DOE Office of Scientific and Technical Information (OSTI.GOV)
Not Available
1993-12-31
The primary goal of this project is the characterization of the low NO{sub x} combustion equipment through the collection and analysis of long-term emissions data. A target of achieving fifty percent NO{sub x} reduction using combustion modifications has been established for the project. The project provides a stepwise retrofit of an advanced overfire air (AOFA) system followed by low NO{sub x} burners (LNB). During each test phase of the project, diagnostic, performance, long-term and verification testing will be performed. These tests are used to quantify the NO{sub x} reductions of each technology and evaluate the effects of those reductions onmore » other combustion parameters such as particulate characteristics and boiler efficiency. Baseline, AOFA, and LNB without AOFA test segments have been completed. Analysis of the 94 days of LNB long-term data collected show the full-load NO{sub x} emission levels to be approximately 0.65 lb/MBtu with flyash LOI values of approximately 8 percent. Corresponding values for the AOFA configuration are 0.94 lb/MBtu and approximately 10 percent. For comparison, the long-term full-load, baseline NO{sub x} emission level was approximately 1.24 lb/MBtu at 5.2 percent LOI. Comprehensive testing of the LNB plus AOFA configuration began in May 1993 and is scheduled to end during August 1993. As of June 30, the diagnostic, performance, chemical emissions tests segments for this configuration have been conducted and 29 days of long-term, emissions data collected. Preliminary results from the May--June 1993 tests of the LNB plus AOFA system show that the full load NO{sub x} emissions are approximately 0.42 lb/MBtu with corresponding fly ash LOI values near 8 percent. This is a substantial improvement in both NO{sub x} emissions and LOI values when compared to the results obtained during the February--March 1992 abbreviated testing of this system.« less
Kurella, Swamy; Meikap, Bhim Charan
2016-08-23
In this work, fly-ash water scrubbing experiments were conducted in a three-stage lab-scale dual-flow sieve plate scrubber to observe the performance of scrubber in fly-ash removal at different operating conditions by varying the liquid rate, gas rate and inlet fly-ash loading. The percentage of fly-ash removal efficiency increases with increase in inlet fly-ash loading, gas flow rate and liquid flow rate, and height of the scrubber; 98.55% maximum percentage of fly-ash removal efficiency (ηFA) is achieved at 19.36 × 10(-4) Nm(3)/s gas flow rate (QG) and 48.183 × 10(-6) m(3)/s liquid flow rate (QL) at 25 × 10(-3) kg/Nm(3) inlet fly-ash loading (CFA,i). A model has also been developed for the prediction of fly-ash removal efficiency of the column using the experimental results. The predicted values calculated using the correlation matched well with the experimental results. Deviations observed between the experimental and the predicted values were less than 20%.
Effect of the raw material composition of fabrics on the Limiting Oxygen Index (LOI)
NASA Technical Reports Server (NTRS)
Jeler, S.; Ceric, B.
1986-01-01
The raw material composition of fabrics is one of the most important factors for LOI value. LOI value was determined in samples of varying composition composed of cellulose, protein, and synthetic fibers and their mixtures, based on ASTM D 2863-76. Cellulose fibers and their mixtures exhibited the lowest value, while synthetic fibers had the highest LOI value.
Flyash in continuous reinforced PCC pavement and lean concrete base : interim report.
DOT National Transportation Integrated Search
1986-08-01
The objectives of this test section were: 1) To test and evaluate the physical characteristics of flyash concrete in comparison to non-flyash concrete. Tests will be conducted to see if flyash strength, and if the current specifications for flyash ca...
NASA Astrophysics Data System (ADS)
Weber, Jerzy; Jerzykiewicz, Maria; Jamroz, Elżbieta; Kocowicz, Andrzej; Dębicka, Magdalena; Ćwieląg-Piasecka, Irmina
2017-04-01
Literature on fly-ash influence on the environment report mainly on alkalization effect on vegetation and changes in chemistry of forest floor. As far as now soils were examined only for changes in pH in surface horizons, physical properties and heavy metal solubility. Soil properties strongly depend on soil organic matter content and humic substances properties, thus their modification plays a crucial role in soil forming processes and changes in the environment. From the other side, the alkalization effects on podzolization processes and particularly on humic substances have not been recognized. The aim of this paper was to characterize changes in properties of humic substances in ectohumus horizons of Podzols affected by alkali blown out from fly-ash dumping site of power station Bełchatów, central Poland. The objects of the investigation were Podzols derived from loose quartz sand, developed under pine forest. They surround the dumping site, which was established to store wastes from lignite combustion in Bełchatów power station. The samples were collected from ectohumus horizons in direct vicinity of the dumping site (50 m) as well as in the control area (7.3 km away) in five replications. Determination of elemental composition and spectroscopic analysis (EPR, FT-IR, ICP-OES and UV-Vis) were performed for humic acids, fulvic acids and humines extracted with standard IHSS procedure. An increase of pH in ectohumus horizons caused by the influence of fly-ash leads to change in humic substances structure. Obtained results showed that humic and fulvic acids from fly-ash affected Podzols indicated higher contents of nitrogen and sulphur, as well as higher O/C and lower C/N ratios. This points out a higher degree of their humification. Also EPR analyses of humic acids and humins affected by fly-ash indicated higher metal ions concentrations. However, the increase of Mn and Fe ions concentration did not affect the Fe(III) and Mn(II) band intensities of EPR spectra. This may suggest the presence of other forms (other oxidation state) of Mn and Fe ions, that are diamagnetic and hence EPR silent. Lower g-factors values of radicals built-in humic substances extracted from fly-ash affected soils are associated with more condensed structures with lower content of oxygen functional groups. Decrease of free radicals concentration in Podzols affected by fly-ash is correlated with an increase of the transition metal ions, such as Mn(II) and Fe(III), which interact (antiferromagnetically) with semiquinone radicals built-in humic substances macromolecules. Humic acids from fly-ash affected site indicated lower values of E4/E6 ratio, which confirmed higher molecular weight of the molecules. Thus the humic fractions from ectohumus horizon of the fly-ash affected area could be described as having heavier, more complex structure then those from control area. Above mentioned modification of humic substances may contribute to restriction of the podzolization processes, and transformation of underlying eluvial horizons into transitional AE horizons. Furthermore, due to transformation and translocation of organic components, illuvial Bhs horizons can be transformed into Bs horizons.
Water Use in Wetland Kalo Cultivation in Hawai`i
Gingerich, Stephen B.; Yeung, Chiu W.; Ibarra, Tracy-Joy N.; Engott, John A.
2007-01-01
Ten cultivation areas (8 windward, 2 leeward) were selected for a kalo water-use study, primarily on the basis of the diversity of environmental and agricultural conditions under which wetland kalo is grown and landowner permission and availability. Flow and water-temperature data were collected at the lo`i complex level and at the individual lo`i level. To ensure that flow and temperature data collected at different lo`i reflect similar irrigation conditions (continuous flooding of the mature crop), only lo`i with crops near the harvesting stage were selected for water-temperature data collection. The water need for kalo cultivation varies depending on the crop stage. In this study, data were collected during the dry season (June-October), when water requirements for cooling kalo approach upper limits. Flow measurements generally were made during the warmest part of the day, and temperature measurements were made every 15 minutes at each site for about a two-month period. Flow and temperature data were collected from kalo cultivation areas on four islands - Kaua`i, O`ahu, Maui, and Hawai`i. The average inflow value for the 19 lo`i complexes measured in this study is 260,000 gallons per acre per day, and the median inflow value is 150,000 gallons per acre per day. The average inflow value for the 17 windward sites is 270,000 gallons per acre per day, and the median inflow value is 150,000 gallons per acre per day. The average inflow value for the two leeward sites is 150,000 gallons per acre per day. The average inflow value measured for six individual lo`i is 350,000 gallons per acre per day, and the median inflow value is 270,000 gallons per acre per day. The average inflow value for the five windward lo`i is 370,000 gallons per acre per day, and the median inflow value is 320,000 gallons per acre per day. The inflow value for the one leeward lo`i is 210,000 gallons per acre per day. These inflow values are consistent with previously reported values for inflow and are significantly higher than values generally estimated for water consumption during kalo cultivation. These measurements of inflow are important for future considerations of water-use requirements for successful kalo cultivation. Of the 17 lo`i complexes where water inflow temperature was measured, only 3 had inflow temperatures that rose above 27 ?C, the threshold temperature above which wetland kalo is more susceptible to fungi and associated rotting diseases. The coldest mean inflow temperature was 20.0 ?C and the warmest inflow temperature was 24.9 ?C. All 15 of the sites where outflow temperatures were measured had some temperatures greater than 27 ?C. Outflow temperatures exceeded 27 ?C between 2.5 percent and about 40 percent of the time. Mean outflow temperatures ranged from 23.0 ?C to 26.7 ?C.
DOT National Transportation Integrated Search
1991-07-01
Proposed research on this project included five main objectives: 1) To test and evaluate the physical characteristics of flyash concrete in comparions to non-flyash concrete. Tests will be conducted to see if flyash concrete meets OSHD specifications...
Onwudili, Jude A; Hajizadeh, Yaghoub; Zainal, Safari; Upton, John; Williams, Paul T
2011-12-15
The seventeen 2378-substituted polychlorinated dibenzo-p-dioxins and dibenzo-p-furans (PCDD/Fs) congeners have been separated and analyzed in sewage sludge and incinerator flyash samples using a CP-Sil 88 column (50 m × 0.25 mm I.D., 0.25 μm film thickness) operating at a maximum oven temperature of 240°C. The column was used on a Varian 450-GC with a Varian 320-MS Triple Quadrupole. Calibration standards were used to determine the transition chemistries of the 2378-substituted PCDD/F congeners in the gas chromatography/mass spectrometry (GC-MS/MS) system. The five-point calibration curve for each of the congeners showed very good linearity with R(2) values greater than 0.999. The recovery of labelled compounds ranged from 50% to 120%. Analytical results from a reference flyash (BCR-490) and a reference sewage sludge (BCR-677) compared very well with the certified values, giving percentage deviations in I-TEQ (international toxic equivalents) of 4.93% and 0.53%, respectively. Results from 'real' flyash samples underscored the level of progress made in the abatement of dioxin emissions from incinerators; the old incinerator flyash contained much higher PCDD/F concentrations than the modern one. In addition, the concentrations profiles of PCDD/Fs in the 'real' sewage sludge from two UK wastewater treatment plants (WWTPs) showed that one contained a total PCDD/Fs content of 314 ng I-TEQ kg(-1), while the other gave a total of 53 ng I-TEQ kg(-1). Over an 18-month period of operation, no significant loss of analytical performance was observed from the low-temperature column. Copyright © 2011 Elsevier B.V. All rights reserved.
More and more power plant flyash is being recycled
DOE Office of Scientific and Technical Information (OSTI.GOV)
Golden, D.; Sauber, R.
A number of viable options have been demonstrated for recycling flyash, one of America's fastest-growing waste products. Application opportunities range from structural fills to pavement bases, concrete, stabilizing backfills, and a metal-castings alloy. But two stumbling blocks still face utilities and marketers of flyash. They are: (1) Convincing potential end users that flyash is a beneficial raw material and not an inferior waste product. (2) Persuading regulatory agencies to draft legislation, that promote, if not mandate, its use.
The geochemistry and bioreactivity of fly-ash from coal-burning power stations.
Jones, Timothy; Wlodarczyk, Anna; Koshy, Lata; Brown, Patrick; Shao, Longyi; BéruBé, Kelly
2009-07-01
Fly-ash is a byproduct of the combustion of coal in power stations for the generation of electricity. The fly-ash forms from the melting of incombustible minerals found naturally in the coal. The very high coal combustion temperatures result in the formation of microscopic glass particles from which minerals such as quartz, haematite and mullite can later recrystallize. In addition to these minerals, the glassy fly-ash contains a number of leachable metals. Mullite is a well-known material in the ceramics industry and a known respiratory hazard. Macroscopically mullite can be found in a large range of morphologies; however microscopic crystals appear to favour a fibrous habit. Fly-ash is a recognized bioreactive material in rat lung, generating hydroxyl radicals, releasing iron, and causing DNA damage. However, the mechanisms of the bioreactivity are still unclear and the relative contributions of the minerals and leachable metals to that toxicity are not well known.
NASA Astrophysics Data System (ADS)
Huo, Pengwei; Yan, Yongsheng; Li, Songtian; Li, Huaming; Huang, Weihong
2010-03-01
A series of poly-o-phenylenediamine/TiO 2/fly-ash cenospheres(POPD/TiO 2/fly-ash cenospheres) composites have been prepared from o-phenylenediamine and TiO 2/fly-ash cenospheres under various polymerization conditions. The properties of the samples were characterized by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), specific surface area (BET), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) and UV-vis diffuse reflectance spectrum (UV-vis DRS). Photocatalytic activity was studied by degradation of antibiotics waste water under visible light. The results indicate that the photo-induced method is viable for preparing modified photocatalysts, and the modified photocatalysts have good absorption in visible light range. The photocatalysts of POPD/TiO 2/fly-ash cenospheres which have good performance are prepared at pH 3 and 4, and the polymerized time around 40 min. When the photocatalysts are prepared under the conditions of pH 3 and polymerized time 40 min, the degradation rate of roxithromycin waste water could reach near 60%, and it indicates that the way of POPD modified TiO 2/fly-ash cenospheres to degrade the antibiotics waste water is viable.
NASA Astrophysics Data System (ADS)
Kapicka, Ales; Kodesova, Radka; Petrovsky, Eduard; Grison, Hana
2010-05-01
Several studies confirm that soil magnetometry can serve as proxy of industrial immisions as well as heavy-metal contamination. The important assumption for magnetic mapping of contaminated soils is that atmospherically deposited particulate matter, including the ferrimagnetic phase, accumulates in the top soil horizons and remains there over long period. Only if this is true, large areas can be reliably mapped using soil magnetometry, and, moreover, this method can be used also for long-term monitoring. However, in soil types such as sandy soils with different porosity or soils with substantial variability of water regime, translocation of the deposited anthropogenic particles may result in biased (underestimated) values of the measured topsoil magnetic susceptibility. From the physical point of view, this process may be considered as colloid transport through porous medium. In our column experiments in laboratory we used three technical sands with different particle sizes (0,63 - 1.25mm, 0,315-0,80mm, 0,10-0,63mm). Sands in cylinders were contaminated on the surface by fly-ashes from coal-burning power plant (mean grain size 10μm) and fine grained Fe3O4 (grain size < 20 μm). Soil moisture sensors were used to monitor water regime within the sand columns after controlled rain simulation and temperature distribution in sand column was measured as well. Vertical migration of ferrimagnetic particles-tracers presented in the fly-ash was measured by SM 400 Kappameter. By means of magnetic susceptibility distribution we studied two parameters: gradual shift of peak concentration of contaminants (relative to surface layer) and maximum penetration depth. Results indicated that after rain simulation (pulls infiltration of defined water volume) the positions of peak values moved downwards compared to the initial state and gradual decrease of susceptibility peak values were detected in all studied sand formations. Fly-ash migrated more or less freely in coarse sand material. In medium and fine sand the contaminants moved only to the depths of several cm due to the pore-space blocking and water flow decrease. Fine-grained magnetite shows different behavior. Position of peaks value is more or less stable and maximum depth of penetration is only a few cm in all cases. Higher grain size value is probably reason for higher stability of magnetite. Moreover, magnetic interaction between grains increase "effective" grain size value and restricts transport in material with given porosity. This research is supported by the Grant Agency ASCR under grant IAA300120701
Development and freeze-thaw durability of high flyash-content concrete
DOE Office of Scientific and Technical Information (OSTI.GOV)
Sajadi, J.
1987-01-01
Objectives were to investigate the effects on concrete strength, drying shrinkage, freeze-thaw durability, and air-void system parameters of replacing various amounts of portland cement with different types of fly ash and to compare selected characteristics of such fly-ash concretes and fly-ash concretes containing a high-range water-reducing admixture to those of a control mixture. It was concluded that concrete mixtures with 90-day compressive strengths equal to the control could be produced when large amounts of cement were replaced by fly ash. In addition, when the high-range water-reducing admixtures was employed, very large amounts of cement could be replaced by fly ashmore » to yield mixtures whose compressive strengths were equal to or greater than the strengths of the control mix at all ages. The maximum amount of cement that could be replaced for equal-strength mixtures depended upon the nature of the fly ash. Drying shrinkage of plain fly-ash concretes and fly-ash concretes containing the high-range water-reducing admixture were similar to those of the control mix. The optimum fly-ash content in a concrete is comparable in strength and durability to a conventional (control) concrete was influenced by the chemical and physical characteristics of the fly ash.« less
NASA Astrophysics Data System (ADS)
Revathi, Purushothaman; Nikesh, P.
2018-04-01
In the frame of an extended research programme dealing with the utilization of recycled aggregate in concrete, the corrosion resistance characteristics of rebars embedded in recycled aggregate concrete is studied. Totally five series of concrete mixtures were prepared with fly-ash as replacement for cement in the levels of 10-30% by weight of cement. Corrosion studies by 90 days ponding test, linear polarization test and impressed voltage tests were carried out, in order to investigate whether corrosion behaviour of the rebars has improved due to the replacement of cement with fly-ash. Results showed that the replacement of cement with fly-ash in the range of 20-30% improves the corrosion resistance characteristics of recycled aggregate concrete.
Numerical study of the light output intensity of the bilayer organic light-emitting diodes
NASA Astrophysics Data System (ADS)
Lu, Feiping
2017-02-01
The structure of organic light-emitting diodes (OLEDs) is one of most important issues that influence the light output intensity (LOI) of OLEDs. In this paper, based on a simple but accurate optical model, the influences of hole and electron transport layer thickness on the LOI of bilayer OLEDs, which with N,N0- bis(naphthalen-1-yl)-N,N0- bis(phenyl)- benzidine (NPB) or N,N'- diphenyl-N,N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4-diamine (TPD) as hole transport layer, with tris(8-hydroxyquinoline) aluminum (Alq3) as electron transport and light emitting layers, were investigated. The laws of LOI for OLEDs under different organic layer thickness values were obtained. The results show that the LOI of devices varies in accordance with damped cosine or sine function as the increasing of organic layer thickness, and the results show that the bilayer OLEDs with the structure of Glass/ITO/NPB (55 nm)/Alq3 (75 nm)/Al and Glass/ITO/TPB (60 nm)/Alq3 (75 nm)/Al have most largest LOI. When the thickness of Alq3 is less than 105 nm, the OLEDs with TPD as hole transport layer have larger LOI than that with NPB as hole transport layer. The results obtained in this paper can present an in-depth understanding of the working mechanism of OLEDs and help ones fabricate high efficiency OLEDs.
NASA Astrophysics Data System (ADS)
Singh, Vishwanath P.; Badiger, N. M.; El-Khayatt, A. M.
2014-06-01
We have computed γ-ray exposure buildup factors (EBF) of some building materials; glass, marble, flyash, cement, limestone, brick, plaster of paris (POP) and gypsum for energy 0.015-15 MeV up to 40 mfp (mfp, mean free path) penetration depth. Also, the macroscopic effective removal cross-sections (ΣR) for fast neutron were calculated. We discussed the dependency of EBF values on photon energy, penetration depth and chemical elements. The half-value layer and kinetic energy per unit mass relative to air of building materials were calculated for assessment of shielding effectiveness. Shielding thicknesses for glass, marble, flyash, cement, limestone and gypsum plaster (or Plaster of Paris, POP) were found comparable with ordinary concrete. Among the studied materials limestone and POP showed superior shielding properties for γ-ray and neutron, respectively. Radiation safety inside houses, schools and primary health centers for sheltering and annual dose can be assessed by the determination of shielding parameters of common building materials.
Corbacho, J A; Baeza, A
2018-05-17
The evaluation of the radiological impact in soils due to the fly-ash ponds using both in situ techniques and laboratory based measurements is presented. In order to check the in situ techniques capabilities for monitoring this type of industries, a comparison between both techniques was performed. A characterization of external radiation exposure in the fly-ash pond and in its surrounding soils was made. The associated external radiological hazard due to the fly-ash pond has been evaluated. In situ techniques could be used to determine the radiological impact on soils due to fly-ash deposition, but its use could be limited due to the associated uncertainties.
Use of flyash and biogas slurry for improving wheat yield and physical properties of soil.
Garg, R N; Pathak, H; Das, D K; Tomar, R K
2005-08-01
This study explores the potential use of by-products of energy production, i.e., (i) flyash from coal-powered electricity generation and (ii) biogas slurry from agricultural waste treatment, as nutrient sources in agriculture. These residues are available in large amounts and their disposal is a major concern for the environment. As both residues contain considerable amounts of plant nutrients, their use as soil amendment may offer a promising win-win opportunity to improve crop production and, at the same time, preventing adverse environmental impacts of waste disposal. Effect of flyash and biogas slurry on soil physical properties and growth and yield of wheat (Triticum aestivum) was studied in a field experiment. Leaf area index, root length density and grain yield of wheat were higher in plots amended with flyash or biogas slurry compared to unamended plots. Both types of amendments reduced bulk density, and increased saturated hydraulic conductivity and moisture retention capacity of soil. The study showed that flyash and biogas slurry should be used as soil amendments for obtaining short-term and long-term benefits in terms of production increments and soil amelioration.
ELECTRIC-FIELD-ENHANCED FABRIC FILTRATION OF ELECTRICALLY CHARGED FLYASH
The paper summarizes measurements in which both external electric field (applied by electrodes at the fabric surface) and flyash electrical charge (controlled by an upstream corona precharger) are independent variables in a factorial performance experiment carried out in a labora...
Spray scrubbing of particulate-laden SO(2) using a critical flow atomizer.
Bandyopadhyay, Amitava; Biswas, Manindra Nath
2008-08-01
The performance of a spray tower using an energy efficient two-phase critical flow atomizer on the scrubbing of particulate-laden SO(2) using water and dilute NaOH is reported in this article. Experimentation revealed that SO(2) removal was enhanced due to presence of particles (fly-ash) and almost 100% removal efficiency was achieved in water scrubbing. The removal efficiency is elucidated in reference to atomizing air pressure, droplet diameter and droplet velocity besides other pertinent variables of the system studied. The presence of fly-ash particles improved the removal efficiency to about 20% within the range of variables studied. Empirical and semi-empirical correlations were developed for predicting the removal efficiency in water and dilute NaOH respectively. Predicted data fitted excellently well with experimental values. The performance of the spray tower is compared with the performances of existing systems and very encouraging results are obtained.
Modulation of flyash-induced genotoxicity in Vicia faba by vermicomposting.
Jain, Kavindra; Singh, Jitendra; Chauhan, L K S; Murthy, R C; Gupta, S K
2004-09-01
Cytogenetic effects of pre- and postvermicomposted flyash samples were evaluated on the root meristem cells of Vicia faba. Seedlings of V. faba were directly sown in flyash and cow dung-soil mixtures (20%, 40%, 60%, and 80%) and the lateral roots grown in these test mixtures were sampled at 5 days. Negative control was run parallel in cow dung-soil (CS) mixture alone. One set of flyash-cow dung-soil (FCS) mixture was subjected to vermicomposting by introducing Eisenia foetida species of earthworms for 30 days and the cytogenetic effects were reinvestigated through V. faba root meristems. Chemical analysis carried out prior to vermicomposting revealed high concentrations of heavy metals such as Cr, Cu, Pb, Zn, and Ni in FCS samples. CS samples also showed the presence of these metals. Cytogenetic examinations of root meristems exposed to the FCS mixtures showed significant inhibition of mitotic index (MI), induction of chromosome aberrations (CA), and a significantly increased frequency of mitotic aberrations (MA). The increase of the aberrations was dependent on the flyash concentrations. Roots grown in CS samples also showed chromosomal and MAs; however, the percentage was lower than that observed with FCS and also statistically nonsignificant. Cytogenetic analysis of vermicomposted samples of FCS revealed a 15-45% decline in the aberration frequencies whereas chemical analysis showed a 10-50% decline in the metal concentrations, viz. Cr, Cu, Pb, Zn, and Ni, which indicates E. foetida a potential accumulator of heavy metals and the decline in metal concentrations may be the cause of the decrease in aberration frequencies. The present study indicates the genotoxicity potential of flyash and also the feasibility of vermicomposting for cleanup of metal-contaminated soil to mitigate the toxicity/genotoxicity. Copyright 2004 Elsevier Inc.
Laboratory evaluation of flyash treated embankment and base materials : interim report No. 1.
DOT National Transportation Integrated Search
1986-06-01
This study was undertaken to provide the Louisiana DOTD with a data base from which decision-making information can be concerning the modification or stabilization of soils using flyash as a full or partial replacement for hydraulic cement or hydrate...
Cyclone as a precleaner to ESP--a need for Indian coal based thermal power plants.
George, K V; Manjunath, S; Rao, C V Chalapati; Bopche, A M
2003-11-01
Almost all coal based thermal power plants (CTPP) in India use electrostatic precipitator (ESP) for reduction of particulate matter (PM) in flue gas generated due to the combustion of Indian coal. This coal is characterized by high ash content, low calorific value and low sulfur content resulting in the generation of a very large amount of highly electrically-resistive fly-ash; thereby requiring a very large size ESP to minimize the fly-ash emissions. However, the flue-gas particle size distribution analysis showed that 60% of the particles are above 15 microm size, which can be conveniently removed using a low-cost inertial separator such as a cyclone separator. It is proposed that a cyclone be used, as a pre-cleaner to ESP so that the large size fraction of fly-ash can be removed in the pre-cleaning and the remaining flue-gas entering the ESP will then contain only small size particles with low dust loading, thereby requiring a small ESP, and improving overall efficiency of dust removal. A low efficiency (65%), high throughput cyclone is considered for pre-cleaning flue gas and the ESP is designed for removal of the remaining 35% fly-ash from the flue gas. It is observed that with 100% dust load, the ESP requires six fields per pass, whereas with cyclone as a pre-cleaner, it requires only five fields per pass. Introducing cyclone into the flue gas path results in additional head loss, which needs to be overcome by providing additional power to induced draft (ID) fan. The permissible head loss due to the cyclone is estimated by comparing the power requirement in the bag filter control unit and cyclone-ESP combined unit. It is estimated that a head loss of 10 cm of water can be permitted across the cyclone so as to design the same for 65% efficiency.
Effect of DMMP on the pyrolysis products of polyurethane foam materials in the gaseous phase
NASA Astrophysics Data System (ADS)
Liu, W.; Li, F.; Ge, X. G.; Zhang, Z. J.; He, J.; Gao, N.
2016-07-01
Dimethyl methylphosphonate (DMMP) has been used as a flame retardant containing phosphorus to decrease the flammability of the polyurethane foam material (PUF). Flame retardancy and thermal degradation of PUF samples have been investigated by the LOI tests and thermal analysis. The results show that LOI values of all PUF/DMMP samples are higher than that of the neat PUF sample and the LOI value of the samples increases with both DMMP concentration and the %P value. Thermal analysis indicates that flame retardant PUF shows a dominant condensed flame retardant activity during combustion. Thermogravimetric analysis-infrared spectrometry (TG-FTIR) has been used to study the influence of DMMP on the pyrolysis products in the gaseous phase during the thermal degradation of the PUF sample. Fourier transform infrared spectrometry (FTIR) spectra of the PUF sample at the maximum evolution rates and the generated trends of water and the products containing -NCO have been examined to obtain more information about the pyrolysis product evolutions of the samples at high temperature. These results reveal that although DMMP could improve the thermal stability of PUF samples through the formation of the residual char layer between fire and the decomposed materials, the influence of DMMP on the gaseous phase can be also observed during the thermal degradation process of materials.
CHARACTERIZATION OF ADVANCED SORBENTS FOR DRY SO2 CONTROL
The paper discusses the development of new flyash/lime sorbents for removing SO2 from coal-fired flue gas. Flyash/lime weight ratios of 1:1 to 10:1 and several additives to these sorbents for promoting their reactivity were evaluated in a bench-scale reactor simulating conditions...
Trained Inquiry Skills on Heat and Temperature Concepts
NASA Astrophysics Data System (ADS)
Hasanah, U.; Hamidah, I.; Utari, S.
2017-09-01
Inquiry skills are skills that aperson needs in developing concepts, but the results of the study suggest that these skills haven’t yet been trained along with the development of concepts in science feeding, found the difficulties of students in building the concept scientifically. Therefore, this study aims to find ways that are effective in training inquiry skills trough Levels of Inquiry (LoI) learning. Experimental research with one group pretest-postest design, using non-random sampling samples in one of vocational high school in Cimahi obtained purposively 33 students of X class. The research using the inquiry skills test instrument in the form of 15questions multiple choice with reliability in very high category. The result of data processing by using the normalized gain value obtained an illustration that the ways developed in the LoI are considered effective trained inquiry skills in the middle category. Some of the ways LoI learning are considered effective in communicating aspects through discovery learning, predicting trough interactive demonstration, hypotheses through inquiry lesson, and interpreting data through inquiry lab, but the implementation of LoI learning in this study hasn’t found a way that is seen as effective for trespassing aspects of designing an experiment.
Fly-ash geo-polymer foamed concrete
NASA Astrophysics Data System (ADS)
Kargin, Aleksey; Baev, Vladimir; Mashkin, Nikolay
2017-01-01
In recent years, the interest of researchrs in using fly-ash as a raw material for the geo-polymer synthesis is increasing. Kuzbass region (in Russia) has a large amount of ash wastes generated, which defined the relevace of the study performed in this paper. Results of investigating load-bearing capacity of structural insulating material produced by geo-polymerization of fly-ash of Kemerovo hydro-electric power plant with the addition of complex activator are described in the paper. Hydrogen peroxide solution was used as the foaming agent. The activation time, the temperature of isothermal holding and hardening in normal conditions for all samples were constant. The compressive strength and the mean density of geo-polymer foamed concrete were determined. The influence of the material composition on its properties was revealed. It is found that of the geo-polymer foamed concrete with the optimum composition has hardness of 1,1-3,5 MPa at the density of 400 to 900 kg/m3. Thus, the production of the fly-ash geo-polymer concretes and mortars is feasible, justified and promising.
Volli, Vikranth; Purkait, M K
2015-10-30
This work discusses the utilization of flyash for synthesis of heterogeneous catalyst for transesterification. Different types of zeolites were synthesized from alkali fusion followed by hydrothermal treatment of coal flyash as source material. The synthesis conditions were optimized to obtain highly crystalline zeolite based on degree of crystallinity and cation exchange capacity (CEC). The effect of CEC, acid treatment, Si/Al ratio and calcination temperature (800, 900 and 1000 °C) on zeolite formation was also studied. Pure, single phase and highly crystalline zeolite was obtained at flyash/NaOH ratio (1:1.2), fusion temperature (550 °C), fusion time (1 h), hydrothermal temperature (110 °C) and hydrothermal time (12h). The synthesized zeolite was ion-exchanged with potassium and was used as catalyst for transesterification of mustard oil to obtain a maximum conversion of 84.6% with 5 wt% catalyst concentration, 12:1 methanol to oil molar ratio, reaction time of 7 h at 65 °C. The catalyst was reused for 3 times with marginal reduction in activity. Copyright © 2015 Elsevier B.V. All rights reserved.
NASA Astrophysics Data System (ADS)
Doherty, R.; Phillips, D. H.; McGeough, K. L.; Walsh, K. P.; Kalin, R. M.
2006-05-01
A sequential biological permeable reactive barrier (PRB) was determined to be the best option for remediating groundwater that has become contaminated with a wide range of organic contaminants (i.e., benzene, toluene, ethylbenzene, xylene and polyaromatic hydrocarbons), heavy metals (i.e., lead and arsenic), and cyanide at a former manufactured gas plant after 150 years of operation in Portadown, Northern Ireland. The objective of this study was to develop a modified flyash that could be used in the initial cell within a sequential biological PRB to filter complex contaminated groundwater containing ammonium. Flyash modified with lime (CaOH) and alum was subjected to a series of batch tests which investigated the modified cation exchange capacity (CEC) and rate of removal of anions and cations from the solution. These tests showed that a high flyash composition medium (80%) could remove 8.65 mol of ammonium contaminant for every kilogram of medium. The modified CEC procedure ruled out the possibility of cation exchange as the major removal mechanism. The medium could also adsorb anions as well as cations (i.e., Pb and Cr), but not with the same capacity. The initial mechanism for Pb and Cr removal is probably precipitation. This is followed by sorption, which is possibly the only mechanism for the removal of dichromate anions. Scanning electron microscopic analysis revealed very small (<1 μm) cubic highly crystalline precipitates on the flyash, although this new crystalline zeolite growth did not occur rapidly enough to enable productive zeolite formation. Surface area measurements showed that biofilm growth on the medium could be a major factor in the comparative reduction of surface area between real and synthetic contaminant groundwaters. The modified flyash was found to be a highly sorptive granular material that did not inhibit microbiological activity, however, leaching tests revealed that the medium would fail as a long-term barrier material.
NASA Astrophysics Data System (ADS)
Venkata Reddy, V.; Gopi Krishna, M.; Praveen Kumar, K.; Naga Kishore, B. S.; Babu Rao, J.; Bhargava, NRMR
2018-02-01
Experiments have been performed under laboratory condition to review the mechanical behaviour of the hybrid composites with aluminium matrix A7075 alloy, reinforced with silicon carbide (SiC) and Flyash. This has been possible by fabricating the samples through usual stir casting technique. Scanning electron microscopy was used for microstructure analysis. Chemical characterization of both matrix and composites was performed by using EDAX. Density, hardness, tensile and deformation studies were conceded out on both the base alloy and composites. Enhanced hardness and deformed properties were observed for all the composites. Interestingly improved tensile results were obtained for the composites than alloy. Dispersion of (SiC) and Flyash particles in aluminium matrix enhances the hardness of the composites.
Belharazem, Djeda; Magdeburg, Julia; Berton, Ann-Kristin; Beissbarth, Li; Sauer, Christian; Sticht, Carsten; Marx, Alexander; Hofheinz, Ralf; Post, Stefan; Kienle, Peter; Ströbel, Philipp
2016-10-01
Loss of imprinting (LOI) of the insulin-like growth factor 2 (IGF2) is an early event in the development of colorectal cancer (CRC). Whether LOI of IGF2 denotes a molecular or clinical cancer subgroup is currently unknown. Tumor biopsies and paired normal mucosa from 399 patients with extensive clinical annotations were analyzed for LOI and IGF2 expression. LOI status in 140 informative cases was correlated with clinicopathologic parameters and outcome. LOI was frequent in normal mucosa and tumors and occurred throughout the large intestine. LOI was unrelated to microsatellite instability, KRAS mutation status, stage, and survival. However, CRC with LOI showed increased IGF2 protein levels and activation of AKT1. Gene expression analysis of tumors with and without LOI and knockdown of IGF2 in cell lines revealed that IGF2 induced distinct sets of activated and repressed genes, including Wnt5a, CEACAM6, IGF2BP3, KPN2A, BRCA2, and CDK1. Inhibition of AKT1 in IGF2-stimulated cells showed that the downstream effects of IGF2 on cell proliferation and gene expression were strictly AKT1-dependent. LOI of IGF2 is a frequent and early event in CRC that occurs both in the adenomatous polyposis coli (APC) gene-mutated and serrated route of carcinogenesis. LOI leads to overexpression of IGF2, activates IGF1R and AKT1, and is a powerful driver of cell proliferation. Moreover, our results suggest that IGF2 via AKT1 also contributes to non-canonical wnt signaling. Although LOI had no significant impact on major clinical parameters and outcome, its potential as a target for preventive and therapeutic interventions merits further investigation.
Basak, Santanu; Wazed Ali, S
2018-07-15
Three different wastage plant based bio-molecules named banana peel powder (Musa acuminata) (BPP), coconut shell (Cocos nucifera) extract (CSE) and pomegranate rind (Punica granatum) extract (PRE) have been explored as fire resistant material on the cellulosic polymer (cotton fabric). To this end, extracts have been applied to the cotton fabric in different concentration at elevated temperature for specific time period. Treated cotton fabric showed 6 (BPP), 8.5 (CSE) and 12 (PRE) times lower vertical burning rate compared to the control cotton fabric. Thermo-gravimetry (TG) curves and the limiting oxygen index (LOI) value revealed that the PRE extract (LOI: 32) treated fabric encompassed more thermal stability compared to the BPP (LOI:26) and the CSE (LOI: 27) treated fabric as it showed higher oxygen index and more weight retention (40%) at higher temperature 450°C. Moreover, the carbonaceous samples remained after the burning of the extracts and the treated fabrics showed structural integration and more carbon content [65.6 (PRE extract) and 76.3% (PRE treated cotton)] compared to the fragile, net like char of the control cotton fabric, having less carbon content (49.8%). Gas Chromatography Mass spectroscopy (GC-MS) of the different extracts (CSE, PRE, BPP) used for the study showed the presence of high molecular weight aromatic phenolic compounds, tannin based compound and the nitrogen containing alkaloids, responsible for fire resistant effect of the different extract treated fabric. Besides fire retardancy, all the treated fabric showed attractive natural colour (measured by colour strength values) and there has been no adverse effect on the tensile strength property of the fabric after the treatment. Copyright © 2018 Elsevier B.V. All rights reserved.
Use of fly-ash slurry in backfill grouting in coal mines.
Jiang, Ning; Zhao, Jinhai; Sun, Xizhen; Bai, Liyang; Wang, Changxiang
2017-11-01
Cave backfill grouting implies grouting of the caving rock mass prior to it being compacted. The filling materials strengthen the caving rock and support the overlying strata to achieve the purpose of slowing down the surface subsidence. The broken roof will fail and collapse during mining operations performed without appropriate supporting measures being taken. It is difficult to perform continuous backfill mining on the working face of such roofs using the existing mining technology. In order to solve the above problems, fly ash and mine water are considered as filling materials, and flow characteristics of fly-ash slurry are investigated through laboratory experiments and theoretical analyses. Laws governing the diffusion of fly-ash slurry in the void of caving rock masses and in the void between a caving rock mass and a basic roof are obtained and verified. Based on the results obtained from the above analyses and actual conditions at the Zhaoguan coal mine, Shandong Province, China, a cave backfill grouting system of the hauling pipeline is developed and successfully tested at the 1703 working face in the Zhaoguan coal mine. The results demonstrate that a filling rate of 43.46% is achieved, and the surface subsidence coefficient of the grouting process is found to be 0.475. Compared to the total caving method, the proposed system is found to achieve a reduction rate of 40.63%. This effectively helps in lowering the value of the surface subsidence coefficient. Fly ash and mine water, considered as primary materials in this study, also play a significant role in improving the air quality and water environment.
Innovative Solidification Techniques for Hazardous Wastes at Army Installations.
1985-11-01
Fixed Hazardous Industrial Wastes and Flue Gas Desulfurization Sludges," Interim Report, EPA-600/2-76-182, US Environmental Protection Agency... flue gas . Flyash from coal-fired power plants is an almost entirely inorganic product having a glassy nature. Consequently, flyash by itself has little...effective- ness of alternative control strategies for reducing environmental impacts. 4. % 46 -"- °° ~~~~~...-.-..o
Using bromine gas to enhance mercury removal from flue gas of coal-fired power plants.
Liu, Shou-Heng; Yan, Nai-Qiang; Liu, Zhao-Rong; Qu, Zan; Wang, H Paul; Chang, Shih-Ger; Miller, Charles
2007-02-15
Bromine gas was evaluated for converting elemental mercury (Hg0) to oxidized mercury, a form that can readily be captured by the existing air pollution control device. The gas-phase oxidation rates of Hg0 by Br2 decreased with increasing temperatures. SO2, CO, HCl, and H2O had insignificant effect, while NO exhibited a reverse course of effect on the Hg0 oxidation: promotion at low NO concentrations and inhibition at high NO concentrations. A reaction mechanism involving the formation of van der Waals clusters is proposed to accountfor NO's reverse effect. The apparent gas-phase oxidation rate constant, obtained under conditions simulating a flue gas without flyash, was 3.61 x 10(-17) cm3 x molecule(-1) x s(-1) at 410 K corresponding to a 50% Hg0 oxidation using 52 ppm Br2 in a reaction time of 15 s. Flyash in flue gas significantly promoted the oxidation of Hg0 by Br2, and the unburned carbon component played a major role in the promotion primarily through the rapid adsorption of Br2 which effectively removed Hg0 from the gas phase. At a typical flue gas temperature, SO2 slightly inhibited the flyash-induced Hg0 removal. Conversely, NO slightly promoted the flyash induced Hg0 removal by Br2. Norit Darco-Hg-LH and Darco-Hg powder activated carbons, which have been demonstrated in field tests, were inferred for estimating the flyash induced Hg0 oxidation by Br2. Approximately 60% of Hg0 is estimated to be oxidized with the addition of 0.4 ppm of gaseous Br2 into full scale power plant flue gas.
On the removal of hexavalent chromium from a Class F fly ash.
Huggins, F E; Rezaee, M; Honaker, R Q; Hower, J C
2016-05-01
Coarse and fine samples of a Class F fly ash obtained from commercial combustion of Illinois bituminous coal have been exposed to two long-term leaching tests designed to simulate conditions in waste impoundments. ICP-AES analysis indicated that the coarse and fine fly ash samples contained 135 and 171mg/kg Cr, respectively. Measurements by XAFS spectroscopy showed that the ash samples originally contained 5 and 8% of the chromium, respectively, in the hexavalent oxidation state, Cr(VI). After exposure to water for more than four months, the percentage of chromium as Cr(VI) in the fly-ash decreased significantly for the coarse and fine fly-ash in both tests. Combining the XAFS data with ICP-AES data on the concentration of chromium in the leachates indicated that, after the nineteen-week-long, more aggressive, kinetic test on the coarse fly ash, approximately 60% of the Cr(VI) had been leached, 20% had been reduced to Cr(III) and retained in the ash, and 20% remained as Cr(VI) in the ash. In contrast, during the six-month-long baseline test, very little Cr was actually leached from either the coarse or the fine fly-ash (<0.1mg/kg); rather, about 66% and 20%, respectively, of the original Cr(VI) in the coarse and fine fly-ash was retained in the ash in that form, while the remainder, 34% and 80%, respectively, was reduced and retained in the ash as Cr(III). The results are interpreted as indicating that Cr(VI) present in Class F fly-ash can be reduced to Cr(III) when in contact with water and that such chemical reduction can compete with physical removal of Cr(VI) from the ash by aqueous leaching. Copyright © 2016 Elsevier Ltd. All rights reserved.
Schmitz, J
1985-10-01
More than 350 dumps of mines and industries in two federal states of the FRG were recorded, measured radiometrically, evaluated, and some of them sampled. Most of the mine dumps belonged to old and smaller residues from lead/zinc and iron ore mining, while the largest depositions contain tailings of modern ore beneficiation or flyash disposal. All mine dumps from uranium exploration in Baden-Württemberg and Bavaria were investigated. The highest doses, up to 100 mSv/a, were found on the piles of the uranium exploration. These depositions, which are supervised and licensed, are followed, in terms of surface dose, by the old uncontrolled mine dumps of silver/cobalt mining with doses up to 20 mSv/a. The numerous porphyry and granite quarries show doses between 1 and 2 mSv/a, as do flyash and slag dumps. The lowest doses were found on the dumps of the hydrothermal Pb/Zn and iron ore deposits, while the slag piles of iron ore processing showed higher thorium values. Assays for Ra-226 and Pb-210 of the materials deposited confirmed the radiometric results. Analyses of seepage waters and gallery waters showed only very few values exceeding the derived drinking water concentrations.
Utility of the Leyton Obsessional Inventory to distinguish OCD and OCPD.
Wellen, David; Samuels, Jack; Bienvenu, O Joseph; Grados, Marco; Cullen, Bernadette; Riddle, Mark; Liang, Kung-Yee; Nestadt, Gerald
2007-01-01
The Leyton Obsessional Inventory (LOI) is a self-report questionnaire that assesses obsessional symptoms. The ability of the LOI to distinguish between obsessive-compulsive disorder (OCD) and obsessive-compulsive personality disorder (OCPD) has not been adequately addressed. Our purpose is to identify dimensions of obsessional symptoms from the LOI and determine how well they distinguish between OCD and OCPD. The LOI was completed by 488 participants diagnosed by trained clinicians. Factor analysis was performed on responses to the interference items of the LOI. The relationship between the factors, OCD and OCPD was evaluated using logistic regression. Five factors underlying the LOI were identified: (I) obsessional ruminations and compulsions, (II) ordering and arranging, (III) organizing activities, (IV) contamination, and (V) parsimony. Factors I, III, and IV were strongly associated with OCD. Only Factor II was associated with OCPD. Factor IV was negatively associated with obsessive-compulsive personality traits. LOI factors are useful in discriminating between OCD and OCPD. Obsessional ruminations and compulsions, organizing activities, and contamination fears may indicate OCD, and ordering and arranging symptoms may indicate OCPD rather than OCD. Parsimony may indicate neither disorder, and contamination, the absence of OCPD traits compared with the other LOI factors. These findings may contribute to effective diagnosis and treatment by allowing the LOI to screen for OCD and OCPD in a population exhibiting obsessional symptoms and traits.
Separation of particulate from flue gas of fossil fuel combustion and gasification
Yang, Wen-Ching; Newby, Richard A.; Lippert, Thomas E.
1997-01-01
The gas from combustion or gasification of fossil fuel contains flyash and other particulate. The flyash is separated from the gas in a plurality of standleg moving granular-bed filter modules. Each module includes a dipleg through which the bed media flows into the standleg. The bed media forms a first filter bed having an upper mass having a first frusto-conical surface in a frusto-conical member at the entrance to the standleg and a lower mass having a second frusto-conical surface of substantially greater area than the first surface after it passes through the standleg. A second filter media bed may be formed above the first filter media bed. The gas is fed tangentially into the module above the first surface. The flyash is captured on the first frusto-conical surface and within the bed mass. The processed gas flows out through the second frusto-conical surface and then through the second filter bed, if present. The bed media is cleaned of the captured flyash and recirculated to the moving granular bed filter. Alternatively, the bed media may be composed of the ash from the combustion which is pelletized to form agglomerates. The ash flows through the bed only once; it is not recycled.
Anthropogenic Influences on Estuarine Sedimentation in Salem Sound, MA
NASA Astrophysics Data System (ADS)
Kristiansen, E. R.; Hubeny, J. B.; Zhu, J.; Olsen, C. R.; Warren, B.
2010-12-01
The Salem Sound watershed (MA) historically has been a region of significant industrial activity. Two specific point sources for pollution in the region are the South Essex Sewerage District (SESD) wastewater treatment facility, and the Salem Harbor Power Station, a coal-burning power plant. This study tests the hypothesis that human impact on Salem Sound is preserved in the sediment record. A sediment core was taken near the location of the SESD outfall. This core was analyzed for content of organic matter via loss on ignition (LOI), as well as magnetic susceptibility. An age model was constructed using 137Cs and 210Pb. Below 31 cm (mid-nineteenth century), the core contains mean background values of 2.7% LOI and values increase above this depth. At 21cm, a rapid increase in organic matter concentration from 6.6% to 11.8% is observed. This depth corresponds to ~1905 which is contemporaneous with construction of the outfall pipe discharging raw wastewater. At a depth of 7 cm (mid 1970s), LOI values decrease from 11.7% to 9.3%. This shift is likely attributed to SESD beginning primary treatment in 1977. LOI values continue to drop at 2cm (late 1990s), from 7.8% to 6.3%, and remain at 6.1% to the modern surface, likely a result of SESD upgrading to secondary treatment in 1998. Magnetic susceptibility also shows variability down core that is likely attributed to human impact. At a depth of approximately 20cm susceptibility values start increasing from 4.2 SI units until they reach a peak at 15cm (8.8 SI units). This increase can be attributed to the industrial revolution and increased industrial activity in the area. A decrease in susceptibility is observed at 15cm to 11cm (5.6 SI units) that may be attributed to the Great Depression and less fossil fuels being burned due to the economic situation. At approximately 10cm and 8.0 SI units, an increasing trend is first observed. This trend continues up to the modern surface where it eventually reaches 19.9 SI units. This depth of 10cm coincides with the construction of the Salem Harbor Station in 1952, and the increasing trend can therefore most likely be explained by the proximal power plant burning coal.
Possible involvement of loss of imprinting in immortalization of human fibroblasts.
Okamura, Kotaro; Ohno, Maki; Tsutsui, Takeki
2011-04-01
Disruption of the normal pattern of parental origin-specific gene expression is referred to as loss of imprinting (LOI), which is common in various cancers. To investigate a possible role of LOI in the early stage of human cell transformation, we studied LOI in 18 human fibroblast cell lines immortalized spontaneously, by viral oncogenes, by chemical or physical carcinogens, or by infection with a retrovirus vector encoding the human telomerase catalytic subunit, hTERT cDNA. LOI was observed in all the 18 immortal cell lines. The gene most commonly exhibiting LOI was NDN which displayed LOI in 15 of the 18 cell lines (83%). The other genes exhibiting LOI at high frequencies were PEG3 (50%), MAGE-L2 (61%) and ZNF 127 (50%). Expression of NDN that was lost in the immortal cell lines was restored by treatment with 5-aza-2'-deoxycytidine. The ratio of histone H3 lysine 9 methylation to histone H3 lysine 4 methylation of the chromatin containing the NDN promoter in the immortal WI-38VA13 cells was greater than that in the parental cells, suggesting chromatin structure-mediated regulation of NDN expression. We previously demonstrated that inactivation of the p16INK4a/pRb pathway is necessary for immortalization of human cells. Human fibroblasts in the pre-crisis phase and cells with an extended lifespan that eventually senesce, both of which have the normal p16INK4a/pRb pathway, did not show LOI at any imprinted gene examined. Although it is not clear if LOI plays a causal role in immortalization of human cells or is merely coincidental, these findings indicate a possible involvement of LOI in immortalization of human cells or a common mechanism involved in both processes.
Aluminum phosphate microcapsule flame retardants for flexible polyurethane foams
NASA Astrophysics Data System (ADS)
Zhang, Bin; Liu, Hong; Han, Jian
2018-04-01
In this study, highly efficient flame-retardant aluminum phosphate (ALP) microcapsules were synthesized from ALP and ammonium phosphomolybdate trihydrate. The chemical structure of the ALP microcapsules was characterized by scanning electron microscopy and elemental analysis, and the thermal degradation behavior was investigated by thermogravimetric analysis (TGA). Subsequently, flexible polyurethane (PU) foams were prepared with the ALP microcapsules. Limiting oxygen index (LOI) tests, vertical burning tests, smoke density rating (SDR), and cone calorimetric tests were employed to investigate the combustion of the materials. The results showed that the flexible PU foams with 15 parts per hundred polyol by weight (pphp) ALP microcapsules passed the vertical burning test and they had an increased LOI value of 28.5%. The SDR value for PU/20 pphp ALP microcapsule composites was about 16.0% and the SDR value for the pure PU was about 29.0%. The corresponding flame-retardant mechanism was investigated by Fourier transform infrared spectroscopy, TGA, Pyrolysis Gas Chromatography Mass Spectrometry (Py-GC/MS) tests, and energy-dispersive X-ray spectrometry.
Chang, Shih-ger [El Cerrito, CA; Liu, Shou-heng [Kaohsiung, TW; Liu, Zhao-rong [Beijing, CN; Yan, Naiqiang [Berkeley, CA
2009-01-20
Disclosed herein is a method for removing mercury from a gas stream comprising contacting the gas stream with a getter composition comprising bromine, bromochloride, sulphur bromide, sulphur dichloride or sulphur monochloride and mixtures thereof. In one preferred embodiment the getter composition is adsorbed onto a sorbent. The sorbent may be selected from the group consisting of flyash, limestone, lime, calcium sulphate, calcium sulfite, activated carbon, charcoal, silicate, alumina and mixtures thereof. Preferred is flyash, activated carbon and silica.
Chang, Shih-Ger [El Cerrito, CA; Liu, Shou-Heng [Kaohsiung, TW; Liu, Zhao-Rong [Beijing, CN; Yan, Naiqiang [Berkeley, CA
2011-08-30
Disclosed herein is a method for removing mercury from a gas stream comprising contacting the gas stream with a getter composition comprising bromine, bromochloride, sulphur bromide, sulphur dichloride or sulphur monochloride and mixtures thereof. In one preferred embodiment the getter composition is adsorbed onto a sorbent. The sorbent may be selected from the group consisting of flyash, limestone, lime, calcium sulphate, calcium sulfite, activated carbon, charcoal, silicate, alumina and mixtures thereof. Preferred is flyash, activated carbon and silica.
Chang, Shih-ger; Liu, Shou-heng; Liu, Zhao-rong; Yan, Naiqiang
2010-07-13
Disclosed herein is a method for removing mercury from a gas stream comprising contacting the gas stream with a getter composition comprising bromine, bromochloride, sulphur bromide, sulphur dichloride or sulphur monochloride and mixtures thereof. In one preferred embodiment the getter composition is adsorbed onto a sorbent. The sorbent may be selected from the group consisting flyash, limestone, lime, calcium sulphate, calcium sulfite, activated carbon, charcoal, silicate, alumina and mixtures thereof. Preferred is flyash, activated carbon and silica.
Yaofa, Jiang; Elswick, E.R.; Mastalerz, Maria
2008-01-01
Sulfur occurs in multiple mineral forms in coals, and its fate in coal combustion is still not well understood. The sulfur isotopic composition of coal from two coal mines in Indiana and fly ash from two power plants that use these coals were studied using geological and geochemical methods. The two coal beds are Middle Pennsylvanian in age; one seam is the low-sulfur ( 5%) Springfield Coal Member of the Petersburg Formation. Both seams have ash contents of approximately 11%. Fly-ash samples were collected at various points in the ash-collection system in the two plants. The results show notable difference in ??34S for sulfur species within and between the low-sulfur and high-sulfur coal. The ??34S values for all sulfur species are exclusively positive in the low-sulfur Danville coal, whereas the ??34S values for sulfate, pyritic, and organic sulfur are both positive and negative in the high-sulfur Springfield coal. Each coal exhibits a distinct pattern of stratigraphic variation in sulfur isotopic composition. Overall, the ??34S for sulfur species values increase up the section in the low-sulfur Danville coal, whereas they show a decrease up the vertical section in the high-sulfur Springfield coal. Based on the evolution of ??34S for sulfur species, it is suggested that there was influence of seawater on peat swamp, with two marine incursions occurring during peat accumulation of the high-sulfur Springfield coal. Therefore, bacterial sulfate reduction played a key role in converting sulfate into hydrogen sulfide, sulfide minerals, and elemental sulfur. The differences in ??34S between sulfate sulfur and pyritic sulfur is very small between individual benches of both coals, implying that some oxidation occurred during deposition or postdeposition. The ??34S values for fly ash from the high-sulfur Springfield coal (averaging 9.7???) are greatly enriched in 34S relative to those in the parent coal (averaging 2.2???). This indicates a fractionation of sulfur isotopes during high-sulfur coal combustion. By contrast, the ??34S values for fly-ash samples from the low-sulfur Danville coal average 10.2???, only slightly enriched in 34S relative to those from the parent coal (average 7.5???). The ??34S values for bulk S determined directly from the fly-ash samples show close correspondence with the ??34S values for SO4- 2 leached from the fly ash in the low-sulfur coal, suggesting that the transition from pyrite to sulfate occurred via high-temperature oxidation during coal combustion. ?? 2007 Elsevier B.V. All rights reserved.
Das, Avijit; Patel, Subhra Sarita; Kumar, Rajeev; Krishna, K V S S; Dutta, Saikat; Saha, Manik Chandra; Sengupta, Siladitya; Guha, Dipayan
2018-04-01
A geochemical study of the trace metals and lead isotopic ratios of soil and sediments in Korba, Chhattisgarh, India is presented here for the first time. Korba, the nation's 'power hub' is also the fifth among its eighty-eight most critically polluted industrial hotspots. A very high mean concentration (in mg kg-1) of V (308), Cr (567), Mn (3442), Co (92), Cu (218), Zn (426), Pb (311), Th (123) and U (32) characterized the sediments of the studied area with mean I geo values of the trace metals ranging from -2.29 to 3.27. In the two-ratio scatter Pb isotope plot of the different environmental matrices, except for human blood, coal, soil, sediments, non-washed leaves, flyash and diesel overlapped linearly in the mixing line between diesel as the highest anthropogenic end member and a core sediment fraction representing its geogenic counterpart. The mean 207 Pb/ 206 Pb Pb ratio decreased in the order of diesel (0.9012) > flyash (0.8757) > coal (0.8498) soils and sediments (0.8374) > lowest core sediment fraction (0.8017). Principal Component Analysis (PCA) of the trace metal data extracted V, Cr, Cu, Zn, Pb, U and Th in the first component PC1. The northeastern part of the study area revealed major hotspots of V, Cu, Co, Zn and Pb near the flyash dykes of the power stations. Human blood used as a biomarker for Pb pollution in this study had a mean blood lead level of 28 μg/dl with a distinctive high 207 Pb/ 206 Pb ratio of 0.8828. Published by Elsevier Ltd.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Scott, A.N.; Thomas, M.D.A.
An investigation of fly ash (FA) produced from various blends of coal and petroleum coke (pet coke) fired at Belledune Generating Station, New Brunswick, Canada, was conducted to establish its performance relative to FA derived from coal-only combustion and its compliance with CSA A3000. The FA samples were beneficiated by an electrostatic separation process to produce samples for testing with a range of loss-on-ignition (LOI) values. The results of these studies indicate that the combustion of pet coke results in very little inorganic residue (for example, typically less than 0.5% ash) and the main impact on FA resulting from themore » co-combustion of coal and up to 25% pet coke is an increase in the unburned carbon content and LOI values. The testing of FA after beneficiation indicates that FA produced from fuels with up to 25% pet coke performs as good as FA produced from the same coal without pet coke.« less
Effect of levels of inquiry model of science teaching on scientific literacy domain attitudes
NASA Astrophysics Data System (ADS)
Achmad, Maulana; Suhandi, Andi
2017-05-01
The aim of this research was to obtain an overview of the increase scientific literacy attitudes domain in high school students as the effects of the Levels of Inquiry (LOI) model of science teaching. This research using a quasi-experimental methods and randomizedpretest-posttest control group design. The subject of this research was students of grade X in a senior high school in Purwakarta and it consists of two classes who were divided into experimental class (30 students) and control class (30 students). While experimental class was taught LOIand control class was taught Interactive Lecture Demonstration (ILD). Data were collected using an attitude scale scientific literacy test which is based on the Likert scale. Data were analyzed using normality test, homogeneity test, and t-test to the value of N-gain attitude of scientific literacy scale test. The result of percentage average N-gain experimental class and control are 49 and 31 that classified into medium improvement category. Based on the results of hypothesis testing on the N-gain value obtained by the Sig.(One-tailed) 0.000 < 0.050, it means that H1 was accepted. The results showed that scientific literacy domain attitude of students who got learning by LOI is higher than students who got learning by ILD. It can be concluded that the effect of LOI is better to improve scientific literacy domain attitudes significantly.
Silk flame retardant finish by ternary silica sol containing boron and nitrogen
NASA Astrophysics Data System (ADS)
Zhang, Qiang-hua; Chen, Guo-qiang; Xing, Tie-ling
2017-11-01
A ternary flame retardant sol system containing Si, B and N was prepared via sol gel method using tetraethoxysilane (TEOS) as a precursor, boric acid (H3BO3) and urea (CO(NH2)2) as flame retardant additives and then applied to silk fabric flame retardant finish. The FT-IR and SEM results showed that the nitrogen-boron-silica ternary sol was successfully prepared and entrapped onto the surface of silk fibers. The limiting oxygen index (LOI) test indicated that the silk fabric treated with 24% boric acid and 6% urea (relative to the TEOS) doped ternary silica sol system performed excellent flame retardancy with the LOI value of 34.6%. Furthermore, in order to endow silk fabric with durable flame retardancy, the silk fabric was pretreated with 1,2,3,4-butanetetracarboxylic acid (BTCA) before the ternary sol system treatment. The BTCA pretreat ment applied to silk could effectively promote the washing durability of the ternary sol, and the LOI value of the treated sample after 10 times washing could still maintain at 30.8% compared with that of 31.0% before washing. Thermo gravimetric (TG), micro calorimeter combustion (MCC) and smoke density test results demonstrated that the thermal stability, heat release and smoke suppression of the nitrogen-boron-silica ternary system decreased somewhat compared with the boron-silica binary flame retardant system.
Woodson, Karen; Flood, Andrew; Green, Lisa; Tangrea, Joseph A; Hanson, Jeffrey; Cash, Brooks; Schatzkin, Arthur; Schoenfeld, Phillip
2004-03-03
Loss of imprinting (LOI) of insulin-like growth factor-II (IGF-II) may be an inherited epigenetic trait that is polymorphic in the population, and its presence may predispose an individual to the development of colorectal cancer. We evaluated the association between LOI of IGF-II in normal colonic mucosal samples and adenomas in women participating in a colonoscopy screening study. Among 40 participants, 11 (27.5%) had LOI of IGF-II in their normal colonic mucosal tissue. After adjusting for body mass index and family history of colorectal cancer, LOI status was associated with a fivefold increased risk of adenoma formation (odds ratio = 5.2, 95% confidence interval = 1.0 to 26.7). On average, IGF-II expression was more than threefold higher among women with LOI of IGF-II than among women with normal imprinting status. Our findings support the hypothesis that LOI of IGF-II is an epigenetic trait polymorphic in the population and suggest that LOI of IGF-II may play a role in colorectal cancer. These findings are intriguing and need to be confirmed in larger studies.
USSR Report, Engineering and Equipment
1986-08-13
JlHHHpoM H racHTeJiex B JIHHHK Ha- THeTaHH« aa racHTe/iew (ycpeAKeHHCx1 3Ha" ;:’ HHO ) i. \\ TpyOa-racHTcnb 400 MM {puc~ 4) =2,5 MTIa...reliable operation of fly-ash collectors in the period between overhauls of boilers . The walls of the modernized fly-ash collectors, in spite of...capacity of boiler , t/h Reduced ash content of fuel, %/ /(MJ/kg) [Continued on following page] Mixture of Donetsk coal 608-612 1.3-1.45 18
40 CFR Appendix A to Subpart Nnn... - Method for the Determination of LOI
Code of Federal Regulations, 2013 CFR
2013-07-01
... LOI 1. Purpose The purpose of this test is to determine the LOI of cured blanket insulation. The.... 2.2Furnace designed to heat to at least 540 °C (1,000 °F) and controllable to ±10 °C (50 °F). 2...
40 CFR Appendix A to Subpart Nnn... - Method for the Determination of LOI
Code of Federal Regulations, 2014 CFR
2014-07-01
... LOI 1. Purpose The purpose of this test is to determine the LOI of cured blanket insulation. The.... 2.2Furnace designed to heat to at least 540 °C (1,000 °F) and controllable to ±10 °C (50 °F). 2...
Roy, Uttariya; Sengupta, Shubhalakshmi; Banerjee, Priya; Das, Papita; Bhowal, Avijit; Datta, Siddhartha
2018-06-18
This study focuses on the investigation of removal of textile dye (Reactive Yellow) by a combined approach of sorption integrated with biodegradation using low cost adsorbent fly ash immobilized with Pseudomonas sp. To ensure immobilization of bacterial species on treated fly ash, fly ash with immobilized bacterial cells was characterized using Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and fluorescence microscopy. Comparative batch studies were carried out using Pseudomonas sp, fly ash and immobilized Pseudomonas sp on flyash and were observed that immobilized Pseudomonas sp on flyash acted as better decolourizing agent. The optimized pH, temperature, and immobilized adsorbent dosage for highest percentage of dye removal were observed to be pH 6, 303 K, 1.2 g/L in all the cases. At optimum condition, the highest percentage of dye removal was found to be 88.51%, 92.62% and 98.72% for sorption (flyash), biodegradation (Pseudomonas sp) and integral approach (Pseudomonas sp on flyash) respectively. Optimization of operating parameters of textile dye decolourization was done by response surface methodology (RSM) using Design Expert 7 software. Phytotoxicity evaluation with Cicer arietinum revealed that seeds exposed to untreated dye effluents showed considerably lower growth, inhibited biochemical, and enzyme parameters with compared to those exposed to treated textile effluents. Thus this immobilized inexpensive technique could be used for removal of synthetic dyes present in textile wastewater. Copyright © 2018 Elsevier Ltd. All rights reserved.
NASA Astrophysics Data System (ADS)
Beuria, P. C.; Biswal, S. K.; Mishra, B. K.; Roy, G. G.
2017-03-01
The kinetics of removal of loss on ignition (LOI) by thermal decomposition of hydrated minerals present in natural iron ores (i.e., kaolinite, gibbsite, and goethite) was investigated in a laboratory-scale vertical fluidized bed reactor (FBR) using isothermal methods of kinetic analysis. Experiments in the FBR in batch processes were carried out at different temperatures (300 to 1200°C) and residence time (1 to 30 min) for four different iron ore samples with various LOIs (2.34wt% to 9.83wt%). The operating velocity was maintained in the range from 1.2 to 1.4 times the minimum fluidization velocity ( U mf). We observed that, below a certain critical temperature, the FBR did not effectively reduce the LOI to a desired level even with increased residence time. The results of this study indicate that the LOI level could be reduced by 90% within 1 min of residence time at 1100°C. The kinetics for low-LOI samples (<6wt%) indicates two different reaction mechanisms in two temperature regimes. At lower temperatures (300 to 700°C), the kinetics is characterized by a lower activation energy (diffusion-controlled physical moisture removal), followed by a higher activation energy (chemically controlled removal of LOI). In the case of high-LOI samples, three different kinetics mechanisms prevail at different temperature regimes. At temperature up to 450°C, diffusion kinetics prevails (removal of physical moisture); at temperature from 450 to 650°C, chemical kinetics dominates during removal of matrix moisture. At temperatures greater than 650°C, nucleation and growth begins to influence the rate of removal of LOI.
Contributions of organic and inorganic matter to sediment ...
A mixing model derived from first principles describes the bulk density (BD) of intertidal wetland sediments as a function of loss on ignition (LOI). The model assumes the bulk volume of sediment equates to the sum of self-packing volumes of organic and mineral components or BD = 1/[LOI/k1 + (1-LOI)/k2], where k1 and k2 are the self-packing densities of the pure organic and inorganic components, respectively. The model explained 78% of the variability in total BD when fitted to 5075 measurements drawn from 33 wetlands distributed around the conterminous United States. The values of k1 and k2 were estimated to be 0.085 ± 0.0007 g cm-3 and 1.99 ± 0.028 g cm-3, respectively. Based on the fitted organic density (k1) and constrained by primary production, the model suggests that the maximum steady state accretion arising from the sequestration of refractory organic matter is ≤ 0.3 cm yr-1. Thus, tidal peatlands are unlikely to survive indefinitely a higher rate of sea-level rise in the absence of a significant source of mineral sediment. Application of k2 to a mineral sediment load typical of East and eastern Gulf Coast estuaries gives a vertical accretion rate from inorganic sediment of 0.2 cm yr-1. Total steady state accretion is the sum of the parts and therefore should not be greater than 0.5 cm yr-1 under the assumptions of the model. Accretion rates could deviate from this value depending on variation in plant productivity, root:shoot ratio, suspended sedim
40 CFR 35.4110 - What does EPA do once it receives the first LOI from a group?
Code of Federal Regulations, 2010 CFR
2010-07-01
... 40 Protection of Environment 1 2010-07-01 2010-07-01 false What does EPA do once it receives the... to Apply for A Tag § 35.4110 What does EPA do once it receives the first LOI from a group? The following table shows what EPA does when it receives the first LOI from a group: If your site . . . Then EPA...
Burn Delay Analysis of the Lunar Orbit Insertion for Korea Pathfinder Lunar Orbiter
NASA Astrophysics Data System (ADS)
Bae, Jonghee; Song, Young-Joo; Kim, Young-Rok; Kim, Bangyeop
2017-12-01
The first Korea lunar orbiter, Korea Pathfinder Lunar Orbiter (KPLO), has been in development since 2016. After launch, the KPLO will execute several maneuvers to enter into the lunar mission orbit, and will then perform lunar science missions for one year. Among these maneuvers, the lunar orbit insertion (LOI) is the most critical maneuver because the KPLO will experience an extreme velocity change in the presence of the Moon’s gravitational pull. However, the lunar orbiter may have a delayed LOI burn during operation due to hardware limitations and telemetry delays. This delayed burn could occur in different captured lunar orbits; in the worst case, the KPLO could fly away from the Moon. Therefore, in this study, the burn delay for the first LOI maneuver is analyzed to successfully enter the desired lunar orbit. Numerical simulations are performed to evaluate the difference between the desired and delayed lunar orbits due to a burn delay in the LOI maneuver. Based on this analysis, critical factors in the LOI maneuver, the periselene altitude and orbit period, are significantly changed and an additional delta-V in the second LOI maneuver is required as the delay burn interval increases to 10 min from the planned maneuver epoch.
Preparation of durable flame retardant PAN fabrics based on amidoximation and phosphorylation
NASA Astrophysics Data System (ADS)
Zhang, Yue; Ren, Yuanlin; Liu, Xiaohui; Huo, Tongguo; Qin, Yiwen
2018-01-01
This paper aims to develop a method to impart polyacrylonitrile (PAN) fabric durable flame retadancy. PAN fabric was modified with hydroxylamine hydrochloride (HA) to prepare amidoxime PAN fabric (A-PAN) followed by phosphorylation with phosphoric acid (PA) to obtain flame retardant PAN fabric (P-A-PAN). Thermogravimetric (TG) analysis, differential scanning calorimetry (DSC), microscale combustion calorimetry (MCC) and pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS) were used to analyze the thermal degradation process and flame retardant mechanisms. The structure of the fabrics was characterized by Fourier transform infrared spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS). The surface morphology of fabrics was observed by scanning electron microscope (SEM). Moreover, the flame retardancy of fabrics before and after washing was evaluated by Limiting oxygen index (LOI) and horizontal burning test. The results showed that the P-A-PAN possessed an excellent thermal stability with the highest LOI value of 34.1% and the highest char residue of 55.67% at 800 °C. Most importantly, the P-A-PAN possessed a wonderful flame retardant durability with a little decrease of LOI after 20 washing cycles. When they were ignited, the P-A-PAN fabrics before and after washing were both nonflammable due to the char residue formation of modified fabric.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Carlson, Gary
This final report provides a complete summary of the activities, results, analytical discussion, and overall evaluation of the project titled “Economical and Environmentally Benign Extraction of Rare Earth Elements (REES) from Coal & Coal Byproducts” under DOE Award Number DE-FE-0027155 that started in March 2016 and ended December 2017. Fly ash was selected as the coal-byproduct source material due to fact that it is readily available with no need for extensive methods to obtain the material, it is produced in large quantities (>50 million tons per year) and had REE concentrations similar to other coal-byproducts. The selected fly ash usedmore » throughout this project was from the Mill Creek power generating facility operated by Louisville Gas and Electric located in Louisville, KY and was subjected to a variety of physical and chemical characterization tests. Results from fusion extractions showed that the selected fly-ash had a TREE+Y concentration of 480 ppm with critical REEs concentration of 200 ppm. The fly ash had an outlook ratio of 1.25 and an estimated value of $16-$18 worth of salable REEs per 1-tonne of fly ash. Additional characterizations by optical evaluation, QEMSCAN, XRD, size fractionation, and SEM analysis showed the fly ash consisted of small glassy spherules with a size range between 1 to 110 µm (ave. diam. of 13 um), was heterogeneous in chemical composition (main crystalline phases: aluminum oxides and iron oxides) and was primarily an amorphous material (75 to 80%). A simple stepped approach was completed to estimate the total REE resource quantity. The approach included REE characterization of the representative samples, evaluation of fly-ash availability, and final determination estimated resource availability with regards to REE grade on a regional and national scale. This data represents the best available information and is based upon the assumptions that the power generating facility where the fly-ash was obtained will use the same coal sources (actual mines were identified), the coal materials will have relatively consistent REE concentrations, and the REE extraction process developed during this project can achieve 42% REE recovery (validated and confirmed). Calculations indicated that the estimated REE resource is approximately 175,000 tonnes with a current estimated value of $3,330MM. The proposed REE extraction and production process developed during this project used four fundamental steps; 1) fly-ash pretreatment to enhance REE extraction, 2) REE extraction by acid digestion, 3) REE separation/concentration by carbon adsorption and column chromatography, and 4) REE oxide production. Secondary processing steps to manage process residuals and additional processing techniques to produce value-added products were incorporated into the process during the project. These secondary steps were not only necessary to manage residuals, but also provided additional revenue streams that offset operational and capital expenditures. The process produces one value product stream (production of zeolite Na-P1), a solids waste stream, and one liquid stream that met RCRA discharge requirements. Based upon final design criteria and operational parameters, the proposed system could produce approximately 200 grams of REOs from 1-tonne of fly-ash, thereby representing a TREE+Y recovery of 42% (project target of > 25%). A detailed economic model was developed to evaluate both CAPEX and OPEX estimates for systems with varying capacities between 100 kg to 200 tonnes of fly ash processed per day. Using a standard system capacity of 10 tonne/day system, capital costs were estimated at $88/kg fly ash while operating costs were estimated at approximately $450/kg fly ash. This operating cost estimate includes a revenue of $495/tonne of fly ash processed from the value-added product produced from the system (zeolite Na-P1). Although operating cost savings due to zeolite production were significant, the capital + operating cost for a 10 tonne system was more expensive than the total dollar value of REEs present in the fly ash material. Specifically, the estimated cost per 1-tonne of fly ash treated is approximately $540 while the estimated value of REEs in the fly ash is $18-$20/tonne. This is an excessive difference showing that the proposed process is not economically feasible strictly on the basis of REE revenue compared to extraction costs. Although the current proposed system does not produce sufficient quantities of REEs or additional revenue sources to offset operational and capital costs, supplementary factors including US strategic concerns, commercial demands, and defense department requirements must be factored. At this time, the process developed during this project provides foundational information for future development of simple processes that require low capital investment and one that will extract a valuable quality and quantity of REE oxides from industrial waste.« less
Regenerable cement sorbent for recycle fluidized-bed combustion systems. Final report
DOE Office of Scientific and Technical Information (OSTI.GOV)
Yoo, H.J.; Steinberg, M.
1985-04-01
Agglomerated cement sorbent pellets (ACS) were investigated as a regenerable sorbent for the purpose of removing SO/sub 2/ in a circulating fluidized-bed combustion (CFBC) system. The systems concept is to use an intermediate size sorbent pellet so that fine flyash can be separated from the sorbent at the top end of the CFBC and the coarse gangue can be separated from the sorbent remaining in the bottom end. In this study, basic experimental data were obtained on the sulfur capture capacity and regenerability of the ACS pellets as a function of the concentration of flyash mixed with the pellets andmore » as a function of temperature. Thermogravimetric Analysis (TGA) was used for this purpose. A 40 mm bench-scale fluidized-bed unit operated with a simulated combustion gas mixture was used to determine the attrition resistance of the pellets. The results indicate that 30-100 mesh ACS pellets at 958/sup 0/C (1756/sup 0/F) maintain a 55-60% sulfation capacity mixed with coal flyash concentration up to 75% by weight. The sorbent pellets were 100% regenerable and did not lose reactivity in repeated cyclical sulfation and regeneration tests. At higher temperatures up to 1158/sup 0/C (2116/sup 0/F) reactivity towards SO/sub 2/ declines due to sintering of the flyash on the surface of the ACS pellets. Tests showed good attrition resistance with only 1% loss per cycle in cyclical operation. These initial basic results indicate that ACS pellets are potentially useful as a recoverable and regenerable high capacity SO/sub 2/ sorbent in a circulating fluidized-bed combustion system. 5 refs., 7 figs., 8 tabs.« less
Pretreatment of Oil Palm Frond (OPF) with Ionic Liquid
NASA Astrophysics Data System (ADS)
Azmi, I. S.; Azizan, A.; Salleh, R. Mohd
2018-05-01
Pretreatment is the key to unlock the recalcitrance of lignocellulose for cellulosic biofuel production. Increasing attention has been drawn to ionic liquids (ILs) for pretreatment of lignocellulosic biomass because this approach was considered as a green engineering method over other conventional methods. In this work, Oil palm frond (OPF) was pretreated by using the ionic liquid 1-ethyl-3-methylimidazolium acetate [EMIM] Ac at the temperature of 99˚C for 3 hours. The characterization of the untreated and pretreated OPF was conducted by using different techniques which are Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The pretreatment of OPF with [EMIM] Ac was demonstrated to be effective evidenced by the significant reduction of Lateral Order Index (LOI) from FTIR, reduction of Crystallinity Index (CI) based on XRD and the significant morphology changes indicated by SEM. The CI value for the pretreated OPF decreased from 0.47 (untreated sample) to 0.28 while the LOI value decreased from 1.10 to 0.24 after pretreatment with [EMIM]Ac and the SEM morphology showed that the pretreated OPF becomes distorted and disordered.
NASA Astrophysics Data System (ADS)
Woo, Jin; Song, Young-Joo; Park, Sang-Young; Kim, Hae-Dong; Sim, Eun-Sup
2010-09-01
The optimal Earth-Moon transfer trajectory considering spacecraft's visibility from the Daejeon ground station visibility at both the trans lunar injection (TLI) and lunar orbit insertion (LOI) maneuvers is designed. Both the TLI and LOI maneuvers are assumed to be impulsive thrust. As the successful execution of the TLI and LOI maneuvers are crucial factors among the various lunar mission parameters, it is necessary to design an optimal lunar transfer trajectory which guarantees the visibility from a specified ground station while executing these maneuvers. The optimal Earth-Moon transfer trajectory is simulated by modifying the Korean Lunar Mission Design Software using Impulsive high Thrust Engine (KLMDS-ITE) which is developed in previous studies. Four different mission scenarios are established and simulated to analyze the effects of the spacecraft's visibility considerations at the TLI and LOI maneuvers. As a result, it is found that the optimal Earth-Moon transfer trajectory, guaranteeing the spacecraft's visibility from Daejeon ground station at both the TLI and LOI maneuvers, can be designed with slight changes in total amount of delta-Vs. About 1% difference is observed with the optimal trajectory when none of the visibility condition is guaranteed, and about 0.04% with the visibility condition is only guaranteed at the time of TLI maneuver. The spacecraft's mass which can delivered to the Moon, when both visibility conditions are secured is shown to be about 534 kg with assumptions of KSLV-2's on-orbit mass about 2.6 tons. To minimize total mission delta-Vs, it is strongly recommended that visibility conditions at both the TLI and LOI maneuvers should be simultaneously implemented to the trajectory optimization algorithm.
NASA Astrophysics Data System (ADS)
Dalverny, O.; Capéraa, S.; Pantalé, O.; Sattouf, C.
2002-12-01
Cet article présente une méthodologie d'identification de lois constitutives et de lois de contact adaptées aux matériaux métalliques sous chargement dynamique à grande vitesse de déformation. Les essais sont effectués à partir de montages expérimentaux adaptés à un lanceur à gaz permettant d'obtenir une vitesse de projectile de l'ordre de 350m/s pour une masse totale de 30gr. Le premier essai consiste en un impact de Taylor correspondant à un chargement mécanique de type compression. Le second essai de type “extrusion conique" permet la détermination des lois de frottement à grande vitesse. La procédure générale d'identification des lois de comportement à partir d'essais dynamiques se fait au moyen d'une analyse post-mortem des échantillons et de la corrélation entre ces résultats expérimentaux et un modèle numérique des essais. Pour les deux cas précédemment cités, nous présentons la configuration optimale d'essai ainsi que les résultats obtenus à partir d'un algorithme d'optimisation de type Levenberg-Marquard.
Biofilms' contribution to organic carbon in salt marsh sediments
NASA Astrophysics Data System (ADS)
Valentine, K.; Quirk, T. E.; Mariotti, G.; Hotard, A.
2017-12-01
Coastal salt marshes are productive environments with high potential for carbon (C) accumulation. Organic C in salt marsh sediment is typically attributed to plant biomass. Recent field measurements, however, suggest that biofilms - mainly composed of benthic diatoms and their secretion - also contribute to basal C in these environments and can be important contributors to marsh productivity, C cycling, and potentially, C sequestration. The potential for biofilms to soil organic C and the influence of mineral sedimentation of biofilm-based C accumulation is unknown. We conducted controlled laboratory experiments to test (1) whether biofilms add measurable amounts of organic C to the sediment and (2) the effect of mineral sedimentation rate on the amount of biofilm-based C accumulation. Settled beds of pure bentonite mud were created in 10-cm-wide cylinders. Each cylinder was inoculated with biofilms collected from a marsh in Louisiana. A small amount of mud was added weekly for 11 weeks. Control experiments without biofilms were also performed. Biofilms were grown with a 12/12 hours cycle, with a gentle mixing of the water column that did not cause sediment resuspension, with a nutrient-rich medium that was exchanged weekly, and in the absence of metazoan grazing. At the end of the experiment, the sediment columns were analyzed for depth-integrated chl-a, loss on ignition (LOI), and total organic carbon (TOC). Chl-a values ranged from 26-113 mg/cm2, LOI values ranged from 86-456 g/m2/yr, and TOC values ranged from 31-211 g/m2/yr. All three of these metrics (chl-a, LOI, and TOC) increased with the rate of mineral sedimentation. These results show that biofilms, in the absence of erosion and grazing, can significantly contribute to C accumulation in salt marshes, especially with high rates of mineral sedimentation. Given the short time scale of the experiment, the increase in organic C accumulation with the rate of sedimentation is attributed to stimulated biofilm production rather than increased C preservation.
Barber, Donald C.; Callaway, John C.; Chambers, Randy; Hagen, Scott C.; Hopkinson, Charles S.; Johnson, Beverly J.; Megonigal, Patrick; Neubauer, Scott C.; Troxler, Tiffany; Wigand, Cathleen
2016-01-01
Abstract A mixing model derived from first principles describes the bulk density (BD) of intertidal wetland sediments as a function of loss on ignition (LOI). The model assumes that the bulk volume of sediment equates to the sum of self‐packing volumes of organic and mineral components or BD = 1/[LOI/k1 + (1‐LOI)/k2], where k1 and k2 are the self‐packing densities of the pure organic and inorganic components, respectively. The model explained 78% of the variability in total BD when fitted to 5075 measurements drawn from 33 wetlands distributed around the conterminous United States. The values of k1 and k2 were estimated to be 0.085 ± 0.0007 g cm−3 and 1.99 ± 0.028 g cm−3, respectively. Based on the fitted organic density (k1) and constrained by primary production, the model suggests that the maximum steady state accretion arising from the sequestration of refractory organic matter is ≤ 0.3 cm yr−1. Thus, tidal peatlands are unlikely to indefinitely survive a higher rate of sea‐level rise in the absence of a significant source of mineral sediment. Application of k2 to a mineral sediment load typical of East and eastern Gulf Coast estuaries gives a vertical accretion rate from inorganic sediment of 0.2 cm yr−1. Total steady state accretion is the sum of the parts and therefore should not be greater than 0.5 cm yr−1 under the assumptions of the model. Accretion rates could deviate from this value depending on variation in plant productivity, root:shoot ratio, suspended sediment concentration, sediment‐capture efficiency, and episodic events. PMID:27819012
NASA Technical Reports Server (NTRS)
Ziese, James M.
1992-01-01
A design tool of figure of merit was developed that allows the operability of a propulsion system design to be measured. This Launch Operations Index (LOI) relates Operations Efficiency to System Complexity. The figure of Merit can be used by conceptual designers to compare different propulsion system designs based on their impact on launch operations. The LOI will improve the design process by making sure direct launch operations experience is a necessary feedback to the design process.
Berian, Julia R; Mohanty, Sanjay; Ko, Clifford Y; Rosenthal, Ronnie A; Robinson, Thomas N
2016-09-21
Older adults are at increased risk for adverse events after surgical procedures. Loss of independence (LOI), defined as a decline in function or mobility, increased care needs at home, or discharge to a nonhome destination, is an important patient-centered outcome measure. To evaluate LOI among older adult patients after surgical procedures and examine the association of LOI with readmission and death after discharge in this population. This retrospective cohort study examined 9972 patients 65 years and older with known baseline function, mobility, and living situation undergoing inpatient operations from January 2014 to December 2014 at 26 hospitals participating in the American College of Surgeons National Surgical Quality Improvement Program Geriatric Surgery Pilot Project. A total of 4895 patients were excluded because they were totally dependent, classified as class 5 by the American Society of Anesthesiologists, undergoing orthopedic or spinal procedures, or died prior to discharge. Loss of independence at time of discharge. Readmission and death after discharge. Of the 5077 patients included in this study, 2736 (53.9%) were female and 3876 (76.3%) were white, with a mean (SD) age of 75 (7) years. For this cohort, LOI increased with age; LOI occurred in 1386 of 2780 patients (49.9%) aged 65 to 74 years, 1162 of 1726 (67.3%) aged 75 to 84 years, and 479 of 571 (83.9%) 85 years and older (P < .001). Readmission occurred in 517 patients (10.2%). In a risk-adjusted model, LOI was strongly associated with readmission (odds ratio, 1.7; 95% CI, 1.4-2.2) and postoperative complication (odds ratio, 6.7; 95% CI, 4.9-9.0). Death after discharge occurred in 69 patients (1.4%). After risk adjustment, LOI was the strongest factor associated with death after discharge (odds ratio, 6.7; 95% CI, 2.4-19.3). Postoperative complication was not significantly associated with death after discharge. Loss of independence, a patient-centered outcome, was associated with postoperative readmissions and death after discharge. Loss of independence can feasibly be collected across multiple hospitals in a national registry. Clinical initiatives to minimize LOI will be important for improving surgical care for older adults.
Mu, Yue; Saffarzadeh, Amirhomayoun; Shimaoka, Takayuki
2017-01-01
This research focused on the mineral phase transformation under varied ignition conditions with the objective of estimating loss-on-ignition (LOI) parameter in municipal solid waste incineration (MSWI) fly ash residues. LOI is commonly used to measure the volatile species, unburned carbon and moisture in the solid materials. There are criteria for LOI measurement in some research fields, while there is no standard protocol for LOI measurement in MSWI fly ash. Using thermogravimetry technique, the ignition condition candidates were proposed at 440/700/900°C for 1 and 2h. Based on X-ray diffractometry results, obvious mineral phase transformation occurred as a function of ignition temperature variation rather than ignition time. Until 440°C, only some minor phases disappeared comparing with the original state. Significant mineral phase transformations of major phases (Ca- and Cl-based minerals) occurred between 440 and 700°C. The mineral phase transformation and the occurrence of newly-formed phases were determined not only by the ignition condition but also by the content of the co-existing components. Mineral phase components rarely changed when ignition temperature rose from 700 to 900°C. Consequently, in order to prevent critical damages to the original mineralogical composition of fly ash, the lowest ignition temperature (440°C) for 2h was suggested as an ideal measurement condition of LOI in MSWI fly ash. Copyright © 2016 Elsevier Ltd. All rights reserved.
Influence of heating on the weight loss and mineral phase in MSWI ash: LOI of incineration ash
NASA Astrophysics Data System (ADS)
Yang, Shuo
2017-04-01
Loss on ignition (LOI) is a very common method for estimating the volatile species in solid sample. Normally, the measurement of LOI can be convenient and accurate, but for municipal solid waste incineration (MSWI) ash, the process may become intricate due to the complexity of the sample. In the incineration ash, there exist various phases, such as mineral, metal, organic and glass. The reaction and transformation of some materials during heating will influence the measurement. 5 incineration ash samples were selected and tested in this study. LOI content was basically measured at high (850°C) and relatively low (440°C) temperatures. The comparison between these two measurements showed a large difference. X-ray diffraction (XRD) and thermal analysis (TG-DTA) were carried out to investigate the mineral changes and weight losses with different ignition temperatures. The mineralogical analysis suggests that the decomposition of hydrate and carbonate phases cannot be neglected for LOI measurement of incineration. A long-time heating under relatively lower temperature (400∼450°C) compared with soil sample measurement (≥500°C) was recommended by this study.
GRAIL TCM-5 Go/No-Go: Developing Lunar Orbit Insertion (LOI) Criteria
NASA Technical Reports Server (NTRS)
Chung, Min-Kun J.
2013-01-01
The Gravity Recovery and Interior Laboratory (GRAIL) mission successfully completed mapping the Moon's gravity field to an unprecedented level for a better understanding of the internal structure and thermal evolution of the Moon. The mission success was critically dependent on the success of the Lunar Orbit Insertion (LOI). In this paper we establish a set of LOI criteria to meet all the requirements and we use these criteria to establish Go/No-Go boundaries of the last, statistical Trajectory Correction Maneuvers (TCM-5s) for operations.
Fukuzawa, R; Anaka, M R; Heathcott, R W; McNoe, L A; Morison, I M; Perlman, E J; Reeve, A E
2008-08-01
Current models of Wilms tumour development propose that histological features of the tumours are programmed by the underlying molecular aberrations. For example, tumours associated with WT1 mutations arise from intralobar nephrogenic rests (ILNR), concur with CTNNB1 mutations and have distinct histology, whereas tumours with IGF2 loss of imprinting (LOI) often arise from perilobar nephrogenic rests (PLNR). Intriguingly, ILNR and PLNR are found simultaneously in Wilms tumours in children with overgrowth who have constitutional IGF2 LOI. We therefore examined whether the precursor lesions or early epigenetic changes are the primary determinant of Wilms tumour histology. We examined the histological features and gene expression profiles of IGF2 LOI tumours and WT1-mutant tumours which are associated with PLNR and/or ILNR. Two distinct types of IGF2 LOI tumours were identified: the first type had a blastemal-predominant histology associated with PLNR, while the second subtype had a myogenic histology, increased expression of mesenchymal lineage genes and an association with ILNR, similar to WT1-mutant tumours. These ILNR-associated IGF2 LOI tumours also showed signatures of activation of the WNT signalling pathway: differential expression of beta-catenin targets (MMP2, RARG, DKK1) and WNT antagonist genes (DKK1, WIF1, SFRP4). Unexpectedly, the majority of these tumours had CTNNB1 mutations, which are normally only seen in WT1-mutant tumours. The absence of WT1 mutations in tumours with IGF2 LOI indicated that CTNNB1 mutations occur predominantly in tumours arising from ILNR independent of the presence or absence of WT1 mutations. Thus, even though these two classes of tumours with IGF2 LOI have the same underlying predisposing epigenetic error, the tumour histology and the gene expression profiles are determined by the nature of the precursor cells within the nephrogenic rests and subsequent CTNNB1 mutations. Copyright (c) 2008 Pathological Society of Great Britain and Ireland. Published by John Wiley & Sons, Ltd.
The role of fly-ash particulate material and oxide catalysts in stone degradation
NASA Astrophysics Data System (ADS)
Hutchinson, A. J.; Johnson, J. B.; Thompson, G. E.; Wood, G. C.; Sage, P. W.; Cooke, M. J.
Studies of fly-ash composition identified the presence of calcium and sulphur, indicating their potential role as sources of calcium sulphate. Residual acidity (particularly for oil fly ash) suggested the possibility of enhanced chemical reaction, and the presence of transition metals, probably as oxides, might accelerate the oxidation of SO 2 to SO 42-. Exposure tests in a laboratory-based rig simulating dry deposition on Portland and Monks Park limestone, either seeded or unseeded with fly-ash particulate material or transition metal oxide catalysts, were carried out using an SO 2-containing environment at 95% r.h. Enhanced sulphation of these seeded limestones due to the above factors was minimal; at high loadings of fly ash, there was even evidence of masking the limestone surface, reducing sulphation. However, pure CaCO 3 powder in the exposure rig showed increases in sulphation when seeded with metal oxide catalysts. Thus the limestones examined contained sufficient inherent catalysts for the oxidation of SO 2 to SO 42- to proceed at such a rate that external catalysts were superfluous. This implies that dissolution rate of SO 2 in moisture films controls the availability of species for reaction with these carbonate-based stones and that fly ash deposited from the atmosphere does not enhance the reaction.
NASA Technical Reports Server (NTRS)
Genova, Anthony L.; Loucks, Michael; Carrico, John
2014-01-01
The purpose of this extended abstract is to present results from a failed lunar-orbit insertion (LOI) maneuver contingency analysis for the Lunar Atmosphere Dust Environment Explorer (LADEE) mission, managed and operated by NASA Ames Research Center in Moffett Field, CA. The LADEE spacecrafts nominal trajectory implemented multiple sub-lunar phasing orbits centered at Earth before eventually reaching the Moon (Fig. 1) where a critical LOI maneuver was to be performed [1,2,3]. If this LOI was missed, the LADEE spacecraft would be on an Earth-escape trajectory, bound for heliocentric space. Although a partial mission recovery is possible from a heliocentric orbit (to be discussed in the full paper), it was found that an escape-prevention maneuver could be performed several days after a hypothetical LOI-miss, allowing a return to the desired science orbit around the Moon without leaving the Earths sphere-of-influence (SOI).
NASA Astrophysics Data System (ADS)
Zhang, Bin; Jiang, Yujie; Han, Jian
2017-12-01
The core-double-shell microcapsules flame retardant has been regarded as a promising additive for improving the fire safety of PVC. In this article, melamine-formaldehyde resin (MF)/silicon dioxide (SiO2)/zinc hydroxystannate (ZHS) microcapsule was prepared. The effect of synthetic parameters (such as pH, agitation speed, reaction time and reaction temperature) on the morphologies and sizes of the SiO2/ZHS microcapsules were investigated in details. MF/SiO2/ZHS microcapsule was introduced into PVC to prepare biofunctional composites with excellent fire resistance and smoke suppression. The flammability of PVC composites was characterized by limiting oxygen index (LOI), smoke density (SDR), cone calorimeter test. The results showed that the sample containing 16.4% MF/SiO2/ZHS microcapsule (the mass ratio of MF:SiO2:ZHS = 2.5:2:8) achieved the maximal LOI value of 35.6%, minimal SDR value of 21.2%, and significantly decreased the peak heat release rate from 179.7 kW/m2 of neat PVC to 108.3 kW/m2. The thermal behaviors of PVC composites and the morphologies of residues were characterized.
NASA Astrophysics Data System (ADS)
Samanta, Ashis Kumar; Bagchi, Arindam
2017-06-01
Treatment with sodium stannate followed by treatment with boric acid imparts jute fabric wash fast fire resistance property as indicated by its Limiting Oxygen Index (LOI) value and 45° inclined flammability test results. The treatment was carried out by impregnation of sodium stannate followed by impregnation with an aqueous solution of boric acid and drying. Application of sodium stannate (20%) and boric acid (20%) treatment on jute fabric showed balanced flame retardancy property (LOI value 34) with some loss in fabric tenacity (loss of tenacity is 14.5%). Treated fabric retained good fire retardant property after three consecutive washing. Treated fabric also possessed good rot resistance property as indicated by soil burial test and strength retention after 21 days soil burial was found to be 65%. It is found that of sodium stannate and boric acid combination by double bath process form a synergistic durable fire-retardant as well as rot resistant when impregnated on jute material, which is considerably greater than the use of either sodium stannate or boric acid alone. TGA, FTIR and SEM analysis are also reported to support the results and reaction mechanism.
Bringing a Book to Life: An Interview with Lois Lowry.
ERIC Educational Resources Information Center
Elleman, Barbara
1998-01-01
Presents an interview with award-winning children's author Lois Lowry, who reflects upon her career as a writer and shares insights about some of her favorite characters, including Anastasia. Considers also the many controversies that have surrounded "The Giver." (SR)
ERIC Educational Resources Information Center
Canadian Human Rights Commission, Ottawa (Ontario).
This booklet presents administrative criteria for implementation of the Canadian Human Rights Act to be used by the Canadian Human Rights Commission to evaluate employment decisions affecting physically handicapped individuals. They are of value to employers who need to know how the Commission will analyze employer arguments that they have not…
U.S. Navy Marine Climatic Atlas of the World. Volume 6. Arctic Ocean
1963-02-01
commonly used trade ch or closely parallel coastlines. difTerences will be noted between isopleth values graphs in the same area. Most discrepancies...95% H»«fil range e 1,500 Uf. otd ihe M% 84% range e 1,000 ( etf ) Mean and langei a’ height are omrtled «hen data loi o level OfB mining at
NASA Astrophysics Data System (ADS)
Cao, R.; Deng, Z. L.; Ma, Y. H.; Chen, X. L.
2017-06-01
In this work, ethylene vinyl acetate (EVA) is introduced to improve the properties of high-density polyethylene (HDPE)/magnesium hydroxide (MH) composites. The thermal stability, flame retardancy and mechanical properties of HDPE/EVA/MH composites are investigated and discussed. With increasing content of EVA, the limiting oxygen index (LOI) of the composites increases. The thermal stability analysis shows that the initial decomposition temperature begins at a low temperature; however, the residues of the composites at 600°C increase when HDPE is replaced by small amounts of EVA. The early degradation absorbs heat, dilute oxygen and residue. During this process, it protects the matrix inside. Compared with the HDPE/MH and EVA/MH composites, the ternary HDPE/EVA/MH composites exhibit better flame retardancy by increasing the LOI values, and reducing the heat release rate (HRR) and total heat release (THR). With increasing content of EVA, the mechanical properties can also be improved, which is attributed to the good affinity between EVA and MH particles.
NASA Astrophysics Data System (ADS)
Zhang, Weizhou; Ren, Jiawei; Wei, Ting; Guo, Weihong
2018-02-01
In this paper, the synergistic effect of ammonium polyphosphate (APP) and expandable graphite (EG) on flame-retarded poly(butylene terephthalate) (PBT) was systermically investigated using limiting oxygen index (LOI), UL-94 testing, microscale combustion calorimetry (MCC), thermal-gravimetric analysis (TGA) and scanning electronic microscopy (SEM). PBT composites containing 20 wt% of APP: EG (1:3) combinations exhibits a high LOI value of 29.8 and reaches V-0 rating in UL-94 testing, indicating that the flame retardant property is greatly enhanced compared to the composites solely with APP or EG. SEM images show that the combination of APP and EG could promote the formation of a compact char layer. The compact char layer protects the PBT resin efficiently by preventing penetration of heat flux inside the matrix and retards the decomposition of PBT, consequently improves the thermal stability of PBT materials as revealed by TGA. All of the results demonstrate that APP and EG are high efficiency synergists for improving the flame retardation of PBT materials.
Nason, Peter; Johnson, Raymond H; Neuschütz, Clara; Alakangas, Lena; Öhlander, Björn
2014-02-28
Novel solutions for sulfide-mine tailings remediation were evaluated in field-scale experiments on a former tailings repository in northern Sweden. Uncovered sulfide-tailings were compared to sewage-sludge biosolid amended tailings over 2 years. An application of a 0.2m single-layer sewage-sludge amendment was unsuccessful at preventing oxygen ingress to underlying tailings. It merely slowed the sulfide-oxidation rate by 20%. In addition, sludge-derived metals (Cu, Ni, Fe, and Zn) migrated and precipitated at the tailings-to-sludge interface. By using an additional 0.6m thick fly-ash sealing layer underlying the sewage sludge layer, a solution to mitigate oxygen transport to the underlying tailings and minimize sulfide-oxidation was found. The fly-ash acted as a hardened physical barrier that prevented oxygen diffusion and provided a trap for sludge-borne metals. Nevertheless, the biosolid application hampered the application, despite the advances in the effectiveness of the fly-ash layer, as sludge-borne nitrate leached through the cover system into the underlying tailings, oxidizing pyrite. This created a 0.3m deep oxidized zone in 6-years. This study highlights that using sewage sludge in unconventional cover systems is not always a practical solution for the remediation of sulfide-bearing mine tailings to mitigate against sulfide weathering and acid rock drainage formation. Copyright © 2014 Elsevier B.V. All rights reserved.
Nason, Peter; Johnson, Raymond H.; Neuschutz, Clara; Alakangas, Lena; Ohlander, Bjorn
2014-01-01
Novel solutions for sulfide-mine tailings remediation were evaluated in field-scale experiments on a former tailings repository in northern Sweden. Uncovered sulfide-tailings were compared to sewage-sludge biosolid amended tailings over 2 years. An application of a 0.2 m single-layer sewage-sludge amendment was unsuccessful at preventing oxygen ingress to underlying tailings. It merely slowed the sulfide-oxidation rate by 20%. In addition, sludge-derived metals (Cu, Ni, Fe, and Zn) migrated and precipitated at the tailings-to-sludge interface. By using an additional 0.6 m thick fly-ash sealing layer underlying the sewage sludge layer, a solution to mitigate oxygen transport to the underlying tailings and minimize sulfide-oxidation was found. The fly-ash acted as a hardened physical barrier that prevented oxygen diffusion and provided a trap for sludge-borne metals. Nevertheless, the biosolid application hampered the application, despite the advances in the effectiveness of the fly-ash layer, as sludge-borne nitrate leached through the cover system into the underlying tailings, oxidizing pyrite. This created a 0.3 m deep oxidized zone in 6-years. This study highlights that using sewage sludge in unconventional cover systems is not always a practical solution for the remediation of sulfide-bearing mine tailings to mitigate against sulfide weathering and acid rock drainage formation.
Khan, Shadab Ali; Uddin, Imran; Moeez, Sana; Ahmad, Absar
2014-01-01
In this paper, we for the first time show the ability of the mesophilic fungus Fusarium oxysporum in the bioleaching of waste material such as Fly-ash for the extracellular production of highly crystalline and highly stable, protein capped, fluorescent and water soluble silica nanoparticles at ambient conditions. When the fungus Fusarium oxysporum is exposed to Fly-ash, it is capable of selectively leaching out silica nanoparticles of quasi-spherical morphology within 24 h of reaction. These silica nanoparticles have been completely characterized by UV-vis spectroscopy, Photoluminescence (PL), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Energy dispersive analysis of X-rays (EDAX). PMID:25244567
Wang, Na; Zhang, Miao; Kang, Ping; Zhang, Jing; Fang, Qinghong; Li, Wenda
2018-06-13
Aiming to improve the flame retardancy performance of natural rubber (NR), we developed a novel flame retardant synergistic agent through grafting of MCM-41 to graphene oxide (GO), named as GO-NH-MCM-41, as an assistant to intumescent flame retardants (IFR). The flame retardancy of NR/IFR/GO-NH-MCM-41 composites was evaluated by limited oxygen index (LOI), UL-94, and cone calorimeter test. The LOI value of NR/IFR/GO-NH-MCM-41 reached 26.3%; the UL-94 ratings improved to a V-0 rating. Moreover, the addition of GO-NH-MCM-41 decreased the peak heat release rate (PHRR) and the total heat release (THR) of the natural rubber composites. Furthermore, the addition of GO-NH-MCM-41 increased the thickness of char residue. The images of SEM indicated the char residue was more compact and continuous. The degradation of GO-NH-MCM-41-based NR composites was completed with a mass loss of 35.57% at 600 °C. The tensile strength and the elongation at break of the NR/IFR/GO-NH-MCM-41 composites were 13.9 MPa and 496.7%, respectively. The results of the rubber process analyzer (RPA) reached the maximum value, probably due to a better network of fillers in the matrix.
Tripti; Kumar, Adarsh; Usmani, Zeba; Kumar, Vipin; Anshumali
2017-04-01
Overuse of agrochemical fertilizers alarmingly causes deterioration in soil health and soil-flora. Persistence of these agrochemicals exerts detrimental effects on environment, potentially inducing toxic effects on human health, thus pronouncing an urgent need for a safer substitute. The present study investigates the potential use of agricultural and industrial wastes as carrier materials, viz. biochar and flyash, respectively, for preparation of bioformulations (or biofertilizers) using two plant growth promoting rhizobacteria, Bacillus sp. strain A30 and Burkholderia sp. strain L2, and its effect on growth of Lycopersicon esculentum Mill. (tomato). The viability of strains was determined based on colony forming units (cfu) count of each bioformulation at an interval of 60 days for a period of 240 days. Seeds were coated with different carrier based bioformulations and pot experiment(s) were carried out to access its effects on plant growth parameters. Biochar based bioformulations showed higher cfu count and maximum viability for strain L2 (10 7 cfu g -1 ) at 240 days of storage. Maximum percentage of seed germination was also observed in biochar inoculated with strain L2. Significant (p < 0.05) increase in plant growth parameters (dry and fresh biomass, length, number of flowers) were ascertained from the pot experiment and amongst all bioformulations, biochar inoculated with strain L2 performed consistently thriving results for tomato yield. Furthermore, post-harvest study of this bioformulation treated soil improved physico-chemical properties and dehydrogenase activity as compared to pre-plantation soil status. Overall, we show that prepared biochar based bioformulation using Burkholderia sp. L2 as inoculum can tremendously enhance the productivity of tomato, soil fertility, and can also act as a sustainable substitute for chemical fertilizers. In addition, mixture of biochar and flyash inoculated with strain L2 also showed noteworthy results for the growth parameters and yield, and future studies are required to strengthen flyash utilization as carrier materials to resolve its disposal problem and waste management. Copyright © 2016 Elsevier Ltd. All rights reserved.
40 CFR Appendix A to Subpart Nnn... - Method for the Determination of LOI
Code of Federal Regulations, 2011 CFR
2011-07-01
... The purpose of this test is to determine the LOI of cured blanket insulation. The method is applicable... designed to heat to at least 540 °C (1,000 °F) and controllable to ±10 °C (50 °F). 2.3Wire tray for holding...
40 CFR Appendix A to Subpart Nnn... - Method for the Determination of LOI
Code of Federal Regulations, 2010 CFR
2010-07-01
... The purpose of this test is to determine the LOI of cured blanket insulation. The method is applicable... designed to heat to at least 540 °C (1,000 °F) and controllable to ±10 °C (50 °F). 2.3Wire tray for holding...
40 CFR Appendix A to Subpart Nnn... - Method for the Determination of LOI
Code of Federal Regulations, 2012 CFR
2012-07-01
... The purpose of this test is to determine the LOI of cured blanket insulation. The method is applicable... designed to heat to at least 540 °C (1,000 °F) and controllable to ±10 °C (50 °F). 2.3Wire tray for holding...
75 FR 80041 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2010-12-21
...: The Gulf of Mexico Fishery Management Council will convene a public meeting of the Outreach and... be held at the Gulf of Mexico Fishery Management Council, 2203 N. Lois Avenue, Suite 1100, Tampa, FL 33607. Council address: Gulf of Mexico Fishery Management Council, 2203 N. Lois Avenue, Suite 1100...
Project Management Done Here: Lois Langer--Thompson Hennepin County Library, MN
ERIC Educational Resources Information Center
Library Journal, 2004
2004-01-01
How do you simultaneously renovate a grocery store into a state-of-the-art resource library, supervise the daily operations of five libraries, lead a team in reimagining reference service, and plan your wedding? Ask Lois Langer, coordinating librarian of Hennepin County Library. Her answer: "Project management--you can do anything,…
NASA Technical Reports Server (NTRS)
Garn, Michelle; Qu, Min; Chrone, Jonathan; Su, Philip; Karlgaard, Chris
2008-01-01
Lunar orbit insertion LOI is a critical maneuver for any mission going to the Moon. Optimizing the geometry of this maneuver is crucial to the success of the architecture designed to return humans to the Moon. LOI burns necessary to meet current NASA Exploration Constellation architecture requirements for the lunar sortie missions are driven mainly by the requirement for global access and "anytime" return from the lunar surface. This paper begins by describing the Earth-Moon geometry which creates the worst case (delta)V for both the LOI and the translunar injection (TLI) maneuvers over the full metonic cycle. The trajectory which optimizes the overall (delta)V performance of the mission is identified, trade studies results covering the entire lunar globe are mapped onto the contour plots, and the effects of loitering in low lunar orbit as a means of reducing the insertion (delta)V are described. Finally, the lighting conditions on the lunar surface are combined with the LOI and TLI analyses to identify geometries with ideal lighting conditions at sites of interest which minimize the mission (delta)V.
Durable flame retardant finish for silk fabric using boron hybrid silica sol
NASA Astrophysics Data System (ADS)
Zhang, Qiang-hua; Gu, Jiali; Chen, Guo-qiang; Xing, Tie-ling
2016-11-01
A hybrid silica sol was prepared via sol gel method using tetraethoxysilane (TEOS) as a precursor and boric acid (H3BO3) as flame retardant additive and then applied to silk fabric. In order to endow silk fabric with durable flame retardancy, 1,2,3,4-butanetetracarboxylic acid (BTCA) was used as cross-linking agent for the sake of strong linkage formation between the hybrid silica sol and silk fabric. The FT-IR and XPS analysis demonstrated the Si-O-B formation in the sol system, as well as the linkage between the sol and silk after the treatment. The limiting oxygen index (LOI) and smoke density test indicated good flame retardancy and smoke suppression of the treated silk fabrics. The micro calorimeter combustion (MCC) test and thermo gravimetric (TG) analysis showed that the treated samples had less weight loss in the high temperature and lower heat release rate when burning. The washing durability evaluation results indicated that there was a distinct improvement for the silk samples treated with BTCA even after 30 times washing. In addition, the influence of the processing order of BTCA and silica sol treatment on the limiting oxygen index (LOI) of the finished silk fabric was also investigated. And the results demonstrated that the sample treated with BTCA first and then with the silica sol exhibited better LOI value (32.3%) than that of the sample by the conversed treatment order. Moreover the tensile property of treated samples was nearly unchanged, but the handle of sol treated samples obviously decreased.
Talamo, Jonathan H; Gooding, Philip; Angeley, David; Culbertson, William W; Schuele, Georg; Andersen, Daniel; Marcellino, George; Essock-Burns, Emma; Batlle, Juan; Feliz, Rafael; Friedman, Neil J; Palanker, Daniel
2013-04-01
To compare 2 optical patient interface designs used for femtosecond laser-assisted cataract surgery. Optimedica Corp., Santa Clara, California, USA, and Centro Laser, Santo Domingo, Dominican Republic. Experimental and clinical studies. Laser capsulotomy was performed during cataract surgery with a curved contact lens interface (CCL) or a liquid optical immersion interface (LOI). The presence of corneal folds, incomplete capsulotomy, subconjunctival hemorrhage, and eye movement during laser treatment were analyzed using video and optical coherence tomography. The induced rise of intraocular pressure (IOP) was measured in porcine and cadaver eyes. Corneal folds were identified in 70% of the CCL cohort; 63% of these had areas of incomplete capsulotomies beneath the corneal folds. No corneal folds or incomplete capsulotomies were identified in the LOI cohort. The mean eye movement during capsulotomy creation (1.5 sec) was 50 μm with a CCL and 20 μm with an LOI. The LOI cohort had 36% less subconjunctival hemorrhage than the CCL cohort. During suction, the mean IOP rise was 32.4 mm Hg ± 3.4 (SD) in the CCL group and 17.7 ± 2.1 mm Hg in the LOI group. Curved contact interfaces create corneal folds that can lead to incomplete capsulotomy during laser cataract surgery. A liquid interface eliminated corneal folds, improved globe stability, reduced subconjunctival hemorrhage, and lowered IOP rise. Copyright © 2013 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.
Corporate Language: The Blind Spot of Language Policy? Reflections on France's Loi Toubon
ERIC Educational Resources Information Center
Saulière, Jérôme
2014-01-01
This article looks at France's Loi Toubon, which mandates the use of French in private companies, to illustrate how macro-level language planning reaches a dead end if it fails to consider local contexts and involve micro-level agents. The motivations, limitations and contradictions of France's language policy in relation to companies are…
Zanzibar's Curriculum Reform: Implications for Children's Educational Rights
ERIC Educational Resources Information Center
Babaci-Wilhite, Zehlia
2015-01-01
This article explores recent developments in linguistic choices in education in Zanzibar and examines the arguments for using local languages of instruction (LoI) as a right. The article's analysis is based on a study of a curriculum change in Zanzibar in which English replaced Kiswahili as the LoI in the last two years of primary school in…
Bio-based barium alginate film: Preparation, flame retardancy and thermal degradation behavior.
Liu, Yun; Zhang, Chuan-Jie; Zhao, Jin-Chao; Guo, Yi; Zhu, Ping; Wang, De-Yi
2016-03-30
A bio-based barium alginate film was prepared via a facile ionic exchange and casting approach. Its flammability, thermal degradation and pyrolysis behaviors, thermal degradation mechanism were studied systemically by limiting oxygen index (LOI), vertical burning (UL-94), microscale combustion calorimetry (MCC), thermogravimetric analysis (TGA) coupled with Fourier transform infrared analysis (FTIR) and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). It showed that barium alginate film had much higher LOI value (52.0%) than that of sodium alginate film (24.5%). Moreover, barium alginate film passed the UL-94 V-0 rating, while the sodium alginate film showed no classification. Importantly, peak of heat release rate (PHRR) of barium alginate film in MCC test was much lower than that of sodium alginate film, suggested that introduction of barium ion into alginate film significantly decreased release of combustible gases. TG-FTIR and Py-GC-MS results indicated that barium alginate produced much less flammable products than that of sodium alginate in whole thermal degradation procedure. Finally, a possible degradation mechanism of barium alginate had been proposed. Copyright © 2015 Elsevier Ltd. All rights reserved.
Chen, Zhiyuan; Hagen, Darren E.; Elsik, Christine G.; Ji, Tieming; Morris, Collin James; Moon, Laura Emily; Rivera, Rocío Melissa
2015-01-01
Embryos generated with the use of assisted reproductive technologies (ART) can develop overgrowth syndromes. In ruminants, the condition is referred to as large offspring syndrome (LOS) and exhibits variable phenotypic abnormalities including overgrowth, enlarged tongue, and abdominal wall defects. These characteristics recapitulate those observed in the human loss-of-imprinting (LOI) overgrowth syndrome Beckwith–Wiedemann (BWS). We have recently shown LOI at the KCNQ1 locus in LOS, the most common epimutation in BWS. Although the first case of ART-induced LOS was reported in 1995, studies have not yet determined the extent of LOI in this condition. Here, we determined allele-specific expression of imprinted genes previously identified in human and/or mouse in day ∼105 Bos taurus indicus × Bos taurus taurus F1 hybrid control and LOS fetuses using RNAseq. Our analysis allowed us to determine the monoallelic expression of 20 genes in tissues of control fetuses. LOS fetuses displayed variable LOI compared with controls. Biallelic expression of imprinted genes in LOS was associated with tissue-specific hypomethylation of the normally methylated parental allele. In addition, a positive correlation was observed between body weight and the number of biallelically expressed imprinted genes in LOS fetuses. Furthermore, not only was there loss of allele-specific expression of imprinted genes in LOS, but also differential transcript amounts of these genes between control and overgrown fetuses. In summary, we characterized previously unidentified imprinted genes in bovines and identified misregulation of imprinting at multiple loci in LOS. We concluded that LOS is a multilocus LOI syndrome, as is BWS. PMID:25825726
Chen, Zhiyuan; Hagen, Darren E; Elsik, Christine G; Ji, Tieming; Morris, Collin James; Moon, Laura Emily; Rivera, Rocío Melissa
2015-04-14
Embryos generated with the use of assisted reproductive technologies (ART) can develop overgrowth syndromes. In ruminants, the condition is referred to as large offspring syndrome (LOS) and exhibits variable phenotypic abnormalities including overgrowth, enlarged tongue, and abdominal wall defects. These characteristics recapitulate those observed in the human loss-of-imprinting (LOI) overgrowth syndrome Beckwith-Wiedemann (BWS). We have recently shown LOI at the KCNQ1 locus in LOS, the most common epimutation in BWS. Although the first case of ART-induced LOS was reported in 1995, studies have not yet determined the extent of LOI in this condition. Here, we determined allele-specific expression of imprinted genes previously identified in human and/or mouse in day ∼105 Bos taurus indicus × Bos taurus taurus F1 hybrid control and LOS fetuses using RNAseq. Our analysis allowed us to determine the monoallelic expression of 20 genes in tissues of control fetuses. LOS fetuses displayed variable LOI compared with controls. Biallelic expression of imprinted genes in LOS was associated with tissue-specific hypomethylation of the normally methylated parental allele. In addition, a positive correlation was observed between body weight and the number of biallelically expressed imprinted genes in LOS fetuses. Furthermore, not only was there loss of allele-specific expression of imprinted genes in LOS, but also differential transcript amounts of these genes between control and overgrown fetuses. In summary, we characterized previously unidentified imprinted genes in bovines and identified misregulation of imprinting at multiple loci in LOS. We concluded that LOS is a multilocus LOI syndrome, as is BWS.
The Rub between Fact and Fiction: Ideology in Lois Lenski's Regional Maps
ERIC Educational Resources Information Center
Pond, Julia
2011-01-01
From the early 1940s until the late 1960s, Lois Lenski embarked on an exploration of American regions through children's books. This body of work, which has become known as Lenski's Regional Series, began by exploring the regions Lenski herself experienced each year as she traveled from Connecticut to Florida for her health. As Lenski realized the…
The Behavior and Durability of Self-Consolidating Concrete.
DOT National Transportation Integrated Search
2015-05-01
This report focuses on the production of self-consolidating concrete using local materials from Las Vegas, Nevada. Tests were conducted on eight self-consolidating concrete mixtures having two different percentages of fly-ash replacement (25% and 35%...
Degradation of toxic contaminants in water using nanotitania on flyash substrate
NASA Astrophysics Data System (ADS)
Sharma, Richa; Madan, Shubhangi; Tiwari, Sangeeta
2018-05-01
Photocatalysis has been of significant interest due to its new technology for environmental pollution. Titanium dioxide is known to be extensively used photocatalyst for the removal of environmental contaminants. In the present work, the generation of TiO2 nanoparticles by the thermal decomposition of titanium tetraisopropoxide (TTIP) on flyash core was carried out by insitu precipitation technique. Photodegradation of methylene blue as a water pollutant was carried out experimentally using self-made laboratory photocatalytic reactor and then photocatalytic properties of prepared core shell composite are studied by using UV light. Absorbance spectra were measured at different time interval using a spectrophotometer and the concentration of the test solution was calculated. Effect of different annealing temperatures on dye degradation was studied. Composite particles annealed at 800°C showed almost 82% of removal of the dye in just 10 minutes. Our test results showed that prepared composite material is a promising material for treating wastewater.
Reliability of Multilayer Copper/Polyimide
1993-11-01
LOIS H. WALSH R eliability R esearch E ng ineer -, . .....................-------- - - Reliability Physics Branch i-1’ , ý, Ay cci~i• es "AL f, , or Dist...average of 925 hours The chamber "as operated at 85 C 10 r h All the samples showed initial dielectric constant values consistent w%,ith previous...19. Matsumoto, 0., Katagiri, T., Thin Solid Films, 146, 283 (1987) 20. Malladi , D.P., J Membrane Sci., 19, 209 (1984) 21. Schubert, P.J., Nevin, J.H
On the Goals and Outcomes of Arts Education: An interview with Lois Hetland
ERIC Educational Resources Information Center
Heller, Rafael
2017-01-01
Supporters of K-12 arts education often make the case that when students study music, dance, theatrical performance, and the visual arts, they tend to improve in the academic subjects as well. But, as Lois Hetland explains, that's not the best way to advocate for greater investments in arts instruction. In fact, a careful analysis of a vast amount…
ERIC Educational Resources Information Center
Weiner, Lois; Kaplan, Andy
2014-01-01
In this commentary, Andy Kaplan discusses with Lois Weiner, Diane Ravitch's latest book "The Reign of Error," which combines scholarly argument and scrupulous research in defense of democratic education. Weiner notes, the book will prove an important resource in the ongoing struggle for the survival of public schooling. Weiner adds,…
Contandriopoulos, D.; Hudon, Raymond; Martin, Elisabeth; Thompson, Daniel
2013-01-01
Sommaire L’objet de cet article est constitué par les processus décisionnels entourant la mise en œuvre de la Loi sur les agences de développement de réseaux locaux de services de santé et de services sociaux (Loi 25). Nous entendons mettre en lumière les stratégies des groupes ou institutions de diverses natures qui ont fait valoir leurs préférences et ont tenté, avec un succès inégal, d’influencer les décisions relatives à cette réforme majeure de la structure du système de santé québécois. Au plan théorique, nous nous appuyons principalement sur les modèles d’analyse du lobbying qui, depuis les travaux fondateurs de Milbrath (1960, 1963), présentent cette pratique comme un processus fondamental d’échange d’information. Selon les données colligées dans les retranscriptions d’entrevues, les stratégies observées correspondent effectivement aux caractéristiques constitutives du lobbying et, dans quelques situations, à celles du patronage. La combinaison de ces divers éléments révèle que la mise en œuvre de la Loi 25 s’avère être avant tout un processus proprement politique. Ainsi, furent relégués au second plan les arguments techniques qui composaient initialement les objectifs de la Loi. PMID:23509412
The Official Home Page of the U.S. Air Force
: May 24 Air Force directs one-day operational safety review SecAF LOI SecAF LOI Letter of Intent AF and members using two C-130 and one C-17 training airframes. (U.S. Air Force photo by Richard Eldridge) The Transport Team crew members using two C-130 and one C-17 training airframes. (U.S. Air Force photo by
Loss of imprinting of IGF2 and the epigenetic progenitor model of cancer
Leick, Mark B; Shoff, Christopher J; Wang, Erwin C; Congress, Jaclyn L; Gallicano, G Ian
2012-01-01
Among the hypotheses discussing cancer formation, the cancer stem cell (CSC) theory is one receiving widespread support. One version of this theory states that changes in otherwise healthy cells can cause formation of tumor- initiating cells (TICs), which have the potential to create precancerous stem cells that can lead to CSC formation. These CSCs can be rare, in contrast to their differentiated progeny, which give rise to the vast majority of the tumor mass in most cancers. Loss of imprinting (LOI) of the insulin-like growth factor-2 (IGF2) gene is one change that can produce these TICs via an epigenetic progenitor model of tumorigenesis. While IGF2 usually supports normal cellular growth, LOI of IGF2 may lead to overexpression of the gene and moreover global chromatin instability. This modification has been observed in many forms of cancer, and given the effect of LOI of IGF2 and its role in cancer, detecting a loss of imprinting in this gene could serve as a valuable diagnostic tool. Preclinical data has shown some progress in identifying therapeutic approaches seeking to exploit this relationship. Thus, further research surrounding LOI of IGF2 could lead to increased understanding of several cancer types and enhance therapies against these diseases. PMID:23671798
2014-01-01
maintained by the Criminal Justice Information Services (CJIS) section of the FBI and the Law Enforcement Online ( LEO ) system. The Regional...2013, pp. 20–26. Davis, Lois M., Michael Pollard, Kevin Ward, Jeremy M. Wilson, Danielle M. Varda, Lydia Hansell, and Paul S. Steinberg, Long-Term...default/files/2010_ITACG_Report_ Final_30Nov10.pdf Rhodes, William, Meg Chapman, Michael Shively, Christina Dyous, Dana Hunt, and Kristin Wheeler
Evaluate the Use of Mineral Admixtures in Concrete to Mitigate Alkali-Silica Reactivity.
DOT National Transportation Integrated Search
1996-12-01
The increased use of mineral admixtures in portland cement concrete demands a better understanding of their properties and effects on hardened concrete. One of several beneficial advantages of mineral admixtures like flyash and silica fume is their p...
The effectiveness of the fly-ash slurry injection method to eliminate depressed transverse cracks.
DOT National Transportation Integrated Search
2009-01-01
One of the primary causes of increasing roughness in asphalt pavements in Kansas has been naturally occurring transverse cracks. Maintenance forces continually tried to seal the cracks; however, the cracks continued to grow wider and the depressions ...
Xie, Kongliang; Gao, Aiqin; Zhang, Yongsheng
2013-10-15
Boric acid and compound containing nitrogen, 2,4,6-tri[(2-hydroxy-3-trimethyl-ammonium)propyl]-1,3,5-triazine chloride (Tri-HTAC) were used to finish cotton fabric. The flame retardant properties of the finished cotton fabrics and the synergetic effects of boron and nitrogen elements were investigated and evaluated by limited oxygen index (LOI) method. The mechanism of cross-linking reaction among cotton fiber, Tri-HTAC, and boric acid was discussed by FTIR and element analysis. The thermal stability and surface morphology of the finished cotton fabrics were investigated by thermogravimetric analysis (TGA) and scanning electron microscope (SEM), respectively. The finishing system of the mixture containing boron and nitrogen showed excellent synergistic flame retardancy for cotton fabric. The cotton fabric finished with mixture system had excellent flame retardancy. The LOI value of the treated cotton fabric increased over 27.5. Tri-HTAC could form covalent bonds with cellulose fiber and boric acid. The flame retardant cotton fabric showed a slight decrease in tensile strength and whiteness. The surface morphology of flame retardant cotton fiber was smooth. Copyright © 2013 Elsevier Ltd. All rights reserved.
Preparation and characterizations of flame retardant polyamide 66 fiber
NASA Astrophysics Data System (ADS)
Li, Y. Y.; Liu, K.; Xiao, R.
2017-06-01
The polyamide 66 (PA66) is one of the most important thermoplastic materials, but it has the drawback of flammability. So the flame retardant PA66 was prepared by condensation polymerization using nylon salt and DOPO-based flame retardant in this paper. Then the flame retardant PA66 fiber was manufactured via melt spinning. The properties of flame retardant PA66 and flame retardant PA66 fiber were investigated by relative viscosity, differential scanning calorimetry (DSC), tensile test, vertical burning test (UL94) and limiting oxygen index (LOI) test. Although the loading of the DOPO-based flame retardant decreased the molecular weight, the melting temperature, the crystallinity and the mechanical properties of flame retardant PA66, the flame retardancy properties improved. The flame retardant PA66 loaded with 5.5 wt% of DOPO-based flame retardant can achieve a UL94 V-0 rating with a LOI value of 32.9%. The tenacity at break decreased from 4.51 cN·dtex-1 for PA66 fiber to 2.82 cN·dtex-1 for flame retardant PA66 fiber which still satisfied the requirements for fabrics. The flame retardant PA66 fiber expanded the application of PA66 materials which had a broad developing prospect.
Enhanced elemental mercury removal from coal-fired flue gas by sulfur-chlorine compounds.
Yan, Nai-Qiang; Qu, Zan; Chi, Yao; Qiao, Shao-Hua; Dod, Ray L; Chang, Shih-Ger; Miller, Charles
2009-07-15
Oxidation of Hg(0) with any oxidant or converting itto a particle-bound form can facilitate its removal. Two sulfur-chlorine compounds, sulfur dichloride (SCl2) and sulfur monochloride (S2Cl2), were investigated as oxidants for Hg(0) by gas-phase reaction and by surface-involved reactions in the presence of flyash or activated carbon. The gas-phase reaction between Hg(0) and SCl2 is shown to be more rapid than the gas-phase reaction with chlorine, and the second order rate constant was 9.1 (+/- 0.5) x 10(-18) mL-molecules(-1) x s(-1) at 373 K. The presence of flyash or powdered activated carbon in flue gas can substantially accelerate the reaction. The predicted Hg(0) removal is about 90% with 5 ppm SCl2 or S2Cl2 and 40 g/m3 of flyash in flue gas. The combination of activated carbon and sulfur-chlorine compounds is an effective alternative. We estimate that coinjection of 3-5 ppm of SCl2 (or S2Cl2) with 2-3 Lb/MMacf of untreated Darco-KB is comparable in efficiency to the injection of 2-3 Lb/MMacf Darco-Hg-LH. Extrapolation of kinetic results also indicates that 90% of Hg(0) can be removed if 3 Lb/MMacf of Darco-KB pretreated with 3% of SCl2 or S2Cl2 is used. Mercuric sulfide was identified as one of the principal products of the Hg(0)/SCl2 or Hg(0)/S2Cl2 reactions. Additionally, about 8% of SCl2 or S2Cl2 in aqueous solutions is converted to sulfide ions, which would precipitate mercuric ion from FGD solution.
The Effect of Information Level on Human-Agent Interaction for Route Planning
2015-12-01
13 Fig. 4 Experiment 1 shows regression results for time spent at DP predicting posttest trust group membership for the high LOI...decision time by pretest trust group membership. Bars denote standard error (SE). DT at DP was evaluated to see if it predicted posttest trust... group . Linear regression indicated that DT at DP was not a significant predictor of posttest trust for the Low or the Medium LOI conditions; however, it
Azzi, Salah; Steunou, Virginie; Rousseau, Alexandra; Rossignol, Sylvie; Thibaud, Nathalie; Danton, Fabienne; Le Jule, Marilyne; Gicquel, Christine; Le Bouc, Yves; Netchine, Irène
2011-02-01
Many human syndromes involve a loss of imprinting (LOI) due to a loss (LOM) or a gain of DNA methylation (GOM). Most LOI occur as mosaics and can therefore be difficult to detect with conventional methods. The human imprinted 11p15 region is crucial for the control of fetal growth, and LOI at this locus is associated with two clinical disorders with opposite phenotypes: Beckwith-Wiedemann syndrome (BWS), characterized by fetal overgrowth and a high risk of tumors, and Russell-Silver syndrome (RSS), characterized by intrauterine and postnatal growth restriction. Until recently, we have been using Southern blotting for the diagnosis of RSS and BWS. We describe here a powerful quantitative technique, allele-specific methylated multiplex real-time quantitative PCR (ASMM RTQ-PCR), for the diagnosis of these two complex disorders. We first checked the specificity of the probes and primers used for ASMM RTQ-PCR. We then carried out statistical validation for this method, on both retrospective and prospective populations of patients. This analysis demonstrated that ASMM RTQ-PCR is more sensitive than Southern blotting for detecting low degree of LOI. Moreover, ASMM RTQ-PCR is a very rapid, reliable, simple, safe, and cost effective method. © 2011 Wiley-Liss, Inc.
NASA Astrophysics Data System (ADS)
Spirou, Gloria M.; Vitkin, I. Alex; Wilson, B. C.; Whelan, William M.; Henrichs, Paul M.; Mehta, Ketan; Miller, Tom; Yee, Andrew; Meador, James; Oraevsky, Alexander A.
2004-07-01
Laser Optoacoustic Imaging System (LOIS) combines high tissue contrast based on the optical properties of tissue and high spatial resolution based on ultrawide-band ultrasonic detection. Patients undergoing thermal or photodynamic therapy of prostate cancer may benefit from capability of LOIS to detect and monitor treatment-induced changes in tissue optical properties and blood flow. The performance of a prototype LOIS was evaluated via 2D optoacoustic images of dye-colored objects of various shapes, small tubes with blood simulating veins and arteries, and thermally coagulated portions of chicken breasts imbedded tissue-mimicking gelatin phantoms. The optoacoustic image contrast was proportional to the ratio of the absorption coefficient between the embedded objects and the surrounding gel. The contrast of the venous blood relative to the background exceeded 250%, and the contrast of the thermally coagulated portions of flesh relative to the untreated tissue ranged between -100% to +200%, dependent on the optical wavelength. We used a 32-element optoacoustic transducer array and a novel design of low-noise preamplifiers and wide-band amplifiers to perform these studies. The system was optimized for imaging at a depth of ~50 mm. The system spatial resolution was better than 1-mm. The advantages and limitations of various signal-processing methods were investigated. LOIS demonstrates clinical potential for non- or minimally-invasive monitoring of treatment-induced tissue changes.
NASA Astrophysics Data System (ADS)
Murray, R.; Lascu, I.; Plank, C.
2007-12-01
Deming Lake is a small (<1 square km), deep (about 17m), meromictic kettle lake situated near the prairie- forest boundary, in Itasca State Park, MN. Because of the lake's location and morphology, the accumulated sediments comprise a high-resolution record of limnological and ecological changes in response to Holocene climate variations. We used a shore perpendicular transect of three cores (located in littoral, mid-slope, and profundal settings) and ground penetrating radar (GPR) profiles to investigate Holocene lake-level variability at Deming. Cores were sampled continuously at a 1-2 cm resolution and sediment composition (in terms of percent organic matter, carbonate material, and minerogenic residue) was determined via loss on ignition (LOI). Isothermal remanent magnetization (IRM) and anhysteretic remanent magnetization (ARM) were used as proxies of magnetic mineral concentration and grain size. Four lithostratigraphic units were identified and correlated between cores based on these analyses. Changes in GPR facies corroborate the correlation between the two shallow cores. In order to inform our interpretation of down-core variations in magnetic properties and LOI values in terms of variations in lake depth, a suite of over 70 modern sediment samples were collected from the basin and analyzed. LOI compositional variability across the basin was high, with no clear trends related to depth or distance from shore. A sharp decrease in minerogenic content was observed at depths consistent with a predicted wave-base of 0.5 m, but aside from this trend it appears the steep slopes of much of the basin promote gravity driven slumping and mixing of sediments at depth. In the profundal sediments IRM values are routinely 5% higher than in the slope and littoral environments, while ARM/IRM ratios indicate an increase in magnetic grain size with water depth. We infer that an increase in coarse organic material in the shallow-water cores of Deming records a period of aridity (associated with a decrease lake-level less than 2m based on GPR profiles) and/or increased water clarity during the regionally expansive mid-Holocene dry period. We do not see clear evidence of late-Holocene lake level change of a significant magnitude (i.e. >1m). While remanence measurements (especially IRM) often correlate with the LOI residue, interference in the IRM resulting from the dissolution of magnetic minerals casts uncertainty into the reliability of our magnetic measurements as a signal of climate driven limnological change. Additional measurements must be performed before definite interpretations about the lake-level changes at Deming can be made. We suggest that future studies look more closely at the near-shore record (water depths <1m), as our results indicate shoreline migration in response to moisture balance fluctuations during the last 1000 years (as recorded at numerous sites in the great plains and upper Midwest) may have been subtle.
XAFS SPECTROSCOPY RESULTS FOR PM SAMPLES FROM RESIDUAL FUEL OIL
X-ray absorption fine structure (XAFS spectroscopy data were obtained from particulate samples produced by the combustion of residual fuel oil in a 732-kW fire-tube boiler at EPA's National Risk Management Research Laboratory in North Carolina. Residual oil flyash (ROFA) from fo...
Cements for Structural Concrete in Cold Regions.
1977-10-01
ability to reduce the early evolu- tion of heat: slag and obsidian, pumicite and calcined shale, fly-ash , tuff and calcined diatomite , natural cement...and uncalcined diatomite . Variations in initial set times of cements can be controlled ‘cy varying the percentages of different cement mixtures . Wh it
Implementation of EPA criminal enforcement strategy for RCRA interim status facilities
DOE Office of Scientific and Technical Information (OSTI.GOV)
Not Available
1985-11-15
The directive discusses criminal enforcement priorities and procedures related to the RCRA section 3007(e)(2) Loss of Interim Status (LOIS) provision, including: (1) identifying/targeting facilities with violations, (2) verifying receipt of RCRA 3007 letters, and (3) inspections of facilities. The directive supplements directive no. 9930.0-1 RCRA LOIS Enforcement Strategy, dated October 15, 1985. The directive is supplemented by directive no. 9930.0-2a, Accepting Nonhazardous Waste After Losing Interim Status, dated December 20, 1986.
1990-05-01
et au suivi des trajcctoires d’a&onefs se subdivise en trois parties: (a) un recueil des r~sumis des contributions - le texte integral sera...Organisation for the Safety of Air Navigation EUROCONTROL Engineering Directorate 72, rue de la Loi B- 1040 Bruxelles Belgium PANEL EXECUTIVE From Europe...AIRCRAFT MOTION IN MOVING AIR b R.Brockhaus DETERMINATION DES LOIS DE GUIDAGE QUASI-OPTIMALES EN TEMPS REEL POUR 4 A-3/4 DES TRAJECTOIRES DAVIONS DE COMBAT
Advanced Technology for SAM Systems Analysis Synthesis and Simulation
1984-05-01
aides de nature op~ratlcnnelle, Einanci~rv et technicue. Ainsi peut-on esp6rer iu’en r~sulte- ront les rhoix les rroilloura. Trois des neuf expras~s...EAST (Royal Military College of Science, UNITED KINGDOM) traite des structures des boucles de quidaqe at compare los lois d’ali- gnement t~l~command~es...avec les lois de navigation des missiles autoquid~s. Dants los structures en alignement, le Dr EAST montre qu’il est possible et indispensable
ERIC Educational Resources Information Center
Apple, Michael W.
2013-01-01
What roles can and should teachers' unions play in the deliberations, debates, and conflicts over school reform in a time when education sits at the center of so much of our economic, political, ideological, and cultural tensions? Lois Weiner's new book, "The Future of Our Schools: Teachers Unions and Social Justice," speaks…
[Particle size determination by radioisotope x-ray absorptiometry with sedimentation method].
Matsui, Y; Furuta, T; Miyagawa, S
1976-09-01
The possibility of radioisotope X-ray absorptiometry to determine the particle size of powder in conjunction with sedimentation was investigated. The experimental accuracy was primarily determined by Cow and X-ray intensity. where Co'=weight concentration of the particle in the suspension w'=(micron/rho)l/(mu/rho)s-rhol/rhos rho; density micron/rho; mass absorption coefficient, suffix l and s indicate dispersion and particle, respectively. The radiosiotopes, Fe-55, Pu-238 and Cd-109 have high w-values over the wide range of the atomic number. However, a source of high micron value such as Fe-55 is not suitable because the optimal X-ray transmission length, Lopt is decided by the expression, micronlLopt approximately 2/(1+C'ow') by using Cd-109 AgKX-ray source, the weight size distribution of particles from the heavy elements such as PbO2 to light elements such as Al2O3 or flyash was determined.
The hypothesis that health effects associated with coal combustion fly-ash particles are exacerbated by the simultaneous presence of iron and soot was tested through two sets of experiments. The first set created prototype particles from complete and partial combustion, or oxygen...
40 CFR 75.57 - General recordkeeping provisions.
Code of Federal Regulations, 2014 CFR
2014-07-01
... stack gas (percent H2O, rounded to the nearest tenth). If the continuous moisture monitoring system... record daily the following information for CO2 mass emissions: (i) Date; (ii) Daily combustion-formed CO2... whether optional procedure to adjust combustion-formed CO2 mass emissions for carbon retained in flyash...
40 CFR 75.57 - General recordkeeping provisions.
Code of Federal Regulations, 2013 CFR
2013-07-01
... stack gas (percent H2O, rounded to the nearest tenth). If the continuous moisture monitoring system... record daily the following information for CO2 mass emissions: (i) Date; (ii) Daily combustion-formed CO2... whether optional procedure to adjust combustion-formed CO2 mass emissions for carbon retained in flyash...
40 CFR 75.57 - General recordkeeping provisions.
Code of Federal Regulations, 2011 CFR
2011-07-01
... stack gas (percent H2O, rounded to the nearest tenth). If the continuous moisture monitoring system... record daily the following information for CO2 mass emissions: (i) Date; (ii) Daily combustion-formed CO2... whether optional procedure to adjust combustion-formed CO2 mass emissions for carbon retained in flyash...
40 CFR 75.57 - General recordkeeping provisions.
Code of Federal Regulations, 2012 CFR
2012-07-01
... stack gas (percent H2O, rounded to the nearest tenth). If the continuous moisture monitoring system... record daily the following information for CO2 mass emissions: (i) Date; (ii) Daily combustion-formed CO2... whether optional procedure to adjust combustion-formed CO2 mass emissions for carbon retained in flyash...
The hypothesis that health effects associated with coal combustion fly-ash particles are exacerbated by the simultaneous presence of iron and soot was tested through two sets of experiments. The first set created prototype particles from complete and partial combustion, or oxygen...
XAFS SPECTROSCOPY ANALYSIS OF SELECTED HAP ELEMENTS IN FINE PM DERIVED FROM COAL COMBUSTION
X-ray absorption fine structure (XAFS) spectroscopy has been used to investigate the valence states and molecular structures of sulfur (S), chromium (Cr), arsenic (As), and zinc (Zn) in fine particulate matter (PM) separated from coal flyash produced in a realistic combustion sys...
Phosphorus retention by fly-ash amended filter media in aged bioretention cells
USDA-ARS?s Scientific Manuscript database
Bioretention cells (BRCs) have shown potential for stormwater quantity and quality control. However, the phosphorus (P) removal in BRC has been variable due to differences of soil properties in filter media. The objectives of this research were to identify and evaluate P accumulation in filter media...
Preparation of Flame Retardant Polyacrylonitrile Fabric Based on Sol-Gel and Layer-by-Layer Assembly
Ren, Yuanlin; Huo, Tongguo; Qin, Yiwen; Liu, Xiaohui
2018-01-01
This paper aims to develop a novel method, i.e., sol-gel combined with layer-by-layer assembly technology, to impart flame retardancy on polyacrylonitrile (PAN) fabrics. Silica-sol was synthesized via the sol-gel process and acted as cationic solution, and phytic acid (PA) was used as the anionic medium. Flame-retardant-treated PAN fabric (FR-PAN) could achieve excellent flame retardancy with 10 bilayer (10BL) coating through layer-by-layer assembly. The structure of the fabrics was characterized by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The thermal stability and flame retardancy were evaluated by thermogravimetric (TG) analysis, cone calorimetry (CC) and limiting oxygen index (LOI). The LOI value of the coated fabric was up to 33.2 vol % and the char residue at 800 °C also increased to 57 wt %. Cone calorimetry tests revealed that, compared to the control fabric, the peak of heat release rate (PHRR) and total heat release (THR) of FR-PAN decreased by 66% and 73%, respectively. These results indicated that sol-gel combined with layer-by-layer assembly technique could impart PAN fabric with satisfactory flame-retardant properties, showing an efficient flame retardant strategy for PAN fabric. PMID:29570646
Ren, Yuanlin; Huo, Tongguo; Qin, Yiwen; Liu, Xiaohui
2018-03-23
This paper aims to develop a novel method, i.e., sol-gel combined with layer-by-layer assembly technology, to impart flame retardancy on polyacrylonitrile (PAN) fabrics. Silica-sol was synthesized via the sol-gel process and acted as cationic solution, and phytic acid (PA) was used as the anionic medium. Flame-retardant-treated PAN fabric (FR-PAN) could achieve excellent flame retardancy with 10 bilayer (10BL) coating through layer-by-layer assembly. The structure of the fabrics was characterized by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). The thermal stability and flame retardancy were evaluated by thermogravimetric (TG) analysis, cone calorimetry (CC) and limiting oxygen index (LOI). The LOI value of the coated fabric was up to 33.2 vol % and the char residue at 800 °C also increased to 57 wt %. Cone calorimetry tests revealed that, compared to the control fabric, the peak of heat release rate (PHRR) and total heat release (THR) of FR-PAN decreased by 66% and 73%, respectively. These results indicated that sol-gel combined with layer-by-layer assembly technique could impart PAN fabric with satisfactory flame-retardant properties, showing an efficient flame retardant strategy for PAN fabric.
NASA Astrophysics Data System (ADS)
Zhang, Zhifan; Wu, Weihong; Zhang, Mengjiao; Qu, Jiamin; Shi, Lin; Qu, Hongqiang; Xu, Jianzhong
2017-12-01
As a novel and efficient halogen-free composite flame retardant, zinc borate (4ZnO·B2O3·H2O)/reduction graphene oxide (RGO) hybrid material (ZB/RGO) was designed and synthesized using a facile route involving nano-engineering. The unique structure and composition of ZB/RGO were efficaciously confirmed by XRD, FTIR, SEM, TEM, and TG. The incorporation of 7.71 wt% ZB/RGO could significantly enhance the synergistic effect with Mg(OH)2 (MH) when mixed with poly(vinyl chloride) (PVC) as a flame retardant and smoke suppressant, as evaluated by limited oxygen index (LOI), microscale combustion calorimetry (MCC), and a cone calorimetry test (CCT) and compared with PVC, PVC/ZB, PVC/MH, and PVC/ZB/MH blends. The PVC/ZB/RGO/MH formulation could achieve an LOI value of 29.5% (24% higher than neat PVC). More importantly, the heat release rate (HRR), peak heat release rate (PHRR), smoke production rate (SPR), perk smoke production rate (PSPR), total smoke production (TSP), and mass amount loss (MAL) were considerably reduced in CCT, especially the PHRR, TSP, and MAL values for PVC/ZB/RGO/MH blends were reduced to 35%, 34%, and 15%, respectively. This study showed that the design of the novel material might provide a reference for the future development of halogen-free flame retardants consisting of inorganic salt and carbon material, which exhibit excellent flame retardant and smoke suppressant behavior.
1981-09-01
doessais do torborsotour MAKILA nous avons choisi trois easais gui ont pour objet die asiuier qoolguos ones des conditions oxposees prece6demisont et gui...46laLore one lin dv d~bit. Los ossais ao banc consistent A 6rablir cette loi poor 6n fonictionnement aui eol do sorte I cqutiie couvrei lensemble du...laisserons de c6t6 le facteur de ddcroissanco du prix en fonction du rang de s6rie ( loi de Wright) parce que, do par sa g6ndralit6, il n’est pas influenc6
Energy Information Abstracts Annual 1988. Volume 13.
ERIC Educational Resources Information Center
Yuster, Leigh C., Ed.; And Others
This publication is a compilation of information and resource material concerning energy for the year 1988. The first section details the coverage and usage of this volume. Section 2 contains a review of events in 1988, a compilation of statistical information, an article concerning coal flyash utilization, and a listing of conferences and events…
The goal of this study was to determine the fate of source particle tracer elements following repeated intratracheal instillation (IT) to rats. PM samples comprised Mt. St. Helens ash (MSH) with no water-soluble metals, and oil flyash emission PM (EPM) with water-leachable solubl...
XAFS spectroscopy has been employed to evaluate the effect of fuel compositions and combustion conditions on the amount, form, and distribution of sulfur and nickel in size-fractionated ROFA PM. Analysis of S K-edge XANES establish that sulfate is abundant in all PM. However, dep...
The paper gives results of experiments in a pilot-scale rotary kiln incinerator simulator where a mixture of chlorinated and brominated surrogate waste was burned in the presence of injected fly-ash from a coal-fired utility boiler. Measurements were made of semivolatile products...
Remote Sensing of the Propagation Environment (La Teledetection du Milieu de Propagation)
1992-02-01
iadio prpo1agatioi pujposes may be t t the o it et fi fiction. In the Jsk forniirism, the rle i ad not the ^tio * , nmbiiture is a sunid, to, fb loi ...described by Theevaf-tioftv duct sigiificaitly ,Mfects? X-bandradar Liu, Kitsais, and.Businger (LKB model) [5], was used to detitio i-i i*ilitie.bf loi ... Trois sondes ant 0t6 plactes respectiveatent A 1.5 at, rioures A 20 GHz, onpeut no considdrer- quo le premier 10 m, et -25-m au-dessus do ]a mor. Ces
Stability in Aerospace Systems (La Stabilite dans Les Systemes Aerospatiaux)
1993-02-01
collect&e); lois dc contrt~lc en Vol en atmosphý,es tr~s turbulentes; crit~res. b) Contr6le de 1V6coulement autour des ailes et du fuselage. Cz et Cx...On voit quAh beaucoup dgards, et bien plus quo rechercho des regles do "chaos de~terministo". d’autres secteurs ; dlactivitA, l’aironautiquc a db et...innovatrices par le risque de converger vers one solution qui nest pas ki rapport a celles basees sur Ia loi dite "en er", bonne do fait de Ia non
Dynamique d'un oscillateur photoréfractif : instabilités et analogie avec la loi de Curie-Weiss
NASA Astrophysics Data System (ADS)
Mathey, P.; Odoulov, S. G.; Rytz, D.
2002-06-01
La dynamique et l'état stationnaire du faisceau issu d'une cavité oscillante comprenant un cristal non-linéaire de titanate de baryum utilisé en tant que miroir à conjugaison de phase sont étudiés. Le paramètre du système étant le gain du milieu non-linéaire, les dépendances de l'intensité de l'oscillation et de l'inverse du temps de réponse sont similaires aux lois de Curie en physique du solide.
Workshop on Physics with Neutral Kaon Beam at JLab (KL2016) Mini-Proceedings
DOE Office of Scientific and Technical Information (OSTI.GOV)
Strakovsky, Igor I.; Amaryan, Moskov; Chudakov, Eugene A.
2016-05-01
The KL2016 Workshop is following the Letter of Intent LoI12-15-001 "Physics Opportunities with Secondary KL beam at JLab" submitted to PAC43 with the main focus on the physics of excited hyperons produced by the Kaon beam on unpolarized and polarized targets with GlueX setup in Hall D. Such studies will broaden a physics program of hadron spectroscopy extending it to the strange sector. The Workshop was organized to get a feedback from the community to strengthen physics motivation of the LoI and prepare a full proposal.
Analysis of standard reference materials by absolute INAA
NASA Astrophysics Data System (ADS)
Heft, R. E.; Koszykowski, R. F.
1981-07-01
Three standard reference materials: flyash, soil, and ASI 4340 steel, are analyzed by a method of absolute instrumental neutron activation analysis. Two different light water pool-type reactors were used to produce equivalent analytical results even though the epithermal to thermal flux ratio in one reactor was higher than that in the other by a factor of two.
Leachable transition metals are considered to be important mediators in the biological effects of ambient particulate matter (PM) and model particles such as oil-fly ashes (OFA). We determined metal driven Fenton activity in 10 OFA in the presence of hydrogen peroxide using elect...
NASA Astrophysics Data System (ADS)
Chee Siang, GO
2017-07-01
Experimental test was carried out to determine the temperature rise characteristics of Portland-Fly-Ash Cement (CEM II/B-V, 42.5N) of Blaine fineness 418.6m2/kg and 444.6m2/kg respectively for 20MPa mass concrete under adiabatic condition. The estimation on adiabatic temperature rise by way of CIRIA C660 method (Construction Industry Research & Information Information) was adopted to verify and validate the hot-box test results by simulating the heat generation curve of the concrete under semi-adiabatic condition. Test result found that Portland fly-ash cement has exhibited decrease in the peak value of temperature rise and maximum temperature rise rate. The result showed that the temperature development and distribution profile, which is directly contributed from the heat of hydration of cement with time, is affected by the insulation, initial placing temperature, geometry and size of concrete mass. The mock up data showing the measured temperature differential is significantly lower than the technical specifications 20°C temperature differential requirement and the 27.7°C limiting temperature differential for granite aggregate concrete as stipulated in BS8110-2: 1985. The concrete strength test result revealed that the 28 days cubes compressive strength was above the stipulated 20MPa characteristic strength at 90 days. The test demonstrated that with proper concrete mix design, the use of Portland flyash cement, combination of chilled water and flake ice, and good insulation is effective in reducing peak temperature rise, temperature differential, and lower adiabatic temperature rise for mass concrete pours. As far as the determined adiabatic temperature rise result was concern, the established result could be inferred for in-situ thermal properties of 20MPa mass concrete application, as the result could be repeatable on account of similar type of constituent materials and concrete mix design adopted for permanent works at project site.
DOE Office of Scientific and Technical Information (OSTI.GOV)
NONE
1995-08-01
This report covers work carried out under Task 3, Preliminary R and D, under contract DE-AC22-92PC91155, {open_quotes}Engineering Development of a Coal-Fired High Performance Power Generation System{close_quotes} between DOE Pittsburgh Energy Technology Center and United Technologies Research Center. The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) by the year 2000 that is capable of (1) > 47% thermal efficiency; (2) NO{sub x}, SO{sub x} and particulates {<=}25% NSPS; (3) cost {>=}65% of heat input; (4) all solid wastes benign. In our design consideration, we have tried to render all waste streams benign andmore » if possible convert them to a commercial product. It appears that vitrified slag has commercial values. If the flyash is reinjected through the furnace, along with the dry bottom ash, then the amount of the less valuable solid waste stream (ash) can be minimized. A limitation on this procedure arises if it results in the buildup of toxic metal concentrations in either the slag, the flyash or other APCD components. We have assembled analytical tools to describe the progress of specific toxic metals in our system. The outline of the analytical procedure is presented in the first section of this report. The strengths and corrosion resistance of five candidate refractories have been studied in this quarter. Some of the results are presented and compared for selected preparation conditions (mixing, drying time and drying temperatures). A 100 hour pilot-scale stagging combustor test of the prototype radiant panel is being planned. Several potential refractory brick materials are under review and five will be selected for the first 100 hour test. The design of the prototype panel is presented along with some of the test requirements.« less
Gothwal, Vijaya K; Srinivas, Marmamula; Rao, Gullapalli N
2013-05-01
To examine the psychometric characteristics of the World Health Organization quality of life instrument-modified Indian version (modified WHOQOL) and its subscales in adults with visual impairment (VI) using Rasch analysis. Cross-sectional data were of people aged ≥40 years with VI (n = 1,333) who responded to the modified WHOQOL in the Andhra Pradesh Eye Disease Study, India. Rasch analysis was used to explore the instrument and its subscales for key indices such as measurement precision by person separation reliability, PSR (i.e., discrimination between strata of participants' health-related QOL [HRQOL], recommended minimum value 0.8), unidimensionality (i.e., measurement of a single construct), and targeting (i.e., matching of item difficulty to participants' HRQOL). Rasch-guided iterative approach including category re-organization to enable threshold ordering and item deletion to overcome multidimensionality resulted in a unidimensional 9-item WHOQOL and a 6-item level of independence (LOI) subscale with adequate PSR (0.81 and 0.82, respectively). Targeting was sub-optimal for both (-1.58 logits for WHOQOL and -2.55 logits for the subscale). Remaining subscales were dysfunctional. The WHOQOL and LOI subscale can be improved and shortened, and the Rasch-revised versions are likely to assess the HROQL of VI patients best because of their brevity, reliability, and unidimensionality.
Dwivedi, S; Srivastava, S; Mishra, S; Dixit, B; Kumar, A; Tripathi, R D
2008-10-30
The present investigation was carried out to screen native plants growing in fly-ash (FA) contaminated areas near National Thermal Power Corporation, Tanda, Uttar Pradesh, India with a view to using them for the eco-restoration of the area. A total number of 17 plants (9 aquatic, 6 terrestrial and 2 algal species) were collected and screened for heavy metal (Fe, Zn, Cu, Mo, B, Si, Al, Cr, Pb, Cd, Hg and As) accumulation. Differential accumulation of various heavy metals by different species of plants was observed. Hydrilla verticillata was found to be the most efficient metal accumulator among 9 aquatic plants, Eclipta alba among 6 terrestrial plants and Phormedium papyraceum between 2 algal species. In general, the maximum levels of most metals were found in terrestrial plants while the lowest in algal species. However, translocation of the metals from root to shoot was found to be higher in aquatic plants than terrestrial ones. These results suggest that various aquatic, terrestrial and algal species of plants may be used in a synergistic way to remediate and restore the FA contaminated areas.
Meyer, William R.; Tucci, Patrick
1979-01-01
Part of the Indiana Dunes National Lakeshore shares a common boundary with the Northern Indiana Public Service Company (NIPSCO). This area is underlain by unconsolidated deposits approximately 180 feet thick. NIPSCO accumulates fly ash from the burning of coal in electric-power generating units in settling ponds. Seepage from the ponds has raised ground-water levels above natural levels approximately 15 feet under the ponds and more than 10 feet within the Lakeshore. NIPSCO is presently (1977) constructing a nuclear powerplant, and construction activities include pumping ground water to dewater the construction site. The company has installed a slurry wall around the site to prevent lowering of ground-water levels within the Lakeshore. Plans call for continuous pumping through at least December 1979. A multilayered digital flow model was constructed to simulate the ground-water system. The model was used to demonstrate the effects of seepage from the fly-ash ponds on ground-water levels. Also, the model indicated a decline of 3 feet or less in the upper sand unit and 5 feet or less in the lower sand unit within the Lakeshore.
NASA Astrophysics Data System (ADS)
Sinha, Deepa A., Dr; Verma, A. K., Dr
2017-08-01
This paper presents the results of M60 grade of concrete. M60 grade of concrete is achieved by maximum density technique. Concrete is brittle and weak in tension and develops cracks during curing and due to thermal expansion / contraction over a period ot time. Thus the effect of addition of 1% steel fibre is studied. For ages, concrete has been one of the widely used materials for construction. When cement is manufactured, every one ton of cement produces around one ton of carbon dioxide leading to global warming and also as natural resources are finishing, so use of supplementary cementitious material like alccofine and flyash is used as partial replacement of cement is considered. The effect of binary and ternary blend on the strength characteristics is studied. The results indicate that the concrete made with alccofine and flyash generally show excellent fresh and hardened properties. The ternary system that is Portland cement-fly ash-Alccofine concrete was found to increase the strength of concrete when compared to concrete made with Portland cement or even from Portland cement and fly ash.
LOI/SOHO constraints on oblique rotation of the solar core
NASA Astrophysics Data System (ADS)
Gizon, L.; Appourchaux, T.; Gough, D. O.
The Sun is usually assumed to rotate about a single axis, tilted with respect to the ecliptic normal by an angle of 7.25 degrees. Although we have an excellent knowledge of the direction of the rotation axis of the photospheric layers, we cannot exclude a priori that the direction of the rotation axis could vary as a function of radius. We have tried to check whether the assumption of rotation about a unique axis is consistent with helioseismic data. We report on an attempt to measure the directions of the pulsation axes of several low-degree modes of oscillation in the LOI/SOHO Fourier spectra.
Small animal optoacoustic tomography system for molecular imaging of contrast agents
NASA Astrophysics Data System (ADS)
Su, Richard; Liopo, Anton; Ermilov, Sergey A.; Oraevsky, Alexander A.
2016-03-01
We developed a new and improved Laser Optoacoustic Imaging System, LOIS-3D for preclinical research applications in small animal models. The advancements include (i) a new stabilized imaging module with a more homogeneous illumination of the mouse yielding a better spatial resolution (<0.2 mm) and (ii) a new low noise amplifier incorporated into the ultrasonic probe and providing the noise equivalent pressure around 2 Pa resulting in increased signal-to-noise ratio and the optical absorption sensitivity of about 0.15 cm-1. We also improved scan time and the image reconstruction times. This prototype has been commercialized for a number of biomedical research applications, such as imaging vascularization and measuring hemoglobin / oxyhemoglobin distribution in the organs as well as imaging exogenous or endogenous optoacoustic contrast agents. As examples, we present in vivo experiments using phantoms and mice with and without tumor injected with contrast agents with indocyanine green (ICG). LOIS-3D was capable of detecting ~1-2 pmole of the ICG, in tissues with relatively low blood content. With its high sensitivity and excellent spatial resolution LOIS-3D is an advanced alternative to fluorescence and bioluminescence based modalities for molecular imaging in live mice.
Twenty-three years of vegetation change in a fly-ash leachate impacted meadow
Pavlovic, Noel B.; Leicht-Young, Stacey A.; Wilcox, Douglas; Hiebert, Ron; Murphy, Marilyn K.; Mason, Daniel; Frohnapple, Krystal
2009-01-01
1. Blag Slough, located in Indiana Dunes National Lakeshore, has received leachates from nearby fly-ash ponds for 13 years (1967-1980). We have monitored vegetation and sediment of Blag Slough since 1982, two years after the sealing of the fly-ash ponds and one year after the substrate was first exposed. The pH of the soil has increased one order of magnitude from 3.0 to 4.0 over the 23 years (1982-2005). If the pH further increases the solubility of many heavy metals will decrease, except for arsenic. We provide evidence that boron and zinc were bioaccumulating in the leaves of woody plants in 1984. The ratio of leaf concentration and soil concentration of aluminum suggests this element was not bioaccumulating in woody plants in 1984. 2. Soil concentrations of iron, aluminum, arsenic, and strontium were higher nearest the fly-ash ponds in 2005. The southwest corner of Blag Slough and middle position of transect X had the highest elevated levels of these metals and correlated with the occurrence of mixed spikerush association (dominated by Eleocharis olivacea). 3. Only a few exotic species occurred in the Blag Slough. Common reed (Phragmites australis) was among such species that occurred in three large clones. Other exotic species included dandelion (Taraxacum officinale), mullein (Verbascum thapsis), Jerusalem oak goosefoot (Chenopodium botrys), and sheep sorrel (Rumex acetosella). Ruderal species have occurred including thistle (Cirsium spp.), fire weed (Erechtites hieracifolium), and horseweed (Conyza canadensis). While occasional cattail (Typha) have been sampled and mapped in Blag Slough they have never persisted for very long. 4. Species richness leveled off between 1991 and 2005, except for Transect X that had a peak in 1986-7. After an extreme rainfall event in August 18, 1990, Transect V had an average water depth of 0.70 cm, W had 7.1 cm, and X had 26.90 cm. Richness in Transect X declined to a low level in 1990 and 1991 after the extreme flooding event because this transect had the deepest surface water. 5. Typical late successional vegetation associations developed since 1991 include blue joint grass (Calamagrostis canadensis) and buttonbush (Cephalanthus occidentalis), but large areas consist of disturbance-dependent mosaics of rush (Juncus effusus) and other species. The large expanses of woolly sedge (Scirpus cyperinus) that dominated in the 1980’s was replaced by rush. 6. Late-successional associations (Glyceria canadensis and Calamagrostis canadensis) were closer to the wetland edge compared to the other associations after the dewatering. This pattern occurred because wet meadow vegetation persisted at the wetland edge during the period of industrial flooding, but since then these associations expanded greatly into the north half of Blag Slough. 7. Richness, diversity, and floristic quality index (FQI) increased with time at the plot, association, association trajectories, and wetland levels; whereas mean conservatism scores (mean C), the basis of FQI calculation, decreased in time. The high C values, assigned to coastal plain disjunct species and shrubs by judgment of botanists based on their empirical xii experience including regional or state level plant conservation designations are largely responsible for the contradicted trend between FQI and C. Such contradiction highlights a problem with the subjective assignment of C values, and thus the inadequacy of application of FQI in these wetland systems. 8. Occurrence of interveinal clearing in winged sumac (Rhus copallina), late boneset (Eupatorium serotinum), and black dewberry (Rubus occidentalis) suggest a potential phytotoxicity by heavy metals. However, cause-effect relationship between the metals and the plants are yet to be investigated. Nevertheless, boron and zinc accumulation ratios in leaves of woody plants (Betula populifolia, Populus tremuloides, Rhus copallina, and Rubus sp.) in 1984 suggest that boron and zinc were bioaccumulating in those species. Known toxicity effects of aluminum suggest that plants with vein clearing may be experiencing toxic effects of aluminum despite leaf concentrations 58 to 193 ppm. 9. In a greenhouse experiment, rye (Secale cereale) and radish (Raphanus sativus) germinated poorly in the sediments from Blag Slough having high concentrations of heavy metals (ZN, Mn, B, and NH4+) compared to potting soil. However, rye and radish plants grown in Blag Slough soil had shorter shoots and roots, lower root and shoot mass, and lower root to shoot mass ratios compared to plants grown in potting soil. These results suggest some effect of the soil constituents on rye and radish growth. 10. Positive signs in the recovery of Blag Slough include the increase in soil pH, the increasing dominance of late successional grasses, and the establishment of wetland zonation relative to seasonal water depth. Some areas of Blag Slough near the fly-ash ponds that continue to have high concentrations of heavy metals continue to be devoid of vegetation or are dominated by early successional species such as green spikerush. Localized heavy metal concentrations, evidence for zinc and boron bioaccumulation in 1984, vein clearing that persists today, effects of soil on rye and racish growth, and slow succession in the southern portion of Blag Slough suggest further toxicity study is necessary to better assess the impacts on this wetland ecosystem and identify restoration actions.
Childhood mourning. An impossible desire in Lois Lowry's a Summer to Die.
Hyun, Aerin
2012-01-01
In Lois Lowry's A Summer to Die, protagonist Meg Chalmers appears wiser than her thirteen years, able to handle such painful crises as her sister's death to leukemia, moving to a new town in the middle of a school year, and witnessing the birth of her neighbors' son with an ease and grace equal to the remarkably well-adjusted adults in her life. She also appears to have better sense than some of the not-so-well-adjusted adults who threaten to disrupt her world, such as Clarice Callaway (the town busybody) and Martin Huntington (the-opportunistic lawyer) and even at times her adult friends and neighbors Will, Ben, and Maria.
NASA Astrophysics Data System (ADS)
Yogesh, M.; Rao, A. N. Hari
2018-04-01
Natural fibre based composites are under intensive study due to their eco friendly nature and peculiar properties. The advantage of natural fibres is their continuous supply, easy and safe handling, and biodegradable nature. Although natural fibres exhibit admirable physical and mechanical properties, it varies with the plant source, species, geography, and so forth. Pineapple leave fibre (PALF) is one of the abundantly available waste materials in India and has not been studied yet. The work has been carried out to fabrication and study the mechanical characterization of Pineapple Leaf fiber reinforced Vinylester composites filled with different particulate fillers. These results are compared with those of a similar set of glass fiber reinforced Vinylester composites filled with same particulate fillers. It is evident that the density values for Pineapple leaf fiber (PALF) - Vinylester composites increase with the particulate filler content and void fractions in these composites also increase. The test results show that with the presence of particulate fillers, micro hardness of the PALF-Vinylester composites has improved. Among all the composites under this investigation, the maximum hardness value is recorded for PALF-Vinylester composite filled with 20 wt% alumina. In this investigation the maximum value of ILSS has been recorded for the PALF-Vinylester composite with 20 wt% of Flyash.
NASA Astrophysics Data System (ADS)
Brock-Utne, Birgit; Mercer, Malcolm
2014-12-01
Africans speak African languages in their everyday lives while lessons in school are delivered in an exogenous language. In many places adult education is also carried out in a language the majority of people do not speak. The exogenous languages, which are the languages of the former colonial powers and mastered just by a small African elite, are used in most parliaments in Africa and in most newspapers. This problem is largely ignored by the international community. An argument often put forward against using African languages as Languages of Instruction (LOIs) is that there are so many of them, and it may be problematic to select one as an LOI. But is this really the case? And does one need to select one language? The main work of the Centre for Advanced Studies of African Society (CASAS) located in Cape Town has been to harmonise the written forms of most African languages so that these languages can be used as LOIs and as languages of government and the press. This paper examines in some detail the work undertaken by CASAS, its successes and challenges. It shows that the political process of getting the harmonised languages adopted is more difficult and unpredictable than the linguistic work itself.
GENOMIC IMPRINTING, DISRUPTED PLACENTAL EXPRESSION, AND SPECIATION
Brekke, Thomas D.; Henry, Lindy A.; Good, Jeffrey M.
2016-01-01
The importance of regulatory incompatibilities to the early stages of speciation remains unclear. Hybrid mammals often show extreme parent-of-origin growth effects that are thought to be a consequence of disrupted genetic imprinting (parent-specific epigenetic gene silencing) during early development. Here we test the long-standing hypothesis that abnormal hybrid growth reflects disrupted gene expression due to loss of imprinting (LOI) in hybrid placentas, resulting in dosage imbalances between paternal growth factors and maternal growth repressors. We analyzed placental gene expression in reciprocal dwarf hamster hybrids that show extreme parent-of-origin growth effects relative to their parental species. In massively enlarged hybrid placentas, we observed both extensive transgressive expression of growth-related genes and bi-allelic expression of many genes that were paternally silenced in normal sized hybrids. However, the apparent widespread disruption of paternal silencing was coupled with reduced gene expression levels overall. These patterns are contrary to the predictions of the LOI model and indicate that hybrid misexpression of dosage sensitive genes is caused by other regulatory mechanisms in this system. Collectively, our results support a central role for disrupted gene expression and imprinting in the evolution of mammalian hybrid inviability, but call into question the generality of the widely invoked LOI model. PMID:27714796
Optimizing spectral wave estimates with adjoint-based sensitivity maps
NASA Astrophysics Data System (ADS)
Orzech, Mark; Veeramony, Jay; Flampouris, Stylianos
2014-04-01
A discrete numerical adjoint has recently been developed for the stochastic wave model SWAN. In the present study, this adjoint code is used to construct spectral sensitivity maps for two nearshore domains. The maps display the correlations of spectral energy levels throughout the domain with the observed energy levels at a selected location or region of interest (LOI/ROI), providing a full spectrum of values at all locations in the domain. We investigate the effectiveness of sensitivity maps based on significant wave height ( H s ) in determining alternate offshore instrument deployment sites when a chosen nearshore location or region is inaccessible. Wave and bathymetry datasets are employed from one shallower, small-scale domain (Duck, NC) and one deeper, larger-scale domain (San Diego, CA). The effects of seasonal changes in wave climate, errors in bathymetry, and multiple assimilation points on sensitivity map shapes and model performance are investigated. Model accuracy is evaluated by comparing spectral statistics as well as with an RMS skill score, which estimates a mean model-data error across all spectral bins. Results indicate that data assimilation from identified high-sensitivity alternate locations consistently improves model performance at nearshore LOIs, while assimilation from low-sensitivity locations results in lesser or no improvement. Use of sub-sampled or alongshore-averaged bathymetry has a domain-specific effect on model performance when assimilating from a high-sensitivity alternate location. When multiple alternate assimilation locations are used from areas of lower sensitivity, model performance may be worse than with a single, high-sensitivity assimilation point.
Rocca, Stefania; van Zomeren, André; Costa, Giulia; Dijkstra, Joris J; Comans, Rob N J; Lombardi, Francesco
2013-02-01
The focus of this study was to identify the main compounds affecting the weight changes of bottom ash (BA) in conventional loss on ignition (LOI) tests and to obtain a better understanding of the individual processes in heterogeneous (waste) materials such as BA. Evaluations were performed on BA samples from a refuse derived fuel incineration (RDF-I) plant and a hospital waste incineration (HW-I) plant using thermogravimetric analysis and subsequent mass spectrometry (TG-MS) analysis of the gaseous thermal decomposition products. Results of TG-MS analysis on RDF-I BA indicated that the LOI measured at 550°C was due to moisture evaporation and dehydration of Ca(OH)(2) and hydrocalumite. Results for the HW-I BA showed that LOI at 550°C was predominantly related to the elemental carbon (EC) content of the sample. Decomposition of CaCO(3) around 700°C was identified in both materials. In addition, we have identified reaction mechanisms that underestimate the EC and overestimate the CaCO(3) contents of the HW-I BA during TG-MS analyses. These types of artefacts are expected to occur also when conventional LOI methods are adopted, in particular for materials that contain CaO/Ca(OH)(2) in combination with EC and/or organic carbon, such as e.g. municipal solid waste incineration (MSWI) bottom and fly ashes. We suggest that the same mechanisms that we have found (i.e. in situ carbonation) can also occur during combustion of the waste in the incinerator (between 450 and 650°C) demonstrating that the presence of carbonate in bottom ash is not necessarily indicative for weathering. These results may also give direction to further optimization of waste incineration technologies with regard to stimulating in situ carbonation during incineration and subsequent potential improvement of the leaching behavior of bottom ash. Copyright © 2012 Elsevier Ltd. All rights reserved.
NASA Astrophysics Data System (ADS)
Song, Young-Joo; Bae, Jonghee; Kim, Young-Rok; Kim, Bang-Yeop
2016-12-01
In this study, the uncertainty requirements for orbit, attitude, and burn performance were estimated and analyzed for the execution of the 1st lunar orbit insertion (LOI) maneuver of the Korea Pathfinder Lunar Orbiter (KPLO) mission. During the early design phase of the system, associate analysis is an essential design factor as the 1st LOI maneuver is the largest burn that utilizes the onboard propulsion system; the success of the lunar capture is directly affected by the performance achieved. For the analysis, the spacecraft is assumed to have already approached the periselene with a hyperbolic arrival trajectory around the moon. In addition, diverse arrival conditions and mission constraints were considered, such as varying periselene approach velocity, altitude, and orbital period of the capture orbit after execution of the 1st LOI maneuver. The current analysis assumed an impulsive LOI maneuver, and two-body equations of motion were adapted to simplify the problem for a preliminary analysis. Monte Carlo simulations were performed for the statistical analysis to analyze diverse uncertainties that might arise at the moment when the maneuver is executed. As a result, three major requirements were analyzed and estimated for the early design phase. First, the minimum requirements were estimated for the burn performance to be captured around the moon. Second, the requirements for orbit, attitude, and maneuver burn performances were simultaneously estimated and analyzed to maintain the 1st elliptical orbit achieved around the moon within the specified orbital period. Finally, the dispersion requirements on the B-plane aiming at target points to meet the target insertion goal were analyzed and can be utilized as reference target guidelines for a mid-course correction (MCC) maneuver during the transfer. More detailed system requirements for the KPLO mission, particularly for the spacecraft bus itself and for the flight dynamics subsystem at the ground control center, are expected to be prepared and established based on the current results, including a contingency trajectory design plan.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Durham, M.D.
Several tasks have been completed in a program to evaluate additives to improve fine particle collection in electrostatic precipitators. Screening tests and laboratory evaluations of additives are summarized in this report. Over 20 additives were evaluated; four were found to improve flyash precipitation rates. The Insitec particle analyzer was also evaluated; test results show that the analyzer will provide accurate sizing and counting information for particles in the size range of {le} 10 {mu}m dia.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Durham, M.D.
Several tasks have been completed in a program to evaluate additives to improve fine particle collection in electrostatic precipitators. Screening tests and laboratory evaluations of additives are summarized in this report. Over 20 additives were evaluated; four were found to improve flyash precipitation rates. The Insitec particle analyzer was also evaluated; test results show that the analyzer will provide accurate sizing and counting information for particles in the size range of [le] 10 [mu]m dia.
Spectroscopic studies of fly ash-based geopolymers
NASA Astrophysics Data System (ADS)
Rożek, Piotr; Król, Magdalena; Mozgawa, Włodzimierz
2018-06-01
In the present work fly-ash based geopolymers with different contents of alkali-activator and water were prepared. Alkali-activation was conducted with sodium hydroxide (NaOH) at the SiO2/Na2O molar ratio of 3, 4, and 5. Water content was at the ratio of 30, 40, and 50 wt% in respect to the weight of the fly ash. Structural and microstructural characterization (FT-IR spectroscopy, 29Si and 27Al MAS NMR, X-ray diffraction, SEM) of the specimens as well as compressive strength and apparent density measurements were carried out. The obtained geopolymers are mainly amorphous due to the presence of disordered aluminosilicate phases. However, hydroxysodalite have been identified as a crystalline product of geopolymerization. The major band in the mid-infrared spectra (at about 1000 cm-1) is related to Sisbnd O(Si,Al) asymmetric stretching vibrations and is an indicator of the geopolymeric network formation. Several component bands in this region can be noticed after the decomposition process. Decomposition of band at 1450 cm-1 (vibrations of Csbnd O bonds in bicarbonate group) has been also conducted. Higher NaOH content favors carbonation, inasmuch as the intensity of the band then increases. Both water and alkaline activator contents have an influence on compressive strength and microstructure of the obtained fly-ash based geopolymers.
NASA Astrophysics Data System (ADS)
Singh, Lalit Mohan; Kumar, Mukesh; Sahoo, B. K.; Sapra, B. K.; Kumar, Rajesh
Coal is one of the most important source used for electrical power generation. Its combustion part known as fly ash is used in the manufacturing of bricks, sheets, cement, land filling etc. Coal and its by-products have significant amounts of radionuclide's including uranium, thorium which is the ultimate source of the radioactive gas radon and thoron respectively. Radiation hazard from airborne emissions of coal-fired power plants have been cited as possible causes of health in environmental. Assessment of the radiation exposure from coal burning is critically dependent on the concentration of radioactive elements in coal and in the fly ash. In the present study, samples of coal and flyash were collected from Rajghat Power Plant and Badarpur Thermal Power Plant, New Delhi, India. Radon exhalation is important parameter for the estimation of radiation risk from various materials. Solis State Nuclear Track Detector based sealed Can Technique (using LR-115 type II) has been used for measurement radon exhalation rate. Also accumulation chamber based Continuous Radon Monitor and Continuous Thoron Monitor have been used for radon masss exhalation and thoron surface exhalation rate respectively. Natural radioactivity has been measured using a low level NaI(Tl) detector based on gamma ray spectrometry.
Flammability on textile of flight crew professional clothing
NASA Astrophysics Data System (ADS)
Silva-Santos, M. C.; Oliveira, M. S.; Giacomin, A. M.; Laktim, M. C.; Baruque-Ramos, J.
2017-10-01
The issue about flammability of textile materials employed in passenger cabins of commercial aircrafts is an important part of safety routines planning. Once an in-flight emergency initiated with fire or smoke aboard, time becomes critical and the entire crew must be involved in the solution. It is part of the crew functions, notably the attendants, the in-flight firefighting. This study compares the values of textile material of flight attendant working cloths and galley curtain fabric with regard to flammability and Limiting Oxygen Index (LOI). Values to the professional clothing material indicate that they are flammable and the curtains, self-extinguishing. Thus, despite of the occurrences of fire outbreaks in aircrafts are unexceptional, the use of other materials and technologies for uniforms, such as alternative textile fibers and flame retardant finishes should be considered as well as the establishment of performance limits regarding flame and fire exposing.
Chen, Hongda; Wang, Jihui; Ding, Anxin; Han, Xia; Sun, Ziheng
2018-01-01
In order to improve the efficiency of intumescent flame retardants (IFRs), a novel macromolecular charring agent named poly(ethanediamine-1,3,5-triazine-p-4-amino-2,2,6,6-tetramethylpiperidine) (PETAT) with gas phase and condense phase synergistic flame-retardant capability was synthesized and subsequently dispersed into polypropylene (PP) in combination with ammonium polyphosphate (APP) via a melt blending method. The chemical structure of PETAT was investigated by Fourier transform infrared spectroscopy (FTIR), and 1H nuclear magnetic resonance (NMR) spectroscopy. Thermal properties of the PETAT and IFR systems were tested by thermogravimetric-derivative thermogravimetric analysis (TGA-DTG) and thermogravimetry–Fourier transform infrared spectroscopy (TG-FTIR). The mechanical properties, thermal stability, flame-retardant properties, water resistance, and structures of char residue in flame-retardant composites were characterized using tensile and flexural strength property tests, TGA, limiting oxygen index (LOI) values before and after soaking, underwritten laboratory-94 (UL-94) vertical burning test, cone calorimetric test (CCT), scanning electron microscopy with energy dispersive X-ray spectrometry (SEM-EDXS), and FTIR. The results indicated that PETAT was successfully synthesized, and when the ratio of APP to PETAT was 2:1 with 25 wt % loading, the novel IFR system could reduce the deterioration of tensile strength and enhance the flexural strength of composites. Meanwhile, the flame-retardant composite was able to pass the UL-94 V-0 rating with an LOI value of 30.3%, and the peak of heat release rate (PHRR), total heat release (THR), and material fire hazard values were considerably decreased compared with others. In addition, composites also exhibited excellent water resistance properties compared with traditional IFR composites. SEM-EDXS and FTIR analyses of the char residues, as well as TG-FTIR analyses of IFR were used to investigate the flame-retardant mechanism of the APP/PETAT IFR system. The results indicated that the efficient flame retardancy of PP/IFR composites could be attributed to the synergism of the free radical-quenching and char layer-protecting mechanisms in the gas phase and condense phase, respectively. PMID:29324716
Chen, Hongda; Wang, Jihui; Ni, Aiqing; Ding, Anxin; Han, Xia; Sun, Ziheng
2018-01-11
In order to improve the efficiency of intumescent flame retardants (IFRs), a novel macromolecular charring agent named poly(ethanediamine-1,3,5-triazine-p-4-amino-2,2,6,6-tetramethylpiperidine) (PETAT) with gas phase and condense phase synergistic flame-retardant capability was synthesized and subsequently dispersed into polypropylene (PP) in combination with ammonium polyphosphate (APP) via a melt blending method. The chemical structure of PETAT was investigated by Fourier transform infrared spectroscopy (FTIR), and ¹H nuclear magnetic resonance (NMR) spectroscopy. Thermal properties of the PETAT and IFR systems were tested by thermogravimetric-derivative thermogravimetric analysis (TGA-DTG) and thermogravimetry-Fourier transform infrared spectroscopy (TG-FTIR). The mechanical properties, thermal stability, flame-retardant properties, water resistance, and structures of char residue in flame-retardant composites were characterized using tensile and flexural strength property tests, TGA, limiting oxygen index (LOI) values before and after soaking, underwritten laboratory-94 (UL-94) vertical burning test, cone calorimetric test (CCT), scanning electron microscopy with energy dispersive X-ray spectrometry (SEM-EDXS), and FTIR. The results indicated that PETAT was successfully synthesized, and when the ratio of APP to PETAT was 2:1 with 25 wt % loading, the novel IFR system could reduce the deterioration of tensile strength and enhance the flexural strength of composites. Meanwhile, the flame-retardant composite was able to pass the UL-94 V-0 rating with an LOI value of 30.3%, and the peak of heat release rate (PHRR), total heat release (THR), and material fire hazard values were considerably decreased compared with others. In addition, composites also exhibited excellent water resistance properties compared with traditional IFR composites. SEM-EDXS and FTIR analyses of the char residues, as well as TG-FTIR analyses of IFR were used to investigate the flame-retardant mechanism of the APP/PETAT IFR system. The results indicated that the efficient flame retardancy of PP/IFR composites could be attributed to the synergism of the free radical-quenching and char layer-protecting mechanisms in the gas phase and condense phase, respectively.
Particulate Air Pollution Control for Army Coal-Fired Boiler Plants.
1983-03-01
Army flue gas . The condensed material usually is sticky and emissions control . Of the current new technologies. traps the flyash on the bag, where it... control device is made a matter of convenience. The location Flue gas temperature control is an important factor of other components is given the prime...consideration. *in the application of baghouses to flue gas particulate This often results in the particle-laden gas being forced control . Bag
DOE Office of Scientific and Technical Information (OSTI.GOV)
Dodoo, J.N.; Okoh, J.M.; Yilmaz, E.
The objective is to investigate the kinetics of beneficiation of fly ash by carbon burnout. The three year project that was proposed is a joint venture between Delmarva Power, a power generating company on the eastern shore of Maryland, and the University of Maryland Eastern Shore. The studies have focused on the beneficiation of fly ash by carbon burnout. The increasing use of coal fly ash as pozzolanic material in Portland cement concrete means that there is the highest economic potential in marketability of large volumes of fly ash. For the concrete industry to consider large scale use the flymore » ash must be of the highest quality. This means that the residual carbon content of the fly ash must have an acceptable loss on ignition (LOI) value, usually between 7--2% residual carbon. The economic gains to be had from low-carbon ash is a fact that is generally accepted by the electricity generating companies. However, since the cost of producing low-carbon in large quantities, based on present technology, far outweighs any financial gains, no electrical power company using coal as its fuel at present considers the effort worthwhile. The concrete industry would use fly ash in cement concrete mix if it can be assured of its LOI value. At present no utility company would give such assurance. Hence with several million tons of fly ash produced by a single power plant per year all that can be done is to dump the fly ash in landfills. The kinetics of fly ash beneficiation have been investigated in the zone II kinetic regime, using a Cahn TG 121 microbalance in the temperature 550--750{degrees}C. The P{sub 02} and total surface area dependence of the reaction kinetics were determined using a vacuum accessory attached to the microbalance and a surface area analyzer (ASAP 2010), respectively.« less
Alcoa Pressure Calcination Process for Alumina
NASA Astrophysics Data System (ADS)
Sucech, S. W.; Misra, C.
A new alumina calcination process developed at Alcoa Laboratories is described. Alumina is calcined in two stages. In the first stage, alumina hydrate is heated indirectly to 500°C in a decomposer vessel. Released water is recovered as process steam at 110 psig pressure. Partial transformation of gibbsite to boehmite occurs under hydrothermal conditions of the decomposer. The product from the decomposer containing about 5% LOI is then calcined by direct heating to 850°C to obtain smelting grade alumina. The final product is highly attrition resistant, has a surface area of 50-80 m2/g and a LOI of less than 1%. Accounting for the recovered steam, the effective fuel consumption for the new calcination process is only 1.6 GJ/t A12O3.
Dynamic Performance Assessment of Side Facing Troop Seats During Impact
2016-04-30
Force (lbs) Chest Resultant (G) Peak Lumbar Force (lbs) DRZ VDT6586 CV-22 1120 53.14 1604 38.48 VDT6590 CH-53 1575 64.34 2522 43.01 VDT6594 H...0.1375 32 VDT6590 B2 CV CH-53 LOIS 29.96 48.92 YES 1575 64.34 2522 43.01 0.6799 0.6185 0.9767 0.2567 0.2955 0.1815 19.5 VDT6591 C2 CV CH-53 LARD 24.19...0.1712 0.1375 32 B2 CV CH-53 LOIS 29.96 48.92 YES 1575 64.34 2522 43.01 0.6799 0.6185 0.9767 0.2567 0.2955 0.1815 19.5 C2 CV CH-53 LARD 24.19 40.51 YES
ELECTROSTATIC SURFACE STRUCTURES OF COAL AND MINERAL PARTICLES
DOE Office of Scientific and Technical Information (OSTI.GOV)
NONE
It is the purpose of this research to study electrostatic charging mechanisms related to electrostatic beneficiation of coal with the goal of improving models of separation and the design of electrostatic separators. Areas addressed in this technical progress report are (a) electrostatic beneficiation of Pittsburgh #8 coal powders as a function of grind size and processing atmosphere; (b) the use of fluorescent micro-spheres to probe the charge distribution on the surfaces of coal particles; (c) the use of electrostatic beneficiation to recover unburned carbon from flyash; (d) the development of research instruments for investigation of charging properties of coal. Pittsburghmore » #8 powders were beneficiated as a function of grind size and under three atmosphere conditions: fresh ground in air , after 24 hours of air exposure, or under N2 atmosphere. The feed and processed powders were analyzed by a variety of methods including moisture, ash, total sulfur, and pyritic sulfur content. Mass distribution and cumulative charge of the processed powders were also measured. Fresh ground coal performed the best in electrostatic beneficiation. Results are compared with those of similar studies conducted on Pittsburgh #8 powders last year (April 1, 1997 to September 30, 1997). Polystyrene latex spheres were charged and deposited onto coal particles that had been passed through the electrostatic separator and collected onto insulating filters. The observations suggest bipolar charging of individual particles and patches of charge on the particles which may be associated with particular maceral types or with mineral inclusions. A preliminary investigation was performed on eletrostatic separation of unburned carbon particles from flyash. Approximately 25% of the flyash acquired positive charge in the copper tribocharger. This compares with 75% of fresh ground coal. The negatively charged material had a slightly reduced ash content suggesting some enrichment of carbonaceous material. There was also evidence that the carbon is present at a higher ratio in larger particles than in small particles. An ultraviolet photoelectron counter for use in ambient atmosphere is nearing completion. The counter will be used to measure work functions of different maceral and mineral types in the coal matrix. A Particle Image Analyzer for measuring size and charge of airborne particles is also under contruction and its current status is presented. A charged, monodisperse, droplet generator is also being constructed for calibration of the Particle Image Analyzer and other airborne particle analyzers in our labs.« less
Criteria for the Use of Lime-Cement-Flyash on Airport Pavements
1989-12-01
conducted in which core sarples were obtained from Newark, Portland, and JFK airports . The samples were tested for modulus of resilience and unconfined...Port Authority of New York and New Jersey to finalize the plans for core removal at Newark and JFK Airports . At the meeting, it was agreed that cores...would be extracted at JFK Airport later that month. Similarly, core extractions would begin at Newark Airport the next day after campletion of the JFK
[Volatile ashes and their biological effect. 2. Fibrogenic effect of volatile ashes].
Woźniak, H; Wiecek, E; Lao, I; Wojtczak, J
1989-01-01
In experiments on white Wistar rats fibrogenic effects of 6 samples of fly-ashes collected from electric precipitators in power engineering plants have been evaluated. The coal came from different national deposits. All the ashes have been found to contain: quartz and mullite, 3 ashes contained additionally orthoclase, whereas 1, apart from quartz and mullite, contained kaolinite; naturally radioactive elements (Ra226, K40, Th228) and trace elements (As, Ba, Be, Cd, Ce, Cu, Fe, Pa, Mo, Ni, Pb, Se, U Zu). Experimental pneumoconiosis was induced through intratracheal administration of single doses of 50 mg of dust; the experiment was carried out at 3 time intervals of 3, 6 and 9 months. The fibrogenic activity was evaluated both qualitatively (histopathological methods) and quantitatively (lung weight, hydroxyproline content in lungs, dust elimination from lungs); control groups consisted of animals which obtained NaCl solution and quartz sands. Fly-ashes were found to exhibit different fibrogenic effects, yet, their fibrogenic activity was weaker, compared to quartz sands. No clear correlation was found between fibrogenic effects of ashes and test physico-chemical properties, such as the content of SiO2, trace elements or naturally radioactive elements. Analysis of occupational diseases (for the period section): (1979-1983) demonstrated occupational diseases of dust-related aetiology among power engineering workers, pneumoconioses, constituting 7.8% of 127 cases of occupational diseases.
Wei, Liqiu; Che, Ruxin; Jiang, Yijun; Yu, Bing
2013-12-01
Microwave absorbing material plays a great role in electromagnetic pollution controlling, electromagnetic interference shielding and stealth technology, etc. The core-nanoshell composite materials doped with La were prepared by a solid-state reaction method, which is applied to the electromagnetic wave absorption. The core is magnetic fly-ash hollow cenosphere, and the shell is the nanosized ferrite doped with La. The thermal decomposition process of the sample was investigated by thermogravimetry and differential thermal analysis. The morphology and components of the composite materials were investigated by the X-ray diffraction analysis, the microstructure was observed by scanning electron microscope and transmission electron microscope. The results of vibrating sample magnetometer analysis indicated that the exchange-coupling interaction happens between ferrite of magnetic fly-ash hollow cenosphere and nanosized ferrite coating, which caused outstanding magnetic properties. The microwave absorbing property of the sample was measured by reflectivity far field radar cross section of radar microwave absorbing material with vector network analyzer. The results indicated that the exchange-coupling interaction enhanced magnetic loss of composite materials. Therefore, in the frequency of 5 GHz, the reflection coefficient can achieve -24 dB. It is better than single material and is consistent with requirements of the microwave absorbing material at the low-frequency absorption. Copyright © 2013 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.
Contingency Trajectory Design for a Lunar Orbit Insertion Maneuver Failure by the LADEE Spacecraft
NASA Technical Reports Server (NTRS)
Genova, A. L.
2014-01-01
This paper presents results from a contingency trajectory analysis performed for the Lunar Atmosphere & Dust Environment Explorer (LADEE) mission in the event of a missed lunar-orbit insertion (LOI) maneuver by the LADEE spacecraft. The effects of varying solar perturbations in the vicinity of the weak stability boundary (WSB) in the Sun-Earth system on the trajectory design are analyzed and discussed. It is shown that geocentric recovery trajectory options existed for the LADEE spacecraft, depending on the spacecraft's recovery time to perform an Earth escape-prevention maneuver after the hypothetical LOI maneuver failure and subsequent path traveled through the Sun-Earth WSB. If Earth-escape occurred, a heliocentric recovery option existed, but with reduced science capacapability for the spacecraft in an eccentric, not circular near-equatorial retrograde lunar orbit.
Chen, Jingjing; Chakravarty, Pragya; Davidson, Gregg R; Wren, Daniel G; Locke, Martin A; Zhou, Ying; Brown, Garry; Cizdziel, James V
2015-04-29
The purpose of this work was to study the feasibility of using a direct mercury analyzer (DMA) to simultaneously determine mercury (Hg) and organic matter content in sediment and soils. Organic carbon was estimated by re-weighing the sample boats post analysis to obtain loss-on-ignition (LOI) data. The DMA-LOI results were statistically similar (p<0.05) to the conventional muffle furnace approach. A regression equation was developed to convert DMA-LOI data to total organic carbon (TOC), which varied between 0.2% and 13.0%. Thus, mercury analyzers based on combustion can provide accurate estimates of organic carbon content in non-calcareous sediment and soils; however, weight gain from moisture (post-analysis), measurement uncertainty, and sample representativeness should all be taken into account. Sediment cores from seasonal wetland and open water areas from six oxbow lakes in the Mississippi River alluvial flood plain were analyzed. Wetland sediments generally had higher levels of Hg than open water areas owing to a greater fraction of fine particles and higher levels of organic matter. Annual loading of Hg in open water areas was estimated at 4.3, 13.4, 19.2, 20.7, 129, and 135 ng cm(-2) yr(-1) for Beasley, Roundaway, Hampton, Washington, Wolf and Sky Lakes, respectively. Generally, the interval with the highest Hg flux was dated to the 1960s and 1970s. Copyright © 2015 Elsevier B.V. All rights reserved.
Yang, Bing; Wagner, Jennifer; Damaschke, Nathan; Yao, Tianyu; Wuerzberger-Davis, Shelly M.; Lee, Moon-Hee; Svaren, John; Miyamoto, Shigeki; Jarrard, David F.
2014-01-01
Genomic imprinting is the allele-specific expression of a gene based on parental origin. Loss of imprinting(LOI) of Insulin-like Growth Factor 2 (IGF2) during aging is important in tumorigenesis, yet the regulatory mechanisms driving this event are largely unknown. In this study oxidative stress, measured by increased NF-κB activity, induces LOI in both cancerous and noncancerous human prostate cells. Decreased expression of the enhancer-blocking element CCCTC-binding factor(CTCF) results in reduced binding of CTCF to the H19-ICR (imprint control region), a major factor in the allelic silencing of IGF2. This ICR then develops increased DNA methylation. Assays identify a recruitment of the canonical pathway proteins NF-κB p65 and p50 to the CTCF promoter associated with the co-repressor HDAC1 explaining gene repression. An IκBα super-repressor blocks oxidative stress-induced activation of NF-κB and IGF2 imprinting is maintained. In vivo experiments using IκBα mutant mice with continuous NF-κB activation demonstrate increased IGF2 LOI further confirming a central role for canonical NF-κB signaling. We conclude CTCF plays a central role in mediating the effects of NF-κB activation that result in altered imprinting both in vitro and in vivo. This novel finding connects inflammation found in aging prostate tissues with the altered epigenetic landscape. PMID:24558376
Pertinence et limitations de la loi de Mott dans les isolants désordonnés
NASA Astrophysics Data System (ADS)
Ladieu, François; Sanquer, Marc
Twenty five years ago, Mott's law was established in order to describe electrical transport in disordered insulators at low temperature. In this review, we briefly summarize the different theoretical steps involved in the rigourous derivation of Mott's law. We stress upon the fact that Mott's law gives the mean conductance of an ensemble of macroscopic samples as long as electron-electron interactions remain negligible. We then study what happens when at least one of the key assumptions of Mott's law no longer holds. We first focus on systems whose size — at least in one dimension — is not macroscopic: the optimization involved in Mott's law is no longer relevant for the measured conductance. Eventually, we try to gather different works dealing with electron-electron interactions. It is now established that interactions generally produce a stronger divergence for the electrical resistance than the one predicted by Mott's law at the lowest temperatures. But the exact shape of this divergence, as well as its interpretation, remain debated. We try to make a link between Efros and Shklovskii 's work and their famous "Coulomb gap" and a more recent work about granular media. In this latter work, the size of the grains is the key parameter for the shape of the divergence of the resistance at low temperature. We suggest this could indicate a way for a model accounting for the different shapes of divergence of the electrical resistance at the lowest temperatures. Furthermore this framework of granular media allows us to deal with non linear regime: we explain the main differences between the predictions of the hot electrons model and the ones recently derived for a d -dimensional network of grains. Il y a déjà un quart de siècle que la loi de Mott a été établie afin de décrire le transport dans les milieux isolants désordonnés à basse température. Dans cet article de revue, nous rappelons brièvement les diverses étapes théoriques nécessaires à l'établissement rigoureux de la loi de Mott. Nous insistons sur le fait que la loi de Mott ne donne que la conductance moyenne d'un ensemble d'échantillons macroscopiques, tant que les interactions entre électrons restent négligeables. Nous étudions ensuite ce qu'il se passe lorsque l'on lève au moins l'une des hypothèses nécessaires à l'établissement de la loi de Mott. Nous nous penchons d'abord sur le cas des systèmes dont au moins une dimension n'est pas macroscopique : l'optimisation contenue dans la loi de Mott n'est alors plus représentative de la conductance mesurée. Enfin, nous essayons de rassembler des travaux relatifs aux effets des interactions entre électrons. S'il est acquis que, de façon générale, les interactions entraînent une divergence de la résistance plus rapide que ne le prédit la loi de Mott aux plus basses températures, la forme exacte de cette divergence ainsi que son interprétation restent encore sujets à caution. Nous rapprochons le travail d'Efros et Shklovskii et leur célèbre "gap de Coulomb" d'un travail plus récent sur les milieux granulaires dans lequel la taille des grains joue un rôle discriminant sur la nature de la divergence de la résistance à basse température. Nous suggérons que ce rapprochement ouvre une piste pour un modèle rendant compte de manière unifiée des diverses divergences mesurées à basse température pour la résistance électrique. Cette incursion dans les modèles granulaires nous permet aussi d'aborder la question des non linéarités en exposant les différences entre les prédictions du modèle des électrons chauds et celles proposées récemment pour un réseau de grains en dimension d .
NASA Astrophysics Data System (ADS)
Roner, M.; D'Alpaos, A.; Ghinassi, M.; Marani, M.; Silvestri, S.; Franceschinis, E.; Realdon, N.
2016-07-01
Salt marshes are ubiquitous features of the tidal landscape governed by mutual feedbacks among processes of physical and biological nature. Improving our understanding of these feedbacks and of their effects on tidal geomorphological and ecological dynamics is a critical step to address issues related to salt-marsh conservation and response to changes in the environmental forcing. In particular, the spatial variation of organic and inorganic soil production processes at the marsh scale, a key piece of information to understand marsh responses to a changing climate, remains virtually unexplored. In order to characterize the relative importance of organic vs. inorganic deposition as a function of space, we collected 33 shallow soil sediment samples along three transects in the San Felice and Rigà salt marshes located in the Venice lagoon, Italy. The amount of organic matter in each sample was evaluated using Loss On Ignition (LOI), a hydrogen peroxide (H2O2) treatment, and a sodium hypochlorite (NaClO) treatment following the H2O2 treatment. The grain size distribution of the inorganic fraction was determined using laser diffraction techniques. Our study marshes exhibit a weakly concave-up profile, with maximum elevations and coarser inorganic grains along their edges. The amount of organic and inorganic matter content in the samples varies with the distance from the marsh edge and is very sensitive to the specific analysis method adopted. The use of a H2O2+NaClO treatment yields an organic matter density value which is more than double the value obtained from LOI. Overall, inorganic contributions to soil formation are greatest near the marsh edges, whereas organic soil production is the main contributor to soil accretion in the inner marsh. We interpret this pattern by considering that while plant biomass productivity is generally lower in the inner part of the marsh, organic soil decomposition rates are highest in the better aerated edge soils. Hence the higher inorganic soil content near the edge is due to the preferential deposition of inorganic sediment from the adjacent creek, and to the rapid decomposition of the relatively large biomass production. The higher organic matter content in the inner part of the marsh results from the small amounts of suspended sediment that makes it to the inner marsh, and to the low decomposition rate which more than compensates for the lower biomass productivity in the low-lying inner zones. Finally, the average soil organic carbon density from the LOI measurements is estimated to be 0.044 g C cm-3. The corresponding average carbon accumulation rate for the San Felice and Rigà salt marshes, 132 g C m-2 yr-1, highlights the considerable carbon stock and sequestration rate associated with coastal salt marshes.
Ruppel, Meri M; Gustafsson, Örjan; Rose, Neil L; Pesonen, Antto; Yang, Handong; Weckström, Jan; Palonen, Vesa; Oinonen, Markku J; Korhola, Atte
2015-12-15
Black carbon (BC) is fine particulate matter produced by the incomplete combustion of biomass and fossil fuels. It has a strong climate warming effect that is amplified in the Arctic. Long-term trends of BC play an important role in assessing the climatic effects of BC and in model validation. However, few historical BC records exist from high latitudes. We present five lake-sediment soot-BC (SBC) records from the Fennoscandian Arctic and compare them with records of spheroidal carbonaceous fly-ash particles (SCPs), another BC component, for ca. the last 120 years. The records show spatial and temporal variation in SBC fluxes. Two northernmost lakes indicate declining values from 1960 to the present, which is consistent with modeled BC deposition and atmospheric measurements in the area. However, two lakes located closer to the Kola Peninsula (Russia) have recorded increasing SBC fluxes from 1970 to the present, which is likely caused by regional industrial emissions. The increasing trend is in agreement with a Svalbard ice-core-BC record. The results suggest that BC deposition in parts of the European Arctic may have increased over the last few decades, and further studies are needed to clarify the spatial extent of the increasing BC values and to ascertain the climatic implications.
Wild fire aerosol optical properties measured by lidar at Haifa, Israel
NASA Astrophysics Data System (ADS)
Heese, Birgit; Hofer, Julian; Baars, Holger; Engelmann, Ronny; Althausen, Dietrich; Schechner, Yoav Y.
2018-04-01
Optical properties of fresh biomass burning aerosol were measured by lidar during the wild fires in Israel in November 2016. A single-wavelength lidar Polly was operated at the Technion Campus at Haifa. The detector with originally two channels at 532 and 607 nm was recently upgraded with a cross- and a co-polarised channel at 532 nm, and a rotational Raman channel at 530.2 nm. Preliminary results show high particle depolarisation ratios probably caused by soil dust and large fly-ash particles.
Cataloging in Publication; An LJ Mini-Symposium
ERIC Educational Resources Information Center
Dunlap, Connie R.; And Others
1974-01-01
A report, including statistics, on the status of the Library of Congress Cataloging in Publication (CIP) program is presented followed by commentaries by Maurice Freedman, Herbert S. Bailey, Jr., Lois Hacker, and Marvin H. Scilken. (PF)
Diffusion and plasticity at high temperature
NASA Astrophysics Data System (ADS)
Philibert, J.
1991-06-01
High temperature plastic deformation requires atomic migration whatever the mechanism of deformation. The constitutive equations contain a diffusion coefficient and the deformation rate follows an Arrhenius law. This paper will only discuss the case of viscous creep in order to elucidate the nature of the diffusion processes and the expression of the diffusion coefficient involved in alloys or compounds. La déformation plastique à haute température met en jeu des migrations atomiques, quel que soit le mécanisme de déformation. Les lois de comportement contiennent donc un coefficient de diffusion et la vitesse de déformation obéit à une loi d'Arrhenius. Dans cet article, qui ne conceme qu'un seul type de déformation, lefluage visqueux, on s'efforce de préciser la nature des processus de diffusion et du coefficient de diffusion mis en jeu dans le cas des alliages et des composés.
GRAIL TCM-5 Go/No-Go: Developing Lunar Orbit Insertion Criteria
NASA Technical Reports Server (NTRS)
Chung, Min-Kun J.
2013-01-01
The Gravity Recovery and Interior Laboratory (GRAIL) mission successfully completed mapping the Moon's gravity field to an unprecedented level. The mission success was critically dependent on the success of the Lunar Orbit Insertion (LOI). It was somewhat unfamiliar as it involved an elliptical approach from a low-energy trans-lunar cruise trajectory via Sun-Earth three-body region rather than a more conventional hyperbolic approach from a direct Earth-to-Moon transfer. In addition, how its delivery dispersion affected the science formation of the two spacecraft was not well understood. In this paper we establish a set of LOI criteria to meet all the requirements and we use these criteria to establish Go/No-Go boundaries of the last, statistical Trajectory Correction Maneuvers (TCM-5s) for operations. In the end both spacecraft were found to be within the established boundaries and TCM-5s of both spacecraft were cancelled.
Organic content influences sediment microbial fuel cell performance and community structure.
Zhao, Qing; Li, Ruying; Ji, Min; Ren, Zhiyong Jason
2016-11-01
This study constructed sediment microbial fuel cells (SMFCs) with different organic loadings without the amendment of external substrates, and it investigated how such variation affects electricity generation and microbial community structure. Results found sediment characteristics significantly influenced SMFC performance and appropriate organic content is important to maintain stable power outputs. SMFCs with loss of ignition (LOI) of 5% showed the most reliable performance in this study, while high organic content (LOI 10-16%) led to higher but very unstable voltage output because of biogas accumulation and worm activities. SMFCs with low organic content (1-3%) showed low power output. Different bacterial communities were found in SMFCs shown various power generation performance even those with similar organic contents. Thermodesulfovibrionaceae was found closely related to the system startup and Desulfobulbaceae showed great abundance in SMFCs with high power production. Copyright © 2016 Elsevier Ltd. All rights reserved.
NASA Astrophysics Data System (ADS)
Bilenker, L.; Weis, D.; Scoates, J. S.
2017-12-01
We present stable Fe and radiogenic isotope and complementary trace element data for samples from Atlantis Massif. This oceanic core complex is located at 30°N where the Atlantis Transform Fault intersects the Mid-Atlantic Ridge (MAR) and is associated with the Lost City Hydrothermal Field (LCHF). It is a unique place to investigate the abiotic and biotic geochemical processes that play a role in the alteration of both crustal and mantle seafloor rocks. The samples analyzed represent a shallow (<15 m) survey of five drill sites (IODP Expedition 357) within Atlantis Massif, varying in distance from the LCHF and MAR. Analyses were performed on a sample set spanning a wide range in degree of alteration and lithology. Bulk measurements involved dissolving whole rock powders, whereas in situ analyses were performed on digested microdrilled samples or by laser ablation. Bulk rock Fe isotope values (n = 34) are correlated with loss-on-ignition (LOI) by sample lithology and location relative to LCHF. Using LOI as a proxy for degree of alteration, this observation indicates that the Fe isotope systematics of seafloor crustal and mantle rocks preserve indicators of fluid flow and source. The Hf and Nd isotope compositions for various lithologies form all analyzed sites are homogeneous, indicating minimal alteration of these isotopic systems. Bulk Sr values provide insight into elemental exchange between seawater and the surface of Atlantis Massif and bulk Pb isotopes allow for fingerprinting of the source of basalt breccias through comparison with published Pb isotope values of MAR basalts. The new results cluster around the Pb, Hf, Nd isotopic composition of mid-ocean ridge basalt from 30.68°N and do not match samples north or south of that location. In situ Fe isotope data within three altered samples reflect varying degrees of hydrothermal and seawater interaction, where the Fe isotope ratios within each sample are likely correlated with extent of exchange or redox. Laser trace element and Pb isotope data in progress will allow us to investigate this further. This study contributes to our understanding of element mobility and mass transfer during chemical reactions within the seafloor, provides insight into the source of the lithological units and fluid flow, and allows for quantification of alteration processes.
Gupta, D K; Tripathi, R D; Rai, U N; Dwivedi, S; Mishra, Seema; Srivastava, S; Inouhe, M
2006-11-01
Seeds of Cicer arietinum L. plants are edible and a valuable source of protein. Accumulation of toxic metals in the edible part of the plant, grown in fields close to fly-ash (FA) landfills, may pose a threat to human health. In the present study, the effects of FA and its amendments with different ameliorants viz., garden soil (GS), press mud (PM) and saw dust (SD), on total soluble protein contents, amino acid composition and metal accumulation in seeds were investigated in var. CSG-8962 and var. C-235 of C. arietinum. Plants accumulated adequate amounts of essential metals viz. Fe, Cu, Zn in seeds, while the toxic metals such as Cd and Cr were taken up in smaller quantities. The accumulation of Cr and Cd was less in var. C-235 than var. CSG-8962. Amendment of FA with PM enhanced the amount of soluble protein and amino acids in both varieties and was found to be superior among all tested ameliorants. Both quantitative and qualitative analysis of amino acids showed better response in var. C-235 as compared to var. CSG-8962. Thus var. C-235 seems to be suitable for cultivation in FA contaminated areas due to more accumulation of essential metals and less accumulation of toxic metals in seeds. Application of PM may further improve the growth of plants and nutritional quality of seeds.
Direct to consumer genetic testing and the libertarian right to test.
Bonython, Wendy Elizabeth; Arnold, Bruce Baer
2017-08-20
Loi recently proposed a libertarian right to direct to consumer genetic testing (DTCGT)- independent of autonomy or utility-reflecting Cohen's work on self-ownership and Hohfeld's model of jural relations. Cohen's model of libertarianism dealt principally with self-ownership of the physical body. Although Loi adequately accounts for the physical properties of DNA, DNA is also an informational substrate, highly conserved within families. Information about the genome of relatives of the person undergoing testing may be extrapolated without requiring direct engagement with their personal physical copy of the genome, triggering rights and interests of relatives that may differ from the rights and interests of others, that is, individual consumers, testing providers and regulators. Loi argued that regulatory interference with exercise of the right required justification, whereas prima facie exercise of the right did not. Justification of regulatory interference could include 'conflict with other people's rights', 'aggressive' use of the genome and 'harming others'. Harms potentially experienced by relatives as a result of the individual's exercise of a right to test include breach of genetic privacy, violation of their right to determine when, and if, they undertake genetic testing and discrimination. Such harms may justify regulatory intervention, in the event they are recognised; motives driving 'aggressive' use of the genome may also be relevant. Each of the above criteria requires clarification, as potential redundancies and tensions exist between them, with different implications affecting different groups of rights holders. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ducman, V., E-mail: vilma.ducman@zag.si; Korat, L.
Recent innovations in geopolymer technology have led to the development of various different types of geopolymeric products, including highly porous geopolymer-based foams, which are formed by the addition of foaming agents to a geopolymer fly-ash based matrix. These agents decompose, or react with the liquid matrix or oxygen in the matrix, resulting in the release of gases which form pores prior to the hardening of the gel. The hardened structure has good mechanical and thermal properties, and can therefore be used for applications in acoustic panels and in lightweight pre-fabricated components for thermal insulation purposes. This study presents the resultsmore » of the pore-forming process in the case when two different foaming agents, i.e. aluminium powder amounting to 0.07, 0.13 and 0.20 mass. % and H{sub 2}O{sub 2} amounting to 0.5, 1.0, 1.5 and 2.0 mass. %, were added to a fly-ash geopolymer matrix. The physical, mechanical, and microstructural properties of the thus obtained foams, and the effects of the type and amount of the added foaming agent, are presented and discussed. Highly porous structures were obtained in the case of both of the investigated foaming agents, with overall porosities up to 59% when aluminium powder was added, and of up 48% when H{sub 2}O{sub 2} was added. In the latter case, when 2% of the H{sub 2}O{sub 2} foaming agent was added, finer pores (with diameters up to 500 μm) occurred in the structure, whereas somewhat larger pores (some had diameters greater than 1 mm) occurred when the same amount of aluminium powder was added. The mechanical properties of the investigated foams depended on their porosity. In the case of highly porous structures a compressive strength of 3.3 MPa was nevertheless achieved for the samples containing 0.2% of aluminium powder, and 3.7 MPa for those containing 2.0% of H{sub 2}O{sub 2}. - Highlights: • Preparation of geopolymer foams based on fly ash with the addition of Al powder or H{sub 2}O{sub 2} as foaming agents • Determination of density, porosity and mechanical properties of such foams • Characterization of foaming process by means of X-ray micro-tomography (μcT)« less
Regionalized rainfall-runoff model to estimate low flow indices
NASA Astrophysics Data System (ADS)
Garcia, Florine; Folton, Nathalie; Oudin, Ludovic
2016-04-01
Estimating low flow indices is of paramount importance to manage water resources and risk assessments. These indices are derived from river discharges which are measured at gauged stations. However, the lack of observations at ungauged sites bring the necessity of developing methods to estimate these low flow indices from observed discharges in neighboring catchments and from catchment characteristics. Different estimation methods exist. Regression or geostatistical methods performed on the low flow indices are the most common types of methods. Another less common method consists in regionalizing rainfall-runoff model parameters, from catchment characteristics or by spatial proximity, to estimate low flow indices from simulated hydrographs. Irstea developed GR2M-LoiEau, a conceptual monthly rainfall-runoff model, combined with a regionalized model of snow storage and melt. GR2M-LoiEau relies on only two parameters, which are regionalized and mapped throughout France. This model allows to cartography monthly reference low flow indices. The inputs data come from SAFRAN, the distributed mesoscale atmospheric analysis system, which provides daily solid and liquid precipitation and temperature data from everywhere in the French territory. To exploit fully these data and to estimate daily low flow indices, a new version of GR-LoiEau has been developed at a daily time step. The aim of this work is to develop and regionalize a GR-LoiEau model that can provide any daily, monthly or annual estimations of low flow indices, yet keeping only a few parameters, which is a major advantage to regionalize them. This work includes two parts. On the one hand, a daily conceptual rainfall-runoff model is developed with only three parameters in order to simulate daily and monthly low flow indices, mean annual runoff and seasonality. On the other hand, different regionalization methods, based on spatial proximity and similarity, are tested to estimate the model parameters and to simulate low flow indices in ungauged sites. The analysis is carried out on 691 French catchments that are representative of various hydro-meteorological behaviors. The results are validated with a cross-validation procedure and are compared with the ones obtained with GR4J, a conceptual rainfall-runoff model, which already provides daily estimations, but involves four parameters that cannot easily be regionalized.
78 FR 49262 - Proposed Information Collection; Comment Request
Federal Register 2010, 2011, 2012, 2013, 2014
2013-08-13
... Social Innovation Fund (SIF) Application Instructions. The application instructions will be used by... Innovation Fund; Attention Lois Nembhard, Deputy Director, Room 9601; 1201 New York Avenue NW., Washington... email at innovation@cns.gov . SUPPLEMENTARY INFORMATION: CNCS is particularly interested in comments...
1992-01-01
89 Suryadevara V. Babu, Raghunath Padiyath, Moses David. and Lois Walsh THREE-DIMENSIONAL MULTIREGION Sa SOLUTIONS OF THE...is built by simple sm -RC time constant analysis of thle buts, then thle discrete im- inispection of the bus and then itiverted to produice the driving
A Read-Aloud for English Classrooms (Read It Aloud).
ERIC Educational Resources Information Center
Richardson, Judy S.; Cantrell, R. Jeffrey
1996-01-01
Presents a read-aloud from Lois Lowry's novel "Anastasia Krupnik" showing how Anastasia's first experience writing a poem helped form negative attitudes. Discusses the selections and offers suggestions for teaching poetry and for integrating poetry in other classrooms. (SR)
Federal Register 2010, 2011, 2012, 2013, 2014
2013-06-06
... Springs Ranch, LLC (transferee) filed an application for the transfer of license for the L & M Angus Ranch..., Idaho. Applicants seek Commission approval to transfer the license for the L & M Angus Ranch Project...
Azzi, Salah; Rossignol, Sylvie; Steunou, Virginie; Sas, Theo; Thibaud, Nathalie; Danton, Fabienne; Le Jule, Maryline; Heinrichs, Claudine; Cabrol, Sylvie; Gicquel, Christine; Le Bouc, Yves; Netchine, Irene
2009-12-15
Genomic imprinting plays an important role in mammalian development. Loss of imprinting (LOI) through loss (LOM) or gain (GOM) of methylation is involved in many human disorders and cancers. The imprinted 11p15 region is crucial for the control of foetal growth and LOI at this locus is implicated in two clinically opposite disorders: Beckwith Wiedemann syndrome (BWS) with foetal overgrowth associated with an enhanced tumour risk and Russell-Silver syndrome (RSS) with intrauterine and postnatal growth restriction. So far, only a few studies have assessed multilocus LOM in human imprinting diseases. To investigate multilocus LOI syndrome, we studied the methylation status of five maternally and two paternally methylated loci in a large series (n = 167) of patients with 11p15-related foetal growth disorders. We found that 9.5% of RSS and 24% of BWS patients showed multilocus LOM at regions other than ICR1 and ICR2 11p15, respectively. Moreover, over two third of multilocus LOM RSS patients also had LOM at a second paternally methylated locus, DLK1/GTL2 IG-DMR. No additional clinical features due to LOM of other loci were found suggesting an (epi)dominant effect of the 11p15 LOM on the clinical phenotype for this series of patients. Surprisingly, four patients displayed LOM at both ICR1 and ICR2 11p15. Three of them had a RSS and one a BWS phenotype. Our results show for the first time that multilocus LOM can also concern RSS patients. Moreover, LOM can involve both paternally and maternally methylated loci in the same patient.
Tserga, Aggeliki; Binder, Alexandra M; Michels, Karin B
2017-12-01
Folic acid is an essential component of 1-carbon metabolism, which generates methyl groups for DNA methylation. Disruption of genomic imprinting leads to biallelic expression which may affect disease susceptibility possibly reflected in high levels of S -adenosyl-homocysteine (SAH) and low levels of S -adenosyl-methionine (SAM). We investigated the association between folic acid supplementation during pregnancy and loss of imprinting (LOI) of IGF2 and H19 genes in placentas and cord blood of 90 mother-child dyads in association with the methylenetetrahydrofolate reductase ( MTHFR ) genotype. Pyrosequencing was used to evaluate deviation from monoallelic expression among 47 placentas heterozygous for H19 and 37 placentas and cord blood tissues heterozygous for IGF2 and H19 methylation levels of 48 placentas. We detected relaxation of imprinting (ROI) and LOI of H19 in placentas not associated with differences in methylation levels of the H19ICR. Placentas retained monoallelic allele-specific gene expression of IGF2 , but 32.4% of cord blood samples displayed LOI of IGF2 and 10.8% showed ROI. High SAH levels were significantly associated with low H19 methylation. An interesting positive association between SAM/SAH ratio and high H19 methylation levels was detected among infants with low B 12 levels. Our data suggest profound differences in regulation of imprinting in placenta and cord blood; a lack of correlation of the methylome, transcriptome, and proteome; and a complex regulatory feedback network between free methyl groups and genomic imprinting at birth.-Tserga, A., Binder, A. M., Michels, K. B. Impact of folic acid intake during pregnancy on genomic imprinting of IGF2/H19 and 1-carbon metabolism. © FASEB.
Zlebnik, Natalie E; Carroll, Marilyn E
2015-03-01
Aerobic exercise and the attention-deficit/hyperactivity disorder medication, atomoxetine (ATO), are two monotherapies that have been shown to suppress reinstatement of cocaine-seeking in an animal model of relapse. The present study investigated the effects of combining wheel running and ATO versus each treatment alone on cocaine-seeking precipitated by cocaine and cocaine-paired cues in rats with differing susceptibility to drug abuse (i.e., high vs. low impulsive). Rats were screened for high (HiI) or low impulsivity (LoI) based on their performance on a delay-discounting task and then trained to self-administer cocaine (0.4 mg/kg/inf) for 10 days. Following 14 days of extinction, both groups were tested for reinstatement of cocaine-seeking precipitated by cocaine or cocaine-paired cues in the presence of concurrent running wheel access (W), pretreatment with ATO, or both (W+ATO). HiI rats acquired cocaine self-administration more quickly than LoI rats. While both individual treatments and W+ATO significantly attenuated cue-induced cocaine seeking in HiI and LoI rats, only W+ATO was effective in reducing cocaine-induced reinstatement compared with vehicle treatment. There were dose-dependent and phenotype-specific effects of ATO with HiI rats responsive to the low but not high ATO dose. Floor effects of ATO and W on cue-induced reinstatement prevented the assessment of combined treatment effects. These findings demonstrated greater attenuation of cue- versus cocaine-induced reinstatement by ATO and W alone and recapitulate impulsivity phenotype differences in both acquisition of cocaine self-administration and receptivity to treatment.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Nazari, E.; Rashchi, F., E-mail: rashchi@ut.ac.ir; Saba, M.
2014-12-15
Highlights: • Leaching of vanadium and nickel from fly ash (14.43% V and 5.19% Ni) in sulfuric acid was performed. • Optimization of leaching parameters was carried out using a response surface methodology. • Using optimum conditions, 94.28% V and 81.01% Ni “actual recovery” was obtained. - Abstract: Simultaneous recovery of vanadium (V) and nickel (Ni), which are classified as two of the most hazardous metal species from power plant heavy fuel fly-ash, was studied using a hydrometallurgical process consisting of acid leaching using sulfuric acid. Leaching parameters were investigated and optimized in order to maximize the recovery of bothmore » vanadium and nickel. The independent leaching parameters investigated were liquid to solid ratio (S/L) (5–12.5 wt.%), temperature (45–80 °C), sulfuric acid concentration (5–25 v/v%) and leaching time (1–5 h). Response surface methodology (RSM) was used to optimize the process parameters. The most effective parameter on the recovery of both elements was found to be temperature and the least effective was time for V and acid concentration for Ni. Based on the results, optimum condition for metals recovery (actual recovery of ca.94% for V and 81% for Ni) was determined to be solid to liquid ratio of 9.15 wt.%, temperature of 80 °C, sulfuric acid concentration of 19.47 v/v% and leaching time of 2 h. The maximum V and Ni predicted recovery of 91.34% and 80.26% was achieved.« less
Extractability, plant yield and toxicity thresholds for boron in compost
DOE Office of Scientific and Technical Information (OSTI.GOV)
Brinton, W.F.; Evans, E.; Blewett, C.
Boron (B) is a trace element essential to crop growth in small soil concentrations (0.2-1.5ppm), yet may produce plant toxicity symptoms readily as the amount in the soil solution increases over 2ppm. Our study examined commercial compost made with coal fly-ash used to prepare growing media for cultivars of varying sensitivity (corn, beans, cucumber, peas). We examined total vs. extractable boron content and relate final visual symptoms of B-toxicity to yields and tissue concentrations. Visual toxicity effects included tip burn (corn), leaf mottling and necrosis (beans and peas) and leaf mottling and cupping (cucumbers). Fly ash added to compost increasedmore » hot-water soluble (HWS) B in proportion to rate and in dependence on pH, with 30% and 10% of total-B expressed as HWS-B at a media pH of 6 and 7.5, respectively. Biomass for bean and cucumber was significantly reduced by 45 to 55%, respectively, by addition of 33% fly-ash compost to growing media (28ppm total-B) while plant tissue-B increased by 6- to 4-fold, respectively. Economic yield depressions in compost media are evident for all crops and appeared at levels of HWS-B in compost media exceeding 5 ppm. The study underscores the need for careful management of exogenous factors that may be present in composts and suggests detailed understanding of media-pH and cultivar preferences may be required in preparation of growing media in order to reduce potential negative growth effects.« less
Degradation of TBC Systems in Environments Relevant to Advanced Gas Turbines for IGCC Systems
DOE Office of Scientific and Technical Information (OSTI.GOV)
Gleeson, Brian
2014-09-30
Air plasma sprayed (APS) thermal barrier coatings (TBCs) are used to provide thermal insulation for the hottest components in gas turbines. Zirconia stabilized with 7wt% yttria (7YSZ) is the most common ceramic top coat used for turbine blades. The 7YSZ coating can be degraded from the buildup of fly-ash deposits created in the power-generation process. Fly ash from an integrated gasification combined cycle (IGCC) system can result from coal-based syngas. TBCs are also exposed to harsh gas environments containing CO 2, SO 2, and steam. Degradation from the combined effects of fly ash and harsh gas atmospheres has the potentialmore » to severely limit TBC lifetimes. The main objective of this study was to use lab-scale testing to systematically elucidate the interplay between prototypical deposit chemistries (i.e., ash and its constituents, K 2SO 4, and FeS) and environmental oxidants (i.e., O 2, H 2O and CO 2) on the degradation behavior of advanced TBC systems. Several mechanisms of early TBC failure were identified, as were the specific fly-ash constituents responsible for degradation. The reactivity of MCrAlY bondcoats used in TBC systems was also investigated. The specific roles of oxide and sulfate components were assessed, together with the complex interplay between gas composition, deposit chemistry and alloy reactivity. Bondcoat composition design strategies to mitigate corrosion were established, particularly with regard to controlling phase constitution and the amount of reactive elements the bondcoat contains in order to achieve optimal corrosion resistance.« less
Ferreira, R.F.; Lambing, J.H.; Davis, R.E.
1989-01-01
Water samples were collected from 29 sites to provide synoptic chemical data, including stable-isotope ratios, for an area of active surface coal mining and to explore the effectiveness of using the data to chemically distinguish water from different aquifers. Surface-water samples were collected from one spring, four sites on East Armells Creek, one site on Stocker Creek, and two fly-ash ponds. Streamflows in East Fork Armells Creek ranged from no flow in several upstream reaches to 2.11 cu ft/sec downstream from Colstrip, Montana. Only one tributary, Stocker Creek, was observed to contribute surface flow in the study area. Groundwater samples were collected from wells completed in Quaternary alluvium or mine spoils, Rosebud overburden, Rosebud coal bed, McKay coal bed, and sub-McKay deposits of the Tongue River Member, Paleocene Fort Union Formation. Dissolved-solids concentrations, in mg/L, were 840 at the spring, 3,100 to 5,000 in the streams, 13,000 to 22,000 in the ash ponds, and 690 to 4 ,100 in the aquifers. With few exceptions, water from the sampled spring, streams, and wells had similar concentrations of major constituents and trace elements and similar stable-isotope ratios. Water from the fly-ash ponds had larger concentrations of dissolved solids, boron, and manganese and were isotopically more enriched in deuterium and oxygen-18 than water from other sources. Water from individual aquifers could not be distinguished by either ion-composition diagrams or statistical cluster analyses. (USGS)
[Prosocial Development of Very Young Children.
ERIC Educational Resources Information Center
Pawl, Jeree, Ed.
1992-01-01
This newsletter presents five articles focusing on the social development of infants and very young children. The first article, "Sympathetic Behavior in Very Young Children," by Lois Barclay Murphy, gives examples of early sympathetic behavior, traces the development of sympathy, identifies individual patterns of sympathetic response,…
Pacific Educational Research Journal, 2000.
ERIC Educational Resources Information Center
Berg, Kathleen, Ed.; Lai, Morris, Ed.
2000-01-01
This journal features theoretical, empirical, and applied research with implications for and relevance to education in the Pacific area. This volume contains: (1) "Community Perceptions of Culture and Education on Moloka'i" (Lois A. Yamauchi, William L. Greene, Katherine T. Ratliffe, and Andrea K. Ceppi); (2) "Academic Performance…
Adolescent Services & the TC. Chapter 6.
ERIC Educational Resources Information Center
Acampora, Alfonso P., Ed.; Nebelkopf, Ethan, Ed.
This document contains seven papers from the ninth World Conference of Therapeutic Communities (TCs) that deal with adolescent clients and TCs. Papers include: (1) Preliminary Consideration on "Adolescence and the TC" (David Deitch); (2) "Daytop's Full Service Adolescent Treatment Program" (Charles Devlin and Lois Morris); (3)…
Late Holocene Environmental Changes from NY-NJ Estuaries
NASA Technical Reports Server (NTRS)
Peteet, Dorothy M.; Wong, Jennifer K.
2000-01-01
High-resolution records of environmental change in the lower Hudson estuary are quite rare. We present preliminary data from several marshes in the New York- New Jersey region in order to understand the late Holocene environmental history of this region. Our project includes salt marsh cores from Hackensack, Piermont, Staten Island, and Jamaica Bay. Our preliminary research has focused on a 11.15 m. sediment core from Piermont Marsh, New York (40 N, 74 W) in an attempt to document the Holocene environmental history of the region. Lithology, loss-on-ignition (LOI), pollen, plant macrofossils, charcoal, and foraminifera were analyzed. Core lithology consists of peat, silts, and clays that vary in color and texture. The base of the core is AMS C-14 dated to 4190 yr BP. Preliminary low-resolution analysis of the core to date includes sampling at the 1-meter interval throughout the core. LOI of the sediments ranges from 1% to 85%. Average rate of deposition is about .26 cm/yr. Major changes in pollen percentages are visible throughout the core.
Stepwise Loop Insertion Strategy for Active Site Remodeling to Generate Novel Enzyme Functions.
Hoque, Md Anarul; Zhang, Yong; Chen, Liuqing; Yang, Guangyu; Khatun, Mst Afroza; Chen, Haifeng; Hao, Liu; Feng, Yan
2017-05-19
The remodeling of active sites to generate novel biocatalysts is an attractive and challenging task. We developed a stepwise loop insertion strategy (StLois), in which randomized residue pairs are inserted into active site loops. The phosphotriesterase-like lactonase from Geobacillus kaustophilus (GkaP-PLL) was used to investigate StLois's potential for changing enzyme function. By inserting six residues into active site loop 7, the best variant ML7-B6 demonstrated a 16-fold further increase in catalytic efficiency toward ethyl-paraoxon compared with its initial template, that is a 609-fold higher, >10 7 fold substrate specificity shift relative to that of wild-type lactonase. The remodeled variants displayed 760-fold greater organophosphate hydrolysis activity toward the organophosphates parathion, diazinon, and chlorpyrifos. Structure and docking computations support the source of notably inverted enzyme specificity. Considering the fundamental importance of active site loops, the strategy has potential for the rapid generation of novel enzyme functions by loop remodeling.
Ribeiro, Simone P S; Estevão, Luciana R M; Nascimento, Regina S V
2008-01-01
Organophilic clay particles were added to a standard intumescent formulation and, since the role of clay expansion or intercalation is still a matter of much controversy, several clays with varying degrees of interlayer distances were evaluated. The composites were obtained by blending the nanostructured clay and the intumescent system with a polyethylenic copolymer. The flame-retardant properties of the materials were evaluated by the limiting oxygen index (LOI), the UL-94 rating and thermogravimetric analysis (TGA). The results showed that the addition of highly expanded clays to the ammonium polyphosphate and pentaerythritol formulation does not significantly increase the flame retardancy of the mixture, when measured by the LOI and UL-94. However, when clays with smaller basal distances were added to the intumescent formulation, a synergistic effect was observed. In contrast, the simple addition of clays to the copolymer, without the intumescent formulation, did not increase the fire retardance of the materials. PMID:27877975
Low field scaling properties of high Tc superconductor glasses
NASA Astrophysics Data System (ADS)
Giovannella, C.; Fruchter, L.; Chappert, C.
We show that the zero field cooling (ZFC) M/H curves of both the YBaCuO and the LaSrCuO granular superconductor glasses (SuG) are subjected to scaling when plotted against the reduced variable t/H1/ψ . The breaking of the scaling for too weak or too strong magnetic fields is discussed and justified by the introduction of a phenomenological fractal picture, describing the behaviour of the disordered intergranular junction network. Nous montrons que les courbes M/H caractéristiques des verres de supraconducteurs granulaires sont sujettes à une loi d'échelle lorsqu'elles sont tracées en fonction de la variable réduite t/H1/ψ. La brisure de la loi d'échelle pour des champs trop forts ou trop faibles est justifiée par l'introduction d'un modèle phénoménologique fractal capable de décrire le comportement d'un réseau désordonné des jonctions.
NASA Astrophysics Data System (ADS)
Peng, Sha; Zhou, Ming; Liu, Feiyan; Zhang, Chang; Liu, Xueqing; Liu, Jiyan; Zou, Liyong; Chen, Jia
2017-08-01
Flame-retardant polyvinyl alcohol (PVA) membranes with high transparency and flexibility were prepared by mixing an aqueous solution of a phosphorus-containing acrylic acid (AOPA) with PVA. The reaction between AOPA and PVA, the transparency, the crystallinity and the flexibility of the membrane were investigated with Fourier transform infrared spectrometry (FTIR), UV-vis light transmittance, X-ray diffraction and tensile tests, respectively. The limited oxygen index (LOI) and vertical flame (UL 94 VTM), microscale combustion calorimetry, thermogravimetric analysis (TGA) and TGA-FTIR were employed to evaluate the flame retardancy as well as to reveal the corresponding mechanisms. Results showed that PVA containing 30 wt% of AOPA can reach the UL 94 VTM V0 rating with an LOI of 27.3% and retain 95% of the original transparency of pure PVA. Adding AOPA reduces crystallinity of PVA, while the flexibility is increased. AOPA depresses the thermal degradation of PVA and promotes char formation during combustion. The proposed decomposition mechanism indicates that AOPA acts mainly in the condensed phase.
Electronic Resources: Selection and Bibliographic Control.
ERIC Educational Resources Information Center
Pattie, Ling-yuh W., Ed.; Cox, Bonnie Jean, Ed.
This book is a baseline guide for professionals and library school students on issues that concern the selection and bibliographic control of electronic resources, from both conceptual and pragmatic standpoints. The book includes the following articles: (1) "Foreward" (Lois Mai Chan); (2) "Introduction" (Ling-yuh W. (Miko)…
78 FR 69649 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2013-11-20
... Mexico Fishery Management Council; Public Meeting AGENCY: National Marine Fisheries Service (NMFS.... SUMMARY: The Gulf of Mexico Fishery Management Council (Council) will hold a Webinar of the Outreach and.../register/787609511 to register. Council address: Gulf of Mexico Fishery Management Council, 2203 North Lois...
78 FR 33070 - Gulf of Mexico Fishery Management Council; Public Meetings
Federal Register 2010, 2011, 2012, 2013, 2014
2013-06-03
... Mexico Fishery Management Council; Public Meetings AGENCY: National Marine Fisheries Service (NMFS.... SUMMARY: The Gulf of Mexico Fishery Management Council (Council) will convene a public meeting. DATES: The...; telephone: (850) 433-3336. Council address: Gulf of Mexico Fishery Management Council, 2203 North Lois...
76 FR 61103 - Medicare Program; Comprehensive Primary Care Initiative
Federal Register 2010, 2011, 2012, 2013, 2014
2011-10-03
... interest by November 15, 2011 using the LOI template provided on the Innovation Center Web site at http://www.innovation.cms.gov /. Application Submission Deadline: Applications must be received through an... practice redesign in primary care through payment reform. The Center for Medicare & Medicaid Innovation...
75 FR 7444 - Gulf of Mexico Fishery Management Council; Public Meetings
Federal Register 2010, 2011, 2012, 2013, 2014
2010-02-19
.... SUMMARY: The Gulf of Mexico Fishery Management Council (Council) will convene its Law Enforcement Advisory...., Orange Beach, AL 36561. Council address: Gulf of Mexico Fishery Management Council, 2203 North Lois... Director, Gulf of Mexico Fishery Management Council; telephone: (813) 348-1630. SUPPLEMENTARY INFORMATION...
Legislative Environmental Impact Statement: Small Intercontinental Ballistic Missile Program.
1986-11-01
beautiful shiner, and Apache trout) and four federal-candidate species (desert pupfish, Sonora chub, loach minnow, and flat-tailed horned lizard) occur...Archaeology. A Class I Inventory of Prehistoric Resources. Ethnoscience, Billings, Montana. 9-13 INV Den Beste, Ken and Lois Den Beste 1976 Backgrounded
78 FR 15707 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2013-03-12
... Mexico Fishery Management Council; Public Meeting AGENCY: National Marine Fisheries Service (NMFS... meeting. SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Standing...: (813) 874-1234. Council address: Gulf of Mexico Fishery Management Council, 2203 N. Lois Avenue, Suite...
78 FR 31519 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2013-05-24
... Mexico Fishery Management Council; Public Meeting AGENCY: National Marine Fisheries Service (NMFS... Advisory Panel meeting. SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of... Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607. FOR FURTHER...
Federal Register 2010, 2011, 2012, 2013, 2014
2010-12-22
... production (NAICS code 112). Food manufacturing (NAICS code 311). Pesticide manufacturing (NAICS code [email protected] . List of Subjects Environmental protection, Agricultural commodities, Feed additives, Food additives, Pesticides and pests, Reporting and recordkeeping requirements. Dated: December 9, 2010. Lois...
76 FR 32956 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2011-06-07
... Mexico Fishery Management Council; Public Meeting AGENCY: National Marine Fisheries Service (NMFS... meeting. SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Ecosystem... the Gulf of Mexico Fishery Management Council Office located at 2203 N. Lois Avenue, Suite 1100, Tampa...
75 FR 10760 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2010-03-09
... Mexico Fishery Management Council; Public Meeting AGENCY: National Marine Fisheries Service (NMFS.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a joint meeting of the Standing and... be held at the Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa...
77 FR 75409 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2012-12-20
... Mexico Fishery Management Council; Public Meeting AGENCY: National Marine Fisheries Service (NMFS.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Reef Fish Committee... located at 2225 North Lois Avenue, Tampa, FL 33607, 813-877-6688. Council address: Gulf of Mexico Fishery...
Air and Space Museum Apollo 40th Celebration
2009-07-19
NASA Apollo 11 Astronaut Buzz Aldrin, right, and his wife Lois stand at attention in front of the color guard during the opening of the Apollo 40th anniversary celebration held at the National Air and Space Museum, Monday, July 20, 2009 in Washington. Photo Credit: (NASA/Bill Ingalls)
"Festivals of Light": A Multicultural Celebration in Brooklyn.
ERIC Educational Resources Information Center
Singer, Judith Y.; Singer, Alan
1997-01-01
Describes a celebration developed by children, staff, and parents at Morris L. Eisenstein Learning Center (Brooklyn, New York) to share the customs of Diwali, Hannukah, Loi Krathong, Kwanzaa, Nacimiento, and Christmas with the diverse student population. Includes brief descriptions of each holiday and activities included in the center's…
75 FR 11133 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2010-03-10
... Mexico Fishery Management Council; Public Meeting AGENCY: National Marine Fisheries Service (NMFS.... SUMMARY: The Gulf of Mexico Fishery Management Council (Council) will convene a meeting of the Ad Hoc Data... Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607...
Cataloguing and Classification Section. Bibliographic Control Division. Papers.
ERIC Educational Resources Information Center
International Federation of Library Associations, The Hague (Netherlands).
Papers on cataloging, classification, and coding systems which were presented at the 1982 International Federation of Library Associations (IFLA) conference include: (1) "Numbering and Coding Systems for Bibliographic Control in Use in North America" by Lois Mai Chan (United States); (2) "A Project Undertaken by the Library of…
Of Birkenstocks and Wingtips: Open Source Licenses
ERIC Educational Resources Information Center
Gandel, Paul B.; Wheeler, Brad
2005-01-01
The notion of collaborating to create open source applications for higher education is rapidly gaining momentum. From course management systems to ERP financial systems, higher education institutions are working together to explore whether they can in fact build a better mousetrap. As Lois Brooks, of Stanford University, recently observed, the…
75 FR 7444 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2010-02-19
.... SUMMARY: The Gulf of Mexico Fishery Management Council (Council) will convene a web based meeting of the... via internet. Please go to the Gulf of Mexico Fishery Management Council's website at www.gulfcouncil.org for instructions. Council address: Gulf of Mexico Fishery Management Council, 2203 N. Lois Avenue...
76 FR 80343 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2011-12-23
... meeting. SUMMARY: The Gulf of Mexico Fishery Management Council (Council) will convene a meeting of the...: The meeting will be held at the Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607, telephone: (813) 348-1630. Council address: Gulf of Mexico Fishery...
75 FR 69402 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2010-11-12
.... SUMMARY: The Gulf of Mexico Fishery Management Council in conjunction with the Gulf & South Atlantic...) 873-8675. Council address: Gulf of Mexico Fishery Management Council, 2203 N. Lois Avenue, Suite 1100... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration RIN 0648-XA028 Gulf of...
76 FR 37328 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2011-06-27
... meeting. SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Ad Hoc...) 348-1630. Council address: Gulf of Mexico Fishery Management Council, 2203 N. Lois Avenue, Suite 1100, Tampa, FL 33607. FOR FURTHER INFORMATION CONTACT: Dr. Assane Diagne, Economist; Gulf of Mexico Fishery...
75 FR 19941 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2010-04-16
...: The Gulf of Mexico Fishery Management Council will convene a public meeting of its Outreach and... will be held at the Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607; telephone: (813) 348-1630. Council address: Gulf of Mexico Fishery Management Council...
76 FR 28733 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2011-05-18
.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a Web based meeting of the... the Gulf of Mexico Fishery Management Council's Web site at http://www.gulfcouncil.org for instructions. Council address: Gulf of Mexico Fishery Management Council, 2203 N. Lois Avenue, Suite 1100...
1994-04-01
Many Little Wars Make a Big One." Also, Lois B. McHugh , "Yugoslavia: Refugee Assistance," Congressional Research Service Report for Congress, No. 93...of all Russian oil reaching the West is handled this way, as is one-half of the nickel .28 General Valery Krasnovsky of the Russian Security Ministry
78 FR 26799 - Waterway Suitability Assessment for Expansion of Liquefied Gas Terminals; Beaumont, TX
Federal Register 2010, 2011, 2012, 2013, 2014
2013-05-08
... and request for comments. SUMMARY: In accordance with Coast Guard regulations, Martin Operating.... Martin Operating Partnership's Stanolind Cut Terminal in Beaumont, Texas submitted an LOI on January 25... refer to NVIC 01-2011 for process information and guidance in evaluating Martin Operating Partnership LP...
76 FR 13130 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2011-03-10
... Mexico Fishery Management Council; Public Meeting AGENCY: National Marine Fisheries Service (NMFS.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Ad Hoc Reef Fish... the Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607...
Macintoshed Libraries 4. Fourth Edition.
ERIC Educational Resources Information Center
Valauskas, Edward J., Ed.; Vaccaro, Bill, Ed.
This annual collection contains the following 14 papers about the use of Macintosh computers in libraries: "Of Mice and Macs: The Integration of the Macintosh into the Operations and Services of the University of Tennessee, Memphis Health Science Library" (Lois M. Bellamy); "Networking Reference CD-Roms in the Apple Library"…
DOE Office of Scientific and Technical Information (OSTI.GOV)
Tahir, Dahlang, E-mail: dtahir@fmipa.unhas.ac.id; Bakri, Fahrul; Liong, Syarifuddin
We have studied the molecular properties, structural properties, and chemical composition of composites by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) spectroscopy, and X-ray fluorescence (XRF) spectroscopy, respectively. FTIR spectra shows absorption band of hydroxyl group (-OH), methyl group (-CH{sub 3}) and aromatic group (C-C). The absorption band for aromatic group (C-C) shows the formation of carbonaceous in composites. XRF shows chemical composition of composites, which the main chemicals are SO{sub 3}, Cl, and ZnO. The loss on ignition value (LOI) of activated charcoal indicates high carbonaceous matter. The crystallite size for diffraction pattern from hydrogel polymer is aboutmore » 17 nm and for activated charcoal are about 19 nm. The crystallite size of the polymer is lower than that of activated charcoal, which make possible of the particle from filler in contact with each other to form continuous conducting polymer through polymer matrix.« less
Thermal and mechanical behavior of flame retardant epoxy-polyesterurethane blends
NASA Astrophysics Data System (ADS)
Patel, R. H.; Hirani, A. V.; Kachhia, P. H.
2016-05-01
Polyesterurethanes are used in different applications due to their unique combination of the properties like toughness, flexibility, solvent resistance, etc. Nowadays flame retardant properties of polymers are of commercial interest because of their potential use in high performance applications. In the present study attempts have been taken to improve the flame retardant properties of conventional epoxy resin by incorporating phosphorus based polyesterurethane. Polyesterurethane has been synthesized in the laboratory and characterized by chemical and instrumental analysis techniques. Thermal stability and char value of the blends have been determined using thermogravimetric analysis technique. Limiting Oxygen Index (LOI) and UL-94 test methods have been used to determine the flame retardant properties of neat polymer and their blends in film form. Mechanical properties like tensile strength, elongation and impact resistance of the blends have been found out. Polyblend of epoxy resin with phosphorus based polyesterurethane has improved flame retardant properties compare to neat epoxy resin.
Altered gene expression in human placentas after IVF/ICSI.
Nelissen, Ewka C M; Dumoulin, John C M; Busato, Florence; Ponger, Loïc; Eijssen, Lars M; Evers, Johannes L H; Tost, Jörg; van Montfoort, Aafke P A
2014-12-01
Is gene expression in placental tissue of IVF/ICSI patients altered when compared with a spontaneously conceived group, and are these alterations due to loss of imprinting (LOI) in the case of imprinted genes? An altered imprinted gene expression of H19 and Pleckstrin homology-like domain family A member 2 (PHLDA2), which was not due to LOI, was observed in human placentas after IVF/ICSI and several biological pathways were significantly overrepresented and mostly up-regulated. Genomic imprinting plays an important role in placental biology and in placental adaptive responses triggered by external stimuli. Changes in placental development and function can have dramatic effects on the fetus and its ability to cope with the intrauterine environment. An increased frequency of placenta-related problems as well as an adverse perinatal outcome is seen in IVF/ICSI derived pregnancies, but the role of placental epigenetic deregulation is not clear yet. In this prospective cohort study, a total of 115 IVF/ICSI and 138 control couples were included during pregnancy. After applying several exclusion criteria (i.e. preterm birth or stillbirth, no placental samples, pregnancy complications or birth defects), respectively, 81 and 105 placentas from IVF/ICSI and control pregnancies remained for analysis. Saliva samples were collected from both parents. We quantitatively analysed the mRNA expression of several growth-related imprinted genes [H19, insulin-like growth factor 2 (IGF2), PHLDA2, cyclin-dependent kinase inhibitor 1C (CDKN1C), mesoderm-specific transcript homolog (MEST) isoform α and β by quantitative PCR] after standardization against three housekeeping genes [Succinate dehydrogenase A (SDHA), YWHAZ and TATA-binding protein (TBP)]. A quantitative allele-specific expression analysis of the differentially expressed imprinted genes was performed to investigate LOI, independent of the mechanism of imprinting. Furthermore, a microarray analysis was carried out (n = 10 in each group) to investigate the expression of non-imprinted genes as well. Both H19 and PHLDA2 showed a significant change, respectively, a 1.3-fold (P = 0.033) and 1.5-fold (P = 0.002) increase in mRNA expression in the IVF/ICSI versus control group. However, we found no indication that there is an increased frequency of LOI in IVF/ICSI placental samples. Genome-wide mRNA expression revealed 13 significantly overrepresented biological pathways involved in metabolism, immune response, transmembrane signalling and cell cycle control, which were mostly up-regulated in the IVF/ICSI placental samples. Only a subset of samples was found to be fully informative, which unavoidably led to lower sample numbers for our LOI analysis. Our study cannot distinguish whether the reported differences in the IVF/ICSI group are exclusively attributable to the IVF/ICSI technique itself or to the underlying subfertility of the patients. Whether these placental adaptations observed in pregnancies conceived by IVF/ICSI might be connected to an adverse perinatal outcome after IVF remains unknown. However, it is possible that these differences affect fetal development and long-term patterns of gene expression, as well as maternal gestational physiology. Partly funded by an unrestricted research grant by Organon BV (now MSD BV) and GROW School for Oncology and Developmental Biology without any role in study design, data collection and analysis or preparation of the manuscript. No conflict of interests to declare. Dutch Trial Registry (NTR) number 1298. © The Author 2014. Published by Oxford University Press on behalf of the European Society of Human Reproduction and Embryology. All rights reserved. For Permissions, please email: journals.permissions@oup.com.
Zhang, Hongkun; Xu, Miaojun; Li, Bin
2016-03-01
A novel phosphorus-containing compound diphenyl-(2,5-dihydroxyphenyl)-phosphine oxide defined as DPDHPPO was synthesized and used as flame retardant and curing agent for epoxy resins (EP). The chemical structure was well characterized by Fourier transform infrared (FTIR) spectroscopy, 1H, 13C and 31P nuclear magnetic resonance. The flame retardant properties, combusting performances and thermal degradation behaviors of the cured epoxy resins were investigated by limiting oxygen index (LOI), vertical burning tests (UL-94), cone calorimeter and thermogravimetric analysis (TGA) tests. The morphologies and chemical compositions of char residues for cured epoxy resins were investigated by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), respectively. The water resistant properties were evaluated by putting the samples into distilled water at 70 degrees C for 168 h. The results revealed that the EP/40 wt% DPDHPPO/60 wt% PDA thermosets successfully passed UL-94 V-0 flammability rating and the LOI value was as high as 31.9%. The cone tests results revealed that the incorporation of DPDHPPO efficiently reduced the combustion parameters of epoxy resins thermosets, such as heat release rate (HRR), total heat release (THR) and so on. The TGA results indicated that the introduction of DPDHPPO promoted epoxy resins matrix decomposed ahead of time compared with that of pure EP and led to a higher char yield and thermal stability at high temperature. The morphological structures and analysis of XPS of char residues revealed that DPDHPPO benefited to the formation of a sufficient, compact and homogeneous char layer with rich flame retardant elements on the epoxy resins materials surface during combustion. After water resistance tests, EP/40 wt% DPDHPPO/60 wt% PDA thermosets still remained excellent flame retardancy, the moisture absorption of epoxy resins thermosets decreased with the increase of DPDHPPO contents in the thermosets due to the existing of P-C bonds and the rigid aromatic hydrophobic structure.
Geochemistry and mineralogy of fly-ash from the Mae Moh lignite deposit, Thailand
DOE Office of Scientific and Technical Information (OSTI.GOV)
Hart, B.R.; Powell, M.A.; Fyfe, W.S.
The concentration of 21 elements in fly ash from three boilers (75 MW, 150 MW, and 300 MW) at the EGAT power plant, Mae Moh, Thailand, were determined by INAA. The concentration of 10 major elements was determined by XRF. As, Co, Cr, Ni, Mo, and Sb generally increase in concentration going from bottom ash (BA) through the sequence of electrostatic precipitator ashes (ESPA) and reach maxima of As (352 ppm), Co (45 ppm), Cr (105 ppm), Mo (32 ppm), Ni (106 ppm), and Sb (15 ppm) in the ESPA. Ce, Cs, Fe, Hf, La, Sc, Ta, Tb, and Ybmore » did not exhibit concentration trends or are variable except in the case of one boiler, which showed an increase going from BA to ESPA. Only Br decreased in composition going from BA to ESPA. Rb, Sm, U, and Th showed marked variation in trends. The major elements identified by EDS were Al, Si, S, K, Ca, Fe, and Ba, with minor amounts of Mg, Na, Ti, Mn, and Sr. Al, Si, K, and Ca occur together and are present in most of the fly-ash particles. Ba was found as a major component with Ca, Al, and Si. Fe and Ca are usually associated with sulfur. Some small spheres (< 5 {mu}m) are comprised almost entirely of Fe (probably as oxide). Symplectite textures are noted in high-Fe phases. All elements except Br are significantly enriched in the fly ash relative to the coal, which contains 35% ash. Particle chemistry is consistent with the major mineral phases identified by XRD, which include: quartz, magnetite, mullite, gehlenite, anorthite, hematite, anhydrite, and clinopyroxene.« less
Tripathi, R D; Dwivedi, S; Shukla, M K; Mishra, S; Srivastava, S; Singh, R; Rai, U N; Gupta, D K
2008-02-01
Rice is a major food crop throughout the world; however, accumulation of toxic metals and metalloids in grains in contaminated environments is a matter of growing concern. Field experiments were conducted to analyze the growth performance, elemental composition (Fe, Si, Zn, Mn, Cu, Ni, Cd and As) and yield of the rice plants (Oryza sativa L. cv. Saryu-52) grown under different doses of fly-ash (FA; applied @ 10 and 100 tha(-1) denoted as FA(10) and FA(100), respectively) mixed with garden soil (GS) in combination with nitrogen fertilizer (NF; applied @ 90 and 120 kg ha(-1) denoted as NF(90) and NF(120), respectively) and blue green algae biofertilizer (BGA; applied @ 12.5 kg ha(-1) denoted as BGA(12.5)). Significant enhancement of growth was observed in the plants growing on amended soils as compared to GS and best response was obtained in amendment of FA(10)+NF(90)+BGA(12.5). Accumulation of Si, Fe, Zn and Mn was higher than Cu, Cd, Ni and As. Arsenic accumulation was detected only in FA(100) and its amendments. Inoculation of BGA(12.5) caused slight reduction in Cd, Ni and As content of plants as compared to NF(120) amendment. The high levels of stress inducible non-protein thiols (NP-SH) and cysteine in FA(100) were decreased by application of NF and BGA indicating stress amelioration. Study suggests integrated use of FA, BGA and NF for improved growth, yield and mineral composition of the rice plants besides reducing the high demand of nitrogen fertilizers.
Critical Bifocality and Circuits of Privilege: Expanding Critical Ethnographic Theory and Design
ERIC Educational Resources Information Center
Weis, Lois; Fine, Michelle
2012-01-01
In this article, Lois Weis and Michelle Fine introduce critical bifocality as a way to render visible the relations between groups to structures of power, to social policies, to history, and to large sociopolitical formations. In this collaboration, the authors draw upon ethnographic examples highlighting the macro-level structural dynamics…
Taking the Next Step: Confronting the Legacies of Slavery at Historic Sites
ERIC Educational Resources Information Center
Grim, Linnea; Wickens, K. Allison; Jecha, Jackie; Powell, Linda; Hawkins, Callie; Flanagan, Candra
2017-01-01
"Slavery is the ground zero of race relations," declared James and Lois Horton in their groundbreaking book, "Slavery and Public History." Engaging the history and legacy of slavery is a crucial step in understanding current U.S. society especially race relations. Historic sites that have connections to slavery have begun to…
Understanding Motherhood as Maturation: Maternity Scripts in Lois Lowry's "Son"
ERIC Educational Resources Information Center
Deszcz-Tryhubczak, Justyna; Marecki, Mateusz
2015-01-01
When put together with the other parts of The Giver Quartet, "Son" (2012), Lowry's recently published concluding book, emerges as an odd exception to the focus on young adult protagonists since it foregrounds the mother's perspective and addresses the issue of motherhood. It presents the reader with at least three conceptual models of…
40 CFR 63.1386 - Notification, recordkeeping, and reporting requirements.
Code of Federal Regulations, 2010 CFR
2010-07-01
... microfiche; and (iii) The owner or operator may report required information on paper or on a labeled computer... exceedance was corrected; (v) The formulation of each binder batch and the LOI and density for each product... binder formulation; (vi) Process parameter level(s) for RS and FA manufacturing lines that use process...
The Eight Best Novels for Middle-Grade Teachers.
ERIC Educational Resources Information Center
Musthafa, Bachrudin
Intended to serve an instrumental purpose for middle-grade teachers, this paper presents brief annotations of eight novels of interest to middle grade students and more elaborate comments and teaching activities for two well-known novels. The eight novels are "How to Eat Fried Worms" (Thomas Rockwell); "Number the Stars" (Lois Lowry); "Cousins"…
The Dawn of a New Professionalism in the French Academy? Academics Facing the Challenges of Change
ERIC Educational Resources Information Center
Evans, Linda; Cosnefroy, Laurent
2013-01-01
Using as an analytical framework Evans's conceptualisation of professionalism, this article examines the implications for academic professionalism in the French higher education sector of reforms and significant changes that have evolved over the last few decades, including: the "Investissements d'Avenir" programme, the "Loi de…
Using "Number the Stars" as a Springboard for Doing Social Studies
ERIC Educational Resources Information Center
Putman, Errol
2003-01-01
The Danish experience during the German occupation, presented through the experiences of the Rosen and Johansen families, provides the literary and historical background for the activities the author presents in this article. He designed the four activities for maximum student involvement, with each requiring students to respond to Lois Lowry's…
How To Become a Better Reading Teacher: Strategies for Assessment and Intervention.
ERIC Educational Resources Information Center
Putnam, Lillian R., Ed.
Reflecting the diverse philosophies and experiences of clinicians and practitioners, this book presents 30 essays that address the identification of reading strengths and weaknesses, assessment, and instructional strategies for remediation. Chapters in the book are (1) "The Role of Vision in Reading Disability" (Lois B. Bing); (2) "Problems with…
ERIC Educational Resources Information Center
International Federation of Library Associations, The Hague (Netherlands).
Papers on biological and medical science libraries which were presented at the 1985 International Federation of Library Associations (IFLA) conference include: (1) "The International Programs of the National Library of Medicine" (Lois Ann Colaianni, United States); (2) "Information Needs for International Health. A CDC (Centers for Disease…
Intumescent flame-retardant cotton produced by tannic acid and sodium hydroxide
USDA-ARS?s Scientific Manuscript database
This study showed that tannic acid can form intumescent flame-retardant coating on cotton nonwoven fabric with an aid of NaOH. Tannic acid alone altered the thermal patterns of the pyrolysis and combustion of cotton and increased the char yield, but its improvement in limiting oxygen index (LOI) wa...
Technology-Based Literature Plans for Elementary Students (Technology Links to Literacy).
ERIC Educational Resources Information Center
Wepner, Shelley B.
1991-01-01
Presents ideas for incorporating software into each guided reading phase for two realistic fiction books: Lois Lowry's "Anastasia on Her Own" and Barthe DeClements's "The Fourth Grade Wizards." Discusses how each skeletal plan uses three pieces of software to enliven students' oral and written thoughts about the books'…
76 FR 58783 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2011-09-22
.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Reef Fish Advisory.... on Friday, October 14, 2011. ADDRESSES: The meeting will be held at the Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607. Council address: Gulf of Mexico...
76 FR 37063 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2011-06-24
... meeting. SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Ad Hoc Red... held at the Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607; telephone: (813) 348-1630. Council address: Gulf of Mexico Fishery Management Council, 2203 N...
75 FR 74008 - Gulf of Mexico Fishery Management Council; Public Meetings
Federal Register 2010, 2011, 2012, 2013, 2014
2010-11-30
.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a public meeting of the Florida.... Council address: Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL... Florida/Alabama group is part of a three unit Habitat Protection Advisory Panel (AP) of the Gulf of Mexico...
75 FR 39495 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2010-07-09
.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Standing and Special... the Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607; telephone: (813) 348-1630. Council address: Gulf of Mexico Fishery Management Council, 2203 N. [[Page 39496...
76 FR 56171 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2011-09-12
.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Ad Hoc Headboat... meeting will be held at the Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL 33607; telephone: (813) 348-1630. Council address: Gulf of Mexico Fishery Management Council...
Authenticating "Number the Stars" Using Nonfiction Resources
ERIC Educational Resources Information Center
Groce, Robin D.
2009-01-01
"Number the Stars" by Lois Lowry is a popular historical novel for adolescent readers about the Nazi occupation of Copenhagen, Denmark during World War II and the efforts of Danish resisters who successfully rescued 98% of that nation's Jewish population. While this 1998 book is considered to be a fictional account, most of the events in…
Late Holocene Environmental Changes from NY-NJ Estuaries
NASA Technical Reports Server (NTRS)
Peteet, Dorothy M.
2000-01-01
High-resolution records of environmental change in the lower Hudson estuary are quite rare. We present preliminary data from several marshes in the New York- New Jersey region in order to understand the late Holocene environmental history of this region. Our project includes salt marsh cores from Hackensack, Piermont, Staten Island, and Jamaica Bay. Our preliminary research has focused on a 11.15 m sediment core from Piermont Marsh, New York (40 deg N, 74 deg W) in an attempt to document the Holocene environmental history of the region. Lithology, loss -on -ignition (LOI), pollen, plant macrofossils, charcoal, and foraminifera were analyzed. Core lithology consists of peat, silts, and clays that vary in color and texture. The base of the core is AMS C-14 dated to 4190 yr BP. Preliminary low-resolution analysis of the core to date includes sampling at the 1-meter interval throughout the core. LOI of the sediments ranges from 1% to 85%. Average rate of deposition is about .26 cm/yr. Major changes in pollen percentages are visible throughout the core.
Peng, Sha; Zhou, Ming; Liu, Feiyan; Zhang, Chang; Liu, Xueqing; Liu, Jiyan; Zou, Liyong; Chen, Jia
2017-08-01
Flame-retardant polyvinyl alcohol (PVA) membranes with high transparency and flexibility were prepared by mixing an aqueous solution of a phosphorus-containing acrylic acid (AOPA) with PVA. The reaction between AOPA and PVA, the transparency, the crystallinity and the flexibility of the membrane were investigated with Fourier transform infrared spectrometry (FTIR), UV-vis light transmittance, X-ray diffraction and tensile tests, respectively. The limited oxygen index (LOI) and vertical flame (UL 94 VTM), microscale combustion calorimetry, thermogravimetric analysis (TGA) and TGA-FTIR were employed to evaluate the flame retardancy as well as to reveal the corresponding mechanisms. Results showed that PVA containing 30 wt% of AOPA can reach the UL 94 VTM V0 rating with an LOI of 27.3% and retain 95% of the original transparency of pure PVA. Adding AOPA reduces crystallinity of PVA, while the flexibility is increased. AOPA depresses the thermal degradation of PVA and promotes char formation during combustion. The proposed decomposition mechanism indicates that AOPA acts mainly in the condensed phase.
NASA Astrophysics Data System (ADS)
Gumus, Lokman; Öztürk, Sercan; Yalçın, Cihan; Abdelnasser, Amr; Hanilçi, Nurullah; Kumral, Mustafa
2016-04-01
This study is to determine the mass/volume gain and loss of the major and trace elements during the alteration processes on Dedeninyurdu, Yergen and Fındıklıyar Fe-Cu mineralizations of the area. Fe-Cu mineralization occurred in the spilitic volcanic a rock of Saraycık Formation is associated with the different types of alteration zones which are pyritization, silicification and sericitization. The study area comprises Bekirli Formation, Saraycık Formation, Beşpınar Formation, and Ilgaz Formation. Saraycık formation consists of spilitic volcanic rocks with pelagic limestone, siltstone and chert. The ore mineralogical data show that the pyrite, chalcopyrite, covellite, hematite, malachite and goethite formed during three phases of mineralization. As well as the geologic and petrographic studies reveal three alteration zones with definite mineral assemblages; phyllic alteration (quartz + sericite + pyrite) that represents the main alteration and mineralized zone; propylitic alteration; and carbonatized sericitic alteration zone. The boundaries between these zones are gradual. Mass balance calculations suggested that the phyllic alteration zone represented by gain in Si, Fe, K, S, and LOI and loss in Mg, Ca, and Na refers to silicification, sericitization and pyritization as well as replacement of Fe-Mg silicate and plagioclase. While, in the propylitic alteration zone, enrichment of Si, Fe, Mg, LOI and S occurred with depletions of Ca, Na, and K reflecting chloritization alteration type. On the other hand, carbonatized sericitic alteration zone shows local gain in Si, CaO and K reflects the occurrence of calc-silicate alteration. All alteration zones contain a large proportion of sulfide minerals (gain in S) with increase in loss on ignition (LOI). Keywords: Alteration geochemistry; Mass balance calculation, Fe-Cu mineralization; phyllic alteration, propylitic alteration.
Lobb, Rebecca; Petermann, Lisa; Manafo, Elizabeth; Keen, Deb; Kerner, Jon
2013-01-01
Funding for transdisciplinary chronic disease prevention research has increased over the past decade. However, few studies have evaluated whether networking and knowledge exchange activities promote the creation of transdisciplinary teams to successfully respond to requests for proposals (RFPs). Such evaluations are critical to understanding how to accelerate the integration of research with practice and policy to improve population health. To examine (1) the extent of participation in pre-RFP activities among funded and nonfunded transdisciplinary coalitions that responded to a RFP for cancer and chronic disease prevention initiatives and (2) levels of agreement in proposal ratings among research, practice, and policy peer reviewers. Descriptive report of a Canadian funding initiative to increase the integration of evidence with action. Four hundred forty-nine representatives in 41 research, practice, and policy coalitions who responded to a RFP and whose proposals were peer reviewed by a transdisciplinary adjudication panel. The funder hosted 6 national meetings and issued a letter of intent (LOI) to foster research, practice, and policy collaborations before issuing a RFP. All provinces and territories in Canada were represented by the coalitions. Funded coalitions were 2.5 times more likely than nonfunded coalitions to submit a LOI. A greater proportion of funded coalitions were exposed to the pre-RFP activities (100%) compared with coalitions that were not funded (68%). Overall research, practice, and policy peer reviewer agreement was low (intraclass correlation 0.12). There is widespread interest in transdisciplinary collaborations to improve cancer and chronic disease prevention. Engagement in networking and knowledge exchange activities, and feedback from LOIs prior to submission of a final application, may contribute to stronger proposals and subsequent funding success. Future evaluations should examine best practices for transdisciplinary peer review to facilitate funding of proposals that on balance have both scientific rigor and are relevant to the real world.
Droplet Combustion Experiments Aboard the International Space Station
NASA Astrophysics Data System (ADS)
Dietrich, Daniel L.; Nayagam, Vedha; Hicks, Michael C.; Ferkul, Paul V.; Dryer, Frederick L.; Farouk, Tanvir; Shaw, Benjamin D.; Suh, Hyun Kyu; Choi, Mun Y.; Liu, Yu Cheng; Avedisian, C. Thomas; Williams, Forman A.
2014-10-01
This paper summarizes the first results from isolated droplet combustion experiments performed on the International Space Station (ISS). The long durations of microgravity provided in the ISS enable the measurement of droplet and flame histories over an unprecedented range of conditions. The first experiments were with heptane and methanol as fuels, initial droplet droplet diameters between 1.5 and 5.0 m m, ambient oxygen mole fractions between 0.1 and 0.4, ambient pressures between 0.7 and 3.0 a t m and ambient environments containing oxygen and nitrogen diluted with both carbon dioxide and helium. The experiments show both radiative and diffusive extinction. For both fuels, the flames exhibited pre-extinction flame oscillations during radiative extinction with a frequency of approximately 1 H z. The results revealed that as the ambient oxygen mole fraction was reduced, the diffusive-extinction droplet diameter increased and the radiative-extinction droplet diameter decreased. In between these two limiting extinction conditions, quasi-steady combustion was observed. Another important measurement that is related to spacecraft fire safety is the limiting oxygen index (LOI), the oxygen concentration below which quasi-steady combustion cannot be supported. This is also the ambient oxygen mole fraction for which the radiative and diffusive extinction diameters become equal. For oxygen/nitrogen mixtures, the LOI is 0.12 and 0.15 for methanol and heptane, respectively. The LOI increases to approximately 0.14 (0.14 O 2/0.56 N 2/0.30 C O 2) and 0.17 (0.17 O 2/0.63 N 2/0.20 C O 2) for methanol and heptane, respectively, for ambient environments that simulated dispersing an inert-gas suppressant (carbon dioxide) into a nominally air (1.0 a t m) ambient environment. The LOI is approximately 0.14 and 0.15 for methanol and heptane, respectively, when helium is dispersed into air at 1 atm. The experiments also showed unique burning behavior for large heptane droplets. After the visible hot flame radiatively extinguished around a large heptane droplet, the droplet continued to burn with a cool flame. This phenomena was observed repeatably over a wide range of ambient conditions. These cool flames were invisible to the experiment imaging system but their behavior was inferred by the sustained quasi-steady burning after visible flame extinction. Verification of this new burning regime was established by both theoretical and numerical analysis of the experimental results. These innovative experiments have provided a wealth of new data for improving the understanding of droplet combustion and related aspects of fire safety, as well as offering important measurements that can be used to test sophisticated evolving computational models and theories of droplet combustion.
Pioneering Deans of Women: More Than Wise and Pious Matrons. Athene Series.
ERIC Educational Resources Information Center
Nidiffer, Jana
This book examines the careers and contributions of four pioneering deans of women and the innovations they created as they worked to enhance opportunities and community for women. The women are Marion Talbot, Mary Bidwell Breed, Ada Louise Comstock, and Lois Kimball Mathews. The book analyzes how they developed a profession out of their…
Mechanisms of Twist 1-Induced Invasion in Breast Cancer Metastasis
2011-01-01
with properties of stem cells. Cell 133, 704–715. Miller, L.D., Smeds , J., George, J., Vega, V.B., Vergara, L., Ploner, A., Pawitan, Y., Hall, P...Sotiriou, C., Wirapati, P., Loi, S., Harris, A., Fox, S., Smeds , J., Nordgren, H., Farmer, P., Praz, V., Haibe-Kains, B., et al. (2006). Gene expression
Language and Inequality: Global Challenges to Education
ERIC Educational Resources Information Center
Brock-Utne, Birgit
2012-01-01
This article is an abbreviated version of the BAICE Presidential Address held at the 11th UKFIET International Conference in Oxford on September 16, 2011. It discusses debates on the use of a foreign and ex-colonial language as a language of instruction (LOI) in African schools and argues that the quality of education cannot be seen as an issue…
Doubletalk: A Literary Pairing of "The Giver" and "We Are All in the Dumps with Jack and Guy."
ERIC Educational Resources Information Center
Lehman, Barbara A.; Crook, Patricia R.
1998-01-01
Pairs two books that might stimulate children's literary awareness--Lois Lowry's fantasy novel, "The Giver," and Maurice Sendak's picture book, "We Are All in the Dumps with Jack and Guy." Finds that the pairing and comparisons increased understandings about each work and how complementary they really are. (PA)
2017-03-01
experimental effort involving a series of +z-axis impact tests was conducted on the 711th Human Performance Wing’s Vertical Deceleration Tower (VDT...parameters) and a JSF-styled ejection seat configuration (combined non -baseline test parameters) produced similar biodynamic response parameters for the LOIS...Photography .............................................................................. 12 6.0 EXPERIMENTAL DESIGN
A mixing model derived from first principles describes the bulk density (BD) of intertidal wetland sediments as a function of loss on ignition (LOI). The model assumes the bulk volume of sediment equates to the sum of self-packing volumes of organic and mineral components or BD =...
40 CFR 60.685 - Test methods and procedures.
Code of Federal Regulations, 2014 CFR
2014-07-01
... average of three glass pull rate (Pi) determinations taken at intervals of at least 30 minutes during each run. The individual glass pull rates (Pi) shall be computed using the following equation: Pi = K′ Ls Wm M [1.0−(LOI/100)] where: Pi = glass pull rate at interval “i”, Mg/hr (ton/hr). Ls = line speed, m...
75 FR 81585 - Gulf of Mexico Fishery Management Council; Public Meeting
Federal Register 2010, 2011, 2012, 2013, 2014
2010-12-28
.... SUMMARY: The Gulf of Mexico Fishery Management Council will convene a meeting of the Ad Hoc Reef Fish..., January 25, 2011, and conclude by 4 p.m. ADDRESSES: The meeting will be held at the Gulf of Mexico Fishery... address: Gulf of Mexico Fishery Management Council, 2203 N. Lois Avenue, Suite 1100, Tampa, FL 33607. FOR...
78 FR 12294 - Gulf of Mexico Fishery Management Council (Council); Public Meetings
Federal Register 2010, 2011, 2012, 2013, 2014
2013-02-22
... meetings. SUMMARY: The Gulf of Mexico and South Atlantic Fishery Management Councils will convene a Science.... to 4 p.m. EST on Tuesday, March 12, 2013. ADDRESSES: The meeting will be held at the Gulf of Mexico.... Council address: Gulf of Mexico Fishery Management Council, 2203 North Lois Avenue, Suite 1100, Tampa, FL...
ERIC Educational Resources Information Center
Moore, Janette; Smith, Gillian W.; Shevlin, Mark; O'Neill, Francis A.
2010-01-01
An alternative models framework was used to test three confirmatory factor analytic models for the Short Leyton Obsessional Inventory-Children's Version (Short LOI-CV) in a general population sample of 517 young adolescent twins (11-16 years). A one-factor model as implicit in current classification systems of Obsessive-Compulsive Disorder (OCD),…
Professional Learning Communities by Design: Putting the Learning Back into PLCs
ERIC Educational Resources Information Center
Easton, Lois Brown
2011-01-01
If you are looking for an organic approach to purpose-driven professional learning, this is the book for you. Award-winning educator Lois Brown Easton's latest work provides a compelling case study in narrative form, a chronological PLC planning outline, and first-hand "lessons learned" about how PLCs develop, mature, and sustain themselves. You…
ERIC Educational Resources Information Center
Rural Educator, 2002
2002-01-01
In addition to her "never give up on any student" philosophy, Lois Rodgers has created an integrated, thematic curricular design that uses the brain's methods of transferring knowledge to long-term retention. She collaborates with community members, teachers, and students to improve teaching and learning. Her school is recognized…
ERIC Educational Resources Information Center
Chapman, Luisa Washington
This slide kit presents the diverse stylistic achievements of 15 African-American artists who worked between mid-19th century to present day. Essays included in the packet incorporate information from interviews with artists Hughie Lee-Smith, Elizabeth Catlett, Benny Andrews, Lois Mailou Jones, Allan Rohan Crite, Howardena Pindell, and Jack…
NASA Astrophysics Data System (ADS)
Okonkwo, Chukwuemeka T.; Ganev, Valentin Y.
2018-04-01
The authors regret the error in Table 1-Chemical composition of the orthogneisses where the sum of the elements for each sample was mistakenly indicated as LOI (loss on ignition). The correct table is given below.
Degradation of TBC Systems in Environments Relevant to Advanced Gas Turbines for IGCC Systems
NASA Astrophysics Data System (ADS)
Bohna, Nathaniel Allan
Plasma sprayed (PS) thermal barrier coatings (TBCs) are used to provide thermal insulation for the hottest components in gas turbines. Zirconia stabilized with 7wt% yttria (7YSZ) is the most common ceramic top coat used for turbine blades. The 7YSZ coating can be degraded by the buildup of fly-ash deposits which can arise from the fuel source (coal/biomass) used in the combustion process in gas turbines. Fly-ash from the integrated gasification combined cycle (IGCC) process can result from coal-based syngas and also from ambient air which passes through the system. TBCs are also exposed to harsh gas environments containing CO2, SO2, and steam. As presented in this thesis, degradation from the combined effects of fly-ash and harsh gas atmosphere can severely limit TBC lifetimes. It is well established that degradation at very high temperatures (≥1250°C) from deposits consisting of the oxides CaO-MgO-Al2O3-SiO 2 results from extensive liquid silicate infiltration into the porous top coat of the YSZ. This infiltration causes early failure resulting from chemical and/or mechanical damage to the ceramic layer. Damage resulting from liquid infiltration, however, is not typically considered at relatively lower temperatures around 1100°C because liquid silicates would not be expected to form from the oxides in the deposit. A key focus of this study is to assess the mode and extent of TBC degradation at 1100°C in cases when some amount of liquid forms owing to the presence of K2SO4 as a minor ash constituent. Two types of liquid infiltrations are observed depending on the principal oxide (i.e., CaO or SiO2) in the deposit. The degradation is primarily the result of mechanical damage, which results from infiltration caused by the interaction of liquid K2SO4 with either the CaO or SiO2. The TBCs used in this work are representative of commonly used coatings used in the hottest sections of land-based gas turbines. The specimens consist of 7YSZ top coats deposited on superalloy (Rene' N5 and PWA 1484) substrates that had been coated with NiCoCrAlY bond coats. Two different top coats are studied: conventional low-density 7YSZ, and also dense vertically cracked coatings. The specific mechanisms of liquid infiltration resulting from CaO and SiO2 are studied by conducting isothermal exposures followed by detailed characterizations. The resulting consequences on cyclic lifetimes are also determined. Further, the cyclic lifetimes are studied in several gas atmospheres to examine the combined effect of deposit and gas atmosphere on TBC lifetime. This work identifies a TBC degradation mechanism which had previously not been considered. It will be clearly shown that deposit-induced attack of TBCs can be highly detrimental at an intermediate temperature like 1100°C.
Al-Masri, M S; Haddad, Kh; Doubal, A W; Awad, I; Al-Khatib, Y
2014-06-01
Soil contamination by (210)Pb and (210)Po around heavy oil and natural gas power plants has been investigated; fly and bottom ash containing enhanced levels of (210)Pb and (210)Po were found to be the main source of surface soil contamination. The results showed that (210)Pb and (210)Po in fly-ash (economizer, superheater) is highly enriched with (210)Pb and (210)Po, while bottom-ash (boiler) is depleted. The highest (210)Pb and (210)Po activity concentrations were found to be in economizer ash, whereas the lowest activity concentration was in the recirculator ash. On the other hand, (210)Pb and (210)Po activity concentrations in soil samples were found to be higher inside the plant site area than those samples collected from surrounding areas. The highest levels were found in the vicinity of Mhardeh and Tishreen power plants; both plants are operated by heavy oil and natural fuels, while the lowest values were found to be in those samples collected from Nasrieh power plant, which is only operated by one type of fuel, viz. natural gas. In addition, the levels of surface soil contamination have decreased as the distance from the power plant site center increased. Copyright © 2014 Elsevier Ltd. All rights reserved.
ERIC Educational Resources Information Center
Vandergrift, Kay E.
1993-01-01
Examines the development of multicultural literature for children and youth in the mid-20th century in the light of feminist theory. Phases of curricular revision are described; and the works of four white women writers, Florence Crannell Means, Ann Nolan Clark, Marguerite de Angeli, and Lois Lenski, are reviewed. (Contains 71 references.) (LRW)
2007-11-01
Florea, Anne-Laure Jousselme, Éloi Bossé ; DRDC Valcartier TR 2003-319 ; R & D pour la défense Canada – Valcartier ; novembre 2007. Contexte : Pour...12 3.3.2 Imprecise information . . . . . . . . . . . . . . . . . . . . . 13 3.3.3 Uncertain and imprecise information...information proposed by Philippe Smets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 5: The process of information modelling
ERIC Educational Resources Information Center
Hunter, Jevon D.; Silvestri, Katarina N.; Ackerman, Madison L.
2018-01-01
This article shares the qualitative research findings of an emerging professional development schools partnership that investigated the way Twitter, as a type of digital literacy, mediated literature discussions of Lois Lowry's "The Giver" between urban high school students and master's degree literacy specialist candidates. The findings…
ERIC Educational Resources Information Center
National Council of Teachers of English, Champaign, IL.
The 13 articles in this report fall into four categories: programs for the culturally disadvantaged, teaching composition, curriculum revision, and detailed classroom practices. Mildred A. Dawson outlines compensatory programs used in Sacramento, California, to prevent drop-outs; Lois Grose concentrates on the pattern-practice method of teaching…
Protocol Development | Division of Cancer Prevention
The chemoprevention Phase I and II consortia must submit Letters of Intent for review and approval prior to the submission and review of the protocol. Letter of Intent (LOI) Process The chemoprevention Phase I and II consortia must submit Letters of Intent for review and approval prior to the submission and review of the protocol. DCP will solicit Letters of Intent from
From Matron to Maven: A New Role and New Professional Identity for Deans of Women, 1892 to 1916.
ERIC Educational Resources Information Center
Nidiffer, Jana
1995-01-01
Traces the careers of four women who were instrumental in transforming the position of dean of women from dormitory matron into professional administrator. These women were Marion Talbot, University of Chicago, 1892-1925; Mary Bidwell Breed, Indiana University, 1901-06; Ada Louise Comstock, University of Minnesota, 1906-12; and Lois Kimball…
40 CFR 60.685 - Test methods and procedures.
Code of Federal Regulations, 2013 CFR
2013-07-01
... average of three glass pull rate (Pi) determinations taken at intervals of at least 30 minutes during each run. The individual glass pull rates (Pi) shall be computed using the following equation: Pi=K′ Ls Wm M [1.0−(LOI/100)] where: Pi=glass pull rate at interval “i”, Mg/hr (ton/hr). Ls=line speed, m/min...
40 CFR 60.685 - Test methods and procedures.
Code of Federal Regulations, 2012 CFR
2012-07-01
... average of three glass pull rate (Pi) determinations taken at intervals of at least 30 minutes during each run. The individual glass pull rates (Pi) shall be computed using the following equation: Pi=K′ Ls Wm M [1.0−(LOI/100)] where: Pi=glass pull rate at interval “i”, Mg/hr (ton/hr). Ls=line speed, m/min...
Federal Judge Rules against Faculty Union on Refunds of Nonmembers' Dues
ERIC Educational Resources Information Center
Glenn, David
2008-01-01
The faculty union at the City University of New York must make it easier for nonmembers to receive refunds of union dues spent on activities other than collective bargaining, a federal judge ruled this month. Magistrate Judge Lois Bloom, of the U.S. District Court in Brooklyn, found that the union, the Professional Staff Congress (or PSC),…
40 CFR 60.685 - Test methods and procedures.
Code of Federal Regulations, 2011 CFR
2011-07-01
... average of three glass pull rate (Pi) determinations taken at intervals of at least 30 minutes during each run. The individual glass pull rates (Pi) shall be computed using the following equation: Pi=K′ Ls Wm M [1.0−(LOI/100)] where: Pi=glass pull rate at interval “i”, Mg/hr (ton/hr). Ls=line speed, m/min...
40 CFR 60.685 - Test methods and procedures.
Code of Federal Regulations, 2010 CFR
2010-07-01
... average of three glass pull rate (Pi) determinations taken at intervals of at least 30 minutes during each run. The individual glass pull rates (Pi) shall be computed using the following equation: Pi=K′ Ls Wm M [1.0−(LOI/100)] where: Pi=glass pull rate at interval “i”, Mg/hr (ton/hr). Ls=line speed, m/min...
ERIC Educational Resources Information Center
2002
The Public Relations Division of the proceedings contains the following 15 papers: "Virtual Issues in Traditional Texts: How Introductory Public Relations Textbooks Address Internet Technology Issues" (Lois A. Boynton and Cassandra Imfeld Gajkowski); "Crisis Public Relations: A Study of Leadership, Culture, Demand and Delivery"…
The New Language of Instruction Policy in Malawi: A House Standing on a Shaky Foundation
ERIC Educational Resources Information Center
Kamwendo, Gregory Hankoni
2016-01-01
This research note is a critique of Malawi's new language of instruction (LOI) policy. The new policy stipulates English as the medium of instruction from the first year (Standard 1) of primary school in a country where English is not the dominant language of household communication. The children are now expected to learn (and that includes…
ERIC Educational Resources Information Center
Van Laere, E.; Braak, J.
2017-01-01
Text-to-speech technology can act as an important support tool in computer-based learning environments (CBLEs) as it provides auditory input, next to on-screen text. Particularly for students who use a language at home other than the language of instruction (LOI) applied at school, text-to-speech can be useful. The CBLE E-Validiv offers content in…
ERIC Educational Resources Information Center
Department of Supply and Services, Ottawa (Ontario).
The Canadian Human Rights Act extends the laws in Canada that proscribe discrimination by establishing that each individual has the right to make the life for him- or herself that he or she is able and wishes to have, consistent with the duties and obligations of a member of society, without being hindered or prevented from doing so by…
The Oral History of Evaluation Part II: The Professional Development of Lois-ellin Datta
ERIC Educational Resources Information Center
Miller, Robin; King, Jean; Mark, Melvin; Stockdill, Stacey
2004-01-01
In early 2002, Jean King, Mel Mark, Robin Miller, and Stacey Stockdill began a project to conduct oral history interviews with individuals who have made signal contributions to the program evaluation field and those well-placed observers who were present at and played a role in pivotal moments in the field. In developing this project, it is our…
ERIC Educational Resources Information Center
Beatty, Barbara
2009-01-01
In 1927, nursery school educator Lucy Sprague Mitchell heralded Jean Piaget's psychology as of "outstanding interest" and wrote in "Progressive Education" that it should be of "immense service" to psychologists, teachers, and parents. In 1929, psychologist Lois Meek praised Piaget's research in the National Society for the Study of Education's…
Human Factors Engineering #3 Crewstation Assessment for the OH-58F Helicopter
2014-03-01
Additionally, workload was assessed for level of interoperability 2 (LOI 2) tasks that the aircrew performed with an unmanned aircraft system (UAS...TTP tactics, techniques, and procedures UAS unmanned aircraft system 47 VFR visual flight rules VMC visual meteorological conditions VTR...For example, pilots often perform navigation tasks, communicate via multiple radios, monitor aircraft systems , and assist the pilot on the controls
Astuti, D; Latif, F; Wagner, K; Gentle, D; Cooper, W N; Catchpoole, D; Grundy, R; Ferguson-Smith, A C; Maher, E R
2005-01-01
Epigenetic alterations in the 11p15.5 imprinted gene cluster are frequent in human cancers and are associated with disordered imprinting of insulin-like growth factor (IGF)2 and H19. Recently, an imprinted gene cluster at 14q32 has been defined and includes two closely linked but reciprocally imprinted genes, DLK1 and GTL2, that have similarities to IGF2 and H19, respectively. Both GTL2 and H19 are maternally expressed RNAs with no protein product and display paternal allele promoter region methylation, and DLK1 and IGF2 are both paternally expressed. To determine whether methylation alterations within the 14q32 imprinted domain occur in human tumorigenesis, we investigated the status of the GTL2 promoter differentially methylated region (DMR) in 20 neuroblastoma tumours, 20 phaeochromocytomas and, 40 Wilms' tumours. Hypermethylation of the GTL2 promoter DMR was detected in 25% of neuroblastomas, 10% of phaeochromocytoma and 2.5% of Wilms' tumours. Tumours with GTL2 promoter DMR hypermethylation also demonstrated hypermethylation at an upstream intergenic DMR thought to represent a germline imprinting control element. Analysis of neuroblastoma cell lines revealed that GTL2 DMR hypermethylation was associated with transcriptional repression of GTL2. These epigenetic findings are similar to those reported in Wilms' tumours in which H19 repression and DMR hypermethylation is associated with loss of imprinting (LOI, biallelic expression) of IGF2. However, a neuroblastoma cell line with hypermethylation of the GTL2 promoter and intergenic DMR did not show LOI of DLK1 and although treatment with a demethylating agent restored GTL2 expression and reduced DLK1 expression. As described for IGF2/H19, epigenetic changes at DLK1/GTL2 occur in human cancers. However, these changes are not associated with DLK1 LOI highlighting differences in the imprinting control mechanisms operating in the IGF2-H19 and DLK1-GTL2 domains. GTL2 promoter and intergenic DMR hypermethylation is associated with the loss of GTL2 expression and this may contribute to tumorigenesis in a subset of human cancers. PMID:15798773
Hajizadeh, Yaghoub; Onwudili, Jude A; Williams, Paul T
2011-06-01
The application of activated carbons has become a commonly used emission control protocol for the removal or adsorption of persistent organic pollutants from the flue gas streams of waste incinerators. In this study, the 2378-substituted PCDD/F removal efficiency of three types of activated carbons derived from the pyrolysis of refuse derived fuel, textile waste and scrap tyre was investigated and compared with that of a commercial carbon. Experiments were carried out in a laboratory scale fixed-bed reactor under a simulated flue gas at 275°C with a reaction period of four days. The PCDD/F in the solid matrices and exhaust gas, were analyzed using gas chromatography coupled with a triple quadrupole mass spectrometer. In the absence of activated carbon adsorbent, there was a significant increase in the concentration of toxic PCDD/F produced in the reacted flyash, reaching up to 6.6 times higher than in the raw flyash. In addition, there was a substantial release of PCDD/F into the gas phase, which was found in the flue gas trapping system. By application of the different commercial, refuse derived fuel, textile and tyre activated carbons the total PCDD/F toxic equivalent removal efficiencies in the exhaust gas stream were 58%, 57%, 64% and 52%, respectively. In general, the removal of the PCDDs was much higher with an average of 85% compared to PCDFs at 41%. Analysis of the reacted activated carbons showed that there was some formation of PCDD/F, for instance, a total of 60.6 μg I-TEQ kg(-1) toxic PCDD/F was formed in the refuse derived fuel activated carbon compared to 34 μg I-TEQ kg(-1) in the commercial activated carbon. The activated carbons derived from the pyrolysis of waste, therefore, showed good potential as a control material for PCDD/F emissions in waste incinerator flue gases. Copyright © 2011 Elsevier Ltd. All rights reserved.
Petrogenesis of pillow basalts from Baolai in southwestern Taiwan
NASA Astrophysics Data System (ADS)
Liu, Chih-Chun; Yang, Huai-Jen
2016-04-01
The pillow basalts from Baolai in southwestern Taiwan have been inferred to bear Dupal signautres based on their Th/Ce ratio, linking the Baolai basalts to the South China Sea (SCS) seamounts that are characterized by Dupal Pb isotope signatures (Smith and Lewis, 2007). In this study, thirty-two Baolai basalt samples were analyzed for abundances of major and trace elements as well as Pb and Nd isotope ratios to verify their Dupal characters and to constrain their petrogenesis significance. The Baolai basalts contain 4-10 % L.O.I.. Three stages of alteration are inferred from plots of L.O.I. abundance versus concentrations major oxides as well as mineral textures and compositions. The first alteration stage was characterized by albitization that converted Ca-rich plagioclase to albite. The second alteration stage was dominated by chloritization of olivine and augite, resulting in increases in L.O.I. abundance. The last alteration stage is represented by formation of secondary calcite in vesicles and cracks. These alteration processes reflect interaction with seawater and apparently did not affect the magmatic Pb isotope composition for the low Pb concentration in seawater. Relative to the North Hemisphere Reference Line (NHRL), the Baolai pillow basalts have higher 208Pb/204Pb ratios at a given 206Pb/204Pb value, showing Dupal anomaly. For their relatively higher 208Pb/204Pb, 207Pb/204Pb, and 206Pb/204Pb ratios, the Baolai basalts are distinct from majority of the Cenozoic basalts in the Hainan-Leizhou peninsula, the Indochina peninsula, and the SCS seamounts, for which derivation from the Hainan mantle plume has been recently proposed (Wang et al., 2013). In contrast, the Baolai basalts and the Cenozoic basalts from eastern Guangdong at southeastern China have similar Pb and Nd isotope compositions, indicating derivation from similar mantle sources. However, the Baolai basalts have lower abundance ratios of Zr/Hf (40.3-45.6 versus 46.5-50.5), La/Yb (12.9-21.0 versus 26.0-33.5), and Dy/Yb (~2.7 versus 2.97-3.62) with higher Lu/Hf (~0.056 versus ~0.045). Based on model calculations, the eastern Guangdong basalts represent mixtures containing large proportions (> 90%) of melt generated by < 2% melting from a source with residual garnet and small proportions (< 10%) of low degree melts (< 1%) from spinel lherzolite. The Baolai basalts are explained as involving higher proportions (10-20%) of melt from spinel lherzolite by higher degrees (2-3%) of partial melting. The unusually high Nb/La ratio of > 1.6 in the Baolai basalts is best explained as reflecting a component in the recycled dehydrated residues, indicating derivation from asthenospheric mantle source that involves subduction components. It is inferred that the subduction components are associated with the subduction of paleo-Pacific Ocean. If this is the case, a relatively high mantle circulation rate (i.e., 1 cm/yr; Wang et al., 2013) is required. Smith and Lewis (2007), International Geology Review 49, 1-13. Wang et al. (2013), Earth and Planetary Science Letters 377-378, 248-259.
Effect of time on dyeing wastewater treatment
NASA Astrophysics Data System (ADS)
Ye, Tingjin; Chen, Xin; Xu, Zizhen; Chen, Xiaogang; Shi, Liang; He, Lingfeng; Zhang, Yongli
2018-03-01
The preparation of carboxymethylchitosan wrapping fly-ash adsorbent using high temperature activated fly ash and sodium carboxymethyl chitosan (CWF), as with the iron-carbon micro-electrolysis process simulation and actual printing and dyeing wastewater. The effects of mixing time and static time on decolorization ratio, COD removing rate and turbidness removing rate were investigated. The experimental results show that the wastewater stirring times on the decolorization rate and COD removal rate and turbidity removal rate influence, with increasing of the stirring time, three showed a downward trend, and reached the peak at 10 min time; wastewater time on the decolorization ratio and COD removing efficiency and turbidness removing rate influence, along with standing time increase, three who declined and reached the maximum in 30min time.
Air pollution levels reflected in deposits on building stone
NASA Astrophysics Data System (ADS)
Nord, Anders G.; Svärdh, Anna; Tronner, Kate
About 1400 samples of building stone have been collected in Sweden and other European countries, mainly from polluted areas but also from countryside districts. All samples have been analysed by SEM/EDS, and some selected by other techniques like XRPD, GC/MS, or ICP. In particular, we have determined concentrations of gypsum, iron and some other metals; chlorine, phosphorus, soot (carbon), and organic components. The results confirm a positive correlation between SO 2 concentrations and gypsum formation on calcareous stone. Polluted areas generate more metal particles and particles of soot, asphalt, car-tyre rubber, fly-ash, quartz, calcite, gypsum, and chlorides. On building façades in polluted cities about 100 constituents have been identified, including carcinogeneous organic compounds like benzopyrene.
Leaching behaviour of coal-ash: a case study.
Hajarnavis, M R; Bhide, A D
2003-10-01
Leaching of trace elements from fly ash dumps to subsoil layer due to the rain water results in contamination of ground water. The ground water pollution due to fly ash deposition on land so occurring was assessed by simulating the disposal site conditions using two lysimeter with two different soils. Leachate was collected and analysed daily to help understand the phenomenon of leaching of fly-ash constituents in the environment. The trace metals and physico-chemical parameters of fly ash and soil used were measured before and after the experiment. Results of analysis of soil and fly ash samples were then compared with the results of lysimeter-I and lysimeter-II. The study reveals that metals respond differently at dumping site while reacting with soil and water.
Civilian End Strength Study. Study Sponsor ODCSLOG.
1985-12-30
Chief of Staff deferred action on the recommendations and requested a subsequent briefing with the following guidance. (1) Need to do more to take...Term Actions ... ..................... 38-39 ix CIVILIAN END STRENGTH STUDY Abstract This study examined the methodology by which the Army determines...DAPE-MBC) and COA ( DACA -OMP) has facilitated this process; an updated LOI, in draft, will clear up some of the problems identified in the test
Annual Progress Report for July 1, 1981 through June 30, 1982,
1982-08-01
Online Search Service .....................93 14.5 Database Analyses ......................................... 0000093 14.6 Automatic Detection of...D. Dow, "Deformatio potentials of "uperlattices and Interfaces, L. at Vsaunm Sienc Ma Tchnolly. vol. 19, pp. $64-566, 1981. 4.17 3. D. Oberstar, No...cince, vol. 15, no. 3, pp. 311-320, Sept. 1981. 12.11 M. C. Loi, "Simulations among multidimensional Turing machines," Theoretilna Comanaz Sience (to
2013-01-01
proposed acquisition of a variety of armoured vehicle simulators for training within the Canadian Forces. The Directorate of Land Requirements (DLR... armoured vehicle operations under the Land Vehicle Crew Training System (LVCTS) project. DLR has published a Letter of Interest (LOI) to solicit input...LVCTS project staff to discuss the intent of the project. Qualification Standards and Training Plans for several military armoured vehicle
40 CFR Appendix B to Subpart Hhhh... - Method for the Determination of Loss-on-Ignition
Code of Federal Regulations, 2014 CFR
2014-07-01
... mat. 4.5Weigh the empty crucible to the nearest 0.001 g. Record this weight as the tare mass, T. 4...-Formed Fiberglass Mat Production Pt. 63, Subpt. HHHH, App. B Appendix B to Subpart HHHH of Part 63—Method...-on-ignition (LOI) of wet-formed fiberglass mat. 2.0Equipment 2.1 Scale sensitive to 0.001 gram (g). 2...
40 CFR Appendix B to Subpart Hhhh... - Method for the Determination of Loss-on-Ignition
Code of Federal Regulations, 2012 CFR
2012-07-01
... mat. 4.5Weigh the empty crucible to the nearest 0.001 g. Record this weight as the tare mass, T. 4...-Formed Fiberglass Mat Production Pt. 63, Subpt. HHHH, App. B Appendix B to Subpart HHHH of Part 63—Method...-on-ignition (LOI) of wet-formed fiberglass mat. 2.0Equipment 2.1 Scale sensitive to 0.001 gram (g). 2...
ERIC Educational Resources Information Center
Association for Education in Journalism and Mass Communication.
The Status of Women section of the Proceedings contains the following 8 papers: "Coverage of Mars Exploration: Media Messages about Women Scientists" (Karon R. Speckman and Lois A. Bichler); "The Case of President Clinton and the Feminists: Discourses of Feminism in the News" (Dustin Harp); "Liberal Feminist Theory and…
Area Handbook Series: Zaire: A Country Study
1993-12-01
minister; colonial government promulgates Loi Fondamentale (Fun- damental Law) to guide nation to independence and to serve as first constitution. June...followed in the wake of the slave trade, by the subsequent improvement in the capacity of Africans to des- troy each other through the use of firearms, and...in rural administration. The most noteworthy involved the establish- ment of rural councils (conseils de secteur ), whose members were to be appointed
1985-03-01
ability to use high technology and the ability to learn new technology as it develops. Soldiers need more than training. They need enough education to...WORK UNIT NUMBERS Florida State Universi ty Center for Educational Technology Tallahassee, FL 32306 2Q263743A794 11. CONTROLLING OFFICE NAME AND...7 - 7 7 7. * Research Note 85-46 Job Skills Education Program: Phase I Report Robert K. Branson I Florida State University * 01 and Lois Wison
Li, Yong; Jing, Haoqing; Zainal Abidin, Ilham Mukriz; Yan, Bei
2017-01-01
Coated conductive structures are widely adopted in such engineering fields as aerospace, nuclear energy, etc. The hostile and corrosive environment leaves in-service coated conductive structures vulnerable to Hidden Material Degradation (HMD) occurring under the protection coating. It is highly demanded that HMD can be non-intrusively assessed using non-destructive evaluation techniques. In light of the advantages of Gradient-field Pulsed Eddy Current technique (GPEC) over other non-destructive evaluation methods in corrosion evaluation, in this paper the GPEC probe for quantitative evaluation of HMD is intensively investigated. Closed-form expressions of GPEC responses to HMD are formulated via analytical modeling. The Lift-off Invariance (LOI) in GPEC signals, which makes the HMD evaluation immune to the variation in thickness of the protection coating, is introduced and analyzed through simulations involving HMD with variable depths and conductivities. A fast inverse method employing magnitude and time of the LOI point in GPEC signals for simultaneously evaluating the conductivity and thickness of HMD region is proposed, and subsequently verified by finite element modeling and experiments. It has been found from the results that along with the proposed inverse method the GPEC probe is applicable to evaluation of HMD in coated conductive structures without much loss in accuracy. PMID:28441328
Temperament features in adolescents with ego-syntonic or ego-dystonic obsessive-compulsive symptoms.
Marchesi, Carlo; Ampollini, Paolo; DePanfilis, Chiara; Maggini, Carlo
2008-09-01
The present study evaluated whether different patterns of temperament may predict a different threshold of acceptability of obsessive-compulsive (OC) symptoms in adolescents. OC symptomatology was detected with the Leyton Obsessional Inventory-Child Version (LOI-CV) and temperament was assessed using the tridimensional personality questionnaire in 2,775 high-school students. According to the LOI-CV scores, the adolescents were classified as high interference (interfering, ego-dystonic symptoms) (HI), supernormal (noninterfering, ego-syntonic symptoms) (Sn) and controls (C) HI were 119 (4.3%), Sn 85 (3.1%) and C 2,571 (92.6%). The best predictor of belonging to HI or Sn groups was the temperament configuration of high Harm Avoidance (HA) and high Persistence (P). The feature that mainly distinguishes the two symptomatic groups were Novelty Seeking (NS) levels. Our data suggest that people characterized by pessimistic worry in anticipation of future problems, passive avoidant behaviour, rapid fatigability (high HA) and irresoluteness, ambitiousness, perseverance, perfectionism, enduring feelings of frustration (high P) might develop OC symptoms. Whether OC symptoms become ego-syntonic or ego-dystonic seems to mainly depend on NS levels: low NS might protect people (with the prevention of "exploratory and active behaviours" that may elicit loss of control on symptoms) from the development of interfering OC symptoms.
A Comparative Study of Obsessionality in Medical Students, Law Students, and Controls.
Harries, Michael D; Kim, Suck Won; Grant, Jon E
2017-09-01
Understanding obsessive-compulsive behavior in medical students and law students is necessary for administrators and educators to properly work with students struggling with obsessionality. We aim to compare the differences in obsessive symptoms between medical students, law students and a control population. A total of 100 third-year medical students, 102 third-year law students and 103 control subjects drawn from the general population completed the Leyton Obsessional Inventory (LOI). Subjects were examined on all three sections (symptoms/traits, resistance and interference) of the LOI. Obsessional symptom scores for medical students (14.29 ± 7.33) and law students (13.65 ± 6.61) were significantly greater than for the control group (11.58 ± 7.45). Medical and law students were both more likely to report checking, order, routine and attention to detail as obsessive symptoms. Medical students were more likely than law students to possess the obsessive symptoms of cleanliness and conscientiousness, while law students were more likely than medical students to possess obsessive symptoms related to difficulty in making up their mind and doubting themselves. While medical students and law students are more obsessional than the control population, each group is more likely to report different obsessive symptoms.
Li, Yong; Jing, Haoqing; Zainal Abidin, Ilham Mukriz; Yan, Bei
2017-04-25
Coated conductive structures are widely adopted in such engineering fields as aerospace, nuclear energy, etc. The hostile and corrosive environment leaves in-service coated conductive structures vulnerable to Hidden Material Degradation (HMD) occurring under the protection coating. It is highly demanded that HMD can be non-intrusively assessed using non-destructive evaluation techniques. In light of the advantages of Gradient-field Pulsed Eddy Current technique (GPEC) over other non-destructive evaluation methods in corrosion evaluation, in this paper the GPEC probe for quantitative evaluation of HMD is intensively investigated. Closed-form expressions of GPEC responses to HMD are formulated via analytical modeling. The Lift-off Invariance (LOI) in GPEC signals, which makes the HMD evaluation immune to the variation in thickness of the protection coating, is introduced and analyzed through simulations involving HMD with variable depths and conductivities. A fast inverse method employing magnitude and time of the LOI point in GPEC signals for simultaneously evaluating the conductivity and thickness of HMD region is proposed, and subsequently verified by finite element modeling and experiments. It has been found from the results that along with the proposed inverse method the GPEC probe is applicable to evaluation of HMD in coated conductive structures without much loss in accuracy.
Loss of motor unit size and quadriceps strength over 10 years in post-polio syndrome.
Bickerstaffe, A; van Dijk, J P; Beelen, A; Zwarts, M J; Nollet, F
2014-06-01
To investigate whether strength decline in post-polio syndrome (PPS) results from excessive distal axonal degeneration of enlarged motor units. We assessed changes over 10 years in isometric quadriceps strength, mean motor unit action potential (MUAP) size, root mean squared (RMS) amplitude, and level of interference (LOI) in 47 patients with PPS and 12 healthy controls, using high density surface EMG. At baseline, all patients had symptomatic quadriceps dysfunction, evidenced by transmission defects on single-fibre EMG. MU size and strength declined significantly by 20% and 15%, respectively in patients with PPS. Those with the largest initial MU sizes exhibited the greatest losses of mean MU size (27%) and proportional decreases in quadriceps strength (23%). Initial strength, change in LOI and change in RMS amplitude together explained 35% of the variability in strength changes in patients. MU size of controls did not change, although they lost 29% strength. MU size and strength declined concomitantly in a homogeneous cohort of patients with PPS and quadriceps dysfunction. This long term follow-up study provides evidence that size diminution of enlarged MUs combined with a reduced number of active MUs contributes to the gradual strength decline in PPS. Copyright © 2013 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.
STS-28 crewmembers' wives at KSC shuttle landing facility (SLF) with banner
1989-08-05
STS028-S-009 (5 Aug 1989) --- Wives of the STS-28 crewmembers display a banner upon the arrival of the astronauts in Florida to begin preparing for their Aug. 8 launch. Left to right are Susan Adamson, Kathleen Ann Shaw, Lynne A. Brown, Lois Richards and Patti K. Leestma. The banner reads, "Go Columbia, STS-28." Launch for the Department of Defense (DOD)-devoted mission is scheduled for August 8.
1988-08-31
C27 A entrevista esclareceu sobre os principals problemas do pais? (3) Cavaco justificou bem as medidas tomadaspeloGoverno? (4) fc 5) . M e...do. My personal wishes did not lie in returning to 16 rue de la loi [prime minister’s residence]. [Question] It was not psychologically very astute...Spokesman on Role in Opposition 36190009 Brussels LA LIBRE BELGIQUE in French 14/15 May 88 p 4 [Interview with Jose Daras, head of the ECOLO- AGALEV
De Almeida, Gilberto De Souza Soares; Loiácono, Marta Susana; Margaría, Cecilia Beatriz; Monteiro, Ricardo Ferreira
2015-07-17
Telenomus parides Loiácono et Margaría sp. nov., is described and illustrated based on specimens reared from the eggs of Parides ascanius (Cramer). Parides ascanius is a threatened papilionid, which is endemic to the restingas of the Atlantic Forest of Rio de Janeiro, Brazil. The new Telenomus species is gregarious endoparasitoid and belongs to the Telenomus californicus species complex.
1987-08-13
ministers. The cease-fire was announced on the French-speaking side of the Rue des Deux- Eglises, where the Social Christian Party has its...entitled "Tintin on the Rue de la Loi." Having reached the top level in the hierarchy of French-speaking Social Christian ministers, he is uncomfortable...partners. The ups and downs of recent weeks have done him harm, and it said that he dreams of distancing himself somewhat. If only Willy De Clercq were
Rebel Integration in Conflict Settlements: Past Lessons and the Prospects of MILF Reintegration
2017-12-01
ethnicity, religion, or language among a nation’s citizens.33 A series of investigations on case studies conducted by Matthew Hoddie and Caroline Hartzell...rebel reintegration from previous peace agreements was consulted. The selected case studies center on the peace agreements in Zimbabwe, Rwanda...Dayton.” 85 Akyol. 86 David Wage and Lois Haigh, “A Case Study on the Arusha Peace Agreement” (Florida State University, July 19, 2004), http
Evaluation of the Impacts of Live Fire Training at CFB Shilo
2003-04-22
des activites d’entrainement faites au secteur d’entrainement de la BFC Shilo et est la suite de la phase I, effectuee en septembre 2000. Durant la...premiere phase, trois champs de bataille avaient ete echantillonnes pour evaluer la contamination par les explosifs, les metaux, les COVs et les...iv Sommaire Le contexte international de demilitarisation, de la fermeture de bases et de la severite croissante des lois environnementales a
Military Aviation Fluids and Lubricants Workshop 2006 (Postprint)
2006-06-01
Blended in Oil at 1-3 Wt. % Reacts Readily With Current Bearing Steels ( M50 , etc.) Does Not React Easily With Stainless Bearing Steels Other...Additives for Advanced Bearing Steel , Lois Gschwender, AFRL 1530 – 1550 New and Innovative Gas turbine Engine Oil Additive Technology, Rich Sapienza/Bill...Selected corrosion- prone, 52100 steel tapered bearings - Timken Bearing Co.- and used F-16 pump pistons in jar storage – Submerged parts • Two water
1989-05-01
The environmental consequences of the proposed deployment of Second KC-135R I AREFS were evaluated in terms of the magnitude and significance of...A for more details). The LOI and significance of short and long-duration impacts were evaluated separately. Short duration impacts are transitory...factors evaluated . n Public Finance. The public finance element describes the fiscal condition of the affected counties, cities, and school districts
2010-10-18
NICK N ESTERUK JACK KELLEY TOM B RASWELL U.S. Army Research Laboratory Aberdeen Proving Ground, Maryland October 18, 2010 Approved for public ...release; distribution is unlimited. REPORT DOCUMENTATION PAGE Form Approved OMS No. 0704-0188 PUblIC reporting DUrClen lOr lOIS COIlBC\\lOn... public release; distribution is unlimited. 13. SUPPLEMENTARY NOTES ·Science Applications International Corporation (SAIC), 4555 Overlook Ave, SW, Bldg
DOE Office of Scientific and Technical Information (OSTI.GOV)
Michael D. Durham
PG&E NEG Salem Harbor Station Unit 1 was successfully tested for applicability of activated carbon injection as a mercury control technology. Test results from this site have enabled a thorough evaluation of mercury control at Salem Harbor Unit 1, including performance, estimated cost, and operation data. This unit has very high native mercury removal, thus it was important to understand the impacts of process variables on native mercury capture. The team responsible for executing this program included plant and PG&E headquarters personnel, EPRI and several of its member companies, DOE, ADA, Norit Americas, Inc., Hamon Research-Cottrell, Apogee Scientific, TRC Environmentalmore » Corporation, Reaction Engineering, as well as other laboratories. The technical support of all of these entities came together to make this program achieve its goals. Overall the objectives of this field test program were to determine the mercury control and balance-of-plant impacts resulting from activated carbon injection into a full-scale ESP on Salem Harbor Unit 1, a low sulfur bituminous-coal-fired 86 MW unit. It was also important to understand the impacts of process variables on native mercury removal (>85%). One half of the gas stream was used for these tests, or 43 MWe. Activated carbon, DARCO FGD supplied by NORIT Americas, was injected upstream of the cold side ESP, just downstream of the air preheater. This allowed for approximately 1.5 seconds residence time in the duct before entering the ESP. Conditions tested in this field evaluation included the impacts of the Selective Non-Catalytic Reduction (SNCR) system on mercury capture, of unburned carbon in the fly ash, of adjusting ESP inlet flue gas temperatures, and of boiler load on mercury control. The field evaluation conducted at Salem Harbor looked at several sorbent injection concentrations at several flue gas temperatures. It was noted that at the mid temperature range of 322-327 F, the LOI (unburned carbon) lost some of its ability to capture vapor phase Hg, however activated carbon performed relatively well. At the normal operating temperatures of 298-306 F, mercury emissions from the ESP were so low that both particulate and elemental mercury were ''not detected'' at the detection limits of the Ontario Hydro method for both baseline and injection tests. The oxidized mercury however, was 95% lower at a sorbent injection concentration of 10 lbs/MMacf compared with baseline emissions. When the flue gas temperatures were increased to a range of 343-347 F, mercury removal efficiencies were limited to <25%, even at the same sorbent injection concentration. Other tests examined the impacts of fly ash LOI, operation of the SNCR system, and flue gas temperature on the native mercury capture without sorbent injection. Listed below are the main conclusions from this program: (1) SNCR on/off test showed no beneficial effect on mercury removal caused by the SNCR system. (2) At standard operating temperatures ({approx} 300 F), reducing LOI from 30-35% to 15-20% had minimal impact on Hg removal. (3) Increasing flue gas temperatures reduced Hg removal regardless of LOI concentrations at Salem Harbor (minimum LOI was 15%). Native mercury removal started to fall off at temperatures above 320 F. ACI effectiveness for mercury removal fell off at temperatures above 340 F. (4) Test method detection limits play an important role at Salem Harbor due to the low residual emissions. Examining the proposed MA rule, both the removal efficiency and the emission concentrations will be difficult to demonstrate on an ongoing basis. (5) Under tested conditions the baseline emissions met the proposed removal efficiency for 2006, but not the proposed emission concentration. ACI can meet the more-stringent 2012 emission limits, as long as measurement detection limits are lower than the Ontario Hydro method. SCEM testing was able to verify the low emissions. For ACI to perform at this level, process conditions need to match those obtained during testing.« less
Examination of contrast mechanisms in optoacoustic imaging of thermal lesions
NASA Astrophysics Data System (ADS)
Richter, Christian; Spirou, Gloria; Oraevsky, Alexander A.; Whelan, William M.; Kolios, Michael C.
2006-02-01
Optoacoustic Imaging is based on the thermal expansion of tissue caused by a temperature rise due to absorption of short laser pulses. At constant laser fluence, optoacoustic image contrast is proportional to differences in optical absorption and the thermoacoustic efficiency, expressed by the Grueuneisen parameter, Γ. Γ is proportional to the thermal expansion coefficient, the sound velocity squared and the inverse heat capacity at constant pressure. In thermal therapies, these parameters may be modified in the treated area. In this work experiments were performed to examine the influence of these parameters on image contrast. A Laser Optoacoustic Imaging System (LOIS, Fairway Medical Technologies, Houston, Texas) was used to image tissue phantoms comprised of cylindrical Polyvinyl Chloride Plastisol (PVCP) optical absorbing targets imbedded in either gelatin or PVCP as the background medium. Varying concentrations of Black Plastic Color (BPC) and titanium dioxide (TiO II) were added to targets and background to yield desired tissue relevant optical absorption and effective scattering coefficients, respectively. In thermal therapy experiments, ex-vivo bovine liver was heated with laser fibres (805nm laser at 5 W for 600s) to create regions of tissue coagulation. Lesions formed in the liver tissue were visible using the LOIS system with reasonable correspondence to the actual region of tissue coagulation. In the phantom experiments, contrast could be seen with low optical absorbing targets (μ a of 0.50cm -1 down to 0.13cm-1) embedded in a gelatin background (see manuscript for formula). Therefore, the data suggest that small objects (< 5mm) with low absorption coefficients (in the range < 1cm -1) can be imaged using LOIS. PVCP-targets in gelatin were visible, even with the same optical properties as the gelatin, but different Γ. The enhanced contrast may also be caused by differences in the mechanical properties between the target and the surrounding medium. PVCP-targets imbedded in PVCP produced poorer image contrast than PVCP-targets in gelatin with comparable optical properties. The preliminary investigation in tissue equivalent phantoms indicates that in addition to tissue optical properties, differences in mechanical properties between heated and unheated tissues may be responsible for image contrast. Furthermore, thermal lesions in liver tissue, ex-vivo, can be visualized using an optoacoustic system.
Frybourg, Sandrine; Remuzat, Cécile; Kornfeld, Åsa; Toumi, Mondher
2015-01-01
The slow reaction of French authorities to the so-called Mediator® saga in 2009 in France led to investigations that questioned the way conflicts of interest are reported. France implemented the Loi Bertrand ('Bertrand Law') in May 2013, known as the 'French Sunshine Act', with the aim of specifying the scope of disclosure obligations. This policy research reviewed the Loi Bertrand and reported case law from the French Council of State (COS) related to conflicts of interest in French Health technology assessment (HTA) opinion. The Loi Bertrand requires the publication of most of the agreements concluded between health-care professionals and companies and covers a vast range of health products. Commercial sales agreements of goods and services concluded between manufacturers and health-care professionals are a strong exception to this disclosure obligation. Six cases examined by the COS were analyzed, most of them related to the publication of guidelines or the removal of products from the list of reimbursed drugs and devices. These cases have been reviewed, as well as the impact of the ruling on reimbursement decisions. Four cases led to suspension or invalidation of decisions based on the Haute Autorité de Santé (HAS) recommendations due to conflicts of interest. In the two other cases, the HAS provided post hoc declarations of interest when required by the COS, and the COS considered the conflicts of interest as irrelevant for the decision. It appears that the COS based its decisions on two main criteria: the acknowledgement of negative conflicts of interest (a link with competitors) and the absence of declarations of conflicts of interest, which have to be presented when required by legal authorities irrespective of when they were completed (even posterior to the HAS opinion). However, the number of cases that have been decided against the HAS remains very limited with respect to the volume of assessments performed yearly. The strengthening of the regulation on declarations of interest might lead to more transparency but also to more cases decided by the COS. A new press investigation (in March 2015) related to alleged cases of conflict of interests led policy makers to amend the Bertrand Law in April 2015 and require the disclosure of amounts paid to health-care professionals by the industry.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Durham, M.D.
The purpose of this research program is to identify and evaluate a variety of additives capable of increasing particle cohesion which could be used for improving collection efficiency in an ESP. A three-phase screening process will be used to provide the, evaluation of many additives in a logical and cost-effective manner. The three step approach involves the following experimental setups: 1. Provide a preliminary screening in the laboratory by measuring the effects of various conditioning agents on reentrainment of flyash particles in an electric field operating at simulated flue gas conditions. 2. Evaluate the successful additives using a 100 acfmmore » bench-scale ESP operating on actual flue gas. 3. Obtain the data required for scaling up the technology by testing the two or three most promising conditioning agents at the pilot scale.« less
2007-01-01
LifeBridge Health developed and implemented an awareness campaign to generate buzz about the breast cancer services at the Alvin & Lois Lapidus Cancer Institute of LifeBridge Health and the Herman & Walter Samuelson Breast Cancer Care Center at Northwest Hospital Center. With the help of talented local breast cancer survivors, celebrities, fashion designers, and artists, LifeBridge Health created a campaign, including an interactive Web site, public relations outreach, and a unique event in October 2006 that featured a collection of hand-made decorated bras.
A Cultural Resources Reconnaissance of Five Projects in Puerto Rico.
1980-01-01
Puerto Rico, Archeology, History, Ethnohistory, Prehistory, COE projects, Rio Puerto Nuevo , Rio Grande de Loiza, Rio Tallaboa, Rio Guanajibo, Rio...results of a 2 week cultural resources reconnaissance of Corps of Engineers projects in Puerto Ricoh Rio Puerto Nuevo , Rio Grande de Loi2a Rio...of Capara a title search of one of the Rio Puerto Nuevo projectO and’informatioI m pson the projects available in the US Army Corps of Engineers San
Patents - An Information Resource.
1980-09-01
11 vs sans dire que ces aspects de description at de divulqation interviennent en plus des trois critbrea classiques de nouveautd, de hauteur...la divulgation doit, nous 1’ avons vu, aux termes de Ia loi , permettre b l’homme de l’art de reconstituer 1’invention. Or on sait bien que lea d...je vous en donnerai confirmation au mayen de r~sultats dletudea conduites au cours de ceo dernibres annies dans diff~rents pays et secteurs
Swedish Defence Research Abstracts 79/80-4 (Froe Foersvars Forsknings Referat 79/80-4).
1980-12-05
wavelength. In order to verify and modify the model, measurements were made with a transmissometer over a horizontal measuring path . The equipment was...wavelength. In order to verify and modify the model, measurements were made with a transmissometer over a horizontal measuring path . The equipment was in... measurements taken from a number of meteoro loi ca I sensors. Aerosol .xtinc tion was obtained by subtracting the water vapour extinction , as calculated trom
ERIC Educational Resources Information Center
Office of Educational Research and Improvement (ED), Washington, DC. Office of Reform Assistance and Dissemination.
These volumes contain working papers related to the development of the Office of Educational Research and Improvement (OERI) Facilitated System of Expert Panels. Introductory papers by Susan Klein, Michael Scriven, Sharon Bobbitt and Susan Klein, and Michael Scriven and Lois-ellin Datta (printed in both volumes) set the stage for the discussions…
Tree cover and species composition effects on academic performance of primary school students.
Sivarajah, Sivajanani; Smith, Sandy M; Thomas, Sean C
2018-01-01
Human exposure to green space and vegetation is widely recognized to result in physical and mental health benefits; however, to date, the specific effects of tree cover, diversity, and species composition on student academic performance have not been investigated. We compiled standardized performance scores in Grades 3 and 6 for the collective student body in 387 schools across the Toronto District School Board (TDSB), and examined variation in relation to tree cover, tree diversity, and tree species composition based on comprehensive inventories of trees on school properties combined with aerial-photo-based assessments of tree cover. Analyses accounted for variation due to socioeconomic factors using the learning opportunity index (LOI), a regional composite index of external challenges to learning that incorporates income and other factors, such as students with English as a second language. As expected, LOI had the greatest influence on student academic performance; however, the proportion of tree cover, as distinct from other types of "green space" such as grass, was found to be a significant positive predictor of student performance, accounting for 13% of the variance explained in a statistical model predicting mean student performance assessments. The effects of tree cover and species composition were most pronounced in schools that showed the highest level of external challenges, suggesting the importance of urban forestry investments in these schools.
Tree cover and species composition effects on academic performance of primary school students
Smith, Sandy M.; Thomas, Sean C.
2018-01-01
Human exposure to green space and vegetation is widely recognized to result in physical and mental health benefits; however, to date, the specific effects of tree cover, diversity, and species composition on student academic performance have not been investigated. We compiled standardized performance scores in Grades 3 and 6 for the collective student body in 387 schools across the Toronto District School Board (TDSB), and examined variation in relation to tree cover, tree diversity, and tree species composition based on comprehensive inventories of trees on school properties combined with aerial-photo-based assessments of tree cover. Analyses accounted for variation due to socioeconomic factors using the learning opportunity index (LOI), a regional composite index of external challenges to learning that incorporates income and other factors, such as students with English as a second language. As expected, LOI had the greatest influence on student academic performance; however, the proportion of tree cover, as distinct from other types of “green space” such as grass, was found to be a significant positive predictor of student performance, accounting for 13% of the variance explained in a statistical model predicting mean student performance assessments. The effects of tree cover and species composition were most pronounced in schools that showed the highest level of external challenges, suggesting the importance of urban forestry investments in these schools. PMID:29474503
NASA Astrophysics Data System (ADS)
Bossavit, A.
1993-03-01
Macroscopic modelling of superconductors demands a substitution of some nonlinear behavior law for Ohm's law. For this, a version of Bean's “critical state” model, derived from the setting of a convex functional of the current density field, valid in dimension 3 without any previous assumption about the direction of currents, is proposed. It is shown how two standard three-dimensional finite element methods (“h-formulation” and “e-formulation”), once fitted with this model, can deal with situations were superconductors are present. La modélisation macroscopique des supraconducteurs suppose le remplacement de la loi d'Ohm par une loi de comportement non linéaire adéquate. On présente à cet effet une version du “modèle de Bean”, ou modèle de l'état critique, basée sur la construction d'une certaine fonctionnelle convexe du champ des densités de courant, qui est valable en dimension 3 sans hypothèses préalables sur la direction des courants. On montre comment adapter deux méthodes standards de calcul de courants de Foucault par élérnents finis en trois dimensions (“en h” et “en e”) à la présence de supraconducteurs, en incorporant ce modèle.
NASA Astrophysics Data System (ADS)
Moureaux, P.; Moto Mpong, S.; Remy, M.; Bouffioux, C.; Lecomte-Beckers, J.; Habraken, A. M.
2002-12-01
la mise au point d'un modèle de simulation de la dernière passe du laminage à chaud du cuivre ne présente à priori pas de problème du point de vue numérique pour un code d'éléments finis non linéaire. La collecte d'informations précises tant sur le procédé industriel que sur le comportement du matériau est par contre une opération non triviale. Cet article présente les diverses méthodes expérimentales mises en œuvre pour caractériser le matériau : essais de compression à chaud, mesures d'analyse thermique différentielle, essais de dilatométrie et de diffusivité. Les méthodes permettant d'identifier les paramètres de la loi élasto-visco-plastique de type Norton-Hoff à partir des essais sont présentées et une analyse bibliographique investigue le problème de la détermination du module de Young à haute température. Tant les hypothèses supplémentaires relatives au procédé et nécessaires au modèle que les résultats finaux sont résumés.
Municipal waste stabilization in a reactor with an integrated active and passive aeration system.
Kasinski, Slawomir; Slota, Monika; Markowski, Michal; Kaminska, Anna
2016-04-01
To test whether an integrated passive and active aeration system could be an effective solution for aerobic decomposition of municipal waste in technical conditions, a full-scale composting reactor was designed. The waste was actively aerated for 5d, passively aerated for 35 d, and then actively aerated for 5d, and the entire composting process was monitored. During the 45-day observation period, changes in the fractional, morphological and physico-chemical characteristics of the waste at the top of the reactor differed from those in the center of the reactor. The fractional and morphological analysis made during the entire process of stabilization, showed the total reduction of organic matter measured of 82 wt% and 86 wt% at the respective depths. The reduction of organic matter calculated using the results of Lost of Ignition (LOI) and Total Organic Carbon (TOC) showed, respectively, 40.51-46.62% organic matter loss at the top and 45.33-53.39% in the center of the reactor. At the end of the process, moisture content, LOI and TOC at the top were 3.29%, 6.10% and 4.13% higher, respectively, than in the center. The results showed that application of passive aeration in larger scale simultaneously allows the thermophilic levels to be maintained during municipal solid waste composting process while not inhibiting microbial activity in the reactor. Copyright © 2016 Elsevier Ltd. All rights reserved.
NASA Astrophysics Data System (ADS)
Lasri, Abdel-Halim
Dans cette recherche-developpement, nous avons concu, developpe et mis a l'essai un simulateur interactif pour favoriser l'apprentissage des lois probabilistes impliqees dans la genetique mendelienne. Cet environnement informatise devra permettre aux etudiants de mener des experiences simulees, utilisant les statistiques et les probebilites comme outils mathematiques pour modeliser le phenomene de la transmission des caracteres hereditaires. L'approche didactique est essentiellement orientee vers l'utilisation des methodes quantitatives impliquees dans l'experimentation des facteurs hereditaires. En incorporant au simulateur le principe de la "Lunette cognitive" de Nonnon (1986), l'etudiant fut place dans une situation ou il a pu synchroniser la perception de la representation iconique (concrete) et symbolique (abstraite) des lois probabilistes de Mendel. A l'aide de cet environnement, nous avons amene l'etudiant a identifier le(s) caractere(s) hereditaire(s) des parents a croiser, a predire les frequences phenotypiques probables de la descendance issue du croisement, a observer les resultats statistiques et leur fluctuation au niveau de l'histogramme des frequences, a comparer ces resultats aux predictions anticipees, a interpreter les donnees et a selectionner en consequence d'autres experiences a realiser. Les etapes de l'approche inductive sont privilegiees du debut a la fin des activites proposees. L'elaboration, du simulateur et des documents d'accompagnement, a ete concue a partir d'une vingtaine de principes directeurs et d'un modele d'action. Ces principes directeurs et le modele d'action decoulent de considerations theoriques psychologiques, didactiques et technologiques. La recherche decrit la structure des differentes parties composant le simulateur. L'architecture de celui-ci est construite autour d'une unite centrale, la "Principale", dont les liens et les ramifications avec les autres unites confere a l'ensemble du simulateur sa souplesse et sa facilite d'utilisation. Le simulateur "Genetique", a l'etat de prototype, et la documentation qui lui est afferente ont ete soumis a deux mises a l'essai: l'une fonctionnelle, l'autre empirique. La mise a l'essai fonctionnelle, menee aupres d'un groupe d'enseignants experts, a permis d'identifier les lacunes du materiel elabore afin de lui apporter les reajustements qui s'imposaient. La mise a l'essai empirique, conduite par un groupe de onze (11) etudiants de niveau secondaire, avait pour but, d'une part, de tester la facilite d'utilisation du simulateur "Genetique" ainsi que les documents d'accompagnement et, d'autre part, de verifier si les participants retiraient des avantages pedagogiques de cet environnement. Trois techniques furent exploitees pour recolter les donnees de la mise a l'essai empirique. L'analyse des resultats a permis de faire un retour critique sur les productions concretes de cette recherche et d'apporter les modifications necessaires tant au simulateur qu'aux documents d'accompagnement. Cette analyse a permis egalement de conclure que notre simulateur interactif favorise une approche inductive permettant aux etudiants de s'approprier les lois probabilistes de Mendel. Enfin, la conclusion degage des pistes de recherches destinees aux etudes ulterieures, plus particulierement celles qui s'interessent a developper des simulateurs, afin d'integrer a ceux-ci des representations concretes et abstraites presentees en temps reel. Les disquettes du simulateur "Genetique" et les documents d'accompagnement sont annexes a la presente recherche.
Characterization of the non-metal fraction of the processed waste printed circuit boards.
Kumar, Amit; Holuszko, Maria E; Janke, Travis
2018-05-01
Electronic waste is one the fastest growing waste streams in the world and waste printed circuit boards (PCB) are the most valuable part of this stream due to the presence of gold, silver, copper, and palladium. The metal present in PCBs is mostly recovered for the market value whereas the nonmetal fractions are often ignored. This research explored the characteristics of the non-metal fraction (NMF) obtained after the processing of milled waste PCBs with a focus on responsible end-of-life solutions, in the form of non-hazardous landfilling or incineration. The NMF was characterized using sizing, assaying, loss on ignition, calorific value measurement, and thermogravimetric analysis (TGA). The result showed that the metal content in the NMF increased with decrease in the particle size for most of the metals except antimony and the result from loss on ignition (LOI) also showed that over 50% of the coarser fraction represented organic matter compared to less than 30% for the finest fraction. The study also showed that after the recovery of metals from the waste PCBs, landfill leaching for most of the metal is reduced below the environmental limits, with lead being the only exception. The lead leachate concentration of 18 mg/L was observed, which requires further treatment prior to landfilling. With an energy value of 16 GJ/t, the NMF could provide high energy recovery if incinerated but 194 mg/kg of hazardous flame retardants present in the NMF might be released if the combustion process is not closely monitored. Copyright © 2018 Elsevier Ltd. All rights reserved.
NASA Astrophysics Data System (ADS)
Xue, Baoxia; Niu, Mei; Yang, Yongzhen; Bai, Jie; Song, Yinghao; Peng, Yun; Liu, Xuguang
2018-03-01
Carbon microspheres (CMSs) as a core material had been coated by two capsule walls: an inorganic material of magnesium hydroxide (MH) as inner shell layer and an organic material of poly (ethylene terephthalate) (PET) as outer shell layer. MH coating CMSs (MCMSs) were fabricated by liquid phase deposition method, then grafted 3-Aminopropyltriethoxysilane (APTS) to obtain the Si-MCMSs. Microencapsulated Si-MCMSs (PMCMSs) was prepared by in situ polymerization method. Morphology structure, dispersion, flame retardant and other properties of PMCMSs have been investigated. A series of PET blends were prepared by melt compounding. The results showed that MH and PET as two layers were coated on CMSs surface with the optimal thickness of about 70 nm. The PMCMSs owned better dispersion in PET matrix. Compared with MCMSs/PET composites, the mechanical property of PMCMSs/PET composites had significantly increased because of the strong interface binding force between PMCMSs and PET matrix. Moreover, PMCMSs was proved to be an effective flame retardant. For PMCMSs/PET with 2 wt% PMCMSs, the limiting oxygen index (LOI) value increased from 21.0% (pristine PET) to 27.2%, and the peak heat release rate (pk-HRR) decreased from 513.22 kW/m2 to 352.14 kW/m2. The decreased smoke production rate (SPR) and total smoke production (TSP) values demonstrated PMCMSs suppressed the smoke production. The increased Fire performance index (FPI) value illustrated PMCMSs significantly reduced the fire risk of PET. Overall, the two capsular walls endowed the PMCMSs/PET composites with good mechanical and flame-retardant properties.
Calibration and Use of Clutter Data for Simulation.
1985-01-01
radiance surrounded by borders of un- known, nonuniform radiance (Fig. 11). Since the telescopes lie above and below the radiometer’s centerline, the...illuminated solely by the nonuniform borders of the images (Fig. 11). (In Fig. l Ithe detectors are num- bered as they have been since Montauk Point. Prior to...L C LiL F-) 0- W /4- F- 00. L- IL x / -- C:.) < > Ca- < Il / 00 LOi Cl) -00 -. Cl) 41 MONTAUK MIDWAVE DETECTOR-ARRAY NONUNIFORM BOTTOM BORDER 161
Analysis of the Binary Euclidean Algorithm
1976-06-01
Probleme de Gauss," Atti del Congresso Internationale dei Matematici 6 (Bologna, 1928), 83-89. Levy [29] Levy, P., "Sur les Lois de Probabilite...r- Report) 11. SUPPL ENEN T A IllY NOTES lt . KEY WOI’IOS ( Continue on revere• ai de II nec:eaeary and Identify by bloc I< number) I 20...easily de - n n duced by differentiation. 3. The Distribution Functions F ’’ LI The following theorem gives the form of F (x) for finite n n
Southeast Asia Report, Vietnam, Tap Chi Cong San, No. 8, August 1984.
1984-10-22
filled with lyricism and romance, an epic. Continuing this direction and style, recent films have taken another step forward, have reached a new level of...rich in lyricism , were compressed but moving, like poetry, and whereas the resistance against the United States for national salvation marked the...in the " Essay on the Vinh Loi Canal," Nguyen Thong displayed his scientific mind by proposing that the canal be narrow and deep so that it could
ERIC Educational Resources Information Center
Elliott, Virginia A., Ed.; Josephs, Lois S., Ed.
Introducing the essays in this publication, Virginia A. Elliott and Lois S. Josephs review the problems of teaching English to the academically talented student. Essays are by (1) Michael F. Shugrue, who surveys, from 1958 through 1968, the achievements of conferences, Curriculum Study Centers, and the Dartmouth Seminar; (2) John Simmons, who…
Restrike Particle Beam Experiments on a Dense Plasma Focus.
1980-11-30
differentially pumped drift tube as shown in Figure 1. However, even the lOI of gas pressure in the drift space is sufficient to establish an equilibrium...pumped drift tube concept are five-fold: 1) Lower energy attenuation of the beam by neutral gas 2) Lower lateral spread of the beam caused by multiple...relatively low gas pressure through the use of a differentially pumped drift tube . The path makes it possible to observe ion energies to considerably lower
Prediction of Aerodynamic Loading
1977-02-01
d~collage et a atterrissage court ou vertical (V/STOL), trois m~thodes thgoriques ont 6t4 d6crites concernant lvaluation de la charge agrodynamique...Aeronautique, No. 44, Mars-Avril 1955, pp. 3-8. 2. Legendret Robert, ŕcoulement subsonique transveral i un secteur angulaire plan," Comptes Renduo, Vol. 2...d’entrde nbtevu dans ces conditions est propos~se ; e~ie est lbas~e coefficient de frottersent Sur des lois a.-sez empirique-. 6tahlieos ý partir de
1978-09-01
classified as wet meadow. k. Tame Grassland Community (limited) - This community is of minor extent and importance in the vicinity of Lake Traverse...purposes of flood control and water conservation, the Lake Traverse-lois de Sioux flood control project began operation in 1941. It con- sists of two...reservoir pools--Lake Traverse and Mud Lake--plus 24 miles of channel improvement. Several consepts are recoiended for future development of the
ERIC Educational Resources Information Center
Ribordy, Francois-Xavier; And Others
A study investigated the readability of current laws for Canadian francophones and anglophones. The 63 subjects were asked to read a variety of brief legal texts available in parallel styles in both languages and to answer questions about the texts' content. Subjects were also surveyed about their preference for a formal or vulgarized style of…
NASA Astrophysics Data System (ADS)
Wilson, L. G.; Matlock, W. G.; Jacobs, K. L.
The 1995 Water Consumer Protection Act of Tucson, Arizona, USA (hereafter known as the Act) was passed following complaints from Tucson Water customers receiving treated Central Arizona Project (CAP) water. Consequences of the Act demonstrate the uncertainties and difficulties that arise when the public is asked to vote on a highly technical issue. The recharge requirements of the Act neglect hydrogeological uncertainties because of confusion between "infiltration" and "recharge." Thus, the Act implies that infiltration in stream channels along the Central Wellfield will promote recharge in the Central Wellfield. In fact, permeability differences between channel alluvium and underlying basin-fill deposits may lead to subjacent outflow. Additionally, even if recharge of Colorado River water occurs in the Central Wellfield, groundwater will become gradually salinized. The Act's restrictions on the use of CAP water affect the four regulatory mechanisms in Arizona's 1980 Groundwater Code as they relate to the Tucson Active Management Area: (a) supply augmentation; (b) requirements for groundwater withdrawals and permitting; (c) Management Plan requirements, particularly mandatory conservation and water-quality issues; and (d) the requirement that all new subdivisions use renewable water supplies in lieu of groundwater. Political fallout includes disruption of normal governmental activities because of the demands in implementing the Act. Résumé La loi de 1995 sur la protection des consommateurs d'eau de Tucson (Arizona, États-Unis) a été promulguée à la suite des réclamations des consommateurs d'eau de Tucson alimentés en eau traitée à partir à la station centrale d'Arizona (CAP). Les conséquences de cette loi montrent les incertitudes et les difficultés qui apparaissent lorsque le public est appeléà voter sur un problème très technique. Les exigences de la loi en matière de recharge négligent les incertitudes hydrogéologiques du fait de la confusion entre "infiltration" et "recharge". C'est ainsi que la loi laisse entendre que l'infiltration à partir des lits de rivières le long du champ captant central favorise la recharge de cette zone. En réalité, les différences de perméabilité entre les alluvions du lit et les dépôts sous-jacents remplissant le bassin peuvent provoquer un écoulement sous-jacent. En outre, même si une recharge par l'eau de la rivière Colorado se produit dans cette zone, la nappe sera progressivement salifiée. Les restrictions imposées par la loi quant à l'utilisation de l'eau de la station centrale d'Arizona affectent les quatre outils réglementaires du Code des eaux souterraines de l'Arizona de 1980, en ce qu'ils concernent la zone de gestion active de Tucson: (a) l'augmentation de l'approvisionnement (b) les conditions requises pour les prélèvements d'eau souterraine et les autorisations; (c) les conditions requises pour le plan de gestion, en particulier la pérennité du concessionnaire et les résultats en matière de qualité de l'eau et (d) la condition que tous les nouveaux districts aient recours à des ressources en eau renouvelables à la place de l'eau souterraine. Les demandes concernant la mise en oeuvre de la loi ont conduit jusqu'à l'arrêt des activités normales des instances politiques. Resumen El Acta de Protección de los Usuarios de Agua de Tucson, Arizona (EE.UU.) de 1995 (el Acta) se aprobó a raíz de las quejas de los usuarios de agua de Tucson que recibían agua tratada por el Proyecto de Arizona Central (CAP). Las consecuencias del Acta demuestran las incertidumbres y dificultades que se producen cuando se le pide al público que vote sobre temas muy técnicos. Los requerimientos de recarga del Acta desprecian incertidumbres hidrogeológicas al confundir entre "infiltración" y "recarga". Así, el Acta dice que la infiltración en los canales de los arroyos a lo largo del Campo de Producción Central aumentará la recarga a dicho campo. De hecho, la diferencia de permeabilidad entre el canal aluvial y los depósitos de relleno subyacentes puede provocar descarga subyacente. Además, incluso si el Río Colorado recargase este Campo Central, el agua subterránea se salinizaría progresivamente. Las restricciones del Acta sobre el uso del agua del CAP afectan los cuatro mecanismos legales del Código de Aguas Subterráneas de Arizona de 1980 relacionados con el Área de Gestión Activa de Tucson: (a) aumento del suministro; (b) requisitos y permisos para la extracción de aguas subterráneas (c) necesidades del Plan de Gestión, particularmente la conservación obligatoria y temas de calidad de aguas; y (d) la obligación de que todas las nuevas subdivisiones usen agua con suministro renovable en lugar de subterránea. Como problemas adicionales se incluye la perturbación de las actividades políticas normales como consecuencia de las demandas para aprobar y poner en marcha el Acta.
Thermodynamics of crystallization stresses in DEF
DOE Office of Scientific and Technical Information (OSTI.GOV)
Flatt, Robert J.; Scherer, George W.
2008-03-15
The thermo-mechanics of damage during delayed ettringite formation have been examined. A thermodynamic approach is used to evaluate the supersaturation under which ettringite may form and the crystallization pressures that may result. From these stresses at the pore scale and with the amount of ettringite forming, an average hydrostatic tensile stress in the solid is calculated and compared to the tensile strength of tested samples. Results indicate that, when the loading rate dependence of tensile strength is taken into account, it is possible to rationalize factors that do or do not contribute to damage, such as ettringite content, temperature andmore » fly-ash content. Although a number of important assumptions are made and clearly indicated in the paper, the results do open a new perspective onto durability studies which goes beyond the sole case of delayed ettringite formation.« less
Material handling systems for the fluidized-bed combustion boiler at Rivesville, West Virginia
NASA Technical Reports Server (NTRS)
Branam, J. G.; Rosborough, W. W.
1977-01-01
The 300,000 lbs/hr steam capacity multicell fluidized-bed boiler (MFB) utilizes complex material handling systems. The material handling systems can be divided into the following areas: (1) coal preparation; transfer and delivery, (2) limestone handling system, (3) fly-ash removal and (4) bed material handling system. Each of the above systems are described in detail and some of the potential problem areas are discussed. A major potential problem that exists is the coal drying system. The coal dryer is designed to use 600 F preheated combustion air as drying medium and the dryer effluent is designed to enter a hot electrostatic precipitator (730 F) after passage through a cyclone. Other problem areas to be discussed include the steam generator coal and limestone feed system which may have operating difficulties with wet coal and/or coal fines.
Process for removing sulfur from sulfur-containing gases: high calcium fly-ash
Rochelle, Gary T.; Chang, John C. S.
1991-01-01
The present disclosure relates to improved processes for treating hot sulfur-containing flue gas to remove sulfur therefrom. Processes in accordance with the present invention include preparing an aqueous slurry composed of a calcium alkali source and a source of reactive silica and/or alumina, heating the slurry to above-ambient temperatures for a period of time in order to facilitate the formation of sulfur-absorbing calcium silicates or aluminates, and treating the gas with the heat-treated slurry components. Examples disclosed herein demonstrate the utility of these processes in achieving improved sulfur-absorbing capabilities. Additionally, disclosure is provided which illustrates preferred configurations for employing the present processes both as a dry sorbent injection and for use in conjunction with a spray dryer and/or bagfilter. Retrofit application to existing systems is also addressed.
Flue gas conditioning for improved particle collection in electrostatic precipitators
DOE Office of Scientific and Technical Information (OSTI.GOV)
Durham, M.D.
1992-04-27
The purpose of this research program is to identify and evaluate a variety of additives capable of increasing particle cohesion which could be used for improving collection efficiency in an ESP. A three-phase screening process will be used to provide the, evaluation of many additives in a logical and cost-effective manner. The three step approach involves the following experimental setups: 1. Provide a preliminary screening in the laboratory by measuring the effects of various conditioning agents on reentrainment of flyash particles in an electric field operating at simulated flue gas conditions. 2. Evaluate the successful additives using a 100 acfmmore » bench-scale ESP operating on actual flue gas. 3. Obtain the data required for scaling up the technology by testing the two or three most promising conditioning agents at the pilot scale.« less
NASA Astrophysics Data System (ADS)
Rahli, O.; Tadrist, L.; Miscevic, M.; Santini, R.
1995-11-01
Experimental studies have been carried out on fluid flow through porous media made up of randomly packed monodisperse fibers. The fibers of fixed diameter have an aspect ratio (L/d) varying between 4 and 70 given porosities of the porous media varying between 0.35 and 0.90. The relationships between friction losses and superficial velocity have been systematically determined for each porous medium. A detailed analysis is carried out for low fluid velocities. The influence of flow direction on pressure drop is studied along two perpendicular directions: it is found that fibrous media behave globally in isotropic manner. The permeability and the Kozeny Carman parameter k_k are deduced from experimental results. The variations of the permeability increase exponentially with the porosity. The Kozeny Carman parameter k_k is a decreasing function of the porosity ɛ(L/d) and tends asymptotically to a value close to that deduced from a modified Ergun relation. The important decrease, observed for small aspect ratios, is certainly an effect of the cut sections of fibers. This effect becomes negligible for larger aspect ratios. The results in terms of permeability and of Kozeny Carman parameter k_k are systematically compared to those deduced from various theoretical models. Generally, these models consider cylinders arranged in simple network, the flow being either parallel or perpendicular to the axis of cylinders. The variation laws of the parameter k_k, deduced from different models, present important discrepancies with our experimental results. The theoretical models, established for regular arrays of fibers do not correctly describe the behavior of randomly packed fibers. Des études expérimentales de l'écoulement d'un fluide à travers un milieu poreux constitué de fibres monodisperses empilées aléatoirement sont réalisées. Les milieux fibreux étudiés ont des porosités variant de 0,35 à 0,90. Ces porosités sont obtenues à l'aide de fibres dont le rapport d'aspect L/d varie de 4 à 70. Les lois de perte de charge en fonction de la vitesse du fluide sont déterminées systématiquement pour chaque milieu poreux. Une analyse détaillée est effectuée pour les faibles vitesses d'écoulement. L'influence de la direction de l'écoulement sur les lois de perte de charge est étudiée. Celles-ci sont établies suivant deux directions perpendiculaires. Les résultats obtenus mettent en évidence un comportement du milieu fibreux globalement isotrope vis à vis de l'écoulement du fluide. La perméabilité et le paramètre de Kozeny Carman k_k sont déduits des résultats expérimentaux. Les variations de la perméabilité en fonction de la porosité suivent une loi de type exponentiel. Le paramètre de Kozeny Carman k_k décroît en fonction de la porosité ɛ(L/d) et tend asymptotiquement vers une valeur proche de celle déduite de la relation d'Ergun modifiée. La décroissance importante, observée pour les petits rapports d'aspect, est sans doute due aux effets induits par les surfaces de base des fibres. Ces effets deviennent négligeables pour les grands rapports d'aspect. Les résultats en terme de perméabilité et de paramètre de Kozeny Carman sont comparés systématiquement avec les modèles proposés dans la littérature. Généralement, ces modèles supposent des cylindres de grande longueur, disposés en réseaux simples. L'écoulement est soit parallèle, soit perpendiculaire à l'axe des cylindres. Les lois de variation du paramètre k_k, déduites des différents modèles, présentent des écarts importants avec les résultats expérimentaux. Ces résultats semblent montrer qu'une disposition des fibres en réseaux simples ne permet pas une description convenable des écoulements à travers les empilements aléatoires de fibres.
NASA Astrophysics Data System (ADS)
Morris, J.; Stoner, J. S.; Reilly, B. T.; Hatfield, R. G.; Konyndyk, D.; Abbott, M. B.; Finkenbinder, M. S.; Hillman, A. L.
2016-12-01
In order to better understand climate trends in the late Pleistocene and Holocene in southeast Oregon, we present a sedimentological analysis of Fish Lake, Harney County, Oregon. Fish Lake (42° 44' 15" N, 118° 38' 57" W, 2,246.7 m) sits on the west slope of Steens Mountain, a fault-block mountain of Miocene basalt, adjacent to a glacial moraine. The present environment is high desert with sub alpine steppe vegetation, receiving approximately 12" of precipitation annually. The lake was cored in August 2013 with a series of overlapping drives, correlated by six distinct tephra and magnetic susceptibility. The composite section provides a 7.5 m continuous record of at least the last 13 ka, constrained by an age model built with 13 terrestrial macrofossil 14C dates. The recovered sediments, consisting of fine terrigenous and biogenous material in varying proportions, were analyzed with computed tomography (CT) scans, x-ray fluorescence (XRF) scans, magnetic measurements, loss on ignition (LOI), and sediment grain-size. CT and LOI data reveal a low density, high organic interval in the early Holocene ( 8.5-11 ka) with relatively coarse and well-sorted grain-size, suggesting an extended period of low lake level and low precipitation. Sediment grain-sizes are variable through the middle and late Holocene with high amplitude longer period features from 3 ka to the present. We investigate these grain-size fluctuations in the context of regional Holocene records.
Wu, Qian; Zhang, Qian; Zhao, Li; Li, Shi-Neng; Wu, Lian-Bin; Jiang, Jian-Xiong; Tang, Long-Cheng
2017-08-15
In this study, a novel strategy was developed to fabricate highly flame retardant polymer foam composite materials coated by synthesized silicone resin (SiR) polymer via a facile dip-coating processing. Applying the SiR polymer coating, the mechanical property and thermal stability of SiR-coated polymer foam (PSiR) composites are greatly enhanced without significantly altering their structure and morphology. The minimum oxygen concentration to support the combustion of foam materials is greatly increased, i.e. from LOI 14.6% for pure foam to LOI 26-29% for the PSiR composites studied. Especially, adjusting pendant group to SiOSi group ratio (R/Si ratio) of SiRs produces highly flame retardant PSiR composites with low smoke toxicity. Cone calorimetry results demonstrate that 44-68% reduction in the peak heat release rate for the PSiR composites containing different R/Si ratios over pure foam is achieved by the presence of appropriate SiR coating. Digital and SEM images of post-burn chars indicate that the SiR polymer coating can be transformed into silica self-extinguishing porous layer as effective inorganic barrier effect, thus preserving the polymer foam structure from fire. Our results show that the SiR dip-coating technique is a promising strategy for producing flame retardant polymer foam composite materials with improved mechanical properties. Copyright © 2017 Elsevier B.V. All rights reserved.
Flammability of self-extinguishing kenaf/ABS nanoclays composite for aircraft secondary structure
NASA Astrophysics Data System (ADS)
Karunakaran, S.; Majid, D. L.; Mohd Tawil, M. L.
2016-10-01
This study investigates the flammability properties of kenaf fiber reinforced acrylonitrile butadiene styrene (ABS) with nanoclays composites. Natural fiber is one of the potential materials to be used with thermoplastic as a composite due to its attractive properties such as lightweight and strong. In this paper, flammability properties of this material are evaluated through Underwriters Laboratory 94 Horizontal Burning (UL94 HB), which has been conducted for both controlled and uncontrolled conditions, smoke density and limiting oxygen index tests (LOI). These flammability tests are in compliance with the Federal Aviation Regulation (FAR) requirement. The results from UL94 HB and smoke density tests show that the presence of nanoclays with effective composition of kenaf fiber reinforced ABS has enhanced the burning characteristics of the material by hindering propagation of flame spread over the surface of the material through char formation. Consequently, this decreases the burning rate and produces low amount of smoke during burning. On contrary, through LOI test, this material requires less oxygen to burn when exposed to fire, which hinders the enhancement of burning characteristics. This is due to burning mechanism exhibited by nanoclays that catalyzes barrier formation and flame propagation rate over the surface of the biocomposite material. Overall, these experimental results suggest that this biocomposite material is capable of self-extinguishing and possesses effective fire extinction. The observed novel synergism from the result obtained is promising to be implemented in secondary structures of aircraft with significant benefits such as cost-effective, lightweight and biodegradable self-extinguishing biocomposite.
Alcohol Marketing during the UEFA EURO 2016 Football Tournament: A Frequency Analysis
Critchlow, Nathan; Stead, Martine; Adams, Jean; Brown, Katherine
2017-01-01
This study examined the frequency and nature of alcohol marketing references in broadcasts of the 2016 UEFA (Union of European Football Associations) European Championships football tournament in the United Kingdom (UK). Eighteen matches from across the tournament were recorded in full as broadcast in the UK, including all four matches featuring the English national team and all seven featuring the French national team. All visual and verbal references to alcohol marketing were recorded using a tool with high inter-rater reliability. A total of 2213 alcohol marketing references were recorded, an average of 122.94 per broadcast and 0.65 per broadcast minute (0.52 per minute in-play and 0.80 per minute out-of-play). Almost all references were visual (97.5%), with 77.9% occurring around the pitch border. Almost all (90.6%) were indirect references to alcohol brands (e.g., references to well-known slogans), compared to only 9.4% direct references to brands (e.g., brand names). The frequency of references to alcohol marketing was high. Although the overall proportion of direct brand references was low, the high proportion of indirect references demonstrates that alcohol producers were able to circumvent the French national law governing alcohol marketing (the Loi Évin) using indirect “alibi marketing”. To ensure the spirit of the Loi Évin regulations are achieved, stricter enforcement may be required to limit exposure to alcohol marketing, particularly for young people. PMID:28661462
NASA Astrophysics Data System (ADS)
Song, Young-Joo; Bae, Jonghee; Kim, Young-Rok; Kim, Bang-Yeop
2017-12-01
To ensure the successful launch of the Korea pathfinder lunar orbiter (KPLO) mission, the Korea Aerospace Research Institute (KARI) is now performing extensive trajectory design and analysis studies. From the trajectory design perspective, it is crucial to prepare contingency trajectory options for the failure of the first lunar brake or the failure of the first lunar orbit insertion (LOI) maneuver. As part of the early phase trajectory design and analysis activities, the required time of flight (TOF) and associated delta-V magnitudes for each recovery maneuver (RM) to recover the KPLO mission trajectory are analyzed. There are two typical trajectory recovery options, direct recovery and low energy recovery. The current work is focused on the direct recovery option. Results indicate that a quicker execution of the first RM after the failure of the first LOI plays a significant role in saving the magnitudes of the RMs. Under the conditions of the extremely tight delta-V budget that is currently allocated for the KPLO mission, it is found that the recovery of the KPLO without altering the originally planned mission orbit (a 100 km circular orbit) cannot be achieved via direct recovery options. However, feasible recovery options are suggested within the boundaries of the currently planned delta-V budget. By changing the shape and orientation of the recovered final mission orbit, it is expected that the KPLO mission may partially pursue its scientific mission after successful recovery, though it will be limited.
Alcohol Marketing during the UEFA EURO 2016 Football Tournament: A Frequency Analysis.
Purves, Richard I; Critchlow, Nathan; Stead, Martine; Adams, Jean; Brown, Katherine
2017-06-29
This study examined the frequency and nature of alcohol marketing references in broadcasts of the 2016 UEFA (Union of European Football Associations) European Championships football tournament in the United Kingdom (UK). Eighteen matches from across the tournament were recorded in full as broadcast in the UK, including all four matches featuring the English national team and all seven featuring the French national team. All visual and verbal references to alcohol marketing were recorded using a tool with high inter-rater reliability. A total of 2213 alcohol marketing references were recorded, an average of 122.94 per broadcast and 0.65 per broadcast minute (0.52 per minute in-play and 0.80 per minute out-of-play). Almost all references were visual (97.5%), with 77.9% occurring around the pitch border. Almost all (90.6%) were indirect references to alcohol brands (e.g., references to well-known slogans), compared to only 9.4% direct references to brands (e.g., brand names). The frequency of references to alcohol marketing was high. Although the overall proportion of direct brand references was low, the high proportion of indirect references demonstrates that alcohol producers were able to circumvent the French national law governing alcohol marketing (the Loi Évin) using indirect "alibi marketing". To ensure the spirit of the Loi Évin regulations are achieved, stricter enforcement may be required to limit exposure to alcohol marketing, particularly for young people.
Castro-Fornieles, Josefina; Deulofeu, Ramón; Baeza, Immaculada; Casulà, Vanessa; Saura, Begoña; Lázaro, Luisa; Puig, Josefina; Toro, Josep; Bernardo, Miquel
2008-02-01
Dopaminergic abnormalities have been described in anorexia nervosa but studies about plasma level of homovanillic acid (pHVA) have yielded conflicting results probably due to the small number and the heterogeneity of patients. Plasma HVA, nutritional and hormonal parameters and several scales - the Eating Attitudes Test (EAT), the Beck Depression Inventory (BDI), the Leyton Obsessional Inventory-child version (LOI-C) and the State and Trait Anxiety Inventory (STAI) - were assessed in 44 adolescent anorexia nervosa patients (mean age 14.7 years, SD 1.7) consecutively admitted to an Eating Disorder Unit. They were evaluated at admission, at discharge and, in 34 cases, after 9 months of follow-up. pHVA was also assessed in 16 control adolescents. Patients had significantly higher pHVA than controls (p = .002). About 31% of patients had a very high level of pHVA, a significantly higher (p = .006) mean score in the BDI and a non significantly higher mean score in the EAT. After weight recovery some laboratory parameters improved as well as the EAT (p = .019), the BDI (p = 001) and the Interference score of the LOI-C (p = .004). Moreover, pHVA decreased significantly (p=.036). At follow-up, patients with normal weight had lower (p = .037) pHVA than patients with low weight. The conclusion would be that there is a dopaminergic dysfunction in anorexic patients, specially in a subgroup with high depressive and anorexic symptomatology. With weight recovery and psychopathological improvement, pHVA tends to normalization.
NASA Astrophysics Data System (ADS)
Xu, Bo; Ma, Wen; Wu, Xiao; Qian, Lijun; Jiang, Shan
2018-04-01
Intumescent flame retardant (IFR) EVA composites were prepared based on a hyperbranched triazine charring-foaming agent (HTCFA) and ammonium polyphosphate (APP). The synergistic effect of HTCFA and APP on the flame retardancy and thermal behavior of the composites were investigated through flammability tests, cone calorimeter measurements, thermogravimetric analysis (TGA) including evolved gas analysis (TG-IR) and residue analysis (Fourier transform infrared (FTIR), laser Raman spectroscopy (LRS), x-ray Photoelectron Spectroscopy (XPS) and scanning electron microscopy (SEM)). The flammability test results showed HTCFA/APP (1/3) system presented the best synergistic effect in flame-retardant EVA composites with the highest LOI value and UL-94 V-0 rating. As for cone calorimeter results, IFR changed the combustion behavior of EVA and resulted in remarkable decrease of flammability and smoke product. TGA results showed the synergistic effect between APP and HTCFA could strengthen the char-forming ability of composites. TG-IR results indicated the melt viscosities and gas release with increasing temperature were well-correlated for EVA/IFR composite. The residue analysis results from SEM, LRS, FT-IR and XPS revealed IFR promoted forming more compact graphitic char layer, connected by rich P–O–C and P–N structures.
Mercury in Fish, Bed Sediment, and Water from Streams Across the United States, 1998-2005
Scudder, Barbara C.; Chasar, Lia C.; Wentz, Dennis A.; Bauch, Nancy J.; Brigham, Mark E.; Moran, Patrick W.; Krabbenhoft, David P.
2009-01-01
Mercury (Hg) was examined in top-predator fish, bed sediment, and water from streams that spanned regional and national gradients of Hg source strength and other factors thought to influence methylmercury (MeHg) bioaccumulation. Sampled settings include stream basins that were agricultural, urbanized, undeveloped (forested, grassland, shrubland, and wetland land cover), and mined (for gold and Hg). Each site was sampled one time during seasonal low flow. Predator fish were targeted for collection, and composited samples of fish (primarily skin-off fillets) were analyzed for total Hg (THg), as most of the Hg found in fish tissue (95-99 percent) is MeHg. Samples of bed sediment and stream water were analyzed for THg, MeHg, and characteristics thought to affect Hg methylation, such as loss-on-ignition (LOI, a measure of organic matter content) and acid-volatile sulfide in bed sediment, and pH, dissolved organic carbon (DOC), and dissolved sulfate in water. Fish-Hg concentrations at 27 percent of sampled sites exceeded the U.S. Environmental Protection Agency human-health criterion of 0.3 micrograms per gram wet weight. Exceedances were geographically widespread, although the study design targeted specific sites and fish species and sizes, so results do not represent a true nationwide percentage of exceedances. The highest THg concentrations in fish were from blackwater coastal-plain streams draining forests or wetlands in the eastern and southeastern United States, as well as from streams draining gold- or Hg-mined basins in the western United States (1.80 and 1.95 micrograms THg per gram wet weight, respectively). For unmined basins, length-normalized Hg concentrations in largemouth bass were significantly higher in fish from predominantly undeveloped or mixed-land-use basins compared to urban basins. Hg concentrations in largemouth bass from unmined basins were correlated positively with basin percentages of evergreen forest and also woody wetland, especially with increasing proximity of these two land-cover types to the sampling site; this underscores the greater likelihood for Hg bioaccumulation to occur in these types of settings. Increasing concentrations of MeHg in unfiltered stream water, and of bed-sediment MeHg normalized by LOI, and decreasing pH and dissolved sulfate were also important in explaining increasing Hg concentrations in largemouth bass. MeHg concentrations in bed sediment correlated positively with THg, LOI, and acid-volatile sulfide. Concentrations of MeHg in water correlated positively with DOC, ultraviolet absorbance, and THg in water, the percentage of MeHg in bed sediment, and the percentage of wetland in the basin.
ERIC Educational Resources Information Center
Canadian Bar Association, Ottawa (Ontario).
A Canadian Bar Association Task Force on Legal Literacy explored the relationship between literacy and access to the legal system. A literature review revealed that little attention had been directed to literacy and use of the legal system. Three important findings emerged from 24 focus groups of current and former adult learners: virtually all…
User Manual for the AZ-101 Data Acquisition System (AS-101 DAS)
DOE Office of Scientific and Technical Information (OSTI.GOV)
BRAYTON, D.D.
2000-02-17
User manual for the TK AZ-101 Waste Retrieval System Data Acquisition System. The purpose of this document is to describe use of the AZ-101 Data Acquisition System (AZ-101 DAS). The AZ-101 DAS is provided to fulfill the requirements for data collection and monitoring as defined in Letters of Instruction (LOI) from Numatec Hanford Corporation (NHC) to Fluor Federal Services (FFS). For a complete description of the system, including design, please refer to the AZ-101 DAS System Description document, RPP-5572.
Testing and Measurement Techniques in Heat Transfer and Combustion.
1980-09-01
Is passage de lair de dilution au moyen d’une oeirie d’orlfices circu- laires , d’autre part leur propre refroidlseement grace A la cr~ation de films...dlenviron 20 % plus grand qua la valeur d~duite d’une meaure dana lair ambiant (en uti- lisant la loi en 273/T pour le nombre de mol~cules par unit6 de...question of possible bias of velocity measurement using a LDV when the seeding method is likely to produce nonuniformities of particle concentra- tion that
Exemples d’utilisation des techniques d’optimisation en calcul de structures de reacteurs
2003-03-01
34~ optimisation g~om~trique (architecture fig~e) A la difference du secteur automobile et des avionneurs, la plupart des composants des r~acteurs n...utilise des lois de comportement mat~riaux non lin~aires ainsi que des hypotheses de grands d~placements. Ltude d’optimisation consiste ý minimiser...un disque simple et d~cid6 de s~lectionner trois param~tes qui influent sur la rupture : 1paisseur de la toile du disque ElI, la hauteur L3 et la
TG-FTIR characterization of flame retardant polyurethane foams materials
NASA Astrophysics Data System (ADS)
Liu, W.; Tang, Y.; Li, F.; Ge, X. G.; Zhang, Z. J.
2016-07-01
Dimethyl methylphosphonate (DMMP) and trichloroethyl phosphtate (TCEP) have been used to enhance the flame retardancy of polyurethane foams materials (PUF). Flame retardancy and thermal degradation of PUF samples have been investigated by the LOI tests and thermal analysis. The results indicate that the excellent flame retardancy can be achieved due to the presence of the flame retardant system containing DMMP and TCEP. TG-FTIR reveals that the addition of DMMP/TCEP can not only improve the thermal stability of PUF samples but can also affect the gaseous phase at high temperature.
(210)Pb and compositional data of sediments from Rondonian lakes, Madeira River basin, Brazil.
Bonotto, Daniel Marcos; Vergotti, Marcelo
2015-05-01
Gold exploration has been intensive in Brazilian Amazon over the last 40 years, where the use of mercury as an amalgam has caused abnormal Hg concentrations in water bodies. Special attention has been directed to Madeira River due to fact it is a major tributary of Amazon River and that since 1986, gold exploration has been officially permitted along a 350km sector of the river. The (21)(0)Pb method has been used to date sediments taken from nine lakes situated in Madeira River basin, Rondônia State, and to verify where anthropogenic Hg might exist due to gold exploitation in Madeira River. Activity profiles of excess (21)(0)Pb determined in the sediment cores provided a means to evaluate the sedimentation rates using a Constant Flux: Constant Sedimentation (CF:CS) and Constant Rate of Supply (CRS) of unsupported/excess (21)(0)Pb models. A significant relationship was found between the CF:CS sedimentation rates and the mean values of the CRS sedimentation rates (Pearson correlation coefficient r=0.59). Chemical data were also determined in the sediments for identifying possible relationships with Hg occurring in the area. Significant values were found in statistical correlation tests realized among the Hg, major oxides and Total Organic Carbon (TOC) content in the sediments. The TOC increased in the sediment cores accompanied by a loss on ignition (LOI) increment, whereas silica decreased following a specific surface area raising associated to the TOC increase. The CRS model always provided ages within the permitted range of the (21)(0)Pb-method in the studied lakes, whereas the CF:CS model predicted two values above 140 years. Copyright © 2015 Elsevier Ltd. All rights reserved.
NASA Astrophysics Data System (ADS)
Wang, Qingyu; He, Lingfeng; Shi, Liang; Chen, Xiaogang; Chen, Xin; Xu, Zizhen; Zhang, Yongli
2018-03-01
Using high temperature activated sodium flying ash and carboxymethyl chitosan as raw material to prepare carboxymethylchitosan wrapping fly-ash adsorbent (CWF), combined with iron-carbon micro-electrolysis treatment of simulated and actual printing and dyeing wastewater. The conditions for obtaining are from the literature: the best condition for CWF to treat simulated printing and dyeing wastewater pretreated with iron-carbon micro-electrolysis is that the mixing time is 10min, the resting time is 30 min, pH=6, and the adsorbent dosage is 0.75 g/L. The results showed that COD removal efficiency and decoloration rate were above 97 %, and turbidity removal rate was over 90 %. The optimum dyeing conditions were used to treat the dyeing wastewater. The decolorization rate was 97.30 %, the removal efficiency of COD was 92.44 %, and the turbidity removal rate was 90.37 %.
Dissolution and Separation of Aluminum and Aluminosilicates
McFarlane, Joanna; Benker, Dennis; DePaoli, David W.; ...
2015-12-19
The selection of an aluminum alloy for target irradiation affects post-irradiation target dissolution and separations. Recent tests with aluminum alloy 6061 yielded greater than expected precipitation in the dissolver, forming up to 10 wt.% solids of aluminum hydroxides and aluminosilicates. Aluminosilicate dissolution presents challenges in a number of different areas, metals extraction from minerals, flyash treatment, and separations from aluminum alloys. We present experimental work that attempts to maximize dissolution of aluminum metal, along with silicon, magnesium, and copper impurities, through control of temperature, the rate of reagent addition, and incubation time. Aluminum phase transformations have been identified as amore » function of time and temperature, using X-ray diffraction. Solutions have been analyzed using wet chemical methods and X-ray fluorescence. Our data have been compared with published calculations of aluminum phase diagrams. Approaches are given to enhance the dissolution of aluminum and aluminosilicate phases in caustic solution.« less
Leaching properties of stabilised/solidified cement-admixtures-sewage sludges systems.
Valls, S; Vàzquez, E
2002-01-01
One of the main objectives of this work is to present an effective alternative for the final destination of sludge from urban waste water treatment plants by its use as a component of mortar or concrete. A binding and stabilizing matrix of sludge-cement and sludge-cement-coal fly-ash was investigated and the effects of various percentages of waste and binder, on the behavior of sludge in the system are presented. Assessment of the environmental quality of the final product and the consequent guarantee of its use in the building industry demand that it meets a number of requisites, one of which is that the effluents extracted by water action should be contamination-free, or at least that the concentration of contaminants should be below certain pre-set limits. For this a number of leaching tests must be carried out, such as the Netherlands Leaching Test .
Ambient Cured Alkali Activated Flyash Masonry Units
NASA Astrophysics Data System (ADS)
Venugopal, K.; Radhakrishna; Sasalatti, Vinod M.
2016-09-01
Geopolymers belong to a category of non-conventional and non-Portland cement based cementitious binders which are produced using industrial by products like fly ash and ground granulated blast furnace slag (GGBFS). This paper reports on the development of geopolymer mortars for production of masonry units. The geopolymer mortars were prepared by mixing various by products with manufactured sand and a liquid mixture of sodium silicate and sodium hydroxide solutions. After curing at ambient conditions, the masonry units were tested for strength properties such as water absorption, initial rate of absorption, compression, shear- bond, and stress-strain behaviour etc. It was observed that the flexural strength of the blocks is more than 2 MPa and shear bond strength is more than 0.4MPa. It was found that the properties of geopolymer blocks were superior to the traditional masonry units. Hence they can be recommended for structural masonry.
Study of Experiment on Rock-like Material Consist of fly-ash, Cement and Mortar
NASA Astrophysics Data System (ADS)
Nan, Qin; Hongwei, Wang; Yongyan, Wang
2018-03-01
Study the uniaxial compression test of rock-like material consist of coal ash, cement and mortar by changing the sand cement ratio, replace of fine coal, grain diameter, water-binder ratio and height-diameter ratio. We get the law of four factors above to rock-like material’s uniaxial compression characteristics and the quantitative relation. The effect law can be sum up as below: sample’s uniaxial compressive strength and elasticity modulus tend to decrease with the increase of sand cement ratio, replace of fine coal and water-binder ratio, and it satisfies with power function relation. With high ratio increases gradually, the uniaxial compressive strength and elastic modulus is lower, and presents the inverse function curve; Specimen tensile strength decreases gradually with the increase of fly ash. By contrast, uniaxial compression failure phenomenon is consistent with the real rock common failure pattern.
Cost analysis and outcomes of simple elbow dislocations
Panteli, Michalis; Pountos, Ippokratis; Kanakaris, Nikolaos K; Tosounidis, Theodoros H; Giannoudis, Peter V
2015-01-01
AIM: To evaluate the management, clinical outcome and cost implications of three different treatment regimes for simple elbow dislocations. METHODS: Following institutional board approval, we performed a retrospective review of all consecutive patients treated for simple elbow dislocations in a Level I trauma centre between January 2008 and December 2010. Based on the length of elbow immobilisation (LOI), patients were divided in three groups (Group I, < 2 wk; Group II, 2-3 wk; and Group III, > 3 wk). Outcome was considered satisfactory when a patient could achieve a pain-free range of motion ≥ 100° (from 30° to 130°). The associated direct medical costs for the treatment of each patient were then calculated and analysed. RESULTS: We identified 80 patients who met the inclusion criteria. Due to loss to follow up, 13 patients were excluded from further analysis, leaving 67 patients for the final analysis. The mean LOI was 14 d (median 15 d; range 3-43 d) with a mean duration of hospital engagement of 67 d (median 57 d; range 10-351 d). Group III (prolonged immobilisation) had a statistically significant worse outcome in comparison to Group I and II (P = 0.04 and P = 0.01 respectively); however, there was no significant difference in the outcome between groups I and II (P = 0.30). No statistically significant difference in the direct medical costs between the groups was identified. CONCLUSION: The length of elbow immobilization doesn’t influence the medical cost; however immobilisation longer than three weeks is associated with persistent stiffness and a less satisfactory clinical outcome. PMID:26301180
Tectonic affinities of the accreted basalts in southern Taiwan
NASA Astrophysics Data System (ADS)
Chen, Hsin-Yu; Yang, Huai-Jen; Liu, Yung-Hsin; Huang, Kuo-Fang; Takazawa, Eiichi
2018-06-01
Tectonic affinities of accreted basalts provide constraints on mass transport in convergent boundaries, improving our understandings on the evolution of regional geology. In this study, nineteen accreted basalts from the southernmost tip of Taiwan Island, which is on the convergent boundary between the Eurasian and Philippine Sea Plates, were analyzed for element concentrations as well as Sr, Nd, Hf, and Pb isotope ratios to investigate their tectonic affinities. All the samples contain > 3% LOI, reflecting post-magmatic alteration. LOI and Nb variation diagrams together with comparisons to oceanic basalt compositions indicated that the concentrations of most major elements and Rb, Sr, and Ba were modified by post-magmatic processes to varying extents, while P2O5, REE and HFSE remained immobile. Although some samples show Pb loss, most samples have Pb concentrations not affected by post-magmatic processes. Isotope ratios of Pb, Nd and Hf, generally reflect the mantle source characteristics. The εNd-εHf relationship and trace element abundance ratios indicated that the LREE-depleted samples were mostly scraped off the subducting South China Sea floor, reflecting the volumetric dominance of N-MORB on ocean floors. The overriding Philippine Sea Plate contributed both N-MORB and E-MORB to the accretionary prism. The tectonic affinities of the LREE-enriched samples, however, could not be unambiguously determined for the large geochemical variability of OIB from both subducting and overlying slabs. Based on our results, it is proposed that the tectonic affinity of the basalts in an accretionary prism can indicate the subduction polarity of the associated convergent boundary, providing a constraint for regional geology evolution.
Zhao, Xin; Liu, Xiaoliang; Wang, Guanjun; Wen, Xue; Zhang, Xiaoying; Hoffman, Andrew R; Li, Wei; Hu, Ji-Fan; Cui, Jiuwei
2016-08-09
Insulin-like growth factor II (IGF2) is maternally imprinted in most tissues, but the epigenetic regulation of the gene in cancer stem cells (CSCs) has not been defined. To study the epigenetic mechanisms underlying self-renewal, we isolated CSCs and non-CSCs from colon cancer (HT29, HRT18, HCT116), hepatoma (Hep3B), breast cancer (MCF7) and prostate cancer (ASPC) cell lines. In HT29 and HRT18 cells that show loss of IGF2 imprinting (LOI), IGF2 was biallelically expressed in the isolated CSCs. Surprisingly, we also found loss of IGF2 imprinting in CSCs derived from cell lines HCT116 and ASPC that overall demonstrate maintenance of IGF2 imprinting. Using chromatin conformation capture (3C), we found that intrachromosomal looping between the IGF2 promoters and the imprinting control region (ICR) was abrogated in CSCs, in parallel with loss of IGF2 imprinting in these CSCs. Loss of imprinting led to increased IGF2 expression in CSCs, which have a higher rate of colony formation and greater resistance to chemotherapy and radiotherapy in vitro. These studies demonstrate that IGF2 LOI is a common feature in CSCs, even when the stem cells are derived from a cell line in which the general population of cells maintain IGF2 imprinting. This finding suggests that aberrant IGF2 imprinting may be an intrinsic epigenetic control mechanism that enhances stemness, self-renewal and chemo/radiotherapy resistance in cancer stem cells.
Evaluation of Allelic Expression of Imprinted Genes in Adult Human Blood
Frost, Jennifer M.; Monk, Dave; Stojilkovic-Mikic, Taita; Woodfine, Kathryn; Chitty, Lyn S.; Murrell, Adele; Stanier, Philip; Moore, Gudrun E.
2010-01-01
Background Imprinted genes are expressed from only one allele in a parent-of-origin dependent manner. Loss of imprinted (LOI) expression can result in a variety of human disorders and is frequently reported in cancer. Biallelic expression of imprinted genes in adult blood has been suggested as a useful biomarker and is currently being investigated in colorectal cancer. In general, the expression profiles of imprinted genes are well characterised during human and mouse fetal development, but not in human adults. Methodology/Principal Findings We investigated quantitative expression of 36 imprinted genes in adult human peripheral blood leukocytes obtained from healthy individuals. Allelic expression was also investigated in B and T lymphocytes and myeloid cells. We found that 21 genes were essentially undetectable in adult blood. Only six genes were demonstrably monoallelic, and most importantly, we found that nine genes were either biallelic or showed variable expression in different individuals. Separated leukocyte populations showed the same expression patterns as whole blood. Differential methylation at each of the imprinting control loci analysed was maintained, including regions that contained biallelically expressed genes. This suggests in some cases methylation has become uncoupled from its role in regulating gene expression. Conclusions/Significance We conclude that only a limited set of imprinted genes, including IGF2 and SNRPN, may be useful for LOI cancer biomarker studies. In addition, blood is not a good tissue to use for the discovery of new imprinted genes. Finally, lymphocyte DNA methylation status in the adult may not always be a reliable indicator of monoallelic gene expression. PMID:21042416
Dwivedi, S; Tripathi, R D; Srivastava, S; Mishra, S; Shukla, M K; Tiwari, K K; Singh, R; Rai, U N
2007-02-01
The disposal of fly-ash (FA) from coal-fired power stations causes significant economic and environmental problems. Use of such contaminated sites for crop production and use of contaminated water for irrigation not only decreases crop productivity but also poses health hazards to humans due to accumulation of toxic metals in edible grains. In the present investigation, three rice cultivars viz., Saryu-52, Sabha-5204, and Pant-4 were grown in garden soil (GS, control) and various amendments (10%, 25%, 50%, 75% and 100%) of FA for a period of 90 days and effect on growth and productivity of plant was evaluated vis-a-vis metal accumulation in the plants. The toxicity of FA at higher concentration (50%) was reflected by the reduction in photosynthetic pigments, protein and growth parameters viz., plant height, root biomass, number of tillers, grain and straw weight. However, at lower concentrations (10-25%), FA enhanced growth of the plants as evident by the increase of studied growth parameters. The cysteine and non-protein thiol (NP-SH) content showed increase in their levels up to 100% FA as compared to control, however, maximum content was found at 25% FA in Saryu-52 and Pant-4 and at 50% FA in Sabha-5204. Accumulation of Fe, Si, Cu, Zn, Mn, Ni, Cd and As was investigated in roots, leaves and seeds of the plants. Fe accumulation was maximum in all the parts of plant followed by Si and both showed more translocation to leaves while Mn, Zn, Cu, Ni and Cd showed lower accumulation and most of the metal was confined to roots in all the three cultivars. As was accumulated only in leaves and was not found to be in detectable levels in roots and seeds. The metal accumulation order in three rice cultivars was Fe > Si > Mn > Zn > Ni > Cu > Cd > As in all the plant parts. The results showed that rice varieties Saryu-52 and Sabha-5204 were more tolerant and could show improved growth and yield in lower FA application doses as compared to Pant-4. Thus, Sabha-5204 and Saryu-52 are found suitable for cultivation in FA amended agricultural soils for better crop yields.
Coal Ash Aerosol in East Asian Outflow as a Source for Oceanic Deposition of Iron and Other Metals
NASA Astrophysics Data System (ADS)
Anderson, J. R.; Hua, X.
2008-12-01
While ocean deposition of East Asian dust is given significant emphasis as a source of biologically-active trace elements, iron in particular, dust events are episodic and highly seasonal. There is, however, a constant source of aerosol that is chemically similar to dust (albeit amorphous in structure rather than crystalline) in the ash particles emitted from many hundreds of coal-fired power plants that are sited along the entire coastal region of China and Korea. The emission controls on these facilities vary widely and, in even cases of state-of-the-art emission controls, the secondary release of ash can be significant. There are of course even more small industrial and household sources of coal combustion emissions, in most cases with little or no emissions controls. Ash from a modern coal-fired power facility in Korea has been examined chemically and morphologically with electron microscopic techniques. As is characteristic of all such facilities, two principal types of ash are present: (1) flyash, silicate glass spheres that are emitted with the smoke and removed by electrostatic precipitators; and (2) bottom ash, "clinkers" and noncombustible material sticking to the furnace walls that are mixed with water and ground after cooling, then removed as a slurry to a dumping area. In addition, iron sulfide (pyrite) is a common constituent of coal and provides both a source of sulfur dioxide gas and also molten iron spherical particles in the ash. The iron spheres then are rapidly oxidized upon cooling. Bottom ash is a more complex material than flyash in that it contains more iron and other trace metals, plus it contains varying amounts of uncombusted carbon. The post-combustion handling of bottom ash can lead to significant emissions despite the fact that little or none goes out the stack. The iron oxide spheres can also be emitted by this secondary method. The concentrations of ash can be very high in close proximity to power plants (PM10 of several hundred micrograms per cubic meter of air) and traces of these aerosols have been found in the ACE-Asia and PACDEX experiments above the Sea of Japan, the Yellow Sea and across the width of the North Pacific.
NASA Astrophysics Data System (ADS)
Callahan, R.; Hartshorn, T.
2014-12-01
Fire severity can be defined using satellite imagery to ratio mid (~2.2 um) to near (~0.8 um) infrared reflectance values. We examined how lithology and topography affected burn severity, and how post-fire soils data could be used to ground-truth burn severity at two sites in southwestern Montana. A burned area reflectance classification (BARC), lithology, and terrain attributes were used to predict burn severity for the Millie Fire, which was triggered two years ago by lightning and burned ~4,000 ha. Burn severity showed a strong dependence on lithology: the ratio of areas with high burn severity vs. low or moderate burn severities was 2.9 for gneiss (vs. 0.3 for volcanics). The high-severity burn area for the gneiss was larger than the volcanics, despite the latter lithology covering ~270% greater area (~2,600 ha). Aspect and elevation also influenced burn severity with lower severity at higher elevations (2,600-3,000 m) and higher severity at lower elevations (1,800-2,400 m). Southern and western aspects burned more severely than northern and eastern aspects. To clarify whether post-fire soil geochemical changes might predict ground-based estimates of fire severity, a lab experiment was carried out . We expected residual enrichment of trace metal concentrations, as soil organic matter (SOM) was combusted, which we quantified as loss on ignition (LOI). To test this approach, burned and unburned soils were sampled from the ~6000 ha Beartrap 2 fire, which also burned two years. We simulated differing fire severities on unburned soil using a muffle furnace factorially (duration [5, 15, 30, 45, or 60 minutes] x temperature [50, 100, 200, 300, 400, or 500ºC]). Consistent with expectations, unburned samples had a lower mean (±1SD) concentrations for 23 of 30 elements than field-burned samples. For example, barium concentrations ([Ba]) in unburned samples were (708±37μg/g), 16% lower than field-burned [Ba] (841±7 μg/g). Simulated burning yielded smaller [Ba] (732±9 μg/g). Of the 30 trace metals examined, barium explained the greatest fraction of variance in post-burn LOI (R2 =0.79); gallium explained slightly less variance (R2=0.67). Our results document the promise of post-burn soil geochemistry to indicate soil burn severity, which could complement vegetation-based and remotely sensed indices.
NASA Astrophysics Data System (ADS)
Farkaš, Juraj; Chrastný, Vladislav; Novák, Martin; Čadkova, Eva; Pašava, Jan; Chakrabarti, Ramananda; Jacobsen, Stein B.; Ackerman, Lukáš; Bullen, Thomas D.
2013-12-01
Here we report chromium isotope compositions, expressed as δ53/52Cr in per mil (‰) relative to NIST 979, measured in selected Cr-rich minerals and rocks formed by the primary magmatic as well as the secondary metamorphic and weathering processes. The main objectives of this study were: (i) to further constrain the isotope composition of the Earth’s mantle Cr inventory and its possible variation during geological history, based on the analysis of globally distributed and stratigraphically constrained mantle-derived chromites; and (ii) to investigate the magnitude and systematics of Cr isotope fractionation during oxidative weathering and secondary alteration (i.e., hydration, serpentinization) of the magmatic Cr sources. Specifically, we analyzed δ53/52Cr in a set of globally distributed mantle-derived chromites (FeMgCr2O4, n = 30) collected from various locations in Europe, Asia, Africa and South America, and our results confirm that a chromite-hosted Earth’s mantle Cr inventory is uniform at -0.079 ± 0.129‰ (2SD), which we named here as a ‘canonical’ mantle δ53/52Cr signature. Furthermore our dataset of stratigraphically constrained chromites, whose crystallization ages cover most of the Earth’s geological history, indicate that the bulk Cr isotope composition of the chromite-hosted mantle inventory has remained uniform, within about ±0.100‰, since at least the Early Archean times (∼3500 million years ago, Ma). To investigate the systematics of Cr isotope fractionation associated with alteration processes we analyzed a number of secondary Cr-rich minerals and variably altered ultramafic rocks (i.e., serpentinized harzburgites, lherzolites) that revealed large positive δ53/52Cr anomalies that are systematically shifted to higher values with an increasing degree of alteration and serpentinization. The degree of aqueous alteration and serpentinization was quantified by the abundances of fluid-mobile (Rb, K) elements, and by the Loss On Ignition (LOI) parameter, which determines the amount of structurally bound water (OH/H2O) present in secondary hydrated minerals like serpentine. Overall, we observed that altered ultramafic rocks that yielded the highest LOI values, and the lowest amounts of fluid mobile elements, also yielded the heaviest δ53/52Cr signatures. Therefore, we conclude that secondary alteration (i.e., hydration, serpentinization) of ultramafic rocks in near-surface oxidative environments tend to shift the bulk Cr isotope composition of the weathered products to isotopically heavier values, pointing to a dynamic redox cycling of Cr in the Earth’s crustal and near-surface environments. Hence, if validated by future studies, this would suggest that Cr isotopes could be used to trace the recycling of altered oceanic lithosphere through subduction zones, and to detect the sources of dehydrated and previously serpentinized oceanic crust carrying ‘heavy’ δ53/52Cr signatures in island arc systems. Finally, the fact that the geogenic Cr sources may locally exhibit anomalous (non-canonical) δ53/52Cr signatures has also implications for environmental studies that use δ53/52Cr as a tracer to quantify the amount of the hexavalent Cr reduction in waters.
Evaluation of Visibility Sensors at the Eglin Air Force Base Climatic Chamber.
1983-10-01
s o t LI a of to -NAIC 6/81- -11 * VIow:1710 tons e- I: l - llO 26 5 6 Os *15 eeas IIg " 25 l5 .0 36 15 lOI (C) RYC (d) FIGURE 5-15. HOMOGENEITY OF...4 inch thick white plastic scattering disk. Since the exact attenuation of a filter can vary by as much as a factor of two, there was no way to...translucent plastic disk as scatterer and was found to be unchanged. The difference in calibration between Event 1 (slope - 0.88) and Event 2 (slope
1987-03-01
DISTORTION UNSTEADY INLET DISTORTION CHARACTERISTICS WITH THE B-1 B by C.J.MacMiler and W.R.Haagenson 16 DETERMINATION EXPERIMENTALE DES LOIS DE TRANSFERT DE...compresseurs. Dens ce domaine. los trois principaux objectifs du motoriste sont los suivants (a) - d6mont rer avant los essais en vol. la compatibilitA...ann~es sur la conception des moteurs deavions. 2 - ETHODES DE CALCUL 2.1. METNODES DES SECTEURS DE COMPRESSEUR EN PARALLELE 2.1.1. Description do la m
2011-10-01
partners of the CRTI and PSTP programs in applying and receiving positive status under the SAFTEY Act is a valuable service that DRDC-CSS can supply...Canadian industry partners of the CRTI/PSTP program into successfully applying for designation under the USA SAFETY Act, and preferably to be added...to the Department of Homeland Security Approved Product List (APL). This will enable Canadian companies to access these markets with the outputs of
Electrochemical Studies of Atmospheric Corrosion.
1979-01-01
d -. vi ~~ ‘ ~~~~~~~~~~~~~~~~~~~ Director , Metallurgy Programs Material Sciences Div is ion Office of Naval Research 7~ - ~~800 North Quincy...STATEMENT (of At . R.porE) Approved for Public Re l ease; distribution unlimited ‘7. OISTRISUTION STATEMENT (of A. .b.’t.c( ent.,. d lie Block 20. II...t Unclassified 20 ~~~~~~~~ C~ AUIPICAYION OP Tifil PAO*(IThoi D . S~loi.d) ‘from polarization resistance measurements using the CORFIT computer
Modelisation de la diffusion sur les surfaces metalliques: De l'adatome aux processus de croissance
NASA Astrophysics Data System (ADS)
Boisvert, Ghyslain
Cette these est consacree a l'etude des processus de diffusion en surface dans le but ultime de comprendre, et de modeliser, la croissance d'une couche mince. L'importance de bien mai triser la croissance est primordiale compte tenu de son role dans la miniaturisation des circuits electroniques. Nous etudions ici les surface des metaux nobles et de ceux de la fin de la serie de transition. Dans un premier temps, nous nous interessons a la diffusion d'un simple adatome sur une surface metallique. Nous avons, entre autres, mis en evidence l'apparition d'une correlation entre evenements successifs lorsque la temperature est comparable a la barriere de diffusion, i.e., la diffusion ne peut pas etre associee a une marche aleatoire. Nous proposons un modele phenomenologique simple qui reproduit bien les resultats des simulations. Ces calculs nous ont aussi permis de montrer que la diffusion obeit a la loi de Meyer-Neldel. Cette loi stipule que, pour un processus active, le prefacteur augmente exponentiellement avec la barriere. En plus, ce travail permet de clarifier l'origine physique de cette loi. En comparant les resultats dynamiques aux resultats statiques, on se rend compte que la barriere extraite des calculs dynamiques est essentiellement la meme que celle obtenue par une approche statique, beaucoup plus simple. On peut donc obtenir cette barriere a l'aide de methodes plus precises, i.e., ab initio, comme la theorie de la fonctionnelle de la densite, qui sont aussi malheureusement beaucoup plus lourdes. C'est ce que nous avons fait pour plusieurs systemes metalliques. Nos resultats avec cette derniere approche se comparent tres bien aux resultats experimentaux. Nous nous sommes attardes plus longuement a la surface (111) du platine. Cette surface regorge de particularites interessantes, comme la forme d'equilibre non-hexagonale des i lots et deux sites d'adsorption differents pour l'adatome. De plus, des calculs ab initio precedents n'ont pas reussi a confirmer la forme d'equilibre et surestiment grandement la barriere. Nos calculs, plus complets et dans un formalisme mieux adapte a ce genre de probleme, predisent correctement la forme d'equilibre, qui est en fait due a un relachement different du stress de surface aux deux types de marches qui forment les cotes des i lots. Notre valeur pour la barriere est aussi fortement diminuee lorsqu'on relaxe les forces sur les atomes de la surface, amenant le resultat theorique beaucoup plus pres de la valeur experimentale. Nos calculs pour le cuivre demontre en effet que la diffusion de petits i lots pendant la croissance ne peut pas etre negligee dans ce cas, mettant en doute la valeur des interpretations des mesures experimentales. (Abstract shortened by UMI.)
NASA Astrophysics Data System (ADS)
Thompson Davis, P.; Machalett, Björn; Gosse, John
2013-04-01
Varved lake sediments, which provide ideal high-resolution climate proxies, are not commonly available in many geographic areas over long time scales. This paper utilizes high-resolution grain-size analyses (n = 1040) from a 520-cm long sediment core from Lower Titcomb Lake (LTL), which lies just outside the type Titcomb Basin (TTB) moraines in the Wind River Range, Wyoming. The TTB moraines lie between Lower Titcomb Lake and Upper Titcomb Lake (UTL), about 3 km beyond, and 200 m lower than the modern glacier margin and Gannett Peak (Little Ice Age) moraines in the basin. Based on cosmogenic exposure dating, the TTB moraines are believed to be Younger Dryas (YD) age (Gosse et al., 1995) and lie in a geomorphic position similar to several other outer cirque moraines throughout the western American Cordillera. Until recently, many of these outer cirque moraines were believed to be Neoglacial age. The sediment core discussed here is one of five obtained from the two Titcomb Lakes, but is by the far the longest with the oldest sediment depositional record. Two AMS radiocarbon ages from the 445- and 455-cm core depths (about 2% loss on ignition, LOI) suggest that the lake basin may have been ice-free as early as 16.1 or even 16.8 cal 14C kyr, consistent with 10Be and 26Al exposure ages from boulders and bedrock surfaces outside the TTB moraines. The 257-cm depth in the core marks an abrupt transition from inorganic, sticky gray silt below (<1% LOI) to more organic, less sticky, light brown silt above (4-10% LOI). Eight AMS radiocarbon ages on bulk sediment and macrofossils date the transition to about 11.6 cal 14C kyr. Thus, sampling resolution above the transition is about 22.57 yr and below the transition is about 12.56 yr, consistent with a decreased sediment accumulation rate in LTL when Younger Dryas ice pulled back from the TTB moraines opening up UTL as a sediment depositional basin. The presented high-resolution grain size record reveals amplitudes and other structural features similar to delta 18O records from deep-lake ostracods in southern Germany, the Greenland ice core record, and speleothems in China. Major increases in the 2 - 8 µm grain size fraction indicative of increased glacier rock flour production between the 257 and 466 cm core depths appear to be roughly correlative with the YD-Alleröd-Bölling-Meiendorf-Heinrich 1 climate events recognized in other terrestrial records and Northern Atlantic Ocean marine cores, but provide much higher resolution than most of those records from a climate-sensitive alpine region in North America.
Rwei, Syang-Peng; Chen, Yu-Ming; Chiang, Whe-Yi; Ting, Yi-Tien
2017-01-01
A UV-curable, flame-retardant monomer, DAPP (bis[di-acryloyloxyethyl]-p-tert-butyl-phenyl-phosphate), was synthesized based on BPDCP (4-tert-butylphenyl-dichloro phosphate) and HEA (2-hydroxy ethyl acrylate). DAPP was blended with regular bisphenol A epoxy acrylate (BAEA) in various ratios to yield various phosphorus contents. The TGA-IR (thermogravimetric analyzer interface with an infrared spectrometer) results demonstrate that compounding 30 mol % DAPP with BAEA significantly reduced the amount of released CO gas. In contrast, the peak intensity of CO2 is independent of phosphorus content. The limiting oxygen index (LOI), reaching the saturated value of 26, and the heat release rate (HRR) measured using a cone-calorimeter, 156.43 KW/m2, confirm the saturation point when 30 mol % DAPP was compounded into BAEA. A study of the kinetics of pyrolysis reveals that Ea decreases as the phosphorus content increases. Both the TGA-IR and pyrolysis results reveal that the phosphorus compound DAPP is easily decomposed during the initial stage of burning to form an insulating layer, which inhibits further burning of the resin and the consequent release of other flammable gases. PMID:28772562
The Scottish way - getting results in soil spectroscopy without spending money
NASA Astrophysics Data System (ADS)
Aitkenhead, Matt; Cameron, Clare; Gaskin, Graham; Choisy, Bastien; Coull, Malcolm; Black, Helaina
2016-04-01
Achieving soil characterisation using spectroscopy requires several things. These include soil data to develop or train a calibration model, a method of capturing spectra, the ability to actually develop a calibration model and also additional data to reinforce the model by introducing some form of stratification or site-specific information. Each of these steps requires investment in both time and money. Here we present an approach developed at the James Hutton Institute that achieves the end goal with minimal cost, by making as much use as possible of existing soil and environmental datasets for Scotland. The spectroscopy device that has been developed is PHYLIS (Prototype HYperspectral Low-cost Imaging System) that was constructed using inexpensive optical components, and uses a basic digital camera to produce visible-range spectra. The results show that for a large number of soil parameters, it is possible to estimate values either very well (RSQ > 0.9) (LOI, C, exchangeable H), well (RSQ > 0.75) (N, pH) or moderately (RSQ > 0.5) (Mg, Na, K, Fe, Al, sand, silt, clay). The methods used to achieve these results are described. A number of additional parameters were not well estimated (elemental concentrations), and we describe how work is ongoing to improve our ability to estimate these using similar technology and data.
NASA Astrophysics Data System (ADS)
Xue, Baoxia; Niu, Mei; Yang, Yongzhen; Bai, Jie; Song, Yinghao; Peng, Yun; Liu, Xuguang
2017-08-01
In this account, magnesium hydroxide (MH) employed as a capsule wall was firstly coated on the surface of carbon microspheres (CMSs) to obtain MH@CMSs using liquid phase deposition, then was modified by 3-Aminopropyltriethoxysilane (APTS) to form FMH@CMSs. To investigate the interface binding forces, a series of PET composites was prepared by melt compounding with MH@CMSs or FMH@CMSs. Field-emission scanning electron microscopy (FESEM), Transmission electron microscopy (TEM), Fourier-transform Infrared spectrometry (FTIR) and X-ray photoelectron spectroscopy (XPS) were used to characterize the morphology, chemical structure, and effect of functionalization of CMSs. The coating degree and thermal stability were investigated by thermogravimetry analysis. The results showed that CMSs were coated by an inorganic shell layer of MH as a capsule wall. On the other hand, MH@CMSs were coated with an organic layer of APTS. When compared to MH@CMSs, the interface binding forces between FMH@CMSs and PET matrix were significantly improved, and the tensile strength of FMH@CMSs/PET was higher than that of MH@CMSs/PET. At 1 wt% mass fraction of FMH@CMSs, the limiting oxygen index (LOI) value of PET composites increased from 21% to 27.6% following a V-0 rating. The tensile strength of FMH@CMSs/PET increased by 66.2% to reach 47.20 MPa, a value nearly similar to that of PET. Overall, the formed two layers provided the FMH@CMSs/PET with good mechanical and flame-retardant properties, which would broaden their scope of application.
NASA Astrophysics Data System (ADS)
Gamboa, Adriana; Montero-Serrano, Jean-Carlos; St-Onge, Guillaume; Rochon, André; Desiage, Pierre-Arnaud
2017-02-01
Mineralogical, geochemical, magnetic, and siliciclastic grain-size signatures of 34 surface sediment samples from the Mackenzie-Beaufort Sea Slope and Amundsen Gulf were studied in order to better constrain the redox status, detrital particle provenance, and sediment dynamics in the western Canadian Arctic. Redox-sensitive elements (Mn, Fe, V, Cr, Zn) indicate that modern sedimentary deposition within the Mackenzie-Beaufort Sea Slope and Amundsen Gulf took place under oxic bottom-water conditions, with more turbulent mixing conditions and thus a well-oxygenated water column prevailing within the Amundsen Gulf. The analytical data obtained, combined with multivariate statistical (notably, principal component and fuzzy c-means clustering analyses) and spatial analyses, allowed the division of the study area into four provinces with distinct sedimentary compositions: (1) the Mackenzie Trough-Canadian Beaufort Shelf with high phyllosilicate-Fe oxide-magnetite and Al-K-Ti-Fe-Cr-V-Zn-P contents; (2) Southwestern Banks Island, characterized by high dolomite-K-feldspar and Ca-Mg-LOI contents; (3) the Central Amundsen Gulf, a transitional zone typified by intermediate phyllosilicate-magnetite-K-feldspar-dolomite and Al-K-Ti-Fe-Mn-V-Zn-Sr-Ca-Mg-LOI contents; and (4) mud volcanoes on the Canadian Beaufort Shelf distinguished by poorly sorted coarse-silt with high quartz-plagioclase-authigenic carbonate and Si-Zr contents, as well as high magnetic susceptibility. Our results also confirm that the present-day sedimentary dynamics on the Canadian Beaufort Shelf is mainly controlled by sediment supply from the Mackenzie River. Overall, these insights provide a basis for future studies using mineralogical, geochemical, and magnetic signatures of Canadian Arctic sediments in order to reconstruct past variations in sediment inputs and transport pathways related to late Quaternary climate and oceanographic changes.
Murray, Rachael; Breton, Magdalena Opazo; Britton, John; Cranwell, Jo; Grant-Braham, Bruce
2018-04-25
Alcohol advertising is a key driver of alcohol consumption, and is prohibited in France by the Loi Evin. In 2016 the Danish brewer Carlsberg sponsored the UEFA Euro 2016 finals, held in France, and used the alibis 'Probably' and '…the best in the world' in place of Carlsberg in pitch-side advertising. We have quantified the advertising exposure achieved during the final seven games in the UEFA Euro 2016 championship. Appearances of the Carlsberg alibis 'Probably' and 'the best in the world' were counted and timed to the nearest second during all active play in live coverage of quarter final, semi-final and final matches broadcast in the UK. We used census data and viewing figures from Kantar Media to estimate gross and per capita impressions of these advertisements in the UK population. In 796 min, 29 s of active play there were 746 alibi appearances, totalling 68 min 35 s duration and representing 8.6% of active playing time. Appearances were particularly frequent at the end of normal time, extra time and penalties. The seven matches delivered up to 7.43 billion Carlsberg alibi impressions to UK adults and 163.3 million to children. In the only match involving a second country with laws prohibiting alcohol advertising (France versus Iceland), exposure occurred for only 1.8% of playing time. Alibi marketing achieved significant advertising coverage during the final seven EURO 2016 championship games, particularly to children. Since 'Probably' is registered by Carlsberg as a wordmark this advertising appears to contravene the Loi Evin, though Carlsberg have defended their marketing actions.
ADAS Update and Maintainability
NASA Technical Reports Server (NTRS)
Watson, Leela R.
2010-01-01
Since 2000, both the National Weather Service Melbourne (NWS MLB) and the Spaceflight Meteorology Group (SMG) have used a local data integration system (LOIS) as part of their forecast and warning operations. The original LOIS was developed by the Applied Meteorology Unit (AMU) in 1998 (Manobianco and Case 1998) and has undergone subsequent improvements. Each has benefited from three-dimensional (3-D) analyses that are delivered to forecasters every 15 minutes across the peninsula of Florida. The intent is to generate products that enhance short-range weather forecasts issued in support of NWS MLB and SMG operational requirements within East Central Florida. The current LDIS uses the Advanced Regional Prediction System (ARPS) Data Analysis System (AD AS) package as its core, which integrates a wide variety of national, regional, and local observational data sets. It assimilates all available real-time data within its domain and is run at a finer spatial and temporal resolution than current national or regional-scale analysis packages. As such, it provides local forecasters with a more comprehensive understanding of evolving fine-scale weather features. Over the years, the LDIS has become problematic to maintain since it depends on AMU-developed shell scripts that were written for an earlier version of the ADAS software. The goals of this task were to update the NWS MLB/SMG LDIS with the latest version of ADAS, incorporate new sources of observational data, and upgrade and modify the AMU-developed shell scripts written to govern the system. In addition, the previously developed ADAS graphical user interface (GUI) was updated. Operationally, these upgrades will result in more accurate depictions of the current local environment to help with short-range weather forecasting applications, while also offering an improved initialization for local versions of the Weather Research and Forecasting (WRF) model used by both groups.
Chromium isotope heterogeneity in the mantle
NASA Astrophysics Data System (ADS)
Xia, Jiuxing; Qin, Liping; Shen, Ji; Carlson, Richard W.; Ionov, Dmitri A.; Mock, Timothy D.
2017-04-01
To better constrain the Cr isotopic composition of the silicate Earth and to investigate potential Cr isotopic fractionation during high temperature geological processes, we analyzed the Cr isotopic composition of different types of mantle xenoliths from diverse geologic settings: fertile to refractory off-craton spinel and garnet peridotites, pyroxenite veins, metasomatised spinel lherzolites and associated basalts from central Mongolia, spinel lherzolites and harzburgites from North China, as well as cratonic spinel and garnet peridotites from Siberia and southern Africa. The δ53CrNIST 979 values of the peridotites range from - 0.51 ± 0.04 ‰ (2SD) to + 0.75 ± 0.05 ‰ (2SD). The results show a slight negative correlation between δ53Cr and Al2O3 and CaO contents for most mantle peridotites, which may imply Cr isotopic fractionation during partial melting of mantle peridotites. However, highly variable Cr isotopic compositions measured in Mongolian peridotites cannot be caused by partial melting alone. Instead, the wide range in Cr isotopic composition of these samples most likely reflects kinetic fractionation during melt percolation. Chemical diffusion during melt percolation resulted in light Cr isotopes preferably entering into the melt. Two spinel websterite veins from Mongolia have extremely light δ53Cr values of - 1.36 ± 0.04 ‰ and - 0.77 ± 0.06 ‰, respectively, which are the most negative Cr isotopic compositions yet reported for mantle-derived rocks. These two websterite veins may represent crystallization products from the isotopically light melt that may also metasomatize some peridotites in the area. The δ53Cr values of highly altered garnet peridotites from southern Africa vary from - 0.35 ± 0.04 ‰ (2SD) to + 0.12 ± 0.04 ‰ (2SD) and increase with increasing LOI (Loss on Ignition), reflecting a shift of δ53Cr to more positive values by secondary alteration. The Cr isotopic composition of the pristine, fertile upper mantle is estimated as δ53Cr = - 0.14 ± 0.12 ‰, after corrections for the effects of partial melting and metasomatism. This value is in line with that estimated for the BSE (- 0.12 ± 0.10 ‰) previously.
DOE Office of Scientific and Technical Information (OSTI.GOV)
NONE
2006-07-01
A variety of papers/posters were presented on topics concerning power generation, including solid oxide fuel cells, hydrogen production, mercury as a combustion product, carbon dioxide separation from flue gas. A total of 31 presentations in slide/overview/viewgraph form and with a separate abstract are available online (one in abstract form only) and 24 poster papers (text). In addition 41 abstracts only are available. Papers of particular interest include: Hydrogen production from hydrogen sulfide in IGCC power plants; Oxidation of mercury in products of coal combustion; Computer aided design of advanced turbine aerofoil alloys for industrial gas turbines in coal fired environments;more » Developing engineered fuel using flyash and biomass; Conversion of hydrogen sulfide in coal gases to elemental sulfur with monolithic catalysts; Intelligent control via wireless sensor networks for advanced coal combustion systems; and Investment of fly ash and activated carbon obtained from pulverized coal boilers (poster).« less
Engineering evaluation of the use of the Timberline condensing economizer for particulate collection
DOE Office of Scientific and Technical Information (OSTI.GOV)
Butcher, T.; Serry, H.
1980-12-01
The possible use of the Timberline Industries condensing economizer as a particulate collection device on commercial sector boilers which are being converted to coal-oil mixture (COM) firing has been considered. The saturation temperature of the water vapor in the flue gas has been estimated as a function of excess air and ambient relative humidity. Also, boiler stack losses have been estimated for a variety of operating conditions including stack temperatures below the dew point. The condensing economizer concept will be limited to applications which can use the low temperature heat including water heating and forced air space heating. The potentialmore » particulate collection efficiency, water disposal, and similar heat recovery devices are discussed. A cost analysis is presented which indicates that the economizer system is not competitive with a cyclone but is competitive with a baghouse. The use of the cyclone is limited by collection efficiency. The measurement of COM flyash particle size distribution is recommended.« less
Radiation exposures due to fossil fuel combustion
NASA Astrophysics Data System (ADS)
Beck, Harold L.
The current consensus regarding the potential radiation exposures resulting from the combustion of fossil fuels is examined. Sources, releases and potential doses to humans are discussed, both for power plants and waste materials. It is concluded that the radiation exposure to most individuals from any pathway is probably insignificant, i.e. only a tiny fraction of the dose received from natural sources in soil and building materials. Any small dose that may result from power-plant emissions will most likely be from inhalation of the small insoluble ash particles from the more poorly controlled plants burning higher than average activity fuel, rather than from direct or indirect ingestion of food grown on contaminated soil. One potentially significant pathway for exposure to humans that requires further evaluation is the effect on indoor external γ-radiation levels resulting from the use of flyash in building materials. The combustion of natural gas in private dwellings is also discussed, and the radiological consequences are concluded to be generally insignificant, except under certain extraordinary circumstances.
2012-12-01
la Reine (en droit du Canada), telle que représentée par le ministre de la Défense nationale, 2012 DRDC CSS TM 2012-029 i...importantes forces d’application de la loi et de sécurité nationale de l’histoire du Canada. L’empreinte de la sécurité du théâtre d’opérations des Jeux...sécurité et de défense par la mise en place d’une « ville scientifique » mobile. La réussite du déploiement des
Effects of 1 HZ Imposed Bulk Flow Unsteadiness on Laminar/Turbulent Transition in a Straight Channel
1989-12-01
behavior near surfaces of operating turbines and airfoils . Non-equilibrium shear layer development near turbine passage surfaces and near airfoils is due to...F 2EIT E21’T t’TF 9011 Z60-180 (S/W) iH~ Figure 60. 93 (T)(T rcu In -iuri Lw mm~ ~m 0 Ln Li V Ln -4 a: LOi LL~ w -W;r ZO U 1> (S/W) .LUHn Figure 61 ...Thinsition R. Eppler and H. Fasell, eds. Springer-Verlag. pp. 37-46. 1985. 7. Nishioka, M., Assi, M., ’Three Dimensional Wave Disturbances in Plane
Pressing back: Split Britches' Lost Lounge and the retro performativity of lesbian performance.
Eschen, Nicole
2013-01-01
Using theories of affect and queer temporality, this article examines Split Britches' Lost Lounge as lesbian resistance to the pressures to remember or forget the past, condemn or embrace the future. In this piece, butch-femme duo Peggy Shaw and Lois Weaver develop a retro performativity that pushes back against systems that strive to make lesbianism invisible, private, and apolitical. Through performances that resignify past pop culture artifacts, particularly the duo of Louis Prima and Keely Smith, Shaw and Weaver perform a past that is simultaneously lost and embodied, pressuring the audience to reconsider notions of progress and beauty.
1996-06-18
Gelder, M ., Koehler, C ., Martin, M ., Anastasiades , P., Hackmann, A, Middleton, H., & Heavons, A. (1988). Tests of a cognitive theory of panic. In I. Hand...Standard Deviations on Subjective and Physiological Resp’onding Measures SUDS P BASE N P A N p B N P c N P o N M 23 4 38 II 27 18 35 10 3 SO 20 13...6, 1996 GIWlUATE F.DUCATIO~ OfFICE /lOI) m ·)91J FU.(JOI)~%.6712 Title of Thesis: Name of Candidate: rEACHING HOSPIl A~S WALTER REED ARMV MEDICAL CENrE
A computerized scheme of SARS detection in early stage based on chest image of digital radiograph
NASA Astrophysics Data System (ADS)
Zheng, Zhong; Lan, Rihui; Lv, Guozheng
2004-05-01
A computerized scheme for early severe acute respiratory syndrome(SARS) lesion detection in digital chest radiographs is presented in this paper. The total scheme consists of two main parts: the first part is to determine suspect lesions by the theory of locally orderless images(LOI) and their spatial features; the second part is to select real lesions among these suspect ones by their frequent features. The method we used in the second part is firstly developed by Katsuragawa et al with necessary modification. Preliminary results indicate that these features are good criterions to tell early SARS lesions apart from other normal lung structures.
Early Mission Maneuver Operations for the Deep Space Climate Observatory
NASA Technical Reports Server (NTRS)
Roberts, Craig; Case, Sara; Reagoso, John
2015-01-01
DSCOVR Lissajous Orbit sized such that orbit track never extends beyond 15 degrees from Earth-Sun line (as seen from Earth). Requiring delta-V maneuvers, control orbit to obey a Solar Exclusion Zone (SEZ) cone of half-angle 4 degrees about the Earth-Sun line. Spacecraft should never be less than 4 degrees from solar center as seen from Earth. Following Lissajous Orbit Insertion (LOI), DSCOVR should be in an opening phase that just skirts the 4-degree SEZ. Maximizes time to the point where a closing Lissajous will require avoidance maneuvers to keep it out of the SEZ. Station keeping maneuvers should take no more than 15 minutes
Causes and Corrections for Propeller-Excited Airborne Noise on a Naval Auxiliary Oiler.
1983-11-01
17 1 sas ri-IMFUtei tii llaii tilt- a,, D) = 01519 (at tip)) ~it., eptalil 1iii0i Ik-%(b ,I all 1 .11 Ill Ill MWi gisi I(il/il \\ ifiratioII Isi ’,~t...slipi aind suet Scopue iii, ltinil. ts r li. 1 It,,Aso, -i trl-rar- ratiorr ii. ) = 12 Thui prirs I it( ,fi - i t l-sigt intiirf riat ioin Ifor I i...gir, rimi- tri isi -tatritr pririlrtii 12:1. ililt-atlios:ii, 11 111 iG-, Ir411ir and %tiiii i il lttfr loi- -2 1 , .11"l tin.1 dtriri ot prrii-livr
[Quetelet, the average man and medical knowledge].
Caponi, Sandra
2013-01-01
Using two books by Adolphe Quetelet, I analyze his theory of the 'average man', which associates biological and social normality with the frequency with which certain characteristics appear in a population. The books are Sur l'homme et le développement de ses facultés and Du systeme social et des lois qui le régissent. Both reveal that Quetelet's ideas are permeated by explanatory strategies drawn from physics and astronomy, and also by discursive strategies drawn from theology and religion. The stability of the mean as opposed to the dispersion of individual characteristics and events provided the basis for the use of statistics in social sciences and medicine.
Quetelet, the average man and medical knowledge.
Caponi, Sandra
2013-01-01
Using two books by Adolphe Quetelet, I analyze his theory of the 'average man', which associates biological and social normality with the frequency with which certain characteristics appear in a population. The books are Sur l'homme et le développement de ses facultés and Du systeme social et des lois qui le régissent. Both reveal that Quetelet's ideas are permeated by explanatory strategies drawn from physics and astronomy, and also by discursive strategies drawn from theology and religion. The stability of the mean as opposed to the dispersion of individual characteristics and events provided the basis for the use of statistics in social sciences and medicine.
1980-09-10
are alphabetized. Omitted from the list is the one relevant host that is not a fish: Necturus m . maculosus (Rafinesque), the Mudpuppy, which is a...macrochirus Rafinesque, Bluegill L. megaictis (Rafinesque), Longear Sunfish Micropterus do lomieui Lac6p~de, Smallmouth Bass M . saimoides (Lac6pbde...89) The field personnel indicated hy their initials in the Exhibits may be identified according to the fol loiing legend. lA -- ldwa rd Amb rog i o M
NASA Astrophysics Data System (ADS)
Marzouk, E. R.; Chenery, S. R.; Young, S. D.
2013-12-01
The Rookhope catchment of Weardale, England, has a diverse legacy of contaminated soils due to extensive lead mining activity over four centuries. We measured the isotopically exchangeable content of Pb, Cd and Zn (E-values) in a large representative subset of the catchment soils (n = 246) using stable isotope dilution. All three metals displayed a wide range of %E-values (c. 1-100%) but relative lability followed the sequence Cd > Pb > Zn. A refinement of the stable isotope dilution approach also enabled detection of non-reactive metal contained within suspended sub-micron (<0.22 μm) colloidal particles (SCP-metal). For most soils, the presence of non-labile SCP-metal caused only minor over-estimation of E-values (<2%) but the effect was greater for soils with particularly large humus or carbonate contents. Approximately 80%, 53% and 66% of the variability in Zn, Cd and Pb %E-values (respectively) could be explained by pH, loss on ignition and total metal content. E-values were affected by the presence of ore minerals at high metal contents leading to an inconsistent trend in the relationship between %E-value and soil metal concentration. Metal solubility, in the soil suspensions used to measure E-values, was predicted using the WHAM geochemical speciation model (versions VI and VII). The use of total and isotopically exchangeable metal as alternative input variables was compared; the latter provided significantly better predictions of solubility, especially in the case of Zn. Lead solubility was less well predicted by either version of WHAM, with over-prediction at low pH and under-prediction at high soil pH values. Quantify the isotopically exchangeable fractions of Zn, Cd and Pb (E-values), and assess their local and regional variability, using multi-element stable isotope dilution, in a diverse range of soil ecosystems within the catchment of an old Pb/Zn mining area. Assess the controlling influences of soil properties on metal lability and develop predictive algorithms for metal lability in the contaminated catchment based on simple soil properties (such as pH, organic matter (LOI), and total metal content). Examine the incidence of non-isotopically-exchangeable metal held within suspended colloidal particles (SCP-metal) in filtered soil solutions (<0.22 μm) by comparing E-values from isotopic abundance in solutions equilibrated with soil and in a resin phase equilibrated with the separated solution. Assess the ability of a geochemical speciation model, WHAM(VII), to predict metal solubility using isotopically exchangeable metal as an input variable.
Impact of a novel phosphorus-nitrogen flame retardant curing agent on the properties of epoxy resin
NASA Astrophysics Data System (ADS)
Liu, Xiaoli; Liang, Bing
2017-12-01
A phosphorus-nitrogen flame retardant curing agent diethyl phosphonic p-Phenylenediamine diamide (DEPPPD) was synthesized. The chemical structure of the obtained compound was identified by Fourier transform infrared (FTIR), 1H nuclear magnetic resonance (1HNMR), and mass spectroscopies. A series of t hermosetting systems were prepared by conventional epoxy resins (E-44) and DEPPPD. The effects of DEPPPD on flame retardancy, thermal degradation behavior, mechanical properties and the morphologies of char residues of EP/DEPPPD thermosets were investigated. The results demonstrated that when the phosphorus content of 2.88 wt%, EP-3 successfully passed UL-94 V-0 flammability rating, the LOI value was as high as 31.1%, the impact strength and tensile strength of it was 6.50 KJ m-2 and 48.21 MPa, the adhesive strength could reach 14.61 MPa, respectively. The TGA results indicated that the introduction of DEPPPD promoted EP matrix decomposed at a lower temperature, the rate of the thermal decomposition also decreased compared with EP-0. The residual char ratio of 800 °C was increased whether in nitrogen or in the air. The morphological structures of char residue were more compact and homogeneous which could prevent the heat transmission and diffusion, limit the production of combustible gases and reduced the heat release rate.
Shafie, Nur Aliaa; Aris, Ahmad Zaharin; Zakaria, Mohamad Pauzi; Haris, Hazzeman; Lim, Wan Ying; Isa, Noorain Mohd
2013-01-01
An investigative study was carried out in Langat River to determine the heavy metal pollution in the sediment with 22 sampling stations selected for the collection of sediment samples. The sediment samples were digested and analyzed for extractable metal ((48)Cd, (29)Cu, (30)Zn, (33)As, (82)Pb) using the Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). Parameters, such as pH, Eh, electrical conductivity (EC), salinity, cation exchange capacity (CEC) and loss on ignition (LOI) were also determined. The assessment of heavy metal pollution was derived using the enrichment factors (EF) and geoaccumulation index (I(geo)). This study revealed that the sediment is predominantly by As > Cd > Pb > Zn > Cu. As recorded the highest EF value at 187.45 followed by Cd (100.59), Pb (20.32), Zn (12.42) and Cu (3.46). This is similar to the I(geo), which indicates that the highest level goes to As (2.2), exhibits moderately polluted. Meanwhile, Cd recorded 1.8 and Pb (0.23), which illustrates that both of these elements vary from unpolluted to moderately polluted. The Cu and Zn levels are below 0, which demonstrates background concentrations. The findings are expected to update the current status of the heavy metal pollution as well as creating awareness concerning the security of the river water as a drinking water source.
Luo, C.; Yang, D.; Peng, Z.; Zhang, Z.; Weiguo, L.; He, J.; Zhou, C.
2008-01-01
A 10.35-m-long sediment core from the Luobei depression in Lop-Nur, Xinjiang, Northwest China, provides detailed information about environmental changes during the Late Pleistocene. The samples taken every 5 cm of the core were analyzed for 10 environmental proxies, including magnetic susceptibility, granularity, chroma, carbonate and loss on ignition (LOI), and pH value. The chronology data are provided by the uranium/thorium disequilibrium dates. The sediments of the section were deposited during the last 32000 years. The results of analysis of 10 proxies were examined using multivariate statistical analysis, and the principal components were calculated. According to the results, the Late Pleistocene sequence contains four climatic and environmental stages appearing in the cycles of cold-wet and warm-dry changes. During 10-9 ka BP, it was the earliest warm episode in the Holocene. Environmental changes in this district were restricted by global change, as suggested by the analysis of glacial-interglacial cycles. But it was different from the mutative trend of a monsoon region in East China because of its own characteristics, which was the situation of cold-wet and warm-dry climate-environment change. The candidate reason may be the uplift of the Tibet Plateau and the westerly wind circulation. ?? Science Press, Institute of Geochemistry, CAS and Springer-Verlag GmbH 2008.
Lissajous Orbit Control for the Deep Space Climate Observatory Sun-Earth L1 Libration Point Mission
NASA Technical Reports Server (NTRS)
Roberts, Craig; Case, Sarah; Reagoso, John
2015-01-01
DSCOVR Lissajous Orbit sized such that orbit track never extends beyond 15 degrees from Earth-Sun line (as seen from Earth). Requiring delta-V maneuvers, control orbit to obey a Solar Exclusion Zone (SEZ) cone of half-angle 4 degrees about the Earth-Sun line. Spacecraft should never be less than 4 degrees from solar center as seen from Earth. Following Lissajous Orbit Insertion (LOI), DSCOVR should be in an opening phase that just skirts the 4-degree SEZ. Maximizes time to the point where a closing Lissajous will require avoidance maneuvers to keep it out of the SEZ. Station keeping maneuvers should take no more than 15 minutes.
New Carbon Dioxide Line Parameters for Atmospheric and High Temperature Applications
1989-10-16
10 LO, z W *0 iZ w 0 0 D V) 0c W +~ 2:.’ 0t -XJ N- O0 0 0 z U- WE 0 2: 0 2: w r-= cc wcccc 0 LOI r 0 3 0w C4o,) 00 0~ U) w cw > ZEC L 4 JZ c0 cc OW...02173 Mr. Charles Randall The Aerospace Corp. (213)366-5977 P.O. Box 92957 Los Angeles, CA 90009 Mr. Peter J. Rayer Dept. of Atmospheric, Oceanic and...National Laboratory (505)667-7672 ESS-5 MS F665 Los Alamos, NM 87545 Dr. Peter Wintersteiner ARCON Corp. (617)890-3330 260 Bear Hill Road Waltham, MA 02154
Altair Descent and Ascent Reference Trajectory Design and Initial Dispersion Analyses
NASA Technical Reports Server (NTRS)
Kos, Larry D.; Polsgrove, Tara T.; Sostaric, Ronald r.; Braden, Ellen M.; Sullivan, Jacob J.; Lee, Thanh T.
2010-01-01
The Altair Lunar Lander is the linchpin in the Constellation Program (CxP) for human return to the Moon. Altair is delivered to low Earth orbit (LEO) by the Ares V heavy lift launch vehicle, and after subsequent docking with Orion in LEO, the Altair/Orion stack is delivered through translunar injection (TLI). The Altair/Orion stack separating from the Earth departure stage (EDS) shortly after TLI and continues the flight to the Moon as a single stack. Altair performs the lunar orbit insertion (LOI) maneuver, targeting a 100-km circular orbit. This orbit will be a polar orbit for missions landing near the lunar South Pole. After spending nearly 24 hours in low lunar orbit (LLO), the lander undocks from Orion and performs a series of small maneuvers to set up for descending to the lunar surface. This descent begins with a small deorbit insertion (DOI) maneuver, putting the lander on an orbit that has a perilune of 15.24 km (50,000 ft), the altitude where the actual powered descent initiation (PDI) commences. At liftoff from Earth, Altair has a mass of 45 metric tons (mt). However after LOI (without Orion attached), the lander mass is slightly less than 33 mt at PDI. The lander currently has a single descent module main engine, with TBD lb(sub f) thrust (TBD N), providing a thrust-to-weight ratio of approximately TBD Earth g's at PDI. LDAC-3 (Lander design and analysis cycle #3) is the most recently closed design sizing and mass properties iteration. Upgrades for loss of crew (LDAC-2) and loss of mission (LDAC-3) have been incorporated into the lander baseline design (and its Master Equipment List). Also, recently, Altair has been working requirements analyses (LRAC-1). All nominal data here are from the LDAC-3 analysis cycle. All dispersions results here are from LRAC-1 analyses.
NASA Astrophysics Data System (ADS)
Kiran Yildirim, Demet; Abdelnasser, Amr; Doner, Zeynep; Kumral, Mustafa
2016-04-01
The Halilar Cu-Pb (-Zn) mineralization that is formed in the volcanogenic metasediments of Bagcagiz Formation at Balikesir province, NW Turkey, represents locally vein-type deposit as well as restricted to fault gouge zone directed NE-SW along with the lower boundary of Bagcagiz Formation and Duztarla granitic intrusion in the study area. Furthermore, This granite is traversed by numerous mineralized sheeted vein systems, which locally transgress into the surrounding metasediments. Therefore, this mineralization closely associated with intense hydrothermal alteration within brecciation, and quartz stockwork veining. The ore mineral assemblage includes chalcopyrite, galena, and some sphalerite with covellite and goethite formed during three phases of mineralization (pre-ore, main ore, and supergene) within an abundant gangue of quartz and calcite. The geologic and field relationships, petrographic and mineralogical studies reveal two alteration zones occurred with the Cu-Pb (-Zn) mineralization along the contact between the Bagcagiz Formation and Duztarla granite; pervasive phyllic alteration (quartz, sericite, and pyrite), and selective propylitic alteration (albite, calcite, epidote, sericite and/or chlorite). This work, by using the mass balance calculations, reports the mass/volume changes (gain and loss) of the chemical components of the hydrothermal alteration zones associated with Halilar Cu-Pb (-Zn) mineralization at Balikesir area (Turkey). It revealed that the phyllic alteration has enrichments of Si, Fe, K, Ba, and LOI with depletion of Mg, Ca, and Na reflect sericitization of alkali feldspar and destruction of ferromagnesian minerals. This zone has high Cu and Pb with Zn contents represents the main mineralized zone. On the other hand, the propylitic zone is characterized by addition of Ca, Na, K, Ti, P, and Ba with LOI and Cu (lower content) referring to the replacement of plagioclase and ferromagnesian minerals by albite, calcite, epidote, and sericite with chlorite. Keywords: Mass balance calculations; hydrothermal alterations; Cu-Pb (-Zn) mineralization; Halilar area; NW Turkey
NASA Astrophysics Data System (ADS)
Wang, Y.; Finney, B.; Wooller, M. J.
2007-12-01
Several techniques are available to examine the isotopic composition of historic lake waters, providing data that can subsequently be used to examine environmental changes. Recently-developed techniques are the stable oxygen isotope analysis of subfossil chironomid (Diptera: Chironomidae) head capsules (mostly chitin) preserved in lake sediments and stable hydrogen isotope analyses directly on bulk sediments. An advantage of using δ18O of chironomids is that the chitinous chironomid headcapsules preserve well in lake sediments, retaining the stable oxygen isotope signature of the lake in which they lived. An advantage of δD analyses of bulk sediments is that a sediment core can be analyzed relatively easily and when the %C (total organic carbon) and %H profiles correlate the data can be used to infer past δD changes of the organics in the sediments. We present results from these analyses of a lake sediment core from Idavain Lake (58°46'N, 155°57'W, 223m above sea level) in southwest Alaska in concert with other paleolimnological proxies, including δ15N, δ13C, LOI, magnetic susceptibility, organic content and opal concentrations for a better understanding of paleolimnological changes since deglaciation for the region. Our preliminilary result shows that downcore shifts of δ18O analyzed from chironomid head capsules coincide well with LOI and pollen changes. The δD of sediments and TOM showed large magnitude changes and reflected the relative lake level changes during the record. This study aim to test the correlation between stable isotope analyese on chiornomid head capsules, lake water, and bulk sediments. In the addition, our study will add to the relatively small database of paleoenvironmental reconstructions from terrestrial sites in Southwest Alaska.
NASA Astrophysics Data System (ADS)
Jacob, Rhys; Trout, Neil; Raud, Ralf; Clarke, Stephen; Steinberg, Theodore A.; Saman, Wasim; Bruno, Frank
2016-05-01
In an effort to reduce the cost and increase the material compatibility of encapsulated phase change materials (EPCMs) a new encapsulated system has been proposed. In the current study a molten salt eutectic of barium chloride (53% wt.), potassium chloride (28% wt.) and sodium chloride (19% wt.) has been identified as a promising candidate for low cost EPCM storage systems. The latent heat, melting point and thermal stability of the phase change material (PCM) was determined by DSC and was found to be in good agreement with results published in the literature. To cope with the corrosive nature of the PCM, it was decided that a fly-ash based geopolymer met the thermal and economic constraints for encapsulation. The thermal stability of the geopolymer shell was also tested with several formulations proving to form a stable shell for the chosen PCM at 200°C and/or 600°C. Lastly several capsules of the geopolymer shell with a chloride PCM were fabricated using a variety of methods with several samples remaining stable after exposure to 600°C testing.
Five years of full-scale utility demonstration of pulsed energization of electric precipitators
DOE Office of Scientific and Technical Information (OSTI.GOV)
Schultz, S.A.; Jacobus, P.L.; Casey, P.J.
1996-11-01
In a conventional electrostatic precipitator (ESP) the applied dc voltage fulfills three functions: (1) generation of negative ions, (2) charging of particles, and (3) transport of the charged particles to the collecting plates. In the case of high resistivity fly-ash (often associated with the burning of low sulfur coal) the dc voltage is limited by repeated electrical discharges and in extreme cases by back-corona. Lowering the applied dc voltage reduces sparking and back-corona, but also reduces the field on the discharge wires and leads to poorly distributed ion generation as well as reduced charging and particle transport forces. Pulsed energization,more » which consists of superimposing high voltage pulses of short duration onto the existing base dc voltage, offers an attractive way to improve the collection efficiency of ESPs suffering from poor energization. The superimposed pulses become responsible for uniform ion generation while the underlying dc field continues to fulfill the function of particle charging and transport. This paper describes the five-year test of the ESP at Madison Gas and Electric`s Blount Station.« less
NASA Astrophysics Data System (ADS)
Singh, Ashish Kumar; Patil, Balu; Hoffmann, Niklas; Saltonstall, Brooks; Doddamani, Mrityunjay; Gupta, Nikhil
2018-03-01
This work focuses on developing filaments of high-density polyethylene (HDPE) and their hollow particle-filled syntactic foams for commercial three-dimensional (3D) printers based on fused filament fabrication technology. Hollow fly-ash cenospheres were blended by 40 wt.% in a HDPE matrix to produce syntactic foam (HDPE40) filaments. Further, the recycling potential was studied by pelletizing the filaments again to extrude twice (2×) and three times (3×). The filaments were tensile tested at 10-4 s-1, 10-3 s-1, and 10-2 s-1 strain rates. HDPE40 filaments show an increasing trend in modulus and strength with the strain rate. Higher density and modulus were noticed for 2× filaments compared to 1× filaments because of the crushing of some cenospheres in the extrusion cycle. However, 2× and 3× filament densities are nearly the same, showing potential for recycling them. The filaments show better properties than the same materials processed by conventional injection molding. Micro-CT scans show a uniform dispersion of cenospheres in all filaments.
Industrial waste utilization for foam concrete
NASA Astrophysics Data System (ADS)
Krishnan, Gokul; Anand, K. B.
2018-02-01
Foam concrete is an emerging and useful construction material - basically a cement based slurry with at least 10% of mix volume as foam. The mix usually containing cement, filler (usually sand) and foam, have fresh densities ranging from 400kg/m3 to 1600kg/m3. One of the main drawbacks of foam concrete is the large consumption of fine sand as filler material. Usage of different solid industrial wastes as fillers in foam concrete can reduce the usage of fine river sand significantly and make the work economic and eco-friendly. This paper aims to investigate to what extent industrial wastes such as bottom ash and quarry dust can be utilized for making foam concrete. Foam generated using protein based agent was used for preparing and optimizing (fresh state properties). Investigation to find the influence of design density and air-void characteristics on the foam concrete strength shows higher strength for bottom ash mixes due to finer air void distribution. Setting characteristics of various mix compositions are also studied and adoption of Class C flyash as filler demonstrated capability of faster setting.
Razi, Putri Zulaiha; Abdul Razak, Hashim; Khalid, Nur Hafizah A
2016-05-06
This study investigates the engineering performance and CO₂ footprint of mortar mixers by replacing Portland cement with 10%, 20%, 40% and 60% fly ash, a common industrial waste material. Samples of self-compacting mortar (SCM) were prepared with four different water/binder ratios and varying dosages of superplasticizer to give three ranges of workability, i.e. , normal, high and self-compacting mortar mix. The engineering performance was assessed in term of compressive strength after designated curing periods for all mixes. CO₂ footprint was the environmental impact indicator of each production stage. The optimum mix obtained was at 10% replacement rate for all mixes. Total production emission reduced by 56% when the fly ash replacement rate increased from 0% to 60% (maximum). This is translated to a reduction of 80% in eco-points (assuming that the energy consumption rate of production with 0% fly ash is at 100%). Such re-utilization is encouraged since it is able to reduce possible soil toxicity due to sulfur leaching by 5% to 27% and landfill area by 15% to 91% on average.
Razi, Putri Zulaiha; Abdul Razak, Hashim; Khalid, Nur Hafizah A.
2016-01-01
This study investigates the engineering performance and CO2 footprint of mortar mixers by replacing Portland cement with 10%, 20%, 40% and 60% fly ash, a common industrial waste material. Samples of self-compacting mortar (SCM) were prepared with four different water/binder ratios and varying dosages of superplasticizer to give three ranges of workability, i.e., normal, high and self-compacting mortar mix. The engineering performance was assessed in term of compressive strength after designated curing periods for all mixes. CO2 footprint was the environmental impact indicator of each production stage. The optimum mix obtained was at 10% replacement rate for all mixes. Total production emission reduced by 56% when the fly ash replacement rate increased from 0% to 60% (maximum). This is translated to a reduction of 80% in eco-points (assuming that the energy consumption rate of production with 0% fly ash is at 100%). Such re-utilization is encouraged since it is able to reduce possible soil toxicity due to sulfur leaching by 5% to 27% and landfill area by 15% to 91% on average. PMID:28773465
NASA Astrophysics Data System (ADS)
Uno, M.; Nakamura, H.; Iwamori, H.
2011-12-01
Individual parcel of regional metamorphic rock records physico-chemical conditions such as P-T path, mass transfer and deformation with the Lagrangian specification. On the other hand, a metamorphic belt as an ensemble of such parcels may provide a large-scale flow field of energy (e.g., temperature, entropy) and mass (including both solid and fluid phases with elements and isotopes) with the Eulerian specification. However, there is so far few model that integrates all the variables stated above. Phase petrology provides mostly the intensive variables (e.g., P-T path), whereas geochemistry provides mostly the extensive variables (time-integrated mass transfer), and these two have been treated separately. Here we combine phase petrology and geochemistry from a scale of mineral grain, and solve them under a simultaneous and consistent set of thermodynamic and mass balance equation. For this sake, the Sanbagawa metamorphic belt in Japan has been surveyed. To understand the nature of fluid during rehydration, we analyzed both basic rocks and pelitic rocks that record retrograde reactions. Major and trace element compositions of each mineral, and bulk rock chemistry have been analyzed with EPMA, LA-ICP-MS, XRF and ICP-MS, respectively. Retrograde P-T path and the extent of rehydration of each rock have been obtained by applying the Gibbs' method (e.g. Spear, 1993; Okamoto&Toriumi, 2001) to amphiboles. Trace element budget along a specific P-T path were calculated by equating differential mass balance equation for major and trace elements as follows; XfluiddMfluid = ⊙MsolidXsolid + ⊙XsoliddMsolid Where the X and M denotes compositions and modes of minerals and dX and dM are their changes along a specific P-T change. The mineral compositions (Xsolid), mineral modes (Msolid), mineral growths (dMsolid) for zoned minerals (amphibole and/or garnet) and fluid compositions (Xfluid) were derived from the results of Gibbs' method, X-ray map and fluid/mineral partition coefficients, respectively. Thus, the unknowns are dMs, and the equations are solved for them. As a result, the mass transfer during the specific P-T change (Xfluid dMfluid) can be specified. It is revealed that fluid mobile elements such as LIL elements, Sr and Pb are mostly proportional to LOI (loss on ignition). LOI and extent of rehydration is proportional in the Sanbagawa belt (Okamoto&Toriumi, 2005), thus the observed enrichment of LILE, Sr and Pb are interpreted to be associated with rehydration. The Sr isotope ratios of the basic shists also increase with LOI, implying that the differences in bulk rock chemistry are not attributed to differences in mineral modes,but addition and/or reaction with external source of fluids with high 87Sr/86Sr. The estimated fluid composition is similar to calculated compositions of slab-derived fluids (Nakamura et al., 2008). From mass balance calculation, trace element budget associated with rehydration reactions and their spatial distribution will be presented, and the mechanisms of mass and fluid transfer will be discussed.
1984-07-01
TOTAL TON-HILES, 8,4110.310. SALEM HAR304, "A38. SECTION INCLUI3ED, WESTERLY SHORE OF MA44514 INCLUDINJG SOUTH RIVER. CnNTRT)LL 14...444074 400 eoToo COAO00LO, 10 40lOI O0 , PFA , ,1 6 FOOT 0’) £OCfAGF A0O,. ALL AT OAN I W aATEO* PPTJECT 10E4004 1.9 k )l.A rqOvAOAyTVf STATFOFNT mo...OLOWANS CREEK, N. J. UP~okiNfl moovnPLINA TOTAL, 6 AND LESS - 9 PEPPER CREEK, DEL. NOl WE SiL 10RIP REPORT1 .U SALEM RI VER, I..* uPON 0 oINPOUND TOT ALI
Fire-retardant decorative inks for aircraft interiors
NASA Technical Reports Server (NTRS)
Kourtides, D. A.; Nir, Z.; Mikroyannidis, J. A.
1985-01-01
Commercial and experimental fire retardants were screened as potential fire retardants for acrylic printing inks used on aircraft interior sandwich panels. The fire retardants are selected according to their physical properties and their thermostabilities. A criterion for selecting a more stable fire retardant is established. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) are used to determine thermostabilities. Results show that the fire retardant formulations are more thermally stable than the acrylic ink control. It is determined that an ink formulation containing a brominated phenol and carboxy-terminated butadiene acrylonitrile which has been modified with a brominated polymeric additive (BPA), yields the highest limiting oxygen index (LOI) of all the compounds tested. All of the fire-retardant formulations have a higher oxygen index than the baseline acrylic ink.
Chu, Steven [U.S. Energy Secretary
2018-01-12
The winners for 2011 of the Department of Energy's Ernest Orlando Lawrence Award were recognized in a ceremony held May 21, 2012. Dr. Steven Chu and others spoke of the importance of the accomplishments and the prestigious history of the award. The recipients of the Ernest Orlando Lawrence Award for 2011 are: Riccardo Betti (University of Rochester); Paul C. Canfield (Ames Laboratory); Mark B. Chadwick (Los Alamos National Laboratory); David E. Chavez (Los Alamos National Laboratory); Amit Goyal (Oak Ridge National Laboratory); Thomas P. Guilderson (Lawrence Livermore National Laboratory); Lois Curfman McInnes (Argonne National Laboratory); Bernard Matthew Poelker (Thomas Jefferson National Accelerator Facility); and Barry F. Smith (Argonne National Laboratory).
[Montesquieu visually impaired, then blind (January 1689- February 1755)].
Battin, Jacques
2014-01-01
The correspondence of Montesquieu published by the Oxford Foundation informs about visual disorders of the founder of the socio-political science. The examination of his bust's face done by J.B. Lemoyne reveals a divergent squint of the left eye; the one with which he fold that he only could see big objects. This amblyopia was a premature and prolonged embarrassment. During the last ten years of his life, from 1748, date of publication of the Esprit des lois up to his death in 1755 he was blind because of the cataract of the other eye. He has not able to bust in surgery, while the French surgeon Jacques Daviel already proceeded to the extraction of the lens as we do it nowadays.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Chu, Steven
The winners for 2011 of the Department of Energy's Ernest Orlando Lawrence Award were recognized in a ceremony held May 21, 2012. Dr. Steven Chu and others spoke of the importance of the accomplishments and the prestigious history of the award. The recipients of the Ernest Orlando Lawrence Award for 2011 are: Riccardo Betti (University of Rochester); Paul C. Canfield (Ames Laboratory); Mark B. Chadwick (Los Alamos National Laboratory); David E. Chavez (Los Alamos National Laboratory); Amit Goyal (Oak Ridge National Laboratory); Thomas P. Guilderson (Lawrence Livermore National Laboratory); Lois Curfman McInnes (Argonne National Laboratory); Bernard Matthew Poelker (Thomas Jeffersonmore » National Accelerator Facility); and Barry F. Smith (Argonne National Laboratory).« less
DOE Office of Scientific and Technical Information (OSTI.GOV)
Hughes, E. Tillman, D.
1997-12-01
Biomass utilization to reduce fossil C0{sub 2} emissions is being supported by sixteen (16) EPRI research projects, each contributing to the commercialization of systems to address greenhouse gas emissions. These projects include: (1) cofiring combustion testing at the Seward Generating Station of GPU Genco; (2) fuel preparation testing at the Greenidge Generating Station of NYSEG; (3) precommercial testing of cofiring at the Allen and Colbert Fossil Plants of TVA; (4) testing of switchgrass cofiring at the Blount St. Station of Madison Gas & Electric; (5) high percentage biomass cofiring with Southern Company; (6) urban wood waste cofiring at the supercriticalmore » cyclone boiler at Michigan City Generating Station of Northern Indiana Public Service Co. (NIPSCO); (7) evaluation of switchgrass cofiring with Nebraska Public Power District at Sandia National Laboratories in Livermore, CA; (8) waste plastics cofiring with Duke Power in a tangentially-fired pulverized coal (PC) boiler; (9) cofiring a mixture of plastics, fiber, and pulp industry wastes with South Carolina Electric and Gas; (10) urban wood waste cofiring evaluation and testing by the University of Pittsburgh in stoker boilers; (11) assessment of toxic emissions from cofiring of wood and coal; (12) development of fuel and power plant models for analysis and interpretation of cofiring results; (13) analysis of C0{sub 2} utilization in algal systems for wastewater treatment; (14) combustion testing and combustor development focusing on high percentage cofiring; (15) analysis of problems and potential solutions to the sale of flyash from coal- fired boilers practicing cofiring; and (16) analysis of C0{sub 2} capture and disposal systems. EPRI is supported in these efforts by numerous contractors including: Foster Wheeler Environmental Corporation, Battelle Columbus Laboratories, New York State Electric and Gas Co., Tennessee Valley Authority (TVA), NIPSCO, the University of Pittsburgh, John Benneman, and others. These projects address various aspects of cofiring for C0{sub 2} mitigation including testing of cofiring with various fuels, and in all types of boilers; development of analytical tools to support the cofiring assessment; addressing specific barriers to cofiring such as the sale of flyash; longer term technology development; and evaluating alternative methods for C0{sub 2} mitigation. Taken together, they address the critical concerns associated with this approach to biofuel utilization. As such, they support implementation of the most promising near-term approach to biomass usage for greenhouse gas mitigation. This report contains a brief description of each project. It then reports the progress made during the first quarter of the contract, focusing upon test results from the Allen Fossil Plant, where precommercial testing at a cyclone boiler was used to evaluate particle size and NO{sub x} emissions from cofiring.« less
Zhang, Daohai; He, Min; He, Weidi; Zhou, Ying; Qin, Shuhao; Yu, Jie
2017-01-01
In this work, the long glass fibre-reinforced poly(butylene terephthalate) (PBT) composites filled with 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) were prepared by melt blending, and the influence of thermo-oxidative ageing on the static and dynamic mechanical properties, thermal behaviours and morphology of composites with different ageing time at 120 °C were investigated and analysed. The results showed that the mechanical properties decreased in the primary stage of ageing, while embrittlement occurs in the later period, and the crystallinity of PBT decreases first, and then recovers to some extent. The scanning electron microscopy (SEM) photos of the samples indicated that the obvious crack appeared on the sample surface and a deeper, broader crack occurred with a longer ageing time. The results of energy dispersive X-ray analysis (EDAX) proved the DOPO filler diffused to the sample surface by measuring the content of phosphorus. Thermal gravimetric analysis (TGA) curves showed that the thermal stabilities of composites increased with longer ageing time, as did the values of the limited oxygen index (LOI). Meanwhile, the results of dynamic mechanical analysis (DMA) indicated that the glass transition temperature shifted to a higher temperature after ageing due to the effect of crosslinking, and both the crosslinking and degradation of PBT molecular chains act as the main factors in the whole process of thermo-oxidative ageing. PMID:28772860
Leitner, Simon; Reichenauer, Thomas G; Watzinger, Andrea
2018-02-15
The evaluation of groundwater contaminant e.g. tetrachloroethene (PCE) degradation processes requires complete quantification of and pathway analysis of the groundwater contaminant under investigation. For example the reduction of PCE concentrations in the groundwater by unknown dissolution and/or sorption processes will impede interpretation of the fate and behaviour of such contaminants. In the present study PCE dissolution and sorption processes during anaerobic microbial degradation of chlorinated ethenes were investigated. For this purpose, microcosms were prepared using sediment samples from a PCE-contaminated aquifer, which in previous studies had demonstrated anaerobic organohalide respiration of PCE. Solid/water distribution coefficients (k d ) of PCE were determined and validated by loss-on-ignition (LOI) and PCE sorption experiments. The determined k d magnitudes indicated methodological congruency, yielding values for sediment samples within a range of 1.15±0.02 to 5.93±0.34L·kg -1 . The microcosm experiment showed lower PCE concentrations than expected, based on spiked PCE and observed anaerobic microbial degradation processes. Nevertheless the amount of PCE spike added was completely recovered albeit in the form of lower chlorinated metabolites. A delay due to dissolution processes was not responsible for this phenomenon. Sorption to sediments could only partially explain the reduction of PCE in the water phase. Accordingly, the results point to reversible sorption processes of PCE, possibly onto bacterial cell compartments and/or exopolymeric substances. Copyright © 2017 Elsevier B.V. All rights reserved.
Larsen, M.C.
2000-01-01
During the period from 1990 to 1997, annual rainfall accumulation averaged 87% of normal at the 12 stations with the longest period of record in Puerto Rico, a Caribbean island with a 1999 population of 3.8 million. Streamflow in rivers supplying the La Plata and Loi??za reservoirs, the principal water supply of the San Juan metropolitan area, was at or below the 10th flow percentile for 27% to 50% of the time between December 1993 and May 1996. Diminished reservoir levels in 1994 and 1995 affected more than 1 million people in the San Juan metropolitan area. Water rationing was implemented during this period and significant agricultural losses, valued at $165 million, were recorded in 1994. The public endured a year of mandatory water rationing in which sections of the city had their water-distribution networks shut off for 24 to 36 hours on alternate days. During the winter and spring of 1997-1998, water was rationed to more than 200,000 people in northwestern Puerto Rico because water level in the Guajataca reservoir was well below normal for two years because of rainfall deficits. The drought period of 1993-1996 was comparable in magnitude to a drought in 1966-1968, but water rationing was more severe during the 1993-1996 period, indicating that water management issues such as demand, storage capacity, water production and losses, and per capita consumption are increasingly important as population and development in Puerto Rico expand.
Zhang, Daohai; He, Min; He, Weidi; Zhou, Ying; Qin, Shuhao; Yu, Jie
2017-05-04
In this work, the long glass fibre-reinforced poly(butylene terephthalate) (PBT) composites filled with 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) were prepared by melt blending, and the influence of thermo-oxidative ageing on the static and dynamic mechanical properties, thermal behaviours and morphology of composites with different ageing time at 120 °C were investigated and analysed. The results showed that the mechanical properties decreased in the primary stage of ageing, while embrittlement occurs in the later period, and the crystallinity of PBT decreases first, and then recovers to some extent. The scanning electron microscopy (SEM) photos of the samples indicated that the obvious crack appeared on the sample surface and a deeper, broader crack occurred with a longer ageing time. The results of energy dispersive X-ray analysis (EDAX) proved the DOPO filler diffused to the sample surface by measuring the content of phosphorus. Thermal gravimetric analysis (TGA) curves showed that the thermal stabilities of composites increased with longer ageing time, as did the values of the limited oxygen index (LOI). Meanwhile, the results of dynamic mechanical analysis (DMA) indicated that the glass transition temperature shifted to a higher temperature after ageing due to the effect of crosslinking, and both the crosslinking and degradation of PBT molecular chains act as the main factors in the whole process of thermo-oxidative ageing.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Feihu Li; Jianping Zhai; Xiaoru Fu
2006-08-15
The chemistry, mineralogy, morphology, and particle size distribution were investigated in fly ashes from the burning of Datong (ShanXi, China) bituminous coal and the cofiring of Mideast high-sulfur petroleum coke (PC) with 30:70 (cal %) and 50:50 (cal %) blends of Datong bituminous coal in two commercial CFBC boilers. With the exception of CaO, the amounts of major oxides in the fly ashes from cofiring PC and coal were close to those of the common coal fly ashes. The PC-coal fly ashes were enriched in Ni, V, and Mo, implying these trace elements were mainly derived from PC. Ni andmore » V, along with several other elements, such as Cr, Cu, Se, Pb, U, Th, and possibly As and Cd, increased in content with a decrease in temperature of the electrostatic precipitator (ESP). The results of chemistry, mineralogy, and morphology studies suggested that the desulfurization rate of the CFBC boilers at current conditions was low, and the PC tends to coarsen the fly ash particles and increase the loss on ignition (LOI) values, making these fly ashes unsuitable for use as a cement additive or a mineral admixture in concrete. Further studies on the combustion status of the CFBC boilers are needed if we want to be able to increase the desulfurization rate and produce high-quality fly ashes for broader and full utilization. 22 refs., 4 figs., 4 tabs.« less
NASA Astrophysics Data System (ADS)
Sheng, Haibo; Zhang, Yan; Wang, Bibo; Yu, Bin; Shi, Yongqian; Song, Lei; Kundu, Chanchal Kumar; Tao, Youji; Jie, Ganxin; Feng, Hao; Hu, Yuan
2017-04-01
Microencapsulated ammonium polyphosphate (MCAPP) in combination with polyester polyurethane (TPU) was used to flame retardant ethylene-vinyl acetate copolymer (EVA). The EVA composites with different irradiation doses were immersed in hot water (80 °C) to accelerate ageing process. The microencapsulation and irradiation dose ensured positive impacts on the properties of the EVA composites in terms of better dimensional stability and flame retardant performance. The microencapsulation of APP could lower its solubility in water and the higher irradiation dose led to the more MCAPP immobilized in three dimensional crosslinked structure of the EVA matrix which could jointly enhance the flame retardant and electrical insulation properties of the EVA composites. So, the EVA composites with 180 kGy irradiation dose exhibited better dimensional stability than the EVA composites with 120 kGy due to the higher crosslinking degree. Moreover, the higher irradiation dose lead to the more MCAPP immobilizated in crosslinked three-dimensional structure of EVA, enhancing the flame retardancy and electrical insulation properties of the EVA composites. After ageing test in hot water at 80 °C for 2 weeks, the EVA/TPU/MCAPP composite with 180 kGy could still maintain the UL-94 V-0 rating and the limiting oxygen index (LOI) value was as high as 30%. This investigation indicated the flame retardant EVA cable containing MCAPP could achieve stable properties and lower electrical fire hazard risk during long-term hot water ageing test.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Washington, Aaron L.; Narrows, William; Christian, Jonathan H.
During Decommissioning and Demolition (D&D) activities at SRS, it is important that the building be screened for radionuclides and heavy metals to ensure that the proper safety and disposal metrics are in place. A major source of contamination at DOE facilities is the accumulation of mercury contamination, from nuclear material processing and Liquid Waste System (LWS). This buildup of mercury could possibly cause harm to any demolition crew or the environment should this material be released. The current standard method is to take core samples in various places in the facility and use X-ray fluorescence (XRF) to detect the contamination.more » This standard method comes with a high financial value due to the security levels of these sample facilities with unknown contamination levels. Here in we propose the use of portable XRF units to detect for this contamination on-site. To validate this method, the instrument has to be calibrated to detect the heavy metal contamination, be both precise with the known elemental concentrations and consistent with its actual results of a sample concrete and pristine contaminant, and be able to detect changes in the sample concrete’s composition. After receiving the various concrete samples with their compositions found by a XRF wave-dispersive method, the calibration factor’s linear regressions were adjusted to give the baseline concentration of the concrete with no contamination. Samples of both concrete and concrete/flyash were evaluated; their standard deviations revealed that the measurements were consistent with the known composition. Finally, the samples were contaminated with different concentrations of sodium tungsten dihydrate, allowed to air dry, and measured. When the contaminated samples were analyzed, the heavy metal contamination was seen within the spectrum of the instrument, but there was not a trend of quantification based on the concentration of the solution.« less
Fly ash zeolite catalyst support for Fischer-Tropsch synthesis
NASA Astrophysics Data System (ADS)
Campen, Adam
This dissertation research aimed at evaluating a fly ash zeolite (FAZ) catalyst support for use in heterogeneous catalytic processes. Gas phase Fischer-Tropsch Synthesis (FTS) over a fixed-bed of the prepared catalyst/FAZ support was identified as an appropriate process for evaluation, by comparison with commercial catalyst supports (silica, alumina, and 13X). Fly ash, obtained from the Wabash River Generating Station, was first characterized using XRD, SEM/EDS, particle size, and nitrogen sorption techniques. Then, a parametric study of a two-step alkali fusion/hydrothermal treatment process for converting fly ash to zeolite frameworks was performed by varying the alkali fusion agent, agent:flyash ratio, fusion temperature, fused ash/water solution, aging time, and crystallization time. The optimal conditions for each were determined to be NaOH, 1.4 g NaOH: 1 g fly ash, 550 °C, 200 g/L, 12 hours, and 48 hours. This robust process was applied to the fly ash to obtain a faujasitic zeolite structure with increased crystallinity (40 %) and surface area (434 m2/g). Following the modification of fly ash to FAZ, ion exchange of H+ for Na+ and cobalt incipient wetness impregnation were used to prepare a FTS catalyst. FTS was performed on the catalysts at 250--300 °C, 300 psi, and with a syngas ratio H2:CO = 2. The HFAZ catalyst support loaded with 11 wt% cobalt resulted in a 75 % carbon selectivity for C5 -- C18 hydrocarbons, while methane and carbon dioxide were limited to 13 and 1 %, respectively. Catalyst characterization was performed by XRD, N2 sorption, TPR, and oxygen pulse titration to provide insight to the behavior of each catalyst. Overall, the HFAZ compared well with silica and 13X supports, and far exceeded the performance of the alumina support under the tested conditions. The successful completion of this research could add value to an underutilized waste product of coal combustion, in the form of catalyst supports in heterogeneous catalytic processes.
1985-01-01
N 0 mC. m.( m( m0 C) (0 (0 (0 0 Nf.0 r. cNNr4NO (0 en (0 MSP (0 *50 -W (0 -1 0 0 0 0 NC) 000 0 "-4 0 I(( (0 (1 1) P7 L) (0 in 4. -.4-4 m -& (D U (0... acCA -4N NN CcC4c xC4 NN N4 10L 0 ( Z-4 -I 4N . ".. (0 N 1-.U -4 .4 co -lOI m a) a) mne M 0. N r. I0 I0 I 0- 0. nc c n CI C% 004 0 00 0 04 " "N . .0
GLOBE Hydrology Workshop SEIP program
NASA Technical Reports Server (NTRS)
2005-01-01
Matt Krigbaum (left), a teacher at Mitchell Elementary in Ann Arbor, Mich., pours water from the Pearl River into a turbidity tube to measure the river's light penetration. Krigbaum, along with Lois Williams, principal at Elizabeth Courville Elementary in Detroit, Mich.; and Carolyn Martin and Arlene Wittmer, teachers at Elizabeth Courville Elementary; conducted the experiment during a GLOBE (Global Learning and Observations to Benefit the Environment) hydrology workshop. GLOBE is a worldwide, hands-on science education program in which teachers can become certified to implement the program at their schools after taking hydrology, land cover/biology, atmosphere/climate and soil protocol workshops. Twelve teachers from across the country attended the recent weeklong GLOBE training at SSC, offered through its Educator Resource Center and the NASA Explorer Schools program. All workshops are free and offer continuing education units.
GLOBE Hydrology Workshop SEIP program
2005-06-30
Matt Krigbaum (left), a teacher at Mitchell Elementary in Ann Arbor, Mich., pours water from the Pearl River into a turbidity tube to measure the river's light penetration. Krigbaum, along with Lois Williams, principal at Elizabeth Courville Elementary in Detroit, Mich.; and Carolyn Martin and Arlene Wittmer, teachers at Elizabeth Courville Elementary; conducted the experiment during a GLOBE (Global Learning and Observations to Benefit the Environment) hydrology workshop. GLOBE is a worldwide, hands-on science education program in which teachers can become certified to implement the program at their schools after taking hydrology, land cover/biology, atmosphere/climate and soil protocol workshops. Twelve teachers from across the country attended the recent weeklong GLOBE training at SSC, offered through its Educator Resource Center and the NASA Explorer Schools program. All workshops are free and offer continuing education units.
1991-01-08
10Ito 9 O.rQ t~~l.Itid the timew fW r~IwF’lnut~ = 101144 "’stfl da fta ~W Reifvged wA~t4.nn- j this data h.eadŘd ad npJet-,,q and .ne,..n 114 I O=IIr.O...baughman, Dr. lDrivid it. Ibeudeir, Ihatherine l3lauer, James HI. 13yrn, Lois J . Carey and Mary B. Leveriing; ~nigahc of Library Customers 1990-2000, by Dr...Philip Ad.D 8011n-dtir; Libra ries in the Nineties and beyond, by Dr. TIhomas J . cialvin; I.-eadk’rshim Ill thom 90’s, by B~rooke E~. Sheldon
Nery, José Reinaldo Cardoso; Bonotto, Daniel Marcos
2011-04-01
Activity profiles of excess (210)Pb determined in three sediment cores from Amazon River mouth, Macapá city, Brazil, provided the evaluation of sedimentation rates, contributing to a better knowledge of the hydrological conditions in the site that is the capital of Amapá State and is drained by the waters of the huge Amazon River. Chemical data were also determined in the sediments, allowing identify signatures coupled to anthropogenic inputs held in the past in Amapá State. Significant direct relationships between LOI (loss on ignition) and organic matter were found for all sediments profiles. Silica was found to be inversely related to organic matter in the three profiles; its decrease accompanied an increase on the specific surface of the sediments. This relationship was confirmed by a great number of inverse significant correlations among silica and oxides Na(2)O, K(2)O, CaO, MgO, Al(2)O(3), P(2)O(5), Fe(2)O(3) and MnO. It was possible to identify the role of organic matter on adsorption of several oxides in the core sediments profiles. Apparent sediment mass accumulation rates corresponding to values between 450 and 2510 mg cm(-2)yr(-1) were obtained, and are compatible with the results of others studies. The (210)Pb activities in one sampling point suggested the occurrence of anthropogenic inputs related to the initial period of the mining activities conducted in Serra do Navio, Amapá State, for the commercialization of Mn ores. This was reinforced by the abrupt fluctuations in chemical data obtained for the sediments and composition of the interstitial waters occurring there. The Atlantic hurricane activity also appeared to affect the sedimentation rates in the area, as two different values were recorded in each profile. Copyright © 2011 Elsevier Ltd. All rights reserved.
Integrated NO{sub x} control at New England Power, Salem Harbor Station
DOE Office of Scientific and Technical Information (OSTI.GOV)
Frish, M.B.; Johnson, S.A.; Comer, J.P.
Selective non-catalytic reduction (SNCR) is a viable technology for reducing NO{sub x} emissions from coal-fired boilers, especially those older units where large capital expenditures for alternative technologies may not be justified. However, NO{sub x} reduction efficiency of the SNCR process is maximized when the proper amount of reagent is injected at the proper temperature and dispersed rapidly enough to avoid ammonia slip. Early NEP experience at Salem Harbor station indicated that NO{sub x} reductions of 60% were achievable with SNCR. However, less NO{sub x} reductions were tolerated to avoid NH{sub 3} slip and subsequent flyash contamination and visible stack plumemore » resulting from excess ammonia. Preliminary tests by PSI Environmental showed that ammonia slip could be monitored in real time using their patented SpectraScan{trademark}-NH{sub 3} instrument, and that furnace exit temperature could be continuously monitored and controlled using GasTemp{trademark} another PSI Environmental product. Based on this information, detailed tests were planned to show integrated control over the SNCR process. A goal of the project was to achieve lower NO{sub x} with less reagent! This paper describes the status of the project.« less
An extrapolation method for compressive strength prediction of hydraulic cement products
DOE Office of Scientific and Technical Information (OSTI.GOV)
Siqueira Tango, C.E. de
1998-07-01
The basis for the AMEBA Method is presented. A strength-time function is used to extrapolate the predicted cementitious material strength for a late (ALTA) age, based on two earlier age strengths--medium (MEDIA) and low (BAIXA) ages. The experimental basis for the method is data from the IPT-Brazil laboratory and the field, including a long-term study on concrete, research on limestone, slag, and fly-ash additions, and quality control data from a cement factory, a shotcrete tunnel lining, and a grout for structural repair. The method applicability was also verified for high-performance concrete with silica fume. The formula for predicting late agemore » (e.g., 28 days) strength, for a given set of involved ages (e.g., 28,7, and 2 days) is normally a function only of the two earlier ages` (e.g., 7 and 2 days) strengths. This equation has been shown to be independent on materials variations, including cement brand, and is easy to use also graphically. Using the AMEBA method, and only needing to know the type of cement used, it has been possible to predict strengths satisfactorily, even without the preliminary tests which are required in other methods.« less
Level 1 environmental assessment performance evaluation. Final report jun 77-oct 78
DOE Office of Scientific and Technical Information (OSTI.GOV)
Estes, E.D.; Smith, F.; Wagoner, D.E.
1979-02-01
The report gives results of a two-phased evaluation of Level 1 environmental assessment procedures. Results from Phase I, a field evaluation of the Source Assessment Sampling System (SASS), showed that the SASS train performed well within the desired factor of 3 Level 1 accuracy limit. Three sample runs were made with two SASS trains sampling simultaneously and from approximately the same sampling point in a horizontal duct. A Method-5 train was used to estimate the 'true' particulate loading. The sampling systems were upstream of the control devices to ensure collection of sufficient material for comparison of total particulate, particle sizemore » distribution, organic classes, and trace elements. Phase II consisted of providing each of three organizations with three types of control samples to challenge the spectrum of Level 1 analytical procedures: an artificial sample in methylene chloride, an artificial sample on a flyash matrix, and a real sample composed of the combined XAD-2 resin extracts from all Phase I runs. Phase II results showed that when the Level 1 analytical procedures are carefully applied, data of acceptable accuracy is obtained. Estimates of intralaboratory and interlaboratory precision are made.« less
Effects of additives on solidification of API separator sludge.
Faschan, A; Tittlebaum, M; Cartledge, F; Eaton, H
1991-08-01
API separator sludge was solidified with various combinations of binders and absorbent soil additives. The binders utilized were Type I Portland Cement, Type C Flyash, and a 1:1 combination of the two. The soil additives used were bentonite, diatomite, Fuller's earth, and two brands of chemically altered bentonites, or organoclays. The effectiveness of the solidification materials was based on their effect on the physical and leaching characteristics of the sludge.It was determined the Portland cement and combination binders provided the sludge with adequate physical and strength characteristics. It was also determined the affinity of each additive for water had an important influence on the physical characteristics of the solidified sludge. The results of the leaching procedure indicated the binders alone reduced the leachability of organic constituents from the sludge by 1/5 to 1/10. It appeared the use of the additives with the binders may have further reduced the leachability of constituents from sludge, with the incorporation of the organoclay additives further reducing leachability by up to 1/2. Also, it appeared the absorbing capacity of the additives was directly related to their ability to reduce the leachability of organic constituents from the sludge.
Magnetic biomonitoring by moss bags for industry-derived air pollution in SW Finland
NASA Astrophysics Data System (ADS)
Salo, Hanna; Mäkinen, Joni
2014-11-01
We provide the first detailed case study using Sphagnum papillosum moss bags for active magnetic monitoring of airborne industrial pollution in order to evaluate the actual role of various emission sources and the competence of current environmental protection actions relative to the air quality. The origin and spatial spreading of particulate matter (PM) based on magnetic, chemical, and SEM-EDX analyses was studied around the Industrial Park in Harjavalta, SW Finland. The data was collected during two 6-month sampling periods along 8 km transects in 2010-2011. The results support our hypothesis that the main emission source of PM is not the Cu-Ni smelter's pipe as presumed in previous chemical monitorings. We argue that the hot spot area within the severe impact pollution zone is related to slag processing and/or other unidentified industrial activity. At short distances various dust-providing sources outweigh the fly-ash load from the Cu-Ni smelter's pipe. Active magnetic monitoring by moss bags will help in planning environmental actions as well as in improvement of health conditions for industrial staff and town residents living next to the Industrial Park.
Košnář, Zdeněk; Mercl, Filip; Perná, Ivana; Tlustoš, Pavel
2016-09-01
The use of biomass fuels in incineration power plants is increasing worldwide. The produced ashes may pose a serious threat to the environment due to the presence of polycyclic aromatic hydrocarbons (PAHs), because some PAHs are potent carcinogens, mutagens and teratogens. The objective of this study was to investigate the content of total and individual PAHs in fly and bottom ash derived from incineration of phytomass and dendromass, because the data on PAH content in biomass ashes is limited. Various operating temperatures of incineration were examined and the relationship between total PAH content and unburned carbon in ashes was also considered. The analysis of PAHs was carried out in fly and bottom ash samples collected from various biomass incineration plants. PAH determination was performed using gas chromatography coupled with mass spectrometry. The correlations between the low, medium and high molecular weight PAHs and each other in ashes were conducted. The relationship between PAH content and unburned carbon, determined as a loss on ignition (L.O.I.) in biomass ashes, was performed using regression analysis. The PAH content in biomass ashes varied from 41.1±1.8 to 53,800.9±13,818.4ng/g dw. This variation may be explained by the differences in boiler operating conditions and biomass fuel composition. The correlation coefficients for PAHs in ash ranged from 0.8025 to 0.9790. The regression models were designed and the coefficients of determination varied from 0.908 to 0.980. The PAH content in ash varied widely with fuel type and the effect of operating temperature on PAH content in ash was evident. Fly ashes contained higher amounts of PAHs than bottom ashes. The low molecular weight PAHs prevailed in tested ashes. The exponential relationship between the PAH content and L.O.I. for fly ashes and the linear for bottom ashes was observed. Copyright © 2016 Elsevier B.V. All rights reserved.
NASA Astrophysics Data System (ADS)
Farrington, E. J.; Lane, C.; Hawkes, A.; Donnelly, J. P.; van Hengstum, P. J.; Woodruff, J. D.; Maio, C. V.; Grochocki, K. K.; Taylor, A. K.
2017-12-01
Paleoclimate studies in equatorial regions are essential to decipher the forcing mechanisms controlling tropical precipitation dynamics. Caribbean paleoclimate records are particularly sensitive to changes in tropical convection, as they reside on the edge of the annual migrational range of the Intertropical Convergence Zone and record perturbations to many Pacific and Atlantic climate forcings. Significant sub-regional variability exists in the modern Caribbean climate and responsible forcing mechanisms on centennial to millennial timescales are largely unresolved, as reliable paleohydrological records are geographically sparse. In this study we aim to determine regional paleoenvironmental change with a specific interest in an abrupt dry period between 3200 and 2400 14C yr BP inferred from an oxygen isotope record from the nearby Lake Miragoâne, Haiti. Chronologically synchronous results from a Barbados stalagmite indicate wet conditions, which imply contrasting sub-regional hydrological responses between the northern and southern Caribbean basin. The development of multiple proximal paleoenvironmental records allows for better assessment of sub-regional Caribbean climate dynamics and the verification of existing proxy trends. We are conducting multi-proxy analyses on a 6360 14C yr, 9-meter sediment core extracted from Baradères Bay, Haiti, including loss on ignition (LOI), bulk sediment carbon (δ13C) and nitrogen (δ15N) isotope geochemistry, n-alkane hydrogen (δD) isotope geochemistry, x-ray fluorescence (XRF), and fossil pollen counts. Preliminary LOI data reveal that between 6400 and 3000 14C yr B.P. inorganic carbon ranged from 15 to 30% and organic carbon from 8 to 20%. From 3000 14C yr B.P. to present organic content decreased (9 - 13%) and inorganic carbon content increased (28 - 30%). Preliminary pollen analyses show a decrease in Rhizophora (red mangrove) pollen abundances between 3000 and 4000 14C yr BP, possibly indicating a change in estuary salinity. Additionally, XRF data show low concentrations of titanium and zircon between 5600 and 6200 14C yr BP, which may indicate a reduction in terrestrial material input. Forthcoming δD analyses of terrestrially-derived n-alkanes should help to elucidate potential paleohydrologic mechanisms responsible for the apparent changes.
Mid Holocene climate change and impact on evolution on human settlements in northern central Europe
NASA Astrophysics Data System (ADS)
Krossa, V. R.; Kim, H.-J.; Moros, M.; Dörfler, W.; Blanz, T.; Sinninghe Damsté, J. S.; Schneider, R.
2012-04-01
The Mid Holocene climate evolution in the North Atlantic was marked by a climate optimum, followed by a transition toward colder conditions, starting at about 6 ka BP. This climate transition was accompanied by a radical change from a hunter-gatherer-fisher society toward a society based on agriculture and the domestication of animals in northern Germany and Denmark. The aim of this study is to better understand the potential impact of oceanic and terrestrial climate change on such human societies in northern Germany and Denmark. We present paleoclimatic and paleoecological reconstructions from sites surrounding the landscape where these human groups settled during the Mid Holocene. These reconstructions include a high resolution UK'37 Sea Surface Temperature (SST) record from the Skagerrak, an MBT-CBT record for estimating lake temperature from Lake Belau, Northern Germany using the calibration set of Tierney et al. (2010), and a Loss On Ignition (LOI) record representing the anoxic/oxic state from the Gotland Basin, Baltic Sea. The UK'37 record is interpreted to reflect warm season SSTs, and shows a step-like temperature drop of about 6 °C from 6.5 to 5.0 ka BP, immediately followed by a 2 °C warming at about 5.0 ka BP. The MBT-CBT lake record probably reflects mean annual temperature at our site. The record suggests mild winters and/or warm summers until 5.3 ka BP, followed by 2 °C colder conditions within 500 years. The temperature proxies suggest a positive mode in North Atlantic Oscillation (NAO) until around 5.3 ka BP, followed by conditions typical of a negative NAO mode. Furthermore, the LOI record from the Gotland Basin implies a trend from oxic to more anoxic conditions, starting at ~5.8 ka BP. More severe anoxic conditions could have led to an ecosystem shift within the Baltic Sea, resulting in a decline of copepods, codfish and seals, thus influencing mesolithic hunting activity. The climatic and ecological changes that affected the Baltic Sea might have facilitated the adaption of human societies, further developing agriculture and the domestication of animals in northern central Europe.
An Estimate of the Tidal Effects in the Dynamics of the Binary Galaxies
NASA Astrophysics Data System (ADS)
Junqueira, S.; de Freitas Pacheco, J. A.
1990-11-01
RESUMEN. Se ha estimado los efectos de marea en los pares dinamicos de galaxias elipticas. Para poder estudiar tales efectos hernos expandido el potencial gravitacional en potencias del cociente plr hasta en el orden 3 correspondientes a las fuerzas de marea. Hemos examina- do la influencia de este termino en el movimiento orbital. Se encon- tr6 el valor de M/LB = 10+7 (en unidades solares) para un ejemplo de 46 pares E-E usando Ia aproximaci6n de marea. De este resultado, no podemos concluir que existen alrededor de las galaxias halos grandes y obscuros. Hemos encontrado tambien que la suposici6n de masas puntuales es una buena aproximaci6n para el sistema fisico. Sin embargo, tal aproximaci6n sobreestima ligeramente el cociente masa-lurninosidad. ABSTRACT. In the present work we have estimated the tidal effects in the dynamics of pairs of elliptical galaxies. In order to study such effects we have expanded the gravitational potential in power of the ratio p/r up to order 3 corresponding to tidal forces. We examined the influence of this term in the orbital motion. The value of M/LB =lOi7 (in solar units) was found for a sample of 46 E-E pairs using the tidal approximation. From this result, we cannot conclude that large dark haloes exist around galaxies. We have also found that the assump- tion of point masses is a good approximation for the physical system. However, such an approximation overestimates slightly the mass-luminosity ratio. Keq wo't : GALAXIES-DYNAMICS
Assessing Carbon Storage and Sequestration of Seagrass Meadows on the Pacific Coast of Canada
NASA Astrophysics Data System (ADS)
Postlethwaite, V. R.; McGowan, A. E.; Robinson, C.; Kohfeld, K. E.; Pellatt, M. G.; Yakimishyn, J.; Chastain, S. G.
2016-12-01
Recent estimates suggest that seagrasses are highly efficient carbon sinks, storing a disproportionate amount of carbon for their relatively small area (only approximately 0.2% of the global ocean), and that they may bury carbon up to 12 times faster than terrestrial forests. Unfortunately, seagrass meadows are being lost at a rate of 0.4-2.6% yr-1, potentially releasing 0.15-1.02 Pg (billion tonnes) carbon dioxide into the atmosphere annually. Research on seagrass carbon stocks has been mainly limited to areas in the Mediterranean, Southeast Asia, and Western Australia, and specifically has been very limited in the Northeast Pacific. We aim to characterize the carbon storage and sequestration occurring in the Pacific Rim National Park Reserve and the Clayoquot Sound area, off the western coast of Vancouver Island, British Columbia (BC). Each of our sites varied in environmental characteristics representative of BC's seagrass meadows, including freshwater influence. Six cores, plus one from a "reference" site were taken from each meadow. Loss on ignition (LOI) and elemental analysis will be used to determine organic C and carbonate content. Additionally, we will use dry bulk density, 210Pb dating and seagrass density data to determine carbon accumulation rates and total meadow carbon stocks to provide a comprehensive picture of carbon storage and sequestration in BC's seagrass meadows. Carbon storage results will contribute to global estimates of seagrass carbon stocks via the Commission for Environmental Cooperation, as well as assist in marine ecosystem conservation planning and help in understanding the value of these ecosystems, especially as a means of climate change mitigation.
Low NO{sub x} burner modifications to front-fired pulverized coal boilers
DOE Office of Scientific and Technical Information (OSTI.GOV)
Broderick, R.G.; Wagner, M.
1998-07-01
Madison Gas and Electric Blount Street Station Units 8 and 9 are Babcock and Wilcox pulverized coal fired and natural gas fired boilers. These boilers were build in the late 1950's and early 1960's with each boiler rated at 425,000 lb./hr of steam producing 50 MW of electricity. The boilers are rated at 9,500 F at 1,350 psig. Each unit is equipped with one Ljungstroem air heater and two B and W EL pulverizers. These units burn subbituminous coal with higher heating value of 10,950 Btu/LB on an as-received basis. The nitrogen content is approximately 1.23% with 15% moisture. Inmore » order to comply with the new Clean Air Act Madison Gas and Electric needs to reduce NO{sub x} on these units to less than .5 LB/mmBtu. Baseline NO{sub x} emissions on these units range between .8--.9 lb./mmBtu. LOIs average approximately 8%. Madison Gas and Electric contracted with RJM Corporation to modify the existing burners to achieve this objective. These modifications consisted of adding patented circumferentially and radially staged flame stabilizers, modifying the coal pipe, and replacing the coal impeller with a circumferentially staged coal spreader. RJM Corporation utilized computational fluid dynamics modeling in order to design the equipment to modify these burners. The equipment was installed during the March 1997 outage and start-up and optimization was conducted in April 1997. Final performance results and economic data will be included in the final paper.« less
Beneficiation of limestone plant rejects for value addition.
Jena, M S; Sahu, P; Dash, P; Mohanty, J K
2013-11-15
Investigations were carried out on lime stone rejects (-1mm) generated at a lime stone washing plant in southern India. These rejects contain 12.09% CaO, 2.95% MgO, 10.73% Al2O3, 4.99% Fe2O3, 43.05% SiO2 and 24.92% LOI. Mineralogical studies including SEM-EDAX, XRD, FTIR and TGA were conducted to confirm relative distribution of minerals in the flotation feed and products. These studies revealed that feed sample consists of quartz and calcite as the major minerals with minor amounts of montmorillonite and dolomite whereas flotation concentrate dominantly consists of calcite, and tailings mostly of quartz and montmorillonite. A commercial grade sodium silicate, oleic acid and MIBC were used as depressant, collector and frother respectively in flotation studies. The effects of different operating parameters were evaluated for both conventional and column flotation. Two stage conventional cell flotation results indicate that a cleaner concentrate of 42.50% lime (CaO) content could be obtained at a yield of 15.65%. The lime (CaO) content of the concentrate was further enhanced up to 44.23% at 20.73% yield using single stage column flotation. The column flotation is more efficient in comparison to the conventional cell for treating this sample. A process flowsheet was developed to treat these rejects based on the studies carried out. This process can minimize the waste generation and the concentrate generated during this process can be directly utilized in the Indian cement industries. Copyright © 2013 Elsevier B.V. All rights reserved.
Arkhangelsk, USSR. Limited Surface Observations Climatic Summary (LISOCS). Parts A-F.
1988-01-01
MSC *225500 N 64 35 E 040 30 ELEV 43 FT ULAA PARTS A - F HOURS SUMMARIZED: SYNOPTIC HRS PERIOD 0- RECORD: HOURLY OBSERVATIONS: OCT 77 - SEP 87 SUMMARY...C/OR WicBSI TOTAL LESTI I ORIZZLL C/OR SLEET PRECIP HAZE SNOW SAND 10 ORS DRIZZLE VISION uc -02 .7 41.2 42.0 13.1 13.1 274 1,3-OS A 1.1 41.6 42.7 12.3...57.6 58.2 58.2 58.6 5-.9 58.9 59.2 59.2 59.2 54.2 GE 15LOI 17.4 45.1 49.3 58.6 63.5 66.1 67.4 68.4 68.4 68.8 69.1 69.4 69.7 p9.7 69.7 69.7 uC 1CO 19.1
The Influence of Alumina Properties on its Dissolution in Smelting Electrolyte
NASA Astrophysics Data System (ADS)
Bagshaw, A. N.; Welch, B. J.
The dissolution of a wide range of commercially produced aluminas in modified cryolite bath was studied on a laboratory scale. Most of the aluminas were products of conventional refineries and smelter dry scrubbing systems; a few were produced in laboratory and pilot calciners, enabling greater flexibility in the calcination process and the final properties. The mode of alumina feeding and the size of addition approximated to the point feeder situation. Alpha-alumina content, B.E.T. surface area and median particle size had little impact on dissolution behaviour. The volatiles content, expressed as L.O.I., the morphology of the original hydrate and the mode of calcination had the most influence. Discrete intermediate oxide phases were identified in all samples; delta-alumina content impacted most on dissolution. The flow properties of an alumina affected its overall dissolution.
LLOFX earth orbit to lunar orbit delta V estimation program user and technical documentation
NASA Technical Reports Server (NTRS)
1988-01-01
The LLOFX computer program calculates in-plane trajectories from an Earth-orbiting space station to Lunar orbit in such a way that the journey requires only two delta V burns (one to leave Earth circular orbit and one to circularize into Lunar orbit). The program requires the user to supply the Space Station altitude and Lunar orbit altitude (in km above the surface), and the desired time of flight for the transfer (in hours). It then determines and displays the trans-Lunar injection (TLI) delta V required to achieve the transfer, the Lunar orbit insertion (LOI) delta V required to circularize the orbit around the Moon, the actual time of flight, and whether the transfer orbit is elliptical or hyperbolic. Return information is also displayed. Finally, a plot of the transfer orbit is displayed.
SWANEA (Southwest Asia-Northeast Africa) A Climatological Study. Volume 3. The Near East Mountains
1991-04-01
SHIRAZ TlRA M LAT/LON: 2f 32 N 52 35 E ELEV: 4920 FT ILIHINTS JAN jFEB J MAR IAPR [MAY IJUN JJU, JAUG ISEP JOCT I NOV j DEC IAkNNJ EXT MAX 61 i75 81...M1AR APR I MAY I JUN jJUL JAUG ISEP I OCT I NOV IDE C IANN xX 5MA1 58 69 75 " ao 921 1001 98 191 j 841 67j 57’ 100 AIVG MAX .... 13 42 5 6 76 83 1 483...o t S•TATON : ESKISEHI[R T URM-’ LAT/LOI.: 39 47 N 30 34 E ELEV: 2579 FT ELEMI.-L TS !JAN FEB IMAR IAPR iHAY JUN JUL JAUG .SEP OCT NOV IDEC I NNI EXT
SELECTIVE MEDIA FOR THE ISOLATION OF PASTEURELLA PESTIS
Knisely, Ralph F.; Swaney, Lois M.; Friedlander, Harold
1964-01-01
Knisely, Ralph F. (U.S. Army Biological Laboratories, Fort Detrick, Frederick, Md.), Lois M. Swaney, and Harold Friedlander. Selective media for the isolation of Pasteurella pestis. J. Bacteriol. 88:491–496. 1964.—Several selective media are described that were successfully used to isolate virulent and avirulent strains of Pasteurella pestis from material heavily contaminated with other organisms. These media are comparatively easy to prepare, consist of readily available ingredients, and usually require no adjustment of the pH. One of the selective media described permits excellent recovery and the growth of large, easily distinguishable colonies of P. pestis in 48 hr at 26 C, and also allows the detection of fewer numbers of P. pestis organisms in soil than a previously recommended selective medium. The inhibition of other organisms frequently present in clinical specimens is described. Images PMID:14203368
A temperature reversal within the rapid Younger Dryas-Holocene warming in the North Atlantic?
NASA Astrophysics Data System (ADS)
Vincent, Jessie H.; Cwynar, Les C.
2016-12-01
The onset of the Holocene has been generally considered rapid and uninterrupted in the circum-Atlantic region. Loss-on-ignition (LOI - an index of organic carbon) profiles from 18 lateglacial-aged lakes in Nova Scotia, Canada, together with chironomid-inferred temperature reconstructions at 5 sites, demonstrate that the rapid warming from the Younger Dryas (GS-1) to the Holocene was interrupted by a cooling of 1.6-6.4 °C in summer surface lake water temperature. The resulting inflection or reversal on the rising temperature curve has also been identified at 35 sites outside Nova Scotia from terrestrial and marine settings, indicating that this cool step is a robust feature throughout the North Atlantic and is likely the result of major oceanic and atmospheric reorganization of the Holocene climate system.
Just methods in revolting times
Fine, Michelle
2016-01-01
ABSTRACT This article takes up the challenge of critical methods in “revolting times,” as we conduct qualitative research on (in)justice festering within repulsive inequality gaps, and yet surrounded by the thrill of radical social movements dotting the globe. I introduce a call for “critical bifocality,” a term coined by Lois Weis and myself, to argue for research designs that interrogate how history, structures, and lives shape, reveal, and refract the conditions we study. Borrowing from critical researchers long gone, W. E. B. Du Bois in his text The Philadelphia Negro and Marie Jahoda in her stunning case study Marienthal, I offer up a set of epistemological muddles and methodological experiments, hoping to incite a conversation about our responsibilities as critical psychologists in deeply contentious times, refusing downstream analyses and resurrecting instead what Edward Said called “lost causes.” PMID:27812314
Lunar Orbit Insertion Targeting and Associated Outbound Mission Design for Lunar Sortie Missions
NASA Technical Reports Server (NTRS)
Condon, Gerald L.
2007-01-01
This report details the Lunar Orbit Insertion (LOI) arrival targeting and associated mission design philosophy for Lunar sortie missions with up to a 7-day surface stay and with global Lunar landing site access. It also documents the assumptions, methodology, and requirements validated by TDS-04-013, Integrated Transit Nominal and Abort Characterization and Sensitivity Study. This report examines the generation of the Lunar arrival parking orbit inclination and Longitude of the Ascending Node (LAN) targets supporting surface missions with global Lunar landing site access. These targets support the Constellation Program requirement for anytime abort (early return) by providing for a minimized worst-case wedge angle [and an associated minimum plane change delta-velocity (V) cost] between the Crew Exploration Vehicle (CEV) and the Lunar Surface Access Module (LSAM) for an LSAM launch anytime during the Lunar surface stay.
Evaluation of the Epoxy/Antimony Trioxide Nanocomposites as Flame Retardant
NASA Astrophysics Data System (ADS)
Dheyaa, Balqees M.; Jassim, Widad H.; Hameed, Noor A.
2018-05-01
Antimony trioxide nanopowder was added for epoxy resin in various amount weight percentages (0, 2, 4, 6, 8, and 10) wt% to increase the combustion resistance and decrease the flammability for it. The study included three standard tests used to measure: limiting oxygen index (LOI), rate of burning (R.B), burning extent (E.B), burning time (T.B), maximum flame height (H) and residue percentage after burning in order to determine the effectiveness of the used additives to decrease the flammability of epoxy resin and increase the combustion resistance. Thermal test was done by using Lee’s disk to measure the thermal conductivity coefficient. The thermal stability and degradation kinetics of epoxy resin without reinforcement and with reinforcement by (10 wt%) were studied by using thermogravimetric analysis (TGA). The recorded results indicated that epoxy reinforced by (10 wt%) has a good effect as flame retardants for epoxy resin and active to inhibit burning and reduce the flammability.
POPSCAN: A CNES Geo-Information Study for Re-Entry Risk Assessment
NASA Astrophysics Data System (ADS)
Fuentes, N.; Tholey, N.; Battiston, S.; Montabord, M.; Studer, M.
2013-09-01
Within the framework of the FSOA, French Space Operations Act (referred to as the "Loi relative aux Opérations Spatiales" or LOS in French), including in particular the monitoring of safety requirements for people and property, one major parameter to consider is Geographic Information (GI) on population distribution, human activity, and land occupation.This article gives an overview of the set of geographic and demographic data examined for CNES control offices, outlining the advantages and limits of each one : coverage, precision, update frequency, availability, distribution, ...It focuses on the two major available global population databases: GPW-GRUMP from CIESIN of COLUMBIA University and LandScan from ORNL. The work engaged on POPSCAN integrates digital analysis about these two world population grids and also comparisons on other databases such as GLOBAL- INSIGHT, VMAP0, ESRI, DMSP-ISA, GLOBCOVER, OpenFlights, ... for urban areas, communication networks, sensitive human activities and land use.
Flame-retardant EPDM compounds containing phenanthrene to enhance radiation resistance
NASA Astrophysics Data System (ADS)
Chen, Jian; Huang, Wei; Jiang, Shu-Bin; Li, Xiao-Yan; An, You; Li, Chuang; Gao, Xiao-Ling; Chen, Hong-Bing
2017-01-01
Ethylene propylene diene monomer (EPDM) compounds with good flame-retardant and γ-ray radiation resistant properties were prepared by adding complex flame retardants and phenathrene. The resultant EPDM formulations have a long time to ignition (TTI >46 s), a low peak heat release rate (PHRR 341 kW/m2) and a high limited oxygen index (LOI >30). Effects of γ-ray radiation on the resultant flame-retardant EPDM was investigated. The formulated EPDM is a crosslinking dominated polymer under γ-ray radiation. The γ-ray radiation resistant property of EPDM was enhanced by adding phenanthrene. Elongation at break of EPDM formulated with phenanthrene could retain 91% after being irradiated to 0.3 MGy and still retains 40% elongation even after being irradiated to 0.9 MGy, which is much better the control. It is expected that the formulated flame-retardant and radiation resistant EPDM materials could meet the requirements for use in radiation environments.
Desertification treaty includes key role for scientists
NASA Astrophysics Data System (ADS)
Showstack, Randy
When Lois Barber, executive director of the non-profit group EarthAction, began efforts to press for U.S. Senate ratification of the United Nations Convention to Combat Desertification several years ago, the treaty's purpose tripped up some people, she said. They wondered whether it might be a treaty related to military personnel who had abandoned their service, de-certification of something or other, or even an overabundance of after-dinner treats. While the issue may not yet rate highly on the U.S. radar screen, U.S. Senate ratification of the Convention to Combat Desertification (CCD) on November 17, 2000 and entry into force of the treaty in the United States on February 2, 2001, could bring additional focus on desertification from the scientific community and policy-makers, according to a number of experts involved with the issue. The treaty now has been ratified by 174 countries.
Lunar lander conceptual design
NASA Technical Reports Server (NTRS)
Stecklein, J. M.; Petro, A. J.; Stump, W. R.; Adorjan, A. S.; Chambers, T. V.; Donofrio, M.; Hirasaki, J. K.; Morris, O. G.; Nudd, G.; Rawlings, R. P.
1992-01-01
This paper is a first look at the problems of building a lunar lander to support a small lunar surface base. A series of trade studies was performed to define the lander. The initial trades concerned choosing number of stages, payload mass, parking orbit altitude, and propellant type. Other important trades and issues included plane change capability, propellant loading and maintenance location, and reusability considerations. Given a rough baseline, the systems were then reviewed. A conceptual design was then produced. The process was carried through only one iteration. Many more iterations are needed. A transportation system using reusable, aerobraked orbital transfer vehicles (OTV's) is assumed. These OTV's are assumed to be based and maintained at a low Earth orbit (LEO) space station, optimized for transportation functions. Single- and two-stage OTV stacks are considered. The OTV's make the translunar injection (TLI), lunar orbit insertion (LOI), and trans-Earth injection (TEI) burns, as well as midcourse and perigee raise maneuvers.
1976-03-01
bito M« MO7 J " u.UO7« O.OUOJ 00 to 1*5 l*e lt7 l*b i’*9 151 152 153 13...l/J " 1/4 If«, l/i il-t ~ Ha- ifa 17/ 1/9 !/<• low ’ioi"- loc lo3 lot »3.4:5 33.Oj 33. 3u 33.ft 33.-»3 34.Ö-4 3~t.43...34 Ü.O301 0.332* 0.0296 0.2536 10 1 lOc loi Hi 0.2973 0.2913 0.25*> 0.2972 1U> loo 1.227? 1.^120 "l*«9da 1.2 1*2 ~l.*.3o2" 1.2137
Hazard Management with DOORS: Rail Infrastructure Projects
NASA Astrophysics Data System (ADS)
Hughes, Dave; Saeed, Amer
LOI is a major rail infrastructure project that will contribute to a modernised transport system in time for the 2012 Olympic Games. A review of the procedures and tool infrastructure was conducted in early 2006, coinciding with a planned move to main works. A hazard log support tool was needed to provide: an automatic audit trial, version control and support collaborative working. A DOORS based Hazard Log (DHL) was selected as the Tool Strategy. A systematic approach was followed for the development of DHL, after a series of tests and acceptance gateways, DHL was handed over to the project in autumn 2006. The first few months were used for operational trials and he Hazard Management rocedure was modified to be a hybrid approach that used the strengths of DHL and Excel. The user experience in the deployment of DHL is summarised and directions for future improvement identified.
Smolka-Danielowska, Danuta
2010-11-01
The subject of the study covered volatile ashes created during hard coal burning process in ash furnaces, in power plants operating in the Upper Silesian Industrial Region, Southern Poland. Coal-fired power plants are furnished with dust extracting devices, electro precipitators, with 99-99.6% combustion gas extracting efficiency. Activity concentrations ofTh-232, Ra-226, K-40, Ac-228, U-235 and U-238 were measured with gamma-ray spectrometer. Concentrations of selected rare soil elements (La, Ce, Nd, Sm, Y, Gd, Th, U) were analysed by means of instrumental neutron activation analysis (INAA). Mineral phases of individual ash particles were identified with the use of scanning electron microscope equipped with EDS attachment. Laser granulometric analyses were executed with the use of Analyssette analyser. The activity of the investigated fly-ash samples is several times higher than that of the bituminous coal samples; in the coal, the activities are: 226Ra - 85.4 Bq kg(-1), 40 K-689 Bq kg(-1), 232Th - 100.8 Bq kg(-1), 235U-13.5 Bq kg(-1), 238U-50 Bq kg(-1) and 228Ac - 82.4 Bq kg(-1).
XAFS studies of nickel and sulfur speciation in residual oil fly-ash particulate matters (ROFA PM).
Pattanaik, Sidhartha; Huggins, Frank E; Huffman, Gerald P; Linak, William P; Miller, C Andrew
2007-02-15
XAFS spectroscopy has been employed to evaluate the effect of fuel compositions and combustion conditions on the amount, form, and distribution of sulfur and nickel in size-fractionated ROFA PM. Analysis of S K-edge XANES establish that sulfate is abundant in all PM. However, depending upon the combustion conditions, lesser amounts of thiophenic sulfur, metal sulfide, and elemental sulfur may also be observed. Least-squares fitting of Ni K-edge XANES reveals that most of the nickel in PM is present as bioavailable NiSO4.nH2O. The insoluble Ni mainly exists as a minor species, as nickel ferrite in PM2.5 (PM < 2.5 microm) and nickel sulfide, Ni(x)SY(y) in PM2.5+ (PM > 2.5 microm). The Ni K-edge XANES results are in agreement with the EXAFS data. Such detailed speciation of Ni and S in PM is needed for determining their mobility, bioavailability, and reactivity, and hence, their role in PM toxicity. This information is also important for understanding the mechanism of PM formation, developing effective remediation measures, and providing criteria for identification of potential emission sources. Transition metals complexing with sulfur is ubiquitous in nature. Therefore, this information on metal sulfur complex can be critical to a large body of environmental literature.
NASA Astrophysics Data System (ADS)
Behera, Ajit; Behera, Asit; Mishra, S. C.; Pani, S.; Parida, P.
2015-02-01
Fly-ash premixed with quartz and illmenite powder in different weight proportions are thermal sprayed on mild steel and copper substrates at various input power levels of the plasma torch ranging from 11 kW to 21 kW DC. The erosion test has done using Air Jet erosion test Reg (As per ASTM G76) with silica erodent typically 150-250 pm in size. Multiple tests were performed at increasing the time duration from 60 sec to 180 sec with increasing pressure (from 1 bar to 2.5 bar) and angle (60° & 90°). This study reveals that the impact velocity and impact angle are two most significant parameters among various factors influencing the wear rate of these coatings. The mechanisms and microstructural changes that arise during erosion wear are studied by using SEM. It is found that, when erodent are impacting the fresh un-eroded surface, material removal occurs by the continuous evolution of craters on the surface. Upper layer splats are removed out after 60 sec and second layer splat erosion starts. Based on these observations Physical models are developed. Some graphs plotted between mass loss-rate versus time period/impact Pressure/impact Angle gives good correlation with surface features observed.
Koo, Bon-Min; Kim, Jang-Ho Jay; Kim, Tae-Kyun; Kim, Byung-Yun
2015-01-01
In this study, the amount of cement used in a concrete mix is minimized to reduce the toxic effects on users by adjusting the concrete mixture contents. The reduction of cement is achieved by using various admixtures (ground granulated blast-furnace slag, flyash, ordinary Portland cement, and activated Hwangtoh powder). To apply the mix to construction, material property tests such as compressive strength, slump, and pH are performed. Preliminary experimental results showed that the Hwangtoh concrete could be used as a healthy construction material. Also, the health issues and effects of Hwangtoh mortar are quantitatively evaluated through an animal clinical test. Mice are placed in Hwangtoh mortar and cement mortar cages to record their activity. For the test, five cages are made with Hwangtoh and ordinary Portland cement mortar floors, using Hwangtoh powder replacement ratios of 20%, 40%, 60%, and 80% of the normal cement mortar mixing ratio, and two cages are made with Hwangtoh mortar living quarters. The activity parameter measurements included weight, food intake, water intake, residential space selection, breeding activity, and aggression. The study results can be used to evaluate the benefits of using Hwangtoh as a cement replacing admixture for lifestyle, health and sustainability. PMID:28793563
Jedidi, Ilyes; Saïdi, Sami; Khemakhem, Sabeur; Larbot, André; Elloumi-Ammar, Najwa; Fourati, Amine; Charfi, Aboulhassan; Salah, Abdelhamid Ben; Amar, Raja Ben
2009-12-15
This work aims to develop a new mineral porous tubular membrane based on mineral coal fly ash. Finely ground mineral coal powder was calcinated at 700 degrees C for about 3 h. The elaboration of the mesoporous layer was performed by the slip-casting method using a suspension made of the mixture of fly-ash powder, water and polyvinyl alcohol (PVA). The obtained membrane was submitted to a thermal treatment which consists in drying at room temperature for 24 h then a sintering at 800 degrees C. SEM photographs indicated that the membrane surface was homogeneous and did not present any macrodefects (cracks, etc...). The average pore diameter of the active layer was 0.25 microm and the thickness was around 20 microm. The membrane permeability was 475 l/h m(2) bar. This membrane was applied to the treatment of the dying effluents generated by the washing baths in the textile industry. The performances in term of permeate flux and efficiency were determined and compared to those obtained using a commercial alumina microfiltration membrane. Almost the same stabilised permeate flux was obtained (about 100 l h(-1)m(-2)). The quality of permeate was almost the same with the two membranes: the COD and color removal was 75% and 90% respectively.
Koo, Bon-Min; Kim, Jang-Ho Jay; Kim, Tae-Kyun; Kim, Byung-Yun
2015-09-17
In this study, the amount of cement used in a concrete mix is minimized to reduce the toxic effects on users by adjusting the concrete mixture contents. The reduction of cement is achieved by using various admixtures (ground granulated blast-furnace slag, flyash, ordinary Portland cement, and activated Hwangtoh powder). To apply the mix to construction, material property tests such as compressive strength, slump, and pH are performed. Preliminary experimental results showed that the Hwangtoh concrete could be used as a healthy construction material. Also, the health issues and effects of Hwangtoh mortar are quantitatively evaluated through an animal clinical test. Mice are placed in Hwangtoh mortar and cement mortar cages to record their activity. For the test, five cages are made with Hwangtoh and ordinary Portland cement mortar floors, using Hwangtoh powder replacement ratios of 20%, 40%, 60%, and 80% of the normal cement mortar mixing ratio, and two cages are made with Hwangtoh mortar living quarters. The activity parameter measurements included weight, food intake, water intake, residential space selection, breeding activity, and aggression. The study results can be used to evaluate the benefits of using Hwangtoh as a cement replacing admixture for lifestyle, health and sustainability.
Weathering process in Sør Rondane Mountains, East Antarctica
NASA Astrophysics Data System (ADS)
Kanamaru, T.; Suganuma, Y.; Oiwane, H.; Miura, M.; Okuno, J.; Hayakawa, H.
2016-12-01
Weathering process under the hyper-arid and hypothermal environment is a key to understand the geomorphogic process and landscape evolution in Antarctica and on Mars. A nunber of studies have focused on weathering process of basaltic rocks in Antarctica, however, the nature of the weathering process of plutonic type rock, a common rock type on the Earth, have been less focused and remain unclear. Here, we report the physical/chemical weathering process of the granitic rocks obtained from Dronning Maud Land in East Antarctica based on a multiplicity of petrological approaches. Loss on Ignition (LOI) and major element composition of the crust and core of the rock samples indicate that chemical weathering process in this area seems to be very limited. The microscopic observations and laser-Raman micro spectroscopy for thin sections from the crust and core indicate that goethite grains are formed mainly in the vein around the crust, which is consistent with the higher Fe3+/Fe2+ contrast from the core to crust. A negative correlation between the rock hardness and color strength index (CSI) values also indicate that crust of rock samples tend to less hard than core due to cracking of the rock samples and following goethite formation. On the other hand, EPMA analysis indicates that original Fe-Ti oxide grains in the core of rock samples are damaged by weathering, and altered to hematite, and to non-stoichiometric Fe-Ti compound associated with ilmenite grans in case of the higher relative height samples. These reveal that the weathering process of the plutonic rocks under the hyper-cold and hypothermal environment are mainly controlled by oxidation, including iron hydroxide formation in the veins formed by mechanical distraction, and Fe-Ti oxide alteration in rock interior.
NASA Astrophysics Data System (ADS)
Surour, Adel A.; El-Nisr, Said A.; Bakhsh, Rami A.
2016-03-01
Miocene rhyolites (19.2 ± 0.9 Ma) at the Jabal Shama in western Saudi Arabia represent an example of rift-related silicic volcanism that took place during the formation of the Red Sea. They mostly consist of tuffaceous varieties with distinct flow banding, and pea-sized spherulites, obsidian and perlitized rhyolite tuffs. Although they have the geochemical signature of A2-type rhyolites, these silicic rocks are not typically alkaline but alkali-calcic to calc-alkaline. They developed in a within-plate regime and possibly derived from a recycled mafic subducted slab in depleted sub-continental mantle beneath the western Arabian plate. The Jabal Shama rhyolites are younger in age than their Miocene counterparts in Yemen and Ethiopia. The Jabal Shama spherulites consist of hydrous alkali feldspar-silica radial intergrowths with an occasional brown glass nucleus. Carbonate- and glass-free spherulites give up to 4.45 wt% L.O.I. The hydrous nature of these silicates and the absence of magnetite in the spherulites is a strong indication of oxidizing conditions. The spherulites contain hydrous feldspars with up to ∼6 wt% H2O, and they develop by diffusion and devitrification of glass in the rhyolite tuff at ∼800 °C. Owing to higher undercooling due to supersaturation, the radial hydrous phases within spherulites might grow faster and led to coagulation. The polygonal contacts between spherulites and the ∼120° dihedral angle suggest solid-state modification and recrystallization as the process of devitrification proceeds as low as ∼300 °C. The sum of FeO + MgO is positively correlated with total alkalies along with magnetite oxidation in the matrix to Fe-oxyhydroxides, and to the incorporation of OH- into silicates within the spehrulites themselves. Structural H2O in glass of the Jabal Shama perlite (obsidian) is considerable (∼9-12 wt%) with 3.72-5.6 wt% L.O.I. of the whole-rock. The presence of deleterious silica impurities would lower the ore grade due to poor expansion. Zeolitization of the rhyolite tuff was limited or incomplete in comparison with that of Pliocene-Pleistocene rift-related mafic volcanics in the western Arabian plate.
Mobility of gold during metamorphism of the Dalradian in Scotland
NASA Astrophysics Data System (ADS)
Pitcairn, I. K.; Skelton, A. D. L.; Wohlgemuth-Ueberwasser, C. C.
2015-09-01
Mobility of Au and related metals during metamorphism has been suggested to be the source of metals enriched in orogenic Au deposits. This study investigates the mobility of Au, As, and Sb during metamorphism of the Dalradian metasedimentary rocks of Scotland. The metamorphic processes in the Dalradian of Scotland are extremely well studied, and the terrane is an ideal area to investigate mobility of these metals. Our results show that of the 25 major and trace elements analysed, only Au, As, Sb, S and volatile contents as shown by loss on ignition (LOI) values show systematic variation with the metamorphic grade of the samples. Average Au concentrations decrease from 1.1 ± 0.55 ppb and 0.72 ± 0.34 ppb in chlorite and biotite zone rocks down to 0.4 ± 0.22 ppb and 0.34 ± 0.13 ppb in kyanite and sillimanite zone rocks. Average As concentrations decrease from 4.8 ppm (range 0.5 to 17.8 ppm) and 1.96 ± 1.9 ppm in chlorite and biotite zone rocks down to 0.24 ± 0.15 ppm and 0.2 ± 0.12 ppm in kyanite and sillimanite zone rocks. Average Sb concentrations decrease from 0.18 ± 0.15 ppm and 0.11 ± 0.10 ppm in chlorite and biotite zone rocks down to 0.04 ± 0.02 ppm in both kyanite and sillimanite zone rocks. Sulphur and LOI concentrations also show significant decreases. Mass balance calculations indicate that compared to chlorite and biotite zone samples, sillimanite zone samples have an average mass loss of 62 ± 14%, 94 ± 4% and 74 ± 14% for Au, As, and Sb respectively. Every 1 km3 of chlorite-biotite zone mixed psammitic-pelitic protolith rock that is metamorphosed to sillimanite zone conditions would release 1.5 t Au, 8613 t As, 270 t Sb, and 1.02 Mt S. The mobility of these elements is strongly controlled by the paragenesis of sulphide minerals. Pyrite, sphalerite, galena and cobaltite (as well as gersdorffite) decrease in abundance with increasing metamorphic grade in the Dalradian metasedimentary rocks. A critical aspect of the sulphide paragenesis is the transition of pyrite to pyrrhotite. This transition is complete by mid greenschist facies in the Loch Lomond samples but is more gradual at Glen Esk occurring between biotite and sillimanite zones. The Au, As, and Sb content of the sulphide assemblage also decreases with increasing metamorphic grade, and we suggest that this is a controlling factor on the mobility of these metals from the Dalradian metasedimentary rocks during metamorphism. Chlorite may be an important host mineral for As in the greenschist facies rocks. Breakdown of chlorite indirectly drives the mobility of Au, As, and Sb, as this produces the bulk of metamorphic fluid that drives transition between pyrite and pyrrhotite. We suggest that there is potential for significant undiscovered mineralisation in the Central and SW Highlands of Scotland. However, as the total mass of gold mobilised is lower than observed in other metasedimentary terranes such as the Otago and Alpine Schist's, New Zealand, very efficient fluid focussing and trapping mechanisms would be required to form large deposits in the Dalradian of Scotland.
NASA Astrophysics Data System (ADS)
Koutsovitis, Petros
2017-04-01
In Central Greece, the East Thessaly region encompasses ophiolitic and metaophiolitic formations emplaced onto Mesozoic platform series rocks. Metaophiolitic thrust sheets are characterized either by the predominance of serpentinites or metabasites. Serpentinites have been distinguished into three groups, representing distinct metamorphic degrees. Group-1 serpentinites (East Othris region) are characterized by the progressive transformation of lizardite to antigorite, estimated to have been formed under greenschist facies conditions (˜320-340 ˚ C, P≈6-8 kbar) [1]. Group-2 serpentinites (NE Othris and Agia-Agiokampos region) are marked by the further prevalence of antigorite over lizardite, suggesting upper-greenschist to low-blueschist facies metamorphism (˜340-370 ˚ C, P≈9-11 kbar) [1]. Group-3 serpentinites (Agia-Agiokampos region) are characterized by the predominance of antigorite and Cr-magnetite, as well as by their relatively low LOI (10.9-12.6 wt.%), corresponding to blueschist facies metamorphism (˜360-400 ˚ C, P≈12 kbar) [1]. These metamorphic conditions are highly comparable with the P-T estimates from the Easternmost Thessaly metabasic rocks, strongly indicating that the entire metaophiolitic formation (excluding East Othris) underwent blueschist facies metamorphism. Serpentinites from East Thessaly were formed from serpentinization of highly depleted harzburgitic protoliths under extensive partial melting processes (>15%), pointing to a hydrous subduction-related environment. Group-1 serpentinites exhibit higher Mg/Si ratio values and LOI compared to serpentinite Groups-2 and -3. Differences in the trace element behavior amongst the three serpentinite groups are also consistent with increasing metamorphic conditions (e.g. Pb, La enrichments, Ti, Y, Yb depletions) [1]. The East Thessaly serpentinites reflect highly oxidizing conditions (-0.4< FMQ<1.2) [1]. These serpentinites appear to have also been subjected to deserpentinization retrograde metamorphic processes (P<8 kbar and T<350 ˚ C) [1]. Retrograde metamorphism also resulted in the occurrence of late-stage rodingitization and derodingitization processes upon the rodingite intrusions hosted within the serpentinites. Late-stage derodingitization processes (T=250-300 oC) account for the formation of metarodingites (vesuvianite and/or chlorite bearing). Chlorite-serpentinite schists represent a reaction zone between the serpentinites and the hosted metarodingites [1]. Exhumation of the high-pressure serpentinite- and metabasic-bearing metaophiolitic occurrences may have occurred from either one or even from both of the bilateral oceanic basins (Pindos and Vardar) that coexisted besides the elongated Pelagonian zone. The Middle-Late Jurassic Pindos oceanic SSZ model appears to successfully interpret not only the geochemical and structural data recorded in the western Hellenic-Dinaric ophiolitic complexes, but additionally seems to explain the formation and emplacement for many of the East Thessaly metaophiolite occurrences. In this context, the exhumed metaophiolites represent parts either of a serpentinized subduction channel or of the serpentinized wedge, located on the hanging wall side close to the slab in the forearc system of the Pindos Ocean. The Hellenic-Dinaric ophiolitic units, as well as the metaophiolitic occurrences, were likely remobilized during thrusting of the flyschic nappe at the main Alpine orogenetic phase of the Upper Cretaceous-Paleogene period. References. [1] Koutsovitis 2016: Lithos, Special Issue, in Press. DOI: 10.1016/j.lithos.2016.11.008
Viguri, J; Verde, J; Irabien, A
2002-07-01
Samples of intertidal surface sediments (0-2 cm) were collected in 17 stations of the Santander Bay, Cantabric Sea, Northern Spain. The concentrations of polycyclic aromatic hydrocarbons (PAHs), 16, were analysed by HPLC and MS detection. Surface sediments show a good linear correlation among the parameters of the experimental organic matter evaluation, where total carbon (TC) and loss on ignition (LOI) are approximately 2.5 and 5 times total organic carbon (TOC). A wide range of TOC from 0.08% to 4.1%, and a broad distribution of the sum of sigma16PAHs, from 0.02 to 344.6 microg/g d.w., which can be correlated by an exponential equation to the TOC, has been identified. A qualitative relationship may be established between the industrial input along the rivers and the concentration of sigma6PAHs in the sediments of the estuaries: Boo estuary (8404-4631 microg/g OC), Solia-San Salvador estuaries (305-113 microg/g OC) and Cubas estuary (31-32 microg/g OC). This work shows a dramatic change in the spatial distribution in the concentration of PAHs of intertidal surface sediments. The left edge of the Bay has the main traffic around the city and the major source of PAHs is from combustion processes and estuarine inputs, leading to medium values of PAHs in the sediments; the right edge of the Bay has much lesser anthropogenic activities leading to lower values of PAHs in sediments. The distribution of individual PAHs in sediments varies widely depending on their structure and molecular weight; the 4-6 ring aromatics predominate in polluted sediments due to their higher persistence. The isomer ratio does not allow any clear identification of the PAHs origin. Environmental evaluation according to Dutch guidelines and consensus sediment quality guidelines based on ecotoxicological data leads to the same conclusion, sediments in the Santander Bay show a very different environmental quality depending on the spatial position from heavily polluted/medium effects to non-polluted/below threshold effects. These results indicate that local sources of PAHs, especially estuary discharges, lead to very different qualities of sediments in coastal zones, where traffic and industrial activities take place.
CO2 sequestration by carbonation of steelmaking slags in an autoclave reactor.
Chang, E-E; Pan, Shu-Yuan; Chen, Yi-Hung; Chu, Hsiao-Wen; Wang, Chu-Fang; Chiang, Pen-Chi
2011-11-15
Carbon dioxide (CO(2)) sequestration experiments using the accelerated carbonation of three types of steelmaking slags, i.e., ultra-fine (UF) slag, fly-ash (FA) slag, and blended hydraulic slag cement (BHC), were performed in an autoclave reactor. The effects of reaction time, liquid-to-solid ratio (L/S), temperature, CO(2) pressure, and initial pH on CO(2) sequestration were evaluated. Two different CO(2) pressures were chosen: the normal condition (700 psig) and the supercritical condition (1300 psig). The carbonation conversion was determined quantitatively by using thermo-gravimetric analysis (TGA). The major factors that affected the conversion were reaction time (5 min to 12h) and temperature (40-160°C). The BHC was found to have the highest carbonation conversion of approximately 68%, corresponding to a capacity of 0.283 kg CO(2)/kg BHC, in 12h at 700 psig and 160°C. In addition, the carbonation products were confirmed to be mainly in CaCO(3), which was determined by using scanning electron microscopy (SEM) and X-ray powder diffraction (XRD) to analyze samples before and after carbonation. Furthermore, reaction kinetics were expressed with a surface coverage model, and the carbon footprint of the developed technology in this investigation was calculated by a life cycle assessment (LCA). Copyright © 2011 Elsevier B.V. All rights reserved.
[Pathologic skin changes in workers at electric and thermoelectric power plants].
Kieć-Swierczyńska, M; Woźniak, H
1988-01-01
Dermatological examination was performed and epidermal tests using a routine set of allergens and metals (Cr, Co, Ni, Al, Cu, Ag, Zn, Hg, Fe) on 112 workers of power plants and thermal-electric power stations working at the stands characterized by a heavy dustiness (electro-filters operation, ash removal, deslagging, carburizing) and at the stands where dustiness was not so heavy but instead exposure to machine oils and greases (retors' operators, electromechanics, assemblers and welders) was remarkable. It was found that occupational exposure to chemicals resulted in skin inflammation in 7.1% of the examined persons. Machine oils and greases induced skin inflammation in 2.7% and occupational acne in 5.3% of workers. It was also observed that chromium compounds were the primary allergen in workers exposed to dusts (13.4% of sensitized persons) and in workers exposed to industrial greases and oils (8.0% of sensitized persons). Allergy to cobalt compounds prevailed among persons exposed to smears and oils. Single positive results of epidermal tests with the use of copper and silver were obtained. Moreover, data concerning the microelements content in fly-ashes are presented. Information on the frequency of the incidence of occupational skin diseases, sickness absenteeism due to dermatoses and on personal safety equipment which should be used by the workers of power industry plants are provided.
Molina, L; Cabes, M; Díaz-Ferrero, J; Coll, M; Martí, R; Broto-Puig, F; Comellas, L; Rodríguez-Larena, M C
2000-01-01
The analysis of planar (non-ortho) polychlorinated biphenyls (PCB) by HRGC-ECD or HRGC-HRMS requires a fractionation step to avoid the interferences of the bulk of PCB, usually in much higher concentration than the planar ones. In this paper, a new method, based on the fractionation of PCB on SPE commercial tubes pre-packed with Carbopack B, has been developed. After the extract has been applied on the stationary phase, the bulk of PCD are eluted with 15 ml of hexane (fraction I), mono-ortho PCB with 20 ml of hexane/toluene 99:1 (fraction II) and planar PCB with 20 ml of toluene (fraction III) in a station under vacuum. The method has been validated: accuracy (expressed as recovery in %) is >70% and precision (expressed as % RSD) is <20% considering changes of day, analyst and batch of tubes. The method is linear in the range studied. Other advantages are that the method is simple, rapid and it can be easily automated. The application of this separation to the determination of planar PCB in fly-ash extracts from an intercalibration exercise and to sewage sludge, sediment and soil samples has been successful. In addition, this method removes hydrocarbons from the planar PCB fraction and allows its concentration to very small volumes.
Formation of PCDD/Fs from Oxidation of 2-Monochlorophenol over an Fe2O3/Silica Surface
Nganai, Shadrack; Lomnicki, Slawo; Dellinger, Barry
2012-01-01
The role of iron in surface-mediated formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from 2-chlorophenol (2-MCP) was investigated over the temperature range of 200 to 550°C under oxidative conditions. In order to compare and contrast with previous work on copper and ferric oxide-mediated pyrolysis of 2-MCP, identical reaction conditions were maintained (50 ppm 2-MCP, model fly-ash particles containing 5% Fe2O3 on silica). Observed products included dibenzo-p-dioxin (DD), 1-monochlorodibenzo-p-dioxin (1-MCDD), dibenzofuran (DF), 4,6-dichlorodibenzofuran (4,6-DCDF), 2,4– and 2,6-dichlorophenol, 2,4,6-trichlorophenol, quinone, catechol, chloro-o-quinone, chlorocatechol and polychlorinated benzenes. Yields of DD and 1-MCDD were 2 and 5 times higher than under pyolysis conditions, respectively. Although 4,6-DCDF was the major PCDD/F product formed with a yield that was 2.5x greater than under pyrolysis, the yield of non-chlorinated DF, which was the dominant PCDD/F product under pyrolysis, decreased by a factor of 3. Furthermore, the ~2x higher yield of PCDDs under oxidative conditions resulted in a PCDD to PCDF ratio of 0.75 compared to a relatively low ratio of 0.39 previously observed under pyrolytic conditions. PMID:22525510
DOE Office of Scientific and Technical Information (OSTI.GOV)
Besser, J.; Giesy, J.; Brown, R.
1995-12-31
Bioaccumulation of Se by fish from Pigeon River and Pigeon Lake, Michigan, which receive inputs of Se from a coal fly-ash disposal facility, was studied to assess potential hazards of Se toxicity to fish and wildlife. Se concentrations in fish from sites receiving Se inputs from fly ash disposal ponds were significantly greater than concentrations in fish from upstream sites, which were near normal background concentrations. Se bioaccumulation differed substantially among fish species, especially in the most contaminated site, where whole-body Se concentrations for the five species analyzed ranged from 1.4 to 3.8 {micro}g/g (wet wt.). The top predator inmore » the community, northern pike (Esox lucius), had Se concentrations less than those in likely prey species. Among lower-order consumers, Se concentrations were greater in limnetic species (spottail shiner, Notropis hudsonius, and yellow perch, Perca flavescens), than in benthic species (white sucker, Catostomus commersoni, and rock bass, Ambloplites rupestris). Se concentrations in tissues of fish from the lower Pigeon River and Pigeon Lake approached, but did not exceed lowest observable effect concentrations (LOAECs) for Se in tissues of sensitive fish species. However, Se concentrations in several fish species exceeded LOAECs for dietary Se exposure of sensitive species of birds and mammals, suggesting that consumption of fish in these areas may pose a hazard to piscivorous wildlife.« less
AFOSR Technical Report Summaries
1989-06-01
u w Zx~ Z ~ 54 3 3D m t 0 - -U25CD _t TD M 10 -. ’S. 0 .&UU 0 Z 0 Ix0-0 <wU-0 <- Z L .OUO -0U-0 M 1X C -L-VNC M M N LN L - N U M 10ENC Z C’ (14 -’V...L r4 0 1- m - li N uj 1) 0 .0 0 -T L 0 M 0 C L 00 > 0 tD u Co 0 0 C4 (A 13 X >, 0 P- Q u n 07 2) Ln ad 4) in Ix L 0 W Z VI - (Z -- I- . Z L 10 L 4...0 a.- Cm C a C U 0 (A 0. a) 0 - CA 0 L1 - -a 0 M c L C -~ >0 fa LOI .- ) .fl m , Mo tt cm C aE z -c4 -~ tD L.u - 0 0L 0 -f WD- 0uM 00 L C0 1
Removal of unburned carbon from coal fly ash using a pneumatic triboelectrostatic separator.
Kim, J K; Cho, H C; Kim, S C
2001-01-01
A pneumatic triboelectrostatic beneficiation system of fly ash was studied using a continuous, bench-scale electroseparator composed of two vertical electrode plates and an ejector-tribocharger. Tests were conducted to evaluate the charge density and the separation efficiency at various operating conditions. It was found that the higher charge densities were obtained at (1) the air flow rate of 1.75 m3/min. (2) the feed rate of less than 50 kg/h. and (3) the relative humidity of less than 30% with use of a stainless ejector tribocharger. With these optimum conditions, the clean ash of less than LOI 3% was recovered with a yield over 75% when operated at the diffuser slit gap of 4mm, the diffuser outlet velocity of 16.1-18.6 m/s, and the distance of 15 cm between diffuser slit and splitter. The optimum feed rate was found to be 740 kg/h per m2 of electrode surface area, which can be used as a scale-up factor of electroseparator.
The Air Force National Guard and the Air Force Reserve: Points to Ponder for the Future.
1987-05-01
34 thet i t tmAt- imv . ’ .i I riq iht I 1 u 1 Ii how thr, wi 1 1 mobJ I i -e, their peoi’onoiel -nAri % In ’IA ŘL, n F:,,n,- t wh:on recaI ld od Th I...iabi I I tv tc’r’ tt-I,> I ’.IflI :I’ tiL iiki fl iI’r4t qI pat t tIE? #-it E’ry i tt It - z dir -o o Cnz. numhvllt (- tt tf te ir tpca aA lab n >9...i lab c t the 1--’ rt Ior I-~ ci- tui dL-temine _-- cori’-ensue5L amonq ’(I ois : ’r’ loi onI o~ P,- t o m j r1 t v I.)+ t hc. mernhfl_- e r c -f the
NASA Technical Reports Server (NTRS)
Jayarajan, A.; Johnson, G. A.; Korver, G. L.; Anderson, R. A.
1983-01-01
Five chemically different resin systems with improved fire resistance properties were studied for a possible screenprinting ink application. Fire resistance is hereby defined as the cured ink possessing improvements in flammability, smoke emission, and thermal stability. The developed ink is for application to polyvinyl fluoride film. Only clear inks without pigments were considered. Five formulations were evaluated compared with KC4900 clear acrylic ink, which was used as a baseline. The tests used in the screening evaluation included viscosity, smoke and toxic gas emission, limiting oxygen index (LOI), and polyvinyl fluoride film (PVF) printability. A chlorofluorocarbon resin (FPC461) was selected for optimization studies. The parameters for optimization included screenprinting process performance, quality of coating, and flammability of screenprinted 0.051-mm (0.002-in.) white Tedlar. The quality of the screenprinted coating on Tedlar is dependent on viscosity, curing time, adhesion to polyvinyl fluoride film, drying time (both inscreen and as an applied film), and silk screen mesh material and porosity.
NASA Technical Reports Server (NTRS)
Nayagam, Vedha; Dietrich, Daniel L.; Ferkul, Paul V.; Hicks, Michael C.; Williams, Forman A.
2012-01-01
Motivated by the need to understand the flammability limits of condensed-phase fuels in microgravity, isolated single droplet combustion experiments were carried out in the Combustion Integrated Rack Facility onboard the International Space Station. Experimental observations of methanol droplet combustion and extinction in oxygen/carbon-dioxide/nitrogen mixtures at 0.7 and 1 atmospheric pressure in quiescent microgravity environment are reported for initial droplet diameters varying between 2 mm to 4 mm in this study.The ambient oxygen concentration was systematically lowered from test to test so as to approach the limiting oxygen index (LOI) at fixed ambient pressure. At one atmosphere pressure, ignition and some burning were observed for an oxygen concentration of 13% with the rest being nitrogen. In addition, measured droplet burning rates, flame stand-off ratios, and extinction diameters are presented for varying concentrations of oxygen and diluents. Simplified theoretical models are presented to explain the observed variations in extinction diameter and flame stand-off ratios.
Myotubularin-related protein 7 inhibits insulin signaling in colorectal cancer
Gutting, Tobias; Friedrich, Teresa; Gaiser, Timo; Magdeburg, Julia; Kienle, Peter; Ruh, Hermelindis; Hopf, Carsten; Behrens, Hans-Michael; Röcken, Christoph; Hanoch, Tamar; Seger, Rony; Ebert, Matthias P.A.; Burgermeister, Elke
2016-01-01
Phosphoinositide (PIP) phosphatases such as myotubularins (MTMs) inhibit growth factor receptor signaling. However, the function of myotubularin-related protein 7 (MTMR7) in cancer is unknown. We show that MTMR7 protein was down-regulated with increasing tumor grade (G), size (T) and stage (UICC) in patients with colorectal cancer (CRC) (n=1786). The presence of MTMR7 in the stroma correlated with poor prognosis, whereas MTMR7 expression in the tumor was not predictive for patients' survival. Insulin reduced MTMR7 protein levels in human CRC cell lines, and CRC patients with type 2 diabetes mellitus (T2DM) or loss of imprinting (LOI) of insulin-like growth factor 2 (IGF2) had an increased risk for MTMR7 loss. Mechanistically, MTMR7 lowered PIPs and inhibited insulin-mediated AKT-ERK1/2 signaling and proliferation in human CRC cell lines. MTMR7 provides a novel link between growth factor signaling and cancer, and may thus constitute a potential marker or drug target for human CRC. PMID:27409167