Modeling Stochastic Energy and Water Consumption to Manage Residential Water Uses

NASA Astrophysics Data System (ADS)

Abdallah, A. M.; Rosenberg, D. E.; Water; Energy Conservation

2011-12-01

Water energy linkages have received growing attention from the water and energy utilities as utilities recognize that collaborative efforts can implement more effective conservation and efficiency improvement programs at lower cost with less effort. To date, limited energy-water household data has allowed only deterministic analysis for average, representative households and required coarse assumptions - like the water heater (the primary energy use in a home apart from heating and cooling) be a single end use. Here, we use recent available disaggregated hot and cold water household end-use data to estimate water and energy consumption for toilet, shower, faucet, dishwasher, laundry machine, leaks, and other household uses and savings from appliance retrofits. The disaggregated hot water and bulk water end-use data was previously collected by the USEPA for 96 single family households in Seattle WA and Oakland CA, and Tampa FL between the period from 2000 and 2003 for two weeks before and four weeks after each household was retrofitted with water efficient appliances. Using the disaggregated data, we developed a stochastic model that represents factors that influence water use for each appliance: behavioral (use frequency and duration), demographical (household size), and technological (use volume or flowrate). We also include stochastic factors that govern energy to heat hot water: hot water fraction (percentage of hot water volume to total water volume used in a certain end-use event), heater water intake and dispense temperatures, and energy source for the heater (gas, electric, etc). From the empirical household end-use data, we derive stochastic probability distributions for each water and energy factor where each distribution represents the range and likelihood of values that the factor may take. The uncertainty of the stochastic water and energy factors is propagated using Monte Carlo simulations to calculate the composite probability distribution for water and energy use, potential savings, and payback periods to install efficient water end-use appliances and fixtures. Stochastic model results show the distributions among households for (i) water end-use, (ii) energy consumed to use water, and (iii) financial payback periods. Compared to deterministic analysis, stochastic modeling results show that hot water fractions for appliances follow normal distributions with high standard deviation and reveal pronounced variations among households that significantly affect energy savings and payback period estimates. These distributions provide an important tool to select and size water conservation programs to simultaneously meet both water and energy conservation goals. They also provide a way to identify and target a small fraction of customers with potential to save large water volumes and energy from appliance retrofits. Future work will embed this household scale stochastic model in city-scale models to identify win-win water management opportunities where households save money by conserving water and energy while cities avoid costs, downsize, or delay infrastructure development.

Energy data sourcebook for the US residential sector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wenzel, T.P.; Koomey, J.G.; Sanchez, M.

Analysts assessing policies and programs to improve energy efficiency in the residential sector require disparate input data from a variety of sources. This sourcebook, which updates a previous report, compiles these input data into a single location. The data provided include information on end-use unit energy consumption (UEC) values of appliances and equipment efficiency; historical and current appliance and equipment market shares; appliances and equipment efficiency and sales trends; appliance and equipment efficiency standards; cost vs. efficiency data for appliances and equipment; product lifetime estimates; thermal shell characteristics of buildings; heating and cooling loads; shell measure cost data for newmore » and retrofit buildings; baseline housing stocks; forecasts of housing starts; and forecasts of energy prices and other economic drivers. This report is the essential sourcebook for policy analysts interested in residential sector energy use. The report can be downloaded from the Web at http://enduse.lbl. gov/Projects/RED.html. Future updates to the report, errata, and related links, will also be posted at this address.« less

Household adoption of energy and water-efficient appliances: An analysis of attitudes, labelling and complementary green behaviours in selected OECD countries.

PubMed

Dieu-Hang, To; Grafton, R Quentin; Martínez-Espiñeira, Roberto; Garcia-Valiñas, Maria

2017-07-15

Using a household-based data set of more than 12,000 households from 11 OECD countries, we analyse the factors underlying the decision by households to adopt energy-efficient and water-efficient equipment. We evaluate the roles of both attitudes and labelling schemes on the adoption of energy and water-efficient equipment, and also the interaction and complementarity between energy and water conservation behaviours. Our findings show: one, 'green' social norms and favourable attitudes towards the environment are associated with an increased likelihood of households' adoption of energy and water-efficient appliances; two, households' purchase decisions are positively affected by their awareness, understanding, and trust of labelling schemes; and three, there is evidence of complementarity between energy conservation and water conservation behaviours. Copyright © 2017 Elsevier Ltd. All rights reserved.

Household energy consumption and expenditures 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-10-05

This presents information about household end-use consumption of energy and expenditures for that energy. These data were collected in the 1993 Residential Energy Consumption Survey; more than 7,000 households were surveyed for information on their housing units, energy consumption and expenditures, stock of energy-consuming appliances, and energy-related behavior. The information represents all households nationwide (97 million). Key findings: National residential energy consumption was 10.0 quadrillion Btu in 1993, a 9% increase over 1990. Weather has a significant effect on energy consumption. Consumption of electricity for appliances is increasing. Houses that use electricity for space heating have lower overall energy expendituresmore » than households that heat with other fuels. RECS collected data for the 4 most populous states: CA, FL, NY, TX.« less

Raising Public Awareness: The Role of the Household Sector in Mitigating Climate Change.

PubMed

Lin, Shis-Ping

2015-10-20

In addition to greenhouse gas emissions from the industrial, transportation and commercial sectors, emissions from the household sector also contribute to global warming. By examining residents of Taiwan (N = 236), this study aims to reveal the factors that influence households' intention to purchase energy-efficient appliances. The assessment in this study is based on the theory of planned behavior (TPB), and perceived benefit or cost (BOC) is introduced as an independent variable in the proposed efficiency action toward climate change (ECC) model. According to structural equation modeling, most of the indicators presented a good fit to the corresponding ECC model constructs. The analysis indicated that BOC is a good complementary variable to the TPB, as the ECC model explained 61.9% of the variation in intention to purchase energy-efficient appliances, which was higher than that explained by the TPB (58.4%). This result indicates that the ECC model is superior to the TPB. Thus, the strategy of promoting energy-efficient appliances in the household sector should emphasize global warming and include the concept of BOC.

Adult Competency Education Kit. Basic Skills in Speaking, Math, and Reading for Employment. Part H. ACE Competency Based Job Descriptions: #25--Household Appliance Mechanic; #26--Lineworker; #27--Painter Helper, Spray; #28--Painter, Brush; #29--Carpenter Apprentice.

ERIC Educational Resources Information Center

San Mateo County Office of Education, Redwood City, CA. Career Preparation Centers.

This fifth of fifteen sets of Adult Competency Education (ACE) Competency Based Job Descriptions in the ACE kit contains job descriptions for Household Appliance Mechanic; Lineworker; Painter Helper, Spray; Painter, Brush; and Carpenter Apprentice. Each begins with a fact sheet that includes this information: occupational title, D.O.T. code, ACE…

Householders' Mental Models of Domestic Energy Consumption: Using a Sort-And-Cluster Method to Identify Shared Concepts of Appliance Similarity.

PubMed

Gabe-Thomas, Elizabeth; Walker, Ian; Verplanken, Bas; Shaddick, Gavin

2016-01-01

If in-home displays and other interventions are to successfully influence people's energy consumption, they need to communicate about energy in terms that make sense to users. Here we explore householders' perceptions of energy consumption, using a novel combination of card-sorting and clustering to reveal shared patterns in the way people think about domestic energy consumption. The data suggest that, when participants were asked to group appliances which they felt naturally 'went together', there are relatively few shared ideas about which appliances are conceptually related. To the extent participants agreed on which appliances belonged together, these groupings were based on activities (e.g., entertainment) and location within the home (e.g., kitchen); energy consumption was not an important factor in people's categorisations. This suggests messages about behaviour change aimed at reducing energy consumption might better be tied to social practices than to consumption itself.

Measurements of intermediate-frequency electric and magnetic fields in households

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aerts, Sam, E-mail: sam.aerts@intec.ugent.be

Historically, assessment of human exposure to electric and magnetic fields has focused on the extremely-low-frequency (ELF) and radiofrequency (RF) ranges. However, research on the typically emitted fields in the intermediate-frequency (IF) range (300 Hz to 1 MHz) as well as potential effects of IF fields on the human body remains limited, although the range of household appliances with electrical components working in the IF range has grown significantly (e.g., induction cookers and compact fluorescent lighting). In this study, an extensive measurement survey was performed on the levels of electric and magnetic fields in the IF range typically present in residencesmore » as well as emitted by a wide range of household appliances under real-life circumstances. Using spot measurements, residential IF field levels were found to be generally low, while the use of certain appliances at close distance (20 cm) may result in a relatively high exposure. Overall, appliance emissions contained either harmonic signals, with fundamental frequencies between 6 kHz and 300 kHz, which were sometimes accompanied by regions in the IF spectrum of rather noisy, elevated field strengths, or much more capricious spectra, dominated by 50 Hz harmonics emanating far in the IF domain. The maximum peak field strengths recorded at 20 cm were 41.5 V/m and 2.7 A/m, both from induction cookers. Finally, none of the appliance emissions in the IF range exceeded the exposure summation rules recommended by the International Commission on Non-Ionizing Radiation Protection guidelines and the International Electrotechnical Commission (IEC 62233) standard at 20 cm and beyond (maximum exposure quotients EQ{sub E} 1.0 and {sub E}Q{sub H} 0.13). - Highlights: • Survey of residential electric and magnetic fields at intermediate frequencies (IF). • IF-EF and -MF emitted by 280 household appliances were characterised. • Strongest emitters were induction cookers, CFLs, LCD-TVs, and microwave ovens. • No emissions exceeded ICNIRP limits (highest exposure quotient was 1.00).« less

Behavior of urban residents toward the discarding of waste electrical and electronic equipment: a case study in Baoding, China.

PubMed

Li, Jinhui; Liu, Lili; Ren, Junshu; Duan, Huabo; Zheng, Lixia

2012-11-01

The volume of waste electrical and electronic equipment (WEEE) is growing rapidly worldwide, making its management difficult; therefore, this should be improved as a matter of urgency. WEEE includes both essential household appliances [including televisions, refrigerators, and washing machines; but not air conditioners, where the consumption mode is more like information, communication and technology (ICT)] ICT equipment (also called high-tech household appliances). In the present study, Baoding, a medium-sized, prefecture-level city in north central China with a population of 11 million, including 1.1 million urban residents, was selected as a representative city for an investigation of recycling behaviors. A valid sample size of 346 households in Baoding was investigated, and categorized into various income and educational levels. The results showed that the major reason for discarding WEEE was malfunction of the appliance, accounting for 52% of disposals. Surveyed households with either high income or good education were more likely to consume high-tech household appliances, attracted by advanced technology, versatile functions or flexibility of use. Personal computer ownership rates were highest in households with a high income and good education-1.2 and 0.9 per home respectively. WEEE was most often sold to peddlers or hawkers from where the WEEE flowed into the second-hand market to be refurbished or repaired, and then re-sold. However, 56.3% of residents in the college community were in support of charging consumers for disposal and 61.7% were in support of including a disposal surcharge in the purchase price of new products-a percentage approximately three times that for high-income residents. Thus, high educational level appears to be currently the most important factor in raising the potential of a household's willingness to pay for WEEE treatment cost. The findings of this study can be used to develop sound recycling systems for WEEE in mainland China.

Self-reported neurological symptoms in relation to CO emissions due to problem gas appliance installations in London: a cross-sectional survey.

PubMed

Croxford, Ben; Leonardi, Giovanni S; Kreis, Irene

2008-07-01

Previous research by the authors found evidence that up to 10% of particular household categories may be exposed to elevated carbon monoxide (CO) concentrations from poor quality gas appliance installations. The literature suggests certain neurological symptoms are linked to exposure to low levels of CO. This paper addresses the hypothesis that certain self-reported neurological symptoms experienced by a householder are linked to an estimate of their CO exposure. Between 27 April and 27 June 2006, 597 homes with a mains supply of natural gas were surveyed, mainly in old, urban areas of London. Qualified gas engineers tested all gas appliances (cooker, boiler, gas fire, and water heater) and reported, according to the Gas Industry Unsafe Situations Procedure, appliances considered At Risk (AR), Immediately Dangerous (ID) or Not to Current Standards (NCS). Five exposure risk categories were defined based on measurement of CO emitted by the appliance, its features and its use, with "high or very high" exposure category where occupants were considered likely to be exposed to levels greater than 26 ppm for one hour. The prevalence of symptoms at each level of exposure was compared with that at lowest level of exposure. Of the households, 6% were assessed as having a "high or very high" risk of exposure to CO. Of the individuals, 9% reported at least one neurological symptom. There was a statistically significant association between "high or very high" exposure risk to CO and self-reported symptoms compared to "no exposure" likelihood, for households not in receipt of benefit, controlling for "number of residents" and presence of pensioners, OR = 3.23 (95%CI: 1.28, 8.15). Risk ratios across all categories of exposure likelihood indicate a dose-response pattern. Those households in receipt of benefit showed no dose-response pattern. This study found an association between risk of CO exposure at low concentration, and prevalence of self-reported neurological symptoms in the community for those households not in receipt of benefit. As health status was self-reported, this association requires further investigation.

78 FR 1779 - Disclosures Regarding Energy Consumption and Water Use of Certain Home Appliances and Other...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-09

... looking at EnergyGuide labels, manufacturer advertising, or DOE certification data.\\43\\ \\42\\ 77 FR at... List of Subjects in 16 CFR Part 305 Advertising, Energy conservation, Household appliances, Labeling...

Warranty Decision Process.

DTIC Science & Technology

1982-02-01

come to expect when they purchase the products. Examples of this are found in the automobile, lawn - mower , household appliance and small engine...and stations--make significant acquisitions of commercial appliances such as washers, dryers, dishwashers, lawn - mowers and the like. Whichever command

Adapting Teaching Strategies To Encompass New Technologies.

ERIC Educational Resources Information Center

Oravec, Jo Ann

2001-01-01

The explosion of special-purpose computing devices--Internet appliances, handheld computers, wireless Internet, networked household appliances--challenges business educators attempting to provide computer literacy education. At a minimum, they should address connectivity, expanded applications, and social and public policy implications of these…

Load Modeling and Forecasting | Grid Modernization | NREL

Science.gov Websites

Load Modeling and Forecasting Load Modeling and Forecasting NREL's work in load modeling is focused resources (such as rooftop photovoltaic systems) and changing customer energy use profiles, new load models distribution system. In addition, NREL researchers are developing load models for individual appliances and

What's Inside?

ERIC Educational Resources Information Center

Sigford, Ann; Nelson, Nancy

1998-01-01

Presents a program for elementary teachers to learn how to use hand tools and household appliances to teach the principles of physics. The lesson helps teachers become familiar with simple hand tools, combat the apprehension of mechanical devices, and develop an interest in tools and technology. Session involves disassembling appliances to…

Laboratory Testing of Demand-Response Enabled Household Appliances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sparn, B.; Jin, X.; Earle, L.

2013-10-01

With the advent of the Advanced Metering Infrastructure (AMI) systems capable of two-way communications between the utility's grid and the building, there has been significant effort in the Automated Home Energy Management (AHEM) industry to develop capabilities that allow residential building systems to respond to utility demand events by temporarily reducing their electricity usage. Major appliance manufacturers are following suit by developing Home Area Network (HAN)-tied appliance suites that can take signals from the home's 'smart meter,' a.k.a. AMI meter, and adjust their run cycles accordingly. There are numerous strategies that can be employed by household appliances to respond tomore » demand-side management opportunities, and they could result in substantial reductions in electricity bills for the residents depending on the pricing structures used by the utilities to incent these types of responses.The first step to quantifying these end effects is to test these systems and their responses in simulated demand-response (DR) conditions while monitoring energy use and overall system performance.« less

Laboratory Testing of Demand-Response Enabled Household Appliances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sparn, B.; Jin, X.; Earle, L.

2013-10-01

With the advent of the Advanced Metering Infrastructure (AMI) systems capable of two-way communications between the utility's grid and the building, there has been significant effort in the Automated Home Energy Management (AHEM) industry to develop capabilities that allow residential building systems to respond to utility demand events by temporarily reducing their electricity usage. Major appliance manufacturers are following suit by developing Home Area Network (HAN)-tied appliance suites that can take signals from the home's 'smart meter,' a.k.a. AMI meter, and adjust their run cycles accordingly. There are numerous strategies that can be employed by household appliances to respond tomore » demand-side management opportunities, and they could result in substantial reductions in electricity bills for the residents depending on the pricing structures used by the utilities to incent these types of responses. The first step to quantifying these end effects is to test these systems and their responses in simulated demand-response (DR) conditions while monitoring energy use and overall system performance.« less

Characterization of electrical appliances in transient state

NASA Astrophysics Data System (ADS)

Wójcik, Augustyn; Winiecki, Wiesław

2017-08-01

The article contains the study about electrical appliance characterization on the basis of power grid signals. To represent devices, parameters of current and voltage signals recorded during transient states are used. In this paper only transients occurring as a result of switching on devices are considered. The way of data acquisition performed in specialized measurement setup developed for electricity load monitoring is described. The paper presents the method of transients detection and the method of appliance parameters calculation. Using the set of acquired measurement data and appropriate software the set of parameters for several household appliances operating in different operating conditions was processed. Usefulness of appliances characterization in Non-Intrusive Appliance Load Monitoring System (NIALMS) with the use of proposed method is discussed focusing on obtained results.

Extending or creating a new brand: evidence from a study on event-related potentials.

PubMed

Jin, Jia; Wang, Cuicui; Yu, Liping; Ma, Qingguo

2015-07-08

Brand strategy is a critical problem in new product promotion. In relation to this, producers typically have two main options, namely, brand extension and new brand creation. The current study investigated the neural basis of evaluating these brand strategies at the brain level by using event-related potentials. The experiment used a word-pair paradigm, in which the first word was either a famous beverage brand name or a newly created brand, and the second word was a product name from one of the two product categories (beverage or household appliance). Therefore, four conditions existed as follows: a famous beverage brand paired with a beverage product (BB) or with a household appliance (BH) and a newly created brand paired with a beverage product (NB) or with a household appliance (NH). Behavioral results showed that brand extension obtained a higher acceptance rate than new brand creation under the beverage product category; however, a lower acceptance rate was observed under the household appliance category. Moreover, at the brain level, BB elicited lower N400 mean amplitude than the new brand product NB, whereas BH led to higher N400 amplitude than the new brand product NH. These results showed that the likelihood of accepting a product depended on the association between the brand name and product name, and that the N400 could serve as an index of brand strategy evaluation. In addition, this study also confirmed that brand extension is not always the best brand strategy; an inappropriate extension sometimes performed worse than the creation of a new brand.

Raising Public Awareness: The Role of the Household Sector in Mitigating Climate Change

PubMed Central

Lin, Shis-Ping

2015-01-01

In addition to greenhouse gas emissions from the industrial, transportation and commercial sectors, emissions from the household sector also contribute to global warming. By examining residents of Taiwan (N = 236), this study aims to reveal the factors that influence households’ intention to purchase energy-efficient appliances. The assessment in this study is based on the theory of planned behavior (TPB), and perceived benefit or cost (BOC) is introduced as an independent variable in the proposed efficiency action toward climate change (ECC) model. According to structural equation modeling, most of the indicators presented a good fit to the corresponding ECC model constructs. The analysis indicated that BOC is a good complementary variable to the TPB, as the ECC model explained 61.9% of the variation in intention to purchase energy-efficient appliances, which was higher than that explained by the TPB (58.4%). This result indicates that the ECC model is superior to the TPB. Thus, the strategy of promoting energy-efficient appliances in the household sector should emphasize global warming and include the concept of BOC. PMID:26492262

Real-time identification of residential appliance events based on power monitoring

NASA Astrophysics Data System (ADS)

Yang, Zhao; Zhu, Zhicheng; Wei, Zhiqiang; Yin, Bo; Wang, Xiuwei

2018-03-01

Energy monitoring for specific home appliances has been regarded as the pre-requisite for reducing residential energy consumption. To enhance the accuracy of identifying operation status of household appliances and to keep pace with the development of smart power grid, this paper puts forward the integration of electric current and power data on the basis of existing algorithm. If average power difference of several adjacent cycles varies from the baseline and goes beyond the pre-assigned threshold value, the event will be flagged. Based on MATLAB platform and domestic appliances simulations, the results of tested data and verified algorithm indicate that the power method has accomplished desired results of appliance identification.

In-field measurements of PCDD/F emissions from domestic heating appliances for solid fuels.

PubMed

Hübner, C; Boos, R; Prey, T

2005-01-01

Within this project the emissions into the atmosphere of polychlorinated dibenzo-p-dioxins and -furans (PCDD/F) of 30 domestic heating appliances in Austrian households were tested. The appliances were single stoves (kitchen stove, continuous burning stove and tiled stove) and central heating boilers for solid fuels up to a nominal heat input of 50 kW. A main objective of this survey was to determine the PCDD/F emissions of domestic heating units under routine conditions. Therefore, the habitual combustion conditions used by the operators were not influenced. The original fuels and lightning supports were used and the operation of the units was carried out by the householders according to their usual practice. The data obtained were used to calculate in-field PCDD/F-emission factors. Most of the appliances have shown PCDD/F emissions within a concentration range of 0.01-0.3 ng TEQ/MJ. Modern fan-assisted wood heating boilers with afterburning and units for continuously burning of wood chips and wood pellets had the lowest emissions. High emissions were caused by unsuitable heating habits such as combustion of wastes and inappropriate operation of the appliances. There were only small differences between single stoves and central heating boilers or between wood and coal-fired appliances. The emission factors calculated are higher than those cited in literature, which are mainly derived from trials on test stands under laboratory conditions.

Household and caregiver characteristics and behaviours as predictors of unsafe exposure of children to paraffin appliances.

PubMed

Van Niekerk, A; Govender, R; Hornsby, N; Swart, L

2017-06-01

This study examines adult safety knowledge and practices regarding the use of paraffin cooking appliances. The use of these is common in South Africa with injury risks that are poorly understood. This cross-sectional study was in an informal settlement in Johannesburg, South Africa, where children were reportedly at high risk for burns. This study sought to clarify relationships between key risks and developed individual and composite variables from theoretical constructs and operational definitions of risks for burns. Risks included Child Use of Paraffin Appliances, Child Proximity to Cooking, Risky Stove Use, Caregiver's Burn Treatment Knowledge, Children Locked in House, Children Alone in House. Number of children remains as in proof as this was not a composite scale. Child Proximity to Cooking was associated with more children in the home. Households where children were in greater proximity to cooking were 6 times more likely to be left alone at home, with caregivers with no education over 100 times more likely to lock their children at home. Children locked in were often from homes where caregivers used appliances unsafely. In settings with hazardous energy use, compressed household configurations, and families with multiple children, Risky Stove Use and the practice of locking children in the home may be catastrophic. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Household energy use in urban Venezuela: Implications from surveys in Maracaibo, Valencia, Merida, and Barcelona-Puerto La Cruz

DOE Office of Scientific and Technical Information (OSTI.GOV)

Figueroa, M.J.; Sathaye, J.

1993-08-01

This report identifies the most important results of a comparative analysis of household commercial energy use in Venezuelan urban cities. The use of modern fuels is widespread among all cities. Cooking consumes the largest share of urban household energy use. The survey documents no use of biomass and a negligible use of kerosene for cooking. LPG, natural gas, and kerosene are the main fuels available. LPG is the fuel choice of low-income households in all cities except Maracaibo, where 40% of all households use natural gas. Electricity consumption in Venezuela`s urban households is remarkably high compared with the levels usedmore » in households in comparable Latin American countries and in households of industrialized nations which confront harsher climatic conditions and, therefore, use electricity for water and space heating. The penetration of appliances in Venezuela`s urban households is very high. The appliances available on the market are inefficient, and there are inefficient patterns of energy use among the population. Climate conditions and the urban built form all play important roles in determining the high level of energy consumption in Venezuelan urban households. It is important to acknowledge the opportunities for introducing energy efficiency and conservation in Venezuela`s residential sector, particularly given current economic and financial constraints, which may hamper the future provision of energy services.« less

A Web of Things-Based Emerging Sensor Network Architecture for Smart Control Systems.

PubMed

Khan, Murad; Silva, Bhagya Nathali; Han, Kijun

2017-02-09

The Web of Things (WoT) plays an important role in the representation of the objects connected to the Internet of Things in a more transparent and effective way. Thus, it enables seamless and ubiquitous web communication between users and the smart things. Considering the importance of WoT, we propose a WoT-based emerging sensor network (WoT-ESN), which collects data from sensors, routes sensor data to the web, and integrate smart things into the web employing a representational state transfer (REST) architecture. A smart home scenario is introduced to evaluate the proposed WoT-ESN architecture. The smart home scenario is tested through computer simulation of the energy consumption of various household appliances, device discovery, and response time performance. The simulation results show that the proposed scheme significantly optimizes the energy consumption of the household appliances and the response time of the appliances.

A Web of Things-Based Emerging Sensor Network Architecture for Smart Control Systems

PubMed Central

Khan, Murad; Silva, Bhagya Nathali; Han, Kijun

2017-01-01

The Web of Things (WoT) plays an important role in the representation of the objects connected to the Internet of Things in a more transparent and effective way. Thus, it enables seamless and ubiquitous web communication between users and the smart things. Considering the importance of WoT, we propose a WoT-based emerging sensor network (WoT-ESN), which collects data from sensors, routes sensor data to the web, and integrate smart things into the web employing a representational state transfer (REST) architecture. A smart home scenario is introduced to evaluate the proposed WoT-ESN architecture. The smart home scenario is tested through computer simulation of the energy consumption of various household appliances, device discovery, and response time performance. The simulation results show that the proposed scheme significantly optimizes the energy consumption of the household appliances and the response time of the appliances.  PMID:28208787

A Human-Centered Smart Home System with Wearable-Sensor Behavior Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ji, Jianting; Liu, Ting; Shen, Chao

Smart home has recently attracted much research interest owing to its potential in improving the quality of human life. How to obtain user's demand is the most important and challenging task for appliance optimal scheduling in smart home, since it is highly related to user's unpredictable behavior. In this paper, a human-centered smart home system is proposed to identify user behavior, predict their demand and schedule the household appliances. Firstly, the sensor data from user's wearable devices are monitored to profile user's full-day behavior. Then, the appliance-demand matrix is constructed to predict user's demand on home environment, which is extractedmore » from the history of appliance load data and user behavior. Two simulations are designed to demonstrate user behavior identification, appliance-demand matrix construction and strategy of appliance optimal scheduling generation.« less

Burns and fires in South Africa's informal settlements: Have approved kerosene stoves improved safety?

PubMed

Kimemia, David; van Niekerk, Ashley; Govender, Rajen; Seedat, Mohamed

2018-06-01

This study is a follow-on to an intervention project that implemented South African Bureau of Standards approved kerosene stoves and safety education in 150 households of a Johannesburg informal settlement. An investigation conducted 12 months later established that 43 stoves had operational defects, yet 23 households continued using the faulty appliances. This study focuses on (1) the psychological and behavioural factors associated with continued use of faulty stoves by the 23 households, and (2), the specific technical failures of these stoves. The study involved one-on-one recall interviews with the households using defective stoves (N=21) and laboratory-based stove tests for seven of the affected appliances. The results indicate that the stoves had defects in critical safety features such as flame control and the self-extinguishing mechanism. Four stove malfunctions of minor burn affect were reported in the study. Continued use of the damaged stoves was significantly associated with the time from receipt of the stove to detection of first failure: stoves that failed later on were more significantly likely to remain in use as compared to those that failed sooner. The findings point to the need for strengthening enforcement of appliance standards, public education on kerosene stove use, and structural change for the energy-poor. Copyright © 2017 Elsevier Ltd and ISBI. All rights reserved.

Sensors Expand the Capabilities of Robot Devices. Resources in Technology and Engineering

ERIC Educational Resources Information Center

Deal, Walter F., III; Hsiung, Steve C.

2017-01-01

Sensors of all kinds play significant roles in the way that we use and interact with technological devices today. Smartphones, household appliances, automobiles, and other products that we use every day incorporate many different kinds of sensors. While the sensors are hidden from view in the products, appliances, and tools that we use, they…

The impact of a home visitation programme on household hazards associated with unintentional childhood injuries: a randomised controlled trial.

PubMed

Odendaal, Willem; van Niekerk, Ashley; Jordaan, Esme; Seedat, Mohamed

2009-01-01

The continued high mortality and morbidity rates for unintentional childhood injuries remain a public health concern. This article reports on the influence of a home visitation programme (HVP) on household hazards associated with unintentional childhood injuries in a South African low-income setting. A randomised controlled trial (n=211 households) was conducted in a South African informal settlement. Community members were recruited and trained as paraprofessional visitors. Four intervention visits were conducted over 3 months, focusing on child development, and the prevention of burn, poison, and fall injuries. The HVP, a multi-component intervention, included educational inputs, provision of safety devices, and an implicit enforcement strategy. The intervention effect (IE) was measured with a standardised risk assessment index that compared post-intervention scores for intervention and control households. A significant reduction was observed in the hazards associated with electrical and paraffin appliances, as well as in hazards related to poisoning. Non-significant changes were observed for burn safety household practices and fall injury hazards. This study confirmed that a multi-component HVP effectively reduced household hazards associated with electrical and paraffin appliances and poisoning among children in a low-income South African setting.

Potential reuse of small household waste electrical and electronic equipment: Methodology and case study.

PubMed

Bovea, María D; Ibáñez-Forés, Valeria; Pérez-Belis, Victoria; Quemades-Beltrán, Pilar

2016-07-01

This study proposes a general methodology for assessing and estimating the potential reuse of small waste electrical and electronic equipment (sWEEE), focusing on devices classified as domestic appliances. Specific tests for visual inspection, function and safety have been defined for ten different types of household appliances (vacuum cleaner, iron, microwave, toaster, sandwich maker, hand blender, juicer, boiler, heater and hair dryer). After applying the tests, reuse protocols have been defined in the form of easy-to-apply checklists for each of the ten types of appliance evaluated. This methodology could be useful for reuse enterprises, since there is a lack of specific protocols, adapted to each type of appliance, to test its potential of reuse. After applying the methodology, electrical and electronic appliances (used or waste) can be segregated into three categories: the appliance works properly and can be classified as direct reuse (items can be used by a second consumer without prior repair operations), the appliance requires a later evaluation of its potential refurbishment and repair (restoration of products to working order, although with possible loss of quality) or the appliance needs to be finally discarded from the reuse process and goes directly to a recycling process. Results after applying the methodology to a sample of 87.7kg (96 units) show that 30.2% of the appliances have no potential for reuse and should be diverted for recycling, while 67.7% require a subsequent evaluation of their potential refurbishment and repair, and only 2.1% of them could be directly reused with minor cleaning operations. This study represents a first approach to the "preparation for reuse" strategy that the European Directive related to Waste Electrical and Electronic Equipment encourages to be applied. However, more research needs to be done as an extension of this study, mainly related to the identification of the feasibility of repair or refurbishment operations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Housing Characteristics: 2015 RECS Survey Data

EIA Publications

2017-01-01

The housing characteristics data tables from the 2015 RECS include: fuels used and end uses; structural and geographic characteristics; space heating; lighting; appliances; electronics; air conditioning; water heating; and household demographics. EIA’s 2015 RECS Household Survey captured more than 200 energy-related items from more than 5,600 households. The 2015 RECS is the 14th iteration of the program, which has been conducted periodically since 1978.

Personalized Energy Reduction Cyber-Physical System (PERCS): A gamified end-user platform for energy efficiency and demand response.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sintov, Nicole; Orosz, Michael; Schultz, P. Wesley

2015-01-01

The mission of the Personalized Energy Reduction Cyber-physical System (PERCS) is to create new possibilities for improving building operating efficiency, enhancing grid reliability, avoiding costly power interruptions, and mitigating greenhouse gas emissions. PERCS proposes to achieve these outcomes by engaging building occupants as partners in a user-centered smart service platform. Using a non-intrusive load monitoring approach, PERCS uses a single sensing point in each home to capture smart electric meter data in real time. The household energy signal is disaggregated into individual load signatures of common appliances (e.g., air conditioners), yielding near real-time appliance-level energy information. Users interact with PERCSmore » via a mobile phone platform that provides household- and appliance-level energy feedback, tailored recommendations, and a competitive game tied to energy use and behavioral changes. PERCS challenges traditional energy management approaches by directly engaging occupant as key elements in a technological system.« less

Microbial Diversity and Putative Opportunistic Pathogens in Dishwasher Biofilm Communities

PubMed Central

2018-01-01

ABSTRACT Extreme habitats are not only limited to natural environments, but also exist in manmade systems, for instance, household appliances such as dishwashers. Limiting factors, such as high temperatures, high and low pHs, high NaCl concentrations, presence of detergents, and shear force from water during washing cycles, define microbial survival in this extreme system. Fungal and bacterial diversity in biofilms isolated from rubber seals of 24 different household dishwashers was investigated using next-generation sequencing. Bacterial genera such as Pseudomonas, Escherichia, and Acinetobacter, known to include opportunistic pathogens, were represented in most samples. The most frequently encountered fungal genera in these samples belonged to Candida, Cryptococcus, and Rhodotorula, also known to include opportunistic pathogenic representatives. This study showed how specific conditions of the dishwashers impact the abundance of microbial groups and investigated the interkingdom and intrakingdom interactions that shape these biofilms. The age, usage frequency, and hardness of incoming tap water of dishwashers had significant impact on bacterial and fungal community compositions. Representatives of Candida spp. were found at the highest prevalence (100%) in all dishwashers and are assumed to be one of the first colonizers in recently purchased dishwashers. Pairwise correlations in tested microbiomes showed that certain bacterial groups cooccur, as did the fungal groups. In mixed bacterial-fungal biofilms, early adhesion, contact, and interactions were vital in the process of biofilm formation, where mixed complexes of bacteria and fungi could provide a preliminary biogenic structure for the establishment of these biofilms. IMPORTANCE Worldwide demand for household appliances, such as dishwashers and washing machines, is increasing, as is the number of immunocompromised individuals. The harsh conditions in household dishwashers should prevent the growth of most microorganisms. However, our research shows that persisting polyextremotolerant groups of microorganisms in household appliances are well established under these unfavorable conditions and supported by the biofilm mode of growth. The significance of our research is in identifying the microbial composition of biofilms formed on dishwasher rubber seals, how diverse abiotic conditions affect microbiota, and which key microbial members were represented in early colonization and contamination of dishwashers, as these appliances can present a source of domestic cross-contamination that leads to broader medical impacts. PMID:29330184

Quantifying Energy and Water Savings in the U.S. Residential Sector.

PubMed

Chini, Christopher M; Schreiber, Kelsey L; Barker, Zachary A; Stillwell, Ashlynn S

2016-09-06

Stress on water and energy utilities, including natural resource depletion, infrastructure deterioration, and growing populations, threatens the ability to provide reliable and sustainable service. This study presents a demand-side management decision-making tool to evaluate energy and water efficiency opportunities at the residential level, including both direct and indirect consumption. The energy-water nexus accounts for indirect resource consumption, including water-for-energy and energy-for-water. We examine the relationship between water and energy in common household appliances and fixtures, comparing baseline appliances to ENERGY STAR or WaterSense appliances, using a cost abatement analysis for the average U.S. household, yielding a potential annual per household savings of 7600 kWh and 39 600 gallons, with most upgrades having negative abatement cost. We refine the national average cost abatement curves to understand regional relationships, specifically for the urban environments of Los Angeles, Chicago, and New York. Cost abatement curves display per unit cost savings related to overall direct and indirect energy and water efficiency, allowing utilities, policy makers, and homeowners to consider the relationship between energy and water when making decisions. Our research fills an important gap of the energy-water nexus in a residential unit and provides a decision making tool for policy initiatives.

BLOND, a building-level office environment dataset of typical electrical appliances.

PubMed

Kriechbaumer, Thomas; Jacobsen, Hans-Arno

2018-03-27

Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of.

BLOND, a building-level office environment dataset of typical electrical appliances

NASA Astrophysics Data System (ADS)

Kriechbaumer, Thomas; Jacobsen, Hans-Arno

2018-03-01

Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of.

BLOND, a building-level office environment dataset of typical electrical appliances

PubMed Central

Kriechbaumer, Thomas; Jacobsen, Hans-Arno

2018-01-01

Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of. PMID:29583141

Managing Residential Electricity Demand Through Provision of Better Feedback

NASA Astrophysics Data System (ADS)

Collins, Myles

New and affordable technology for providing detailed feedback on household electricity usage presents a host of opportunities for utilities and policy-makers to manage demand. This dissertation examines ways to use these devices to reduce - and shift the timing of - energy use in the residential sector by influencing consumers' behavior. The first portion of the study analyzes the impact of programmable thermostats (PTs) on energy use, focusing on residents' knowledge of climate control settings in the dwelling. I found that of households with natural gas heating systems, young households with PTs used 17 percent less heating energy on average. In addition, residents who did not know their thermostat settings tended to use 10 percent more energy for heating. The main portion of the dissertation focuses specifically on the potential for better feedback on electricity usage to reduce household energy consumption. The existing literature suggests that feedback can reduce electricity consumption in homes by 5 to 20 percent, but that significant uncertainties remain in our knowledge of the effectiveness of feedback. These uncertainties include the variation in feedback effectiveness between demographic groups and consumers in different climate regions. This analysis uses these uncertainties to perform an exploratory analysis to determine the conditions under which the benefits of feedback outweigh the costs and to compare the cost-effectiveness of providing feedback against that of other DSM programs. I found that benefits would likely outweigh costs for enhanced monthly billing and real-time feedback and that cost-effectiveness was superior to that of other DSM programs for these types of feedback. For feedback that is disaggregated by appliance type, cost effectiveness was competitive with other DSM programs under a limited set of cases. This study also examines how energy consumption devices should display feedback on GHG emissions from electricity use under a real-time pricing program. I found that load-shifting can cause GHG emissions to increase or decrease depending on region and season and in no discernable pattern. Therefore, feedback may be more useful and comprehensible to households in the form of total GHG emissions attributable to electricity usage instead of the emission rate of the marginal power plant. Finally, this dissertation explores ways to maximize the effect of feedback by evaluating which appliances may be best suited for appliance-specific feedback. Due to the energy use and behavioral factors associated with each appliance, the most promising appliances were those that heat water for taps, showers, hot tubs, and waterbeds.

The Household Energy Game.

ERIC Educational Resources Information Center

Smith, Thomas W.; Jenkins, John

The Household Energy Game has been developed to provide some indication of energy use and individual management. The game is divided into two sections. In the first section, one is to devise one's own energy budget. Energy use is calculated in the areas of transportation, heating, hot water, air conditioning, and appliances. In each of these major…

UV emissions from artificial tanning devices and their compliance with the European technical standard.

PubMed

Facta, Stefania; Fusette, Stefania Saudino; Bonino, Alessandro; Anglesio, Laura; d'Amore, Giovanni

2013-04-01

Use of ultraviolet radiation-emitting tanning devices has been classified as "carcinogenic to humans" (group 1) by the International Agency for Research on Cancer. Following this classification, the knowledge of typical ultraviolet emission levels from tanning devices can be of interest for evaluating their impact on health. In this work, the results of an extensive measurement campaign on artificial tanning appliances are presented. Ultraviolet emissions from 94 tanning appliances produced by 15 different manufacturers were characterized by onsite spectroradiometric measurements. The measured radiometric quantities were compared with reference values fixed in the European technical standard EN 60335-2-27 "Household and similar electrical appliances-Safety. Part 2: Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation." Measurement results indicate that 88% of the examined appliances had ultraviolet emissions not compliant with the technical standard. Among the considered appliances, tanning devices equipped with low pressure lamps showed higher ultraviolet levels of effective irradiance and less compliance with standard requirements. In particular, UV emissions from 100% of low pressure appliances and from 78% of high pressure appliances exceeded the irradiance limit of 0.3 Wm set by the European technical standard.

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2012 CFR

2012-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2011 CFR

2011-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2013 CFR

2013-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

15 CFR 9.3 - Appliances and equipment included in program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... and central air conditioners, household refrigerators, home freezers, clothes washers, dishwashers, clothes dryers, kitchen ranges and ovens, water heaters, comfort heating equipment, and television...

Estimation of Operating Condition of Appliances Using Circuit Current Data on Electric Distribution Boards

NASA Astrophysics Data System (ADS)

Iwafune, Yumiko; Ogimoto, Kazuhiko; Yagita, Yoshie

The Energy management systems (EMS) on demand sides are expected as a method to enhance the capability of supply and demand balancing of a power system under the anticipated penetration of renewable energy generation such as Photovoltaics (PV). Elucidation of energy consumption structure in a building is one of important elements for realization of EMS and contributes to the extraction of potential energy saving. In this paper, we propose the estimation method of operating condition of household appliances using circuit current data on an electric distribution board. Circuit current data are broken down by their shape using a self-organization map method and aggregated by appliance based on customers' information of appliance possessed. Proposed method is verified using residential energy consumption measurement survey data.

Domesticating Physics: Introductory Physics Textbooks for Women in Home Economics in the United States, 1914-1955

ERIC Educational Resources Information Center

Behrman, Joanna

2017-01-01

Technologies such as electrical appliances entered American households on a large scale only after many decades of promotion to the public. The genre of "household physics" textbooks was one such form of promotion that was directed towards assumed white, female and largely middle-class home economics students. Published from the 1910s to…

15 CFR 9.5 - Participation of manufacturers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.5 Participation... Department of Commerce Labels and Energy Conservation Mark in advertising provided that the entire Label...

Multi-kanban mechanism for appliance disassembly

NASA Astrophysics Data System (ADS)

Udomsawat, Gun; Gupta, Surendra M.

2005-11-01

The use of household appliances continues to rise every year. A significant number of End-Of-Life (EOL) appliances are generated because of the introduction of newer models that are more attractive, efficient and affordable. Others are, of course, generated when they become non-functional. Many regulations encourage recycling of EOL appliances to reduce the amount of waste sent to landfills. In addition, EOL appliances offer the appliance manufacturing and remanufacturing industries a source of less expensive raw materials and components. For this reason product recovery has become a subject of interest during the past decade. In this paper, we study the disassembly line for appliance disassembly. We discuss and incorporate some of the complications that are inherent in disassembly line including product arrival, demand arrival, inventory fluctuation and production control mechanisms. We show how to overcome such complications by implementing a multi-kanban system in the appliance disassembly line setting. The multi-kanban system (MKS) relies on dynamic routing of kanbans according to the state of the system. We investigate the multi-kanban mechanism using simulation and explore the effect of product mix on performance of the traditional push system (TPS) and MKS in terms of controlling the system's inventory while attempting to achieve a decent customer service level.

Targeting water and energy conservation using big data

NASA Astrophysics Data System (ADS)

Escriva-Bou, A.; Pulido-Velazquez, M.; Lund, J. R.

2016-12-01

Water conservation is often the most cost effective source of additional water supply for water stressed regions to maintain supply reliability with increasing population and/or demands, or shorter-term droughts. In previous research we demonstrated how including energy savings of conserved water can increase willingness to adopt conservation measures, at the same time that increases energy and GHG emissions savings. But the capacity to save water, energy and GHG emissions depends fundamentally in the economic benefits for customers and utilities. Utilities have traditionally used rebates, subsidies or incentives to enhance water conservation. But the economic benefits originated by these rebates depend on the actual savings of the water, energy and GHG emissions. A crucial issue that is not considered in the financial analysis of these rebates is the heterogeneity in water consumption, resulting in rebating households that actually do not need improvements in certain appliances. Smart meters with end-use disaggregation allow to consider this heterogeneity and to target rebates. By using an optimization approach that minimizes water and energy residential costs—accounting for retrofit costs and individual benefits according to previous levels of consumption—we are able to assess economically optimal rebate programs both for customers and utilities. Three programs are considered: first, same economic incentives are provided to all households and then they do their optimal decisions; second, traditional appliance-focused rebates are assessed; and third, utilities provide only rebates to those households that maximize water, energy or GHG emissions savings. Results show that the most economically efficient options for households are not the best options for utilities, and that traditional appliance-focused rebates are much less optimal than targeted rebates.

15 CFR 9.1 - Goal of program.

Code of Federal Regulations, 2010 CFR

2010-01-01

.... (b) The goal of this program is to encourage manufacturers to provide consumers, at the point of sale... consumption and energy efficiency characteristics when purchasing household appliances and equipment and to...

Developing a Mixed Neural Network Approach to Forecast the Residential Electricity Consumption Based on Sensor Recorded Data

PubMed Central

Bâra, Adela; Stănică, Justina-Lavinia; Coculescu, Cristina

2018-01-01

In this paper, we report a study having as a main goal the obtaining of a method that can provide an accurate forecast of the residential electricity consumption, refining it up to the appliance level, using sensor recorded data, for residential smart homes complexes that use renewable energy sources as a part of their consumed electricity, overcoming the limitations of not having available historical meteorological data and the unwillingness of the contractor to acquire such data periodically in the future accurate short-term forecasts from a specialized institute due to the implied costs. In this purpose, we have developed a mixed artificial neural network (ANN) approach using both non-linear autoregressive with exogenous input (NARX) ANNs and function fitting neural networks (FITNETs). We have used a large dataset containing detailed electricity consumption data recorded by sensors, monitoring a series of individual appliances, while in the NARX case we have also used timestamps datasets as exogenous variables. After having developed and validated the forecasting method, we have compiled it in view of incorporating it into a cloud solution, being delivered to the contractor that can provide it as a service for a monthly fee to both the operators and residential consumers. PMID:29734761

Developing a Mixed Neural Network Approach to Forecast the Residential Electricity Consumption Based on Sensor Recorded Data.

PubMed

Oprea, Simona-Vasilica; Pîrjan, Alexandru; Căruțașu, George; Petroșanu, Dana-Mihaela; Bâra, Adela; Stănică, Justina-Lavinia; Coculescu, Cristina

2018-05-05

In this paper, we report a study having as a main goal the obtaining of a method that can provide an accurate forecast of the residential electricity consumption, refining it up to the appliance level, using sensor recorded data, for residential smart homes complexes that use renewable energy sources as a part of their consumed electricity, overcoming the limitations of not having available historical meteorological data and the unwillingness of the contractor to acquire such data periodically in the future accurate short-term forecasts from a specialized institute due to the implied costs. In this purpose, we have developed a mixed artificial neural network (ANN) approach using both non-linear autoregressive with exogenous input (NARX) ANNs and function fitting neural networks (FITNETs). We have used a large dataset containing detailed electricity consumption data recorded by sensors, monitoring a series of individual appliances, while in the NARX case we have also used timestamps datasets as exogenous variables. After having developed and validated the forecasting method, we have compiled it in view of incorporating it into a cloud solution, being delivered to the contractor that can provide it as a service for a monthly fee to both the operators and residential consumers.

75 FR 67615 - Appliance Labeling Rule

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-03

... current Rule indicates. List of Subjects in 16 CFR Part 305 Advertising, Energy conservation, Household..., distributor, retailer, or private labeler who advertises a covered product that is a ceiling fan in a catalog...

Progress towards Managing Residential Electricity Demand: Impacts of Standards and Labeling for Refrigerators and Air Conditioners in India

DOE Office of Scientific and Technical Information (OSTI.GOV)

McNeil, Michael A.; Iyer, Maithili

The development of Energy Efficiency Standards and Labeling (EES&L) began in earnest in India in 2001 with the Energy Conservation Act and the establishment of the Indian Bureau of Energy Efficiency (BEE). The first main residential appliance to be targeted was refrigerators, soon to be followed by room air conditioners. Both of these appliances are of critical importance to India's residential electricity demand. About 15percent of Indian households own a refrigerator, and sales total about 4 million per year, but are growing. At the same time, the Indian refrigerator market has seen a strong trend towards larger and more consumptivemore » frost-free units. Room air conditioners in India have traditionally been sold to commercial sector customers, but an increasing number are going to the residential sector. Room air conditioner sales growth in India peaked in the last few years at 20percent per year. In this paper, we perform an engineering-based analysis using data specific to Indian appliances. We evaluate costs and benefits to residential and commercial sector consumers from increased equipment costs and utility bill savings. The analysis finds that, while the BEE scheme presents net benefits to consumers, there remain opportunities for efficiency improvement that would optimize consumer benefits, according to Life Cycle Cost analysis. Due to the large and growing market for refrigerators and air conditioners in India, we forecast large impacts from the standards and labeling program as scheduled. By 2030, this program, if fully implemented would reduce Indian residential electricity consumption by 55 TWh. Overall savings through 2030 totals 385 TWh. Finally, while efficiency levels have been set for several years for refrigerators, labels and MEPS for these products remain voluntary. We therefore consider the negative impact of this delay of implementation to energy and financial savings achievable by 2030.« less

Estimating household water demand using revealed and contingent behaviors: Evidence from Vietnam

NASA Astrophysics Data System (ADS)

Cheesman, Jeremy; Bennett, Jeff; Son, Tran Vo Hung

2008-11-01

This article estimates the water demand of households using (1) municipal water exclusively and (2) municipal water and household well water in the capital city of Dak Lak Province in Vietnam. Household water demands are estimated using a panel data set formed by pooling household records of metered municipal water consumption and their stated preferences for water consumption contingent on hypothetical water prices. Estimates show that households using municipal water exclusively have very price inelastic demand. Households using municipal and household well water have more price elastic, but still inelastic, simultaneous water demand and treat municipal water and household well water as substitutes. Household water consumption is influenced by household water storage and supply infrastructure, income, and socioeconomic attributes. The demand estimates are used to forecast municipal water consumption by households in Buon Ma Thuot following an increase to the municipal water tariff to forecast the municipal water supply company's revenue stream following a tariff increase and to estimate the consumer surplus loss resulting from municipal water supply shortages.

Implications of end-user behaviour in response to deficiencies in water supply for electricity consumption - A case study of Delhi

NASA Astrophysics Data System (ADS)

Ghosh, Ruchira; Kansal, Arun; Aghi, Sakshi

2016-05-01

Over the past two decades, urban lifestyles have changed phenomenally. One aspect of this change is the increasing use of household appliances, which, in turn, influences water and electricity consumption in urban households. It is therefore necessary to revisit water supply norms in view of these behavioural changes. Increasing use of water-related appliances by the surveyed households in Delhi, India has lowered their water consumption but increased their electricity consumption (10-16 kW h a month). Also, longer working hours away from homes have shifted water demand from homes to commercial establishments and institutions. The per-capita water requirement to meet the basic needs for health and hygiene is approximately 76-78 L a day, of which bathing claims the largest share (32%). Nearly 70% of electricity consumption of a household is spent in coping with deficiencies in water supply. Strategies adopted by end users to save water were negatively correlated with those to save electricity. Household incomes have no influence on water consumption except in the case of those living in slums, who are forced to curtail their use of water even at the cost of health and hygiene; for the rest, coping with poor water supply amounts to spending nearly 50% more on electricity, defeating the purpose of subsidised water supply.

Factors Affecting Domestic Water Consumption in Rural Households upon Access to Improved Water Supply: Insights from the Wei River Basin, China

PubMed Central

Fan, Liangxin; Liu, Guobin; Wang, Fei; Geissen, Violette; Ritsema, Coen J.

2013-01-01

Comprehensively understanding water consumption behavior is necessary to design efficient and effective water use strategies. Despite global efforts to identify the factors that affect domestic water consumption, those related to domestic water use in rural regions have not been sufficiently studied, particularly in villages that have gained access to improved water supply. To address this gap, we investigated 247 households in eight villages in the Wei River Basin where three types of improved water supply systems are implemented. Results show that domestic water consumption in liters per capita per day was significantly correlated with water supply pattern and vegetable garden area, and significantly negatively correlated with family size and age of household head. Traditional hygiene habits, use of water appliances, and preference for vegetable gardening remain dominant behaviors in the villages with access to improved water supply. Future studies on rural domestic water consumption should pay more attention to user lifestyles (water appliance usage habits, outdoor water use) and cultural backgrounds (age, education). PMID:23977190

Factors affecting domestic water consumption in rural households upon access to improved water supply: insights from the Wei River Basin, China.

PubMed

Fan, Liangxin; Liu, Guobin; Wang, Fei; Geissen, Violette; Ritsema, Coen J

2013-01-01

Comprehensively understanding water consumption behavior is necessary to design efficient and effective water use strategies. Despite global efforts to identify the factors that affect domestic water consumption, those related to domestic water use in rural regions have not been sufficiently studied, particularly in villages that have gained access to improved water supply. To address this gap, we investigated 247 households in eight villages in the Wei River Basin where three types of improved water supply systems are implemented. Results show that domestic water consumption in liters per capita per day was significantly correlated with water supply pattern and vegetable garden area, and significantly negatively correlated with family size and age of household head. Traditional hygiene habits, use of water appliances, and preference for vegetable gardening remain dominant behaviors in the villages with access to improved water supply. Future studies on rural domestic water consumption should pay more attention to user lifestyles (water appliance usage habits, outdoor water use) and cultural backgrounds (age, education).

Electric emissions from electrical appliances.

PubMed

Leitgeb, N; Cech, R; Schröttner, J

2008-01-01

Electric emissions from electric appliances are frequently considered negligible, and standards consider electric appliances to comply without testing. By investigating 122 household devices of 63 different categories, it could be shown that emitted electric field levels do not justify general disregard. Electric reference values can be exceeded up to 11-fold. By numerical dosimetry with homogeneous human models, induced intracorporal electric current densities were determined and factors calculated to elevate reference levels to accounting for reduced induction efficiency of inhomogeneous fields. These factors were found not high enough to allow generally concluding on compliance with basic restrictions without testing. Electric appliances usually simultaneously emit both electric and magnetic fields exposing almost the same body region. Since the sum of induced current densities is limited, one field component reduces the available margin for the other. Therefore, superposition of electric current densities induced by either field would merit consideration.

Poisoning

MedlinePlus

... of illegal drugs Carbon monoxide from gas appliances Household products, such as laundry powder or furniture polish Pesticides ... products exactly as their labels say. Keep dangerous products where children ... call your local poison control center at 1-800-222-1222 right away.

Preliminary Study of Perception and Consumer Behaviour Towards Energy Saving for Household Appliances: A Case of Makassar

NASA Astrophysics Data System (ADS)

Syam Akil, Yusri; Mangngenre, Saiful; Mawar, Sri; Amar, Kifayah

2018-03-01

Electricity load has tendency to increase over the time. Therefore, efforts to maintain a balance between electricity supply and demand such as increasing energy saving related to the use of home electricity appliances are urgently needed. In general, one of the household appliances which consumes relatively high electricity energy is refrigerator. The purpose of this study is to analyze residential consumers perceptions and their behaviours about electricity energy saving in relation to the usage of household appliances in Makassar, Indonesia particularly for refrigerator. Moreover, typical relationship between perceptions and consumers behaviours is also analyzed by composed two regression models, namely model for usage behaviour (UREFm model) and model for habitual behaviour (HREFm model) by using general perception, specific perception, and external factors as explanation variables. To collect data, a questionnaire was designed for survey which involved 40 respondents as a preliminary study and then statistical tests including regression analysis were applied to analyze usable data. The target of respondent was an owner of a house in Makassar with installed power capacity at least 900 VA. Reliability test shown that all items in the developed questionnaire can be used for main survey as obtained Cronbach’s alpha values were above 0.6. Evaluation for consumers perceptions on energy saving in relation to demographic aspect using mean and Standard Deviation values indicated some significant differences. Other results regarding regression analysis shown that both composed models were well validated and had quite good fitness degree with adjusted R-squared values around 49.31% for UREFm model and 80.90% for HREFm model. Among considered variables, specific perception, and external factors were found have significant influence to the usage and habitual behaviours of consumers as confirmed by their p-values in each model below 0.05. Findings of this research can be used as a reference in developing programs for residential consumers such as electricity energy conservation program.

Developing a Practical Forecasting Screener for Domestic Violence Incidents

ERIC Educational Resources Information Center

Berk, Richard A.; He, Yan; Sorenson, Susan B.

2005-01-01

In this article, the authors report on the development of a short screening tool that deputies in the Los Angeles Sheriff's Department could use in the field to help forecast domestic violence incidents in particular households. The data come from more than 500 households to which sheriff's deputies were dispatched in fall 2003. Information on…

Electrical Injuries

MedlinePlus

... long you were exposed. Other factors include how healthy you are, and how quickly you get treatment. Causes of electrical injuries include Lightning strikes Faulty electrical appliances Work-related exposures Contact with household wiring or power lines Accidents in small children, when they bite ...

Slash Your Energy Bills.

ERIC Educational Resources Information Center

Lawrence, Allen

Tips are given here for energy conservation in the home. Included are heating and cooling houses, water heating, bathing, clothes washing and drying, cooking, refrigerating, dishwashing, lighting, and driving. Also included is a table of annual energy requirements of household electric appliances. (BB)

75 FR 57915 - Energy Conservation Program for Consumer Products: Notice of Petition for Waiver of the General...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-23

... Than Automobiles.'' (42 U.S.C. 6291-6309). Part A includes definitions, test procedures, labeling... marketer of household appliances, including, as relevant to this proceeding, clothes washers, files this...

Bread Basket: a gaming model for estimating home-energy costs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

An instructional manual for answering the twenty variables on COLORADO ENERGY's computerized program estimating home energy costs. The program will generate home-energy cost estimates based on individual household data, such as total square footage, number of windows and doors, number and variety of appliances, heating system design, etc., and will print out detailed costs, showing the percentages of the total household budget that energy costs will amount to over a twenty-year span. Using the program, homeowners and policymakers alike can predict the effects of rising energy prices on total spending by Colorado households.

Powering a Home with Just 25 Watts of Solar PV. Super-Efficient Appliances Can Enable Expanded Off-Grid Energy Service Using Small Solar Power Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phadke, Amol A.; Jacobson, Arne; Park, Won Young

Highly efficient direct current (DC) appliances have the potential to dramatically increase the affordability of off-grid solar power systems used for rural electrification in developing countries by reducing the size of the systems required. For example, the combined power requirement of a highly efficient color TV, four DC light emitting diode (LED) lamps, a mobile phone charger, and a radio is approximately 18 watts and can be supported by a small solar power system (at 27 watts peak, Wp). Price declines and efficiency advances in LED technology are already enabling rapidly increased use of small off-grid lighting systems in Africamore » and Asia. Similar progress is also possible for larger household-scale solar home systems that power appliances such as lights, TVs, fans, radios, and mobile phones. When super-efficient appliances are used, the total cost of solar home systems and their associated appliances can be reduced by as much as 50%. The results vary according to the appliances used with the system. These findings have critical relevance for efforts to provide modern energy services to the 1.2 billion people worldwide without access to the electrical grid and one billion more with unreliable access. However, policy and market support are needed to realize rapid adoption of super-efficient appliances.« less

2000-2001 California statewide household travel survey. Final report

DOT National Transportation Integrated Search

2002-06-01

The California Department of Transportation (Caltrans) maintains a statewide database of household socioeconomic and travel information, which is used in regional and statewide travel demand forecasting. The 2000-2001 California Statewide Household T...

Method for Evaluating Energy Use of Dishwashers, Clothes Washers, and Clothes Dryers: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eastment, M.; Hendron, R.

Building America teams are researching opportunities to improve energy efficiency for some of the more challenging end-uses, such as lighting (both fixed and occupant-provided), appliances (clothes washer, dishwasher, clothes dryer, refrigerator, and range), and miscellaneous electric loads, which are all heavily dependent on occupant behavior and product choices. These end-uses have grown to be a much more significant fraction of total household energy use (as much as 50% for very efficient homes) as energy efficient homes have become more commonplace through programs such as ENERGY STAR and Building America. As modern appliances become more sophisticated the residential energy analyst ismore » faced with a daunting task in trying to calculate the energy savings of high efficiency appliances. Unfortunately, most whole-building simulation tools do not allow the input of detailed appliance specifications. Using DOE test procedures the method outlined in this paper presents a reasonable way to generate inputs for whole-building energy-simulation tools. The information necessary to generate these inputs is available on Energy-Guide labels, the ENERGY-STAR website, California Energy Commission's Appliance website and manufacturer's literature. Building America has developed a standard method for analyzing the effect of high efficiency appliances on whole-building energy consumption when compared to the Building America's Research Benchmark building.« less

[Volatile organic compounds (VOCs) emitted from furniture and electrical appliances].

PubMed

Tanaka-Kagawa, Toshiko; Jinno, Hideto; Furukawa, Yoko; Nishimura, Tetsuji

2010-01-01

Organic chemicals are widely used as ingredients in household products. Therefore, furniture and other household products as well as building products may influence the indoor air quality. This study was performed to estimate quantitatively influence of household products on indoor air quality. Volatile organic compound (VOC) emissions were investigated for 10 products including furniture (chest, desk, dining table, sofa, cupboard) and electrical appliances (refrigerator, electric heater, desktop personal computer, liquid crystal display television and audio) by the large chamber test method (JIS A 1912) under the standard conditions of 28 degrees C, 50% relative humidity and 0.5 times/h ventilation. Emission rate of total VOC (TVOC) from the sofa showed the highest; over 7900 microg toluene-equivalent/unit/h. Relatively high TVOC emissions were observed also from desk and chest. Based on the emission rates, the impacts on the indoor TVOC were estimated by the simple model with a volume of 17.4 m3 and ventilation frequency of 0.5 times/h. The estimated TVOC increment for the sofa was 911 microg/m3, accounting for almost 230% of the provisional target value, 400 microg/m3. The values of estimated increment of toluene emitted from cupboard and styrene emitted from refrigerator were 10% and 16% of guideline values, respectively. These results revealed that VOC emissions from household products may influence significantly indoor air quality.

Does Consumer Confidence Forecast Household Saving and Borrowing Behavior? Evidence for Poland.

PubMed

Kłopocka, Aneta Maria

2017-01-01

Consumer confidence plays an important role in households' decision-making processes. This study investigates the effects of consumer confidence on household saving and borrowing behavior that are unsatisfactorily considered in previous discussions. The questions of interest are first, whether indexes of consumer confidence have any predictive power on their own for future household saving and borrowing rates, and second, whether they contain information about future household saving and borrowing rates aside from the information contained in other available indicators. In addition to aggregate confidence indicators, their components are used to provide more precise information. Overall, the multiple linear regression analysis (OLS technique) of Polish time-series data gives positive answers to both questions. This finding supports the recommendation of combining the strengths of objective indicators (such as economic fundamentals) and subjective indicators (such as consumer confidence) to improve household financial behavior forecasts.

Residential Energy Consumption Survey (RECS)

EIA Publications

2028-01-01

EIA administers the Residential Energy Consumption Survey (RECS) to a nationally representative sample of housing units. Traditionally, specially trained interviewers collect energy characteristics on the housing unit, usage patterns, and household demographics. Data include energy costs and usage for heating, cooling, appliances and other end uses.

12 CFR 535.1 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY PROHIBITED CONSUMER CREDIT PRACTICES (Eff... seeks or acquires goods, services, or money for personal, family, or household purposes, and who applies..., appliances, linens, china, crockery, kitchenware, and personal effects of the consumer and his or her...

The Attitudes of the Aged to Technology.

ERIC Educational Resources Information Center

James, Jeff

1993-01-01

Fifty-six older adults in Tasmania were interviewed about technology related to medical treatment, transportation, household appliances, banking, and computers. They were far less informed about computers; 34% overall and more than 50% of those over 60 were interested in learning more. (SK)

5 CFR 2634.305 - Liabilities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Administrative Personnel OFFICE OF GOVERNMENT ETHICS GOVERNMENT ETHICS EXECUTIVE BRANCH FINANCIAL DISCLOSURE... vehicle, household furniture, or appliances, provided that the loan does not exceed the purchase price of...,000, secured by family automobile purchased for $16,200. 6. Loan balance of $10,500, secured by...

Microwave processing heats up

USDA-ARS?s Scientific Manuscript database

Microwaves are a common appliance in many households. In the United States microwave heating is the third most popular domestic heating method food foods. Microwave heating is also a commercial food processing technology that has been applied for cooking, drying, and tempering foods. It's use in ...

Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management.

PubMed

Silva, Bhagya Nathali; Khan, Murad; Han, Kijun

2018-02-25

The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage domestic energy consumption. Hence, we propose a smart home energy management system that reduces unnecessary energy consumption by integrating an automated switching off system with load balancing and appliance scheduling algorithm. The load balancing scheme acts according to defined constraints such that the cumulative energy consumption of the household is managed below the defined maximum threshold. The scheduling of appliances adheres to the least slack time (LST) algorithm while considering user comfort during scheduling. The performance of the proposed scheme has been evaluated against an existing energy management scheme through computer simulation. The simulation results have revealed a significant improvement gained through the proposed LST-based energy management scheme in terms of cost of energy, along with reduced domestic energy consumption facilitated by an automated switching off mechanism.

Design and Implementation of a Smart Home System Using Multisensor Data Fusion Technology.

PubMed

Hsu, Yu-Liang; Chou, Po-Huan; Chang, Hsing-Cheng; Lin, Shyan-Lung; Yang, Shih-Chin; Su, Heng-Yi; Chang, Chih-Chien; Cheng, Yuan-Sheng; Kuo, Yu-Chen

2017-07-15

This paper aims to develop a multisensor data fusion technology-based smart home system by integrating wearable intelligent technology, artificial intelligence, and sensor fusion technology. We have developed the following three systems to create an intelligent smart home environment: (1) a wearable motion sensing device to be placed on residents' wrists and its corresponding 3D gesture recognition algorithm to implement a convenient automated household appliance control system; (2) a wearable motion sensing device mounted on a resident's feet and its indoor positioning algorithm to realize an effective indoor pedestrian navigation system for smart energy management; (3) a multisensor circuit module and an intelligent fire detection and alarm algorithm to realize a home safety and fire detection system. In addition, an intelligent monitoring interface is developed to provide in real-time information about the smart home system, such as environmental temperatures, CO concentrations, communicative environmental alarms, household appliance status, human motion signals, and the results of gesture recognition and indoor positioning. Furthermore, an experimental testbed for validating the effectiveness and feasibility of the smart home system was built and verified experimentally. The results showed that the 3D gesture recognition algorithm could achieve recognition rates for automated household appliance control of 92.0%, 94.8%, 95.3%, and 87.7% by the 2-fold cross-validation, 5-fold cross-validation, 10-fold cross-validation, and leave-one-subject-out cross-validation strategies. For indoor positioning and smart energy management, the distance accuracy and positioning accuracy were around 0.22% and 3.36% of the total traveled distance in the indoor environment. For home safety and fire detection, the classification rate achieved 98.81% accuracy for determining the conditions of the indoor living environment.

Residential energy use and conservation in Venezuela: Results and implications of a household survey in Caracas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Figueroa, M.J.; Ketoff, A.; Masera, O.

1992-10-01

This document presents the final report of a study of residential energy use in Caracas, the capital of Venezuela. It contains the findings of a household energy-use survey held in Caracas in 1988 and examines options for introducing energy conservation measures in the Venezuelan residential sector. Oil exports form the backbone of the Venezuelan economy. Improving energy efficiency in Venezuela will help free domestic oil resources that can be sold to the rest of the world. Energy conservation will also contribute to a faster recovery of the economy by reducing the need for major investments in new energy facilities, allowingmore » the Venezuelan government to direct its financial investments towards other areas of development. Local environmental benefits will constitute an important additional by-product of implementing energy-efficiency policies in Venezuela. Caracas`s residential sector shows great potential for energy conservation. The sector is characterized by high saturation levels of major appliances, inefficiency of appliances available in the market, and by careless patterns of energy use. Household energy use per capita average 6.5 GJ/per year which is higher than most cities in developing countries; most of this energy is used for cooking. Electricity accounts for 41% of all energy use, while LPG and natural gas constitute the remainder. Specific options for inducing energy conservation and energy efficiency in Caracas`s residential sector include energy-pricing policies, fuel switching, particularly from electricity to gas, improving the energy performance of new appliances and customer information. To ensure the accomplishment of an energy-efficiency strategy, a concerted effort by energy users, manufacturers, utility companies, government agencies, and research institutions will be needed.« less

Design and Implementation of a Smart Home System Using Multisensor Data Fusion Technology

PubMed Central

Chou, Po-Huan; Chang, Hsing-Cheng; Lin, Shyan-Lung; Yang, Shih-Chin; Su, Heng-Yi; Chang, Chih-Chien; Cheng, Yuan-Sheng; Kuo, Yu-Chen

2017-01-01

This paper aims to develop a multisensor data fusion technology-based smart home system by integrating wearable intelligent technology, artificial intelligence, and sensor fusion technology. We have developed the following three systems to create an intelligent smart home environment: (1) a wearable motion sensing device to be placed on residents’ wrists and its corresponding 3D gesture recognition algorithm to implement a convenient automated household appliance control system; (2) a wearable motion sensing device mounted on a resident’s feet and its indoor positioning algorithm to realize an effective indoor pedestrian navigation system for smart energy management; (3) a multisensor circuit module and an intelligent fire detection and alarm algorithm to realize a home safety and fire detection system. In addition, an intelligent monitoring interface is developed to provide in real-time information about the smart home system, such as environmental temperatures, CO concentrations, communicative environmental alarms, household appliance status, human motion signals, and the results of gesture recognition and indoor positioning. Furthermore, an experimental testbed for validating the effectiveness and feasibility of the smart home system was built and verified experimentally. The results showed that the 3D gesture recognition algorithm could achieve recognition rates for automated household appliance control of 92.0%, 94.8%, 95.3%, and 87.7% by the 2-fold cross-validation, 5-fold cross-validation, 10-fold cross-validation, and leave-one-subject-out cross-validation strategies. For indoor positioning and smart energy management, the distance accuracy and positioning accuracy were around 0.22% and 3.36% of the total traveled distance in the indoor environment. For home safety and fire detection, the classification rate achieved 98.81% accuracy for determining the conditions of the indoor living environment. PMID:28714884

77 FR 28805 - Energy Conservation Program: Test Procedures for Microwave Ovens

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-16

...On November 23, 2011, the U.S. Department of Energy (DOE) issued a supplemental notice of proposed rulemaking (SNOPR) to amend the test procedures for microwave ovens. That SNOPR proposed amendments to the DOE test procedure to incorporate provisions from the International Electrotechnical Commission (IEC) Standard 62301, ``Household electrical appliances--Measurement of standby power,'' Edition 2.0 2011-01 (IEC Standard 62301 (Second Edition)). Today's SNOPR proposes additional provisions for measuring the standby mode and off mode energy use of products that combine a microwave oven with other appliance functionality, as well as minor technical clarifications.

Estimating Price Elasticity using Market-Level Appliance Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fujita, K. Sydny

This report provides and update to and expansion upon our 2008 LBNL report “An Analysis of the Price Elasticity of Demand for Appliances,” in which we estimated an average relative price elasticity of -0.34 for major household appliances (Dale and Fujita 2008). Consumer responsiveness to price change is a key component of energy efficiency policy analysis; these policies influence consumer purchases through price both explicitly and implicitly. However, few studies address appliance demand elasticity in the U.S. market and public data sources are generally insufficient for rigorous estimation. Therefore, analysts have relied on a small set of outdated papers focusedmore » on limited appliance types, assuming long-term elasticities estimated for other durables (e.g., vehicles) decades ago are applicable to current and future appliance purchasing behavior. We aim to partially rectify this problem in the context of appliance efficiency standards by revisiting our previous analysis, utilizing data released over the last ten years and identifying additional estimates of durable goods price elasticities in the literature. Reviewing the literature, we find the following ranges of market-level price elasticities: -0.14 to -0.42 for appliances; -0.30 to -1.28 for automobiles; -0.47 to -2.55 for other durable goods. Brand price elasticities are substantially higher for these product groups, with most estimates -2.0 or more elastic. Using market-level shipments, sales value, and efficiency level data for 1989-2009, we run various iterations of a log-log regression model, arriving at a recommended range of short run appliance price elasticity between -0.4 and -0.5, with a default value of -0.45.« less

Communicating with whom? The effectiveness of appliance energy labels in the U.S. and Thailand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pont, P. du

The proliferation of household appliances is a global energy problem, and this comparative study of appliance energy labeling in the US and Thailand offers opportunities to learn from the implementation of programs in countries with different income levels and cultural and political climates. In the US, the author conducted participant observation in an appliance store and interviewed 16 policymakers, 14 salespeople, and 100 consumers. In Thailand, he interviewed 11 policymakers, 53 salespeople, and 62 consumers, and carried out a national survey of 971 consumers. This study is the first time that energy labels have been examined primarily as a problemmore » of consumer cognition in context--that is, how consumers read, interpret, and think about energy labels in the retail environment. After just three years of implementation, the Thai appliance labeling program is having a significantly greater impact on the consumer appliance market than is the 20-year-old US program. While Thai salespeople report that more than 60% of consumers ask about or look at the label, the corresponding number for the US is just 20%. Energy efficiency was reported among the top-three purchase priorities by 28% of Thai appliance consumers, compared to just 11% of US consumers. In his in-store tests of label cognition, the US EnergyGuide label fared poorly, and the Thai appliance label was more effective at helping consumers to identify efficient models. Yet both labels suffer from the problem of too much detailed product information, which hinders label comprehension.« less

7 CFR Exhibit E to Subpart A of... - Releasing Security Sales Proceeds and Determining “Essential” Family Living and Farm Operating...

Code of Federal Regulations, 2010 CFR

2010-01-01

..., food, clothing, medical care, house repair, transportation, insurance and household appliances, i.e... deciding whether an expense is essential and when deciding how much to release, the choices we make must be...

Determinants of residential electricity consumption: Using smart meter data to examine the effect of climate, building characteristics, appliance stock, and occupants' behavior

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kavousian, A; Rajagopal, R; Fischer, M

2013-06-15

We propose a method to examine structural and behavioral determinants of residential electricity consumption, by developing separate models for daily maximum (peak) and minimum (idle) consumption. We apply our method on a data set of 1628 households' electricity consumption. The results show that weather, location and floor area are among the most important determinants of residential electricity consumption. In addition to these variables, number of refrigerators and entertainment devices (e.g., VCRs) are among the most important determinants of daily minimum consumption, while number of occupants and high-consumption appliances such as electric water heaters are the most significant determinants of dailymore » maximum consumption. Installing double-pane windows and energy-efficient lights helped to reduce consumption, as did the energy-conscious use of electric heater. Acknowledging climate change as a motivation to save energy showed correlation with lower electricity consumption. Households with individuals over 55 or between 19 and 35 years old recorded lower electricity consumption, while pet owners showed higher consumption. Contrary to some previous studies, we observed no significant correlation between electricity consumption and income level, home ownership, or building age. Some otherwise energy-efficient features such as energy-efficient appliances, programmable thermostats, and insulation were correlated with slight increase in electricity consumption. (C) 2013 Elsevier Ltd. All rights reserved.« less

15 CFR 9.4 - Development of voluntary energy conservation specifications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 15 Commerce and Foreign Trade 1 2012-01-01 2012-01-01 false Development of voluntary energy... PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.4 Development of voluntary energy conservation specifications. (a) The Secretary in...

15 CFR 9.4 - Development of voluntary energy conservation specifications.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 15 Commerce and Foreign Trade 1 2013-01-01 2013-01-01 false Development of voluntary energy... PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.4 Development of voluntary energy conservation specifications. (a) The Secretary in...

15 CFR 9.4 - Development of voluntary energy conservation specifications.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 15 Commerce and Foreign Trade 1 2011-01-01 2011-01-01 false Development of voluntary energy... PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.4 Development of voluntary energy conservation specifications. (a) The Secretary in...

Environmentally friendly and cost-efficient analysis of aflatoxins in corn

USDA-ARS?s Scientific Manuscript database

The extraction procedure adds a significant cost to the overall expense of aflatoxin analysis in agricultural commodities. An inexpensive and low-waste extraction method using a household espresso coffee maker was tested. This appliance was used for the high-temperature /high-pressure extraction of ...

A Household Is Not a Person: Consistency of Pro-Environmental Behavior in Adult Couples and the Accuracy of Proxy-Reports

PubMed Central

Seebauer, Sebastian; Fleiß, Jürgen; Schweighart, Markus

2016-01-01

Studies on environmental behavior commonly assume single respondents to represent their entire household or employ proxy-reporting, where participants answer for other household members. It is contested whether these practices yield valid results. Therefore, we interviewed 84 couples, wherein both household members provided self- and proxy-reports for their partner. For use of electrical household appliances, consumption of hot water, space heating, everyday mobility, and environmental values, many variables fail to achieve criteria for validity. Consistency (agreement between self-reports of household members) is higher if behaviors are undertaken jointly or negotiated between partners. Accuracy (agreement of proxy-reports with corresponding self-reports) is higher for routine behaviors and for behaviors easily observable by the partner. Overall, indices perform better than items on single behaviors. We caution against employing individual responses in place of the entire household. Interventions for energy conservation should approach the specific person undertaking the target behavior. PMID:28670000

Household energy use in Asian cities: Responding to development success

NASA Astrophysics Data System (ADS)

Tyler, Stephen R.

In the past 10-15 years, gains in household income and urban development in many countries in Asia have led to significant shifts in household use of fuels away from traditional, biomass-based household fuels to modern, fossil fuels. These results suggest that, while the global atmospheric emissions implications need further analysis, the local air quality effects of urban household fuel use changes have been positive. These changes also demonstrate improvements in living conditions, particularly for poor women and children most affected by indoor air quality. However, for electricity use, where there is evidence of dramatic increases in household consumption, the longer term implications for atmospheric emissions are more troubling. Rapid demand growth in the urban household sector is contributing to huge increases in thermal electric generating capacity needs in Asia. Improving technologies of electricity use in the household sector appears to be easily achievable and could be stimulated through market and policy mechanisms which have been used elsewhere. These measures offer the prospect of real environmental and economic gains without sacrificing lifestyle advantages of electrical appliance use in households.

Microsimulation of household and firm behaviors : coupled models of land use and travel demand in Austin, Texas

DOT National Transportation Integrated Search

2007-12-01

Households and firms are key drivers of urban growth, yet models for forecasting travel demand often : ignore their dynamic evolution and several key decision processes. An understanding of household and : firm behavior over time is critical in antic...

Chapter 7: Refrigerator Recycling Evaluation Protocol. The Uniform Methods Project: Methods for Determining Energy-Efficiency Savings for Specific Measures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kurnik, Charles W.; Keeling, Josh; Bruchs, Doug

Refrigerator recycling programs are designed to save energy by removing operable, albeit less efficient, refrigerators from service. By offering free pickup, providing incentives, and disseminating information about the operating cost of less efficient refrigerators, these programs are designed to encourage consumers to: - Limit the use of secondary refrigerators -Relinquish refrigerators previously used as primary units when they are replaced (rather than keeping the existing refrigerator as a secondary unit) -Prevent the continued use of less efficient refrigerators in another household through a direct transfer (giving it away or selling it) or indirect transfer (resale on the used appliance market).more » Commonly implemented by third-party contractors (who collect and decommission participating appliances), these programs generate energy savings through the retirement of inefficient appliances. The decommissioning process captures environmentally harmful refrigerants and foam, and enables recycling of the plastic, metal, and wiring components.« less

Flexible Residential Smart Grid Simulation Framework

NASA Astrophysics Data System (ADS)

Xiang, Wang

Different scheduling and coordination algorithms controlling household appliances' operations can potentially lead to energy consumption reduction and/or load balancing in conjunction with different electricity pricing methods used in smart grid programs. In order to easily implement different algorithms and evaluate their efficiency against other ideas, a flexible simulation framework is desirable in both research and business fields. However, such a platform is currently lacking or underdeveloped. In this thesis, we provide a simulation framework to focus on demand side residential energy consumption coordination in response to different pricing methods. This simulation framework, equipped with an appliance consumption library using realistic values, aims to closely represent the average usage of different types of appliances. The simulation results of traditional usage yield close matching values compared to surveyed real life consumption records. Several sample coordination algorithms, pricing schemes, and communication scenarios are also implemented to illustrate the use of the simulation framework.

15 CFR 9.9 - Consumer education.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 15 Commerce and Foreign Trade 1 2011-01-01 2011-01-01 false Consumer education. 9.9 Section 9.9 Commerce and Foreign Trade Office of the Secretary of Commerce PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.9 Consumer education. The...

15 CFR 9.9 - Consumer education.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 15 Commerce and Foreign Trade 1 2012-01-01 2012-01-01 false Consumer education. 9.9 Section 9.9 Commerce and Foreign Trade Office of the Secretary of Commerce PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.9 Consumer education. The...

15 CFR 9.9 - Consumer education.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 15 Commerce and Foreign Trade 1 2013-01-01 2013-01-01 false Consumer education. 9.9 Section 9.9 Commerce and Foreign Trade Office of the Secretary of Commerce PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.9 Consumer education. The...

15 CFR 9.9 - Consumer education.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 15 Commerce and Foreign Trade 1 2014-01-01 2014-01-01 false Consumer education. 9.9 Section 9.9 Commerce and Foreign Trade Office of the Secretary of Commerce PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.9 Consumer education. The...

15 CFR 9.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Definitions. 9.2 Section 9.2 Commerce and Foreign Trade Office of the Secretary of Commerce PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.2 Definitions. (a) The term Secretary...

15 CFR 9.9 - Consumer education.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Consumer education. 9.9 Section 9.9 Commerce and Foreign Trade Office of the Secretary of Commerce PROCEDURES FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.9 Consumer education. The...

ACCESSING OVERSEAS MARKETS ENERGY EFFICIENCY STANDARDS AND APPLIANCE LABELING IN ASIA AND LATIN AMERICA

EPA Science Inventory

The purpose of the project is to reduce pollution and environmental degradation by increasing the efficiency of energy end-uses in the industrial and household sectors of key Asian and Latin American countries. This will be accomplished by encouraging the adoption and harmo...

15 CFR 9.7 - Department of Commerce energy conservation mark.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 15 Commerce and Foreign Trade 1 2013-01-01 2013-01-01 false Department of Commerce energy... FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.7 Department of Commerce energy conservation mark. The Department of Commerce shall develop an...

15 CFR 9.7 - Department of Commerce energy conservation mark.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 15 Commerce and Foreign Trade 1 2011-01-01 2011-01-01 false Department of Commerce energy... FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.7 Department of Commerce energy conservation mark. The Department of Commerce shall develop an...

15 CFR 9.7 - Department of Commerce energy conservation mark.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 15 Commerce and Foreign Trade 1 2012-01-01 2012-01-01 false Department of Commerce energy... FOR A VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.7 Department of Commerce energy conservation mark. The Department of Commerce shall develop an...

Latest Trends in Home Networking Technologies

NASA Astrophysics Data System (ADS)

Tsutsui, Akihiro

Broadband access service, including FTTH, is now in widespread use in Japan. More than half of the households that have broadband Internet access construct local area networks (home networks) in their homes. In addition, information appliances such as personal computers, networked audio, and visual devices and game machines are connected to home networks, and many novel service applications are provided via the Internet. However, it is still difficult to install and incorporate these devices and services because networked devices have been developed in different communities. I briefly explain the current status of information appliances and home networking technologies and services and discuss some of the problems in this and their solutions.

Life cycle assessment of central softening of very hard drinking water.

PubMed

Godskesen, B; Hauschild, M; Rygaard, M; Zambrano, K; Albrechtsen, H-J

2012-08-30

Many consumers prefer softened water due to convenience issues such as avoidance of removing limescale deposits from household appliances and surfaces, and to reduce consumption of cleaning agents and laundry detergents leading to lower household expenses. Even though central softening of drinking water entailed an increased use of energy, sand and chemicals at the waterworks, the distributed and softened drinking water supported a decrease in consumption of energy and chemical agents in the households along with a prolonged service life of household appliances which heat water. This study used Life Cycle Assessment (LCA) to quantify the environmental impacts of central softening of drinking water considering both the negative effects at the waterworks and the positive effects imposed by the changed water quality in the households. The LCA modeling considered central softening of drinking water from the initial hardness of the region of study (Copenhagen, Denmark) which is 362 mg/L as CaCO(3) to a final hardness as CaCO(3) of 254 (a softening depth of 108) mg/L or 145 (a softening depth of 217) mg/L. Our study showed that the consumer preference can be met together with reducing the impact on the environment and the resource consumption. Environmental impacts decreased by up to 3 mPET (milli Personal Equivalent Targeted) and the break-even point from where central softening becomes environmentally beneficial was reached at a softening depth of only 22 mg/L as CaCO(3). Both energy-related and chemically related environmental impacts were reduced as well as the consumption of resources. Based on scarcity criteria, nickel was identified as the most problematic non-renewable resource in the system, and savings of up to 8 mPR (milli Person Reserve) were found. Copyright © 2012 Elsevier Ltd. All rights reserved.

Estimating returns to scale and scale efficiency for energy consuming appliances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blum, Helcio; Okwelum, Edson O.

Energy consuming appliances accounted for over 40% of the energy use and $17 billion in sales in the U.S. in 2014. Whether such amounts of money and energy were optimally combined to produce household energy services is not straightforwardly determined. The efficient allocation of capital and energy to provide an energy service has been previously approached, and solved with Data Envelopment Analysis (DEA) under constant returns to scale. That approach, however, lacks the scale dimension of the problem and may restrict the economic efficient models of an appliance available in the market when constant returns to scale does not hold.more » We expand on that approach to estimate returns to scale for energy using appliances. We further calculate DEA scale efficiency scores for the technically efficient models that comprise the economic efficient frontier of the energy service delivered, under different assumptions of returns to scale. We then apply this approach to evaluate dishwashers available in the market in the U.S. Our results show that (a) for the case of dishwashers scale matters, and (b) the dishwashing energy service is delivered under non-decreasing returns to scale. The results further demonstrate that this method contributes to increase consumers’ choice of appliances.« less

Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management

PubMed Central

Silva, Bhagya Nathali; Khan, Murad; Han, Kijun

2018-01-01

The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage domestic energy consumption. Hence, we propose a smart home energy management system that reduces unnecessary energy consumption by integrating an automated switching off system with load balancing and appliance scheduling algorithm. The load balancing scheme acts according to defined constraints such that the cumulative energy consumption of the household is managed below the defined maximum threshold. The scheduling of appliances adheres to the least slack time (LST) algorithm while considering user comfort during scheduling. The performance of the proposed scheme has been evaluated against an existing energy management scheme through computer simulation. The simulation results have revealed a significant improvement gained through the proposed LST-based energy management scheme in terms of cost of energy, along with reduced domestic energy consumption facilitated by an automated switching off mechanism. PMID:29495346

Exploring the impact of network tariffs on household electricity expenditures using load profiles and socio-economic characteristics

NASA Astrophysics Data System (ADS)

Azarova, Valeriya; Engel, Dominik; Ferner, Cornelia; Kollmann, Andrea; Reichl, Johannes

2018-04-01

Growing self-generation and storage are expected to cause significant changes in residential electricity utilization patterns. Commonly applied volumetric network tariffs may induce imbalance between different groups of households and their respective contribution to recovering the operating costs of the grid. Understanding consumer behaviour and appliance usage together with socio-economic factors can help regulatory authorities to adapt network tariffs to new circumstances in a fair way. Here, we assess the effects of 11 network tariff scenarios on household budgets using real load profiles from 765 households. Thus we explore the possibly disruptive impact of applying peak-load-based tariffs on the budgets of households when they have been mainly charged for consumed volumes before. Our analysis estimates the change in household network expenditure for different combinations of energy, peak and fixed charges, and can help to design tariffs that recover the costs needed for the sustainable operation of the grid.

Improving socioeconomic land use forecasting for medium-sized metropolitan organizations in Virginia.

DOT National Transportation Integrated Search

2008-01-01

Socioeconomic forecasts are the foundation for long range travel demand modeling, projecting variables such as population, households, employment, and vehicle ownership. In Virginia, metropolitan planning organizations (MPOs) develop socioeconomic fo...

Inserts Automatically Lubricate Ball Bearings

NASA Technical Reports Server (NTRS)

Hager, J. A.

1983-01-01

Inserts on ball-separator ring of ball bearings provide continuous film of lubricant on ball surfaces. Inserts are machined or molded. Small inserts in ball pockets provide steady supply of lubricant. Technique is utilized on equipment for which maintenance is often poor and lubrication interval is uncertain, such as household appliances, automobiles, and marine engines.

Characterisation and materials flow management for waste electrical and electronic equipment plastics from German dismantling centres.

PubMed

Arends, Dagmar; Schlummer, Martin; Mäurer, Andreas; Markowski, Jens; Wagenknecht, Udo

2015-09-01

Waste electrical and electronic equipment is a complex waste stream and treatment options that work for one waste category or product may not be appropriate for others. A comprehensive case study has been performed for plastic-rich fractions that are treated in German dismantling centres. Plastics from TVs, monitors and printers and small household appliances have been characterised extensively. Based on the characterisation results, state-of-the-art treatment technologies have been combined to design an optimised recycling and upgrade process for each input fraction. High-impact polystyrene from TV casings that complies with the European directive on the restriction of hazardous substances (RoHS) was produced by applying continuous density separation with yields of about 60%. Valuable acrylonitrile butadiene styrene/polycarbonate can be extracted from monitor and printer casings by near-infrared-based sorting. Polyolefins and/or a halogen-free fraction of mixed styrenics can be sorted out by density separation from monitors and printers and small household appliances. Emerging separation technologies are discussed to improve recycling results. © The Author(s) 2015.

Disassembly properties and material characterisation of household small waste electric and electronic equipment.

PubMed

Bovea, María D; Pérez-Belis, Victoria; Ibáñez-Forés, Valeria; Quemades-Beltrán, Pilar

2016-07-01

This paper is focused on characterising small waste electric and electronic equipment, specifically small household appliances, from two different points of views: disassembly properties and material identification. The sample for this characterisation was obtained from a selective collection campaign organised in Castellón de la Plana (Spain). A total amount of 833.7kg (749 units) of small waste electric and electronic equipment was collected, of which 23.3% by weight and 22.4% by units belonged to the subcategory household equipment. This subcategory, composed of appliances such as vacuum cleaners, toasters, sandwich makers, hand blenders, juicers, coffee makers, hairdryers, scales, irons and heaters, was first disassembled in order to analyse different aspects of the disassembly process for each equipment type: type of joints, ease of identification of materials, ease of access to joints for extracting components, ease of separation of components from the whole, uniformity of tools needed for the disassembly process and possibility of reassembly after disassembly. Results show that the most common joints used in these equipment types are snap-fits and screws, although some permanent joints have also been identified. Next, the material composition of each component of each appliance belonging to each equipment type was identified visually and with additional mechanical trials and testing. It can be observed that plastic and electric/electronic components are present in all the equipment types analysed and are also the material fractions that appear with higher percentages in the material composition: 41.1wt% and 39.1wt% for the plastic fraction and electric/electronic components, respectively. The most common plastics are: polypropylene (PP), acrylonitrile butadiene styrene (ABS) and polycarbonate (PC), while the most common electric/electronic components are: cable, plug and printed circuit boards. Results also show that disassembly properties and material characterisation vary widely from one equipment type to another. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dynamic Appliances Scheduling in Collaborative MicroGrids System

PubMed Central

Bilil, Hasnae; Aniba, Ghassane; Gharavi, Hamid

2017-01-01

In this paper a new approach which is based on a collaborative system of MicroGrids (MG’s), is proposed to enable household appliance scheduling. To achieve this, appliances are categorized into flexible and non-flexible Deferrable Loads (DL’s), according to their electrical components. We propose a dynamic scheduling algorithm where users can systematically manage the operation of their electric appliances. The main challenge is to develop a flattening function calculus (reshaping) for both flexible and non-flexible DL’s. In addition, implementation of the proposed algorithm would require dynamically analyzing two successive multi-objective optimization (MOO) problems. The first targets the activation schedule of non-flexible DL’s and the second deals with the power profiles of flexible DL’s. The MOO problems are resolved by using a fast and elitist multi-objective genetic algorithm (NSGA-II). Finally, in order to show the efficiency of the proposed approach, a case study of a collaborative system that consists of 40 MG’s registered in the load curve for the flattening program has been developed. The results verify that the load curve can indeed become very flat by applying the proposed scheduling approach. PMID:28824226

Energy consumption and usage characteristics from field measurements of residential dishwashers, clothes washers and clothes dryers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, Y.L.; Grot, R.A.

1980-10-01

The measured energy consumption and usage characteristics for household dishwashers, clothes washers, and clothes dryers for ten townhouses at Twin Rivers, N.J., are presented. Whenever the dishwashers and/or clothes washers were in use, the energy consumption, water consumption, frequency of usage, and water temperature were measured by a data acquisition system. The electrical energy of electric clothes dryers and the gas consumption of gas clothes dryers were measured, as well as their frequency and duration of use, and exhaust temperature. Typical household usage patterns of these major appliances are included.

Power factor regulation for household usage

NASA Astrophysics Data System (ADS)

Daud, Nik Ghazali Nik; Hashim, Fakroul Ridzuan; Tarmizi, Muhammad Haziq Ahmad

2018-02-01

Power factor regulator technology has recently drawn attention to the consumer and to power generation company in order for consumers to use electricity efficiently. Controlling of power factor for efficient usage can reduce the production of power in fulfilment demands hence reducing the greenhouse effect. This paper presents the design method of power factor controller for household usage. There are several methods to improve the power factor. The power factor controller used by this method is by using capacitors. Total harmonic distortion also has become a major problem for the reliability of the electrical appliances and techniques to control it will be discussed.

How Primary School Students Understand Mains Electricity and Its Distribution. Research Report

ERIC Educational Resources Information Center

Pilatou, Vassiliki; Stavridou, Heleni

2004-01-01

The aim of this study was to detect primary students' conceptions about the origin and conveyance of electric current and about the connection of household electric appliances. In total, 383 students (aged 11-12) from the town of Volos, Greece, participated; 213 of them drawn from experimental classes and 170 from control groups. The results…

Variations in Figurative Language Use as a Function of Mode of Communication

ERIC Educational Resources Information Center

Boerger, Michael A.

2005-01-01

Various studies have demonstrated that the mode by which people communicate affects the content of their messages. The present study examines the ways in which one aspect of language use, namely figurative language, differs as a function of mode of communication. Subjects worked together in pairs to build a small household appliance, with an…

29 CFR Appendix A to Part 510 - Manufacturing Industries Eligible for Minimum Wage Phase-In

Code of Federal Regulations, 2011 CFR

2011-07-01

..., and surgical appliances and supplies. 3843 1 Dental equipment and supplies. 3844 a X-ray apparatus and..., upholstered. 2514 3 Metal household furniture. 2515 2 Mattresses, foundations, and convertible beds. 2517 3... earths, ground or otherwise treated. 3296 1 Mineral wool. 33 1 Primary metal industries. 331 1 Steel...

Kilowatt Counter: A Consumer's Guide to Energy Concepts, Quantities, and Uses.

ERIC Educational Resources Information Center

Friend, Gil; Morris, David

This booklet is a basic introduction to energy and energy usage. The first chapter discusses various forms of energy and how they are measured and converted from one to another with a unit conversion chart included. Tables and figures list annual energy requirements of household electrical appliances and energy requirements for houses with various…

JPRS Report, East Europe

DTIC Science & Technology

1988-10-18

minority nation- alities, as well as international agreements concerning the reunification of families . There shall be no national- istic, chauvinist...deteriorating and they are worried about the upkeep of their families . In my opinion, this reflects their inner strength; they enable the...business has joined forces with nudists . There is a bra shortage. The insufficient supply of household appliances (washing machines, refrigera- tors

The design of a comprehensive microsimulator of household vehicle fleet composition, utilization, and evolution.

DOT National Transportation Integrated Search

2012-01-01

The report describes a comprehensive vehicle fleet composition, utilization, and evolution : simulator that can be used to forecast household vehicle ownership and mileage by type of : vehicle over time. The components of the simulator are developed ...

RECS Data Show Decreased Energy Consumption per Household

EIA Publications

2012-01-01

Total United States energy consumption in homes has remained relatively stable for many years as increased energy efficiency has offset the increase in the number and average size of housing units, according to the newly released data from the Residential Energy Consumption Survey (RECS). The average household consumed 90 million British thermal units (Btu) in 2009 based on RECS. This continues the downward trend in average residential energy consumption of the last 30 years. Despite increases in the number and the average size of homes plus increased use of electronics, improvements in efficiency for space heating, air conditioning, and major appliances have all led to decreased consumption per household. Newer homes also tend to feature better insulation and other characteristics, such as double-pane windows, that improve the building envelope.

Research on application of modern household design and intellective household system

NASA Astrophysics Data System (ADS)

Zhang, Kaisheng; Zeng, Yuan; Fan, Junli

2009-07-01

People spend most of their lives indoors. To build a comfortable human environment, is always a dream for humankind. From ancient to now, the development of architecture imprints the progress of human civilization. However, for today's architecture, steel and concrete are only the surface. Intelligent technology will create its spirit and offer the soul. Nowadays, there's new meaning for the connotation of household design. This paper mainly discusses Design of Home Intelligent Electronic Assistant System Based on Embedded Module of S3C2410. Conerning the aspects of Home Security System, Automatic Meter Reading System, Automatic Control System for Electrical appliances, and Data Intelligence Communication System, it compactly describes the system's constitution diagram and hardware module, thus making better use of Home Intelligent Electronic Assistant System Based on Embedded Module.

Controller for thermostatically controlled loads

DOEpatents

Lu, Ning; Zhang, Yu; Du, Pengwei; Makarov, Yuri V.

2016-06-07

A system and method of controlling aggregated thermostatically controlled appliances (TCAs) for demand response is disclosed. A targeted load profile is formulated and a forecasted load profile is generated. The TCAs within an "on" or "off" control group are prioritized based on their operating temperatures. The "on" or "off" status of the TCAs is determined. Command signals are sent to turn on or turn off the TCAs.

Hey you! Shut the refrigerator door!

NASA Astrophysics Data System (ADS)

Fay, Sarah; Portenga, Angela

1998-09-01

The note discusses electrical power and energy and includes possible labs to be used in a physics classroom. It is based on our experimentation with a new device called the Watt-Watt/Hour Meter, which displays instantaneous power and cumulative energy readings of household electrical devices. Our experiments utilized this meter in conjunction with various appliances and focused primarily on its use with a refrigerator.

Residential exposure from extremely low frequency electromagnetic field (ELF EMF) radiation

NASA Astrophysics Data System (ADS)

Parthasarathy, Shamesh Raj; Tukimin, Roha

2018-01-01

ELF EMF radiation have received considerable attention as a potential threat to the safety and health of people living in the vicinity of high voltage transmission lines, electric distribution substations, power stations and even in close proximity to electronics and electrical household appliances. The paper highlights the study on the ELF EMF safety assessment performed at residences comprising of an owner-occupied house, a completed vacant house and an under construction condominium. The objectives of this study were to determine the ELF EMF radiation exposure level from the high voltage transmission line, electric distribution substation, power station and electrical household appliances in the residences, and to assess the potential exposure received by the occupants at the assessed locations. The results were logged in the electric and magnetic field strength with the units of volt per meter (V/m) and miliGauss (mG) respectively. The instrument setup and measurement protocols during the assessment were adopted from standard measurement method and procedures stipulated under the Institute of Electrical and Electronics Engineers (IEEE) Standard. The results were compared with the standards recommended in the International Commission on Non-Ionizing Radiation Protection (ICNIRP) guidelines.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Plas, R.J. van der

This paper presents results of two recent World Bank efforts made in Kenya, Niger, and Cameroon to study the impact of two different renewable projects, one a Micro-Lights program involving about 500 lanterns and the second a survey of 410 households using solar electricity systems. The Micro-Lights program showed that users have distinct preferences in the style of the lamps, that they are willing to spend cash, and that they demand good quality. They may be initially satisfied, but rapidly want more from their purchases. The photoelectric system survey touched less than 1% of such households, and looked at usermore » education, system size, satisfaction, expectations, age of system, appliances, and expectations.« less

Determinants of household water conservation: The role of demographic, infrastructure, behavior, and psychosocial variables

NASA Astrophysics Data System (ADS)

Fielding, Kelly S.; Russell, Sally; Spinks, Anneliese; Mankad, Aditi

2012-10-01

Securing water supplies in urban areas is a major challenge for policy makers, both now and into the future. This study aimed to identify the key determinants of household water use, with a view to identifying those factors that could be targeted in water demand management campaigns. Objective water use data and surveys were collected from 1008 households in four local government areas of southeast Queensland, Australia. Results showed that demographic, psychosocial, behavioral, and infrastructure variables all have a role to play in determining household water use. Consistent with past research, household occupancy was the most important predictor of water use. Households in regions recently exposed to drought conditions and higher-level restrictions also used less water than those who had less experience with drought. The effect of water efficient technology was mixed: some water efficient appliances were associated with less water use, while others were associated with more water use. Results also demonstrated the importance of considering water use as a collective behavior that is influenced by household dynamics. Households who reported a stronger culture of water conservation used less water. These findings, along with evidence that good water-saving habits are linked to water conservation, highlight the value of policies that support long-term cultural shifts in the way people think about and use water.

An electrical load measurements dataset of United Kingdom households from a two-year longitudinal study

PubMed Central

Murray, David; Stankovic, Lina; Stankovic, Vladimir

2017-01-01

Smart meter roll-outs provide easy access to granular meter measurements, enabling advanced energy services, ranging from demand response measures, tailored energy feedback and smart home/building automation. To design such services, train and validate models, access to data that resembles what is expected of smart meters, collected in a real-world setting, is necessary. The REFIT electrical load measurements dataset described in this paper includes whole house aggregate loads and nine individual appliance measurements at 8-second intervals per house, collected continuously over a period of two years from 20 houses. During monitoring, the occupants were conducting their usual routines. At the time of publishing, the dataset has the largest number of houses monitored in the United Kingdom at less than 1-minute intervals over a period greater than one year. The dataset comprises 1,194,958,790 readings, that represent over 250,000 monitored appliance uses. The data is accessible in an easy-to-use comma-separated format, is time-stamped and cleaned to remove invalid measurements, correctly label appliance data and fill in small gaps of missing data. PMID:28055033

Advances in Household Appliances- A Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bansal, Pradeep; Vineyard, Edward Allan; Abdelaziz, Omar

2011-01-01

An overview of options and potential barriers and risks for reducing the energy consumption, peak demand, and emissions for seven key energy consuming residential products (refrigerator-freezers, dishwashers, clothes washers, clothes dryers, electric ovens, gas ovens and microwave ovens) is presented. The paper primarily concentrates on the potential energy savings from the use of advanced technologies in appliances for the U.S. market. The significance and usefulness of each technology was evaluated in order to prioritize the R&D needs to improve energy efficiency of appliances in view of energy savings, cost, and complexity. The paper provides a snapshot of the future R&Dmore » needs for each of the technologies along with the associated barriers. Although significant energy savings may be achieved, one of the major barriers in most cases is high first cost. One way of addressing this issue and promoting the introduction of new technologies is to level the playing field for all manufacturers by establishing Minimum Energy Performance Standards (MEPS) which are not cost prohibitive and promoting energy efficient products through incentives to both manufacturers and consumers.« less

An electrical load measurements dataset of United Kingdom households from a two-year longitudinal study

NASA Astrophysics Data System (ADS)

Murray, David; Stankovic, Lina; Stankovic, Vladimir

2017-01-01

Smart meter roll-outs provide easy access to granular meter measurements, enabling advanced energy services, ranging from demand response measures, tailored energy feedback and smart home/building automation. To design such services, train and validate models, access to data that resembles what is expected of smart meters, collected in a real-world setting, is necessary. The REFIT electrical load measurements dataset described in this paper includes whole house aggregate loads and nine individual appliance measurements at 8-second intervals per house, collected continuously over a period of two years from 20 houses. During monitoring, the occupants were conducting their usual routines. At the time of publishing, the dataset has the largest number of houses monitored in the United Kingdom at less than 1-minute intervals over a period greater than one year. The dataset comprises 1,194,958,790 readings, that represent over 250,000 monitored appliance uses. The data is accessible in an easy-to-use comma-separated format, is time-stamped and cleaned to remove invalid measurements, correctly label appliance data and fill in small gaps of missing data.

An electrical load measurements dataset of United Kingdom households from a two-year longitudinal study.

PubMed

Murray, David; Stankovic, Lina; Stankovic, Vladimir

2017-01-05

Smart meter roll-outs provide easy access to granular meter measurements, enabling advanced energy services, ranging from demand response measures, tailored energy feedback and smart home/building automation. To design such services, train and validate models, access to data that resembles what is expected of smart meters, collected in a real-world setting, is necessary. The REFIT electrical load measurements dataset described in this paper includes whole house aggregate loads and nine individual appliance measurements at 8-second intervals per house, collected continuously over a period of two years from 20 houses. During monitoring, the occupants were conducting their usual routines. At the time of publishing, the dataset has the largest number of houses monitored in the United Kingdom at less than 1-minute intervals over a period greater than one year. The dataset comprises 1,194,958,790 readings, that represent over 250,000 monitored appliance uses. The data is accessible in an easy-to-use comma-separated format, is time-stamped and cleaned to remove invalid measurements, correctly label appliance data and fill in small gaps of missing data.

[Demography perspectives and forecasts of the demand for electricity].

PubMed

Roy, L; Guimond, E

1995-01-01

"Demographic perspectives form an integral part in the development of electric load forecasts. These forecasts in turn are used to justify the addition and repair of generating facilities that will supply power in the coming decades. The goal of this article is to present how demographic perspectives are incorporated into the electric load forecasting in Quebec. The first part presents the methods, hypotheses and results of population and household projections used by Hydro-Quebec in updating its latest development plan. The second section demonstrates applications of such demographic projections for forecasting the electric load, with a focus on the residential sector." (SUMMARY IN ENG AND SPA) excerpt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blair, Jeff L.; Glenn, Lee J.

The Smart Grid opens the door to the development of many companion technologies which will in turn enable the development of a variety of devices for household electricity-consuming appliances that can communicate with it; especially, many major appliance manufacturers (such as Whirlpool and General Electric) have made public commitments to design their appliances to be Smart Grid-compatible over the next several years. Yet during that same time period, customers will purchase many millions of long-lasting appliances which are not compatible with the Smart Grid. This research project's purpose is to bring significant Smart Grid compatibility to previously-installed appliances that weremore » not specifically designed for any Smart Grid communications, in a way that is both economical and attractive for users who want to share in the energy cost savings and reduction of peak power demand opportunities provided by the evolving Smart Grid infrastructure. The focus of this effort is to identify and research smart control solutions which take advantage of the effective strategies of demand-response (DR) communications from utilities [including time-of-day (TOD) and peak-demand pricing options] and function apart from any need for operational changes to be designed into the non-smart appliances. Our Phase I concepts promote technological advancements for enabling devices that shift the available-use time of millions of different appliances which otherwise have no Smart Grid capability. We researched low-cost microcontroller-based ways of creating devices with the ability to: (1) maintain an accurate time and day (with no need for battery backup throughout a power outage); (2) perform two-way wired and wireless communications directly with the utility company's demand management signals, to identify both low-cost time periods as well as critical-reduction periods when the cost of energy use would otherwise be much higher; (3) measure the power usage of the connected non-smart appliance; and (4) remove power for a period of time from the appliance (such as a dehumidifier, portable heater, or pool pump) in response to both time-pricing schedule and critical peak-load information from the utility, or inform the user of a batch-type appliance (such as a clothes dryer or dishwasher) regarding the current cost associated with using the appliance. The new products that could be developed as a result of this research into new consumer-centric features and characteristics includes smart wall outlets, smart outlet power-monitoring adapters, smart load switches and smart remote electric rate indicators associated with the non-smart appliances. Our Phase I goal of determining the feasibility of the above technologies was successful. The objectives were also met of developing concepts for a family of microprocessor-based control/indicator devices that can provide the above capabilities while connected in series between an appliance and its electrical power source and/or while indicating cost-of-use status to the appliance user.« less

Association of early-life exposure to household gas appliances and indoor nitrogen dioxide with cognition and attention behavior in preschoolers.

PubMed

Morales, Eva; Julvez, Jordi; Torrent, Maties; de Cid, Rafael; Guxens, Mònica; Bustamante, Mariona; Künzli, Nino; Sunyer, Jordi

2009-06-01

The authors investigated the association of early-life exposure to indoor air pollution with neuropsychological development in preschoolers and assessed whether this association differs by glutathione-S-transferase gene (GSTP1) polymorphisms. A prospective, population-based birth cohort was set up in Menorca, Spain, in 1997-1999 (n = 482). Children were assessed for cognitive functioning (McCarthy Scales of Children's Abilities) and attention-hyperactivity behaviors (Diagnostic and Statistical Manual of Mental Disorders, 4th Edition) at age 4 years. During the first 3 months of life, information about gas appliances at home and indoor nitrogen dioxide concentration was collected at each participant's home (n = 398, 83%). Genotyping was conducted for the GSTP1 coding variant Ile105Val. Use of gas appliances was inversely associated with cognitive outcomes (beta coefficient for general cognition = -5.10, 95% confidence interval (CI): -9.92, -0.28; odds ratio for inattention symptoms = 3.59, 95% CI: 1.14, 11.33), independent of social class and other confounders. Nitrogen dioxide concentrations were associated with cognitive function (a decrease of 0.27 point per 1 ppb, 95% CI: -0.48, -0.07) and inattention symptoms (odds ratio = 1.06, 95% CI: 1.01, 1.12). The deleterious effect of indoor pollution from gas appliances on neuropsychological outcomes was stronger in children with the GSTP1 Val-105 allele. Early-life exposure to air pollution from indoor gas appliances may be negatively associated with neuropsychological development through the first 4 years of life, particularly among genetically susceptible children.

Household related predictors of burn injuries in an Iranian population: a case–control study

PubMed Central

2012-01-01

Background To prevent burn injuries it is vital to have sound information on predictors of its occurrence in different settings. Ardabil Province is the coldest province of Iran with high burden of burn injuries. The aim of this study was to determine the household related predictors of unintentional burns in Ardabil Province located at North-West of Iran. Methods The study was conducted through a hospital based case–control design. 239 burn victims as well as 246 hospital-based controls were enrolled. Both bivariate and multivariate analysis methods were used. Results Males comprised 55.2% of all the study subjects. Mean age of the participants was 21.8 years (95% CI: 19.17-24.4). The economic ability of the households was associated with risk of burn injuries. Multivariate conditional logistic regression results showed the following variables to be independent factors associated with burn injuries. Using non-conventional pipe-less air heaters instead of conventional piped kerosene- or gas-burning heaters (Odds ratio: 1.98, 95% CI: 1.1-3.6). Common use of picnic gas-stove for cooking at home (odds ratio = 1.6, 95%CI: 1–2.4). Using electric samovars instead of other types of samovars (Odds ratio = 0.3, 95% CI: 0.1-1). Using samovars lacking the national standard authorization mark (Odds ratio = 2.2, 95% CI: 1.4-3.6). Conclusion Using some types of specific heating or cooking appliances, and unsafe use of conventional appliances were major risk predictors of burn injuries in this population. PMID:22571762

Household furniture tip-over deaths of young children.

PubMed

Wolf, Barbara C; Harding, Brett E

2011-07-01

The potential for the injury or death of a child resulting from the tip-over of a piece of household furniture or a domestic appliance has not been previously well recognized. We reviewed nine accidental deaths of young children that resulted from avoidable residential hazards and/or lapses in supervision of the children by their caregivers. The offending household items included televisions, bedroom dressers, a kitchen stove, and a lounge chair. The causes of death were mechanical asphyxia, blunt trauma, and combined blunt head trauma and asphyxia. All of the deaths could have been prevented by appropriate anchoring of the piece of furniture and/or closer supervision of the child. A thorough multidisciplinary investigation is essential in establishing the cause and manner of death in such cases and in identifying risk factors that may aid in the prevention of future childhood deaths. © 2011 American Academy of Forensic Sciences.

Project monitor. Final report. [Allegheny County, PA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammond, P.Y.; Beck, P.; Doctors, S.I.

1979-04-27

Results are reported of a study of consumers' energy attitudes and behavior. Household consumers and small business consumers (both retail and manufacturing) responded to the survey, but only the household results are reported. The study sought to understand energy-related behavior at the level where the various components of energy policy intersect. Attempts are made to attain this goal by determining the extent to which various properties of the individuals and firms are associated with various amounts of conservation. A representative sample of the adult population in Allegheny County, Pennsylvania was interviewed. Part I introduces the measures of household conservation tomore » be used in the survey. Part II analyzes each of the types of energy conservation - general, winterization, heating, cooling, appliance, transportation, and electricity reductions - and relates them to demographic, situation, attitudinal, and perceptual variables in the household sample. Part III deals with the impacts of Project Pacesetter and the United Mine Workers' strike against the coal operators - particularly, the impact of the coal strike on household residents of Allegheny County. Part IV summarizes the findings and uses them for recommendations regarding energy conservation policy. Additional data are presented in 4 appendices. (MCW)« less

76 FR 49237 - Energy Conservation Program: Test Procedures for Residential Clothes Washers

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-09

...In this supplemental notice of proposed rulemaking (SNOPR), the U.S. Department of Energy (DOE) proposes to revise its test procedure for residential clothes washers established under the Energy Policy and Conservation Act (EPCA). DOE proposes to incorporate provisions of the International Electrotechnical Commission (IEC) Standard 62301, ``Household electrical appliances--Measurement of standby power'' (Second Edition). DOE also proposes to update the provisions for measuring active mode energy and water consumption.

JPRS Report, Soviet Union, International Affairs

DTIC Science & Technology

1990-07-06

household appliances. " Samsung " has divisions in the USA and Mexico, England, Portugal and Spain, Thailand and Malaysia . Construction of four new... Samsung Corporation. Samsung —"Three Stars"—unites 37 companies of dif- ferent description which produce textiles and sugar, build ships, hotels and...nition throughout the world primarily for its broad spectrum of electronic products. Out of 150,000 employees (the ratio of "blue" to "white" collar

EPA ENERGY STAR: Tackling Growth in Home Electronics and Small Appliances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanchez, Marla Christine; Brown, Richard; Homan, Gregory

2008-11-17

Over a decade ago, the electricity consumption associated with home electronics and other small appliances emerged onto the global energy policy landscape as one of the fastest growing residential end uses with the opportunity to deliver significant energy savings. As our knowledge of this end use matures, it is essential to step back and evaluate the degree to which energy efficiency programs have successfully realized energy savings and where savings opportunities have been missed.For the past fifteen years, we have quantified energy, utility bill, and carbon savings for US EPA?s ENERGY STAR voluntary product labeling program. In this paper, wemore » present a unique look into the US residential program savings claimed to date for EPA?s ENERGY STAR office equipment, consumer electronics, and other small household appliances as well as EPA?s projected program savings over the next five years. We present a top-level discussion identifying program areas where EPA?s ENERGY STAR efforts have succeeded and program areas where ENERGY STAR efforts did not successfully address underlying market factors, technology issues and/or consumer behavior. We end by presenting the magnitude of ?overlooked? savings.« less

Optimization Based Data Mining Approah for Forecasting Real-Time Energy Demand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Omitaomu, Olufemi A; Li, Xueping; Zhou, Shengchao

The worldwide concern over environmental degradation, increasing pressure on electric utility companies to meet peak energy demand, and the requirement to avoid purchasing power from the real-time energy market are motivating the utility companies to explore new approaches for forecasting energy demand. Until now, most approaches for forecasting energy demand rely on monthly electrical consumption data. The emergence of smart meters data is changing the data space for electric utility companies, and creating opportunities for utility companies to collect and analyze energy consumption data at a much finer temporal resolution of at least 15-minutes interval. While the data granularity providedmore » by smart meters is important, there are still other challenges in forecasting energy demand; these challenges include lack of information about appliances usage and occupants behavior. Consequently, in this paper, we develop an optimization based data mining approach for forecasting real-time energy demand using smart meters data. The objective of our approach is to develop a robust estimation of energy demand without access to these other building and behavior data. Specifically, the forecasting problem is formulated as a quadratic programming problem and solved using the so-called support vector machine (SVM) technique in an online setting. The parameters of the SVM technique are optimized using simulated annealing approach. The proposed approach is applied to hourly smart meters data for several residential customers over several days.« less

Consumers’ perceptions of energy use and energy savings: A literature review

NASA Astrophysics Data System (ADS)

Lesic, Vedran; Bruine de Bruin, Wändi; Davis, Matthew C.; Krishnamurti, Tamar; Azevedo, Inês M. L.

2018-03-01

Background. Policy makers and program managers need to better understand consumers’ perceptions of their energy use and savings to design effective strategies for promoting energy savings. Methods. We reviewed 14 studies from the emerging interdisciplinary literature examining consumers’ perceptions electricity use by specific appliances, and potential savings. Results. We find that: (1) electricity use is often overestimated for low-energy consuming appliances, and underestimated for high-energy consuming appliances; (2) curtailment strategies are typically preferred over energy efficiency strategies; (3) consumers lack information about how much electricity can be saved through specific strategies; (4) consumers use heuristics for assessing the electricity use of specific appliances, with some indication that more accurate judgments are made among consumers with higher numeracy and stronger pro-environmental attitudes. However, design differences between studies, such as variations in reference points, reporting units and assessed time periods, may affect consumers’ reported perceptions. Moreover, studies differ with regard to whether accuracy of perceptions was evaluated through comparisons with general estimates of actual use, self-reported use, household-level meter readings, or real-time smart meter readings. Conclusion. Although emerging findings are promising, systematic variations in the measurement of perceived and actual electricity use are potential cause for concern. We propose avenues for future research, so as to better understand, and possibly inform, consumers’ perceptions of their electricity use. Ultimately, this literature will have implications for the design of effective electricity feedback for consumers, and related policies.

Environmental benefit analysis of strategies for potable water savings in residential buildings.

PubMed

Marinoski, Ana Kelly; Rupp, Ricardo Forgiarini; Ghisi, Enedir

2018-01-15

The objective of this study is to assess the environmental benefit of using rainwater, greywater, water-efficient appliances and their combinations in low-income houses. The study was conducted surveying twenty households located in southern Brazil, which resulted in water end-uses estimation. Then, embodied energy, potential for potable water savings and sewage reduction when using the different strategies were estimated. The environmental benefit analysis of these strategies was performed using an indicator that includes embodied energy, potable water savings, reduction of sewage and energy consumption in the water utility, and sewage production during the life cycle of the system. The results indicated that the strategy with the greatest environmental benefit is the use of water-efficient appliances, which resulted in substantial water savings and reduction of sewage, causing low environmental impact due to lower embodied energy over the life cycle. Copyright © 2017 Elsevier Ltd. All rights reserved.

Reduction of peak energy demand based on smart appliances energy consumption adjustment

NASA Astrophysics Data System (ADS)

Powroźnik, P.; Szulim, R.

2017-08-01

In the paper the concept of elastic model of energy management for smart grid and micro smart grid is presented. For the proposed model a method for reducing peak demand in micro smart grid has been defined. The idea of peak demand reduction in elastic model of energy management is to introduce a balance between demand and supply of current power for the given Micro Smart Grid in the given moment. The results of the simulations studies were presented. They were carried out on real household data available on UCI Machine Learning Repository. The results may have practical application in the smart grid networks, where there is a need for smart appliances energy consumption adjustment. The article presents a proposal to implement the elastic model of energy management as the cloud computing solution. This approach of peak demand reduction might have application particularly in a large smart grid.

Energy efficiency system development

NASA Astrophysics Data System (ADS)

Leman, A. M.; Rahman, K. A.; Chong, Haw Jie; Salleh, Mohd Najib Mohd; Yusof, M. Z. M.

2017-09-01

By subjecting to the massive usage of electrical energy in Malaysia, energy efficiency is now one of the key areas of focus in climate change mitigation. This paper focuses on the development of an energy efficiency system of household electrical appliances for residential areas. Distribution of Questionnaires and pay a visit to few selected residential areas are conducted during the fulfilment of the project as well as some advice on how to save energy are shared with the participants. Based on the collected data, the system developed by the UTHM Energy Team is then evaluated from the aspect of the consumers' behaviour in using electrical appliances and the potential reduction targeted by the team. By the end of the project, 60% of the participants had successfully reduced the electrical power consumption set by the UTHM Energy Team. The reasons for whether the success and the failure is further analysed in this project.

How Does EIA Estimate Energy Consumption and End Uses in U.S. Homes?

EIA Publications

2011-01-01

The Energy Information Administration (EIA) administers the Residential Energy Consumption Survey (RECS) to a nationally representative sample of housing units. Specially trained interviewers collect energy characteristics on the housing unit, usage patterns, and household demographics. This information is combined with data from energy suppliers to these homes to estimate energy costs and usage for heating, cooling, appliances and other end uses information critical to meeting future energy demand and improving efficiency and building design.

Product carbon footprint assessment supporting the green supply chain construction in household appliance manufacturers

NASA Astrophysics Data System (ADS)

Chen, Jianhua; Sun, Liang; Guo, Huiting

2017-11-01

Supply chain carbon emission is one of the factors considered in the green supply chain management. A method was designed to support the green supply chain measures based on the carbon footprint assessment for products. A research for 3 typical household appliances carbon footprint assessment was conducted to explore using product carbon footprint assessment method to guide the green supply chain management of the manufacturers. The result could reflect the differences directions on green supply chain management of manufacturers of washing machine, air conditioner and microwave, respectively That is, the washing machine manufacturer should pay attention to the low carbon activities in upstream suppliers in highest priority, and also the promotion of product energy efficiency. The air conditioner manufacturer should pay attention to the product energy efficiency increasing in highest priority, and the improvement of refrigerant to decrease its GWP. And the microwave manufacture could only focus on the energy efficiency increasing because it contributes most of the carbon emission to its carbon footprint. Besides, the representativeness of product and the applicability of the method were also discussed. As the manufacturer could master the technical information on raw material and components of its products to conduct the product carbon footprint assessment, this method could help the manufacturer to identify the effective green supply chain measures in the preliminary stage.

Energy in the Developing World

NASA Astrophysics Data System (ADS)

Gadgil, Ashok; Fridley, David; Zheng, Nina; Sosler, Andree; Kirchstetter, Thomas; Phadke, Amol

2011-11-01

The five billion persons at the lower economic levels are not only poor, but commonly use technologies that are less efficient and more polluting, wasting their money, hurting their health, polluting their cites, and increasing carbon dioxide in the atmosphere. Many first-world researchers, including the authors, are seeking to help these persons achieve a better life by collaborating on need-driven solutions to energy problems. Here we examine three specific examples of solutions to energy problems, and mitigation strategies in the developing world: (1) Energy Efficiency Standards and Labeling in China. Between 1990 and 2025, China will add 675 million new urban residents, all of whom expect housing, electricity, water, transportation, and other energy services. Policies and institutions must be rapidly set up to manage the anticipated rapid rise in household and commercial energy consumption. This process has progressed from legislating, and setting up oversight of minimum energy performance standards in 1989 (now on 30 products) to voluntary efficiency labels in 1999 (now on 40 products) and to mandatory energy labels in 2005 (now on 21 products). The savings from just the standards and labels in place by 2007 would result in cumulative savings of 1188 teraWatt—hours (TWh) between 2000-2020. By 2020, China would save 110 TWh/yr, or the equivalent of 12 gigaWatts (GW) of power operating continuously. (2) Fuel-efficient biomass cookstoves to reduce energy consumption and reduce pollution. Compared to traditional cooking methods in Darfur, the BDS cooks faster, reduces fuel requirement, and emits less carbon monoxide air pollution. A 2010 survey of 100 households showed that users reduced spending on fuelwood in North Darfur camps from 1/2 of household non-fuelwood budget to less than 1/4 of that budget. The survey showed that each 20 stove puts 330/year in the pocket of the women using the stove, worth 1600 over the stove-life of 5 years. Per capita income of these households is about 300/year. (3) Super Efficient Appliance Deployment. Global domestic electricity consumption is expected to double in 25 years, from 5,700 TWh/yr in 2005 to 11,500 TWh/yr in 2030. The four appliances using largest shares of domestic electricity (lighting, refrigeration, air-conditioning, television) would use some 5,000 TWh/yr in 2030, or 43% of the total, in the baseline scenario. More than 50% of this consumption will be in China, India, European Union and US. We outline efforts to save up to 1.5 gigatons of carbon dioxide emissions per year in 2030 by helping deploy the most efficient commercially available technologies in these four categories. Furthermore, if this effort is extended to twenty-four categories of appliances and equipment, the projected savings in CO2 emissions increase to 6.7 gigatons per year by 2030.

Household and Living Arrangement Projections at the Subnational Level: An Extended Cohort-Component Approach

PubMed Central

Zeng, Yi; Land, Kenneth C.; Wang, Zhenglian; Gu, Danan

2012-01-01

This article presents the core methodological ideas, empirical assessments, and applications of an extended cohort-component approach (known as the “ProFamy model”) to simultaneously project household composition, living arrangements, and population sizes at the subnational level in the United States. Comparisons of projections from 1990 to 2000 using this approach with census counts in 2000 for each of the 50 states and Washington, DC show that 68.0 %, 17.0 %, 11.2 %, and 3.8 % of the absolute percentage errors are <3.0 %, 3.0 % to 4.99 %, 5.0 % to 9.99 %, and ≥10.0 %, respectively. Another analysis compares average forecast errors between the extended cohort-component approach and the still widely used classic headship-rate method, by projecting number-of-bedrooms–specific housing demands from 1990 to 2000 and then comparing those projections with census counts in 2000 for each of the 50 states and Washington, DC. The results demonstrate that, compared with the extended cohort-component approach, the headship-rate method produces substantially more serious forecast errors because it cannot project households by size while the extended cohort-component approach projects detailed household sizes. We also present illustrative household and living arrangement projections for the five decades from 2000 to 2050, with medium-, small-, and large-family scenarios for each of the 50 states; Washington, DC; six counties of southern California, and the Minneapolis–St. Paul metropolitan area. Among many interesting numerical outcomes of household and living arrangement projections with medium, low, and high bounds, the aging of American households over the next few decades across all states/areas is particularly striking. Finally, the limitations of the present study and potential future lines of research are discussed. PMID:23208782

Insights from Smart Meters: Identifying Specific Actions, Behaviors, and Characteristics That Drive Savings in Behavior-Based Programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Todd, A.; Perry, M.; Smith, B.

2014-12-01

In this report, we use smart meter data to analyze specific actions, behaviors, and characteristics that drive energy savings in a BB program. Specifically, we examine a Home Energy Report (HER) program. These programs typically obtain 1% to 3% annual savings, and recent studies have shown hourly savings of between 0.5% and 3%.1 But what is driving these savings? What types of households tend to be “high-savers,” and what behaviors are they adopting? There are several possibilities: one-time behaviors (e.g., changing thermostat settings), reoccurring habitual behaviors (e.g., turning off lights), and equipment purchase behaviors (e.g., energy efficient appliances); these maymore » vary across households, regions, and over time.« less

Insights from Smart Meters. Identifying Specific Actions, Behaviors and Characteristics that drive savings in Behavior-Based Programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Todd, Annika; Perry, Michael; Smith, Brian

2014-12-01

In this report, we use smart meter data to analyze specific actions, behaviors, and characteristics that drive energy savings in a behavior-based (BB) program. Specifically, we examine a Home Energy Report (HER) program. These programs typically obtain 1% to 3% annual savings, and recent studies have shown hourly savings of between 0.5% and 3%. But what is driving these savings? What types of households tend to be “high-savers”, and what behaviors are they adopting? There are several possibilities: one-time behaviors (e.g., changing thermostat settings); reoccurring habitual behaviors (e.g., turning off lights); and equipment purchase behaviors (e.g., energy efficient appliances), andmore » these may vary across households, regions, and over time.« less

Effects of external electrical and magnetic fields on pacemakers and defibrillators: from engineering principles to clinical practice.

PubMed

Beinart, Roy; Nazarian, Saman

2013-12-24

The overall risk of clinically significant adverse events related to EMI in recipients of CIEDs is very low. Therefore, no special precautions are needed when household appliances are used. Environmental and industrial sources of EMI are relatively safe when the exposure time is limited and distance from the CIEDs is maximized. The risk of EMI-induced events is highest within the hospital environment. Physician awareness of the possible interactions and methods to minimize them is warranted.

Building America Case Study: Pilot Demonstration of Phased Energy Efficiency Retrofits: Shallow Retrofit Results, Central and South Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

2017-02-22

The Florida Solar Energy Center (FSEC), in collaboration with Florida Power & Light (FPL), is pursuing a phased residential energy-efficiency retrofit program in Florida. Researchers are looking to establish the impacts of technologies of two retrofit packages -- shallow and deep -- on annual energy and peak energy reductions. Sixty homes have been instrumented to record total house power and detailed energy end-use data on all appliances as well as household interior temperature and relative humidity conditions.

Building America Case Study: Pilot Demonstration of Phased Energy Efficiency Retrofits: Shallow Retrofit Results, Central and South Florida

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. Parker, K. Sutherland, D. Chasar, J. Montemurno, B. Amos, J. Kono

2017-02-01

The Florida Solar Energy Center (FSEC), in collaboration with Florida Power & Light (FPL), is pursuing a phased residential energy-efficiency retrofit program in Florida. Researchers are looking to establish the impacts of technologies of two retrofit packages -- shallow and deep -- on annual energy and peak energy reductions. Sixty homes have been instrumented to record total house power and detailed energy end-use data on all appliances as well as household interior temperature and relative humidity conditions.

Letters to the Editor

NASA Astrophysics Data System (ADS)

1998-03-01

All the Letters to the Editor in this issue are in the same PostScript or PDF file. Contents Comment on `Magnetic and electric field strengths of high voltage power lines and household appliances' José Luis Giordano Dept. de Ciencia y Tecnología de Materiales y Fluidos, CPSI, Universidad de Zaragoza, Spain Twins paradox S R Carson Norton College, Malton, North Yorkshire, UK On alternative ways of finding the ratio of specific heats of gases Tomas Ficker Physics Department, Technical University of Brno, Czech Republic

Management and design of long-life systems; Proceedings of the Symposium, Denver, Colo., April 24-26, 1973

NASA Technical Reports Server (NTRS)

Schurmeier, H. M.

1974-01-01

The long life of Pioneer interplanetary spacecraft is considered along with a general accelerated methodology for long-life mechanical components, dependable long-lived household appliances, and the design and development philosophy to achieve reliability and long life in large turbine generators. Other topics discussed include an integrated management approach to long life in space, artificial heart reliability factors, and architectural concepts and redundancy techniques in fault-tolerant computers. Individual items are announced in this issue.

2016 America's Recycle Day

NASA Image and Video Library

2016-11-15

Members of the Sustainability team at NASA's Kennedy Space Center in Florida look over appliances donated for reuse or recycling in conjunction with America Recycles Day. America Recycles Day is a nationally recognized initiative dedicated to promoting recycling in the United States. Kennedy partnered with several organizations in order to donate as many of the items as possible to those who could use them the most in the Space Coast community. Space center personnel brought in electronic waste, gently used household goods, clothing and more.

A Time-Series Water Level Forecasting Model Based on Imputation and Variable Selection Method.

PubMed

Yang, Jun-He; Cheng, Ching-Hsue; Chan, Chia-Pan

2017-01-01

Reservoirs are important for households and impact the national economy. This paper proposed a time-series forecasting model based on estimating a missing value followed by variable selection to forecast the reservoir's water level. This study collected data from the Taiwan Shimen Reservoir as well as daily atmospheric data from 2008 to 2015. The two datasets are concatenated into an integrated dataset based on ordering of the data as a research dataset. The proposed time-series forecasting model summarily has three foci. First, this study uses five imputation methods to directly delete the missing value. Second, we identified the key variable via factor analysis and then deleted the unimportant variables sequentially via the variable selection method. Finally, the proposed model uses a Random Forest to build the forecasting model of the reservoir's water level. This was done to compare with the listing method under the forecasting error. These experimental results indicate that the Random Forest forecasting model when applied to variable selection with full variables has better forecasting performance than the listing model. In addition, this experiment shows that the proposed variable selection can help determine five forecast methods used here to improve the forecasting capability.

Short-term Power Load Forecasting Based on Balanced KNN

NASA Astrophysics Data System (ADS)

Lv, Xianlong; Cheng, Xingong; YanShuang; Tang, Yan-mei

2018-03-01

To improve the accuracy of load forecasting, a short-term load forecasting model based on balanced KNN algorithm is proposed; According to the load characteristics, the historical data of massive power load are divided into scenes by the K-means algorithm; In view of unbalanced load scenes, the balanced KNN algorithm is proposed to classify the scene accurately; The local weighted linear regression algorithm is used to fitting and predict the load; Adopting the Apache Hadoop programming framework of cloud computing, the proposed algorithm model is parallelized and improved to enhance its ability of dealing with massive and high-dimension data. The analysis of the household electricity consumption data for a residential district is done by 23-nodes cloud computing cluster, and experimental results show that the load forecasting accuracy and execution time by the proposed model are the better than those of traditional forecasting algorithm.

Measurement and human exposure assessment of brominated flame retardants in household products from South China.

PubMed

Chen, She-Jun; Ma, Yun-Juan; Wang, Jing; Tian, Mi; Luo, Xiao-Jun; Chen, Da; Mai, Bi-Xian

2010-04-15

Brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), and decabromodiphenyl ethane (DBDPE) were examined in household products in the Pearl River Delta, South China, including electronic appliances, furniture and upholstery, car interiors, and raw materials for electronics. The concentrations of PBDEs derived from penta-BDE mixture were much lower (<111 ng/g) than those for octa- and deca-BDE commercially derived PBDEs, with maximum values of 15,107 and 1,603,343 ng/g, respectively, in all the household products. Our findings suggest the recycling of old electronic products and their reuse might be also a potential important source of discontinued PBDEs to the environment. DBDPE was found in 20.0% of all the samples, ranging from 311 to 268,230 ng/g. PBDE congener profiles in both the household products and raw materials suggest that some less brominated BDEs in the environment may be derived from the decomposition of higher brominated PBDEs in PBDE-containing products in process of the manufacturing, use and/or recycling. Human exposure to PBDEs from household products via inhalation ranged from 175 to 612 pg/kg bw day, accounting for a small proportion of the total daily exposure via indoor inhalation. Despite the low deleterious risk associated with household products with regard to PBDEs, they are of special concern because of the relatively higher exposures observed for young children and further work is required. 2009 Elsevier B.V. All rights reserved.

Forecasting United States heartworm Dirofilaria immitis prevalence in dogs.

PubMed

Bowman, Dwight D; Liu, Yan; McMahan, Christopher S; Nordone, Shila K; Yabsley, Michael J; Lund, Robert B

2016-10-10

This paper forecasts next year's canine heartworm prevalence in the United States from 16 climate, geographic and societal factors. The forecast's construction and an assessment of its performance are described. The forecast is based on a spatial-temporal conditional autoregressive model fitted to over 31 million antigen heartworm tests conducted in the 48 contiguous United States during 2011-2015. The forecast uses county-level data on 16 predictive factors, including temperature, precipitation, median household income, local forest and surface water coverage, and presence/absence of eight mosquito species. Non-static factors are extrapolated into the forthcoming year with various statistical methods. The fitted model and factor extrapolations are used to estimate next year's regional prevalence. The correlation between the observed and model-estimated county-by-county heartworm prevalence for the 5-year period 2011-2015 is 0.727, demonstrating reasonable model accuracy. The correlation between 2015 observed and forecasted county-by-county heartworm prevalence is 0.940, demonstrating significant skill and showing that heartworm prevalence can be forecasted reasonably accurately. The forecast presented herein can a priori alert veterinarians to areas expected to see higher than normal heartworm activity. The proposed methods may prove useful for forecasting other diseases.

Residential energy consumption and conservation programs: A systematic approach to identify inefficient households, provide meaningful feedback, and prioritize homes for conservation intervention

NASA Astrophysics Data System (ADS)

Macsleyne, Amelia Chadbourne Carus

There are three main objectives for residential energy conservation policies: to reduce the use of fossil fuels, reduce greenhouse gas emissions, and reduce the energy costs seen by the consumer (U.S. Department of Energy: Strategic Objectives, 2006). A prominent difficulty currently facing conservation policy makers and program managers is how to identify and communicate with households that would be good candidates for conservation intervention, in such a way that affects a change in consumption patterns and is cost-effective. This research addresses this issue by separating the problem into three components: how to identify houses that are significantly more inefficient than comparable households; how to find the maximum financially-feasible investment in energy efficiency for a household in order to reduce annual energy costs and/or improve indoor comfort; and how to prioritize low-income households for a subsidized weatherization program. Each component of the problem is presented as a paper prepared for publication. Household consumption related to physical house efficiency, thermostat settings, and daily appliance usage is studied in the first and second paper by analyzing natural gas utility meter readings associated with over 10,000 households from 2001-2006. A rich description of a house's architectural characteristics and household demographics is attained by integrating publicly available databases based on the house address. This combination of information allows for the largest number of individual households studied at this level of detail to date. The third paper uses conservation program data from two natural gas utilities that administer and sponsor the program; over 1,000 weatherized households are included in this sample. This research focuses on natural gas-related household conservation. However, the same principles and methods could be applied for electricity-related conservation programs. We find positive policy implications from each of these three papers.

Using choice architecture to exploit a university Distinct Urban Mine.

PubMed

Pierron, Xavier; Williams, Ian D; Shaw, Peter J; Cleaver, Victoria

2017-10-01

There are widespread concerns regarding the potential future scarcity of ferrous and non-ferrous materials. However, there are already potentially rich reserves of secondary materials via high ownership of Electrical and Electronic Equipment (EEE) in economically-developed nations. Young people are particularly high consumers of EEE, thus university students and campuses may present an opportunity to harness this potential. University Distinct Urban Mines (DUM) may be used to exemplify how potential reserves of secondary metals may be exploited, and could contribute to the transition from a linear to a circular economy. This study aimed to evaluate small household appliances (SHA) DUM from a UK university, with the objectives to identify and quantify student households' SHA ownership, WEEE recycling, stockpiling and discarding habits amongst student households, assess and evaluate the monetary potential of SHA DUM at UK level, and propose methods to exploit DUM for universities in the UK. To this purpose, a quantitative survey was undertaken to measure students' ownership and discarding behaviour with respect to SHA. The amounts of ferrous and non-ferrous materials were then estimated and converted to monetary values from secondary materials market data to appraise the SHA DUM overall value. Thirty-five per cent of SHA are discarded in the general refuse. Broken personal care appliances (PCA) tend to be discarded due to hygiene and small size factors. When in working order, SHA tend to be equally reused, recycled or stockpiled. We conclude that a total of 189 tonnes of ferrous and non-ferrous materials were available via discarding or being stockpiled at the University of Southampton. Extrapolated to UK higher education level, discarded and stockpiled SHA represent a potential worth ∼USD 11 million. To initiate DUM exploitation within Higher Education campuses, we suggest improving users' choice architecture by providing collection methods specific to broken SHA. Copyright © 2017. Published by Elsevier Ltd.

1988/1989 household travel survey

DOT National Transportation Integrated Search

1989-07-01

The primary objectives of this study were to provide the data: (1) : to update the trip generation rates used in the Maricopa Association of Governments (MAG) travel demand forecasting process, and; (2) to validate the MAG trip distribution model. Th...

The Development of Smart Home System for Controlling and Monitoring Energy Consumption using WebSocket Protocol

NASA Astrophysics Data System (ADS)

Witthayawiroj, Niti; Nilaphruek, Pongpon

2017-03-01

Energy consumption especially electricity is considered one of the most serious problems in households these days. It is because the amount of electricity consumed is more than the amount that people actually need. This means that there is an overusing which resulted from the inconvenience of moving to the switch to turn off the light or any appliances and it is often that closing the light is forgettable, for instance; in addition, there are no tools for monitoring how much energy that is consumed in residents. From this, it can be easily seen that people are having a problem in energy usage monitor and control. There are two main objectives of this study including 1) creating the communication framework among server, clients and devices, and 2) developing the prototype system that try to solve the mentioned problems which gives the user an opportunity to know the amount of electricity they have used in their houses and also the ability to turn appliances on and off through the Internet on smart devices such as smart phones and tablets that support Android platform or any web browser. Raspberry Pi is used as a microcontroller and the data is transferred to the smart device by WebSocket protocol which is strongly recommended for real-time communication. The example features on the device’s screen are user management, controlling and monitoring of appliances. The result expresses that the system is very effective and not difficult to use from users’ satisfaction. However, current sensors may be used for a more accurate electricity measurement and Wi-Fi module for more appliances to calculate its power in the future.

Transparent ultraviolet photovoltaic cells.

PubMed

Yang, Xun; Shan, Chong-Xin; Lu, Ying-Jie; Xie, Xiu-Hua; Li, Bing-Hui; Wang, Shuang-Peng; Jiang, Ming-Ming; Shen, De-Zhen

2016-02-15

Photovoltaic cells have been fabricated from p-GaN/MgO/n-ZnO structures. The photovoltaic cells are transparent to visible light and can transform ultraviolet irradiation into electrical signals. The efficiency of the photovoltaic cells is 0.025% under simulated AM 1.5 illumination conditions, while it can reach 0.46% under UV illumination. By connecting several such photovoltaic cells in a series, light-emitting devices can be lighting. The photovoltaic cells reported in this Letter may promise the applications in glass of buildings to prevent UV irradiation and produce power for household appliances in the future.

[Research of controlling of smart home system based on P300 brain-computer interface].

PubMed

Wang, Jinjia; Yang, Chengjie

2014-08-01

Using electroencephalogram (EEG) signal to control external devices has always been the research focus in the field of brain-computer interface (BCI). This is especially significant for those disabilities who have lost capacity of movements. In this paper, the P300-based BCI and the microcontroller-based wireless radio frequency (RF) technology are utilized to design a smart home control system, which can be used to control household appliances, lighting system, and security devices directly. Experiment results showed that the system was simple, reliable and easy to be populirised.

A forecast of broadcast satellite communications

NASA Technical Reports Server (NTRS)

Martino, J. P.; Lenz, R. C., Jr.

1977-01-01

This paper presents forecasts of likely changes in broadcast satellite technology, the technology of ground terminals, and the technology of terrestrial communications competitive with satellites. The impacts of these changes in technology are then assessed, using a cross-impact model of U.S. domestic telecommunications, to determine the consequences of various possible changes in communications satellite technology. These consequences are discussed in terms of various possible services, for households, businesses, and specialized customers, which might become economically viable as a result of improvements in satellite technology.

Analyzing Residential End-Use Energy Consumption Data to Inform Residential Consumer Decisions and Enable Energy Efficiency Improvements

NASA Astrophysics Data System (ADS)

Carlson, Derrick R.

While renewable energy is in the process of maturing, energy efficiency improvements may provide an opportunity to reduce energy consumption and consequent greenhouse gas emissions to bridge the gap between current emissions and the reductions necessary to prevent serious effects of climate change and will continue to be an integral part of greenhouse gas emissions policy moving forward. Residential energy is a largely untapped source of energy reductions as consumers, who wish to reduce energy consumption for monetary, environmental, and other reasons, face barriers. One such barrier is a lack of knowledge or understanding of how energy is consumed in a home and how to reduce this consumption effectively through behavioral and technological changes. One way to improve understanding of residential energy consumption is through the creation of a model to predict which appliances and electronics will be present and significantly contribute to the electricity consumption of a home on the basis of various characteristics of that home. The basis of this model is publically available survey data from the Residential Energy Consumption Survey (RECS). By predicting how households are likely to consume energy, homeowners, policy makers, and other stakeholders have access to valuable data that enables reductions in energy consumption in the residential sector. This model can be used to select homes that may be ripe for energy reductions and to predict the appliances that are the basis of these potential reductions. This work suggests that most homes in the U.S. have about eight appliances that are responsible for about 80% of the electricity consumption in that home. Characteristics such as census region, floor space, income, and total electricity consumption affect which appliances are likely to be in a home, however the number of appliances is generally around 8. Generally it takes around 4 appliances to reach the 50% threshold and 12 appliances to reach 90% of electricity consumption, which suggests significant diminishing returns for parties interested in monitoring appliance level electricity consumption. Another way to improve understanding of residential energy consumption is through the development of residential use phase energy vectors for use in the Economic Input-Output Life Cycle Assessment (EIO-LCA) model. The EIO-LCA model is a valuable scoping tool to predict the environmental impacts of economic activity. This tool has a gap in its capabilities as residential use phase energy is outside the scope of the model. Adding use phase energy vectors to the EIO-LCA model will improve the modeling, provide a more complete estimation of energy impacts and allow for embedded energy to be compared to use phase energy for the purchase of goods and services in the residential sector. This work adds 21 quads of energy to the residential energy sector for the model and 15 quads of energy for personal transportation. These additions represent one third of the total energy consumption of the United States and a third of the total energy in the EIO-LCA model. This work also demonstrates that for many products such as electronics and household appliances use phase energy demands are much greater than manufacturing energy demands and dominate the life cycles for these products. A final way in which this thesis improves upon the understanding of how use phase energy is consumed in a home is through the exploration of potential energy reductions in a home. This analysis selects products that are used or consumed in a home, and explores the potential for reductions in the embedded manufacturing and use phase energy of that product using EIO-LCA and the energy vectors created in Chapter 3. The results give consumers an understanding of where energy is consumed in the lifecycle of products that they purchase and provide policy makers with valuable information on how to focus or refocus policies that are aimed and reducing energy in the residential sector. This work finds that a majority of the energy consumed by retail products is consumed in the use phase of electronics and appliances. Consequently the largest potential reductions in residential energy use can be found in the same area. The work also shows that targeting reductions in the manufacturing energy for many products is likely to be an ineffective strategy for energy reductions with the exception of a select few products. Supply chain energy reductions may be more promising than manufacturing energy reductions, though neither is likely to be as effective as strategies that target use phase energy reductions.

Forecasting of municipal solid waste quantity in a developing country using multivariate grey models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Intharathirat, Rotchana, E-mail: rotchana.in@gmail.com; Abdul Salam, P., E-mail: salam@ait.ac.th; Kumar, S., E-mail: kumar@ait.ac.th

Highlights: • Grey model can be used to forecast MSW quantity accurately with the limited data. • Prediction interval overcomes the uncertainty of MSW forecast effectively. • A multivariate model gives accuracy associated with factors affecting MSW quantity. • Population, urbanization, employment and household size play role for MSW quantity. - Abstract: In order to plan, manage and use municipal solid waste (MSW) in a sustainable way, accurate forecasting of MSW generation and composition plays a key role. It is difficult to carry out the reliable estimates using the existing models due to the limited data available in the developingmore » countries. This study aims to forecast MSW collected in Thailand with prediction interval in long term period by using the optimized multivariate grey model which is the mathematical approach. For multivariate models, the representative factors of residential and commercial sectors affecting waste collected are identified, classified and quantified based on statistics and mathematics of grey system theory. Results show that GMC (1, 5), the grey model with convolution integral, is the most accurate with the least error of 1.16% MAPE. MSW collected would increase 1.40% per year from 43,435–44,994 tonnes per day in 2013 to 55,177–56,735 tonnes per day in 2030. This model also illustrates that population density is the most important factor affecting MSW collected, followed by urbanization, proportion employment and household size, respectively. These mean that the representative factors of commercial sector may affect more MSW collected than that of residential sector. Results can help decision makers to develop the measures and policies of waste management in long term period.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klug, Victoria; Lobscheid, Agnes; Singer, Brett

Cooking of food and use of natural gas cooking burners generate pollutants that can have substantial impacts on residential indoor air quality. The extent of these impacts depends on cooking frequency, duration and specific food preparation activities in addition to the extent to which exhaust fans or other ventilation measures (e.g. windows) are used during cooking. With the intent of improving our understanding of indoor air quality impacts of cooking-related pollutants, we created, posted and advertised a web-based survey about cooking activities in residences. The survey included questions similar to those in California's Residential Appliance Saturation Survey (RASS), relating tomore » home, household and cooking appliance characteristics and weekly patterns of meals cooked. Other questions targeted the following information not captured in the RASS: (1) oven vs. cooktop use, the number of cooktop burners used and the duration of burner use when cooking occurs, (2) specific cooking activities, (3) the use of range hood or window to increase ventilation during cooking, and (4) occupancy during cooking. Specific cooking activity questions were asked about the prior 24 hours with the assumption that most people are able to recollect activities over this time period. We examined inter-relationships among cooking activities and patterns and relationships of cooking activities to household demographics. We did not seek to obtain a sample of respondents that is demographically representative of the California population but rather to inexpensively gather information from homes spanning ranges of relevant characteristics including the number of residents and presence or absence of children. This report presents the survey, the responses obtained, and limited analysis of the results.« less

Residential energy demand models: Current status and future improvements

NASA Astrophysics Data System (ADS)

Peabody, G.

1980-12-01

Two models currently used to analyze energy use by the residential sector are described. The ORNL model is used to forecast energy use by fuel type for various end uses on a yearly basis. The MATH/CHRDS model analyzes variations in energy expenditures by households of various socioeconomic and demographic characteristics. The essential features of the ORNL and MATH/CHRDS models are retained in a proposed model and integrated into a framework that is more flexible than either model. The important determinants of energy use by households are reviewed.

Single phase space laundry development

NASA Technical Reports Server (NTRS)

Colombo, Gerald V.; Putnam, David F.; Lunsford, Teddie D.; Streech, Neil D.; Wheeler, Richard R., Jr.; Reimers, Harold

1993-01-01

This paper describes a newly designed, 2.7 Kg (6 pound) capacity, laundry machine called the Single Phase Laundry (SPSL). The machine was designed to wash and dry crew clothing in a micro-gravity environment. A prototype unit was fabricated for NASA-JSC under a Small Business Innovated Research (SBIR) contract extending from September 1990 to January 1993. The unit employs liquid jet agitation, microwave vacuum drying, and air jet tumbling, which was perfected by KC-135 zero-g flight testing. Operation is completely automated except for loading and unloading clothes. The unit uses about 20 percent less power than a conventional household appliance.

Analysis Software

NASA Technical Reports Server (NTRS)

1994-01-01

General Purpose Boundary Element Solution Technology (GPBEST) software employs the boundary element method of mechanical engineering analysis, as opposed to finite element. It is, according to one of its developers, 10 times faster in data preparation and more accurate than other methods. Its use results in less expensive products because the time between design and manufacturing is shortened. A commercial derivative of a NASA-developed computer code, it is marketed by Best Corporation to solve problems in stress analysis, heat transfer, fluid analysis and yielding and cracking of solids. Other applications include designing tractor and auto parts, household appliances and acoustic analysis.

Programmable valve shunts: are they really better?

PubMed

Kataria, Rashim; Kumar, Vimal; Mehta, Veer Singh

2012-01-01

Programmable valve shunts allows selection of opening pressure of shunt valve. In the presented article, a unique complication pertaining to programmable shunts has been discussed. A 5-year-old boy who had tectal plate low grade glioma with obstructive hydrocephalus was managed with Codman programmable ventriculoperitoneal shunt. There was a spontaneous change in the opening pressure of the shunt valve leading to shunt malfunction. Routinely used household appliances produce a magnetic field strong enough to cause change in the setting of shunt valve pressure and may lead to valve malfunction. Other causes of programmable valve malfunction also discussed.

A Bayesian spatio-temporal model for forecasting Anaplasma species seroprevalence in domestic dogs within the contiguous United States.

PubMed

Liu, Yan; Watson, Stella C; Gettings, Jenna R; Lund, Robert B; Nordone, Shila K; Yabsley, Michael J; McMahan, Christopher S

2017-01-01

This paper forecasts the 2016 canine Anaplasma spp. seroprevalence in the United States from eight climate, geographic and societal factors. The forecast's construction and an assessment of its performance are described. The forecast is based on a spatial-temporal conditional autoregressive model fitted to over 11 million Anaplasma spp. seroprevalence test results for dogs conducted in the 48 contiguous United States during 2011-2015. The forecast uses county-level data on eight predictive factors, including annual temperature, precipitation, relative humidity, county elevation, forestation coverage, surface water coverage, population density and median household income. Non-static factors are extrapolated into the forthcoming year with various statistical methods. The fitted model and factor extrapolations are used to estimate next year's regional prevalence. The correlation between the observed and model-estimated county-by-county Anaplasma spp. seroprevalence for the five-year period 2011-2015 is 0.902, demonstrating reasonable model accuracy. The weighted correlation (accounting for different sample sizes) between 2015 observed and forecasted county-by-county Anaplasma spp. seroprevalence is 0.987, exhibiting that the proposed approach can be used to accurately forecast Anaplasma spp. seroprevalence. The forecast presented herein can a priori alert veterinarians to areas expected to see Anaplasma spp. seroprevalence beyond the accepted endemic range. The proposed methods may prove useful for forecasting other diseases.

Female participation in household decision-making: an analysis of consumer durables' acquisition in Pakistan.

PubMed

Mujahid-mukhtar, E; Mukhtar, H

1991-01-01

Investigating the nature and degree of female household decision-making in Pakistan, this paper analyzes the influence of women in the purchase consumer durables. The paper also identifies those factors which enable women to play a more active role in the decision-making process. Because women in Pakistan are generally excluded from the public sphere, their level of emancipation is better assessed according to the degree of participation in household decision-making. A good measure of women's power within a household is their influence in the purchase of consumer durables (cars, appliances, etc.), whose expense and life-long nature makes their purchase an important decision. For this study, the authors relied on data from a 1989 nationwide household survey conducted by AERC, which included a information concerning the acquisition of 12 consumer durables as expected. As expected, men make more decisions on the purchase of all consumer goods than women, even for items in which women feel more need than men (e.g. sewing machines, washing machines). The study found that for the needs felt by women for all durable goods, men make 2/3 of all decisions, while women make only 1/3 of decisions. And in cases where the need is felt by men, the men make 93% of the decisions, while women decide only 3 % of the times. The study identified various cultural and economic factors that affect women's decision making power: urban women, women in nuclear families, educated women, and working women generally have more decision making power than rural women, women in extended families, illiterate women, and unemployed women.

A Bayesian spatio-temporal model for forecasting Anaplasma species seroprevalence in domestic dogs within the contiguous United States

PubMed Central

Liu, Yan; Watson, Stella C.; Gettings, Jenna R.; Lund, Robert B.; Nordone, Shila K.; McMahan, Christopher S.

2017-01-01

This paper forecasts the 2016 canine Anaplasma spp. seroprevalence in the United States from eight climate, geographic and societal factors. The forecast’s construction and an assessment of its performance are described. The forecast is based on a spatial-temporal conditional autoregressive model fitted to over 11 million Anaplasma spp. seroprevalence test results for dogs conducted in the 48 contiguous United States during 2011–2015. The forecast uses county-level data on eight predictive factors, including annual temperature, precipitation, relative humidity, county elevation, forestation coverage, surface water coverage, population density and median household income. Non-static factors are extrapolated into the forthcoming year with various statistical methods. The fitted model and factor extrapolations are used to estimate next year’s regional prevalence. The correlation between the observed and model-estimated county-by-county Anaplasma spp. seroprevalence for the five-year period 2011–2015 is 0.902, demonstrating reasonable model accuracy. The weighted correlation (accounting for different sample sizes) between 2015 observed and forecasted county-by-county Anaplasma spp. seroprevalence is 0.987, exhibiting that the proposed approach can be used to accurately forecast Anaplasma spp. seroprevalence. The forecast presented herein can a priori alert veterinarians to areas expected to see Anaplasma spp. seroprevalence beyond the accepted endemic range. The proposed methods may prove useful for forecasting other diseases. PMID:28738085

Value of the GENS Forecast Ensemble as a Tool for Adaptation of Economic Activity to Climate Change

NASA Astrophysics Data System (ADS)

Hancock, L. O.; Alpert, J. C.; Kordzakhia, M.

2009-12-01

In an atmosphere of uncertainty as to the magnitude and direction of climate change in upcoming decades, one adaptation mechanism has emerged with consensus support: the upgrade and dissemination of spatially-resolved, accurate forecasts tailored to the needs of users. Forecasting can facilitate the changeover from dependence on climatology that is increasingly out of date. The best forecasters are local, but local forecasters face great constraints in some countries. Indeed, it is no coincidence that some areas subject to great weather variability and strong processes of climate change are economically vulnerable: mountainous regions, for example, where heavy and erratic flooding can destroy the value built up by households over years. It follows that those best placed to benefit from forecasting upgrades may not be those who have invested in the greatest capacity to date. More-flexible use of the global forecasts may contribute to adaptation. NOAA anticipated several years ago that their forecasts could be used in new ways in the future, and accordingly prepared sockets for easy access to their archives. These could be used to empower various national and regional capacities. Verification to identify practical lead times for the economically important variables is a needed first step. This presentation presents the verification that our team has undertaken, a pilot effort in which we considered variables of interest to economic actors in several lower income countries, cf. shepherds in a remote area of Central Asia, and verified the ensemble forecasts of those variables.

Fundamentals of electric power conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umans, S.D.

1992-12-01

Its rugged nature and straightforward design make the induction motor the most commonly used type of electric motor. This motor ranges in size from the fractional-horsepower, single-phase motors found in household appliances to polyphase motors rated at thousands of horsepower for industrial applications. Volume 1 of this report describes the function of induction motors, their characteristics, and induction motor testing. Volume 2 describes the characteristics of high-efficiency induction motors, with emphasis on the techniques used to obtain high efficiency. This two-volume report is written in nontechnical language and is intended for readers who require background from an applications, marketing, motormore » planning, or managerial perspective.« less

Fundamentals of electric power conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umans, S.D.

1992-12-01

Its rugged nature and straightforward design make the induction motor the most commonly used type of electric motor. This motor ranges in size fro the fractional-horsepower, single-phase motors found in household appliances to polyphase motors rated at thousands of horsepower for industrial applications. Volume 1 of this report describes the function of induction motors, their characteristics, and induction motor testing. Volume 2 describes the characteristics of high-efficiency induction motors, with emphasis on the techniques used to obtain high efficiency. This two-volume report is written in nontechnical language and is intended for readers who require background from applications, marketing, motor planning,more » or managerial perspective.« less

Research, Development and Demonstration of Micro-CHP Systems for Residential Applications - Phase I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robert A. Zogg

The objective of the Micro-CHP Phase I effort was to develop a conceptual design for a Micro-CHP system including: Defining market potential; Assessing proposed technology; Developing a proof-of-principle design; and Developing a commercialization strategy. TIAX LLC assembled a team to develop a Micro-CHP system that will provide electricity and heating. TIAX, the contractor and major cost-share provider, provided proven expertise in project management, prime-mover design and development, appliance development and commercialization, analysis of residential energy loads, technology assessment, and market analysis. Kohler Company, the manufacturing partner, is a highly regarded manufacturer of standby power systems and other residential products. Kohlermore » provides a compellingly strong brand, along with the capabilities in product development, design, manufacture, distribution, sales, support, service, and marketing that only a manufacturer of Kohler's status can provide. GAMA, an association of appliance and equipment manufacturers, provided a critical understanding of appliance commercialization issues, including regulatory requirements, large-scale market acceptance issues, and commercialization strategies. The Propane Education & Research Council, a cost-share partner, provided cost share and aided in ensuring the fuel flexibility of the conceptual design. Micro-CHP systems being commercialized in Europe and Japan are generally designed to follow the household thermal load, and generate electricity opportunistically. In many cases, any excess electricity can be sold back to the grid (net metering). These products, however, are unlikely to meet the demands of the U.S. market. First, these products generally cannot provide emergency power when grid power is lost--a critical feature to market success in the U.S. Even those that can may have insufficient electric generation capacities to meet emergency needs for many U.S. homes. Second, the extent to which net metering will be available in the U.S. is unclear. Third, these products are typically not designed for use in households having forced hot-air heating, which is the dominant heating system in the U.S. The U.S. market will also require a major manufacturer that has the reputation and brand recognition, low-cost manufacturing capability, distribution, sales, and service infrastructure, and marketing power to achieve significant market size with a previously unknown and unproven product. History has proven time and time again that small-to-medium-size manufacturers do not have the resources and capabilities to achieve significant markets with such products. During the Phase I effort, the Team developed a conceptual design for a Micro-CHP system that addresses key DOE and U.S. market needs: (1) Provides emergency power adequate for critical household loads, with none of the key drawbacks associated with typical, low-cost emergency generators, such as liquid fuel storage, inability to power ''hard-wired'' loads, need to run temporary extension cords for plug loads, manual set up required, susceptibility to overload, and risk of failure due to lack of maintenance and infrequent operation; (2) Requires no special skills to install--plumbers, electricians and HVAC technicians will typically have all necessary skills; (3) Can be used with the major residential fuels in the U.S., including natural gas and propane, and can be easily adapted to fuel oil as well as emerging fuels as they become available; and (4) Significantly reduces household energy consumption and energy costs.« less

Forecasting generation of urban solid waste in developing countries--a case study in Mexico.

PubMed

Buenrostro, O; Bocco, G; Vence, J

2001-01-01

Based on a study of the composition of urban solid waste (USW) and of socioeconomic variables in Morelia, Mexico, generation rates were estimated. In addition, the generation of residential solid waste (RSW) and nonresidential solid waste (NRSW) was forecasted by means of a multiple linear regression (MLR) analysis. For residential sources, the independent variables analyzed were monthly wages, persons per dwelling, age, and educational level of the heads of the household. For nonresidential sources, variables analyzed were number of employees, area of facilities, number of working days, and working hours per day. The forecasted values for residential waste were similar to those observed. This approach may be applied to areas in which available data are scarce, and in which there is an urgent need for the planning of adequate management of USW.

Nonprice incentives and energy conservation

PubMed Central

Asensio, Omar I.; Delmas, Magali A.

2015-01-01

In the electricity sector, energy conservation through technological and behavioral change is estimated to have a savings potential of 123 million metric tons of carbon per year, which represents 20% of US household direct emissions in the United States. In this article, we investigate the effectiveness of nonprice information strategies to motivate conservation behavior. We introduce environment and health-based messaging as a behavioral strategy to reduce energy use in the home and promote energy conservation. In a randomized controlled trial with real-time appliance-level energy metering, we find that environment and health-based information strategies, which communicate the environmental and public health externalities of electricity production, such as pounds of pollutants, childhood asthma, and cancer, outperform monetary savings information to drive behavioral change in the home. Environment and health-based information treatments motivated 8% energy savings versus control and were particularly effective on families with children, who achieved up to 19% energy savings. Our results are based on a panel of 3.4 million hourly appliance-level kilowatt–hour observations for 118 residences over 8 mo. We discuss the relative impacts of both cost-savings information and environmental health messaging strategies with residential consumers. PMID:25583494

Effect of Printing Parameters on Tensile, Dynamic Mechanical, and Thermoelectric Properties of FDM 3D Printed CABS/ZnO Composites.

PubMed

Aw, Yah Yun; Yeoh, Cheow Keat; Idris, Muhammad Asri; Teh, Pei Leng; Hamzah, Khairul Amali; Sazali, Shulizawati Aqzna

2018-03-22

Fused deposition modelling (FDM) has been widely used in medical appliances, automobile, aircraft and aerospace, household appliances, toys, and many other fields. The ease of processing, low cost and high flexibility of FDM technique are strong advantages compared to other techniques for thermoelectric polymer composite fabrication. This research work focuses on the effect of two crucial printing parameters (infill density and printing pattern) on the tensile, dynamic mechanical, and thermoelectric properties of conductive acrylonitrile butadiene styrene/zinc oxide (CABS/ZnO composites fabricated by FDM technique. Results revealed significant improvement in tensile strength and Young's modulus, with a decrease in elongation at break with infill density. Improvement in dynamic storage modulus was observed when infill density changed from 50% to 100%. However, the loss modulus and damping factor reduced gradually. The increase of thermal conductivity was relatively smaller compared to the improvement of electrical conductivity and Seebeck coefficient, therefore, the calculated figure of merit (ZT) value increased with infill density. Line pattern performed better than rectilinear, especially in tensile properties and electrical conductivity. From the results obtained, FDM-fabricated CABS/ZnO showed much potential as a promising candidate for thermoelectric application .

Nonprice incentives and energy conservation.

PubMed

Asensio, Omar I; Delmas, Magali A

2015-02-10

In the electricity sector, energy conservation through technological and behavioral change is estimated to have a savings potential of 123 million metric tons of carbon per year, which represents 20% of US household direct emissions in the United States. In this article, we investigate the effectiveness of nonprice information strategies to motivate conservation behavior. We introduce environment and health-based messaging as a behavioral strategy to reduce energy use in the home and promote energy conservation. In a randomized controlled trial with real-time appliance-level energy metering, we find that environment and health-based information strategies, which communicate the environmental and public health externalities of electricity production, such as pounds of pollutants, childhood asthma, and cancer, outperform monetary savings information to drive behavioral change in the home. Environment and health-based information treatments motivated 8% energy savings versus control and were particularly effective on families with children, who achieved up to 19% energy savings. Our results are based on a panel of 3.4 million hourly appliance-level kilowatt-hour observations for 118 residences over 8 mo. We discuss the relative impacts of both cost-savings information and environmental health messaging strategies with residential consumers.

Performance benefits of adaptive, multimicrophone, interference-canceling systems in everyday environments

NASA Astrophysics Data System (ADS)

Desloge, Joseph G.; Zimmer, Martin J.; Zurek, Patrick M.

2004-05-01

Adaptive multimicrophone systems are currently used for a variety of noise-cancellation applications (such as hearing aids) to preserve signals arriving from a particular (target) direction while canceling other (jammer) signals in the environment. Although the performance of these systems is known to degrade with increasing reverberation, there are few measurements of adaptive performance in everyday reverberant environments. In this study, adaptive performance was compared to that of a simple, nonadaptive cardioid microphone to determine a measure of adaptive benefit. Both systems used recordings (at an Fs of 22050 Hz) from the same two omnidirectional microphones, which were separated by 1 cm. Four classes of environment were considered: outdoors, household, parking garage, and public establishment. Sources were either environmental noises (e.g., household appliances, restaurant noise) or a controlled noise source. In all situations, no target was present (i.e., all signals were jammers) to obtain maximal jammer cancellation. Adaptive processing was based upon the Griffiths-Jim generalized sidelobe canceller using filter lengths up to 400 points. Average intelligibility-weighted adaptive benefit levels at a source distance of 1 m were, at most, 1.5 dB for public establishments, 2 dB for household rooms and the parking garage, and 3 dB outdoors. [Work supported by NIOSH.

Analysis and forecasting of municipal solid waste in Nankana City using geo-spatial techniques.

PubMed

Mahmood, Shakeel; Sharif, Faiza; Rahman, Atta-Ur; Khan, Amin U

2018-04-11

The objective of this study was to analyze and forecast municipal solid waste (MSW) in Nankana City (NC), District Nankana, Province of Punjab, Pakistan. The study is based on primary data acquired through a questionnaire, Global Positioning System (GPS), and direct waste sampling and analysis. Inverse distance weighting (IDW) technique was applied to geo-visualize the spatial trend of MSW generation. Analysis revealed that the total MSW generated was 12,419,636 kg/annum (12,419.64 t) or 34,026.4 kg/day (34.03 t), or 0.46 kg/capita/day (kg/cap/day). The average wastes generated per day by studied households, clinics, hospitals, and hotels were 3, 7.5, 20, and 15 kg, respectively. The residential sector was the top producer with 95.5% (32,511 kg/day) followed by commercial sector 1.9% (665 kg/day). On average, high-income and low-income households were generating waste of 4.2 kg/household/day (kg/hh/day) and 1.7 kg/hh/day, respectively. Similarly, large-size families were generating more (4.4 kg/hh/day) waste than small-size families (1.8 kg/hh/day). The physical constituents of MSW generated in the study area with a population of about 70,000 included paper (7%); compostable matter (61%); plastics (9%); fine earth, ashes, ceramics, and stones (20.4%); and others (2.6%).The spatial trend of MSW generation varies; city center has a high rate of generation and towards periphery generation lowers. Based on the current population growth and MSW generation rate, NC is expected to generate 2.8 times more waste by the year 2050.This is imperative to develop a proper solid waste management plan to reduce the risk of environmental degradation and protect human health. This study provides insights into MSW generation rate, physical composition, and forecasting which are vital in its management strategies.

Evaluating the potential of improving residential water balance at building scale.

PubMed

Agudelo-Vera, Claudia M; Keesman, Karel J; Mels, Adriaan R; Rijnaarts, Huub H M

2013-12-15

Earlier results indicated that, for an average household, self-sufficiency in water supply can be achieved by following the Urban harvest Approach (UHA), in a combination of demand minimization, cascading and multi-sourcing. To achieve these results, it was assumed that all available local resources can be harvested. In reality, however, temporal, spatial and location-bound factors pose limitations to this harvest and, thus, to self-sufficiency. This article investigates potential spatial and temporal limitations to harvest local water resources at building level for the Netherlands, with a focus on indoor demand. Two building types were studied, a free standing house (one four-people household) and a mid-rise apartment flat (28 two-person households). To be able to model yearly water balances, daily patterns considering household occupancy and presence of water using appliances were defined per building type. Three strategies were defined. The strategies include demand minimization, light grey water (LGW) recycling, and rainwater harvesting (multi-sourcing). Recycling and multi-sourcing cater for toilet flushing and laundry machine. Results showed that water saving devices may reduce 30% of the conventional demand. Recycling of LGW can supply 100% of second quality water (DQ2) which represents 36% of the conventional demand or up to 20% of the minimized demand. Rainwater harvesting may supply approximately 80% of the minimized demand in case of the apartment flat and 60% in case of the free standing house. To harvest these potentials, different system specifications, related to the household type, are required. Two constraints to recycle and multi-source were identified, namely i) limitations in the grey water production and available rainfall; and ii) the potential to harvest water as determined by the temporal pattern in water availability, water use, and storage and treatment capacities. Copyright © 2013 Elsevier Ltd. All rights reserved.

Technical support document: Energy conservation standards for consumer products: Dishwashers, clothes washers, and clothes dryers including: Environmental impacts; regulatory impact analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-12-01

The Energy Policy and Conservation Act as amended (P.L. 94-163), establishes energy conservation standards for 12 of the 13 types of consumer products specifically covered by the Act. The legislation requires the Department of Energy (DOE) to consider new or amended standards for these and other types of products at specified times. This Technical Support Document presents the methodology, data and results from the analysis of the energy and economic impacts of standards on dishwashers, clothes washers, and clothes dryers. The economic impact analysis is performed in five major areas: An Engineering Analysis, which establishes technical feasibility and product attributesmore » including costs of design options to improve appliance efficiency. A Consumer Analysis at two levels: national aggregate impacts, and impacts on individuals. The national aggregate impacts include forecasts of appliance sales, efficiencies, energy use, and consumer expenditures. The individual impacts are analyzed by Life-Cycle Cost (LCC), Payback Periods, and Cost of Conserved Energy (CCE), which evaluate the savings in operating expenses relative to increases in purchase price; A Manufacturer Analysis, which provides an estimate of manufacturers' response to the proposed standards. Their response is quantified by changes in several measures of financial performance for a firm. An Industry Impact Analysis shows financial and competitive impacts on the appliance industry. A Utility Analysis that measures the impacts of the altered energy-consumption patterns on electric utilities. A Environmental Effects analysis, which estimates changes in emissions of carbon dioxide, sulfur oxides, and nitrogen oxides, due to reduced energy consumption in the home and at the power plant. A Regulatory Impact Analysis collects the results of all the analyses into the net benefits and costs from a national perspective. 47 figs., 171 tabs. (JF)« less

Reduced-Order Models for Load Management in the Power Grid

NASA Astrophysics Data System (ADS)

Alizadeh, Mahnoosh

In recent years, considerable research efforts have been directed towards designing control schemes that can leverage the inherent flexibility of electricity demand that is not tapped into in today's electricity markets. It is expected that these control schemes will be carried out by for-profit entities referred to as aggregators that operate at the edge of the power grid network. While the aggregator control problem is receiving much attention, more high-level questions of how these aggregators should plan their market participation, interact with the main grid and with each other, remain rather understudied. Answering these questions requires a large-scale model for the aggregate flexibility that can be harnessed from the a population of customers, particularly for residences and small businesses. The contribution of this thesis towards this goal is divided into three parts: In Chapter 3, a reduced-order model for a large population of heterogeneous appliances is provided by clustering load profiles that share similar degrees of freedom together. The use of such reduced-order model for system planning and optimal market decision making requires a foresighted approximation of the number of appliances that will join each cluster. Thus, Chapter 4 provides a systematic framework to generate such forecasts for the case of Electric Vehicles, based on real-world battery charging data. While these two chapters set aside the economic side that is naturally involved with participation in demand response programs and mainly focus on the control problem, Chapter 5 is dedicated to the study of optimal pricing mechanisms in order to recruit heterogeneous customers in a demand response program in which an aggregator can directly manage their appliances' load under their specified preferences. Prices are proportional to the wholesale market savings that can result from each recruitment event.

An experimental study of potential residential and commercial applications of small-scale hybrid power systems

NASA Astrophysics Data System (ADS)

Acosta, Michael Anthony

The research presented in this thesis provides an understanding of small-scale hybrid power systems. Experiments were conducted to identify potential applications of renewable energy in residential and commercial applications in the Rio Grande Valley of Texas. Solar and wind energy converted into electric energy was stored in batteries and inverted to power common household and commercial appliances. Several small to medium size hybrid power systems were setup and utilized to conduct numerous tests to study renewable energy prospects and feasibility for various applications. The experimental results obtained indicate that carefully constructed solar power systems can provide people living in isolated communities with sufficient energy to consistently meet their basic power needs.

Silver in medicine: a brief history BC 335 to present.

PubMed

Barillo, David J; Marx, David E

2014-12-01

Silver is a naturally occurring element. Similar to other metals, the ionized form of silver (Ag(+1)) has known antimicrobial properties. A number of wound dressings incorporating silver ion or silver compounds have recently been developed and marketed. In addition, the antimicrobial effects of silver are currently being promoted in consumer products such as clothing and household appliances. The present use of silver in medical and consumer products has prompted concerns for potential toxicity and ecological effects, including induction of microbial resistance to antibiotics. These concerns ignore the fact that silver has been used for medicinal purposes for several thousand years. A historical review of the uses of silver in medicine is presented.

Sensors Applications, Volume 4, Sensors for Automotive Applications

NASA Astrophysics Data System (ADS)

Marek, Jiri; Trah, Hans-Peter; Suzuki, Yasutoshi; Yokomori, Iwao

2003-07-01

An international team of experts from the leading companies in this field gives a detailed picture of existing as well as future applications. They discuss in detail current technologies, design and construction concepts, market considerations and commercial developments. Topics covered include vehicle safety, fuel consumption, air conditioning, emergency control, traffic control systems, and electronic guidance using radar and video. Meeting the growing need for comprehensive information on the capabilities, potentials and limitations of modern sensor systems, Sensors Applications is a book series covering the use of sophisticated technologies and materials for the creation of advanced sensors and their implementation in the key areas process monitoring, building control, health care, automobiles, aerospace, environmental technology and household appliances.

A health intervention or a kitchen appliance? Household costs and benefits of a cleaner burning biomass-fuelled cookstove in Malawi.

PubMed

Cundale, Katie; Thomas, Ranjeeta; Malava, Jullita Kenala; Havens, Deborah; Mortimer, Kevin; Conteh, Lesong

2017-06-01

Pneumonia is the leading cause of mortality for children under five years in sub-Saharan Africa. Household air pollution has been found to increase risk of pneumonia, especially due to exposure from dirty burning biomass fuels. It has been suggested that advanced stoves, which burn fuel more efficiently and reduce smoke emissions, may help to reduce household air pollution in poor, rural settings. This qualitative study aims to provide an insight into the household costs and perceived benefits from use of the stove in Malawi. It was conducted alongside The Cooking and Pneumonia Study (CAPS), the largest village cluster-level randomised controlled trial of an advanced combustion cookstove intervention to prevent pneumonia in children under five to date. In 2015, using 100 semi-structured interviews this study assessed household time use and perceptions of the stove from both control and intervention participants taking part in the CAPS trial in Chilumba. Household direct and indirect costs associated with the intervention were calculated. Users overwhelming liked using the stove. The main reported benefits were reduced cooking times and reduced fuel consumption. In most interviews, the health benefits were not initially identified as advantages of the stove, although when prompted, respondents stated that reduced smoke emissions contributed to a reduction in respiratory symptoms. The cost of the stove was much higher than most respondents said they would be willing to pay. The stoves were not primarily seen as health products. Perceptions of limited impact on health was subsequently supported by the CAPS trial data which showed no significant effect on pneumonia. While the findings are encouraging from the perspective of acceptability, without innovative financing mechanisms, general uptake and sustained use of the stove may not be possible in this setting. The findings also raise the question of whether the stoves should be marketed and championed as 'health interventions'. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

On the effects of fuel leakage on CO production from household burners as revealed by LIF and CARS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van der Meij, C.E.; Mokhov, A.V.; Jacobs, R.A.A.M.

Measurements of the distributions of CO, OH, and temperature in flames from two commonly used, commercially available household burners are presented. The local mole fractions of CO and relative distribution of OH have been obtained using laser-induced fluorescence, while the local temperatures have, been determined by coherent anti-Stokes Raman scattering (CARS). For both burners, burning in the open air, CO formation outside the main flames has been observed and attributed to the leakage of fuel-air mixture at the edges of the flame, where the fuel is subsequently converted to CO in the boundary layer between the flame and the surroundings.more » For a rich-premixed, multiblade burner, which gives Bunsen-like flames, the CO produced by the leaking fuel appears to be oxidized by OH arising from the outer cones of adjacent flames, and burns out to low concentrations. In the case of a lean-premixed burner, the CO produced by fuel leakage remains in the cool boundary layer without adequate burnout. Possible consequences for appliance behavior are discussed.« less

Numerical analysis of natural ventilation system in a studio apartment in Bangladesh

NASA Astrophysics Data System (ADS)

Kabir, K. M. Ariful; Hasan, Md. Rakibul; Khan, Md. Abdul Hakim

2017-07-01

The study of temperature and air flow for natural ventilation system has been investigated numerically. A finite element model for studio apartment was developed with the aim of achieving detail energy allocation in the real buildings during the transient process in the walls and internal air. A tool of computational fluid dynamics (CFD) is employed to assist the process. In the tropical regions most of the energy is consumed by the heating, cooling and ventilation appliances. Therefore, the optimize ventilation system will be a suitable and valid option for the saving of energy from the household sector to increase cooling performance and ensuring thermal comfort as well. A mathematical exploration is carried out on full scale dwelling and small scale model and indication is given on the relevance of such a comparison. Calculations are carried out with household heat sources for calm and windy period, but without any human. As expected, for windy periods, the wind is the main driving force behind the internal air flow. However, in calm periods for unsteady flow the internal airflow looks like more complexes through observation.

Development and Application of a ZigBee-Based Building Energy Monitoring and Control System

PubMed Central

Peng, Changhai

2014-01-01

Increasing in energy consumption, particularly with the ever-increasing growth and development of urban systems, has become a major concern in most countries. In this paper, the authors propose a cost-effective ZigBee-based building energy monitoring and control system (ZBEMCS), which is composed of a gateway, a base station, and sensors. Specifically, a new hardware platform for power sensor nodes is developed to perform both local/remote power parameter measurement and power on/off switching for electric appliances. The experimental results show that the ZBEMCS can easily monitor energy usage with a high level of accuracy. Two typical applications of ZBEMCS such as subentry metering and household metering of building energy are presented. The former includes lighting socket electricity, HVAC electricity, power electricity and special electricity. The latter includes household metering according to the campus's main function zone and each college or department. Therefore, this system can be used for energy consumption monitoring, long-term energy conservation planning, and the development of automated energy conservation for building applications. PMID:25254249

Development and application of a ZigBee-based building energy monitoring and control system.

PubMed

Peng, Changhai; Qian, Kun

2014-01-01

Increasing in energy consumption, particularly with the ever-increasing growth and development of urban systems, has become a major concern in most countries. In this paper, the authors propose a cost-effective ZigBee-based building energy monitoring and control system (ZBEMCS), which is composed of a gateway, a base station, and sensors. Specifically, a new hardware platform for power sensor nodes is developed to perform both local/remote power parameter measurement and power on/off switching for electric appliances. The experimental results show that the ZBEMCS can easily monitor energy usage with a high level of accuracy. Two typical applications of ZBEMCS such as subentry metering and household metering of building energy are presented. The former includes lighting socket electricity, HVAC electricity, power electricity and special electricity. The latter includes household metering according to the campus's main function zone and each college or department. Therefore, this system can be used for energy consumption monitoring, long-term energy conservation planning, and the development of automated energy conservation for building applications.

Optimal residential water conservation strategies considering related energy in California

NASA Astrophysics Data System (ADS)

Escriva-Bou, Alvar; Lund, Jay R.; Pulido-Velazquez, Manuel

2015-06-01

Although most freshwater resources are used in agriculture, residential water use is a much more energy intensive user. Based on this, we analyze the increased willingness to adopt water conservation strategies if energy cost is included in the customers' utility function. Using a Water-Energy-CO2 emissions model for household water end uses and probability distribution functions for parameters affecting water and water-related energy use in 10 different locations in California, this research introduces a probabilistic two-stage optimization model considering technical and behavioral decision variables to obtain the most economical strategies to minimize household water and water-related energy bills and costs given both water and energy price shocks. Results can provide an upper bound of household savings for customers with well-behaved preferences, and show greater adoption rates to reduce energy intensive appliances when energy is accounted, resulting in an overall 24% reduction in indoor water use that represents a 30% reduction in water-related energy use and a 53% reduction in household water-related CO2 emissions. Previous use patterns and water and energy rate structures can affect greatly the potential benefits for customers and so their behavior. Given that water and energy are somewhat complementary goods for customers, we use results of the optimization to obtain own-price and cross-price elasticities of residential water use by simulating increases in water and energy prices. While the results are highly influenced by assumptions due to lack of empirical data, the method presented has no precedent in the literature and hopefully will stimulate the collection of additional relevant data.

Validity and reliability of the Arabic version of the Household Food Insecurity Access Scale in rural Lebanon.

PubMed

Naja, Farah; Hwalla, Nahla; Fossian, Talar; Zebian, Dina; Nasreddine, Lara

2015-02-01

To assess the validity and reliability of the Arabic version of the Household Food Insecurity Access Scale (HFIAS) in rural Lebanon. A cross-sectional study on a sample of households with at least one child aged 0-2 years. In a one-to-one interview, participants completed an adapted Arabic version of the HFIAS. In order to evaluate the validity of the HFIAS, basic sociodemographic information, anthropometric measurements of the mother and child, and dietary intake data of the child were obtained. In order to examine reproducibility, the HFIAS was re-administered after 3 months. Rural Lebanon. Mother and child pairs (n 150). Factor analysis of HFIAS items revealed two factors: 'insufficient food quality' and 'insufficient food quantity'. Using Pearson's correlation, food insecurity was inversely associated with mother's and father's education levels, number of cars and electrical appliances in the household, income, weight-for-age and length-for-age of the child and the child's dietary adequacy. In contrast, mother's BMI and crowding index were positively associated with food insecurity scores (P < 0·05 for all correlations). Cronbach's α of the scale was 0·91. A moderate correlation was observed between the two administrations of the questionnaire (intra-class correlation = 0·58; P < 0·05). Our findings indicated that the adapted Arabic version of the HFIAS is a valid and reliable tool to assess food insecurity in rural Lebanon, lending further evidence to the utility of the HFIAS in assessing food insecurity in culturally diverse populations.

Projection for household development in China.

PubMed

Guo, Z

1991-01-01

In traditional Chinese culture, marriage and setting up a new household is the most important event in life with the requisite purchases of real estate, furniture and other large items from years of savings. The development of the national economy depends on these households to as significant extent as they also provide microeconomic functions in society. The sex age-specific householder rate method was used for forecasting the number of future households. The UN medium projection of the population of China for the year 2000 indicated 1,285,000,000, the low projection showed 1,260,000,000 and the high projection came up with 1,300,000,000 with an essentially unchanged number of households and probably smaller average household size. The 1988, the China Population Statistics Almanac disclosed that in 1987 there was a total 258,340,000 households expected to increase according to the medium projection to 370,000,000 households expected to increase according to the medium projection to 370,640,000 by 2000. This annual growth rate of 2.8% exceeds the rate of 1.4% in the 1950s, 1.8% in the 1960s and early 1970s and 2.4% during 1975-87. The data of the Statistics Bureau and the Ministry of Public Security for 1985-89 yielded an annual household growth rate of 3.6%. This could be attributed to the increased number of births following the troublesome early 1960s who enter marriage age now. Based on the average household living space of 61.37 sq m there would be an additional 6,890,000,000 sq m of living space requirement for 112,300,000 new households. The proportion of urban population would rise from the level of 1987 when the agricultural population made up 80.1% and the nonagricultural segment comprised 19.8%. New household construction would require planning, raising funds, building materials, construction teams, and land.

Residential energy use and potential conservation through reduced laundering temperatures in the United States and Canada.

PubMed

Sabaliunas, Darius; Pittinger, Charles; Kessel, Cristy; Masscheleyn, Patrick

2006-04-01

A residential energy-use model was developed to estimate energy budgets for household laundering practices in the United States and Canada. The thermal energy for heating water and mechanical energy for agitating clothes in conventional washing machines were calculated for representative households in the United States and Canada. Comparisons in energy consumption among hot-, warm-, and cold-water wash and rinse cycles, horizontal- and vertical-axis washing machines, and gas and electric water heaters, were calculated on a per-wash-load basis. Demographic data for current laundering practices in the United States and Canada were then incorporated to estimate household and national energy consumption on an annual basis for each country. On average, the thermal energy required to heat water using either gas or electric energy constitutes 80% to 85% of the total energy consumed per wash in conventional, vertical-axis (top-loading) washing machines. The balance of energy used is mechanical energy. Consequently, the potential energy savings per load in converting from hot-and-warm- to cold-wash temperatures can be significant. Annual potential energy and cost savings and reductions in carbon dioxide emissions are also estimated for each country, assuming full conversion to cold-wash water temperatures. This study provides useful information to consumers for conserving energy in the home, as well as to, manufacturers in the design of more energy-efficient laundry formulations and appliances.

Mass balance and life cycle assessment of the waste electrical and electronic equipment management system implemented in Lombardia Region (Italy).

PubMed

Biganzoli, L; Falbo, A; Forte, F; Grosso, M; Rigamonti, L

2015-08-15

Waste electrical and electronic equipment (WEEE) is one of the fastest growing waste streams in Europe, whose content of hazardous substances as well as of valuable materials makes the study of the different management options particularly interesting. The present study investigates the WEEE management system in Lombardia Region (Italy) in the year 2011 by applying the life cycle assessment (LCA) methodology. An extensive collection of primary data was carried out to describe the main outputs and the energy consumptions of the treatment plants. Afterwards, the benefits and burdens associated with the treatment and recovery of each of the five categories in which WEEE is classified according to the Italian legislation (heaters and refrigerators - R1, large household appliances - R2, TV and monitors - R3, small household appliances - R4 and lighting equipment - R5) were evaluated. The mass balance of the treatment and recovery system of each of the five WEEE categories showed that steel and glass are the predominant streams of materials arising from the treatment; a non-negligible amount of plastic is also recovered, together with small amounts of precious metals. The LCA of the regional WEEE management system showed that the benefits associated with materials and energy recovery balance the burdens of the treatment processes, with the sole exception of two impact categories (human toxicity-cancer effects and freshwater ecotoxicity). The WEEE categories whose treatment and recovery resulted more beneficial for the environment and the human health are R3 and R5. The contribution analysis showed that overall the main benefits are associated with the recovery of metals, as well as of plastic and glass. Some suggestions for improving the performance of the system are given, as well as an indication for a more-in-depth analysis for the toxicity categories and a proposal for a new characterisation method for WEEE. Copyright © 2015 Elsevier B.V. All rights reserved.

California's crisis: An exploratory analysis of lifestyle, energy use, and conservation

NASA Astrophysics Data System (ADS)

Gossard, Marcia Hill

Electricity is one of the most serious issues of the 21st century. Modern human societies have become completely dependent upon energy to power modern life---resulting in unwanted environmental effects. Although electricity itself is invisible, many of the most conspicuous household items consume the most electricity. The 2001 energy crisis in California provides a unique opportunity to study how people negotiated their lives during a time of perceived resource scarcity, increased electricity prices, and threats of blackouts. Combining cultural and environmental literatures, I argued that changes in resource availability (perceived or real) led to unsettled lives in which beliefs, rituals and ways of behaving began to be questioned---resulting in new patterns of action organized around lifestyle. As a conceptual framework, lifestyle can be useful for understanding the patterns of people's everyday lives, the objects they consume, and the degrees to which those lifestyles affect the environment. Using data from the California Residential Electricity Conservation Study (CRECS), this research explores the ways households navigated and used different conservation strategies during the summers of 2001 and 2002. Analysis of Behavioral Conservation Strategies (BCS) that require ongoing effort and attention by household residents in order to achieve successful conservation outcomes (e.g., turning off lights or regulating indoor temperature), and Consumer Investment Strategies (CIS) that are one-time purchases improving efficiency (e.g., purchase of an appliance or fixture) reveal different strategies of action over the two years. Wealth indicators and time constraints were less important for predicting conservation, while cultural differences and household composition were better predictors of conservation efforts. In addition, despite assumptions that people are unwilling to change their lifestyle in order to conserve electricity, households employed more strategies that required daily effort and vigilance than one-time consumer actions. Furthermore, many households continued many conservation efforts in the year following the crisis, and there was not an immediate "snap-back" to pre-crisis behaviors. Not only did households employ a variety of conservation strategies that required changes to their lifestyle, the majority did not believe that their quality of life had been reduced or that their conservation efforts involved sacrifices.

Real-Time Detection and Reading of LED/LCD Displays for Visually Impaired Persons

PubMed Central

Tekin, Ender; Coughlan, James M.; Shen, Huiying

2011-01-01

Modern household appliances, such as microwave ovens and DVD players, increasingly require users to read an LED or LCD display to operate them, posing a severe obstacle for persons with blindness or visual impairment. While OCR-enabled devices are emerging to address the related problem of reading text in printed documents, they are not designed to tackle the challenge of finding and reading characters in appliance displays. Any system for reading these characters must address the challenge of first locating the characters among substantial amounts of background clutter; moreover, poor contrast and the abundance of specular highlights on the display surface – which degrade the image in an unpredictable way as the camera is moved – motivate the need for a system that processes images at a few frames per second, rather than forcing the user to take several photos, each of which can take seconds to acquire and process, until one is readable. We describe a novel system that acquires video, detects and reads LED/LCD characters in real time, reading them aloud to the user with synthesized speech. The system has been implemented on both a desktop and a cell phone. Experimental results are reported on videos of display images, demonstrating the feasibility of the system. PMID:21804957

DC-based smart PV-powered home energy management system based on voltage matching and RF module.

PubMed

Sabry, Ahmad H; Hasan, W Z W; Ab Kadir, Mza; Radzi, M A M; Shafie, S

2017-01-01

The main tool for measuring system efficiency in homes and offices is the energy monitoring of the household appliances' consumption. With the help of GUI through a PC or smart phone, there are various applications that can be developed for energy saving. This work describes the design and prototype implementation of a wireless PV-powered home energy management system under a DC-distribution environment, which allows remote monitoring of appliances' energy consumptions and power rate quality. The system can be managed by a central computer, which obtains the energy data based on XBee RF modules that access the sensor measurements of system components. The proposed integrated prototype framework is characterized by low power consumption due to the lack of components and consists of three layers: XBee-based circuit for processing and communication architecture, solar charge controller, and solar-battery-load matching layers. Six precise analogue channels for data monitoring are considered to cover the energy measurements. Voltage, current and temperature analogue signals were accessed directly from the remote XBee node to be sent in real time with a sampling frequency of 11-123 Hz to capture the possible surge power. The performance shows that the developed prototype proves the DC voltage matching concept and is able to provide accurate and precise results.

Initial Evaluation of a Titration Appliance for Temporary Treatment of Obstructive Sleep Apnea.

PubMed

Levendowski, Daniel J; Morgan, Todd; Westbrook, Philip

2012-01-01

Custom oral appliances that adjustably advance the mandible provide superior outcomes when treating patients with moderate or severe sleep apnea. Custom appliances, however, are expensive, must be fitted by a dentist, and the likelihood of successful outcomes are difficult to predict. An inexpensive trial appliance, if proven efficacious, might be used to predict custom appliance outcomes or to provide temporary therapeutic benefit. The aim of this initial study was to assess the treatment efficacy of a novel titration oral appliance with that of an optimized custom appliance. Seventeen patients, treated with a custom oral appliance for at least one year, successfully completed a three-night home sleep test. The baseline obstructive sleep apnea severity was established on Night 1 with seven patients exhibiting severe, six moderate and four mild apnea/hypopnea indexes. Patients were randomly assigned to wear their custom appliance or the titration appliance on Nights 2 and 3. Significant reductions in the mean overall and supine apnea indexes (p < 0.05), and the overall (p < 0.01) and supine (p < 0.05) apnea/hypopnea indexes were observed for both the titration and custom appliances. The proportion of patients who exhibited at least a 50% reduction in the overall apnea index and supine apnea/hypopnea were similar for the titration and custom appliance (~60%). The custom appliance reduced the overall apnea/hypopnea index by 50% in a greater proportion of the patients compared to the titration appliance (77% vs. 53%). The titration appliance significantly reduced the degree of hypoxic exposure across sleep disordered breathing events overall (p < 0.05) and supine (p < 0.01). Patients found their custom appliance was more comfortable than the titration appliance, but preferred the titration appliance to no therapy. The titration appliance may be useful in assessing oral appliance treatment efficacy. When set to 70% of maximum protrusion, the titration appliance may provide immediate, temporary therapeutic benefit.

Initial Evaluation of a Titration Appliance for Temporary Treatment of Obstructive Sleep Apnea

PubMed Central

Levendowski, Daniel J.; Morgan, Todd; Westbrook, Philip

2015-01-01

Background Custom oral appliances that adjustably advance the mandible provide superior outcomes when treating patients with moderate or severe sleep apnea. Custom appliances, however, are expensive, must be fitted by a dentist, and the likelihood of successful outcomes are difficult to predict. An inexpensive trial appliance, if proven efficacious, might be used to predict custom appliance outcomes or to provide temporary therapeutic benefit. Objective The aim of this initial study was to assess the treatment efficacy of a novel titration oral appliance with that of an optimized custom appliance. Methods Seventeen patients, treated with a custom oral appliance for at least one year, successfully completed a three-night home sleep test. The baseline obstructive sleep apnea severity was established on Night 1 with seven patients exhibiting severe, six moderate and four mild apnea/hypopnea indexes. Patients were randomly assigned to wear their custom appliance or the titration appliance on Nights 2 and 3. Results Significant reductions in the mean overall and supine apnea indexes (p < 0.05), and the overall (p < 0.01) and supine (p < 0.05) apnea/hypopnea indexes were observed for both the titration and custom appliances. The proportion of patients who exhibited at least a 50% reduction in the overall apnea index and supine apnea/hypopnea were similar for the titration and custom appliance (~60%). The custom appliance reduced the overall apnea/hypopnea index by 50% in a greater proportion of the patients compared to the titration appliance (77% vs. 53%). The titration appliance significantly reduced the degree of hypoxic exposure across sleep disordered breathing events overall (p < 0.05) and supine (p < 0.01). Patients found their custom appliance was more comfortable than the titration appliance, but preferred the titration appliance to no therapy. Conclusion The titration appliance may be useful in assessing oral appliance treatment efficacy. When set to 70% of maximum protrusion, the titration appliance may provide immediate, temporary therapeutic benefit. PMID:26523244

Disaster loss and social media: Can online information increase flood resilience?

NASA Astrophysics Data System (ADS)

Allaire, Maura C.

2016-09-01

When confronted with natural disasters, individuals around the world increasingly use online resources to become informed of forecasted conditions and advisable actions. This study tests the effectiveness of online information and social media in enabling households to reduce disaster losses. The 2011 Bangkok flood is utilized as a case study since it was one of the first major disasters to affect a substantial population connected to social media. The role of online information is investigated with a mixed methods approach. Both quantitative (propensity score matching) and qualitative (in-depth interviews) techniques are employed. The study relies on two data sources—survey responses from 469 Bangkok households and in-depth interviews with internet users who were a subset of the survey participants. Propensity score matching indicates that social media enabled households to reduce flood losses by an average of 37% (USD 3708 per household), using a nearest neighbor estimator. This reduction is substantial when considering that household flood losses for the matched sample averaged USD 8278. Social media offered information not available from other sources, such as localized and nearly real-time updates of flood location and depth. With this knowledge, households could move belongings to higher ground before floodwaters arrived. These findings suggest that utilizing social media users as sensors could better inform populations during disasters. Overall, the study reveals that online information can enable effective disaster preparedness and reduce losses.

Municipal household solid waste fee based on an increasing block pricing model in Beijing, China.

PubMed

Chu, Zhujie; Wu, Yunga; Zhuang, Jun

2017-03-01

This article aims to design an increasing block pricing model to estimate the waste fee with the consideration of the goals and principles of municipal household solid waste pricing. The increasing block pricing model is based on the main consideration of the per capita disposable income of urban residents, household consumption expenditure, production rate of waste disposal industry, and inflation rate. The empirical analysis is based on survey data of 5000 households in Beijing, China. The results indicate that the current uniform price of waste disposal is set too high for low-income people, and waste fees to the household disposable income or total household spending ratio are too low for the medium- and high-income families. An increasing block pricing model can prevent this kind of situation, and not only solve the problem of lack of funds, but also enhance the residents' awareness of environmental protection. A comparative study based on the grey system model is made by having a preliminary forecast for the waste emissions reduction effect of the pay-as-you-throw programme in the next 5 years of Beijing, China. The results show that the effect of the pay-as-you-throw programme is not only to promote the energy conservation and emissions reduction, but also giving a further improvement of the environmental quality.

46 CFR 111.77-3 - Appliances.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances. 111.77-3 Section 111.77-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Appliances and Appliance Circuits § 111.77-3 Appliances. All electrical appliances, including, but...

Environmental predictors of stunting among children under-five in Somalia: cross-sectional studies from 2007 to 2010.

PubMed

Kinyoki, Damaris K; Berkley, James A; Moloney, Grainne M; Odundo, Elijah O; Kandala, Ngianga-Bakwin; Noor, Abdisalan M

2016-07-28

Stunting among children under five years old is associated with long-term effects on cognitive development, school achievement, economic productivity in adulthood and maternal reproductive outcomes. Accurate estimation of stunting and tools to forecast risk are key to planning interventions. We estimated the prevalence and distribution of stunting among children under five years in Somalia from 2007 to 2010 and explored the role of environmental covariates in its forecasting. Data from household nutritional surveys in Somalia from 2007 to 2010 with a total of 1,066 clusters covering 73,778 children were included. We developed a Bayesian hierarchical space-time model to forecast stunting by using the relationship between observed stunting and environmental covariates in the preceding years. We then applied the model coefficients to environmental covariates in subsequent years. To determine the accuracy of the forecasting, we compared this model with a model that used data from all the years with the corresponding environmental covariates. Rainfall (OR = 0.994, 95 % Credible interval (CrI): 0.993, 0.995) and vegetation cover (OR = 0.719, 95 % CrI: 0.603, 0.858) were significant in forecasting stunting. The difference in estimates of stunting using the two approaches was less than 3 % in all the regions for all forecast years. Stunting in Somalia is spatially and temporally heterogeneous. Rainfall and vegetation are major drivers of these variations. The use of environmental covariates for forecasting of stunting is a potentially useful and affordable tool for planning interventions to reduce the high burden of malnutrition in Somalia.

24 CFR 3280.707 - Heat producing appliances.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 24 Housing and Urban Development 5 2012-04-01 2012-04-01 false Heat producing appliances. 3280.707... Systems § 3280.707 Heat producing appliances. (a) Heat-producing appliances and vents, roof jacks and...) Fuel-burning heat-producing appliances and refrigeration appliances, except ranges and ovens, shall be...

24 CFR 3280.707 - Heat producing appliances.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Heat producing appliances. 3280.707... Systems § 3280.707 Heat producing appliances. (a) Heat-producing appliances and vents, roof jacks and...) Fuel-burning heat-producing appliances and refrigeration appliances, except ranges and ovens, shall be...

Natural Aggregation Approach based Home Energy Manage System with User Satisfaction Modelling

NASA Astrophysics Data System (ADS)

Luo, F. J.; Ranzi, G.; Dong, Z. Y.; Murata, J.

2017-07-01

With the prevalence of advanced sensing and two-way communication technologies, Home Energy Management System (HEMS) has attracted lots of attentions in recent years. This paper proposes a HEMS that optimally schedules the controllable Residential Energy Resources (RERs) in a Time-of-Use (TOU) pricing and high solar power penetrated environment. The HEMS aims to minimize the overall operational cost of the home, and the user’s satisfactions and requirements on the operation of different household appliances are modelled and considered in the HEMS. Further, a new biological self-aggregation intelligence based optimization technique previously proposed by the authors, i.e., Natural Aggregation Algorithm (NAA), is applied to solve the proposed HEMS optimization model. Simulations are conducted to validate the proposed method.

Fundamentals of electric power conversion. Volume 2, Energy-efficient polyphase AC induction motors, final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umans, S.D.

1992-12-01

Its rugged nature and straightforward design make the induction motor the most commonly used type of electric motor. This motor ranges in size fro the fractional-horsepower, single-phase motors found in household appliances to polyphase motors rated at thousands of horsepower for industrial applications. Volume 1 of this report describes the function of induction motors, their characteristics, and induction motor testing. Volume 2 describes the characteristics of high-efficiency induction motors, with emphasis on the techniques used to obtain high efficiency. This two-volume report is written in nontechnical language and is intended for readers who require background from applications, marketing, motor planning,more » or managerial perspective.« less

Fundamentals of electric power conversion. Volume 1, Operating characteristics and testing of AC induction motors, final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Umans, S.D.

1992-12-01

Its rugged nature and straightforward design make the induction motor the most commonly used type of electric motor. This motor ranges in size from the fractional-horsepower, single-phase motors found in household appliances to polyphase motors rated at thousands of horsepower for industrial applications. Volume 1 of this report describes the function of induction motors, their characteristics, and induction motor testing. Volume 2 describes the characteristics of high-efficiency induction motors, with emphasis on the techniques used to obtain high efficiency. This two-volume report is written in nontechnical language and is intended for readers who require background from an applications, marketing, motormore » planning, or managerial perspective.« less

76 FR 58345 - Energy Conservation Program: Test Procedures for Residential Dishwashers, Dehumidifiers, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-20

...Where appropriate, the U.S. Department of Energy (DOE) has proposed to amend its test procedures for residential dishwashers, dehumidifiers, and conventional cooking products (which includes cooktops, ovens, and ranges) to include provisions for measuring standby mode and off mode energy consumption, as required by the Energy Independence and Security Act of 2007 (EISA 2007). These test procedure amendments would incorporate by reference certain provisions of the International Electrotechnical Commission (IEC) Standard 62301, ``Household electrical appliances--Measurement of standby power.'' Since publication of DOE's initial proposal in December 2010, the IEC has replaced the First Edition of this standard with the current Second Edition. This supplemental notice of proposed rulemaking proposes to incorporate the latest edition of IEC Standard 62301.

Three strategies for conservation

NASA Technical Reports Server (NTRS)

1975-01-01

The three strategies considered as energy conservation oriented were given: national energy conservation, electrification, and diversification. The first one applies to the near term period (now-1985), the second one to the mid term (1985-2000), and the third one to the far term (2000- ). The rest of this section was focussed on the near term period. The following proposed actions were considered: (1) roll back the price of newly discovered oil, (2) force conversion of many power plants from gas and oil to coal, (3) freeze gasoline production for three years at 1972 levels, (4) mandate automobile mileage requirements, (5) require industry to improve energy efficiency, and (6) require manufacture of household appliances with greater efficiency. Each of these six actions was described and discussed in more detail.

Optimal urban water conservation strategies considering embedded energy: coupling end-use and utility water-energy models.

NASA Astrophysics Data System (ADS)

Escriva-Bou, A.; Lund, J. R.; Pulido-Velazquez, M.; Spang, E. S.; Loge, F. J.

2014-12-01

Although most freshwater resources are used in agriculture, a greater amount of energy is consumed per unit of water supply for urban areas. Therefore, efforts to reduce the carbon footprint of water in cities, including the energy embedded within household uses, can be an order of magnitude larger than for other water uses. This characteristic of urban water systems creates a promising opportunity to reduce global greenhouse gas emissions, particularly given rapidly growing urbanization worldwide. Based on a previous Water-Energy-CO2 emissions model for household water end uses, this research introduces a probabilistic two-stage optimization model considering technical and behavioral decision variables to obtain the most economical strategies to minimize household water and water-related energy bills given both water and energy price shocks. Results show that adoption rates to reduce energy intensive appliances increase significantly, resulting in an overall 20% growth in indoor water conservation if household dwellers include the energy cost of their water use. To analyze the consequences on a utility-scale, we develop an hourly water-energy model based on data from East Bay Municipal Utility District in California, including the residential consumption, obtaining that water end uses accounts for roughly 90% of total water-related energy, but the 10% that is managed by the utility is worth over 12 million annually. Once the entire end-use + utility model is completed, several demand-side management conservation strategies were simulated for the city of San Ramon. In this smaller water district, roughly 5% of total EBMUD water use, we found that the optimal household strategies can reduce total GHG emissions by 4% and utility's energy cost over 70,000/yr. Especially interesting from the utility perspective could be the "smoothing" of water use peaks by avoiding daytime irrigation that among other benefits might reduce utility energy costs by 0.5% according to our assessment.

Economic motivation of households to undertake private precautionary measures against floods

NASA Astrophysics Data System (ADS)

Kreibich, H.; Christenberger, S.; Schwarze, R.

2011-02-01

Flood damage is on the increase due to a combination of growing vulnerability and a changing climate. This trend can be mitigated only through significantly improved flood risk management which, alongside the efforts of public authorities, will include improvements in the mitigation measures adopted by private households. Economically "reasonable" efforts to self-insure and self-protect should be expected from households before the government steps in with publicly-funded relief programmes. To gain a deeper understanding of the benefits of households' precautionary measures, telephone interviews with private home owners were conducted in the Elbe and Danube catchments in Germany after the floods of 2002 and again after the floods in 2005 and 2006. Only detached, solid single-family houses were included in this study, which is based on 759 interviews. In addition, market-based cost assessments were solicited based on a "model building". Expert interviews and a literature review - including catalogues and price lists for building materials and household appliances - were used as back-up information for the cost assessments. The comparison of costs and benefits shows that large investments, such as building a sealed cellar, are only economically efficient if the building is flooded very frequently, that is, if it is located in a high flood risk area. In such areas it would be preferable in economic terms not to build a new house at all - or else to build a house without a cellar. Small investments, however, such as oil tank protection, can prevent serious damage at low cost. Such investments are still profitable even if the building is flooded every 50 years or less on average. It could be argued that these low-cost measures should be made mandatory through the enforcement of building codes. Financial incentives built into insurance contracts coupled with limits set on governmental relief programmes would provide an economic motivation for people to invest in precautionary measures.

Environmental prediction, risk assessment and extreme events: adaptation strategies for the developing world

PubMed Central

Webster, Peter J.; Jian, Jun

2011-01-01

The uncertainty associated with predicting extreme weather events has serious implications for the developing world, owing to the greater societal vulnerability to such events. Continual exposure to unanticipated extreme events is a contributing factor for the descent into perpetual and structural rural poverty. We provide two examples of how probabilistic environmental prediction of extreme weather events can support dynamic adaptation. In the current climate era, we describe how short-term flood forecasts have been developed and implemented in Bangladesh. Forecasts of impending floods with horizons of 10 days are used to change agricultural practices and planning, store food and household items and evacuate those in peril. For the first time in Bangladesh, floods were anticipated in 2007 and 2008, with broad actions taking place in advance of the floods, grossing agricultural and household savings measured in units of annual income. We argue that probabilistic environmental forecasts disseminated to an informed user community can reduce poverty caused by exposure to unanticipated extreme events. Second, it is also realized that not all decisions in the future can be made at the village level and that grand plans for water resource management require extensive planning and funding. Based on imperfect models and scenarios of economic and population growth, we further suggest that flood frequency and intensity will increase in the Ganges, Brahmaputra and Yangtze catchments as greenhouse-gas concentrations increase. However, irrespective of the climate-change scenario chosen, the availability of fresh water in the latter half of the twenty-first century seems to be dominated by population increases that far outweigh climate-change effects. Paradoxically, fresh water availability may become more critical if there is no climate change. PMID:22042897

Household energy management strategies in Bulgaria's transitioning energy sector

NASA Astrophysics Data System (ADS)

Carper, Mark Daniel Lynn

Recent transition literature of post-socialist states has addressed the shortcomings of a rapid blanket implementation of neo-liberal policies and practices placed upon a landscape barren of the needed institutions and experiences. Included in these observations are the policy-making oversight of spatial socioeconomic variations and their individual and diverse methods of coping with their individual challenges. Of such literature addressing the case of Bulgaria, a good portion deals with the spatial consequences of restructuring as well as with embedded disputes over access to and control of resources. With few exceptions, studies of Bulgaria's changing energy sector have largely been at the state level and have not been placed within the context of spatial disparities of socioeconomic response. By exploring the variations of household energy management strategies across space, my dissertation places this resource within such a theoretical context and offers analysis based on respective levels of economic and human development, inherited material infrastructures, the organization and activities of institutions, and fuel and technological availability. A closed survey was distributed to explore six investigational themes across four geographic realms. The investigational themes include materials of housing construction, methods of household heating, use of electrical appliances, energy conservation strategies, awareness and use of energy conservation technologies, and attitudes toward the transitioning energy sector. The geographic realms include countrywide results, the urban-rural divide, regional variations, and urban divisions of the capital city, Sofia. Results conclude that, indeed, energy management strategies at the household level have been shaped by multiple variables, many of which differ across space. These variables include price sensitivity, degree of dependence on remnant technologies, fuel and substitute availability, and level of human and socioeconomic development. Thus far, the state has taken a very limited role in improving residential energy efficiency despite the increased energy expenditure burdens that most households face. Yet lacking are affordable technologies, educational campaigns, and individual financing mechanisms or incentives. As shown, where there is an informed, active, and financially capable population, improved household efficiency is more likely to be the winning strategy for both the goals of the individual as well as of the state.

Increased BMI in children-an indicator for less compliance during orthodontic treatment with removable appliances.

PubMed

von Bremen, Julia; Lorenz, Nathalie; Ludwig, Björn; Ruf, Sabine

2018-02-19

To assess whether or not childhood overweight is associated with lower levels of compliance during orthodontic therapy with removable appliances. Starting in 2011, all upper expansion plates and Sander II appliances were equipped with a Theramon® microsensor chip to assess appliance wear time objectively. According to their pre-treatment, BMI normal weight patients were matched to consecutively treated overweight or obese patients by gender, age, and appliance type. Cooperation was assessed with microelectronic wear time documentation over a period of at least 6 months. A total of 50 patients (25 overweight, 25 normal weight) with upper expansion plates and 64 patients (32 overweight, 32 normal weight) with Sander II appliances were analysed. Spearman Rho coefficients showed an indirect association between BMI and appliance wear time, indicating that the higher the BMI, the less the patients wore their appliances (P < 0.05). Furthermore, both normal- and overweight children wore upper expansion plates significantly more than Sander II appliances (P < 0.05). Although no gender-specific difference was found (P = 0.723), an age-related correlation could be verified, indicating a decrease in wear time with increasing age (P < 0.05). An increased BMI appears to be a risk factor for less appliance wear during orthodontic treatment with removable appliances. Additional factors which influenced cooperation during treatment with removable appliances were patient age and appliance type.

46 CFR 199.170 - Line-throwing appliance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Line-throwing appliance. 199.170 Section 199.170 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS... appliance. (a) General. Each vessel must have a line-throwing appliance approved under approval series 160...

24 CFR 3280.807 - Fixtures and appliances.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically listed...

Effects of fixed labial orthodontic appliances on speech sound production.

PubMed

Paley, Jonathan S; Cisneros, George J; Nicolay, Olivier F; LeBlanc, Etoile M

2016-05-01

To explore the impact of fixed labial orthodontic appliances on speech sound production. Speech evaluations were performed on 23 patients with fixed labial appliances. Evaluations were performed immediately prior to appliance insertion, immediately following insertion, and 1 and 2 months post insertion. Baseline dental/skeletal variables were correlated with the ability to accommodate the presence of the appliances. Appliance effects were variable: 44% of the subjects were unaffected, 39% were temporarily affected but adapted within 2 months, and 17% of patients showed persistent sound errors at 2 months. Resolution of acquired sound errors was noted by 8 months post-appliance removal. Maladaptation to appliances was correlated to severity of malocclusion as determined by the Grainger's Treatment Priority Index. Sibilant sounds, most notably /s/, were affected most often. (1) Insertion of fixed labial appliances has an effect on speech sound production. (2) Sibilant and stopped sounds are affected, with /s/ being affected most often. (3) Accommodation to fixed appliances depends on the severity of malocclusion.

46 CFR 188.27-1 - Lifesaving appliances and arrangements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 188.27-1 Section... VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 188.27-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements shall be in accordance with the requirements for...

46 CFR 90.27-1 - Lifesaving appliances and arrangements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 90.27-1 Section... VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 90.27-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements must be in accordance with subchapter W (Lifesaving...

46 CFR 195.06-1 - Lifesaving appliances and arrangements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 195.06-1 Section... VESSELS VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Lifesaving Appliances and Arrangements § 195.06-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements shall be...

46 CFR 70.28-1 - Lifesaving appliances and arrangements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 70.28-1 Section... PROVISIONS Lifesaving Appliances and Arrangements § 70.28-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements on passenger vessels must be in accordance with subchapter W...

7 CFR 3300.37 - Testing of a mechanical refrigerating appliance.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Testing of a mechanical refrigerating appliance. 3300... SPECIAL EQUIPMENT Procedures for Separate Testing of Mechanical Refrigerating Appliances § 3300.37 Testing of a mechanical refrigerating appliance. For separate testing of a mechanical refrigerating appliance...

Choosing Wood Burning Appliances

EPA Pesticide Factsheets

Information to assist consumers in choosing a wood burning appliance, including types of appliances, the differences between certified and non-certified appliances, and alternative wood heating options.

49 CFR 173.219 - Life-saving appliances.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false Life-saving appliances. 173.219 Section 173.219... Life-saving appliances. (a) A life-saving appliance, self-inflating or non-self-inflating, containing small quantities of hazardous materials that are required as part of the life-saving appliance must...

49 CFR 173.219 - Life-saving appliances.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Life-saving appliances. 173.219 Section 173.219... Life-saving appliances. (a) A life-saving appliance, self-inflating or non-self-inflating, containing small quantities of hazardous materials that are required as part of the life-saving appliance must...

14 CFR 21.305 - Approval of materials, parts, processes, and appliances.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., and appliances. 21.305 Section 21.305 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION..., Parts, Processes, and Appliances § 21.305 Approval of materials, parts, processes, and appliances. Whenever a material, part, process, or appliance is required to be approved under this chapter, it may be...

New horizons in orthodontics & dentofacial orthopedics: fixed Twin Blocks & TransForce lingual appliances.

PubMed

Clark, William John

2011-01-01

During the 20th century functional appliances evolved from night time wear to more flexible appliances for increased day time wear to full time wear with Twin Block appliances. The current trend is towards fixed functional appliances and this paper introduces the Fixed Twin Block, bonded to the teeth to eliminate problems of compliance in functional therapy. TransForce lingual appliances are pre-activated and may be used in first phase treatment for sagittal and transverse arch development. Alternatively they may be integrated with fixed appliances at any stage of treatment.

Acceptability and attractiveness of intra- and extra-oral orthodontic appliances.

PubMed

Abu Alhaija, Elham S J; Karajeh, M A

2013-01-01

To evaluate the acceptability of different intra-oral and extra-oral orthodontic appliances, to rank orthodontic appliances from the most to the least attractive and to investigate the factors that may affect the acceptance of orthodontic treatment. A random sample of 800 students (schoolchildren and university students) were invited to participate in this study and a total of 688 students were included (86%). A self-administrated structured questionnaire was constructed for the purpose of this study. More than one-half in each age group (53%) claimed that they would accept to have orthodontic treatment. Acceptance of the different orthodontic appliances was affected by gender, age and type of school. Removable appliance was reported as the most acceptable and facemask was reported as the least acceptable orthodontic appliances. Majority of subjects ranked ceramic and facemask appliances as the most and the least attractive orthodontic appliances, respectively. The predictor variables for the acceptance of orthodontic treatment were perceived demand for orthodontic treatment, perceived positive effect of orthodontic treatment and expected benefits from orthodontic treatment. Removable appliance was the most acceptable orthodontic appliance whereas ceramic appliance was ranked as the most attractive one. Facemask was the least acceptable and the least attractive option.

Perceived Effectiveness, Self-efficacy, and Social Support for Oral Appliance Therapy Among Older Veterans With Obstructive Sleep Apnea.

PubMed

Carballo, Nancy J; Alessi, Cathy A; Martin, Jennifer L; Mitchell, Michael N; Hays, Ron D; Col, Nananda; Patterson, Emily S; Jouldjian, Stella; Josephson, Karen; Fung, Constance H

2016-11-01

Obstructive sleep apnea is a prevalent sleep disorder among older adults. Oral appliances are increasingly prescribed as therapy for obstructive sleep apnea. Adherence to oral appliance therapy is highly variable. Based on value-expectancy theory and other social-psychological theories, adherence to oral appliance therapy may be influenced by patients' perceived effectiveness of the therapy, self-efficacy, and availability of social support. We examined these perceptions among older adults with obstructive sleep apnea who were prescribed oral appliance therapy. We mailed surveys to all patients aged ≥65 years who had been prescribed oral appliance therapy for obstructive sleep apnea over the prior 36 months at a Veterans Affairs medical center. We examined frequencies of responses to items that assessed perceived effectiveness, self-efficacy, and social support for nightly use of oral appliances from friends, family, or health care staff. Thirty-nine individuals responded (response rate, 30%; mean [SD] age 71.4 [SD 6.3] years; 97% male). Thirty-six percent of the respondents perceived regular use of oral appliance therapy to be effective in managing obstructive sleep apnea; 39% agreed that they felt confident about using oral appliances regularly; 41% felt supported by people in their life in using oral appliance therapy; and 38% agreed that health care staff would help them to use their oral appliance regularly. These rates represented less than half of respondents despite the finding that 65% of patients believed that they would use their oral appliance regularly. Although oral appliance therapy is increasingly prescribed for obstructive sleep apnea, only about one third of older adults prescribed it perceived it to be an effective treatment, were confident about oral appliance use, and/or believed that they would receive needed support. Future research is needed to better understand older adults' perceptions so that interventions can be designed to improve the effectiveness of oral appliances, their self-efficacy for using oral appliances, and their social support for this therapy, which may, in turn, improve oral appliance therapy adherence. Published by Elsevier Inc.

Estimating Household Travel Energy Consumption in Conjunction with a Travel Demand Forecasting Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garikapati, Venu M.; You, Daehyun; Zhang, Wenwen

This paper presents a methodology for the calculation of the consumption of household travel energy at the level of the traffic analysis zone (TAZ) in conjunction with information that is readily available from a standard four-step travel demand model system. This methodology embeds two algorithms. The first provides a means of allocating non-home-based trips to residential zones that are the source of such trips, whereas the second provides a mechanism for incorporating the effects of household vehicle fleet composition on fuel consumption. The methodology is applied to the greater Atlanta, Georgia, metropolitan region in the United States and is foundmore » to offer a robust mechanism for calculating the footprint of household travel energy at the level of the individual TAZ; this mechanism makes possible the study of variations in the energy footprint across space. The travel energy footprint is strongly correlated with the density of the built environment, although socioeconomic differences across TAZs also likely contribute to differences in travel energy footprints. The TAZ-level calculator of the footprint of household travel energy can be used to analyze alternative futures and relate differences in the energy footprint to differences in a number of contributing factors and thus enables the design of urban form, formulation of policy interventions, and implementation of awareness campaigns that may produce more-sustainable patterns of energy consumption.« less

Distribution System Pricing with Distributed Energy Resources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hledik, Ryan; Lazar, Jim; Schwartz, Lisa

Technological changes in the electric utility industry bring tremendous opportunities and significant challenges. Customers are installing clean sources of on-site generation such as rooftop solar photovoltaic (PV) systems. At the same time, smart appliances and control systems that can communicate with the grid are entering the retail market. Among the opportunities these changes create are a cleaner and more diverse power system, the ability to improve system reliability and system resilience, and the potential for lower total costs. Challenges include integrating these new resources in a way that maintains system reliability, provides an equitable sharing of system costs, and avoidsmore » unbalanced impacts on different groups of customers, including those who install distributed energy resources (DERs) and low-income households who may be the least able to afford the transition.« less

38 CFR 17.122 - Payment or reimbursement of the expenses of repairs to prosthetic appliances and similar devices...

Code of Federal Regulations, 2010 CFR

2010-07-01

... of the expenses of repairs to prosthetic appliances and similar devices furnished without prior... Payment or reimbursement of the expenses of repairs to prosthetic appliances and similar devices furnished without prior authorization. The expenses of repairs to prosthetic appliances, or similar appliances...

46 CFR 31.36-1 - Lifesaving appliances and arrangements-TB/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements-TB/ALL. 31.36-1... CERTIFICATION Lifesaving Appliances and Arrangements § 31.36-1 Lifesaving appliances and arrangements—TB/ALL. All lifesaving appliances and arrangements on tank vessels must be in accordance with subchapter W...

Rapid tooling method for soft customized removable oral appliances.

PubMed

Salmi, Mika; Tuomi, Jukka; Sirkkanen, Rauno; Ingman, Tuula; Mäkitie, Antti

2012-01-01

Traditionally oral appliances i.e. removable orthodontic appliances, bite splints and snoring / sleep apnea appliances are made with alginate impressions and wax registrations. Our aim was to describe the process of manufacturing customized oral appliances with a new technique i.e. rapid tooling method. The appliance should ideally be custom made to match the teeth. An orthodontic patient, scheduled for conventional orthodontic treatment, served as a study subject. After a precise clinical and radiographic examination, the approach was to digitize the patient's dental arches and then to correct them virtually by computer. Additive manufacturing was then used to fabricate a mould for a soft customized appliance. The mould was manufactured using stereolithography from Somos ProtoGen O-XT 18420 material. Casting material for the mould to obtain the final appliance was silicone. As a result we managed to create a customized soft orthodontic appliance. Also, the accuracy of the method was found to be adequate. Two versions of the described device were manufactured: one with small and one with moderate orthodontic force. The study person also gave information on the subjective patient adaptation aspects of the oral appliance.

Electrical appliance energy consumption control methods and electrical energy consumption systems

DOEpatents

Donnelly, Matthew K [Kennewick, WA; Chassin, David P [Pasco, WA; Dagle, Jeffery E [Richland, WA; Kintner-Meyer, Michael [Richland, WA; Winiarski, David W [Kennewick, WA; Pratt, Robert G [Kennewick, WA; Boberly-Bartis, Anne Marie [Alexandria, VA

2006-03-07

Electrical appliance energy consumption control methods and electrical energy consumption systems are described. In one aspect, an electrical appliance energy consumption control method includes providing an electrical appliance coupled with a power distribution system, receiving electrical energy within the appliance from the power distribution system, consuming the received electrical energy using a plurality of loads of the appliance, monitoring electrical energy of the power distribution system, and adjusting an amount of consumption of the received electrical energy via one of the loads of the appliance from an initial level of consumption to an other level of consumption different than the initial level of consumption responsive to the monitoring.

Electrical appliance energy consumption control methods and electrical energy consumption systems

DOEpatents

Donnelly, Matthew K [Kennewick, WA; Chassin, David P [Pasco, WA; Dagle, Jeffery E [Richland, WA; Kintner-Meyer, Michael [Richland, WA; Winiarski, David W [Kennewick, WA; Pratt, Robert G [Kennewick, WA; Boberly-Bartis, Anne Marie [Alexandria, VA

2008-09-02

Electrical appliance energy consumption control methods and electrical energy consumption systems are described. In one aspect, an electrical appliance energy consumption control method includes providing an electrical appliance coupled with a power distribution system, receiving electrical energy within the appliance from the power distribution system, consuming the received electrical energy using a plurality of loads of the appliance, monitoring electrical energy of the power distribution system, and adjusting an amount of consumption of the received electrical energy via one of the loads of the appliance from an initial level of consumption to an other level of consumption different than the initial level of consumption responsive to the monitoring.

A System Approach to Navy Medical Education and Training. Appendix 44. Competency Curriculum for Dental Assistant.

DTIC Science & Technology

1974-08-31

Prosthodontic Appliances - Partial Dentures .... ....... ....... .... 59 2. Removable Prosthodontic Appliances - Full Dentures ..... ........... . 60 3...PROCEDURES I This unit includes the following Modules: Number Title Page 1 Removable Prosthodontic Appliances - Partial Dentures 59. ......... ...... 2...Removable Prostbodontic Appliances - Full Dentures ..... ...... a .. .. .. . 60 3 Fixed Prosthodontic Appliances - Fixed Bridge. . 61 4 Mouthquard

Transforce lingual appliances pre-adjusted invisible appliances simplify treatment.

PubMed

Clark, William John

2011-01-01

Transforce lingual appliances are designed to be used in conjunction with conventional fixed appliances. Lingual arch development is normally followed by bonded fixed appliances to detail the occlusion. Alternatively Transforce appliance treatment is an efficient method of preparing complex malocclusions prior to a finishing stage with invisible appliances. This approach is ideal for adult treatment, using light continuous forces for arch development with appliances that are comfortable to wear. Sagittal and Transverse appliances are designed for arch development in a range of sizes for contracted arches. They can be used to treat all classes of malocclusion and are pre-adjusted fixed/removable devices for non-compliance treatment. Force modules with nickel titanium coil springs enclosed in a tube deliver a gentle, biocompatible continuous force with a long range of action. They are excellent for mixed dentition and ideal for adult arch development. There are multiple sizes for upper and lower arch development and a sizing chart may be placed over a study model for correct selection, eliminating the need for laboratory work.

Introducing an operational method to forecast long-term regional drought based on the application of artificial intelligence capabilities

NASA Astrophysics Data System (ADS)

Kousari, Mohammad Reza; Hosseini, Mitra Esmaeilzadeh; Ahani, Hossein; Hakimelahi, Hemila

2017-01-01

An effective forecast of the drought definitely gives lots of advantages in regard to the management of water resources being used in agriculture, industry, and households consumption. To introduce such a model applying simple data inputs, in this study a regional drought forecast method on the basis of artificial intelligence capabilities (artificial neural networks) and Standardized Precipitation Index (SPI in 3, 6, 9, 12, 18, and 24 monthly series) has been presented in Fars Province of Iran. The precipitation data of 41 rain gauge stations were applied for computing SPI values. Besides, weather signals including Multivariate ENSO Index (MEI), North Atlantic Oscillation (NAO), Southern Oscillation Index (SOI), NINO1+2, anomaly NINO1+2, NINO3, anomaly NINO3, NINO4, anomaly NINO4, NINO3.4, and anomaly NINO3.4 were also used as the predictor variables for SPI time series forecast the next 12 months. Frequent testing and validating steps were considered to obtain the best artificial neural networks (ANNs) models. The forecasted values were mapped in verification sector then they were compared with the observed maps at the same dates. Results showed considerable spatial and temporal relationships even among the maps of different SPI time series. Also, the first 6 months forecasted maps showed an average of 73 % agreements with the observed ones. The most important finding and the strong point of this study was the fact that although drought forecast in each station and time series was completely independent, the relationships between spatial and temporal predictions remained. This strong point mainly referred to frequent testing and validating steps in order to explore the best drought forecast models from plenty of produced ANNs models. Finally, wherever the precipitation data are available, the practical application of the presented method is possible.

Advances in Oral Appliances for Obstructive Sleep Apnea.

PubMed

Jacobowitz, Ofer

2017-01-01

Oral appliances that advance the mandible are widely used as alternatives to positive airway pressure (PAP) devices or as primary therapy for obstructive sleep apnea (OSA) in adults. Although PAP is more efficacious at lowering the polysomnographic indices of OSA, the clinical effectiveness of PAP and oral appliances is similar, and patients are more likely to adhere to oral appliance therapy than to PAP treatment. Clinical examination is used to determine the candidacy of oral appliances and to select a particular appliance for a given patient. Endoscopic examination of the pharynx may be used to help assess the potential for efficacy. Otherwise, if available, titration of mandibular protrusion during sleep may be performed prior to appliance production in order to assess efficacy. Once a patient is fitted with a titratable oral appliance, further advancement is usually performed at home to resolve the clinical symptoms and signs of OSA. Clinical follow-up is needed to assess the outcome, side effects, and adherence, as the long-term adherence rate is approximately 50%. Recent advances in oral appliance therapy include the development of embedded temperature sensors for adherence monitoring and the production of thinner, lighter appliances via 3D printing techniques. © 2017 S. Karger AG, Basel.

Farmers' perceptions of and adaptation strategies to climate change and their determinants; the case of Punjab province, Pakistan

NASA Astrophysics Data System (ADS)

Abid, M.; Scheffran, J.; Schneider, U. A.; Ashfaq, M.

2014-10-01

Climate change is a global environmental threat to all economic sectors, particularly the agricultural sector. Pakistan is one of the negatively affected countries from climate change due to its high exposure to extreme events and low adaptive capacity. In Pakistan, farmers are the primary stakeholders in agriculture and are more at risk due to climate vulnerability. Based on farm household data of 450 households collected from three districts in three agro-ecological zones in Punjab province of Pakistan, this study examined how farmers perceive climate change and how they adapt their farming in response to perceived changes in climate. The results demonstrate that awareness to climate change persists in the area, and farm households make adjustments to adapt their agriculture in response to climatic change. Overall 58% of the farm households adapted their farming to climate change. Changing crop varieties, changing planting dates, plantation of trees and changing fertilizer were the main adaptation methods implemented by farm households in the study area. Results from the binary logistic model revealed that education, farm experience, household size, land area, tenancy status, ownership of tube-well, access to market information, information on weather forecasting and extension all influence the farmers' choice of adaptation measures. Results also indicate that adaptation to climate change is constrained by several factors such as lack of information; lack of money; resource constraint and shortage of irrigation water in the study area. Findings of the study suggest the need of greater investment in farmer education and improved institutional setup for climate change adaptation to improve farmers' wellbeing.

Impact of a simplified in situ protocol on enamel loss after erosive challenge

PubMed Central

Buzalaf, Marília Afonso Rabelo; Oliveira, Thais Marchini; Honório, Heitor Marques; Cruvinel, Thiago

2018-01-01

This study investigated the effect of the period of use and location of intraoral appliances on enamel surface loss. This randomized, single blind in situ study was conducted in 2 crossover phases based on the period of use, in which maxillary and mandibular appliances were simultaneously worn. Bovine enamel blocks (n = 120) were randomly divided among the studied groups by surface hardness. In each phase, fifteen volunteers used one maxillary appliance and two mandibular appliances for 5 days. Erosive challenge was performed 4X/day by immersion in 0.01 M HCL for 2 minutes. In the continuous phase, the intraoral appliances were worn for 20 hours. In the intermittent phase the appliances were worn for 8 hours and 30 minutes. Enamel loss was determined profilometrically. The discomfort of use of the appliances were evaluated in a questionnaire. Data were analyzed by two-way ANOVA/Tukey’s test and chi-square test (p<0.05). The maxillary appliance promoted higher enamel loss compared to the mandibular one (p<0.001). Intermittent use of appliances resulted in similar enamel loss to the continuous one (p = 0.686). All volunteers preferred to use the maxillary appliance in an intermittent regimen. The intermittent use of maxillary appliance is a simplified reliable protocol appropriated for in situ erosion studies in enamel. PMID:29734362

Removable orthodontic appliances: new perspectives on capabilities and efficiency.

PubMed

Hamid Zafarmand, A; Mahdi Zafarmand, M

2013-06-01

Removable appliances are a dependable choice for many patients but like all orthodontic appliances, they have some limitations in use. Patient selection and appropriate appliance design are two key factors for success. Many patients, especially adults, prefer intra-oral appliances to extra-oral devices. Sometimes a removable intra-oral appliance can solve a dental problem in a shorter period of time compared to fixed treatment, and this has also been repeatedly seen in molar distalisation. From the interceptive perspective, the appliance can prevent or alleviate an impending crowding for erupting permanent incisors. This article describes 5 patients with different orthodontic problems: impending crowding for erupting upper canine with 2 approaches, provision of space for upper cuspids, resolution of chronic attrition of anterior teeth, relief of space shortage for upper canines eruption, and reduction of excess overjet. All subjects were treated with removable appliances of various designs.

JPRS Report, Science & Technology. Japan: Economic Planning Agency Technology Forecast to the Year 2010.

DTIC Science & Technology

1991-11-17

are several concrete examples of how these affect application. (1) For the development and spread of solar photoelectric power generation, under the...technician in charge of each generator. In order to promote the installation of solar cells at various households and businesses, the relevant laws must be...products from microorganisms ’ Solar photoelectric power Communications satellites Skyscrapers Alone in 1st Tied for 1st 10 Years Ago Present !i

The Evolving Urban Community and Military Installations: A Dynamic Spatial Decision Support System for Sustainable Military Communities

DTIC Science & Technology

2007-01-01

focus on identifying growth by income and housing costs. These, and other models are focused on the city itself and deal with growth over the course...2. This model employs a set of econometric models to project future population, household, and employment. The landscape is gridded into one... model in LEAM (LEAMecon) forecasts changes in output, employment and income over time based on changes in the market, technology, productivity and

Probabilistic seasonal Forecasts to deterministic Farm Leve Decisions: Innovative Approach

NASA Astrophysics Data System (ADS)

Mwangi, M. W.

2015-12-01

Climate change and vulnerability are major challenges in ensuring household food security. Climate information services have the potential to cushion rural households from extreme climate risks. However, most the probabilistic nature of climate information products is not easily understood by majority of smallholder farmers. Despite the probabilistic nature, climate information have proved to be a valuable climate risk adaptation strategy at the farm level. This calls for innovative ways to help farmers understand and apply climate information services to inform their farm level decisions. The study endeavored to co-design and test appropriate innovation systems for climate information services uptake and scale up necessary for achieving climate risk development. In addition it also determined the conditions necessary to support the effective performance of the proposed innovation system. Data and information sources included systematic literature review, secondary sources, government statistics, focused group discussions, household surveys and semi-structured interviews. Data wasanalyzed using both quantitative and qualitative data analysis techniques. Quantitative data was analyzed using the Statistical Package for Social Sciences (SPSS) software. Qualitative data was analyzed using qualitative techniques, which involved establishing the categories and themes, relationships/patterns and conclusions in line with the study objectives. Sustainable livelihood, reduced household poverty and climate change resilience were the impact that resulted from the study.

A randomized controlled trial of self-perceived pain, discomfort, and impairment of jaw function in children undergoing orthodontic treatment with fixed or removable appliances.

PubMed

Wiedel, Anna-Paulina; Bondemark, Lars

2016-03-01

To compare patients' perceptions of fixed and removable appliance therapy for correction of anterior crossbite in the mixed dentition, with special reference to perceived pain, discomfort, and impairment of jaw function. Sixty-two patients with anterior crossbite and functional shift were recruited consecutively and randomized for treatment with fixed appliances (brackets and archwires) or removable appliances (acrylic plates and protruding springs). A questionnaire, previously found to be valid and reliable, was used for evaluation at the following time points: before appliance insertion, on the evening of the day of insertion, every day/evening for 7 days after insertion, and at the first and second scheduled appointments (after 4 and 8 weeks, respectively). Pain and discomfort intensity were higher for the first 3 days for the fixed appliance. Pain and discomfort scores overall peaked on day 2. Adverse effects on school and leisure activities were reported more frequently in the removable than in the fixed appliance group. The fixed appliance group reported more difficulty eating different kinds of hard and soft food, while the removable appliance group experienced more speech difficulties. No significant intergroup difference was found for self-estimated disturbance of appearance between the appliances. The general levels of pain and discomfort were low to moderate in both groups. There were some statistically significant differences between the groups, but these were only minor and with minor clinical relevance. As both appliances were generally well accepted by the patients, either fixed or removable appliance therapy can be recommended.

38 CFR 17.150 - Prosthetic and similar appliances.

Code of Federal Regulations, 2010 CFR

2010-07-01

... appliances. 17.150 Section 17.150 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.150 Prosthetic and similar appliances... appliances including invalid lifts and therapeutic and rehabilitative devices, and special clothing made...

Non-extraction treatment of severe crowding with pendulum appliance.

PubMed

Gandikota, Chandrasekhar; Venkata, Yudhister Palla; Challa, Padmalatha; Juvvadi, Shubhaker Rao

2013-07-01

An extraction case was planned for non-extraction treatment using pendulum appliance and the effect of appliance was evaluated in a 14-year-old girl with a severe maxillary and mandibular crowding followed by non-extraction fixed appliance preadjusted edgewise appliance mechanotherapy. Total treatment time was for 22 months. The obtuse nasolabial angle was maintained intact. Correction of crowding, co-ordinated arch forms was achieved with molar distalization. The impetus on soft-tissue paradigm is stressed in this case report and pendulum appliance can indeed boost our clinical acumen and swing our priorities toward non-extraction treatment.

A comparative study of two-piece ostomy appliances.

PubMed

Welser, Marion; Riedlinger, Inge; Prause, Ulla

The quality of life of people with a stoma may be affected by peristomal skin disorders and by frequent unplanned changes of ostomy appliances due to problems with those appliances. The aim of this study was to evaluate two new, two-piece ostomy appliances with mechanical couplings (both from the SenSura range by Coloplast) and their ability to address areas that may be important to the quality of life of people with stomas, including appliance changes, stool seepage and overfilling. The study design featured two comparative, crossover, randomized multi-centre studies that were conducted in Germany. The SenSura appliances were evaluated against established reference appliances. Seventy-three individuals with a colostomy (closed-end appliances) and 75 individuals with an ileostomy (drainable appliances) participated in the studies. The participants tested 4-6 flanges of each type within a maximum period of two weeks. The results demonstrated that there was less seepage of stool observed under the SenSura flange when it was removed (p<0.05). Also, there were fewer unplanned changes (p<0.0005) seen with SenSura than with the reference appliances. The SenSura flanges had better adhesion and flexibility and were easier to remove than the references (p<0.0005), and they had greater resistance to erosion (p<0.05). In conclusion, SenSura performed better than the reference appliances on quality of life indicators - there were fewer unplanned changes and less seepage of stool was observed in patients using the SenSura products.

A systematic review on the effectiveness of titratable over nontitratable mandibular advancement appliances for sleep apnea.

PubMed

Sivaramakrishnan, Gowri; Sridharan, Kannan

2017-01-01

Mandibular advancement appliances are being tested for use in patients with obstructive sleep apnea (OSA). However, the effectiveness of titration of these appliances does not have conclusive evidence. Systematic reviews help us to compile all available clinical evidence using statistical principles. Hence, the aim of this systematic review is to identify the effectiveness of titratable over nontitratable mandibular advancement appliances in patients with mild to moderate OSA. This review objective is to identify if titration of these appliances produce significant benefits over fixed appliances. Electronic databases were searched to identify eligible studies based on set inclusion criteria. Data extraction form was created and the data were extracted. The participants were mild to moderate OSA patients who received mandibular advancement appliances. Studies included a comparison between titratable and nontitratable mandibular advancement appliance. Of the five included studies, three were observational and two were a randomized trial. All these studies were conducted in adults. The outcome attributes were polysomnographic readings and apnea-hypopnea index (AHI). A significant heterogeneity was seen between the eligible studies and hence a meta-analysis could not be performed. The results from this systematic review did not show significant advantages of titratable appliances, although titratable appliances performed better from individual studies as regards to reduction in AHI and polysomnography. The reason is the lack of sufficient clinical trials on the same. More high quality randomized controlled trials comparing titratable and fixed appliances have to be initiated to get to conclusive evidence.

14 CFR 3.5 - Statements about products, parts, appliances and materials.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., appliances and materials. 3.5 Section 3.5 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION DEFINITIONS GENERAL REQUIREMENTS § 3.5 Statements about products, parts, appliances... product, part, appliance or material. (b) Prohibition against fraudulent and intentionally false...

78 FR 3854 - Appliance Standards and Rulemaking Federal Advisory Committee (ASRAC)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-17

... DEPARTMENT OF ENERGY 10 CFR Chapter II Appliance Standards and Rulemaking Federal Advisory... Appliance Standards and Rulemaking Federal Advisory Committee (ASRAC). The Federal Advisory Committee Act... the Energy Department on the development of standards and test procedures for residential appliances...

Crew appliance concepts. Volume 5, appendix C: Modular space station appliances supporting engineering data

NASA Technical Reports Server (NTRS)

Proctor, B. W.; Reysa, R. P.; Russell, D. J.

1975-01-01

Housekeeping, off-duty, and medical data concerning the appliances considered for the space station are presented. Appliance functions analyzed include: cleanup, collection, processing and storage of refuse; crew entertainment and physical exercise, and the autoclaves and ergometers.

A comparison between indirect and objective wear-time assessment of removable orthodontic appliances.

PubMed

Schott, Timm C; Meyer-Gutknecht, Hannes; Mayer, Nicolai; Weber, Joachim; Weimer, Katja

2017-04-01

Patients do not always adhere to the wear times prescribed for removable orthodontic appliances. We evaluated the validity and usability of indirect wear-time assessment methods by comparing wear-time estimates with microelectronically measured wear times in patients with removable orthodontic appliances. Wear times of 33 expansion plates, 34 functional appliances, and 42 retention plates of patients aged 6-20 years (12.3±2.9 years, 50.5% female) were indirectly determined by practitioners using a questionnaire assessing five parameters on a 5-point Likert scale: appliance handling, appliance appearance, bite shift, tooth movement, and appliance fit. The perceived difficulty in assessing each parameter was rated. Actual wear times were evaluated with microelectronic sensors in the appliances. Regression analyses revealed that practitioners' decisions about wear times varied depending on the type of appliance and criteria used, with only one standard criterion best predicting estimated wear time for each appliance. Different standard criteria were better predictors of measured wear time: 22.3% of wear-time variability was explained by expansion plate appearance, 31.2% by functional appliance handling, and 18.8% by retainer fitting. However, practitioners rated the difficulty of assessment in most cases as 'easy'. The study was not double blinded for technical reasons, and practitioners may have considered the evaluation criteria more carefully than in normal daily practice. Practitioners' decisions about wear times based on standard criteria strongly vary depending on the type of appliance and criteria used. © The Author 2016. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

Validation of numerical model for cook stove using Reynolds averaged Navier-Stokes based solver

NASA Astrophysics Data System (ADS)

Islam, Md. Moinul; Hasan, Md. Abdullah Al; Rahman, Md. Mominur; Rahaman, Md. Mashiur

2017-12-01

Biomass fired cook stoves, for many years, have been the main cooking appliance for the rural people of developing countries. Several researches have been carried out to the find efficient stoves. In the present study, numerical model of an improved household cook stove is developed to analyze the heat transfer and flow behavior of gas during operation. The numerical model is validated with the experimental results. Computation of the numerical model is executed the using non-premixed combustion model. Reynold's averaged Navier-Stokes (RaNS) equation along with the κ - ɛ model governed the turbulent flow associated within the computed domain. The computational results are in well agreement with the experiment. Developed numerical model can be used to predict the effect of different biomasses on the efficiency of the cook stove.

The Energy - Water Connection: Can We Sustain Critical Resources and Make them Reliable, Affordable, and Environmentally Sound?(LBNL Summer Lecture Series)

ScienceCinema

McMahon, Jim

2018-05-16

Summer Lecture Series 2006: Jim McMahon of Berkeley Lab's Environmental Energy Technologies Division (EETD) is head of the Energy Analysis Department in EETD, which provides technical analysis to the Department of Energy on things like energy efficiency appliance standards. McMahon and his colleagues helped the nation save tens of billions of dollars in energy costs since the standards program began. Now his Water-Energy Technology Team (WETT) is applying its expertise to the linked problem of energy and water. Each of us requires more than 500 gallons per person per day for food production, plus an additional 465 gallons to produce household electricity. WETT hopes to mine some of the numerous opportunities to save energy and water by applying new technologies.

A novel CUSUM-based approach for event detection in smart metering

NASA Astrophysics Data System (ADS)

Zhu, Zhicheng; Zhang, Shuai; Wei, Zhiqiang; Yin, Bo; Huang, Xianqing

2018-03-01

Non-intrusive load monitoring (NILM) plays such a significant role in raising consumer awareness on household electricity use to reduce overall energy consumption in the society. With regard to monitoring low power load, many researchers have introduced CUSUM into the NILM system, since the traditional event detection method is not as effective as expected. Due to the fact that the original CUSUM faces limitations given the small shift is below threshold, we therefore improve the test statistic which allows permissible deviation to gradually rise as the data size increases. This paper proposes a novel event detection and corresponding criterion that could be used in NILM systems to recognize transient states and to help the labelling task. Its performance has been tested in a real scenario where eight different appliances are connected to main line of electric power.

77 FR 15745 - Appliance Standards and Rulemaking Federal Advisory Committee (ASRAC): Correction

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-16

... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy Appliance Standards and... Energy, Department of Energy. ACTION: Notice of Establishment of the Appliance Standards and Rulemaking... Establishment of the Appliance Standards and Rulemaking Federal Advisory Committee (ASRAC) and Solicitation of...

24 CFR 3280.707 - Heat producing appliances.

Code of Federal Regulations, 2011 CFR

2011-04-01

... URBAN DEVELOPMENT MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARDS Heating, Cooling and Fuel Burning... oil burning comfort heating appliances shall have a flue loss of not more than 25 percent, and a...) Fuel-burning heat-producing appliances and refrigeration appliances, except ranges and ovens, shall be...

Magnetic fields from electric toothbrushes promote corrosion in orthodontic stainless steel appliances but not in titanium appliances.

PubMed

Kameda, Takashi; Ohkuma, Kazuo; Oda, Hirotake; Sano, Natsuki; Batbayar, Nomintsetseg; Terashima, Yukari; Sato, Soh; Terada, Kazuto

2013-01-01

Electric toothbrushes are widely used, and their electric motors have been reported to produce low-frequency electromagnetic fields that induced electric currents in metallic objects worn by the users. In this study, we showed that electric toothbrushes generated low-frequency magnetic fields (MFs) and induced electric currents in orthodontic appliances in artificial saliva (AS), which accelerated corrosion in stainless steel (SUS) appliances, but not in titanium (Ti) appliances; the corrosion was evaluated by using an inductively coupled plasma-optical emission spectrometer and a three-dimensional laser confocal microscope. The pH of AS used for appliance immersion did not change during or after MF exposure. These results suggested that MF-induced currents from electric toothbrushes could erode SUS appliances, but not Ti appliances, because of their high corrosion potentials. Further studies are required to clarify the mechanisms of metallic corrosion by induced currents in dental fields, which may trigger metal allergies in patients.

A randomised titrated crossover study comparing two oral appliances in the treatment for mild to moderate obstructive sleep apnoea/hypopnoea syndrome.

PubMed

Zhou, J; Liu, Y H

2012-12-01

The objective of this study was to compare the efficiency of two oral appliances in patients with mild to moderate obstructive sleep apnoea/hypopnoea syndrome (OSAHS) by the analysis of objective and subjective evaluations and measurement of upper airway parameter. A randomised crossover design trial was carried out on 16 patients with OSAHS. Two different types of oral appliances were tested in each patient, a one-piece monoblock and the SILENT NITE(®) (GlideWell Laboratories, Newport Beach, CA, USA), a two-piece appliance. Each oral appliance needed to be worn for two 3-month periods separated by a 2-week wash-out period in between. The objective and subjective efficiency and upper airway parameters associated with the oral appliances were assessed. One-way analysis of variance (anova) test was performed to compare the changes in upper airway morphology and the treatment efficiency between the appliances. The monoblock and SILENT NITE(®) (GlideWell Laboratories) appliances reduced Apnoea Hypopnoea Index (AHI) from 26·38 ± 4·13 to 7·58 ± 2·28 (P < 0·001) and 8·87 ± 2·88 (P < 0·001), respectively. The monoblock appliance was statistically more efficient in reducing AHI and Apnoea Index (AI) than the SILENT NITE(®) (GlideWell Laboratories) (P < 0·05). The scores on Epworth's Sleepiness Scale (ESS) and Snoring Scale (SS) were improved significantly by both appliances. The upper airway spaces showed considerable enlargement by both mandibular advancement appliances (MAAs) (P < 0·05), while no significant differences were found between the two appliances (P > 0·05). Both MAAs showed good efficacy in the treatment for mild to moderate OSAHS. Use of the monoblock appliance should be considered when patients with OSAHS choose MAA treatment, as it was more efficient in reducing the AHI and AI compared to the two-piece appliance and was preferred by most patients. Long-term efficiency should be evaluated in future prospective studies. © 2012 Blackwell Publishing Ltd.

The Extent, Nature and Environmental Health Implications of Cottage Industries in Johannesburg, South Africa

PubMed Central

Teare, June; Kootbodien, Tahira; Naicker, Nisha; Mathee, Angela

2015-01-01

Cottage industries comprise a sub-group of informal sector income generation activities which are conducted in the home environment and organized around families or households. Cottage industry workers may be at risk of exposure to harmful substances associated with their work, and given the lack of separation of cottage industry activities from living spaces, their families and neighbors may similarly be at risk of exposure. This study was undertaken to determine the extent and nature of cottage industries in five neighborhoods in Johannesburg (South Africa) A cross-sectional survey was conducted across five communities in Johannesburg in 2012. Data on metal-related cottage industry activities were collected through the administration of a pre-structured questionnaire. Metal-related cottage industry activities were defined as car repairs, spray painting, scrap metal recycling, electrical appliance repairs, welding, hairdressing and metal jewelry making. One fifth of the households interviewed were operating one or more cottage industries associated with the use of toxic substances. Therefore, the potential exists for associated ill health effects in a considerable proportion of the population. Further research is needed to fully assess exposure to the harmful aspects of cottage industry, as are scaled up campaigns to increase awareness of the risks and correct handling of toxic substances. PMID:25664698

The extent, nature and environmental health implications of cottage industries in Johannesburg, South Africa.

PubMed

Teare, June; Kootbodien, Tahira; Naicker, Nisha; Mathee, Angela

2015-02-05

Cottage industries comprise a sub-group of informal sector income generation activities which are conducted in the home environment and organized around families or households. Cottage industry workers may be at risk of exposure to harmful substances associated with their work, and given the lack of separation of cottage industry activities from living spaces, their families and neighbors may similarly be at risk of exposure. This study was undertaken to determine the extent and nature of cottage industries in five neighborhoods in Johannesburg (South Africa) A cross-sectional survey was conducted across five communities in Johannesburg in 2012. Data on metal-related cottage industry activities were collected through the administration of a pre-structured questionnaire. Metal-related cottage industry activities were defined as car repairs, spray painting, scrap metal recycling, electrical appliance repairs, welding, hairdressing and metal jewelry making. One fifth of the households interviewed were operating one or more cottage industries associated with the use of toxic substances. Therefore, the potential exists for associated ill health effects in a considerable proportion of the population. Further research is needed to fully assess exposure to the harmful aspects of cottage industry, as are scaled up campaigns to increase awareness of the risks and correct handling of toxic substances.

Functional unit, technological dynamics, and scaling properties for the life cycle energy of residences.

PubMed

Frijia, Stephane; Guhathakurta, Subhrajit; Williams, Eric

2012-02-07

Prior LCA studies take the operational phase to include all energy use within a residence, implying a functional unit of all household activities, but then exclude related supply chains such as production of food, appliances, and household chemicals. We argue that bounding the functional unit to provision of a climate controlled space better focuses the LCA on the building, rather than activities that occur within a building. The second issue explored in this article is how technological change in the operational phase affects life cycle energy. Heating and cooling equipment is replaced at least several times over the lifetime of a residence; improved efficiency of newer equipment affects life cycle energy use. The third objective is to construct parametric models to describe LCA results for a family of related products. We explore these three issues through a case study of energy use of residences: one-story and two-story detached homes, 1,500-3,500 square feet in area, located in Phoenix, Arizona, built in 2002 and retired in 2051. With a restricted functional unit and accounting for technological progress, approximately 30% of a building's life cycle energy can be attributed to materials and construction, compared to 0.4-11% in previous studies.

Circumventing Imprecise Geometric Information and Development of a Unified Modeling Technique for Various Flow Regimes in Capillary Tubes

NASA Astrophysics Data System (ADS)

Abbasi, Bahman

2012-11-01

Owing to their manufacturability and reliability, capillary tubes are the most common expansion devices in household refrigerators. Therefore, investigating flow properties in the capillary tubes is of immense appeal in the said business. The models to predict pressure drop in two-phase internal flows invariably rely upon highly precise geometric information. The manner in which capillary tubes are manufactured makes them highly susceptible to geometric imprecisions, which renders geometry-based models unreliable to the point of obsoleteness. Aware of the issue, manufacturers categorize capillary tubes based on Nitrogen flow rate through them. This categorization method presents an opportunity to substitute geometric details with Nitrogen flow data as the basis for customized models. The simulation tools developed by implementation of this technique have the singular advantage of being applicable across flow regimes. Thus the error-prone process of identifying compatible correlations is eliminated. Equally importantly, compressibility and chocking effects can be incorporated in the same model. The outcome is a standalone correlation that provides accurate predictions, regardless of any particular fluid or flow regime. Thereby, exploratory investigations for capillary tube design and optimization are greatly simplified. Bahman Abbasi, Ph.D., is Lead Advanced Systems Engineer at General Electric Appliances in Louisville, KY. He conducts research projects across disciplines in the household refrigeration industry.

38 CFR 17.153 - Training in the use of appliances.

Code of Federal Regulations, 2010 CFR

2010-07-01

... appliances. 17.153 Section 17.153 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.153 Training in the use of appliances. Beneficiaries supplied prosthetic and similar appliances will be additionally entitled to fitting and training...

Speech Appliances in the Treatment of Phonological Disorders.

ERIC Educational Resources Information Center

Ruscello, Dennis M.

1995-01-01

This article addresses the rationale for and issues related to the use of speech appliances, especially a removable speech appliance that positions the tongue to produce the correct /r/ phoneme. Research results suggest that this appliance was successful with a large group of clients. (Author/DB)

78 FR 37995 - Appliance Standards and Rulemaking Federal Advisory Committee: Notice of Open Teleconference/Webinar

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-25

...-2013-BT-NOC-0023] Appliance Standards and Rulemaking Federal Advisory Committee: Notice of Open...: Notice of open Teleconference/Webinar. SUMMARY: This document announces a meeting of the Appliance... appliances and commercial equipment, certification and enforcement of standards, and product labeling...

46 CFR 188.27-1 - Lifesaving appliances and arrangements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Lifesaving appliances and arrangements. 188.27-1 Section 188.27-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 188.27-1 Lifesaving appliances and...

46 CFR 188.27-1 - Lifesaving appliances and arrangements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Lifesaving appliances and arrangements. 188.27-1 Section 188.27-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 188.27-1 Lifesaving appliances and...

46 CFR 188.27-1 - Lifesaving appliances and arrangements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Lifesaving appliances and arrangements. 188.27-1 Section 188.27-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 188.27-1 Lifesaving appliances and...

46 CFR 188.27-1 - Lifesaving appliances and arrangements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Lifesaving appliances and arrangements. 188.27-1 Section 188.27-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 188.27-1 Lifesaving appliances and...

Determination of appropriate DC voltage for switched mode power supply (SMPS) loads

NASA Astrophysics Data System (ADS)

Setiawan, Eko Adhi; Setiawan, Aiman; Purnomo, Andri; Djamal, Muchlishah Hadi

2017-03-01

Nowadays, most of modern and efficient household electronic devices operated based on Switched Mode Power Supply (SMPS) technology which convert AC voltage from the grid to DC voltage. Based on theory and experiment, SMPS loads could be supplied by DC voltage. However, the DC voltage rating to energize electronic home appliances is not standardized yet. This paper proposed certain method to determine appropriate DC voltage, and investigated comparison of SMPS power consumption which is supplied from AC and DC voltage. To determine the appropriate DC voltage, lux value of several lamps which have same specification energized by using AC voltage and the results is using as reference. Then, the lamps were supplied by various DC voltage to obtain the trends of the lux value to the applied DC voltage. After that, by using the trends and the reference lux value, the appropriate DC voltage can be determined. Furthermore, the power consumption on home appliances such as mobile phone, laptop and personal computer by using AC voltage and the appropriate DC voltage were conducted. The results show that the total power consumption of AC system is higher than DC system. The total power (apparent power) consumed by the lamp, mobile phone and personal computer which operated in 220 VAC were 6.93 VA, 34.31 VA and 105.85 VA respectively. On the other hand, under 277 VDC the load consumption were 5.83 W, 19.11 W and 74.46 W respectively.

46 CFR 167.15-28 - Inspection of lifesaving appliances and arrangements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-28 Inspection of lifesaving appliances and arrangements. The inspection of lifesaving appliances and arrangements must be in accordance with the... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection of lifesaving appliances and arrangements...

46 CFR 78.47-45 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to...-45 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with subchapter W...

33 CFR 150.506 - When must the operator service inflatable lifesaving appliances and marine evacuation systems?

Code of Federal Regulations, 2010 CFR

2010-07-01

... inflatable lifesaving appliances and marine evacuation systems? 150.506 Section 150.506 Navigation and...: OPERATIONS Emergency and Specialty Equipment Inflatable Lifesaving Appliances § 150.506 When must the operator service inflatable lifesaving appliances and marine evacuation systems? (a) The operator must...

42 CFR 409.14 - Supplies, appliances, and equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Supplies, appliances, and equipment. 409.14 Section... Hospital Services § 409.14 Supplies, appliances, and equipment. (a) Except as specified in paragraph (b) of this section, Medicare pays for supplies, appliances, and equipment as inpatient hospital or inpatient...

14 CFR 183.63 - Continuing requirements: Products, parts or appliances.

Code of Federal Regulations, 2010 CFR

2010-01-01

... appliances. 183.63 Section 183.63 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Designation Authorization § 183.63 Continuing requirements: Products, parts or appliances. For any approval or certificate for a product, part or appliance issued under the authority of this subpart, or under the...

46 CFR 108.597 - Line-throwing appliance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Line-throwing appliance. 108.597 Section 108.597... AND EQUIPMENT Lifesaving Equipment § 108.597 Line-throwing appliance. (a) General. Each unit in international service must have a line-throwing appliance that is approved under approval series 160.040. Each...

33 CFR 150.507 - How must the operator service inflatable lifesaving appliances?

Code of Federal Regulations, 2010 CFR

2010-07-01

... inflatable lifesaving appliances? 150.507 Section 150.507 Navigation and Navigable Waters COAST GUARD... Specialty Equipment Inflatable Lifesaving Appliances § 150.507 How must the operator service inflatable lifesaving appliances? (a) The operator must service each inflatable liferaft according to 46 CFR subpart 160...

46 CFR 111.77-1 - Overcurrent protection.

Code of Federal Regulations, 2010 CFR

2010-10-01

...-GENERAL REQUIREMENTS Appliances and Appliance Circuits § 111.77-1 Overcurrent protection. If a circuit supplies only one appliance or device, the rating or setting of the branch circuit overcurrent device must not be more than 150 percent of the rating of the appliance or device, or 15 amperes, whichever is...

ELECTRICAL APPLIANCE SERVICEMAN, SUGGESTED GUIDE FOR A TRAINING COURSE.

ERIC Educational Resources Information Center

LOVE, L. CARL; RONEY, MAURICE W.

THE PURPOSE OF THIS GUIDE IS TO AID IN PLANNING AND DEVELOPING A COURSE FOR TRAINING ELECTRICAL APPLIANCE SERVICEMEN. OUTLINES (ONE PAGE EACH) COVER -- (1) RELATED INSTRUCTION, (2) FUNDAMENTALS OF ELECTRICITY, (3) BASIC CONTROLS AND ELECTRONIC COMPONENTS, (4) RESISTANCE HEATING APPLIANCES, (5) MOTORS FOR ELECTRIC APPLIANCES, (6) MOTOR DRIVEN…

14 CFR 43.7 - Persons authorized to approve aircraft, airframes, aircraft engines, propellers, appliances, or...

Code of Federal Regulations, 2013 CFR

2013-01-01

..., airframes, aircraft engines, propellers, appliances, or component parts for return to service after... Administrator, may approve an aircraft, airframe, aircraft engine, propeller, appliance, or component part for..., airframe, aircraft engine, propeller, appliance, or component part for return to service as provided in...

14 CFR 43.7 - Persons authorized to approve aircraft, airframes, aircraft engines, propellers, appliances, or...

Code of Federal Regulations, 2012 CFR

2012-01-01

..., airframes, aircraft engines, propellers, appliances, or component parts for return to service after... Administrator, may approve an aircraft, airframe, aircraft engine, propeller, appliance, or component part for..., airframe, aircraft engine, propeller, appliance, or component part for return to service as provided in...

14 CFR 43.7 - Persons authorized to approve aircraft, airframes, aircraft engines, propellers, appliances, or...

Code of Federal Regulations, 2011 CFR

2011-01-01

..., airframes, aircraft engines, propellers, appliances, or component parts for return to service after... Administrator, may approve an aircraft, airframe, aircraft engine, propeller, appliance, or component part for..., airframe, aircraft engine, propeller, appliance, or component part for return to service as provided in...

14 CFR 43.7 - Persons authorized to approve aircraft, airframes, aircraft engines, propellers, appliances, or...

Code of Federal Regulations, 2014 CFR

2014-01-01

..., airframes, aircraft engines, propellers, appliances, or component parts for return to service after... Administrator, may approve an aircraft, airframe, aircraft engine, propeller, appliance, or component part for..., airframe, aircraft engine, propeller, appliance, or component part for return to service as provided in...

Crew appliance concepts. Volume 4, appendix C: Modular space station appliances supporting engineering data. [food management and personal hygiene

NASA Technical Reports Server (NTRS)

Proctor, B. W.; Reysa, R. P.; Russell, D. J.

1975-01-01

Data collected for the appliances considered for the space station are presented along with plotted and tabulated trade study results for each appliance. The food management, and personal hygiene data are applicable to a six-man mission of 180-days.

Habit Breaking Appliance for Multiple Corrections

PubMed Central

Abraham, Reji; Kamath, Geetha; Sodhi, Jasmeet Singh; Sodhi, Sonia; Rita, Chandki; Sai Kalyan, S.

2013-01-01

Tongue thrusting and thumb sucking are the most commonly seen oral habits which act as the major etiological factors in the development of dental malocclusion. This case report describes a fixed habit correcting appliance, Hybrid Habit Correcting Appliance (HHCA), designed to eliminate these habits. This hybrid appliance is effective in less compliant patients and if desired can be used along with the fixed orthodontic appliance. Its components can act as mechanical restrainers and muscle retraining devices. It is also effective in cases with mild posterior crossbites. PMID:24198976

Meteorology for public

NASA Astrophysics Data System (ADS)

Špoler Čanić, Kornelija; Rasol, Dubravka; Milković, Janja

2013-04-01

The Meteorological and Hydrological Service in Croatia (MHSC) is, as a public service, open to and concentrated on public. The organization of visits to the MHSC for groups started in 1986. The GLOBE program in Croatia started in 1995 and after that interest for the group tours at the MHSC has increased. The majority of visitors are school and kindergarten children, students and groups of teachers. For each group tour we try to prepare the content that is suitable for the age and interest of a group. Majority of groups prefer to visit the meteorological station where they can see meteorological instruments and learn how they work. It is organized as a little workshop, where visitors can ask questions and discuss with a guide not only about the meteorological measurements but also about weather and climate phenomena they are interested in. Undoubtedly the highlight of a visit is the forecaster's room where visitors can talk to the forecasters (whom they can also see giving a weather forecast on the national TV station) and learn how weather forecasts are made. Sometimes we offer to visitors to make some meteorological experiments but that is still not in a regular program of the group tours due to the lack of performing space. Therefore we give them the instructions for making instruments and simulations of meteorological phenomena from household items. Visits guides are meteorologists with profound experience in the popularization of science.

Farmers' perceptions of and adaptation strategies to climate change and their determinants: the case of Punjab province, Pakistan

NASA Astrophysics Data System (ADS)

Abid, M.; Scheffran, J.; Schneider, U. A.; Ashfaq, M.

2015-05-01

Climate change is a global environmental threat to all economic sectors, particularly the agricultural sector. Pakistan is one of the countries negatively affected by climate change due to its high exposure to extreme events and low adaptive capacity. In Pakistan, farmers are the primary stakeholders in agriculture and are more at risk due to climate vulnerability. Based on farm household data from 450 households collected from three districts in three agroecological zones in the Punjab province of Pakistan, this study examines how farmers perceive climate change and how they adapt their farming in response to perceived changes in climate. The results demonstrate that awareness of climate change is widespread throughout the area, and farm households make adjustments to adapt their agriculture in response to climatic change. Overall 58% of the farm households adapted their farming to climate change. Changing crop varieties, changing planting dates, planting of shade trees and changing fertilizers were the main adaptation methods implemented by farm households in the study area. The results from the binary logistic model reveal that education, farm experience, household size, land area, tenancy status, ownership of a tube well, access to market information, information on weather forecasting and agricultural extension services all influence farmers' choices of adaptation measures. The results also indicate that adaptation to climate change is constrained by several factors such as lack of information, lack of money, resource constraints and shortage of irrigation water in the study area. Findings of the study suggest the need for greater investment in farmer education and improved institutional setup for climate change adaptation to improve farmers' wellbeing.

Microbiologically influenced corrosion of orthodontic metallic appliances.

PubMed

Kameda, Takashi; Oda, Hirotake; Ohkuma, Kazuo; Sano, Natsuki; Batbayar, Nomintsetseg; Terashima, Yukari; Sato, Soh; Terada, Kazuto

2014-01-01

Biocorrosion (microbiologically influenced corrosion; MIC) occur in aquatic habitats varying in nutrient content, temperature, stress and pH. The oral environment of organisms, including humans, should be one of the most hospitable for MIC. Corrosion of metallic appliances in the oral region is one cause of metal allergy in patients. In this study, an inductively coupled plasma-optical emission spectrometer revealed elution of Fe, Cr and Ni from stainless steel (SUS) appliances incubated with oral bacteria. Three-dimensional laser confocal microscopy also revealed that oral bacterial culture promoted increased surface roughness and corrosion pits in SUS appliances. The pH of the supernatant was lowered after co-culture of appliances and oral bacteria in any combinations, but not reached at the level of depassivation pH of their metallic materials. This study showed that Streptococcus mutans and Streptococcus sanguinis which easily created biofilm on the surfaces of teeth and appliances, did corrode orthodontic SUS appliances.

Crew appliance concepts. Volume 1, appendix A: Bibliography. [manned space shuttle orbiter environmental control and life support systems

NASA Technical Reports Server (NTRS)

Proctor, B. W.; Reysa, R. P.; Russell, D. J.

1975-01-01

A review of crew appliance related literature was made to provide background engineering information for development of conceptual appliance systems for the shuttle orbiter and the modular space station. From this review, a file containing abstracts of 299 appliance-related documents coded according to subject was developed along with a computerized bibliography of 682 references. Trade studies were conducted using information from these references to determine the optimum concepts to satisfy the shuttle and space station mission requirements. An appliance system was devised for each vehicle which has minimum impact to the respective environmental control system with the smallest possible weight, volume, and electrical penalty. Engineering parameters for each appliance concept considered are presented along with the total thermal and electrical loads and weight and volume penalties for each of the optimized appliance systems.

77 FR 21734 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-11

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-941] Certain Kitchen Appliance... duty order on certain kitchen appliance shelving and racks from the People's Republic of China (``PRC... Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary Results of...

46 CFR 133.170 - Line-throwing appliance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Line-throwing appliance. 133.170 Section 133.170... SYSTEMS Requirements for All OSVs § 133.170 Line-throwing appliance. (a) General. Each OSV must have a line-throwing appliance that is approved under approval series 160.031 or 160.040. (b) Stowage. The...

46 CFR 97.37-42 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to..., Etc. § 97.37-42 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with...

46 CFR 196.37-37 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to..., etc. § 196.37-37 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with...

14 CFR 21.617 - Issue of letters of TSO design approval: import appliances.

Code of Federal Regulations, 2010 CFR

2010-01-01

...: import appliances. 21.617 Section 21.617 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Order Authorizations § 21.617 Issue of letters of TSO design approval: import appliances. (a) A letter of TSO design approval may be issued for an appliance that is manufactured in a foreign country with...

Mountain Plains Learning Experience Guide: Appliance Repair. Course: Motor-Operated Appliances.

ERIC Educational Resources Information Center

Ziller, T.

One of two individualized courses included in an appliance repair curriculum, this course is designed to prepare students to operate, diagnose malfunctions, repair, and service motor operated appliances. The course is comprised of seven units: (1) Mixers and Blenders, (2) Vacuum Cleaners and Floor Polishers, (3) Washing Machines, (4) Garbage…

33 CFR 150.504 - When must the operator service and examine lifeboat and rescue boat launching appliances?

Code of Federal Regulations, 2012 CFR

2012-07-01

... and examine lifeboat and rescue boat launching appliances? 150.504 Section 150.504 Navigation and... and examine lifeboat and rescue boat launching appliances? (a) The operator must service launching appliances for lifeboats and rescue boats at intervals recommended in the manufacturer's instructions under...

33 CFR 150.504 - When must the operator service and examine lifeboat and rescue boat launching appliances?

Code of Federal Regulations, 2013 CFR

2013-07-01

... and examine lifeboat and rescue boat launching appliances? 150.504 Section 150.504 Navigation and... and examine lifeboat and rescue boat launching appliances? (a) The operator must service launching appliances for lifeboats and rescue boats at intervals recommended in the manufacturer's instructions under...

33 CFR 150.504 - When must the operator service and examine lifeboat and rescue boat launching appliances?

Code of Federal Regulations, 2010 CFR

2010-07-01

... and examine lifeboat and rescue boat launching appliances? 150.504 Section 150.504 Navigation and... and examine lifeboat and rescue boat launching appliances? (a) The operator must service launching appliances for lifeboats and rescue boats at intervals recommended in the manufacturer's instructions under...

33 CFR 150.504 - When must the operator service and examine lifeboat and rescue boat launching appliances?

Code of Federal Regulations, 2014 CFR

2014-07-01

... and examine lifeboat and rescue boat launching appliances? 150.504 Section 150.504 Navigation and... and examine lifeboat and rescue boat launching appliances? (a) The operator must service launching appliances for lifeboats and rescue boats at intervals recommended in the manufacturer's instructions under...

33 CFR 150.504 - When must the operator service and examine lifeboat and rescue boat launching appliances?

Code of Federal Regulations, 2011 CFR

2011-07-01

... and examine lifeboat and rescue boat launching appliances? 150.504 Section 150.504 Navigation and... and examine lifeboat and rescue boat launching appliances? (a) The operator must service launching appliances for lifeboats and rescue boats at intervals recommended in the manufacturer's instructions under...

Effect of occlusal appliances and clenching on the internally deranged TMJ space.

PubMed

Kuboki, T; Takenami, Y; Orsini, M G; Maekawa, K; Yamashita, A; Azuma, Y; Clark, G T

1999-01-01

Stabilization appliances and mandibular anterior repositioning appliances have been used to treat patients with internal derangement of the temporomandibular joint (TMJ) based on the assumption that these appliances work by decompressing the TMJ. The purpose of this study was to indirectly test this assumption. Bilateral TMJ tomograms of 7 subjects with unilateral anterior disc displacement without reduction (ADDwor) were taken during comfortable closure and during maximum clenching in maximum intercuspation; tomograms were also taken with the 2 types of occlusal appliances in use. Outlines of the condyle and the temporal fossa were automatically determined by an edge-detection protocol, and the minimum joint space dimension of the joints with and without ADDwor was automatically measured for each experimental condition as the outcome variable. Upon comfortable closure and maximum clenching, the minimum joint space dimensions of the ipsilateral and contralateral joints with the use of stabilization appliances and mandibular anterior repositioning appliances were not significantly different from those seen in maximum intercuspation. These findings do not indicate that these appliances induce an increase in joint space during closing and clenching in joints with ADDwor.

Class II malocclusion with complex problems treated with a novel combination of lingual orthodontic appliances and lingual arches.

PubMed

Yanagita, Takeshi; Nakamura, Masahiro; Kawanabe, Noriaki; Yamashiro, Takashi

2014-07-01

This case report describes a novel method of combining lingual appliances and lingual arches to control horizontal problems. The patient, who was 25 years of age at her first visit to our hospital with a chief complaint of crooked anterior teeth, was diagnosed with skeletal Class II and Angle Class II malocclusion with anterior deep bite, lateral open bite, premolar crossbite, and severe crowding in both arches. She was treated with premolar extractions and temporary anchorage devices. Conventionally, it is ideal to use labial brackets simultaneously with appliances, such as a lingual arch, a quad-helix, or a rapid expansion appliance, in patients with complex problems requiring horizontal, anteroposterior, and vertical control; however, this patient strongly requested orthodontic treatment with lingual appliances. A limitation of lingual appliances is that they cannot be used with other conventional appliances. In this report, we present the successful orthodontic treatment of a complex problem using modified lingual appliances that enabled combined use of a conventional lingual arch. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

The UK-DALE dataset, domestic appliance-level electricity demand and whole-house demand from five UK homes.

PubMed

Kelly, Jack; Knottenbelt, William

2015-01-01

Many countries are rolling out smart electricity meters. These measure a home's total power demand. However, research into consumer behaviour suggests that consumers are best able to improve their energy efficiency when provided with itemised, appliance-by-appliance consumption information. Energy disaggregation is a computational technique for estimating appliance-by-appliance energy consumption from a whole-house meter signal. To conduct research on disaggregation algorithms, researchers require data describing not just the aggregate demand per building but also the 'ground truth' demand of individual appliances. In this context, we present UK-DALE: an open-access dataset from the UK recording Domestic Appliance-Level Electricity at a sample rate of 16 kHz for the whole-house and at 1/6 Hz for individual appliances. This is the first open access UK dataset at this temporal resolution. We recorded from five houses, one of which was recorded for 655 days, the longest duration we are aware of for any energy dataset at this sample rate. We also describe the low-cost, open-source, wireless system we built for collecting our dataset.

A Bayesian spatio-temporal model for forecasting the prevalence of antibodies to Borrelia burgdorferi, causative agent of Lyme disease, in domestic dogs within the contiguous United States.

PubMed

Watson, Stella C; Liu, Yan; Lund, Robert B; Gettings, Jenna R; Nordone, Shila K; McMahan, Christopher S; Yabsley, Michael J

2017-01-01

This paper models the prevalence of antibodies to Borrelia burgdorferi in domestic dogs in the United States using climate, geographic, and societal factors. We then use this model to forecast the prevalence of antibodies to B. burgdorferi in dogs for 2016. The data available for this study consists of 11,937,925 B. burgdorferi serologic test results collected at the county level within the 48 contiguous United States from 2011-2015. Using the serologic data, a baseline B. burgdorferi antibody prevalence map was constructed through the use of spatial smoothing techniques after temporal aggregation; i.e., head-banging and Kriging. In addition, several covariates purported to be associated with B. burgdorferi prevalence were collected on the same spatio-temporal granularity, and include forestation, elevation, water coverage, temperature, relative humidity, precipitation, population density, and median household income. A Bayesian spatio-temporal conditional autoregressive (CAR) model was used to analyze these data, for the purposes of identifying significant risk factors and for constructing disease forecasts. The fidelity of the forecasting technique was assessed using historical data, and a Lyme disease forecast for dogs in 2016 was constructed. The correlation between the county level model and baseline B. burgdorferi antibody prevalence estimates from 2011 to 2015 is 0.894, illustrating that the Bayesian spatio-temporal CAR model provides a good fit to these data. The fidelity of the forecasting technique was assessed in the usual fashion; i.e., the 2011-2014 data was used to forecast the 2015 county level prevalence, with comparisons between observed and predicted being made. The weighted (to acknowledge sample size) correlation between 2015 county level observed prevalence and 2015 forecasted prevalence is 0.978. A forecast for the prevalence of B. burgdorferi antibodies in domestic dogs in 2016 is also provided. The forecast presented from this model can be used to alert veterinarians in areas likely to see above average B. burgdorferi antibody prevalence in dogs in the upcoming year. In addition, because dogs and humans can be exposed to ticks in similar habitats, these data may ultimately prove useful in predicting areas where human Lyme disease risk may emerge.

A Bayesian spatio-temporal model for forecasting the prevalence of antibodies to Borrelia burgdorferi, causative agent of Lyme disease, in domestic dogs within the contiguous United States

PubMed Central

Watson, Stella C.; Liu, Yan; Lund, Robert B.; Gettings, Jenna R.; Nordone, Shila K.; McMahan, Christopher S.

2017-01-01

This paper models the prevalence of antibodies to Borrelia burgdorferi in domestic dogs in the United States using climate, geographic, and societal factors. We then use this model to forecast the prevalence of antibodies to B. burgdorferi in dogs for 2016. The data available for this study consists of 11,937,925 B. burgdorferi serologic test results collected at the county level within the 48 contiguous United States from 2011-2015. Using the serologic data, a baseline B. burgdorferi antibody prevalence map was constructed through the use of spatial smoothing techniques after temporal aggregation; i.e., head-banging and Kriging. In addition, several covariates purported to be associated with B. burgdorferi prevalence were collected on the same spatio-temporal granularity, and include forestation, elevation, water coverage, temperature, relative humidity, precipitation, population density, and median household income. A Bayesian spatio-temporal conditional autoregressive (CAR) model was used to analyze these data, for the purposes of identifying significant risk factors and for constructing disease forecasts. The fidelity of the forecasting technique was assessed using historical data, and a Lyme disease forecast for dogs in 2016 was constructed. The correlation between the county level model and baseline B. burgdorferi antibody prevalence estimates from 2011 to 2015 is 0.894, illustrating that the Bayesian spatio-temporal CAR model provides a good fit to these data. The fidelity of the forecasting technique was assessed in the usual fashion; i.e., the 2011-2014 data was used to forecast the 2015 county level prevalence, with comparisons between observed and predicted being made. The weighted (to acknowledge sample size) correlation between 2015 county level observed prevalence and 2015 forecasted prevalence is 0.978. A forecast for the prevalence of B. burgdorferi antibodies in domestic dogs in 2016 is also provided. The forecast presented from this model can be used to alert veterinarians in areas likely to see above average B. burgdorferi antibody prevalence in dogs in the upcoming year. In addition, because dogs and humans can be exposed to ticks in similar habitats, these data may ultimately prove useful in predicting areas where human Lyme disease risk may emerge. PMID:28472096

Evaluation of Invisalign treatment effectiveness and efficiency compared with conventional fixed appliances using the Peer Assessment Rating index.

PubMed

Gu, Jiafeng; Tang, Jack Shengyu; Skulski, Brennan; Fields, Henry W; Beck, F Michael; Firestone, Allen R; Kim, Do-Gyoon; Deguchi, Toru

2017-02-01

The purpose of this retrospective case-control study was to compare the treatment effectiveness and efficiency of the Invisalign system with conventional fixed appliances in treating orthodontic patients with mild to moderate malocclusion in a graduate orthodontic clinic. Using the peer assessment rating (PAR) index, we evaluated pretreatment and posttreatment records of 48 Invisalign patients and 48 fixed appliances patients. The 2 groups of patients were controlled for general characteristics and initial severity of malocclusion. We analyzed treatment outcome, duration, and improvement between the Invisalign and fixed appliances groups. The average pretreatment PAR scores (United Kingdom weighting) were 20.81 for Invisalign and 22.79 for fixed appliances (P = 1.0000). Posttreatment weighted PAR scores between Invisalign and fixed appliances were not statistically different (P = 0.7420). On average, the Invisalign patients finished 5.7 months faster than did those with fixed appliances (P = 0.0040). The weighted PAR score reduction with treatment was not statistically different between the Invisalign and fixed appliances groups (P = 0.4573). All patients in both groups had more than a 30% reduction in the PAR scores. Logistic regression analysis indicated that the odds of achieving "great improvement" in the Invisalign group were 0.329 times the odds of achieving "great improvement" in the fixed appliances group after controlling for age (P = 0.0150). Our data showed that both Invisalign and fixed appliances were able to improve the malocclusion. Invisalign patients finished treatment faster than did those with fixed appliances. However, it appears that Invisalign may not be as effective as fixed appliances in achieving "great improvement" in a malocclusion. This study might help clinicians to determine appropriate patients for Invisalign treatment. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Comparison of Adjustable and Fixed Oral Appliances for the Treatment of Obstructive Sleep Apnea

PubMed Central

Lettieri, Christopher J.; Paolino, Nathalie; Eliasson, Arn H.; Shah, Anita A.; Holley, Aaron B.

2011-01-01

Study Objectives: To compare the efficacy of adjustable and fixed oral appliances for the treatment of OSA. Methods: Retrospective review of consecutive patients with OSA treated with either adjustable or fixed oral appliances. Polysomnography was conducted before and during therapy. Effective treatment was defined as an apnea-hypopnea index (AHI) < 5 events/h or < 10 events/h with resolution of sleepiness (Epworth < 10). We compared efficacy rates between fixed and adjustable appliances and sought to identify factors associated with greater success. Results: We included 805 patients, 602 (74.8%) treated with an adjustable and 203 (25.2%) a fixed oral appliances. Among the cohort, 86.4% were men; mean age was 41.3 ± 9.2 years. Mean AHI was 30.7 ± 25.6, with 34.1% having mild (AHI 5-14.9), 29.2% moderate (AHI 15-29.9), and 36.8% severe (AHI ≥ 30) OSA. Successful therapy was significantly more common with adjustable appliances. Obstructive events were reduced to < 5/h in 56.8% with adjustable compared to 47.0% with fixed appliances (p = 0.02). Similarly, a reduction of events to < 10 with resolution of sleepiness occurred in 66.4% with adjustable appliances versus 44.9% with fixed appliances (p < 0.001). For both devices, success was more common in younger patients, with lower BMI and less severe disease. Conclusions: Adjustable devices produced greater reductions in obstructive events and were more likely to provide successful therapy, especially in moderate-severe OSA. Fixed appliances were effective in mild disease, but were less successful in those with higher AHIs. Given these findings, the baseline AHI should be considered when selecting the type of oral appliance. Citation: Lettieri CJ; Paolino N; Eliasson AH; Shah AA; Holley AB. Comparison of adjustable and fixed oral appliances for the treatment of obstructive sleep apnea. J Clin Sleep Med 2011;7(5):439-445. PMID:22003337

Use of Residential Smart Appliances for Peak-Load Shifting and Spinning Reserves Cost/Benefit Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sastry, Chellury; Pratt, Robert G.; Srivastava, Viraj

2010-12-01

In this report, we present the results of an analytical cost/benefit study of residential smart appliances from a utility/grid perspective in support of a joint stakeholder petition to the ENERGY STAR program within the Environmental Protection Agency (EPA) and Department of Energy (DOE). The goal of the petition is in part to provide appliance manufacturers incentives to hasten the production of smart appliances. The underlying hypothesis is that smart appliances can play a critical role in addressing some of the societal challenges, such as anthropogenic global warming, associated with increased electricity demand, and facilitate increased penetration of renewable sources ofmore » power. The appliances we consider include refrigerator/freezers, clothes washers, clothes dryers, room air-conditioners, and dishwashers. The petition requests the recognition that providing an appliance with smart grid capability, i.e., products that meet the definition of a smart appliance, is at least equivalent to a corresponding five percent in operational machine efficiencies. It is then expected that given sufficient incentives and value propositions, and suitable automation capabilities built into smart appliances, residential consumers will be adopting these smart appliances and will be willing participants in addressing the aforementioned societal challenges by more effectively managing their home electricity consumption. The analytical model we utilize in our cost/benefit analysis consists of a set of user-definable assumptions such as the definition of on-peak (hours of day, days of week, months of year), the expected percentage of normal consumer electricity consumption (also referred to as appliance loads) that can shifted from peak hours to off-peak hours, the average power rating of each appliance, etc. Based on these assumptions, we then formulate what the wholesale grid operating-cost savings, or benefits, would be if the smart capabilities of appliances were invoked, and some percentage of appliance loads were shifted away from peak hours to run during off-peak hours, and appliance loads served power-system balancing needs such as spinning reserves that would otherwise have to be provided by generators. The rationale is that appliance loads can be curtailed for about ten minutes or less in response to a grid contingency without any diminution in the quality of service to the consumer. We then estimate the wholesale grid operating-cost savings based on historical wholesale-market clearing prices (location marginal and spinning reserve) from major wholesale power markets in the United States. The savings derived from the smart grid capabilities of an appliance are then compared to the savings derived from a five percent increase in traditional operational machine efficiencies, referred to as cost in this report, to determine whether the savings in grid operating costs (benefits) are at least as high as or higher than the operational machine efficiency credit (cost).« less

Securing Gender Equality through a Nexus of Energy Policy Performance and Relative Political Performance

NASA Astrophysics Data System (ADS)

Perkins-Ozuagiemhe, Andrea Christen

This dissertation presents what is believed to be the first empirical study that measures the effect of increasing access to modern household energy sources upon advancing gender equality within developing countries. As a powerful and fundamental public infrastructural socio-economic building block, improved access to modern energy in developing countries delivers the necessary economic ingredient of time as a major component of household production and consumption and captures the interdependence between market and household economies. Thus, because it has been empirically proven that men and women differ in their utilization of household energy with women spending more time engaged in non-market household labor than men, improving access to modern household energy in developing countries, especially in rural areas, theoretically would disproportionately affect women's lives. Essentially, the element of "time" not only extends the day for women to use towards more economically and educationally productive activities, but also lessens the burden of domestic chores from women with technological advancements in more time-efficient household appliances and cleaner modern energy sources. This dissertation introduces gender differentiation in a model in the form of a gender relative status composite measure comparing socio-economic achievements in secondary education, life expectancy, and labor force participation rates by varying degree of demographic transition, thereby, measuring the effect of improved access to modern household energy upon overall gender equality. Fixed effects panel regressions employing a Driscoll-Kraay non-parametric covariance matrix, and estimated and interpreted adjusted predictions and marginal effects of the two-way interaction between a country's available access to residential electric power (kWh per capita) and the level of relative political performance against predicted values of gender relative status are employed. The models confirm that, in fact, that women are not impacted equally by energy policy preferences as men and that women in developing countries benefit from increased access to modern household energy. Thus, gender-differentiated energy usage illustrates why treating population as a homogenous group fails to capture how energy policy preferences and energy policy performance can affect different subgroups of population in terms of individual choices and how those differences can affect an overall economic growth and development. Fundamental theoretical implications emerge from this dissertation's empirical findings. First, improving gender equality through technological advancements in household electricity facilitates the progress of demographic transition in terms of reducing fertility rates. Time altering effects of increased access and use of household electricity modify intra-household relations by diminishing differing roles between men and women. When women gain greater autonomy facilitated by increasing time via access to modern household electricity for more economically and educationally productive activities, fertility rates and child births tend to decrease by altering choice in family size with increased investments in children. The effect that the reduction in fertility generated by increased gender equality has upon demographic transition is that it alters the change in age structure in a developing country by decreasing youth dependency ratios generating the demographic dividend. Gender equality-generated fertility reductions may also facilitate the return to human capital by lessening the burden of non-SNA work and activities including reducing child care, increasing female labor force participation rates.

46 CFR 78.47-38 - Valves and closing appliances.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Valves and closing appliances. 78.47-38 Section 78.47-38... Fire and Emergency Equipment, Etc. § 78.47-38 Valves and closing appliances. (a) All valves and closing appliances, or other mechanisms which may be required to be operated for damage control purposes in case of...

7 CFR 3300.13 - Determination of the efficiency of the thermal appliances as installed in the insulated body.

Code of Federal Regulations, 2010 CFR

2010-01-01

... appliances as installed in the insulated body. 3300.13 Section 3300.13 Agriculture Regulations of the... Determination of the efficiency of the thermal appliances as installed in the insulated body. In determining the efficiency of a thermal appliance with respect to maintaining a prescribed temperature inside the body, the...

46 CFR 78.17-5 - Valves and closing appliances.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Valves and closing appliances. 78.17-5 Section 78.17-5..., Drills, and Inspections § 78.17-5 Valves and closing appliances. (a) It shall be the duty of the master to see that all valves, including cross connecting valves where fitted, and other appliances such as...

Mountain Plains Learning Experience Guide: Appliance Repair. Course: Heater-Type Appliances.

ERIC Educational Resources Information Center

Ziller, T.

One of two individualized courses included in an appliance repair curriculum (see CE 027 767), this course covers minor and major heater-type appliances. The course is comprised of six units: (1) Irons, (2) Roasters, (3) Space Heaters, (4) Water Heaters, (5) Electric Ranges, and (6) Gas Ranges. Each unit begins with a Unit Learning Experience…

Crew appliance concepts. Volume 2, appendix B: Shuttle orbiter appliances supporting engineering data. [food management and personal hygiene

NASA Technical Reports Server (NTRS)

Proctor, B. W.; Reysa, R. P.; Russell, D. J.

1975-01-01

Technical data collected for the food management and personal hygiene appliances considered for the shuttle orbiter are presented as well as plotted and tabulated trade study results for each appliance. Food storage, food operation, galley cleanup, waste collection/transfer, body cleansing, and personal grooming were analyzed.

46 CFR 133.40 - Evaluation, testing and approval of lifesaving appliances and arrangements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... OCMI for use on the OSV. (c) The Commandant (CG-521) may accept a novel lifesaving appliance or... Evaluation, Testing and Acceptance of Prototype Novel Life-saving Appliances and Arrangements; or (2) Has... OCMI deems the crew's ability to use and assist others in the use of the lifesaving appliances or...

Electricity end use demand study for Egypt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turiel, I.; Lebot, B.; Nadel, S.

1990-12-01

This report describes the results of a study undertaken by Lawrence Berkeley Laboratory (LBL) to develop an approach for reducing electricity demand in the residential sector in Egypt. A team with expertise in appliance energy usage, appliance manufacturing, appliance testing, and energy analysis was assembled to work on this project. The team visited Egypt during the month of March 1990. They met with the Egyptian Organization for Energy Planning (OEP) and with many other parties. They also visited eleven appliance manufacturing facilities. The project tasks are: data gathering and analysis; assessment of appliance manufacturing plants; demonstration of microcomputer programs; gatheringmore » of data on appliance standards and test procedures; and impact of programs to foster energy efficiency of electricity use.« less

Safety lock-out device for electrical appliances

DOEpatents

Cliff, Jr., Paul L.

1996-01-01

A safety lock-out device prevents the insertion of an electrical power cord into an electrical power cord receptacle of an electrical appliance. The devise comprises a mounting plate fastened to the appliance and a cover plate hingedly attached to the appliance. The cover plate is movable between a first position and a second position such that, in the first position, the cover plate covers and prevents insertion of a power cord into the appliance receptacle. In said second position, the appliance receptacle is uncovered to permit insertion of a power cord into the receptacle. Extending a lock shank through aligned openings formed in flange members extending from the mounting plate and the cover plate locks the cover plate in the first position.

Safety lock-out device for electrical appliances

DOEpatents

Cliff, P.L. Jr.

1996-07-09

A safety lock-out device prevents the insertion of an electrical power cord into an electrical power cord receptacle of an electrical appliance. The device comprises a mounting plate fastened to the appliance and a hinged cover plate attached to the appliance. The cover plate is movable between a first position and a second position such that, in the first position, the cover plate covers and prevents insertion of a power cord into the appliance receptacle. In said second position, the appliance receptacle is uncovered to permit insertion of a power cord into the receptacle. Extending a lock shank through aligned openings formed in flange members extending from the mounting plate, the cover plate locks the cover plate in the first position. 15 figs.

Disaster Loss and Social Media: Can Online Information Increase Flood Resilience?

NASA Astrophysics Data System (ADS)

Allaire, M.

2016-12-01

When confronted with natural disasters, individuals around the world increasingly use online resources to become informed of forecasted conditions and advisable actions. This study tests the effectiveness of online information and social media in enabling households to reduce disaster losses. The 2011 Bangkok flood is utilized as a case study since it was one of the first major disasters to affect a substantial population connected to social media. The role of online information is investigated with a mixed methods approach. Both quantitative (propensity score matching) and qualitative (in-depth interviews) techniques are employed. The study relies on two data sources - survey responses from 469 Bangkok households and in-depth interviews with twenty-three internet users who are a subset of the survey participants. Propensity score matching indicates that social media enabled households to reduce flood losses by an average of 37% (USD 3,708), using a nearest neighbor estimator. This reduction is massive when considering that total flood losses for the full sample averaged USD 4,903. Social media offered information not available from other sources, such as localized and nearly real-time updates of flood location and depth. With this knowledge, households could move belongings to higher ground before floodwaters arrived. These findings suggest that utilizing social media users as sensors could better inform populations during disasters. Overall, the study reveals that online information can enable effective disaster preparedness and reduce losses.

40 CFR 82.306 - Prohibited products.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) PROTECTION OF STRATOSPHERIC OZONE Ban on Refrigeration and Air-Conditioning Appliances Containing HCFCs § 82...-charged appliance component for air-conditioning or refrigeration appliances manufactured on or after...

40 CFR 82.306 - Prohibited products.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) PROTECTION OF STRATOSPHERIC OZONE Ban on Refrigeration and Air-Conditioning Appliances Containing HCFCs § 82...-charged appliance component for air-conditioning or refrigeration appliances manufactured on or after...

40 CFR 82.306 - Prohibited products.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) PROTECTION OF STRATOSPHERIC OZONE Ban on Refrigeration and Air-Conditioning Appliances Containing HCFCs § 82...-charged appliance component for air-conditioning or refrigeration appliances manufactured on or after...

40 CFR 82.306 - Prohibited products.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) PROTECTION OF STRATOSPHERIC OZONE Ban on Refrigeration and Air-Conditioning Appliances Containing HCFCs § 82...-charged appliance component for air-conditioning or refrigeration appliances manufactured on or after...

40 CFR 82.306 - Prohibited products.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) PROTECTION OF STRATOSPHERIC OZONE Ban on Refrigeration and Air-Conditioning Appliances Containing HCFCs § 82...-charged appliance component for air-conditioning or refrigeration appliances manufactured on or after...

Does Validity Fall from the Sky? Observant Farmers and the Endogeneity of Rainfall

NASA Astrophysics Data System (ADS)

Miller, B. M.

2016-12-01

Weather, particularly rainfall, is a popular source of identifying variation in many areas of empirical economics. Deviations from mean rainfall are commonly used as a source of exogenous and unpredictable variation in household consumption, aggregate consumption, and income. Yet the prevalence of 10-day weather forecasts and longer-range seasonal forecasts enabled by earth observations suggest plenty of information about future weather events is available. This paper posits that farmers observe signals about future rainfall outcomes and respond appropriately. While the idea of short-run weather expectations influencing crop choices has been occasionally speculated, this paper's broad-based empirical evidence of such adaptation is new. Evidence of anticipatory adaptation is found in two data sets on Indian agriculture which are popular both in general and among papers using rainfall for identifying variation. The crop selections of Indian farmers are found to be strongly correlated with the season's upcoming rainfall in an agronomically efficient manner. In years where rainfall is one standard deviation below the mean, the district-wide acreage of sorghum (a relatively drought resistant crop) increases by almost 3%, while the district-wide acreage of rice (a relatively water-intensive crops) decreases by over 1%. The response of farming households from a popular survey of rural villages are larger than the average response of aggregate acreage, consistent with poorer, smaller-scale farmers being more risk averse. This paper also presents a methodology for estimating the impact of income shocks which accounts for the anticipatory adaptation enabled by this information.

Cephalometric effects of the Jones Jig appliance followed by fixed appliances in Class II malocclusion treatment

PubMed Central

Patel, Mayara Paim; Henriques, José Fernando Castanha; de Freitas, Karina Maria Salvatore; Grec, Roberto Henrique da Costa

2014-01-01

Objective The aim of this study was to cephalometrically assess the skeletal and dentoalveolar effects of Class II malocclusion treatment performed with the Jones Jig appliance followed by fixed appliances. Methods The sample comprised 25 patients with Class II malocclusion treated with the Jones Jig appliance followed by fixed appliances, at a mean initial age of 12.90 years old. The mean time of the entire orthodontic treatment was 3.89 years. The distalization phase lasted for 0.85 years, after which the fixed appliance was used for 3.04 years. Cephalograms were used at initial (T1), post-distalization (T2) and final phases of treatment (T3). For intragroup comparison of the three phases evaluated, dependent ANOVA and Tukey tests were used. Results Jones Jig appliance did not interfere in the maxillary and mandibular component and did not change maxillomandibular relationship. Jones Jig appliance promoted distalization of first molars with anchorage loss, mesialization and significant extrusion of first and second premolars, as well as a significant increase in anterior face height at the end of treatment. The majority of adverse effects that occur during intraoral distalization are subsequently corrected during corrective mechanics. Buccal inclination and protrusion of mandibular incisors were identified. By the end of treatment, correction of overjet and overbite was observed. Conclusions Jones Jig appliance promoted distalization of first molars with anchorage loss represented by significant mesial movement and extrusion of first and second premolars, in addition to a significant increase in anterior face height. PMID:25162565

Effects of mechanical properties of thermoplastic materials on the initial force of thermoplastic appliances.

PubMed

Kohda, Naohisa; Iijima, Masahiro; Muguruma, Takeshi; Brantley, William A; Ahluwalia, Karamdeep S; Mizoguchi, Itaru

2013-05-01

To measure the forces delivered by thermoplastic appliances made from three materials and investigate effects of mechanical properties, material thickness, and amount of activation on orthodontic forces. Three thermoplastic materials, Duran (Scheu Dental), Erkodur (Erkodent Erich Kopp GmbH), and Hardcast (Scheu Dental), with two different thicknesses were selected. Values of elastic modulus and hardness were obtained from nanoindentation measurements at 28°C. A custom-fabricated system with a force sensor was employed to obtain measurements of in vitro force delivered by the thermoplastic appliances for 0.5-mm and 1.0-mm activation for bodily tooth movement. Experimental results were subjected to several statistical analyses. Hardcast had significantly lower elastic modulus and hardness than Duran and Erkodur, whose properties were not significantly different. Appliances fabricated from thicker material (0.75 mm or 0.8 mm) always produced significantly greater force than those fabricated from thinner material (0.4 mm or 0.5 mm). Appliances with 1.0-mm activation produced significantly lower force than those with 0.5-mm activation, except for 0.4-mm thick Hardcast appliances. A strong correlation was found between mechanical properties of the thermoplastic materials and force produced by the appliances. Orthodontic forces delivered by thermoplastic appliances depend on the material, thickness, and amount of activation. Mechanical properties of the polymers obtained by nanoindentation testing are predictive of force delivery by these appliances.

The UK-DALE dataset, domestic appliance-level electricity demand and whole-house demand from five UK homes

PubMed Central

Kelly, Jack; Knottenbelt, William

2015-01-01

Many countries are rolling out smart electricity meters. These measure a home’s total power demand. However, research into consumer behaviour suggests that consumers are best able to improve their energy efficiency when provided with itemised, appliance-by-appliance consumption information. Energy disaggregation is a computational technique for estimating appliance-by-appliance energy consumption from a whole-house meter signal. To conduct research on disaggregation algorithms, researchers require data describing not just the aggregate demand per building but also the ‘ground truth’ demand of individual appliances. In this context, we present UK-DALE: an open-access dataset from the UK recording Domestic Appliance-Level Electricity at a sample rate of 16 kHz for the whole-house and at 1/6 Hz for individual appliances. This is the first open access UK dataset at this temporal resolution. We recorded from five houses, one of which was recorded for 655 days, the longest duration we are aware of for any energy dataset at this sample rate. We also describe the low-cost, open-source, wireless system we built for collecting our dataset. PMID:25984347

A prospective study on the clinical effectiveness of the stainless steel crown Herbst appliance.

PubMed

Latkauskiene, Dalia; Jakobsone, Gundega; McNamara, James A

2012-09-01

To evaluate the clinical performance of the stainless steel crown Herbst (cHerbst) used as a single appliance for a single phase therapy. A total of 180 consecutive Class II patients were treated with cHerbst for one year and followed up one year after the end of treatment. Class I relationship was achieved in all 175 patients who finished the functional phase of treatment, 58 patients continued treatment with fixed appliances while 21 patients (12%) showed relapse. Seventy two patients (41.1%) obtained and maintained stable Class I relationship one year after treatment with the cHerbst appliance used as a single appliance. Altogether 46 episodes of appliance breakages were observed and most of them could be repaired at the chair side. Patients' questionnaire revealed that in general the appliance was easy to tolerate and did not cause esthetic or functional problems. The crown Herbst appliance is a viable therapeutical option in patients with Class II malocclusions and it is characterized by low complication rate along with good patient compliance. Copyright © 2011 Società Italiana di Ortodonzia SIDO. Published by Elsevier Srl. All rights reserved.

The UK-DALE dataset, domestic appliance-level electricity demand and whole-house demand from five UK homes

NASA Astrophysics Data System (ADS)

Kelly, Jack; Knottenbelt, William

2015-03-01

Many countries are rolling out smart electricity meters. These measure a home’s total power demand. However, research into consumer behaviour suggests that consumers are best able to improve their energy efficiency when provided with itemised, appliance-by-appliance consumption information. Energy disaggregation is a computational technique for estimating appliance-by-appliance energy consumption from a whole-house meter signal. To conduct research on disaggregation algorithms, researchers require data describing not just the aggregate demand per building but also the ‘ground truth’ demand of individual appliances. In this context, we present UK-DALE: an open-access dataset from the UK recording Domestic Appliance-Level Electricity at a sample rate of 16 kHz for the whole-house and at 1/6 Hz for individual appliances. This is the first open access UK dataset at this temporal resolution. We recorded from five houses, one of which was recorded for 655 days, the longest duration we are aware of for any energy dataset at this sample rate. We also describe the low-cost, open-source, wireless system we built for collecting our dataset.

Effect of microbubbled water on the removal of a biofilm attached to orthodontic appliances--an in vitro study.

PubMed

Mukumoto, Mio; Ohshima, Tomoko; Ozaki, Miwa; Konishi, Hirokazu; Maeda, Nobuko; Nakamura, Yoshiki

2012-01-01

Orthodontic appliances often cause oral diseases such as dental caries and gingivitis due to the attachment of an oral biofilm. However, there are few reliable methods to remove the biofilm from the orthodontic appliances. The aim of this study was to investigate the effects of microbubbled water on the removal of biofilms made with Streptococcus mutans or Candida albicans on orthodontic appliances. The orthodontic appliances with biofilm were immersed with microbubbled water and the remaining biofilm on the appliances was detected and measured using a micro-plate reader and an absorbance meter. The microbubbled water had a sufficient effect on the removal of biofilm from orthodontic appliances. The effects of microbubbled water were significantly higher than those of tap water (S. mutans: p<0.05, C. albicans: p<0.01). The results of this study suggest that microbubbled water is effective in the removal of biofilm from the mouth of orthodontic patients.

Association of tooth brushing behavior with oral hygiene index among students using fixed appliance

NASA Astrophysics Data System (ADS)

Ria, N.; Eyanoer, P.

2018-03-01

Uses of fixed appliance have become popular recently. The purpose of its use is to correct malposition of teeth in order to normalize the masticatory function and to eliminate the accumulation of food remain between the teeth. These will prevent the formation of caries and any periodontal tissue disease. Fixed appliance patients must routinely maintain their oral hygiene. This study was an analytical survey with cross-sectional design to know the relationship between behavior in tooth brushing of students using thefixed appliance and oral hygiene in Poltekkes Kemenkes Medan. The average of Oral Hygiene Index – Simplified (OHI-S) value of students using fixed appliance (2.68) was still above national target which is ≤2, and there was a relationship between behavior in tooth brushing of students using the fixed appliance and oral hygiene (p<0.02). In conclusion, to get good oral hygiene and to prevent caries formation and periodontal disease patients using fixed appliances should maintain their dental health.

Foresee: A user-centric home energy management system for energy efficiency and demand response

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jin, Xin; Baker, Kyri A.; Christensen, Dane T.

This paper presents foresee, a user-centric home energy management system that can help optimize how a home operates to concurrently meet users' needs, achieve energy efficiency and commensurate utility cost savings, and reliably deliver grid services based on utility signals. Foresee is built on a multiobjective model predictive control framework, wherein the objectives consist of energy cost, thermal comfort, user convenience, and carbon emission. Foresee learns user preferences on different objectives and acts on their behalf to operate building equipment, such as home appliances, photovoltaic systems, and battery storage. In this work, machine-learning algorithms were used to derive data-driven appliancemore » models and usage patterns to predict the home's future energy consumption. This approach enables highly accurate predictions of comfort needs, energy costs, environmental impacts, and grid service availability. Simulation studies were performed on field data from a residential building stock data set collected in the Pacific Northwest. Results indicated that foresee generated up to 7.6% whole-home energy savings without requiring substantial behavioral changes. When responding to demand response events, foresee was able to provide load forecasts upon receipt of event notifications and delivered the committed demand response services with 10% or fewer errors. Foresee fully utilized the potential of the battery storage and controllable building loads and delivered up to 7.0-kW load reduction and 13.5-kW load increase. As a result, these benefits are provided while maintaining the occupants' thermal comfort or convenience in using their appliances.« less

Foresee: A user-centric home energy management system for energy efficiency and demand response

DOE PAGES

Jin, Xin; Baker, Kyri A.; Christensen, Dane T.; ...

2017-08-23

This paper presents foresee, a user-centric home energy management system that can help optimize how a home operates to concurrently meet users' needs, achieve energy efficiency and commensurate utility cost savings, and reliably deliver grid services based on utility signals. Foresee is built on a multiobjective model predictive control framework, wherein the objectives consist of energy cost, thermal comfort, user convenience, and carbon emission. Foresee learns user preferences on different objectives and acts on their behalf to operate building equipment, such as home appliances, photovoltaic systems, and battery storage. In this work, machine-learning algorithms were used to derive data-driven appliancemore » models and usage patterns to predict the home's future energy consumption. This approach enables highly accurate predictions of comfort needs, energy costs, environmental impacts, and grid service availability. Simulation studies were performed on field data from a residential building stock data set collected in the Pacific Northwest. Results indicated that foresee generated up to 7.6% whole-home energy savings without requiring substantial behavioral changes. When responding to demand response events, foresee was able to provide load forecasts upon receipt of event notifications and delivered the committed demand response services with 10% or fewer errors. Foresee fully utilized the potential of the battery storage and controllable building loads and delivered up to 7.0-kW load reduction and 13.5-kW load increase. As a result, these benefits are provided while maintaining the occupants' thermal comfort or convenience in using their appliances.« less

16 CFR § 1406.2 - Background.

Code of Federal Regulations, 2013 CFR

2013-01-01

... BURNING APPLIANCES-NOTIFICATION OF PERFORMANCE AND TECHNICAL DATA § 1406.2 Background. (a) Fire data... burning appliances. Many of these cases involve improper installation of the appliances, especially where...

Human-like robots as platforms for electroactive polymers (EAP)

NASA Astrophysics Data System (ADS)

Bar-Cohen, Yoseph

2008-03-01

Human-like robots, which have been a science fiction for many years, are increasingly becoming an engineering reality thanks to many technology advances in recent years. Humans have always sought to imitate the human appearance, functions and intelligence and as the capability progresses they may become our household appliance or even companion. Biomimetic technologies are increasingly becoming common tools to support the development of such robots. As artificial muscles, electroactive polymers (EAP) are offering important actuation capability for making such machines lifelike. The current limitations of EAP are hampering the possibilities that can be adapted in such robots but progress is continually being made. As opposed to other human made machines and devices, this technology raises various questions and concerns that need to be addressed. These include the need to prevent accidents, deliberate harm, or their use in crimes. In this paper the state-of-the-art and the challenges will be reviewed.

Renewable energy load assessment for Boquillas Del Carmen Coahuila, Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foster, R.

1995-08-01

This report outlines the estimates that were made in 1992 of the potential load requirements for Boquillas del Carmen, a small Mexican village on the northern border of the state of Coahuila, Mexico near Big Bend National Park in southern Texas. The study was made to help determine the possibility that village might be electrified by solar or wind energy. Various estimates of are given of the potential load based on estimates ranging from basic use of lights, radio, television, and small household appliances to microwave ovens, refrigerators, and direct evaporative coolers. The low-energy consumption case was estimated to bemore » at 23.0 kWh/month per residence per month, and the high-energy consumption case (with cooling) was 140.7 kWh/month per residence. On average, the typical residence is occupied by five individuals.« less

National energy conservation

NASA Technical Reports Server (NTRS)

1975-01-01

A set of energy conservation actions that cut across all sectors of the economy were analyzed so that all actions under consideration be analyzed systematically and as a whole. The actions considered were as follows: (1) roll back the price of newly discovered oil, (2) freeze gasoline production for 3 years at 1972 levels, (3) mandate automobile mileage improvements, (4) require industry to improve energy efficiency, (5) require manufacture of household appliances with greater efficiency, (6) force conversion of many power plants from gas and oil to coal. The results showed that considerable gas and oil would be saved by forcing switches to coal. However, the large scale switch to coal was shown to require greatly increased outputs from many other industries that in turn require more energy. It was estimated that nearly 2.5 quads of additional coal were needed to produce these additional requirements. Also, the indirect requirements would create more jobs.

Value analysis of neodymium content in shredder feed: toward enabling the feasibility of rare earth magnet recycling.

PubMed

Bandara, H M Dhammika; Darcy, Julia W; Apelian, Diran; Emmert, Marion H

2014-06-17

In order to facilitate the development of recycling technologies for rare earth magnets from postconsumer products, we present herein an analysis of the neodymium (Nd) content in shredder scrap. This waste stream has been chosen on the basis of current business practices for the recycling of steel, aluminum, and copper from cars and household appliances, which contain significant amounts of rare earth magnets. Using approximations based on literature data, we have calculated the average Nd content in the ferrous shredder product stream to be between 0.13 and 0.29 kg per ton of ferrous scrap. A value analysis considering rare earth metal prices between 2002 and 2013 provides values between $1.32 and $145 per ton of ferrous scrap for this material, if recoverable as pure Nd metal. Furthermore, we present an analysis of the content and value of other rare earths (Pr, Dy, Tb).

Public perceptions of energy consumption and savings

PubMed Central

Attari, Shahzeen Z.; DeKay, Michael L.; Davidson, Cliff I.; Bruine de Bruin, Wändi

2010-01-01

In a national online survey, 505 participants reported their perceptions of energy consumption and savings for a variety of household, transportation, and recycling activities. When asked for the most effective strategy they could implement to conserve energy, most participants mentioned curtailment (e.g., turning off lights, driving less) rather than efficiency improvements (e.g., installing more efficient light bulbs and appliances), in contrast to experts’ recommendations. For a sample of 15 activities, participants underestimated energy use and savings by a factor of 2.8 on average, with small overestimates for low-energy activities and large underestimates for high-energy activities. Additional estimation and ranking tasks also yielded relatively flat functions for perceived energy use and savings. Across several tasks, participants with higher numeracy scores and stronger proenvironmental attitudes had more accurate perceptions. The serious deficiencies highlighted by these results suggest that well-designed efforts to improve the public's understanding of energy use and savings could pay large dividends. PMID:20713724

Electroactive polymer (EAP) actuators for future humanlike robots

NASA Astrophysics Data System (ADS)

Bar-Cohen, Yoseph

2009-03-01

Human-like robots are increasingly becoming an engineering reality thanks to recent technology advances. These robots, which are inspired greatly by science fiction, were originated from the desire to reproduce the human appearance, functions and intelligence and they may become our household appliance or even companion. The development of such robots is greatly supported by emerging biologically inspired technologies. Potentially, electroactive polymer (EAP) materials are offering actuation capabilities that allow emulating the action of our natural muscles for making such machines perform lifelike. There are many technical issues related to making such robots including the need for EAP materials that can operate as effective actuators. Beside the technology challenges these robots also raise concerns that need to be addressed prior to forming super capable robots. These include the need to prevent accidents, deliberate harm, or their use in crimes. In this paper, the potential EAP actuators and the challenges that these robots may pose will be reviewed.

Electroactive Polymer (EAP) Actuators for Future Humanlike Robots

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph

2009-01-01

Human-like robots are increasingly becoming an engineering reality thanks to recent technology advances. These robots, which are inspired greatly by science fiction, were originated from the desire to reproduce the human appearance, functions and intelligence and they may become our household appliance or even companion. The development of such robots is greatly supported by emerging biologically inspired technologies. Potentially, electroactive polymer (EAP) materials are offering actuation capabilities that allow emulating the action of our natural muscles for making such machines perform lifelike. There are many technical issues related to making such robots including the need for EAP materials that can operate as effective actuators. Beside the technology challenges these robots also raise concerns that need to be addressed prior to forming super capable robots. These include the need to prevent accidents, deliberate harm, or their use in crimes. In this paper, the potential EAP actuators and the challenges that these robots may pose will be reviewed.

A Proposal for the Education based on the Information Technology in Technical High Schools, Linking Together Web Programming and Microcontroller

NASA Astrophysics Data System (ADS)

Shinozaki, Kenichi; Yanaru, Torao

Recently, IT (Information Technology) have rapidly revolved and penetrated into the usual human life, with such as the household appliances and the mobile devices. Considering this strong change of social environment, what technology is introduced to satisfy the present educational needs and how to develop the teaching system is very important. Then in this paper, we describe the developed web-teaching material that links Xport, an embedded device server, with the control system using microcontroller technology. In the classes, we have implemented the lessons that utilize this system in the following subjects : programming technology, hardware technology, electronic circuit and practical training. Furthermore, because of high availability of the developed system through internet, it is also useful for the education on science and technical arts in general high schools or in junior high schools as well as in technical high schools.

The status and development of treatment techniques of typical waste electrical and electronic equipment in China: a review.

PubMed

He, Yunxia; Xu, Zhenming

2014-04-01

A large quantity of waste electrical and electronic equipment (WEEE) is being generated because technical innovation promotes the unceasing renewal of products. China's household appliances and electronic products have entered the peak of obsolescence. Due to lack of technology and equipment, recycling of WEEE is causing serious environment pollution. In order to achieve the harmless disposal and resource utilization of WEEE, researchers have performed large quantities of work, and some demonstration projects have been built recently. In this paper, the treatment techniques of typical WEEE components, including printed circuit boards, refrigerator cabinets, toner cartridges, cathode ray tubes, liquid crystal display panels, batteries (Ni-Cd and Li-ion), hard disk drives, and wires are reviewed. An integrated recycling system with environmentally friendly and highly efficient techniques for processing WEEE is proposed. The orientation of further development for WEEE recycling is also proposed.

The effect of biologically and chemically synthesized silver nanoparticles (AgNPs) on biofilm formation

NASA Astrophysics Data System (ADS)

Chojniak, Joanna; Biedroń, Izabela; Mendrek, Barbara; Płaza, Grażyna

2017-11-01

Bionanotechnology has emerged up as integration between biotechnology and nanotechnology for developing biosynthetic and environmental-friendly technology for synthesis of nanomaterials. Different types of nanomaterials like copper, zinc, titanium, magnesium, gold, and silver have applied in the various industries but silver nanoparticles have proved to be most effective against bacteria, viruses and eukaryotic microorganisms. The antimicrobial property of silver nanoparticles are widely known. Due to strong antibacterial property silver nanoparticles are used, e.g. in clothing, food industry, sunscreens, cosmetics and many household and environmental appliances. The aim of the study was to compare the effect of silver nanoparticles (AgNPs) synthesized biologically and chemically on the biofilm formation. The biofilm was formed by the bacteria isolated from the water supply network. The commonly used crystal violet assay (CV) was applied for biofilm analysis. In this study effect of biologically synthesized Ag-NPs on the biofilm formation was evaluated.

Intelligent Home Control System Based on Single Chip Microcomputer

NASA Astrophysics Data System (ADS)

Yang, Libo

2017-12-01

Intelligent home as a way to achieve the realization of the family information has become an important part of the development of social information, Internet of Things because of its huge application prospects, will be smart home industry in the development process of a more realistic breakthrough in the smart home industry development has great significance. This article is based on easy to implement, easy to operate, close to the use of the design concept, the use of STC89C52 microcontroller as the control core for the control terminal, and including infrared remote control, buttons, Web interface, including multiple control sources to control household appliances. The second chapter of this paper describes the design of the hardware and software part of the specific implementation, the fifth chapter is based on the design of a good function to build a specific example of the environment.

Wood Stove Pollution in the Developed World: A Case to Raise Awareness Among Pediatricians.

PubMed

Rokoff, Lisa B; Koutrakis, Petros; Garshick, Eric; Karagas, Margaret R; Oken, Emily; Gold, Diane R; Fleisch, Abby F

2017-06-01

Use of wood for residential heating is regaining popularity in developed countries. Currently, over 11 million US homes are heated with a wood stove. Although wood stoves reduce heating costs, wood smoke may adversely impact child health through the emission of gaseous and particulate air pollutants. Our purpose is to raise awareness of this environmental health issue among pediatricians. To summarize the state of the science, we performed a narrative review of articles published in PubMed and Web of Science. We identified 36 studies in developed countries that reported associations of household wood stove use and/or community wood smoke exposure with pediatric health outcomes. Studies primarily investigated respiratory outcomes, with no evaluation of cardiometabolic or neurocognitive health. Studies found community wood smoke exposure to be consistently associated with adverse pediatric respiratory health. Household wood stove use was less consistently associated with respiratory outcomes. However, studies of household wood stoves always relied on participant self-report of wood stove use, while studies of community wood smoke generally assessed air pollution exposure directly and more precisely in larger study populations. In most studies, important potential confounders, such as markers of socioeconomic status, were unaccounted for and may have biased results. We conclude that studies with improved exposure assessment, that measure and account for confounding, and that consider non-respiratory outcomes are needed. While awaiting additional data, pediatricians can refer patients to precautionary measures recommended by the US Environmental Protection Agency (EPA) to mitigate exposure. These include replacing old appliances with EPA-certified stoves, properly maintaining the stove, and using only dry, well-seasoned wood. In addition, several studies have shown mechanical air filters to effectively reduce wood stove pollution exposure in affected homes and communities. Copyright © 2017 Mosby, Inc. All rights reserved.

Wood Stove Pollution in the Developed World: A Case to Raise Awareness Among Pediatricians

PubMed Central

Rokoff, Lisa B.; Koutrakis, Petros; Garshick, Eric; Karagas, Margaret R.; Oken, Emily; Gold, Diane R.; Fleisch, Abby F.

2017-01-01

Use of wood for residential heating is regaining popularity in developed countries. Currently, over 11 million US homes are heated with a wood stove. Although wood stoves reduce heating costs, wood smoke may adversely impact child health through the emission of gaseous and particulate air pollutants. Our purpose is to raise awareness of this environmental health issue among pediatricians. To summarize the state of the science, we performed a narrative review of articles published in PubMed and Web of Science. We identified 36 studies in developed countries that reported associations of household wood stove use and/or community wood smoke exposure with pediatric health outcomes. Studies primarily investigated respiratory outcomes, with no evaluation of cardiometabolic or neurocognitive health. Studies found community wood smoke exposure to be consistently associated with adverse pediatric respiratory health. Household wood stove use was less consistently associated with respiratory outcomes. However, studies of household wood stoves always relied on participant self-report of wood stove use, while studies of community wood smoke generally assessed air pollution exposure directly and more precisely in larger study populations. In most studies, important potential confounders, such as markers of socioeconomic status, were unaccounted for and may have biased results. We conclude that studies with improved exposure assessment, that measure and account for confounding, and that consider non-respiratory outcomes are needed. While awaiting additional data, pediatricians can refer patients to precautionary measures recommended by the US Environmental Protection Agency (EPA) to mitigate exposure. These include replacing old appliances with EPA-certified stoves, properly maintaining the stove, and using only dry, well-seasoned wood. In addition, several studies have shown mechanical air filters to effectively reduce wood stove pollution exposure in affected homes and communities. PMID:28583817

Effects of the pendulum appliance, cervical headgear, and 2 premolar extractions followed by fixed appliances in patients with Class II malocclusion.

PubMed

de Almeida-Pedrin, Renata Rodrigues; Henriques, José Fernando Castanha; de Almeida, Renato Rodrigues; de Almeida, Marcio Rodrigues; McNamara, James A

2009-12-01

In this retrospective study, we compared the cephalometric effects, the dental-arch changes, and the efficiency of Class II treatment with the pendulum appliance, cervical headgear, or extraction of 2 maxillary premolars, all associated with fixed appliance therapy. The sample of 82 patients with Class II malocclusion was divided into 3 groups: group 1 patients (n = 22; treatment time, 3.8 years) were treated with the pendulum appliance and fixed orthodontic appliances. Group 2 patients (n = 30; treatment time, 3.2 years) were treated with cervical headgear followed by fixed appliances; group 3 patients (n = 30; treatment time, 2.1 years) were treated with 2 maxillary premolar extractions and fixed appliances. The average starting ages of the groups ranged from 13.2 to 13.8 years. Data were obtained from serial cephalometric measurements and dental casts. The dental casts were analyzed with the treatment priority index. The treatment efficiency index was also used. The 3 treatment protocols produced similar cephalometric effects, especially skeletally. Comparisons among the 2 distalizing appliances (pendulum and cervical headgear) and extraction of 2 maxillary premolars for Class II treatment showed changes primarily in the maxillary dentoalveolar component and dental relationships. The facial profile was similar after treatment, except for slightly more retrusion of the upper lip in the extraction patients. The treatment priority index demonstrated that occlusal outcomes also were similar among the groups. The treatment efficiency index had higher values for the extraction group. The effects of treatment with the pendulum appliance or cervical headgear and extraction of 2 maxillary premolars associated with fixed appliances were similar from both occlusal and cephalometric standpoints. Class II treatment with extraction of maxillary teeth was more efficient because of the shorter treatment time. Differences in maxillary incisor retraction should be noted, but these differences might have been due to greater maxillary dentoalveolar protrusion in the extraction group before treatment.

Routines for interocclusal appliance therapy among general dental practitioners in a Swedish county.

PubMed

Gnauck, Maja; Helkimo, Martti; Magnusson, Tomas

2012-01-01

The aims of this study were to investigate what kind of interocclusal appliances that were chosen among Swedish dentists when treating temporomandibular disorders (TMD), the clinical rationale for the treatment, the diagnoses that warranted the appliance treatment, the use of adjunct TMD treatments and prognostic considerations, and possible differences in these respects between children/adolescents and adults with TMD, and, finally, possible differences between private practitioners and general practitioners in the public dental service. During the 12-months-period April 2009-March 2010 all general dental practitioners in the county of Jönköping, Sweden, were asked to fill in a questionnaire when performing a TMD treatment with an interocclusal appliance. A total of 394 questionnaires were filled in and returned, 216 (55%) from dentists in public dental service and 178 (45%) from private practitioners. It was found that in 40% of the cases, no pre-treatment recording of the functional status in the masticatory system had been made. The commonest reasons for the treatment were bruxism, headache, and replacement of a previous appliance. Less than half of the appliances made were hard acrylic appliances. Some kind of adjunct therapy had been made in 22% of the cases treated in public dental service. The corresponding figure for those treated by private practitioners was 25%. Therapeutic jaw exercises was the commonest adjunct therapy followed by selective occlusal adjustment. In the vast majority of cases, the dentists judged the prognosis of the treatment to be good. It is concluded that a large number of appliances made to treat TMD were soft appliances, especially in public dental service. This reflects a possible overuse of soft appliances at the expense of hard acrylic appliances. Furthermore, in a large number of cases, the treatment was performed without any pre-treatment registrations, and adjunct therapies were rarely used. In all these respects,there is an improvement potential for the treatment of TMD in general dental practice.

The Demand Reduction Potential of Smart Appliances in U.S. Homes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Makhmalbaf, Atefe; Srivastava, Viraj; Parker, Graham B.

The widespread deployment of demand respond (DR) enabled home appliances is expected to have significant reduction in the demand of electricity during peak hours. The work documented in this paper focuses on estimating the energy shift resulting from the installation of DR enabled smart appliances in the U.S. This estimation is based on analyzing the market for smart appliances and calculating the total energy demand that can potentially be shifted by DR control in appliances. Appliance operation is examined by considering their sub components individually to identify their energy consumptions and savings resulting from interrupting and shifting their load, e.g.,more » by delaying the refrigerator defrost cycle. In addition to major residential appliances, residential pool pumps are also included in this study given their energy consumption profiles that make them favorable for DR applications. In the market analysis study documented in this paper, the U.S. Energy Information Administration's (EIA) Residential Energy Consumption Survey (RECS) and National Association of Home Builders (NAHB) databases are used to examine the expected life of an appliance, the number of appliances installed in homes constructed in 10 year intervals after 1940 and home owner income. Conclusions about the effectiveness of the smart appliances in reducing electrical demand have been drawn and a ranking of appliances in terms of their contribution to load shift is presented. E.g., it was concluded that DR enabled water heaters result in the maximum load shift; whereas, dishwashers have the highest user elasticity and hence the highest potential for load shifting through DR. This work is part of a larger effort to bring novel home energy management concepts and technologies to reduce energy consumption, reduce peak electricity demand, integrate renewables and storage technology, and change homeowner behavior to manage and consume less energy and potentially save consumer energy costs.« less

24 CFR 3280.709 - Installation of appliances.

Code of Federal Regulations, 2012 CFR

2012-04-01

... does not apply if both appliances are direct vent system (sealed combustion system) appliances. (2) If... stove shall not be installed in a sleeping room. (v) Hearth extension shall be of noncombustible...

Short-term changes in chewing efficiency and subjective evaluation in normal dentate subjects after insertion of oral appliances with an occlusal flat table.

PubMed

Satokawa, Y; Minami, I; Wakabayashi, N

2018-02-01

Oral appliances with an occlusal flat table are used as treatment dentures. However, the short-term effect of insertion of such oral appliances on chewing has not been reported. This study aimed to determine whether experimental and continuous insertion of oral appliances with an occlusal flat table has an effect on chewing efficiency and Oral Health Impact Profile (OHIP) in healthy participants. Ten participants each in the oral-appliance and control (no oral-appliance insertion) groups attended six data collection sessions for 5 consecutive days. Participants answered the OHIP questionnaire and underwent the chewing efficiency test. For each parameter, intergroup differences were investigated in terms of change from baseline to immediately after oral-appliance insertion (0 hour; P < .05) and from 0 hour to 24, 48, 72 and 96 hours after oral-appliance insertion (P < .05). There were significant differences between groups in the degree of change in chewing efficiency and OHIP scores for functional limitation, physical pain, physical disability and handicap from baseline to 0 hour (all, P < .001); among these, only OHIP scores for functional limitation and physical pain demonstrated significant differences in degree of change between the two groups at 96 hours after appliance insertion (P = .477 and .275, respectively). Differences between the two groups in the degree of change in other parameters were not significant. Insertion of oral appliances caused a decrease in chewing efficiency and an increase in OHIP scores. Continuous insertion improved functional limitation and physical pain within 96 hours. © 2017 John Wiley & Sons Ltd.

Emission factors from small scale appliances burning wood and pellets

NASA Astrophysics Data System (ADS)

Ozgen, Senem; Caserini, Stefano; Galante, Silvia; Giugliano, Michele; Angelino, Elisabetta; Marongiu, Alessandro; Hugony, Francesca; Migliavacca, Gabriele; Morreale, Carmen

2014-09-01

Four manually fed (6-11 kW) firewood burning and two automatic wood pellets (8.8-25 kW) residential heating appliances were tested under real-world operating conditions in order to determine emission factors (EFs) of macropollutants, i.e., carbon monoxide (CO), nitrogen oxides (NOx), non-methane hydrocarbons (NMHC), particulate matter (PM) and trace pollutants such as polycyclic aromatic hydrocarbons (PAH) and dioxins. The results were examined for the influence of different factors (i.e., type of wood, appliance and combustion cycle). The experimental EFs were also compared with the values proposed by the European emission inventory guidebook used in the local inventory in order to evaluate their representativeness of real world emissions. The composite macropollutant EFs for manually fed appliances were: for CO 5858 g GJ-1, for NOx 122 g GJ-1, NMHC 542 g GJ-1, PM 254 g GJ-1, whereas emissions were much lower for automatic pellets appliances: CO 219 g GJ-1, for NOx 66 g GJ-1, NMHC 5 g GJ-1, PM 85 g GJ-1. The highest emissions were generally observed for the open fireplace, however traditional and advanced stoves have the highest overall CO EFs. Especially for the advanced stove real-world emissions are far worse than those measured under cycles used for type testing of residential solid fuel appliances. No great difference is observed for different firewood types in batch working appliances, diversely the quality of the pellets is observed to influence directly the emission performance of the automatic appliances. Benzo(b)fluoranthene is the PAH with the highest contribution (110 mg GJ-1 for manual appliances and 2 mg GJ-1 for automatic devices) followed by benzo(a)pyrene (77 mg GJ-1 for manual appliances and 0.8 mg GJ-1 for automatic devices).

Office management of obstructive sleep apnoea: appliances.

PubMed

Johnson, Matthew D

2015-08-01

Oral appliances are becoming increasingly common in the treatment of obstructive sleep apnoea (OSA). They work by advancing the mandible and opening the pharynx. There are several types of devices available for use. Many patients intolerant to continuous positive airway pressure (CPAP) are using oral appliances for OSA. Oral appliances have been shown to improve polysomnography, quality of life and health measures associated with OSA. There is current work to better identify patients who are ideal candidates. Development of titratable devices and monitoring are optimizing usage. They have been compared with CPAP, with both showing improvement in OSA; however, CPAP remains superior overall. Oral appliances are becoming first-line therapy for mild and moderate OSA. They provide a meaningful alternative in severe OSA for patients unable to use CPAP. Device titration and usage monitoring are beginning to hone oral appliances as a therapeutic option.

Early correction of unilateral scissor bite using transforce appliance and modified twin block appliance

PubMed Central

Chandorikar, Harshal; Nagrik, Arun; Bhad, Wasundhara A; Chavan, Santosh J; Doshi, Umal H

2017-01-01

Early treatment of scissor bite has been advocated mainly to prevent function jaw shift that can eventually lead to permanent skeletal asymmetry and temporomandibular joint pathosis. Although unilateral scissor bite is more common, most of the times, bilateral mandibular expansion is indicated. Lingual transforce appliance can be useful in such cases. This article presents a patient with unilateral scissor bite in mixed dentition with alveolar narrowing. Transforce appliance was used for scissor bite correction followed by modified twin block appliance for stabilization and settling of occlusion till the eruption of premolars. The case was finished with fixed mechanotherapy. Two years after completion of treatment, results were well maintained. Our results suggest that lingual transforce appliance along with careful management of occlusion is effective in the early management of severe unilateral scissor bite. PMID:28546961

Treatment effects of skeletally anchored Forsus FRD EZ and Herbst appliances: A retrospective clinical study.

PubMed

Celikoglu, Mevlut; Buyuk, Suleyman Kutalmis; Ekizer, Abdullah; Unal, Tuba

2016-03-01

To evaluate the skeletal, dentoalveolar, and soft tissue effects of the Forsus FRD appliance with miniplate anchorage inserted in the mandibular symphyses and to compare the findings with a well-matched control group treated with a Herbst appliance for the correction of a skeletal Class II malocclusion due to mandibular retrusion. The sample consisted of 32 Class II subjects divided into two groups. Group I consisted of 16 patients (10 females and 6 males; mean age, 13.20 ± 1.33 years) treated using the Forsus FRD EZ appliance with miniplate anchorage inserted in the mandibular symphyses. Group II consisted of 16 patients (9 females and 7 males; mean age, 13.56 ± 1.27 years) treated using the Herbst appliance. Seventeen linear and 10 angular measurements were performed to evaluate and compare the skeletal, dentoalveolar, and soft tissue effects of the appliances using paired and Student's t-tests. Both appliances were effective in correcting skeletal class II malocclusion and showed similar skeletal and soft tissue changes. The maxillary incisor was statistically significantly more retruded in the skeletally anchored Forsus FRD group (P < .01). The mandibular incisor was retruded in the skeletally anchored Forsus FRD group (-4.09° ± 5.12°), while it was protruded in the Herbst group (7.50° ± 3.98°) (P < .001). Although both appliances were successful in correcting the skeletal Class II malocclusion, the skeletally anchored Forsus FRD EZ appliance did so without protruding the mandibular incisors.

Impact of metal and ceramic fixed orthodontic appliances on judgments of beauty and other face-related attributes.

PubMed

Fonseca, Lílian Martins; Araújo, Telma Martins de; Santos, Aline Rôde; Faber, Jorge

2014-02-01

Physical attributes, behavior, and personal ornaments exert a direct influence on how a person's beauty and personality are judged. The aim of this study was to investigate how people who wear a fixed orthodontic appliance see themselves and are seen by others in social settings. A total of 60 adults evaluated their own smiling faces in 3 different scenarios: without a fixed orthodontic appliance, wearing a metal fixed orthodontic appliance, and wearing an esthetic fixed orthodontic appliance. Furthermore, 15 adult raters randomly assessed the same faces in standardized front-view facial photographs. Both the subjects and the raters answered a questionnaire in which they evaluated criteria on a numbered scale ranging from 0 to 10. The models judged their own beauty, and the raters assigned scores to beauty, age, intelligence, ridiculousness, extroversion, and success. The self-evaluations showed decreased beauty scores (P <0.0001) when a fixed orthodontic appliance, especially a metal one, was being worn. There was no statistically significant difference between the 3 situations in the 6 criteria analyzed. A fixed orthodontic appliance did not affect how personal attributes are assessed. However, fixed orthodontic appliances apparently changed the subjects' self-perceptions when they looked in the mirror. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Effect of dental wear, stabilization appliance and anterior tooth reconstruction on mandibular movements during speech.

PubMed

Serrano, Priscila de Oliveira; Faot, Fernanda; Del Bel Cury, Altair Antoninha; Rodrigues Garcia, Renata Cunha Matheus

2008-01-01

This study described changes in mandibular movements during pronunciation of /m/ and /s/ sounds in Portuguese, in patients presenting dental wear before and after appliance insertion and tooth reconstruction. Subjects were divided into a control group of dentate patients and an experimental group of patients with incisal tooth wear due to bruxism. A magnetic jaw tracking device measured the jaw opening, and translations to left and right sides of the mandible during pronunciation of phonemes. Evaluations were carried out 1 week and immediately before appliance insertion; 24 h, 7, 30 and 60 days after appliance insertion; and 1 week and 1 month after tooth reconstruction. Data were submitted to two-way ANOVA, Mann-Whitney and Friedman tests (p<0.05). Jaw opening was different (p<0.05) for both sounds in all periods. The anteroposterior amplitude for /s/ showed differences immediately before and 1 month after appliance insertion (p<0.05). Lateral amplitude for the right side showed differences between groups after appliance insertion for /s/, and 1 and 2 months after appliance insertion for the /m/ (p<0.05). Volunteers with anterior tooth wear had a wider opening movement, and the movements during speech of /m/ and /s/ sounds were not changed after appliance insertion and reconstruction of teeth.

Fabrication of lingual orthodontic appliances: past, present and future.

PubMed

Hutchinson, Ian; Lee, Jang Yeol

2013-09-01

Lingual orthodontics is increasing in popularity, with more adults receiving orthodontic treatment and opting for truly invisible appliances that do not have any limitations on the type of tooth movement they can achieve. In addition, there are a growing number of children receiving lingual appliances as they have been shown to significantly reduce the incidence of decalcification. Combining this growth in popularity with advances in computer technology, it is possible to treatment plan, design the appliance and have it custom made all with the click of a button. This article highlights the different methods that have been utilized in the fabrication of lingual appliances.

Crew appliance computer program manual, volume 1

NASA Technical Reports Server (NTRS)

Russell, D. J.

1975-01-01

Trade studies of numerous appliance concepts for advanced spacecraft galley, personal hygiene, housekeeping, and other areas were made to determine which best satisfy the space shuttle orbiter and modular space station mission requirements. Analytical models of selected appliance concepts not currently included in the G-189A Generalized Environmental/Thermal Control and Life Support Systems (ETCLSS) Computer Program subroutine library were developed. The new appliance subroutines are given along with complete analytical model descriptions, solution methods, user's input instructions, and validation run results. The appliance components modeled were integrated with G-189A ETCLSS models for shuttle orbiter and modular space station, and results from computer runs of these systems are presented.

Distalization of Maxillary First Permanent Molar by Pendulum Appliance in Mixed Dentition Period.

PubMed

Paranna, Sujatha; Shetty, Prakashchandra; Anandakrishna, Latha; Rawat, Anuradha

2017-01-01

Mesial drifting of molar teeth in maxillary arch is corrected by movement of the molars distally. In addition to traditional distal movement techniques, such as extraoral force application and removable appliances, various intra-arch devices have been introduced since 1980s. These intra-arch appliances have nearly eliminated the need for patient cooperation. The purpose of this paper is to report a case of 10-year-old male patient with loss of space in maxillary molar teeth treated by intra-arch appliance-pendulum appliance by distalization of maxillary first permanent molar teeth. Distaliza-tion of the permanent molar teeth helped in proper eruption of second premolar teeth without any extensive treatment procedures. In the present case report, the treatment of developing malocclusion was corrected by utilizing the concept of interceptive orthodontics. Hence, correction of space loss in mixed dentition period using pendulum appliance can eliminate the fixed orthodontic therapy. Paranna S, Shetty P, Anandakrishna L, Rawat A. Distalization of Maxillary First Permanent Molar by Pendulum Appliance in Mixed Dentition Period. Int J Clin Pediatr Dent 2017;10(3):299-301.

[Individual indirect bonding technique (IIBT) using set-up model].

PubMed

Kyung, H M

1989-01-01

There has been much progress in Edgewise Appliance since E.H. Angle. One of the most important procedures in edgewise appliance is correct bracket position. Not only conventional edgewise appliance but also straight wire appliance & lingual appliance cannot be used more effectively unless the bracket position is accurate. Improper bracket positioning may reveal much problems during treatment, especially in finishing state. It may require either rebonding after the removal of the malpositioned bracket or the greater number of arch wire and the more complex wire bending, causing much difficulty in performing effective treatments. This made me invent Individual Indirect Bonding Technique with the use of multi-purpose set-up model in order to determine a correct and objective bracket position according to individual patients. This technique is more accurate than former indirect bonding techniques in bracket positioning, because it decides the bracket position on a set-up model which has produced to have the occlusal relationship the clinician desired. This technique is especially effective in straight wire appliance and lingual appliance in which the correct bracket positioning is indispensible.

REACH. Major Appliance.

ERIC Educational Resources Information Center

English, Charles; And Others

As a part of the REACH (Refrigeration, Electro-Mechanical, Air-Conditioning, Heating) electromechanical cluster, this student manual contains individualized instructional units in the area of major appliances. The instructional units focus on installation of appliances, troubleshooting washing machines, troubleshooting electric dryers,…

Careers for the 70's In Appliance Repair

ERIC Educational Resources Information Center

Smith, Howard, Ed

1974-01-01

A typical day for an appliance repairman is described to serve as an example and to provide occupational information for a career in appliance repairing. Also, the type of skills needed for this job are described. (DS)

Facilitating Children's Adjustment to Orthotic and Prosthetic Appliances.

ERIC Educational Resources Information Center

Fredrick, Jeff; Fletcher, Donna

1985-01-01

Guidelines are offered to help teachers understand the nature and use of orthotic and prosthetic appliances for disabled students. Classroom behavior observations are noted so that teachers can help monitor the child's adjustment to the appliance. (CL)

Energy and Environment Guide to Action - Chapter 4.4: State Appliance Efficiency Standards

EPA Pesticide Factsheets

Provides recommendations on designing, implementing, and evaluating state appliance efficiency standards. Appliance standards save energy and generate net benefits for homes, businesses, and industry. State success stories are included for reference.

A method of pre-surgical oral orthopaedics.

PubMed

DiBiase, D D; Hunter, S B

1983-01-01

A preliminary report of a technique of pre-surgical treatment in cleft lip and palate patients is outlined utilizing an adjustable intra-oral appliance with extra-oral strapping. The appliance is constructed with an adjustable spring for expansion and two shelves overlapping in the midline to allow palatal continuity during treatment. Frequently, only one appliance for each patient is required. The techniques of appliance construction, pre-surgical management and surgical repair of the lip are outlined.

Maxillary molar derotation and distalization by using a nickel-titanium wire fabricated on a setup model

PubMed Central

Jung, Jong Moon; Wi, Young Joo; Koo, Hyun Mo; Kim, Min Ji

2017-01-01

The purpose of this article is to introduce a simple appliance that uses a setup model and a nickel-titanium (Ni-Ti) wire for correcting the mesial rotation and drift of the permanent maxillary first molar. The technique involves bonding a Ni-Ti wire to the proper position of the target tooth on a setup model, followed by the fabrication of the transfer cap for indirect bonding and its transfer to the patient's teeth. This appliance causes less discomfort and provides better oral hygiene for the patients than do conventional appliances such as the bracket, pendulum, and distal jet. The treatment time is also shorter with the new appliance than with full-fixed appliances. Moreover, the applicability of the new appliance can be expanded to many cases by using screws or splinting with adjacent teeth to improve anchorage. PMID:28670568

Maxillary molar derotation and distalization by using a nickel-titanium wire fabricated on a setup model.

PubMed

Jung, Jong Moon; Wi, Young Joo; Koo, Hyun Mo; Kim, Min Ji; Chun, Youn Sic

2017-07-01

The purpose of this article is to introduce a simple appliance that uses a setup model and a nickel-titanium (Ni-Ti) wire for correcting the mesial rotation and drift of the permanent maxillary first molar. The technique involves bonding a Ni-Ti wire to the proper position of the target tooth on a setup model, followed by the fabrication of the transfer cap for indirect bonding and its transfer to the patient's teeth. This appliance causes less discomfort and provides better oral hygiene for the patients than do conventional appliances such as the bracket, pendulum, and distal jet. The treatment time is also shorter with the new appliance than with full-fixed appliances. Moreover, the applicability of the new appliance can be expanded to many cases by using screws or splinting with adjacent teeth to improve anchorage.

Many small consumers, one growing problem: Achieving energy savings for electronic equipment operating in low power modes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Payne, Christopher T.; Meier, Alan K.

2004-08-24

An increasing amount of electricity is used by equipment that is neither fully ''on'' nor fully ''off.'' We call these equipment states low power modes, or ''lopomos.'' ''Standby'' and ''sleep'' are the most familiar lopomos, but some new products already have many modes. Lopomos are becoming common in household appliances, safety equipment, and miscellaneous products. Ross and Meier (2000) reports that several international studies have found standby power to be as much as 10 percent of residential energy consumption. Lopomo energy consumption is likely to continue growing rapidly as products with lopomos that use significant amounts of energy penetrate themore » market. Other sectors such as commercial buildings and industry also have lopomo energy use, perhaps totaling more in aggregate than that of households, but no comprehensive measurements have been made. In this paper, we propose a research agenda for study of lopomo energy consumption. This agenda has been developed with input from over 200 interested parties. Overall, there is consensus that lopomo energy consumption is an important area for research. Many see this as a critical time for addressing lopomo issues. As equipment designs move from the binary ''on/off'' paradigm to one that encompasses multiple power modes, there is a unique opportunity to address the issue of low power mode energy consumption while technology development paths are still flexible.« less

The Effect of Different Boiling and Filtering Devices on the Concentration of Disinfection By-Products in Tap Water

PubMed Central

Carrasco-Turigas, Glòria; Villanueva, Cristina M.; Goñi, Fernando; Rantakokko, Panu; Nieuwenhuijsen, Mark J.

2013-01-01

Disinfection by-products (DBPs) are ubiquitous contaminants in tap drinking water with the potential to produce adverse health effects. Filtering and boiling tap water can lead to changes in the DBP concentrations and modify the exposure through ingestion. Changes in the concentration of 4 individual trihalomethanes (THM4) (chloroform (TCM), bromodichloromethane (BDCM), dibromochloromethane (DBCM), and bromoform (TBM)), MX, and bromate were tested when boiling and filtering high bromine-containing tap water from Barcelona. For filtering, we used a pitcher-type filter and a household reverse osmosis filter; for boiling, an electric kettle, a saucepan, and a microwave were used. Samples were taken before and after each treatment to determine the change in the DBP concentration. pH, conductivity, and free/total chlorine were also measured. A large decrease of THM4 (from 48% to 97%) and MX concentrations was observed for all experiments. Bromine-containing trihalomethanes were mostly eliminated when filtering while chloroform when boiling. There was a large decrease in the concentration of bromate with reverse osmosis, but there was a little effect in the other experiments. These findings suggest that the exposure to THM4 and MX through ingestion is reduced when using these household appliances, while the decrease of bromate is device dependent. This needs to be considered in the exposure assessment of the epidemiological studies. PMID:23476675

Occlus-o-Guide® versus Andresen activator appliance: neuromuscular evaluation.

PubMed

Farronato, Giampietro; Giannini, Lucia; Galbiati, Guido; Grillo, Elena; Maspero, Cinzia

2013-05-20

The aim of the present study was to assess the muscular variations at the electromyography (EMG) level for the anterior temporalis muscles and masseter muscles during treatment with Occlus-o-Guide® and Andresen activator appliances. Eighty-two patients (35 males and 47 females) aged between 8 and 12 years (mean age, 10.5±0.8 years) participated in the study. Fifty patients underwent treatment with an Occlus-o-Guide® and 32 patients with an Andresen activator. All patients underwent EMG examination using a Freely EMG (De Gotzen, Legnano, Italy) and surface bipolar electrodes when the appliances were worn for the first time (T0), and after 6 months (T1) and after 12 months (T2) of appliance use. Statistical analysis showed that both at T0 and T2, the percent overlapping coefficient (POC) of the anterior temporalis muscles was not statistically different between the appliance groups. At T0, the POC of the masseter muscles was significantly lower for the Andresen appliance as compared to the Occlus-o-Guide® (p=0.02), while at T2 this significance was lost. At insertion of an appliance, all patients show neuromuscular balance that does not correspond to orthognathic occlusion. Both appliances work by creating muscular imbalance. With the appliances in situ, EMG responses were generally analogous for the Occlus-o-Guide® and the Andresen activator; however, the imbalance was greater and the recovery of the orthological muscular balance was slower in patients under treatment with the Andresen activator as compared to those with the Occlus-o-Guide®.

Crew appliance concepts. Volume 3, appendix B: Shuttle orbiter appliances supporting engineering data

NASA Technical Reports Server (NTRS)

Proctor, B. W.; Reysa, R. P.; Russell, D. J.

1975-01-01

Technical data collected for housekeeping, off-duty activities, and medical appliances considered for the shuttle orbiter are presented. Equipment cleaning, refuse management, garment/linen maintenance, entertainment, physical conditioning, sterilization, and physical monitoring were analyzed.

Straight-wire appliances: standard versus individual prescription.

PubMed

Farronato, Giampietro; Periti, Giulia; Giannini, Lucia; Farronato, Davide; Maspero, Cinzia

2009-01-01

In this article the individual patient (IP) appliance is described. It consists of 250 options of bracket and band variations as the straight wire appliances. Increasing the bracket capabilities means using an increasing number of brackets, each with a specific design created for a treatment situation. The objective of IP appliance is to eliminate wire bending from orthodontic treatment and improve the treatment results. To manage this technique, a computer software is needed. Internet offers significant possibilities in managing each patient by patient basis. The clinician is required to make the diagnosis and treatment plan before ordering the appliance. Two clinical cases are described with the aim to present the advantages of this technique.

Treatment effects of the Jasper Jumper and the Bionator associated with fixed appliances.

PubMed

Neves, Leniana Santos; Janson, Guilherme; Cançado, Rodrigo Hermont; de Lima, Karina Jerônimo Rodrigues Santiago; Fernandes, Thaís Maria Freire; Henriques, José Fernando Castanha

2014-01-01

The aim of this study was to evaluate the effects of Class II malocclusion treatment with the Jasper Jumper and the Bionator, associated with fixed appliances. The sample comprised 77 young individuals divided into 3 groups: Group 1 consisted of 25 patients treated with the Jasper Jumper appliance associated with fixed appliances for a mean period of 2.15 years; group 2 had 30 patients, treated with the Bionator and fixed appliances, for a mean treatment time of 3.92 years; and the control group included 22 subjects followed for a mean period of 2.13 years. The initial and final lateral cephalograms of the patients were evaluated. Intergroup comparison at the initial stage and of the treatment changes were performed by analysis of variance. Their effects consisted in a restrictive effect on the maxilla, a slight increase in anterior face height, retrusion and extrusion of the maxillary incisors, labial tipping and protrusion of the mandibular incisors in both groups and intrusion with the Jasper Jumper appliance, maxillary molar distalization with the Jasper Jumper, extrusion and mesialization of the mandibular molars, both appliances provided significant improvement of the maxillomandibular relationship, overjet, overbite and molar relationship. The effects of both appliances in class II malocclusion treatment are similar; however, treatment with the Jasper Jumper was shorter than with the Bionator.

Design and manufacturing of patient-specific orthodontic appliances by computer-aided engineering techniques.

PubMed

Barone, Sandro; Neri, Paolo; Paoli, Alessandro; Razionale, Armando Viviano

2018-01-01

Orthodontic treatments are usually performed using fixed brackets or removable oral appliances, which are traditionally made from alginate impressions and wax registrations. Among removable devices, eruption guidance appliances are used for early orthodontic treatments in order to intercept and prevent malocclusion problems. Commercially available eruption guidance appliances, however, are symmetric devices produced using a few standard sizes. For this reason, they are not able to meet all the specific patient's needs since the actual dental anatomies present various geometries and asymmetric conditions. In this article, a computer-aided design-based methodology for the design and manufacturing of a patient-specific eruption guidance appliances is presented. The proposed approach is based on the digitalization of several steps of the overall process: from the digital reconstruction of patients' anatomies to the manufacturing of customized appliances. A finite element model has been developed to evaluate the temporomandibular joint disks stress level caused by using symmetric eruption guidance appliances with different teeth misalignment conditions. The developed model can then be used to guide the design of a patient-specific appliance with the aim at reducing the patient discomfort. At this purpose, two different customization levels are proposed in order to face both arches and single tooth misalignment issues. A low-cost manufacturing process, based on an additive manufacturing technique, is finally presented and discussed.

[Z2 appliance: the pre-adjusted appliance based on Chinese normal occlusion].

PubMed

Zeng, Xiang-long; Gao, Xue-mei

2008-12-01

Z2 appliance is the pre-adjusted appliance designed for Chinese orthodontic patients. The prescription of the appliance is based on Chinese normal occlusion, which is much different from the West in the first and the second orders as well as the third one. The appliance routinely includes 20 brackets and 8 molar buccal tubers with 3 standard arch forms. Clinically, continued light force is used in whole treatment. The side-effects such as forward tipping of incisors, bite deepening and loss of molar anchorage are reduced further due to fewer tips built into the anterior brackets as well as lower friction elastometric modules used during aligning and leveling. In condition of arch are leveled completely, 0.48 mm x 0.64 mm stainless steel archwire with 1.47 N retraction force is the best combination for sliding mechanics, which is proved by 3D nonlinear finite element study. Self drilling micro-screw is used for maximum anchorage. In finishing stage 0.53 mm x 0.64 mm NT arch wire is added in order to get full torque expressing. The research of Chinese pre-adjusted appliance has been lasted for more than 10 years in the department and clinical studies on Z2 appliance show that with minimal wire bending, treatment is more efficient and result is high quality and more consistent for Chinese orthodontic patients.

Unilateral maxillary molar distalization with zygoma-gear appliance.

PubMed

Kilkis, Dogan; Bayram, Mehmet; Celikoglu, Mevlut; Nur, Metin

2012-08-01

The aim of this study was to present the orthodontic treatment of a 15-year-old boy with a unilateral maxillary molar distalization system, called the zygoma-gear appliance. It consisted of a zygomatic anchorage miniplate, an inner bow, and a Sentalloy closed coil spring (GAC International, Bohemia, NY). A distalizing force of 350 g was used during the distalization period. The unilateral Class II malocclusion was corrected in 5 months with the zygoma-gear appliance. The maxillary left first molar showed distalization of 4 mm with an inclination of 3°. The maxillary premolars moved distally with the help of the transseptal fibers. In addition, there were slight decreases in overjet (-0.5 mm) and maxillary incisor inclination (-1°), indicating no anchorage loss from the zygoma-gear appliance. Preadjusted fixed appliances (0.022 × 0.028-in, MBT system; 3M Unitek, Monrovia, Calif) were placed in both arches to achieve leveling and alignment. After 14 months of unilateral distalization with the zygoma-gear appliance and fixed appliances, Class I molar and canine relationships were established with satisfactory interdigitation of the posterior teeth. Acceptable overjet and overbite were also achieved. This article shows that this new system, the zygoma-gear appliance, can be used for unilateral maxillary molar distalization without anchorage loss. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

46 CFR 199.09 - Equivalents.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS LIFESAVING SYSTEMS FOR..., material, or lifesaving appliance or arrangement, the Commandant (CG-521) may accept any other fitting, material, or lifesaving appliance or arrangement that is at least as effective as that required by this...

Identification of influencing municipal characteristics regarding household waste generation and their forecasting ability in Biscay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oribe-Garcia, Iraia, E-mail: iraia.oribe@deusto.es; Kamara-Esteban, Oihane; Martin, Cristina

Highlights: • We have modelled household waste generation in Biscay municipalities. • We have identified relevant characteristics regarding household waste generation. • Factor models are used in order to identify the best subset of explicative variables. • Biscay’s municipalities are grouped by means of hierarchical clustering. - Abstract: The planning of waste management strategies needs tools to support decisions at all stages of the process. Accurate quantification of the waste to be generated is essential for both the daily management (short-term) and proper design of facilities (long-term). Designing without rigorous knowledge may have serious economic and environmental consequences. The presentmore » works aims at identifying relevant socio-economic features of municipalities regarding Household Waste (HW) generation by means of factor models. Factor models face two main drawbacks, data collection and identifying relevant explanatory variables within a heterogeneous group. Grouping similar characteristics observations within a group may favour the deduction of more robust models. The methodology followed has been tested with Biscay Province because it stands out for having very different municipalities ranging from very rural to urban ones. Two main models are developed, one for the overall province and a second one after clustering the municipalities. The results prove that relating municipalities with specific characteristics, improves the results in a very heterogeneous situation. The methodology has identified urban morphology, tourism activity, level of education and economic situation as the most influencing characteristics in HW generation.« less

A comparison of pain experienced by patients treated with labial and lingual orthodontic appliances.

PubMed

Wu, Abby K Y; McGrath, Colman; Wong, Ricky W K; Wiechmann, D; Rabie, A Bakr M

2010-08-01

The aim of this prospective longitudinal study was to compare pain experiences among Chinese adult patients treated with labial and lingual orthodontic appliances. Sixty patients, 30 with labial appliances (18 females and 12 males, mean age 20.33 years, SD +/- 4.205) and 30 with lingual appliances (22 females and 8 males, mean age 21.63 years, SD +/- 2.236), rated their overall pain experience on a 100 mm visual analogue scale (VAS) at three time points: 1 week (T(1)), 1 month (T(2)), and 3 months (T(3)) after bracket placement. In addition, on a separate 100 mm VAS, they rated their pain experience at the locations of the tongue, lips, cheeks, gums, face, and jaw at T(1), T(2), and T(3). Changes in pain VAS were conducted using Friedman analysis of variance, area under the curve (AUC) analysis and the data were compared using a t-test. There was no significant difference in global ratings of pain among those treated with labial or lingual appliances (P > 0.05). Among both groups, global ratings of pain decreased over the study period (P < 0.001). Patients treated with lingual appliances reported higher ratings of tongue pain (P < 0.001), while those treated with labial appliances reported higher ratings of lip (P < 0.001) and cheek (P < 0.001) pain. The findings indicate that patients treated with labial and lingual appliances rate similarly the level of overall pain they experience during treatment. Ratings of overall pain experienced decreased for both treatment groups with time. However, ratings of pain differed at various sites with respect to the type of orthodontic appliance. These findings have implications in informing patients' treatment decision-making processes regarding labial and lingual appliances and in the management of discomfort associated with different treatment modalities.

Treatment of adolescent patients with class II division 1 malocclusion using Eruption guidance appliance: A comparative study with Twin-block and Activator-Headgear appliances.

PubMed

Nilsson, Jenny Jiayan Luo; Shu, Xiaochen; Magnusson, Britt Hedenberg; Burt, Idil Alatli

2016-01-01

The aim of this study was to evaluate the compliance and short-term effects of eruption guidance appliance (EGA) in adolescents with class II division 1 malocclusion in comparison with twin-block appliance (TBA) and activator-headgear appliance (A-HG). Dental records of 1886 patients were viewed in this retrospective study 129 patients treated with one of these three functional appliances were identified. 123 fulfilled the inclusion criteria and data were extracted from the dental records. Gender, age, compliance, overjet change at every visit, number of appliance breakages and number of emergency visits apart from appliance breakage were studied. The data were analyzed with Chi-square test, General Linear Model and Fisher scoring test. Results showed that 47 patients were treated with EGA, 38 patients with TBA and 38 patients with A-HG. Mean ages starting the treatment were slightly lower with EGA (11.5 years) than with TBA (12.3 years) and A-HG (11.8 years). Non-compliance was higher in the EGA group (31.9%) than TBA group (26.3%) and A-HG group (23.7%). Mean overjet reduction per month was 0.6 mm for EGA which was lower than TBA group (0.7 mm) and A-HG groups (0.7 mm).The number of emergency visits and appliance breakage were lower in EGA group. However, there was no statistically significant difference between the 3 groups regarding ages,compliance, mean overjet reduction, emergency visits and appliance breakage aspects. In conclusion, this study indicates that EGA is an alternative choice in the treatment of adolescent patients with class II division 1 malocclusion. However, long-term follow-up and cephalometric prospective study should be performed to continue our understanding more about the mechanisms of EGA and more definite conclusions can be made.

Effects of different rapid maxillary expansion appliances on facial soft tissues using three-dimensional imaging.

PubMed

Altındiş, Sedat; Toy, Ebubekir; Başçiftçi, Faruk Ayhan

2016-07-01

To determine three-dimensional (3D) effects of three different rapid maxillary expansion (RME) appliances on facial soft tissues. Forty-two children (18 boys, 24 girls) who required RME treatment were included in this study. Patients were randomly divided into three equal groups: banded RME, acrylic splint RME, and modified acrylic splint RME. For each patient, 3D images were obtained before treatment (T1) and at the end of the 3-month retention (T2) with the 3dMD system. When three RME appliances were compared in terms of the effects on the facial soft tissues, there were no significant differences among them. The mouth and nasal width showed a significant increase in all groups. Although the effect of the acrylic splint RME appliances on total face height was less than that of the banded RME, there was no significant difference between the appliances. The effect of the modified acrylic splint appliance on the upper lip was significant according to the volumetric measurements (P < .01). There were no significant differences among three RME appliances on the facial soft tissues. The modified acrylic splint RME produced a more protrusive effect on the upper lip.

Effect of functional appliances on the airway dimensions in patients with skeletal class II malocclusion: A systematic review.

PubMed

Kannan, Annapurna; Sathyanarayana, Haritha Pottipalli; Padmanabhan, Sridevi

2017-01-01

The aim of the present systematic review was to assess the effect of functional appliances on the airway dimensions in patients with skeletal Class II malocclusion. Articles were identified through a literature survey carried out through the following databases: (1) PUBMED, (2) Google Scholar, (3) The Cochrane Library, (4) Embase, (5) Lilac, and (6) Web of Scholars. The systematic review analyzed 12 articles comprising removable functional appliances, 3 articles with fixed functional appliances, and 2 articles having both fixed and removable functional appliances. Qualitative assessment was done for all the 17 studies. The effect of functional appliances in the dimensions of three airway spaces - nasopharynx, oropharynx, and hypopharynx were analyzed. Significant increase in the dimensions of nasopharynx and oropharynx was observed with Activator. Significant increase in the nasopharynx and hypopharynx (male patients) was observed with Bionator. Insignificant increase in the oropharynx was observed with the same. Significant increase in the oropharynx and hypopharynx was observed with Twin Block. Insignificant increase in the nasopharynx was observed with the same. Significant increase was observed only in the hypopharynx for Frankel II. Decreased or insignificant change was observed with FMA, MPA IV, and Herbst appliances.

Distalization of Maxillary First Permanent Molar by Pendulum Appliance in Mixed Dentition Period

PubMed Central

Shetty, Prakashchandra; Anandakrishna, Latha; Rawat, Anuradha

2017-01-01

Introduction Mesial drifting of molar teeth in maxillary arch is corrected by movement of the molars distally. In addition to traditional distal movement techniques, such as extraoral force application and removable appliances, various intra-arch devices have been introduced since 1980s. These intra-arch appliances have nearly eliminated the need for patient cooperation. Case report The purpose of this paper is to report a case of 10-year-old male patient with loss of space in maxillary molar teeth treated by intra-arch appliance-pendulum appliance by distalization of maxillary first permanent molar teeth. Distaliza-tion of the permanent molar teeth helped in proper eruption of second premolar teeth without any extensive treatment procedures. Conclusion In the present case report, the treatment of developing malocclusion was corrected by utilizing the concept of interceptive orthodontics. Hence, correction of space loss in mixed dentition period using pendulum appliance can eliminate the fixed orthodontic therapy. How to cite this article Paranna S, Shetty P, Anandakrishna L, Rawat A. Distalization of Maxillary First Permanent Molar by Pendulum Appliance in Mixed Dentition Period. Int J Clin Pediatr Dent 2017;10(3):299-301. PMID:29104393

Getting into hot water Problematizing hot water service demand: The case of Old Cairo

NASA Astrophysics Data System (ADS)

Culhane, Thomas Henry

This dissertation analyzes hot water demand and service infrastructure in two neighboring but culturally distinct communities of the urban poor in the inner-city area of central Cairo. The communities are the Historic Islamic Cairo neighborhood of Darb Al Ahmar at the foot of Al-Azhar park, and the Zurayib neighborhood of Manshiyat Nasser where the Coptic Zabaleen Recyclers live. The study focuses on the demand side of the hot water issue and involves consideration of built-environment infrastructures providing piped water, electricity, bottled gas, sewage, and the support structures (wiring and plumbing) for consumer durables (appliances such as hot water heaters, stoves, refrigerators, air conditioners) as well as water pumps and water storage tanks. The study asks the questions "How do poor communities in Cairo value hot water" and "How do cost, infrastructure and cultural preferences affect which attributes of hot water service are most highly preferred?". To answer these questions household surveys based primarily on the World Bank LSMS modules were administered by professional survey teams from Darb Al Ahmar's Aga Khan Trust for Culture and the Zabaleen's local NGO "Spirit of Youth" in their adjacent conununities in and surrounding historic Cairo. In total 463 valid surveys were collected, (231 from Darb Al Ahmar, 232 from the Zabaleen). The surveys included a contingent valuation question to explore Willingness to Pay for improved hot water service; the surveys queried household assets as proxies for income. The dissertation's findings reveal that one quarter of the residents of Darb Al Ahmar and two-thirds of the residents of Manshiyet Nasser's Zabaleen lack conventional water heating service. Instead they employ various types of stoves and self-built contraptions to heat water, usually incurring considerable risk and opportunity costs. However the thesis explores the notion that this is rational "satisficing" behavior; despite the shortcomings of such self-help strategies, the greater flexibility they provide may lead to superior long-term outcomes in a time of uncertain and rising energy and commodities prices and an increasing availability of new, less expensive, increasingly modular, and more efficient technologies that are easier for individual households to install and use, especially if the State or non-governmental institutions can provide implementation support. The descriptive statistics and the multivariate models obtained through the analysis of the data gathered in the surveys show that while purchase price and running costs for dedicated water heating systems are considerations for families desiring hot water, the infrastructural demands of modern appliances vis a vis a consumer's given built environment and the historical/cultural legacy of the consumer's past hot water choices and practices are often more important determinants of the kind of water heating used and desired today. Our study shows, for example, that while higher income is associated with owning a water heater in a simple model with few explanatory variables (Model 3) it's significance disappears when controlling for Ethnicity and infrastructural elements (Model 1). This might suggest that while within communities there is a point at which making more money implies a shift to consumer "modernity", overall the availability of more money in these neighborhoods as a whole doesn't guarantee that the utility promised by modern appliances will be realized. A similar point can be made about formal education levels, which appear insignificant in our models. Policy that aimed merely at sending more kids to school would not address the great deficiencies that many Egyptian schools are noted for. There is no guarantee that merely expanding Egypt's "universal education" policy to include children who have fallen through the cracks would help increase consumer awareness or consumer choice. On the other hand both water availability and presence of hot water pipes, as proxies for assets in the built environment, are significant in model 2. With this information about how infrastructure affects consumer choice, and predictors from our models of the average family's willingness to spend discretional income on a new heater, we might suggest that policy aiming at improving the water delivery infrastructure might make a difference. With the right policies enforced, what are now "cold-water flats" could safely, inexpensively and reliably accommodate technologies that provide differentiated water temperatures in separate pipelines. This analysis of consumer choice regarding hot water as a combined water and energy and technological utility contributes to our understanding of redevelopment policy in three ways. First, it provides insights into what is really being valued in terms of amenities at the household level and the self-help strategies people employ to achieve desired end utility. Second, it identifies non-traditional issues, often overlooked in neighborhood improvement scenarios that may help make slum renovation programs more successful. Third, the study reveals the complexities involved in obtaining standard amenities, such as hot water, for low-income groups. Paradoxically, government subsidies for water and energy intended to help the poor may have hurt them by locking them into patterns of behavior which, coupled with architectural decisions sanctioned by the government, severely limit the ability of the poor to take advantage of new opportunities or avoid being constrained by changing conditions at a time of rising energy and resource costs. The findings from this dissertation show that we can not make the assumption that consumers in these areas will move increasingly toward conventional water heating appliances under current conditions; in fact many families have had such units and abandoned them for economic, utility and safety reasons. A rethink is necessary of how government, the private sector, NGOs and individual households can work together to guarantee that safe, reliable and economical hot water is provided to every family.

16 CFR 1406.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... BURNING APPLIANCES-NOTIFICATION OF PERFORMANCE AND TECHNICAL DATA § 1406.3 Definitions. For the purposes of this rule: (a) Coal and wood burning appliances means fireplace stoves, room heater/fireplace... chimney flue. (e) Cookstoves and ranges are chimney connected solid fuel burning appliances that are used...

16 CFR 1406.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... BURNING APPLIANCES-NOTIFICATION OF PERFORMANCE AND TECHNICAL DATA § 1406.3 Definitions. For the purposes of this rule: (a) Coal and wood burning appliances means fireplace stoves, room heater/fireplace... chimney flue. (e) Cookstoves and ranges are chimney connected solid fuel burning appliances that are used...

Hydrophilic structures for condensation management in refrigerator appliances

DOEpatents

Kuehl, Steven John; Vonderhaar, John J; Wu, Guolian; Wu, Mianxue

2014-10-21

A refrigerator appliance that includes a freezer compartment having a freezer compartment door, and a refrigeration compartment having at least one refrigeration compartment door. The appliance further includes a mullion with an exterior surface. The mullion divides the compartments and the exterior surface directs condensation toward a transfer point. The appliance may also include a cabinet that houses the compartments and has two sides, each with an exterior surface. Further, at least one exterior surface directs condensation toward a transfer point.

Multi-agent modelling of climate outlooks and food security on a community garden scheme in Limpopo, South Africa.

PubMed

Bharwani, Sukaina; Bithell, Mike; Downing, Thomas E; New, Mark; Washington, Richard; Ziervogel, Gina

2005-11-29

Seasonal climate outlooks provide one tool to help decision-makers allocate resources in anticipation of poor, fair or good seasons. The aim of the 'Climate Outlooks and Agent-Based Simulation of Adaptation in South Africa' project has been to investigate whether individuals, who adapt gradually to annual climate variability, are better equipped to respond to longer-term climate variability and change in a sustainable manner. Seasonal climate outlooks provide information on expected annual rainfall and thus can be used to adjust seasonal agricultural strategies to respond to expected climate conditions. A case study of smallholder farmers in a village in Vhembe district, Limpopo Province, South Africa has been used to examine how such climate outlooks might influence agricultural strategies and how this climate information can be improved to be more useful to farmers. Empirical field data has been collected using surveys, participatory approaches and computer-based knowledge elicitation tools to investigate the drivers of decision-making with a focus on the role of climate, market and livelihood needs. This data is used in an agent-based social simulation which incorporates household agents with varying adaptation options which result in differing impacts on crop yields and thus food security, as a result of using or ignoring the seasonal outlook. Key variables are the skill of the forecast, the social communication of the forecast and the range of available household and community-based risk coping strategies. This research provides a novel approach for exploring adaptation within the context of climate change.

To explore preferences and willingness to pay for attributes regarding stoma appliances amongst patients in the UK, France and Germany.

PubMed

Nafees, Beenish; Lloyd, Andrew; Elkin, Eric; Porret, Terri

2015-04-01

To explore patient preferences regarding stoma appliances in the UK, France and Germany and to estimate willingness to pay (WTP) for attributes of stoma appliances. A discrete choice (DCE) survey was developed based on published literature, attributes of current available appliances and qualitative interviews with patients from the UK (N = 3), France (N = 2) and Germany (N = 2). Members from a patient panel in the UK, France and Germany were asked to participate in the DCE survey and to fill out two quality of life (QoL) questionnaires. Data were analyzed using the conditional logit model whereby the coefficients obtained from the model provided an estimate of the (log) odds ratios (ORs) of preference for attributes. WTP was estimated for each level of a given identified attribute. Seven key attributes were identified for the DCE survey: comfort and elastic flexibility, skin problems, early detection of leakage, leakage, filter performance, service/help after hospital discharge and out-of-pocket cost. A total of 415 participants (166 patients in UK, 99 in France, and 150 in Germany) completed the questionnaires. All attributes were significant predictors of choice. The two most important drivers of preference were the attributes comfort and elastic flexibility and skin problems which resulted in high WTP values. Appliances which were able to detect episodes of leakage were also of high importance to participants' appliances. The results show the importance of different attributes of stoma appliances for patients. Improving comfort and elastic flexibility, and risk of skin problems were the most important aspects of appliances. The WTP values indicate the value people place on improvement in each attribute of appliances.

Four novel prosthodontic methods for managing upper airway resistance syndrome: an investigative analysis revealing the efficacy of the new nasopharyngeal aperture guard appliance.

PubMed

Venkat, R; Gopichander, N; Vasantakumar, M

2010-01-01

Obstructive sleep apnea is the most frequent cause for insomnia in the populace. Snoring is mulled over as the potential factor that can lead the sequel to obstructive sleep apnea. Although the etiology and deterrence measures for snoring are yet to be undoubtedly clarified by our scientific sorority, various means of surgical corrections have been affirmed and put into practice, with a substantial degree of success. Despite this, it is implicit that a noninvasive method of managing obstructive sleep apnea is more relevant for overcoming this condition. This manuscript intends to establish how snoring can be controlled prosthodontically by different modalities of scientifically defensible approaches. The most effective among the modalities was affirmed as the investigative analyses of the treatment outcomes with each modality. NOVEL METHODS: Four new methods of managing obstructive sleep apnea--uvula lift appliance, uvula and velopharynx lift appliance, nasopharyngeal aperture guard, and soft palate lift appliance were demonstrated through this article. The four new modalities stated and one conventional modality of mandibular advancement appliance for managing obstructive sleep apnea, a total of five types of appliance therapies, were described with case reports for each. Five individuals undergoing the appliance therapy were chosen for each modality. The treatment outcome with each modality was examined by analysis of clinical predictors and also by means of standard investigation, with nasal and oral endoscopic analyses. Among the five types of appliance therapies, the nasopharyngeal aperture guard provided the best treatment outcome in terms of clinical predictors and endoscopic analyses. Nasopharyngeal aperture guard, the novel method stated in this article is the better modality for managing obstructive sleep apnea, among the five different appliance therapies.

Occlus-o-Guide® versus Andresen activator appliance: neuromuscular evaluation

PubMed Central

2013-01-01

Background The aim of the present study was to assess the muscular variations at the electromyography (EMG) level for the anterior temporalis muscles and masseter muscles during treatment with Occlus-o-Guide® and Andresen activator appliances. Methods Eighty-two patients (35 males and 47 females) aged between 8 and 12 years (mean age, 10.5 ± 0.8 years) participated in the study. Fifty patients underwent treatment with an Occlus-o-Guide® and 32 patients with an Andresen activator. All patients underwent EMG examination using a Freely EMG (De Gotzen, Legnano, Italy) and surface bipolar electrodes when the appliances were worn for the first time (T0), and after 6 months (T1) and after 12 months (T2) of appliance use. Results Statistical analysis showed that both at T0 and T2, the percent overlapping coefficient (POC) of the anterior temporalis muscles was not statistically different between the appliance groups. At T0, the POC of the masseter muscles was significantly lower for the Andresen appliance as compared to the Occlus-o-Guide® (p = 0.02), while at T2 this significance was lost. Conclusions At insertion of an appliance, all patients show neuromuscular balance that does not correspond to orthognathic occlusion. Both appliances work by creating muscular imbalance. With the appliances in situ, EMG responses were generally analogous for the Occlus-o-Guide® and the Andresen activator; however, the imbalance was greater and the recovery of the orthological muscular balance was slower in patients under treatment with the Andresen activator as compared to those with the Occlus-o-Guide®. PMID:24325935

Esthetic perception of orthodontic appliances by Brazilian children and adolescents.

PubMed

Kuhlman, Deise Caldas; Lima, Tatiana Araújo de; Duplat, Candice Belchior; Capelli, Jonas

2016-01-01

The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276) was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those with higher economic status, golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures were assessed as the worst esthetic option.

Esthetic perception of orthodontic appliances by Brazilian children and adolescents

PubMed Central

Kuhlman, Deise Caldas; de Lima, Tatiana Araújo; Duplat, Candice Belchior; Capelli, Jonas

2016-01-01

ABSTRACT Objective: The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. Methods: A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276) was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Results: Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Conclusion: Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those with higher economic status, golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures were assessed as the worst esthetic option. PMID:27901230

14 CFR 25.1365 - Electrical appliances, motors, and transformers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... transformers. 25.1365 Section 25.1365 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Equipment § 25.1365 Electrical appliances, motors, and transformers. (a) Domestic appliances must be... transformers, including those installed in domestic systems, must have a suitable thermal protection device to...

14 CFR 25.1365 - Electrical appliances, motors, and transformers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... transformers. 25.1365 Section 25.1365 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Equipment § 25.1365 Electrical appliances, motors, and transformers. (a) Domestic appliances must be... transformers, including those installed in domestic systems, must have a suitable thermal protection device to...

14 CFR 25.1365 - Electrical appliances, motors, and transformers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... transformers. 25.1365 Section 25.1365 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Equipment § 25.1365 Electrical appliances, motors, and transformers. (a) Domestic appliances must be... transformers, including those installed in domestic systems, must have a suitable thermal protection device to...

14 CFR 25.1365 - Electrical appliances, motors, and transformers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... transformers. 25.1365 Section 25.1365 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Equipment § 25.1365 Electrical appliances, motors, and transformers. (a) Domestic appliances must be... transformers, including those installed in domestic systems, must have a suitable thermal protection device to...

14 CFR 25.1365 - Electrical appliances, motors, and transformers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... transformers. 25.1365 Section 25.1365 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Equipment § 25.1365 Electrical appliances, motors, and transformers. (a) Domestic appliances must be... transformers, including those installed in domestic systems, must have a suitable thermal protection device to...

16 CFR § 1406.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... BURNING APPLIANCES-NOTIFICATION OF PERFORMANCE AND TECHNICAL DATA § 1406.3 Definitions. For the purposes of this rule: (a) Coal and wood burning appliances means fireplace stoves, room heater/fireplace... chimney flue. (e) Cookstoves and ranges are chimney connected solid fuel burning appliances that are used...

Face and neck dermatitis from a stainless steel orthodontic appliance.

PubMed

Ehrnrooth, Minna; Kerosuo, Heidi

2009-11-01

Although nickel is the most common cause of contact allergy, nickel-containing orthodontic appliances seldom cause adverse reactions that result in discontinuation of treatment. We report on an eruption of dermatitis in the face and neck of an adult female patient after placement of a rapid maxillary expansion appliance (RME). Because the patient suspected nickel allergy, her tolerance to the appliance material was tested intraorally before treatment by cementing bands on four teeth for a week. No visible adverse reactions were seen during the test. One week after cementation of the RME appliance, the patient reported strong itching of the face and a red rash. Clinical examination showed itchy papular erythema on the face and neck. No intraoral reactions or symptoms were present. The RME appliance was removed, and symptoms disappeared in 4 to 5 days. The patient was referred for a nickel patch test, which gave a strong positive result. Adverse patient reactions of potential allergic origin should be diagnosed carefully, and their possible impact on further treatment should be evaluated accordingly.

Pendulum and modified pendulum appliances for maxillary molar distalization in Class II malocclusion - a systematic review.

PubMed

Al-Thomali, Yousef; Basha, Sakeenabi; Mohamed, Roshan Noor

2017-08-01

The main purpose of the present systematic review was to evaluate the quantitative effects of the pendulum appliance and modified pendulum appliances for maxillary molar distalization in Class II malocclusion. Our systematic search included MEDLINE, EMBASE, CINAHL, PsychINFO, Scopus and key journals and review articles; the date of the last search was 30 January 2017. We graded the methodological quality of the studies by means of the Quality Assessment Tool for Quantitative Studies, developed for the Effective Public Health Practice Project (EPHPP). In total, 203 studies were identified for screening, and 25 studies were eligible. The quality assessment rated four (16%) of the study as being of strong quality and 21 (84%) of these studies as being of moderate quality. The pendulum appliances showed mean molar distalization of 2-6.4 mm, distal tipping of molars from 6.67° to 14.50° and anchorage loss with mean premolar and incisor mesial movement of 1.63-3.6 mm and 0.9-6.5 mm, respectively. The bone anchored pendulum appliances (BAPAs) showed mean molar distalization of 4.8-6.4 mm, distal tipping of molars from 9° to 11.3° and mean premolar distalization of 2.7-5.4 mm. Pendulum and modified pendulum appliances are effective in molar distalization. Pendulum appliance with K-loop modification, implant supported pendulum appliance and BAPA significantly reduced anchorage loss of the anterior teeth and distal tipping of the molar teeth.

77 FR 48504 - Submission for OMB Review; Comment Request-Coal and Woodburning Appliances

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-14

... Request--Coal and Woodburning Appliances AGENCY: Consumer Product Safety Commission. ACTION: Notice... collection of information for regulations on coal and woodburning appliances. No comments were received in...: Request for Reinstatement of Approval of Collection of Information. Existing manufacturers of coal and...

46 CFR 109.209 - Appliances for watertight integrity.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Appliances for watertight integrity. 109.209 Section 109.209 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Tests, Drills, and Inspections § 109.209 Appliances for watertight integrity. (a) Before getting...

46 CFR 109.209 - Appliances for watertight integrity.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 109.209 Section 109.209 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Tests, Drills, and Inspections § 109.209 Appliances for watertight integrity. (a) Before getting...

46 CFR 109.209 - Appliances for watertight integrity.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Appliances for watertight integrity. 109.209 Section 109.209 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Tests, Drills, and Inspections § 109.209 Appliances for watertight integrity. (a) Before getting...

46 CFR 109.209 - Appliances for watertight integrity.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Appliances for watertight integrity. 109.209 Section 109.209 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Tests, Drills, and Inspections § 109.209 Appliances for watertight integrity. (a) Before getting...

46 CFR 109.209 - Appliances for watertight integrity.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Appliances for watertight integrity. 109.209 Section 109.209 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS OPERATIONS Tests, Drills, and Inspections § 109.209 Appliances for watertight integrity. (a) Before getting...

46 CFR 108.645 - Markings on lifesaving appliances.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Markings on lifesaving appliances. 108.645 Section 108.645 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.645 Markings on lifesaving appliances. (a...

46 CFR 108.665 - Appliances for watertight integrity.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 108.665 Section 108.665 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.665 Appliances for watertight integrity...

76 FR 52917 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Adoption of Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-24

... Large Appliance and Metal Furniture Coatings AGENCY: Environmental Protection Agency (EPA). ACTION... Techniques Guidelines (CTG) standards for large appliance and metal furniture coatings. In the Final Rules...; Pennsylvania; Adoption of Control Techniques Guidelines for Large Appliance and Metal Furniture Coatings...

42 CFR 409.25 - Drugs, biologicals, supplies, appliances, and equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 2 2011-10-01 2011-10-01 false Drugs, biologicals, supplies, appliances, and... Drugs, biologicals, supplies, appliances, and equipment. (a) Drugs and biologicals. Except as specified in paragraph (b) of this section, Medicare pays for drugs and biologicals as posthospital SNF care...

42 CFR 409.25 - Drugs, biologicals, supplies, appliances, and equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Drugs, biologicals, supplies, appliances, and... Drugs, biologicals, supplies, appliances, and equipment. (a) Drugs and biologicals. Except as specified in paragraph (b) of this section, Medicare pays for drugs and biologicals as posthospital SNF care...

46 CFR 133.170 - Line-throwing appliance.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Line-throwing appliance. 133.170 Section 133.170 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS LIFESAVING SYSTEMS Requirements for All OSVs § 133.170 Line-throwing appliance. (a) General. Each OSV must have a...

46 CFR 133.170 - Line-throwing appliance.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Line-throwing appliance. 133.170 Section 133.170 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS LIFESAVING SYSTEMS Requirements for All OSVs § 133.170 Line-throwing appliance. (a) General. Each OSV must have a...

14 CFR 49.53 - Eligibility for recording: general requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Aircraft Engines, Propellers, Appliances, and Spare Parts § 49.53 Eligibility for recording: general... engine, propeller, appliance, or spare part, maintained by or on behalf of an air carrier certificated... need only describe generally, by type, the engines, propellers, appliances, or spare parts covered by...

14 CFR 49.53 - Eligibility for recording: general requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Aircraft Engines, Propellers, Appliances, and Spare Parts § 49.53 Eligibility for recording: general... engine, propeller, appliance, or spare part, maintained by or on behalf of an air carrier certificated... need only describe generally, by type, the engines, propellers, appliances, or spare parts covered by...

14 CFR 49.53 - Eligibility for recording: general requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Aircraft Engines, Propellers, Appliances, and Spare Parts § 49.53 Eligibility for recording: general... engine, propeller, appliance, or spare part, maintained by or on behalf of an air carrier certificated... need only describe generally, by type, the engines, propellers, appliances, or spare parts covered by...

14 CFR 49.53 - Eligibility for recording: general requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Aircraft Engines, Propellers, Appliances, and Spare Parts § 49.53 Eligibility for recording: general... engine, propeller, appliance, or spare part, maintained by or on behalf of an air carrier certificated... need only describe generally, by type, the engines, propellers, appliances, or spare parts covered by...

14 CFR 49.53 - Eligibility for recording: general requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Aircraft Engines, Propellers, Appliances, and Spare Parts § 49.53 Eligibility for recording: general... engine, propeller, appliance, or spare part, maintained by or on behalf of an air carrier certificated... need only describe generally, by type, the engines, propellers, appliances, or spare parts covered by...

24 CFR 3285.904 - Utility system connections.

Code of Federal Regulations, 2013 CFR

2013-04-01

... must convert the appliance from one type of gas to another, following instructions by the manufacturer... type of gas to be supplied. (3) Connection procedures. Gas-burning appliance vents must be inspected to... concerning the following gas appliance startup procedures: (i) One at a time, opening equipment shutoff...

24 CFR 3285.904 - Utility system connections.

Code of Federal Regulations, 2012 CFR

2012-04-01

... must convert the appliance from one type of gas to another, following instructions by the manufacturer... type of gas to be supplied. (3) Connection procedures. Gas-burning appliance vents must be inspected to... concerning the following gas appliance startup procedures: (i) One at a time, opening equipment shutoff...

24 CFR 3285.904 - Utility system connections.

Code of Federal Regulations, 2014 CFR

2014-04-01

... must convert the appliance from one type of gas to another, following instructions by the manufacturer... type of gas to be supplied. (3) Connection procedures. Gas-burning appliance vents must be inspected to... concerning the following gas appliance startup procedures: (i) One at a time, opening equipment shutoff...

46 CFR 160.040-3 - Materials, construction, workmanship, and performance requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Appliance, Impulse-Projected Rocket Type (and Equipment) § 160.040-3 Materials, construction, workmanship...-projected rocket type line-throwing appliances and equipment shall be of good quality suitable for the... operation aboard vessels at sea. (c) Workmanship. Impulse-projected rocket type line-throwing appliances...

46 CFR 160.040-3 - Materials, construction, workmanship, and performance requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Appliance, Impulse-Projected Rocket Type (and Equipment) § 160.040-3 Materials, construction, workmanship...-projected rocket type line-throwing appliances and equipment shall be of good quality suitable for the... operation aboard vessels at sea. (c) Workmanship. Impulse-projected rocket type line-throwing appliances...

46 CFR 160.040-3 - Materials, construction, workmanship, and performance requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Appliance, Impulse-Projected Rocket Type (and Equipment) § 160.040-3 Materials, construction, workmanship...-projected rocket type line-throwing appliances and equipment shall be of good quality suitable for the... operation aboard vessels at sea. (c) Workmanship. Impulse-projected rocket type line-throwing appliances...

46 CFR 160.040-3 - Materials, construction, workmanship, and performance requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Appliance, Impulse-Projected Rocket Type (and Equipment) § 160.040-3 Materials, construction, workmanship...-projected rocket type line-throwing appliances and equipment shall be of good quality suitable for the... operation aboard vessels at sea. (c) Workmanship. Impulse-projected rocket type line-throwing appliances...

46 CFR 160.040-3 - Materials, construction, workmanship, and performance requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Appliance, Impulse-Projected Rocket Type (and Equipment) § 160.040-3 Materials, construction, workmanship...-projected rocket type line-throwing appliances and equipment shall be of good quality suitable for the... operation aboard vessels at sea. (c) Workmanship. Impulse-projected rocket type line-throwing appliances...

Fixed or removable function appliances for Class II malocclusions.

PubMed

Madurantakam, Parthasarathy

2016-06-01

Data sourcesEmbase, Cochrane Central Register of Controlled Trials, Medline (Pubmed), Web of Science, Google Scholar, Scopus, LILACS database and bibliographies of clinical trials encountered during search. There was no restriction on language or date during search.Study selectionRandomised Controlled Trials (RCTs) and Controlled Clinical Trials (CCT) in patients with Class II malocclusions that compared at least one fixed functional appliance with at least one removable functional appliance (RFA) in children below 16 years of age. Primary outcomes were clinical and lateral cephalometric measurements and the duration of treatment. Secondary outcomes included patient experiences of treatment, quality of life measures and harms arising during treatment as well as costs of both treatments.Data extraction and synthesisThe titles and abstracts of all studies identified through the search were assessed independently and in duplicate by two review authors. Disagreements about included studies were resolved through discussion with the third author. Heterogeneity was assessed using customised forms and risk of bias using a Cochrane Collaboration tool. A meta-analysis was planned for studies at low risk of bias with similar comparisons reporting the same outcome.ResultsTwo RCTs and two CCTs that met the inclusion/exclusion criteria were included in the final analysis. Risk of bias assessment indicated three trials were at high risk while one was unclear. Consequently, the included trials were deemed to be inappropriate for meta-analysis (MA).Two studies with 282 participants evaluated Twin Block with fixed Herbst appliance and reported significant improvements in anterior-posterior skeletal discrepancy, mandibular length and reduction of overjet with both appliances. While one study reported significantly shorter treatment duration in Herbst appliance, the other study did not find any difference. Herbst appliance had better compliance, less dropouts but more emergency visits.One trial that compared activator appliance with Twin Force Bite Corrector found significantly shorter time with the fixed appliance. However, effective length and sagittal positioning of the mandible was not different between the groups.One trial comparing activator with Forsus FRZ reported enhanced mandibular growth and restrained maxillary growth with both the appliances. While activator appliance was associated with increased posterior facial height, Forsus significantly rotated the occlusal plane.ConclusionsLimited available evidence indicates that both fixed and removable functional appliances are effective in reducing overjet in growing children. However, there is insufficient evidence to differentiate between the two types with respect to biological (skeletal and dental) effects or patient experiences.

Changes in the oral environment after placement of lingual and labial orthodontic appliances.

PubMed

Lombardo, Luca; Ortan, Yildiz Öztürk; Gorgun, Özge; Panza, Chiara; Scuzzo, Giuseppe; Siciliani, Giuseppe

2013-09-11

This study compared the oral hygiene and caries risk of patients treated with labial and lingual orthodontic appliances throughout a prospective evaluation of the status of the oral environment before and after bracket placement. A total of 20 orthodontic patients aged 19 to 23 years were included in the study and were divided into two groups: 10 patients wore Roth labial appliance (American Orthodontics, Sheboygan, WI, USA) and 10 patients wore STb lingual appliance (Ormco Corporation, Glendora, CA, USA). Plaque index (PI), gingival bleeding index (GBI), salivary flow rate, saliva buffer capacity, salivary pH, and Streptococcus mutans and Lactobacillus counts in saliva were determined at three time points: before orthodontic appliance placement (T0), 4 weeks after bonding (T1), and 8 weeks after bonding (T2). After appliance placement, all patients were periodically educated to the oral hygiene procedures. Wilcoxon rank and Mann-Whitney U tests were used to determine intragroup and intergroup differences as regards qualitative data. To compare quantitative data between the groups, chi-square and Fisher's exact tests were undertaken, while intragroup differences were tested with McNemar test. The level of statistical significance was set at p<0.05. Statistical analysis of the data obtained revealed a statistically significant difference between the data of T0 and T1 and the data of T0 and T2 of the PI scores and between T0 and T2 of the GBI scores in the group treated with the lingual appliance. The GBI value increased significantly between T0 and T1 but decreased significantly between T1 and T2 (p<0.01) in the group treated with labial appliance. S. mutans counts increased significantly between T0 and T2 in the saliva samples of patients treated with lingual appliance. No statistically significant differences were found between S. mutans and Lactobacillus counts at the three terms of saliva collection in patients treated with labial appliance. No statistically significant differences were found between the two groups at the three time points as regards the salivary flow rate and saliva buffer capacity. Lingual and labial orthodontic appliances showed a different potential in modifying the investigated clinical parameters: patients wearing STb lingual orthodontic appliance had more plaque retention 4 and 8 weeks after bonding, while there were more gingival inflammation and more S. mutans counts 8 weeks after bonding. No differences were found between the two groups as regards the Lactobacillus counts, the salivary flow rate, and saliva buffer capacity.

Bisphenol A emission factors from industrial sources and elimination rates in a sewage treatment plant.

PubMed

Fuerhacker, M

2003-01-01

Bisphenol A (BPA) is widely used for the production of epoxy resins and polycarbonate plastics and is considered an endocrine disruptor. Special in vitro test systems and animal experiments showed a weak estrogenic activity. Aquatic wildlife especially could be endangered by waste water discharges. To manage possible risks arising from BPA emissions the major fluxes need to be investigated and the sources of the contamination of municipal treatment plants need to be determined. In this study, five major industrial point sources, two different household areas and the influent and effluent of the corresponding treatment plant (WWTP) were monitored simultaneously at a plant serving 120,000 population equivalents. A paper producing plant was the major BPA contributor to the influent load of the wastewater treatment plant. All the other emissions from point sources, including the two household areas, were considerably lower. The minimum elimination rate in the WTTP could be determined at 78% with an average of 89% of the total BPA-load. For a possible pollution-forecast, or for a comparison between different point sources, emission factors based on COD-emissions were calculated for industrial and household point sources at BPA/COD-ratios between 1.4 x 10(-8) - 125 x 10(-8) and 1.3 x 10(-6) - 6.3 x 10(-6), respectively.

49 CFR 236.312 - Movable bridge, interlocking of signal appliances with bridge devices.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Movable bridge, interlocking of signal appliances with bridge devices. 236.312 Section 236.312 Transportation Other Regulations Relating to... SYSTEMS, DEVICES, AND APPLIANCES Interlocking Standards § 236.312 Movable bridge, interlocking of signal...

49 CFR 238.429 - Safety appliances.

Code of Federal Regulations, 2012 CFR

2012-10-01

... appliance mechanical strength and fasteners. (1) All handrails, handholds, and sill steps shall be made of 1-inch diameter steel pipe, 5/8-inch thickness steel, or a material of equal or greater mechanical strength. (2) All safety appliances shall be securely fastened to the car body structure with mechanical...

21 CFR 888.3030 - Single/multiple component metallic bone fixation appliances and accessories.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Single/multiple component metallic bone fixation....3030 Single/multiple component metallic bone fixation appliances and accessories. (a) Identification. Single/multiple component metallic bone fixation appliances and accessories are devices intended to be...

21 CFR 888.3030 - Single/multiple component metallic bone fixation appliances and accessories.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Single/multiple component metallic bone fixation....3030 Single/multiple component metallic bone fixation appliances and accessories. (a) Identification. Single/multiple component metallic bone fixation appliances and accessories are devices intended to be...

21 CFR 888.3030 - Single/multiple component metallic bone fixation appliances and accessories.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Single/multiple component metallic bone fixation....3030 Single/multiple component metallic bone fixation appliances and accessories. (a) Identification. Single/multiple component metallic bone fixation appliances and accessories are devices intended to be...

21 CFR 888.3030 - Single/multiple component metallic bone fixation appliances and accessories.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Single/multiple component metallic bone fixation....3030 Single/multiple component metallic bone fixation appliances and accessories. (a) Identification. Single/multiple component metallic bone fixation appliances and accessories are devices intended to be...

21 CFR 888.3030 - Single/multiple component metallic bone fixation appliances and accessories.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Single/multiple component metallic bone fixation....3030 Single/multiple component metallic bone fixation appliances and accessories. (a) Identification. Single/multiple component metallic bone fixation appliances and accessories are devices intended to be...

24 CFR 3280.811 - Calculations.

Code of Federal Regulations, 2011 CFR

2011-04-01

... appliance receptacle circuit (see definition of “Appliance Portable” with Note): e.g. Number of circuits × 1..., wall-mounted oven, cooking units. Where number of these appliances exceeds three, use 75 percent of... neutral load determined by Article 220.61 of the National Electrical Code, NFPA No. 70-2005. The loads...

78 FR 35894 - Notice of Petition for Waiver of Panasonic Appliances Refrigeration Systems Corporation of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-14

... Petition for Waiver of Panasonic Appliances Refrigeration Systems Corporation of America Corporation... Panasonic Appliances Refrigeration Systems Corporation of America (PAPRSA) seeking an exemption from... Refrigeration Systems Corporation of America, meaning that it is the same manufacturer to which DOE granted the...

77 FR 234 - Rule Concerning Disclosures Regarding Energy Consumption and Water Use of Certain Home Appliances...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-04

... FEDERAL TRADE COMMISSION 16 CFR Part 305 RIN 3084-AB03 Rule Concerning Disclosures Regarding Energy Consumption and Water Use of Certain Home Appliances and Other Products Required Under the Energy Policy and Conservation Act (``Appliance Labeling Rule'') AGENCY: Federal Trade Commission. ACTION...

3 CFR - Appliance Efficiency Standards

Code of Federal Regulations, 2010 CFR

2010-01-01

... 3 The President 1 2010-01-01 2010-01-01 false Appliance Efficiency Standards Presidential Documents Other Presidential Documents Memorandum of February 5, 2009 Appliance Efficiency Standards Memorandum for the Secretary of Energy Under the Energy Policy and Conservation Act of 1975 (EPCA), the Department of Energy (DOE) is required to establish...

14 CFR Appendix B to Part 43 - Recording of Major Repairs and Major Alterations

Code of Federal Regulations, 2014 CFR

2014-01-01

..., within 48 hours after the aircraft, airframe, aircraft engine, propeller, or appliance is approved for... approval for return to service of the aircraft, airframe, aircraft engine, propeller, or appliance; (3... engine, propeller or appliance. (ii) If an aircraft, the make, model, serial number, nationality and...

14 CFR Appendix B to Part 43 - Recording of Major Repairs and Major Alterations

Code of Federal Regulations, 2011 CFR

2011-01-01

..., within 48 hours after the aircraft, airframe, aircraft engine, propeller, or appliance is approved for... approval for return to service of the aircraft, airframe, aircraft engine, propeller, or appliance; (3... engine, propeller or appliance. (ii) If an aircraft, the make, model, serial number, nationality and...

14 CFR Appendix B to Part 43 - Recording of Major Repairs and Major Alterations

Code of Federal Regulations, 2010 CFR

2010-01-01

..., within 48 hours after the aircraft, airframe, aircraft engine, propeller, or appliance is approved for... approval for return to service of the aircraft, airframe, aircraft engine, propeller, or appliance; (3... engine, propeller or appliance. (ii) If an aircraft, the make, model, serial number, nationality and...

14 CFR Appendix B to Part 43 - Recording of Major Repairs and Major Alterations

Code of Federal Regulations, 2012 CFR

2012-01-01

..., within 48 hours after the aircraft, airframe, aircraft engine, propeller, or appliance is approved for... approval for return to service of the aircraft, airframe, aircraft engine, propeller, or appliance; (3... engine, propeller or appliance. (ii) If an aircraft, the make, model, serial number, nationality and...

78 FR 54450 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-04

... Shelving and Racks From the People's Republic of China: Preliminary Results of Antidumping Duty... the antidumping duty order on certain kitchen appliance shelving and racks from the People's Republic...\\ is certain kitchen appliance shelving and racks. The subject merchandise is currently classifiable...

Major Appliance Repair. Teacher Edition.

ERIC Educational Resources Information Center

Smreker, Eugene; Calvert, King

This module is a comprehensive text on basic appliance repair, designed to prepare students for entry-level jobs in this growing field. Ensuring a firm grounding in electrical knowledge, the module contains 13 instructional units that cover the following topics: (1) major appliance repair orientation; (2) safety and first aid; (3) fundamentals of…

16 CFR 1406.1 - Scope, purpose, and effective date.

Code of Federal Regulations, 2012 CFR

2012-01-01

... REGULATIONS COAL AND WOOD BURNING APPLIANCES-NOTIFICATION OF PERFORMANCE AND TECHNICAL DATA § 1406.1 Scope... coal and wood burning appliances, as defined in § 1406.3(a), to provide consumers with a specified... information provided with coal and wood burning appliances. This rule does not replace any voluntary standards...

16 CFR 1406.1 - Scope, purpose, and effective date.

Code of Federal Regulations, 2014 CFR

2014-01-01

... REGULATIONS COAL AND WOOD BURNING APPLIANCES-NOTIFICATION OF PERFORMANCE AND TECHNICAL DATA § 1406.1 Scope... coal and wood burning appliances, as defined in § 1406.3(a), to provide consumers with a specified... information provided with coal and wood burning appliances. This rule does not replace any voluntary standards...

75 FR 81555 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Allegheny County's...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

... Techniques Guidelines for Large Appliance and Metal Furniture; Flat Wood Paneling; Paper, Film, and Foil... appliance and metal furniture; flat wood paneling; and paper, film, and foil surface coating processes. In... Control Techniques Guidelines for Large Appliance and Metal Furniture; Flat Wood Paneling; Paper, Film...

16 CFR 1406.1 - Scope, purpose, and effective date.

Code of Federal Regulations, 2011 CFR

2011-01-01

... REGULATIONS COAL AND WOOD BURNING APPLIANCES-NOTIFICATION OF PERFORMANCE AND TECHNICAL DATA § 1406.1 Scope... coal and wood burning appliances, as defined in § 1406.3(a), to provide consumers with a specified... information provided with coal and wood burning appliances. This rule does not replace any voluntary standards...

16 CFR 1406.1 - Scope, purpose, and effective date.

Code of Federal Regulations, 2010 CFR

2010-01-01

... REGULATIONS COAL AND WOOD BURNING APPLIANCES-NOTIFICATION OF PERFORMANCE AND TECHNICAL DATA § 1406.1 Scope... coal and wood burning appliances, as defined in § 1406.3(a), to provide consumers with a specified... information provided with coal and wood burning appliances. This rule does not replace any voluntary standards...

49 CFR 236.312 - Movable bridge, interlocking of signal appliances with bridge devices.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Movable bridge, interlocking of signal appliances with bridge devices. 236.312 Section 236.312 Transportation Other Regulations Relating to... SYSTEMS, DEVICES, AND APPLIANCES Interlocking Standards § 236.312 Movable bridge, interlocking of signal...

15 CFR 9.4 - Development of voluntary energy conservation specifications.

Code of Federal Regulations, 2010 CFR

2010-01-01

... efficiency characteristics of the class of appliance or equipment. (3) A prototype Label and directions for... conditions of use, and stating that any manufacturer of appliances or equipment in the class concerned desiring voluntarily to use the Label and Energy Conservation Mark with such appliances or equipment must...

Electric toothbrushes induce electric current in fixed dental appliances by creating magnetic fields.

PubMed

Kameda, Takashi; Ohkuma, Kazuo; Ishii, Nozomu; Sano, Natsuki; Ogura, Hideo; Terada, Kazuto

2012-01-01

Magnetic fields can represent a health problem, especially low frequency electromagnetic fields sometimes induced by electric current in metallic objects worn or used in or on the body (as opposed to high frequency electromagnetic fields that produce heat). Electric toothbrushes are widely used because of their convenience, but the electric motors that power them may produce electromagnetic waves. In this study, we showed that electric toothbrushes generate low frequency (1-2000 Hz) magnetic fields and induce electric current in dental appliances (e. g. orthodontic and prosthetic appliances and dental implants). Current induced by electric toothbrushes might be dependent on the quantity and types of metals used, and the shape of the appliances. Furthermore, these induced currents in dental appliances could impact upon human oral health, producing pain and discomfort.

Lingual vs. labial fixed orthodontic appliances: systematic review and meta-analysis of treatment effects.

PubMed

Papageorgiou, Spyridon N; Gölz, Lina; Jäger, Andreas; Eliades, Theodore; Bourauel, Christoph

2016-04-01

The aim of this systematic review was to compare the therapeutic and adverse effects of lingual and labial orthodontic fixed appliances from clinical trials on human patients in an evidence-based manner. Randomized and prospective non-randomized clinical trials comparing lingual and labial appliances were included. Risk of bias within and across studies was assessed using the Cochrane tool and the Grading of Recommendations Assessment, Development and Evaluation (GRADE) approach. Random-effects meta-analyses were conducted, followed by subgroup and sensitivity analyses. Six electronic databases were searched from inception to July 2015, without limitations. A total of 13 papers pertaining to 11 clinical trials were included with a total of 407 (34% male/66% female) patients. Compared with labial appliances, lingual appliances were associated with increased overall oral discomfort, increased speech impediment (measured using auditory analysis), worse speech performance assessed by laypersons, increased eating difficulty, and decreased intermolar width. On the other hand, lingual appliances were associated with increased intercanine width and significantly decreased anchorage loss of the maxillary first molar during space closure. Based on existing trials, there is insufficient evidence to make robust recommendations for lingual fixed orthodontic appliances regarding their therapeutic or adverse effects, as the quality of evidence was low. © 2016 Eur J Oral Sci.

Effects of Brazilian Propolis on Dental Plaque and Gingiva in Patients with Oral Cleft Malformation Treated with Multibracket and Removable Appliances: A Comparative Study.

PubMed

Machorowska-Pieniążek, Agnieszka; Skucha-Nowak, Małgorzata; Mertas, Anna; Tanasiewicz, Marta; Niedzielska, Iwona; Morawiec, Tadeusz; Baron, Stefan

2016-01-01

Orthodontic appliances modify the local environment of the oral cavity, increase the accumulation of dental plaque, and affect the condition of the gingiva. The aim of this study is assessment of Brazilian propolis toothpaste's effect on plaque index (PLI) and gingival index (GI) in patients with CL/CLP treated using orthodontic appliances in the 35-day study period. The study population included 96 patients of an Orthodontic Outpatient Clinic, ACSiMS in Bytom. All the patients participated in the active phase of orthodontic treatment using buccal multibracket appliances or removable appliances. During the first examination, each patient was randomly qualified to the propolis group or control group. A statistically significant decrease in GI and PLI in the entire propolis group (P < 0.01) was shown during repeated examination. Insignificant change in GI was in the entire control group during the repeated examination compared to the baseline. Similar result was obtained in patients treated with multibracket and removable appliances. The orthodontic appliance type did not affect the final dental plaque amount and gingival condition in patients using the propolis toothpaste. These results may be clinically useful to improve prevention and control oral infectious diseases during orthodontic treatment patients with oral cleft.

[Clinical evaluation of preadjusted appliance based on Chinese normal occlusion].

PubMed

Chen, Lin; Gao, Xue-Mei; Zeng, Xiang-Long

2008-02-01

To evaluate the effect of the preadjusted appliance (Z1 appliance) based on Chinese normal occlusion. Thirty non-extraction patients were treated with Z1 appliance. No wire bending was made during treatment. The results of these 30 cases had been evaluated by five senior orthodontists. Models were analysed quantitatively to testify and evaluate the efficiency of the appliance. The average score for post-treatment models was 91.2 (total score was 100). The model measurements indicated that average projective distance on occlusal plane between proximal contact points of adjacent teeth was less than 0.3 mm, which demonstrated good alignment. The prominence of crowns was almost coincident with the data of Chinese normal occlusion. For the average tip of most teeth, there was no statistical difference between the study group and the normal control group. The crown torque variation tendency from anterior to posterior was similar to that in the subjects with normal occlusion. However, the cases treated with Z1 appliance achieved more negative torque in the lower posterior segment. The result of the non-extraction patients treated with Z1 appliance was quite satisfied. Wire bending could be reduced during treatment. It was necessary to adjust the crown torque values for lower posterior teeth.