DOE Office of Scientific and Technical Information (OSTI.GOV)

Cozzi, A.; Crawford, C.; Fox, K.

More than 56 million gallons of radioactive and hazardous waste are stored in 177 underground storage tanks at the U.S. Department of Energy’s (DOE’s) Hanford Site in Washington State. The HLW will be vitrified in the HLW facility for ultimate disposal at an offsite federal repository. A portion (~35%) of the LAW will be vitrified in the LAW vitrification facility for disposal onsite at the Integrated Disposal Facility (IDF). The pretreatment and HLW vitrification facilities will have the capacity to treat and immobilize all of the wastes destined for those facilities. However, a second facility will be needed for themore » expected volume of LAW requiring immobilization. Cast Stone, a cementitious waste form, is being considered to provide the required additional LAW immobilization capacity. The Cast Stone waste form must be acceptable for disposal in the IDF. The Cast Stone waste form and immobilization process must be tested to demonstrate that the final Cast Stone waste form can comply with the waste acceptance criteria for the disposal facility and that the immobilization processes can be controlled to consistently provide an acceptable waste form product. A testing program was developed in fiscal year (FY) 2012 describing in detail the work needed to develop and qualify Cast Stone as a waste form for the solidification of Hanford LAW. A statistically designed test matrix was used to evaluate the effects of key parameters on the properties of the Cast Stone as it is initially prepared and after curing. For the processing properties, the water-to-dry-blend mix ratio was the most significant parameter in affecting the range of values observed for each property. The single shell tank (SST) Blend simulant also showed differences in measured properties compared to the other three simulants tested. A review of the testing matrix and results indicated that an additional set of tests would be beneficial to improve the understanding of the impacts noted in the Screening Matrix tests. A set of Cast Stone formulations were devised to augment the original screening test matrix and focus on the range of the test conditions. Fly ash and blast furnace slag were limited to either northwest or southeast and the salt solutions were narrowed to the Average and the SST Blend at the 7.8M Na concentration. To fill in the matrix, a mix ratio of 0.5 was added. In addition, two admixtures, Xypex Admix C-500 and Rheomac SF100 (silica fume), were added as an additional dry material binder in select compositions. As in the Screening Matrix, both fresh and cured properties were evaluated for the formulations. In this study, properties that were influenced by the W/DM ratio in the Screening Matrix; flow diameter, plastic viscosity, density, and compressive strength, showed consistent behavior with respect to W/DM. The leach index for highly soluble components, sodium and nitrate, were not influenced by changes in formulation or the admixtures. The leach index for both iodine and Tc-99 show an influence from the addition of the admixture, Xypex Admix C-500. Additional testing should be performed to further evaluate the influence of Xypex Admix C-500 on the leach index over a range of admixture concentrations, Cast Stone formulations, and curing and storage conditions.« less

Cast Stone Oxidation Front Evaluation: Preliminary Results For Samples Exposed To Moist Air

DOE Office of Scientific and Technical Information (OSTI.GOV)

Langton, C. A.; Almond, P. M.

The rate of oxidation is important to the long-term performance of reducing salt waste forms because the solubility of some contaminants, e.g., technetium, is a function of oxidation state. TcO{sub 4}{sup -} in the salt solution is reduced to Tc(IV) and has been shown to react with ingredients in the waste form to precipitate low solubility sulfide and/or oxide phases. Upon exposure to oxygen, the compounds containing Tc(IV) oxidize to the pertechnetate ion, Tc(VII)O{sub 4}{sup -}, which is very soluble. Consequently the rate of technetium oxidation front advancement into a monolith and the technetium leaching profile as a function ofmore » depth from an exposed surface are important to waste form performance and ground water concentration predictions. An approach for measuring contaminant oxidation rate (effective contaminant specific oxidation rate) based on leaching of select contaminants of concern is described in this report. In addition, the relationship between reduction capacity and contaminant oxidation is addressed. Chromate (Cr(VI) was used as a non-radioactive surrogate for pertechnetate, Tc(VII), in Cast Stone samples prepared with 5 M Simulant. Cast Stone spiked with pertechnetate was also prepared and tested. Depth discrete subsamples spiked with Cr were cut from Cast Stone exposed to Savannah River Site (SRS) outdoor ambient temperature fluctuations and moist air. Depth discrete subsamples spiked with Tc-99 were cut from Cast Stone exposed to laboratory ambient temperature fluctuations and moist air. Similar conditions are expected to be encountered in the Cast Stone curing container. The leachability of Cr and Tc-99 and the reduction capacities, measured by the Angus-Glasser method, were determined for each subsample as a function of depth from the exposed surface. The results obtained to date were focused on continued method development and are preliminary and apply to the sample composition and curing / exposure conditions described in this report. The Cr oxidation front (depth to which soluble Cr was detected) for the Cast Stone sample exposed for 68 days to ambient outdoor temperatures and humid air (total age of sample was 131 days) was determined to be about 35 mm below the top sample surface exposed. The Tc oxidation front, depth at which Tc was insoluble, was not determined. Interpretation of the results indicates that the oxidation front is at least 38 mm below the exposed surface. The sample used for this measurement was exposed to ambient laboratory conditions and humid air for 50 days. The total age of the sample was 98 days. Technetium appears to be more easily oxidized than Cr in the Cast Stone matrix. The oxidized forms of Tc and Cr are soluble and therefore leachable. Longer exposure times are required for both the Cr and Tc spiked samples to better interpret the rate of oxidation. Tc spiked subsamples need to be taken further from the exposed surface to better define and interpret the leachable Tc profile. Finally Tc(VII) reduction to Tc(IV) appears to occur relatively fast. Results demonstrated that about 95 percent of the Tc(VII) was reduced to Tc(IV) during the setting and very early stage setting for a Cast Stone sample cured 10 days. Additional testing at longer curing times is required to determine whether additional time is required to reduce 100 % of the Tc(VII) in Cast Stone or whether the Tc loading exceeded the ability of the waste form to reduce 100 % of the Tc(VII). Additional testing is required for samples cured for longer times. Depth discrete subsampling in a nitrogen glove box is also required to determine whether the 5 percent Tc extracted from the subsamples was the result of the sampling process which took place in air. Reduction capacity measurements (per the Angus-Glasser method) performed on depth discrete samples could not be correlated with the amount of chromium or technetium leached from the depth discrete subsamples or with the oxidation front inferred from soluble chromium and technetium (i.e., effective Cr and Tc oxidation fronts). Residual reduction capacity in the oxidized region of the test samples indicates that the remaining reduction capacity is not effective in re-reducing Cr(VI) or Tc(VII) in the presence of oxygen. Depth discrete sampling and leaching is a useful for evaluating Cast Stone and other chemically reducing waste forms containing ground granulated blast furnace slag (GGBFS) or other reduction / sequestration reagents to control redox sensitive contaminant chemistry and leachability in the near surface disposal environment. Based on results presented in this report, reduction capacity measured by the Angus-Glasser Ce(IV) method is not an appropriate or meaningful parameter for determining or predicting Tc and Cr oxidation / retentions, speciation, or solubilities in cementitious materials such as Cast Stone. A model for predicting Tc(IV) oxidation to soluble Tc(VII) should consider the waste form porosity (pathway for oxygen ingress), oxygen source, and the contaminant specific oxidation rates and oxidation fronts. Depth discrete sampling of materials exposed to realistic conditions in combination with short term leaching of crushed samples has potential for advancing the understanding of factors influencing performance. This information can be used to support conceptual model development.« less

Generation and evaluation of 3D digital casts of maxillary defects based on multisource data registration: A pilot clinical study.

PubMed

Ye, Hongqiang; Ma, Qijun; Hou, Yuezhong; Li, Man; Zhou, Yongsheng

2017-12-01

Digital techniques are not clinically applied for 1-piece maxillary prostheses containing an obturator and removable partial denture retained by the remaining teeth because of the difficulty in obtaining sufficiently accurate 3-dimensional (3D) images. The purpose of this pilot clinical study was to generate 3D digital casts of maxillary defects, including the defective region and the maxillary dentition, based on multisource data registration and to evaluate their effectiveness. Twelve participants with maxillary defects were selected. The maxillofacial region was scanned with spiral computer tomography (CT), and the maxillary arch and palate were scanned using an intraoral optical scanner. The 3D images from the CT and intraoral scanner were registered and merged to form a 3D digital cast of the maxillary defect containing the anatomic structures needed for the maxillary prosthesis. This included the defect cavity, maxillary dentition, and palate. Traditional silicone impressions were also made, and stone casts were poured. The accuracy of the digital cast in comparison with that of the stone cast was evaluated by measuring the distance between 4 anatomic landmarks. Differences and consistencies were assessed using paired Student t tests and the intraclass correlation coefficient (ICC). In 3 participants, physical resin casts were produced by rapid prototyping from digital casts. Based on the resin casts, maxillary prostheses were fabricated by using conventional methods and then evaluated in the participants to assess the clinical applicability of the digital casts. Digital casts of the maxillary defects were generated and contained all the anatomic details needed for the maxillary prosthesis. Comparing the digital and stone casts, a paired Student t test indicated that differences in the linear distances between landmarks were not statistically significant (P>.05). High ICC values (0.977 to 0.998) for the interlandmark distances further indicated the high degree of consistency between the digital and stone casts. The maxillary prostheses showed good clinical effectiveness, indicating that the corresponding digital casts met the requirements for clinical application. Based on multisource data from spiral CT and the intraoral scanner, 3D digital casts of maxillary defects were generated using the registration technique. These casts were consistent with conventional stone casts in terms of accuracy and were suitable for clinical use. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Cast Stone Formulation At Higher Sodium Concentrations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K. M.; Roberts, K. A.; Edwards, T. B.

2013-09-17

A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, includingmore » production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leach indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste form. The thermal analyses completed in this study provide some preliminary insight, although the limited range of the factors in the test matrix hindered the identification of individual component effects. Future work should involve broader factor ranges to identify the roles played by each of the components in the mix via thermal analyses, analytical microscopy, and characterization of phase formation.« less

Cast Stone Formulation At Higher Sodium Concentrations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K. M.; Edwards, T. A.; Roberts, K. B.

2013-10-02

A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, includingmore » production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leach indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste form. The thermal analyses completed in this study provide some preliminary insight, although the limited range of the factors in the test matrix hindered the identification of individual component effects. Future work should involve broader factor ranges to identify the roles played by each of the components in the mix via thermal analyses, analytical microscopy, and characterization of phase formation.« less

Cast Stone Formulation At Higher Sodium Concentrations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, K. M.; Roberts, K. A.; Edwards, T. B.

2014-02-28

A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, includingmore » production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leachability indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste form. The thermal analyses completed in this study provide some preliminary insight, although the limited range of the factors in the test matrix hindered the identification of individual component effects. Future work should involve broader factor ranges to identify the roles played by each of the components in the mix via thermal analyses, analytical microscopy, and characterization of phase formation.« less

Phase 2 testing results of immobilization of WTP effluent management facility vaporator bottoms simulant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reigel, M.; Cozzi, A.; McCabe, D.

2017-09-08

The Hanford Waste Treatment and Immobilization Plant (WTP) Low Activity Waste (LAW) vitrification facility will generate an aqueous condensate recycle stream (LAW Melter Off-Gas Condensate) from the primary off-gas system. This work examined three waste form formulations based on previous testing with related simulants: 8 wt% ordinary portland cement (OPC), 47 wt% blast furnace slag (BFS), 45 wt% fly ash (FA) known as Cast Stone formulation; 20 wt% Aquaset® II-GH and 80 wt% BFS; 20 wt% OPC and 80 wt% BFS. These tests successfully produced one waste form that set within five days (Cast Stone formulation); however the other twomore » formulations, Aquaset® II-GH/BFS and OPC/BFS, took approximately eight and fourteen days to set, respectively.« less

Technical Approach for Determining Key Parameters Needed for Modeling the Performance of Cast Stone for the Integrated Disposal Facility Performance Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yabusaki, Steven B.; Serne, R. Jeffrey; Rockhold, Mark L.

2015-03-30

Washington River Protection Solutions (WRPS) and its contractors at Pacific Northwest National Laboratory (PNNL) and Savannah River National Laboratory (SRNL) are conducting a development program to develop / refine the cementitious waste form for the wastes treated at the ETF and to provide the data needed to support the IDF PA. This technical approach document is intended to provide guidance to the cementitious waste form development program with respect to the waste form characterization and testing information needed to support the IDF PA. At the time of the preparation of this technical approach document, the IDF PA effort is justmore » getting started and the approach to analyze the performance of the cementitious waste form has not been determined. Therefore, this document looks at a number of different approaches for evaluating the waste form performance and describes the testing needed to provide data for each approach. Though the approach addresses a cementitious secondary aqueous waste form, it is applicable to other waste forms such as Cast Stone for supplemental immobilization of Hanford LAW. The performance of Cast Stone as a physical and chemical barrier to the release of contaminants of concern (COCs) from solidification of Hanford liquid low activity waste (LAW) and secondary wastes processed through the Effluent Treatment Facility (ETF) is of critical importance to the Hanford Integrated Disposal Facility (IDF) total system performance assessment (TSPA). The effectiveness of cementitious waste forms as a barrier to COC release is expected to evolve with time. PA modeling must therefore anticipate and address processes, properties, and conditions that alter the physical and chemical controls on COC transport in the cementitious waste forms over time. Most organizations responsible for disposal facility operation and their regulators support an iterative hierarchical safety/performance assessment approach with a general philosophy that modeling provides the critical link between the short-term understanding from laboratory and field tests, and the prediction of repository performance over repository time frames and scales. One common recommendation is that experiments be designed to permit the appropriate scaling in the models. There is a large contrast in the physical and chemical properties between the Cast Stone waste package and the IDF backfill and surrounding sediments. Cast Stone exhibits low permeability, high tortuosity, low carbonate, high pH, and low Eh whereas the backfill and native sediments have high permeability, low tortuosity, high carbonate, circumneutral pH, and high Eh. These contrasts have important implications for flow, transport, and reactions across the Cast Stone – backfill interface. Over time with transport across the interface and subsequent reactions, the sharp geochemical contrast will blur and there will be a range of spatially-distributed conditions. In general, COC mobility and transport will be sensitive to these geochemical variations, which also include physical changes in porosity and permeability from mineral reactions. Therefore, PA modeling must address processes, properties, and conditions that alter the physical and chemical controls on COC transport in the cementitious waste forms over time. Section 2 of this document reviews past Hanford PAs and SRS Saltstone PAs, which to date have mostly relied on the lumped parameter COC release conceptual models for TSPA predictions, and provides some details on the chosen values for the lumped parameters. Section 3 provides more details on the hierarchical modeling strategy and processes and mechanisms that control COC release. Section 4 summarizes and lists the key parameters for which numerical values are needed to perform PAs. Section 5 provides brief summaries of the methods used to measure the needed parameters and references to get more details.« less

Accuracy of fit of implant-supported bars fabricated on definitive casts made by different dental stones

PubMed Central

Kioleoglou, Ioannis; Pissiotis, Argirios

2018-01-01

Background The purpose of this study was to evaluate the accuracy of fitting of an implant supported screw-retained bar made on definitive casts produced by 4 different dental stone products. Material and Methods The dental stones tested were QuickRock (Protechno), FujiRock (GC), Jade Stone (Whip Mix) and Moldasynt (Heraeus). Three external hexagon implants were placed in a polyoxymethylene block. Definitive impressions were made using monophase high viscosity polyvinylsiloxane in combination with custom trays. Then, definitive models from the different types of dental stones were fabricated. Three castable cylinders with a machined non-enganging base were cast and connected with a very small quantity of PMMA to a cast bar, which was used to verify the marginal discrepancies between the abutments and the prosthetic platforms of the implants. For that purpose special software and a camera mounted on an optical microscope were used. The gap was measured by taking 10 measurements on each abutment, after the Sheffield test was applied. Twelve definitive casts were fabricated for each gypsum product and 40 measurements were performed for each cast. Mean, minimum, and maximum values were calculated. The Shapiro-Wilk test of normality was performed. Mann-Whitney test (P<.06) was used for the statistical analysis of the measurements. Results The non-parametric Kruskal-Wallis test revealed a statistically significant effect of the stone factor on the marginal discrepancy for all Sheffield test combinations: 1. Abutment 2 when screw was fastened on abutment 1 (χ2=3, df=35.33, P<0.01), 2. Abutment 3 when the screw was fastened on abutment 1 (χ2=3, df=37.74, P<0.01), 3. Abutment 1 when the screw was fastened on abutment 3 (χ2=3, df=39.79, P<0.01), 4. Abutment 2 when the screw was fastened on abutment 3 (χ2=3, df=37.26, P<0.01). Conclusions A significant correlation exists between marginal discrepancy and different dental gypsum products used for the fabrication of definitive casts for implant supported bars. The smallest marginal discrepancy was noted on implant supported bars fabricated on definitive casts made by Type III mounting stone. The biggest marginal discrepancy was noted on implant supported bars fabricated on definitive casts made by Type V dental stone. The marginal discrepancies presented on implant supported bars fabricated on definitive casts made by two types of Type IV dental stone were not significantly different. Key words:Dental implant, passive fit, dental stones, marginal discrepancy. PMID:29721227

Secondary Waste Cementitious Waste Form Data Package for the Integrated Disposal Facility Performance Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cantrell, Kirk J.; Westsik, Joseph H.; Serne, R Jeffrey

A review of the most up-to-date and relevant data currently available was conducted to develop a set of recommended values for use in the Integrated Disposal Facility (IDF) performance assessment (PA) to model contaminant release from a cementitious waste form for aqueous wastes treated at the Hanford Effluent Treatment Facility (ETF). This data package relies primarily upon recent data collected on Cast Stone formulations fabricated with simulants of low-activity waste (LAW) and liquid secondary wastes expected to be produced at Hanford. These data were supplemented, when necessary, with data developed for saltstone (a similar grout waste form used at themore » Savannah River Site). Work is currently underway to collect data on cementitious waste forms that are similar to Cast Stone and saltstone but are tailored to the characteristics of ETF-treated liquid secondary wastes. Recommended values for key parameters to conduct PA modeling of contaminant release from ETF-treated liquid waste are provided.« less

[Cervical adaptation of complete cast crowns of various metal alloys, with and without die spacers].

PubMed

Stephano, C B; Roselino, R F; Roselino, R B; Campos, G M

1989-01-01

A metallic replica from a dental preparation for crown was used to make 8 class-IV stone dies. The wax patterns for the casting of the crowns were obtained in two conditions: a) from the stone die with no spacer; and b) from the stone die with an acrylic spacer. Thus, 64 metallic crowns were casted, using 4 different alloys: DURACAST (Cu-Al), NICROCAST (Ni-Cr) and DURABOND (Ni-Cr), and gold. The casted crowns were fitted in the metallic replica and measured as to the cervical discrepance of fitting. The results showed that the use of die spacers decreases the clinical discrepancies of fitting of the casted crowns (in a statistically significant level), no matter the metallic alloy employed.

Effect of microwave disinfection on compressive and tensile strengths of dental stones.

PubMed

Robati Anaraki, Mahmood; Moslehifard, Elnaz; Aminifar, Soran; Ghanati, Hamed

2013-01-01

Although microwave irradiation has been used for disinfection of dental stone casts, there are concerns regarding mechanical damage to casts during the process. The aim of this study was to evaluate the effect of microwave irradiation on the compressive strength (CS) and diametral tensile strength (DTS) of stone casts. In this in vitro study, 80 cylindrical type III and IV stone models (20 × 40 mm) were prepared and divided into 8 groups of 10. The DTS and CS of the specimens were measured by a mechanical testing machine at a crosshead speed of 0.5 cm/min after 7 times of frequent wetting, irradiating at an energy level of 600 W for 3 minutes and cooling. Data were analyzed by Student's t-test. Microwave irradiation significantly increased DTS of type III and IV to 5.23 ± 0.64 and 8.17 ± 0.94, respectively (P < 0.01). According to the results, microwave disinfection increases DTS of type III and IV stone casts without any effects on their CS.

Influence of polyurethane resin dies on the fit and adaptation of full veneer crowns.

PubMed

Lillywhite, Graeme R R; Vohra, Fahim

2015-01-01

Polyurethane resin is a possible alternative to type IV dental stone for fabrication of indirect restorations however its dimensional accuracy is questionable. The aim was to investigate the dimensional accuracy of silica filled polyurethane resin die material by evaluating the marginal fit and adaptation of indirect gold castings. Experimental, in vitro study. Totally 40 copper plated replicas of a nickel chrome master die analogous to a veneer gold crown preparation were made and impressions recorded using polyvinylsiloxane material. Twenty impressions were poured in type IV dental stone (control group (Vel-mix, Kerr, UK) and the remaining (n = 20) in silica filled polyurethane die material (test group) (Alpha Die MF, CA, USA). Gold castings were fabricated for each die using standardized techniques. The castings were seated on their respective copper plated dies, embedded in resin and sectioned. The specimens were analyzed by measuring marginal opening and the area beneath the casting at a ×63 magnification and using image analysis software. Data were analyzed using a Student's t-test. No significant difference was observed between the experimental groups (P > 0.05). The mean marginal opening for type IV, dental stone and polyurethane resin, was 57 ± 22.6 μm and 63.47 ± 27.1 μm, respectively. Stone displayed a smaller area beneath the casting (31581 ± 16297 μm 2 ) as compared to polyurethane resin (35003 ± 23039 μm 2 ). The fit and adaptation of indirect gold castings made on polyurethane and type IV dental stone dies were comparable.

Analysis of Monolith Cores from an Engineering Scale Demonstration of a Prospective Cast Stone Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C. L.; Cozzi, A. D.; Hill, K. A.

2016-06-01

The primary disposition path of Low Activity Waste (LAW) at the DOE Hanford Site is vitrification. A cementitious waste form is one of the alternatives being considered for the supplemental immobilization of the LAW that will not be treated by the primary vitrification facility. Washington River Protection Solutions (WRPS) has been directed to generate and collect data on cementitious or pozzolanic waste forms such as Cast Stone. This report documents the coring and leach testing of monolithic samples cored from an engineering-scale demonstration (ES Demo) with non-radioactive simulants. The ES Demo was performed at SRNL in October of 2013 usingmore » the Scaled Continuous Processing Facility (SCPF) to fill an 8.5 ft. diameter x 3.25 ft. high container with simulated Cast Stone grout. The Cast Stone formulation was chosen from the previous screening tests. Legacy salt solution from previous Hanford salt waste testing was adjusted to correspond to the average LAW composition generated from the Hanford Tank Waste Operation Simulator (HTWOS). The dry blend materials, ordinary portland cement (OPC), Class F fly ash, and ground granulated blast furnace slag (GGBFS or BFS), were obtained from Lafarge North America in Pasco, WA. In 2014 core samples originally obtained approximately six months after filling the ES Demo were tested along with bench scale molded samples that were collected during the original pour. A latter set of core samples were obtained in late March of 2015, eighteen months after completion of the original ES Demo. Core samples were obtained using a 2” diameter x 11” long coring bit. The ES Demo was sampled in three different regions consisting of an outer ring, a middle ring and an inner core zone. Cores from these three lateral zones were further segregated into upper, middle and lower vertical segments. Monolithic core samples were tested using the Environmental Protection Agency (EPA) Method 1315, which is designed to provide mass transfer rates (release rates) of inorganic analytes contained in monolithic material under diffusion controlled release conditions as a function of leaching time. Compressive strength measurements and drying tests were also performed on the 2015 samples. Leachability indices reported are based on analyte concentrations determined from dissolution of the dried samples.« less

A comparative evaluation of the marginal adaptation of a thermoplastic resin, a light cured wax and an inlay casting wax on stone dies: An in vitro study.

PubMed

Gopalan, Reji P; Nair, Vivek V; Harshakumar, K; Ravichandran, R; Lylajam, S; Viswambaran, Prasanth

2018-01-01

Different pattern materials do not produce copings with satisfactory, marginal accuracy when used on stone dies at varying time intervals. The purpose of this study was to evaluate and compare the vertical marginal accuracy of patterns formed from three materials, namely, thermoplastic resin, light cured wax and inlay casting wax at three-time intervals of 1, 12, and 24 h. A master die (zirconia abutment mimicking a prepared permanent maxillary central incisor) and metal sleeve (direct metal laser sintering crown #11) were fabricated. A total of 30 stone dies were obtained from the master die. Ten patterns were made each from the three materials and stored off the die at room temperature. The vertical marginal gaps were measured using digital microscope at 1, 12, and 24 h after reseating with gentle finger pressure. The results revealed a significant statistical difference in the marginal adaptation of three materials at all the three-time intervals. Light cured wax was found to be most accurate at all time intervals, followed by thermoplastic resin and inlay casting wax. Furthermore, there was a significant difference between all pairs of materials. The change in vertical marginal gap from 1 to 24 h between thermoplastic resin and light cured wax was not statistically significant. The marginal adaptation of all the three materials used, was well within the acceptable range of 25-70 μm. The resin pattern materials studied revealed significantly less dimensional change than inlay casting wax on storage at 1, 12, and 24 h time intervals. They may be employed in situations where high precision and delayed investing is expected.

Assessment of the Cast Stone Low-Temperature Waste Form Technology Coupled with Technetium Removal - 14379

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Christopher F.; Rapko, Brian M.; Serne, R. Jeffrey

2014-03-03

The U.S. Department of Energy Office of Environmental Management (EM) is engaging the national laboratories to provide the scientific and technological rigor to support EM program and project planning, technology development and deployment, project execution, and assessment of program outcomes. As an early demonstration of this new responsibility, Pacific Northwest National Laboratory (PNNL) and Savannah River National Laboratory (SRNL) were chartered to implement a science and technology program addressing low-temperature waste forms for immobilization of DOE aqueous waste streams, including technetium removal as an implementing technology. As a first step, the laboratories examined the technical risks and uncertainties associated withmore » the Cast Stone waste immobilization and technetium removal projects at Hanford. Science and technology gaps were identified for work associated with 1) conducting performance assessments and risk assessments of waste form and disposal system performance, and 2) technetium chemistry in tank wastes and separation of technetium from waste processing streams. Technical approaches to address the science and technology gaps were identified and an initial sequencing priority was suggested. A subset of research was initiated in 2013 to begin addressing the most significant science and technology gaps. The purpose of this paper is to report progress made towards closing these gaps and provide notable highlights of results achieved to date.« less

Engineering scale demonstration of a prospective Cast Stone process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cozzi, A.; Fowley, M.; Hansen, E.

2014-09-30

This report documents an engineering-scale demonstration with non-radioactive simulants that was performed at SRNL using the Scaled Continuous Processing Facility (SCPF) to fill an 8.5 ft container with simulated Cast Stone grout. The Cast Stone formulation was chosen from the previous screening tests. Legacy salt solution from previous Hanford salt waste testing was adjusted to correspond to the average composition generated from the Hanford Tank Waste Operation Simulator (HTWOS). The dry blend materials, ordinary portland cement (OPC), Class F fly ash, and ground granulated blast furnace slag (GGBFS or BFS), were obtained from Lafarge North America in Pasco, WA. Overmore » three days, the SCPF was used to fill a 1600 gallon container, staged outside the facility, with simulated Cast Stone grout. The container, staged outside the building approximately 60 ft from the SCPF, was instrumented with x-, y-, and z-axis thermocouples to monitor curing temperature. The container was also fitted with two formed core sampling vials. For the operation, the targeted grout production rate was 1.5 gpm. This required a salt solution flow rate of approximately 1 gpm and a premix feed rate of approximately 580 lb/h. During the final day of operation, the dry feed rate was increased to evaluate the ability of the system to handle increased throughput. Although non-steady state operational periods created free surface liquids, no bleed water was observed either before or after operations. The final surface slope at a fill height of 39.5 inches was 1-1.5 inches across the 8.5 foot diameter container, highest at the final fill point and lowest diametrically opposed to the fill point. During processing, grout was collected in cylindrical containers from both the mixer discharge and the discharge into the container. These samples were stored in a humid environment either in a closed box proximal to the container or inside the laboratory. Additional samples collected at these sampling points were analyzed for rheological properties and density. Both the rheological properties (plastic viscosity and yield strength) and density were consistent with previous and later SCPF runs.« less

Position Accuracy of Implant Analogs on 3D Printed Polymer versus Conventional Dental Stone Casts Measured Using a Coordinate Measuring Machine.

PubMed

Revilla-León, Marta; Gonzalez-Martín, Óscar; Pérez López, Javier; Sánchez-Rubio, José Luis; Özcan, Mutlu

2017-11-17

To compare the accuracy of implant analog positions on complete edentulous maxillary casts made of either dental stone or additive manufactured polymers using a coordinate measuring machine (CMM). A completely edentulous maxillary model of a patient with 7 implant analogs was obtained. From this model, two types of casts were duplicated, namely conventional dental stone (CDS) using a custom tray impression technique after splinting (N = 5) and polymer cast using additive manufacturing based on the STL file generated. Polymer casts (N = 20; n = 5 per group) were fabricated using 4 different additive manufacturing technologies (multijet printing-MJP1, direct light processing-DLP, stereolithography-SLA, multijet printing-MJP2). CMM was used to measure the correct position of each implant, and distortion was calculated for each system at x-, y-, and z-axes. Measurements were repeated 3 times per specimen in each axis yielding a total of 546 measurements. Data were analyzed using ANOVA, Sheffé tests, and Bonferroni correction (α = 0.05). Compared to CMM, the mean distortion (μm) ranged from 22.7 to 74.9, 23.4 to 49.1, and 11.0 to 85.8 in the x-, y-, and z-axes, respectively. CDS method (x-axis: 37.1; z-axis: 27.62) showed a significant difference compared to DLP on the x-axis (22.7) (p = 0.037) and to MJP1 on the z-axis (11.0) (p = 0.003). Regardless of the cast system, x-axes showed more distortion (42.6) compared to y- (34.6) and z-axes (35.97). Among additive manufacturing technologies, MJP2 presented the highest (64.3 ± 83.6), and MJP1 (21.57 ± 16.3) and DLP (27.07 ± 20.23) the lowest distortion, which was not significantly different from CDS (32.3 ± 22.73) (p > 0.05). For the fabrication of the definitive casts for implant prostheses, one of the multijet printing systems and direct light processing additive manufacturing technologies showed similar results to conventional dental stone. Conventional dental stone casts could be accurately duplicated using some of the additive manufacturing technologies tested. © 2017 by the American College of Prosthodontists.

Effect of imaging powder and CAD/CAM stone types on the marginal gap of zirconia crowns.

PubMed

Alghazzawi, Tariq F; Al-Samadani, Khalid H; Lemons, Jack; Liu, Perng-Ru; Essig, Milton E; Bartolucci, Alfred A; Janowski, Gregg M

2015-02-01

To compare the marginal gap using different types of die stones and titanium dies with and without powders for imaging. A melamine tooth was prepared and scanned using a laboratory 3-shape scanner to mill a polyurethane die, which was duplicated into different stones (Jade, Lean, CEREC) and titanium. Each die was sprayed with imaging powders (NP, IPS, Optispray, Vita) to form 15 groups. Ten of each combination of stone/titanium and imaging powders were used to mill crowns. A light-bodied impression material was injected into the intaglio surface of each crown and placed on the corresponding die. Each crown was removed, and the monophase material was injected to form a monophase die, which was cut into 8 sections. Digital images were captured using a stereomicroscope to measure marginal gap. Scanning electron microscopy was used to determine the particle size and shape of imaging powders and stones. Marginal gaps ranged from mean (standard deviation) 49.32 to 1.20 micrometers (3.97-42.41 μm). There was no statistical difference (P > .05) in the marginal gap by any combination of stone/titanium and imaging powders. All of the imaging powders had a similar size and rounded shape, whereas the surface of the stones showed different structures. When a laboratory 3-shape scanner is used, all imaging powders performed the same for scanning titanium abutments. However, there was no added value related to the use of imaging powder on die stone. It is recommended that the selection of stone for a master cast be based on the hysical properties. When a laboratory 3-shape scanner is used, the imaging powder is not required for scanning die stone. Whenever scanning titanium implant abutments, select the least expensive imaging powder. Copyright © 2015 American Dental Association. Published by Elsevier Inc. All rights reserved.

Marginal adaptation of four inlay casting waxes on stone, titanium, and zirconia dies.

PubMed

Michalakis, Konstantinos X; Kapsampeli, Vassiliki; Kitsou, Aikaterini; Kirmanidou, Yvone; Fotiou, Anna; Pissiotis, Argirios L; Calvani, Pasquale Lino; Hirayama, Hiroshi; Kudara, Yukio

2014-07-01

Different inlay casting waxes do not produce copings with satisfactory marginal accuracy when used on different die materials. The purpose of this study was to evaluate the marginal accuracy of 4 inlay casting waxes on stone dies and titanium and zirconia abutments and to correlate the findings with the degree of wetting between the die specimens and the inlay casting waxes. The inlay casting waxes tested were Starwax (Dentaurum), Unterziehwachs (Bredent), SU Esthetic wax (Schuler), and Sculpturing wax (Renfert). The marginal opening of the waxes was measured with a stereomicroscope on high-strength stone dies and on titanium and zirconia abutments. Photographic images were obtained, and the mean marginal opening for each specimen was calculated. A total of 1440 measurements were made. Wetting between die materials and waxes was determined after fabricating stone, titanium, and zirconia rectangular specimens. A calibrated pipette was used to place a drop of molten wax onto each specimen. The contact angle was calculated with software after an image of each specimen had been made with a digital camera. Collected data were subjected to a 2-way analysis of variance (α=.05). Any association between marginal accuracy and wetting of different materials was found by using the Pearson correlation. The wax factor had a statistically significant effect both on the marginal discrepancy (F=158.31, P<.001) and contact angle values (F=68.09, P<.001). A statistically significant effect of the die material factor both on the marginal adaptation (F=503.47, P<.001) and contact angle values (F=585.02, P<.001) was detected. A significant correlation between the marginal accuracy and the contact angle values (Pearson=0.881, P=.01) was also found. Stone dies provided wax copings with the best marginal integrity, followed by titanium and zirconia abutments. Unterziehwachs (Bredent), wax produced the best marginal adaptation on different die materials. A significant correlation was found between the marginal accuracy and the contact angle values. As the contact angle value became smaller, the marginal accuracy improved. All combinations of waxes and stone and titanium dies presented a high wettability. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Getters for Tc and I Removal from Liquid Waste

NASA Astrophysics Data System (ADS)

Qafoku, N. P.; Asmussen, M.; Lawter, A.; Neeway, J.; Smith, G.

2015-12-01

A cementitious waste form, Cast Stone, is being evaluated as a possible supplemental waste form for the low activity waste (LAW) at the Hanford Site, which contains significant amounts of radioactive 99Tc and 129I, as part of the tank waste cleanup mission. To improve the retention of Tc and/or I in Cast Stone, materials with a high affinity for Tc and/or I, termed "getters," can be added to decrease the rate of contaminant release and diffusivity, and improve Cast Stone performance. A series of kinetic batch sorption experiments was performed to determine the effectiveness of the getter materials. Several Tc getters [blast furnace slag, Sn (II) apatite, SnCl2, nanoporous Sn phosphate, KMS-2 (a potassium-metal-sulfide), and Sn(II) hydroxyapatite] and I getters [layered Bi hydroxide, natural argentite mineral, synthetic argentite, Ag-impregnated carbon, and Ag-exchanged zeolite] were tested in different solution media, 18.2 MΩ DI H2O and a caustic LAW waste simulant containing 6.5 M Na or 7.8 M Na. The experiments were conducted at room temperature in the presence or absence of air. Results indicated that most Tc getters (with the exception of KMS-2) performed better in the DI H2O solution than in the 6.5 and 7.8 M Na LAW simulant. In addition, Tc sequestration may be affected by the presence of other redox sensitive elements that were present in the LAW simulant, such as Cr. The Tc getter materials have been examined through various solid-state characterization techniques such as XRD, SEM/EDS, XANES and EXAFS which provided evidence for plausible mechanisms of aqueous Tc removal. The results indicated that the Tc precipitates differ depending on the getter material and that Tc(VII) is reduced to Tc(IV) in most of the getters but to a differing extents. For the I getters, Ag-exchanged zeolite and synthetic argentite were the most effective ones. The other I getters showed limited effectiveness for sorbing I under the high ionic strength and caustic conditions of the LAW simulant.

DETAIL VIEW OF BASE OF CAST IRON TOWER SHOWING THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW OF BASE OF CAST IRON TOWER SHOWING THE FABRICATING MARK OF STARBUCK IRON WORKS, TROY, NY - Bidwell Bar Suspension Bridge & Stone Toll House, Near Lake Oroville (moved from fork of Feather River), Oroville, Butte County, CA

Cast Stone Formulation for Nuclear Waste Immobilization at Higher Sodium Concentrations

DOE PAGES

Fox, Kevin; Cozzi, Alex; Roberts, Kimberly; ...

2014-11-01

Low activity radioactive waste at U.S. Department of Energy sites can be immobilized for permanent disposal using cementitious waste forms. This study evaluated waste forms produced with simulated wastes at concentrations up to twice that of currently operating processes. The simulated materials were evaluated for their fresh properties, which determine processability, and cured properties, which determine waste form performance. The results show potential for greatly reducing the volume of material. Fresh properties were sufficient to allow for processing via current practices. Cured properties such as compressive strength meet disposal requirements. Leachability indices provide an indication of expected long-term performance.

Utilisation of Sand from Kaolin Washing for the Manufacture of Alkali-activated Artificial Sandstone

NASA Astrophysics Data System (ADS)

Vavro, Martin; Vavro, Leona; Mec, Pavel; Soucek, Kamil; Pticen, Frantisek; Reiterman, Pavel

2017-04-01

Sandstones represent a traditional natural stones which are widely used in Czech architecture and sculpture over a long time. Thanks to their relatively easy workability, sandstones provide a wide range of stone products and also represent a popular material for architectural and sculptural purposes. In the field of restoration of artworks, they are therefore often used for manufacturing stone statue copies originally made from the same or similar type of stone. Despite a relatively common and varied occurrence of natural sandstones, the method of the artificial stone facsimiles creation in the form of various cast elements is also often applied in restoration practice. The history of application of artificial stones in civil engineering and architecture goes back to the ancient times, i.e. to Roman antiquity and possibly up to the time of ancient Egypt. The lack of appropriate natural rock, suitable in the view of colour, grain size or texture is the main reason of manufacturing copies based on synthetic mixtures. The other reason is high financial costs to create a sculpture copy from natural materials. Mixtures made from white and/or grey cements, sands, carefully selected crushed stone or well graded natural gravels, and mineral coloring pigments or mixtures with acrylate, polyester, and epoxy resins binder are the most frequently used artificial materials for cast stone manufacturing. This paper aims to bring information about composition and properties of artificial sandstones made from alkali-activated binder mixtures based on metakaolin and granulated blast furnace slag. The filler of this artificial stone is represented by fine-grained sand generated during kaolin wet processing. Used sand is mainly formed by quartz, feldspars, micas (muscovite > biotite), residual kaolin, and to a lesser extent also by Fe oxyhydroxides ("limonite"), titanium dioxide mineral (probably anatase), and carbonate mineral unidentified in detail. Annual Czech production of this sand from kaolin-washing process is of several hundred thousand tonnes and it thus represent so far a relatively rarely used natural building material which is currently usually deposited in worked-out areas of kaolin quarries. One of the main reasons of very difficult usability of this sands in building material industry is their behavior when exposed to the weather. In only a very short time of exposure in outdoor condition they may change in colour from greyish white to yellow-brown or golden yellow. This colour change is accompanied by significant decrease of pH values of sand leachate up to pH ranging between 3.5 and 5.5, in extreme cases even up to 2.0. Despite these extreme chemical properties of sands under study, the artificial sandstone, very similar in the physical and mechanical properties to natural ones, was successfully prepared in the laboratory. Due to the mineralogical composition of applied sands (i.e. the presence not only of quartz, but also of feldspar and muscovite), the artificial sandstone is characterized by relatively true natural appearance.

Preparation of artificial kidney stones of reproducible size, shape, and mass by precision injection molding.

PubMed

Carey, Robert I; Kyle, Christopher C; Carey, Donna L; Leveillee, Raymond J

2008-01-01

To prepare artificial kidney stones of defined shape, size, mass, and material composition via precision injection molding of Ultracal 30 cement slurries into an inexpensive biodegradable mold. A calcium alginate and silica-based mold was used to prepare casts of varying shapes in a reproducible manner. Ultracal 30 cement slurries mixed 1:1 with water were injected into these casts and allowed to harden. The artificial stones were recovered and their physical properties determined. Ex-vivo and in-vivo responses to holmium laser lithotripsy were examined. Spheres, half spheres, cylinders, cubes, tapered conical structures, and flat angulated structures were prepared with high precision without post-molding manipulations. Large spheres of average mass 0.661 g (+/- 0.037), small spheres of average mass 0.046 g (+/- 0.0026), and hexagons of average mass 0.752 g (+/- 0.0180) were found to have densities (1610-1687 kg/m(3)) within the expected range for Ultracal 30 cement stones. Ex-vivo holmium laser lithotripsy of small spheres in saline showed uniformly reproducible efficiencies of comminution. Implantation of a tapered conical stone into the ureter of a porcine model demonstrated stone comminution in vivo consistent with that seen in the ex-vivo models. We present an environmentally safe, technically simple procedure for the formation of artificial kidney stones of predetermined size and shape. The technique does not require the use of hazardous solvents or postprocedural processing of the stones. These stones are intended for use in standardized experiments of lithotripsy efficiency in which the shape of the stone as well as the mass can be predetermined and precisely controlled.

Patio Stone Project Gives Students a Concrete Learning Experience

ERIC Educational Resources Information Center

Fitzgerald, Mike

2005-01-01

In this article, the author presents an overview of concrete as a building material and as an example of a particle composite, and discusses the origins of concrete in ancient Rome. He then describes an activity in which students can cast a concrete patio stone. Students can apply the technological design process, as well as the elements of…

Fractography of cast gypsum.

PubMed

Mori, T; Yamane, M

1982-02-01

A fractographical study of dental cast gypsum was made in order to correlate the mechanical properties with the microstructure. Wet specimens fractured under tensile stress showed intercrystalline fracture and the tensile strength depended on the porosity present. Thus, it was assumed that tensile strength was dependent on the contact area between individual gypsum crystals and changes in porosity approximated to changes in contact area. Strength differences among specimens of a given W/P ratio, therefore, can be related to differences in intercrystalline contact areas. These theoretical considerations suggest that the classification of dental die stone and dental stone into high and low strength types based on strength properties only would be more practical and less confusing than at present.

Calcium hypochlorite as a disinfecting additive for dental stone.

PubMed

Twomey, Jonathan O; Abdelaziz, Khalid M; Combe, Edward C; Anderson, Dwight L

2003-09-01

Dental casts come into direct contact with impression materials and other items that are contaminated by saliva and blood from a patient's mouth, leaving the casts susceptible to cross-contamination. Topical methods of disinfecting casts are difficult to control, while immersion methods are potentially destructive. Thus, an additional method to control cross-contamination between patients and laboratory personnel is needed. This study was undertaken in an attempt to develop a dental stone with disinfecting properties and adequate compressive and tensile strengths. Calcium hypochlorite [Ca(OCl)(2)] in aqueous solution in concentrations from 0 to 1.5% was tested as a disinfecting additive to type V dental stone. The compressive and tensile strength properties of the modified stone were measured (MPa) using a universal testing machine at a consistency similar to unmodified stone. Strength data were analyzed by 1-way ANOVA and post hoc Tukey-Kramer procedure (alpha < or =.05). To measure the disinfecting ability, the effect on Bacillis subtilis bacteriophage phi29 was tested in triplicate to find the minimum concentration at which no phage was detected. Additionally, 3 impressions were disinfected with CaviCide, and 3 impressions rinsed in water served as controls. In general, the effect of adding the disinfectant to the stone was a decrease in strength. Exceptions were the dry compressive strength, for which there was a significant increase in strength (P=.048) at 0.5%, and the wet compressive and wet tensile strength, which showed no significant difference between the 1.5% and the control. When Ca(OCl)(2) was added at the concentration 0.5% (2765 ppm available chlorine), the gypsum had acceptable mechanical properties; dry compressive strength was 78.86 +/- 4.12 MPa, and dry tensile strength was 10.64 +/- 1.27 MPa, compared to control values of 67.85 +/- 6.28 and 13.41 +/- 1.24 MPa, respectively. At concentrations of 0.3% and higher (36 1650 ppm of available chlorine), calcium hypochlorite was able to completely inactivate phi29. It is possible to prepare a type V dental stone that contains a disinfectant, has adequate mechanical properties, and will reduce numbers of residual microorganisms. For example, stone mixed with water containing 0.5% Ca(OCl)(2) meets these criteria.

Effect of palm oil fuel ash on compressive strength of palm oil boiler stone lightweight aggregate concrete

NASA Astrophysics Data System (ADS)

Muthusamy, K.; Zamri, N. A.; Kusbiantoro, A.; Lim, N. H. A. S.; Ariffin, M. A. Mohd

2018-04-01

Both palm oil fuel ash (POFA) and palm oil boiler stone (POBS) are by-products which has been continuously generated by local palm oil mill in large amount. Both by products is usually disposed as profitless waste and considered as nuisance to environment. The present research investigates the workability and compressive strength performance of lightweight aggregate concrete (LWAC) made of palm oil boiler stone (POBS) known as palm oil boiler stone lightweight aggregate concrete (POBS LWAC) containing various content of palm oil fuel ash. The control specimen that is POBS LWAC of grade 60 were produced using 100% OPC. Then, another 4 mixes were prepared by varying the POFA percentage from 10%, 20%, 30% and 40% by weight of cement. Fresh mixes were subjected to slump test to determine its workability before casted in form of cubes. Then, all specimens were subjected to water curing up to 28 days and then tested for its compressive strength. It was found out that utilizing of optimum amount of POFA in POBS LWAC would improve the workability and compressive strength of the concrete. However, inclusion of POFA more than optimum amount is not recommended as it will increase the water demand leading to lower workability and strength reduction.

Self-disinfecting Alginate vs Conventional Alginate: Effect on Surface Hardness of Gypsum Cast-An in vitro Study.

PubMed

Madhavan, Ranjith; George, Navia; Thummala, Niharika R; Ravi, S V; Nagpal, Ajay

2017-11-01

For the construction of any dental prosthesis, accurate impressions are necessary. Hence, we undertook the present study to evaluate and compare the surface hardness of gypsum casts poured from impressions made using conventional alginate and self-disinfecting alginate. A total of 30 impressions of stainless steel die were made, out of which 15 impressions were made with conventional alginate and 15 were made with self-disinfecting alginate and poured using Type III dental stone. Thirty stone specimens were subjected for hardness testing. Data were analyzed using independent samples t-test to compare the mean surface hardness. Difference in surface hardness was statistically insignificant (p > 0.05). Surface hardness of gypsum casts poured using impressions made from self-disinfecting alginate and conventional alginates were comparable. Self-disinfecting alginates may be employed in clinical practice as safe and effective materials to overcome the infection control issues without compromising on the properties of the material.

Technetium, Iodine, and Chromium Adsorption/Desorption Kd Values for Vadose Zone Pore Water, ILAW Glass, and Cast Stone Leachates Contacting an IDF Sand Sequence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Last, George V.; Snyder, Michelle M.V.; Um, Wooyong

Performance and risk assessments of immobilized low-activity waste (ILAW) at the Integrated Disposal Facility (IDF) have shown that risks to groundwater are quite sensitive to adsorption-desorption interactions occurring in the near- and far-field environment. These interactions between the underlying sediments and the contaminants present in the leachates that descend from the buried glass, secondary waste grouts, and potentially Cast Stone low-activity waste packages have been represented in these assessments using the contaminant distribution coefficient (Kd) construct. Some contaminants (99Tc, 129I, and Cr) present in significant quantities in these wastes have low Kd values and tend to drive risk to publicmore » health and the environment. Relatively small changes in the Kd value can cause relatively large changes in the retardation factor. Thus, even relatively small uncertainty in the Kd value can result in a relatively large uncertainty in the risk determined through performance assessment modeling. The purpose of this study is to further reduce the uncertainty in Kd values for 99Tc, iodine (iodide and iodate), and Cr (chromate; CrO42-) by conducting systematic adsorption-desorption experiments using actual sand-dominated Hanford formation sediments from beneath the IDF and solutions that closely mimic Hanford vadose zone pore water and leachates from Cast Stone and ILAW glass waste forms. Twenty-four batch and 21 flow-through column experiments were conducted, yielding 261 Kd measurements for these key contaminants, and contributing to our understanding for predicting transport from wastes disposed to the IDF. While the batch Kd methodology is not well-suited for measuring Kd values for non-sorbing species (as noted by the U.S. Environmental Protection Agency), the batch Kd results presented here are not wholly inconsistent with the column Kd results, and could be used for sensitivity purposes. Results from the column experiments are consistent with the best estimate and lower range of Kd values reported by Krupka et al. and Cantrell et al.« less

Supplemental Immobilization Cast Stone Technology Development and Waste Form Qualification Testing Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Westsik, Joseph H.; Serne, R. Jeffrey; Pierce, Eric M.

2013-05-31

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is being constructed to treat the 56 million gallons of radioactive waste stored in 177 underground tanks at the Hanford Site. The WTP includes a pretreatment facility to separate the wastes into high-level waste (HLW) and low-activity waste (LAW) fractions for vitrification and disposal. The LAW will be converted to glass for final disposal at the Integrated Disposal Facility (IDF). The pretreatment facility will have the capacity to separate all of the tank wastes into the HLW and LAW fractions, and the HLW Vitrification Facility will have the capacity to vitrifymore » all of the HLW. However, a second immobilization facility will be needed for the expected volume of LAW requiring immobilization. A number of alternatives, including Cast Stone—a cementitious waste form—are being considered to provide the additional LAW immobilization capacity.« less

SOLIDIFICATION OF THE HANFORD LAW WASTE STREAM PRODUCED AS A RESULT OF NEAR-TANK CONTINUOUS SLUDGE LEACHING AND SODIUM HYDROXIDE RECOVERY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reigel, M.; Johnson, F.; Crawford, C.

2011-09-20

The U.S. Department of Energy (DOE), Office of River Protection (ORP), is responsible for the remediation and stabilization of the Hanford Site tank farms, including 53 million gallons of highly radioactive mixed wasted waste contained in 177 underground tanks. The plan calls for all waste retrieved from the tanks to be transferred to the Waste Treatment Plant (WTP). The WTP will consist of three primary facilities including pretreatment facilities for Low Activity Waste (LAW) to remove aluminum, chromium and other solids and radioisotopes that are undesirable in the High Level Waste (HLW) stream. Removal of aluminum from HLW sludge canmore » be accomplished through continuous sludge leaching of the aluminum from the HLW sludge as sodium aluminate; however, this process will introduce a significant amount of sodium hydroxide into the waste stream and consequently will increase the volume of waste to be dispositioned. A sodium recovery process is needed to remove the sodium hydroxide and recycle it back to the aluminum dissolution process. The resulting LAW waste stream has a high concentration of aluminum and sodium and will require alternative immobilization methods. Five waste forms were evaluated for immobilization of LAW at Hanford after the sodium recovery process. The waste forms considered for these two waste streams include low temperature processes (Saltstone/Cast stone and geopolymers), intermediate temperature processes (steam reforming and phosphate glasses) and high temperature processes (vitrification). These immobilization methods and the waste forms produced were evaluated for (1) compliance with the Performance Assessment (PA) requirements for disposal at the IDF, (2) waste form volume (waste loading), and (3) compatibility with the tank farms and systems. The iron phosphate glasses tested using the product consistency test had normalized release rates lower than the waste form requirements although the CCC glasses had higher release rates than the quenched glasses. However, the waste form failed to meet the vapor hydration test criteria listed in the WTP contract. In addition, the waste loading in the phosphate glasses were not as high as other candidate waste forms. Vitrification of HLW waste as borosilicate glass is a proven process; however the HLW and LAW streams at Hanford can vary significantly from waste currently being immobilized. The ccc glasses show lower release rates for B and Na than the quenched glasses and all glasses meet the acceptance criterion of < 4 g/L. Glass samples spiked with Re{sub 2}O{sub 7} also passed the PCT test. However, further vapor hydration testing must be performed since all the samples cracked and the test could not be performed. The waste loading of the iron phosphate and borosilicate glasses are approximately 20 and 25% respectively. The steam reforming process produced the predicted waste form for both the high and low aluminate waste streams. The predicted waste loadings for the monolithic samples is approximately 39%, which is higher than the glass waste forms; however, at the time of this report, no monolithic samples were made and therefore compliance with the PA cannot be determined. The waste loading in the geopolymer is approximately 40% but can vary with the sodium hydroxide content in the waste stream. Initial geopolymer mixes revealed compressive strengths that are greater than 500 psi for the low aluminate mixes and less than 500 psi for the high aluminate mixes. Further work testing needs to be performed to formulate a geopolymer waste form made using a high aluminate salt solution. A cementitious waste form has the advantage that the process is performed at ambient conditions and is a proven process currently in use for LAW disposal. The Saltstone/Cast Stone formulated using low and high aluminate salt solutions retained at least 97% of the Re that was added to the mix as a dopant. While this data is promising, additional leaching testing must be performed to show compliance with the PA. Compressive strength tests must also be performed on the Cast Stone monoliths to verify PA compliance. Based on testing performed for this report, the borosilicate glass and Cast Stone are the recommended waste forms for further testing. Both are proven technologies for radioactive waste disposal and the initial testing using simulated Hanford LAW waste shows compliance with the PA. Both are resistant to leaching and have greater than 25% waste loading.« less

The use of a 3D laser scanner using superimpositional software to assess the accuracy of impression techniques.

PubMed

Shah, Sinal; Sundaram, Geeta; Bartlett, David; Sherriff, Martyn

2004-11-01

Several studies have made comparisons in the dimensional accuracy of different elastomeric impression materials. Most have used two-dimensional measuring devices, which neglect to account for the dimensional changes that exist along a three-dimensional surface. The aim of this study was to compare the dimensional accuracy of an impression technique using a polyether material (Impregum) and a vinyl poly siloxane material (President) using a laser scanner with three-dimensional superimpositional software. Twenty impressions, 10 with a polyether and 10 with addition silicone, of a stone master model that resembled a dental arch containing three acrylic posterior teeth were cast in orthodontic stone. One plastic tooth was prepared for a metal crown. The master model and the casts were digitised with the non-contacting laser scanner to produce a 3D image. 3D surface viewer software superimposed the master model to the stone replica and the difference between the images analysed. The mean difference between the model and the stone replica made from Impregum was 0.072mm (SD 0.006) and that for the silicone 0.097mm (SD 0.005) and this difference was statistically significantly, p=0.001. Both impression materials provided an accurate replica of the prepared teeth supporting the view that these materials are highly accurate.

Secondary Waste Form Development and Optimization—Cast Stone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sundaram, S. K.; Parker, Kent E.; Valenta, Michelle M.

2011-07-14

Washington River Protection Services is considering the design and construction of a Solidification Treatment Unit (STU) for the Effluent Treatment Facility (ETF) at Hanford. The ETF is a Resource Conservation and Recovery Act-permitted, multi-waste, treatment and storage unit and can accept dangerous, low-level, and mixed wastewaters for treatment. The STU needs to be operational by 2018 to receive secondary liquid wastes generated during operation of the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The STU to ETF will provide the additional capacity needed for ETF to process the increased volume of secondary wastes expected to be produced by WTP.

Waste Acceptance Testing of Secondary Waste Forms: Cast Stone, Ceramicrete and DuraLith

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattigod, Shas V.; Westsik, Joseph H.; Chung, Chul-Woo

2011-08-12

To support the selection of a waste form for the liquid secondary wastes from WTP, Washington River Protection Solutions has initiated secondary-waste-form testing work at Pacific Northwest National Laboratory (PNNL). In anticipation of a down-selection process for a waste form for the Solidification Treatment Unit to be added to the ETF, PNNL is conducting tests on four candidate waste forms to evaluate their ability to meet potential waste acceptance criteria for immobilized secondary wastes that would be placed in the IDF. All three waste forms demonstrated compressive strengths above the minimum 3.45 MPa (500 psi) set as a target formore » cement-based waste forms. Further, none of the waste forms showed any significant degradation in compressive strength after undergoing thermal cycling (30 cycles in a 10 day period) between -40 C and 60 C or water immersion for 90 days. The three leach test methods are intended to measure the diffusion rates of contaminants from the waste forms. Results are reported in terms of diffusion coefficients and a leachability index (LI) calculated based on the diffusion coefficients. A smaller diffusion coefficient and a larger LI are desired. The NRC, in its Waste Form Technical Position (NRC 1991), provides recommendations and guidance regarding methods to demonstrate waste stability for land disposal of radioactive waste. Included is a recommendation to conduct leach tests using the ANS 16.1 method. The resulting leachability index (LI) should be greater than 6.0. For Hanford secondary wastes, the LI > 6.0 criterion applies to sodium leached from the waste form. For technetium and iodine, higher targets of LI > 9 for Tc and LI > 11 for iodine have been set based on early waste-disposal risk and performance assessment analyses. The results of these three leach tests conducted for a total time between 11days (ASTM C1308) to 90 days (ANS 16.1) showed: (1) Technetium diffusivity: ANSI/ANS 16.1, ASTM C1308, and EPA 1315 tests indicated that all the waste forms had leachability indices better than the target LI > 9 for technetium; (2) Rhenium diffusivity: Cast Stone 2M specimens, when tested using EPA 1315 protocol, had leachability indices better than the target LI > 9 for technetium based on rhenium as a surrogate for technetium. All other waste forms tested by ANSI/ANS 16.1, ASTM C1308, and EPA 1315 test methods had leachability indices that were below the target LI > 9 for Tc based on rhenium release. These studies indicated that use of Re(VII) as a surrogate for 99Tc(VII) in low temperature secondary waste forms containing reductants will provide overestimated diffusivity values for 99Tc. Therefore, it is not appropriate to use Re as a surrogate 99Tc in future low temperature waste form studies. (3) Iodine diffusivity: ANSI/ANS 16.1, ASTM C1308, and EPA 1315 tests indicated that the three waste forms had leachability indices that were below the target LI > 11 for iodine. Therefore, it may be necessary to use a more effective sequestering material than silver zeolite used in two of the waste forms (Ceramicrete and DuraLith); (4) Sodium diffusivity: All the waste form specimens tested by the three leach methods (ANSI/ANS 16.1, ASTM C1308, and EPA 1315) exceeded the target LI value of 6; (5) All three leach methods (ANS 16.1, ASTM C1308 and EPA 1315) provided similar 99Tc diffusivity values for both short-time transient diffusivity effects as well as long-term ({approx}90 days) steady diffusivity from each of the three tested waste forms (Cast Stone 2M, Ceramicrete and DuraLith). Therefore, any one of the three methods can be used to determine the contaminant diffusivities from a selected waste form.« less

Bile Cast Nephropathy Caused by Obstructive Cholestasis.

PubMed

Aniort, Julien; Poyet, Anaïs; Kemeny, Jean-Louis; Philipponnet, Carole; Heng, Anne-Elisabeth

2017-01-01

Acute kidney injury (AKI) is a major complication in patients with liver disease. Although hepatorenal syndrome is frequently involved, bile cast nephropathy, characterized by tubular bile cast formation, has been scarcely described in the setting of severe liver failure. Few renal histology studies are available in these patients. We describe a case of bile cast nephropathy in a patient with obstructive cholestasis caused by stones in the common bile duct. The kidney biopsy confirmed this diagnosis, with several green casts in tubular lumens, tubular injury, and bilirubin composition of the tubular casts with Hall stain. The patient had no confounding cause of kidney failure, and complete kidney recovery followed removal of the bile duct obstruction. This case shows that severe cholestasis is sufficient to cause AKI, and that AKI can be reversible after treatment of the biliary obstruction. Copyright © 2016 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Effect of a new tension system, used in acrylic resin flasking, on the dimensional stability of denture bases.

PubMed

Consani, Rafael Leonardo Xediek; Domitti, Saide Sarckis; Consani, Simonides

2002-09-01

The pressure of final closure may be released when the flask is removed from the mechanical or pneumatic press and placed in the spring clamp. This release in pressure may result in dimensional changes that distort the denture base. The purpose of this study was to investigate differences between the dimensional stability of standardized simulated denture bases processed by traditional moist heat-polymerization and those processed by use of a new tension system. A metal master die was fabricated to simulate an edentulous maxillary arch without irregularities in the alveolar ridge walls. A silicone mold of this metallic die was prepared, and 40 stone casts were formed from the mold with type III dental stone. The casts were randomly assigned to 4 test groups (A-D) of 10 specimens each. A uniform denture base pattern was made on each stone cast with a 1.5-mm thickness of base-plate wax, measured with a caliper. The patterns were invested for traditional hot water processing. A polymethyl methacrylate dough was prepared and packed for processing. The flasks in groups A and B were closed with the traditional pressure technique and placed in spring clamps after final closure. The flasks in groups C and D were pressed between the metallic plates of the new tension system after the final closure. The group A and C flasks were immediately immersed in the water processing unit at room temperature (25 degrees +/- 2 degrees C). The unit was programmed to raise the temperature to 74 degrees C over 1 hour, and then maintained the temperature at 74 degrees C for 8 hours. The group B and D flasks were bench stored at room temperature (25 degrees +/- 2 degrees C) for 6 hours and were then subjected to the same moist heat polymerization conditions as groups A and C. All processed dentures were bench cooled for 3 hours. After recovery from the flasks, the base-cast sets were transversally sectioned into 3 parts (corresponding to 3 zones): (1) distal of the canines, (2) mesial of the first molars, and (3) mesial of the posterior palate). These areas had been previously established and standardized by use of a pattern denture in the sawing device to determine the sections in each base-cast set. Base-cast gaps were measured at 5 predetermined points on each section with an optical micrometer that had a tolerance of 0.001 mm. Collected data were analyzed with analysis of variance and Tukey's test. Denture bases processed with the new tension system exhibited significantly better base adaptation than those processed with traditional acrylic resin packing. Immediately after polymerization (Groups A and C), mean dimensional change values were 0.213 +/- 0.055 mm for the traditional packing technique and 0.173 +/- 0.050 mm for new tension system. After delayed polymerization (Groups B and D), the values were 0.216 +/- 0.074 mm for the traditional packing technique and 0.164 +/- 0.032 mm for new tension system. With both techniques, dimensional changes in the posterior palatal zone were greater (conventional = 0.286 +/- 0.038 mm; new system = 0.214 +/- 0.024 mm) than those elsewhere on the base-cast set. Within the limitations of this study, the new tension packing system was associated with decreased dimensional changes in the simulated maxillary denture bases processed with heat-polymerization.

Geological-Technical and Geo-engineering Aspects of Dimensional Stone Underground Quarrying

NASA Astrophysics Data System (ADS)

Fornaro, Mauro; Lovera, Enrico

Underground exploitation of dimensional stones is not a novelty, being long since practised, as proved by a number of historical documents and by a certain number of ancient quarrying voids throughout the world. Anyway, so far, open cast quarrying has been the most adopted practice for the excavation of dimensional stones. One primary reason that led to this situation is of course connected to the lower production costs of an open cast exploitation compared to an underground one. This cheapness has been supported by geological and technical motives: on the one hand, the relative availability of surface deposits and, on the other, the development of technologies, which often can be used only outdoor. But, nowadays, general costs of quarrying activities should be re-evaluated because new, and often proper, restrictions have been strongly rising during recent years. As a consequence of both environmental and technical restrictions, pressure will more and more arise to reduce open cast quarrying and to promote underground exploitations. The trend is already well marked for weak rocks - for instance in the extractive basin of Carrara, where about one hundred quarries are active, 30 per cent is working underground, but also in Spain, Portugal and Greece the number of underground marble quarries is increasing - but not yet for hard rock quarrying, where only few quarries are working underground all around the world. One reason has to be found in cutting technologies traditionally used. In weak rocks, diamond wire saw and chain cutter are usable, with few adaptations, in underground spaces, while drilling and blasting, the traditional exploitation method for hard stone, is not easily usable in a confined space, where often only one free face is available. Many technicians and researchers agree that two technologies will probably open the door to underground quarrying in hard rocks: diamond wire and water jet. The first one is already available; the second should still be improved. The paper refers to some of the most important and significant examples in Italy, and underlines the possibility of extending, by underground quarrying, the exploitation of important and well-appreciated natural stones, as the quartzite-sandstone of the Tosco-Emiliano Appennini (Firenzuola Stone) and the Alpine gneisses. In order to pass from the simple experimental stage (explorative drift) to the more complex 3D design of the underground voids, detailed geo-structural reconstruction of the rock body and specific lithological in situ surveys are needed: such important aspects represent a very interesting common field between mining engineers and geologists.

78 FR 56125 - National Days of Prayer and Remembrance, 2013

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-11

... its core. Where two towers once cast a shadow, men and women gather in the early light to pay their... etched in white marble. At the Pentagon, where a single stone still bears the scars of fire, a Nation...

Infection (urease) stones.

PubMed

Griffith, D P; Osborne, C A

1987-01-01

Infection-induced stones in man probably form solely as a consequence of urealysis which is catalyzed by the bacterial protein urease. Urease stones composed of struvite and carbonate-apatite may form primarily, or as secondary stones or pre-existent metabolic stones. Struvite stones form and grow rapidly owing to (a) supersaturation of urine with stone forming salts, (b) 'salting out' of poorly soluble organic substances normally dissolved in urine and (c) ammonia-induced destruction of the normally protective urothelial glycosaminoglycan layer. Immature (predominantly organic) matrix stones mature into densely mineralized stones. Curative treatment is possible only by eliminating all of the stone and by eradicating all urinary and parenchymal infection. A variety of operative and pharmaceutical approaches are available. Patient treatment must be individualized inasmuch as some patients are better candidates for one type of treatment than another.

A multiple technique approach to the analysis of urinary calculi.

PubMed

Rodgers, A L; Nassimbeni, L R; Mulder, K J

1982-01-01

10 urinary calculi have been qualitatively and quantitatively analysed using X-ray diffraction, infra-red, scanning electron microscopy, X-ray fluorescence, atomic absorption and density gradient procedures. Constituents and compositional features which often go undetected due to limitations in the particular analytical procedure being used, have been identified and a detailed picture of each stone's composition and structure has been obtained. In all cases at least two components were detected suggesting that the multiple technique approach might cast some doubt as to the existence of "pure" stones. Evidence for a continuous, non-sequential deposition mechanism has been detected. In addition, the usefulness of each technique in the analysis of urinary stones has been assessed and the multiple technique approach has been evaluated as a whole.

Flores hominid: new species or microcephalic dwarf?

PubMed

Martin, Robert D; Maclarnon, Ann M; Phillips, James L; Dobyns, William B

2006-11-01

The proposed new hominid "Homo floresiensis" is based on specimens from cave deposits on the Indonesian island Flores. The primary evidence, dated at approximately 18,000 y, is a skull and partial skeleton of a very small but dentally adult individual (LB1). Incomplete specimens are attributed to eight additional individuals. Stone tools at the site are also attributed to H. floresiensis. The discoverers interpreted H. floresiensis as an insular dwarf derived from Homo erectus, but others see LB1 as a small-bodied microcephalic Homo sapiens. Study of virtual endocasts, including LB1 and a European microcephalic, purportedly excluded microcephaly, but reconsideration reveals several problems. The cranial capacity of LB1 ( approximately 400 cc) is smaller than in any other known hominid < 3.5 Ma and is far too small to derive from Homo erectus by normal dwarfing. By contrast, some associated tools were generated with a prepared-core technique previously unknown for H. erectus, including bladelets otherwise associated exclusively with H. sapiens. The single European microcephalic skull used in comparing virtual endocasts was particularly unsuitable. The specimen was a cast, not the original skull (traced to Stuttgart), from a 10-year-old child with massive pathology. Moreover, the calotte does not fit well with the rest of the cast, probably being a later addition of unknown history. Consideration of various forms of human microcephaly and of two adult specimens indicates that LB1 could well be a microcephalic Homo sapiens. This is the most likely explanation for the incongruous association of a small-brained recent hominid with advanced stone tools. (c) 2006 Wiley-Liss, Inc.

Self-organization of sorted patterned ground.

PubMed

Kessler, M A; Werner, B T

2003-01-17

Striking circular, labyrinthine, polygonal, and striped patterns of stones and soil self-organize in many polar and high alpine environments. These forms emerge because freeze-thaw cycles drive an interplay between two feedback mechanisms. First, formation of ice lenses in freezing soil sorts stones and soil by displacing soil toward soil-rich domains and stones toward stone-rich domains. Second, stones are transported along the axis of elongate stone domains, which are squeezed and confined as freezing soil domains expand. In a numerical model implementing these feedbacks, circles, labyrinths, and islands form when sorting dominates; polygonal networks form when stone domain squeezing and confinement dominate; and stripes form as hillslope gradient is increased.

Prehistoric human colonization of India.

PubMed

Misra, V N

2001-11-01

Human colonization in India encompasses a span of at least half-a-million years and is divided into two broad periods, namely the prehistoric (before the emergence of writing) and the historic (after writing). The prehistoric period is divided into stone, bronze and iron ages. The stone age is further divided into palaeolithic, mesolithic and neolithic periods. As the name suggests, the technology in these periods was primarily based on stone. Economically, the palaeolithic and mesolithic periods represented a nomadic, hunting-gathering way of life, while the neolithic period represented a settled, food-producing way of life. Subsequently copper was introduced as a new material and this period was designated as the chalcolithic period. The invention of agriculture, which took place about 8000 years ago, brought about dramatic changes in the economy, technology and demography of human societies. Human habitat in the hunting-gathering stage was essentially on hilly, rocky and forested regions, which had ample wild plant and animal food resources. The introduction of agriculture saw it shifting to the alluvial plains which had fertile soil and perennial availability of water. Hills and forests, which had so far been areas of attraction, now turned into areas of isolation. Agriculture led to the emergence of villages and towns and brought with it the division of society into occupational groups. The first urbanization took place during the bronze age in the arid and semi-arid region of northwest India in the valleys of the Indus and the Saraswati rivers, the latter represented by the now dry Ghaggar-Hakra bed. This urbanization is known as the Indus or Harappan civilization which flourished during 3500-1500 B.C. The rest of India during this period was inhabited by neolithic and chalcolithic farmers and mesolithic hunter-gatherers. With the introduction of iron technology about 3000 years ago, the focus of development shifted eastward into the Indo-Gangetic divide and the Ganga valley. The location of the Mahabharata epic, which is set in the beginning of the first millennium B.C., is the Indo-Gangetic divide and the upper Ganga-Yamuna doab (land between two rivers). Iron technology enabled pioneering farmers to clear the dense and tangled forests of the middle and lower Ganga plains. The focus of development now shifted further eastward to eastern Uttar Pradesh and western Bihar which witnessed the events of the Ramayana epic and rise of the first political entities known as Mahajanapadas as also of Buddhism and Jainism. The second phase of urbanization of India, marked by trade, coinage, script and birth of the first Indian empire, namely Magadha, with its capital at Pataliputra (modern Patna) also took place in this region in the sixth century B.C. The imposition by Brahmin priests of the concepts of racial and ritual purity, pollution, restrictions on sharing of food, endogamy, anuloma (male of upper caste eligible to marry a female of lower caste) and pratiloma (female of upper caste ineligible to marry a male of lower caste) forms of marriage, karma (reaping the fruits of the actions of previous life in the present life), rebirth, varnashrama dharma (four stages of the expected hundred-year life span) and the sixteen sanskaras (ceremonies) on traditional occupational groups led to the birth of the caste system - a unique Indian phenomenon. As a consequence of the expansion of agriculture and loss of forests and wildlife, stone age hunter-gatherers were forced to assimilate themselves into larger agriculture-based rural and urban societies. However, some of them resisted this new economic mode. To this day they have persisted with their atavistic lifestyle, but have had to supplement their resources by producing craft items or providing entertainment to the rural population.

Prospecting history leading to the discovery of Botswana's diamond mines: from artefacts to Lesedi La Rona

NASA Astrophysics Data System (ADS)

de Wit, Michiel C. J.

2018-02-01

Bechuanaland/Botswana has a long and colourful history in exploration and mining. Here these activities are subdivided into three phases: pre-historic, historic and modern. Quarrying stone in Botswana was ongoing 500,000 years ago during the Early Stone Age (ESA). Actual mining of stones probably only started during the Middle Stone Age (MSA) i.e. post 250,000 BP, and the first prehistoric hard rock mining of specularite and limonite, likely started during the Late Stone Age (LSA) 20,000 to 2,000 BP. In east Botswana iron and copper were mined from AD 800 onwards; the mining of gold started in the thirteenth century. Historic mining started with the re-discovery of gold close to Francistown in 1865 and lasted until the 1950s. Rumours of diamonds in Bechuanaland had already surfaced in the 1880s, and it was Ngamiland, in the northwest, that was first explored systematically for diamonds and gold between 1896 and 1899. A joint initiative between Anglo American and De Beers started serious prospecting parts of eastern Bechuanaland between 1932 and 1938; and in 1938 the first diamond finds in Bechuanaland were reported. Modern mining and exploration started with the signing of an agreement in 1959, allowing Consolidated African Selection Trust Ltd (CAST) into the Bamangwato Tribal Reserve. CAST found a few diamonds in the Motloutse River, but concluded that these were reworked and dropped the exploration rights. De Beers believed that these diamonds had come from west of the Motloutse headwaters, across the watershed in the Kalahari. This ultimately led to the discovery of the Orapa kimberlite field in 1967, a year after Botswana became independent. This discovery triggered a major exploration boom across Botswana adding important diamond-bearing kimberlites such as at Letlhakane (1968), Jwaneng (1973), Gope (1981) and Lerala (1991).

Histopathology Predicts the Mechanism of Stone Formation

NASA Astrophysics Data System (ADS)

Evan, Andrew P.

2007-04-01

About 5% of American women and 12% of men will develop a kidney stone at some time in their life and these numbers appear to be on the rise. Despite years of scientific research into the mechanisms of stone formation and growth, limited advances have been made until recently. Randall's original observations and thoughts on the mechanisms for kidney stone formation have been validated for idiopathic calcium oxalate stone formers (ICSF) but not for most other stone forming groups. Our current studies on selected groups of human stone formers using intraoperative papillary biopsies has shown overwhelming evidence for the presence of Randall's plaque in ICSF and that stone formation and growth are exclusively linked to its availability to urinary ions and proteins. Intense investigation of the plaque-stone junction is needed if we are to understand the factors leading to the overgrowth process on exposed regions of plaque. Such information should allow the development of treatment strategies to block stone formation in ICSF patients. Patients who form brushite stones, or who form apatite stones because of distal renal tubular acidosis (dRTA), or patients with calcium oxalate stones due to obesity bypass procedures, or patients with cystinuria, get plugged inner medullary collecting ducts (IMCD) which leads to total destruction of the lining cells and focal sites of interstitial fibrosis. These stone formers have plaque but at levels equal to or below non-stone formers, which would suggest that they form stones by a different mechanism than do ICSF patients.

Kidney pain (image)

MedlinePlus

A kidney stone is a solid piece of material that forms in a kidney. Kidney stones may be the size of sand or ... A kidney stone is a solid piece of material that forms in a kidney. Kidney stones may be the ...

Finite element analysis of steel fiber-reinforced concrete (SFRC): validation of experimental tensile capacity of dog-bone specimens

NASA Astrophysics Data System (ADS)

Islam, Md. Mashfiqul; Chowdhury, Md. Arman; Sayeed, Md. Abu; Hossain, Elsha Al; Ahmed, Sheikh Saleh; Siddique, Ashfia

2014-09-01

Finite element analyses are conducted to model the tensile capacity of steel fiber-reinforced concrete (SFRC). For this purpose dog-bone specimens are casted and tested under direct and uniaxial tension. Two types of aggregates (brick and stone) are used to cast the SFRC and plain concrete. The fiber volume ratio is maintained 1.5 %. Total 8 numbers of dog-bone specimens are made and tested in a 1000-kN capacity digital universal testing machine (UTM). The strain data are gathered employing digital image correlation technique from high-definition images and high-speed video clips. Then, the strain data are synthesized with the load data obtained from the load cell of the UTM. The tensile capacity enhancement is found 182-253 % compared to control specimen to brick SFRC and in case of stone SFRC the enhancement is 157-268 %. Fibers are found to enhance the tensile capacity as well as ductile properties of concrete that ensures to prevent sudden brittle failure. The dog-bone specimens are modeled in the ANSYS 10.0 finite element platform and analyzed to model the tensile capacity of brick and stone SFRC. The SOLID65 element is used to model the SFRC as well as plain concretes by optimizing the Poisson's ratio, modulus of elasticity, tensile strength and stress-strain relationships and also failure pattern as well as failure locations. This research provides information of the tensile capacity enhancement of SFRC made of both brick and stone which will be helpful for the construction industry of Bangladesh to introduce this engineering material in earthquake design. Last of all, the finite element outputs are found to hold good agreement with the experimental tensile capacity which validates the FE modeling.

Evaluation of impression accuracy for a four-implant mandibular model--a digital approach.

PubMed

Stimmelmayr, Michael; Erdelt, Kurt; Güth, Jan-Frederik; Happe, Arndt; Beuer, Florian

2012-08-01

Implant-supported prosthodontics requires precise impressions to achieve a passive fit. Since the early 1990s, in vitro studies comparing different implant impression techniques were performed, capturing the data mostly mechanically. The purpose of this study was to evaluate the accuracy of three different impression techniques digitally. Dental implants were inserted bilaterally in ten polymer lower-arch models at the positions of the first molars and canines. From each original model, three different impressions (A, transfer; B, pick-up; and C, splinted pick-up) were taken. Scan-bodies were mounted on the implants of the polymer and on the lab analogues of the stone models and digitized. The scan-body in position 36 (FDI) of the digitized original and master casts were each superimposed, and the deviations of the remaining three scan-bodies were measured three-dimensionally. The systematic error of digitizing the models was 13 μm for the polymer and 5 μm for the stone model. The mean discrepancies of the original model to the stone casts were 124 μm (±34) μm for the transfer technique, 116 (±46) μm for the pick-up technique, and 80 (±25) μm for the splinted pick-up technique. There were statistically significant discrepancies between the evaluated impression techniques (p ≤ 0.025; ANOVA test). The splinted pick-up impression showed the least deviation between original and stone model; transfer and pick-up techniques showed similar results. For better accuracy of implant-supported prosthodontics, the splinted pick-up technique should be used for impressions of four implants evenly spread in edentulous jaws.

Accuracy of impressions with different impression materials in angulated implants.

PubMed

Reddy, S; Prasad, K; Vakil, H; Jain, A; Chowdhary, R

2013-01-01

To evaluate the dimensional accuracy of the resultant (duplicative) casts made from two different impression materials (polyvinyl siloxane and polyether) in parallel and angulated implants. Three definitive master casts (control groups) were fabricated in dental stone with three implants, placed at equi-distance. In first group (control), all three implants were placed parallel to each other and perpendicular to the plane of the cast. In the second and third group (control), all three implants were placed at 10° and 15 o angulation respectively to the long axis of the cast, tilting towards the centre. Impressions were made with polyvinyl siloxane and polyether impression materials in a special tray, using a open tray impression technique from the master casts. These impressions were poured to obtain test casts. Three reference distances were evaluated on each test cast by using a profile projector and compared with control groups to determine the effect of combined interaction of implant angulation and impression materials on the accuracy of implant resultant cast. Statistical analysis revealed no significant difference in dimensional accuracy of the resultant casts made from two different impression materials (polyvinyl siloxane and polyether) by closed tray impression technique in parallel and angulated implants. On the basis of the results of this study, the use of both the impression materials i.e., polyether and polyvinyl siloxane impression is recommended for impression making in parallel as well as angulated implants.

Biochemical profile of stone-forming patients with diabetes mellitus.

PubMed

Pak, Charles Y C; Sakhaee, Khashayar; Moe, Orson; Preminger, Glenn M; Poindexter, John R; Peterson, Roy D; Pietrow, Paul; Ekeruo, Wesley

2003-03-01

To test the hypothesis that stone-forming patients with type II diabetes (DM-II) have a high prevalence of uric acid (UA) stones and present with some of the biochemical features of gouty diathesis (GD). The demographic and initial biochemical data from 59 stone-forming patients with DM-II (serum glucose greater than 126 mg/dL, no insulin therapy, older than 35 years of age) from Dallas, Texas and Durham, North Carolina were retrieved and compared with data from 58 patients with GD and 116 with hyperuricosuric calcium oxalate urolithiasis (HUCU) without DM. UA stones were detected in 33.9% of patients with DM-II compared with 6.2% of stone-forming patients without DM (P <0.001). Despite similar ingestion of alkali, the urinary pH in patients with DM-II and UA stones (n = 20) was low (pH = 5.5), as it is in patients with GD, and was significantly lower than in patients with HUCU. The urinary pH in patients with DM-II and calcium stones (n = 39) was intermediate between that in those with DM-II and UA stones and those with HUCU. However, both DM groups had fractional excretion of urate that was not depressed, as it is in those with GD, and was comparable to the value obtained in those with HUCU. The urinary content of undissociated UA was significantly higher, and the saturation of calcium phosphate (brushite) and sodium urate was significantly lower in those with DM-II and UA stones than in those with HUCU. Stone-forming patients with DM-II have a high prevalence of UA stones. Diabetic patients with UA stones share a key feature of those with GD, namely the passage of unusually acid urine, but not the low fractional excretion of urate.

Assessing applicants to the NASA flight program for their renal stone-forming potential

NASA Technical Reports Server (NTRS)

Pak, Charles Y. C.; Hill, Kathy; Cintron, Nitza M.; Huntoon, Carolyn

1989-01-01

Because spaceflight can provoke the formation of kidney stones, 24-hour urine samples for 104 male applicants were analyzed for stone-forming risk factors prior to their selection into the NASA astronaut-mission specialist corps. A high level of supersaturation (with either calcium oxalate, brushite, or monosodium urate) was noted in these applicants which predisposes them to the crystallization of stone-forming calcium salts. It is suggested that most of the abnormal stone risk factors found were environmental, rather than metabolic, in origin.

Harry Potter Casts His Spell in the Classroom

ERIC Educational Resources Information Center

Witschonke, Christopher

2006-01-01

This article deals with the use of alternative texts, such as the Harry Potter book series in classroom teaching. In this article, the author discusses a wide range of themes that could be addressed in the classroom. Harry Potter and the Sorcerer's Stone deals with issues of greed, self-sacrifice, fear of the unknown, and self-confidence. Harry…

Bryce Canyon National Park: Hoodoos Cast Their Spell. Teaching with Historic Places.

ERIC Educational Resources Information Center

Shakespear, Mala

Surrounded by the beauty of southern Utah and panoramic views of three states, filigrees of colorful stones that erosion has shaped into a spectacular array of spires, fins, and pinnacles called "hoodoos" remind tourist viewers of church steeples, Gothic spires, castle walls, animals, and even people. In this lesson students explore why…

Risk factors for pancreatic stone formation in autoimmune pancreatitis over a long-term course.

PubMed

Maruyama, Masahiro; Arakura, Norikazu; Ozaki, Yayoi; Watanabe, Takayuki; Ito, Tetsuya; Yoneda, Suguru; Maruyama, Masafumi; Muraki, Takashi; Hamano, Hideaki; Matsumoto, Akihiro; Kawa, Shigeyuki

2012-05-01

Autoimmune pancreatitis (AIP) has the potential to progress to a chronic state that forms pancreatic stones. The aim of this study was to clarify the risk factors underlying pancreatic stone formation in AIP. Sixty-nine patients with AIP who had been followed for at least 3 years were enrolled for evaluation of clinical and laboratory factors as well as computed tomography and endoscopic retrograde cholangiopancreatography findings. During the course of this study, increased or de novo stone formation was seen in 28 patients, who were defined as the stone-forming group. No stones were observed in 32 patients, who were defined as the non-stone-forming group. Nine patients who had stones at diagnosis but showed no change during the course of this study were excluded from our cohort. Univariate analysis revealed no significant differences in clinical or laboratory factors associated with AIP-specific inflammation between the two groups. However, pancreatic head swelling (P = 0.006) and narrowing of both Wirsung's and Santorini's ducts in the pancreatic head region (P = 0.010) were significantly more frequent in the stone-forming group. Furthermore, multivariate analysis identified Wirsung and Santorini duct narrowing at diagnosis as a significant independent risk factor for pancreatic stone formation (OR 4.4, P = 0.019). A primary risk factor for pancreatic stone formation in AIP was narrowing of both Wirsung's and Santorini's ducts, which most presumably led to pancreatic juice stasis and stone development.

Distortion of three-unit implant frameworks during casting, soldering, and simulated porcelain firings.

PubMed

Zervas, P J; Papazoglou, E; Beck, F M; Carr, A B

1999-09-01

The aim of this study was to assess distortion inherent in casting, soldering, and simulated porcelain firings of screw-retained, implant-supported three-unit fixed partial dentures (FPDs). Ten wax patterns were fabricated on a die-stone cast containing two implants, 20 mm apart from center to center. Five specimens were cast in a high-palladium alloy, exposed to simulated porcelain firings, sectioned, and then soldered with low-fusing solder. Five specimens were cast, sectioned, soldered with high-fusing solder, and then exposed to simulated porcelain firings. For each specimen, two horizontal and six vertical distances between appropriately scribed reference points were measured with a traveling microscope. Comparisons were made among the various measurements taken after wax-pattern fabrication, casting, high- and low-fusing soldering, and each porcelain firing. Data were analyzed using a repeated-measures factorial ANOVA (alpha = 0.05). Significant difference was detected in the amount of horizontal distortion during casting (53 +/- 24 microns) and high-fusing soldering (-49 +/- 50 microns), as well as in the amount of horizontal distortion during high-fusing soldering (-49 +/- 50 microns) and low-fusing soldering (17 +/- 26 microns). However, no clinically significant difference was found in the amount of horizontal distortion during casting, low-fusing, and high-fusing soldering. The greatest amount of distortion during the simulated porcelain firings took place during the oxidizing cycle. Soldering did not improve the casting misfit of a three-unit implant-retained FPD model. Metal-ceramic implant frameworks should be oxidized before intraoral fit evaluation.

Kidney Stones (For Parents)

MedlinePlus

... Staying Safe Videos for Educators Search English Español Kidney Stones KidsHealth / For Parents / Kidney Stones What's in ... other treatments to help remove the stones. How Kidney Stones Form It's the kidneys' job to remove ...

Accuracy of ringless casting and accelerated wax-elimination technique: a comparative in vitro study.

PubMed

Prasad, Rahul; Al-Keraif, Abdulaziz Abdullah; Kathuria, Nidhi; Gandhi, P V; Bhide, S V

2014-02-01

The purpose of this study was to determine whether the ringless casting and accelerated wax-elimination techniques can be combined to offer a cost-effective, clinically acceptable, and time-saving alternative for fabricating single unit castings in fixed prosthodontics. Sixty standardized wax copings were fabricated on a type IV stone replica of a stainless steel die. The wax patterns were divided into four groups. The first group was cast using the ringless investment technique and conventional wax-elimination method; the second group was cast using the ringless investment technique and accelerated wax-elimination method; the third group was cast using the conventional metal ring investment technique and conventional wax-elimination method; the fourth group was cast using the metal ring investment technique and accelerated wax-elimination method. The vertical marginal gap was measured at four sites per specimen, using a digital optical microscope at 100× magnification. The results were analyzed using two-way ANOVA to determine statistical significance. The vertical marginal gaps of castings fabricated using the ringless technique (76.98 ± 7.59 μm) were significantly less (p < 0.05) than those castings fabricated using the conventional metal ring technique (138.44 ± 28.59 μm); however, the vertical marginal gaps of the conventional (102.63 ± 36.12 μm) and accelerated wax-elimination (112.79 ± 38.34 μm) castings were not statistically significant (p > 0.05). The ringless investment technique can produce castings with higher accuracy and can be favorably combined with the accelerated wax-elimination method as a vital alternative to the time-consuming conventional technique of casting restorations in fixed prosthodontics. © 2013 by the American College of Prosthodontists.

Sedimentary rocks in our mouth: dental pulp stones made by nanobacteria

NASA Astrophysics Data System (ADS)

Ciftcioglu, Neva; Ciftcioglu, Vefa; Vali, Hojatollah; Turcott, Eduardo; Kajander, E. Olavi

1998-07-01

The mechanisms of dental pulp stone formation are still largely unknown. Pulp stones are mainly composed of carbonate apatite. Only few experimental reports have elucidated the potential of some selected bacteria to produce apatite under in vitro conditions using special calcification media. The tested stone forming bacteria were, in fact, often better known for their cariogenic potential. Our preliminary work with 18 dental pulp stones from Turkey, selected only by severity of the stone formation, indicated the presence of nanobacterial antigens in the demineralized stones. Furthermore, high incidence of kidney stones and gall stones in the patient group and in their parents was found. This raises the implication that nanobacteria may enter the body also via oral route, in addition to the parenteral and transplacental routes. The role of nanobacteria in dental pulp stone formation was further studied by following nanobacterial colonization and mineral formation on human tooth in vitro. Two molar teeth, one having pulp stone and one without, were vertically cut into two pieces, sterilized by autoclaving and incubated with or without nanobacteria in DMEM. Electron microscopic observations indicate that nanobacteria can cause apatite stone formation on tooth surface. The sever from of dental pulp stone formation might be associated with nanobacteria. This form of dental disease results in loss of teeth due to osteolytic processes. This addresses the necessity for a study on unconventional mineral-forming bacteria as a cause for human diseases.

Cavitation Bubble Cluster Activity in the Breakage of Kidney Stones by Lithotripter Shock Waves

PubMed Central

Pishchalnikov, Yuriy A.; Sapozhnikov, Oleg A.; Bailey, Michael R.; Williams, James C.; Cleveland, Robin O.; Colonius, Tim; Crum, Lawrence A.; Evan, Andrew P.; McAteer, James A.

2008-01-01

High-speed photography was used to analyze cavitation bubble activity at the surface of artificial and natural kidney stones during exposure to lithotripter shock waves in vitro. Numerous individual bubbles formed at the surface of stones, but these bubbles did not remain independent and combined with one another to form bubble clusters. Bubble clusters formed at the proximal end, the distal end, and at the sides of stones. Each cluster collapsed to a narrow point of impact. Collapse of the proximal cluster caused erosion at the leading face of the stone and the collapse of clusters at the sides of stones appeared to contribute to the growth of cracks. Collapse of the distal cluster caused minimal damage. We conclude that cavitation-mediated damage to stones was due not to the action of solitary bubbles, but to the growth and collapse of bubble clusters. PMID:14565872

Kidney stones during pregnancy: an investigation into stone composition.

PubMed

Ross, Ashley E; Handa, Shelly; Lingeman, James E; Matlaga, Brian R

2008-05-01

Kidney stones can be a source of considerable morbidity for pregnant women. Although there is a body of literature confirming that different stone compositions predominate for different age and sex cohorts, there have been no similar reports characterizing the nature of stone disease during pregnancy. We performed a multi-institutional study to define the composition of renal calculi diagnosed during pregnancy. We retrospectively reviewed the records from two stone referral centers of all patients diagnosed with a de novo kidney stone during pregnancy who underwent a procedure for the purpose of stone removal from June 2001 through September 2007. A total of 27 patients were identified, with a mean age of 26.8 years (range, 21-34). Twenty patients (74%) had no history of prior stone formation. Seven patients (26%) had previously formed stones, although none of these patients had a known kidney stone at the time they became pregnant. Stones were removed in the first, second, third trimester and immediately post-partum in 4, 52, 22, and 22% respectively. Stone removal was performed without complication in all cases. Analysis found that in 74% of all cases (20 patients) stones were composed predominantly of calcium phosphate (hydroxyapatite). In 26% of cases, (7 patients) the stones were composed predominantly of calcium oxalate. Of the seven patients with prior stone history, three patients had previously formed calcium phosphate stones and four patients had previously formed calcium oxalate stones. Calcium oxalate calculi are the most common stone in non-pregnant women of a comparable age as our subjects. However, our present data suggest that stones detected during pregnancy are most commonly composed of calcium phosphate (hydroxyapatite). Indeed, it is the minority of stones that are composed of calcium oxalate. Although the reason for this unusual preponderance of calcium phosphate calculi is unclear, physiologic alterations that occur during pregnancy may be influential.

Improved digital transfer of the maxillary cast to a virtual articulator.

PubMed

Solaberrieta, Eneko; Otegi, Jose Ramon; Mínguez, Rikardo; Etxaniz, Olatz

2014-10-01

The clinical procedure described provides a quantifiable, repeatable, and reliable method of transferring the location of the maxillary dental arch from the patient directly to a virtual articulator (virtual facebow transfer) by means of reverse engineering devices to design a customized dental restoration. This procedure allows the dentist and the dental laboratory technician to work in a fully digital environment without having to mount stone casts on a mechanical articulator. In addition, specific suggestions are provided for designing the transfer device to enhance patient comfort during the data transfer process and reduce deviation. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

The utilization of stone ash on cellular lightweight concrete

NASA Astrophysics Data System (ADS)

Karolina, R.; Sianipar, Y. G. C.

2018-02-01

Lightweight concrete brick is a brick which made of cement, sand, water, and foam as the basic composition. This brick are divided into 2, based on the foam used such as AAC (Autoclave Aerated Concrete) that use aluminium paste and CLC(Cellular Lightweight Concrete) that use foaming agent from BASF as its foaming material. In this trial, the lightweight brick that are ging to be use are the CLC with foaming agent as its foaming material with the mixture of stone ash that are produced by the Stone Crusher with spesific gravity 2666 kg/m3 as their partly sand substitution . In this research, the stone ash variant that are used are 10%, 15%, and 20% from the amount of sand that planned before. After casting, the result of the 10% will receive a reduction of compressive strength while an increasing in absorption as 25.07% and 39.005% and the 15% variant will recieve a reduction of compressive strength as much as 65.8% and a reduction of absorption as much as 17.441% and the 20% variant will recieve a reduction of compressive strength as much as 67.4% while an increasing of absorption as much as 17.956%.

Radionuclide and contaminant immobilization in the fluidized bed steam reforming waste products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neeway, James J.; Qafoku, Nikolla; Westsik, Joseph H.

2012-05-01

The goal of this chapter is to introduce the reader to the Fluidized Bed Steam Reforming (FBSR) process and resulting waste form. The first section of the chapter gives an overview of the potential need for FBSR processing in nuclear waste remediation followed by an overview of the engineering involved in the process itself. This is followed by a description of waste form production at a chemical level followed by a section describing different process streams that have undergone the FBSR process. The third section describes the resulting mineral product in terms of phases that are present and the abilitymore » of the waste form to encapsulate hazardous and radioactive wastes from several sources. Following this description is a presentation of the physical properties of the granular and monolith waste form product including and contaminant release mechanisms. The last section gives a brief summary of this chapter and includes a section on the strengths associated with this waste form and the needs for additional data and remaining questions yet to be answered. The reader is directed elsewhere for more information on other waste forms such as Cast Stone (Lockrem, 2005), Ceramicrete (Singh et al., 1997, Wagh et al., 1999) and geopolymers (Kyritsis et al., 2009; Russell et al., 2006).« less

An Information Framework for Facility Operators

DTIC Science & Technology

1991-01-01

and replacement products. Type: Type is used to decompose the building into smaller categories called arrangements, assemblies, parts, joints , and forro...are organized into crews and shops consisting of tradepersons responsible for building materials (concrete, masonry, metals, drywall , paint, etc...Comp Type (pre-cast, CIP) AS I Curing compound , sealant tyDe A S 04--- Masonry Comp Type (CMU, stone, glazed) A S I Manufacturer, style no., color no

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serne, R. Jeffrey; Lanigan, David C.; Westsik, Joseph H.

This revision to the original report adds two longer term leach sets of data to the report and provides more discussion and graphics on how to interpret the results from long-term laboratory leach tests. The leach tests were performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to evaluate the release of key constituents from monoliths of Cast Stone prepared with four simulated low-activity waste (LAW) liquid waste streams.

Fit of cobalt–chromium implant frameworks before and after ceramic veneering in comparison with CNC‐milled titanium frameworks

PubMed Central

Svanborg, Per; Eliasson, Alf

2015-01-01

Abstract Computer‐aided design/computer‐aided manufacturing fabrication of implant‐supported frameworks is a standard procedure, and the use of ceramic‐veneered cobalt–chromium alloys is increasing. However, no data are available concerning the precision of fit of these frameworks and the impact on the fit of the veneering procedure. The aim of this study was to evaluate the fit of computer numeric‐controlled‐milled cobalt–chromium and titanium implant frameworks for edentulous maxillas, provided with six implants. An additional aim was to evaluate the effect of ceramic veneering on the fit of the cobalt–chromium frameworks. Ten stone casts simulating an edentulous maxilla provided with six dental implants and abutments were produced. One computer numeric‐controlled‐milled cobalt–chromium framework and one titanium framework were fabricated for each stone cast. Each stone cast and corresponding titanium and cobalt–chromium framework was measured with a coordinate measuring machine in the three‐dimensional (X axis, Y axis, and Z axis) directions. Both milled titanium and cobalt–chromium frameworks presented a good fit in the vertical plane (Z axis), 5.3 µm for titanium frameworks and 4.6 µm for the cobalt–chromium frameworks. The titanium frameworks showed a statistically significant smaller mean degree of misfit in the horizontal plane, X (5.0 µm) and Y (2.8 µm) axes as compared with the cobalt–chromium frameworks presenting a mean deviation of 13.5 µm in X axis and 6.3 µm in Y axis (P < 0.001). After ceramic veneering of the cobalt–chromium frameworks, the horizontal distortion significantly decreased from 13.5 to 9.7 µm in X axis (P = 0.007) and from 6.3 to 4.4 µm in Y axis (P = 0.017). The fit of both titanium and cobalt–chromium frameworks was very good. There were small but significant differences in fit between the titanium and cobalt–chromium frameworks, but the difference is of no clinical significance. The ceramic veneering resulted in a minor but significant improvement of the fit for the cobalt–chromium frameworks. PMID:29744140

Hypersecretion of mucus glycoprotein by the gallbladder epithelium in experimental cholelithiasis.

PubMed

Lee, S P

1981-07-01

In three models of cholelithiasis (dihydrocholesterol-fed rabbits, cholesterol-cholic acid-fed mice, and Lincomycin-treated guinea pigs), the quantity and chemical composition of gallbladder epithelial mucin have been studied using (1) a spectrum of histochemical glycoprotein stains, and (2) biochemical extraction, purification and analysis of the carbohydrate components of epithelial mucin. Despite the diverse mechanism of stone induction and difference in stone composition, a common pattern of response by the epithelial mucin was observed in all three models. There was a quantitative increase in epithelial mucus production at a time before stones were formed and this increase persisted till stones were formed. There was no difference, qualitatively, between mucus produced by normal and stone-forming gallbladders.

Effect of dental technician disparities on the 3-dimensional accuracy of definitive casts.

PubMed

Emir, Faruk; Piskin, Bulent; Sipahi, Cumhur

2017-03-01

Studies that evaluated the effect of dental technician disparities on the accuracy of presectioned and postsectioned definitive casts are lacking. The purpose of this in vitro study was to evaluate the accuracy of presectioned and postsectioned definitive casts fabricated by different dental technicians by using a 3-dimensional computer-aided measurement method. An arch-shaped metal master model consisting of 5 abutments resembling prepared mandibular incisors, canines, and first molars and with a 6-degree total angle of convergence was designed and fabricated by computer-aided design and computer-aided manufacturing (CAD-CAM) technology. Complete arch impressions were made (N=110) from the master model, using polyvinyl siloxane (PVS) and delivered to 11 dental technicians. Each technician fabricated 10 definitive casts with dental stone, and the obtained casts were numbered. All casts were sectioned, and removable dies were obtained. The master model and the presectioned and postsectioned definitive casts were digitized with an extraoral scanner, and the virtual master model and virtual presectioned and postsectioned definitive casts were obtained. All definitive casts were compared with the master model by using computer-aided measurements, and the 3-dimensional accuracy of the definitive casts was determined with best fit alignment and represented in color-coded maps. Differences were analyzed using univariate analyses of variance, and the Tukey honest significant differences post hoc tests were used for multiple comparisons (α=.05). The accuracy of presectioned and postsectioned definitive casts was significantly affected by dental technician disparities (P<.001). The largest dimensional changes were detected in the anterior abutments of both of the definitive casts. The changes mostly occurred in the mesiodistal dimension (P<.001). Within the limitations of this in vitro study, the accuracy of presectioned and postsectioned definitive casts is susceptible to dental technician differences. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Treatment of the Infected Stone.

PubMed

Marien, Tracy; Miller, Nicole L

2015-11-01

Infected kidney stones refer to stones that form because of urinary tract infections with urease-producing bacteria, secondarily infected stones of any composition, or stones obstructing the urinary tract leading to pyelonephritis. The mainstay of treatment of infection stones is complete stone removal. Kidney stones that obstruct the urinary tract and cause obstructive pyelonephritis are also frequently referred to as infected stones. Obstructive pyelonephritis is a urologic emergency as it can result in sepsis and even death. Infection stones and obstructive stones causing pyelonephritis are different disease processes, and their workup and management are described separately. Copyright © 2015 Elsevier Inc. All rights reserved.

Protecting Space Travelers from Kidney Stones: Renal Stone Risk During Space Flight

NASA Technical Reports Server (NTRS)

Whitson, Peggy; Bloomberg, Jacob; Lee, Angie (Technical Monitor)

2002-01-01

Renal stones, popularly known as kidney or bladder stones, are small rock-like objects formed in the kidneys or urinary tract by deposits of calcium and other minerals. The problem arises when the stones block the drainage of the kidney, resulting in urinary obstruction and pain. Passing these stones can be one of the most painful experiences a person will endure so doctors often prescribe pain relievers to ease the experience. Drinking plenty of fluids, which help flush waste out of the body, and eating a well-balanced diet are the first steps to preventing stones. For individuals at risk, this may not be enough, and a doctor may recommend a special diet and medications. Unfortunately, approximately 60 percent of people who have had a renal stone will experience a recurrence. This is particularly true of men, who are four to five times more likely to develop stones than women. Renal stones do not discriminate based on age; even children are at risk. Astronauts are particularly at risk of developing renal stones because they lose bone and muscle mass; calcium, other minerals, and protein normally used for bone and muscle end up in the bloodstream and then in the kidneys. Without plenty of fluid to wash them away, crystals can form and then grow into stones. This factor compounds the risk for astronauts, since they also perceive that they are less thirsty in space and will drink less than normal during the mission. To minimize all of these factors, doctors must instead treat the stone-forming compounds with medication. This study will use potassium citrate to reduce the risk of stone formation. Renal stones are never convenient, but they are a particular concern for astronauts who have limited access to treatment during flight. Researchers are examining how earthbound preventions for renal stone formation work in flight, ensuring missions are not ended prematurely due to this medical condition. During STS-107, earthbound preventions and treatments become astronauts' gain.

Dimensional accuracy of jaw scans performed on alginate impressions or stone models: A practice-oriented study.

PubMed

Vogel, Annike B; Kilic, Fatih; Schmidt, Falko; Rübel, Sebastian; Lapatki, Bernd G

2015-07-01

Digital jaw models offer more extensive possibilities for analysis than casts and make it easier to share and archive relevant information. The aim of this study was to compare the dimensional accuracy of scans performed on alginate impressions and on stone models to reference scans performed on underlying resin models. Precision spheres 5 mm in diameter were occlusally fitted to the sites of the first premolars and first molars on a pair of jaw models fabricated from resin. A structured-light scanner was used for digitization. Once the two reference models had been scanned, alginate impressions were taken and scanned after no later than 1 h. A third series of scans was performed on type III stone models derived from the impressions. All scans were analyzed by performing five repeated measurements to determine the distances between the various sphere centers. Compared to the reference scans, the stone-model scans were larger by a mean of 73.6 µm (maxilla) or 65.2 µm (mandible). The impression scans were only larger by 7.7 µm (maxilla) or smaller by 0.7 µm (mandible). Median standard deviations over the five repeated measurements of 1.0 µm for the reference scans, 2.35 µm for the impression scans, and 2.0 µm for the stone-model scans indicate that the values measured in this study were adequately reproducible. Alginate impressions can be suitably digitized by structured-light scanning and offer considerably better dimensional accuracy than stone models. Apparently, however, both impression scans and stone-model scans can offer adequate precision for orthodontic purposes. The main issue of impression scans (which is incomplete representation of model surfaces) is being systematically explored in a follow-up study.

Of stones and monkeys: testing ecological constraints on stone handling, a behavioral tradition in Japanese macaques.

PubMed

Leca, Jean-Baptiste; Gunst, Noëlle; Huffman, Michael A

2008-02-01

Japanese macaques are known to manipulate stones by displaying various seemingly functionless behavioral patterns, including carrying a stone, rubbing two stones together, or gathering several stones into a pile. This form of solitary object play called stone handling (SH) is a behavioral tradition in Japanese macaques, showing striking intertroop differences in frequency and form. Here, we evaluated two ecologically based hypotheses invoked to account for these differences. We hypothesized that the occurrence and form of SH would be affected by stone availability and the degree of terrestriality. We used standardized sampling methods to assess differences in SH and terrestriality among four captive and six free-ranging troops of Japanese macaques, and determine site-specific stone availability. Although we demonstrated that SH is almost exclusively a terrestrial activity, our comparative analyses showed that the number of stones readily available and the relative amount of time spent on the ground by the macaques were not associated with the intertroop differences in the occurrence of SH. Failure to accept the terrestriality and stone availability hypotheses suggests that the performance of SH and the motivation to engage in this activity are both more diverse and more complex than the direct links to time spent on the ground or the number of stones locally available. Other environmental influences and sociodemographic factors should be jointly considered to identify the sources of variation in SH, as a beginning to better understand the constraints on the appearance and subsequent diffusion of stone-use traditions in nonhuman primates. Am J Phys Anthropol, 2008. (c) 2007 Wiley-Liss, Inc. Copyright 2007 Wiley-Liss, Inc.

Comparison of the passivity between cast alloy and laser-welded titanium overdenture bars.

PubMed

Paiva, Jose; Givan, Daniel A; Broome, James C; Lemons, Jack E; McCracken, Michael S

2009-12-01

The purpose of this study was to investigate the fit of cast alloy overdenture and laser-welded titanium-alloy bars by measuring induced strain upon tightening of the bars on a master cast as well as a function of screw tightening sequence. Four implant analogs were secured into Type IV dental stone to simulate a mandibular edentulous patient cast, and two groups of four overdenture bars were fabricated. Group I was four cast alloy bars and Group II was four laser-welded titanium bars. The cast alloy bars included Au-Ag-Pd, Pd-Ag-Au, Au-Ag-Cu-Pd, and Ag-Pd-Cu-Au, while the laser-welded bars were all Ti-Al-V alloy. Bars were made from the same master cast, were torqued into place, and the total strain in the bars was measured through five strain gauges bonded to the bar between the implants. Each bar was placed and torqued 27 times to 30 Ncm per screw using three tightening sequences. Data were processed through a strain amplifier and analyzed by computer using StrainSmart software. Data were analyzed by ANOVA and Tukey's post hoc test. Significant differences were found between alloy types. Laser-welded titanium bars tended to have lower strains than corresponding cast bars, although the Au-Ag-Pd bar was not significantly different. The magnitudes of total strain were the least when first tightening the ends of the bar. The passivity of implant overdenture bars was evaluated using total strain of the bar when tightening. Selecting a high modulus of elasticity cast alloy or use of laser-welded bar design resulted in the lowest average strain magnitudes. While the effect of screw tightening sequence was minimal, tightening the distal ends first demonstrated the lowest strain, and hence the best passivity.

Gender please, without the gender police: rethinking pain in archetypal narratives of butch, transgender, and FTM masculinity.

PubMed

Detloff, Madelyn

2006-01-01

Why is it that many of the often-cited narratives about butch, FTM, and/or transgender masculinity happen to be fictions that highlight suffering as a de facto rite of passage for the butch, FTM, or transgendered protagonist? This essay attempts to answer that question, first by outlining the "coherentist assumptions" of lesbian feminism and the forms of gender-policing that cast butch, FTM, and transgendered subjectivities as "false consciousness." It then analyzes the practice of anchoring butch, FTM, and/or transgender identity claims in pain-filled narratives such as "The Well of Loneliness," "Stone Butch Blues," and "Boys Don't Cry." While these narratives do important cultural work-exposing the violence heaped upon butches, FTMs, and transgendered guys-it may be time to imagine alternative narratives that are less invested in suffering as a barometer of masculine authenticity.

Comparative Evaluation of Tensile Strength in Die Stone Incorporated with Sodium and Calcium Hypochlorite as Disinfectants: An in vitro Study.

PubMed

Pramodh, N R; Kumar, C N Vijay; Pradeep, M R; Naik, Ravi; Mahesh, C S; Kumari, Manju R

2017-12-01

The aim of this study was to evaluate the tensile strength of die stone incorporated with sodium and calcium hypochlorite as disinfectants. Two commercially available type IV die stone (Kalrock: Kalabhai Karson Pvt., Ltd and Pearlstone: Asian Chemicals) and two commercially available disinfectant solutions (sodium hypochlorite and calcium hypochlorite: Beachem Laboratory Chemical Private Limited, Chennai and Leo Chem Private Limited, Bengaluru) were used in this study, and the tensile strength was measured using Lloyd's Universal Testing Machine. The results show that incorporating the disinfecting solutions decreases the tensile strength of both products. The effect of decreasing tensile strength on type IV gypsum product is seen more in calcium hypochlorite when compared with sodium hypochlorite disinfecting solution, and the tensile strength of Kalrock specimens is higher than Pearlstone specimens after disinfecting with sodium hypochlorite and calcium hypochlorite solution. The statistical results also show significant results in all the groups when compared with the control group. The incorporation of sodium and calcium hypochlorite disinfecting solutions is not an encouraging method for both die materials as it reduces the tensile strength of type IV gypsum product. Tensile strength of Kalstone® die material is superior than Pearlstone® die material after mixing with sodium hypochlorite and calcium hypochlorite. According to the recommendations of Americans with Disability Act (ADA) and the Centers for Disease Control and Prevention, disinfecting the whole cast without or minimal changes in physical and mechanical properties was the motto of the study. The tensile strength in type IV gypsum product plays a most important role in retrieval of cast from impression, especially in narrow tooth preparation. This study reveals that incorporating method of disinfecting solutions is not recommended as it reduces the tensile strength.

Assessment of a Modified Acoustic Lens for Electromagnetic Shock Wave Lithotripters in a Swine Model

PubMed Central

Mancini, John G.; Neisius, Andreas; Smith, Nathan; Sankin, Georgy; Astroza, Gaston M.; Lipkin, Michael E.; Simmons, Walther N.; Preminger, Glenn M.; Zhong, Pei

2013-01-01

Purpose The acoustic lens of the Siemens Modularis electromagnetic (EM) shock wave lithotripter has been modified to produce a pressure waveform and focal zone more closely resembling that of the original Dornier HM3 device. Herein, we assess the newly designed acoustic lens in vivo in an animal model. Materials and Methods Stone fragmentation and tissue injury produced by the original and modified lenses of a Siemens lithotripter were evaluated in a swine model under equivalent acoustic pulse energy (~45 mJ) at 1 Hz pulse repetition frequency. Stone fragmentation was determined by the weight percent of stone fragments less than 2 mm. For tissue injury assessment, shock wave-treated kidneys were perfused, dehydrated, cast in paraffin wax and sectioned. Digital images were captured every 120 µm and processed to determine the functional renal volume damage. Results After 500 shocks, stone fragmentation efficiency produced by the original and modified lenses was 48 ± 12% and 52 ± 17% (p=0.60), respectively. However, after 2000 shocks, the modified lens showed significantly improved stone fragmentation of 86 ± 10%, compared to 72 ± 12% for the original lens (p=0.02). Tissue injury caused by the original and modified lenses was minimal at 0.57 ± 0.44% and 0.25 ± 0.25% (p=0.27), respectively. Conclusions With lens modification, the Siemens Modularis lithotripter demonstrates significantly improved stone fragmentation with minimal tissue injury at clinically relevant acoustic pulse energy. This new lens design could potentially be retrofitted to existing lithotripters, thereby improving the effectiveness of EM lithotripters. PMID:23485509

Neponset River Basin Massachusetts, Flood Plain Management Study.

DTIC Science & Technology

1982-03-01

extensive water power. There are in the southern village, two rolling mills, for the manufacture of copper bolts and sheathing, on a large scale; two...furnaces for refining copper , and casting bells and brass cannon (operated by Paul Revere): forges and furnaces for the manufacture of iron wheels and...Dedha Granodiorite, Westwood Granite, Sharon Syenite, and Blue Rills Granite Porphyry . Crushed Stone. The Mattapan Volcanic Complex and Westwood

Analysis and interpretation of a unique Arabic finger ring from the Viking Age town of Birka, Sweden.

PubMed

Wärmländer, Sebastian K T S; Wåhlander, Linda; Saage, Ragnar; Rezakhani, Khodadad; Hamid Hassan, Saied A; Neiß, Michael

2015-01-01

In this work we used non-destructive SEM imaging and EDS analysis to characterize the material composition of an Arabic finger ring, which was found in a 9(th) c. woman's grave at the Viking Age (A.D. 793-1066) trading center of Birka, Sweden. The ring is set with a violet stone inscribed with Arabic Kufic writing, here interpreted as reading "il-la-lah", i.e. "For/to Allah". The stone was previously thought to be an amethyst, but the current results show it to be coloured glass. The ring has been cast in a high-grade silver alloy (94.5/5.5 Ag/Cu) and retains the post-casting marks from the filing done to remove flash and mold lines. Thus, the ring has rarely been worn, and likely passed from the silversmith to the woman buried at Birka with few owners in between. The ring may therefore constitute material evidence for direct interactions between Viking Age Scandinavia and the Islamic world. Being the only ring with an Arabic inscription found at a Scandinavian archaeological site, it is a unique object among Swedish Viking Age material. The technical analysis presented here provides a better understanding of the properties and background of this intriguing piece of jewelry. © Wiley Periodicals, Inc.

Nephrolithiasis: Molecular Mechanism of Renal Stone Formation and the Critical Role Played by Modulators

PubMed Central

Aggarwal, Kanu Priya; Narula, Shifa; Kakkar, Monica

2013-01-01

Urinary stone disease is an ailment that has afflicted human kind for many centuries. Nephrolithiasis is a significant clinical problem in everyday practice with a subsequent burden for the health system. Nephrolithiasis remains a chronic disease and our fundamental understanding of the pathogenesis of stones as well as their prevention and cure still remains rudimentary. Regardless of the fact that supersaturation of stone-forming salts in urine is essential, abundance of these salts by itself will not always result in stone formation. The pathogenesis of calcium oxalate stone formation is a multistep process and essentially includes nucleation, crystal growth, crystal aggregation, and crystal retention. Various substances in the body have an effect on one or more of the above stone-forming processes, thereby influencing a person's ability to promote or prevent stone formation. Promoters facilitate the stone formation while inhibitors prevent it. Besides low urine volume and low urine pH, high calcium, sodium, oxalate and urate are also known to promote calcium oxalate stone formation. Many inorganic (citrate, magnesium) and organic substances (nephrocalcin, urinary prothrombin fragment-1, osteopontin) are known to inhibit stone formation. This review presents a comprehensive account of the mechanism of renal stone formation and the role of inhibitors/promoters in calcium oxalate crystallisation. PMID:24151593

Renal-Stone Risk Assessment During Space Shuttle Flights

NASA Technical Reports Server (NTRS)

Whitson, Peggy A.; Pietrzyk, Robert A.; Pak, Charles Y. C.

1996-01-01

The metabolic and environmental factors influencing renal stone formation before, during, and after Space Shuttle flights were assessed. We established the contributing roles of dietary factors in relationship to the urinary risk factors associated with renal stone formation. 24-hr urine samples were collected prior to, during space flight, and following landing. Urinary factors associated with renal stone formation were analyzed and the relative urinary supersaturation ratios of calcium oxalate, calcium phosphate (brushite), sodium urate, struvite and uric acid were calculated. Food and fluid consumption was recorded for a 48-hr period ending with the urine collection. Urinary composition changed during flight to favor the crystallization of stone-forming salts. Factors that contributed to increased potential for stone formation during space flight were significant reductions in urinary pH and increases in urinary calcium. Urinary output and citrate, a potent inhibitor of calcium-containing stones, were slightly reduced during space flight. Dietary intakes were significantly reduced for a number of variables, including fluid, energy, protein, potassium, phosphorus and magnesium. This is the first in-flight characterization of the renal stone forming potential in astronauts. With the examination of urinary components and nutritional factors, it was possible to determine the factors that contributed to increased risk or protected from risk. In spite of the protective components, the negative contributions to renal stone risk predominated and resulted in a urinary environment that favored the supersaturation of stone-forming salts. The importance of the hypercalciuria was noted since renal excretion was high relative to the intake.

Renal stone risk assessment during Space Shuttle flights

NASA Technical Reports Server (NTRS)

Whitson, P. A.; Pietrzyk, R. A.; Pak, C. Y.

1997-01-01

PURPOSE: The metabolic and environmental factors influencing renal stone formation before, during, and after Space Shuttle flights were assessed. We established the contributing roles of dietary factors in relationship to the urinary risk factors associated with renal stone formation. MATERIALS AND METHODS: 24-hr. urine samples were collected prior to, during space flight, and following landing. Urinary and dietary factors associated with renal stone formation were analyzed and the relative urinary supersaturation of calcium oxalate, calcium phosphate (brushite), sodium urate, struvite and uric acid were calculated. RESULTS: Urinary composition changed during flight to favor the crystallization of calcium-forming salts. Factors that contributed to increased potential for stone formation during space flight were significant reductions in urinary pH and increases in urinary calcium. Urinary output and citrate, a potent inhibitor of calcium-containing stones, were slightly reduced during space flight. Dietary intakes were significantly reduced for a number of variables, including fluid, energy, protein, potassium, phosphorus and magnesium. CONCLUSIONS: This is the first in-flight characterization of the renal stone forming potential in astronauts. With the examination of urinary components and nutritional factors, it was possible to determine the factors that contributed to increased risk or protected from risk. In spite of the protective components, the negative contributions to renal stone risk predominated and resulted in a urinary environment that favored the supersaturation of stone-forming salts. Dietary and pharmacologic therapies need to be assessed to minimize the potential for renal stone formation in astronauts during/after space flight.

Development of cast alumina-forming austenitic stainless steels

DOE PAGES

Muralidharan, G.; Yamamoto, Y.; Brady, M. P.; ...

2016-09-06

Cast Fe-Ni-Cr chromia-forming austenitic stainless steels with Ni levels up to 45 wt. % are used at high temperatures in a wide range of industrial applications that demand microstructural stability, corrosion resistance, and creep strength. Although alumina scales offer better corrosion protection at these temperatures, designing cast austenitic alloys that form a stable alumina scale and achieve creep strength comparable to existing cast chromia-forming alloys is challenging. This work outlines the development of cast Fe-Ni-Cr-Al austenitic stainless steels containing about 25 wt. % Ni with good creep strength and the ability to form a protective alumina scale for use atmore » temperatures up to 800 C - 850 C in H 2O-, S-, and C- containing environments. Creep properties of the best alloy were comparable to that of HK-type cast chromia-forming alloy along with improved oxidation resistance typical of alumina-forming alloys. Lastly, challenges in the design of cast alloys and a potential path to increasing the temperature capability are discussed.« less

Development of Cast Alumina-Forming Austenitic Stainless Steels

NASA Astrophysics Data System (ADS)

Muralidharan, G.; Yamamoto, Y.; Brady, M. P.; Walker, L. R.; Meyer, H. M., III; Leonard, D. N.

2016-11-01

Cast Fe-Ni-Cr chromia-forming austenitic stainless steels with Ni levels up to 45 wt.% are used at high temperatures in a wide range of industrial applications that demand microstructural stability, corrosion resistance, and creep strength. Although alumina scales offer better corrosion protection at these temperatures, designing cast austenitic alloys that form a stable alumina scale and achieve creep strength comparable to existing cast chromia-forming alloys is challenging. This work outlines the development of cast Fe-Ni-Cr-Al austenitic stainless steels containing about 25 wt.% Ni with good creep strength and the ability to form a protective alumina scale for use at temperatures up to 800-850°C in H2O-, S-, and C-containing environments. Creep properties of the best alloy were comparable to that of HK-type cast chromia-forming alloys along with improved oxidation resistance typical of alumina-forming alloys. Challenges in the design of cast alloys and a potential path to increasing the temperature capability are discussed.

Similarity of urinary risk factors among stone-forming patients in five regions of the United States

NASA Technical Reports Server (NTRS)

Harvey, J. A.; Hill, K. D.; Pak, C. Y.

1990-01-01

Study Objective: To compare urinary biochemical risk factors among stone-forming patients in the Southeast (SE) or "stone belt" versus four other regions of the United States. Design: Prospective biochemical survey for regional comparisons. Setting: Referral-based nephrolithiasis clinics, urologists, nephrologists, and family practitioners. Patients: Consecutive sample of 3473 stone-forming patients who submitted 24-hour urine collections for biochemical analyses of stone-forming risk factors. Interventions: None. Subjects taking medication known to interfere with stone-forming risk factors were deleted from the final data compilation. Measurements and Main Results: Overall, the mean values for each urinary parameter spanned a narrow range without significant difference between the five regions. Among "metabolic" factors, 40% in the SE had hypercalciuria (> 6.25 mmol/d), compared to 35%-43% in other regions, and hyperuricosuria (> 4.2 mmol/d) was found in 16% in the SE versus 17%-19% elsewhere. Among "environmental" factors, low urine volume ( < 2 L/d) was found in 77% patients in the SE compared to 69%-78% elsewhere, and high sodium was encountered in 27% in the SE versus 24%-29% elsewhere. No differences were noted in occurrence of other abnormal risk factors: hyperoxaluria, hypocitraturia, low pH, high sulfate, high phosphorus, or low magnesium. Conclusions: Despite expected regional differences in nutritional and environmental influences, the results of this study showed a striking similarity in urinary biochemical risk factor profiles of stone-formers in all five regions of the United States.

Secondary Waste Form Screening Test Results—THOR® Fluidized Bed Steam Reforming Product in a Geopolymer Matrix

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pires, Richard P.; Westsik, Joseph H.; Serne, R. Jeffrey

2011-07-14

Screening tests are being conducted to evaluate waste forms for immobilizing secondary liquid wastes from the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Plans are underway to add a stabilization treatment unit to the Effluent Treatment Facility to provide the needed capacity for treating these wastes from WTP. The current baseline is to use a Cast Stone cementitious waste form to solidify the wastes. Through a literature survey, DuraLith alkali-aluminosilicate geopolymer, fluidized-bed steam reformation (FBSR) granular product encapsulated in a geopolymer matrix, and a Ceramicrete phosphate-bonded ceramic were identified both as candidate waste forms and alternatives to the baseline.more » These waste forms have been shown to meet waste disposal acceptance criteria, including compressive strength and universal treatment standards for Resource Conservation and Recovery Act (RCRA) metals (as measured by the toxicity characteristic leaching procedure [TCLP]). Thus, these non-cementitious waste forms should also be acceptable for land disposal. Information is needed on all four waste forms with respect to their capability to minimize the release of technetium. Technetium is a radionuclide predicted to be in the secondary liquid wastes in small quantities, but the Integrated Disposal Facility (IDF) risk assessment analyses show that technetium, even at low mass, produces the largest contribution to the estimated IDF disposal impacts to groundwater.« less

Kidney stones.

PubMed

Khan, Saeed R; Pearle, Margaret S; Robertson, William G; Gambaro, Giovanni; Canales, Benjamin K; Doizi, Steeve; Traxer, Olivier; Tiselius, Hans-Göran

2016-02-25

Kidney stones are mineral deposits in the renal calyces and pelvis that are found free or attached to the renal papillae. They contain crystalline and organic components and are formed when the urine becomes supersaturated with respect to a mineral. Calcium oxalate is the main constituent of most stones, many of which form on a foundation of calcium phosphate called Randall's plaques, which are present on the renal papillary surface. Stone formation is highly prevalent, with rates of up to 14.8% and increasing, and a recurrence rate of up to 50% within the first 5 years of the initial stone episode. Obesity, diabetes, hypertension and metabolic syndrome are considered risk factors for stone formation, which, in turn, can lead to hypertension, chronic kidney disease and end-stage renal disease. Management of symptomatic kidney stones has evolved from open surgical lithotomy to minimally invasive endourological treatments leading to a reduction in patient morbidity, improved stone-free rates and better quality of life. Prevention of recurrence requires behavioural and nutritional interventions, as well as pharmacological treatments that are specific for the type of stone. There is a great need for recurrence prevention that requires a better understanding of the mechanisms involved in stone formation to facilitate the development of more-effective drugs.

Evaluation of outgassing, tear strength, and detail reproduction in alginate substitute materials.

PubMed

Baxter, R T; Lawson, N C; Cakir, D; Beck, P; Ramp, L C; Burgess, J O

2012-01-01

To compare three alginate substitute materials to an alginate impression material for cast surface porosity (outgassing), tear strength, and detail reproduction. Detail reproduction tests were performed following American National Standards Institute/American Dental Association (ANSI/ADA) Specification No. 19. To measure tear strength, 12 samples of each material were made using a split mold, placed in a water bath until testing, and loaded in tension until failure at a rate of 500 mm/min using a universal testing machine. For cast surface porosity testing, five impressions of a Teflon mold with each material were placed in a water bath (37.8°C) for the in-mouth setting time and poured with vacuum-mixed Silky Rock die stone at 5, 10, 30, and 60 minutes from the start of mixing. The gypsum samples were analyzed with a digital microscope for surface porosity indicative of hydrogen gas release by comparing the surface obtained at each interval with four casts representing no, little, some, and significant porosity. Data analysis was performed using parametric and Kruskal-Wallis analysis of variance (ANOVA), Tukey/Kramer post-hoc tests (α=0.05), and individual Mann-Whitney U tests (α=0.0167). All alginate substitute materials passed the detail reproduction test. Tear strength of the alginate substitute materials was significantly better than alginate and formed three statistically different groups: AlgiNot had the lowest tear strength, Algin-X Ultra had the highest tear strength, and Position Penta Quick had intermediate tear strength. Significant variation in outgassing existed between materials and pouring times (p<0.05). All alginate substitute materials exhibited the least outgassing and cast porosity 60 minutes after mixing. Detail reproduction and tear strength of alginate substitute materials were superior to traditional alginate. The outgassing effect was minimal for most materials tested. Alginate substitute materials are superior replacements for irreversible hydrocolloid.

Evaluating the Use of Synthetic Replicas for SEM Identification of Bloodstains (with Emphasis on Archaeological and Ethnographic Artifacts).

PubMed

Hortolà, Policarp

2015-12-01

Some archaeological or ethnographic specimens are unavailable for direct examination using a scanning electron microscope (SEM) due to methodological obstacles or legal issues. In order to assess the feasibility of using SEM synthetic replicas for the identification of bloodstains (BSs) via morphology of red blood cells (RBCs), three fragments of different natural raw material (inorganic, stone; plant, wood; animal, shell) were smeared with peripheral human blood. Afterwards, molds and casts of the bloodstained areas were made using vinyl polysiloxane (VPS) silicone impression and polyurethane (PU) resin casting material, respectively. Then, the original samples and the resulting casts were coated with gold and examined in secondary-electron mode using a high-vacuum SEM. Results suggest that PU resin casts obtained from VPS silicone molds can preserve RBC morphology in BSs, and consequently that synthetic replicas are feasible for SEM identification of BSs on cultural heritage specimens made of natural raw materials. Although the focus of this study was on BSs, the method reported in this paper may be applicable to organic residues other than blood, as well as to the surface of other specimens when, for any reason, the original is unavailable for an SEM.

Translocation of mineralo-organic nanoparticles from blood to urine: a new mechanism for the formation of kidney stones?

PubMed

Martel, Jan; Wu, Cheng-Yeu; Young, John D

2016-09-01

Recent studies indicate that mineralo-organic nanoparticles form in various human body fluids, including blood and urine. These nanoparticles may form within renal tubules and increase in size in supersaturated urine, eventually leading to the formation of kidney stones. Here, we present observations suggesting that mineralo-organic nanoparticles found in blood may induce kidney stone formation via an alternative mechanism in which the particles translocate through endothelial and renal epithelial cells to reach urine. We propose that this alternative mechanism of kidney stone formation and the study of mineralo-organic nanoparticles in general may provide novel strategies for the early detection and treatment of ectopic calcifications and kidney stones.

Proteus mirabilis fimbriae- and urease-dependent clusters assemble in an extracellular niche to initiate bladder stone formation.

PubMed

Schaffer, Jessica N; Norsworthy, Allison N; Sun, Tung-Tien; Pearson, Melanie M

2016-04-19

The catheter-associated uropathogenProteus mirabilisfrequently causes urinary stones, but little has been known about the initial stages of bladder colonization and stone formation. We found thatP. mirabilisrapidly invades the bladder urothelium, but generally fails to establish an intracellular niche. Instead, it forms extracellular clusters in the bladder lumen, which form foci of mineral deposition consistent with development of urinary stones. These clusters elicit a robust neutrophil response, and we present evidence of neutrophil extracellular trap generation during experimental urinary tract infection. We identified two virulence factors required for cluster development: urease, which is required for urolithiasis, and mannose-resistantProteus-like fimbriae. The extracellular cluster formation byP. mirabilisstands in direct contrast to uropathogenicEscherichia coli, which readily formed intracellular bacterial communities but not luminal clusters or urinary stones. We propose that extracellular clusters are a key mechanism ofP. mirabilissurvival and virulence in the bladder.

Cast Iron in The 19th Century Building Equipment

NASA Astrophysics Data System (ADS)

Kwasek, Michał; Piwek, Aleksander

2017-10-01

Cast iron is a material, characteristics of which enable to receive extremely artistic elements. It maintains good strength properties at the same time. That combination of these seemingly contrary traits makes it a commodity that was widely used in the 19th century industry and architecture. These usages were not only as decorative elements, technical and structural ones. The production of new household utilities started, which made people’s lives more comfortable. Cast iron allowed for fast and cheap production while maintaining high aesthetic qualities. Useful elements, which often were ornamental parts of buildings were created. The aim of the article is to characterise elements of interior equipment of the 19th century building that are made of cast iron. As it appears from performed bibliography, archival and field studies, the ways of exploitation are very broad. Some were mounted into the building; the others were a mobile equipment. As it occurred they were most commonly used as functional items. Cast iron was used to produce the minor elements, which were only parts of the bigger wooden or stone items. Notwithstanding, there were also bigger ones casted as a whole, and frequently ones that were assembled from many elements. Nowadays, elements of an interior feature are one of the subjects of study during the restoration work of the buildings. They can provide important information about the building and the way people lived and are considered as the essential part of historical objects.

Incidence and management of dialysis patients with renal calculi.

PubMed

Viterbo, Rosalia; Mydlo, Jack H

2002-01-01

The incidence of renal stones in patients on dialysis, while lower in number compared to the general population because of decreased renal function, is nonetheless a clinical dilemma. We wanted to evaluate the incidence and management of stone disease in patients on hemodialysis. We reviewed the literature from 1966 to the present using Medline. Study inclusion criteria were detection and treatment of stone disease in both hemodialysis and peritoneal dialysis patients. It is estimated that between 5 and 13% of all dialysis patients will develop symptomatic renal calculi and many more asymptomatic calculi. Many of the stone-forming dialysis patients will have recurring stone disease with one study finding an 83.3% recurrence rate. Since dialysis patients have a wide range of urine output, the clinician should be alert to the possibility of stone formation. We recommend yearly ultrasound examinations on all dialysis patients as well as citrate and magnesium supplements with careful follow-up of laboratory results and urine electrolytes. We also recommend careful follow-up of all patients on aluminum-hydroxide phosphate binders as they are predisposed to form Al-Mg-urate stones. For those dialysis patients that form renal calculi, watchful waiting and symptomatic treatment is recommended since almost all patients will spontaneously pass their stones. However, ESWL and other current modalities may be used with no greater morbidity compared to nondialysis cohorts. We also suggest that patients with severe recurring intractable stone disease who are candidates for renal transplantation should be offered bilateral nephrectomies. Copyright 2002 S. Karger AG, Basel

An In Vitro Comparison of the Marginal Adaptation Accuracy of CAD/CAM Restorations Using Different Impression Systems.

PubMed

Shembesh, Marwa; Ali, Ala; Finkelman, Matthew; Weber, Hans-Peter; Zandparsa, Roya

2017-10-01

To compare the marginal adaptation of 3-unit zirconia fixed dental prostheses (FDPs) obtained from intraoral digital scanners (Lava True Definition, Cadent iTero), scanning of a conventional silicone impression, and the resulting master cast with an extraoral scanner (3Shape lab scanner). One reference model was fabricated from intact, non-carious, unrestored human mandibular left first premolar and first molar teeth (teeth #19 and 21), prepared for a three-unit all-ceramic FDP. Impressions of the reference model were obtained using four impression systems (n = 10), group 1 (PVS impression scan), group 2 (stone cast scan), group 3 (Cadent iTero), and group 4 (Lava True Defintion). Then the three-unit zirconia FDPs were milled. Marginal adaptation of the zirconia FDPs was evaluated using an optical comparator at four points on each abutment. The mean (SD) was reported for each group. One-way ANOVA was used to assess the statistical significance of the results, with post hoc tests conducted via Tukey's HSD. p < 0.05 was considered statistically significant. All analyses were done using SPSS 22.0. The mean (SD) marginal gaps for the recorded data from highest to lowest were silicone impression scans 81.4 μm (6.8), Cadent iTero scan 62.4 μm (5.0), master cast scan 50.2 μm (6.1), and Lava True definition scan 26.6 μm (4.7). One-way ANOVA revealed significant differences (p < 0.001) in the mean marginal gap among the groups. The Tukey's HSD tests demonstrated that the differences between all groups (silicone impression scan, master cast scan, Lava True definition scan, iTero Cadent scan) were statistically significant (all p < 0.001). On the basis of the criterion of 120 μm as the limit of clinical acceptance, all marginal discrepancy values of all groups were clinically acceptable. Within the confines of this in vitro study, it can be concluded that the marginal gap of all impression techniques was within the acceptable clinical limit (120 μm). Group 4 (Lava True Defintion) showed the lowest average gap among all groups followed by group 2 (stone cast scan), group 3 (Cadent iTero), and group 1 (PVS impression scan); these differences were statistically significant. © 2016 by the American College of Prosthodontists.

Drropulli Stone and Gjirokastra World Heritage in Albania

NASA Astrophysics Data System (ADS)

Serjani, Afat; Kramar, Sabina

2013-04-01

Ancient Gjirokastra City and Dervician stone deposit, there are located next to each other, in south of Albania, at foots of eastern slope of "Wide Mountain". Building stone it is represented by micritic limestone of white, red and blue colour, formed during Palaeocene-Eocene Period. It contains fossils of rounded forms and it is known and exploited since the ancient times. Argjirokastra, Argjiro's City, appeared since the IV-th Century BC (V.Tola, 2011). Stone City has in its centre Majestic Fortress of a big cruiser view, which is seen from long distance, from all sides of Drinos Valley. "This Majestic Monument of Albanian vigour has an astonishing elegance" has written E. Hoxha (1983). Watching Gjirokastra you will remind "Chronic in Stone", the book of Ismail Kadare, great writer, born in Gjirokastra. All buildings here are of stone. The Large Fortress and high houses as castles are built by stone, and covered by stone tiles. The walls and minarets of religious buildings are of stone. The gates of houses and yards are of engraved stone, protected by metallic nets of artistic forms. The house's walls are built by big stone, while the walls of yards are by small stone of white colour, some times intercalated with lines of red, blue stone. The combination of different colour stone is another one artistic beauty of walls. The roads are paved by black cobblestones of flysch sandstone for protection by slips, some times combined with white limestone mosaics. Steps of houses and roads are by white stone, often reworked masterfully. "Such stones, reworked by very fine skilfully, can not be found in any other place of the World, only in Anadoll" has written on 1 665 Evliya Celepi (2003). Buildings are of specific architecture and by good style. The accounts of the basis are done to keep "houses as castle". The walls have wood antiseismic layers. The architecture of houses, gates, angles, windows, with predomination of arc forms, with engraved stones and ornaments it is everywhere evident. The ceilings of houses there are with artistic works and ornaments of different times. Houses are of balconies with balustrades, and from characteristic windows are hanging down flowers. Architecture feature of Medieval period, there are symbolised in most of houses and in Qafa e Pazarit ("Bazaar Pass"), where are crossed all roads of the ancient City. From the Fortress below your foots there are different parts of stone City. If you like to be astonished, please, get up to the Keculla Point and watch the Stone City, Drinos Valley, and Lunxheria Mountains! In Gjirokastra Region there are Antigonea Archaeological Park and Sofratika Amphitheatre. Gjirokastra has a very rich geoheritage and bioheritage such as: Viroi artesian spring, Skotini Cave, Cajupi Field Landscape etc. Since 1961, Gjirokastra was proclaimed Museum City under the protection, and on 2005 was included in UNESCO World Cultural Heritage.

SEM/EDX and vis spectrophotometry study of the stability of resin-bound mortars used for casting replicas and filling missing parts of historic stone fountains.

PubMed

Roig-Salom, José-Luis; Doménech-Carbó, María-Teresa; de la Cruz-Cañizares, Juana; Bolívar-Galiano, Fernando; Pelufo-Carbonell, María-José; Peraza-Zurita, Yaiza

2003-04-01

A study by SEM/EDX and spectrophotometry in the visible region attempting to assess the stability of new resin-bound mortars used for casting replicas of marble historic fountains is presented in this paper. Different accelerating tests such as thermal ageing, UV light ageing, ageing in an SO(2) pollutant chamber, freezing cycles ageing, salt crystallisation ageing, natural ageing and biological attack have been applied to a series of test specimens prepared with polyester-, epoxy- and gel-coat-bound mortars. Examination of morphology, measurement of chemical composition and chromatic coordinates before and after ageing treatments establish the higher stability and resistance properties of these resin-bound mortars by comparison to those from the natural marbles.

Mineral resource of the month: manganese

USGS Publications Warehouse

Corathers, Lisa A.

2012-01-01

Manganese is a silver-colored metal resembling iron and often found in conjunction with iron. The earliest-known human use of manganese compounds was in the Stone Age, when early humans used manganese dioxide as pigments in cave paintings. In ancient Rome and Egypt, people started using it to color or remove the color from glass - a practice that continued to modern times. Today, manganese is predominantly used in metallurgical applications as an alloying addition, particularly in steel and cast iron production. Steel and cast iron together provide the largest market for manganese (historically 85 to 90 percent), but it is also alloyed with nonferrous metals such as aluminum and copper. Its importance to steel cannot be overstated, as almost all types of steel contain manganese and could not exist without it.

Unenhanced CT findings can predict the development of urinary calculi in stone-free patients.

PubMed

Ciudin, Alexandru; Luque Galvez, Maria Pilar; Salvador Izquierdo, Rafael; Franco de Castro, Agustin; Garcia-Cruz, Eduardo; Alcover García, Juan; Alvarez-Vijande García, Jose Ricardo; Nicolau, Carlos; Alcaraz Asensio, Antonio

2012-09-01

To determine if calcium deposits in the papillae can be identified by unenhanced computed tomography (uCT) even before renal stones develop. A retrospective review of 413 patients with calculi identified 31 patients (stone-forming group) with a history of urinary tract calculi with a calculus demonstrated by uCT and a stone-free uCT before calculi had developed. The control group (n = 31) was composed of live kidney donors with no history of calculi and a stone-free uCT. CT attenuation was measured in all CTs using two regions of interest of 0.05 cm(2) and 0.1 cm(2) over the tip and the neighbouring area of the papillae. Student's and Wilcoxon t-tests were used for comparing results in the two groups. The attenuation of the tip of the papilla was higher in the stone-forming group when compared to the controls after (45.2 HU versus 32.1 HU, P = 0.001) and even before frank calculi had developed (44.2 HU versus 32.1 HU, P = 0.003). There was no significant difference in papillary attenuation in the stone group before and after calculi had developed (45.2 HU versus 44.2 HU, P = 0.82). Stone-forming patients exhibit higher papillary density even before calculi develop. This could define a population at risk of developing calculi.

Primary in situ extracorporeal shock wave lithotripsy in the management of ureteric calculi: results with a third-generation lithotripter.

PubMed

Gnanapragasam, V J; Ramsden, P D; Murthy, L S; Thomas, D J

1999-11-01

To review the results of primary in situ extracorporeal shock wave lithotripsy (ESWL) for the treatment of ureteric stones using a third-generation lithotripter, the Dornier MFL 5000 (Dornier Medizentechnic, Germany). The study comprised a retrospective review of treatment outcome in 180 patients with 196 stones who were treated with primary in situ ESWL, assessing the success of this approach and establishing reasons for failure. At the 3-month follow-up, 88% of patients were stone-free; 21 patients failed ESWL and were treated by ureteroscopic stone extraction with no complications. Stone-free rates were 90% for upper ureteric, 89% for middle-third and 86% for lower-third calculi. Twenty-one patients required auxiliary procedures in the form of JJ stenting or nephrostomy. Failure of ESWL was associated with stone size (>1.3 cm) but not location or inadequate treatment. Where prompt access to ESWL is available, primary in situ ESWL remains an effective form of treatment for all ureteric calculi, although stone-free rates are lower for larger stones.

Kidney stones

PubMed Central

Khan, Saeed R.; Pearle, Margaret S.; Robertson, William G.; Gambaro, Giovanni; Canales, Benjamin K.; Doizi, Steeve; Traxer, Olivier; Tiselius, Hans-Göran

2017-01-01

Kidney stones are mineral deposits in the renal calyces and pelvis that are found free or attached to the renal papillae. They contain crystalline and organic components and are formed when the urine becomes supersaturated with respect to a mineral. Calcium oxalate is the main constituent of most stones, many of which form on a foundation of calcium phosphate called Randall’s plaques, which are present on the renal papillary surface. Stone formation is highly prevalent, with rates of up to 14.8% and increasing, and a recurrence rate of up to 50% within the first 5 years of the initial stone episode. Obesity, diabetes, hypertension and metabolic syndrome are considered risk factors for stone formation, which, in turn, can lead to hypertension, chronic kidney disease and end-stage renal disease. Management of symptomatic kidney stones has evolved from open surgical lithotomy to minimally invasive endourological treatments leading to a reduction in patient morbidity, improved stone-free rates and better quality of life. Prevention of recurrence requires behavioural and nutritional interventions, as well as pharmacological treatments that are specific for the type of stone. There is a great need for recurrence prevention that requires a better understanding of the mechanisms involved in stone formation to facilitate the development of more-effective drugs. PMID:27188687

Urine risk factors in children with calcium kidney stones and their siblings

PubMed Central

Bergsland, Kristin J.; Coe, Fredric L.; White, Mark D.; Erhard, Michael J.; DeFoor, William R.; Mahan, John D.; Schwaderer, Andrew L.; Asplin, John R.

2012-01-01

Calcium nephrolithiasis in children is increasing in prevalence and tends to be recurrent. Although children have a lower incidence of nephrolithiasis than adults, its etiology in children is less well understood; hence treatments targeted for adults may not be optimal in children. To better understand metabolic abnormalities in stone forming children, we compared chemical measurements and the crystallization properties of 24-hour urine collections from 129 stone formers matched to 105 non-stone forming siblings and 183 normal, healthy children with no family history of stones; all aged 6 to 17 years. The principal risk factor for calcium stone formation was hypercalciuria. Stone formers have strikingly higher calcium excretion along with high supersaturation for calcium oxalate and calcium phosphate, and a reduced distance between the upper limit of metastability and supersaturation for calcium phosphate, indicating increased risk of calcium phosphate crystallization. Other differences in urine chemistry that exist between adult stone formers and normal individuals such as hyperoxaluria, hypocitraturia, abnormal urine pH and low urine volume were not found in these children. Hence, hypercalciuria and a reduction in the gap between calcium phosphate upper limit of metastability and supersaturation are crucial determinants of stone risk. This highlights the importance of managing hypercalciuria in children with calcium stones. PMID:22358148

Urine risk factors in children with calcium kidney stones and their siblings.

PubMed

Bergsland, Kristin J; Coe, Fredric L; White, Mark D; Erhard, Michael J; DeFoor, William R; Mahan, John D; Schwaderer, Andrew L; Asplin, John R

2012-06-01

Calcium nephrolithiasis in children is increasing in prevalence and tends to be recurrent. Although children have a lower incidence of nephrolithiasis than adults, its etiology in children is less well understood; hence, treatments targeted for adults may not be optimal in children. To better understand metabolic abnormalities in stone-forming children, we compared chemical measurements and the crystallization properties of 24-h urine collections from 129 stone formers matched to 105 non-stone-forming siblings and 183 normal, healthy children with no family history of stones, all aged 6 to 17 years. The principal risk factor for calcium stone formation was hypercalciuria. Stone formers have strikingly higher calcium excretion along with high supersaturation for calcium oxalate and calcium phosphate, and a reduced distance between the upper limit of metastability and supersaturation for calcium phosphate, indicating increased risk of calcium phosphate crystallization. Other differences in urine chemistry that exist between adult stone formers and normal individuals such as hyperoxaluria, hypocitraturia, abnormal urine pH, and low urine volume were not found in these children. Hence, hypercalciuria and a reduction in the gap between calcium phosphate upper limit of metastability and supersaturation are crucial determinants of stone risk. This highlights the importance of managing hypercalciuria in children with calcium stones.

Dimensional accuracy of resultant casts made by a monophase, one-step and two-step, and a novel two-step putty/light-body impression technique: an in vitro study.

PubMed

Caputi, Sergio; Varvara, Giuseppe

2008-04-01

Dimensional accuracy when making impressions is crucial to the quality of fixed prosthodontic treatment, and the impression technique is a critical factor affecting this accuracy. The purpose of this in vitro study was to compare the dimensional accuracy of a monophase, 1- and 2-step putty/light-body, and a novel 2-step injection impression technique. A stainless steel model with 2 abutment preparations was fabricated, and impressions were made 15 times with each technique. All impressions were made with an addition-reaction silicone impression material (Aquasil) and a stock perforated metal tray. The monophase impressions were made with regular body material. The 1-step putty/light-body impressions were made with simultaneous use of putty and light-body materials. The 2-step putty/light-body impressions were made with 2-mm-thick resin-prefabricated copings. The 2-step injection impressions were made with simultaneous use of putty and light-body materials. In this injection technique, after removing the preliminary impression, a hole was made through the polymerized material at each abutment edge, to coincide with holes present in the stock trays. Extra-light-body material was then added to the preliminary impression and further injected through the hole after reinsertion of the preliminary impression on the stainless steel model. The accuracy of the 4 different impression techniques was assessed by measuring 3 dimensions (intra- and interabutment) (5-mum accuracy) on stone casts poured from the impressions of the stainless steel model. The data were analyzed by 1-way ANOVA and Student-Newman-Keuls test (alpha=.05). The stone dies obtained with all the techniques had significantly larger dimensions as compared to those of the stainless steel model (P<.01). The order for highest to lowest deviation from the stainless steel model was: monophase, 1-step putty/light body, 2-step putty/light body, and 2-step injection. Significant differences among all of the groups for both absolute dimensions of the stone dies, and their percent deviations from the stainless steel model (P<.01), were noted. The 2-step putty/light-body and 2-step injection techniques were the most dimensionally accurate impression methods in terms of resultant casts.

Kidney Stones in Primary Hyperoxaluria: New Lessons Learnt

PubMed Central

Jacob, Dorrit E.; Grohe, Bernd; Geßner, Michaela; Beck, Bodo B.; Hoppe, Bernd

2013-01-01

To investigate potential differences in stone composition with regard to the type of Primary Hyperoxaluria (PH), and in relation to the patient’s medical therapy (treatment naïve patients versus those on preventive medication) we examined twelve kidney stones from ten PH I and six stones from four PH III patients. Unfortunately, no PH II stones were available for analysis. The study on this set of stones indicates a more diverse composition of PH stones than previously reported and a potential dynamic response of morphology and composition of calculi to treatment with crystallization inhibitors (citrate, magnesium) in PH I. Stones formed by PH I patients under treatment are more compact and consist predominantly of calcium-oxalate monohydrate (COM, whewellite), while calcium-oxalate dihydrate (COD, weddellite) is only rarely present. In contrast, the single stone available from a treatment naïve PH I patient as well as stones from PH III patients prior to and under treatment with alkali citrate contained a wide size range of aggregated COD crystals. No significant effects of the treatment were noted in PH III stones. In disagreement with findings from previous studies, stones from patients with primary hyperoxaluria did not exclusively consist of COM. Progressive replacement of COD by small COM crystals could be caused by prolonged stone growth and residence times in the urinary tract, eventually resulting in complete replacement of calcium-oxalate dihydrate by the monohydrate form. The noted difference to the naïve PH I stone may reflect a reduced growth rate in response to treatment. This pilot study highlights the importance of detailed stone diagnostics and could be of therapeutic relevance in calcium-oxalates urolithiasis, provided that the effects of treatment can be reproduced in subsequent larger studies. PMID:23940605

Metallurgical effects on titanium by laser welding on dental stone.

PubMed

Fujioka, Sonosuke; Kakimoto, Kazutoshi; Inoue, Taro; Okazaki, Joji; Komasa, Yutaka

2003-12-01

It is not known for certain that dental stone components influence titanium welding. In this study, we investigated metallurgical problems caused by laser welding on dental stones using wrought commercial pure (CP) titanium. A pulsed Nd:YAG laser irradiated a number of specimens' surfaces which were fixed on either a dental hard stone or a titanium plate. The metallurgical properties of the weld were evaluated using the Vickers hardness test, microstructure observation, fractured surface observation and quantitative analysis of oxygen and hydrogen. In the weld formed on the dental stone there was an increase in hardness, the existence of an acicular structure and a brittle fractured surface, and an increase in the oxygen and hydrogen concentrations compared with base metal. In the weld formed on the titanium plate, these changes were not observed. Therefore, it was demonstrated that laser welding on dental stones made the welds brittle.

Simulation of root forms using cellular automata model

NASA Astrophysics Data System (ADS)

Winarno, Nanang; Prima, Eka Cahya; Afifah, Ratih Mega Ayu

2016-02-01

This research aims to produce a simulation program for root forms using cellular automata model. Stephen Wolfram in his book entitled "A New Kind of Science" discusses the formation rules based on the statistical analysis. In accordance with Stephen Wolfram's investigation, the research will develop a basic idea of computer program using Delphi 7 programming language. To best of our knowledge, there is no previous research developing a simulation describing root forms using the cellular automata model compared to the natural root form with the presence of stone addition as the disturbance. The result shows that (1) the simulation used four rules comparing results of the program towards the natural photographs and each rule had shown different root forms; (2) the stone disturbances prevent the root growth and the multiplication of root forms had been successfully modeled. Therefore, this research had added some stones, which have size of 120 cells placed randomly in the soil. Like in nature, stones cannot be penetrated by plant roots. The result showed that it is very likely to further develop the program of simulating root forms by 50 variations.

Effect of Storage Time and Temperature on Dimensional Stability of Impressions Made with Zinc Oxide Impression Paste

PubMed Central

Habibzadeh, Sareh; Safaeian, Shima; Behruzibakhsh, Marjan; Kaviyani, Parisa; Kharazifard, Mohamadjavad

2016-01-01

Objectives: This study aimed to assess the effect of storage time and temperature on dimensional stability of impressions made with Cavex Outline zinc oxide impression paste. Materials and Methods: A round stainless steel mold with five grooves (three horizontal and two vertical) was used in this in-vitro experimental study. Cavex Outline impression paste was prepared according to the manufacturer’s instructions and applied to the mold. The mold was placed on a block and stored at 35°C and 100% humidity for setting. The impressions were poured with stone immediately and also after 30, 120, 240 and 420 minutes and 24 hours. The distance between the vertical lines on the casts was measured and compared with that in the immediately poured cast. Results: Storage in a refrigerator and at room temperature for zero to seven hours had no significant effect on dimensional stability of the impressions; however, 24 hours of storage in a refrigerator or at room temperature decreased the dimensional stability of Cavex Outline (P=0.001). Also, a significant association was found between dimensional changes following 24 hours of storage in a refrigerator (4°C) and at room temperature (23°C; P<0.01). Conclusions: The optimal pouring time of Cavex Outline impressions with stone is between zero to seven hours, and 24 hours of storage significantly decreases the dimensional stability. PMID:28392816

Calcium nephrolithiasis: effect of water hardness on urinary electrolytes.

PubMed

Schwartz, Bradley F; Schenkman, Noah S; Bruce, Jeremy E; Leslie, Stephen W; Stoller, Marshall L

2002-07-01

To analyze the impact of water hardness from public water supplies on calcium stone incidence and 24-hour urine chemistries in patients with known calcium urinary stone formation. Patients are frequently concerned that their public water supply may contribute to urinary stone disease. Investigators have documented an inverse relationship between water hardness and calcium lithogenesis. Others have found no such association. Patients who form calcium stones (n = 4833) were identified geographically by their zip code. Water hardness information from distinct geographic public water supplies was obtained, and patient 24-hour urine chemistries were evaluated. Drinking water hardness was divided into decile rankings on the basis of the public water supply information obtained from the Environmental Protection Agency. These data were compared with patient questionnaires and 24-hour urine chemistries. The calcium and magnesium levels in the drinking water were analyzed as independent variables. The number of total lifetime stone episodes was similar between patients residing in areas with soft public water and hard public water. Patients consuming the softest water decile formed 3.4 lifetime stones and those who consumed the hardest water developed 3.0 lifetime stones (P = 0.0017). The 24-hour urine calcium, magnesium, and citrate levels increased directly with drinking water hardness, and no significant change was found in urinary oxalate, uric acid, pH, or volume. The impact of water hardness on urinary stone formation remains unclear, despite a weak correlation between water hardness and urinary calcium, magnesium, and citrate excretion. Tap water, however, can change urinary electrolytes in patients who form calcium stones.

Vitamin D Supplementation in Submariners

DTIC Science & Technology

2008-12-02

prevalence of over 10% in men.71 Most stones are composed of calcium oxalate or calcium phosphate.72 It is the composition of these stones that...urine that combine with calcium to form calcium oxalate stones.77 One of the major factors that reduce hyperoxaluria is calcium in the diet. The... calcium in the intestinal lumen forms insoluble calcium salts with the oxalates and is not absorbed. A diet low in calcium will allow more oxalates to be

Proteus mirabilis fimbriae- and urease-dependent clusters assemble in an extracellular niche to initiate bladder stone formation

PubMed Central

Schaffer, Jessica N.; Norsworthy, Allison N.; Sun, Tung-Tien

2016-01-01

The catheter-associated uropathogen Proteus mirabilis frequently causes urinary stones, but little has been known about the initial stages of bladder colonization and stone formation. We found that P. mirabilis rapidly invades the bladder urothelium, but generally fails to establish an intracellular niche. Instead, it forms extracellular clusters in the bladder lumen, which form foci of mineral deposition consistent with development of urinary stones. These clusters elicit a robust neutrophil response, and we present evidence of neutrophil extracellular trap generation during experimental urinary tract infection. We identified two virulence factors required for cluster development: urease, which is required for urolithiasis, and mannose-resistant Proteus-like fimbriae. The extracellular cluster formation by P. mirabilis stands in direct contrast to uropathogenic Escherichia coli, which readily formed intracellular bacterial communities but not luminal clusters or urinary stones. We propose that extracellular clusters are a key mechanism of P. mirabilis survival and virulence in the bladder. PMID:27044107

A Comparative Evaluation of the Linear Dimensional Accuracy of Four Impression Techniques using Polyether Impression Material.

PubMed

Manoj, Smita Sara; Cherian, K P; Chitre, Vidya; Aras, Meena

2013-12-01

There is much discussion in the dental literature regarding the superiority of one impression technique over the other using addition silicone impression material. However, there is inadequate information available on the accuracy of different impression techniques using polyether. The purpose of this study was to assess the linear dimensional accuracy of four impression techniques using polyether on a laboratory model that simulates clinical practice. The impression material used was Impregum Soft™, 3 M ESPE and the four impression techniques used were (1) Monophase impression technique using medium body impression material. (2) One step double mix impression technique using heavy body and light body impression materials simultaneously. (3) Two step double mix impression technique using a cellophane spacer (heavy body material used as a preliminary impression to create a wash space with a cellophane spacer, followed by the use of light body material). (4) Matrix impression using a matrix of polyether occlusal registration material. The matrix is loaded with heavy body material followed by a pick-up impression in medium body material. For each technique, thirty impressions were made of a stainless steel master model that contained three complete crown abutment preparations, which were used as the positive control. Accuracy was assessed by measuring eight dimensions (mesiodistal, faciolingual and inter-abutment) on stone dies poured from impressions of the master model. A two-tailed t test was carried out to test the significance in difference of the distances between the master model and the stone models. One way analysis of variance (ANOVA) was used for multiple group comparison followed by the Bonferroni's test for pair wise comparison. The accuracy was tested at α = 0.05. In general, polyether impression material produced stone dies that were smaller except for the dies produced from the one step double mix impression technique. The ANOVA revealed a highly significant difference for each dimension measured (except for the inter-abutment distance between the first and the second die) between any two groups of stone models obtained from the four impression techniques. Pair wise comparison for each measurement did not reveal any significant difference (except for the faciolingual distance of the third die) between the casts produced using the two step double mix impression technique and the matrix impression system. The two step double mix impression technique produced stone dies that showed the least dimensional variation. During fabrication of a cast restoration, laboratory procedures should not only compensate for the cement thickness, but also for the increase or decrease in die dimensions.

Casting copper to tungsten for high-power arc lamp cathodes

NASA Technical Reports Server (NTRS)

Will, H. A.

1974-01-01

Voids forming at interface when copper is cast onto tungsten can be eliminated by adding wetting agent during casting process. Small amount of copper and nickel are cast onto thoriated tungsten insert, insert is recast with more copper to form electrode. Good thermal conductance results in long-lived cathode.

Effects of acid deposition on dissolution of carbonate stone during summer storms in the Adirondack Mountains, New York, 1987-89

USGS Publications Warehouse

Schuster, Paul F.; Reddy, Michael M.; Sherwood, S.I.

1994-01-01

This study is part of a long-term research program designed to identify and quantify acid rain damage to carbonate stone. Acidic deposition accelerates the dissolution of carbonate-stone monuments and building materials. Sequential sampling of runoff from carbonate-stone (marble) and glass (reference) microcatchments in the Adirondack Mountains in New York State provided a detailed record of the episodic fluctuations in rain rate and runoff chemistry during individual summer storms. Rain rate and chemical concentrations from carbonate-stone and glass runoff fluctuated three to tenfold during storms. Net calcium-ion concentrations from the carbonatestone runoff, a measure of stone dissolution, typically fluctuated twofold during these storms. High net sulfate and net calcium concentrations in the first effective runoff at the start of a storm indicated that atmospheric pollutants deposited on the stone surface during dry periods formed calcium sulfate minerals, an important process in carbonate stone dissolution. Dissolution of the carbonate stone generally increased up to twofold during coincident episodes of low rain rate (less than 5 millimeters per hour) and decreased rainfall (glass runoff) pH (less than 4.0); episodes of high rain rate (cloudbursts) were coincident with a rapid increase in rainfall pH and also a rapid decrease in the dissolution of carbonate-stone. During a storm, it seems the most important factors causing increased dissolution of carbonate stone are coincident periods of low rain rate and decreased rainfall pH. Dissolution of the carbonate stone decreased slightly as the rain rate exceeded about 5 millimeters per hour, probably in response to rapidly increasing rainfall pH during episodes of high rain rate and shorter contact time between the runoff and the stone surface. High runoff rates resulting from cloudbursts remove calcium sulfate minerals formed during dry periods prior to storms and also remove dissolution products formed in large measure by chemical weathering as a result of episodes of low rain rate and decreased rainfall pH during a storm.

Novel method for titanium crown casting using a combination of wax patterns fabricated by a CAD/CAM system and a non-expanded investment.

PubMed

Zhang, Zutai; Tamaki, Yukimichi; Hotta, Yasuhiro; Miyazaki, Takashi

2006-07-01

For titanium casting, most commercial investments for titanium recommend casting at a low mold temperature to reduce oxidation. However, the thermal expansion values of the molds at low casting temperatures may be insufficient. The purpose of the current study was to investigate the possibility of obtaining accurate titanium crown casts using wax pattern fabricated by a CAD/CAM system with a non-expanded mold. Three types of experimental magnesia-based investments (A, B and C) were made and their properties were evaluated for dental use. Two kinds of wax patterns for full-coverage coping crowns (S-0: cement space of 0 microm; S-20: cement space of 20 microm) were fabricated using a commercial CAD/CAM system. A traditional method (TM) using inlay wax was performed for comparison. The investment for titanium casting was decided from the fundamental data of experimental investments. Titanium crowns were replaced on the stone die and the thickness of the cement layer was evaluated. There were no significant differences for the setting time and setting expansion among the experimental investments, but the aluminous cement content played a role in hardening and contracting the mold. The fit of the titanium crowns differed significantly between the TM and the CAD/CAM system. The ranges of thickness obtained from the TM, S-0 and S-20 were 20.78-357.88 microm, 25.12-107.46 microm and 17.84-58.92 microm, respectively. High quality titanium crown casting was obtained using a combination of wax patterns fabricated by a CAD/CAM system and a non-expanded MgO-based investment.

MACHINING ELIMINATION THROUGH APPLICATION OF THREAD FORMING FASTENERS IN NET SHAPED CAST HOLES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cleaver, Ryan J; Cleaver, Todd H; Talbott, Richard

The ultimate objective of this work was to eliminate approximately 30% of the machining performed in typical automotive engine and transmission plants by using thread forming fasteners in as-cast holes of aluminum and magnesium cast components. The primary issues at the source of engineers reluctance to implementing thread forming fasteners in lightweight castings are: * Little proof of consistency of clamp load vs. input torque in either aluminum or magnesium castings. * No known data to understand the effect on consistency of clamp load as casting dies wear. The clamp load consistency concern is founded in the fact that amore » portion of the input torque used to create clamp load is also used to create threads. The torque used for thread forming may not be consistent due to variations in casting material, hole size and shape due to tooling wear and process variation (thermal and mechanical). There is little data available to understand the magnitude of this concern or to form the basis of potential solutions if the range of clamp load variation is very high (> +/- 30%). The range of variation that can be expected in as-cast hole size and shape over the full life cycle of a high pressure die casting die was established in previous work completed by Pacific Northwest National Laboratory, (PNNL). This established range of variation was captured in a set of 12 cast bosses by designing core pins at the size and draft angles identified in the sited previous work. The cast bosses were cut into nuts that could be used in the Ford Fastener Laboratory test-cell to measure clamp load when a thread forming fastener was driven into a cast nut. There were two sets of experiments run. First, a series of cast aluminum nuts were made reflecting the range of shape and size variations to be expected over the life cycle of a die casting die. Taptite thread forming fasteners, (a widely used thread forming fastener suitable for aluminum applications), were driven into the various cored, as-cast nuts at a constant input torque and resulting clamp loads were recorded continuously. The clamp load data was used to determine the range of clamp loads to be expected. The bolts were driven to failure. The clamp load corresponding to the target input of 18.5 Nm was recorded for each fastener. In a like fashion, a second set of experiments were run with cast magnesium nuts and ALtracs thread forming fasteners, (a widely used thread forming fastener suitable for magnesium applications). Again all clamp loads were recorded and analyzed similarly to the Taptites in aluminum cast nuts. Results from previous work performed on the same test cell for a Battelle project using standard M8 bolts into standard M8 nuts were included as a comparator for a standard bolt and nut application. The results for the thread forming fasteners in aluminum cast holes were well within industry expectations of +/- 30% for out of the box and robustness range testing. The results for the dry and lubed extreme conditions were only slightly higher than industry expectations at +/- 35.6%. However, when compared to the actual Battelle results (+/- 40%) for a standard bolt and nut the tread forming fasteners performed slightly better. The results for the thread forming fasteners in magnesium cast holes were all well within industry expectations of +/- 30% for all three conditions. The robustness range (.05mm larger and smaller holes than the expected wear pattern of a die casting die at full life cycle) results also fell within the industry expectations for standard threaded fasteners. These results were very encouraging. It was concluded that this work showed that clamp load variation with thread forming fasteners is consistent with industry expectations for standard steel bolts and nuts at +/- 30%. There does not appear to be any significant increase in clamp load variation due to the application of thread forming fasteners in as-cast holes of aluminum or magnesium over the effective life of a die casting mold. The fully implemented potential benefit of thread forming fasteners in as-cast holes of aluminum and magnesium is estimated to be 6 trillion Btu per year for North America. Economic benefit is estimated to be nearly $800 million per year. Environmental benefits and quality improvements will also result from full implementation of this technology.« less

40 CFR 421.1 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... to alloying or casting of nonferrous metals is limited to alloying or casting of hot metal directly... cooling is included in the aluminum forming, nonferrous metals forming, or metal molding and casting point...

Programmatic Considerations to Reduce the Risk of Adverse Renal Stone Events in Spaceflight

NASA Technical Reports Server (NTRS)

Antonsen, Erik; Pietrzyk, Robert

2017-01-01

Introduction: Microgravity exposure may alter the likelihood that astronauts will experience renal stones. The potential risk includes both acute and chronic health issues, with the potential for significant impact on mission objectives. Methods: To understand the role of the NASA's Human Research Program (HRP) research agenda in both preventing and addressing renal stones in spaceflight, current astronaut epidemiologic data and a summary of programmatic considerations are reviewed. Results: Although there has never been a symptomatic renal stone event in a U.S. crewmember during spaceflight, urine chemistry has been altered - likely due to induced changes in renal physiology as a result of exposure to microgravity. This may predispose astronauts to stone formation, leading the HRP to conduct and sponsor research to: 1) understand the risk of stone formation in space; 2) prevent stones from forming; and 3) address stones that may form by providing novel diagnostic and therapeutic approaches. Discussion: The development of a renal stone during spaceflight is a significant medical concern that requires the HRP to minimize this risk by providing the ability to prevent, diagnose, monitor and treat the condition during spaceflight. A discussion of the risk as NASA understands it is followed by an overview of the multiple mitigations currently under study, including novel ultrasound techniques for stone detection and manipulation, and how they may function as part of a larger exploration medical system.

Forgotten CBD stent (102 months) with stone-stent complex: A case report.

PubMed

Barai, Varsha; Hedawoo, Jagadish; Changole, Sanjay

2017-01-01

Choledocholithiasis is presence of stone in Common bile duct (CBD) which can be treated by endoscopy or surgery [1]. Retained foreign bodies like stents forms a nidus for stone formation resulting in pain, fever, jaundice. 60 years female patient admitted in surgery ward with features of cholangitis with computed tomography showing cholangitic abscess with dilated common bile duct and sludge around stent in situ. Stone was found at proximal end of stent during surgery. Stents may remain without complications or may migrate, and rarely form nidus for stone formation. If kept for long time they lead to bacterial proliferation, biofilm formation and precipitation of calcium bilirubinate presenting as fever, pain, jaundice. Stent-stone complex can be treated endoscopically and surgically [6,7]. As stent can cause stone formation, infection and other complications, timely removal of stent should advised. III-effects of stent in-situ should be explained, record should be maintained [8] and patient should be advised regular follow up and stent removal after 6 weeks. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Evaluation of a KeyStone/Tensar geogrid retaining wall system : final report.

DOT National Transportation Integrated Search

1992-01-01

The KeyStone/Tensar Geogrid retaining wall system is an alternative to conventional reinforced concrete retaining wall structures. KeyStone concrete wall units, Tensar geogrid, and compacted soils are combined to form a reinforced soil mass that toge...

Simulation of root forms using cellular automata model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winarno, Nanang, E-mail: nanang-winarno@upi.edu; Prima, Eka Cahya; Afifah, Ratih Mega Ayu

This research aims to produce a simulation program for root forms using cellular automata model. Stephen Wolfram in his book entitled “A New Kind of Science” discusses the formation rules based on the statistical analysis. In accordance with Stephen Wolfram’s investigation, the research will develop a basic idea of computer program using Delphi 7 programming language. To best of our knowledge, there is no previous research developing a simulation describing root forms using the cellular automata model compared to the natural root form with the presence of stone addition as the disturbance. The result shows that (1) the simulation usedmore » four rules comparing results of the program towards the natural photographs and each rule had shown different root forms; (2) the stone disturbances prevent the root growth and the multiplication of root forms had been successfully modeled. Therefore, this research had added some stones, which have size of 120 cells placed randomly in the soil. Like in nature, stones cannot be penetrated by plant roots. The result showed that it is very likely to further develop the program of simulating root forms by 50 variations.« less

Mineralogy and chemistry of urinary stones: patients from North Jordan.

PubMed

Abboud, Iyad Ahmed

2008-10-01

Urinary stone diseases are increasing in the Middle East. The majority of urinary stone cases are found in the northern part of the country. Stone samples taken from patients living in the Irbid area were collected from Princess Basma Hospital. The present study concentrates on the mineralogical and chemical composition of the urinary stones and on the effective environmental factors that assist in developing the different types of urinary stones. Using X-ray diffraction techniques, the mineralogical composition of the urinary stones was found to be as follows: oxalate, cholesten, and uric acid, with cystine stones occuring more frequently than the others. Cholesten and calcium oxalate stones are the most dominant types of stones. Calcium oxalate is the most common type of oxalate stone. Calcium oxalate is represented in: whewellite, wheddellite, and calcium carbonate oxalate hydrate minerals, in addition to other minerals such as brushite, ammonium phosphate, vaterite, valleriite, and bobierrite from other types of stones. Bobierrite (phosphate group) is a new mineral reported in urinary stones, and this has not been determined in any previous study worldwide. Apatite (calcium phosphate) is deduced using scanning electron microscope (SEM) images. The SEM technique determined crystal forms and systems, shapes, morphological features, and the names of the minerals forming urine stones, while optical properties are studied by polarizing microscope. X-ray fluorescence technique determined the concentrations of major and some trace elements. It revealed that Ca is the main constituent of the urinary stones, especially those composed of calcium oxalate and calcium phosphate. The concentration of trace elements was Ba = 1.57, P = 3.61, Fe = 1.78, S = 2.08, Zr = 4.63, Mo = 3.92, Cu = 1.89, Co = 1.56, and F = 4.2% and was higher in the urinary stones of Jordanian patients than in foreigners in the country. Questionnaires completed by patients suggest that the most significant factors directly effecting the formation of stones are water, climate conditions, food rich in protein and rich in different chemicals. Moreover, some drugs and diseases might also help in developing other stones.

A Common Bile Duct Stone formed by Suture Material after Open Cholecystectomy

PubMed Central

Kim, Kook-Hyun; Jang, Byung-Ik

2007-01-01

The use of non-absorbable suture materials for cystic duct ligation after cholecystectomy can expose patients to the risk of recurrent stone formation in the common bile duct (CBD). However, in Korea suture materials have rarely been found to act as a nidus for common bile duct calculus formation. Recently, we experienced a case in which suture material, that had migrated from a previous cholecystectomy site into the CBD, probably served as a nidus for common bile duct stone formation. The stone was confirmed by endoscopic retrograde cholangiopancreatography (ERCP) and removed successfully using a basket. The authors report a case of surgical suture migration and discuss its subsequent role as a stone forming nucleus within the CBD in a patient who underwent open cholecystectomy; and include a review of the literature. PMID:18309688

The "green stones" of Valtellina and Valchiavenna (central Alps, northern Italy)

NASA Astrophysics Data System (ADS)

Cavallo, Alessandro

2015-04-01

Valtellina and Val Chiavenna (Sondrio, Central Alps, northern Italy) are traditionally areas of production of building and ornamental stones (e.g. Serizzo Ghiandone, Serizzo Valmasino, San Fedelino Granite), and among these the "green stones" have a leading position. These stones had an extensive use in Lombardy, as well as abroad (e.g Switzerland). The "green stones" are related to the two mafic-ultramafic bodies of Valmalenco and Chiavenna, where the two largest quarrying districts of the Province of Sondrio are located. Until the early decades of the XX century, serpentinites (and other lithologies from Valtellina) were also extracted from the erratic boulders of Brianza (north of Milan), but at present time the law protects the few remaining boulders. The extracted and processed materials are various: serpentinites, ophicalcites, soapstones. Even the "Stone of Tresivio", used in the past in important monuments of Valtellina, could be classified among the "green stones" in a broad sense: it is a green chloritic schist with scarce and thin ferriferous calcitic veins, pertaining to the sedimentary "Servino" Formation. In recent times, the ancient quarries of this stone were rediscovered near the homonymous village, a few kilometers from Sondrio. There are also historic reports about other "green stones", used in ancient times, such as the "Stone of Grosio", a chloritic schist, and the "Bormio Prasinite". Currently the extraction and processing of "green stones" occurs mostly in Valmalenco, with 22 active serpentinite quarries and a gross volume of 70000 m3 extracted per year, with a yield of about 50%. The Malenco serpentinite (interpreted as sub-continental mantle rocks) forms a 1-2 km thick tabular body, outcropping over an area of about 170 km2, almost entirely confined within the boundaries of the valley. The antigoritic serpentinites (with variable amounts of olivine, clinopyroxene, chlorite and magnetite) are moderately up to strongly foliated, sometimes folded, and are processed in two main commercial varieties: schistose ("serpentinoscisto") and massive ("serpentino da taglio"). In Valmalenco, the extraction and processing of schistose serpentinites for the production of slabs ("piode", splitted by hand with hammer and chisel), used in roofing and flooring, dates back at least to the XIV century. From the traditional underground extraction, the quarrying activities moved to the modern open-cast extraction in the seventies. The renowned quality of the secular serpentinite roof coverings is related to the excellent physical and mechanical properties, especially the flexural strength (average values around 90-100 MPa), very low porosity and the thaw/freezing resistance. The "massive" serpentinite achieved a special place in the national and international market of ornamental stones: the several extracted varieties (Serpentino Classico, Verde Vittoria, Verde Perlato, Verde Mare, Verde Principe, Verde Torre S. Maria), in addition to the excellent technical properties (flexural strength and thermal properties) that promote specific uses, make these stones much appreciated worldwide (e.g. Bundestag in Berlin, Germany). As part of the "green stones" of Valmalenco, two currently abandoned ophicalcite quarries have been active in the recent past. The extraction and processing of soapstone ("pietra ollare" or "pietra laugera", a talc and/or chlorite rich ultramafic/mafic rock) in Valmalenco and Valchiavenna probably dates back to the Iron Age; in Valchiavenna it is documented with certainty since Roman times and the Middle Ages. The extraction and processing of soapstone peaked around the middle of the XVIII century, with a dozen quarries and about 300 workers involved, between Chiavenna and Piuro. A limited production of soapstone is still active in the municipalities of Piuro (talc-olivine-tremolite fels) and Chiesa in Valmalenco (chlorite schist), where in addition to the traditional cooking pots ("Lavecc"), there is a growing art work and gift items production. With the exception of two companies that have reached an industrial production level, the remaining 24 companies operating in Valmalenco are on an artisan level, and are grouped in the "Consorzio Artigiani Cavatori Valmalenco". The consortium, already engaged in the management of a permanent storage of explosives at the service of the quarries, promotes and subsidizes economically various initiatives aimed at the enhancement of stone products and the development of this craft. The consortium is a promoter of a cultural initiative aimed at the restoration of an underground quarry and the ancient paths of "Giovello", a historic site for the extraction and processing of serpentinite.

The effect of different screw-tightening techniques on the strain generated on an internal-connection implant superstructure. Part 2: Models created with a splinted impression technique.

PubMed

Choi, Jung-Han

2011-01-01

This study aimed to evaluate the effect of different screw-tightening sequences, torques, and methods on the strains generated on an internal-connection implant (Astra Tech) superstructure with good fit. An edentulous mandibular master model and a metal framework directly connected to four parallel implants with a passive fit to each other were fabricated. Six stone casts were made from a dental stone master model by a splinted impression technique to represent a well-fitting situation with the metal framework. Strains generated by four screw-tightening sequences (1-2-3-4, 4-3-2-1, 2-4-3-1, and 2-3-1-4), two torques (10 and 20 Ncm), and two methods (one-step and two-step) were evaluated. In the two-step method, screws were tightened to the initial torque (10 Ncm) in a predetermined screw-tightening sequence and then to the final torque (20 Ncm) in the same sequence. Strains were recorded twice by three strain gauges attached to the framework (superior face midway between abutments). Deformation data were analyzed using multiple analysis of variance at a .05 level of statistical significance. In all stone casts, strains were produced by connection of the superstructure, regardless of screw-tightening sequence, torque, and method. No statistically significant differences in superstructure strains were found based on screw-tightening sequences (range, -409.8 to -413.8 μm/m), torques (-409.7 and -399.1 μm/m), or methods (-399.1 and -410.3 μm/m). Within the limitations of this in vitro study, screw-tightening sequence, torque, and method were not critical factors for the strain generated on a well-fitting internal-connection implant superstructure by the splinted impression technique. Further studies are needed to evaluate the effect of screw-tightening techniques on the preload stress in various different clinical situations.

Accuracy of single-abutment digital cast obtained using intraoral and cast scanners.

PubMed

Lee, Jae-Jun; Jeong, Ii-Do; Park, Jin-Young; Jeon, Jin-Hun; Kim, Ji-Hwan; Kim, Woong-Chul

2017-02-01

Scanners are frequently used in the fabrication of dental prostheses. However, the accuracy of these scanners is variable, and little information is available. The purpose of this in vitro study was to compare the accuracy of cast scanners with that of intraoral scanners by using different image impression techniques. A poly(methyl methacrylate) master model was fabricated to replicate a maxillary first molar single-abutment tooth model. The master model was scanned with an accurate engineering scanner to obtain a true value (n=1) and with 2 intraoral scanners (CEREC Bluecam and CEREC Omnicam; n=6 each). The cast scanner scanned the master model and duplicated the dental stone cast from the master model (n=6). The trueness and precision of the data were measured using a 3-dimensional analysis program. The Kruskal-Wallis test was used to compare the different sets of scanning data, followed by a post hoc Mann-Whitney U test with a significance level modified by Bonferroni correction (α/6=.0083). The type 1 error level (α) was set at .05. The trueness value (root mean square: mean ±standard deviation) was 17.5 ±1.8 μm for the Bluecam, 13.8 ±1.4 μm for the Omnicam, 17.4 ±1.7 μm for cast scanner 1, and 12.3 ±0.1 μm for cast scanner 2. The differences between the Bluecam and the cast scanner 1 and between the Omnicam and the cast scanner 2 were not statistically significant (P>.0083), but a statistically significant difference was found between all the other pairs (P<.0083). The precision of the scanners was 12.7 ±2.6 μm for the Bluecam, 12.5 ±3.7 μm for the Omnicam, 9.2 ±1.2 μm for cast scanner 1, and 6.9 ±2.6 μm for cast scanner 2. The differences between Bluecam and Omnicam and between Omnicam and cast scanner 1 were not statistically significant (P>.0083), but there was a statistically significant difference between all the other pairs (P<.0083). An Omnicam in video image impression had better trueness than a cast scanner but with a similar level of precision. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Stone former urine proteome demonstrates a cationic shift in protein distribution compared to normal.

PubMed

Kolbach-Mandel, Ann M; Mandel, Neil S; Hoffmann, Brian R; Kleinman, Jack G; Wesson, Jeffrey A

2017-08-01

Many urine proteins are found in calcium oxalate stones, yet decades of research have failed to define the role of urine proteins in stone formation. This urine proteomic study compares the relative amounts of abundant urine proteins between idiopathic calcium oxalate stone forming and non-stone forming (normal) cohorts to identify differences that might correlate with disease. Random mid-morning urine samples were collected following informed consent from 25 stone formers and 14 normal individuals. Proteins were isolated from urine using ultrafiltration. Urine proteomes for each sample were characterized using label-free spectral counting mass spectrometry, so that urine protein relative abundances could be compared between the two populations. A total of 407 unique proteins were identified with the 38 predominant proteins accounting for >82% of all sample spectral counts. The most highly abundant proteins were equivalent in stone formers and normals, though significant differences were observed in a few moderate abundance proteins (immunoglobulins, transferrin, and epidermal growth factor), accounting for 13 and 10% of the spectral counts, respectively. These proteins contributed to a cationic shift in protein distribution in stone formers compared to normals (22% vs. 18%, p = 0.04). Our data showing only small differences in moderate abundance proteins suggest that no single protein controls stone formation. Observed increases in immunoglobulins and transferrin suggest increased inflammatory activity in stone formers, but cannot distinguish cause from effect in stone formation. The observed cationic shift in protein distribution would diminish protein charge stabilization, which could lead to protein aggregation and increased risk for crystal aggregation.

Diagnosis of rare inherited glyoxalate metabolic disorders through in-situ analysis of renal stones

NASA Astrophysics Data System (ADS)

Jacob, D. E.; Grohe, B.; Hoppe, B.; Beck, B. B.; Tessadri, R.

2012-04-01

The primary hyperoxalurias type I - III constitute rare autosomal-recessive inherited disorders of the human glyoxylate metabolism. By mechanisms that are ill understood progressive nephrocalcinosis and recurrent urolithiasis (kidney stone formation) often starting in early childhood, along with their secondary complications results in loss of nephron mass which progresses to end-stage renal failure over time. In the most frequent form, end-stage renal failure (ESRF) is the rule and combined liver/kidney transplantation respectively pre-emptive liver transplantation are the only causative treatment today. Hence, this contributes significantly to healthcare costs and early diagnosis is extremely important for a positive outcome for the patient. We are developing a stone-based diagnostic method by in-detail multi-methods investigation of the crystalline moiety in concert with urine and stone proteomics. Stone analysis will allow faster analysis at low-impact for the patients in the early stages of the disease. First results from combined spectroscopic (Raman, FTIR)and geochemical micro-analyses (Electron Microprobe and Laser Ablation ICP-MS) are presented here that show significant differences between stones from hyperoxaluria patients and those formed by patients without this disorder (idiopathic stones). Major differences exist in chemistry as well as in morphology and phase composition of the stones. Ca/P ratios and Mg contents differentiate between oxalate-stones from hyperoxaluria patients and idiopathic stones. Results show that also within the different subtypes of primary hyperoxaluria significant differences can be found in stone composition. These imply differences in stone formation which could be exploited for new therapeutic pathways. Furthermore, the results provide important feedback for suspected but yet unconfirmed cases of primary hyperoxaluria when used in concert with the genetic methods routinely applied.

Digital versus conventional implant impressions for edentulous patients: accuracy outcomes.

PubMed

Papaspyridakos, Panos; Gallucci, German O; Chen, Chun-Jung; Hanssen, Stijn; Naert, Ignace; Vandenberghe, Bart

2016-04-01

To compare the accuracy of digital and conventional impression techniques for completely edentulous patients and to determine the effect of different variables on the accuracy outcomes. A stone cast of an edentulous mandible with five implants was fabricated to serve as master cast (control) for both implant- and abutment-level impressions. Digital impressions (n = 10) were taken with an intraoral optical scanner (TRIOS, 3shape, Denmark) after connecting polymer scan bodies. For the conventional polyether impressions of the master cast, a splinted and a non-splinted technique were used for implant-level and abutment-level impressions (4 cast groups, n = 10 each). Master casts and conventional impression casts were digitized with an extraoral high-resolution scanner (IScan D103i, Imetric, Courgenay, Switzerland) to obtain digital volumes. Standard tessellation language (STL) datasets from the five groups of digital and conventional impressions were superimposed with the STL dataset from the master cast to assess the 3D (global) deviations. To compare the master cast with digital and conventional impressions at the implant level, analysis of variance (ANOVA) and Scheffe's post hoc test was used, while Wilcoxon's rank-sum test was used for testing the difference between abutment-level conventional impressions. Significant 3D deviations (P < 0.001) were found between Group II (non-splinted, implant level) and control. No significant differences were found between Groups I (splinted, implant level), III (digital, implant level), IV (splinted, abutment level), and V (non-splinted, abutment level) compared with the control. Implant angulation up to 15° did not affect the 3D accuracy of implant impressions (P > 0.001). Digital implant impressions are as accurate as conventional implant impressions. The splinted, implant-level impression technique is more accurate than the non-splinted one for completely edentulous patients, whereas there was no difference in the accuracy at the abutment level. The implant angulation up to 15° did not affect the accuracy of implant impressions. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

MECHANISMS OF HUMAN KIDNEY STONE FORMATION

PubMed Central

Evan, Andrew P.; Worcester, Elaine M.; Coe, Fredric L.; Williams, James; Lingeman, James E.

2014-01-01

The precise mechanisms of kidney stone formation and growth are not completely known, even though human stone disease appears to be one of the oldest diseases known to medicine. With the advent of the new digital endoscope and detailed renal physiological studies performed on well phenotyped stone formers, substantial advances have been made in our knowledge of the pathogenesis of the most common type of stone former, the idiopathic calcium oxalate stone former (ICSF) as well as nine other stone forming groups. The observations from our group on human stone formers and those of others on model systems have suggested four entirely different pathways for kidney stone formation. Calcium oxalate stone growth over sites of Randall’s plaque appear to be the primary mode of stone formation for those patients with hypercalciuria. Overgrowths off the ends of Bellini duct plugs have been noted in most stone phenotypes, do they result in a clinical stone? Micro-lith formation does occur within the lumens of dilated inner medullary collecting ducts of cystinuric stone formers and appear to be confined to this space. Lastly, cystinuric stone formers also have numerous small, oval, smooth yellow appearing calyceal stones suggestive of formation in free solution. The scientific basis for each of these four modes of stone formation are reviewed and used to explore novel research opportunities. PMID:25108546

Uric Acid Nephrolithiasis: A Systemic Metabolic Disorder

PubMed Central

Moe, Orson W.

2014-01-01

Uric acid nephrolithiasis is characteristically a manifestation of a systemic metabolic disorder. It has a prevalence of about 10% among all stone formers, the third most common type of kidney stone in the industrialized world. Uric acid stones form primarily due to an unduly acid urine; less deciding factors are hyperuricosuria and a low urine volume. The vast majority of uric acid stone formers have the metabolic syndrome, and not infrequently, clinical gout is present as well. A universal finding is a low baseline urine pH plus insufficient production of urinary ammonium buffer. Persons with gastrointestinal disorders, in particular chronic diarrhea or ostomies, and patients with malignancies with a large tumor mass and high cell turnover comprise a less common but nevertheless important subset. Pure uric acid stones are radiolucent but well visualized on renal ultrasound. A 24 h urine collection for stone risk analysis provides essential insight into the pathophysiology of stone formation and may guide therapy. Management includes a liberal fluid intake and dietary modification. Potassium citrate to alkalinize the urine to a goal pH between 6 and 6.5 is essential, as undissociated uric acid deprotonates into its much more soluble urate form. PMID:25045326

Gender Distribution of Pediatric Stone Formers

NASA Astrophysics Data System (ADS)

Novak, Thomas E.; Trock, Bruce J.; Lakshmanan, Yegappan; Gearhart, John P.; Matlaga, Brian R.

2008-09-01

Recent epidemiologic evidence suggests that the gender prevalence among adult stone-formers is changing, with an increasing incidence of stone disease among women. No similar data have ever been reported for the pediatric stone-forming population. We performed a study to define the gender distribution among pediatric stone-formers using a large-scale national pediatric database. Our findings suggest that gender distribution among stone formers varies by age with male predominance in the first decade of life shifting to female predominance in the second decade. In contrast to adults, females in the pediatric population are more commonly affected by stones than are males. The incidence of pediatric stone disease appears to be increasing at a great rate in both sexes. Further studies should build on this hypothesis-generating work and define the effects of metabolic and environmental risk factors that may influence stone risk in the pediatric patient population

Additively Manufactured Titanium and Cobalt-Chromium Implant Frameworks: Fit and Effect of Ceramic Veneering.

PubMed

Svanborg, Per; Eliasson, Alf; Stenport, Victoria

The purpose of this study was to evaluate the fit of additively manufactured cobalt-chromium and titanium and CNC-milled titanium frameworks before and after ceramic veneering. Ten stone casts simulating an edentulous maxilla provided with six abutment analogs were produced. For each stone cast, one additively manufactured cobalt-chromium framework (AM CoCr) and one titanium framework (AM Ti) were fabricated. The fit was analyzed with a coordinate measuring machine in three dimensions (x, y, and z axes) using best-fit virtual matching of center point coordinates, before and after ceramic veneering. CNC-milled titanium frameworks (CNC Ti) and earlier results from CNC-milled cobalt-chromium frameworks (CNC CoCr) were used for comparison. All frameworks presented minor misfit before and after veneering in the horizontal plane (x- and y-axes) between 2.9 and 13.5 μm and in the vertical plane (z-axis) between 1.6 and 5.4 μm. Ceramic veneering affected the fit of all groups of frameworks. Both AM Ti and AM CoCr presented significantly smaller distortion in the vertical plane compared with the CNC-milled frameworks. Implant-supported frameworks can be produced in either Ti or CoCr using either CNC milling or additive manufacturing with a fit well within the range of 20 μm in the horizontal plane and 10 μm in the vertical plane. The fit of frameworks of both materials and production techniques are affected by the ceramic veneering procedure to a small extent.

Implant Impression Techniques for the Edentulous Jaw: A Summary of Three Studies.

PubMed

Stimmelmayr, Michael; Beuer, Florian; Edelhoff, Daniel; Güth, Jan-Frederik

2016-02-01

Precise implant-supported restorations require accurate impressions. Transfer, pick-up, and splinted pick-up are commonly used techniques. Several in vitro studies have compared these impression techniques; however, all studies used mechanical evaluation methods. The purpose of this study was to compare the discrepancies of these impression techniques digitally in vitro and in vivo. Four dental implants were inserted in ten polymer mandibular models bilaterally in the regions of the first molars and canines. Three different impressions were made of each model and the models (original and stone casts) were scanned and digitized. Clinically, four implants were inserted in ten edentulous jaws; transfer and splinted pick-up impressions were made. With inspection software, discrepancies between the different impressions were calculated. The mean discrepancies in the in vitro study of the original polymer model to stone casts were 124 ± 34 μm for the transfer type, 116 ± 46 μm for the pick-up type, and 80 ± 25 μm for the splinted pick-up type, resulting in a mean discrepancy between the transfer and splinted pick-up type of 44 μm (124 - 80 μm). Clinically, the mean discrepancy between these two impression techniques was 280 μm. The differing results between the transfer and splinted pick-up techniques of in vitro and in vivo data showed the need for clinical data; however, splinted pick-up impressions seemed to produce the most precise results. © 2015 by the American College of Prosthodontists.

DEVELOPING COMPLETE ULTRASONIC MANAGEMENT OF KIDNEY STONES FOR SPACEFLIGHT.

PubMed

Simon, Julianna C; Dunmire, Barbrina; Bailey, Michael R; Sorensen, Mathew D

2016-09-01

Bone demineralization, dehydration, and stasis put astronauts at an increased risk of forming kidney stones in space. The incidence of kidney stones and the potential for a mission-critical event are expected to rise as expeditions become longer and immediate transport to Earth becomes more problematic. At the University of Washington, we are developing an ultrasound-based stone management system to detect stones with S-mode ™ ultrasound imaging, break stones with burst wave lithotripsy (BWL ™ ), and reposition stones with ultrasonic propulsion (UP ™ ) on Earth and in space. This review discusses the development and current state of these technologies, as well as integration on the flexible ultrasound system sponsored by NASA and the National Space Biomedical Research Institute.

Study of the pore structure of ceramics prepared by the slip casting method

NASA Technical Reports Server (NTRS)

Guzman, I. Y.; Dobysh, A. V.

1984-01-01

The porosity of the slip cast Si3N4 is similar to that of pressed Si3N4 formed at 2500 kg/sq cm. The porosity of cast Si oxynitride is equivalent to that of samples stressed at 10,000 kg/sq cm. Crucibles formed from these materials by slip casting have high thermal shock and corrosion resistance.

Expanding endourology for biliary stone disease: the efficacy of intracorporeal lithotripsy on refractory biliary calculi.

PubMed

Sninsky, Brian C; Sehgal, Priyanka D; Hinshaw, J Louis; McDermott, John C; Nakada, Stephen Y

2014-07-01

We evaluated the efficacy of ureteroscopic therapy (electrohydraulic lithotripsy [EHL] and intraductal laser lithotripsy [ILL]) in patients with challenging biliary stones secondary to anatomic variations resulting from a previous surgical procedure, including liver transplantation. A retrospective chart review was performed for all patients with previous surgical alteration of the gastrointestinal (GI) tract who underwent EHL or ILL via peroral or percutaneous access for choledocholithiasis by a single surgeon at our institution from 2000 to 2012. A database containing clinical and surgical variables was created, and long-term follow-up was conducted (3-138 months; median, 99 months). Thirteen patients (51.7±20.0 years; M:F, 10:3) in whom endoscopic retrograde cholangiopancreatography (ERCP), percutaneous transhepatic cholangiography (PTHC), or both failed were identified. Failure of ERCP/PTHC was because of inaccessibility of the calculi in all cases. Stone clearance was achieved in 12/13 (93%) patients; 8/12 (62%) after one procedure, and 4/12 (31%) after two procedures. One patient with biliary cast syndrome needed four interventions over 9 years. Major complications were low, with only one patient with hypotension and cholangitis that resolved with 24 hours of administration of intravenous fluids and antibiotics. Both endoscopic and percutaneous lithotripsies are effective treatments for refractory biliary calculi resulting from the post-surgical GI tract. Although a staged second procedure may be necessary in patients with significant stone burden, this is significantly better than extensive open surgery.

Experimental study on the use of spacer foils in two-step putty and wash impression procedures using silicone impression materials.

PubMed

Mann, Karsten; Davids, Andreas; Range, Ursula; Richter, Gert; Boening, Klaus; Reitemeier, Bernd

2015-04-01

The 2-step putty and wash impression technique is commonly used in fixed prosthodontics. However, cutting sluiceways to allow the light-body material to drain is time-consuming. A solution might be the use of a spacer foil. The purpose of this study was to evaluate the influence of spacer foil on the margin reproduction and dimensional accuracy of 2-step putty and wash impressions. Two methods of creating space for the wash material in a 2-step putty and wash impression were compared: the traditional cutout technique and a spacer foil. Eleven commercially available combinations of silicone impression materials were included in the study. The impressions and the cast production were carried out under standardized conditions. All casts were measured with a 3-dimensional (3D) coordinate measuring machine. Preparation margin reproduction and the diameters and spacing of the stone cast dies were measured (α=.05). The 2 methods showed significant differences (P<.05) in the reproduction of the preparation margins (complete reproduction cutout, 90% to 98%; foil, 74% to 91%). The use of a foil resulted in greater dimensional accuracy of the cast dies compared to the cutout technique. Cast dies from the cutout technique were significantly smaller than the metallic original cast (cutout median, 4.55 mm to 4.61 mm; foil median, 4.61 to 4.64). Spacing between the dies revealed only a few additional significant differences between the techniques. When spacer foils were used, dies were obtained that better corresponded to the original tooth. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

[Calcium kidney stones. Diagnostic and preventive prospects].

PubMed

Arcidiacono, T; Terranegra, A; Biasion, R; Soldati, L; Vezzoli, G

2007-01-01

Kidney stone disease is one of the main causes of hospitalization in Italy. Its prevalence increased in the last century and is probably still increasing. The pathogenesis of the disease is not known, although two main theories have been elaborated. The first hypothesizes that hydroxyapatite deposition in the interstitium of the renal papillae (Randall's plaque) precedes urinary calcium oxalate precipitation on the ulcered surface of the papilla to form a stone. The second presumes the tubular lumen of Bellini's duct to be the site where calcium-oxalate salts precipitate to form the nucleus for stone formation within the urinary tract. These pathogenetic processes may be favored by different dietary and genetic factors. The genes involved are not known, although many studies have been performed. Polymorphisms of genes coding for the vitamin D receptor, calcium-sensing receptor, interleukin-1 receptor antagonist, and urokinase were found to be associated with kidney stones, but these results have not been replicated. Different nutrients are suspected to predispose patients to calcium kidney stone disease. A high intake of animal proteins, sodium, vitamin C and oxalate has been implicated in stone formation, whereas calcium, alkalis and phytate may have a protective effect. The prevention of calcium stone formation is based on the recognition of risk factors like those already mentioned here. Furthermore, a family history of kidney stones may be useful in identifying subjects predisposed to become calcium stone formers. However, the expectations of the scientific community are turned to the advances in genetics and to the findings of genetic studies, which may provide diagnostic tools and criteria to define the risk profile of the single individual.

Vascular Calcification and Stone Disease: A New Look towards the Mechanism

PubMed Central

Yiu, Allen J.; Callaghan, Daniel; Sultana, Razia; Bandyopadhyay, Bidhan C.

2015-01-01

Calcium phosphate (CaP) crystals are formed in pathological calcification as well as during stone formation. Although there are several theories as to how these crystals can develop through the combined interactions of biochemical and biophysical factors, the exact mechanism of such mineralization is largely unknown. Based on the published scientific literature, we found that common factors can link the initial stages of stone formation and calcification in anatomically distal tissues and organs. For example, changes to the spatiotemporal conditions of the fluid flow in tubular structures may provide initial condition(s) for CaP crystal generation needed for stone formation. Additionally, recent evidence has provided a meaningful association between the active participation of proteins and transcription factors found in the bone forming (ossification) mechanism that are also involved in the early stages of kidney stone formation and arterial calcification. Our review will focus on three topics of discussion (physiological influences—calcium and phosphate concentration—and similarities to ossification, or bone formation) that may elucidate some commonality in the mechanisms of stone formation and calcification, and pave the way towards opening new avenues for further research. PMID:26185749

Mathematical model to estimate risk of calcium-containing renal stones

NASA Technical Reports Server (NTRS)

Pietrzyk, R. A.; Feiveson, A. H.; Whitson, P. A.

1999-01-01

BACKGROUND/AIMS: Astronauts exposed to microgravity during the course of spaceflight undergo physiologic changes that alter the urinary environment so as to increase the risk of renal stone formation. This study was undertaken to identify a simple method with which to evaluate the potential risk of renal stone development during spaceflight. METHOD: We used a large database of urinary risk factors obtained from 323 astronauts before and after spaceflight to generate a mathematical model with which to predict the urinary supersaturation of calcium stone forming salts. RESULT: This model, which involves the fewest possible analytical variables (urinary calcium, citrate, oxalate, phosphorus, and total volume), reliably and accurately predicted the urinary supersaturation of the calcium stone forming salts when compared to results obtained from a group of 6 astronauts who collected urine during flight. CONCLUSIONS: The use of this model will simplify both routine medical monitoring during spaceflight as well as the evaluation of countermeasures designed to minimize renal stone development. This model also can be used for Earth-based applications in which access to analytical resources is limited.

Strip casting with fluxing agent applied to casting roll

DOEpatents

Williams, R.S.; O`Malley, R.J.; Sussman, R.C.

1997-07-29

A strip caster for producing a continuous strip includes a tundish for containing a melt, a pair of horizontally disposed water cooled casting rolls and devices for electrostatically coating the outer peripheral chill surfaces of the casting rolls with a powder flux material. The casting rolls are juxtaposed relative to one another for forming a pouting basin for receiving the melt through a teeming tube thereby establishing a meniscus between the rolls for forming the strip. The melt is protected from the outside air by a non-oxidizing gas passed through a supply line to a sealing chamber. A preferred flux is boron oxide having a melting point of about 550 C. The flux coating enhances wetting of the steel melt to the casting roll and dissolves any metal oxide formed on the roll. 3 figs.

IL-6 does not predict current urolithiasis in stone formers.

PubMed

Rieder, Jocelyn M; Nisbet, Alan A; Lesser, Timothy; Franke, Ethan I; Brusky, John P; Parekh, Ashish R; Kaptein, John; Bellman, Gary C

2008-10-01

Interleukin-6 (IL-6), an inflammatory marker, has previously been found to be elevated in the urine of patients with urolithiasis. Oxalate and other stone precursors have been shown to increase IL-6 production in proximal tubular epithelial cells in vitro. We examined whether urinary IL-6 could be used as a screening test to determine current urolithiasis in individuals who are known to form urinary stones. Thirty-five adult patients with current urolithiasis demonstrated on imaging were enrolled in the study. Exclusion criteria included disease known to elevate IL-6. Each patient provided a pre-treatment urine specimen and one month after proven to be stone-free an additional urine specimen was obtained. The urinary IL-6/creatinine ratio was determined for both specimens and compared. Ten patients provided both specimens. The mean pre-operative urinary IL-6/creatinine ratio before the procedure was 1.63 pg/mL. The mean post procedure urinary IL-6/creatinine ratio after the patient was confirmed to be stone-free was 1.81 pg/mL. These were not significantly different (p=0.38). Preoperative urinary IL-6/creatinine ratio did not correlate to stone size (r=0.15) and no correlation was seen between time from treatment and stone free IL-6/creatinine ratio (r=0.48). Urinary IL-6 is not a good screening test for current urolithiasis in stone-forming individuals. It is elevated whether the stone is present or not.

Biliary bacterial factors determine the path of gallstone formation.

PubMed

Stewart, Lygia; Grifiss, J McLeod; Jarvis, Gary A; Way, Lawrence W

2006-11-01

Bacteria cause pigment gallstones and can act as a nidus for cholesterol gallstone formation. Bacterial factors that facilitate gallstone formation include beta-glucuronidase (bG), phospholipase (PhL), and slime. The current study sought to determine whether bacterial factors influence the path of gallstone formation. A total of 382 gallstones were cultured and/or examined using scanning electron microscopy (SEM). Bacteria were tested for bG and slime production. Gallstone composition was determined using infrared spectrography. Ca-palmitate presence documented bacterial PhL production. Groups were identified based upon bacterial factors present: slime and bGPhL (slime/bGPhL), bGPhL only, and slime only. Influence of bacterial stone-forming factors on gallstone composition and morphology was analyzed. Bacteria were present in 75% of pigment, 76% of mixed, and 20% of cholesterol stones. Gallstones with bGPhL producing bacteria contained more pigment (71% vs. 26%, P < .0001). The slime/bGPhL group was associated (79%) with pigment stones, bGPhL was associated (56%) with mixed stones, while slime (or none) only was associated (67%) with cholesterol stones (P < .031, all comparisons). Bacterial properties determined the path of gallstone formation. Bacteria that produced all stone-forming factors promoted pigment stone formation, while those that produced only bGPhL promoted mixed stone formation. Bacteria that only produced slime lacked the ability to generate pigment solids, and consequently were more common in the centers of cholesterol stones. This shows how bacterial characteristics may govern the process of gallstone formation.

Effect of Ferrous Additives on Magnesia Stone Hydration

NASA Astrophysics Data System (ADS)

Zimich, V.

2017-11-01

The article deals with the modification of the magnesia binder with additives containing two- and three-valent iron cations which could be embedded in the chloromagnesium stone structure and also increase the strength from 60 MPa in a non-additive stone to 80MPa, water resistance from 0.58 for clear stone to 0.8 and reduce the hygroscopicity from 8% in the non-additive stone to 2% in the modified chloromagnesium stone. It is proposed to use the iron hydroxide sol as an additive in the quantities of up to 1% of the weight of the binder. The studies were carried out using the modern analysis methods: the differentialthermal and X-ray phase analysis. The structure was studied with an electron microscope with an X-ray microanalyzer. A two-factor plan-experiment was designed which allowed constructing mathematical models characterizing the influence of variable factors, such as the density of the zatcher and the amount of sol in the binder, on the basic properties of the magnesian stone. The result of the research was the magnesia stone with the claimed properties and formed from minerals characteristic for magnesian materials as well as additionally formed from amachenite and goethite. It has been established that a highly active iron hydroxide sol the ion sizes of which are commensurate with magnesium ions is actively incorporated into the structure of pentahydroxychloride and magnesium hydroxide changing the habit of crystals compacting the structure of the stone and changing its hygroscopicity.

BIOCHEMICAL EFFECTS IN NORMAL AND STONE FORMING RATS TREATED WITH THE RIPE KERNEL JUICE OF PLANTAIN (MUSA PARADISIACA)

PubMed Central

Devi, V. Kalpana; Baskar, R.; Varalakshmi, P.

1993-01-01

The effect of Musa paradisiaca stem kernel juice was investigated in experimental urolithiatic rats. Stone forming rats exhibited a significant elevation in the activities of two oxalate synthesizing enzymes - Glycollic acid oxidase and Lactate dehydrogenase. Deposition and excretion of stone forming constituents in kidney and urine were also increased in these rats. The enzyme activities and the level of crystalline components were lowered with the extract treatment. The extract also reduced the activities of urinary alkaline phosphatase, lactate dehydrogenase, r-glutamyl transferase, inorganic pyrophosphatase and β-glucuronidase in calculogenic rats. No appreciable changes were noticed with leucine amino peptidase activity in treated rats. PMID:22556626

Factors influencing bladder stone formation in patients with spinal cord injury.

PubMed

Favazza, Terry; Midha, Meena; Martin, Jessicca; Grob, B Mayer

2004-01-01

Bladder stones that form in patients with spinal cord injury (SCI) can cause significant morbidity. This study sought to analyze factors associated with bladder stone formation to determine which patients might be at increased risk to develop bladder stones. A review of 56 SCI patients treated for bladder calculi over a 10-year period at a single institution was performed. These patients were compared with a control population of general SCI patients known to be stone free. The factors compared were patient age, duration of injury, level of injury, completeness of injury, method of bladder management, and the presence of documented urinary tract infections with urease-producing organisms. All patients with stones were male and had a median age of 58.5 years. The median level of injury was C6, the median time since injury was 21 years, 66% had complete injuries, 68% managed their bladders with indwelling catheters or suprapubic tubes, and 83% had a history of infections with urease-producing organisms. When compared with the control group, patients forming bladder stones were older (P = 0.03), were more likely to have indwelling catheters (P < 0.0001), had a history of infections with urease-producing organisms (P = 0.04), and had complete injuries (P = 0.018). This information can be used to identify patients who have an increased risk of bladder stones and measures can be taken to reduce their incidence and morbidity.

Renal stone composition does not affect the outcome of percutaneous nephrolithotomy in children.

PubMed

Kaygısız, Onur; Türegün, Fethi Ahmet; Satar, Nihat; Özen, Ender; Toksöz, Serdar; Doğan, Hasan Serkan; Pişkin, Mehmet Mesut; İzol, Volkan; Sarıkaya, Şaban; Kılıçarslan, Hakan; Çiçek, Tufan; Öztürk, Ahmet; Tekgül, Serdar; Önal, Bülent

2018-05-14

We sought to investigate the association between renal stone composition and percutaneous nephrolithotomy outcomes in pediatric patients and define the characterization of the stone composition. The data of 1157 children who underwent percutaneous nephrolithotomy between 1991 and 2012 were retrieved from the multicenter database of the Turkish Pediatric Urology Society. The study population comprised 359 children (160 girls, 199 boys) with stone analyses. Patients were divided into five groups according to the stone composition [group 1: calcium oxalate; group 2: calcium phosphate; group 3: infection stones (magnesium ammonium phosphate, ammonium urate); group 4: cystine; group 5: uric acid, xanthine stones]. Patient characteristics, perioperative, postoperative, and stone characteristics were compared considering the stone composition. There were no significant differences between the groups concerning age, sex, side involved, preoperative hematocrit levels, and solitary renal unit. Patients with cystine stones were more likely to have a history of stone treatment. Groups 2 and 5 had mostly solitary stones. However, group 3 had staghorn stone more often, and group 4 frequently had multiple stones. Overall stone-free rate (79.4%) was similar among the groups. Although stone composition was related to blood transfusion and prolonged operative and fluoroscopy screening times on univariate analysis, it was not a significant predictor of them on multivariate analysis. Stone composition was not a predictor of outcomes of pediatric percutaneous nephrolithotomy. However, cystine and infection stones, which are larger and filled multiple calyxes due to the nature of stone forming, were more challenging cases that need multiple tracts.

Influence of rotational speed of centrifugal casting process on appearance, microstructure, and sliding wear behaviour of Al-2Si cast alloy

NASA Astrophysics Data System (ADS)

Mukunda, P. G.; Shailesh, Rao A.; Rao, Shrikantha S.

2010-02-01

Although the manner in which the molten metal flows plays a major role in the formation of the uniform cylinder in centrifugal casting, not much information is available on this topic. The flow in the molten metal differs at various rotational speeds, which in turn affects the final casting. In this paper, the influence of the flow of molten metal of hyper eutectic Al-2Si alloys at various rotational speeds is discussed. At an optimum speed of 800 rpm, a uniform cylinder was formed. For the rotational speeds below and above these speeds, an irregular shaped casting was formed, which is mainly due to the influence of melt. Primary á-Al particles were formed in the tube periphery at low rotational speed, and their sizes and shapes were altered with changes in rotational speeds. The wear test for the inner surface of the casting showed better wear properties for the casting prepared at the optimum speed of rotation.

Metabolic Characteristics and Risks Associated with Stone Recurrence in Korean Young Adult Stone Patients.

PubMed

Kang, Ho Won; Seo, Sung Pil; Kim, Won Tae; Kim, Yong-June; Yun, Seok-Joong; Kim, Wun-Jae; Lee, Sang-Cheol

2017-08-01

The aim of this study was to assess the metabolic characteristics and risks of stone recurrence in young adult stone patients in Korea. The medical records of 1532 patients presenting with renal or ureteric stones at our stone clinic between 1994 and 2015 were retrospectively reviewed. Patients were grouped according to age (young adult, 18-29 years; intermediate onset, 30-59 years; old age, ≥60 years) at first presentation, and measurements of clinicometabolic characteristics and risks of stone recurrence were compared. Overall, excretion of urinary stone-forming substances was highest in the intermediate onset group, followed by the young adult and old age groups. Importantly, excretion of urinary citrate was lowest in the young adult group. Kaplan-Meier analyses identified a significant difference between the three age groups in terms of stone recurrence (log rank test, p < 0.001). Multivariate Cox regression analyses revealed that age at first stone presentation was an independent risk factor for stone recurrence. Urinary citrate excretion was an independent risk factor for stone recurrence in young adult stone patients. Younger age (18-29 years) at first stone presentation was a significant risk factor for stone recurrence, and urinary citrate excretion was an independent risk factor affecting recurrence in this group. Metabolic evaluation and potassium citrate therapy should be considered for young adult stone patients to prevent recurrence.

Strip casting with fluxing agent applied to casting roll

DOEpatents

Williams, Robert S.; O'Malley, Ronald J.; Sussman, Richard C.

1997-01-01

A strip caster (10) for producing a continuous strip (24) includes a tundish (12) for containing a melt (14), a pair of horizontally disposed water cooled casting rolls (22) and devices (29) for electrostatically coating the outer peripheral chill surfaces (44) of the casting rolls with a powder flux material (56). The casting rolls are juxtaposed relative to one another for forming a pouting basin (18) for receiving the melt through a teeming tube (16) thereby establishing a meniscus (20) between the rolls for forming the strip. The melt is protected from the outside air by a non-oxidizing gas passed through a supply line (28) to a sealing chamber (26). A preferred flux is boron oxide having a melting point of about 550.degree. C. The flux coating enhances wetting of the steel melt to the casting roll and dissolves any metal oxide formed on the roll.

Effect of bionic coupling units' forms on wear resistance of gray cast iron under dry linear reciprocating sliding condition

NASA Astrophysics Data System (ADS)

Pang, Zuobo; Zhou, Hong; Xie, Guofeng; Cong, Dalong; Meng, Chao; Ren, Luquan

2015-07-01

In order to get close to the wear form of guide rails, the homemade linear reciprocating wear testing machine was used for the wear test. In order to improve the wear-resistance of gray cast iron guide rail, bionic coupling units of different forms were manufactured by a laser. Wear behavior of gray-cast-iron with bionic-coupling units has been studied under dry sliding condition at room temperature using the wear testing machine. The wear resistance was evaluated by means of weight loss measurement and wear morphology. The results indicated that bionic coupling unit could improve the wear resistance of gray cast iron. The wear resistance of gray cast iron with reticulation bionic coupling unit is the best. When the load and speed changed, reticulation bionic coupling unit still has excellent performance in improving the wear resistance of gray cast iron.

Armenian Khatchkar (Stone Cross) Carved in 1308.

ERIC Educational Resources Information Center

Hacobian, Mossik

This booklet introduces students to a unique form of stone sculpture made by Armenian artists for over twelve centuries, the khatchkar, or stone cross. The document is part of a series of seven instructional materials dealing with the history and culture of Armenian Americans. It contains a reading on khatchkars as symbols of faith for eternity, a…

Sculpture: Stone Shapes, Art: 6683.08.

ERIC Educational Resources Information Center

Dubocq, Edward R.

This elective course for grades 7-12 was created with a three fold purpose: 1) to create in the student an awareness of the effect of sculptural forms on his environment; 2) to introduce the student to an appreciation of stone sculpture; and 3) to further enhance the artistic abilities of the student through sculpting in stone. Course content…

Reproduction accuracy of articulator mounting with an arbitrary face-bow vs. average values-a controlled, randomized, blinded patient simulator study.

PubMed

Ahlers, M Oliver; Edelhoff, Daniel; Jakstat, Holger A

2018-06-21

The benefit from positioning the maxillary casts with the aid of face-bows has been questioned in the past. Therefore, the aim of this study was to investigate the reliability and validity of arbitrary face-bow transfers compared to a process solely based on the orientation by means of average values. For optimized validity, the study was conducted using a controlled, randomized, anonymized, and blinded patient simulator study design. Thirty-eight undergraduate dental students were randomly divided into two groups; both groups were applied to both methods, in opposite sequences. Investigated methods were the transfer of casts using an arbitrary face-bow in comparison to the transfer using average values based on Bonwill's triangle and the Balkwill angle. The "patient" used in this study was a patient simulator. All casts were transferred to the same individual articulator, and all the transferred casts were made using type IV special hard stone plaster; for the attachment into the articulator, type II plaster was used. A blinded evaluation was performed based on three-dimensional measurements of three reference points. The results are presented three-dimensionally in scatterplots. Statistical analysis indicated a significantly smaller variance (Student's t test, p < 0.05) for the transfer using a face-bow, applicable for all three reference points. The use of an arbitrary face-bow significantly improves the transfer reliability and hence the validity. To simulate the patient situation in an individual articulator correctly, casts should be transferred at least by means of an arbitrary face-bow.

Salvaged castings and methods of salvaging castings with defective cast cooling bumps

DOEpatents

Johnson, Robert Alan; Schaeffer, Jon Conrad; Lee, Ching-Pang; Abuaf, Nesim; Hasz, Wayne Charles

2002-01-01

Castings for gas turbine parts exposed on one side to a high-temperature fluid medium have cast-in bumps on an opposite cooling surface side to enhance heat transfer. Areas on the cooling surface having defectively cast bumps, i.e., missing or partially formed bumps during casting, are coated with a braze alloy and cooling enhancement material to salvage the part.

Cast erosion from the cleaning of debris after the use of a cast trimmer.

PubMed

Hansen, Paul A; Beatty, Mark W

2017-02-01

Whether using tap water to rinse off debris will make a clinical difference to the surface detail of a gypsum cast is unknown. In addition, how best to remove debris from the cast is unknown. The purpose of this in vitro study was to evaluate the efficiency of different methods of cleaning a gypsum cast after trimming and the effect of short-term exposure to tap water on the surface quality of the cast. A die fitting American National Standards Institute/American Dental Association specification 25 (International Standards Organization specification 6873) for dental gypsum products was embedded in a Dentoform with the machined lines positioned at the same level as the occlusal surface of the posterior teeth. A flat plate was used to ensure that the plane of occlusion for the die was at the same position as the posterior teeth. Forty polyvinyl siloxane impressions of the Dentoform were made and poured with vacuum-mixed improved Type IV dental stone. Each cast was inspected for the accurate reproduction of the lines. The base of the 2-stage pour was trimmed with a cast trimmer with water, and surface debris was removed by rinsing by hand under tap water for 10 seconds, by brushing the cast with a soft toothbrush for 10 seconds, or by resoaking the cast and using a soft camel hair brush in slurry water for 10 seconds. The amount of debris was evaluated on a scale of 1 to 4, and the quality of the 20-μm line was evaluated on a scale of 1 to 4 under ×15 magnification. The nonparametric Kruskal-Wallis ranks test was used to identify significant differences among the different cleaning methods (α=.05). Results of the Kruskal-Wallis and Kruskal-Wallis Z-value tests demonstrated that all cleaning methods produced cleaner casts than were observed for uncleansed controls (P<.001), but no differences in debris removal were found among the different cleaning methods (.065≤P≤.901). The ability to see the quality of a 20-μm line (P=.974) was not statistically different among the groups. Rinsing the cast under flowing tap water and brushing, or hand washing under flowing tap water, or using a soft camel hair brush in slurry water for 10 seconds had no noticeable effects on the quality of a 20-μm line, and all 3 methods resulted in a clean cast. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

A comparison of the accuracy of polyether, polyvinyl siloxane, and plaster impressions for long-span implant-supported prostheses.

PubMed

Hoods-Moonsammy, Vyonne J; Owen, Peter; Howes, Dale G

2014-01-01

The purpose of this study was to compare the capacity of different impression materials to accurately reproduce the positions of five implant analogs on a master model by comparing the resulting cast with the stainless steel master model. The study was motivated by the knowledge that distortions can occur during impression making and the pouring of casts and that this distortion may produce inaccuracies of subsequent restorations, especially long-span castings for implant superstructures. The master model was a stainless steel model with five implant analogs. The impression materials used were impression plaster (Plastogum, Harry J Bosworth), a polyether (Impregum Penta, 3M ESPE), and two polyvinyl siloxane (PVS) materials (Aquasil Monophase and Aquasil putty with light-body wash, Dentsply). Five impressions were made with each impression material and cast in die stone under strictly controlled laboratory conditions. The positions of the implants on the master model, the impression copings, and the implant analogs in the subsequent casts were measured using a coordinate measuring machine that measures within 4 μm of accuracy. Statistical analyses indicated that distortion occurred in all of the impression materials, but inconsistently. The PVS monophase material reproduced the master model most accurately. Although there was no significant distortion between the impressions and the master model or between the impressions and their casts, there were distortions between the master model and the master casts, which highlighted the cumulative effects of the distortions. The polyether material proved to be the most reliable in terms of predictability. The impression plaster displayed cumulative distortion, and the PVS putty with light body showed the least reliability. Some of the distortions observed are of clinical significance and likely to contribute to a lack of passive fit of any superstructure. The inaccuracy of these analog materials and procedures suggested that greater predictability may lie in digital technology.

Evaluation and medical management of kidney stones in children.

PubMed

Tasian, Gregory E; Copelovitch, Lawrence

2014-11-01

We review the current literature on the diagnostic evaluation and dietary and pharmacological management of children with nephrolithiasis. We searched MEDLINE(®), Embase(®) and the Cochrane Library from their inceptions to March 2014 for published articles in English on kidney stones and therapy in children 0 to 18 years old. Based on review of the titles and abstracts, 110 of the 1,014 articles (11%) were potentially relevant to the diagnostic evaluation and medical management of nephrolithiasis in children. We summarized this literature and drew on studies performed in adult populations to augment areas in which no studies of sufficient quality have been performed in children, and to highlight areas in need of research. During the last 25 years the incidence of nephrolithiasis in children has increased by approximately 6% to 10% annually and is now 50 per 100,000 adolescents. Kidney stones that form during childhood have a similar composition to those that form in adulthood. Approximately 75% to 80% of stones are composed of predominantly calcium oxalate, 5% to 10% are predominantly calcium phosphate, 10% to 20% are struvite and 5% are pure uric acid. The recurrence rate of nephrolithiasis in patients with stones that form during childhood is poorly defined. Ultrasound should be used as the initial imaging study to evaluate children with suspected nephrolithiasis, with noncontrast computerized tomography reserved for those in whom ultrasound is nondiagnostic and the suspicion of nephrolithiasis remains high. Current treatment strategies for children with kidney stone disease are based largely on extrapolation of studies performed in adult stone formers and single institution cohort or case series studies of children. Tamsulosin likely increases the spontaneous passage of ureteral stones in children. Increased water intake and reduction of salt consumption should be recommended for all children with a history of kidney stones. Potassium citrate is a potentially effective medication for children with calcium oxalate stones and concomitant hypocitraturia, as well as children with uric acid stones. However, long-term compliance with therapy and the effect on decreasing stone recurrence in children are unknown. Based largely on efficacy in adult populations, thiazide diuretics should be considered in the treatment of children with calcium based stones and persistent hypercalciuria refractory to reductions in salt intake. The incidence of kidney stone disease in children is increasing, yet few randomized clinical trials or high quality observational studies have assessed whether dietary or pharmacological interventions decrease the recurrence of kidney stones in children. Collaborative efforts and randomized clinical trials are needed to determine the efficacy and effectiveness of alternative treatments for children with nephrolithiasis, particularly those with calcium oxalate stones and concomitant hypercalciuria and hypocitraturia. Additional areas in need of study are the optimal length of time for a trial of stone passage in children, the cost-effectiveness of medical expulsive therapy vs analgesics alone, and the size and location of stones for which medical expulsive therapy is most effective. Copyright © 2014 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

Bone Genes in the Kidney of Stone Formers

NASA Astrophysics Data System (ADS)

Evan, Andrew P.; Bledsoe, Sharon B.

2008-09-01

Intraoperative papillary biopsies from kidneys of idiopathic-calcium oxalate stone formers (ICSF) have revealed a distinct pattern of mineral deposition in the interstitium of the renal papilla. The earliest sites of these deposits, termed Randall's plaque, are found in the basement membrane of thin loops of Henle and appear to spread into the surrounding interstitium down to the papillary epithelium. Recent studies show kidney stones of ICSF patients grow attached to the renal papilla and at sites of Randall's plaque. Together these observations suggest that plaque formation may be the critical step in stone formation. In order to control plaque formation and thereby reduce future kidney stone development, the mechanism of plaque deposition must be understood. Because the renal papilla has unique anatomical features similar to bone and the fact that the interstitial deposits of ICSF patients are formed of biological apatite, this paper tests the hypothesis that sites of interstitial plaque form as a result of cell-mediated osteoblast-like activity.

Extracorporeal shock wave lithotripsy of proximal and distal ureteral stones.

PubMed

Pettersson, B; Tiselius, H G

1988-01-01

Extracorporeal shock wave lithotripsy (ESWL) was used for treatment of 105 patients with ureteral stones. There were 77 stones in the upper part of the ureter, i.e. above the pelvic brim, and 28 in the lower part, i.e. below the sacroiliac joint. Successful fragmentation was attained in 101 (96%). In 93% of the patients with stones in the upper ureter and in 100% with stones in the lower ureter the fragments were eliminated completely. In 87% of the patients with stones in the upper ureter, a ureteral catheter was introduced under local anesthesia but without fluoroscopic control. It was thereby possible to remove 30% of the stones from the ureter to the kidney. For the remaining stones, saline was infused through the catheter during ESWL. For patients with stones in the lower part of the ureter, a ureteral catheter was passed in 79% and saline infused during treatment. Whereas some form of anesthesia was used for treatment of all upper ureteral stones, 89% of the treatments for lower ureteral stones were performed without anesthesia. Auxiliary procedures after ESWL were limited to four ureteral catheter manipulations for distal stones. Four proximal stones which remained unaffected by ESWL had to be treated by open surgery (3 stones) or percutaneous surgery (1 stone). Of 82 ureteric stones treated in situ the success fragmentation rate was 95%. The average number of ESWL sessions was 1.04 for both proximal and distal ureteral stones.

Comparing the efficacy of metronome beeps and stepping stones to adjust gait: steps to follow!

PubMed

Bank, Paulina J M; Roerdink, Melvyn; Peper, C E

2011-03-01

Acoustic metronomes and visual targets have been used in rehabilitation practice to improve pathological gait. In addition, they may be instrumental in evaluating and training instantaneous gait adjustments. The aim of this study was to compare the efficacy of two cue types in inducing gait adjustments, viz. acoustic temporal cues in the form of metronome beeps and visual spatial cues in the form of projected stepping stones. Twenty healthy elderly (aged 63.2 ± 3.6 years) were recruited to walk on an instrumented treadmill at preferred speed and cadence, paced by either metronome beeps or projected stepping stones. Gait adaptations were induced using two manipulations: by perturbing the sequence of cues and by imposing switches from one cueing type to the other. Responses to these manipulations were quantified in terms of step-length and step-time adjustments, the percentage correction achieved over subsequent steps, and the number of steps required to restore the relation between gait and the beeps or stepping stones. The results showed that perturbations in a sequence of stepping stones were overcome faster than those in a sequence of metronome beeps. In switching trials, switching from metronome beeps to stepping stones was achieved faster than vice versa, indicating that gait was influenced more strongly by the stepping stones than the metronome beeps. Together these results revealed that, in healthy elderly, the stepping stones induced gait adjustments more effectively than did the metronome beeps. Potential implications for the use of metronome beeps and stepping stones in gait rehabilitation practice are discussed.

Aging and Curing Temperature Effects on Compressive Strength of Mortar Containing Lime Stone Quarry Dust and Industrial Granite Sludge.

PubMed

Amin, Muhammad Nasir; Khan, Kaffayatullah; Saleem, Muhammad Umair; Khurram, Nauman; Niazi, Muhammad Umar Khan

2017-06-11

In this study, the researchers investigated the potential use of locally available waste materials from the lime stone quarry and the granite industry as a partial replacement of cement. Quarry sites and granite industry in the eastern province of Saudi Arabia produces tons of powder wastes in the form of quarry dust (QD) and granite sludge (GS), respectively, causing serious environmental problems along with frequent dust storms in the area. According to ASTM C109, identical 50-mm3 specimens were cast throughout this study to evaluate the compressive strength development of mortars (7, 28 and 91 days) containing these waste materials. Experimental variables included different percentage replacement of cement with waste materials (GS, QD), fineness of GS, various curing temperatures (20, 40 and 60 °C as local normal and hot environmental temperatures) and curing moisture (continuously moist and partially moist followed by air curing). Finally, the results of mortar containing waste materials were compared to corresponding results of control mortar (CM) and mortar containing fly ash (FA). The test results indicated that under normal curing (20 °C, moist cured), the compressive strength of mortar containing the different percentage of waste materials (QD, GS, FA and their combinations) remained lower than that of CM at all ages. However, the compressive strength of mortar containing waste materials slightly increased with increased fineness of GS and significantly increased under high curing temperatures. It was recommended that more fineness of GS be achieved to use its high percentage replacement with cement (30% or more) incorporating local environmental conditions.

Aging and Curing Temperature Effects on Compressive Strength of Mortar Containing Lime Stone Quarry Dust and Industrial Granite Sludge

PubMed Central

Amin, Muhammad Nasir; Khan, Kaffayatullah; Saleem, Muhammad Umair; Khurram, Nauman; Niazi, Muhammad Umar Khan

2017-01-01

In this study, the researchers investigated the potential use of locally available waste materials from the lime stone quarry and the granite industry as a partial replacement of cement. Quarry sites and granite industry in the eastern province of Saudi Arabia produces tons of powder wastes in the form of quarry dust (QD) and granite sludge (GS), respectively, causing serious environmental problems along with frequent dust storms in the area. According to ASTM C109, identical 50-mm3 specimens were cast throughout this study to evaluate the compressive strength development of mortars (7, 28 and 91 days) containing these waste materials. Experimental variables included different percentage replacement of cement with waste materials (GS, QD), fineness of GS, various curing temperatures (20, 40 and 60 °C as local normal and hot environmental temperatures) and curing moisture (continuously moist and partially moist followed by air curing). Finally, the results of mortar containing waste materials were compared to corresponding results of control mortar (CM) and mortar containing fly ash (FA). The test results indicated that under normal curing (20 °C, moist cured), the compressive strength of mortar containing the different percentage of waste materials (QD, GS, FA and their combinations) remained lower than that of CM at all ages. However, the compressive strength of mortar containing waste materials slightly increased with increased fineness of GS and significantly increased under high curing temperatures. It was recommended that more fineness of GS be achieved to use its high percentage replacement with cement (30% or more) incorporating local environmental conditions. PMID:28772999

Adhesion Casting In Low Gravity

NASA Technical Reports Server (NTRS)

Noever, David A.; Cronise, Raymond J.

1996-01-01

Adhesion casting in low gravity proposed as technique for making new and improved materials. Advantages of low-gravity adhesion casting, in comparison with adhesion casting in normal Earth gravity, comes from better control over, and greater uniformity of, thicknesses of liquid films that form on and adhere to solid surfaces during casting.

What can the microstructure of stones tell us?

PubMed Central

Williams, James C.; Worcester, Elaine; Lingeman, James E.

2016-01-01

How stones are retained within the kidney while small in size is still not fully understood. In this paper we show two examples of how stones are retained during early growth: One is growth on Randall’s (interstitial) plaque, and the other is growth on mineral that has formed as a luminal plug in a terminal collecting duct. These two mechanisms of stone retention during early growth have distinctive morphologic features that can be seen by methods that show the microscopic structure of the stones. Stones growing on Randall’s plaque display an apatite region that is typically not large in size (less than 0.5 mm across) but which usually shows luminal spaces, which are signs of its origin in the connective tissue of the papilla. Stones growing on ductal plugs also show attachment to a piece of apatite, but the apatite regions are typically larger (often >1 mm long and >0.5 mm wide), and they are solid, without spaces running through them. We propose that knowing the mechanisms of stone retention during early stone formation could allow for better treatment of stone diseases. PMID:27913855

Chronic Kidney Disease in Kidney Stone Formers

PubMed Central

Krambeck, Amy E.; Lieske, John C.

2011-01-01

Summary Recent population studies have found symptomatic kidney stone formers to be at increased risk for chronic kidney disease (CKD). Although kidney stones are not commonly identified as the primary cause of ESRD, they still may be important contributing factors. Paradoxically, CKD can be protective against forming kidney stones because of the substantial reduction in urine calcium excretion. Among stone formers, those with rare hereditary diseases (cystinuria, primary hyperoxaluria, Dent disease, and 2,8 dihydroxyadenine stones), recurrent urinary tract infections, struvite stones, hypertension, and diabetes seem to be at highest risk for CKD. The primary mechanism for CKD from kidney stones is usually attributed to an obstructive uropathy or pyelonephritis, but crystal plugs at the ducts of Bellini and parenchymal injury from shockwave lithotripsy may also contribute. The historical shift to less invasive surgical management of kidney stones has likely had a beneficial impact on the risk for CKD. Among potential kidney donors, past symptomatic kidney stones but not radiographic stones found on computed tomography scans were associated with albuminuria. Kidney stones detected by ultrasound screening have also been associated with CKD in the general population. Further studies that better classify CKD, better characterize stone formers, more thoroughly address potential confounding by comorbidities, and have active instead of passive follow-up to avoid detection bias are needed. PMID:21784825

Effects of microgravity on renal stone risk assessment

NASA Technical Reports Server (NTRS)

Pietrzyk, R. A.; Pak, C. Y. C.; Cintron, N. M.; Whitson, P. A.

1992-01-01

Physiologic changes induced during human exposure to the microgravity environment of space may contribute to an increased potential for renal stone formation. Renal stone risk factors obtained 10 days before flight and immediately after return to earth indicated that calcium oxalate and uric acid stone-forming potential was increased after space flights of 4-10 days. These data describe the need for examining renal stone risk during in-flight phases of space missions. Because of limited availability of space and refrigerated storage on spacecraft, effective methods must be developed for collecting urine samples in-flight and for preserving (or storing) them at temperatures and under conditions commensurate with mission constraints.

Development of a two-stage in vitro model system to investigate the mineralization mechanisms involved in idiopathic stone formation: stage 1-biomimetic Randall's plaque using decellularized porcine kidneys.

PubMed

Lovett, Archana C; Khan, Saeed R; Gower, Laurie B

2018-05-18

Idiopathic calcium oxalate (CaOx) stone formers form stones that are commonly attached to calcium phosphate (CaP) deposits in the renal tissue, known as Randall's plaques (RP). Plaques are suggested to originate in the renal tubular basement membrane, where they exhibit a morphology of concentrically laminated apatitic spherules, while in the interstitial regions, the collagen fibrils and vesicles become mineralized. We hypothesize that these minerals might form by non-classical crystallization mechanisms, such as via amorphous precursors, some of which might originate from a polymer-induced liquid-precursor (PILP) process. Thus, our goal is to identify mineralogical 'signatures' of various stone formation mechanisms. To do this for idiopathic CaOx stones, we are developing a two-stage model system of CaP-CaOx composite stones, consisting of stage (1) CaP mineralized plaque, followed by stage (2) CaOx overgrowth into a stone. For the studies presented here, decellularized porcine kidneys were mineralized with CaP using polyaspartic acid or the protein osteopontin (OPN) to induce the PILP process and create biomimetic RP. Analysis of the PILP-mineralized tissues shows features that resemble the native plaques, including mineral spherules and collagen with intrafibrillar mineral. In contrast, the classical crystallization produced large apatitic spherulites, which is a very different morphology, but one which is also found in some stones. An alternative hypothesis regarding Randall's plaque, and if or when it becomes pathological, is discussed.

Cystine Stone Formers Have Impaired Health-Related Quality of Life Compared with Noncystine Stone Formers: A Case-Referent Study Piloting the Wisconsin Stone Quality of Life Questionnaire Among Patients with Cystine Stones.

PubMed

Streeper, Necole M; Wertheim, Margaret L; Nakada, Stephen Y; Penniston, Kristina L

2017-04-01

Cystinuria is a rare cause of urolithiasis. Affected patients have an earlier onset and more aggressive disease than patients with other stone etiologies. We assessed the health-related quality of life (HRQOL) of cystine stone-forming patients using the disease-specific Wisconsin Stone Quality of Life questionnaire (WISQOL). Cystine patients treated in our stone clinics (n = 12) completed the WISQOL; information about medical and stone histories was gathered. Patients were matched with noncystine stone formers (n = 12) for gender, age, and comorbidities. In addition, a second control group (n = 90), also from our institution and consisting of mixed calcium stone formers, was included. WISQOL responses were compared between groups. Cystine patients had significantly lower total WISQOL scores than noncystine patients. Compared with noncystine stone formers, cystine stone formers also had lower HRQOL scores for subscales (domains) related to social impact, emotional impact, disease impact, and vitality (p ≤ 0.04 for all). On specific items, cystine patients reported significantly more sleep problems (p = 0.02), more bother with nocturia (p = 0.03), and feeling tired or fatigued (p = 0.02). Among those with current stones, cystine patients scored lower than noncystine patients for total score and in two of four domains. Using a stone-specific questionnaire, patients with cystine stones have lower HRQOL compared with noncystine stone formers. Identifying and addressing specific areas of decrement in patients with cystine stones may improve disease management and patients' HRQOL.

The osteopontin-controlled switching of calcium oxalate monohydrate morphologies in artificial urine provides insights into the formation of papillary kidney stones.

PubMed

Langdon, Aaron; Grohe, Bernd

2016-10-01

The protein osteopontin (OPN) plays an important role in preventing the formation of calcium oxalate monohydrate (COM) kidney stones. To gain insight into these mechanisms, crystallization was induced by addition of human kidney OPN to artificial urine (ionic strength comparable to urine; without citrate), and the OPN-COM interaction studied using a combination of scanning electron (SEM) and confocal microscopy. By SEM, we found that increasing OPN concentrations formed large monoclinic penetration twins (no protein added) and, at higher concentrations (1-, 2μg/ml OPN), super and hyper twins with crystal habits not found in previous studies. For instance, the hyper twins indicate well-facetted gearwheel-like habits with "teeth" developed in all crystallographic directions. At OPN concentrations ≥2μg/ml, a switching to small dumbbell-shaped COM habits with fine-textured surfaces occurred. Confocal microscopy of these dumbbells indicates protein incorporation in almost the entire crystal structure (in contrast to facetted COM), proposing a threshold concentration of ∼2μg/ml OPN for the facetted to the non-facetted habit transformation. Both the gearwheel-like and the dumbbell-shaped habit are again found side-by-side (presumably triggered by OPN concentration gradients within the sample) in in-vitro formed conglomerates, which resemble cross-sections of papillary kidney stones. The abrupt transformation from facetted to non-facetted habits and the unique compliance of the two in-vitro formed habits with the two main morphologies found in papillary kidney stones propose that OPN is a main effector in direct stone-forming processes. Moreover, stone structures which exhibit these two morphologies side-by-side might serve as a novel indicator for OPN concentrations surrounding those structures. Copyright © 2016 Elsevier B.V. All rights reserved.

Renal Stone Risk During Space Flight: Assessment and Countermeasure Validation

NASA Technical Reports Server (NTRS)

Whitson, P. A.; Sams, C. F.; Jones, J. A.; Pietrzke, R. A.; Nelman-Gonzalez, M. A.; Hudson, E. K.

2007-01-01

NASA has focused its future on exploration class missions including the goal of returning to the moon and landing on Mars. With these objectives, humans will experience an extended exposure to the harsh environment of microgravity and the associated negative effects on all the physiological systems of the body. Exposure to microgravity affects human physiology and results in changes to the urinary chemical composition during and after space flight. These changes are associated with an increased risk of renal stone formation. The development of a renal stone would have health consequences for the crewmember and negatively impact the success of the mission. As of January 2007, 15 known symptomatic medical events consistent with urinary calculi have been experienced by 13 U.S. astronauts and Russian cosmonauts. Previous results from both MIR and Shuttle missions have demonstrated an increased risk for renal stone formation. These data have shown decreased urine volume, urinary pH and citrate levels and increased urinary calcium. Citrate, an important urinary inhibitor of calcium-containing renal stones binds with calcium in the urine, thereby reducing the amount of calcium available to form calcium oxalate stones. Urinary citrate also prevents calcium oxalate crystals from aggregating into larger crystals and into renal stones. In addition, citrate makes the urine less acidic which inhibits the development of uric acid stones. Potassium citrate supplementation has been successfully used to treat patients who have formed renal stones. The evaluation of potassium citrate as a countermeasure has been performed during the ISS Expeditions 3-6, 8, 11-13 and is currently in progress during the ISS Expedition 14 mission. Together with the assessment of stone risk and the evaluation of a countermeasure, this investigation provides an educational opportunity to all crewmembers. Individual urinary biochemical profiles are generated and the risk of stone formation is estimated. Increasing fluid intake is recommended to all crewmembers. These results can be used to lower the risk for stone formation through lifestyle, diet changes or therapeutic administration to minimize the risk for stone development. With human presence in microgravity a continuing presence and exploration class missions being planned, maintaining the health and welfare of all crewmembers is critical to the exploration of space.

Treatment and prevention of kidney stones: an update.

PubMed

Frassetto, Lynda; Kohlstadt, Ingrid

2011-12-01

The incidence of nephrolithiasis (kidney stones) is rising worldwide, especially in women and with increasing age. Kidney stones are associated with chronic kidney disease. Preventing recurrence is largely specific to the type of stone (e.g., calcium oxalate, calcium phosphate, cystine, struvite [magnesium ammonium phosphate]), and uric acid stones); however, even when the stone cannot be retrieved, urine pH and 24-hour urine assessment provide information about stone-forming factors that can guide prevention. Medications, such as protease inhibitors, antibiotics, and some diuretics, increase the risk of some types of kidney stones, and patients should be counseled about the risks of using these medications. Managing diet, medication use, and nutrient intake can help prevent the formation of kidney stones. Obesity increases the risk of kidney stones. However, weight loss could undermine prevention of kidney stones if associated with a high animal protein intake, laxative abuse, rapid loss of lean tissue, or poor hydration. For prevention of calcium oxalate, cystine, and uric acid stones, urine should be alkalinized by eating a diet high in fruits and vegetables, taking supplemental or prescription citrate, or drinking alkaline mineral waters. For prevention of calcium phosphate and struvite stones, urine should be acidified; cranberry juice or betaine can lower urine pH. Antispasmodic medications, ureteroscopy, and metabolic testing are increasingly being used to augment fluid and pain medications in the acute management of kidney stones.

Protein content of human apatite and brushite kidney stones: significant correlation with morphologic measures.

PubMed

Pramanik, Rocky; Asplin, John R; Jackson, Molly E; Williams, James C

2008-10-01

Apatite and brushite kidney stones share calcium and phosphate as their main inorganic components. We tested the hypothesis that these stone types differ in the amount of proteins present in the stones. Intact stones were intensively analyzed by microcomputed tomography (micro CT) for both morphology (including the volume of voids, i.e., space devoid of X-ray dense material) and mineral type. To extract all proteins present in kidney stones in soluble form we developed a three-step extraction procedure using the ground stone powder. Apatite stones had significantly higher levels of total protein content and void volume compared to brushite stones. The void volume was highly correlated with the total protein contents in all stones (r2 = 0.61, P < 0.0001), and brushite stones contained significantly fewer void regions and proteins than did apatite stones (3.2 +/- 4.5% voids for brushite vs. 10.8 +/- 11.2% for apatite, P < 0.005; 4.1 +/- 1.6% protein for brushite vs. 6.0 +/- 2.4% for apatite, P < 0.03). Morphological observations other than void volume did not correlate with protein content of stones, and neither did the presence or absence of minor mineral components. Our results show that protein content of brushite and apatite stones is higher than that was previously thought, and also suggest that micro CT-visible void regions are related to the presence of protein.

Renal Stone Risk During Space Flight

NASA Technical Reports Server (NTRS)

Whitson, Peggy A.; Pietrzyk, Robert A.; Sams, Clarence F.; Pak, Charles Y. C.; Jones, Jeffrey A.

1999-01-01

Space flight produces a number of metabolic and physiological changes in the crewmembers exposed to microgravity. Following launch, body fluid volumes, electrolyte levels, and bone and muscle undergo changes as the human body adapts to the weightless environment. Changes in the urinary chemical composition may lead to the potentially serious consequences of renal stone formation. Previous data collected immediately after space flight indicate changes in the urine chemistry favoring an increased risk of calcium oxalate and uric acid stone formation (n = 323). During short term Shuttle space flights, the changes observed include increased urinary calcium and decreased urine volume, pH and citrate resulting in a greater risk for calcium oxalate and brushite stone formation (n = 6). Results from long duration Shuttle/Mir missions (n = 9) followed a similar trend and demonstrated decreased fluid intake and urine volume and increased urinary calcium resulting in a urinary environment saturated with the calcium stone-forming salts. The increased risk occurs rapidly upon exposure to microgravity, continues throughout the space flight and following landing. Dietary factors, especially fluid intake, or pharmacologic intervention can significantly influence the urinary chemical composition. Increasing fluid intake to produce a daily urine output of 2 liters/day may allow the excess salts in the urine to remain in solution, crystals formation will not occur and a renal stone will not develop. Results from long duration crewmembers (n = 2) who had urine volumes greater than 2.5 L/day minimized their risk of renal stone formation. Also, comparisons of stone-forming risk in short duration crewmembers clearly identified greater risk in those who produced less than 2 liters of urine/day. However, hydration and increased urine output does not correct the underlying calcium excretion due to bone loss and only treats the symptoms and not the cause of the increased urinary salts. Dietary modification and promising pharmacologic treatments may also be used to reduce the potential risk for renal stone formation. Potassium citrate is being used clinically to increase the urinary inhibitor levels to minimize the development of crystals and the growth of renal stones. Bisphosphonates are a class of drugs recently shown to help in patients with osteoporosis by inhibiting the loss of bones in elderly patients. This drug could potentially prevent the bone loss observed in astronauts and thereby minimize the increase in urinary calcium and reduce the risk for renal stone development. Results of NASA's renal stone risk assessment program clearly indicate that exposure to microgravity changes the urinary chemical environment such that there is an increased risk for supersaturation of stone-forming salts, including calcium oxalaie and brushite. These studies have indicated specific avenues for development of countermeasures for the increased renal stone risk observed during and following space flight. Increased hydration and implementation of pharmacologic countermeasures should largely mitigate the in-flight risk of renal stones.

Comparison of reconstructed rapid prototyping models produced by 3-dimensional printing and conventional stone models with different degrees of crowding.

PubMed

Wan Hassan, Wan Nurazreena; Yusoff, Yusnilawati; Mardi, Noor Azizi

2017-01-01

Rapid prototyping models can be reconstructed from stereolithographic digital study model data to produce hard-copy casts. In this study, we aimed to compare agreement and accuracy of measurements made with rapid prototyping and stone models for different degrees of crowding. The Z Printer 450 (3D Systems, Rock Hill, SC) reprinted 10 sets of models for each category of crowding (mild, moderate, and severe) scanned using a structured-light scanner (Maestro 3D, AGE Solutions, Pisa, Italy). Stone and RP models were measured using digital calipers for tooth sizes in the mesiodistal, buccolingual, and crown height planes and for arch dimension measurements. Bland-Altman and paired t test analyses were used to assess agreement and accuracy. Clinical significance was set at ±0.50 mm. Bland-Altman analysis showed the mean bias of measurements between the models to be within ±0.15 mm (SD, ±0.40 mm), but the 95% limits of agreement exceeded the cutoff point of ±0.50 mm (lower range, -0.81 to -0.41 mm; upper range, 0.34 to 0.76 mm). Paired t tests showed statistically significant differences for all planes in all categories of crowding except for crown height in the moderate crowding group and arch dimensions in the mild and moderate crowding groups. The rapid prototyping models were not clinically comparable with conventional stone models regardless of the degree of crowding. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Guaifenesin stone matrix proteomics: a protocol for identifying proteins critical to stone formation.

PubMed

Kolbach-Mandel, A M; Mandel, N S; Cohen, S R; Kleinman, J G; Ahmed, F; Mandel, I C; Wesson, J A

2017-04-01

Drug-related kidney stones are a diagnostic problem, since they contain a large matrix (protein) fraction and are frequently incorrectly identified as matrix stones. A urine proteomics study patient produced a guaifenesin stone during her participation, allowing us to both correctly diagnose her disease and identify proteins critical to this drug stone-forming process. The patient provided three random midday urine samples for proteomics studies; one of which contained stone-like sediment with two distinct fractions. These solids were characterized with optical microscopy and Fourier transform infrared spectroscopy. Immunoblotting and quantitative mass spectrometry were used to quantitatively identify the proteins in urine and stone matrix. Infrared spectroscopy showed that the sediment was 60 % protein and 40 % guaifenesin and its metabolite guaiacol. Of the 156 distinct proteins identified in the proteomic studies, 49 were identified in the two stone-components with approximately 50 % of those proteins also found in this patient's urine. Many proteins observed in this drug-related stone have also been reported in proteomic matrix studies of uric acid and calcium containing stones. More importantly, nine proteins were highly enriched and highly abundant in the stone matrix and 8 were reciprocally depleted in urine, suggesting a critical role for these proteins in guaifenesin stone formation. Accurate stone analysis is critical to proper diagnosis and treatment of kidney stones. Many matrix proteins were common to all stone types, but likely not related to disease mechanism. This protocol defined a small set of proteins that were likely critical to guaifenesin stone formation based on their high enrichment and high abundance in stone matrix, and it should be applied to all stone types.

Black and brown pigment gallstones differ in microstructure and microcomposition.

PubMed

Malet, P F; Takabayashi, A; Trotman, B W; Soloway, R D; Weston, N E

1984-01-01

The two subtypes of pigment gallstones, black and brown stones, differ in chemical composition and pathogenesis. We examined a black bilirubinate stone and a black phosphate stone (which represented opposite ends of the compositional spectrum of black noncarbonate stones), a black carbonate stone, and a brown pigment stone using scanning electron microscopy and microchemical techniques to determine if stone microstructure and microcomposition reflected different patterns of formation. The cross-sectional surfaces of the black bilirubinate and black phosphate stones were smooth and homogenous. Electron probe microanalysis demonstrated high concentrations of sulfur and copper in the center of the black bilirubinate stone; sulfur was in a low valence state consistent with disulfide linkages in proteins. The brown stone was rough-surfaced with lamellated bands on cross-section. The lighter-colored bands in this stone contained virtually all of the detected calcium palmitate, while the darker sections contained much more calcium bilirubinate. Plasma oxygen etching demonstrated a network of protein interdigitating with calcium bilirubinate salts in the black bilirubinate and black phosphate stones but not in the black carbonate or brown stones. Argon ion etching demonstrated that calcium bilirubinate was in a closely packed rod-shaped arrangement in all three black stones but not in the brown stone. We conclude that the marked differences in structure and composition between the black noncarbonate and brown pigment gallstones support the hypothesis that the two major pigment gallstone types form by different mechanisms. In addition, the layered structures of the black carbonate and brown stones suggest that stone growth is affected by cyclic changes in biliary composition.

Bioremediation of weathered-building stone surfaces.

PubMed

Webster, Alison; May, Eric

2006-06-01

Atmospheric pollution and weathering of stone surfaces in urban historic buildings frequently results in disfigurement or damage by salt crust formation (often gypsum), presenting opportunities for bioremediation using microorganisms. Conventional techniques for the removal of these salt crusts from stone have several disadvantages: they can cause colour changes; adversely affect the movement of salts within the stone structure; or remove excessive amounts of the original surface. Although microorganisms are commonly associated with detrimental effects to the integrity of stone structures, there is growing evidence that they can be used to treat this type of stone deterioration in objects of historical and cultural significance. In particular, the ability and potential of different microorganisms to either remove sulfate crusts or form sacrificial layers of calcite that consolidate mineral surfaces have been demonstrated. Current research suggests that bioremediation has the potential to offer an additional technology to conservators working to restore stone surfaces in heritage buildings.

Assessment of kidney stone and prevalence of its chemical compositions.

PubMed

Pandeya, A; Prajapati, R; Panta, P; Regmi, A

2010-09-01

Kidney stone analysis is the test done on the stone which cause problems when they block the flow of urine through or out of the kidneys. The stones cause severe pain and are also associated with morbidity and renal damage. There is also no clear understanding on the relative metabolic composition of renal calculi. Hence, the study is aimed to find out the chemical composition of it which can guide treatment and give information that may prevent more stones from forming. The study was carried out on the stones that had been sent to the department of Biochemistry (n = 99; M = 61; F = 38; Mean age: 33.6 +/- 14.4 years) Approximately 98.9% of stones were composed of oxalate, 95.9% of Calcium, 85.8% of phosphate, 62.6% of Urate, 46.4% of Ammonium and very few percentages of Carbonate.

Process for forming a long gas turbine engine blade having a main wall with a thin portion near a tip

DOEpatents

Campbell, Christian X; Thomaidis, Dimitrios

2014-05-13

A process is provided for forming an airfoil for a gas turbine engine involving: forming a casting of a gas turbine engine airfoil having a main wall and an interior cavity, the main wall having a wall thickness extending from an external surface of the outer wall to the interior cavity, an outer section of the main wall extending from a location between a base and a tip of the airfoil casting to the tip having a wall thickness greater than a final thickness. The process may further involve effecting movement, using a computer system, of a material removal apparatus and the casting relative to one another such that a layer of material is removed from the casting at one or more radial portions along the main wall of the casting.

Research Of The Influence Of Reftinskii SDPP’S Ash On The Processes Of Cement Stone’S Structure Forming

NASA Astrophysics Data System (ADS)

Zimakova, G. A.; Solonina, V. A.; Zelig, M. P.

2017-01-01

The article describes the experimental research of cement stone. Cement stone forming involves highly dispersive mineral additive - ground ash. It is stated that the substitution of some part of cement with activated ash leaves cement strength high. This is possible due to the activity of ash in structure forming processes. Activation of ash provides the increase in its puzzolanic activity, complete hydration processes. it is stated that ash grinding leads to a selective crystallization hydrated neoformations. Their morthology is different on outer and inner surfaces of ash spheres. The usage of ash can provide cement economy on condition that rheological characteristics of concrete stay constant. Besides, the usage of ash will improve physical and mechanic characteristics of cement stone and concrete.

Biotechnology

NASA Image and Video Library

2002-07-31

Renal stones are never convenient, but they are a particular concern for astronauts who have limited access to treatment during flight. Researchers are examining how earthbound preventions for renal stone formation work in flight, ensuring missions are not ended prematurely due to this medical condition. The micrograph shows calcium oxalate crystals in urine. These small crystals can develop to form renal stones. Principal Investigator: Dr. Peggy Whitson, NASA Johnson Space Center, Houston, TX.

Calcium Tartrate Tetrahydrate, Case Report of a Novel Human Kidney Stone.

PubMed

Kleinguetl, Colin; Williams, James C; Ibrahim, Samar A; Daudon, Michel; Bird, Erin T; El Tayeb, Marawan M

2017-01-01

Background: Calcium tartrate tetrahydrate has been reported as the main mineral in urinary stones in rats that have significant tartrate in their diet, but in humans, there has been only one mention of calcium tartrate stones in the form of bladder stone, and that case was in Africa. Case Presentation: Patient is a 34-year-old Caucasian male who presented with typical symptoms of nephrolithiasis. CT abd/pelvis (renal stone protocol) revealed a 2 cm nonobstructing stone of the right renal pelvis. Patient underwent an uncomplicated right percutaneous nephrolithotomy and was noted to be stone free after surgery. Stone analysis was difficult with regard to determining composition, but was finally identified as calcium tartrate tetrahydrate. Conclusion: This was an unusual case, as this is the first recorded case of a calcium tartrate tetrahydrate outside of Africa. This type of stone had only been mainly described in rat models with dl- bitartrate in their diet. Our patient was an otherwise healthy, relatively muscular individual with no obvious source for this stone other than a vitamin and amino acid supplement that he takes regularly that contains l-carnitine (as tartrate) and choline (as bitartrate and citrate). The prevalence of this stone type is presently unknown, as stone analysis laboratories have not had the ability to recognize it. Although a connection between the supplement and stone formation is conjecture at this time, we believe this necessitates further investigation.

Incidental kidney stones: a single center experience with kidney donor selection

PubMed Central

Kim, Irene K.; Tan, Jane C.; Lapasia, Jessica; Elihu, Arvand; Busque, Stephan; Melcher, Marc L.

2014-01-01

The presence of kidney stones has been a relative contraindication for living donation. With the widespread use of more sensitive imaging techniques as part of the routine living donor workup, kidney stones are more frequently detected, and their clinical significance in this setting is largely unknown. Records from 325 potential kidney donors who underwent MRA or CT-angiography were reviewed; 294 proceeded to donation. The prevalence of kidney stones found incidentally during donor evaluation was 7.4% (24 of 325). Sixteen donors with stones proceeded with kidney donation. All incidental calculi were nonobstructing and small (median 2 mm; range 1–9 mm). Eleven recipients were transplanted with allografts containing stones. One recipient developed symptomatic nephrolithasis after transplantation. This recipient was found to have newly formed stones secondary to hyperoxaluria, suggesting a recipient-driven propensity for stone formation. The remaining ten recipients have stable graft function, postoperative ultrasound negative for nephrolithiasis, and no sequelae from stones. No donor developed symptomatic nephrolithiasis following donation. Judicious use of allografts with small stones in donors with normal metabolic studies may be acceptable, and careful follow-up in recipients of such allografts is warranted. PMID:22168332

Evaluation of a Three-Dimensional Stereophotogrammetric Method to Identify and Measure the Palatal Surface Area in Children With Unilateral Cleft Lip and Palate.

PubMed

De Menezes, Marcio; Cerón-Zapata, Ana Maria; López-Palacio, Ana Maria; Mapelli, Andrea; Pisoni, Luca; Sforza, Chiarella

2016-01-01

To assess a three-dimensional (3D) stereophotogrammetric method for area delimitation and evaluation of the dental arches of children with unilateral cleft lip and palate (UCLP). Obtained data were also used to assess the 3D changes occurring in the maxillary arch with the use of orthopedic therapy prior to rhinocheiloplasty and before the first year of life. Within the collaboration between the Università degli Studi di Milano (Italy) and the University CES of Medellin (Colombia), 96 palatal cast models obtained from neonatal patients with UCLP were analyzed using a 3D stereophotogrammetric imaging system. The area of the minor and greater cleft segments on the digital dental cast surface were delineated by the visualization tool of the stereophotogrammetric software and then examined. "Trueness" of the measurements, as well as systematic and random errors between operators' tracings ("precision") were calculated. The method gave area measurements close to true values (errors lower than 2%), without systematic measurement errors for tracings by both interoperators and intraoperators (P > .05). Statistically significant differences (P < .05) were noted for alveolar segment and time. Maxillary segments have the potential for growth during presurgical orthopedic treatment in the early neonatal period. The cleft segment delimitation on digital dental casts and area measurements by the 3D stereophotogrammetric system revealed an accurate (true and precise) method for evaluating the stone casts of newborn patients with UCLP.

Experimental Studies of Heat-Transfer Behavior at a Casting/Water-Cooled-Mold Interface and Solution of the Heat-Transfer Coefficient

NASA Astrophysics Data System (ADS)

Zeng, Y. D.; Wang, F.

2018-02-01

In this paper, we propose an experimental model for forming an air gap at the casting/mold interface during the solidification process of the casting, with the size and formation time of the air gap able to be precisely and manually controlled. Based on this model, experiments of gravity casting were performed, and on the basis of the measured temperatures at different locations inside the casting and the mold, the inverse analysis method of heat transfer was applied to solve for the heat-transfer coefficient at the casting/mold interface during the solidification process. Furthermore, the impacts of the width and formation time of the air gap on the interface heat-transfer coefficient (IHTC) were analyzed. The results indicate that the experimental model succeeds in forming an air gap having a certain width at any moment during solidification of the casting, thus allowing us to conveniently and accurately study the impact of the air gap on IHTC using the model. In addition, the casting/mold IHTC is found to first rapidly decrease as the air gap forms and then slowly decrease as the solidification process continues. Moreover, as the width of the air gap and the formation time of the air gap increase, the IHTC decreases.

Effect of vitamin C supplements on urinary oxalate and pH in calcium stone-forming patients.

PubMed

Baxmann, Alessandra Calábria; De O G Mendonça, Claudia; Heilberg, Ita Pfeferman

2003-03-01

The contribution of ascorbate to urinary oxalate is controversial. The present study aimed to determine whether urinary oxalate and pH may be affected by vitamin C supplementation in calcium stone-forming patients. Forty-seven adult calcium stone-forming patients received either 1 g (N=23) or 2 g (N=24) of vitamin C supplement for 3 days and 20 healthy subjects received 1 g. A 24-hour urine sample was obtained both before and after vitamin C for calcium, oxalate, magnesium, citrate, sodium, potassium, and creatinine determination. The Tiselius index was used as a calcium oxalate crystallization index. A spot fasting morning urine sample was also obtained to determine the urinary pH before and after vitamin C. Fasting urinary pH did not change after 1 g (5.8 +/- 0.6 vs. 5.8 +/- 0.7) or 2 g vitamin C (5.8 +/- 0.8 vs. 5.8 +/- 0.7). A significant increase in mean urinary oxalate was observed in calcium stone-forming patients receiving either 1 g (50 +/- 16 vs. 31 +/- 12 mg/24 hours) or 2 g (48 +/- 21 vs. 34 +/- 12 mg/24 hours) of vitamin C and in healthy subjects (25 +/- 12 vs. 39 +/- 13 mg/24 hours). A significant increase in mean Tiselius index was observed in calcium stone-forming patients after 1 g (1.43 +/- 0.70 vs. 0.92 +/- 0.65) or 2 g vitamin C (1.61 +/- 1.05 vs. 0.99 +/- 0.55) and in healthy subjects (1.50 +/- 0.69 vs. 0.91 +/- 0.46). Ancillary analyses of spot urine obtained after vitamin C were performed in 15 control subjects in vessels with or without ethylenediaminetetraacetic acid (EDTA) with no difference in urinary oxalate between them (28 +/- 23 vs. 26 +/- 21 mg/L), suggesting that the in vitro conversion of ascorbate to oxalate did not occur. These data suggest that vitamin C supplementation may increase urinary oxalate excretion and the risk of calcium oxalate crystallization in calcium stone-forming patients.

Evaluation of a 3D stereophotogrammetric technique to measure the stone casts of patients with unilateral cleft lip and palate.

PubMed

Sforza, Chiarella; De Menezes, Marcio; Bresciani, Elena; Cerón-Zapata, Ana M; López-Palacio, Ana M; Rodriguez-Ardila, Myriam J; Berrio-Gutiérrez, Lina M

2012-07-01

To assess a three-dimensional stereophotogrammetric method for palatal cast digitization of children with unilateral cleft lip and palate. As part of a collaboration between the University of Milan (Italy) and the University CES of Medellin (Colombia), 96 palatal cast models obtained from neonatal patients with unilateral cleft lip and palate were obtained and digitized using a three-dimensional stereophotogrammetric imaging system. Three-dimensional measurements (cleft width, depth, length) were made separately for the longer and shorter cleft segments on the digital dental cast surface between landmarks, previously marked. Seven linear measurements were computed. Systematic and random errors between operators' tracings, and accuracy on geometric objects of known size were calculated. In addition, mean measurements from three-dimensional stereophotographs were compared statistically with those from direct anthropometry. The three-dimensional method presented good accuracy error (<0.9%) on measuring geometric objects. No systematic errors between operators' measurements were found (p > .05). Statistically significant differences (p < 5%) were noted for different methods (caliper versus stereophotogrammetry) for almost all distances analyzed, with mean absolute difference values ranging between 0.22 and 3.41 mm. Therefore, rates for the technical error of measurement and relative error magnitude were scored as moderate for Ag-Am and poor for Ag-Pg and Am-Pm distances. Generally, caliper values were larger than three-dimensional stereophotogrammetric values. Three-dimensional stereophotogrammetric systems have some advantages over direct anthropometry, and therefore the method could be sufficiently precise and accurate on palatal cast digitization with unilateral cleft lip and palate. This would be useful for clinical analyses in maxillofacial, plastic, and aesthetic surgery.

CENTRIFUGAL CASTING MACHINE

DOEpatents

Shuck, A.B.

1958-04-01

A device is described that is specifically designed to cast uraniumn fuel rods in a vacuunn, in order to obtain flawless, nonoxidized castings which subsequently require a maximum of machining or wastage of the expensive processed material. A chamber surrounded with heating elements is connected to the molds, and the entire apparatus is housed in an airtight container. A charge of uranium is placed in the chamber, heated, then is allowed to flow into the molds While being rotated. Water circulating through passages in the molds chills the casting to form a fine grained fuel rod in nearly finished form.

Long-term oxidation of candidate cast iron and stainless steel exhaust system alloys from 650 to 800 °C in air with water vapor

DOE PAGES

Brady, Michael P.; Muralidharan, Govindarajan; Leonard, Donovan .; ...

2014-08-29

Here, the oxidation behavior of SiMo cast iron, Ni-resist D 5S cast iron, cast chromia-forming austenitic stainless steels of varying Cr/Ni content based on CF8C plus, HK, and HP, and a developmental cast alumina-forming austenitic (AFA) stainless steel of interest for diesel exhaust system components were studied for up to 5000 h at 650-800 °C in air with 10% H 2O. At 650 °C, the Ni-resist D5S exhibited moderately better oxidation resistance than did the SiMo cast iron. However, the D5S suffered from oxide scale spallation issues at 700 °C and higher, whereas the oxide scales formed on SiMo castmore » iron remained adherent from 700-800 °C despite oxide scales hundreds of microns thick. The oxidation of the SiMo cast iron exhibited unusual temperature dependence, with periods of slower oxidation kinetics at 750-800 °C compared to 650-700 °C due to continuous silica-rich scale formation at the higher temperatures. The oxidation of the cast chromia-forming austenitics trended with the level of Cr and Ni additions, with small mass losses consistent with Cr oxy-hydroxide volatilization processes for the higher 25Cr/25-35Ni HK and HP type alloys, and transition to rapid Fe-base oxide formation and scale spallation in the lower 19Cr/12Ni CF8C plus type alloy. In contrast, small positive mass changes consistent with protective alumina scale formation were observed for the cast AFA alloy under all conditions studied. Implications of these findings for diesel exhaust system components are discussed.« less

Effect of molybdenum, vanadium, boron on mechanical properties of high chromium white cast iron in as-cast condition

NASA Astrophysics Data System (ADS)

Nurjaman, F.; Sumardi, S.; Shofi, A.; Aryati, M.; Suharno, B.

2016-02-01

In this experiment, the effect of the addition carbide forming elements on high chromium white cast iron, such as molybdenum, vanadium and boron on its mechanical properties and microstructure was investigated. The high chromium white cast iron was produced by casting process and formed in 50 mm size of grinding balls with several compositions. Characterization of these grinding balls was conducted by using some testing methods, such as: chemical and microstructure analysis, hardness, and impact test. From the results, the addition of molybdenum, vanadium, and boron on high chromium white cast iron provided a significant improvement on its hardness, but reduced its toughness. Molybdenum induced fully austenitic matrix and Mo2C formation among eutectic M7C3 carbide. Vanadium was dissolved in the matrix and carbide. While boron was played a role to form fine eutectic carbide. Grinding balls with 1.89 C-13.1 Cr-1.32 Mo-1.36 V-0.00051 B in as-cast condition had the highest hardness, which was caused by finer structure of eutectic carbide, needle like structure (upper bainite) matrix, and martensite on its carbide boundary.

Influence of storage methods on the surface roughness of tissue conditioners.

PubMed

Hong, Guan; Li, YingAi; Maeda, Takeshi; Mizumachi, Wataru; Sadamori, Shinsuke; Hamada, Taizo; Murata, Hiroshi

2008-03-01

The purpose of this study was to compare the influence of three kinds of storage methods on surface roughness of tissue conditioners. Four commercial tissue conditioners (GC Soft Liner, Softone, Fictioner, and Hydro-Cast) were used in this study. Five samples of each material were stored in distilled water, air, and a denture cleanser (Polident). Mean surface roughness (R(a)) values of dental stone casts made from the tissue conditioners were measured after 0, 1, 3, 7, and 14 days of immersion using a profilometer. Significant differences in the R(a) values of the specimens were found among the three storage methods. The values of R(a) significantly increased with increase in immersion time for each storage method, except for the materials stored in air. It was found that the materials stored in air showed the most stable and lowest values of R(a). Results obtained suggested that a tissue conditioner exhibited smooth and minimal change in surface roughness with time when stored in air than in distilled water and denture cleanser.

Gypsum accumulation on carbonate stone

USGS Publications Warehouse

McGee, E.S.; Mossotti, V.G.

1992-01-01

The accumulation of gypsum on carbonate stone has been investigated through exposure of fresh samples of limestone and marble at monitored sites, through examination of alteration crusts from old buildings and through laboratory experiments. Several factors contribute to gypsum accumulation on carbonate stone. Marble or limestone that is sheltered from direct washing by rain in an urban environment with elevated pollution levels is likely to accumulate a gypsum crust. Crust development may be enhanced if the stone is porous or has an irregular surface area. Gypsum crusts are a surficial alteration feature; gypsum crystals form at the pore opening-air interface, where evaporation is greatest.

Energy Consumption of Die Casting Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jerald Brevick; clark Mount-Campbell; Carroll Mobley

2004-03-15

Molten metal processing is inherently energy intensive and roughly 25% of the cost of die-cast products can be traced to some form of energy consumption [1]. The obvious major energy requirements are for melting and holding molten alloy in preparation for casting. The proper selection and maintenance of melting and holding equipment are clearly important factors in minimizing energy consumption in die-casting operations [2]. In addition to energy consumption, furnace selection also influences metal loss due to oxidation, metal quality, and maintenance requirements. Other important factors influencing energy consumption in a die-casting facility include geographic location, alloy(s) cast, starting formmore » of alloy (solid or liquid), overall process flow, casting yield, scrap rate, cycle times, number of shifts per day, days of operation per month, type and size of die-casting form of alloy (solid or liquid), overall process flow, casting yield, scrap rate, cycle times, number of shifts per day, days of operation per month, type and size of die-casting machine, related equipment (robots, trim presses), and downstream processing (machining, plating, assembly, etc.). Each of these factors also may influence the casting quality and productivity of a die-casting enterprise. In a die-casting enterprise, decisions regarding these issues are made frequently and are based on a large number of factors. Therefore, it is not surprising that energy consumption can vary significantly from one die-casting enterprise to the next, and within a single enterprise as function of time.« less

The wonderful soapstone

NASA Astrophysics Data System (ADS)

Heldal, Tom

2017-04-01

The bedrock of Norway is predominantly composed of hard and crystalline rocks, difficult to use for our ancestors. But soapstone became the exception. Fairly evenly distributed throughout the country, soapstone resources were available to most Norwegians. And they used it. For everyday utensils, the small things needed in a household. Fishing hooks and weights, loom weights, spinning wheels and oil lamps. But also other types of items were produced, including ceremonial club or mace heads from the Mesolithic and Neolithic figurines of animals. Since soapstone is both heat resistant and easy to carve, it became the preferred material from the Bronze Age onwards for making moulds for casting metals. These properties were also key in the evolution of one of the most peculiar outfield industries in Norway: producing cooking vessels from soapstone, lasting more than 2000 years, from 500 BCE. Soapstone vessels became widely used and obviously popular among the rich as the poor. There are hundreds of quarries in Norway carrying the typical signatures from the extraction of cooking pot blanks: circular depressions in the rock face from where the blanks were extracted. Some places half-finished blanks still remains, like a bulge on the rock. When Christianity came to Norway in the 11th Century, the Norwegians had to learn something new, namely to construct elaborate stone buildings, preferably churches. In several parts of Norway, soapstone became the main stone material in the construction of churches and monasteries. In spite of its softness, the rock proved to be both durable and strong, and did not crack in a fire. The medieval builders represent the heydays of stone-made crafts in Norway. Stone masons travelled through Europe, offering their skills, and some made the foundation for a rich Norwegian stone-building tradition. Many known soapstone quarries were transformed to industrial scaled production sites of blocks for ashlars, columns and sculptures. After the black death in the mid-14th Century, stone crafting skills deteriorated. The reformation in 1537 made the medieval churches targets for greedy noblemen who needed stones for their castles and homes. However, a new tradition of using soapstone gradually grew, this time for using the stone for fire places and chimneys. Old quarries were re-employed for the new purpose. This tradition has actually lasted until the present time, and modern Norwegians highly appreciate the quality and energy efficiency of well-crafted ovens and fire places. The green economy may find further needs for soapstone. For instance, the excellent heat storage capacities can be interesting for energy-efficient housing.

A comparative study of the microstructures observed in statically cast and continuously cast Bi-In-Sn ternary eutectic alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sengupta, S.; Soda, H.; McLean, A.

2000-01-01

A ternary eutectic alloy with a composition of 57.2 pct Bi, 24.8 pct In, and 18 pct Sn was continuously cast into wire of 2 mm diameter with casting speeds of 14 and 79 mm/min using the Ohno Continuous Casting (OCC) process. The microstructures obtained were compared with those of statically cast specimens. Extensive segregation of massive Bi blocks, Bi complex structures, and tin-rich dendrites was found in specimens that were statically cast. Decomposition of {radical}Sn by a eutectoid reaction was confirmed based on microstructural evidence. Ternary eutectic alloy with a cooling rate of approximately 1 C/min formed a doublemore » binary eutectic. The double binary eutectic consisted of regions of BiIn and decomposed {radical}Sn in the form of a dendrite cell structure and regions of Bi and decomposed {radical}Sn in the form of a complex-regular cell. The Bi complex-regular cells, which are a ternary eutectic constituent, existed either along the boundaries of the BiIn-decomposed {radical}Sn dendrite cells or at the front of elongated dendrite cell structures. In the continuously cast wires, primary Sn dendrites coupled with a small Bi phase were uniformly distributed within the Bi-In alloy matrix. Neither massive Bi phase, Bi complex-regular cells, no BiIn eutectic dendrite cells were observed, resulting in a more uniform microstructure in contrast to the heavily segregated structures of the statically cast specimens.« less

Optimization of Melt Treatment for Austenitic Steel Grain Refinement

NASA Astrophysics Data System (ADS)

Lekakh, Simon N.; Ge, Jun; Richards, Von; O'Malley, Ron; TerBush, Jessica R.

2017-02-01

Refinement of the as-cast grain structure of austenitic steels requires the presence of active solid nuclei during solidification. These nuclei can be formed in situ in the liquid alloy by promoting reactions between transition metals (Ti, Zr, Nb, and Hf) and metalloid elements (C, S, O, and N) dissolved in the melt. Using thermodynamic simulations, experiments were designed to evaluate the effectiveness of a predicted sequence of reactions targeted to form precipitates that could act as active nuclei for grain refinement in austenitic steel castings. Melt additions performed to promote the sequential precipitation of titanium nitride (TiN) onto previously formed spinel (Al2MgO4) inclusions in the melt resulted in a significant refinement of the as-cast grain structure in heavy section Cr-Ni-Mo stainless steel castings. A refined as-cast structure consisting of an inner fine-equiaxed grain structure and outer columnar dendrite zone structure of limited length was achieved in experimental castings. The sequential of precipitation of TiN onto Al2MgO4 was confirmed using automated SEM/EDX and TEM analyses.

Idiopathic hypercalciuria and formation of calcium renal stones

PubMed Central

Coe, Fredric L.; Worcester, Elaine M.; Evan, Andrew P.

2018-01-01

The most common presentation of nephrolithiasis is idiopathic calcium stones in patients without systemic disease. Most stones are primarily composed of calcium oxalate and form on a base of interstitial apatite deposits, known as Randall’s plaque. By contrast some stones are composed largely of calcium phosphate, as either hydroxyapatite or brushite (calcium monohydrogen phosphate), and are usually accompanied by deposits of calcium phosphate in the Bellini ducts. These deposits result in local tissue damage and might serve as a site of mineral overgrowth. Stone formation is driven by supersaturation of urine with calcium oxalate and brushite. The level of supersaturation is related to fluid intake as well as to the levels of urinary citrate and calcium. Risk of stone formation is increased when urine citrate excretion is <400 mg per day, and treatment with potassium citrate has been used to prevent stones. Urine calcium levels >200 mg per day also increase stone risk and often result in negative calcium balance. Reduced renal calcium reabsorption has a role in idiopathic hypercalciuria. Low sodium diets and thiazide-type diuretics lower urine calcium levels and potentially reduce the risk of stone recurrence and bone diseas PMID:27452364

The effect of carbon dioxide on the twinkling artifact in ultrasound imaging of kidney stones: A pilot study

PubMed Central

Simon, Julianna C.; Wang, Yak-Nam; Cunitz, Bryan W.; Thiel, Jeffrey; Starr, Frank; Liu, Ziyue; Bailey, Michael R.

2016-01-01

Bone demineralization, dehydration, and stasis put astronauts at an increased risk of forming kidney stones in space. The color-Doppler ultrasound “twinkling artifact”, which highlights kidney stones with color, can make stones readily detectable with ultrasound; however our previous results suggest twinkling is caused by microbubbles on the stone surface which could be affected by the elevated levels of carbon dioxide found on space vehicles. Four pigs were implanted with kidney stones and imaged with ultrasound while the anesthetic carrier gas oscillated between oxygen and air containing 0.8% carbon dioxide. Upon exposing pigs to 0.8% carbon dioxide, twinkling was significantly reduced after 9–25 minutes and recovered when the carrier gas returned to oxygen. These trends repeated when pigs were again exposed to 0.8% carbon dioxide followed by oxygen. The reduction of twinkling from exposure to elevated carbon dioxide may make kidney stone detection with twinkling difficult in current space vehicles. PMID:28190622

Method for fabricating laminated uranium composites

DOEpatents

Chapman, L.R.

1983-08-03

The present invention is directed to a process for fabricating laminated composites of uranium or uranium alloys and at least one other metal or alloy. The laminated composites are fabricated by forming a casting of the molten uranium with the other metal or alloy which is selectively positioned in the casting and then hot-rolling the casting into a laminated plate in or around which the casting components are metallurgically bonded to one another to form the composite. The process of the present invention provides strong metallurgical bonds between the laminate components primarily since the bond disrupting surface oxides on the uranium or uranium alloy float to the surface of the casting to effectively remove the oxides from the bonding surfaces of the components.

Contemporary Attitudes and Practice Patterns of North American Urologists in Investigating Stone-Forming Patients-A Survey of Endourological Society Members.

PubMed

McGuire, Barry B; Matulewicz, Richard S; Zuccarino-Crowe, Rian; Nadler, Robert B; Perry, Kent T

2016-04-01

Recent evidence would suggest a low rate of metabolic assessment in stone formers, even in those deemed as high risk. We wished to assess the attitudes and practice patterns of metabolic work up in North American members of the Endourological Society as part of the management of stone-forming patients. A 12-question online multiple-choice questionnaire (using Survey Monkey(®)) was distributed to all members of the Endourological Society through e-mail. Descriptive analyses were performed. A total of 124 North American members of the Endourological Society responded (90% endourologists, 65% fellowship trained). Ninety-seven percent perform metabolic assessments without referring to a consultant. Eighty-three percent use a commercial analysis company and 17% request serum or urine parameters individually. Ninety-seven percent believe that 24-48-hour urine collection is a better way of assessing patients for metabolic abnormalities than a "basic analysis." Many respondents (37%) would be more likely to metabolically assess if results were easier to interpret, and 35% would like assistance/advice in the interpretation of results. At initial investigation of a first-time stone former, 87% of respondents use serum chemistry, 48% use 24-hour urine, 26% use 48-hour urine (two consecutive 24-hour urine collections), 54% send stone for analysis, and 7% do not investigate. On recurrent stone formers, 69% use serum chemistry, 73% use 24/48-hour urine, and 23% send stone for analysis. On routine follow-up, 36% check serum chemistry, 55% use 24-hour urine, 2% use 48-hour urine, and 29% do not metabolically evaluate. The majority agree that pharmacologic therapy plays a strong role in preventing recurrence (90%). After initiating pharmacologic therapy, 59% reassess using serum chemistry and 84% and 7% use 24/48-hour urine collection, respectively. Physicians re-evaluate patients after 1 month (7%), 1-2 months (10%), 2-4 months (44%), 4-6 months (30%), or after 6-12 months (7%). This snapshot assessment of Endourological Society members' practices in the metabolic investigation of stone-forming patients demonstrates wide testing variations. Many physicians expressed interest in assistance/advice in the interpretation of the metabolic assessment results.

Spall behavior of cast iron with varying microstructures

NASA Astrophysics Data System (ADS)

Plume, Gifford; Rousseau, Carl-Ernst

2014-07-01

The spall strength of cast iron with varying microstructures has been investigated using plate impact at moderate speed. Stress history measurements were made with manganin stress gauges embedded between the back face of the specimen and a low impedance polycarbonate backing. Five separate cast irons were tested. Four of these consisted of gray cast iron with graphite in flake form, with three classified as Type VII A2 and the fourth containing a bimodal distribution of Types VII A4 and VII D8. The fifth casting consisted of ductile cast iron with graphite in nodular form, classified as Type I, size class 5. The spall strength for the Type VII A2 gray cast irons varied between 40 and 370 MPa, and that of the additional gray cast iron, between 410 and 490 MPa. The spall strength of the ductile cast iron fell within the range of 0.94-1.2 GPa. It is shown that the spall strength is linked to the damage level at the spall plane, where an increased level of tensile stress is required to generate higher levels of damage. Post mortem analysis was performed on the recovered samples, revealing the graphite phase to be the primary factor governing the spall fracture of cast irons, where crack nucleation is directly correlated to the debonding of graphite from the metal matrix. The average length of graphite found within a casting is linked to the material's strength, where strength increases as a function of decreasing length. The morphology and mean free path of graphite precipitates further govern the subsequent coalescence of initiated cracks to form a complete fracture plane. In cases where graphite spacing is large, increased energy level is required to complete the fracture process. A secondary factor governing the spall fracture of cast irons has also been linked to the microstructure of the metal matrix, with pearlite yielding higher spall strengths than free ferrite.

Corrosion casts of big bubbles formed during deep anterior lamellar keratoplasty.

PubMed

Feizi, Sepehr; Kanavi, Mozhgan Rezaei; Kharaghani, Davood; Balagholi, Sahar; Meskinfam, Masoumeh; Javadi, Mohammad Ali

2016-11-01

To characterize the walls of big bubbles formed during deep anterior lamellar keratoplasty (DALK) using the corrosion casting technique. Fresh corneoscleral buttons with normal transparency and without any known eye diseases (n = 11) were obtained from 11 human donors. A 20-gauge needle was used to inject a solution of 20 % polyvinyl alcohol (PVA) immediately beneath the corneal endothelium to form big bubbles in eight corneoscleral buttons. In the second experiment on three corneoscleral buttons, a big bubble was first formed by air injection beneath the endothelium. Thereafter, 20 % PVA was injected into the bubble space. Scanning electron microscopy was used to characterize the surfaces of the casts, which replicated the walls of the big bubbles. A type-1 bubble was formed in all corneas. In one cornea, one type-1 bubble was initially formed centrally, and while it was enlarged, an eccentric type-2 bubble appeared. Scanning electron microscopy showed that the casts of type-1 bubbles had two distinct surfaces. The anterior surface demonstrated several holes or pits, depending on the material used for the bubble formation, whereas the posterior surface exhibited an uneven surface. The anterior and posterior surfaces of the type-2 cast were more or less similar. A communication measuring 531.9 µm in length and 171.4 µm in diameter was found between the two bubbles. The corrosion casting technique provides a permanent three-dimensional record of the potential spaces and barriers in the posterior corneal stroma, which explains several features associated with big-bubble DALK.

Evaluation of Musa (Paradisiaca Linn. cultivar)--"Puttubale" stem juice for antilithiatic activity in albino rats.

PubMed

Prasad, K V; Bharathi, K; Srinivasan, K K

1993-10-01

The fresh juice of Musa stem (Puttubale) was tested for its antilithiatic activity. Zinc discs were implanted in the urinary bladder of albino rats to induce urolithiasis. The stones formed were mainly of magnesium ammonium phosphate with traces of calcium oxalate. Musa stem juice (3 mL/rat/day orally) was found to be effective in reducing the formation and also in dissolving the pre-formed stones.

Clinical, demographic, and laboratory characteristics of children with nephrolithiasis.

PubMed

Sas, David J; Becton, Lauren J; Tutman, Jeffrey; Lindsay, Laura A; Wahlquist, Amy H

2016-06-01

While the incidence of pediatric kidney stones appears to be increasing, little is known about the demographic, clinical, laboratory, imaging, and management variables in this patient population. We sought to describe various characteristics of our stone-forming pediatric population. To that end, we retrospectively reviewed the charts of pediatric patients with nephrolithiasis confirmed by imaging. Data were collected on multiple variables from each patient and analyzed for trends. For body mass index (BMI) controls, data from the general pediatrics population similar to our nephrolithiasis population were used. Data on 155 pediatric nephrolithiasis patients were analyzed. Of the 54 calculi available for analysis, 98 % were calcium based. Low urine volume, elevated supersaturation of calcium phosphate, elevated supersaturation of calcium oxalate, and hypercalciuria were the most commonly identified abnormalities on analysis of 24-h urine collections. Our stone-forming population did not have a higher BMI than our general pediatrics population, making it unlikely that obesity is a risk factor for nephrolithiasis in children. More girls presented with their first stone during adolescence, suggesting a role for reproductive hormones contributing to stone risk, while boys tended to present more commonly at a younger age, though this did not reach statistical significance. These intriguing findings warrant further investigation.

An update and practical guide to renal stone management.

PubMed

Johri, Nikhil; Cooper, Bruce; Robertson, William; Choong, Simon; Rickards, David; Unwin, Robert

2010-01-01

Renal stone disease covers kidney and lower urinary tract stones caused by a variety of conditions, including metabolic and inherited disorders, and anatomical defects with or without chronic urinary infection. Most cases are idiopathic, in which there is undoubtedly a genetic predisposition, but where environmental and lifestyle factors play an important role. Indeed, it is becoming apparent that renal stone disease is often part of a larger 'metabolic picture' commonly associated with type 2 diabetes, obesity, dyslipidaemia, and hypertension. Renal stone disease is a growing problem in the UK (and other developed and developing populations) with a cross-sectional prevalence of ∼1.2%. This means that there are currently ∼720,000 individuals with a history of kidney stones in the UK. Almost 40% of first-time stone formers will form a second stone within 3 years of the first episode if no prophylactic measures are instituted to prevent stone recurrence, since removal or disintegration of the first stone does not treat the underlying cause of stones in the majority of patients. The age of onset is getting younger and the sex ratio (until recently more men than women) is becoming almost even. Metabolic screening remains an important part of investigating renal stone disease, but to the disappointment and frustration of many doctors, medical treatment is still essentially pragmatic, except perhaps in cystinuria, and to a limited extent in primary hyperoxaluria (if pyridoxine-sensitive); although newer treatments may be emerging. This review summarizes current thinking and provides a practical basis for the management of renal stone disease. Copyright © 2010 S. Karger AG, Basel.

Selenium in Paleozoic stone coal (carbonaceous shale) as a significant source of environmental contamination in rural southern China

NASA Astrophysics Data System (ADS)

Belkin, H. E.; Luo, K.

2012-04-01

Selenium occurs in high concentrations (typically > 10 and up to 700 ppm) in organic-rich Paleozoic shales and cherts (called "stone coal" - shíméi), in southern China. Stone coals are black shales that formed in anoxic to euxinic environments and typically contain high concentrations of organic carbon, are enriched in various metals such as V, Mo, Pb, As, Cr, Ni, Se, etc., and are distinguished from "humic" coal in the Chinese literature. We have examined stone coal from Shaanxi, Hubei, and Guizhou Provinces, People's Republic of China and have focused our study on the mode of occurrence of Se and other elements (e.g. As, Pb, etc.) hazardous to human health. Scanning electron microscope, energy-dispersive analysis and electron microprobe wave-length dispersive spectroscopy were used to identify and determine the composition of host phases observed in the stone coals. Native selenium, Se-bearing pyrite and other sulfides are the hosts for Se, although we cannot preclude an organic or clay-mineral association. Stone coals are an important source of fuel (reserves over 1 billion tonnes), both domestically and in small industry, in some rural parts of southern China and present significant environmental problems for the indigenous population. The stone coals create three main environmental problems related to Se pollution. First, the residual soils formed on stone coal are enriched in Se and other metals contained in the stone coals and, depending on the speciation and bioavailability of the metals, may enrich crops and vegetation grown on them. Second, weathering and leaching of the stone coal contaminates the local ground water and/or surface waters with Se and other metals. Third, the local population uses the stone coal as a source of fuel, which releases the more volatile elements (Se and As) into the atmosphere in the homes. The ash will be extremely enriched with the balance of the heavy metal suite. Disposal of the ash on agricultural lands or near water supplies will contaminate both. Human and animal selenosis has been observed in economically and geographically isolated rural communities in areas underlain by stone coal. However, local Public Health officials have adequately dealt with these cases of local selenium poisoning. In Enshi, Hubei Province, Se-contaminated farmland has been replanted with tea and the Se-enriched tea has been marketed nationally.

Methods for manufacturing geometric multi-crystalline cast materials

DOEpatents

Stoddard, Nathan G

2013-11-26

Methods are provided for casting one or more of a semi-conductor, an oxide, and an intermetallic material. With such methods, a cast body of a geometrically ordered multi-crystalline form of the one or more of a semiconductor, an oxide, and an intermetallic material may be formed that is free or substantially free of radially-distributed impurities and defects and having at least two dimensions that are each at least about 10 cm.

Methods for manufacturing monocrystalline or near-monocrystalline cast materials

DOEpatents

Stoddard, Nathan G

2014-04-29

Methods are provided for casting one or more of a semiconductor, an oxide, and an intermetallic material. With such methods, a cast body of a monocrystalline form of the one or more of a semiconductor, an oxide, and an intermetallic material may be formed that is free of, or substantially free of, radially-distributed impurities and defects and having at least two dimensions that are each at least about 35 cm.

Method of casting articles of a bulk-solidifying amorphous alloy

DOEpatents

Lin, X.; Johnson, W.L.; Peker, A.

1998-08-25

A casting charge of a bulk-solidifying amorphous alloy is cast into a mold from a temperature greater than its crystallized melting temperature, and permitted to solidify to form an article. The oxygen content of the casting charge is limited to an operable level, as excessively high oxygen contents produce premature crystallization during the casting operation. During melting, the casting charge is preferably heated to a temperature above a threshold temperature to eliminate heterogeneous crystallization nucleation sites within the casting charge. The casting charge may be cast from above the threshold temperature, or it may be cooled to the casting temperature of more than the crystallized melting point but not more than the threshold temperature, optionally held at this temperature for a period of time, and thereafter cast. 8 figs.

Method of casting articles of a bulk-solidifying amorphous alloy

DOEpatents

Lin, Xianghong; Johnson, William L.; Peker, Atakan

1998-01-01

A casting charge of a bulk-solidifying amorphous alloy is cast into a mold from a temperature greater than its crystallized melting temperature, and permitted to solidify to form an article. The oxygen content of the casting charge is limited to an operable level, as excessively high oxygen contents produce premature crystallization during the casting operation. During melting, the casting charge is preferably heated to a temperature above a threshold temperature to eliminate heterogeneous crystallization nucleation sites within the casting charge. The casting charge may be cast from above the threshold temperature, or it may be cooled to the casting temperature of more than the crystallized melting point but not more than the threshold temperature, optionally held at this temperature for a period of time, and thereafter cast.

Radionuclide Retention Mechanisms in Secondary Waste-Form Testing: Phase II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Um, Wooyong; Valenta, Michelle M.; Chung, Chul-Woo

2011-09-26

This report describes the results from laboratory tests performed at Pacific Northwest National Laboratory (PNNL) for Washington River Protection Solutions (WRPS) to evaluate candidate stabilization technologies that have the potential to successfully treat liquid secondary waste stream effluents produced by the Hanford Tank Waste Treatment and Immobilization Plant (WTP). WRPS is considering the design and construction of a Solidification Treatment Unit (STU) for the Effluent Treatment Facility (ETF) at Hanford. The ETF, a multi-waste, treatment-and-storage unit that has been permitted under the Resource Conservation and Recovery Act (RCRA), can accept dangerous, low-level, and mixed wastewaters for treatment. The STU needsmore » to be operational by 2018 to receive secondary liquid waste generated during operation of the WTP. The STU will provide the additional capacity needed for ETF to process the increased volume of secondary waste expected to be produced by WTP. This report on radionuclide retention mechanisms describes the testing and characterization results that improve understanding of radionuclide retention mechanisms, especially for pertechnetate, {sup 99}TcO{sub 4}{sup -} in four different waste forms: Cast Stone, DuraLith alkali aluminosilicate geopolymer, encapsulated fluidized bed steam reforming (FBSR) product, and Ceramicrete phosphate bonded ceramic. These data and results will be used to fill existing data gaps on the candidate technologies to support a decision-making process that will identify a subset of the candidate waste forms that are most promising and should undergo further performance testing.« less

Extensive characterizations of bacteria isolated from catheterized urine and stone matrices in patients with nephrolithiasis.

PubMed

Tavichakorntrakool, Ratree; Prasongwattana, Vitoon; Sungkeeree, Seksit; Saisud, Phitsamai; Sribenjalux, Pipat; Pimratana, Chaowat; Bovornpadungkitti, Sombat; Sriboonlue, Pote; Thongboonkerd, Visith

2012-11-01

Urinary tract infections are generally known to be associated with nephrolithiasis, particularly struvite stone, in which the most common microbe found is urea-splitting bacterium, i.e. Proteus mirabilis. However, our observation indicated that it might not be the case of stone formers in Thailand. We therefore extensively characterized microorganisms associated with all types of kidney stones. A total of 100 kidney stone formers (59 males and 41 females) admitted for elective percutaneous nephrolithotomy were recruited and microorganisms isolated from catheterized urine and cortex and nidus of their stones were analyzed. From 100 stone formers recruited, 36 cases had a total of 45 bacterial isolates cultivated from their catheterized urine and/or stone matrices. Among these 36 cases, chemical analysis by Fourier-transformed infrared spectroscopy revealed that 8 had the previously classified 'infection-induced stones', whereas the other 28 cases had the previously classified 'metabolic stones'. Calcium oxalate (in either pure or mixed form) was the most common and found in 64 and 75% of the stone formers with and without bacterial isolates, respectively. Escherichia coli was the most common bacterium (approximately one-third of all bacterial isolates) found in urine and stone matrices (both nidus and periphery). Linear regression analysis showed significant correlation (r = 0.860, P < 0.001) between bacterial types in urine and stone matrices. Multidrug resistance was frequently found in these isolated bacteria. Moreover, urea test revealed that only 31% were urea-splitting bacteria, whereas the majority (69%) had negative urea test. Our data indicate that microorganisms are associated with almost all chemical types of kidney stones and urea-splitting bacteria are not the major causative microorganisms found in urine and stone matrices of the stone formers in Thailand. These data may lead to rethinking and a new roadmap for future research regarding the role of microorganisms in kidney stone formation.

From Catheter to Kidney Stone: The Uropathogenic Lifestyle of Proteus mirabilis

PubMed Central

Norsworthy, Allison N.; Pearson, Melanie M.

2017-01-01

Proteus mirabilis is a model organism for urease-producing uropathogens. These diverse bacteria cause infection stones in the urinary tract and form crystalline biofilms on indwelling urinary catheters, frequently leading to poly-microbial infection. Recent work has elucidated how P. mirabilis causes all of these disease states. Particularly exciting is the discovery that this bacterium forms large clusters in the bladder lumen that are sites for stone formation. These clusters, and other steps of infection, require two virulence factors in particular: urease and MR/P fimbriae. Highlighting the importance of MR/P fimbriae is the cotranscribed regulator, MrpJ, which globally controls virulence. Overall, P. mirabilis exhibits an extraordinary lifestyle, and further probing will answer exciting basic microbiological and clinically relevant questions. PMID:28017513

Do Urinary Cystine Parameters Predict Clinical Stone Activity?

PubMed

Friedlander, Justin I; Antonelli, Jodi A; Canvasser, Noah E; Morgan, Monica S C; Mollengarden, Daniel; Best, Sara; Pearle, Margaret S

2018-02-01

An accurate urinary predictor of stone recurrence would be clinically advantageous for patients with cystinuria. A proprietary assay (Litholink, Chicago, Illinois) measures cystine capacity as a potentially more reliable estimate of stone forming propensity. The recommended capacity level to prevent stone formation, which is greater than 150 mg/l, has not been directly correlated with clinical stone activity. We investigated the relationship between urinary cystine parameters and clinical stone activity. We prospectively followed 48 patients with cystinuria using 24-hour urine collections and serial imaging, and recorded stone activity. We compared cystine urinary parameters at times of stone activity with those obtained during periods of stone quiescence. We then performed correlation and ROC analysis to evaluate the performance of cystine parameters to predict stone activity. During a median followup of 70.6 months (range 2.2 to 274.6) 85 stone events occurred which could be linked to a recent urine collection. Cystine capacity was significantly greater for quiescent urine than for stone event urine (mean ± SD 48 ± 107 vs -38 ± 163 mg/l, p <0.001). Cystine capacity significantly correlated inversely with stone activity (r = -0.29, p <0.001). Capacity also correlated highly negatively with supersaturation (r = -0.88, p <0.001) and concentration (r = -0.87, p <0.001). Using the suggested cutoff of greater than 150 mg/l had only 8.0% sensitivity to predict stone quiescence. Decreasing the cutoff to 90 mg/l or greater improved sensitivity to 25.2% while maintaining specificity at 90.9%. Our results suggest that the target for capacity should be lower than previously advised. Copyright © 2018 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

The influence of bacteria on struvite crystal habit and its importance in urinary stone formation

NASA Astrophysics Data System (ADS)

Clapham, L.; McLean, R. J. C.; Nickel, J. C.; Downey, J.; Costerton, J. W.

1990-07-01

Infection-induced urinary stones form as a result of a urinary tract infection by urease-producing bacteria. These stones are not totally crystalline in nature but rather consist of an agglomeration of bacteria, organic matrix, and crystal of struvite (MgNH 4PO 4· 6H 2O). Crystal formation is related to the ability of the bacteria to effect an increase in the urine pH. Another equally important bacterial role lies in their formation of a 'biofilm' which later becomes the organic matrix constituent of the stone. Results of the present in vitro study indicate that crystals are formed more readily if produced within the bacterial biofilm than in the surrounding urine. It is proposed that supersaturation, due in part to a bacterial-induced pH increase and in part to the metal binding tendency of the biofilm, leads to crystal formation via a gel growth mechanism within the biofilm itself. In time further bacterial cell division, microcolony.

A Proposed Methodology to Assess the Accuracy of 3D Scanners and Casts and Monitor Tooth Wear Progression in Patients.

PubMed

Ahmed, Khaled E; Whitters, John; Ju, Xiangyang; Pierce, S Gareth; MacLeod, Charles N; Murray, Colin A

2016-01-01

The aim of this study was to detail and assess the capability of a novel methodology to 3D-quantify tooth wear progression in a patient over a period of 12 months. A calibrated stainless steel model was used to identify the accuracy of the scanning system by assessing the accuracy and precision of the contact scanner and the dimensional accuracy and stability of casts fabricated from three different types of impression materials. Thereafter, the overall accuracy of the 3D scanning system (scanner and casts) was ascertained. Clinically, polyether impressions were made of the patient's dentition at the initial examination and at the 12-month review, then poured in type IV dental stone to assess the tooth wear. The anterior teeth on the resultant casts were scanned, and images were analyzed using 3D matching software to detect dimensional variations between the patient's impressions. The accuracy of the 3D scanning system was established to be 33 μm. 3D clinical analysis demonstrated localized wear on the incisal and palatal surfaces of the patient's maxillary central incisors. The identified wear extended to a depth of 500 μm with a distribution of 4% to 7% of affected tooth surfaces. The newly developed 3D scanning methodology was found to be capable of assessing and accounting for the various factors affecting tooth wear scanning. Initial clinical evaluation of the methodology demonstrates successful monitoring of tooth wear progression. However, further clinical assessment is needed.

Half-heusler alloys with enhanced figure of merit and methods of making

DOEpatents

Ren, Zhifeng; Yan, Xiao; Joshi, Giri; Chen, Shuo; Chen, Gang; Poudel, Bed; Caylor, James Christopher

2015-06-02

Thermoelectric materials and methods of making thermoelectric materials having a nanometer mean grain size less than 1 micron. The method includes combining and arc melting constituent elements of the thermoelectric material to form a liquid alloy of the thermoelectric material and casting the liquid alloy of the thermoelectric material to form a solid casting of the thermoelectric material. The method also includes ball milling the solid casting of the thermoelectric material into nanometer mean size particles and sintering the nanometer size particles to form the thermoelectric material having nanometer scale mean grain size.

Application of Astronomical Compositions in Small Architectural Forms

NASA Astrophysics Data System (ADS)

Haykazun, Ani

2016-12-01

The small architectural forms are an important part of the Armenian architecture. Their compositions are diverse including quadrihedral structures, cross-stones, monuments, gravestones, memorial stones, etc. From ancient times to the late middle ages, and up to themodern small architectural forms, there are many decorative elements of astronomical character. Among them, one can more often see stars, the sun, the moon, the sky, the planets, the sign of eternity and other symbolic decorative images, which play a major role in the formation of the artistic image of the architectural compositions. The analysis of application of astronomical compositions will help more comprehensively introduce the compositional peculiarities of the small architectural forms.

BIOPSY PROVEN MEDULLARY SPONGE KIDNEY: Clinical findings, histopathology, and role of osteogenesis in stone and plaque formation

PubMed Central

Evan, Andrew P.; Worcester, Elaine M.; Williams, James C.; Sommer, Andre J.; Lingeman, James E.; Phillips, Carrie L.; Coe, Fredric L.

2015-01-01

Medullary sponge kidney (MSK) is associated with recurrent stone formation, but the clinical phenotype is unclear because patients with other disorders may be incorrectly labeled MSK. We studied 12 patients with histologic findings pathognomonic of MSK. All patients had an endoscopically recognizable pattern of papillary malformation, which may be segmental or diffuse. Affected papillae are enlarged and billowy, due to markedly enlarged inner medullary collecting ducts (IMCD), which contain small, mobile ductal stones. Patients had frequent dilation of Bellini ducts, with occasional mineral plugs. Stones may form over white (Randall’s) plaque, but most renal pelvic stones are not attached, and have a similar morphology as ductal stones, which are a mixture of calcium oxalate and apatite. Patients had no abnormalities of urinary acidification or acid excretion; the most frequent metabolic abnormality was idiopathic hypercalciuria. Although both Runx2 and Osterix are expressed in papillae of MSK patients, no mineral deposition was seen at the sites of gene expression, arguing against a role of these genes in this process. Similar studies in idiopathic calcium stone formers showed no expression of these genes at sites of Randall’s plaque. The most likely mechanism for stone formation in MSK appears to be crystallization due to urinary stasis in dilated IMCD with subsequent passage of ductal stones into the renal pelvis where they may serve as nuclei for stone formation. PMID:25615853

Effects of water uptake on melamine renal stone formation in mice.

PubMed

Peng, Jiao; Li, Daxu; Chan, Yee Kwan; Chen, Yan; Lamb, Jonathan R; Tam, Paul K H; El-Nezami, Hani

2012-06-01

Melamine-tainted food can induce kidney stones both in humans and animals and in domestic animals, severe cases caused acute kidney failure and death. Although increasing water intake can ameliorate kidney stone formation, its effect on melamine (Mel)-induced kidney stones has not been studied. We have analysed the effect of restricted ingestion of drinking water on melamine stone formation in mice. They were given melamine and cyanuric acid orally and received drinking water either freely or for a restricted time. Kidney stone formation and renal function were monitored. Mice receiving drinking water for a restricted 10-h period initially lost body weight, which returned to normal within 2 days. No other abnormalities were observed. Ingestion of melamine alone failed to induce kidney stones even under conditions of restricted drinking water. In mice treated with melamine together with cyanuric acid for 3 days, no renal stones were formed when the supply of drinking was normal. However, when drinking water was limited, stone formation was observed and accompanied by high levels of serum urea and creatinine. An increase in urine haemoglobin and glucose levels was also found. The administration resulted in up-regulated tissue osteopontin, kidney injury molecule-1 and neutrophil gelatinase-associated lipocalin messenger RNA expression and macrophage infiltration. Our results indicate the importance of water intake in the formation of melamine-induced renal stone formation in the mouse and provide new information on the mechanisms of melamine stone formation.

Tanjore: Mystical Painting of India

ERIC Educational Resources Information Center

Henn, Cynthia A.

2004-01-01

Tanjore (or Thanjavur or Thanlavoor) paintings are one of the most popular traditional art forms in Southern India. These ornate religious paintings involve Hindu mythology. The paintings are noted for their adornment of gold and semiprecious stones such as rubies, emeralds, and pearls. Currently, the semiprecious stones are often substituted…

Method and apparatus for in-situ drying investigation and optimization of slurry drying methodology

DOEpatents

Armstrong, Beth L.; Daniel, Claus; Howe, Jane Y.; Kiggans, Jr, James O.; Sabau, Adrian S.; Wood, III, David L.; Kalnaus, Sergiy

2016-05-10

A method of drying casted slurries that includes calculating drying conditions from an experimental model for a cast slurry and forming a cast film. An infrared heating probe is positioned on one side of the casted slurry and a thermal probe is positioned on an opposing side of the casted slurry. The infrared heating probe may control the temperature of the casted slurry during drying. The casted slurry may be observed with an optical microscope, while applying the drying conditions from the experimental model. Observing the casted slurry includes detecting the incidence of micro-structural changes in the casted slurry during drying to determine if the drying conditions from the experimental model are optimal.

Method of forming a relatively stable slip of silicon metal particles and yttrium containing particles

DOEpatents

Dickie, Ray A.; Mangels, John A.

1984-01-01

The method concerns forming a relatively stable slip of silicon metal particles and yttrium containing particles. In one embodiment, a casting slip of silicon metal particles is formed in water. Particles of a yttrium containing sintering aid are added to the casting slip. The yttrium containing sintering aid is a compound which has at least some solubility in water to form Y.sup.+3 ions which have a high potential for totally flocculating the silicon metal particles into a semiporous solid. A small amount of a fluoride salt is added to the casting slip which contains the yttrium containing sintering aid. The fluoride salt is one which will produce fluoride anions when dissolved in water. The small amount of the fluoride anions produced are effective to suppress the flocculation of the silicon metal particles by the Y.sup.+3 ions so that all particles remain in suspension in the casting slip and the casting slip has both an increased shelf life and can be used to cast articles having a relatively thick cross-section. The pH of the casting slip is maintained in a range from 7.5 to 9. Preferably, the fluoride salt used is one which is based on a monovalent cation such as sodium or ammonia. The steps of adding the yttrium containing sintering aid and the fluoride salt may be interchanged if desired, and the salt may be added to a solution containing the sintering aid prior to addition of the silicon metal particles.

Effect of Carbon Dioxide on the Twinkling Artifact in Ultrasound Imaging of Kidney Stones: A Pilot Study.

PubMed

Simon, Julianna C; Wang, Yak-Nam; Cunitz, Bryan W; Thiel, Jeffrey; Starr, Frank; Liu, Ziyue; Bailey, Michael R

2017-05-01

Bone demineralization, dehydration and stasis put astronauts at increased risk of forming kidney stones in space. The color-Doppler ultrasound "twinkling artifact," which highlights kidney stones with color, can make stones readily detectable with ultrasound; however, our previous results suggest twinkling is caused by microbubbles on the stone surface which could be affected by the elevated levels of carbon dioxide found on space vehicles. Four pigs were implanted with kidney stones and imaged with ultrasound while the anesthetic carrier gas oscillated between oxygen and air containing 0.8% carbon dioxide. On exposure of the pigs to 0.8% carbon dioxide, twinkling was significantly reduced after 9-25 min and recovered when the carrier gas returned to oxygen. These trends repeated when pigs were again exposed to 0.8% carbon dioxide followed by oxygen. The reduction of twinkling caused by exposure to elevated carbon dioxide may make kidney stone detection with twinkling difficult in current space vehicles. Copyright © 2016 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

Nephrolithiasis in identical twins: the impact of nature vs nurture.

PubMed

Haleblian, George E; Cantor, David A; Sur, Roger L; Assimos, Dean G; Preminger, Glenn M

2007-09-01

To assess possible underlying metabolic abnormalities in three sets of monozygotic twins, to evaluate the interplay among the factors of kidney stone formation, a complex multifactorial process influenced by environmental, genetic and anatomical factors. Three sets of identical twins with either cystine or calcium oxalate stones were identified. Demographic data, medical histories and the results of 24-h urine testing, with samples collected on self-selected diets, were reviewed and analysed. The cystinuric twins had very similar cystine excretion rates, while stone activity was significantly more pronounced in one. Metabolic abnormalities were concordant in one set of twins with calcium oxalate stones, both being hypercalciuric and hyperuricosuric. However, metabolic abnormalities were discordant in the other pair, one twin with hypercalciuria and the other with hypocitraturia. Two of the three pairs had low urinary volume. These results support previous observations that environmental, genetic and potentially, anatomical factors play roles in kidney-stone formation. Additional controlled studies of monozygotic stone-forming twins might help to define the interplay between environmental and genetic factors, and allow the identification of susceptibility genes involved in stone generation.

Stone-isolated carbonatogenic bacteria as inoculants in bioconsolidation treatments for historical limestone.

PubMed

Jroundi, Fadwa; Gómez-Suaga, Patricia; Jimenez-Lopez, Concepción; González-Muñoz, Maria Teresa; Fernandez-Vivas, Maria Antonia

2012-05-15

Stone consolidation treatments that use bacterial biomineralization are mainly based on two strategies: (1) the inoculation of a bacterial culture with proven carbonatogenic ability and/or (2) the application of a culture medium capable of activating those bacteria able to induce the formation of calcium carbonate, from amongst the bacterial community of the stone. While the second strategy has been demonstrated to be effective and, unlike first strategy, it does not introduce any exogenous microorganism into the stone, problems may arise when the bacterial community of the stone is altered, for instance by the use of biocides in the cleaning process. In this study we isolate bacteria that belong to the natural microbial community of the stone and which have proven biomineralization capabilities, with the aim of preparing an inoculum that may be used in stone consolidation treatments wherein the natural community of those stones is altered. With this aim, outdoor experiments were undertaken to activate and isolate bacteria that display high biomineralization capacity from altered calcarenite stone. Most of the bacteria precipitated calcium carbonate in the form of calcite. The selected bacteria were phylogenetically affiliated with members of Actinobacteria, Gamma-proteobacteria and Firmicutes. Furthermore, the capability of these selected carbonatogenic bacteria to consolidate altered calcarenite stone slabs was studied in in vitro experiments, both in the presence and the absence of Myxococcus xanthus, as a potential reinforcement for the bacterial biomineralization. Herein, Acinetobacter species, belonging to the microbial community of the stone, are proposed as powerful carbonatogenic bacteria that, inoculated under appropriate conditions, may be used as inoculum for calcareous stone conservation/consolidation in restoration interventions where the microbial community of the stone is altered. Copyright © 2012 Elsevier B.V. All rights reserved.

Targeted microbubbles: a novel application for the treatment of kidney stones.

PubMed

Ramaswamy, Krishna; Marx, Vanessa; Laser, Daniel; Kenny, Thomas; Chi, Thomas; Bailey, Michael; Sorensen, Mathew D; Grubbs, Robert H; Stoller, Marshall L

2015-07-01

Kidney stone disease is endemic. Extracorporeal shockwave lithotripsy was the first major technological breakthrough where focused shockwaves were used to fragment stones in the kidney or ureter. The shockwaves induced the formation of cavitation bubbles, whose collapse released energy at the stone, and the energy fragmented the kidney stones into pieces small enough to be passed spontaneously. Can the concept of microbubbles be used without the bulky machine? The logical progression was to manufacture these powerful microbubbles ex vivo and inject these bubbles directly into the collecting system. An external source can be used to induce cavitation once the microbubbles are at their target; the key is targeting these microbubbles to specifically bind to kidney stones. Two important observations have been established: (i) bisphosphonates attach to hydroxyapatite crystals with high affinity; and (ii) there is substantial hydroxyapatite in most kidney stones. The microbubbles can be equipped with bisphosphonate tags to specifically target kidney stones. These bubbles will preferentially bind to the stone and not surrounding tissue, reducing collateral damage. Ultrasound or another suitable form of energy is then applied causing the microbubbles to induce cavitation and fragment the stones. This can be used as an adjunct to ureteroscopy or percutaneous lithotripsy to aid in fragmentation. Randall's plaques, which also contain hydroxyapatite crystals, can also be targeted to pre-emptively destroy these stone precursors. Additionally, targeted microbubbles can aid in kidney stone diagnostics by virtue of being used as an adjunct to traditional imaging methods, especially useful in high-risk patient populations. This novel application of targeted microbubble technology not only represents the next frontier in minimally invasive stone surgery, but a platform technology for other areas of medicine. © 2014 The Authors BJU International © 2014 BJU International Published by John Wiley & Sons Ltd.

A collector's passion from catching the stone to sharing the view

USDA-ARS?s Scientific Manuscript database

This is an introduction to a second edition of the catalogue for the groundbreaking 2008 exhibition at the U.S. National Arboretum's National Bonsai & Penjing Museum - Beyond the Black Mountain: Color, Pattern, and Form in American Viewing Stones. The National Bonsai & Penjing Museum is one of the f...

The behaviour of entrainment defects formed in commercial purity Mg alloy cast under a cover gas of SF6

NASA Astrophysics Data System (ADS)

Li, T.; Griffiths, W. D.

2016-03-01

In the casting of light alloys, the oxidised film on the melt surface can be folded due to surface turbulence, thus forming entrainment defects that have a significant negative effect on the mechanical properties of castings. Previous researchers reported that the surface film of Mg alloys formed in an atmosphere containing SF6 had a complicated structure composed of MgO and MgF2. The work reported here aims to investigate the behaviour of entrainment defects formed in magnesium alloys protected by SF6-containing atmospheres. Tensile test bars of commercial purity Mg were cast in an unsealed environment under a cover gas of pure SF6. 34Scanning electron microscopy (SEM) of the fracture surface of the test bars indicated entrainment defects that consisted of symmetrical films containing MgO, but also sulphur and fluorine. The results of these examinations of the symmetrical films were used to infer the potential formation and development of entrainment defects in commercial purity Mg alloy.

Tape-cast sensors and method of making

DOEpatents

Mukundan, Rangachary [Santa Fe, NM; Brosha, Eric L [Los Alamos, NM; Garzon, Fernando H [Santa Fe, NM

2009-08-18

A method of making electrochemical sensors in which an electrolyte material is cast into a tape. Prefabricated electrodes are then partially embedded between two wet layers of the electrolyte tape to form a green sensor, and the green sensor is then heated to sinter the electrolyte tape around the electrodes. The resulting sensors can be used in applications such as, but not limited to, combustion control, environmental monitoring, and explosive detection. A electrochemical sensor formed by the tape-casting method is also disclosed.

From Catheter to Kidney Stone: The Uropathogenic Lifestyle of Proteus mirabilis.

PubMed

Norsworthy, Allison N; Pearson, Melanie M

2017-04-01

Proteus mirabilis is a model organism for urease-producing uropathogens. These diverse bacteria cause infection stones in the urinary tract and form crystalline biofilms on indwelling urinary catheters, frequently leading to polymicrobial infection. Recent work has elucidated how P. mirabilis causes all of these disease states. Particularly exciting is the discovery that this bacterium forms large clusters in the bladder lumen that are sites for stone formation. These clusters, and other steps of infection, require two virulence factors in particular: urease and MR/P fimbriae. Highlighting the importance of MR/P fimbriae is the cotranscribed regulator, MrpJ, which globally controls virulence. Overall, P. mirabilis exhibits an extraordinary lifestyle, and further probing will answer exciting basic microbiological and clinically relevant questions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Hyperoxaluria and Bariatric Surgery

NASA Astrophysics Data System (ADS)

Asplin, John R.

2007-04-01

Bariatric surgery as a means to treat obesity is becoming increasingly common in the United States. An early form of bariatric surgery, the jejunoileal bypass, had to be abandoned in 1980 due to numerous complications, including hyperoxaluria and kidney stones. Current bariatric procedures have not been systematically evaluated to determine if they cause hyperoxaluria. Presented here are data showing that hyperoxaluria is the major metabolic abnormality in patients with bariatric surgery who form kidney stones. Further studies are needed to assess the prevalence of hyperoxaluria in all patients with bariatric surgery.

Grindability of alpha-case formed on cast titanium.

PubMed

Koike, Marie; Jacobson, David; Chan, Kwai S; Okabe, Toru

2009-09-01

The hardened alpha-case (alpha-case) layer inevitably forms on the surface of titanium castings when prepared by investment casting. Because the hardness of the alpha-case is incomparable to that of the interior structure, the perception exists that the alpha-case is difficult to remove during cutting, grinding and polishing. Grindability (ease of grinding) of cast cpTi and cast Ti-6Al-4V was evaluated by grinding cast specimens incrementally using a SiC abrasive wheel. The present study revealed that the presence of the brittle alpha-case with lower fracture toughness is beneficial in grinding titanium. The alpha-case on the ductile cpTi can be ground much easier than its bulk interior structure. In less ductile Ti-6Al-4V, the grinding rate is much higher than that of cpTi, and the alpha-case and its interior structure are at similar levels since the fracture toughness of its alpha-case and the bulk material is not large enough.

Resistance against bacterial leakage of four luting agents used for cementation of complete cast crowns.

PubMed

Zmener, Osvaldo; Pameijer, Cornelis H; Hernández, Sandra

2014-02-01

To assess the sealing properties of four luting materials used for cementation of full cast crowns. 40 human premolars were prepared with a chamfer finish line. Stone dies were fabricated and copings were waxed, invested and cast in gold. Ten samples (n = 10) were randomly assigned to four groups. In two groups, resin modified glass-ionomer cements were used, ACTIVA BioACTIVE-CEMENT/BASE/LINER and FujiCem2; the third group received the self-adhesive resin cement Embrace WetBond, while the fourth group served as control with a zinc phosphate cement. After cementation, excess cement was removed followed by bench-set for 10 minutes. All samples were stored in water at 37 degrees C and subjected to thermal cycling (x2000 between 5 and 55 degrees C). Subsequently the occlusal surface was reduced exposing the dentin. After sterilization the specimens were subjected to bacterial microleakage with E. faecalis in a dual chamber apparatus for a period of 60 days. Bacterial leakage was checked daily. Data were analyzed using the Kaplan-Meyer survival test. Significant pairwise differences were analyzed using the Log Rank test and the Fishers' exact test at P < 0.05. ACTIVA BioACTIVE-CEMENT/BASE/LINER, FujiCem2 and Embrace WetBond showed the lowest microleakage scores and differed statistically significantly (P < 0.05) from zinc phosphate cement.

Effect of various putty-wash impression techniques on marginal fit of cast crowns.

PubMed

Nissan, Joseph; Rosner, Ofir; Bukhari, Mohammed Amin; Ghelfan, Oded; Pilo, Raphael

2013-01-01

Marginal fit is an important clinical factor that affects restoration longevity. The accuracy of three polyvinyl siloxane putty-wash impression techniques was compared by marginal fit assessment using the nondestructive method. A stainless steel master cast containing three abutments with three metal crowns matching the three preparations was used to make 45 impressions: group A = single-step technique (putty and wash impression materials used simultaneously), group B = two-step technique with a 2-mm relief (putty as a preliminary impression to create a 2-mm wash space followed by the wash stage), and group C = two-step technique with a polyethylene spacer (plastic spacer used with the putty impression followed by the wash stage). Accuracy was assessed using a toolmaker microscope to measure and compare the marginal gaps between each crown and finish line on the duplicated stone casts. Each abutment was further measured at the mesial, buccal, and distal aspects. One-way analysis of variance was used for statistical analysis. P values and Scheffe post hoc contrasts were calculated. Significance was determined at .05. One-way analysis of variance showed significant differences among the three impression techniques in all three abutments and at all three locations (P < .001). Group B yielded dies with minimal gaps compared to groups A and C. The two-step impression technique with 2-mm relief was the most accurate regarding the crucial clinical factor of marginal fit.

Methods and apparatuses for manufacturing monocrystalline cast silicon and monocrystalline cast silicon bodies for photovoltaics

DOEpatents

Stoddard, Nathan G [Gettysburg, PA

2011-11-01

Methods and apparatuses are provided for casting silicon for photovoltaic cells and other applications. With such methods and apparatuses, a cast body of monocrystalline silicon may be formed that is free of, or substantially free of, radially-distributed impurities and defects and having at least two dimensions that are each at least about 35 cm is provided.

Cast dielectric composite linear accelerator

DOEpatents

Sanders, David M [Livermore, CA; Sampayan, Stephen [Manteca, CA; Slenes, Kirk [Albuquerque, NM; Stoller, H M [Albuquerque, NM

2009-11-10

A linear accelerator having cast dielectric composite layers integrally formed with conductor electrodes in a solventless fabrication process, with the cast dielectric composite preferably having a nanoparticle filler in an organic polymer such as a thermosetting resin. By incorporating this cast dielectric composite the dielectric constant of critical insulating layers of the transmission lines of the accelerator are increased while simultaneously maintaining high dielectric strengths for the accelerator.

Distinguishing characteristics of idiopathic calcium oxalate kidney stone formers with low amounts of Randall's plaque.

PubMed

Wang, Xiangling; Krambeck, Amy E; Williams, James C; Tang, Xiaojing; Rule, Andrew D; Zhao, Fang; Bergstralh, Eric; Haskic, Zejfa; Edeh, Samuel; Holmes, David R; Herrera Hernandez, Loren P; Lieske, John C

2014-10-07

Overgrowth of calcium oxalate on Randall's plaque is a mechanism of stone formation among idiopathic calcium oxalate stone-formers (ICSFs). It is less clear how stones form when there is little or no plaque. Participants were a consecutive cohort of ICSFs who underwent percutaneous nephroscopic papillary mapping in the kidney or kidneys containing symptomatic stones and a papillary tip biopsy from a representative calyx during a stone removal procedure between 2009 and 2013. The distribution of Randall's plaque coverage was analyzed and used to divide ICSFs into those with a high (≥5%; mean, 10.5%; n=10) versus low (<5%; mean, 1.5%; n=32) amount of plaque coverage per papilla. Demographic and laboratory features were compared between these two groups. Low-plaque stone formers tended to be obese (50% versus 10%; P=0.03) and have a history of urinary tract infection (34% versus 0%; P=0.04). They were less likely to have multiple prior stone events (22% versus 80%; P=0.002) and had a lower mean 24-hour urine calcium excretion (187±86 mg versus 291±99 mg; P<0.01). Morphologically, stones from patients with low amounts of plaque lacked a calcium phosphate core by microcomputed tomography. Papillary biopsies from low plaque stone-formers revealed less interstitial and basement membrane punctate crystallization. These findings suggest that other pathways independent of Randall's plaque may contribute to stone pathogenesis among a subgroup of ICSFs who harbor low amounts of plaque. Copyright © 2014 by the American Society of Nephrology.

Quality Assessment of Urinary Stone Analysis: Results of a Multicenter Study of Laboratories in Europe

PubMed Central

Siener, Roswitha; Buchholz, Noor; Daudon, Michel; Hess, Bernhard; Knoll, Thomas; Osther, Palle J.; Reis-Santos, José; Sarica, Kemal; Traxer, Olivier; Trinchieri, Alberto

2016-01-01

After stone removal, accurate analysis of urinary stone composition is the most crucial laboratory diagnostic procedure for the treatment and recurrence prevention in the stone-forming patient. The most common techniques for routine analysis of stones are infrared spectroscopy, X-ray diffraction and chemical analysis. The aim of the present study was to assess the quality of urinary stone analysis of laboratories in Europe. Nine laboratories from eight European countries participated in six quality control surveys for urinary calculi analyses of the Reference Institute for Bioanalytics, Bonn, Germany, between 2010 and 2014. Each participant received the same blinded test samples for stone analysis. A total of 24 samples, comprising pure substances and mixtures of two or three components, were analysed. The evaluation of the quality of the laboratory in the present study was based on the attainment of 75% of the maximum total points, i.e. 99 points. The methods of stone analysis used were infrared spectroscopy (n = 7), chemical analysis (n = 1) and X-ray diffraction (n = 1). In the present study only 56% of the laboratories, four using infrared spectroscopy and one using X-ray diffraction, fulfilled the quality requirements. According to the current standard, chemical analysis is considered to be insufficient for stone analysis, whereas infrared spectroscopy or X-ray diffraction is mandatory. However, the poor results of infrared spectroscopy highlight the importance of equipment, reference spectra and qualification of the staff for an accurate analysis of stone composition. Regular quality control is essential in carrying out routine stone analysis. PMID:27248840

Quality Assessment of Urinary Stone Analysis: Results of a Multicenter Study of Laboratories in Europe.

PubMed

Siener, Roswitha; Buchholz, Noor; Daudon, Michel; Hess, Bernhard; Knoll, Thomas; Osther, Palle J; Reis-Santos, José; Sarica, Kemal; Traxer, Olivier; Trinchieri, Alberto

2016-01-01

After stone removal, accurate analysis of urinary stone composition is the most crucial laboratory diagnostic procedure for the treatment and recurrence prevention in the stone-forming patient. The most common techniques for routine analysis of stones are infrared spectroscopy, X-ray diffraction and chemical analysis. The aim of the present study was to assess the quality of urinary stone analysis of laboratories in Europe. Nine laboratories from eight European countries participated in six quality control surveys for urinary calculi analyses of the Reference Institute for Bioanalytics, Bonn, Germany, between 2010 and 2014. Each participant received the same blinded test samples for stone analysis. A total of 24 samples, comprising pure substances and mixtures of two or three components, were analysed. The evaluation of the quality of the laboratory in the present study was based on the attainment of 75% of the maximum total points, i.e. 99 points. The methods of stone analysis used were infrared spectroscopy (n = 7), chemical analysis (n = 1) and X-ray diffraction (n = 1). In the present study only 56% of the laboratories, four using infrared spectroscopy and one using X-ray diffraction, fulfilled the quality requirements. According to the current standard, chemical analysis is considered to be insufficient for stone analysis, whereas infrared spectroscopy or X-ray diffraction is mandatory. However, the poor results of infrared spectroscopy highlight the importance of equipment, reference spectra and qualification of the staff for an accurate analysis of stone composition. Regular quality control is essential in carrying out routine stone analysis.

Riser Feeding Evaluation Method for Metal Castings Using Numerical Analysis

NASA Astrophysics Data System (ADS)

Ahmad, Nadiah

One of the design aspects that continues to create a challenge for casting designers is the optimum design of casting feeders (risers). As liquid metal solidifies, the metal shrinks and forms cavities inside the casting. In order to avoid shrinkage cavities, risers are added to the casting shape to supply additional molten metal when shrinkage occurs during solidification. The shrinkage cavities in the casting are compensated by controlling the cooling rate to promote directional solidification. This control can be achieved by designing the casting such that the cooling begins at the sections that are farthest away from the risers and ends at the risers. Therefore, the risers will solidify last and feed the casting with the molten metal. As a result, the shrinkage cavities formed during solidification are in the risers which are later removed from the casting. Since casting designers have to usually go through iterative processes of validating the casting designs which are very costly due to expensive simulation processes or manual trials and errors on actual casting processes, this study investigates more efficient methods that will help casting designers utilize their casting experiences systematically to develop good initial casting designs. The objective is to reduce the casting design method iterations; therefore, reducing the cost involved in that design processes. The aim of this research aims at finding a method that can help casting designers design effective risers used in sand casting process of aluminum-silicon alloys by utilizing the analysis of solidification simulation. The analysis focuses on studying the significance of pressure distribution of the liquid metal at the early stage of casting solidification, when heat transfer and convective fluid flow are taken into account in the solidification simulation. The mathematical model of casting solidification was solved using the finite volume method (FVM). This study focuses to improve our understanding of the feeding behavior in aluminum-silicon alloys and the effective feeding by considering the pressure gradient distribution of the molten metal at casting dendrite coherency point. For this study, we will identify the relationship between feeding efficiency, shrinkage behavior and how the change in riser size affects the pressure gradient in the casting. This understanding will be used to help in the design of effective risers.

Nutrition and renal stone disease in space

NASA Technical Reports Server (NTRS)

Zerwekh, Joseph E.

2002-01-01

There is a growing body of evidence from the National Aeronautics and Space Administration and the Russian space program showing that humans exposed to the microgravity environment of space have a greater risk for developing renal stones. Increased bone resorption and the attendant hypercalciuria and hyperphosphaturia contribute significantly to raising the urinary state of saturation with respect to the calcium salts, namely calcium oxalate and calcium phosphate. In addition, other environmental and dietary factors may adversely affect urine composition and increase stone formation risk during space flight. For example, reductions in urinary volume, pH, and citrate contribute to raising stone formation risk. In addition to raising the risk for calcium stone formation, this metabolic profile is conducive to the formation of uric acid stones. Although observations to date have suggested that there may actually be a reduced food intake during the early phase of flight, crew members on longer-duration flights may increase food intake and be at increased risk for stone formation. Taken together, these findings support the use of nutritional recommendations for crew members that would serve to reduce the stone-forming propensity of the urinary environment. Pharmacologic intervention should be directed at raising urinary volumes, diminishing bone losses, and preventing reductions in urinary pH and citrate. Success in reducing the risk for stone formation in astronauts would also be of potential major benefit to the estimated 20 million Americans with nephrolithiasis.

Stone formation and calcification by nanobacteria in the human body

NASA Astrophysics Data System (ADS)

Ciftcioglu, Neva; Bjorklund, Michael; Kajander, E. Olavi

1998-07-01

The formation of discrete and organized inorganic crystalline structures within macromolecular extracellular matrices is a widespread biological phenomenon generally referred to as biomineralization. Recently, bacteria have been implicated as factors in biogeochemical cycles for formation of many minerals in aqueous sediments. We have found nanobacterial culture systems that allow for reproducible production of apatite calcification in vitro. Depending on the culture conditions, tiny nanocolloid-sized particles covered with apatite, forming various size of aggregates and stones were observed. In this study, we detected the presence of nanobacteria in demineralized trilobit fossil, geode, apatite, and calcite stones by immunofluorescence staining. Amethyst and other quartz stones, and chalk gave negative results. Microorganisms are capable of depositing apatite outside the thermodynamic equilibrium in sea water. We bring now evidence that this occurs in the human body as well. Previously, only struvite kidney stones composed of magnesium ammonium phosphate and small amounts of apatite have been regarded as bacteria related. 90 percent of demineralized human kidney stones now screened, contained nanobacteria. At least three different distribution patterns of nanobacteria were conditions, and human kidney stones that are formed from small apatite units. Prerequisites for the formation of kidney stones are the supersaturation of urine and presence of nidi for crystallization. Nanobacteria are important nidi and their presence might be of special interest in space flights where supersaturation of urine is present due to the loss of bone. Furthermore, we bring evidence that nanobacteria may act as crystallization nidi for the formation of biogenic apatite structures in tissue calcification found in e.g., atherosclerotic plaques, extensive metastatic and tumoral calcification, acute periarthritis, malacoplakia, and malignant diseases. In nanaobacteria-infected fibroblasts, electron microscopy revealed intra- and extra-cellular needle-like crystal deposits, which were stainable with von Kossa stain and resemble calcospherules found in pathological calcification. Thus bacteria-mediated apatite formation takes place in aqueous environments, in humans and in geological sediments.

HOW DO STONES FORM? IS UNIFICATION OF THEORIES ON STONE FORMATION POSSIBLE?

PubMed Central

Bird, Victoria Y.; Khan, Saeed R.

2017-01-01

Summary There are two basic pathways for formation of calcium based kidney stones. Most idiopathic calcium oxalate (CaOx) stones are formed in association with sub-epithelial plaques of calcium phosphate (CaP), known as Randall’s plaques, on renal papillary surfaces. Crystal formation and retention within the terminal collecting ducts, the ducts of Bellini, leading to the formation of Randall’s plugs, is the other pathway. Both pathways require supersaturation leading to crystallization, regulated by various crystallization modulators produced in response to changing urinary conditions. High supersaturation, as a result of a variety of genetic and environmental factors, leads to crystallization in the terminal collecting ducts, eventually plugging their openings into the renal pelvis. Stasis behind the plugs may lead to the formation of attached or unattached stones in the tubular lumen. Deposition of crystals on the plug surface facing the pelvic or tubular urine may result in stone formation on the Randall’s plugs. Kidneys of idiopathic stone formers may be subjected to oxidative stress as a result of increased urinary excretion of calcium/oxalate/phosphate and/or decrease in the production of functional crystallization inhibitors or in relation to co-morbidities such as hypertension, atherosclerosis, or acute kidney injury. We have proposed that production of reactive oxygen species (ROS) causes dedifferentiation of epithelial/endothelial cells into osteoblast type cells and deposition of CaP in the basement membrane of renal tubules or vessels. Growth, aggregation and melding of CaP crystals leads to the formation of plaque which grows by further calcification of interstitial collagen and membranous vesicles. Plaque becomes exposed to pelvic urine once the covering papillary epithelium is breached. Surface layers of CaP are replaced by CaOx through direct transformation or demineralization of CaP and mineralization of CaOx. Alternatively, or in addition, CaOx crystals nucleate directly on the plaque surface. Stone growth may also depend upon supersaturation in the pelvic urine, triggering further nucleation, growth and aggregation. PMID:28221139

Toward a unifying framework for evolutionary processes.

PubMed

Paixão, Tiago; Badkobeh, Golnaz; Barton, Nick; Çörüş, Doğan; Dang, Duc-Cuong; Friedrich, Tobias; Lehre, Per Kristian; Sudholt, Dirk; Sutton, Andrew M; Trubenová, Barbora

2015-10-21

The theory of population genetics and evolutionary computation have been evolving separately for nearly 30 years. Many results have been independently obtained in both fields and many others are unique to its respective field. We aim to bridge this gap by developing a unifying framework for evolutionary processes that allows both evolutionary algorithms and population genetics models to be cast in the same formal framework. The framework we present here decomposes the evolutionary process into its several components in order to facilitate the identification of similarities between different models. In particular, we propose a classification of evolutionary operators based on the defining properties of the different components. We cast several commonly used operators from both fields into this common framework. Using this, we map different evolutionary and genetic algorithms to different evolutionary regimes and identify candidates with the most potential for the translation of results between the fields. This provides a unified description of evolutionary processes and represents a stepping stone towards new tools and results to both fields. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Photocatalytic self-cleaning TiO2 coatings on carbonatic stones

NASA Astrophysics Data System (ADS)

Bergamonti, Laura; Bondioli, Federica; Alfieri, Ilaria; Lorenzi, Andrea; Mattarozzi, Monica; Predieri, Giovanni; Lottici, Pier Paolo

2016-02-01

A self-cleaning coating based on TiO2 nanoparticles obtained by sol-gel method in an alkaline environment has been tested on different types of carbonatic stones: Botticino, Carrara and Pietra Dorata, frequently used in historic buildings. XRD and Raman measurements confirmed the nanocrystalline nature of titania in anatase form, with 5-10 nm crystal size, and evidenced a small amount of brookite. A fast photocatalytic oxidation by TiO2 coatings of the stained stones with methyl orange and methylene blue under UV lamp irradiation has been assessed. The enhancement of surface wettability due to UV-induced TiO2 hydrophilicity has been evidenced by contact angle measurements. ESEM/EDS showed a surface distribution of the coating fairly homogeneous. The coating does not introduce significant colorimetric changes of the stones and does not alter the water capillarity absorption. Thus, the alkaline nanocrystalline TiO2 is promising for self-cleaning coatings on carbonatic stones.

The effects of below-elbow immobilization on driving performance.

PubMed

Jones, Evan M; Barrow, Aaron E; Skordas, Nic J; Green, David P; Cho, Mickey S

2017-02-01

There is limited research to guide physicians and patients in deciding whether it is safe to drive while wearing various forms of upper extremity immobilization. The purpose of this study is to evaluate the effect of below-elbow removable splints and fiberglass casts on automobile driving performance. 20 healthy subjects completed 10 runs through a closed, cone-marked driving course while wearing a randomized sequence of four different types of immobilization on each extremity (short arm thumb spica fiberglass cast, short arm fiberglass cast, short arm thumb spica splint, and short arm wrist splint). The first and last driving runs were without immobilization and served as controls. Performance was measured based on evaluation by a certified driving instructor (pass/fail scoring), cones hit, run time, and subject-perceived driving difficulty (1-10 analogue scoring). The greatest number of instructor-scored failures occurred while immobilized in right arm spica casts (n=6; p=0.02) and left arm spica casts (n=5; p=0.049). The right arm spica cast had the highest subject-perceived difficulty (5.2±1.9; p<0.001). All forms of immobilization had significantly increased perceived difficulty compared to control, except for the left short arm splint (2.5±1.6; p>0.05). There was no significant difference in number of cones hit or driving time between control runs and runs with any type of immobilization. Drivers should use caution when wearing any of the forms of upper extremity immobilization tested in this study. All forms of immobilization, with exception of the left short arm splint significantly increased perceived driving difficulty. However, only the fiberglass spica casts (both left and right arm), significantly increased drive run failures due to loss of vehicle control. We recommend against driving when wearing a below-elbow fiberglass spica cast on either extremity. Copyright © 2016. Published by Elsevier Ltd.

Compound cast product and method for producing a compound cast product

DOEpatents

Meyer, Thomas N.; Viswanathan, Srinath

2002-09-17

A compound cast product is formed in a casting mold (14) having a mold cavity (16) sized and shaped to form the cast product. A plurality of injectors (24) is supported from a bottom side (26) of the casting mold (14). The injectors (24) are in fluid communication with the mold cavity (16) through the bottom side (26) of the casting mold (14). A molten material holder furnace (12) is located beneath the casting mold (14). The holder furnace (12) defines molten material receiving chambers (36) configured to separately contain supplies of two different molten materials (37, 38). The holder furnace (12) is positioned such that the injectors (24) extend downward into the receiving chamber (36). The receiving chamber (36) is separated into at least two different flow circuits (51, 52). A first molten material (37) is received in a first flow circuit (51), and a second molten material (38) is received into a second flow circuit (52). The first and second molten materials (37, 38) are injected into the mold cavity (16) by the injectors (24) acting against the force of gravity. The injectors (24) are positioned such that the first and second molten materials (37, 38) are injected into different areas of the mold cavity (16). The molten materials (37, 38) are allowed to solidify and the resulting compound cast product is removed from the mold cavity (16).

Methods and apparatuses for manufacturing geometric multicrystalline cast silicon and geometric multicrystalline cast silicon bodies for photovoltaics

DOEpatents

Stoddard, Nathan G

2015-02-10

Methods and apparatuses are provided for casting silicon for photovoltaic cells and other applications. With such methods and apparatuses, a cast body of geometrically ordered multi-crystalline silicon may be formed that is free or substantially free of radially-distributed impurities and defects and having at least two dimensions that are each at least about 10 cm is provided.

A comparative study between xerographic, computer-assisted overlay generation and animated-superimposition methods in bite mark analyses.

PubMed

Tai, Meng Wei; Chong, Zhen Feng; Asif, Muhammad Khan; Rahmat, Rabiah A; Nambiar, Phrabhakaran

2016-09-01

This study was to compare the suitability and precision of xerographic and computer-assisted methods for bite mark investigations. Eleven subjects were asked to bite on their forearm and the bite marks were photographically recorded. Alginate impressions of the subjects' dentition were taken and their casts were made using dental stone. The overlays generated by xerographic method were obtained by photocopying the subjects' casts and the incisal edge outlines were then transferred on a transparent sheet. The bite mark images were imported into Adobe Photoshop® software and printed to life-size. The bite mark analyses using xerographically generated overlays were done by comparing an overlay to the corresponding printed bite mark images manually. In computer-assisted method, the subjects' casts were scanned into Adobe Photoshop®. The bite mark analyses using computer-assisted overlay generation were done by matching an overlay and the corresponding bite mark images digitally using Adobe Photoshop®. Another comparison method was superimposing the cast images with corresponding bite mark images employing the Adobe Photoshop® CS6 and GIF-Animator©. A score with a range of 0-3 was given during analysis to each precision-determining criterion and the score was increased with better matching. The Kruskal Wallis H test showed significant difference between the three sets of data (H=18.761, p<0.05). In conclusion, bite mark analysis using the computer-assisted animated-superimposition method was the most accurate, followed by the computer-assisted overlay generation and lastly the xerographic method. The superior precision contributed by digital method is discernible despite the human skin being a poor recording medium of bite marks. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Comparison of Dimensional Accuracy between Open-Tray and Closed-Tray Implant Impression Technique in 15° Angled Implants

PubMed Central

Balouch, F; Jalalian, E; Nikkheslat, M; Ghavamian, R; Toopchi, Sh; Jallalian, F; Jalalian, S

2013-01-01

Statement of Problem: Various impression techniques have different effects on the accuracy of final cast dimensions. Meanwhile; there are some controversies about the best technique. Purpose: This study was performed to compare two kinds of implant impression methods (open tray and closed tray) on 15 degree angled implants. Materials and Method: In this experimental study, a steel model with 8 cm in diameter and 3 cm in height were produced with 3 holes devised inside to stabilize 3 implants. The central implant was straight and the other two implants were 15° angled. The two angled implants had 5 cm distance from each other and 3.5 cm from the central implant. Dental stone, high strength (type IV) was used for the main casts. Impression trays were filled with poly ether, and then the two impression techniques (open tray and closed tray) were compared. To evaluate positions of the implants, each cast was analyzed by CMM device in 3 dimensions (x,y,z). Differences in the measurements obtained from final casts and laboratory model were analyzed using t-Test. Results: The obtained results indicated that closed tray impression technique was significantly different in dimensional accuracy when compared with open tray method. Dimensional changes were 129 ± 37μ and 143.5 ± 43.67μ in closed tray and open tray, while coefficient of variation in closed- tray and open tray were reported to be 27.2% and 30.4%, respectively. Conclusion: Closed impression technique had less dimensional changes in comparison with open tray method, so this study suggests that closed tray impression technique is more accurate. PMID:24724130

Fit of cast commercially pure titanium and Ti-6Al-4V alloy crowns before and after marginal refinement by electrical discharge machining.

PubMed

Contreras, Edwin Fernando Ruiz; Henriques, Guilherme Elias Pessanha; Giolo, Suely Ruiz; Nobilo, Mauro Antonio Arruda

2002-11-01

Titanium has been suggested as a replacement for alloys currently used in single-tooth restorations and fixed partial dentures. However, difficulties in casting have resulted in incomplete margins and discrepancies in marginal fit. This study evaluated and compared the marginal fit of crowns fabricated from a commercially pure titanium (CP Ti) and from Ti-6Al-4V alloy with crowns fabricated from a Pd-Ag alloy that served as a control. Evaluations were performed before and after marginal refinement by electrical discharge machining (EDM). Forty-five bovine teeth were prepared to receive complete cast crowns. Stone and copper-plated dies were obtained from impressions. Fifteen crowns were cast with each alloy (CP Ti, Ti-6Al-4V, and Pd-Ag). Marginal fit measurements (in micrometers) were recorded at 4 reference points on each casting with a traveling microscope. Marginal refinement with EDM was conducted on the titanium-based crowns, and measurements were repeated. Data were analyzed with the Kruskal-Wallis test, paired t test, and independent t test at a 1% probability level. The Kruskal-Wallis test showed significant differences among mean values of marginal fit for the as-cast CP Ti crowns (mean [SD], 83.9 [26.1] microm) and the other groups: Ti-6Al-4V (50.8 [17.2] microm) and Pd-Ag (45.2 [10.4] microm). After EDM marginal refinement, significant differences were detected among the Ti-6Al-4V crowns (24.5 [10.9] microm) and the other 2 groups: CP Ti (50.6 [20.0] microm) and Pd-Ag (not modified by EDM). Paired t test results indicated that marginal refinement with EDM effectively improved the fit of CP Ti crowns (from 83.9 to 50.6 microm) and Ti-6Al-4V crowns (from 50.8 to 24.5 microm). However, the difference in improvement between the two groups was not significant by t test. Within the limitations of this study, despite the superior results for Ti-6Al-4V, both groups of titanium-based crowns had clinically acceptable marginal fits. After EDM marginal refinement, the fit of cast CP Ti and Ti-6Al-4V crowns improved significantly.

Human stones.

PubMed

Lonsdale, K

1968-03-15

X-ray diffraction studies have shown that there are several different kinds of human urinary calculi, with different age, sex, period, and geographical distributions. Juvenile bladder stones are typically urate and oxalate in small boys in certain stone belts. They have disappeared in some areas, particularly in Britain, but are still common in Thailand. India. and Turkey. Their cause is unknown. Adult bladder stones, formerly common in elderly men, were largely of uric acid and were due to a faulty diet. Juvenile kidney stones are rare, except in Turkey where they are similar to juvenile bladder stones. Adult kidney stones are by far the most universally common, especially in technically developed communities. They are found in both sexes (equally at postmortem), and in the United States and in Czechoslovakia the average number of hospital entries for stones, relative to the whole population, is about 1 per 1000 per annum (increasing) although the incidence in different districts varies by 4 to 1 or more. Such stones are mainly calcium oxalates and calcium and MgNH(4) phosphates. The incidence among the administrative class is at least 20 times that among agricultural workers, relative to their numbers. Stones are reported also to be an occupational hazard for air pilots. It is probably that much more exercise and the drinking of more water to prevent kidney dehydration (spirits and coffee are not effective for this purpose) would lower the high rate of incidence. Moderate acidification would prevent phosphate supersaturation of the urine, but is not effective for oxalates. It seems certain that, once a suitable seed is formed, epitaxy is largely responsible for deposition from urines that would otherwise remain supersaturated until voided. This would explain the curioLls radial and layered texture of many stones. Laboratory experiments might suggest ways of preventing orientated overgrowth.

Natural stones of historic and future importance in Sweden

NASA Astrophysics Data System (ADS)

Schouenborg, Björn; Andersson, Jenny; Göransson, Mattias

2013-04-01

Several activities and responsibilities of the Geological Survey of Sweden (SGU) are related to the work of the newly formed international Heritage Stone Task Group (HSTG) for designating historically important stones. SGU is among other things a referral organization, frequently dealing with the preparation of statements in connection with the quarrying permit applications of stone producers. When preparing these statements, SGU takes into account a number of parameters, e.g. the importance for local and regional business development, historic importance, area of occurrence, quality of the geological documentation of the stone type, peculiarities of the stone types and technical properties relevant for the intended use. Traditionally, SGU has not worked with bedrock mapping looking at the potential of natural stones production but more commonly looking at the potential production of aggregates, industrial minerals and metals. The competence is, therefore, presently being built up with new databases over important natural stone types and definition of criteria for their selection etc. In this respect the criteria defined by the HSTG provide important help. This work goes hand in hand with the task of proposing stone-deposits and quarries of "national interest". The criteria for selection of a stone type, quarry etc as one of national interest are currently being revised. SGU plays an important role in this work. However, the final decision and appointment lies in the hands of the Swedish Board of Housing, Building and Planning (Boverket), an authority dealing with sustainable land use and regional development, town and country planning. Boverket supervises how the planning legislation is handled by the municipal authorities and the county administrative boards. The two latter organizations are those in charge of giving extraction permits for stone quarrying. The "Hallandia gneiss", of SW Sweden, is described as a case story and presented in this paper. Keywords: Hallandia gneiss, natural stones, historic stones, urban planning and building

Nivelstein sandstone, weakly lithified pure silica sands from the Dutch-German border area, intermittently used in architecture for two millennia

NASA Astrophysics Data System (ADS)

Nijland, Timo G.; Wim Dubelaar, C.

2017-04-01

The current paper provides a concise overview of the geological setting of the Nivelstein sandstone in broad sense, its petrographic and physical characteristics, and its use as natural stone. Miocene pure silica sands occur around Heerlen in the southeastern part of the Dutch province of Limburg and Herzogenrath in adjacent Germany, as well as in the Belgian province of Limburg near Opgrimbie. In Dutch Limburg and in Germany are three large active exploitations, quarrying the sands for industrial purposes. On top of the unconsolidated sands in the Herzogenrath quarry, lithified banks of sandstone occur, known as Nivelstein (or more rarely Herzogenrath) sandstone. This sandstone has been used as dimension stone and ornamental stone since Roman times. In the 11th century the quarry was reopened and after a long period of disuse sandstone blocks were again quarried in the second half of the 19th century. The lithification of the Nivelstein sandstone usually is very weak, with grain to grain contacts and some newly formed quartz rims only. The clay content is extremely low and is restricted to tiny booklets of kaolinite. Despite the weak cementation the Nivelstein sandstone has proved to be very time-resistant building stone that forms a major element in the stone cultural heritage of the Dutch- German border area.

Potential therapeutic activity of Phlogacanthus thyrsiformis Hardow (Mabb) flower extract and its biofabricated silver nanoparticles against chemically induced urolithiasis in male Wistar rats.

PubMed

Das, Poppy; Kumar, Kiran; Nambiraj, Arunai; Rajan, Reshma; Awasthi, Rajendra; Dua, Kamal; M, Himaja

2017-10-01

Urolithiasis is a painful disorder in which stones are formed in the kidney, bladder or urethra. There are no proper therapeutic treatments available for kidney stones and people suffering from larger stones have to undergo surgery which has many side effects. A natural remedy with therapeutic effects that can dissipate and remove even the larger stones would eliminate the need of a surgery and the risks associated with it. The flowers of Phlogacanthus thyrsiformis used in culinary recipes in the north eastern India are also widely used as a folklore medicine for the treatment of kidney stones and liver disorders. The aim of this study was to evaluate the prophylactic and therapeutic activity of the aqueous extract of P. thyrsiformis flowers and its biofabricated silver nanoparticles against struvite urinary stones and calcium oxalate kidney stones. A kidney stone inhibition study was carried out on struvite stones grown in gel medium and calcium oxalate stones in rat models using an aqueous extract of P. thyrsiformis flowers and its biofabricated silver nanoparticles. The aqueous extract of P. thyrsiformis flowers and their biofabricated silver nanoparticles, obtained by a green synthetic method, were used to treat struvite urinary stones in vitro and calcium oxalate kidney stones in vivo. Struvite stones were grown in tubes by gel diffusion technique and were treated with varying concentrations of the extract and its nanoparticles. The size of the struvite stones was monitored for 96h using a travelling microscope. Calcium oxalate stones were induced in male Wistar rats by feeding ethylene glycol-ammonium chloride mixture for 14days. Both, prophylactic and therapeutic activities were evaluated by analyzing the urine, serum and histopathological parameters of the rats. The qualitative screening of water extract unveiled the presence of flavonoids as a major constituent. Both, the extract and the nanoparticles effectively reduced the size of struvite stones in vitro and eliminated calcium oxalate stones in Wistar rats in vivo. The potent therapeutic activity of both extract and silver nanoparticles was observed as compared to preventive activity. Anti-urolithiatic potency can be attributed to the presence of flavonoids. Copyright © 2017 Elsevier B.V. All rights reserved.

Biomimetic Randall's plaque as an in vitro model system for studying the role of acidic biopolymers in idiopathic stone formation.

PubMed

Chidambaram, Archana; Rodriguez, Douglas; Khan, Saeed; Gower, Laurie

2015-01-01

Randall's plaque (RP) deposits seem to be consistent among the most common type of kidney stone formers, idiopathic calcium oxalate stone formers. This group forms calcium oxalate renal stones without any systemic symptoms, which contributes to the difficulty of understanding and treating this painful and recurring disease. Thus, the development of an in vitro model system to study idiopathic nephrolithiasis, beginning with RP pathogenesis, can help in identifying how plaques and subsequently stones form. One main theory of RP formation is that calcium phosphate deposits initially form in the basement membrane of the thin loops of Henle, which then fuse and spread into the interstitial tissue, and ultimately make their way across the urothelium, where upon exposure to the urine, the mineralized tissue serves as a nidus for overgrowth with calcium oxalate into a stone. Our group has found that many of the unusual morphologies found in RP and stones, such as concentrically laminated spherulites and mineralized collagenous tissue, can be reproduced in vitro using a polymer-induced liquid precursor (PILP) process, in which acidic polypeptides induce a liquid phase amorphous precursor to the mineral, yielding non-equilibrium crystal morphologies. Given that there are many acidic proteins and polysaccharides present in the renal tissue and urine, we have put forth the hypothesis that the PILP system may be involved in urolithiasis. Therefore, our goal is to develop an in vitro model system of these two stages of composite stone formation to study the role that various acidic macromolecules may play. In our initial experiments presented here, the development of "biomimetic" RP was investigated, which will then serve as a nidus for calcium oxalate overgrowth studies. To mimic the tissue environment, MatriStem(®) (ACell, Inc.), a decellularized porcine urinary bladder matrix was used, because it has both an intact epithelial basement membrane surface and a tunica propria layer, thus providing the two types of matrix constituents found associated with mineral in the early stages of RP formation. We found that when using the PILP process to mineralize this tissue matrix, the two sides led to dramatically different mineral textures, and they bore a striking resemblance to native RP, which was not seen in the tissue mineralized via the classical crystal nucleation and growth process. The interstitium side predominantly consisted of collagen-associated mineral, while the luminal side had much less mineral, which appeared to be tiny spherules embedded within the basement membrane. Although these studies are only preliminary, they support our hypothesis that kidney stones may involve non-classical crystallization pathways induced by the large variety of macromolecular species in the urinary environment. We believe that mineralization of native tissue scaffolds is useful for developing a model system of stone formation, with the ultimate goal of developing strategies to avoid RP and its detrimental consequences in stone formation, or developing therapeutic treatments to prevent or cure the disease. Supported by NIDDK grant RO1DK092311.

Building stones of our Nation's Capital

USGS Publications Warehouse

Withington, Charles F.

1975-01-01

The buildings of our Nation's Capital serve as an unusual geologic display, for the city has been constructed with rocks from quarries throughout the United States and many distant lands. Each building is a unique museum that not only displays the important features of various stones and the geologic environment in which they were formed, but also serves as an historic witness to the city's growth and to the development of its architecture. This booklet describes the source and appearance of the stones used in Washington, D.C.; it includes a map and a walking guide to assist the visitor in examining them.

Bilateral kidney matrix stones: a rare case

PubMed Central

Lahyani, Mounir; Rhannam, Yassine; Slaoui, Amine; Touzani, Alae; Karmouni, Tarik; Elkhader, Khalid; Koutani, Abdellatif; Andaloussi, Ahmed Ibn attya

2016-01-01

Kedney matrix stones are a rare form of calculi. Flank pain and urinary tract infections (UTI) are the most common presentations of matrix calculi. The diagnosis is usually made at surgery, but some preoperative radiographic findings might be suggestive. Open surgery was the method of choice for treatment. However, combination of ureterorenoscopy and percutaneous nephrolithotomy (PCNL) was found to be safe and effective. We report a rare case of renal and ureteral matrix stones that were diagnosed and treated by open surgery. We also describe its clinical, radiological and therapeutic features through a review of the literature. PMID:28292065

Bilateral kidney matrix stones: a rare case.

PubMed

Lahyani, Mounir; Rhannam, Yassine; Slaoui, Amine; Touzani, Alae; Karmouni, Tarik; Elkhader, Khalid; Koutani, Abdellatif; Andaloussi, Ahmed Ibn Attya

2016-01-01

Kedney matrix stones are a rare form of calculi. Flank pain and urinary tract infections (UTI) are the most common presentations of matrix calculi. The diagnosis is usually made at surgery, but some preoperative radiographic findings might be suggestive. Open surgery was the method of choice for treatment. However, combination of ureterorenoscopy and percutaneous nephrolithotomy (PCNL) was found to be safe and effective. We report a rare case of renal and ureteral matrix stones that were diagnosed and treated by open surgery. We also describe its clinical, radiological and therapeutic features through a review of the literature.

Experimental Procedure for Warm Spinning of Cast Aluminum Components.

PubMed

Roy, Matthew J; Maijer, Daan M

2017-02-01

High performance, cast aluminum automotive wheels are increasingly being incrementally formed via flow forming/metal spinning at elevated temperatures to improve material properties. With a wide array of processing parameters which can affect both the shape attained and resulting material properties, this type of processing is notoriously difficult to commission. A simplified, light-duty version of the process has been designed and implemented for full-size automotive wheels. The apparatus is intended to assist in understanding the deformation mechanisms and the material response to this type of processing. An experimental protocol has been developed to prepare for, and subsequently perform forming trials and is described for as-cast A356 wheel blanks. The thermal profile attained, along with instrumentation details are provided. Similitude with full-scale forming operations which impart significantly more deformation at faster rates is discussed.

Experimental Procedure for Warm Spinning of Cast Aluminum Components

PubMed Central

Roy, Matthew J.; Maijer, Daan M.

2017-01-01

High performance, cast aluminum automotive wheels are increasingly being incrementally formed via flow forming/metal spinning at elevated temperatures to improve material properties. With a wide array of processing parameters which can affect both the shape attained and resulting material properties, this type of processing is notoriously difficult to commission. A simplified, light-duty version of the process has been designed and implemented for full-size automotive wheels. The apparatus is intended to assist in understanding the deformation mechanisms and the material response to this type of processing. An experimental protocol has been developed to prepare for, and subsequently perform forming trials and is described for as-cast A356 wheel blanks. The thermal profile attained, along with instrumentation details are provided. Similitude with full-scale forming operations which impart significantly more deformation at faster rates is discussed. PMID:28190063

Complicated bile duct stones

PubMed Central

Roy, Ashwin; Martin, Derrick

2013-01-01

Common bile duct stones (CBDSs) are solid deposits that can either form within the gallbladder or migrate to the common bile duct (CBD), or form de novo in the biliary tree. In the USA around 15% of the population have gallstones and of these, 3% present with symptoms annually. Because of this, there have been major advancements in the management of gallstones and related conditions. Management is based on the patient's risk profile; young and healthy patients are likely to be recommended for surgery and elderly patients with comorbidities are usually recommended for endoscopic procedures. Imaging of gallstones has advanced in the last 30 years with endoscopic retrograde cholangiopancreatography evolving from a diagnostic to a therapeutic procedure in removing CBDSs. We present a complicated case of a patient with a CBDS and periampullary diverticulum and discuss the techniques used to diagnose and remove the stone from the biliary system. PMID:23946532

Effect of carbon content on friction and wear of cast irons

NASA Technical Reports Server (NTRS)

Buckley, D. H.

1977-01-01

Friction and wear experiments were conducted with cast irons and wrought steels containing various amounts of carbon in the alloy structure in contact with 52100 steel. Gray cast irons were found to exhibit lower friction and wear characteristics than white cast irons. Further, gray cast iron wear was more sensitive to carbon content than was white. Wear with gray cast iron was linearly related to load, and friction was found to be sensitive to relative humidity and carbon content. The form, in which the carbon is present in the alloy, is more important, as the carbon content and no strong relationship seems to exist between hardness of these ferrous alloys and wear.

Vacuum casting of thick polymeric films

NASA Technical Reports Server (NTRS)

Cuddihy, E. F.; Moacanin, J.

1979-01-01

Bubble formation and layering, which often plague vacuum-evaporated films, are prevented by properly regulating process parameters. Vacuum casting may be applicable to forming thick films of other polymer/solvent solutions.

Cutting head for ultrasonic lithotripsy

NASA Technical Reports Server (NTRS)

Anguluo, E. D.; Goodfriend, R. (Inventor)

1985-01-01

A cutting head for attachment to the end of the wire probe of an ultrasonic kidney stone disintegration instrument is described. The cutting head has a plurality of circumferentially arranged teeth formed at one end thereof to provide a cup shaped receptacle for kidney stones encountered during the disintegration procedure. An integral reduced diameter collar diminishes stress points in the wire and reduce breakage thereof.

Cutting Head for Ultrasonic Lithotripsy

NASA Technical Reports Server (NTRS)

Angulo, Earl D. (Inventor); Goodfriend, Roger (Inventor)

1989-01-01

A cutting head for attachment to the end of the wire probe of an ultrasonic kidney stone disintegration instrument. The cutting head has a plurality of circumferentially arranged teeth formed at one end thereof to provide a cup-shaped receptacle for kidney stones encountered during the disintegration procedure. An integral reduced diameter collar diminishes stress points in the wire and reduces breakage thereof.

Structuring in Cement Systems with Introduction of Graphene Nano-Additives

NASA Astrophysics Data System (ADS)

Yanturina, R. A.; Trofimov, B. Ya; Ahmedjanov, R. M.

2017-11-01

At present, one of the most promising areas in the field of concrete research is the study of the effect of nano-additives for the production of highly effective concretes. Many authors have already obtained primary results which testify to the very effective role of nanoadditives based on carbon in modifying concrete. In this paper, the influence of a nano-additive of graphene on the phase composition and microstructure of the cement stone was studied. It has been found that, when a nano-additive of graphene is introduced, low-basic calcium hydrosilicates are mainly formed. This leads to an increase in the compressive strength of concrete. The results of the study of the microstructure of cement stone with nano-additive graphene showed that the high compressive strength of concrete modified with nano-additive graphene is explained by the cement stone dense structure. Thus, it was found that the nanoadditive of graphene contributes to the formation of a dense structure of cement stone, composed mainly of low-basic calcium hydrosilicates, and due to this, the physical and mechanical characteristics of concrete and its resistance to frost and other forms of aggression.

A biological stone from a medieval cemetery in Poland.

PubMed

Gładykowska-Rzeczycka, Judyta J; Nowakowski, Dariusz

2014-01-01

A review of the literature shows that origination of biological stones as well as their pathogenesis mostly depend on the environmental factors. As a result, the structural spectrum of such calculi and their chemical composition are highly diversified. It is well known that biological stones are formed mostly in the digestive and urinary tracts. However, it has been demonstrated that this kind of stony structure can be also, though rarely, found in circulatory and reproductive systems, skin, mucosa, and tear ducts. Although in palaeopathology, the list of biological stones is enriched by stony tumours and/or discharges, it is very difficult to uncover the small size deposits in excavation material. In the literature such findings, originating from different countries and centuries, are few. The described stone was found among the bones of an adult individual in the medieval cemetery of Gdańsk (Poland). The SEM, X-ray spectrometer and chemical evaluation revealed that it was a bladder calculus.

A Biological Stone from a Medieval Cemetery in Poland

PubMed Central

Gładykowska-Rzeczycka, Judyta J.; Nowakowski, Dariusz

2014-01-01

A review of the literature shows that origination of biological stones as well as their pathogenesis mostly depend on the environmental factors. As a result, the structural spectrum of such calculi and their chemical composition are highly diversified. It is well known that biological stones are formed mostly in the digestive and urinary tracts. However, it has been demonstrated that this kind of stony structure can be also, though rarely, found in circulatory and reproductive systems, skin, mucosa, and tear ducts. Although in palaeopathology, the list of biological stones is enriched by stony tumours and/or discharges, it is very difficult to uncover the small size deposits in excavation material. In the literature such findings, originating from different countries and centuries, are few. The described stone was found among the bones of an adult individual in the medieval cemetery of Gdańsk (Poland). The SEM, X-ray spectrometer and chemical evaluation revealed that it was a bladder calculus. PMID:25275551

Usefulness of hounsfield unit and density in the assessment and treatment of urinary stones

PubMed Central

Gücük, Adnan; Üyetürk, Uğur

2014-01-01

Computed tomography (CT) is widely used to examine stones in the urinary system. In addition to the size and location of the stone and the overall health of the kidney, CT can also assess the density of the stone in Hounsfield units (HU). The HU, or Hounsfield density, measured by CT, is related to the density of the tissue or stone. A number of studies have assessed the use of HU in urology. HUs have been used to predict the type and opacity of stones during diagnosis, and the efficacy has been assessed using methods including extracorporeal shock wave lithotripsy (ESWL), percutaneous nephrolithotomy (PCNL), ureterorenoscopic ureterolithotripsy (URSL), and medical expulsive treatment (MET). Previous studies have focused on the success rate of HU for predicting the type of stone and of ESWL treatment. Understanding the composition of the stone plays a key role in determining the most appropriate treatment modality. The most recent reports have suggested that the HU value and its variants facilitate prediction of stone composition. However, the inclusion of data regarding urine, such as pH and presence of crystals, increases the predictive accuracy. HUs, which now form part of the clinical guidelines, allow us to predict the success of ESWL; therefore, they should be taken into account when ESWL is considered as a treatment option. However, there are currently insufficient data available regarding the value of HU for assessing the efficacy of PCNL, URSL, and MET. Studies performed to date suggest that these values would make a significant contribution to the diagnosis and treatment of urinary system stones. However, more data are required to assess this further. PMID:25374823

An integrated fiber and stone basket device for use in Thulium fiber laser lithotripsy

NASA Astrophysics Data System (ADS)

Wilson, Christopher R.; Hutchens, Thomas C.; Hardy, Luke A.; Irby, Pierce B.; Fried, Nathaniel M.

2014-03-01

The Thulium fiber laser (TFL) is being explored as an alternative laser lithotripter to the Holmium:YAG laser. The TFL's superior near-single mode beam profile enables higher power transmission through smaller fibers with reduced proximal fiber tip damage. Recent studies have also reported that attaching hollow steel tubing to the distal fiber tip decreases fiber degradation and burn-back without compromising stone ablation rates. However, significant stone retropulsion was observed, which increased with pulse rate. In this study, the hollow steel tip fiber design was integrated with a stone basket to minimize stone retropulsion during ablation. A device was constructed consisting of a 100-μm-core, 140-μm-OD silica fiber outfitted with 5-mm-long stainless steel tubing at the distal tip, and integrated with a 1.3-Fr (0.433-mm-OD) disposable nitinol wire basket, to form an overall 1.9-Fr (0.633-mm- OD) integrated device. This compact design may provide several potential advantages including increased flexibility, higher saline irrigation rates through the ureteroscope working channel, and reduced fiber tip degradation compared to separate fiber and stone basket manipulation. TFL pulse energy of 31.5 mJ with 500 μs pulse duration and pulse rate of 500 Hz was delivered through the integrated fiber/basket device in contact with human uric acid stones, ex vivo. TFL stone ablation rates measured 1.5 +/- 0.2 mg/s, comparable to 1.7 +/- 0.3 mg/s (P > 0.05) using standard bare fiber tips separately with a stone basket. With further development, this device may be useful for minimizing stone retropulsion, thus enabling more efficient TFL lithotripsy at higher pulse rates.

Pigment gallstone pathogenesis: slime production by biliary bacteria is more important than beta-glucuronidase production.

PubMed

Stewart, L; Ponce, R; Oesterle, A L; Griffiss, J M; Way, L W

2000-01-01

Pigment stones are thought to form as a result of deconjugation of bilirubin by bacterial beta-glucuronidase, which results in precipitation of calcium bilirubinate. Calcium bilirubinate is then aggregated into stones by an anionic glycoprotein. Slime (glycocalyx), an anionic glycoprotein produced by bacteria causing foreign body infections, has been implicated in the formation of the precipitate that blocks biliary stents. We previously showed that bacteria are present within the pigment portions of gallstones and postulated a bacterial role in pigment stone formation through beta-glucuronidase or slime production. Ninety-one biliary bacterial isolates from 61 patients and 12 control stool organisms were tested for their production of beta-glucuronidase and slime. The average slime production was 42 for biliary bacteria and 2.5 for stool bacteria (P <0.001). Overall, 73% of biliary bacteria and 8% of stool bacteria produced slime (optical density >3). In contrast, only 38% of biliary bacteria produced beta-glucuronidase. Eighty-two percent of all patients, 90% of patients with common bile duct (CBD) stones, 100% of patients with primary CBD stones, and 93% of patients with biliary tubes had one or more bacterial species in their stones that produced slime. By comparison, only 47% of all patients, 60% of patients with CBD stones, 62% of patients with primary CBD stones, and 50% of patients with biliary tubes had one or more bacteria that produced beta-glucuronidase. Most biliary bacteria produced slime, and slime production correlated better than beta-glucuronidase production did with stone formation and the presence of biliary tubes or stents. Patients with primary CBD stones and biliary tubes had the highest incidence of slime production. These findings suggest that bacterial slime is important in gallstone formation and the blockage of biliary tubes.

Organic materials for ceramic molding processes

NASA Technical Reports Server (NTRS)

Saito, K.

1984-01-01

Ceramic molding processes are examined. Binders, wetting agents, lubricants, plasticizers, surface active agents, dispersants, etc., for pressing, rubber pressing, sip casting, injection casting, taping, extrusion, etc., are described, together with forming machines.

Die Soldering in Aluminium Die Casting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Q.; Kenik, E.A.; Viswanathan, S.

2000-03-15

Two types of tests, dipping tests and dip-coating tests were carried out on small steel cylinders using pure aluminum and 380 alloy to investigate the mechanism of die soldering during aluminum die casting. Optical and scanning electron microscopy were used to study the morphology and composition of the phases formed during soldering. A soldering mechanism is postulated based on experimental observations. A soldering critical temperature is postulated at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. When the temperature at the die surface is higher than this critical temperature, the aluminum-richmore » phase is liquid and joins the die with the casting during the subsequent solidification. The paper discusses the mechanism of soldering for the case of pure aluminum and 380 alloy casting in a steel mold, the factors that promote soldering, and the strength of the bond formed when soldering occurs. conditions, an aluminum-rich soldering layer may also form over the intermetallic layer. Although a significant amount of research has been conducted on the nature of these intermetallics, little is known about the conditions under which soldering occurs.« less

Method of fabricating a prestressed cast iron vessel

DOEpatents

Lampe, Robert F.

1982-01-01

A method of fabricating a prestressed cast iron vessel wherein double wall cast iron body segments each have an arcuate inner wall and a spaced apart substantially parallel outer wall with a plurality of radially extending webs interconnecting the inner wall and the outer wall, the bottom surface and the two exposed radial side surfaces of each body segment are machined and eight body segments are formed into a ring. The top surfaces and outer surfaces of the outer walls are machined and keyways are provided across the juncture of adjacent end walls of the body segments. A liner segment complementary in shape to a selected inner wall of one of the body segments is mounted to each of the body segments and again formed into a ring. The liner segments of each ring are welded to form unitary liner rings and thereafter the cast iron body segments are prestressed to complete the ring assembly. Ring assemblies are stacked to form the vessel and adjacent unitary liner rings are welded. A top head covers the top ring assembly to close the vessel and axially extending tendons retain the top and bottom heads in place under pressure.

Cystinuria

MedlinePlus

... rare condition in which stones made from an amino acid called cysteine form in the kidney, ureter, and ... Cystine is formed when two molecules of an amino acid called cysteine are bound together. The condition is ...

Coal gasification plant

DOEpatents

Wood, Andrew

1978-01-01

A removable annular hearth member, shaped to fit over the slag outlet of a slagging gasifier, comprises a cast body of high thermal conductivity having integral coolant passageways, said passageways being formed by shaping a metal tube into a coil having an inlet and an outlet, and casting metal to the desired shape around the coil such that the inlet and outlet communicate exteriorly of the cast body.

History of shock wave lithotripsy

NASA Astrophysics Data System (ADS)

Delius, Michael

2000-07-01

The first reports on the fragmentation of human calculi with ultrasound appeared in the fifties. Initial positive results with an extracorporeal approach with continuous wave ultrasound could, however, not be reproduced. A more promising result was found by generating the acoustic energy either in pulsed or continuous form directly at the stone surface. The method was applied clinically with success. Extracorporeal shock-wave generators unite the principle of using single ultrasonic pulses with the principle of generating the acoustic energy outside the body and focusing it through the skin and body wall onto the stone. Häusler and Kiefer reported the first successful contact-free kidney stone destruction by shock waves. They had put the stone in a water filled cylinder and generated a shock wave with a high speed water drop which was fired onto the water surface. To apply the new principle in medicine, both Häusler and Hoff's group at Dornier company constructed different shock wave generators for the stone destruction; the former used a torus-shaped reflector around an explosion wire, the latter the electrode-ellipsoid system. The former required open surgery to access the kidney stone, the latter did not. It was introduced into clinical practice after a series of experiments in Munich.

Citrate and renal calculi: an update

NASA Technical Reports Server (NTRS)

Pak, C. Y.

1994-01-01

Citrate is an inhibitor of the crystallization of stone-forming calcium salts. Hypocitraturia, frequently encountered in patients with nephrolithiasis, is therefore an important risk factor for stone formation. Potassium citrate provides physiological and physicochemical correction and inhibits new stone formation, not only in hypocitraturic calcium nephrolithiasis but also in uric acid nephrolithiasis. Inhibition of stone recurrence has now been validated by a randomized trial. Ongoing research has disclosed additional causes of hypocitraturia (sodium excess, low intestinal alkali absorption, but not primary citrate malabsorption). Moreover, new insights on potassium citrate action have been shown, notably that some of absorbed citrate escapes oxidation and contributes to the citraturic response, that ingestion with a meal does not sacrifice physiological or physicochemical action, that orange juice mimics but does not completely duplicate its actions, that potassium citrate may have a beneficial bone-sparing effect, that it may reduce stone fragments following ESWL, and that danger of aluminum toxicity is not great in subjects with functioning kidneys. Finally, the research on potassium citrate has led to two promising products, calcium citrate as an optimum calcium supplement and potassium-magnesium citrate which may be superior to potassium citrate in the management of stone disease.

A rare case of Mirizzi syndrome due to pure calcium carbonate stones (Limy Bile).

PubMed

Gilani, Nooman; Hanif, Muhammad Farooq; Karasek, Veronika

2016-06-01

We report the first case of Mirizzi syndrome in a patient who presented with biliary obstruction caused by pure calcium carbonate stones. A 61 years old male with history of portal vein thrombosis presented with rash, nausea and jaundice. An ultrasound of biliary tree showed gallstones with dilatation of hepatic duct and intrahepatic biliary tree. There was suspicion of a stone in proximal CBD. CT scan showed an opaque gallbladder with dense radio-opaque material in its lumen. An ERCP was then performed revealing external common hepatic duct obstruction at the neck of the gallbladder. A plastic biliary stent was placed across the obstruction, followed by a cholecystectomy. Resected gallbladder specimen revealed thick whitish paste like material, and formed stones filling the gallbladder lumen. Laboratory testing showed this material to be composed of 100% calcium carbonate crystals.

Personalized Intervention in Monogenic Stone Formers.

PubMed

Policastro, Lucas J; Saggi, Subodh J; Goldfarb, David S; Weiss, Jeffrey P

2017-10-20

Treatment of a first-time renal stone consists of acute management followed by medical efforts to prevent stone recurrence. Although nephrolithiasis is roughly 50% heritable, the presence of a family history usually does not affect treatment since most stone disease is regarded as polygenic, ie not attributable to a single gene. Recent evidence has suggested that single mutations could be responsible for a larger proportion of renal stones than previously thought. This intriguing possibility holds the potential to change the management paradigm in stone prevention from metabolically directed therapy to more specific approaches informed by genetic screening and testing. This review synthesizes new findings concerning monogenic kidney stone disease, and provides a concise and clinically useful reference for monogenic causes. It is expected that increased awareness of these etiologies will lead to increased use of genetic testing in recurrent stone formers and further research into the prevalence of monogenic stone disease. We assembled a complete list of genes known to cause or influence nephrolithiasis based on recent reviews and commentaries. We then comprehensively searched PubMed® and Google Scholar™ for all research on each gene having a pertinent role in nephrolithiasis. We determined which genes could be considered monogenic causes of nephrolithiasis. One gene, ALPL, was excluded since nephrolithiasis is a relatively minor aspect of the disorder associated with the gene (hypophosphatasia). We summarized selected studies and assembled clinically relevant details. A total of 27 genes were reviewed in terms of recent findings, mode of inheritance of stone disease, known or supposed prevalence of mutations in the general population of stone patients and specific therapies or considerations. There is a distinct opportunity for increased use of genetic testing to improve the lives of pediatric and adult stone patients. Several genes first reported in association with rare disease may be loci for novel mutations, heterozygous disease and forme frustes as causes of stones in the broader population. Cases of idiopathic nephrolithiasis should be considered as potentially having a monogenic basis. Copyright © 2018 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

A novel ultra-low carbon grain oriented silicon steel produced by twin-roll strip casting

NASA Astrophysics Data System (ADS)

Wang, Yang; Zhang, Yuan-Xiang; Lu, Xiang; Fang, Feng; Xu, Yun-Bo; Cao, Guang-Ming; Li, Cheng-Gang; Misra, R. D. K.; Wang, Guo-Dong

2016-12-01

A novel ultra-low carbon grain oriented silicon steel was successfully produced by strip casting and two-stage cold rolling method. The microstructure, texture and precipitate evolution under different first cold rolling reduction were investigated. It was shown that the as-cast strip was mainly composed of equiaxed grains and characterized by very weak Goss texture ({110}<001>) and λ-fiber (<001>//ND). The coarse sulfides of size 100 nm were precipitated at grain boundaries during strip casting, while nitrides remained in solution in the as-cast strip and the fine AlN particles of size 20-50 nm, which were used as grain growth inhibitors, were formed in intermediate annealed sheet after first cold rolling. In addition, the suitable Goss nuclei for secondary recrystallization were also formed during intermediate annealing, which is totally different from the conventional process that the Goss nuclei originated in the subsurface layer of the hot rolled sheet. Furthermore, the number of AlN inhibitors and the intensity of desirable Goss texture increased with increasing first cold rolling reduction. After secondary recrystallization annealing, very large grains of size 10-40 mm were formed and the final magnetic induction, B8, was as high as 1.9 T.

The effects of weld-repair and hot isostatic pressing on the fracture properties of Ti-5Al-2.5Sn ELI castings

NASA Technical Reports Server (NTRS)

Misra, M. S.; Lemeshewsky, S.; Bolstad, D.

1982-01-01

The Ti-5Al-2.5Sn extremely low interstitial alloy employed in the large castings which form the critical attachment fittings of the Space Shuttle External Tank was selected because of its high fracture resistance at cryogenic temperatures. Casting was selected over alternative fabrication methods because of its lower cost and adaptability to design changes, although it was found necessary to weld-repair surface and subsurface casting defects in order to reduce the scrap rate and maintain the inherent cost advantage of the castings. Hot Isostatic Pressing was experimentally found to heal the surface and internal defects of the castings, but did not improve tensile or fracture properties and was therefore rejected as a production technique. Production castings are instead weld-repaired, without any mechanical property degradation.

Method and mold for casting thin metal objects

DOEpatents

Pehrson, Brandon P; Moore, Alan F

2014-04-29

Provided herein are various embodiments of systems for casting thin metal plates and sheets. Typical embodiments include layers of mold cavities that are oriented vertically for casting the metal plates. In some embodiments, the mold cavities include a beveled edge such that the plates that are cast have a beveled edge. In some embodiments, the mold cavities are filled with a molten metal through an open horizontal edge of the cavity. In some embodiments, the mold cavities are filled through one or more vertical feed orifices. Further disclosed are methods for forming a thin cast metal plate or sheet where the thickness of the cast part is in a range from 0.005 inches to 0.2 inches, and the surface area of the cast part is in a range from 16 square inches to 144 square inches.

Method for casting thin metal objects

DOEpatents

Pehrson, Brandon P; Moore, Alan F

2015-04-14

Provided herein are various embodiments of systems for casting thin metal plates and sheets. Typical embodiments include layers of mold cavities that are oriented vertically for casting the metal plates. In some embodiments, the mold cavities include a beveled edge such that the plates that are cast have a beveled edge. In some embodiments, the mold cavities are filled with a molten metal through an open horizontal edge of the cavity. In some embodiments, the mold cavities are filled through one or more vertical feed orifices. Further disclosed are methods for forming a thin cast metal plate or sheet where the thickness of the cast part is in a range from 0.005 inches to 0.2 inches, and the surface area of the cast part is in a range from 16 square inches to 144 square inches.

Unusual Giant Prostatic Urethral Calculus

PubMed Central

Bello, A.; Maitama, H. Y.; Mbibu, N. H.; Kalayi, G. D.; Ahmed, A.

2010-01-01

Giant vesico-prostatic urethral calculus is uncommon. Urethral stones rarely form primarily in the urethra, and they are usually associated with urethral strictures, posterior urethral valve or diverticula. We report a case of a 32-year-old man with giant vesico-prostatic (collar-stud) urethral stone presenting with sepsis and bladder outlet obstruction. The clinical presentation, management, and outcome of the giant prostatic urethral calculus are reviewed. PMID:22091328

A new use of hydroxyapatite-based consolidant: cleaning and consolidation of stones in one step by reaction with gypsum crust

NASA Astrophysics Data System (ADS)

Molina Piernas, Eduardo; Rueda Quero, Lucia; Cultrone, Giuseppe; Ruiz Agudo, Encarnación

2015-04-01

The reaction between diammonium hydrogen phosphate (DAP) and calcite in the stone to form hydroxyapatite (HAP) had provided a new product to consolidate limestone or Ca-rich stones, for example sandstones with carbonatic cement. However, what does it happen with the stones without Ca-bearing compounds? Obviously, HAP cannot form. In the other hand, recent research about consolidation with DAP show a good interaction between carbonatic stones and HAP, improving their mechanical properties. For these reasons, we propose a new method for the consolidation of building stone capable of cleaning the gypsum crust and consolidating stones at the same time, based in the Ferroni-Dini method [1] and using DAP. Based on this method, we aim at obtaining a consolidating component reacting DAP (instead of ammonium carbonate) and the gypsum contained in the crust of weathered stones in polluted environments. As an advantage, we do not need to use barium hydroxide (the second step required in the Ferroni-Dini method), thereby reducing the time necessary to carry out the consolidation. Here, we report different tests to evaluate this new procedure. In a first set of experiments, a DAP solution was poured on a gypsum (dihydrate calcium sulphate) saturated solution and by monitoring the free calcium content of the solution using an ion-selective electrode we have evaluated the fluctuations in the content in calcium of the solution and the speed of the reaction. Once the reaction finished, we analyzed the solids formed to verify the formation of hydroxyapatite by FTIR and microRAMAN. The second test consisted in the alteration of limestone blocks with sulfuric acid to obtain a crust of gypsum and, after that, the samples were consolidated by means of cellulose compress soaked in DAP 3M during different reaction times (30 minutes, 1 hour and 4 hours, at controlled temperature -20 °C- and relative humidity -40% HR-). The samples were then analyzed by XRD, FTIR, microRAMAN and SEM-EDX to verify the formation of hydroxyapatite and the elimination of gypsum by transformation into ammonium sulphate (highly soluble). Our preliminary results show that the reaction occurs at room temperature in a short period of time. The amount of gypsum decreases with reaction time, while the amount of HAP significantly increases, with the gypsum being almost completely removed after 4 hours of reaction. We can conclude that this procedure is an optimal solution to remove the gypsum contained in the crust of the weathered stones and to consolidate them, independently of the mineralogical composition of the stone. Acknowledgements: This study was financially supported by Research Group RNM179 of the Junta de Andalucía and by the Research Project MAT2012-34473. [1] M. Matteini, "In review: An assessment of Florentine Methods of Wall Painting Conservation Based on the Use of Mineral Treatments", in "The Conservation of Wall Paintings: Proceedings of a Symposium organized by the Courtauld Institute of Art and the Getty Conservation Institute", London, 1987, pp. 137-146.

The performance of silk scaffolds in a rat model of augmentation cystoplasty.

PubMed

Seth, Abhishek; Chung, Yeun Goo; Gil, Eun Seok; Tu, Duong; Franck, Debra; Di Vizio, Dolores; Adam, Rosalyn M; Kaplan, David L; Estrada, Carlos R; Mauney, Joshua R

2013-07-01

The diverse processing plasticity of silk-based biomaterials offers a versatile platform for understanding the impact of structural and mechanical matrix properties on bladder regenerative processes. Three distinct groups of 3-D matrices were fabricated from aqueous solutions of Bombyx mori silk fibroin either by a gel spinning technique (GS1 and GS2 groups) or a solvent-casting/salt-leaching method in combination with silk film casting (FF group). SEM analyses revealed that GS1 matrices consisted of smooth, compact multi-laminates of parallel-oriented silk fibers while GS2 scaffolds were composed of porous (pore size range, 5-50 μm) lamellar-like sheets buttressed by a dense outer layer. Bi-layer FF scaffolds were comprised of porous foams (pore size, ~400 μm) fused on their external face with a homogenous, nonporous silk film. Silk groups and small intestinal submucosa (SIS) matrices were evaluated in a rat model of augmentation cystoplasty for 10 weeks of implantation and compared to cystotomy controls. Gross tissue evaluations revealed the presence of intra-luminal stones in all experimental groups. The incidence and size of urinary calculi was the highest in animals implanted with gel spun silk matrices and SIS with frequencies ≥57% and stone diameters of 3-4 mm. In contrast, rats augmented with FF scaffolds displayed substantially lower rates (20%) and stone size (2 mm), similar to the levels observed in controls (13%, 2 mm). Histological (hematoxylin and eosin, Masson's trichrome) and immunohistochemical (IHC) analyses showed comparable extents of smooth muscle regeneration and contractile protein (α-smooth muscle actin and SM22α) expression within defect sites supported by all matrix groups similar to controls. Parallel evaluations demonstrated the formation of a transitional, multi-layered urothelium with prominent uroplakin and p63 protein expression in all experimental groups. De novo innervation and vascularization processes were evident in all regenerated tissues indicated by Fox3-positive neuronal cells and vessels lined with CD31 expressing endothelial cells. In comparison to other biomaterial groups, cystometric analyses at 10 weeks post-op revealed that animals implanted with the FF matrix configuration displayed superior urodynamic characteristics including compliance, functional capacity, as well as spontaneous non voiding contractions consistent with control levels. Our data demonstrate that variations in scaffold processing techniques can influence the in vivo functional performance of silk matrices in bladder reconstructive procedures. Copyright © 2013 Elsevier Ltd. All rights reserved.

Gist of medicinal plants of Pakistan having ethnobotanical evidences to crush renal calculi (kidney stones).

PubMed

Nasim, Muhammad Jawad; Bin Asad, Muhammad Hassham Hassan; Durr-e-Sabih; Ikram, Raja Muhammad; Hussain, Muhammad Sikandar; Khan, Muhammad Tajammal; Ahamad, Ghafoor; Karim, Sabiha; Khan, Shujaat Ali; Murtaza, Ghulam

2014-01-01

Human civilization is facing the problem of kidney stones since ancient ages. Although mortality rate is not so high, yet it affects the victim's quality of life. The patient suffers from intense pain and many other symptoms modifying his life style and affecting his socioeconomic status. Many drugs and invasive methods have also been developed for the treatment, but these are highly costly and unaffordable for poor people and the rate of reoccurrence is also high. The use of medicinal plants is both affordable and effective in this respect. In this article, 35 medicinal plants of Pakistan origin and their crucial information have been enumerated in alphabetical order of plant's scientific name, family, place (distribution), part used, local name, habit, major constituents and references. It can also be seen that all parts are used for the treatment of kidney stones. Leaves represent 28% contribution, whole plants and seeds 12%, fruits and roots 11% contribution in this respect. Flowers contribute 8% in the treatment of kidney stone while branches, bark, bushes, buds, milk and shoots contribute only 3% in the removal of kidney stones. Habits of plants were also taken under consideration. It was noticed that herbs are the most useful life form in this regard which contributed 63% for the removal of kidney stone. Shrubs contributed 20%, trees 11% while bushes and weeds contributed 3% for the removal of kidney stones.

Educational utilization of outstanding spherulitic rhyolite occurred in Cheongsong, Korea

NASA Astrophysics Data System (ADS)

Jang, Y. D.; Woo, H.

2015-12-01

Cheongsong is located in the central eastern area of South Korea. Unique spherulitic rhyolites occur in this region as dykes formed about 48 to 50 million years ago. Composed of quartz and feldspar these spherulitic rhyolites show various flowerlike shapes, such as chrysanthemum, dandelion, rose, carnation, sunflower, dahlia and so on, so they are called 'flower stones'. The spherulite indicates that it was undercooled caused by very fast cooling at a shallow depth near the surface and the variety of shapes resulted from the difference of crystallizing conditions. According to the condition, minerals start to crystallize homogeneously or heterogeneously and develop as rounded or fibrous shapes, representing beautiful patterns when combined. These spherulitic structures are very rare not only in Korea but also globally, being valuable for research and preservation because of their rarity, beauty and diversity. Cheongsong therefore applies to the UGG (UNESCO Global Geopark) in an attempt to popularize the flower stones and use them as education materials which can also be incorporated in other valuable sites. The exhibition center provides diverse types of flower stones in which visitors could learn about rhyolitic volcanism, crystallization and spherulite and can experience the process of changing a rough stone into a flower stone. A geotrail course has also been created, showing each type of flower stone on the outcrop and providing educational programs about geological mechanisms of the stones with a trained guide.

The Initial Appearance of Ashlar Stone in Cyprus. éssues of Provenance and Use

NASA Astrophysics Data System (ADS)

Philokyprou, M.

In Cyprus stone was the primary building material, either as rubble or in a dressed form (called ashlar), since the Neolithic period. Initially stone was used only as rubble but later during the Late Brone Age ashlar stone appeared for the first time on the island. The aim of this paper is the presentation of the results of a systematic research regarding the different types and uses of ashlar stone and the techniques followed during the Late Bronze Age in Cyprus in comparison with other Mediterranean areas. The macroscopic and microscopic examination of selected samples showed that sedimentary rocks of various geological formations were used as ashlars. One, two or even three different types of stones were transported from the quarries nearest to the settlements. Some characteristic methods of stone dressing, such as finishing only the visible faces and creating drafted margins around the face of the ashlar blocks, are to be found not only in Late Bronze Age settlements but also in more recent examples from the last two centuries. The choice of ashlar and the methods of construction can be related to social, religious and political factors and were not only based on aesthetic criteria and practical issues. Thus, the most impressive structural solutions were followed in the construction of temples and public buildings, whereas more simple methods can be observed in residential complexes.

Mold with improved core for metal casting operation

DOEpatents

Gritzner, Verne B.; Hackett, Donald W.

1977-01-01

The present invention is directed to a mold containing an improved core for use in casting hollow, metallic articles. The core is formed of, or covered with, a layer of cellular material which possesses sufficient strength to maintain its structural integrity during casting, but will crush to alleviate the internal stresses that build up if the normal contraction during solidification and cooling is restricted.

Type of Primary Nb₅Si₃ and Precipitation of Nbss in αNb₅Si₃ in a Nb-8.3Ti-21.1Si-5.4Mo-4W-0.7Hf (at.%) Near Eutectic Nb-Silicide-Based Alloy.

PubMed

McCaughey, Conor; Tsakiropoulos, Panos

2018-06-07

The Nb-silicide-based alloy of near eutectic composition (at.%) Nb-21.1Si-8.3Ti-5.4Mo-4W-0.7Hf (alloy CM1) was studied in the cast and heat-treated (1500 °C/100 h) conditions. The alloy was produced in the form of buttons and bars using three different methods, namely arc-melting, arc-melting and suction casting, and optical floating zone (OFZ) melting. In the former two cases the alloy solidified in water-cooled copper crucibles. Buttons and suction-cast bars of different size, respectively of 10 g and 600 g weight and 6 mm and 8 mm diameter, were produced. The OFZ bars were grown at three different growth rates of 12, 60 and 150 mm/h. It was confirmed that the type of Nb₅Si₃ formed in the cast microstructures depended on the solidification conditions. The primary phase in the alloy CM1 was the βNb₅Si₃. The transformation of βNb₅Si₃ to αNb₅Si₃ had occurred in the as cast large size button and the OFZ bars grown at the three different growth rates, and after the heat treatment of the small size button and the suction-cast bars of the alloy. This transformation was accompanied by subgrain formation in Nb₅Si₃ and the precipitation of Nb ss in the large size as cast button and only by the precipitation of Nb ss in the cast OFZ bars. Subgrains and precipitation of Nb ss in αNb₅Si₃ was observed in the small size button and suction-cast bars after the heat treatment. Subgrains formed in αNb₅Si₃ after the heat treatment of the OFZ bars. The partitioning of solutes and in particular of Mo and Ti was key to this phase transformation. Subgrain formation was not necessary for precipitation of Nb ss in αNb₅Si₃, but the partitioning of solutes was essential for this precipitation.

Biomimetic Materials by Freeze Casting

NASA Astrophysics Data System (ADS)

Porter, Michael M.; Mckittrick, Joanna; Meyers, Marc A.

2013-06-01

Natural materials, such as bone and abalone nacre, exhibit exceptional mechanical properties, a product of their intricate microstructural organization. Freeze casting is a relatively simple, inexpensive, and adaptable materials processing method to form porous ceramic scaffolds with controllable microstructural features. After infiltration of a second polymeric phase, hybrid ceramic-polymer composites can be fabricated that closely resemble the architecture and mechanical performance of natural bone and nacre. Inspired by the narwhal tusk, magnetic fields applied during freeze casting can be used to further control architectural alignment, resulting in freeze-cast materials with enhanced mechanical properties.

Clinical value of crystalluria and quantitative morphoconstitutional analysis of urinary calculi.

PubMed

Frochot, Vincent; Daudon, Michel

2016-12-01

Crystalluria is a marker of urine supersaturation with substances deriving from metabolic disorders, inherited diseases or drugs. The investigation of crystalluria must be done according to a protocol which includes the delivery to the laboratory of a proper urine sample, the use of a microscope equipped with polarized light, the accurate knowledge of urine pH, and a comprehensive examination of the crystals, which is based on their identification, quantification and size measurement. For unusual crystals, infrared spectroscopy may also be needed. If the formation of stones is always preceded by crystalluria, the reverse is not true. In addition to the crystalline composition, stone morphology provides valuable information on stone activity and, for some crystalline species, major information regarding the underlying pathology. Fourier transform infrared spectroscopy (FTIR) reliably identify specific forms of nephrolithiasis, as common-type stones made of calcium oxalate (CaOx) and/or calcium phosphate that is combined with morphology classification; using this method, stones may be classified into 6 types subdivided in 22 subtypes. The investigation of crystalluria is an inexpensive and valuable tool for the detection and the monitoring of inherited and acquired diseases associated with urinary stone formation or acute or chronic renal function impairment from intrarenal crystal precipitation. Selective FTIR identification of the composition of core (or the umbilication), middle part, and surface of every stone allows identification of the initiating lithogenic process (in the nucleus or in the Randall's plaque) and the factors which subsequently contributed to stone growth. In conclusion, the proposed morpho-constitutional method of urinary stone analysis, which moreover is rapid and low cost, provides clinically relevant orientations for targeted etiologic evaluation. Copyright © 2016 IJS Publishing Group Ltd. Published by Elsevier Ltd. All rights reserved.

Microorganisms and calcium oxalate stone disease.

PubMed

Goldfarb, David S

2004-01-01

Microorganisms may have a role in the pathogenesis and prevention of kidney stones. The subjects of this review include nanobacteria, Oxalobacter formigenes, and lactic acid bacteria. Not reviewed here is the well-described role of infections of the urinary tract with Proteus species and other urease-producing organisms associated with struvite stone formation. Nanobacteria have been proposed to be very small (0.08-0.5 nm), ubiquitous organisms that could play a role in stone formation. The theory is that nanobacteria can nucleate carbonate apatite on their surfaces and thereby provide the nidus for stone formation. However, their existence remains uncertain and many investigators are openly skeptical. Recent investigations suggest that they are artifacts, and not actually living organisms, but their proponents continue to study them. O. formigenes is an obligate anaerobe which may be important in the prevention of stone formation. Its sole substrate for generation of ATP is oxalate. It may thereby metabolize its human host's dietary oxalate and diminish intestinal absorption and subsequent urinary excretion of oxalate. There is evidence that the organism's absence, perhaps sometimes due to courses of antibiotics, may be a cause of hyperoxaluria and stone formation. In early investigations, patients not colonized with the organism can be recolonized. Urinary oxalate can be diminished by accompanying an oxalate-containing meal with the organism. One study demonstrated that a preparation of lactic acid bacteria successfully reduced urinary oxalate excretion in 6 patients with calcium oxalate stones and hyperoxaluria. The mechanism of this effect is uncertain since these bacteria lacked the gene possessed by O. formigenes which codes for that organism's oxalate uptake mechanism. The author is currently completing a small randomized controlled clinical trial with this preparation in calcium stone-forming patients with idiopathic hyperoxaluria. Copyright (c) 2004 S. Karger AG, Basel.

Evidence Report: Risk of Renal Stone Formation

NASA Technical Reports Server (NTRS)

Sibonga, Jean D.; Pietrzyk, Robert

2017-01-01

The formation of renal stones poses an in-flight health risk of high severity, not only because of the impact of renal colic on human performance but also because of complications that could potentially lead to crew evacuation, such as hematuria, infection, hydronephrosis, and sepsis. Evidence for risk factors comes from urine analyses of crewmembers, documenting changes to the urinary environment that are conducive to increased saturation of stone-forming salts, which are the driving force for nucleation and growth of a stone nidus. Further, renal stones have been documented in astronauts after return to Earth and in one cosmonaut during flight. Biochemical analysis of urine specimens has provided indication of hypercalciuria and hyperuricemia, reduced urine volumes, and increased urine saturation of calcium oxalate and calcium phosphate. A major contributor to the risk for renal stone formation is bone atrophy with increased turnover of the bone minerals. Dietary and fluid intakes also play major roles in the risk because of the influence on urine pH (more acidic) and on volume (decreased). Historically, specific assessments on urine samples from some Skylab crewmembers indicated that calcium excretion increased early in flight, notable by day 10 of flight, and almost exceeded the upper threshold for normal excretion (300mg/day in males). Other crewmember data documented reduced intake of fluid and reduced intake of potassium, phosphorus, magnesium, and citrate (an inhibitor of calcium stone formation) in the diet. Hence, data from both short-duration and long-duration missions indicate that space travel induces risk factors for renal stone formation that continue to persist after flight; this risk has been documented by reported kidney stones in crewmembers.

Sticks and Stones Can Break My Bones but Labels Scar My Soul.

PubMed

Seitler, Burton Norman

2014-09-01

Influenced by the followers of Descartes several centuries ago, philosophy, science and society took a turn in the road, one that has lead us astray. Mind was separated and cast away from its body, and so-called rationalism, reductionism and mechanism soon held sway over holism and humanism. Individuals were swept up, homogenized and subsumed under the provenance of arbitrarily created group norms for conduct. Those who did not follow were marginalized, or worse, demonized. Individuality, now being lost, inexorably would be replaced by all-encompassing clinical labels, that furthered the dehumanizing process begun and enforced so long ago. A new dialectic about the human circumstance based on humanism, empathy, understanding and respect, is proposed. © 2014 Journal of Pastoral Care Publications Inc.

Digital vs. conventional full-arch implant impressions: a comparative study.

PubMed

Amin, Sarah; Weber, Hans Peter; Finkelman, Matthew; El Rafie, Khaled; Kudara, Yukio; Papaspyridakos, Panos

2017-11-01

To test whether or not digital full-arch implant impressions with two different intra-oral scanners (CEREC Omnicam and True Definition) have the same accuracy as conventional ones. The hypothesis was that the splinted open-tray impressions would be more accurate than digital full-arch impressions. A stone master cast representing an edentulous mandible using five internal connection implant analogs (Straumann Bone Level RC, Basel, Switzerland) was fabricated. The three median implants were parallel to each other, the far left implant had 10°, and the far right had 15° distal angulation. A splinted open-tray technique was used for the conventional polyether impressions (n = 10) for Group 1. Digital impressions (n = 10) were taken with two intra-oral optical scanners (CEREC Omnicam and 3M True Definition) after connecting polymer scan bodies to the master cast for groups 2 and 3. Master cast and conventional impression test casts were digitized with a high-resolution reference scanner (Activity 880 scanner; Smart Optics, Bochum, Germany) to obtain digital files. Standard tessellation language (STL) datasets from the three test groups of digital and conventional impressions were superimposed with the STL dataset from the master cast to assess the 3D deviations. Deviations were recorded as root-mean-square error. To compare the master cast with conventional and digital impressions at the implant level, Welch's F-test was used together with Games-Howell post hoc test. Group I had a mean value of 167.93 μm (SD 50.37); Group II (Omnicam) had a mean value of 46.41 μm (SD 7.34); Group III (True Definition) had a mean value of 19.32 μm (SD 2.77). Welch's F-test was used together with the Games-Howell test for post hoc comparisons. Welch's F-test showed a significant difference between the groups (P < 0.001). The Games-Howell test showed statistically significant 3D deviations for all three groups (P < 0.001). Full-arch digital implant impressions using True Definition scanner and Omnicam were significantly more accurate than the conventional impressions with the splinted open-tray technique. Additionally, the digital impressions with the True Definition scanner had significantly less 3D deviations when compared with the Omnicam. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Ni{sub 3}Al technology transfer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sikka, V.K.; Viswanathan, S.; Santella, M.L.

1997-04-01

Ductile Ni{sub 3}Al and Ni{sub 3}Al-based alloys have been identified for a range of applications. These applications require the use of material in a variety of product forms such as sheet, plate, bar, wire, tubing, piping, and castings. Although significant progress has been made in the melting, casting, and near-net-shape forming of nickel aluminides, some issues still remain. These include the need for: (1) high-strength castable composition for many applications that have been identified; (2) castability (mold type, fluidity, hot-shortness, porosity, etc.); (3) weld reparability of castings; and (4) workability of cast or powder metallurgy product to sheet, bar, andmore » wire. The four issues listed above can be {open_quotes}show stoppers{close_quotes} for the commercial application of nickel aluminides. This report describes the work completed to address some of these issues during FY 1996.« less

A comparative study of gallstones from children and adults using FTIR spectroscopy and fluorescence microscopy

PubMed Central

Kleiner, Oleg; Ramesh, Jagannathan; Huleihel, Mahmoud; Cohen, Beny; Kantarovich, Keren; Levi, Chen; Polyak, Boris; Marks, Robert S; Mordehai, Jacov; Cohen, Zahavi; Mordechai, Shaul

2002-01-01

Background Cholelithiasis is the gallstone disease (GSD) where stones are formed in the gallbladder. The main function of the gallbladder is to concentrate bile by the absorption of water and sodium. GSD has high prevalence among elderly adults. There are three major types of gallstones found in patients, White, Black and Brown. The major chemical component of white stones is cholesterol. Black and brown stones contain different proportions of cholesterol and bilirubin. The pathogenesis of gallstones is not clearly understood. Analysis of the chemical composition of gallstones using various spectroscopic techniques offers clues to the pathogenesis of gallstones. Recent years has seen an increasing trend in the number of cases involving children. The focus of this study is on the analysis of the chemical composition of gallstones from child and adult patients using spectroscopic methods. Methods In this report, we present FTIR spectroscopic studies and fluorescence microscopic analysis of gallstones obtained from 67 adult and 21 child patients. The gallstones were removed during surgical operations at Soroka University Medical Center. Results Our results show that black stones from adults and children are rich in bilirubin. Brown stones are composed of varying amounts of bilirubin and cholesterol. Green stones removed from an adult, which is rare, was found to be composed mainly of cholesterol. Our results also indicated that cholesterol and bilirubin could be the risk factors for gallstone formation in adults and children respectively. Fluorescence micrographs showed that the Ca-bilirubinate was present in all stones in different quantities and however, Cu-bilirubinate was present only in the mixed and black stones. Conclusions Analysis based on FTIR suggest that the composition of black and brown stones from both children and adults are similar. Various layers of the brown stone from adults differ by having varying quantities of cholesterol and calcium carbonate. Ring patterns observed mainly in the green stone using fluorescence microscopy have relevance to the mechanism of the stone formation. Our preliminary study suggests that bilirubin and cholesterol are the main risk factors of gallstone disease. PMID:11872150

Hydrophobizing coatings for cultural heritage. A detailed study of resin/stone surface interaction

NASA Astrophysics Data System (ADS)

Fermo, P.; Cappelletti, G.; Cozzi, N.; Padeletti, G.; Kaciulis, S.; Brucale, M.; Merlini, M.

2014-07-01

Conservation of historical buildings is an important issue and the environmental conditions seriously affect the monument's stones. The protection of cultural heritage buildings and monuments by surface treatment with polymers is a common practice due to their ability to form a protective layer on the monument's surface as well as to control the transport of different fluids from the surface to the monument's interior. In this work, three different substrates were used: Carrara marble, Botticino limestone, and Angera stone. A commercially available Si-based resin (Alpha®SI30) was used as protective agent to improve the hydrophobicity features of the different tested materials. The surface properties of the coating and the relative interaction with the adopted stones were studied using different techniques such as contact angle measurements, electron microscope coupled with an energy dispersive spectrometer, X-ray photoelectron spectroscopy, atomic force microscopy, and attenuated total reflection infrared spectroscopy.

A comparative study of the accuracy between plastic and metal impression transfer copings for implant restorations.

PubMed

Fernandez, Monica A; Paez de Mendoza, Carmen Y; Platt, Jeffrey A; Levon, John A; Hovijitra, Suteera T; Nimmo, Arthur

2013-07-01

A precise transfer of the position and orientation of the antirotational mechanism of an implant to the working cast is particularly important to achieve optimal fit of the final restoration. This study evaluated and compared the accuracy of metal and plastic impression copings for use in a full-arch mandibular edentulous simulation with four implants. Metal and plastic impression transfer copings for two implant systems, Nobel Biocare™ Replace and Straumann SynOcta®, were assessed on a laboratory model to simulate clinical practice. The accuracy of producing stone casts using these plastic and metal impression transfer copings was measured against a standard prosthetic framework consisting of a cast gold bar. A total of 20 casts from the four combinations were obtained. The fit of the framework on the cast was tested by a noncontact surface profilometer, the Proscan 3D 2000 A, using the one-screw test. The effects of implant/system and impression/coping material on gap measurements were analyzed using repeated measures ANOVA. The findings of this in vitro study were as follows: plastic copings demonstrated significantly larger average gaps than metal for Straumann (p = 0.001). Plastic and metal copings were not significantly different for Nobel (p = 0.302). Nobel had significantly larger average gaps than Straumann for metal copings (p = 0.003). Nobel had marginally smaller average gaps than Straumann (p = 0.096) for plastic copings. The system-by-screw location interaction was significant as well (p < 0.001), indicating significant differences among the four screw locations, but the location differences were not the same for the two systems. A rank transformation of the data was necessary due to the nonnormal distribution of the gap measurements. No adjustments were made for multiple comparisons. The metal impression copings were more accurate than plastic copings when using the Straumann system, and there was no difference between metal and plastic copings for the Nobel Replace system. The system-by-screw location was not conclusive, showing no correlation within each system. © 2013 by the American College of Prosthodontists.

Queering the cosmology of the vikings: a queer analysis of the cult of Odin and "holy white stones".

PubMed

Solli, Brit

2008-01-01

Ideas concerning Eros, honor and death were central to the Norse perception of the world. Odin is the greatest war god, and associated with manliness. However, Odin is also the most powerful master of seid (sorcery), an activity associated with women. Seid may be interpreted as a form of shamanism. If a man performed seid he could be accused of ergi, that is, unmanliness. Therefore it could be said that Odin exercised an activity considered unmanly. How could Odin perform seid without losing his position as the god of war and warriors? This paradox is discussed from a queer theoretical perspective. On this basis a new interpretation of the so-called "holy white" phallic stones in western Norway is suggested. Most of these stones are associated with burials from the later part of the Scandinavian Early Iron Age. The temporal distribution of the white phallic stones correlates well with the increasing importance of the cult of Odin. There may be a cultic association between the cult of Odin and the burial practices involving white holy phallic stones.

Evaluation of Uranium-235 Measurement Techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaspar, Tiffany C.; Lavender, Curt A.; Dibert, Mark W.

2017-05-23

Monolithic U-Mo fuel plates are rolled to final fuel element form from the original cast ingot, and thus any inhomogeneities in 235U distribution present in the cast ingot are maintained, and potentially exaggerated, in the final fuel foil. The tolerance for inhomogeneities in the 235U concentration in the final fuel element foil is very low. A near-real-time, nondestructive technique to evaluate the 235U distribution in the cast ingot is required in order to provide feedback to the casting process. Based on the technical analysis herein, gamma spectroscopy has been recommended to provide a near-real-time measure of the 235U distribution inmore » U-Mo cast plates.« less

Process for manufacturing a lithium alloy electrochemical cell

DOEpatents

Bennett, William R.

1992-10-13

A process for manufacturing a lithium alloy, metal sulfide cell tape casts slurried alloy powders in an organic solvent containing a dissolved thermoplastic organic binder onto casting surfaces. The organic solvent is then evaporated to produce a flexible tape removable adhering to the casting surface. The tape is densified to increase its green strength and then peeled from the casting surface. The tape is laminated with a separator containing a lithium salt electrolyte and a metal sulfide electrode to form a green cell. The binder is evaporated from the green cell at a temperature lower than the melting temperature of the lithium salt electrolyte. Lithium alloy, metal sulfide and separator powders may be tape cast.

Method of forming components for a high-temperature secondary electrochemical cell

DOEpatents

Mrazek, Franklin C.; Battles, James E.

1983-01-01

A method of forming a component for a high-temperature secondary electrochemical cell having a positive electrode including a sulfide selected from the group consisting of iron sulfides, nickel sulfides, copper sulfides and cobalt sulfides, a negative electrode including an alloy of aluminum and an electrically insulating porous separator between said electrodes. The improvement comprises forming a slurry of solid particles dispersed in a liquid electrolyte such as the lithium chloride-potassium chloride eutetic, casting the slurry into a form having the shape of one of the components and smoothing the exposed surface of the slurry, cooling the cast slurry to form the solid component, and removing same. Electrodes and separators can be thus formed.

Laparoscopic management of CBD stones: an Indian experience.

PubMed

Chander, Jagdish; Vindal, Anubhav; Lal, Pawanindra; Gupta, Nikhil; Ramteke, Vinod Kumar

2011-01-01

Common bile duct stones (CBDS) that are seen in the Asian population are very different from those seen in the west. It is not infrequent to see multiple, large, and impacted stones and a hugely dilated CBD. Many of these patients have been managed by open CBD exploration (OCBDE), even after the advent of laparoscopic cholecystectomy (LC), because these large stones pose significant challenges for extraction by endoscopic retrograde cholangiopancreatography. This series presents the largest experience of managing CBDS using a laparoscopic approach from Indian subcontinent. Between 2003 and 2009, 150 patients with documented CBDS were treated laparoscopically at a tertiary care hospital in New Delhi. Of these, 4 patients were managed through transcystic route and 140 through the transcholedochal route. There were 34 men and 116 women patients with age ranging from 15 to 72 years. The mean size of the CBD on ultrasound was 11.7 ± 3.7 mm and on MRCP 13.8 ± 4.7 mm. The number of stones extracted varied from 1 to 70 and the size of the extracted stones from 5 to 30 mm. The average duration of surgery was 139.9 ± 26.3 min and the mean intraoperative blood loss was 103.4 ± 85.9 ml. There were 6 conversions to open procedures, 1 postoperative death (0.7%), and 23 patients (15%) had nonfatal postoperative complications. Three patients had retained stones (2%) and one developed recurrent stone (0.7%). Even in patients with multiple, large, and impacted CBDS, there is scope for a minimally invasive procedure with its attendant benefits in the form of laparoscopic CBD exploration (LCBDE).

Sex differences in the stone tool-use behavior of a wild population of burmese long-tailed macaques (Macaca fascicularis aurea).

PubMed

Gumert, Michael D; Hoong, Low Kuan; Malaivijitnond, Suchinda

2011-12-01

We investigated sex differences in how Burmese long-tailed macaques (Macaca fascicularis aurea) used stone tools to open shelled food items along the shores of two islands in Laemson National Park, Thailand. Over a 2-week period in December 2009, we collected scan and focal samples on macaques when they were visible along the shores and mangroves. We found females used stones more often while feeding and used smaller tools than males. Females also processed sessile oysters more than males, whereas males processed unattached foods more than females. It was unclear which sex was overall more proficient at stone tool use, but males did perform significantly better at opening unattached food items with large pounding stones. Females also struck food items more times during tool-use bouts and at a faster rate, but no significant difference was found in average tool-use bout duration. Males processed foods slightly faster within a tool-use bout, but we were unable to detect a significant difference in the rate of food processing while foraging with tools. In summary females chipped open sessile oysters with an axing technique more than males, while males used larger stones to pound open unattached shelled food more often than females. Despite using pounding more than females, males also regularly utilized the axing technique on sessile oysters. Our results are the first assessment of sex differences in macaque stone tool use, providing a basis for comparison with tool use in other primates, and to nonfunctional forms of stone use in other macaques. © 2011 Wiley Periodicals, Inc.

Effect of Potassium Citrate on Calcium Phosphate Stones in a Model of Hypercalciuria

PubMed Central

Asplin, John R.; Frick, Kevin K.; Granja, Ignacio; Culbertson, Christopher D.; Ng, Adeline; Grynpas, Marc D.; Bushinsky, David A.

2015-01-01

Potassium citrate is prescribed to decrease stone recurrence in patients with calcium nephrolithiasis. Citrate binds intestinal and urine calcium and increases urine pH. Citrate, metabolized to bicarbonate, should decrease calcium excretion by reducing bone resorption and increasing renal calcium reabsorption. However, citrate binding to intestinal calcium may increase absorption and renal excretion of both phosphate and oxalate. Thus, the effect of potassium citrate on urine calcium oxalate and calcium phosphate supersaturation and stone formation is complex and difficult to predict. To study the effects of potassium citrate on urine supersaturation and stone formation, we utilized 95th-generation inbred genetic hypercalciuric stone-forming rats. Rats were fed a fixed amount of a normal calcium (1.2%) diet supplemented with potassium citrate or potassium chloride (each 4 mmol/d) for 18 weeks. Urine was collected at 6, 12, and 18 weeks. At 18 weeks, stone formation was visualized by radiography. Urine citrate, phosphate, oxalate, and pH levels were higher and urine calcium level was lower in rats fed potassium citrate. Furthermore, calcium oxalate and calcium phosphate supersaturation were higher with potassium citrate; however, uric acid supersaturation was lower. Both groups had similar numbers of exclusively calcium phosphate stones. Thus, potassium citrate effectively raises urine citrate levels and lowers urine calcium levels; however, the increases in urine pH, oxalate, and phosphate levels lead to increased calcium oxalate and calcium phosphate supersaturation. Potassium citrate induces complex changes in urine chemistries and resultant supersaturation, which may not be beneficial in preventing calcium phosphate stone formation. PMID:25855777

Form and function in the Lower Palaeolithic: history, progress, and continued relevance.

PubMed

Key, Alastair; Stephen, Lycett

2017-12-30

Percussively flaked stone artefacts constitute a major source of evidence relating to hominin behavioural strategies and are, essentially, a product or byproduct of a past individual's decision to create a tool with respect to some broader goal. Moreover, it has long been noted that both differences and recurrent regularities exist within and between Palaeolithic stone artefact forms. Accordingly, archaeologists have frequently drawn links between form and functionality, with functional objectives and performance often being regarded consequential to a stone tool's morphological properties. Despite these factors, extensive reviews of the related concepts of form and function with respect to the Lower Palaeolithic remain surprisingly sparse. We attempt to redress this issue. First we stress the historical place of form-function concepts, and their role in establishing basic ideas that echo to this day. We then highlight methodological and conceptual progress in determining artefactual function in more recent years. Thereafter, we evaluate four specific issues that are of direct consequence for evaluating the ongoing relevance of form-function concepts, especially with respect to their relevance for understanding human evolution more generally. Our discussion highlights specifically how recent developments have been able to build on a long historical legacy, and demonstrate that direct, indirect, experimental, and evolutionary perspectives intersect in crucial ways, with each providing specific but essential insights for ongoing questions. We conclude by emphasising that our understanding of these issues and their interaction, has been, and will be, essential to accurately interpret the Lower Palaeolithic archaeological record, tool-form related behaviours of Lower Palaeolithic hominins, and their consequences for (and relationship to) wider questions of human evolution.

The influence of maternal and paternal history on stone composition and clinical course of calcium nephrolithiasis in subjects aged between 15 and 25.

PubMed

Guerra, Angela; Ticinesi, Andrea; Allegri, Franca; Nouvenne, Antonio; Pinelli, Silvana; Folesani, Giuseppina; Lauretani, Fulvio; Maggio, Marcello; Borghi, Loris; Meschi, Tiziana

2016-11-01

Our aim was to compare the influence of maternal history of stones (MHS) and paternal history of stones (PHS) on composition of calculi and disease course in a group of patients with calcium nephrolithiasis (CN) aged between 15 and 25, the age range with the maximal influence of family history on disease expression. One-hundred thirty-five patients (68 F) with CN and one stone-forming parent were retrospectively selected from the database of our outpatient stone clinic, and categorized according to MHS or PHS. Data about stone disease course and composition of passed calculi, determined by chemical analysis or Fourier-transformed infrared spectrophotometry, were collected together with information on blood chemistry and 24-h urinary profile of lithogenic risk. The characteristics of disease course and stone composition were compared using logistic regression tests adjusted for age, sex, and BMI or analysis of covariance where appropriate. Patients with MHS (n = 46) had significantly higher urinary calcium/creatinine ratio and ammonium, a higher prevalence of urological treatments (57 vs 27 %, p < 0.001) and mixed calcium oxalate/calcium phosphate stone composition (69 vs 35 %, p = 0.002) than those with PHS. At multivariate logistic regression models, MHS was independently associated with urological treatments (OR 4.5, 95 %CI 1.9-10.7, p < 0.001) and the formation of calculi with mixed calcium oxalate/calcium phosphate composition (OR 5.8, 95 %CI 1.9-17.9, p = 0.002). The method of stone analysis did not affect this result. In conclusion, in subjects aged 15-25, MHS is associated with mixed calcium stones and with a higher risk for urological procedures, and should be, therefore, considered in the management of urolithiasis.

Use of Potassium Citrate to Reduce the Risk of Renal Stone Formation During Spaceflight

NASA Technical Reports Server (NTRS)

Whitson, P. A.; Pietrzyk, R. A.; Sams, C. F.; Jones, J. A.; Nelman-Gonzalez, M.; Hudson, E. K.

2008-01-01

Introduction: NASA s Vision for Space Exploration centers on exploration class missions including the goals of returning to the moon and landing on Mars. One of NASA s objectives is to focus research on astronaut health and the development of countermeasures that will protect crewmembers during long duration voyages. Exposure to microgravity affects human physiology and results in changes in the urinary chemical composition favoring urinary supersaturation and an increased risk of stone formation. Nephrolithiasis is a multifactorial disease and development of a renal stone is significantly influenced by both dietary and environmental factors. Previous results from long duration Mir and short duration Shuttle missions have shown decreased urine volume, pH, and citrate levels and increased calcium. Citrate, an important inhibitor of calcium-containing stones, binds with urinary calcium reducing the amount of calcium available to form stones. Citrate inhibits renal stone recurrence by preventing crystal growth, aggregation, and nucleation and is one of the most common therapeutic agents used to prevent stone formation. Methods: Thirty long duration crewmembers (29 male, 1 female) participated in this study. 24-hour urines were collected and dietary monitoring was performed pre, in, and postflight. Crewmembers in the treatment group received two potassium citrate (KCIT) pills, 10 mEq/pill, ingested daily beginning 3 days before launch, all inflight days and through 14 days postflight. Urinary biochemical and dietary analyses were completed. Results: KCIT treated subjects exhibited decreased urinary calcium excretion and maintained the levels of calcium oxalate supersaturation risk at their preflight levels. The increased urinary pH levels in these subjects reduced the risk of uric acid stones. Discussion: The current study investigated the use of potassium citrate as a countermeasure to minimize the risk of stone formation during ISS missions. Results suggest that supplementation with potassium citrate decreases the risk of stone formation during and immediately after spaceflight.

Renal Stone Risk during Spaceflight: Assessment and Countermeasure Validation

NASA Technical Reports Server (NTRS)

Whitson, Peggy A.; Pietrzyk, Robert A.; Jones, Jeffery A.; Sams, Clarence F.; Hudson, Ed K.; Nelman-Gonzalez, Mayra

2009-01-01

NASA's Vision for Space Exploration centers on exploration class missions including the goals of returning to the moon and landing on Mars. One of NASA's objectives is to focus research on astronaut health and the development of countermeasures that will protect crewmembers during long duration voyages. Exposure to microgravity affects human physiology and results in changes in the urinary chemical composition favoring urinary supersaturation and an increased risk of stone formation. Nephrolithiasis is a multifactorial disease and development of a renal stone is significantly influenced by both dietary and environmental factors. Previous results from long duration Mir and short duration Shuttle missions have shown decreased urine volume, pH, and citrate levels and increased calcium. Citrate, an important inhibitor of calcium-containing stones, binds with urinary calcium reducing the amount of calcium available to form stones. Citrate inhibits renal stone recurrence by preventing crystal growth, aggregation, and nucleation and is one of the most common therapeutic agents used to prevent stone formation. Methods: Thirty long duration crewmembers (29 male, 1 female) participated in this study. 24-hour urines were collected and dietary monitoring was performed pre-, in-, and postflight. Crewmembers in the treatment group received two potassium citrate (KCIT) pills, 10 mEq/pill, ingested daily beginning 3 days before launch, all in-flight days and through 14 days postflight. Urinary biochemical and dietary analyses were completed. Results: KCIT treated subjects exhibited decreased urinary calcium excretion and maintained the levels of calcium oxalate supersaturation risk at their preflight levels. The increased urinary pH levels in these subjects reduced the risk of uric acid stones. Discussion: The current study investigated the use of potassium citrate as a countermeasure to minimize the risk of stone formation during ISS missions. Results suggest that supplementation with potassium citrate decreases the risk of stone formation during and immediately after spaceflight.

Accuracy of contacts calculated from 3D images of occlusal surfaces.

PubMed

DeLong, R; Knorr, S; Anderson, G C; Hodges, J; Pintado, M R

2007-06-01

Compare occlusal contacts calculated from 3D virtual models created from clinical records to contacts identified clinically using shimstock and transillumination. Upper and lower full arch alginate impressions and vinyl polysiloxane centric interocclusal records were made of 12 subjects. Stone casts made from the alginate impressions and the interocclusal records were optically scanned. Three-dimensional virtual models of the dental arches and interocclusal records were constructed using the Virtual Dental Patient Software. Contacts calculated from the virtual interocclusal records and from the aligned upper and lower virtual arch models were compared to those identified clinically using 0.01mm shimstock and transillumination of the interocclusal record. Virtual contacts and transillumination contacts were compared by anatomical region and by contacting tooth pairs to shimstock contacts. Because there is no accepted standard for identifying occlusal contacts, methods were compared in pairs with one labeled "standard" and the second labeled "test". Accuracy was defined as the number of contacts and non-contacts of the "test" that were in agreement with the "standard" divided by the total number of contacts and non-contacts of the "standard". Accuracy of occlusal contacts calculated from virtual interocclusal records and aligned virtual casts compared to transillumination were: 0.87+/-0.05 and 0.84+/-0.06 by region and 0.95+/-0.07 and 0.95+/-0.05 by tooth, respectively. Comparisons with shimstock were: 0.85+/-0.15 (record), 0.84+/-0.14 (casts), and 81+/-17 (transillumination). The virtual record, aligned virtual arches, and transillumination methods of identifying contacts are equivalent, and show better agreement with each other than with the shimstock method.

In situ ∼2.0 Ma trees discovered as fossil rooted stumps, lowermost Bed I, Olduvai Gorge, Tanzania.

PubMed

Habermann, Jörg M; Stanistreet, Ian G; Stollhofen, Harald; Albert, Rosa M; Bamford, Marion K; Pante, Michael C; Njau, Jackson K; Masao, Fidelis T

2016-01-01

The discovery of fossil rooted tree stumps in lowermost Lower Bed I from the western Olduvai Basin, Tanzania, age-bracketed by the Naabi Ignimbrite (2.038 ± 0.005 Ma) and Tuff IA (1.88 ± 0.05 Ma), provides the first direct, in situ, and to date oldest evidence of living trees at Olduvai Gorge. The tree relicts occur in an interval dominated by low-viscosity mass flow and braided fluvial sediments, deposited at the toe of a largely Ngorongoro Volcano-sourced volcaniclastic fan apron that comprised a widely spaced network of ephemeral braided streams draining northward into the Olduvai Basin. Preservation of the trees occurred through their engulfment by mass flows, post-mortem mold formation resulting from differential decay of woody tissues, and subsequent fluvially-related sediment infill, calcite precipitation, and cast formation. Rhizolith preservation was triggered by the interaction of root-induced organic and inorganic processes to form rhizocretionary calcareous root casts. Phytolith analyses were carried out to complete the paleoenvironmental reconstruction. They imply a pronounced seasonality and indicate a wooded landscape with grasses, shrubs, and sedges growing nearby, comparable to the low, open riverine woodland (unit 4c) along the Garusi River and tributaries in the Laetoli area. Among the tree stump cluster were found outsized lithic clasts and those consisting of quartzite were identified as Oldowan stone tool artifacts. In the context of hominin activity, the identification of wooded grassland in association with nearby freshwater drainages and Oldowan artifacts significantly extends our paleoenvironmental purview on the basal parts of Lower Bed I, and highlights the hitherto underrated role of the yet poorly explored western Olduvai Gorge area as a potential ecologically attractive setting and habitat for early hominins. Copyright © 2015 Elsevier Ltd. All rights reserved.

Project CAST.

ERIC Educational Resources Information Center

Charles County Board of Education, La Plata, MD. Office of Special Education.

The document outlines procedures for implementing Project CAST (Community and School Together), a community-based career education program for secondary special education students in Charles County, Maryland. Initial sections discuss the role of a learning coordinator, (including relevant travel reimbursement and mileage forms) and an overview of…

Fracture resistance of Ti-5Al-2.5Sn extra-low interstitial castings

NASA Technical Reports Server (NTRS)

Fiftal, C. F.; Bolstad, D. A.; Misra, M. S.

1978-01-01

Fracture toughness and cyclic crack propagation data for Ti-5Al-2.5Sn extra-low interstitial (ELI) castings, 0.51 and 2.54 cm (0.20 and 1.00 in.) thick, at 394, 294, 77, and 20 K (250, 70, -320, and -423 F), are presented. Both surface flaw and compact tension geometries were tested. Comparison is made with other titanium alloys in both wrought and cast forms. Crack propagation resistance is comparable to wrought Ti-5Al-2.5Sn ELI, even with the extremely coarse as-cast grain size encountered.

High Integrity Castings: Proceedings of the Conference on Advances in High Integrity Castings Held in Conjunction with the 1988 World Materials Congress, Chicago, Illinois, USA, 24-30 September 1988

DTIC Science & Technology

1988-01-01

above design requirements. The The first cast parts used in this higher strength standard chemistry parts application were of the Extra Low...present work was to study the use of beta THE HIGH COST OF TITANIUM alloys can limit their titanium alloys in the cast form. Beta or use to applications ...refractory as was is intended to achieve a pouring stream su- used with the nozzles for steel applications . perior to conventional nozzle designs , and this

Improved Slip Casting Of Ceramic Models

NASA Technical Reports Server (NTRS)

Buck, Gregory M.; Vasquez, Peter; Hicks, Lana P.

1994-01-01

Improved technique of investment slip casting developed for making precise ceramic wind-tunnel models. Needed in wind-tunnel experiments to verify predictions of aerothermodynamical computer codes. Ceramic materials used because of their low heat conductivities and ability to survive high temperatures. Present improved slip-casting technique enables casting of highly detailed models from aqueous or nonaqueous solutions. Wet shell molds peeled off models to ensure precise and undamaged details. Used at NASA Langley Research Center to form superconducting ceramic components from nonaqueous slip solutions. Technique has many more applications when ceramic materials developed further for such high-strength/ temperature components as engine parts.

Methods for Casting Subterranean Ant Nests

PubMed Central

Tschinkel, Walter R.

2010-01-01

The study of subterranean ant nests has been impeded by the difficulty of rendering their structures in visible form. Here, several different casting materials are shown to make perfect casts of the underground nests of ants. Each material (dental plaster, paraffin wax, aluminum, zinc) has advantages and limitations, which are discussed. Some of the materials allow the recovery of the ants entombed in the casts, allowing a census of the ants to be connected with features of their nest architecture. The necessary equipment and procedures are described in the hope that more researchers will study this very important aspect of ant natural history. PMID:20673073

Process for forming unusually strong joints between metals and ceramics by brazing at temperatures that do not exceed 750/sup 0/C

DOEpatents

Hammond, J.P.; David, S.A.; Woodhouse, J.J.

1984-12-04

This invention is a process for joining metals to ceramics to form very strong bonds using low brazing temperature, i.e., less than 750/sup 0/C, and particularly for joining nodular cast iron to partially stabilized zirconia. The process provides that the ceramic be coated with an active metal, such as titanium, that can form an intermetallic with a low melting point brazing alloy such as 60Ag-30Cu-10Sn. The nodular cast iron is coated with a noncarbon containing metal, such as copper, to prevent carbon in the nodular cast iron from dissolving in the brazing alloy. These coated surfaces can be brazed together with the brazing alloy between at less than 750/sup 0/C to form a very strong joint. An even stronger bond can be formed if a transition piece is used between the metal and ceramic. It is preferred for the transition piece to have a coefficient of thermal expansion compatible with the coefficient of thermal expansion of the ceramic, such as titanium.

Process for forming unusually strong joints between metals and ceramics by brazing at temperatures that do no exceed 750 degree C.

DOEpatents

Hammond, Joseph P.; David, Stan A.; Woodhouse, John J.

1986-01-01

This invention is a process for joining metals to ceramics to form very strong bonds using low brazing temperature, i.e., less than 750.degree. C., and particularly for joining nodular cast iron to partially stabilized zirconia. The process provides that the ceramic be coated with an active metal, such as titanium, that can form an intermetallic with a low melting point brazing alloy such as 60Ag-30Cu-10Sn. The nodular cast iron is coated with a noncarbon containing metal, such as copper, to prevent carbon in the nodular cast iron from dissolving in the brazing alloy. These coated surfaces can be brazed together with the brazing alloy between at less than 750.degree. C. to form a very strong joint. An even stronger bond can be formed if a transition piece is used between the metal and ceramic. It is preferred for the transition piece to have a coefficient of thermal compatible with the coefficient of thermal expansion of the ceramic, such as titanium.

Sealing properties of three luting agents used for complete cast crowns: a bacterial leakage study.

PubMed

Zmener, O; Pameijer, C H; Rincon, S M H; Serrano, S A; Chaves, C

2013-01-01

To assess the sealing properties of three different luting materials used for cementation of full cast crowns on extracted human premolars. Thirty noncarious human premolars were prepared in a standardized fashion for full cast crown restorations. All margins were placed in dentin. After impressions of the preparations, stone dies were fabricated on which copings were waxed, which were cast in type III alloy using standardized laboratory methods. Teeth were randomly assigned to three groups of 10 samples each (n=10), for which the following cements were used: 1) a resin-modified glass ionomer cement, Rely X Luting Plus (3M ESPE, St Paul, MN, USA); 2) a self-adhesive resin cement, Maxcem Elite (Kerr Corporation, Orange, CA, USA); and 3) a glass ionomer cement, Ketac Cem (3M ESPE), the latter used as control. After cementation the samples were allowed to bench-set for 10 minutes, stored in water at 37°C, subjected to thermal cycling (2000×, between 5°C and 55°C, dwell time 35 seconds), and then stored in sterile phosphate buffer for seven days at 37°C. Subsequently, the occlusal surface was carefully reduced until the dentin was exposed. Finishing on wet sand paper removed the gold flash caused by grinding. After sterilization, the specimens were subjected to bacterial microleakage in a dual chamber apparatus for 60 days. Bacterial leakage was checked daily. Data were analyzed using the Kaplan-Meier survival test. Significant pairwise differences were analyzed using the log-rank test followed by Fisher exact test at a p<0.05 level of significance. Rely X Luting Plus showed the lowest microleakage scores, which statistically differed significantly from Maxcem Elite and Ketac Cem (p<0.05). Rely X Luting Plus cement displayed significantly lower microleakage scores than a self-adhesive resin-based and conventional glass ionomer cement.

[Evaluating the accuracy of three-dimensional reconstruction of the intercuspal position for dentition casts aided by a mechanical appliance].

PubMed

Hu, Z W; Li, W W; Zhang, X Y; Fan, B L; Wang, Y; Sun, Y C

2016-08-01

To develop a aided mechanical appliance for rapid reconstruction of three-dimensional(3D)relationship of dentition model after scanning and evaluation of its accuracy. The appliance was designed by forward engineering software and fabricated by a high precision computer numerical control(CNC)system. It contained upper and lower body, magnetic pedestal and three pillars. Nine 3 mm diameter hemispheres were distributed equally on the axial surface of each pedestal. Faro Edge 1.8m was used to directly obtain center of each hemisphere(contact method), defined as known center. A pair of die-stone standard dentition model were fixed in intercuspal position and then fixed on the magnetic pedestals with low expansion ratio plaster. Activity 880 dental scanner was used to scan casts after the plaster was completely set. In Geomagic 2012, the centers of each hemisphere were fitted and defined as scanning centers. Scanning centers were aligned to known centers by reference point system to finish the 3D reconstruction of the intercuspal occlusion for the dentition casts. An observation coordinate system was interactively established. The straight-line distances in the X(coronal), Y(saggital), and Z(vertical)between the remaining 6 pairs of center points derived from contact method and fitting method were measured respectively and analyzed using a paired t-test. The differences of the straight-line distances of the remaining 6 pairs of center points between the two methods were X:(-0.05±0.10)mm, Y:(0.02±0.06)mm, and Z:(0.01 ± 0.05)mm. The results of paired t-test showed no significant differences(P>0.05). The mechanical appliance can help to reconstruct 3D jaw relation by scanning single upper and lower dentition model with usual commercial available dental cast scanning system.

Do "inhibitors of crystallisation" play any role in the prevention of kidney stones? A critique.

PubMed

Robertson, William G

2017-02-01

A critical examination of data in the literature and in as yet unpublished laboratory records on the possible role of so-called inhibitors of crystallisation in preventing the formation of calcium-containing kidney stones leads to the following conclusions. So-called inhibitors of spontaneous "self-nucleation" are unlikely to play any role in the initiation of the crystallisation of CaOx or CaP in urine because excessive urinary supersaturation of urine with respect to these salts dominates the onset of "self-nucleation" within the normal time frame of the transit of tubular fluid through the nephron (3-4 min). Inhibitors of the crystal growth of CaOx crystals may or may not play a significant role in the prevention of CaOx stone-formation since once again excessive supersaturation of urine can overwhelm any potential effect of the inhibitors on the growth process. However, they may play a role as inhibitors of crystal growth at lower levels of metastable supersaturation when the balance between supersaturation and inhibitors is more equal. Inhibitors of CaOx crystal aggregation may play a significant role in the prevention of stones, since they do not appear to be strongly affected by excessive supersaturation, either in vitro or in vivo. Inhibitors of CaOx crystal binding to renal tubular epithelium may exist but further studies are necessary to elucidate their importance in reducing the risk of initiating stones in the renal tubules. Inhibitors of CaOx crystal binding to Randall's Plaques and Randall's Plugs may exist but further studies are necessary to elucidate their importance in reducing the risk of initiating stones on renal papillae. There may be an alternative explanation other than a deficiency in the excretion of inhibitors for the observations that there is a difference between CaOx crystal size and degree of aggregation in the fresh, warm urines of normal subjects compared those in urine from patients with recurrent CaOx stones. This difference may depend more on the site of "self-nucleation" of CaOx crystals in the renal tubule rather than on a deficiency in the excretion of so-called inhibitors of crystallisation by patients with CaOx stones. The claim that administration of potassium citrate, potassium magnesium citrate or magnesium hydroxide reduces the rate of stone recurrence may be due to the effect of these forms of medication on the supersaturation of urine with respect to CaOx and CaP rather than to any increase in "inhibitory activity" attributed to these forms of treatment. In summary, there is a competition between supersaturation and so-called inhibitors of crystallisation which ultimately determines the pattern of crystalluria in stone-formers and normals. If the supersaturation of urine with respect to CaOx reaches or exceeds the 3-4 min formation product of that salt, then it dominates the crystallisation process both in terms of "self-nucleation" and crystal growth but appears to have little or no effect on the degree of aggregation of the crystals produced. At supersaturation levels of urine with respect to CaOx well below the 3-4 min formation product of that salt, the influence of inhibitors increases and some may affect not only the degree of aggregation but also the crystal growth of any pre-formed crystals of CaOx at these lower levels of metastability.

Formation and Characterization of Langmuir Silk Films

DTIC Science & Technology

1993-07-01

studied for phase transitions as immo- fibroin and sericin . Fibroin is the protein that forms the bilization matrices have been in the form of cast mem...properties. Sericins are a group membrane materials. However, the casting process has of gummy proteins which bind the fibroin filaments, limitations...approximately 5 mm X 5 mm pieces. The cocoon material was boiled in distilled water for 2 h with changes 7- of water to solubilize and remove the sericin

Catalyzed enzyme electrodes

DOEpatents

Zawodzinski, Thomas A.; Wilson, Mahlon S.; Rishpon, Judith; Gottesfeld, Shimshon

1993-01-01

An enzyme electrode is prepared with a composite coating on an electrical conductor. The composite coating is formed from a casting solution of a perfluorosulfonic acid polymer, an enzyme, and a carbon supported catalyst. The solution may be cast directly on the conductor surface or may be formed as a membrane and applied to the surface. The perfluorosulfonic acid ionomer formed from the casting solution provides an insoluble biocompatible protective matrix for the enzyme and acts to retain the enzyme for long term availability in the electrode structure. The carbon supported catalyst provides catalytic sites throughout the layer for the oxidation of hydrogen peroxide from the enzyme reactions. The carbon support then provides a conductive path for establishing an electrical signal to the electrical conductor. In one embodiment, the electrical conductor is a carbon cloth that permits oxygen or other gas to be introduced to the perfluorosulfonic polymer to promote the enzyme reaction independent of oxygen in the solution being tested.

Novel technologies for the lost foam casting process

NASA Astrophysics Data System (ADS)

Jiang, Wenming; Fan, Zitian

2018-03-01

Lost foam casting (LFC) is a green precision casting process categorized as a near net forming technology. Yet, despite its popularity, it still suffers from some technological problems, such as poor filling ability of the castings, coarse and non-dense microstructure, low mechanical properties for the Al and Mg LFC processes, and defective carburization for the low carbon steel LFC process. These drawbacks restrict the development and widespread application of the LFC process. To solve these problems, the present study developed several novel LFC technologies, namely, LFC technologies under vacuum and low pressure, vibration solidification, and pressure solidification conditions; expendable shell casting technology; and preparation technology of bimetallic castings based on the LFC process. The results showed that the LFC under vacuum and low pressure evidently improved the filling ability and solved the oxidization problem of the alloys, which is suitable for producing complex and thinwall castings. The vibration and pressure solidifications increased the compactness of the castings and refined the microstructure, significantly improving the mechanical properties of the castings. The expendable shell casting technology could solve the pore, carburization, and inclusion defects of the traditional LFC method, obtaining castings with acceptable surface quality. Moreover, the Al/Mg and Al/Al bimetallic castings with acceptable metallurgical bonding were successfully fabricated using the LFC process. These proposed novel LFC technologies can solve the current technological issues and promote the technological progress of the LFC process.

Dietary treatment of urinary risk factors for renal stone formation. A review of CLU Working Group.

PubMed

Prezioso, Domenico; Strazzullo, Pasquale; Lotti, Tullio; Bianchi, Giampaolo; Borghi, Loris; Caione, Paolo; Carini, Marco; Caudarella, Renata; Ferraro, Manuel; Gambaro, Giovanni; Gelosa, Marco; Guttilla, Andrea; Illiano, Ester; Martino, Marangella; Meschi, Tiziana; Messa, Piergiorgio; Miano, Roberto; Napodano, Giorgio; Nouvenne, Antonio; Rendina, Domenico; Rocco, Francesco; Rosa, Marco; Sanseverino, Roberto; Salerno, Annamaria; Spatafora, Sebastiano; Tasca, Andrea; Ticinesi, Andrea; Travaglini, Fabrizio; Trinchieri, Alberto; Vespasiani, Giuseppe; Zattoni, Filiberto

2015-07-07

Diet interventions may reduce the risk of urinary stone formation and its recurrence, but there is no conclusive consensus in the literature regarding the effectiveness of dietary interventions and recommendations about specific diets for patients with urinary calculi. The aim of this study was to review the studies reporting the effects of different dietary interventions for the modification of urinary risk factors in patients with urinary stone disease. A systematic search of the Pubmed database literature up to July 1, 2014 for studies on dietary treatment of urinary risk factors for urinary stone formation was conducted according to a methodology developed a priori. Studies were screened by titles and abstracts for eligibility. Data were extracted using a standardized form and the quality of evidence was assessed. Evidence from the selected studies were used to form evidence-based guideline statements. In the absence of sufficient evidence, additional statements were developed as expert opinions. General measures: Each patient with nephrolithiasis should undertake appropriate evaluation according to the knowledge of the calculus composition. Regardless of the underlying cause of the stone disease, a mainstay of conservative management is the forced increase in fluid intake to achieve a daily urine output of 2 liters. HYPERCALCIURIA: Dietary calcium restriction is not recommended for stone formers with nephrolithiasis. Diets with a calcium content ≥ 1 g/day (and low protein-low sodium) could be protective against the risk of stone formation in hypercalciuric stone forming adults. Moderate dietary salt restriction is useful in limiting urinary calcium excretion and thus may be helpful for primary and secondary prevention of nephrolithiasis. A low-normal protein intake decrease calciuria and could be useful in stone prevention and preservation of bone mass. Omega-3 fatty acids and bran of different origin decreases calciuria, but their impact on the urinary stone risk profile is uncertain. Sports beverage do not affect the urinary stone risk profile. HYPEROXALURIA: A diet low in oxalate and/or a calcium intake normal to high (800-1200 mg/day for adults) reduce the urinary excretion of oxalate, conversely a diet rich in oxalates and/or a diet low in calcium increase urinary oxalate. A restriction in protein intake may reduce the urinary excretion of oxalate although a vegetarian diet may lead to an increase in urinary oxalate. Adding bran to a diet low in oxalate cancels its effect of reducing urinary oxalate. Conversely, the addition of supplements of fruit and vegetables to a mixed diet does not involve an increased excretion of oxalate in the urine. The intake of pyridoxine reduces the excretion of oxalate. HYPERURICOSURIA: In patients with renal calcium stones the decrease of the urinary excretion of uric acid after restriction of dietary protein and purine is suggested although not clearly demonstrated. HYPOCITRATURIA: The administration of alkaline-citrates salts is recommended for the medical treatment of renal stone-formers with hypocitraturia, although compliance to this treatment is limited by gastrointestinal side effects and costs. Increased intake of fruit and vegetables (excluding those with high oxalate content) increases citrate excretion and involves a significant protection against the risk of stone formation. Citrus (lemons, oranges, grapefruit, and lime) and non citrus fruits (melon) are natural sources of dietary citrate, and several studies have shown the potential of these fruits and/or their juices in raising urine citrate levels. There are enought basis to advice an adequate fluid intake also in children. Moderate dietary salt restriction and implementation of potassium intake are useful in limiting urinary calcium excretion whereas dietary calcium restriction is not recommended for children with nephrolithiasis. It seems reasonable to advice a balanced consumption of fruit and vegetables and a low consumption of chocolate and cola according to general nutritional guidelines, although no studies have assessed in pediatric stone formers the effect of fruit and vegetables supplementation on urinary citrate and the effects of chocolate and cola restriction on urinary oxalate in pediatric stone formers. Despite the low level of scientific evidence, a low-protein (< 20 g/day) low-salt (< 2 g/day) diet with high hydration (> 3 liters/day) is strongly advised in children with cystinuria. ELDERLY: In older patients dietary counseling for renal stone prevention has to consider some particular aspects of aging. A restriction of sodium intake in association with a higher intake of potassium, magnesium and citrate is advisable in order to reduce urinary risk factors for stone formation but also to prevent the loss of bone mass and the incidence of hypertension, although more hemodynamic sensitivity to sodium intake and decreased renal function of the elderly have to be considered. A diet rich in calcium (1200 mg/day) is useful to maintain skeletal wellness and to prevent kidney stones although an higher supplementation could involve an increase of risk for both the formation of kidney stones and cardiovascular diseases. A lower content of animal protein in association to an higher intake of plant products decrease the acid load and the excretion of uric acid has no particular contraindications in the elderly patients, although overall nutritional status has to be preserved.

The chemical phenol extraction of intermetallic particles from casting AlSi5Cu1Mg alloy.

PubMed

Mrówka-Nowotnik, G; Sieniawski, J; Nowotnik, A

2010-03-01

This paper presents a chemical extraction technique for determination of intermetallic phases formed in the casting AlSi5Cu1Mg aluminium alloy. Commercial aluminium alloys contain a wide range of intermetallic particles that are formed during casting, homogenization and thermomechanical processing. During solidification, particles of intermetallics are dispersed in interdendritic spaces as fine primary phases. Coarse intermetallic compounds that are formed in this aluminium alloy are characterized by unique atomic arrangement (crystallographic structure), morphology, stability, physical and mechanical properties. The volume fraction, chemistry and morphology of the intermetallics significantly affect properties and material behaviour during thermomechanical processing. Therefore, accurate determination of intermetallics is essential to understand and control microstructural evolution in Al alloys. Thus, in this paper it is shown that chemical phenol extraction method can be applied for precise qualitative evaluation. The results of optical light microscopy LOM, scanning electron microscopy SEM and X-ray diffraction XRD analysis reveal that as-cast AlSi5Cu1Mg alloy contains a wide range of intermetallic phases such as Al(4)Fe, gamma- Al(3)FeSi, alpha-Al(8)Fe(2)Si, beta-Al(5)FeSi, Al(12)FeMnSi.

Method of forming components for a high-temperature secondary electrochemical cell

DOEpatents

Mrazek, F.C.; Battles, J.E.

1981-05-22

A method of forming a component for a high-temperature secondary electrochemical cell having a positive electrode including a sulfide selected from the group consisting of iron sulfides, nickel sulfides, copper sulfides and cobalt sulfides, a negative electrode including an alloy of aluminum and an electrically insulating porous separator between said electrodes is described. The improvement comprises forming a slurry of solid particles dispersed in a liquid electrolyte such as the lithium chloride-potassium chloride eutectic, casting the slurry into a form having the shape of one of the components and smoothing the exposed surface of the slurry, cooling the cast slurry to form the solid component, and removing same. Electrodes and separators can be thus formed.

The fragmented character of Middle Palaeolithic stone tool technology.

PubMed

Turq, Alain; Roebroeks, Wil; Bourguignon, Laurence; Faivre, Jean-Philippe

2013-11-01

The importance of the transport of stone artefacts in structuring Neandertal lithic assemblages has often been addressed, but the degree to which this led to fragmentation of lithic reduction over Middle Palaeolithic landscapes has not been explicitly studied thus far. Large-scale excavations of Middle Palaeolithic open-air sites and refitting studies of the retrieved assemblages have yielded new, high-resolution data on the mobile aspects of Neandertal stone tool technology. In this paper, we integrate lithic technology and raw material data from recent studies of Middle Palaeolithic open-air and rock shelter sites in Western Europe. We demonstrate that the results of a variety of typological, technological (especially refitting), and lithological studies have important consequences for our knowledge of the acquisition of raw materials and subsequent production, usage and discard of stone artefacts in the Middle Palaeolithic. Neandertal production and use of stone tools was fragmented in three domains: the spatial, the temporal and the social domain. We show that this versatile segmentation of stone artefact handling strategies is a main determinant of the character of the Neandertal archaeological record. Our data testify to ubiquitous and continuous transport of stone artefacts of a wide variety of forms, picked by Neandertals using selection criteria that were sometimes far removed from what archaeologists have traditionally considered, and to some degree still consider, to be desired end products of knapping activities. The data presented here testify to the variability and versatility of Middle Palaeolithic stone tool technology, whose fragmented character created very heterogeneous archaeological assemblages, usually the product of a wide variety of independent import, use, discard and/or subsequent transport events. Copyright © 2013 Elsevier Ltd. All rights reserved.

AIS/DOE Technology Roadmap Program: Strip Casting: Anticipating New Routes To Steel Sheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prof. Alan W. Camb; Prof. Anthony Rollett

2001-08-31

To determine the potential for strip casting in the steel industry and to develop the fundamental knowledge necessary to allow the role of strip casting in the modern steel industry to be understood. Based upon a study of carbon steel strip castings that were either produced for the program at British Steel or were received from a pre-commercial production machine, the following conclusions were made. Strip casting of carbon steels is technically feasible for sheet material from slightly less than 1 mm thick to 3 mm thick, and, assuming that it is economically viable, it will be first applied inmore » carbon steel markets that do not require stringent surface quality or extensive forming. The potential of strip casting as a casting process to be developed for steel castings is very high as the cast strip has some very novel characteristics. Direct cast carbon strip has better surface quality, shape and profile than any other casting process currently available. The more rapidly solidified structure of direct cast strip tends to be strong with low ductility; however, with adequate thermal treatment, it is possible to develop a variety of properties from the same grade. The process is more amenable at this time to production tonnages per year of the order of 500,000 tons and as such will first find niche type applications. This technology is an additional technology for steel production and will be in addition to, rather than a replacement for, current casting machines.« less

Structure and properties of stir-cast zinc alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

LeHuy, H.; Blain J.; Masounave, J.

Stir casting (or rheocasting) of ZA-27 zinc alloys was investigated experimentally. By vigorously agitating the alloys during cooling, the dendrites that were forming were fragmented giving a unique structure composed of spherical and rosette shaped particles suspended in the remaining liquid. Under high shear rates ({center dot}{gamma} = 300s{sup {minus}1} or more) the slurries with primary particle concentrations as high as 60% displayed viscosities as low as 20 poises and could easily be casted. The effects of processing variables such as shearing and cooling rates and casting temperatures were studied. Their relative importance on the rheological and microstructural behavior ofmore » the stir cast alloys are discussed. Results from viscosity measurements on slurries show that non-dendritical ZA-27 alloys obey a power law fluid model. Finally, results from mechanical and compressive studies carried out on solidified slurries are discussed and compared to conventional casted and wrought alloy properties.« less

In-situ conditioning of a strip casting roll

DOEpatents

Williams, Robert S.; Campbell, Steven L.

1997-01-01

A strip caster (10) for producing a continuous strip (24) has a tundish (12) for containing a melt (14) and a pair of horizontally disposed water cooled casting rolls (22). The casting rolls are juxtaposed relative to one another for forming a pouring basin (18) for receiving the melt through a teeming tube (16) thereby establishing a meniscus (20) between the rolls for forming a strip (24). The melt is protected from the outside air by a non-oxidizing gas passed through a supply line (28) to a sealing chamber (26). Devices (29) for conditioning the outer peripheral chill surfaces of the casting rolls includes grit blasting nozzles (30A, 30B, 30C, 30D), a collection trough (32) for gathering the grit, a line (34) for recycling the grit to a bag house (36), a feeder (38) and a pressurized distributor (40) for delivering the grit to the nozzles. The conditioning nozzles remove dirt, metal oxides and surface imperfections providing a clean surface readily wetted by the melt.

In-situ conditioning of a strip casting roll

DOEpatents

Williams, R.S.; Campbell, S.L.

1997-07-29

A strip caster (10) for producing a continuous strip (24) has a tundish (12) for containing a melt (14) and a pair of horizontally disposed water cooled casting rolls (22). The casting rolls are juxtaposed relative to one another for forming a pouring basin (18) for receiving the melt through a teeming tube (16) thereby establishing a meniscus (20) between the rolls for forming a strip (24). The melt is protected from the outside air by a non-oxidizing gas passed through a supply line (28) to a sealing chamber (26). Devices (29) for conditioning the outer peripheral chill surfaces of the casting rolls includes grit blasting nozzles (30A, 30B, 30C, 30D), a collection trough (32) for gathering the grit, a line (34) for recycling the grit to a bag house (36), a feeder (38) and a pressurized distributor (40) for delivering the grit to the nozzles. The conditioning nozzles remove dirt, metal oxides and surface imperfections providing a clean surface readily wetted by the melt.

Method for uniformly distributing carbon flakes in a positive electrode, the electrode made thereby and compositions

DOEpatents

Mrazek, Franklin C.; Smaga, John A.; Battles, James E.

1983-01-01

A positive electrode for a secondary electrochemical cell wherein an electrically conductive current collector is in electrical contact with a particulate mixture of gray cast iron and an alkali metal sulfide and an electrolyte including alkali metal halides or alkaline earth metal halides. Also present may be a transition metal sulfide and graphite flakes from the conversion of gray cast iron to iron sulfide. Also disclosed is a method of distributing carbon flakes in a cell wherein there is formed an electrochemical cell of a positive electrode structure of the type described and a suitable electrolyte and a second electrode containing a material capable of alloying with alkali metal ions. The cell is connected to a source of electrical potential to electrochemically convert gray cast iron to an iron sulfide and uniformly to distribute carbon flakes formerly in the gray cast iron throughout the positive electrode while forming an alkali metal alloy in the negative electrode. Also disclosed are compositions useful in preparing positive electrodes.

Single-step fabrication of quantum funnels via centrifugal colloidal casting of nanoparticle films

PubMed Central

Kim, Jin Young; Adinolfi, Valerio; Sutherland, Brandon R.; Voznyy, Oleksandr; Kwon, S. Joon; Kim, Tae Wu; Kim, Jeongho; Ihee, Hyotcherl; Kemp, Kyle; Adachi, Michael; Yuan, Mingjian; Kramer, Illan; Zhitomirsky, David; Hoogland, Sjoerd; Sargent, Edward H.

2015-01-01

Centrifugal casting of composites and ceramics has been widely employed to improve the mechanical and thermal properties of functional materials. This powerful method has yet to be deployed in the context of nanoparticles—yet size–effect tuning of quantum dots is among their most distinctive and application-relevant features. Here we report the first gradient nanoparticle films to be constructed in a single step. By creating a stable colloid of nanoparticles that are capped with electronic-conduction-compatible ligands we were able to leverage centrifugal casting for thin-films devices. This new method, termed centrifugal colloidal casting, is demonstrated to form films in a bandgap-ordered manner with efficient carrier funnelling towards the lowest energy layer. We constructed the first quantum-gradient photodiode to be formed in a single deposition step and, as a result of the gradient-enhanced electric field, experimentally measured the highest normalized detectivity of any colloidal quantum dot photodetector. PMID:26165185

Heat Transfer Coefficient at Cast-Mold Interface During Centrifugal Casting: Calculation of Air Gap

NASA Astrophysics Data System (ADS)

Bohacek, Jan; Kharicha, Abdellah; Ludwig, Andreas; Wu, Menghuai; Karimi-Sibaki, Ebrahim

2018-06-01

During centrifugal casting, the thermal resistance at the cast-mold interface represents a main blockage mechanism for heat transfer. In addition to the refractory coating, an air gap begins to form due to the shrinkage of the casting and the mold expansion, under the continuous influence of strong centrifugal forces. Here, the heat transfer coefficient at the cast-mold interface h has been determined from calculations of the air gap thickness d a based on a plane stress model taking into account thermoelastic stresses, centrifugal forces, plastic deformations, and a temperature-dependent Young's modulus. The numerical approach proposed here is rather novel and tries to offer an alternative to the empirical formulas usually used in numerical simulations for a description of a time-dependent heat transfer coefficient h. Several numerical tests were performed for different coating thicknesses d C, rotation rates Ω, and temperatures of solidus T sol. Results demonstrated that the scenario at the interface is unique for each set of parameters, hindering the possibility of employing empirical formulas without a preceding experiment being performed. Initial values of h are simply equivalent to the ratio of the coating thermal conductivity and its thickness ( 1000 Wm-2 K-1). Later, when the air gap is formed, h drops exponentially to values at least one order of magnitude smaller ( 100 Wm-2 K-1).

Turbine vane structure

DOEpatents

Irwin, John A.

1980-08-19

A liquid cooled stator blade assembly for a gas turbine engine includes an outer shroud having a pair of liquid inlets and a pair of liquid outlets supplied through a header and wherein means including tubes support the header radially outwardly of the shroud and also couple the header with the pair of liquid inlets and outlets. A pair of turbine vanes extend radially between the shroud and a vane platform to define a gas turbine motive fluid passage therebetween; and each of the vanes is cooled by an internal body casting of super alloy material with a grooved layer of highly heat conductive material that includes spaced apart flat surface trailing edges in alignment with a flat trailing edge of the casting joined to wall segments of the liner which are juxtaposed with respect to the internal casting to form an array of parallel liquid inlet passages on one side of the vane and a second plurality of parallel liquid return passages on the opposite side of the vane; and a superalloy heat and wear resistant imperforate skin covers the outer surface of the composite blade including the internal casting and the heat conductive layer; a separate trailing edge section includes an internal casting and an outer skin butt connected to the end surfaces of the internal casting and the heat conductive layer to form an easily assembled liquid cooled trailing edge section in the turbine vane.

Medical therapy, calcium oxalate urolithiasis

NASA Technical Reports Server (NTRS)

Ruml, L. A.; Pearle, M. S.; Pak, C. Y.

1997-01-01

The development of diagnostic protocols that identify specific risk factors for calcium oxalate nephrolithiasis has led to the formulation of directed medical regimens that are aimed at correcting the underlying metabolic disturbances. Initiation of these treatment programs has reduced markedly the rate of stone formation in the majority of patients who form stones. This article discusses the rationale that underlies the choice of medical therapy for the various pathophysiologic causes of calcium oxalate nephrolithiasis and the appropriate use of available medications.

Oxalate induces mitochondrial dysfunction and disrupts redox homeostasis in a human monocyte derived cell line.

PubMed

Patel, Mikita; Yarlagadda, Vidhush; Adedoyin, Oreoluwa; Saini, Vikram; Assimos, Dean G; Holmes, Ross P; Mitchell, Tanecia

2018-05-01

Monocytes/macrophages are thought to be recruited to the renal interstitium during calcium oxalate (CaOx) kidney stone disease for crystal clearance. Mitochondria play an important role in monocyte function during the immune response. We recently determined that monocytes in patients with CaOx kidney stones have decreased mitochondrial function compared to healthy subjects. The objective of this study was to determine whether oxalate, a major constituent found in CaOx kidney stones, alters cell viability, mitochondrial function, and redox homeostasis in THP-1 cells, a human derived monocyte cell line. THP-1 cells were treated with varying concentrations of CaOx crystals (insoluble form) or sodium oxalate (NaOx; soluble form) for 24h. In addition, the effect of calcium phosphate (CaP) and cystine crystals was tested. CaOx crystals decreased cell viability and induced mitochondrial dysfunction and redox imbalance in THP-1 cells compared to control cells. However, NaOx only caused mitochondrial damage and redox imbalance in THP-1 cells. In contrast, both CaP and cystine crystals did not affect THP-1 cells. Separate experiments showed that elevated oxalate also induced mitochondrial dysfunction in primary monocytes from healthy subjects. These findings suggest that oxalate may play an important role in monocyte mitochondrial dysfunction in CaOx kidney stone disease. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

A Miniaturized, 1.9F Integrated Optical Fiber and Stone Basket for Use in Thulium Fiber Laser Lithotripsy.

PubMed

Wilson, Christopher R; Hutchens, Thomas C; Hardy, Luke A; Irby, Pierce B; Fried, Nathaniel M

2015-10-01

The thulium fiber laser (TFL) is being explored as an alternative laser lithotripter to the standard holmium:yttrium-aluminum-garnet laser. The more uniform beam profile of the TFL enables higher power transmission through smaller fibers. In this study, a 100-μm core, 140-μm outer-diameter (OD) silica fiber with 5-mm length hollow steel tip was integrated with 1.3F (0.433-mm OD) nitinol wire basket to form a 1.9F (0.633-mm OD) device. TFL energy of 30 mJ, 500 μs pulse duration, and 500 Hz pulse rate was delivered to human uric acid stones, ex vivo. Stone ablation rates measured 1.5 ± 0.2 mg/s, comparable to 1.7 ± 0.3 mg/s using bare fiber tips separately with stone basket. With further development, this device may minimize stone retropulsion, allowing more efficient TFL lithotripsy at higher pulse rates. It may also provide increased flexibility, higher saline irrigation rates through the ureteroscope working channel, reduce fiber degradation compared with separate fiber and basket manipulation, and reduce laser-induced nitinol wire damage.

Condition assessment of a highly porous limestone fortress: damage categories and structural integrity

NASA Astrophysics Data System (ADS)

Török, Ákos; Czinder, Balázs; Farkas, Orsolya; Görög, Péter; Kopecskó, Katalin; Lógó, János; Rozgonyi-Boissinot, Nikoletta; Vásárhelyi, Balázs

2016-04-01

An emblematic monument the Citadella fortress of Budapest has been studied in details to assess the condition of stone structure. The fortress is a large stone structure of 220 m in length and 60 m in width. The height of the porous limestone walls are in between 12-16 metres. The fortress was completed in 1854 but has been partly rebuilt due to changes in function and war related structural damages. The present paper provides an overview of the lithology, weathering forms and structural condition of the fortress related to a forthcoming restoration-reconstruction project. To assess the condition of stone both on site and laboratory analyses were performed. Lithological varieties were documented. Major identified lithotypes are porous oolitic limestone, less porous bioclastic limestone and fine grained highly porous limestone. To identify wet zones portable moisture meter was applied. Surface strength and weathering grade were also assessed using Schmidt hammer and Duroscop. Decay features were diagnosed and mapped. The most common forms are white weathering crusts, scaling and blistering of crusts as well as granular disintegration. Black weathering crusts were also recognized. Laboratory tests were focused on mechanical properties of stones and on mineralogical and chemical compositional analyses. Small samples of stone were collected and tested by optical microscopy, SEM-EDX, XRD and Thermogravimetric analyses. Laboratory analyses proved that the major salt responsible for the damage of external walls is gypsum, although significant amount of halite and hygroscopic salts were found both on the external walls and in the interior parts of the fortress. During structural analyses displacement of walls, tilting and major amount of cracks were recognized. Loss of material and subsidence also caused problems and at some places unstable wall sections were recognized.

An audit of complications of fiberglass cast and hybrid cast for fractures of the foot, ankle and forearm in a Swedish emergency department.

PubMed

Ekwall, Anna; Carlberg, Eva; Palmberg, Gunilla; Sloberg, Rut

2018-06-01

Patients of all ages present to the Emergency Department (ED) with fractures that require immobilization using a cast. Various casting materials are used, all with advantages and disadvantages and there are considerable risks associated with fracture management using cast immobilization. The frequency and severity of complications from fiberglass or hybrid casts applied in the emergency setting has not previously been studied. The aim of this audit was to describe all the complications that occurred within 30 days in patients who had a fiberglass cast applied for immobilization of uncomplicated, non-angulated fractures of the foot, ankle or forearm. A retrospective care record audit was conducted that included 430 patients. The most common complications found were skin complications and cast related problems. No severe complications (e.g. compartment syndrome, venous thromboembolism or infection) were found. Fiberglass casts did not cause severe complications in this group of patients with uncomplicated fractures of the extremities. However, 25% of the patients experienced some form of complication. Interventions are needed that minimize the frequency of complications. As with all healthcare interventions, it is crucial that staff applying casts and providing follow-up care are competent. If casts are applied correctly and the patient is well informed and concordant, complications can be avoided. Copyright © 2018 Elsevier Ltd. All rights reserved.

Large structural, thin-wall castings made of metals subject to hot tearing, and their fabrication

NASA Technical Reports Server (NTRS)

Smashey, Russell W. (Inventor)

2001-01-01

An article, such as a gas turbine engine mixer, is made by providing a mold structure defining a thin-walled, hollow article, and a base metal that is subject to hot tear cracking when cast in a generally equiaxed polycrystalline form, such as Rene' 108 and Mar-M247. The article is fabricated by introducing the molten base metal into the mold structure, and directionally solidifying the base metal in the mold structure to form a directionally oriented structure. The directionally oriented structure may be formed of a single grain or oriented multiple grains.

Dynamical Mechanism of Scaling Behaviors in Multifractal Structure

NASA Astrophysics Data System (ADS)

Kim, Kyungsik; Jung, Jae Won; Kim, Soo Yong

2010-03-01

The pattern of stone distribution in the game of Go (Baduk, Weiqi, or Igo) can be treated in the mathematical and physical languages of multifractals. The concepts of fractals and multifractals have relevance to many fields of science and even arts. A significant and fascinating feature of this approach is that it provides a proper interpretation for the pattern of the two-colored (black and white) stones in terms of the numerical values of the generalized dimension and the scaling exponent. For our case, these statistical quantities can be estimated numerically from the black, white, and mixed stones, assuming the excluded edge effect that the cell form of the Go game has the self-similar structure. The result from the multifractal structure allows us to find a definite and reliable fractal dimension, and it precisely verifies that the fractal dimension becomes larger, as the cell of grids increases. We also find the strength of multifractal structures from the difference in the scaling exponents in the black, white, and mixed stones.

The increased risk of urinary stone disease in betel quid chewers.

PubMed

Allen, Siân E; Singh, Sadmeet; Robertson, William G

2006-08-01

The chewing of betel quid is a common practice in many countries of the world, particularly in Southeast Asia. The quid consists of a preparation of areca nut, betel leaf and calcium hydroxide "lime" paste ("chuna"). For the first time, we present a study that links its use to urinary stone disease. Eight patients (seven male and one female) who presented to our Stone Unit with recurrent urinary stones were included in the study. All were from the Indian subcontinent and were found to regularly chew betel. The patients underwent metabolic screening including blood, random urine and 24-h urine tests, quantitative chemical analysis of their calculi (where possible) and each completed a 7-day Diet Diary on his/her free, home diet. The study demonstrated a high incidence of hypercalciuria, a tendency to pass an alkaline urine and low urinary citrate excretion among the patients. Together these urinary risk factors increase the probability of developing both calcium phosphate-containing and calcium oxalate-containing stones. In support of this hypothesis, the patients were found to form stones consisting mainly of calcium phosphate but mixed with calcium oxalate. It is concluded that the use of calcium hydroxide "chuna" in the betel quid is the major contributor to the cause of urinary stones in its users. Moreover, the development of urinary lithiasis in such patients may be a precursor to milk-alkali syndrome in those individuals whose chewing habit is more extensive than in the patients in this study and who do not seek to decrease their habit over the long term.

Is oxidative stress, a link between nephrolithiasis and obesity, hypertension, diabetes, chronic kidney disease, metabolic syndrome?

PubMed Central

2017-01-01

Epidemiological studies have provided the evidence for association between nephrolithiasis and a number of cardiovascular diseases including hypertension, diabetes, chronic kidney disease, metabolic syndrome. Many of the co-morbidities may not only lead to stone disease but also be triggered by it. Nephrolithiasis is a risk factor for development of hypertension and have higher prevalence of diabetes mellitus and some hypertensive and diabetic patients are at greater risk for stone formation. An analysis of the association between stone disease and other simultaneously appearing disorders, as well as factors involved in their pathogenesis, may provide an insight into stone formation and improved therapies for stone recurrence and prevention. It is our hypothesis that association between stone formation and development of co-morbidities is a result of certain common pathological features. Review of the recent literature indicates that production of reactive oxygen species (ROS) and development of oxidative stress (OS) may be such a common pathway. OS is a common feature of all cardiovascular diseases (CVD) including hypertension, diabetes mellitus, atherosclerosis and myocardial infarct. There is increasing evidence that ROS are also produced during idiopathic calcium oxalate (CaOx) nephrolithiasis. Both tissue culture and animal model studies demonstrate that ROS are produced during interaction between CaOx/calcium phosphate (CaP) crystals and renal epithelial cells. Clinical studies have also provided evidence for the development of oxidative stress in the kidneys of stone forming patients. Renal disorders which lead to OS appear to be a continuum. Stress produced by one disorder may trigger the other under the right circumstances. PMID:22213019

Is oxidative stress, a link between nephrolithiasis and obesity, hypertension, diabetes, chronic kidney disease, metabolic syndrome?

PubMed

Khan, Saeed R

2012-04-01

Epidemiological studies have provided the evidence for association between nephrolithiasis and a number of cardiovascular diseases including hypertension, diabetes, chronic kidney disease, metabolic syndrome. Many of the co-morbidities may not only lead to stone disease but also be triggered by it. Nephrolithiasis is a risk factor for development of hypertension and have higher prevalence of diabetes mellitus and some hypertensive and diabetic patients are at greater risk for stone formation. An analysis of the association between stone disease and other simultaneously appearing disorders, as well as factors involved in their pathogenesis, may provide an insight into stone formation and improved therapies for stone recurrence and prevention. It is our hypothesis that association between stone formation and development of co-morbidities is a result of certain common pathological features. Review of the recent literature indicates that production of reactive oxygen species (ROS) and development of oxidative stress (OS) may be such a common pathway. OS is a common feature of all cardiovascular diseases (CVD) including hypertension, diabetes mellitus, atherosclerosis and myocardial infarct. There is increasing evidence that ROS are also produced during idiopathic calcium oxalate (CaOx) nephrolithiasis. Both tissue culture and animal model studies demonstrate that ROS are produced during interaction between CaOx/calcium phosphate (CaP) crystals and renal epithelial cells. Clinical studies have also provided evidence for the development of oxidative stress in the kidneys of stone forming patients. Renal disorders which lead to OS appear to be a continuum. Stress produced by one disorder may trigger the other under the right circumstances.

Anatomy of the collecting system of lower pole of the kidney in patients with a single renal stone: a comparative study with individuals with normal kidneys.

PubMed

Zomorrodi, Afshar; Buhluli, Abulfazel; Fathi, Samad

2010-07-01

At least 5% of women and 12% of men during their lives will experience renal colic, at least once. Many theories have been suggested for the etiology of renal stones and variations in the anatomy of the collecting system have been suggested to have a role in stone formation. This study was conducted to examine the role of variation of lower pole collecting system in patients with lower pole kidney stone and compared the same in normal persons (kidney donors). Investigation for the anatomy of the lower pole of the kidney (angle between lower infundibulum and pelvis, length and diameter of the infundibulum and number and pattern distribution of calyces) was carried out using intravenous pyelogram (IVP) in 100 cases with urinary stone (study cases) and 400 persons with normal kidneys (control subjects). The study was a retrospective cross-sectional case control study. Results were analyzed by Mann-Whitney and independent sample chi square tests. The mean infundibulum-pelvic angle (IPA) in control subjects and in patients was 112.5 +/- 10.7 and 96.6 +/- 28.8, respectively. There was significant correlation between reduced angle and stone formation (P= < 0.001). The mean infundibulum-uretero-pelvic angle (IUPA) in control subjects and study cases was 53.5 +/- 12.7 and 42.6 +/- 13.4, respectively. There was significant correlation between decreased angle and stone formation (P = or < 0.001). The mean length of infundibulum of lower pole of kidney (IPIL) in controls and study patients was 22.5 +/- 4.1 and 27.5 +/- 7.7, respectively, which was statistically significant (P< 0.001). The mean number of calyces in lower pole of the kidney (LPCN) in controls and study patients was 2.6 +/- 0.6 and 3 +/- 0.9, respectively, which was statistically significant (P = or < 0.002). There was no significant correlation between distribution of calyces and stone formation (P= 0.366). Our study suggests that abnormal renal anatomy was more common in patients with lower pole kidney stone and should be considered a risk factor for forming lower pole kidney stone.

System and process for the abatement of casting pollution, reclaiming resin bonded sand, and/or recovering a low BTU fuel from castings

DOEpatents

Scheffer, Karl D.

1984-07-03

Air is caused to flow through the resin bonded mold to aid combustion of the resin binder to form a low BTU gas fuel. Casting heat is recovered for use in a waste heat boiler or other heat abstraction equipment. Foundry air pollution is reduced, the burned portion of the molding sand is recovered for immediate reuse and savings in fuel and other energy is achieved.

System and process for the abatement of casting pollution, reclaiming resin bonded sand, and/or recovering a low Btu fuel from castings

DOEpatents

Scheffer, K.D.

1984-07-03

Air is caused to flow through the resin bonded mold to aid combustion of the resin binder to form a low Btu gas fuel. Casting heat is recovered for use in a waste heat boiler or other heat abstraction equipment. Foundry air pollutis reduced, the burned portion of the molding sand is recovered for immediate reuse and savings in fuel and other energy is achieved. 5 figs.

Inboard seal mounting

DOEpatents

Hayes, John R.

1983-01-01

A regenerator assembly for a gas turbine engine has a hot side seal assembly formed in part by a cast metal engine block having a seal recess formed therein that is configured to supportingly receive ceramic support blocks including an inboard face thereon having a regenerator seal face bonded thereto. A pressurized leaf seal is interposed between the ceramic support block and the cast metal engine block to bias the seal wear face into sealing engagement with a hot side surface of a rotary regenerator matrix.

The Urologist's Guide to the Galaxy

NASA Astrophysics Data System (ADS)

Moran, Michael E.

2007-04-01

``Far out in the uncharted backwaters of the unfashionable end of the Western Spiral arm of the Galaxy....'' Stone disease has affected mankind since earliest recorded history and will trouble us as we strive for the stars. Zero and microgravity are risk factors for urolithiasis, but the incidence is not yet known. Yet, the possible ``century of space exploration'' lies before us if payloads can be inexpensively offloaded from Earth's surface to orbit. The scientific publications about medical conditions of astronauts, deep water environments (submarine) and extreme conditions (Arctic and Antarctic) were reviewed to better understand the urologic risks. Actual events were next sought and any scientific data regarding therapeutic intent was carefully scrutinized. Incidence and risk potential could then be calculated and potential for intervention would then be known. The National Space Biomedical Research Institute has classified space health hazards and stone disease as ``Risk 12.'' Combined statistics from NASA's Gemini, Apollo, and Space Shuttle flights and long-term missions such as Shuttle-Mir or Skylab fail to reveal any ``disclosed'' emergency stone events. One published article suggests that some cosmonauts have in fact formed stones during space missions. Detailed data from 79 U.S. space missions, involving 219 person-flights, and 175 astronauts show 23 genitourinary problems (1.2 % or 0.07 incidence for 7 days). Submarine encounters are different, however, with 1.8 to 2.6 actual emergency evacuations per 1,000 person months and 23 kidney stone events (data from all subs in U.S. Atlantic Fleet 1993-1996). Extreme environment data appears more similar to that of spaceflight (despite full Earth's gravity) with 1,967 person-years distribution showing no definite stone formation/evacuation (but 335 or 3.6% were not-specified). Pak and co-workers at the University of Texas, Southwestern have extensively evaluated the metabolic consequences of bone-mineral loss and urinary parameters associated with the increased risk of stone formation in space. Astronauts are at significantly greater risk of forming calcium oxalate, calcium phosphate and uric acid stones, and this persists for a period of time following return to normal gravity. Conflicting data exists regarding submarine and extreme environmental databases as to the ``actual'' space mission risks but the hazard is real. Attempts to evaluate both diagnostic and therapeutic interventions are being pursued. As the number of space visitors increases, so should the incidence of urolithiasis. Both diagnostic and therapeutic methods need to be developed coincident to our further efforts in space.

Balloon Sculpture

ERIC Educational Resources Information Center

Warwick, James F.

1976-01-01

For the adventurous teacher and student there is an alternative to the often messy mixing, pouring, casting, cutting, scoring and sanding of plaster of Paris for casting or sculptural projects. Balloon sculpture, devised, designed and shown here by a sculptor/teacher, is an eye appealing sculptural form and holds a strong interest for students.…

The effect of different screw-tightening techniques on the stress generated on an internal-connection implant superstructure.

PubMed

Choi, Jung-Han; Lim, Young-Jun; Kim, Chang-Whe; Kim, Myung-Joo

2009-01-01

This study evaluated the effect of different screw-tightening sequences, forces, and methods on the stresses generated on a well-fitting internal-connection implant (Astra Tech) superstructure. A metal framework directly connected to four parallel implants was fabricated on a fully edentulous mandibular resin model. Six stone casts with four implant replicas were made from a pickup impression of the superstructure to represent a "well-fitting" situation. Stresses generated by four screw-tightening sequences (1-2-3-4, 4-3-2-1, 2-4-3-1, and 2-3-1-4), two forces (10 and 20 Ncm), and two methods (one-step and two-step) were evaluated. In the two-step method, screws were tightened to the initial torque (10 Ncm) in a predetermined screw-tightening sequence and then to the final torque (20 Ncm) in the same sequence. Stresses were recorded twice by three strain gauges attached to the framework (superior face midway between abutments). Deformation data were analyzed using multiple analysis of variance at a .05 level of statistical significance. In all stone casts, stresses were produced by the superstructure connection, regardless of screw-tightening sequence, force, and method. No statistically significant differences for superstructure preload stresses were found based on screw-tightening sequences (-180.0 to -181.6 microm/m) or forces (-163.4 and -169.2 microm/m) (P > .05). However, different screw-tightening methods induced different stresses on the superstructure. The two-step screw-tightening method (-180.1 microm/m) produced significantly higher stress than the one-step method (-169.2 microm/m) (P = .0457). Within the limitations of this in vitro study, screw-tightening sequence and force were not critical factors in the stress generated on a well-fitting internal-connection implant superstructure. The stress caused by the two-step method was greater than that produced using the one-step method. Further studies are needed to evaluate the effect of screw-tightening techniques on preload stress in various different clinical situations.

Hungarian travertine: a historic and current stone resource of Central Europe

NASA Astrophysics Data System (ADS)

Török, Ákos

2013-04-01

Travertine is a widespread dimension stone that was used worldwide in monuments. The best known examples are known from the Roman Empire from Italy, where this porous stone belonged to one of the favourite stone types. Ancient quarries of Tivoli provided material to major construction works to Rome. Other occurrences belonging to the Roman Empire outside of Rome were also used by the Romans. Some of the most important European deposits are known from Hungary. Exploitable travertine layers are found at many places in Hungary but at least two major areas were actively quarried by the Romans. One major deposit was not far away from the provincial capital of Roman Pannonia - called Aquincum, which currently forms a part of Budapest, while the other even larger occurrence is at Süttő, at the riverside of Danube some 50 km NE from the past capital. River Danube provided an excellent pathway of transport ting stone to the capital. Evidences indicate that quarrying activity in Süttő area has already begun during the 1st century BC and the travertine has been exploited with some interruptions since then. The present day quarries form the parts of the largest active dimension quarry system of Hungary. The exposed very thick banks (3 to 4m) of travertine were deposited from lukewarm springs during the Pleistocene period. Various types of travertine were used for constructing Roman aqueducts, fortresses, amphitheatre until the 4th century AD and were also transported to other parts of that Roman Province which extended to the present territory of Hungary, Austria, Slovenia and Croatia. Although the use of travertine has significantly decreased after the fall of Roman Empire in Central Europe and in Hungary, the presence of this stone was also documented from numerous Gothic and Baroque buildings from the area. The use of this stone became more popular again in the Carpathian Basin, when major constructions of larger cities such as Bratislava, Vienna or Budapest accelerated in the Austro-Hungarian Monarchy at the second part of the 19th century. The paper also provides information on various lithotypes of travertine and it also presents data on the physical properties and examples of its use in the monuments located in the cities of Central Europe.

Accuracy of implant impressions without impression copings: a three-dimensional analysis.

PubMed

Kwon, Joo-Hyun; Son, Yong-Ha; Han, Chong-Hyun; Kim, Sunjai

2011-06-01

Implant impressions without impression copings can be used for cement-retained implant restorations. A comparison of the accuracy of implant impressions with and without impression copings is needed. The purpose of this study was to evaluate and compare the dimensional accuracy of implant definitive casts that are fabricated by implant impressions with and without impression copings. An acrylic resin maxillary model was fabricated, and 3 implant replicas were secured in the right second premolar, first, and second molars. Two impression techniques were used to fabricate definitive casts (n=10). For the coping group (Group C), open tray impression copings were used for the final impressions. For the no-coping group (Group NC), cementable abutments were connected to the implant replicas, and final impressions were made assuming the abutments were prepared teeth. Computerized calculation of the centroids and long axes of the implant or stone abutment replicas was performed. The Mann-Whitney U test analyzed the amount of linear and rotational distortion between groups (α =.05). At the first molar site, Group NC showed significantly greater linear distortion along the Y-axis, with a small difference between the groups (Group C, 7.8 ± 7.4 μm; Group NC, 19.5 ± 12.2). At the second molar site, increased distortion was noted in Group NC for every linear and rotational variable, except for linear distortion along the Z-axis. Implant impression with open tray impression copings produced more accurate definitive casts than those fabricated without impression copings, especially those with greater inter-abutment distance. Copyright © 2011 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Tongue prints in biometric authentication: A pilot study

PubMed Central

Jeddy, Nadeem; Radhika, T; Nithya, S

2017-01-01

Background and Objectives: Biometric authentication is an important process for the identification and verification of individuals for security purposes. There are many biometric systems that are currently in use and also being researched. Tongue print is a new biometric authentication tool that is unique and cannot be easily forged because no two tongue prints are similar. The present study aims to evaluate the common morphological features of the tongue and its variations in males and females. The usefulness of alginate impression and dental cast in obtaining the lingual impression was also evaluated. Materials and Methods: The study sample included twenty participants. The participants were subjected to visual examination following which digital photographs of the dorsal surface of the tongue were taken. Alginate impressions of the tongue were made, and casts were prepared using dental stone. The photographs and the casts were analyzed by two observers separately for the surface morphology including shape, presence or absence of fissures and its pattern of distribution. Three reference points were considered to determine the shape of the tongue. Results: The most common morphological feature on the dorsum of the tongue was the presence of central fissures. Multiple vertical fissures were observed in males whereas single vertical fissure was a common finding in females. The fissures were predominantly shallow in males and deep in females. The tongue was predominantly U shaped in males and females. V-shaped tongue was observed in 25% of females. Conclusion: Tongue prints are useful in biometric authentication. The methodology used in the study is simple, easy and can be adopted by dentists on a regular basis. However, large-scale studies are required to validate the results and also identify other features of the tongue that can be used in forensics and biometric authentication process. PMID:28479712

Tongue prints in biometric authentication: A pilot study.

PubMed

Jeddy, Nadeem; Radhika, T; Nithya, S

2017-01-01

Biometric authentication is an important process for the identification and verification of individuals for security purposes. There are many biometric systems that are currently in use and also being researched. Tongue print is a new biometric authentication tool that is unique and cannot be easily forged because no two tongue prints are similar. The present study aims to evaluate the common morphological features of the tongue and its variations in males and females. The usefulness of alginate impression and dental cast in obtaining the lingual impression was also evaluated. The study sample included twenty participants. The participants were subjected to visual examination following which digital photographs of the dorsal surface of the tongue were taken. Alginate impressions of the tongue were made, and casts were prepared using dental stone. The photographs and the casts were analyzed by two observers separately for the surface morphology including shape, presence or absence of fissures and its pattern of distribution. Three reference points were considered to determine the shape of the tongue. The most common morphological feature on the dorsum of the tongue was the presence of central fissures. Multiple vertical fissures were observed in males whereas single vertical fissure was a common finding in females. The fissures were predominantly shallow in males and deep in females. The tongue was predominantly U shaped in males and females. V-shaped tongue was observed in 25% of females. Tongue prints are useful in biometric authentication. The methodology used in the study is simple, easy and can be adopted by dentists on a regular basis. However, large-scale studies are required to validate the results and also identify other features of the tongue that can be used in forensics and biometric authentication process.

Insights into early lithic technologies from ethnography

PubMed Central

Hayden, Brian

2015-01-01

Oldowan lithic assemblages are often portrayed as a product of the need to obtain sharp flakes for cutting into animal carcases. However, ethnographic and experimental research indicates that the optimal way to produce flakes for such butchering purposes is via bipolar reduction of small cryptocrystalline pebbles rather than from larger crystalline cores resembling choppers. Ethnographic observations of stone tool-using hunter-gatherers in environments comparable with early hominins indicate that most stone tools (particularly chopper forms and flake tools) were used for making simple shaft tools including spears, digging sticks and throwing sticks. These tools bear strong resemblances to Oldowan stone tools. Bipolar reduction for butchering probably preceded chopper-like core reduction and provides a key link between primate nut-cracking technologies and the emergence of more sophisticated lithic technologies leading to the Oldowan. PMID:26483534

On Macrosegregation

NASA Astrophysics Data System (ADS)

Ludwig, Andreas; Wu, Menghuai; Kharicha, Abdellah

2015-11-01

Macrosegregations, namely compositional inhomogeneities at a scale much larger than the microstructure, are typically classified according to their metallurgical appearance. In ingot castings, they are known as `A' and `V' segregation, negative cone segregation, and positive secondary pipe segregation. There exists `inverse' segregation at casting surfaces and `centerline' segregation in continuously cast slabs and blooms. Macrosegregation forms if a relative motion between the solute-enriched or -depleted melt and dendritic solid structures occurs. It is known that there are four basic mechanisms for the occurrence of macrosegregation. In the recent years, the numerical description of the combination of these mechanisms has become possible and so a tool has emerged which can be effectively used to get a deeper understanding into the process details which are responsible for the formation of the above-mentioned different macrosegregation appearances. Based on the most sophisticated numerical models, we consequently associate the four basic formation mechanisms with the physical phenomena happening during (i) DC-casting of copper-based alloys, (ii) DC-casting of aluminum-based alloys, (iii) continuous casting of steel, and (iv) ingot casting of steel.

A new method to acquire 3-D images of a dental cast

NASA Astrophysics Data System (ADS)

Li, Zhongke; Yi, Yaxing; Zhu, Zhen; Li, Hua; Qin, Yongyuan

2006-01-01

This paper introduced our newly developed method to acquire three-dimensional images of a dental cast. A rotatable table, a laser-knife, a mirror, a CCD camera and a personal computer made up of a three-dimensional data acquiring system. A dental cast is placed on the table; the mirror is installed beside the table; a linear laser is projected to the dental cast; the CCD camera is put up above the dental cast, it can take picture of the dental cast and the shadow in the mirror; while the table rotating, the camera records the shape of the laser streak projected on the dental cast, and transmit the data to the computer. After the table rotated one circuit, the computer processes the data, calculates the three-dimensional coordinates of the dental cast's surface. In data processing procedure, artificial neural networks are enrolled to calibrate the lens distortion, map coordinates form screen coordinate system to world coordinate system. According to the three-dimensional coordinates, the computer reconstructs the stereo image of the dental cast. It is essential for computer-aided diagnosis and treatment planning in orthodontics. In comparison with other systems in service, for example, laser beam three-dimensional scanning system, the characteristic of this three-dimensional data acquiring system: a. celerity, it casts only 1 minute to scan a dental cast; b. compact, the machinery is simple and compact; c. no blind zone, a mirror is introduced ably to reduce blind zone.

Effects of process variables on the properties of YBa2Cu3O(7-x) ceramics formed by investment casting

NASA Technical Reports Server (NTRS)

Hooker, M. W.; Taylor, T. D.; Leigh, H. D.; Wise, S. A.; Buckley, J. D.; Vasquez, P.; Buck, G. M.; Hicks, L. P.

1993-01-01

An investment casting process has been developed to produce net-shape, superconducting ceramics. In this work, a factorial experiment was performed to determine the critical process parameters for producing cast YBa2Cu3O7 ceramics with optimum properties. An analysis of variance procedure indicated that the key variables in casting superconductive ceramics are the particle size distribution and sintering temperature. Additionally, the interactions between the sintering temperature and the other process parameters (e.g., particle size distribution and the use of silver dopants) were also found to influence the density, porosity, and critical current density of the fired ceramics.

PRODUCTION OF THORIA WARE

DOEpatents

Murray, P.; Denton, I.; Wilkinson, D.

1957-10-01

The production of thoria ware of very low porosity by the slip casting of pure thoria is described. It comprises dry milling calcined thoria to obtain particles ranging up to 11 microns in size and having 60% of particles less than 2 microns, forming an aqueous slip of the milled thoric casting the slip and firing the dry cast at a sintering temperature of from 1600 to 1825 d C. The preferred composition of the slip is 1600 grams of thoria in each liter of slip. The preferred pH of the slip is 1. When thoria of 99.9% purity is used the slip is suitable for casting for as long as six weeks after preparation.

Indigenous lunar construction materials

NASA Technical Reports Server (NTRS)

Rogers, Wayne; Sture, Stein

1991-01-01

The objectives are the following: to investigate the feasibility of the use of local lunar resources for construction of a lunar base structure; to develop a material processing method and integrate the method with design and construction of a pressurized habitation structure; to estimate specifications of the support equipment necessary for material processing and construction; and to provide parameters for systems models of lunar base constructions, supply, and operations. The topics are presented in viewgraph form and include the following: comparison of various lunar structures; guidelines for material processing methods; cast lunar regolith; examples of cast basalt components; cast regolith process; processing equipment; mechanical properties of cast basalt; material properties and structural design; and future work.

Self-assembly Morphology and Crystallinity Control of Di-block Copolymer Inspired by Spider Silk

NASA Astrophysics Data System (ADS)

Huang, Wenwen; Krishnaji, Sreevidhya; Kaplan, David; Cebe, Peggy

2012-02-01

To obtain a fuller understanding of the origin of self-assembly behavior, and thus be able to control the morphology of biomaterials with well defined amino acid sequences for tissue regeneration and drug delivery, we created a family of synthetic silk-based block copolymers inspired by the genetic sequences found in spider dragline, HABn and HBAn (n=1,2,3,6), where B = hydrophilic block, A = hydrophobic block, and H is a histidine tag. We assessed the secondary structure of water cast films by Fourier transform infrared spectroscopy (FTIR). The crystallinity was determined by Fourier self-deconvolution of amide I spectra and confirmed by wide angle X-ray diffraction (WAXD). Results indicate that we can control the self-assembled morphology and the crystallinity by varying the block length, and a minimum of 3 A-blocks are required to form beta sheet crystalline regions in water-cast spider silk block copolymers. The morphology and crystallinity can also be tuned by annealing. Thermal properties of water cast films and films annealed at 120 C were determined by differential scanning calorimetry and thermogravimetry. The sample films were also treated with 1,1,1,3,3,3-Hexafluoro-2-propanol (HFIP) to obtain wholly amorphous samples, and crystallized by exposure to methanol. Using scanning and transmission electron microscopies, we observe that fibrillar networks and hollow micelles are formed in water cast and methanol cast samples, but not in samples cast from HFIP.

Thermomechanical processing of microalloyed powder forged steels and a cast vanadium steel

NASA Astrophysics Data System (ADS)

Dogan, B.; Davies, T. J.

1985-09-01

The effects of controlled rolling on transformation behavior of two powder forged (P/F) microalloyed vanadium steels and a cast microalloyed vanadium steel were investigated. Rolling was carried out in the austenitic range below the recrystallization temperature. Equiaxed grain structures were produced in specimens subjected to different reductions and different cooling rates. The ferrite grain size decreased with increasing deformation and cooling rate. Ferrite nucleated on second phase particles, deformation bands, and on elongated prior austenite grain boundaries; consequently a high fractional ferrite refinement was achieved. Deformation raised the ferrite transformation start temperature while the time to transformation from the roll finish temperature decreased. Cooling rates in the cast steel were higher than in P/F steels for all four cooling media used, and the transformation start temperatures of cast steels were lower than that of P/F steel. Intragranular ferrite nucleation, which played a vital role in grain refinement, increased with cooling rate. Fully bainitic microstructures were formed at higher cooling rates in the cast steel. In the P/F steels inclusions and incompletely closed pores served as sites for ferrite nucleation, often forming a ‘secondary’ ferrite. The rolling schedule reduced the size of large pores and particle surface inclusions and removed interconnected porosity in the P/F steels.

Modelling the Cast Component Weight in Hot Chamber Die Casting using Combined Taguchi and Buckingham's π Approach

NASA Astrophysics Data System (ADS)

Singh, Rupinder

2018-02-01

Hot chamber (HC) die casting process is one of the most widely used commercial processes for the casting of low temperature metals and alloys. This process gives near-net shape product with high dimensional accuracy. However in actual field environment the best settings of input parameters is often conflicting as the shape and size of the casting changes and one have to trade off among various output parameters like hardness, dimensional accuracy, casting defects, microstructure etc. So for online inspection of the cast components properties (without affecting the production line) the weight measurement has been established as one of the cost effective method (as the difference in weight of sound and unsound casting reflects the possible casting defects) in field environment. In the present work at first stage the effect of three input process parameters (namely: pressure at 2nd phase in HC die casting; metal pouring temperature and die opening time) has been studied for optimizing the cast component weight `W' as output parameter in form of macro model based upon Taguchi L9 OA. After this Buckingham's π approach has been applied on Taguchi based macro model for the development of micro model. This study highlights the Taguchi-Buckingham based combined approach as a case study (for conversion of macro model into micro model) by identification of optimum levels of input parameters (based on Taguchi approach) and development of mathematical model (based on Buckingham's π approach). Finally developed mathematical model can be used for predicting W in HC die casting process with more flexibility. The results of study highlights second degree polynomial equation for predicting cast component weight in HC die casting and suggest that pressure at 2nd stage is one of the most contributing factors for controlling the casting defect/weight of casting.

Flux-vector splitting algorithm for chain-rule conservation-law form

NASA Technical Reports Server (NTRS)

Shih, T. I.-P.; Nguyen, H. L.; Willis, E. A.; Steinthorsson, E.; Li, Z.

1991-01-01

A flux-vector splitting algorithm with Newton-Raphson iteration was developed for the 'full compressible' Navier-Stokes equations cast in chain-rule conservation-law form. The algorithm is intended for problems with deforming spatial domains and for problems whose governing equations cannot be cast in strong conservation-law form. The usefulness of the algorithm for such problems was demonstrated by applying it to analyze the unsteady, two- and three-dimensional flows inside one combustion chamber of a Wankel engine under nonfiring conditions. Solutions were obtained to examine the algorithm in terms of conservation error, robustness, and ability to handle complex flows on time-dependent grid systems.

Rapakivi Granite: An architectural emblem of St Petersburg and its utilisation in other world cities

NASA Astrophysics Data System (ADS)

Bulakh, Andrey; Gavrilenko, Vladimir; Panova, Helen

2015-04-01

The wide-ranging utilisation of Rapakivi Granite in St Petersburg is typified by the the famous Alexander Column, and 114 stone columns of St Isaac's Cathedralas well as the pedestal of the Nicholas I monument, and portals and basements of buildings of the Admiralty, General Staff, Senate and Synod. The stone is also frequently seen among pavement slabs and in parapets of embankments and bridges around the city. This list of examples where Rapakivi Granite has been used could be expanded further. All Rapakivi Granites used in the buildings of St.Petersburg were quarried from the so-called Vyborg massif. At present it has been found that the massif occupies an area of about 18 000 km2. In the past granite of the Vyborg massif was worked from several quarries in the vicinity of Fredrikshamn (Hamina) in Finland for use in St Peterburg. The best known granite quarries are at Piterlaks (Piuterlahti) and Gimmekyul (Hämeenkylä). Sometimes Rapakivi Granite form Finland differs in appearance from typical varieties. Thus columns of a classical portal in the house at N 7 in Pochtamtskaya Street are hewn from this greyish variety. Other examples are the plinth of the General Staff and Trade Store buildings. After the 1960s varieties from the Leningrad district, and Korosten (Ukraine) massifs were used in St Petersburg. Today it is possible to find examples of Rapakivi Granite from Finland in cities in the USA, South Africa, United Kingdom and Germany. It is a long used stone as demonstrated by its cultural heritage. It is also used as an ornamental or decorative stone in modern architecture. References: 1) Bulakh, A.G., Abakumova, N.B., and Romanovsky, J.V. St Petersburg: a History in Stone. 2010. Print House of St Petersburg State University. 173 p. (In English). 2) Tutakova, A.Ya., Romanovskiy, A.Z., Bulakh, A.G., and Leer, V.I. Dimension Stone of the Leningrad Region. Granites of the Karelia Isthmus in Architecture of the Modern St Petersburg. 2011. St Petersburg. 78 p. (In Russian). 3) Bulakh, A. G. Stone Town Guide, St Petersburg, 1-5. URL: [PDF] stone - GTK - Projects projects.gtk.fi/export/.../Bulakh_Stone_Guide 4) Paavo, H, Selonen, O, Luodes, H. The Wiborg Granite Batholith. The Main Production Area for Granite in Finland. Engineering Geology for Society and Territory - Volume 5. Springer. 2015. P. 259-262. 5) Bulakh, A. G. Ornamental Stone in the History of St Petersburg Architecture. Geological Society, London, 2015. SP407. Global Heritage Stone: Towards International Recognition of Building and Ornamental Stones.

Microstructures of ancient and modern cast silver–copper alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Northover, S.M., E-mail: s.m.northover@open.ac.uk; Northover, J.P., E-mail: peter.northover@materials.ox.ac.uk

The microstructures of modern cast Sterling silver and of cast silver objects about 2500 years old have been compared using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM), energy dispersive X-ray microanalysis (EDX) and electron backscatter diffraction (EBSD). Microstructures of both ancient and modern alloys were typified by silver-rich dendrites with a few pools of eutectic and occasional cuprite particles with an oxidised rim on the outer surface. EBSD showed the dendrites to have a complex internal structure, often involving extensive twinning. There was copious intragranular precipitation within the dendrites, in themore » form of very fine copper-rich rods which TEM, X-ray diffraction (XRD), SEM and STEM suggest to be of a metastable face-centred-cubic (FCC) phase with a cube–cube orientation relationship to the silver-rich matrix but a higher silver content than the copper-rich β in the eutectic. Samples from ancient objects displayed a wider range of microstructures including a fine scale interpenetration of the adjoining grains not seen in the modern material. Although this study found no unambiguous evidence that this resulted from microstructural change produced over archaeological time, the copper supersaturation remaining after intragranular precipitation suggests that such changes, previously proposed for wrought and annealed material, may indeed occur in ancient silver castings. - Highlights: • Similar twinned structures and oxidised surfaces seen in ancient and modern cast silver • General precipitation of fine Cu-rich rods apparently formed by discontinuous precipitation is characteristic of as-cast silver. • The fine rods are cube-cube related to the matrix in contrast with the eutectic. • The silver-rich phase remains supersaturated with copper. • Possibly age-related grain boundary features seen in ancient cast silver.« less

Thermodynamic Behavior Research Analysis of Twin-roll Casting Lead Alloy Strip Process

NASA Astrophysics Data System (ADS)

Jiang, Chengcan; Rui, Yannian

2017-03-01

The thermodynamic behavior of twin-roll casting (TRC) lead alloy strip process directly affects the forming of the lead strip, the quality of the lead strip and the production efficiency. However, there is little research on the thermodynamics of lead alloy strip at home and abroad. The TRC lead process is studied in four parameters: the pouring temperature of molten lead, the depth of molten pool, the roll casting speed, and the rolling thickness of continuous casting. Firstly, the thermodynamic model for TRC lead process is built. Secondly, the thermodynamic behavior of the TRC process is simulated with the use of Fluent. Through the thermodynamics research and analysis, the process parameters of cast rolling lead strip can be obtained: the pouring temperature of molten lead: 360-400 °C, the depth of molten pool: 250-300 mm, the roll casting speed: 2.5-3 m/min, the rolling thickness: 8-9 mm. Based on the above process parameters, the optimal parameters(the pouring temperature of molten lead: 375-390 °C, the depth of molten pool: 285-300 mm, the roll casting speed: 2.75-3 m/min, the rolling thickness: 8.5-9 mm) can be gained with the use of the orthogonal experiment. Finally, the engineering test of TRC lead alloy strip is carried out and the test proves the thermodynamic model is scientific, necessary and correct. In this paper, a detailed study on the thermodynamic behavior of lead alloy strip is carried out and the process parameters of lead strip forming are obtained through the research, which provide an effective theoretical guide for TRC lead alloy strip process.

Low Cost Al-Si Casting Alloy As In-Situ Composite for High Temperature Applications

NASA Technical Reports Server (NTRS)

Lee, Jonathan A.

2000-01-01

A new aluminum-silicon (Al-Si) alloy has been successfully developed at NASA- Marshall Space Flight Center (MSFC) that has significant improvement in tensile and fatigue strength at elevated temperatures (500 F-700 F). The alloy offers a number of benefits such as light weight, high hardness, low thermal expansion and high surface wear resistance. In hypereutectic form, this alloy is considered as an in-situ Al-Si composite with tensile strength of about 90% higher than the auto industry 390 alloy at 600 F. This composite is very economically produced by using either conventional permanent steel molds or die casting. The projected material cost is less than $0.90 per pound, and automotive components such as pistons can be cast for high production rate using conventional casting techniques with a low and fully accounted cost. Key Words: Metal matrix composites, In-situ composite, aluminum-silicon alloy, hypereutectic alloy, permanent mold casting, die casting.

Effects of Casting Conditions on End Product Defects in Direct Chill Casted Hot Rolling Ingots

NASA Astrophysics Data System (ADS)

Yorulmaz, Arda; Yüksel, Çağlar; Erzi, Eraz; Dispinar, Derya

Direct chill casting is a reliable casting process for almost any wrought aluminum alloy for subsequent deformation via hot rolling to supply vital industries such as aerospace, automotive, construction, packaging and maritime. While some defects occur during casting, like hot tearing, some others like surface defect causing blisters, appear after hot rolling process or annealing after final cold rolling steps. It was found that some of these defects are caused by melt impurities formed from entrained folded aluminum oxides or bifilms. A study in a hot rolling casting facility was carried out with different melt cleaning practices, launder and molten metal transferring designs. Bifilm index and reduced pressure test were used for determining melt cleanliness measurement. It was found that porous plug gas diffusons for degassing are more effective than lance type degassers and a design towards less turbulent molten metal flow from furnace to mould cavity are necessary for reducing defects caused by bifilms.

Hydroxyapatite scaffolds processed using a TBA-based freeze-gel casting/polymer sponge technique.

PubMed

Yang, Tae Young; Lee, Jung Min; Yoon, Seog Young; Park, Hong Chae

2010-05-01

A novel freeze-gel casting/polymer sponge technique has been introduced to fabricate porous hydroxyapatite scaffolds with controlled "designer" pore structures and improved compressive strength for bone tissue engineering applications. Tertiary-butyl alcohol (TBA) was used as a solvent in this work. The merits of each production process, freeze casting, gel casting, and polymer sponge route were characterized by the sintered microstructure and mechanical strength. A reticulated structure with large pore size of 180-360 microm, which formed on burn-out of polyurethane foam, consisted of the strut with highly interconnected, unidirectional, long pore channels (approximately 4.5 microm in dia.) by evaporation of frozen TBA produced in freeze casting together with the dense inner walls with a few, isolated fine pores (<2 microm) by gel casting. The sintered porosity and pore size generally behaved in an opposite manner to the solid loading, i.e., a high solid loading gave low porosity and small pore size, and a thickening of the strut cross section, thus leading to higher compressive strengths.

Effect of soda consumption on urinary stone risk parameters.

PubMed

Passman, Corey M; Holmes, Ross P; Knight, John; Easter, Linda; Pais, Vernon; Assimos, Dean G

2009-03-01

Fluid consumption has been demonstrated to influence kidney stone formation. Studies have shown that consumption of cola may be a risk factor for stone disease, while fluids containing citric acid may attenuate stone activity. Diet was not always controlled in these investigations, however. We undertook a study to determine the impact of three different fluids on urinary stone risk factors. Six healthy nonstone-forming adults were placed on a standardized metabolic diet and consumed three different types of fluid during three 5-day periods. There was a 2-day washout between each sequence. The three fluids administered during these periods were Le Bleu water, caffeine-free Diet Coke, and Fresca (citrate containing). These two soda preparations were chosen to prevent the known increase in calcium excretion promoted by carbohydrates and caffeine. Twenty-four hour urine specimens were collected on days 4 and 5 of each sequence. The following urinary parameters were measured: Volume, calcium, oxalate, creatinine, uric acid, citrate, sodium, magnesium, phosphorus, sulfate, urea nitrogen, pH, and supersaturation indices. A paired t test was used for statistical analysis. Urinary volumes were significantly higher and supersaturation of calcium oxalate significantly lower compared with a self-selected dietary regimen. A decrease in uric acid was also seen in the Fresca cohort. There were no statistically significant differences for any of the urinary parameters. There is no increased risk or benefit to consuming Fresca or caffeine-free Diet Coke compared with Le Bleu bottled water with respect to stone formation.

[Intraoperative choledochoscopy usefulness in the treatment of difficult biliary stones].

PubMed

Cuendis-Velázquez, A; Rojano-Rodríguez, M E; Morales-Chávez, C E; González Angulo-Rocha, A; Fernández-Castro, E; Aguirre-Olmedo, I; Torres-Ruiz, M F; Orellana-Parra, J C; Cárdenas-Lailson, L E

2014-01-01

Choledocholithiasis presents in 5-10% of the patients with biliary lithiasis. Numerous treatment algorithms have been considered for this disease, however, up to 10% of these therapeutic procedures may fail. Intraoperative choledochoscopy has become a useful tool in the treatment of patients with difficult-to-manage choledocholithiasis. To determine the usefulness of intraoperative choledochoscopy in the laparoendoscopic treatment of difficult stones that was carried out in our service. A cross-sectional study was conducted. The case records were reviewed of the patients that underwent intraoperative choledochoscopy during biliary tree exploration plus laparoscopic choledochoduodenal anastomosis within the time frame of March 1, 2011 and May 31, 2012, at the Hospital General Dr. Manuel Gea González. Transabdominal choledochoscopies were performed with active stone extraction when necessary, followed by peroral choledochoscopies through the recently formed bilioenteric anastomosis. The data were analyzed with descriptive statistics and measures of central tendency. The mean age was 71 years, 57% of the patients were women, and the ASA III score predominated. Active extraction of stones with 7 to 35mm diameters was carried out in 4 of the cases and the absence of stones in the biliary tract was corroborated in all the patients. The mean surgery duration was 18 minutes (range: 4 to 45min). Choledochoscopy is a safe and effective minimally invasive procedure for the definitive treatment of difficult stones. Copyright © 2013 Asociación Mexicana de Gastroenterología. Published by Masson Doyma México S.A. All rights reserved.

Electrokinetic lithotripsy: safety, efficacy and limitations of a new form of ballistic lithotripsy.

PubMed

Keeley, F X; Pillai, M; Smith, G; Chrisofos, M; Tolley, D A

1999-08-01

To investigate the safety and efficacy of electrokinetic lithotripsy (EKL), a ballistic lithotripter which uses high-energy magnetic fields to propel an impactor to fragment calculi. The records and radiographs of 121 patients who underwent ureteroscopy using the EKL for stones in the upper (26), mid (28) or lower (67) ureter were reviewed retrospectively. Ureteroscopy was performed with an 8.5 F semi-rigid ureteroscope, through which a 3 F EKL probe was passed. A total of 148 stones (mean stone size 11.5 mm, range 6-40) in 121 patients were treated using the EKL. One patient was lost to follow-up. Of 148 stones, 147 (99.3%) were fragmented, including five that had resisted fragmentation with either pulsed-dye laser or electrohydraulic lithotripsy. Despite this, only 45 of 56 patients (80%) with a single stone in the lower ureter were rendered stone-free after a single ureteroscopic procedure. Seven patients in this group (12%) required shock-wave lithotripsy for fragments that had been propelled into the kidney, while four patients (7%) required repeat ureteroscopy for retained ureteric fragments. Complications were limited to minor ureteric perforations in two patients, both of which were treated with a stent. EKL is an inexpensive and reliable endoscopic method which fragments nearly all urinary calculi. Its limitations include the propulsion of fragments and the need to use an offset, semi-rigid ureteroscope. We recommend the use of a basket or graspers to remove fragments of >/=4 mm after EKL.

Novel porcine model for calcium oxalate stone formation.

PubMed

Trojan, Brandon P; Trojan, Sara J; Navetta, Andrew; Staches, Bryce; Sutton, Bryan; Filleur, Stephanie; Nelius, Thomas

2017-10-01

Mechanisms for calcium-based stone formation are not clearly delineated. Porcine are the most anatomically and physiologically congruent mammal to humans. Our objectives were to develop a cost-effective and easily reproducible porcine model for the study of calcium-based nephrolithiasis. Crossbred male pigs (n = 16) were assigned randomly to one of the following treatments: (1) control; (2) ethylene glycol (EG) + vitamin D (VD); (3) EG + ammonium chloride (AC); (4) EG + gentamicin (G); (5) EG + Lasix; (6) EG + VD + AC; (7) EG + VD + G. Treatments were administered for 28 days; blood and urine were collected on day 0, 14, and 28. At the endpoint of the study, renal tissue was collected for gross and microscopic analysis of crystal stone formation and inflammation. Stone-forming parameters were observed in serum and urine. For control versus all other treatments, by day 28, serum BUN and creatinine were less (P < 0.01), urinary creatinine, citrate and pH were greater (P < 0.01), and urinary oxalate was less (P < 0.01). Histopathological analysis of H&E staining and stone analysis revealed formation of calcium oxalate stones and crystal formation within the renal cortex and medulla for all animals except control. Nephrotoxicity was observed in one animal from treatment EG + G. The treatments explored in this experiment provided novel examples of cost-effective porcine models for the study of nephrolithiasis. EG + VD had the strongest indicators of nephrolithiasis without nephrotoxicity.

Development of Aerogel Molds for Metal Casting Using Lunar and Martian Regolith

NASA Technical Reports Server (NTRS)

2003-01-01

In the last few years NASA has set new priorities for research and development of technologies necessary to enable long-term presence on the Moon and Mars. Among these key technologies is what is known as in situ resource utilization, which defines all conceivable usage of mineral, liquid, gaseous, or biological resources on a visited planet. In response to this challenge, we have been focusing on developing and demonstrating the manufacturing of a specific product using Lunar and Martian soil simulants (i.e., a mold for the casting of metal and alloy parts) which will be an indispensable tool for the survival of outposts on the Moon and Mars. In addition, our purpose is to demonstrate the feasibility of using mesoporous materials such as aerogels to serve as efficient casting molds for high quality components in propulsion and other aerospace applications. The first part of the project consists of producing aerogels from the in situ resources available in Martian and Lunar soil. The approach we are investigating is to use chemical processes to solubilize silicates using organic reagents at low temperatures and then use these as precursors in the formation of aerogels for the fabrication of metal casting molds. One set of experiments consists of dissolving silica sources in basic ethylene glycol solution to form silicon glycolates. When ground silica aerogel was used as source material, a clear solution of silicon glycolate was obtained and reacted to form a gel thus proving the feasibility of this approach. The application of this process to Lunar and Martian simulants did not result in the formation of a gel; further study is in progress. In the second method acidified alcohol is reacted with the simulants to form silicate esters. Preliminary results indicate the presence of silicon alkoxide in the product distillation. However, no gel has been obtained so further characterization is ongoing. In the second part of the project, the focus has been on developing a series of aerogel plates suitable for thin plate metal casting and ingot metal castings. The influence of aerogels on thin wall metal castings was studied by placing aerogel plates into the cavities of thin sections of resin bonded sand molds. An 1 based commercial alloy ( 356) containing 7 percent Si was poured into these molds. Post-solidification studies provide evidence that aerogel inserts significantly reduce the cooling rate during solidification. The advantage of a lower rate using aerogel inserts was reflected in the reduction of casting defects such as shrinkage porosity. Quantitative results support the hypothesis that using aerogels as a mold material can offer definite advantages when used as casting thin sections. As a separate effort, silica aerogel with cylindrical cavities have been prepared and will be evaluated for casting commercial alloys.

Fossilized diatoms in meteorites from recent falls in Sri Lanka

NASA Astrophysics Data System (ADS)

Hoover, Richard B.; Wallis, Jamie; Wickramarathne, Keerthi; Samaranayake, Anil; Williams, George; Jerman, Gregory; Wallis, D. H.; Wickramasinghe, N. C.

2013-09-01

On December 29, 2012, a bright yellow and green fireball was observed to disintegrate over the Polonnaruwa District of North Central, Sri Lanka. Many low density, black stones were recovered soon after the observed fall from rice paddy fields near the villages of Aralaganwila and Dimbulagala. These stones were initially studied by optical microscopy methods at the Medical Research Institute in Colombo, Sri Lanka. Soon thereafter, samples were sent to the UK and to the United States. More extensive Field Emission Scanning Electron Microscopy studies were then carried out at Cardiff University and the NASA/Marshall Space Flight Center. The physico-chemical properties, elemental abundances, mineralogy and stable isotope data clearly indicate that these stones are non-terrestrial. Freshly fractured interior surfaces of the black stones have also been observed to contain the remains of fossilized diatom. Many of the diatom frustules are clearly embedded in the meteorite rock matrix and exhibit nitrogen levels below the EDX detection limits. Some of the fossil diatoms are araphid marine pennates and planktonic forms that are inconsistent with conditions associated with rice paddy fields. These observations indicate the fossilized diatoms are indigenous to the meteorites rather than post-arrival biological contaminants. The carbon content and mineralogy suggests that these stones may represent a previously ungrouped clan of carbonaceous meteorites. The extremely low density (~0.6) of the stones and their observed mineralogy was inconsistent with known terrestrial rocks (e.g., pumice, diatomite and fulgurites). The minerals detected suggest that the parent body of the Polonnaruwa stones may have been the nucleus of a comet. These observations are interpreted as supporting the Hoyle-Wickramasinghe Panspermia hypothesis and the hypothesis that diatoms and other microorganisms might be capable of living and growing in water ice and brines in comets.

Significant differences in struvite and cystine stone frequency seen among Chinese nephrolithiasis patients living in North America compared to those living in China

PubMed Central

Chi, Thomas; Usawachintachit, Manint; Filippou, Pauline; Bayne, David; Hu, Weiguo; Chang, Helena; Xia, Lei; Chen, Qi; Xue, Wei; He, Hui; Long, Qingzhi; Arsovska, Olga; Taylor, Eric; Paterson, Ryan; Sur, Roger L.; Chew, Ben; Stoller, Marshall L.

2016-01-01

Background Interracial disparities in nephrolithiasis prevalence have been reported, but the interplay between genetics and the environment for urinary stone disease risk factors is poorly understood. To examine how environment may alter genetic predisposition for stone formation, we established the International Chinese Consortium on Nephrolithiasis (ICCON) as a multi-institutional collaboration to examine patterns of nephrolithiasis presentation between Chinese patients living in different countries. Methods Chinese patients undergoing percutaneous nephrolithotomy (PCNL) at six participating institutions in China and North America over 4 years were reviewed retrospectively. Patient demographics and clinical data were compared between Chinese patients living in China and North America. Results A total of 806 patients were included, encompassing 721 Chinese patients living in China and 85 living in North America. Nephrolithiasis patients living in China were more likely to be male (67% vs. 56%, P=0.02), present at a younger age (48.6±15.0 vs. 55.0±13.0 years, P<0.01), and have a lower BMI (24.6±4.0 vs. 25.9±5.7, P=0.04) but were less likely to form struvite stones (5.5% vs. 14.1%, P<0.01). No cystine stone patients were seen in North American Chinese patients, whereas 1.8% of nephrolithiasis patients living in China presented with cystine stones. Similar rates of calcium-based and uric acid calculi as well as urinary pH were seen among both groups. Conclusions Significant differences exist between Chinese nephrolithiasis patients living in China compared to those living in North America, highlighting the importance of environmental factors in addition to genetics in modulating risk for urinary stone disease. PMID:27298786

Lithotripsy of gallstones by means of a quality-switched giant-pulse neodymium:yttrium-aluminum-garnet laser. Basic in vitro studies using a highly flexible fiber system.

PubMed

Hochberger, J; Gruber, E; Wirtz, P; Dürr, U; Kolb, A; Zanger, U; Hahn, E G; Ell, C

1991-11-01

The quality-switched neodymium:yttrium-aluminum-garnet laser represents a new instrument for athermal fragmentation of gallstones by transformation of optical energy into mechanical energy in the form of shock waves via local plasma formation. A highly flexible 300-micron fiber transmission system was used in basic investigations to determine the influence of varying pulse repetition rates (5-30 Hz) and pulse energies (15 and 20 mJ) on shock wave intensity and stone fragmentation in vitro for 105 biliary calculi of known size and chemical composition. After performance of 1200 shock wave pressure measurements using polyvinylidenefluoride hydrophones, stone fragmentation was analyzed by determination of fragment removal rates (volume of fragments removed per fragmentation time), ablation rates (mean volume removed per laser pulse), and median fragment sizes for each laser setting. With the quality-switched neodymium:yttrium-aluminum-garnet laser system, all concrements could be reliably disintegrated into small fragments (median diameter, 0.7-1.7 mm). Compared with pure cholesterol stones, a significantly higher fragment removal rate was achieved in cholesterol stones containing 30% calcium phosphate (P = 0.039), in cholesterol stones containing 20% pigment (P = 0.015), and in pure pigment stones (P = 0.007). Fragment removal rates, local shock wave pressures, and median grain sizes were significantly higher at a pulse energy of 20 mJ than with 15 mJ. Shock wave pressures showed a distinct dependence on pulse repetition rates at 20 mJ, yet not at 15 mJ. Because there is no evident hazard of thermal damage to tissue using the quality-switched neodymium:yttrium-aluminum-garnet laser, it appears to be a promising device for nonsurgical biliary stone therapy.

Laboratory exposure systems to simulate atmospheric degradation of building stone under dry and wet deposition conditions

NASA Astrophysics Data System (ADS)

Johnson, J. B.; Haneef, S. J.; Hepburn, B. J.; Hutchinson, A. J.; Thompson, G. E.; Wood, G. C.

The design philosophy, construction and use of two exposure test systems are described, in which the objective is to simulate the degradation of stone samples under, respectively, the 'dry' and 'wet' deposition of atmospheric pollutants. Some element of realistic acceleration is possible in certain experiments. Particular emphasis is placed upon using known presentation rates of the pollutants, both in respect of typical depositions of pollutants and their oxidation products appropriate for an industrial atmosphere. In the dry deposition rig, SO 2, NO 2, NO, HCl and the oxidant O 3 are presented individually or together at realistic deposition rates. In the wet deposition apparatus, SO 2-4, NO -3 and Cl - at a pH of 3.5, simulating 'acid rain' but in a more concentrated form, are deposited. The dry deposition chamber can be operated at constant relative humidity (typically 84%) with pre-dried or precisely wetted stones to simulate episodic rain wetting, or using other methods of wet/dry cycling, which are also a feature of the wet deposition chamber. Heating and cooling of the samples is also possible, as is the use of shaped or coupled stones of different kinds such as are found in a building facade. The results are illustrated in terms of data on the weight change, the anion content of stone and run-off, the pH change of run-off and the total calcium reacted, using Portland stone, as a prelude to later papers in which behaviour of a whole matrix of stone types and environments is presented and discussed. Such an approach permits the eventual production of 'pollutant-material response' relationships and damage functions for comparison with and prediction of external exposure results.

The risk of renal stone formation during and after long duration space flight

NASA Technical Reports Server (NTRS)

Whitson, P. A.; Pietrzyk, R. A.; Morukov, B. V.; Sams, C. F.

2001-01-01

BACKGROUND: The formation of a renal stone during space flight may have serious negative effects on the health of the crewmember and the success of the mission. Urinary biochemical factors and the influence of dietary factors associated with renal stone development were assessed during long duration Mir Space Station missions. METHODS: Twenty-four-hour urine samples were collected prior to, during and following long duration space flight. The relative urinary supersaturation of calcium oxalate, calcium phosphate (brushite), sodium urate, struvite and uric acid were determined. RESULTS: Changes in the urinary biochemistry of crewmembers during long duration spaceflight demonstrated increases in the supersaturation of the stone-forming salts. In-flight hypercalciuria was evident in a number of individual crewmembers and 24-hour dietary fluid intake and urine volume were significantly lower. During flight, there was a significant increase in brushite supersaturation. CONCLUSIONS: These data suggest acute effects of space flight and postflight changes in the urinary biochemistry favoring increased crystallization in the urine. The effects of dietary intake, especially fluid intake, may have a significant impact on the potential for renal stone formation. Efforts are now underway to assess the efficacy of a countermeasure to mitigate the increased risk. Copyright 2001 S. Karger AG, Basel.

Laser-induced breakdown spectroscopy-Raman: An effective complementary approach to analyze renal-calculi.

PubMed

Muhammed Shameem, K M; Chawla, Arun; Mallya, Madhukar; Barik, Bijay Kumar; Unnikrishnan, V K; Kartha, V B; Santhosh, C

2018-06-01

Presence of renal-calculi (kidney stones) in human urethra is being increasingly diagnosed over the last decade and is considered as one of the most painful urological disorders. Accurate analysis of such stones plays a vital role in the evaluation of urolithiasis patients and in turn helps the clinicians toward exact etiologies. Two highly complementary laser-based analytical techniques; laser-induced breakdown spectroscopy (LIBS) and micro-Raman spectroscopy have been used to identify the chemical composition of different types of renal-calculi. LIBS explores elemental characteristics while Raman spectroscopy provides molecular details of the sample. This complete information on the sample composition might help clinicians to identify the key aspects of the formation of kidney stones, hence assist in therapeutic management and to prevent recurrence. The complementarity of both techniques has been emphasized and discussed. LIBS spectra of different types of stones suggest the probable composition of it by virtue of the major, minor and trace elements detected from the sample. However, it failed to differentiate the crystalline form of different hydrates of calcium oxalate stone. This lacuna was overcome by the use of Raman spectroscopy and these results are compared with conventional chemical analysis. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Method for uniformly distributing carbon flakes in a positive electrode, the electrode made thereby and compositions. [Patent application

DOEpatents

Mrazek, F.C.; Smaga, J.A.; Battles, J.E.

1981-01-19

A positive electrode for a secondary electrochemical cell is described wherein an electrically conductive current collector is in electrical contact with a particulate mixture of gray cast iron and an alkali metal sulfide and an electrolyte including alkali metal halides or alkaline earth metal halides. Also present may be a transition metal sulfide and graphite flakes from the conversion of gray cast iron to iron sulfide. Also disclosed is a method of distributing carbon flakes in a cell wherein there is formed an electrochemical cell of a positive electrode structure of the type described and a suitable electrolyte and a second electrode containing a material capable of alloying with alkali metal ions. The cell is connected to a source of electrical potential to electrochemically convert gray cast iron to an iron sulfide and uniformly to distribute carbon flakes formerly in the gray cast iron throughout the positive electrode while forming an alkali metal alloy in the negative electrode. Also disclosed are compositions useful in preparing positive electrodes.

Urolithiasis analysis in a multiethnic population at a tertiary hospital in Nairobi, Kenya.

PubMed

Wathigo, Francis K; Hayombe, Alfred; Maina, Daniel

2017-04-20

Urolithiasis is a global problem whose incidence is reported to be on the rise across the world. Previously, urolithiasis was reported as being rare among the indigenous African population but recent data suggest otherwise. This study reviewed the demographic and clinical characteristics of patients with urolithiasis seen at the Aga Khan University hospital Nairobi (AKUHN) as well as the chemical composition of the stones and the modalities of therapy used. This was a retrospective study which utilized patients' clinical and laboratory records from 2013 to 2014. Sixty-seven symptomatic patients with confirmed urolithiasis formed the study. This study aimed to describe the clinical characteristics of patients, modalities of treatment as well as the chemical composition of renal stones from patients diagnosed and managed for urolithiasis during a duration spanning 17 months. Wet chemistry was utilized for analyzing the chemical composition of the urinary calculi. Data on age, sex, symptoms, radiological investigations done, location of the calculi, chemical composition of calculi and therapeutic procedures instituted were extracted and analyzed. Ages ranged from 3 to 87 years with a median of 42; males were the majority (79%) and the commonest presenting symptoms were flank pain (91%) and dysuria (19%). The majority of the stones were located in the ureters (46%) and at the pelvi-ureteric junction (25%). A statistically significant difference in frequency of lodgment at the pelvi-ureteric site between males and females was noted. However, the number of female patients in this study was small and studies with larger numbers of female participants are required to confirm this observation. All stones contained calcium and oxalate, often as the only constituents (72%). In the remainder of the stones, other constituents such bicarbonate, ammonium, phosphorous, magnesium, uric acid and cystine occurred in varying combinations with calcium oxalate. Laser lithotripsy was the most performed therapeutic procedure (77.6%). Males formed the majority of patient with urolithiasis. Overall, most of the calculi were located in the ureters except in women where the pelviureteric location was commoner. Stones containing calcium oxalate only were predominant across the age groups and in both sexes. Lithotripsy was the commonest mode of management.

Ornamental Stones and Gemstones: The limits of heritage stone designation: The case for and against Australian Precious Opal

NASA Astrophysics Data System (ADS)

Cooper, Barry

2015-04-01

When the international designation of natural stone types was first mooted in 2007, stones that were utilised in building and construction were the primary focus of attention. However following public discussion it soon became apparent that sculptural stones, stone used for utilitarian purposes such as millstones, as well as archaeological materials including stones used by early man could all be positively assessed as a potential Global Heritage Stone Resource (GHSR). Over the past 2 years it has been realised there is also a range of ornamental and semi-precious stones that may also be considered in the same international context. Examples in this respect include Imperial Porphyry sourced from Egypt that was much prized in the ancient world and "Derbyshire Blue John" a variety of fluorspar from central England that was used for vases, chalices, urns, candle sticks, jars, bowls door, jewellery and fire-place surrounds, especially in the 18th and 19th centuries. It is at this point that rock materials, sometimes used as gemstones, impinge on the domain of typical heritage stones. In Australia, the gemstone most identifiable with the country is precious opal formed by sedimentary processes in the Great Artesian Basin. In this paper the question is asked whether "Australian Precious Opal" could be or should be considered as a heritage stone of international significance. Immediately Australian Precious Opal satisfies several GHSR criteria including historic use for more than 50 years and wide-ranging utilisation for prestige jewellery around the world. It is also recognised as a cultural icon including association with national identity in Australia as it is legally defined as Australia's "National Gemstone" as well as being the "Gemstone Emblem" for the State of South Australia. Opal continues to be mined. Designation of Australian Precious Opal as a Global Heritage Stone Resource would likely involve formal international recognition of Australian opal in the geological arena for the first time. Arguments against the international designation of opal may be that the GHSR designation was meant primarily for building stone, not gemstones, even if it is possible to purchase tiles with embedded opal material. It may be argued that opal is also a mineral not a stone or rock however the precious quality of opal results from mineral impurities/ crystal irregularities and specimens of boulder Opal are best regarded as rock. The decision on this matter is best based on whether designating precious opal will beneficially facilitate increased professional, community, national and international awareness of opal especially through scientific investigation, whilst also assisting marketing of opal as a commercial commodity. In addition, the real benefit of grouping opal in a designation that includes building stone needs to be considered? It is likely that not all gemstones could beneficially be designated a heritage stone because the level of manufacturing or processing may be so great that most natural qualities of the material are lost. In addition, Australian opal should most likely be beneficially recognised in an "Australian Precious Opal Province" given the extent of regional opal variation in Australia coupled with the unusual sedimentary aspect of most occurrences.

Cystoman® and calculi: a good alternative to standard therapies in preventing stone recurrence.

PubMed

Proietti, S; Giannantoni, A; Luciani, L G; Sortino, G; Graziotti, P; Giusti, G

2014-08-01

To assess the efficacy and tolerability of D-mannose-containing product (Cystoman(®)) in preventing recurrence in patients who underwent surgical treatment for infection related urinary stones. From January 2011 to February 2013 we have enrolled all consecutive patients affected by staghorn calculi and recurrent urinary tract infections (UTIs). All patients recommended for surgery were scheduled for percutaneous nephrolithotomy. The study agent was administered daily for 5 months after surgical procedure. At baseline and 5-month follow-up all patients underwent abdominal Computed Tomography (CT) scan and they also completed Medical Outcomes Study short-form, 36-item questionnaire (SF-36). They performed urine and urine culture monthly. The primary endpoints were the assessment of the efficacy with regard to infection-related urinary stone recurrence and the tolerability of Cystoman(®). The secondary endpoint was the evaluation of quality-of-life symptoms. During the study period, a total of 27 patients were included in the study. The data from 25 patients were analyzable. Seventeen patients (68%) did not report UTIs during follow-up. Eight patients (32%) remained infected and the average number of UTIs was 2.6 ± 1.6 in 5 months. At 5-month follow-up 17 (68%) patients were free from stones recurrence; in 8 (32%) cases CT scan revealed stone recurrence with an average stone diameter of 1.1 ± 0.4 cm. In nonrecurring patients, 2 (11.7%) reported an average of 1.5 ± 0.7 UTIs episodes; in recurring patients, 6 (75%) showed 3 ± 1.67 of UTIs episodes. Statistically significant differences were seen in the occurrence of UTIs episodes were detected between nonrecurring stone patients and recurring patients (p < 0.05). Moreover, statistically significant changes were detected in SF-36 scores from baseline to month 5 in the categories of physical functioning and energy/fatigue (p < 0.05). Cystoman(®) is effective in preventing infection-related urinary stones.

Jet Mixing in Direct-Chill Casting of Aluminum: Crater Effects and its Consequence on Centerline Segregation

NASA Astrophysics Data System (ADS)

Wagstaff, Samuel R.; Allanore, Antoine

2017-08-01

Recent reports have demonstrated the possibility of mitigating macrosegregation during the Direct-Chill casting of rolling slab ingots using an impinging jet. Herein, an analytical model is presented to predict the shape of the crater formed due to the impact of the jet on the slurry region. The model takes into account alloy composition, physical dimension, and casting speed on the distribution of forces and crater shape. The calculated shape of the crater profile is used to explain the centerline depletion in the impingement region previously reported.

"Black art" of thin film coating: why this term is used and how to change this mind-set

NASA Astrophysics Data System (ADS)

Jansen, S. W.; Hatchett, Philip J.; Hughes, S. W.; Jones, D. Paul; Gibson, Desmond R.

1996-08-01

The words 'black art' are often associated with thin film coating. We cast our spell on a coating plant and, as if by magic, the glass is transformed. The problem is that the spell sometimes fails and we end up with stone instead of gold. When we ask the magician (coating technician) what went wrong, the answer is all too often 'I did it exactly the same way as the last time'. This creates the perception that thin film coating is a black art because clearly something different did happen. What we don't know is which of the multitude of parameters went wrong, and often the only way to find out is through a process of elimination. This is very costly to the industry both in monetary value and image.

Hyaluronan and Stone Disease

NASA Astrophysics Data System (ADS)

Asselman, Marino

2008-09-01

Kidney stones cannot be formed as long as crystals are passed in the urine. However, when crystals are retained it becomes possible for them to aggregate and form a stone. Crystals are expected to be formed not earlier than the distal tubules and collecting ducts. Studies both in vitro and in vivo demonstrate that calcium oxalate monohydrate crystals do not adhere to intact distal epithelium, but only when the epithelium is proliferating or regenerating, so that it possesses dedifferentiated cells expressing hyaluronan, osteopontin (OPN) and their mutual receptor CD44 at the apical cell membrane. The polysaccharide hyaluronan is an excellent crystal binding molecule because of its negative ionic charge. We hypothesized that the risk for crystal retention in the human kidney would be increased when tubular cells express hyaluronan at their apical cell membrane. Two different patient categories in which nephrocalcinosis frequently occurs were studied to test this hypothesis (preterm neonates and kidney transplant patients). Hyaluronan (and OPN) expression at the luminal membrane of tubular cells indeed was observed, which preceded subsequent retention of crystals in the distal tubules. Tubular nephrocalcinosis has been reported to be associated with decline of renal function and thus further studies to extend our knowledge of the mechanisms of retention and accumulation of crystals in the kidney are warranted. Ultimately, this may allow the design of new strategies for the prevention and treatment of both nephrocalcinosis and nephrolithiasis in patients.

Hookahs

MedlinePlus

... Exposure is High in Multiunit Housing Smokeless Products Electronic Cigarettes Youth Tobacco Prevention Tobacco Products Tobacco Ingredient ... from 22% to 40%. 5 New forms of electronic hookah smoking, including steam stones and hookah pens, ...

Comparative Accuracy of Facial Models Fabricated Using Traditional and 3D Imaging Techniques.

PubMed

Lincoln, Ketu P; Sun, Albert Y T; Prihoda, Thomas J; Sutton, Alan J

2016-04-01

The purpose of this investigation was to compare the accuracy of facial models fabricated using facial moulage impression methods to the three-dimensional printed (3DP) fabrication methods using soft tissue images obtained from cone beam computed tomography (CBCT) and 3D stereophotogrammetry (3D-SPG) scans. A reference phantom model was fabricated using a 3D-SPG image of a human control form with ten fiducial markers placed on common anthropometric landmarks. This image was converted into the investigation control phantom model (CPM) using 3DP methods. The CPM was attached to a camera tripod for ease of image capture. Three CBCT and three 3D-SPG images of the CPM were captured. The DICOM and STL files from the three 3dMD and three CBCT were imported to the 3DP, and six testing models were made. Reversible hydrocolloid and dental stone were used to make three facial moulages of the CPM, and the impressions/casts were poured in type IV gypsum dental stone. A coordinate measuring machine (CMM) was used to measure the distances between each of the ten fiducial markers. Each measurement was made using one point as a static reference to the other nine points. The same measuring procedures were accomplished on all specimens. All measurements were compared between specimens and the control. The data were analyzed using ANOVA and Tukey pairwise comparison of the raters, methods, and fiducial markers. The ANOVA multiple comparisons showed significant difference among the three methods (p < 0.05). Further, the interaction of methods versus fiducial markers also showed significant difference (p < 0.05). The CBCT and facial moulage method showed the greatest accuracy. 3DP models fabricated using 3D-SPG showed statistical difference in comparison to the models fabricated using the traditional method of facial moulage and 3DP models fabricated from CBCT imaging. 3DP models fabricated using 3D-SPG were less accurate than the CPM and models fabricated using facial moulage and CBCT imaging techniques. © 2015 by the American College of Prosthodontists.

Formation of intermetallic compound coating on magnesium AZ91 cast alloy

NASA Astrophysics Data System (ADS)

Zhu, Tianping; Gao, Wei

2009-08-01

This study describes an intermetallic compound coating formed on AZ91 Mg cast alloy. The Al sputtered on AZ91 cast alloy reacted with substrate during a short period of heat treatment at 435°C, resulting in the formation of a continuous intermetallic compound layer. The short period treatment has the advantage of minimizing the negative effect on the microstructure of substrate and the mechanical properties, comparing with the reported diffusion coatings. DSC measurement and examination on the cross-section of Al sputtered samples show that local melting occurred along the Al/substrate interface at the temperature range between 430~435°C. The formation mechanism of intermetallic compound coating is proposed in terms of the local melting at Al/substrate interface. The salt water immersion test showed significant improvement in corrosion resistance of the intermetallic compound coated AZ91 cast alloy compared with the as-cast alloys.

Upgrade Recycling of Cast Iron Scrap Chips towards β-FeSi₂ Thermoelectric Materials.

PubMed

Laila, Assayidatul; Nanko, Makoto; Takeda, Masatoshi

2014-09-04

The upgrade recycling of cast-iron scrap chips towards β-FeSi₂ thermoelectric materials is proposed as an eco-friendly and cost-effective production process. By using scrap waste from the machining process of cast-iron components, the material cost to fabricate β-FeSi₂ is reduced and the industrial waste is recycled. In this study, β-FeSi₂ specimens obtained from cast iron scrap chips were prepared both in the undoped form and doped with Al and Co elements. The maximum figure of merit ( ZT ) indicated a thermoelectric performance of approximately 70% in p-type samples and nearly 90% in n-type samples compared to β-FeSi₂ prepared from pure Fe and other published studies. The use of cast iron scrap chips to produce β-FeSi₂ shows promise as an eco-friendly and cost-effective production process for thermoelectric materials.

Management of obstructive calcular anuria with acute renal failure in children less than 4 years in age: a protocol for initial urinary drainage in relation to planned definitive stone management.

PubMed

ElSheemy, Mohammed S; Shoukry, Ahmed I; Shouman, Ahmed M; ElShenoufy, Ahmed; Aboulela, Waseem; Daw, Kareem; Hussein, Ahmed A; Morsi, Hany A

2014-12-01

To describe and evaluate our protocol for management of children≤4years old with obstructive calcular anuria (OCA) and acute renal failure (ARF) to improve selection of initial urinary drainage (ID) method and to facilitate subsequent definitive stone management (DSM) as studies discussing this special group of patients are still few. Patients with a contraindication to any method of ID were excluded. Decision (percutaneous nephrostomy (PCN) or double J (JJ) stent) was based on degree of hydronephrosis and planned DSM. We used 4.8-5Fr JJ or 6-8Fr PCN under general anesthesia and fluoroscopic guidance. According to our protocol, JJ is inserted for hydronephrosis≤grade 1. When the hydronephrosis is >grade 1, patients with radiolucent stones were treated by JJ whatever the site of the stone. When the stones were radiopaque, PCN was reserved for stones in a solitary functioning kidney and bilateral ureteric stones prepared for subsequent bilateral ureterolithotomy (or stone prepared for ureterolithotomy in a solitary kidney). After normalization of renal functions, DSM was staged attacking only one side before discharge. Both sides were cleared at the same session in cases with bilateral ureterolithotomy. Renal or ureteric stones suitable for SWL in a solitary kidney were treated with percutaneous nephrolithotripsy (PNL) or ureteroscopy. This was followed also in patients with bilateral stones suitable for SWL by clearing one side using ureteroscopy or PNL before discharge. Open surgery (OS) was reserved for cases with failed ureteroscopy or PNL, for ureteric stones>2.5 cm in size or very large volume complex renal stones. Stone free rate (SFR) was evaluated by CT. Our protocol was evaluated as regard recovery of renal functions, complications, and number of interventions to clear stones. This study included 62 boys and 22 girls presented with anuria for 1-4 days. JJ and PCN were inserted in 105 and 30 ureterorenal units (URU), respectively. Creatinine returns normal within 72 h. JJ insertion formed a part of DSM in 78/159 (49%) URU (stones prepared for extracorporeal shockwave lithotripsy or oral chemolytic dissolution therapy). PCN was the ideal tract for subsequent PNL in 11/159 (6.9%) URU. Accordingly, ID participated by 55.97% in DSM. Both operative and imaging times were slightly longer with PCN than JJ. There was no statistically significant difference in the insertion success or mean period to return to normal chemistry. Complications of both methods were mild and without any significant difference. Endourologic procedures constituted the majority of our interventions. Open surgical and endoscopic interventions for clearance of stones (including ID, treatment conversion and 2ry procedures) were done once for 25 patients, twice for 43 patients while it was needed three times for 16 patients. Total number of interventions was 149 procedures. SFR was 94%. Our protocol ensures adequate ID with minimal complications when using our selection criteria in children≤4 years in age with OCA and ARF. It also minimizes number of subsequent procedures to clear stones. Complications and success in insertion and drainage were equivalent in PCN and JJ groups. Copyright © 2014 Journal of Pediatric Urology Company. Published by Elsevier Ltd. All rights reserved.

The Design of 3D-Printed Lattice-Reinforced Thickness-Varying Shell Molds for Castings.

PubMed

Shangguan, Haolong; Kang, Jinwu; Yi, Jihao; Zhang, Xiaochuan; Wang, Xiang; Wang, Haibin; Huang, Tao

2018-03-30

3D printing technologies have been used gradually for the fabrication of sand molds and cores for castings, even though these molds and cores are dense structures. In this paper, a generation method for lattice-reinforced thickness-varying shell molds is proposed and presented. The first step is the discretization of the STL (Stereo Lithography) model of a casting into finite difference meshes. After this, a shell is formed by surrounding the casting with varying thickness, which is roughly proportional to the surface temperature distribution of the casting that is acquired by virtually cooling it in the environment. A regular lattice is subsequently constructed to support the shell. The outside surface of the shell and lattice in the cubic mesh format is then converted to STL format to serve as the external surface of the new shell mold. The internal surface of the new mold is the casting's surface with the normals of all of the triangles in STL format reversed. Experimental verification was performed on an Al alloy wheel hub casting. Its lattice-reinforced thickness-varying shell mold was generated by the proposed method and fabricated by the binder jetting 3D printing. The poured wheel hub casting was sound and of good surface smoothness. The cooling rate of the wheel hub casting was greatly increased due to the shell mold structure. This lattice-reinforced thickness-varying shell mold generation method is of great significance for mold design for castings to achieve cooling control.

Genetic affinity between diverse ethnoreligious communities of Tamil Nadu, India: a microsatellite study.

PubMed

Eaaswarkhanth, M; Vasulu, T S; Haque, Ikramul

2008-12-01

Historically, a number of local Hindu caste groups have converted to Islam and formed religious endogamous groups. Therefore the local caste groups and religious communities in a region are expected to show genetic relatedness. In this study we investigate the genetic relationship between Tamil-speaking (Dravidian language) Muslims (Sunni), six endogamous Hindu castes, and a tribal ethnic group (Irulars) using 13 CODIS (Combined DNA Index System) autosomal microsatellite markers. Muslims show the highest average heterozygosity (0.405) compared to the other groups. The neighbor-joining tree and the multidimensional-scaling plot show clustering of Tamil-speaking Muslims with three caste groups (Gounder, Paraiyar, and Vanniyar), whereas the Irular tribe is separated out of the cluster.

PROTECTIVELY COVERED ARTICLE AND METHOD OF MANUFACTURE

DOEpatents

Plott, R.F.

1958-10-28

A method of casting a protective jacket about a ura nium fuel element that will bond completely to the uranium without the use of stringers or supports that would ordinarily produce gaps in the cast metal coating and bond is presented. Preformed endcaps of alumlnum alloyed with 13% silicon are placed on the ends of the uranium fuel element. These caps will support the fuel element when placed in a mold. The mold is kept at a ing alloy but below that of uranium so the cast metal jacket will fuse with the endcaps forming a complete covering and bond to the fuel element, which would otherwise oxidize at the gaps or discontinuities lefi in the coating by previous casting methods.

Insights into early lithic technologies from ethnography.

PubMed

Hayden, Brian

2015-11-19

Oldowan lithic assemblages are often portrayed as a product of the need to obtain sharp flakes for cutting into animal carcases. However, ethnographic and experimental research indicates that the optimal way to produce flakes for such butchering purposes is via bipolar reduction of small cryptocrystalline pebbles rather than from larger crystalline cores resembling choppers. Ethnographic observations of stone tool-using hunter-gatherers in environments comparable with early hominins indicate that most stone tools (particularly chopper forms and flake tools) were used for making simple shaft tools including spears, digging sticks and throwing sticks. These tools bear strong resemblances to Oldowan stone tools. Bipolar reduction for butchering probably preceded chopper-like core reduction and provides a key link between primate nut-cracking technologies and the emergence of more sophisticated lithic technologies leading to the Oldowan. © 2015 The Author(s).

An Additional Potential Factor for Kidney Stone Formation during Space Flights: Calcifying Nanoparticles (Nanobacteria): A Case Report

NASA Technical Reports Server (NTRS)

Jones, Jeffrey A.; Ciftcioglu, Neva; Schmid, Joseph; Griffith, Donald

2007-01-01

Spaceflight-induced microgravity appears to be a risk factor for the development of urinary calculi due to skeletal calcium liberation and other undefined factors, resulting in stone disease in crewmembers during and after spaceflight. Calcifying nanoparticles, or nanobacteria, reproduce at a more rapid rate in simulated microgravity conditions and create external shells of calcium phosphate in the form of apatite. The questions arises whether calcifying nanoparticles are niduses for calculi and contribute to the development of clinical stone disease in humans, who possess environmental factors predisposing to the development of urinary calculi and potentially impaired immunological defenses during spaceflight. A case of a urinary calculus passed from an astronaut post-flight with morphological characteristics of calcifying nanoparticles and staining positive for a calcifying nanoparticle unique antigen, is presented.

Complete Occlusion of a Subcutaneous Pyelovesical Bypass Graft (Detour® System) Caused by Uric Acid Stone Formation.

PubMed

Wilhelm, Konrad; Schultze-Seemann, Wolfgang; Miernik, Arkadiusz

2017-01-01

Subcutaneous pyelovesical bypass graft (SPBG) is a urinary diversion treatment option for ureteral obstruction. Initially its use was limited to palliative care patients. However, the indication profile has been extended to selected patients with benign conditions causing ureteral obstruction and hydronephrosis. Occlusion of SPBGs is rarely reported and mostly related to infections. We describe the clinical case of a patient with SPBG after iatrogenic ureteral stricture who was not suitable for other reconstructive treatment forms due to distinct retroperitoneal scarring after multiple previous surgeries. Several months after the SPBG insertion, the patient developed complete occlusion of the system with uric acid stone material. Sufficient endoscopic intervention was not feasible. After forced chemolitholysis, the stone mass could be completely dissolved. Since then the patient has remained symptom-free. © 2014 S. Karger AG, Basel.

Recent finding and new technologies in nephrolitiasis: a review of the recent literature

PubMed Central

2013-01-01

This review summarizes recent literature on advances regarding renal and ureteral calculi, with particular focus in areas of recent advances in the overall field of urolithiasis. Clinical management in everyday practice requires a complete understanding of the issues regarding metabolic evaluation and subgrouping of stone-forming patients, diagnostic procedures, effective treatment regime in acute stone colic, medical expulsive therapy, and active stone removal. In this review we focus on new perspectives in managing nephrolitihiasis and discuss recentadvances, including medical expulsive therapy, new technologies, and refinements of classical therapy such as shock wave lithotripsy, give a fundamental modification of nephrolithiasis management. Overall, this field appears to be the most promising, capable of new developments in ureterorenoscopy and percutaneous approaches. Further improvements are expected from robotic-assisted procedures, such as flexible robotics in ureterorenoscopy. PMID:23413950

Ultrasound Use in Urinary Stones: Adapting Old Technology for a Modern-Day Disease.

PubMed

Tzou, David T; Usawachintachit, Manint; Taguchi, Kazumi; Chi, Thomas

2017-04-01

Ultrasound has become a mainstay tool in urologists' armamentarium for the diagnosis and management of nephrolithiasis. From starting as a rudimentary form of imaging, it has come to play a more prominent role over time, paralleling evolution in ultrasound technology. Throughout the medical community there is a growing emphasis on reducing the amount of ionizing radiation delivered to patients during routine imaging. As such there has been a resurgence of interest in ultrasound given its lack of associated radiation exposure and proven effectiveness as a diagnostic and therapeutic imaging modality. Herein, we provide a review of the history of ultrasound, how the use of ultrasound is expanding in both diagnosis and treatment of urinary stone disease, and finally how promising applications of ultrasound are shaping the future of kidney stone management.

Ultrasound Use in Urinary Stones: Adapting Old Technology for a Modern-Day Disease

PubMed Central

Tzou, David T.; Usawachintachit, Manint; Taguchi, Kazumi

2017-01-01

Abstract Ultrasound has become a mainstay tool in urologists' armamentarium for the diagnosis and management of nephrolithiasis. From starting as a rudimentary form of imaging, it has come to play a more prominent role over time, paralleling evolution in ultrasound technology. Throughout the medical community there is a growing emphasis on reducing the amount of ionizing radiation delivered to patients during routine imaging. As such there has been a resurgence of interest in ultrasound given its lack of associated radiation exposure and proven effectiveness as a diagnostic and therapeutic imaging modality. Herein, we provide a review of the history of ultrasound, how the use of ultrasound is expanding in both diagnosis and treatment of urinary stone disease, and finally how promising applications of ultrasound are shaping the future of kidney stone management. PMID:27733052

The transduodenal per-ampullary approach to common bile duct calculi.

PubMed Central

Carter, A. E.

1983-01-01

A method of management of 212 patients whose common bile duct calculi were removed through the Ampulla of Vater across the duodenum is described. One patient died from haemorrhagic pancreatitis directly related to the procedure and 11 others died from causes related to the need for a major procedure in people relatively late in life: an overall mortality of 5.7% and of 0.5% for directly related causes. Ten patients suffered non-fatal complications. Ninety three left hospital within 14 days after operation and 79 within 21 days. Although one patient, for a special reason, continued to form stones and discharged them without any difficulty, no others have formed stones that have been recognised symptomatically or clinically. No patient has had cholangitis or common duct stenosis. PMID:6859782

Generation of strip-format fibrin-based engineered heart tissue (EHT).

PubMed

Schaaf, Sebastian; Eder, Alexandra; Vollert, Ingra; Stöhr, Andrea; Hansen, Arne; Eschenhagen, Thomas

2014-01-01

This protocol describes a method for casting fibrin-based engineered heart tissue (EHT) in standard 24-well culture dishes. In principle, a hydrogel tissue engineering method requires cardiomyocytes, a liquid matrix that forms a gel, a casting mold, and a device that keeps the developing tissue in place. This protocol refers to neonatal rat heart cells as the cell source; the matrix of choice is fibrin, and the tissues are generated in rectangular agarose-casting molds (12 × 3 × 3 mm) prepared in standard 24-well cell culture dishes, in which a pair of flexible silicone posts is suspended from above. A master mix of freshly isolated cells, medium, fibrinogen, and thrombin is pipetted into the casting mold and, over a period of 2 h, polymerizes and forms a fibrin cell block around two silicone posts. Silicone racks holding four pairs of silicone posts each are used to transfer the fresh fibrin cell blocks into new 24-well dishes with culture medium. Without further handling, the cells start to remodel the fibrin gel, form contacts with each other, elongate, and condense the gel to approximately ¼ of the initial volume. Spontaneous and rhythmic contractions start after 1 week. EHTs are viable and relatively stable for several weeks in this format and can be subjected to repeated measurements of contractile function and final morphological and molecular analyses.

Fine-scaled human genetic structure revealed by SNP microarrays.

PubMed

Xing, Jinchuan; Watkins, W Scott; Witherspoon, David J; Zhang, Yuhua; Guthery, Stephen L; Thara, Rangaswamy; Mowry, Bryan J; Bulayeva, Kazima; Weiss, Robert B; Jorde, Lynn B

2009-05-01

We report an analysis of more than 240,000 loci genotyped using the Affymetrix SNP microarray in 554 individuals from 27 worldwide populations in Africa, Asia, and Europe. To provide a more extensive and complete sampling of human genetic variation, we have included caste and tribal samples from two states in South India, Daghestanis from eastern Europe, and the Iban from Malaysia. Consistent with observations made by Charles Darwin, our results highlight shared variation among human populations and demonstrate that much genetic variation is geographically continuous. At the same time, principal components analyses reveal discernible genetic differentiation among almost all identified populations in our sample, and in most cases, individuals can be clearly assigned to defined populations on the basis of SNP genotypes. All individuals are accurately classified into continental groups using a model-based clustering algorithm, but between closely related populations, genetic and self-classifications conflict for some individuals. The 250K data permitted high-level resolution of genetic variation among Indian caste and tribal populations and between highland and lowland Daghestani populations. In particular, upper-caste individuals from Tamil Nadu and Andhra Pradesh form one defined group, lower-caste individuals from these two states form another, and the tribal Irula samples form a third. Our results emphasize the correlation of genetic and geographic distances and highlight other elements, including social factors that have contributed to population structure.

An Investigation of the Mold-Flux Performance for the Casting of Cr12MoV Steel Using a Mold Simulator Technique

NASA Astrophysics Data System (ADS)

Zhou, Lejun; Wang, Wanlin; Xu, Chao; Zhang, Chen

2017-08-01

Mold flux plays important roles in the process of continuous casting. In this article, the performance of mold flux for the casting of Cr12MoV steel was investigated by using a mold simulator. The results showed that the slag film formed in the gap between the initial shell and mold hot surface is thin and discontinuous during the casting process with the Flux BM, due to the absorption of chromic oxide inclusions into the liquid slag, while the slag film formed in the case of the optimized Flux NEW casting process is uniform. The main precipitated crystals in Flux BM slag film are cuspidine (Ca4Si2O7F2) and Cr3O4, but only Ca4Si2O7F2 precipitated in the Flux NEW case. Besides, both the responding temperature and heat flux in the case of Flux BM are relatively higher and fluctuate in a larger amplitude. The surface of the shell obtained in the case of the Flux BM experiment is quite uneven, and many severe depressions, cracks, and entrapped slags are observed in the surface due to the lack of lubrication. However, the obtained shell surface in the case of the Flux NEW shows good surface quality due to the addition of B2O3 and the adjustment of basicity, which can compensate for the negative effects of the mold-flux properties caused by the absorption of chromic oxide during the casting process.

A combined arc-melting and tilt-casting furnace for the manufacture of high-purity bulk metallic glass materials.

PubMed

Soinila, E; Pihlajamäki, T; Bossuyt, S; Hänninen, H

2011-07-01

An arc-melting furnace which includes a tilt-casting facility was designed and built, for the purpose of producing bulk metallic glass specimens. Tilt-casting was chosen because reportedly, in combination with high-purity processing, it produces the best fatigue endurance in Zr-based bulk metallic glasses. Incorporating the alloying and casting facilities in a single piece of equipment reduces the amount of laboratory space and capital investment needed. Eliminating the sample transfer step from the production process also saves time and reduces sample contamination. This is important because the glass forming ability in many alloy systems, such as Zr-based glass-forming alloys, deteriorates rapidly with increasing oxygen content of the specimen. The challenge was to create a versatile instrument, in which high purity conditions can be maintained throughout the process, even when melting alloys with high affinity for oxygen. Therefore, the design provides a high-vacuum chamber to be filled with a low-oxygen inert atmosphere, and takes special care to keep the system hermetically sealed throughout the process. In particular, movements of the arc-melting electrode and sample manipulator arm are accommodated by deformable metal bellows, rather than sliding O-ring seals, and the whole furnace is tilted for tilt-casting. This performance of the furnace is demonstrated by alloying and casting Zr(55)Cu(30)Al(10)Ni(5) directly into rods up to ø 10 mm which are verified to be amorphous by x-ray diffraction and differential scanning calorimetry, and to exhibit locally ductile fracture at liquid nitrogen temperature.

Earth Observations taken by the Expedition 17 Crew

NASA Image and Video Library

2008-05-30

ISS017-E-008285 (30 May 2008) --- Pyramids of Dashur, Egypt are featured in this image photographed by an Expedition 17 crewmember on the International Space Station. While the pyramids of Giza are perhaps the most famous, there are several other ancient Egyptian royal necropolis ("city of the dead") sites situated along the Nile River and its delta. One of these sites is located near the village of Dashur (upper right). The gray-brown built area of Dashur is surrounded by green agricultural land of the Nile Delta, which forms a distinct boundary with the tan desert to the west. It is in the desert that the monuments of the ancient rulers of Egypt are found. Several monuments are visible in this image, including the large Red and Bent Pyramids built by Snofru, first king of the 4th Dynasty that lasted from 2575-2465 BC. Other visible monuments include the pyramid complexes of Amenemhat III and Sesostris III, both kings of the 12th Dynasty (1991-1783 BC). Both of these complexes are poorly preserved, due both to unstable ground conditions, and dismantling of the limestone blocks forming the outer pyramid casings during later historical periods. The Bent Pyramid (lower right) is so called as the slope of the outer face was lessened halfway through construction, leading to a distinctive "bent" profile -- explanations for why this was done include decreasing the mass of the pyramid to prevent collapse, or to reduce the work necessary to complete it. The Red Pyramid to the north (center) was built after the Bent Pyramid, and is named for the coloration of the building stone at the structure's core. An irregular dark feature to the southeast of the Bent Pyramid is not a shadow cast by a monument; it is an irrigation feature extending into the desert.

Bond and fracture strength of metal-ceramic restorations formed by selective laser sintering

PubMed Central

Bae, Eun-Jeong; Kim, Woong-Chul; Kim, Hae-Young

2014-01-01

PURPOSE The purpose of this study was to compare the fracture strength of the metal and the bond strength in metal-ceramic restorations produced by selective laser sintering (SLS) and by conventional casting (CAST). MATERIALS AND METHODS Non-precious alloy (StarLoy C, DeguDent, Hanau, Germany) was used in CAST group and metal powder (SP2, EOS GmbH, Munich, Germany) in SLS group. Metal specimens in the form of sheets (25.0 × 3.0 × 0.5 mm) were produced in accordance with ISO 9693:1999 standards (n=30). To measure the bond strength, ceramic was fired on a metal specimen and then three-point bending test was performed. In addition, the metal fracture strength was measured by continuing the application of the load. The values were statistically analyzed by performing independent t-tests (α=.05). RESULTS The mean bond strength of the SLS group (50.60 MPa) was higher than that of the CAST group (46.29 MPa), but there was no statistically significant difference. The metal fracture strength of the SLS group (1087.2 MPa) was lower than that of the CAST group (2399.1 MPa), and this difference was statistically significant. CONCLUSION In conclusion the balling phenomenon and the gap formation of the SLS process may increase the metal-ceramic bond strength. PMID:25177469

Non-graphite crucible for high temperature applications

DOEpatents

Holcombe, Cressie E.; Pfeiler, William A.

1996-01-01

A multi-piece crucible for high temperature applications comprises a tubular side wall member having a lip on the inside surface and a bottom member or members forming a container for containing a melt of a material during a high temperature melt-casting operations. The multi-piece design prevents cracking of the crucible or leakage of the melt from the crucible during the melt-casting operation. The lip of the tubular member supports the bottom member. The contacting surfaces where the lip of the tubular side wall member contacts the bottom member of the multi-piece crucible contains a ceramic sealing material. The ceramic sealing material forms a seal sufficient to prevent the melt of the material from leaking out of the multi-piece crucible during the melt-casting process. The multi-piece crucible is made of a material which is chemically inert to the melt and has structural integrity at the melting point temperature of the melt, or of a material coated with such a material. The multi-piece crucible is contained in a thermal can assembly of a high temperature induction furnace during a high temperature melt-casting operation. One embodiment of the multi-piece crucible comprises a tubular member having a vertical slot filled with a ceramic sealing material to provide expansion of the tubular member without cracking during the high temperature melt-casting operation.

Non-graphite crucible for high temperature applications

DOEpatents

Holcombe, C.E.; Pfeiler, W.A.

1996-01-09

A multi-piece crucible for high temperature applications comprises a tubular side wall member having a lip on the inside surface and a bottom member or members forming a container for containing a melt of a material during a high temperature melt-casting operations. The multi-piece design prevents cracking of the crucible or leakage of the melt from the crucible during the melt-casting operation. The lip of the tubular member supports the bottom member. The contacting surfaces where the lip of the tubular side wall member contacts the bottom member of the multi-piece crucible contains a ceramic sealing material. The ceramic sealing material forms a seal sufficient to prevent the melt of the material from leaking out of the multi-piece crucible during the melt-casting process. The multi-piece crucible is made of a material which is chemically inert to the melt and has structural integrity at the melting point temperature of the melt, or of a material coated with such a material. The multi-piece crucible is contained in a thermal can assembly of a high temperature induction furnace during a high temperature melt-casting operation. One embodiment of the multi-piece crucible comprises a tubular member having a vertical slot filled with a ceramic sealing material to provide expansion of the tubular member without cracking during the high temperature melt-casting operation. 9 figs.

Penicillamine

MedlinePlus

... in combination with other treatments to treat severe rheumatoid arthritis (a condition in which the body's immune system ... up and forming stones. It works to treat rheumatoid arthritis by decreasing some actions of the immune system.

Effect of Soda Consumption on Urinary Stone Risk Parameters

PubMed Central

Holmes, Ross P.; Knight, John; Easter, Linda; Pais, Vernon; Assimos, Dean G.

2009-01-01

Abstract Background and Purpose Fluid consumption has been demonstrated to influence kidney stone formation. Studies have shown that consumption of cola may be a risk factor for stone disease, while fluids containing citric acid may attenuate stone activity. Diet was not always controlled in these investigations, however. We undertook a study to determine the impact of three different fluids on urinary stone risk factors. Subjects and Methods Six healthy nonstone-forming adults were placed on a standardized metabolic diet and consumed three different types of fluid during three 5-day periods. There was a 2-day washout between each sequence. The three fluids administered during these periods were Le Bleu® water, caffeine-free Diet Coke,® and Fresca® (citrate containing). These two soda preparations were chosen to prevent the known increase in calcium excretion promoted by carbohydrates and caffeine. Twenty-four hour urine specimens were collected on days 4 and 5 of each sequence. The following urinary parameters were measured: Volume, calcium, oxalate, creatinine, uric acid, citrate, sodium, magnesium, phosphorus, sulfate, urea nitrogen, pH, and supersaturation indices. A paired t test was used for statistical analysis. Results Urinary volumes were significantly higher and supersaturation of calcium oxalate significantly lower compared with a self-selected dietary regimen. A decrease in uric acid was also seen in the Fresca cohort. There were no statistically significant differences for any of the urinary parameters. Conclusion There is no increased risk or benefit to consuming Fresca or caffeine-free Diet Coke compared with Le Bleu bottled water with respect to stone formation. PMID:19275488

Stone tools from the ancient Tongan state reveal prehistoric interaction centers in the Central Pacific

PubMed Central

Clark, Geoffrey R.; Reepmeyer, Christian; Melekiola, Nivaleti; Woodhead, Jon; Dickinson, William R.; Martinsson-Wallin, Helene

2014-01-01

Tonga was unique in the prehistoric Pacific for developing a maritime state that integrated the archipelago under a centralized authority and for undertaking long-distance economic and political exchanges in the second millennium A.D. To establish the extent of Tonga’s maritime polity, we geochemically analyzed stone tools excavated from the central places of the ruling paramounts, particularly lithic artifacts associated with stone-faced chiefly tombs. The lithic networks of the Tongan state focused on Samoa and Fiji, with one adze sourced to the Society Islands 2,500 km from Tongatapu. To test the hypothesis that nonlocal lithics were especially valued by Tongan elites and were an important source of political capital, we analyzed prestate lithics from Tongatapu and stone artifacts from Samoa. In the Tongan state, 66% of worked stone tools were long-distance imports, indicating that interarchipelago connections intensified with the development of the Tongan polity after A.D. 1200. In contrast, stone tools found in Samoa were from local sources, including tools associated with a monumental structure contemporary with the Tongan state. Network analysis of lithics entering the Tongan state and of the distribution of Samoan adzes in the Pacific identified a centralized polity and the products of specialized lithic workshops, respectively. These results indicate that a significant consequence of social complexity was the establishment of new types of specialized sites in distant geographic areas. Specialized sites were loci of long-distance interaction and formed important centers for the transmission of information, people, and materials in prehistoric Oceania. PMID:25002481

The age of the hominin fossils from Jebel Irhoud, Morocco, and the origins of the Middle Stone Age.

PubMed

Richter, Daniel; Grün, Rainer; Joannes-Boyau, Renaud; Steele, Teresa E; Amani, Fethi; Rué, Mathieu; Fernandes, Paul; Raynal, Jean-Paul; Geraads, Denis; Ben-Ncer, Abdelouahed; Hublin, Jean-Jacques; McPherron, Shannon P

2017-06-07

The timing and location of the emergence of our species and of associated behavioural changes are crucial for our understanding of human evolution. The earliest fossil attributed to a modern form of Homo sapiens comes from eastern Africa and is approximately 195 thousand years old, therefore the emergence of modern human biology is commonly placed at around 200 thousand years ago. The earliest Middle Stone Age assemblages come from eastern and southern Africa but date much earlier. Here we report the ages, determined by thermoluminescence dating, of fire-heated flint artefacts obtained from new excavations at the Middle Stone Age site of Jebel Irhoud, Morocco, which are directly associated with newly discovered remains of H. sapiens. A weighted average age places these Middle Stone Age artefacts and fossils at 315 ± 34 thousand years ago. Support is obtained through the recalculated uranium series with electron spin resonance date of 286 ± 32 thousand years ago for a tooth from the Irhoud 3 hominin mandible. These ages are also consistent with the faunal and microfaunal assemblages and almost double the previous age estimates for the lower part of the deposits. The north African site of Jebel Irhoud contains one of the earliest directly dated Middle Stone Age assemblages, and its associated human remains are the oldest reported for H. sapiens. The emergence of our species and of the Middle Stone Age appear to be close in time, and these data suggest a larger scale, potentially pan-African, origin for both.

Stone tools from the ancient Tongan state reveal prehistoric interaction centers in the Central Pacific

NASA Astrophysics Data System (ADS)

Clark, Geoffrey R.; Reepmeyer, Christian; Melekiola, Nivaleti; Woodhead, Jon; Dickinson, William R.; Martinsson-Wallin, Helene

2014-07-01

Tonga was unique in the prehistoric Pacific for developing a maritime state that integrated the archipelago under a centralized authority and for undertaking long-distance economic and political exchanges in the second millennium A.D. To establish the extent of Tonga's maritime polity, we geochemically analyzed stone tools excavated from the central places of the ruling paramounts, particularly lithic artifacts associated with stone-faced chiefly tombs. The lithic networks of the Tongan state focused on Samoa and Fiji, with one adze sourced to the Society Islands 2,500 km from Tongatapu. To test the hypothesis that nonlocal lithics were especially valued by Tongan elites and were an important source of political capital, we analyzed prestate lithics from Tongatapu and stone artifacts from Samoa. In the Tongan state, 66% of worked stone tools were long-distance imports, indicating that interarchipelago connections intensified with the development of the Tongan polity after A.D. 1200. In contrast, stone tools found in Samoa were from local sources, including tools associated with a monumental structure contemporary with the Tongan state. Network analysis of lithics entering the Tongan state and of the distribution of Samoan adzes in the Pacific identified a centralized polity and the products of specialized lithic workshops, respectively. These results indicate that a significant consequence of social complexity was the establishment of new types of specialized sites in distant geographic areas. Specialized sites were loci of long-distance interaction and formed important centers for the transmission of information, people, and materials in prehistoric Oceania.

Clinical use of patient decision-making aids for stone patients.

PubMed

Lim, Amy H; Streeper, Necole M; Best, Sara L; Penniston, Kristina L; Nakada, Stephen Y

2017-08-01

Patient decision-making aids (PDMAs) help patients make informed healthcare decisions and improve patient satisfaction. The utility of PDMAs for patients considering treatments for urolithiasis has not yet been published. We report our experience using PDMAs developed at our institution in the outpatient clinical setting in patients considering a variety of treatment options for stones. Patients with radiographically confirmed urolithiasis were given PDMAs regarding treatment options for their stone(s) based on their clinical profile. We assessed patients' satisfaction, involvedness, and feeling of making a more informed decision with utilization of the PDMAs using a Likert Scale Questionnaire. Information was also collected regarding previous stone passage, history and type of surgical intervention for urolithiasis, and level of education. Patients (n = 43; 18 males, 23 females and two unknown) 53 +/- 14years old were included. Patients reported that they understood the advantages and disadvantages outlined in the PDMAs (97%), that the PDMAs helped them make a more informed decision (83%) and felt more involved in the decision making process (88%). Patients reported that the aids were presented in a balanced manner and used up-to-date scientific information (100%, 84% respectively). Finally, a majority of the patients prefer an expert's opinion when making a treatment decision (98%) with 73% of patients preferring to form their own opinion based on available information. Previous stone surgery was associated with patients feeling more involved with the decision making process (p = 0.0465). PDMAs have a promising role in shared decision-making in the setting of treatment options for nephrolithiasis.

TiC-Fe-Based Composite Coating Prepared by Self-Propagating High-Temperature Synthesis

NASA Astrophysics Data System (ADS)

He, Shen; Fan, Xi'an; Chang, Qingming; Xiao, Lixiang

2017-06-01

TiC-Fe-based composite coatings were prepared in situ by self-propagating high-temperature synthesis combined with vacuum expendable pattern casting process. The band-like TiC phase embedded in a continuous Fe binder. There were no obvious defects and impurities at the interface between coatings and matrices. Fe presented consecutively in the coating zones and substrate zones without interruption and the microhardness in the cross-sectional area of the coating-matrix reduces continuously from the coating to the matrix area, indicating a good metallurgical bonding between the coatings and matrices. The effect of casting temperature on the microstructure and hardness of TiC-Fe-based composite coating was investigated in detail. The TiC particles formed at low casting temperature were nearly spherical in shape, and the size of TiC particles increased with increasing casting temperature due to more agglomeration. The hardness of the coatings increased first and then decreased with increasing casting temperature, and reached the highest value of 68 HRC when the casting temperature was 1773 K (1500 °C), which was twice more than that of the matrix.

Three-dimensional biometric study of palatine rugae in children with a mixed-model analysis: a 9-year longitudinal study.

PubMed

Kim, Hong-Kyun; Moon, Sung-Chul; Lee, Shin-Jae; Park, Young-Seok

2012-05-01

The palatine rugae have been suggested as stable reference points for superimposing 3-dimensional virtual models before and after orthodontic treatment. We investigated 3-dimensional changes in the palatine rugae of children over 9 years. Complete dental stone casts were biennially prepared for 56 subjects (42 girls, 14 boys) aged from 6 to 14 years. Using 3-dimensional laser scanning and reconstruction software, virtual casts were constructed. Medial and lateral points of the first anterior 3 rugae were defined as the 3-dimensional landmarks. The length of each ruga and the distance between the end points of the rugae were measured in virtual 3-dimensional space. The measurement changes over time were analyzed by using the mixed-effect method for longitudinal data. There were slight increases in the linear measurements in the rugae areas: the lengths of the rugae and the distances between them during the observation period. However, the amounts of the increments were relatively small when compared with the initial values and individual random variability. Although age affected the linear dimensions significantly, it was not clinically significant; the rugae were relatively stable. The use of the palatine rugae as reference points for superimposing and evaluating changes during orthodontic treatment was thought to be possible with special cautions. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Substituting milk for apple juice does not increase kidney stone risk in most normocalciuric adults who form calcium oxalate stones.

PubMed

Massey, L K; Kynast-Gales, S A

1998-03-01

Increasing intake of dietary calcium from less than 400 mg to 800 mg daily may decrease the absorption of dietary oxalate, which in turn would decrease urinary oxalate excretion. The effect of substituting milk for apple juice on urine composition and risk of calcium oxalate precipitability was studied. Twenty-one normocalciuric adults with a history of at least 1 calcium oxalate stone and urinary oxalate excretion exceeding 275 micromol/day on their self-selected diet. Randomized crossover trial. Each participant consumed two moderate-oxalate (2,011 micromol/day) study diets, which were identical except that one contained 360 mL milk and the other contained 540 mL apple juice as the beverage with meals. Four days free-living then 2 days in the metabolic unit of a university nutrition department. Tiselius risk index for calcium oxalate precipitability calculated from urine composition. Paired t tests. Twenty-four hour urinary oxalate excretion was 18% lower (P<.0001) on the milk diet vs the juice diet: 423 vs 514 micromol, respectively. Calcium excretion was 17% higher (P<.05) on the milk vs juice diet: 4.7 vs 3.9 mmol, respectively. Urinary magnesium and citrate excretion, volume, and Tiselius risk index did not differ between diets. Substituting 360 mL milk daily for apple juice with meals in a diet containing moderate amounts of dietary oxalate from whole grains, legumes, fruits, and vegetables does not increase the risk index of calcium oxalate precipitability in most normocalciuric adults who form stones.

Method For Removing Volatile Components From A Gel-Cast Ceramic Article

DOEpatents

Klug, Frederic Joseph; DeCarr, Sylvia Marie

2004-09-07

A method of removing substantially all of the volatile component in a green, volatile-containing ceramic article is disclosed. The method comprises freezing the ceramic article; and then subjecting the frozen article to a vacuum for a sufficient time to freeze-dry the article. Frequently, the article is heated while being freeze-dried. Use of this method efficiently reduces the propensity for any warpage of the article. The article is often formed from a ceramic slurry in a gel-casting process. A method for fabricating a ceramic core used in investment casting is also described.

Nonaqueous slip casting of YBa2Cu3O(7-x) superconductive ceramics. Ph.D. Thesis - 1993

NASA Technical Reports Server (NTRS)

Hooker, Matthew W.; Taylor, Theodore D.

1994-01-01

This study investigates the slip casting of YBa2Cu3O(7-x) powders using nonaqueous carrier liquids and fired ceramic molds. The parameters of the process examined here include the rheological properties of YBa2Cu3O(7-x) powder dispersed in various solvent/dispersant systems, the combination of nonaqueous slips with fired ceramic molds to form the superconductive ceramics, the process-property relationships using a four-factor factorial experiment, and the applicability of magnetic fields to align the YBa2Cu3O(7-x) grains during the casting process.

Conservation of ornamental stone by Myxococcus xanthus-induced carbonate biomineralization.

PubMed

Rodriguez-Navarro, Carlos; Rodriguez-Gallego, Manuel; Ben Chekroun, Koutar; Gonzalez-Muñoz, Maria Teresa

2003-04-01

Increasing environmental pollution in urban areas has been endangering the survival of carbonate stones in monuments and statuary for many decades. Numerous conservation treatments have been applied for the protection and consolidation of these works of art. Most of them, however, either release dangerous gases during curing or show very little efficacy. Bacterially induced carbonate mineralization has been proposed as a novel and environmentally friendly strategy for the conservation of deteriorated ornamental stone. However, the method appeared to display insufficient consolidation and plugging of pores. Here we report that Myxococcus xanthus-induced calcium carbonate precipitation efficiently protects and consolidates porous ornamental limestone. The newly formed carbonate cements calcite grains by depositing on the walls of the pores without plugging them. Sonication tests demonstrate that these new carbonate crystals are strongly attached to the substratum, mostly due to epitaxial growth on preexisting calcite grains. The new crystals are more stress resistant than the calcite grains of the original stone because they are organic-inorganic composites. Variations in the phosphate concentrations of the culture medium lead to changes in local pH and bacterial productivity. These affect the structure of the new cement and the type of precipitated CaCO(3) polymorph (vaterite or calcite). The manipulation of culture medium composition creates new ways of controlling bacterial biomineralization that in the future could be applied to the conservation of ornamental stone.

Calcium carbonate crystals promote calcium oxalate crystallization by heterogeneous or epitaxial nucleation: possible involvement in the control of urinary lithogenesis.

PubMed

Geider, S; Dussol, B; Nitsche, S; Veesler, S; Berthézène, P; Dupuy, P; Astier, J P; Boistelle, R; Berland, Y; Dagorn, J C; Verdier, J M

1996-07-01

A large proportion of urinary stones have calcium oxalate (CaOx) as the major mineral phase. In these stones, CaOx is generally associated with minor amounts of other calcium salts. Several reports showing the presence of calcium carbonate (CaCO3) and calcium phosphate in renal stones suggested that crystals of those salts might be present in the early steps of stone formation. Such crystals might therefore promote CaOx crystallization from supersaturated urine by providing an appropriate substrate for heterogeneous nucleation. That possibility was investigated by seeding a metastable solution of 45Ca oxalate with vaterite or calcite crystallites. Accretion of CaOx was monitored by 45Ca incorporation. We showed that (1) seeds of vaterite (the hexagonal polymorph of CaCO3) and calcite (the rhomboedric form) could initiate calcium oxalate crystal growth; (2) in the presence of lithostathine, an inhibitor of CaCO3 crystal growth, such accretion was not observed. In addition, scanning electron microscopy demonstrated that growth occurred by epitaxy onto calcite seeds whereas no special orientation was observed onto vaterite. It was concluded that calcium carbonate crystals promote crystallization of calcium oxalate and that inhibitors controlling calcium carbonate crystal formation in Henle's loop might play an important role in the prevention of calcium oxalate stone formation.

Conservation of Ornamental Stone by Myxococcus xanthus-Induced Carbonate Biomineralization

PubMed Central

Rodriguez-Navarro, Carlos; Rodriguez-Gallego, Manuel; Ben Chekroun, Koutar; Gonzalez-Muñoz, Maria Teresa

2003-01-01

Increasing environmental pollution in urban areas has been endangering the survival of carbonate stones in monuments and statuary for many decades. Numerous conservation treatments have been applied for the protection and consolidation of these works of art. Most of them, however, either release dangerous gases during curing or show very little efficacy. Bacterially induced carbonate mineralization has been proposed as a novel and environmentally friendly strategy for the conservation of deteriorated ornamental stone. However, the method appeared to display insufficient consolidation and plugging of pores. Here we report that Myxococcus xanthus-induced calcium carbonate precipitation efficiently protects and consolidates porous ornamental limestone. The newly formed carbonate cements calcite grains by depositing on the walls of the pores without plugging them. Sonication tests demonstrate that these new carbonate crystals are strongly attached to the substratum, mostly due to epitaxial growth on preexisting calcite grains. The new crystals are more stress resistant than the calcite grains of the original stone because they are organic-inorganic composites. Variations in the phosphate concentrations of the culture medium lead to changes in local pH and bacterial productivity. These affect the structure of the new cement and the type of precipitated CaCO3 polymorph (vaterite or calcite). The manipulation of culture medium composition creates new ways of controlling bacterial biomineralization that in the future could be applied to the conservation of ornamental stone. PMID:12676699

[Confined blasting in microexplosion cystolithotripsy].

PubMed

Uchida, M

1989-03-01

This paper is the 12th report in a series of studies on the application of microexplosion to medicine and biology. Microexplosion lithotripsy is a newly developed technique in our clinic to crush urinary stones with small quantities of explosives. A systematic research project has been performed since the first report of microexplosion lithotripsy in 1977. As a result, microexplosion was successfully applied to the destruction of bladder stones in 130 cases from 1981 to 1988. In blasting to crush rocks in industrial works, two kinds of blasting are available: external charge blasting and confined blasting. The detonation power of the latter is 10 to 50 times larger than that of the former. A detruction test using several kinds of spherical form model calculus and lead azide explosive was performed. The formula to calculate the suitable explosive dose was determined experimentally as shown below. (formula; see text) Thus the theory in general industrial blasting with massive explosives was proved to be effective also in microexplosion with small explosives. An original electric drill system was developed to make a hole in stones for confined blasting. 60 cases, including 2 cases of giant bladder stones over 100 g in weight, were successfully treated by confined blasting using this system without any complication. We consider that any bladder stones, however big or however many, can be treated by microexplosion lithotripsy with confined blasting.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nick Cannell; Dr. Mark Samonds; Adi Sholapurwalla

The investment casting process is an expendable mold process where wax patterns of the part and rigging are molded, assembled, shelled and melted to produce a ceramic mold matching the shape of the component to be cast. Investment casting is an important manufacturing method for critical parts because of the ability to maintain dimensional shape and tolerances. However, these tolerances can be easily exceeded if the molding components do not maintain their individual shapes well. In the investment casting process there are several opportunities for the final casting shape to not maintain the intended size and shape, such as shrinkagemore » of the wax in the injection tool, the modification of the shape during shell heating, and with the thermal shrink and distortion in the casting process. Studies have been completed to look at the casting and shell distortions through the process in earlier phases of this project. Dr. Adrian Sabau at Oak Ridge National Labs performed characterizations and validations of 17-4 PH stainless steel in primarily fused silica shell systems with good agreement between analysis results and experimental data. Further tasks provided material property measurements of wax and methodology for employing a viscoelastic definition of wax materials into software. The final set of tasks involved the implementation of the findings into the commercial casting analysis software ProCAST, owned and maintained by ESI Group. This included: o the transfer of the wax material property data from its raw form into separate temperature-dependent thermophysical and mechanical property datasets o adding this wax material property data into an easily viewable and modifiable user interface within the pre-processing application of the ProCAST suite, namely PreCAST o and validating the data and viscoelastic wax model with respect to experimental results« less

Genetic profile based upon 15 microsatellites of four caste groups of the eastern Indian state, Bihar.

PubMed

Ashma, R; Kashyap, V K

2003-01-01

The formation of caste groups among the Hindu community and the practice of endogamy exert a great impact on the genetic structure and diversity of the Indian population. Allele frequency data of 15 microsatellite loci clearly portray the genetic diversity and relatedness among four socio-culturally advanced caste groups: Brahmin, Bhumihar, Rajput and Kayasth of Caucasoid ethnicity of Bihar. The study seeks to understand the impact of the man-made caste system on the genetic profile of the four major caste groups of Bihar. Computation of average heterozygosity, most frequent allele, allele diversity and coefficient of gene differentiation (Gst), along with genetic distance (DA)and principal coordinate analysis were performed to assess intra-population and inter-population diversity. The average Gst value for all the loci was 0.012 +/- 0.0033, and the level of average heterozygosity was approximately 75.5%, indicating genetic similarity and intra-population diversity. Genetic distance (DA) values and the phylogenetic tree along with other higher caste groups of India indicate the relative distance between them. The present study clearly depicts the genetic profile of these caste groups, their inherent closeness in the past, and the impact of the imposed caste system that later restricted the gene flow. The study highlights the status of Bhumihar and Kayasth in the Hindu caste system. The former was found clustering with the Brahmin group (as expected, since Bhumihar is known to be a subclass of Brahmin), whereas the distance between the Brahmin and Kayasth caste groups was found to be large. North-eastern Indian Mongoloids form a separate cluster.

Evidence for a distinct gut microbiome in kidney stone formers compared to non-stone formers.

PubMed

Stern, Joshua M; Moazami, Saman; Qiu, Yunping; Kurland, Irwin; Chen, Zigui; Agalliu, Ilir; Burk, Robert; Davies, Kelvin P

2016-10-01

The trillions of microbes that colonize our adult intestine are referred to as the gut microbiome (GMB). Functionally it behaves as a metabolic organ that communicates with, and complements, our own human metabolic apparatus. While the relationship between the GMB and kidney stone disease (KSD) has not been investigated, dysbiosis of the GMB has been associated with diabetes, obesity and cardiovascular disease. In this pilot study we sought to identify unique changes in the GMB of kidney stone patients compared to patients without KSD. With an IRB-approved protocol we enrolled 29 patients into our pilot study. 23 patients were kidney stone formers and six were non-stone forming controls. Specimens were collected after a 6h fast and were flash frozen in dry ice and then stored at -80 °C. Microbiome: determination of bacterial abundance was by analysis of 16 s rRNA marker gene sequences using next generation sequencing. Sequencing of the GMB identified 178 bacterial genera. The five most abundant enterotypes within each group made up to greater than 50 % of the bacterial abundance identified. Bacteroides was 3.4 times more abundant in the KSD group as compared to control (34.9 vs 10.2 %; p = 0.001). Prevotella was 2.8 times more abundant in the control group as compared to the KSD group (34.7 vs 12.3 %; p = 0.005). In a multivariate analysis including age, gender, BMI, and DM, kidney stone disease remained an increased risk for high prevalence for Bacteroides (OR = 3.26, p = 0.033), whereas there was an inverse association with Prevotella (OR = 0.37, p = 0.043). There were no statistically significant differences in bacterial abundance levels for Bacteroides or Prevotella when comparing patients with and without DM, obesity (BMI >30), HTN or HLD. 11 kidney stone patients completed 24 h urine analysis at the time of this writing. Looking at the bacterial genuses with at least 4 % abundance in the kidney stone group, Eubacterium was inversely correlated with oxalate levels (r = -0.60, p < 0.06) and Escherichia trended to an inverse correlation with citrate (r = -0.56, p < 0.08). We also compared bacterial abundance between uric acid (UA) stone formers (n = 5) and non UA stone formers (n = 18) and found no significant difference between them. We identified two genus of bacteria in the GMB that had significant association with KSD. Interestingly, components of the 24-h urine appear to be correlated to bacterial abundance. These preliminary studies for the first time associate differences in the GMB with kidney stone formation. Further studies are warranted to evaluate the potential causative role of preexisting dysbiosis in kidney stone disease.

Comparison of Fit of Dentures Fabricated by Traditional Techniques Versus CAD/CAM Technology.

PubMed

McLaughlin, J Bryan; Ramos, Van; Dickinson, Douglas P

2017-11-14

To compare the shrinkage of denture bases fabricated by three methods: CAD/CAM, compression molding, and injection molding. The effect of arch form and palate depth was also tested. Nine titanium casts, representing combinations of tapered, ovoid, and square arch forms and shallow, medium, and deep palate depths, were fabricated using electron beam melting (EBM) technology. For each base fabrication method, three poly(vinyl siloxane) impressions were made from each cast, 27 dentures for each method. Compression-molded dentures were fabricated using Lucitone 199 poly methyl methacrylate (PMMA), and injection molded dentures with Ivobase's Hybrid Pink PMMA. For CAD/CAM, denture bases were designed and milled by Avadent using their Light PMMA. To quantify the space between the denture and the master cast, silicone duplicating material was placed in the intaglio of the dentures, the titanium master cast was seated under pressure, and the silicone was then trimmed and recovered. Three silicone measurements per denture were recorded, for a total of 243 measurements. Each silicone measurement was weighed and adjusted to the surface area of the respective arch, giving an average and standard deviation for each denture. Comparison of manufacturing methods showed a statistically significant difference (p = 0.0001). Using a ratio of the means, compression molding had on average 41% to 47% more space than injection molding and CAD/CAM. Comparison of arch/palate forms showed a statistically significant difference (p = 0.023), with shallow palate forms having more space with compression molding. The ovoid shallow form showed CAD/CAM and compression molding had more space than injection molding. Overall, injection molding and CAD/CAM fabrication methods produced equally well-fitting dentures, with both having a better fit than compression molding. Shallow palates appear to be more affected by shrinkage than medium or deep palates. Shallow ovoid arch forms appear to benefit from the use of injection molding compared to CAD/CAM and compression molding. © 2017 by the American College of Prosthodontists.

Characterization of solidified radioactive waste due to the incorporation of high- and low-density polyethylene granules and titanium dioxide in mortar matrices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peric, A.

1997-12-31

The rutile form of titanium dioxide and granules of high density polyethylene (PEHD) and low density polyethylene (PELD) were used to prepare mortar matrices for immobilization of radioactive waste materials containing {sup 137}Cs. PELD, PEHD and TiO{sub 2} were added to mortar matrix preparations with the objective of improving physico-chemical characteristics of the radwaste-mortar matrix mixtures, in particular the leach-rate of the immobilized radionuclide. One type of PELD and two types of PEHD were used to replace 50 wt.% of stone granules normally used in the matrix, in order to decrease the porosity and density of the mortar matrix andmore » to avoid segregation of the stone particles at the bottom of the immobilized radioactive waste cylindrical form. TiO{sub 2} was also added to the mortar formulation, replacing 5 and 8 wt.% of the total cement weight. Cured samples were investigated under temperature stress conditions, where the temperature extremes were: T{sub min} = {minus}20 C, T{sub max} = +70 C. Samples were periodically immersed in distilled water at the ambient room temperature, after each freezing and heating treatment. Results of accelerated leaching experiments for these samples and samples prepared exclusively with polyethylenes replacing 100% of the stone granules and TiO{sub 2}, treated in nonaccelerated leaching experiments, were compared. Even using an accelerated ageing leach test that overestimates {sup 137}Cs leach rates, it can be deduced, that radionuclide leach rates from the radioactive waste mortar mixture forms were improved. Leach rates decreased from 5%, for the material prepared with stone aggregate, to 3.1 to 4.0%, for the materials prepared solely with PEHD, PELD or TiO{sub 2}, and to about 3% for all six types of the TiO{sub 2}-PEHD and TiO{sub 2}-PELD mixtures tested.« less

The Design of 3D-Printed Lattice-Reinforced Thickness-Varying Shell Molds for Castings

PubMed Central

Shangguan, Haolong; Kang, Jinwu; Yi, Jihao; Zhang, Xiaochuan; Wang, Xiang; Wang, Haibin; Huang, Tao

2018-01-01

3D printing technologies have been used gradually for the fabrication of sand molds and cores for castings, even though these molds and cores are dense structures. In this paper, a generation method for lattice-reinforced thickness-varying shell molds is proposed and presented. The first step is the discretization of the STL (Stereo Lithography) model of a casting into finite difference meshes. After this, a shell is formed by surrounding the casting with varying thickness, which is roughly proportional to the surface temperature distribution of the casting that is acquired by virtually cooling it in the environment. A regular lattice is subsequently constructed to support the shell. The outside surface of the shell and lattice in the cubic mesh format is then converted to STL format to serve as the external surface of the new shell mold. The internal surface of the new mold is the casting’s surface with the normals of all of the triangles in STL format reversed. Experimental verification was performed on an Al alloy wheel hub casting. Its lattice-reinforced thickness-varying shell mold was generated by the proposed method and fabricated by the binder jetting 3D printing. The poured wheel hub casting was sound and of good surface smoothness. The cooling rate of the wheel hub casting was greatly increased due to the shell mold structure. This lattice-reinforced thickness-varying shell mold generation method is of great significance for mold design for castings to achieve cooling control. PMID:29601543

Alloy with metallic glass and quasi-crystalline properties

DOEpatents

Xing, Li-Qian; Hufnagel, Todd C.; Ramesh, Kaliat T.

2004-02-17

An alloy is described that is capable of forming a metallic glass at moderate cooling rates and exhibits large plastic flow at ambient temperature. Preferably, the alloy has a composition of (Zr, Hf).sub.a Ta.sub.b Ti.sub.c Cu.sub.d Ni.sub.e Al.sub.f, where the composition ranges (in atomic percent) are 45.ltoreq.a.ltoreq.70, 3.ltoreq.b.ltoreq.7.5, 0.ltoreq.c.ltoreq.4, 3.ltoreq.b+c.ltoreq.10, 10.ltoreq.d.ltoreq.30, 0.ltoreq.e.ltoreq.20, 10.ltoreq.d+e.ltoreq.35, and 5.ltoreq.f.ltoreq.15. The alloy may be cast into a bulk solid with disordered atomic-scale structure, i.e., a metallic glass, by a variety of techniques including copper mold die casting and planar flow casting. The as-cast amorphous solid has good ductility while retaining all of the characteristic features of known metallic glasses, including a distinct glass transition, a supercooled liquid region, and an absence of long-range atomic order. The alloy may be used to form a composite structure including quasi-crystals embedded in an amorphous matrix. Such a composite quasi-crystalline structure has much higher mechanical strength than a crystalline structure.

Wear behavioral study of as cast and 7 hr homogenized Al25Mg2Si2Cu4Ni alloy at constant load

NASA Astrophysics Data System (ADS)

Harlapur, M. D.; Sondur, D. G.; Akkimardi, V. G.; Mallapur, D. G.

2018-04-01

In the current study, the wear behavior of as cast and 7 hr homogenized Al25Mg2Si2Cu4Ni alloy has been investigated. Microstructure, SEM and EDS results confirm the presence of different intermetallic and their effects on wear properties of Al25Mg2Si2Cu4Ni alloy in as cast as well as aged condition. Alloying main elements like Si, Cu, Mg and Ni partly dissolve in the primary α-Al matrix and to some amount present in the form of intermetallic phases. SEM structure of as cast alloy shows blocks of Mg2Si which is at random distributed in the aluminium matrix. Precipitates of Al2Cu in the form of Chinese script are also observed. Also `Q' phase (Al-Si-Cu-Mg) be distributed uniformly into the aluminium matrix. Few coarsened platelets of Ni are seen. In case of 7 hr homogenized samples blocks of Mg2Si get rounded at the corners, Platelets of Ni get fragmented and distributed uniformly in the aluminium matrix. Results show improved volumetric wear resistance and reduced coefficient of friction after homogenizing heat treatment.

Rare calcium oxalate monohydrate calculus attached to the wall of the renal pelvis.

PubMed

Grases, Felix; Costa-Bauza, Antonia; Prieto, Rafael M; Saus, Carlos; Servera, Antonio; García-Miralles, Reyes; Benejam, Joan

2011-04-01

Most renal calculi can be classified using well-established criteria in a manner that reflects both composition and fine structure under specific pathophysiological conditions. However, when a large patient population is considered, rare renal calculi invariably appear, some of which have never been classified; careful study is required to establish stone etiology in such cases. The patient in the present case report formed two types of calculi. One was attached on the wall of the renal pelvis near the ureter and part of the calculus was embedded inside pelvic renal tissue. The calculus developed on an ossified calcification located in the pelvis tissue. Current knowledge on the development of calcification in soft tissues suggests a pre-existing injury as an inducer of its development. A mechanism of calculus formation is proposed. The second stone was a typical jack-stone calculus. © 2011 The Japanese Urological Association.

Caste- and development-associated gene expression in a lower termite

PubMed Central

Scharf, Michael E; Wu-Scharf, Dancia; Pittendrigh, Barry R; Bennett, Gary W

2003-01-01

Background Social insects such as termites express dramatic polyphenism (the occurrence of multiple forms in a species on the basis of differential gene expression) both in association with caste differentiation and between castes after differentiation. We have used cDNA macroarrays to compare gene expression between polyphenic castes and intermediary developmental stages of the termite Reticulitermes flavipes. Results We identified differentially expressed genes from nine ontogenic categories. Quantitative PCR was used to quantify precise differences in gene expression between castes and between intermediary developmental stages. We found worker and nymph-biased expression of transcripts encoding termite and endosymbiont cellulases; presoldier-biased expression of transcripts encoding the storage/hormone-binding protein vitellogenin; and soldier-biased expression of gene transcripts encoding two transcription/translation factors, two signal transduction factors and four cytoskeletal/muscle proteins. The two transcription/translation factors showed significant homology to the bicaudal and bric-a-brac developmental genes of Drosophila. Conclusions Our results show differential expression of regulatory, structural and enzyme-coding genes in association with termite castes and their developmental precursor stages. They also provide the first glimpse into how insect endosymbiont cellulase gene expression can vary in association with the caste of a host. These findings shed light on molecular processes associated with termite biology, polyphenism, caste differentiation and development and highlight potentially interesting variations in developmental themes between termites, other insects, and higher animals. PMID:14519197

Ursodiol

MedlinePlus

... gallbladder. It works by decreasing the production of cholesterol and by dissolving the cholesterol in bile so that it cannot form stones. ... Atromid-S), colestipol (Colestid), medications that lower lipid or cholesterol levels, medications that contain estrogen (including birth control ...

Investigation of Meniscus Region Behavior and Oscillation Mark Formation in Steel Continuous Casting Using a Transient Thermo-Fluid Model

NASA Astrophysics Data System (ADS)

Blaes, Carly

In the continuous casting of steel, many complex phenomena in the meniscus region of the mold are responsible for the formation of oscillation marks. Oscillation marks are depressions found around the perimeter of continuously cast steel slabs, which if too large can lead to cracking in steel slabs. Therefore, knowledge on how to minimize the size of oscillation marks is very valuable. A computational model was created of the meniscus region, which includes transient multiphase fluid flow of slag and steel, with low-Reynolds turbulence, heat transfer in the mold, slag, and steel, steel shell solidification, mold oscillation, and temperature-dependent properties. This model was first validated using previous experimental and plant data. The model was then used to study the impact of varying casting parameters, including oscillation frequency, stroke, modification ratio, casting speed, molten steel level fluctuations, and temperature-dependent slag properties and surface tension on the oscillation mark shape, and other aspects of thermal-flow behavior during each oscillation cycle, including heat flux profile, slag consumption and mold friction. The first half of oscillation marks were formed during negative strip time as the slag rim pushed molten steel away from the mold wall and that the second half of oscillation marks were formed during positive strip time as the molten steel is drawn near the mold wall due to the upstroke of the mold. Oscillation mark depth was found to decrease with increasing frequency, modification ratio, casting speed, and slag viscosity, while oscillation mark depth was found to increase with increasing stroke. Oscillation mark width was only found to increase due to increases in pitch, which can be contributed to decreasing frequency or increasing casting speed. While many observations were made in this study, in general, oscillation mark depth and total slag consumption increase with increasing negative strip time, while the average heat flux and average mold friction decrease with increasing negative strip time.

Dental anomalies in an orthodontic patient population with maxillary lateral incisor agenesis.

PubMed

Citak, Mehmet; Cakici, Elif Bahar; Benkli, Yasin Atakan; Cakici, Fatih; Bektas, Bircan; Buyuk, Suleyman Kutalmış

2016-01-01

The purpose of this study was to evaluate the prevalence of dental anomalies in a subpopulation of orthodontic patients with agenesis of maxillary lateral incisors (MLI). The material of the present study included the records of the 1964 orthodontic patients. Panoramic radiographs and dental casts were used to analyze other associated eight dental anomalies, including agenesis of other teeth, dens invaginatus, dens evaginatus, peg shaped MLI, taurodontism, pulp stone, root dilaceration and maxillary canine impaction. Out of the 1964 patients examined, 90 were found to have agenesis of MLI, representing a prevalence of 4.6%. The most commonly found associated-anomalies were agenesis of other teeth (23.3%), peg-shaped MLIs (15.6%), taurodontism (42.2%), and dilacerated teeth (18.9%). Permanent tooth agenesis, taurodontism, peg-shaped maxillary lateral incisor, and root dilacerations are frequently associated with maxillary lateral incisor agenesis.

Low Velocity Impact Behavior of Glass Filled Fiber-Reinforced Thermoplastic Engine Components

PubMed Central

Mouti, Zakaria; Westwood, Keith; Kayvantash, Kambiz; Njuguna, James

2010-01-01

This paper concerns automotive parts located underneath the engine and in particular the engine oil pan. Classically made of stamped steel or cast aluminum, new developments have allowed the manufacture oil pans with polyamide 66 reinforced by 35% weight of short glass fiber. However, polyamides have some limitations and the most significant is their response to localized impact loading. The nature of the impact considered here is of a typical stone collected from the road and projected into the oil pan.  Low velocity impact investigations were carried out using a gas gun and drop weight tower.  The study shows that the design of the oil pan has a significant contribution in the shock absorption. In addition to the material properties, the geometry and the ribbing both cleverly combined, increase the impact resistance of the component significantly. Areas of oil pan design improvement have been identified and conclusions drawn.

Fixture for forming evaporative pattern (EPC) process patterns

DOEpatents

Turner, Paul C.; Jordan, Ronald R.; Hansen, Jeffrey S.

1993-01-01

A method of casting metal using evaporative pattern casting process patterns in combination with a fixture for creating and maintaining a desired configuration in flexible patterns. A pattern is constructed and gently bent to the curvature of a suitable fixture. String or thin wire, which burns off during casting, is used to tie the pattern to the fixture. The fixture with pattern is dipped in a commercially available refractory wash to prevent metal adherence and sticking to the fixture. When the refractory wash is dry, the fixture and pattern are placed in a flask, and sand is added and compacted by vibration. The pattern remains in position, restrained by the fixture. Metal that is poured directly into the pattern replaces the pattern exactly but does not contact or weld to the fixture due to the protective refractory layer. When solid, the casting is easily separated from the fixture. The fixture can be cleaned for reuse in conventional casting cleaning equipment.

EBSD Study on Grain Boundary and Microtexture Evolutions During Friction Stir Processing of A413 Cast Aluminum Alloy

NASA Astrophysics Data System (ADS)

Shamanian, Morteza; Mostaan, Hossein; Safari, Mehdi; Szpunar, Jerzy A.

2016-07-01

The as-cast Al alloys contain heterogeneous distributions of non-deforming particles due to non-equilibrium solidification effects. Therefore, these alloys have poor tribological and mechanical behaviors. It is well known that using friction stir processing (FSP), very fine microstructure is created in the as-cast Al alloys, while their wear resistance can be improved. In this research work, FSP is used to locally refine a surface layer of the coarse as-cast microstructure of cast A413 Al alloy. The main objective of this study is to investigate the effect of FSP on microstructure and microtexture evolutions in A413 cast Al alloy. The grain boundary character distribution, grain structure, and microtexture evolutions in as-cast and friction stir processed A413 Al alloy are analyzed by electron back scatter diffraction technique. It is found that with the FSP, the fraction of low ∑boundary such as ∑3, 7, and 9 are increased. The obtained results show that there are no deformation texture components in the structure of friction stir processed samples. However, some of the main recrystallization texture components such as BR and cubeND are formed during FSP which indicate the occurrence of dynamic recrystallization phenomenon due to the severe plastic deformation induced by the rotation of tool.

Calcium carbonate precipitation by heterotrophic bacteria isolated from biofilms formed on deteriorated ignimbrite stones: influence of calcium on EPS production and biofilm formation by these isolates.

PubMed

López-Moreno, Angélica; Sepúlveda-Sánchez, José David; Mercedes Alonso Guzmán, Elia Mercedes; Le Borgne, Sylvie

2014-01-01

Heterotrophic CaCO3-precipitating bacteria were isolated from biofilms on deteriorated ignimbrites, siliceous acidic rocks, from Morelia Cathedral (Mexico) and identified as Enterobacter cancerogenus (22e), Bacillus sp. (32a) and Bacillus subtilis (52g). In solid medium, 22e and 32a precipitated calcite and vaterite while 52g produced calcite. Urease activity was detected in these isolates and CaCO3 precipitation increased in the presence of urea in the liquid medium. In the presence of calcium, EPS production decreased in 22e and 32a and increased in 52g. Under laboratory conditions, ignimbrite colonization by these isolates only occurred in the presence of calcium and no CaCO3 was precipitated. Calcium may therefore be important for biofilm formation on stones. The importance of the type of stone, here a siliceous stone, on biological colonization is emphasized. This calcium effect has not been reported on calcareous materials. The importance of the effect of calcium on EPS production and biofilm formation is discussed in relation to other applications of CaCO3 precipitation by bacteria.

Renal diseases in adults with cystic fibrosis: a 40 year single centre experience.

PubMed

Wilcock, M J; Ruddick, A; Gyi, K M; Hodson, M E

2015-10-01

There is a sizable literature describing renal disease in patients with cystic fibrosis. Previous studies have focused on single disease processes alone, most commonly renal stone disease or acute kidney injury. In this study we report for the first time on the prevalence of all forms of renal disease in a cystic fibrosis population. A retrospective review of adult patients with cystic fibrosis attending the Adult Cystic Fibrosis Department at the Royal Brompton Hospital was carried out by searching the department's database to identify patients with renal problems and subsequently retrieving clinical information from medical notes. The prevalence of all renal diseases in our population was 5.1 %. The most commonly identified problem was renal stones. At 2.0 % the prevalence of renal stones in adult patients with cystic fibrosis was comparable to the general population. A range of other renal diseases were identified, the next most common being drug-induced acute kidney injury. A range of cystic fibrosis independent and attributable diseases has been identified but no cystic fibrosis specific disease. In contrast to other cystic fibrosis centres no increased prevalence of renal stones was found.

Tool making, hand morphology and fossil hominins.

PubMed

Marzke, Mary W

2013-11-19

Was stone tool making a factor in the evolution of human hand morphology? Is it possible to find evidence in fossil hominin hands for this capability? These questions are being addressed with increasingly sophisticated studies that are testing two hypotheses; (i) that humans have unique patterns of grip and hand movement capabilities compatible with effective stone tool making and use of the tools and, if this is the case, (ii) that there exist unique patterns of morphology in human hands that are consistent with these capabilities. Comparative analyses of human stone tool behaviours and chimpanzee feeding behaviours have revealed a distinctive set of forceful pinch grips by humans that are effective in the control of stones by one hand during manufacture and use of the tools. Comparative dissections, kinematic analyses and biomechanical studies indicate that humans do have a unique pattern of muscle architecture and joint surface form and functions consistent with the derived capabilities. A major remaining challenge is to identify skeletal features that reflect the full morphological pattern, and therefore may serve as clues to fossil hominin manipulative capabilities. Hominin fossils are evaluated for evidence of patterns of derived human grip and stress-accommodation features.

The Role of the Papillary Epithelium in Stone Growth

NASA Astrophysics Data System (ADS)

Bergsland, Kristin J.

2007-04-01

The papillary surface epithelium (PSE) covers the renal papilla in mammalian kidneys and serves as a diffusion barrier between the urine on the apical surface and the interstitium on the basolateral surface. The PSE also plays a physiological role in transport of solutes between the urine and interstitium both by active transport and paracellular pathways. Permeability of the PSE may be affected by alterations in specific transporters, components of intercellular tight junctions, cell surface glycosaminoglycans and urine composition. In idiopathic calcium oxalate (CaOx) stone formers, apatite deposits known as Randall's plaque form in the papillary interstitium and lodge beneath the PSE. The presence of plaque may perturb the normal function of the PSE, possibly by provoking the up-regulation of pro-inflammatory cytokines such as TNFα in the interstitium. Disruption of the epithelial barrier may lead to increased permeability and exposure of the plaque matrix to urine constituents, followed by loss of the PSE and growth of CaOx stone over the plaque. To investigate the role of the PSE in stone development, new experimental systems are needed, including animal models of plaque formation as well as cell culture systems for papillary epithelial cells.

Tool making, hand morphology and fossil hominins

PubMed Central

Marzke, Mary W.

2013-01-01

Was stone tool making a factor in the evolution of human hand morphology? Is it possible to find evidence in fossil hominin hands for this capability? These questions are being addressed with increasingly sophisticated studies that are testing two hypotheses; (i) that humans have unique patterns of grip and hand movement capabilities compatible with effective stone tool making and use of the tools and, if this is the case, (ii) that there exist unique patterns of morphology in human hands that are consistent with these capabilities. Comparative analyses of human stone tool behaviours and chimpanzee feeding behaviours have revealed a distinctive set of forceful pinch grips by humans that are effective in the control of stones by one hand during manufacture and use of the tools. Comparative dissections, kinematic analyses and biomechanical studies indicate that humans do have a unique pattern of muscle architecture and joint surface form and functions consistent with the derived capabilities. A major remaining challenge is to identify skeletal features that reflect the full morphological pattern, and therefore may serve as clues to fossil hominin manipulative capabilities. Hominin fossils are evaluated for evidence of patterns of derived human grip and stress-accommodation features. PMID:24101624

Sir William Osler's perceptions of urolithiasis and the case of the indigo calculus.

PubMed

Moran, Michael E; Das, Sakti; Rosenberg, Stuart A

2005-12-01

Sir William Osler published his textbook, The Principles and Practice of Medicine, in 1892. It became the definitive treatise on a wide variety of diseases. The section on nephrolithiasis clearly presents the etiology, pathology, symptoms, diagnosis, and treatments. What remains a mystery is the mention, under rare forms of human stones, of a type called "indigo." A search of Index Medicus starting from 1909 backward to its inception in 1879 was performed for key words "indigo," "calculus," "renal" or "bladder stones" and "indicanuria." Twelve textbooks of urology published before 1940 were scrutinized for references to indigo calculi. Only two references to indigo were found, both related to its use for treating constipation (1887 and 1891). Of the 12 textbooks, only 4 make passing reference to "indigo stones." They all mention that such calculi are very rare, but direct references to cases are lacking. One textbook references a study of blue stones from Egyptian mummies. It is unlikely that Osler's reference to an indigo calculus was taken lightly during his writing of The Principles and Practice of Medicine. The case of the indigo calculus is fascinating and perhaps enlightening if only for the source of Osler's intrigue.

Pneumatic versus laser ureteroscopic lithotripsy: a comparison of initial outcomes and cost.

PubMed

Demir, Aslan; Karadağ, Mert Ali; Ceçen, Kurşat; Uslu, Mehmet; Arslan, Omer Erkam

2014-11-01

To audit the cost of laser versus pneumatic semirigid ureteroscopic lithotripsy and to analyze their relative initial outcomes and cost. Hundred and eighty-seven patients who underwent semirigid ureteroscopic lithotripsy were analyzed retrospectively in terms of age and sex of the patients; location and size of the stones; the type of probe and ancillary equipment such as guide wire, basket catheter, JJ stent requirements; irrigation amount; operation time; the cost of the anesthesia and further treatments such as a JJ stent removal operation and shock wave lithotripsy requirements and their costs. Two groups were formed based on this type of lithotripters, pneumatic and laser lithotripsy. Operation times (min.) in terms of the stone size, for stones <100 and >100 mm(2) were 20.75 ± 10.78 and 25.82 ± 14.23, respectively (p = 0.007). Operation times for the pneumatic and laser groups were 33.05 ± 11.36 and 15.25 ± 6.14, respectively (p < 0.05).The stone-free rates for pneumatic and laser groups were 89.6 % (n = 69) and 98.2 % (n = 108), respectively (p = 0.01). The mean cost of the operations for each of the study groups was 261.5 ± 66.13 and 311.7 ± 51.97 US$, respectively (p = 0.001). The mean cost in terms of the stone size, for stones <100 and >100 mm(2), was 272.86 ± 53.05 and 323.71 ± 66.88 US$, respectively (p = 0.01). It seems that usage of laser lithotripsy (LL) in patients with ureteral stones is more effective than pneumatic lithotripsy (PL) in terms of operation time and SF rate. On the other hand, the mean cost of LL seems to be more expensive than PL. Urologists should think these parameters before the choice of these two treatment modalities. The higher the effectiveness, the greater the cost.

A new approach to assess the chemical composition of powder deposits damaging the stone surfaces of historical monuments.

PubMed

Fermo, Paola; Turrion, Raquel Gonzalez; Rosa, Mario; Omegna, Alessandra

2015-04-01

The issue of conservation of the monumental heritage worldwide is mainly related to atmospheric pollution that causes the degradation of stone surfaces. The powder deposits present on the stone monuments reflect the composition of the aerosol particulate matter (PM) to which the surfaces are exposed, so the chemical characterization of the outermost damaged layers is necessary in order to adopt mitigation measurements to reduce PM emissions. In the present paper, a new analytical approach is proposed to investigate the chemical composition of powder deposits present on Angera stone, a dolomitic rock used in the Richini courtyard, a masterpiece of Lombard Baroque and placed in Milan. Inorganic and organic components present in these deposits have been analyzed by IC (ion chromatography) and a new approach mainly bases on thermal analyses, respectively. Gypsum is the main inorganic constituent indicating a composition similar to that of black crusts, hard black patina covering the degraded building surfaces. Ammonium nitrate present in the powder is able to react with the stone substrate to form magnesium nitrate which can migrate into the porous stone. The carbonaceous fraction powder deposits (i.e. OC = Organic Carbon and EC = Elemental Carbon) have been quantified by a new simple thermal approach based on carbon hydrogen nitrogen (CHN) analysis. The presence of high concentration of EC confirms that the powder deposits are evolving to black crust. Low values of water-soluble organic carbon (WSOC, determined by total organic carbon-TOC), with respect to what is normally found in PM, may indicate a migration process of organic substances into the stone with a worsening of the conservation conditions. The presence of heavy metals of anthropogenic origin and acting as catalysts in the black crust formation process has been highlighted by SEM-EDS (electron microscopy coupled with an energy dispersive spectrometer) as well.

Salt-enhanced chemical weathering of building materials and bacterial mineralization of calcium carbonate as a treatment

NASA Astrophysics Data System (ADS)

Schiro, M.; Ruiz-Agudo, E.; Jroundi, F.; Gonzalez-Muñoz, M. T.; Rodriguez-Navarro, C.

2012-04-01

Salt weathering is an important mechanism contributing to the degradation and loss of stone building materials. In addition to the physical weathering resulting from crystallization pressure, the presence of salts in solution greatly enhances the chemical weathering potential of pore waters. Flow through experiments quantify the dissolution rates of calcite and quartz grains (63-125 micrometer diameter) when subjected to 1.0 ionic strength solutions of MgSO4, MgCl, Na2SO4 or NaCl. Results indicate that the identity of the cation is the primary control over the dissolution rate of both calcite and quartz substrates, with salt-enhanced dissolution occurring most rapidly in Mg2+ bearing solutions. It has been observed that weathering rates of rocks in nature, as well as building stones, are slowed down by naturally occurring or artificially produced patinas. These tend to be bacterially produced, durable mineralized coatings that lend some degree of protection to the underlying stone surface [1]. Our research shows that bacterially produced carbonate coatings can be quite effective at reducing chemical weathering of stone by soluble salts. The calcite-producing-bacteria used in this study were isolated from stone monuments in Granada, Spain [2] and cultivated in an organic-rich culture medium on a variety of artificial and natural substrates (including limestone, marble, sandstone, quartz, calcite single crystals, glass cover-slips, and sintered porous glass). Scanning electron microscopy (FESEM) was used to image bacterial calcite growth and biofilm formation. In-situ atomic force microscopy (AFM) enabled calculation of dissolution rates of untreated and bacterially treated surfaces. 2D-XRD showed the mineralogy and crystallographic orientation of bacterial calcium carbonate. Results indicate that bacterially produced calcite crystals form a coherent, mechanically resistant surface layer in perfect crystallographic continuity with the calcite substrate (self-epitaxy). These calcite biominerals are more resistant to chemical weathering by salt-enhanced dissolution, apparently due to the incorporation of organics (bacterial exopolymeric substances, EPS). Conversely, on silicate substrates, non-oriented vaterite forms, leading to limited protection. These preliminary results indicate that bacterial treatments have a significant potential to protect the stone built cultural heritage. [1] De Muynck et al. (2010) Ecol. Eng. 36, 118-136. [2] Jimenez-Lopez et al. (2007) Chemosphere 68, 1929-1936.

Anthropogenic salts from deteriorated stones of a historical monument (Kraków, Poland)

NASA Astrophysics Data System (ADS)

Marszałek, Mariola; Prajer, Marta

2017-04-01

The results focus on the stone architectonic elements of the Hebdowski Palace in the Okół, an old, medieval part of Kraków. The object was built around 1400, then rebuilt at the turn of the 17th century and at the first half of the 19th century. Its façade was covered with plaster, whose scaling fragments prior to the renovation in 2015 revealed underneath bricks, particularly in the lower part of the palace. The sandstone elements were used in the main portal, while the limestone ones in window frames of the lower section of the façade, base mouldings, and the buttresses at the corner of Poselska and Senacka streets (one of the oldest streets in Kraków). The stone blocks show various forms of damage, ranging from the accumulation of black crusts and efflorescences to crumbling and scaling of their surfaces. Optical microscopy, scanning electron microscopy (SEM-EDS), micro-Raman spectroscopy and X-ray diffractometry (XRD) were used for analysing deterioration products of the stone samples that were collected during the restoration campaign of 2015. The salt minerals detected in the efflorescences and the black crusts include mainly gypsum CaSO4•2H2O and halite NaCl. On the surface of the limestone gypsum is accompanied by oxalates (whewellite CaC2O4•H2O and/or weddellite CaC2O4•2H2O). The black crust developed on both stone types also contain numerous dust particles and a carbonaceous matter, probably soot. The origin of the anthropogenic salts can be mainly assigned to air pollution, to the stones themselves (mainly in the case of the limestone), and to migration of ions from some elements of the façade (e.g. plaster) in the case of the sandstone. The chemicals used for removing ice from streets and pavements (chiefly NaCl and CaCl2) also seem to be important in the formations of the salts. Finally, the existence of simple life forms, such as lichens and fungi, could result in the precipitation of oxalates. This work has been financially supported by AGH University of Science and Technology (statutory grant No. 11.11.140.319).

Characterization and Properties of Micro-arc Composite Ceramic Coatings on Magnesium Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Long; Jiang, Bailing; Ge, Yanfeng

2013-05-21

Magnesium alloys are of growing interest for many industrial applications due to their favorable strength-to-weight ratio and excellent cast ability. However, one of the limiting factors in the use of magnesium on production vehicles is its poor corrosion resistance. Micro-arc Composite Ceramic (MCC) coatings on AZ91D magnesium alloys were prepared in combination with Micro-arc Oxidation (MAO) and electrophoresis technologies. The microstructure, corrosion resistance, abrasion resistance, stone impact resistance, thermal shock resistance and adhesion of MCC coating were studied, respectively. The surface and cross-section morphologies of MAO and MCC coating showed that the outer organic coating filled the holes on themore » surface of the MAO coating. It acted as a shelter on the MAO coating surface when the MCC coatings were exposed to corrosive environments. The corrosion resistance of the MCC coating was characterized by a copper-accelerated acetic acid salt spray test. The testing results showed that the creep back from scribe lines was less than 1mm and completely fit the evaluation standard. The composite structure of the MCC coating vastly improved the corrosion resistance of Mg alloys. According to testing standards, the resistance to abrasion, stone impact resistance, thermal shock resistance and adhesion of MCC coatings completely met the evaluation standard requirements. The MCC coated AZ91D magnesium alloys possessed excellent properties; this is a promising corrosion and wear resistance surface treatment technology on magnesium alloys for production vehicles.« less

Mineral inclusions in diamonds from the Kelsey Lake Mine, Colorado, USA: Depleted Archean mantle beneath the Proterozoic Yavapai province

NASA Astrophysics Data System (ADS)

Schulze, Daniel J.; Coopersmith, Howard G.; Harte, Ben; Pizzolato, Lori-Ann

2008-03-01

Thirty-four silicate and oxide inclusions large enough for in situ WDS electron microprobe analysis were exposed by grinding/polishing of 19 diamonds from the Kelsey Lake Mine in the Colorado-Wyoming State Line Kimberlite district. Eighteen olivines, seven Cr-pyropes, four Mg-chromites, and one orthopyroxene in 15 stones belong to the peridotite (P) suite and three garnets and one omphacite in three stones belong to the eclogite (E) suite. The fact that this suite is dominated by the peridotite population is in stark contrast to the other diamond suites studied in the State Line district (Sloan, George Creek), which are overwhelmingly eclogitic. Kelsey Lake olivine inclusions are magnesian (17 of 18 grains in 9 stones are in the range Fo 92.7-93.1), typical of harzburgitic P-suite stones worldwide, but unlike the more Fe-rich (lherzolitic) Sloan olivine suite. Mg-chromites (wt% MgO = 12.8-13.8; wt% Cr 2O 3 = 61.4-66.6) are in the lower MgO range of diamond inclusion chromites worldwide. Seven harzburgitic Cr-pyropes in five stones have moderately low calcium contents (wt% CaO = 3.3-4.3) but are very Cr-rich (wt% Cr 2O 3 = 9.7-16.7). A few stones have been analyzed by SIMS for carbon isotope composition and nitrogen abundance. One peridotitic stone is apparently homogeneous in carbon isotope composition (δ 13C PDB = -6.2‰) but with variable nitrogen abundance (1296-2550 ppm). Carbon isotopes in eclogitic stones range from "normal" for the upper mantle (δ 13C PDB = -5.5‰) to somewhat low (δ 13C PDB = -10.2‰), with little internal variation in individual stones (maximum difference is 3.6‰). Nitrogen contents (2-779 ppm) are lower than in the peridotitic stone, and are lower in cores than in rims. As, worldwide, harzburgite-suite diamonds have been shown to have formed in Archean time, we suggest that the Kelsey Lake diamond population was derived from a block of Archean lithosphere that, at the time of kimberlite eruption, existed beneath the Proterozoic Yavapai province. The mixed diamond inclusion populations from the State Line kimberlites appear to support models in which volumes of Wyoming Craton Archean mantle survive buried beneath Proterozoic continental crust. Such material may be mixed with eclogitic/lherzolitic regimes emplaced beneath or intermingled with the Archean rocks by Proterozoic subduction.

2D and 3D characterization of pore defects in die cast AM60

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Zhuofei; CanmetMATERIALS, 183 Longwood Road South, Hamilton L8P 0A5, Ontario Canada; Maurey, Alexandre

2016-04-15

The widespread application of die castings can be hampered due to the potential of large scale porosity to act as nucleation sites for fracture and fatigue. It is therefore important to develop robust approaches to the characterization of porosity providing parameters that can be linked to the material's mechanical properties. We have tackled this problem in a study of the AM60 die cast Mg alloy, using samples extracted from a prototype shock tower. A quantitative characterization of porosity has been undertaken, analyzing porosity in both 2D (using classical metallographic methods) and in 3D (using X-ray computed tomography (XCT)). Metallographic characterizationmore » results show that shrinkage pores and small gas pores can be distinguished based on their distinct geometrical features. Shrinkage pores are irregular with multiple arms, resulting in a form factor less than 0.4. In contrast, gas pores are generally more circular in shape yielding form factors larger than 0.6. XCT provides deeper insight into the shape of pores, although this understanding is limited by the resolution obtainable by laboratory based XCT. It also shows how 2D sectioning can produce artefacts as single complex pores are sectioned into multiple small pores. - Highlights: • Mg (e.g. AM60) die castings may contain large scale porosity that act as nucleation sites for fracture and fatigue • Quantitative characterization of porosity metallography (2D) and X-ray tomography (3D) is used • Shrinkage pores and small gas pores can be distinguished based on their distinct geometrical features. • Shrinkage pores are irregular giving a form factor < 0.4; gas pores are rounder with form factors > 0.6 • XCT enables pore visualization, although limited by the resolution obtainable by laboratory based XCT.« less

Zero-order release of poorly water-soluble drug from polymeric films made via aqueous slurry casting.

PubMed

Zhang, Lu; Alfano, Joy; Race, Doran; Davé, Rajesh N

2018-05-30

In spite of significant recent interest in polymeric films containing poorly water-soluble drugs, dissolution mechanism of thicker films has not been investigated. Consequently, release mechanisms of poorly water-soluble drugs from thicker hydroxypropyl methylcellulose (HPMC) films are investigated, including assessing thickness above which they exhibit zero-order drug release. Micronized, surface modified particles of griseofulvin, a model drug of BSC class II, were incorporated into aqueous slurry-cast films of different thicknesses (100, 500, 1000, 1500 and 2000 μm). Films 1000 μm and thicker were formed by either stacking two or more layers of ~500 μm, or forming a monolithic thick film. Compared to monolithic thick films, stacked films required simpler manufacturing process (easier casting, short drying time) and resulted in better critical quality attributes (appearance, uniformity of thickness and drug per unit area). Both the film forming approaches exhibited similar release profiles and followed the semi-empirical power law. As thickness increased from 100 μm to 2000 μm, the release mechanism changed from Fickian diffusion to zero-order release for films ≥1000 μm. The diffusional power law exponent, n, achieved value of 1, confirming zero-order release, whereas the percentage drug release varied linearly with sample surface area, and sample thickness due to fixed sample diameter. Thus, multi-layer hydrophilic polymer aqueous slurry-cast thick films containing poorly water-soluble drug particles provide a convenient dosage form capable of zero-order drug release with release time modulated through number of layers. Copyright © 2018 Elsevier B.V. All rights reserved.

Comparative study of two commercially pure titanium casting methods

PubMed Central

RODRIGUES, Renata Cristina Silveira; FARIA, Adriana Claudia Lapria; ORSI, Iara Augusta; de MATTOS, Maria da Gloria Chiarello; MACEDO, Ana Paula; RIBEIRO, Ricardo Faria

2010-01-01

The interest in using titanium to fabricate removable partial denture (RPD) frameworks has increased, but there are few studies evaluating the effects of casting methods on clasp behavior. Objective This study compared the occurrence of porosities and the retentive force of commercially pure titanium (CP Ti) and cobalt-chromium (Co-Cr) removable partial denture circumferential clasps cast by induction/centrifugation and plasma/vacuum-pressure. Material and Methods 72 frameworks were cast from CP Ti (n=36) and Co-Cr alloy (n=36; control group). For each material, 18 frameworks were casted by electromagnetic induction and injected by centrifugation, whereas the other 18 were casted by plasma and injected by vacuum-pressure. For each casting method, three subgroups (n=6) were formed: 0.25 mm, 0.50 mm, and 0.75 mm undercuts. The specimens were radiographed and subjected to an insertion/removal test simulating 5 years of framework use. Data were analyzed by ANOVA and Tukey's to compare materials and cast methods (α=0.05). Results Three of 18 specimens of the induction/centrifugation group and 9 of 18 specimens of plasma/vacuum-pressure cast presented porosities, but only 1 and 7 specimens, respectively, were rejected for simulation test. For Co-Cr alloy, no defects were found. Comparing the casting methods, statistically significant differences (p<0.05) were observed only for the Co-Cr alloy with 0.25 mm and 0.50 mm undercuts. Significant differences were found for the 0.25 mm and 0.75 mm undercuts dependent on the material used. For the 0.50 mm undercut, significant differences were found when the materials were induction casted. Conclusion Although both casting methods produced satisfactory CP Ti RPD frameworks, the occurrence of porosities was greater in the plasma/vacuum-pressure than in the induction/centrifugation method, the latter resulting in higher clasp rigidity, generating higher retention force values. PMID:21085805

Effect of palatal form on movement of teeth during processing of complete denture prosthesis: An in-vitro study.

PubMed

Babu, Sumanth; Manjunath, Shaurya; Vajawat, Mayuri

2016-01-01

The aim of this in-vitro study was to assess the influence of shallow and deep palatal forms on the movement of teeth during the processing of complete denture prosthesis. Maxillary casts with shallow and deep palatal forms were selected and duplicated to make 10 casts of each palatal form. Base plates were constructed and teeth were arranged in their anatomic positions. Metal pins with true apex were placed on the central groove of the right and left first molars and one on the incisive papilla area as a reference point. Casts were scanned using i-CAT Vision Q 1.9 (i-CAT cone beam 3D dental imaging system by Imaging Sciences International, PA, USA), which has 360° rotational tomography. The distances between the apices of metallic pin inserts on the teeth and fitted point of reference were recorded in buccopalatal axes at waxed up stage, after deflasking, and after finishing and polishing. Results showed a statistically significant movement of teeth in shallow and deep palatal forms during all stages of complete denture processing. In shallow palatal form dentures, there was a significant tooth movement in palatal direction between Stages 1 and 2 (P ≤ 0.05) and buccal movement between Stages 2 and 3. In deep palatal form dentures, teeth showed a statistically significant (P ≤ 0.05) movement in buccal direction during all stages of denture processing. Teeth showed significant movement during processing of acrylic resin dentures. Overall, the movement of teeth in shallow palatal form dentures was in palatal direction, whereas in deep palatal form dentures, the movement of teeth was in buccal direction.

Apparatus and method for controlling the temperature of the core of a super-conducting transformer

DOEpatents

Golner, Thomas; Pleva, Edward; Mehta, Shirish

2006-10-10

An apparatus for controlling the temperature of a core of a transformer is provided that includes a core, a shield surrounding the core, a cast formed between the core and the shield, and tubing positioned on the shield. The cast directs heat from the core to the shield and cooling fluid is directed through the tubing to cool the shield.

Next-generation casting technologies and their adaptation and development in Russia: I. at the beginning of a new technological paradigm

NASA Astrophysics Data System (ADS)

Semenov, A. B.; Gavrilenko, A. E.; Semenov, B. I.

2016-12-01

The up-to-date methods of powder metallurgy and casting technology are considered. They can be used to apply the design and technological solutions that are intended to form parts with the optimum space configuration, to deLcrease the number of assembly elements, and to decrease the number of mechanical and welded joints in units.

Effect of extracorporeal shock wave lithotripsy on bacterial viability. Relationship to the treatment of struvite stones.

PubMed

Reid, G; Jewett, M A; Nickel, J C; McLean, R J; Bruce, A W

1990-01-01

The aim of this study was to determine whether extracorporeal shock wave lithotripsy (ESWL) affected the viability of the infecting bacteria within a simulated struvite stone matrix. A strain, Proteus mirabilis 28cii, was prepared in three forms: (1) suspended in saline and urine, (2) artificially encapsulated by suspending in agar beads and (3) artificially encapsulated and mineralised by suspending in agar beads with calcium carbonate crystals. The preparations were placed in capped vials partially immersed in degassed water and held in the focal point of the Siemens Lithostar and given 1,000 shocks. Subsequent viability testing showed that bacteria suspended in urine were greatly affected by shock treatments (55% loss in viability), but incorporation into agar beads negated this effect (even if the cells were exposed to 2000 shocks). Mineralisation of the beads with calcium carbonate crystals caused a decrease in viability of 82% that was significantly different from controls. However, this still left 2.3 X 10(8) viable organisms (82% of 2.8 X 10(8], easily enough to form the focus for further infections. A series of control experiments carried out using an ultrasonic cell sonicator probe gave comparable results to those obtained with ESWL. These results demonstrate the ESWL treatment of infected stones must be accompanied by antimicrobial coverage.

Lithopedion

DTIC Science & Technology

2010-02-01

disappearance of the extrauterine pregnancy. In contrast, chronic ectopic pregnancy often resulting in formation of a lithopedion ( litho = stone; pedion...Corner, Volume 175, February 2010 A calcified extrauterine fetus can have the following forms: (i) lithokelyphos ( litho = rock, kelyphos = shell): only

Numerically modeling oxide entrainment in the filling of castings: The effect of the webber number

NASA Astrophysics Data System (ADS)

Cuesta, Rafael; Delgado, Angel; Maroto, Antonio; Mozo, David

2006-11-01

In the casting of aluminum alloys and, in general, in the casting of film-forming alloys, the entrainment of oxides into the bulk liquid severely reduces the strength of the cast part. To avoid this, the melt velocity must be kept below a certain value, namely critical velocity, which is widely assumed to be 0.5 m/s. In this paper the authors investigate, by means of fluid-dynamic computer simulation, the dependence of critical veiocity on geometrical features of the running channels and thermophysical properties of the molten metal. For each of the geometries studied, once the critical velocity is exceeded, the amount of oxide entrained in the liquid is quantified. The analysis of the results reveals that surface entrainment is much more related to the non-dimensional Webber number than to melt velocity.

CAST-10-2/DOA 2 Airfoil Studies Workshop Results

NASA Technical Reports Server (NTRS)

Ray, Edward J. (Compiler); Hill, Acquilla S. (Compiler)

1989-01-01

During the period of September 23 through 27, 1988, the Transonic Aerodynamics Division at the Langely Research Center hosted an International Workshop on CAST-10-2/DOA 2 Airfoil Studies. The CAST-10 studies were the outgrowth of several cooperative study agreements among the NASA, the NAE of Canada, the DLR of West Germany, and the ONERA of France. Both theoretical and experimental CAST-10 airfoil results that were obtained form an extensive series of tests and studies, were reviewed. These results provided an opportunity to make direct comparisons of adaptive wall test section (AWTS) results from the NASA 0.3-meter Transonic Cryogenic Tunnel and ONERA T-2 AWTS facilities with conventional ventilated wall wind tunnel results from the Canadian high Reynolds number two-dimensional test facility. Individual papers presented during the workshop are included.

Mechanical Properties and Tensile Failure Analysis of Novel Bio-absorbable Mg-Zn-Cu and Mg-Zn-Se Alloys for Endovascular Applications

PubMed Central

Persaud-Sharma, Dharam; Budiansky, Noah; McGoron, Anthony J.

2013-01-01

In this paper, the mechanical properties and tensile failure mechanism of two novel bio-absorbable as-cast Mg-Zn-Se and Mg-Zn-Cu alloys for endovascular medical applications are characterized. Alloys were manufactured using an ARC melting process and tested as-cast with compositions of Mg-Zn-Se and Mg-Zn-Cu, being 98/1/1 wt.% respectively. Nanoindentation testing conducted at room temperature was used to characterize the elastic modulus (E) and surface hardness (H) for both the bare alloys and the air formed oxide layer. As compared to currently available shape memory alloys and degradable as-cast alloys, these experimental alloys possess superior as-cast mechanical properties that can increase their biocompatibility, degradation kinetics, and the potential for medical device creation. PMID:23543822

Ernst Florens Friedrich Chladni (1756-1827) and the origins of modern meteorite research

NASA Astrophysics Data System (ADS)

Marvin, Ursula B.

1996-09-01

In 1794, Ernst F. F. Chladni published a 63-page book Über den Ursprung der von Pallas gefundenen und anderer ihr änlicher Eisenmassen und über einige damit in Verbindung stehende Naturerscheinungen in which he proposed that meteor-stones and iron masses enter the atmosphere from cosmic space and form fireballs as they plunge to Earth. These ideas violated two strongly held contemporary beliefs: (1) fragments of rock and metal do not fall from the sky, and (2) no small bodies exist in space beyond the Moon. From the beginning, Chladni was severely criticised for basing his hypotheses on historical eyewitness reports of falls which others regarded as folk tales and for taking gross liberties with the laws of physics. Eight years later, the study of fallen stones and irons was established as a valid field of investigation. Today, some scholars credit Chladni with founding meteoritics as a science; others regard his contributions as scarcely worthy of mention. Writings by his contemporaries suggest that Chladni's book alone would not have led to changes of prevailing theories; thus, he narrowly escaped the fate of those scientists who propose valid hypotheses prematurely. However between 1794 and 1798, four falls of stones were witnessed and widely publicized. There followed a series of epoch-making analyses of fallen stones and "native irons" by the chemist Edward C. Howard and the mineralogist Jacques-Louis de Bournon. They showed that all the stones were much alike in texture and composition but significantly different from the Earth's known crustal rocks. Of primary importance was Howard's discovery of nickel in the irons and the metal grains of the stones. This linked the two as belonging to the same natural phenomenon. The chemical results, published in 1802 February, persuaded leading scientists in England, France, and Germany that bodies fall from the sky. Within a few months, chemists in France reported similar results and a new field of study was inaugurated internationally—although opposition lingered on until 1803 April, when nearly 3,000 stones fell at L'Aigle in Normandy and transformed the last skeptics into believers. Chladni immediately received full credit for his hypothesis of falls, but decades passed before his linking of falling bodies with fireballs received general acceptance. His hypothesis of their origin met with strong resistance from those who argued that stones formed within the Earth's atmosphere or were ejected by lunar volcanoes. After 1860, when both of these hypotheses were abandoned, there followed a century of debate between proponents of an interstellar vs. a planetary origin. Not until the 1950s did conclusive evidence of their elliptical orbits establish meteorite parent bodies as members of the solar system. Thus, nearly 200 years passed before the questions of origin that Chladni raised finally were resolved.

Search for promising compositions for developing new multiphase casting alloys based on Al-Cu-Mg matrix using thermodynamic calculations and mathematic simulation

NASA Astrophysics Data System (ADS)

Zolotorevskii, V. S.; Pozdnyakov, A. V.; Churyumov, A. Yu.

2012-11-01

A calculation-experimental study is carried out to improve the concept of searching for new alloying systems in order to develop new casting alloys using mathematical simulation methods in combination with thermodynamic calculations. The results show the high effectiveness of the applied methods. The real possibility of selecting the promising compositions with the required set of casting and mechanical properties is exemplified by alloys with thermally hardened Al-Cu and Al-Cu-Mg matrices, as well as poorly soluble additives that form eutectic components using mainly the calculation study methods and the minimum number of experiments.

Detection of a Pool in Semi-Continuous Castings Made of Heat-Treatable Aluminum Alloys

NASA Astrophysics Data System (ADS)

Krushenko, G. G.; Nazarov, V. P.

2017-12-01

Various products (sheets, sections, etc.) manufactured by metal forming (rolled products, forged pieces, etc.) from semi-continuous castings are widely used in the aerospace industry. The so-called pool, which is the conical volume of a liquid metal, exists at the top of the liquid metal. Experience demonstrates that the geometry, the depth, and the shape of the pool substantially affect the structure formation in a casting and its quality. The application of a titanium nitride nanopowder, which is introduced in a melt in the volume of a rod, as a modifier allowed us to find the exact geometry of the pool.

The influence of cooling parameters on the speed of continuous steel casting

NASA Astrophysics Data System (ADS)

Tirian, G. O.; Gheorghiu, C. A.; Hepuţ, T.; Chioncel, C. P.

2018-01-01

This paper analyzes the cooling parameters of the continuous casting speed. In the researches carried out we aimed to establish some correlation equations between the parameters characterizing the continuous casting process, the temperature of the steel at the entrance to the crystallizer, the superheating of the steel and the flow of the cooling water in the crystallizer and different zones of the secondary cooling. Parallel to these parameters were also the values for the casting speed. The research was made for the casting of round ϕ270mm semi-finished steel products. The steel was developed in an electric EBT furnace with a capacity of 100t, treated in L.F. (Ladle - Furnace) and VD (Vacuum-Degassing) and poured in a 5-wire continuous casting plant. The obtained data was processed in MATLAB using three types of correlation equations. The obtained results are presented both in the analytical and graphical form, each correlation being analyzed from the technological point of view, indicating the optimal values for the independent parameters monitored. In the analysis we present a comparison between the results obtained after the three types of equations for each correlation.