Structural Solutions for Low-Cost Bamboo Frames: Experimental Tests and Constructive Assessments

PubMed Central

Sassu, Mauro; De Falco, Anna; Giresini, Linda; Puppio, Mario Lucio

2016-01-01

Experimental tests and constructive assessments are presented for a simple bamboo framed structure with innovative low-cost and low technology joints, specifically conceived for small buildings in developing countries. Two full scale one-storey bamboo frames have been designed by using the simplest joints solution among three different tested typologies. The entire building process is based on low-technology and natural materials: bamboo canes, wooden cylinders, plywood plates and canapé rods. The first full scale specimen (Unit A) is a one-storey single deck truss structure subjected to monotonic collapse test; the second full scale specimen (Unit B) is a one-storey double deck truss structure used to evaluate the construction time throughout assembling tests. The first full scale specimen showed ductility in collapse and ease in strengthening; the second one showed remarkable ease and speed in assembling structural elements. Finally several constructive solutions are suggested for the design of simple one-storey buildings; they are addressed to four purposes (housing, school, chapel, health center) by the composition of the proposed full scale bamboo frames. Ease of use and maintenance with a low level of technology contribute to application in developing countries although not exclusively. PMID:28773472

An Experimental Investigation on the Ultimate Strength of Partially Infilled: Braced Steel Frames

NASA Astrophysics Data System (ADS)

Dubey, Shailendra Kumar Damodar; Kute, Sunil Y.

2017-12-01

Infilled walls are usually, considered as non-structural elements. However, these walls are effective in carrying lateral loads. In this regard, an experimental investigation was planned and conducted to study the effect of braced and partially infilled steel frames with cement mortar and concrete in comparison to the bare frames. All these frames were tested up to collapse and subjected only to horizontal loads to obtain an effective and possible solution for soft storey which are generally not infilled. In comparison to bare steel frames, partially infilled frames have an increase of lateral load capacity by 45-60%. Central bracing is more effective than that of the corner bracing. For the same load partially infilled frames have significantly less deflection than that of the bare frames. A reduced load factor is suggested for the design of soft storey columns with the partial infills. A mathematical model has been proposed to calculate the theoretical ultimate load for the braced, cement mortar and concrete partial infilled frames.

Subjects, Networks and Positions: Thinking Educational Guidance Differently

ERIC Educational Resources Information Center

Usher, Robin; Edwards, Richard G.

2005-01-01

This article explores the ways in which framings drawn from post-structuralism can help to inform the understanding of guidance practices. In particular, it draws upon the later work of Foucault and Actor-Network Theory to question the centrality of the humanistic subject predominant within discourses of contemporary guidance and raise issues of…

Damage evaluation of reinforced concrete frame based on a combined fiber beam model

NASA Astrophysics Data System (ADS)

Shang, Bing; Liu, ZhanLi; Zhuang, Zhuo

2014-04-01

In order to analyze and simulate the impact collapse or seismic response of the reinforced concrete (RC) structures, a combined fiber beam model is proposed by dividing the cross section of RC beam into concrete fiber and steel fiber. The stress-strain relationship of concrete fiber is based on a model proposed by concrete codes for concrete structures. The stress-strain behavior of steel fiber is based on a model suggested by others. These constitutive models are implemented into a general finite element program ABAQUS through the user defined subroutines to provide effective computational tools for the inelastic analysis of RC frame structures. The fiber model proposed in this paper is validated by comparing with experiment data of the RC column under cyclical lateral loading. The damage evolution of a three-dimension frame subjected to impact loading is also investigated.

The Galileo Orbiter - Command and telemetry subsystems on their way to Jupiter

NASA Astrophysics Data System (ADS)

Erickson, James K.

1990-09-01

An overview is given of the Galileo command and telemetry subsystems, which exemplify the rigid time-synchronized systems required by TDM (time division multiplexing). The spacecraft clock is examined, along with some of the rationale for the development of the clock structure and timing to give a sense of the design imperatives for rigidly synchronized systems. Additional subjects include the structure of the science and engineering frames, emphasizing the subcommutated structure of the engineering frame and its relationship to the spacecraft clock; ground processing for and basic uses of the telemetry; the various message types used to transmit commands to the spacecraft; and the generation processes for the command message types.

Queer Outings: Uncomfortable Stories about the Subjects of Post-Structural School Ethnography

ERIC Educational Resources Information Center

Youdell, Deborah

2010-01-01

In this paper, I consider the abiding value as well as the limits of queer; navigating the contradictions of a politics and ethnographic practice based on a refutation of an abiding subject; resisting subjectivation and needing recognition; and "coming out" in school ethnography framed by queer theory. The paper moves from the work of Michel…

Analysis of 3D face forms for proper sizing and CAD of spectacle frames.

PubMed

Kouchi, Makiko; Mochimaru, Masaaki

2004-11-01

Three-dimensional morphological variations in the human face were analysed using digital models of the human face, and the usefulness of such analysis in designing industrial products was demonstrated by validating spectacle frame designs based on an original sizing system developed based on the analysis. A normalized model of the three-dimensional face form was made for each of 56 young adult Japanese males. The morphological distances between subjects were defined, and subjects were divided into four groups based on analysis of the distance matrix. A prototype spectacle frame was designed for the average form of each of the four groups. Tightening force of the prototype frames was adjusted using the materialized average forms with soft material placed at the nasal bridge and side of the head. Four prototype frames as well as a conventional frame were evaluated using sensory evaluation and physical measurement of the pressure and slip in 38 young adult male subjects. For each of the 38 subjects, prototype frames were ranked according to the morphological similarity of the subjects and the average form of the four groups: the frame designed for the average form of the group most similar to the subject was #1, the frame designed for the average form of the next most similar group was #2, and so on. For the groups with smaller or narrower faces, new frame #1 was most preferred and had the best overall fit, smallest slip sensation and largest pressure sensation. The groups with larger or wider faces preferred tighter frames than new frame #1, because they were concerned that the frames might slip, although the frames did not. Most of the subjects habitually wore spectacles, and the reason that groups with larger or wider faces preferred tighter frames was thought to be that they were accustomed to tighter fitting frames.

Ultrasound investigation of fetal human upper respiratory anatomy.

PubMed

Wolfson, V P; Laitman, J T

1990-07-01

Although the human upper respiratory-upper digestive tract is an area of vital importance, relatively little is known about either the structural or functional changes that occur in the region during the fetal period. While investigations in our laboratory have begun to chart these changes through the use of postmortem materials, in vivo studies have been rarely attempted. This study combines ultrasonography with new applications of video editing to examine aspects of prenatal upper respiratory development. Structures of the fetal upper respiratory-digestive tract and their movements were studied through the use of ultrasonography and detailed frame-by-frame analysis. Twenty-five living fetuses, aged 18-36 weeks gestation, were studied in utero during routine diagnostic ultrasound examination. These real-time linear array sonograms were videotaped during each study. Videotapes were next analyzed for anatomical structures and movement patterns, played back through the ultrasound machine in normal speed, and then examined with a frame-by-frame video editor (FFVE) to identify structures and movements. Still images were photographed directly from the video monitor using a 35 mm camera. Results show that upper respiratory and digestive structures, as well as their movements, could be seen clearly during normal speed and repeat frame-by-frame analysis. Major structures that could be identified in the majority of subjects included trachea in 20 of 25 fetuses (80%); larynx, 76%; pharynx, 76%. Smaller structures were more variable, but were nevertheless observed on both sagittal and coronal section: piriform sinuses, 76%; thyroid cartilage, 36%; cricoid cartilage, 32%; and epiglottis, 16%. Movements of structures could also be seen and were those typically observed in connection with swallowing: fluttering tongue movements, changes in pharyngeal shape, and passage of a bolus via the piriform sinuses to esophagus. Fetal swallows had minimal laryngeal motion. This study represents the first time that the appearance of upper airway and digestive tract structures have been quantified in conjunction with their movements in the living fetus.

Numerical validation of selected computer programs in nonlinear analysis of steel frame exposed to fire

NASA Astrophysics Data System (ADS)

Maślak, Mariusz; Pazdanowski, Michał; Woźniczka, Piotr

2018-01-01

Validation of fire resistance for the same steel frame bearing structure is performed here using three different numerical models, i.e. a bar one prepared in the SAFIR environment, and two 3D models developed within the framework of Autodesk Simulation Mechanical (ASM) and an alternative one developed in the environment of the Abaqus code. The results of the computer simulations performed are compared with the experimental results obtained previously, in a laboratory fire test, on a structure having the same characteristics and subjected to the same heating regimen. Comparison of the experimental and numerically determined displacement evolution paths for selected nodes of the considered frame during the simulated fire exposure constitutes the basic criterion applied to evaluate the validity of the numerical results obtained. The experimental and numerically determined estimates of critical temperature specific to the considered frame and related to the limit state of bearing capacity in fire have been verified as well.

Bayesian nonlinear structural FE model and seismic input identification for damage assessment of civil structures

NASA Astrophysics Data System (ADS)

Astroza, Rodrigo; Ebrahimian, Hamed; Li, Yong; Conte, Joel P.

2017-09-01

A methodology is proposed to update mechanics-based nonlinear finite element (FE) models of civil structures subjected to unknown input excitation. The approach allows to jointly estimate unknown time-invariant model parameters of a nonlinear FE model of the structure and the unknown time histories of input excitations using spatially-sparse output response measurements recorded during an earthquake event. The unscented Kalman filter, which circumvents the computation of FE response sensitivities with respect to the unknown model parameters and unknown input excitations by using a deterministic sampling approach, is employed as the estimation tool. The use of measurement data obtained from arrays of heterogeneous sensors, including accelerometers, displacement sensors, and strain gauges is investigated. Based on the estimated FE model parameters and input excitations, the updated nonlinear FE model can be interrogated to detect, localize, classify, and assess damage in the structure. Numerically simulated response data of a three-dimensional 4-story 2-by-1 bay steel frame structure with six unknown model parameters subjected to unknown bi-directional horizontal seismic excitation, and a three-dimensional 5-story 2-by-1 bay reinforced concrete frame structure with nine unknown model parameters subjected to unknown bi-directional horizontal seismic excitation are used to illustrate and validate the proposed methodology. The results of the validation studies show the excellent performance and robustness of the proposed algorithm to jointly estimate unknown FE model parameters and unknown input excitations.

Compression Strength of Composite Primary Structural Components

NASA Technical Reports Server (NTRS)

Johnson, Eric R.; Starnes, James H., Jr. (Technical Monitor)

2000-01-01

The focus of research activities under NASA Grant NAG-1-2035 was the response and failure of thin-walled structural components. The research is applicable to the primary load carrying structure of flight vehicles, with particular emphasis on fuselage and wing'structure. Analyses and tests were performed that are applicable to the following structural components an aft pressure bulkhead, or a composite pressure dome, pressure cabin damage containment, and fuselage frames subject to crash-type loads.

The role of knowledge structures in fault diagnosis

NASA Technical Reports Server (NTRS)

Smith, P. J.; Giffin, W. C.; Rockwell, T. H.; Thomas, M. E.

1984-01-01

The use of human memory and knowledge structures to direct fault diagnosis performance was investigated. The performances of 20 pilots with instrument flight ratings were studied in a fault diagnosis task. The pilots were read a scenario which described flight conditions under which the symptoms which are indicative of a problem were detected. They were asked to think out loud as they requested and interpreted various pieces of information to diagnose the cause of the problem. Only 11 of the 20 pilots successfully diagnosed the problem. Pilot performance on this fault diagnosis task was modeled in the use of domain specific knowledge organized in a frame system. Eighteen frames, with a common structure, were necessary to account for the data from all twenty subjects.

Alternative approximation concepts for space frame synthesis

NASA Technical Reports Server (NTRS)

Lust, R. V.; Schmit, L. A.

1985-01-01

A structural synthesis methodology for the minimum mass design of 3-dimensionall frame-truss structures under multiple static loading conditions and subject to limits on displacements, rotations, stresses, local buckling, and element cross-sectional dimensions is presented. A variety of approximation concept options are employed to yield near optimum designs after no more than 10 structural analyses. Available options include: (A) formulation of the nonlinear mathematcal programming problem in either reciprocal section property (RSP) or cross-sectional dimension (CSD) space; (B) two alternative approximate problem structures in each design space; and (C) three distinct assumptions about element end-force variations. Fixed element, design element linking, and temporary constraint deletion features are also included. The solution of each approximate problem, in either its primal or dual form, is obtained using CONMIN, a feasible directions program. The frame-truss synthesis methodology is implemented in the COMPASS computer program and is used to solve a variety of problems. These problems were chosen so that, in addition to exercising the various approximation concepts options, the results could be compared with previously published work.

The neural subjective frame: from bodily signals to perceptual consciousness

PubMed Central

Park, Hyeong-Dong; Tallon-Baudry, Catherine

2014-01-01

The report ‘I saw the stimulus’ operationally defines visual consciousness, but where does the ‘I’ come from? To account for the subjective dimension of perceptual experience, we introduce the concept of the neural subjective frame. The neural subjective frame would be based on the constantly updated neural maps of the internal state of the body and constitute a neural referential from which first person experience can be created. We propose to root the neural subjective frame in the neural representation of visceral information which is transmitted through multiple anatomical pathways to a number of target sites, including posterior insula, ventral anterior cingulate cortex, amygdala and somatosensory cortex. We review existing experimental evidence showing that the processing of external stimuli can interact with visceral function. The neural subjective frame is a low-level building block of subjective experience which is not explicitly experienced by itself which is necessary but not sufficient for perceptual experience. It could also underlie other types of subjective experiences such as self-consciousness and emotional feelings. Because the neural subjective frame is tightly linked to homeostatic regulations involved in vigilance, it could also make a link between state and content consciousness. PMID:24639580

The neural subjective frame: from bodily signals to perceptual consciousness.

PubMed

Park, Hyeong-Dong; Tallon-Baudry, Catherine

2014-05-05

The report 'I saw the stimulus' operationally defines visual consciousness, but where does the 'I' come from? To account for the subjective dimension of perceptual experience, we introduce the concept of the neural subjective frame. The neural subjective frame would be based on the constantly updated neural maps of the internal state of the body and constitute a neural referential from which first person experience can be created. We propose to root the neural subjective frame in the neural representation of visceral information which is transmitted through multiple anatomical pathways to a number of target sites, including posterior insula, ventral anterior cingulate cortex, amygdala and somatosensory cortex. We review existing experimental evidence showing that the processing of external stimuli can interact with visceral function. The neural subjective frame is a low-level building block of subjective experience which is not explicitly experienced by itself which is necessary but not sufficient for perceptual experience. It could also underlie other types of subjective experiences such as self-consciousness and emotional feelings. Because the neural subjective frame is tightly linked to homeostatic regulations involved in vigilance, it could also make a link between state and content consciousness.

Dynamic Shape Reconstruction of Three-Dimensional Frame Structures Using the Inverse Finite Element Method

NASA Technical Reports Server (NTRS)

Gherlone, Marco; Cerracchio, Priscilla; Mattone, Massimiliano; Di Sciuva, Marco; Tessler, Alexander

2011-01-01

A robust and efficient computational method for reconstructing the three-dimensional displacement field of truss, beam, and frame structures, using measured surface-strain data, is presented. Known as shape sensing , this inverse problem has important implications for real-time actuation and control of smart structures, and for monitoring of structural integrity. The present formulation, based on the inverse Finite Element Method (iFEM), uses a least-squares variational principle involving strain measures of Timoshenko theory for stretching, torsion, bending, and transverse shear. Two inverse-frame finite elements are derived using interdependent interpolations whose interior degrees-of-freedom are condensed out at the element level. In addition, relationships between the order of kinematic-element interpolations and the number of required strain gauges are established. As an example problem, a thin-walled, circular cross-section cantilevered beam subjected to harmonic excitations in the presence of structural damping is modeled using iFEM; where, to simulate strain-gauge values and to provide reference displacements, a high-fidelity MSC/NASTRAN shell finite element model is used. Examples of low and high-frequency dynamic motion are analyzed and the solution accuracy examined with respect to various levels of discretization and the number of strain gauges.

Response of a 2-story test-bed structure for the seismic evaluation of nonstructural systems

NASA Astrophysics Data System (ADS)

Soroushian, Siavash; Maragakis, E. "Manos"; Zaghi, Arash E.; Rahmanishamsi, Esmaeel; Itani, Ahmad M.; Pekcan, Gokhan

2016-03-01

A full-scale, two-story, two-by-one bay, steel braced-frame was subjected to a number of unidirectional ground motions using three shake tables at the UNR-NEES site. The test-bed frame was designed to study the seismic performance of nonstructural systems including steel-framed gypsum partition walls, suspended ceilings and fire sprinkler systems. The frame can be configured to perform as an elastic or inelastic system to generate large floor accelerations or large inter story drift, respectively. In this study, the dynamic performance of the linear and nonlinear test-beds was comprehensively studied. The seismic performance of nonstructural systems installed in the linear and nonlinear test-beds were assessed during extreme excitations. In addition, the dynamic interactions of the test-bed and installed nonstructural systems are investigated.

Constructive systems, load-bearing and enclosing structures of high-rise buildings

NASA Astrophysics Data System (ADS)

Anatol'evna Korol', Elena; Olegovna Kustikova, Yuliya

2018-03-01

As the height of the building increases, loads on load-carrying structures increase dramatically, and as a result of the development of high-rise construction, several structural systems of such buildings have been developed: frame, frame-frame, cross-wall, barrel, box-type, box-to-wall ("pipe in pipe", "Trumpet in the farm"), etc. In turn, the barrel systems have their own versions: cantilever support of the ceilings on the trunk, suspension of the outer part of the overlap to the upper carrying console "hanging house" or its support by means of the walls on the lower bearing cantilever, intermediate position of the supporting cantilevers in height to the floor, from a part of floors. The object of the study are the structural solutions of high-rise buildings. The subject of the study is the layout of structural schemes of high-rise buildings, taking into account the main parameters - altitude (height), natural climatic conditions of construction, materials of structural elements and their physical and mechanical characteristics. The purpose of the study is to identify the features and systematization of structural systems of high-rise buildings and the corresponding structural elements. The results of the research make it possible, at the stage of making design decisions, to establish rational parameters for the correspondence between the structural systems of high-rise buildings and their individual elements.

Evaluation of the reproducibility of lung motion probability distribution function (PDF) using dynamic MRI.

PubMed

Cai, Jing; Read, Paul W; Altes, Talissa A; Molloy, Janelle A; Brookeman, James R; Sheng, Ke

2007-01-21

Treatment planning based on probability distribution function (PDF) of patient geometries has been shown a potential off-line strategy to incorporate organ motion, but the application of such approach highly depends upon the reproducibility of the PDF. In this paper, we investigated the dependences of the PDF reproducibility on the imaging acquisition parameters, specifically the scan time and the frame rate. Three healthy subjects underwent a continuous 5 min magnetic resonance (MR) scan in the sagittal plane with a frame rate of approximately 10 f s-1, and the experiments were repeated with an interval of 2 to 3 weeks. A total of nine pulmonary vessels from different lung regions (upper, middle and lower) were tracked and the dependences of their displacement PDF reproducibility were evaluated as a function of scan time and frame rate. As results, the PDF reproducibility error decreased with prolonged scans and appeared to approach equilibrium state in subjects 2 and 3 within the 5 min scan. The PDF accuracy increased in the power function with the increase of frame rate; however, the PDF reproducibility showed less sensitivity to frame rate presumably due to the randomness of breathing which dominates the effects. As the key component of the PDF-based treatment planning, the reproducibility of the PDF affects the dosimetric accuracy substantially. This study provides a reference for acquiring MR-based PDF of structures in the lung.

Damage detection and quantification in a structural model under seismic excitation using time-frequency analysis

NASA Astrophysics Data System (ADS)

Chan, Chun-Kai; Loh, Chin-Hsiung; Wu, Tzu-Hsiu

2015-04-01

In civil engineering, health monitoring and damage detection are typically carry out by using a large amount of sensors. Typically, most methods require global measurements to extract the properties of the structure. However, some sensors, like LVDT, cannot be used due to in situ limitation so that the global deformation remains unknown. An experiment is used to demonstrate the proposed algorithms: a one-story 2-bay reinforce concrete frame under weak and strong seismic excitation. In this paper signal processing techniques and nonlinear identification are used and applied to the response measurements of seismic response of reinforced concrete structures subject to different level of earthquake excitations. Both modal-based and signal-based system identification and feature extraction techniques are used to study the nonlinear inelastic response of RC frame using both input and output response data or output only measurement. From the signal-based damage identification method, which include the enhancement of time-frequency analysis of acceleration responses and the estimation of permanent deformation using directly from acceleration response data. Finally, local deformation measurement from dense optical tractor is also use to quantify the damage of the RC frame structure.

Estimation of cyclic interstory drift capacity of steel framed structures and future applications for seismic design.

PubMed

Bojórquez, Edén; Reyes-Salazar, Alfredo; Ruiz, Sonia E; Terán-Gilmore, Amador

2014-01-01

Several studies have been devoted to calibrate damage indices for steel and reinforced concrete members with the purpose of overcoming some of the shortcomings of the parameters currently used during seismic design. Nevertheless, there is a challenge to study and calibrate the use of such indices for the practical structural evaluation of complex structures. In this paper, an energy-based damage model for multidegree-of-freedom (MDOF) steel framed structures that accounts explicitly for the effects of cumulative plastic deformation demands is used to estimate the cyclic drift capacity of steel structures. To achieve this, seismic hazard curves are used to discuss the limitations of the maximum interstory drift demand as a performance parameter to achieve adequate damage control. Then the concept of cyclic drift capacity, which incorporates information of the influence of cumulative plastic deformation demands, is introduced as an alternative for future applications of seismic design of structures subjected to long duration ground motions.

Estimation of Cyclic Interstory Drift Capacity of Steel Framed Structures and Future Applications for Seismic Design

PubMed Central

Bojórquez, Edén; Reyes-Salazar, Alfredo; Ruiz, Sonia E.; Terán-Gilmore, Amador

2014-01-01

Several studies have been devoted to calibrate damage indices for steel and reinforced concrete members with the purpose of overcoming some of the shortcomings of the parameters currently used during seismic design. Nevertheless, there is a challenge to study and calibrate the use of such indices for the practical structural evaluation of complex structures. In this paper, an energy-based damage model for multidegree-of-freedom (MDOF) steel framed structures that accounts explicitly for the effects of cumulative plastic deformation demands is used to estimate the cyclic drift capacity of steel structures. To achieve this, seismic hazard curves are used to discuss the limitations of the maximum interstory drift demand as a performance parameter to achieve adequate damage control. Then the concept of cyclic drift capacity, which incorporates information of the influence of cumulative plastic deformation demands, is introduced as an alternative for future applications of seismic design of structures subjected to long duration ground motions. PMID:25089288

Structural health monitoring system of soccer arena based on optical sensors

NASA Astrophysics Data System (ADS)

Shishkin, Victor V.; Churin, Alexey E.; Kharenko, Denis S.; Zheleznova, Maria A.; Shelemba, Ivan S.

2014-05-01

A structural health monitoring system based on optical sensors has been developed and installed on the indoor soccer arena "Zarya" in Novosibirsk. The system integrates 119 fiber optic sensors: 85 strain, 32 temperature and 2 displacement sensors. In addition, total station is used for measuring displacement in 45 control points. All of the constituents of the supporting structure are subjects for monitoring: long-span frames with under floor ties, connections, purlins and foundation.

The effect of message framing on breast self-examination attitudes, intentions, and behavior.

PubMed

Meyerowitz, B E; Chaiken, S

1987-03-01

In this study we tested the framing hypothesis that a pamphlet stressing the negative consequences of not performing breast self-examination (BSE) would be more persuasive than a pamphlet emphasizing BSE's positive consequences. College-aged female subjects were exposed to a loss-frame pamphlet, a gain-frame pamphlet, or a no-arguments pamphlet, or they received no pamphlet describing the importance of and the techniques for performing BSE. Attitudes toward BSE and intentions to perform BSE were assessed immediately after this intervention and again 4 months later. The follow-up also assessed subjects' postexperimental BSE behavior. Consistent with predictions, subjects who read a pamphlet with arguments framed in loss language manifested more positive BSE attitudes, intentions, and behaviors than did subjects in the other three conditions. The greater impact of the loss pamphlet could not be attributed to greater fear arousal, better memory for pamphlet content, greater perceived susceptibility to breast cancer, or stronger beliefs in BSE's efficacy on the part of the loss subjects. Only measures of perceived self-efficacy in performing BSE were differentially affected by the framing manipulation, with loss subjects reporting the greatest levels of self-confidence. The results are discussed in terms of prospect theory's framing postulate and a simpler negativity-bias conceptualization, and underlying mechanisms such as differential salience and vividness are considered. Clinical implications of the findings are also explored.

The moderating role of objective and subjective numeracy in attribute framing.

PubMed

Gamliel, Eyal; Kreiner, Hamutal; Garcia-Retamero, Rocio

2016-04-01

Previous research has found that objective numeracy moderates framing effects: People who are less numerate were found to be more susceptible to goal-framing and attribute-framing effects than people who are highly numerate. This study examined the possibility that subjective numeracy likewise moderates attribute framing in contexts where participants are presented with percentages of success or failure. The results show that compared with highly numerate participants, less numerate participants were more susceptible to the effect of attribute framing. Interestingly, this moderating effect was revealed only when using objective numeracy measures, and not when subjective numeracy measures were used. Future research is suggested to replicate these findings, to establish the generalizability of numeracy as a moderator of other cognitive biases, and to examine several possible theoretical explanations for the differential moderation of attribute-framing bias. © 2015 International Union of Psychological Science.

Framing effects in choices between multioutcome life-expectancy lotteries.

PubMed

Bernstein, L M; Chapman, G B; Elstein, A S

1999-01-01

To explore framing or editing effects and a method to debias framing in a clinical context. Clinical scenarios using multioutcome life-expectancy lotteries of equal value required choices between two supplementary drugs that either prolonged or shortened life from the 20-year beneficial effect of a baseline drug. The effects of these supplementary drugs were presented in two conditions, using a between-subjects design. In segregated editing (n = 116) the effects were presented separately from the effects of the baseline drug. In integrated editing (n = 100), effects of supplementary and baseline drugs were combined in the lottery presentation. Each subject responded to 30 problems. To explore one method of debiasing, another 100 subjects made choices after viewing both segregated and integrated editings of 20 problems (dual framing). Statistically significant preference reversals between segregated and integrated editing of pure lotteries occurred only when one framing placed outcomes in the gain domain, and the other framing placed them in the loss domain. When both editings resulted in gain-domain outcomes only, there was no framing effect. There was a related relationship of framing-effect shifts from losses to gains in mixed-lottery-choice problems. Responses to the dual framing condition did not consistently coincide with responses to either single framing. In some situations, dual framing eliminated or lessened framing effects. The results support two components of prospect theory, coding outcomes as gains or losses from a reference point, and an s-shaped utility function (concave in gain, convex in loss domains). Presenting both alternative editings of a complex situation prior to choice more fully informs the decision maker and may help to reduce framing effects. Given the extent to which preferences shift in response to alternative presentations, it is unclear which choice represents the subject's "true preferences."

In-Plane Behaviour of a Reinforcement Concrete Frame with a Dry Stack Masonry Panel

PubMed Central

Lin, Kun; Totoev, Yuri Zarevich; Liu, Hongjun; Guo, Tianyou

2016-01-01

In order to improve the energy dissipation of the masonry infilled frame structure while decreasing the stiffening and strengthening effects of the infill panels, a new dry stacked panel (DSP) semi-interlocking masonry (SIM) infill panel has been developed. In this paper, the material properties of DSP and a traditional unreinforced masonry (URM) panel have been evaluated experimentally. A series of cyclic tests were performed to investigate the cyclic behaviour of the reinforcement concrete (RC) frame with different infill panels. The failure modes, damage evolution, hysteretic behaviour, stiffness degradation and energy dissipation were compared and analysed. We concluded that DSP is capable of significantly improving the seismic energy dissipation due to its hysteretic behaviour when the frame is in elastic stage without increasing the stiffness of the frame. Therefore, DSP or SIM panels can be considered as frictional dampers. Based on the experimental results, the influence of DSP was examined. Using the parallel model, the hysteretic loops of DSP subjected to different load cases were achieved. The typical full hysteretic loop for DSP could be divided into three distinct stages of behaviour: packing stage, constant friction stage and equivalent strut stage. The connection between the panel and the frame had a great effect on the transferring of different mechanical stages. The constant friction stage was verified to provide substantial energy dissipation and benefits to the ductility of the structure, which, therefore, is suggested to be prolonged in reality. PMID:28787906

In-Plane Behaviour of a Reinforcement Concrete Frame with a Dry Stack Masonry Panel.

PubMed

Lin, Kun; Totoev, Yuri Zarevich; Liu, Hongjun; Guo, Tianyou

2016-02-11

In order to improve the energy dissipation of the masonry infilled frame structure while decreasing the stiffening and strengthening effects of the infill panels, a new dry stacked panel (DSP) semi-interlocking masonry (SIM) infill panel has been developed. In this paper, the material properties of DSP and a traditional unreinforced masonry (URM) panel have been evaluated experimentally. A series of cyclic tests were performed to investigate the cyclic behaviour of the reinforcement concrete (RC) frame with different infill panels. The failure modes, damage evolution, hysteretic behaviour, stiffness degradation and energy dissipation were compared and analysed. We concluded that DSP is capable of significantly improving the seismic energy dissipation due to its hysteretic behaviour when the frame is in elastic stage without increasing the stiffness of the frame. Therefore, DSP or SIM panels can be considered as frictional dampers. Based on the experimental results, the influence of DSP was examined. Using the parallel model, the hysteretic loops of DSP subjected to different load cases were achieved. The typical full hysteretic loop for DSP could be divided into three distinct stages of behaviour: packing stage, constant friction stage and equivalent strut stage. The connection between the panel and the frame had a great effect on the transferring of different mechanical stages. The constant friction stage was verified to provide substantial energy dissipation and benefits to the ductility of the structure, which, therefore, is suggested to be prolonged in reality.

Structure and strategy in encoding simplified graphs

NASA Technical Reports Server (NTRS)

Schiano, Diane J.; Tversky, Barbara

1992-01-01

Tversky and Schiano (1989) found a systematic bias toward the 45-deg line in memory for the slopes of identical lines when embedded in graphs, but not in maps, suggesting the use of a cognitive reference frame specifically for encoding meaningful graphs. The present experiments explore this issue further using the linear configurations alone as stimuli. Experiments 1 and 2 demonstrate that perception and immediate memory for the slope of a test line within orthogonal 'axes' are predictable from purely structural considerations. In Experiments 3 and 4, subjects were instructed to use a diagonal-reference strategy in viewing the stimuli, which were described as 'graphs' only in Experiment 3. Results for both studies showed the diagonal bias previously found only for graphs. This pattern provides converging evidence for the diagonal as a cognitive reference frame in encoding linear graphs, and demonstrates that even in highly simplified displays, strategic factors can produce encoding biases not predictable solely from stimulus structure alone.

Aftershock collapse vulnerability assessment of reinforced concrete frame structures

USGS Publications Warehouse

Raghunandan, Meera; Liel, Abbie B.; Luco, Nicolas

2015-01-01

In a seismically active region, structures may be subjected to multiple earthquakes, due to mainshock–aftershock phenomena or other sequences, leaving no time for repair or retrofit between the events. This study quantifies the aftershock vulnerability of four modern ductile reinforced concrete (RC) framed buildings in California by conducting incremental dynamic analysis of nonlinear MDOF analytical models. Based on the nonlinear dynamic analysis results, collapse and damage fragility curves are generated for intact and damaged buildings. If the building is not severely damaged in the mainshock, its collapse capacity is unaffected in the aftershock. However, if the building is extensively damaged in the mainshock, there is a significant reduction in its collapse capacity in the aftershock. For example, if an RC frame experiences 4% or more interstory drift in the mainshock, the median capacity to resist aftershock shaking is reduced by about 40%. The study also evaluates the effectiveness of different measures of physical damage observed in the mainshock-damaged buildings for predicting the reduction in collapse capacity of the damaged building in subsequent aftershocks. These physical damage indicators for the building are chosen such that they quantify the qualitative red tagging (unsafe for occupation) criteria employed in post-earthquake evaluation of RC frames. The results indicated that damage indicators related to the drift experienced by the damaged building best predicted the reduced aftershock collapse capacities for these ductile structures.

Engineering Aid 3 & 2, Vol. 2. Rate Training Manual.

ERIC Educational Resources Information Center

Bernal, Benito C., Jr.

Designed for individual study and not formal classroom instruction, this rate training manual provides subject matter that relates directly to the occupational qualifications of the Engineering Aid (EA) rating. This volume contains 10 chapters which deal with: (1) wood and light frame structures (examining the uses, kinds, sizes, and grades of…

Retrofit of hollow concrete masonry infilled steel frames using glass fiber reinforced plastic laminates

NASA Astrophysics Data System (ADS)

Hakam, Zeyad Hamed-Ramzy

2000-11-01

This study focuses on the retrofit of hollow concrete masonry infilled steel frames subjected to in-plane lateral loads using glass fiber reinforced plastic (GFRP) laminates that are epoxy-bonded to the exterior faces of the infill walls. An extensive experimental investigation using one-third scale modeling was conducted and consisted of two phases. In the first phase, 64 assemblages, half of which were retrofitted, were tested under various combined in-plane loading conditions similar to those which different regions of a typical infill wall are subjected to. In the second phase, one bare and four masonry-infilled steel frames representative of a typical single-story, single-bay panel were tested under diagonal loading to study the overall behavior and the infill-frame interaction. The relative infill-to-frame stiffness was varied as a test parameter by using two different steel frame sections. The laminates altered the failure modes of the masonry assemblages and reduced the variability and anisotropic nature of the masonry. For the prisms which failed due to shear and/or mortar joint slip, significant strength increases were observed. For those exhibiting compression failure modes, a marginal increase in strength resulted. Retrofitting the infilled frames resulted in an average increase in initial stiffness of two-fold compared to the unretrofitted infilled frames, and seemed independent of the relative infill-to-frame stiffness. However, the increase in the load-carrying capacity of the retrofitted frames compared to the unretrofitted counterparts was higher for those with the larger relative infill-to-frame stiffness parameter. Unlike the unretrofitted infill walls, the retrofitted panels demonstrated almost identical failure modes that were characterized as "strictly comer crushing" in the vicinity of the loaded comers whereas no signs of distress were evident throughout the remainder of the infill. The laminates also maintained the structural integrity of the infill and prevented collapse and debris fallout even at severe loading stages. A finite element macromodel was proposed for the analysis of the GFRP-retrofitted masonry infilled frames. The infill panel was replaced with a nonlinear, compression-only, diagonal strut. This model was verified using the experimental results of the infilled frame testing and is characterized by its ease of application and accuracy.

Simulating the Impact Response of Full-Scale Composite Airframe Structures

NASA Technical Reports Server (NTRS)

Fasanella, Edwin L.; Jackson, Karen E.; Littell, Justin D.; Seal, Michael D.

2012-01-01

NASA Langley Research Center obtained a composite helicopter cabin structure in 2010 from the US Army's Survivable Affordable Repairable Airframe Program (SARAP) that was fabricated by Sikorsky Aircraft Corporation. The cabin had been subjected to a vertical drop test in 2008 to evaluate a tilting roof concept to limit the intrusion of overhead masses into the fuselage cabin. Damage to the cabin test article was limited primarily to the roof. Consequently, the roof area was removed and the remaining structure was cut into test specimens including a large subfloor section and a forward framed fuselage section. In 2011, NASA and Sikorsky entered into a cooperative research agreement to study the impact responses of composite airframe structures and to evaluate the capabilities of the explicit transient dynamic finite element code, LS-DYNA®, to simulate these responses including damage initiation and progressive failure. Most of the test articles were manufactured of graphite unidirectional tape composite with a thermoplastic resin system. However, the framed fuselage section was constructed primarily of a plain weave graphite fabric material with a thermoset resin system. Test data were collected from accelerometers and full-field photogrammetry. The focus of this paper will be to document impact testing and simulation results for the longitudinal impact of the subfloor section and the vertical drop test of the forward framed fuselage section.

Network-based H.264/AVC whole frame loss visibility model and frame dropping methods.

PubMed

Chang, Yueh-Lun; Lin, Ting-Lan; Cosman, Pamela C

2012-08-01

We examine the visual effect of whole frame loss by different decoders. Whole frame losses are introduced in H.264/AVC compressed videos which are then decoded by two different decoders with different common concealment effects: frame copy and frame interpolation. The videos are seen by human observers who respond to each glitch they spot. We found that about 39% of whole frame losses of B frames are not observed by any of the subjects, and over 58% of the B frame losses are observed by 20% or fewer of the subjects. Using simple predictive features which can be calculated inside a network node with no access to the original video and no pixel level reconstruction of the frame, we developed models which can predict the visibility of whole B frame losses. The models are then used in a router to predict the visual impact of a frame loss and perform intelligent frame dropping to relieve network congestion. Dropping frames based on their visual scores proves superior to random dropping of B frames.

Effects of message framing in anti-binge drinking PSAs: the moderating role of counterfactual thinking.

PubMed

Baek, Tae Hyun; Shen, Lijiang; Reid, Leonard N

2013-01-01

This experiment examined the interaction effects of message framing and counterfactual thinking on attitudes toward binge drinking and behavioral intentions. Data from a 2 (message framing: gain vs. loss) × 2 (counterfactual thinking priming: additive vs. subtractive) between-subjects factorial design showed that a gain-framed message resulted in lower binge drinking intentions than did a loss-framed message after subjects engaged in additive counterfactual thinking. The effects of a loss-framed message on binge drinking intentions occurred when subtractive counterfactual thinking was induced. Theoretical and practical implications for anti-binge drinking public service announcements are discussed.

Fluid-dynamics modelling of the human left ventricle with dynamic mesh for normal and myocardial infarction: preliminary study.

PubMed

Khalafvand, S S; Ng, E Y K; Zhong, L; Hung, T K

2012-08-01

Pulsating blood flow patterns in the left ventricular (LV) were computed for three normal subjects and three patients after myocardial infarction (MI). Cardiac magnetic resonance (MR) images were obtained, segmented and transformed into 25 frames of LV for a computational fluid dynamics (CFD) study. Multi-block structure meshes were generated for 25 frames and 75 intermediate grids. The complete LV cycle was modelled by using ANSYS-CFX 12. The flow patterns and pressure drops in the LV chamber of this study provided some useful information on intra-LV flow patterns with heart diseases. Copyright © 2012 Elsevier Ltd. All rights reserved.

Evaluation of Proposed Electroplated HGU-4/P Frames

DTIC Science & Technology

1975-02-01

READ INSTRUCTIONS BEFORE COMPLE11NG FORII RIECIPII!NT’S CAT AI.OCI NUMBIIR &. TYPE 0,. RIEPOA"T a Pl!lltiOD CoV•t~•o Final I. PERF’OAMINO ORG...rJ Nickel dermatitis Skin reaction Contact dermatitis Aviator frames Nickel-containing frames ZO. ABSTRACT (Contlnu• on rever•• aid• II n•c...Laboratory. Of the 18 subjects who wore the test frames for three months, one subject, an aviator, developed a mild dermatitis along the frontal and

Verification of the Seismic Performance of a Rigidly Connected Modular System Depending on the Shape and Size of the Ceiling Bracket.

PubMed

Lee, Seungjae; Park, Jaeseong; Kwak, Euishin; Shon, Sudeok; Kang, Changhoon; Choi, Hosoon

2017-03-06

Modular systems have been mostly researched in relatively low-rise structures but, lately, their applications to mid- to high-rise structures began to be reviewed, and research interest in new modularization subjects has increased. The application of modular systems to mid- to high-rise structures requires the structural stability of the frame and connections that consist of units, and the evaluation of the stiffness of structures that are combined in units. However, the combination of general units causes loss of the cross-section of columns or beams, resulting in low seismic performance and hindering installation works in the field. In addition, the evaluation of a frame considering such a cross-sectional loss is not easy. Therefore, it is necessary to develop a joint that is stable and easy to install. In the study, a rigidly connected modular system was proposed as a moment-resisting frame for a unit modular system, and their joints were developed and their performances were compared. The proposed system changed the ceiling beam into a bracket type to fasten bolts. It can be merged with other seismic force-resisting systems. To verify the seismic performance of the proposed system, a cyclic loading test was conducted, and the rigidly connected joint performance and integrated behavior at the joint of modular units were investigated. From the experimental results, the maximum resisting force of the proposed connection exceeded the theoretical parameters, indicating that a rigid joint structural performance could be secured.

Updating of visual orientation in a gravity-based reference frame.

PubMed

Niehof, Nynke; Tramper, Julian J; Doeller, Christian F; Medendorp, W Pieter

2017-10-01

The brain can use multiple reference frames to code line orientation, including head-, object-, and gravity-centered references. If these frames change orientation, their representations must be updated to keep register with actual line orientation. We tested this internal updating during head rotation in roll, exploiting the rod-and-frame effect: The illusory tilt of a vertical line surrounded by a tilted visual frame. If line orientation is stored relative to gravity, these distortions should also affect the updating process. Alternatively, if coding is head- or frame-centered, updating errors should be related to the changes in their orientation. Ten subjects were instructed to memorize the orientation of a briefly flashed line, surrounded by a tilted visual frame, then rotate their head, and subsequently judge the orientation of a second line relative to the memorized first while the frame was upright. Results showed that updating errors were mostly related to the amount of subjective distortion of gravity at both the initial and final head orientation, rather than to the amount of intervening head rotation. In some subjects, a smaller part of the updating error was also related to the change of visual frame orientation. We conclude that the brain relies primarily on a gravity-based reference to remember line orientation during head roll.

Smart hybrid rotary damper

NASA Astrophysics Data System (ADS)

Yang, C. S. Walter; DesRoches, Reginald

2014-03-01

This paper develops a smart hybrid rotary damper using a re-centering smart shape memory alloy (SMA) material as well as conventional energy-dissipating metallic plates that are easy to be replaced. The ends of the SMA and steel plates are inserted in the hinge. When the damper rotates, all the plates bend, providing energy dissipating and recentering characteristics. Such smart hybrid rotary dampers can be installed in structures to mitigate structural responses and to re-center automatically. The damaged energy-dissipating plates can be easily replaced promptly after an external excitation, reducing repair time and costs. An OpenSEES model of a smart hybrid rotary was established and calibrated to reproduce the realistic behavior measured from a full-scale experimental test. Furthermore, the seismic performance of a 3-story moment resisting model building with smart hybrid rotary dampers designed for downtown Los Angeles was also evaluated in the OpenSEES structural analysis software. Such a smart moment resisting frame exhibits perfect residual roof displacement, 0.006", extremely smaller than 18.04" for the conventional moment resisting frame subjected to a 2500 year return period ground motion for the downtown LA area (an amplified factor of 1.15 on Kobe earthquake). The smart hybrid rotary dampers are also applied into an eccentric braced steel frame, which combines a moment frame system and a bracing system. The results illustrate that adding smart hybrid rotaries in this braced system not only completely restores the building after an external excitation, but also significantly reduces peak interstory drifts.

Instrument for the application of controlled mechanical loads to tissues in sterile culture

DOEpatents

Lintilhac, Phillip M.; Vesecky, Thompson B.

1995-01-01

Apparatus and methods are disclosed facilitating the application of forces and measurement of dimensions of a test subject. In one arrangement the test subject is coupled to a forcing frame and controlled forces applied thereto by a series of guideways and sliders. The sliders, which contact the test subject are in force transmitting relation to a forcing frame. Tension, compression and bending forces can be applied to the test subject. Force applied to the test subject is measured and controlled. A dimensional characteristic of the test subject, such as growth, is measured by a linear variable differential transformer. The growth measurement data can be used to control the force applied. Substantially uniaxial stretching is achieved by placing the test subject on an elastic membrane stretched by an arrangement of members securing the elastic member to the forcing frame.

Mind the Gap: Physical Education and Health and the Frame Factor Theory as a Tool for Analysing Educational Settings

ERIC Educational Resources Information Center

Lundvall, Suzanne; Meckbach, Jane

2008-01-01

Background: On a normative level as a subject physical education and health seems to adjust rapidly to changes in society, whereas at the practical level it seems receptive to limiting factors such as time, facilities and dominating inherited practices. How can the structuring components and processes relating to the shaping, transformation and…

Impact Testing and Simulation of Composite Airframe Structures

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Littell, Justin D.; Horta, Lucas G.; Annett, Martin S.; Fasanella, Edwin L.; Seal, Michael D., II

2014-01-01

Dynamic tests were performed at NASA Langley Research Center on composite airframe structural components of increasing complexity to evaluate their energy absorption behavior when subjected to impact loading. A second objective was to assess the capabilities of predicting the dynamic response of composite airframe structures, including damage initiation and progression, using a state-of-the-art nonlinear, explicit transient dynamic finite element code, LS-DYNA. The test specimens were extracted from a previously tested composite prototype fuselage section developed and manufactured by Sikorsky Aircraft Corporation under the US Army's Survivable Affordable Repairable Airframe Program (SARAP). Laminate characterization testing was conducted in tension and compression. In addition, dynamic impact tests were performed on several components, including I-beams, T-sections, and cruciform sections. Finally, tests were conducted on two full-scale components including a subfloor section and a framed fuselage section. These tests included a modal vibration and longitudinal impact test of the subfloor section and a quasi-static, modal vibration, and vertical drop test of the framed fuselage section. Most of the test articles were manufactured of graphite unidirectional tape composite with a thermoplastic resin system. However, the framed fuselage section was constructed primarily of a plain weave graphite fabric material with a thermoset resin system. Test data were collected from instrumentation such as accelerometers and strain gages and from full-field photogrammetry.

Development of stiffer and ductile glulam portal frame

NASA Astrophysics Data System (ADS)

Komatsu, Kohei

2017-11-01

Portal frame structures, which are constituted of straight glulam beams and columns connected semi-rigidly by steel insert gusset plate with a lot of drift pins, were the first successful glulam structures widely used in Japan. In addition to this connection system, the author invented also a new type of jointing devise for glulam structures named as "Lagscrewbolt" which had a full threaded portion at inner part to grip wooden member as well as another thread part at the end of shank to connect with other member. The initial type of "Lagscrewbolt" was successfully applied to a various types of glulam buildings which could be rapidly built-up on construction site. Its strength performance, however, was rather brittle therefore the improvement of the ductility was a crucial research subject. In order to give a sufficient ductility on the "Lagscrewbolted joint system", so-called "Slotted Bolted Connection" concept was adopted for making use of large energy dissipation characteristics due to high-tension bolted steel connection with slotted bolt holes. Static & dynamic performance of glulam portal frame specimens was evaluated by static cyclic loading test as well as shaking table test. Current latest form of the jointing system can show very high ductility as well as stable hysteretic cyclic loops by inserting brass-shim between steel-to-steel friction interfaces

Instrument for the application of controlled mechanical loads to tissues in sterile culture

DOEpatents

Lintilhac, P.M.; Vesecky, T.B.

1995-04-18

Apparatus and methods are disclosed facilitating the application of forces and measurement of dimensions of a test subject. In one arrangement the test subject is coupled to a forcing frame and controlled forces applied thereto by a series of guideways and sliders. The sliders, which contact the test subject are in force transmitting relation to a forcing frame. Tension, compression and bending forces can be applied to the test subject. Force applied to the test subject is measured and controlled. A dimensional characteristic of the test subject, such as growth, is measured by a linear variable differential transformer. The growth measurement data can be used to control the force applied. Substantially uniaxial stretching is achieved by placing the test subject on an elastic membrane stretched by an arrangement of members securing the elastic member to the forcing frame. 8 figs.

Expectancy of Success, Subjective Task-Value, and Message Frame in the Appraisal of Value-Promoting Messages Made Prior to a High-Stakes Examination

ERIC Educational Resources Information Center

Putwain, David W.; Symes, Wendy

2016-01-01

Previous research has examined how subjective task-value and expectancy of success influence the appraisal of value-promoting messages used by teachers prior to high-stakes examinations. The aim of this study was to examine whether message-frame (gain or loss-framed messages) also influences the appraisal of value-promoting messages. Two hundred…

A study of video frame rate on the perception of moving imagery detail

NASA Technical Reports Server (NTRS)

Haines, Richard F.; Chuang, Sherry L.

1993-01-01

The rate at which each frame of color moving video imagery is displayed was varied in small steps to determine what is the minimal acceptable frame rate for life scientists viewing white rats within a small enclosure. Two, twenty five second-long scenes (slow and fast animal motions) were evaluated by nine NASA principal investigators and animal care technicians. The mean minimum acceptable frame rate across these subjects was 3.9 fps both for the slow and fast moving animal scenes. The highest single trial frame rate averaged across all subjects for the slow and the fast scene was 6.2 and 4.8, respectively. Further research is called for in which frame rate, image size, and color/gray scale depth are covaried during the same observation period.

Experimental study on the influence of the opening in brick-masonry wall to seismic performance of reinforced concrete frame structures

NASA Astrophysics Data System (ADS)

Maidiawati, Tanjung, Jafril; Medriosa, Hamdeni

2017-10-01

Reinforced concrete (RC) frame structures with brick-masonry infills are commonly used in developing countries and high-risk seismic area, such as Indonesia. Significant researches have been carried out for studying the seismic performance of RC frame structures with brick-masonry infills. Only few of them focused on effects of the opening in the brick-masonry infill to the seismic performance of the RC frame structures. The presence of opening in brick-masonry infill is often used for placing doors and windows as well, however, it may reduce the seismic performance of the RC frame structure. In the current study, they influence of the opening in brick-masonry infills to the seismic performance RC frame structure will experimentally evaluated. Five of 1/4-scaled single story and single bay RC frame specimens were prepared, i.e. an RC bare frame, a clay brick-masonry infilled RC frame and three of clay brick-masonry infilled RC frame with openings in the brick-masonry infills. The last three specimens were clay brick infilled RC frame with a center opening, clay brick infilled RC frame with two openings used for placing the windows and clay brick infilled RC frame with opening for placing the door. The specimens pushed over by applying the static monotonic lateral load to the upper beam of the RC frame structures. The incremental of the lateral load and the lateral displacement of RC frame's column was recorded during test. The crack propagation and the major cracks were also observed to identify the mechanism failure of specimens. As the results, the opening in the brick-masonry wall controls the failure mechanism, the lateral strength and the stiffness of the overall of infilled RC frame structure. The diagonal shear crack pattern was found on brick-masonry wall without opening, on other hand the different crack patterns were observed on brick-masonry wall with openings. Although the opening in the brick masonry infill reduced the lateral strength and stiffness of the infilled RC frame, it was still stronger and stiffer than the bare frame.

Verification of the Seismic Performance of a Rigidly Connected Modular System Depending on the Shape and Size of the Ceiling Bracket

PubMed Central

Lee, Seungjae; Park, Jaeseong; Kwak, Euishin; Shon, Sudeok; Kang, Changhoon; Choi, Hosoon

2017-01-01

Modular systems have been mostly researched in relatively low-rise structures but, lately, their applications to mid- to high-rise structures began to be reviewed, and research interest in new modularization subjects has increased. The application of modular systems to mid- to high-rise structures requires the structural stability of the frame and connections that consist of units, and the evaluation of the stiffness of structures that are combined in units. However, the combination of general units causes loss of the cross-section of columns or beams, resulting in low seismic performance and hindering installation works in the field. In addition, the evaluation of a frame considering such a cross-sectional loss is not easy. Therefore, it is necessary to develop a joint that is stable and easy to install. In the study, a rigidly connected modular system was proposed as a moment-resisting frame for a unit modular system, and their joints were developed and their performances were compared. The proposed system changed the ceiling beam into a bracket type to fasten bolts. It can be merged with other seismic force-resisting systems. To verify the seismic performance of the proposed system, a cyclic loading test was conducted, and the rigidly connected joint performance and integrated behavior at the joint of modular units were investigated. From the experimental results, the maximum resisting force of the proposed connection exceeded the theoretical parameters, indicating that a rigid joint structural performance could be secured. PMID:28772622

Proposed Assessment of Dynamic Resistance of the Existing Industrial Portal Frame Building Structures to the Impact of Mining Tremors

NASA Astrophysics Data System (ADS)

Rusek, Janusz; Kocot, Wojciech

2017-10-01

The article presents the method for assessing dynamic resistance of the existing industrial portal frame building structures subjected to mining tremors. The study was performed on two industrial halls of a reinforced concrete structure and a steel structure. In order to determine the dynamic resistances of these objects, static and dynamic numerical analysis in the FEA environment was carried out. The scope of numerical calculations was adapted to the guidelines contained in the former and current design standards. This allowed to formulate the criteria, on the basis of which the maximum permissible value of the horizontal ground acceleration was obtained, constituting resistance of the analyzed objects. The permissible range of structural behaviour was determined by comparing the effects of load combinations adopted at the design stage with a seismic combination recognized in Eurocode 8. The response spectrum method was used in the field of dynamic analysis, taking into account the guidelines contained in Eurocode 8 and the guidelines of National. Finally, in accordance with the established procedure, calculations were carried out and the results for the two model portal frame buildings of reinforced concrete and steel structures were presented. The results allowed for the comparison of the dynamic resistance of two different types of material and design, and a sensitivity analysis with respect to their constituent bearing elements. The conclusions drawn from these analyses helped to formulate the thesis for the next stage of the research, in which it is expected to analyze a greater number of objects using a parametric approach, in relation to the geometry and material properties.

Blind subjects construct conscious mental images of visual scenes encoded in musical form.

PubMed Central

Cronly-Dillon, J; Persaud, K C; Blore, R

2000-01-01

Blind (previously sighted) subjects are able to analyse, describe and graphically represent a number of high-contrast visual images translated into musical form de novo. We presented musical transforms of a random assortment of photographic images of objects and urban scenes to such subjects, a few of which depicted architectural and other landmarks that may be useful in navigating a route to a particular destination. Our blind subjects were able to use the sound representation to construct a conscious mental image that was revealed by their ability to depict a visual target by drawing it. We noted the similarity between the way the visual system integrates information from successive fixations to form a representation that is stable across eye movements and the way a succession of image frames (encoded in sound) which depict different portions of the image are integrated to form a seamless mental image. Finally, we discuss the profound resemblance between the way a professional musician carries out a structural analysis of a musical composition in order to relate its structure to the perception of musical form and the strategies used by our blind subjects in isolating structural features that collectively reveal the identity of visual form. PMID:11413637

Head motion evaluation and correction for PET scans with 18F-FDG in the Japanese Alzheimer's disease neuroimaging initiative (J-ADNI) multi-center study.

PubMed

Ikari, Yasuhiko; Nishio, Tomoyuki; Makishi, Yoko; Miya, Yukari; Ito, Kengo; Koeppe, Robert A; Senda, Michio

2012-08-01

Head motion during 30-min (six 5-min frames) brain PET scans starting 30 min post-injection of FDG was evaluated together with the effect of post hoc motion correction between frames in J-ADNI multicenter study carried out in 24 PET centers on a total of 172 subjects consisting of 81 normal subjects, 55 mild cognitive impairment (MCI) and 36 mild Alzheimer's disease (AD) patients. Based on the magnitude of the between-frame co-registration parameters, the scans were classified into six levels (A-F) of motion degree. The effect of motion and its correction was evaluated using between-frame variation of the regional FDG uptake values on ROIs placed over cerebral cortical areas. Although AD patients tended to present larger motion (motion level E or F in 22 % of the subjects) than MCI (3 %) and normal (4 %) subjects, unignorable motion was observed in a small number of subjects in the latter groups as well. The between-frame coefficient of variation (SD/mean) was 0.5 % in the frontal, 0.6 % in the parietal and 1.8 % in the posterior cingulate ROI for the scans of motion level 1. The respective values were 1.5, 1.4, and 3.6 % for the scans of motion level F, but reduced by the motion correction to 0.5, 0.4 and 0.8 %, respectively. The motion correction changed the ROI value for the posterior cingulate cortex by 11.6 % in the case of severest motion. Substantial head motion occurs in a fraction of subjects in a multicenter setup which includes PET centers lacking sufficient experience in imaging demented patients. A simple frame-by-frame co-registration technique that can be applied to any PET camera model is effective in correcting for motion and improving quantitative capability.

Individual differences in the ability to identify, select and use appropriate frames of reference for perceptuo-motor control.

PubMed

Isableu, B; Ohlmann, T; Cremieux, J; Vuillerme, N; Amblard, B; Gresty, M A

2010-09-01

The causes of the interindividual differences (IDs) in how we perceive and control spatial orientation are poorly understood. Here, we propose that IDs partly reflect preferred modes of spatial referencing and that these preferences or "styles" are maintained from the level of spatial perception to that of motor control. Two groups of experimental subjects, one with high visual field dependency (FD) and one with marked visual field independency (FI) were identified by the Rod and Frame Test, which identifies relative dependency on a visual frame of reference (VFoR). FD and FI subjects were tasked with standing still in conditions of increasing postural difficulty while visual cues of self-orientation (a visual frame tilted in roll) and self-motion (in stroboscopic illumination) were varied and in darkness to assess visual dependency. Postural stability, overall body orientation and modes of segmental stabilization relative to either external (space) or egocentric (adjacent segments) frames of reference in the roll plane were analysed. We hypothesized that a moderate challenge to balance should enhance subjects' reliance on VFoR, particularly in FD subjects, whereas a substantial challenge should constrain subjects to use a somatic-vestibular based FoR to prevent falling in which case IDs would vanish. The results showed that with increasing difficulty, FD subjects became more unstable and more disoriented shown by larger effects of the tilted visual frame on posture. Furthermore, their preference to coalign body/VFoR coordinate systems lead to greater fixation of the head-trunk articulation and stabilization of the hip in space, whereas the head and trunk remained more stabilized in space with the hip fixed on the leg in FI subjects. These results show that FD subjects have difficulties at identifying and/or adopting a more appropriate FoR based on proprioceptive and vestibular cues to regulate the coalignment of posturo/exocentric FoRs. The FI subjects' resistance in the face of altered VFoR and balance challenge resides in their greater ability to coordinate movement by coaligning body axes with more appropriate FoRs (provided by proprioceptive and vestibular co-variance). Copyright (c) 2010 IBRO. Published by Elsevier Ltd. All rights reserved.

Test Frame for Gravity Offload Systems

NASA Technical Reports Server (NTRS)

Murray, Alexander R.

2005-01-01

Advances in space telescope and aperture technology have created a need to launch larger structures into space. Traditional truss structures will be too heavy and bulky to be effectively used in the next generation of space-based structures. Large deployable structures are a possible solution. By packaging deployable trusses, the cargo volume of these large structures greatly decreases. The ultimate goal is to three dimensionally measure a boom's deployment in simulated microgravity. This project outlines the construction of the test frame that supports a gravity offload system. The test frame is stable enough to hold the gravity offload system and does not interfere with deployment of, or vibrations in, the deployable test boom. The natural frequencies and stability of the frame were engineered in FEMAP. The test frame was developed to have natural frequencies that would not match the first two modes of the deployable beam. The frame was then modeled in Solidworks and constructed. The test frame constructed is a stable base to perform studies on deployable structures.

Numerical analysis and comparison of three types of herringbone frame structure for highway subgrade slopes protection

NASA Astrophysics Data System (ADS)

Nie, Yihua; Tang, Saiqian; Xu, Yang; Mao, Kunli

2018-04-01

In order to obtain mechanical response distribution of herringbone frame structure for highway subgrade slopes protection and select the best structure type, 3D numerical models of three types herringbone frame structure were established and analyzed in finite element software ANSYS. Indoor physical model of soil slope protected by herringbone frame structure was built and mechanical response of the frame structure was measured by loading tests. Numerical results indicate slope foot is the stress most disadvantageous location. Comparative analysis shows that structure composed of mortar rubble base layer and precast concrete blocks paving layer is the best one for resisting deformation and structure with cement mortar base layer and precast concrete blocks paving layer is the best one for being of low stress.

Re-Framing Literacy: Teaching and Learning in English and the Language Arts. Language, Culture, and Teaching Series

ERIC Educational Resources Information Center

Andrews, Richard

2010-01-01

Imaginative and attractive, cutting edge in its conception, this text explicates a model for the integration of language arts and literacy education based on the notion of framing. The act of framing--not frames in themselves--provides a creative and critical approach to English as a subject. "Re-framing Literacy" breaks new ground in the language…

Effect of Moisture Cycling on Mechanical Response of Metal-Plate Connector Joints With and Without an Adhesive Interface

Treesearch

Leslie H. Groom

1995-01-01

Wood trusses are frequently located in light-frame structures where they are subjected to significant shifts in moisture conditions. However, little is known about the effects of moisture cycling of the wood members on the mechanical behavior of metal-plate connector (MPC) joints. Thus, the primary objective of this study was to quantify the effect of wood moisture...

46 CFR 91.40-3 - Drydock examination, internal structural examination, cargo tank internal examination, and...

Code of Federal Regulations, 2010 CFR

2010-10-01

... hull barge with internal framing 1 Double hull barge with external framing 2 Single hull barge with..., ends, and bottoms) when the structural framing is on the internal tank surface. 2 Applicable to double hull tank barges (double sides, ends, and bottoms) when the structural framing is on the external tank...

Research on seismic behavior and filling effect of a new CFT column-CFT beam frame structure

NASA Astrophysics Data System (ADS)

Wang, Ying; Shima, Hiroshi

2009-12-01

Concrete filled-steel tube (CFT) structure is popularly used in practical structures nowadays. Self-compacting concrete (SCC) was employed to construct a new CFT column-CFT beam frame structure (hereinafter cited as new CFT frame structure) in this research. Three specimens, two CFT column-CFT beam joints and one hollow steel column-I beam joint were tested to investigate seismic behavior of the new CFT frame structure. The experimental results showed that SCC can be successfully compacted into the new CFT frame structure joints in the lab, and the joints provided adequate seismic behavior. In order to further assess filling effect of SCC in the long steel tube, scale column-beam subassembly made of acrylics plate was employed and concrete visual model experiment was done. The results showed that the concrete was able to be successfully cast into the subassembly which indicated that the new CFT frame structure is possible to be constructed in the real building.

Research on seismic behavior and filling effect of a new CFT column-CFT beam frame structure

NASA Astrophysics Data System (ADS)

Wang, Ying; Shima, Hiroshi

2010-03-01

Concrete filled-steel tube (CFT) structure is popularly used in practical structures nowadays. Self-compacting concrete (SCC) was employed to construct a new CFT column-CFT beam frame structure (hereinafter cited as new CFT frame structure) in this research. Three specimens, two CFT column-CFT beam joints and one hollow steel column-I beam joint were tested to investigate seismic behavior of the new CFT frame structure. The experimental results showed that SCC can be successfully compacted into the new CFT frame structure joints in the lab, and the joints provided adequate seismic behavior. In order to further assess filling effect of SCC in the long steel tube, scale column-beam subassembly made of acrylics plate was employed and concrete visual model experiment was done. The results showed that the concrete was able to be successfully cast into the subassembly which indicated that the new CFT frame structure is possible to be constructed in the real building.

Effect of gravito-inertial cues on the coding of orientation in pre-attentive vision.

PubMed

Stivalet, P; Marendaz, C; Barraclough, L; Mourareau, C

1995-01-01

To see if the spatial reference frame used by pre-attentive vision is specified in a retino-centered frame or in a reference frame integrating visual and nonvisual information (vestibular and somatosensory), subjects were centrifuged in a non-pendular cabin and were asked to search for a target distinguishable from distractors by difference in orientation (Treisman's "pop-out" paradigm [1]). In a control condition, in which subjects were sitting immobilized but not centrifuged, this task gave an asymmetric search pattern: Search was rapid and pre-attentional except when the target was aligned with the horizontal retinal/head axis, in which case search was slow and attentional (2). Results using a centrifuge showed that slow/serial search patterns were obtained when the target was aligned with the subjective horizontal axis (and not with the horizontal retinal/head axis). These data suggest that a multisensory reference frame is used in pre-attentive vision. The results are interpreted in terms of Riccio and Stoffregen's "ecological theory" of orientation in which the vertical and horizontal axes constitute independent reference frames (3).

Minimum stiffness criteria for ring frame stiffeners of space launch vehicles

NASA Astrophysics Data System (ADS)

Friedrich, Linus; Schröder, Kai-Uwe

2016-12-01

Frame stringer-stiffened shell structures show high load carrying capacity in conjunction with low structural mass and are for this reason frequently used as primary structures of aerospace applications. Due to the great number of design variables, deriving suitable stiffening configurations is a demanding task and needs to be realized using efficient analysis methods. The structural design of ring frame stringer-stiffened shells can be subdivided into two steps. One, the design of a shell section between two ring frames. Two, the structural design of the ring frames such that a general instability mode is avoided. For sizing stringer-stiffened shell sections, several methods were recently developed, but existing ring frame sizing methods are mainly based on empirical relations or on smeared models. These methods do not mandatorily lead to reliable designs and in some cases the lightweight design potential of stiffened shell structures can thus not be exploited. In this paper, the explicit physical behaviour of ring frame stiffeners of space launch vehicles at the onset of panel instability is described using mechanical substitute models. Ring frame stiffeners of a stiffened shell structure are sized applying existing methods and the method suggested in this paper. To verify the suggested method and to demonstrate its potential, geometrically non-linear finite element analyses are performed using detailed finite element models.

Frame junction vibration transmission with a modified frame deformation model.

PubMed

Moore, J A

1990-12-01

A previous paper dealt with vibration transmission through junctions of connected frame members where the allowed frame deformations included bending, torsion, and longitudinal motions [J.A. Moore, J. Acoust. Soc. Am. 88, 2766-2776 (1990)]. In helicopter and aircraft structures the skin panels can constitute a high impedance connection along the length of the frames that effectively prohibits in-plane motion at the elevation of the skin panels. This has the effect of coupling in-plane bending and torsional motions within the frame. This paper discusses the transmission behavior through frame junctions that accounts for the in-plane constraint in idealized form by assuming that the attached skin panels completely prohibit inplane motion in the frames. Also, transverse shear deformation is accounted for in describing the relatively deep web frame constructions common in aircraft structures. Longitudinal motion in the frames is not included in the model. Transmission coefficient predictions again show the importance of out-of-plane bending deformation to the transmission of vibratory energy in an aircraft structure. Comparisons are shown with measured vibration transmission data along the framing in the overhead of a helicopter airframe, with good agreement. The frame junction description has been implemented within a general purpose statistical energy analysis (SEA) computer code in modeling the entire airframe structure including skin panels.

Analysis of frame structure of medium and small truck crane

NASA Astrophysics Data System (ADS)

Cao, Fuyi; Li, Jinlong; Cui, Mengkai

2018-03-01

Truck crane is an important part of hoisting machinery. Frame, as the support component of the quality of truck crane, determines the safety of crane jib load and the rationality of structural design. In this paper, the truck crane frame is a box structure, the three-dimensional model is established in CATIA software, and imported into Hyperworks software for finite element analysis. On the base of doing constraints and loads for the finite element model of the frame, the finite element static analysis is carried out. And the static stress test verifies whether the finite element model and the frame structure design are reasonable; then the free modal analysis of the frame and the analysis of the first 8 - order modal vibration deformation are carried out. The analysis results show that the maximum stress value of the frame is greater than the yield limit value of the material, and the low-order modal value is close to the excitation frequency value, which needs to be improved to provide theoretical reference for the structural design of the truck crane frame.

Computer modeling and simulation analysis of bearing capacity after reinforcement of underground frame structure

NASA Astrophysics Data System (ADS)

Dai, Yan

2018-04-01

With the increasing development of urban scale, the application of the underground frame structure is becoming more and more extensive. But because of the unreasonable setup, it hinders public transportation. Therefore, it is an effective solution to reinforce the underground frame structure and make it bear the traffic load. The simulation calculation of the reinforced underground frame structure is carried out in this paper. The conclusion is obtained that the structure satisfies the load of vehicle and the load of the crowd.

Wing walls for enhancing the seismic performance of reinforced concrete frame structures

NASA Astrophysics Data System (ADS)

Yang, Weisong; Guo, Xun; Xu, Weixiao; Yuan, Xin

2016-06-01

A building retrofitted with wing walls in the bottom story, which was damaged during the 2008 M8.0 Wenchuan earthquake in China, is introduced and a corresponding 1/4 scale wing wall-frame model was subjected to shake table motions to study the seismic behavior of this retrofitted structural system. The results show that wing walls can effectively protect columns from damage by moving areas that bear reciprocating tension and compression to the sections of the wing walls, thus achieving an extra measure of seismic fortification. A `strong column-weak beam' mechanism was realized, the flexural rigidity of the vertical member was strengthened, and a more uniform distribution of deformation among all the stories was measured. In addition, the joint between the wing walls and the beams suffered severe damage during the tests, due to an area of local stress concentration. A longer area of intensive stirrup is suggested in the end of the beams.

Telemetry Standards, RCC Standard 106-17, Chapter 4, Pulse Code Modulation Standards

DTIC Science & Technology

2017-07-01

Frame Structure .............................................................................................. 4-6 4.3.3 Cyclic Redundancy Check (Class...Spectral and BEP Comparisons for NRZ and Bi-phase............................................ A-3 A.4. PCM Frame Structure Examples...4-4 Figure 4-3. PCM Frame Structure .......................................................................................... 4-6

Message framing strategies to increase influenza immunization uptake among pregnant African American women.

PubMed

Marsh, Heather A; Malik, Fauzia; Shapiro, Eve; Omer, Saad B; Frew, Paula M

2014-09-01

We explored the attitudes, opinions, and concerns of African American women regarding influenza vaccination during pregnancy. As influenza immunization coverage rates remain suboptimal in the United States among this population, we elicited message framing strategies for multicomponent interventions aimed at decreasing future incident cases of maternal and neonatal influenza. Semi-structured in-depth interviews (N = 21) were conducted with pregnant African American women at urban OB/GYN clinics who had not received an influenza vaccine. Interviews were transcribed, subjected to intercoder reliability assessment, and content analyzed to identify common thematic factors related to acceptance of the influenza vaccine and health communication message preferences. Four major themes were identified. These were communication approaches, normal vaccine behavior, pregnancy vaccination, and positive versus negative framing. Two strong themes emerged: positively-framed messages were preferred over negatively-framed messages and those emphasizing the health of the infant. Additionally, previous immunization, message source, and vaccine misperceptions also played important roles in decision-making. The majority of women indicated that positively framed messages focusing on the infant's health would encourage them to receive an influenza vaccine. Messages emphasizing immunization benefits such as protection against preterm birth and low birth weight outcomes have potential to overcome widespread negative community perceptions and cultural beliefs. Additionally, messages transmitted via interpersonal networks and social media strongly influence motivation to obtain vaccination during pregnancy. The findings of this study will assist in developing tailored messages that change pregnant African American women's influenza vaccination decision-making to achieve improved coverage.

Effectiveness of two conventional methods for seismic retrofit of steel and RC moment resisting frames based on damage control criteria

NASA Astrophysics Data System (ADS)

Beheshti Aval, Seyed Bahram; Kouhestani, Hamed Sadegh; Mottaghi, Lida

2017-07-01

This study investigates the efficiency of two types of rehabilitation methods based on economic justification that can lead to logical decision making between the retrofitting schemes. Among various rehabilitation methods, concentric chevron bracing (CCB) and cylindrical friction damper (CFD) were selected. The performance assessment procedure of the frames is divided into two distinct phases. First, the limit state probabilities of the structures before and after rehabilitation are investigated. In the second phase, the seismic risk of structures in terms of life safety and financial losses (decision variables) using the recently published FEMA P58 methodology is evaluated. The results show that the proposed retrofitting methods improve the serviceability and life safety performance levels of steel and RC structures at different rates when subjected to earthquake loads. Moreover, these procedures reveal that financial losses are greatly decreased, and were more tangible by the application of CFD rather than using CCB. Although using both retrofitting methods reduced damage state probabilities, incorporation of a site-specific seismic hazard curve to evaluate mean annual occurrence frequency at the collapse prevention limit state caused unexpected results to be obtained. Contrary to CFD, the collapse probability of the structures retrofitted with CCB increased when compared with the primary structures.

Nonlinear analysis of r.c. framed buildings retrofitted with elastomeric and friction bearings under near-fault earthquakes

NASA Astrophysics Data System (ADS)

Mazza, Mirko

2015-12-01

Reinforced concrete (r.c.) framed buildings designed in compliance with inadequate seismic classifications and code provisions present in many cases a high vulnerability and need to be retrofitted. To this end, the insertion of a base isolation system allows a considerable reduction of the seismic loads transmitted to the superstructure. However, strong near-fault ground motions, which are characterised by long-duration horizontal pulses, may amplify the inelastic response of the superstructure and induce a failure of the isolation system. The above considerations point out the importance of checking the effectiveness of different isolation systems for retrofitting a r.c. framed structure. For this purpose, a numerical investigation is carried out with reference to a six-storey r.c. framed building, which, primarily designed (as to be a fixed-base one) in compliance with the previous Italian code (DM96) for a medium-risk seismic zone, has to be retrofitted by insertion of an isolation system at the base for attaining performance levels imposed by the current Italian code (NTC08) in a high-risk seismic zone. Besides the (fixed-base) original structure, three cases of base isolation are studied: elastomeric bearings acting alone (e.g. HDLRBs); in-parallel combination of elastomeric and friction bearings (e.g. high-damping-laminated-rubber bearings, HDLRBs and steel-PTFE sliding bearings, SBs); friction bearings acting alone (e.g. friction pendulum bearings, FPBs). The nonlinear analysis of the fixed-base and base-isolated structures subjected to horizontal components of near-fault ground motions is performed for checking plastic conditions at the potential critical (end) sections of the girders and columns as well as critical conditions of the isolation systems. Unexpected high values of ductility demand are highlighted at the lower floors of all base-isolated structures, while re-centring problems of the base isolation systems under near-fault earthquakes are expected in case of friction bearings acting alone (i.e. FPBs) or that in combination (i.e. SBs) with HDLRBs.

Study on Detailing Design of Precast Concrete Frame Structure

NASA Astrophysics Data System (ADS)

Lida, Tian; Liming, Li; Kang, Liu; Jiao, Geng; Ming, Li

2018-03-01

Taking a certain precast concrete frame structure as an example, this paper introduces the general procedures and key points in detailing design of emulative cast-in-place prefabricated structure from the aspects of structural scheme, precast element layout, shop drawing design and BIM 3D modelling. This paper gives a practical solution for the detailing design of precast concrete frame structure under structural design codes in China.

Structural Analysis of the QCM Aboard the ER-2

NASA Technical Reports Server (NTRS)

Jones, Phyllis D.; Bainum, Peter M.; Xing, Guangqian

1997-01-01

As a result of recent supersonic transport (SST) studies on the effect they may have on the atmosphere, several experiments have been proposed to capture and evaluate samples of the stratosphere where SST's travel. One means to achieve this is to utilize the quartz crystal microbalance (QCM) installed aboard the ER-2, formerly the U-2 reconnaissance aircraft. The QCM is a cascade impactor designed to perform in-situ, real-time measurements of aerosols and chemical vapors at an altitude of 60,000 - 70,000 feet. The ER-2 is primarily used by NASA for Earth resources to test new sensor systems before they are placed aboard satellites. One of the main reasons the ER-2 is used for this flight experiment is its capability to fly approximately twelve miles above sea level (can reach an altitude of 78,000 feet). Because the ER-2 operates at such a high altitude, it is of special interest to scientists interested in space exploration or supersonic aircraft. Some of the experiments are designed to extract data from the atmosphere around the ER-2. For the current flight experiment, the QCM is housed in a frame that is connected to an outer pod that is attached to the fuselage of the ER-2. Due to the location of the QCM within the housing frame and the location of the pod on the ER-2, the pod and its contents are subject to structural loads. In addition to structural loads, structural vibrations are also of importance because the QCM is a frequency induced instrument. Therefore, a structural analysis of the instrument within the frame is imperative to determine if resonance and/or undesirable deformations occur.

Message framing and perinatal decisions.

PubMed

Haward, Marlyse F; Murphy, Ryan O; Lorenz, John M

2008-07-01

The purpose of this study was to explore the effect of information framing on parental decisions about resuscitation of extremely premature infants. Secondary outcomes focused on elucidating the impact of other variables on treatment choices and determining whether those effects would take precedence over any framing effects. This confidential survey study was administered to adult volunteers via the Internet. The surveys depicted a hypothetical vignette of a threatened delivery at gestational age of 23 weeks, with prognostic outcome information framed as either survival with lack of disability (positive frame) or chance of dying and likelihood of disability among survivors (negative frame). Participants were randomly assigned to receive either the positively or negatively framed vignette. They were then asked to choose whether they would prefer resuscitation or comfort care. After completing the survey vignette, participants were directed to a questionnaire designed to test the secondary hypothesis and to explore possible factors associated with treatment decisions. A total of 146 subjects received prognostic information framed as survival data and 146 subjects received prognostic information framed as mortality data. Overall, 24% of the sample population chose comfort care and 76% chose resuscitation. A strong trend was detected toward a framing effect on treatment preference; respondents for whom prognosis was framed as survival data were more likely to elect resuscitation. This framing effect was significant in a multivariate analysis controlling for religiousness, parental status, and beliefs regarding the sanctity of life. Of these covariates, only religiousness modified susceptibility to framing; participants who were not highly religious were significantly more likely to be influenced to opt for resuscitation by the positive frame than were participants who were highly religious. Framing bias may compromise efforts to approach prenatal counseling in a nondirective manner. This is especially true for subsets of participants who are not highly religious.

On the modal characteristics of damaging structures subjected to earthquakes

NASA Astrophysics Data System (ADS)

Carlo Ponzo, Felice; Ditommaso, Rocco; Auletta, Gianluca; Iacovino, Chiara; Mossucca, Antonello; Nigro, Antonella; Nigro, Domenico

2015-04-01

Structural Health Monitoring, especially for structures located in seismic prone areas, has assumed a meaning of great importance in last years, for the possibility to make a more objective and more rapid estimation of the damage occurred on buildings after a seismic event. In the last years many researchers are working to set-up new methodologies for Non-destructive Damage Evaluation based on the variation of the dynamic behaviour of structures under seismic loads. The NDE methods for damage detection and evaluation can be classified into four levels, according to the specific criteria provided by the Rytter. Each level of identification is correlated with specific information related to monitored structure. In fact, by increasing the level it is possible to obtain more information about the state of the health of the structures, to know if damage occurred on the structures, to quantify and localize the damage and to evaluate its impact on the monitored structure. Several authors discussed on the possibility to use the mode shape curvature to localize damage on structural elements, for example, by applying the curvature-based method to frequency response function instead of mode shape, and demonstrated the potential of this approach by considering real data. Damage detection approach based on dynamic monitoring of structural properties over time has received a considerable attention in recent scientific literature. In earthquake engineering field, the recourse to experimental research is necessary to understand the mechanical behaviour of the various structural and non-structural components. In this paper a new methodology to detect and localize a possible damage occurred on a framed structure after an earthquake is presented and discussed. The main outcomes retrieved from many numerical non linear dynamic models of reinforced concrete framed structures characterized by 3, 5 and 8 floors with different geometric configurations and designed for gravity loads only are here presented. In addition, the main results of experimental shaking table tests carried out on a steel framed model are also showed to confirm the effectiveness of the proposed procedure. Acknowledgements This study was partially funded by the Italian Civil Protection Department within the project DPC-RELUIS 2014 - RS4 ''Seismic observatory of structures and health monitoring''.

An information processing view of framing effects: the role of causal schemas in decision making.

PubMed

Jou, J; Shanteau, J; Harris, R J

1996-01-01

People prefer a sure gain to a probable larger gain when the two choices are presented from a gain perspective, but a probable larger loss to a sure loss when the objectively identical choices are presented from a loss perspective. Such reversals of preference due to the context of the problem are known as framing effects. In the present study, schema activation and subjects' interpretations of the problems were examined as sources of the framing effects. Results showed that such effects could be eliminated by introducing into a problem a causal schema that provided a rationale for the reciprocal relationship between the gains and the losses. Moreover, when subjects were freed from framing they were consistently risk seeking in decisions about human life, but risk averse in decisions about property. Irrationality in choice behaviors and the ecological implication of framing effects are discussed.

1.56 Terahertz 2-frames per second standoff imaging

NASA Astrophysics Data System (ADS)

Goyette, Thomas M.; Dickinson, Jason C.; Linden, Kurt J.; Neal, William R.; Joseph, Cecil S.; Gorveatt, William J.; Waldman, Jerry; Giles, Robert; Nixon, William E.

2008-02-01

A Terahertz imaging system intended to demonstrate identification of objects concealed under clothing was designed, assembled, and tested. The system design was based on a 2.5 m standoff distance, with a capability of visualizing a 0.5 m by 0.5 m scene at an image rate of 2 frames per second. The system optical design consisted of a 1.56 THz laser beam, which was raster swept by a dual torsion mirror scanner. The beam was focused onto the scan subject by a stationary 50 cm-diameter focusing mirror. A heterodyne detection technique was used to down convert the backscattered signal. The system demonstrated a 1.5 cm spot resolution. Human subjects were scanned at a frame rate of 2 frames per second. Hidden metal objects were detected under a jacket worn by the human subject. A movie including data and video images was produced in 1.5 minutes scanning a human through 180° of azimuth angle at 0.7° increment.

Quantifying the effect of disruptions to temporal coherence on the intelligibility of compressed American Sign Language video

NASA Astrophysics Data System (ADS)

Ciaramello, Frank M.; Hemami, Sheila S.

2009-02-01

Communication of American Sign Language (ASL) over mobile phones would be very beneficial to the Deaf community. ASL video encoded to achieve the rates provided by current cellular networks must be heavily compressed and appropriate assessment techniques are required to analyze the intelligibility of the compressed video. As an extension to a purely spatial measure of intelligibility, this paper quantifies the effect of temporal compression artifacts on sign language intelligibility. These artifacts can be the result of motion-compensation errors that distract the observer or frame rate reductions. They reduce the the perception of smooth motion and disrupt the temporal coherence of the video. Motion-compensation errors that affect temporal coherence are identified by measuring the block-level correlation between co-located macroblocks in adjacent frames. The impact of frame rate reductions was quantified through experimental testing. A subjective study was performed in which fluent ASL participants rated the intelligibility of sequences encoded at a range of 5 different frame rates and with 3 different levels of distortion. The subjective data is used to parameterize an objective intelligibility measure which is highly correlated with subjective ratings at multiple frame rates.

A Bayesian Account of Visual-Vestibular Interactions in the Rod-and-Frame Task.

PubMed

Alberts, Bart B G T; de Brouwer, Anouk J; Selen, Luc P J; Medendorp, W Pieter

2016-01-01

Panoramic visual cues, as generated by the objects in the environment, provide the brain with important information about gravity direction. To derive an optimal, i.e., Bayesian, estimate of gravity direction, the brain must combine panoramic information with gravity information detected by the vestibular system. Here, we examined the individual sensory contributions to this estimate psychometrically. We asked human subjects to judge the orientation (clockwise or counterclockwise relative to gravity) of a briefly flashed luminous rod, presented within an oriented square frame (rod-in-frame). Vestibular contributions were manipulated by tilting the subject's head, whereas visual contributions were manipulated by changing the viewing distance of the rod and frame. Results show a cyclical modulation of the frame-induced bias in perceived verticality across a 90° range of frame orientations. The magnitude of this bias decreased significantly with larger viewing distance, as if visual reliability was reduced. Biases increased significantly when the head was tilted, as if vestibular reliability was reduced. A Bayesian optimal integration model, with distinct vertical and horizontal panoramic weights, a gain factor to allow for visual reliability changes, and ocular counterroll in response to head tilt, provided a good fit to the data. We conclude that subjects flexibly weigh visual panoramic and vestibular information based on their orientation-dependent reliability, resulting in the observed verticality biases and the associated response variabilities.

The Application of Artificial Intelligence to the Management of the Army’s Mobile Subscriber Equipment Communications System

DTIC Science & Technology

1992-06-01

and may be better suited for knowledge representation. Frames Researcher Marvin Minsky developed the concept of Frames to describe how humans organize...knowledge about common concepts and situations.’ Minsky hypothesized that people do not construct new knowledge structures from scratch when they...to store new information. Minsky called these knowledge structures frames. Frames can be viewed as complex semantic nets. Frame diagrams show the

Automating Frame Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanfilippo, Antonio P.; Franklin, Lyndsey; Tratz, Stephen C.

2008-04-01

Frame Analysis has come to play an increasingly stronger role in the study of social movements in Sociology and Political Science. While significant steps have been made in providing a theory of frames and framing, a systematic characterization of the frame concept is still largely lacking and there are no rec-ognized criteria and methods that can be used to identify and marshal frame evi-dence reliably and in a time and cost effective manner. Consequently, current Frame Analysis work is still too reliant on manual annotation and subjective inter-pretation. The goal of this paper is to present an approach to themore » representation, acquisition and analysis of frame evidence which leverages Content Analysis, In-formation Extraction and Semantic Search methods to provide a systematic treat-ment of a Frame Analysis and automate frame annotation.« less

Design, Fabrication and Test of Composite Curved Frames for Helicopter Fuselage Structure

NASA Technical Reports Server (NTRS)

Lowry, D. W.; Krebs, N. E.; Dobyns, A. L.

1984-01-01

Aspects of curved beam effects and their importance in designing composite frame structures are discussed. The curved beam effect induces radial flange loadings which in turn causes flange curling. This curling increases the axial flange stresses and induces transverse bending. These effects are more important in composite structures due to their general inability to redistribute stresses by general yielding, such as in metal structures. A detailed finite element analysis was conducted and used in the design of composite curved frame specimens. Five specimens were statically tested and compared with predicted and test strains. The curved frame effects must be accurately accounted for to avoid premature fracture; finite element methods can accurately predict most of the stresses and no elastic relief from curved beam effects occurred in the composite frames tested. Finite element studies are presented for comparative curved beam effects on composite and metal frames.

Covariance and the hierarchy of frame bundles

NASA Technical Reports Server (NTRS)

Estabrook, Frank B.

1987-01-01

This is an essay on the general concept of covariance, and its connection with the structure of the nested set of higher frame bundles over a differentiable manifold. Examples of covariant geometric objects include not only linear tensor fields, densities and forms, but affinity fields, sectors and sector forms, higher order frame fields, etc., often having nonlinear transformation rules and Lie derivatives. The intrinsic, or invariant, sets of forms that arise on frame bundles satisfy the graded Cartan-Maurer structure equations of an infinite Lie algebra. Reduction of these gives invariant structure equations for Lie pseudogroups, and for G-structures of various orders. Some new results are introduced for prolongation of structure equations, and for treatment of Riemannian geometry with higher-order moving frames. The use of invariant form equations for nonlinear field physics is implicitly advocated.

Development Directions for Various Types of the Light Wood-Framed Structures

NASA Astrophysics Data System (ADS)

Malesza, J.; Baszeń, M.; Miedziałowski, Cz

2017-11-01

The paper presents current trends in the development of the wood-framed structures. Authors describe the evolution of the technology of implementation, the production process of precast elements of buildings as well as selected realization on the site of these kinds of structures. The attention has been paid to the effect of implementation phases on construction and erecting technology of the wood-framed structures. The paper draws attention to the importance and enhancement of structural analysis of structures in individual phases of building realization.

Earthquake Response of Reinforced Concrete Building Retrofitted with Geopolymer Concrete and X-shaped Metallic Damper

NASA Astrophysics Data System (ADS)

Madheswaran, C. K.; Prakash vel, J.; Sathishkumar, K.; Rao, G. V. Rama

2017-06-01

A three-storey half scale reinforced concrete (RC) building is fixed with X-shaped metallic damper at the ground floor level, is designed and fabricated to study its seismic response characteristics. Experimental studies are carried out using the (4 m × 4 m) tri-axial shake-table facility to evaluate the seismic response of a retrofitted RC building with open ground storey (OGS) structure using yielding type X-shaped metallic dampers (also called as Added Damping and Stiffness-ADAS elements) and repairing the damaged ground storey columns using geopolymer concrete composites. This elasto-plastic device is normally incorporated within the frame structure between adjacent floors through chevron bracing, so that they efficiently enhance the overall energy dissipation ability of the seismically deficient frame structure under earthquake loading. Free vibration tests on RC building without and with yielding type X-shaped metallic damper is carried out. The natural frequencies and mode shapes of RC building without and with yielding type X-shaped metallic damper are determined. The retrofitted reinforced concrete building is subjected to earthquake excitations and the response from the structure is recorded. This work discusses the preparation of test specimen, experimental set-up, instrumentation, method of testing of RC building and the response of the structure. The metallic damper reduces the time period of the structure and displacement demands on the OGS columns of the structure. Nonlinear time history analysis is performed using structural analysis package, SAP2000.

Evaluation of a pulse control law for flexible spacecraft

NASA Technical Reports Server (NTRS)

1985-01-01

The following analytical and experimental studies were conducted: (1) A simple algorithm was developed to suppress the structural vibrations of 3-dimensional distributed parameter systems, subjected to interface motion and/or directly applied forces. The algorithm is designed to cope with structural oscillations superposed on top of rigid-body motion: a situation identical to that encountered by the SCOLE components. A significant feature of the method is that only local measurements of the structural displacements and velocities relative to the moving frame of reference are needed. (2) A numerical simulation study was conducted on a simple linear finite element model of a cantilevered plate which was subjected to test excitations consisting of impulsive base motion and of nonstationary wide-band random excitation applied at its root. In each situation, the aim was to suppress the vibrations of the plate relative to the moving base. (3) A small mechanical model resembling an aircraft wing was designed and fabricated to investigate the control algorithm under realistic laboratory conditions.

Thermal Behaviour of Beams with Slant End-Plate Connection Subjected to Nonsymmetric Gravity Load

PubMed Central

Osman, Mohd Hanim; Talebi, Elnaz

2014-01-01

Research on the steel structures with confining of axial expansion in fixed beams has been quite intensive in the past decade. It is well established that the thermal behaviour has a key influence on steel structural behaviours. This paper describes mechanical behaviour of beams with bolted slant end-plate connection with nonsymmetric gravity load, subjected to temperature increase. Furthermore, the performance of slant connections of beams in steel moment frame structures in the elastic field is investigated. The proposed model proved that this flexible connection system could successfully decrease the extra thermal induced axial force by both of the friction force dissipation among two faces of slant connection and a small upward movement on the slant plane. The applicability of primary assumption is illustrated. The results from the proposed model are examined within various slant angles, thermal and friction factors. It can be concluded that higher thermal conditions are tolerable when slanting connection is used. PMID:24587720

Thermal behaviour of beams with slant end-plate connection subjected to nonsymmetric gravity load.

PubMed

Zahmatkesh, Farshad; Osman, Mohd Hanim; Talebi, Elnaz

2014-01-01

Research on the steel structures with confining of axial expansion in fixed beams has been quite intensive in the past decade. It is well established that the thermal behaviour has a key influence on steel structural behaviours. This paper describes mechanical behaviour of beams with bolted slant end-plate connection with nonsymmetric gravity load, subjected to temperature increase. Furthermore, the performance of slant connections of beams in steel moment frame structures in the elastic field is investigated. The proposed model proved that this flexible connection system could successfully decrease the extra thermal induced axial force by both of the friction force dissipation among two faces of slant connection and a small upward movement on the slant plane. The applicability of primary assumption is illustrated. The results from the proposed model are examined within various slant angles, thermal and friction factors. It can be concluded that higher thermal conditions are tolerable when slanting connection is used.

The effect of frame rate on the ability of experienced gait analysts to identify characteristics of gait from closed circuit television footage.

PubMed

Birch, Ivan; Vernon, Wesley; Burrow, Gordon; Walker, Jeremy

2014-03-01

Forensic gait analysis is increasingly being used as part of criminal investigations. A major issue is the quality of the closed circuit television (CCTV) footage used, particularly the frame rate which can vary from 25 frames per second to one frame every 4s. To date, no study has investigated the effect of frame rate on forensic gait analysis. A single subject was fitted with an ankle foot orthosis and recorded walking at 25 frames per second. 3D motion data were also collected, providing an absolute assessment of the gait characteristics. The CCTV footage was then edited to produce a set of eight additional pieces of footage, at various frame rates. Practitioners with knowledge of forensic gait analysis were recruited and instructed to record their observations regarding the characteristics of the subject's gait from the footage. They were sequentially sent web links to the nine pieces of footage, lowest frame rate first, and a simple observation recording form, over a period of 8 months. A sample-based Pearson product-moment correlation analysis of the results demonstrated a significant positive relationship between frame rate and scores (r=0.868, p=0.002). The results of this study show that frame rate affects the ability of experienced practitioners to identify characteristics of gait captured on CCTV footage. Every effort should therefore be made to ensure that CCTV footage likely to be used in criminal proceedings is captured at as high a frame rate as possible. © 2013.

Impact localization and energy quantification based on the power flow: A low-power requirement approach

NASA Astrophysics Data System (ADS)

Guyomar, Daniel; Lallart, Mickaël; Petit, Lionel; Wang, Xing-Jun

2011-06-01

The increasing use of composite materials has led to a dramatic change in the definition of safety standards. In particular, composite structures may be subjected to internal damages caused by external impacts that may not be detected by classical inspection methods. Additional constraints related to energy requirements may also be considered in order to make the system autonomous and possibly self-powered. The purpose of this paper is to present a low-cost impact detection and quantification scheme for thin plates or shells giving the whole history of the structure solicitation. Based on the analysis of the energy that has flown over a monitored area through the use of the elastic Poynting vector (that relates the mechanical power density of travelling waves), it is shown that this global energy balance may be linked in a simple way to the voltage output of piezoelectric elements in open-circuit condition. From this estimation, it is therefore possible to detect if an impact occurred inside the monitored area (in this case, the global energy balance would be positive) as well as its associated energy. If the impact occurs out of the frame, the global energy (and thus the obtained estimator) would be negative because of energy dissipation caused by internal losses and almost null. Thanks to this energy flow approach, the system is also independent from the boundary conditions of the structure. Experimental measurements aiming at validating the theoretical predictions showed that the technique permits detecting the impact area (inside/outside the frame) as well as an accurate estimation of the impact energy if the latter occurred inside the frame, both on a steel plate (with different boundary conditions) and an anisotropic composite structure.

Tracking scanning laser ophthalmoscope (TSLO)

NASA Astrophysics Data System (ADS)

Hammer, Daniel X.; Ferguson, R. Daniel; Magill, John C.; White, Michael A.; Elsner, Ann E.; Webb, Robert H.

2003-07-01

The effectiveness of image stabilization with a retinal tracker in a multi-function, compact scanning laser ophthalmoscope (TSLO) was demonstrated in initial human subject tests. The retinal tracking system uses a confocal reflectometer with a closed loop optical servo system to lock onto features in the fundus. The system is modular to allow configuration for many research and clinical applications, including hyperspectral imaging, multifocal electroretinography (MFERG), perimetry, quantification of macular and photo-pigmentation, imaging of neovascularization and other subretinal structures (drusen, hyper-, and hypo-pigmentation), and endogenous fluorescence imaging. Optical hardware features include dual wavelength imaging and detection, integrated monochromator, higher-order motion control, and a stimulus source. The system software consists of a real-time feedback control algorithm and a user interface. Software enhancements include automatic bias correction, asymmetric feature tracking, image averaging, automatic track re-lock, and acquisition and logging of uncompressed images and video files. Normal adult subjects were tested without mydriasis to optimize the tracking instrumentation and to characterize imaging performance. The retinal tracking system achieves a bandwidth of greater than 1 kHz, which permits tracking at rates that greatly exceed the maximum rate of motion of the human eye. The TSLO stabilized images in all test subjects during ordinary saccades up to 500 deg/sec with an inter-frame accuracy better than 0.05 deg. Feature lock was maintained for minutes despite subject eye blinking. Successful frame averaging allowed image acquisition with decreased noise in low-light applications. The retinal tracking system significantly enhances the imaging capabilities of the scanning laser ophthalmoscope.

A-frame model for metaphor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kilpatrick, W.

1982-01-01

While literal language is successfully being subjected to automatic analysis, metaphors remain intractable. Using Minsky's frame theory the metaphoric process is viewed as a copying of stereotypic terminal clusters from the frames of the 1 degrees and 2 degrees terms of the metaphor. Stereotypic values from the two original frames share equal status in this new frame, while non-stereotypic values from the two will be kept separate for possible use in metaphoric extension. The a-frame analysis is illustrated by application to non-literary novel metaphors. Frames provide the quantity of information needed for interpretation. Certain frame values are marked as stereotypic.more » Creativity is realized by the construction of a new a-frame, and the tension is realized by the presence in a single a-frame of both shared stereotypic and discrete non-stereotypic values. 10 references.« less

Structural determinants of an internal ribosome entry site that direct translational reading frame selection

PubMed Central

Ren, Qian; Au, Hilda H.T.; Wang, Qing S.; Lee, Seonghoon; Jan, Eric

2014-01-01

The dicistrovirus intergenic internal ribosome entry site (IGR IRES) directly recruits the ribosome and initiates translation using a non-AUG codon. A subset of IGR IRESs initiates translation in either of two overlapping open reading frames (ORFs), resulting in expression of the 0 frame viral structural polyprotein and an overlapping +1 frame ORFx. A U–G base pair adjacent to the anticodon-like pseudoknot of the IRES directs +1 frame translation. Here, we show that the U-G base pair is not absolutely required for +1 frame translation. Extensive mutagenesis demonstrates that 0 and +1 frame translation can be uncoupled. Ribonucleic acid (RNA) structural probing analyses reveal that the mutant IRESs adopt distinct conformations. Toeprinting analysis suggests that the reading frame is selected at a step downstream of ribosome assembly. We propose a model whereby the IRES adopts conformations to occlude the 0 frame aminoacyl-tRNA thereby allowing delivery of the +1 frame aminoacyl-tRNA to the A site to initiate translation of ORFx. This study provides a new paradigm for programmed recoding mechanisms that increase the coding capacity of a viral genome. PMID:25038250

Framing and visual type: Effect on future Zika vaccine uptake intent.

PubMed

Guidry, Jeanine P D; Carlyle, Kellie E; LaRose, Jessica G; Perrin, Paul; Ryan, Mark; Messner, Marcus; Adams, Jay

2018-02-05

The Zika virus is associated with the birth defect microcephaly, and while a vaccine was not available in early- 2017, several were under development. This study's purpose was to identify effective communication strategies to promote uptake of a new vaccine, particularly among women of reproductive age. In order to study the effects of Zika message framing (gain vs . loss) and visual type (photo vs . infographic) on future Zika vaccine uptake intent, a 2×2 between-subjects experiment was performed via an online survey in 2017 among 339 U.S. women of reproductive age (18-49 years). Participants were exposed to one of four messages, all resembling Instagram posts: gain-framed vs. loss-framed infographic, and gain-framed vs . loss-framed photo. These messages were followed by questions about Zika vaccine uptake intent as well as intermediate psychosocial variables that could lead to intent. There was no interaction between framing and visual type (P=0.116), and there was no effect for framing (P=0.185) or visual type (P=0.724) on future Zika vaccine uptake intent, which is likely indicative of insufficient dosage of the intervention. However, when focusing on intermediate psychosocial constructs that are known to influence behavior and intent, gain-framed messages were more effective in increasing subjective norms (P=0.005) as related to a future Zika vaccine, as well as perceived benefits (P=0.016) and self-efficacy (P=0.032). Gain-framed messages seem to be more effective than loss-framed messages to increase several constructs that could, in turn, affect future Zika vaccine uptake intent. This is a novel finding since, traditionally, loss-framed messages are considered more beneficial in promoting vaccine-related health behaviors.

A novel method of naturally contouring the reconstructed ear: modified antihelix complex affixed to grooved base frame.

PubMed

Li, Datao; Zhang, Ruhong; Zhang, Qun; Xu, Zhicheng; Xu, Feng; Li, Yiyuan; Sun, Nan; Wang, Cheng

2014-05-01

Prior reports of ear reconstruction have cited favorable results. Although greater attention has been devoted to fabricating a more refined cartilaginous framework, many patients still complain that the contours are unnatural. The authors' aim was to offer a new technique that resolves some lingering issues. To fabricate the antihelix complex optimally, the authors modified an existing method. Rather than chiseling a sharp, Y-shaped graft of cartilage for structural prominence, the superior crus is broadened, and a gentle slope is sculpted on both aspects. Simultaneously, a groove in the base frame is carved for smooth attachment. The width of the inferior crus is limited to roughly one-third that of the superior crus, and the inferior crus is maintained in high relief. A gentle slope is shaped on the antihelix, and a groove for placement of the antihelix is carved into the base frame. Between 2011 and 2013, a total of 162 patients underwent reconstruction using this modified technique. Three such subjects have been selected to highlight the favorable results achieved. Given modifications confer natural contours to superior and inferior crura, antihelix, and surrounding structures, providing a cohesive framework for the integrity of a reconstructed ear. The antihelix complex is critical for creating a natural auricle. Harmonious integration of superior and inferior crura and antihelix enhances the overall aesthetics, increasing procedural satisfaction for patient and surgeon alike. Therapeutic, IV.

24 CFR 3280.306 - Windstorm protection.

Code of Federal Regulations, 2011 CFR

2011-04-01

... URBAN DEVELOPMENT MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARDS Body and Frame Construction... frame structure to be used as the points for connection of diagonal ties, no specific connecting devices need be provided on the main frame structure. (b) Contents of instructions. (1) The manufacturer must...

24 CFR 3280.306 - Windstorm protection.

Code of Federal Regulations, 2010 CFR

2010-04-01

... URBAN DEVELOPMENT MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARDS Body and Frame Construction... frame structure to be used as the points for connection of diagonal ties, no specific connecting devices need be provided on the main frame structure. (b) Contents of instructions. (1) The manufacturer must...

In situ damage detection in frame structures through coupled response measurements

NASA Astrophysics Data System (ADS)

Liu, D.; Gurgenci, H.; Veidt, M.

2004-05-01

Due to the existence of global modes and local modes of the neighbouring members, damage detection on a structure is more challenging than damage on isolated beams. Detection of an artificial circumferential crack on a joint in a frame-like welded structure is studied in this paper using coupled response measurements. Similarity to real engineering structures is maintained in the fabrication of the test frame. Both the chords and the branch members have hollow sections and the branch members have smaller sizes. The crack is created by a hacksaw on a joint where a branch meets the chord. The methodology is first demonstrated on a single hollow section beam. The test results are then presented for the damaged and undamaged frame. The existence of the damage is clearly observable from the experimental results. It is suggested that this approach offers the potential to detect damage in welded structures such as cranes, mining equipment, steel-frame bridges, naval and offshore structures.

Multi-frame image processing with panning cameras and moving subjects

NASA Astrophysics Data System (ADS)

Paolini, Aaron; Humphrey, John; Curt, Petersen; Kelmelis, Eric

2014-06-01

Imaging scenarios commonly involve erratic, unpredictable camera behavior or subjects that are prone to movement, complicating multi-frame image processing techniques. To address these issues, we developed three techniques that can be applied to multi-frame image processing algorithms in order to mitigate the adverse effects observed when cameras are panning or subjects within the scene are moving. We provide a detailed overview of the techniques and discuss the applicability of each to various movement types. In addition to this, we evaluated algorithm efficacy with demonstrated benefits using field test video, which has been processed using our commercially available surveillance product. Our results show that algorithm efficacy is significantly improved in common scenarios, expanding our software's operational scope. Our methods introduce little computational burden, enabling their use in real-time and low-power solutions, and are appropriate for long observation periods. Our test cases focus on imaging through turbulence, a common use case for multi-frame techniques. We present results of a field study designed to test the efficacy of these techniques under expanded use cases.

An experimental investigation on the ultimate strength of epoxy repaired braced partial infilled RC frames

NASA Astrophysics Data System (ADS)

Dubey, Shailendra Kumar Damodar; Kute, Sunil

2014-09-01

Due to earthquake, buildings are damaged partially or completely. Particularly structures with soft storey are mostly affected. In general, such damaged structures are repaired and reused. In this regard, an experimental investigation was planned and conducted on models of single-bay, single-storey of partial concrete infilled reinforced concrete (RC) frames up to collapse with corner, central and diagonal steel bracings. Such collapsed frames were repaired with epoxy resin and retested. The initiative was to identify the behaviour, extent of restored ultimate strength and deflection of epoxy-retrofitted frames in comparison to the braced RC frames. The performance of such frames has been considered only for lateral loads. In comparison to bare RC frames, epoxy repaired partial infilled frames have significant increase in the lateral load capacity. Central bracing is more effective than corner and diagonal bracing. For the same load, epoxy repaired frames have comparable deflection than similar braced frames.

Research on the Best Root Span of 500kV Substation Frame Based on Finite Element

NASA Astrophysics Data System (ADS)

Chen, Hao; Fang, Qing; Chen, Haoyuan

2018-01-01

A-shaped and steel tube structures have been widely applied when designing 500kV substation frame in China. While, compared with steel tube, angle steels have an advantage of easy-transporting, especially in oversea projects. However, researches on substation frame with angle steel were not enough. In order to find out the best root span of 500kV substation frame under similar engineering conditions, using the overseas project substation frame as an example, the substation frames with different root span have been detailed calculated, to find the best root span according to the cost of it. When the height of column is about 30m, the root suggestion value is 6.1m×3.1m. And then, the buckling analysis of the overall structure has been carried out by ANSYS, to find out that the weak part of the structure is in the middle of it. The structural adjustment is carried out for the weak part, including adjusting the web members and the chord members, to obtain a higher bearing capacity of the structure.

How Framing Statistical Statements Affects Subjective Veracity: Validation and Application of a Multinomial Model for Judgments of Truth

ERIC Educational Resources Information Center

Hilbig, Benjamin E.

2012-01-01

Extending the well-established negativity bias in human cognition to truth judgments, it was recently shown that negatively framed statistical statements are more likely to be considered true than formally equivalent statements framed positively. However, the underlying processes responsible for this effect are insufficiently understood.…

Joint Service Aircrew Mask (JSAM) Extended Wear Comfort Evaluation

DTIC Science & Technology

2009-10-01

JSAM eyeglass frames containing his optical prescription. Comfort Questionnaire (CQ). The CQ was completed ten times as scheduled by the USAF...and comfort of the JSAM while wearing eyeglass frames was very acceptable. Their ability to see was reported as acceptable. No fogging of the...Performance Wing acceleration and altitude test subject panels. The subjects were male, ranged in age from 28-39 years, physically fit , and considered

Finding models to detect Alzheimer's disease by fusing structural and neuropsychological information

NASA Astrophysics Data System (ADS)

Giraldo, Diana L.; García-Arteaga, Juan D.; Velasco, Nelson; Romero, Eduardo

2015-12-01

Alzheimer's disease (AD) is a neurodegenerative disease that affects higher brain functions. Initial diagnosis of AD is based on the patient's clinical history and a battery of neuropsychological tests. The accuracy of the diagnosis is highly dependent on the examiner's skills and on the evolution of a variable clinical frame. This work presents an automatic strategy that learns probabilistic brain models for different stages of the disease, reducing the complexity, parameter adjustment and computational costs. The proposed method starts by setting a probabilistic class description using the information stored in the neuropsychological test, followed by constructing the different structural class models using membership values from the learned probabilistic functions. These models are then used as a reference frame for the classification problem: a new case is assigned to a particular class simply by projecting to the different models. The validation was performed using a leave-one-out cross-validation, two classes were used: Normal Control (NC) subjects and patients diagnosed with mild AD. In this experiment it is possible to achieve a sensibility and specificity of 80% and 79% respectively.

Multicriteria Analysis of Assembling Buildings from Steel Frame Structures

NASA Astrophysics Data System (ADS)

Miniotaite, Ruta

2017-10-01

Steel frame structures are often used in the construction of public and industrial buildings. They are used for: all types of slope roofs; walls of newly-built public and industrial buildings; load bearing structures; roofs of renovated buildings. The process of assembling buildings from steel frame structures should be analysed as an integrated process influenced by such factors as construction materials and machinery used, the qualification level of construction workers, complexity of work, available finance. It is necessary to find a rational technological design solution for assembling buildings from steel frame structures by conducting a multiple criteria analysis. The analysis provides a possibility to evaluate the engineering considerations and find unequivocal solutions. The rational alternative of a complex process of assembling buildings from steel frame structures was found through multiple criteria analysis and multiple criteria evaluation. In multiple criteria evaluation of technological solutions for assembling buildings from steel frame structures by pairwise comparison method the criteria by significance are distributed as follows: durability is the most important criterion in the evaluation of alternatives; the price (EUR/unit of measurement) of a part of assembly process; construction workers’ qualification level (category); mechanization level of a part of assembling process (%), and complexity of assembling work (in points) are less important criteria.

Decisional strategy determines whether frame influences treatment preferences for medical decisions.

PubMed

Woodhead, Erin L; Lynch, Elizabeth B; Edelstein, Barry A

2011-06-01

Decision makers are influenced by the frame of information such that preferences vary depending on whether survival or mortality data are presented. Research is inconsistent as to whether and how age impacts framing effects. This paper presents two studies that used qualitative analyses of think-aloud protocols to understand how the type of information used in the decision making process varies by frame and age. In Study 1, 40 older adults, age 65 to 89, and 40 younger adults, age 18 to 24, responded to a hypothetical lung cancer scenario in a within-subject design. Participants received both a survival and mortality frame. Qualitative analyses revealed that two main decisional strategies were used by all participants: one strategy reflected a data-driven decisional process, whereas the other reflected an experience-driven process. Age predicted decisional strategy, with older adults less likely to use a data-driven strategy. Frame interacted with strategy to predict treatment choice; only those using a data-driven strategy demonstrated framing effects. In Study 2, 61 older adults, age 65 to 98, and 63 younger adults, age 18 to 30, responded to the same scenarios as in Study 1 in a between-subject design. The results of Study 1 were replicated, with age significantly predicting decisional strategy and frame interacting with strategy to predict treatment choice. Findings suggest that framing effects may be more related to decisional strategy than to age. (c) 2011 APA, all rights reserved.

Evidence for a neural correlate of a framing effect: bias-specific activity in the ventromedial prefrontal cortex during credibility judgments.

PubMed

Deppe, M; Schwindt, W; Krämer, J; Kugel, H; Plassmann, H; Kenning, P; Ringelstein, E B

2005-11-15

Neural processes within the medial prefrontal cortex play a crucial role in assessing and integrating emotional and other implicit information during decision-making. Phylogenetically, it was important for the individual to assess the relevance of all kinds of environmental stimuli in order to adapt behavior in a flexible manner. Consequently, we can in principle not exclude that environmental information covertly influences the evaluation of actually decision relevant facts ("framing effect"). To test the hypothesis that the medial prefrontal cortex is involved into a framing effect we employed functional magnetic resonance imaging (fMRI) during a binary credibility judgment task. Twenty-one subjects were asked to judge 30 normalized news magazine headlines by forced answers as "true" or "false". To confound the judgments by formally irrelevant framing information we presented each of the headlines in four different news magazines characterized by varying credibility. For each subject the susceptibility to the judgment confounder (framing information) was assessed by magazine-specific modifications of the answers given. We could show that individual activity changes of the ventromedial prefrontal cortex during the judgments correlate with the degree of an individual's susceptibility to the framing information. We found (i) a neural correlate of a framing effect as postulated by behavioral decision theorists that (ii) reflects interindividual differences in the degree of the susceptibility to framing information.

Experiment study on RC frame retrofitted by the external structure

NASA Astrophysics Data System (ADS)

Liu, Chunyang; Shi, Junji; Hiroshi, Kuramoto; Taguchi, Takashi; Kamiya, Takashi

2016-09-01

A new retrofitting method is proposed herein for reinforced concrete (RC) structures through attachment of an external structure. The external structure consists of a fiber concrete encased steel frame, connection slab and transverse beams. The external structure is connected to the existing structure through a connection slab and transverse beams. Pseudostatic experiments were carried out on one unretrofitted specimen and three retrofitted frame specimens. The characteristics, including failure mode, crack pattern, hysteresis loops behavior, relationship of strain and displacement of the concrete slab, are demonstrated. The results show that the load carrying capacity is obviously increased, and the extension length of the slab and the number of columns within the external frame are important influence factors on the working performance of the existing structure. In addition, the displacement difference between the existing structure and the outer structure was caused mainly by three factors: shear deformation of the slab, extraction of transverse beams, and drift of the conjunction part between the slab and the existing frame. Furthermore, the total deformation determined by the first two factors accounted for approximately 80% of the damage, therefore these factors should be carefully considered in engineering practice to enhance the effects of this new retrofitting method.

Message Framing and Physical Activity Promotion in Colorectal Cancer Survivors.

PubMed

Hirschey, Rachel; Lipkus, Isaac; Jones, Lee; Mantyh, Christopher; Sloane, Richard; Demark-Wahnefried, Wendy

2016-11-01

To test effects of gain-framed versus loss-framed mailed brochures on increasing physical activity (PA) among colorectal cancer (CRC) survivors.
. Randomized trial with repeated measures at baseline, 1 month, and 12 months postintervention.
. Mail recruitment from tumor registries.
. 148 inactive CRC survivors who had completed primary therapy. 
. PA and constructs from the Theory of Planned Behavior (TPB) were assessed at baseline, 1 month, and 12 months. Participants were randomized to receive pamphlets describing PA benefits (gain framed) or disadvantages of not being physically active (loss framed). Baseline characteristics were compared using descriptive statistics. Repeated measures linear models were used to test PA changes.
. Minutes of PA and TPB constructs.
. Significant PA increases were observed in both study arms. Results did not differ by message frame. At one month, about 25% of previously inactive participants increased activity to national recommendations. Those who increased PA compared to those who did not had higher baseline scores on subjective norms, perceived behavioral control, and PA intentions. 
. Independent of message framing, mailed brochures are highly effective in producing within-subject short- and long-term increases in PA.
. CRC survivors may increase short- and long-term levels of PA by receiving inexpensive print brochures.

Research of spectacle frame measurement system based on structured light method

NASA Astrophysics Data System (ADS)

Guan, Dong; Chen, Xiaodong; Zhang, Xiuda; Yan, Huimin

2016-10-01

Automatic eyeglass lens edging system is now widely used to automatically cut and polish the uncut lens based on the spectacle frame shape data which is obtained from the spectacle frame measuring machine installed on the system. The conventional approach to acquire the frame shape data works in the contact scanning mode with a probe tracing around the groove contour of the spectacle frame which requires a sophisticated mechanical and numerical control system. In this paper, a novel non-contact optical measuring method based on structured light to measure the three dimensional (3D) data of the spectacle frame is proposed. First we focus on the processing approach solving the problem of deterioration of the structured light stripes caused by intense specular reflection on the frame surface. The techniques of bright-dark bi-level fringe projecting, multiple exposuring and high dynamic range imaging are introduced to obtain a high-quality image of structured light stripes. Then, the Gamma transform and median filtering are applied to enhance image contrast. In order to get rid of background noise from the image and extract the region of interest (ROI), an auxiliary lighting system of special design is utilized to help effectively distinguish between the object and the background. In addition, a morphological method with specific morphological structure-elements is adopted to remove noise between stripes and boundary of the spectacle frame. By further fringe center extraction and depth information acquisition through the method of look-up table, the 3D shape of the spectacle frame is recovered.

Leadership capabilities of physiotherapy leaders in Ireland: Part 1 physiotherapy managers.

PubMed

McGowan, Emer; Elliott, Naomi; Stokes, Emma

2018-05-07

Investigation of the leadership capabilities of physiotherapists is needed to allow understanding of current leadership practice and to enable appropriate training programs to be developed. To explore physiotherapy managers´ perceptions of their leadership capabilities. Semi-structured interviews were conducted with a purposive sample of 18 physiotherapy managers from a range of public services and private practices in Ireland. The interviews were analyzed using template analysis and the coding template was based on the Bolman and Deal Leadership framework which details four leadership frames: structural, human resource, political, and symbolic. The physiotherapy managers described demonstrating leadership capabilities associated with each of the four leadership frames. However, the language used by the physiotherapy managers suggested that they work predominantly through the structural and human resource frames. The employment of capabilities associated with the political frame varied between participants; some participants described working through this frame while others reported difficulties. The symbolic frame was underused; there were fewer examples given of capabilities such as communicating their vision, demonstrating passion and facilitating a positive workplace culture. Physiotherapy managers work predominantly through the structural and human resource frames. To successfully meet the leadership requirements of their roles physiotherapy managers may benefit from specific leadership development training to develop leadership capabilities in the political and symbolic frames.

Design, fabrication, and test of lightweight shell structure, phase 2

NASA Technical Reports Server (NTRS)

1974-01-01

A cylindrical shell skirt structure 4.57 m (180 in.) in diameter and 3.66 m (144 in.) high was subjected to a design and analysis study using a wide variety of structural materials and concepts. The design loading of 1225.8 N/cm (700 lb/in.) axial compression and 245.2 N/cm (140 lb/in.) torsion is representative of that expected on a typical space tug skirt section. Structural concepts evaluated included honeycomb sandwich, truss, isogrid, and skin/stringer/frame. The materials considered included a wide variety of structural metals as well as glass, graphite, and boron-reinforced composites. The most unique characteristic of the candidate designs is that they involve the use of very thin-gage material. Fabrication and structural test of small panels and components representative of many of the candidate designs served to demonstrate proposed fabrication techniques and to verify design and analysis methods.

Compression Strength of Composite Primary Structural Components

NASA Technical Reports Server (NTRS)

Johnson, Eric R.

1998-01-01

Research conducted under NASA Grant NAG-1-537 focussed on the response and failure of advanced composite material structures for application to aircraft. Both experimental and analytical methods were utilized to study the fundamental mechanics of the response and failure of selected structural components subjected to quasi-static loads. Most of the structural components studied were thin-walled elements subject to compression, such that they exhibited buckling and postbuckling responses prior to catastrophic failure. Consequently, the analyses were geometrically nonlinear. Structural components studied were dropped-ply laminated plates, stiffener crippling, pressure pillowing of orthogonally stiffened cylindrical shells, axisymmetric response of pressure domes, and the static crush of semi-circular frames. Failure of these components motivated analytical studies on an interlaminar stress postprocessor for plate and shell finite element computer codes, and global/local modeling strategies in finite element modeling. These activities are summarized in the following section. References to literature published under the grant are listed on pages 5 to 10 by a letter followed by a number under the categories of journal publications, conference publications, presentations, and reports. These references are indicated in the text by their letter and number as a superscript.

Facial measurements for frame design.

PubMed

Tang, C Y; Tang, N; Stewart, M C

1998-04-01

Anthropometric data for the purpose of spectacle frame design are scarce in the literature. Definitions of facial features to be measured with existing systems of facial measurement are often not specific enough for frame design and manufacturing. Currently, for individual frame design, experienced personnel collect data with facial rules or instruments. A new measuring system is proposed, making use of a template in the form of a spectacle frame. Upon fitting the template onto a subject, most of the measuring references can be defined. Such a system can be administered by lesser-trained personnel and can be used for researches covering a larger population.

Computer Aided Synthesis or Measurement Schemes for Telemetry applications

DTIC Science & Technology

1997-09-02

5.2.5. Frame structure generation The algorithm generating the frame structure should take as inputs the sampling frequency requirements of the channels...these channels into the frame structure. Generally there can be a lot of ways to divide channels among groups. The algorithm implemented in...groups) first. The algorithm uses the function "try_permutation" recursively to distribute channels among the groups, and the function "try_subtable

Headline violence and silenced pleasure: contested framings of consensual sex, power and rape in Delhi, India 2011-2014.

PubMed

Edmunds, Emme; Gupta, Ankit

2016-05-01

Though coercion and rape have cast a persistent shadow over prospects of sexual health and consent in contemporary India, other narratives, agency and tools are quietly emerging to transform collective claims of power and bodily dignity. In these narratives from collectives, NGOs, on social media and among friends, dialogues about consent and pleasure feature prominently. This paper analyses statements in the news made by highly visible political and public figures regarding the subject of rape in the context of themes emerging from ethnography and semi-structured interviews with middle class people in Delhi. Using the device of social frameworks, contested framings of rape and consent are examined in order to interrogate essentialist gender norms, compare putative "causes" of rape, and highlight local efforts promoting sexual consent, health and well-being. Copyright © 2016 Elsevier Inc. All rights reserved.

Messages that matter: Age differences in affective responses to framed health messages.

PubMed

Mikels, Joseph A; Shuster, Michael M; Thai, Sydney T; Smith-Ray, Renae; Waugh, Christian E; Roth, Kayla; Keilly, Alexis; Stine-Morrow, Elizabeth A L

2016-06-01

Age differences in responses to framed health messages-which can influence judgments and decisions-are critical to understand yet relatively unexplored. Age-related emotional shifts toward positivity would be expected to differentially impact the affective responses of older and younger adults to framed messages. In this study, we measured the subjective and physiological affective responses of older and younger adults to gain- and loss-framed exercise promotion messages. Relative to older adults, younger adults exhibited greater negative reactivity to loss-framed health messages. These results suggest that health message framing does matter, but it depends on the age of the message recipient. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Utilizing Audiovisual and Gain-Framed Messages to Attenuate Psychological Reactance Toward Weight Management Health Messages.

PubMed

Lee, Hyunmin; Cameron, Glen T

2017-01-01

Guided by the psychological reactance theory, this study predicted that gain-framed messages and audiovisual content could counteract state reactance and increase the persuasiveness of weight management health messages. Data from a 2 (message frame: gain/loss) × 2 (modality: audiovisual/text) × 2 (message repetition) within-subjects experiment (N = 82) indicated that in the context of weight management messages for college students, gain-framed messages indeed mitigate psychological reactance. Furthermore, the modality and the frame of the health message interacted in such a way that gain-framed messages in an audiovisual modality generated the highest motivations to comply with the recommendations in the persuasive health messages.

Development of ultrasound/endoscopy PACS (picture archiving and communication system) and investigation of compression method for cine images

NASA Astrophysics Data System (ADS)

Osada, Masakazu; Tsukui, Hideki

2002-09-01

ABSTRACT Picture Archiving and Communication System (PACS) is a system which connects imaging modalities, image archives, and image workstations to reduce film handling cost and improve hospital workflow. Handling diagnostic ultrasound and endoscopy images is challenging, because it produces large amount of data such as motion (cine) images of 30 frames per second, 640 x 480 in resolution, with 24-bit color. Also, it requires enough image quality for clinical review. We have developed PACS which is able to manage ultrasound and endoscopy cine images with above resolution and frame rate, and investigate suitable compression method and compression rate for clinical image review. Results show that clinicians require capability for frame-by-frame forward and backward review of cine images because they carefully look through motion images to find certain color patterns which may appear in one frame. In order to satisfy this quality, we have chosen motion JPEG, installed and confirmed that we could capture this specific pattern. As for acceptable image compression rate, we have performed subjective evaluation. No subjects could tell the difference between original non-compressed images and 1:10 lossy compressed JPEG images. One subject could tell the difference between original and 1:20 lossy compressed JPEG images although it is acceptable. Thus, ratios of 1:10 to 1:20 are acceptable to reduce data amount and cost while maintaining quality for clinical review.

Differential Effects of Message Framing on Obesity Policy Support Between Democrats and Republicans.

PubMed

Lee, Tae Kyoung; Kim, Hye Kyung

2017-12-01

This study tests whether gain- and loss-framed messages about establishing obesity-reducing policies have different persuasive effects on Republicans and Democrats. In a randomized between-subject experiment, participants (N = 384) read a message emphasizing either benefits to a society by establishing policies aimed to reduce obesity (i.e., gain-framed message) or costs to a society that fails to establish those policies (i.e., loss-framed message). Results indicated that Democrats perceived the gain-framed message as more persuasive than the loss-framed message and the perceived argument strength fully mediated the framing effect on Democrats' policy support; however, there was no framing effect on perceived argument strength among Republicans. On the other hand, the gain-framed message led Republicans to attribute the cause of obesity less to the individual level compared to the loss-framed message and the no-message condition. We observed no framing difference among Democrats on causal attributions. Theoretical and practical implications of these findings are discussed.

A curricular frame for physics education: Development, comparison with students' interests, and impact on students' achievement and self-concept

NASA Astrophysics Data System (ADS)

Häussler, Peter; Hoffmann, Lore

2000-11-01

This article presents three interlinked studies aimed at: (1) developing a curricular frame for physics education; (2) assessing the students' interest in the contents, contexts, and activities that are suggested by that curricular frame; and (3) developing a curriculum that is in line with that frame and measuring its cognitive and emotional effects on students. The curricular frame was developed by adopting the Delphi technique and drawing on the expertise of 73 persons selected according to specified selection criteria. Interest data of some 8000 students and information of the presently taught physics curriculum were sampled longitudinally as well as cross-sectionally in various German Länder (states) by questionnaire. The third study comprised 23 experimental and 7 control classes. As a result of the comparison between the features of the curricular frame, the interest structure of students, and the current physics curriculum, there is a remarkable congruency between students' interest in physics and the kind of physics education identified in the Delphi study as being relevant. However, there is a considerable discrepancy between students' interest and the kind of physics instruction practiced in the physics classroom. Regression analysis revealed that students' interest in physics as a school subject is hardly related to their interest in physics, but mainly to the students' self-esteem of being good achievers. The data strongly suggest physics be taught so that students have a chance to develop a positive physics-related self-concept and to link physics with situations they encounter outside the classroom. A curriculum based on these principles proved superior compared to a traditional curriculum.

Instrument for controlling the application of mechanical loads to biological and bicompatible test subjects

DOEpatents

Lintilhac, Phillip M.; Vesecky, Thompson B.

1995-01-01

Apparatus and methods are disclosed facilitating the application of forces and measurement of dimensions of a test subject. In one arrangement the test subject is coupled to a forcing frame and controlled forces applied thereto. Force applied to the test subject is measured and controlled. A dimensional characteristic of the test subject, such as growth, is measured by a linear variable differential transformer. The growth measurement data can be used to control the force applied. The transducer module receives force and dimensional data from the forcing frame. The transducer module is a separate, microprocessor-based unit that communicates the test data to a controller unit that controls the application of force to the test subject and receives the test data from the transducer module for force control, storage, and/or communication to the user.

Instrument for controlling the application of mechanical loads to biological and bicompatible test subjects

DOEpatents

Lintilhac, P.M.; Vesecky, T.B.

1995-09-19

An apparatus and methods are disclosed facilitating the application of forces and measurement of dimensions of a test subject. In one arrangement the test subject is coupled to a forcing frame and controlled forces applied thereto. Force applied to the test subject is measured and controlled. A dimensional characteristic of the test subject, such as growth, is measured by a linear variable differential transformer. The growth measurement data can be used to control the force applied. The transducer module receives force and dimensional data from the forcing frame. The transducer module is a separate, microprocessor-based unit that communicates the test data to a controller unit that controls the application of force to the test subject and receives the test data from the transducer module for force control, storage, and/or communication to the user. 8 figs.

Acoustic emission energy b-value for local damage evaluation in reinforced concrete structures subjected to seismic loadings

NASA Astrophysics Data System (ADS)

Sagasta, Francisco; Zitto, Miguel E.; Piotrkowski, Rosa; Benavent-Climent, Amadeo; Suarez, Elisabet; Gallego, Antolino

2018-03-01

A modification of the original b-value (Gutenberg-Richter parameter) is proposed to evaluate local damage of reinforced concrete structures subjected to dynamical loads via the acoustic emission (AE) method. The modification, shortly called energy b-value, is based on the use of the true energy of the AE signals instead of its peak amplitude, traditionally used for the calculation of b-value. The proposal is physically supported by the strong correlation between the plastic strain energy dissipated by the specimen and the true energy of the AE signals released during its deformation and cracking process, previously demonstrated by the authors in several publications. AE data analysis consisted in the use of guard sensors and the Continuous Wavelet Transform in order to separate primary and secondary emissions as much as possible according to particular frequency bands. The approach has been experimentally applied to the AE signals coming from a scaled reinforced concrete frame structure, which was subjected to sequential seismic loads of incremental acceleration peak by means of a 3 × 3 m2 shaking table. For this specimen two beam-column connections-one exterior and one interior-were instrumented with wide band low frequency sensors properly attached on the structure. Evolution of the energy b-value along the loading process accompanies the evolution of the severe damage at the critical regions of the structure (beam-column connections), thus making promising its use for structural health monitoring purposes.

Dynamic frame resizing with convolutional neural network for efficient video compression

NASA Astrophysics Data System (ADS)

Kim, Jaehwan; Park, Youngo; Choi, Kwang Pyo; Lee, JongSeok; Jeon, Sunyoung; Park, JeongHoon

2017-09-01

In the past, video codecs such as vc-1 and H.263 used a technique to encode reduced-resolution video and restore original resolution from the decoder for improvement of coding efficiency. The techniques of vc-1 and H.263 Annex Q are called dynamic frame resizing and reduced-resolution update mode, respectively. However, these techniques have not been widely used due to limited performance improvements that operate well only under specific conditions. In this paper, video frame resizing (reduced/restore) technique based on machine learning is proposed for improvement of coding efficiency. The proposed method features video of low resolution made by convolutional neural network (CNN) in encoder and reconstruction of original resolution using CNN in decoder. The proposed method shows improved subjective performance over all the high resolution videos which are dominantly consumed recently. In order to assess subjective quality of the proposed method, Video Multi-method Assessment Fusion (VMAF) which showed high reliability among many subjective measurement tools was used as subjective metric. Moreover, to assess general performance, diverse bitrates are tested. Experimental results showed that BD-rate based on VMAF was improved by about 51% compare to conventional HEVC. Especially, VMAF values were significantly improved in low bitrate. Also, when the method is subjectively tested, it had better subjective visual quality in similar bit rate.

Structured perceptual input imposes an egocentric frame of reference-pointing, imagery, and spatial self-consciousness.

PubMed

Marcel, Anthony; Dobel, Christian

2005-01-01

Perceptual input imposes and maintains an egocentric frame of reference, which enables orientation. When blindfolded, people tended to mistake the assumed intrinsic axes of symmetry of their immediate environment (a room) for their own egocentric relation to features of the room. When asked to point to the door and window, known to be at mid-points of facing (or adjacent) walls, they pointed with their arms at 180 degrees (or 90 degrees) angles, irrespective of where they thought they were in the room. People did the same when requested to imagine the situation. They justified their responses (inappropriately) by logical necessity or a structural description of the room rather than (appropriately) by relative location of themselves and the reference points. In eight experiments, we explored the effect on this in perception and imagery of: perceptual input (without perceptibility of the target reference points); imaging oneself versus another person; aids to explicit spatial self-consciousness; order of questions about self-location; and the relation of targets to the axes of symmetry of the room. The results indicate that, if one is deprived of structured perceptual input, as well as losing one's bearings, (a) one is likely to lose one's egocentric frame of reference itself, and (b) instead of pointing to reference points, one demonstrates their structural relation by adopting the intrinsic axes of the environment as one's own. This is prevented by providing noninformative perceptual input or by inducing subjects to imagine themselves from the outside, which makes explicit the fact of their being located relative to the world. The role of perceptual contact with a structured world is discussed in relation to sensory deprivation and imagery, appeal is made to Gibson's theory of joint egoreception and exteroception, and the data are related to recent theories of spatial memory and navigation.

From Game Protection to Wildlife Management: Frame Shifts, Organizational Development, and Field Practices

ERIC Educational Resources Information Center

Brulle, Robert J.; Benford, Robert D.

2012-01-01

One enduring question in social movements research is the relationship between cultural representations and organizational structure. In this article, we examine the development of different discursive frames over time, and how such frame shifts affect movement structure and practices. This approach seeks to illuminate the dialectical interplay…

Evaluation of pulmonary function using breathing chest radiography with a dynamic flat panel detector: primary results in pulmonary diseases.

PubMed

Tanaka, Rie; Sanada, Shigeru; Okazaki, Nobuo; Kobayashi, Takeshi; Fujimura, Masaki; Yasui, Masahide; Matsui, Takeshi; Nakayama, Kazuya; Nanbu, Yuko; Matsui, Osamu

2006-10-01

Dynamic flat panel detectors (FPD) permit acquisition of distortion-free radiographs with a large field of view and high image quality. The present study was performed to evaluate pulmonary function using breathing chest radiography with a dynamic FPD. We report primary results of a clinical study and computer algorithm for quantifying and visualizing relative local pulmonary airflow. Dynamic chest radiographs of 18 subjects (1 emphysema, 2 asthma, 4 interstitial pneumonia, 1 pulmonary nodule, and 10 normal controls) were obtained during respiration using an FPD system. We measured respiratory changes in distance from the lung apex to the diaphragm (DLD) and pixel values in each lung area. Subsequently, the interframe differences (D-frame) and difference values between maximum inspiratory and expiratory phases (D-max) were calculated. D-max in each lung represents relative vital capacity (VC) and regional D-frames represent pulmonary airflow in each local area. D-frames were superimposed on dynamic chest radiographs in the form of color display (fusion images). The results obtained using our methods were compared with findings on computed tomography (CT) images and pulmonary functional test (PFT), which were examined before inclusion in the study. In normal subjects, the D-frames were distributed symmetrically in both lungs throughout all respiratory phases. However, subjects with pulmonary diseases showed D-frame distribution patterns that differed from the normal pattern. In subjects with air trapping, there were some areas with D-frames near zero indicated as colorless areas on fusion images. These areas also corresponded to the areas showing air trapping on computed tomography images. In asthma, obstructive abnormality was indicated by areas continuously showing D-frame near zero in the upper lung. Patients with interstitial pneumonia commonly showed fusion images with an uneven color distribution accompanied by increased D-frames in the area identified as normal on computed tomography images. Furthermore, measurement of DLD was very effective for evaluating diaphragmatic kinetics. This is a rapid and simple method for evaluation of respiratory kinetics for pulmonary diseases, which can reveal abnormalities in diaphragmatic kinetics and regional lung ventilation. Furthermore, quantification and visualization of respiratory kinetics is useful as an aid in interpreting dynamic chest radiographs.

Eyeglass Benefits: Consideration of Frame of Choice for Retired Service Members

DTIC Science & Technology

2009-04-20

20100329217 t. ABSTRACT ’he Department of Defense (DoD) provides basic eyewear to our nation’s military members. .Ithough not specifically entitled under...Title X, military retirees historically also receive tandard issue eyewear . The military’s Frame of Choice (FOC) program currently benefits the...current fiscal environment. . SUBJECT TERMS ^eglasses, Frame of Choice, Retiree, Service Members, Entitlements, Eyewear , snefit, Optometry, Optical

Global shape mimicry of tRNA within a viral internal ribosome entry site mediates translational reading frame selection

PubMed Central

Au, Hilda H.; Cornilescu, Gabriel; Mouzakis, Kathryn D.; Ren, Qian; Burke, Jordan E.; Lee, Seonghoon; Butcher, Samuel E.; Jan, Eric

2015-01-01

The dicistrovirus intergenic region internal ribosome entry site (IRES) adopts a triple-pseudoknotted RNA structure and occupies the core ribosomal E, P, and A sites to directly recruit the ribosome and initiate translation at a non-AUG codon. A subset of dicistrovirus IRESs directs translation in the 0 and +1 frames to produce the viral structural proteins and a +1 overlapping open reading frame called ORFx, respectively. Here we show that specific mutations of two unpaired adenosines located at the core of the three-helical junction of the honey bee dicistrovirus Israeli acute paralysis virus (IAPV) IRES PKI domain can uncouple 0 and +1 frame translation, suggesting that the structure adopts distinct conformations that contribute to 0 or +1 frame translation. Using a reconstituted translation system, we show that ribosomes assembled on mutant IRESs that direct exclusive 0 or +1 frame translation lack reading frame fidelity. Finally, a nuclear magnetic resonance/small-angle X-ray scattering hybrid approach reveals that the PKI domain of the IAPV IRES adopts an RNA structure that resembles a complete tRNA. The tRNA shape-mimicry enables the viral IRES to gain access to the ribosome tRNA-binding sites and form intermolecular contacts with the ribosome that are necessary for initiating IRES translation in a specific reading frame. PMID:26554019

INTERIOR; DETAIL OF ROOF FRAMING STRUCTURE, LOOKING SOUTHWEST. Naval ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR; DETAIL OF ROOF FRAMING STRUCTURE, LOOKING SOUTHWEST. - Naval Computer & Telecommunications Area Master Station, Eastern Pacific, Radio Transmitter Facility Lualualei, Helix House No. 2, Base of Radio Antenna Structure No. 427, Makaha, Honolulu County, HI

Building and using a statistical 3D motion atlas for analyzing myocardial contraction in MRI

NASA Astrophysics Data System (ADS)

Rougon, Nicolas F.; Petitjean, Caroline; Preteux, Francoise J.

2004-05-01

We address the issue of modeling and quantifying myocardial contraction from 4D MR sequences, and present an unsupervised approach for building and using a statistical 3D motion atlas for the normal heart. This approach relies on a state-of-the-art variational non rigid registration (NRR) technique using generalized information measures, which allows for robust intra-subject motion estimation and inter-subject anatomical alignment. The atlas is built from a collection of jointly acquired tagged and cine MR exams in short- and long-axis views. Subject-specific non parametric motion estimates are first obtained by incremental NRR of tagged images onto the end-diastolic (ED) frame. Individual motion data are then transformed into the coordinate system of a reference subject using subject-to-reference mappings derived by NRR of cine ED images. Finally, principal component analysis of aligned motion data is performed for each cardiac phase, yielding a mean model and a set of eigenfields encoding kinematic ariability. The latter define an organ-dedicated hierarchical motion basis which enables parametric motion measurement from arbitrary tagged MR exams. To this end, the atlas is transformed into subject coordinates by reference-to-subject NRR of ED cine frames. Atlas-based motion estimation is then achieved by parametric NRR of tagged images onto the ED frame, yielding a compact description of myocardial contraction during diastole.

Optical head tracking for functional magnetic resonance imaging using structured light.

PubMed

Zaremba, Andrei A; MacFarlane, Duncan L; Tseng, Wei-Che; Stark, Andrew J; Briggs, Richard W; Gopinath, Kaundinya S; Cheshkov, Sergey; White, Keith D

2008-07-01

An accurate motion-tracking technique is needed to compensate for subject motion during functional magnetic resonance imaging (fMRI) procedures. Here, a novel approach to motion metrology is discussed. A structured light pattern specifically coded for digital signal processing is positioned onto a fiduciary of the patient. As the patient undergoes spatial transformations in 6 DoF (degrees of freedom), a high-resolution CCD camera captures successive images for analysis on a computing platform. A high-speed image processing algorithm is used to calculate spatial transformations in a time frame commensurate with patient movements (10-100 ms) and with a precision of at least 0.5 microm for translations and 0.1 deg for rotations.

Quiet Clean Short-haul Experimental Engine (QCSEE). Composite fan frame subsystem test report

NASA Technical Reports Server (NTRS)

Stotler, C. L., Jr.; Bowden, J. H.

1977-01-01

The element and subcomponent testing conducted to verify the composite fan frame design of two experimental high bypass geared turbofan engines and propulsion systems for short haul passenger aircraft is described. Emphasis is placed on the propulsion technology required for future externally blown flap aircraft with engines located both under the wing and over the wing, including technology in composite structures and digital engine controls. The element tests confirmed that the processes used in the frame design would produce the predicted mechanical properties. The subcomponent tests verified that the detail structural components of the frame had adequate structural integrity.

On the Performance of a Very Large All-GFRP Strut and Tie Structure

NASA Astrophysics Data System (ADS)

Boscato, G.; Mottram, J. T.; Russo, S.

2014-09-01

An analysis of the dynamic response of a fiber-reinforced-polymer (FRP) structure serving as a temporary (weather) shelter for the church of S. Maria Paganica in L'Aquila is presented. The church suffered roof collapse during a magnitude 6.3 earthquake in April, 2009. The structure is a rectilinear space frame constructed from built-up members of pultruded profiles and steel bolted FRP gusset plates. It has a maximum height of 32 m, covers an area of 1050 m2, and weighs (only) 120 kN. Foundations are free-standing blocks of reinforced concrete connected, just above the floor of the church, by steel bars 16 mm in diameter. A finite-element analysis (FEA) is used to determine the seismic response of the main section to the FRP structure. The nonlinear FE responses of the structure subjected to design response spectra (in the ultimate limit state) are presented and evaluated.

Sensitivity of PZT Impedance Sensors for Damage Detection of Concrete Structures

PubMed Central

Yang, Yaowen; Hu, Yuhang; Lu, Yong

2008-01-01

Piezoelectric ceramic Lead Zirconate Titanate (PZT) based electro-mechanical impedance (EMI) technique for structural health monitoring (SHM) has been successfully applied to various engineering systems. However, fundamental research work on the sensitivity of the PZT impedance sensors for damage detection is still in need. In the traditional EMI method, the PZT electro-mechanical (EM) admittance (inverse of the impedance) is used as damage indicator, which is difficult to specify the effect of damage on structural properties. This paper uses the structural mechanical impedance (SMI) extracted from the PZT EM admittance signature as the damage indicator. A comparison study on the sensitivity of the EM admittance and the structural mechanical impedance to the damages in a concrete structure is conducted. Results show that the SMI is more sensitive to the damage than the EM admittance thus a better indicator for damage detection. Furthermore, this paper proposes a dynamic system consisting of a number of single-degree-of-freedom elements with mass, spring and damper components to model the SMI. A genetic algorithm is employed to search for the optimal value of the unknown parameters in the dynamic system. An experiment is carried out on a two-storey concrete frame subjected to base vibrations that simulate earthquake. A number of PZT sensors are regularly arrayed and bonded to the frame structure to acquire PZT EM admittance signatures. The relationship between the damage index and the distance of the PZT sensor from the damage is studied. Consequently, the sensitivity of the PZT sensors is discussed and their sensing region in concrete is derived. PMID:27879711

Persuading people to eat less junk food: a cognitive resource match between attitudinal ambivalence and health message framing.

PubMed

Yan, Changmin

2015-01-01

This study investigated the interactive effects of attitudinal ambivalence and health message framing on persuading people to eat less junk food. Within the heuristic-systematic model of information processing, an attitudinal ambivalence (ambivalent or univalent toward eating junk food) by health message framing (advantage- or disadvantage-framed appeals) between-subjects experiment was conducted to explore a cognitive resource-matching effect and the underlying mediation processes. Ambivalent individuals reported a higher level of cognitive elaboration than univalent individuals did. The disadvantage frame engendered more extensive cognitive elaboration than the advantage frame did. Ambivalent individuals were more persuaded by the disadvantage frame and, for them, cognitive elaboration mediated the persuasion process via the systematic route. Univalent individuals were equally persuaded by the advantage frame and the disadvantage frame and, for them, neither the perceived frame valence nor cognitive elaboration mediated persuasion. Discussion of the null results among the univalent group leads to a response-reinforcement explanation. Theoretical and practical implications are discussed.

Scope of inextensible frame hypothesis in local action analysis of spherical reservoirs

NASA Astrophysics Data System (ADS)

Vinogradov, Yu. I.

2017-05-01

Spherical reservoirs, as objects perfect with respect to their weight, are used in spacecrafts, where thin-walled elements are joined by frames into multifunction structures. The junctions are local, which results in origination of stress concentration regions and the corresponding rigidity problems. The thin-walled elements are reinforced by frame to decrease the stresses in them. To simplify the analysis of the mathematical model of common deformation of the shell (which is a mathematical idealization of the reservoir) and the frame, the assumption that the frame axial line is inextensible is used widely (in particular, in the manual literature). The unjustified use of this assumption significantly distorts the concept of the stress-strain state. In this paper, an example of a lens-shaped structure formed as two spherical shell segments connected by a frame of square profile is used to carry out a numerical comparative analysis of the solutions with and without the inextensible frame hypothesis taken into account. The scope of the hypothesis is shown depending on the structure geometric parameters and the load location degree. The obtained results can be used to determine the stress-strain state of the thin-walled structure with an a priori prescribed error, for example, in research and experimental design of aerospace systems.

Compressive Testing of Stitched Frame and Stringer Alternate Configurations

NASA Technical Reports Server (NTRS)

Leone, Frank A., Jr.; Jegley, Dawn C.

2016-01-01

A series of single-frame and single-stringer compression tests were conducted at NASA Langley Research Center on specimens harvested from a large panel built using the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. Different frame and stringer designs were used in fabrication of the PRSEUS panel. In this report, the details of the experimental testing of single-frame and single-stringer compression specimens are presented, as well as discussions on the performance of the various structural configurations included in the panel.

Literature Review of Shear Performance of Light-weight Steel Framing Wall Panels

NASA Astrophysics Data System (ADS)

Zhang, Zhuangnan; Liu, Shen; Liu, Hong

2018-03-01

In this paper, a comprehensive review of light-weight steel framing wall panels was carried out. The structure and force characteristics of light-weight steel framing wall panels were introduced. The testing and theoretical research results on the shear behaviour of light-weight steel framing wall panels were summarized in the domestic and foreign. And combined with the existing standards in China, the author's views and ideas are put forward to the problems in the research field of this kind of structural system.

75 FR 4480 - Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-28

... condition as: Reports have been received of finding corrosion at the Frame 29 wing-to-fuselage attachment... structural integrity of Frame 29 and the wing-to-fuselage attachment. * * * * * The unsafe condition is degradation of the structural integrity of Frame 29 and the wing-to-fuselage attachment, which could result in...

Explaining Enhanced Logical Consistency during Decision Making in Autism

PubMed Central

De Martino, Benedetto; Harrison, Neil A.; Knafo, Steven; Bird, Geoff; Dolan, Raymond J.

2009-01-01

The emotional responses elicited by the way options are framed often results in lack of logical consistency in human decision making. In this study, we investigated subjects with autism spectrum disorder (ASD) using a financial task in which the monetary prospects were presented as either loss or gain. We report both behavioral evidence that ASD subjects show a reduced susceptibility to the framing effect and psycho-physiological evidence that they fail to incorporate emotional context into the decision-making process. On this basis, we suggest that this insensitivity to contextual frame, although enhancing choice consistency in ASD, may also underpin core deficits in this disorder. These data highlight both benefits and costs arising from multiple decision processes in human cognition. PMID:18923049

Explaining enhanced logical consistency during decision making in autism.

PubMed

De Martino, Benedetto; Harrison, Neil A; Knafo, Steven; Bird, Geoff; Dolan, Raymond J

2008-10-15

The emotional responses elicited by the way options are framed often results in lack of logical consistency in human decision making. In this study, we investigated subjects with autism spectrum disorder (ASD) using a financial task in which the monetary prospects were presented as either loss or gain. We report both behavioral evidence that ASD subjects show a reduced susceptibility to the framing effect and psycho-physiological evidence that they fail to incorporate emotional context into the decision-making process. On this basis, we suggest that this insensitivity to contextual frame, although enhancing choice consistency in ASD, may also underpin core deficits in this disorder. These data highlight both benefits and costs arising from multiple decision processes in human cognition.

Theoretical research and experimental validation of quasi-static load spectra on bogie frame structures of high-speed trains

NASA Astrophysics Data System (ADS)

Zhu, Ning; Sun, Shou-Guang; Li, Qiang; Zou, Hua

2014-12-01

One of the major problems in structural fatigue life analysis is establishing structural load spectra under actual operating conditions. This study conducts theoretical research and experimental validation of quasi-static load spectra on bogie frame structures of high-speed trains. The quasistatic load series that corresponds to quasi-static deformation modes are identified according to the structural form and bearing conditions of high-speed train bogie frames. Moreover, a force-measuring frame is designed and manufactured based on the quasi-static load series. The load decoupling model of the quasi-static load series is then established via calibration tests. Quasi-static load-time histories, together with online tests and decoupling analysis, are obtained for the intermediate range of the Beijing—Shanghai dedicated passenger line. The damage consistency calibration of the quasi-static discrete load spectra is performed according to a damage consistency criterion and a genetic algorithm. The calibrated damage that corresponds with the quasi-static discrete load spectra satisfies the safety requirements of bogie frames.

Seismic performance for vertical geometric irregularity frame structures

NASA Astrophysics Data System (ADS)

Ismail, R.; Mahmud, N. A.; Ishak, I. S.

2018-04-01

This research highlights the result of vertical geometric irregularity frame structures. The aid of finite element analysis software, LUSAS was used to analyse seismic performance by focusing particularly on type of irregular frame on the differences in height floors and continued in the middle of the building. Malaysia’s building structures were affected once the earthquake took place in the neighbouring country such as Indonesia (Sumatera Island). In Malaysia, concrete is widely used in building construction and limited tension resistance to prevent it. Analysing structural behavior with horizontal and vertical static load is commonly analyses by using the Plane Frame Analysis. The case study of this research is to determine the stress and displacement in the seismic response under this type of irregular frame structures. This study is based on seven-storey building of Clinical Training Centre located in Sungai Buloh, Selayang, Selangor. Since the largest earthquake occurs in Acheh, Indonesia on December 26, 2004, the data was recorded and used in conducting this research. The result of stress and displacement using IMPlus seismic analysis in LUSAS Modeller Software under the seismic response of a formwork frame system states that the building is safe to withstand the ground and in good condition under the variation of seismic performance.

Attribute Framing and Goal Framing Effects in Health Decisions.

PubMed

Krishnamurthy, Parthasarathy; Carter, Patrick; Blair, Edward

2001-07-01

Levin, Schneider, and Gaeth (LSG, 1998) have distinguished among three types of framing-risky choice, attribute, and goal framing-to reconcile conflicting findings in the literature. In the research reported here, we focus on attribute and goal framing. LSG propose that positive frames should be more effective than negative frames in the context of attribute framing, and negative frames should be more effective than positive frames in the context of goal framing. We test this framework by manipulating frame valence (positive vs negative) and frame type (attribute vs goal) in a unified context with common procedures. We also argue that the nature of effects in a goal-framing context may depend on the extent to which the research topic has "intrinsic self-relevance" to the population. In the context of medical decision making, we operationalize low intrinsic self-relevance by using student subjects and high intrinsic self-relevance by using patients. As expected, we find complete support for the LSG framework under low intrinsic self-relevance and modified support for the LSG framework under high intrinsic self-relevance. Overall, our research appears to confirm and extend the LSG framework. Copyright 2001 Academic Press.

Quantitative analysis of regional myocardial performance in coronary artery disease

NASA Technical Reports Server (NTRS)

Stewart, D. K.; Dodge, H. T.; Frimer, M.

1975-01-01

Findings from a group of subjects with significant coronary artery stenosis are given. A group of controls determined by use of a quantitative method for the study of regional myocardial performance based on the frame-by-frame analysis of biplane left ventricular angiograms are presented. Particular emphasis was placed upon the analysis of wall motion in terms of normalized segment dimensions, timing and velocity of contraction. The results were compared with the method of subjective assessment used clinically.

Detection of Cardiac Quiescence from B-Mode Echocardiography Using a Correlation-Based Frame-to-Frame Deviation Measure

PubMed Central

Mcclellan, James H.; Ravichandran, Lakshminarayan; Tridandapani, Srini

2013-01-01

Two novel methods for detecting cardiac quiescent phases from B-mode echocardiography using a correlation-based frame-to-frame deviation measure were developed. Accurate knowledge of cardiac quiescence is crucial to the performance of many imaging modalities, including computed tomography coronary angiography (CTCA). Synchronous electrocardiography (ECG) and echocardiography data were obtained from 10 healthy human subjects (four male, six female, 23–45 years) and the interventricular septum (IVS) was observed using the apical four-chamber echocardiographic view. The velocity of the IVS was derived from active contour tracking and verified using tissue Doppler imaging echocardiography methods. In turn, the frame-to-frame deviation methods for identifying quiescence of the IVS were verified using active contour tracking. The timing of the diastolic quiescent phase was found to exhibit both inter- and intra-subject variability, suggesting that the current method of CTCA gating based on the ECG is suboptimal and that gating based on signals derived from cardiac motion are likely more accurate in predicting quiescence for cardiac imaging. Two robust and efficient methods for identifying cardiac quiescent phases from B-mode echocardiographic data were developed and verified. The methods presented in this paper will be used to develop new CTCA gating techniques and quantify the resulting potential improvement in CTCA image quality. PMID:26609501

Seismic damage to structures in the M s6.5 Ludian earthquake

NASA Astrophysics Data System (ADS)

Chen, Hao; Xie, Quancai; Dai, Boyang; Zhang, Haoyu; Chen, Hongfu

2016-03-01

On 3 August 2014, the Ludian earthquake struck northwest Yunnan Province with a surface wave magnitude of 6.5. This moderate earthquake unexpectedly caused high fatalities and great economic loss. Four strong motion stations were located in the areas with intensity V, VI, VII and IX, near the epicentre. The characteristics of the ground motion are discussed herein, including 1) ground motion was strong at a period of less than 1.4 s, which covered the natural vibration period of a large number of structures; and 2) the release energy was concentrated geographically. Based on materials collected during emergency building inspections, the damage patterns of adobe, masonry, timber frame and reinforced concrete (RC) frame structures in areas with different intensities are summarised. Earthquake damage matrices of local buildings are also given for fragility evaluation and earthquake damage prediction. It is found that the collapse ratios of RC frame and confined masonry structures based on the new design code are significantly lower than non-seismic buildings. However, the RC frame structures still failed to achieve the `strong column, weak beam' design target. Traditional timber frame structures with a light infill wall showed good aseismic performance.

Pyramidal space frame and associated methods

DOEpatents

Clark, Ryan Michael; White, David; Farr, Jr, Adrian Lawrence

2016-07-19

A space frame having a high torsional strength comprising a first square bipyramid and two planar structures extending outward from an apex of the first square bipyramid to form a "V" shape is disclosed. Some embodiments comprise a plurality of edge-sharing square bipyramids configured linearly, where the two planar structures contact apexes of all the square bipyramids. A plurality of bridging struts, apex struts, corner struts and optional internal bracing struts increase the strength and rigidity of the space frame. In an embodiment, the space frame supports a solar reflector, such as a parabolic solar reflector. Methods of fabricating and using the space frames are also disclosed.

Computer-based Astronomy Labs for Non-science Majors

NASA Astrophysics Data System (ADS)

Smith, A. B. E.; Murray, S. D.; Ward, R. A.

1998-12-01

We describe and demonstrate two laboratory exercises, Kepler's Third Law and Stellar Structure, which are being developed for use in an astronomy laboratory class aimed at non-science majors. The labs run with Microsoft's Excel 98 (Macintosh) or Excel 97 (Windows). They can be run in a classroom setting or in an independent learning environment. The intent of the labs is twofold; first and foremost, students learn the subject matter through a series of informational frames. Next, students enhance their understanding by applying their knowledge in lab procedures, while also gaining familiarity with the use and power of a widely-used software package and scientific tool. No mathematical knowledge beyond basic algebra is required to complete the labs or to understand the computations in the spreadsheets, although the students are exposed to the concepts of numerical integration. The labs are contained in Excel workbook files. In the files are multiple spreadsheets, which contain either a frame with information on how to run the lab, material on the subject, or one or more procedures. Excel's VBA macro language is used to automate the labs. The macros are accessed through button interfaces positioned on the spreadsheets. This is done intentionally so that students can focus on learning the subject matter and the basic spreadsheet features without having to learn advanced Excel features all at once. Students open the file and progress through the informational frames to the procedures. After each procedure, student comments and data are automatically recorded in a preformatted Lab Report spreadsheet. Once all procedures have been completed, the student is prompted for a filename in which to save their Lab Report. The lab reports can then be printed or emailed to the instructor. The files will have full worksheet and workbook protection, and will have a "redo" feature at the end of the lab for students who want to repeat a procedure.

Predicted secondary structure similarity in the absence of primary amino acid sequence homology: hepatitis B virus open reading frames.

PubMed Central

Schaeffer, E; Sninsky, J J

1984-01-01

Proteins that are related evolutionarily may have diverged at the level of primary amino acid sequence while maintaining similar secondary structures. Computer analysis has been used to compare the open reading frames of the hepatitis B virus to those of the woodchuck hepatitis virus at the level of amino acid sequence, and to predict the relative hydrophilic character and the secondary structure of putative polypeptides. Similarity is seen at the levels of relative hydrophilicity and secondary structure, in the absence of sequence homology. These data reinforce the proposal that these open reading frames encode viral proteins. Computer analysis of this type can be more generally used to establish structural similarities between proteins that do not share obvious sequence homology as well as to assess whether an open reading frame is fortuitous or codes for a protein. PMID:6585835

High symptom reporters are less interoceptively accurate in a symptom-related context.

PubMed

Bogaerts, Katleen; Millen, An; Li, Wan; De Peuter, Steven; Van Diest, Ilse; Vlemincx, Elke; Fannes, Stien; Van den Bergh, Omer

2008-11-01

We investigated the role of a symptom interpretation frame on the accuracy of interoception and on retrospective symptom reporting in nonclinical high and low reporters of medically unexplained symptoms. All participants (N=74) went through two subsequent trials of the Rebreathing Test, inducing altered respiration and other physical sensations as a result of a gradually increasing pCO(2) level in the blood. Each trial consisted of a baseline (60 s), a rebreathing phase (150 s), and a recovery phase (150 s). In one trial, the sensations were framed in a neutral way ("the gas mixture might alter breathing behavior and induce respiratory sensations"). In the other trial, a symptom frame was induced ("the gas mixture might alter breathing behavior and induce respiratory symptoms"). Breathing behavior was continuously monitored, subjective sensations were rated every 10 s, and after each trial, participants filled out a symptom checklist. Within-subject correlations between the subjective rating and its physiological referent were calculated for the rebreathing phase and recovery phase of each trial separately. High symptom reporters had more (retrospective) complaints than low symptom reporters, especially in the symptom trial. Only in the symptom frame were high symptom reporters less accurate than low symptom reporters. The reduction in interoceptive accuracy (IA) in high symptom reporters was most striking in the recovery phase of the symptom frame trial. A contextual cue, such as a reference to symptoms, reduced IA in high symptom reporters and this was more so during recovery from the symptom induction.

Full-scale shear wall tests for force transfer around openings

Treesearch

Tom Skaggs; Borjen Yeh; Frank Lam; Douglas Rammer; James Wacker

2010-01-01

Wood structural panel sheathed shear walls and diaphragms are the primary lateral-load resisting elements in wood-frame construction. The historical performance of light-frame structures in North America are very good due, in part, to model building codes that are designed to preserve life safety, as well as the inherent redundancy of wood-frame construction using wood...

Improving stability and strength characteristics of framed structures with nonlinear behavior

NASA Technical Reports Server (NTRS)

Pezeshk, Shahram

1990-01-01

In this paper an optimal design procedure is introduced to improve the overall performance of nonlinear framed structures. The design methodology presented here is a multiple-objective optimization procedure whose objective functions involve the buckling eigenvalues and eigenvectors of the structure. A constant volume with bounds on the design variables is used in conjunction with an optimality criterion approach. The method provides a general tool for solving complex design problems and generally leads to structures with better limit strength and stability. Many algorithms have been developed to improve the limit strength of structures. In most applications geometrically linear analysis is employed with the consequence that overall strength of the design is overestimated. Directly optimizing the limit load of the structure would require a full nonlinear analysis at each iteration which would be prohibitively expensive. The objective of this paper is to develop an algorithm that can improve the limit-load of geometrically nonlinear framed structures while avoiding the nonlinear analysis. One of the novelties of the new design methodology is its ability to efficiently model and design structures under multiple loading conditions. These loading conditions can be different factored loads or any kind of loads that can be applied to the structure simultaneously or independently. Attention is focused on optimal design of space framed structures. Three-dimensional design problems are more complicated to carry out, but they yield insight into real behavior of the structure and can help avoiding some of the problems that might appear in planar design procedure such as the need for out-of-plane buckling constraint. Although researchers in the field of structural engineering generally agree that optimum design of three-dimension building frames especially in the seismic regions would be beneficial, methods have been slow to emerge. Most of the research in this area has dealt with the optimization of truss and plane frame structures.

Subjective quality evaluation of low-bit-rate video

NASA Astrophysics Data System (ADS)

Masry, Mark; Hemami, Sheila S.; Osberger, Wilfried M.; Rohaly, Ann M.

2001-06-01

A subjective quality evaluation was performed to qualify vie4wre responses to visual defects that appear in low bit rate video at full and reduced frame rates. The stimuli were eight sequences compressed by three motion compensated encoders - Sorenson Video, H.263+ and a Wavelet based coder - operating at five bit/frame rate combinations. The stimulus sequences exhibited obvious coding artifacts whose nature differed across the three coders. The subjective evaluation was performed using the Single Stimulus Continuos Quality Evaluation method of UTI-R Rec. BT.500-8. Viewers watched concatenated coded test sequences and continuously registered the perceived quality using a slider device. Data form 19 viewers was colleted. An analysis of their responses to the presence of various artifacts across the range of possible coding conditions and content is presented. The effects of blockiness and blurriness on perceived quality are examined. The effects of changes in frame rate on perceived quality are found to be related to the nature of the motion in the sequence.

49 CFR 396.3 - Inspection, repair, and maintenance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... systematically inspected, repaired, and maintained, all motor vehicles and intermodal equipment subject to its... affect safety of operation, including but not limited to, frame and frame assemblies, suspension systems... cause to be maintained, records for each motor vehicle they control for 30 consecutive days. Intermodal...

Soft storey effects on plastic hinge propagation of moment resisting reinforced concrete building subjected to Ranau earthquake

NASA Astrophysics Data System (ADS)

Tan, Chee Ghuan; Chia, Wei Ting; Majid, Taksiah A.; Nazri, Fadzli Mohamed; Adiyanto, Mohd Irwan

2017-10-01

On 5th June 2015, a moderate earthquake with Mw 5.9 hit Ranau, resulted in damages of the existing non-seismically designed buildings, such that 61 buildings, including mosques, schools, hospitals and Ranau police headquarters were suffered from different level structural damages. Soft storey irregularity is one of the main reasons of the building damage. This study is to investigate the soft-story effect on the propagation path of plastic hinges RC building under seismic excitation. The plastic hinges formation and seismic performance of five moment resisting RC frames with different infill configurations are studied. The seismic performance of building is evaluated by Incremental Dynamic Analysis (IDA). Open ground soft storey structure shows the lowest seismic resistance, collapses at 0.55g pga. The maximum interstorey drift ratio (IDRmax) in soft storey buildings ranging from 0.53% to 2.96% which are far greater than bare frame ranging from 0.095% to 0.69%. The presence of infill walls creates stiffer upper stories causing moments concentrate at the soft storey, resulting the path of plastic hinge propagation is dominant at the soft storey columns. Hence, the buildings with soft storey are very susceptible under earthquake load.

Effect of Various Interface Thicknesses on the Behaviour of Infilled frame Subjected to Lateral Load

NASA Astrophysics Data System (ADS)

Senthil, K.; Muthukumar, S.; Rupali, S.; Satyanarayanan, K. S.

2018-03-01

Two dimensional numerical investigations were carried out to study the influence of interface thickness on the behaviour of reinforced concrete frames subjected to in-plane lateral loads using commercial finite element tool SAP 2000. The cement mortar, cork and foam was used as interface material and their effect was studied by varying thicknesses as 6, 8, 10, 14 and 20 mm. The effect of lateral loads on infill masonry wall was also studied by varying arbitrary loads as 10, 20, 40 and 60 kN. The resistance of the frame with cement mortar was found maximum with the interface thickness 10 mm therefore, it is concluded that the maximum influence of interface thickness of 10 mm was found effective. The resistance of integral infill frame with cork and foam interface was found maximum with the interface thickness 6 mm and it is concluded that 6 mm thick interface among the chosen thickness was found effective.

Lightweight design of automobile frame based on magnesium alloy

NASA Astrophysics Data System (ADS)

Lyu, R.; Jiang, X.; Minoru, O.; Ju, D. Y.

2018-06-01

The structural performance and lightweighting of car base frame design is a challenging task due to all the performance targets that must be satisfied. In this paper, three kinds of materials (iron, aluminum and magnesium alloy) replacement along with section design optimization strategy is proposed to develop a lightweight car frame structure to satisfy the tensile and safety while reducing weight. Two kinds of cross-sections are considered as the design variables. Using Ansys static structure, the design optimization problem is solved, comparing the results of each step, structure of the base flame is optimized for lightweight.

Damage criticality and inspection concerns of composite-metallic aircraft structures under blunt impact

NASA Astrophysics Data System (ADS)

Zou, D.; Haack, C.; Bishop, P.; Bezabeh, A.

2015-04-01

Composite aircraft structures such as fuselage and wings are subject to impact from many sources. Ground service equipment (GSE) vehicles are regarded as realistic sources of blunt impact damage, where the protective soft rubber is used. With the use of composite materials, blunt impact damage is of special interest, since potential significant structural damage may be barely visible or invisible on the structure's outer surface. Such impact can result in local or non-local damage, in terms of internal delamination in skin, interfacial delamination between stiffeners and skin, and fracture of internal reinforced component such as stringers and frames. The consequences of these events result in aircraft damage, delays, and financial cost to the industry. Therefore, it is necessary to understand the criticality of damage under this impact and provide reliable recommendations for safety and inspection technologies. This investigation concerns a composite-metallic 4-hat-stiffened and 5-frame panel, designed to represent a fuselage structure panel generic to the new generation of composite aircraft. The test fixtures were developed based on the correlation between finite element analyses of the panel model and the barrel model. Three static tests at certain amount of impact energy were performed, in order to improve the understanding of the influence of the variation in shear ties, and the added rotational stiffness. The results of this research demonstrated low velocity high mass impacts on composite aircraft fuselages beyond 82.1 kN of impact load, which may cause extensive internal structural damage without clear visual detectability on the external skin surface.

Effectiveness of standing frame on constipation in children with cerebral palsy: a single-subject study.

PubMed

Rivi, Elena; Filippi, Mariacristina; Fornasari, Elisa; Mascia, Maria Teresa; Ferrari, Adriano; Costi, Stefania

2014-09-01

Children with cerebral palsy (CP) and quadriplegia or severe diplegia suffer from highly reduced mobility and consequent constipation. Clinicians recommend standing frames to exercise the support reaction in this population, sharing the opinion that the upright position may facilitate intestinal transit, although no evidence supports this assumption. We conducted this study to determine the effects of the standing frame on spontaneous evacuation in children with CP. Moreover, we studied its effects on the frequency of induction of evacuation, the characteristics of the stool and the pain suffered by the child due to constipation and/or evacuation. We implemented a single-subject research design in one chronically constipated child with CP and quadriplegia, Gross Motor Function Classification System Level V. To monitor the effects of the standing frame, we measured the outcome of interest throughout the study using a daily diary and the Bristol Stool Scale. This study was approved by the local Ethics Committee. This study has several limitation; primarily, the use of a single-subject research design only makes possible the visual analysis of data obtained from a unique patient. So, by themselves, data obtained do not allow us any generalization for the target population. Future research should verify our results collecting more data and also investigating the effect of the standing-frame on respiratory functions. Although the standing frame did not affect the frequency of evacuations or the characteristics of the stool, its employment reduced the inductions of evacuation and the related pain suffered by the child. However, this study has several limitations, such as the lack of generalization due to the fact that we studied a unique patient and the overall brevity of the study due to external circumstances. Therefore, we suggest future research to verify our results, also investigating the effect of the standing frame on respiratory functions. Relevance to clinical practice. The standing frame may positively influence the management of constipation of these children, possibly improving their quality of life. Copyright © 2014 John Wiley & Sons, Ltd.

Characteristics of High School Students' and Science Teachers' Cognitive Frame about Effective Teaching Method for High School Science Subject

NASA Astrophysics Data System (ADS)

Chung, Duk Ho; Park, Kyeong-Jin; Cho, Kyu Seong

2016-04-01

We investigated the cognitive frame of high school students and inservice high school science teachers about effective teaching method, and we also explored how they understood about the teaching methods suggested by the 2009 revised Science Curriculum. Data were collected from 275 high school science teachers and 275 high school students. We analyzed data in terms of the words and the cognitive frame using the Semantic Network Analysis. The results were as follows. First, the teachers perceived that an activity oriented class was the effective science class that helped improve students'' problem-solving abilities and their inquiry skills. The students had the cognitive frame that their teacher had to present relevant and enough teaching materials to students, and that they should also receive assistance from teachers in science class to better prepare for college entrance exam. Second, both students and teachers retained the cognitive frame about the efficient science class that was not reflected 2009 revised Science Curriculum exactly. Especially, neither groups connected the elements of ''convergence'' as well as ''integration'' embedded across science subject areas to their cognitive frame nor cognized the fact that many science learning contents were closed related to one another. Therefore, various professional development opportunities should be offered so that teachers succinctly comprehend the essential features and the intents of the 2009 revised Science Curriculum and thereby implement it in their science lessons effectively. Keywords : semantic network analysis, cognitive frame, teaching method, science lesson

Rib Bone Graft Adjusted to Fit the Facial Asymmetry: A Frame Structure Graft.

PubMed

Lee, Yoon Ho; Choi, Jong Hwan; Hwang, Kun; Choi, Jun Ho

2015-10-01

The authors introduce the concept of a "frame structure graft" in which a harvested rib bone was adjusted to fit facial asymmetry. On the costochondral junction of the sixth or seventh rib, a 5 cm incision was made. Through a subperiosteal dissection, the rib bone was harvested. Using a reciprocating saw, the harvested rib was scored on its anterior surface as well as its posterior surface with a partial depth at different intervals. The harvested rib bone was placed on the skin surface of the unaffected side of the face and a curvature was created exactly matching that of the unaffected side by bending the bone using a greenstick fracture. Thereafter, the graft was adjusted to conceal the asymmetry of the deficient side. The adjusted "frame structure" was transferred to the defect through the incisions on the affected side, and the "frame structure" graft was placed on the mandible or zygoma. The graft fixation was done externally with at least 2 Kirschner wires (K-wires). From January 2005 to August 2013, a total of 30 patients (13 men, 17 women, mean age 25.6 years) received a frame structure graft. All 30 patients achieved good healing at the operation site without complications. Donor-site morbidity as pneumothorax from the rib bone harvest was not found. Merits of this frame structure graft, the authors think, are that this method could allow a similar curvature to the normal side. In addition, the procedure itself is easy.

Engineering science and mechanics; Proceedings of the International Symposium, Tainan, Republic of China, December 29-31, 1981. Parts 1 & 2

NASA Astrophysics Data System (ADS)

Hsia, H.-M.; Chou, Y.-L.; Longman, R. W.

1983-07-01

The topics considered are related to measurements and controls in physical systems, the control of large scale and distributed parameter systems, chemical engineering systems, aerospace science and technology, thermodynamics and fluid mechanics, and computer applications. Subjects in structural dynamics are discussed, taking into account finite element approximations in transient analysis, buckling finite element analysis of flat plates, dynamic analysis of viscoelastic structures, the transient analysis of large frame structures by simple models, large amplitude vibration of an initially stressed thick plate, nonlinear aeroelasticity, a sensitivity analysis of a combined beam-spring-mass structure, and the optimal design and aeroelastic investigation of segmented windmill rotor blades. Attention is also given to dynamics and control of mechanical and civil engineering systems, composites, and topics in materials. For individual items see A83-44002 to A83-44061

Indoor magnetic navigation for the blind.

PubMed

Riehle, Timothy H; Anderson, Shane M; Lichter, Patrick A; Giudice, Nicholas A; Sheikh, Suneel I; Knuesel, Robert J; Kollmann, Daniel T; Hedin, Daniel S

2012-01-01

Indoor navigation technology is needed to support seamless mobility for the visually impaired. This paper describes the construction of and evaluation of a navigation system that infers the users' location using only magnetic sensing. It is well known that the environments within steel frame structures are subject to significant magnetic distortions. Many of these distortions are persistent and have sufficient strength and spatial characteristics to allow their use as the basis for a location technology. This paper describes the development and evaluation of a prototype magnetic navigation system consisting of a wireless magnetometer placed at the users' hip streaming magnetic readings to a smartphone processing location algorithms. Human trials were conducted to assess the efficacy of the system by studying route-following performance with blind and sighted subjects using the navigation system for real-time guidance.

Framing curriculum discursively: theoretical perspectives on the experience of VCE physics

NASA Astrophysics Data System (ADS)

Hart, Christina

2002-10-01

The process of developing prescribed curricula has been subject to little empirical investigation, and there have been few attempts to develop theoretical frameworks for understanding the shape and content of particular subjects. This paper presents an account of the author's experience of developing a new course for school physics in the State of Victoria, Australia, at the end of the 1980s. The course was to represent a significant departure from traditional physics courses, and was intended to broaden participation and improve the quality of student learning. In the event the new course turned out to be very similar to traditional courses in Physics. The paper explores the reasons for this outcome. Some powerful discursive mechanisms are identified and some implications of post-structuralism for the theoretical understanding of curriculum are discussed.

Seismic Performance Evaluation of Reinforced Concrete Frames Subjected to Seismic Loads

NASA Astrophysics Data System (ADS)

Zameeruddin, Mohd.; Sangle, Keshav K.

2017-06-01

Ten storied-3 bays reinforced concrete bare frame designed for gravity loads following the guidelines of IS 456 and IS 13920 for ductility is subjected to seismic loads. The seismic demands on this building were calculated by following IS 1893 for response spectra of 5% damping (for hard soil type). Plastic hinges were assigned to the beam and column at both ends to represent the failure mode, when member yields. Non-linear static (pushover) analysis was performed to evaluate the performance of the building in reference to first (ATC 40), second (FEMA 356) and next-generation (FEMA 440) performance based seismic design procedures. Base shear against top displacement curve of structure, known as pushover curve was obtained for two actions of plastic hinge behavior, force-controlled (brittle) and deformation-controlled (ductile) actions. Lateral deformation corresponding to performance point proves the building capability to sustain a certain level of seismic loads. The failure is represented by a sequence of formation of plastic hinges. Deformation-controlled action of hinges showed that building behaves like strong-column-weak-beam mechanism, whereas force-controlled action showed formation of hinges in the column. The study aims to understand the first, second and next generation performance based design procedure in prediction of actual building responses and their conservatism into the acceptance criteria.

A novel key-frame extraction approach for both video summary and video index.

PubMed

Lei, Shaoshuai; Xie, Gang; Yan, Gaowei

2014-01-01

Existing key-frame extraction methods are basically video summary oriented; yet the index task of key-frames is ignored. This paper presents a novel key-frame extraction approach which can be available for both video summary and video index. First a dynamic distance separability algorithm is advanced to divide a shot into subshots based on semantic structure, and then appropriate key-frames are extracted in each subshot by SVD decomposition. Finally, three evaluation indicators are proposed to evaluate the performance of the new approach. Experimental results show that the proposed approach achieves good semantic structure for semantics-based video index and meanwhile produces video summary consistent with human perception.

Inertial Frames Without the Relativity Principle: Breaking Lorentz Symmetry

NASA Astrophysics Data System (ADS)

Baccetti, Valentina; Tate, Kyle; Visser, Matt

2015-01-01

We investigate inertial frames in the absence of Lorentz invariance, reconsidering the usual group structure implied by the relativity principle. We abandon the relativity principle, discarding the group structure for the transformations between inertial frames, while requiring these transformations to be at least linear (to preserve homogeneity). In theories with a preferred frame (aether), the set of transformations between inertial frames forms a groupoid/pseudogroup instead of a group, a characteristic essential to evading the von Ignatowsky theorems. In order to understand the dynamics, we also demonstrate that the transformation rules for energy and momentum are in general affine. We finally focus on one specific and compelling model implementing a minimalist violation of Lorentz invariance.

Structural design and performance of a rear support walking frame.

PubMed

Woollam, P J; Miller, K; McLeod, N; Batty, D; Stallard, J

2002-01-01

Rear support walking frames provide predetermined vertical support for patients with dysfunctional lower limbs that have limited active control; the support is provided through a spring-loaded boom hinged on an upright stanchion mounted at the rear of a wheeled frame within which the patient ambulates. The application of these frames for total-body-involved cerebral palsy patients, in combination with a walking orthosis, has highlighted a number of practical problems that need to be addressed for the system to become fully viable. A composite material prototype walking frame has been developed that permits the patient to be transferred by a single carer without the need to use inappropriate manual handling techniques. The frame has improved structural properties, with stiffness in the sagittal and coronal planes increasing by between 50 and 100 per cent. Evaluation with patients showed that the greater structural stiffness permitted the objective of improved continuity of walking to be achieved. The strength of the frame is such that it can accommodate patients of up to 80 kg, more than twice that possible in the earlier system. Since the structural yield point is approximately twice the maximum working load, the device should not be prone to unacceptable fatigue characteristics. Despite the use of carbon composite materials (which have brittle failure characteristics), the mode of failure is of progressive collapse and is therefore inherently safe. The successful outcome of prototype testing has justified production development. Work is now proceeding on a design that incorporates further improvements in structural performance and ease of manufacture.

A preliminary structural analysis of space-based inflatable tubular frame structures

NASA Technical Reports Server (NTRS)

Main, John A.; Peterson, Steven W.; Strauss, Alvin M.

1992-01-01

The use of inflatable structures has often been proposed for aerospace and planetary applications. The advantages of such structures include low launch weight and easy assembly. The use of inflatables for applications requiring very large frame structures intended for aerospace use are proposed. In order to consider using an inflated truss, the structural behavior of the inflated frame must be examined. The statics of inflated tubes as beams was discussed in the literature, but the dynamics of these elements has not received much attention. In an effort to evaluate the vibration characteristics of the inflated beam a series of free vibration tests of an inflated fabric cantilevers were performed. Results of the tests are presented and models for system behavior posed.

Analysis of the Shear Behavior of Stubby Y-Type Perfobond Rib Shear Connectors for a Composite Frame Structure.

PubMed

Kim, Sang-Hyo; Kim, Kun-Soo; Lee, Do-Hoon; Park, Jun-Seung; Han, Oneil

2017-11-22

Shear connectors are used in steel beam-concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. Thus, this paper proposes stubby Y-type perfobond rib shear connectors, redefining the existing connectors, for composite frames of building structures; these were used to perform push-out tests. These shear connectors have relatively small ribs compared to the conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

On implementation of the extended interior penalty function. [optimum structural design

NASA Technical Reports Server (NTRS)

Cassis, J. H.; Schmit, L. A., Jr.

1976-01-01

The extended interior penalty function formulation is implemented. A rational method for determining the transition between the interior and extended parts is set forth. The formulation includes a straightforward method for avoiding design points with some negative components, which are physically meaningless in structural analysis. The technique, when extended to problems involving parametric constraints, can facilitate closed form integration of the penalty terms over the most important parts of the parameter interval. The method lends itself well to the use of approximation concepts, such as design variable linking, constraint deletion and Taylor series expansions of response quantities in terms of design variables. Examples demonstrating the algorithm, in the context of planar orthogonal frames subjected to ground motion, are included.

Design of a space shuttle structural dynamics model

NASA Technical Reports Server (NTRS)

1972-01-01

A 1/8 scale structural dynamics model of a parallel burn space shuttle has been designed. Basic objectives were to represent the significant low frequency structural dynamic characteristics while keeping the fabrication costs low. The model was derived from the proposed Grumman Design 619 space shuttle. The design includes an orbiter, two solid rocket motors (SRM) and an external tank (ET). The ET consists of a monocoque LO2 tank an interbank skirt with three frames to accept SRM attachment members, an LH2 tank with 10 frames of which 3 provide for orbiter attachment members, and an aft skirt with on frame to provide for aft SRM attachment members. The frames designed for the SRM attachments are fitted with transverse struts to take symmetric loads.

Life comparative analysis of energy consumption and CO₂ emissions of different building structural frame types.

PubMed

Kim, Sangyong; Moon, Joon-Ho; Shin, Yoonseok; Kim, Gwang-Hee; Seo, Deok-Seok

2013-01-01

The objective of this research is to quantitatively measure and compare the environmental load and construction cost of different structural frame types. Construction cost also accounts for the costs of CO₂ emissions of input materials. The choice of structural frame type is a major consideration in construction, as this element represents about 33% of total building construction costs. In this research, four constructed buildings were analyzed, with these having either reinforced concrete (RC) or steel (S) structures. An input-output framework analysis was used to measure energy consumption and CO₂ emissions of input materials for each structural frame type. In addition, the CO₂ emissions cost was measured using the trading price of CO₂ emissions on the International Commodity Exchange. This research revealed that both energy consumption and CO₂ emissions were, on average, 26% lower with the RC structure than with the S structure, and the construction costs (including the CO₂ emissions cost) of the RC structure were about 9.8% lower, compared to the S structure. This research provides insights through which the construction industry will be able to respond to the carbon market, which is expected to continue to grow in the future.

Popcorn Story Frames from a Multicultural Perspective.

ERIC Educational Resources Information Center

DiLella, Carol Ann

Popcorn story frames from a multicultural perspective are holistic outlines that in the reading/writing process facilitate comprehension for all cultures learning to read and write stories. Popcorn story frames are structured and modeled in a horizontal fashion just like popcorn pops in a horizontal fashion. The frames are designed for learners…

Evaluation and the Framing of Race

ERIC Educational Resources Information Center

House, Ernest R.

2017-01-01

Racial framing can have strong effects on programs, policies, and even evaluations. Racial framing developed as a justification for the exploitation of minorities and has been a primary causal factor in the persistence of racism. By being aware of its pattern, structure, origins, and how racial framing generates effects, we can significantly…

Battery Berry Observation Station, detail, frame structure meeting older masonry ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Battery Berry Observation Station, detail, frame structure meeting older masonry building on west side of structure; view east - Fort McKinley, Battery Berry Observation Station, North side of Wood Side Drive approximately 80 feet east of Spring Cove Lane, Great Diamond Island, Portland, Cumberland County, ME

A happier and less sinister past, a more hedonistic and less fatalistic present and a more structured future: time perspective and well-being.

PubMed

Sailer, Uta; Rosenberg, Patricia; Nima, Ali Al; Gamble, Amelie; Gärling, Tommy; Archer, Trevor; Garcia, Danilo

2014-01-01

Background. Previous studies have established a link between how people relate to their past, present, and future (i.e., time perspective) and subjective well-being (i.e., life satisfaction, positive and negative affect). Time perspective comprises five dimensions: Past Positive, Past Negative, Present Hedonistic, Present Fatalistic, and Future. Life satisfaction can also be evaluated in relation to different time frames. Moreover, approach related positive affect is associated to a different concept of well-being labeled psychological well-being. In the present study we extend previous findings by investigating the effect of time perspective on the time frame of evaluations of life satisfaction (past, present, future) and by investigating the relationship between time perspective and psychological well-being. Method. Questionnaires on time perspective (Zimbardo's Time Perspective Inventory), temporal life satisfaction (Temporal Satisfaction with Life Scale), affect (Positive Affect and Negative Affect Schedule), and psychological well-being (Scales of Psychological Well-Being-short version) were answered by 453 individuals. Two different structural equation models were tested, one of the relationship between time perspective and temporal life satisfaction, and the other of the relationship between time perspective, affect and psychological well-being. Results. Time perspective affected life satisfaction depending on the time scale on which it was evaluated-memory of a negative past influenced life satisfaction in all time frames, and a positive view of the past influenced both past and future life satisfaction. Moreover, less rumination about past negative events (i.e., low score on Past Negative), the tendency to take risks in the present to achieve happy feelings and/or avoid boredom (i.e., high scores on Present Hedonistic), and a less hopeless and pessimistic view about the present (low scores on Present Fatalistic) were associated with higher levels of psychological well-being and positive affect. These same time perspective dimensions were associated with lower levels of negative affect. The Future time perspective dimension (i.e., approaching life with self-control, punctuality, and planning for the future) was associated with both psychological well-being and positive affect. Conclusions. High levels of both subjective and psychological well-being are related to a happier and a less sinister past, a more hedonistic and less fatalistic present, as well as to a more structured future.

A happier and less sinister past, a more hedonistic and less fatalistic present and a more structured future: time perspective and well-being

PubMed Central

Sailer, Uta; Rosenberg, Patricia; Nima, Ali Al; Gamble, Amelie; Gärling, Tommy; Archer, Trevor

2014-01-01

Background. Previous studies have established a link between how people relate to their past, present, and future (i.e., time perspective) and subjective well-being (i.e., life satisfaction, positive and negative affect). Time perspective comprises five dimensions: Past Positive, Past Negative, Present Hedonistic, Present Fatalistic, and Future. Life satisfaction can also be evaluated in relation to different time frames. Moreover, approach related positive affect is associated to a different concept of well-being labeled psychological well-being. In the present study we extend previous findings by investigating the effect of time perspective on the time frame of evaluations of life satisfaction (past, present, future) and by investigating the relationship between time perspective and psychological well-being. Method. Questionnaires on time perspective (Zimbardo’s Time Perspective Inventory), temporal life satisfaction (Temporal Satisfaction with Life Scale), affect (Positive Affect and Negative Affect Schedule), and psychological well-being (Scales of Psychological Well-Being—short version) were answered by 453 individuals. Two different structural equation models were tested, one of the relationship between time perspective and temporal life satisfaction, and the other of the relationship between time perspective, affect and psychological well-being. Results. Time perspective affected life satisfaction depending on the time scale on which it was evaluated—memory of a negative past influenced life satisfaction in all time frames, and a positive view of the past influenced both past and future life satisfaction. Moreover, less rumination about past negative events (i.e., low score on Past Negative), the tendency to take risks in the present to achieve happy feelings and/or avoid boredom (i.e., high scores on Present Hedonistic), and a less hopeless and pessimistic view about the present (low scores on Present Fatalistic) were associated with higher levels of psychological well-being and positive affect. These same time perspective dimensions were associated with lower levels of negative affect. The Future time perspective dimension (i.e., approaching life with self-control, punctuality, and planning for the future) was associated with both psychological well-being and positive affect. Conclusions. High levels of both subjective and psychological well-being are related to a happier and a less sinister past, a more hedonistic and less fatalistic present, as well as to a more structured future. PMID:24688878

Magnetization transfer and adiabatic R 1ρ MRI in the brainstem of Parkinson's disease.

PubMed

Tuite, Paul J; Mangia, Silvia; Tyan, Andrew E; Lee, Michael K; Garwood, Michael; Michaeli, Shalom

2012-06-01

In addition to classic midbrain pathology, Parkinson's disease (PD) is accompanied by changes in pontine and medullary brainstem structures. These additional abnormalities may underlie non-motor features as well as play a role in motor disability. Using novel magnetic resonance imaging (MRI) methods based on rotating frame adiabatic R(1ρ) (i.e., measurements of longitudinal relaxation during adiabatic full passage pulses) and modified magnetization transfer (MT) MRI mapping, we sought to identify brainstem alterations in nine individuals with mild-moderate PD (off medication) and ten age-matched controls at 4 T. We discovered significant differences in MRI parameters between midbrain and medullary brainstem structures in control subjects as compared to PD patients. These findings support the presence of underlying functional/structural brainstem changes in mild-moderate PD. Copyright © 2012 Elsevier Ltd. All rights reserved.

Spatial vision within egocentric and exocentric frames of reference

NASA Technical Reports Server (NTRS)

Howard, Ian P.

1989-01-01

The extent to which perceptual judgements within egocentric and exocentric frames of reference are subject to illusory disturbances and long term modifications is discussed. It is argued that well known spatial illusions, such as the oculogyral illusion and induced visual motion have usually been discussed without proper attention being paid to the frame of reference within which they occur, and that this has led to the construction of inadequate theories and inappropriate procedures for testing them.

Photon and a preferred frame scenario

NASA Astrophysics Data System (ADS)

Rembieliński, Jakub; Ciborowski, Jacek

2018-06-01

Structure of the space of photonic states is discussed in the context of a working hypothesis of existence of a preferred frame for photons. Two polarization experiments are proposed to test the preferred frame scenario.

Dendritic Core-Frame and Frame Multimetallic Rhombic Dodecahedra: A Comparison Study of Composition and Structure Effects on Electrocatalysis of Methanol Oxidation

DOE PAGES

Mathurin, Leanne E.; Tao, Jing; Xin, Huolin; ...

2017-11-03

The composition and structure of multimetallic nanostructures can be tailored to enhance electrocatalytic properties. This work reports a seed-mediated synthesis of novel multimetallic dendritic core-frame and frame nanostructures with a rhombic dodecahedral shape for enhanced methanol oxidation reaction (MOR). The synthesis involves in situ formation of Cu seeds and the subsequent selective deposition of Pt and Ru on the edges and vertices of the Cu seeds to generate CuPt and CuPtRu dendritic core-frame nanostructures. The core-frame nanostructures undergo a post acetic acid etching process to form the frame nanostructures. While transmission electron microscopy reveals the morphology and elemental distribution ofmore » the nanostructures, X-ray diffraction patterns confirm the alloy compositions of dendritic frames for both the core-frame and frame nanostructures. Compared to the bimetallic CuPt nanostructures, the trimetallic CuPtRu nanostructures lower the onset potential and completely suppress the peak current in the reverse scan for MOR. The CuPtRu alloyed frame nanostructures are the best to prevent Ru leaching compared to the CuPtRu core-frame nanostructures and PtRu catalysts. X-ray photoelectron spectroscopy reveals that all three elements become more electron rich in the frame nanostructures. Thus, further refining the composition ratio of the CuPtRu alloyed dendritic frame nanostructures can lead to more efficient catalysts at a lower cost for MOR.« less

Dendritic Core-Frame and Frame Multimetallic Rhombic Dodecahedra: A Comparison Study of Composition and Structure Effects on Electrocatalysis of Methanol Oxidation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mathurin, Leanne E.; Tao, Jing; Xin, Huolin

The composition and structure of multimetallic nanostructures can be tailored to enhance electrocatalytic properties. This work reports a seed-mediated synthesis of novel multimetallic dendritic core-frame and frame nanostructures with a rhombic dodecahedral shape for enhanced methanol oxidation reaction (MOR). The synthesis involves in situ formation of Cu seeds and the subsequent selective deposition of Pt and Ru on the edges and vertices of the Cu seeds to generate CuPt and CuPtRu dendritic core-frame nanostructures. The core-frame nanostructures undergo a post acetic acid etching process to form the frame nanostructures. While transmission electron microscopy reveals the morphology and elemental distribution ofmore » the nanostructures, X-ray diffraction patterns confirm the alloy compositions of dendritic frames for both the core-frame and frame nanostructures. Compared to the bimetallic CuPt nanostructures, the trimetallic CuPtRu nanostructures lower the onset potential and completely suppress the peak current in the reverse scan for MOR. The CuPtRu alloyed frame nanostructures are the best to prevent Ru leaching compared to the CuPtRu core-frame nanostructures and PtRu catalysts. X-ray photoelectron spectroscopy reveals that all three elements become more electron rich in the frame nanostructures. Thus, further refining the composition ratio of the CuPtRu alloyed dendritic frame nanostructures can lead to more efficient catalysts at a lower cost for MOR.« less

A Bayesian Account of Visual–Vestibular Interactions in the Rod-and-Frame Task

PubMed Central

de Brouwer, Anouk J.; Medendorp, W. Pieter

2016-01-01

Abstract Panoramic visual cues, as generated by the objects in the environment, provide the brain with important information about gravity direction. To derive an optimal, i.e., Bayesian, estimate of gravity direction, the brain must combine panoramic information with gravity information detected by the vestibular system. Here, we examined the individual sensory contributions to this estimate psychometrically. We asked human subjects to judge the orientation (clockwise or counterclockwise relative to gravity) of a briefly flashed luminous rod, presented within an oriented square frame (rod-in-frame). Vestibular contributions were manipulated by tilting the subject’s head, whereas visual contributions were manipulated by changing the viewing distance of the rod and frame. Results show a cyclical modulation of the frame-induced bias in perceived verticality across a 90° range of frame orientations. The magnitude of this bias decreased significantly with larger viewing distance, as if visual reliability was reduced. Biases increased significantly when the head was tilted, as if vestibular reliability was reduced. A Bayesian optimal integration model, with distinct vertical and horizontal panoramic weights, a gain factor to allow for visual reliability changes, and ocular counterroll in response to head tilt, provided a good fit to the data. We conclude that subjects flexibly weigh visual panoramic and vestibular information based on their orientation-dependent reliability, resulting in the observed verticality biases and the associated response variabilities. PMID:27844055

Designing Anti-Binge Drinking Prevention Messages: Message Framing vs. Evidence Type.

PubMed

Kang, Hannah; Lee, Moon J

2017-09-27

We investigated whether presenting anti-binge drinking health campaign messages in different message framing and evidence types influences college students' intention to avoid binge drinking, based on prospect theory (PT) and exemplification theory. A 2 (message framing: loss-framed message/gain-framed message) X 2 (evidence type: statistical/narrative) between-subjects factorial design with a control group was conducted with 156 college students. College students who were exposed to the loss-framed message condition exhibited a higher level of intention to avoid binge drinking in the near future than those who did not see any messages (the control group). This finding was mainly among non-binge drinkers. Regardless of evidence type, those who were exposed to the messages exhibited a higher level of intention to avoid binge drinking than those in the control group. This is also mainly among non-binge drinkers. We also found the main effects of message framing and evidence type on attitude toward the message and the main effect of message framing on attitude toward drinking.

Communicating Inequalities to Enhance Support for Obesity-Prevention Policies: The Role of Social Comparisons, Age Frames, and Emotion.

PubMed

Skurka, Chris

2017-11-28

With certain populations in the United States at higher risk for obesity than other populations, public health advocates have attempted to draw attention to these inequalities to galvanize support for obesity-mitigation policies. Yet research comparing different messages about social inequalities indicates that not all social comparisons are persuasive. Drawing on Weiner's (1986) theory of perceived responsibility and social motivation, I experimentally tested promising message frames about obesity disparities. Participants (N = 653) read one of six messages following a 3 (social comparison frame: geographic vs. racial vs. no-comparison) × 2 (age frame: child vs. adult) between-subjects design. Unexpectedly, geographic frames (rural/urban) indirectly decreased policy support relative to the control frame by way of increased counterarguing. Compared to adult frames about obesity inequalities, childhood frames evoked more sympathy and less internal attribution, which in turn positively predicted support for obesity-prevention policies. Practical and theoretical implications of these findings are discussed.

Seismic Rehabilitation of RC Frames by Using Steel Panels

NASA Astrophysics Data System (ADS)

Mowrtage, Waiel

2008-07-01

Every major earthquake in Turkey causes a large number of building suffer moderate damage due to poor construction. If a proper and fast retrofit is not applied, the aftershocks, which may sometimes come days or weeks after the main shock, can push a moderately damaged building into a major damage or even total collapse. This paper presents a practical retrofit method for moderately damaged buildings, which increases the seismic performance of the structural system by reducing the displacement demand. Fabricated steel panels are used for the retrofit. They are light-weight, easy to handle, and can be constructed very quickly. Moreover, they are cheap, and do not need formwork or skilled workers. They can be designed to compensate for the stiffness and strength degradation, and to fit easily inside a moderately damaged reinforced concrete frame. To test the concept, a half-scale, single-story 3D reinforced concrete frame specimen was constructed at the shake-table laboratories of the Kandilli Observatory and Earthquake Research Institute of Bogazici University, and subjected to recorded real earthquake base accelerations. The amplitudes of base accelerations were increased until a moderate damage level is reached. Then, the damaged RC frames was retrofitted by means of steel panels and tested under the same earthquake. The seismic performance of the specimen before and after the retrofit was evaluated using FEMA356 standards, and the results were compared in terms of stiffness, strength, and deformability. The results have confirmed effectiveness of the proposed retrofit scheme.

Re-conceptualizing stress: Shifting views on the consequences of stress and its effects on stress reactivity.

PubMed

Liu, Jenny J W; Vickers, Kristin; Reed, Maureen; Hadad, Marilyn

2017-01-01

The consequences of stress are typically regarded from a deficit-oriented approach, conceptualizing stress to be entirely negative in its outcomes. This approach is unbalanced, and may further hinder individuals from engaging in adaptive coping. In the current study, we explored whether negative views and beliefs regarding stress interacted with a stress framing manipulation (positive, neutral and negative) on measures of stress reactivity for both psychosocial and physiological stressors. Ninety participants were randomized into one of three framing conditions that conceptualized the experience of stress in balanced, unbalanced-negative or unbalanced-positive ways. After watching a video on stress, participants underwent a psychosocial (Trier Social Stress Test), or a physiological (CO2 challenge) method of stress-induction. Subjective and objective markers of stress were assessed. Most of the sampled population regarded stress as negative prior to framing. Further, subjective and objective reactivity were greater to the TSST compared to the CO2 challenge. Additionally, significant cubic trends were observed in the interactions of stress framing and stress-induction methodologies on heart rate and blood pressure. Balanced framing conditions in the TSST group had a significantly larger decrease in heart rate and diastolic blood pressure following stress compared to the positive and negative framing conditions. Findings confirmed a deficit-orientation of stress within the sampled population. In addition, results highlighted the relative efficacy of the TSST compared to CO2 as a method of stress provocation. Finally, individuals in framing conditions that posited stress outcomes in unbalanced manners responded to stressors less efficiently. This suggests that unbalanced framing of stress may have set forth unrealistic expectations regarding stress that later hindered individuals from adaptive responses to stress. Potential benefits of alternative conceptualizations of stress on stress reactivity are discussed, and suggestions for future research are made.

Voices of disability on the radio.

PubMed

O'Malley, Mary Pat

2008-01-01

While much commentary exists in relation to the portrayal of disabled people in the media, very little research examines the talk itself in any detail. This paper examines the how people with communication disabilities and disabled people are dealt with in the talk of a radio programme about disability. To show how the voices of disabled people, and in particular people with communication difficulties, are dealt with on a radio programme titled For and About People with Disability (http://www.rte.ie). Analysis of 15 episodes of an Irish radio programme for and about people with disability called Outside the Box to identify frames governing the discourse. Three frames are identified: radio programme frame; presenter frame; and interview frame. Communication disability never appears as a topic in the radio programme frame. In the presenter and interview frames the presenter foregrounds medical aspects of experiences, asks questions that only seek factual information, and fails to respond to subjective aspects of disabled people's experiences. Analysis of the interviewees' responses show how they hold the floor and introduce subjective accounts of living with disability. Frame analysis reveals how disability (including communication disability) is dealt with in the talk of a radio programme for and about people with disability. There is an overemphasis on medical aspects of disability and a view of disability as a primarily physical phenomenon is broadcast. In spite of mainly medical/factual questions, interviewees manage to include rich accounts of their experience. People with communication disability are not included, possibly due to issues of intelligibility or lack of awareness. Speech and language therapists have a valuable role to play in terms of 'learning to listen' and 'helping to tell'.

Compliant walker

NASA Technical Reports Server (NTRS)

Kerley, James J. (Inventor); Eklund, Wayne D. (Inventor); Crane, J. Allen (Inventor)

1992-01-01

A compliant walker is provided for humans having limited use of their legs and lower back. It includes an upright wheel frame which at least partially surrounds an upright user wearing a partial body harness. It is attached to the frame by means of cable compliant apparatus consisting of sets of cable segments and angle bracket members connected between opposite side members of the frame and adjacent side portions of the harness. Novelty is believed to exist in the combination of a wheeled frame including a side support structure, a body harness, and compliance means connecting the body harness to the side support structure for flexibility holding and supporting a person in a substantially upright position when the user sags in the frame when taking weight off the lower extremities.

Present capabilities and future requirements for computer-aided geometric modeling in the design and manufacture of gas turbine

NASA Technical Reports Server (NTRS)

Caille, E.; Propen, M.; Hoffman, A.

1984-01-01

Gas turbine engine design requires the ability to rapidly develop complex structures which are subject to severe thermal and mechanical operating loads. As in all facets of the aerospace industry, engine designs are constantly driving towards increased performance, higher temperatures, higher speeds, and lower weight. The ability to address such requirements in a relatively short time frame has resulted in a major thrust towards integrated design/analysis/manufacturing systems. These computer driven graphics systems represent a unique challenge, with major payback opportunities if properly conceived, implemented, and applied.

Effect of framing on adolescents' decision making.

PubMed

Chien, Y C; Lin, C; Worthley, J

1996-12-01

92 young adolescents were tested using Tversky and Kahneman's (1981) decision problems for framing effects. A notable number of young adolescents tested were not influenced by the context of the decision problems, thus they selected the same response option for positively and negatively framed problems. Parallel information was not available in Tversky and Kahneman's study for adults because they used a between-subjects design. However, for present adolescents who selected different response options for different framing problems, the response pattern exhibited by them resembled the general pattern exhibited by the adults tested in Tversky and Kahneman's study-negative frames led them to accept risk to avoid certain loss; positive frames prevented them from risking what they were certain to gain. Boys and girls were similar in their susceptibility to framing effects as were honors students in mathematics as compared to nonhonors students. Although the positive vs negative framing only influenced some of the young adolescents tested in this study, because the influence was consistent, researchers and educators interested in adolescents' decisions involving risky choices might use framing principles to design and assess cognitive interventions for high-risk behaviors among young adolescents.

Design optimization of the S-frame to improve crashworthiness

NASA Astrophysics Data System (ADS)

Liu, Shu-Tian; Tong, Ze-Qi; Tang, Zhi-Liang; Zhang, Zong-Hua

2014-08-01

In this paper, the S-frames, the front side rail structures of automobile, were investigated for crashworthiness. Various cross-sections including regular polygon, non-convex polygon and multi-cell with inner stiffener sections were investigated in terms of energy absorption of S-frames. It was determined through extensive numerical simulation that a multi-cell S-frame with double vertical internal stiffeners can absorb more energy than the other configurations. Shape optimization was also carried out to improve energy absorption of the S-frame with a rectangular section. The center composite design of experiment and the sequential response surface method (SRSM) were adopted to construct the approximate design sub-problem, which was then solved by the feasible direction method. An innovative double S-frame was obtained from the optimal result. The optimum configuration of the S-frame was crushed numerically and more plastic hinges as well as shear zones were observed during the crush process. The energy absorption efficiency of the structure with the optimal configuration was improved compared to the initial configuration.

Frame for a firearm

DOEpatents

Crandall, David L [Idaho Falls, ID; Watson, Richard W [Blackfoot, ID

2008-03-04

A firearm frame which is adapted to be disposed in operative relationship as a component part of a firearm, the firearm having disposed in operative relationships each with one or more of the others, a barrel, a receiver, and at least one firing mechanism; wherein the barrel and receiver form operative parts of a movable assembly and the at least one firing mechanism is disposed in a substantially stationary operative relationship therewith; the firearm frame including at least one elongated support structure discrete from the barrel and receiver, the elongated support structure being adapted to directly support the movable assembly in an operative movable relationship therewith; whereby at least one of the barrel and receiver is in direct contact with and movable on the elongated support structure; and, a firing mechanism support structure connected to the at least one elongated support structure, the firing mechanism support structure being adapted to have the firing mechanism connected thereto; the firearm frame also directly supporting the movable assembly and the firing mechanism in corresponding movable and stationary operative relationships each with the other.

Design and strength analysis of a fertilizing and soil covering vehicle

NASA Astrophysics Data System (ADS)

Sun, Heng-Hui; Zhang, Zheng-Yong; Liu, Yang; Zhu, Li-Kai; Chen, En-Wei

2018-03-01

In this paper, a kind of fertilizing and soil covering vehicle is designed with compact structure, easy control and substituting manual work to conduct the operations including fertilizing and soil covering. In accordance with movement, structure and loading feature of fertilizing and soil covering vehicle, parametric modeling is carried out for the frame part of this fertilizing and soil covering vehicle to define boundary conditions such as load, constraint, etc. when the frame is under the working condition of normal full load. ANSYS software is used to produce finite element model of frame, and to analyze and solve the model, so as to obtain stress and stain variation diagram of each part of frame under working condition of normal full load. The calculation result shows that: the structure of frame is able to meet the strength requirement, and the maximum value of stress is located at joint between frame and external hinge, which should be appropriately improved in thickening way. In addition, a larger deformation occurring at damper on lower part of hopper may be reduced by adding rib plate at damper on lower part of hopper. The research result of this paper provides the theoretical basis for the design of frame of fertilizing and soil covering vehicle, which has deep theoretical significance and application value.

Seismic performance evaluation of an infilled rocking wall frame structure through quasi-static cyclic testing

NASA Astrophysics Data System (ADS)

Pan, Peng; Wu, Shoujun; Wang, Haishen; Nie, Xin

2018-04-01

Earthquake investigations have illustrated that even code-compliant reinforced concrete frames may suffer from soft-story mechanism. This damage mode results in poor ductility and limited energy dissipation. Continuous components offer alternatives that may avoid such failures. A novel infilled rocking wall frame system is proposed that takes advantage of continuous component and rocking characteristics. Previous studies have investigated similar systems that combine a reinforced concrete frame and a wall with rocking behavior used. However, a large-scale experimental study of a reinforced concrete frame combined with a rocking wall has not been reported. In this study, a seismic performance evaluation of the newly proposed infilled rocking wall frame structure was conducted through quasi-static cyclic testing. Critical joints were designed and verified. Numerical models were established and calibrated to estimate frame shear forces. The results evaluation demonstrate that an infilled rocking wall frame can effectively avoid soft-story mechanisms. Capacity and initial stiffness are greatly improved and self-centering behavior is achieved with the help of the infilled rocking wall. Drift distribution becomes more uniform with height. Concrete cracks and damage occurs in desired areas. The infilled rocking wall frame offers a promising approach to achieving seismic resilience.

How chimpanzees (Pan troglodytes) perform in a modified emotional Stroop task.

PubMed

Allritz, Matthias; Call, Josep; Borkenau, Peter

2016-05-01

The emotional Stroop task is an experimental paradigm developed to study the relationship between emotion and cognition. Human participants required to identify the color of words typically respond more slowly to negative than to neutral words (emotional Stroop effect). Here we investigated whether chimpanzees (Pan troglodytes) would show a comparable effect. Using a touch screen, eight chimpanzees were trained to choose between two simultaneously presented stimuli based on color (two identical images with differently colored frames). In Experiment 1, the images within the color frames were shapes that were either of the same color as the surrounding frame or of the alternative color. Subjects made fewer errors and responded faster when shapes were of the same color as the frame surrounding them than when they were not, evidencing that embedded images affected target selection. Experiment 2, a modified version of the emotional Stroop task, presented subjects with four different categories of novel images: three categories of pictures of humans (veterinarian, caretaker, and stranger), and control stimuli showing a white square. Because visits by the veterinarian that include anaesthetization can be stressful for subjects, we expected impaired performance in trials presenting images of the veterinarian. For the first session, we found correct responses to be indeed slower in trials of this category. This effect was more pronounced for subjects whose last anaesthetization experience was more recent, indicating that emotional valence caused the slowdown. We propose our modified emotional Stroop task as a simple method to explore which emotional stimuli affect cognitive performance in nonhuman primates.

Feasibility Study of Endo- and Exo-skeletal Framed Structures with Envelopes for LTA Platforms

DTIC Science & Technology

2011-02-15

pathway for design and fabrication of Endo- and Exoskeleton framed elliptical envelopes was demonstrated. Envelope sizes of 2 ft x 0.5 ft and 5 ft x...Lighter than air, Endoskeleton, Exoskeleton , Helium filled envelope, Design, Fabrication Robert Sadler and Raghu Panduranga ARIS Inc 115-C, South...Structures with Envelopes for LTA Platforms Report Title ABSTRACT A pathway for design and fabrication of Endo- and Exoskeleton framed elliptical envelopes

Mechanical design of a power-adjustable spectacle lens frame.

PubMed

Zapata, Asuncion; Barbero, Sergio

2011-05-01

Power-adjustable spectacle lenses, based on the Alvarez-Lohmann principle, can be used to provide affordable spectacles for subjective refractive errors measurement and its correction. A new mechanical frame has been designed to maximize the advantages of this technology. The design includes a mechanism to match the interpupillary distance with that of the optical centers of the lenses. The frame can be manufactured using low cost plastic injection molding techniques. A prototype has been built to test the functioning of this mechanical design.

Predicate Argument Structure Frames for Modeling Information in Operative Notes

PubMed Central

Wang, Yan; Pakhomov, Serguei; Melton, Genevieve B.

2015-01-01

The rich information about surgical procedures contained in operative notes is a valuable data source for improving the clinical evidence base and clinical research. In this study, we propose a set of Predicate Argument Structure (PAS) frames for surgical action verbs to assist in the creation of an information extraction (IE) system to automatically extract details about the techniques, equipment, and operative steps from operative notes. We created PropBank style PAS frames for the 30 top surgical action verbs based on examination of randomly selected sample sentences from 3,000 Laparoscopic Cholecystectomy notes. To assess completeness of the PAS frames to represent usage of same action verbs, we evaluated the PAS frames created on sample sentences from operative notes of 6 other gastrointestinal surgical procedures. Our results showed that the PAS frames created with one type of surgery can successfully denote the usage of the same verbs in operative notes of broader surgical categories. PMID:23920664

Transitivity performance, relational hierarchy knowledge and awareness: Results of an instructional framing manipulation

PubMed Central

Kumaran, Dharshan; Ludwig, Hans

2013-01-01

The transitive inference (TI) paradigm has been widely used to examine the role of the hippocampus in generalization. Here we consider a surprising feature of experimental findings in this task: the relatively poor transitivity performance and levels of hierarchy knowledge achieved by adult human subjects. We focused on the influence of the task instructions on participants’ subsequent performance—a single-word framing manipulation which either specified the relation between items as transitive (i.e., OLD-FRAME: choose which item is “older”) or left it ambiguous (i.e., NO-FRAME: choose which item is “correct”). We show a marked but highly specific effect of manipulating prior knowledge through instruction: transitivity performance and levels of relational hierarchy knowledge were enhanced, but premise performance unchanged. Further, we show that hierarchy recall accuracy, but not conventional awareness scores, was a significant predictor of inferential performance across the entire group of participants. The current study has four main implications: first, our findings establish the importance of the task instructions, and prior knowledge, in the TI paradigm—suggesting that they influence the size of the overall hypothesis space (e.g., to favor a linear hierarchical structure over other possibilities in the OLD-FRAME). Second, the dissociable effects of the instructional frame on premise and inference performance provide evidence for the operation of distinct underlying mechanisms (i.e., an associative mechanism vs. relational hierarchy knowledge). Third, our findings suggest that a detailed measurement of hierarchy recall accuracy may be a more sensitive index of relational hierarchy knowledge, than conventional awareness score—and should be used in future studies investigating links between awareness and inferential performance. Finally, our study motivates an experimental setting that ensures robust hierarchy learning across participants—therefore facilitating study of the neural mechanisms underlying the learning and representation of linear hierarchies. PMID:23804544

Transitivity performance, relational hierarchy knowledge and awareness: results of an instructional framing manipulation.

PubMed

Kumaran, Dharshan; Ludwig, Hans

2013-12-01

The transitive inference (TI) paradigm has been widely used to examine the role of the hippocampus in generalization. Here we consider a surprising feature of experimental findings in this task: the relatively poor transitivity performance and levels of hierarchy knowledge achieved by adult human subjects. We focused on the influence of the task instructions on participants' subsequent performance--a single-word framing manipulation which either specified the relation between items as transitive (i.e., OLD-FRAME: choose which item is "older") or left it ambiguous (i.e., NO-FRAME: choose which item is "correct"). We show a marked but highly specific effect of manipulating prior knowledge through instruction: transitivity performance and levels of relational hierarchy knowledge were enhanced, but premise performance unchanged. Further, we show that hierarchy recall accuracy, but not conventional awareness scores, was a significant predictor of inferential performance across the entire group of participants. The current study has four main implications: first, our findings establish the importance of the task instructions, and prior knowledge, in the TI paradigm--suggesting that they influence the size of the overall hypothesis space (e.g., to favor a linear hierarchical structure over other possibilities in the OLD-FRAME). Second, the dissociable effects of the instructional frame on premise and inference performance provide evidence for the operation of distinct underlying mechanisms (i.e., an associative mechanism vs. relational hierarchy knowledge). Third, our findings suggest that a detailed measurement of hierarchy recall accuracy may be a more sensitive index of relational hierarchy knowledge, than conventional awareness score--and should be used in future studies investigating links between awareness and inferential performance. Finally, our study motivates an experimental setting that ensures robust hierarchy learning across participants--therefore facilitating study of the neural mechanisms underlying the learning and representation of linear hierarchies. Copyright © 2013 The Authors. Hippocampus Published by Wiley Periodicals, Inc.

Can decision biases improve insurance outcomes? An experiment on status quo bias in health insurance choice.

PubMed

Krieger, Miriam; Felder, Stefan

2013-06-19

Rather than conforming to the assumption of perfect rationality in neoclassical economic theory, decision behavior has been shown to display a host of systematic biases. Properly understood, these patterns can be instrumentalized to improve outcomes in the public realm. We conducted a laboratory experiment to study whether decisions over health insurance policies are subject to status quo bias and, if so, whether experience mitigates this framing effect. Choices in two treatment groups with status quo defaults are compared to choices in a neutrally framed control group. A two-step design features sorting of subjects into the groups, allowing us to control for selection effects due to risk preferences. The results confirm the presence of a status quo bias in consumer choices over health insurance policies. However, this effect of the default framing does not persist as subjects repeat this decision in later periods of the experiment. Our results have implications for health care policy, for example suggesting that the use of non-binding defaults in health insurance can facilitate the spread of co-insurance policies and thereby help contain health care expenditure.

Applying Global Workspace Theory to the Frame Problem

ERIC Educational Resources Information Center

Shanahan, Murray; Baars, Bernard

2005-01-01

The subject of this article is the frame problem, as conceived by certain cognitive scientists and philosophers of mind, notably Fodor for whom it stands as a fundamental obstacle to progress in cognitive science. The challenge is to explain the capacity of so-called informationally unencapsulated cognitive processes to deal effectively with…

Conflict Management Styles Predicted by Managerial Frames of Reference.

ERIC Educational Resources Information Center

Van Epps, Pamela D.; Thompson, Bruce

The measurement integrity of M. A. Rahim's Organizational Conflict Inventory (ROCI-II) and D. M. Roussel's Managerial Frames of Mind Survey (MFMS) was investigated, as was the relationship between scores on the two measures. Subjects were 369 managers from three types of organizations: (1) higher education; (2) not-for-profit public sector…

78 FR 25905 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-03

... that the frame-to-floor beam attachment is subject to widespread fatigue damage (WFD). This proposed AD... fatigue cracking at the frame-to-floor beam attachment, on both the left- and right-sides, which could... between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information...

Mars Science Laboratory Frame Manager for Centralized Frame Tree Database and Target Pointing

NASA Technical Reports Server (NTRS)

Kim, Won S.; Leger, Chris; Peters, Stephen; Carsten, Joseph; Diaz-Calderon, Antonio

2013-01-01

The FM (Frame Manager) flight software module is responsible for maintaining the frame tree database containing coordinate transforms between frames. The frame tree is a proper tree structure of directed links, consisting of surface and rover subtrees. Actual frame transforms are updated by their owner. FM updates site and saved frames for the surface tree. As the rover drives to a new area, a new site frame with an incremented site index can be created. Several clients including ARM and RSM (Remote Sensing Mast) update their related rover frames that they own. Through the onboard centralized FM frame tree database, client modules can query transforms between any two frames. Important applications include target image pointing for RSM-mounted cameras and frame-referenced arm moves. The use of frame tree eliminates cumbersome, error-prone calculations of coordinate entries for commands and thus simplifies flight operations significantly.

Life Comparative Analysis of Energy Consumption and CO2 Emissions of Different Building Structural Frame Types

PubMed Central

Kim, Sangyong; Moon, Joon-Ho; Shin, Yoonseok; Kim, Gwang-Hee; Seo, Deok-Seok

2013-01-01

The objective of this research is to quantitatively measure and compare the environmental load and construction cost of different structural frame types. Construction cost also accounts for the costs of CO2 emissions of input materials. The choice of structural frame type is a major consideration in construction, as this element represents about 33% of total building construction costs. In this research, four constructed buildings were analyzed, with these having either reinforced concrete (RC) or steel (S) structures. An input-output framework analysis was used to measure energy consumption and CO2 emissions of input materials for each structural frame type. In addition, the CO2 emissions cost was measured using the trading price of CO2 emissions on the International Commodity Exchange. This research revealed that both energy consumption and CO2 emissions were, on average, 26% lower with the RC structure than with the S structure, and the construction costs (including the CO2 emissions cost) of the RC structure were about 9.8% lower, compared to the S structure. This research provides insights through which the construction industry will be able to respond to the carbon market, which is expected to continue to grow in the future. PMID:24227998

Fabric panel clean change-out frame

DOEpatents

Brown, Ronald M.

1995-01-31

A fabric panel clean change-out frame, for use on a containment structure having rigid walls, is formed of a compression frame and a closure panel. The frame is formed of elongated spacers, each carrying a plurality of closely spaced flat springs, and each having a hooked lip extending on the side of the spring facing the spacer. The closure panel is includes a perimeter frame formed of flexible, wedge-shaped frame members that are receivable under the springs to deflect the hooked lips. A groove on the flexible frame members engages the hooked lips and locks the frame members in place under the springs. A flexible fabric panel is connected to the flexible frame members and closes its center.

Use of reinforced inorganic cement materials for spark wire and drift chamber wire frames

NASA Technical Reports Server (NTRS)

1987-01-01

The results of a survey, materials test, and analysis study directed toward the development of an inorganic glass-fiber reinforced cement material for use in the construction of space qualified spark wire frames and drift chamber frames are presented. The purpose for this research was to evaluate the feasibility of using glass fiber reinforced cement (GFRC) for large dimensioned structural frames for supporting a number of precisely located spark wires in multiple planes. A survey of the current state of the art in fiber reinforced cement materials was made; material sample mixes were made and tested to determine their laboratory performances. Tests conducted on sample materials showed that compressive and flexural strengths of this material could approach values which would enable fabrication of structural spark wire frames.

The Controllable Ball Joint Mechanism

NASA Astrophysics Data System (ADS)

Tung, Yung Cheng; Chieng, Wei-Hua; Ho, Shrwai

A controllable ball joint mechanism with three rotational degrees of freedom is proposed in this paper. The mechanism is composed of three bevel gears, one of which rotates with respect to a fixed frame and the others rotate with respect to individual floating frames. The output is the resultant motion of the differential motions by the motors that rotates the bevel gears at the fixed frame and the floating frames. The mechanism is capable of a large rotation, and the structure is potentially compact. The necessary inverse and forward kinematic analyses as well as the derivation of kinematic singularity are provided according to the kinematical equivalent structure described in this paper.

The Acquisition of Verb Argument Structure in Basilectal Jakarta Indonesian

ERIC Educational Resources Information Center

Hidajat, Lanny

2010-01-01

This dissertation studies the acquisition of verb argument structure in the basilectal subvariety of Jakarta Indonesian (henceforth, bJI). There are two characteristics of bJI that potentially affect the acquisition of verb argument structure. First, bJI sentences can surface not only in the full frame but also in truncated frames. Second, the…

Three-Dimensional Motion Estimation Using Shading Information in Multiple Frames

DTIC Science & Technology

1989-09-01

j. Threle-D.imensionai GO Motion Estimation U sing, Shadin g Ilnformation in Multiple Frames- IJean-Pierre Schotf MIT Artifi -cial intelligence...vision 3-D structure 3-D vision- shape from shading multiple frames 20. ABSTRACT (Cofrn11,00 an reysrf* OWd Of Rssss00n7 Ad 4111111& F~ block f)nseq See...motion and shading have been treated as two disjoint problems. On the one hand, researchers studying motion or structure from motion often assume

Good things don't come easy (to mind): explaining framing effects in judgments of truth.

PubMed

Hilbig, Benjamin E

2012-01-01

Recently, the general phenomenon of a positive-negative-asymmetry was extended to judgments of truth. That is, negatively framed statements were shown to receive substantially higher truth ratings than formally equivalent statements framed positively. However, the cognitive mechanisms underlying this effect are unknown, so far. In the current work, two potential accounts are introduced and tested against each other in three experiments: On the one hand, negative framing may induce increased elaboration and thereby persuasion. Alternatively, negative framing could yield faster retrieval or generation of evidence and thus influence subjective veracity via experiential fluency. Two experiments drawing on response latencies and one manipulating the delay between information acquisition and judgment provide support for the fluency-based account. Overall, results replicate and extend the negatively-biased framing effect in truth judgments and show that processing fluency may account for it. © 2011 Hogrefe Publishing

Finite element analysis on the bending condition of truck frame before and after opening

NASA Astrophysics Data System (ADS)

Cai, Kaiwu; Cheng, Wei; Lu, Jifu

2018-05-01

Based on the design parameters of a truck frame, the structure design and model of the truck frame are built. Based on the finite element theory, the load, the type of fatigue and the material parameters of the frame are combined with the semi-trailer. Using finite element analysis software, after a truck frame hole in bending condition for the finite element analysis of comparison, through the analysis found that the truck frame hole under bending condition can meet the strength requirements are very helpful for improving the design of the truck frame.

Evaluation of Structural Robustness against Column Loss: Methodology and Application to RC Frame Buildings.

PubMed

Bao, Yihai; Main, Joseph A; Noh, Sam-Young

2017-08-01

A computational methodology is presented for evaluating structural robustness against column loss. The methodology is illustrated through application to reinforced concrete (RC) frame buildings, using a reduced-order modeling approach for three-dimensional RC framing systems that includes the floor slabs. Comparisons with high-fidelity finite-element model results are presented to verify the approach. Pushdown analyses of prototype buildings under column loss scenarios are performed using the reduced-order modeling approach, and an energy-based procedure is employed to account for the dynamic effects associated with sudden column loss. Results obtained using the energy-based approach are found to be in good agreement with results from direct dynamic analysis of sudden column loss. A metric for structural robustness is proposed, calculated by normalizing the ultimate capacities of the structural system under sudden column loss by the applicable service-level gravity loading and by evaluating the minimum value of this normalized ultimate capacity over all column removal scenarios. The procedure is applied to two prototype 10-story RC buildings, one employing intermediate moment frames (IMFs) and the other employing special moment frames (SMFs). The SMF building, with its more stringent seismic design and detailing, is found to have greater robustness.

Anti-aliasing algorithm development

NASA Astrophysics Data System (ADS)

Bodrucki, F.; Davis, J.; Becker, J.; Cordell, J.

2017-10-01

In this paper, we discuss the testing image processing algorithms for mitigation of aliasing artifacts under pulsed illumination. Previously sensors were tested, one with a fixed frame rate and one with an adjustable frame rate, which results showed different degrees of operability when subjected to a Quantum Cascade Laser (QCL) laser pulsed at the frame rate of the fixe-rate sensor. We implemented algorithms to allow the adjustable frame-rate sensor to detect the presence of aliasing artifacts, and in response, to alter the frame rate of the sensor. The result was that the sensor output showed a varying laser intensity (beat note) as opposed to a fixed signal level. A MIRAGE Infrared Scene Projector (IRSP) was used to explore the efficiency of the new algorithms, introduction secondary elements into the sensor's field of view.

Low-frequency and wideband vibration energy harvester with flexible frame and interdigital structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Pengwei, E-mail: lipengwei@tyut.edu.cn; Wang, Yanfen; Luo, Cuixian

2015-04-15

As an alternative to traditional cantilever beam structures and their evolutions, a flexible beam based, interdigital structure, vibration energy harvester has been presented and investigated. The proposed interdigital-shaped oscillator consists of a rectangular flexible frame and series of cantilever beams interdigitally bonded to it. In order to achieve low frequency and wide-bandwidth harvesting, Young’s modulus of materials, frame size and the amount of the cantilevers have been studied systematically. The measured frequency responses of the designed device (PDMS frame, quintuple piezoelectric cantilever beams) show a 460% increase in bandwidth below 80Hz. When excited at an acceleration of 1.0 g, themore » energy harvester achieves to a maximum open-circuit voltage of 65V, and the maximum output power 4.5 mW.« less

Effects of floor location on response of composite fuselage frames

NASA Technical Reports Server (NTRS)

Carden, Huey D.; Jones, Lisa E.; Fasanella, Edwin L.

1992-01-01

Experimental and analytical results are presented which show the effect of floor placement on the structural response and strength of circular fuselage frames constructed of graphite-epoxy composite material. The research was conducted to study the behavior of conventionally designed advanced composite aircraft components. To achieve desired new designs which incorporate improved energy absorption capabilities requires an understanding of how these conventional designs behave under crash type loadings. Data are presented on the static behavior of the composite structure through photographs of the frame specimen, experimental strain distributions, and through analytical data from composite structural models. An understanding of this behavior can aid the dynamist in predicting the crash behavior of these structures and may assist the designer in achieving improved designs for energy absorption and crash behavior of future structures.

Non-Destructive Inspection of Impact Damage in Composite Aircraft Panels by Ultrasonic Guided Waves and Statistical Processing.

PubMed

Capriotti, Margherita; Kim, Hyungsuk E; Scalea, Francesco Lanza di; Kim, Hyonny

2017-06-04

This paper discusses a non-destructive evaluation (NDE) technique for the detection of damage in composite aircraft structures following high energy wide area blunt impact (HEWABI) from ground service equipment (GSE), such as heavy cargo loaders and other heavy equipment. The test structures typically include skin, co-cured stringers, and C-frames that are bolt-connected onto the skin with shear ties. The inspection exploits the waveguide geometry of these structures by utilizing ultrasonic guided waves and a line scan approach. Both a contact prototype and a non-contact prototype were developed and tested on realistic test panels subjected to impact in the laboratory. The results are presented in terms of receiver operating characteristic curves that show excellent probability of detection with low false alarm rates for defects located in the panel skin and stringers.

Non-Destructive Inspection of Impact Damage in Composite Aircraft Panels by Ultrasonic Guided Waves and Statistical Processing

PubMed Central

Capriotti, Margherita; Kim, Hyungsuk E.; Lanza di Scalea, Francesco; Kim, Hyonny

2017-01-01

This paper discusses a non-destructive evaluation (NDE) technique for the detection of damage in composite aircraft structures following high energy wide area blunt impact (HEWABI) from ground service equipment (GSE), such as heavy cargo loaders and other heavy equipment. The test structures typically include skin, co-cured stringers, and C-frames that are bolt-connected onto the skin with shear ties. The inspection exploits the waveguide geometry of these structures by utilizing ultrasonic guided waves and a line scan approach. Both a contact prototype and a non-contact prototype were developed and tested on realistic test panels subjected to impact in the laboratory. The results are presented in terms of receiver operating characteristic curves that show excellent probability of detection with low false alarm rates for defects located in the panel skin and stringers. PMID:28772976

Combined non-parametric and parametric approach for identification of time-variant systems

NASA Astrophysics Data System (ADS)

Dziedziech, Kajetan; Czop, Piotr; Staszewski, Wieslaw J.; Uhl, Tadeusz

2018-03-01

Identification of systems, structures and machines with variable physical parameters is a challenging task especially when time-varying vibration modes are involved. The paper proposes a new combined, two-step - i.e. non-parametric and parametric - modelling approach in order to determine time-varying vibration modes based on input-output measurements. Single-degree-of-freedom (SDOF) vibration modes from multi-degree-of-freedom (MDOF) non-parametric system representation are extracted in the first step with the use of time-frequency wavelet-based filters. The second step involves time-varying parametric representation of extracted modes with the use of recursive linear autoregressive-moving-average with exogenous inputs (ARMAX) models. The combined approach is demonstrated using system identification analysis based on the experimental mass-varying MDOF frame-like structure subjected to random excitation. The results show that the proposed combined method correctly captures the dynamics of the analysed structure, using minimum a priori information on the model.

Model-based framework for multi-axial real-time hybrid simulation testing

NASA Astrophysics Data System (ADS)

Fermandois, Gaston A.; Spencer, Billie F.

2017-10-01

Real-time hybrid simulation is an efficient and cost-effective dynamic testing technique for performance evaluation of structural systems subjected to earthquake loading with rate-dependent behavior. A loading assembly with multiple actuators is required to impose realistic boundary conditions on physical specimens. However, such a testing system is expected to exhibit significant dynamic coupling of the actuators and suffer from time lags that are associated with the dynamics of the servo-hydraulic system, as well as control-structure interaction (CSI). One approach to reducing experimental errors considers a multi-input, multi-output (MIMO) controller design, yielding accurate reference tracking and noise rejection. In this paper, a framework for multi-axial real-time hybrid simulation (maRTHS) testing is presented. The methodology employs a real-time feedback-feedforward controller for multiple actuators commanded in Cartesian coordinates. Kinematic transformations between actuator space and Cartesian space are derived for all six-degrees-offreedom of the moving platform. Then, a frequency domain identification technique is used to develop an accurate MIMO transfer function of the system. Further, a Cartesian-domain model-based feedforward-feedback controller is implemented for time lag compensation and to increase the robustness of the reference tracking for given model uncertainty. The framework is implemented using the 1/5th-scale Load and Boundary Condition Box (LBCB) located at the University of Illinois at Urbana- Champaign. To demonstrate the efficacy of the proposed methodology, a single-story frame subjected to earthquake loading is tested. One of the columns in the frame is represented physically in the laboratory as a cantilevered steel column. For realtime execution, the numerical substructure, kinematic transformations, and controllers are implemented on a digital signal processor. Results show excellent performance of the maRTHS framework when six-degrees-of-freedom are controlled at the interface between substructures.

Clinical predictors of the optimal spectacle correction for comfort performing desktop tasks.

PubMed

Leffler, Christopher T; Davenport, Byrd; Rentz, Jodi; Miller, Amy; Benson, William

2008-11-01

The best strategy for spectacle correction of presbyopia for near tasks has not been determined. Thirty volunteers over the age of 40 years were tested for subjective accommodative amplitude, pupillary size, fusional vergence, interpupillary distance, arm length, preferred working distance, near and far visual acuity and preferred reading correction in the phoropter and trial frames. Subjects performed near tasks (reading, writing and counting change) using various spectacle correction strengths. Predictors of the correction maximising near task comfort were determined by multivariable linear regression. The mean age was 54.9 years (range 43 to 71) and 40 per cent had diabetes. Significant predictors of the most comfortable addition in univariate analyses were age (p<0.001), interpupillary distance (p=0.02), fusional vergence amplitude (p=0.02), distance visual acuity in the worse eye (p=0.01), vision at 40 cm in the worse eye with distance correction (p=0.01), duration of diabetes (p=0.01), and the preferred correction to read at 40 cm with the phoropter (p=0.002) or trial frames (p<0.001). Target distance selected wearing trial frames (in dioptres), arm length, and accommodative amplitude were not significant predictors (p>0.15). The preferred addition wearing trial frames holding a reading target at a distance selected by the patient was the only independent predictor. Excluding this variable, distance visual acuity was predictive independent of age or near vision wearing distance correction. The distance selected for task performance was predicted by vision wearing distance correction at near and at distance. Multivariable linear regression can be used to generate tables based on distance visual acuity and age or near vision wearing distance correction to determine tentative near spectacle addition. Final spectacle correction for desktop tasks can be estimated by subjective refraction with trial frames.

Light-frame wall and floor systems : analysis and performance

Treesearch

G. Sherwood; R. C. Moody

1989-01-01

This report describes methods of predicting the performance of light-frame wood structures with emphasis on floor and wall systems. Methods of predicting structural performance, fire safety, and environmental concerns including thermal, moisture, and acoustic performance are addressed in the three major sections.

Stochastic filtering for damage identification through nonlinear structural finite element model updating

NASA Astrophysics Data System (ADS)

Astroza, Rodrigo; Ebrahimian, Hamed; Conte, Joel P.

2015-03-01

This paper describes a novel framework that combines advanced mechanics-based nonlinear (hysteretic) finite element (FE) models and stochastic filtering techniques to estimate unknown time-invariant parameters of nonlinear inelastic material models used in the FE model. Using input-output data recorded during earthquake events, the proposed framework updates the nonlinear FE model of the structure. The updated FE model can be directly used for damage identification and further used for damage prognosis. To update the unknown time-invariant parameters of the FE model, two alternative stochastic filtering methods are used: the extended Kalman filter (EKF) and the unscented Kalman filter (UKF). A three-dimensional, 5-story, 2-by-1 bay reinforced concrete (RC) frame is used to verify the proposed framework. The RC frame is modeled using fiber-section displacement-based beam-column elements with distributed plasticity and is subjected to the ground motion recorded at the Sylmar station during the 1994 Northridge earthquake. The results indicate that the proposed framework accurately estimate the unknown material parameters of the nonlinear FE model. The UKF outperforms the EKF when the relative root-mean-square error of the recorded responses are compared. In addition, the results suggest that the convergence of the estimate of modeling parameters is smoother and faster when the UKF is utilized.

Equilibrium theory for braided elastic filaments

NASA Astrophysics Data System (ADS)

van der Heijden, Gert

Motivated by supercoiling of DNA and other filamentous structures, we formulate a theory for equilibria of 2-braids, i.e., structures formed by two elastic rods winding around each other in continuous contact and subject to a local interstrand interaction. Unlike in previous work no assumption is made on the shape of the contact curve. Rather, this shape is found as part of the solution. The theory is developed in terms of a moving frame of directors attached to one of the strands with one of the directors pointing to the position of the other strand. The constant-distance constraint is automatically satisfied by the introduction of what we call braid strains. The price we pay is that the potential energy involves arclength derivatives of these strains, thus giving rise to a second-order variational problem. The Euler-Lagrange equations for this problem give balance equations for the overall braid force and moment referred to the moving frame as well as differential equations that can be interpreted as effective constitutive relations encoding the effect that the second strand has on the first as the braid deforms under the action of end loads. Simple analytical cases are discussed first and used as starting solutions in parameter continuation studies to compute classes of both open and closed (linked or knotted) braid solutions.

Theory of equilibria of elastic braids with applications to DNA supercoiling

NASA Astrophysics Data System (ADS)

van der Heijden, Gert; Starostin, Eugene

2014-03-01

Motivated by supercoiling of DNA and other filamentous structures, we formulate a new theory for equilibria of 2-braids, i.e., structures formed by two elastic rods winding around each other in continuous contact and subject to a local interstrand interaction. Unlike in previous work no assumption is made on the shape of the contact curve. Rather, this shape is solved for. The theory is developed in terms of a moving frame of directors attached to one of the strands with one of the directors pointing to the position of the other strand. The constant-distance constraint is automatically satisfied by the introduction of what we call braid strains. The price we pay is that the potential energy involves arclength derivatives of these strains, thus giving rise to a second-order variational problem. The Euler-Lagrange equations for this problem give balance equations for the overall braid force and moment referred to the moving frame as well as differential equations that can be interpreted as effective constitutive relations encoding the effect that the second strand has on the first as the braid deforms under the action of end loads. Both open braid and closed braid solutions (links and knots) are computed and current applications to DNA supercoiling are discussed. Research supported by EPSRC and HFSP.

Big George to Carter Mountain 115-kV transmission line project, Park and Hot Springs Counties, Wyoming. Environmental Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-02-01

The Western Area Power Administration (Western) is proposing to rebuild, operate, and maintain a 115-kilovolt (kV) transmission line between the Big George and Carter Mountain Substations in northwest Wyoming (Park and Hot Springs Counties). This environmental assessment (EA) was prepared in compliance with the National Environmental Policy Act (NEPA) and the regulations of the Council on Environmental Quality (CEQ) and the Department of Energy (DOE). The existing Big George to Carter Mountain 69-kV transmission line was constructed in 1941 by the US Department of Interior, Bureau of Reclamation, with 1/0 copper conductor on wood-pole H-frame structures without an overhead groundmore » wire. The line should be replaced because of the deteriorated condition of the wood-pole H-frame structures. Because the line lacks an overhead ground wire, it is subject to numerous outages caused by lightning. The line will be 54 years old in 1995, which is the target date for line replacement. The normal service life of a wood-pole line is 45 years. Under the No Action Alternative, no new transmission lines would be built in the project area. The existing 69-kV transmission line would continue to operate with routine maintenance, with no provisions made for replacement.« less

Framing and visual type: Effect on future Zika vaccine uptake intent

PubMed Central

Guidry, Jeanine P.D.; Carlyle, Kellie E.; LaRose, Jessica G.; Perrin, Paul; Ryan, Mark; Messner, Marcus; Adams, Jay

2018-01-01

Introduction The Zika virus is associated with the birth defect microcephaly, and while a vaccine was not available in early- 2017, several were under development. This study’s purpose was to identify effective communication strategies to promote uptake of a new vaccine, particularly among women of reproductive age. Design and methods In order to study the effects of Zika message framing (gain vs. loss) and visual type (photo vs. infographic) on future Zika vaccine uptake intent, a 2×2 between-subjects experiment was performed via an online survey in 2017 among 339 U.S. women of reproductive age (18-49 years). Participants were exposed to one of four messages, all resembling Instagram posts: gain-framed vs. loss-framed infographic, and gain-framed vs. loss-framed photo. These messages were followed by questions about Zika vaccine uptake intent as well as intermediate psychosocial variables that could lead to intent. Results There was no interaction between framing and visual type (P=0.116), and there was no effect for framing (P=0.185) or visual type (P=0.724) on future Zika vaccine uptake intent, which is likely indicative of insufficient dosage of the intervention. However, when focusing on intermediate psychosocial constructs that are known to influence behavior and intent, gain-framed messages were more effective in increasing subjective norms (P=0.005) as related to a future Zika vaccine, as well as perceived benefits (P=0.016) and self-efficacy (P=0.032). Conclusions Gain-framed messages seem to be more effective than loss-framed messages to increase several constructs that could, in turn, affect future Zika vaccine uptake intent. This is a novel finding since, traditionally, loss-framed messages are considered more beneficial in promoting vaccine-related health behaviors. Significance for public healthThe study described in this paper is significant for the field of public health for several reasons: It takes a proactive approach in studying messaging focused on the Zika vaccine before that vaccine is available, allowing for quick implementation of its limited results. In addition, this study centers on messaging in the form of realistic images consistent with those that could be posted on Instagram, thereby focusing on a relatively new yet immensely popular communications platform that few are focusing on presently. PMID:29780762

Development of Methods of Preparing Materials for Teaching Machines: Professional Paper 29-68.

ERIC Educational Resources Information Center

Skinner, B. F.; Zook, Lola M., Ed.

In the preparation of 12-inch disc teaching machine materials for elementary college courses, a preliminary analysis of subject matter and required skills precedes sequential framing. The programer must assess the beginning level of student competence and frame questions to supply new material until the proper response stands alone. Statements for…

Oceanic Circulation. A Programmed Unit of Instruction.

ERIC Educational Resources Information Center

Marine Maritime Academy, Castine.

This booklet contains a programmed lesson on oceanic circulation. It is designed to allow students to progress through the subject at their own speed. Since it is written in linear format, it is suggested that students proceed through the program from "frame" to succeeding "frame." Instructions for students on how to use the booklet are included.…

Prognostic framing of stakeholders' subjectivities: A case of all-terrain vehicle management on state public lands

Treesearch

Stanley T. Asah; David N. Bengston; Keith Wendt; Leif DeVaney

2012-01-01

Management of all-terrain vehicle (ATV) use on Minnesota state forest lands has a contentious history and land managers are caught between ATV riders, nonmotorized recreationists, private landowners, and environmental advocates. In this paper, we demonstrate the usefulness of framing distinct perspectives about ATV management on Minnesota state public forests,...

The Shock and Vibration Digest. Volume 16, Number 1

DTIC Science & Technology

1984-01-01

investigation of the measure- ment of frequency band average loss factors of structural components for use in the statistical energy analysis method of...stiffness. Matrix methods Key Words: Finite element technique. Statistical energy analysis . Experimental techniques. Framed structures, Com- puter...programs In order to further understand the practical application of the statistical energy analysis , a two section plate-like frame structure is

Adding HDLC Framing to CCSDS Recommendations

NASA Technical Reports Server (NTRS)

Hogie, Keith; Criscuolo, Ed; Parise, Ron

2004-01-01

Current Space IP missions use High-Level Data Link Control (HDLC) framing to provide standard serial link interfaces over a space link. HDLC is the standard framing technique used by all routers over clock and data serial lines and is also the basic framing used in all Frame Relay services which are widely deployed in national and international communication networks. In late 2003 a presentation was made to CCSDS committees to initiate discussion on including HDLC in the CCSDS recommendations for space systems. This presentation will summarize the differences between variable length HDLC frames and fixed length CCSDS frames. It will also discuss where and how HDLC framing would fit into the overall CCSDS structures.

As the world turns: short-term human spatial memory in egocentric and allocentric coordinates.

PubMed

Banta Lavenex, Pamela; Lecci, Sandro; Prêtre, Vincent; Brandner, Catherine; Mazza, Christian; Pasquier, Jérôme; Lavenex, Pierre

2011-05-16

We aimed to determine whether human subjects' reliance on different sources of spatial information encoded in different frames of reference (i.e., egocentric versus allocentric) affects their performance, decision time and memory capacity in a short-term spatial memory task performed in the real world. Subjects were asked to play the Memory game (a.k.a. the Concentration game) without an opponent, in four different conditions that controlled for the subjects' reliance on egocentric and/or allocentric frames of reference for the elaboration of a spatial representation of the image locations enabling maximal efficiency. We report experimental data from young adult men and women, and describe a mathematical model to estimate human short-term spatial memory capacity. We found that short-term spatial memory capacity was greatest when an egocentric spatial frame of reference enabled subjects to encode and remember the image locations. However, when egocentric information was not reliable, short-term spatial memory capacity was greater and decision time shorter when an allocentric representation of the image locations with respect to distant objects in the surrounding environment was available, as compared to when only a spatial representation encoding the relationships between the individual images, independent of the surrounding environment, was available. Our findings thus further demonstrate that changes in viewpoint produced by the movement of images placed in front of a stationary subject is not equivalent to the movement of the subject around stationary images. We discuss possible limitations of classical neuropsychological and virtual reality experiments of spatial memory, which typically restrict the sensory information normally available to human subjects in the real world. Copyright © 2011 Elsevier B.V. All rights reserved.

Spatial and physical frames of reference in positioning a limb.

PubMed

Garrett, S R; Pagano, C; Austin, G; Turvey, M T

1998-10-01

Splints attached to the right forearm were used to rotate the forearm's physical reference frame, as defined by the eigenvectors of its inertia tensor, relative to its spatial reference frame. In two experiments, when subjects were required to orient the forearm parallel to, or at 45 degrees to, the environmental horizontal, they produced limb orientations that were systematically deflected from the forearm's longitudinal spatial axis in the direction of the forearm's physical axes. The position sense seems to be based on inertial eigenvectors rather than on joint angles or gravitational torques.

49 CFR 238.415 - Rollover strength.

Code of Federal Regulations, 2010 CFR

2010-10-01

... side frame. The allowable stress in the structural members of the occupied volumes for this condition shall be one-half yield or one-half the critical buckling stress, whichever is less. Minor localized... framing. The allowable stress in the structural members of the occupied volumes for this condition shall...

49 CFR 238.415 - Rollover strength.

Code of Federal Regulations, 2012 CFR

2012-10-01

... side frame. The allowable stress in the structural members of the occupied volumes for this condition shall be one-half yield or one-half the critical buckling stress, whichever is less. Minor localized... framing. The allowable stress in the structural members of the occupied volumes for this condition shall...

49 CFR 238.415 - Rollover strength.

Code of Federal Regulations, 2014 CFR

2014-10-01

... side frame. The allowable stress in the structural members of the occupied volumes for this condition shall be one-half yield or one-half the critical buckling stress, whichever is less. Minor localized... framing. The allowable stress in the structural members of the occupied volumes for this condition shall...

49 CFR 238.415 - Rollover strength.

Code of Federal Regulations, 2013 CFR

2013-10-01

... side frame. The allowable stress in the structural members of the occupied volumes for this condition shall be one-half yield or one-half the critical buckling stress, whichever is less. Minor localized... framing. The allowable stress in the structural members of the occupied volumes for this condition shall...

49 CFR 238.415 - Rollover strength.

Code of Federal Regulations, 2011 CFR

2011-10-01

... side frame. The allowable stress in the structural members of the occupied volumes for this condition shall be one-half yield or one-half the critical buckling stress, whichever is less. Minor localized... framing. The allowable stress in the structural members of the occupied volumes for this condition shall...

29 CFR 1926.953 - Material handling.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Material handling. (a) Unloading. Prior to unloading steel, poles, cross arms and similar material, the.... During framing operations, employees shall not work under a pole or a structure suspended by a crane, A-frame or similar equipment unless the pole or structure is adequately supported. (g) Attaching the load...

29 CFR 1926.953 - Material handling.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Material handling. (a) Unloading. Prior to unloading steel, poles, cross arms and similar material, the.... During framing operations, employees shall not work under a pole or a structure suspended by a crane, A-frame or similar equipment unless the pole or structure is adequately supported. (g) Attaching the load...

29 CFR 1926.953 - Material handling.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Material handling. (a) Unloading. Prior to unloading steel, poles, cross arms and similar material, the.... During framing operations, employees shall not work under a pole or a structure suspended by a crane, A-frame or similar equipment unless the pole or structure is adequately supported. (g) Attaching the load...

Aluminum automotive space frames

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-08-01

Design of aluminum structures is to a new topic. Aircraft makers have successfully solved difficult structural problems with a high degree of understanding and reliability. Other transportation modes such as trucks, trailers, and railcars have faced structural problems with some emphasis on high- and low-cycle fatigue of welded aluminum structures. However, the automotive market places stringent engineering demands on materials and superimposes demanding cost constraints. A project was instituted at Reynolds Metals Co. to investigate the opportunities for the cost-effective application of aluminum to automotive spaceframes. Several areas were recognized as key to the success of this application. They were:more » equivalent or superior structural stiffness of the assembly to existing steel unibody and/or steel spaceframe vehicles; effective joining of spaceframe members; equivalent or superior crashworthiness of the assembly; weight savings; flexibility; and low-cost approach aimed at effective manufacturing. To gain experience with the key aspects in a practical environment, the experience of current builders of steel tube frame chassis was explored. These chassis are typically used in low-volume vehicles requiring torsional stiffness, excellent crashworthiness, and exterior body-style flexibility. A model was developed using finite element methods that accurately predicts mass and stiffness of frames. An effective aluminum space frame was generated which was 7.5% stiffer and more than 20% lighter than the steel frame, with stresses kept below the fatigue limit for aluminum welds.« less

The visual framing of graphics when used in preventative health digital news packages: exploring the use of a narrative structure as the message infrastructure.

PubMed

Sontag, Jennah M; Barnes, Spencer R

2017-09-26

Visual framing can improve health-message effectiveness. Narrative structure provides a template needed for determining how to frame visuals to maximise message effectiveness. Participants (N = 190) were assigned to a message condition determined by segments (establisher, initial, peak), graphic (static, animated) and cancer (lung, melanoma). ANOVAs revealed that melanoma was more believable than lung cancer with static graphics at the establisher and peak; narratives were more believable with animated graphics at the peak segment; melanoma elicited greater positive attitudes; graphics in the peak influenced greatest intentions. Animated graphics visually framed to emphasise information at the establisher and peak segments suggest maximum effectiveness.

Frame prediction using recurrent convolutional encoder with residual learning

NASA Astrophysics Data System (ADS)

Yue, Boxuan; Liang, Jun

2018-05-01

The prediction for the frame of a video is difficult but in urgent need in auto-driving. Conventional methods can only predict some abstract trends of the region of interest. The boom of deep learning makes the prediction for frames possible. In this paper, we propose a novel recurrent convolutional encoder and DE convolutional decoder structure to predict frames. We introduce the residual learning in the convolution encoder structure to solve the gradient issues. The residual learning can transform the gradient back propagation to an identity mapping. It can reserve the whole gradient information and overcome the gradient issues in Recurrent Neural Networks (RNN) and Convolutional Neural Networks (CNN). Besides, compared with the branches in CNNs and the gated structures in RNNs, the residual learning can save the training time significantly. In the experiments, we use UCF101 dataset to train our networks, the predictions are compared with some state-of-the-art methods. The results show that our networks can predict frames fast and efficiently. Furthermore, our networks are used for the driving video to verify the practicability.

Measurements of Acoustic Properties of Porous and Granular Materials and Application to Vibration Control

NASA Technical Reports Server (NTRS)

Park, Junhong; Palumbo, Daniel L.

2004-01-01

For application of porous and granular materials to vibro-acoustic controls, a finite dynamic strength of the solid component (frame) is an important design factor. The primary goal of this study was to investigate structural vibration damping through this frame wave propagation for various poroelastic materials. A measurement method to investigate the vibration characteristics of the frame was proposed. The measured properties were found to follow closely the characteristics of the viscoelastic materials - the dynamic modulus increased with frequency and the degree of the frequency dependence was determined by its loss factor. The dynamic stiffness of hollow cylindrical beams containing porous and granular materials as damping treatment was measured also. The data were used to extract the damping materials characteristics using the Rayleigh-Ritz method. The results suggested that the acoustic structure interaction between the frame and the structure enhances the dissipation of the vibration energy significantly.

Self-organized architectures from assorted DNA-framed nanoparticles

NASA Astrophysics Data System (ADS)

Liu, Wenyan; Halverson, Jonathan; Tian, Ye; Tkachenko, Alexei V.; Gang, Oleg

2016-09-01

The science of self-assembly has undergone a radical shift from asking questions about why individual components self-organize into ordered structures, to manipulating the resultant order. However, the quest for far-reaching nanomanufacturing requires addressing an even more challenging question: how to form nanoparticle (NP) structures with designed architectures without explicitly prescribing particle positions. Here we report an assembly concept in which building instructions are embedded into NPs via DNA frames. The integration of NPs and DNA origami frames enables the fabrication of NPs with designed anisotropic and selective interactions. Using a pre-defined set of different DNA-framed NPs, we show it is possible to design diverse planar architectures, which include periodic structures and shaped meso-objects that spontaneously emerge on mixing of the different topological types of NP. Even objects of non-trivial shapes, such as a nanoscale model of Leonardo da Vinci's Vitruvian Man, can be self-assembled successfully.

Self-organized architectures from assorted DNA-framed nanoparticles.

PubMed

Liu, Wenyan; Halverson, Jonathan; Tian, Ye; Tkachenko, Alexei V; Gang, Oleg

2016-09-01

The science of self-assembly has undergone a radical shift from asking questions about why individual components self-organize into ordered structures, to manipulating the resultant order. However, the quest for far-reaching nanomanufacturing requires addressing an even more challenging question: how to form nanoparticle (NP) structures with designed architectures without explicitly prescribing particle positions. Here we report an assembly concept in which building instructions are embedded into NPs via DNA frames. The integration of NPs and DNA origami frames enables the fabrication of NPs with designed anisotropic and selective interactions. Using a pre-defined set of different DNA-framed NPs, we show it is possible to design diverse planar architectures, which include periodic structures and shaped meso-objects that spontaneously emerge on mixing of the different topological types of NP. Even objects of non-trivial shapes, such as a nanoscale model of Leonardo da Vinci's Vitruvian Man, can be self-assembled successfully.

Self-organized architectures from assorted DNA-framed nanoparticles

DOE PAGES

Liu, Wenyan; Halverson, Jonathan; Tian, Ye; ...

2016-06-13

The science of self-assembly has undergone a radical shift from asking questions about why individual components self-organize into ordered structures, to manipulating the resultant order. However, the quest for far-reaching nanomanufacturing requires addressing an even more challenging question: how to form nanoparticle (NP) structures with designed architectures without explicitly prescribing particle positions. Here we report an assembly concept in which building instructions are embedded into NPs via DNA frames. The integration of NPs and DNA origami frames enables the fabrication of NPs with designed anisotropic and selective interactions. Using a pre-defined set of different DNA-framed NPs, we show it ismore » possible to design diverse planar architectures, which include periodic structures and shaped meso-objects that spontaneously emerge on mixing of the different topological types of NP. Even objects of non-trivial shapes, such as a nanoscale model of Leonardo da Vinci's Vitruvian Man, can be self-assembled successfully.« less

Effects of Issue Involvement and Framing of a Responsible Drinking Message on Attitudes, Intentions, and Behavior.

PubMed

de Graaf, Anneke; van den Putte, Bas; de Bruijn, Gert-Jan

2015-08-01

To decrease the prevalence and the amount of alcohol consumption among students, health messages advocating responsible alcohol behavior can be used. However, it is unclear whether responsible drinking messages are most effective when they use a gain frame, presenting the advantages of responsible drinking, or a loss frame, presenting the disadvantages of irresponsible drinking. This study tests the effects of framing and the moderating role of involvement with the issue of responsible drinking. A three-wave, between-subjects, experimental study was conducted, in which participants (N = 90) were exposed to either a gain- or loss-framed message about responsible drinking behavior at Wave 2. At all three waves, attitudes, intentions and behavior toward responsible drinking were measured. Results showed that for participants with low issue- involvement, a gain frame led to more positive attitudes and intentions toward responsible alcohol use, whereas a loss frame did not have any effects for them. For participants with high issue involvement, a loss frame led to more positive attitudes and intentions toward responsible alcohol use, whereas a gain frame did not have an effect on attitude and only a delayed effect on intention. However, there were no effects of frame and issue involvement on adhering to the guideline of responsible alcohol use and average drinking behavior.

Colour-reproduction algorithm for transmitting variable video frames and its application to capsule endoscopy

PubMed Central

Khan, Tareq; Shrestha, Ravi; Imtiaz, Md. Shamin

2015-01-01

Presented is a new power-efficient colour generation algorithm for wireless capsule endoscopy (WCE) application. In WCE, transmitting colour image data from the human intestine through radio frequency (RF) consumes a huge amount of power. The conventional way is to transmit all R, G and B components of all frames. Using the proposed dictionary-based colour generation scheme, instead of sending all R, G and B frames, first one colour frame is sent followed by a series of grey-scale frames. At the receiver end, the colour information is extracted from the colour frame and then added to colourise the grey-scale frames. After a certain number of grey-scale frames, another colour frame is sent followed by the same number of grey-scale frames. This process is repeated until the end of the video sequence to maintain the colour similarity. As a result, over 50% of RF transmission power can be saved using the proposed scheme, which will eventually lead to a battery life extension of the capsule by 4–7 h. The reproduced colour images have been evaluated both statistically and subjectively by professional gastroenterologists. The algorithm is finally implemented using a WCE prototype and the performance is validated using an ex-vivo trial. PMID:26609405

Pilotless Frame Synchronization Using LDPC Code Constraints

NASA Technical Reports Server (NTRS)

Jones, Christopher; Vissasenor, John

2009-01-01

A method of pilotless frame synchronization has been devised for low- density parity-check (LDPC) codes. In pilotless frame synchronization , there are no pilot symbols; instead, the offset is estimated by ex ploiting selected aspects of the structure of the code. The advantag e of pilotless frame synchronization is that the bandwidth of the sig nal is reduced by an amount associated with elimination of the pilot symbols. The disadvantage is an increase in the amount of receiver data processing needed for frame synchronization.

Necessary and sufficient conditions for discrete wavelet frames in CN

NASA Astrophysics Data System (ADS)

Deepshikha; Vashisht, Lalit K.

2017-07-01

We present necessary and sufficient conditions with explicit frame bounds for a discrete wavelet system of the form {DaTk ϕ } a ∈ U(N) , k ∈IN to be a frame for the unitary space CN. It is shown that the canonical dual of a discrete wavelet frame for CN has the same structure. This is not true (well known) for canonical dual of a wavelet frame for L2(R) . Several numerical examples are given to illustrate the results.

Seismic performance evaluation of RC frame-shear wall structures using nonlinear analysis methods

NASA Astrophysics Data System (ADS)

Shi, Jialiang; Wang, Qiuwei

To further understand the seismic performance of reinforced concrete (RC) frame-shear wall structures, a 1/8 model structure is scaled from a main factory structure with seven stories and seven bays. The model with four-stories and two-bays was pseudo-dynamically tested under six earthquake actions whose peak ground accelerations (PGA) vary from 50gal to 400gal. The damage process and failure patterns were investigated. Furthermore, nonlinear dynamic analysis (NDA) and capacity spectrum method (CSM) were adopted to evaluate the seismic behavior of the model structure. The top displacement curve, story drift curve and distribution of hinges were obtained and discussed. It is shown that the model structure had the characteristics of beam-hinge failure mechanism. The two methods can be used to evaluate the seismic behavior of RC frame-shear wall structures well. What’s more, the NDA can be somewhat replaced by CSM for the seismic performance evaluation of RC structures.

Ultrasound-based quantification of vitreous floaters correlates with contrast sensitivity and quality of life.

PubMed

Mamou, Jonathan; Wa, Christianne A; Yee, Kenneth M P; Silverman, Ronald H; Ketterling, Jeffrey A; Sadun, Alfredo A; Sebag, J

2015-01-22

Clinical evaluation of floaters lacks quantitative assessment of vitreous structure. This study used quantitative ultrasound (QUS) to measure vitreous opacities. Since floaters reduce contrast sensitivity (CS) and quality of life (Visual Function Questionnaire [VFQ]), it is hypothesized that QUS will correlate with CS and VFQ in patients with floaters. Twenty-two eyes (22 subjects; age = 57 ± 19 years) with floaters were evaluated with Freiburg acuity contrast testing (FrACT; %Weber) and VFQ. Ultrasonography used a customized probe (15-MHz center frequency, 20-mm focal length, 7-mm aperture) with longitudinal and transverse scans taken in primary gaze and a horizontal longitudinal scan through premacular vitreous in temporal gaze. Each scan set had 100 frames of log-compressed envelope data. Within each frame, two regions of interest (ROIs) were analyzed (whole-central and posterior vitreous) to yield three parameters (energy, E; mean amplitude, M; and percentage of vitreous filled by echodensities, P50) averaged over the entire 100-frame dataset. Statistical analyses evaluated E, M, and P50 correlations with CS and VFQ. Contrast sensitivity ranged from 1.19%W (normal) to 5.59%W. All QUS parameters in two scan positions within the whole-central ROI correlated with CS (R > 0.67, P < 0.001). P50 in the nasal longitudinal position had R = 0.867 (P < 0.001). Correlations with VFQ ranged from R = 0.52 (P < 0.013) to R = 0.65 (P < 0.001). Quantitative ultrasound provides quantitative measures of vitreous echodensity that correlate with CS and VFQ, providing objective assessment of vitreous structure underlying the functional disturbances induced by floaters, useful to quantify vitreous disease severity and the response to therapy. Copyright 2015 The Association for Research in Vision and Ophthalmology, Inc.

Ultrasound-Based Quantification of Vitreous Floaters Correlates with Contrast Sensitivity and Quality of Life

PubMed Central

Mamou, Jonathan; Wa, Christianne A.; Yee, Kenneth M. P.; Silverman, Ronald H.; Ketterling, Jeffrey A.; Sadun, Alfredo A.; Sebag, J.

2015-01-01

Purpose. Clinical evaluation of floaters lacks quantitative assessment of vitreous structure. This study used quantitative ultrasound (QUS) to measure vitreous opacities. Since floaters reduce contrast sensitivity (CS) and quality of life (Visual Function Questionnaire [VFQ]), it is hypothesized that QUS will correlate with CS and VFQ in patients with floaters. Methods. Twenty-two eyes (22 subjects; age = 57 ± 19 years) with floaters were evaluated with Freiburg acuity contrast testing (FrACT; %Weber) and VFQ. Ultrasonography used a customized probe (15-MHz center frequency, 20-mm focal length, 7-mm aperture) with longitudinal and transverse scans taken in primary gaze and a horizontal longitudinal scan through premacular vitreous in temporal gaze. Each scan set had 100 frames of log-compressed envelope data. Within each frame, two regions of interest (ROIs) were analyzed (whole-central and posterior vitreous) to yield three parameters (energy, E; mean amplitude, M; and percentage of vitreous filled by echodensities, P50) averaged over the entire 100-frame dataset. Statistical analyses evaluated E, M, and P50 correlations with CS and VFQ. Results. Contrast sensitivity ranged from 1.19%W (normal) to 5.59%W. All QUS parameters in two scan positions within the whole-central ROI correlated with CS (R > 0.67, P < 0.001). P50 in the nasal longitudinal position had R = 0.867 (P < 0.001). Correlations with VFQ ranged from R = 0.52 (P < 0.013) to R = 0.65 (P < 0.001). Conclusions. Quantitative ultrasound provides quantitative measures of vitreous echodensity that correlate with CS and VFQ, providing objective assessment of vitreous structure underlying the functional disturbances induced by floaters, useful to quantify vitreous disease severity and the response to therapy. PMID:25613948

Fire development and wall endurance in sandwich and wood-frame structures

Treesearch

Carlton A. Holmes; Herbert W. Eickner; John J. Brenden; Curtis C. Peters; Robert H. White

1980-01-01

Large-scale fire tests were conducted on seven 16- by 24-foot structures. Four of these structures were of sandwich construction with cores of plastic or paper honeycomb and three were of wood-frame construction. The wasss were loaded to a computer design loading, and the fire endurance determined under a fire exposure from a typical building contents loading of 4-1/2...

Staying Power: The Relationship of Public School Superintendent Tenure to Leadership Frames

ERIC Educational Resources Information Center

Elliff, Doyne Scott

2012-01-01

The study examined the types of leadership frames ("human resource," "structural," "political," and "symbolic") (Bolman & Deal, 1997) most often used by public school superintendents in Texas, the relationship of leadership frames to the length of superintendent tenure in a single school district, and…

High-speed adaptive optics line scan confocal retinal imaging for human eye

PubMed Central

Wang, Xiaolin; Zhang, Yuhua

2017-01-01

Purpose Continuous and rapid eye movement causes significant intraframe distortion in adaptive optics high resolution retinal imaging. To minimize this artifact, we developed a high speed adaptive optics line scan confocal retinal imaging system. Methods A high speed line camera was employed to acquire retinal image and custom adaptive optics was developed to compensate the wave aberration of the human eye’s optics. The spatial resolution and signal to noise ratio were assessed in model eye and in living human eye. The improvement of imaging fidelity was estimated by reduction of intra-frame distortion of retinal images acquired in the living human eyes with frame rates at 30 frames/second (FPS), 100 FPS, and 200 FPS. Results The device produced retinal image with cellular level resolution at 200 FPS with a digitization of 512×512 pixels/frame in the living human eye. Cone photoreceptors in the central fovea and rod photoreceptors near the fovea were resolved in three human subjects in normal chorioretinal health. Compared with retinal images acquired at 30 FPS, the intra-frame distortion in images taken at 200 FPS was reduced by 50.9% to 79.7%. Conclusions We demonstrated the feasibility of acquiring high resolution retinal images in the living human eye at a speed that minimizes retinal motion artifact. This device may facilitate research involving subjects with nystagmus or unsteady fixation due to central vision loss. PMID:28257458

High-speed adaptive optics line scan confocal retinal imaging for human eye.

PubMed

Lu, Jing; Gu, Boyu; Wang, Xiaolin; Zhang, Yuhua

2017-01-01

Continuous and rapid eye movement causes significant intraframe distortion in adaptive optics high resolution retinal imaging. To minimize this artifact, we developed a high speed adaptive optics line scan confocal retinal imaging system. A high speed line camera was employed to acquire retinal image and custom adaptive optics was developed to compensate the wave aberration of the human eye's optics. The spatial resolution and signal to noise ratio were assessed in model eye and in living human eye. The improvement of imaging fidelity was estimated by reduction of intra-frame distortion of retinal images acquired in the living human eyes with frame rates at 30 frames/second (FPS), 100 FPS, and 200 FPS. The device produced retinal image with cellular level resolution at 200 FPS with a digitization of 512×512 pixels/frame in the living human eye. Cone photoreceptors in the central fovea and rod photoreceptors near the fovea were resolved in three human subjects in normal chorioretinal health. Compared with retinal images acquired at 30 FPS, the intra-frame distortion in images taken at 200 FPS was reduced by 50.9% to 79.7%. We demonstrated the feasibility of acquiring high resolution retinal images in the living human eye at a speed that minimizes retinal motion artifact. This device may facilitate research involving subjects with nystagmus or unsteady fixation due to central vision loss.

Re-conceptualizing stress: Shifting views on the consequences of stress and its effects on stress reactivity

PubMed Central

Liu, Jenny J. W.

2017-01-01

Background The consequences of stress are typically regarded from a deficit-oriented approach, conceptualizing stress to be entirely negative in its outcomes. This approach is unbalanced, and may further hinder individuals from engaging in adaptive coping. In the current study, we explored whether negative views and beliefs regarding stress interacted with a stress framing manipulation (positive, neutral and negative) on measures of stress reactivity for both psychosocial and physiological stressors. Method Ninety participants were randomized into one of three framing conditions that conceptualized the experience of stress in balanced, unbalanced-negative or unbalanced-positive ways. After watching a video on stress, participants underwent a psychosocial (Trier Social Stress Test), or a physiological (CO2 challenge) method of stress-induction. Subjective and objective markers of stress were assessed. Results Most of the sampled population regarded stress as negative prior to framing. Further, subjective and objective reactivity were greater to the TSST compared to the CO2 challenge. Additionally, significant cubic trends were observed in the interactions of stress framing and stress-induction methodologies on heart rate and blood pressure. Balanced framing conditions in the TSST group had a significantly larger decrease in heart rate and diastolic blood pressure following stress compared to the positive and negative framing conditions. Conclusion Findings confirmed a deficit-orientation of stress within the sampled population. In addition, results highlighted the relative efficacy of the TSST compared to CO2 as a method of stress provocation. Finally, individuals in framing conditions that posited stress outcomes in unbalanced manners responded to stressors less efficiently. This suggests that unbalanced framing of stress may have set forth unrealistic expectations regarding stress that later hindered individuals from adaptive responses to stress. Potential benefits of alternative conceptualizations of stress on stress reactivity are discussed, and suggestions for future research are made. PMID:28273132

Evaluation of Structural Robustness against Column Loss: Methodology and Application to RC Frame Buildings

PubMed Central

Bao, Yihai; Main, Joseph A.; Noh, Sam-Young

2017-01-01

A computational methodology is presented for evaluating structural robustness against column loss. The methodology is illustrated through application to reinforced concrete (RC) frame buildings, using a reduced-order modeling approach for three-dimensional RC framing systems that includes the floor slabs. Comparisons with high-fidelity finite-element model results are presented to verify the approach. Pushdown analyses of prototype buildings under column loss scenarios are performed using the reduced-order modeling approach, and an energy-based procedure is employed to account for the dynamic effects associated with sudden column loss. Results obtained using the energy-based approach are found to be in good agreement with results from direct dynamic analysis of sudden column loss. A metric for structural robustness is proposed, calculated by normalizing the ultimate capacities of the structural system under sudden column loss by the applicable service-level gravity loading and by evaluating the minimum value of this normalized ultimate capacity over all column removal scenarios. The procedure is applied to two prototype 10-story RC buildings, one employing intermediate moment frames (IMFs) and the other employing special moment frames (SMFs). The SMF building, with its more stringent seismic design and detailing, is found to have greater robustness. PMID:28890599

Can Decision Biases Improve Insurance Outcomes? An Experiment on Status Quo Bias in Health Insurance Choice

PubMed Central

Krieger, Miriam; Felder, Stefan

2013-01-01

Rather than conforming to the assumption of perfect rationality in neoclassical economic theory, decision behavior has been shown to display a host of systematic biases. Properly understood, these patterns can be instrumentalized to improve outcomes in the public realm. We conducted a laboratory experiment to study whether decisions over health insurance policies are subject to status quo bias and, if so, whether experience mitigates this framing effect. Choices in two treatment groups with status quo defaults are compared to choices in a neutrally framed control group. A two-step design features sorting of subjects into the groups, allowing us to control for selection effects due to risk preferences. The results confirm the presence of a status quo bias in consumer choices over health insurance policies. However, this effect of the default framing does not persist as subjects repeat this decision in later periods of the experiment. Our results have implications for health care policy, for example suggesting that the use of non-binding defaults in health insurance can facilitate the spread of co-insurance policies and thereby help contain health care expenditure. PMID:23783222

Towards a "Post-Public Era"? Shifting Frames in German and Australian Higher Education Policy

ERIC Educational Resources Information Center

Pick, David

2008-01-01

Higher education in Germany and Australia is being subject to pressures of market forces, internationalisation and financial constraints. This had led to both systems experiencing significant crisis and change over the past 20 years. In this paper, frame analysis is used to compare the changing policies in each nation and examine the extent to…

Integrated structural health monitoring

NASA Astrophysics Data System (ADS)

Farrar, Charles R.; Sohn, Hoon; Fugate, Michael L.; Czarnecki, Jerry J.

2001-07-01

Structural health monitoring is the implementation of a damage detection strategy for aerospace, civil and mechanical engineering infrastructure. Typical damage experienced by this infrastructure might be the development of fatigue cracks, degradation of structural connections, or bearing wear in rotating machinery. The goal of the research effort reported herein is to develop a robust and cost-effective structural health monitoring solution by integrating and extending technologies from various engineering and information technology disciplines. It is the author's opinion that all structural health monitoring systems must be application specific. Therefore, a specific application, monitoring welded moment resisting steel frame connections in structures subjected to seismic excitation, is described along with the motivation for choosing this application. The structural health monitoring solution for this application will integrate structural dynamics, wireless data acquisition, local actuation, micro-electromechanical systems (MEMS) technology, and statistical pattern recognition algorithms. The proposed system is based on an assessment of the deficiencies associated with many current structural health monitoring technologies including past efforts by the authors. This paper provides an example of the integrated approach to structural health monitoring being undertaken at Los Alamos National Laboratory and summarizes progress to date on various aspects of the technology development.

Relationship between selected orientation rest frame, circular vection and space motion sickness

NASA Technical Reports Server (NTRS)

Harm, D. L.; Parker, D. E.; Reschke, M. F.; Skinner, N. C.

1998-01-01

Space motion sickness (SMS) and spatial orientation and motion perception disturbances occur in 70-80% of astronauts. People select "rest frames" to create the subjective sense of spatial orientation. In microgravity, the astronaut's rest frame may be based on visual scene polarity cues and on the internal head and body z axis (vertical body axis). The data reported here address the following question: Can an astronaut's orientation rest frame be related and described by other variables including circular vection response latencies and space motion sickness? The astronaut's microgravity spatial orientation rest frames were determined from inflight and postflight verbal reports. Circular vection responses were elicited by rotating a virtual room continuously at 35 degrees/s in pitch, roll and yaw with respect to the astronaut. Latency to the onset of vection was recorded from the time the crew member opened their eyes to the onset of vection. The astronauts who used visual cues exhibited significantly shorter vection latencies than those who used internal z axis cues. A negative binomial regression model was used to represent the observed total SMS symptom scores for each subject for each flight day. Orientation reference type had a significant effect, resulting in an estimated three-fold increase in the expected motion sickness score on flight day 1 for astronauts who used visual cues. The results demonstrate meaningful classification of astronauts' rest frames and their relationships to sensitivity to circular vection and SMS. Thus, it may be possible to use vection latencies to predict SMS severity and duration.

Aircraft engine with inter-turbine engine frame supported counter rotating low pressure turbine rotors

NASA Technical Reports Server (NTRS)

Seda, Jorge F. (Inventor); Dunbar, Lawrence W. (Inventor); Gliebe, Philip R. (Inventor); Szucs, Peter N. (Inventor); Brauer, John C. (Inventor); Johnson, James E. (Inventor); Moniz, Thomas (Inventor); Steinmetz, Gregory T. (Inventor)

2003-01-01

An aircraft gas turbine engine assembly includes an inter-turbine frame axially located between high and low pressure turbines. Low pressure turbine has counter rotating low pressure inner and outer rotors with low pressure inner and outer shafts which are at least in part rotatably disposed co-axially within a high pressure rotor. Inter-turbine frame includes radially spaced apart radially outer first and inner second structural rings disposed co-axially about a centerline and connected by a plurality of circumferentially spaced apart struts. Forward and aft sump members having forward and aft central bores are fixedly joined to axially spaced apart forward and aft portions of the inter-turbine frame. Low pressure inner and outer rotors are rotatably supported by a second turbine frame bearing mounted in aft central bore of aft sump member. A mount for connecting the engine to an aircraft is located on first structural ring.

Studies on effects of infills in seismic resistant R/C construction

NASA Astrophysics Data System (ADS)

Brokken, S. T.; Bertero, V. V.

1981-10-01

Experimental and analytical studies of the quantitative effects of infills in the seismic performance of buildings (particularly in buildings whose structural systems are based on the use of moment resisting frames alone are summarized); and the implications of these effects regarding the design of new buildings and retrofitting of existing R/C frame structures were evaluated. The first part is concerned with the infill problem and the experimental investigation conducted to study the effects of infill panels on seismic response of reinforced concrete frames. This investigation consisted of a series of quasi-static cyclic and monotonic load tests on 1/3-scale models of the lower 3-1/2 stories of an 11 story-three bay reinforced concrete frame infilled in the outer two bays. The reinforced concrete moment frame was designed for high rotational ductility and resistance to degradation under reversed cyclic shear loads.

Leadership capabilities of physiotherapy leaders in Ireland: Part 2. Clinical specialists and advanced physiotherapy practitioners.

PubMed

McGowan, E; Elliott, N; Stokes, E

2018-05-07

Investigation of the leadership capabilities of physiotherapy managers found that they report predominantly demonstrating capabilities associated with the human resource and structural frames. However, little is known about the leadership capabilities of clinical specialists and advanced physiotherapy practitioners (APPs) who also are identified as having responsibility for leadership. To explore clinical specialists´ and APPs' perceptions of their leadership capabilities and compare them with the reported leadership capabilities of physiotherapy managers. Semi-structured interviews were conducted with a purposive sample of 17 physiotherapy clinical specialists and APPs from a range of practice settings across Ireland. The interviews were analyzed using template analysis and the coding template was based on the Bolman and Deal Leadership framework. The participants described demonstrating leadership capabilities associated with each of the four leadership frames. However, the language used by the clinical specialists/APPs suggested that they work predominantly through the human resource frame. Structural frame capabilities were reported by the clinical specialists/APPs and there were some differences to those reported by the managers. In keeping with the reported leadership capabilities of the physiotherapy managers, the employment of capabilities associated with the political frame varied between participants and symbolic frame capabilities were underused. There are many similarities in the self-reported leadership capabilities of managers and clinical specialists/APPs. However, differences were also noted. Both cohorts of physiotherapy leaders may benefit from specific development programs to develop leadership capabilities associated with the political and symbolic frames.

[The effect of goal framing on the activation of affective representations].

PubMed

Takehashi, Hiroki; Karasawa, Kaori

2007-10-01

Guided by regulatory focus theory, this study examined the effects of goal framing on the subjective experience of affect and the accessibility of affective representations. Study I examined lay persons' beliefs concerning the relationship between goal framing and certain kinds of affective experiences. The results indicated that a promotion focus was associated with happiness and disappointment, whereas a prevention focus was associated with relaxation and tension. Study 2 examined the effect of goal framing on the activation of affective representations, and found that a promotion focus activated both gain-related representations (happy and disappointment) and loss-related representations (relaxation and tension), whereas a prevention focus activated only loss-related representations. These results suggest that goal framing activates particular affective representations, and the activated affective representations may influence the interpretation of positive or negative experiences. The discussion considered the function of the activation of affective representations as a mediator between goal framing and its cognitive and behavioral consequences.

Prediction of strain values in reinforcements and concrete of a RC frame using neural networks

NASA Astrophysics Data System (ADS)

Vafaei, Mohammadreza; Alih, Sophia C.; Shad, Hossein; Falah, Ali; Halim, Nur Hajarul Falahi Abdul

2018-03-01

The level of strain in structural elements is an important indicator for the presence of damage and its intensity. Considering this fact, often structural health monitoring systems employ strain gauges to measure strains in critical elements. However, because of their sensitivity to the magnetic fields, inadequate long-term durability especially in harsh environments, difficulties in installation on existing structures, and maintenance cost, installation of strain gauges is not always possible for all structural components. Therefore, a reliable method that can accurately estimate strain values in critical structural elements is necessary for damage identification. In this study, a full-scale test was conducted on a planar RC frame to investigate the capability of neural networks for predicting the strain values. Two neural networks each of which having a single hidden layer was trained to relate the measured rotations and vertical displacements of the frame to the strain values measured at different locations of the frame. Results of trained neural networks indicated that they accurately estimated the strain values both in reinforcements and concrete. In addition, the trained neural networks were capable of predicting strains for the unseen input data set.

Masonry Infilling Effect On Seismic Vulnerability and Performance Level of High Ductility RC Frames

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghalehnovi, M.; Shahraki, H.

2008-07-08

In last years researchers preferred behavior-based design of structure to force-based one for designing and construction of the earthquake-resistance structures, this method is named performance based designing. The main goal of this method is designing of structure members for a certain performance or behavior. On the other hand in most of buildings, load bearing frames are infilled with masonry materials which leads to considerable changes in mechanical properties of frames. But usually infilling wall's effect has been ignored in nonlinear analysis of structures because of complication of the problem and lack of simple logical solution. As a result lateral stiffness,more » strength, ductility and performance of the structure will be computed with less accuracy. In this paper by use of Smooth hysteretic model for masonry infillings, some high ductile RC frames (4, 8 stories including 1, 2 and 3 spans) designed according to Iranian code are considered. They have been analyzed by nonlinear dynamic method in two states, with and without infilling. Then their performance has been determined with criteria of ATC 40 and compared with recommended performance in Iranian seismic code (standard No. 2800)« less

Tracing "Ethical Subjectivities" in Science Education: How Biology Textbooks Can Frame Ethico-Political Choices for Students

ERIC Educational Resources Information Center

Bazzul, Jesse

2015-01-01

This article describes how biology textbooks can work to discursively constitute a particular kind of "ethical subjectivity." Not only do textbooks constrain the possibilities for thought and action regarding ethical issues, they also require a certain kind of "subject" to partake in ethical exercises and questions. This study…

Framing Indoor Tanning Warning Messages to Reduce Skin Cancer Risks Among Young Women: Implications for Research and Policy.

PubMed

Mays, Darren; Tercyak, Kenneth P

2015-08-01

We investigated the impact of indoor tanning device warnings that communicate the risks associated with indoor tanning (i.e., loss framed) or the benefits of avoiding indoor tanning (i.e., gain framed). A convenience sample of non-Hispanic White women aged 18 to 30 years who tanned indoors at least once in the past year (n = 682) participated in a within-subjects experiment. Participants completed baseline measures and reported indoor tanning intentions and intentions to quit indoor tanning in response to 5 warning messages in random order. A text-only control warning was based on Food and Drug Administration-required warnings for indoor tanning devices. Experimental warnings included graphic content and were either gain or loss framed. In multivariable analyses, gain-framed warnings did not differ from the control warning on women's intentions to tan indoors, but they prompted stronger intentions to quit than the control message. Loss-framed warnings significantly reduced intentions to tan indoors and increased intentions to quit indoor tanning compared with control and gain-framed warnings. The public health impact of indoor tanning device warnings can be enhanced by incorporating graphic content and leveraging gain- and loss-framed messaging.

Multiframe video coding for improved performance over wireless channels.

PubMed

Budagavi, M; Gibson, J D

2001-01-01

We propose and evaluate a multi-frame extension to block motion compensation (BMC) coding of videoconferencing-type video signals for wireless channels. The multi-frame BMC (MF-BMC) coder makes use of the redundancy that exists across multiple frames in typical videoconferencing sequences to achieve additional compression over that obtained by using the single frame BMC (SF-BMC) approach, such as in the base-level H.263 codec. The MF-BMC approach also has an inherent ability of overcoming some transmission errors and is thus more robust when compared to the SF-BMC approach. We model the error propagation process in MF-BMC coding as a multiple Markov chain and use Markov chain analysis to infer that the use of multiple frames in motion compensation increases robustness. The Markov chain analysis is also used to devise a simple scheme which randomizes the selection of the frame (amongst the multiple previous frames) used in BMC to achieve additional robustness. The MF-BMC coders proposed are a multi-frame extension of the base level H.263 coder and are found to be more robust than the base level H.263 coder when subjected to simulated errors commonly encountered on wireless channels.

Confidence in the safety of blood for transfusion: the effect of message framing.

PubMed

Farrell, K; Ferguson, E; James, V; Lowe, K C

2001-11-01

Blood transfusion is a universally used, life-saving medical intervention. However, there are increasing concerns among patients about blood safety. This study investigates the effect of message framing, a means of presenting information, on confidence in blood transfusion safety. The same factual information regarding the safety of blood for transfusion was presented to a sample of 254 adult students (donors and nondonors) as either a gain frame (lives saved), a loss frame (lives lost), or a combined frame (a loss frame expressed in a positive context). This provided a basic two-way, between-subjects design with 1) blood donation history (donors vs. nondonors) and 2) message frame (gain, loss, and combined) functioning as the between-groups factors. It was hypothesized that participants would consider blood safer if information was presented as a gain frame. The role of stress appraisals as potential mediators of the framing effect was also explored. As predicted, participants receiving the gain-frame information were significantly more confident of the safety of blood for transfusion than those receiving loss-frame information or both. This was unaffected by donation history or appraisals of stress associated with transfusion. The extent to which blood was considered safe was negatively associated, independently of framing effects, with perceptions that transfusion was threatening. Information about transfusion should be conveyed to patients in a form focusing on the positive, rather than the negative, known facts about the safety of blood.

Message framing and color combination in the perception of medical information.

PubMed

Chien, Yu-Hung

2011-04-01

A 2 x 2 between-subjects design was used to examine the effects of message framing (gain vs loss) and color combination (red background with white characters vs white background with black characters) on 120 university students' perception of materials promoting the H1N1 flu vaccine and their willingness to receive the vaccine after they had read the materials. Each participant completed a 6-item questionnaire, and the results of an analysis of variance showed that participants rated vaccine information presented through loss-framed messages as having greater interest and leading to greater understanding. Loss-framed messages presented on a white background with black characters significantly increased the willingness of the participants to receive the vaccine.

Construction Cluster Volume I [Wood Structural Framing].

ERIC Educational Resources Information Center

Pennsylvania State Dept. of Justice, Harrisburg. Bureau of Correction.

The document is the first of a series, to be integrated with a G.E.D. program, containing instructional materials at the basic skills level for the construction cluster. It focuses on wood structural framing and contains 20 units: (1) occupational information; (2) blueprint reading; (3) using leveling instruments and laying out building lines; (4)…

Study on comparison of special moment frame steel structure (SMF) and base isolation special moment frame steel structure (BI-SMF) in Indonesia

NASA Astrophysics Data System (ADS)

Setiawan, Jody; Nakazawa, Shoji

2017-10-01

This paper discusses about comparison of seismic response behaviors, seismic performance and seismic loss function of a conventional special moment frame steel structure (SMF) and a special moment frame steel structure with base isolation (BI-SMF). The validation of the proposed simplified estimation method of the maximum deformation of the base isolation system by using the equivalent linearization method and the validation of the design shear force of the superstructure are investigated from results of the nonlinear dynamic response analysis. In recent years, the constructions of steel office buildings with seismic isolation system are proceeding even in Indonesia where the risk of earthquakes is high. Although the design code for the seismic isolation structure has been proposed, there is no actual construction example for special moment frame steel structure with base isolation. Therefore, in this research, the SMF and BI-SMF buildings are designed by Indonesian Building Code which are assumed to be built at Padang City in Indonesia. The material of base isolation system is high damping rubber bearing. Dynamic eigenvalue analysis and nonlinear dynamic response analysis are carried out to show the dynamic characteristics and seismic performance. In addition, the seismic loss function is obtained from damage state probability and repair cost. For the response analysis, simulated ground accelerations, which have the phases of recorded seismic waves (El Centro NS, El Centro EW, Kobe NS and Kobe EW), adapted to the response spectrum prescribed by the Indonesian design code, that has, are used.

Vibration suppression and slewing control of a flexible structure

NASA Technical Reports Server (NTRS)

Inman, Daniel J.; Garcia, Ephrahim; Pokines, Brett

1991-01-01

Examined here are the effects of motor dynamics and secondary piezoceramic actuators on vibration suppression during the slewing of flexible structures. The approach focuses on the interaction between the structure, the actuators, and the choice of control law. The results presented here are all simulated, but are based on experimentally determined parameters for the motor, structure, piezoceramic actuators, and piezofilm sensors. The simulation results clearly illustrate that the choice of motor inertia relative to beam inertia makes a critical difference in the performance of the system. In addition, the use of secondary piezoelectric actuators reduces the load requirements on the motor and also reduces the overshoot of the tip deflection. The structures considered here are a beam and a frame. The majority of results are based on a Euler Bernoulli beam model. The slewing frame introduces substantial torsional modes and a more realistic model. The slewing frame results are incomplete and represent work in progress.

Steps towards Smarter Solutions in Optometry and Ophthalmology-Inter-Device Agreement of Subjective Methods to Assess the Refractive Errors of the Eye.

PubMed

Ohlendorf, Arne; Leube, Alexander; Wahl, Siegfried

2016-07-13

To investigate the inter-device agreement and mean differences between a newly developed digital phoropter and the two standard methods (trial frame and manual phoropter). Refractive errors of two groups of participants were measured by two examiners (examiner 1 (E1): 36 subjects; examiner 2 (E2): 38 subjects). Refractive errors were assessed using a trial frame, a manual phoropter and a digital phoropter. Inter-device agreement regarding the measurement of refractive errors was analyzed for differences in terms of the power vector components (spherical equivalent (SE) and the cylindrical power vector components J0 and J45) between the used methods. Intraclass correlation coefficients (ICC's) were calculated to evaluate correlations between the used methods. Analyzing the variances between the three methods for SE, J0 and J45 using a two-way ANOVA showed no significant differences between the methods (SE: p = 0.13, J0: p = 0.58 and J45: p = 0.96) for examiner 1 and for examiner 2 (SE: p = 0.88, J0: p = 0.95 and J45: p = 1). Mean differences and ±95% Limits of Agreement for each pair of inter-device agreement regarding the SE for both examiners were as follows: Trial frame vs. digital phoropter: +0.10 D ± 0.56 D (E1) and +0.19 D ± 0.60 D (E2), manual phoropter vs. trial frame: -0.04 D ± 0.59 D (E1) and -0.12 D ± 0.49 D (E2) and for manual vs. digital phoropter: +0.06 D ± 0.65 D (E1) and +0.08 D ± 0.45 D (E2). ICCs revealed high correlations between all methods for both examiner (p < 0.001). The time to assess the subjective refraction was significantly smaller with the digital phoropter (examiner 1: p < 0.001; examiner 2: p < 0.001). "All used subjective methods show a good agreement between each other terms of ICC (>0.9). Assessing refractive errors using different subjective methods, results in similar mean differences and 95% limits of agreement, when compared to those reported in studies comparing subjective refraction non-cylcoplegic retinoscopy or autorefraction".

Steps towards Smarter Solutions in Optometry and Ophthalmology—Inter-Device Agreement of Subjective Methods to Assess the Refractive Errors of the Eye

PubMed Central

Ohlendorf, Arne; Leube, Alexander; Wahl, Siegfried

2016-01-01

Purpose: To investigate the inter-device agreement and mean differences between a newly developed digital phoropter and the two standard methods (trial frame and manual phoropter). Methods: Refractive errors of two groups of participants were measured by two examiners (examiner 1 (E1): 36 subjects; examiner 2 (E2): 38 subjects). Refractive errors were assessed using a trial frame, a manual phoropter and a digital phoropter. Inter-device agreement regarding the measurement of refractive errors was analyzed for differences in terms of the power vector components (spherical equivalent (SE) and the cylindrical power vector components J0 and J45) between the used methods. Intraclass correlation coefficients (ICC’s) were calculated to evaluate correlations between the used methods. Results: Analyzing the variances between the three methods for SE, J0 and J45 using a two-way ANOVA showed no significant differences between the methods (SE: p = 0.13, J0: p = 0.58 and J45: p = 0.96) for examiner 1 and for examiner 2 (SE: p = 0.88, J0: p = 0.95 and J45: p = 1). Mean differences and ±95% Limits of Agreement for each pair of inter-device agreement regarding the SE for both examiners were as follows: Trial frame vs. digital phoropter: +0.10 D ± 0.56 D (E1) and +0.19 D ± 0.60 D (E2), manual phoropter vs. trial frame: −0.04 D ± 0.59 D (E1) and −0.12 D ± 0.49 D (E2) and for manual vs. digital phoropter: +0.06 D ± 0.65 D (E1) and +0.08 D ± 0.45 D (E2). ICCs revealed high correlations between all methods for both examiner (p < 0.001). The time to assess the subjective refraction was significantly smaller with the digital phoropter (examiner 1: p < 0.001; examiner 2: p < 0.001). Conclusion: “All used subjective methods show a good agreement between each other terms of ICC (>0.9). Assessing refractive errors using different subjective methods, results in similar mean differences and 95% limits of agreement, when compared to those reported in studies comparing subjective refraction non-cylcoplegic retinoscopy or autorefraction”. PMID:27417629

Tensioning device for a stretched membrane collector

DOEpatents

Murphy, Lawrence M.

1984-01-01

Disclosed is a solar concentrating collector comprising an elastic membrane member for concentrating sunlight, a frame for holding the membrane member in plane and in tension, and a tensioning means for varying the tension of the membrane member. The tensioning means is disposed at the frame and is adapted to releasably attach the membrane member thereto. The tensioning means is also adapted to uniformly and symmetrically subject the membrane member to stretching forces such that membrane stresses produced thereby are distributed uniformly over a thickness of the membrane member and reciprocal twisting moments are substantially prevented from acting about said frame.

Tensioning device for a stretched membrane collector

DOEpatents

Murphy, L.M.

1984-01-01

Disclosed is a solar concentrating collector comprising an elestic membrane member for concentrating sunlight, a frame for holding the membrane member in plane and in tension, and a tensioning means for varying the tension of the membrane member. The tensioning means is disposed at the frame and is adapted to releasably attach the membrane member thereto. The tensioning means is also adapted to uniformly and symmetrically subject the membrane member to stretching forces such that membrane stresses produced thereby are distributed uniformly over a thickness of the membrane member and reciprocal twisting moments are substantially prevented from acting about said frame.

Real-time motion analytics during brain MRI improve data quality and reduce costs.

PubMed

Dosenbach, Nico U F; Koller, Jonathan M; Earl, Eric A; Miranda-Dominguez, Oscar; Klein, Rachel L; Van, Andrew N; Snyder, Abraham Z; Nagel, Bonnie J; Nigg, Joel T; Nguyen, Annie L; Wesevich, Victoria; Greene, Deanna J; Fair, Damien A

2017-11-01

Head motion systematically distorts clinical and research MRI data. Motion artifacts have biased findings from many structural and functional brain MRI studies. An effective way to remove motion artifacts is to exclude MRI data frames affected by head motion. However, such post-hoc frame censoring can lead to data loss rates of 50% or more in our pediatric patient cohorts. Hence, many scanner operators collect additional 'buffer data', an expensive practice that, by itself, does not guarantee sufficient high-quality MRI data for a given participant. Therefore, we developed an easy-to-setup, easy-to-use Framewise Integrated Real-time MRI Monitoring (FIRMM) software suite that provides scanner operators with head motion analytics in real-time, allowing them to scan each subject until the desired amount of low-movement data has been collected. Our analyses show that using FIRMM to identify the ideal scan time for each person can reduce total brain MRI scan times and associated costs by 50% or more. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Organizing knowledge for tutoring fire loss prevention

NASA Astrophysics Data System (ADS)

Schmoldt, Daniel L.

1989-09-01

The San Bernardino National Forest in southern California has recently developed a systematic approach to wildfire prevention planning. However, a comprehensive document or other mechanism for teaching this process to other prevention personnel does not exist. An intelligent tutorial expert system is being constructed to provide a means for learning the process and to assist in the creation of specific prevention plans. An intelligent tutoring system (ITS) contains two types of knowledge—domain and tutoring. The domain knowledge for wildfire prevention is structured around several foci: (1) individual concepts used in prevention planning; (2) explicitly specified interrelationships between concepts; (3) deductive methods that contain subjective judgment normally unavailable to less-experienced users; (4) analytical models of fire behavior used for identification of hazard areas; (5) how-to guidance needed for performance of planning tasks; and (6) expository information that provides a rationale for planning steps and ideas. Combining analytical, procedure, inferential, conceptual, and expositional knowledge into a tutoring environment provides the student and/or user with a multiple perspective of the subject matter. A concept network provides a unifying framework for structuring and utilizing these diverse forms of prevention planning knowledge. This network structure borrows from and combines semantic networks and frame-based knowledge representations. The flexibility of this organization facilitates an effective synthesis and organization of multiple knowledge forms.

Vision-based stress estimation model for steel frame structures with rigid links

NASA Astrophysics Data System (ADS)

Park, Hyo Seon; Park, Jun Su; Oh, Byung Kwan

2017-07-01

This paper presents a stress estimation model for the safety evaluation of steel frame structures with rigid links using a vision-based monitoring system. In this model, the deformed shape of a structure under external loads is estimated via displacements measured by a motion capture system (MCS), which is a non-contact displacement measurement device. During the estimation of the deformed shape, the effective lengths of the rigid link ranges in the frame structure are identified. The radius of the curvature of the structural member to be monitored is calculated using the estimated deformed shape and is employed to estimate stress. Using MCS in the presented model, the safety of a structure can be assessed gauge-freely. In addition, because the stress is directly extracted from the radius of the curvature obtained from the measured deformed shape, information on the loadings and boundary conditions of the structure are not required. Furthermore, the model, which includes the identification of the effective lengths of the rigid links, can consider the influences of the stiffness of the connection and support on the deformation in the stress estimation. To verify the applicability of the presented model, static loading tests for a steel frame specimen were conducted. By comparing the stress estimated by the model with the measured stress, the validity of the model was confirmed.

Experimental validation of finite element model analysis of a steel frame in simulated post-earthquake fire environments

NASA Astrophysics Data System (ADS)

Huang, Ying; Bevans, W. J.; Xiao, Hai; Zhou, Zhi; Chen, Genda

2012-04-01

During or after an earthquake event, building system often experiences large strains due to shaking effects as observed during recent earthquakes, causing permanent inelastic deformation. In addition to the inelastic deformation induced by the earthquake effect, the post-earthquake fires associated with short fuse of electrical systems and leakage of gas devices can further strain the already damaged structures during the earthquakes, potentially leading to a progressive collapse of buildings. Under these harsh environments, measurements on the involved building by various sensors could only provide limited structural health information. Finite element model analysis, on the other hand, if validated by predesigned experiments, can provide detail structural behavior information of the entire structures. In this paper, a temperature dependent nonlinear 3-D finite element model (FEM) of a one-story steel frame is set up by ABAQUS based on the cited material property of steel from EN 1993-1.2 and AISC manuals. The FEM is validated by testing the modeled steel frame in simulated post-earthquake environments. Comparisons between the FEM analysis and the experimental results show that the FEM predicts the structural behavior of the steel frame in post-earthquake fire conditions reasonably. With experimental validations, the FEM analysis of critical structures could be continuously predicted for structures in these harsh environments for a better assistant to fire fighters in their rescue efforts and save fire victims.

A Possible Approach to Inclusion of Space and Time in Frame Fields of Quantum Representations of Real and Complex Numbers

DOE PAGES

Benioff, Paul

2009-01-01

Tmore » his work is based on the field of reference frames based on quantum representations of real and complex numbers described in other work. Here frame domains are expanded to include space and time lattices. Strings of qukits are described as hybrid systems as they are both mathematical and physical systems. As mathematical systems they represent numbers. As physical systems in each frame the strings have a discrete Schrodinger dynamics on the lattices. he frame field has an iterative structure such that the contents of a stage j frame have images in a stage j - 1 (parent) frame. A discussion of parent frame images includes the proposal that points of stage j frame lattices have images as hybrid systems in parent frames. he resulting association of energy with images of lattice point locations, as hybrid systems states, is discussed. Representations and images of other physical systems in the different frames are also described.« less

Tracing "Ethical Subjectivities" in Science Education: How Biology Textbooks Can Frame Ethico-Political Choices for Students

NASA Astrophysics Data System (ADS)

Bazzul, Jesse

2015-02-01

This article describes how biology textbooks can work to discursively constitute a particular kind of "ethical subjectivity." Not only do textbooks constrain the possibilities for thought and action regarding ethical issues, they also require a certain kind of "subject" to partake in ethical exercises and questions. This study looks at how ethical questions/exercises found in four Ontario textbooks require students and teachers to think and act along specific lines. These include making ethical decisions within a legal-juridical frame; deciding what kinds of research should be publically funded; optimizing personal and population health; and regulation through policy and legislation. While engaging ethical issues in these ways is useful, educators should also question the kinds of (ethical) subjectivities that are partially constituted by discourses of science education. If science education is going to address twenty-first century problems such as climate change and social inequality, educators need to address how the possibilities for ethical engagement afforded to students work to constitute specific kinds of "ethical actors."

A dynamic load estimation method for nonlinear structures with unscented Kalman filter

NASA Astrophysics Data System (ADS)

Guo, L. N.; Ding, Y.; Wang, Z.; Xu, G. S.; Wu, B.

2018-02-01

A force estimation method is proposed for hysteretic nonlinear structures. The equation of motion for the nonlinear structure is represented in state space and the state variable is augmented by the unknown the time history of external force. Unscented Kalman filter (UKF) is improved for the force identification in state space considering the ill-condition characteristic in the computation of square roots for the covariance matrix. The proposed method is firstly validated by a numerical simulation study of a 3-storey nonlinear hysteretic frame excited by periodic force. Each storey is supposed to follow a nonlinear hysteretic model. The external force is identified and the measurement noise is considered in this case. Then a case of a seismically isolated building subjected to earthquake excitation and impact force is studied. The isolation layer performs nonlinearly during the earthquake excitation. Impact force between the seismically isolated structure and the retaining wall is estimated with the proposed method. Uncertainties such as measurement noise, model error in storey stiffness and unexpected environmental disturbances are considered. A real-time substructure testing of an isolated structure is conducted to verify the proposed method. In the experimental study, the linear main structure is taken as numerical substructure while the one of the isolations with additional mass is taken as the nonlinear physical substructure. The force applied by the actuator on the physical substructure is identified and compared with the measured value from the force transducer. The method proposed in this paper is also validated by shaking table test of a seismically isolated steel frame. The acceleration of the ground motion as the unknowns is identified by the proposed method. Results from both numerical simulation and experimental studies indicate that the UKF based force identification method can be used to identify external excitations effectively for the nonlinear structure with accurate results even with measurement noise, model error and environmental disturbances.

The Framing of Women and Health Disparities: A Critical Look at Race, Gender, and Class from the Perspectives of Grassroots Health Communicators.

PubMed

Vardeman-Winter, Jennifer

2017-05-01

As women's health has received significant political and media attention recently, I proposed an expanded structural theory of women's communication about health. Women's health communication and critical race and systemic racism research framed this study. I interviewed 15 communicators and community health workers from grass-roots organizations focused on women's health to learn of their challenges of communicating with women from communities experiencing health disparities. Findings suggest that communicators face difficulties in developing meaningful messaging for publics because of disjunctures between medical and community frames, issues in searching for health among women's many priorities, Whiteness discourses imposed on publics' experiences, and practices of correcting for power differentials. A structural theory of women's health communication, then, consists of tenets around geographic, research/funding, academic/industry, and social hierarchies. Six frames suggesting racial biases about women and health disparities are also defined. This study also includes practical solutions in education, publishing, and policy change for addressing structural challenges.

Earthquake behavior of steel cushion-implemented reinforced concrete frames

NASA Astrophysics Data System (ADS)

Özkaynak, Hasan

2018-04-01

The earthquake performance of vulnerable structures can be increased by the implementation of supplementary energy-dissipative metallic elements. The main aim of this paper is to describe the earthquake behavior of steel cushion-implemented reinforced concrete frames (SCI-RCFR) in terms of displacement demands and energy components. Several quasi-static experiments were performed on steel cushions (SC) installed in reinforced concrete (RC) frames. The test results served as the basis of the analytical models of SCs and a bare reinforced concrete frame (B-RCFR). These models were integrated in order to obtain the resulting analytical model of the SCI-RCFR. Nonlinear-time history analyses (NTHA) were performed on the SCI-RCFR under the effects of the selected earthquake data set. According to the NTHA, SC application is an effective technique for increasing the seismic performance of RC structures. The main portion of the earthquake input energy was dissipated through SCs. SCs succeeded in decreasing the plastic energy demand on structural elements by almost 50% at distinct drift levels.

Evaluation of Force Transfer Around Openings - Experimental and Analytical Studies

Treesearch

Borjen Yeh; Tom Skaggs; Frank Lam; Minghao Li; Douglas Rammer; James Wacker

2011-01-01

Wood structural panel (WSP) sheathed shear walls and diaphragms are the primary lateral-load-resistingelements in wood-frame construction. The historical performance of light-frame structures in North America is very good due, in part, to model building codes that are designed to safeguard life safety. These model building codes have spawned continual improvement and...

Asynchronous Communication: Investigating the Influences of Relational Elements and Background on the Framing Structure of Emails

ERIC Educational Resources Information Center

AlAfnan, Mohammad Awad

2015-01-01

This study explored the influences of relational elements and the background of communicators on the framing structure of email messages that were exchanged in an educational Institute in Malaysia. The investigation revealed that social distance played a more significant role than power relations as Malaysian respondents are, generally, more…

Stimulus Set Meaningfulness and Neurophysiological Differentiation: A Functional Magnetic Resonance Imaging Study

PubMed Central

Boly, Melanie; Sasai, Shuntaro; Gosseries, Olivia; Oizumi, Masafumi; Casali, Adenauer; Massimini, Marcello; Tononi, Giulio

2015-01-01

A meaningful set of stimuli, such as a sequence of frames from a movie, triggers a set of different experiences. By contrast, a meaningless set of stimuli, such as a sequence of ‘TV noise’ frames, triggers always the same experience—of seeing ‘TV noise’—even though the stimuli themselves are as different from each other as the movie frames. We reasoned that the differentiation of cortical responses underlying the subject’s experiences, as measured by Lempel-Ziv complexity (incompressibility) of functional MRI images, should reflect the overall meaningfulness of a set of stimuli for the subject, rather than differences among the stimuli. We tested this hypothesis by quantifying the differentiation of brain activity patterns in response to a movie sequence, to the same movie scrambled in time, and to ‘TV noise’, where the pixels from each movie frame were scrambled in space. While overall cortical activation was strong and widespread in all conditions, the differentiation (Lempel-Ziv complexity) of brain activation patterns was correlated with the meaningfulness of the stimulus set, being highest in the movie condition, intermediate in the scrambled movie condition, and minimal for ‘TV noise’. Stimulus set meaningfulness was also associated with higher information integration among cortical regions. These results suggest that the differentiation of neural responses can be used to assess the meaningfulness of a given set of stimuli for a given subject, without the need to identify the features and categories that are relevant to the subject, nor the precise location of selective neural responses. PMID:25970444

Compressive Loading and Modeling of Stitched Composite Stiffeners

NASA Technical Reports Server (NTRS)

Leone, Frank A., Jr.; Jegley, Dawn C.; Linton, Kim A.

2016-01-01

A series of single-frame and single-stringer compression tests were conducted at NASA Langley Research Center on specimens harvested from a large panel built using the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. Different frame and stringer designs were used in fabrication of the PRSEUS panel. In this paper, the details of the experimental testing of single-frame and single-stringer compression specimens are presented, as well as discussions on the performance of the various structural configurations included in the panel. Nonlinear finite element models were developed to further understand the failure processes observed during the experimental campaign.

Integrated optimization of nonlinear R/C frames with reliability constraints

NASA Technical Reports Server (NTRS)

Soeiro, Alfredo; Hoit, Marc

1989-01-01

A structural optimization algorithm was researched including global displacements as decision variables. The algorithm was applied to planar reinforced concrete frames with nonlinear material behavior submitted to static loading. The flexural performance of the elements was evaluated as a function of the actual stress-strain diagrams of the materials. Formation of rotational hinges with strain hardening were allowed and the equilibrium constraints were updated accordingly. The adequacy of the frames was guaranteed by imposing as constraints required reliability indices for the members, maximum global displacements for the structure and a maximum system probability of failure.

Reduction of Effective Acceleration to Microgravity Levels

NASA Technical Reports Server (NTRS)

Downey, James P.

2000-01-01

Acceleration due to earth's gravity causes buoyancy driven convection and sedimentation in solutions. In addition. pressure gradients occur as a function of the height within a liquid column. Hence gravity effects both equilbria conditions and phase transitions as a result of hydrostatic pressure gradients. The affect of gravity on the rate of heat and man transfer in solutal processes can be particularly important in polymer processing due to the high sensitivity of polymeric materials to processing conditions. The term microgravity has been coined to describe an environment in which the affects of gravitational acceleration am greatly reduced. It may seem odd to talk in term of reducing the effects of gravitational acceleration since gravitational attraction is a basic property of matter. However, die presence of gravity on in situ processing or measurements can be negated by achieving conditions in which the laboratory, or more specifically the container of the experimental materials, a subjected to the same acceleration as the materials themselves. With regard to the laboratory reference frame, there is virtually no force on the experimental solutions. This is difficult to achieve but can be done. A short review of Newtonian physics provides an explanation on both how processes we affected by gravity and how microgravity conditions are achieved. The fact that fluids deform when subject to a force bid solids do not indicates that solids have a structure able to exert an opposing force that negates an externally applied force. Liquids deform when a force is applied, indicating that a liquid structure cannot completely negate an applied force. Just how easily a liquid resists deformation is related to its viscosity. Spaceflight provides an environment in which the laboratory reference frame i.e. the spacecraft and all the equipment therein an experiencing virtually identical forces. There is no solid foundation underneath such a laboratory, so the laboratory accelerates according to the force of gravity as do the experimental fluids within the lab. Hence, the magnitude of the form excited by the laboratory on the experimental solutions within are greatly reduced. When compared with a laboratory on the ground and averaged over time, the fluids in a spaceflight laboratory experience approximately a 10 (sup -6)decrease in acceleration relative to their laboratory reference frame hence the term microgravity.

Different strategies for spatial updating in yaw and pitch path integration

PubMed Central

Goeke, Caspar M.; König, Peter; Gramann, Klaus

2013-01-01

Research in spatial navigation revealed the existence of discrete strategies defined by the use of distinct reference frames during virtual path integration. The present study investigated the distribution of these navigation strategies as a function of gender, video gaming experience, and self-estimates of spatial navigation abilities in a population of 300 subjects. Participants watched videos of virtual passages through a star-field with one turn in either the horizontal (yaw) or the vertical (pitch) axis. At the end of a passage they selected one out of four homing arrows to indicate the initial starting location. To solve the task, participants could employ two discrete strategies, navigating within either an egocentric or an allocentric reference frame. The majority of valid subjects (232/260) consistently used the same strategy in more than 75% of all trials. With that approach 33.1% of all participants were classified as Turners (using an egocentric reference frame on both axes) and 46.5% as Non-turners (using an allocentric reference frame on both axes). 9.2% of all participants consistently used an egocentric reference frame in the yaw plane but an allocentric reference frame in the pitch plane (Switcher). Investigating the influence of gender on navigation strategies revealed that females predominantly used the Non-turner strategy while males used both the Turner and the Non-turner strategy with comparable probabilities. Other than expected, video gaming experience did not influence strategy use. Based on a strong quantitative basis with the sample size about an order of magnitude larger than in typical psychophysical studies these results demonstrate that most people reliably use one out of three possible navigation strategies (Turners, Non-turners, Switchers) for spatial updating and provides a sound estimate of how those strategies are distributed within the general population. PMID:23412683

Accelerating Exploitation of Low-grade Intelligence through Semantic Text Processing of Social Media

DTIC Science & Technology

2013-06-01

importance as an information source. The brevity of social media content (e.g., 140 characters per tweet) combined with the increasing usage of mobile...platform imports unstructured text from a variety of sources and then maps the text to an existing ontology of frames (FrameNet, https...framenet.icsi.berkeley.edu/fndrupal/) during a process of Semantic Role Labeling ( SRL ). FrameNet is a structured language model grounded in the theory of Frame

Behaviour of Strengthened RC Frames with Eccentric Steel Braced Frames

NASA Astrophysics Data System (ADS)

Kamanli, Mehmet; Unal, Alptug

2017-10-01

After devastating earthquakes in recent years, strengthening of reinforced concrete buildings became an important research topic. Reinforced concrete buildings can be strengthened by steel braced frames. These steel braced frames may be made of concentrically or eccentrically indicated in Turkish Earthquake Code 2007. In this study pushover analysis of the 1/3 scaled 1 reinforced concrete frame and 1/3 scaled 4 strengthened reinforced concrete frames with internal eccentric steel braced frames were conducted by SAP2000 program. According to the results of the analyses conducted, load-displacement curves of the specimens were compared and evaluated. Adding eccentric steel braces to the bare frame decreased the story drift, and significantly increased strength, stiffness and energy dissipation capacity. In this strengthening method lateral load carrying capacity, stiffness and dissipated energy of the structure can be increased.

How does media coverage effect the consumption of antidepressants? A study of the media coverage of antidepressants in Danish online newspapers 2010-2011.

PubMed

Green Lauridsen, Michael; Kälvemark Sporrong, Sofia

2018-07-01

The news media has become a major source of health information for the public, and hence vital in the individuals' opinions and decisions about health topics. The first decrease in the usage of antidepressants in Denmark in over a decade happened alongside an intensive period of media coverage about antidepressants. The aim of this study was to examine the Danish media's coverage of antidepressants during 2010-2011 in order to explore what influence it could have had on the change in the use of antidepressants. Three media theoretical concepts, agenda-setting, priming and framing, were used to explain the media influence with regard to which subject the public should think about, which criteria the public should judge the subject by, and how the public should think about the subject. All articles about antidepressants in the main Danish Internet newspapers from 2010-2011 were analyzed via quantitative and qualitative content analyses. The quantitative analysis was used to determine agenda-setting (number of articles) and, by coding articles, how priming was used in the descriptions of antidepressants. In the qualitative analysis, all articles were analyzed and condensed to determine which frames were used. Quantitative results: 271 articles were included. Agenda-setting was shown by a marked increase in the number of articles about antidepressants. Eight main codes were identified, with the negatively-associated side effects being the major one, thereby priming the public to use side effects as a criterion when judging antidepressants. Qualitative results: Two main frames were identified: 1) economic profits vs. medicine safety, and 2) the necessity of antidepressants. Both frames presented a critical view on antidepressants. It is believed that the media's agenda-setting, priming and framing of antidepressants led the public to have a more skeptical view on antidepressants, which may have probably contributed to a decrease in the usage of antidepressants. Copyright © 2017 Elsevier Inc. All rights reserved.

Toward a Phenomenological Account of Embodied Subjectivity in Autism.

PubMed

Boldsen, Sofie

2018-06-18

Sensorimotor research is currently challenging the dominant understanding of autism as a deficit in the cognitive ability to 'mindread'. This marks an emerging shift in autism research from a focus on the structure and processes of the mind to a focus on autistic behavior as grounded in the body. Contemporary researchers in sensorimotor differences in autism call for a reconciliation between the scientific understanding of autism and the first-person experience of autistic individuals. I argue that fulfilling this ambition requires a phenomenological understanding of the body as it presents itself in ordinary experience, namely as the subject of experience rather than a physical object. On this basis, I investigate how the phenomenology of Maurice Merleau-Ponty can be employed as a frame of understanding for bodily experience in autism. Through a phenomenological analysis of Tito Mukhopadhyay's autobiographical work, How can I talk if my lips don't move (2009), I illustrate the relevance and potential of phenomenological philosophy in autism research, arguing that this approach enables a deeper understanding of bodily and subjective experiences related to autism.

Representation of Gravity-Aligned Scene Structure in Ventral Pathway Visual Cortex.

PubMed

Vaziri, Siavash; Connor, Charles E

2016-03-21

The ventral visual pathway in humans and non-human primates is known to represent object information, including shape and identity [1]. Here, we show the ventral pathway also represents scene structure aligned with the gravitational reference frame in which objects move and interact. We analyzed shape tuning of recently described macaque monkey ventral pathway neurons that prefer scene-like stimuli to objects [2]. Individual neurons did not respond to a single shape class, but to a variety of scene elements that are typically aligned with gravity: large planes in the orientation range of ground surfaces under natural viewing conditions, planes in the orientation range of ceilings, and extended convex and concave edges in the orientation range of wall/floor/ceiling junctions. For a given neuron, these elements tended to share a common alignment in eye-centered coordinates. Thus, each neuron integrated information about multiple gravity-aligned structures as they would be seen from a specific eye and head orientation. This eclectic coding strategy provides only ambiguous information about individual structures but explicit information about the environmental reference frame and the orientation of gravity in egocentric coordinates. In the ventral pathway, this could support perceiving and/or predicting physical events involving objects subject to gravity, recognizing object attributes like animacy based on movement not caused by gravity, and/or stabilizing perception of the world against changes in head orientation [3-5]. Our results, like the recent discovery of object weight representation [6], imply that the ventral pathway is involved not just in recognition, but also in physical understanding of objects and scenes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Experimental investigation of the seismic performance of the R/C frames with reinforced masonry infills

NASA Astrophysics Data System (ADS)

Tanjung, Jafril; Maidiawati, Nugroho, Fajar

2017-10-01

Intensive studies regarding the investigation of seismic performance of reinforced concrete (R/C) frames which are infilled with brick masonry walls have been carried out by several researchers within the last three-decades. According to authors' field and experimentally experiences conclude that the unreinforced brick masonry infills significantly contributes to increase the seismic performance of the R/C frame structure. Unfortunately, the presence of brick masonry infill walls causes several undesirable effects such as short column, soft-storey, torsion and out of plane collapse. In this study, a strengthening technique for the brick masonry infills were experimentally investigated to improve the seismic performance of the R/C frame structures. For this purpose, four experimental specimens have been prepared, i.e. one of bare R/C frame (BF), one of R/C frame infilled with unreinforced brick-masonry wall (IFUM) and two of R/C frames were infilled with reinforced brick-masonry wall (IFRM-1 and IFRM-2). The bare frame and R/C frame infilled with unreinforced brick-masonry wall represents the typical R/C buildings' construction in Indonesia assuming the brick-masonry wall as the non-structural elements. The brick-masonry wall infills in specimens IFRM-1 and IFRM-2 were strengthened by using embedded ϕ4 plain steel bar on their diagonal and center of brick-masonry wall, respectively. All specimens were laterally pushed-over. The lateral loading and its lateral displacement, failure mechanism and their crack pattern were recorded during experimental works. Comparison of the experimental results of these four specimens conclude that the strengthening of the brick-masonry infills wall gave the significantly increasing of the seismic performance of the R/C frame. The seismic performance was evaluated based on the lateral strength of the R/C specimen. The embedded plain steel bar on brick-masonry also reduces the diagonal crack on the brick-masonry wall. It seems that the presence of the embedded plain bar may help reduce the vulnerability of the brick-masonry infill.

RECONSTRUCTING THREE-DIMENSIONAL JET GEOMETRY FROM TWO-DIMENSIONAL IMAGES

NASA Astrophysics Data System (ADS)

Avachat, Sayali; Perlman, Eric S.; Li, Kunyang; Kosak, Katie

2018-01-01

Relativistic jets in AGN are one of the most interesting and complex structures in the Universe. Some of the jets can be spread over hundreds of kilo parsecs from the central engine and display various bends, knots and hotspots. Observations of the jets can prove helpful in understanding the emission and particle acceleration processes from sub-arcsec to kilo parsec scales and the role of magnetic field in it. The M87 jet has many bright knots as well as regions of small and large bends. We attempt to model the jet geometry using the observed 2 dimensional structure. The radio and optical images of the jet show evidence of presence of helical magnetic field throughout. Using the observed structure in the sky frame, our goal is to gain an insight into the intrinsic 3 dimensional geometry in the jets frame. The structure of the bends in jet's frame may be quite different than what we see in the sky frame. The knowledge of the intrinsic structure will be helpful in understanding the appearance of the magnetic field and hence polarization morphology. To achieve this, we are using numerical methods to solve the non-linear equations based on the jet geometry. We are using the Log Likelihood method and algorithm based on Markov Chain Monte Carlo (MCMC) simulations.

A novel approach to enhance the accuracy of vibration control of Frames

NASA Astrophysics Data System (ADS)

Toloue, Iraj; Shahir Liew, Mohd; Harahap, I. S. H.; Lee, H. E.

2018-03-01

All structures built within known seismically active regions are typically designed to endure earthquake forces. Despite advances in earthquake resistant structures, it can be inferred from hindsight that no structure is entirely immune to damage from earthquakes. Active vibration control systems, unlike the traditional methods which enlarge beams and columns, are highly effective countermeasures to reduce the effects of earthquake loading on a structure. It requires fast computation of nonlinear structural analysis in near time and has historically demanded advanced programming hosted on powerful computers. This research aims to develop a new approach for active vibration control of frames, which is applicable over both elastic and plastic material behavior. In this study, the Force Analogy Method (FAM), which is based on Hook's Law is further extended using the Timoshenko element which considers shear deformations to increase the reliability and accuracy of the controller. The proposed algorithm is applied to a 2D portal frame equipped with linear actuator, which is designed based on full state Linear Quadratic Regulator (LQR). For comparison purposes, the portal frame is analysed by both the Euler Bernoulli and Timoshenko element respectively. The results clearly demonstrate the superiority of the Timoshenko element over Euler Bernoulli for application in nonlinear analysis.

Identifying perceptions of academic reform in pharmacy using a four-frame organizational change model.

PubMed

Bajis, Dalia; Chaar, Betty; Basheti, Iman A; Moles, Rebekah

2017-11-10

In an ever-changing environment, pharmacy education is in the race to catch up and excel to produce competent pharmacists. Examining academic institutions, including schools of pharmacy, their internal systems and framework, it seems appropriate to view these institutions using multiple lenses. Bolman and Deal conceptualized a method to examine organizations using four constructs (structural, human resource, political, and symbolic). The Eastern Mediterranean Region (EMR), with deep-rooted pharmacy education and practice was the setting for this research. To explore factors affecting academic reform in undergraduate pharmacy education in the EMR from stakeholders' and students' perspectives; and to apply Bolman and Deal's four-frame organizational change model to explore how these issues might be viewed. A multiple-method approach was employed and involved collecting, analyzing and integrating qualitative semi-structured interview data with open-ended questions in a survey. Cross-sector stakeholder sample from various EMR countries was recruited and interviewed. Final year pharmacy students from one school of pharmacy in Jordan were surveyed. Emergent themes were indicative that academic reform was addressed by all frames of the Bolman and Deal model. Structural and political frames received substantial weighing pointing to the importance of curricular reform, collaboration and leadership. A need for skillful and role-model teaching academic staff was highlighted, and in harmony with the human resource frame. Issues within the symbolic frame were readily apparent in the data and spanned the other three frames in relation to heritage, customs and cultural barriers. Issues pertinent to academic reform in pharmacy were presented. Viewing change in pharmacy schools from multiple perspectives highlighted the need for structural changes to pharmacy programs, human resource management, political will, leadership, and collaboration. The importance of understanding cultural aspects of organizations is critical as it is these that provide identity to any organization and help reformers better manage change. Copyright © 2017 Elsevier Inc. All rights reserved.

Comparison and Analysis of Steel Frame Based on High Strength Column and Normal Strength Column

NASA Astrophysics Data System (ADS)

Liu, Taiyu; An, Yuwei

2018-01-01

The anti-seismic performance of high strength steel has restricted its industrialization in civil buildings. In order to study the influence of high strength steel column on frame structure, three models are designed through MIDAS/GEN finite element software. By comparing the seismic performance and economic performance of the three models, the three different structures are comprehensively evaluated to provide some references for the development of high strength steel in steel structure.

Direct Estimation of Structure and Motion from Multiple Frames

DTIC Science & Technology

1990-03-01

sequential frames in an image sequence. As a consequence, the information that can be extracted from a single optical flow field is limited to a snapshot of...researchers have developed techniques that extract motion and structure inform.4tion without computation of the optical flow. Best known are the "direct...operated iteratively on a sequence of images to recover structure. It required feature extraction and matching. Broida and Chellappa [9] suggested the use of

Composite Structure Modeling and Analysis of Advanced Aircraft Fuselage Concepts

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek; Sorokach, Michael R.

2015-01-01

NASA Environmentally Responsible Aviation (ERA) project and the Boeing Company are collabrating to advance the unitized damage arresting composite airframe technology with application to the Hybrid-Wing-Body (HWB) aircraft. The testing of a HWB fuselage section with Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) construction is presently being conducted at NASA Langley. Based on lessons learned from previous HWB structural design studies, improved finite-element models (FEM) of the HWB multi-bay and bulkhead assembly are developed to evaluate the performance of the PRSEUS construction. In order to assess the comparative weight reduction benefits of the PRSEUS technology, conventional cylindrical skin-stringer-frame models of a cylindrical and a double-bubble section fuselage concepts are developed. Stress analysis with design cabin-pressure load and scenario based case studies are conducted for design improvement in each case. Alternate analysis with stitched composite hat-stringers and C-frames are also presented, in addition to the foam-core sandwich frame and pultruded rod-stringer construction. The FEM structural stress, strain and weights are computed and compared for relative weight/strength benefit assessment. The structural analysis and specific weight comparison of these stitched composite advanced aircraft fuselage concepts demonstrated that the pressurized HWB fuselage section assembly can be structurally as efficient as the conventional cylindrical fuselage section with composite stringer-frame and PRSEUS construction, and significantly better than the conventional aluminum construction and the double-bubble section concept.

Temporal framing and the hidden-zero effect: rate-dependent outcomes on delay discounting.

PubMed

Naudé, Gideon P; Kaplan, Brent A; Reed, Derek D; Henley, Amy J; DiGennaro Reed, Florence D

2018-05-01

Recent research suggests that presenting time intervals as units (e.g., days) or as specific dates, can modulate the degree to which humans discount delayed outcomes. Another framing effect involves explicitly stating that choosing a smaller-sooner reward is mutually exclusive to receiving a larger-later reward, thus presenting choices as an extended sequence. In Experiment 1, participants (N = 201) recruited from Amazon Mechanical Turk completed the Monetary Choice Questionnaire in a 2 (delay framing) by 2 (zero framing) design. Regression suggested a main effect of delay, but not zero, framing after accounting for other demographic variables and manipulations. We observed a rate-dependent effect for the date-framing group, such that those with initially steep discounting exhibited greater sensitivity to the manipulation than those with initially shallow discounting. Subsequent analyses suggest these effects cannot be explained by regression to the mean. Experiment 2 addressed the possibility that the null effect of zero framing was due to within-subject exposure to the hidden- and explicit-zero conditions. A new Amazon Mechanical Turk sample completed the Monetary Choice Questionnaire in either hidden- or explicit-zero formats. Analyses revealed a main effect of reward magnitude, but not zero framing, suggesting potential limitations to the generality of the hidden-zero effect. © 2018 Society for the Experimental Analysis of Behavior.

Framing Indoor Tanning Warning Messages to Reduce Skin Cancer Risks Among Young Women: Implications for Research and Policy

PubMed Central

Tercyak, Kenneth P.

2015-01-01

Objectives. We investigated the impact of indoor tanning device warnings that communicate the risks associated with indoor tanning (i.e., loss framed) or the benefits of avoiding indoor tanning (i.e., gain framed). Methods. A convenience sample of non-Hispanic White women aged 18 to 30 years who tanned indoors at least once in the past year (n = 682) participated in a within-subjects experiment. Participants completed baseline measures and reported indoor tanning intentions and intentions to quit indoor tanning in response to 5 warning messages in random order. A text-only control warning was based on Food and Drug Administration–required warnings for indoor tanning devices. Experimental warnings included graphic content and were either gain or loss framed. Results. In multivariable analyses, gain-framed warnings did not differ from the control warning on women’s intentions to tan indoors, but they prompted stronger intentions to quit than the control message. Loss-framed warnings significantly reduced intentions to tan indoors and increased intentions to quit indoor tanning compared with control and gain-framed warnings. Conclusions. The public health impact of indoor tanning device warnings can be enhanced by incorporating graphic content and leveraging gain- and loss-framed messaging. PMID:26066932

Short and Sweet: The Persuasive Effects of Message Framing and Temporal Context in Antismoking Warning Labels.

PubMed

Mollen, Saar; Engelen, Susanne; Kessels, Loes T E; van den Putte, Bas

2017-01-01

Current warning labels on cigarette packages are generally focused on long-term losses that can be incurred if one continues smoking. This study compares the effects of these labels against warning labels that stress short-term losses of smoking as well as labels that stress short- and long-term benefits that can be obtained when one quits smoking. A 2 (message frame: gain vs. loss) × 2 (temporal context: short vs. long term) between-subjects experiment was conducted among 132 smokers, with attitude toward quitting smoking and intention to quit smoking, as well as information-seeking behavior and message recall, as the dependent variables. Findings were in line with theory regarding message framing and temporal discounting, showing enhanced effects of gain over loss frames and short-term over long-term consequences on warning labels for attitudes and intentions. In addition, an interaction between message frame and temporal context was found. Especially, gain-framed messages showed stronger effects on intentions to quit smoking than loss-framed messages when warning labels concerned short-term outcomes. Findings suggest that current warning labels, with an emphasis on long-term negative health outcomes, should be reconsidered.

Review of Research and Application of Reinforced Concrete Structures Strengthened by Braces

NASA Astrophysics Data System (ADS)

Gong, Jing; Zhu, Zezhong; Zeng, Cong

2017-06-01

Many of RC frame structures are urgently needed to be strengthened and maintained due to the increase of service life, the change of use function, and the impact of natural disasters. This paper reviews the research status of strengthening RC structures with braces; introduces the features and connection forms of joints connecting with braces; summarizes the engineering application of buckling-restrained braces, pointing out that buckling-restrained brace is an effective means to strengthen the RC frame structures with more reliable performance and broad application prospect.

An alternative clinical routine for subjective refraction based on power vectors with trial frames.

PubMed

María Revert, Antonia; Conversa, Maria Amparo; Albarrán Diego, César; Micó, Vicente

2017-01-01

Subjective refraction determines the final point of refractive error assessment in most clinical environments and its foundations have remained unchanged for decades. The purpose of this paper is to compare the results obtained when monocular subjective refraction is assessed in trial frames by a new clinical procedure based on a pure power vector interpretation with conventional clinical refraction procedures. An alternative clinical routine is described that uses power vector interpretation with implementation in trial frames. Refractive error is determined in terms of: (i) the spherical equivalent (M component), and (ii) a pair of Jackson Crossed Cylinder lenses oriented at 0°/90° (J 0 component) and 45°/135° (J 45 component) for determination of astigmatism. This vector subjective refraction result (VR) is compared separately for right and left eyes of 25 subjects (mean age, 35 ± 4 years) against conventional sphero-cylindrical subjective refraction (RX) using a phoropter. The VR procedure was applied with both conventional tumbling E optotypes (VR1) and modified optotypes with oblique orientation (VR2). Bland-Altman plots and intra-class correlation coefficient showed good agreement between VR, and RX (with coefficient values above 0.82) and anova showed no significant differences in any of the power vector components between RX and VR. VR1 and VR2 procedure results were similar (p ≥ 0.77). The proposed routine determines the three components of refractive error in power vector notation [M, J 0 , J 45 ], with a refraction time similar to the one used in conventional subjective procedures. The proposed routine could be helpful for inexperienced clinicians and for experienced clinicians in those cases where it is difficult to get a valid starting point for conventional RX (irregular corneas, media opacities, etc.) and for refractive situations/places with inadequate refractive facilities/equipment. © 2016 The Authors Ophthalmic & Physiological Optics © 2016 The College of Optometrists.

Altered risk-aversion and risk-taking behaviour in patients with Alzheimer's disease.

PubMed

Ha, Juwon; Kim, Eun-Jin; Lim, Sewon; Shin, Dong-Won; Kang, Yeo-Jin; Bae, Seung-Min; Yoon, Hyung-Kun; Oh, Kang-Seob

2012-09-01

Normal individuals are risk averse for decisions framed as gains but risk taking for decisions framed as losses. This framing effect is supposed to be attenuated in Alzheimer's disease (AD) patients. We investigated the effects of highlighting rewards versus highlighting punishments on the risky decision-making of AD patients. Fourteen mild to moderate AD patients (Mini-Mental Status Examination score, 11-23; Clinical Dementia Rating, 1-2) and 16 healthy volunteers were recruited for the study. Subjects completed a computerized task on risky decision-making in which mathematically equivalent dilemmas were presented in terms of opportunities to gain monetary rewards ('positive frame') or avoid suffering losses ('negative frame'). As expected, AD patients chose more risky options under the positive frame than the negative frame, contrary to the control group (Z =-2.671, P= 0.007). The normal difference in the distribution of risky choices between positively and negatively framed dilemmas was significantly reduced in the AD group after we adjusted for years of education, mean age and depression (F= 5.321, P= 0.030). Deliberation time did not differ significantly between the two groups. These results suggest that AD patients making high-risk choices is associated with attenuated sensitivity to the emotional frames that highlight rewards or punishments, possibly reflecting altered evaluations of prospective gains and losses. © 2012 The Authors. Psychogeriatrics © 2012 Japanese Psychogeriatric Society.

The effects of narrative and message framing on engagement and eating intention among a sample of adult Hispanics.

PubMed

Wirtz, John G; Kulpavaropas, Supathida

2014-01-01

To test the effect of narrative messages and gain- and loss-framed messages on persuasive outcomes with a sample of Hispanic adults. A 2 (message type: narrative, non-narrative) × 2 (message frame: gain-framed, loss-framed) between subjects posttest only. Data were collected at 2 outdoor festivals in West Texas. Participants were a convenience sample of 72 Hispanic adults (mean age, 40.6 years). Main outcome measures were message engagement, message relevance, attitude toward message, healthy eating intention, and physical activity intention. Data analysis included analysis of variance and multivariate analysis of variance. There was no significant difference between narrative and non-narrative messages. Gain-framed messages were rated more positively, whereas loss-framed messages were considered more engaging and also produced higher intentions to eat healthy and to become physically active. The interaction between message type and message framing was not significant. Loss-framed messages produced the unanticipated effect of higher message engagement and higher intention. This finding suggests that messages emphasizing losses associated with unhealthy eating and lack of physical activity may be more effective when targeting Hispanic adults than messages emphasizing potential gains. The lack of difference between narrative and non-narrative messages suggests there is no disadvantage to using narratives, but also no advantage. Copyright © 2014 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

Compressive Behavior of Frame-Stiffened Composite Panels

NASA Technical Reports Server (NTRS)

Yovanof, Nicolette P.; Jegley, Dawn C.

2011-01-01

New technologies are being developed under NASA's Environmentally Responsible Aviation (ERA) Program aimed at reducing fuel burn and emissions in large commercial aircraft. A Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept is being developed which offers advantages over traditional metallic structure. In this concept a stitched carbon-epoxy material system is employed with the potential for reducing the weight and cost of transport aircraft structure by eliminating fasteners and producing a more damage tolerant design. In addition, by adding unidirectional carbon rods to the top of stiffeners and minimizing the interference between the sandwich frames and the rod-stiffened stringers, the panel becomes more structurally efficient. This document describes the results of experimentation on a PRSEUS panel in which the frames are loaded in unidirectional compression beyond the local buckling of the skin of a Hybrid Wing Body (HWB) aircraft. A comparison with analytical predictions and the relationship between these test results and the global aircraft design is presented.

D Visualization of a Timber Frame Historic Building: Partite Usage and its Impact on the Structural System

NASA Astrophysics Data System (ADS)

Günay, S.

2017-08-01

Throughout their lifetime, historic buildings might be altered for different kind of usage for different purposes. If this new function or new usage requires utilization of the building in separate units, this separation might affect the historic building's functionality and structure and as a result its overall condition. Yorguc Pasa Mansion conservation project was prepared as a part of the Middle East Technical University (METU) Master's Program in Documentation and Conservation of Historic Monuments and Sites for the historic Yorguc Pasa Mansion. The mansion is a 19th century Ottoman Period timber frame building in Amasya, a Black Sea Region city in Turkey that has traces from different civilizations such as Hittites, Greeks, Romans and Ottomans. This paper aims to discuss the affects of the partite usage on structural conditions of timber frame buildings with the case study of Amasya Yorguc Pasa Mansion through the 3D visualized structural systems.

Increased plasma soluble adhesion molecules; ICAM-1, VCAM-1, and E-selectin levels in patients with slow coronary flow.

PubMed

Turhan, Hasan; Saydam, Gul Sevim; Erbay, Ali Riza; Ayaz, Selime; Yasar, Ayse Saatci; Aksoy, Yuksel; Basar, Nurcan; Yetkin, Ertan

2006-04-04

Inflammation has been reported to be a major contributing factor to many cardiovascular events. In the present study, we aimed to evaluate plasma soluble adhesion molecules; intercellular adhesion molecule-1 (ICAM-1), vascular cell adhesion molecule-1 (VCAM-1) and E-selectin as possible indicators of endothelial activation or inflammation in patients with slow coronary flow. Study population included 17 patients with angiographically proven normal coronary arteries and slow coronary flow in all three coronary vessels (group I, 11 male, 6 female, mean age=48+/-9 years), and 20 subjects with angiographically proven normal coronary arteries without associated slow coronary flow (group II, 11 male, 9 female, mean age=50+/-8 years). Coronary flow rates of all patients and control subjects were documented by Thrombolysis In Myocardial Infarction frame count (TIMI frame count). All patients in group I had TIMI frame counts greater than two standard deviation above those of control subjects (group II) and, therefore, were accepted as exhibiting slow coronary flow. Serum levels of ICAM-1, VCAM-1, and E-selectin were measured in all patients and control subjects using commercially available ELISA kits. Serum ICAM-1, VCAM-1, and E-selectin levels of patients with slow coronary flow were found to be significantly higher than those of control subjects with normal coronary flow (ICAM-1: 545+/-198 ng/ml vs. 242+/-113 ng/ml respectively, p<0.001, VCAM-1: 2040+/-634 ng/ml vs. 918+/-336 ng/ml respectively, p<0.001, E-selectin: 67+/-9 ng/ml vs. 52+/-8 ng/ml respectively, p<0.001). Average TIMI frame count was detected to be significantly correlated with plasma soluble ICAM-1 (r=0.550, p<0.001), VCAM-1 (r=0.569, p<0.001) and E-selectin (r=0.443, p=0.006). Increased levels of soluble adhesion molecules in patients with slow coronary flow may be an indicator of endothelial activation and inflammation and are likely to be in the causal pathway leading to slow coronary flow.

Does the Integration of Haptic and Visual Cues Reduce the Effect of a Biased Visual Reference Frame on the Subjective Head Orientation?

PubMed Central

Gueguen, Marc; Vuillerme, Nicolas; Isableu, Brice

2012-01-01

Background The selection of appropriate frames of reference (FOR) is a key factor in the elaboration of spatial perception and the production of robust interaction with our environment. The extent to which we perceive the head axis orientation (subjective head orientation, SHO) with both accuracy and precision likely contributes to the efficiency of these spatial interactions. A first goal of this study was to investigate the relative contribution of both the visual and egocentric FOR (centre-of-mass) in the SHO processing. A second goal was to investigate humans' ability to process SHO in various sensory response modalities (visual, haptic and visuo-haptic), and the way they modify the reliance to either the visual or egocentric FORs. A third goal was to question whether subjects combined visual and haptic cues optimally to increase SHO certainty and to decrease the FORs disruption effect. Methodology/Principal Findings Thirteen subjects were asked to indicate their SHO while the visual and/or egocentric FORs were deviated. Four results emerged from our study. First, visual rod settings to SHO were altered by the tilted visual frame but not by the egocentric FOR alteration, whereas no haptic settings alteration was observed whether due to the egocentric FOR alteration or the tilted visual frame. These results are modulated by individual analysis. Second, visual and egocentric FOR dependency appear to be negatively correlated. Third, the response modality enrichment appears to improve SHO. Fourth, several combination rules of the visuo-haptic cues such as the Maximum Likelihood Estimation (MLE), Winner-Take-All (WTA) or Unweighted Mean (UWM) rule seem to account for SHO improvements. However, the UWM rule seems to best account for the improvement of visuo-haptic estimates, especially in situations with high FOR incongruence. Finally, the data also indicated that FOR reliance resulted from the application of UWM rule. This was observed more particularly, in the visual dependent subject. Conclusions: Taken together, these findings emphasize the importance of identifying individual spatial FOR preferences to assess the efficiency of our interaction with the environment whilst performing spatial tasks. PMID:22509295

Effectiveness of damped braces to mitigate seismic torsional response of unsymmetric-plan buildings

NASA Astrophysics Data System (ADS)

Mazza, Fabio; Pedace, Emilia; Favero, Francesco Del

2017-02-01

The seismic retrofitting of unsymmetric-plan reinforced concrete (r.c.) framed buildings can be carried out by the incorporation of damped braces (DBs). Yet most of the proposals to mitigate the seismic response of asymmetric framed buildings by DBs rest on the hypothesis of elastic (linear) structural response. The aim of the present work is to evaluate the effectiveness and reliability of a Displacement-Based Design procedure of hysteretic damped braces (HYDBs) based on the nonlinear behavior of the frame members, which adopts the extended N2 method considered by Eurocode 8 to evaluate the higher mode torsional effects. The Town Hall of Spilinga (Italy), a framed structure with an L-shaped plan built at the beginning of the 1960s, is supposed to be retrofitted with HYDBs to attain performance levels imposed by the Italian seismic code (NTC08) in a high-risk zone. Ten structural solutions are compared by considering two in-plan distributions of the HYDBs, to eliminate (elastic) torsional effects, and different design values of the frame ductility combined with a constant design value of the damper ductility. A computer code for the nonlinear dynamic analysis of r.c. spatial framed structures is adopted to evaluate the critical incident angle of bidirectional earthquakes. Beams and columns are simulated with a lumped plasticity model, including flat surface modeling of the axial load-biaxial bending moment elastic domain at the end sections, while a bilinear law is used to idealize the behavior of the HYDBs. Damage index domains are adopted to estimate the directions of least seismic capacity, considering artificial earthquakes whose response spectra match those adopted by NTC08 at serviceability and ultimate limit states.

The Populist Chameleon: The People's Party, Huey Long, George Wallace, and the Populist Argumentative Frame

ERIC Educational Resources Information Center

Lee, Michael J.

2006-01-01

This essay argues that a sustained form can be located in the complicated history of populist rhetoric. Despite its chameleonic qualities, the advancement of populism is constituted by alterations in the focus and content, not the structure, of populist activism. This structure, or what I term its argumentative frame, positions a virtuous people…

Pushover analysis of reinforced concrete frames considering shear failure at beam-column joints

NASA Astrophysics Data System (ADS)

Sung, Y. C.; Lin, T. K.; Hsiao, C. C.; Lai, M. C.

2013-09-01

Since most current seismic capacity evaluations of reinforced concrete (RC) frame structures are implemented by either static pushover analysis (PA) or dynamic time history analysis, with diverse settings of the plastic hinges (PHs) on such main structural components as columns, beams and walls, the complex behavior of shear failure at beam-column joints (BCJs) during major earthquakes is commonly neglected. This study proposes new nonlinear PA procedures that consider shear failure at BCJs and seek to assess the actual damage to RC structures. Based on the specifications of FEMA-356, a simplified joint model composed of two nonlinear cross struts placed diagonally over the location of the plastic hinge is established, allowing a sophisticated PA to be performed. To verify the validity of this method, the analytical results for the capacity curves and the failure mechanism derived from three different full-size RC frames are compared with the experimental measurements. By considering shear failure at BCJs, the proposed nonlinear analytical procedures can be used to estimate the structural behavior of RC frames, including seismic capacity and the progressive failure sequence of joints, in a precise and effective manner.

Thermal Structures Technology Development for Reusable Launch Vehicle Cryogenic Propellant Tanks

NASA Technical Reports Server (NTRS)

Johnson, Theodore F.; Natividad, Roderick; Rivers, H. Kevin; Smith, Russell

1998-01-01

Analytical and experimental studies conducted at the NASA Langley Research Center for investigating integrated cryogenic propellant tank systems for a Reusable Launch Vehicle are described. The cryogenic tanks are investigated as an integrated tank system. An integrated tank system includes the tank wall, cryogenic insulation, Thermal Protection System (TPS) attachment sub-structure, and TPS. Analysis codes are used to size the thicknesses of cryogenic insulation and TPS insulation for thermal loads, and to predict tank buckling strengths at various ring frame spacings. The unique test facilities developed for the testing of cryogenic tank components are described. Testing at cryogenic and high-temperatures verifies the integrity of materials, design concepts, manufacturing processes, and thermal/structural analyses. Test specimens ranging from the element level to the subcomponent level are subjected to projected vehicle operational mechanical loads and temperatures. The analytical and experimental studies described in this paper provide a portion of the basic information required for the development of light-weight reusable cryogenic propellant tanks.

Thermal Structures Technology Development for Reusable Launch Vehicle Cryogenic Propellant Tanks

NASA Technical Reports Server (NTRS)

Johnson, Theodore F.; Natividad, Roderick; Rivers, H. Kevin; Smith, Russell W.

2005-01-01

Analytical and experimental studies conducted at the NASA, Langley Research Center (LaRC) for investigating integrated cryogenic propellant tank systems for a reusable launch vehicle (RLV) are described. The cryogenic tanks are investigated as an integrated tank system. An integrated tank system includes the tank wall, cryogenic insulation, thermal protection system (TPS) attachment sub-structure, and TPS. Analysis codes are used to size the thicknesses of cryogenic insulation and TPS insulation for thermal loads, and to predict tank buckling strengths at various ring frame spacings. The unique test facilities developed for the testing of cryogenic tank components are described. Testing at cryogenic and high-temperatures verifies the integrity of materials, design concepts, manufacturing processes, and thermal/structural analyses. Test specimens ranging from the element level to the subcomponent level are subjected to projected vehicle operational mechanical loads and temperatures. The analytical and experimental studies described in this paper provide a portion of the basic information required for the development of light-weight reusable cryogenic propellant tanks.

Modelling of masonry infill walls participation in the seismic behaviour of RC buildings using OpenSees

NASA Astrophysics Data System (ADS)

Furtado, André; Rodrigues, Hugo; Arêde, António

2015-06-01

Recent earthquakes show that masonry infill walls should be taken into account during the design and assessment process of structures, since this type of non-structural elements increase the in-plane stiffness of the structure and consequently the natural period. An overview of the past researches conducted on the modelling of masonry infilled frame issues has been done, with discussion of past analytical investigations and different modelling approaches that many authors have proposed, including micro- and macro-modelling strategies. After this, the present work presents an improved numerical model, based on the Rodrigues et al. (J Earthq Eng 14:390-416, 2010) approach, for simulating the masonry infill walls behaviour in the computer program OpenSees. The main results of the in-plane calibration analyses obtained with one experimental test are presented and discussed. For last, two reinforced concrete regular buildings were studied and subjected to several ground motions, with and without infills' walls.

Cassette less SOFC stack and method of assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meinhardt, Kerry D

2014-11-18

A cassette less SOFC assembly and a method for creating such an assembly. The SOFC stack is characterized by an electrically isolated stack current path which allows welded interconnection between frame portions of the stack. In one embodiment electrically isolating a current path comprises the step of sealing a interconnect plate to a interconnect plate frame with an insulating seal. This enables the current path portion to be isolated from the structural frame an enables the cell frame to be welded together.

Interactive Multiple-Representation Editing of Physically-based 3D Animation

DTIC Science & Technology

1994-05-29

view similar to that of FrameMaker [46], but with a stronger model of structured editing, and a language window, which displays a formal description of...used. This is partly a result of the power of a good direct manipulation editor { most users of good editors like FrameMaker don’t seem to miss having a...re nement. In SIG- GRAPH, pages 205{212, August 1988. [46] Frame Technology Inc. Using FrameMaker , 1990. [47] Bjorn N. Freeman-Benson and John Maloney

A serial mediation model of message framing on intentions to receive the human papillomavirus (HPV) vaccine: revisiting the role of threat and efficacy perceptions.

PubMed

Krieger, Janice L; Sarge, Melanie A

2013-01-01

Previous research has yielded mixed findings regarding the potential for message framing to influence HPV vaccine-related intentions. Drawing on the Extended Parallel Process Model (EPPM), the current study focuses on the role of threat and efficacy as serial mediators linking message framing and HPV vaccine-related intentions. College-age females and their parents participated in a between-subjects, posttest only experiment to investigate whether behavioral intentions to talk to a doctor about the HPV vaccine differ as a function of framing messages in terms of disease prevention. For young women, framing messages as preventing genital warts (as compared to cancer prevention) significantly increased perceptions of self-efficacy, which enhanced response efficacy perceptions that, in turn, increased intentions to talk to a doctor about the HPV vaccine. There were no effects of message framing among parents. However, response efficacy was a significant mediator of self-efficacy and behavioral intentions for both the college-age females and their parents. The results of this study suggest new approaches for considering the relationship among EPPM constructs.

Some aspects of an induced electric dipole moment in rotating and non-rotating frames.

PubMed

Oliveira, Abinael B; Bakke, Knut

2017-06-01

Quantum effects on a neutral particle (atom or molecule) with an induced electric dipole moment are investigated when it is subject to the Kratzer potential and a scalar potential proportional to the radial distance. In addition, this neutral is placed in a region with electric and magnetic fields. This system is analysed in both non-rotating and rotating reference frames. Then, it is shown that bound state solutions to the Schrödinger equation can be achieved and, in the search for polynomial solutions to the radial wave function, a restriction on the values of the cyclotron frequency is analysed in both reference frames.

Failure at Frame-Stringer Intersections in PRSEUS Panels

NASA Technical Reports Server (NTRS)

Jegley, Dawn C.

2012-01-01

NASA, the Air Force Research Laboratory and The Boeing Company have worked to develop new low-cost, light-weight composite structures for aircraft. A Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept has been developed which offers advantages over traditional metallic structures. In this concept a stitched carbon-epoxy material system has been developed with the potential for reducing the weight and cost of transport aircraft structure by eliminating fasteners, thereby reducing part count and labor. By adding unidirectional carbon rods to the top of stiffeners, the panel becomes more structurally efficient. This combination produces a more damage tolerant design. This study focuses on the intersection between the rod-stiffener and the foam-filled frame in a PRSEUS specimen. Compression loading is considered, which induces stress concentrations at the intersection point that can lead to failures. An experiment with accompanying analysis for a single-frame specimen is described, followed by a parametric study of simple reinforcements to reduce strains in the intersection region.

Technological Frame Incongruence, Diffusion, and Noncompliance

NASA Astrophysics Data System (ADS)

Sobreperez, Polly

The technological frames of reference strand of social shaping of technology theory is used to overlay the issues arising from a case study looking at noncompliance with information systems. A recent review of the theory suggests that although frame content is often addressed, frame structure, the process of framing, and the characteristics and outcomes of frames are largely overlooked. This paper attempts to address this shortfall by applying the indicators identified by case study research to the frames of different groups and using them to highlight differing perceptions and attitudes. In this way, the author suggests that issues surrounding noncompliance should not be dismissed as resistance but instead should be further studied by managers and developers, leading to accommodation of differing views. Further examination of frame incongruence reveals dependence on inefficient or ineffective organizational situations and thus these indicators can be useful in future studies to identify and address procedural, acceptance and cultural issues leading to acts of noncompliance.

Crash fatality risk and unibody versus body-on-frame structure in SUVs.

PubMed

Ossiander, Eric M; Koepsell, Thomas D; McKnight, Barbara

2014-09-01

In crashes between cars and SUVs, car occupants are more likely to be killed than if they crashed with another car. An increasing proportion of SUVs are built with unibody, rather than truck-like body-on-frame construction. Unibody SUVs are generally lighter, less stiff, and less likely to roll over than body-on-frame SUVs, but whether unibody structure affects risk of death in crashes is unknown. To determine whether unibody SUVs differ from body-on-frame SUVs in the danger they pose to occupants of other vehicles and in the self-protection they offer to their own occupants. Case-control study of crashes between one compact SUV and one other passenger vehicle in the US during 1995-2008, in which the SUV was model year 1996-2006. Cases were all decedents in fatal crashes, one control was selected from each non-fatal crash. Occupants of passenger vehicles that crashed with compact unibody SUVs were at 18% lower risk of death compared to those that crashed with compact body-on-frame SUVs (adjusted odds ratio 0.82 (95% confidence interval 0.73-0.94)). Occupants of compact unibody SUVs were also at lower risk of death compared to occupants of body-on-frame SUVs (0.86 (0.72-1.02)). In two-vehicle collisions involving compact SUVs, unibody structure was associated with lower risk of death both in occupants of other vehicles in the crash, and in SUVs' own occupants. Copyright © 2014 Elsevier Ltd. All rights reserved.

"State Your Defense!" Children Negotiate Analytic Frames in the Context of Deliberative Dialogue

ERIC Educational Resources Information Center

Hauver, Jennifer

2017-01-01

The purpose of this exploratory study was to identify the analytic frames children (ages 9 to 11) employed as they worked together to make sense of an ill-structured problem, what those same children did when their frames collided in the context of deliberative dialogue, and what they learned from the process of negotiation. Data included pre- and…

Perceived Risk as a Moderator of the Effectiveness of Framed HIV Test Promotion Messages Among Women: A Randomized Controlled Trial

PubMed Central

Hull, Shawnika J

2014-01-01

Objective Researchers argue that gain framed messages should be more effective for prevention behaviors while loss frames should be more effective for detection behaviors (Rothman & Salovey, 1997). Evidence for this taxonomy has been mixed. This study examines whether the effects of gain and loss framed messages on HIV testing intentions is moderated by perceived risk of a positive result. Methods This experiment was conducted on-line and utilizes a single factor (frame: gain/loss) between subjects design, with a separate HIV test promotion control and a no message control to examine whether perceived risk of a positive test result moderates the effects of framed messages on intentions to seek an HIV test in the next 3 months. The sample (N=1052; age M = 22, SD = 2.22), recruited through Survey Sampling International, included 51% Black women (49% White women). Results HIV test promotion messages were more effective than no message but there were no other main effects for condition. Results also demonstrate a significant interaction between message frame and perceived risk, which is mediated through elaborative processing of the message. The interaction demonstrated an advantage for the loss framed message among women with some perceived risk and an advantage for the gain framed message among women with low perceived risk. Conclusion Results imply that the prevention/detection function of the behavior may be an inadequate distinction in the consideration of the effectiveness of framed messages promoting HIV testing. Rather, this study demonstrates that risk perceptions are an important moderator of framing effects. PMID:21767018

Perceived risk as a moderator of the effectiveness of framed HIV-test promotion messages among women: a randomized controlled trial.

PubMed

Hull, Shawnika J

2012-01-01

Researchers argue that gain-framed messages should be more effective for prevention behaviors, while loss frames should be more effective for detection behaviors (Rothman & Salovey, 1997). Evidence for this taxonomy has been mixed. This study examines whether the effects of gain- and loss-framed messages on HIV-testing intentions is moderated by perceived risk of a positive result. This experiment was conducted online and utilized a single factor (frame: gain/loss) between subjects design, with a separate HIV-test promotion control and a no message control to examine whether perceived risk of a positive test result moderates the effects of framed messages on intentions to seek an HIV test in the next 3 months. The sample (N = 1052; M age = 22, SD = 2.22), recruited through Survey Sampling International, included 51% Black women (49% White women). HIV-test promotion messages were more effective than no message, but there were no other main effects for condition. Results also demonstrated a significant interaction between message frame and perceived risk, which is mediated through elaborative processing of the message. The interaction demonstrated an advantage for the loss-framed message among women with some perceived risk and an advantage for the gain-framed message among women with low perceived risk. Results imply that the prevention/detection function of the behavior may be an inadequate distinction in the consideration of the effectiveness of framed messages promoting HIV testing. Rather, this study demonstrates that risk perceptions are an important moderator of framing effects.

Band structure of comb-like photonic crystals containing meta-materials

NASA Astrophysics Data System (ADS)

Weng, Yi; Wang, Zhi-Guo; Chen, Hong

2007-09-01

We study the transmission properties and band structure of comb-like photonic crystals (PC) with backbones constructed of meta-materials (negative-index materials) within the frame of the interface response theory. The result shows the existence of a special band gap at low frequency. This gap differs from the Bragg gaps in that it is insensitive to the geometrical scaling and disorder. In comparison with the zero-average-index gap in one-dimensional PC made of alternating positive- and negative-index materials, the gap is obviously deeper and broader, given the same system parameters. In addition, the behavior of its gap-edges is also different. One gap-edge is decided by the average permittivity whereas the other is only subject to the changing of the permeability of the backbone. Due to this asymmetry of the two gap-edges, the broadening of the gap could be realized with much freedom and facility.

Controllable outrigger damping system for high rise building with MR dampers

NASA Astrophysics Data System (ADS)

Wang, Zhihao; Chang, Chia-Ming; Spencer, Billie F., Jr.; Chen, Zhengqing

2010-04-01

A novel energy dissipation system that can achieve the amplified damping ratio for a frame-core tube structures is explored, where vertical dampers are equipped between the outrigger and perimeter columns. The modal characteristics of the structural system with linear viscous dampers are theoretically analyzed from the simplified finite element model by parametric analysis. The result shows that modal damping ratios of the first several modes can increase a lot with this novel damping system. To improve the control performance of system, the semi-active control devices, magnetorheological (MR) dampers, are adopted to develop a controllable outrigger damping system. The clipped optimal control with the linear-quadratic Gaussian (LQG) acceleration feedback is adopted in this paper. The effectiveness of both passive and semi-active control outrigger damping systems is evaluated through the numerical simulation of a representative tall building subjected to two typical earthquake records.

Testing the effects of message framing, kernel state, and exercise guideline adherence on exercise intentions and resolve.

PubMed

de Bruijn, Gert-Jan; Out, Kim; Rhodes, Ryan E

2014-11-01

To study the effects of framed messages on exercise intention and resolve. Two (type of frame: gain or loss) × 2 (type of kernel state: desirable or undesirable outcome) post-test study. Participants were recruited online and questioned about their previous exercise behaviour and their exercise risk perception. After this, they were randomly allocated to one of four messages that were different in terms of positive or negative outcomes (type of frame) and in terms of attained or avoided outcomes (type of kernel state). After reading the message, participants indicated their intention and resolve to engage in sufficient exercise. No effects were found for intention. For resolve, there was a significant interaction between type of frame, type of kernel state, and exercise adherence. Those who did not adhere to the exercise guideline and read the loss-framed message with attained outcomes reported significantly higher resolve than all other participants. This study indicates the relevance of including attained outcomes in message framing exercise interventions as well as a focus on exercise resolve. What is already known on this subject? Message framing is commonly used to increase exercise intentions and behaviour. Meta-analyses do not provide consistent support for this theory. Very little attention has been paid to resolve and message factors on framing effects. What does this study add? Framed messages have an effect on exercise resolve, but not on intention. Loss-framed messages with attained outcomes are most persuasive for those who do not adhere to exercise guidelines. Exercise framing studies should include behavioural resolve next to intention. . © 2014 The British Psychological Society.

The impact of verbal framing on brain activity evoked by emotional images.

PubMed

Kisley, Michael A; Campbell, Alana M; Larson, Jenna M; Naftz, Andrea E; Regnier, Jesse T; Davalos, Deana B

2011-12-01

Emotional stimuli generally command more brain processing resources than non-emotional stimuli, but the magnitude of this effect is subject to voluntary control. Cognitive reappraisal represents one type of emotion regulation that can be voluntarily employed to modulate responses to emotional stimuli. Here, the late positive potential (LPP), a specific event-related brain potential (ERP) component, was measured in response to neutral, positive and negative images while participants performed an evaluative categorization task. One experimental group adopted a "negative frame" in which images were categorized as negative or not. The other adopted a "positive frame" in which the exact same images were categorized as positive or not. Behavioral performance confirmed compliance with random group assignment, and peak LPP amplitude to negative images was affected by group membership: brain responses to negative images were significantly reduced in the "positive frame" group. This suggests that adopting a more positive appraisal frame can modulate brain activity elicited by negative stimuli in the environment.

Positive emotional context eliminates the framing effect in decision-making.

PubMed

Cassotti, Mathieu; Habib, Marianne; Poirel, Nicolas; Aïte, Ania; Houdé, Olivier; Moutier, Sylvain

2012-10-01

Dual-process theories have suggested that emotion plays a key role in the framing effect in decision-making. However, little is known about the potential impact of a specific positive or negative emotional context on this bias. We investigated this question with adult participants using an emotional priming paradigm. First, participants were presented with positive or negative affective pictures (i.e., pleasant vs. unpleasant photographs). Afterward, participants had to perform a financial decision-making task that was unrelated to the pictures previously presented. The results revealed that the presentation framed in terms of gain or loss no longer affected subjects' decision-making following specific exposure to emotionally pleasant pictures. Interestingly, a positive emotional context did not globally influence risk-taking behavior but specifically decreased the risk propensity in the loss frame. This finding confirmed that a positive emotional context can reduce loss aversion, and it strongly reinforced the dual-process view that the framing effect stems from an affective heuristic belonging to intuitive System 1.

Automated Identification of the Heart Wall Throughout the Entire Cardiac Cycle Using Optimal Cardiac Phase for Extracted Features

NASA Astrophysics Data System (ADS)

Takahashi, Hiroki; Hasegawa, Hideyuki; Kanai, Hiroshi

2011-07-01

In most methods for evaluation of cardiac function based on echocardiography, the heart wall is currently identified manually by an operator. However, this task is very time-consuming and suffers from inter- and intraobserver variability. The present paper proposes a method that uses multiple features of ultrasonic echo signals for automated identification of the heart wall region throughout an entire cardiac cycle. In addition, the optimal cardiac phase to select a frame of interest, i.e., the frame for the initiation of tracking, was determined. The heart wall region at the frame of interest in this cardiac phase was identified by the expectation-maximization (EM) algorithm, and heart wall regions in the following frames were identified by tracking each point classified in the initial frame as the heart wall region using the phased tracking method. The results for two subjects indicate the feasibility of the proposed method in the longitudinal axis view of the heart.

Ballasted photovoltaic module and module arrays

DOEpatents

Botkin, Jonathan [El Cerrito, CA; Graves, Simon [Berkeley, CA; Danning, Matt [Oakland, CA

2011-11-29

A photovoltaic (PV) module assembly including a PV module and a ballast tray. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes an arm. The ballast tray is adapted for containing ballast and is removably associated with the PV module in a ballasting state where the tray is vertically under the PV laminate and vertically over the arm to impede overt displacement of the PV module. The PV module assembly can be installed to a flat commercial rooftop, with the PV module and the ballast tray both resting upon the rooftop. In some embodiments, the ballasting state includes corresponding surfaces of the arm and the tray being spaced from one another under normal (low or no wind) conditions, such that the frame is not continuously subjected to a weight of the tray.

Non-Contact Smartphone-Based Monitoring of Thermally Stressed Structures

PubMed Central

Ozturk, Turgut; Mas, David; Rizzo, Piervincenzo

2018-01-01

The in-situ measurement of thermal stress in beams or continuous welded rails may prevent structural anomalies such as buckling. This study proposed a non-contact monitoring/inspection approach based on the use of a smartphone and a computer vision algorithm to estimate the vibrating characteristics of beams subjected to thermal stress. It is hypothesized that the vibration of a beam can be captured using a smartphone operating at frame rates higher than conventional 30 Hz, and the first few natural frequencies of the beam can be extracted using a computer vision algorithm. In this study, the first mode of vibration was considered and compared to the information obtained with a conventional accelerometer attached to the two structures investigated, namely a thin beam and a thick beam. The results show excellent agreement between the conventional contact method and the non-contact sensing approach proposed here. In the future, these findings may be used to develop a monitoring/inspection smartphone application to assess the axial stress of slender structures, to predict the neutral temperature of continuous welded rails, or to prevent thermal buckling. PMID:29670034

Non-Contact Smartphone-Based Monitoring of Thermally Stressed Structures.

PubMed

Sefa Orak, Mehmet; Nasrollahi, Amir; Ozturk, Turgut; Mas, David; Ferrer, Belen; Rizzo, Piervincenzo

2018-04-18

The in-situ measurement of thermal stress in beams or continuous welded rails may prevent structural anomalies such as buckling. This study proposed a non-contact monitoring/inspection approach based on the use of a smartphone and a computer vision algorithm to estimate the vibrating characteristics of beams subjected to thermal stress. It is hypothesized that the vibration of a beam can be captured using a smartphone operating at frame rates higher than conventional 30 Hz, and the first few natural frequencies of the beam can be extracted using a computer vision algorithm. In this study, the first mode of vibration was considered and compared to the information obtained with a conventional accelerometer attached to the two structures investigated, namely a thin beam and a thick beam. The results show excellent agreement between the conventional contact method and the non-contact sensing approach proposed here. In the future, these findings may be used to develop a monitoring/inspection smartphone application to assess the axial stress of slender structures, to predict the neutral temperature of continuous welded rails, or to prevent thermal buckling.

75 FR 20792 - Airworthiness Directives; The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-21

... develop in the adjacent frame structure and skin, resulting in a rapid loss of cabin pressure. DATES: We... the following methods: Federal eRulemaking Portal: Go to http://www.regulations.gov . Follow the... severed, cracks could develop in the adjacent frame structure and skin, resulting in rapid loss of cabin...

Fabrication of the V-22 composite AFT fuselage using automated fiber placement

NASA Technical Reports Server (NTRS)

Pinckney, Robert L.

1991-01-01

Boeing Helicopters and its subcontractors are working together under an Air Force Wright Research and Development Center (WRDC)-Manufacturing-Technology Large-Composite Primary Structure Fuselage program to develop and demonstrate new manufacturing techniques for producing composite fuselage skin and frame structures. Three sets of aft fuselage skins and frames have been fabricated and assembled, and substantial reductions in fabrication and assembly costs demonstrated.

Framing life and death on YouTube: the strategic communication of organ donation messages by organ procurement organizations.

PubMed

VanderKnyff, Jeremy; Friedman, Daniela B; Tanner, Andrea

2015-01-01

Using a sample of YouTube videos posted on the YouTube channels of organ procurement organizations, a content analysis was conducted to identify the frames used to strategically communicate prodonation messages. A total of 377 videos were coded for general characteristics, format, speaker characteristics, organs discussed, structure, problem definition, and treatment. Principal components analysis identified message frames, and k-means cluster analysis established distinct groupings of videos on the basis of the strength of their relationship to message frames. Analysis of these frames and clusters found that organ procurement organizations present multiple, and sometimes competing, video types and message frames on YouTube. This study serves as important formative research that will inform future studies to measure the effectiveness of the distinct message frames and clusters identified.

Theory of equilibria of elastic 2-braids with interstrand interaction

NASA Astrophysics Data System (ADS)

Starostin, E. L.; van der Heijden, G. H. M.

2014-03-01

Motivated by continuum models for DNA supercoiling we formulate a theory for equilibria of 2-braids, i.e., structures formed by two elastic rods winding around each other in continuous contact and subject to a local interstrand interaction. No assumption is made on the shape of the contact curve. The theory is developed in terms of a moving frame of directors attached to one of the strands. The other strand is tracked by including in this frame the normalised closest-approach chord connecting the two strands. The kinematic constant-distance constraint is formulated at strain level through the introduction of what we call braid strains. As a result the total potential energy involves arclength derivatives of these strains, thus giving rise to a second-order variational problem. The Euler-Lagrange equations for this problem give balance equations for the overall braid force and moment referred to the moving frame as well as differential equations that can be interpreted as effective constitutive relations encoding the effect that the second strand has on the first as the braid deforms under the action of end loads. Hard contact models are used to obtain the normal contact pressure between strands that has to be non-negative for a physically realisable solution without the need for external devices such as clamps or glue to keep the strands together. The theory is first illustrated by a number of problems that can be solved analytically and then applied to several new problems that have not hitherto been treated.

Multiple enface image averaging for enhanced optical coherence tomography angiography imaging.

PubMed

Uji, Akihito; Balasubramanian, Siva; Lei, Jianqin; Baghdasaryan, Elmira; Al-Sheikh, Mayss; Borrelli, Enrico; Sadda, SriniVas R

2018-05-31

To investigate the effect of multiple enface image averaging on image quality of the optical coherence tomography angiography (OCTA). Twenty-one normal volunteers were enrolled in this study. For each subject, one eye was imaged with 3 × 3 mm scan protocol, and another eye was imaged with the 6 × 6 mm scan protocol centred on the fovea using the ZEISS Angioplex™ spectral-domain OCTA device. Eyes were repeatedly imaged to obtain nine OCTA cube scan sets, and nine superficial capillary plexus (SCP) and deep capillary plexus (DCP) were individually averaged after registration. Eighteen eyes with a 3 × 3 mm scan field and 14 eyes with a 6 × 6 mm scan field were studied. Averaged images showed more continuous vessels and less background noise in both the SCP and the DCP as the number of frames used for averaging increased, with both 3 × 3 and 6 × 6 mm scan protocols. The intensity histogram of the vessels dramatically changed after averaging. Contrast-to-noise ratio (CNR) and subjectively assessed image quality scores also increased as the number of frames used for averaging increased in all image types. However, the additional benefit in quality diminished when averaging more than five frames. Averaging only three frames achieved significant improvement in CNR and the score assigned by certified grades. Use of multiple image averaging in OCTA enface images was found to be both objectively and subjectively effective for enhancing image quality. These findings may of value for developing optimal OCTA imaging protocols for future studies. © 2018 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Controlling Surface Plasmons Through Covariant Transformation of the Spin-Dependent Geometric Phase Between Curved Metamaterials

NASA Astrophysics Data System (ADS)

Zhong, Fan; Li, Jensen; Liu, Hui; Zhu, Shining

2018-06-01

General relativity uses curved space-time to describe accelerating frames. The movement of particles in different curved space-times can be regarded as equivalent physical processes based on the covariant transformation between different frames. In this Letter, we use one-dimensional curved metamaterials to mimic accelerating particles in curved space-times. The different curved shapes of structures are used to mimic different accelerating frames. The different geometric phases along the structure are used to mimic different movements in the frame. Using the covariant principle of general relativity, we can obtain equivalent nanostructures based on space-time transformations, such as the Lorentz transformation and conformal transformation. In this way, many covariant structures can be found that produce the same surface plasmon fields when excited by spin photons. A new kind of accelerating beam, the Rindler beam, is obtained based on the Rindler metric in gravity. Very large effective indices can be obtained in such systems based on geometric-phase gradient. This general covariant design method can be extended to many other optical media.

Preliminary structural design of a lunar transfer vehicle aerobrake. M.S. Thesis

NASA Technical Reports Server (NTRS)

Bush, Lance B.

1992-01-01

An aerobrake concept for a Lunar transfer vehicle was weight optimized through the use of the Taguchi design method, structural finite element analyses and structural sizing routines. Six design parameters were chosen to represent the aerobrake structural configuration. The design parameters included honeycomb core thickness, diameter to depth ratio, shape, material, number of concentric ring frames, and number of radial frames. Each parameter was assigned three levels. The minimum weight aerobrake configuration resulting from the study was approx. half the weight of the average of all twenty seven experimental configurations. The parameters having the most significant impact on the aerobrake structural weight were identified.

Comparative study on diagonal equivalent methods of masonry infill panel

NASA Astrophysics Data System (ADS)

Amalia, Aniendhita Rizki; Iranata, Data

2017-06-01

Infrastructure construction in earthquake prone area needs good design process, including modeling a structure in a correct way to reduce damages caused by an earthquake. Earthquakes cause many damages e.g. collapsed buildings that are dangerous. An incorrect modeling in design process certainly affects the structure's ability in responding to load, i.e. an earthquake load, and it needs to be paid attention to in order to reduce damages and fatalities. A correct modeling considers every aspect that affects the strength of a building, including stiffness of resisting lateral loads caused by an earthquake. Most of structural analyses still use open frame method that does not consider the effect of stiffness of masonry panel to the stiffness and strength of the whole structure. Effect of masonry panel is usually not included in design process, but the presence of this panel greatly affects behavior of the building in responding to an earthquake. In worst case scenario, it can even cause the building to collapse as what has been reported after great earthquakes worldwide. Modeling a structure with masonry panel as consideration can be performed by designing the panel as compression brace or shell element. In designing masonry panel as a compression brace, there are fourteen methods popular to be used by structure designers formulated by Saneinejad-Hobbs, Holmes, Stafford-Smith, Mainstones, Mainstones-Weeks, Bazan-Meli, Liauw Kwan, Paulay and Priestley, FEMA 356, Durani Luo, Hendry, Al-Chaar, Papia and Chen-Iranata. Every method has its own equation and parameters to use, therefore the model of every method was compared to results of experimental test to see which one gives closer values. Moreover, those methods also need to be compared to the open frame to see if they can result values within limits. Experimental test that was used in comparing all methods was taken from Mehrabi's research (Fig. 1), which was a prototype of a frame in a structure with 0.5 scale and the ratio of height to width of 1 to 1.5. Load used in the experiment was based on Uniform Building Code (UBC) 1991. Every method compared was calculated first to get equivalent diagonal strut width. The second step was modelling method using structure analysis software as a frame with a diagonal in a linear mode. The linear mode was chosen based on structure analysis commonly used by structure designers. The frame was loaded and for every model, its load and deformation values were identified. The values of load - deformation of every method were compared to those of experimental test specimen by Mehrabi and open frame. From comparative study performed, Holmes' and Bazan-Meli's equations gave results the closest to the experimental test specimen by Mehrabi. Other equations that gave close values within the limit (by comparing it to the open frame) are Saneinejad-Hobbs, Stafford-Smith, Bazan-Meli, Liauw Kwan, Paulay and Priestley, FEMA 356, Durani Luo, Hendry, Papia and Chen-Iranata.

A prospective interrupted time series study of interventions to improve the quality, rating, framing and structure of goal-setting in community-based brain injury rehabilitation.

PubMed

Hassett, Leanne; Simpson, Grahame; Cotter, Rachel; Whiting, Diane; Hodgkinson, Adeline; Martin, Diane

2015-04-01

To investigate whether the introduction of an electronic goals system followed by staff training improved the quality, rating, framing and structure of goals written by a community-based brain injury rehabilitation team. Interrupted time series design. Two interventions were introduced six months apart. The first intervention comprised the introduction of an electronic goals system. The second intervention comprised a staff goal training workshop. An audit protocol was devised to evaluate the goals. A random selection of goal statements from the 12 months prior to the interventions (Time 1 baseline) were compared with all goal statements written after the introduction of the electronic goals system (Time 2) and staff training (Time 3). All goals were de-identified for client and time-period, and randomly ordered. A total of 745 goals (Time 1 n = 242; Time 2 n = 283; Time 3 n = 220) were evaluated. Compared with baseline, the introduction of the electronic goals system alone significantly increased goal rating, framing and structure (χ(2) tests 144.7, 18.9, 48.1, respectively, p < 0.001). The addition of staff training meant that the improvement in goal quality, which was only a trend at Time 2, was statistically significant at Time 3 (χ(2) 15.0, p ≤ 001). The training also led to a further significant increase in the framing and structuring of goals over the electronic goals system (χ(2) 11.5, 12.5, respectively, p ≤ 0.001). An electronic goals system combined with staff training improved the quality, rating, framing and structure of goal statements. © The Author(s) 2014.

Accuracy of frame-based stereotactic depth electrode implantation during craniotomy for subdural grid placement.

PubMed

Munyon, Charles N; Koubeissi, Mohamad Z; Syed, Tanvir U; Lüders, Hans O; Miller, Jonathan P

2013-01-01

Frame-based stereotaxy and open craniotomy may seem mutually exclusive, but invasive electrophysiological monitoring can require broad sampling of the cortex and precise targeting of deeper structures. The purpose of this study is to describe simultaneous frame-based insertion of depth electrodes and craniotomy for placement of subdural grids through a single surgical field and to determine the accuracy of depth electrodes placed using this technique. A total of 6 patients with intractable epilepsy underwent placement of a stereotactic frame with the center of the planned cranial flap equidistant from the fixation posts. After volumetric imaging, craniotomy for placement of subdural grids was performed. Depth electrodes were placed using frame-based stereotaxy. Postoperative CT determined the accuracy of electrode placement. A total of 31 depth electrodes were placed. Mean distance of distal electrode contact from the target was 1.0 ± 0.15 mm. Error was correlated to distance to target, with an additional 0.35 mm error for each centimeter (r = 0.635, p < 0.001); when corrected, there was no difference in accuracy based on target structure or method of placement (prior to craniotomy vs. through grid, p = 0.23). The described technique for craniotomy through a stereotactic frame allows placement of subdural grids and depth electrodes without sacrificing the accuracy of a frame or requiring staged procedures.

75 FR 11435 - Airworthiness Directives; Airbus Model A300 B4-2C, B4-103, and B4-203 Airplanes; and Model A300...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-11

... operator reported that, during a routine inspection, the Right Hand frame 40 forward fitting between... result in a deterioration of the structural integrity of the frame. * * * * * We are issuing this AD to... operator reported that, during a routine inspection, the Right Hand frame 40 forward fitting between...

Damage source identification of reinforced concrete structure using acoustic emission technique.

PubMed

Panjsetooni, Alireza; Bunnori, Norazura Muhamad; Vakili, Amir Hossein

2013-01-01

Acoustic emission (AE) technique is one of the nondestructive evaluation (NDE) techniques that have been considered as the prime candidate for structural health and damage monitoring in loaded structures. This technique was employed for investigation process of damage in reinforced concrete (RC) frame specimens. A number of reinforced concrete RC frames were tested under loading cycle and were simultaneously monitored using AE. The AE test data were analyzed using the AE source location analysis method. The results showed that AE technique is suitable to identify the sources location of damage in RC structures.

Damage Source Identification of Reinforced Concrete Structure Using Acoustic Emission Technique

PubMed Central

Panjsetooni, Alireza; Bunnori, Norazura Muhamad; Vakili, Amir Hossein

2013-01-01

Acoustic emission (AE) technique is one of the nondestructive evaluation (NDE) techniques that have been considered as the prime candidate for structural health and damage monitoring in loaded structures. This technique was employed for investigation process of damage in reinforced concrete (RC) frame specimens. A number of reinforced concrete RC frames were tested under loading cycle and were simultaneously monitored using AE. The AE test data were analyzed using the AE source location analysis method. The results showed that AE technique is suitable to identify the sources location of damage in RC structures. PMID:23997681

Practical low-cost visual communication using binary images for deaf sign language.

PubMed

Manoranjan, M D; Robinson, J A

2000-03-01

Deaf sign language transmitted by video requires a temporal resolution of 8 to 10 frames/s for effective communication. Conventional videoconferencing applications, when operated over low bandwidth telephone lines, provide very low temporal resolution of pictures, of the order of less than a frame per second, resulting in jerky movement of objects. This paper presents a practical solution for sign language communication, offering adequate temporal resolution of images using moving binary sketches or cartoons, implemented on standard personal computer hardware with low-cost cameras and communicating over telephone lines. To extract cartoon points an efficient feature extraction algorithm adaptive to the global statistics of the image is proposed. To improve the subjective quality of the binary images, irreversible preprocessing techniques, such as isolated point removal and predictive filtering, are used. A simple, efficient and fast recursive temporal prefiltering scheme, using histograms of successive frames, reduces the additive and multiplicative noise from low-cost cameras. An efficient three-dimensional (3-D) compression scheme codes the binary sketches. Subjective tests performed on the system confirm that it can be used for sign language communication over telephone lines.

Coupling Vanishing Point Tracking with Inertial Navigation to Estimate Attitude in a Structured Environment

DTIC Science & Technology

2011-03-01

with the Earth but does follow the Earth’s orbit around the sun . Though it is not a true inertial frame, for the sake of terrestrial navigation it can...the center of the Earth , with the x and y-axes on the equatorial plane and the z- axis along the Earth’s axis of rotation. The i-frame does not spin...be considered as such. Earth -centered Earth -fixed frame (e-frame) - The origin is fixed at the center of the Earth , with the x- axis on the equatorial

Key Frame Extraction in the Summary Space.

PubMed

Li, Xuelong; Zhao, Bin; Lu, Xiaoqiang; Xuelong Li; Bin Zhao; Xiaoqiang Lu; Lu, Xiaoqiang; Li, Xuelong; Zhao, Bin

2018-06-01

Key frame extraction is an efficient way to create the video summary which helps users obtain a quick comprehension of the video content. Generally, the key frames should be representative of the video content, meanwhile, diverse to reduce the redundancy. Based on the assumption that the video data are near a subspace of a high-dimensional space, a new approach, named as key frame extraction in the summary space, is proposed for key frame extraction in this paper. The proposed approach aims to find the representative frames of the video and filter out similar frames from the representative frame set. First of all, the video data are mapped to a high-dimensional space, named as summary space. Then, a new representation is learned for each frame by analyzing the intrinsic structure of the summary space. Specifically, the learned representation can reflect the representativeness of the frame, and is utilized to select representative frames. Next, the perceptual hash algorithm is employed to measure the similarity of representative frames. As a result, the key frame set is obtained after filtering out similar frames from the representative frame set. Finally, the video summary is constructed by assigning the key frames in temporal order. Additionally, the ground truth, created by filtering out similar frames from human-created summaries, is utilized to evaluate the quality of the video summary. Compared with several traditional approaches, the experimental results on 80 videos from two datasets indicate the superior performance of our approach.

A multistage motion vector processing method for motion-compensated frame interpolation.

PubMed

Huang, Ai- Mei; Nguyen, Truong Q

2008-05-01

In this paper, a novel, low-complexity motion vector processing algorithm at the decoder is proposed for motion-compensated frame interpolation or frame rate up-conversion. We address the problems of having broken edges and deformed structures in an interpolated frame by hierarchically refining motion vectors on different block sizes. Our method explicitly considers the reliability of each received motion vector and has the capability of preserving the structure information. This is achieved by analyzing the distribution of residual energies and effectively merging blocks that have unreliable motion vectors. The motion vector reliability information is also used as a prior knowledge in motion vector refinement using a constrained vector median filter to avoid choosing identical unreliable one. We also propose using chrominance information in our method. Experimental results show that the proposed scheme has better visual quality and is also robust, even in video sequences with complex scenes and fast motion.

Wavelet denoising of multiframe optical coherence tomography data

PubMed Central

Mayer, Markus A.; Borsdorf, Anja; Wagner, Martin; Hornegger, Joachim; Mardin, Christian Y.; Tornow, Ralf P.

2012-01-01

We introduce a novel speckle noise reduction algorithm for OCT images. Contrary to present approaches, the algorithm does not rely on simple averaging of multiple image frames or denoising on the final averaged image. Instead it uses wavelet decompositions of the single frames for a local noise and structure estimation. Based on this analysis, the wavelet detail coefficients are weighted, averaged and reconstructed. At a signal-to-noise gain at about 100% we observe only a minor sharpness decrease, as measured by a full-width-half-maximum reduction of 10.5%. While a similar signal-to-noise gain would require averaging of 29 frames, we achieve this result using only 8 frames as input to the algorithm. A possible application of the proposed algorithm is preprocessing in retinal structure segmentation algorithms, to allow a better differentiation between real tissue information and unwanted speckle noise. PMID:22435103

Wavelet denoising of multiframe optical coherence tomography data.

PubMed

Mayer, Markus A; Borsdorf, Anja; Wagner, Martin; Hornegger, Joachim; Mardin, Christian Y; Tornow, Ralf P

2012-03-01

We introduce a novel speckle noise reduction algorithm for OCT images. Contrary to present approaches, the algorithm does not rely on simple averaging of multiple image frames or denoising on the final averaged image. Instead it uses wavelet decompositions of the single frames for a local noise and structure estimation. Based on this analysis, the wavelet detail coefficients are weighted, averaged and reconstructed. At a signal-to-noise gain at about 100% we observe only a minor sharpness decrease, as measured by a full-width-half-maximum reduction of 10.5%. While a similar signal-to-noise gain would require averaging of 29 frames, we achieve this result using only 8 frames as input to the algorithm. A possible application of the proposed algorithm is preprocessing in retinal structure segmentation algorithms, to allow a better differentiation between real tissue information and unwanted speckle noise.

Nonlinear earthquake analysis of reinforced concrete frames with fiber and Bernoulli-Euler beam-column element.

PubMed

Karaton, Muhammet

2014-01-01

A beam-column element based on the Euler-Bernoulli beam theory is researched for nonlinear dynamic analysis of reinforced concrete (RC) structural element. Stiffness matrix of this element is obtained by using rigidity method. A solution technique that included nonlinear dynamic substructure procedure is developed for dynamic analyses of RC frames. A predicted-corrected form of the Bossak-α method is applied for dynamic integration scheme. A comparison of experimental data of a RC column element with numerical results, obtained from proposed solution technique, is studied for verification the numerical solutions. Furthermore, nonlinear cyclic analysis results of a portal reinforced concrete frame are achieved for comparing the proposed solution technique with Fibre element, based on flexibility method. However, seismic damage analyses of an 8-story RC frame structure with soft-story are investigated for cases of lumped/distributed mass and load. Damage region, propagation, and intensities according to both approaches are researched.

Rigidified pneumatic composites

NASA Astrophysics Data System (ADS)

van Dessel, Steven

2000-10-01

The overall objective of the research presented in this dissertation was to address global issues of adequate housing for all and the need for more sustainable human settlement. In order to address these, the emerging technology of rigidified pneumatic composites was investigated. Rigidified pneumatic composites (RPC) are defined as thin flexible membrane structures that are pneumatically deployed. After deployment, these structures harden due to chemical or physical change of the membrane. Because of this change, these structures do no longer require pneumatic pressure to maintain their shape. For the first time, a systematic listing of the various means available to develop polymeric materials useful in RPC technology is presented. With the aim to reduce the cost of RPC structures, a new material was proposed, developed, and evaluated. This material involved the formation of a semi-interpenetrating polymer network based on poly vinyl chloride and an acrylate based reactive plasticizer. The economical and environmental performances of RPC structures using this new material were assessed by means of a case study. In this study, the performance of RPC technology was compared with that of a typical wood light frame structure in the application of a small single-family house. The study indicated that the cost of ownership in present day value for the RPC structure was approximately 33% less than the cost of a comparable wood light frame structure. The study also indicated that significant environmental benefits exist with the use of RPC structures. It was found that the RPC structure used significantly less resources compared to the wood light frame structure. About 3.5 times less materials coming from non-renewable fossil resources, about 2.5 times less materials coming from trees, and about 19 times less materials coming from inorganic resources was used in the RPC structure relative to the wood light frame structure. The study concluded with pointing out various means available to further increase the economical and environmental performance of RPC technology. Directions were provided to guide future developments of RPC technology.

Modal nudging in nonlinear elasticity: Tailoring the elastic post-buckling behaviour of engineering structures

NASA Astrophysics Data System (ADS)

Cox, B. S.; Groh, R. M. J.; Avitabile, D.; Pirrera, A.

2018-07-01

The buckling and post-buckling behaviour of slender structures is increasingly being harnessed for smart functionalities. Equally, the post-buckling regime of many traditional engineering structures is not being used for design and may therefore harbour latent load-bearing capacity for further structural efficiency. Both applications can benefit from a robust means of modifying and controlling the post-buckling behaviour for a specific purpose. To this end, we introduce a structural design paradigm termed modal nudging, which can be used to tailor the post-buckling response of slender engineering structures without any significant increase in mass. Modal nudging uses deformation modes of stable post-buckled equilibria to perturb the undeformed baseline geometry of the structure imperceptibly, thereby favouring the seeded post-buckling response over potential alternatives. The benefits of this technique are enhanced control over the post-buckling behaviour, such as modal differentiation for smart structures that use snap-buckling for shape adaptation, or alternatively, increased load-carrying capacity, increased compliance or a shift from imperfection sensitivity to imperfection insensitivity. Although these concepts are, in theory, of general applicability, we concentrate here on planar frame structures analysed using the nonlinear finite element method and numerical continuation procedures. Using these computational techniques, we show that planar frame structures may exhibit isolated regions of stable equilibria in otherwise unstable post-buckling regimes, or indeed stable equilibria entirely disconnected from the natural structural response. In both cases, the load-carrying capacity of these isolated stable equilibria is greater than the natural structural response of the frames. Using the concept of modal nudging it is possible to "nudge" the frames onto these equilibrium paths of greater load-carrying capacity. Due to the scale invariance of modal nudging, these findings may impact the design of structures from the micro- to the macro-scale.

The Influence of Framing on Risky Decisions: A Meta-analysis.

PubMed

Kühberger

1998-07-01

In framing studies, logically equivalent choice situations are differently described and the resulting preferences are studied. A meta-analysis of framing effects is presented for risky choice problems which are framed either as gains or as losses. This evaluates the finding that highlighting the positive aspects of formally identical problems does lead to risk aversion and that highlighting their equivalent negative aspects does lead to risk seeking. Based on a data pool of 136 empirical papers that reported framing experiments with nearly 30,000 participants, we calculated 230 effect sizes. Results show that the overall framing effect between conditions is of small to moderate size and that profound differences exist between research designs. Potentially relevant characteristics were coded for each study. The most important characteristics were whether framing is manipulated by changing reference points or by manipulating outcome salience, and response mode (choice vs. rating/judgment). Further important characteristics were whether options differ qualitatively or quantitatively in risk, whether there is one or multiple risky events, whether framing is manipulated by gain/loss or by task-responsive wording, whether dependent variables are measured between- or within- subjects, and problem domains. Sample (students vs. target populations) and unit of analysis (individual vs. group) was not influential. It is concluded that framing is a reliable phenomenon, but that outcome salience manipulations, which constitute a considerable amount of work, have to be distinguished from reference point manipulations and that procedural features of experimental settings have a considerable effect on effect sizes in framing experiments. Copyright 1998 Academic Press.

How to aggregate health? Separability and the effect of framing.

PubMed

Turpcu, Adam; Bleichrodt, Han; Le, Quang A; Doctor, Jason N

2012-01-01

Unweighted summation or quality-adjusted life year (QALY) utilitarianism is the most common way to aggregate health benefits in a cost-effectiveness analysis. A key qualitative principle underlying QALY utilitarianism is separability: those individuals unaffected by a policy choice should not influence the policy choice. Separability also underlies several of the alternatives for QALY utilitarianism that have been proposed. To test separability and to test whether the support for separability is affected by the framing of the choice questions. In 2 experiments, 345 student subjects (162 in the first experiment, and 183 in the second experiment) were asked to select 1 of 2 possible treatments, with each treatment resulting in a different distribution of health across individuals. The only aspect that varied across choice questions was the state of the patients whose health was unaffected by the act of choosing a policy. In each experiment, we used 2 frames. In the implicit frame, it was implied but not plainly expressed what outcomes the treatments had in common. In the explicit frame, common outcomes of the 2 treatments were directly stated. The 2 experiments differed in the way the explicit frame was presented (verbal v. numerical). The support for separability was significantly greater in the explicit frame. The proportion of violations in the implicit frame was 44% in Experiment 1 and 31% in Experiment 2, while in the explicit frame, the proportion of violations was 28% in Experiment 1 and 8% in Experiment 2. Framing affected the support for separability, raising issues as to whether it is possible to achieve a canonical representation of social choices.

Correlation-based motion vector processing with adaptive interpolation scheme for motion-compensated frame interpolation.

PubMed

Huang, Ai-Mei; Nguyen, Truong

2009-04-01

In this paper, we address the problems of unreliable motion vectors that cause visual artifacts but cannot be detected by high residual energy or bidirectional prediction difference in motion-compensated frame interpolation. A correlation-based motion vector processing method is proposed to detect and correct those unreliable motion vectors by explicitly considering motion vector correlation in the motion vector reliability classification, motion vector correction, and frame interpolation stages. Since our method gradually corrects unreliable motion vectors based on their reliability, we can effectively discover the areas where no motion is reliable to be used, such as occlusions and deformed structures. We also propose an adaptive frame interpolation scheme for the occlusion areas based on the analysis of their surrounding motion distribution. As a result, the interpolated frames using the proposed scheme have clearer structure edges and ghost artifacts are also greatly reduced. Experimental results show that our interpolated results have better visual quality than other methods. In addition, the proposed scheme is robust even for those video sequences that contain multiple and fast motions.

An MR/MRI compatible core holder with the RF probe immersed in the confining fluid.

PubMed

Shakerian, M; Balcom, B J

2018-01-01

An open frame RF probe for high pressure and high temperature MR/MRI measurements was designed, fabricated, and tested. The open frame RF probe was installed inside an MR/MRI compatible metallic core holder, withstanding a maximum pressure and temperature of 5000 psi and 80 °C. The open frame RF probe was tunable for both 1 H and 19 F resonance frequencies with a 0.2 T static magnetic field. The open frame structure was based on simple pillars of PEEK polymer upon which the RF probe was wound. The RF probe was immersed in the high pressure confining fluid during operation. The open frame structure simplified fabrication of the RF probe and significantly reduced the amount of polymeric materials in the core holder. This minimized the MR background signal detected. Phase encoding MRI methods were employed to map the spin density of a sulfur hexafluoride gas saturating a Berea core plug in the core holder. The SF 6 was imaged as a high pressure gas and as a supercritical fluid. Copyright © 2017 Elsevier Inc. All rights reserved.

An MR/MRI compatible core holder with the RF probe immersed in the confining fluid

NASA Astrophysics Data System (ADS)

Shakerian, M.; Balcom, B. J.

2018-01-01

An open frame RF probe for high pressure and high temperature MR/MRI measurements was designed, fabricated, and tested. The open frame RF probe was installed inside an MR/MRI compatible metallic core holder, withstanding a maximum pressure and temperature of 5000 psi and 80 °C. The open frame RF probe was tunable for both 1H and 19F resonance frequencies with a 0.2 T static magnetic field. The open frame structure was based on simple pillars of PEEK polymer upon which the RF probe was wound. The RF probe was immersed in the high pressure confining fluid during operation. The open frame structure simplified fabrication of the RF probe and significantly reduced the amount of polymeric materials in the core holder. This minimized the MR background signal detected. Phase encoding MRI methods were employed to map the spin density of a sulfur hexafluoride gas saturating a Berea core plug in the core holder. The SF6 was imaged as a high pressure gas and as a supercritical fluid.

Multi-modal Brain MRI in Subjects with PD and iRBD.

PubMed

Mangia, Silvia; Svatkova, Alena; Mascali, Daniele; Nissi, Mikko J; Burton, Philip C; Bednarik, Petr; Auerbach, Edward J; Giove, Federico; Eberly, Lynn E; Howell, Michael J; Nestrasil, Igor; Tuite, Paul J; Michaeli, Shalom

2017-01-01

Idiopathic rapid eye movement sleep behavior disorder (iRBD) is a condition that often evolves into Parkinson's disease (PD). Therefore, by monitoring iRBD it is possible to track the neurodegeneration of individuals who may progress to PD. Here we aimed at piloting the characterization of brain tissue properties in mid-brain subcortical regions of 10 healthy subjects, 8 iRBD, and 9 early-diagnosed PD. We used a battery of magnetic resonance imaging (MRI) contrasts at 3 T, including adiabatic and non-adiabatic rotating frame techniques developed by our group, along with diffusion tensor imaging (DTI) and resting-state fMRI. Adiabatic T 1ρ and T 2ρ , and non-adiabatic RAFF4 (Relaxation Along a Fictitious Field in the rotating frame of rank 4) were found to have lower coefficient of variations and higher sensitivity to detect group differences as compared to DTI parameters such as fractional anisotropy and mean diffusivity. Significantly longer T 1ρ were observed in the amygdala of PD subjects vs. controls, along with a trend of lower functional connectivity as measured by regional homogeneity, thereby supporting the notion that amygdalar dysfunction occurs in PD. Significant abnormalities in reward networks occurred in iRBD subjects, who manifested lower network strength of the accumbens. In agreement with previous studies, significantly longer T 1ρ occurred in the substantia nigra compacta of PD vs. controls, indicative of neuronal degeneration, while regional homogeneity was lower in the substantia nigra reticulata. Finally, other trend-level findings were observed, i.e., lower RAFF4 and T 2ρ in the midbrain of iRBD subjects vs. controls, possibly indicating changes in non-motor features as opposed to motor function in the iRBD group. We conclude that rotating frame relaxation methods along with functional connectivity measures are valuable to characterize iRBD and PD subjects, and with proper validation in larger cohorts may provide pathological signatures of iRBD and PD.

Weighing in: the taste-engineering frame in obesity expert discourse.

PubMed

Ortiz, Selena E; Zimmerman, Frederick J; Gilliam, Franklin D

2015-03-01

We sought expert opinion on the problems with 2 dominant obesity-prevention discourse frames-personal responsibility and the environment-and examined alternative frames for understanding and addressing obesity. We conducted 60-minute, semistructured interviews with 15 US-based obesity experts. We manually coded and entered interview transcripts into software, generating themes and subthematic areas that captured the debate's essence. Although the environmental frame is the dominant model used in communications with the public and policymakers, several experts found that communicating key messages within this frame was difficult because of the enormity of the obesity problem. A subframe of the environmental frame--the taste-engineering frame--identifies food industry strategies to influence the overconsumption of certain foods and beverages. This emerging frame deconstructs the environmental frame so that causal attributes and responsible agents are more easily identifiable and proposed policies and public health interventions more salient. Expert interviews are an invaluable resource for understanding how experts use frames in discussing their work and in conversations with the public and policymakers. Future empirical studies testing the effectiveness of the taste-engineering frame on public opinion and support for structural-level health policies are needed.

Comprehensive Evaluation of Stand-Off Biometrics Techniques for Enhanced Surveillance during Major Events

DTIC Science & Technology

2011-02-01

transactions. Analysts used  frame  counts to  measure  the duration for which the Test Subject interacted with the iris recognition system camera, from the...44  Figure 20:  Frame  Extracted from HD CCTV Video...the eyes are located and used as a  frame  of reference. Once the eyes are  located, the face image can be rotated clockwise or counter‐clockwise to

Electrochemical cell structure and method of making the same

DOEpatents

Schick, Louis Andrew; Libby, Cara Suzanne; Bowen, John Henry; Bourgeois, Richard Scott

2012-09-25

An electrochemical cell structure is provided which includes an anode, a cathode spaced apart from said anode, an electrolyte in ionic communication with each of said anode and said cathode and a nonconductive frame. The nonconductive frame includes at least two components that support each of said anode, said cathode and said electrolyte and define at least one flowpath for working fluids and for products of electrochemical reaction.

Seismic response of 3D steel buildings considering the effect of PR connections and gravity frames.

PubMed

Reyes-Salazar, Alfredo; Bojórquez, Edén; Haldar, Achintya; López-Barraza, Arturo; Rivera-Salas, J Luz

2014-01-01

The nonlinear seismic responses of 3D steel buildings with perimeter moment resisting frames (PMRF) and interior gravity frames (IGF) are studied explicitly considering the contribution of the IGF. The effect on the structural response of the stiffness of the beam-to-column connections of the IGF, which is usually neglected, is also studied. It is commonly believed that the flexibility of shear connections is negligible and that 2D models can be used to properly represent 3D real structures. The results of the study indicate, however, that the moments developed on columns of IGF can be considerable and that modeling buildings as plane frames may result in very conservative designs. The contribution of IGF to the lateral structural resistance may be significant. The contribution increases when their connections are assumed to be partially restrained (PR). The incremented participation of IGF when the stiffness of their connections is considered helps to counteract the no conservative effect that results in practice when lateral seismic loads are not considered in IGF while designing steel buildings with PMRF. Thus, if the structural system under consideration is used, the three-dimensional model should be used in seismic analysis and the IGF and the stiffness of their connections should be considered as part of the lateral resistance system.

High But Not Low Probability of Gain Elicits a Positive Feeling Leading to the Framing Effect.

PubMed

Gosling, Corentin J; Moutier, Sylvain

2017-01-01

Human risky decision-making is known to be highly susceptible to profit-motivated responses elicited by the way in which options are framed. In fact, studies investigating the framing effect have shown that the choice between sure and risky options depends on how these options are presented. Interestingly, the probability of gain of the risky option has been highlighted as one of the main factors causing variations in susceptibility to the framing effect. However, while it has been shown that high probabilities of gain of the risky option systematically lead to framing bias, questions remain about the influence of low probabilities of gain. Therefore, the first aim of this paper was to clarify the respective roles of high and low probabilities of gain in the framing effect. Due to the difference between studies using a within- or between-subjects design, we conducted a first study investigating the respective roles of these designs. For both designs, we showed that trials with a high probability of gain led to the framing effect whereas those with a low probability did not. Second, as emotions are known to play a key role in the framing effect, we sought to determine whether they are responsible for such a debiasing effect of the low probability of gain. Our second study thus investigated the relationship between emotion and the framing effect depending on high and low probabilities. Our results revealed that positive emotion was related to risk-seeking in the loss frame, but only for trials with a high probability of gain. Taken together, these results support the interpretation that low probabilities of gain suppress the framing effect because they prevent the positive emotion of gain anticipation.

High But Not Low Probability of Gain Elicits a Positive Feeling Leading to the Framing Effect

PubMed Central

Gosling, Corentin J.; Moutier, Sylvain

2017-01-01

Human risky decision-making is known to be highly susceptible to profit-motivated responses elicited by the way in which options are framed. In fact, studies investigating the framing effect have shown that the choice between sure and risky options depends on how these options are presented. Interestingly, the probability of gain of the risky option has been highlighted as one of the main factors causing variations in susceptibility to the framing effect. However, while it has been shown that high probabilities of gain of the risky option systematically lead to framing bias, questions remain about the influence of low probabilities of gain. Therefore, the first aim of this paper was to clarify the respective roles of high and low probabilities of gain in the framing effect. Due to the difference between studies using a within- or between-subjects design, we conducted a first study investigating the respective roles of these designs. For both designs, we showed that trials with a high probability of gain led to the framing effect whereas those with a low probability did not. Second, as emotions are known to play a key role in the framing effect, we sought to determine whether they are responsible for such a debiasing effect of the low probability of gain. Our second study thus investigated the relationship between emotion and the framing effect depending on high and low probabilities. Our results revealed that positive emotion was related to risk-seeking in the loss frame, but only for trials with a high probability of gain. Taken together, these results support the interpretation that low probabilities of gain suppress the framing effect because they prevent the positive emotion of gain anticipation. PMID:28232808

Framing Options as Choice or Opportunity: Does the Frame Influence Decisions?

PubMed

Abhyankar, Purva; Summers, Barbara A; Velikova, Galina; Bekker, Hilary L

2014-07-01

Health professionals must enable patients to make informed decisions about health care choices through unbiased presentation of all options. This study examined whether presenting the decision as "opportunity" rather than "choice" biased individuals' preferences in the context of trial participation for cancer treatment. Self-selecting healthy women (N = 124) were randomly assigned to the following decision frames: opportunity to take part in the trial (opt-in), opportunity to be removed from the trial (opt-out), and choice to have standard treatment or take part in the trial (choice). The computer-based task required women to make a hypothetical choice about a real-world cancer treatment trial. The software presented the framed scenario, recorded initial preference, presented comprehensive and balanced information, traced participants' use of information during decision making, and recorded final decision. A posttask paper questionnaire assessed perceived risk, attitudes, subjective norm, perceived behavioral control, and satisfaction with decision. Framing influenced women's immediate preferences. Opportunity frames, whether opt-in or opt-out, introduced a bias as they discouraged women from choosing standard treatment. Using the choice frame avoided this bias. The opt-out opportunity frame also affected women's perceived social norm; women felt that others endorsed the trial option. The framing bias was not present once participants had had the opportunity to view detailed information on the options within a patient decision aid format. There were no group differences in information acquisition and final decisions. Sixteen percent changed their initial preference after receiving full information. A "choice" frame, where all treatment options are explicit, is less likely to bias preferences. Presentation of full information in parallel, option-by-attribute format is likely to "de-bias" the decision frame. Tailoring of information to initial preferences would be ill-advised as preferences may change following detailed information. © The Author(s) 2014.

Effects of the frame acquisition rate on the sensitivity of gastro-oesophageal reflux scintigraphy

PubMed Central

Codreanu, I; Chamroonrat, W; Edwards, K

2013-01-01

Objective: To compare the sensitivity of gastro-oesophageal reflux (GOR) scintigraphy at 5-s and 60-s frame acquisition rates. Methods: GOR scintigraphy of 50 subjects (1 month–20 years old, mean 42 months) were analysed concurrently using 5-s and 60-s acquisition frames. Reflux episodes were graded as low if activity was detected in the distal half of the oesophagus and high if activity was detected in its upper half or in the oral cavity. For comparison purposes, detected GOR in any number of 5-s frames corresponding to one 60-s frame was counted as one episode. Results: A total of 679 episodes of GOR to the upper oesophagus were counted using a 5-s acquisition technique. Only 183 of such episodes were detected on 60-s acquisition images. To the lower oesophagus, a total of 1749 GOR episodes were detected using a 5-s acquisition technique and only 1045 episodes using 60-s acquisition frames (these also included the high-level GOR on 5-s frames counted as low level on 60-s acquisition frames). 10 patients had high-level GOR episodes that were detected only using a 5-s acquisition technique, leading to a different diagnosis in these patients. No correlation between the number of reflux episodes and the gastric emptying rates was noted. Conclusion: The 5-s frame acquisition technique is more sensitive than the 60-s frame acquisition technique for detecting both high- and low-level GOR. Advances in knowledge: Brief GOR episodes with a relatively low number of radioactive counts are frequently indistinguishable from intense background activity on 60-s acquisition frames. PMID:23520226

"Can you see me now?" An objective metric for predicting intelligibility of compressed American Sign Language video

NASA Astrophysics Data System (ADS)

Ciaramello, Francis M.; Hemami, Sheila S.

2007-02-01

For members of the Deaf Community in the United States, current communication tools include TTY/TTD services, video relay services, and text-based communication. With the growth of cellular technology, mobile sign language conversations are becoming a possibility. Proper coding techniques must be employed to compress American Sign Language (ASL) video for low-rate transmission while maintaining the quality of the conversation. In order to evaluate these techniques, an appropriate quality metric is needed. This paper demonstrates that traditional video quality metrics, such as PSNR, fail to predict subjective intelligibility scores. By considering the unique structure of ASL video, an appropriate objective metric is developed. Face and hand segmentation is performed using skin-color detection techniques. The distortions in the face and hand regions are optimally weighted and pooled across all frames to create an objective intelligibility score for a distorted sequence. The objective intelligibility metric performs significantly better than PSNR in terms of correlation with subjective responses.

Optimization of Transmit Parameters in Cardiac Strain Imaging With Full and Partial Aperture Coherent Compounding.

PubMed

Sayseng, Vincent; Grondin, Julien; Konofagou, Elisa E

2018-05-01

Coherent compounding methods using the full or partial transmit aperture have been investigated as a possible means of increasing strain measurement accuracy in cardiac strain imaging; however, the optimal transmit parameters in either compounding approach have yet to be determined. The relationship between strain estimation accuracy and transmit parameters-specifically the subaperture, angular aperture, tilt angle, number of virtual sources, and frame rate-in partial aperture (subaperture compounding) and full aperture (steered compounding) fundamental mode cardiac imaging was thus investigated and compared. Field II simulation of a 3-D cylindrical annulus undergoing deformation and twist was developed to evaluate accuracy of 2-D strain estimation in cross-sectional views. The tradeoff between frame rate and number of virtual sources was then investigated via transthoracic imaging in the parasternal short-axis view of five healthy human subjects, using the strain filter to quantify estimation precision. Finally, the optimized subaperture compounding sequence (25-element subperture, 90° angular aperture, 10 virtual sources, 300-Hz frame rate) was compared to the optimized steered compounding sequence (60° angular aperture, 15° tilt, 10 virtual sources, 300-Hz frame rate) via transthoracic imaging of five healthy subjects. Both approaches were determined to estimate cumulative radial strain with statistically equivalent precision (subaperture compounding E(SNRe %) = 3.56, and steered compounding E(SNRe %) = 4.26).

The attitude-behavior discrepancy in medical decision making.

PubMed

He, Fei; Li, Dongdong; Cao, Rong; Zeng, Juli; Guan, Hao

2014-12-01

In medical practice, the dissatisfaction of patients about medical decisions made by doctors is often regarded as the fuse of doctor-patient conflict. However, a few studies have looked at why there are such dissatisfactions. This experimental study aimed to explore the discrepancy between attitude and behavior within medical situations and its interaction with framing description. A total of 450 clinical undergraduates were randomly assigned to six groups and investigated using the classic medical decision making problem, which was described either in a positive or a negative frame (2) × decision making behavior\\attitude to risky plan\\attitude to conservative plan (3). A discrepancy between attitude and behavior did exist in medical situations. Regarding medical dilemmas, if the mortality rate was described, subjects had a significant tendency to choose a conservative plan (t = 3.55, P < 0.01) yet if the survival rate was described, there was no such preference (t = -1.48, P > 0.05). However, regardless of the plan chosen by the doctor, the subjects had a significant opposing attitude (P < .05). Framing description had a significant impact on both decision making behavior and attitude (t behavior = -3.24, P < 0.01；t attitude to surgery = 4.08，P < 0.01；t attitude to radiation = -2.15，P < 0.05). A discrepancy of attitude-behavior does exist in medical situations. The framing of a description has an impact on medical decision-making.

A transform from absorption to Raman excitation profile. A time-dependent approach

NASA Astrophysics Data System (ADS)

Lee, Soo-Y.; Yeo, Robert C. K.

1994-04-01

An alternative time-frame approach, which is canonically conjugate to the energy-frame approach, for implementing the transform relations for calculating Raman excitation profiles directly from the optical absorption spectrum is presented. Practical and efficient fast Fourier transformation in the time frame replaces the widely used Chan and Page algorithm for evaluating the Hilbert transform in the energy frame. The time-frame approach is applied to: (a) a two-mode model which illustrates the missing mode effect in both absorption and Raman excitation profiles, (b) carotene, in which both the absorption spectrum and the Raman excitation profile show vibrational structure and (c) hexamethylbenzene: TCNE electron donor—acceptor complex where the same spectra are structureless and the Raman excitation profile for the 168 cm -1 mode poses a problem for the energy-frame approach. A similar time-frame approach can be used for the inverse transform from the Raman excitation profile to the optical absorption spectrum.

View of parking (resting) frame that supported the Shuttle assembly ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of parking (resting) frame that supported the Shuttle assembly when the hydrodynamic supports were not engaged (removed from structure). - Marshall Space Flight Center, Saturn V Dynamic Test Facility, East Test Area, Huntsville, Madison County, AL

View northwest, wharf B, timber framing, detail of cross bracing, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View northwest, wharf B, timber framing, detail of cross bracing, charred piers, recent galvanized fastenings - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

Dynamic measurement of the corneal tear film with a Twyman-Green interferometer

NASA Astrophysics Data System (ADS)

Micali, Jason D.; Greivenkamp, John E.; Primeau, Brian C.

2014-07-01

An interferometer for measuring dynamic properties of the in vivo tear film on the human cornea has been developed. The system is a near-infrared instantaneous phase-shifting Twyman-Green interferometer. The laser source is a 785 nm solidstate laser; the system has been carefully designed and calibrated to ensure that the system operates at eye safe levels. Measurements are made over a 6 mm diameter on the cornea. Successive frames of interferometric height measurements are combined to produce movies showing both the quantitative and qualitative changes in the topography of the tear film surface and structure. To date, measurement periods of up to 120 seconds at 28.6 frames per second have been obtained. Several human subjects have been examined using this system, demonstrating a surface height resolution of 25 nm and spatial resolution of 6 μm. Examples of features that have been observed in these in preliminary studies of the tear film include: post-blink disruption, evolution, and stabilization of the tear film; tear film artifacts generated by blinking; tear film evaporation and break-up; and the propagation of foreign objects in the tear film. This paper discusses the interferometer design and presents results from in vivo measurements.

Dynamic measurement of the corneal tear film with a Twyman-Green interferometer

NASA Astrophysics Data System (ADS)

Micali, Jason D.; Greivenkamp, John E.; Primeau, Brian C.

2015-05-01

An interferometer for measuring dynamic properties of the in vivo tear film on the human cornea has been developed. The system is a near-infrared instantaneous phase-shifting Twyman-Green interferometer. The laser source is a 785 nm solid-state laser, and the system has been carefully designed and calibrated to ensure that the system operates at eye-safe levels. Measurements are made over a 6 mm diameter on the cornea. Successive frames of interferometric height measurements are combined to produce movies showing both the quantitative and qualitative changes in the topography of the tear film surface and structure. To date, measurement periods of up to 120 s at 28.6 frames per second have been obtained. Several human subjects have been examined using this system, demonstrating a surface height resolution of 25 nm and spatial resolution of 6 μm. Examples of features that have been observed in these preliminary studies of the tear film include postblink disruption, evolution, and stabilization of the tear film; tear film artifacts generated by blinking; tear film evaporation and breakup; and the propagation of foreign objects in the tear film. This paper discusses the interferometer design and presents results from in vivo measurements.

The response of dense dry granular material to the shear reversal

NASA Astrophysics Data System (ADS)

Zhang, Jie; Ren, Jie; Farhadi, Somayeh; Behringer, Robert

2008-11-01

We have performed two dimensional granular experiments under pure shear using bidisperse photo-elastic disks. Starting from a stress free state, a square box filled with granular particles is subject to shear. The forward shears involved various number of steps, leading to maximum strains between 0.1 and 0.3. The area is kept constant during the shear. The network of force chains gradually built up as the strain increased, leading to increased pressure and shear stress. Reverse shear was then applied to the system. Depending on the initial packing fraction and the strain at which the shear is reversed, the force chain network built prior to the shear reversal may be destroyed completely or partially destroyed. Following the force chain weakening, when the reserve shear is continuously applied to the system, there is a force chain strengthening. Following each change of the system, contact forces of individual disks were measured by applying an inverse algorithm. We also kept track of the displacement and angle of rotation of every particle from frame to frame. We present the results for the structure failure and reconstruction during shear reversals. We also present data for stresses, contact force distributions and other statistical measures.

Investigation of the asymptotic state of rotating turbulence using large-eddy simulation

NASA Technical Reports Server (NTRS)

Squires, Kyle D.; Chasnov, Jeffrey R.; Mansour, Nagi N.; Cambon, Claude

1993-01-01

Study of turbulent flows in rotating reference frames has long been an area of considerable scientific and engineering interest. Because of its importance, the subject of turbulence in rotating reference frames has motivated over the years a large number of theoretical, experimental, and computational studies. The bulk of these previous works has served to demonstrate that the effect of system rotation on turbulence is subtle and remains exceedingly difficult to predict. A rotating flow of particular interest in many studies, including the present work, is examination of the effect of solid-body rotation on an initially isotropic turbulent flow. One of the principal reasons for the interest in this flow is that it represents the most basic turbulent flow whose structure is altered by system rotation but without the complicating effects introduced by mean strains or flow inhomogeneities. The assumption of statistical homogeneity considerably simplifies analysis and computation. The principal objective of the present study has been to examine the asymptotic state of solid-body rotation applied to an initially isotropic, high Reynolds number turbulent flow. Of particular interest has been to determine the degree of two-dimensionalization and the existence of asymptotic self-similar states in homogeneous rotating turbulence.

Evolution of vitamin B2 biosynthesis: structural and functional similarity between pyrimidine deaminases of eubacterial and plant origin.

PubMed

Fischer, Markus; Römisch, Werner; Saller, Sabine; Illarionov, Boris; Richter, Gerald; Rohdich, Felix; Eisenreich, Wolfgang; Bacher, Adelbert

2004-08-27

The Arabidopsis thaliana open reading frame At4g20960 predicts a protein whose N-terminal part is similar to the eubacterial 2,5-diamino-6-ribosylamino-4(3H)-pyrimidinone 5'-phosphate deaminase domain. A synthetic open reading frame specifying a pseudomature form of the plant enzyme directed the synthesis of a recombinant protein which was purified to apparent homogeneity and was shown by NMR spectroscopy to convert 2,5-diamino-6-ribosylamino-4(3H)-pyrimidinone 5'-phosphate into 5-amino-6-ribosylamino-2,4(1H,3H)-pyrimidinedione 5'-phosphate at a rate of 0.9 micromol mg(-1) min(-1). The substrate and product of the enzyme are both subject to spontaneous anomerization of the ribosyl side chain as shown by (13)C NMR spectroscopy. The protein contains 1 eq of Zn(2+)/subunit. The deaminase activity could be assigned to the N-terminal section of the plant protein. The deaminase domains of plants and eubacteria share a high degree of similarity, in contrast to deaminases from fungi. These data show that the riboflavin biosynthesis in plants proceeds by the same reaction steps as in eubacteria, whereas fungi use a different pathway.

Strength analysis and lightweight research of a fertilizing and soil covering vehicle

NASA Astrophysics Data System (ADS)

Sun, Heng-Hui; Zhang, Zheng-Yong; Liu, Yang; Xu, Hai-Ming; Chen, En-Wei

2018-03-01

In this paper, parametric modeling is carried out for the frame part of a kind of fertilizing and soil covering vehicle to define boundary conditions such as load, constraint, etc. when the frame is under the working condition of normal full load. ANSYS software is used to produce finite element model of frame, and to analyze and solve the model, so as to obtain stress and stain variation diagram of each part of frame under working condition of normal full load. The calculation result shows that: the structure of frame is able to meet the strength requirement, and the maximum value of stress is located at joint between frame and external hinge, which should be appropriately improved in thickening way. According to the result of finite element, the scheme with size optimization is employed to design the frame in lightweight way. The research result of this paper provides the theoretical basis for the design of frame of fertilizing and soil covering vehicle, which has deep theoretical significance and application value.

Study on the frame body structure of micro-electric vehicle based on frontal crash safety

NASA Astrophysics Data System (ADS)

Lu, Yaoquan; Zhang, Sanchuan

2017-08-01

In order to research the safety of skeleton type body of micro-electric vehicles in the frontal collision, the method of finite element modeling and simulation are used to analyze frame body that is fitted with the energy absorption structure, the simulation results show that On the basis of absorbing the most energy and the least of body acceleration, the absorbent structure parameters can be optimized, the optimized parameters are length 180 mm, wall thickness 3 mm and materials Q460.

Analysis of truss, beam, frame, and membrane components. [composite structures

NASA Technical Reports Server (NTRS)

Knoell, A. C.; Robinson, E. Y.

1975-01-01

Truss components are considered, taking into account composite truss structures, truss analysis, column members, and truss joints. Beam components are discussed, giving attention to composite beams, laminated beams, and sandwich beams. Composite frame components and composite membrane components are examined. A description is given of examples of flat membrane components and examples of curved membrane elements. It is pointed out that composite structural design and analysis is a highly interactive, iterative procedure which does not lend itself readily to characterization by design or analysis function only.-

Persuasiveness of online flu-vaccination promotional banners.

PubMed

Chien, Yu-Hung

2013-04-01

Young people appear to have relatively little motivation to participate in flu-vaccination programs. This study assessed the effectiveness of online banners in efforts to persuade young people to get vaccinated. Specifically, a 2 x 3 between-subjects factorial design was used to examine the effects of message framing (gain vs loss) and color configuration (white text on a red background, black text on a yellow background, and white text on a blue background) on 180 college students' perceptions of the persuasiveness of flu-vaccination promotional banners. Each participant completed a four-item questionnaire, and the results of an analysis of variance showed that persuasiveness scores were higher among participants exposed to a loss-framed than to a gain-framed message, but only when the loss-framed message was presented in white text on a red background. The theoretical and practical implications of manipulating these two factors in the development of effective health-promotion materials are discussed.

Framing tobacco control efforts within an ethical context

PubMed Central

Fox, B

2005-01-01

Public health efforts to promote tobacco control are not performed within a vacuum. They are subject to interpretation and misinterpretation by consumers and policymakers based largely upon the initial framing of the issues. This paper notes how the tobacco industry has established a particular frame that it is the protector of individual rights and that the public health community is trying to eliminate those rights. This paper then shows how the public health community uses metaphors that may unintentionally support this framing and suggests that by reframing public health efforts in accordance with core ethical principles, the public health community can create more positive messages. A public health ethical framework is proposed to examine how the application of the principles can influence the tobacco control movement. Through the increased use of ethics in tobacco control, the public health community may be better positioned to claim the high road as the protector of the public's interests. PMID:16046701

[Effects of frame of reference on the judgments of whole-body vibration intensity].

PubMed

Suzuki, H

1997-02-01

Although the concept of the term 'riding comfort' is ambiguous, in the present paper it means a perceptual experience derived from the vibrational factors of a running railway vehicle. When we regard riding comfort evaluation as a perceptual judgment process, we must consider that what is perceived is dependent not only on the physical properties of the stimuli, but also on the frame of reference. The purpose of the present study is to examine the effect of the frame on the judgments of vibration intensity in the anchoring effect paradigm. Using the four-axis vibration apparatus, we conducted experiments for eighty subjects, in which frequencies and lateral accelerations of vibrations were changed. As the result, we found a clear anchoring effect. This suggests that we must take into consideration effects of frame of reference in terms of riding comfort criterion of railway vehicles.

Breaking bad news: Effects of forecasting diagnosis and framing prognosis.

PubMed

Porensky, Emily K; Carpenter, Brian D

2016-01-01

Research to support guidelines for breaking bad news is lacking. This study used an experimental paradigm to test two communication strategies, forecasting bad news and framing prognosis, in the context of cancer. In a 2×2 design, 128 participants received bad news in a hypothetical consultation. A videotaped physician presented diagnostic and prognostic information, varying warning (warning shot vs. no warning), and framing (positive vs. negative). Effects on psychological distress, recall accuracy, and subjective interpretations of the news were assessed. Warning was not associated with lower psychological distress or improved recall. Individuals who heard a positively-framed prognosis had significantly less psychological distress, rated their prognosis better, and were more hopeful than those who heard a negatively-framed prognosis. However, they also showed a trend toward reduced accuracy in recalling prognostic statistics. Results contribute to a growing body of literature exploring optimal approaches for communicating bad news in health care. Although research in clinical settings is needed to bolster results, findings suggest that when providers use positive framing to reduce distress about prognosis, they should also consider ways to overcome potential reductions in recall accuracy, such as repeating statistical information or supplementing with written information. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

The Importance of 'Likes': The Interplay of Message Framing, Source, and Social Endorsement on Credibility Perceptions of Health Information on Facebook.

PubMed

Borah, Porismita; Xiao, Xizhu

2018-01-01

Online sources not only permeate the information-seeking environment of the younger generation, but also have profound influence in shaping their beliefs and behaviors. In this landscape, examining the factors responsible for credibility perceptions of online information is fundamental, particularly for health-related information. Using a 2 (frames: gain vs. loss) × 2 (source: expert vs. non-expert) × 2 (social endorsement: high vs. low) randomized between-subjects experimental design, this study examines the effect of health message framing and the moderating effects of social endorsement and source type on credibility perceptions of Facebook posts. Testing across two issues--physical activity and alcohol consumption--findings indicate that the gain-framed message was perceived as most credible. Additionally, significant three-way interactions suggest that social endorsement and source type affect the relationship between message framing and credibility perceptions. Specifically, the findings demonstrate that a gain-framed message from an expert source with high number of 'likes' is considered the most credible message. These findings have significant implications for information gathering from social media sources, such as the influence of 'likes' on health information.

Toward interventions to address moral distress: navigating structure and agency.

PubMed

Musto, Lynn C; Rodney, Patricia A; Vanderheide, Rebecca

2015-02-01

The concept of moral distress has been the subject of nursing research for the past 30 years. Recently, there has been a call to move from developing an understanding of the concept to developing interventions to help ameliorate the experience. At the same time, the use of the term moral distress has been critiqued for a lack of clarity about the concepts that underpin the experience. Some researchers suggest that a closer examination of how socio-political structures influence healthcare delivery will move moral distress from being seen as located in the individual to an experience that is also located in broader healthcare structures. Informed by new thinking in relational ethics, we draw on research findings from neuroscience and attachment literature to examine the reciprocal relationship between structures and agents and frame the experience of moral distress. We posit moral distress as a form of relational trauma and subsequently point to the need to better understand how nurses as moral agents are influenced by-and influence-the complex socio-political structures they inhabit. In so doing, we identify this reciprocity as a framework for interventions. © The Author(s) 2014.

Celestial reference frames and the gauge freedom in the post-Newtonian mechanics of the Earth-Moon system

NASA Astrophysics Data System (ADS)

Kopeikin, Sergei; Xie, Yi

2010-11-01

We introduce the Jacobi coordinates adopted to the advanced theoretical analysis of the relativistic Celestial Mechanics of the Earth-Moon system. Theoretical derivation utilizes the relativistic resolutions on reference frames adopted by the International Astronomical Union (IAU) in 2000. The resolutions assume that the Solar System is isolated and space-time is asymptotically flat at infinity and the primary reference frame covers the entire space-time, has its origin at the Solar System barycenter (SSB) with spatial axes stretching up to infinity. The SSB frame is not rotating with respect to a set of distant quasars that are assumed to be at rest on the sky forming the International Celestial Reference Frame (ICRF). The second reference frame has its origin at the Earth-Moon barycenter (EMB). The EMB frame is locally inertial and is not rotating dynamically in the sense that equation of motion of a test particle moving with respect to the EMB frame, does not contain the Coriolis and centripetal forces. Two other local frames—geocentric and selenocentric—have their origins at the center of mass of Earth and Moon respectively and do not rotate dynamically. Each local frame is subject to the geodetic precession both with respect to other local frames and with respect to the ICRF because of their relative motion with respect to each other. Theoretical advantage of the dynamically non-rotating local frames is in a more simple mathematical description of the metric tensor and relative equations of motion of the Moon with respect to Earth. Each local frame can be converted to kinematically non-rotating one after alignment with the axes of ICRF by applying the matrix of the relativistic precession as recommended by the IAU resolutions. The set of one global and three local frames is introduced in order to decouple physical effects of gravity from the gauge-dependent effects in the equations of relative motion of the Moon with respect to Earth.

[The framing effect: medical implications].

PubMed

Mazzocco, Ketti; Cherubini, Paolo; Rumiati, Rino

2005-01-01

Over the last 20 years, many studies explored how the way information is presented modifies choices. This sort of effect, referred to as "framing effects", typically consists of the inversion of choices when presenting structurally identical decision problems in different ways. It is a common assumption that physicians are unaffected (or less affected) by the surface description of a decision problem, because they are formally trained in medical decision making. However, several studies showed that framing effects occur even in the medical field. The complexity and variability of these effects are remarkable, making it necessary to distinguish among different framing effects, depending on whether the effect is obtained by modifying adjectives (attribute framing), goals of a behavior (goal framing), or the probability of an outcome (risky choice framing). A further reason for the high variability of the framing effects seems to be the domain of the decision problem, with different effects occurring in prevention decisions, disease-detection decisions, and treatment decisions. The present work reviews the studies on framing effects, in order to summarize them and clarify their possible role in medical decision making.

Smooth affine shear tight frames: digitization and applications

NASA Astrophysics Data System (ADS)

Zhuang, Xiaosheng

2015-08-01

In this paper, we mainly discuss one of the recent developed directional multiscale representation systems: smooth affine shear tight frames. A directional wavelet tight frame is generated by isotropic dilations and translations of directional wavelet generators, while an affine shear tight frame is generated by anisotropic dilations, shears, and translations of shearlet generators. These two tight frames are actually connected in the sense that the affine shear tight frame can be obtained from a directional wavelet tight frame through subsampling. Consequently, an affine shear tight frame indeed has an underlying filter bank from the MRA structure of its associated directional wavelet tight frame. We call such filter banks affine shear filter banks, which can be designed completely in the frequency domain. We discuss the digitization of affine shear filter banks and their implementations: the forward and backward digital affine shear transforms. Redundancy rate and computational complexity of digital affine shear transforms are also investigated in this paper. Numerical experiments and comparisons in image/video processing show the advantages of digital affine shear transforms over many other state-of-art directional multiscale representation systems.

Real Time Apnoea Monitoring of Children Using the Microsoft Kinect Sensor: A Pilot Study.

PubMed

Al-Naji, Ali; Gibson, Kim; Lee, Sang-Heon; Chahl, Javaan

2017-02-03

The objective of this study was to design a non-invasive system for the observation of respiratory rates and detection of apnoea using analysis of real time image sequences captured in any given sleep position and under any light conditions (even in dark environments). A Microsoft Kinect sensor was used to visualize the variations in the thorax and abdomen from the respiratory rhythm. These variations were magnified, analyzed and detected at a distance of 2.5 m from the subject. A modified motion magnification system and frame subtraction technique were used to identify breathing movements by detecting rapid motion areas in the magnified frame sequences. The experimental results on a set of video data from five subjects (3 h for each subject) showed that our monitoring system can accurately measure respiratory rate and therefore detect apnoea in infants and young children. The proposed system is feasible, accurate, safe and low computational complexity, making it an efficient alternative for non-contact home sleep monitoring systems and advancing health care applications.

3D kinematic measurement of human movement using low cost fish-eye cameras

NASA Astrophysics Data System (ADS)

Islam, Atiqul; Asikuzzaman, Md.; Garratt, Matthew A.; Pickering, Mark R.

2017-02-01

3D motion capture is difficult when the capturing is performed in an outdoor environment without controlled surroundings. In this paper, we propose a new approach of using two ordinary cameras arranged in a special stereoscopic configuration and passive markers on a subject's body to reconstruct the motion of the subject. Firstly for each frame of the video, an adaptive thresholding algorithm is applied for extracting the markers on the subject's body. Once the markers are extracted, an algorithm for matching corresponding markers in each frame is applied. Zhang's planar calibration method is used to calibrate the two cameras. As the cameras use the fisheye lens, they cannot be well estimated using a pinhole camera model which makes it difficult to estimate the depth information. In this work, to restore the 3D coordinates we use a unique calibration method for fisheye lenses. The accuracy of the 3D coordinate reconstruction is evaluated by comparing with results from a commercially available Vicon motion capture system.

Structure Damage Simulations Accounting for Inertial Effects and Impact and Optimization of Grid-Stiffened Non-Circular Shells

NASA Technical Reports Server (NTRS)

Mei, Chuh; Jaunky, Navin

1999-01-01

The goal of this research project is to develop modelling and analysis strategy for the penetration of aluminium plates impacted by titanium impactors. Finite element analysis is used to study the penetration of aluminium plates impacted by titanium impactors in order to study the effect of such uncontained engine debris impacts on aircraft-like skin panels. LS-DYNA3D) is used in the simulations to model the impactor, test fixture frame and target barrier plate. The effects of mesh refinement, contact modeling, and impactor initial velocity and orientation were studied. The research project also includes development of a design tool for optimum design of grid-stiffened non-circular shells or panels subjected to buckling.

Low-cost solar array structure development

NASA Astrophysics Data System (ADS)

Wilson, A. H.

1981-06-01

Early studies of flat-plate arrays have projected costs on the order of $50/square meter for installed array support structures. This report describes an optimized low-cost frame-truss structure that is estimated to cost below $25/square meter, including all markups, shipping an installation. The structure utilizes a planar frame made of members formed from light-gauge galvanized steel sheet and is supposed in the field by treated-wood trusses that are partially buried in trenches. The buried trusses use the overburden soil to carry uplift wind loads and thus to obviate reinforced-concrete foundations. Details of the concept, including design rationale, fabrication and assembly experience, structural testing and fabrication drawings are included.

Low-cost solar array structure development

NASA Technical Reports Server (NTRS)

Wilson, A. H.

1981-01-01

Early studies of flat-plate arrays have projected costs on the order of $50/square meter for installed array support structures. This report describes an optimized low-cost frame-truss structure that is estimated to cost below $25/square meter, including all markups, shipping an installation. The structure utilizes a planar frame made of members formed from light-gauge galvanized steel sheet and is supposed in the field by treated-wood trusses that are partially buried in trenches. The buried trusses use the overburden soil to carry uplift wind loads and thus to obviate reinforced-concrete foundations. Details of the concept, including design rationale, fabrication and assembly experience, structural testing and fabrication drawings are included.

View south, wharf B, timber framing, detail of cross bracing, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View south, wharf B, timber framing, detail of cross bracing, recent galvanized straps, bolts and washers - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

Airborne Imagery Collections Barrow 2013

DOE Data Explorer

Cherry, Jessica; Crowder, Kerri

2015-07-20

The data here are orthomosaics, digital surface models (DSMs), and individual frames captured during low altitude airborne flights in 2013 at the Barrow Environmental Observatory. The orthomosaics, thermal IR mosaics, and DSMs were generated from the individual frames using Structure from Motion techniques.

Environmental Assessment (EA) for the Comprehensive Range Plan (CRP), Melrose Air Force Range (AFR), New Mexico

DTIC Science & Technology

2011-07-01

11,674 sq ft C-130 maintenance hangar with reinforced concrete footings, a foundation and footing slab, a structural steel frame, insulated metal...regional farming output significantly; however, it could potentially have a detrimental effect to the lessee. Environmental Justice – There are no...Facility – Construct a pre-engineered one story steel framed structure including the necessary concrete foundations to support the building.  SOF

Current and Future Applications of Mechanical Fasteners for Light-Frame Wood Structures: Proceedings of Mechanical Fasteners Plenary Session at the Forest Products Research Society Annual Meeting

Treesearch

Leslie H. Groom; [Compiler

1993-01-01

The title of this publication-"Current and Future Applications of Mechanical Fasteners for Light-Frame Wood Structures" is the theme of this plenary session from the 1991 annual meeting of the Forest Products Research Society (FPRS). This theme was chosen to address current issues in the forest products industry: changing design codes, fastener performance,...

Orthogonally interdigitated shielded serpentine travelling wave cathode ray tube deflection structure

DOEpatents

Hagen, E.C.; Hudson, C.L.

1995-07-25

A new deflection structure which deflects a beam of charged particles, such as an electron beam, includes a serpentine set for transmitting a deflection field, and a shielding frame for housing the serpentine set. The serpentine set includes a vertical serpentine deflection element and a horizontal serpentine deflection element. These deflection elements are identical, and are interdigitatedly and orthogonally disposed relative to each other, for forming a central transmission passage, through which the electron beam passes, and is deflected by the deflection field, so as to minimize drift space signal distortion. The shielding frame includes a plurality of ground blocks, and forms an internal serpentine trough within these ground blocks, for housing the serpentine set. The deflection structure further includes a plurality of feedthrough connectors which are inserted through the shielding frame, and which are electrically connected to the serpentine set. 10 figs.

On ethics and the earthquake resistant interior design of buildings.

PubMed

Hurol, Yonca

2014-03-01

The most common tectonic quality of modern structures, such as frame systems, is their flexibility; they are open for change. Although this characteristic is a big advantage in comparison to the inflexible masonry structures of the past, it might also create some serious problems, such as e.g. the lack of safety in the event of an earthquake, if the flexibility is not used consciously by architects and interior designers. This article attempts to define and establish some rules for the interior design of buildings with reinforced concrete frame systems. The rules for making subtractions from these structures and extending them by making additions to them are contained within this article. The main objective of this article is to derive some ethical values from these rules. Thus, the conclusion of the article focuses on the derivation of some ethical values for achieving earthquake resistant interior design of buildings with reinforced concrete frame systems.

Investigating plasma viscosity with fast framing photography in the ZaP-HD Flow Z-Pinch experiment

NASA Astrophysics Data System (ADS)

Weed, Jonathan Robert

The ZaP-HD Flow Z-Pinch experiment investigates the stabilizing effect of sheared axial flows while scaling toward a high-energy-density laboratory plasma (HEDLP > 100 GPa). Stabilizing flows may persist until viscous forces dissipate a sheared flow profile. Plasma viscosity is investigated by measuring scale lengths in turbulence intentionally introduced in the plasma flow. A boron nitride turbulence-tripping probe excites small scale length turbulence in the plasma, and fast framing optical cameras are used to study time-evolved turbulent structures and viscous dissipation. A Hadland Imacon 790 fast framing camera is modified for digital image capture, but features insufficient resolution to study turbulent structures. A Shimadzu HPV-X camera captures the evolution of turbulent structures with great spatial and temporal resolution, but is unable to resolve the anticipated Kolmogorov scale in ZaP-HD as predicted by a simplified pinch model.

Seismic analysis of the frame structure reformed by cutting off column and jacking based on stiffness ratio

NASA Astrophysics Data System (ADS)

Zhao, J. K.; Xu, X. S.

2017-11-01

The cutting off column and jacking technology is a method for increasing story height, which has been widely used and paid much attention in engineering. The stiffness will be changed after the process of cutting off column and jacking, which directly affects the overall seismic performance. It is usually necessary to take seismic strengthening measures to enhance the stiffness. A five story frame structure jacking project in Jinan High-tech Zone was taken as an example, and three finite element models were established which contains the frame model before lifting, after lifting and after strengthening. Based on the stiffness, the dynamic time-history analysis was carried out to research its seismic performance under the EL-Centro seismic wave, the Taft seismic wave and the Tianjin artificial seismic wave. The research can provide some guidance for the design and construction of the entire jack lifting structure.

Eta Carinae: An Observational Testbed for 3-D Interacting Wind Modeling

NASA Technical Reports Server (NTRS)

Gull, Theodore; Madura, Tom; Groh, Jose; Corcoran, Mike; Owocki, Stan

2011-01-01

Eta Car, with its very massive interacting winds, provides shocked arc-like structures dense enough to trace in forbidden emission lines out to 0.7" (1700 AU). As the massive binary is in a very elliptical orbit (e approx. 0.9), the spatial and velocity structures of these winds change over the 5.54 year period. We can tract ionization structures by several forbidden emission lines. With the addition of radiative transfer on a time-step frame-by-frame basis, we are learning much new information on the ballistic structures, and may gain insight on how molecules and dust might form in these very massive systems.

Differential approach to strategies of segmental stabilisation in postural control.

PubMed

Isableu, Brice; Ohlmann, Théophile; Crémieux, Jacques; Amblard, Bernard

2003-05-01

The present paper attempts to clarify the between-subjects variability exhibited in both segmental stabilisation strategies and their subordinated or associated sensory contribution. Previous data have emphasised close relationships between the interindividual variability in both the visual control of posture and the spatial visual perception. In this study, we focused on the possible relationships that might link perceptual visual field dependence-independence and the visual contribution to segmental stabilisation strategies. Visual field dependent (FD) and field independent (FI) subjects were selected on the basis of their extreme score in a static rod and frame test where an estimation of the subjective vertical was required. In the postural test, the subjects stood in the sharpened Romberg position in darkness or under normal or stroboscopic illumination, in front of either a vertical or a tilted frame. Strategies of segmental stabilisation of the head, shoulders and hip in the roll plane were analysed by means of their anchoring index (AI). Our hypothesis was that FD subjects might use mainly visual cues for calibrating not only their spatial perception but also their strategies of segmental stabilisation. In the case of visual cue disturbances, a greater visual dependency to the strategies of segmental stabilisation in FD subjects should be validated by observing more systematic "en bloc" functioning (i.e. negative AI) between two adjacent segments. The main results are the following: 1. Strategies of segmental stabilisation differed between both groups and differences were amplified with the deprivation of either total vision and/or static visual cues. 2. In the absence of total vision and/or static visual cues, FD subjects have shown an increased efficiency of the hip stabilisation in space strategy and an "en bloc" operation of the shoulder-hip unit (whole trunk). The last "en bloc" operation was extended to the whole head-trunk unit in darkness, associated with a hip stabilisation in space. 3. The FI subjects have adopted neither a strategy of segmental stabilisation in space nor on the underlying segment, whatever the body segment considered and the visual condition. Thus, in this group, head, shoulder and hip moved independently from each other during stance control, roughly without taking into account the visual condition. The results, emphasising a differential weighting of sensory input involved in both perceptual and postural control, are discussed in terms of the differential choice and/or ability to select the adequate frame of reference common to both cognitive and motor spatial activities. We assumed that a motor-somesthetics "neglect" or a lack of mastering of these inputs/outputs rather than a mere visual dependence in FD subjects would generate these interindividual differences in both spatial perception and postural balance. This proprioceptive "neglect" is assumed to lead FD subjects to sensory reweighting, whereas proprioceptive dominance would lead FI subjects to a greater ability in selecting the adequate frame of reference in the case of intersensory disturbances. Finally, this study also provides evidence for a new interpretation of the visual field dependence-independence dimension in both spatial perception and postural control.

Numerical Analysis of a Masonry Panel Reinforced with Pultruded FRP Frames

NASA Astrophysics Data System (ADS)

Casalegno, C.; Russo, S.; Sciarretta, F.

2018-05-01

The paper presents a numerical study on the retrofit of traditional masonry with pultruded GFRP profile frames adjacent to a wall and connected to it by mechanical fasteners. This kind of retrofit solution, not having been explored yet either in theory or practice, is similar to the common steel frame retrofits, but offers the advantages of lightness and durability of FRP composite materials. The retrofit system proposed, once proven effective and advantageous, would bring a considerable potential innovation into its available options. Three different frame geometries and two cases of masonry thickness were considered to investigate the effectiveness of the retrofit GFRP frame on the inplane static response of the wall to horizontal loads. The global and local (connection) failure behavior of the wall-frame system was investigated using the 3D finite-element method. A general increase in strength after the retrofit, up to about 130%, was found, and a switch from rocking to the diagonal tension failure mode was observed. The strength hierarchy of the retrofitted systems was also analyzed to clarify the effectiveness of the retrofit in imparting a residual strength to masonry. A thinner masonry structure was clearly recognized to have got the greatest benefits, but the retrofit could also significantly improve the inplane shear strength of a thicker wall. A comparison with steel structures of analogous capacity in terms of weight and natural vibration frequencies supported the viability of composite FRP frames for retrofit.

Low floor mass transit vehicle

DOEpatents

Emmons, J Bruce [Beverly Hills, MI; Blessing, Leonard J [Rochester, MI

2004-02-03

A mass transit vehicle includes a frame structure that provides an efficient and economical approach to providing a low floor bus. The inventive frame includes a stiff roof panel and a stiff floor panel. A plurality of generally vertical pillars extend between the roof and floor panels. A unique bracket arrangement is disclosed for connecting the pillars to the panels. Side panels are secured to the pillars and carry the shear stresses on the frame. A unique seating assembly that can be advantageously incorporated into the vehicle taking advantage of the load distributing features of the inventive frame is also disclosed.

Evaluation of a metal fuselage frame selectively reinforced with filamentary composites for space shuttle application

NASA Technical Reports Server (NTRS)

Oken, S.; Skoumal, D. E.; Straayer, J. W.

1974-01-01

The development of metal structures reinforced with filamentary composites as a weight saving feature of the space shuttle components is discussed. A frame was selected for study that was representative of the type of construction used in the bulk frames of the orbiter vehicle. Theoretical and experimental investigations were conducted. Component tests were performed to evaluate the critical details used in the designs and to provide credibility to the weight saving results. A model frame was constructed of the reinforced metal material to provide a final evaluation of the construction under realistic load conditions.

Effect of Steel Framing for Securing Drywall Panels on Thermal and Humidity Parameters of the Outer Walls

NASA Astrophysics Data System (ADS)

Major, Maciej; Kosiń, Mariusz

2017-12-01

The paper analyses the effect of steel framing used to secure drywall panels on thermal and humidity properties of outer walls. In the practice of building a light structure, the most popular components are steel and wood studs. They are used to obtain framing for building a wall (an outer wall in this study). Analysis presented in this study concerned the corner of the outer wall build using the technology of light steel framing. Computer simulation was used to perform thermal and humidity analysis for the joint of the outer wall.

Neurofunctional Correlates of Environmental Cognition: An fMRI Study with Images from Episodic Memory

PubMed Central

Gutyrchik, Evgeny; Bao, Yan; Blautzik, Janusch; Pöppel, Ernst; Zaytseva, Yuliya; Russell, Edmund

2015-01-01

This study capitalizes on individual episodic memories to investigate the question, how dif-ferent environments affect us on a neural level. Instead of using predefined environmental stimuli, this study relied on individual representations of beauty and pleasure. Drawing upon episodic memories we conducted two experiments. Healthy subjects imagined pleasant and non-pleasant environments, as well as beautiful and non-beautiful environments while neural activity was measured by using functional Magnetic Resonance Imaging. Although subjects found the different conditions equally simple to visualize, our results revealed more distribut-ed brain activations for non-pleasant and non-beautiful environments than for pleasant and beautiful environments. The additional regions activated in non-pleasant (left lateral prefrontal cortex) and non-beautiful environments (supplementary motor area, anterior cortical midline structures) are involved in self-regulation and top-down cognitive control. Taken together, the results show that perceptual experiences and emotional evaluations of environments within a positive and a negative frame of reference are based on distinct patterns of neural activity. We interpret the data in terms of a different cognitive and processing load placed by exposure to different environments. The results hint at the efficiency of subject-generated representations as stimulus material. PMID:25875000

Neurofunctional correlates of environmental cognition: an FMRI study with images from episodic memory.

PubMed

Vedder, Aline; Smigielski, Lukasz; Gutyrchik, Evgeny; Bao, Yan; Blautzik, Janusch; Pöppel, Ernst; Zaytseva, Yuliya; Russell, Edmund

2015-01-01

This study capitalizes on individual episodic memories to investigate the question, how dif-ferent environments affect us on a neural level. Instead of using predefined environmental stimuli, this study relied on individual representations of beauty and pleasure. Drawing upon episodic memories we conducted two experiments. Healthy subjects imagined pleasant and non-pleasant environments, as well as beautiful and non-beautiful environments while neural activity was measured by using functional Magnetic Resonance Imaging. Although subjects found the different conditions equally simple to visualize, our results revealed more distribut-ed brain activations for non-pleasant and non-beautiful environments than for pleasant and beautiful environments. The additional regions activated in non-pleasant (left lateral prefrontal cortex) and non-beautiful environments (supplementary motor area, anterior cortical midline structures) are involved in self-regulation and top-down cognitive control. Taken together, the results show that perceptual experiences and emotional evaluations of environments within a positive and a negative frame of reference are based on distinct patterns of neural activity. We interpret the data in terms of a different cognitive and processing load placed by exposure to different environments. The results hint at the efficiency of subject-generated representations as stimulus material.

The influence of ZrO2/20%Y2O3 and Al2O3 deposited coatings to the behavior of an aluminum alloy subjected to mechanical shock

NASA Astrophysics Data System (ADS)

Pintilei, G. L.; Crismaru, V. I.; Abrudeanu, M.; Munteanu, C.; Luca, D.; Istrate, B.

2015-10-01

Aluminum alloys are used in the aerospace industry due to their good mechanical properties and their low density compared with the density of steels. Usually the parts made of aluminum alloys contribute to the structural frame of aircrafts and they must withstand static and variable mechanical loads and also mechanical loads applied in a very short time which determine different phenomenon's in the material behavior then static or fatigue loads. This paper analysis the resilience of a 2024 aluminum alloy subjected to shock loads and the way how a coating can improve its behavior. For improving the behavior two coatings were considered: Al2O3 with 99.5% purity and ZrO2/20%Y2O3. The coatings were deposited on the base material by plasma spraying. The samples with and without coating were subject to mechanical shock to determine the resilience of the materials and the cracks propagation was investigated using SEM analysis. To highlight the physical phenomenon's that appear in the samples during the mechanical shock, explicit finite element analysis were done using Ansys 14.5 software.

Effects of context on risk taking and decision times in obsessive-compulsive disorder.

PubMed

Sip, Kamila E; Muratore, Alexandra F; Stern, Emily R

2016-04-01

Despite the fact that OCD patients show altered decision making in everyday life, few studies have investigated how patients make risky decisions and what contextual factors impact choices. We investigated cognitive context with the use of the "framing effect" task, which investigates decision making based on whether monetarily equivalent choice options are framed in terms of a potential to either lose (lose $20 out of $50) or gain (gain $30 out of $50) money. In addition, we manipulated social context by providing positive or neutral feedback on subjects' choices. Overall, participants were risk taking for options framed in terms of potential loss and risk averse for options framed in terms of potential gain (the classic framing effect). Although OCD patients were generally more risk averse, the effect of the frame on choices did not differ significantly from healthy participants and choices were not impacted by social context. Within OCD patients, greater self-reported indecisiveness was associated with a larger effect of the frame on choices. OCD patients were also significantly slower to make choices in the loss compared to gain frame, an effect that was not observed among healthy participants. Overall, our results suggest that the framing of choice options has a differential effect on decision times but not the actual choices made by OCD patients, and that patients are not sensitive to social feedback when making choices. The correlation between indecisiveness and the framing effect in OCD suggests that further work interrogating the relationship between specific symptoms and decision making among patients may yield new insights into the disorder. Copyright © 2016 Elsevier Ltd. All rights reserved.

Framing matters: Effects of framing on older adults’ exploratory decision-making

PubMed Central

Cooper, Jessica A.; Blanco, Nathaniel; Maddox, W. Todd

2016-01-01

We examined framing effects on exploratory decision-making. In Experiment 1 we tested older and younger adults in two decision-making tasks separated by one week, finding that older adults’ decision-making performance was preserved when maximizing gains, but declined when minimizing losses. Computational modeling indicates that younger adults in both conditions, and older adults in gains-maximization, utilized a decreasing threshold strategy (which is optimal), but older adults in losses were better fit by a fixed-probability model of exploration. In Experiment 2 we examined within-subjects behavior in older and younger adults in the same exploratory decision-making task, but without a time separation between tasks. We replicated the older adult disadvantage in loss-minimization from Experiment 1, and found that the older adult deficit was significantly reduced when the loss-minimization task immediately followed the gains-maximization task. We conclude that older adults’ performance in exploratory decision-making is hindered when framed as loss-minimization, but that this deficit is attenuated when older adults can first develop a strategy in a gains-framed task. PMID:27977218

Aging Studies of Cu-Sn Intermetallics in Cu Micropillars Used in Flip Chip Attachment onto Cu Lead Frames

NASA Astrophysics Data System (ADS)

Roma, Maria Penafrancia C.; Kudtarkar, Santosh; Kierse, Oliver; Sengupta, Dipak; Cho, Junghyun

2018-02-01

Copper micropillars plated onto a silicon die and soldered with Sn-Ag solder to a copper lead frame in a flip chip on lead package have been subjected to high-temperature storage at 150°C and 175°C for 500 h, 1000 h, and 1500 h. Cu6Sn5 and Cu3Sn intermetallic compounds were found on both sides of the solder, but the growth rates were not the same as evidenced by different values of the growth exponent n. Cu and Sn diffusion controlled the Cu3Sn growth in the Cu pillar interface ( n ≈ 0.5), while interface reactions controlled the growth in the Cu lead frame interface ( n ≈ 0.8). Increasing the aging temperature increased the growth of Cu3Sn as well as the presence of microvoids in the Cu lead frame side. Adding Ni as a barrier layer on the Cu pillar prevented the growth of Cu3Sn in the Cu pillar interface and reduced its growth rate on the lead frame side, even at higher aging temperatures.

Framing matters: Effects of framing on older adults' exploratory decision-making.

PubMed

Cooper, Jessica A; Blanco, Nathaniel J; Maddox, W Todd

2017-02-01

We examined framing effects on exploratory decision-making. In Experiment 1 we tested older and younger adults in two decision-making tasks separated by one week, finding that older adults' decision-making performance was preserved when maximizing gains, but it declined when minimizing losses. Computational modeling indicates that younger adults in both conditions, and older adults in gains maximization, utilized a decreasing threshold strategy (which is optimal), but older adults in losses were better fit by a fixed-probability model of exploration. In Experiment 2 we examined within-subject behavior in older and younger adults in the same exploratory decision-making task, but without a time separation between tasks. We replicated the older adult disadvantage in loss minimization from Experiment 1 and found that the older adult deficit was significantly reduced when the loss-minimization task immediately followed the gains-maximization task. We conclude that older adults' performance in exploratory decision-making is hindered when framed as loss minimization, but that this deficit is attenuated when older adults can first develop a strategy in a gains-framed task. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

17. VIEW SOUTHWEST, SHARED MASONRY WALL PIER AND UNDERSIDE FRAMING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. VIEW SOUTHWEST, SHARED MASONRY WALL PIER AND UNDERSIDE FRAMING OF GIRDER SPAN - Route 1 Extension, Structure No. 0703-161, Spanning Conrail-Newark & New York Industrial tracks, Richards Lane, & Hawkins Street at Routes 1 & 9 Southbound, Newark, Essex County, NJ

Computational multiobjective topology optimization of silicon anode structures for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Mitchell, Sarah L.; Ortiz, Michael

2016-09-01

This study utilizes computational topology optimization methods for the systematic design of optimal multifunctional silicon anode structures for lithium-ion batteries. In order to develop next generation high performance lithium-ion batteries, key design challenges relating to the silicon anode structure must be addressed, namely the lithiation-induced mechanical degradation and the low intrinsic electrical conductivity of silicon. As such this work considers two design objectives, the first being minimum compliance under design dependent volume expansion, and the second maximum electrical conduction through the structure, both of which are subject to a constraint on material volume. Density-based topology optimization methods are employed in conjunction with regularization techniques, a continuation scheme, and mathematical programming methods. The objectives are first considered individually, during which the influence of the minimum structural feature size and prescribed volume fraction are investigated. The methodology is subsequently extended to a bi-objective formulation to simultaneously address both the structural and conduction design criteria. The weighted sum method is used to derive the Pareto fronts, which demonstrate a clear trade-off between the competing design objectives. A rigid frame structure was found to be an excellent compromise between the structural and conduction design criteria, providing both the required structural rigidity and direct conduction pathways. The developments and results presented in this work provide a foundation for the informed design and development of silicon anode structures for high performance lithium-ion batteries.

Optical sectioning microscopy using two-frame structured illumination and Hilbert-Huang data processing

NASA Astrophysics Data System (ADS)

Trusiak, M.; Patorski, K.; Tkaczyk, T.

2014-12-01

We propose a fast, simple and experimentally robust method for reconstructing background-rejected optically-sectioned microscopic images using two-shot structured illumination approach. Innovative data demodulation technique requires two grid-illumination images mutually phase shifted by π (half a grid period) but precise phase displacement value is not critical. Upon subtraction of the two frames the input pattern with increased grid modulation is computed. The proposed demodulation procedure comprises: (1) two-dimensional data processing based on the enhanced, fast empirical mode decomposition (EFEMD) method for the object spatial frequency selection (noise reduction and bias term removal), and (2) calculating high contrast optically-sectioned image using the two-dimensional spiral Hilbert transform (HS). The proposed algorithm effectiveness is compared with the results obtained for the same input data using conventional structured-illumination (SIM) and HiLo microscopy methods. The input data were collected for studying highly scattering tissue samples in reflectance mode. In comparison with the conventional three-frame SIM technique we need one frame less and no stringent requirement on the exact phase-shift between recorded frames is imposed. The HiLo algorithm outcome is strongly dependent on the set of parameters chosen manually by the operator (cut-off frequencies for low-pass and high-pass filtering and η parameter value for optically-sectioned image reconstruction) whereas the proposed method is parameter-free. Moreover very short processing time required to efficiently demodulate the input pattern predestines proposed method for real-time in-vivo studies. Current implementation completes full processing in 0.25s using medium class PC (Inter i7 2,1 GHz processor and 8 GB RAM). Simple modification employed to extract only first two BIMFs with fixed filter window size results in reducing the computing time to 0.11s (8 frames/s).

Time-frequency analysis of functional optical mammographic images

NASA Astrophysics Data System (ADS)

Barbour, Randall L.; Graber, Harry L.; Schmitz, Christoph H.; Tarantini, Frank; Khoury, Georges; Naar, David J.; Panetta, Thomas F.; Lewis, Theophilus; Pei, Yaling

2003-07-01

We have introduced working technology that provides for time-series imaging of the hemoglobin signal in large tissue structures. In this study we have explored our ability to detect aberrant time-frequency responses of breast vasculature for subjects with Stage II breast cancer at rest and in response to simple provocations. The hypothesis being explored is that time-series imaging will be sensitive to the known structural and functional malformations of the tumor vasculature. Mammographic studies were conducted using an adjustable hemisheric measuring head containing 21 source and 21 detector locations (441 source-detector pairs). Simultaneous dual-wavelength studies were performed at 760 and 830 nm at a framing rate of ~2.7 Hz. Optical measures were performed on women lying prone with the breast hanging in a pendant position. Two class of measures were performed: (1) 20- minute baseline measure wherein the subject was at rest; (2) provocation studies wherein the subject was asked to perform some simple breathing maneuvers. Collected data were analyzed to identify the time-frequency structure and central tendencies of the detector responses and those of the image time series. Imaging data were generated using the Normalized Difference Method (Pei et al., Appl. Opt. 40, 5755-5769, 2001). Results obtained clearly document three classes of anomalies when compared to the normal contralateral breast. 1) Breast tumors exhibit altered oxygen supply/demand imbalance in response to an oxidative challenge (breath hold). 2) The vasomotor response of the tumor vasculature is mainly depressed and exhibits an altered modulation. 3) The affected area of the breast wherein the altered vasomotor signature is seen extends well beyond the limits of the tumor itself.

Shoulder torques resulting from luggage handling tasks in non-inertial frames.

PubMed

Shippen, James; May, Barbara

2018-05-18

This paper reports on the torques developed in the shoulder joint experienced by occupants of moving vehicles during manual handling tasks. Handling heavy weights can cause musculoskeletal injuries, especially if handling is done with arms extended or at high levels. The aim of the study was to measure the longitudinal and lateral accelerations in a variety of passenger vehicles together with the postures of subjects lifting luggage onto storage shelves. This data enabled the application of inverse dynamics methods in a non-inertial reference frame to calculate the shoulder joint torques. The subjects lifted 3 pieces of luggage of masses of 5 kg, 10 kg and 14 kg onto shelving which were at heights of 1.2 m, 1.6 m and 1.8 m. The movement of subjects was measured using a 12 camera, 3-dimensional optical tracking system. The subjects stood on force plates to measure the ground reaction forces. Sixty-three trials were completed, although 9 trials were aborted because subjects felt unable to complete the task. It was found that the shoulder torques exceeded the levels recommend by the UK Health and Safety Executive for manual handling. A lift assistance device is suggested to reduce the shoulder torques required for luggage handling.

Changes in Rod and Frame Test Scores Recorded in Schoolchildren during Development – A Longitudinal Study

PubMed Central

Bagust, Jeff; Docherty, Sharon; Haynes, Wayne; Telford, Richard; Isableu, Brice

2013-01-01

The Rod and Frame Test has been used to assess the degree to which subjects rely on the visual frame of reference to perceive vertical (visual field dependence- independence perceptual style). Early investigations found children exhibited a wide range of alignment errors, which reduced as they matured. These studies used a mechanical Rod and Frame system, and presented only mean values of grouped data. The current study also considered changes in individual performance. Changes in rod alignment accuracy in 419 school children were measured using a computer-based Rod and Frame test. Each child was tested at school Grade 2 and retested in Grades 4 and 6. The results confirmed that children displayed a wide range of alignment errors, which decreased with age but did not reach the expected adult values. Although most children showed a decrease in frame dependency over the 4 years of the study, almost 20% had increased alignment errors suggesting that they were becoming more frame-dependent. Plots of individual variation (SD) against mean error allowed the sample to be divided into 4 groups; the majority with small errors and SDs; a group with small SDs, but alignments clustering around the frame angle of 18°; a group showing large errors in the opposite direction to the frame tilt; and a small number with large SDs whose alignment appeared to be random. The errors in the last 3 groups could largely be explained by alignment of the rod to different aspects of the frame. At corresponding ages females exhibited larger alignment errors than males although this did not reach statistical significance. This study confirms that children rely more heavily on the visual frame of reference for processing spatial orientation cues. Most become less frame-dependent as they mature, but there are considerable individual differences. PMID:23724139

Analytical Approach to Large Deformation Problems of Frame Structures

NASA Astrophysics Data System (ADS)

Ohtsuki, Atsumi; Ellyin, Fernand

In elements used as flexible linking devices and structures, the main characteristic is a fairly large deformation without exceeding the elastic limit of the material. This property is of both analytical and technological interests. Previous studies of large deformation have been generally concerned with a single member (e.g. a cantilever beam, a simply supported beam, etc.). However, there are very few large deformation studies of assembled members such as frames. This paper deals with a square frame with rigid joints, loaded diagonally in either tension or compression by a pair of opposite forces. Analytical solutions for large deformation are obtained in terms of elliptic integrals, and are compared with the experimental data. The agreement is found to be fairly close.

Changes across age groups in self-choice elaboration effects on incidental memory.

PubMed

Toyota, Hiroshi; Konishi, Tomoko

2004-08-01

The present study investigated age differences in the effects of a self-choice elaboration and an experimenter-provided elaboration on incidental memory. Adults, sixth grade, and second grade subjects chose which of two sentence frames the target fit better in a self-choice elaboration condition. They then judged whether each target made sense in its sentence frame in the experimenter-provided elaboration, then did free recall tests. Only adults recalled better the targets with an image sentence with self-choice elaboration, rather than experimenter-provided elaboration. However, self-choice elaboration was far superior for the recall of targets with nonimage sentences only for second graders. Thus, the effects of self-choice elaboration were determined both by age and by type of sentence frame.

Self-corrected elaboration and spacing effects in incidental memory.

PubMed

Toyota, Hiroshi

2006-04-01

The present study investigated the effect of self-corrected elaboration on incidental memory as a function of types of presentation (massed vs spaced) and sentence frames (image vs nonimage). The subjects were presented a target word and an incongruous sentence frame and asked to correct the target to make a common sentence in the self-corrected elaboration condition, whereas in the experimenter-corrected elaboration condition they were asked to rate the appropriateness of the congruous word presented, followed by free recall test. The superiority of the self-corrected elaboration to the experimenter-corrected elaboration was observed only in some situations of combinations by the types of presentation and sentence frames. These results were discussed in terms of the effectiveness of the self-corrected elaboration.

Dynamic of charged planar geometry in tilted and non-tilted frames

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharif, M., E-mail: msharif.math@pu.edu.pk; Zaeem Ul Haq Bhatti, M., E-mail: mzaeem.math@pu.edu.pk

2015-05-15

We investigate the dynamics of charged planar symmetry with an anisotropic matter field subject to a radially moving observer called a tilted observer. The Einstein-Maxwell field equations are used to obtain a relation between non-tilted and tilted frames and between kinematical and dynamical quantities. Using the Taub mass formalism and conservation laws, two evolution equations are developed to analyze the inhomogeneities in the tilted congruence. It is found that the radial velocity (due to the tilted observer) and the electric charge have a crucial effect on the inhomogeneity factor. Finally, we discuss the stability in the non-tilted frame in themore » pure diffusion case and examine the effects of the electromagnetic field.« less

Real-time heart rate measurement for multi-people using compressive tracking

NASA Astrophysics Data System (ADS)

Liu, Lingling; Zhao, Yuejin; Liu, Ming; Kong, Lingqin; Dong, Liquan; Ma, Feilong; Pang, Zongguang; Cai, Zhi; Zhang, Yachu; Hua, Peng; Yuan, Ruifeng

2017-09-01

The rise of aging population has created a demand for inexpensive, unobtrusive, automated health care solutions. Image PhotoPlethysmoGraphy(IPPG) aids in the development of these solutions by allowing for the extraction of physiological signals from video data. However, the main deficiencies of the recent IPPG methods are non-automated, non-real-time and susceptible to motion artifacts(MA). In this paper, a real-time heart rate(HR) detection method for multiple subjects simultaneously was proposed and realized using the open computer vision(openCV) library, which consists of getting multiple subjects' facial video automatically through a Webcam, detecting the region of interest (ROI) in the video, reducing the false detection rate by our improved Adaboost algorithm, reducing the MA by our improved compress tracking(CT) algorithm, wavelet noise-suppression algorithm for denoising and multi-threads for higher detection speed. For comparison, HR was measured simultaneously using a medical pulse oximetry device for every subject during all sessions. Experimental results on a data set of 30 subjects show that the max average absolute error of heart rate estimation is less than 8 beats per minute (BPM), and the processing speed of every frame has almost reached real-time: the experiments with video recordings of ten subjects under the condition of the pixel resolution of 600× 800 pixels show that the average HR detection time of 10 subjects was about 17 frames per second (fps).

Research in structures, structural dynamics and materials, 1989

NASA Technical Reports Server (NTRS)

Hunter, William F. (Compiler); Noor, Ahmed K. (Compiler)

1989-01-01

Topics addressed include: composite plates; buckling predictions; missile launch tube modeling; structural/control systems design; optimization of nonlinear R/C frames; error analysis for semi-analytic displacement; crack acoustic emission; and structural dynamics.

Seismic Response of 3D Steel Buildings considering the Effect of PR Connections and Gravity Frames

PubMed Central

Haldar, Achintya; López-Barraza, Arturo; Rivera-Salas, J. Luz

2014-01-01

The nonlinear seismic responses of 3D steel buildings with perimeter moment resisting frames (PMRF) and interior gravity frames (IGF) are studied explicitly considering the contribution of the IGF. The effect on the structural response of the stiffness of the beam-to-column connections of the IGF, which is usually neglected, is also studied. It is commonly believed that the flexibility of shear connections is negligible and that 2D models can be used to properly represent 3D real structures. The results of the study indicate, however, that the moments developed on columns of IGF can be considerable and that modeling buildings as plane frames may result in very conservative designs. The contribution of IGF to the lateral structural resistance may be significant. The contribution increases when their connections are assumed to be partially restrained (PR). The incremented participation of IGF when the stiffness of their connections is considered helps to counteract the no conservative effect that results in practice when lateral seismic loads are not considered in IGF while designing steel buildings with PMRF. Thus, if the structural system under consideration is used, the three-dimensional model should be used in seismic analysis and the IGF and the stiffness of their connections should be considered as part of the lateral resistance system. PMID:24995357

Incremental dynamic analysis of concrete moment resisting frames reinforced with shape memory composite bars

NASA Astrophysics Data System (ADS)

Zafar, Adeel; Andrawes, Bassem

2012-02-01

Fiber reinforced polymer (FRP) reinforcing bars have been used in concrete structures as an alternative to conventional steel reinforcement, in order to overcome corrosion problems. However, due to the linear behavior of the commonly used reinforcing fibers, they are not considered in structures which require ductility and damping characteristics. The use of superelastic shape memory alloy (SMA) fibers with their nonlinear elastic behavior as reinforcement in the composite could potentially provide a solution for this problem. Small diameter SMA wires are coupled with polymer matrix to produce SMA-FRP composite, which is sought in this research as reinforcing bars. SMA-FRP bars are sought in this study to enhance the seismic performance of reinforced concrete (RC) moment resisting frames (MRFs) in terms of reducing their residual inter-story drifts while still maintaining the elastic characteristics associated with conventional FRP. Three story one bay and six story two bay RC MRF prototype structures are designed with steel, SMA-FRP and glass-FRP reinforcement. The incremental dynamic analysis technique is used to investigate the behaviors of the two frames with the three different reinforcement types under a suite of ground motion records. It is found that the frames with SMA-FRP composite reinforcement exhibit higher performance levels including lower residual inter-story drifts, high energy dissipation and thus lower damage, which are important for structures in highly seismic zones.

A network approach to policy framing: A case study of the National Aboriginal and Torres Strait Islander Health Plan.

PubMed

Browne, Jennifer; de Leeuw, Evelyne; Gleeson, Deborah; Adams, Karen; Atkinson, Petah; Hayes, Rick

2017-01-01

Aboriginal health policy in Australia represents a unique policy subsystem comprising a diverse network of Aboriginal-specific and "mainstream" organisations, often with competing interests. This paper describes the network structure of organisations attempting to influence national Aboriginal health policy and examines how the different subgroups within the network approached the policy discourse. Public submissions made as part of a policy development process for the National Aboriginal and Torres Strait Islander Health Plan were analysed using a novel combination of network analysis and qualitative framing analysis. Other organisational actors in the network in each submission were identified, and relationships between them determined; these were used to generate a network map depicting the ties between actors. A qualitative framing analysis was undertaken, using inductive coding of the policy discourses in the submissions. The frames were overlaid with the network map to identify the relationship between the structure of the network and the way in which organisations framed Aboriginal health problems. Aboriginal organisations were central to the network and strongly connected with each other. The network consisted of several densely connected subgroups, whose central nodes were closely connected to one another. Each subgroup deployed a particular policy frame, with a frame of "system dysfunction" also adopted by all but one subgroup. Analysis of submissions revealed that many of the stakeholders in Aboriginal health policy actors are connected to one another. These connections help to drive the policy discourse. The combination of network and framing analysis illuminates competing interests within a network, and can assist advocacy organisations to identify which network members are most influential. Copyright © 2016 Elsevier Ltd. All rights reserved.

Dynamic Imaging of the Eye, Optic Nerve, and Extraocular Muscles With Golden Angle Radial MRI

PubMed Central

Smith, David S.; Smith, Alex K.; Welch, E. Brian; Smith, Seth A.

2017-01-01

Purpose The eye and its accessory structures, the optic nerve and the extraocular muscles, form a complex dynamic system. In vivo magnetic resonance imaging (MRI) of this system in motion can have substantial benefits in understanding oculomotor functioning in health and disease, but has been restricted to date to imaging of static gazes only. The purpose of this work was to develop a technique to image the eye and its accessory visual structures in motion. Methods Dynamic imaging of the eye was developed on a 3-Tesla MRI scanner, based on a golden angle radial sequence that allows freely selectable frame-rate and temporal-span image reconstructions from the same acquired data set. Retrospective image reconstructions at a chosen frame rate of 57 ms per image yielded high-quality in vivo movies of various eye motion tasks performed in the scanner. Motion analysis was performed for a left–right version task where motion paths, lengths, and strains/globe angle of the medial and lateral extraocular muscles and the optic nerves were estimated. Results Offline image reconstructions resulted in dynamic images of bilateral visual structures of healthy adults in only ∼15-s imaging time. Qualitative and quantitative analyses of the motion enabled estimation of trajectories, lengths, and strains on the optic nerves and extraocular muscles at very high frame rates of ∼18 frames/s. Conclusions This work presents an MRI technique that enables high-frame-rate dynamic imaging of the eyes and orbital structures. The presented sequence has the potential to be used in furthering the understanding of oculomotor mechanics in vivo, both in health and disease. PMID:28813574

Decision-Making under Ambiguity Is Modulated by Visual Framing, but Not by Motor vs. Non-Motor Context. Experiments and an Information-Theoretic Ambiguity Model.

PubMed

Grau-Moya, Jordi; Ortega, Pedro A; Braun, Daniel A

2016-01-01

A number of recent studies have investigated differences in human choice behavior depending on task framing, especially comparing economic decision-making to choice behavior in equivalent sensorimotor tasks. Here we test whether decision-making under ambiguity exhibits effects of task framing in motor vs. non-motor context. In a first experiment, we designed an experience-based urn task with varying degrees of ambiguity and an equivalent motor task where subjects chose between hitting partially occluded targets. In a second experiment, we controlled for the different stimulus design in the two tasks by introducing an urn task with bar stimuli matching those in the motor task. We found ambiguity attitudes to be mainly influenced by stimulus design. In particular, we found that the same subjects tended to be ambiguity-preferring when choosing between ambiguous bar stimuli, but ambiguity-avoiding when choosing between ambiguous urn sample stimuli. In contrast, subjects' choice pattern was not affected by changing from a target hitting task to a non-motor context when keeping the stimulus design unchanged. In both tasks subjects' choice behavior was continuously modulated by the degree of ambiguity. We show that this modulation of behavior can be explained by an information-theoretic model of ambiguity that generalizes Bayes-optimal decision-making by combining Bayesian inference with robust decision-making under model uncertainty. Our results demonstrate the benefits of information-theoretic models of decision-making under varying degrees of ambiguity for a given context, but also demonstrate the sensitivity of ambiguity attitudes across contexts that theoretical models struggle to explain.

Performance and quality-control standards for composite floor, wall, and truss framing

Treesearch

Gerald A. Koenigshof

1985-01-01

Users must be assured that composite structural members are satisfactory for their intended purposes. Standards are provided for strength, stiffness, durability, and dimensional stability of composite floor, wall, and truss-framing members. Methods for enforcing compliance with the standards are suggested.

Mental transformations of spatial stimuli in humans and in monkeys: rotation vs. translocation.

PubMed

Nekovarova, Tereza; Nedvidek, Jan; Klement, Daniel; Rokyta, Richard; Bures, Jan

2013-03-01

We studied the ability of monkeys and humans to orient in one spatial frame ("response frame") according to abstract spatial stimuli presented in another spatial frame ("stimulus frame"). The stimuli were designed as simple maps of the "response space". We studied how the transformations of these stimuli affected the performance. The subjects were trained to choose a particular position in the response frame - either on a touch screen (monkeys) or on a keyboard (humans) - according to schematic spatial stimuli presented on the stimulus screen. The monkeys responded by touching one of four circles shown in corners of a rectangle displayed on the touch screen. The correct position was signaled by the stimulus ("map") presented on the stimulus screen. The map was a complementary rectangle, but only with one circle shown ("pointer"). The position of this circle indicated the correct position in the response frame. In the first experiment we only manipulated stimuli presented on the computer screen. The "map" was originally shown in the same position and orientation as the "response pattern" but later the position and the rotation of the map on the screen were changing. Such transformations of the stimuli allow us to study the mental operations that the animals performed and how particular mental transformations mutually differed. In the second experiment we tested whether the monkeys relied more on stimuli presented on the screen or on the surrounding stable environment and objects. We compared the performance of animals in tasks with rotated virtual maps in a stable surrounding environment with the performance in tasks where we rotated the surrounding frame (computer monitor), whereas the stimuli on the screen remained stable. In the third experiment we tested human subjects in analogous tests to compare the ability and cognitive strategies of monkeys and humans in this task. We showed that the mental strategies that monkeys used for orientation in one spatial frame according to the map presented in the other spatial frame depended on the type of stimulus manipulation. We demonstrated that for monkeys there was a difference between solving "mental rotation" and "mental translocation" in this experimental design. We showed that humans were able both to mentally rotate and translocate the displayed stimuli. However, the mental rotation was more difficult than mental translocation also for them. These experiments help us to understand how the monkeys perceive the abstract spatial information, create the representation of space and how they transform the information about the position obtained from one spatial frame into another. The comparison between humans and monkeys allows us to study this cognitive ability in phylogeny. Copyright © 2012 Elsevier B.V. All rights reserved.

Nonlinear Earthquake Analysis of Reinforced Concrete Frames with Fiber and Bernoulli-Euler Beam-Column Element

PubMed Central

Karaton, Muhammet

2014-01-01

A beam-column element based on the Euler-Bernoulli beam theory is researched for nonlinear dynamic analysis of reinforced concrete (RC) structural element. Stiffness matrix of this element is obtained by using rigidity method. A solution technique that included nonlinear dynamic substructure procedure is developed for dynamic analyses of RC frames. A predicted-corrected form of the Bossak-α method is applied for dynamic integration scheme. A comparison of experimental data of a RC column element with numerical results, obtained from proposed solution technique, is studied for verification the numerical solutions. Furthermore, nonlinear cyclic analysis results of a portal reinforced concrete frame are achieved for comparing the proposed solution technique with Fibre element, based on flexibility method. However, seismic damage analyses of an 8-story RC frame structure with soft-story are investigated for cases of lumped/distributed mass and load. Damage region, propagation, and intensities according to both approaches are researched. PMID:24578667

The mitochondnal genome of Aspergillus nidulans contains reading frames homologous to the human URFs 1 and 4.

PubMed Central

Brown, T A; Davies, R W; Ray, J A; Waring, R B; Scazzocchio, C

1983-01-01

A 2830-bp segment of the mitochondrial genome of the fungus Aspergillus nidulans was sequenced and shown to contain two unidentified reading frames (URFs). These reading frames are 352 and 488 codons in length, and would specify unmodified proteins of mol. wts. 39,000 and 54,000, respectively. The derived amino acid sequences indicate that these genes are equivalent to the human mitochondrial URFs 1 and 4, with 39% amino acid homology for URF1 and 26% for URF4. Both URFs were shown by secondary structure predictions to code for predominantly beta-sheeted proteins with strong structural conservation between the fungal and human homologues. Counterparts of mammalian URFs have not previously been identified in non-mammalian genomes, and the discovery that A. nidulans possesses reading frames so closely homologous with URF1 and URF4 shows that these genes are of general functional importance in the mitochondria of diverse species. PMID:11894959

Review on cold-formed steel connections.

PubMed

Lee, Yeong Huei; Tan, Cher Siang; Mohammad, Shahrin; Tahir, Mahmood Md; Shek, Poi Ngian

2014-01-01

The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed.

Review on Cold-Formed Steel Connections

PubMed Central

Tan, Cher Siang; Mohammad, Shahrin; Md Tahir, Mahmood; Shek, Poi Ngian

2014-01-01

The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed. PMID:24688448

Identity theory and personality theory: mutual relevance.

PubMed

Stryker, Sheldon

2007-12-01

Some personality psychologists have found a structural symbolic interactionist frame and identity theory relevant to their work. This frame and theory, developed in sociology, are first reviewed. Emphasized in the review are a multiple identity conception of self, identities as internalized expectations derived from roles embedded in organized networks of social interaction, and a view of social structures as facilitators in bringing people into networks or constraints in keeping them out, subsequently, attention turns to a discussion of the mutual relevance of structural symbolic interactionism/identity theory and personality theory, looking to extensions of the current literature on these topics.

Key Informant Models for Measuring Group-Level Variables in Small Groups: Application to Plural Subject Theory

ERIC Educational Resources Information Center

Algesheimer, René; Bagozzi, Richard P.; Dholakia, Utpal M.

2018-01-01

We offer a new conceptualization and measurement models for constructs at the group-level of analysis in small group research. The conceptualization starts with classical notions of group behavior proposed by Tönnies, Simmel, and Weber and then draws upon plural subject theory by philosophers Gilbert and Tuomela to frame a new perspective…

Educational Policy or Practice? Traversing the Conceptual Divide between Subject Knowledge, Pedagogy and Teacher Identity in England

ERIC Educational Resources Information Center

Woolhouse, Clare; Cochrane, Matt

2015-01-01

This research paper is framed by concerns about recent UK Government policy regarding the training of mathematics and science teachers in England and discusses how two cohorts of pre-service teachers negotiated the development of a professional identity while undertaking subject-specific training. The data reported upon were garnered in two ways;…

Seismic data interpolation and denoising by learning a tensor tight frame

NASA Astrophysics Data System (ADS)

Liu, Lina; Plonka, Gerlind; Ma, Jianwei

2017-10-01

Seismic data interpolation and denoising plays a key role in seismic data processing. These problems can be understood as sparse inverse problems, where the desired data are assumed to be sparsely representable within a suitable dictionary. In this paper, we present a new method based on a data-driven tight frame (DDTF) of Kronecker type (KronTF) that avoids the vectorization step and considers the multidimensional structure of data in a tensor-product way. It takes advantage of the structure contained in all different modes (dimensions) simultaneously. In order to overcome the limitations of a usual tensor-product approach we also incorporate data-driven directionality. The complete method is formulated as a sparsity-promoting minimization problem. It includes two main steps. In the first step, a hard thresholding algorithm is used to update the frame coefficients of the data in the dictionary; in the second step, an iterative alternating method is used to update the tight frame (dictionary) in each different mode. The dictionary that is learned in this way contains the principal components in each mode. Furthermore, we apply the proposed KronTF to seismic interpolation and denoising. Examples with synthetic and real seismic data show that the proposed method achieves better results than the traditional projection onto convex sets method based on the Fourier transform and the previous vectorized DDTF methods. In particular, the simple structure of the new frame construction makes it essentially more efficient.

The framing of two major flood episodes in the Irish print news media: Implications for societal adaptation to living with flood risk.

PubMed

Devitt, Catherine; O'Neill, Eoin

2017-10-01

Societal adaptation to flooding is a critical component of contemporary flood policy. Using content analysis, this article identifies how two major flooding episodes (2009 and 2014) are framed in the Irish broadsheet news media. The article considers the extent to which these frames reflect shifts in contemporary flood policy away from protection towards risk management, and the possible implications for adaptation to living with flood risk. Frames help us make sense of the social world, and within the media, framing is an essential tool for communication. Five frames were identified: flood resistance and structural defences, politicisation of flood risk, citizen as risk manager, citizen as victim and emerging trade-offs. These frames suggest that public debates on flood management do not fully reflect shifts in contemporary flood policy, with negative implications for the direction of societal adaptation. Greater discussion is required on the influence of the media on achieving policy objectives.

Research on discrete element simulation of anchor frame beam reinforcement in bedding shale slope

NASA Astrophysics Data System (ADS)

Zhang, Xiao yong; Xie, Xiao ting

2017-11-01

The anchor frame beam is a new type of composite support method, which is a kind of slope protection structure considering the interaction between the anchors and the slope. Based on the reinforcement project of a bedding shale slope in Chengzhang highway, the reinforced effect of anchor frame beam is studied by discrete element method. Firstly, the mesoscopic parameters of the rock mass are obtained by calibration while that of anchor frame beam are obtained by calculation. Then the slope model with the reinforcement of anchor frame beam is established by particle flow software PFC2D. Afterwards, the statement of slope can be analyzed and the reinforcement effect of anchor frame beam can be predicted. Results show that: there is no instability in the slope after reinforcement, and the sliding of slope can be effectively prevented by anchor frame beam. The simulation results can provide reference for the design and construction of the project.

Dominant frames in legacy and social media coverage of the IPCC Fifth Assessment Report

NASA Astrophysics Data System (ADS)

O'Neill, Saffron; Williams, Hywel T. P.; Kurz, Tim; Wiersma, Bouke; Boykoff, Maxwell

2015-04-01

The media are powerful agents that translate information across the science-policy interface, framing it for audiences. Yet frames are never neutral: they define an issue, identify causes, make moral judgements and shape proposed solutions. Here, we show how the IPCC Fifth Assessment Report (AR5) was framed in UK and US broadcast and print coverage, and on Twitter. Coverage of IPCC Working Group I (WGI) was contested and politicized, employing the `Settled Science, Uncertain Science, Political or Ideological Struggle and Role of Science’ frames. WGII coverage commonly used Disaster or Security. More diverse frames were employed for WGII and WGIII, including Economics and Morality and Ethics. Framing also varied by media institution: for example, the BBC used Uncertain Science, whereas Channel 4 did not. Coverage varied by working group, with WGIII gaining far less coverage than WGI or WGII. We suggest that media coverage and framing of AR5 was influenced by its sequential three-part structure and by the availability of accessible narratives and visuals. We recommend that these communication lessons be applied to future climate science reports.

Non Linear Analyses for the Evaluation of Seismic Behavior of Mixed R.C.-Masonry Structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liberatore, Laura; Tocci, Cesare; Masiani, Renato

2008-07-08

In this work the seismic behavior of masonry buildings with mixed structural system, consisting of perimeter masonry walls and internal r.c. frames, is studied by means of non linear static (pushover) analyses. Several aspects, like the distribution of seismic action between masonry and r.c. elements, the local and global behavior of the structure, the crisis of the connections and the attainment of the ultimate strength of the whole structure are examined. The influence of some parameters, such as the masonry compressive and tensile strength, on the structural behavior is investigated. The numerical analyses are also repeated on a building inmore » which the r.c. internal frames are replaced with masonry walls.« less

An overview of the crash dynamics failure behavior of metal and composite aircraft structures

NASA Technical Reports Server (NTRS)

Carden, Huey D.; Boitnott, Richard L.; Fasanella, Edwin L.; Jones, Lisa E.

1991-01-01

An overview of failure behavior results is presented from some of the crash dynamics research conducted with concepts of aircraft elements and substructure not necessarily designed or optimized for energy absorption or crash loading considerations. Experimental and analytical data are presented that indicate some general trends in the failure behavior of a class of composite structures that includes fuselage panels, individual fuselage sections, fuselage frames, skeleton subfloors with stringers and floor beams without skin covering, and subfloors with skin added to the frame stringer structure. Although the behavior is complex, a strong similarity in the static/dynamic failure behavior among these structures is illustrated through photographs of the experimental results and through analytical data of generic composite structural models.

The Attitude-Behavior Discrepancy in Medical Decision Making

PubMed Central

He, Fei; Li, Dongdong; Cao, Rong; Zeng, Juli; Guan, Hao

2014-01-01

Background: In medical practice, the dissatisfaction of patients about medical decisions made by doctors is often regarded as the fuse of doctor-patient conflict. However, a few studies have looked at why there are such dissatisfactions. Objectives: This experimental study aimed to explore the discrepancy between attitude and behavior within medical situations and its interaction with framing description. Patients and Methods: A total of 450 clinical undergraduates were randomly assigned to six groups and investigated using the classic medical decision making problem, which was described either in a positive or a negative frame (2) × decision making behavior\\attitude to risky plan\\attitude to conservative plan (3). Results: A discrepancy between attitude and behavior did exist in medical situations. Regarding medical dilemmas, if the mortality rate was described, subjects had a significant tendency to choose a conservative plan (t = 3.55, P < 0.01) yet if the survival rate was described, there was no such preference (t = -1.48, P > 0.05). However, regardless of the plan chosen by the doctor, the subjects had a significant opposing attitude (P < .05). Framing description had a significant impact on both decision making behavior and attitude (t behavior = -3.24, P < 0.01；t attitude to surgery = 4.08，P < 0.01；t attitude to radiation = -2.15，P < 0.05). Conclusions: A discrepancy of attitude-behavior does exist in medical situations. The framing of a description has an impact on medical decision-making. PMID:25763230

Approximate equiangular tight frames for compressed sensing and CDMA applications

NASA Astrophysics Data System (ADS)

Tsiligianni, Evaggelia; Kondi, Lisimachos P.; Katsaggelos, Aggelos K.

2017-12-01

Performance guarantees for recovery algorithms employed in sparse representations, and compressed sensing highlights the importance of incoherence. Optimal bounds of incoherence are attained by equiangular unit norm tight frames (ETFs). Although ETFs are important in many applications, they do not exist for all dimensions, while their construction has been proven extremely difficult. In this paper, we construct frames that are close to ETFs. According to results from frame and graph theory, the existence of an ETF depends on the existence of its signature matrix, that is, a symmetric matrix with certain structure and spectrum consisting of two distinct eigenvalues. We view the construction of a signature matrix as an inverse eigenvalue problem and propose a method that produces frames of any dimensions that are close to ETFs. Due to the achieved equiangularity property, the so obtained frames can be employed as spreading sequences in synchronous code-division multiple access (s-CDMA) systems, besides compressed sensing.

Putting Safety in the Frame: Nurses' Sensemaking at Work.

PubMed

O'Keeffe, Valerie Jean; Thompson, Kirrilly Rebecca; Tuckey, Michelle Rae; Blewett, Verna Lesley

2015-01-01

Current patient safety policy focuses nursing on patient care goals, often overriding nurses' safety. Without understanding how nurses construct work health and safety (WHS), patient and nurse safety cannot be reconciled. Using ethnography, we examine social contexts of safety, studying 72 nurses across five Australian hospitals making decisions during patient encounters. In enacting safe practice, nurses used "frames" built from their contextual experiences to guide their behavior. Frames are produced by nurses, and they structure how nurses make sense of their work. Using thematic analysis, we identify four frames that inform nurses' decisions about WHS: (a) communicating builds knowledge, (b) experiencing situations guides decisions, (c) adapting procedures streamlines work, and (d) team working promotes safe working. Nurses' frames question current policy and practice by challenging how nurses' safety is positioned relative to patient safety. Recognizing these frames can assist the design and implementation of effective WHS management.

Study on the effect of the infill walls on the seismic performance of a reinforced concrete frame

NASA Astrophysics Data System (ADS)

Zhang, Cuiqiang; Zhou, Ying; Zhou, Deyuan; Lu, Xilin

2011-12-01

Motivated by the seismic damage observed to reinforced concrete (RC) frame structures during the Wenchuan earthquake, the effect of infill walls on the seismic performance of a RC frame is studied in this paper. Infill walls, especially those made of masonry, offer some amount of stiffness and strength. Therefore, the effect of infill walls should be considered during the design of RC frames. In this study, an analysis of the recorded ground motion in the Wenchuan earthquake is performed. Then, a numerical model is developed to simulate the infill walls. Finally, nonlinear dynamic analysis is carried out on a RC frame with and without infill walls, respectively, by using CANNY software. Through a comparative analysis, the following conclusions can be drawn. The failure mode of the frame with infill walls is in accordance with the seismic damage failure pattern, which is strong beam and weak column mode. This indicates that the infill walls change the failure pattern of the frame, and it is necessary to consider them in the seismic design of the RC frame. The numerical model presented in this paper can effectively simulate the effect of infill walls on the RC frame.

An analytical and experimental investigation of the response of the curved, composite frame/skin specimens

NASA Technical Reports Server (NTRS)

Moas, Eduardo; Boitnott, Richard L.; Griffin, O. Hayden, Jr.

1994-01-01

Six-foot diameter, semicircular graphite/epoxy specimens representative of generic aircraft frames were loaded quasi-statistically to determine their load response and failure mechanisms for large deflections that occur in airplanes crashes. These frame/skin specimens consisted of a cylindrical skin section co-cured with a semicircular I-frame. The skin provided the necessary lateral stiffness to keep deformations in the plane of the frame in order to realistically represent deformations as they occur in actual fuselage structures. Various frame laminate stacking sequences and geometries were evaluated by statically loading the specimen until multiple failures occurred. Two analytical methods were compared for modeling the frame/skin specimens: a two-dimensional shell finite element analysis and a one-dimensional, closed-form, curved beam solution derived using an energy method. Flange effectivities were included in the beam analysis to account for the curling phenomenon that occurs in thin flanges of curved beams. Good correlation was obtained between experimental results and the analytical predictions of the linear response of the frames prior to the initial failure. The specimens were found to be useful for evaluating composite frame designs.

48 CFR 1352.271-88 - Guarantees.

Code of Federal Regulations, 2010 CFR

2010-10-01

... when practicable, the Government shall afford the contractor an opportunity to effect such corrections... expiration of the time frame stated in this clause, it is not subject to the time limitations stated in this...

7 CFR 762.130 - Loan approval and issuing the guarantee.

Code of Federal Regulations, 2010 CFR

2010-01-01

... this time frame is not met, the proposed guaranteed loan will automatically be approved, subject to... compensation, and personal life insurance (when required) are in effect; (iii) Truth in lending requirements...

Critical Frames in Educational Research: Feminist and Post-structural Perspectives.

ERIC Educational Resources Information Center

Lather, Patti

1992-01-01

Explores how qualitative and feminist inquiry are reconfiguring educational research, focusing on methodological issues involved in moving it into the postpositivist era. The article examines contributions of the transdisciplinary movements of feminism and poststructuralism in the development of critical frames in educational research. (SM)

"Speaking for another": the management of participant frames in aphasia.

PubMed

Simmons-Mackie, Nina; Kingston, Debbie; Schultz, Misty

2004-05-01

A sociolinguistic analysis of an interaction between a woman with aphasia and a nonaphasic speaking partner was conducted to investigate participant framing in aphasia. Participant frames, or the stances that people take in conversation, help conversational participants structure their talk and collaboratively negotiate meaning (I. Goffman, 1974). This analysis revealed a configuration in which a person with severe aphasia enlisted her speaking partner to speak for her. That is, the interaction was framed such that the nonaphasic speaking partner served as the "spokesperson" for messages that were authored by the person with aphasia. The clinical requirements of adopting a "speaking for another" framework are discussed.

Decentralized semi-active damping of free structural vibrations by means of structural nodes with an on/off ability to transmit moments

NASA Astrophysics Data System (ADS)

Poplawski, Blazej; Mikułowski, Grzegorz; Mróz, Arkadiusz; Jankowski, Łukasz

2018-02-01

This paper proposes, tests numerically and verifies experimentally a decentralized control algorithm with local feedback for semi-active mitigation of free vibrations in frame structures. The algorithm aims at transferring the vibration energy of low-order, lightly-damped structural modes into high-frequency modes of vibration, where it is quickly damped by natural mechanisms of material damping. Such an approach to mitigation of vibrations, known as the prestress-accumulation release (PAR) strategy, has been earlier applied only in global control schemes to the fundamental vibration mode of a cantilever beam. In contrast, the decentralization and local feedback allows the approach proposed here to be applied to more complex frame structures and vibration patterns, where the global control ceases to be intuitively obvious. The actuators (truss-frame nodes with controllable ability to transmit moments) are essentially unblockable hinges that become unblocked only for very short time periods in order to trigger local modal transfer of energy. The paper proposes a computationally simple model of the controllable nodes, specifies the control performance measure, yields basic characteristics of the optimum control, proposes the control algorithm and then tests it in numerical and experimental examples.