Comparison of an objective method of measuring bulbar redness to the use of traditional grading scales.

PubMed

Sorbara, Luigina; Simpson, Trefford; Duench, Stephanie; Schulze, Marc; Fonn, Desmond

2007-03-01

The primary objective was to compare measures of bulbar redness objectively using a photometric method with standard grading methods. Measures of redness were made on 24 participants wearing a silicone hydrogel contact lens in one eye for overnight wear. This report compares hyperaemia after 1 week of daily wear (baseline) with redness measured after 6 months of overnight wear. A new method of objectively measuring bulbar conjunctival redness was performed using the Spectrascan650 Photometer by Photo Research under fixed illumination. Photometric measures in CIEu(*) chromaticity values involve the measurement of chromaticity, a physical analogue of redness, greenness and blueness in the image. This method was validated in Part 1 of the study using repeated measurements on the photographic CCLRU scale. In Part 2 of the study, the photographic grading scale (CCLRU) from 0 (none) to 100 (extreme) was used to make the comparison. Part 1 indicated that the photometer provides a repeatable and reliable measure of bulbar redness (CCC=0.989). A moderately strong and significant correlation was found between the CIEu(*) chromaticity values and the analogue data (R=0.795, p=0.000) at each measurement session (from baseline to 1 day, 1 week, and 1, 3 and 6 months of overnight wear). This new standardized and objective method of measuring bulbar redness has great potential to replace subjective grading scales, especially with multi-centre studies, where variability between investigators occurs. This method may also detect smaller changes between visits or between eyes.

A Primer on Vibrational Ball Bearing Feature Generation for Prognostics and Diagnostics Algorithms

DTIC Science & Technology

2015-03-01

Atlas -Marks (Cone-Shaped Kernel) ........................................................36 8.7.7 Hilbert-Huang Transform...bearing surface and eventually progress to the surface where the material will separate. Also known as pitting, spalling, or flaking. • Wear ...normal degradation caused by dirt and foreign particles causing abrasion of the contact surfaces over time resulting in alterations in the raceway and

[Evaluation of eye patching after cataract surgery in topical anesthesia].

PubMed

Mayer, S; Wirbelauer, C; Häberle, H; Altmeyer, M; Pham, D T

2005-01-01

Although postoperative eye patching is a common practice its background is not well known. Therefore the necessity of eye patching after cataract surgery in topical anesthesia from the medical point of view and the patients' subjective opinion was studied. In this prospective and randomized study 133 patients received after cataract surgery either no covering of the eye (group1), a transparent eye shield for four hours (group 2), an eye pad for four hours (group 3) or an eye pad until the next morning (group 4). Clinical findings were noted and local symptoms, such as pain, foreign body sensation, tearing and photophobia were documented on a visual analogue scale (0 - 10). Furthermore, a questionnaire concerning the subjective opinion was handed out to the patient. The clinical findings revealed no significant differences between the groups. The mean values for local pain were 0.94 +/- 1.56, for the foreign body sensation 1.41 +/- 2.02, for tearing 0.99 +/- 1.8 and for photophobia 1.05 +/- 1.99. Comparing the groups there was significantly more pain and foreign body sensation reported by the patients in group 3, who received eye patching for 4 hours. 91 % of the unpatched patients had no discomfort, whereas 53 % of the patients wearing an eye pad until the next morning considered it as unnecessary. After cataract surgery in topical anesthesia only mild symptoms were noted. There were no significant differences between the groups in the objective clinical findings and the subjective feeling. These results indicate that after cataract surgery eye patching could be unnecessary.

Tooth wear and wear investigations in dentistry.

PubMed

Lee, A; He, L H; Lyons, K; Swain, M V

2012-03-01

Tooth wear has been recognised as a major problem in dentistry. Epidemiological studies have reported an increasing prevalence of tooth wear and general dental practitioners see a greater number of patients seeking treatment with worn dentition. Although the dental literature contains numerous publications related to management and rehabilitation of tooth wear of varying aetiologies, our understanding of the aetiology and pathogenesis of tooth wear is still limited. The wear behaviour of dental biomaterials has also been extensively researched to improve our understanding of the underlying mechanisms and for the development of restorative materials with good wear resistance. The complex nature of tooth wear indicates challenges for conducting in vitro and in vivo wear investigations and a clear correlation between in vitro and in vivo data has not been established. The objective was to critically review the peer reviewed English-language literature pertaining to prevalence and aetiology of tooth wear and wear investigations in dentistry identified through a Medline search engine combined with hand-searching of the relevant literature, covering the period between 1960 and 2011. © 2011 Blackwell Publishing Ltd.

Wear Distribution Detection of Knee Joint Prostheses by Means of 3D Optical Scanners

PubMed Central

Affatato, Saverio; Valigi, Maria Cristina; Logozzo, Silvia

2017-01-01

The objective of this study was to examine total knee polyethylene inserts from in vitro simulation to evaluate and display—using a 3D optical scanner—wear patterns and wear rates of inserts exposed to wear by means of simulators. Various sets of tibial inserts have been reconstructed by using optical scanners. With this in mind, the wear behavior of fixed and mobile bearing polyethylene knee configurations was investigated using a knee wear joint simulator. After the completion of the wear test, the polyethylene menisci were analyzed by an innovative 3D optical scanners in order to evaluate the 3D wear distribution on the prosthesis surface. This study implemented a new procedure for evaluating polyethylene bearings of joint prostheses obtained after in vitro wear tests and the proposed new approach allowed quantification of the contact zone on the geometry of total knee prostheses. The results of the present study showed that mobile TKPs (total knee prosthesis) have lower wear resistance with respect to fixed TKPs. PMID:28772725

Foreign bodies.

PubMed

Smith, Milton T; Wong, Roy K H

2007-04-01

The spectrum of gastrointestinal (GI) foreign bodies includes food bolus impaction in the esophagus, nonfood objects that are swallowed, and various objects that may be inserted into the rectum. The risk depends upon the type of object and its location. Fortunately, 80% to 90% of ingested foreign bodies will pass without intervention. Objects with sharp edges or pointed tips have the highest risk of complications, up to 35%. All objects impacted in the esophagus require urgent or emergent treatment. Rectal foreign bodies are usually removable transanally, although general anesthesia and operative intervention sometimes are required.

Mechanical and wear properties of aluminum coating prepared by cold spraying

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yusof, Siti Nurul Akmal, E-mail: em-leo277@yahoo.com; Manap, Abreeza, E-mail: Abreeza@uniten.edu.my; Afandi, Nurfanizan Mohd

In this study, aluminum (Al) powders were deposited onto Al substrates using cold spray to form a coating. The main objective is to investigate and compare the microstructure, mechanical and wear properties of Al coating to that of the Al substrate. The microstructure of the coating and substrate were observed using Scanning Electron Microscope (SEM). Hardness was evaluated using the Vickers Hardness test and wear properties were investigated using a pin-on-disk wear test machine. The elemental composition of the coating and substrate was determined using Energy-dispersive X-ray spectroscopy (EDX). Results showed that the friction coefficient and specific wear rate decreasedmore » while wear rate increased linearly with increasing load. It was found that the coating exhibit slightly better mechanical and wear properties compared to the substrate.« less

Foreign Object in the Eye: First Aid

MedlinePlus

... eye: First aid Foreign object in the eye: First aid By Mayo Clinic Staff If you get a foreign object in your eye Wash your hands ... et al., eds. American Medical Association Handbook of First Aid and Emergency Care. New York, N.Y.: Random ...

Performance evaluation of thin wearing courses through scaled accelerated trafficking.

DOT National Transportation Integrated Search

2014-01-01

The primary objective of this study was to evaluate the permanent deformation (rutting) and fatigue performance of : several thin asphalt concrete wearing courses using a scaled-down accelerated pavement testing device. The accelerated testing : was ...

Performance Evaluation of Thin Wearing Courses Through Scaled Accelerated Trafficking.

DOT National Transportation Integrated Search

2014-01-01

"The primary objective of this study was to evaluate the permanent deformation (rutting) and fatigue performance of : several thin asphalt concrete wearing courses using a scaled-down accelerated pavement testing device. The accelerated testing : was...

Wearing the marks of violence: Unusual trauma patterning at Coyo Oriental, Northern Chile.

PubMed

Torres-Rouff, Christina; Hubbe, Mark; Pestle, William J

2018-05-02

In this article, we present analyses of traumatic injury data from the Middle Period Coyo Oriental cemetery in northern Chile. We test a series of hypotheses about the role of sex, foreign contact, ritual access, and temporal shifts, in the patterning of cranial trauma in this cemetery. Two hundred and twenty-seven crania from Coyo Oriental were analyzed using standard bioarcheological methods to determine sex and age as well as the presence of cranial fractures. We also documented the presence of Tiwanaku goods, objects tied to warfare or hunting, camelid offerings, snuff paraphernalia, and items related to mining. We recorded 98 cranial fractures in the sample with 94.9% (93/98) on the anterior of the cranium. No significant differences are observed in the prevalence of trauma by sex, type of grave, or date. However, Coyo Oriental's trauma prevalence is two to three times higher than other Middle Period sites. The prevalence and location of these injuries suggest that conflict at Coyo Oriental, while of the same nature, was at a scale different to that seen elsewhere in the oases. We posit here that the development of social hierarchy, population growth, expansive social networks, and foreign contact that characterized the Middle Period may have resulted in a need for social control among the emergent elites of the region. © 2018 Wiley Periodicals, Inc.

Insight into Foreign Thoughtworlds for National Security Decision Makers

DTIC Science & Technology

2004-01-01

ideals our nation espouses. And bent on global hegemony : as if Americans’ main comfort in life was to await the day when “the United States will...t]he matter-of-fact acceptance of our hegemony is wearing off.”5 This trend is accelerated by the image of arrogance. Compellance, then, appears...individual integration into groups • Masculinity (versus femininity), an indicator of relative assertiveness and competitiveness • Uncertainty

Validation of accelerometer wear and nonwear time classification algorithm.

PubMed

Choi, Leena; Liu, Zhouwen; Matthews, Charles E; Buchowski, Maciej S

2011-02-01

the use of movement monitors (accelerometers) for measuring physical activity (PA) in intervention and population-based studies is becoming a standard methodology for the objective measurement of sedentary and active behaviors and for the validation of subjective PA self-reports. A vital step in PA measurement is the classification of daily time into accelerometer wear and nonwear intervals using its recordings (counts) and an accelerometer-specific algorithm. the purpose of this study was to validate and improve a commonly used algorithm for classifying accelerometer wear and nonwear time intervals using objective movement data obtained in the whole-room indirect calorimeter. we conducted a validation study of a wear or nonwear automatic algorithm using data obtained from 49 adults and 76 youth wearing accelerometers during a strictly monitored 24-h stay in a room calorimeter. The accelerometer wear and nonwear time classified by the algorithm was compared with actual wearing time. Potential improvements to the algorithm were examined using the minimum classification error as an optimization target. the recommended elements in the new algorithm are as follows: 1) zero-count threshold during a nonwear time interval, 2) 90-min time window for consecutive zero or nonzero counts, and 3) allowance of 2-min interval of nonzero counts with the upstream or downstream 30-min consecutive zero-count window for detection of artifactual movements. Compared with the true wearing status, improvements to the algorithm decreased nonwear time misclassification during the waking and the 24-h periods (all P values < 0.001). the accelerometer wear or nonwear time algorithm improvements may lead to more accurate estimation of time spent in sedentary and active behaviors.

Common symptoms of Nepalese soft contact lens wearers: A pilot study.

PubMed

Sapkota, Kishor; Martin, Raul; Franco, Sandra; Lira, Madalena

2015-01-01

To determine the common symptoms in current soft contact lens (CL) wearers and their association with other factors among Nepalese population. All the current CL wearers who started to wear soft CL in Nepal Eye Hospital between July 2007 and June 2012 were invited for the participation. Frequency of the ten most common symptoms, divided into never, occasionally, frequently and consistent were recorded. Association between degree of symptoms with other factors, e.g. age, gender, profession, cigarette smoking, ethnicity, level of education and duration and wearing modality of CL wear were analyzed. Out of 129 subjects participated in this study, 67% were female; the mean age of the subjects was 23.9±4.3 years. Ninety seven percent of them had at least one symptom occasionally or frequently or consistently. Discomfort was found in 88.4% of the total subjects. Other common symptoms were foreign body sensation in 73.6%, redness in 65.9%, reduced wearing time in 63.6% and dryness in 62.8%. Symptoms were found occasionally in the majority of subjects. Degree of symptoms was not associated with age, gender, profession, education status, ethnicity of subjects and duration or modality of lens wear (p>0.05) but was positively associated with passive cigarette smoking (p<0.001). Almost all of the Nepalese soft CL wearers had some types of symptoms at least occasionally. Discomfort was the most common symptom. Degree of symptoms was associated with the passive smoking but not with other factors like age, sex, profession and duration of lens wear. Copyright © 2014 Spanish General Council of Optometry. Published by Elsevier Espana. All rights reserved.

Effect of chewing speed on the detection of a foreign object in food.

PubMed

Paphangkorakit, J; Ladsena, V; Rukyuttithamkul, T; Khamtad, T

2016-03-01

Accidentally biting hard on a piece of hard foreign object in food is among the causes of tooth fracturing and could be associated with oral sensibility. This study has investigated the effect of chewing speed on the ability to detect a foreign object in food in human. Fourteen healthy subjects were asked to randomly chew one of 10 cooked rice balls, five of which containing a foreign object made from a tiny uncooked rice grain, until they detected the rice grain. Each subject chewed the test foods both at 50 (slow) and 100 (fast) chews min(-1). The accuracy of detection and the number of chews before detection (CBD) were recorded and compared between the two chewing speeds using paired t-tests. The results showed that almost all subjects detected the foreign object by biting. The accuracy of detection was more than 90% and not significantly different between slow and fast chewing but the mean CBD in slow chewing (11·7 ± 1·3 chews) was significantly different from that in fast chewing (20·7 ± 1·9 chews; P < 0·001). The study showed that slow chewers required less number of chews before a foreign object in food could be detected and was, presumably, more effective in detecting the object compared to fast chewers. If each chew bears equal probability of teeth encountering the foreign object, slow chewing might also reduce the chance of accidentally biting hard on the foreign object and fracturing the tooth. © 2015 John Wiley & Sons Ltd.

Optimization of turning process through the analytic flank wear modelling

NASA Astrophysics Data System (ADS)

Del Prete, A.; Franchi, R.; De Lorenzis, D.

2018-05-01

In the present work, the approach used for the optimization of the process capabilities for Oil&Gas components machining will be described. These components are machined by turning of stainless steel castings workpieces. For this purpose, a proper Design Of Experiments (DOE) plan has been designed and executed: as output of the experimentation, data about tool wear have been collected. The DOE has been designed starting from the cutting speed and feed values recommended by the tools manufacturer; the depth of cut parameter has been maintained as a constant. Wear data has been obtained by means the observation of the tool flank wear under an optical microscope: the data acquisition has been carried out at regular intervals of working times. Through a statistical data and regression analysis, analytical models of the flank wear and the tool life have been obtained. The optimization approach used is a multi-objective optimization, which minimizes the production time and the number of cutting tools used, under the constraint on a defined flank wear level. The technique used to solve the optimization problem is a Multi Objective Particle Swarm Optimization (MOPS). The optimization results, validated by the execution of a further experimental campaign, highlighted the reliability of the work and confirmed the usability of the optimized process parameters and the potential benefit for the company.

Compliance with removable orthodontic appliances.

PubMed

Shah, Nirmal

2017-12-22

Data sourcesMedline via OVID, PubMed, Cochrane Central Register of Controlled Trials, Web of Science Core Collection, LILACS and BBO databases. Unpublished clinical trials accessed using ClinicalTrials.gov, National Research Register, ProQuest Dissertation and Thesis database.Study selectionTwo authors searched studies from inception until May 2016 without language restrictions. Quantitative and qualitative studies incorporating objective data on compliance with removable appliances, barriers to appliance wear compliance, and interventions to improve compliance were included.Data extraction and synthesisQuality of research was assessed using the Cochrane Collaboration's risk of bias tool, the risk of bias in non-randomised studies of interventions (ROBINS-I), and the mixed methods appraisal tool. Statistical heterogeneity was investigated by examining a graphic display of the estimated compliance levels in conjunction with 95% confidence intervals and quantified using the I-squared statistic. A weighted estimate of objective compliance levels for different appliances in relation to stipulated wear and self-reported levels was also calculated. Risk of publication bias was assessed using funnel plots. Meta-regression was undertaken to assess the relative effects of appliance type on compliance levels.ResultsTwenty-four studies met the inclusion criteria. Of these, 11 were included in the quantitative synthesis. The mean duration of objectively measured wear was considerably lower than stipulated wear time amongst all appliances. Headgear had the greatest discrepancy (5.81 hours, 95% confidence interval, 4.98, 6.64). Self-reported wear time was consistently higher than objectively measured wear time amongst all appliances. Headgear had the greatest discrepancy (5.02 hours, 95% confidence interval, 3.64, 6.40). Two studies found an increase in compliance with headgear and Hawley retainers when patients were aware of monitoring. Five studies found younger age groups to be more compliant than older groups. Three studies also found compliance to be better in the early stages of treatment. Integration between quantitative and qualitative studies was not possible.ConclusionsCompliance with removable orthodontic appliances is suboptimal. Patients wear appliances for considerably less time than stipulated and self-reported. Compliance may be increased when patients are aware of monitoring; however, further research is required to identify effective interventions and possible barriers in order to improve removable orthodontic appliance compliance.

Investigation on the Tribological Behavior and Wear Mechanism of Five Different Veneering Porcelains

PubMed Central

Min, Jie; Zhang, Qianqian; Qiu, Xiaoli; Zhu, Minhao; Yu, Haiyang; Gao, Shanshan

2015-01-01

Objectives The primary aim of this research was to investigate the wear behavior and wear mechanism of five different veneering porcelains. Methods Five kinds of veneering porcelains were selected in this research. The surface microhardness of all the samples was measured with a microhardness tester. Wear tests were performed on a ball-on-flat PLINT fretting wear machine, with lubrication of artificial saliva at 37°C. The friction coefficients were recorded by the testing system. The microstructure features, wear volume, and damage morphologies were recorded and analyzed with a confocal laser scanning microscope and a scanning electron microscope. The wear mechanism was then elucidated. Results The friction coefficients of the five veneering porcelains differ significantly. No significant correlation between hardness and wear volume was found for these veneering porcelains. Under lubrication of artificial saliva, the porcelain with higher leucite crystal content exhibited greater wear resistance. Additionally, leucite crystal size and distribution in glass matrix influenced wear behavior. The wear mechanisms for these porcelains were similar: abrasive wear dominates the early stage, whereas delamination was the main damage mode at the later stage. Furthermore, delamination was more prominent for porcelains with larger crystal sizes. Significance Wear compatibility between porcelain and natural teeth is important for dental restorative materials. Investigation on crystal content, size, and distribution in glass matrix can provide insight for the selection of dental porcelains in clinical settings. PMID:26368532

Endodontic management of a foreign body.

PubMed

Kalyan, Satish R; Sajjan, Girija

2010-07-01

The discovery of a foreign object embedded in a tooth is relatively uncommon. Some people have a habit of placing foreign objects to remove food plugs from the teeth. However, occasionally, these objects may be lodged in the teeth. These foreign objects may act as a potential source of infection and may later lead to a painful condition. A detailed case history, clinical, and radiographic examination is required to ascertain the size, position, and likely composition of the object, and also difficulty involved in its retrieval. This paper describes the successful retrieval of stapler pin located in the apical portion of root canal by simple orthograde nonsurgical technique.

Endodontic management of a foreign body

PubMed Central

Kalyan, Satish R.; Sajjan, Girija

2010-01-01

The discovery of a foreign object embedded in a tooth is relatively uncommon. Some people have a habit of placing foreign objects to remove food plugs from the teeth. However, occasionally, these objects may be lodged in the teeth. These foreign objects may act as a potential source of infection and may later lead to a painful condition. A detailed case history, clinical, and radiographic examination is required to ascertain the size, position, and likely composition of the object, and also difficulty involved in its retrieval. This paper describes the successful retrieval of stapler pin located in the apical portion of root canal by simple orthograde nonsurgical technique. PMID:22114412

Wear in ceramic on ceramic type lumbar total disc replacement: effect of radial clearance.

PubMed

Shankar, S; Kesavan, D

2015-01-01

The wear of the bearing surfaces of total disc replacement (TDR) is a key problem leads to reduction in the lifetime of the prosthesis and it mainly occurs due to the range of clearances of the articulating surface between the superior plate and core. The objective of this paper is to estimate the wear using finite element concepts considering the different radial clearances between the articulating surfaces of ceramic on ceramic type Lumbar Total Disc Replacement (LTDR). The finite element (FE) model was subjected to wear testing protocols according to loading profile of International Standards Organization (ISO) 18192 standards through 10 million cycles. The radial clearance value of 0.05 mm showed less volumetric wear when compared with other radial clearance values. Hence, low radial clearance values are suitable for LTDR to minimize the wear.

Wear rates of artificial denture teeth opposed by natural dentition.

PubMed

Douglas, W H; Delong, R; Pintado, M R; Latta, M A

1993-01-01

The wear rate of polymeric or composite-based artificial denture teeth on fixed, removable and implant prostheses is important in the maintenance of cuspal form, masticatory efficiency and occlusal stability. A servo-hydraulic based artificial mouth in which an occlusion was established between artificial denture teeth, and the palatal cusp of a human maxillary third molar was established and used to assess the wear resistance of 5 artificial denture tooth materials. Volumetric wear was determined for Dentsply Trublend SLM, Dentsply IPN, Vita Vitapan, Ivoclar Orthotyp and Ivoclar Orthosit denture teeth. Scanning electron microscopy was also done to assess the textural character of the wear facets of each denture tooth sample. The lowest volume loss was observed for Trublend SLM followed by IPN, Orthotyp, Vitapan and Orthosit. Textural assessment of the materials was consistent with the objective wear data.

Vaginal foreign bodies.

PubMed

Stricker, T; Navratil, F; Sennhauser, F H

2004-04-01

To evaluate the clinical features and outcome in girls with a vaginal foreign body. Retrospective review of medical records of 35 girls with a vaginal foreign body seen in an outpatient clinic for paediatric and adolescent gynaecology between 1980 and 2000. The ages ranged from 2.6 to 9.2 years. The most common symptom was blood-stained vaginal discharge/vaginal bleeding (49%). Duration of symptoms varied from 1 day to 2 years. Fifty-four percent of the patients recalled insertion of the foreign object, usually by the girl herself. All but three patients (91%) either recalled insertion of the foreign object and/or had vaginal bleeding or blood-stained or foul-smelling vaginal discharge, and/or visualization or palpation of the foreign body in physical examination. Symptoms resolved after removal of the foreign body followed by a single irrigation with Providon-Iod (Betadine). In the majority of patients a carefully obtained history and physical examination suggest the diagnosis of a vaginal foreign object. The leading symptoms are vaginal bleeding and blood-stained or foul smelling vaginal discharge. Removal of the foreign object followed by a single irrigation with Providon-Iod is the definitive treatment and does not require additional measures.

Quantification of the effect of cross-shear and applied nominal contact pressure on the wear of moderately cross-linked polyethylene.

PubMed

Abdelgaied, Abdellatif; Brockett, Claire L; Liu, Feng; Jennings, Louise M; Fisher, John; Jin, Zhongmin

2013-01-01

Polyethylene wear is a great concern in total joint replacement. It is now considered a major limiting factor to the long life of such prostheses. Cross-linking has been introduced to reduce the wear of ultra-high-molecular-weight polyethylene (UHMWPE). Computational models have been used extensively for wear prediction and optimization of artificial knee designs. However, in order to be independent and have general applicability and predictability, computational wear models should be based on inputs from independent experimentally determined wear parameters (wear factors or wear coefficients). The objective of this study was to investigate moderately cross-linked UHMWPE, using a multidirectional pin-on-plate wear test machine, under a wide range of applied nominal contact pressure (from 1 to 11 MPa) and under five different kinematic inputs, varying from a purely linear track to a maximum rotation of +/- 55 degrees. A computational model, based on a direct simulation of the multidirectional pin-on-plate wear tester, was developed to quantify the degree of cross-shear (CS) of the polyethylene pins articulating against the metallic plates. The moderately cross-linked UHMWPE showed wear factors less than half of that reported in the literature for, the conventional UHMWPE, under the same loading and kinematic inputs. In addition, under high applied nominal contact stress, the moderately crosslinked UHMWPE wear showed lower dependence on the degree of CS compared to that under low applied nominal contact stress. The calculated wear coefficients were found to be independent of the applied nominal contact stress, in contrast to the wear factors that were shown to be highly pressure dependent. This study provided independent wear data for inputs into computational models for moderately cross-linked polyethylene and supported the application of wear coefficient-based computational wear models.

29 CFR 1915.155 - Head protection.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT Personal Protective Equipment... wears a protective helmet when working in areas where there is a potential for injury to the head from falling objects. (2) The employer shall ensure that each affected employee wears a protective helmet...

29 CFR 1915.155 - Head protection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT Personal Protective Equipment... wears a protective helmet when working in areas where there is a potential for injury to the head from falling objects. (2) The employer shall ensure that each affected employee wears a protective helmet...

Backside wear in modern total knee designs.

PubMed

Jayabalan, Prakash; Furman, Bridgette D; Cottrell, Jocelyn M; Wright, Timothy M

2007-02-01

Although modularity affords various options to the orthopedic surgeon, these benefits come at a price. The unintended bearing surface between the back surface of the tibial insert and the metallic tray results in micromotion leading to polyethylene wear debris. The objective of this study was to examine the backside wear of tibial inserts from three modern total knee designs with very different locking mechanisms: Insall-Burstein II (IB II), Optetrak, and Advance. A random sample of 71 inserts were obtained from our institution's retrieval collection and examined to assess the extent of wear, depth of wear, and wear damage modes. Patient records were also obtained to determine patient age, body mass index, length of implantation, and reason for revision. Modes of wear damage (abrasion, burnishing, scratching, delamination, third body debris, surface deformation, and pitting) were then scored in each zone from 0 to 3 (0 = 0%, 1 = 0-10%, 2 = 10-50%, and 3 = >50%). The depth of wear was subjectively identified as removal of manufacturing identification markings stamped onto the inferior surface of the polyethylene. Both Advance and IB II polyethylene inserts showed significantly higher scores for backside wear than the Optetrak inserts. All IB II and Advance implants showed evidence of backside wear, whereas 17% (5 out of 30) of the retrieved Optetrak implants had no observable wear. There were no significant differences when comparing the depth of wear score between designs. The locking mechanism greatly affects the propensity for wear and should be considered when choosing a knee implant system.

Multi-objective optimization of swash plate forging process parameters for the die wear/service life improvement

NASA Astrophysics Data System (ADS)

Hu, X. F.; Wang, L. G.; Wu, H.; Liu, S. S.

2017-12-01

For the forging process of the swash plate, the author designed a kind of multi-index orthogonal experiment. Based on the Archard wear model, the influences of billet temperature, die temperature, forming speed, top die hardness and friction coefficient on forming load and die wear were numerically simulated by DEFORM software. Through the analysis of experimental results, the best forging process parameters were optimized and determined, which could effectively reduce the die wear and prolong the die service life. It is significant to increase the practical production of enterprise, especially to reduce the production cost and to promote enterprise profit.

Development of a pilot-scale kinetic extruder feeder system and test program. Phase II. Verification testing. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-01-12

This report describes the work done under Phase II, the verification testing of the Kinetic Extruder. The main objective of the test program was to determine failure modes and wear rates. Only minor auxiliary equipment malfunctions were encountered. Wear rates indicate useful life expectancy of from 1 to 5 years for wear-exposed components. Recommendations are made for adapting the equipment for pilot plant and commercial applications. 3 references, 20 figures, 12 tables.

Classification of accelerometer wear and non-wear events in seconds for monitoring free-living physical activity

PubMed Central

Zhou, Shang-Ming; Hill, Rebecca A; Morgan, Kelly; Stratton, Gareth; Gravenor, Mike B; Bijlsma, Gunnar; Brophy, Sinead

2015-01-01

Objective To classify wear and non-wear time of accelerometer data for accurately quantifying physical activity in public health or population level research. Design A bi-moving-window-based approach was used to combine acceleration and skin temperature data to identify wear and non-wear time events in triaxial accelerometer data that monitor physical activity. Setting Local residents in Swansea, Wales, UK. Participants 50 participants aged under 16 years (n=23) and over 17 years (n=27) were recruited in two phases: phase 1: design of the wear/non-wear algorithm (n=20) and phase 2: validation of the algorithm (n=30). Methods Participants wore a triaxial accelerometer (GeneActiv) against the skin surface on the wrist (adults) or ankle (children). Participants kept a diary to record the timings of wear and non-wear and were asked to ensure that events of wear/non-wear last for a minimum of 15 min. Results The overall sensitivity of the proposed method was 0.94 (95% CI 0.90 to 0.98) and specificity 0.91 (95% CI 0.88 to 0.94). It performed equally well for children compared with adults, and females compared with males. Using surface skin temperature data in combination with acceleration data significantly improved the classification of wear/non-wear time when compared with methods that used acceleration data only (p<0.01). Conclusions Using either accelerometer seismic information or temperature information alone is prone to considerable error. Combining both sources of data can give accurate estimates of non-wear periods thus giving better classification of sedentary behaviour. This method can be used in population studies of physical activity in free-living environments. PMID:25968000

Unusual foreign bodies in the orofacial region.

PubMed

Passi, Sidhi; Sharma, Neeraj

2012-01-01

Foreign bodies may be deposited in the oral cavity either by traumatic injury or iatrogenically. Among the commonly encountered iatrogenic foreign bodies are restorative materials like amalgam, obturation materials, broken instruments, needles, and so forth. The discovery of foreign bodies in the teeth is a special situation, which is often diagnosed accidentally. Detailed case history, clinical and radiographic examinations are necessary to come to a conclusion about the nature, size, location of the foreign body, and the difficulty involved in its retrieval. It is more common to find this situation in children as it is a well-known fact that children often tend to have the habit of placing foreign objects in the mouth. Sometimes the foreign objects get stuck in the root canals of the teeth, which the children do not reveal to their parents due to fear. These foreign objects may act as a potential source of infection and may later lead to a painful condition. This paper discusses the presence of unusual foreign bodies-a tip of the metallic compass, stapler pin, copper strip, and a broken sewing needle impregnated in the gingiva and their management.

Unusual Foreign Bodies in the Orofacial Region

PubMed Central

Passi, Sidhi; Sharma, Neeraj

2012-01-01

Foreign bodies may be deposited in the oral cavity either by traumatic injury or iatrogenically. Among the commonly encountered iatrogenic foreign bodies are restorative materials like amalgam, obturation materials, broken instruments, needles, and so forth. The discovery of foreign bodies in the teeth is a special situation, which is often diagnosed accidentally. Detailed case history, clinical and radiographic examinations are necessary to come to a conclusion about the nature, size, location of the foreign body, and the difficulty involved in its retrieval. It is more common to find this situation in children as it is a well-known fact that children often tend to have the habit of placing foreign objects in the mouth. Sometimes the foreign objects get stuck in the root canals of the teeth, which the children do not reveal to their parents due to fear. These foreign objects may act as a potential source of infection and may later lead to a painful condition. This paper discusses the presence of unusual foreign bodies—a tip of the metallic compass, stapler pin, copper strip, and a broken sewing needle impregnated in the gingiva and their management. PMID:22830058

Permethrin exposure from fabric-treated military uniforms under different wear-time scenarios.

PubMed

Proctor, Susan P; Maule, Alexis L; Heaton, Kristin J; Adam, Gina E

2014-11-01

The objective of the project was to ascertain whether urinary biomarkers of permethrin exposure are detected after wearing post-tailored, fabric-treated military uniforms under two different wear-time exposure scenarios. Study A occurred over 3.5 days and involved six participants wearing treated uniforms continuously for 30-32 h. Urine collection occurred at scheduled time points before, during, and after wearing the uniform. Study B, conducted over 19 days, included 11 participants wearing treated uniforms for 3 consecutive days, 8 h each day (with urine collection before, during, and after wear). Urinary biomarkers of permethrin (3-phenoxybenzoic acid (3PBA), cis- 2,2-(dichlorovinyl)-2,2-dimethylcyclopropane-1-carboxylic acid (cDCCA), trans- 2,2-(dichlorovinyl)-2,2-dimethylcyclopropane-1-carboxylic acid (tDCCA)) were detected during and after wear. Biomarker detection generally occurred over the 10- to 12-h period after putting on the uniform and subsided 24 h following uniform removal (in both Study A and B scenarios). Those wearing permethrin-treated uniforms under the longer wear-time scenario (Study A) excreted significantly higher cumulative mean levels compared with those in Study B (3.29 times higher for 3PBA and 2.23 times higher for the sum of c/tDCCA (P≤0.001)). Findings suggest that wearing permethrin-treated clothing does increase absorbed, internal dose levels of permethrin above population levels and is significantly related to wear-time duration.

Association Between Adherence to Glasses Wearing During Amblyopia Treatment and Improvement in Visual Acuity.

PubMed

Maconachie, Gail D E; Farooq, Shegufta; Bush, Glen; Kempton, Julie; Proudlock, Frank A; Gottlob, Irene

2016-12-01

Occlusion dose monitors have helped establish that better adherence to occlusion is associated with improved visual outcomes in patients undergoing amblyopia treatment. However, the role of adherence to glasses wearing is unknown. To establish the feasibility and reliability of objectively monitoring adherence to glasses wearing using age-based norms, establish the association between adherence to glasses wearing and improvement in visual acuity (VA) after optical treatment and occlusion therapy, and analyze the effect of age, sex, refractive errors, type of amblyopia, and adherence to glasses wearing on improvement in VA. A prospective, observational, nonmasked, cohort study was conducted between June 8, 2008, and June 30, 2013, among patients at a pediatric ophthalmology clinic of a tertiary care hospital who were newly diagnosed with anisometropic and/or strabismic amblyopia and had not undergone previous treatment. The study consisted of a glasses phase (18 weeks) and a patching phase (glasses and occlusion for 10 hours per day for 12 weeks). Reliability of the glasses monitors was assessed by comparing diary entries and monitor recordings in adults. Objective monitoring of glasses wearing and occlusion. Adherence to glasses wearing (hours per day) and effect on VA. Among 20 children with anisometropia (mean [SD] age, 6.20 [2.16] years; 11 boys and 9 girls) and 20 with strabismic or mixed amblyopia (mean [SD] age, 4.90 [1.36] years; 10 boys and 10 girls), adherence to glasses wearing was successfully monitored in all but 1 patient. Agreement between diaries and monitored times wearing glasses in adults was high (intraclass correlation coefficient, 1.00; 95% CI, 0.999-1.00). Median (SD) adherence to glasses wearing was 70% (25.3%). A moderate correlation was observed between adherence to glasses wearing and percentage improvement in VA during the glasses phase (r = 0.462; P = .003). Multiple regression revealed that age (β = -0.535; P = .001), type of amblyopia (β = -0.347; P = .02), and adherence to glasses wearing (β = 0.287; P = .04) were independently associated with improvement in VA after the glasses phase and explained 42% of the variability (F3,35 = 8.457; P < .001). A strong correlation between glasses wearing and occlusion adherence was observed (r = 0.719; P < .001). The results suggest that adherence to glasses wearing is less than optimal and highly variable but is important in achieving good VA. This study emphasizes the importance of encouraging children to not only have good adherence to occlusion therapy but also to glasses wearing.

Debris Hazards At Civil Airports

DOT National Transportation Integrated Search

1996-07-05

This advisory circular (AC) discusses problems of debris at airports, gives : information on foreign objects, and tells how to eliminate such objects from operational areas. It also addresses the acquisition of power sweepers : for foreign object dam...

Experimental wear behavioral studies of as-cast and 5 hr homogenized Al25Mg2Si2Cu4Ni alloy at constant load based on taguchi method

NASA Astrophysics Data System (ADS)

Harlapur, M. D.; Mallapur, D. G.; Udupa, K. Rajendra

2018-04-01

In the present study, an experimental study of the volumetric wear behaviour of Aluminium (Al-25Mg2Si2Cu4Ni) alloy in as cast and 5Hr homogenized with T6 heat treatment is carried out at constant load. The Pin on disc apparatus was used to carry out the sliding wear test. Taguchi method based on L-16 orthogonal array was employed to evaluate the data on the wear behavior. Signal-to-noise ratio among the objective of smaller the better and mean of means results were used. General regression model is obtained by correlation. Lastly confirmation test was completed to compose a comparison between the experimental results foreseen from the mention correlation. The mathematical model reveals the load has maximum contribution on the wear rate compared to speed. Scanning Electron Microscope was used to analyze the worn-out wear surfaces. Wear results show that 5Hr homogenized Al-25Mg2Si2Cu4Ni alloy samples with T6 treated had better volumetric wear resistance as compared to as cast samples.

Digital imaging of patterns of dental wear to diagnose bruxism in children.

PubMed

Restrepo, C; Peláez, A; Alvarez, E; Paucar, C; Abad, P

2006-07-01

The aim of this study was to evaluate and compare the area, perimeter, and form (D factor and fractal dimension) of the dental wear among bruxist and nonbruxist children with mixed dentition in order to determine if the dental wear may be used as criteria to diagnose bruxism. The children were 8 to 11 years old and were classified as bruxist or nonbruxist, according to anxiety level and temporomandibular disorders. Dental casts of the upper arch were obtained for the bruxist (n = 24) and the control (n = 29) group. The dental wear was measured in digital format and processed automatically. The complete and pathological dental wear was compared between the two groups, using the Student's t-test and Mann-Whitney test. Statistically significant differences were observed between the two groups, with a higher area, perimeter, and more irregular form of the pathological dental wear among the bruxist group. Regarding complete dental wear, differences were only significant for the D factor (an un-dimensional quantitative parameter which produces a relation between the area and the perimeter of an object). Digital imaging of dental wear may be used as criteria to diagnose bruxism in children with mixed dentition after making an analysis of the area, perimeter, and irregularity of the form of pathological dental wear.

Updates in pediatric gastrointestinal foreign bodies.

PubMed

Wright, Christian C; Closson, Forrest T

2013-10-01

Although most ingested foreign bodies in children pass spontaneously, certain foreign bodies can be harmful and they require special attention and emergent medical intervention to prevent significant morbidity and mortality. This article presents an overview of the epidemiology, diagnosis, management, and complications of foreign body ingestions in children. Particular attention is paid to coins, sharp objects, long objects, food bolus, caustic liquids, batteries, and magnets. Copyright © 2013 Elsevier Inc. All rights reserved.

Friction and fretting wear characteristics of different diamond-like carbon coatings against alumina in water-lubricated fretting conditions.

PubMed

Watabe, Tsukasa; Amanov, Auezhan; Tsuboi, Ryo; Sasaki, Shinya

2013-12-01

Diamond-like carbon (DLC) coatings typically show low friction and high wear resistance. In this study, the friction and fretting wear characteristics of PVD, CVD and CVD-Si DLC coatings were investigated against an alumina (Al2O3) ball under water-lubricated fretting conditions. The objective of this study is to investigate and compare the friction and fretting wear characteristics of those DLC coatings at various fretting frequencies. The test results showed that the PVD DLC coating led to a lower friction coefficient and a higher resistance to fretting wear compared to those of the CVD and CVD-Si DLC coatings. However, the CVD DLC coating showed that the fretting wear resistance decreases with increasing frequency, while no significant difference in fretting wear resistances of the PVD and CVD-Si DLC coatings was observed. Quantitative surface analyses of the specimens were performed using an energy dispersive spectroscopy (EDS), a laser scanning microscope (LSM), a scanning electron microscope (SEM), an atomic force microscope (AFM) and the Raman spectroscopy.

Effect of spherical Au nanoparticles on nanofriction and wear reduction in dry and liquid environments

PubMed Central

Maharaj, Dave

2012-01-01

Summary Nano-object additives are used in tribological applications as well as in various applications in liquids requiring controlled manipulation and targeting. On the macroscale, nanoparticles in solids and liquids have been shown to reduce friction and wear. On the nanoscale, atomic force microscopy (AFM) studies have been performed in single- and multiple-nanoparticle contact, in dry environments, to characterize friction forces and wear. However, limited studies in submerged liquid environments have been performed and further studies are needed. In this paper, spherical Au nanoparticles were studied for their effect on friction and wear under dry conditions and submerged in water. In single-nanoparticle contact, individual nanoparticles, deposited on silicon, were manipulated with a sharp tip and the friction force was determined. Multiple-nanoparticle contact sliding experiments were performed on nanoparticle-coated silicon with a glass sphere. Wear tests were performed on the nanoscale with AFM as well as on the macroscale by using a ball-on-flat tribometer to relate friction and wear reduction on the nanoscale and macroscale. Results indicate that the addition of Au nanoparticles reduces friction and wear. PMID:23213639

Effect of soot on oil properties and wear of engine components

NASA Astrophysics Data System (ADS)

Green, D. A.; Lewis, R.

2007-09-01

The objective of the work outlined in this paper was to increase the understanding of the wear mechanisms that occur within a soot contaminated contact zone, to help in future development of a predictive wear model to assist in the automotive engine valve train design process. The paper builds on previous work by the author, through testing of different lubricants and increased levels of soot contamination. Wear testing has been carried out using specimens operating under realistic engine conditions, using a reciprocating test-rig specifically designed for this application, where a steel disc is held in a heated bath of oil and a steel ball is attached to a reciprocating arm (replicating a sliding elephant's foot valve train contact). Detailed analysis of the test specimens has been performed using scanning electron microscopy to identify wear features relating to the proposed wear mechanisms. Analysis of worn engine components from durability engine tests has also been carried out for a comparison between specimen tests and engine testing. To assist the understanding of the wear test results obtained, the physical properties of contaminated lubricants were investigated, through viscosity, traction and friction measurements. The results have revealed how varying lubrication conditions change the wear rate of engine components and determine the wear mechanism that dominates in specific situations. Testing has also shown the positive effects of advanced engine lubricants to reduce the amount of wear produced with soot present.

22 CFR 9.2 - Objective.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Objective. 9.2 Section 9.2 Foreign Relations DEPARTMENT OF STATE GENERAL SECURITY INFORMATION REGULATIONS § 9.2 Objective. The objective of the Department's classification program is to ensure that national security information is protected from...

22 CFR 9.2 - Objective.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Objective. 9.2 Section 9.2 Foreign Relations DEPARTMENT OF STATE GENERAL SECURITY INFORMATION REGULATIONS § 9.2 Objective. The objective of the Department's classification program is to ensure that national security information is protected from...

15 CFR 930.63 - State agency objection to a consistency certification.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false State agency objection to a consistency certification. 930.63 Section 930.63 Commerce and Foreign Trade Regulations Relating to Commerce and Foreign Trade (Continued) NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE...

How patient-selected colors for removable appliances are reflected in electronically tracked compliance (wear times and wear behavior).

PubMed

Schott, Timm C; Menne, Dieter

2018-07-01

A broad spectrum of colors for removable appliances, intended to optimize acceptance of treatment and patient cooperation, have been available on the dental market for years. This is the first study to analyze how patient-selected colors are reflected in wear times and wear behavior of removable appliances. The study included 117 children (55 girls and 62 boys) who were treated with active removable plate or functional appliances. All patients were offered to choose from 11 different colors, which were pooled into six groups (black, blue, green, yellow, pink, red) for analysis, or to combine any two to four colors ("multicolored" group) for their appliances. All appliances featured a built-in microsensor (TheraMon; MC Technology, Hargelsberg, Austria) for objective wear-time tracking. Differences between wear times were analyzed using pairwise t tests and Tukey correction. The longest median wear times were recorded in the blue and green groups (≈11 h/d) and the shortest ones in the red and pink groups (≈9 h/d), but they were not significantly influenced by the patient-selected colors. The median wear times involved an age-related decrease by 0.56 h/y that was statistically significant ( P = .00005). No gender-specific patterns of wear behavior were observed. Patient-selected colors for removable appliances can presumably improve acceptance of treatment, but they are not associated with statistically significant improvements in wear time or wear behavior.

The chain of cross-contamination: link-by-link.

PubMed

Schwartz, Jeanne

2002-01-01

Conscious efforts must be made to break the chain of cross-contamination--link-by-link. Pay attention to detail Avoid being careless Avoid touching objects while wearing soiled gloves Frequently wash hands (15-second hand washing) to remove pathogens--before and after gloving, and before handling food or drink Wear all PPE, and change accordingly.

Multiple Hollow Cathode Wear Testing for the Space Station Plasma Contactor

NASA Technical Reports Server (NTRS)

Soulas, George C.

1994-01-01

A wear test of four hollow cathodes was conducted to resolve issues associated with the Space Station plasma contactor. The objectives of this test were to evaluate unit-to-unit dispersions, verify the transportability of contamination control protocols developed by the project, and to evaluate cathode contamination control and activation procedures to enable simplification of the gas feed system and heater power processor. These objectives were achieved by wear testing four cathodes concurrently to 2000 hours. Test results showed maximum unit-to-unit deviations for discharge voltages and cathode tip temperatures to be +/-3 percent and +/-2 percent, respectively, of the nominal values. Cathodes utilizing contamination control procedures known to increase cathode lifetime showed no trends in their monitored parameters that would indicate a possible failure, demonstrating that contamination control procedures had been successfully transferred. Comparisons of cathodes utilizing and not utilizing a purifier or simplified activation procedure showed similar behavior during wear testing and pre- and post-test performance characterizations. This behavior indicates that use of simplified cathode systems and procedures is consistent with long cathode lifetimes.

Influence of Cryogenic Treatments on the Wear Behavior of AISI 420 Martensitic Stainless Steel

NASA Astrophysics Data System (ADS)

Prieto, G.; Tuckart, W. R.

2017-11-01

The objective of the present work is to characterize the wear behavior of a cryogenically treated low-carbon AISI 420 martensitic stainless steel, by means of ball-on-disk tribological tests. Wear tests were performed under a range of applied normal loads and in two different environments, namely a petrolatum bath and an argon atmosphere. Wear tracks were analyzed by both optical and scanning electron microscopy and Raman spectroscopy to evaluate wear volume, track geometry, surface features and the tribolayers generated after testing. This paper is an extension of the work originally reported in the VIII Iberian Conference of Tribology (Prieto and Tuckart, in: Ballest Jiménez, Rodríguez Espinosa, Serrano Saurín, Pardilla Arias, Olivares Bermúdez (eds) VIII Iberian conference of tribology, Cartagena, 2015). In this study, it has been experimentally demonstrated that cryogenically treated specimens showed a wear resistance improvement ranging from 35 to 90% compared to conventionally treated ones.

Characterization of wear debris from metal-on-metal hip implants during normal wear versus edge-loading conditions.

PubMed

Kovochich, Michael; Fung, Ernest S; Donovan, Ellen; Unice, Kenneth M; Paustenbach, Dennis J; Finley, Brent L

2018-04-01

Advantages of second-generation metal-on-metal (MoM) hip implants include low volumetric wear rates and the release of nanosized wear particles that are chemically inert and readily cleared from local tissue. In some patients, edge loading conditions occur, which result in higher volumetric wear. The objective of this study was to characterize the size, morphology, and chemistry of wear particles released from MoM hip implants during normal (40° angle) and edge-loading (65° angle with microseparation) conditions. The mean primary particle size by volume under normal wear was 35 nm (range: 9-152 nm) compared with 95 nm (range: 6-573 nm) under edge-loading conditions. Hydrodynamic diameter analysis by volume showed that particles from normal wear were in the nano- (<100 nm) to submicron (<1000 nm) size range, whereas edge-loading conditions generated particles that ranged from <100 nm up to 3000-6000 nm in size. Particles isolated from normal wear were primarily chromium (98.5%) and round to oval in shape. Edge-loading conditions generated more elongated particles (4.5%) (aspect ratio ≥ 2.5) and more CoCr alloy particles (9.3%) compared with normal wear conditions (1.3% CoCr particles). By total mass, edge-loading particles contained approximately 640-fold more cobalt than normal wear particles. Our findings suggest that high wear conditions are a potential risk factor for adverse local tissue effects in MoM patients who experience edge loading. This study is the first to characterize both the physical and chemical characteristics of MoM wear particles collected under normal and edge-loading conditions. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 986-996, 2018. © 2017 Wiley Periodicals, Inc.

An in-vitro evaluation of mechanical and esthetic properties of orthodontic sealants

PubMed Central

Premaraj, Thyagaseely Sheela; Rohani, Nima; Covey, David; Premaraj, Sundaralingam; Hua, Yi; Watanabe, Hidehiko

2014-01-01

Objective: To evaluate mechanical and esthetic Properties of two commercially available orthodontic sealants: Opal®Seal (OS) and L.E.D. Pro Seal (PS). Materials and Methods: Discs of each sealant were prepared to test the following properties: Micro hardness, wear resistance and color stability. Samples were randomly selected after the wear test for SEM imaging to analyze surface morphology. Results: OS was significantly harder than PS (P < 0.001). PS was significantly more wear resistant than OS (P < 0.05). PS showed a greater ∆E*ab (increased staining) when placed in wine or coffee showing a significant difference (P < 0.05). SEM showed particle size, shape and distribution were different for PS and OS reflecting the pattern seen on wear surfaces. Conclusion: Both orthodontic sealants are beneficial for protecting enamel. However with better wear properties PS was superior in resisting mechanical stresses. OS was more color stable. PMID:25512729

Long-term effects of the extended wear of senofilcon A silicone hydrogel contact lenses on ocular tissues.

PubMed

Guillon, Michel; Maïssa, Cécile

2010-12-01

The objective of the investigation was to show that, because of their overall properties, Acuvue® Oasys™ with Hydraclear™ Plus brand (senofilcon A) silicone hydrogel contact lenses achieve excellent ocular tissue tolerance during long-term extended wear. The investigation was a 2-year, prospective, extended wear investigation of senofilcon A silicone hydrogel contact lenses worn for up to 6 nights without removal. The 2-year results compared with the subjects' baseline ocular statuses on entering the study revealed: The quantification of the effects on the ocular tissues of 2 years of extended wear of senofilcon A, by mainly previously successful daily soft contact lens wearers, found an excellent biocompatibility. The results support the hypothesis that senofilcon A contact lenses, when worn on a 6-night/7-day extended wear regimen, maintain excellent long-term ocular tissue tolerance. Copyright © 2010 American Optometric Association. Published by Elsevier Inc. All rights reserved.

"Kicking Up Some Dust": An Experimental Investigation Relating Lunar Dust Erosive Wear to Solar Power Loss

NASA Technical Reports Server (NTRS)

Mpagazehe, Jeremiah N.; Street, Kenneth W., Jr.; Delgado, Irebert R.; Higgs, C. Fred, III

2013-01-01

The exhaust from retrograde rockets fired by spacecraft landing on the Moon can accelerate lunar dust particles to high velocities. Information obtained from NASA's Apollo 12 mission confirmed that these high-speed dust particles can erode nearby structures. This erosive wear damage can affect the performance of optical components such as solar concentrators. Solar concentrators are objects which collect sunlight over large areas and focus the light into smaller areas for purposes such as heating and energy production. In this work, laboratory-scale solar concentrators were constructed and subjected to erosive wear by the JSC-1AF lunar dust simulant. The concentrators were focused on a photovoltaic cell and the degradation in electrical power due to the erosive wear was measured. It was observed that even moderate exposure to erosive wear from lunar dust simulant resulted in a 40 percent reduction in power production from the solar concentrators.

The influence of machining condition and cutting tool wear on surface roughness of AISI 4340 steel

NASA Astrophysics Data System (ADS)

Natasha, A. R.; Ghani, J. A.; Che Haron, C. H.; Syarif, J.

2018-01-01

Sustainable machining by using cryogenic coolant as the cutting fluid has been proven to enhance some machining outputs. The main objective of the current work was to investigate the influence of machining conditions; dry and cryogenic, as well as the cutting tool wear on the machined surface roughness of AISI 4340 steel. The experimental tests were performed using chemical vapor deposition (CVD) coated carbide inserts. The value of machined surface roughness were measured at 3 cutting intervals; beginning, middle, and end of the cutting based on the readings of the tool flank wear. The results revealed that cryogenic turning had the greatest influence on surface roughness when machined at lower cutting speed and higher feed rate. Meanwhile, the cutting tool wear was also found to influence the surface roughness, either improving it or deteriorating it, based on the severity and the mechanism of the flank wear.

The production and tribology of hard facing coatings for agricultural applications

NASA Astrophysics Data System (ADS)

Roffey, Paul

Abrasive wear is a significant issue in many industries but is of particular significance in agriculture. This research is being carried out due to the demand for a hard wearing, economical coating for use in the agricultural industry.A primary objective has been to review and develop an in depth understanding of the type of wear suffered by metal shares in agricultural soils. The affect of soil properties and abrasive wear environments on the amount of wear that occurs, and the way in which material properties can be used to reduce or prevent this has also been investigated. A review of the diverse range of soil properties, such as the mineral content, moisture content, soils strengths has been carried out in order to create an appropriate wear test procedure.The coatings developed for testing were modifications to an existing powder metallurgy coating. The modifications were made by the addition of selected hard phases to the powder prior to sintering. The resulting materials were characterised in terms of sinterability, hardness and abrasive wear resistance. Prior to commencing this work little or no data existed on the wear performance of the pre-existing coating. Wear resistance has been measured using a fixed ball micro-scale abrasive wear test (also known as the ball-cratering wear test) with SiC and SiO2 abrasives and also using a modified version of the ASTM G65 abrasive wear test which allowed testing in dry and wet modes. Limited field trials were performed to determine the abrasive wear resistance in real soil. Results from wear testing have determined that the optimum modification to the coating can improve performance compared to the unmodified coating.Detailed scanning electron microscopy (SEM) has been performed on the wear scars and has revealed the resultant wear mechanisms and role that the hard phase additions play in improving the wear resistance. The influence of the hard phase addition on the microstructure has also been studied.The wear volume and corresponding wear coefficient from laboratory studies have been used to determine the optimum level of addition that can be added to produce an improved wear resistance. The results show the optimum hard phase addition to be 100mum WC/W[2]C particles at around 10wt.% with 15 mum WC at 5wt.% also providing improved wear resistance.

The effect of Tricresyl-Phosphate (TCP) as an additive on wear of Iron (Fe)

NASA Technical Reports Server (NTRS)

Ghose, Hiren M.; Ferrante, John; Honecy, Frank C.

1987-01-01

The effect of tricresyl phosphate (TCP) as an antiwear additive in lubricant trimethyol propane triheptanoate (TMPTH) was investigated. The objective was to examine step loading wear by use of surface analysis, wetting, and chemical bonding changes in the lubricant. The investigation consisted of steploading wear studies by a pin or disk tribometer, the effects on wear related to wetting by contact angle and surface tension measurements of various liquid systems, the chemical bonding changes between lubricant and TCP chromatographic analysis, and by determining the reaction between the TCP and metal surfaces through wear scar analysis by Auger emission spectroscopy (AES). The steploading curve for the base fluid alone shows rapid increase of wear rate with load. The steploading curve for the base fluid in presence of 4.25 percent by volume TCP under dry air purge has shown a great reduction of wear rate with all loads studied. It has also been found that the addition of 4.25 percent by volume TCP plus 0.33 percent by volume water to the base lubricant under N2 purge also greatly reduces the wear rate with all loads studied. AES surface analysis reveals a phosphate type wear resistant film, which greatly increases load-bearing capacity, formed on the iron disk. Preliminary chromatographic studies suggest that this film forms either because of ester oxidation or TCP degradation. Wetting studies show direct correlation between the spreading coefficient and the wear rate.

Factors related to seatbelt-wearing among rear-seat passengers in Malaysia.

PubMed

Ng, Choy Peng; Law, Teik Hua; Wong, Shaw Voon; Kulanthayan, S

2013-01-01

The benefit of wearing a rear seatbelt in reducing the risk of motor vehicle crash-related fatalities and injuries has been well documented in previous studies. Wearing a seatbelt not only reduces the risk of injury to rear-seat passengers, but also reduces the risk of injury to front-seat occupant who could be crushed by unbelted rear-seat passengers in a motor vehicle crash. Despite the benefits of wearing a rear seatbelt, its rate of use in Malaysia is generally low. The objective of this study was to identify factors that are associated with the wearing of a seatbelt among rear-seat passengers in Malaysia. Multinomial logistic regression analysis of the results of a questionnaire survey of 1651 rear-seat passengers revealed that rear-seat passengers who were younger, male, single and less educated and who had a perception of a low level of legislation enforcement, a lower risk-aversion and less driving experience (only for passengers who are also drivers) were less likely to wear a rear seatbelt. There was also a significant positive correlation between driver seatbelt and rear seatbelt-wearing behaviour. This implies that, in regards to seatbelt-wearing behaviour, drivers are more likely to adopt the same seatbelt-wearing behaviour when travelling as rear-seat passengers as they do when driving. These findings are crucial to the development of new interventions to increase the compliance rate of wearing a rear seatbelt. Copyright © 2012 Elsevier Ltd. All rights reserved.

Comparison of Wear Resistance of Hawley and Vacuum Formed Retainers: An in-vitro Study

PubMed Central

V, Moshkelgosha; M, Shomali; M, Momeni

2016-01-01

Statement of Problem: As a physical property, wear resistance of the materials used in the fabrication of orthodontic retainers play a significant role in the stability and long term use of the appliances. Objectives: To evaluate the wear resistance of two commonly used materials for orthodontic retainers: Acropars OP, i.e. a polymethyl methacrylate based material, and 3A-GS060, i.e. a polyethylene based material. Materials and Methods: For each material, 30 orthodontic retainers were made according to the manufacturers’ instructions and a 30×30×2 mm block was cut out from the mid- palatal area of each retainer. Each specimen underwent 1000 cycles of wear stimulation in a pin on disc machine. The depth of wear of each specimen was measured using a Nano Wizard II atomic force microscope in 3 random points of each specimen’s wear trough. The average of these three measurements was calculated and considered as mean value wear depth of each specimen (µm). Results: The mean wear depth was 6.10µm and 2.15µm for 3A-GS060 and Acropars OP groups respectively. Independent t-test showed a significant difference between the two groups (p < 0.001). The results show Polymethyl methacrylate base (Acropars) is more wear resistance than the polyethylene based material (3A-GS060). Conclusions: As the higher wear resistance of the fabrication material can improve the retainers’ survival time and its cost-effectiveness, VFRs should be avoided in situations that the appliance needs high wear resistance such as bite blocks opposing occlusal forces. PMID:28959750

Tool wear mechanisms in turning titanium-aluminum-vanadium using tungsten carbide and polycrystalline diamond inserts

NASA Astrophysics Data System (ADS)

Schrock, David James

The objective of this work is to identify some of the tool wear mechanisms at the material level for the machining of titanium and to provide some understanding of these mechanisms for use in physics based tool wear models. Turning experiments were conducted at cutting speeds of 61m/min, 91m/min, and 122m/min on Ti-6Al-4V, an alloy of titanium, using two different grades of tungsten carbide cutting inserts and one grade of polycrystalline diamond inserts. Three-dimensional wear data and two-dimensional wear profiles of the rake face were generated using Confocal Laser Scanning Microscopy to quantify the tool wear mechanisms. Additionally, the microstructure of the deformed work material (chip) and un-deformed parent material (work piece) were studied using Orientation Imaging Microscopy (OIM). Observations from tool wear studies on the PCD inserts revealed the presence of two fundamentally different wear mechanisms operating at the different cutting speeds. Microstructural analyses of the chip and the work material showed phase dependent tool wear mechanisms for machining titanium. There is a high likelihood of phase change occurring in the work material during machining, with a transformation from the alpha phase to the beta phase. The observed dramatic increase in wear is attributed to a combination of increased diffusivity in the beta phase of the titanium alloy in conjunction with a higher degree of recrystallization of the prior beta phase upon cooling. Results of other observations such as the influence of carbide grain size on tool wear are also discussed.

Tooth wear: a cross-sectional investigation of the prevalence and risk factors in Beijing, China

PubMed Central

Sun, Kan; Wang, Wenhui; Wang, Xiaozhe; Shi, Xiangru; Si, Yan; Zheng, Shuguo

2017-01-01

Objectives: The aim of this study was to evaluate the epidemiology of tooth wear in Beijing and to establish appropriate preventive measures. Materials and Methods: This cross-sectional analysis involved a questionnaire survey conducted for 1,812 individuals aged 12–74 years in Beijing. Subjects were local residents living in the region for >6 months before the survey. Subjects were evaluated using clinical examinations with the basic erosive wear examination index and a self-administered questionnaire. Statistical analyses were performed using SPSS software. Results: The prevalence of maxillary tooth wear was 84.9% for the molars, 68.9% for the premolars, 74.1% for the canines and 97% for the incisors. In the mandible, the corresponding prevalence rates were 85.2%, 59.3%, 78.6% and 97.4%, respectively. The occlusal, incisal and cervical surfaces showed more frequent wear compared with the other surfaces. Age, acidic beverages, xerostomia and brushing habits were identified as risk factors for tooth wear (P<0.05). Conclusions: Tooth wear is common in Beijing. Specific preventive measures should be recommended for individuals reporting excessive consumption of fruits and/or acidic beverages, and those with xerostomia. In particular, incisor wear should be carefully monitored in individuals of all age groups. PMID:29607073

Wear behavior of AA 5083/SiC nano-particle metal matrix composite: Statistical analysis

NASA Astrophysics Data System (ADS)

Hussain Idrisi, Amir; Ismail Mourad, Abdel-Hamid; Thekkuden, Dinu Thomas; Christy, John Victor

2018-03-01

This paper reports study on statistical analysis of the wear characteristics of AA5083/SiC nanocomposite. The aluminum matrix composites with different wt % (0%, 1% and 2%) of SiC nanoparticles were fabricated by using stir casting route. The developed composites were used in the manufacturing of spur gears on which the study was conducted. A specially designed test rig was used in testing the wear performance of the gears. The wear was investigated under different conditions of applied load (10N, 20N, and 30N) and operation time (30 mins, 60 mins, 90 mins, and 120mins). The analysis carried out at room temperature under constant speed of 1450 rpm. The wear parameters were optimized by using Taguchi’s method. During this statistical approach, L27 Orthogonal array was selected for the analysis of output. Furthermore, analysis of variance (ANOVA) was used to investigate the influence of applied load, operation time and SiC wt. % on wear behaviour. The wear resistance was analyzed by selecting “smaller is better” characteristics as the objective of the model. From this research, it is observed that experiment time and SiC wt % have the most significant effect on the wear performance followed by the applied load.

Comparison of grasping movements made by healthy subjects in a 3-dimensional immersive virtual versus physical environment.

PubMed

Magdalon, Eliane C; Michaelsen, Stella M; Quevedo, Antonio A; Levin, Mindy F

2011-09-01

Virtual reality (VR) technology is being used with increasing frequency as a training medium for motor rehabilitation. However, before addressing training effectiveness in virtual environments (VEs), it is necessary to identify if movements made in such environments are kinematically similar to those made in physical environments (PEs) and the effect of provision of haptic feedback on these movement patterns. These questions are important since reach-to-grasp movements may be inaccurate when visual or haptic feedback is altered or absent. Our goal was to compare kinematics of reaching and grasping movements to three objects performed in an immersive three-dimensional (3D) VE with haptic feedback (cyberglove/grasp system) viewed through a head-mounted display to those made in an equivalent physical environment (PE). We also compared movements in PE made with and without wearing the cyberglove/grasp haptic feedback system. Ten healthy subjects (8 women, 62.1±8.8years) reached and grasped objects requiring 3 different grasp types (can, diameter 65.6mm, cylindrical grasp; screwdriver, diameter 31.6mm, power grasp; pen, diameter 7.5mm, precision grasp) in PE and visually similar virtual objects in VE. Temporal and spatial arm and trunk kinematics were analyzed. Movements were slower and grip apertures were wider when wearing the glove in both the PE and the VE compared to movements made in the PE without the glove. When wearing the glove, subjects used similar reaching trajectories in both environments, preserved the coordination between reaching and grasping and scaled grip aperture to object size for the larger object (cylindrical grasp). However, in VE compared to PE, movements were slower and had longer deceleration times, elbow extension was greater when reaching to the smallest object and apertures were wider for the power and precision grip tasks. Overall, the differences in spatial and temporal kinematics of movements between environments were greater than those due only to wearing the cyberglove/grasp system. Differences in movement kinematics due to the viewing environment were likely due to a lack of prior experience with the virtual environment, an uncertainty of object location and the restricted field-of-view when wearing the head-mounted display. The results can be used to inform the design and disposition of objects within 3D VEs for the study of the control of prehension and for upper limb rehabilitation. Copyright © 2011 Elsevier B.V. All rights reserved.

Object Familiarity Facilitates Foreign Word Learning in Preschoolers

ERIC Educational Resources Information Center

Sera, Maria D.; Cole, Caitlin A.; Oromendia, Mercedes; Koenig, Melissa A.

2014-01-01

Studying how children learn words in a foreign language can shed light on how language learning changes with development. In one experiment, we examined whether three-, four-, and five-year-olds could learn and remember words for familiar and unfamiliar objects in their native English and a foreign language. All age groups could learn and remember…

A comparison between indirect and objective wear-time assessment of removable orthodontic appliances.

PubMed

Schott, Timm C; Meyer-Gutknecht, Hannes; Mayer, Nicolai; Weber, Joachim; Weimer, Katja

2017-04-01

Patients do not always adhere to the wear times prescribed for removable orthodontic appliances. We evaluated the validity and usability of indirect wear-time assessment methods by comparing wear-time estimates with microelectronically measured wear times in patients with removable orthodontic appliances. Wear times of 33 expansion plates, 34 functional appliances, and 42 retention plates of patients aged 6-20 years (12.3±2.9 years, 50.5% female) were indirectly determined by practitioners using a questionnaire assessing five parameters on a 5-point Likert scale: appliance handling, appliance appearance, bite shift, tooth movement, and appliance fit. The perceived difficulty in assessing each parameter was rated. Actual wear times were evaluated with microelectronic sensors in the appliances. Regression analyses revealed that practitioners' decisions about wear times varied depending on the type of appliance and criteria used, with only one standard criterion best predicting estimated wear time for each appliance. Different standard criteria were better predictors of measured wear time: 22.3% of wear-time variability was explained by expansion plate appearance, 31.2% by functional appliance handling, and 18.8% by retainer fitting. However, practitioners rated the difficulty of assessment in most cases as 'easy'. The study was not double blinded for technical reasons, and practitioners may have considered the evaluation criteria more carefully than in normal daily practice. Practitioners' decisions about wear times based on standard criteria strongly vary depending on the type of appliance and criteria used. © The Author 2016. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

Effect of wear on the burst strength of l-80 steel casing

NASA Astrophysics Data System (ADS)

Irawan, S.; Bharadwaj, A. M.; Temesgen, B.; Karuppanan, S.; Abdullah, M. Z. B.

2015-12-01

Casing wear has recently become one of the areas of research interest in the oil and gas industry especially in extended reach well drilling. The burst strength of a worn out casing is one of the significantly affected mechanical properties and is yet an area where less research is done The most commonly used equations to calculate the resulting burst strength after wear are Barlow, the initial yield burst, the full yield burst and the rupture burst equations. The objective of this study was to estimate casing burst strength after wear through Finite Element Analysis (FEA). It included calculation and comparison of the different theoretical bursts pressures with the simulation results along with effect of different wear shapes on L-80 casing material. The von Misses stress was used in the estimation of the burst pressure. The result obtained shows that the casing burst strength decreases as the wear percentage increases. Moreover, the burst strength value of the casing obtained from the FEA has a higher value compared to the theoretical burst strength values. Casing with crescent shaped wear give the highest burst strength value when simulated under nonlinear analysis.

Review of intentionally self-inflicted, accidental and iatrogetic foreign objects in the genitourinary tract.

PubMed

Rieder, Jocelyn; Brusky, John; Tran, Viet; Stern, Karen; Aboseif, Sherif

2010-01-01

Retrospective evaluation of a series of patients presenting with genitourinary foreign objects. From 1997 to 2007, 11 men and 2 women were treated for a variety of foreign objects in the genitourinary tract. Medical records were reviewed for presentation, diagnosis, mental status, drug dependency, treatment, and follow-up. 13 patients were seen for removal of the foreign objects or for treatment of the sequela. These objects were intentionally self-inflicted, accidentally introduced or iatrogenic in nature. Intentional objects included: safety pins, screwdriver, marbles, pen cap, pencils, straw, cocaine, stiff metal wire and part of a pizza mixer. Accidental objects included: magnets, female catheter, urinary incontinence devices and part of a Foley catheter. The iatrogenic object was a reservoir from an inflatable penile implant. Smaller noninjurious objects were retrieved cystoscopically or at the bedside; larger objects or objects associated with trauma to the urethra needed open and reconstructive operations. Generally thought to be self-inflicted for personal gratification, the source of genitourinary objects can also be accidental or iatrogenic. The most traumatic injuries are purposely self-inflicted and found in patients who remove the objects themselves. These patients are at higher risk of permanent urethral damage needing complex surgical treatment and follow-up. Copyright (c) 2010 S. Karger AG, Basel.

Behavioral Objectives, Skinnerian Rats, and Trojan Horses

ERIC Educational Resources Information Center

Grittner, Frank M.

1972-01-01

Reviews the place of behavioral objectives in the foreign language curriculum. Paper delivered as part of a debate on Behavioral Objectives: Pro and Con" held on November 26, 1971, in Chicago, Illinois, at the Annual Meeting of the American Council on the Teaching of Foreign Languages (ACTFL). (DS)

Impact wear behavior of human tooth enamel under simulated chewing conditions.

PubMed

Zheng, Jing; Zeng, Yangyang; Wen, Jian; Zheng, Liang; Zhou, Zhongrong

2016-09-01

Previous studies mostly focused on the sliding wear behavior of human teeth, and little effort has been made so far to study the impact wear of human teeth. The objective of this study was to investigate the impact wear process and mechanism of human tooth enamel and the influence of water content within enamel. In this paper, the impact wear behaviors of fresh and dried human tooth enamel against SiC ceramic have been investigated using a specially designed impact test machine. Tests lasting up to 5×10(3), 5×10(4), 2.5×10(5), 5.5×10(5), 8×10(5) and 1×10(6) cycles were conducted, respectively. Results showed that for the fresh enamel, the surface damage was dominated by plastic deformation at the early stage of impact wear. Iridescent rings appeared around the impact mark as a result of the accumulation and spread of plastic deformation. As the impact wear progressed, delamination occurred on the surface of enamel, and thus the iridescent rings gradually disappeared. Wear loss increased rapidly with the increase of impact cycles. When a wear particle layer was formed on the enamel surface, the wear rate decreased. It was found that the surface hardness of enamel increased with the impact cycles, and no cracks appeared on the cross section of wear scar. Compared with the fresh enamel, the fracture toughness of dried enamel decreased, and thus there were microcracks appearing on the cross section of wear scar. More obvious delamination occurred on the worn surface of dried enamel, and no iridescent rings were observed. The wear loss of dried enamel was higher than that of fresh enamel. In summary, the impact wear behavior of sound human tooth enamel was metal-like to some degree, and no subsurface cracking occurred. The water content within enamel could increase its fracture toughness and protect the surface from impact wear. The wear mechanism of human tooth enamel is determined by its microstructure. Copyright © 2016 Elsevier Ltd. All rights reserved.

Endodontic management of an unusual foreign body in a maxillary central incisor.

PubMed

Chand, Keerthi; Joesph, Sam; Varughese, Jolly Mary; Nair, Mali G; Prasanth, Santhosh

2013-09-01

The discovery of foreign bodies in the teeth is often diagnosed accidentally. It is commonly seen in children. These foreign objects may act as a potential source of infection and may later lead to a painful condition. Detailed case history, clinical and radiographic examinations are necessary to come to a conclusion about the nature, size, and location of the foreign body, and the difficulty involved in its retrieval. This paper discusses the types of foreign objects found in and around the teeth and reports an unusual case of a stapler pin in the root canal of a tooth, its retrieval, and associated management of the involved teeth.

Personal, social, and environmental factors associated with lifejacket wear in adults and children: A systematic literature review

PubMed Central

Demant, Daniel; Hagger, Martin S.; Hamilton, Kyra

2018-01-01

Objective Drowning claims 7% of the global burden of injury-related deaths. Lifejackets are routinely recommended as a drowning prevention strategy; however, a review of related factors regarding lifejacket wear has not previously been investigated. Methods This systematic review examined literature published from inception to December 2016 in English and German languages. The personal, social, and environmental factors associated with lifejacket wear among adults and children were investigated, a quantitative evaluation of the results undertaken, and gaps in the literature identified. Results Twenty studies, with sample sizes of studies ranging between 20 and 482,331, were identified. Fifty-five percent were cross-sectional studies. All studies were scored IV or V on the Australian National Health and Medical Research Council (NHMRC) grading system indicating mostly descriptive and cross-sectional levels of evidence. Factors associated with increased wear included age (mostly children), gender (mostly female), boat type (non-motorised), boat size (small boats), role modelling (children influenced by adult lifejacket wear), and activity (water-skiing, fishing). Factors not associated or inconsistent with lifejacket wear included education, household income, ethnicity, boating ability, confidence in lifejackets, waterway type, and weather and water conditions. Factors associated with reduced lifejacket wear included adults, males, discomfort, cost and accessibility, consumption of alcohol, and swimming ability. Three studies evaluated the impact of interventions. Conclusion This review identified factors associated with both increased and decreased lifejacket wear. Future research should address the motivational factors associated with individuals’ decisions to wear or not wear lifejackets. This, combined with further research on the evaluation of interventions designed to increase lifejacket wear, will enhance the evidence base to support future drowning prevention interventions. PMID:29718971

Extended Wearing Trial of Trifield Lens Device for “Tunnel Vision”

PubMed Central

Woods, Russell L.; Giorgi, Robert G.; Berson, Eliot L.; Peli, Eli

2009-01-01

Severe visual field constriction (tunnel vision) impairs the ability to navigate and walk safely. We evaluated Trifield glasses as a mobility rehabilitation device for tunnel vision in an extended wearing trial. Twelve patients with tunnel vision (5 to 22 degrees wide) due to retinitis pigmentosa or choroideremia participated in the 5-visit wearing trial. To expand the horizontal visual field, one spectacle lens was fitted with two apex-to-apex prisms that vertically bisected the pupil on primary gaze. This provides visual field expansion at the expense of visual confusion (two objects with the same visual direction). Patients were asked to wear these spectacles as much as possible for the duration of the wearing trial (median 8, range 6 to 60, weeks). Clinical success (continued wear, indicating perceived overall benefit), visual field expansion, perceived direction and perceived visual ability were measured. Of 12 patients, 9 chose to continue wearing the Trifield glasses at the end of the wearing trial. Of those 9 patients, at long-term follow-up (35 to 78 weeks), 3 reported still wearing the Trifield glasses. Visual field expansion (median 18, range 9 to 38, degrees) was demonstrated for all patients. No patient demonstrated adaptation to the change in visual direction produced by the Trifield glasses (prisms). For difficulty with obstacles, some differences between successful and non-successful wearers were found. Trifield glasses provided reported benefits in obstacle avoidance to 7 of the 12 patients completing the wearing trial. Crowded environments were particularly difficult for most wearers. Possible reasons for long-term discontinuation and lack of adaptation to perceived direction are discussed. PMID:20444130

Extended wearing trial of Trifield lens device for 'tunnel vision'.

PubMed

Woods, Russell L; Giorgi, Robert G; Berson, Eliot L; Peli, Eli

2010-05-01

Severe visual field constriction (tunnel vision) impairs the ability to navigate and walk safely. We evaluated Trifield glasses as a mobility rehabilitation device for tunnel vision in an extended wearing trial. Twelve patients with tunnel vision (5-22 degrees wide) due to retinitis pigmentosa or choroideremia participated in the 5-visit wearing trial. To expand the horizontal visual field, one spectacle lens was fitted with two apex-to-apex prisms that vertically bisected the pupil on primary gaze. This provides visual field expansion at the expense of visual confusion (two objects with the same visual direction). Patients were asked to wear these spectacles as much as possible for the duration of the wearing trial (median 8, range 6-60 weeks). Clinical success (continued wear, indicating perceived overall benefit), visual field expansion, perceived direction and perceived visual ability were measured. Of 12 patients, nine chose to continue wearing the Trifield glasses at the end of the wearing trial. Of those nine patients, at long-term follow-up (35-78 weeks), three reported still wearing the Trifield glasses. Visual field expansion (median 18, range 9-38 degrees) was demonstrated for all patients. No patient demonstrated adaptation to the change in visual direction produced by the Trifield glasses (prisms). For reported difficulty with obstacles, some differences between successful and non-successful wearers were found. Trifield glasses provided reported benefits in obstacle avoidance to 7 of the 12 patients completing the wearing trial. Crowded environments were particularly difficult for most wearers. Possible reasons for long-term discontinuation and lack of adaptation to perceived direction are discussed.

14 CFR 33.77 - Foreign object ingestion-ice.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Foreign object ingestion-ice. 33.77 Section... object ingestion—ice. (a)-(b) [Reserved] (c) Ingestion of ice under the conditions of paragraph (e) of... by engine test under the following ingestion conditions: (1) Ice quantity will be the maximum...

14 CFR 33.77 - Foreign object ingestion-ice.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Foreign object ingestion-ice. 33.77 Section... object ingestion—ice. (a)-(b) [Reserved] (c) Ingestion of ice under the conditions of paragraph (e) of... by engine test under the following ingestion conditions: (1) Ice quantity will be the maximum...

14 CFR 33.77 - Foreign object ingestion-ice.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Foreign object ingestion-ice. 33.77 Section... object ingestion—ice. (a)-(b) [Reserved] (c) Ingestion of ice under the conditions of paragraph (e) of... by engine test under the following ingestion conditions: (1) Ice quantity will be the maximum...

Tooth wear risk assessment and care-planning in general dental practice.

PubMed

O'Toole, S; Khan, M; Patel, A; Patel, N J; Shah, N; Bartlett, D; Movahedi, S

2018-03-09

Objective To assess charting, risk assessment and treatment-planning of tooth wear between recently qualified and experienced dentists in general dental practice.Design Service evaluation.Setting Multi-setting evaluation of three mixed NHS/Private general dental practices in North-East London.Methods The clinical notes of new patient examinations on dentate adults presenting from the 1 October 2016 to 31 December 2016 were audited collecting data on tooth wear charting, risk assessment and treatment planning. Data were analysed using descriptives, chi square and logistic regressions in SPSS. Significance was inferred at p <0.05.Results Foundation dentists and experienced dentists performed 85 and 200 new patient examinations, respectively, during the evaluation period. Tooth wear was charted for 48% of those attending foundation dentists and 5% of those attending experienced dentists. Diet was assessed in 50.6% of patients examined by foundation dentists and 1.0% of patients examined by experienced dentists. Foundation dentists were more likely to chart tooth wear, risk assess and preventively manage tooth wear compared to experienced dentists (p <0.001).Conclusion This service evaluation highlights that improvements are required in recording, risk assessing and preventive treatment planning of erosive tooth wear. Experienced dentists were less likely to risk assess tooth wear and less likely to provide preventive treatment. Experienced GDPs may benefit from re-training in this area.

Wear particles and ions from cemented and uncemented titanium-based hip prostheses—A histological and chemical analysis of retrieval material

PubMed Central

Grosse, Susann; Haugland, Hans Kristian; Lilleng, Peer; Ellison, Peter; Hallan, Geir; Høl, Paul Johan

2015-01-01

Wear debris-induced inflammation is considered to be the main cause for periprosthetic osteolysis in total hip replacements (THR). The objective of this retrieval study was to examine the tissue reactions and exposure to metal ions and wear particles in periprosthetic tissues and blood samples from patients with titanium (Ti)-based hip prostheses that were revised due to wear, osteolysis, and/or aseptic loosening. Semiquantitative, histological tissue evaluations in 30 THR-patients revealed numerous wear debris-loaded macrophages, inflammatory cells, and necrosis in both groups. Particle load was highest in tissues adjacent to loosened cemented Ti stems that contained mainly submicron zirconium (Zr) dioxide particles. Particles containing pure Ti and Ti alloy elements were most abundant in tissues near retrieved uncemented cups. Polyethylene particles were also detected, but accounted only for a small portion of the total particle number. The blood concentrations of Ti and Zr were highly elevated in cases with high abrasive wear and osteolysis. Our findings indicate that wear particles of different chemical composition induced similar inflammatory responses, which suggests that particle size and load might be more important than the wear particle composition in periprosthetic inflammation and osteolysis. © 2014 The Authors. Journal of Biomedical Materials Research Part B: Applied Biomaterials Published by Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 103B:709–717, 2015. PMID:25051953

Long-term effects of the daily wear of senofilcon A silicone hydrogel contact lenses on corneal and conjunctival tissues.

PubMed

Guillon, Michel; Maïssa, Cécile

2010-12-01

The objective of the investigation was to show that, because of their overall properties, Acuvue® Oasys™ with Hydraclear® Plus brand (senofilcon A) silicone hydrogel contact lenses achieve excellent ocular tissue tolerance during long-term daily wear. The 2-year investigation was a prospective daily wear analysis of Acuvue® Oasys™ with Hydraclear® Plus (senofilcon A) silicone hydrogel contact lenses replaced every 2 weeks and used in conjunction with a representative range of care systems. The 2-year results compared with the subjects' baseline ocular status on entering the study revealed: The quantification of the effects on the ocular tissues of 2 years of daily wear of senofilcon A, by mainly previously successful daily soft contact lens wearers, showed an excellent biocompatibility. The results support the hypothesis that senofilcon A contact lenses, when worn on a 2-week daily wear regimen, maintain excellent long-term ocular tissue tolerance. Copyright © 2010 American Optometric Association. Published by Elsevier Inc. All rights reserved.

Study of wear mechanism of chopped fiber reinforced epoxy composite filled with graphite and bronze

NASA Astrophysics Data System (ADS)

Patil, Nitinchand; Prasad, Krishna

2018-04-01

The combined effect of graphite and sintered bronze with a short glass fiber reinforced epoxy composites was investigated in this work. A pin on disc wear test was carried out to study the wear behaviour and mechanism of the composites. The objective of this work is to develop an alternate friction resistance material for the application of sliding bearing. It was observed that the addition of sintered bronze improved mechanical and thermal stability of the composites as bronze has low contact resistance with graphite and has high thermal conductivity. It was observed from the test results that increased volume percentage of graphite and presence of bronze are play significant role in wear mechanism of the composites. It was observed from the scanning electronic microscopes (SEM) that the abrasive and adhesive wear mechanism was prominent in this study. It was also evident from the result that the frictional force remains stable irrespective of the applied normal load.

Space Wear Vision -Development of a Wardrobe for Life in Space Vehicles and Habitats

NASA Technical Reports Server (NTRS)

Orndorff, Evelyne

2015-01-01

A new vision is needed for the development of a wardrobe for NASA's journey to Mars in the 2030s. All human space missions require significant logistical mass and volume that add an unprecedented burden on long-duration missions beyond low-Earth orbit. The logistical burden is at least twice as great for prolonged exploration and settlements on planetary surfaces compared to missions in low-Earth orbit. The space wear vision is to design apparel that uniquely meets criteria and constraints for sustaining human presence in space. For long duration missions without landing on planetary surface, humans can use only what they carry in their spacecraft, while for settlements, additional resources may be available. The immediate space wear goal is to develop those elements needed for prolonged manned exploration beyond low Earth orbit. Three major objectives have been identified for achieving this goal: satisfying crew preferences, logistics reduction and repurposing, and systems integration. Garments must be comfortable, durable, safe to wear, and aesthetically pleasing. In addition, with limited cleaning resources, garments must be developed to reduce the logistical burden by reducing clothing mass and extending clothing wear. Furthermore, garments must have minimal impact on the life support systems of spacecraft. The approach to achieving the immediate space wear goal is to conduct multiple studies on Earth and on the International Space Station (ISS), thus laying out the path for finding materials and designing garments that meet the three objectives of prolonged manned exploration. Several studies have been undertaken recently for the first time, namely, to ascertain garment length of wear and to assess the acceptance of such extended wear. Most garments in these studies have been exercise T-shirts and shorts, and routine-wear T-shirts. Eleven studies have been completed: five studies of exercise T-shirts, three of exercise shorts, two of routine wear T-shirts, and one of shirts used as sleep-wear. The IVA (Intra Vehicular Activity) Clothing Study has been the first study with Roscosmos under the "Utilization Sharing Plan On-Board ISS," while the other studies have been conducted at the Johnson Space Center in a controlled environment similar to the ISS. For exercise clothing, study participants wore garments during aerobic exercise. For routine wear clothing, study participants wore the T-shirts daily in an office or laboratory. Daily questionnaires collected data on ordinal preferences of nine sensory elements and on reasons for retiring a used garment. More studies have been initiated on Earth, and some should be planned to engage more astronauts and cosmonauts in the design of the new space wear. Future studies will extend to other types of garments in the wardrobe; another will address microbial growth on textiles. Others will address cleaning and sanitation of clothing in space vehicles. Efforts will be made for additional ISS studies with NASA's international partners.

Randomized clinical study of wear of enamel antagonists against polished monolithic zirconia crowns

PubMed Central

Esquivel-Upshaw, J.F.; Kim, M.J.; Hsu, S.M.; Abdulhameed, N.; Jenkins, R.; Neal, D.; Ren, F.; Clark, A.E.

2018-01-01

Objectives To test the hypothesis that there is no difference in the in vivo maximum wear of enamel opposing monolithic zirconia crowns, enamel opposing porcelain fused to metal crowns and enamel opposing enamel. Methods Thirty patients needing single crowns were randomized to receive either a monolithic zirconia or metal-ceramic crown. Two non-restored opposing teeth in the same quadrants were identified to serve as enamel controls. After cementation, quadrants were scanned for baseline data. Polyvinylsiloxane impressions were obtained and poured in white stone. Patients were recalled at six-months and one-year for re-impression. Stone models were scanned using a tabletop laserscanner to determine maximum wear. Statistical analysis was performed using Mann-Whitney U to determine any significant differences between the wear of enamel against zirconia and metal-ceramic crowns. Results Sixteen zirconia and 14 metal-ceramic crowns were delivered. There were no statistical differences in mean wear of crown types (p = 0.165); enamel antagonists (p = 0.235) and enamel controls (p = 0.843) after one year. Conclusion Monolithic zirconia exhibited comparable wear of enamel compared with metal-ceramic crowns and control enamel after one year. Significance This study is clinically significant because the use of polished monolithic zirconia demonstrated comparable wear of opposing enamel to metal-ceramic and enamel antagonists. PMID:29042241

Objective Assessment of Ocular Surface Response to Contact Lens Wear in Presbyopic Contact Lens Wearers of Asian Descent.

PubMed

Guillon, Michel; Dumbleton, Kathy; Theodoratos, Panagiotis; Patel, Trisha; Karkkainen, Tom; Moody, Kurt

2018-05-01

Contact lens wearers of Asian descent may be predisposed to experience microtrauma of the ocular surface as a result a thinner post-lens tear film and higher eyelid tension, and these effects would be anticipated to be most marked in an older population. The objective of this study was to quantify the mechanical effects of the study contact lenses on the ocular surface in a population of presbyopic contact lens wearers of Asian descent. Twenty established presbyopic contact lens wearers (hydrogel n=5, none habitual wearers of etafilcon A lenses; silicone hydrogel n=15) of Asian descent were refitted with etafilcon A multifocal daily disposable contact lenses (1-DAY ACUVUE MOIST MULTIFOCAL) for a period of 1 month of daily lens wear. The habitual modalities of wear were 45% daily disposable and 55% planned replacement. Digital photographs of the upper lid margins, nasal and temporal conjunctiva, and superior cornea were taken after 6 hr of wear of the participants' habitual contact lenses, after 1 day without contact lens wear, and after 6 hr of wear of the study contact lenses at the end of the 1-month period. The photographs were masked according to study visit and the staining extent measured using proprietary software. Lid margin staining was significantly lower with the study contact lenses (2.0±1.0 mm) than with the participants' own contact lenses (3.2±3.0 mm) after 6 hr of wear, representing a mean staining decrease of 38% (P=0.010). Lid margin staining after 6 hr of wear of the study contact lenses was not different from that measured after 1 day without contact lenses (P=0.507). Limbal staining was also significantly less with the study contact lenses than with the participants' own contact lenses after 6 hr of wear (P=0.009). There was minimal upper corneal staining, and the degree was similar with the study and habitual lenses. Etafilcon A material, worn under a daily disposable modality, was shown to reduce upper lid margin and limbal staining in presbyopic contact lens wearers of Asian descent compared with the wearers' own contact lenses. Because of the high preponderance of dry eye amongst presbyopes, material selection is of importance and consideration should be given to the lens-ocular surface interaction.

Objective Assessment of Ocular Surface Response to Contact Lens Wear in Presbyopic Contact Lens Wearers of Asian Descent

PubMed Central

Dumbleton, Kathy; Theodoratos, Panagiotis; Patel, Trisha; Karkkainen, Tom; Moody, Kurt

2018-01-01

Introduction: Contact lens wearers of Asian descent may be predisposed to experience microtrauma of the ocular surface as a result a thinner post-lens tear film and higher eyelid tension, and these effects would be anticipated to be most marked in an older population. The objective of this study was to quantify the mechanical effects of the study contact lenses on the ocular surface in a population of presbyopic contact lens wearers of Asian descent. Methods: Twenty established presbyopic contact lens wearers (hydrogel n=5, none habitual wearers of etafilcon A lenses; silicone hydrogel n=15) of Asian descent were refitted with etafilcon A multifocal daily disposable contact lenses (1-DAY ACUVUE MOIST MULTIFOCAL) for a period of 1 month of daily lens wear. The habitual modalities of wear were 45% daily disposable and 55% planned replacement. Digital photographs of the upper lid margins, nasal and temporal conjunctiva, and superior cornea were taken after 6 hr of wear of the participants' habitual contact lenses, after 1 day without contact lens wear, and after 6 hr of wear of the study contact lenses at the end of the 1-month period. The photographs were masked according to study visit and the staining extent measured using proprietary software. Results: Lid margin staining was significantly lower with the study contact lenses (2.0±1.0 mm2) than with the participants' own contact lenses (3.2±3.0 mm2) after 6 hr of wear, representing a mean staining decrease of 38% (P=0.010). Lid margin staining after 6 hr of wear of the study contact lenses was not different from that measured after 1 day without contact lenses (P=0.507). Limbal staining was also significantly less with the study contact lenses than with the participants' own contact lenses after 6 hr of wear (P=0.009). There was minimal upper corneal staining, and the degree was similar with the study and habitual lenses. Conclusions: Etafilcon A material, worn under a daily disposable modality, was shown to reduce upper lid margin and limbal staining in presbyopic contact lens wearers of Asian descent compared with the wearers' own contact lenses. Because of the high preponderance of dry eye amongst presbyopes, material selection is of importance and consideration should be given to the lens–ocular surface interaction. PMID:27755285

15 CFR 930.121 - Consistent with the objectives or purposes of the Act.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Consistent with the objectives or... and Foreign Trade (Continued) NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE... Appeal to the Secretary for Review Related to the Objectives of the Act and National Security Interests...

Endodontic management of an unusual foreign body in a maxillary central incisor

PubMed Central

Chand, Keerthi; Joesph, Sam; Varughese, Jolly Mary; Nair, Mali G; Prasanth, Santhosh

2013-01-01

The discovery of foreign bodies in the teeth is often diagnosed accidentally. It is commonly seen in children. These foreign objects may act as a potential source of infection and may later lead to a painful condition. Detailed case history, clinical and radiographic examinations are necessary to come to a conclusion about the nature, size, and location of the foreign body, and the difficulty involved in its retrieval. This paper discusses the types of foreign objects found in and around the teeth and reports an unusual case of a stapler pin in the root canal of a tooth, its retrieval, and associated management of the involved teeth. PMID:24082582

Effect of Tape Burnishing and Drive Use on Head Wear in Rotary Tape Drives

NASA Astrophysics Data System (ADS)

Bhushan, Bharat; Anderson, Reid M.; Koinkar, Vilas N.

Three types of 12.7-mm wide metal particle tapes were studied. One of the tapes was calendered, whereas the other two tapes were additionally burnished one or two times using a proprietary process. Each type of tape was studied after 100 passes in the BetaCam SP drive and also in the virgin (0 pass) state. It was reported that in the case of the unburnished tape, head wear was high in the first pass and decreased during use. However, head wear for the double burnished tape was low for the first pass and increased during use. Whereas in the single burnished tape, head wear was low in the first pass and remained low. The objective of this study is to understand the mechanisms for loss and growth of head wear by correlating the surface characteristics of the tapes to head wear rate and to determine the changes in the surface characteristics occurring from 0 to 100 passes in the drive. It was found that summit density, mean and rms summit height, and mean and rms summit curvature correlate well to the head wear data. During manufacture and use in the drive, as the summit density, mean and rms summit height, and mean and rms summit curvature decrease, the head wear rate decreases. The mechanism for head wear is the initial ploughing of dense, sharp and high tape asperities into the surface of the head material resulting in a high head wear rate and a high coefficient of friction. Double burnishing during manufacturing removes high asperities, thus making the tape very smooth and possibly results in high adhesion and head wear growth with use. Chemical changes of the tape surface during double burnishing (not part of this study) also may be responsible for head wear growth during use.

Characterization of third-body media particles and their effect on in vitro composite wear

PubMed Central

Lawson, Nathaniel C.; Cakir, Deniz; Beck, Preston; Litaker, Mark S.; Burgess, John O.

2012-01-01

Objectives The purpose of this study was to compare four medium particles currently used for in vitro composite wear testing (glass and PMMA beads and millet and poppy seeds). Methods Particles were prepared as described in previous wear studies. Hardness of medium particles was measured with a nano-indentor, particle size was measured with a particle size analyzer, and the particle form was determined with light microscopy and image analysis software. Composite wear was measured using each type of medium and water in the Alabama wear testing device. Four dental composites were compared: a hybrid (Z100), flowable microhybrid (Estelite Flow Quick), micromatrix (Esthet-X), and nano-filled (Filtek Supreme Plus). The test ran for 100,000 cycles at 1.2Hz with 70N force by a steel antagonist. Volumetric wear was measured by non-contact profilometry. A two-way analysis of variance (ANOVA) and Tukey's test was used to compare both materials and media. Results Hardness values (GPa) of the particles are (glass, millet, PMMA, poppy respectively): 1.310(0.150), 0.279(.170), 0.279(0.095), and 0.226(0.146). Average particle sizes (μm) are (glass, millet, PMMA, poppy respectively): 88.35(8.24), 8.07(4.05), 28.95(8.74), and 14.08(7.20). Glass and PMMA beads were considerably more round than the seeds. During composite wear testing, glass was the only medium that produced more wear than the use of water alone. The rank ordering of the materials varied with each medium, however, the glass and PMMA bead medium allowed better discrimination between materials. Significance PMMA beads are a practical and relevant choice for composite wear testing because they demonstrate similar physical properties as seeds but reduce the variability of wear measurements. PMID:22578990

Rat Silicone Hydrogel Contact Lens Model: Effects of High vs. Low Dk Lens Wear

PubMed Central

Zhang, Yunfan; Gabriel, Manal M.; Mowrey-McKee, Mary F.; Barrett, Ronald P.; McClellan, Sharon; Hazlett, Linda D.

2012-01-01

Objectives This study used a rat contact lens (CL) model to test if high vs. low Dk lens wear caused changes in: 1) conjunctival Langerhans cell (LC) number or location; 2) Bcl-2 expression; and 3) infection risk. Methods Female, Lewis rats wore a high or low Dk CL continuously for 2 weeks. Afterward, corneas were harvested and processed for ADPase activity to identify Langerhans cells (LC), for immunostaining and for real time RT-PCR. CL wearing rats also were challenged with Pseudomonas aeruginosa by placing a bacterial-soaked CL on the eye followed by topical delivery of bacteria. After 48 hours, slit lamp examination and real time RT-PCR were used to evaluate the corneal response. Results Conjunctival LC were significantly increased after low vs. high Dk CL wear (p<0.0001). In contrast, conjunctival LC in non-lens wearing rats was not significantly different from the high Dk lens wearing group. Bcl-2 mRNA levels were significantly decreased in low vs. high Dk Cl wearing rats, while Bax, FasL, caspase 3 and caspase 9 levels were unchanged. Immunostaining for Bcl-2 showed fewer positively stained epithelial cells in the low vs. high Dk lens wearing group. After bacterial challenge, 30% of low vs. none of the high Dk CL wearing corneas became infected and showed increased mRNA levels for several pro-inflammatory cytokines/chemokines, inducible nitric oxide synthase (iNOS) and matrix metalloproteinase (MMP)-9. Conclusion Low vs. high Dk and/or no CL wear led to an increased number of conjunctival LC, decreased Bcl-2 levels, and increased the risk of bacterial infection. PMID:18997538

The validity of compliance monitors to assess wearing time of thoracic-lumbar-sacral orthoses in children with spinal cord injury.

PubMed

Hunter, Louis N; Sison-Williamson, Mitell; Mendoza, Melissa M; McDonald, Craig M; Molitor, Fred; Mulcahey, M J; Betz, Randal R; Vogel, Lawrence C; Bagley, Anita

2008-06-15

Prospective multicenter observation. To determine the validity of 3 commercially available at recording thoracic-lumbar-sacral orthosis (TLSO) wearing time of children with spinal cord injury (SCI) and to assess each monitor's function during daily activities. A major limitation to studies assessing the effectiveness of spinal prophylactic bracing is the patient's compliance with the prescribed wearing time. Although some studies have begun to use objective compliance monitors, there is little documentation of the validity of the monitors during activities of daily life and no comparisons of available monitors. Fifteen children with SCI who wore a TLSO for paralytic scoliosis were observed for 4 days during their rehabilitation stay. Three compliance monitors (2 temperature and 1 pressure sensitive) were mounted onto each TLSO. Time of brace wear from the monitors was compared with the wear time per day recorded in diaries. Observed versus monitored duration of brace wear found the HOBO (temperature sensitive) to be the most valid compliance monitor. The HOBO had the lowest average of difference and variance of difference scores. The correlation between the recorded daily entries and monitored brace wear time was also highest for the HOBO in analysis of dependent and independent scores. Bland-Altman plots showed that the pressure sensitive monitor underestimated wear time whereas the temperature monitors overestimated wear time. Compliance to prescribed wearing schedule has been a barrier to studying TLSO efficacy. All 3 monitors were found to measure TLSO compliance, but the 2 temperature monitors were more in agreement with the daily diaries. Based on its functional advantages compared with the HOBO, the StowAway TidbiT will be used to further investigate the long-term compliance of TLSO bracing in children with SCI.

Reduced wear of enamel with novel fine and nano-scale leucite glass-ceramics.

PubMed

Theocharopoulos, Antonios; Chen, Xiaohui; Hill, Robert; Cattell, Michael J

2013-06-01

Leucite glass-ceramics used to produce all-ceramic restorations can suffer from brittle fracture and wear the opposing teeth. High strength and fine crystal sized leucite glass-ceramics have recently been reported. The objective of this study is to investigate whether fine and nano-scale leucite glass-ceramics with minimal matrix microcracking are associated with a reduction in in vitro tooth wear. Human molar cusps (n=12) were wear tested using a Bionix-858 testing machine (300,000 simulated masticatory cycles) against experimental fine crystal sized (FS), nano-scale crystal sized (NS) leucite glass-ceramics and a commercial leucite glass-ceramic (Ceramco-3, Dentsply, USA). Wear was imaged using Secondary Electron Imaging (SEI) and quantified using white-light profilometry. Both experimental groups were found to produce significantly (p<0.05) less volume and mean-height tooth loss compared to Ceramco-3. The NS group had significantly (p<0.05) less tooth mean-height loss and less combined (tooth and ceramic) loss than the FS group. Increased waviness and damage was observed on the wear surfaces of the Ceramco-3 glass-ceramic disc/tooth group in comparison to the experimental groups. This was also indicated by higher surface roughness values for the Ceramco-3 glass-ceramic disc/tooth group. Fine and nano-sized leucite glass-ceramics produced a reduction in in vitro tooth wear. The high strength low wear materials of this study may help address the many problems associated with tooth enamel wear and restoration failure. Copyright © 2013 Elsevier Ltd. All rights reserved.

Two-body and three-body wear of glass ionomer cements.

PubMed

Kunzelmann, K H; Bürkle, V; Bauer, C

2003-11-01

Glass ionomer cements (GIC) have been modified in an attempt to improve their mechanical properties. The objective of the present paper was to compare the two-body and three-body wear of four modified GIC. The tested materials were Fuji IX (GC Corporation), Hi-Fi (Shofu) and Ketac Molar Aplicap (3M/ESPE). The cermet cement Ketac Silver Maxicap (3M/ESPE) was used as reference material. Two-body wear tests were carried out in the computer controlled 'artificial mouth' of the Munich Dental School, three-body wear was tested with the ACTA wear machine. The resulting average two-body wear rates (in microm) were: Fuji IX 327 (SD +/- 82) < Ketac Molar 379 (SD +/- 94) < Hi-Fi 376 (SD +/- 90) < Ketac silver 449 (SD +/- 127). The differences between the materials were significant (P < 0.05, ANOVA, modified LSD-test) with the exception of Ketac Molar and Hi-Fi. The average three-body wear rates (in microm) were: Hi-Fi 30 (SD +/- 10) < Ketac Molar +/- 42 (SD +/- 12) < Fuji IX 49 (SD +/- 14) < Ketac silver 73 (SD +/- 23). The difference between Ketac silver and the three other materials was significant (P < 0.05, ANOVA, modified LSD-test). No significant difference was calculated between Hi-Fi, Ketac Molar and Fuji IX. As Ketac Molar, Hi-Fi and Fuji IX show better wear resistance compared to Ketac silver both in occlusal-contact and contact-free areas, it may be assumed that the wear resistance of a glass ionomer cement may be improved more by changing the powder: liquid ratio than by incorporating silver particles into the glass powder.

Laser fragmentation of foreign bodies in the urinary tract: an in vitro study and clinical application.

PubMed

Bedke, Jens; Kruck, Stephan; Schilling, David; Matter, Anton; Horstmann, Marcus; Sievert, Karl-Dietrich; Stenzl, Arnulf; Nagele, Udo

2010-04-01

Foreign bodies of the urinary tract represent a urologic emergency. First-line treatment is endoscopic removal, but this is often impeded by restricted space, especially in the urethra. We postulated that foreign objects could be fragmented by Holmium:YAG laser and investigated its effect on objects of varying composition. In a specially designed stage flushed with physiologic saline, medical and non-medical objects of differing composition and diameter were subjected to fragmentation by Holmium:YAG at powers of 18 and 30 W. In additional thermal experiments, 5,000 J was applied to differing volumes of 0.9% sodium chloride. Experiments were repeated ten times. With one exception (16 Ch silicon catheter) all medical objects were fragmented (latex urinary catheter, ureteral stents, and guidewires). Of non-medical objects (wood, steel, copper, graphite, and nylon) only copper wire was not amenable to laser dissection. These in vitro results were applied in two patients who presented with a pencil (wood and graphite) in the urethra or bladder. After Holmium:YAG laser fragmentation, the pencil could be removed by forceps each. Foreign objects in the urinary tract can be fragmented with a Holmium:YAG laser. When foreign bodies are too big for initial endoscopic extraction, the clinician should consider this technique as a reasonable and atraumatic option to avoid open surgery.

The Tribology of Explanted Hip Resurfacings Following Early Fracture of the Femur.

PubMed

Lord, James K; Langton, David J; Nargol, Antoni V F; Meek, R M Dominic; Joyce, Thomas J

2015-10-15

A recognized issue related to metal-on-metal hip resurfacings is early fracture of the femur. Most theories regarding the cause of fracture relate to clinical factors but an engineering analysis of failed hip resurfacings has not previously been reported. The objective of this work was to determine the wear volumes and surface roughness values of a cohort of retrieved hip resurfacings which were removed due to early femoral fracture, infection and avascular necrosis (AVN). Nine resurfacing femoral heads were obtained following early fracture of the femur, a further five were retrieved due to infection and AVN. All fourteen were measured for volumetric wear using a co-ordinate measuring machine. Wear rates were then calculated and regions of the articulating surface were divided into "worn" and "unworn". Roughness values in these regions were measured using a non-contacting profilometer. The mean time to fracture was 3.7 months compared with 44.4 months for retrieval due to infection and AVN. Average wear rates in the early fracture heads were 64 times greater than those in the infection and AVN retrievals. Given the high wear rates of the early fracture components, such wear may be linked to an increased risk of femoral neck fracture.

Coating glass-ionomer cements with a nanofilled resin.

PubMed

Bonifácio, Clarissa Calil; Werner, Arie; Kleverlaan, Cornelis Johanes

2012-12-01

The objective of this study was to investigate the effect of a nanofilled resin coat on the flexural strength (FS) and the early wear (after 50,000 and 200,000 cycles) of the glass-ionomer cements Fuji IX GP Extra (FIXE) and Ketac Molar Aplicap (KM). Specimens were prepared and half of them were coated with G-Coat plus. The uncoated specimens were used as controls. Flexural strength (n = 10) was evaluated after 24 h using a 3-point bending test on a universal testing machine (ISO 9917-2). Wear (n = 20) was evaluated after 50,000 and 200,000 cycles using the ACTA wear machine. One-way, two-way ANOVA and Tukey post-hoc tests were used to analyze differences in FS and wear. For FIXE the coat significantly increased the FS and the wear along the two time spans. KM did not show a significant difference in FS with the coat. Improvements in wear were observed only after 50,000 cycles. Based on these laboratory results, it is concluded that G-coat Plus is indicated in association with GP IX Extra with the aim to improve the mechanical properties of the former. However, this study is limited to a short-term observation.

Detection of foreign body using fast thermoacoustic tomography with a multielement linear transducer array

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nie Liming; Xing Da; Yang Diwu

2007-04-23

Current imaging modalities face challenges in clinical applications due to limitations in resolution or contrast. Microwave-induced thermoacoustic imaging may provide a complementary modality for medical imaging, particularly for detecting foreign objects due to their different absorption of electromagnetic radiation at specific frequencies. A thermoacoustic tomography system with a multielement linear transducer array was developed and used to detect foreign objects in tissue. Radiography and thermoacoustic images of objects with different electromagnetic properties, including glass, sand, and iron, were compared. The authors' results demonstrate that thermoacoustic imaging has the potential to become a fast method for surgical localization of occult foreignmore » objects.« less

A case of stapler pin in the root canal--extending beyond the apex.

PubMed

Rao, A; Sudha, P

1999-01-01

There have been several reports describing the placement, by patients, of foreign objects into exposed pulp chambers and canals. In the present case, a 13-year-old patient reported with complaints of pain and a history of inserting a foreign object into the root canal of the left central incisor. On examination the foreign body was found to be a stapler pin which was projecting 5 millimeters from the apical foramen. Foreign bodies discovered from the root canal have varied from radiolucent objects like wooden tooth picks or tooth brush bristles to radioopaque materials like paper pins, needles, pencil leads etc. In the present case, despite our best efforts, the patient did not agree to undergo any treatment except for the extraction of the left central incisor.

Pediatric foreign bodies and their management.

PubMed

Kay, Marsha; Wyllie, Robert

2005-06-01

Ingestion of foreign bodies is a common pediatric problem, with more than 100,000 cases occurring each year. The vast majority of pediatric ingestions are accidental; increasing incidence of intentional ingestions starts in the adolescent age group. In the United States, the most common pediatric foreign bodies ingested are coins, followed by a variety of other objects, including toys, toy parts, sharp objects, batteries, bones, and food. In adolescents and adults, meat or food impactions are the most common accidental foreign body ingestion. Esophageal pathology underlies most cases of food impaction. Management of foreign body ingestions varies based on the object ingested, its location, and the patient's age and size. Esophageal foreign bodies as a group require early intervention because of their potential to cause respiratory symptoms and complications, esophageal erosions, or even an aortoesophageal fistula. Ingested batteries that lodge in the esophagus require urgent endoscopic removal even in the asymptomatic patient due to the high risk of complications. Sharp foreign bodies increase the foreign body complication rate from less than 1% to 15% to 35%, except for straight pins, which usually follow a relatively benign course unless multiple pins are ingested. Magnets are increasingly ingested, due to their ubiquitous nature and the perception that they do not pose a risk. Ingestion of multiple magnets creates a significant risk of obstruction, perforation, and fistula development. Methods to deal with foreign bodies include the suture technique, the double snare technique, and the combined forceps/snare technique for long, large, and sharp foreign bodies, along with newer equipment, such as retrieval nets and a variety of specialized forceps.

The relationship between back pain and lead apron use in radiologists.

PubMed

Moore, B; vanSonnenberg, E; Casola, G; Novelline, R A

1992-01-01

Anecdotal experience has suggested that back pain in radiologists may result from extensive wearing of lead aprons. To investigate this possibility, we sent questionnaires to 688 radiologists in various subspecialties whose use of lead aprons varied from none to moderate to extensive. The questionnaire included both objective items that quantitated apron use and back pain and subjective items that asked, for example, if the respondent believed that lead aprons were responsible for his or her back pain. We received 236 responses (34% response rate). Objective data from those radiologists who had experienced no back pain before wearing a lead apron (179 radiologists, 26% of those surveyed) were tabulated; respondents were grouped according to age, time spent wearing a lead apron, and degree of back pain. Odds ratios were calculated. Answers to subjective questions for all respondents were tabulated. Back pain was reported by 52% of those who estimated their lead apron use at greater than or equal to 10 hr per week, the mean response, as opposed to 46% of those who wore lead aprons fewer than 10 hr a week. These and related results were not statistically significant. Our study does not prove that wearing a lead apron is a significant risk factor for the development of back pain.

Foreign Languages: A Guide to Curriculum Development [Revision].

ERIC Educational Resources Information Center

Connecticut State Board of Education, Hartford.

The guide is designed to help school district planners develop and implement suitable foreign language curricula. Focusing on programs in grades K-12, it provides an overview of current philosophies, objectives, methods, and materials in foreign language education; illustrates how these may be implemented in a sequential foreign language program…

Tooth wear and the role of salivary measures in general practice patients

PubMed Central

Rothen, Marilynn; Scott, JoAnna; Cunha-Cruz, Joana

2014-01-01

Objectives The goal of this study was to investigate the association between tooth wear and salivary measures in a random sample of patients from practices of dentist members of a practice-based research network. Materials and methods Patients completed a questionnaire on oral self-care, health, dietary habits, medications, and socio-demographic variables. Six salivary characteristics (consistency, resting salivary flow, resting salivary pH, stimulated salivary flow, stimulated salivary pH, and buffering capacity) were measured, and a dental examination included categorizing patients according to the dentist’s judgment of the degree of tooth wear (i.e., none/minimal, some, or severe/extreme). Bivariate and multinomial logistic regression models were used to relate salivary characteristics and other factors to the outcome of tooth wear. Results Data are reported from 1,323 patients (age range 16–97 years) from 61 practices. Patient age, gender, number of teeth, and perception of dry mouth were associated with tooth wear, but salivary and dietary factors were either weakly or not related. Conclusions The findings of this cross-sectional assessment suggest that using these salivary tests and dietary assessments in real-life clinical settings is unlikely to be useful in assessing tooth wear risk. Suggestions are offered about risk assessment for tooth wear. Clinical relevance Assessing a dental patient’s risk of tooth wear using salivary measures and dietary assessments as described is not recommended for general dental practice until stronger evidence exists indicating its utility. PMID:24647789

Pattern of seat belt wearing in Nanjing, China

PubMed Central

Routley, V; Ozanne‐Smith, J; Li, D; Hu, X; Wang, P; Qin, Y

2007-01-01

Objective To describe the patterns of seat belt wearing in Nanjing, China for drivers, front seat passengers, and rear occupants of motor vehicles. Design Roadside observational study. Setting Four sites in central and northern Nanjing during daylight hours over 1 week in April 2005. Subjects Drivers and passengers of 17 147 cars, taxis, goods vans, and pickups, which traveled in the inside traffic lane. Main outcome measures Percentage seat belt wearing for each of seating position, age/sex, time of day, vehicle type, day of week. Results The rate of seat belt wearing was significantly higher in drivers (67.3%, 95% CI 66.6 to 68.0) than front seat passengers (18.9%, 95% CI, 18.0 to 19.8). It was negligible for second front seat passengers (2.6%, 95% CI 0.3 to 4.9) and rear seat passengers (0.5%, 95% CI 0.3 to 0.7). Belt tampering, such that protection would be reduced in the event of a crash, was observed for 18.5% of taxi drivers. Drivers were most likely to wear seat belts in cars and vans and at a city roundabout; front seat passengers were most likely to wear seat belts in non‐taxi vehicles, during the evening rush hour, if the driver was wearing a belt, and on the local north road. Drivers were least likely to wear a belt in the early morning, in pickups and taxis, on Tuesday (or the following week), and on the local north road; front seat passengers were least likely to wear a belt in taxis and if the driver was not wearing a belt. Conclusions Rates of seat belt wearing by passengers were low despite national legislation and provincial regulations coming into effect several months before the survey. Combined education and enforcement are necessary accompaniments to legislation. PMID:18056315

Influence of country of study on student responsiveness to the H1N1 pandemic.

PubMed

Griffiths, S M; Wong, A H; Kim, J H; Yung, T K C; Lau, J T F

2010-08-01

University students, both travelling abroad on holiday or exchange students entering a country, can serve as mobile carriers of infectious diseases during a pandemic, and thus require special attention when considering preventive measures. The objectives of this study were to evaluate student compliance and opinions on preventive measures of a university before and during an H1N1 influenza pandemic, and to explore environmental and behavioural factors that might contribute towards compliance. Cross-sectional, self-administered questionnaire. Local and foreign students attending an international summer school programme were invited to participate in a self-administered survey. Respondents complied with most of the preventive measures, excluding website viewing and mask wearing. Significant differences in compliance and perceived necessity were found amongst students from Singapore, Hong Kong and the USA. Singaporean students were significantly more likely to comply with all measures and consume antiviral medication in response to the pandemic than students studying in the US. Students' responses towards university pandemic measures were largely positive, but sensitivity towards these measures varied between groups by country of study. This should be considered in further comparative studies. Copyright 2010 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

Report on the Audit of Foreign Military Sales Trust Fund Disbursement Reporting

DTIC Science & Technology

1991-09-11

This is our final report on the Audit of Foreign Military Sales Trust Fund Disbursement Reporting, provided for your information and use. The audit was...made from August 1990 through March 1991. The overall objective of the audit was to determine whether disbursements from the Foreign Military Sales...implementation of the internal management control program required by the Federal Managers’ Financial Integrity Act (FMFIA) as it pertained to the audit objectives.

Foreign bodies in the larynx and tracheobronchial tree in children. A review of 225 cases.

PubMed

Rothmann, B F; Boeckman, C R

1980-01-01

In a study of 225 patients with foreign bodies in the larynx, trachea and bronchi, 77% were 36 months of age or less. The male-female ratio was 2:1. Food or food derivatives were the causative agent in 70% of the cases, with 38% due to a portion of nut. The foreign body involved the right and left bronchus with equal frequency. A choking episode followed by an audible wheeze (55%) was the most common presenting complaint. Obstructive emphysema was demonstrated in 60% and was best demonstrated by inspiration-expiration chest roentgenograms or fluoroscopy. A radio-opaque object was seen in 13%. Two hundred ten foreign objects (93%) were removed by endoscopy. Four patients required pulmonary resection for bronchiectasis and in three patients bronchotomy was performed. Five patients expelled the foreign body spontaneously, two patients were transferred to another hospital, and one foreign body was not recovered. There was no mortality.

Overtube-Assisted Foreign Body Removal: A Review of Endoscopic Management and Case Illustration.

PubMed

Ofosu, Andrew; Ramai, Daryl; Reddy, Madhavi

2017-09-29

The ingestion of foreign bodies is a common medical emergency seen in both adults and children. In children, the most commonly ingested foreign bodies include coins, toys, magnets, and batteries. In adults, food bolus impaction represents the most common cause of foreign body ingestion. The majority of foreign bodies pass spontaneously. Sharp or pointed objects increase the risk of perforation. Emergent endoscopic intervention is indicated in cases of esophageal obstruction, ingestion of disk batteries, and sharp pointed objects in the esophagus. Flexible endoscopy is the therapeutic method of choice for removing foreign bodies. It is preferred due to its high success rate and low risk for complications. Additionally, the use of an overtube provides gastric and esophageal protection from mucosal laceration. We present a 27-year-old male who ingested six razor blades and a curtain hook and review endoscopic management.

Faculty Member's Guide to U.S. Immigration Law.

ERIC Educational Resources Information Center

Smith, Eugene H.; Baron, Marvin

Immigration laws and regulations are briefly summarized to aid faculty members in understanding problems faced by foreign students and scholars. The objective is to enable faculty to properly advise foreign students regarding their academic programs and to recognize when a foreign student or scholar needs to be referred to the foreign student…

Esophageal foreign bodies in pediatric patients: a thirteen-year retrospective study.

PubMed

Rybojad, Beata; Niedzielska, Grazyna; Niedzielski, Artur; Rudnicka-Drozak, Ewa; Rybojad, Pawel

2012-01-01

We discuss clinical symptoms and radiological findings of variable esophageal foreign bodies as well as therapeutic procedures in Caucasian pediatric patients. A retrospective study of 192 cases of suspected esophageal foreign bodies between 1998 and 2010 was conducted. Data were statistically analyzed by chi-square test. A foreign body was removed from a digestive tract of 163 children aged 6 months to 15 years (mean age 4.9). Most objects were located within cricopharyngeal sphincter. Dysphagia occurred in 43%, followed by vomiting (29%) and drooling (28%). The most common objects were coins. Plain chest X-rays demonstrated aberrations in 132 cases, and in doubtful situations an esophagram test was ordered. In the group of thirty-seven patients whose radiograms were normal, esophagoscopy revealed fifteen more objects, which were eventually successfully removed. No major complications occurred. Esophagram should be a second X-ray examination if an object is not detected in plain chest X-ray. We recommend a rigid esophagoscopy under general anesthesia in doubtful cases as a safe treatment for pediatric patients.

Tensile and tribological properties of a short-carbon-fiber-reinforced peek composite doped with carbon nanotubes

NASA Astrophysics Data System (ADS)

Li, J.; Zhang, L. Q.

2009-09-01

The main objective of this paper is to develop a high-wear-resistant short-carbon-fiber-reinforced polyetheretherketone (PEEK) composite by introducing additional multiwall carbon nanotubes (MWCNTs) into it. The compounds were mixed in a Haake batch mixer and fabricated into sheets by compression molding. Samples with different aspect ratios and concentrations of fillers were tested for wear resistance. The worn surfaces of the samples were examined by using a scanning electron microscope (SEM), and the photomicrographs revealed a higher wear resistance of the samples containing the additional carbon nanotubes. Also, a better interfacial adhesion between the short carbon fibers and vinyl ester in the composite was observed.

A probabilistic-based approach to monitoring tool wear state and assessing its effect on workpiece quality in nickel-based alloys

NASA Astrophysics Data System (ADS)

Akhavan Niaki, Farbod

The objective of this research is first to investigate the applicability and advantage of statistical state estimation methods for predicting tool wear in machining nickel-based superalloys over deterministic methods, and second to study the effects of cutting tool wear on the quality of the part. Nickel-based superalloys are among those classes of materials that are known as hard-to-machine alloys. These materials exhibit a unique combination of maintaining their strength at high temperature and have high resistance to corrosion and creep. These unique characteristics make them an ideal candidate for harsh environments like combustion chambers of gas turbines. However, the same characteristics that make nickel-based alloys suitable for aggressive conditions introduce difficulties when machining them. High strength and low thermal conductivity accelerate the cutting tool wear and increase the possibility of the in-process tool breakage. A blunt tool nominally deteriorates the surface integrity and damages quality of the machined part by inducing high tensile residual stresses, generating micro-cracks, altering the microstructure or leaving a poor roughness profile behind. As a consequence in this case, the expensive superalloy would have to be scrapped. The current dominant solution for industry is to sacrifice the productivity rate by replacing the tool in the early stages of its life or to choose conservative cutting conditions in order to lower the wear rate and preserve workpiece quality. Thus, monitoring the state of the cutting tool and estimating its effects on part quality is a critical task for increasing productivity and profitability in machining superalloys. This work aims to first introduce a probabilistic-based framework for estimating tool wear in milling and turning of superalloys and second to study the detrimental effects of functional state of the cutting tool in terms of wear and wear rate on part quality. In the milling operation, the mechanisms of tool failure were first identified and, based on the rapid catastrophic failure of the tool, a Bayesian inference method (i.e., Markov Chain Monte Carlo, MCMC) was used for parameter calibration of tool wear using a power mechanistic model. The calibrated model was then used in the state space probabilistic framework of a Kalman filter to estimate the tool flank wear. Furthermore, an on-machine laser measuring system was utilized and fused into the Kalman filter to improve the estimation accuracy. In the turning operation the behavior of progressive wear was investigated as well. Due to the nonlinear nature of wear in turning, an extended Kalman filter was designed for tracking progressive wear, and the results of the probabilistic-based method were compared with a deterministic technique, where significant improvement (more than 60% increase in estimation accuracy) was achieved. To fulfill the second objective of this research in understanding the underlying effects of wear on part quality in cutting nickel-based superalloys, a comprehensive study on surface roughness, dimensional integrity and residual stress was conducted. The estimated results derived from a probabilistic filter were used for finding the proper correlations between wear, surface roughness and dimensional integrity, along with a finite element simulation for predicting the residual stress profile for sharp and worn cutting tool conditions. The output of this research provides the essential information on condition monitoring of the tool and its effects on product quality. The low-cost Hall effect sensor used in this work to capture spindle power in the context of the stochastic filter can effectively estimate tool wear in both milling and turning operations, while the estimated wear can be used to generate knowledge of the state of workpiece surface integrity. Therefore the true functionality and efficiency of the tool in superalloy machining can be evaluated without additional high-cost sensing.

Impalement of an unusual foreign body on the temporomandibular joint causing severe trismus.

PubMed

Ito, Ryohei; Kubota, Kosei; Furudate, Ken; Nakagawa, Hiroshi; Kon, Takao; Tamura, Yoshihiro; Kobayashi, Wataru

2016-12-01

A penetrating injury by a foreign body is comparatively common in the oral and maxillofacial region. On the other hand, injury to the temporomandibular joint (TMJ) by a foreign object is very rare. The TMJ is an anatomically narrow space surrounded by hard bony processes. An unusual case of trauma with severe trismus caused by a foreign body that impaled the TMJ is reported. A 55-year-old man presented with a 5 × 1-cm laceration to the right cheek caused by a flying object propelled during the use of a lawn mower. The edge of the foreign body had a metallic wire, which became imbedded in the wound. His jaw opening was severely limited. Computed tomography revealed that the foreign body was 3 mm in diameter and was impaled on the articular capsule. The object was successfully removed, and the wound and interior of the TMJ were irrigated. Rehabilitation of mouth opening was started on postoperative day 3. On day 9, mouth opening had improved to 35 mm, and he was discharged. After 1 year, mouth opening was 45 mm with no sign of any TMJ disorders. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Frequency of Obstructive Sleep Apnea Syndrome in Dental Patients with Tooth Wear

PubMed Central

Durán-Cantolla, Joaquín; Alkhraisat, Mohammad Hamdan; Martínez-Null, Cristina; Aguirre, Jose Javier; Guinea, Elena Rubio; Anitua, Eduardo

2015-01-01

Study Objectives: To estimate the frequency of obstructive sleep apnea syndrome (OSAS) in dental patients with tooth wear, and to assess the role of dentists in the identification of patients at risk of OSAS. Methods: Dental patients with tooth wear and treated with occlusal splint were prospectively recruited to perform sleep study. The severity of tooth wear was established by the treating dentist before patient referral to sleep disorders unit. Sleep questionnaires, anthropometric measurements, and validated respiratory polygraphy were performed. Results: All patients with dental wear were offered a sleepiness analysis. Of 31 recruited patients, 30 (77% males) participated in this study. Patients' mean age was 58.5 ± 10.7 years (range: 35–90 years) and the body mass index was 27.9 ± 3.4 kg/m2. Tooth wear was mild in 13 patients, moderate in 8 and severe in 9. The mean apnea-hypopnea index (AHI) was 32.4 ± 24.9. AHI < 5 was reported in 2 patients, AHI of 5–29 in 17, and AHI ≥ 30 in 11. A statistically significant association was found between AHI severity and tooth wear severity (Spearman R = 0.505; p = 0.004). Conclusions: Tooth wear could be a tool to identify those patients at risk of having OSAS. This highlights the importance of dental professionals to identify and refer patients with OSAS. Citation: Durán-Cantolla J, Alkhraisat MH, Martínez-Null C, Aguirre JJ, Guinea ER, Anitua E. Frequency of obstructive sleep apnea syndrome in dental patients with tooth wear. J Clin Sleep Med 2015;11(4):445–450. PMID:25665693

Device for removing foreign objects from anatomic organs

NASA Technical Reports Server (NTRS)

Angulo, Earl D. (Inventor)

1992-01-01

A device is disclosed for removing foreign objects from anatomic organs such as the ear canal or throat. It has a housing shaped like a flashlight, an electrical power source such as a battery or AC power from a wall socket, and a tip extending from the housing. The tip has at least one wire loop made from a shape-memory-effect alloy, such as Nitinol, switchably connected to the electrical power source such that when electric current flows through the wire loop the wire loop heats up and returns to a previously programmed shape such as a curet or tweezers so as to facilitate removal of the foreign object.

Biotribological evaluation of artificial disc arthroplasty devices: influence of loading and kinematic patterns during in vitro wear simulation.

PubMed

Grupp, Thomas M; Yue, James J; Garcia, Rolando; Basson, Janet; Schwiesau, Jens; Fritz, Bernhard; Blömer, Wilhelm

2009-01-01

Wear simulation is an essential pre-clinical method to predict the mid- and long-term clinical wear behavior of newly introduced devices for total disc arthroplasty. The main requirement of a suitable method for spinal wear simulation has to be the ability to distinguish between design concepts and allow for a direct comparison of predicate devices. The objective of our study was to investigate the influence of loading and kinematic patterns based on two different protocols for spinal wear simulation (ISO/FDIS 18192-1 (2006) and ASTM F2423-05). In vitro wear simulation was performed with six activ L lumbar artificial disc devices (Aesculap Tuttlingen, Germany). The applied kinematic pattern of movement was multidirectional for ISO (elliptic track) and unidirectional with a curvilinear shape for ASTM. Testing was done for 10 million cycles in the ISO loading mode and afterwards with the same specimens for 5 million cycles according to the ASTM protocol with a customized six-station servohydraulic spinal wear simulator (EndoLab Thansau, Germany). Gravimetrical and geometrical wear assessment, a slide track analysis correlated to an optical surface characterization, and an estimation of particle size and morphology were performed. The gravimetric wear rate for the first 10 million cycles was ISO(initial) = 2.7 +/- 0.3 mg/million cycles. During the ASTM test period (10-15 million cycles) a gravimetric wear rate of 0.14 +/- 0.06 mg/million cycles was estimated. The wear rates between the ISO and ASTM driven simulations differ substantially (approximately 20-fold) and statistical analysis demonstrates a significant difference (p < 0.001) between the test groups. The main explanation of divergency between ISO and ASTM driven wear simulations is the multidirectional pattern of movement described in the ISO document resulting in a cross-shear stress on the polyethylene material. Due to previous retrieval observations, it seems to be very unlikely that a lumbar artificial disc is loaded with a linear wear path.Testing according to ASTM F2423-05 with pure unidirectional motion does not reflect the kinematics of TDA patients' daily activities. Based on our findings it seems to be more reliable to predict the clinical wear behavior of an artificial disc replacement using the ISO/FDIS 18192-1 method.

Biotribological evaluation of artificial disc arthroplasty devices: influence of loading and kinematic patterns during in vitro wear simulation

PubMed Central

Yue, James J.; Garcia, Rolando; Basson, Janet; Schwiesau, Jens; Fritz, Bernhard; Blömer, Wilhelm

2008-01-01

Wear simulation is an essential pre-clinical method to predict the mid- and long-term clinical wear behavior of newly introduced devices for total disc arthroplasty. The main requirement of a suitable method for spinal wear simulation has to be the ability to distinguish between design concepts and allow for a direct comparison of predicate devices. The objective of our study was to investigate the influence of loading and kinematic patterns based on two different protocols for spinal wear simulation (ISO/FDIS 18192-1 (2006) and ASTM F2423-05). In vitro wear simulation was performed with six activ® L lumbar artificial disc devices (Aesculap Tuttlingen, Germany). The applied kinematic pattern of movement was multidirectional for ISO (elliptic track) and unidirectional with a curvilinear shape for ASTM. Testing was done for 10 million cycles in the ISO loading mode and afterwards with the same specimens for 5 million cycles according to the ASTM protocol with a customized six-station servohydraulic spinal wear simulator (EndoLab Thansau, Germany). Gravimetrical and geometrical wear assessment, a slide track analysis correlated to an optical surface characterization, and an estimation of particle size and morphology were performed. The gravimetric wear rate for the first 10 million cycles was ISOinitial = 2.7 ± 0.3 mg/million cycles. During the ASTM test period (10–15 million cycles) a gravimetric wear rate of 0.14 ± 0.06 mg/million cycles was estimated. The wear rates between the ISO and ASTM driven simulations differ substantially (approximately 20-fold) and statistical analysis demonstrates a significant difference (p < 0.001) between the test groups. The main explanation of divergency between ISO and ASTM driven wear simulations is the multidirectional pattern of movement described in the ISO document resulting in a cross-shear stress on the polyethylene material. Due to previous retrieval observations, it seems to be very unlikely that a lumbar artificial disc is loaded with a linear wear path.Testing according to ASTM F2423-05 with pure unidirectional motion does not reflect the kinematics of TDA patients‘ daily activities. Based on our findings it seems to be more reliable to predict the clinical wear behavior of an artificial disc replacement using the ISO/FDIS 18192-1 method. PMID:19050942

Effect of power toothbrushing on simulated wear of dental cement margins.

PubMed

Black, Marsha A; Bayne, Stephen C; Peterson, Charlotte A

2007-01-01

Power toothbrushes (PTBs), in combination with abrasive dentifrices, may encourage wear of dental cements at crown margins. The objective of this in vitro simulation was to control the clinical variables associated with PTB use and measure the potential side effects of PTBs with mild and abrasive dentifrices. Four PTBs ( Braun-Oral-B-Professional Care at 150 g brushing force, Sonicare-Elite at 90 g, Colgate-Actibrush at 200 g and Crest-Spinbrush-Pro at 250 g) and 2 dentifrices mixed 1:1 with tap water (Mild= Colgate-Total, Colgate-Palmolive; Abrasive= Close-up, Chesebrough-Ponds) versus tap water alone (control) were used to abrade 2 cements (Fleck's Mizzy Zinc Phosphate [ZP]; 3M-ESPE Unicem universal cement [UC]) using cement-filled slots (160 m wide) cut into wear-resistant ceramic blocks. A custom fixture controlled PTB/block alignment, PTB loads, and other testing variables. Wear was measured (3 profilometer traces/slot, 5 slots/block/group, baseline to 5-year differences) and analyzed (3-way ANOVA, p < or = 0.05, Bonferroni). Wear for ZP was much greater than UC (p<0.05) for all 4 PTBs and both dentifrices. Brushing with water showed no effects (p<0.05). Cement-PTB-dentifrice interactions did occur. Only minor differences occurred among PTBs. Pooled 5y-wear levels for ZP for both dentifrices approximately 21 microm /5y) were similar to values for current-day posterior composite materials. Combinations of PTBs with mild and abrasive dentifrices produced significant wear with ZP but not UC; thus, resin-composite cements seem to represent a better choice for wear resistance.

A combined experimental and finite element approach to analyse the fretting mechanism of the head-stem taper junction in total hip replacement.

PubMed

Bitter, Thom; Khan, Imran; Marriott, Tim; Lovelady, Elaine; Verdonschot, Nico; Janssen, Dennis

2017-09-01

Fretting corrosion at the taper interface of modular hip implants has been implicated as a possible cause of implant failure. This study was set up to gain more insight in the taper mechanics that lead to fretting corrosion. The objectives of this study therefore were (1) to select experimental loading conditions to reproduce clinically relevant fretting corrosion features observed in retrieved components, (2) to develop a finite element model consistent with the fretting experiments and (3) to apply more complicated loading conditions of activities of daily living to the finite element model to study the taper mechanics. The experiments showed similar wear patterns on the taper surface as observed in retrievals. The finite element wear score based on Archard's law did not correlate well with the amount of material loss measured in the experiments. However, similar patterns were observed between the simulated micromotions and the experimental wear measurements. Although the finite element model could not be validated, the loading conditions based on activities of daily living demonstrate the importance of assembly load on the wear potential. These findings suggest that finite element models that do not incorporate geometry updates to account for wear loss may not be appropriate to predict wear volumes of taper connections.

Tooth wear against ceramic crowns in posterior region: a systematic literature review

PubMed Central

Hmaidouch, Rim; Weigl, Paul

2013-01-01

The objective of this systematic review was to assess tooth wear against ceramic crowns in posterior region in vitro and in vivo. An electronic PubMed search was conducted to identify studies on tooth wear against ceramic crowns in posterior region. The selected studies were analyzed in regard to type of crowns, natural antagonist, measuring protocol and outcome. From a yield of 1 000 titles, 43 articles were selected for full-text analysis; finally, no in vitro and only five in vivo studies met the inclusion criteria. As there is heterogeneity in design, used measuring method, ceramics and analysis-form, a meta-analysis was not possible. Results of these studies are very controversial which makes a scientifically valid comparison impossible. This review indicated that some all-ceramic crowns are as wear friendly as metal-ceramic crowns. Up to now, it has been impossible to associate tooth wear with any specific causal agent. The role of ceramic surface treatment that might be responsible for the changing in rate of tooth wear seems undetermined as yet through clinical trials. The literature reveals that studies on this topic are subject to a substantial amount of bias. Therefore, additional clinical studies, properly designed to diminish bias, are warranted. PMID:24136675

Glenoid wear after shoulder hemiarthroplasty: quantitative radiographic analysis.

PubMed

Parsons, I M; Millett, Peter J; Warner, Jon J P

2004-04-01

Symptomatic glenoid arthrosis may limit the long-term success of shoulder hemiarthroplasty in patients who are young and functionally demanding. The principal objective of the current study was to quantify glenoid wear after proximal humeral replacement in young, active subjects. Eight patients, ages 21 to 60 years (mean, 45 years), met inclusion criteria. The mean followup was 43 months. Functional scores for the cohort averaged 60% of age and gender-adjusted healthy subjects (range, 28%-84%). Glenohumeral joint space was measured on serial axillary radiographs using a Microscribe 3-DX digitizing device (measurement accuracy, 0.23 mm). Progressive glenoid wear was found in all eight patients. The mean decrease was 2 mm (range, 1.3-2.8 mm), a 68% decrease in glenohumeral joint space. Glenoid cartilage wear also was correlated with Constant and Murley scores. Patients with residual joint spaces less than 1 mm had a mean score of 50%, compared with a score of 71% for patients with joint spaces greater than 1 mm. There were no correlations between wear and mechanism of injury, duration of symptoms, and prior surgery. This study suggests that glenoid cartilage erosion can be expected routinely after humeral head replacement in young, active individuals, and that such wear may adversely affect function or necessitate conversion to total shoulder arthroplasty.

Foreign Investment in the U.S.: Costs and Benefits. Headline Series 249.

ERIC Educational Resources Information Center

Zupnick, Elliot

The document discusses the implications and positive and negative aspects of foreign direct investment in the United States. The objective is to determine whether a restrictive U.S. policy as it relates to foreign direct investment in the United States is desirable. It is presented in five chapters. Chapter I defines foreign direct investment…

Simulations in Foreign Languages.

ERIC Educational Resources Information Center

Nebraska State Dept. of Education, Lincoln. Div. of Instructional Services.

The purpose of this publication is to define minimal competencies for foreign language classes. The term "simulation" refers to role playing. The simulations are stated in terms of practical communication performance objectives. The intent is to have the student direct his learning in the basic skills toward an immediate objective rather than a…

Governmental Objectives in Exchanges of Persons Programs.

ERIC Educational Resources Information Center

Harkness, Albert, Jr.

The paper questions whether educational and cultural activities sponsored by the United States government should be aimed at foreign policy objectives or should be treated as ends in themselves. Arguments are presented by political leaders, educators, and government officials in favor of and against cultural exchange as a form of foreign policy…

Predicting knee replacement damage in a simulator machine using a computational model with a consistent wear factor.

PubMed

Zhao, Dong; Sakoda, Hideyuki; Sawyer, W Gregory; Banks, Scott A; Fregly, Benjamin J

2008-02-01

Wear of ultrahigh molecular weight polyethylene remains a primary factor limiting the longevity of total knee replacements (TKRs). However, wear testing on a simulator machine is time consuming and expensive, making it impractical for iterative design purposes. The objectives of this paper were first, to evaluate whether a computational model using a wear factor consistent with the TKR material pair can predict accurate TKR damage measured in a simulator machine, and second, to investigate how choice of surface evolution method (fixed or variable step) and material model (linear or nonlinear) affect the prediction. An iterative computational damage model was constructed for a commercial knee implant in an AMTI simulator machine. The damage model combined a dynamic contact model with a surface evolution model to predict how wear plus creep progressively alter tibial insert geometry over multiple simulations. The computational framework was validated by predicting wear in a cylinder-on-plate system for which an analytical solution was derived. The implant damage model was evaluated for 5 million cycles of simulated gait using damage measurements made on the same implant in an AMTI machine. Using a pin-on-plate wear factor for the same material pair as the implant, the model predicted tibial insert wear volume to within 2% error and damage depths and areas to within 18% and 10% error, respectively. Choice of material model had little influence, while inclusion of surface evolution affected damage depth and area but not wear volume predictions. Surface evolution method was important only during the initial cycles, where variable step was needed to capture rapid geometry changes due to the creep. Overall, our results indicate that accurate TKR damage predictions can be made with a computational model using a constant wear factor obtained from pin-on-plate tests for the same material pair, and furthermore, that surface evolution method matters only during the initial "break in" period of the simulation.

A foreign body in disguise.

PubMed

Leith, R; O'Connell, A C

2013-10-01

Young children habitually place objects in their mouths to discover and learn about the world and it is considered a normal stage of early childhood development. Ingestion and aspiration of foreign objects predominantly occurs in preschool toddlers with a peak incidence at age three years, and can have serious consequences. A 2-year-old boy presented to the Dublin Dental University Hospital with a tooth-coloured mass tightly adherent to a lower primary incisor. The lesion surrounded the cervical third of the crown on the lower right primary central incisor and extended subgingivally. The tooth was mobile but with minimal inflammation. The tooth was subsequently extracted under general anaesthesia to reveal that the mass was in fact a foreign body, although this was originally thought unlikely as a cause. The patient underwent an unremarkable recovery. The case of a foreign body disguised as a tooth-like abnormality was only identified under general anaesthesia, and even then it was impossible to prise the object from the tooth in situ. Misdiagnosis of impacted foreign bodies in young children presents complicated diagnostic problems.

Emergency endoscopic management of dietary foreign bodies in the esophagus.

PubMed

Lin, Hsuan-Hwai; Lee, Shih-Chun; Chu, Heng-Cheng; Chang, Wei-Kuo; Chao, You-Chen; Hsieh, Tsai-Yuan

2007-07-01

We report our experience of endoscopy in the emergency management of dietary foreign bodies. One hundred thirty-six patients were admitted to the emergency department (ED) between January 1997 and October 2006 for the endoscopic removal of esophageal dietary foreign bodies. They had a mean age of 47.7 years, and 91 (67%) were women. Most of the ingested materials (98.5%) were successfully extracted using either flexible or rigid endoscope. The objects most frequently ingested were fish bones (48%) and chicken bones (46%). Most of the objects (84%) were lodged in the upper esophagus. Two patients with irretrievable foreign bodies or complicated perforations were taken to surgery. Because most of these foreign bodies lodged in the upper esophagus, physicians should take care of this area to avoid secondary injury or complications, especially with sharp bones.

Clinical study of the influence of preoperative wearing time on postoperative effects in children with partially accommodative esotropia.

PubMed

Jiang, Danni; Han, Dong; Zhang, Jiahuan; Pei, Tianxu; Zhao, Qi

2018-05-01

The aim of this study was to evaluate the influence of the preoperative wearing time on the postoperative effect in children with partially accommodative esotropia.Sixty children with partially accommodative esotropia who visited our hospital were placed in full cycloplegic refraction by using 1% Atropine eye gel and then wore full hyperopic correction glasses. Children were divided into groups A and B according to the preoperative wearing time. The visual acuity, eye position, and results of the synoptophore and Titmus stereoacuity tests were recorded before and half a year after the surgery in each group, and appropriate statistical analyses were conducted.Half a year after the operation, 54 cases achieved orthotropia when wearing full hyperopic correction glasses. One case was overcorrected. Five cases were undercorrected. The results of the synoptophore and Titmus stereoacuity test showed that there was no significant difference between postoperative outcomes for patients who wore glasses for half a year and for 1 year before the operation.For children with partially accommodative esotropia, surgery should be used to correct the eye position after wearing full hyperopic correction glasses for half a year to improve the eye position and binocular vision as early as possible. If the operation cannot be completed after the patient wears full hyperopic correction glasses for half a year due to various subjective and objective factors, a good postoperative effect can be obtained if the patients receive surgery after wearing full hyperopic correction glasses for 1 year.

Wear of two pit and fissure sealants in contact with primary teeth

PubMed Central

Galo, Rodrigo; Contente, Marta Maria Martins Giamatei; Borsatto, Maria Cristina

2014-01-01

Objectives: Wear simulations may provide an indication of the clinical performance of pit-and-fissure sealants when associated with primary teeth as counterbody, restricting the involved variables. The aim of this study was to evaluate wear of dental materials used as pit-and-fissure sealants in contact with primary teeth. Materials and Methods: A resinous sealant (Fluroshield®) and a resin-modified glass ionomer cement (Vitremer®) were selected in a post-plate design, using as counterbody primary tooth pins (4 × 4 × 2 mm) at 3 and 10 N vertical load, 1 Hz frequency, 900 wear cycles in artificial saliva (n = 15). Attrition coefficient values were obtained and the material and primary tooth volumes were analyzed. Data were analyzed statistically by ANOVA and Duncan's test (P < 0.05). Results: Fluroshield® presented the highest attrition coefficient values for the 3 N but these values decreased significantly for the 10 N load. The means for volume loss (3 mm) of the different samples after the wear test were not statistically different for the materials. The volume loss values for the primary teeth were statistically different and there was an increase in volume loss with the increase of the load applied in the wear tests. Conclusions: Differences were also observed with regard to the surface deformation characteristics. The wear rates of primary tooth enamel vary according to the type of material and the load applied during mastication. PMID:24966777

Experimental Evaluation and Optimization of Flank Wear During Turning of AISI 4340 Steel with Coated Carbide Inserts Using Different Cutting Fluids

NASA Astrophysics Data System (ADS)

Lawal, S. A.; Choudhury, I. A.; Nukman, Y.

2015-01-01

The understanding of cutting fluids performance in turning process is very important in order to improve the efficiency of the process. This efficiency can be determined based on certain process parameters such as flank wear, cutting forces developed, temperature developed at the tool chip interface, surface roughness on the work piece, etc. In this study, the objective is to determine the influence of cutting fluids on flank wear during turning of AISI 4340 with coated carbide inserts. The performances of three types of cutting fluids were compared using Taguchi experimental method. The results show that palm kernel oil based cutting fluids performed better than the other two cutting fluids in reducing flank wear. Mathematical models for cutting parameters such as cutting speed, feed rate, depth of cut and cutting fluids were obtained from regression analysis using MINITAB 14 software to predict flank wear. Experiments were conducted based on the optimized values to validate the regression equations for flank wear and 5.82 % error was obtained. The optimal cutting parameters for the flank wear using S/N ratio were 160 m/min of cutting speed (level 1), 0.18 mm/rev of feed (level 1), 1.75 mm of depth of cut (level 2) and 2.97 mm2/s palm kernel oil based cutting fluid (level 3). ANOVA shows cutting speed of 85.36 %; and feed rate 4.81 %) as significant factors.

A Close Cut: A Technical Report of Endovascular Removal of a Penetrating Intravascular Foreign Body after a Lawn Mowing Injury

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tapping, C. R.; Gallo, A.; Silva, R. J. De

2012-12-15

We present a case of endovascular retrieval of a penetrating foreign body that was originally lodged in the mediastinum and then migrated to the hepatic vein. The steel nail entered the thorax and traversed the left lung causing a pneumothorax. The patient underwent a thoracotomy, but the foreign body had migrated from its original mediastinal position. A postsurgical CT showed that the object was below the right hemidiaphragm. Diagnostic venogram demonstrated that the object was in the main hepatic vein. Using a double-snare technique, the object was safely and successfully removed from the hepatic vein via the right common femoralmore » vein.« less

Communication and Gamification in the Web-Based Foreign Language Educational System: Web- Based Foreign Language Educational System

ERIC Educational Resources Information Center

Osipov, Ilya V.; Volinsky, Alex A.; Nikulchev, Evgeny; Prasikova, Anna Y.

2016-01-01

The paper describes development of the educational online web communication platform for teaching and learning foreign languages. The main objective was to develop a web application for teaching foreigners to understand casual fluent speech. The system is based on the time bank principle, allowing users to teach others their native language along…

Integrating Language-and-Culture Teaching: An Investigation of Spanish Teachers' Perceptions of the Objectives of Foreign Language Education

ERIC Educational Resources Information Center

Castro, Paloma; Sercu, Lies; Mendez Garcia, Maria del Carmen

2004-01-01

A recent shift has been noticeable in foreign language education theory. Previously, foreign languages were taught as a linguistic code. This then shifted to teaching that code against the sociocultural background of, primarily, one country in which the foreign language is spoken as a national language. More recently, teaching has reflected on…

Characterization of ferromagnetic or conductive properties of metallic foreign objects embedded within the human body with magnetic iron detector (MID): Screening patients for MRI.

PubMed

Gianesin, Barbara; Zefiro, Daniele; Paparo, Francesco; Caminata, Alessio; Balocco, Manuela; Carrara, Paola; Quintino, Sabrina; Pinto, Valeria; Bacigalupo, Lorenzo; Rollandi, Gian Andrea; Marinelli, Mauro; Forni, Gian Luca

2015-05-01

A preliminary assessment of the MRI-compatibility of metallic object possibly embedded within the patient is required before conducting the MRI examination. The Magnetic Iron Detector (MID) is a highly sensitive susceptometer that uses a weak magnetic field to measure iron overload in the liver. MID might be used to perform a screening procedure for MRI by determining the ferromagnetic/conductive properties of embedded metallic objects. The study was composed by: (i) definition of MID sensitivity threshold; (ii) application of MID in a procedure to characterize the ferromagnetic/conductive properties of metallic foreign objects in 958 patients scheduled for MID examination. The detection threshold for ferromagnetic objects was found to be the equivalent of a piece of wire of length 2 mm and gauge 0.8 mm(2) and, representing purely conductive objects, an aluminum sheet of area 2 × 2 cm(2) . Of 958 patients, 165 had foreign bodies of unknown nature. MID was able to detect those with ferromagnetic and/or conducting properties based on fluctuations in the magnetic and eddy current signals versus control. The high sensitivity of MID makes it suitable for assessing the ferromagnetic/conductive properties of metallic foreign objects embedded within the body of patients scheduled for MRI. © 2015 Wiley Periodicals, Inc.

Percutaneous Retrieval of Misplaced Intravascular Foreign Objects with the Dormia Basket: An Effective Solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheth, Rahul; Someshwar, Vimal; Warawdekar, Gireesh

2007-02-15

Purpose. We report our experience of the retrieval of intravascular foreign body objects by the percutaneous use of the Gemini Dormia basket. Methods. Over a period of 2 years we attempted the percutaneous removal of intravascular foreign bodies in 26 patients. Twenty-six foreign bodies were removed: 8 intravascular stents, 4 embolization coils, 9 guidewires, 1 pacemaker lead, and 4 catheter fragments. The percutaneous retrieval was achieved with a combination of guide catheters and the Gemini Dormia basket. Results. Percutaneous retrieval was successful in 25 of 26 patients (96.2%). It was possible to remove all the intravascular foreign bodies with amore » combination of guide catheters and the Dormia basket. No complication occurred during the procedure, and no long-term complications were registered during the follow-up period, which ranged from 6 months to 32 months (mean 22.4 months overall). Conclusion. Percutaneous retrieval is an effective and safe technique that should be the first choice for removal of an intravascular foreign body.« less

75 FR 81708 - Notice of Decision To Issue Buy American Waivers for Foreign Object Debris (FOD) Detection Equipment

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

... Circular 150/5220-24, Airport Foreign Object Debris (FOD) detection equipment, detailing system... produce sufficient and reasonable amounts of stationary FOD detection systems; the FAA issued a notice in... manufacturing stationary FOD detection systems in the United States: Trex Aviation Systems and QinetiQ. Although...

Communicative, Educational, Pedagogical Objectives and Planning in Russian Language Teaching

ERIC Educational Resources Information Center

Evtyugina, Alla A.; Hasanova, Irina I.; Kotova, Svetlana S.; Sokolova, Anastasia N.; Svetkina, Irina A.

2016-01-01

The relevance of the problem stems from the necessity to distinctly plan educational process and set the goals for successful mastering of Russian language by foreign students in Russian higher educational institutions. The article is aimed at defining the foreign students' objectives for Russian language training, allowing them to get involved…

Double aortic arch presenting with a foreign object in the oesophagus: a case report and imaging diagnosis.

PubMed

Yang, Xiuzhen; Ye, Jingjing; Gao, Zhan

2017-10-01

In this article, we report a rare case of double aortic arch. The case presented initially with a foreign object in the oesophagus. The patient was a 2-year-old boy, who was referred with primary symptoms of tussis (15 days) and emesis (2 days). He had a history of ingesting a coin. Routine chest X-ray indicated a rounded, metal foreign object in the upper oesophagus. A half-Yuan coin was removed by gastroduodenoscopy. Echocardiographic imaging suggested that the patient had double aortic arch, which was subsequently diagnosed by CT angiography with three-dimensional reconstruction. The right subclavian artery arose from the right loop of the double aortic arch. The left subclavian artery as well as left and right common carotid arteries had distinct origins from the left aortic arch. Imaging also indicated atresia of the distal left arch. The patient underwent corrective surgery and made a full recovery. Despite the rarity, double aortic arch should be considered when patients present with a foreign object in the oesophagus. Echocardiography and CT angiography can inform the diagnosis.

Surface Chemistry and Tribology of Copper Surfaces in Carbon Dioxide and Water Vapor Environments

DTIC Science & Technology

2011-02-23

state that the copper brushes in the superconducting homopolar motor experience wear at rates greater than 3X10" wear /distance traveled when biased...positively. It has been found the motor operates best in an atmosphere of carbon dioxide and water vapor. The objective of our research therefore is...possible to prepare different chemical states of the Cu, as those produced in the motor electrodes under positive and negative bias. In situ XAS

Cannon Wear and Erosion Science and Technology Objective Program (STO) 155-mm Projectile Rotating Band/Obturation for Extended Range

DTIC Science & Technology

2015-06-01

loading of the projectile steel against the gun tube with concomitant increased gun tube wear. Chromium Nodules and Thermal Gouging Chromium nodules...40 mm and 80-mm anti-aircraft gun ) and the fact that welded rotating bands in the past were made from ARMCO Inc. iron. Stainless steel was selected...down the gun tube. Nickel rotating band Stainless steel rotating band Figure 12 Redesigned band configurations Based on the results

Impact of Advertising on Tampon Wear-time Practices

PubMed Central

Woeller, Kara E.; Miller, Kenneth W.; Robertson-Smith, Amy L.; Bohman, Lisa C.

2015-01-01

OBJECTIVES (1) To determine whether advertising nighttime tampon use for up to eight hours was understood to be consistent with label recommendations and (2) to determine whether television and print advertising with this message affected tampon wear times in adults and teens. METHODS (1) A comprehension study (online advertising and follow-up questionnaire) among women aged 14–49 years (300 per group) who viewed either the test or a control advertising message; (2) Diary-based surveys of tampon wear times performed prior to (n = 292 adults, 18–49 years, 74 teens, 12–17 years) and after (n = 287 adults, 104 teens) the launch of national advertising. RESULTS Significantly more test message viewers than controls stated tampons should be worn less than or equal to eight hours (93.6% vs. 88.6%, respectively, P = 0.049). A directionally higher percentage of test message viewers said they would use a pad if sleeping longer than eight hours (52% vs. 42% of controls). Among the women who used tampons longer than eight hours when sleeping, 52% reported they would wake up and change compared with 45% of controls. No significant difference between baseline and follow-up diary surveys was found among teens or adults in various measures of tampon wear time (mean wear times; usage intervals from less than two hours to more than 10 hours; percentage of tampons used for more than or equal to eight hours; frequency of wearing at least one tampon more than eight hours). CONCLUSIONS Advertising nighttime tampon wear for up to eight hours effectively communicated label recommendations but did not alter tampon wear times. The informational intervention had limited impact on established habits. PMID:26688668

Wear resistance of polypropylene-SiC composite

NASA Astrophysics Data System (ADS)

Abenojar, J.; Enciso, B.; Martínez, MA; Velasco, F.

2017-05-01

In this work, the wear resistance of thermoplastic composites with a high amount of ceramic is evaluated. Composites made of polypropylene (PP) and silicon carbide (SiC) powder at 50 wt% were used with the final objective of manufacturing ablative materials. This is the first part of a project studying the wear resistance and the mechanical properties of those composites, to be used in applications like habitat industry. In theory, the exposure to high temperature of ablative materials involves the elimination of thermal energy by the sacrifice of surface polymer. In our case, PP will act as a heat sink, up to the reaction temperature (melting or sublimation), where endothermic chemical decomposition into charred material and gaseous products occurs. As the surface is eroded, it is formed a SiC like-foam with improved insulation performance. Composites were produced by extrusion and hot compression. The wear characterization was performed by pin-on-disk test. Wear test was carried out under standard ASTM G99. The parameters were 120 rpm speed, 15 N load, a alumina ball with 6 mm as pin and 1000 m sliding distance. The tracks were also observed by opto-digital microscope.

Nut Cracking Tools Used by Captive Chimpanzees (Pan troglodytes) and Their Comparison with Early Stone Age Percussive Artefacts from Olduvai Gorge.

PubMed

Arroyo, Adrián; Hirata, Satoshi; Matsuzawa, Tetsuro; de la Torre, Ignacio

2016-01-01

We present the results of a series of experiments at the Kumamoto Sanctuary in Japan, in which captive chimpanzees (Pan troglodytes) performed several nut cracking sessions using raw materials from Olduvai Gorge, Tanzania. We examined captive chimpanzee pounding tools using a combination of technological analysis, use-wear distribution, and micro-wear analysis. Our results show specific patterns of use-wear distribution across the active surfaces of pounding tools, which reveal some similarities with traces on archaeological percussive objects from the Early Stone Age, and are consistent with traces on other experimental pounding tools used by modern humans. The approach used in this study may help to stablish a framework with which to interpret archaeological assemblages and improve understanding of use-wear formation processes on pounding tools used by chimpanzees. This study represents the first direct comparison of chimpanzee pounding tools and archaeological material, and thus may contribute to a better understanding of hominin percussive activities.

Characterization of the Micro-Abrasive Wear in Coatings of TaC-HfC/Au for Biomedical Implants

PubMed Central

Guzmán, Pablo; Yate, Luis; Sandoval, Mercy; Caballero, Jose

2017-01-01

The object of this work was the deposition of a Ta-Hf-C thin film with a gold interlayer on stainless steel, via the physical vapor deposition (PVD) technique, in order to evaluate the properties of different systems subjected to micro-abrasive wear phenomena generated by alumina particles in Ringer's solution. The surface characterization was performed using a scanning electron microscope (SEM) and atomic force microscope (AFM). The crystallographic phases exhibited for each coating were obtained by X-ray diffraction (XRD). As a consequence of modifying the composition of Ta-Hf there was evidence of an improvement in the micro-abrasive wear resistance and, for each system, the wear constants that confirm the enhancement of the surface were calculated. Likewise, these surfaces can be bioactive, generating an alternative to improve the biological fixation of the implants, therefore, the coatings of TaC-HfC/Au contribute in the development of the new generation of orthopedic implants. PMID:28773207

Interproximal grooving in the Atapuerca-SH hominid dentitions.

PubMed

Bermúdez de Castro, J M; Arsuaga, J L; Pérez, P J

1997-03-01

The dental sample recovered from the Sima de los Huesos (SH) Middle Pleistocene cave site of the Sierra de Atapuerca (Spain) includes 296 specimens. Interproximal wear grooves have been observed in 20 maxillary and mandibular posterior teeth belonging to at least five of the 32 individuals identified so far in the SH hypodigm. Interproximal grooving affected only the adults, and at an age between 25 and 40 years. The appearance, morphology, and location pattern of the SH wear grooves are similar to those reported in other fossil hominids and in more recent human populations. Two alternative proposals, the toothpicking and the fiber or sinew processing hypotheses, compete for explaining the formation of this anomalous wear. The characteristics observed in the wear grooves of the SH teeth are compatible only with the habitual probing of interdental spaces by means of hard and inflexible objects. Dietary grit may also have contributed to the abrasion of the root walls during the motion of the dental probes.

Nut Cracking Tools Used by Captive Chimpanzees (Pan troglodytes) and Their Comparison with Early Stone Age Percussive Artefacts from Olduvai Gorge

PubMed Central

Arroyo, Adrián; Hirata, Satoshi; Matsuzawa, Tetsuro; de la Torre, Ignacio

2016-01-01

We present the results of a series of experiments at the Kumamoto Sanctuary in Japan, in which captive chimpanzees (Pan troglodytes) performed several nut cracking sessions using raw materials from Olduvai Gorge, Tanzania. We examined captive chimpanzee pounding tools using a combination of technological analysis, use-wear distribution, and micro-wear analysis. Our results show specific patterns of use-wear distribution across the active surfaces of pounding tools, which reveal some similarities with traces on archaeological percussive objects from the Early Stone Age, and are consistent with traces on other experimental pounding tools used by modern humans. The approach used in this study may help to stablish a framework with which to interpret archaeological assemblages and improve understanding of use-wear formation processes on pounding tools used by chimpanzees. This study represents the first direct comparison of chimpanzee pounding tools and archaeological material, and thus may contribute to a better understanding of hominin percussive activities. PMID:27870877

High wear resistance of femoral components coated with titanium nitride: a retrieval analysis.

PubMed

Fabry, Christian; Zietz, Carmen; Baumann, Axel; Ehall, Reinhard; Bader, Rainer

2017-05-20

The objective of this study was to evaluate the in vivo wear resistance of cobalt-chromium femoral components coated with titanium nitride (TiN). Our null hypothesis was that the surface damage and the thickness of the TiN coating do not correlate with the time in vivo. Twenty-five TiN-coated bicondylar femoral retrievals with a mean implantation period of 30.7 ± 11.7 months were subjected to an objective surface damage analysis with a semi-quantitative assessment method. A visual examination of scratches, indentations, notches and coating breakthroughs of the surfaces was performed. The roughness and the coating thickness of the TiN coating were evaluated in the main articulation regions. Narrow scratches and indentations in the range of low flexion angles on the retrieval surfaces were the most common modes of damage. There was no evidence of delamination on the articulation surface but rather at the bottom of isolated severe indentations or notches. An analysis of three retrievals revealed a coating breakthrough in the patellofemoral joint region, resulting from patella maltracking and a dislocation. The arithmetical mean roughness of the TiN surface slightly increased with the implantation period. In contrast, the maximum peak height of the roughness profile was reduced at the condyles of the retrieved components in comparison with new, unused surfaces. No significant association between the coating thickness and implantation period was determined. Moreover, the measured values were retained in the range of the initial coating thickness even after several years of in vivo service. As was demonstrated by the results of this study, the surface damage to the TiN coating did not deteriorate with the implantation period. The calculated damage scores and the measured coating thickness in particular both confirmed that the TiN coating provides low wear rates. Our findings support the use of wear-resistant TiN-coated components in total knee arthroplasty with the objective of reducing the risk of aseptic loosening. However, in terms of TiN-coated femoral components, particular attention should be paid to a correct patellar tracking in order to avoid wear propagation at the implant.

Objective and subjective responses in patients refitted to daily-wear silicone hydrogel contact lenses.

PubMed

Dumbleton, Kathryn; Keir, Nancy; Moezzi, Amir; Feng, Yunwei; Jones, Lyndon; Fonn, Desmond

2006-10-01

Silicone hydrogel (SiH) lenses offer many physiological advantages for daily wear (DW) in addition to the continuous-wear modality for which they were originally developed. The purpose of this study was to investigate the clinical performance and physiological responses in a group of successful long-term wearers of conventional hydrogel lenses when refitted with DW SiH contact lenses. Eighty-seven successful soft lens wearers (8.4+/-4.7 years of prior lens wear) participated in this study. Bulbar and limbal hyperemia were subjectively graded and digitally photographed for subsequent masked objective evaluation. Subjective symptoms were scored using visual analog scales. In addition, refractive error, corneal curvature, and corneal thickness were measured. All subjects were refitted with Focus Night & Day (lotrafilcon A) SiH lenses; however, to reduce the potential for bias, they were informed that they were being randomly assigned to wear either low oxygen permeability (Dk) lenses or high Dk SiH lenses and were "masked" as to their lens assignment. Subjects returned after 1 week, 1 month, and 2 months of DW, at which time all gradings, photographs, and measurements were repeated. End-of-day subjective symptoms were also graded periodically during the study. Ninety-three percent of subjects were successfully refitted. Both objective and subjective evaluations showed that bulbar and limbal hyperemia decreased significantly in all quadrants during the study (p<0.001), particularly for those subjects with greater baseline hyperemia (p<0.001). Subjects reported a concurrent reduction in end-of-day dryness and improved end-of-day comfort compared with their habitual lenses (p<0.001). No significant changes in refractive error, tarsal papillary response, corneal curvature, or corneal thickness were found during the study. Hyperemia in contact lens wearers may be attributed to a number of factors, including hypoxia. Refitting existing low Dk lens wearers with SiH lenses on a DW basis can result in a decrease in hyperemia, which may be significant for some subjects and also results in improvements in symptoms of dryness and discomfort.

Reduction of metallosis in hip implant using thin film coating

NASA Astrophysics Data System (ADS)

Rajeshshyam, R.; Chockalingam, K.; Gayathri, V.; Prakash, T.

2018-04-01

Hip implant finds its emerging attraction due to it continuous demand over the years. The hip implants (femoral head) and acetabulum cup) mainly fabricated by metals such as stainless steel, cobalt chrome and titanium alloys, other than that ceramics and polyethylene have been used. The metal-on-metal hip implant was found to be best implant material for most of the surgeons due to its high surface finish, low wear rate and low chance of dislocation from its position after implanting. Where in metal based hip implant shows less wear rate of 0.01mm3/year. Metal-on-metal implant finds its advantage over other materials both in its mechanical and physical stability against human load. In M-O-M Cobalt- chromium alloys induce metal allergy. The metal allergy (particulate debris) that is generated by wear, fretting, fragmentation and which is unavoidable when a prosthesis is implanted, can induce an inflammatory reaction in some circumstances. The objectives of this research to evaluate thin film coating with Nano particle additives to reduce the wear leads to regarding metal ion release. Experimental results reveals that thin film Sol-Gel coating with 4wt. % of specimen reduced the cobalt and chromium ion release and reduces the wear rate. Wear rate reduced by 98% for 4wt. % graphene in 20N and 95% for 4wt. % graphene in 10N.

The Effect of Wearing White Coats on Patients' Appreciation of Physician Communication during Postpartum Rounds: A Randomized Controlled Trial.

PubMed

La Rosa, Mauricio; Spencer, Nicholas; Abdelwahab, Mahmoud; Zambrano, Gabriela; Saoud, Fawzi; Jelliffe, Katherine; Olson, Gayle; Munn, Mary; Saade, George R; Costantine, Maged

2018-06-08

 Wearing a white coat (WC) has been associated with risk of colonization and transmission of resistant pathogens. Also, studies have shown that physicians' attire in general affects patients' confidence in their physician and the patient-physician relationship. Our objective is to evaluate the hypothesis that not wearing a WC during physician postpartum rounds does not affect patient-physician communication scores.  This is an unblinded, randomized, parallel arms, controlled trial of postpartum women at a single university hospital. Women were randomly assigned to having their postpartum physicians' team wear a WC or not (no-WC) during rounds. Our primary outcome was "patient-physician communication" score. Univariable and multivariable analysis were used where appropriate.  One hundred and seventy-eight patients were enrolled (87 in WC and 91 in no-WC groups). Note that 40.4% of patients did not remember whether the physicians wore a WC or not. There was no difference in the primary outcome ( p  = 0.64) even after adjusting for possible confounders.  Not wearing a WC during postpartum rounds did not affect the patient-physician communication or patient satisfaction scores. In the setting of prior reports showing a risk of WC pathogen transmission between patients, our findings cannot support the routine wearing of WCs during postpartum rounds. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Optimization of tribological performance of SiC embedded composite coating via Taguchi analysis approach

NASA Astrophysics Data System (ADS)

Maleque, M. A.; Bello, K. A.; Adebisi, A. A.; Akma, N.

2017-03-01

Tungsten inert gas (TIG) torch is one of the most recently used heat source for surface modification of engineering parts, giving similar results to the more expensive high power laser technique. In this study, ceramic-based embedded composite coating has been produced by precoated silicon carbide (SiC) powders on the AISI 4340 low alloy steel substrate using TIG welding torch process. A design of experiment based on Taguchi approach has been adopted to optimize the TIG cladding process parameters. The L9 orthogonal array and the signal-to-noise was used to study the effect of TIG welding parameters such as arc current, travelling speed, welding voltage and argon flow rate on tribological response behaviour (wear rate, surface roughness and wear track width). The objective of the study was to identify optimal design parameter that significantly minimizes each of the surface quality characteristics. The analysis of the experimental results revealed that the argon flow rate was found to be the most influential factor contributing to the minimum wear and surface roughness of the modified coating surface. On the other hand, the key factor in reducing wear scar is the welding voltage. Finally, a convenient and economical Taguchi approach used in this study was efficient to find out optimal factor settings for obtaining minimum wear rate, wear scar and surface roughness responses in TIG-coated surfaces.

Indiana University's Foreign Language Dialog, Volume 14, Number 1: The President's Commission.

ERIC Educational Resources Information Center

Strasheim, Lorraine A.

Excerpts from the first "Bulletin" of the President's Commission on Foreign Language and International Studies and an outline of the coordinator's presentation to the Chicago hearing are presented. The objectives of the commission include recommending means for directing public attention to the importance of foreign language and…

Formal and Informal Experiential Realms in German as a Foreign Language: A Preliminary Investigation

ERIC Educational Resources Information Center

Moyer, Alene

2005-01-01

In this study of German as a foreign language, formal classroom experience is compared with informal use of German outside the classroom focusing on three syntactic features: main clause word order (subject-verb-object, or SVO), topicalization (subject-verb inversion), and subordinate word order (subject-object-verb, or SOV). T tests and…

The Value of Homemade Phantoms for Training Veterinary Students in the Ultrasonographic Detection of Radiolucent Foreign Bodies

ERIC Educational Resources Information Center

Mariano Beraldo, Carolina; Rondon Lopes, Érika; Hage, Raduan; Hage, Maria Cristina F. N. S.

2017-01-01

Ingested or penetrating foreign bodies are common in veterinary medicine. When they are radiolucent, these objects become a diagnostic challenge, but they can be investigated sonographically. However, successful object identification depends on the skill of the sonographer. Considering that these cases appear randomly during hospital routines, it…

An objective and cross-sectional examination of sun-safe behaviours in New South Wales primary schools.

PubMed

Dudley, Dean A; Cotton, Wayne G; Winslade, Matthew J; Wright, Bradley J; Jackson, Kirsten S; Brown, Alexandra M; Rock, Vanessa

2017-01-05

Previous evaluations have supported the link between sun protection policies and improved sun protection behaviours. However these evaluations have relied on self-reported data. A cross-sectional design as part of an ongoing 18-month cluster-controlled trial in primary schools (n = 20) was used. Researchers conducted direct observations to record students' hat use and teachers' use of sun protective measures during recess and lunch. Researchers also recorded the volume of sunscreen consumed in each school. Only 60% of primary school children wear a sun-safe hat during their breaks when observed using objective measures. Weak correlations were observed between the wearing of a sun-safe hat and a school's socio-economic status (r = 0.26). All other independent variables measured had only very weak correlations (r < 0.19) with sun-safe hat wearing behaviour of students. Sunscreen consumption by school students during the school day is negligible. A large percentage of NSW primary schools in this study wear sun-safe hats during the school day but this is well below what has been reported in previous national surveys. Given the finite resources of schools and the correlation, though small, with SES status for these behaviours, it behoves researchers to investigate low-cost solutions to these problems. Further qualitative data will also be needed to inform the enablers and barriers for sun-safe behaviour interventions to be adopted in NSW primary schools.

Esophageal foreign bodies in adults with different durations of time from ingestion to effective treatment

PubMed Central

Zhang, Xiaowen; Jiang, Yan; Fu, Tao; Zhang, Xiaoheng; Tu, Chunmei

2017-01-01

Objective This study was performed to identify the differences in clinical characteristics, operative methods, complications, and postoperative hospitalization stays for adults with esophageal foreign bodies with different durations of time from ingestion to effective treatment. Methods We retrospectively reviewed the medical records of 221 patients with a diagnosis of a foreign body in the esophagus, confirmed by rigid esophagoscopy, flexible esophagoscopy, or surgery. The differences between the two groups (Group A, ≤24 hours from ingestion to effective treatment; Group B, >24 hours from ingestion to effective treatment) were analyzed. Results Sharp foreign bodies comprised the majority of objects in the two groups, including jujube pits, bones (excluding fish bones), fish bones, dentures, and seafood shells. Foreign bodies located in the upper esophagus were more commonly observed in Group A than B. Significant differences were observed in the complication rate and length of postoperative hospitalization stays. Adults with esophageal foreign bodies had a high complication rate. Conclusions Rigid esophagoscopy can be used to remove sharp and bulky foreign bodies if more effective methods are unavailable. Effective treatment within 24 hours resulted in fewer complications and shorter postoperative hospitalization stays. PMID:28606025

Complications in children from foreign bodies in the airway.

PubMed

Rodríguez, Hugo; Cuestas, Giselle; Botto, Hugo; Nieto, Mary; Cocciaglia, Alejandro; Passali, Desiderio; Gregori, Dario

2016-01-01

Foreign body aspiration in childhood is a common and potentially serious problem. Complications may be the result of the aspiration episode itself, delayed diagnosis or treatment. We describe our experience in a paediatric hospital in Argentina. We retrospectively evaluated 56 patients with complications due to foreign body aspiration recorded in the Susy Safe Project between January 2010 and November 2013. The clinical variables analysed were sex, age at time of aspiration, foreign body location and type, time elapsed from the event until object removal, extraction technique, complications, need for hospitalisation and circumstances of the event. 58.9% of the cases described occurred in males, with high presence of adults (76.8%) at the time of aspiration. The incidence was slightly higher in children older than 3 years. In 37 cases (66.1%), the foreign body was located in bronchus; sunflower seeds and ballpoint caps were the most common foreign objects. Only in 10 cases (17.9%) was the object extracted within 24h of the event. The most common complications were pneumonia (18 cases), granuloma (15 cases) and mucosal erosion (9 cases). Hospitalisation was necessary for 41 patients. Early diagnosis and immediate control through specialised teams are essential to ensure proper treatment, usually endoscopic, without risk of complications. Copyright © 2014 Elsevier España, S.L.U. and Sociedad Española de Otorrinolaringología y Patología Cérvico-Facial. All rights reserved.

Foreign bodies in tracheobronchial tree in children: a review of cases over a twenty-year period.

PubMed

Yeh, L C; Li, H Y; Huang, T S

1998-03-01

Foreign body inhalation into the tracheobronchial tree of children is rather rare but serious problem. It may be hazardous and even cause fatal sequelae in the children if misdiagnosed and not managed promptly. We retrospectively reviewed the records of 81 patients with foreign bodies inhaled into the larynx, trachea and bronchi. The children were all treated during the 20-year period from July 1976 through June 1996 at Chang Gung Memorial Hospital. Of these patients, 82% were 36 months of age or younger. The male to female ratio was 3:1. All of the patients initially received flexible fiberoptic bronchoscopy to identify the foreign objects. The foreign bodies were removed by jet ventilation bronchoscopy with apneic techniques under general anesthesia. Peanuts were found to be the most common causative foreign body agent which occurred in 53 instances (65%). The most common manifestation was coughing, with subsequent dyspnea and audible wheezing. The foreign bodies were lodged in the left bronchus more than in the right. The most obvious radiologic evidence observed in aspirated children were emphysematous changes at same side of the foreign bodies caused by "expansile check-valve" phenomenon. Four patients showed radio-opaque objects on chest roentgenograms. Six patients required second extraction procedures due to the retained foreign bodies. Neither serious complications nor deaths occurred in these patients due to the foreign body inhalation. Early diagnosis and management is essential in children with foreign bodies in the airways to prevent morbidity or death. Small materials or food bits should be kept far away from young child.

Comparison of Primary School Foreign Language Curricula of Turkey, Germany and the Netherlands

ERIC Educational Resources Information Center

Aslan, Yasin

2016-01-01

Foreign language education at early ages involves a broad spectrum of communication skills using communication, culture, connections, comparisons and community. The aim of this study is to compare the primary foreign language curricula of Turkey, Germany and the Netherlands in terms of objectives, content, teaching processes and evaluation…

10 CFR 603.875 - Foreign access to technology and U.S. competitiveness provisions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Foreign access to technology and U.S. competitiveness provisions. 603.875 Section 603.875 Energy DEPARTMENT OF ENERGY (CONTINUED) ASSISTANCE REGULATIONS TECHNOLOGY... Foreign access to technology and U.S. competitiveness provisions. (a) Consistent with the objective of...

10 CFR 603.875 - Foreign access to technology and U.S. competitiveness provisions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Foreign access to technology and U.S. competitiveness provisions. 603.875 Section 603.875 Energy DEPARTMENT OF ENERGY (CONTINUED) ASSISTANCE REGULATIONS TECHNOLOGY... Foreign access to technology and U.S. competitiveness provisions. (a) Consistent with the objective of...

10 CFR 603.875 - Foreign access to technology and U.S. competitiveness provisions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 4 2013-01-01 2013-01-01 false Foreign access to technology and U.S. competitiveness provisions. 603.875 Section 603.875 Energy DEPARTMENT OF ENERGY (CONTINUED) ASSISTANCE REGULATIONS TECHNOLOGY... Foreign access to technology and U.S. competitiveness provisions. (a) Consistent with the objective of...

Integrating Intercultural and Communicative Objectives in the Foreign Language Class: A Proposal for the Integration of Two Models

ERIC Educational Resources Information Center

Borghetti, Claudia

2013-01-01

The "intercultural turn" of the 1990s brought about the introduction of the terms "Foreign Language Education" and "Intercultural Foreign Language Education" (IFLE) in place of "language teaching". These terms broaden the aims of language education to include students' intercultural competence (IC),…

10 CFR 603.875 - Foreign access to technology and U.S. competitiveness provisions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Foreign access to technology and U.S. competitiveness provisions. 603.875 Section 603.875 Energy DEPARTMENT OF ENERGY (CONTINUED) ASSISTANCE REGULATIONS TECHNOLOGY... Foreign access to technology and U.S. competitiveness provisions. (a) Consistent with the objective of...

DOD/COCOM Water Security Program Strategy Document

DTIC Science & Technology

2011-04-22

in alignment with USG foreign policy objectives? The following discussion and appendices provide a framework to facilitate this process for DOD...USG foreign policy objectives? The following discussion and appendices provide a framework to facilitate this process for DOD. DOD/COCOM Water...technology, etc. Because water resources often cross political boundaries on a regional scale, focusing water scarcity initiatives on this level

Professional Training of Future Teachers in Foreign Countries in Terms of Intercultural Interaction of Educational Space Objects

ERIC Educational Resources Information Center

Desyatov, Tymofiy

2015-01-01

The problem of professional training of teachers in foreign countries in terms of intercultural interaction of educational space objects has been studied in the paper. It has been stated that the current stage of human civilization development which is defined as the transition to a knowledge society, is characterized by qualitatively new…

Multi-User Domain Object Oriented (MOO) as a High School Procedure for Foreign Language Acquisition.

ERIC Educational Resources Information Center

Backer, James A.

Foreign language students experience added difficulty when they are isolated from native speakers and from the culture of the target language. It has been posited that MOO (Multi-User Domain Object Oriented) may help overcome the geographical isolation of these students. MOOs are Internet-based virtual worlds in which people from all over the real…

Removal of foreign bodies in the upper gastrointestinal tract in adults: European Society of Gastrointestinal Endoscopy (ESGE) Clinical Guideline.

PubMed

Birk, Michael; Bauerfeind, Peter; Deprez, Pierre H; Häfner, Michael; Hartmann, Dirk; Hassan, Cesare; Hucl, Tomas; Lesur, Gilles; Aabakken, Lars; Meining, Alexander

2016-05-01

This Guideline is an official statement of the European Society of Gastrointestinal Endoscopy (ESGE). It addresses the removal of foreign bodies in the upper gastrointestinal tract in adults. Recommendations Nonendoscopic measures 1 ESGE recommends diagnostic evaluation based on the patient's history and symptoms. ESGE recommends a physical examination focused on the patient's general condition and to assess signs of any complications (strong recommendation, low quality evidence). 2 ESGE does not recommend radiological evaluation for patients with nonbony food bolus impaction without complications. We recommend plain radiography to assess the presence, location, size, configuration, and number of ingested foreign bodies if ingestion of radiopaque objects is suspected or type of object is unknown (strong recommendation, low quality evidence). 3 ESGE recommends computed tomography (CT) scan in all patients with suspected perforation or other complication that may require surgery (strong recommendation, low quality evidence). 4 ESGE does not recommend barium swallow, because of the risk of aspiration and worsening of the endoscopic visualization (strong recommendation, low quality evidence). 5 ESGE recommends clinical observation without the need for endoscopic removal for management of asymptomatic patients with ingestion of blunt and small objects (except batteries and magnets). If feasible, outpatient management is appropriate (strong recommendation, low quality evidence). 6 ESGE recommends close observation in asymptomatic individuals who have concealed packets of drugs by swallowing ("body packing"). We recommend against endoscopic retrieval. We recommend surgical referral in cases of suspected packet rupture, failure of packets to progress, or intestinal obstruction (strong recommendation, low quality evidence). Endoscopic measures 7 ESGE recommends emergent (preferably within 2 hours, but at the latest within 6 hours) therapeutic esophagogastroduodenoscopy for foreign bodies inducing complete esophageal obstruction, and for sharp-pointed objects or batteries in the esophagus. We recommend urgent (within 24 hours) therapeutic esophagogastroduodenoscopy for other esophageal foreign bodies without complete obstruction (strong recommendation, low quality evidence). 8 ESGE suggests treatment of food bolus impaction in the esophagus by gently pushing the bolus into the stomach. If this procedure is not successful, retrieval should be considered (weak recommendation, low quality evidence). The effectiveness of medical treatment of esophageal food bolus impaction is debated. It is therefore recommended, that medical treatment should not delay endoscopy (strong recommendation, low quality evidence). 9 In cases of food bolus impaction, ESGE recommends a diagnostic work-up for potential underlying disease, including histological evaluation, in addition to therapeutic endoscopy (strong recommendation, low quality evidence). 10 ESGE recommends urgent (within 24 hours) therapeutic esophagogastroduodenoscopy for foreign bodies in the stomach such as sharp-pointed objects, magnets, batteries and large/long objects. We suggest nonurgent (within 72 hours) therapeutic esophagogastroduodenoscopy for medium-sized blunt foreign bodies in the stomach (strong recommendation, low quality evidence). 11 ESGE recommends the use of a protective device in order to avoid esophagogastric/pharyngeal damage and aspiration during endoscopic extraction of sharp-pointed foreign bodies. Endotracheal intubation should be considered in the case of high risk of aspiration (strong recommendation, low quality evidence). 12 ESGE suggests the use of suitable extraction devices according to the type and location of the ingested foreign body (weak recommendation, low quality evidence). 13 After successful and uncomplicated endoscopic removal of ingested foreign bodies, ESGE suggests that the patient may be discharged. If foreign bodies are not or cannot be removed, a case-by-case approach depending on the size and type of the foreign body is suggested (weak recommendation, low quality evidence). © Georg Thieme Verlag KG Stuttgart · New York.

Atelectasis

MedlinePlus

... a possible complication of other respiratory problems, including cystic fibrosis, inhaled foreign objects, lung tumors, fluid in the ... plugs also are common in children, people with cystic fibrosis and during severe asthma attacks. Foreign body. Atelectasis ...

Mucins in contact lens wear and dry eye conditions.

PubMed

Ramamoorthy, Padmapriya; Nichols, Jason J

2008-08-01

Ocular mucins are thought to play integral roles in ocular surface lubrication, anchoring of the aqueous, stabilizing the lipid components of the tear film, eliminating foreign bodies and pathogens, and with potential involvement in cell cycle mediation and apoptotic activity of ocular surface epithelia. Ocular mucins are of secreted and membrane-associated types. Secreted mucins may be of large gel-forming type or small soluble mucins (e.g., MUC5AC and MUC7). Membrane-associated mucins such as MUCs 1 and 4 are a major component of the glycocalyx. They are thought to render structural support to the microplicae and mediate epithelial cell cycle and apoptotic activity. The alterations in ocular mucins with contact lens wear are unclear. Recent work shows mucin expression may be up-regulated during the early years of contact lens wear, and with long-term lens wear, mucin expression may return to normal levels or sub-normal levels, although this is not well understood. Further, the polar nature of mucins may be associated with their affinity for contact lens surfaces making them a component of contact lens deposition. This has potential implications in the wettability and tolerability of contact lenses, and may be impacted by surface coatings, polymer characteristics, or care solutions. Conjunctival mucin gene expression and secretion may be deficient in several ocular surface disorders associated with dry eye. Deficiency and alterations in glycosylation characteristics of MUC5AC and MUC2 have been reported in both Sjögren and non-Sjögren dry eye types. Decreased binding of the membrane-associated mucin MUC16 to the conjunctival epithelium has been reported in Sjögren dry eye while MUC1 alterations have been reported in Sjögren and non-Sjögren dry eye states. In view of the mucin involvement in dry eye conditions, stimulation of mucus secretion pathways may hold promise in the pharmaceutical treatment of dry eye.

Vapor-delivered lubrication of steel-steel and steel-ceramic systems

NASA Astrophysics Data System (ADS)

Li, H.; Klaus, E. E.; Duda, J. L.

1993-04-01

Heavy-duty natural gas engines run hot and relatively dry. This provides lubricant and lubrication problems in the piston ring-cylinder and valve areas. A potential materials solution to this problem is the use of ceramic bearing surfaces. The objective of the project was the investigation of the wear characteristics and surface interactions of lubricants on ceramic bearing surfaces and to compare these results with the behavior of the same lubricants on steel surfaces. The temperature range of interest in these comparisons is 200 to 370 C using a four-ball wear tester.

Technology developments for a compound cycle engine

NASA Technical Reports Server (NTRS)

Bobula, George A.; Wintucky, William T.; Castor, J. G.

1988-01-01

The Compound Cycle Engine (CCE) is a highly turbocharged, power compounded power plant which combines the light weight pressure rise capability of a gas turbine with the high efficiency of a diesel. When optimized for a rotorcraft, the CCE will reduce fuel burned for a typical 2 hour (plus 30 min reserve) mission by 30 to 40 percent when compared to a conventional advanced technology gas turbine. The CCE can provide a 50 percent increase in range-payload product on this mission. Results of recent activities in a program to establish the technology base for a CCE are presented. The objective of this program is to research and develop those critical technologies which are necessary for the demonstration of a multicylinder diesel core in the early 1990s. A major accomplishment was the initial screening and identification of a lubricant which has potential for meeting the material wear rate limits of the application. An in-situ wear measurement system also was developed to provide accurate, readily obtainable, real time measurements of ring and liner wear. Wear data, from early single cylinder engine tests, are presented to show correlation of the in-situ measurements and the system's utility in determining parametric wear trends. A plan to demonstrate a compound cycle engine by the mid 1990s is included.

Viet Nam’s mandatory motorcycle helmet law and its impact on children

PubMed Central

Pervin, Aaron; Sidik, Mirjam; McKinley, Tyler; Tu, Nguyen Thi Hong; Nam, Nguyen Phuong

2009-01-01

Abstract Objective To measure the use of motorcycle helmets in children and to determine the reasons why children wear helmets less often than adults. Methods The frequency of helmet wearing among adults and children was ascertained by trained roadside observers, and randomized road user surveys were completed in four major centres in Viet Nam: Hanoi, Ho Chi Minh City, Can Tho and Da Nang. Survey data on key questions were cross tabulated, and χ² was calculated for significant differences between parents and non-parents (0.05). Findings The frequency of helmet use in the four study locations ranged from 90–99% among adults, from 15–53% among children ≤ 7 years of age, and from 38–53% among children > 7 but ≤ 14. Of the parents surveyed, 67% said the fear of neck injury was the most important reason their children did not wear a helmet. Conclusion Children wear motorcycle helmets much less often than adults. Legislation to penalize adults whose children do not wear motorcycle helmets has been proposed in Viet Nam. Furthermore, ongoing advocacy and social marketing efforts are being made to disseminate information about the safety benefits of helmets to combat erroneous public perceptions. PMID:19551255

Community football players' attitudes towards protective equipment—a pre-season measure

PubMed Central

Braham, R; Finch, C; McIntosh, A; McCrory, P

2004-01-01

Background: The Australian football injury prevention project (AFIPP) was a randomised controlled trial examining the effects of protective equipment on injury rates in Australian Football. Objective: To present the results of the AFIPP baseline survey of community football players' attitudes towards protective equipment. Methods: Teams of players were recruited from the largest community football league in Victoria, Australia, during the 2001 playing season; 301 players were enrolled in the study and all were surveyed before the season began about their attitudes towards protective headgear and mouthguards. Results: Almost three quarters of the players (73.6%) reported wearing mouthguards during the previous playing season (year 2000) compared with only 2.1% wearing headgear. The most common reasons for not wearing headgear and mouthguards (in non-users) were: "I don't like wearing it" (headgear: 44.8%; mouthguards: 30.6%), and "It is too uncomfortable" (headgear: 40.7%; mouthguards: 45.8%). Conclusions: The higher mouthguard usage reflects the favourable attitudes towards mouthguards by Australian football players generally. Similarly, the low headgear usage reflects the low acceptance of this form of protection in this sport. Further research should be directed towards establishing the reasons why players seem to believe that headgear plays a role in injury prevention yet few wear it. PMID:15273177

New methodology for fast prediction of wheel wear evolution

NASA Astrophysics Data System (ADS)

Apezetxea, I. S.; Perez, X.; Casanueva, C.; Alonso, A.

2017-07-01

In railway applications wear prediction in the wheel-rail interface is a fundamental matter in order to study problems such as wheel lifespan and the evolution of vehicle dynamic characteristic with time. However, one of the principal drawbacks of the existing methodologies for calculating the wear evolution is the computational cost. This paper proposes a new wear prediction methodology with a reduced computational cost. This methodology is based on two main steps: the first one is the substitution of the calculations over the whole network by the calculation of the contact conditions in certain characteristic point from whose result the wheel wear evolution can be inferred. The second one is the substitution of the dynamic calculation (time integration calculations) by the quasi-static calculation (the solution of the quasi-static situation of a vehicle at a certain point which is the same that neglecting the acceleration terms in the dynamic equations). These simplifications allow a significant reduction of computational cost to be obtained while maintaining an acceptable level of accuracy (error order of 5-10%). Several case studies are analysed along the paper with the objective of assessing the proposed methodology. The results obtained in the case studies allow concluding that the proposed methodology is valid for an arbitrary vehicle running through an arbitrary track layout.

Aspects of ultra-high-precision diamond machining of RSA 443 optical aluminium

NASA Astrophysics Data System (ADS)

Mkoko, Z.; Abou-El-Hossein, K.

2015-08-01

Optical aluminium alloys such as 6061-T6 are traditionally used in ultra-high precision manufacturing for making optical mirrors for aerospace and other applications. However, the optics industry has recently witnessed the development of more advanced optical aluminium grades that are capable of addressing some of the issues encountered when turning with single-point natural monocrystalline diamond cutters. The advent of rapidly solidified aluminium (RSA) grades has generally opened up new possibilities for ultra-high precision manufacturing of optical components. In this study, experiments were conducted with single-point diamond cutters on rapidly solidified aluminium RSA 443 material. The objective of this study is to observe the effects of depth of cut and feed rate at a fixed rotational speed on the tool wear rate and resulting surface roughness of diamond turned specimens. This is done to gain further understanding of the rate of wear on the diamond cutters versus the surface texture generated on the RSA 443 material. The diamond machining experiments yielded machined surfaces which are less reflective but with consistent surface roughness values. Cutting tools were observed for wear through scanning microscopy; relatively low wear pattern was evident on the diamond tool edge. The highest tool wear were obtained at higher depth of cut and increased feed rate.

Sliding Seal Materials for Adiabatic Engines, Phase 2

NASA Technical Reports Server (NTRS)

Lankford, J.; Wei, W.

1986-01-01

An essential task in the development of the heavy-duty adiabatic diesel engine is identification and improvements of reliable, low-friction piston seal materials. In the present study, the sliding friction coefficients and wear rates of promising carbide, oxide, and nitride materials were measured under temperature, environmental, velocity, and loading conditions that are representative of the adiabatic engine environment. In addition, silicon nitride and partially stabilized zirconia disks were ion implanted with TiNi, Ni, Co, and Cr, and subsequently run against carbide pins, with the objective of producing reduced friction via solid lubrication at elevated temperature. In order to provide guidance needed to improve materials for this application, the program stressed fundamental understanding of the mechanisms involved in friction and wear. Electron microscopy was used to elucidate the micromechanisms of wear following wear testing, and Auger electron spectroscopy was used to evaluate interface/environment interactions which seemed to be important in the friction and wear process. Unmodified ceramic sliding couples were characterized at all temperatures by friction coefficients of 0.24 and above. The coefficient at 800 C in an oxidizing environment was reduced to below 0.1, for certain material combinations, by the ion implanation of TiNi or Co. This beneficial effect was found to derive from lubricious Ti, Ni, and Co oxides.

Localization and Retrieval of an Eyelid Metallic Foreign Body With an Oscillating Magnet and High-Resolution Ultrasonography.

PubMed

Yoo, Sylvia H; Rootman, Dan B; Goh, Alice; Savar, Aaron; Goldberg, Robert A

2016-01-01

A patient was found to have a metallic foreign body in the left anterior orbit on CT imaging, but the foreign body was not evident on clinical examination. On high-resolution ultrasonography, an object was identified in the left upper eyelid; however, the typical shadow with metallic foreign bodies was not seen. A high-power oscillating magnet was then applied to the eyelid, which revealed a subcutaneous metallic foreign body in the left upper eyelid. When used in conjunction, the high-resolution ultrasound and oscillating magnet successfully localized and facilitated retrieval of the metallic foreign body from the left upper eyelid.

Dental evidence for wild tuber processing among Titicaca Basin foragers 7000 ybp.

PubMed

Watson, James T; Haas, Randall

2017-09-01

The objective of this work is to characterize dental wear in a skeletal sample dating to the Middle/Late Archaic period transition (8,000-6,700 cal. B.P.) from the Lake Titicaca Basin, Peru to better define subsistence behaviors of foragers prior to incipient sedentism and food production. The dental sample consists of 251 teeth from 11 individuals recovered from the site of Soro Mik'aya Patjxa (SMP), the earliest securely dated burial assemblage in the Lake Titicaca Basin and the only burial assemblage in the region from an unequivocal forager context. Occlusal surface wear was quantified according to Smith (1984) and Scott (1979a) to characterize diversity within the site and to facilitate comparison with other foraging groups worldwide. General linear modeling was used to assess observation error and principal axis analysis was used to compare molar wear rates and angles. Teeth were also examined for caries and specialized wear. Occlusal surface attrition is generally heavy across the dental arcade and tends to be flat among posterior teeth. Only one carious lesion was observed. Five of the 11 individuals exhibit lingual surface attrition of the maxillary anterior teeth (LSAMAT). Tooth wear rates, molar wear plane, and caries rates are consistent with terrestrial foraging and a diverse diet. The presence of LSAMAT indicates tuber processing. The results therefore contribute critical new data toward our understanding of forager diet in the Altiplano prior to plant and animal domestication in the south-central Andes. © 2017 Wiley Periodicals, Inc.

[Foreign bodies aspiration in pediatrics. 15-year experience. Analysis of 337 cases].

PubMed

Aguirre Vázquez, I R; Blanco Rodríguez, G; Penchyna Grub, J; Teyssier Morales, G; Serrano Salas, A L

2013-01-01

Foreign body aspiration is a pediatric urgency that occurs primarily between 1 and 3 years old. The aim of this paper is to present the symptomatology, clinical and radiological findings, and the therapeutic used in our hospital with patients with foreign body aspiration diagnosis from 1995 until 2011. Patient's age was between 0 and 16 years old. We included 337 patients; where males predominate (205). The medium age was 23 months. The most frequent foreign bodies founded were seeds (192) in 57% and metallic objects in 18.3%. Cough (74.5%), dyspnea (70%), cyanosis (42.4%) and stridor (26%), were the main symptoms. Right bronchus was the most frequent localization (37.7%). In 21% of the patients the reference diagnostic was wrong due to treating it as a respiratory infection. All foreign bodies were extracted by rigid bronchoscopy. No deaths were reported in any proceeding. In our experience, infants are the most affected group, and the primordial symptoms are cough and dyspnea. Organic objects had the highest prevalence of aspiration.

Exploring Languages and Cultures--An Exploratory Foreign Language Course. A Guide for Teachers.

ERIC Educational Resources Information Center

Milwaukee Public Schools, WI. Div. of Curriculum and Instruction.

A working guide for teachers in planning and teaching an exploratory course in foreign language and culture presents the basic course structure for nine weeks. Instructional materials are not provided. Course objectives include: (1) exploration of foreign languages and cultures; (2) sensitization to value systems and customs of one's own and other…

Guidelines for Out-of-School Credit in Foreign Travel.

ERIC Educational Resources Information Center

Hartman, Don, Comp.; Hutto, Max, Comp.

Guidelines for out-of-school credit in foreign travel through the Foreign Study Program for high school students are presented. This program is offered to high school students in a format that encompasses areas contiguous to all major curriculum courses of the secondary school. The following topics are addressed: (1) program goals and objectives,…

The Foreign Language and Intercultural Competence Teacher: The Acquisition of a New Professional Identity

ERIC Educational Resources Information Center

Sercu, Lies

2006-01-01

It has now become commonplace to state that foreign language learning should be viewed in an intercultural perspective. The main objective of foreign language education is no longer defined strictly in terms of the acquisition of communicative competence. Teachers are now required to teach intercultural communicative competence. The aim of the…

A Tale of One China: How and Why Has the Efficacy of United States Arms Sales to Taiwan Changed Since 1990

DTIC Science & Technology

2016-05-01

militarily. Even Taiwan’s attempts to adopt asymmetric and innovative defense capabilities, paired with the advantages of island defense and foreign ...States foreign policy. According to the Defense Security Cooperation Agency, the United States transfers “defense articles and services in furtherance...of national security and foreign policy objectives.” By increasing the military capabilities of foreign allies and partners, the United States

Ultrasound detection of simulated intra-ocular foreign bodies by minimally trained personnel.

PubMed

Sargsyan, Ashot E; Dulchavsky, Alexandria G; Adams, James; Melton, Shannon; Hamilton, Douglas R; Dulchavsky, Scott A

2008-01-01

To test the ability of non-expert ultrasound operators of divergent backgrounds to detect the presence, size, location, and composition of foreign bodies in an ocular model. High school students (N = 10) and NASA astronauts (N = 4) completed a brief ultrasound training session which focused on basic ultrasound principles and the detection of foreign bodies. The operators used portable ultrasound devices to detect foreign objects of varying location, size (0.5-2 mm), and material (glass, plastic, metal) in a gelatinous ocular model. Operator findings were compared to known foreign object parameters and ultrasound experts (N = 2) to determine accuracy across and between groups. Ultrasound had high sensitivity (astronauts 85%, students 87%, and experts 100%) and specificity (astronauts 81%, students 83%, and experts 95%) for the detection of foreign bodies. All user groups were able to accurately detect the presence of foreign bodies in this model (astronauts 84%, students 81%, and experts 97%). Astronaut and student sensitivity results for material (64% vs. 48%), size (60% vs. 46%), and position (77% vs. 64%) were not statistically different. Experts' results for material (85%), size (90%), and position (98%) were higher; however, the small sample size precluded statistical conclusions. Ultrasound can be used by operators with varying training to detect the presence, location, and composition of intraocular foreign bodies with high sensitivity, specificity, and accuracy.

On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete

PubMed Central

Martynenko, V.; Martínez Krahmer, D.; Benítez, A.; Genovese, G.

2018-01-01

The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade. The results exhibit the cutting blade SB-A, which has twice the density of diamonds and large contact area, exhibits less wear even though the material removal rate is higher compared with the other two cutting blades. Additionally, the surface topography of the different blades is evaluated to examine the impact of wear depending on the surface profile and the distribution of the diamonds in the blade’s matrix. Large number of diamonds pull-out are found in blades type SB-C, which additionally shows the worst wear resistant capability. As a conclusion, the cutting efficiency of the blade is found to be related to the density of embedded diamonds and the type of the surface profile of the cutting blade after reaching the stop criteria. PMID:29425125

On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete.

PubMed

Sánchez Egea, A J; Martynenko, V; Martínez Krahmer, D; López de Lacalle, L N; Benítez, A; Genovese, G

2018-02-09

The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade. The results exhibit the cutting blade SB-A, which has twice the density of diamonds and large contact area, exhibits less wear even though the material removal rate is higher compared with the other two cutting blades. Additionally, the surface topography of the different blades is evaluated to examine the impact of wear depending on the surface profile and the distribution of the diamonds in the blade's matrix. Large number of diamonds pull-out are found in blades type SB-C, which additionally shows the worst wear resistant capability. As a conclusion, the cutting efficiency of the blade is found to be related to the density of embedded diamonds and the type of the surface profile of the cutting blade after reaching the stop criteria.

Bearing-Foreign Material Deposition on Retrieved Co-Cr Femoral Heads: Composition and Morphology

PubMed Central

Tikekar, Nishant M.; Heiner, Anneliese D.; Baer, Thomas E.; Kruger, Karen M.; Callaghan, John J.; Brown, Thomas D.; Lannutti, John J.

2015-01-01

Bearing-foreign material deposition onto a femoral head can occur from contact with an acetabular shell due to dislocation, reduction, or subluxation. The purpose of this study was to comprehensively characterize deposit regions on retrieved cobalt-chrome femoral heads from metal-on-polyethylene total hip arthroplasties that had experienced such adverse events. The morphology, topography, and composition of deposition regions were characterized using macrophotography, optical profilometry, scanning electron microscopy, energy dispersive spectroscopy, and X-ray photoelectron spectroscopy. The deposit areas were relatively large, they were much rougher than the surrounding undamaged clean areas, and they displayed several distinct morphologies. Titanium alloy elements were the predominant constituents. Calcium and phosphorous were also detected within the deposit areas, in a composition that could nucleate abrasive hydroxyapatite. In addition, tungsten-rich particles, likely present as tungsten carbide, were observed on top of the titanium deposits. The increased roughness associated with these deposition features would be expected to accelerate damage and wear of the opposing liner and hence accelerate the development of osteolysis. PMID:26236744

A rare cause of gastric obstruction: Lighters swallowing.

PubMed

Aday, Ulas; Tardu, Ali; Yagci, Mehmet Ali; Yonder, Huseyin

2015-01-01

The majority of swallowed foreign bodies are thrown spontaneously without causing complications in the digestive system. Multiple number of foreign bodies may be swallowed by psychiatric patients which delay diagnosis and increase the complication rate. Long and hard objects cannot pass through the pylorus, and may cause obstruction, ulceration, bleeding and perforation. Endoscopy is used as an effective method in such cases. An exploratory laparatomy was performed after unsuccessful endoscopic foreign object removal in a 28-year-old schizophrenic patient with gastric outlet obstruction due to multiple cigarette lighter swallowing. Ten lighters were removed from the stomach through gastrotomy and one more lighter was removed from the descending colon by milking through the anus. The aim of this paper is to discuss encountered difficulties in psychiatric patients who underwent surgery due to intake of foreign bodies.

Water used to visualize and remove hidden foreign bodies from the external ear canal.

PubMed

Peltola, T J; Saarento, R

1992-02-01

Small foreign bodies lodged anteriorly in the tympanic sulcus are usually not visible, due to the curve of the external ear canal. Such objects can be seen with the aid of an otomicroscope and micromirror or with an endoscope, and removed by irrigation. If irrigation fails, epithelial migration on the tympanic membrane may remove lodged foreign bodies, although this may take months. Our new method, which uses water to locate small objects lodged in the tympanic sulcus, includes irrigation of the ear, adjustment of the water level to the middle curve of the external ear canal, and use of the water surface as a concave lens, making the tympanic sulcus visible. With otomicroscopy a curved ear probe can then be used to remove lodged foreign bodies from behind the curve.

Superior accuracy of model-based radiostereometric analysis for measurement of polyethylene wear

PubMed Central

Stilling, M.; Kold, S.; de Raedt, S.; Andersen, N. T.; Rahbek, O.; Søballe, K.

2012-01-01

Objectives The accuracy and precision of two new methods of model-based radiostereometric analysis (RSA) were hypothesised to be superior to a plain radiograph method in the assessment of polyethylene (PE) wear. Methods A phantom device was constructed to simulate three-dimensional (3D) PE wear. Images were obtained consecutively for each simulated wear position for each modality. Three commercially available packages were evaluated: model-based RSA using laser-scanned cup models (MB-RSA), model-based RSA using computer-generated elementary geometrical shape models (EGS-RSA), and PolyWare. Precision (95% repeatability limits) and accuracy (Root Mean Square Errors) for two-dimensional (2D) and 3D wear measurements were assessed. Results The precision for 2D wear measures was 0.078 mm, 0.102 mm, and 0.076 mm for EGS-RSA, MB-RSA, and PolyWare, respectively. For the 3D wear measures the precision was 0.185 mm, 0.189 mm, and 0.244 mm for EGS-RSA, MB-RSA, and PolyWare respectively. Repeatability was similar for all methods within the same dimension, when compared between 2D and 3D (all p > 0.28). For the 2D RSA methods, accuracy was below 0.055 mm and at least 0.335 mm for PolyWare. For 3D measurements, accuracy was 0.1 mm, 0.2 mm, and 0.3 mm for EGS-RSA, MB-RSA and PolyWare respectively. PolyWare was less accurate compared with RSA methods (p = 0.036). No difference was observed between the RSA methods (p = 0.10). Conclusions For all methods, precision and accuracy were better in 2D, with RSA methods being superior in accuracy. Although less accurate and precise, 3D RSA defines the clinically relevant wear pattern (multidirectional). PolyWare is a good and low-cost alternative to RSA, despite being less accurate and requiring a larger sample size. PMID:23610688

Estimation of the influence of tool wear on force signals: A finite element approach in AISI 1045 orthogonal cutting

NASA Astrophysics Data System (ADS)

Equeter, Lucas; Ducobu, François; Rivière-Lorphèvre, Edouard; Abouridouane, Mustapha; Klocke, Fritz; Dehombreux, Pierre

2018-05-01

Industrial concerns arise regarding the significant cost of cutting tools in machining process. In particular, their improper replacement policy can lead either to scraps, or to early tool replacements, which would waste fine tools. ISO 3685 provides the flank wear end-of-life criterion. Flank wear is also the nominal type of wear for longest tool lifetimes in optimal cutting conditions. Its consequences include bad surface roughness and dimensional discrepancies. In order to aid the replacement decision process, several tool condition monitoring techniques are suggested. Force signals were shown in the literature to be strongly linked with tools flank wear. It can therefore be assumed that force signals are highly relevant for monitoring the condition of cutting tools and providing decision-aid information in the framework of their maintenance and replacement. The objective of this work is to correlate tools flank wear with numerically computed force signals. The present work uses a Finite Element Model with a Coupled Eulerian-Lagrangian approach. The geometry of the tool is changed for different runs of the model, in order to obtain results that are specific to a certain level of wear. The model is assessed by comparison with experimental data gathered earlier on fresh tools. Using the model at constant cutting parameters, force signals under different tool wear states are computed and provide force signals for each studied tool geometry. These signals are qualitatively compared with relevant data from the literature. At this point, no quantitative comparison could be performed on worn tools because the reviewed literature failed to provide similar studies in this material, either numerical or experimental. Therefore, further development of this work should include experimental campaigns aiming at collecting cutting forces signals and assessing the numerical results that were achieved through this work.

33 CFR 150.611 - What head protection is required?

Code of Federal Regulations, 2010 CFR

2010-07-01

... of injury from falling objects or contact with electrical conductors, personnel working or visiting such an area wear head protectors designed to protect them against such injury and complying with 29...

Fitting Tips and Visual Rehabilitation of Irregular Cornea with a New Design of Corneoscleral Contact Lens: Objective and Subjective Evaluation

PubMed Central

Kishk, Hanem; Elwan, Mohamed M.; Abouelkheir, Hossam Youssef

2018-01-01

Objectives To study the fitting and the visual rehabilitation obtained with a corneoscleral contact lens, namely, Rose K2 XL in patients with irregular cornea. Methods This prospective study included 36 eyes of 36 patients with irregular cornea fitted with Rose K2 XL. Refractive and visual outcomes and mesopic and aberrometric parameters of fitted eyes were assessed at 2 weeks, 3 months, and 6 months after the initial lens use. Objective and subjective parameters of patient satisfaction and lens comfort were noted. Causes of lens discontinuation and complications were also recorded. Results Average logMAR VA improved significantly from 0.95 ± 0.09 without correction to 0.04 ± 0.05 six months after lens wear. Similarly, mesopic and aberrometric measures were significantly improved. Statistical analysis of the subjective patients' responses showed a significant acceptance of the lens by most of them. At the end of follow-up, the mean wearing time was 9.9 ± 2.9 hours per day. The most common cause of wearing discontinuation was persistent discomfort (16.7%) and high lens expenses(16.7%). Self-assessed questionnaire showed statistically significant improvement in nearly all measured subjective parameters. Conclusion Rose K2 XL lenses provide patients with irregular cornea with both quantitative and qualitative optimal visual function with high degree of patient comfort and satisfaction. PMID:29484205

Histologic study of periprosthetic osteolytic lesions after AES total ankle replacement. A 22 case series.

PubMed

Dalat, F; Barnoud, R; Fessy, M-H; Besse, J-L

2013-10-01

Medium-term results for total ankle replacement (TAR) are in general satisfactory, but there is a high redo rate for periprosthetic osteolysis associated with the AES implant. Comparing radioclinical findings and histologic analysis of implant revision procedure specimens can account for the elevated rate of osteolysis associated with the AES TAR implant. In a prospective series of 84 AES TAR implants (2003-2008), 25 underwent revision for osteolysis (including three undergoing revision twice) at a mean 59.8 months. Eight patients had hydroxyapatite (HA) coated models and the others had titanium-hydroxyapatite (Ti-HA) coatings. Radiographs were systematically analyzed on Besse's protocol and evolution was monitored on AOFAS scores. The 94 specimens taken for histologic analysis during revision were re-examined, focusing specifically on foreign bodies. Macroscopically, no metallosis or polyethylene wear was found at revision. AOFAS global and pain scores fell respectively from 89.7/100 at 1 year postoperatively to 72.9 before revision and from 32.5/40 to 20.6/40, although global scores were unchanged in 25% of patients. Radiologically, all patients showed tibial and talar osteolytic lesions, 45% showed cortical lysis and in 25% the implant had collapsed into the cysts. All specimens showed macrophagic granulomatous inflammatory reactions in contact with a foreign body; the cysts showed necrotic remodeling. Some of the foreign bodies could be identified on optical histologic examination with polyethylene in 95% of the specimens and metal in 60% (100% of HA-coated models and 33.3% of Ti-HA-coated models). Unidentifiable material was associated: a brownish pigment in Ti-HA-coated models (33.3%) and flakey bodies in 44.4% of the HA-coated models and 18.2% of the Ti-HA-coated models. The phenomenon of periprosthetic osteolysis is still poorly understood, although implant wear debris seems to be implicated. All the patients with HA-coated implants with modular tibial stem had metal particles in the tissue around the implant, although their exact nature could not be determined. The double-layer Ti-HA coating may induce delamination by fretting while the biological bone anchorage is forming. Prospective cohort study - Level IV. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

Foreign Language Exploratory (French, German, Spanish), (6-8), Resource Guide and Handbook.

ERIC Educational Resources Information Center

Kennedy, Dora F.; And Others

The guide focuses on a rationale for exploratory foreign language courses in middle or junior high school, and on the goals and objectives for such courses. An exploratory course may serve a number of purposes regardless of whether or not a pupil elects a foreign language at a later time. These purposes include: (1) acquainting pupils with a…

Development of a smartphone application to measure physical activity using sensor-assisted self-report.

PubMed

Dunton, Genevieve Fridlund; Dzubur, Eldin; Kawabata, Keito; Yanez, Brenda; Bo, Bin; Intille, Stephen

2014-01-01

Despite the known advantages of objective physical activity monitors (e.g., accelerometers), these devices have high rates of non-wear, which leads to missing data. Objective activity monitors are also unable to capture valuable contextual information about behavior. Adolescents recruited into physical activity surveillance and intervention studies will increasingly have smartphones, which are miniature computers with built-in motion sensors. This paper describes the design and development of a smartphone application ("app") called Mobile Teen that combines objective and self-report assessment strategies through (1) sensor-informed context-sensitive ecological momentary assessment (CS-EMA) and (2) sensor-assisted end-of-day recall. The Mobile Teen app uses the mobile phone's built-in motion sensor to automatically detect likely bouts of phone non-wear, sedentary behavior, and physical activity. The app then uses transitions between these inferred states to trigger CS-EMA self-report surveys measuring the type, purpose, and context of activity in real-time. The end of the day recall component of the Mobile Teen app allows users to interactively review and label their own physical activity data each evening using visual cues from automatically detected major activity transitions from the phone's built-in motion sensors. Major activity transitions are identified by the app, which cues the user to label that "chunk," or period, of time using activity categories. Sensor-driven CS-EMA and end-of-day recall smartphone apps can be used to augment physical activity data collected by objective activity monitors, filling in gaps during non-wear bouts and providing additional real-time data on environmental, social, and emotional correlates of behavior. Smartphone apps such as these have potential for affordable deployment in large-scale epidemiological and intervention studies.

Development of a Smartphone Application to Measure Physical Activity Using Sensor-Assisted Self-Report

PubMed Central

Dunton, Genevieve Fridlund; Dzubur, Eldin; Kawabata, Keito; Yanez, Brenda; Bo, Bin; Intille, Stephen

2013-01-01

Introduction: Despite the known advantages of objective physical activity monitors (e.g., accelerometers), these devices have high rates of non-wear, which leads to missing data. Objective activity monitors are also unable to capture valuable contextual information about behavior. Adolescents recruited into physical activity surveillance and intervention studies will increasingly have smartphones, which are miniature computers with built-in motion sensors. Methods: This paper describes the design and development of a smartphone application (“app”) called Mobile Teen that combines objective and self-report assessment strategies through (1) sensor-informed context-sensitive ecological momentary assessment (CS-EMA) and (2) sensor-assisted end-of-day recall. Results: The Mobile Teen app uses the mobile phone’s built-in motion sensor to automatically detect likely bouts of phone non-wear, sedentary behavior, and physical activity. The app then uses transitions between these inferred states to trigger CS-EMA self-report surveys measuring the type, purpose, and context of activity in real-time. The end of the day recall component of the Mobile Teen app allows users to interactively review and label their own physical activity data each evening using visual cues from automatically detected major activity transitions from the phone’s built-in motion sensors. Major activity transitions are identified by the app, which cues the user to label that “chunk,” or period, of time using activity categories. Conclusion: Sensor-driven CS-EMA and end-of-day recall smartphone apps can be used to augment physical activity data collected by objective activity monitors, filling in gaps during non-wear bouts and providing additional real-time data on environmental, social, and emotional correlates of behavior. Smartphone apps such as these have potential for affordable deployment in large-scale epidemiological and intervention studies. PMID:24616888

Development of pulmonary alveolar proteinosis following exposure to dust after the Great East Japan Earthquake.

PubMed

Hisata, Shu; Moriyama, Hiroshi; Tazawa, Ryushi; Ohkouchi, Shinya; Ichinose, Masakazu; Ebina, Masahito

2013-12-01

We report a unique case of pulmonary alveolar proteinosis that developed 3 weeks after the Great East Japan Earthquake and the subsequent tsunami. The patient had inhaled dust repeatedly while visiting her devastated neighborhood without wearing a protective mask. Five weeks after the earthquake, lung samples taken from the patient showed foreign particle deposition; however, her serum was negative for GM-CSF autoantibody. The patient's clinical symptoms resolved following whole lung lavage. We conclude that inhalation of fine dust particles after natural disasters may cause the onset of pulmonary alveolar proteinosis. Copyright © 2013 The Japanese Respiratory Society. Published by Elsevier B.V. All rights reserved.

Individual 3D measurements of end users to personalize work wear clothing

NASA Astrophysics Data System (ADS)

Mielicka, E.; Napieralska, L.; Jasińska, I.; Jarzyna, V.

2017-10-01

Body silhouette 3D measurements need to be performed separately in each country due to significant ethnic differences in body silhouette which preclude the transfer of European data to particular countries. Systematic research allows to update information on the population body silhouette and body proportions as well as select the size changes possible to implement in clothing construction modifications. The diversity in body silhouettes and sizes as well as the issue of clothing fitting encourage clothing producers to provide work wear clothing based on individual measurements of the end users’ bodies. In the framework of the carried research, the group of construction workers was selected as the target group of the analysed work wear clothing users. 42 construction workers, men only, were measured. The body silhouette measurement process was non-contact and was carried out with the use of 3D body scanner. The collected data on the body silhouette allowed to select sizes used to construct the work wear clothing and identify the clothing size. The selected measurement points of the body silhouette underwent statistical analysis to determine the distribution of random variables, here body sizes. The variables distribution characteristics were calculated. On that basis, the fitting appraisal of work wear clothing with respect to the size of the finished product corresponding to the adequate size of individually measured worker/end user was performed. The size overview of the work wear clothing used by the specific professional group and the appraisal of the size fitting to the body silhouette took into consideration the work wear clothing ergonomic functionality with respect to the body posture when performing the tasks, design and clothing construction. The analysis based on the currently gathered end users’ remarks and objections concerning the clothing fitting and performed body silhouette measurements allows to modify the existing work wear clothing for the selected group of end users. The research was aimed at the improvement of the work wear clothing fitting thanks to personalization based on individual body measurements at the stage of construction design.

Management of ingested foreign bodies in childhood: our experience and review of the literature.

PubMed

Hachimi-Idrissi, S; Corne, L; Vandenplas, Y

1998-09-01

The management of foreign bodies in the gastrointestinal tract is not standardized. Retrospectively, we analysed the management of 174 cases of accidental ingestion of foreign bodies in children. No child had ingested more than one foreign object. The ingested foreign bodies were: coins, toy parts, jewels, batteries, 'sharp' materials such as needles and pins, fish and chicken bone, and 'large' amounts of food. Of the patients 51% had transient symptoms at the moment of ingestion, such as retrosternal pain, cyanosis and dysphasia. Attempts to extract the foreign body either by a magnet tube, endoscopy or McGill forceps was performed in 83 patients. The majority of the extracted foreign bodies were batteries and sharp materials. The outcome of all the patients was excellent. No complications were observed.

Negligible heat strain in armored vehicle officers wearing personal body armor

PubMed Central

2011-01-01

Objectives This study evaluated the heat strain experienced by armored vehicle officers (AVOs) wearing personal body armor (PBA) in a sub-tropical climate. Methods Twelve male AVOs, aged 35-58 years, undertook an eight hour shift while wearing PBA. Heart rate and core temperature were monitored continuously. Urine specific gravity (USG) was measured before and after, and with any urination during the shift. Results Heart rate indicated an intermittent and low-intensity nature of the work. USG revealed six AVOs were dehydrated from pre through post shift, and two others became dehydrated. Core temperature averaged 37.4 ± 0.3°C, with maximum's of 37.7 ± 0.2°C. Conclusions Despite increased age, body mass, and poor hydration practices, and Wet-Bulb Globe Temperatures in excess of 30°C; the intermittent nature and low intensity of the work prevented excessive heat strain from developing. PMID:21801453

Laser dispersing of ceramic powders into Al-alloys

NASA Astrophysics Data System (ADS)

Jendrzejewski, Rafał; Van Acker, Karel; Vanhoyweghen, Dirk

2007-02-01

The general objective of the work was formation of highly wear resistant metal matrix composite (MMC) surface layers on aluminium based Al 6061 alloy by means of laser dispersing. The surface of the substrate is locally melted by the high power diode laser beam and simultaneously powder particles are injected into molten material. The optimal process parameter window for the laser dispersing of SiC in Al 6061 has been found. The measured values of the wear rates of the sample with dispersed SiC particles are about seven times lower than that of the reference Al-substrates. Results show that laser dispersing is highly promising technology to improve the surface, mainly wear properties of light metals. However the possibilities of industrial application are still limited due to considerable laser beam power and preheating temperature applied as well low productivity because of low scanning speed, and therefore further investigations are required.

Surface roughness model based on force sensors for the prediction of the tool wear.

PubMed

de Agustina, Beatriz; Rubio, Eva María; Sebastián, Miguel Ángel

2014-04-04

In this study, a methodology has been developed with the objective of evaluating the surface roughness obtained during turning processes by measuring the signals detected by a force sensor under the same cutting conditions. In this way, the surface quality achieved along the process is correlated to several parameters of the cutting forces (thrust forces, feed forces and cutting forces), so the effect that the tool wear causes on the surface roughness is evaluated. In a first step, the best cutting conditions (cutting parameters and radius of tool) for a certain quality surface requirement were found for pieces of UNS A97075. Next, with this selection a model of surface roughness based on the cutting forces was developed for different states of wear that simulate the behaviour of the tool throughout its life. The validation of this model reveals that it was effective for approximately 70% of the surface roughness values obtained.

Development of fuel wear tests using the Cameron-Plint High-Frequency reciprocating machine. Interim report, March 1988-May 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kanakia, M.D.; Cuellar, J.P.; Lestz, S.J.

The objectives of this program were to develop laboratory bench fuel-wear test methodology using JP-8 and to evaluate the effects of additives to improve load-carrying capacity of JP-8 for use in diesel-powered ground equipment. A laboratory test using the Cameron-Plint High-Frequency Reciprocating machine evaluated the effects of various chemical and physical parameters influencing the lubricity of the distillate fuels. The test conditions were determined sufficient to eliminate the effect of fluid physical properties such as viscosity. It was shown that the differences in the intrinsic lubricity of the fuels were due to small amounts of chemical additives. Under such conditions,more » the test can be used as a screening tool to find additives for enhancement of JP-8 lubricity. The test has potential to ascertain minimum lubricity level for diesel-powered ground equipment if these requirements are verified with field performance data and determined to be different from the Air Force JP-8 specifications. The dimensionless wear coefficients of Reference No. 2 diesel fuel were shown to be an order of magnitude lower than the jet fuels. In all cases, the wear rates of jet fuels and isoparaffinic solvents were improved by addition of a corrosion inhibitor or antiwear additive to match the lower wear rates of the diesel fuels. Although there was no measurable change in the viscosities of the jet fuel due to the additives, the wear rates changed by an order of magnitude.« less

Impact of fixed orthodontic appliance or clear-aligner on daily performance, in adult patients with moderate need for treatment

PubMed Central

Lin, Feiou; Yao, Linjie; Bhikoo, Chandradev; Guo, Jing

2016-01-01

Objective To assess the impact of wearing fixed orthodontic appliance (FOA) or clear-aligner, on daily performance in adult patients. Methods The Oral Impacts on Daily Performance (OIDP) index was assessed in 152 adults aged 25–35 years at baseline (T0), 6 months after bonding (T1), and 12 months after bonding (T2). Participants were randomly divided into two groups: CA group (participants treated with clear-aligner) and a control group (FOA group; participants treated with FOA). Baseline malocclusion severity was assessed using the Index of Orthodontic Treatment Need. Results There were no significant differences in sociodemographic variables and OIDP scores at baseline between the two groups. Significant changes in OIDP total and subscale scores were observed while wearing FOA: OIDP total score and subscale scores of eating, cleaning teeth, smiling, and social relation at T1 and T2 were significantly higher than at baseline (P<0.05 or P<0.01). However, only OIDP total score was significantly increased at T1 compared to the baseline in the CA group. OIDP total score and subscale scores of eating, cleaning teeth, smiling, and social relation were significantly higher in patients wearing FOA than in patients wearing clear-aligner at T1 and T2 (P<0.05 or P<0.01). Conclusion Patients wearing clear-aligner have fewer impacts on daily life than those wearing FOA during treatment, and have no significant changes in OIPD subscale scores at 12 months. FOA therapy significantly impacts daily performance in adult patients during treatment. PMID:27616881

Experimental study on deep hole drilling of 17-4PH material

NASA Astrophysics Data System (ADS)

Uzhanfeng, LI; Uquantai, LI

2018-02-01

This paper uses 17-4PH material as the research object, according to the material characteristics of 17-4PH, designed and carried out deep hole drilling test. The purpose of the experiment is to study and discuss the three major problems of tool wear, chip shape and axial deviation of the hole in the process of deep hole drilling of 17-4PH materials. Through the deep hole drilling test of 17-4PH material, the variation of the chip shape and the deflection of the hole axis was obtained under different wear conditions.

Optimizing the milling characteristics of Al-SiC particulate composites

NASA Astrophysics Data System (ADS)

Karthikeyan, R.; Raghukandan, K.; Naagarazan, R. S.; Pai, B. C.

2000-12-01

The present investigation focuses on the face milling characteristics of LM25Al-SiC particulate composites produced through stir casting. Experiments were conducted according to an L27 orthogonal array and mathematical models were developed for such machining characteristics as flank wear, specific energy and surface roughness whose adequacy was checked. The insignificant effects present in the models were eliminated using a t-test. Goal programming was employed to optimize the cutting conditions by considering such primary objectives as maximizing the metal removal rate and minimizing tool wear, specific energy and surface roughness.

Comprehensive study of the abrasive wear and slurry erosion behavior of an expanded system of high chromium cast iron and microstructural modification for enhanced wear resistance

NASA Astrophysics Data System (ADS)

Chung, Reinaldo Javier

High chromium cast irons (HCCIs) have been demonstrated to be an effective material for a wide range of applications in aggressive environments, where resistances to abrasion, erosion and erosion-corrosion are required. For instance, machinery and facilities used in mining and extraction in Alberta's oil sands suffer from erosion and erosion-corrosion caused by silica-containing slurries, which create challenges for the reliability and maintenance of slurry pumping systems as well as other processing and handling equipment. Considerable efforts have been made to determine and understand the relationship between microstructural features of the HCCIs and their wear performance, in order to guide the material selection and development for specific service conditions with optimal performance. The focus was previously put on a narrow group of compositions dictated by ASTM A532. However, with recent advances in casting technology, the HCCI compositional range can be significantly expanded, which potentially brings new alloys that can be superior to those which are currently employed. This work consists of three main aspects of study. The first one is the investigation of an expanded system of white irons with their composition ranging from 1 to 6 wt.% C and 5 to 45 wt.% Cr, covering 53 alloys. This work has generated wear and corrosion maps and established correlation between the performance and microstructural features for the alloys. The work was conducted in collaboration with the Materials Development Center of Weir Minerals in Australia, and the results have been collected in a database that is used by the company to guide materials selection for slurry pump components in Alberta oil sands and in other mining operations throughout the world. The second part consists of three case studies on effects of high chromium and high carbon, respectively, on the performance of the HCCIs. The third aspect is the development of an approach to enhance the wear resistance of HCCIs by microstructural modification through addition of strong carbide-forming elements to produce eutectic microstructures reinforced with in-situ formed foreign carbides. Very promising results have been obtained in lab, which demonstrates that the approach is feasible and effective in tailoring HCCIs for improved performance.

Dental microwear textures: reconstructing diets of fossil mammals

NASA Astrophysics Data System (ADS)

DeSantis, Larisa R. G.

2016-06-01

Dietary information of fossil mammals can be revealed via the analysis of tooth morphology, tooth wear, tooth geochemistry, and the microscopic wear patterns on tooth surfaces resulting from food processing. Although dental microwear has long been used by anthropologists and paleontologists to clarify diets in a diversity of mammals, until recently these methods focused on the counting of wear features (e.g., pits and scratches) from two-dimensional surfaces (typically via scanning electron microscopes or low-magnification light microscopes). The analysis of dental microwear textures can instead reveal dietary information in a broad range of herbivorous, omnivorous, and carnivorous mammals by characterizing microscopic tooth surfaces in three-dimensions, without the counting of individual surface features. To date, dental microwear textures in ungulates, xenarthrans, marsupials, carnivorans, and primates (including humans and their ancestors) are correlated with known dietary behavior in extant taxa and reconstruct ancient diets in a diversity of prehistoric mammals. For example, tough versus hard object feeding can be characterized across disparate phylogenetic groups and can distinguish grazers, folivorous, and flesh consumers (tougher food consumers) from woody browsers, frugivores, and bone consumers (harder object feeders). This paper reviews how dental microwear textures can be useful to reconstructing diets in a broad array of living and extinct mammals, with commentary on areas of future research.

The use of pedometers for monitoring physical activity in children and adolescents: measurement considerations.

PubMed

Clemes, Stacy A; Biddle, Stuart J H

2013-02-01

Pedometers are increasingly being used to measure physical activity in children and adolescents. This review provides an overview of common measurement issues relating to their use. Studies addressing the following measurement issues in children/adolescents (aged 3-18 years) were included: pedometer validity and reliability, monitoring period, wear time, reactivity, and data treatment and reporting. Pedometer surveillance studies in children/adolescents (aged: 4-18 years) were also included to enable common measurement protocols to be highlighted. In children > 5 years, pedometers provide a valid and reliable, objective measure of ambulatory activity. Further evidence is required on pedometer validity in preschool children. Across all ages, optimal monitoring frames to detect habitual activity have yet to be determined; most surveillance studies use 7 days. It is recommended that standardized wear time criteria are established for different age groups, and that wear times are reported. As activity varies between weekdays and weekend days, researchers interested in habitual activity should include both types of day in surveillance studies. There is conflicting evidence on the presence of reactivity to pedometers. Pedometers are a suitable tool to objectively assess ambulatory activity in children (> 5 years) and adolescents. This review provides recommendations to enhance the standardization of measurement protocols.

Increased BMI in children-an indicator for less compliance during orthodontic treatment with removable appliances.

PubMed

von Bremen, Julia; Lorenz, Nathalie; Ludwig, Björn; Ruf, Sabine

2018-02-19

To assess whether or not childhood overweight is associated with lower levels of compliance during orthodontic therapy with removable appliances. Starting in 2011, all upper expansion plates and Sander II appliances were equipped with a Theramon® microsensor chip to assess appliance wear time objectively. According to their pre-treatment, BMI normal weight patients were matched to consecutively treated overweight or obese patients by gender, age, and appliance type. Cooperation was assessed with microelectronic wear time documentation over a period of at least 6 months. A total of 50 patients (25 overweight, 25 normal weight) with upper expansion plates and 64 patients (32 overweight, 32 normal weight) with Sander II appliances were analysed. Spearman Rho coefficients showed an indirect association between BMI and appliance wear time, indicating that the higher the BMI, the less the patients wore their appliances (P < 0.05). Furthermore, both normal- and overweight children wore upper expansion plates significantly more than Sander II appliances (P < 0.05). Although no gender-specific difference was found (P = 0.723), an age-related correlation could be verified, indicating a decrease in wear time with increasing age (P < 0.05). An increased BMI appears to be a risk factor for less appliance wear during orthodontic treatment with removable appliances. Additional factors which influenced cooperation during treatment with removable appliances were patient age and appliance type.

Practical considerations for volumetric wear analysis of explanted hip arthroplasties

PubMed Central

Langton, D. J.; Sidaginamale, R. P.; Holland, J. P.; Deehan, D.; Joyce, T. J.; Nargol, A. V. F.; Meek, R. D.; Lord, J. K.

2014-01-01

Objectives Wear debris released from bearing surfaces has been shown to provoke negative immune responses in the recipient. Excessive wear has been linked to early failure of prostheses. Analysis using coordinate measuring machines (CMMs) can provide estimates of total volumetric material loss of explanted prostheses and can help to understand device failure. The accuracy of volumetric testing has been debated, with some investigators stating that only protocols involving hundreds of thousands of measurement points are sufficient. We looked to examine this assumption and to apply the findings to the clinical arena. Methods We examined the effects on the calculated material loss from a ceramic femoral head when different CMM scanning parameters were used. Calculated wear volumes were compared with gold standard gravimetric tests in a blinded study. Results Various scanning parameters including point pitch, maximum point to point distance, the number of scanning contours or the total number of points had no clinically relevant effect on volumetric wear calculations. Gravimetric testing showed that material loss can be calculated to provide clinically relevant degrees of accuracy. Conclusions Prosthetic surfaces can be analysed accurately and rapidly with currently available technologies. Given these results, we believe that routine analysis of explanted hip components would be a feasible and logical extension to National Joint Registries. Cite this article: Bone Joint Res 2014;3:60–8. PMID:24627327

The influence of wearing compression stockings on performance indicators and physiological responses following a prolonged trail running exercise.

PubMed

Vercruyssen, Fabrice; Easthope, Christopher; Bernard, Thierry; Hausswirth, Christophe; Bieuzen, Francois; Gruet, Mathieu; Brisswalter, Jeanick

2014-01-01

The objective of this study was to investigate the effects of wearing compression socks (CS) on performance indicators and physiological responses during prolonged trail running. Eleven trained runners completed a 15.6 km trail run at a competition intensity whilst wearing or not wearing CS. Counter movement jump, maximal voluntary contraction and the oxygenation profile of vastus lateralis muscle using near-infrared spectroscopy (NIRS) method were measured before and following exercise. Run time, heart rate (HR), blood lactate concentration and ratings of perceived exertion were evaluated during the CS and non-CS sessions. No significant difference in any dependent variables was observed during the run sessions. Run times were 5681.1 ± 503.5 and 5696.7 ± 530.7 s for the non-CS and CS conditions, respectively. The relative intensity during CS and non-CS runs corresponded to a range of 90.5-91.5% HRmax. Although NIRS measurements such as muscle oxygen uptake and muscle blood flow significantly increased following exercise (+57.7% and + 42.6%,+59.2% and + 32.4%, respectively for the CS and non-CS sessions, P<0.05), there was no difference between the run conditions. The findings suggest that competitive runners do not gain any practical or physiological benefits from wearing CS during prolonged off-road running.

Hardness and modulus of elasticity of primary and permanent teeth after wear against different dental materials

PubMed Central

Galo, Rodrigo; Contente, Marta Maria Martins Giamatei; Galafassi, Daniel; Borsatto, Maria Cristina

2015-01-01

Objectives: The purpose of this study was to determine the Young's modulus and the hardness of deciduous and permanent teeth following wear challenges using different dental materials. Materials and Methods: Wear challenges were performed against four dental materials: A resin-based fissure sealant (Fluoroshield®), a glass ionomer based fissure sealant (Vitremer®), and two microhybrid composite resins (Filtek Z250 and P90®). Using the pin-on-plate design, a deciduous or a permanent tooth was made into a pin (4 mm × 4 mm × 2 mm) working at a 3 N vertical load, 1 Hz frequency, and 900 cycles (15 min) with Fusayama artificial saliva as a lubricant. Before and after the tribological tests, the hardness and elasticity modulus of the tooth samples were measured by creating a nanoindentation at load forces up to 50 mN and 150 mN. All of the results were statistically analyzed using ANOVA and post-hoc Duncan's tests (P < 0.05). Results: No difference in hardness was encountered between deciduous and permanent teeth (P < 0.05) or modulus of elasticity (P < 0.05) before or after the wear challenges for all of the dental materials tested. Conclusions: Wear challenges against the studied dental materials did not alter the properties of permanent or deciduous teeth after the application of a 3 N load. PMID:26929700

Vision screening in children: Is 7-9 years of age a threshold for visual impairment?

PubMed Central

Ertekin, Yusuf Haydar; Tekin, Murat; Uludag, Aysegul; Arikan, Sedat; Sahin, Erkan Melih

2016-01-01

Objective: The present study aimed to assess the prevalence of decreased visual acuity, strabismus, and spectacle wear in children aged 5 to 13 years. Methods: A cross-sectional study was performed in primary education schools. A total of 1938 participants, including 940 females (48.5%) and 998 males (51.5%) with a mean age 8.96 ± 2.31 (5-13 years old), were screened. The comparisons were performed with gender, age, and age groups. The children attended to vision screening were assigned to three age groups as 5-6 years, 7-9 years, and 10-13 years. Results: The prevalence of the parameters was detected as decreased visual acuity 12.4%, strabismus 2.2%, and spectacle wear 6.9%. The prevalence of decreased visual acuity was significantly higher in girls and in children aged 7-9 years old (p = 0.013, p < 0.001). The prevalence of spectacle wear was significantly higher in girls and in children aged 7-9 years old (p = 0.019, p < 0.001). There was a visual acuity decrease in 33 of 106 (31.1%) children despite wearing own spectacle. There was no significant difference among three age groups for strabismus. Conclusion: Increased prevalence of decreased visual acuity, as well as the higher frequency of spectacle wear in children at ages of 7-9 years old may point out a threshold for visual impairment. PMID:27882020

U.S. Foreign Aid to the Palestinians

DTIC Science & Technology

2009-05-15

government and does not change its stance toward Israel. Even if the immediate objectives of U.S. assistance programs for the Palestinians are met, lack of...In February 2008, then USAID Administrator and Director of U.S. Foreign Assistance Henrietta Fore said, in testimony before the House...more rigorous vetting measures. Testimony of Henrietta Fore, USAID Administrator and Director of U.S. Foreign Assistance, House Appropriations

U.S. Foreign Aid to the Palestinians

DTIC Science & Technology

2010-01-08

change its stance toward Israel. Even if the immediate objectives of U.S. assistance programs for the Palestinians are met, lack of progress toward a...Chicago Tribune, November 16, 2007. In February 2008, then-USAID Administrator and Director of U.S. Foreign Assistance Henrietta Fore said, in...was encouraging the adoption of more rigorous vetting measures. Testimony of Henrietta Fore, USAID Administrator and Director of U.S. Foreign

Development of a Newcastle disease virus vector expressing a foreign gene through an internal ribosomal entry site provides direct proof for a sequential transcription mechanism

USDA-ARS?s Scientific Manuscript database

Objectives: Newcastle disease virus (NDV), a member of the Paramxoviridae family, has been developed as a vector to express foreign genes for vaccine and gene therapy purposes. The foreign genes are usually inserted into a non-coding region of the NDV genome as an independent transcription unit (ITU...

English as a Foreign Language Students' Opinions about the Use of English on the Internet

ERIC Educational Resources Information Center

Coskun, Abdullah

2017-01-01

As in many other fields, the Internet has been used for educational purposes, especially for foreign language learning. This study has the main objective to investigate English as a Foreign Language (EFL) students' opinions about the use of English on the Internet. By means of a Likert-type questionnaire dealing with the use of English on the…

Nativity differences in allostatic load by age, sex, and Hispanic background from the Hispanic Community Health Study/Study of Latinos.

PubMed

Salazar, Christian R; Strizich, Garrett; Seeman, Teresa E; Isasi, Carmen R; Gallo, Linda C; Avilés-Santa, M Larissa; Cai, Jianwen; Penedo, Frank J; Arguelles, Willian; Sanders, Anne E; Lipton, Richard B; Kaplan, Robert C

2016-12-01

Allostatic load (AL), an index of biological "wear and tear" on the body from cumulative exposure to stress, has been little studied in US Hispanics/Latinos. We investigated AL accumulation patterns by age, sex, and nativity in the Hispanic Community Health Study/Study of Latinos. We studied 15,830 Hispanic/Latinos of Mexican, Cuban, Dominican, Puerto Rican, Central and South American descent aged 18-74 years, 77% of whom were foreign-born. Consistent with the conceptualization of AL, we developed an index based upon 16 physiological markers that spanned the cardiometabolic, parasympathetic, and inflammatory systems. We computed mean adjusted AL scores using log-linear models across age-groups (18-44, 45-54, 55-74 years), by sex and nativity status. Among foreign-born individuals, differences in AL by duration of residence in the US (<10, ≥10 years) and age at migration (<24, ≥24 years) were also examined. In persons younger than 55 years old, after controlling for socioeconomic and behavioral factors, AL was highest among US-born individuals, intermediate in foreign-born Hispanics/Latinos with longer duration in the US (≥10 years), and lowest among those with shorter duration in the US (<10 years) ( P <0.0001 for increasing trend). Similarly, AL increased among the foreign-born with earlier age at immigration. These trends were less pronounced among individuals ≥55 years of age. Similar patterns were observed across all Hispanic/Latino heritage groups ( P for interaction=0.5). Our findings support both a "healthy immigrant" pattern and a loss of health advantage over time among US Hispanics/Latinos of diverse heritages.

Surmounting the Tower of Babel: Monolingual and bilingual 2-year-olds' understanding of the nature of foreign language words.

PubMed

Byers-Heinlein, Krista; Chen, Ke Heng; Xu, Fei

2014-03-01

Languages function as independent and distinct conventional systems, and so each language uses different words to label the same objects. This study investigated whether 2-year-old children recognize that speakers of their native language and speakers of a foreign language do not share the same knowledge. Two groups of children unfamiliar with Mandarin were tested: monolingual English-learning children (n=24) and bilingual children learning English and another language (n=24). An English speaker taught children the novel label fep. On English mutual exclusivity trials, the speaker asked for the referent of a novel label (wug) in the presence of the fep and a novel object. Both monolingual and bilingual children disambiguated the reference of the novel word using a mutual exclusivity strategy, choosing the novel object rather than the fep. On similar trials with a Mandarin speaker, children were asked to find the referent of a novel Mandarin label kuò. Monolinguals again chose the novel object rather than the object with the English label fep, even though the Mandarin speaker had no access to conventional English words. Bilinguals did not respond systematically to the Mandarin speaker, suggesting that they had enhanced understanding of the Mandarin speaker's ignorance of English words. The results indicate that monolingual children initially expect words to be conventionally shared across all speakers-native and foreign. Early bilingual experience facilitates children's discovery of the nature of foreign language words. Copyright © 2013 Elsevier Inc. All rights reserved.

Detection of Foreign Matter in Transfusion Solution Based on Gaussian Background Modeling and an Optimized BP Neural Network

PubMed Central

Zhou, Fuqiang; Su, Zhen; Chai, Xinghua; Chen, Lipeng

2014-01-01

This paper proposes a new method to detect and identify foreign matter mixed in a plastic bottle filled with transfusion solution. A spin-stop mechanism and mixed illumination style are applied to obtain high contrast images between moving foreign matter and a static transfusion background. The Gaussian mixture model is used to model the complex background of the transfusion image and to extract moving objects. A set of features of moving objects are extracted and selected by the ReliefF algorithm, and optimal feature vectors are fed into the back propagation (BP) neural network to distinguish between foreign matter and bubbles. The mind evolutionary algorithm (MEA) is applied to optimize the connection weights and thresholds of the BP neural network to obtain a higher classification accuracy and faster convergence rate. Experimental results show that the proposed method can effectively detect visible foreign matter in 250-mL transfusion bottles. The misdetection rate and false alarm rate are low, and the detection accuracy and detection speed are satisfactory. PMID:25347581

Presentation and management of nasal foreign bodies at a tertiary children's hospital in an American metro area.

PubMed

Scholes, Melissa A; Jensen, Emily L

2016-09-01

To examine rates of otolaryngology intervention in children presenting to our emergency department with nasal foreign bodies, factors associated with otolaryngology involvement, rates of complications, and details on nasal button battery exposure. All patients presenting with a nasal foreign body to Children's Hospital Colorado from 2007 to 2012 were identified. Factors leading to referral to otolaryngology and operative intervention were examined, as well as complications. 102 patients were included. 36 (35%) patients were referred to the otolaryngology clinic, of which 58.9% required operating room intervention. 66 (64.7%) children had their nasal foreign bodies removed in the emergency room, however 30 (45%) of these were removed by an otolaryngology resident or attending physician. Overall, 64.7% of nasal foreign bodies required removal by otolaryngology. Of the 15 objects removed in the operating room, six were button batteries. No septal perforations occurred as a result of nasal button battery exposure. Multivariable logistic regression showed two significant predictors of OR removal: age and disc shaped objects. While emergency department providers are comfortable attempting removal of nasal foreign bodies, there was a high rate of otolaryngology intervention. Based on this data, there is a need to educate emergency room providers on nasal anatomy and techniques for nasal foreign body removal. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Optoacoustic multispectral imaging of radiolucent foreign bodies in tissue.

PubMed

Page, Leland; Maswadi, Saher; Glickman, Randolph D

2013-01-01

Optoacoustic imaging is an emerging medical technology that uniquely combines the absorption contrast of optical imaging and the penetration depth of ultrasound. While it is not currently employed as a clinical imaging modality, the results of current research strongly support the use of optoacoustic-based methods in medical imaging. One such application is the diagnosis of the presence of soft tissue foreign bodies. Because many radiolucent foreign bodies have sufficient contrast for imaging in the optical domain, laser-induced optoacoustic imaging could be advantageous for the detection of such objects. Common foreign bodies have been scanned over a range of visible and near infrared wavelengths by using an optoacoustic method to obtain the spectroscopic properties of the materials commonly associated with these foreign bodies. The derived optical absorption spectra compared quite closely to the absorption spectra generated when using a conventional spectrophotometer. By using the probe-beam deflection technique, a novel, pressure-wave detection method, we successfully generated optoacoustic spectroscopic plots of a wooden foreign body embedded in a tissue phantom, which closely resembled the spectrum of the same object obtained in isolation. A practical application of such spectra is to assemble a library of spectroscopic data for radiolucent materials, from which specific characteristic wavelengths can be selected for use in optimizing imaging instrumentation and provide a basis for the identification of the material properties of particular foreign bodies.

Comparing Subjective With Objective Sleep Parameters Via Multisensory Actigraphy in German Physical Education Students.

PubMed

Kölling, Sarah; Endler, Stefan; Ferrauti, Alexander; Meyer, Tim; Kellmann, Michael

2016-01-01

This study compared subjective with objective sleep parameters among 72 physical education students. Furthermore, the study determined whether 24-hr recording differs from nighttime recording only. Participants wore the SenseWear Armband™ for three consecutive nights and kept a sleep log. Agreement rates ranged from moderate to low for sleep onset latency (ICC = 0.39 to 0.70) and wake after sleep onset (ICC = 0.22 to 0.59), while time in bed (ICC = 0.93 to 0.95) and total sleep time (ICC = 0.90 to 0.92) revealed strong agreement during this period. Comparing deviations between 24-hr wearing time (n = 24) and night-only application (n = 20) revealed no statistical difference (p > 0.05). As athletic populations have yet to be investigated for these purposes, this study provides useful indicators and practical implications for future studies.

Multi-centre evaluation of two daily disposable contact lenses.

PubMed

Walker, Jon; Young, Graeme; Hunt, Chris; Henderson, Terri

2007-05-01

To evaluate the clinical performance of two daily disposable contact lenses: 1-DAY ACUVUE (1DA) (etafilcon A, Johnson & Johnson Vision Care) and FOCUS DAILIES with AquaComfort (FD) (nelfilcon A, CIBA Vision, Inc.), which contains a quickly released moisture enhancing agent, polyvinyl alcohol (PVA). This was a 1-week, daily wear, subject-masked, bilateral, parallel group study with subjects randomly assigned to one of two daily disposable soft contact lenses. Subjects were existing soft contact lens wearers in the age range 18-39 years with a spherical refraction between -0.50 and -6.00 D. Subjects were assessed at baseline and after 1 week. Assessments included both subjective (symptoms, wearing time, vision) and objective (lens fit and ocular health) outcomes. Twenty clinical sites enrolled 282 subjects (74% female) of whom 276 (98%) successfully completed the study. Significantly more 1DA wearers reported higher mean comfort scores than with FD (3.95 versus 3.41, respectively, P<0.0001). End-of-day comfort means were also significantly higher with the 1DA group compared to the FD group (3.3 versus 3.0, P=0.03). The 1DA group reported significantly longer mean overall wearing time (1DA was worn on average 0.66+/-0.30 h longer than FD, P=0.03) and longer mean comfortable wearing time (1DA was worn on average 1.73+/-0.35 h longer than FD, P<0.0001). The 1DA lens generally showed significantly better on-eye fitting in terms of movement in primary (P<0.0001) and upgaze (P<0.0001) and ease of removal from the eye (92% versus 63%, P<0.0001) compared to FD. There was significantly less corneal staining observed with the 1DA wearing eyes compared with the FD wearing eyes (23% versus 45%, respectively, P<0.0001). Finally, there was a weak correlation between corneal staining and comfort for FD (r=0.27, P=0.002, n=136), but not for 1DA (r=-0.11, P=0.18, n=140). Subjective and objective clinical performance differences between two commonly used daily disposable lenses highlight that, although both lenses may be considered as clinically acceptable, these lenses should not be regarded as interchangeable.

Magnetic resonance imaging metallic artifact of commonly encountered surgical implants and foreign material.

PubMed

Sutherland-Smith, James; Tilley, Brenda

2012-01-01

Magnetic resonance imaging (MRI) artifacts secondary to metallic implants and foreign bodies are well described. Herein, we provide quantitative data from veterinary implants including total hip arthroplasty implants, cranial cruciate repair implants, surgical screws, a skin staple, ligation clips, an identification microchip, ameroid constrictor, and potential foreign bodies including air gun and BB projectiles and a sewing needle. The objects were scanned in a gelatin phantom with plastic grid using standardized T2-weighted turbo-spin echo (TSE), T1-weighted spin echo, and T2*-weighted gradient recalled echo (GRE) image acquisitions at 1.5 T. Maximum linear dimensions and areas of signal voiding and grid distortion were calculated using a DICOM workstation for each sequence and object. Artifact severity was similar between the T2-weighted TSE and T1-weighted images, while the T2*-weighted images were most susceptible to artifact. Metal type influenced artifact size with the largest artifacts arising from steel objects followed by surgical stainless steel, titanium, and lead. For animals with metallic surgical implants or foreign bodies, the quantification of the artifact size will help guide clinicians on the viability of MRI. © 2012 Veterinary Radiology & Ultrasound.

Wear resistance and friction reduction in acrylo nitrile butadiene rubber through hybrid combination of graphite flakes and nano tungsten disulphide

NASA Astrophysics Data System (ADS)

Agrawal, Neha; Pandey, Akanksha; Parihar, A. S.; Mishra, A. K.; Gandhi, M. N.; Bhattacharyya, A. R.; Mukhopadhyay, K.; Prasad, N. E.

2016-05-01

Friction and wear have considerable role in the life span of two interacting parts. Incorporation of nanofillers in polymers/elastomers matrix causes commendable changes in its tribologicalproperties. The main purpose of this work is to reduce the coefficient of friction and wear rate of Acrylo Nitrile Butadiene rubber (NBR). To achieve such objective traditionally well knownlubricants graphite(G), tungsten disulphide (WS2) and there hybrid combination was incorporated in NBR matrix. Effect of applied load (force) and concentration of fillers on tribological properties of NBR had been studied. The filler incorporation enhanced the hardnessby 8%, showed resistance to hydraulic oil and aging effect also got improved significantly. A particular optimized concentration of NBR with hybrid combination of 2% WS2 and 4% Graphite showed minimum coefficient of friction as well as wear rate. A hypothesis could be attributed that similar lamellar structure of WS2 and Graphite along with formation of a stable nanoscale disulfide tribofilmcould result in lowering of friction. These substantially improved properties of nanoreinforced rubber materials would definitely pave promising path for plethora of potential technological applications.

Wear resistance and friction reduction in acrylo nitrile butadiene rubber through hybrid combination of graphite flakes and nano tungsten disulphide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agrawal, Neha, E-mail: neha87bhu@gmail.com; Indian Institute of Technology Bombay, Powai, Mumbai 400076, Maharashtra; Pandey, Akanksha

Friction and wear have considerable role in the life span of two interacting parts. Incorporation of nanofillers in polymers/elastomers matrix causes commendable changes in its tribologicalproperties. The main purpose of this work is to reduce the coefficient of friction and wear rate of Acrylo Nitrile Butadiene rubber (NBR). To achieve such objective traditionally well knownlubricants graphite(G), tungsten disulphide (WS{sub 2}) and there hybrid combination was incorporated in NBR matrix. Effect of applied load (force) and concentration of fillers on tribological properties of NBR had been studied. The filler incorporation enhanced the hardnessby 8%, showed resistance to hydraulic oil and agingmore » effect also got improved significantly. A particular optimized concentration of NBR with hybrid combination of 2% WS{sub 2} and 4% Graphite showed minimum coefficient of friction as well as wear rate. A hypothesis could be attributed that similar lamellar structure of WS{sub 2} and Graphite along with formation of a stable nanoscale disulfide tribofilmcould result in lowering of friction. These substantially improved properties of nanoreinforced rubber materials would definitely pave promising path for plethora of potential technological applications.« less

Development of a ceramic surface replacement for the hip. An experimental Sialon model.

PubMed

Clarke, I C; Phillips, W; McKellop, H; Coster, I R; Hedley, A; Amstutz, H C

1979-01-01

The objective of this study was to investigate the design and fixation advantages of Sialon ceramic surface replacements implanted without acrylic bone cement. The biocompatibility and friction and wear properties of Sialon ceramic were compared with more conventional prosthetic materials such as stainless steel and alumina. A functional load-bearing canine hip surface replacement model was established to test Sialon femoral cups designed for fixation by bone ingrowth. The results of the polyethylene wear tests on highly polished ceramic and stainless steel counterfaces were essentially similar. These laboratory data indicated that the in-vivo polyethylene wear performance on metal or ceramic prosthetic surfaces could be expected to be indistinguishable, i.e. the ceramic/polyethylene combination would not offer any improved wear resistance in-vivo. It was found possible to get bone ingrowth into the macrokeying areas of the ceramic femoral cups but not into the microporous surfaces due to the presence of a fibrous membrane lining their internal surfaces. The biocompatability specimens also appeared to be invested with a fibrous membrane. Further studies are under way to determine the relationship between reaming procedures, micro motion at the interfaces and Sialon biocompatibility.

Influence of Surface Features for Increased Heat Dissipation on Tool Wear

PubMed Central

Beno, Tomas; Hoier, Philipp; Wretland, Anders

2018-01-01

The critical problems faced during the machining process of heat resistant superalloys, (HRSA), is the concentration of heat in the cutting zone and the difficulty in dissipating it. The concentrated heat in the cutting zone has a negative influence on the tool life and surface quality of the machined surface, which in turn, contributes to higher manufacturing costs. This paper investigates improved heat dissipation from the cutting zone on the tool wear through surface features on the cutting tools. Firstly, the objective was to increase the available surface area in high temperature regions of the cutting tool. Secondly, multiple surface features were fabricated for the purpose of acting as channels in the rake face to create better access for the coolant to the proximity of the cutting edge. The purpose was thereby to improve the cooling of the cutting edge itself, which exhibits the highest temperature during machining. These modified inserts were experimentally investigated in face turning of Alloy 718 with high-pressure coolant. Overall results exhibited that surface featured inserts decreased flank wear, abrasion of the flank face, cutting edge deterioration and crater wear probably due to better heat dissipation from the cutting zone. PMID:29693579

Interaction Activities in the Foreign Classroom, or How to Grow a Tulip-Rose

ERIC Educational Resources Information Center

Paulston, Christina Bratt; Selekman, Howard R.

1976-01-01

A report is made on the use of foreign language for spontaneous communication in an elementary language class. Four correction-free, peer communicative/interaction activities are outlined according to procedures, objectives, and evaluations. (Author/RM)

Patient Compliance During Contact Lens Wear: Perceptions, Awareness, and Behavior

PubMed Central

Bui, Thai H.; Cavanagh, H. Dwight; Robertson, Danielle M.

2011-01-01

Objectives Patient noncompliance with recommended hygienic practices in contact lens wear is often considered a significant risk factor for microbial keratitis and adverse contact lens–related events. Despite advancements in lens materials and care solutions, noncompliant behavior continues to hinder efforts to maximize contact lens safety. The objective of this pilot study was to assess the relationship between perceived and actual compliance with awareness of risk and behavior. Methods One hundred sixty-two established contact lens wearers were sequentially evaluated after their routine contact lens examination at the Optometry Clinic at the University of Texas Southwestern Medical Center at Dallas, TX. Each patient was questioned by a single trained interviewer regarding his or her lens care practices and knowledge of risk factors associated with lens wear. Results Eighty-six percent of patients believed they were compliant with lens wear and care practices; 14% identified themselves as noncompliant. Using a scoring model, 32% demonstrated good compliance, 44% exhibited average compliance, and 24% were noncompliant; age was a significant factor (P = 0.020). Only 34% of patients who perceived themselves as compliant exhibited a good level of compliance (P<0.001). Eighty percent of patients reported an awareness of risk factors, but awareness did not influence negative behavior. Replacing the lens case was the only behavior associated with a positive history for having experienced a prior contact lens–related complication (P = 0.002). Conclusions Perceived compliance is not an indicator for appropriate patient behavior. A large proportion of patients remain noncompliant despite awareness of risk. Education alone is not a sufficient strategy to improve behavior; newer approaches aimed at improving compliance with lens care practices are urgently needed. PMID:20935569

Practices and Objectives in Training for Foreign Service. Report of the National Conference on Foreign Service Training, Washington, December 26, 1923. Bulletin, 1924, No. 21

ERIC Educational Resources Information Center

Swiggett, Glen Levin

1924-01-01

Eighteen States and the District of Columbia were represented at the second conference of collegiate instructors in foreign service training subjects, which was held at the New Willard Hotel, Washington, D.C., December 26, 1923, under the direction of the former advisory council and committee of fifteen on educational preparation for foreign…

Particle Disease: A Current Review of the Biological Mechanisms in Periprosthetic Osteolysis After Hip Arthroplasty

PubMed Central

Sukur, Erhan; Akman, Yunus Emre; Ozturkmen, Yusuf; Kucukdurmaz, Fatih

2016-01-01

Background: Inflammatory responses to wear debris cause osteolysis that leads to aseptic prosthesis loosening and hip arthroplasty failure. Although osteolysis is usually associated with aseptic loosening, it is rarely seen around stable implants. Aseptic implant loosening is a simple radiologic phenomenon, but a complex immunological process. Particulate debris produced by implants most commonly causes osteolysis, and this is called particle-associated periprosthetic osteolysis (PPO). Objective: The objective of this review is to outline the features of particle-associated periprosthetic osteolysis to allow the physician to recognise this condition and commence early treatment, thereby optimizing patient outcome. Methods: A thorough literature search was performed using available databases, including Pubmed, to cover important research published covering particle-associated PPO. Results: Although osteolysis causes bone resorption, clinical, animal, and in vitro studies of particle bioreactivity suggest that particle-associated PPO represents the culmination of several biological reactions of many cell types, rather than being caused solely by the osteoclasts. The biological activity is highly dependent on the characteristics and quantity of the wear particles. Conclusion: Despite advances in total hip arthroplasty (THA), particle-associated PPO and aseptic loosening continue to be major factors that affect prosthetic joint longevity. Biomarkers could be exploited as easy and objective diagnostic and prognostic targets that would enable testing for osteolysis after THA. Further research is needed to identify new biomarkers in PPO. A comprehensive understanding of the underlying biological mechanisms is crucial for developing new therapeutic interventions to reverse or suppress biological responses to wear particles. PMID:27499822

Predictors of recurrent ingestion of gastrointestinal foreign bodies

PubMed Central

Grimes, Ian C; Spier, Bret J; Swize, Lisa R; Lindstrom, Mary J; Pfau, Patrick R

2013-01-01

BACKGROUND: Gastrointestinal foreign bodies are commonly encountered; however, little knowledge exists as to the causes of foreign body ingestions and why they occur repeatedly in some patients. OBJECTIVE: To identify and define patients at high risk for recurrent foreign body ingestion. METHODS: A retrospective chart review of foreign body ingestion was conducted at a tertiary care medical centre over an 11-year period. Variables analyzed included age, sex, incarceration status, Diagnostic and Statistical Manual of Mental Disorders-IV diagnosis, success of endoscopy, type of sedation used, method of extraction, complications, presence of gastrointestinal pathology, and incidence of recurrent food impaction or foreign body. RESULTS: A total of 159 patients with a foreign body ingestion were identified. One hundred fourteen (77%) experienced a single episode of ingestion and 45 (23%) experienced multiple ingestions. Of the patients with multiple ingestions, 27 (60%) had recurrent food impactions while 18 (40%) ingested foreign objects. In the recurrent ingestor group, a psychiatric disorder had been diagnosed in 16 patients (35.6%) and there were 13 incarcerated individuals (28.9%). The average number of recurrences was 2.6 per patient (117 total recurrences). Individuals with a psychiatric disorder experienced 3.9 recurrences per patient, while prisoners averaged 4.1 recurrences per patient. The combination of a psychiatric disorder and being incarcerated was associated with the highest recurrence rate (4.33 per patient). Multivariable logistic regression revealed that male sex (OR 2.9; P=0.022), being incarcerated (OR 3.0; P=0.024) and the presence of a psychiatric disorder (OR 2.5; P=0.03) were risk factors for recurrent ingestion. CONCLUSION: Risk factors for recurrent ingestion of foreign bodies were male sex, being incarcerated and the presence of a psychiatric disorder. PMID:23378983

76 FR 25407 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-04

... INFORMATION CONTACT: Assistant Director, Compliance Outreach & Implementation, Office of Foreign Assets... their organizations on a worldwide basis with the objective of denying their businesses and agents... of the Central Intelligence Agency, the Director of the Federal Bureau of Investigation, the...

Microstructural Evolution of AlCoCrFeNiSi High-Entropy Alloy Powder during Mechanical Alloying and Its Coating Performance

PubMed Central

Fu, Ming; Xiong, Wei

2018-01-01

High-entropy alloys (HEAs) are promising structural materials due to their excellent comprehensive performances. The use of mechanically alloyed powders to deposit HEA coatings through atmospheric plasma spraying (APS) is an effective approach that can broaden the application areas of the HEAs. In this paper, a ductility–brittleness AlCoCrFeNiSi system was chosen as an object of study, and the detailed evolution of the surface morphology, particle size distribution, and microstructure of the powder during mechanical alloying was investigated. An AlCoCrFeNiSi HEA coating was deposited using powder milled for 10 h, which can be used as an ideal feedstock for APS. The surface morphology, microstructure, microhardness, and wear behavior of the coating at room temperature were investigated. The results showed that as the milling time increased, the particle size first increased, and then decreased. At the milling time of 10 h, simple body-centered cubic (BCC) and face-centered cubic (FCC) solid solution phases were formed. After spraying, the lamellar structure inside a single particle disappeared. An ordered BCC phase was detected, and the diffraction peaks of the Si element also disappeared, which indicates that phase transformation occurred during plasma spraying. A transmission electron microscopy analysis showed that nanometer crystalline grains with a grain size of about 30 nm existed in the APS coating. For the coating, an average microhardness of 612 ± 41 HV was obtained. Adhesive wear, tribo-oxidation wear, and slight abrasion wear took place during the wear test. The coating showed good wear resistance, with a volume wear rate of 0.38 ± 0.08 × 10−4 mm3·N−1·m−1, which makes it a promising coating for use in abrasive environments. PMID:29473872

Removal of impacted esophageal foreign bodies with a dual-channel endoscope: 19 cases

PubMed Central

WANG, CHANGXIONG; CHEN, PING

2013-01-01

There have been few reports concerning the endoscopic removal of impacted esophageal foreign bodies from patients. The objective of this study was to evaluate the effectiveness of dual-channel endoscopy in managing foreign-body ingestions in patients. A total of 19 patients with foreign-body ingestions between September 2008 and July 2011 were selected from the Digestive Endoscope Center in Lishui, a typical middle-sized city in China. The patients underwent endoscopy following admission. The impacted foreign bodies were successfully removed from 18 patients without complications using a dual-channel endoscope. One patient underwent surgery for an ingested denture following the failure of the endoscopic removal method. This study demonstrates that dual-channel endoscopic management may be a useful option for removing ingested foreign bodies from the esophagus. PMID:23935752

Influence of pH, bleaching agents, and acid etching on surface wear of bovine enamel

PubMed Central

Soares, Ana Flávia; Bombonatti, Juliana Fraga Soares; Alencar, Marina Studart; Consolmagno, Elaine Cristina; Honório, Heitor Marques; Mondelli, Rafael Francisco Lia

2016-01-01

ABSTRACT Development of new materials for tooth bleaching justifies the need for studies to evaluate the changes in the enamel surface caused by different bleaching protocols. Objective The aim of this study was to evaluate the bovine dental enamel wear in function of different bleaching gel protocols, acid etching and pH variation. Material and Methods Sixty fragments of bovine teeth were cut, obtaining a control and test areas. In the test area, one half received etching followed by a bleaching gel application, and the other half, only the bleaching gel. The fragments were randomly divided into six groups (n=10), each one received one bleaching session with five hydrogen peroxide gel applications of 8 min, activated with hybrid light, diode laser/blue LED (HL) or diode laser/violet LED (VHL) (experimental): Control (C); 35% Total Blanc Office (TBO35HL); 35% Lase Peroxide Sensy (LPS35HL); 25% Lase Peroxide Sensy II (LPS25HL); 15% Lase Peroxide Lite (LPL15HL); and 10% hydrogen peroxide (experimental) (EXP10VHL). pH values were determined by a pHmeter at the initial and final time periods. Specimens were stored, subjected to simulated brushing cycles, and the superficial wear was determined (μm). ANOVA and Tukey´s tests were applied (α=0.05). Results The pH showed a slight decrease, except for Group LPL15HL. Group LPS25HL showed the highest degree of wear, with and without etching. Conclusion There was a decrease from the initial to the final pH. Different bleaching gels were able to increase the surface wear values after simulated brushing. Acid etching before bleaching increased surface wear values in all groups. PMID:27008254

Effects of nitrogen ion implantation time on tungsten films deposited by DC magnetron sputtering on AISI 410 martensitic stainless steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malau, Viktor, E-mail: malau@ugm.ac.id; Ilman, Mochammad Noer, E-mail: noer-ilman@yahoo.com; Iswanto, Priyo Tri, E-mail: priyatri@yahoo.com

Nitrogen ion implantation time on tungsten thin film deposited on surface of AISI 410 steel has been performed. Tungsten thin film produced by dc magnetron sputtering method was deposited on AISI 410 martensitic stainless steel substrates, and then the nitrogen ions were implanted on tungsten thin film. The objective of this research is to investigate the effects of implantation deposition time on surface roughness, microhardness, specific wear and corrosion rate of nitrogen implanted on tungsten film. Magnetron sputtering process was performed by using plasma gas of argon (Ar) to bombardier tungsten target (W) in a vacuum chamber with a pressuremore » of 7.6 x 10{sup −2} torr, a voltage of 300 V, a sputter current of 80 mA for sputtered time of 10 minutes. Nitrogen implantation on tungsten film was done with an initial pressure of 3x10{sup −6} mbar, a fluence of 2 x 10{sup 17} ions/cm{sup 2}, an energy of 100 keV and implantation deposition times of 0, 20, 30 and 40 minutes. The surface roughness, microhardness, specific wear and corrosion rate of the films were evaluated by surfcorder test, Vickers microhardness test, wear test and potentiostat (galvanostat) test respectively. The results show that the nitrogen ions implanted deposition time on tungsten film can modify the surface roughness, microhardness, specific wear and corrosion rate. The minimum surface roughness, specific wear and corrosion rate can be obtained for implantation time of 20 minutes and the maximum microhardness of the film is 329 VHN (Vickers Hardness Number) for implantation time of 30 minutes. The specific wear and corrosion rate of the film depend directly on the surface roughness.« less

Quantification of wear-time adherence of removable appliances in young orthodontic patients in relation to their BMI: a preliminary study

PubMed Central

Schott, Timm Cornelius; Ludwig, Björn

2014-01-01

Purpose The relationship between unhealthy body mass index (BMI) and adherence to orthodontic treatment with removable appliances has not previously been evaluated. Objective The aim of this study was to quantify the association between BMI and wear time of removable orthodontic appliances and to evaluate BMI changes during orthodontic treatment. Patients and methods Fifty-three normal-weight and 39 overweight/obese children and adolescents (7–15 years old) undergoing orthodontic treatment with removable appliances were enrolled into the study. BMI categories were determined using standardized age-specific and sex-specific BMI criteria, using data measured at the beginning of therapy and once during orthodontic treatment. Wear times of removable appliances were measured at 15-minute intervals over a period of 5 months using implanted microelectronic sensors. Median wear-time values were used in the analysis with the Mann–Whitney U-test used to test statistical differences between groups. Results The median wear time of removable orthodontic appliances was 9.3 hours for normal-weight patients and 9.2 hours for overweight/obese patients. No statistically significant (P>0.05) or clinically relevant differences in usage or adherence were detected between normal-weight and overweight/obese patients. BMI did not influence wear time or behavior of removable orthodontic appliances by young patients. The majority of patients showed qualitative decreases in BMI during therapy. Conclusion The orthodontic treatment of young patients with removable devices does not require BMI-dependent changes in the treatment strategy. However, the use of removable appliances during meal times raises the possibility of reducing food intake, and in this way the orthodontist may have an active role to play in weight reduction. PMID:25484576

A simple method of measuring the wear of explanted acetabular component inserts

PubMed Central

Krakow, L.; Klockow, A.; Roehner, E.; Brodt, S.; Eijer, H.; Bossert, J.

2017-01-01

Objectives The determination of the volumetric polyethylene wear on explanted material requires complicated equipment, which is not available in many research institutions. Our aim in this study was to present and validate a method that only requires a set of polyetheretherketone balls and a laboratory balance to determine wear. Methods The insert to be measured was placed on a balance, and a ball of the appropriate diameter was inserted. The cavity remaining between the ball and insert caused by wear was filled with contrast medium and the weight of the contrast medium was recorded. The volume was calculated from the known density of the liquid. The precision, inter- and intraobserver reliability, were determined by four investigators on four days using nine inserts with specified wear (0.094 ml to 1.626 ml), and the intra-class correlation coefficient was calculated. The feasibility of using this method in routine clinical practice and the time required for measurement were tested on 84 explanted inserts by one investigator. Results In order to get the mean for all investigators and determinations, the deviation between the measured and specified wear was -0.08 ml (sd 0.12; -0.21 to 0.11). The interobserver reliability was 0.989 ml (95% confidence interval (CI) 0.964 to 0.997) and the intraobserver reliability was 0.941 for observer 1 (95% CI 0.846 to 0.985), 0.983 for observer 2 (95% CI 0.956 to 0.995), 0.939 for observer 3 (95% CI 0.855 to 0.984), and 0.934 for observer 4 (95% CI 0.790 to 0.984). The mean time required to examine the samples was two minutes (sd 2; 1 to 5). Conclusion The method presented here was shown to be sufficiently precise for many settings and is a cost-effective and quick method of determining the volumetric wear of explanted acetabular components. However, the measurement of wear for scientific purposes will probably continue to involve more accurate and dedicated laboratory equipment. Cite this article: L. Krakow, A. Klockow, E. Roehner, S. Brodt, H. Eijer, J. Bossert, G. Matziolis. A simple method of measuring the wear of explanted acetabular component inserts. Bone Joint Res 2017;6:530–534. DOI: 10.1302/2046-3758.69.BJR-2016-0249.R1 PMID:28899855

Limits of Stability and Adaptation to Wearing Rocker Bottom Shoes.

PubMed

Vieira, Edgar Ramos; Guerrero, Gerardo; Holt, Daniel; Arreaza, Monica; Veroes, Valentina; Brunt, Denis

2014-06-01

Stability and balance are fundamental during static and dynamic activities. The effects of wearing rocker bottom sole (RBS) shoes on the limits of stability (LOS) and adaptation to wearing RBS shoes need to be investigated. The objectives of this study were to evaluate the LOS when wearing RBS shoes, and to evaluate if people improve their stability while wearing RBS shoes over time. Eleven female subjects with no lower extremity impairments participated in the study. The LOS were tested at baseline and weeks 3 and 6 using a Neurocom SMART EquiTest equipment. Center of pressure (CoP) was determined using force plates, and the center of gravity (CoG) position was estimated from the CoP measures and subjects' anthropometry. Subjects performed a series of tasks that involved leaning in different directions so as to move the vertical projection of their CoG. End-point excursions of the CoG floor projection were calculated as a percentage of the distance between the starting position and the target. Considering the body as an inverted pendulum, we recorded the average angular velocity of the inverted pendulum during the movements and quantified directional control as a percentage of movement toward versus away from the target. Shoe types were compared using paired t tests, and sessions were compared using repeated measures ANOVA. The angular velocities of the inverted pendulum (ie, CoG velocity) were not significantly different between shoe conditions in the front and back directions at baseline (4 ± 3 with RBS vs 5 ± 2 deg/sec with regular shoes, and 4 ± 1 vs 6 ± 4 deg/sec). Front directional control of the CoG was significantly worse with RBS shoes at weeks 3 and 6 ( P < .015). Front end-point excursions were also lower with RBS shoes both at baseline and week 6 ( P < .014). There were no significant changes over time. The findings indicate that the LOS were negatively affected by wearing RBS shoes and that people do not improve their stability while wearing these shoes even after a 6-week period of use. This study shows that wearing RBS shoes increase instability and the instability remains even after wearing these shoes for six weeks.

Food choking hazards in children.

PubMed

Sidell, Douglas R; Kim, Irene A; Coker, Tumaini R; Moreno, Candice; Shapiro, Nina L

2013-12-01

To review the literature on pediatric food choking risks, with the long-term goal of supporting legislation regulating the production, labeling, and distribution of high-risk foods. A PubMed search (Keywords: choking, obstruction, asphyxiation, foreign body, food) was conducted in July-September 2010 with publication dates ranging from 1966 to 2010. Articles related to pediatric foreign body aspiration (FBA) were selected by three independent reviewers. 1145 articles were initially identified. Abstracts were then screened utilizing a tool designed to isolate relevant pediatric choking events; this tool helped to only select abstracts which presented data on patients younger than 18 years of age who had choked on food items. Through this, a total of 72 pertinent articles were isolated (55 observational studies, 17 case reports/series). For each study, patient age, sex, foreign body location, presenting signs and symptoms, utility of radiographic studies, and type of foreign body detected in the majority of study participants were determined. A "majority" of patients for each study was predetermined arbitrarily to be 2/3 of the studied population. The majority of patients in each observational study was determined to be: male (87% of all studies) and age <5 years (95% of all studies). Aspirated foreign bodies were mostly detected in the right main bronchus foreign body (72% of all studies), and there were abnormal radiographic signs (81% of all studies) at the time of evaluation. Food-object foreign bodies were the most frequent factors associated with choking (94% of all studies). Childhood aspiration of food-objects is a significant public health issue. Although there is substantial legislation regulating non-food items that pose a choking hazard, equivalent guidelines do not exist for high-risk foods. Our study identifies and confirms several risk factors for pediatric FBA events. In doing so, it echoes the concerns and suggestions of various groups in supporting the development of legislation which may reduce the incidence of food-object aspiration. Copyright © 2013. Published by Elsevier Ireland Ltd.

Prediction of the wear and evolution of cutting tools in a carbide / titanium-aluminum-vanadium machining tribosystem by volumetric tool wear characterization and modeling

NASA Astrophysics Data System (ADS)

Kuttolamadom, Mathew Abraham

The objective of this research work is to create a comprehensive microstructural wear mechanism-based predictive model of tool wear in the tungsten carbide / Ti-6Al-4V machining tribosystem, and to develop a new topology characterization method for worn cutting tools in order to validate the model predictions. This is accomplished by blending first principle wear mechanism models using a weighting scheme derived from scanning electron microscopy (SEM) imaging and energy dispersive x-ray spectroscopy (EDS) analysis of tools worn under different operational conditions. In addition, the topology of worn tools is characterized through scanning by white light interferometry (WLI), and then application of an algorithm to stitch and solidify data sets to calculate the volume of the tool worn away. The methodology was to first combine and weight dominant microstructural wear mechanism models, to be able to effectively predict the tool volume worn away. Then, by developing a new metrology method for accurately quantifying the bulk-3D wear, the model-predicted wear was validated against worn tool volumes obtained from corresponding machining experiments. On analyzing worn crater faces using SEM/EDS, adhesion was found dominant at lower surface speeds, while dissolution wear dominated with increasing speeds -- this is in conformance with the lower relative surface speed requirement for micro welds to form and rupture, essentially defining the mechanical load limit of the tool material. It also conforms to the known dominance of high temperature-controlled wear mechanisms with increasing surface speed, which is known to exponentially increase temperatures especially when machining Ti-6Al-4V due to its low thermal conductivity. Thus, straight tungsten carbide wear when machining Ti-6Al-4V is mechanically-driven at low surface speeds and thermally-driven at high surface speeds. Further, at high surface speeds, craters were formed due to carbon diffusing to the tool surface and being carried away by the rubbing action of the chips -- this left behind a smooth crater surface predominantly of tungsten and cobalt as observed from EDS analysis. Also, at high surface speeds, carbon from the tool was found diffused into the adhered titanium layer to form a titanium carbide (TiC) boundary layer -- this was observed as instances of TiC build-up on the tool edge from EDS analysis. A complex wear mechanism interaction was thus observed, i.e., titanium adhered on top of an earlier worn out crater trough, additional carbon diffused into this adhered titanium layer to create a more stable boundary layer (which could limit diffusion-rates on saturation), and then all were further worn away by dissolution wear as temperatures increased. At low and medium feeds, notch discoloration was observed -- this was detected to be carbon from EDS analysis, suggesting that it was deposited from the edges of the passing chips. Mapping the dominant wear mechanisms showed the increasing dominance of dissolution wear relative to adhesion, with increasing grain size -- this is because a 13% larger sub-micron grain results in a larger surface area of cobalt exposed to chemical action. On the macro-scale, wear quantification through topology characterization elevated wear from a 1D to 3D concept. From investigation, a second order dependence of volumetric tool wear (VTW) and VTW rate with the material removal rate (MRR) emerged, suggesting that MRR is a more consistent wear-controlling factor instead of the traditionally used cutting speed. A predictive model for VTW was developed which showed its exponential dependence with workpiece stock volume removed. Also, both VTW and VTW rate were found to be dependent on the accumulated cumulative wear on the tool. Further, a ratio metric of stock material removed to tool volume lost is now possible as a tool efficiency quantifier and energy-based productivity parameter, which was found to inversely depend on MRR - this led to a more comprehensive tool wear definition based on cutting tool efficiency. (Abstract shortened by UMI.)

Cross-sectional study examining four types of male penile and urethral "play".

PubMed

Rinard, Katherine; Nelius, Thomas; Hogan, LaMicha; Young, Cathy; Roberts, Alden E; Armstrong, Myrna L

2010-12-01

To provide further quantitative and qualitative evidence about men who insert foreign liquids and objects into their penis and/or urethra. As part of a larger, cross-sectional study examining men (n = 445) with genital piercings (GP), 2 questions inquired whether the respondents had penile tattoos and/or inserted other materials, such as fluids and foreign objects, into their penis and urethra. Four different practices have been described in the literature: embedding (a) foreign objects and/or (b) liquids subcutaneously into penile tissue, as well as inserting (c) liquids and/or (d) foreign objects into the urethra. In our study, 354 (78%) men with GP responded to the 2 questions; 85 (24%) replied affirmatively and 68 (80%) provided comments. Respondents coined their practices penile and/or urethral "play." Two respondents embedded metal balls into their penis, 1 at age 13 injected water for penis enlargement; 11 inserted liquids into the urethra, and 63 reported insertion of 32 different objects, frequently urethral sounds or "sounding" (n = 33/52%) were mentioned. Major motivation themes focused on sexual stimulation and experimentation. Penile tattoos (n = 14) were also reported, mainly for esthetics. Few complications or STDs were reported. Basic demographic assumptions of those who participate in these actions were challenged, and this study provides evidence of a wider distribution of men using penile or urethral play, and "sounding." Clinician awareness of these practices are important to obtain accurate health histories, manage genitourinary tract complications, as well as provide applicable patient education. Copyright © 2010 Elsevier Inc. All rights reserved.

Foreign Object Debris: FOD Prevention QS210LSK-REV

NASA Technical Reports Server (NTRS)

Randolph, Sherry; Seaman, John

2004-01-01

Housekeeping in the space industry? You may think the idea isn't technical enough for the shuttle program. Yet, eliminating Foreign Object Debris or FOD is an important goal for USA and NASA. The justification for this effort is based on data from the aeronautics industry. Experience has shown that if debris is not controlled, it may later cause a variety of in-flight issues. FOD can result in material damage, or make systems and equipment inoperable unsafe, or less efficient

An Analysis of the Twenty-One Missions of the Marine Corps Expeditionary Unit (Special Operations Capable)

DTIC Science & Technology

1994-06-03

unconventional warfare capability, consist of Army Special Forces and certain Navy, Air Force, and Marine Corps units as assigned. 4. Foreign ;ntgnal Pef~nse (JCS...7. Psychological Operations (JC5 Pub J-Q2): Planned operations to convey selected information and indicators to foreign audiences to influence their...emotions, motives, objective reasoning, and ultimately, the behavior of foreign governments, organizations groups, and individuals. The purpose of

Foreign bodies in a pediatric emergency department in South Africa.

PubMed

Timmers, Maarten; Snoek, Kitty G; Gregori, Dario; Felix, Janine F; van Dijk, Monique; van As, Sebastian A B

2012-12-01

Foreign body-related pediatric trauma has a high incidence, but studies with large data sets are rare and typically stem from Western settings. The aim of this study was to identify characteristics of foreign body-related trauma in children treated at our trauma unit in South Africa. In this retrospective study, we analyzed all foreign body-related trauma admissions from 1991 to 2009. We collected detailed data including age, sex, type of foreign body, injury severity, and anatomical location of the foreign body. We analysed 8149 cases. Marginally more boys (54.9%) than girls were involved. The overall median age was 3 years (interquartile range, 2-6 years); 78.8% were younger than 7 years. The predominant anatomical sites were the respiratory tract and the gastrointestinal tract (39.1%); ears (23.9%); nose (19.4%); and extremities (8.8%). The commonest objects were coins (20.8 %), (parts of) jewelry (9.5%), and food (8.7%). Three quarters (74.5%) of patients presented between 1 and 2 hours after the injury (median, 1 hour). A total of 164 cases (2.0%) were marked as possible child abuse; 17 cases were filed as confirmed child abuse. Preventive parent education programs targeting foreign body-related injury should mainly focus on both sexes younger than 7 years. Parents should be taught to keep small objects out of reach of young children, especially coins, because these most often result in a trauma unit visit.

Double gloving to reduce surgical cross-infection.

PubMed

Tanner, J; Parkinson, H

2002-01-01

The invasive nature of surgery, with its increased exposure to blood, means that during surgery there is a high risk of transfer of pathogens. Pathogens can be transferred through contact between surgical patients and the surgical team, resulting in post-operative or blood borne infections in patients or blood borne infections in the surgical team. Both patients and the surgical team need to be protected from this risk. This risk can be reduced by implementing protective barriers such as wearing surgical gloves. Wearing two pairs of surgical gloves, as opposed to one pair, is considered to provide an additional barrier and further reduce the risk of contamination. The primary objective of this review was to determine if double gloving (wearing two pairs of gloves), rather than single gloving, reduces the number of post-operative or blood borne infections in surgical patients or blood borne infections in the surgical team. The secondary objective of this review was to determine if double gloving, rather than single gloving, reduces the number of perforations to the innermost pair of surgical gloves. The innermost gloves (next to skin) compared with the outermost gloves are considered to be the last barrier between the patient and the surgical team. The reviewers searched the Cochrane Wounds Group Specialised Trials Register, MEDLINE, CINAHL, EMBASE and the Cochrane Controlled Trials Register. Glove manufacturing companies and professional organisations were also contacted. Randomised controlled trials involving: single gloving, double gloving, glove liners or coloured puncture indicator systems. Both reviewers independently assessed the relevance and quality of each trial. Trials to be included were cross checked and authenticated by both reviewers. Data was extracted by one reviewer and cross checked for accuracy by the second reviewer. Two trials were found which addressed the primary outcome. A total of 18 randomised controlled trials which measured glove perforations were identified and included in the review. DOUBLE GLOVING (wearing two pairs of latex gloves). Nine trials compared single latex gloves versus double latex gloves. These found no difference in the number of perforations between the single latex gloves and the outermost pair of the double latex gloves, but the number of perforations to the double latex-innermost glove was significantly reduced when two pairs of latex gloves were worn. ORTHOPAEDIC GLOVES (thicker than standard latex gloves). One trial compared single latex orthopaedic gloves with double latex gloves. This showed there was no difference in the number of perforations to the innermost gloves when wearing double latex gloves compared with a single pair of latex orthopaedic gloves. INDICATOR GLOVES (coloured latex gloves worn underneath latex gloves). Three trials compared double latex gloves versus double latex indicator gloves. These trials showed similar numbers of perforations to both the innermost and the outermost gloves for both gloving groups. Perforations to the outermost gloves were detected more easily when double latex indicator gloves were worn. Wearing double latex indicator gloves did not increase the detection of perforations to the innermost gloves. GLOVE LINERS (an insert worn between two pairs of latex gloves). Two trials compared double latex gloves versus double latex gloves with liners. These trials showed a significant reduction in the number of perforations to the innermost glove when a glove liner was worn between two pairs of latex gloves. CLOTH GLOVES (cloth gloves worn on top of latex gloves). Two trials compared double latex gloves versus latex inner with cloth outer gloves. These trials showed that wearing a cloth outer glove significantly reduced the number of perforations to the innermost latex glove. STEEL WEAVE GLOVES (steel weave gloves worn on top of latex gloves). One trial compared double latex gloves versus latex inner with steel weave outer gloves. This trial showed no reduction in the number of perforations to the innermost glove when wearing a steel weave outer glove. Wearing two pairs of latex gloves significantly reduces the number of perforations to the innermost glove. This evidence comes from trials undertaken in 'low risk' surgical specialties, that is specialties which did not include orthopaedic joint surgery. Wearing two pairs of latex gloves does not cause the glove wearer to sustain more perforations to their outermost glove. Wearing double latex indicator gloves enables the glove wearer to detect perforations to the outermost glove more easily than when wearing double latex gloves. However wearing a double latex indicator system will not assist with the detection of perforations to the innermost glove, nor reduce the number of perforations to either the outermost or the innermost glove. Wearing a glove liner between two pairs of latex gloves to undertake joint replacement surgery significantly reduces the number of perforations to the innermost glove compared with double latex gloves only. Wearing cloth outer gloves to undertake joint replacement surgery significantly reduces the number of perforations to the innermost glove compared with wearing double latex gloves. Wearing steel weave outer gloves to undertake joint replacement surgery does not reduce the number of perforations to innermost gloves compared with double latex gloves.

Eye problems in mountain and remote areas: prevention and onsite treatment--official recommendations of the International Commission for Mountain Emergency Medicine ICAR MEDCOM.

PubMed

Ellerton, John A; Zuljan, Igor; Agazzi, Giancelso; Boyd, Jeffrey J

2009-01-01

Although eyes are not frequently injured in the mountains, they are exposed to many adverse factors from the environment. This article, intended for first responders, paramedics, physicians, and mountaineers, is the consensus opinion of the International Commission for Mountain Emergency Medicine (ICAR-MEDCOM). Its aim is to give practical advice on the management of eye problems in mountainous and remote areas. Snow blindness and minor injuries, such as conjunctival and corneal foreign bodies, could immobilize a person and put him or her at risk of other injuries. Blunt or penetrating trauma can result in the loss of sight in the eye; this may be preventable if the injury is managed properly. In almost all cases of severe eye trauma, protecting the eye and arranging an immediate evacuation are necessary. The most common eye problems, however, are due to ultraviolet light and high altitude. People wearing contact lenses and with previous history of eye diseases are more vulnerable. Any sight-threatening eye problem or unexplained visual loss at high altitude necessitates descent. Wearing appropriate eye protection, such as sunglasses with sidepieces and goggles with polarized or photochromic lenses, could prevent most of the common eye problems in mountaineering.

[Profile of medical students from the Universidade Estadual Paulista-UNESP--Botucatu, who wear contact lenses].

PubMed

Vidotti, Vanessa Gonçalves; Kamegasawa, Amélia

2006-01-01

To analyze the ametropy, way of acquisition, the care and complications related to contact lens wear among medical students from Faculdade de Medicina de Botucatu da Universidade Estadual Paulista-UNESP--Botucatu (SP). Questionnaire applied to students from the 1st to the 6th year of the Medical school of the Faculdade de Medicina de Botucatu da Universidade Estadual Paulista-UNESP--Botucatu (SP), forming an analytical cross-sectional survey. 27.4% of the students use contact lenses, and among them 94.8% use soft contact lenses and 98% have negative degree. 46.9% discard their contact lens monthly. 63.9% have an average daily use of 14 hours, 14.1% acquire the contact lenses from optician stores or at pharmacies and 46.5% of the students clean their contact lenses when they put them on and take them off. Regarding complications, 51.0% reported ocular redness; 44.5%, blurred vision; and 42.6%, foreign body sensation, whereas only 4 students reported "keratitis". We concluded that the inadequate adaptation that occurs even in users knowledgeable about this issue such as medical students, has increased the risk of complications. This fact indicates that more attention must be paid to contact lens care in order to prevent permanent visual deficit.

75 FR 14255 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-24

... FURTHER INFORMATION CONTACT: Assistant Director, Compliance Outreach & Implementation, Office of Foreign... worldwide basis, with the objective of denying their businesses and agents access to the U.S. financial... Secretary of the Treasury consults with the Attorney General, the Director of the Central Intelligence...

75 FR 36474 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-25

... FURTHER INFORMATION CONTACT: Assistant Director, Compliance Outreach & Implementation, Office of Foreign... worldwide basis, with the objective of denying their businesses and agents access to the U.S. financial... Secretary of the Treasury consults with the Attorney General, the Director of the Central Intelligence...

14 CFR 33.77 - Foreign object ingestion-ice.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 33.77 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Design and Construction; Turbine Aircraft Engines § 33.77 Foreign... this section may not— (1) Cause a sustained power or thrust loss; or (2) Require the engine to be...

14 CFR 33.77 - Foreign object ingestion-ice.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 33.77 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Design and Construction; Turbine Aircraft Engines § 33.77 Foreign... this section may not— (1) Cause a sustained power or thrust loss; or (2) Require the engine to be...

Bacterial adhesion to unworn and worn silicone hydrogel lenses.

PubMed

Vijay, Ajay Kumar; Zhu, Hua; Ozkan, Jerome; Wu, Duojia; Masoudi, Simin; Bandara, Rani; Borazjani, Roya N; Willcox, Mark D P

2012-08-01

The objective of this study was to determine the bacterial adhesion to various silicone hydrogel lens materials and to determine whether lens wear modulated adhesion. Bacterial adhesion (total and viable cells) of Staphylococcus aureus (31, 38, and ATCC 6538) and Pseudomonas aeruginosa (6294, 6206, and GSU-3) to 10 commercially available different unworn and worn silicone hydrogel lenses was measured. Results of adhesion were correlated to polymer and surface properties of contact lenses. S. aureus adhesion to unworn lenses ranged from 2.8 × 10 to 4.4 × 10 colony forming units per lens. The highest adhesion was to lotrafilcon A lenses, and the lowest adhesion was to asmofilcon A lenses. P. aeruginosa adhesion to unworn lenses ranged from 8.9 × 10 to 3.2 × 10 colony forming units per lens. The highest adhesion was to comfilcon A lenses, and the lowest adhesion was to asmofilcon A and balafilcon A lenses. Lens wear altered bacterial adhesion, but the effect was specific to lens and strain type. Adhesion of bacteria, regardless of genera/species or lens wear, was generally correlated with the hydrophobicity of the lens; the less hydrophobic the lens surface, the greater the adhesion. P. aeruginosa adhered in higher numbers to lenses in comparison with S. aureus strains, regardless of the lens type or lens wear. The effect of lens wear was specific to strain and lens. Hydrophobicity of the silicone hydrogel lens surface influenced the adhesion of bacterial cells.

A penal problem: the increasing incidence of implantation of penile foreign bodies.

PubMed

Flynn, Ryan M; Mostafa, Hesham I; Khan, Omar A; Haselhuhn, Gregory D; Jain, Samay

2014-12-01

Our objective is to describe a novel presentation of subcutaneous penile insertion of foreign bodies. This is a practice performed globally and mostly has been reported outside of the United States. We present three cases of incarcerated males that implanted sculpted dominos into the penile subcutaneous tissue. The patients presented with erosion of the foreign bodies through the skin without evidence of infection. We believe that insertion of foreign bodies into penile subcutaneous tissue by incarcerated American males for sexual enhancement is more widespread than previously reported. Erosion is a novel presentation.

Review of foreign body ingestion and esophageal food impaction management in adolescents.

PubMed

Sahn, Benjamin; Mamula, Petar; Ford, Carol A

2014-08-01

Foreign body ingestion is a common clinical scenario among patients of all ages. The immediate risk to the patient ranges from negligible to life threatening. Initial and follow-up management strategies depend on multiple patient and ingested object-related factors. Available literature on this topic tends to focus on the small child or adult, leaving the clinician caring for adolescents to extrapolate this information to guide decision making for individual patients. This article reviews foreign body ingestion literature with important implications to the adolescent patient and raises awareness of some highly dangerous objects such as large button batteries, high-powered magnets, long sharps, narcotic packages, and super absorbent objects. An additional focus includes the management of esophageal food impaction. We highlight the unique aspects to the care of the adolescent with intentional ingestion and co-morbid psychiatric illness. The article concludes by discussing the challenges to prevention of ingestion in the at-risk patient. Copyright © 2014 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Towards Robust Designs Via Multiple-Objective Optimization Methods

NASA Technical Reports Server (NTRS)

Man Mohan, Rai

2006-01-01

Fabricating and operating complex systems involves dealing with uncertainty in the relevant variables. In the case of aircraft, flow conditions are subject to change during operation. Efficiency and engine noise may be different from the expected values because of manufacturing tolerances and normal wear and tear. Engine components may have a shorter life than expected because of manufacturing tolerances. In spite of the important effect of operating- and manufacturing-uncertainty on the performance and expected life of the component or system, traditional aerodynamic shape optimization has focused on obtaining the best design given a set of deterministic flow conditions. Clearly it is important to both maintain near-optimal performance levels at off-design operating conditions, and, ensure that performance does not degrade appreciably when the component shape differs from the optimal shape due to manufacturing tolerances and normal wear and tear. These requirements naturally lead to the idea of robust optimal design wherein the concept of robustness to various perturbations is built into the design optimization procedure. The basic ideas involved in robust optimal design will be included in this lecture. The imposition of the additional requirement of robustness results in a multiple-objective optimization problem requiring appropriate solution procedures. Typically the costs associated with multiple-objective optimization are substantial. Therefore efficient multiple-objective optimization procedures are crucial to the rapid deployment of the principles of robust design in industry. Hence the companion set of lecture notes (Single- and Multiple-Objective Optimization with Differential Evolution and Neural Networks ) deals with methodology for solving multiple-objective Optimization problems efficiently, reliably and with little user intervention. Applications of the methodologies presented in the companion lecture to robust design will be included here. The evolutionary method (DE) is first used to solve a relatively difficult problem in extended surface heat transfer wherein optimal fin geometries are obtained for different safe operating base temperatures. The objective of maximizing the safe operating base temperature range is in direct conflict with the objective of maximizing fin heat transfer. This problem is a good example of achieving robustness in the context of changing operating conditions. The evolutionary method is then used to design a turbine airfoil; the two objectives being reduced sensitivity of the pressure distribution to small changes in the airfoil shape and the maximization of the trailing edge wedge angle with the consequent increase in airfoil thickness and strength. This is a relevant example of achieving robustness to manufacturing tolerances and wear and tear in the presence of other objectives.

76 FR 23644 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-27

...: Assistant Director, Compliance Outreach & Implementation, Office of Foreign Assets Control, Department of... objective of denying their businesses and agents access to the U.S. financial system and the benefits of... the Attorney General, the Director of the Central Intelligence Agency, the Director of the Federal...

A Guide to Curriculum Planning in Foreign Language.

ERIC Educational Resources Information Center

Wisconsin State Dept. of Public Instruction, Madison.

A guide designed to help local curriculum planners develop and implement curriculums to provide all students with equal access to foreign languages provides an overview of current philosophies, objectives, methods, materials, and equipment and a guide to sequential program development, articulation, and evaluation. An introductory section…

Towards the optimal design of an uncemented acetabular component using genetic algorithms

NASA Astrophysics Data System (ADS)

Ghosh, Rajesh; Pratihar, Dilip Kumar; Gupta, Sanjay

2015-12-01

Aseptic loosening of the acetabular component (hemispherical socket of the pelvic bone) has been mainly attributed to bone resorption and excessive generation of wear particle debris. The aim of this study was to determine optimal design parameters for the acetabular component that would minimize bone resorption and volumetric wear. Three-dimensional finite element models of intact and implanted pelvises were developed using data from computed tomography scans. A multi-objective optimization problem was formulated and solved using a genetic algorithm. A combination of suitable implant material and corresponding set of optimal thicknesses of the component was obtained from the Pareto-optimal front of solutions. The ultra-high-molecular-weight polyethylene (UHMWPE) component generated considerably greater volumetric wear but lower bone density loss compared to carbon-fibre reinforced polyetheretherketone (CFR-PEEK) and ceramic. CFR-PEEK was located in the range between ceramic and UHMWPE. Although ceramic appeared to be a viable alternative to cobalt-chromium-molybdenum alloy, CFR-PEEK seems to be the most promising alternative material.

Surface Roughness Model Based on Force Sensors for the Prediction of the Tool Wear

PubMed Central

de Agustina, Beatriz; Rubio, Eva María; Sebastián, Miguel Ángel

2014-01-01

In this study, a methodology has been developed with the objective of evaluating the surface roughness obtained during turning processes by measuring the signals detected by a force sensor under the same cutting conditions. In this way, the surface quality achieved along the process is correlated to several parameters of the cutting forces (thrust forces, feed forces and cutting forces), so the effect that the tool wear causes on the surface roughness is evaluated. In a first step, the best cutting conditions (cutting parameters and radius of tool) for a certain quality surface requirement were found for pieces of UNS A97075. Next, with this selection a model of surface roughness based on the cutting forces was developed for different states of wear that simulate the behaviour of the tool throughout its life. The validation of this model reveals that it was effective for approximately 70% of the surface roughness values obtained. PMID:24714391

Application of powder metallurgy techniques to produce improved bearing elements for liquid rocket engines

NASA Technical Reports Server (NTRS)

Moracz, D. J.; Shipley, R. J.; Moxson, V. S.; Killman, R. J.; Munson, H. E.

1992-01-01

The objective was to apply powder metallurgy techniques for the production of improved bearing elements, specifically balls and races, for advanced cryogenic turbopump bearings. The materials and fabrication techniques evaluated were judged on the basis of their ability to improve fatigue life, wear resistance, and corrosion resistance of Space Shuttle Main Engine (SSME) propellant bearings over the currently used 440C. An extensive list of candidate bearing alloys in five different categories was considered: tool/die steels, through hardened stainless steels, cobalt-base alloys, and gear steels. Testing of alloys for final consideration included hardness, rolling contact fatigue, cross cylinder wear, elevated temperature wear, room and cryogenic fracture toughness, stress corrosion cracking, and five-ball (rolling-sliding element) testing. Results of the program indicated two alloys that showed promise for improved bearing elements. These alloys were MRC-2001 and X-405. 57mm bearings were fabricated from the MRC-2001 alloy for further actual hardware rig testing by NASA-MSFC.

Recoupment of Transportation Costs Incurred on Foreign Military Sales Cases

DTIC Science & Technology

1990-02-23

We are providing this final report on the Audit of Recoupment of Transportation Costs Incurred on Foreign Military Sales (FMS) Cases for your review...and comment. The audit was made during the period December 1988 through March 1989. The primary objectives of the audit were to determine whether...subject area. During FY’s 1987 and 1988, FMS transportation billings to foreign customers amounted to $30.5 million. The audit showed that basic procedures

The Educational Philosophy and Development Direction of School of Foreign Studies in Engineering Colleges in China: A Case Study of North China University of Water Resources and Electric Power (NCWU)

ERIC Educational Resources Information Center

Xinqiang, Wei

2012-01-01

This paper gives a brief analysis on the educational advantages and objects of NCWU. It believes that the educational philosophy and development direction of foreign school in engineering colleges must be set up on the basis of need of China and talents need, moreover, the development of the School of Foreign Studies must be analyzed by…

15 CFR 930.120 - Objectives.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Objectives. 930.120 Section 930.120... AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE OCEAN AND COASTAL RESOURCE MANAGEMENT FEDERAL... Objectives of the Act and National Security Interests § 930.120 Objectives. This subpart sets forth the...

Inflammatory response against different carbon fiber-reinforced PEEK wear particles compared with UHMWPE in vivo.

PubMed

Utzschneider, Sandra; Becker, Fabian; Grupp, Thomas M; Sievers, Birte; Paulus, Alexander; Gottschalk, Oliver; Jansson, Volkmar

2010-11-01

Poly(ether ether ketone) (PEEK) and its composites are recognized as alternative bearing materials for use in arthroplasty because of their mechanical properties. The objective of this project was to evaluate the biological response of two different kinds of carbon fiber-reinforced (CFR) PEEK compared with ultra-high molecular weight polyethylene (UHMWPE) in vivo as a standard bearing material. Wear particles of the particulate biomaterials were injected into the left knee joint of female BALB/c mice. Assessment of the synovial microcirculation using intravital fluorescence microscopy as well as histological evaluation of the synovial layer were performed 7 days after particle injection. Enhanced leukocyte-endothelial cell interactions and an increase in functional capillary density as well as histological investigations revealed that all tested biomaterials caused significantly (P < 0.05) increased inflammatory reactions compared with control animals (injected with sterile phosphate-buffered saline), without any difference between the tested biomaterials (P > 0.05). These data suggest that wear debris of CFR-PEEK is comparable with UHMWPE in its biological activity. Therefore, CFR-PEEK represents an alternative bearing material because of its superior mechanical and chemical behavior without any increased biological activity of the wear particles, compared with a standard bearing material. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

75 FR 61574 - Unblocking of Specially Designated Nationals and Blocked Persons Pursuant To the Foreign...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-05

... & Implementation, U.S. Department of the Treasury, Office of Foreign Assets Control, Washington, DC 20220, tel... and their organizations on a worldwide basis, with the objective of denying their businesses and... the Central Intelligence Agency, the Director of the Federal Bureau of Investigation, the...

75 FR 65554 - Additional Designations, Foreign Narcotics Kingpin Designation Act

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-25

... Outreach & Implementation, Office of Foreign Assets Control, Department of the Treasury, Washington, DC... objective of denying their businesses and agents access to the U.S. financial system and to the benefits of... with the Attorney General, the Director of the Central Intelligence Agency, the Director of the Federal...

15 CFR 748.9 - Support documents for license applications.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Foreign Aid, U.S. Agency for International Development, for export to a member agency in the foreign... circumstances beyond your control. An exception will not be granted contrary to the objectives of the U.S... (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE EXPORT ADMINISTRATION REGULATIONS...

15 CFR 748.9 - Support documents for license applications.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Foreign Aid, U.S. Agency for International Development, for export to a member agency in the foreign... circumstances beyond your control. An exception will not be granted contrary to the objectives of the U.S... (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE EXPORT ADMINISTRATION REGULATIONS...

15 CFR 748.9 - Support documents for license applications.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Foreign Aid, U.S. Agency for International Development, for export to a member agency in the foreign... circumstances beyond your control. An exception will not be granted contrary to the objectives of the U.S... (Continued) BUREAU OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE EXPORT ADMINISTRATION REGULATIONS...

78 FR 57320 - Food and Drug Administration Food Safety Modernization Act: Proposed Rules on Foreign Supplier...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-18

...: Proposed Rules on Foreign Supplier Verification Programs and the Accreditation of Third-Party Auditors... Accreditation of Third-Party Auditors/Certification Bodies would strengthen the quality, objectivity, and... public can review the proposals on FSVP and the Accreditation of Third-Party Auditors/ Certification...

78 FR 49988 - Food and Drug Administration Food Safety Modernization Act: Proposed Rules on Foreign Supplier...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-16

...: Proposed Rules on Foreign Supplier Verification Programs and the Accreditation of Third-Party Auditors... Accreditation of Third-Party Auditors/Certification Bodies would strengthen the quality, objectivity, and... that the public can review the proposals on FSVP and the Accreditation of Third-Party Auditors...

The Design of Foreign Language Teacher Education.

ERIC Educational Resources Information Center

Banathy, Bela H.

1968-01-01

The developmental scheme of the systems approach could be applied effectively to the design of foreign language teacher education. After the performance objectives had been formulated and the learning tasks analyzed and characterized, the design of the system could be undertaken. This would involve--(1) functions and component analyses, (2) the…

Report on the Audit of Foreign Direct Selling Costs

DTIC Science & Technology

1990-09-18

This is our final report on the Audit of Foreign Direct Selling Costs. The Contract Management Directorate made the audit from October 1989 to...The objective of the audit was to assess whether DoD regulations provided the appropriate incentives to stimulate exports by the. U.S. Defense

Case Closure Procedures for Foreign Military Sales

DTIC Science & Technology

1990-04-05

This is our final report on the Audit of Case Closure Procedures for Foreign Military Sales for your information and use. Comments on a draft of this...report were considered in preparing the final report. We made the audit from January through August 1989. The objectives of the audit were to

Intercultural Competence from Theory to Practice

ERIC Educational Resources Information Center

Campbell, Lynne B.; Comenale, Rebecca

2013-01-01

GLASPORT first convened in October 2009 with funding provided by a Foreign Language Assistance Program (FLAP) grant. The grant proposal was submitted by then Glastonbury Assistant Superintendent of Schools (and former Foreign Language Director) Christine Brown. The committee was charged with two ambitious objectives: (1) to aid in the development…

14 CFR Section 14 - Objective Classification-Nonoperating Income and Expense

Code of Federal Regulations, 2013 CFR

2013-01-01

... under account 82 Other Interest. [ER-1401, 50 FR 245, Jan. 3, 1985] 85Foreign exchange gains and losses. Record here gains and losses from transactions involving currency translations resulting from nonroutine abnormal changes in rates of foreign exchange and gains or losses which arise from translations of long...

14 CFR Section 14 - Objective Classification-Nonoperating Income and Expense

Code of Federal Regulations, 2014 CFR

2014-01-01

... under account 82 Other Interest. [ER-1401, 50 FR 245, Jan. 3, 1985] 85Foreign exchange gains and losses. Record here gains and losses from transactions involving currency translations resulting from nonroutine abnormal changes in rates of foreign exchange and gains or losses which arise from translations of long...

Communicative Differences between Domestic versus Foreign Instructors

ERIC Educational Resources Information Center

Punyanunt-Carter, Narissra; Wrench, Jason S.; Carter, Stacy L.; Linden, Daniel

2014-01-01

The objective of this study was to investigate college students' perceptions of their foreign and domestic classroom instructors. Two hundred and eleven college students participated in the study. The potential participants were approached and offered extra credit to participate, and all needed to have at least one domestic instructor and one…

22 CFR 215.1 - Purpose and scope.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Purpose and scope. 215.1 Section 215.1 Foreign... Purpose and scope. (a) It is the purpose and objective of the International Development Cooperation Agency... procedures by which an individual may obtain notification of the existence of Agency records pertaining to...

22 CFR 215.1 - Purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Purpose and scope. 215.1 Section 215.1 Foreign... Purpose and scope. (a) It is the purpose and objective of the International Development Cooperation Agency... procedures by which an individual may obtain notification of the existence of Agency records pertaining to...

Ingested and Aspirated Foreign Bodies.

PubMed

Green, S Sarah

2015-10-01

Esophageal and aspirated foreign bodies have important clinical significance, and both should be considered carefully when the history or physical examination findings raise sufficient suspicion. The published evidence regarding the diagnosis and management of foreign body ingestion or aspiration is weighted disproportionately with observational studies, case controls, expert opinion, and systematic reviews. Most of the publications would receive a categorization of C (observational studies including case-control and cohort design) and D (expert opinion, case reports, and clinical reasoning). One of the few prospective studies examining the diagnostic evaluation of foreign body aspiration in children could be considered level B evidence (randomized clinical trials, systematic reviews, or diagnostic studies with minor limitations). This study found that the medical history is the most important predictive part of the evaluation. There is evidence for considering bronchoscopy if there is significant history suggestive of foreign body aspiration, even in the setting of normal physical examination findings. (28). Most ingested foreign bodies spontaneously pass without incident. However, special attention should be paid to objects in the esophagus as well as to batteries and magnets. Based on a systematic review of the literature (level B evidence) and the potential for rapid and life-threatening damage, batteries in the esophagus should be removed immediately. (10) Other objects, such as coins, may be observed for passage in an asymptomatic patient. In addition, given the high risk of significant complications, ingestion of high-powered magnets should be quickly and carefully evaluated. Although single magnets are likely to pass without complication, multiple magnets or magnets ingested with other metal objects can cause significant damage and should be removed if there is any concern for mural entrapment, bowel perforation, or failure to progress. (10)(16)(17)(18)(19). Lastly, another systematic review of the literature (level B evidence) about the aspiration of food objects in children suggests that this is a significant public health concern with potentially devastating consequences. Despite clear legislation and regulation by the Consumer Product Safety Commission regarding toys, there is no similar regulation of high-risk foods. The data suggest that there is opportunity for improvement in legislation about the production and packaging of high-risk items as well as in the education of caregivers. (22)

Metallic foreign body in the sphenoid sinus after ballistic injury: a case report.

PubMed

Akhaddar, A; Abouchadi, A; Jidal, M; Gazzaz, M; Elmostarchid, B; Naama, O; Rzin, A; Boucetta, M

2008-05-01

Paranasal sinus injuries by foreign bodies have a lower incidence compared with facial injuries. Among them, penetrating maxillofacial injuries to the sphenoid sinus and skull base remain rare. We report the case of a 41-year-old man who presented with, after a missile-related maxillofacial injury, a metallic foreign body enclosed within the sphenoid sinus with carotid-canal fracture. Angiographic evaluation showed a mass in the right internal carotid artery. The foreign object was successfully extracted through a transmaxillary sublabial approach with a good outcome. We discuss the extensive preoperative evaluation and interdisciplinary management of this unusual injury.

COLLECTING URINE SAMPLES FROM YOUNG CHILDREN USING COTTON GAUZE FOR PESTICIDE STUDIES

EPA Science Inventory

To estimate pesticide exposure, urine samples are often needed to analyze pesticide metabolites. However, this is difficult for children wearing diapers because simple and feasible techniques suitable for field collection are not available. The objectives of this study were to t...

COLLECTING URINE SAMPLES FROM YOUNG CHILDREN USING GAUZE FOR PESTICIDE STUDIES

EPA Science Inventory

To estimate pesticide exposure, urine samples are often needed to analyze pesticide metabolites. However, this is difficult for children wearing diapers because simple and feasible techniques suitable for field collection are not available. The objectives of this study were to te...

A customized vision system for tracking humans wearing reflective safety clothing from industrial vehicles and machinery.

PubMed

Mosberger, Rafael; Andreasson, Henrik; Lilienthal, Achim J

2014-09-26

This article presents a novel approach for vision-based detection and tracking of humans wearing high-visibility clothing with retro-reflective markers. Addressing industrial applications where heavy vehicles operate in the vicinity of humans, we deploy a customized stereo camera setup with active illumination that allows for efficient detection of the reflective patterns created by the worker's safety garments. After segmenting reflective objects from the image background, the interest regions are described with local image feature descriptors and classified in order to discriminate safety garments from other reflective objects in the scene. In a final step, the trajectories of the detected humans are estimated in 3D space relative to the camera. We evaluate our tracking system in two industrial real-world work environments on several challenging video sequences. The experimental results indicate accurate tracking performance and good robustness towards partial occlusions, body pose variation, and a wide range of different illumination conditions.

A Customized Vision System for Tracking Humans Wearing Reflective Safety Clothing from Industrial Vehicles and Machinery

PubMed Central

Mosberger, Rafael; Andreasson, Henrik; Lilienthal, Achim J.

2014-01-01

This article presents a novel approach for vision-based detection and tracking of humans wearing high-visibility clothing with retro-reflective markers. Addressing industrial applications where heavy vehicles operate in the vicinity of humans, we deploy a customized stereo camera setup with active illumination that allows for efficient detection of the reflective patterns created by the worker's safety garments. After segmenting reflective objects from the image background, the interest regions are described with local image feature descriptors and classified in order to discriminate safety garments from other reflective objects in the scene. In a final step, the trajectories of the detected humans are estimated in 3D space relative to the camera. We evaluate our tracking system in two industrial real-world work environments on several challenging video sequences. The experimental results indicate accurate tracking performance and good robustness towards partial occlusions, body pose variation, and a wide range of different illumination conditions. PMID:25264956

Multimodality imaging of foreign bodies of the musculoskeletal system.

PubMed

Jarraya, Mohamed; Hayashi, Daichi; de Villiers, Richard V; Roemer, Frank W; Murakami, Akira M; Cossi, Alda; Guermazi, Ali

2014-07-01

The purpose of this article is to clarify the most relevant points in managing suspected foreign bodies of the musculoskeletal system on the basis of a literature review and published reports with cases to illustrate each type on different imaging modalities. Foreign bodies of the musculoskeletal system are a common problem in emergency departments, with more than a third missed in the initial clinical evaluation. These retained objects may result in various complications and also offer fertile ground for litigation.

Plasma ion implantation technology at Hughes Research Laboratories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matossian, J.N.

1994-03-01

The plasma ion implantation (PII) project at Hughes Research Laboratories (HRL) has as its main objective the evaluation and application of PII technology to improve the tribological properties of metal and nonmetal materials used in aerospace, defense, and commercial applications. The HRL PII facility consists of a 4-ft-diam[times]8-ft-long vacuum chamber capable of implanting objects weighing up to 7000 lbs, and a high-power (100-kW), high-voltage (100-kV) pulse modulator to provide voltage pulses for implantation. Advanced plasma sources have been developed to produce atomic, as well as molecular, nitrogen and oxygen ions, and PII processes have been developed to treat metal andmore » nonmetal materials. The HRL PII facility has been operational since 1989 and has been used for prototype demonstrations of PII technology to achieve (1) a 2--3[times] improved wear life of Co/WC drill bits used for printed-wiring-board fabrication, (2) an 8[times] reduced wear rate for TiN-coated cutting tools, and (3) a 2[times] increased surface hardness for a 7000-lb polymer object, 3 ft by 5 ft by 1 ft.« less

Foreign object - inhaled

MedlinePlus

... can easily inhale small foods (nuts, seeds, or popcorn) and objects (buttons, beads, or parts of toys) ... foods such as hot dogs, whole grapes, nuts, popcorn, food with bones, or hard candy to children ...

The quality of information on the Internet on orthodontic retainer wear: a cross-sectional study.

PubMed

Doğramacı, Esma J; Rossi-Fedele, Giampiero

2016-03-01

The objectives of this study were to assess the accessibility, usability, reliability and quality of information on the Internet written for the lay public about orthodontic retainers, and to elucidate the different retention protocols encouraged. A cross-sectional, observational study. Online, using a computer connected to the Internet in Australia. Two search terms; 'orthodontic retainer' and 'how long should someone wear a retainer after their braces are removed?' were entered alternatively into five search engines. Twenty results for each search term per search engine that fulfilled the inclusion criteria were evaluated in terms of accessibility, usability, reliability and quality of information using the LIDA and DISCERN instruments, ensuring there were no internal or cross-search engine duplicates. Any information about frequency and duration of retainer wear was also collected. Two hundred different websites were identified and assessed. The median overall LIDA score was 72%, corresponding to a moderate quality level. The median total DISCERN score was 47%. Twenty-two websites recommended patients adhere to the specific protocol prescribed to them by their practitioner. There were 45 (22.5%) and 28 (14%) websites advising indefinite use of removable and bonded retainers respectively. Information about retainers on the Internet is easily accessible and usable, though the quality of the content is generally of a moderate level. However, the information is not always accurate and reliable. Both full-time and part-time wear of removable retainers was suggested over greatly varying time periods. Indefinite wear of removable and bonded retainers was also advocated.

In vitro studies on the effect of particle size on macrophage responses to nanodiamond wear debris

PubMed Central

Thomas, Vinoy; Halloran, Brian A.; Ambalavanan, Namasivayam; Catledge, Shane A.; Vohra, Yogesh K.

2012-01-01

Nanostructured diamond coatings improve the smoothness and wear characteristics of the metallic component of total hip replacements and increase the longevity of these implants, but the effect of nanodiamond wear debris on macrophages needs to be determined to estimate the long-term inflammatory effects of wear debris. The objective was to investigate the effect of the size of synthetic nanodiamond particles on macrophage proliferation (BrdU incorporation), apoptosis (Annexin-V flow cytometry), metabolic activity (WST-1 assay) and inflammatory cytokine production (qPCR). RAW 264.7 macrophages were exposed to varying sizes (6, 60, 100, 250 and 500 nm) and concentrations (0, 10, 50, 100 and 200 μg ml−1) of synthetic nanodiamonds. We observed that cell proliferation but not metabolic activity was decreased with nanoparticle sizes of 6–100 nm at lower concentrations (50 μg ml−1), and both cell proliferation and metabolic activity were significantly reduced with nanodiamond concentrations of 200 μg ml−1. Flow cytometry indicated a significant reduction in cell viability due to necrosis irrespective of particle size. Nanodiamond exposure significantly reduced gene expression of tumor necrosis factor-α, interleukin-1β, chemokine Ccl2 and platelet-derived growth factor compared to serum-only controls or titanium oxide (anatase 8 nm) nanoparticles, with variable effects on chemokine Cxcl2 and vascular endothelial growth factor. In general, our study demonstrates a size and concentration dependence of macrophage responses in vitro to nanodiamond particles as possible wear debris from diamond-coated orthopedic joint implants. PMID:22342422

A non-reference evaluation method for edge detection of wear particles in ferrograph images

NASA Astrophysics Data System (ADS)

Wang, Jingqiu; Bi, Ju; Wang, Lianjun; Wang, Xiaolei

2018-02-01

Edges are one of the most important features of wear particles in a ferrograph image and are widely used to extract parameters, recognize types of wear particles, and assist in the identification of the wear mode and severity. Edge detection is a critical step in ferrograph image processing and analysis. Till date, there has been no single algorithm that guarantees the production of good quality edges in ferrograph images for a variety of applications. Therefore, it is desirable to have a reliable evaluation method for measuring the performance of various edge detection algorithms and for aiding in the selection of the optimal parameter and algorithm for ferrographic applications. In this paper, a new non-reference method for the objective evaluation of wear particle edge detection is proposed. In this method, a comprehensive index of edge evaluation is composed of three components, i.e., the reconstruction based similarity sub-index between the original image and the reconstructed image, the confidence degree sub-index used to show the true or false degree of the edge pixels, and the edge form sub-index that is used to determine the direction consistency and width uniformity of the edges. Two experiments are performed to illustrate the validity of the proposed method. First, this method is used to select the best parameters for an edge detection algorithm, and it is then used to compare the results obtained using various edge detection algorithms and determine the best algorithm. Experimental results of various real ferrograph images verify the effectiveness of the proposed method.

Public Health Services for Foreign Workers in Malaysia.

PubMed

Noh, Normah Awang; Wahab, Haris Abd; Bakar Ah, Siti Hajar Abu; Islam, M Rezaul

2016-01-01

The objective of this study was to know the status of the foreign workers' access to public health services in Malaysia based on their utilization pattern. The utilization pattern covered a number of areas, such as frequency of using health services, status of using health services, choice and types of health institutions, and cost of health treatment. The study was conducted on six government hospitals in the Klang Valley area in Kuala Lumpur, Malaysia. Data were collected from 600 foreign patients working in the country, using an interview method with a structured questionnaire. The results showed that the foreign workers' access to public health services was very low. The findings would be an important guideline to formulate an effective health service policy for the foreign workers in Malaysia.

How can the pressure in anti-embolism stockings be maintained during use? Laboratory evaluation of simulated 'wear' and different reconditioning protocols.

PubMed

Macintyre, Lisa; Stewart, Hazel; Rae, Michelle

2016-12-01

Deep vein thrombosis is a major global health issue, responsible for thousands of deaths each year. While thrombi can form under a variety of circumstances, lack of mobility significantly increases risk and therefore non-ambulant patients are frequently fitted with anti-embolism stockings on admission to hospital, to aid blood flow, prevent pooling and thus clotting. Anti-embolism stockings are the most widely used non-invasive medical device on the market and are believed to reduce the risk of deep vein thrombosis by 40%. Despite their widespread use in hospitals world-wide, there is remarkably little research addressing their use or reconditioning and a wide variety of different reconditioning protocols are used in hospitals. The objective of this study was to establish the impact of different wear and reconditioning protocols on the pressure delivering ability of anti-embolism stockings. A laboratory investigation was undertaken to evaluate the pressure delivering ability of 2 major global brands of anti-embolism stockings over 5-8days of simulated wear (extension on static cylinders) and 4 different reconditioning protocols. 1 set of samples was continuously 'worn' for 8days without reconditioning, 1 set of samples was 'worn' for 5days with a day of relaxation between each day of 'wear', 1 set was 'hand washed' and 1 set was machine washed and then allowed to relax between each day of 'wear'. The pressure was measured at the beginning and end of each period of 'wear'. This study was undertaken in a conditioned textile testing laboratory that complies with BS EN ISO 139:2005+A1:2011. The pressure exerted by anti-embolism stockings reduced by between 15 and 24% after 24h of wear, it reduced by between 21 and 32% when worn continuously for 8days. Allowing stockings to rest for a day between days of wear allowed them to recover slightly but this recovery was only temporary. Washing stockings regenerated their pressure delivering potential significantly and machine washing allowed some to recover to exert more pressure than they had when new. Different brands of anti-embolism stockings exert different pressures on the same size of leg, when correctly fitted. The pressure exerted by anti-embolism stockings decreases with use but the correct pressure gradient is maintained if correctly fitted. Washing stockings after 24h of wear is effective in restoring their pressure delivering abilities and in some cases can surpass their 'as new' pressure delivering ability. Copyright © 2016 Elsevier Ltd. All rights reserved.

Increasing trend in retained rectal foreign bodies.

PubMed

Ayantunde, Abraham A; Unluer, Zynep

2016-10-27

To highlight the rising trend in hospital presentation of foreign bodies retained in the rectum over a 5-year period. Retrospective review of the cases of retained rectal foreign bodies between 2008 and 2012 was performed. Patients' clinical data and yearly case presentation with data relating to hospital episodes were collected. Data analysis was by SPSS Inc. Chicago, IL, United States. Twenty-five patients presented over a 5-year period with a mean age of 39 (17-62) years and M: F ratio of 2:1. A progressive rise in cases was noted from 2008 to 2012 with 3, 4, 4, 6, 8 recorded patients per year respectively. The majority of the impacted rectal objects were used for self-/partner-eroticism. The commonest retained foreign bodies were sex vibrators and dildos. Ninty-six percent of the patients required extraction while one passed spontaneously. Two and three patients had retrieval in the Emergency Department and on the ward respectively while 19 patients needed examination under anaesthesia for extraction. The mean hospital stay was 19 (2-38) h. Associated psychosocial issues included depression, deliberate self-harm, illicit drug abuse, anxiety and alcoholism. There were no psychosocial problems identified in 15 patients. There is a progressive rise in hospital presentation of impacted rectal foreign bodies with increasing use of different objects for sexual arousal.

Swimmer's Ear (For Parents)

MedlinePlus

... scratching the ear canal, vigorous ear cleaning with cotton swabs, or putting foreign objects like bobby pins ... Also, never put objects into kids' ears, including cotton-tipped swabs. How Is Swimmer's Ear Treated? Treatment ...

Culture Understanding in Foreign Language Teaching

ERIC Educational Resources Information Center

Qu, Yi

2010-01-01

In the course of foreign language teaching, the priority should always be given to increase international understanding by enabling the students to enter into the life, thought, and literature of people who speak another language. The objective may vary from one period to another, but it should long be present in the thinking of our minds. The…

The World Coal Quality Inventory (WoCQI)

USGS Publications Warehouse

Finkelman, Robert B.; Lovern, Vivian S.

2001-01-01

The Issue Policymakers around the world require accurate information on coal, particularly information on coal properties and characteristics, to make informed decisions regarding the best use of indigenous resources, international import needs and export opportunities, domestic and foreign policy objectives, technology transfer opportunities, foreign investment prospects, environmental and health assessments, and byproduct use and disposal issues.

Summative Evaluation of the Foreign Credential Recognition Program. Final Report

ERIC Educational Resources Information Center

Human Resources and Skills Development Canada, 2010

2010-01-01

A summative evaluation of the Foreign Credential Recognition Program (FCRP) funded by Human Resources and Skills Development Canada (HRSDC) was conducted during the spring, summer and fall of 2008. The main objective of the evaluation was to measure the relevance, impacts, and cost-effectiveness of the program. Given the timing of the evaluation…

Tracking cotton fiber quality and foreign matter through a stripper harvester

USDA-ARS?s Scientific Manuscript database

The main objective of this project was to track cotton fiber quality and foreign matter content throughout the harvesting units and conveying/cleaning systems on a brush-roll stripper harvester. Seed cotton samples were collected at six locations in 2011 and five in 2012 including: 1) hand-picked fr...

[Chalcosis bulbi recognized 22 years after trauma].

PubMed

Yagihashi, Tomoyuki; Wakabayashi, Yoshihiro; Fujita, Satoshi; Fujita, Yasushi; Usui, Masahiko

2006-12-01

To report a case of chalcosis bulbi diagnosed 22 years after accidental entry of a foreign object into the eye. A 57 year-old woman underwent surgery for vitreous opacity and cataract of unknown cause. During the operation, an intraocular foreign body was found in the vitreous at the pars plana, and was removed. The object was a coated copper wire, 3.5 mm in length and 0.2 mm in thickness. She recalled that such a wire had accidentally entered her eye 22 years previously. Copper particles were detected by copper staining of the anterior lens capsule. Fine, sharp metal fragments may penetrate the eye with little resistance. When the injury results in minimal subjective symptoms, the person may not seek examination by an ophthalmologist. In the present case, the foreign body was a fragment of coated copper wire. The exposed metal surface was limited and the copper probably dissolved very slowly. This may account for the lack of significant symptoms. In the Japanese literature, there are many reports of coated copper wire as foreign body in the eye, but few lead to characteristic chalcosis bulbi.

Wearing lower-body compression garment with medium pressure impaired exercise-induced performance decrement during prolonged running

PubMed Central

Mizuno, Sahiro

2017-01-01

Objective To investigate the effect of wearing a lower body compression garment (CG) exerting different pressure levels during prolonged running on exercise-induced muscle damage and the inflammatory response. Methods Eight male participants completed three exercise trials in a random order. The exercise consisted of 120 min of uphill running at 60% of VO2max. The exercise trials included 1) wearing a lower-body CG with 30 mmHg pressure [HIGH]; 2) wearing a lower-body CG with 15 mmHg pressure [MED]; and 3) wearing a lower-body garment with < 5 mmHg pressure [CON]. Heart rate (HR), and rate of perceived exertion for respiration and legs were monitored continuously during exercise. Time-course change in jump height was evaluated before and immediately after exercise. Blood samples were collected to determine blood glucose, lactate, serum creatine kinase, myoglobin, free fatty acids, glycerol, cortisol, and plasma interleukin-6 (IL-6) concentrations before exercise, 60 min of the 120 min exercise period, immediately after exercise, and 60 min after exercise. Results Jump height was significantly higher immediately after the exercise in the MED trial compared with that in the HIGH trial (P = 0.04). Mean HR during the 120 min exercise was significantly lower in the MED trial (162 ± 4 bpm) than that in the CON trial (170 ± 4 bpm, P = 0.01). Plasma IL-6 concentrations increased significantly with exercise in all trials, but the area under the curve during exercise was significantly lower in the MED trial (397 ± 58 pg/ml·120 min) compared with that in the CON trial (670 ± 86 pg/ml·120 min, P = 0.04). Conclusion Wearing a lower body CG exerting medium pressure (approximately 15 mmHg) significantly attenuated decrease in jump performance than that with wearing a lower body CG exerting high pressure (approximately 30 mmHg). Furthermore, exercise-induced increases in HR and the inflammatory response were significantly smaller with CG exerted 15mmHg than that with garment exerted < 5 mmHg. PMID:28562650

Cardiovascular Benefits of Wearing Particulate-Filtering Respirators: A Randomized Crossover Trial

PubMed Central

Shi, Jingjin; Lin, Zhijing; Chen, Renjie; Wang, Cuicui; Yang, Changyuan; Cai, Jing; Lin, Jingyu; Xu, Xiaohui; Ross, Jennifer A.; Zhao, Zhuohui; Kan, Haidong

2016-01-01

Background: Practical approaches to protect individuals from ambient particulate matter (PM) are urgently needed in developing countries. Evidence on the health benefits of wearing particulate-filtering respirators is limited. Objectives: We evaluated the short-term cardiovascular health effects of wearing respirators in China. Methods: A randomized crossover trial was performed in 24 healthy young adults in Shanghai, China in 2014. The subjects were randomized into two groups and wore particulate-filtering respirators for 48 hr alternating with a 3-week washout interval. Heart rate variability (HRV) and ambulatory blood pressure (BP) were continuously monitored during the 2nd 24 hr in each intervention. Circulating biomarkers were measured at the end of each intervention. Linear mixed-effect models were applied to evaluate the effects of wearing respirators on health outcomes. Results: During the intervention periods, the mean daily average concentration of PM with an aerodynamic diameter < 2.5 μm (PM2.5) was 74.2 μg/m3. Compared with the absence of respirators, wearing respirators was associated with a decrease of 2.7 mmHg [95% confidence interval (CI): 0.1, 5.2 mmHg] in systolic BP and increases of HRV parameters, including 12.5% (95% CI: 3.8%, 21.2%) in high frequency (HF) power, 10.9% (95% CI: 1.8%, 20.0%) in the root mean square of the successive differences, and 22.1% (95% CI: 3.6%, 40.7%) in the percentage of normal RR intervals with duration > 50 msec different from the previous normal RR interval (pNN50). The presence of respirators was also associated with a decrease of 7.8% (95% CI: 3.5%, 12.1%) in the ratio of low frequency (LF)/HF power. Conclusions: Short-term wearing of particulate-filtering respirators may produce cardiovascular benefits by improving autonomic nervous function and reducing BP. Citation: Shi J, Lin Z, Chen R, Wang C, Yang C, Cai J, Lin J, Xu X, Ross JA, Zhao Z, Kan H. 2017. Cardiovascular benefits of wearing particulate-filtering respirators: a randomized crossover trial. Environ Health Perspect 125:175–180; http://dx.doi.org/10.1289/EHP73 PMID:27562361

Definition and evaluation of testing scenarios for knee wear simulation under conditions of highly demanding daily activities.

PubMed

Schwiesau, Jens; Schilling, Carolin; Kaddick, Christian; Utzschneider, Sandra; Jansson, Volkmar; Fritz, Bernhard; Blömer, Wilhelm; Grupp, Thomas M

2013-05-01

The objective of our study was the definition of testing scenarios for knee wear simulation under various highly demanding daily activities of patients after total knee arthroplasty. This was mainly based on a review of published data on knee kinematics and kinetics followed by the evaluation of the accuracy and precision of a new experimental setup. We combined tibio-femoral load and kinematic data reported in the literature to develop deep squatting loading profiles for simulator input. A servo-hydraulic knee wear simulator was customised with a capability of a maximum flexion of 120°, a tibio-femoral load of 5000N, an anterior-posterior (AP) shear force of ±1000N and an internal-external (IE) rotational torque of ±50Nm to simulate highly demanding patient activities. During the evaluation of the newly configurated simulator the ability of the test machine to apply the required load and torque profiles and the flexion kinematics in a precise manner was examined by nominal-actual profile comparisons monitored periodically during subsequent knee wear simulation. For the flexion kinematics under displacement control a delayed actuator response of approximately 0.05s was inevitable due to the inertia of masses in movement of the coupled knee wear stations 1-3 during all applied activities. The axial load and IE torque is applied in an effective manner without substantial deviations between nominal and actual load and torque profiles. During the first third of the motion cycle a marked deviation between nominal and actual AP shear load profiles has to be noticed but without any expected measurable effect on the latter wear simulation due to the fact that the load values are well within the peak magnitude of the nominal load amplitude. In conclusion the described testing method will be an important tool to have more realistic knee wear simulations based on load conditions of the knee joint during activities of daily living. Copyright © 2012 IPEM. Published by Elsevier Ltd. All rights reserved.

Compliance among soft contact lens wearers.

PubMed

Kuzman, Tomislav; Kutija, Marija Barisić; Masnec, Sanja; Jandroković, Sonja; Mrazovac, Danijela; Jurisić, Darija; Skegro, Ivan; Kalauz, Miro; Kordić, Rajko

2014-12-01

Contact lens compliance is proven to be crucial for preventing lens wear-related complications because of the interdependence of the steps in lens care regime and their influence on lens system microbial contamination. Awareness of the patients' lens handling compliance as well as correct recognition of non-compliant behaviours is the basis for creating more targeted strategies for patient education. The aim of this study was to investigate compliance among soft contact lens (SCL) wearers in different aspects of lens care handling and wearing habits. In our research 50 asymptomatic lens wearers filled out a questionnaire containing demographic data, lens type, hygiene and wearing habits, lenses and lens care system replacement schedule and self-evaluation of contact lens handling hygiene. We established criteria of compliance according to available manufacturer's recommendations, prior literature and our clinical experience. Only 2 (4%) of patients were fully compliant SCL wearers. The most common non-compliant behaviours were insufficient lens solution soaking time (62%), followed by failure to daily exchange lens case solution and showering while wearing lenses. 44% of patients reported storing lenses in saline solution. Mean lens storage case replacement was 3.6 months, with up to 78% patients replacing lens case at least once in 3 months. Average grade in self evaluating level of compliance was very good (4 +/- 0.78) (from 1-poor level of hygiene to 5-great level of hygiene). Lens wearers who reported excessive daily lens wear and more than 10 years of lens wearing experience were also found to be less compliant with other lens system care procedures. (t = -2.99, df=47, p < 0.0045 and t = -2.33, df= 48, p < 0.024, respectively). Our study indicates that almost all patients had some degree of non-compliance in lens system maintenance steps. Most common non-compliant behaviours were the ones that are crucial for maintaining lens sterility and preventing infection. Despite the low objective compliance rate, self grading was relatively high. Therefore, these results indicate the need for patient education and encouragement of better lens wearing habits and all of the lens maintenance steps at each patient visit.

Review of ear, nose and throat foreign bodies in Sarawak General Hospital. A five year experience.

PubMed

Chiun, Kian Chai; Tang, Ing Ping; Tan, Tee Yong; Jong, Doris Evelyn Yah Hui

2012-02-01

Ear, nose and throat foreign bodies are common in ENT clinical practice. This study was designed to establish the local data of otorhinolaryngeal foreign bodies in term of prevalence among paediatric and adult groups, the clinical features, types of foreign body at different sites, and laterality of foreign bodies. This study was carried out at ENT department, Sarawak General Hospital, Malaysia, from 1st January 2005 to 31st December 2009. A total of 1084 cases were included and statistically analyzed. Ear foreign bodies showed the highest incidence which was consisted of 480 (44.3%) cases, followed by nose in 270 (24.9%) cases, pharynx in 251 (23.2%) cases, esophagus in 57 (5.3%) cases and laryngo-tracheobronchial tree in 26 (2.4%) cases. Otorhinolaryngeal foreign bodies occurred more frequently in 0-10 year old age group which constituted 651 (60.1%) cases. The descending order of frequency for foreign body sites in adult was pharynx (17.2%), ear (12.8%), esophagus (3.1%), nose (1.7%) and laryngo-tracheobronchial tree (1.1%). The type of foreign bodies varies with age group and site of foreign body lodgement. In general, common foreign bodies in both adult and children were food related, with the additional of small objects such as plastic toy in paediatric group. Otorhinolaryngeal foreign bodies were found more frequently in children. The types of foreign body were different from age group and sites of foreign body lodgement. The local food constituted the highest incidence of ear, nose, and throat foreign bodies with additional of plastic toys in paediatric group.

Endoscopic Management of Foreign Bodies in the Upper Gastrointestinal Tract of Adults

PubMed Central

Yao, Chih-Chien; Wu, I-Ting; Lu, Lung-Sheng; Lin, Sheng-Chieh; Liang, Chih-Ming; Kuo, Yuan-Hung; Yang, Shih-Cheng; Wu, Cheng-Kun; Wang, Hsing-Ming; Kuo, Chung-Huang; Chiou, Shue-Shian; Wu, Keng-Liang; Chiu, Yi-Chun; Chuah, Seng-Kee; Tai, Wei-Chen

2015-01-01

Background. Foreign object ingestion and food bolus impaction are a common clinical problem. We report our clinical experiences in endoscopic management for adults, foreign body ingestion, and food bolus impaction. Method. A retrospective chart review study was conducted on adult patients with foreign body ingestion and food bolus impaction between January 2011 and November 2014. Patients with incomplete medical records were excluded. Results. A total of 198 patients (226 incidents) were included in the study (male/female: 1.54/1; age 57 ± 16 years). Among them, 168 foreign bodies were found successfully (74.3%). 75.6% of the foreign bodies were located in the esophagus. Food bolus impaction was most common (41.6%). 93.5% of foreign bodies in current study cohort were successfully extracted and 5 patients required surgical interventions. Comparisons between symptomatic and asymptomatic patients revealed that locations of foreign bodies in the pharynx and esophagus were the significant relevant factors (P < 0.001). Shorter time taken to initiate endoscopic interventions increased detection rate (289.75 ± 465.94 versus 471.06 ± 659.93 minutes, P = 0.028). Conclusion. Endoscopic management is a safe and highly effective procedure in extracting foreign body ingestion and food bolus impaction. Prompt endoscopic interventions can increase the chance of successful foreign bodies' detection. PMID:26258140

Endoscopic Management of Foreign Bodies in the Upper Gastrointestinal Tract of Adults.

PubMed

Yao, Chih-Chien; Wu, I-Ting; Lu, Lung-Sheng; Lin, Sheng-Chieh; Liang, Chih-Ming; Kuo, Yuan-Hung; Yang, Shih-Cheng; Wu, Cheng-Kun; Wang, Hsing-Ming; Kuo, Chung-Huang; Chiou, Shue-Shian; Wu, Keng-Liang; Chiu, Yi-Chun; Chuah, Seng-Kee; Tai, Wei-Chen

2015-01-01

Foreign object ingestion and food bolus impaction are a common clinical problem. We report our clinical experiences in endoscopic management for adults, foreign body ingestion, and food bolus impaction. A retrospective chart review study was conducted on adult patients with foreign body ingestion and food bolus impaction between January 2011 and November 2014. Patients with incomplete medical records were excluded. A total of 198 patients (226 incidents) were included in the study (male/female: 1.54/1; age 57 ± 16 years). Among them, 168 foreign bodies were found successfully (74.3%). 75.6% of the foreign bodies were located in the esophagus. Food bolus impaction was most common (41.6%). 93.5% of foreign bodies in current study cohort were successfully extracted and 5 patients required surgical interventions. Comparisons between symptomatic and asymptomatic patients revealed that locations of foreign bodies in the pharynx and esophagus were the significant relevant factors (P < 0.001). Shorter time taken to initiate endoscopic interventions increased detection rate (289.75 ± 465.94 versus 471.06 ± 659.93 minutes, P = 0.028). Endoscopic management is a safe and highly effective procedure in extracting foreign body ingestion and food bolus impaction. Prompt endoscopic interventions can increase the chance of successful foreign bodies' detection.

Decision making model for Foreign Object Debris/Damage (FOD) elimination in aeronautics using quantitative modeling approach

NASA Astrophysics Data System (ADS)

Lafon, Jose J.

(FOD) Foreign Object Debris/Damage has been a costly issue for the commercial and military aircraft manufacturers at their production lines every day. FOD can put pilots, passengers and other crews' lives into high-risk. FOD refers to any type of foreign object, particle, debris or agent in the manufacturing environment, which could contaminate/damage the product or otherwise undermine quality standards. Nowadays, FOD is currently addressed with prevention programs, elimination techniques, and designation of FOD areas, controlled access to FOD areas, restrictions of personal items entering designated areas, tool accountability, etc. All of the efforts mentioned before, have not shown a significant reduction in FOD occurrence in the manufacturing processes. This research presents a Decision Making Model approach based on a logistic regression predictive model that was previously made by other researchers. With a general idea of the FOD expected, elimination plans can be put in place and start eradicating the problem minimizing the cost and time spend on the prediction, detection and/or removal of FOD.

Modified Balance Error Scoring System (M-BESS) test scores in athletes wearing protective equipment and cleats

PubMed Central

Azad, Aftab Mohammad; Al Juma, Saad; Bhatti, Junaid Ahmad; Delaney, J Scott

2016-01-01

Background Balance testing is an important part of the initial concussion assessment. There is no research on the differences in Modified Balance Error Scoring System (M-BESS) scores when tested in real world as compared to control conditions. Objective To assess the difference in M-BESS scores in athletes wearing their protective equipment and cleats on different surfaces as compared to control conditions. Methods This cross-sectional study examined university North American football and soccer athletes. Three observers independently rated athletes performing the M-BESS test in three different conditions: (1) wearing shorts and T-shirt in bare feet on firm surface (control); (2) wearing athletic equipment with cleats on FieldTurf; and (3) wearing athletic equipment with cleats on firm surface. Mean M-BESS scores were compared between conditions. Results 60 participants were recruited: 39 from football (all males) and 21 from soccer (11 males and 10 females). Average age was 21.1 years (SD=1.8). Mean M-BESS scores were significantly lower (p<0.001) for cleats on FieldTurf (mean=26.3; SD=2.0) and for cleats on firm surface (mean=26.6; SD=2.1) as compared to the control condition (mean=28.4; SD=1.5). Females had lower scores than males for cleats on FieldTurf condition (24.9 (SD=1.9) vs 27.3 (SD=1.6), p=0.005). Players who had taping or bracing on their ankles/feet had lower scores when tested with cleats on firm surface condition (24.6 (SD=1.7) vs 26.9 (SD=2.0), p=0.002). Conclusions Total M-BESS scores for athletes wearing protective equipment and cleats standing on FieldTurf or a firm surface are around two points lower than M-BESS scores performed on the same athletes under control conditions. PMID:27900181

The influence of thermoplastic thoraco lumbo sacral orthoses on standing balance in subjects with idiopathic scoliosis.

PubMed

Khanal, Minoo; Arazpour, Mokhtar; Bahramizadeh, Mahmood; Samadian, Mohammad; Hutchins, Stephen W; Kashani, Reza Vahab; Mardani, Mohammad A; Tari, Hossein Vahid; Aboutorabi, Atefeh; Curran, Sarah; Sadeghi, Heidar

2016-08-01

Idiopathic scoliosis patients have postural equilibrium problems. The objective of this study was to assess postural control in subjects with idiopathic scoliosis following a 4-month intervention in an unbraced position. Quasi-experimental. Eight healthy girls and eight girls with idiopathic scoliosis took part. A Kistler force platform was used with a frequency of 100 Hz for recording data. The center of pressure was recorded in different positions out of brace for scoliosis and healthy subjects. Test conditions were single limb and double limb stance, with eyes open and closed, and foam and rigid surfaces. The data reflected a weak balance of idiopathic scoliosis subjects compared to healthy subjects. After 1 and 4 months of wearing the brace, center of pressure and center of gravity sway increased in the majority of the tests, although there were no significant differences in any of the test conditions (p > 0.05). While the center of pressure sway in medio-lateral direction decreased after 4 months of wearing a brace, in other variables center of pressure and center of gravity sway increased. Idiopathic scoliosis patients have weak balance in comparison to healthy subjects. In addition, following a period of 4 months of wearing a brace, balance parameters in the scoliosis subjects did not improve. The results show that we need more follow-up of orthoses wearing in idiopathic scoliosis subjects and suggest more studies at least 1-year follow-up to identify the efficiency of brace wear on balance. Scoliosis can alter postural stability and balance performance during quiet standing. Spinal deformity can alter a subject's ability to compensate for postural changes and cause gait deviations. This study investigated balance differences between the healthy and idiopathic scoliosis patients and the results of thoraco lumbo sacral orthosis brace wear. It might provide some new insight into the conservative treatment of idiopathic scoliosis patients for clinicians and researchers. © The International Society for Prosthetics and Orthotics 2015.

Self-inflicted foreign bodies in lower genitourinary tract in males: Our experience and review of literature

PubMed Central

Mahadevappa, Nagabhushana; Kochhar, Gaurav; Vilvapathy, Karthikeyan Senguttuvan; Dharwadkar, Sachin; Kumar, Sumit

2016-01-01

Objectives: To study retrospectively the frequency, demographic, phenomenological, and psychiatric profile in patients presented with self-insertion of foreign bodies in the lower genitourinary tract in our institute. Materials and Methods: From January 2009 to 2015, the records of patients admitted with self-insertion of foreign bodies into the lower urinary tract were analyzed retrospectively regarding demographic and phenomenological profile, the mode of presentation, diagnosis, management, complications, and possible contributing factors leading to the event. Results: Out of 17,978 inpatients, ten patients (0.055%) presented with foreign body insertion in the lower genitourinary tract in last 6 years. Mean age was 28.1 ± 13.9 (7–50) years. Objects used for insertion were varied from seeds, twigs to the electric wire. The contributing factors were lack of partner, misconception about masturbation, and underlying psychiatric illness. The presenting symptoms were pain and swelling of the penis, difficulty in voiding, and skin ulceration. The diagnosis was possible by simple observation in four patients, X-ray kidney, ureter, and bladder, and sonography of the pelvis in six patients. Five patients had endoscopic retrieval of foreign body, 2 had an open, suprapubic cystotomy, urethrotomy was needed in one patient, and forceps removal in two patients. There were no postoperative complications. Psychiatric profile was evaluated in nine patients. Conclusions: Foreign body insertion to lower urinary tract was rare. A main cause for insertion of foreign bodies was autoerotism, misconceptions regarding masturbation, and underlying psychiatric illness. In addition to suitable method of surgical removal, counseling and psychiatric evaluation are necessary to prevent recurrences or for early detection of psychiatric problems. PMID:27453657

Analysis of ingested foreign bodies according to age, type and location: a retrospective observational study.

PubMed

Kim, S Y; Park, B; Kong, I G; Choi, H G

2016-12-01

This study aimed to analyse the types and locations of ingested foreign bodies according to different age groups, from infants to the elderly. A retrospective chart review. Tertiary referral centre. A total of 4682 patients who ingested foreign bodies from January 2006 through February 2014. The frequencies of foreign bodies were investigated in each age group. The types of foreign bodies were categorised into fish bones, chicken bones, seafood, tablets, food, metal, batteries, glass, teeth, plastics and others. The anatomic locations of the objects were classified as the oral cavity, tongue base, tonsils, oropharynx, hypopharynx, oesophagus, stomach and colon. The types, locations and origins of the foreign bodies were analysed according to the age groups. The frequency of foreign body ingestion was high in patients up to 14 years of age, after which the risk of foreign body ingestion markedly decreased. Fish bones were the most commonly suspected foreign bodies in all of the age groups. However, non-food-type foreign bodies were more common in both the young and elderly groups. The tonsils were the most common anatomic site of foreign body impaction except in the group of patients older than 65 years. The stomach and oesophagus were also common locations of foreign bodies in the groups of patients younger than 10 years (10.5%) and older than 65 years (39.4%). The frequency of foreign body ingestion was highest in young children. However, we observed specific age-based characteristics that indicate specific precautions to take to avoid foreign body ingestion. © 2015 John Wiley & Sons Ltd.

Managing corneal foreign bodies in office-based general practice.

PubMed

Fraenkel, Alison; Lee, Lawrence R; Lee, Graham A

2017-03-01

Patients with a corneal foreign body may first present to their general practitioner (GP). Safe and efficacious management of these presentations avoids sight-threatening and eye-threatening complications. Removal of a simple, superficial foreign body without a slit lamp is within The Royal Australian College of General Practitioners' (RACGP's) curriculum and scope of practice. Knowing the rele-vant procedural skills and indications for referral is equally important. The objective of this article is to provide an evidence-based and expert-based guide to the management of corneal foreign bodies in the GP's office. History is key to identifying patient characteristics and mechanisms of ocular injury that are red flags for referral. Examination tech-niques and methods of superficial foreign body removal without a slit lamp are outlined, as well as the procedural threshold for referral to an ophthalmologist.

Wearing gloves in the hospital

MedlinePlus

Infection control - wearing gloves; Patient safety - wearing gloves; Personal protective equipment - wearing gloves; PPE - wearing gloves; Nosocomial infection - wearing gloves; Hospital acquired infection - wearing gloves

A Very Long Foreign Body in the Bladder

PubMed Central

Imai, Atsushi; Suzuki, Yuichiro; Hashimoto, Yasuhiro; Sasaki, Atsushi; Saitoh, Hisao; Ohyama, Chikara

2011-01-01

In the urinary tract, foreign body is most commonly found in the urinary bladder. But it is anatomically very difficult for a man to self-insert a long object into the urinary bladder. Here we report a case of a 49-year-old Japanese man who has inserted a 140-cm vinyl tube in the bladder for masturbation. He could not retrieve it, and the bladder foreign body remained in this position for about two years. He was referred to our hospital and open surgery was performed. PMID:21687624

KSC-05PD-0364

NASA Technical Reports Server (NTRS)

2005-01-01

KENNEDY SPACE CENTER, FLA. Preparing for Return to Flight, workers at KSC walk the grounds around Launch Pad 39B looking for Foreign Object Debris, or FOD. The pad was recently refurbished and any possible debris left behind must be removed from the area prior to launch. Foreign objects that are alien to flight systems may cause material damage or may make the system or equipment inoperable, unsafe or less efficient. The Return to Flight mission STS-114 aboard Space Shuttle Discovery will carry supplies and equipment to the International Space Station. Discovery is scheduled for launch in a window from May 15 to June 3.

KSC-05PD-0366

NASA Technical Reports Server (NTRS)

2005-01-01

KENNEDY SPACE CENTER, FLA. Preparing for Return to Flight, workers at KSC walk the grounds around Launch Pad 39B looking for Foreign Object Debris, or FOD. The pad was recently refurbished and any possible debris left behind must be removed from the area prior to launch. Foreign objects that are alien to flight systems may cause material damage or may make the system or equipment inoperable, unsafe or less efficient. The Return to Flight mission STS-114 aboard Space Shuttle Discovery will carry supplies and equipment to the International Space Station. Discovery is scheduled for launch in a window from May 15 to June 3.

KSC-05PD-0363

NASA Technical Reports Server (NTRS)

2005-01-01

KENNEDY SPACE CENTER, FLA. Preparing for Return to Flight, workers at KSC walk the grounds around Launch Pad 39B looking for Foreign Object Debris, or FOD. The pad was recently refurbished and any possible debris left behind must be removed from the area prior to launch. Foreign objects that are alien to flight systems may cause material damage or may make the system or equipment inoperable, unsafe or less efficient. The Return to Flight mission STS-114 aboard Space Shuttle Discovery will carry supplies and equipment to the International Space Station. Discovery is scheduled for launch in a window from May 15 to June 3.

The Portrayal of "Foreigners" in Japanese Social Studies Textbooks: Self-Images of Mono-Ethnic Pluralism

ERIC Educational Resources Information Center

Tsuneyoshi, Ryoko

2007-01-01

History and social studies textbooks have often been the object of heated political debate in various countries, since they relate directly to issues of national identity and citizenship. This article analyzes how "foreigners" are portrayed in two versions (the 2000 and 2006 versions, date of issue) of the best-selling elementary social…

A Language Skills Orientation Program for Foreign Teaching Assistants and Graduate Students.

ERIC Educational Resources Information Center

Brinton, Donna; Gaskill, William

A one-week orientation program designed to increase the effectiveness of foreign teaching assistants (FTA) is described. As the program developed, a decision was made to include non-FTAs with the result that the English language proficiency of the participants covered a wide range and the objectives of the program were mixed. Because of the…

Alternative Approaches for Educating Future Global Marketing Professionals: A Comparison of Foreign Study and Research-Intensive Marketing Programs

ERIC Educational Resources Information Center

Kaufman, Peter A.; Melton, Horace L.; Varner, Iris I.; Hoelscher, Mark; Schmidt, Klaus; Spaulding, Aslihan D.

2011-01-01

Using an experiential learning model as a conceptual background, this article discusses characteristics and learning objectives for well-known foreign study programs such as study tours, study abroad, and internships and compares them with a less common overseas program called the "Global Marketing Program" (GMP). GMP involves…

Vocabulary Teaching in Foreign Language via Audiovisual Method Technique of Listening and Following Writing Scripts

ERIC Educational Resources Information Center

Bozavli, Ebubekir

2017-01-01

The objective is hereby study is to compare the effects of conventional and audiovisual methods on learning efficiency and success of retention with regard to vocabulary teaching in foreign language. Research sample consists of 21 undergraduate and 7 graduate students studying at Department of French Language Teaching, Kazim Karabekir Faculty of…

AN INVESTIGATION OF DIFFERENTIAL BINAURAL STIMULATION IN THE TEACHING OF A FOREIGN LANGUAGE.

ERIC Educational Resources Information Center

VAN RIPER, CHARLES

THIS STUDY DETERMINED WHETHER OR NOT DIFFERENTIAL BINAURAL STIMULATIONS CAN BE USED EFFECTIVELY TO IMPROVE PRONUNCIATION IN FOREIGN LANGUAGE TEACHING. THE OBJECTIVE WAS TO DETERMINE WHAT EFFECT HEARING SIMULTANEOUSLY THE TEACHER'S VOICE IN ONE EAR AND HIS OWN VOICE IN THE OTHER WOULD HAVE ON A STUDENT'S ABILITY TO COMPARE THE DIFFERENCES IN…

Project-Based Method as an Effective Means of Interdisciplinary Interaction While Teaching a Foreign Language

ERIC Educational Resources Information Center

Bondar, Irina Alekseevna; Kulbakova, Renata Ivanovna; Svintorzhitskaja, Irina Andreevna; Pilat, Larisa Pavlovna; Zavrumov, Zaur Aslanovich

2016-01-01

The article explains how to use a project-based method as an effective means of interdisciplinary interaction when teaching a foreign language on the example of The Institute of service, tourism and design (branch) of the North Caucasus Federal University (Pyatigorsk, Stavropol Territory Russia). The article holds the main objectives of the…

Metaphoric Modeling of Foreign Language Teaching and Learning, with Special Reference to Teaching Philosophy Statements

ERIC Educational Resources Information Center

Alghbban, Mohammed I.; Ben Salamh, Sami; Maalej, Zouheir

2017-01-01

The current article investigates teachers' metaphoric modeling of foreign language teaching and learning at the College of Languages and Translation, King Saud University. It makes use of teaching philosophy statements as a corpus. Our objective is to analyze the underlying conceptualizations of teaching/learning, the teachers' perception of the…

Governance and Foreign Aid Allocation

DTIC Science & Technology

2006-07-01

the promotion of market-based principles to restructure macroeconomic policies in developing countries. The greater focus on...the effectiveness of aid in promoting development outcomes. In doing so, I use augmented neoclassical growth framework following Mankiw et al (1992...health care and basic education, macroeconomic reforms and opening markets, the main objective of western foreign aid was to stop newly independent

Public Relations for Foreign Languages. Q & A.

ERIC Educational Resources Information Center

Harnett, Anne Marie

Public relations (PR) is a well-planned campaign of activities the purpose of which is to sell a product (such as foreign language programs) to an external audience. PR differs from publicity in that publicity is a reaction to occasional events whereas PR is a plan with identifiable objectives which extends over a period of time. In conducting a…

Seatbelt usage: is there an association with obesity?

PubMed

Behzad, B; King, D M; Jacobson, S H

2014-09-01

Wearing a seatbelt can prevent motor vehicle crash deaths. While primary seatbelt laws are designed to encourage vehicle passengers to wear seatbelts by allowing law enforcement officers to issue tickets when passengers do not wear seatbelts, discomfort may discourage obese individuals from wearing a seatbelt. The objective of this study is to assess the association between state-level obesity and seatbelt usage rates in the US, and to examine the possible role played by seatbelt laws in these associations. The strength of the association between obesity rates, seatbelt usage, and primary seatbelt laws at the state level is investigated using data from 2006 to 2011. Linear regression analysis is employed. This model estimates that increasing the obesity rate by 1% in a state where a primary seatbelt law (by which law enforcement officers can issue a ticket when seatbelts are not worn) is in effect is associated with a 0.06% decrease in seatbelt usage. However the same percentage of increase in the obesity rate in a state where no primary seatbelt law is in effect is associated with a 0.55% decrease in seatbelt usage. The magnitude of the statistical association between state obesity rates and state-level seatbelt usage is related to the existence of a primary seatbelt law, such that obesity has less impact on seatbelt usage in states where primary seatbelt laws are in effect. Published by Elsevier Ltd.

Hardness and microstructure analysis of damaged gear caused by adhesive wear

NASA Astrophysics Data System (ADS)

Mahendra, Rizky Budi; Nugroho, Sri; Ismail, Rifky

2018-03-01

This study was a result from research on repairing project of damaged elevator gear box. The objective of this research is to analyze the failure part on elevator gearbox at flourmill factory. The equipment was damaged after one year installed and running on factory. Severe wear was occurred on high speed helical gear. These helical gear was one of main part of elevator gearbox in flour mill manufacture. Visually, plastic deformation didn't occurred and not visible on the failure helical gear shaft. Some test would be performed to check the chemical composition, microstructure and hardness of failure helical gear. The material of failure helical gear shaft was a medium carbon steel alloy. The microstructure was showed a martensitic phase formed on the surface to the center area of gear shaft. Otherwise, the depth of hardness layer slight formed on surface and lack depth of hardness layer was a main trigger of severe wear. It was not enough to resist wear due to friction caused by rolling and sliding on surface between high speed gear and low speed gear. Enhancement of hardness layer on surface and depth of hardness layer will make the component has more long life time. Furthermore, to perform next research is needed to analyze the reliability of enhanced hardness on layer and depth of hardness layer on helical gear shaft.

Tribological characterisation of UHMWPE used in dual mobility total hip prosthesis

NASA Astrophysics Data System (ADS)

Essefi, I.; Hakkouna, H.; Ouenzerfi, G.; Mollon, G.; Hamza, S.; Renault, E.; Berthier, Y.; Trunfio-Sfarghiu, A.-M.

2016-08-01

Total hip arthroplasty represents an effective solution for bone and joint diseases. Nevertheless, the hip prosthesis has a limited lifetime, in the average around fifteen years. Their improvement, especially their dual mobility is the objective of this study. Therefore, our strategy is focused on improving the material by comparing three types of polyethylene to determine the best one from a friction mechanism and wear rate minimization standpoint. A dual mobility hip prosthesis, containing a two-sided steel and cobalt chrome cup, was tested with a TORNIER hip joint simulator in calf serum. The rubbed surfaces were characterized using scanning electron microscopy (SEM), contact angle measurements, atomic force microscopy (AFM) and confocal fluorescence microscopy. All these multiscale characterization techniques (from nanoscale to millimeter and micro- scale) showed that the velocity accommodation mechanism is different from one type of polyethylene to another. The wear in the case of standard polyethylene was noticeable and the particles were large and scattered between the surface of polyethylene, the surface of the cup and in the calf serum. For the crosslinked polyethylene, the particles coming from the wear, were not as large, but they were spread the same way as the first case. Even though it shares the same accommodation principle on the detachment of the material with the crosslinked polyethylene the wear particles for the crosslinked vitaminized polyethylene were large and they were only found on the surface of the polyethylene.

Application of Taguchi-grey method to optimize drilling of EMS 45 steel using minimum quantity lubrication (MQL) with multiple performance characteristics

NASA Astrophysics Data System (ADS)

Soepangkat, Bobby O. P.; Suhardjono, Pramujati, Bambang

2017-06-01

Machining under minimum quantity lubrication (MQL) has drawn the attention of researchers as an alternative to the traditionally used wet and dry machining conditions with the purpose to minimize the cooling and lubricating cost, as well as to reduce cutting zone temperature, tool wear, and hole surface roughness. Drilling is one of the important operations to assemble machine components. The objective of this study was to optimize drilling parameters such as cutting feed and cutting speed, drill type and drill point angle on the thrust force, torque, hole surface roughness and tool flank wear in drilling EMS 45 tool steel using MQL. In this study, experiments were carried out as per Taguchi design of experiments while an L18 orthogonal array was used to study the influence of various combinations of drilling parameters and tool geometries on the thrust force, torque, hole surface roughness and tool flank wear. The optimum drilling parameters was determined by using grey relational grade obtained from grey relational analysis for multiple-performance characteristics. The drilling experiments were carried out by using twist drill and CNC machining center. This work is useful for optimum values selection of various drilling parameters and tool geometries that would not only minimize the thrust force and torque, but also reduce hole surface roughness and tool flank wear.

Characterization of cathode keeper wear by surface layer activation

NASA Technical Reports Server (NTRS)

Polk, James E.

2003-01-01

In this study, the erosion rates of the discharge cathode keeper in a 30 cm NSTAR configuration ion thruster were measured using a technique known as Surface Layer Activation (SLA). This diagnostic technique involves producing a radioactive tracer in a given surface by bombardment with high energy ions. The decrease in activity of the tracer material may be monitored as the surface is subjected to wear processes and correlated to a depth calibration curve, yielding the eroded depth. Analysis of the activities was achieved through a gamma spectroscopy system. The primary objectives of this investigation were to reproduce erosion data observed in previous wear studies in order to validate the technique, and to determine the effect of different engine operating parameters on erosion rate. The erosion profile at the TH 15 (23 kw) setting observed during the 8200 hour Life Demonstration Test (LDT) was reproduced. The maximum keeper erosion rate at this setting was determined to be 0.085 pm/hr. Testing at the TH 8 (1.4 kw) setting demonstrated lower erosion rates than TH 15, along with a different wear profile. Varying the keeper voltage was shown to have a significant effect on the erosion, with a positive bias with respect to cathode potential decreasing the erosion rate significantly. Accurate measurements were achieved after operating times of only 40 to 70 hours, a significant improvement over other erosion diagnostic methods.

A Socio-Technical Exploration for Reducing & Mitigating the Risk of Retained Foreign Objects

PubMed Central

Corrigan, Siobhán; Kay, Alison; O’Byrne, Katie; Slattery, Dubhfeasa; Sheehan, Sharon; McDonald, Nick; Smyth, David; Mealy, Ken; Cromie, Sam

2018-01-01

A Retained Foreign Object (RFO) is a fairly infrequent but serious adverse event. An accurate rate of RFOs is difficult to establish due to underreporting but it has been estimated that incidences range between 1/1000 and 1/19,000 procedures. The cost of a RFO incident may be substantial and three-fold: (i) the cost to the patient of physical and/or psychological harm; (ii) the reputational cost to an institution and/or healthcare provider; and (iii) the financial cost to the taxpayer in the event of a legal claim. This Health Research Board-funded project aims to analyse and understand the problem of RFOs in surgical and maternity settings in Ireland and develop hospital-specific foreign object management processes and implementation roadmaps. This project will deploy an integrated evidence-based assessment methodology for social-technical modelling (Supply, Context, Organising, Process & Effects/ SCOPE Analysis Cube) and bow tie methodologies that focuses on managing the risks in effectively implementing and sustaining change. It comprises a multi-phase research approach that involves active and ongoing collaboration with clinical and other healthcare staff through each phase of the research. The specific objective of this paper is to present the methodological approach and outline the potential to produce generalisable results which could be applied to other health-related issues. PMID:29642646

Experimental evaluation of chromium-carbide-based solid lubricant coatings for use to 760 C

NASA Technical Reports Server (NTRS)

Dellacorte, Christopher

1987-01-01

A research program is described which further developed and investigated chromium carbide based self-lubricating coatings for use to 760 C. A bonded chromium carbide was used as the base stock because of the known excellent wear resistance and the chemical stability of chromium carbide. Additives were silver and barium fluoride/calcium fluoride eutectic. The three coating components were blended in powder form, applied to stainless steel substrates by plasma spraying and then diamond ground to the desired coating thickness. A variety of coating compositions was tested to determine the coating composition which gave optimum tribological results. Coatings were tested in air, helium, and hydrogen at temperatures from 25 to 760 C. Several counterface materials were evaluated with the objective of discovering a satisfactory metal/coating sliding combination for potential applications, such as piston ring/cylinder liner couples for Stirling engines. In general, silver and fluoride additions to chromium carbide reduced the friction coefficient and increased the wear resistance relative to the unmodified coating. The lubricant additives acted synergistically in reducing friction and wear.

Tribological Properties of AlSi12-Al₂O₃ Interpenetrating Composite Layers in Comparison with Unreinforced Matrix Alloy.

PubMed

Dolata, Anna Janina

2017-09-06

Alumina-Aluminum composites with interpenetrating network structures are a new class of advanced materials with potentially better properties than composites reinforced by particles or fibers. Local casting reinforcement was proposed to take into account problems with the machinability of this type of materials and the shaping of the finished products. The centrifugal infiltration process fabricated composite castings in the form of locally reinforced shafts. The main objective of the research presented in this work was to compare the tribological properties (friction coefficient, wear resistance) of AlSi12/Al₂O₃ interpenetrating composite layers with unreinforced AlSi12 matrix areas. Profilometric tests enabled both quantitative and qualitative analyses of the wear trace that formed on investigated surfaces. It has been shown that interpenetrating composite layers are characterized by lower and more stable coefficients of friction (μ), as well as higher wear resistance than unreinforced matrix areas. At the present stage, the study confirmed that the tribological properties of the composite layers depend on the spatial structure of the ceramic reinforcement, and primarily the volume and size of alumina foam cells.

Turban pin aspiration: new fashion, new syndrome.

PubMed

Ilan, Ophir; Eliashar, Ron; Hirshoren, Nir; Hamdan, Kasem; Gross, Menachem

2012-04-01

Turban pin aspiration syndrome is a new clinical entity afflicting young Islamic girls wearing a turban.The goal of this study was to present our experience in diagnosis and treatment of this new entity, define its clinical and epidemiologic features, and shed a new light on the role of fashion in the increased incidence. A retrospective study in a tertiary university hospital. Review of clinical parameters and epidemiologic features of 26 patients diagnosed with turban pin aspiration syndrome admitted to the Hadassah-Hebrew University Hospitals in Jerusalem from 1990 to 2010. All patients were Muslim females with an average age of 16 years. In all cases, the history was positive for accidental aspiration. Most of the pins were located in the trachea (42%). In 20 cases, the pins were extracted by rigid bronchoscopy without major complications. Fluoroscopy-assisted rigid bronchoscopy was used successfully in three cases. In one case, the object was self-ejected by coughing before the bronchoscopy, and two patients were referred to the chest unit for thoracotomy. Clinicians should be aware of this distinct form of foreign body aspiration, its method of diagnosis, and extraction techniques. A cultural investigation showed a difference in the turban-fastening technique of young girls as compared with their mothers. Removal by rigid bronchoscopy is a safe method with a high success rate and should be considered as the preferred extraction method of choice. Copyright © 2012 The American Laryngological, Rhinological, and Otological Society, Inc.

Endoscopic Management of Foreign Bodies in the Gastrointestinal Tract: A Review of the Literature

PubMed Central

Andrade, Javier; Twersky, Yitzhak; Iqbal, Shahzad

2016-01-01

Foreign body ingestion is a common diagnosis that presents in emergency departments throughout the world. Distinct foreign bodies predispose to particular locations of impaction in the gastrointestinal tract, commonly meat boluses in the esophagus above a preexisting esophageal stricture or ring in adults and coins in children. Several other groups are at high risk of foreign body impaction, mentally handicapped individuals or those with psychiatric illness, abusers of drugs or alcohol, and the geriatric population. Patients with foreign body ingestion typically present with odynophagia, dysphagia, sensation of having an object stuck, chest pain, and nausea/vomiting. The majority of foreign bodies pass through the digestive system spontaneously without causing any harm, symptoms, or necessitating any further intervention. A well-documented clinical history and thorough physical exam is critical in making the diagnosis, if additional modalities are needed, a CT scan and diagnostic endoscopy are generally the preferred modalities. Various tools can be used to remove foreign bodies, and endoscopic treatment is safe and effective if performed by a skilled endoscopist. PMID:27807447

Thirteen-Year Evaluation of Highly Cross-Linked Polyethylene Articulating With Either 28-mm or 36-mm Femoral Heads Using Radiostereometric Analysis and Computerized Tomography.

PubMed

Nebergall, Audrey K; Greene, Meridith E; Rubash, Harry; Malchau, Henrik; Troelsen, Anders; Rolfson, Ola

2016-09-01

The objective of this 13-year prospective evaluation of highly cross-linked ultra high molecular weight polyethylene (HXLPE) was to (1) assess the long-term wear of HXLPE articulating with 2 femoral head sizes using radiostereometric analysis (RSA) and to (2) determine if osteolysis is a concern with this material through the use of plain radiographs and computerized tomography (CT). All patients received a Longevity HXLPE liner with tantalum beads and either a 28-mm or 36-mm femoral head. Twelve patients (6 in each head size group) agreed to return for 13-year RSA, plain radiograph, and CT follow-up. The 1-year and 13-year plain radiographs as well as the CT scans were analyzed for the presence of osteolysis. The 13-year mean ± standard error steady-state wear was 0.05 ± 0.02 mm with no significant increase over time or between the 2 head size groups. Two patients' CT scans showed radiolucent regions in the acetabulum of 4.51 cm(3) and 11.25 cm(3), respectively. In one patient, this area corresponded to a partially healed degenerative cyst treated with autograft during surgery. The second patient had an acetabular protrusio treated with autograft, and the CT scan revealed areas of remodeling of this graft. One patient's 13-year plain radiographs showed evidence of cup loosening and linear radiolucencies in zones 2 and 3. There was no evidence of significant wear over time using RSA. The CT scans did not show evidence of osteolysis due to wear particles. These results suggest that this material has reduced wear compared to conventional polyethylene, irrespective of head size. Copyright © 2016 Elsevier Inc. All rights reserved.

Wear performance of neat and vitamin E blended highly cross-linked PE under severe conditions: The combined effect of accelerated ageing and third body particles during wear test.

PubMed

Affatato, Saverio; De Mattia, Jonathan Salvatore; Bracco, Pierangiola; Pavoni, Eleonora; Taddei, Paola

2016-12-01

The objective of this study is to evaluate the effects of third-body particles on the in vitro wear behaviour of three different sets of polyethylene acetabular cups after prolonged testing in a hip simulator and accelerated ageing. Vitamin E-blended, cross-linked polyethylene (XLPE_VE), cross-linked polyethylene (XLPE) and conventional polyethylene (STD_PE) acetabular cups were simulator tested for two million cycles under severe conditions (i.e. by adding third-body particles to the bovine calf serum lubricant). Micro-Fourier Transform Infrared and micro-Raman spectroscopic analyses, differential scanning calorimetry, and crosslink density measurements were used to characterize the samples at a molecular level. The STD_PE cups had twice mass loss than the XLPE_VE components and four times than the XLPE samples; statistically significant differences were found between the mass losses of the three sets of cups. The observed wear trend was justified on the basis of the differences in cross-link density among the samples (XLPE>XLPE_VE>STD_PE). FTIR crystallinity profiles, bulk DSC crystallinity and surface micro-Raman crystallinity seemed to have a similar behaviour upon testing: all of them (as well as the all-trans and ortho-trans contents) revealed the most significant changes in XLPE and XLPE_VE samples. The more severe third-body wear testing conditions determined more noticeable changes in all spectroscopic markers with respect to previous tests. Unexpectedly, traces of bulk oxidation were found in both STD_PE (unirradiated) and XLPE (remelting-stabilized), which were expected to be stable to oxidation; on the contrary, XLPE_VE demonstrated a high oxidative stability in the present, highly demanding conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Change in Acetabular Cup Orientation From Supine to Standing Position and Its Effect on Wear of Highly Crosslinked Polyethylene.

PubMed

Teeter, Matthew G; Goyal, Prateek; Yuan, Xunhua; Howard, James L; Lanting, Brent A

2018-01-01

The purpose of this study is to measure acetabular cup position and wear of the highly crosslinked polyethylene liner in the supine and standing position for patients at a minimum of 10 years after the operation. A total of 38 patients were recruited at a mean of 12.5 years after the operation. All patients received a single acetabular cup design with a highly crosslinked liner and a 28-mm cobalt-chromium femoral head. Patients underwent supine and standing radiostereometric examinations in which the X-ray sources and detectors were positioned to obtain an anterior-posterior and cross-table lateral radiograph. Acetabular cup position and the three-dimensional wear rate were measured from the radiographs, and outcome scores were recorded for each patient. Anteversion significantly increased (P < .0001) a mean of 12° from supine (15.1° ± 10.4°) to standing (27.2° ± 10.5°) position. Inclination also significantly increased (P = .001) a mean of 2° from supine (44.4° ± 6.8°) to standing (46.3° ± 7.7°) position. There was no difference (P = .093) in wear rate between supine (0.067 ± 0.070 mm/y) and standing (0.073 ± 0.074 mm/y) positions. There were no correlations between cup orientation and wear rate in either position. Highly crosslinked polyethylene is a forgiving bearing material. Although adherence to the traditional acetabular position target zone is recommended, ensuring hip stability and consideration of the patient's functional position are also important objectives to consider for the acetabular position. Copyright © 2017 Elsevier Inc. All rights reserved.

A mathematical model for foreign body reactions in 2D.

PubMed

Su, Jianzhong; Gonzales, Humberto Perez; Todorov, Michail; Kojouharov, Hristo; Tang, Liping

2011-02-01

The foreign body reactions are commonly referred to the network of immune and inflammatory reactions of human or animals to foreign objects placed in tissues. They are basic biological processes, and are also highly relevant to bioengineering applications in implants, as fibrotic tissue formations surrounding medical implants have been found to substantially reduce the effectiveness of devices. Despite of intensive research on determining the mechanisms governing such complex responses, few mechanistic mathematical models have been developed to study such foreign body reactions. This study focuses on a kinetics-based predictive tool in order to analyze outcomes of multiple interactive complex reactions of various cells/proteins and biochemical processes and to understand transient behavior during the entire period (up to several months). A computational model in two spatial dimensions is constructed to investigate the time dynamics as well as spatial variation of foreign body reaction kinetics. The simulation results have been consistent with experimental data and the model can facilitate quantitative insights for study of foreign body reaction process in general.

Trends in Characteristics and Country of Origin Among Foreign-Trained Nurses in the United States, 1990 and 2000

PubMed Central

Polsky, Daniel; Ross, Sara J.; Brush, Barbara L.; Sochalski, Julie

2007-01-01

Objectives. We describe long-term trends in the characteristics of foreign-trained new entrants to the registered nurse (RN) workforce in the United States. Methods. Using the 1990 and 2000 US Census 5% Public Use Microdata Sample files, we compared trends in characteristics of US- and foreign-trained new entrants to the RN labor force (n=40827) and identified trends in the country of origin of the foreign-trained new entrants. Results. Foreign-trained RNs grew as a percentage of new entrants to the RN workforce, from 8.8% in 1990 to 15.2% in 2000. Compared with US-trained RNs, foreign-trained RNs were 3 times as likely to work in nursing homes and were more likely to have earned a bachelor’s degree. In 2000, 21% of foreign-trained RNs originated from low-income countries, a doubling of the rate since 1990. Conclusions. Foreign-trained RNs now account for a substantial and growing proportion of the US RN workforce. Our findings suggest foreign-trained RNs entering the United States are not of lower quality than US-trained RNs. However, growth in the proportion of RNs from low-income countries may have negative consequences in those countries. PMID:17395844

Wear resistance and mechanisms of composite hardfacings at abrasive impact erosion wear

NASA Astrophysics Data System (ADS)

Surzhenkov, A.; Viljus, M.; Simson, T.; Tarbe, R.; Saarna, M.; Casesnoves, F.

2017-05-01

Tungsten carbide based hardmetal containing sprayed and melted composite hardfacings are prospective for protection against abrasive wear. For selection of abrasive wear resistant hardfacings under intensive impact wear conditions, both mechanical properties (hardness, fracture toughness, etc.) and abrasive wear conditions (type of abrasive, impact velocity, etc.) should be considered. This study focuses on the wear (wear rate and mechanisms) of thick metal-matrix composite hardfacings with hardmetal (WC-Co) reinforcement produced by powder metallurgy technology. The influence of the hardmetal reinforcement type on the wear resistance at different abrasive impact erosion wear (AIEW) conditions was studied. An optimal reinforcement for various wear conditions is described. Based on wear mechanism studies, a mathematical model for wear prediction was drafted.

Increasing trend in retained rectal foreign bodies

PubMed Central

Ayantunde, Abraham A; Unluer, Zynep

2016-01-01

AIM To highlight the rising trend in hospital presentation of foreign bodies retained in the rectum over a 5-year period. METHODS Retrospective review of the cases of retained rectal foreign bodies between 2008 and 2012 was performed. Patients’ clinical data and yearly case presentation with data relating to hospital episodes were collected. Data analysis was by SPSS Inc. Chicago, IL, United States. RESULTS Twenty-five patients presented over a 5-year period with a mean age of 39 (17-62) years and M: F ratio of 2:1. A progressive rise in cases was noted from 2008 to 2012 with 3, 4, 4, 6, 8 recorded patients per year respectively. The majority of the impacted rectal objects were used for self-/partner-eroticism. The commonest retained foreign bodies were sex vibrators and dildos. Ninty-six percent of the patients required extraction while one passed spontaneously. Two and three patients had retrieval in the Emergency Department and on the ward respectively while 19 patients needed examination under anaesthesia for extraction. The mean hospital stay was 19 (2-38) h. Associated psychosocial issues included depression, deliberate self-harm, illicit drug abuse, anxiety and alcoholism. There were no psychosocial problems identified in 15 patients. CONCLUSION There is a progressive rise in hospital presentation of impacted rectal foreign bodies with increasing use of different objects for sexual arousal. PMID:27830039

Release of zirconia nanoparticles at the metal stem-bone cement interface in implant loosening of total hip replacements.

PubMed

Schunck, Antje; Kronz, Andreas; Fischer, Cornelius; Buchhorn, Gottfried Hans

2016-02-01

In a previous failure analysis performed on femoral components of cemented total hip replacements, we determined high volumes of abraded bone cement. Here, we describe the topography of the polished surface of polymethyl methacrylate (PMMA) bone cement containing zirconia radiopacifier, analyzed by scanning electron microscopy and vertical scanning interferometry. Zirconia spikes protruded about 300nm from the PMMA matrix, with pits of former crystal deposition measuring about 400nm in depth. We deduced that the characteristically mulberry-shaped agglomerates of zirconia crystals are ground and truncated into flat surfaces and finally torn out of the PMMA matrix. Additionally, evaluation of in vitro PMMA-on-PMMA articulation confirmed that crystal agglomerations of zirconia were exposed to grain pullout, fatigue, and abrasion. In great quantities, micron-sized PMMA wear and zirconia nanoparticles accumulate in the cement-bone interface and capsular tissues, thereby contributing to osteolysis. Dissemination of nanoparticles to distant lymph nodes and organs of storage has been reported. As sufficient information is lacking, foreign body reactions to accumulated nanosized zirconia in places of long-term storage should be investigated. The production of wear particles of PMMA bone cement in the interface to joint replacement devices, presents a local challenge. The presence of zirconia particles results in frustrated digestion attempts by macrophages, liberation of inflammatory mediators, and necrosis leading to aseptic inflammation and osteolyses. Attempts to minimize wear of articulating joints reduced the attention to the deterioration of cement cuffs. We therefore investigated polished surfaces of retrieved cuffs to demonstrate their morphology and to measure surface roughness. Industrially admixed agglomerates of the radiopacifier are abraded to micron and nano-meter sized particles. The dissemination of zirconia particles in the reticulo-endothelial system to storage organs is a possible burden. Research to replace the actual contrast media by non-particulate material deserves more attention. Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Fault tree analysis of most common rolling bearing tribological failures

NASA Astrophysics Data System (ADS)

Vencl, Aleksandar; Gašić, Vlada; Stojanović, Blaža

2017-02-01

Wear as a tribological process has a major influence on the reliability and life of rolling bearings. Field examinations of bearing failures due to wear indicate possible causes and point to the necessary measurements for wear reduction or elimination. Wear itself is a very complex process initiated by the action of different mechanisms, and can be manifested by different wear types which are often related. However, the dominant type of wear can be approximately determined. The paper presents the classification of most common bearing damages according to the dominant wear type, i.e. abrasive wear, adhesive wear, surface fatigue wear, erosive wear, fretting wear and corrosive wear. The wear types are correlated with the terms used in ISO 15243 standard. Each wear type is illustrated with an appropriate photograph, and for each wear type, appropriate description of causes and manifestations is presented. Possible causes of rolling bearing failure are used for the fault tree analysis (FTA). It was performed to determine the root causes for bearing failures. The constructed fault tree diagram for rolling bearing failure can be useful tool for maintenance engineers.

The Implementation of Industrial Training in Tertiary Education in Malaysia: Objectives, Realisations and Outputs in the Case of Foreign Language Students

ERIC Educational Resources Information Center

Machart, Régis

2017-01-01

The large range of jobs that Malaysian undergraduates of foreign languages are often employed in after completion of their studies (education, tourism, banking, business, management, etc.) is not necessarily related to their major field of study. This situation often makes it difficult for lecturers to develop a comprehensive professional training…

The Illinois State Interdisciplinary Model for Teaching Languages for Business.

ERIC Educational Resources Information Center

Varner, Carson H., Jr.; Whitcomb, Richard O.

This model combines in a team-taught course the study of business and a foreign language. The objective is to give business students a foreign language experience in a relatively brief time and also to offer them a business-oriented introduction to a culture other than their own. Students in business courses are preparing for a career in…

Developing Intercultural Competence of Teachers of English as a Foreign Language through an International Project

ERIC Educational Resources Information Center

Strugielska, Ariadna; Piatkowska, Katarzyna

2016-01-01

This paper reports an international project which took place at Nicolaus Copernicus University, where students and teachers from four European universities met for a two-week summer school. The main objective was to develop intercultural competence of teachers of English as a foreign language and their ability to demonstrate this skill during an…

Pre-School Foreign Language Teaching and Learning--A Network Innovation Project in Slovenia

ERIC Educational Resources Information Center

Brumen, Mihaela; Berro, Fanika Fras; Cagran, Branka

2017-01-01

The paper describes some findings about teaching foreign languages (FL) in a pre-school setting obtained from the Network Innovation Project (NIP). The aims of the NIP were to research and practise the most effective teaching approaches and organizational models in teaching and learning of FL in pre-schools. The objectives were to determine how…

Maintaining Foreign Language Skills for the Advanced-Course Dropout. ERIC Focus Reports on the Teaching of Foreign Languages, Number 1.

ERIC Educational Resources Information Center

Grittner, Frank M.

The nationwide need for maintenance of skills programs for students who discontinue their language studies 1-3 years before college is explained. Figures based on a national questionnaire identify the extent of this need, and possible program objectives and structure are suggested. Major attention is directed to such student activities as…

Uncovering the Fundamental Nature of Tribological Interfaces: High Resolution Tribology and Spectroscopy of Ultrahard Nanostructured Diamond Films for MEMS and Beyond

DTIC Science & Technology

2007-12-31

Wisconsin-Madison) for 2? ol !> o "S \\ % M 31 Statement of Objectives The original objectives of the proposal were as follows: 1. Obtain high-quality...performed multiple PEEM experiments on wear tracks on carbon-based films and polysilicon micro-electro mechanical systems (MEMS) devices, a comprehensive... polysilicon MEMS device known as the "nanotractor", and studies of the structure and composition of UNCD, ta-C, and nanocrystalline diamond (NCD) films. They

Asymmetric MF-DCCA method based on risk conduction and its application in the Chinese and foreign stock markets

NASA Astrophysics Data System (ADS)

Cao, Guangxi; Han, Yan; Li, Qingchen; Xu, Wei

2017-02-01

The acceleration of economic globalization gradually shows the linkage of the stock markets in various counties and produces a risk conduction effect. An asymmetric MF-DCCA method is conducted based on the different directions of risk conduction (DMF-ADCCA) and by using the traditional MF-DCCA. To ensure that the empirical results are more objective and robust, this study selects the stock index data of China, the US, Germany, India, and Brazil from January 2011 to September 2014 using the asymmetric MF-DCCA method based on different risk conduction effects and nonlinear Granger causality tests to study the asymmetric cross-correlation between domestic and foreign stock markets. Empirical results indicate the existence of a bidirectional conduction effect between domestic and foreign stock markets, and the greater influence degree from foreign countries to domestic market compared with that from the domestic market to foreign countries.

Investigation into the need for ingesting foreign imaging exams into local systems and evaluation of the design challenges of Foreign Exam Management (FEM)

NASA Astrophysics Data System (ADS)

Milovanovic, Lazar; Agrawal, Arun; Bak, Peter; Bender, Duane; Koff, David

2015-03-01

The deployment of regional and national Electronic Health Record solutions has been a focus of many countries throughout the past decade. Most of these deployments have taken the approach of "sharing" imaging exams via portals and web-based viewers. The motivation of portal/web-based access is driven by a) the perception that review of imaging exams via portal methods is satisfactory to all users and b) the perceived complexity of ingesting foreign exams into local systems. This research project set out to objectively evaluate who really needs foreign exams within their local systems, what those systems might be and how often this is required. Working on the belief that Foreign Exam Management (FEM) is required to support clinical workflow, the project implemented a FEM capability within an XDSI. b domain to identify the design challenges and nuances associated with FEM.

So You "Gotta" Wear Glasses Minicourse, Career Oriented Pre-Technical Physics.

ERIC Educational Resources Information Center

Dallas Independent School District, TX.

This instructional guide, intended for student use, develops the topic of optics through a series of sequential activities. A technical development of the subject is pursued with examples stressing practical aspects of the concepts. Included in the minicourse are: (1) the rationale, (2) terminal behavioral objectives, (3) enabling behavioral…

30 CFR 56.15002 - Hard hats.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Hard hats. 56.15002 Section 56.15002 Mineral... HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personal Protection § 56.15002 Hard hats. All persons shall wear suitable hard hats when in or around a mine or plant where falling objects...

30 CFR 56.15002 - Hard hats.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Hard hats. 56.15002 Section 56.15002 Mineral... HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personal Protection § 56.15002 Hard hats. All persons shall wear suitable hard hats when in or around a mine or plant where falling objects...

30 CFR 56.15002 - Hard hats.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Hard hats. 56.15002 Section 56.15002 Mineral... HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personal Protection § 56.15002 Hard hats. All persons shall wear suitable hard hats when in or around a mine or plant where falling objects...

30 CFR 56.15002 - Hard hats.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Hard hats. 56.15002 Section 56.15002 Mineral... HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personal Protection § 56.15002 Hard hats. All persons shall wear suitable hard hats when in or around a mine or plant where falling objects...

30 CFR 56.15002 - Hard hats.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Hard hats. 56.15002 Section 56.15002 Mineral... HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Personal Protection § 56.15002 Hard hats. All persons shall wear suitable hard hats when in or around a mine or plant where falling objects...

Annual Report - Compatibility of ZDDP and ionic liquid anti-wear additives with hard coatings for engine lubrications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qu, Jun; Zhou, Yan; Leonard, Donovan N

The objectives for this considerations described here are to; investigate the compatibility of engine lubricant antiwear (AW) additives, specifically conventional zinc dialkyldithiophosphate (ZDDP) and newly developed ionic liquids (ILs), with selected commercial hard coatings, and provide fundamental understanding to guide future development of engine lubricants.

Experimental assessment of eye protection efficiency against high speed projectiles.

PubMed

Speck, Alexis; Zelzer, Benedikt; Eppig, Timo; Langenbucher, Achim

2013-02-01

Work in hazardous zones with the risk of mechanical injuries requires protection with safety spectacles. Mechanical eye injuries with metal foreign bodies are often caused by rotational material machining or production processes with high pressure or high velocity moving parts. Normative regulations restrict to tests with small and fast flying objects (e.g. 6mm ball). The literature does not provide any information about protection capabilities against larger objects with high mass and arbitrary shape. The purpose of this study was to test the protection efficiency of safety spectacles against flying objects. The scope of this paper is to present a new test setup for mechanical impact resistance testing of personal protective eyewear against objects with arbitrary shape and mass. The setup is based on a catapult platform, accelerating a sliding carriage on a rail. A pull rope system allows velocities up to 62±2 m·s(-1). A photo sensor was used for velocity measurement. The carriage can be loaded with projectiles of up to 30mm×30mm×40mm in size with arbitrary orientation, depending on the carriage insert. Testing and validation was done with projectiles such as 7g metal chips and fragments with approximate dimensions of 10mm×15mm. Samples were standard occupational safety spectacles mounted on a test head. The projectile impact was captured with a monochrome high speed camera. The aiming accuracy test showed deviations of approximately 1mm of two impacts on the same spectacle surface with a free flight distance of 150mm. All tests with slow, medium and high speed projectiles showed no contact with the eye medium. Objects with velocities from 10 m·s(-1) to 62 m·s(-1) fired the spectacle off from the test head. The medium speed test cut off one side of the spectacle frame. The high speed test with 62±2 m·s(-1) cracked the polycarbonate shield. We describe a method for accelerating arbitrary objects up to 62 m·s(-1) and for aiming these objects on safety eyewear, mounted on a test head. The setup allows a variety of projectile shapes, orientations and velocities. The accuracy of velocity measurement is ± 2 m·s(-1) for high velocity (< ± 5%). Further studies will address optimization of this setup due to signs of wear and gliding properties of the carriage, wireless ignition and higher velocities. Copyright © 2012. Published by Elsevier GmbH.

Cranial injury caused by penetrating non-missile foreign body: an autopsy case.

PubMed

Eren, B; Türkmen, N; Toprak Ergönen, A; Gündogmus, U N

2012-10-01

Presented case was 32-year-old male marble worker, who underwent industrial accident at workplace. On gross physical examination; on forehead region round skin wound in 0.9 cm diameter was detected, radiological examination showed the image of metallic object. in the skull cavity. Brain dissection showed obvious brain injury, haemorrahge explaining the pattern of injury caused by the metallic bodys path, from left frontal lobe to the left cerebellar hemisphere was identified. We presented rare case of penetrating injury of the cranial region caused by non-missile foreign body. cranial injury - non-missile foreign body - autopsy.

Wear Mechanism Maps for Magnesium Alloy AM60 and Composite AM60-9% (Al2O3)f

NASA Astrophysics Data System (ADS)

Ullah Khan, Muhammad Zafar

The purpose of this work was to study the tribological behaviour of squeeze cast Mg alloy AM60 and its composite AM60-9% (Al2O3) f. Dry sliding wear tests were performed on specimens of these materials using a block-on-ring tribometer which was equipped with a COF and temperature measurement system. Wear, COF and temperature maps were constructed to illustrate the effect of temperature and COF on the wear behaviour of the Mg alloy and it's composite. Four wear regimes namely low, mild, transient and severe wear were identified. The transition from mild to severe wear regime was found to be dependent on the bulk temperature of the specimen. Oxidational wear prevailed in low and mild wear whereas plastic deformation induced wear and melt wear controlled the wear rates in transient and severe wear regimes, respectively. This study shows that the incorporation of Al2O3 fibres in AM60 alloy improved the wear resistance of the resulting composite by delaying the transition from mild to severe wear.

Wear behaviors of pure aluminum and extruded aluminum alloy (AA2024-T4) under variable vertical loads and linear speeds

NASA Astrophysics Data System (ADS)

Jung, Jeki; Oak, Jeong-Jung; Kim, Yong-Hwan; Cho, Yi Je; Park, Yong Ho

2017-11-01

The aim of this study was to investigate the transition of wear behavior for pure aluminum and extruded aluminum alloy 2024-T4 (AA2024-T4). The wear test was carried using a ball-on-disc wear testing machine at various vertical loads and linear speeds. The transition of wear behaviors was analyzed based on the microstructure, wear tracks, wear cross-section, and wear debris. The critical wear rates for each material are occurred at lower linear speed for each vertical load. The transition of wear behavior was observed in which abrasion wears with the generation of an oxide layer, fracture of oxide layer, adhesion wear, severe adhesion wear, and the generation of seizure occurred in sequence. In case of the pure aluminum, the change of wear debris occurred in the order of blocky, flake, and needle-like debris. Cutting chip, flake-like, and coarse flake-like debris was occurred in sequence for the extruded AA2024-T4. The transition in the wear behavior of extruded AA2024-T4 occurred slower than in pure aluminum.

Wear Characteristics and Mechanisms of H13 Steel with Various Tempered Structures

NASA Astrophysics Data System (ADS)

Cui, X. H.; Wang, S. Q.; Wei, M. X.; Yang, Z. R.

2011-08-01

Wear tests of H13 steel with various tempering microstructures were performed under atmospheric conditions at room temperature (RT), 200 °C, and 400 °C. The wear characteristics and wear mechanisms of various tempered microstructures of the steel were focused by investigating the structure, morphology, and composition of the worn surfaces. Under atmospheric conditions at RT, 200 °C, and 400 °C, adhesive wear, mild oxidation wear, and oxidation wear prevailed, respectively. The wear rate at 200 °C was substantially lower than those at RT and 400 °C due to the protection of tribo-oxides. In mild oxidation wear, the tempered microstructures of the steel presented almost no obvious influence on the wear resistance. However, in adhesive wear and oxidation wear, the wear resistance strongly depended on the tempered microstructures of the steel. The steel tempered at 600-650 °C presented pronouncedly lower wear rates than the one tempered at 200-550 or 700 °C. It can be suggested that the wear resistance of the steel was closely related with its fracture resistance.

Diagnosis and Treatment of Hardware Disease.

PubMed

Miesner, Matt D; Reppert, Emily J

2017-11-01

Eating habits in cattle are less discriminant than other ruminants, and they more often accidentally ingest strange objects while feeding. Penetrating foreign bodies may cause mild to severe peritonitis, penetrate the diaphragm to cause pleuritis or pericarditis, or cause localized abscesses in the thorax or abdomen. Because these objects are most often metal, a common term for this problem is hardware disease. An accurate history and thorough physical examination often yields a diagnosis; however, ancillary diagnostics can enhance accuracy and disease magnitude before exploratory surgery. Treatment encompasses controlling infection and inflammation and foreign body removal; preventive measures are emphasized. Copyright © 2017 Elsevier Inc. All rights reserved.

KSC-05PD-0365

NASA Technical Reports Server (NTRS)

2005-01-01

KENNEDY SPACE CENTER, FLA. Preparing for Return to Flight, workers at KSC walk the grounds around Launch Pad 39B looking for and picking up Foreign Object Debris, or FOD. The pad was recently refurbished and any possible debris left behind must be removed from the area prior to launch. Foreign objects that are alien to flight systems may cause material damage or may make the system or equipment inoperable, unsafe or less efficient. The Return to Flight mission STS-114 aboard Space Shuttle Discovery will carry supplies and equipment to the International Space Station. Discovery is scheduled for launch in a window from May 15 to June 3.

Region Based CNN for Foreign Object Debris Detection on Airfield Pavement

PubMed Central

Cao, Xiaoguang; Wang, Peng; Meng, Cai; Gong, Guoping; Liu, Miaoming; Qi, Jun

2018-01-01

In this paper, a novel algorithm based on convolutional neural network (CNN) is proposed to detect foreign object debris (FOD) based on optical imaging sensors. It contains two modules, the improved region proposal network (RPN) and spatial transformer network (STN) based CNN classifier. In the improved RPN, some extra select rules are designed and deployed to generate high quality candidates with fewer numbers. Moreover, the efficiency of CNN detector is significantly improved by introducing STN layer. Compared to faster R-CNN and single shot multiBox detector (SSD), the proposed algorithm achieves better result for FOD detection on airfield pavement in the experiment. PMID:29494524

Region Based CNN for Foreign Object Debris Detection on Airfield Pavement.

PubMed

Cao, Xiaoguang; Wang, Peng; Meng, Cai; Bai, Xiangzhi; Gong, Guoping; Liu, Miaoming; Qi, Jun

2018-03-01

In this paper, a novel algorithm based on convolutional neural network (CNN) is proposed to detect foreign object debris (FOD) based on optical imaging sensors. It contains two modules, the improved region proposal network (RPN) and spatial transformer network (STN) based CNN classifier. In the improved RPN, some extra select rules are designed and deployed to generate high quality candidates with fewer numbers. Moreover, the efficiency of CNN detector is significantly improved by introducing STN layer. Compared to faster R-CNN and single shot multiBox detector (SSD), the proposed algorithm achieves better result for FOD detection on airfield pavement in the experiment.

[Influence of multiple sintering on wear behavior of Cercon veneering ceramic].

PubMed

Gao, Qing-ping; Chao, Yong-lie; Jian, Xin-chun; Guo, Feng

2010-04-01

To investigate the influence of multiple sintering on wear behavior of Cercon veneering ceramic. Samples were fabricated according to the manufacture's requirement for different sintering times (1, 3, 5, 7 times). The wear test was operated with a modified MM-200 friction and wear machine in vitro. The wear scars were characterized by scanning electron microscope (SEM) and atomic force microscopy (AFM). With the sintering times increasing, the wear scar width became larger. The correlation was significant at the 0.01 level. Significant difference was observed in wear scar width among different samples (P < 0.05). SEM and AFM results showed that veneering ceramic wear facets demonstrated grooves characteristic of abrasive wear. Multiple sintering can decrease the wear ability of Cercon veneer, and the wear pattern has the tendency to severe wear.

Feasibility of objectively measured physical activity and sedentary behavior in patients with malignant pleural effusion.

PubMed

Jeffery, Emily; Lee, Yc Gary; McVeigh, Joanne; Straker, Leon; Wooding, Troy; Newton, Robert U; Peddle-McIntyre, Carolyn

2017-10-01

Malignant pleural effusion (MPE) affects 1 million people worldwide annually and can significantly impair physical activity. Accelerometry is a validated method of objectively assessing physical activity. The purpose of this study was to determine the compliance in patients with MPE to accelerometry and describe their activity. Patients with MPE wore an Actigraph GT3X accelerometer over a 7-day continuous wear protocol. Compliance was measured as the percent of patients who had ≥4 valid days (i.e., 8-h/day of waking wear-time). Eastern Cooperative Oncology Group performance status was documented the day of actigraphy initialization. Forty-six patients with MPE received accelerometers; 44 (95.7%) returned their device. No complications were reported on their use. Forty subjects (90.9%) had ≥4 valid days of wear-time. Patients spent most of their waking hours sedentary [mean 11.0 h (SD 1.95)], with limited participation in moderate and vigorous physical activity [mean 9.5 min (SD 14.16)]. Compared to patients with better performance status (n = 32), patients with poorer performance status (n = 11) spent significantly more hours/day sedentary [mean difference 2.1 (CI 0.86-3.32); p = 0.001], as did those who survived <3 months (n = 5) compared to >12 months (n = 27) [mean difference 2.6 (CI 0.49-4.77); p = 0.013). Accelerometry was applied successfully in patients with MPE with high compliance and no adverse events. This is the first reported objectively measured physical activity in patients with MPE and revealed high sedentary behavior and low physical activity. The data reflected patient performance status and discriminated between survival groups. Accelerometry can provide a useful measure for future interventional studies in patients with MPE.

Effects of Prism Eyeglasses on Objective and Subjective Fixation Disparity

PubMed Central

Schroth, Volkhard; Joos, Roland; Jaschinski, Wolfgang

2015-01-01

In optometry of binocular vision, the question may arise whether prisms should be included in eyeglasses to compensate an oculomotor and/or sensory imbalance between the two eyes. The corresponding measures of objective and subjective fixation disparity may be reduced by the prisms, or the adaptability of the binocular vergence system may diminish effects of the prisms over time. This study investigates effects of wearing prisms constantly for about 5 weeks in daily life. Two groups of 12 participants received eyeglasses with prisms having either a base-in direction or a base-out direction with an amount up to 8 prism diopters. Prisms were prescribed based on clinical fixation disparity test plates at 6 m. Two dependent variables were used: (1) subjective fixation disparity was indicated by a perceived offset of dichoptic nonius lines that were superimposed on the fusion stimuli and (2) objective fixation disparity was measured with a video based eye tracker relative to monocular calibration. Stimuli were presented at 6 m and included either central or more peripheral fusion stimuli. Repeated measurements were made without the prisms and with the prisms after about 5 weeks of wearing these prisms. Objective and subjective fixation disparity were correlated, but the type of fusion stimulus and the direction of the required prism may play a role. The prisms did not reduce the fixation disparity to zero, but induced significant changes in fixation disparity with large effect sizes. Participants receiving base-out prisms showed hypothesized effects, which were concurrent in both types of fixation disparity. In participants receiving base-in prisms, the individual effects of subjective and objective effects were negatively correlated: the larger the subjective (sensory) effect, the smaller the objective (motor) effect. This response pattern was related to the vergence adaptability, i.e. the individual fusional vergence reserves. PMID:26431525

Short term endurance results on a single cylinder diesel engine fueled with upgraded bio oil biodiesel emulsion

NASA Astrophysics Data System (ADS)

Prakash, R.; Murugan, S.

2017-11-01

This paper deliberates the endurance test outcomes obtained from a single cylinder, diesel engine fueled with an upgraded bio oil biodiesel emulsion. In this investigation a bio oil obtained by pyrolysis of woody biomass was upgraded with acid treatment. The resulted bio oil was emulsified with addition of biodiesel and suitable surfactant which is termed as ATJOE15. The main objective of the endurance test was to evaluate the wear characteristics of the engine components and lubrication oil properties, when the engine is fueled with the ATJOE15 emulsion. The photographic views taken before and after the end of 100 hrs endurance test, and visual inspection of the engine components, wear and carbon deposit results, are discussed in this paper.

Inspection of wear particles in oils by using a fuzzy classifier

NASA Astrophysics Data System (ADS)

Hamalainen, Jari J.; Enwald, Petri

1994-11-01

The reliability of stand-alone machines and larger production units can be improved by automated condition monitoring. Analysis of wear particles in lubricating or hydraulic oils helps diagnosing the wear states of machine parts. This paper presents a computer vision system for automated classification of wear particles. Digitized images from experiments with a bearing test bench, a hydraulic system with an industrial company, and oil samples from different industrial sources were used for algorithm development and testing. The wear particles were divided into four classes indicating different wear mechanisms: cutting wear, fatigue wear, adhesive wear, and abrasive wear. The results showed that the fuzzy K-nearest neighbor classifier utilized gave the same distribution of wear particles as the classification by a human expert.

The Use of EPOSTL to Determine the Self-Efficacy of Prospective EFL Teachers: Raising Awareness in English Language Teacher Education

ERIC Educational Resources Information Center

Bergil, Ayfer Su; Sariçoban, Arif

2017-01-01

The current practices in the field of foreign language teacher education have a heavy inclination to make use of traditional means especially throughout the assessment process of student teachers at foreign language departments. Observing the world in terms of teacher education makes it urgent to include more reflective and objective tools in…

Setting Learning Objectives in Translation at the Department of Foreign Language Teaching through the Concept of Competence

ERIC Educational Resources Information Center

Eser, Oktay

2014-01-01

At the department of foreign language teaching, a variety of courses are offered in order for students to acquire translation competence. The courses are often carried out by translating a text from one language into the other. Learning by experience is an effective approach. However, it is inevitable that there are some aspects that we need to…

To Explore Managerial Issues and Their Implications on e-Government Deployment in the Public Sector: Lessons from Taiwan's Bureau of Foreign Trade

ERIC Educational Resources Information Center

Tseng, Paul T. Y.; Yen, David C.; Hung, Yu-Chung; Wang, Nana C. F.

2008-01-01

The objective of this article is to explore the experience of reconciling the strategic information system (IS) management with the radical transition of the Information Technology (IT) infrastructure in Taiwan's Bureau of Foreign Trade (BOFT) between 1998 and 2003. This investigation will be beneficial for the implementation of IT projects, as…

Nasal foreign bodies in children: should they have a plain radiograph in the accident and emergency?

PubMed

Glynn, Fergal; Amin, Mohamed; Kinsella, John

2008-04-01

To determine the proportion of children with nasal foreign bodies who had button batteries as the foreign body. To describe the clinical care and outcome of those children with a button battery foreign body. A retrospective review of all children presenting to the accident and emergency room with a nasal foreign body or unilateral nasal discharge during a 6-month period was assessed. Forty-four children were included. The most common object found was a plastic bead (27%), followed by foam, paper, or tissue fragments (23%); food matter represented 15%. A button battery was found in 3 patients (7%); other foreign bodies included stones, buttons, crayons, erasers, and a pellet. Thiry-six (82%) had their foreign body removed without anesthetic and 8 (18%) required a general anesthetic. All 3 children with a button battery went undiagnosed until examination in the operating theater. Because there was no previous indication of the presence of a button battery in the 3 children, the removal of the foreign body under general anesthesia was scheduled for the following day. The removal of the button batteries would have been expedited had a plain radiograph been obtained, possibly resulting in less morbidity for our patients. We recommend a plain radiograph in all children presenting with a nonvisible foreign body or unilateral nasal discharge.

Comfort, Ocular Dryness, and Equilibrium Water Content Changes of Daily Disposable Contact Lenses.

PubMed

Insua Pereira, Eduardo; Lira, Madalena

2017-10-26

The objective of this investigation was to evaluate the level of comfort and ocular dryness during wear with six daily disposable contact lenses (DDCL) and also determine the changes in contact lens equilibrium water content (EWC) resulting from their wear. In this contralateral open trial, 27 subjects were randomly fitted with six DDCL (stenfilcon A, delefilcon A, nelfilcon A, narafilcon A, nesofilcon A, and omafilcon A). The evaluation of comfort and ocular dryness sensation was recorded by the participants at two moments of the day (11 AM and 5 PM) over a period of 10 days of contact lens wear. The assessment was made with the aid of visual analogue scales (0-10). The refractive index of 54 contact lenses was accessed by a single operator using a digital automated refractometer (CLR 12-70; Index Instruments). The EWC of the lenses was estimated based on its refractive index values. Comfort ratings were slightly higher for delefilcon A (9.56±0.67, P=0.01) and narafilcon A (9.40±0.93, P=0.01) and these lenses wearers also reported less ocular dryness. The results revealed a pronounced water content reduction for omafilcon A (P=0.002), narafilcon A (P=0.008), and nesofilcon A (P=0.003). Although changes in subjective responses and EWC were distinct among the materials analyzed, all the contact lenses performed well during the 10 days of wear.

Effect of natural gel product on bovine dentin erosion in vitro

PubMed Central

SALES-PERES, André de Carvalho; MARSICANO, Juliane Avansini; GARCIA, Rudan Paraíso; FORIM, Moacir Rossi; da SILVA, Maria Fatima das Graças Fernandes; SALES-PERES, Sílvia Helena de Carvalho

2013-01-01

Objective To evaluate the efficacy of Neem (Azadirachta indica) experimental gel for the prevention of erosive wear on bovine dentin, in vitro. Material and Methods One hundred dentin blocks were allocated into 5 experimental groups (20 samples each): C (control group, without gel); CG (control group, only base gel); F (fluoride gel, 1.23% NaF; pH 4.1, Dentsply; Brazil); N (Neem gel, 10% neem extract; pH 4.1, manipulation); NF (Neem+fluoride gel, 10% Neem extract and 1.23% NaF; pH 4.1, manipulation). The blocks were stored in artificial saliva for 24 hours. After this, they were submitted to six alternating re- and demineralization cycles. The blocks were analyzed for wear (profilometry). The results were submitted to statistical analysis by ANOVA and Tukey tests (P<0.05). Results The mean wear (±SD, µm) was shown as follows in groups: C (13.09±0.99), CG (10.60±1.99), F (10.90±1.44), N (12.68±1.13) and NF (10.84±1.65). All gels showed some preventive action when compared with control group. However, significant differences were found only between Neem+fluoride gel and fluoride gel. Conclusion A single application of a neem-containing fluoride gel reduced dentin erosion, thus it is a possible alternative in reducing dental wear. Further research should investigate the action mechanism and the synergism between them. PMID:24473728

Thermal Treatment, Sliding Wear and Saline Corrosion of Al In Situ Reinforced with Mg2Si and Ex Situ Reinforced with TiC Particles

NASA Astrophysics Data System (ADS)

Lekatou, A. G.; Poulia, A.; Mavros, H.; Karantzalis, A. E.

2018-02-01

The main objective of this work is to produce a composite consisting of (a) a cast heat-treatable Al-Mg-Si alloy with high contents of Mg for corrosion resistance and Si to offset the Mg-due poor castability (in situ hypoeutectic Mg2Si/Al composite) and (b) TiC particles at high enough volume fractions (≤ 15%), in order to achieve a satisfactory combination of wear and corrosion performance. TiCp/Al-7Mg-5Si (wt.%) composites were produced by flux-assisted casting followed by solution and aging heat treatment. Solution treatment led to a relatively uniform dispersion and shape rounding of Mg2Si precipitates and Si particles. TiC particle addition resulted in refinement of primary Al, modification of the Mg2Si Chinese script morphology and refinement/spheroidization of primary Mg2Si. Heat treatment combined with TiC addition notably improved the sliding wear resistance of Al-7Mg-5Si. A wear mechanism has been proposed. The TiC/Al interfaces remained intact of corrosion during potentiodynamic polarization of the heat-treated materials in 3.5 wt.% NaCl. Different main forms of localized corrosion in 3.5 wt.% NaCl were identified for each TiC content (0, 5, 15 vol.%), depending on specific degradation favoring microstructural features (topology/size/interface wetting) at each composition.

[Wear behavior of enamel and veneering ceramics].

PubMed

Gao, Qing-ping; Chao, Yong-lie; Jian, Xin-chun; Guo, Feng; Meng, Yu-kun

2007-10-01

To compare the wear between the enamel and two types of dental decoration porcelains for all-ceramic restorations (Vita-alpha, Vintage AL). Friction coefficients, wear scar width, element concentrations and wear surface evolution were considered relatively to the tribology of that in vivo situation. The wear scars of the samples were characterized by means of dynamic atomic force microscopy (DFM). The different element concentrations of the surface before/after the wear test were determined with energy dispersion spectrometry (EDS). The friction coefficient varied from time in each kind of material. The statistical differences between materials were observed in wear scar width and properties of materials (P<0.05). DFM results showed wear surface of natural tooth full of abrasive particles and denaturation of dental texture. Wear surface of veneering ceramics consisted mainly of abrasive particles, plough and microcracking. EDS results showed that the element concentration of Fe was obviously found on the samples after wear. The main underlying mechanisms of natural teeth wear are abrasive, and denaturation of dental texture. Abrasive wear, adhesion and fatigue of veneering ceramics characterize the wear patterns which plays different role in Vita-alpha and Vintage AL. The wear patterns of veneering ceramics can be described as mild wear.

Nanoclay-Reinforced Glass-Ionomer Cements: In Vitro Wear Evaluation and Comparison by Two Wear-Test Methods

PubMed Central

Fareed, Muhammad A.; Stamboulis, Artemis

2017-01-01

Glass ionomer cement (GIC) represents a major transformation in restorative dentistry. Wear of dental restoratives is a common phenomenon and the determination of the wear resistance of direct-restorative materials is a challenging task. The aim of this paper was to evaluate the wear resistance of novel glass ionomer cement by two wear-test methods and to compare the two wear methods.The wear resistance of a conventional glass ionomer cement (HiFi Advanced Health Care Kent, UK) and cements modified by including various percentages of nanoclays (1, 2 and 4 wt %) was measured by a reciprocating wear test (ball-on-flat) and Oregon Health and Sciences University’s (OHSU) wear simulator. The OHSU wear simulation subjected the cement specimens to three wear mechanisms, namely abrasion, three-body abrasion and attrition using a steatite antagonist. The abrasion wear resulted in material loss from GIC specimen as the steatite antagonist forced through the exposed glass particles when it travelled along the sliding path.The hardness of specimens was measured by the Vickers hardness test. The results of reciprocation wear test showed that HiFi-1 resulted in the lowest wear volume 4.90 (0.60) mm3 (p < 0.05), but there was no significant difference (p > 0.05) in the wear volume in comparison to HiFi, HiFi-2 and HiFi-4. Similarly, the results of OHSU wear simulator showed that the total wear volume of HiFi-4 1.49 (0.24) was higher than HiFi-1 and HiFi-2. However, no significant difference (p > 0.05) was found in the OHSU total wear volume in GICs after nanoclay incorporation. The Vickers hardness (HV) of the nanoclay-reinforced cements was measured between 62 and 89 HV. Nanoclay addition at a higher concentration (4%) resulted in higher wear volume and wear depth. The total wear volumes were less dependent upon abrasion volume and attrition volume. The total wear depths were strongly influenced by attrition depth and to some extent by abrasion depth. The addition of nanoclay in higher wt % to HiFi did not result in significant improvement in wear resistance and hardness. Nonetheless, wear is a very complex phenomenon because it is sensitive to a wide number of factors that do not necessarily act in the same way when compared using different parameters. PMID:29563434

[Foreign body ingestion in children: our experience and review of the literature].

PubMed

Orofino, Antonio; Lanzillotto, Maria Paola; D'Amato, Michele; Rutigliano, Vincenzo; Fanelli, Benito

2009-01-01

Foreign body ingestion is a frequent event in paediatric population, especially in the first six years of life. Even if the event is normally cause of anxiety for the parents witness of the situation, fortunately most ingested foreign bodies ingestion, about 80-90%, pass spontaneously, 10-20% of cases needs an endoscopic intervention and only in less than 1% of cases surgery is necessary. Many authors suggest different guide-lines for diagnosis and therapy of foreign body ingestion in children. These purposes are discordant not only on potential danger of foreign body, but also on timing and last of waiting period before endoscopic extraction. Here we report our own experience: a retrospective review of three hundred consecutive paediatric cases of foreign body ingestion between June 2001 and February 2008. This study don't take in account patients with pathology either organic either functional, that can cause stop of food progression. We describe and discuss about medical diagnostic and therapeutic procedures that have been done during the time of hospitalization and performed according to classic and new international literature, with the objective to propose recommendations helpful for a correct management of children presenting with a history of suspected ingestion of a foreign body.

[New technique for safe removal of impacted foreign bodies in the upper gastrointestinal tract using reusable variceal "cap" (cup, cap or cylinder)].

PubMed

Chávez Rossell, Miguel

2012-01-01

The ingestion of a foreign body is one of the most common endoscopic emergencies. Foreign bodies in the upper gastrointestinal tract should be extracted as soon as possible to avoid serious complications such as perforation o bleeding. However, removals of foreign bodies with sharp edges are very difficult and can develop complications during their removal. Various devices have therefore been developed to prevent mucosal injury from the sharp edges during endoscopic extraction. We report a new technique for the successful foreign body extraction of upper digestive tract using the cap from six shooter variceal banding reused. We present 17 cases (9 males and 8 females). The types of foreign bodies removed were: chicken bones (n:7), fish bones (n:3), denture prosthesis (n:2), food bolus (n:2), long pin (n:1), golden thumb tack (n: 1) and press-through package (n:1). There were no complications. This new technique is safe and effective. Highlights its advantages: enhanced sight pharyngo esophageal junction, foreign bodies disimpact at that level, food bolus suck, avoid sharp object damage mucosal or scope and decrease time removal.

Endoscopic techniques and management of foreign body ingestion and food bolus impaction in the upper gastrointestinal tract: a retrospective analysis of 139 cases.

PubMed

Katsinelos, Panagiotis; Kountouras, Jannis; Paroutoglou, George; Zavos, Christos; Mimidis, Kostas; Chatzimavroudis, Grigoris

2006-10-01

Ingested foreign bodies and food bolus impaction are frequently seen in endoscopic practice. Successful foreign body and food bolus removal may depend on the method used, the choice of device, and the experience level of the endoscopist, although few papers report experience and outcome of tertiary centers. To investigate the effectiveness of our protocol designed for removal of ingested foreign bodies and food boluses. We retrospectively reviewed all patients with a diagnosis of foreign body ingestion and food bolus impaction from 1994 to 2005 identified by computer search. Patients were excluded if medical record was incomplete. The analysis included 171 patients. Foreign bodies and impacted food boluses were found in 77 and 62 patients, respectively. In 32 cases (23%), the foreign bodies passed spontaneously through the gastrointestinal tract. The overall success rate for endoscopic management was obtained in 137 patients (98.6%). Surgical removal of a foreign body was required in only 2 cases (1.4%). According to the type and location of the foreign object and food bolus we used Dormia baskets, retrieval forceps, polypectomy snares, and all sizes of Roth net. No complications relating to the endoscopic procedure were observed; 50 patients (35.2%) had an underlying esophageal disease. Endoscopic removal of upper gastrointestinal tract foreign bodies and food bolus impaction is efficacious and safe. Especially the Roth net is the best device for safe retrieval of food boluses and button disc batteries.

Attitudes of states' economic and industrial development advisors toward foreign investments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dashti, A.Y.

The general purpose of this dissertation is to investigate the effects of inward foreign investments' characteristics on the nature and intensity of the attitudes of host nationals in an advanced country. Specifically, interest was focused on the following aspects of inward foreign investments in the US: (a) national origin of investments (countries included are Saudi Arabia and Kuwait, England, West Germany, Holland, and Japan); (b) types of foreign-investment operation (types of investment included are farming, manufacturing, petroleum, real estate, and retailing); (c) foreign investors' forms of entry into the US; and (d) extent of foreign ownership. The study also investigatedmore » any variations in the attitudes prevalent among the host nationals toward the four aspects of foreign investments, based on demographic variables: age, religion, ethnic background, personal contact with particular foreigners, overseas travel experience in general and to specific countries, place of birth based on geographic and level of income regions, geographic mobility, place of work based on geographic and level of income regions, occupation, education, and political philosophy. The objective here also includes, as a corollary, an examination of the existence of stereotype, prejudice, and ethnocentric tendencies. A number of implications were also revealed by the study and discussed in the dissertation. These were related to theory of host national attitudes towad foreign investments, present and potential foreign investors in the US, and US public-policy makers and politicians (both at the local and federal levels).« less

The research of computer multimedia assistant in college English listening

NASA Astrophysics Data System (ADS)

Zhang, Qian

2012-04-01

With the technology development of network information, there exists more and more seriously questions to our education. Computer multimedia application breaks the traditional foreign language teaching and brings new challenges and opportunities for the education. Through the multiple media application, the teaching process is full of animation, image, voice, and characters. This can improve the learning initiative and objective with great development of learning efficiency. During the traditional foreign language teaching, people use characters learning. However, through this method, the theory performance is good but the practical application is low. During the long time computer multimedia application in the foreign language teaching, many teachers still have prejudice. Therefore, the method is not obtaining the effect. After all the above, the research has significant meaning for improving the teaching quality of foreign language.

Effect of bionic coupling units' forms on wear resistance of gray cast iron under dry linear reciprocating sliding condition

NASA Astrophysics Data System (ADS)

Pang, Zuobo; Zhou, Hong; Xie, Guofeng; Cong, Dalong; Meng, Chao; Ren, Luquan

2015-07-01

In order to get close to the wear form of guide rails, the homemade linear reciprocating wear testing machine was used for the wear test. In order to improve the wear-resistance of gray cast iron guide rail, bionic coupling units of different forms were manufactured by a laser. Wear behavior of gray-cast-iron with bionic-coupling units has been studied under dry sliding condition at room temperature using the wear testing machine. The wear resistance was evaluated by means of weight loss measurement and wear morphology. The results indicated that bionic coupling unit could improve the wear resistance of gray cast iron. The wear resistance of gray cast iron with reticulation bionic coupling unit is the best. When the load and speed changed, reticulation bionic coupling unit still has excellent performance in improving the wear resistance of gray cast iron.

Evaluation of composite wear with a new multi-mode oral wear simulator.

PubMed

Condon, J R; Ferracane, J L

1996-07-01

The goals of this study were to develop a machine which simultaneously produces wear through the two main oral wear mechanisms of abrasion and attrition by the action of an enamel antagonist and to compare the results obtained for dental composites using this machine to those obtained from clinical studies and other in vitro studies. The accuracy of this new wear tester was determined by examining 11 commercial composite filling materials and 1 amalgam. Specimens were subjected to three-body abrasion and attrition wear for 50,000 cycles. Profilometry was used to quantitate wear of the composites. Linear regression analysis was used to correlate the results to those obtained from clinical studies, as well as from other in vitro wear testers. The area of enamel wear was also determined by image analysis. The SEM was used to evaluate the wear surfaces. The lowest abrasion wear was recorded for the amalgam and for the microfill and smaller-particle composites. Attrition wear was enhanced for the microfill composites and one small-particle hybrid. There was a strong correlation between the results obtained with the new wear tester and those obtained in the clinical trials cited in the literature. Wear of the enamel antagonist was the greatest for the composites with the largest particle sizes. The wear tester showed a reasonable correlation with other wear-producing machines. A new wear tester developed to evaluate and discriminate abrasion and attrition wear provided results similar to those reported in the literature for a variety of commercial composites. The new machine is capable of characterizing the behavior of a material in multiple wear modes simultaneously with one simple, realistic test.

Penetrating ballistic-like frontal brain injury caused by a metallic rod.

PubMed

Pascual, J M; Navas, M; Carrasco, R

2009-06-01

Penetrating non-missile intracranial injuries caused by metallic foreign bodies are very rare among the civilian population. We present a unique instance of a severe, high-energy, penetrating orbitocranial injury caused by a solid metallic rod that corresponded to the spray valve lever handle of a kitchen sink pre-rinse spray tap, which was fractured and projected at high speed for an unknown reason. To our knowledge, this is the first report of a high-energy, penetrating brain injury caused by such an object. After careful radiological evaluation of the shape and position of the foreign object, a combined right frontal craniotomy and supraorbital osteotomy was performed in order to achieve safe removal of the metal bar. Successful surgical treatment of an orbitocranial injury caused by a similar object has not previously been reported.

Investigation of tribological properties of biobased polymers and polymeric composites

NASA Astrophysics Data System (ADS)

Bhuyan, Satyam Kumar

Worldwide potential demands for replacing petroleum derived raw materials with renewable plant-based ones in the production of valuable polymeric materials and composites are quite significant from the social and environmental standpoints. Therefore, using low-cost renewable resources has deeply drawn the attention of many researchers. Among them, natural oils are expected to be ideal alternative feedstock since oils, derived from plant and animal sources, are found in profusion in the world. The important feature of these types of materials is that they can be designed and tailored to meet different requirements. The real challenge lies in finding applications which would use sufficiently large quantities of these materials allowing biodegradable polymers to compete economically in the market. Lack of material and tribological characterizations have created an awareness to fulfill this essential objective. In order to understand the viability of biobased polymers in structural applications, this thesis work elucidates the study of friction and wear characteristics of polymers and polymeric composites made out of natural oil available profusely in plants and animals. The natural oils used in this study were soybean and tung oil. Various monomeric components like styrene, divinely benzene etc. were used in the synthesis of biobased polymers through Rh-catalyzed isomerization techniques. For the different polymeric composites, spent germ, a byproduct of ethanol production, is used as the filler and an organoclay called montmorillonite is used as the reinforcing agent in the polymer matrix. The effect of crosslinker concentration, filler composition and reinforcement agent concentration was studied under dry sliding. A ball-on-flat tribometer with a probe made out of steel, silicon nitride or diamond was used for most of the experimental work to measure friction and generate wear. The wear tracks were quantified with an atomic force microscope and a contact profilometer. The wear morphologies were studied with a scanning electron microscope. Thermosetting epoxy resin was used as a benchmark material to compare the tribological characteristics of the biobased polymers. Synthetic polymeric materials made out of norbornene monomers were also subjected to friction and wear tests. An empirical relationship between wear behavior and crosslinking was established.

Numerical and experimental investigations for the evaluation of the wear coefficient of reverse total shoulder prostheses.

PubMed

Mattei, Lorenza; Di Puccio, Francesca; Joyce, Thomas J; Ciulli, Enrico

2015-03-01

In the present study, numerical and experimental wear investigations on reverse total shoulder arthroplasties (RTSAs) were combined in order to estimate specific wear coefficients, currently not available in the literature. A wear model previously developed by the authors for metal-on-plastic hip implants was adapted to RTSAs and applied in a double direction: firstly, to evaluate specific wear coefficients for RTSAs from experimental results and secondly, to predict wear distribution. In both cases, the Archard wear law (AR) and the wear law of UHMWPE (PE) were considered, assuming four different k functions. The results indicated that both the wear laws predict higher wear coefficients for RTSA with respect to hip implants, particularly the AR law, with k values higher than twofold the hip ones. Such differences can significantly affect predictive wear model results for RTSA, when non-specific wear coefficients are used. Moreover, the wear maps simulated with the two laws are markedly different, although providing the same wear volume. A higher wear depth (+51%) is obtained with the AR law, located at the dome of the cup, while with the PE law the most worn region is close to the edge. Taking advantage of the linear trend of experimental volume losses, the wear coefficients obtained with the AR law should be valid despite having neglected the geometry update in the model. Copyright © 2015 Elsevier Ltd. All rights reserved.

A mechanistic understanding of the wear coefficient: From single to multiple asperities contact

NASA Astrophysics Data System (ADS)

Frérot, Lucas; Aghababaei, Ramin; Molinari, Jean-François

2018-05-01

Sliding contact between solids leads to material detaching from their surfaces in the form of debris particles, a process known as wear. According to the well-known Archard wear model, the wear volume (i.e. the volume of detached particles) is proportional to the load and the sliding distance, while being inversely proportional to the hardness. The influence of other parameters are empirically merged into a factor, referred to as wear coefficient, which does not stem from any theoretical development, thus limiting the predictive capacity of the model. Based on a recent understanding of a critical length-scale controlling wear particle formation, we present two novel derivations of the wear coefficient: one based on Archard's interpretation of the wear coefficient as the probability of wear particle detachment and one that follows naturally from the up-scaling of asperity-level physics into a generic multi-asperity wear model. As a result, the variation of wear rate and wear coefficient are discussed in terms of the properties of the interface, surface roughness parameters and applied load for various rough contact situations. Both new wear interpretations are evaluated analytically and numerically, and recover some key features of wear observed in experiments. This work shines new light on the understanding of wear, potentially opening a pathway for calculating the wear coefficient from first principles.

Physical Activity Intervention Using Fitbits in an Introductory College Health Course

ERIC Educational Resources Information Center

Rote, Aubrianne E

2017-01-01

Objective: This study took the form of an intervention examining change in physical activity and quality of experience among students in an introductory health course who were asked to wear a Fitbit activity monitor throughout the semester. Method: College students (N = 56) took part in this controlled trial. Students enrolled in an introductory…

Handheld Metal Detector for Metallic Foreign Body Ingestion in Pediatric Emergency.

PubMed

Hamzah, Hazwani Binte; James, Vigil; Manickam, Suraj; Ganapathy, Sashikumar

2018-01-04

Foreign body ingestion is a common problem for which children present to the emergency department. The most common ingested foreign bodies among children are coins. Metal detector is an equipment, which measures a change in inductance of a coil when an electroconductive material is placed near it and produces an audio-visual signal. The present study was conducted to determine the effectiveness and feasibility of HMD in the local Pediatric population. This was a prospective study conducted in the pediatric emergency department among children presenting with history of foreign body ingestion. The outcome measured was presence or absence of metallic foreign body detected on handheld metal detector examination. During the study period, 36 patients with history of foreign body ingestion presented to the emergency department. Among these, 28 were metallic foreign body ingestions. Coins were the most common type of foreign body ingested. Among the metallic foreign bodies ingested, all the coins were accurately identified by the handheld metal detector. Non-coin metallic foreign bodies like metallic screw, needle and stapler pin were not identified by the handheld metal detector. The study demonstrates that handheld metal detector can be safely and reliably used as a screening tool in the process of detecting ingested coins. The plain radiograph still appears to be superior as it accurately localizes sharp metallic objects as well as cell batteries (button batteries) which need to be detected early and removed in order to prevent complications. Handheld metal detector is an effective tool that can be used in the follow up of patients to confirm whether the coin like metallic foreign body has been expelled. Handheld metal detector examination is more sensitive than traditional X-ray examination to detect radiolucent metallic foreign bodies like aluminium.

75 FR 7536 - Culturally Significant Objects Imported for Exhibition Determinations: “The Aztec Pantheon and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-19

... objects at the Getty Villa, Pacific Palisades, CA, from on or about March 24, 2010, until on or about July.... 2459), Executive Order 12047 of March 27, 1978, the Foreign Affairs Reform and Restructuring Act of...

Mechanism-Based FE Simulation of Tool Wear in Diamond Drilling of SiCp/Al Composites.

PubMed

Xiang, Junfeng; Pang, Siqin; Xie, Lijing; Gao, Feinong; Hu, Xin; Yi, Jie; Hu, Fang

2018-02-07

The aim of this work is to analyze the micro mechanisms underlying the wear of macroscale tools during diamond machining of SiC p /Al6063 composites and to develop the mechanism-based diamond wear model in relation to the dominant wear behaviors. During drilling, high volume fraction SiC p /Al6063 composites containing Cu, the dominant wear mechanisms of diamond tool involve thermodynamically activated physicochemical wear due to diamond-graphite transformation catalyzed by Cu in air atmosphere and mechanically driven abrasive wear due to high-frequency scrape of hard SiC reinforcement on tool surface. An analytical diamond wear model, coupling Usui abrasive wear model and Arrhenius extended graphitization wear model was proposed and implemented through a user-defined subroutine for tool wear estimates. Tool wear estimate in diamond drilling of SiC p /Al6063 composites was achieved by incorporating the combined abrasive-chemical tool wear subroutine into the coupled thermomechanical FE model of 3D drilling. The developed drilling FE model for reproducing diamond tool wear was validated for feasibility and reliability by comparing numerically simulated tool wear morphology and experimentally observed results after drilling a hole using brazed polycrystalline diamond (PCD) and chemical vapor deposition (CVD) diamond coated tools. A fairly good agreement of experimental and simulated results in cutting forces, chip and tool wear morphologies demonstrates that the developed 3D drilling FE model, combined with a subroutine for diamond tool wear estimate can provide a more accurate analysis not only in cutting forces and chip shape but also in tool wear behavior during drilling SiC p /Al6063 composites. Once validated and calibrated, the developed diamond tool wear model in conjunction with other machining FE models can be easily extended to the investigation of tool wear evolution with various diamond tool geometries and other machining processes in cutting different workpiece materials.

Mechanism-Based FE Simulation of Tool Wear in Diamond Drilling of SiCp/Al Composites

PubMed Central

Xiang, Junfeng; Pang, Siqin; Xie, Lijing; Gao, Feinong; Hu, Xin; Yi, Jie; Hu, Fang

2018-01-01

The aim of this work is to analyze the micro mechanisms underlying the wear of macroscale tools during diamond machining of SiCp/Al6063 composites and to develop the mechanism-based diamond wear model in relation to the dominant wear behaviors. During drilling, high volume fraction SiCp/Al6063 composites containing Cu, the dominant wear mechanisms of diamond tool involve thermodynamically activated physicochemical wear due to diamond-graphite transformation catalyzed by Cu in air atmosphere and mechanically driven abrasive wear due to high-frequency scrape of hard SiC reinforcement on tool surface. An analytical diamond wear model, coupling Usui abrasive wear model and Arrhenius extended graphitization wear model was proposed and implemented through a user-defined subroutine for tool wear estimates. Tool wear estimate in diamond drilling of SiCp/Al6063 composites was achieved by incorporating the combined abrasive-chemical tool wear subroutine into the coupled thermomechanical FE model of 3D drilling. The developed drilling FE model for reproducing diamond tool wear was validated for feasibility and reliability by comparing numerically simulated tool wear morphology and experimentally observed results after drilling a hole using brazed polycrystalline diamond (PCD) and chemical vapor deposition (CVD) diamond coated tools. A fairly good agreement of experimental and simulated results in cutting forces, chip and tool wear morphologies demonstrates that the developed 3D drilling FE model, combined with a subroutine for diamond tool wear estimate can provide a more accurate analysis not only in cutting forces and chip shape but also in tool wear behavior during drilling SiCp/Al6063 composites. Once validated and calibrated, the developed diamond tool wear model in conjunction with other machining FE models can be easily extended to the investigation of tool wear evolution with various diamond tool geometries and other machining processes in cutting different workpiece materials. PMID:29414839

Experimental study on internal cooling system in hard turning of HCWCI using CBN tools

NASA Astrophysics Data System (ADS)

Ravi, A. M.; Murigendrappa, S. M.

2018-04-01

In recent times, hard turning became most emerging technique in manufacturing processes, especially to cut high hard materials like high chrome white cast iron (HCWCI). Use of Cubic boron nitride (CBN), pCBN and Carbide tools are most appropriate to shear the metals but are uneconomical. Since hard turning carried out in dry condition, lowering the tool wear by minimizing tool temperature is the only solution. Study reveals, no effective cooling systems are available so for in order to enhance the tool life of the cutting tools and to improve machinability characteristics. The detrimental effect of cutting parameters on cutting temperature is generally controlled by proper selections. The objective of this paper is to develop a new cooling system to control tool tip temperature, thereby minimizing the cutting forces and the tool wear rates. The materials chosen for this work was HCWCI and cutting tools are CBN inserts. Intricate cavities were made on the periphery of the tool holder for easy flow of cold water. Taguchi techniques were adopted to carry out the experimentations. The experimental results confirm considerable reduction in the cutting forces and tool wear rates.

Investigating the Evolution of Progressive Die Wear on Uncoated Dp1180 Steel in Production Environment

NASA Astrophysics Data System (ADS)

Wu, W.; Zhou, D. J.; Adamski, D. J.; Young, D.; Wang, Y. W.

2017-09-01

A study of die wear was performed using an uncoated dual phase, 1,180 MPa ultimate tensile strength steel (DP1180) in a progressive die. The objectives of the current study are to evaluate the die durability of various tooling materials and coatings for forming operations on uncoated DP1180 steel and update OEM’s die standards based on the experimental results in the real production environment. In total, 100,800 hits were performed in manufacturing production conditions, where 33 die inserts with the combination of 10 die materials and 9 coatings were investigated. The die inserts were evaluated for surface wear using scanning electron microscopy and characterized in terms of die material and/or coating defects, failure mode, failure initiation and propagation. Surface roughness of the formed parts was characterized using a WYKO NT110 machine. The analytical analysis of the die inserts and formed parts, combined with the failure mode and service life, provide a basis for die material and coating selection for forming AHSS components. The conclusions of this study will guide the selection of die material and coatings for high-volume production of AHSS components.

Tribological Properties of AlSi12-Al2O3 Interpenetrating Composite Layers in Comparison with Unreinforced Matrix Alloy

PubMed Central

Dolata, Anna Janina

2017-01-01

Alumina–Aluminum composites with interpenetrating network structures are a new class of advanced materials with potentially better properties than composites reinforced by particles or fibers. Local casting reinforcement was proposed to take into account problems with the machinability of this type of materials and the shaping of the finished products. The centrifugal infiltration process fabricated composite castings in the form of locally reinforced shafts. The main objective of the research presented in this work was to compare the tribological properties (friction coefficient, wear resistance) of AlSi12/Al2O3 interpenetrating composite layers with unreinforced AlSi12 matrix areas. Profilometric tests enabled both quantitative and qualitative analyses of the wear trace that formed on investigated surfaces. It has been shown that interpenetrating composite layers are characterized by lower and more stable coefficients of friction (μ), as well as higher wear resistance than unreinforced matrix areas. At the present stage, the study confirmed that the tribological properties of the composite layers depend on the spatial structure of the ceramic reinforcement, and primarily the volume and size of alumina foam cells. PMID:28878162

The influence of micro-scale dimples and nano-sized grains on the fretting characteristics generated by laser pulses.

PubMed

Amanov, Auezhan; Watabe, Tsukasa; Sasaki, Shinya

2013-12-01

The tribological characteristics of micro-scale dimpled Cu-based alloy specimen generated using a laser surface texturing (LST) were assessed and compared with that of the untextured specimen. The objective of this study is to improve the tribological characteristics of internal combustion engine (ICE) bearings and bushings made of Cu-based alloy by generating micro-scale dimples using an LST. Fretting wear tests were performed by sliding a hardened SAE52100 steel ball against the untextured and LSTed specimens at a normal load of 5 N under oil-lubricated conditions. The friction force and relative movement between the specimens were measured simultaneously during the fretting tests. The test results showed that the LSTed specimens showed a reduction in friction coefficient and an enhancement in fretting wear resistance compared to that of the untextured specimen. The friction coefficient and fretting wear volume increased with increasing frequency for both untextured and LSTed specimens. The improved tribological properties of the LSTed specimen may be attributed to the micro-scale dimples, refined grain size and high lattice strain. In addition, a model for the nanocrystallization mechanism of the LSTed specimen was proposed.

A comprehensive and conservative approach for the restoration of abrasion and erosion. Part I: concepts and clinical rationale for early intervention using adhesive techniques.

PubMed

Dietschi, Didier; Argente, Ana

2011-01-01

Tooth wear represents a frequent pathology with multifactorial origins. Behavioral changes, unbalanced diet, various medical conditions and medications inducing acid regurgitation or influencing saliva composition and flow rate, trigger tooth erosion. Awake and sleep bruxism, which are widespread nowadays with functional disorders, induce attrition. It has become increasingly important to diagnose early signs of tooth wear so that proper preventive, and if needed, restorative measures are taken. Such disorders have biological, functional, and also esthetic consequences. Following a comprehensive clinical evaluation, treatment objectives, such as a proper occlusal and anatomical scheme as well as a pleasing smile line, are usually set on models with an anterior teeth full-mouth waxup, depending on the severity of tissue loss. Based on the new vertical dimension of occlusion (VDO), combinations of direct and indirect restorations can then help to reestablish anatomy and function. The use of adhesive techniques and resin composites has demonstrated its potential, in particular for the treatment of moderate tooth wear. Part I of this article reviews recent knowledge and clinical concepts dealing with the various forms of early restorative interventions and their potential to restrict ongoing tissue destruction.

Investigation of Parametric Influence on the Properties of Al6061-SiCp Composite

NASA Astrophysics Data System (ADS)

Adebisi, A. A.; Maleque, M. A.; Bello, K. A.

2017-03-01

The influence of process parameter in stir casting play a major role on the development of aluminium reinforced silicon carbide particle (Al-SiCp) composite. This study aims to investigate the influence of process parameters on wear and density properties of Al-SiCp composite using stir casting technique. Experimental data are generated based on a four-factors-five-level central composite design of response surface methodology. Analysis of variance is utilized to confirm the adequacy and validity of developed models considering the significant model terms. Optimization of the process parameters adequately predicts the Al-SiCp composite properties with stirring speed as the most influencing factor. The aim of optimization process is to minimize wear and maximum density. The multiple objective optimization (MOO) achieved an optimal value of 14 wt% reinforcement fraction (RF), 460 rpm stirring speed (SS), 820 °C processing temperature (PTemp) and 150 secs processing time (PT). Considering the optimum parametric combination, wear mass loss achieved a minimum of 1 x 10-3 g and maximum density value of 2.780g/mm3 with a confidence and desirability level of 95.5%.

Occlusion and Temporomandibular Function among Subjects with Mandibular Distal Extension Removable Partial Dentures

PubMed Central

Creugers, N. H. J.; Witter, D. J.; Van 't Spijker, A.; Gerritsen, A. E.; Kreulen, C. M.

2010-01-01

Objective. To quantify effects on occlusion and temporomandibular function of mandibular distal extension removable partial dentures in shortened dental arches. Methods. Subjects wearing mandibular extension removable partial dentures (n = 25) were compared with subjects with shortened dental arches without extension (n = 74) and with subjects who had worn a mandibular extension removable partial denture in the past (n = 19). Subjects with complete dentitions (n = 72) were controls. Data were collected at baseline and at 3-, 6-, and 9-year observations. Results. Occlusal activity in terms of reported awareness of bruxism and occlusal tooth wear of lower anterior teeth did not differ significantly between the groups. In contrast, occlusal tooth wear of premolars in shortened dental arches with or without extension dentures was significantly higher than in the controls. Differences amongst groups with respect to signs and symptoms related to temporomandibular disorders were not found. Occlusal support of the dentures did not influence anterior spatial relationship. Occlusal contacts of the denture teeth decreased from 70% for second premolars via 50% for first molars, to 30% for second molars. Conclusions. Mandibular distal extension removable partial dentures in moderate shortened dental arches had no effects on occlusion and temporomandibular function. PMID:20671961

Ferrographic analysis of wear particles from sliding elastohydrodynamic experiments

NASA Technical Reports Server (NTRS)

Jones, W. R., Jr.; Nagaraj, H. S.; Winer, W. O.

1978-01-01

The Ferrograph was used to analyze wear debris generated in a sliding elastohydrodynamic contact. The amount of wear debris correlates well with the ratio of film thickness to composite surface roughness (A ratio). The general wear level parameter and the wear severity index yielded similar correlations with average A ratios. Essentially all the generated wear particles were of the normal rubbing wear type. The Ferrograph was more sensitive in detecting the wear debris than was the commonly used emission spectrograph.

Rapid Analyses of Polyetheretherketone Wear Characteristics by Accelerated Wear Testing with Microfabricated Surfaces for Artificial Joint Systems

PubMed Central

Kuo, Chien-Wei

2017-01-01

Wear particle-induced biological responses are the major factors resulting in the loosening and then failure of total joint arthroplasties. It is feasible to improve the lubrication and reduce the wear of artificial joint system. Polyetheretherketone (PEEK) is considered as a potential bearing material due to its mechanical characteristics of resistance to fatigue strain. The PEEK wear particles have been indicated to be involved in biological responses in vitro, and further studies regarding the wear phenomena and wear particle generation are needed. In this study, we have established an accelerated wear testing system with microfabricated surfaces. Various contact pressures and lubricants have been utilized in the accelerated wear tests. Our results showed that increasing contact pressure resulted in an increase of wear particle sizes and wear rate, and the size of PEEK wear particles can be controlled by the feature size of microfabricated surfaces. These results provided the information rapidly about factors that affect the morphology and amount of PEEK wear particles and can be applied in the future for application of PEEK on the biological articulation system. PMID:29230411

In vitro wear of new indirect resin composites.

PubMed

Jain, V; Platt, J A; Moore, B K; Borges, G A

2009-01-01

This in vitro study evaluated the toothbrush abrasion wear, three-body Alabama wear and two-body pin-on-disc wear of four commercial indirect resin composites. Enamel shades of Radica (R), Sculpture Plus (S), Belleglass-NG (B) and Gradia Indirect (G) were used. For measuring wear due to toothbrush abrasion, six specimens of each group were fabricated, then brushed in a toothbrush abrasion machine for 20,000 cycles. Material loss was determined by weighing and conversion to volume loss. Three-body wear was measured on six samples for each group using an Alabama-type wear testing machine for 400,000 cycles. Wear depth was measured with a contact profilometer. For two-body wear, five disc specimens were prepared and tested in a two-body wear-testing machine against hydroxypatite sliders for 25,000 cycles. Data were analyzed with one-way analysis of variance (ANOVA) and Tukey test (alpha=0.05). Wear was the highest in Sculpture Plus by all three methods tested and the lowest wear was observed in Belleglass-NG. No statistical difference in wear was noted from Radica.

Rapid Analyses of Polyetheretherketone Wear Characteristics by Accelerated Wear Testing with Microfabricated Surfaces for Artificial Joint Systems.

PubMed

Su, Chen-Ying; Kuo, Chien-Wei; Fang, Hsu-Wei

2017-01-01

Wear particle-induced biological responses are the major factors resulting in the loosening and then failure of total joint arthroplasties. It is feasible to improve the lubrication and reduce the wear of artificial joint system. Polyetheretherketone (PEEK) is considered as a potential bearing material due to its mechanical characteristics of resistance to fatigue strain. The PEEK wear particles have been indicated to be involved in biological responses in vitro, and further studies regarding the wear phenomena and wear particle generation are needed. In this study, we have established an accelerated wear testing system with microfabricated surfaces. Various contact pressures and lubricants have been utilized in the accelerated wear tests. Our results showed that increasing contact pressure resulted in an increase of wear particle sizes and wear rate, and the size of PEEK wear particles can be controlled by the feature size of microfabricated surfaces. These results provided the information rapidly about factors that affect the morphology and amount of PEEK wear particles and can be applied in the future for application of PEEK on the biological articulation system.

The in vitro wear behavior of experimental resin-based composites derived from a commercial formulation.

PubMed

Finlay, Nessa; Hahnel, Sebastian; Dowling, Adam H; Fleming, Garry J P

2013-04-01

To investigate the short- and long-term in vitro wear resistance of experimental resin-based composites (RBCs) derived from a commercial formulation. Six experimental RBCs were manufactured by manipulating the monomeric resin composition and the filler characteristics of Grandio (Voco GmbH, Cuxhaven, Germany). The Oregon Health Sciences University (OHSU) oral wear simulator was used in the presence of a food-like slurry to simulate three-body abrasion and attrition wear for 50,000, 150,000 and 300,000 cycles. A three-dimensional image of each wear facet was created and the total volumetric wear (mm(3)) and maximum wear depth (μm) were quantified for the RBC and antagonist. Statistical analyses of the total volumetric wear and maximum wear depth data (two- and one-way analyses of variance (ANOVA), with Tukey's post hoc tests where required) and regression analyses, were conducted at p=0.05. Two-way ANOVAs identified a significant effect of RBC material×wear cycles, RBC material and wear cycles (all p<0.0001). Regression analyses showed significant increases in the total volumetric wear (p≤0.001) and maximum wear depth data (p≤0.004) for all RBCs with increasing wear cycles. Differences between all RBC materials were evident after ≥150,000 wear cycles and antagonist wear provided valuable information to support the experimental findings. Wear simulating machines can provide an indication of the clinical performance but clinical performance is multi-factorial and wear is only a single facet. Employing experimental RBCs provided by a dental manufacturer rather than using self-manufactured RBCs or dental products provides increased experimental control by limiting the variables involved. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Demonstrating the effectiveness of body armour: a pilot prospective computerised surface wound mapping trial performed at the Role 3 hospital in Afghanistan.

PubMed

Breeze, Johno; Allanson-Bailey, L S; Hepper, A E; Midwinter, M J

2015-03-01

Modern body armour clearly reduces injury incidence and severity, but evidence to actually objectively demonstrate this effect is scarce. Although the Joint Theatre Trauma Registry (JTTR) alone cannot relate injury pattern to body armour coverage, the addition of computerised Surface Wound Mapping (SWM) may enable this utility. Surface wound locations of all UK and NATO coalition soldiers, Afghan National Army and Police and local nationals injured by explosively propelled fragments and treated in the Role 3 UK-led Field Hospital in Camp Bastion, Afghanistan, between 8 July and 20 October 2012 were prospectively recorded. The Abbreviated Injury Scores (AIS) and relative risk of casualties sustaining injuries under a type of body armour were compared with those that did not wear that armour. Casualties wearing a combat helmet were 2.7 times less likely to sustain a fragmentation wound to the head than those that were unprotected (mean AIS of 2.9 compared with 4.1). Casualties wearing a body armour vest were 4.1 times less likely to sustain a fragmentation wound to the chest or abdomen than those that were unprotected (mean AIS of 2.9 compared with 3.9). Casualties wearing pelvic protection were 10 times less likely to sustain a fragmentation wound to the pelvis compared with those that were unprotected (mean AIS of 3.4 compared with 3.9). Computerised SWM has objectively demonstrated the ability of body armour worn on current operations in Afghanistan to reduce wound incidence and severity. We recognise this technique is limited in that it only records the surface wound location and may be specific to this conflict. However, gathering electronic SWM at the same time as recording injuries for the JTTR was simple, required little extra time and therefore we would recommend its collection during future conflicts. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Cadmium content of Cameroonian cigarettes: Comparison with other foreign brands sold in Cameroon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tamboue, H.S.; Tamboue, E.D.; Leno, M.

Given the increasing concern about heavy metal and in particular cadmium toxicity, the present study has two objectives. First, the authors wanted to measure and compare the amount of cadmium found in Cameroonian cigarettes and in foreign brands sold in Cameroon. Secondly, they measured the amount of cadmium in smoke, ashes and the amount retained by filters of some Cameroonian cigarettes after using a smoking machine.

Planeamiento de la unidad didactica en le ensenanza del ingles como idioma extranjero (Planning the Teaching Unit in the Instruction of English as a Foreign Language).

ERIC Educational Resources Information Center

Medina T., Rene

1971-01-01

This paper discusses the use of the teaching unit as a means for organization in English-as-a-foreign-language classes. It lists the essential elements in the construction of such a unit: cultural topic, linguistic elements, time period, main objectives, instructional materials, focus, specific activities, intended results, evaluation techniques,…

Strategy for Peace 1984. The Stanley Foundation US Foreign Policy Conference Report (25th, Annapolis, Maryland, October 11-13, 1984).

ERIC Educational Resources Information Center

Stanley Foundation, Muscatine, IA.

Proceedings are summarized of a conference in which 62 foreign policy professionals met to recommend strategies for peace in the areas of U.S.-Soviet competition in the Third World, space weapons and arms control, objectives of U.S. economic and security assistance, and the United States and UNESCO. Four sections focusing on each of these areas…

Boys' and Girls' Attribution of Performance in Learning English as a Foreign Language: The Case of Adama High Schools in Ethiopia

ERIC Educational Resources Information Center

Tulu, Geberew

2013-01-01

The main aim of the study was to examine students' attribution of performance in learning English as a foreign language at Adama town government high schools and see into its pedagogical implications. It aimed at investigating the perceived causes of success and failure of boys and girls. In order to meet the objectives of the study, data were…

Low friction wear resistant graphene films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sumant, Anirudha V.; Berman, Diana; Erdemir, Ali

A low friction wear surface with a coefficient of friction in the superlubric regime including graphene and nanoparticles on the wear surface is provided, and methods of producing the low friction wear surface are also provided. A long lifetime wear resistant surface including graphene exposed to hydrogen is provided, including methods of increasing the lifetime of graphene containing wear surfaces by providing hydrogen to the wear surface.

Application of GIS in foreign direct investment decision support system

NASA Astrophysics Data System (ADS)

Zhou, Jianlan; Sun, Koumei

2007-06-01

It is important to make decisions on how to attract foreign direct investment (FDI) to China and know how the inequality of FDI introduction by locational different provinces. Following background descriptions on China's FDI economic environments and FDI-related policies, this paper demonstrates the uses of geographical information system (GIS) and multi-criterion decision-making (MCDM) framework in solving a spatial multi-objective problem of evaluating and ranking China's provinces for FDI introduction. It implements a foreign direct investment decision support system, which reveals the main determinants of FDI in China and gives some results of regional geographical analysis over spatial data.

Septic arthritis due to Cellulosimicrobium cellulans.

PubMed

Magro-Checa, César; Chaves-Chaparro, Lara; Parra-Ruiz, Jorge; Peña-Monje, Alejandro; Rosales-Alexander, José Luis; Salvatierra, Juan; Raya, Enrique

2011-12-01

Cellulosimicrobium cellulans has been reported as a rare cause of human pathogenesis. Infections mainly occur in immunocompromised patients and very often are associated with a foreign body. We report the first case of septic arthritis caused by C. cellulans in an immunocompetent patient. Our patient suffered a penetrating palm tree thorn injury to his left knee 8 weeks before admission. Although no foreign objects were found, they were suspected because previous reports suggest a frequent association with this microorganism, and open debridament was performed. Removal of foreign bodies related to this organism must be considered a high-priority treatment in these patients to achieve a complete recovery.

Low-energy impact resistance of graphite-epoxy plates and ALS honeycomb sandwich panels

NASA Technical Reports Server (NTRS)

Hui, David

1989-01-01

Low energy impact may be potentially dangerous for many highly optimized stiff structures. Impact by foreign objects such as birds, ice, and runways stones or dropping of tools occur frequently and the resulting damage and stress concentrations may be unacceptable from a designer's standpoint. The barely visible, yet potentially dangerous dents due to impact of foreign objects on the Advanced Launch System (ALS) structure are studied. Of particular interest is the computation of the maximum peak impact force for a given impactor mass and initial velocity. The theoretical impact forces will be compared with the experimental dropweight results for the ALS face sheets alone as well as the ALS honeycomb sandwich panels.

Detecting of foreign object debris on airfield pavement using convolution neural network

NASA Astrophysics Data System (ADS)

Cao, Xiaoguang; Gu, Yufeng; Bai, Xiangzhi

2017-11-01

It is of great practical significance to detect foreign object debris (FOD) timely and accurately on the airfield pavement, because the FOD is a fatal threaten for runway safety in airport. In this paper, a new FOD detection framework based on Single Shot MultiBox Detector (SSD) is proposed. Two strategies include making the detection network lighter and using dilated convolution, which are proposed to better solve the FOD detection problem. The advantages mainly include: (i) the network structure becomes lighter to speed up detection task and enhance detection accuracy; (ii) dilated convolution is applied in network structure to handle smaller FOD. Thus, we get a faster and more accurate detection system.

Surface chemistry of iron sliding in air and nitrogen lubricated with hexadecane and hexadecane containing dibenzyl-dilsulfide

NASA Technical Reports Server (NTRS)

Wheeler, D. R.

1979-01-01

Wear experiments were conducted on iron sliding in hexadecane and hexadecane plus one weight percent dibenzyl dilsulfide (DBDS) in atmospheres of air and nitrogen at room temperature. The wear scars and the wear debris were analyzed by X-ray photoelectron spectroscopy. The presence of air reduced wear but increased friction, while DBDS reduced friction but had little effect on wear except that the wear increased somewhat when DBDS was used in air. Wear scar analysis indicated that oxygen and sulfur competed chemically for the surface, with the oxide predominating. Low wear was associated with a thick oxide layer and low friction with a thin predominantly sulfide layer. Analysis of the wear debris indicated the presence of a sulfate in the high wear case (hexadecane plus DBDS in air), and showed the presence of an organic sulfide in the low wear case (Hexadecane plus DBDS in nitrogen).

How do gait frequency and serum-replacement interval affect polyethylene wear in knee-wear simulator tests?

PubMed

Reinders, Jörn; Sonntag, Robert; Kretzer, Jan Philippe

2014-11-01

Polyethylene wear (PE) is known to be a limiting factor in total joint replacements. However, a standardized wear test (e.g. ISO standard) can only replicate the complex in vivo loading condition in a simplified form. In this study, two different parameters were analyzed: (a) Bovine serum, as a substitute for synovial fluid, is typically replaced every 500,000 cycles. However, a continuous regeneration takes place in vivo. How does serum-replacement interval affect the wear rate of total knee replacements? (b) Patients with an artificial joint show reduced gait frequencies compared to standardized testing. What is the influence of a reduced frequency? Three knee wear tests were run: (a) reference test (ISO), (b) testing with a shortened lubricant replacement interval, (c) testing with reduced frequency. The wear behavior was determined based on gravimetric measurements and wear particle analysis. The results showed that the reduced test frequency only had a small effect on wear behavior. Testing with 1 Hz frequency is therefore a valid method for wear testing. However, testing with a shortened replacement interval nearly doubled the wear rate. Wear particle analysis revealed only small differences in wear particle size between the different tests. Wear particles were not linearly released within one replacement interval. The ISO standard should be revised to address the marked effects of lubricant replacement interval on wear rate.

Clinical Biomechanics of Wear in Total Hip Arthroplasty

PubMed Central

Callaghan, John J; Pedersen, Douglas R; Johnston, Richard C; Brown, Thomas D

2003-01-01

Complementary clinical and laboratory studies were performed to identify variables associated with polyethylene wear following total hip replacement, and to elucidate the mechanisms responsible for accelerated wear in the total hip arthroplasty construct. Observational cohort studies were performed using a prospective clinical database of more than 4000 consecutive primary total hip arthroplasties performed by a single surgeon, to identify wear-related variables. These variables included head size, acetabular/femoral component impingement, and third body debris. Novel digital edge detection techniques were developed and employed to accurately measure wear, and to determine the relationships of head size and third body debris to acceleration of wear. A novel slidingdistance-coupled finite element model was formulated and employed to examine the mechanisms responsible for wear. The long-term cohort studies demonstrated smaller head sizes to be associated with less wear. Third body debris generated from cable fretting was associated with an increase in wear, osteolysis, and acetabular loosening, especially with larger head sizes. The sliding-distance-coupled finite element model replicated the wear rates occurring in vitro and in vivo, demonstrating the importance of sliding distance on polyethylene wear following total hip arthroplasty. It also demonstrated substantial increases in wear associated with femoral head scratching from third body debris. Further extension of the finite element formulation demonstrated the potential for acetabular component rim damage from impingement wear, and the enhanced potential for third body ingress to the bearing surface with larger head sizes. Edge detection wear measurement techniques demonstrated that early wear rates were predictive of long-term wear rates. These complementary clinical and laboratory investigations have provided insight into 1) the significance of sliding distance and physiologic loci of motion as contributing factors in minimizing wear, 2) the deleterious effects of third body particulates in accelerating wear, 3) the potential for, and factors related to, impingement wear, and 4) the potential advantages and compromises related to the use of larger head sizes in the bearing surface construct. PMID:14575243

Combating pharmacist shortage through labor certification.

PubMed

Maswoswe, J J; Stewart, K R; Enigbokan, M; Egbunike, I; Jackson, D M

1994-06-01

Several solutions, ranging from increased technician duties to salary raises, automation, and increasing job satisfaction, have been presented in the literature as methods of assuaging the pharmacist shortage. Although a significant portion of pharmacy graduates from American pharmacy colleges are foreign nationals, no marketing strategies have been elucidated in the retention and recruitment of foreign nationals through labor certification. Labor certifications are generally approved by the Secretary of Labor if the following factors have been verified: 1) there are not sufficient United States workers who are able, willing, qualified, and available for employment; and 2) the employment of the foreign national will not adversely affect the wages and working conditions of U.S. workers similarly employed. When properly understood, the labor certification process is a test of the job market where foreigners, by virtue of their skills and qualifications, attain certification which subsequently leads to permanent residency (green card). The objective of this report is to elucidate the tedious yet effective method of retaining American-educated foreign nationals through labor certification.

Pakistan: Frontline state again. Master`s thesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rivard, D.S.

1995-12-01

The objective of this study is to determine Pakistan`s place in contemporary U.S. national security strategy. Today, U.S.-Pakistan relations are strained due to the Pressler Amendment to the Foreign Assistance Act. The Pressler Amendment prohibits arms transfers from the United States to Pakistan in response to Pakistani efforts to develop a nuclear weapon capability. This thesis provides a historical background to the current impasse by examining Pakistani foreign policy since 1947. Next, the study examines the evolution of U.S. interests and security objectives in South and Southwest Asia. Current security objectives analyzed are the U.S. strategies to contain Iran andmore » Iraq and to prevent nuclear proliferation in the region. In order to attain security objectives in the region, the author concludes that the U.S. needs a close cooperative relationship with Pakistan. Since the Pressler Amendment stands as the greatest obstacle to improved U.S.-Pakistan relations, the amendment should be repealed.« less

Anti-wear Mechanism Analysis of Nano-CaCO3 Additives

NASA Astrophysics Data System (ADS)

Xu, Zhen; Sun, Junfeng

2018-06-01

In this paper, the wear test was carried on with cylinder piston by the wear test device, receiving the results of the piston ring wear and abrasive characteristics by monitoring the wear process, the thesis analysis and put forward the nano-CaCO3 lubricating oil additive anti wear mechanism by the ferrography analysis technology, and provide the technical reference for the relevant measures to reduce wear and the friction, and provide reference value for further study on the related theories of reducing wear and reducing friction.

Understanding wear in dentistry.

PubMed

Mair, L H

1999-01-01

Tooth wear is an increasing problem in dentistry. Traditionally, it has been divided into three categories: abrasion, attrition, and erosion. However, most clinical cases of tooth wear involve more than one of these processes. It is often easier to make a diagnosis by looking for the signs of the fundamental wear processes rather than trying to categorize the individual case. Wear can be caused by direct surface-to-surface wear, an intervening slurry, or a corrosive environment. Wear occurs during mastication, but also at other times, often at night. Although it may be possible to institute a preventive regimen, this will not always help the patient if his or her prime concern is esthetics. The same processes that cause tooth wear will cause wear to restorative materials. To diagnose and prevent wear, its processes must be understood.

Mobile-bearing knees reduce rotational asymmetric wear.

PubMed

Ho, Fang-Yuan; Ma, Hon-Ming; Liau, Jiann-Jong; Yeh, Chuan-Ren; Huang, Chun-Hsiung

2007-09-01

Polyethylene wear of bearing components is the most common long-term complication in total knee arthroplasty. One would anticipate differing kinematics would generate different wear patterns (including wear type, degree, and symmetry) on the articulating surface of mobile-bearing and fixed-bearing inserts. Because mobile-bearing designs facilitate movement of the insert relative to the tray when the knee rotates, we hypothesized mobile-bearing designs would reduce the incidence of rotational asymmetric wear. We examined 51 worn tibial inserts, including 15 from mobile-bearing rotating-platform posterior-cruciate-sacrificing dished prostheses and 36 from fixed-bearing posterior-cruciate-retaining flat prostheses, which were retrieved at revision surgery with an average implantation time of 115 months. We divided wear types into low-grade wear (burnishing, abrasion, and cold flow) and high-grade wear (scratching, pitting, metal embedding, and delamination) to assess wear degree of polyethylene. To assess symmetry of wear, the insert surface was divided into medial and lateral sides and each side was further divided into three equal zones along the anteroposterior direction. Low-grade wear was more common in mobile-bearing knees, whereas high-grade wear was more common in fixed-bearing knees. We identified no internal/external rotational asymmetric wear or anteroposterior asymmetric wear in mobile-bearing knees.

A comparative study of sliding wear of nonmetallic dental restorative materials with emphasis on micromechanical wear mechanisms.

PubMed

Dupriez, Nataliya Deyneka; von Koeckritz, Ann-Kristin; Kunzelmann, Karl-Heinz

2015-05-01

The purpose of this study is to investigate the in vitro tribological behavior of modern nonmetallic restorative materials. Specimen prepared of IPS e.max Press lithium disilicate glass ceramic, IPS Empress Esthetic leucite-reinforced glass ceramic, Everest ZS Blanks yttria-stabilized zirconia and Lava Ultimate composite were subjected to wear using a wear machine designed to simulate occlusal loads. The wear of the investigated materials and antagonists were evaluated by a three-dimensional surface scanner. The quantitative wear test results were used to compare and rank the materials. Specimens were divided into two groups with steatite and alumina antagonists. For each antagonist material an analysis of variance was applied. As a post hoc test of the significant differences, Tukey's honest significant difference test was used. With steatite antagonist: wear of zirconia < wear of leucite-reinforced ceramic < wear of lithium disilicate ceramic < wear of Lava Ultimate composite. No significant wear difference was found for steatite antagonist. The wear of IPS e.max Press and Lava Ultimate against hard alumina was found to be twice lower as compared to their wear when opposing to steatite. The differences were associated with materials mechanical properties (hardness and fracture toughness) and with materials microstructure. Wear mechanisms are discussed. © 2014 Wiley Periodicals, Inc.

The response of macrophages to titanium particles is determined by macrophage polarization.

PubMed

Pajarinen, Jukka; Kouri, Vesa-Petteri; Jämsen, Eemeli; Li, Tian-Fang; Mandelin, Jami; Konttinen, Yrjö T

2013-11-01

Aseptic loosening of total joint replacements is driven by the reaction of macrophages to foreign body particles released from the implant. It was hypothesized that the macrophages' response to these particles is dependent, in addition to particle characteristics and contaminating biomolecules, on the state of macrophage polarization as determined by the local cytokine microenvironment. To test this hypothesis we differentiated M1 and M2 macrophages from human peripheral blood monocytes and compared their responses to titanium particles using genome-wide microarray analysis and a multiplex cytokine assay. In comparison to non-activated M0 macrophages, the overall chemotactic and inflammatory responses to titanium particles were greatly enhanced in M1 macrophages and effectively suppressed in M2 macrophages. In addition, the genome-wide approach revealed several novel, potentially osteolytic, particle-induced mediators, and signaling pathway analysis suggested the involvement of toll-like and nod-like receptor signaling in particle recognition. It is concluded that the magnitude of foreign body reaction caused by titanium particles is dependent on the state of macrophage polarization. Thus, by limiting the action of M1 polarizing factors, e.g. bacterial biofilm formation, in peri-implant tissues and promoting M2 macrophage polarization by biomaterial solutions or pharmacologically, it might be possible to restrict wear-particle-induced inflammation and osteolysis. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Tibiofemoral wear in standard and non-standard squat: implication for total knee arthroplasty.

PubMed

Fekete, Gusztáv; Sun, Dong; Gu, Yaodong; Neis, Patric Daniel; Ferreira, Ney Francisco; Innocenti, Bernardo; Csizmadia, Béla M

2017-01-01

Due to the more resilient biomaterials, problems related to wear in total knee replacements (TKRs) have decreased but not disappeared. In the design-related factors, wear is still the second most important mechanical factor that limits the lifetime of TKRs and it is also highly influenced by the local kinematics of the knee. During wear experiments, constant load and slide-roll ratio is frequently applied in tribo-tests beside other important parameters. Nevertheless, numerous studies demonstrated that constant slide-roll ratio is not accurate approach if TKR wear is modelled, while instead of a constant load, a flexion-angle dependent tibiofemoral force should be involved into the wear model to obtain realistic results. A new analytical wear model, based upon Archard's law, is introduced, which can determine the effect of the tibiofemoral force and the varying slide-roll on wear between the tibiofemoral connection under standard and non-standard squat movement. The calculated total wear with constant slide-roll during standard squat was 5.5 times higher compared to the reference value, while if total wear includes varying slide-roll during standard squat, the calculated wear was approximately 6.25 times higher. With regard to non-standard squat, total wear with constant slide-roll during standard squat was 4.16 times higher than the reference value. If total wear included varying slide-roll, the calculated wear was approximately 4.75 times higher. It was demonstrated that the augmented force parameter solely caused 65% higher wear volume while the slide-roll ratio itself increased wear volume by 15% higher compared to the reference value. These results state that the force component has the major effect on wear propagation while non-standard squat should be proposed for TKR patients as rehabilitation exercise.

Tibiofemoral wear in standard and non-standard squat: implication for total knee arthroplasty

PubMed Central

Sun, Dong; Gu, Yaodong; Neis, Patric Daniel; Ferreira, Ney Francisco; Innocenti, Bernardo; Csizmadia, Béla M.

2017-01-01

Summary Introduction Due to the more resilient biomaterials, problems related to wear in total knee replacements (TKRs) have decreased but not disappeared. In the design-related factors, wear is still the second most important mechanical factor that limits the lifetime of TKRs and it is also highly influenced by the local kinematics of the knee. During wear experiments, constant load and slide-roll ratio is frequently applied in tribo-tests beside other important parameters. Nevertheless, numerous studies demonstrated that constant slide-roll ratio is not accurate approach if TKR wear is modelled, while instead of a constant load, a flexion-angle dependent tibiofemoral force should be involved into the wear model to obtain realistic results. Methods A new analytical wear model, based upon Archard’s law, is introduced, which can determine the effect of the tibiofemoral force and the varying slide-roll on wear between the tibiofemoral connection under standard and non-standard squat movement. Results The calculated total wear with constant slide-roll during standard squat was 5.5 times higher compared to the reference value, while if total wear includes varying slide-roll during standard squat, the calculated wear was approximately 6.25 times higher. With regard to non-standard squat, total wear with constant slide-roll during standard squat was 4.16 times higher than the reference value. If total wear included varying slide-roll, the calculated wear was approximately 4.75 times higher. Conclusions It was demonstrated that the augmented force parameter solely caused 65% higher wear volume while the slide-roll ratio itself increased wear volume by 15% higher compared to the reference value. These results state that the force component has the major effect on wear propagation while non-standard squat should be proposed for TKR patients as rehabilitation exercise. PMID:29721453

An analysis of contact stiffness between a finger and an object when wearing an air-cushioned glove: the effects of the air pressure.

PubMed

Wu, John Z; Wimer, Bryan M; Welcome, Daniel E; Dong, Ren G

2012-04-01

Air-cushioned gloves have the advantages of lighter weight, lower cost, and unique mechanical performance, compared to gloves made of conventional engineering materials. The goal of this study is to analyze the contact interaction between fingers and object when wearing an air-cushioned glove. The contact interactions between the the fingertip and air bubbles, which is considered as a cell of a typical air-cushioned glove, has been analyzed theoretically. Two-dimensional finite element models were developed for the analysis. The fingertip model was assumed to be composed of skin layers, subcutaneous tissue, bone, and nail. The air bubbles were modeled as air sealed in the container of nonelastic membrane. We simulated two common scenarios: a fingertip in contact with one single air bubble and with two air cushion bubbles simultaneously. Our simulation results indicated that the internal air pressure can modulate the fingertip-object contact characteristics. The contact stiffness reaches a minimum when the initial air pressure is equal to 1.3 and 1.05 times of the atmosphere pressure for the single air bubble and the double air bubble contact, respectively. Furthermore, the simulation results indicate that the double air bubble contact will result in smaller volumetric tissue strain than the single air bubble contact for the same force. Published by Elsevier Ltd.

Wear Behavior of an Ultra-High-Strength Eutectoid Steel

NASA Astrophysics Data System (ADS)

Mishra, Alok; Maity, Joydeep

2018-02-01

Wear behavior of an ultra-high-strength AISI 1080 steel developed through incomplete austenitization-based combined cyclic heat treatment is investigated in comparison with annealed and conventional hardened and tempered conditions against an alumina disk (sliding speed = 1 m s-1) using a pin-on-disk tribometer at a load range of 7.35-14.7 N. On a gross scale, the mechanism of surface damage involves adhesive wear coupled with abrasive wear (microcutting effects in particular) at lower loads. At higher loads, mainly the abrasive wear (both microcutting and microploughing mechanisms) and evolution of adherent oxide are observed. Besides, microhardness of matrix increases with load indicating substantial strain hardening during wear test. The rate of overall wear is found to increase with load. As-received annealed steel with the lowest initial hardness suffers from severe abrasive wear, thereby exhibiting the highest wear loss. Such a severe wear loss is not observed in conventional hardened and tempered and combined cyclic heat treatment conditions. Combined cyclic heat-treated steel exhibits the greatest wear resistance (lowest wear loss) due to its initial high hardness and evolution of hard abrasion-resistant tribolayer during wear test at higher load.

Wear simulation of resin composites and the relationship to clinical wear.

PubMed

Barkmeier, Wayne W; Latta, Mark A; Erickson, Robert L; Wilwerding, Terry M

2008-01-01

This study used a new generalized wear model to examine the relationship between wear simulation and the clinical wear of two resin composites. Ten specimens each of P50 and Z100, were subjected to 100,000, 400,000 and 800,000 cycles in a spring-loaded piston-type wear simulator. Wear was generated using flat, cylindrically-shaped stainless steel antagonists on the resin composites, which were placed in custom stainless steel fixtures. A slurry of polymethyl methacrylate beads was used as the abrasive media. Wear was determined using profilometry, and the parameters examined included volume loss (mm3), maximum depth (microm), mean maximum depth (microm) and mean depth (microm). Statistical analysis of the laboratory wear data using ANOVA and Tukey's post hoc test showed a significant difference (p<0.05) for wear between the two materials and the number of cycles. Mean maximum wear (microm) values (100K--P50--11.5 +/- 1.8; Z100--4.9 +/- 1.0; 400K--P50--17.2 +/- 2.7; Z100--6.0 +/- 1.7; 800K--P50--20.5 +/- 4.6; Z100--9.6 +/- 2.5) were used for comparisons with clinical data. Previous clinical studies of P50 and Z100 were used to examine the relationship between laboratory and clinical wear. Linear regression analysis was used to predict laboratory and clinical wear rates. The laboratory wear rate for P50 was 1.3 microm/100K cycles and the rate for Z100 was 0.7 microm/100K cycles. The clinical wear rates for P50 and Z100 were 8.3 microm/year and 4.0 microm/year, respectively. The ratio of wear rates of P50 to Z100 for wear simulation was 1.9 and the ratio of P50 to Z100 for clinical rates was 2.1. These ratios showed good agreement between the relative wear rates of laboratory and clinical wear. For the two composite materials examined, this new simulation model appears to be effective for evaluating the relative wear of resin composites.

X-ray photoelectron spectroscopic study of surface chemistry of dibenzyl-disulfide on steel under mild and severe wear conditions

NASA Technical Reports Server (NTRS)

Wheeler, D. R.

1977-01-01

Wear tests were performed on 304 stainless steel lubricated with pure mineral oil with and without dibenzyl-disulfide. Both mild and severe wear were observed. The type of wear was distinguished by a marked change in wear rate, friction coefficient, and wear scar appearance. The chemical composition of the wear scar surface was examined with X-ray photoelectron spectroscopy in conjunction with argon ion sputter etching. In severe wear scars, a sulfide was formed at the expense of the normal oxide layer. In mild wear scars, there were only superficial sulfur compounds, but there was a substantial increase in the oxide thickness.

Assessment of wear dependence parameters in complex model of cutting tool wear

NASA Astrophysics Data System (ADS)

Antsev, A. V.; Pasko, N. I.; Antseva, N. V.

2018-03-01

This paper addresses wear dependence of the generic efficient life period of cutting tools taken as an aggregate of the law of tool wear rate distribution and dependence of parameters of this law's on the cutting mode, factoring in the random factor as exemplified by the complex model of wear. The complex model of wear takes into account the variance of cutting properties within one batch of tools, variance in machinability within one batch of workpieces, and the stochastic nature of the wear process itself. A technique of assessment of wear dependence parameters in a complex model of cutting tool wear is provided. The technique is supported by a numerical example.

A Foreign Object Damage Event Detector Data Fusion System for Turbofan Engines

NASA Technical Reports Server (NTRS)

Turso, James A.; Litt, Jonathan S.

2004-01-01

A Data Fusion System designed to provide a reliable assessment of the occurrence of Foreign Object Damage (FOD) in a turbofan engine is presented. The FOD-event feature level fusion scheme combines knowledge of shifts in engine gas path performance obtained using a Kalman filter, with bearing accelerometer signal features extracted via wavelet analysis, to positively identify a FOD event. A fuzzy inference system provides basic probability assignments (bpa) based on features extracted from the gas path analysis and bearing accelerometers to a fusion algorithm based on the Dempster-Shafer-Yager Theory of Evidence. Details are provided on the wavelet transforms used to extract the foreign object strike features from the noisy data and on the Kalman filter-based gas path analysis. The system is demonstrated using a turbofan engine combined-effects model (CEM), providing both gas path and rotor dynamic structural response, and is suitable for rapid-prototyping of control and diagnostic systems. The fusion of the disparate data can provide significantly more reliable detection of a FOD event than the use of either method alone. The use of fuzzy inference techniques combined with Dempster-Shafer-Yager Theory of Evidence provides a theoretical justification for drawing conclusions based on imprecise or incomplete data.

Global Positioning System Derived Performance Measures Are Responsive Indicators of Physical Activity, Disease and the Success of Clinical Treatments in Domestic Dogs

PubMed Central

Bruno, Elizabeth A.; Guthrie, James W.; Ellwood, Stephen A.; Mellanby, Richard J.; Clements, Dylan N.

2015-01-01

Objective To assess the use of Global Positioning System receiver (GPS) derived performance measures for differentiating between: 1) different outdoor activities in healthy dogs; 2) healthy dogs and those with osteoarthritis; 3) osteoarthritic dogs before and after treatment with non-steroidal anti-inflammatory analgesia. Design Prospective study. Animals Ten healthy dogs and seven dogs with osteoarthritis of the elbow joint (OA dogs). Procedure Healthy dogs were walked on a standard route on-lead, off-lead and subjected to playing activity (chasing a ball) whilst wearing a GPS collar. Each dog was walked for five consecutive days. Dogs with OA were subjected to a single off-lead walk whilst wearing a GPS collar, and then administered oral Carprofen analgesia daily for two weeks. OA dogs were then subjected to the same walk, again wearing a GPS collar. Results GPS derived measures of physical performance could differentiate between on-lead activity, off-lead activity and playing activity in healthy dogs, and between healthy dogs and OA dogs. Variation in the performance measures analysed was greater between individual dogs than for individual dogs on different days. Performance measures could differentiate healthy dogs from OA dogs. OA Dogs treated with Carprofen analgesia showed improvements in their physical performance, which returned to values indistinguishable from those of healthy dogs on nearly all the measures assessed. Conclusions and Clinical Relevance GPS derived measures of physical performance in dogs are objective, easy to quantify, and can be used to gauge the effects of disease and success of clinical treatments. Specific stimuli can be used to modulate physical performance beyond the self-governed boundaries that dogs will naturally express when allowed to exercise freely without stimulation. PMID:25692761

The influence of end of day silicone hydrogel daily disposable contact lens fit on ocular comfort, physiology and lens wettability.

PubMed

Wolffsohn, James; Hall, Lee; Mroczkowska, Stephanie; Hunt, Olivia A; Bilkhu, Paramdeep; Drew, Tom; Sheppard, Amy

2015-10-01

To quantify the end-of-day silicone-hydrogel daily disposable contact lens fit and its influence of on ocular comfort, physiology and lens wettability. Thirty-nine subjects (22.1±3.5 years) were randomised to wear each of 3 silicone-hydrogel daily-disposable contact lenses (narafilcon A, delefilcon A and filcon II 3), bilaterally, for one week. Lens fit was assessed objectively using a digital video slit-lamp at 8, 12 and 16h after lens insertion. Hyperaemia, non-invasive tear break-up time, tear meniscus height and comfort were also evaluated at these timepoints, while corneal and conjunctival staining were assessed on lens removal. Lens fit assessments were not different between brands (P>0.05), with the exception of the movement at blink where narafilcon A was more mobile. Overall, lag reduced but push-up speed increased from 8 to 12h (P<0.05), but remained stable from 12 to 16h (P>0.05). Movement-on-blink was unaffected by wear-time (F=0.403, P=0.670). A more mobile lens fit with one brand did not indicate that person would have a more mobile fit with another brand (r=-0.06 to 0.63). Lens fit was not correlated with comfort, ocular physiology or lens wettability (P>0.01). Among the lenses tested, objective lens fit changed between 8h and 12h of lens wear. The weak correlation in individual lens fit between brands indicates that fit is dependent on more than ocular shape. Consequently, substitution of a different lens brand with similar parameters will not necessarily provide comparable lens fit. Copyright © 2015 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

Friction and wear behaviour of ion beam modified ceramics

NASA Technical Reports Server (NTRS)

Lankford, J.; Wei, W.; Kossowsky, R.

1987-01-01

In the present study, the sliding friction coefficients and wear rates of carbide, oxide, and nitride materials for potential use as sliding seals (ring/liner) were measured under temperature, environmental, velocity, and loading conditions representative of a diesel engine. In addition, silicon nitride and partially stabilized zirconia discs were modified by ion mixing with TiNi, nickel, cobalt and chromium, and subsequently run against carbide pins, with the objective of producing reduced friction via solid lubrication at elevated temperature. Unmodified ceramic sliding couples were characterized at all temperatures by friction coefficients of 0.24 and above. However, the coefficient at 800 C in an oxidizing environment was reduced to below 0.1, for certain material combinations, by the ion implantation of TiNi or cobalt. This beneficial effect was found to derive from lubricious titanium, nickel, and cobalt oxides.

Numerical analysis and experimental studies on solenoid common rail diesel injector with worn control valve

NASA Astrophysics Data System (ADS)

Krivtsov, S. N.; Yakimov, I. V.; Ozornin, S. P.

2018-03-01

A mathematical model of a solenoid common rail fuel injector was developed. Its difference from existing models is control valve wear simulation. A common rail injector of 0445110376 Series (Cummins ISf 2.8 Diesel engine) produced by Bosch Company was used as a research object. Injector parameters (fuel delivery and back leakage) were determined by calculation and experimental methods. GT-Suite model average R2 is 0.93 which means that it predicts the injection rate shape very accurately (nominal and marginal technical conditions of an injector). Numerical analysis and experimental studies showed that control valve wear increases back leakage and fuel delivery (especially at 160 MPa). The regression models for determining fuel delivery and back leakage effects on fuel pressure and energizing time were developed (for nominal and marginal technical conditions).

Ceramic technology for advanced heat engines project. Semiannual progress report, April-September 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1986-05-01

An assessment of needs was completed, and a five-year project plan was developed with input from private industry. Objective is to develop the industrial technology base required for reliable ceramics for application in advanced automotive heat engines. Focus is on structural ceramics for advanced gas turbine and diesel engines, ceramic bearings and attachments, and ceramic coatings for thermal barrier and wear applications in these engines. The work described in this report is organized according to the following WBS project elements: management and coordination; materials and processing (monolithics, ceramic composites, thermal and wear coatings, joining); materials design methodology (contact interfaces, newmore » concepts); data base and life prediction (time-dependent behavior, environmental effects, fracture mechanics, NDE development); and technology transfer. This report includes contributions from all currently active project participants.« less

The friction and wear of carbon-carbon composites for aircraft brakes

NASA Astrophysics Data System (ADS)

Hutton, Toby

Many carbon-carbon composite aircraft brakes encounter high wear rates during low energy braking operations. The work presented in this thesis addresses this issue, but it also elucidates the microstructural changes and wear mechanisms that take place in these materials during all braking conditions encountered by aircraft brakes. A variety of investigations were conducted using friction and wear testing, as well as examination of wear surfaces and wear debris using OM, SEM, X-RD, TGA and Density Gradient Separation (DOS). Friction and wear tests were conducted on a PAN fibre/CVI matrix carbon-carbon composite (Dunlop) and a pitch fibre/Resin-CVI matrix carbon-carbon composite (Bendix). Extensive testing was undertaken on the Dunlop composites to asses the effects of composite architecture, fibre orientation and heat treatment temperatures on friction and wear. Other friction and wear tests, conducted on the base Dunlop composite, were used to investigate the relative influences of temperature and sliding speed. It was found that the effect of temperature was dominant over composite architecture, fibre orientation and sliding speed in governing the friction and wear performance of the Dunlop composites. The development of bulk temperatures in excess of 110 C by frictional heating resulted in smooth friction and a low wear rate. Reducing heat treatment temperature also reduced the thermal conductivity producing high interface temperatures, low smooth friction coefficients and low wear rates under low energy braking conditions. However, this was at the expense of high oxidative wear rates under higher energy braking conditions. The Bendix composites had lower thermal conductivities than the fully heat treated Dunlop composite and exhibited similar friction and wear behaviour to Dunlop composites heat treated to lower temperatures. Examination of the wear surfaces using OM and SEM revealed particulate or Type I surface debris on wear surfaces tested under low energy conditions. Type I debris was stable on the wear surfaces to a temperature of 110C, after which it was gradually converted to film material or Type II surface debris by the action of heat and shear. Type I debris was associated with high erratic friction coefficients (ja.=0.55- 0.65) and high wear rates (~ 8 mg/min), whereas. Type II debris was associated low smooth friction (|LI=0.35-0.45) and low wear rates (~ 4 mg/min). Analysis of the wear debris produced from testing on large dynamometers under the simulated conditions of taxiing and landing indicated that the structure of the wear debris became highly disordered as a result of the wear process. However, evidence from XRD, TGA and DGS suggested that, under very high energy conditions, such as those encountered in a rejected take off (RTO), the wear debris was partially regraphitised at the wear face by the action of heat and shear. The results from analysis of the wear surfaces and the wear debris supported the theory that a regenerative process or friction film formation, delamination and repair operated on the wear surfaces of these brake materials.

Turbomachinery Clearance Control

NASA Technical Reports Server (NTRS)

Chupp, Raymond E.; Hendricks, Robert C.; Lattime, Scott B.; Steinetz, Bruce M.; Aksit, Mahmut F.

2007-01-01

Controlling interface clearances is the most cost effective method of enhancing turbomachinery performance. Seals control turbomachinery leakages, coolant flows and contribute to overall system rotordynamic stability. In many instances, sealing interfaces and coatings are sacrificial, like lubricants, giving up their integrity for the benefit of the component. They are subjected to abrasion, erosion, oxidation, incursive rubs, foreign object damage (FOD) and deposits as well as extremes in thermal, mechanical, aerodynamic and impact loadings. Tribological pairing of materials control how well and how long these interfaces will be effective in controlling flow. A variety of seal types and materials are required to satisfy turbomachinery sealing demands. These seals must be properly designed to maintain the interface clearances. In some cases, this will mean machining adjacent surfaces, yet in many other applications, coatings are employed for optimum performance. Many seals are coating composites fabricated on superstructures or substrates that are coated with sacrificial materials which can be refurbished either in situ or by removal, stripping, recoating and replacing until substrate life is exceeded. For blade and knife tip sealing an important class of materials known as abradables permit blade or knife rubbing without significant damage or wear to the rotating element while maintaining an effective sealing interface. Most such tip interfaces are passive, yet some, as for the high-pressure turbine (HPT) case or shroud, are actively controlled. This work presents an overview of turbomachinery sealing. Areas covered include: characteristics of gas and steam turbine sealing applications and environments, benefits of sealing, types of standard static and dynamics seals, advanced seal designs, as well as life and limitations issues.

Longitudinal changes in Langerhans cell density of the cornea and conjunctiva in contact lens-induced dry eye.

PubMed

Alzahrani, Yahya; Colorado, Luisa H; Pritchard, Nicola; Efron, Nathan

2017-01-01

The aim was to determine longitudinal changes in Langerhans cell density (LCD) in the human cornea and conjunctiva during asymptomatic and symptomatic contact lens wear. Twenty-five participants with contact lens-induced dry eye (CLIDE) and 35 without CLIDE (NO-CLIDE), diagnosed using a range of symptom questionnaires and objective tests (tear film break up, cotton thread tear test and corneal staining) were enrolled. The central cornea and nasal bulbar conjunctiva were examined using a Heidelberg laser scanning confocal microscope at baseline and following one, four and 24 weeks wear of daily disposable hydrogel contact lenses. Twenty-three non-contact lens-wearing controls were also examined. Langerhans cells were counted manually from randomly selected images. In the cornea, mean and standard error of the mean LCD was greater after one week of lens wear in CLIDE (55 ± 7 cells/mm 2 ) versus NO-CLIDE (43 ± 4 cells/mm 2 ) (p = 0.041) and controls (27 ± 4 cells/mm 2 ) (p < 0.001). LCD was also greater in NO-CLIDE versus controls (p = 0.010). At week 4, LCD was greater in CLIDE (41 ± 6 cells/mm 2 ) versus controls (27 ± 4 cells/mm 2 ) (p = 0.004). There were no other significant differences between groups at weeks four or 24. In the conjunctiva, LCD was greater after one week of lens wear in CLIDE (17 ± 1 cells/mm 2 ) (p = 0.003) and NO-CLIDE (17 ± 3 cells/mm 2 ) (p = 0.001) versus controls (7 ± 1 cells/mm 2 ). There were no significant differences between groups at weeks four or 24. The initial transient increase in corneal and conjunctival LCD in CLIDE (versus NO-CLIDE) suggests an inflammatory component in the aetiology of this condition. © 2016 Optometry Australia.

Modeling the milling tool wear by using an evolutionary SVM-based model from milling runs experimental data

NASA Astrophysics Data System (ADS)

Nieto, Paulino José García; García-Gonzalo, Esperanza; Vilán, José Antonio Vilán; Robleda, Abraham Segade

2015-12-01

The main aim of this research work is to build a new practical hybrid regression model to predict the milling tool wear in a regular cut as well as entry cut and exit cut of a milling tool. The model was based on Particle Swarm Optimization (PSO) in combination with support vector machines (SVMs). This optimization mechanism involved kernel parameter setting in the SVM training procedure, which significantly influences the regression accuracy. Bearing this in mind, a PSO-SVM-based model, which is based on the statistical learning theory, was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. To accomplish the objective of this study, the experimental dataset represents experiments from runs on a milling machine under various operating conditions. In this way, data sampled by three different types of sensors (acoustic emission sensor, vibration sensor and current sensor) were acquired at several positions. A second aim is to determine the factors with the greatest bearing on the milling tool flank wear with a view to proposing milling machine's improvements. Firstly, this hybrid PSO-SVM-based regression model captures the main perception of statistical learning theory in order to obtain a good prediction of the dependence among the flank wear (output variable) and input variables (time, depth of cut, feed, etc.). Indeed, regression with optimal hyperparameters was performed and a determination coefficient of 0.95 was obtained. The agreement of this model with experimental data confirmed its good performance. Secondly, the main advantages of this PSO-SVM-based model are its capacity to produce a simple, easy-to-interpret model, its ability to estimate the contributions of the input variables, and its computational efficiency. Finally, the main conclusions of this study are exposed.

A mixed methods survey of social anxiety, anxiety, depression and wig use in alopecia

PubMed Central

Montgomery, Kerry; White, Caroline; Thompson, Andrew

2017-01-01

Objectives This study aimed to examine levels of social anxiety, anxiety and depression reported by people with alopecia as a result of a dermatological condition and associations with wig use. The study also sought to report on experiences of wearing wigs in social situations and the relationship with social confidence. Design A cross-sectional survey was sent by email to the Alopecia UK charity mailing list and advertised on social media. Participants Inclusion criteria were a diagnosis of alopecia, aged 13 or above and sufficient English to complete the survey. Exclusion criteria included experiencing hair loss as a result of chemotherapy treatment or psychological disorder. Participants (n=338) were predominantly female (97.3%), Caucasian (93.5%) and aged between 35 and 54 years (49.4%) with a diagnosis of alopecia areata (82.6%). Main outcome measures The Social Phobia Inventory measured symptoms of social anxiety, and the Hospital Anxiety and Depression Scale was used to measure symptoms of anxiety and depression. Survey questions were designed to measure the use of wigs. Open-ended questions enabled participants to comment on their experiences of wearing wigs. Results Clinically significant levels of social anxiety (47.5%), anxiety (35.5%) and depression (29%) were reported. Participants who reported worries about not wearing a wig reported significantly higher levels of depression: t(103)=3.40, p≤0.001; anxiety: t(109)=4.80, p≤0.001; and social anxiety: t(294)=3.89, p≤0.001. Wearing wigs was reported as increasing social confidence; however, the concealment it afforded was also reported as both reducing fear of negative evaluation and maintaining anxiety. Discussion Overall, 46% of participants reported that wearing a wig had a positive impact on their everyday life with negative experiences related to fears of the wig being noticed. Psychological interventions alongside wig provision would be beneficial for people living with alopecia. PMID:28473521

Quantifying the impact cosmetic make-up has on age perception and the first impression projected.

PubMed

Dayan, Steven H; Cho, Katherine; Siracusa, Mary; Gutierrez-Borst, Selika

2015-04-01

First impressions are lasting, consequential and defined as the immediate judgment made of another from zero acquaintance. Multiple studies have reported the benefits of cosmetic make-up. We set out to investigate the psychosocial and aesthetic effects of cosmetic make-up in order to better understand why women wear it. Twenty-seven women were recruited in order to examine the effects of cosmetic make-up on first impressions. The photographs of individual subjects wearing the control cosmetics, their own make-up, and no make-up were randomly assigned to three binders (A, B, and C). Three hundred evaluators participated (100 evaluators per book) and completed a 10-point First Impression Scale for each of the 27 photos in their binder. Statistical analysis of the collected data was conducted in SPSS using two-tailed t-tests to determine the statistical significance of the differences between first impressions of Own Make-up vs No Make-up, No Make-up vs Control Make-up, and Own Makeup vs Control Make-up. There was a significant difference in improvement in all pairings across all 8 categories in the First Impressions questionnaire particularly in perceived age between own make-up, no make-up, control make-up (41, 42, 38; P<0.001). Our study evaluated the first impressions, age perception, self-esteem, and the quality of life impact that cosmetic makeup has on women's appearance and confidence. Subjects wearing cosmetic make-up appeared 4 years younger than those wearing no make-up. And the control cosmetic make-up subjects on average projected a 37% better first impression than subjects wearing no make-up. We objectively quantified and qualified the benefits of applying cosmetic make-up. Make-up can reduce the perceived age, improve the first impression projected and increase the self-esteem of those who apply it.

Project ACE Activity Sets. Book II: Grades 6 and 7.

ERIC Educational Resources Information Center

Eden City Schools, NC.

The document contains eight activity sets suitable for grades 6 and 7. Topics focus on governmental, social, and educational systems in foreign countries. Each activity set contains background reading materials, resources, concepts, general objectives, and instructional objectives. Grade 6 sets are "Soviet Youth Organizations,""How…

Study of Tool Wear Mechanisms and Mathematical Modeling of Flank Wear During Machining of Ti Alloy (Ti6Al4V)

NASA Astrophysics Data System (ADS)

Chetan; Narasimhulu, A.; Ghosh, S.; Rao, P. V.

2015-07-01

Machinability of titanium is poor due to its low thermal conductivity and high chemical affinity. Lower thermal conductivity of titanium alloy is undesirable on the part of cutting tool causing extensive tool wear. The main task of this work is to predict the various wear mechanisms involved during machining of Ti alloy (Ti6Al4V) and to formulate an analytical mathematical tool wear model for the same. It has been found from various experiments that adhesive and diffusion wear are the dominating wear during machining of Ti alloy with PVD coated tungsten carbide tool. It is also clear from the experiments that the tool wear increases with the increase in cutting parameters like speed, feed and depth of cut. The wear model was validated by carrying out dry machining of Ti alloy at suitable cutting conditions. It has been found that the wear model is able to predict the flank wear suitably under gentle cutting conditions.

Endoscopic Removal of a Bullet That Migrated to the Third Ventricle Causing Hydrocephalus.

PubMed

Aydoseli, Aydın; Unal, Tugrul Cem; Aras, Yavuz; Sabanci, Pulat Akın; Altunrende, Emre; Izgi, Nail

2017-09-01

Hydrocephalus caused by an intraventricular bullet is a rare event. We report a case of endoscopic removal of an intraventricular bullet. A 66-year-old man was admitted with a gunshot wound to the head after a suicide attempt. The bullet migrated from the frontal parenchyma to the third ventricle day 4 of admission. On day 21 of admission, the patient developed hydrocephalus with obstruction of the cerebral aqueduct. The bullet was accessed through an endoscopic third ventriculostomy and removed using an endoscope. Hydrocephalus may develop in patients with intraventricular foreign objects. When such objects must be removed, the endoscopic approach is a safe, efficient, and minimally invasive procedure. To our knowledge, this is the first case in the literature of foreign object removal from the ventricle via a transcortical endoscopic approach. Copyright © 2017 Elsevier Inc. All rights reserved.

Tribological behaviour of orthodontic archwires under dry and wet sliding conditions in-vitro. II--Wear patterns.

PubMed

Berradja, Abdenacer; Willems, Guy; Celis, Jean-Pierre

2006-05-01

To evaluate the wear patterns of orthodontic archwires in dry and wet conditions in-vitro. The patterns of wear of stainless steel and NiTi orthodontic archwires were investigated with a fretting wear tribometer fitted with an alumina ball. The tribometer was operated at 23 degrees C in three different environments: ambient air with 50 per cent relative humidity (RH), 0.9 wt. per cent sodium chloride solution and deionised water. Differences in the wear characteristics of the archwires were investigated by scanning electron microscopy. Energy Dispersive X-ray Analysis and Inductively Coupled Plasma Analysis were used to investigate the surface composition of the wires, the wear debris generated during fretting and the corrosion products in the test solutions. Both archwire materials were degraded by oxidational wear in ambient air. The NiTi wires were more resistant to wear than the stainless steel wires. In the aqueous media the stainless steel wires were degraded by abrasive wear, while the NiTi wires were degraded by adhesive wear. In ambient air with 50 per cent RH, NiTi wires were more resistant to wear than stainless steel wires. Both archwire materials exhibited higher wear rates in the solutions than in air, indicating some synergism between the wear and corrosion processes. In the solutions the stainless steel archwires had a much lower corrosion-wear resistance than the NiTi archwires.

Subminiature eddy current transducers for studying boride coatings

NASA Astrophysics Data System (ADS)

Dmitriev, S. F.; Ishkov, A. V.; Malikov, V. N.; Sagalakov, A. M.

2016-07-01

Strengthening of parts and units of machines, increased reliability and longer service life is an important task of modern mechanical engineering. The main objects of study in the work were selected steel 65G and 50HGA, wear-resistant boride coatings ternary system Fe-B-Fe n B which were investigated by scanning electron microscopy and eddy-current nondestructive methods.

Brief Report: Influence of Physical Activity on Sleep Quality in Children with Autism

ERIC Educational Resources Information Center

Wachob, David; Lorenzi, David G.

2015-01-01

Sleep-related problems are often documented in children with Autism Spectrum Disorders (ASD). This study examined physical activity as a variable that might influence sleep quality in children with ASD. Ten children, ages 9-16 years, were asked to wear accelerometer devices for 7 days in order to track objective measures of activity and sleep…

Risk factors for complications associated with upper gastrointestinal foreign bodies

PubMed Central

Hong, Kyong Hee; Kim, Yoon Jae; Kim, Jae Hak; Chun, Song Wook; Kim, Hee Man; Cho, Jae Hee

2015-01-01

AIM: To investigate predictive risk factors associated with complications in the endoscopic removal of foreign bodies from the upper gastrointestinal tract. METHODS: We retrospectively reviewed the medical records of 194 patients with a diagnosis of foreign body impaction in the upper gastrointestinal tract, confirmed by endoscopy, at two university hospital in South Korea. Patient demographic data, including age, gender, intention to ingestion, symptoms at admission, and comorbidities, were collected. Clinical features of the foreign bodies, such as type, size, sharpness of edges, number, and location, were analyzed. Endoscopic data those were analyzed included duration of foreign body impaction, duration of endoscopic performance, endoscopic device, days of hospitalization, complication rate, 30-d mortality rate, and the number of operations related to foreign body removal. RESULTS: The types of upper gastrointestinal foreign bodies included fish bones, drugs, shells, meat, metal, and animal bones. The locations of impacted foreign bodies were the upper esophagus (57.2%), mid esophagus (28.4%), stomach (10.8%), and lower esophagus (3.6%). The median size of the foreign bodies was 26.2 ± 16.7 mm. Among 194 patients, endoscopic removal was achieved in 189, and complications developed in 51 patients (26.9%). Significant complications associated with foreign body impaction and removal included deep lacerations with minor bleeding (n = 31, 16%), ulcer (n = 11, 5.7%), perforation (n = 3, 1.5%), and abscess (n = 1, 0.5%). Four patients underwent operations because of incomplete endoscopic foreign body extraction. In multivariate analyses, risk factors for endoscopic complications and failure were sharpness (HR = 2.48, 95%CI: 1.07-5.72; P = 0.034) and a greater than 12-h duration of impaction (HR = 2.42, 95%CI: 1.12-5.25, P = 0.025). CONCLUSION: In cases of longer than 12 h since foreign body ingestion or sharp-pointed objects, rapid endoscopic intervention should be provided in patients with ingested foreign bodies. PMID:26185385

Study of sleeping in a chemical protective ensemble in a warfare environment. Final report 26 Aug 81-2 Dec 82

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cacioppo, G.M.; Annis, J.F.

1982-12-01

Experiments were performed to evaluate the quality of sleep experienced by individuals wearing different chemical protective ensembles (CPE). A series of seven experiments were conducted in which two test subjects slept overnight in an environmentally controlled room while wearing either pajamas (control ensemble) or one of three different CPEs. The three CPEs tested were: the standard West German ground crew ensemble, an ensemble comprised of a combination of equipment of which the Canadian chemical protective coverall was the principal item of clothing, and the U.S. Army standard ground crew ensemble Body temperatures, sleep records, and other physiological measurements were monitoredmore » overnight and form the basis of the objective evaluation. Subjective data were collected by an experiment monitor who kept the test participants under constant observation. Additionally, the participants were required to complete a standard debriefing questionnaire form each post-experiment morning. Because of the limited scope of the experiment, statistical analysis was not appropriate. However, both the objective and subjective data reflected consistent trends and allow confidence in the assessment that current U.S. and NATO CPE combinations provide for adequate sleep quality.« less

Acculturation and Sun-Safe Behaviors Among US Latinos: Findings From the 2005 Health Information National Trends Survey

PubMed Central

Unger, Jennifer B.; Yaroch, Amy L.; Cockburn, Myles G.; Baezconde-Garbanati, Lourdes; Reynolds, Kim D.

2009-01-01

Objectives. We examined the relationship between acculturation and sun safety among US Latinos. Methods. We used linear regression models to analyze data from 496 Latino respondents to the 2005 Health Information National Trends Survey. Using sunscreen, seeking shade, and wearing protective clothing were the primary outcomes and were assessed by frequency scales. Acculturation was assessed with a composite index. Results. In bivariate models, acculturation was negatively associated with use of shade and protective clothing and positively associated with sunscreen use (all, P < .004). In adjusted models, acculturation was negatively associated with seeking shade and wearing protective clothing across gender and region of residence (all, P < .05). Conclusions. Our results demonstrated both adverse and beneficial effects of acculturation on Latinos’ risk behaviors relating to skin cancer. Education about sun safety is needed for all Latinos and should be tailored to different levels of acculturation. Initiatives for Latinos who are not yet acculturated could focus on reinforcing existing sun-safe behaviors and presenting new ones, such as use of sunscreen; initiatives for highly acculturated Latinos might require more resources because the objective is behavior modification. PMID:19150918

NASA's Hall Thruster Program

NASA Technical Reports Server (NTRS)

Jankovsky, Robert S.; Jacobson, David T.; Rawlin, Vincent K.; Mason, Lee S.; Mantenieks, Maris A.; Manzella, David H.; Hofer, Richard R.; Peterson, Peter Y.

2001-01-01

NASA's Hall thruster program has base research and focused development efforts in support of the Advanced Space Transportation Program, Space-Based Program, and various other programs. The objective of the base research is to gain an improved understanding of the physical processes and engineering constraints of Hall thrusters to enable development of advanced Hall thruster designs. Specific technical questions that are current priorities of the base effort are: (1) How does thruster life vary with operating point? (2) How can thruster lifetime and wear rate be most efficiently evaluated? (3) What are the practical limitations for discharge voltage as it pertains to high specific impulse operation (high discharge voltage) and high thrust operation (low discharge voltage)? (4) What are the practical limits for extending Hall thrusters to very high input powers? and (5) What can be done during thruster design to reduce cost and integration concerns? The objective of the focused development effort is to develop a 50 kW-class Hall propulsion system, with a milestone of a 50 kW engineering model thruster/system by the end of program year 2006. Specific program wear 2001 efforts, along with the corporate and academic participation, are described.

Analysis of the United States Navy Foreign Area Officer Program

DTIC Science & Technology

2013-03-01

Century Defense, the present objectives may shape the climate of the community, as they will have global presence emphasizing the Asia-Pacific and...fortify the Navy’s corps of foreign specialists. The findings of this thesis will be important to formulating the necessary changes in current and...investigate an area that was relatively new to the Navy and discover where changes can be made. This community relies on nontechnical expertise and is

Tibial interface wear in retrieved total knee components and correlations with modular insert motion.

PubMed

Rao, Anand R; Engh, Gerard A; Collier, Matthew B; Lounici, Smain

2002-10-01

Wear occurring at the interface between the polyethylene insert and metal baseplate of a modular tibial component has become an increasingly common finding at the time of revision total knee arthroplasty. Although this so-called backside wear on retrieved polyethylene inserts has been evaluated in prior studies, wear on retrieved metal baseplates has not been described, to our knowledge. The purposes of the present study were to characterize backside wear on retrieved polyethylene inserts and on the mating surfaces of their corresponding baseplates and to investigate if there is a relationship between backside wear and relative motion of the modular elements. Twenty-nine retrieved modular tibial components of twelve fixed-bearing designs were analyzed in vitro with regard to backside wear and relative motion between the polyethylene insert and the metal baseplate. We graded the backside of each polyethylene insert and the mating surface of the metal baseplate for wear with use of a scoring system that consisted of three modes of wear and three levels of severity of wear. Relative motion between the insert and the baseplate was measured in the transverse plane with use of a mechanical testing machine. These measurements were used to compute the insert motion index, which served to quantify unrestricted motion of the insert with respect to the baseplate. The mean insert motion index for the tibial components was 416 micro m (range, 104 micro m to 760 micro m). On a wear-grading scale ranging from 0 to 54 (with 0 indicating no wear), the mean backside wear score was 30 (range, 12 to 48) for the inserts and 28 (range, 7 to 51) for the baseplates. Insert motion was positively correlated with backside polyethylene wear (p = 0.003) and baseplate wear (p < 0.001). Baseplate wear was strongly correlated with backside polyethylene wear (p < 0.001). Backside wear was correlated with the relative motion between the polyethylene insert and the metal baseplate. New locking mechanism designs directed toward better methods of securing the polyethylene insert to the tibial tray are needed to minimize the generation of particulate wear debris at the modular interface.

Tribological Behavior of Mg97Zn1Y2 Alloy at Elevated Temperatures of 50-200 °C

NASA Astrophysics Data System (ADS)

An, J.; Feng, J. H.; Yan, X. H.; Li, R. G.

2017-10-01

The tribological behavior of Mg97Zn1Y2 alloy was investigated using a pin-on-disk wear machine at wear temperatures of 50-200 °C. Morphologies and chemical compositions of worn surfaces were analyzed using scanning electron microscope and energy-dispersive x-ray spectrometer. The microstructural evolution and hardness change in subsurfaces were examined by optical microscopy and hardness tester. The results showed that the wear temperature had significant influence on the coefficient of friction and wear rate. At wear temperatures of 50-200 °C, with increasing applied load, the coefficient of friction went down rapidly then turned to decrease slowly in the mild wear regime, and continuously decreased modestly until the largest applied load in the severe wear regime. Increasing wear temperature from 50 to 200 °C decreased the mild to severe wear transition load linearly from 120 to 60 N. In the mild wear regime, the main wear mechanisms were identified as abrasion + oxidation and delamination + surface oxidation at 50-150 °C, and delamination at 200 °C, while in the severe wear regime, the main wear mechanisms were identified as severe plastic deformation + spallation of oxide layer and surface melting at 50-150 °C, and severe plastic deformation and surface melting at 200 °C. The microstructural transformation from the deformed to the dynamically recrystallized (DRX), and hardness change from the strain hardening to softening were found in the subsurfaces before and after mild to severe transition. The DRX softening mechanism was determined for mild to severe wear transition at 50-200 °C. A wear transition map was constructed for Mg97Zn1Y2 alloy on applied load versus wear temperature.

Foreign-body ingestion: characteristics and outcomes in a lower socioeconomic population with predominantly intentional ingestion.

PubMed

Palta, Renee; Sahota, Amandeep; Bemarki, Ali; Salama, Paul; Simpson, Nicole; Laine, Loren

2009-03-01

Previous reports of foreign-body ingestions focused primarily on accidental ingestions. To describe the characteristics and management of foreign-body ingestions, with predominantly intentional ingestion, in a lower socioeconomic status population. A retrospective case series. An urban county hospital. Patients >/=17 years old, with foreign-body ingestions between 2000 and 2006. Characteristics of ingestion cases, endoscopic extraction, need for surgery, and complications. Among 262 cases, 92% were intentional, 85% involved psychiatric patients, and 84% occurred in patients with prior ingestions. The time from ingestion to presentation was >48 hours in 168 cases (64%). The overall success rate for endoscopic extraction was 90% (165/183 cases). Surgery was performed in 30 cases (11%) and was more common for objects beyond the pylorus versus objects above the pylorus (16/43 [37%] vs 10/151 [7%], respectively) and in cases with a greater delay from ingestion to presentation (25/168 [15%] if >48 hours vs 4/77 [5%] if 48 hours vs 14/165 [8%] if

The Wear Behavior of HVOF Sprayed Near-Nanostructured WC-17%Ni(80/20)Cr Coatings in Dry and Slurry Wear Conditions

NASA Astrophysics Data System (ADS)

Ben Mahmud, Tarek A.; Atieh, Anas M.; Khan, Tahir I.

2017-07-01

The ability to deposit nanostructured feedstock by using high-velocity oxygen-fuel (HVOF) spray offers potential improvements in coating hardness, wear resistance and toughness for applications in the oil sands industry. In this study, the wear behavior of a near-nanostructured coating was compared under dry and slurry abrasive wear test using an uncoated AISI-1018 low-carbon steel substrate as a reference. The coating microstructures were analyzed in the as-sprayed, dry and slurry test conditions using scanning electron microscopy, x-ray diffraction and microhardness measurements. Wear behavior of the steel and coating surfaces were assessed using a pin-on-plate wear test under various loads. The results showed that a coating could be successfully deposited using the HVOF spraying technique and with retention of the near-nanosized WC dispersion within the coating structure. The wear rate under dry test conditions was greater for the steel and coating compared to tests performed under slurry conditions. Examination of the wear tracks revealed that the wear mechanism was different for the two test conditions. Wear in the dry test condition resulted from 2-body abrasion, while 3-body abrasion dominated wear in slurry conditions. The latter showed lower wear rates due to a lubricating effect of the oil.

Wear-Induced Changes in FSW Tool Pin Profile: Effect of Process Parameters

NASA Astrophysics Data System (ADS)

Sahlot, Pankaj; Jha, Kaushal; Dey, G. K.; Arora, Amit

2018-06-01

Friction stir welding (FSW) of high melting point metallic (HMPM) materials has limited application due to tool wear and relatively short tool life. Tool wear changes the profile of the tool pin and adversely affects weld properties. A quantitative understanding of tool wear and tool pin profile is crucial to develop the process for joining of HMPM materials. Here we present a quantitative wear study of H13 steel tool pin profile for FSW of CuCrZr alloy. The tool pin profile is analyzed at multiple traverse distances for welding with various tool rotational and traverse speeds. The results indicate that measured wear depth is small near the pin root and significantly increases towards the tip. Near the pin tip, wear depth increases with increase in tool rotational speed. However, change in wear depth near the pin root is minimal. Wear depth also increases with decrease in tool traverse speeds. Tool pin wear from the bottom results in pin length reduction, which is greater for higher tool rotational speeds, and longer traverse distances. The pin profile changes due to wear and result in root defect for long traverse distance. This quantitative understanding of tool wear would be helpful to estimate tool wear, optimize process parameters, and tool pin shape during FSW of HMPM materials.

Injury Risk Assessment of Extravehicular Mobility Unit (EMU) Phase VI and Series 4000 Gloves During Extravehicular Activity (EVA) Hand Manipulation Tasks

NASA Technical Reports Server (NTRS)

Kilby, Melissa

2015-01-01

Functional Extravehicular Mobility Units (EMUs) with high precision gloves are essential for the success of Extravehicular Activity (EVA). Previous research done at NASA has shown that total strength capabilities and performance are reduced when wearing a pressurized EMU. The goal of this project was to characterize the human-space suit glove interaction and assess the risk of injury during common EVA hand manipulation tasks, including pushing, pinching and gripping objects. A custom third generation sensor garment was designed to incorporate a combination of sensors, including force sensitive resistors, strain gauge sensors, and shear force sensors. The combination of sensors was used to measure the forces acting on the finger nails, finger pads, finger tips, as well as the knuckle joints. In addition to measuring the forces, data was collected on the temperature, humidity, skin conductance, and blood perfusion of the hands. Testing compared both the Phase VI and Series 4000 glove against an ungloved condition. The ungloved test was performed wearing the sensor garment only. The project outcomes identified critical landmarks that experienced higher workloads and are more likely to suffer injuries. These critical landmarks varied as a function of space suit glove and task performed. The results showed that less forces were acting on the hands while wearing the Phase VI glove as compared to wearing the Series 4000 glove. Based on our findings, the engineering division can utilize these methods for optimizing the current space suit glove and designing next generation gloves to prevent injuries and optimize hand mobility and comfort.

Tribocorrosion behavior of biofunctional titanium oxide films produced by micro-arc oxidation: Synergism and mechanisms.

PubMed

Marques, Isabella da Silva Vieira; Alfaro, Maria Fernanda; Cruz, Nilson Cristino da; Mesquita, Marcelo Ferraz; Takoudis, Christos; Sukotjo, Cortino; Mathew, Mathew T; Barão, Valentim Adelino Ricardo

2016-07-01

Dental implants, inserted into the oral cavity, are subjected to a synergistic interaction of wear and corrosion (tribocorrosion), which may lead to implant failures. The objective of this study was to investigate the tribocorrosion behavior of Ti oxide films produced by micro-arc oxidation (MAO) under oral environment simulation. MAO was conducted under different conditions as electrolyte composition: Ca/P (0.3M/0.02M or 0.1M/0.03M) incorporated with/without Ag (0.62g/L) or Si (0.04M); and treatment duration (5 and 10min). Non-coated and sandblasted samples were used as controls. The surfaces morphology, topography and chemical composition were assessed to understand surface properties. ANOVA and Tukey׳s HSD tests were used (α=0.05). Biofunctional porous oxide layers were obtained. Higher Ca/P produced larger porous and harder coatings when compared to non-coated group (p<0.001), due to the presence of rutile crystalline structure. The total mass loss (Kwc), which includes mass loss due to wear (Kw) and that due to corrosion (Kc) were determined. The dominant wear regime was found for higher Ca/P groups (Kc/Kw≈0.05) and a mechanism of wear-corrosion for controls and lower Ca/P groups (Kc/Kw≈0.11). The group treated for 10min and enriched with Ag presented the lowest Kwc (p<0.05). Overall, MAO process was able to produce biofunctional oxide films with improved surface features, working as tribocorrosion resistant surfaces. Copyright © 2015 Elsevier Ltd. All rights reserved.

Automation of wear analysis for large caliber weapons

NASA Astrophysics Data System (ADS)

Salafia, Dominick; DeLeon, Norberto L.; Outlaw, James F.

1999-12-01

As part of the Test and Evaluation Command (TECOM) the Metrology and Simulation Division (MT-MS) at the U.S. Army Yuma Proving Ground (USAYPG) has the mission to measure and record the wear effects of conventional and experimental munitions on large caliber weapons. The primary objective is to ensure that the weapon to be fired will safely meet the mission requirements for the quantity and energy of the munitions under live fire testing. Currently, there are two criteria used to "deadline" a weapon. One is the actual physical wear tolerance. The other relates to the energy (zone) expended by the round and the subsequent fatigue induced in the microstructure of the gun tube. The latter is referred to as the Equivalent Full Charge (EFC) for the particular round. In order to maximize safety and reduce the time required to manually search records for the appropriate level of useful life, the Measurements and Simulation Branch of MT-MS at USAYPG has made use of the installation network such that critical information may be accessed from the local area network or the Internet. An electronic database has been constructed and the query routines have been written so that systems test personnel, test directors (TD), and other government organizations may conduct a search for a particular weapon. The user may enter specifications such as percent physical life, percent EFC life, caliber, model, modifications, and serial number or any combination thereof. This paper is intended to inform the engineering and scientific community, engaged in weapons performance evaluation using simulations and field testing, of the existence of wear analysis automation for large caliber weapons.

The interactions between attrition, abrasion and erosion in tooth wear.

PubMed

Shellis, R Peter; Addy, Martin

2014-01-01

Tooth wear is the result of three processes: abrasion (wear produced by interaction between teeth and other materials), attrition (wear through tooth-tooth contact) and erosion (dissolution of hard tissue by acidic substances). A further process (abfraction) might potentiate wear by abrasion and/or erosion. Knowledge of these tooth wear processes and their interactions is reviewed. Both clinical and experimental observations show that individual wear mechanisms rarely act alone but interact with each other. The most important interaction is the potentiation of abrasion by erosive damage to the dental hard tissues. This interaction seems to be the major factor in occlusal and cervical wear. The available evidence is insufficient to establish whether abfraction is an important contributor to tooth wear in vivo. Saliva can modulate erosive/abrasive tooth wear, especially through formation of pellicle, but cannot prevent it. © 2014 S. Karger AG, Basel.

Simulation of wear in overhead current collection systems

NASA Astrophysics Data System (ADS)

Klapas, D.; Benson, F. A.; Hackam, R.

1985-09-01

Apparatus have been designed to simulate the wear from conductors in a railway current collection system. The main features of the wear machine include a continuous monitoring of the strip wear, strip traversing, and dwell-time test facilities for the investigation of oxidational wear on a copper disk, simulating the contact wire. Disk wear is measured in situ by the spherical indentations method. Typical results of the specific wear rate are also presented to demonstrate the capability of the apparatus.

A new methodology for predictive tool wear

NASA Astrophysics Data System (ADS)

Kim, Won-Sik

An empirical approach to tool wear, which requires a series of machining tests for each combination of insert and work material, has been a standard practice for industries since early part of the twentieth century. With many varieties of inserts and work materials available for machining, the empirical approach is too experiment-intensive that the demand for the development of a model-based approach is increasing. With a model-based approach, the developed wear equation can be extended without additional machining experiments. The main idea is that the temperatures on the primary wear areas are increasing such that the physical properties of the tool material degrade substantially and consequently tool wear increases. Dissolution and abrasion are identified to be the main mechanisms for tool wear. Flank wear is predominantly a phenomenon of abrasion as evident by the presence of a scoring mark on the flank surface. Based on this statement, it is reasonable to expect that the flank-wear rate would increase with the content of hard inclusions. However, experimental flank wear results did not necessary correspond to the content of cementite phase present in the steels. Hence, other phenomena are believed to significantly affect wear behavior under certain conditions. When the cutting temperature in the flank interface is subjected to high enough temperatures, pearlitic structure austenizes. During the formation of a new austenitic phase, the existing carbon is dissolved into the ferrite matrix, which will reduce the abrasive action. To verify the austenitic transformation, turning tests were conducted with plain carbon steels. The machined surface areas are imaged using X-ray diffraction the Scanning Electron Microscope (SEM) and the Transmission Electron Microscope (TEM). On the other hand, crater wear occurs as a result of dissolution wear and abrasive wear. To verify the wear mechanisms of crater wear, various coating inserts as well as uncoated inserts were turned with various cutting conditions and the results were compared with the proposed analytical wear models. The crater surfaces after machining have been carefully studied to shed light on the physics behind the crater wear. In addition, the abrasive wear mechanism plays a major role in the development of crater wear. Laser shock processing (LSP) has been applied to locally relieve the deleterious tensile residual stresses on the crater surface of a coated tool, thus to improve the hardness of the coating. This thesis shows that LSP has indeed improve wear resistance of CVD coated alumina tool inserts, which has residual stress due to high processing temperature. LSP utilizes a very short laser pulse with high energy density, which induces high-pressure stress wave propagation. The residual stresses are relieved by incident shock waves on the coating surface. Residual stress levels of LSP CVD alumina-coated carbide insert were evaluated by the X-ray diffractometer. Based on these results, LSP parameters such as number of laser pulses and laser energy density can be controlled to reduce residual stress. Crater wear shows that the wear resistance increase with LSP treated tool inserts. Because the hardness data are used to predict the wear, the improvement in hardness and wear resistance shows that the mechanism of crater wear also involves abrasive wear.

Effects of working gas pressure on zirconium dioxide thin film prepared by pulsed plasma deposition: roughness, wettability, friction and wear characteristics.

PubMed

Berni, M; Marchiori, G; Gambardella, A; Boi, M; Bianchi, M; Russo, A; Visani, A; Marcacci, M; Pavan, P G; Lopomo, N F

2017-08-01

In joint arthroplasty one of the main issues related to the failure of prosthetic implants is due to the wear of the ultra-high molecular weight polyethylene (UHMWPE) component. Surface treatments and coatings have been recognized as enhancing methods, able to improve the tribological properties of the implants. Therefore, the main objective of this work was to investigate the possibility to fabricate yttria-stabilized zirconia (YSZ) coatings on a metal (AISI 316-L) substrate by means of Pulsed Electron Deposition, in order to improve the tribological behavior of the polymer-metal coupling, by reducing the initial wear of the UHMWPE component. In order to optimize the coating characteristics, the effects of working gas pressure on both its morphological and tribological properties were analyzed. Morphological characterization of the films was evaluated by Atomic Force Microscopy (AFM). Coating wettability was also estimated by contact angle (CA) measurement. Tribological performance (coupling friction and wear of UHMWPE) was evaluated by using a ball-on-disc tribometer during highly-stressing tests in dry and lubricated (i.e. NaCl and serum) conditions; friction and wear were specifically evaluated at the initial sliding distances - to highlight the main effect of coating morphology - and after 100m - where the influence of the intrinsic materials properties prevails. AFM analysis highlighted that the working pressure heavily affected the morphological characteristics of the realized films. The wettability of the coating at the highest and lowest deposition pressures (CA ~ 60°, closed to substrate value) decreased for intermediate pressures, reaching a maximum CA of ~ 90°. Regarding tribological tests, a strong correlation was found in the initial steps between friction coefficient and wettability, which decreased as the distance increased. Concerning UHMWPE wear associated to coated counterpart, at 100m a reduction rate of about 7% in dry, 12% in NaCl and 5% in presence of serum was obtained compared to the uncoated counterpart. Differently from what highlighted for friction, no correlation was found between wear rate and morphological parameters. These findings, in agreement with literature, underlined the effect of the deposition pressure on the morphological properties, but suggested that physical characteristics are influenced too. Further research on the deposition process will be required in order to improve the tribological performance of the coating at long distances, addressing - above all - orthopedic applications. Copyright © 2017 Elsevier Ltd. All rights reserved.

Elucidation of wear mechanisms by ferrographic analysis

NASA Technical Reports Server (NTRS)

Jones, W. R., Jr.

1981-01-01

The use of ferrographic analysis in conjunction with light and scanning electron microscopy is described for the elucidation of wear mechanisms taking place in operating equipment. Example of adhesive wear, abrasive wear, corrosive wear, rolling element fatigue, lubricant breakdown, and other wear modes are illustrated. In addition, the use of magnetic solutions to precipitate nonmagnetic debris from aqueous and nonaqueous fluids is described.

The Latino Paradox in Neighborhood Context: The Case of Asthma and Other Respiratory Conditions

PubMed Central

Cagney, Kathleen A.; Browning, Christopher R.; Wallace, Danielle M.

2007-01-01

Objectives. Evidence indicates that foreign-born Latinos have a health advantage compared with US-born persons of the same socioeconomic status. An explanation for this paradox has remained elusive. We examined the extent to which this paradox exists for the prevalence of asthma and other respiratory conditions. We then explored the role of neighborhood social context in understanding any observed advantage. We invoked theories of social organization, collective efficacy, and the urban ethnic enclave. Methods. We combined data from the Project on Human Development in Chicago Neighborhoods Community Survey with 2 other data sources and used hierarchical generalized linear modeling techniques. Results. We found a distinctly graded effect for asthma and other breathing problems among foreign-born Latinos, depending on community composition. Foreign-born Latinos embedded in a neighborhood that had a high percentage of foreign-born residents experienced a significantly lower prevalence of asthma and other breathing problems; those in communities that had a low percentage of foreign-born residents had the highest prevalence overall (even when compared with African Americans). Conclusions. Foreign-born Latinos have a respiratory health advantage only in enclave-like settings. Contexts such as these may provide the cohesiveness critical for effective prevention. PMID:17395846