED50 levels of Bayleton and/or inoculated with an A. brassicicola spore suspension. Disease levels in non-sprayed transgenic plants were not statistically different from sprayed transgenic plants nor from sprayed non-transgenic controls. Thus endochitinase-transgenic plants alone provided a significant reduction of disease severity, comparable to the protection by fungicide on non-transgenic plants. Comparison of the expected additive and observed effects revealed no synergism between endochitinase and Bayleton (at ED50 level), and usually less than an additive effect. Some transgenic lines sprayed with fungicide at doses higher than ED50 showed resistance similar to the non-sprayed transgenic lines, again suggesting no synergistic effect. Lack of synergism may be due to incomplete digestion of the cell wall by endochitinase, so that the effect of Bayleton at the cell membrane is not enhanced.

Spray combustion experiments and numerical predictions

NASA Technical Reports Server (NTRS)

Mularz, Edward J.; Bulzan, Daniel L.; Chen, Kuo-Huey

1993-01-01

The next generation of commercial aircraft will include turbofan engines with performance significantly better than those in the current fleet. Control of particulate and gaseous emissions will also be an integral part of the engine design criteria. These performance and emission requirements present a technical challenge for the combustor: control of the fuel and air mixing and control of the local stoichiometry will have to be maintained much more rigorously than with combustors in current production. A better understanding of the flow physics of liquid fuel spray combustion is necessary. This paper describes recent experiments on spray combustion where detailed measurements of the spray characteristics were made, including local drop-size distributions and velocities. Also, an advanced combustor CFD code has been under development and predictions from this code are compared with experimental results. Studies such as these will provide information to the advanced combustor designer on fuel spray quality and mixing effectiveness. Validation of new fast, robust, and efficient CFD codes will also enable the combustor designer to use them as additional design tools for optimization of combustor concepts for the next generation of aircraft engines.

Efficacy of Insecticide and Bioinsecticide Ground Sprays to Control Metisa plana Walker (Lepidoptera: Psychidae) in Oil Palm Plantations, Malaysia.

PubMed

Salim, Hasber; Rawi, Che Salmah Md; Ahmad, Abu Hassan; Al-Shami, Salman Abdo

2015-12-01

The effectiveness of the synthetic insecticides trichlorfon, lambda-cyhalothrin, cypermethrin emulsion concentrated (EC) and cypermethrin emulsion water based (EW) and a bio-insecticide, Bacillus thuringiensis subsp. kurstaki (Btk), was evaluated at 3, 7, 14 and 30 days after treatment (DAT) for the control of Metisa plana larvae in an oil palm (Elaeis guineensis) plantation in Malaysia. Although all synthetic insecticides effectively reduced the larval population of M. plana, trichlorfon, lambda-cyhalothrin and cypermethrin EC were the fastest-acting. The larval population dropped below the economic threshold level (ETL) 30 days after a single application of the synthetic insecticides. Application of Btk, however, gave poor results, with the larval population remaining above the ETL post treatment. In terms of operational productivity, ground spraying using power spray equipment was time-consuming and resulted in poor coverage. Power spraying may not be appropriate for controlling M. plana infestations in large fields. Using a power sprayer, one man could cover 2-3 ha per day. Hence, power spraying is recommended during outbreaks of infestation in areas smaller than 50 ha.

Efficacy of Insecticide and Bioinsecticide Ground Sprays to Control Metisa plana Walker (Lepidoptera: Psychidae) in Oil Palm Plantations, Malaysia

PubMed Central

Salim, Hasber; Rawi, Che Salmah Md.; Ahmad, Abu Hassan; Al-Shami, Salman Abdo

2015-01-01

The effectiveness of the synthetic insecticides trichlorfon, lambda-cyhalothrin, cypermethrin emulsion concentrated (EC) and cypermethrin emulsion water based (EW) and a bio-insecticide, Bacillus thuringiensis subsp. kurstaki (Btk), was evaluated at 3, 7, 14 and 30 days after treatment (DAT) for the control of Metisa plana larvae in an oil palm (Elaeis guineensis) plantation in Malaysia. Although all synthetic insecticides effectively reduced the larval population of M. plana, trichlorfon, lambda-cyhalothrin and cypermethrin EC were the fastest-acting. The larval population dropped below the economic threshold level (ETL) 30 days after a single application of the synthetic insecticides. Application of Btk, however, gave poor results, with the larval population remaining above the ETL post treatment. In terms of operational productivity, ground spraying using power spray equipment was time-consuming and resulted in poor coverage. Power spraying may not be appropriate for controlling M. plana infestations in large fields. Using a power sprayer, one man could cover 2–3 ha per day. Hence, power spraying is recommended during outbreaks of infestation in areas smaller than 50 ha. PMID:26868711

Biology and control of tabanids, stable flies and horn flies.

PubMed

Foil, L D; Hogsette, J A

1994-12-01

Tabanids are among the most free-living adult flies which play a role as livestock pests. A single blood meal is used as a source of energy for egg production (100-1,000 eggs per meal), and females of certain species can oviposit before a blood meal is obtained (autogeny). Therefore, the maintenance of annual populations requires successful oviposition by only 2% of females. Wild animal blood sources are usually available to maintain annual tabanid populations. Larval habitats are also independent of domestic livestock. Thus, the use of repellents or partial repellents is the only effective chemical strategy to reduce the incidence of tabanids on livestock. Permanent traps (and possibly treated silhouette traps) can be employed to intercept flies. Selective grazing or confinement can also reduce the impact of tabanids. Stable fly adults are dependent on vertebrate blood for survival and reproduction, but the amount of time spent in contact with the host is relatively small. Stable fly larvae develop in manure, spilled feed and decaying vegetation. Management of larval habitats by sanitation is the key to stable fly control. Treatment of animals with residual insecticides can aid in control; thorough application to the lower body parts of livestock is important. Proper use of modified traps, using either treated targets or solar-powered electrocution grids, can be effective in reducing stable fly populations. Adult horn flies spend the major part of their time on the host, and the larvae are confined to bovid manure. Therefore, almost any form of topical insecticide application for livestock is effective against horn flies, in the absence of insecticide resistance. Treatments should be applied when economic benefit is possible; economic gains are associated with increased weaning weights and weight gains of yearling and growing cattle. Oral chemical treatments (insect growth regulators or insecticides) administered at appropriate rates via bolus, water, food or mineral mixtures can inhibit horn fly larval development. However, adult horn fly movement among cattle herds limits the use of larval control for horn fly population management. The augmentation of native parasites, predators and competitors has been attempted and even promoted for horn fly and stable fly control, but evidence for the success of such programmes is equivocal.

House fly management with viral and botanical agents

USDA-ARS?s Scientific Manuscript database

House flies are major pests of human and animal health throughout the world and are among the most difficult to control because of resistance to every insecticide that has been developed for their control. A promising microbial agent for fly control is salivary gland hypertrophy virus (MdSGHV), a m...

A Simulation Study on Take-Off and Landing Dynamics of the Aircraft of a Fly-By-Wire Control System

DTIC Science & Technology

1993-01-07

L:V,"DIN G DYN;AMICS OF THE AIRCRAFT OF A FLY-BY-WIRE CONTROL SYSTEM by Y achang Feng, Gang Chert, Peiqiong Li 93-00985 Distribution unlimit ed. FASTC...FLY-BY-WIRE CONTROL SYSTEM By: Yachang Feng, Gang Chen, Peiqiong- Li English pages: 17 Source: Hangkon, Xuebao, Vol. 12, No. 6, June, 1991; pp. 252-258...Landing Dynamics of the Aircraft of a Fly-By-Wire Control System Beijing University of Aeronautics and Astronautics Yachang FENG, Gang CHEN and Peiqiong Li

A Three-Year Field Validation Study to Improve the Integrated Pest Management of Hot Pepper

PubMed Central

Kim, Ji-Hoon; Yun, Sung-Chul

2013-01-01

To improve the integrated pest management (IPM) of hot pepper, field study was conducted in Hwasung from 2010 to 2012 and an IPM system was developed to help growers decide when to apply pesticides to control anthracnose, tobacco budworm, Phytophthora blight, bacterial wilt, and bacterial leaf spot. The three field treatments consisted of IPM sprays following the forecast model advisory, a periodic spray at 7-to-10-day intervals, and no spray (control). The number of annual pesticide applications for the IPM treatment ranged from six to eight, whereas the plots subjected to the periodic treatment received pesticide 11 or 12 times annually for three years. Compared to the former strategy, our improved IPM strategy features more intense pest management, with frequent spraying for anthracnose and mixed spraying for tobacco budworm or Phytophthora blight. The incidences for no pesticide control in 2010, 2011, and 2012 were 91, 97.6, and 41.4%, respectively. Conversely, the incidences for the IPM treatment for those years were 7.6, 62.6, and 2%, and the yields from IPM-treated plots were 48.6 kg, 12.1 kg, and 48.8 kg. The incidence and yield in the IPM-treated plots were almost the same as those of the periodic treatment except in 2011, in which no unnecessary sprays were given, meaning that the IPM control was quite successful. From reviewing eight years of field work, sophisticated forecasts that optimize pesticide spray timing reveal that reliance on pesticides can be reduced without compromising yield. Eco-friendly strategies can be implemented in the pest management of hot pepper. PMID:25288956

FLIT-MLO and No. 2 fuel oil: Effects of aerosol applications to mallard eggs on hatchability and behavior of ducklings

USGS Publications Warehouse

Albers, P.H.; Heinz, G.H.

1983-01-01

FLIT-MLO and No. 2 fuel oil are sprayed on wetlands for mosquito control during spring and summer. In one experiment to assess the effects of the spraying on birds, mallard eggs were sprayed with amounts of No. 2 fuel oil equivalent to 2.34, 4.67, or 18.70 liters/ha or FLIT-MLO equivalent to 9.35, 46.75, or 140.25 liters/ha on Day 6 of incubation. In a second experiment, mallard eggs were sprayed with 9.35, 46.75, or 140.25 liters/ha of FLIT-MLO on Days 3, 6, 12, or 18 of incubation. Hatchability of eggs sprayed with the highest treatment level of each substance was significantly lower than that of controls for the first experiment. Hatchability of eggs sprayed with FLIT-MLO in the second experiment was never significantly lower than that of controls. Ducklings from the first experiment, 36-48 hr old, were cold stressed for 1 hr at 8 degrees C and then immediately tested for their ability to respond to a fright stimulus. Ducklings from the group of eggs sprayed with 140.25 liters/ha of FLIT-MLO ran a significantly shorter distance from the fright stimulus than did controls. The effects of the heaviest exposure to FLIT-MLO (140.25 liters/ha) on egg hatchability and behavior of newly hatched young are uncertain because of the contradictory results for hatching success in the two experiments. However, normal applications of FLIT-MLO (9.35-46.75 liters/ha) or No. 2 fuel oil (2.34-4.67 liters/ha) do not appear to pose a threat to the embryos of breeding birds.

The utility of microsatellite DNA markers for the evaluation of area-wide integrated pest management using SIT for the fruit fly, Bactrocera dorsalis (Hendel), control programs in Thailand.

PubMed

Aketarawong, Nidchaya; Chinvinijkul, Suksom; Orankanok, Watchreeporn; Guglielmino, Carmela Rosalba; Franz, Gerald; Malacrida, Anna Rodolfa; Thanaphum, Sujinda

2011-01-01

The oriental fruit fly, Bactrocera dorsalis (Hendel), is a key pest that causes reduction of the crop yield within the international fruit market. Fruit flies have been suppressed by two Area-Wide Integrated Pest Management programs in Thailand using Sterile Insect Technique (AW-IPM-SIT) since the late 1980s and the early 2000s. The projects' planning and evaluation usually rely on information from pest status, distribution, and fruit infestation. However, the collected data sometimes does not provide enough detail to answer management queries and public concerns, such as the long term sterilization efficacy of the released fruit fly, skepticism about insect migration or gene flow across the buffer zone, and the re-colonisation possibility of the fruit fly population within the core area. Established microsatellite DNA markers were used to generate population genetic data for the analysis of the fruit fly sampling from several control areas, and non-target areas, as well as the mass-rearing facility. The results suggested limited gene flow (m < 0.100) across the buffer zones between the flies in the control areas and flies captured outside. In addition, no genetic admixture was revealed from the mass-reared colony flies from the flies within the control area, which supports the effectiveness of SIT. The control pests were suppressed to low density and showed weak bottleneck footprints although they still acquired a high degree of genetic variation. Potential pest resurgence from fragmented micro-habitats in mixed fruit orchards rather than pest incursion across the buffer zone has been proposed. Therefore, a suitable pest control effort, such as the SIT program, should concentrate on the hidden refuges within the target area.

Vision-aided Monitoring and Control of Thermal Spray, Spray Forming, and Welding Processes

NASA Technical Reports Server (NTRS)

Agapakis, John E.; Bolstad, Jon

1993-01-01

Vision is one of the most powerful forms of non-contact sensing for monitoring and control of manufacturing processes. However, processes involving an arc plasma or flame such as welding or thermal spraying pose particularly challenging problems to conventional vision sensing and processing techniques. The arc or plasma is not typically limited to a single spectral region and thus cannot be easily filtered out optically. This paper presents an innovative vision sensing system that uses intense stroboscopic illumination to overpower the arc light and produce a video image that is free of arc light or glare and dedicated image processing and analysis schemes that can enhance the video images or extract features of interest and produce quantitative process measures which can be used for process monitoring and control. Results of two SBIR programs sponsored by NASA and DOE and focusing on the application of this innovative vision sensing and processing technology to thermal spraying and welding process monitoring and control are discussed.

Apparatus and method to control atmospheric water vapor composition and concentration during dynamic cooling of biological tissues in conjunction with laser irradiations

DOEpatents

Nelson, J. Stuart; Anvari, Bahman; Tanenbaum, B. Samuel; Milner, Thomas E.

1999-01-01

Cryogen spray cooling of skin surface with millisecond cryogen spurts is an effective method for establishing a controlled temperature distribution in tissue and protecting the epidermis from nonspecific thermal injury during laser mediated dermatological procedures. Control of humidity level, spraying distance and cryogen boiling point is material to the resulting surface temperature. Decreasing the ambient humidity level results in less ice formation on the skin surface without altering the surface temperature during the cryogen spurt. For a particular delivery nozzle, increasing the spraying distance to 85 millimeters lowers the surface temperature. The methodology comprises establishing a controlled humidity level in the theater of operation of the irradiation site of the biological tissues before and/or during the cryogenic spray cooling of the biological tissue. At cold temperatures calibration was achieved by mounting a thermistor on a thermoelectric cooler. The thermal electric cooler was cooled from from 20.degree. C. to about -20.degree. C. while measuring its infrared emission.

A New Classification System for the Actions of IRS Chemicals Traditionally Used for Malaria Control

DTIC Science & Technology

2007-08-08

compounds for IRS use that elicit a spatial repellent response. Insecticides recommended for indoor residual spraying (IRS) continue to be evaluated...hundred mosquitoes would enter a house, bite while indoors , and escape and survive if the house were not sprayed . We can use our proportions, described...considered to be the cheapest and most effective chemical for use in house spray operations. Its long residual action when sprayed on inner walls further

[Dexpanthenol nasal spray as an effective therapeutic principle for treatment of rhinitis sicca anterior].

PubMed

Kehrl, W; Sonnemann, U

1998-09-01

Controlled clinical studies on medical treatment of rhinitis sicca anterior have not yet been published. Therapy recommendations are based on experiences but not on results of controlled clinical studies. The aim of this study was to examine the efficacy and tolerance of a new form of application of Dexpanthenol in physiologic saline solution (Nasicur). A randomized comparison of parallel groups was performed. One group was treated with the nasal spray while the control group received a placebo. The assessment of nasal breathing resistance and the extent of crust formation according to scores were defined as target parameters. Statistical analysis was carried out according to Wilcoxon at alpha < or = 0.05. Forty-eight outpatients diagnosed with rhinitis sicca anterior were included in this study. Twenty-four received the medication, and 29 were treated with a placebo. The superiority of the dexpanthenol nasal spray in comparison to the placebo medication was demonstrated for both target parameters as clinically relevant and statistically significant. The placebo spray showed clinical improvement of the other treatment outcome parameters. Dexpanthenol nasal spray showed no statistically significant difference in comparison to placebo. The clinically proven efficacy is emphasized by good tolerance of both treatments which was validated by the objective rhinoscopy findings. Good compliance was confirmed. The result of the controlled clinical study confirms that the dexpanthenol nasal spray is an effective medicinal treatment of rhinitis sicca anterior and is more effective than common medications.

Effects on wildlife of DDT used for control of Dutch elm disease

USGS Publications Warehouse

Benton, A.H.

1951-01-01

During the summer of 1949 studies were conducted at Princeton, New Jersey, to determine the effects on wildlife of DDT used in the control of Dutch elm disease. Direct mortality was determined by intensive search for dead birds after spraying. Twenty-six songbirds, one bat, and one gray squirrel were found. Of 11 dead birds from a study area of approximately 20 acres only one was an adult. Songbird populations were determined by censuses before and after spraying on a study area and on a similar unsprayed check area. The number of all breeding birds showed a 19.6 percent decrease on both the study and check areas during the week immediately following spraying. About two weeks after spraying the population in the treated area began to increase and within another week was back to prespray level. When only those species common to both sprayed and unsprayed areas are considered a population decline of 22 percent was measured in the sprayed area while the check area showed a 6 percent increase in numbers over the same period. Nestling mortality was studied in both areas. Among 18 young found on the study area during and following spraying 8 (44%) survived. Death of two broods of catbirds occurred four days after spraying. Of 21 young found on the check area 15 (71%) survived.

Effects of Nantucket pine tip moth insecticide spray schedules on loblolly pine seedlings

Treesearch

Christopher J. Fettig; Kenneth W. McCravy; C. Wayne Berisford

2000-01-01

Frequent and prolonged insecticide applications to control the Nantucket pine tip moth, Rhyacionia frustrana (Comstock) (Lepidoptera:Torticidae) (NPTM), although effective, may be impractical and uneconomica1, for commercial timber production. Timed insecticide sprays of permethrin (Polmce 3.2® EC) were applied to all possible combinations of spray...

Effectiveness of agricultural oils alongside fungicides in the late dormant treatment for suppression of peach scab in Georgia, 2016

USDA-ARS?s Scientific Manuscript database

The efficacy of different fungicide applications for control of peach scab was tested on cv Flameprince. The fungicidal applications were applied with an airblast sprayer with a spray volume of 100 gal/A. Control treatment regimens included a non-treated control, a standard fungicidal spray program ...

Production of morphology-controllable porous hyaluronic acid particles using a spray-drying method.

PubMed

Iskandar, Ferry; Nandiyanto, Asep Bayu Dani; Widiyastuti, W; Young, Lee Sin; Okuyama, Kikuo; Gradon, Leon

2009-05-01

Hyaluronic acid (HA) porous particles with controllable porosity and pore size, ranging from 100 to 300 nm, were successfully prepared using a colloidal templating and spray-drying method. HA powder and polystyrene latex (PSL) particles, which were used as the precursor and templating agent, respectively, were mixed in aqueous solution and spray-dried using a two-fluid nozzle system to produce HA and PSL composite particles. Water was evaporated during spray-drying using heated air with a temperature of 120 degrees C. This simple process was completed within several seconds. The prepared particles were collected and washed with an organic solvent to dissolve the PSL templating agent. The porosity and pore size of the resulting particles were easily controlled by changing the initial mass ratio of precursor to templating agent, i.e., HA to PSL, and by altering the size of the PSL template particles.

Evaluation of the efficacy of lambda-cyhalothrin applied as ultra-low volume and thermal fog for emergency control of Aedes aegypti in Honduras.

PubMed

Perich, M J; Sherman, C; Burge, R; Gill, E; Quintana, M; Wirtz, R A

2001-12-01

An extended-duration formulation of lambda-cyhalothrin (Demand CS) applied as either an ultra-low volume (ULV) or thermal fog spray from a new handheld sprayer (Terrier) against Aedes aegypti was evaluated in Honduras. Spray applications were made at the front door for 1 min or to each room for 15 sec, both for the ULV and thermal fog applications to houses in separate blocks for each treatment. The efficacy and duration of effectiveness of the spray was determined from sentinel caged mosquito mortality and collection of mosquitoes within houses with a backpack power aspirator. Sentinel caged mosquito mortality in both open and sequestered locations was 97-100% for all spray treatments, with control mortality less than 2%. Both ULV applications (front door and each room) provided 4 wk of significant control (P < 0.01) based on adult Ae. aegypti house collections.

Distribution and Dispersal of Phlebotomus papatasi (Diptera: Psychodidae) in a Zoonotic Cutaneous Leishmaniasis Focus, the Northern Negev, Israel

PubMed Central

Orshan, Laor; Elbaz, Shirly; Ben-Ari, Yossi; Akad, Fouad; Afik, Ohad; Ben-Avi, Ira; Dias, Debora; Ish-Shalom, Dan; Studentsky, Liora; Zonstein, Irina

2016-01-01

Background Zoonotic cutaneous leishmaniasis has long been endemic in Israel. In recent years reported incidence of cutaneous leishmaniasis increased and endemic transmission is being observed in a growing number of communities in regions previously considered free of the disease. Here we report the results of an intensive sand fly study carried out in a new endemic focus of Leishmania major. The main objective was to establish a method and to generate a data set to determine the exposure risk, sand fly populations' dynamics and evaluate the efficacy of an attempt to create "cordon sanitaire" devoid of active jird burrows around the residential area. Methodology/Principal Findings Sand flies were trapped in three fixed reference sites and an additional 52 varying sites. To mark sand flies in the field, sugar solutions containing different food dyes were sprayed on vegetation in five sites. The catch was counted, identified, Leishmania DNA was detected in pooled female samples and the presence of marked specimens was noted. Phlebotomus papatasi, the vector of L. major in the region was the sole Phlebotomus species in the catch. Leishmania major DNA was detected in ~10% of the pooled samples and the highest risk of transmission was in September. Only a few specimens were collected in the residential area while sand fly numbers often exceeded 1,000 per catch in the agricultural fields. The maximal travel distance recorded was 1.91km for females and 1.51km for males. The calculated mean distance traveled (MDT) was 0.75km. Conclusions The overall results indicate the presence of dense and mobile sand fly populations in the study area. There seem to be numerous scattered sand fly microsites suitable for development and resting in the agricultural fields. Sand flies apparently moved in all directions, and reached the residential area from the surrounding agricultural fields. The travel distance noted in the current work, supported previous findings that P. papatasi like P. ariasi, can have a relatively long flight range and does not always stay near breeding sites. Following the results, the width of the "cordon sanitaire" in which actions against the reservoir rodents were planned, was extended into the depth of the agricultural fields. PMID:27427959

Methylmercury Exposure Induces Sexual Dysfunction in Male and Female Drosophila Melanogaster.

PubMed

Chauhan, Ved; Srikumar, Syian; Aamer, Sarah; Pandareesh, Mirazkar D; Chauhan, Abha

2017-09-24

Mercury, an environmental health hazard, is a neurotoxic heavy metal. In this study, the effect of methylmercury (MeHg) exposure was analyzed on sexual behavior in Drosophila melanogaster (fruit fly), because neurons play a vital role in sexual functions. The virgin male and female flies were fed a diet mixed with different concentrations of MeHg (28.25, 56.5, 113, 226, and 339 µM) for four days, and the effect of MeHg on copulation of these flies was studied. While male and female control flies (no MeHg) and flies fed with lower concentrations of MeHg (28.25, 56.5 µM) copulated in a normal manner, male and female flies exposed to higher concentrations of MeHg (113, 226, and 339 µM) did not copulate. When male flies exposed to higher concentrations of MeHg were allowed to copulate with control female flies, only male flies fed with 113 µM MeHg were able to copulate. On the other hand, when female flies exposed to higher concentrations of MeHg were allowed to copulate with control male flies, none of the flies could copulate. After introduction of male and female flies in the copulation chamber, duration of wing flapping by male flies decreased in a MeHg-concentration-dependent manner from 101 ± 24 seconds (control) to 100.7 ± 18, 96 ±12, 59 ± 44, 31 ± 15, and 3.7 ± 2.7 seconds at 28.25, 56.5, 113, 226, and 339 µM MeHg, respectively. On the other hand, grooming in male and female flies increased in a MeHg-concentration-dependent manner. These findings suggest that MeHg exposure causes sexual dysfunction in male and female Drosophila melanogaster . Further studies showed that MeHg exposure increased oxidative stress and decreased triglyceride levels in a concentration-dependent manner in both male and female flies, suggesting that MeHg-induced oxidative stress and decreased triglyceride levels may partly contribute to sexual dysfunction in fruit flies.

Development and Testing of a Mobile Platform for Tank Remediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nance, T.A.

2001-01-16

The Department of Energy (DOE) is committed to removing millions of gallons of high level radioactive waste from waste storage tanks at the Savannah River Site (SRS). SRS was the first site in the DOE complex to have emptied and closed high level waste tanks. Tank closure at the Site is now progressing to tanks containing waste composed of liquid and large deposits of solids, including a tank that has a potential ''heel''. A heel is a hardened mass of solid waste material spread across the tank bottom. Tank closure requires breaking up this heel and moving the material tomore » the intake of a pumping system for transfer from the tank. In the past, overhead spray systems have been used with some success at moving waste. But the limited number of risers restricts the coverage area of the overhead spray system. Therefore, a floor- level spray system will be used to separate manageable size chunks of the material from the heel. The chunks will be guided into the pump's intake to be remove from the tank. The floor-level spray system movement will be accomplished by using a mobile platform, a crawler, which provides transport to nearly every point on the tank floor. Transport of the spray system will allow the system to ''corral'' the waste away from the tank walls and control the movement of the material across the tank floor. Because the available access riser is small, and a wide crawler platform is required to support the spray system, the crawler's frame must fold to enter the tank. After entry into the tank, the crawler unfolds on the tank floor using the crawler drive tracks to expand the frame and position the mobile platform under the entry riser. The spray system will then be lowered separately through the entry riser and mated onto the crawler on the tank floor. The crawler and spray system are tethered and controlled remotely by personnel at the control station. Motorized cable reels will also be remotely controlled to pay out, retrieve, and manage the tethers as the mobile platform moves the spray system across the tank floor. Both the crawler and spray systems are designed to be retrievable. Development of the tank cleaning system was evaluated using a performance test program. The tests evaluated the spray system dynamics, the crawler's fit through the riser, the crawler landing in mocked up tank with simulant, the crawler's traction, and the crawler and spray system mating. Initial testing verified the crawler platform was compatible with the dynamics produced by the spray system. The riser fit test confirmed that a dedicated riser is required for deployment of the crawler and the spray system. The crawler traction test defined the capabilities of the crawler at different levels of simulant. Deployment testing through a mockup riser verified the basic system processes. Finally, testing of the complete system in a full-scale mockup with sludge simulant was performed to evaluate the tank cleaning ability of the crawler. This paper describes th e tank conditions, the tank closure process, the development of the crawler and spray system, and the testing program and results used to evaluate the mobile platform and spray system.« less

EVALUATION OF INNOVATIVE VOLATILE ORGANIC COMPOUND AND HAZARDOUS AIR POLLUTANT CONTROL TECHNOLOGIES FOR U.S. AIR FORCE PAINT SPRAY BOOTHS

EPA Science Inventory

This report gives results of an evaluation of carbon paper adsorption catalytic incineration (CPACI) and fluidized-bed catalytic incineration (FBCI) as control technologies to reduce volatile organic compound (VOC) emissions from paint spray booths.

Skin sterility after application of ethyl chloride spray.

PubMed

Polishchuk, Daniil; Gehrmann, Robin; Tan, Virak

2012-01-18

Ethyl chloride topical anesthetic spray is labeled as nonsterile, yet it is widely used during injection procedures performed in an outpatient setting. The purpose of this study was to investigate the sterility of ethyl chloride topical anesthetic spray applied before an injection. Our a priori hypothesis was that application of the spray after the skin has been prepared would not alter the sterility of the injection site. We conducted a prospective, blinded, controlled study to assess the effect of ethyl chloride spray on skin sterility. Fifteen healthy adult subjects (age, twenty-three to sixty-one years) were prepared for mock injections into both shoulders and both knees, although no injection was actually performed. Three culture samples were obtained from each site on the skin: one before skin preparation with isopropyl alcohol, one after skin preparation and before application of ethyl chloride, and one after ethyl chloride had been sprayed on the site. In addition, the sterility of the ethyl chloride was tested directly by inoculating cultures with spray from the bottles. Growth occurred in 70% of the samples obtained before skin preparation, 3% of the samples obtained after skin preparation but before application of ethyl chloride, and 5% of the samples obtained after the injection site had been sprayed with ethyl chloride. The percentage of positive cultures did not increase significantly after application of ethyl chloride (p = 0.65). Spraying of ethyl chloride directly on agar plates resulted in growth on 13% of these plates compared with 11% of the control plates; this difference was also not significant (p = 0.80). Although ethyl chloride spray is not sterile, its application did not alter the sterility of the injection sites in the shoulder and knee.

Efficacy of clobetasol spray: factors beyond patient compliance.

PubMed

Bhutani, Tina; Koo, John; Maibach, Howard I

2012-02-01

Clobetasol 0.05% spray, a topical clobetasol propionate, is a non-greasy formulation that has shown increased clinical efficacy in a head-to-head comparison with foam formulation. Moreover, available data from randomized, controlled, double-blind trials suggests that clobetasol spray is, in fact, slightly more effective than most, if not all, other preparations of clobetasol. The fact that clobetasol spray is exceptionally easy to comply with may have played a major role in this outcome; however, other factors must be considered. These include vehicle metamorphosis post-application as well as vehicle and excipient effects on stratum corneum permeability. Basic concepts in topical drug delivery and how they apply to this spray vehicle may further explain the greater efficacy of clobetasol spray.

Limit-cycle-based control of the myogenic wingbeat rhythm in the fruit fly Drosophila

PubMed Central

Bartussek, Jan; Mutlu, A. Kadir; Zapotocky, Martin; Fry, Steven N.

2013-01-01

In many animals, rhythmic motor activity is governed by neural limit cycle oscillations under the control of sensory feedback. In the fruit fly Drosophila melanogaster, the wingbeat rhythm is generated myogenically by stretch-activated muscles and hence independently from direct neural input. In this study, we explored if generation and cycle-by-cycle control of Drosophila's wingbeat are functionally separated, or if the steering muscles instead couple into the myogenic rhythm as a weak forcing of a limit cycle oscillator. We behaviourally tested tethered flying flies for characteristic properties of limit cycle oscillators. To this end, we mechanically stimulated the fly's ‘gyroscopic’ organs, the halteres, and determined the phase relationship between the wing motion and stimulus. The flies synchronized with the stimulus for specific ranges of stimulus amplitude and frequency, revealing the characteristic Arnol'd tongues of a forced limit cycle oscillator. Rapid periodic modulation of the wingbeat frequency prior to locking demonstrates the involvement of the fast steering muscles in the observed control of the wingbeat frequency. We propose that the mechanical forcing of a myogenic limit cycle oscillator permits flies to avoid the comparatively slow control based on a neural central pattern generator. PMID:23282849

Hydroxyapatite coatings deposited by liquid precursor plasma spraying: controlled dense and porous microstructures and osteoblastic cell responses.

PubMed

Huang, Yi; Song, Lei; Liu, Xiaoguang; Xiao, Yanfeng; Wu, Yao; Chen, Jiyong; Wu, Fang; Gu, Zhongwei

2010-12-01

Hydroxyapatite coatings were deposited on Ti-6Al-4V substrates by a novel plasma spraying process, the liquid precursor plasma spraying (LPPS) process. X-ray diffraction results showed that the coatings obtained by the LPPS process were mainly composed of hydroxyapatite. The LPPS process also showed excellent control on the coating microstructure, and both nearly fully dense and highly porous hydroxyapatite coatings were obtained by simply adjusting the solid content of the hydroxyapatite liquid precursor. Scanning electron microscope observations indicated that the porous hydroxyapatite coatings had pore size in the range of 10-200 µm and an average porosity of 48.26 ± 0.10%. The osteoblastic cell responses to the dense and porous hydroxyapatite coatings were evaluated with human osteoblastic cell MG-63, in respect of the cell morphology, proliferation and differentiation, with the hydroxyapatite coatings deposited by the atmospheric plasma spraying (APS) process as control. The cell experiment results indicated that the heat-treated LPPS coatings with a porous structure showed the best cell proliferation and differentiation among all the hydroxyapatite coatings. Our results suggest that the LPPS process is a promising plasma spraying technique for fabricating hydroxyapatite coatings with a controllable microstructure, which has great potential in bone repair and replacement applications.

Correlation between Hierarchical Structure and Processing Control of Large-area Spray-coated Polymer Solar Cells toward High Performance

PubMed Central

Huang, Yu-Ching; Tsao, Cheng-Si; Cha, Hou-Chin; Chuang, Chih-Min; Su, Chun-Jen; Jeng, U-Ser; Chen, Charn-Ying

2016-01-01

The formation mechanism of a spray-coated film is different from that of a spin-coated film. This study employs grazing incidence small- and wide-angle X-ray Scattering (GISAXS and GIWAXS, respectively) quantitatively and systematically to investigate the hierarchical structure and phase-separated behavior of a spray-deposited blend film. The formation of PCBM clusters involves mutual interactions with both the P3HT crystal domains and droplet boundary. The processing control and the formed hierarchical structure of the active layer in the spray-coated polymer/fullerene blend film are compared to those in the spin-coated film. How the different post-treatments, such as thermal and solvent vapor annealing, tailor the hierarchical structure of the spray-coated films is quantitatively studied. Finally, the relationship between the processing control and tailored BHJ structures and the performance of polymer solar cell devices is established here, taking into account the evolution of the device area from 1 × 0.3 and 1 × 1 cm2. The formation and control of the special networks formed by the PCBM cluster and P3HT crystallites, respectively, are related to the droplet boundary. These structures are favorable for the transverse transport of electrons and holes. PMID:26817585

House fly (Musca domestica): a review of control strategies for a challenging pest.

PubMed

Malik, Anushree; Singh, Neena; Satya, Santosh

2007-05-01

Musca domestica L. (Diptera: Muscidae), commonly called the house fly, is a major domestic, medical and veterinary pest that causes irritation, spoils food and acts as a vector for many pathogenic organisms. In this paper, the social and health problems related to housefly are introduced with the associated need to control its population. Physical and chemical methods of house fly control are briefly discussed. The main focus of this review is on the biological control methods for house fly control, that comprise botanical, fungal, bacterial and parasitoid agents. Although several biocontrol agents are still in the nascent stage, some of them (especially fungal and parasitoid agents) have shown reliable field performance and seem to be suitable candidates for commercialization. However, the majority of these laboratory and field studies have been conducted in the temperate region. It remains to be seen whether the application of biocontrol agents would be feasible in tropical environments. The integrated pest management practices, which can provide more reliable field performance, have also been discussed. A multi-dimensional approach that exerts control on all the life stages of house fly, but simultaneously preserves the fly's natural enemies could be an ecologically sustainable way of maintaining the fly populations below maximally acceptable limits.

Device and technique for in-process sampling and analysis of molten metals and other liquids presenting harsh sampling conditions

DOEpatents

Alvarez, J.L.; Watson, L.D.

1988-01-21

An apparatus and method for continuously analyzing liquids by creating a supersonic spray which is shaped and sized prior to delivery of the spray to a analysis apparatus. The gas and liquid is sheared into small particles which are of a size and uniformity to form a spray which can be controlled through adjustment of pressures and gas velocity. The spray is shaped by a concentric supplemental flow of gas. 5 figs.

Novel Online Diagnostic Analysis for In-Flight Particle Properties in Cold Spraying

NASA Astrophysics Data System (ADS)

Koivuluoto, Heli; Matikainen, Ville; Larjo, Jussi; Vuoristo, Petri

2018-02-01

In cold spraying, powder particles are accelerated by preheated supersonic gas stream to high velocities and sprayed on a substrate. The particle velocities depend on the equipment design and process parameters, e.g., on the type of the process gas and its pressure and temperature. These, in turn, affect the coating structure and the properties. The particle velocities in cold spraying are high, and the particle temperatures are low, which can, therefore, be a challenge for the diagnostic methods. A novel optical online diagnostic system, HiWatch HR, will open new possibilities for measuring particle in-flight properties in cold spray processes. The system employs an imaging measurement technique called S-PTV (sizing-particle tracking velocimetry), first introduced in this research. This technique enables an accurate particle size measurement also for small diameter particles with a large powder volume. The aim of this study was to evaluate the velocities of metallic particles sprayed with HPCS and LPCS systems and with varying process parameters. The measured in-flight particle properties were further linked to the resulting coating properties. Furthermore, the camera was able to provide information about variations during the spraying, e.g., fluctuating powder feeding, which is important from the process control and quality control point of view.

Evaluating the feasibility of using insecticide quantification kits (IQK) for estimating cyanopyrethroid levels for indoor residual spraying in Vanuatu

PubMed Central

2014-01-01

Background The quality of routine indoor residual spraying (IRS) operations is rarely assessed because of the limited choice of methods available for quantifying insecticide content in the field. This study, therefore, evaluated a user-friendly, rapid colorimetric assay for detecting insecticide content after routine IRS operations were conducted. Methods This study was conducted in Tafea Province, Vanuatu. Routine IRS was conducted with lambda cyhalothrin. Two methods were used to quantify the IRS activities: 1) pre-spray application of small felt pads and 2) post-spray removal of insecticide with adhesive. The insecticide content was quantified using a colorimetric assay (Insecticide Quantification Kit [IQK]), which involved exposing each sample to the test reagents for 15 mins. The concentration of insecticide was indicated by the depth of red colour. Results The IQK proved simple to perform in the field and results could be immediately interpreted by the programme staff. The insecticide content was successfully sampled by attaching felt pads to the house walls prior to spraying. The IRS operation was well conducted, with 83% of houses being sprayed at the target dose (20 – 30 mg AI/m2). The average reading across all houses was 24.4 ± 1.5 mg AI/m2. The results from the felt pads applied pre-spray were used as a base to compare methods for sampling insecticide from walls post-spray. The adhesive of Sellotape did not collect adequate samples. However, the adhesive of the felt pads provided accurate samples of the insecticide content on walls. Conclusion The IQK colorimetric assay proved to be a useful tool that was simple to use under realistic field conditions. The assay provided rapid information on IRS spray dynamics and spray team performance, facilitating timely decision making and reporting for programme managers. The IQK colorimetric assay will have direct applications for routine quality control in malaria control programmes globally and has the potential to improve the efficacy of vector control operations. PMID:24885084

Clinicopathological effects of pepper (oleoresin capsicum) spray.

PubMed

Yeung, M F; Tang, William Y M

2015-12-01

Pepper (oleoresin capsicum) spray is one of the most common riot-control measures used today. Although not lethal, exposure of pepper spray can cause injury to different organ systems. This review aimed to summarise the major clinicopathological effects of pepper spray in humans. MEDLINE, EMBASE database, and Cochrane Database of Systematic Reviews were used to search for terms associated with the clinicopathological effects of pepper spray in humans and those describing the pathophysiology of capsaicin. A phone interview with two individuals recently exposed to pepper spray was also conducted to establish clinical symptoms. Major key words used for the MEDLINE search were "pepper spray", "OC spray", "oleoresin capsicum"; and other key words as "riot control agents", "capsaicin", and "capsaicinoid". We then combined the key words "capsaicin" and "capsaicinoid" with the major key words to narrow down the number of articles. A search with other databases including EMBASE and Cochrane Database of Systematic Reviews was also conducted with the above phrases to identify any additional related articles. All article searches were confined to human study. The bibliography of articles was screened for additional relevant studies including non-indexed reports, and information from these was also recorded. Non-English articles were included in the search. Fifteen articles were considered relevant. Oleoresin capsicum causes almost instantaneous irritative symptoms to the skin, eyes, and respiratory system. Dermatological effects include a burning sensation, erythema, and hyperalgesia. Ophthalmic effects involve blepharospasm, conjunctivitis, peri-orbital oedema, and corneal pathology. Following inhalation, a stinging or burning sensation can be felt in the nose with sore throat, chest tightness, or dyspnoea. The major pathophysiology is neurogenic inflammation caused by capsaicinoid in the pepper spray. There is no antidote for oleoresin capsicum. Treatment consists of thorough decontamination, symptom-directed supportive measures, and early detection and treatment of systemic toxicity. Decontamination should be carefully carried out to avoid contamination of the surrounding skin and clothing. Pepper (oleoresin capsicum) spray is an effective riot-control agent and does not cause life-threatening clinical effects in the majority of exposed individuals. Early decontamination minimises the irritant effects.

Laboratory colonization and mass rearing of phlebotomine sand flies (Diptera, Psychodidae)

PubMed Central

Lawyer, Phillip; Killick-Kendrick, Mireille; Rowland, Tobin; Rowton, Edgar; Volf, Petr

2017-01-01

Laboratory colonies of phlebotomine sand flies are necessary for experimental study of their biology, behaviour and mutual relations with disease agents and for testing new methods of vector control. They are indispensable in genetic studies and controlled observations on the physiology and behaviour of sand flies, neglected subjects of high priority. Colonies are of particular value for screening insecticides. Colonized sand flies are used as live vector models in a diverse array of research projects, including xenodiagnosis, that are directed toward control of leishmaniasis and other sand fly-associated diseases. Historically, labour-intensive maintenance and low productivity have limited their usefulness for research, especially for species that do not adapt well to laboratory conditions. However, with growing interest in leishmaniasis research, rearing techniques have been developed and refined, and sand fly colonies have become more common, enabling many significant breakthroughs. Today, there are at least 90 colonies representing 21 distinct phlebotomine sand fly species in 35 laboratories in 18 countries worldwide. The materials and methods used by various sand fly workers differ, dictated by the availability of resources, cost or manpower constraints rather than choice. This paper is not intended as a comprehensive review but rather a discussion of methods and techniques most commonly used by researchers to initiate, establish and maintain sand fly colonies, with emphasis on the methods proven to be most effective for the species the authors have colonized. Topics discussed include collecting sand flies for colony stock, colony initiation, maintenance and mass-rearing procedures, and control of sand fly pathogens in colonies. PMID:29139377

Passive Baited Sequential Fly Trap

USDA-ARS?s Scientific Manuscript database

Sampling fly populations associated with human populations is needed to understand diel behavior and to monitor population densities before and after control operations. Population control measures are dependent on the results of monitoring efforts as they may provide insight into the fly behavior ...

Fungicide resistance profiles for 13 Botrytis cinerea isolated from strawberry in southeastern Louisiana

USDA-ARS?s Scientific Manuscript database

BACKGROUND: Fungicidal sprays have been widely used for disease control of gray mold caused by Botrytis cinerea. In recent years strawberry growers in southeastern Louisiana reported a failure of their fungicide spray programs to control Botrytis fruit rot. Botrytis cinerea has become resistant ...

Evaluation of spray droplet spectrum of sprayers used for vector control

USDA-ARS?s Scientific Manuscript database

Droplet spectra data were collected from spray equipment intended for use in vector control by the US Department of Defense pest management programs to determine if they produce droplets in the ultra-low volume (ULV) spectrum. Droplets generated by 26 sprayers utilizing water + non-ionic surfactant...

Development of a new modular aerial spray system and night application capability for the U.S. Air Force

USDA-ARS?s Scientific Manuscript database

The U.S. Air Force maintains a capability with the C130 aircraft to conduct aerial spray operations over large areas for controlling insects of medical importance. The current modular aerial spray system (MASS) is custom designed to support a variety of configurations from ultralow volume space spra...

Using Tempo to control emerald ash borer: a comparison of trunk and foliage sprays

Treesearch

Deborah G. McCullough; David L. Cappaert; Therese M. Poland

2005-01-01

Insecticide sprays may provide arborists, landscapers, and regulatory officials with a useful option to control emerald ash borer (EAB) in some situations. In our 2003 studies, we found that two applications of Tempo (a pyrethroid insecticide) significantly reduced the density of EAB larvae relative to unsprayed trees. It was not clear, however, whether this control...

Control of free-flying space robot manipulator systems

NASA Technical Reports Server (NTRS)

Cannon, Robert H., Jr.

1977-01-01

To accelerate the development of multi-armed, free-flying satellite manipulators, a fixed-base cooperative manipulation facility is being developed. The work performed on multiple arm cooperation on a free-flying robot is summarized. Research is also summarized on global navigation and control of free-flying space robots. The Locomotion Enhancement via Arm Pushoff (LEAP) approach is described and progress to date is presented.

Design Optimization of Liquid Fueled High Velocity Oxy- Fuel Thermal Spraying Technique for Durable Coating for Fossil Power Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choudhuri, Ahsan; Love, Norman

High-velocity oxy–fuel (HVOF) thermal spraying was developed in 1930 and has been commercially available for twenty-five years. HVOF thermal spraying has several benefits over the more conventional plasma spray technique including a faster deposition rate which leads to quicker turn-around, with more durable coatings and higher bond strength, hardness and wear resistance due to a homogeneous distribution of the sprayed particles. HVOF thermal spraying is frequently used in engineering to deposit cermets, metallic alloys, composites and polymers, to enhance product life and performance. HVOF thermal spraying system is a highly promising technique for applying durable coatings on structural materials formore » corrosive and high temperature environments in advanced ultra-supercritical coal- fired (AUSC) boilers, steam turbines and gas turbines. HVOF thermal spraying is the preferred method for producing coatings with low porosity and high adhesion. HVOF thermal spray process has been shown to be one of the most efficient techniques to deposit high performance coatings at moderate cost. Variables affecting the deposit formation and coating properties include hardware characteristics such as nozzle geometry and spraying distance and process parameters such as equivalence ratio, gas flow density, and powder feedstock. In the spray process, the powder particles experience very high speeds combined with fast heating to the powder material melting point or above. This high temperature causes evaporation of the powder, dissolution, and phase transformations. Due to the complex nature of the HVOF technique, the control and optimization of the process is difficult. In general, good coating quality with suitable properties and required performance for specific applications is the goal in producing thermal spray coatings. In order to reach this goal, a deeper understanding of the spray process as a whole is needed. Although many researchers studied commercial HVOF thermal spray systems, there exists a lack of fundamental understanding of the effect of hardware characteristics and operating parameters on HVOF thermally sprayed coatings. Motivated by these issues, this study is devoted to investigate the effect of hardware characteristics (e.g. spraying distance) and operating parameters (e.g. combustion chamber pressure, equivalence ratio, and total gas flow rate) on HVOF sprayed coatings using Inconel 718 alloy. The current study provides extensive understanding of several key operating and process parameters to optimize the next generation of HVOF thermally sprayed coatings for high temperature and harsh environment applications. A facility was developed to support this endeavor in a safe and efficient way, including a HVOF thermal spray system with a Data Acquisition and Remote Controls system (DARCS). The coatings microstructure and morphology were examined using X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Nanoindentation.« less

Effect of Nozzle Geometry on the Microstructure and Properties of HVAF-Sprayed WC-10Co4Cr and Cr3C2-25NiCr Coatings

NASA Astrophysics Data System (ADS)

Matikainen, V.; Koivuluoto, H.; Vuoristo, P.; Schubert, J.; Houdková, Š.

2018-04-01

Thermally sprayed hard metal coatings are the industrial standard solution for numerous demanding applications to improve wear resistance. In the aim of improving coating quality by utilising finer particle size distributions, several approaches have been studied to control the spray temperature. The most viable solution is to use the modern high velocity air-fuel (HVAF) spray process, which has already proven to produce high-quality coatings with dense structures. In HVAF spray process, the particle heating and acceleration can be efficiently controlled by changing the nozzle geometry. In this study, fine WC-10Co4Cr and Cr3C2-25NiCr powders were sprayed with three nozzle geometries to investigate their effect on the particle temperature, velocity and coating microstructure. The study demonstrates that the particle melting and resulting carbide dissolution can be efficiently controlled by changing the nozzle geometry from cylindrical to convergent-divergent. Moreover, the average particle velocity was increased from 780 to over 900 m/s. The increase in particle velocity significantly improved the coating structure and density. Further evaluation was carried out to resolve the effect of particle in-flight parameters on coating structure and cavitation erosion resistance, which was significantly improved in the case of WC-10Co4Cr coatings with the increasing average particle velocity.

Testing of a Spray-bar Thermodynamic Vent System in Liquid Nitrogen

NASA Technical Reports Server (NTRS)

Flachbart, R. H.; Hastings, L. J.; Hedayat, A.; Nelson, S. L.; Tucker, S. P.

2005-01-01

To support development of a microgravity pressure control capability for liquid oxygen, thermodynamic vent system (TVS) testing was conducted at Marshall Space Flight Center (MSFC) using liquid nitrogen (LN2) as a LOX simulant. The spray bar TVS hardware used was originally designed by the Boeing Company for testing in liquid hydrogen (LH2). With this concept, a small portion of the tank fluid is passed through a Joule-Thomson (J-T) device, and then through a longitudinal spray bar mixed-heat exchanger in order to cool the bulk fluid. To accommodate the larger mass flow rates associated with LN2, the TVS hardware was modified by replacing the recirculation pump with an LN2 compatible pump and replacing the J-T valve. The primary advantage of the spray-bar configuration is that tank pressure control can be achieved independent of liquid and vapor location, enhancing the applicability of ground test data to microgravity conditions. Performance testing revealed that the spray-bar TVS was effective in controlling tank pressure within a 6.89 kPa band for fill levels of 90%, 50%, and 25%. Tests were also conducted with gaseous helium (GHe) in the ullage. The TVS operated nominally with GHe in the ullage, with performance similar to the tests with gaseous nitrogen (GN2). Testing demonstrated that the spray-bar TVS design was flexible enough for use in two different propellants with minimal hardware modifications.

Assessment of exposure to organophosphate insecticides during spraying in Haiti: monitoring of urinary metabolites and blood cholinesterase levels*

PubMed Central

Warren, McWilson; Spencer, Harrison C.; Churchill, Frederick C.; Francois, Velly Jean; Hippolyte, Robert; Staiger, Michael A.

1985-01-01

Measurement of blood cholinesterase activity and of the urinary metabolites of fenitrothion (p-nitrocresol) and malathion (monocarboxylic acid) was used to assess the exposure to these insecticides of workers in the Haitian malaria control programme and of residents in the sprayed houses. Cholinesterase activity was significantly reduced at the end of the working week in 3 out of 28 fenitrothion workers. Urinary levels of p-nitrocresol (PNC) in the spraymen ranged from 2.2 to 25.2 mg/l. In fenitrothion workers who had no direct contact with spraying (weighers and supervisors), the cholinesterase activity remained ≥ 75% of the normal control value, and the urinary PNC levels were relatively low. Urinary malathion monocarboxylic acid (MCA) levels at the end of the working week ranged between 1.1 and 5.3 mg/l in workers using malathion and their blood cholinesterase activity remained essentially normal. In both groups of workers the cholinesterase levels improved and the urinary excretion of metabolites decreased after 2 days of rest from the spraying operations. In the residents of the sprayed houses, low concentrations of PNC and MCA were detected in the urine 1 day after spraying and measurable but reduced levels were still present after 7 days. In all these cases the cholinesterase activity remained ≥ 75% of the normal control value. PMID:3874716

Improvement of mass-rearing procedures for an olive fruit fly parasitoid – duration of exposure to hosts affects production of Psyttalia lounsburyi

USDA-ARS?s Scientific Manuscript database

The olive fruit fly, Bactrocera oleae (Diptera: Tephritidae), causes severe economic damage in California. Control of this fly is currently limited to pesticides. The USDA-ARS European Biological Control Laboratory in Montpellier, France established a classical biological control program nearly 15 y...

Influence of Cold-Sprayed, Warm-Sprayed, and Plasma-Sprayed Layers Deposition on Fatigue Properties of Steel Specimens

NASA Astrophysics Data System (ADS)

Cizek, J.; Matejkova, M.; Dlouhy, I.; Siska, F.; Kay, C. M.; Karthikeyan, J.; Kuroda, S.; Kovarik, O.; Siegl, J.; Loke, K.; Khor, Khiam Aik

2015-06-01

Titanium powder was deposited onto steel specimens using four thermal spray technologies: plasma spray, low-pressure cold spray, portable cold spray, and warm spray. The specimens were then subjected to strain-controlled cyclic bending test in a dedicated in-house built device. The crack propagation was monitored by observing the changes in the resonance frequency of the samples. For each series, the number of cycles corresponding to a pre-defined specimen cross-section damage was used as a performance indicator. It was found that the grit-blasting procedure did not alter the fatigue properties of the steel specimens (1% increase as compared to as-received set), while the deposition of coatings via all four thermal spray technologies significantly increased the measured fatigue lives. The three high-velocity technologies led to an increase of relative lives to 234% (low-pressure cold spray), 210% (portable cold spray), and 355% (warm spray) and the deposition using plasma spray led to an increase of relative lives to 303%. The observed increase of high-velocity technologies (cold and warm spray) could be attributed to a combination of homogeneous fatigue-resistant coatings and induction of peening stresses into the substrates via the impingement of the high-kinetic energy particles. Given the intrinsic character of the plasma jet (low-velocity impact of semi/molten particles) and the mostly ceramic character of the coating (oxides, nitrides), a hypothesis based on non-linear coatings behavior is provided in the paper.

Biological Control of Olive Fruit Fly

USDA-ARS?s Scientific Manuscript database

Domestication of olive fruit, Olea europaea L., produced a better host for olive fruit fly, Bactrocera oleae (Gmelin), than wild olives, but fruit domestication reduced natural enemy efficiency. Important factors for selection of natural enemies for control of olive fruit fly include climate matchi...

The secondary release of mercury in coal fly ash-based flue-gas mercury removal technology.

PubMed

He, Jingfeng; Duan, Chenlong; Lei, Mingzhe; Zhu, Xuemei

2016-01-01

The secondary release of mercury from coal fly ash is a negative by-product from coal-fired power plants, and requires effective control to reduce environmental pollution. Analysing particle size distribution and composition of the coal fly ash produced by different mercury removing technologies indicates that the particles are generally less than 0.5 mm in size and are composed mainly of SiO2, Al2O3, and Fe2O3. The relationships between mercury concentration in the coal fly ash, its particle size, and loss of ignition were studied using different mercury removing approaches. The research indicates that the coal fly ash's mercury levels are significantly higher after injecting activated carbon or brominating activated carbon when compared to regular cooperating-pollution control technology. This is particularly true for particle size ranges of >0.125, 0.075-0.125, and 0.05-0.075 mm. Leaching experiments revealed the secondary release of mercury in discarded coal fly ash. The concentration of mercury in the coal fly ash increases as the quantity of injecting activated carbon or brominating activated carbon increases. The leached concentrations of mercury increase as the particle size of the coal fly ash increases. Therefore, the secondary release of mercury can be controlled by adding suitable activated carbon or brominating activated carbon when disposing of coal fly ash. Adding CaBr2 before coal combustion in the boiler also helps control the secondary release of mercury, by increasing the Hg(2+) concentration in the leachate. This work provides a theoretical foundation for controlling and removing mercury in coal fly ash disposal.

Application Of Holography In The Distribution Measurement Of Fuel Spraying Field In Diesel Engines

NASA Astrophysics Data System (ADS)

Xiang, He Wan; Xiong, Li Zhi

1988-01-01

The distribution of fuel spraying field in the combustion chamber is an important factor which influences the performance of diesel engines. Precise data for those major parameters of the spraying field distribution are difficult to obtain using conventional ways of measurement, so its effects on the combustion process cannot be controlled. The laser holographic measurement is used and many researches have been made on the injecting nozzles used in diesel engines Series 95, 100 and 130. These researches show that clear spraying field hologram can be taken with an "IC Engine Laser Holography System". By rendition and data processing, droplet size, amount and their space distribution in the spraying; the spraying range, cone angle and other dependable data can be obtained. Therefore, the spraying quality of an injecting nozzle can be precisely determined, which provides reliable basis for the improvement of diesel engines' functions.

Venom-spraying behavior of the scorpion Parabuthus transvaalicus (Arachnida: Buthidae).

PubMed

Nisani, Zia; Hayes, William K

2015-06-01

Many animals use chemical squirting or spraying behavior as a defensive response. Some members of the scorpion genus Parabuthus (family Buthidae) can spray their venom. We examined the stimulus control and characteristics of venom spraying by Parabuthus transvaalicus to better understand the behavioral context for its use. Venom spraying occurred mostly, but not always, when the metasoma (tail) was contacted (usually grasped by forceps), and was absent during stinging-like thrusts of the metasoma apart from contact. Scorpions were significantly more likely to spray when contact was also accompanied by airborne stimuli. Sprays happened almost instantaneously following grasping by forceps (median=0.23s) as a brief (0.07-0.30s, mean=0.18s), fine stream (<5° arc) that was not directed toward the stimulus source; however, rapid independent movements of the metasoma and/or telson (stinger) often created a more diffuse spray, increasing the possibility of venom contact with the sensitive eyes of potential scorpion predators. Successive venom sprays varied considerably in duration and velocity. Collectively, these results suggest that venom spraying might be useful as an antipredator function and can be modulated based on threat. Copyright © 2015 Elsevier B.V. All rights reserved.

Pesticide Spraying for West Nile Virus Control and Emergency Department Asthma Visits in New York City, 2000

PubMed Central

Karpati, Adam M.; Perrin, Mary C.; Matte, Tom; Leighton, Jessica; Schwartz, Joel; Barr, R. Graham

2004-01-01

Pyrethroid pesticides were applied via ground spraying to residential neighborhoods in New York City during July–September 2000 to control mosquito vectors of West Nile virus (WNV). Case reports link pyrethroid exposure to asthma exacerbations, but population-level effects on asthma from large-scale mosquito control programs have not been assessed. We conducted this analysis to determine whether widespread urban pyrethroid pesticide use was associated with increased rates of emergency department (ED) visits for asthma. We recorded the dates and locations of pyrethroid spraying during the 2000 WNV season in New York City and tabulated all ED visits for asthma to public hospitals from October 1999 through November 2000 by date and ZIP code of patients’ residences. The association between pesticide application and asthma-related emergency visits was evaluated across date and ZIP code, adjusting for season, day of week, and daily temperature, precipitation, particulate, and ozone levels. There were 62,827 ED visits for asthma during the 14-month study period, across 162 ZIP codes. The number of asthma visits was similar in the 3-day periods before and after spraying (510 vs. 501, p = 0.78). In multivariate analyses, daily rates of asthma visits were not associated with pesticide spraying (rate ratio = 0.92; 95% confidence interval, 0.80–1.07). Secondary analyses among children and for chronic obstructive pulmonary disease yielded similar null results. This analysis shows that spraying pyrethroids for WNV control in New York City was not followed by population-level increases in public hospital ED visit rates for asthma. PMID:15289164

Use of biocidal products (insect sprays and electro-vaporizer) in indoor areas--exposure scenarios and exposure modeling.

PubMed

Berger-Preiss, Edith; Koch, Wolfgang; Gerling, Susanne; Kock, Heiko; Appel, Klaus E

2009-09-01

Five commercially available insect sprays were applied in a model room. Spraying was performed in accordance with the manufacturers' instructions and in an overdosed manner in order to simulate worst-case conditions or an unforeseeable misuse. In addition, we examined electro-vaporizers. The Respicon aerosol monitoring system was applied to determine inhalation exposure. During normal spraying (10 seconds) and during the following 2-3 minutes, exposure concentrations ranged from 70 to 590 microg/m3 for the pyrethroids tetramethrin, d-phenothrin, cyfluthrin, bioallethrin, and the pyrethrins. Calculated inhalable doses were 2-16 microg. A concentration of approximately 850 microg chlorpyrifos/m(3) (inhalable dose: approximately 20 microg) was determined when the "Contra insect fly spray" was applied. Highest exposure concentrations (1100-2100 microg/m3) were measured for piperonyl butoxide (PBO), corresponding to an inhalation intake of 30-60microg. When simulating worst-case conditions, exposure concentrations of 200-3400microg/m3 and inhalable doses of 10-210microg were determined for the various active substances. Highest concentrations (4800-8000 microg/m3) were measured for PBO (inhalable: 290-480 microg). By applying the electro-vaporizer "Nexa Lotte" plug-in mosquito killer concentrations for d-allethrin were in the range of 5-12microg/m3 and 0.5-2 microg/m3 for PBO while with the "Paral" plug-in mosquito killer concentrations of 0.4-5microg/m3 for pyrethrins and 1-7 microg/m3 for PBO were measured. Potential dermal exposures were determined using exposure pads. Between 80 and 1000microg active substance (tetramethrin, phenothrin, cyfluthrin, bioallethrin, pyrethrins, chlorpyrifos) were deposited on the clothing of the total body surface area of the spray user. Highest levels (up to 3000 microg) were determined for PBO. Worst-case uses of the sprays led to 5-9 times higher concentrations. Also a 2-hour stay nearby an operating electro-vaporizer led to a contamination of the clothing (total amounts on the whole body were 450 microg d-allethrin and 50 microg PBO for "Nexa Lotte" plug-in mosquito killer and 80 microg pyrethrins and 190 microg PBO for "Paral" plug-in mosquito killer). Human biomonitoring data revealed urine concentrations of the metabolite (E)-trans-chrysanthemum dicarboxylic acid ((E)-trans-CDCA) between 1.7 microg/l and 7.1 microg/l after 5 minutes of exposure to the different sprays. Also the use of electro-vaporizers led to (E)-trans-CDCA concentrations in the urine in the range of 1.0 microg/l to 6.2 microg/l (1-3 hours exposure period). The exposure data presented can be used for performing human risk assessment when these biocidal products were applied indoors. The airborne concentrations of the non-volatile active chemical compounds could be predicted from first principles using a deterministic exposure model (SprayExpo).

Methods of synthesizing hydroxyapatite powders and bulk materials

DOEpatents

Luo, Ping

1999-01-12

Methods are provided for producing non-porous controlled morphology hydroxyapatite granules of less than 8 .mu.m by a spray-drying process. Solid or hollow spheres or doughnuts can be formed by controlling the volume fraction and viscosity of the slurry as well as the spray-drying conditions. Methods of providing for homogenous cellular structure hydroxyapatite granules are also provided. Pores or channels or varying size and number can be formed by varying the temperature at which a hydroxyapatite slurry formed in basic, saturated ammonium hydroxide is spray-dried. Methods of providing non-porous controlled morphology hydroxyapatite granules in ammonium hydroxide are also provided. The hydroxyapatite granules and bulk materials formed by these methods are also provided.

Methods of synthesizing hydroxyapatite powders and bulk materials

DOEpatents

Luo, P.

1999-01-12

Methods are provided for producing non-porous controlled morphology hydroxyapatite granules of less than 8 {micro}m by a spray-drying process. Solid or hollow spheres or doughnuts can be formed by controlling the volume fraction and viscosity of the slurry as well as the spray-drying conditions. Methods of providing for homogeneous cellular structure hydroxyapatite granules are also provided. Pores or channels or varying size and number can be formed by varying the temperature at which a hydroxyapatite slurry formed in basic, saturated ammonium hydroxide is spray-dried. Methods of providing non-porous controlled morphology hydroxyapatite granules in ammonium hydroxide are also provided. The hydroxyapatite granules and bulk materials formed by these methods are also provided. 26 figs.

Augmentative Biological Control Using Parasitoids for Fruit Fly Management in Brazil

PubMed Central

Garcia, Flávio R. M.; Ricalde, Marcelo P.

2012-01-01

The history of classical biological control of fruit flies in Brazil includes two reported attempts in the past 70 years. The first occurred in 1937 when an African species of parasitoid larvae (Tetrastichus giffardianus) was introduced to control the Mediterranean fruit fly, Ceratitis capitata and other tephritids. The second occurred in September 1994 when the exotic parasitoid Diachasmimorpha longicaudata, originally from Gainesville, Florida, was introduced by a Brazilian agricultural corporation (EMBRAPA) to evaluate the parasitoid’s potential for the biological control of Anastrepha spp. and Ceratitis capitata. Although there are numerous native Brazilian fruit fly parasitoids, mass rearing of these native species is difficult. Thus, D. longicaudata was chosen due to its specificity for the family Tephritidae and its ease of laboratory rearing. In this paper we review the literature on Brazilian fruit fly biological control and suggest that those tactics can be used on a large scale, together creating a biological barrier to the introduction of new fruit fly populations, reducing the source of outbreaks and the risk of species spread, while decreasing the use of insecticides on fruit destined for domestic and foreign markets. PMID:26466795

An investigation of flow-limited field-injection electrostatic spraying (FFESS) and its applications to thin film deposition

NASA Astrophysics Data System (ADS)

Singh, Ravindra Pratap

Electrostatic spraying is the process of controlled disruption of a liquid surface due to excess surface charge density. The technique has found applications in a wide range of fields from agricultural sprays to fuel injectors to colloidal thrusters for space vehicle propulsion. Over the past 20 years, the technique has been intensely studied in material processing for synthesis of ceramic and metal powders, nanoparticles and thin films. The importance of the technique lies in its simple setup, high deposition efficiency, and ambient atmosphere operation. In conventional electrostatic spraying (CESS), one uses a conducting nozzle to charge the liquid, mostly by induction charging. CESS is therefore restricted to the single jet mode of spraying which occurs at low spray currents. It lacks stability and reproducibility in the high current, multiple jet regime, which can generate much finer sprays. In flow-limited field-injection electrostatic spraying (FFESS), one uses a field-injection electrode to stably and controllably inject higher currents into the liquid, a la Fowler-Nordheim, using an otherwise insulating nozzle. This way, it is possible to stably electrospray in the multiple jet mode. In addition to producing much finer sprays, the multi-jet mode atomizes liquids at higher rates, and spreads the spray over a wider region and more uniformly than single jet sprays, thus paving way for large-area uniform thin film deposition. A simple yet comprehensive theory is formulated to describe the multi jet formation. The theory, which is based on the energy minimization principle, takes into account, for the first time, the interactions between charged jets which leads to saturation in the number of jets at high spray currents. The possibility of using an array of nozzles to obtain uniform large-area high-throughput thin film deposition is also investigated. A large number of FFESS nozzles with alternating positive and negative polarities arranged in a periodic 2-dimensional array are found to produce uniform thin films over large areas. Deposition of TiO2 and silver thin films using multi jet FFESS is studied, demonstrating great control on film morphology and properties. TiO2 thin films deposited on high-intensity discharge arc lamps are found to improve the quality of its light output. Silver thin films of high purity and conductivity, and with good adhesion, could be deposited at relatively high deposition rates and high deposition efficiency as compared to CVD techniques.

Field Study of the Comparative Efficacy of Three Pyrethroid/Neonicotinoid Mixture Products for the Control of the Common Bed Bug, Cimex lectularius.

PubMed

Wang, Changlu; Singh, Narinderpal; Cooper, Richard

2015-03-18

Three insecticide mixtures that contain two classes of insecticides (pyrethroid and neonicotinoid) were recently developed to control bed bugs. We evaluated three integrated bed bug management strategies in apartments, each using the same non-chemical control methods and one of the three insecticide mixture products: Tandem (lambda-cyhalothrin + thiamethoxam), Temprid SC (beta-cyfluthrin + imidacloprid), and Transport Mikron (bifenthrin + acetamiprid). No insecticides were applied in the Control apartments. In all apartments, we installed vinyl mattress encasements (if not already present) and applied steam to beds and other infested upholstered furniture. Insecticide sprays were applied in the three treatments. Each treatment and the Control included 8-10 occupied apartments. Re-treatment was conducted during biweekly inspections if necessary. After eight weeks, the mean (± SEM) bed bug count reduction in the Tandem, Temprid SC, Transport Mikron, and Control was 89 ± 9, 87 ± 6, 98 ± 1, and 23 ± 54%, respectively. Only Tandem and Transport Mikron treatments resulted in significantly higher population reduction than the Control at eight weeks. There were no significant differences in mean percent reduction among the three treatments (Tandem, Temprid SC, Transport Mikron) at eight weeks. Tandem spray caused significantly faster bed bug reduction than Temprid SC spray and Transport Mikron spray.

Multiphysics control of a two-fluid coaxial atomizer supported by electric-charge on the liquid jet

NASA Astrophysics Data System (ADS)

Machicoane, Nathanael; Osuna, Rodrigo; Aliseda, Alberto

2017-11-01

We present an experimental setup to investigate multiphysics control strategies on atomization of a laminar fluid stream by a coaxial turbulent jet. Spray control (i.e. driving the droplet size distribution and the spatio-temporal location of the droplets towards a desired objective) has many potential engineering applications, but requires a mechanistic understanding of the processes that control droplet formation and transport (primary and secondary instabilities, turbulent transport, hydrodynamic and electric forces on the droplets, ...). We characterize experimentally the break-up dynamics in a canonical coaxial atomizer, and the spray structure (droplet size, location, and velocity as a function of time) in a series of open loop conditions with harmonic forcing of the gas swirl ratio, liquid injection rate, the electric field strength at the nozzle and along the spray development region. The effect of these actuators are characterized for different gas Reynolds numbers ranging from 104-106. This open-loop characterization of the injector will be used to develop reduced order models for feedback control, as well as to validate assumptions underlying an adjoint-based computational control strategy. This work is part of a large-scale project funded by an ONR MURI to provide fundamental understanding of the mechanisms for feedback control of sprays.

Field Study of the Comparative Efficacy of Three Pyrethroid/Neonicotinoid Mixture Products for the Control of the Common Bed Bug, Cimex lectularius

PubMed Central

Wang, Changlu; Singh, Narinderpal; Cooper, Richard

2015-01-01

Three insecticide mixtures that contain two classes of insecticides (pyrethroid and neonicotinoid) were recently developed to control bed bugs. We evaluated three integrated bed bug management strategies in apartments, each using the same non-chemical control methods and one of the three insecticide mixture products: Tandem (lambda-cyhalothrin + thiamethoxam), Temprid SC (beta-cyfluthrin + imidacloprid), and Transport Mikron (bifenthrin + acetamiprid). No insecticides were applied in the Control apartments. In all apartments, we installed vinyl mattress encasements (if not already present) and applied steam to beds and other infested upholstered furniture. Insecticide sprays were applied in the three treatments. Each treatment and the Control included 8–10 occupied apartments. Re-treatment was conducted during biweekly inspections if necessary. After eight weeks, the mean (± SEM) bed bug count reduction in the Tandem, Temprid SC, Transport Mikron, and Control was 89 ± 9, 87 ± 6, 98 ± 1, and 23 ± 54%, respectively. Only Tandem and Transport Mikron treatments resulted in significantly higher population reduction than the Control at eight weeks. There were no significant differences in mean percent reduction among the three treatments (Tandem, Temprid SC, Transport Mikron) at eight weeks. Tandem spray caused significantly faster bed bug reduction than Temprid SC spray and Transport Mikron spray. PMID:26463075

Characteristics of spray coverage from an air-blast sprayer, and why this is of concern for disease control in tall pecan trees

USDA-ARS?s Scientific Manuscript database

Application of fungicide sprays to pecan trees is challenging due to the height of the canopy above ground and the limitations of the ground-based spray application equipment (usually orchard air-blast sprayers). We describe results of experiments at the USDA, Byron, GA that were aimed to characteri...

Arc spray fabrication of metal matrix composite monotape

NASA Technical Reports Server (NTRS)

Westfall, L. J. (Inventor)

1985-01-01

Arc metal spraying is used to spray liquid metal onto an array of high strength fibers that were previously wound onto a large drum contained inside a controlled atmosphere chamber. This chamber is first evacuated to remove gaseous contaminants and then backfilled with a neutral gas up to atmospheric pressure. This process is used to produce a large size metal matrix composite monotape.

Automatic targeting of plasma spray gun

DOEpatents

Abbatiello, Leonard A.; Neal, Richard E.

1978-01-01

A means for monitoring the material portion in the flame of a plasma spray gun during spraying operations is provided. A collimated detector, sensitive to certain wavelengths of light emission, is used to locate the centroid of the material with each pass of the gun. The response from the detector is then relayed to the gun controller to be used to automatically realign the gun.

Portable Spray Booth

NASA Technical Reports Server (NTRS)

Hansen, Timothy D.; Bardwell, Micheal J.

1996-01-01

Portable spray booth provides for controlled application of coating materials with high solvent contents. Includes contoured shroud and carbon filter bed limiting concentration of fumes in vicinity. Designed to substitute spraying for brush application of solvent-based adhesive prior to installing rubber waterproof seals over joints between segments of solid-fuel rocket motor. With minor adjustments and modifications, used to apply other solvent-based adhesives, paints, and like.

Testing aerially applied Orthene for control of larch casebearer.

Treesearch

John S. Hard; Stanley Meso; Michael Haskett

1979-01-01

Orthene was tested in a randomized block experiment to determine efficacy against larch casebearer. Needlemining larval populations were sprayed in September 1976 by helicopter with 0.5 lb Orthene/gal water/acre (560 g a.i/9.3 l/ha). Spray deposit was sampled with Kromekote cards. Plot mean larval populations, spray deposit, and defoliation index were analyzed to...

Autonomous Flying Controls Testbed

NASA Technical Reports Server (NTRS)

Motter, Mark A.

2005-01-01

The Flying Controls Testbed (FLiC) is a relatively small and inexpensive unmanned aerial vehicle developed specifically to test highly experimental flight control approaches. The most recent version of the FLiC is configured with 16 independent aileron segments, supports the implementation of C-coded experimental controllers, and is capable of fully autonomous flight from takeoff roll to landing, including flight test maneuvers. The test vehicle is basically a modified Army target drone, AN/FQM-117B, developed as part of a collaboration between the Aviation Applied Technology Directorate (AATD) at Fort Eustis,Virginia and NASA Langley Research Center. Several vehicles have been constructed and collectively have flown over 600 successful test flights.

Turning behaviour depends on frictional damping in the fruit fly Drosophila.

PubMed

Hesselberg, Thomas; Lehmann, Fritz-Olaf

2007-12-01

Turning behaviour in the fruit fly Drosophila depends on several factors including not only feedback from sensory organs and muscular control of wing motion, but also the mass moments of inertia and the frictional damping coefficient of the rotating body. In the present study we evaluate the significance of body friction for yaw turning and thus the limits of visually mediated flight control in Drosophila, by scoring tethered flies flying in a flight simulator on their ability to visually compensate a bias on a moving object and a visual background panorama at different simulated frictional dampings. We estimated the fly's natural damping coefficient from a numerical aerodynamic model based on both friction on the body and the flapping wings during saccadic turning. The model predicts a coefficient of 54 x 10(-12) Nm s, which is more than 100-times larger than the value estimated from a previous study on the body alone. Our estimate suggests that friction plays a larger role for yaw turning in Drosophila than moments of inertia. The simulator experiments showed that visual performance of the fruit fly collapses near the physical conditions estimated for freely flying animals, which is consistent with the suggested role of the halteres for flight stabilization. However, kinematic analyses indicate that the measured loss of flight control might be due predominantly to the limited fine control in the fly's steering muscles below a threshold of 1-2 degrees stroke amplitude, rather than resulting from the limits of visual motion detection by the fly's compound eyes. We discuss the impact of these results and suggest that the elevated frictional coefficient permits freely flying fruit flies to passively terminate rotational body movements without producing counter-torque during the second half of the saccadic turning manoeuvre.

Light extinction method on high-pressure diesel injection

NASA Astrophysics Data System (ADS)

Su, Tzay-Fa; El-Beshbeeshy, Mahmound S.; Corradini, Michael L.; Farrell, Patrick V.

1995-09-01

A two dimensional optical diagnostic technique based on light extinction was improved and demonstrated in an investigation of diesel spray characteristics at high injection pressures. Traditional light extinction methods require the spray image to be perpendicular to the light path. In the improved light extinction scheme, a tilted spray image which has an angle with the light path is still capable of being processed. This technique utilizes high speed photography and digital image analysis to obtain qualitative and quantitative information of the spray characteristics. The injection system used was an electronically controlled common rail unit injector system with injection pressures up to 100 MPa. The nozzle of the injector was a mini-sac type with six holes on the nozzle tip. Two different injection angle nozzles, 125 degree(s) and 140 degree(s), producing an in-plane tilted spray and an out of plane tilted spray were investigated. The experiments were conducted on a constant volume spray chamber with the injector mounted tilted at an angle of 62.5 degree(s)$. Only one spray plume was viewed, and other sprays were free to inject to the chamber. The spray chamber was pressurized with argon and air under room temperature to match the combustion chamber density at the start of the injection. The experimental results show that the difference in the spray tip penetration length, spray angle, and overall average Sauter mean diameter is small between the in- plane tilted spray and the out of plane tilted spray. The results also show that in-plane tilted spray has a slightly larger axial cross- section Sauter mean diameter than the out of plane tilted spray.

Laboratory evaluation of electrostatic spray wet scrubber to control particulate matter emissions from poultry facilities

USDA-ARS?s Scientific Manuscript database

Particulate matter (PM) is a major air pollutant emitted from animal production and has significant impacts on health and the environment. Abatement of PM emissions is imperative and effective PM control technologies are strongly needed. In this work, an electrostatic spray wet scrubber (ESWS) techn...

DEMONSTRATION OF A PAINT SPRAY BOOTH EMISSION CONTROL STRATEGY USING RECIRCULATION/PARTITIONING & UV/OZONE POLLUTION EMISSION CONTROL - VOLUME 1. TECHNICAL REPORT

EPA Science Inventory

The report describes in detail the source testing, construction, and data reduction/analysis activities that comprise the three phases of a technology demonstration program. Phase I consisted of a detailed baseline evaluation of several paint spray booths operated at the Barstow,...

Resting behaviour of Anopheles stephensi type form to assess its amenability to control malaria through indoor residual spray.

PubMed

Nagpal, B N; Srivastava, Aruna; Dash, A P

2012-09-01

In the present study, an attempt was made to find reasons of ineffectiveness of indoor residual spray to interrupt malaria transmission by investigating the behaviour of two variants of Anopheles stepnesi, viz. type form and mysorensis in rural areas of Rajasthan, India. Both low malarious (DDT spray from 1958 to 1976) and high malarious (DDT spray from 1958 to April 2006) villages were selected for the study in Arid zone district Jodhpur, Rajasthan during March-April 2006. Resting behaviour of the species during all its movement rhythms covering 24 h period related to: (i) swarming/ mating; (ii) pre- and post-biting rest; (iii) after feed resting between hoping movements; (iv) night and day time resting and; (v) diel activity movements in response to temperature changes, were carried out. The results showed that household objects like cupboards, furnitures, hanging clothes, goods stacked on loft, stored clothes, cobwebs and floor were the dominant resting sites both in sprayed and unsprayed villages. About 95 and 97% of An. stephensi preferred to rest on household objects of unsprayed and sprayed villages respectively. There was no significant difference in resting behaviour of the species in both groups of villages (p >0.05). The pre-biting resting time was recorded as 5 to 15 min whereas post-biting resting time lasted for 15 to 25 min. After biting outdoor (in courtyard--open to sky) species starts entering the rooms at around 2330 hrs. It was observed that during III quarter (0100 to 0400 hrs) maximum species entered into the room were 56% in unsprayed and 62% in sprayed villages. Statistically there was no significant difference in the entry of mosquitoes (p >0.05) in both the groups of villages. Before DDT era, An. stephensi was found resting at all heights of the walls inside the human dwellings. Present study revealed that An. stephensi is trying to avoid sprayable surfaces and tend to rest on unsprayable surfaces during all its movement rhythms starting from swarming, pre-/post-biting and during hopping movements in the courtyard and thereafter household objects inside the room as final day time resting. It was concluded that changed behaviour of resting of An. stephensi on unsprayable objects in sprayed rooms largely accounted for failure of malaria control. Control of An. stephensi, thus requires an integrated vector control strategy based upon interesectoral, environmental, larviciding with chemical/biolarvicide and use of larvivorous fish wherever feasible. Such a control strategy offers cost-effective and sustainable option than indoor residual spray.

Flight-Test Validation and Flying Qualities Evaluation of a Rotorcraft UAV Flight Control System

NASA Technical Reports Server (NTRS)

Mettler, Bernard; Tuschler, Mark B.; Kanade, Takeo

2000-01-01

This paper presents a process of design and flight-test validation and flying qualities evaluation of a flight control system for a rotorcraft-based unmanned aerial vehicle (RUAV). The keystone of this process is an accurate flight-dynamic model of the aircraft, derived by using system identification modeling. The model captures the most relevant dynamic features of our unmanned rotorcraft, and explicitly accounts for the presence of a stabilizer bar. Using the identified model we were able to determine the performance margins of our original control system and identify limiting factors. The performance limitations were addressed and the attitude control system was 0ptimize.d for different three performance levels: slow, medium, fast. The optimized control laws will be implemented in our RUAV. We will first determine the validity of our control design approach by flight test validating our optimized controllers. Subsequently, we will fly a series of maneuvers with the three optimized controllers to determine the level of flying qualities that can be attained. The outcome enable us to draw important conclusions on the flying qualities requirements for small-scale RUAVs.

A Multiple-Dose, Randomized, Double-Blind, Placebo-Controlled, Parallel-Group QT/QTc Study to Evaluate the Electrophysiologic Effects of THC/CBD Spray.

PubMed

Sellers, Edward M; Schoedel, Kerri; Bartlett, Cindy; Romach, Myroslava; Russo, Ethan B; Stott, Colin G; Wright, Stephen; White, Linda; Duncombe, Paul; Chen, Chien-Feng

2013-07-01

Delta-9-tetrahydrocannabinol (THC)/cannabidiol (CBD) oromucosal spray has proved efficacious in the treatment of spasticity in multiple sclerosis and chronic pain. A thorough QT/QTc study was performed to investigate the effects of THC/CBD spray on electrocardiogram (ECG) parameters in compliance with regulatory requirements, evaluating the effect of a recommended daily dose (8 sprays/day) and supratherapeutic doses (24 or 36 sprays/day) of THC/CBD spray on the QT/QTc interval in 258 healthy volunteers. The safety, tolerability, and pharmacokinetic profile of THC/CBD spray were also evaluated. Therapeutic and supratherapeutic doses of THC/CBD spray had no effect on cardiac repolarization with primary and secondary endpoints of QTcI and QTcF/QTcB, respectively, showing similar results. There was no indication of any effect on heart rate, atrioventricular conduction, or cardiac depolarization and no new clinically relevant morphological changes were observed. Overall, 19 subjects (25.0%) in the supratherapeutic (24/36 daily sprays of THC/CBD spray) dose group and one (1.6%) in the moxifloxacin group withdrew early due to intolerable AEs. Four psychiatric serious adverse events (AEs) in the highest dose group resulted in a reduction in the surpatherapeutic dose to 24 sprays/day. In conclusion, THC/CBD spray does not significantly affect ECG parameters. Additionally, THC/CBD spray is well tolerated at therapeutic doses with an AE profile similar to previous clinical studies. © The Author(s) 2013.

Pest Control on the "Fly"

NASA Technical Reports Server (NTRS)

2002-01-01

FlyCracker(R), a non-toxic and environmentally safe pesticide, can be used to treat and control fly problems in closed environments such as milking sheds, cattle barns and hutches, equine stables, swine pens, poultry plants, food-packing plants, and even restaurants, as well as in some outdoor animal husbandry environments. The product can be applied safely in the presence of animals and humans, and was recently permitted for use on organic farms as livestock production aids. FlyCracker's carbohydrate technology kills fly larvae within 24 hours. By killing larvae before they reach the adult stages, FlyCracker eradicates another potential breeding population. Because the process is physical-not chemical-flies and other insects never develop resistance to the treatment, giving way to unlimited use of product, while still keeping the same powerful effect.

Synthesis and characterization of Cu3(BTC)2 membranes by thermal spray seeding and secondary growth.

PubMed

Noh, Seung-Jun; Kwon, Hyuk Taek; Kim, Jinsoo

2013-08-01

Crack-free Cu3(BTC)2 membranes were successfully prepared by thermal spray seeding and secondary growth method. Thermal spray seeding method, combining thermal seeding and pressurized spraying, uniformly distributed seed solution on the support, anchoring seed crystals tightly on the support. After secondary growth of the seeded support in the autoclave, continuous crack-free membrane was obtained by controlling cooling and drying steps. The gas permeation test was conducted at various temperatures using H2, CO2, CH4 and N2 gases.

Penetration and Duration of Fuel Sprays from a Pump Injection System

NASA Technical Reports Server (NTRS)

Rothrock, A M; Marsh, E T

1934-01-01

High-speed motion pictures were taken of individual fuel sprays from a pump injection system. The changes in the spray-tip penetration with changes in the pump speed, injection-valve opening and closing pressures, discharge-orifice area, injection-tube length and diameter, and pump throttle setting were measured. The pump was used with and without a check valve. The results show that the penetration of the spray tip can be controlled by the dimensions of the injection tube, the area of the discharge orifice, and the injection-valve opening and closing pressures.

Device and technique for in-process sampling and analysis of molten metals and other liquids presenting harsh sampling conditions

DOEpatents

Alvarez, Joseph L.; Watson, Lloyd D.

1989-01-01

An apparatus and method for continuously analyzing liquids by creating a supersonic spray which is shaped and sized prior to delivery of the spray to a analysis apparatus. The gas and liquid are mixed in a converging-diverging nozzle where the liquid is sheared into small particles which are of a size and uniformly to form a spray which can be controlled through adjustment of pressures and gas velocity. The spray is shaped by a concentric supplemental flow of gas.

Pneumotoxicity and pulmonary clearance of different welding fumes after intratracheal instillation in the rat.

PubMed

Antonini, J M; Krishna Murthy, G G; Rogers, R A; Albert, R; Ulrich, G D; Brain, J D

1996-09-01

The objectives of this study were to compare different welding fumes in regard to their potential to elicit lung inflammation or injury and to examine possible mechanisms whereby welding fumes may damage the lungs. Fume was collected on filters from conventional spray [mild steel (MS-SPRAY) or stainless steel (SS-SPRAY) electrode wire] or pulsed current [mild steel (MS-PULSE) electrode wire] gas-shielded metal arc welding. Rats were given one of the three welding fume samples by intratracheal instillation (1.0 mg/100 g body wt). Other rats received a relatively inert dust (iron oxide), a pneumotoxic dust (crystalline silica), or a vehicle control (saline). Bronchoalveolar lavage (BAL) was performed 1, 7, 14, and 35 days postinstillation, and indicators of pulmonary damage [cellular differential, albumin, as well as, tumor necrosis factor-alpha (TNF-alpha), interleukin-1 beta (IL-1 beta), lactate dehydrogenase, and beta-n-acetyl glucosaminidase release] were assessed. One day postinstillation, some evidence of lung inflammation (more neutrophils) was observed for all particle groups, while increased BAL TNF-alpha and IL-1 beta were observed only in the SS-SPRAY and silica groups. By 14 days, lungs appeared normal among the MS-SPRAY, MS-PULSE, and iron oxide groups. At 14 and 35 days postinstillation, elevated pulmonary responses persisted for the animals exposed to silica and the SS-SPRAY welding fume. By 35 days, however, the SS-SPRAY group approached control levels, while the injury induced by silica increased. Using magnetometric estimates of welding fumes, we observed that MS-SPRAY fume was cleared from the lungs at a faster rate than the SS-SPRAY particles. We have demonstrated that the SS-SPRAY fume has more pneumotoxicity than MS fumes. This difference may reflect a greater retention of the SS-SPRAY particles in the lungs and different elemental composition of the fume. The SS-SPRAY fume also had enhanced release of TNF-alpha and IL-1 beta from lung cells soon after fume instillation. In contrast, we saw no influence of the power supply on particle size, composition, or toxicity.

Sand fly feeding on noxious plants: a potential method for the control of leishmaniasis.

PubMed

Schlein, Y; Jacobson, R L; Müller, G C

2001-10-01

The sand fly Phlebotomus papatasi transmits Leishmania major, which causes cutaneous leishmaniasis, in vast regions of the Old World. In addition to blood, the sand flies feed on plants. In a study of this diet, we observed that one night of feeding on branches of Solanum jasminoides, Ricinus communis, or Bougainvillea glabra drastically shortened the life span of the sand flies. Flowering B. glabra attracted P. papatasi in the field. Nevertheless, in the region endemic for L. major in yards abounding with vector sand flies, the number of P. papatasi trapped near hedges of B. glabra was eight times less (62 versus 502 flies trapped) than in the control sites. The results imply that B. glabra affords local protection against sand fly bites and decreases the risk of leishmaniasis. We suggest that this and other ornamental plants that are harmful to sand flies can be used as a tool for this purpose.

Hydrogels containing redispersible spray-dried melatonin-loaded nanocapsules: a formulation for transdermal-controlled delivery

NASA Astrophysics Data System (ADS)

Hoffmeister, Cristiane RD; Durli, Taís L.; Schaffazick, Scheila R.; Raffin, Renata P.; Bender, Eduardo A.; Beck, Ruy CR; Pohlmann, Adriana R.; Guterres, Sílvia S.

2012-05-01

The aim of the present study was to develop a transdermal system for controlled delivery of melatonin combining three strategies: nanoencapsulation of melatonin, drying of melatonin-loaded nanocapsules, and incorporation of nanocapsules in a hydrophilic gel. Nanocapsules were prepared by interfacial deposition of the polymer and were spray-dried using water-soluble excipients. In vitro drug release profiles were evaluated by the dialysis bag method, and skin permeation studies were carried out using Franz cells with porcine skin as the membrane. The use of 10% ( w/ v) water-soluble excipients (lactose or maltodextrin) as spray-drying adjuvants furnished redispersible powders (redispersibility index approximately 1.0) suitable for incorporation into hydrogels. All formulations showed a better controlled in vitro release of melatonin compared with the melatonin solution. The best controlled release results were achieved with hydrogels prepared with dried nanocapsules (hydrogels > redispersed dried nanocapsules > nanocapsule suspension > melatonin solution). The skin permeation studies demonstrated a significant modulation of the transdermal melatonin permeation for hydrogels prepared with redispersible nanocapsules. In this way, the additive effect of the different approaches used in this study (nanoencapsulation, spray-drying, and preparation of semisolid dosage forms) allows not only the control of melatonin release, but also transdermal permeation.

Dramatic Decrease in Malaria Transmission after Large-Scale Indoor Residual Spraying with Bendiocarb in Benin, an Area of High Resistance of Anopheles gambiae to Pyrethroids

PubMed Central

Akogbeto, Martin; Padonou, Gil Germain; Bankole, Honore Sourou; Gazard, Dorothee Kinde; Gbedjissi, Ghelus Louis

2011-01-01

In 2008, the National Malaria Control Program in Benin implemented a vector control intervention based on indoor residual spraying (IRS). Four districts of high resistance of Anopheles gambiae to pyrethroids were sprayed with bendiocarb. More than 350,000 inhabitants have been protected. Entomologic parameters in the control area were compared with those in intervention sites. The study has shown a drastic decrease in the An. gambiae biting rate in the sprayed areas. Results of an enzyme-linked immunosorbent assay were negative for Plasmodium falciparum antigen during the entire period of the intervention. No household members received infected bites (entomologic inoculation rate = 0 during January–July). Parous rates were low in areas covered by IRS because bendiocarb is not conducive to long-term mosquito survival. Bendiocarb was found to be a good alternative insecticide for IRS in Benin, in areas where An. gambiae has developed high resistance to pyrethroids. PMID:21976555

Microencapsulation of Lactobacillus acidophilus NCIMB 701748 in matrices containing soluble fibre by spray drying: Technological characterization, storage stability and survival after in vitro digestion☆

PubMed Central

Yonekura, Lina; Sun, Han; Soukoulis, Christos; Fisk, Ian

2014-01-01

We evaluated sodium alginate, chitosan and hydroxypropyl methylcellulose (HPMC) as co-encapsulants for spray dried Lactobacillus acidophilus NCIMB 701748 by assessing their impact on cell viability and physicochemical properties of the dried powders, viability over 35 days of storage at 25 °C and survival after simulated digestion. Fibres were added to a control carrier medium containing whey protein concentrate, d-glucose and maltodextrin. Sodium alginate and HPMC did not affect cell viability but chitosan reduced viable counts in spray dried powders, as compared to the control. Although chitosan caused large losses of viability during spray-drying, these losses were counteracted by the excellent storage stability compared to control, sodium alginate and HPMC, and the overall effect became positive after the 35-day storage. Chitosan also improved survival rates in simulated GI conditions, however no single fibre could improve L. acidophilus NCIMB 701748 viability in all steps from production through storage and digestion. PMID:24748900

Dynamics of flare sprays. [in sun

NASA Technical Reports Server (NTRS)

Tandberg-Hanssen, E.; Martin, S. F.; Hansen, R. T.

1980-01-01

During solar cycle No. 20 new insight into the flare-spray phenomenon has been attained due to several innovations in solar optical-observing techniques (higher spatial resolution cinema-photography, tunable passband filters, multislit spectroscopy and extended angular field coronagraphs). From combined analysis of 13 well-observed sprays which occurred between 1969-1974 it is concluded that (1) the spray material originates from a preexisting active region filament which undergoes increased absorption some tens of minutes prior to the abrupt chromospheric brightening at the 'flare-start', and (2) the spray material is confined within a steadily expanding, loop-shaped (presumable magnetically controlled) envelope with part of the materials draining back down along one or both legs of the loop.

Results of NASA's First Autonomous Formation Flying Experiment: Earth Observing-1 (EO-1)

NASA Technical Reports Server (NTRS)

Folta, David C.; Hawkins, Albin; Bauer, Frank H. (Technical Monitor)

2001-01-01

NASA's first autonomous formation flying mission completed its primary goal of demonstrating an advanced technology called enhanced formation flying. To enable this technology, the Guidance, Navigation, and Control center at the Goddard Space Flight Center (GSFC) implemented a universal 3-axis formation flying algorithm in an autonomous executive flight code onboard the New Millennium Program's (NMP) Earth Observing-1 (EO-1) spacecraft. This paper describes the mathematical background of the autonomous formation flying algorithm and the onboard flight design and presents the validation results of this unique system. Results from functionality assessment through fully autonomous maneuver control are presented as comparisons between the onboard EO-1 operational autonomous control system called AutoCon(tm), its ground-based predecessor, and a standalone algorithm.

Salivary pH after a glucose rinse: effect of a new mucoadhesive spray (Cariex) based on sodium bicarbonate and xylitol.

PubMed

Abbate, G M; Levrini, L; Caria, M P

2014-01-01

This study evaluated whether sodium bicarbonate applied on the oral mucosa through a new mucoadhesive spray (Cariex) could control a drop in salivary pH after a glucose rinse, and therefore enhance the buffering potential of saliva. A sample of 50 healthy adults was selected. At day 1, the measurement of salivary pH was performed in the lower fornix in correspondence with the lower molars. Each subject rinsed with 10 ml of a 10% glucose solution and then pH was monitored continually for 40 minutes. At day 2, the same experimental procedure was repeated and three shots of the spray were administered on the oral mucosa. The tested spray is composed of sodium bicarbonate, xylitol, and excipients. Without the mucoadhesive spray, salivary pH became significantly lower following the glucose rinse (p < 0.01). Following the spray, the time in which the pH remained lower than 6.0 was reduced statistically significantly (p < 0.01). A continual rise of salivary pH was observed for the 40 minutes in which the pH recording was performed. Conclusions: The use of a sodium bicarbonate spray on the mucosa was shown to control the lowering of salivary pH following carbohydrate consumption, and might therefore add to the prevention of caries and dental erosion.

21 CFR 524.2482 - Triamcinolone spray.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Amount. Apply sufficient pump sprays to uniformly and thoroughly wet the affected areas while avoiding... other day for an additional 14 days (28 days total). (2) Indications for use. For the control of...

21 CFR 524.2482 - Triamcinolone spray.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Amount. Apply sufficient pump sprays to uniformly and thoroughly wet the affected areas while avoiding... other day for an additional 14 days (28 days total). (2) Indications for use. For the control of...

Pore Structure Characterization in Concrete Prepared with Carbonated Fly Ash

NASA Astrophysics Data System (ADS)

Sahoo, Sanjukta

2018-03-01

Carbon dioxide capture and storage (CCS) is a technique to address the global concern of continuously rising CO2 level in the atmosphere. Fly ash is considered as a suitable medium for CCS due to presence of metal oxides. The fly ash which has already sequestered carbon dioxide is referred to as carbonated fly ash. Recent research reveals better durability of concretes using carbonated fly ash as part replacement of cement. In the present research pore structure characterization of the carbonated fly ash concrete has been carried out. Mercury Intrusion porosimetry test has been conducted on control concrete and concrete specimens using fly ash and carbonated fly ash at replacement levels of 25% and 40%. The specimens have been water cured for 28 days and 90 days. It is observed that porosity reduction rate is more pronounced in carbonated fly ash concrete compared to control concrete at higher water curing age. Correlation analysis is also carried out which indicates moderately linear relationship between porosity % and pore distribution with particle size and water curing.

The global repressor FliZ antagonizes gene expression by σS-containing RNA polymerase due to overlapping DNA binding specificity.

PubMed

Pesavento, Christina; Hengge, Regine

2012-06-01

FliZ, a global regulatory protein under the control of the flagellar master regulator FlhDC, was shown to antagonize σ(S)-dependent gene expression in Escherichia coli. Thereby it plays a pivotal role in the decision between alternative life-styles, i.e. FlhDC-controlled flagellum-based motility or σ(S)-dependent curli fimbriae-mediated adhesion and biofilm formation. Here, we show that FliZ is an abundant DNA-binding protein that inhibits gene expression mediated by σ(S) by recognizing operator sequences that resemble the -10 region of σ(S)-dependent promoters. FliZ does so with a structural element that is similar to region 3.0 of σ(S). Within this element, R108 in FliZ corresponds to K173 in σ(S), which contacts a conserved cytosine at the -13 promoter position that is specific for σ(S)-dependent promoters. R108 as well as C(-13) are also crucial for DNA binding by FliZ. However, while a number of FliZ binding sites correspond to known σ(S)-dependent promoters, promoter activity is not a prerequisite for FliZ binding and repressor function. Thus, we demonstrate that FliZ also feedback-controls flagellar gene expression by binding to a site in the flhDC control region that shows similarity only to a -10 element of a σ(S)-dependent promoter, but does not function as a promoter.

House fly (Musca domestica) (Diptera: Muscidae) mortality after exposure to commercial fungal formulations in a sugar bait

USDA-ARS?s Scientific Manuscript database

House flies (Musca domestica L.) (Diptera: Muscidae) are major pests of livestock. Biological control is an important tool in an integrated control framework. Increased mortality in filth flies has been documented with entomopathogenic fungi, and several strains are commercially available. Three str...

Recent progress in a classical biological control program for olive fruit fly in California

USDA-ARS?s Scientific Manuscript database

The olive fruit fly, Bactrocera oleae (Diptera: Tephritidae), causes severe damage to olive production worldwide. Control of olive fruit fly typically relies on pesticides, and under such conditions the impact of natural enemies is relatively low. About 15 years ago, the USDA-ARS European Biologic...

Flying Drosophila stabilize their vision-based velocity controller by sensing wind with their antennae

PubMed Central

Fuller, Sawyer Buckminster; Straw, Andrew D.; Peek, Martin Y.; Murray, Richard M.; Dickinson, Michael H.

2014-01-01

Flies and other insects use vision to regulate their groundspeed in flight, enabling them to fly in varying wind conditions. Compared with mechanosensory modalities, however, vision requires a long processing delay (~100 ms) that might introduce instability if operated at high gain. Flies also sense air motion with their antennae, but how this is used in flight control is unknown. We manipulated the antennal function of fruit flies by ablating their aristae, forcing them to rely on vision alone to regulate groundspeed. Arista-ablated flies in flight exhibited significantly greater groundspeed variability than intact flies. We then subjected them to a series of controlled impulsive wind gusts delivered by an air piston and experimentally manipulated antennae and visual feedback. The results show that an antenna-mediated response alters wing motion to cause flies to accelerate in the same direction as the gust. This response opposes flying into a headwind, but flies regularly fly upwind. To resolve this discrepancy, we obtained a dynamic model of the fly’s velocity regulator by fitting parameters of candidate models to our experimental data. The model suggests that the groundspeed variability of arista-ablated flies is the result of unstable feedback oscillations caused by the delay and high gain of visual feedback. The antenna response drives active damping with a shorter delay (~20 ms) to stabilize this regulator, in exchange for increasing the effect of rapid wind disturbances. This provides insight into flies’ multimodal sensory feedback architecture and constitutes a previously unknown role for the antennae. PMID:24639532

Visual control of flight speed in Drosophila melanogaster.

PubMed

Fry, Steven N; Rohrseitz, Nicola; Straw, Andrew D; Dickinson, Michael H

2009-04-01

Flight control in insects depends on self-induced image motion (optic flow), which the visual system must process to generate appropriate corrective steering maneuvers. Classic experiments in tethered insects applied rigorous system identification techniques for the analysis of turning reactions in the presence of rotating pattern stimuli delivered in open-loop. However, the functional relevance of these measurements for visual free-flight control remains equivocal due to the largely unknown effects of the highly constrained experimental conditions. To perform a systems analysis of the visual flight speed response under free-flight conditions, we implemented a 'one-parameter open-loop' paradigm using 'TrackFly' in a wind tunnel equipped with real-time tracking and virtual reality display technology. Upwind flying flies were stimulated with sine gratings of varying temporal and spatial frequencies, and the resulting speed responses were measured from the resulting flight speed reactions. To control flight speed, the visual system of the fruit fly extracts linear pattern velocity robustly over a broad range of spatio-temporal frequencies. The speed signal is used for a proportional control of flight speed within locomotor limits. The extraction of pattern velocity over a broad spatio-temporal frequency range may require more sophisticated motion processing mechanisms than those identified in flies so far. In Drosophila, the neuromotor pathways underlying flight speed control may be suitably explored by applying advanced genetic techniques, for which our data can serve as a baseline. Finally, the high-level control principles identified in the fly can be meaningfully transferred into a robotic context, such as for the robust and efficient control of autonomous flying micro air vehicles.

A pilot's assessment of helicopter handling-quality factors common to both agility and instrument flying tasks

NASA Technical Reports Server (NTRS)

Gerdes, R. M.

1980-01-01

A series of simulation and flight investigations were undertaken to evaluate helicopter flying qualities and the effects of control system augmentation for nap-of-the-Earth (NOE) agility and instrument flying tasks. Handling quality factors common to both tasks were identified. Precise attitude control was determined to be a key requirement for successful accomplishment of both tasks. Factors that degraded attitude controllability were improper levels of control sensitivity and damping, and rotor system cross coupling due to helicopter angular rate and collective pitch input. Application of rate command, attitude command, and control input decouple augmentation schemes enhanced attitude control and significantly improved handling qualities for both tasks. The NOE agility and instrument flying handling quality considerations, pilot rating philosophy, and supplemental flight evaluations are also discussed.

Flying qualities - A costly lapse in flight-control design

NASA Technical Reports Server (NTRS)

Berry, D. T.

1982-01-01

Generic problems in advanced aircraft with advanced control systems which suffer from control sensitivity, sluggish response, and pilot-induced oscillation tendencies are examined, with a view to improving techniques for eliminating the problems in the design phase. Results of two NASA and NASA/AIAA workshops reached a consensus that flying qualities criteria do not match control system development, control system designers are not relying on past experience in their field, ground-based simulation is relied on too heavily, and communications between flying qualities and control systems engineers need improvement. A summation is offered in that hardware and software have outstripped the pilot's capacity to use the capabilities which new aircraft offer. The flying qualities data base is stressed to be dynamic, and continually redefining the man/machine relationships.

How Much Does Malaria Vector Control Quality Matter: The Epidemiological Impact of Holed Nets and Inadequate Indoor Residual Spraying

PubMed Central

Rehman, Andrea M.; Coleman, Mike; Schwabe, Christopher; Baltazar, Giovanna; Matias, Abrahan; Roncon Gomes, Irina; Yellott, Lee; Aragon, Cynthia; Nseng Nchama, Gloria; Mzilahowa, Themba; Rowland, Mark; Kleinschmidt, Immo

2011-01-01

Background Insecticide treated nets (ITN) and indoor residual spraying (IRS) are the two pillars of malaria vector control in Africa, but both interventions are beset by quality and coverage concerns. Data from three control programs were used to investigate the impact of: 1) the physical deterioration of ITNs, and 2) inadequate IRS spray coverage, on their respective protective effectiveness. Methods Malaria indicator surveys were carried out in 2009 and 2010 in Bioko Island, mainland Equatorial Guinea and Malawi to monitor infection with P.falciparum in children, mosquito net use, net condition and spray status of houses. Nets were classified by their condition. The association between infection and quality and coverage of interventions was investigated. Results There was reduced odds of infection with P.falciparum in children sleeping under ITNs that were intact (Odds ratio (OR): 0.65, 95% CI: 0.55–0.77 and OR: 0.81, 95% CI: 0.56–1.18 in Equatorial Guinea and in Malawi respectively), but the protective effect became less with increasingly worse condition of the net. There was evidence for a linear trend in infection per category increase in deterioration of nets. In Equatorial Guinea IRS offered protection to those in sprayed and unsprayed houses alike when neighbourhood spray coverage was high (≥80%) compared to those living in areas of low IRS coverage (<20%), regardless of whether the house they lived in was sprayed or not (adjusted OR = 0.54, 95% CI 0.33–0.89). ITNs provided only personal protection, offering no protection to non users. Although similar effects were seen in Malawi, the evidence was much weaker than in Equatorial Guinea. Conclusions Universal coverage strategies should consider policies for repair and replacement of holed nets and promote the care of nets by their owners. IRS programs should ensure high spray coverage since inadequate coverage gives little or no protection at all. PMID:21559436

Agricultural Animal Pest Control. Bulletin 767.

ERIC Educational Resources Information Center

Nolan, Maxcy P., Jr.

Included in this training manual are descriptions and pictures of the following agricultural animal pests: mosquitoes, stable flies, horse flies and deer or yellow flies, house flies, horn flies, wound-infesting larvae, lice, mites, ticks, and bots and grubs. Information is given on the life-cycle and breeding habits of the pests. Methods of…

Botanically-based repellent and insecticidal effects against horn flies, Haematobia irritans irritans (L.), and stable flies, Stomoxys calcitrans (L.) (Dipera: Muscidae)

USDA-ARS?s Scientific Manuscript database

Horn flies, Haematobia irritans irritans (L.) and stable flies, Stomoxys calcitrans (L.) (Diptera: Muscidae), are economically important blood-feeding ectoparasites of cattle, Bos taurus L., and other domesticated and wild animals. Conventional insecticides are used for control of biting flies on ca...

SPHERES Facility

NASA Technical Reports Server (NTRS)

Martinez, Andres; Benavides, Jose Victor; Ormsby, Steve L.; GuarnerosLuna, Ali

2014-01-01

Synchronized Position Hold, Engage, Reorient, Experimental Satellites (SPHERES) are bowling-ball sized satellites that provide a test bed for development and research into multi-body formation flying, multi-spacecraft control algorithms, and free-flying physical and material science investigations. Up to three self-contained free-flying satellites can fly within the cabin of the International Space Station (ISS), performing flight formations, testing of control algorithms or as a platform for investigations requiring this unique free-flying test environment. Each satellite is a self-contained unit with power, propulsion, computers, navigation equipment, and provides physical and electrical connections (via standardized expansion ports) for Principal Investigator (PI) provided hardware and sensors.

Optimization of Control Strategies for Non-Domiciliated Triatoma dimidiata, Chagas Disease Vector in the Yucatán Peninsula, Mexico

PubMed Central

Barbu, Corentin; Dumonteil, Eric; Gourbière, Sébastien

2009-01-01

Background Chagas disease is the most important vector-borne disease in Latin America. Regional initiatives based on residual insecticide spraying have successfully controlled domiciliated vectors in many regions. Non-domiciliated vectors remain responsible for a significant transmission risk, and their control is now a key challenge for disease control. Methodology/Principal Findings A mathematical model was developed to predict the temporal variations in abundance of non-domiciliated vectors inside houses. Demographic parameters were estimated by fitting the model to two years of field data from the Yucatan peninsula, Mexico. The predictive value of the model was tested on an independent data set before simulations examined the efficacy of control strategies based on residual insecticide spraying, insect screens, and bednets. The model accurately fitted and predicted field data in the absence and presence of insecticide spraying. Pyrethroid spraying was found effective when 50 mg/m2 were applied yearly within a two-month period matching the immigration season. The >80% reduction in bug abundance was not improved by larger doses or more frequent interventions, and it decreased drastically for different timing and lower frequencies of intervention. Alternatively, the use of insect screens consistently reduced bug abundance proportionally to the reduction of the vector immigration rate. Conclusion/Significance Control of non-domiciliated vectors can hardly be achieved by insecticide spraying, because it would require yearly application and an accurate understanding of the temporal pattern of immigration. Insect screens appear to offer an effective and sustainable alternative, which may be part of multi-disease interventions for the integrated control of neglected vector-borne diseases. PMID:19365542

Analysis of wind-tunnel stability and control tests in terms of flying qualities of full-scale airplanes

NASA Technical Reports Server (NTRS)

Kayten, Gerald G

1945-01-01

The analysis of results of wind-tunnel stability and control tests of powered airplane models in terms of the flying qualities of full-scale airplanes is advocated. In order to indicated the topics upon which comments are considered desirable in the report of a wind-tunnel stability and control investigation and to demonstrate the nature of the suggested analysis, the present NACA flying-qualities requirements are discussed in relation to wind-tunnel tests. General procedures for the estimation of flying qualities from wind-tunnel tests are outlined.

Petition to the Environmental Protection Agency to Control Asbestos Emmissions from Spray-On Materials Which Have Been Applied in Public School Buildings for Insulation, Fireproofing, Decorative or Other Purposes.

ERIC Educational Resources Information Center

Environmental Defense Fund, Washington, DC.

This petition requests the Environmental Protection Agency to promulgate regulations in compliance with section 6 of the Toxic Substances Control Act to control asbestos emissions from spray-on materials containing 1 percent or more asbestos that has been applied in public school buildings for insulation, fireproofing, decorative, or other…

Insect Pests of Shade Trees and Shrubs: A Guide for Commercial Nurserymen and Arborists. Publication E-41.

ERIC Educational Resources Information Center

Schuder, Donald L.

This guide presents information on controlling insect pests of ornamental trees and shrubs. It is organized for easy reference by nurserymen, arborists, and others desirous of controlling insect damage. General information given includes notes on spraying and sprayers, insecticides, general purpose sprays, phytotoxicity, and health precautions.…

Spray penetration and natural enemy survival in dense and sparse plant canopies treated with Carbaryl: implications for conventional and biological control

USDA-ARS?s Scientific Manuscript database

Ornamental plant producers often rely on chemical control to manage insect pests. However, cultural practices, such as pruning, can influence plant architecture which may, in turn, affect pesticide penetration. Spray penetration was studied to determine the effect of canopy density on beneficial ins...

Probe-Substrate Distance Control in Desorption Electrospray Ionization

NASA Astrophysics Data System (ADS)

Yarger, Tyler J.; Yuill, Elizabeth M.; Baker, Lane A.

2018-03-01

We introduce probe-substrate distance (Dps)-control to desorption electrospray ionization (DESI) and report a systematic investigation of key experimental parameters. Examination of voltage, flow rate, and nebulizing gas pressure suggests as Dps decreases, the distance-dependent spray current increases, until a critical point. At the critical point the relationship inverts, and the spray current decreases as the probe moves closer to the surface due to constriction of solution flow by the nebulizing gas. Dps control was used to explore the use of spray current as a signal for feedback positioning, while mass spectrometry imaging was performed simultaneously. Further development of this technique is expected to find application in study of structure-function relationships for clinical diagnostics, biological investigation, and materials characterization. [Figure not available: see fulltext.

Context-dependent olfactory enhancement of optomotor flight control in Drosophila.

PubMed

Chow, Dawnis M; Frye, Mark A

2008-08-01

Sensing and following the chemical plume of food odors is a fundamental challenge faced by many organisms. For flying insects, the task is complicated by wind that distorts the plume and buffets the fly. To maintain an upwind heading, and thus stabilize their orientation in a plume, insects such as flies and moths make use of strong context-specific visual equilibrium reflexes. For example, flying straight requires the regulation of image rotation across the eye, whereas minimizing side-slip and avoiding a collision require regulation of image expansion. In flies, visual rotation stabilizes plume tracking, but rotation and expansion optomotor responses are controlled by separate visual pathways. Are olfactory signals integrated with optomotor responses in a manner dependent upon visual context? We addressed this question by investigating the effect of an attractive food odor on active optomotor flight control. Odorant caused flies both to increase aerodynamic power output and to steer straighter. However, when challenged with wide-field optic flow, odor resulted in enhanced amplitude rotation responses but reduced amplitude expansion responses. For both visual conditions, flies tracked motion signals more closely in odor, an indication of increased saliency. These results suggest a simple search algorithm by which olfactory signals improve the salience of visual stimuli and modify optomotor control in a context-dependent manner, thereby enabling an animal to fly straight up a plume and approach odiferous objects.

Spray droplet size, drift potential, and risks to nontarget organisms from aerially applied glyphosate for coca control in Colombia.

PubMed

Hewitt, Andrew J; Solomon, Keith R; Marshall, E J P

2009-01-01

A wind tunnel atomization study was conducted to measure the emission droplet size spectra for water and Glyphos (a glyphosate formulation sold in Colombia) + Cosmo-flux sprays for aerial application to control coca and poppy crops in Colombia. The droplet size spectra were measured in a wind tunnel for an Accu-Flo nozzle (with 16 size 0.085 [2.16 mm] orifices), under appropriate simulated aircraft speeds (up to 333 km/h), using a laser diffraction instrument covering a dynamic size range for droplets of 0.5 to 3,500 microm. The spray drift potential of the glyphosate was modeled using the AGDISP spray application and drift model, using input parameters representative of those occurring in Colombia for typical aerial application operations. The droplet size spectra for tank mixes containing glyphosate and Cosmo-Flux were considerably finer than water and became finer with higher aircraft speeds. The tank mix with 44% glyphosate had a D(v0.5) of 128 microm, while the value at the 4.9% glyphosate rate was 140 microm. These are classified as very fine to fine sprays. Despite being relatively fine, modeling showed that the droplets would not evaporate as rapidly as most similarly sized agricultural sprays because the nonvolatile proportion of the tank mix (active and inert adjuvant ingredients) was large. Thus, longer range drift is small and most drift that does occur will deposit relatively close to the application area. Drift will only occur downwind and, with winds of velocity less than the modeled maximum of 9 km/h, the drift distance would be substantially reduced. Spray drift potential might be additionally reduced through various practices such as the selection of nozzles, tank mix adjuvants, aircraft speeds, and spray pressures that would produce coarser sprays. Species sensitivity distributions to glyphosate were constructed for plants and amphibians. Based on modeled drift and 5th centile concentrations, appropriate no-spray buffer zones (distance from the end of the spray boom as recorded electronically +/-5%) for protection of sensitive plants were 50-120 m for coca spray scenarios and considerably lower for poppy spray scenarios. The equivalent buffer zone for amphibia was 5 m. The low toxicity of glyphosate to humans suggests that these aerial applications are not a concern for human health.

Macroscale and Nanoscale Morphology Evolution during in Situ Spray Coating of Titania Films for Perovskite Solar Cells.

PubMed

Su, Bo; Caller-Guzman, Herbert A; Körstgens, Volker; Rui, Yichuan; Yao, Yuan; Saxena, Nitin; Santoro, Gonzalo; Roth, Stephan V; Müller-Buschbaum, Peter

2017-12-20

Mesoporous titania is a cheap and widely used material for photovoltaic applications. To enable a large-scale fabrication and a controllable pore size, we combined a block copolymer-assisted sol-gel route with spray coating to fabricate titania films, in which the block copolymer polystyrene-block-poly(ethylene oxide) (PS-b-PEO) is used as a structure-directing template. Both the macroscale and nanoscale are studied. The kinetics and thermodynamics of the spray deposition processes are simulated on a macroscale, which shows a good agreement with the large-scale morphology of the spray-coated films obtained in practice. On the nanoscale, the structure evolution of the titania films is probed with in situ grazing incidence small-angle X-ray scattering (GISAXS) during the spray process. The changes of the PS domain size depend not only on micellization but also on solvent evaporation during the spray coating. Perovskite (CH 3 NH 3 PbI 3 ) solar cells (PSCs) based on sprayed titania film are fabricated, which showcases the suitability of spray-deposited titania films for PSCs.

Thermal Arc Spray Overview

NASA Astrophysics Data System (ADS)

Hafiz Abd Malek, Muhamad; Hayati Saad, Nor; Kiyai Abas, Sunhaji; Mohd Shah, Noriyati

2013-06-01

Usage of protective coating for corrosion protection was on highly demand during the past decade; and thermal spray coating played a major part during that time. In recent years, the thermal arc spray coating becomes a popular coating. Many big players in oil and gas such as PETRONAS, EXXON MOBIL and SHELL in Malaysia tend to use the coating on steel structure as a corrosion protection. Further developments in coating processes, the devices, and raw materials have led to expansion of functional coatings and applications scope from conventional coating to specialized industries. It is widely used because of its ability to withstand high process temperature, offer advantages in efficiency, lower cost and acts as a corrosion protection. Previous research also indicated that the thermal arc spray offers better coating properties compared to other methods of spray. This paper reviews some critical area of thermal spray coating by discussing the process/parameter of thermal arc spray technology and quality control of coating. Coating performance against corrosion, wear and special characteristic of coating are also described. The field application of arc spray technology are demonstrated and reviewed.

Evaluation of Fly Ash Quality Control Tools

DOT National Transportation Integrated Search

2010-06-30

Many entities currently use fly ash in portland cement concrete (PCC) pavements and structures. Although the body of knowledge is : great concerning the use of fly ash, several projects per year are subject to poor performance where fly ash is named ...

Evaluation of fly ash quality control tools.

DOT National Transportation Integrated Search

2010-06-30

Many entities currently use fly ash in portland cement concrete (PCC) pavements and structures. Although the body of knowledge is : great concerning the use of fly ash, several projects per year are subject to poor performance where fly ash is named ...

Drosophila mushroom bodies integrate hunger and satiety signals to control innate food-seeking behavior.

PubMed

Tsao, Chang-Hui; Chen, Chien-Chun; Lin, Chen-Han; Yang, Hao-Yu; Lin, Suewei

2018-03-16

The fruit fly can evaluate its energy state and decide whether to pursue food-related cues. Here, we reveal that the mushroom body (MB) integrates hunger and satiety signals to control food-seeking behavior. We have discovered five pathways in the MB essential for hungry flies to locate and approach food. Blocking the MB-intrinsic Kenyon cells (KCs) and the MB output neurons (MBONs) in these pathways impairs food-seeking behavior. Starvation bi-directionally modulates MBON responses to a food odor, suggesting that hunger and satiety controls occur at the KC-to-MBON synapses. These controls are mediated by six types of dopaminergic neurons (DANs). By manipulating these DANs, we could inhibit food-seeking behavior in hungry flies or promote food seeking in fed flies. Finally, we show that the DANs potentially receive multiple inputs of hunger and satiety signals. This work demonstrates an information-rich central circuit in the fly brain that controls hunger-driven food-seeking behavior. © 2018, Tsao et al.

Optimal boiler control through real-time monitoring of unburned carbon in fly ash by laser-induced breakdown spectroscopy.

PubMed

Kurihara, Miki; Ikeda, Koji; Izawa, Yoshinori; Deguchi, Yoshihiro; Tarui, Hitoshi

2003-10-20

A laser-induced breakdown spectroscopy (LIBS) technique has been applied for detection of unburned carbon in fly ash, and an automated LIBS unit has been developed and applied in a 1000-MW pulverized-coal-fired power plant for real-time measurement, specifically of unburned carbon in fly ash. Good agreement was found between measurement results from the LIBS method and those from the conventional method (Japanese Industrial Standard 8815), with a standard deviation of 0.27%. This result confirms that the measurement of unburned carbon in fly ash by use of LIBS is sufficiently accurate for boiler control. Measurements taken by this apparatus were also integrated into a boiler-control system with the objective of achieving optimal and stable combustion. By control of the rotating speed of a mill rotary separator relative to measured unburned-carbon content, it has been demonstrated that boiler control is possible in an optimized manner by use of the value of the unburned-carbon content of fly ash.

Drosophila mushroom bodies integrate hunger and satiety signals to control innate food-seeking behavior

PubMed Central

Tsao, Chang-Hui; Chen, Chien-Chun; Lin, Chen-Han; Yang, Hao-Yu

2018-01-01

The fruit fly can evaluate its energy state and decide whether to pursue food-related cues. Here, we reveal that the mushroom body (MB) integrates hunger and satiety signals to control food-seeking behavior. We have discovered five pathways in the MB essential for hungry flies to locate and approach food. Blocking the MB-intrinsic Kenyon cells (KCs) and the MB output neurons (MBONs) in these pathways impairs food-seeking behavior. Starvation bi-directionally modulates MBON responses to a food odor, suggesting that hunger and satiety controls occur at the KC-to-MBON synapses. These controls are mediated by six types of dopaminergic neurons (DANs). By manipulating these DANs, we could inhibit food-seeking behavior in hungry flies or promote food seeking in fed flies. Finally, we show that the DANs potentially receive multiple inputs of hunger and satiety signals. This work demonstrates an information-rich central circuit in the fly brain that controls hunger-driven food-seeking behavior. PMID:29547121

The impact of insecticide-treated material to reduce flies among pork outlets in Kampala, Uganda.

PubMed

Heilmann, Martin; Roesel, Kristina; Grace, Delia; Bauer, Burkhard; Clausen, Peter-Henning

2017-06-01

Synanthropic flies have adapted to the mass of decaying organic matter near human settlements. As such, they feed and breed on food, faeces and other organic material and are known vectors for various diseases. Many of these diseases are associated with food, and foodborne diseases are of growing concern in developing countries where human population and food consumption increase. This pilot study aims at investigating the impact of a novel application of insecticide-treated material (ZeroFly®) to reduce flies among pork outlets in Kampala, Uganda. A cross-sectional survey randomly selected 60 of 179 pork outlets in Kampala. A controlled longitudinal trial followed in which 23 out of the 60 pork outlets were recruited for an intervention with insecticide-treated material. The pork outlets were randomly allocated to a group of 18 netted pork outlets (intervention) and five non-netted pork outlets (control). Monitoring took place over 15 weeks including 2 weeks as the baseline survey. The units were monitored for fly abundance using non-attractant sticky traps, which were placed within the pork outlet once per week for 48 consecutive hours. Medians of fly numbers before and after the intervention indicated a decrease of fly numbers of 48% (p = 0.002). Fly bioassays showed that the insecticidal activity of the netting remained active over the entire intervention period and led to a total paralysis of flies within at least 6 h after exposure. Insecticide-treated material provides a practical and sustainable solution in controlling flies and is therefore recommended as a complementary strategy for an integrated vector control and hygiene management.

Effects Sprayed Solution of Salicylic Acid to Prevent of Wilt Disease Caused by Fussarium oxysporium

NASA Astrophysics Data System (ADS)

Yousif, Dina. Y. M.

2018-05-01

The current search aimed to detective the effect of sprayed solution of salicylic acid on plant and leaves of sweet green pepper (Capsicum annuum) for control the pathogen Fussarium oxysporium compering with control plant and leaves. Results indicated that, the spray of salicylic acid at concentration 0.5 g/L is effecting the fungal infection through prevent transport fungus F. oxysporum to the neighboring green pepper plant. The number of dead green pepper plant after sprayed with solution of salicylic acid and only water they were (4, 6, and 3) (8, 9, and 10) respectively. While the experimental infection of green pepper leaves after inoculated the fungus as local spot by scorching small spots of these leaves with the aid of hot nail. These spots were then exposed to the 0.5 g/L aqueous solution salicylic acid before and after the inoculation of the fungus. The spray of salicylic acid before 24 and 48 hour prevent the development of disease and make a good protection of the mention leaves from infection with this fungus, the diameter of leaves lesion (1,1.5 cm) respectively. while the ability of fungus to grow after 24 and 48 hour from salicylic acid treatment was markedly reduce as compared with control, such treatment show slow growth of pathogen infect.

2008 Field Releases of Psyttalia cf. concolor for Biological Control of Olive Fruit Fly in California

USDA-ARS?s Scientific Manuscript database

The parasitoid Psytallia cf. concolor (Szépligeti) was reared on sterile Mediterranean fruit fly larvae at the USDA-APHIS-PPQ, Petapa Quarantine Laboratory in Guatemala and shipped to the USDA-ARS, Parlier for biological control of olive fruit fly, Bactrocera oleae (Gmelin), in California. Improved ...

Attractant-based systems as pesticide alternatives for control of tropical fruit flies (Diptera: Tephritidae)

USDA-ARS?s Scientific Manuscript database

Mass trapping and attract-and-kill bait stations are two attractant based systems that are being used or are under development as pesticide alternatives for control of a number of pest tephritid fruit flies. Results of field trials for suppression of Caribbean fruit flies in guava orchards in Florid...

Biological Control of Olive Fruit Fly in California with a Parasitoid Imported from Guatemala

USDA-ARS?s Scientific Manuscript database

The parasitoid, Psyttalia cf. concolor (Szépligeti), was imported into California from the USDA-APHIS-PPQ, Moscamed, San Miguel Petapa, Guatemala for biological control of olive fruit fly, Bactrocera oleae (Gmelin), in olives, Olea europaea L. The parasitoid did not develop in the seedhead fly, Cha...

Near-net-shape manufacturing: Spray-formed metal matrix composites and tooling

NASA Technical Reports Server (NTRS)

Mchugh, Kevin M.

1994-01-01

Spray forming is a materials processing technology in which a bulk liquid metal is converted to a spray of fine droplets and deposited onto a substrate or pattern to form a near-net-shape solid. The technology offers unique opportunities for simplifying materials processing without sacrificing, and oftentimes substantially improving, product quality. Spray forming can be performed with a wide range of metals and nonmetals, and offers property improvements resulting from rapid solidification (e.g. refined microstructures, extended solid solubilities and reduced segregation). Economic benefits result from process simplification and the elimination of unit operations. The Idaho National Engineering Laboratory is developing a unique spray-forming method, the Controlled Aspiration Process (CAP), to produce near-net-shape solids and coatings of metals, polymers, and composite materials. Results from two spray-accompanying technical and economic benefits. These programs involved spray forming aluminum strip reinforced with SiC particulate, and the production of tooling, such as injection molds and dies, using low-melting-point metals.

Integrated Management of European Cherry Fruit Fly Rhagoletis cerasi (L.): Situation in Switzerland and Europe.

PubMed

Daniel, Claudia; Grunder, Jürg

2012-10-16

The European cherry fruit fly, Rhagoletis cerasi (L.) (Diptera: Tephritidae), is a highly destructive pest. The low tolerance for damaged fruit requires preventive insecticide treatments for a marketable crop. The phase-out of old insecticides threatens cherry production throughout the European Union (EU). Consequently, new management techniques and tools are needed. With the increasing number of dwarf tree orchards covered against rain to avoid fruit splitting, crop netting has become a viable, cost-effective method of cherry fruit fly control. Recently, a biocontrol method using the entomopathogenic fungus Beauveria bassiana has been developed for organic agriculture. However, for most situations, there is still a lack of efficient and environmentally sound insecticides to control this pest. This review summarizes the literature from over one hundred years of research on R. cerasi with focus on the biology and history of cherry fruit fly control as well as on antagonists and potential biocontrol organisms. We will present the situation of cherry fruit fly regulation in different European countries, give recommendations for cherry fruit fly control, show gaps in knowledge and identify future research opportunities.

Integrated Management of European Cherry Fruit Fly Rhagoletis cerasi (L.): Situation in Switzerland and Europe

PubMed Central

Daniel, Claudia; Grunder, Jürg

2012-01-01

The European cherry fruit fly, Rhagoletis cerasi (L.) (Diptera: Tephritidae), is a highly destructive pest. The low tolerance for damaged fruit requires preventive insecticide treatments for a marketable crop. The phase-out of old insecticides threatens cherry production throughout the European Union (EU). Consequently, new management techniques and tools are needed. With the increasing number of dwarf tree orchards covered against rain to avoid fruit splitting, crop netting has become a viable, cost-effective method of cherry fruit fly control. Recently, a biocontrol method using the entomopathogenic fungus Beauveria bassiana has been developed for organic agriculture. However, for most situations, there is still a lack of efficient and environmentally sound insecticides to control this pest. This review summarizes the literature from over one hundred years of research on R. cerasi with focus on the biology and history of cherry fruit fly control as well as on antagonists and potential biocontrol organisms. We will present the situation of cherry fruit fly regulation in different European countries, give recommendations for cherry fruit fly control, show gaps in knowledge and identify future research opportunities. PMID:26466721

Vector control in leishmaniasis.

PubMed

Kishore, K; Kumar, V; Kesari, S; Dinesh, D S; Kumar, A J; Das, P; Bhattacharya, S K

2006-03-01

Indoor residual spraying is a simple and cost effective method of controlling endophilic vectors and DDT remains the insecticide of choice for the control of leishmaniasis. However resistance to insecticide is likely to become more widespread in the population especially in those areas in which insecticide has been used for years. In this context use of slow release emulsified suspension (SRES) may be the best substitute. In this review spraying frequencies of DDT and new schedule of spray have been discussed. Role of biological control and environment management in the control of leishmaniasis has been emphasized. Allethrin (coil) 0.1 and 1.6 per cent prallethrin (liquid) have been found to be effective repellents against Phlebotomus argentipes, the vector of Indian kalaazar. Insecticide impregnated bednets is another area which requires further research on priority basis for the control of leishmaniasis. Role of satellite remote sensing for early prediction of disease by identifying the sandflygenic conditions cannot be undermined. In future synthetic pheromons can be exploited in the control of leishmaniasis.

Interaction of feel system and flight control system dynamics on lateral flying qualities

NASA Technical Reports Server (NTRS)

Bailey, R. E.; Knotts, L. H.

1990-01-01

An experimental investigation of the influence of lateral feel system characteristics on fighter aircraft roll flying qualities was conducted using the variable stability USAF NT-33. Forty-two evaluation flights were flown by three engineering test pilots. The investigation utilized the power approach, visual landing task and up-and-away tasks including formation, gun tracking, and computer-generated compensatory attitude tracking tasks displayed on the Head-Up Display. Experimental variations included the feel system frequency, force-deflection gradient, control system command type (force or position input command), aircraft roll mode time constant, control system prefilter frequency, and control system time delay. The primary data were task performance records and evaluation pilot comments and ratings using the Cooper-Harper scale. The data highlight the unique and powerful effect of the feel system of flying qualities. The data show that the feel system is not 'equivalent' in flying qualities influence to analogous control system elements. A lower limit of allowable feel system frequency appears warranted to ensure good lateral flying qualities. Flying qualities criteria should most properly treat the feel system dynamic influence separately from the control system, since the input and output of this dynamic element is apparent to the pilot and thus, does not produce a 'hidden' effect.

Preliminary Results of NASA's First Autonomous Formation Flying Experiment: Earth Observing-1 (EO-1)

NASA Technical Reports Server (NTRS)

Folta, David; Hawkins, Albin

2001-01-01

NASA's first autonomous formation flying mission is completing a primary goal of demonstrating an advanced technology called enhanced formation flying. To enable this technology, the Guidance, Navigation, and Control center at the Goddard Space Flight Center has implemented an autonomous universal three-axis formation flying algorithm in executive flight code onboard the New Millennium Program's (NMP) Earth Observing-1 (EO-1) spacecraft. This paper describes the mathematical background of the autonomous formation flying algorithm and the onboard design and presents the preliminary validation results of this unique system. Results from functionality assessment and autonomous maneuver control are presented as comparisons between the onboard EO-1 operational autonomous control system called AutoCon(tm), its ground-based predecessor, and a stand-alone algorithm.

Field evaluation of a mechanical fly catcher in the control of houseflies.

PubMed

Tilak, R; Dutta Gupta, K K

2007-01-01

'Fly Catcher', an innovative herbal based mechanical trap was evaluated for its efficacy in reducing fly nuisance in and around messes operating in a large teaching establishment and the adjacent garbage dumps. It is recommended that the 'Fly Catcher' may be used as an adjunct to other routinely followed anti fly measures.

Experimental use of fly ash concrete in prefabricated bridge-deck slabs.

DOT National Transportation Integrated Search

1987-01-01

Hydraulic cement concretes with and without fly ash were investigated to assess the suitability of using fly ash in bridge-deck concrete. Eight prefabricated concrete slabs were prepared: four were control and the remaining contained fly ash. They we...

A pilot's assessment of helicopter handling-quality factors common to both agility and instrument flying tasks

NASA Technical Reports Server (NTRS)

Gerdes, R. M.

1980-01-01

Results from a series of simulation and flight investigations undertaken to evaluate helicopter flying qualities and the effects of control system augmentation for nap-of-the-earth (NOE) agility and instrument flying tasks were analyzed to assess handling-quality factors common to both tasks. Precise attitude control was determined to be a key requirement for successful accomplishment of both tasks. Factors that degraded attitude controllability were improper levels of control sensitivity and damping and rotor-system cross-coupling due to helicopter angular rate and collective pitch input. Application of rate-command, attitude-command, and control-input decouple augmentation schemes enhanced attitude control and significantly improved handling qualities for both tasks. NOE agility and instrument flying handling-quality considerations, pilot rating philosophy, and supplemental flight evaluations are also discussed.

Coal-water slurry sprays from an electronically controlled accumulator fuel injection system: Break-up distances and times

NASA Astrophysics Data System (ADS)

Caton, J. A.; Payne, S. E.; Terracina, D. P.; Kihm, K. D.

Experiments have been completed to characterize coal-water slurry sprays from an electronically-controlled accumulator fuel injection system of a diesel engine. The sprays were injected into a pressurized chamber equipped with windows. High speed movies, fuel pressures, and needle lifts were obtained as a function of time, orifice diameter, coal loading, gas density in the chamber, and accumulator fuel pressure. For the base conditions (50% by mass coal loading, 0.4 mm diameter nozzle hole, coal-water slurry pressure of 82 MPa (12,000 psi), and a chamber density of 25 kg/m(exp 3)), the break-up time was 0.30 ms. An empirical correlation for spray tip penetration, break-up time, and initial jet velocity was developed. For the conditions of this study, the spray tip penetration and initial jet velocity were 15% greater for coal-water slurry than for diesel fuel or water. Results of this study and the correlation are specific to the tested coal-water slurry and are not general for other coal-water slurry fuels.

Effectiveness of a long-lasting piperonyl butoxide-treated insecticidal net and indoor residual spray interventions, separately and together, against malaria transmitted by pyrethroid-resistant mosquitoes: a cluster, randomised controlled, two-by-two factorial design trial.

PubMed

Protopopoff, Natacha; Mosha, Jacklin F; Lukole, Eliud; Charlwood, Jacques D; Wright, Alexandra; Mwalimu, Charles D; Manjurano, Alphaxard; Mosha, Franklin W; Kisinza, William; Kleinschmidt, Immo; Rowland, Mark

2018-04-21

Progress in malaria control is under threat by wide-scale insecticide resistance in malaria vectors. Two recent vector control products have been developed: a long-lasting insecticidal net that incorporates a synergist piperonyl butoxide (PBO) and a long-lasting indoor residual spraying formulation of the insecticide pirimiphos-methyl. We evaluated the effectiveness of PBO long-lasting insecticidal nets versus standard long-lasting insecticidal nets as single interventions and in combination with the indoor residual spraying of pirimiphos-methyl. We did a four-group cluster randomised controlled trial using a two-by-two factorial design of 48 clusters derived from 40 villages in Muleba (Kagera, Tanzania). We randomly assigned these clusters using restricted randomisation to four groups: standard long-lasting insecticidal nets, PBO long-lasting insecticidal nets, standard long-lasting insecticidal nets plus indoor residual spraying, or PBO long-lasting insecticidal nets plus indoor residual spraying. Both standard and PBO nets were distributed in 2015. Indoor residual spraying was applied only once in 2015. We masked the inhabitants of each cluster to the type of nets received, as well as field staff who took blood samples. Neither the investigators nor the participants were masked to indoor residual spraying. The primary outcome was the prevalence of malaria infection in children aged 6 months to 14 years assessed by cross-sectional surveys at 4, 9, 16, and 21 months after intervention. The endpoint for assessment of indoor residual spraying was 9 months and PBO long-lasting insecticidal nets was 21 months. This trial is registered with ClinicalTrials.gov, number NCT02288637. 7184 (68·0%) of 10 560 households were selected for post-intervention survey, and 15 469 (89·0%) of 17 377 eligible children from the four surveys were included in the intention-to-treat analysis. Of the 878 households visited in the two indoor residual spraying groups, 827 (94%) had been sprayed. Reported use of long-lasting insecticidal nets, across all groups, was 15 341 (77·3%) of 19 852 residents after 1 year, decreasing to 12 503 (59·2%) of 21 105 in the second year. Malaria infection prevalence after 9 months was lower in the two groups that received PBO long-lasting insecticidal nets than in the two groups that received standard long-lasting insecticidal nets (531 [29%] of 1852 children vs 767 [42%] of 1809; odds ratio [OR] 0·37, 95% CI 0·21-0·65; p=0·0011). At the same timepoint, malaria prevalence in the two groups that received indoor residual spraying was lower than in groups that did not receive indoor residual spraying (508 [28%] of 1846 children vs 790 [44%] of 1815; OR 0·33, 95% CI 0·19-0·55; p<0·0001) and there was evidence of an interaction between PBO long-lasting insecticidal nets and indoor residual spraying (OR 2·43, 95% CI 1·19-4·97; p=0·0158), indicating redundancy when combined. The PBO long-lasting insecticidal net effect was sustained after 21 months with a lower malaria prevalence than the standard long-lasting insecticidal net (865 [45%] of 1930 children vs 1255 [62%] of 2034; OR 0·40, 0·20-0·81; p=0·0122). The PBO long-lasting insecticidal net and non-pyrethroid indoor residual spraying interventions showed improved control of malaria transmission compared with standard long-lasting insecticidal nets where pyrethroid resistance is prevalent and either intervention could be deployed to good effect. As a result, WHO has since recommended to increase coverage of PBO long-lasting insecticidal nets. Combining indoor residual spraying with pirimiphos-methyl and PBO long-lasting insecticidal nets provided no additional benefit compared with PBO long-lasting insecticidal nets alone or standard long-lasting insecticidal nets plus indoor residual spraying. UK Department for International Development, Medical Research Council, and Wellcome Trust. Copyright © 2018 The Author(s). Published by Elsevier Ltd. This is an Open Access article under the CC BY 4.0 license. Published by Elsevier Ltd.. All rights reserved.

To spray or not to spray? Understanding participation in an indoor residual spray campaign in Arequipa, Peru.

PubMed

Paz-Soldán, Valerie A; Bauer, Karin M; Hunter, Gabrielle C; Castillo-Neyra, Ricardo; Arriola, Vanessa D; Rivera-Lanas, Daniel; Rodriguez, Geoffrey H; Toledo Vizcarra, Amparo M; Mollesaca Riveros, Lina M; Levy, Michael Z; Buttenheim, Alison M

2018-01-01

Current low participation rates in vector control programmes in Arequipa, Peru complicate the control of Chagas disease. Using focus groups (n = 17 participants) and semi-structured interviews (n = 71) conducted in March and May 2013, respectively, we examined barriers to and motivators of household participation in an indoor residual spray (IRS) campaign that had taken place one year prior in Arequipa. The most common reported barriers to participation were inconvenient spray times due to work obligations, not considering the campaign to be necessary, concerns about secondary health impacts (e.g. allergic reactions to insecticides), and difficulties preparing the home for spraying (e.g. moving heavy furniture). There was also a low perception of risk for contracting Chagas disease that might affect participation. The main motivator to participate was to ensure personal health and well-being. Future IRS campaigns should incorporate more flexible hours, including weekends; provide appropriate educational messages to counter concerns about secondary health effects; incorporate peer educators to increase perceived risk to Chagas in community; obtain support from community members and leaders to build community trust and support for the campaign; and assist individuals in preparing their homes. Enhancing community trust in both the need for the campaign and its operations is key.

The US Air Force Aerial Spray Unit: a history of large area disease vector control operations, WWII through Katrina.

PubMed

Breidenbaugh, Mark; Haagsma, Karl

2008-01-01

The US Air Force has had a long history of aerial applications of pesticides to fulfill a variety of missions, the most important being the protection of troops through the minimization of arthropod vectors capable of disease transmission. Beginning in World War II, aerial application of pesticides by the military has effectively controlled vector and nuisance pest populations in a variety of environments. Currently, the military aerial spray capability resides in the US Air Force Reserve (USAFR), which operates and maintains C-130 airplanes capable of a variety of missions, including ultra low volume applications for vector and nuisance pests, as well as higher volume aerial applications of herbicides and oil-spill dispersants. The USAFR aerial spray assets are the only such fixed-wing aerial spray assets within the Department of Defense. In addition to troop protection, the USAFR Aerial Spray Unit has participated in a number of humanitarian/relief missions, most recently in the response to the 2005 Hurricanes Katrina and Rita, which heavily damaged the Gulf Coasts of Louisiana, Mississippi, and Texas. This article provides historical background on the Air Force Aerial Spray Unit and describes the operations in Louisiana in the aftermath of Hurricane Katrina.

Argon Shrouded Plasma Spraying of Tantalum over Titanium for Corrosion Protection in Fluorinated Nitric Acid Media

NASA Astrophysics Data System (ADS)

Vetrivendan, E.; Jayaraj, J.; Ningshen, S.; Mallika, C.; Kamachi Mudali, U.

2018-02-01

Argon shrouded plasma spraying (ASPS) was used to deposit a Ta coating on commercially pure Ti (CP-Ti) under inert argon, for dissolver vessel application in the aqueous spent fuels reprocessing plant with high plutonium content. Oxidation during plasma spraying was minimized by shrouding argon system. Porosity and oxide content were controlled by optimizing the spraying parameters, to obtain a uniform and dense Ta coating. The Ta particle temperature and velocity were optimized by judiciously controlling the spray parameters, using a spray diagnostic charge-coupled device camera. The corrosion resistance of the Ta coatings developed by ASPS was investigated by electrochemical studies in 11.5 M HNO3 and 11.5 M HNO3 + 0.05 M NaF. Similarly, the durability of the ASPS Ta coating/substrate was evaluated as per ASTM A262 Practice-C test in boiling nitric acid and fluorinated nitric acid for 240 h. The ASPS Ta coating exhibited higher corrosion resistance than the CP-Ti substrate, as evident from electrochemical studies, and low corrosion rate with excellent coating stability in boiling nitric, and fluorinated nitric acid. The results of the present study revealed that tantalum coating by ASPS is a promising strategy for improving the corrosion resistance in the highly corrosive reprocessing environment.

Coal-water slurry spray characteristics of an electronically-controlled accumulator fuel injection system

NASA Astrophysics Data System (ADS)

Caton, J. A.; Payne, S. E.; Terracina, D. P.; Kihm, K. D.

Experiments have been complete to characterize coal-water slurry sprays from a electronically-controlled accumulator fuel injection system of diesel engine. The sprays were injected into a pressurized chamber equipped with windows. High speed movies, fuel pressures and needle lifts were obtained as a function of time, orifice diameter, coal loading, gas density in the chamber, and accumulator fuel pressure. For the base conditions 50% (by mass) coal loading, 0.4 mm diameter nozzle hole, coal-water slurry pressure of 82 MPa (12,000 psi), and a chamber density of 25 kg/m(exp 3), the break-up time was 0.30 ms. An empirical correlation for both spray tip penetration and initial jet velocity was developed. For the conditions of this study, the spray tip penetration and initial jet velocity were 15% greater for coal-water slurry than for diesel fuel or water. Cone angles of the sprays were dependent on the operating conditions and fluid, as well as the time and locations of the measurement. The time-averaged cone angle for the base case conditions was 13.6 degrees. Results of this study and the correlation are specific to the tested coal-water slurry and are not general for other coal-water slurry fuels.

To spray or not to spray? Understanding participation in an indoor residual spray campaign in Arequipa, Peru

PubMed Central

Bauer, Karin M.; Hunter, Gabrielle C.; Castillo-Neyra, Ricardo; Arriola, Vanessa D.; Rivera-Lanas, Daniel; Rodriguez, Geoffrey H.; Toledo Vizcarra, Amparo M.; Mollesaca Riveros, Lina M.; Levy, Michael Z.; Buttenheim, Alison M.

2017-01-01

Current low participation rates in vector control programmes in Arequipa, Peru complicate the control of Chagas disease. Using focus groups (n = 17 participants) and semi-structured interviews (n = 71) conducted in March and May 2013, respectively, we examined barriers to and motivators of household participation in an indoor residual spray (IRS) campaign that had taken place one year prior in Arequipa. The most common reported barriers to participation were inconvenient spray times due to work obligations, not considering the campaign to be necessary, concerns about secondary health impacts (e.g. allergic reactions to insecticides), and difficulties preparing the home for spraying (e.g. moving heavy furniture). There was also a low perception of risk for contracting Chagas disease that might affect participation. The main motivator to participate was to ensure personal health and well-being. Future IRS campaigns should incorporate more flexible hours, including weekends; provide appropriate educational messages to counter concerns about secondary health effects; incorporate peer educators to increase perceived risk to Chagas in community; obtain support from community members and leaders to build community trust and support for the campaign; and assist individuals in preparing their homes. Enhancing community trust in both the need for the campaign and its operations is key. PMID:27189446

Warm spraying—a novel coating process based on high-velocity impact of solid particles

PubMed Central

Kuroda, Seiji; Kawakita, Jin; Watanabe, Makoto; Katanoda, Hiroshi

2008-01-01

In recent years, coating processes based on the impact of high-velocity solid particles such as cold spraying and aerosol deposition have been developed and attracting much industrial attention. A novel coating process called ‘warm spraying’ has been developed, in which coatings are formed by the high-velocity impact of solid powder particles heated to appropriate temperatures below the melting point of the powder material. The advantages of such process are as follows: (1) the critical velocity needed to form a coating can be significantly lowered by heating, (2) the degradation of feedstock powder such as oxidation can be significantly controlled compared with conventional thermal spraying where powder is molten, and (3) various coating structures can be realized from porous to dense ones by controlling the temperature and velocity of the particles. The principles and characteristics of this new process are discussed in light of other existing spray processes such as high-velocity oxy-fuel spraying and cold spraying. The gas dynamics of particle heating and acceleration by the spraying apparatus as well as the high-velocity impact phenomena of powder particles are discussed in detail. Several examples of depositing heat sensitive materials such as titanium, metallic glass, WC–Co cermet and polymers are described with potential industrial applications. PMID:27877996

Survival rates of Anopheles culicifacies s.l. and Anopheles pulcherrimus in sprayed and unsprayed villages in Ghassreghand district, Baluchistan, Iran, 1991.

PubMed

Zaim, M; Zahirnia, A H; Manouchehri, A V

1993-12-01

Survival rates, expectation of life, and expectation of infective life of Anopheles culicifacies and Anopheles pulcherrimus were estimated in sprayed and unsprayed villages in the highly malarious Ghassreghand District, Iran, during the 2 peak malaria transmission seasons in 1991. The daily survival rate of An. culicifacies was estimated as 0.84 and 0.78 during May and 0.89 and nil during September-October in the unsprayed and sprayed villages, respectively. For An. pulcherrimus the daily survival rate was estimated as 0.80 and 0.78 in May and 0.83 and 0.78 in September-October in the unsprayed and sprayed villages, respectively. The impact of indoor residual spraying during the first peak of transmission on An. culicifacies and An. pulcherrimus (expressed as the product of the degree of reduction of the expectation of infective life and the degree of reduction of expectation of life) was calculated as 3.5 and 1.5 times, respectively, that in the absence of control. The impact of indoor residual spraying on An. culicifacies during the second peak of transmission was almost complete, whereas that for An. pulcherrimus was 3.4 times than that in the absence of control.

Interaction of feel system and flight control system dynamics on lateral flying qualities

NASA Technical Reports Server (NTRS)

Bailey, Randall E.; Powers, Bruce G.; Shafer, Mary F.

1988-01-01

An investigation of feel system and flight control system dynamics on lateral flying qualities was conducted using the variable stability USAF NT-33 aircraft. Experimental variations in feel system natural frequency, force-deflection gradient, control system command architecture type, flight control system filter frequency, and control system delay were made. The experiment data include pilot ratings using the Cooper-Harper (1969) rating scale, pilot comments, and tracking performance statistic. Three test pilots served as evaluators. The data indicate that as the feel system natural frequency is reduced lateral flying qualities degrade. At the slowest feel system frequency, the closed-loop response becomes nonlinear with a 'bobweight' effect apparent in the feel system. Feel system influences were essentially independent of the control system architecture. The flying qualities influence due to the feel system was different than when the identical dynamic systenm was used as a flight control system element.

Early Testing in the Icing Research Tunnel

NASA Image and Video Library

1944-09-21

National Advisory Committee for Aeronautics (NACA) design engineers added the Icing Research Tunnel to the new Aircraft Engine Research Laboratory’s original layout to take advantage of the massive refrigeration system being constructed for the Altitude Wind Tunnel. The Icing Research Tunnel was built to study the formation of ice on aircraft surfaces and methods of preventing or eradicating that ice. Ice buildup adds extra weight, effects aerodynamics, and sometimes blocks airflow through engines. The Icing Research Tunnel is a closed-loop atmospheric wind tunnel with a 6- by 9-foot test section. The tunnel can produce speeds up to 300 miles per hour and temperatures from about 30 to –45⁰ F. Initially the tunnel used a spray bar system to introduce moisture into the airstream. NACA engineers struggled for nearly 10 years to perfect the spray system. The Icing Research Tunnel began testing in June of 1944. Initial testing, seen in this photograph, studied ice accumulation on propellers of a military aircraft. NACA reserach also produced a protected air scoop for the C–46 transport aircraft. A large number of C–46 aircraft were lost due to icing while flying supply runs over the Himalayas during World War II.

Discovering the flight autostabilizer of fruit flies by inducing aerial stumbles.

PubMed

Ristroph, Leif; Bergou, Attila J; Ristroph, Gunnar; Coumes, Katherine; Berman, Gordon J; Guckenheimer, John; Wang, Z Jane; Cohen, Itai

2010-03-16

Just as the Wright brothers implemented controls to achieve stable airplane flight, flying insects have evolved behavioral strategies that ensure recovery from flight disturbances. Pioneering studies performed on tethered and dissected insects demonstrate that the sensory, neurological, and musculoskeletal systems play important roles in flight control. Such studies, however, cannot produce an integrative model of insect flight stability because they do not incorporate the interaction of these systems with free-flight aerodynamics. We directly investigate control and stability through the application of torque impulses to freely flying fruit flies (Drosophila melanogaster) and measurement of their behavioral response. High-speed video and a new motion tracking method capture the aerial "stumble," and we discover that flies respond to gentle disturbances by accurately returning to their original orientation. These insects take advantage of a stabilizing aerodynamic influence and active torque generation to recover their heading to within 2 degrees in < 60 ms. To explain this recovery behavior, we form a feedback control model that includes the fly's ability to sense body rotations, process this information, and actuate the wing motions that generate corrective aerodynamic torque. Thus, like early man-made aircraft and modern fighter jets, the fruit fly employs an automatic stabilization scheme that reacts to short time-scale disturbances.

Biomonitoring of genotoxic risk in agricultural workers from five colombian regions: association to occupational exposure to glyphosate.

PubMed

Bolognesi, C; Carrasquilla, G; Volpi, S; Solomon, K R; Marshall, E J P

2009-01-01

In order to assess possible human effects associated with glyphosate formulations used in the Colombian aerial spray program for control of illicit crops, a cytogenetic biomonitoring study was carried out in subjects from five Colombian regions, characterized by different exposure to glyphosate and other pesticides. Women of reproductive age (137 persons 15-49 yr old) and their spouses (137 persons) were interviewed to obtain data on current health status, history, lifestyle, including past and current occupational exposure to pesticides, and factors including those known to be associated with increased frequency of micronuclei (MN). In regions where glyphosate was being sprayed, blood samples were taken prior to spraying (indicative of baseline exposure), 5 d after spraying, and 4 mo after spraying. Lymphocytes were cultured and a cytokinesis-block micronucleus cytome assay was applied to evaluate chromosomal damage and cytotoxicity. Compared with Santa Marta, where organic coffee is grown without pesticides, the baseline frequency of binucleated cells with micronuclei (BNMN) was significantly greater in subjects from the other four regions. The highest frequency of BNMN was in Boyaca, where no aerial eradication spraying of glyphosate was conducted, and in Valle del Cauca, where glyphosate was used for maturation of sugar cane. Region, gender, and older age (> or =35 yr) were the only variables associated with the frequency of BNMN measured before spraying. A significant increase in frequency of BNMN between first and second sampling was observed in Narino, Putumayo, and Valle immediately (<5 d) after spraying. In the post-spray sample, those who reported direct contact with the eradication spray showed a higher quantitative frequency of BNMN compared to those without glyphosate exposure. The increase in frequency of BNMN observed immediately after the glyphosate spraying was not consistent with the rates of application used in the regions and there was no association between self-reported direct contact with eradication sprays and frequency of BNMN. Four months after spraying, a statistically significant decrease in the mean frequency of BNMN compared with the second sampling was observed in Narino, but not in Putumayo and Valle del Cauca. Overall, data suggest that genotoxic damage associated with glyphosate spraying for control of illicit crops as evidenced by MN test is small and appears to be transient. Evidence indicates that the genotoxic risk potentially associated with exposure to glyphosate in the areas where the herbicide is applied for coca and poppy eradication is low.

On the prediction of spray angle of liquid-liquid pintle injectors

NASA Astrophysics Data System (ADS)

Cheng, Peng; Li, Qinglian; Xu, Shun; Kang, Zhongtao

2017-09-01

The pintle injector is famous for its capability of deep throttling and low cost. However, the pintle injector has been seldom investigated. To get a good prediction of the spray angle of liquid-liquid pintle injectors, theoretical analysis, numerical simulations and experiments were conducted. Under the hypothesis of incompressible and inviscid flow, a spray angle formula was deduced from the continuity and momentum equations based on a control volume analysis. The formula was then validated by numerical and experimental data. The results indicates that both geometric and injection parameters affect the total momentum ratio (TMR) and then influence the spray angle formed by liquid-liquid pintle injectors. TMR is the pivotal non-dimensional number that dominates the spray angle. Compared with gas-gas pintle injectors, spray angle formed by liquid-liquid injectors is larger, which benefits from the local high pressure zone near the pintle wall caused by the impingement of radial and axial sheets.

Preliminary Design of Aerial Spraying System for Microlight Aircraft

NASA Astrophysics Data System (ADS)

Omar, Zamri; Idris, Nurfazliawati; Rahim, M. Zulafif

2017-10-01

Undoubtedly agricultural is an important sector because it provides essential nutrients for human, and consequently is among the biggest sector for economic growth worldwide. It is crucial to ensure crops production is protected from any plant diseases and pests. Thus aerial spraying system on crops is developed to facilitate farmers to for crops pests control and it is very effective spraying method especially for large and hilly crop areas. However, the use of large aircraft for aerial spaying has a relatively high operational cost. Therefore, microlight aircraft is proposed to be used for crops aerial spraying works for several good reasons. In this paper, a preliminary design of aerial spraying system for microlight aircraft is proposed. Engineering design methodology is adopted in the development of the aerial sprayer and steps involved design are discussed thoroughly. A preliminary design for the microlight to be attached with an aerial spraying system is proposed.

Experimental testing of spray dryer for control of incineration emissions.

PubMed

Wey, M Y; Wu, H Y; Tseng, H H; Chen, J C

2003-05-01

The research investigated the absorption/adsorption efficiency of sulfur dioxide (SO2), heavy metals, and polycyclic aromatic hydrocarbons (PAHs) with different Ca-based sorbents in a spray dryer during incineration process. For further improving the adsorption capacity of Ca-based sorbents, different spraying pressure and additives were carried out in this study. Experimental results showed that CaO could be used as an alternative sorbent in the spray dryer at an optimal initial particle size distribution of spraying droplet. In the spray dryer, Ca-based sorbents provided a lot of sites for heavy metals and PAHs condensing and calcium and alkalinity to react with metals to form merged species. As a result, heavy metals and PAHs could be removed from the flue gas simultaneously by condensation and adsorption. The additions of additives NaHCO3, SiO2, and KMnO4 were also found to be effective in improving the removal efficiency of these air pollutants.

A critical assessment of in-flight particle state during plasma spraying of YSZ and its implications on coating properties and process reliability

NASA Astrophysics Data System (ADS)

Srinivasan, Vasudevan

Air plasma spray is inherently complex due to the deviation from equilibrium conditions, three dimensional nature, multitude of interrelated (controllable) parameters and (uncontrollable) variables involved, and stochastic variability at different stages. The resultant coatings are complex due to the layered high defect density microstructure. Despite the widespread use and commercial success for decades in earthmoving, automotive, aerospace and power generation industries, plasma spray has not been completely understood and prime reliance for critical applications such as thermal barrier coatings on gas turbines are yet to be accomplished. This dissertation is aimed at understanding the in-flight particle state of the plasma spray process towards designing coatings and achieving coating reliability with the aid of noncontact in-flight particle and spray stream sensors. Key issues such as the phenomena of optimum particle injection and the definition of spray stream using particle state are investigated. Few strategies to modify the microstructure and properties of Yttria Stabilized Zirconia coatings are examined systematically using the framework of process maps. An approach to design process window based on design relevant coating properties is presented. Options to control the process for enhanced reproducibility and reliability are examined and the resultant variability is evaluated systematically at the different stages in the process. The 3D variability due to the difference in plasma characteristics has been critically examined by investigating splats collected from the entire spray footprint.

Synchronized droplet size measurements for Coal-Water-Slurry (CWS) diesel sprays of an electronically-controlled fuel injection system

NASA Astrophysics Data System (ADS)

Kihm, K. D.; Terracina, D. P.; Payne, S. E.; Caton, J. A.

Experiments were completed to study intermittent coal-water slurry (CWS) fuel sprays injected from an electronically-controlled accumulator injector system. A laser diffraction particle analyzing (LDPA) technique was used to measure the spray diameters (Sauter mean diameter, SMD) assuming the Rosin-Rammler two parameter model. In order to ensure an accurate synchronization of the measurement with the intermittent sprays, a new synchronization technique was developed using the light extinction signal as a triggering source for the data taking initiation. This technique allowed measurement of SMD's near the spray tip where the light extinction was low and the data were free from the multiscattering bias. Coal-water slurry fuel with 50% coal loading in mass containing 5 (mu)m mass median diameter coal particulates was considered. Injection pressures ranging from 28 to 110 MPa, two different nozzle orifice diameters, 0.2 ad 0.4 mm, and four axial measurement locations from 60 to 120 mm from the nozzle orifice were studied. Measurements were made for pressurized (2.0 MPa in gauge) and for ambient chamber conditions. The spray SMD showed an increase with the distance of the axial measurement location and with the ambient gas density, and showed a decrease with increasing injection pressure. A correlation of the Sauter mean diameter with the injection conditions was determined. The results were also compared with previous SMD correlations that were available only for diesel fuel sprays.

Water injected fuel cell system compressor

DOEpatents

Siepierski, James S.; Moore, Barbara S.; Hoch, Martin Monroe

2001-01-01

A fuel cell system including a dry compressor for pressurizing air supplied to the cathode side of the fuel cell. An injector sprays a controlled amount of water on to the compressor's rotor(s) to improve the energy efficiency of the compressor. The amount of water sprayed out the rotor(s) is controlled relative to the mass flow rate of air inputted to the compressor.

Releases of Psyttalia fletcheri (Hymenoptera: Braconidae) and sterile flies to suppress melon fly (Diptera: Tephritidae) in Hawaii.

PubMed

Vargas, Roger I; Long, Jay; Miller, Neil W; Delate, Kathleen; Jackson, Charles G; Uchida, Grant K; Bautista, Renato C; Harris, Ernie J

2004-10-01

Ivy gourd, Coccinia grandis (L.) Voigt, patches throughout Kailua-Kona, Hawaii Island, HI, were identified as persistent sources of melon fly, Bactrocera cucurbitae (Coquillett). These patches had a low incidence of Psyttalia fletcheri (Silvestri), its major braconid parasitoid natural enemy in Hawaii, and were used to evaluate augmentative releases of P. fletcheri against melon fly. In field cage studies of releases, numbers of melon flies emerging from ivy gourd fruit placed inside treatment cages were reduced up to 21-fold, and numbers of parasitoids were increased 11-fold. In open field releases of P. fletcheri into ivy gourd patches, parasitization rates were increased 4.7 times in release plots compared with those in control plots. However, there was no significant reduction in emergence of melon flies from fruit. In subsequent cage tests with sterile melon flies and P. fletcheri, combinations of sterile flies and P. fletcheri produced the greatest reduction (9-fold) in melon fly emergence from zucchini, Cucurbita pepo L. Reductions obtained with sterile flies alone or in combination with parasitoids were significantly greater than those in the control, whereas those for parasitoids alone were not. Although these results suggest that the effects of sterile flies were greater than those for parasitoids, from a multitactic melon fly management strategy, sterile flies would complement the effects of P. fletcheri. Cost and sustainability of these nonchemical approaches will be examined further in an ongoing areawide pest management program for melon fly in Hawaii.

Famous landmark identification in amnestic mild cognitive impairment and Alzheimer's disease.

PubMed

Sheardova, Katerina; Laczó, Jan; Vyhnalek, Martin; Andel, Ross; Mokrisova, Ivana; Vlcek, Kamil; Amlerova, Jana; Hort, Jakub

2014-01-01

Identification of famous landmarks (FLI), famous faces (FFI) and recognition of facial emotions (FER) is affected early in the course of Alzheimer's disease (AD). FFI, FER and FLI may represent domain specific tasks relying on activation of distinct regions of the medial temporal lobe, which are affected successively during the course of AD. However, the data on FFI and FER in MCI are controversial and FLI domain remains almost unexplored. To determine whether and how are these three specific domains impaired in head to head comparison of patients with amnestic MCI (aMCI) single domain (SD-aMCI) and multiple domain (MD-aMCI). We propose that FLI might be most reliable in differentiating SD-aMCI, which is considered to be an earlier stage of AD pathology spread out, from the controls. A total of 114 patients, 13 with single domain (SD-aMCI) and 30 with multiple domains (MD-aMCI), 29 with mild AD and 42 controls underwent standard neurological and neuropsychological evaluations as well as tests of FLI, FER and FFI. Compared to the control group, AD subjects performed worse on FFI (p = 0.020), FER (p<0.001) and FLI (p<0.001), MD-aMCI group had significantly worse scores only on FLI (p = 0.002) and approached statistical significance on FER (0.053). SD-aMCI group performed significantly worse only on FLI (p = 0.028) compared to controls. Patients with SD-aMCI had an isolated impairment restricted to FLI, while patients with MD-aMCI showed impairment in FLI as well as in FER. Patients with mild dementia due to AD have more extensive impairment of higher visual perception. The results suggest that FLI testing may contribute to identification of patients at risk of AD. We hypothesize that clinical examination of all three domains might reflect the spread of the disease from transentorhinal cortex, over amygdala to fusiform gyrus.

Famous Landmark Identification in Amnestic Mild Cognitive Impairment and Alzheimer's Disease

PubMed Central

Sheardova, Katerina; Laczó, Jan; Vyhnalek, Martin; Andel, Ross; Mokrisova, Ivana; Vlcek, Kamil; Amlerova, Jana; Hort, Jakub

2014-01-01

Background Identification of famous landmarks (FLI), famous faces (FFI) and recognition of facial emotions (FER) is affected early in the course of Alzheimer's disease (AD). FFI, FER and FLI may represent domain specific tasks relying on activation of distinct regions of the medial temporal lobe, which are affected successively during the course of AD. However, the data on FFI and FER in MCI are controversial and FLI domain remains almost unexplored. Objectives To determine whether and how are these three specific domains impaired in head to head comparison of patients with amnestic MCI (aMCI) single domain (SD-aMCI) and multiple domain (MD-aMCI). We propose that FLI might be most reliable in differentiating SD-aMCI, which is considered to be an earlier stage of AD pathology spread out, from the controls. Patients and Methods A total of 114 patients, 13 with single domain (SD–aMCI) and 30 with multiple domains (MD–aMCI), 29 with mild AD and 42 controls underwent standard neurological and neuropsychological evaluations as well as tests of FLI, FER and FFI. Results Compared to the control group, AD subjects performed worse on FFI (p = 0.020), FER (p<0.001) and FLI (p<0.001), MD-aMCI group had significantly worse scores only on FLI (p = 0.002) and approached statistical significance on FER (0.053). SD-aMCI group performed significantly worse only on FLI (p = 0.028) compared to controls. Conclusions Patients with SD-aMCI had an isolated impairment restricted to FLI, while patients with MD–aMCI showed impairment in FLI as well as in FER. Patients with mild dementia due to AD have more extensive impairment of higher visual perception. The results suggest that FLI testing may contribute to identification of patients at risk of AD. We hypothesize that clinical examination of all three domains might reflect the spread of the disease from transentorhinal cortex, over amygdala to fusiform gyrus. PMID:25144755

Growth and physiological response of lemongrass (Cymbopogon citratus (D.C.) Stapf.) under different levels of fly ash-amended soil.

PubMed

Panda, Debabrata; Panda, Dibyajyoti; Padhan, Bandana; Biswas, Meghali

2018-05-12

Revegetation with metal tolerant plants for management of fly ash deposits is an important environmental perspective nowadays. Growth performance, photosynthesis, and antioxidant defense of lemongrass (Cymbopogon citratus (D.C.) Stapf.) were evaluated under various combination of fly ash amended with garden soil in order to assess its fly ash tolerance potential. Under low level of fly ash (25%) amended soil, the plant growth parameters such as shoot, root, and total plant biomass as well as metal tolerance index were increased compared to the control plants grown on garden soil, followed by decline under higher concentration of fly ash (50%, 75% and 100%). In addition, leaf photosynthetic rate, stomatal conductance, and photosystem (PS) II activity were not significantly changed under low level of fly ash (25%) amended soil compared to the garden soil but these parameters were significantly decreased further with increase of fly ash concentrations. Furthermore, increase of activities of some antioxidant enzymes such as superoxide dismutase, ascorbate peroxidase, and guaiacol peroxidase over control were noticed in lemongrass under all fly ash treatments. Taken together, the study suggests that lemongrass can be used for phytoremediation of fly ash at 25% amended soil.

Laboratory evaluation for a potential birth control diet for fruit fly sterilization insect technique (SIT)

USDA-ARS?s Scientific Manuscript database

A potential fruit fly steilizing diet was evaluated on fertility, mating, survival, and protein anaylsis for fruit fly species in Hawaii. Insects were continuously fed an agar diet with lufenuron(LFN) for an initial 7d after emergence and then switched to a control diet to simulate the actual field ...

Genome-based approach to discover new livestock pest control technologies: The horn fly (Haematobia irritans) genome sequencing project

USDA-ARS?s Scientific Manuscript database

Invasion of the Americas by the horn fly, H. irritans, has resulted in control issues throughout the continent. Insecticide resistance is a major complicating factor with efforts to manage this pest. Stakeholder focus groups identified the horn fly as the top priority arthropod pest affecting cattle...

Mosquito and Fly Surveillance and Control Research at the USDA-ARS Center for Medical, Agricultural and Veterinary Entomology: Solving Operational Challenges

USDA-ARS?s Scientific Manuscript database

The Mosquito and Fly Research Unit of the USDA-ARS Center for Medical, Agricultural and Veterinary Entomology located in Gainesville Florida is the largest Federal laboratory devoted to specifically solving operational mosquito and fly surveillance and control challenges in the U.S. and internationa...

Evaluation of spray application methods for navel orangeworm control in almonds.

PubMed

Markle, James C; Niederholzer, Franz Ja; Zalom, Frank G

2016-12-01

Gear Up/Throttle Down (GUTD) and Inward Only strategies represent potential alternatives to conventional airblast applications to reduce spray drift. This study evaluates Inward Only and a modified version of GUTD in almonds, the largest US tree crop, at the recommended hull split treatment timing for control of navel orangeworm (NOW), the key almond insect pest. Conventional treatment produced the most drift (15.6% of total bifenthrin load), while the GUTD and Inward Only treatments produced only 7.6 and 9.7% respectively. For all methods, 92-94% of the drift was found in the first 15.2 m downwind of the orchard. NOW control was lower for the Inward Only treatment compared with the GUTD and conventional treatments. NOW control was consistently lower at 4.88 m height relative to 2.44 m in all treatments, reflecting the reduced deposition higher in the tree canopy recorded in deposition samples. While Inward Only treatments reduced spray drift relative to the conventional application method, poorer control of NOW, the key insect pest of almonds, in the Inward Only treatment would likely limit its voluntary use by growers. However, GUTD holds promise for use at the hull split treatment timing to address spray drift. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Triatomine Infestation in Guatemala: Spatial Assessment after Two Rounds of Vector Control

PubMed Central

Manne, Jennifer; Nakagawa, Jun; Yamagata, Yoichi; Goehler, Alexander; Brownstein, John S.; Castro, Marcia C.

2012-01-01

In 2000, the Guatemalan Ministry of Health initiated a Chagas disease program to control Rhodnius prolixus and Triatoma dimidiata by periodic house spraying with pyrethroid insecticides to characterize infestation patterns and analyze the contribution of programmatic practices to these patterns. Spatial infestation patterns at three time points were identified using the Getis-Ord Gi*(d) test. Logistic regression was used to assess predictors of reinfestation after pyrethroid insecticide administration. Spatial analysis showed high and low clusters of infestation at three time points. After two rounds of spray, 178 communities persistently fell in high infestation clusters. A time lapse between rounds of vector control greater than 6 months was associated with 1.54 (95% confidence interval = 1.07–2.23) times increased odds of reinfestation after first spray, whereas a time lapse of greater than 1 year was associated with 2.66 (95% confidence interval = 1.85–3.83) times increased odds of reinfestation after first spray compared with localities where the time lapse was less than 180 days. The time lapse between rounds of vector control should remain under 1 year. Spatial analysis can guide targeted vector control efforts by enabling tracking of reinfestation hotspots and improved targeting of resources. PMID:22403315

Adaptive-Repetitive Visual-Servo Control of Low-Flying Aerial Robots via Uncalibrated High-Flying Cameras

NASA Astrophysics Data System (ADS)

Guo, Dejun; Bourne, Joseph R.; Wang, Hesheng; Yim, Woosoon; Leang, Kam K.

2017-08-01

This paper presents the design and implementation of an adaptive-repetitive visual-servo control system for a moving high-flying vehicle (HFV) with an uncalibrated camera to monitor, track, and precisely control the movements of a low-flying vehicle (LFV) or mobile ground robot. Applications of this control strategy include the use of high-flying unmanned aerial vehicles (UAVs) with computer vision for monitoring, controlling, and coordinating the movements of lower altitude agents in areas, for example, where GPS signals may be unreliable or nonexistent. When deployed, a remote operator of the HFV defines the desired trajectory for the LFV in the HFV's camera frame. Due to the circular motion of the HFV, the resulting motion trajectory of the LFV in the image frame can be periodic in time, thus an adaptive-repetitive control system is exploited for regulation and/or trajectory tracking. The adaptive control law is able to handle uncertainties in the camera's intrinsic and extrinsic parameters. The design and stability analysis of the closed-loop control system is presented, where Lyapunov stability is shown. Simulation and experimental results are presented to demonstrate the effectiveness of the method for controlling the movement of a low-flying quadcopter, demonstrating the capabilities of the visual-servo control system for localization (i.e.,, motion capturing) and trajectory tracking control. In fact, results show that the LFV can be commanded to hover in place as well as track a user-defined flower-shaped closed trajectory, while the HFV and camera system circulates above with constant angular velocity. On average, the proposed adaptive-repetitive visual-servo control system reduces the average RMS tracking error by over 77% in the image plane and over 71% in the world frame compared to using just the adaptive visual-servo control law.

Optimal Path Determination for Flying Vehicle to Search an Object

NASA Astrophysics Data System (ADS)

Heru Tjahjana, R.; Heri Soelistyo U, R.; Ratnasari, L.; Irawanto, B.

2018-01-01

In this paper, a method to determine optimal path for flying vehicle to search an object is proposed. Background of the paper is controlling air vehicle to search an object. Optimal path determination is one of the most popular problem in optimization. This paper describe model of control design for a flying vehicle to search an object, and focus on the optimal path that used to search an object. In this paper, optimal control model is used to control flying vehicle to make the vehicle move in optimal path. If the vehicle move in optimal path, then the path to reach the searched object also optimal. The cost Functional is one of the most important things in optimal control design, in this paper the cost functional make the air vehicle can move as soon as possible to reach the object. The axis reference of flying vehicle uses N-E-D (North-East-Down) coordinate system. The result of this paper are the theorems which say that the cost functional make the control optimal and make the vehicle move in optimal path are proved analytically. The other result of this paper also shows the cost functional which used is convex. The convexity of the cost functional is use for guarantee the existence of optimal control. This paper also expose some simulations to show an optimal path for flying vehicle to search an object. The optimization method which used to find the optimal control and optimal path vehicle in this paper is Pontryagin Minimum Principle.

Vestergaard zerofly fabric for fly control in the US

USDA-ARS?s Scientific Manuscript database

Vestergaard ZeroFly pesticide-impregnated fabric has been evaluated in zero-graze swine and cattle farms in Sub-Saharan Africa for management of biting flies, particularly those capable of transmitting Nangana, i.e. tsetse. Other major blood-feeding flies encountered around these units are various s...

Mixing of an Airblast-atomized Fuel Spray Injected into a Crossflow of Air

NASA Technical Reports Server (NTRS)

Leong, May Y.; McDonell, Vincent G.; Samuelsen, G. Scott

2000-01-01

The injection of a spray of fuel droplets into a crossflow of air provides a means of rapidly mixing liquid fuel and air for combustion applications. Injecting the liquid as a spray reduces the mixing length needed to accommodate liquid breakup, while the transverse injection of the spray into the air stream takes advantage of the dynamic mixing induced by the jet-crossflow interaction. The structure of the spray, formed from a model plain-jet airblast atomizer, is investigated in order to determine and understand the factors leading to its dispersion. To attain this goal, the problem is divided into the following tasks which involve: (1) developing planar imaging techniques that visualize fuel and air distributions in the spray, (2) characterizing the airblast spray without a crossflow, and (3) characterizing the airblast spray upon injection into a crossflow. Geometric and operating conditions are varied in order to affect the atomization, penetration, and dispersion of the spray into the crossflow. The airblast spray is first characterized, using imaging techniques, as it issues into a quiescent environment. The spray breakup modes are classified in a liquid Reynolds number versus airblast Weber number regime chart. This work focuses on sprays formed by the "prompt" atomization mode, which induces a well-atomized and well-dispersed spray, and which also produces a two-lobed liquid distribution corresponding to the atomizing air passageways in the injector. The characterization of the spray jet injected into the crossflow reveals the different processes that control its dispersion. Correlations that describe the inner and outer boundaries of the spray jet are developed, using the definition of a two-phase momentum-flux ratio. Cross-sections of the liquid spray depict elliptically-shaped distributions, with the exception of the finely-atomized sprays which show kidney-shaped distributions reminiscent of those obtained in gaseous jet in crossflow systems. A droplet trajectory analysis overpredicts the liquid mass penetration, and indicates a need for a more rigorous model to account for the three-dimensional mixing field induced by the jet-crossflow interaction. Nonetheless, the general procedures and criteria that are outlined can be used to efficiently assess and compare the quality of sprays formed under different conditions.

Spark Ignition of Monodisperse Fuel Sprays. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Danis, Allen M.; Cernansky, Nicholas P.; Namer, Izak

1987-01-01

A study of spark ignition energy requirements was conducted with a monodisperse spray system allowing independent control of droplet size, equivalent ratio, and fuel type. Minimum ignition energies were measured for n-heptane and methanol sprays characterized at the spark gap in terms of droplet diameter, equivalence ratio (number density) and extent of prevaporization. In addition to sprays, minimum ignition energies were measured for completely prevaporized mixtures of the same fuels over a range of equivalence ratios to provide data at the lower limit of droplet size. Results showed that spray ignition was enhanced with decreasing droplet size and increasing equivalence ratio over the ranges of the parameters studied. By comparing spray and prevaporized ignition results, the existence of an optimum droplet size for ignition was indicated for both fuels. Fuel volatility was seen to be a critical factor in spray ignition. The spray ignition results were analyzed using two different empirical ignition models for quiescent mixtures. Both models accurately predicted the experimental ignition energies for the majority of the spray conditions. Spray ignition was observed to be probabilistic in nature, and ignition was quantified in terms of an ignition frequency for a given spark energy. A model was developed to predict ignition frequencies based on the variation in spark energy and equivalence ratio in the spark gap. The resulting ignition frequency simulations were nearly identical to the experimentally observed values.

Sustained release of diltiazem HCl tableted after co-spray drying and physical mixing with PVAc and PVP.

PubMed

Al-Zoubi, Nizar; Al-Obaidi, Ghada; Tashtoush, Bassam; Malamataris, Stavros

2016-01-01

In this work, aqueous diltiazem HCl and polyvinyl-pyrrolidone (PVP) solutions were mixed with Kollicoat SR 30D and spray dried to microparticles of different drug:excipient ratio and PVP content. Co-spray dried products and physical mixtures of drug, Kollidon SR and PVP were tableted. Spray drying process, co-spray dried products and compressibility/compactability of co-spray dried and physical mixtures, as well as drug release and water uptake of matrix-tablets was evaluated. Simple power equation fitted drug release and water uptake (R(2) > 0.909 and 0.938, respectively) and correlations between them were examined. Co-spray dried products with PVP content lower than in physical mixtures result in slower release, while at equal PVP content (19 and 29% w/w of excipient) in similar release (f2 > 50). Increase of PVP content increases release rate and co-spray drying might be an alternative, when physical mixing is inadequate. Co-spray dried products show better compressibility/compatibility but higher stickiness to the die-wall compared to physical mixtures. SEM observations and comparison of release and swelling showed that distribution of tableted component affects only the swelling, while PVP content for both co-spray dried and physical mixes is major reason for release alterations and an aid for drug release control.

A double-blind, randomized, placebo-controlled, parallel group study of THC/CBD spray in peripheral neuropathic pain treatment.

PubMed

Serpell, M; Ratcliffe, S; Hovorka, J; Schofield, M; Taylor, L; Lauder, H; Ehler, E

2014-08-01

Peripheral neuropathic pain (PNP) associated with allodynia poses a significant clinical challenge. The efficacy of Δ(9) -tetrahydrocannabinol/cannabidiol (THC/CBD) oromucosal spray, a novel cannabinoid formulation, was investigated in this 15-week randomized, double-blind, placebo-controlled parallel group study. In total, 303 patients with PNP associated with allodynia were screened; 128 were randomized to THC/CBD spray and 118 to placebo, in addition to their current analgesic therapy. The co-primary efficacy endpoints were the 30% responder rate in PNP 0-10 numerical rating scale (NRS) score and the mean change from baseline to the end of treatment in this score. Various key secondary measures of pain and functioning were also investigated. At the 30% responder level, there were statistically significant treatment differences in favour of THC/CBD spray in the full analysis (intention-to-treat) dataset [p = 0.034; 95% confidence interval (CI): 1.05-3.70]. There was also a reduction in mean PNP 0-10 NRS scores in both treatment groups that was numerically higher in the THC/CBD spray group, but which failed to reach statistical significance. Secondary measures of sleep quality 0-10 NRS score (p = 0.0072) and Subject Global Impression of Change (SGIC) (p = 0.023) also demonstrated statistically significant treatment differences in favour of THC/CBD spray treatment. These findings demonstrate that, in a meaningful proportion of otherwise treatment-resistant patients, clinically important improvements in pain, sleep quality and SGIC of the severity of their condition are obtained with THC/CBD spray. THC/CBD spray was well tolerated and no new safety concerns were identified. © 2014 European Pain Federation - EFIC®

The Effects of Fuel and Cylinder Gas Densities on the Characteristics of Fuel Sprays for Oil Engines

NASA Technical Reports Server (NTRS)

Joachim, W F; Beardsley, Edward G

1928-01-01

This investigation was conducted as a part of a general research on fuel-injection engines for aircraft. The purpose of the investigation was to determine the effects of fuel and cylinder gas densities with several characteristics of fuel sprays for oil engines. The start, growth, and cut-off of single fuel sprays produced by automatic injection valves were recorded on photographic film by means of special high-speed motion-picture apparatus. This equipment, which has been described in previous reports, is capable of taking twenty-five consecutive pictures of the moving spray at the rate of 4,000 per second. The penetrations of the fuel sprays increased and the cone angles and relative distributions decreased with increase in the specific gravity of the fuel. The density of the gas into which the fuel sprays were injected controlled their penetration. This was the only characteristic of the chamber gas that had a measurable effect upon the fuel sprays. Application of fuel-spray penetration data to the case of an engine, in which the pressure is rising during injection, indicated that fuel sprays may penetrate considerably farther than when injected into a gas at a density equal to that of the gas in an engine cylinder at top center.

Aerodynamic Characteristics of a Flying-Boat Hull Having a Length-Beam Ratio of 15, TED No. NACA 2206

NASA Technical Reports Server (NTRS)

Riebe, John M.; Naeseth, Rodger L.

1951-01-01

An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of a flying-boat hull of a length-beam ratio of 15 in the presence of a wing. The investigation was an extension of previous tests made on hulls of length-beam ratios of 6, 9, and 12; these hulls were designed to have approximately the same hydrodynamic performance with respect to spray and resistance characteristics. Comparison with the previous investigation at lower length-beam ratios indicated a reduction in minimum drag coefficients of 0.0006 (10 peroent)with fixed transition when the length-beam ratio was extended from 12 to 15. As with the hulls of lower length-beam ratio, the drag reduction with a length-beam ratio of 15 occurred throughout the range of angle of attack tested and the angle of attack for minimum drag was in the range from 2deg to 3deg. Increasing the length-beam ratio from 12 to 15 reduced the hull longitudinal instability by an mount corresponding to an aerodynamic-center shift of about 1/2 percent of the mean aerodynamic chord of the hypothetical flying boat. At an angle of attack of 2deg, the value of the variation of yawing-moment coefficient with angle of yaw for a length-beam ratio of 15 was 0.00144, which was 0.00007 larger than the value for a length-beam ratio of 12.

Comparison of JP-8 Sprays from a Hydraulically Actuated Electronically Controlled Unit Injector and a Common Rail Injector

DTIC Science & Technology

2015-10-01

acquired of a calibration plate to provide scaling for the injector orifices. The determined scaling factor for the images was 0.3 µm/pixel. A circle...Controlled Unit Injector and a Common Rail Injector by Matthew Kurman, Michael Tess, Luis Bravo, Chol-Bum Kweon, and Craig Hershey Reprinted...Comparison of JP-8 Sprays from a Hydraulically Actuated Electronically Controlled Unit Injector and a Common Rail Injector by Matthew Kurman

Genes expressed differentially in Hessian fly larvae feeding in resistant and susceptible plants

USDA-ARS?s Scientific Manuscript database

The Hessian fly, Mayetiola destructor, is a destructive pest of wheat worldwide and mainly controlled by deploying resistant cultivars. Hessian fly larvae manipulate susceptible plants extensively, but are unable to manipulate resistant plants and thus die in them. The mechanisms for Hessian fly l...

Effects of Pyriproxyfen and Buprofezin on Immature Development and Reproduction in the Stable Fly

USDA-ARS?s Scientific Manuscript database

The stable fly, Stomoxys calcitrans (L.) (Diptera: Muscidae) is one of the most significant biting flies affecting cattle. Use of traditional insecticides for stable fly control has only limited success due to the insect’s unique feeding behaviors and immature development sites. A laboratory study...

In Vitro Assessment of Spray Deposition Patterns in a Pediatric (12 Year-Old) Nasal Cavity Model.

PubMed

Sawant, Namita; Donovan, Maureen D

2018-03-26

Nasal sprays available for the treatment of cold and allergy symptoms currently use identical formulations and devices for adults as well as for children. Due to the obvious differences between the nasal airway dimensions of a child and those of an adult, the performance of nasal sprays in children was evaluated. Deposition patterns of nasal sprays administered to children were tested using a nasal cast based on MRI images obtained from a 12 year old child's nasal cavity. Test formulations emitting a range of spray patterns were investigated by actuating the device into the pediatric nasal cast under controlled conditions. The results showed that the nasal sprays impacted in the anterior region of the 12 year old child's nasal cavity, and only limited spray entered the turbinate region - the effect site for most topical drugs and the primary absorptive region for systemically absorbed drugs. Differences in deposition patterns following the administration of nasal sprays to adults and children may lead to differences in efficacy between these populations. Greater anterior deposition in children may result in decreased effectiveness, greater anterior dosage form loss, and the increased potential for patient non-compliance.

Spray-coated carbon nanotube thin-film transistors with striped transport channels

NASA Astrophysics Data System (ADS)

Jeong, Minho; Lee, Kunhak; Choi, Eunsuk; Kim, Ahsung; Lee, Seung-Beck

2012-12-01

We present results for the transfer characteristics of carbon nanotube thin-film transistors (CNT-TFTs) that utilize single-walled carbon nanotube thin-films prepared by direct spray-coating on the substrate. By varying the number of spray-coatings (Nsp) and the concentration of nanotubes in solution (CNT), it was possible to control the conductivity of the spray-coated nanotube thin-film from 129 to 0.1 kΩ/□. Also, by introducing stripes into the channel of the CNT-TFT, and thereby reducing the number of metallic percolation paths between source and drain, it was possible to enhance the on/off current ratio 1000-fold, from 10 to 104, demonstrating that it may be possible to utilize spray-coating as a method to fabricate CNT-TFTs for large area switching array applications.

Financial analysis of East Coast fever control strategies in traditionally managed Sanga cattle in Central Province of Zambia.

PubMed

Minjauw, B; Rushton, J; James, A D; Upton, M

1999-01-01

Five different East Coast fever (ECF)-control strategies (involving ECF immunisation by the infection-and-treatment method) were tested in groups of traditionally managed Sanga cattle in the Central Province of Zambia over a period of 2.5 years. Two groups were under intensive tick control (weekly spraying with acaricide)--one group immunised and the other non-immunised. Two groups were under no tick control--one group immunised and the other non-immunised. The fifth group was under seasonal tick control (18 sprays/year) and was immunised against ECF. The input and output data were used to construct discounted cash flows for each group. The seasonally sprayed and immunised group gave the highest net present value, and the non-immunised group with no tick control, the lowest. A break-even analysis showed that the immunisation costs could rise to US$25.9 per animal before profitability was affected. For herds under intensive tick control, immunisation was of no financial benefit. The results demonstrate the value of immunisation, and indicate the importance of its combination with seasonal tick-control measures.

Heat- and humidity-induced plastic changes in body lipids and starvation resistance in the tropical fly Zaprionus indianus during wet and dry seasons.

PubMed

Girish, T N; Pradeep, B E; Parkash, Ravi

2018-05-04

Insects in tropical wet or dry seasons are likely to cope with starvation stress through plastic changes (developmental as well as adult acclimation) in energy metabolites. Control and experimental groups of Zaprionus indianus flies were reared under wet or dry conditions, but adults were acclimated at different thermal or humidity conditions. Adult flies of the control group were acclimated at 27°C and low (50%) or high (60%) relative humidity (RH). For experimental groups, adult flies were acclimated at 32°C for 1 to 6 days and under low (40%) or high (70%) RH. For humidity acclimation, adult flies were acclimated at 27°C but under low (40%) or high (70%) RH for 1 to 6 days. Plastic changes in experimental groups as compared with the control group (developmental as well as adult acclimation) revealed significant accumulation of body lipids owing to thermal or humidity acclimation of wet season flies, but low humidity acclimation did not change the level of body lipids in dry season flies. Starvation resistance and body lipids were higher in the males of dry season flies but in the females of wet season flies. Adults acclimated under different thermal or humidity conditions exhibited changes in the rate of utilization of body lipids, carbohydrates and proteins. Adult acclimation of wet or dry season flies revealed plastic changes in mean daily fecundity; and a reduction in fecundity under starvation. Thus, thermal or humidity acclimation of adults revealed plastic changes in energy metabolites to support starvation resistance of wet or dry season flies. © 2018. Published by The Company of Biologists Ltd.

Comparison of Anastrepha ludens (Diptera: Tephritidae) Bisexual and Genetic Sexing (Tapachula-7) Strains: Effect of Hypoxia, Fly Density, Chilling Period, and Food Type on Fly Quality.

PubMed

Arredondo, José; Ruiz, Lía; Hernández, Emilio; Montoya, Pablo; Díaz-Fleischer, Francisco

2016-04-01

The use of genetic sexing strain (GSS) insects in the sterile insect technique (SIT) makes necessary the revision of quality parameters of some stressful steps used during the packing process for aerial release because of possible differences in tolerance between fly strains. Here, we determined the effect of three periods of hypoxia (12, 24, and 36 h at pupal stage), three cage densities (1.0, 1.3, and 1.5 flies/cm2), two different foods (protein/sugar (1/24) and Mubarqui), and three chilling times (20 min [control], 90, and 180 min) on the quality parameters of flies of two Anastrepha ludens (Loew) strains (bisexual and GSS Tapachula-7). In general, the response to stressful conditions of both fly strains was qualitatively equivalent but quantitatively different, as flies of both strains responded equally to the stressful factors; however, flies of Tapachula-7 exhibited lower quality parameters than the control flies. Thus, hypoxia affected the flying ability but not the emergence or longevity of flies. The food type affected the adult weight; protein/sugar produced heavier flies that also survived longer and had a greater mating propensity. Flies under the lowest density were better fliers that those at the other two densities. Increasing chilling time reduced flight ability but not longevity or mating propensity. The implications of these findings for the use of A. ludens GSS in SIT programs are discussed herein.

Two NASA Dryden F/A-18s flown by Gordon Fullerton and Nils Larson fly in tight formation Dec. 21, 2007 during Fullerton's final flight before his retirement.

NASA Image and Video Library

2007-12-21

Long-time NASA Dryden research pilot and former astronaut C. Gordon Fullerton capped an almost 50-year flying career, including more than 38 years with NASA, with a final flight in a NASA F/A-18 on Dec. 21, 2007. Fullerton and Dryden research pilot Jim Smolka flew a 90-minute pilot proficiency formation aerobatics flight with another Dryden F/A-18 and a Dryden T-38 before concluding with two low-level formation flyovers of Dryden before landing. Fullerton was honored with a water-cannon spray arch provided by two fire trucks from the Edwards Air Force Base fire department as he taxied the F/A-18 up to the Dryden ramp, and was then greeted by his wife Marie and several hundred Dryden staff after his final flight. Fullerton began his flying career with the U.S. Air Force in 1958 after earning bachelor's and master's degrees in mechanical engineering from the California Institute of Technology. Initially trained as a fighter pilot, he later transitioned to multi-engine bombers and became a bomber operations test pilot after attending the Air Force Aerospace Research Pilot School at Edwards Air Force Base, Calif. He then was assigned to the flight crew for the planned Air Force Manned Orbital Laboratory in 1966. Upon cancellation of that program, the Air Force assigned Fullerton to NASA's astronaut corps in 1969. He served on the support crews for the Apollo 14, 15, 16 and 17 lunar missions, and was later assigned to one of the two flight crews that piloted the space shuttle prototype Enterprise during the Approach and Landing Test program at Dryden. He then logged some 382 hours in space when he flew on two early space shuttle missions, STS-3 on Columbia in 1982 and STS-51F on Challenger in 1985. He joined the flight crew branch at NASA Dryden after leaving the astronaut corps in 1986. During his 21 years at Dryden, Fullerton was project pilot on a number of high-profile research efforts, including the Propulsion Controlled Aircraft, the high-speed landing tests of

A Long-Term Experimental Case Study of the Ecological Effectiveness and Cost Effectiveness of Invasive Plant Management in Achieving Conservation Goals: Bitou Bush Control in Booderee National Park in Eastern Australia

PubMed Central

Lindenmayer, David B.; Wood, Jeff; MacGregor, Christopher; Buckley, Yvonne M.; Dexter, Nicholas; Fortescue, Martin; Hobbs, Richard J.; Catford, Jane A.

2015-01-01

Invasive plant management is often justified in terms of conservation goals, yet progress is rarely assessed against these broader goals, instead focussing on short-term reductions of the invader as a measure of success. Key questions commonly remain unanswered including whether invader removal reverses invader impacts and whether management itself has negative ecosystem impacts. We addressed these knowledge gaps using a seven year experimental investigation of Bitou Bush, Chrysanthemoides monilifera subsp. rotundata. Our case study took advantage of the realities of applied management interventions for Bitou Bush to assess whether it is a driver or passenger of environmental change, and quantified conservation benefits relative to management costs of different treatment regimes. Among treatments examined, spraying with herbicide followed by burning and subsequent re-spraying (spray-fire-spray) proved the most effective for reducing the number of individuals and cover of Bitou Bush. Other treatment regimes (e.g. fire followed by spraying, or two fires in succession) were less effective or even exacerbated Bitou Bush invasion. The spray-fire-spray regime did not increase susceptibility of treated areas to re-invasion by Bitou Bush or other exotic species. This regime significantly reduced plant species richness and cover, but these effects were short-lived. The spray-fire-spray regime was the most cost-effective approach to controlling a highly invasive species and facilitating restoration of native plant species richness to levels characteristic of uninvaded sites. We provide a decision tree to guide management, where recommended actions depend on the outcome of post-treatment monitoring and performance against objectives. Critical to success is avoiding partial treatments and treatment sequences that may exacerbate invasive species impacts. We also show the value of taking advantage of unplanned events, such as wildfires, to achieve management objectives at reduced cost. PMID:26039730

Persistence behavior of imidacloprid and carbosulfan in mango (Mangifera indica L.).

PubMed

Bhattacherjee, A K

2013-02-01

Imidacloprid was sprayed on mango cv. Dashehari at 0.3 mL L(-1) of water during pre-bloom stage with 6-8 cm panicle size (first week of March) to control hopper and carbosulfan was sprayed at 2.0 mL L(-1) of water in the trees of mango hybrid (H-1000) during fruit development stage (first week of May) to control leaf webber. Residues of both the insecticides were analysed in peel, pulp and fruit at different stages of fruit development and maturity. The initial residues of imidacloprid, after 30 days of spraying, were 1.21, 0.56 and 1.77 mg kg(-1) in peel, pulp and whole fruit, respectively. The residues persisted in peel for 60 days and in pulp for 50 days and dissipated with a half-life of 38 days. Mature Dashehari fruits at harvest (after 85 days of spraying) were free from imidacloprid residues. Carbosulfan in mango peel dissipated from 5.30 mg kg(-1) (after 1 h of spraying) to 0.05 mg kg(-1) at the time of harvest (after 45 days of spraying). Carbosulfan residue in pulp was very low (0.08 mg kg(-1)) after 1 h of spraying, which increased gradually to 0.90 mg kg(-1) after 10 days and finally came down to 0.04 mg kg(-1) after 26 days of spraying. The insecticide residue was not detected in the pulp at the time of harvest. The residues persisted in pulp for 26 days and in peel for 45 days and degraded with a half-life of 7 days. The dissipation of both imidacloprid and carbosulfan followed first order rate kinetics in whole fruit (peel + pulp). Therefore, the safe pre-harvest intervals were suggested to be 55 days for imidacloprid and 46 days for carbosulfan before consumption of mango fruits after spraying of these insecticides.

A long-term experimental case study of the ecological effectiveness and cost effectiveness of invasive plant management in achieving conservation goals: bitou bush control in booderee national park in eastern australia.

PubMed

Lindenmayer, David B; Wood, Jeff; MacGregor, Christopher; Buckley, Yvonne M; Dexter, Nicholas; Fortescue, Martin; Hobbs, Richard J; Catford, Jane A

2015-01-01

Invasive plant management is often justified in terms of conservation goals, yet progress is rarely assessed against these broader goals, instead focussing on short-term reductions of the invader as a measure of success. Key questions commonly remain unanswered including whether invader removal reverses invader impacts and whether management itself has negative ecosystem impacts. We addressed these knowledge gaps using a seven year experimental investigation of Bitou Bush, Chrysanthemoides monilifera subsp. rotundata. Our case study took advantage of the realities of applied management interventions for Bitou Bush to assess whether it is a driver or passenger of environmental change, and quantified conservation benefits relative to management costs of different treatment regimes. Among treatments examined, spraying with herbicide followed by burning and subsequent re-spraying (spray-fire-spray) proved the most effective for reducing the number of individuals and cover of Bitou Bush. Other treatment regimes (e.g. fire followed by spraying, or two fires in succession) were less effective or even exacerbated Bitou Bush invasion. The spray-fire-spray regime did not increase susceptibility of treated areas to re-invasion by Bitou Bush or other exotic species. This regime significantly reduced plant species richness and cover, but these effects were short-lived. The spray-fire-spray regime was the most cost-effective approach to controlling a highly invasive species and facilitating restoration of native plant species richness to levels characteristic of uninvaded sites. We provide a decision tree to guide management, where recommended actions depend on the outcome of post-treatment monitoring and performance against objectives. Critical to success is avoiding partial treatments and treatment sequences that may exacerbate invasive species impacts. We also show the value of taking advantage of unplanned events, such as wildfires, to achieve management objectives at reduced cost.

Control of Rhagoletis indifferents using Thiamethoxam and Spinosad baits under external fly pressure and its relation to rapidity of kill and residual bait activity

USDA-ARS?s Scientific Manuscript database

Control of western cherry fruit fly (Rhagoletis indifferens Curran) using thiamethoxam in sucrose bait and spinosad bait in cherry orchards under external fly pressure and its relation to rapidity of kill and residual bait activity were studied in Washington and Utah in 2010 and 2011. Thiamethoxam ...

Biological and Cultural Control of Olive Fruit Fly in California---Utilization of Parasitoids from USDA-APHIS-PPQ, Guatemala

USDA-ARS?s Scientific Manuscript database

The parasitoid Psytallia cf. concolor (Szépligeti) was reared on sterile Mediterranean fruit fly larvae at the USDA-APHIS-PPQ, Petapa Quarantine Laboratory in Guatemala and shipped to the USDA-ARS, Parlier, for wide-spread release and biological control of olive fruit fly in California. As many as 3...

Temporal Diversity and Abundance Patterns of Parasitoids of Fruit-Infesting Tephritidae (Diptera) in the Argentinean Yungas: Implications for Biological Control.

PubMed

Schliserman, Pablo; Aluja, Martin; Rull, Juan; Ovruski, Sergio M

2016-10-01

A 4-yr study was done to analyze seasonal patterns underlying host plant-fruit fly-parasitoid interactions in a secondary forest in the Argentinean Yunga and its importance for the implementation of conservation and augmentative biological control. Larval-pupal hymenopteran parasitoids associated with all host plants and fruit fly species were identified and the seasonal occurrence of fruit, infestation levels, parasitism percentage, and relative parasitoid abundance were determined. Three fruit fly species in two genera were found in association with surveyed plants, two of which (Ceratitis capitata (Wiedemann) and Anastrepha fraterculus (Wiedemann)) are of major economic importance. Infestation levels were strongly influenced by environmental factors and peak fruit availability. Five fruit fly parasitoid species were recovered from fly pupae, four braconid species, and one figitid. Time windows for fruit fly population growth were pinpointed. Based on results, the present analysis proposes an effective fruit fly biological control strategy tailored for the northwestern Argentinean citrus-producing area. © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Choice of optimal biocide combination to control flies (Diptera: Muscidae).

PubMed

Kavran, Mihaela; Zgomba, Marija F; Ignjatovic-Ćupina, Aleksandra M; Lazić, Sanja D; Petrić, Dušan V

2015-01-01

Flies - by feeding on decaying matter, human waste and food - have been implicated in the spread of numerous animal and human diseases. Excessive fly populations are generally associated with livestock units and domestic waste due to decaying organic matter. A large number of flies cause extreme disturbance in the behavior of the host, resulting in skin irritation, lesions, wounds, and secondary infections are likely to appear. The aim of this study was to evaluate the effects of combined applications of larvicide (cyromazine) and adulticides (acetamiprid in formulation with pheromone and thiamethoxam) on the suppression of fly populations. The study was conducted on a pig farm. The piglet farms are one of the most favorable places for fly breeding. Three units were used for biocide applications and a fourth unit as the control where biocides were not applied. The monitoring of pre- and post-treatment of adult fly populations was carried out by glued cardboards. The cards were hung on metal rods above piglet's cage. This monitoring method served as a parameter for the estimation of biological effectiveness. The highest degree of fly control (88.4% mortality 8 days after treatment) was achieved when a combination of cyromazine and thiamethoxam was used. A biocide based on sex pheromone (Z)-9-tricosene + acetamiprid was the most effective on flies 3 days after biocide application, with a mortality rate of 69.1 %. Thiamethoxam achieved the highest reduction of flies 6 days after treatment, with 78.19% obtained mortality. Biological efficacy of the applied biocides in combination ciromazine + thiamethoxam and thiamethoxam alone was justified.

Droplet Sizing Research.

DTIC Science & Technology

1985-04-15

studies, The measurement volume is defined by the intersection aerosol studies, flue gas desulfurization , spray drying, of apertures in front of two...identify by block numberl --A method to measure the size and velocity of individual particles in a flow is discussed. Results are presented for controlled ... controlled m0 monodisperse sprays and compared to flash photographs. Typical errors between predicted and measured sizes are less than 5%. Experimental

Droplet size and velocity distributions for spray modelling

NASA Astrophysics Data System (ADS)

Jones, D. P.; Watkins, A. P.

2012-01-01

Methods for constructing droplet size distributions and droplet velocity profiles are examined as a basis for the Eulerian spray model proposed in Beck and Watkins (2002,2003) [5,6]. Within the spray model, both distributions must be calculated at every control volume at every time-step where the spray is present and valid distributions must be guaranteed. Results show that the Maximum Entropy formalism combined with the Gamma distribution satisfy these conditions for the droplet size distributions. Approximating the droplet velocity profile is shown to be considerably more difficult due to the fact that it does not have compact support. An exponential model with a constrained exponent offers plausible profiles.

PRN 2001-X Draft: Spray and Dust Drift Label Statements for Pesticide Products

EPA Pesticide Factsheets

This Notice sets forth the U.S. Environmental Protection Agency's (EPA or Agency) draft guidance for labeling statements for controlling spray drift and dust drift from application sites and for implementing these statements for risk mitigation.

DDT spray for control of the ponderosa pine tip moth (Rhyacionia zozana [Kearfott])

Treesearch

Robert E. Stevens

1965-01-01

A water emulsion spray of DDT applied by hand sprayer to young trees infested with eggs and early-instar larvae of the ponderosa pine tip moth halted further larval activity and effectively prevented all damage.

Dimethyl sulfoxide therapy in bronchiolitis.

PubMed

Zúñiga, A; Burdach, R; Rubio, S

1975-01-27

The action of a medicinal spray that contains anti-inflammatory and bacterio-static drugs integrated with the penetrating and potentiating agent DMSO has been evaluated clinically in 60 infants with acute respiratory obstruction. A dose of 2 ml of this spray is applied in the posterior pharynx and the tonsil region; 1 to 4 applications are made, according to the clinical evolution of the case. Two groups were chosen at random; 60 patients were paired off, and one of each pair received the treatment with DMSO spray. All the patients received ampicillin (50-100 mg/kg body weight). The following clinical results were observed. First there was an immediate recovery, after an average lapse of 30 min; improvement of sensorial involvement was observed in 80% of the cases, reduction of the intercostal retraction in 75%, reduction of polypnea in 76%, and transformation of the obstructive syndrome into a catarrhal syndrome in 80% (with fluidification of the secretions, which were expelled more easily by the upper air tracts). There was also a deferred or maintenance effect, which evaluated in comparsion with the control group that received similar treatment except for the nebulizations with DMSO spray. A sequential design, based on whether or not it was necessary to use the croupette, demonstrated the superiority of the DMSO spray over the control treatment in the bronchiolar process; in the group treated with DMSO spray it was not necessary to use the croupette. The sequential design based on the effect of this therapy on the general condition and the tabulated clinical factors permitted the inference that the therapeutic responses are more favorable in the group treated with DMSO spray than in the control group. In the sequential design, the line of significance is cut at the fifteenth pair (an error of 0.05 and P equals 0.95%). Since the application is easy, there are no toxic side effects and in view of the favorable results in the clinical evolution of the acute respiratory obstructive processes, we consider the use of this therapeutic spray very useful and beneficial in bronchiolitis.

Integrated pest management of two-spotted mite Tetranychus urticae on greenhouse roses using petroleum spray oil and the predatory mite Phytoseiulus persimilis.

PubMed

Nicetic; Watson, D M; Beattie, G A; Meats, A; Zheng, J

2001-01-01

From 1995 to 1999, four experiments were conducted on greenhouse roses to assess the effectiveness of the nC24 petroleum spray oil (PSO), D-C-Tron Plus, against two-spotted mite, Tetranychus urticae Koch (Acarina: Tetranychidae), and to determine how the oil could be most efficiently and effectively used in combination with the predatory mite Phytoseiulus persimilis Athias-Henriot (Acarina: Phytoseiidae) in an integrated pest management program. The results showed that 0.5% PSO applied fortnightly to roses gave excellent protection from T urticae infestation when the mite population was not already established. However, PSO applied after roses were infested with T. urticae above the economic threshold only stabilised populations without reducing them below that threshold. Populations of P. persimilis in the upper and lower canopies were unchanged after two sprays of PSO at 7-day intervals, and application of PSO to the upper canopy was as effective in controlling T. urticae in the presence of P persimilis as spraying the entire plant. Combining PSO with P. persimilis gave better control of T. urticae than using P. persimilis alone. The most cost-effective use of PSO in the presence of P. persimilis is, therefore, to apply spray only to the upper canopy. This will not affect control of powdery mildew with PSO. Comparison of a control program for T urticae based on the monitored use of synthetic miticides with that based on calendar application of PSO revealed that both gave equally effective control. The benefits of combining PSO and P. persimilis in an integrated pest management program for T. urticae on roses over a program based on synthetic fungicides are discussed.

Biochemical composition and antioxidant activity affected by spraying potassium sulfate in black grape (Vitis vinifera L. cv. Rasha).

PubMed

Zareei, Elnaz; Javadi, Taimoor; Aryal, Rishi

2018-04-27

The physiological and metabolic processes involved with grapevine growth and production are influenced by key macro and micro-nutrients. Potassium is an essential plant nutrient that affects growth and fruit quality. In this study, the impact of foliar spraying of potassium sulfate (K 2 SO 4 ) on qualitative characteristics of grape berries was evaluated in the cultivar 'Rasha', a commonly cultivated cultivar in Kurdistan province of Iran. Leaves of the fully-grown vines were sprayed with each of the 1.5 g L -1 and 3 g L -1 potassium sulfate solution once (one month after petal senescence) and twice (15 days after first spraying). The control plants were sprayed with distilled water. Various biochemical content and enzyme activities on the ripe berries were analyzed. Significant increase in anthocyanin, total protein content and antioxidant enzyme activities were observed in the berries treated twice with 3 g L -1 K 2 SO 4 . Concentrations of total carbohydrate, phenol and antioxidant activity in berries sprayed with K 2 SO 4 were higher compared to the controls. We observed a strong correlation between antioxidant activity and different phenolic compounds. These findings suggest that K 2 SO 4 treatment influences biosynthesis of phenolic compounds and antioxidant enzymes. Thus treatment by K 2 SO 4 could improve nutritional and qualitative attributes of grape. This article is protected by copyright. All rights reserved.

Effects of Five Ayurvedic Herbs on Locomotor Behaviour in a Drosophila melanogaster Parkinson’s Disease Model

PubMed Central

Jansen, R. L. M.; Brogan, B.; Whitworth, A. J.; Okello, E. J.

2015-01-01

Current conventional treatments for Parkinson’s disease (PD) are aimed at symptom management, as there is currently no known cure or treatment that can slow down its progression. Ayurveda, the ancient medical system of India, uses a combination of herbs to combat the disease. Herbs commonly used for this purpose are Zandopa (containing Mucuna pruriens), Withania somnifera, Centella asiatica, Sida cordifolia and Bacopa monnieri. In this study, these herbs were tested for their potential ability to improve climbing ability of a fruit fly (Drosophila melanogaster) PD model based on loss of function of phosphatase and tensin-induced putative kinase 1 (PINK1). Fruit flies were cultured on food containing individual herbs or herbal formulations, a combination of all five herbs, levodopa (positive control) or no treatment (negative control). Tests were performed in both PINK1 mutant flies and healthy wild-type (WT) flies. A significant improvement in climbing ability was observed in flies treated with B. monnieri compared with untreated PINK1 mutant flies. However, a significant decrease in climbing ability was observed in WT flies for the same herb. Centella asiatica also significantly decreased climbing ability in WT flies. No significant effects were observed with any of the other herbs in either PINK1 or WT flies compared with untreated flies. PMID:25091506

Impact of house fly salivary gland hypertrophy virus (MdSGHV) on a heterologous host, Stomoxys calcitrans

USDA-ARS?s Scientific Manuscript database

The effect of Musca domestica salivary gland hypertrophy virus (MdSGHV) on selected fitness parameters of stable flies (Stomoxys calcitrans [L.]) was examined in the laboratory. Virus-injected stable flies of both genders suffered substantially higher mortality than control flies. By day 9, female...

Effects of pyriproxyfen and buprofezin on immature development, female oviposition, and egg-hatching in the stable fly

USDA-ARS?s Scientific Manuscript database

The stable fly, Stomoxys calcitrans (L.) (Diptera: Muscidae), is one of the most economically significant biting flies affecting cattle. Use of traditional insecticides have only limited success in control of stable flies largely due to the stable fly’s unique feeding behaviors and immature developm...

Mechanism of resistance to synthetic pyrethroids in buffalo flies in south-east Queensland

USDA-ARS?s Scientific Manuscript database

Buffalo fly (Haematobia irritans exigua) and horn fly (Haematobia irritans irritans) cause irritation and production loss in much of the cattle producing area of the world. In Australia losses from buffalo fly were recently estimated at A$78m per year. Control is largely performed by using organoph...

Preliminary studies developing methods for the control of Chrysomya putoria, the African latrine fly, in pit latrines in The Gambia

PubMed Central

Lindsay, T C; Jawara, M; D'Alessandro, U; Pinder, M; Lindsay, S W

2013-01-01

Objective To explore ways of controlling Chrysomya putoria, the African latrine fly, in pit latrines. As pit latrines are a major source of these flies, eliminating these important breeding sites is likely to reduce village fly populations, and may reduce the spread of diarrhoeal pathogens. Methods We treated 24 latrines in a Gambian village: six each with (i) pyriproxyfen, an insect juvenile hormone mimic formulated as Sumilarv® 0.5G, a 0.5% pyriproxyfen granule, (ii) expanded polystyrene beads (EPB), (iii) local soap or (iv) no treatment as controls. Flies were collected using exit traps placed over the drop holes, weekly for five weeks. In a separate study, we tested whether latrines also function as efficient flytraps using the faecal odours as attractants. We constructed six pit latrines each with a built-in flytrap and tested their catching efficiency compared to six fish-baited box traps positioned 10 m from the latrine. Focus group discussions conducted afterwards assessed the acceptability of the flytrap latrines. Results Numbers of emerging C. putoria were reduced by 96.0% (95% CIs: 94.5–97.2%) 4–5 weeks after treatment with pyriproxyfen; by 64.2% (95% CIs: 51.8–73.5%) after treatment with local soap; by 41.3% (95% CIs = 24.0–54.7%) after treatment with EPB 3–5 weeks after treatment. Flytraps placed on latrines collected C. putoria and were deemed acceptable to local communities. Conclusions Sumilarv 0.5G shows promise as a chemical control agent, whilst odour-baited latrine traps may prove a useful method of non-chemical fly control. Both methods warrant further development to reduce fly production from pit latrines. A combination of interventions may prove effective for the control of latrine flies and the diseases they transmit. PMID:23198767

Composite-Metal-Matrix Arc-Spray Process

NASA Technical Reports Server (NTRS)

Westfall, Leonard J.

1987-01-01

Arc-spray "monotape" process automated, low in cost, and produces at high rate. Ideal for development of new metal-matrix composites. "Monotape" reproducible and of high quality. Process carried out in controlled gas environment with programmable matrix-deposition rates, resulting in significant cost saving

PAINT SPRAY BOOTH MODIFICATIONS FOR RECIRCULATION VENTILATION

EPA Science Inventory

The control of emissions from spray painting operations has historically been cost prohibitive, due to the high exhaust flow rates coupled with low volatile organic compound (VOC) and hazardous air pollutant (HAP) Concentrations. Past studies, conducted by the U.S. EPA and U.S. ...

Spray characteristics affected by physical properties of adjuvants

USDA-ARS?s Scientific Manuscript database

Four drift adjuvants, Array, In-Place, Vector and Control, were tested and physical properties and spray spectrum parameters measured. Array had the highest conductivity, indicating a good potential for the electrostatic charging, and the highest shear viscosity. All adjuvants had very similar neut...

Producing Quantum Dots by Spray Pyrolysis

NASA Technical Reports Server (NTRS)

Banger, Kulbinder; Jin, Michael H.; Hepp, Aloysius

2006-01-01

An improved process for making nanocrystallites, commonly denoted quantum dots (QDs), is based on spray pyrolysis. Unlike the process used heretofore, the improved process is amenable to mass production of either passivated or non-passivated QDs, with computer control to ensure near uniformity of size.

The importance of ecological studies in the control of tsetse flies*

PubMed Central

Glover, P. E.

1967-01-01

The author reviews recent ecological research on tsetse flies in East Africa and Northern Nigeria, particularly in connexion with the flies' sensory reactions, and stresses the importance of an accurate knowledge of their daytime and night-time resting-sites and of identifying the sources of their blood meals in order to elucidate the reservoirs of trypanosomiasis. The epidemiology of the disease is considered in the light of studies of trypanosome infections in host and fly. The control of tsetse flies must be based on the practical application of ecological knowledge by methods involving either a direct attack upon the fly (such as trapping or the use of insecticides) or an indirect attack (such as bush clearing or game destruction to eliminate the fly's habitat or food supply); these methods are dealt with in some detail. The author concludes with a discussion of modern trends in research, and a number of lines of research are suggested. PMID:4874781

Production of lightweight aggregates from mining residues, heavy metal sludge, and incinerator fly ash.

PubMed

Huang, Su-Chen; Chang, Fang-Chih; Lo, Shang-Lien; Lee, Ming-Yu; Wang, Chu-Fang; Lin, Jyh-Dong

2007-06-01

In this study, artificial lightweight aggregate (LWA) manufactured from recycled resources was investigated. Residues from mining, fly ash from an incinerator and heavy metal sludge from an electronic waste water plant were mixed into raw aggregate pellets and fed into a tunnel kiln to be sintered and finally cooled rapidly. Various feeding and sintering temperatures were employed to examine their impact on the extent of vitrification on the aggregate surface. Microstructural analysis and toxicity characteristic leaching procedure (TCLP) were also performed. The results show that the optimum condition of LWA fabrication is sintering at 1150 degrees C for 15 min with raw aggregate pellets fed at 750 degrees C. The rapidly vitrified surface envelops the gas produced with the increase in internal temperature and cooling by spraying water prevents the aggregates from binding together, thus forming LWA with specific gravity of 0.6. LWA produced by sintering in tunnel kiln shows good vitrified surface, low water absorption rate below 5%, and low cylindrical compressive strength of 4.3 MPa. In addition, only trace amounts of heavy metals were detected, making the LWA non-hazardous for construction use.

Hydrodynamic Qualities of a 1/10-Size Powered Dynamic Model of the XP5Y-1 Flying Boat in Smooth Water: Langley Tank Model 246, TED No. NACA DE 320

NASA Technical Reports Server (NTRS)

Woodward, David R.; Weinstein, Irving; Whitaker, Walter E., Jr.

1947-01-01

The hydrodynamic characteristics of a 1/10-size powered dynamic model of the XP5Y-1 flying boat were determined in Langley tank no. 1. Stable take-offs were possible at all practicable positions of the center of gravity and flap deflections. An increase in gross load from 123.5 to 150.0 pounds (21.5 percent) had only a slight effect on the stable range for take-off. A decrease in forward acceleration from 3.0 to 1.0 feet per second per second had only a very small effect on the stable range for take-off. In general, the landings were free from skipping except at trims below 6 deg where one skip was encountered at an aft position of the center of gravity. The model porpoised during the landing runout at all positions of the center of gravity when landed at trims above 10 deg. Spray in the propellers was light at the design gross load, and was not considered excessive,at a gross load of 136.0 pounds.

Modification of the solid-state nature of sulfathiazole and sulfathiazole sodium by spray drying.

PubMed

Bianco, Stefano; Caron, Vincent; Tajber, Lidia; Corrigan, Owen I; Nolan, Lorraine; Hu, Yun; Healy, Anne Marie

2012-06-01

Solid-state characterisation of a drug following pharmaceutical processing and upon storage is fundamental to successful dosage form development. The aim of the study was to investigate the effects of using different solvents, feed concentrations and spray drier configuration on the solid-state nature of the highly polymorphic model drug, sulfathiazole (ST) and its sodium salt (STNa). The drugs were spray-dried from ethanol, acetone and mixtures of these organic solvents with water. Additionally, STNa was spray-dried from pure water. The physicochemical properties including the physical stability of the spray-dried powders were compared to the unprocessed materials. Spray drying of ST from either acetonic or ethanolic solutions with the spray drier operating in a closed cycle mode yielded crystalline powders. In contrast, the powders obtained from ethanolic solutions with the spray drier operating in an open cycle mode were amorphous. Amorphous ST crystallised to pure form I at ≤35 % relative humidity (RH) or to polymorphic mixtures at higher RH values. The usual crystal habit of form I is needle-like, but spherical particles of this polymorph were generated by spray drying. STNa solutions resulted in an amorphous material upon processing, regardless of the solvent and the spray drier configuration employed. Moisture induced crystallisation of amorphous STNa to a sesquihydrate, whilst crystallisation upon heating gave rise to a new anhydrous polymorph. This study indicated that control of processing and storage parameters can be exploited to produce drugs with a specific/desired solid-state nature.

Effect of emulsification and spray-drying microencapsulation on the antilisterial activity of transcinnamaldehyde.

PubMed

Trinh, Nga-Thi-Thanh; Lejmi, Raja; Gharsallaoui, Adem; Dumas, Emilie; Degraeve, Pascal; Thanh, Mai Le; Oulahal, Nadia

2015-01-01

Spray-dried redispersible transcinnamaldehyde (TC)-in-water emulsions were prepared in order to preserve its antibacterial activity; 5% (w/w) TC emulsions were first obtained with a rotor-stator homogeniser in the presence of either soybean lecithin or sodium caseinate as emulsifiers. These emulsions were mixed with a 30% (w/w) maltodextrin solution before feeding a spray-dryer. The antibacterial activity of TC alone, TC emulsions with and without maltodextrin before and after spray-drying were assayed by monitoring the growth at 30 °C of Listeria innocua in their presence and in their absence (control). Whatever the emulsifier used, antilisterial activity of TC was increased following its emulsification. However, reconstituted spray-dried emulsions stabilised by sodium caseinate had a higher antibacterial activity suggesting that they better resisted to spray-drying. This was consistent with observation that microencapsulation efficiencies were 27.6% and 78.7% for emulsions stabilised by lecithin and sodium caseinate, respectively.

Liquid sprays and flow studies in the direct-injection diesel engine under motored conditions

NASA Technical Reports Server (NTRS)

Nguyen, Hung Lee; Carpenter, Mark H.; Ramos, Juan I.; Schock, Harold J.; Stegeman, James D.

1988-01-01

A two dimensional, implicit finite difference method of the control volume variety, a two equation model of turbulence, and a discrete droplet model were used to study the flow field, turbulence levels, fuel penetration, vaporization, and mixing in diesel engine environments. The model was also used to study the effects of engine speed, injection angle, spray cone angle, droplet distribution, and intake swirl angle on the flow field, spray penetration and vaporization, and turbulence in motored two-stroke diesel engines. It is shown that there are optimum conditions for injection, which depend on droplet distribution, swirl, spray cone angle, and injection angle. The optimum conditions result in good spray penetration and vaporization and in good fuel mixing. The calculation presented clearly indicates that internal combustion engine models can be used to assess, at least qualitatively, the effects of injection characteristics and engine operating conditions on the flow field and on the spray penetration and vaporization in diesel engines.

Spray characteristics of two combined jet atomizers

NASA Astrophysics Data System (ADS)

Tambour, Y.; Portnoy, D.

The downstream changes in droplet volume concentration of a vaporizing fuel spray produced by two jet atomizers which form an overlapping zone of influence is theoretically analyzed, employing experimental data of Yule et al. (1982) for a single jet atomizer as initial conditions. One of the atomizers is located below the other at a certain distance downstream. Such an injection geometry can be found in afterburners of modern jet engines. The influence of various vertical and horizontal distances between the two atomizers on the downstream spray characteristics is investigated for a vaporizing kerosene spray in a 'cold' (293 K) and a 'hot' (450 K) environment. The analysis shows how one can control the downstream spray characteristics via the geometry of injection. Such geometrical considerations may be of great importance in the design of afterburner wall geometry and in the reduction of wall thermal damage. The injection geometry may also affect the intensity of the spray distribution which determines the mode of droplet group combustion. The latter plays an important role in improving afterburner combustion efficiency.

Thermal Spray Applications in Electronics and Sensors: Past, Present, and Future

NASA Astrophysics Data System (ADS)

Sampath, Sanjay

2010-09-01

Thermal spray has enjoyed unprecedented growth and has emerged as an innovative and multifaceted deposition technology. Thermal spray coatings are crucial to the enhanced utilization of various engineering systems. Industries, in recognition of thermal spray's versatility and economics, have introduced it into manufacturing environments. The majority of modern thermal spray applications are "passive" protective coatings, and they rarely perform an electronic function. The ability to consolidate dissimilar material multilayers without substrate thermal loading has long been considered a virtue for thick-film electronics. However, the complexity of understanding/controlling materials functions especially those resulting from rapid solidification and layered assemblage has stymied expansion into electronics. That situation is changing: enhancements in process/material science are allowing reconsideration for novel electronic/sensor devices. This review critically examines past efforts in terms of materials functionality from a device perspective, along with ongoing/future concepts addressing the aforementioned deficiencies. The analysis points to intriguing future possibilities for thermal spray technology in the world of thick-film sensors.

Efficacy of proactive long-term maintenance therapy of canine atopic dermatitis with 0.0584% hydrocortisone aceponate spray: a double-blind placebo controlled pilot study.

PubMed

Lourenço, Ana M; Schmidt, Vanessa; São Braz, Berta; Nóbrega, Diana; Nunes, Telmo; Duarte-Correia, José H; Matias, Daniela; Maruhashi, Emi; Rème, Christophe A; Nuttall, Tim

2016-04-01

Long-term remission between flares of canine atopic dermatitis (CAD) can be difficult to achieve. Therefore, additional strategic forms of treatment are needed in order to target flare prevention. The concept of proactive therapy is recommended in the European guidelines for the treatment of human atopic eczema. To evaluate the efficacy of a proactive treatment regimen with a 0.0584% hydrocortisone aceponate (HCA) spray for CAD. Client-owned dogs with spontaneous atopic dermatitis (AD) (n = 41). This pilot study was conducted as a randomised, placebo-controlled, double-blinded clinical trial with an end-point of treatment failure. Dogs were treated once daily to remission, then randomly assigned to receive either the HCA spray (n = 21) or a placebo (n = 20) spray on two consecutive days each week. All dogs were on appropriate flea control. No topical or systemic anti-inflammatory or antimicrobial agents were permitted. Intention-to-treat analysis was used. At Day 0, all the dogs were in remission or had mild AD based on their Canine Atopic Dermatitis Extent and Severity Index, version 3 (CADESI-03) scores. The time to relapse was significantly higher in the HCA group (median 115 d; range 31-260 d) compared to the placebo group (median 33 d; range 15-61 d) (P < 0.0001). No adverse events were attributable to the HCA spray. Four dogs were lost to follow-up and four were withdrawn after receiving prohibited medication. These results indicate that proactive long-term therapy of CAD with an HCA spray administered on two consecutive days each week is effective and well-tolerated. © 2016 ESVD and ACVD.

In Vivo Laser Cartilage Reshaping with Carbon Dioxide Spray Cooling in a Rabbit Ear Model: A Pilot Study

PubMed Central

Kuan, Edward C.; Hamamoto, Ashley A.; Sun, Victor; Nguyen, Tony; Manuel, Cyrus T.; Protsenko, Dmitry E.; Wong, Brian J.F.; Nelson, J. Stuart; Jia, Wangcun

2014-01-01

BACKGROUND/OBJECTIVES Similar to conventional cryogen spray cooling, carbon dioxide (CO2) spray may be used in combination with laser cartilage reshaping (LCR) to produce cartilage shape change while minimizing cutaneous thermal injury. Recent ex vivo evaluation of LCR with CO2 cooling in a rabbit model has identified a promising initial parameter space for in vivo safety and efficacy evaluation. This pilot study aimed to evaluate shape change and cutaneous injury following LCR with CO2 cooling in 5 live rabbits. STUDY DESIGN/MATERIALS AND METHODS The midportion of live rabbit ears were irradiated with a 1.45 μm wavelength diode laser (12 J/cm2) with simultaneous CO2 spray cooling (85 ms duration, 4 alternating heating/cooling cycles per site, 5 to 6 irradiation sites per row for 3 rows per ear). Experimental and control ears (no LCR) were splinted in the flexed position for 30 days following exposure. A total of 5 ears each were allocated to the experimental and control groups. RESULTS Shape change was observed in all irradiated ears (mean 70 ± 3°), which was statistically different from control (mean 37 ± 11 °, p = 0.009). No significant thermal cutaneous injury was observed, with preservation of the full thickness of skin, microvasculature, and adnexal structures. Confocal microscopy and histology demonstrated an intact and viable chondrocyte population surrounding irradiated sites. CONCLUSIONS LCR with CO2 spray cooling can produce clinically significant shape change in the rabbit auricle while minimizing thermal cutaneous and cartilaginous injury and frostbite. This pilot study lends support for the potential use of CO2 spray as an adjunct to existing thermal-based cartilage reshaping modalities. An in vivo systematic evaluation of optimal laser dosimetry and cooling parameters is required. PMID:25557008

Toxicity of spray and fumigant products containing cassia oil to Dermatophagoides farinae and Dermatophagoides pteronyssinus (Acari: Pyroglyphidae).

PubMed

Kim, Soon-Ii; Kim, Hyun-Kyung; Koh, Young-Yull; Clark, J Marshall; Ahn, Young-Joon

2006-08-01

The toxicity of formulations of oil of cassia, Cinnamomum cassia Blume, (20 and 50 g L(-1) sprays and 100% oil-based fumigant) to adult Dermatophagoides farinae Hughes and D. pteronyssinus Trouessart was examined using contact and vapour-phase toxicity bioassays. Results were compared with the lethal activity of three commercial acaricides: benzyl benzoate, dibutyl phthalate and diethyl-m-toluamide (deet). The contact toxicity of cassia oil to both dust mite species was comparable with that of benzyl benzoate but was higher than that of the other two acaricides. Sprays containing 20 and 50 g L(-1) cassia oil were effective against both mite species when applied to fabric, glass, paper, plastic, tin or wood substrates. Applications of the 50 g L(-1) spray to different space volumes and surface areas determined that 50-60 mg of cassia oil was needed to control dust mites in 3.4 m(3) or in 1 m(2). In tests with fumigant devices, toxicity varied according to the thickness of non-woven fabric covering the device, the exposure time, the number of fumigant devices used and the volume of the space sprayed. Fumigant toxicity to adult D. pteronyssinus was more pronounced with devices enclosed in thinner (40 microm) versus thicker (45 or 50 microm) non-woven fabric covers. A single fumigant device with a 40 microm thick non-woven fabric cover resulted in substantial control in a space of 0.05 m(3) but exhibited only moderate to weak control in spaces >or= 0.097 m(3) at 4 days after application. Two fumigant devices gave 88% mortality in a space of 1.73 m(3). Cassia oil applied as sprays or in fumigant devices appears to provide effective protection of humans from house dust mites.

Experimental analysis of pressure controlled atomization process (PCAP) coatings for replacement of hard chromium plating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tierney, J.C.; Glovan, R.J.; Witt, S.J.

1995-12-31

A four-phase experimental design was utilized to evaluate the abrasive wear and corrosion protection characteristics of VERSAlloy 50 coatings applied to AISI 4130 steel sheet. The coatings were applied with the Pressure Controlled Atomization Process (PCAP), a new thermal spray process being developed for the United States Air Force to replace hard chromium plating. Phase 1 of the design consisted of an evaluation of deposit profiles that were sprayed at five different standoff distances. Profile measurements yielded standard deviations ({sigma}) of the plume at each of the spray distances. Phase 2 consisted of a completely randomized series of eight spraymore » tests in which the track gap or distance between consecutive spray passes was varied by amounts of 0.5{sigma}, 1{sigma}, 2{sigma}, and 3{sigma}. The sprayed test coupons were then evaluated for corrosion protection, abrasive wear resistance, microhardness, and porosity. Results from Phase 2 were used to determine the best track gap or overlap for Phase 3 and Phase 4 testing. Phase 3 consisted of 22-run central composite design. The test coupons were evaluated the same as in Phase 2. Statistical analysis of Phase 3 data revealed that the optimal system operating parameters produced coatings that would either provide superior corrosion protection or resistance to abrasive wear. Phase 4 consisted of four spray tests to validate the results obtained in Phase 3. Phase 4 test coupons were again evaluated with the same analysis as in Phases 2 and 3. The validation tests indicated that PCAP system operating parameters could be controlled to produce VERSAlloy 50 coatings with superior corrosion protection or resistance to abrasive wear.« less

Basal streamline sprays for hardwood resprout control: herbicides, concentrations, and streaks per stem

Treesearch

James H. Miller

1997-01-01

Basal streamline sprays were tested to control sweetgum, water oak, and southern red oak that ranged from 0.5 to 2 inches groundline diameter. Primary test herbicides and mixtures were triclopyr (Garlon 4) at 20 and 40 percent mixed with 10 percent d-limonene (Cide-Kick) and the remainder diesel; and imazapyr (Chopper) at 5 and 10 percent mixed in only diesel. Primary...

[Experimental evaluation of the spraying disinfection efficiency on dental models].

PubMed

Zhang, Yi; Fu, Yuan-fei; Xu, Kan

2013-08-01

To evaluate the disinfect effect after spraying a new kind of disinfectant on the dental plaster models. The germ-free plaster samples, which were smeared with bacteria compound including Staphylococcus aureus, Escherichia coli, Saccharomyces albicans, Streptococcus mutans and Actinomyces viscosus were sprayed with disinfectants (CaviCide) and glutaraldehyde individually. In one group(5 minutes later) and another group(15 minutes later), the colonies were counted for statistical analysis after sampling, inoculating, and culturing which were used for evaluation of disinfecting efficiency. ANOVA was performed using SPSS12.0 software package. All sample bacteria were eradicated after spraying disinfectants(CaviCide) within 5 minutes and effective bacteria control was retained after 15 minutes. There was significant difference between the disinfecting efficiency of CaviCide and glutaraldehyde. The effect of disinfection with spraying disinfectants (CaviCide) on dental models is quick and effective.

The N.A.C.A. Photographic Apparatus for Studying Fuel Sprays from Oil Engine Injection Valves and Test Results from Several Researches

NASA Technical Reports Server (NTRS)

Beardsley, Edward G

1928-01-01

Apparatus for recording photographically the start, growth, and cut-off of oil sprays from injection valves has been developed at the Langley Memorial Aeronautical Laboratory. The apparatus consists of a high-tension transformer by means of which a bank of condensers is charged to a high voltage. The controlled discharge of these condensers in sequence, at a rate of several thousand per second, produces electric sparks of sufficient intensity to illuminate the moving spray for photographing. The sprays are injected from various types of valves into a chamber containing gases at pressures up to 600 pounds per square inch. Several series of pictures are shown. The results give the effects of injection pressure, chamber pressure, specific gravity of the fuel oil used, and injection-valve design, upon spray characteristics.

Delivery systems for biological control agents to manage aflatoxin contamination of pre-harvest maize.

PubMed

Lyn, M E; Abbas, H K; Zablotowicz, R M; Johnson, B J

2009-03-01

While soil application of a competitive non-toxigenic Aspergillus flavus strains is successful in reducing aflatoxin contamination in certain crops, direct application to aerial reproductive structures could be more effective for maize. A sprayable, clay-based water-dispersible granule formulation was developed to deliver non-toxigenic A. flavus strain K49 directly to maize ears. The efficacy of the K49 water-dispersible granule in mitigating aflatoxin in maize (Zea mays L.) was evaluated. Field studies were conducted to compare K49 colonization and effectiveness in reducing aflatoxin contamination when applied either as a soil inoculant or as a directed spray in plots infested with toxigenic strain F3W4. Fifty percent of non-toxigenic A. flavus was recovered from non-treated controls and from plots soil inoculated with K49 on wheat. In spray treatments with formulated or unformulated K49 conidia, over 90% of A. flavus recovered was non-toxigenic. Soil-applied K49 reduced aflatoxin contamination by 65% and spray applications reduced contamination by 97%. These findings suggest direct spray application of non-toxigenic A. flavus strains may be better than soil inoculation at controlling maize aflatoxin contamination and that a water-dispersible granule is a viable delivery system for maintaining viability and efficacy of the biological control agent, K49.

Comparisons of topical and spray applications of two pesticides, triazophos and jinggangmycin, on the protein content in the ovaries and fat bodies of the brown planthopper Nilaparvata lugens Stål (Hemiptera:Delphacidae).

PubMed

Zhu, Zhan-Fei; Cheng, Jia; Lu, Xiu-Li; Li, Xin; Ge, Lin-Quan; Fang, Ji-Chao; Wu, Jin-Cai

2014-09-01

The pesticide-induced stimulation of reproduction in pests is one of the most important mechanisms of pest resurgence. There have been numerous reports on the insecticide-induced stimulation of reproduction. However, the relationship between pesticide application method and pest resurgence (stimulation of reproduction) has received little attention. Here, we studied the effect of two treatment methods, triazophos (TZP) and jinggangmycin (JGM), on the protein content in the ovaries and fat bodies of the brown planthopper (BPH) Nilaparvata lugens Stål. The results showed that pesticide treatment methods significantly affected the protein content in the ovaries and fat bodies of BPH. In addition, grand means (means of main effect) of the protein content at 2 and 3 days after emergence (2 and 3 DAE) for foliar sprays was significantly higher than that observed after topical treatments, which increased by 23.9% (from 1.42 to 1.76) and 8.82% (from 4.42 to 4.81), respectively. No significant differences on the protein content in the ovaries and fat bodies for the JGM topical treatment were observed compared with controls. However, the protein content for JGM foliar sprays was significantly higher than that for the controls. The protein contents in both topical and spray treatments of TZP were significantly higher than those of the controls. Ovarian protein is mainly yolk protein. There is a positive correlation between ovarian protein content and the number of eggs laid. These findings show that foliar spray of the pesticides promotes the resurgence of BPH. Therefore, the foliar spray of some pesticides, such as JGM, should be avoided for the control of pests, which is the sideeffects of the fungicide on non-target insect pests' occurrence. Copyright © 2014 Elsevier Inc. All rights reserved.

Field evaluation of a botanical formulation from the milky mangrove Excoecaria agallocha L. against Helicoverpa armigera Hübner. in Abelmoschus esculentus (lady's finger) and Cajanus cajan (pigeon pea).

PubMed

Santhanam, Satyan Ramachandran; Egigu, Meseret C

2014-09-01

To evaluate a formulation from the milky mangrove tree Excoecaria agallocha L. (E. agallocha) against Helicoverpa armigera Hubner (H. armigera). About 3% aqueous ethanolic spray formulation derived from the lipophilic extract of E. agallocha (dry leaf) was evaluated against H. armigera in Abelmoschus esculentus (lady's finger) and Cajanus cajan (C. cajan) (pigeon pea), under field conditions. On the 9th day of the 4th spray the larval count in the plot treated with 3% E. agallocha formulation drastically came down to 0.23 larva/plant, compared to 1.63 in the ethanol control plot and 1.60 in the unsprayed plot. Blocks sprayed with 3% E. agallocha formulation yielded 35.8 quintals/hectare (q/ha) of healthy pods compared to Ekalux® (pod yield: 60.7 q/ha), 3% Vijay Neem® (60.22 q/ha), yield plot (6 q/ha) and ethanol control (7 q/ha). In C. cajan, 1% E. agallocha, 3% Nimbecidine® and 0.07% indoxacarb were equally potent in reducing the larval population of H. armigera and the non-target pest Spilosoma obliqua to 0%, from the 9th day (3rd spray). Indoxacarb plot recorded the maximum yield of 16.1 q/ha with 2.4% pod damage. Plots sprayed with 1% E. agallocha yielded 14.7 q/ha with 2.32% pod damage. The effect of 3% Nimbecidine® spray (14.35 q/ha) was comparable to E. agallocha formulation. Unsprayed and ethanol control plots yielded 12.41 and 11.2 q/ha of pods with an average pod damage of 4.7%. E. agallocha formulation was found to be promising for the control of H. armigera, under field conditions. Copyright © 2014 Hainan Medical College. Published by Elsevier B.V. All rights reserved.

Selective and conventional house-spraying of DDT and bendiocarb against Anopheles pseudopunctipennis in southern Mexico.

PubMed

Casas, M; Torres, J L; Bown, D N; Rodríguez, M H; Arredondo-Jiménez, J I

1998-12-01

Indoor feeding behaviors and mortalities of Anopheles pseudopunctipennis females were evaluated following contact with selective (bands covering mosquitoes' preferred resting areas) and full applications of DDT and bendiocarb on indoor sprayable surfaces. The DDT residues provoked strong avoidance behavior. To a lesser degree, mosquitoes were also repelled by bendiocarb-sprayed surfaces. Because of strong irritancy/repellency, unfed mosquitoes were driven outdoors in proportionally higher numbers. The resting time on selectively or fully DDT-sprayed huts was greatly reduced in comparison to bendiocarb-sprayed huts. Although unfed mosquitoes tended to rest on non-DDT-sprayed surfaces in the selectively treated hut, the man-biting rate was similar with both types of treatments. Unfed mosquitoes were repelled less from selectively bendiocarb-treated surfaces. Similar reductions in postfed resting times were observed on all surfaces suggesting that once fed, mosquitoes rested on sprayed surfaces for shorter intervals of time. Engorged mosquitoes had normal resting behavior (pre- and postspray) within the range of preferred resting heights in both DDT- and bendiocarb-sprayed huts, but the proportion of mosquitoes fed in the DDT-treated huts was lower. Selective spraying of walls was as effective as spraying the complete walls with both insecticides, but DDT was more effective in reducing mosquito-human contact. These studies show that by more effectively targeting vector behavior, a cost-effective alternative to traditional control techniques can be achieved.

Development of autonomous controller system of high speed UAV from simulation to ready to fly condition

NASA Astrophysics Data System (ADS)

Yudhi Irwanto, Herma

2018-02-01

The development of autonomous controller system that is specially used in our high speed UAV, it’s call RKX-200EDF/TJ controlled vehicle needs to be continued as a step to mastery and to developt control system of LAPAN’s satellite launching rocket. The weakness of the existing control system in this high speed UAV needs to be repaired and replaced using the autonomous controller system. Conversion steps for ready-to-fly system involved controlling X tail fin, adjusting auto take off procedure by adding X axis sensor, procedure of way points reading and process of measuring distance and heading to the nearest way point, developing user-friendly ground station, and adding tools for safety landing. The development of this autonomous controller system also covered a real flying test in Pandanwangi, Lumajang in November 2016. Unfortunately, the flying test was not successful because the booster rocket was blown right after burning. However, the system could record the event and demonstrated that the controller system had worked according to plan.

Clinical efficacy of a spray containing hyaluronic Acid and dexpanthenol after surgery in the nasal cavity (septoplasty, simple ethmoid sinus surgery, and turbinate surgery).

PubMed

Gouteva, Ina; Shah-Hosseini, Kija; Meiser, Peter

2014-01-01

Background. This prospective, controlled, parallel-group observational study investigated the efficacy of a spray containing hyaluronic acid and dexpanthenol to optimise regular treatment after nasal cavity surgery in 49 patients with chronic rhinosinusitis. Methods. The control group received standard therapy. Mucosal regeneration was determined using rhinoscopy sum score (RSS). Pre- and postoperative nasal patency was tested using anterior rhinomanometry. The participants were questioned about their symptoms. Results. Regarding all RSS parameters (dryness, dried nasal mucus, fibrin deposition, and obstruction), mucosal regeneration achieved good final results in both groups, tending to a better improvement through the spray application, without statistically significant differences during the whole assessment period, the mean values being 7.04, 5.00, 3.66, and 3.00 (intervention group) and 7.09, 5.14, 4.36, and 3.33 (control group). No statistically significant benefit was identified for nasal breathing, foreign body sensation, and average rhinomanometric volume flow, which improved by 12.31% (control group) and 11.24% (nasal spray group). Conclusion. The investigational product may have additional benefit on postoperative mucosal regeneration compared to standard cleaning procedures alone. However, no statistically significant advantage could be observed in this observational study. Double-blind, controlled studies with larger populations will be necessary to evaluate the efficacy of this treatment modality.

Clinical Efficacy of a Spray Containing Hyaluronic Acid and Dexpanthenol after Surgery in the Nasal Cavity (Septoplasty, Simple Ethmoid Sinus Surgery, and Turbinate Surgery)

PubMed Central

2014-01-01

Background. This prospective, controlled, parallel-group observational study investigated the efficacy of a spray containing hyaluronic acid and dexpanthenol to optimise regular treatment after nasal cavity surgery in 49 patients with chronic rhinosinusitis. Methods. The control group received standard therapy. Mucosal regeneration was determined using rhinoscopy sum score (RSS). Pre- and postoperative nasal patency was tested using anterior rhinomanometry. The participants were questioned about their symptoms. Results. Regarding all RSS parameters (dryness, dried nasal mucus, fibrin deposition, and obstruction), mucosal regeneration achieved good final results in both groups, tending to a better improvement through the spray application, without statistically significant differences during the whole assessment period, the mean values being 7.04, 5.00, 3.66, and 3.00 (intervention group) and 7.09, 5.14, 4.36, and 3.33 (control group). No statistically significant benefit was identified for nasal breathing, foreign body sensation, and average rhinomanometric volume flow, which improved by 12.31% (control group) and 11.24% (nasal spray group). Conclusion. The investigational product may have additional benefit on postoperative mucosal regeneration compared to standard cleaning procedures alone. However, no statistically significant advantage could be observed in this observational study. Double-blind, controlled studies with larger populations will be necessary to evaluate the efficacy of this treatment modality. PMID:25104962

Visceral Leishmaniasis in China: an Endemic Disease under Control

PubMed Central

Wu, Ming-Shui; Chen, Yun-Fu; Wang, Jun-Yun; Zhou, Xiao-Nong; Liao, Li-Fu; Chen, Jian-Ping; Chow, Larry M. C.

2015-01-01

SUMMARY Visceral leishmaniasis (VL) caused by Leishmania spp. is an important vector-borne and largely zoonotic disease. In China, three epidemiological types of VL have been described: anthroponotic VL (AVL), mountain-type zoonotic VL (MT-ZVL), and desert-type ZVL (DT-ZVL). These are transmitted by four different sand fly species: Phlebotomus chinensis, P. longiductus, P. wui, and P. alexandri. In 1951, a detailed survey of VL showed that it was rampant in the vast rural areas west, northwest, and north of the Yangtze River. Control programs were designed and implemented stringently by the government at all administrative levels, resulting in elimination of the disease from most areas of endemicity, except the western and northwestern regions. The control programs consisted of (i) diagnosis and chemotherapy of patients, (ii) identification, isolation, and disposal of infected dogs, and (iii) residual insecticide indoor spraying for vector control. The success of the control programs is attributable to massive and effective mobilization of the general public and health workers to the cause. Nationally, the annual incidence is now very low, i.e., only 0.03/100,000 according to the available 2011 official record. The overwhelming majority of cases are reported from sites of endemicity in the western and northwestern regions. Here, we describe in some depth and breadth the current status of epidemiology, diagnosis, treatment, and prevention of the disease, with particular reference to the control programs. Pertinent information has been assembled from scattered literature of the past decades in different languages that are not readily accessible to the scientific community. The information provided constitutes an integral part of our knowledge on leishmaniasis in the global context and will be of special value to those interested in control programs. PMID:26354822

Visceral Leishmaniasis in China: an Endemic Disease under Control.

PubMed

Lun, Zhao-Rong; Wu, Ming-Shui; Chen, Yun-Fu; Wang, Jun-Yun; Zhou, Xiao-Nong; Liao, Li-Fu; Chen, Jian-Ping; Chow, Larry M C; Chang, Kwang Poo

2015-10-01

Visceral leishmaniasis (VL) caused by Leishmania spp. is an important vector-borne and largely zoonotic disease. In China, three epidemiological types of VL have been described: anthroponotic VL (AVL), mountain-type zoonotic VL (MT-ZVL), and desert-type ZVL (DT-ZVL). These are transmitted by four different sand fly species: Phlebotomus chinensis, P. longiductus, P. wui, and P. alexandri. In 1951, a detailed survey of VL showed that it was rampant in the vast rural areas west, northwest, and north of the Yangtze River. Control programs were designed and implemented stringently by the government at all administrative levels, resulting in elimination of the disease from most areas of endemicity, except the western and northwestern regions. The control programs consisted of (i) diagnosis and chemotherapy of patients, (ii) identification, isolation, and disposal of infected dogs, and (iii) residual insecticide indoor spraying for vector control. The success of the control programs is attributable to massive and effective mobilization of the general public and health workers to the cause. Nationally, the annual incidence is now very low, i.e., only 0.03/100,000 according to the available 2011 official record. The overwhelming majority of cases are reported from sites of endemicity in the western and northwestern regions. Here, we describe in some depth and breadth the current status of epidemiology, diagnosis, treatment, and prevention of the disease, with particular reference to the control programs. Pertinent information has been assembled from scattered literature of the past decades in different languages that are not readily accessible to the scientific community. The information provided constitutes an integral part of our knowledge on leishmaniasis in the global context and will be of special value to those interested in control programs. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Protecting chickens against coccidiosis in floor pens by administering Eimeria oocysts using gel beads or spray vaccination.

PubMed

Jenkins, Mark C; Parker, Carolyn; O'Brien, Celia; Persyn, Joseph; Barlow, Darren; Miska, Katarzyna; Fetterer, Raymond

2013-09-01

Control of avian coccidiosis is increasingly being achieved by the administration of low doses of Eimeria oocysts to newly hatched chicks. The purpose of this study was to test the efficacy of gel beads containing a mixture of Eimeria acervulina, Eimeria maxima, and Eimeria tenella oocysts as a vaccine to protect broilers raised in contact with litter. Newly hatched chicks were either sprayed with an aqueous suspension of Eimeria oocysts or were allowed to ingest feed containing Eimeria oocysts-incorporated gel beads. Control, 1-day-old chicks were given an equivalent number of Eimeria oocysts (10(3) total) by oral gavage or received no vaccine (nonimmunized controls). All chicks were raised in floor-pen cages in direct contact with litter. At 4 wk of age, all chickens and a control nonimmunized group received a high-dose E. acervulina, E. maxima, and E. tenella challenge infection. Chickens immunized with Eimeria oocysts in gel beads or by spray vaccination displayed significantly (P < 0.05) greater weight gain (WG) compared to nonimmunized controls. Feed conversion ratio (FCR) also showed a significant (P < 0.05) improvement in both groups relative to nonimmunized controls. Moreover, WG and FCR in both groups was not significantly different (P > 0.05) from chickens immunized by oral gavage or from nonimmunized, noninfected controls. Oocyst excretion after Eimeria challenge by all immunized groups was about 10-fold less than in nonimmunized controls. These findings indicate that immunization efficacy of gel beads and spray vaccination is improved by raising immunized chicks in contact with litter.

Study of insect succession and rate of decomposition on a partially burned pig carcass in an oil palm plantation in Malaysia.

PubMed

Heo, Chong Chin; Mohamad, Abdullah Marwi; Ahmad, Firdaus Mohd Salleh; Jeffery, John; Kurahashi, Hiromu; Omar, Baharudin

2008-12-01

Insects found associated with corpse can be used as one of the indicators in estimating postmortem interval (PMI). The objective of this study was to compare the stages of decomposition and faunal succession between a partially burnt pig (Sus scrofa Linnaeus) and natural pig (as control). The burning simulated a real crime whereby the victim was burnt by murderer. Two young pigs weighed approximately 10 kg were used in this study. Both pigs died from pneumonia and immediately placed in an oil palm plantation near a pig farm in Tanjung Sepat, Selangor, Malaysia. One pig was partially burnt by 1-liter petrol while the other served as control. Both carcasses were visited twice per day for the first week and once thereafter. Adult flies and larvae on the carcasses were collected and later processed in a forensic entomology laboratory. Results showed that there was no significant difference between the rate of decomposition and sequence of faunal succession on both pig carcasses. Both carcasses were completely decomposed to remain stage after nine days. The species of flies visiting the pig carcasses consisted of blow flies (Chrysomya megacephala, Chrysomya rufifacies, Hemipyrellia ligurriens), flesh fly (Sarcophagidae.), muscid fly (Ophyra spinigera), soldier fly (Hermetia illucens), coffin fly (Phoridae) and scavenger fly (Sepsidae). The only difference noted was in the number of adult flies, whereby more flies were seen in the control carcass. Faunal succession on both pig carcasses was in the following sequence: Calliphoridae, Sarcophagidae, Muscidae, Phoridae and lastly Stratiomyidae. However, there was overlap in the appearance of members of these families. Blowflies continued to oviposit on both carcasses. Hence postmortem interval (PMI) can still be estimated from the partially burnt pig carcass.

A New Flying Wire System for the Tevatron

NASA Astrophysics Data System (ADS)

Blokland, Willem; Dey, Joseph; Vogel, Greg

1997-05-01

A new Flying Wires system replaces the old system to enhance the analysis of the beam emittance, improve the reliability, and handle the upcoming upgrades of the Tevatron. New VME data acquisition modules and timing modules allow for more bunches to be sampled more precisely. The programming language LabVIEW, running on a Macintosh computer, controls the VME modules and the nuLogic motion board that flies the wires. LabVIEW also analyzes and stores the data, and handles local and remote commands. The new system flies three wires and fits profiles of 72 bunches to a gaussian function within two seconds. A new console application operates the flying wires from any control console. This paper discusses the hardware and software setup, the capabilities and measurement results of the new Flying Wires system.

Positive Influence of Behavior Change Communication on Knowledge, Attitudes, and Practices for Visceral Leishmaniasis/Kala-azar in India.

PubMed

Srinivasan, Raghavan; Ahmad, Tanwir; Raghavan, Vidya; Kaushik, Manisha; Pathak, Ramakant

2018-03-21

Visceral leishmaniasis (VL) is endemic to 54 districts in 4 states of India. Poor awareness of the disease and inappropriate health-seeking behavior are major challenges to eliminating the disease. Between February 2016 and March 2017, we implemented a behavior change communication (BCC) intervention in 33 districts of Bihar, 4 districts of Jharkhand, and 3 districts of West Bengal using a mix of channels, including group and interpersonal communication, to improve knowledge, attitudes, and practices of communities, frontline health workers, and opinion leaders. We conducted an impact assessment in October 2016, after the second indoor residual spraying (IRS) round, in Bihar and Jharkhand to evaluate the effect of the BCC intervention. Villages in 10 districts of Bihar and 4 districts in Jharkhand were selected for inclusion in the assessment. Selected villages were categorized as either intervention or control based on where project activities were conducted. Households were randomly selected proportional to caste composition, and interviewers surveyed the head of the household on whether the house was sprayed during the last IRS round and on knowledge, attitudes, and practices related to VL. We interviewed 700 households in intervention villages and 350 households in control villages and conducted correlation analysis to explore the association between IRS refusal and socioeconomic variables, and tested for association between IRS refusal and exposure to BCC activities. Odds ratios (ORs) were calculated. We reached an estimated 3.3 million contacts in Bihar and Jharkhand through the intervention's BCC activities. IRS refusal rates were significantly lower in intervention households than control households (mean=7.95% vs. 24.45%, respectively; OR, 0.27; 95% confidence interval [CI], 0.11 to 0.62; P <.001). Households in intervention villages were more aware than those in control villages that VL is spread by sand flies (68.4% vs. 7.4%, respectively; P <.001) and of IRS as an effective control measure (82.3% vs. 41.7%, respectively; P <.001). A greater percentage of households in intervention villages than control villages indicated they would encourage a patient to go to primary health centers for diagnosis and treatment of VL (77.0% vs. 39.4%, respectively) and to encourage others to accept IRS (78.6% vs. 44.6%, respectively; P <.001). Households that were exposed to community-based BCC activities largely using group and interpersonal communication had better knowledge, attitudes, and practices related to VL, including acceptance of IRS as a preventive measure, than households not exposed. BCC activities are thus an important component of VL elimination strategies. © Srinivasan et al.

Mapping the benefit-cost ratios of interventions against bovine trypanosomosis in Eastern Africa.

PubMed

Shaw, A P M; Wint, G R W; Cecchi, G; Torr, S J; Mattioli, R C; Robinson, T P

2015-12-01

This study builds upon earlier work mapping the potential benefits from bovine trypanosomosis control and analysing the costs of different approaches. Updated costs were derived for five intervention techniques: trypanocides, targets, insecticide-treated cattle, aerial spraying and the release of sterile males. Two strategies were considered: continuous control and elimination. For mapping the costs, cattle densities, environmental constraints, and the presence of savannah or riverine tsetse species were taken into account. These were combined with maps of potential benefits to produce maps of benefit-cost ratios. The results illustrate a diverse picture, and they clearly indicate that no single technique or strategy is universally profitable. For control using trypanocide prophylaxis, returns are modest, even without accounting for the risk of drug resistance but, in areas of low cattle densities, this is the only approach that yields a positive return. Where cattle densities are sufficient to support it, the use of insecticide-treated cattle stands out as the most consistently profitable technique, widely achieving benefit-cost ratios above 5. In parts of the high-potential areas such as the mixed farming, high-oxen-use zones of western Ethiopia, the fertile crescent north of Lake Victoria and the dairy production areas in western and central Kenya, all tsetse control strategies achieve benefit-cost ratios from 2 to over 15, and for elimination strategies, ratios from 5 to over 20. By contrast, in some areas, notably where cattle densities are below 20per km(2), the costs of interventions against tsetse match or even outweigh the benefits, especially for control scenarios using aerial spraying or the deployment of targets where both savannah and riverine flies are present. If the burden of human African trypanosomosis were factored in, the benefit-cost ratios of some of the low-return areas would be considerably increased. Comparatively, elimination strategies give rise to higher benefit-cost ratios than do those for continuous control. However, the costs calculated for elimination assume problem-free, large scale operations, and they rest on the outputs of entomological models that are difficult to validate in the field. Experience indicates that the conditions underlying successful and sustained elimination campaigns are seldom met. By choosing the most appropriate thresholds for benefit-cost ratios, decision-makers and planners can use the maps to define strategies, assist in prioritising areas for intervention, and help choose among intervention techniques and approaches. The methodology would have wider applicability in analysing other disease constraints with a strong spatial component. Copyright © 2015 A.P.M Shaw. Published by Elsevier B.V. All rights reserved.

Controlled overspray spray nozzle

NASA Technical Reports Server (NTRS)

Prasthofer, W. P. (Inventor)

1981-01-01

A spray system for a multi-ingredient ablative material wherein a nozzle A is utilized for suppressing overspray is described. The nozzle includes a cyclindrical inlet which converges to a restricted throat. A curved juncture between the cylindrical inlet and the convergent portion affords unrestricted and uninterrupted flow of the ablative material. A divergent bell-shaped chamber and adjustable nozzle exit B is utilized which provides a highly effective spray pattern in suppressing overspray to an acceptable level and producing a homogeneous jet of material that adheres well to the substrate.

Comparison of the olfactory preferences of four species of filth fly pupal parasitoid species (Hymenoptera: Pteromalidae) for hosts in equine and bovine manure

USDA-ARS?s Scientific Manuscript database

House flies (Musca domestica L.) and stable flies (Stomoxys calcitrans (L.)) (Diptera: Muscidae) are common pests in equine and cattle facilities. Pupal parasitoids primarily in the genera Spalangia and Muscidifurax (Hymenoptera: Pteromalidae) can be purchased for biological control of these flies. ...

Whole genome sequencing of the Braconid parasitoid wasp Fopius arisanus, an important biocontrol agent of pest Tepritid fruit flies

USDA-ARS?s Scientific Manuscript database

The braconid wasp Fopius arisanus (Sonan) is an important biological control agent of tropical and subtropical pest fruit flies including two important global pests, the Mediterranean fruit fly (Ceratitis capitata), and the oriental fruit fly (Bactrocera dorsalis}). The goal of this study was to dev...

Dutch Elm Disease and Methoxychlor

Treesearch

Jack H. Barger

1976-01-01

American elm trees, Ulmus americana L., in Milwaukee, Wisconsin, were sprayed with methoxychlor by helicopter or mist blower once each year for 3 years to control the smaller European elm bark beetle Scolytus multistriatus (Marsham). Twig crotches were collected from sprayed trees each year for bioassay. Methoxychlor residues...

ENTRAINMENT BY LIGAMENT-CONTROLLED EFFERVESCENT ATOMIZER-PRODUCED SPRAYS

EPA Science Inventory

Entrainment of ambient air into sprays produced by a new type of effervescent atomizer is reported. Entrainment data were obtained using a device similar to that described by Ricou & Spalding (1961). Entrainment data were analyzed using the model of Bush & Sojka (1994), in concer...

Geopolymer concretes: a green construction technology rising from the ash

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allouche, E.

2009-07-01

Researchers at Louisiana Tech University have embarked on a multi-year research initiative to develop applications for inorganic polymer concrete, or geopolymer concrete, in the area of civil construction, and to bring solve of these applications to market. One objective was to produce a spray-on coating for use in the harsh environment of wastewater conveyance and treatment facilities. Another project is to establish relationships between fly ash composition and particle size distribution and the mechanical attributes and workability of the resulting geopolymer concrete. A third project is to develop a 'smart' geopolymer concrete whose response to a given electric current canmore » be correlated to the stress level to which the structure is subjected. 1 fig., 6 photos.« less

Combined control of morphology and polymorph in spray drying of mannitol for dry powder inhalation

NASA Astrophysics Data System (ADS)

Lyu, Feng; Liu, Jing J.; Zhang, Yang; Wang, Xue Z.

2017-06-01

The morphology and polymorphism of mannitol particles were controlled during spray drying with the aim of improving the aerosolization properties of inhalable dry powders. The obtained microparticles were characterized using scanning electron microscopy, infrared spectroscopy, differential scanning calorimetry, powder X-ray diffraction and inhaler testing with a next generation impactor. Mannitol particles of varied α-mannitol content and surface roughness were prepared via spray drying by manipulating the concentration of NH4HCO3 in the feed solution. The bubbles produced by NH4HCO3 led to the formation of spheroid particles with a rough surface. Further, the fine particle fraction was increased by the rough surface of carriers and the high α-mannitol content. Inhalable dry powders with a 29.1 ± 2.4% fine particle fraction were obtained by spray-drying using 5% mannitol (w/v)/2% NH4HCO3 (w/v) as the feed solution, proving that this technique is an effective method to engineer particles for dry powder inhalation.

Hardware-In-The-Loop Testing of Continuous Control Algorithms for a Precision Formation Flying Demonstration Mission

NASA Technical Reports Server (NTRS)

Naasz, Bo J.; Burns, Richard D.; Gaylor, David; Higinbotham, John

2004-01-01

A sample mission sequence is defined for a low earth orbit demonstration of Precision Formation Flying (PFF). Various guidance navigation and control strategies are discussed for use in the PFF experiment phases. A sample PFF experiment is implemented and tested in a realistic Hardware-in-the-Loop (HWIL) simulation using the Formation Flying Test Bed (FFTB) at NASA's Goddard Space Flight Center.

Minocycline, but not ascorbic acid, increases motor activity and extends the life span of Drosophila melanogaster.

PubMed

Mora, Marylhi; Medina-Leendertz, Shirley J; Bonilla, Ernesto; Terán, Raikelin E; Paz, Milagros C; Arcaya, José Luis

2013-06-01

In the present study we compared the effects of minocycline and ascorbic acid in the life span, motor activity and lipid peroxidation of Drosophila melanogaster, in an effort to find a substance capable of providing protection against oxidative stress in aging. In the flies treated with minocycline a very significant increase in the life span (101 +/- 1.33 days) was observed when compared to those treated with ascorbic acid and controls (42.3% and 38.4%, respectively). The motor activity of minocycline treated flies also increased significantly with respect to control and ascorbic acid fed flies, from the 3rd to the 9th week of treatment. With regard to lipid peroxidation, it was found that the levels of malondialdehyde (MDA) in flies treated with minocycline showed no statistical differences to the control on the first day of treatment, but a significantly lower content on the day of 50% survival. In contrast, in flies treated with ascorbic acid significantly elevated levels of MDA compared to control and minocycline treated flies were detected throughout. These results suggest a protective effect of minocycline against oxidative stress and aging in D. melanogaster. An inhibitory effect on reactive oxygen species production may be an important contributing factor.

Discovering the flight autostabilizer of fruit flies by inducing aerial stumbles

PubMed Central

Ristroph, Leif; Bergou, Attila J.; Ristroph, Gunnar; Coumes, Katherine; Berman, Gordon J.; Guckenheimer, John; Wang, Z. Jane; Cohen, Itai

2010-01-01

Just as the Wright brothers implemented controls to achieve stable airplane flight, flying insects have evolved behavioral strategies that ensure recovery from flight disturbances. Pioneering studies performed on tethered and dissected insects demonstrate that the sensory, neurological, and musculoskeletal systems play important roles in flight control. Such studies, however, cannot produce an integrative model of insect flight stability because they do not incorporate the interaction of these systems with free-flight aerodynamics. We directly investigate control and stability through the application of torque impulses to freely flying fruit flies (Drosophila melanogaster) and measurement of their behavioral response. High-speed video and a new motion tracking method capture the aerial “stumble,” and we discover that flies respond to gentle disturbances by accurately returning to their original orientation. These insects take advantage of a stabilizing aerodynamic influence and active torque generation to recover their heading to within 2° in < 60 ms. To explain this recovery behavior, we form a feedback control model that includes the fly’s ability to sense body rotations, process this information, and actuate the wing motions that generate corrective aerodynamic torque. Thus, like early man-made aircraft and modern fighter jets, the fruit fly employs an automatic stabilization scheme that reacts to short time-scale disturbances. PMID:20194789

Controlling free flight of a robotic fly using an onboard vision sensor inspired by insect ocelli

PubMed Central

Fuller, Sawyer B.; Karpelson, Michael; Censi, Andrea; Ma, Kevin Y.; Wood, Robert J.

2014-01-01

Scaling a flying robot down to the size of a fly or bee requires advances in manufacturing, sensing and control, and will provide insights into mechanisms used by their biological counterparts. Controlled flight at this scale has previously required external cameras to provide the feedback to regulate the continuous corrective manoeuvres necessary to keep the unstable robot from tumbling. One stabilization mechanism used by flying insects may be to sense the horizon or Sun using the ocelli, a set of three light sensors distinct from the compound eyes. Here, we present an ocelli-inspired visual sensor and use it to stabilize a fly-sized robot. We propose a feedback controller that applies torque in proportion to the angular velocity of the source of light estimated by the ocelli. We demonstrate theoretically and empirically that this is sufficient to stabilize the robot's upright orientation. This constitutes the first known use of onboard sensors at this scale. Dipteran flies use halteres to provide gyroscopic velocity feedback, but it is unknown how other insects such as honeybees stabilize flight without these sensory organs. Our results, using a vehicle of similar size and dynamics to the honeybee, suggest how the ocelli could serve this role. PMID:24942846

Recent advances in phlebotomine sand fly research related to leishmaniasis control.

PubMed

Bates, Paul A; Depaquit, Jerôme; Galati, Eunice A B; Kamhawi, Shaden; Maroli, Michele; McDowell, Mary Ann; Picado, Albert; Ready, Paul D; Salomón, O Daniel; Shaw, Jeffrey J; Traub-Csekö, Yara M; Warburg, Alon

2015-02-27

Phlebotomine sand flies are the subject of much research because of the role of their females as the only proven natural vectors of Leishmania species, the parasitic protozoans that are the causative agents of the neglected tropical disease leishmaniasis. Activity in this field was highlighted by the eighth International Symposium on Phlebotomine Sand flies (ISOPS) held in September 2014, which prompted this review focusing on vector control. Topics reviewed include: Taxonomy and phylogenetics, Vector competence, Genetics, genomics and transcriptomics, Eco-epidemiology, and Vector control. Research on sand flies as leishmaniasis vectors has revealed a diverse array of zoonotic and anthroponotic transmission cycles, mostly in subtropical and tropical regions of Africa, Asia and Latin America, but also in Mediterranean Europe. The challenge is to progress beyond descriptive eco-epidemiology, in order to separate vectors of biomedical importance from the sand fly species that are competent vectors but lack the vectorial capacity to cause much human disease. Transmission modelling is required to identify the vectors that are a public health priority, the ones that must be controlled as part of the integrated control of leishmaniasis. Effective modelling of transmission will require the use of entomological indices more precise than those usually reported in the leishmaniasis literature.

Dispersal of Rhagoletis cerasi in Commercial Cherry Orchards: Efficacy of Soil Covering Nets for Cherry Fruit Fly Control.

PubMed

Daniel, Claudia; Baker, Brian

2013-03-12

Demand for organic cherries offers producers a premium price to improve their commercial viability. Organic standards require that producers find alternatives to pesticides. Soil treatments to control the European cherry fruit fly Rhagoletis cerasi (L.) (Diptera: Tephrididae) appear to be an attractive option. However, soil treatments can only be effective if the migration of flies is low, because mature flies may migrate from near-by trees for oviposition. To examine the general potential of soil treatments and to understand the dispersal and flight behaviour of R. cerasi within orchards, experiments using netting to cover the soil were conducted in two orchards with different pest pressure during two years. The netting reduced flight activity by 77% and fruit infestation by 91%. The data showed that the flies have a dispersal of less than 5 m within orchards, which is very low. The low thresholds for tolerance for infested fruit in the fresh market creates a strong economic incentive for control, therefore, soil covering is a promising strategy for controlling R. cerasi in commercial orchards.

Dispersal of Rhagoletis cerasi in Commercial Cherry Orchards: Efficacy of Soil Covering Nets for Cherry Fruit Fly Control

PubMed Central

Daniel, Claudia; Baker, Brian

2013-01-01

Demand for organic cherries offers producers a premium price to improve their commercial viability. Organic standards require that producers find alternatives to pesticides. Soil treatments to control the European cherry fruit fly Rhagoletis cerasi (L.) (Diptera: Tephrididae) appear to be an attractive option. However, soil treatments can only be effective if the migration of flies is low, because mature flies may migrate from near-by trees for oviposition. To examine the general potential of soil treatments and to understand the dispersal and flight behaviour of R. cerasi within orchards, experiments using netting to cover the soil were conducted in two orchards with different pest pressure during two years. The netting reduced flight activity by 77% and fruit infestation by 91%. The data showed that the flies have a dispersal of less than 5 m within orchards, which is very low. The low thresholds for tolerance for infested fruit in the fresh market creates a strong economic incentive for control, therefore, soil covering is a promising strategy for controlling R. cerasi in commercial orchards. PMID:26466801

Quantitative X-ray measurements of high-pressure fuel sprays from a production heavy duty diesel injector

NASA Astrophysics Data System (ADS)

Ramírez, A. I.; Som, S.; Aggarwal, Suresh K.; Kastengren, A. L.; El-Hannouny, E. M.; Longman, D. E.; Powell, C. F.

2009-07-01

A quantitative and time-resolved X-ray radiography technique has been used for detailed measurements of high-pressure fuel sprays in the near-nozzle region of a diesel engine injector. The technique provides high spatial and temporal resolution, especially in the relatively dense core region. A single spray plume from a hydraulically actuated electronically controlled unit injector model 315B injector with a 6-hole nozzle was isolated and studied at engine-like densities for two different injection pressures. Optical spray imaging was also employed to evaluate the effectiveness of the shield used to isolate a single spray plume. The steady state fuel distributions for both injection pressures are similar and show a dense spray region along the axis of the spray, with the on-axis spray density decreasing as the spray progresses downstream. The higher injection pressure case exhibits a larger cone angle and spray broadening at the exit of the nozzle. For some time periods, the near-nozzle penetration speed is lower for the high injection pressure case than the low injection pressure case, which is unexpected, but can be attributed to the needle and flow dynamics inside the injector causing slower pressure build-up for the former case. Rate of injection testing was performed to further understand near-nozzle behavior. Mass distribution data were obtained and used to find mass-averaged velocity of the spray. Comparisons of the radiography data with that from a common rail single-hole light duty injectors under similar injection conditions show several significant differences. The current data show a larger cone angle and lower penetration speed than that from the light-duty injector. Moreover, these data display a Gaussian mass distribution across the spray near the injector, whereas in previous light-duty injector measurements, the mass distribution had steeper sides and a flatter peak. Measurements are also used to examine the spray models in the STAR-CD software.

Sublethal effects in pest management: a surrogate species perspective on fruit fly control

USDA-ARS?s Scientific Manuscript database

Tephritid fruit flies are economically important orchard pests globally. While much effort has focused on controlling individual species with a combination of pesticides and biological control, less attention has been paid to managing assemblages of species. Although several tephritid species may co...

DEVELOPMENT OF AN INNOVATIVE SPRAY DISPENSER TO REDUCE INDOOR AIR EMISSIONS FROM AEROSOL CONSUMER PRODUCTS

EPA Science Inventory

The report presents the operating principles and performance of a new type of spray nozzle. This nozzle, termed a "ligament-controlled effervescent atomizer," was developed to allow consumer product manufacturers to replace volatile organic compound (VOC) solvents with water, and...

Postplanting sprays of dalapon and atrazine to aid conifer establishment.

Treesearch

Edward J. Dimock; Ernest B. Collard

1981-01-01

A mixture of dalapon and atrazine consistently controlled grasses of forbs better than either herbicide used alone. Sprayed over and around newly planted ponderosa pine (Pinus ponderosa Dougl. ex Laws.) and Douglas-fir (Pseudotsuga menziesii var. glauca (Beissn.) Franco), the mixture doubled tree survival...

76 FR 16417 - Product Cancellation Order for Certain Pesticide Registrations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-23

...) Regulatory Public Docket in Rm. S- 4400, One Potomac Yard (South Bldg.), 2777 S. Crystal Dr., Arlington, VA... Shot Phenothrin Wasp & Hornet Tetramethrin Spray. 013283-00013 Rainbow Wasp & Ant Bioallethrin Spray... Neopynamim Tetramethrin Technical. 073510-00008 Marketquest One Permethrin Drop Flea & Tick Control-2. 082498...

Electrostatic application of antimicrobial sprays to sanitize food handling and processing surfaces for enhanced food safety

NASA Astrophysics Data System (ADS)

Lyons, Shawn M.; Harrison, Mark A.; Law, S. Edward

2011-06-01

Human illnesses and deaths caused by foodborne pathogens (e.g., Salmonella enterica, Listeria monocytogenes, Escherichia coli O157:H7, etc.) are of increasing concern globally in maintaining safe food supplies. At various stages of the food production, processing and supply chain antimicrobial agents are required to sanitize contact surfaces. Additionally, during outbreaks of contagious pathogenic microorganisms (e.g., H1N1 influenza), public health requires timely decontamination of extensive surfaces within public schools, mass transit systems, etc. Prior publications verify effectiveness of air-assisted, induction-charged (AAIC) electrostatic spraying of various chemical and biological agents to protect on-farm production of food crops...typically doubling droplet deposition efficiency with concomitant increases in biological control efficacy. Within a biosafety facility this present work evaluated the AAIC electrostatic-spraying process for application of antimicrobial liquids onto various pathogen-inoculated food processing and handling surfaces as a food safety intervention strategy. Fluoroanalysis of AAIC electrostatic sprays (-7.2 mC/kg charge-to-mass ratio) showed significantly greater (p<0.05) mass of tracer active ingredient (A.I.) deposited onto target surfaces at various orientations as compared both to a similar uncharged spray nozzle (0 mC/kg) and to a conventional hydraulic-atomizing nozzle. Per unit mass of A.I. dispensed toward targets, for example, A.I. mass deposited by AAIC electrostatic sprays onto difficult to coat backsides was 6.1-times greater than for similar uncharged sprays and 29.0-times greater than for conventional hydraulic-nozzle sprays. Even at the 56% reduction in peracetic acid sanitizer A.I. dispensed by AAIC electrostatic spray applications, they achieved equal or greater CFU population reductions of Salmonella on most target orientations and materials as compared to uncharged sprays and conventional full-rate hydraulic-nozzle sprays.

Modeling visual-based pitch, lift and speed control strategies in hoverflies

PubMed Central

Vercher, Jean-Louis

2018-01-01

To avoid crashing onto the floor, a free falling fly needs to trigger its wingbeats quickly and control the orientation of its thrust accurately and swiftly to stabilize its pitch and hence its speed. Behavioural data have suggested that the vertical optic flow produced by the fall and crossing the visual field plays a key role in this anti-crash response. Free fall behavior analyses have also suggested that flying insect may not rely on graviception to stabilize their flight. Based on these two assumptions, we have developed a model which accounts for hoverflies´ position and pitch orientation recorded in 3D with a fast stereo camera during experimental free falls. Our dynamic model shows that optic flow-based control combined with closed-loop control of the pitch suffice to stabilize the flight properly. In addition, our model sheds a new light on the visual-based feedback control of fly´s pitch, lift and thrust. Since graviceptive cues are possibly not used by flying insects, the use of a vertical reference to control the pitch is discussed, based on the results obtained on a complete dynamic model of a virtual fly falling in a textured corridor. This model would provide a useful tool for understanding more clearly how insects may or not estimate their absolute attitude. PMID:29361632

Sanitizer Efficacy against Murine Norovirus, a Surrogate for Human Norovirus, on Stainless Steel Surfaces when Using Three Application Methods

PubMed Central

Kotwal, Grishma; Harrison, Mark A.; Law, S. Edward; Harrison, Judy A.

2013-01-01

Human noroviruses are major etiologic agents of epidemic gastroenteritis. Outbreaks are often accompanied by contamination of environmental surfaces, but since these viruses cannot be routinely propagated in laboratory cultures, their response to surface disinfectants is predicted by using surrogates, such as murine norovirus 1 (MNV-1). This study compared the virucidal efficacies of various liquid treatments (three sanitizer liquids, 5% levulinic acid plus 2% SDS [LEV/SDS], 200 ppm chlorine, and an isopropanol-based quaternary ammonium compound [Alpet D2], and two control liquids, sterile tap water and sterile tap water plus 2% SDS) when delivered to MNV-1-inoculated stainless steel surfaces by conventional hydraulic or air-assisted, induction-charged (AAIC) electrostatic spraying or by wiping with impregnated towelettes. For the spray treatments, LEV/SDS proved effective when applied with hydraulic and AAIC electrostatic spraying, providing virus reductions of 2.71 and 1.66 log PFU/ml, respectively. Alpet D2 provided a 2.23-log PFU/ml reduction with hydraulic spraying, outperforming chlorine (1.16-log PFU/ml reduction). Chlorine and LEV/SDS were equally effective as wipes, reducing the viral load by 7.05 log PFU/ml. Controls reduced the viral load by <1 log with spraying applications and by >3 log PFU/ml with wiping. Results indicated that both sanitizer type and application methods should be carefully considered when choosing a surface disinfectant to best prevent and control environmental contamination by noroviruses. PMID:23263949

Sprayed intraperitoneal bupivacaine reduces early postoperative pain behavior and biochemical stress response after laparoscopic ovariohysterectomy in dogs.

PubMed

Kim, Young K; Lee, Scott S; Suh, Euy H; Lee, Lyon; Lee, Hee C; Lee, Hyo J; Yeon, Seong C

2012-02-01

This study investigated the use of sprayed intraperitoneal bupivacaine to relieve postoperative pain behavior and biochemical stress response after laparoscopic ovariohysterectomy (LOVH) in dogs. Sixteen sexually intact female dogs were randomly assigned to two groups. The sprayed intraperitoneal bupivacaine (SIB) group received 4.4 mg/kg of sprayed intraperitoneal bupivacaine diluted to 0.25% with an equivalent volume of saline after pneumoperitoneum. The control group received 1.76 mL/kg of saline in a similar fashion. Both groups received preoperative periportal 5% bupivacaine (1 mL) before incision. Postoperative pain was measured using the short form of the Glasgow composite measures pain scale (CMPS-SF, 0-24). Serum cortisol and glucose concentrations were measured preoperatively and 0.5, 1, 2, 4, 6, 12, and 24h postoperatively. The SIB group had significantly lower CMPS-SF compared to the control group 1, 2, 4, 6, and 12h after the operation. Cortisol concentrations were significantly increased from preoperative concentrations in the control group at 0.5, 1, 2, and 4h post operation and at 0.5 and 1h post operation in the SIB group. No significant differences were seen in serum glucose within each group. This report suggests that the use of sprayed intraperitoneal bupivacaine can be used as part of a multimodal approach for pain management after LOVH in dogs. Copyright © 2011 Elsevier Ltd. All rights reserved.

Alternative treatments for indoor residual spraying for malaria control in a village with pyrethroid- and DDT-resistant vectors in the Gambia.

PubMed

Tangena, Julie-Anne A; Adiamoh, Majidah; D'Alessandro, Umberto; Jarju, Lamin; Jawara, Musa; Jeffries, David; Malik, Naiela; Nwakanma, Davis; Kaur, Harparkash; Takken, Willem; Lindsay, Steve W; Pinder, Margaret

2013-01-01

Malaria vector control is threatened by resistance to pyrethroids, the only class of insecticides used for treating bed nets. The second major vector control method is indoor residual spraying with pyrethroids or the organochloride DDT. However, resistance to pyrethroids frequently confers resistance to DDT. Therefore, alternative insecticides are urgently needed. Insecticide resistance and the efficacy of indoor residual spraying with different insecticides was determined in a Gambian village. Resistance of local vectors to pyrethroids and DDT was high (31% and 46% mortality, respectively) while resistance to bendiocarb and pirimiphos methyl was low (88% and 100% mortality, respectively). The vectors were predominantly Anopheles gambiae s.s. with 94% of them having the putative resistant genotype kdr 1014F. Four groups of eight residential compounds were each sprayed with either (1) bendiocarb, a carbamate, (2) DDT, an organochlorine, (3) microencapsulated pirimiphos methyl, an organophosphate, or (4) left unsprayed. All insecticides tested showed high residual activity up to five months after application. Mosquito house entry, estimated by light traps, was similar in all houses with metal roofs, but was significantly less in IRS houses with thatched roofs (p=0.02). Residents participating in focus group discussions indicated that IRS was considered a necessary nuisance and also may decrease the use of long-lasting insecticidal nets. Bendiocarb and microencapsulated pirimiphos methyl are viable alternatives for indoor residual spraying where resistance to pyrethroids and DDT is high and may assist in the management of pyrethroid resistance.

Seasonal use of red-cockaded woodpecker cavities by southern flying squirrels.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loeb, Susan C; Ruth, Deanna L

2004-12-31

Loeb, Susan C., and Deanna L. Ruth. 2004. Seasonal use of red-cockaded woodpecker cavities by southern flying squirrels. In: Red-cockaded woodpecker; Road to Recovery. Proceedings of the 4th Red-cockaded woodpecker Symposium. Ralph Costa and Susan J. Daniels, eds. Savannah, Georgia. January, 2003. Chapter 8. Cavities, Cavity Trees, and Cavity Communities. Pp 501-502. Abstract: Southern flying squirrels can significantly impact red-cockaded woodpecker reproductive success (Laves and Loeb 1999). Thus exclusion or removal of flying squirrels from red-cockaded woodpecker cavities and clusters may be warranted in small woodpecker populations (U.S. Fish and Wildlife Service 2003). However, development of effective and efficient protocolsmore » for southern flying squirrel control requires an understanding of the seasonal dynamics of southern flying squirrel cavity use. Most studies of southern flying squirrel use of red-cockaded woodpecker cavities have been conducted during spring (e.g., Harlow and Lennartz 1983, Rudolph et al. 1990a, Loeb 1993) and no studies have examined the effects of long term flying squirrel control on subsequent cavity use. The objectives of this study were to determine: (1) whether flying squirrel use of red-cockaded woodpecker cavities varies with season or cavity type, and (2) the long term effect of continuous squirrel removal.« less

Characterization of C-ring component assembly in flagellar motors from amino acid coevolution

PubMed Central

dos Santos, Ricardo Nascimento; Khan, Shahid

2018-01-01

Bacterial flagellar motility, an important virulence factor, is energized by a rotary motor localized within the flagellar basal body. The rotor module consists of a large framework (the C-ring), composed of the FliG, FliM and FliN proteins. FliN and FliM contacts the FliG torque ring to control the direction of flagellar rotation. We report that structure-based models constrained only by residue coevolution can recover the binding interface of atomic X-ray dimer complexes with remarkable accuracy (approx. 1 Å RMSD). We propose a model for FliM–FliN heterodimerization, which agrees accurately with homologous interfaces as well as in situ cross-linking experiments, and hence supports a proposed architecture for the lower portion of the C-ring. Furthermore, this approach allowed the identification of two discrete and interchangeable homodimerization interfaces between FliM middle domains that agree with experimental measurements and might be associated with C-ring directional switching dynamics triggered upon binding of CheY signal protein. Our findings provide structural details of complex formation at the C-ring that have been difficult to obtain with previous methodologies and clarify the architectural principle that underpins the ultra-sensitive allostery exhibited by this ring assembly that controls the clockwise or counterclockwise rotation of flagella. PMID:29892378

Experimental Studies of Spray Deposition on a Flat Surface in a Vacuum Environment

NASA Technical Reports Server (NTRS)

Golliher, Eric L.; Yao, S. C.

2015-01-01

Cooling of spacecraft components in the space environment is an on-going research effort. The electronics used in modern spacecraft are always changing and the heat flux is increasing. New, one-of-a-kind missions require new approaches to thermal control. In this research, under vacuum conditions, a pulsed water spray impinged on a small disc, while a high speed data acquisition system recorded the temperature histories of this copper disc. The water droplets froze quickly and accumulated on the disc as the spray continued. After the spray stopped, the frozen water that remained on the disc then sublimated into the vacuum environment and cooled the disc. This paper examines two important aspects of this process: 1) the difference in spray start up and shutdown in a vacuum environment versus in a standard atmospheric pressure environment, and 2) the water utilization efficiency in a vacuum environment due to the effects of drop trajectories and drop bouncing on the surface. Both phenomena play a role during spray cooling in a vacuum. This knowledge should help spacecraft designers plan for spray cooling as an option to cool spacecraft electronics, human metabolic generated heat, and heat from other sources.

Development of a plasma sprayed ceramic gas path seal for high pressure turbine application

NASA Technical Reports Server (NTRS)

Shiembob, L. T.

1978-01-01

Development of the plasma sprayed graded, layered ZRO2/CoCrAlY seal system for gas turbine engine blade tip seal applications up to 1589 K (2400 F) surface temperature was continued. The effect of changing ZRO2/CoCrAlY ratios in the intermediate layers on thermal stresses was evaluated analytically with the goal of identifying the materials combinations which would minimize thermal stresses in the seal system. Three methods of inducing compressive residual stresses in the sprayed seal materials to offset tensile thermal stresses were analyzed. The most promising method, thermal prestraining, was selected based upon potential, feasibility and complexity considerations. The plasma spray equipment was modified to heat, control and monitor the substrate temperature during spraying. Specimens were fabricated and experimentally evaluated to: (1) substantiate the capability of the thermal prestrain method to develop compressive residual stresses in the sprayed structure and (2) define the effect of spraying on a heated substate on abradability, erosion and thermal shock characteristics of the seal system. Thermal stress analysis, including residual stresses and material properties variations, was performed and correlated with thermal shock test results. Seal system performance was assessed and recommendations for further development were made.

Reported community-level indoor residual spray coverage from two-stage cluster surveys in sub-Saharan Africa.

PubMed

Larsen, David A; Borrill, Lauren; Patel, Ryan; Fregosi, Lauren

2017-06-13

Malaria is an important cause of morbidity and mortality in malaria-endemic areas. Indoor residual spray is an effective intervention to control malaria, but high community-level coverage is needed to maximize its impact. Using thirty-four two-stage cluster surveys (e.g., demographic and health surveys) and lot quality assurance sampling, indoor residual spray was estimated at the community level (i.e. enumeration-area) across sub-Saharan Africa since 2010. For communities receiving indoor residual spray a logistic regression predicted whether community-level coverage exceeded 50% or not. Household-level coverage was equitable both in terms of wealth and urban/rural, with poorer and rural houses more likely to be sprayed than richer and urban houses. Coverage of indoor residual spray at the community level is poor across the continent, with 54% of communities receiving the intervention not reaching 50% coverage. Having >50% coverage at the community-level was not associated with increasing the number of houses sprayed in the country. Implementation and monitoring of indoor residual coverage at small geographical scales need to improve greatly to receive maximum benefit of the intervention.

Field Evaluation of a Push-Pull System to Reduce Malaria Transmission

PubMed Central

Menger, David J.; Omusula, Philemon; Holdinga, Maarten; Homan, Tobias; Carreira, Ana S.; Vandendaele, Patrice; Derycke, Jean-Luc; Mweresa, Collins K.; Mukabana, Wolfgang Richard; van Loon, Joop J. A.; Takken, Willem

2015-01-01

Malaria continues to place a disease burden on millions of people throughout the tropics, especially in sub-Saharan Africa. Although efforts to control mosquito populations and reduce human-vector contact, such as long-lasting insecticidal nets and indoor residual spraying, have led to significant decreases in malaria incidence, further progress is now threatened by the widespread development of physiological and behavioural insecticide-resistance as well as changes in the composition of vector populations. A mosquito-directed push-pull system based on the simultaneous use of attractive and repellent volatiles offers a complementary tool to existing vector-control methods. In this study, the combination of a trap baited with a five-compound attractant and a strip of net-fabric impregnated with micro-encapsulated repellent and placed in the eaves of houses, was tested in a malaria-endemic village in western Kenya. Using the repellent delta-undecalactone, mosquito house entry was reduced by more than 50%, while the traps caught high numbers of outdoor flying mosquitoes. Model simulations predict that, assuming area-wide coverage, the addition of such a push-pull system to existing prevention efforts will result in up to 20-fold reductions in the entomological inoculation rate. Reductions of such magnitude are also predicted when mosquitoes exhibit a high resistance against insecticides. We conclude that a push-pull system based on non-toxic volatiles provides an important addition to existing strategies for malaria prevention. PMID:25923114

Deltamethrin resistance in Aedes aegypti results in treatment failure in Merida, Mexico.

PubMed

Vazquez-Prokopec, Gonzalo M; Medina-Barreiro, Anuar; Che-Mendoza, Azael; Dzul-Manzanilla, Felipe; Correa-Morales, Fabian; Guillermo-May, Guillermo; Bibiano-Marín, Wilbert; Uc-Puc, Valentín; Geded-Moreno, Eduardo; Vadillo-Sánchez, José; Palacio-Vargas, Jorge; Ritchie, Scott A; Lenhart, Audrey; Manrique-Saide, Pablo

2017-06-01

The operational impact of deltamethrin resistance on the efficacy of indoor insecticide applications to control Aedes aegypti was evaluated in Merida, Mexico. A randomized controlled trial quantified the efficacy of indoor residual spraying (IRS) against adult Ae. aegypti in houses treated with either deltamethrin (to which local Ae. aegypti expressed a high degree of resistance) or bendiocarb (to which local Ae. aegypti were fully susceptible) as compared to untreated control houses. All adult Ae. aegypti infestation indices during 3 months post-spraying were significantly lower in houses treated with bendiocarb compared to untreated houses (odds ratio <0.75; incidence rate ratio < 0.65) whereas no statistically significant difference was detected between the untreated and the deltamethrin-treated houses. On average, bendiocarb spraying reduced Ae. aegypti abundance by 60% during a 3-month period. Results demonstrate that vector control efficacy can be significantly compromised when the insecticide resistance status of Ae. aegypti populations is not taken into consideration.

Toxicity of Cúspide 480SL® spray mixture formulation of glyphosate to aquatic organisms.

PubMed

Currie, Zachary; Prosser, Ryan S; Rodriguez-Gil, Jose Luis; Mahon, Kim; Poirier, Dave; Solomon, Keith R

2015-05-01

In 2011, an alternative formulation of glyphosate (Cúspide 480SL®) was chosen to replace Roundup-SL®, Fuete-SL®, and Gly-41® for the control of Erythroxylum coca, the source of cocaine, in Colombia. Cúspide 480SL contains the active ingredient glyphosate isopropylamine (IPA) salt, which is the same active ingredient used in previous formulations. However, Cúspide 480SL contains an alkyl polyglycoside surfactant rather than the polyethoxylated tallow amine (POEA) surfactant used in other formulations and known to be more toxic to nonprimary producing aquatic organisms than glyphosate itself. An adjuvant, Cosmo-Flux F411, and water also are added to the spray mixture before application. Aquatic ecosystems adjacent to the target coca fields might be exposed to the spray mix, placing aquatic organisms at risk. Because no toxicity data were available for spray mixture on aquatic organisms, acute toxicity tests were conducted on aquatic plants, invertebrates, and fish, by using the Cúspide 480SL spray mix as described on the label. Based on the median effective concentration (EC50) values for similar organisms, the spray mixture was less toxic to aquatic organisms than formulations previously used for the control of coca (i.e., Roundup-SL, Fuete-SL, and Gly-41). A physical effect induced by Cosmo-Flux F411 was observed in Daphnia magna, Ceriodaphnia dubia, and Hyalella azteca, causing the invertebrates to be trapped in an oily film that was present at the surface of the water. However, a hazard assessment for the Cúspide 480SL spray mix, using estimated worst-case exposure scenario concentrations and EC50 values from the toxicity tests, indicated de minimis hazard for the tested aquatic animals, with hazard quotients all <1. © 2015 SETAC.

Nonlinear Flying Qualities Criteria for Large-Amplitude Maneuvers

DTIC Science & Technology

1984-12-01

theory which are pertinent to the formation of a nonlinear flying qualities methodology. This report surveys nonlinear system theory and describes...the development of an applied flying qualities methodology based on a canonical system theory and using research in relative controllability...The Nonlinear Flying Qualities (NFQ) for Large-Amplitude Maneuvers Program examined promising techniques from nonlinear analysis and nonlinear system

Advanced control technology and airworthiness flying qualities requirements

NASA Technical Reports Server (NTRS)

Snyder, C. T.

1976-01-01

Flying quality requirements are specified in terms of the complete pilot-airframe-systems loop, the task, and the environment. Results from a study of flying qualities are reported. A review of the treatment of failure cases in various flying quality requirements is presented along with a description of the methods used and relevant lessons learned from recent Autoland certification programs.

Discovery, development, and evaluation of a horn fly-isolated (Diptera: Muscidae) Beauveria bassiana (Hypocreales: Cordyciptaceae) strain from Florida, U.S.A

USDA-ARS?s Scientific Manuscript database

The horn fly is an important cattle pest and traditionally has been managed using insecticides; however, many horn fly populations are insecticide-resistant in the United States. Use of alternative control techniques has been limited because of the challenges of managing a fly pest on pastured cattl...

[Detection of entomopathogen nematode [EPN - sand flies (Phlebotomus tobbi)] caught in the wild in Aydın, Kuşadası town and its assessment as a biological control agent].

PubMed

Karakuş, Mehmet; Arserim, Suha K; Töz, Seray Özensoy; Özbel, Yusuf

2013-01-01

In this study, the midgut of the sand flies investigated with direct method for the presence of parasites and other organisms. Wild sand flies collected in Kuşadası Town-Aydın, were dissected and midgut contents were examined by light microscopy. After midgut dissection, the head and genitalia of sand fly specimens were clarified and mounted for species identification. During the study, a total of 1027 sand flies were dissected. Eight and two species belonging to Phlebotomus and Sergentomyia genera were determined, respectively. Phlebotomus tobbi was found to be most abundant species (61.34%). A third stage of infective Entomopathogen Nematode belonging to Steinernematidae family was observed in the hemocoel of one specimen of P. tobbi during the dissection process. This is the first finding related to entomopathogen nematodes found in sand flies in Turkey. In the study, the sand fly fauna was determined in Kuşadası Town. For the control of sand flies, entomopathogenic nematodes which are not harmful for non-target organisms, can be used instead of chemical insecticides that can cause unknown damage in the environment.

Can Escherichia coli fly? The role of flies as transmitters of E. coli to food in an urban slum in Bangladesh.

PubMed

Lindeberg, Yrja Lisa; Egedal, Karen; Hossain, Zenat Zebin; Phelps, Matthew; Tulsiani, Suhella; Farhana, Israt; Begum, Anowara; Jensen, Peter Kjaer Mackie

2018-01-01

To investigate the transmission of faecal bacteria by flies to food under natural settings. Over a period of 2 months, paired (exposed and non-exposed) containers with cooked rice were placed on the ground in kitchen areas in an urban slum area in Dhaka, Bangladesh, and the numbers of flies landing on the exposed rice were counted. Following exposure, the surface of the rice was microbiologically and molecularly analysed for the presence of Escherichia coli and genes of diarrhoeagenic E. coli and Shigella strains. Rice was at greater risk (P < 0·001) of being contaminated with E. coli if flies landed on the rice than if no flies landed on the rice (odds ratio 5·4 (P < 0·001, 95% CI: 2·5-11·7). Mean contamination in exposed rice samples (n = 60) was 3·1 × 103 CFU/g (95% CI: 2·2 × 103-4·0 × 103). Furthermore, for approximately half of the observed fly landings, the average CFU per fly landing was >0·6 × 103 CFU. Genes of diarrhoeagenic E. coli and Shigella species were detected in 39 of 60 (65%) of exposed rice samples. Two fly species were identified: the common housefly (Musca domestica) and the oriental latrine fly (Chrysomya megacephala). Flies may transmit large quantities of E. coli to food under field settings. The findings highlight the importance of implementing control measures to minimise exposure of food to flies to ensure food safety. Fly control measures should be considered for the prevention of diarrhoeal diseases caused by E. coli. © 2017 John Wiley & Sons Ltd.

Purple Phototrophic Bacterium Enhances Stevioside Yield by Stevia rebaudiana Bertoni via Foliar Spray and Rhizosphere Irrigation

PubMed Central

Wu, Jing; Wang, Yiming; Lin, Xiangui

2013-01-01

This study was conducted to compare the effects of foliar spray and rhizosphere irrigation with purple phototrophic bacteria (PPB) on growth and stevioside (ST) yield of Stevia. rebaudiana. The S. rebaudiana plants were treated by foliar spray, rhizosphere irrigation, and spray plus irrigation with PPB for 10 days, respectively. All treatments enhanced growth of S. rebaudiana, and the foliar method was more efficient than irrigation. Spraying combined with irrigation increased the ST yield plant -1 by 69.2% as compared to the control. The soil dehydrogenase activity, S. rebaudiana shoot biomass, chlorophyll content in new leaves, and soluble sugar in old leaves were affected significantly by S+I treatment, too. The PPB probably works in the rhizosphere by activating the metabolic activity of soil bacteria, and on leaves by excreting phytohormones or enhancing the activity of phyllosphere microorganisms. PMID:23825677

Effect of pH of spray solution on the electrical properties of cadmium oxide thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hodlur, R. M.; Gunnagol, Raghu M.; Rabinal, M. K., E-mail: mkrabinal@yahoo.com

2015-06-24

Highly conducting transparent cadmium oxide thin films were prepared by conventional spray pyrolysis technique on glass at 375 °C substrate temperature. The pH of the spray solution was varied by adding ammonia/hydrochloric acid in the spray solution. The XRD pattern showed cubic phase. A lowest resistivity of 9.9 × 10{sup −4} Ω cm (with carrier concentration (n) = 5.1 × 10{sup 20} cm{sup −3}, mobility (µ)=12.4 cm{sup 2}/Vs) is observed for pH ∼12. The resistivity is tuned almost by three orders of magnitude by controlling the bath pH with optical transmittance more than 70 %. Thus, without any doping, the electricalmore » conductivity of CdO films could be easily tuned by simply varying the pH of spray solution without compromising the transparency and keeping the other deposition parameters fixed.« less

Detailed investigation of a vaporising fuel spray. Part 1: Experimental investigation of time averaged spray

NASA Technical Reports Server (NTRS)

Yule, A. J.; Seng, C. A.; Boulderstone, R.; Ungut, A.; Felton, P. G.; Chigier, N. A.

1980-01-01

A laser tomographic light scattering technique provides rapid and accurate high resolution measurements of droplet sizes, concentrations, and vaporization. Measurements using a computer interfaced thermocouple are presented and it is found that the potential exists for separating gas and liquid temperature measurements and diagnosing local spray density by in situ analysis of the response characteristics of the thermocouple. The thermocouple technique provides a convenient means for measuring mean gas velocity in both hot and cold two phase flows. The experimental spray is axisymmetric and has carefully controlled initial and boundary conditions. The flow is designed to give relatively insignificant transfer of momentum and mass from spray to air flow. The effects of (1) size-dependent droplet dispersion by the turbulence, (2) the initial spatial segregation of droplet sizes during atomization, and (3) the interaction between droplets and coherent large eddies are diagnosed.

Modeling Droplet Heat and Mass Transfer during Spray Bar Pressure Control of the Multipurpose Hydrogen Test Bed (MHTB) Tank in Normal Gravity

NASA Technical Reports Server (NTRS)

Kartuzova, O.; Kassemi, M.

2016-01-01

A CFD model for simulating pressure control in cryogenic storage tanks through the injection of a subcooled liquid into the ullage is presented and applied to the 1g MHTB spray bar cooling experiments. An Eulerian-Lagrangian approach is utilized to track the spray droplets and capture the interaction between the discrete droplets and the continuous ullage phase. The spray model is coupled with the VOF model by performing particle tracking in the ullage, removing particles from the ullage when they reach the interface, and then adding their contributions to the liquid. A new model for calculating the droplet-ullage heat and mass transfer is developed. In this model, a droplet is allowed to warm up to the saturation temperature corresponding to the ullage vapor pressure, after which it evaporates while remaining at the saturation temperature. The droplet model is validated against the results of the MHTB spray-bar cooling experiments with 50% and 90% tank fill ratios. The predictions of the present T-sat based model are compared with those of a previously developed kinetic-based droplet mass transfer model. The predictions of the two models regarding the evolving tank pressure and temperature distributions, as well as the droplets' trajectories and temperatures, are examined and compared in detail. Finally, the ullage pressure and local vapor and liquid temperature evolutions are validated against the corresponding data provided by the MHTB spray bar mixing experiment.

Semiochemical-based technologies for fly management

USDA-ARS?s Scientific Manuscript database

Filth flies are important insect pests that have caused over billions of dollars damage in animal production, food contamination and disease transmitting. The present presentation reports our recent findings on the development of filth fly control using semiochemical-based technologies to reduce the...

Testing for Mutagens Using Fruit Flies.

ERIC Educational Resources Information Center

Liebl, Eric C.

1998-01-01

Describes a laboratory employed in undergraduate teaching that uses fruit flies to test student-selected compounds for their ability to cause mutations. Requires no prior experience with fruit flies, incorporates a student design component, and employs both rigorous controls and statistical analyses. (DDR)

Effectiveness of salicylic acid paste for treatment of digital dermatitis in dairy cows compared with tetracycline spray and hydrotherapy.

PubMed

Kofler, Johann; Innerebner, Carmen; Pesenhofer, Robert; Hangl, Andreas; Tichy, Alexander

2015-01-01

The effectiveness of salicylic acid paste (PASTE) was tested for topical treatment of 25 acute and 25 chronic digital dermatitis (DD) lesions. Control groups with the same number of acute and chronic DD lesions were treated with topical oxytetracycline spray (SPRAY) and by washing only with water (HYDRO) respectively. The therapeutic effects were evaluated using a pain score, the healing rate, the lesion size and other parameters. Pre-treatment and control examinations were carried out on day 0, 4, 14 and 21. In the PASTE group, 76.0% of acute DD lesions were pain free and 64.0% of acute DD lesions were healed on day 21 showing a normal skin surface (MO). Only 28.0% of acute DD lesions treated with SPRAY and 16.0% treated with HYDRO had healed on day 21. A significantly higher healing rate was revealed in acute lesions for the PASTE compared to the HYDRO group (p < 0.05) for all three re-checks, and for the PASTE group compared with the SPRAY group (p < 0.05) for day 4 and day 14. Healing rates of chronic DD lesions were higher in the PASTE group with 44.0% on day 14 and 36.0% on day 21, compared with 16.0% in the SPRAY and 32.0% in the HYDRO group on day 14, and 20.0% (SPRAY) and 28.0% (HYDRO) on day 21 respectively. The recurrence rate of lesions after they had healed during the study period was 14.5% in total. Digital dermatitis lesions treated with salicylic acid paste and a wrap showed significantly higher healing rates within the study period, odds ratios for healing of acute lesions with PASTE were 4.5 to 6.7 times higher than with SPRAY, and 9.3 to 36.4 higher compared with HYDRO.

Differences in Cutaneous Irritation of Five Commonly Used Topical Products.

PubMed

Draelos, Zoe Diana

2016-07-01

Irritation, such as burning and stinging, on the site of application, is a common side effect of topical dermatologic products including creams, lotions, sprays, and foams. This effect may be more pronounced when applying products to atopic or psoriatic skin. The composition of the vehicle may affect the extent of the irritation. This study compared the irritation and erythema potential of 7 different topical dermatologic products to determine the products with the least likelihood of causing discomfort when applied.
Seven sites on the anterior leg of 30 subjects were dry shaven with 10 upward strokes. Subjects rated the stinging of petrolatum (negative control), isopropyl alcohol (positive control), Cetaphil Lotion, triamcinolone 0.1% cream, triamcinolone 0.2% spray, betamethasone foam, and clobetasol 0.05% spray, 1 minute after product application, using a scale of 0 (no symptoms) to 10 (intolerable stinging/burning). The investigator assessed erythema at the sites 30 minutes after application of the products using a scale of 0 (none) to 4 (severe).
Stinging rating score of each product was statistically significant from one another. Petrolatum produced the least stinging (0) and isopropyl alcohol the most (10). Stinging with triamcinolone spray, Cetaphil Lotion, and triamcinolone cream ranked in the lower half of the rating scale (all below 5). Betamethasone foam and clobetal spray ranked the highest at >7. When corrected for the erythema caused by shaving, triamcinolone spray and Cetaphil Lotion produced the least amount of erythema of all the products tested.
Rapid evaporation of the volatile vehicle of triamcinolone spray and the non-irriating nature of the medication left behind may contribute to its low erythema and stinging. This product may be an appropriate choice for patients with compromised skin but who require the advantages and conveniences of a spray vehicle.

J Drugs Dermatol. 2016;15(7):870-873.

Formation Flying in Earth, Libration, and Distant Retrograde Orbits

NASA Technical Reports Server (NTRS)

Folta, David C.

2004-01-01

This slide presentation examines the current and future state of formation flying, LEO formations, control strategies for flight in the vicinity of the libration points, and distant retrograde orbit formations. This discussion of LEO formations includes background on perturbation theory/accelerations and LEO formation flying. The discussion of strategies for formation flight in the vicinity of the libration points includes libration missions and natural and controlled libration orbit formations. A reference list is included.

Enhanced Formation Flying for the Earth Observing-1 (EO-1) New Millennium Mission

NASA Technical Reports Server (NTRS)

Folta, David; Quinn, David

1997-01-01

With scientific objectives for Earth observation programs becoming more ambitious and spacecraft becoming more autonomous, the need for new technical approaches on the feasibility of achieving and maintaining formations of spacecraft has come to the forefront. The trend to develop small low cost spacecraft has led many scientists to recognize the advantage of flying several spacecraft in formation, an example of which is shown in the figure below, to achieve the correlated instrument measurements formerly possible only by flying many instruments on a single large platform. Yet, formation flying imposes additional complications on orbit maintenance, especially when each spacecraft has its own orbit requirements. However, advances in automation proposed by GSFC Codes 550 and 712 allow more of the burden in maneuver planning and execution to be placed onboard the spacecraft, mitigating some of the associated operational concerns. The purpose of this analysis is to develop the fundamentals of formation flying mechanics, concepts for understanding the relative motion of free flying spacecraft, and an operational control theory for formation maintenance of the Earth Observing-1 (EO-l) spacecraft that is part of the New Millennium. Results of this development can be used to determine the appropriateness of formation flying for a particular case as well as the operational impacts. Applications to the Mission to Planet Earth (MTPE) Earth Observing System (EOS) and New Millennium (NM) were highly considered in analysis and applications. This paper presents the proposed methods for the guidance and control of the EO-1 spacecraft to formation fly with the Landsat-7 spacecraft using an autonomous closed loop three axis navigation control, GPS, and Cross link navigation support. Simulation results using various fidelity levels of modeling, algorithms developed and implemented in MATLAB, and autonomous 'fuzzy logic' control using AutoCon will be presented. The results of these analysis on the ability to meet mission and formation flying requirements will be presented.