Freezing point depression in model Lennard-Jones solutions

NASA Astrophysics Data System (ADS)

Koschke, Konstantin; Jörg Limbach, Hans; Kremer, Kurt; Donadio, Davide

2015-09-01

Crystallisation of liquid solutions is of uttermost importance in a wide variety of processes in materials, atmospheric and food science. Depending on the type and concentration of solutes the freezing point shifts, thus allowing control on the thermodynamics of complex fluids. Here we investigate the basic principles of solute-induced freezing point depression by computing the melting temperature of a Lennard-Jones fluid with low concentrations of solutes, by means of equilibrium molecular dynamics simulations. The effect of solvophilic and weakly solvophobic solutes at low concentrations is analysed, scanning systematically the size and the concentration. We identify the range of parameters that produce deviations from the linear dependence of the freezing point on the molal concentration of solutes, expected for ideal solutions. Our simulations allow us also to link the shifts in coexistence temperature to the microscopic structure of the solutions.

Experimental study and numerical simulation of the salinity effect on water-freezing point and ice-melting rate

NASA Astrophysics Data System (ADS)

Qin, N.; Wu, Y.; Wang, H. W.; Wang, Y. Y.

2017-12-01

In this paper, based on the background of snowmelt de-icing tools, we studied the effect of salt on freezing point and melting rate of ice through laboratory test and FLUENT numerical simulation analysis. It was confirmed that the freezing point is inversely proportional to the salt solid content, and with the salt solid content increasing, the freezing process of salt water gradually accepts the curing rule of non-crystal solids. At the same temperature, an increase in the salt solid content, the ice melting rate increase by the empirical formula linking the melting time with temperature and salt content. The theoretical aspects of solid/fluid transformation are discussed in detail.

Critical viewpoints on the methods of realizing the metal freezing points of the ITS-90

NASA Astrophysics Data System (ADS)

Ma, C. K.

1995-08-01

The time-honored method for realizing the freezing point tf of a metal (in practice necessarily a dilute alloy) is that of continuous, slow freezing where the plateau temperature (which is the result of solidifying material's being so pure that its phase-transition temperature is observably constant) is measured. The freezing point being an equilibrium temperature, Ancsin considers this method to be inappropriate in principle: equilibrium between the solid and liquid phases cannot be achieved while the solid is being cooled to dispose of the releasing latent heat and while it is accreting at the expense of the liquid. In place of the continuous freezing method he has employed the pulse-heating method (in which the sample is allowed to approach equilibrium after each heat pulse) in his study of Ag; his measurements suggest that freezing can produce non-negligible errors. Here we examine both methods and conclude that the freezing method, employing an inside solid-liquid interface thermally isolated by an outside interface, can provide realizations of the highest accuracy; in either method, perturbation, by inducing solid-liquid phase transition continuously or intermittently, is essential for detecting equilibrium thermally. The respective merits and disadvantages of these two methods and also of the inner-melt method are discussed. We conclude that in a freezing-point measurement what is being measured is in effect the however minutely varying phase transition, and nonconstitutional equilibrium, temperature ti at the solid-liquid interface. The objective is then to measure the ti that is the best measure of tf, which is, normally, the plateau temperature.

Preliminary analysis of aircraft fuel systems for use with broadened specification jet fuels

NASA Technical Reports Server (NTRS)

Pasion, A. J.; Thomas, I.

1977-01-01

An analytical study was conducted on the use of broadened specification hydrocarbon fuels in present day aircraft. A short range Boeing 727 mission and three long range Boeing 747 missions were used as basis of calculation for one-day-per-year extreme values of fuel loading, airport ambient and altitude ambient temperatures with various seasonal and climatic conditions. Four hypothetical fuels were selected; two high-vapor-pressure fuels with 35 kPa and 70 kPa RVP and two high-freezing-point fuels with -29 C and -18 C freezing points. In-flight fuel temperatures were predicted by Boeing's aircraft fuel tank thermal analyzer computer program. Boil-off rates were calculated for the high vapor pressure fuels and heating/insulation requirements for the high freezing point fuels were established. Possible minor and major heating system modifications were investigated with respect to heat output, performance and economic penalties for the high freezing point fuels.

Evaluation of methods for rapid determination of freezing point of aviation fuels

NASA Technical Reports Server (NTRS)

Mathiprakasam, B.

1982-01-01

Methods for identification of the more promising concepts for the development of a portable instrument to rapidly determine the freezing point of aviation fuels are described. The evaluation process consisted of: (1) collection of information on techniques previously used for the determination of the freezing point, (2) screening and selection of these techniques for further evaluation of their suitability in a portable unit for rapid measurement, and (3) an extensive experimental evaluation of the selected techniques and a final selection of the most promising technique. Test apparatuses employing differential thermal analysis and the change in optical transparency during phase change were evaluated and tested. A technique similar to differential thermal analysis using no reference fuel was investigated. In this method, the freezing point was obtained by digitizing the data and locating the point of inflection. Results obtained using this technique compare well with those obtained elsewhere using different techniques. A conceptual design of a portable instrument incorporating this technique is presented.

Preservation of flavor in freeze dried green beans

NASA Technical Reports Server (NTRS)

Huber, C. S.; Heidelbaugh, N. D.; Davis, D.

1973-01-01

Before freeze drying, green beans are heated to point at which their cell structure is altered. Beans freeze dried with altered cell structure have improved rehydration properties and retain color, flavor, and texture.

A Determination of the Ratio of the Zinc Freezing Point to the Tin Freezing Point by Noise Thermometry

NASA Astrophysics Data System (ADS)

Labenski, J. R.; Tew, W. L.; Benz, S. P.; Nam, S. W.; Dresselhaus, P.

2008-02-01

A Johnson-noise thermometer (JNT) has been used with a quantized voltage noise source (QVNS), as a calculable reference to determine the ratio of temperatures near the Zn freezing point to those near the Sn freezing point. The temperatures are derived in a series of separate measurements comparing the synthesized noise power from the QVNS with that of Johnson noise from a known resistance. The synthesized noise power is digitally programed to match the thermal noise powers at both temperatures and provides the principle means of scaling the temperatures. This produces a relatively flat spectrum for the ratio of spectral noise densities, which is close to unity in the low-frequency limit. The data are analyzed as relative spectral ratios over the 4.8 to 450 kHz range averaged over a 3.2 kHz bandwidth. A three-parameter model is used to account for differences in time constants that are inherently temperature dependent. A drift effect of approximately -6 μK·K-1 per day is observed in the results, and an empirical correction is applied to yield a relative difference in temperature ratios of -11.5 ± 43 μK·K-1 with respect to the ratio of temperatures assigned on the International Temperature Scale of 1990 (ITS-90). When these noise thermometry results are combined with results from acoustic gas thermometry at temperatures near the Sn freezing point, a value of T - T 90 = 7 ± 30 mK for the Zn freezing point is derived.

Note: equation of state and the freezing point in the hard-sphere model.

PubMed

Robles, Miguel; López de Haro, Mariano; Santos, Andrés

2014-04-07

The merits of different analytical equations of state for the hard-sphere system with respect to the recently computed high-accuracy value of the freezing-point packing fraction are assessed. It is found that the Carnahan-Starling-Kolafa and the branch-point approximant equations of state yield the best performance.

Effects of Pressure-shift Freezing on the Structural and Physical Properties of Gelatin Hydrogel Matrices

PubMed Central

Kim, Byeongsoo; Gil, Hyung Bae; Min, Sang-Gi; Lee, Si-Kyung; Choi, Mi-Jung

2014-01-01

This study investigates the effects of the gelatin concentration (10-40%, w/v), freezing temperatures (from -20℃ to -50℃) and freezing methods on the structural and physical properties of gelatin matrices. To freeze gelatin, the pressure-shift freezing (PSF) is being applied at 0.1 (under atmospheric control), 50 and 100 MPa, respectively. The freezing point of gelatin solutions decrease with increasing gelatin concentrations, from -0.2℃ (10% gelatin) to -6.7℃ (40% gelatin), while the extent of supercooling did not show any specific trends. The rheological properties of the gelatin indicate that both the storage (G') and loss (G") moduli were steady in the strain amplitude range of 0.1-10%. To characterize gelatin matrices formed by the various freezing methods, the ice crystal sizes which were being determined by the scanning electron microscopy (SEM) are affected by the gelatin concentrations. The ice crystal sizes are affected by gelatin concentrations and freezing temperature, while the size distributions of ice crystals depend on the freezing methods. Smaller ice crystals are being formed with PSF rather than under the atmospheric control where the freezing temperature is above -40℃. Thus, the results of this study indicate that the PSF processing at a very low freezing temperature (-50℃) offers a potential advantage over commercial atmospheric freezing points for the formation of small ice crystals. PMID:26760743

Synchrotron X-Ray Visualisation of Ice Formation in Insects during Lethal and Non-Lethal Freezing

PubMed Central

Sinclair, Brent J.; Gibbs, Allen G.; Lee, Wah-Keat; Rajamohan, Arun; Roberts, Stephen P.; Socha, John J.

2009-01-01

Although the biochemical correlates of freeze tolerance in insects are becoming well-known, the process of ice formation in vivo is subject to speculation. We used synchrotron x-rays to directly visualise real-time ice formation at 3.3 Hz in intact insects. We observed freezing in diapausing 3rd instar larvae of Chymomyza amoena (Diptera: Drosophilidae), which survive freezing if it occurs above −14°C, and non-diapausing 3rd instar larvae of C. amoena and Drosophila melanogaster (Diptera: Drosophilidae), neither of which survive freezing. Freezing was readily observed in all larvae, and on one occasion the gut was seen to freeze separately from the haemocoel. There were no apparent qualitative differences in ice formation between freeze tolerant and non-freeze tolerant larvae. The time to complete freezing was positively related to temperature of nucleation (supercooling point, SCP), and SCP declined with decreasing body size, although this relationship was less strong in diapausing C. amoena. Nucleation generally occurred at a contact point with the thermocouple or chamber wall in non-diapausing larvae, but at random in diapausing larvae, suggesting that the latter have some control over ice nucleation. There were no apparent differences between freeze tolerant and non-freeze tolerant larvae in tracheal displacement or distension of the body during freezing, although there was markedly more distension in D. melanogaster than in C. amoena regardless of diapause state. We conclude that although control of ice nucleation appears to be important in freeze tolerant individuals, the physical ice formation process itself does not differ among larvae that can and cannot survive freezing. This suggests that a focus on cellular and biochemical mechanisms is appropriate and may reveal the primary adaptations allowing freeze tolerance in insects. PMID:20011523

Temperature and flow measurements on near-freezing aviation fuels in a wing-tank model

NASA Technical Reports Server (NTRS)

Friedman, R.; Stockemer, F. J.

1980-01-01

Freezing behavior, pumpability, and temperature profiles for aviation turbine fuels were measured in a 190-liter tank chilled to simulate internal temperature gradients encountered in commercial airplane wing tanks. When the bulk of the fuel was above the specification freezing point, pumpout of the fuel removed all fuel except a layer adhering to the bottom chilled surfaces, and the unpumpable fraction depended on the fuel temperature near these surfaces. When the bulk of the fuel was at or below the freezing point, pumpout ceased when solids blocked the pump inlet, and the unpumpable fraction depended on the overall average temperature.

Microbial analysis and survey test of gamma-irradiated freeze-dried fruits for patient's food

NASA Astrophysics Data System (ADS)

Park, Jae-Nam; Sung, Nak-Yun; Byun, Eui-Hong; Byun, Eui-Baek; Song, Beom-Seok; Kim, Jae-Hun; Lee, Kyung-A.; Son, Eun-Joo; Lyu, Eun-Soon

2015-06-01

This study examined the microbiological and organoleptic qualities of gamma-irradiated freeze-dried apples, pears, strawberries, pineapples, and grapes, and evaluated the organoleptic acceptability of the sterilized freeze-dried fruits for hospitalized patients. The freeze-dried fruits were gamma-irradiated at 0, 1, 2, 3, 4, 5, 10, 12, and 15 kGy, and their quality was evaluated. Microorganisms were not detected in apples after 1 kGy, in strawberries and pears after 4 kGy, in pineapples after 5 kGy, and in grapes after 12 kGy of gamma irradiation. The overall acceptance score, of the irradiated freeze-dried fruits on a 7-point scale at the sterilization doses was 5.5, 4.2, 4.0, 4.1, and 5.1 points for apples, strawberries, pears, pineapples, and grapes, respectively. The sensory survey of the hospitalized cancer patients (N=102) resulted in scores of 3.8, 3.7, 3.9, 3.9, and 3.7 on a 5-point scale for the gamma-irradiated freeze-dried apples, strawberries, pears, pineapples, and grapes, respectively. The results suggest that freeze-dried fruits can be sterilized with a dose of 5 kGy, except for grapes, which require a dose of 12 kGy, and that the organoleptic quality of the fruits is acceptable to immuno-compromised patients. However, to clarify the microbiological quality and safety of freeze-dried fruits should be verified by plating for both aerobic and anaerobic microorganisms.

THE FREEZING POINT DEPRESSION OF MAMMALIAN TISSUES IN RELATION TO THE QUESTION OF OSMOTIC ACTIVITY OF CELL FLUID

PubMed Central

Brodsky, William A.; Appelboom, Johannes W.; Dennis, Warren H.; Rehm, Warren S.; Miley, John F.; Diamond, Israel

1956-01-01

The freezing point depression of freshly excised frozen tissues, pulverized in a hydraulic press or in a mortar, is greater than that of plasma. Even at 0°C. the freezing point depression of such homogenates increases significantly with time. Dilution data indicate that such freezing point data are valid. The presence of intact cells has been shown in smears of tissues pulverized in a mortar, but not in smears of those crushed in a hydraulic press. The osmolarity of various diluent solutions affects the calculated osmotic activity of tissue homogenates presumably because of delayed diffusion between the diluent and cell fluid. With a hypertonic NaCl diluent, spuriously low values of tissue osmotic activity are found from calculations assuming instantaneous mixing between homogenates and diluents. The limitations of data from cryoscopic experiments and from tissue-swelling experiments are discussed in relation to the basic question of whether or not cell fluid is isotonic to extracellular fluid. PMID:13385447

Freeze-drying process design by manometric temperature measurement: design of a smart freeze-dryer.

PubMed

Tang, Xiaolin Charlie; Nail, Steven L; Pikal, Michael J

2005-04-01

To develop a procedure based on manometric temperature measurement (MTM) and an expert system for good practices in freeze drying that will allow development of an optimized freeze-drying process during a single laboratory freeze-drying experiment. Freeze drying was performed with a FTS Dura-Stop/Dura-Top freeze dryer with the manometric temperature measurement software installed. Five percent solutions of glycine, sucrose, or mannitol with 2 ml to 4 ml fill in 5 ml vials were used, with all vials loaded on one shelf. Details of freezing, optimization of chamber pressure, target product temperature, and some aspects of secondary drying are determined by the expert system algorithms. MTM measurements were used to select the optimum shelf temperature, to determine drying end points, and to evaluate residual moisture content in real-time. MTM measurements were made at 1 hour or half-hour intervals during primary drying and secondary drying, with a data collection frequency of 4 points per second. The improved MTM equations were fit to pressure-time data generated by the MTM procedure using Microcal Origin software to obtain product temperature and dry layer resistance. Using heat and mass transfer theory, the MTM results were used to evaluate mass and heat transfer rates and to estimate the shelf temperature required to maintain the target product temperature. MTM product dry layer resistance is accurate until about two-thirds of total primary drying time is over, and the MTM product temperature is normally accurate almost to the end of primary drying provided that effective thermal shielding is used in the freeze-drying process. The primary drying times can be accurately estimated from mass transfer rates calculated very early in the run, and we find the target product temperature can be achieved and maintained with only a few adjustments of shelf temperature. The freeze-dryer overload conditions can be estimated by calculation of heat/mass flow at the target product temperature. It was found that the MTM results serve as an excellent indicator of the end point of primary drying. Further, we find that the rate of water desorption during secondary drying may be accurately measured by a variation of the basic MTM procedure. Thus, both the end point of secondary drying and real-time residual moisture may be obtained during secondary drying. Manometric temperature measurement and the expert system for good practices in freeze drying does allow development of an optimized freeze-drying process during a single laboratory freeze-drying experiment.

Key composition optimization of meat processed protein source by vacuum freeze-drying technology.

PubMed

Ma, Yan; Wu, Xingzhuang; Zhang, Qi; Giovanni, Vigna; Meng, Xianjun

2018-05-01

Vacuum freeze-drying technology is a high technology content, a wide range of knowledge of technology in the field of drying technology is involved, it is also a method of the most complex drying equipment, the largest energy consumption, the highest cost of drying method, but due to the particularity of its dry goods: the freeze-drying food has the advantages of complex water performance is good, cooler and luster of freezing and drying food to maintain good products, less nutrient loss, light weight, easy to carry transportation, easy to long-term preservation, and on the quality is far superior to the obvious advantages of other dried food, making it become the forefront of drying technology research and development. The freeze-drying process of Chinese style ham and western Germany fruit tree tenderloin is studied in this paper, their eutectic point, melting point and collapse temperature, freeze-drying curve and its heat and mass transfer characteristics are got, then the precool temperature and the highest limiting temperature of sublimation interface are determined. The effect of system pressure on freeze-dried rate in freeze-drying process is discussed, and the method of regulating pressure circularly is determined.

High-freezing-point fuels used for aviation turbine engines

NASA Technical Reports Server (NTRS)

Friedman, R.

1979-01-01

Broadened-specification aviation fuels could be produced from a greater fraction of crude source material with improvements in fuel supply and price. These fuels, particularly those with increased final boiling temperatures, would have higher freezing temperatures than current aviation turbine fuels. The higher-freezing-point fuels can be substituted in the majority of present commercial flights, since temperature data indicate that in-flight fuel temperatures are relatively mild. For the small but significant fraction of commercial flights where low fuel temperatures make higher freezing-point fuel use unacceptable, adaptations to the fuel or fuel system may be made to accommodate this fuel. Several techniques are discussed. Fuel heating is the most promising concept. One simple system design uses existing heat rejection from the fuel-lubricating oil cooler, another uses an engine-driven generator for electrical heating. Both systems offer advantages that outweigh the obvious penalties.

THE FREEZING POINT DEPRESSION OF MAMMALIAN TISSUES AFTER SUDDEN HEATING IN BOILING DISTILLED WATER

PubMed Central

Appelboom, Johannes W. Th.; Brodsky, William A.; Tuttle, William S.; Diamond, Israel

1958-01-01

The calculated freezing point depression of freshly excised boiled mammalian tissue is approximately the same as that of plasma. The boiling procedure was chosen to eliminate the influence of metabolism on the level of the freezing point depression. Problems created by the boiling, such as equilibrium between tissue and diluent, change in activity coefficient by dilution, and loss of CO2 content, are discussed. A frozen crushed tissue homogenate is hypertonic to plasma. Boiling and dilution of such hypertonic homogenate exposed to room temperature for 5 to 15 minutes did not produce significant or unexplicable decreases in its osmotic activity. Moreover, freezing and crushing of a boiled diluted tissue did not produce any increase of the isoosmotic level of freezing point depression. It is possible to explain these data either with the hypothesis of hypertonic cell fluid or with that of isotonic cell fluid. In the case of an assumed isotonic cell fluid, data can be explained with one assumption, experimentally backed. In the case of an assumed hypertonic theory data can be explained only with the help of at least three ad hoc postulates. The data support the validity of the classical concept which holds that cell fluid is isotonic to extracellular fluid. PMID:13563805

How do Polar Stratospheric Clouds Form?

NASA Technical Reports Server (NTRS)

Drdla, Katja; Gandrud, Bruce; Baumgardner, Darrel; Herman, Robert; Gore, Warren J. (Technical Monitor)

2000-01-01

SOLVE measurements have been compared with results from a microphysical model to understand the composition and formation of the polar stratospheric clouds (PSCs) observed during SOLVE. Evidence that the majority of the particles remain liquid throughout the winter will be presented. However, a small fraction of the particles do freeze, and the presence of these frozen particles can not be explained by current theories, in which the only freezing mechanism is homogeneous freezing to ice below the ice frost point. Alternative formation mechanisms, in particular homogeneous freezing above the ice frost point and heterogeneous freezing, have been explored using the microphysical model. Both nitric acid trihydrate (NAT) and nitric acid dihydrate (NAD) have been considered as possible compositions for the solid-phase nitric acid aerosols. Comparisons between the model results and the SOLVE measurements will be used to constrain the possible formation mechanisms. Other effects of these frozen particles will also be discussed, in particular denitrification.

A hyperactive, Ca2+-dependent antifreeze protein in an Antarctic bacterium.

PubMed

Gilbert, Jack A; Davies, Peter L; Laybourn-Parry, Johanna

2005-04-01

In cold climates, some plants and bacteria that cannot avoid freezing use antifreeze proteins (AFPs) to lessen the destructive effects of ice recrystallization. These AFPs have weak freezing point depression activity, perhaps to avoid sudden, uncontrolled growth of ice. Here, we report on an uncharacteristically powerful bacterial AFP found in an Antarctic strain of the bacterium, Marinomonas primoryensis. It is Ca(2+)-dependent, shows evidence of cooperativity, and can produce over 2 degrees C of freezing point depression. Unlike most AFPs, it does not produce obvious crystal faceting during thermal hysteresis. This AFP might be capable of imparting freezing avoidance to M. primoryensis in ice-covered Antarctic lakes. A hyperactive bacterial AFP has not previously been reported.

Effects of freezing conditions on quality changes in blueberries.

PubMed

Cao, Xuehui; Zhang, Fangfang; Zhao, Dongyu; Zhu, Danshi; Li, Jianrong

2018-03-12

Freezing preservation is one of the most effective methods used to maintain the flavour and nutritional value of fruit. This research studied the effects of different freezing conditions, -20 °C, -40 °C, -80 °C, and immersion in liquid nitrogen, on quality changes of freeze-thawed blueberries. The water distribution estimates of blueberries were measured based on low-field nuclear magnetic resonance (LF-NMR) analysis. The pectin content, drip loss, and fruit texture were also detected to evaluate quality changes in samples. The freezing curves of blueberry showed super-cooling points at -20 °C and - 40 °C, whereas super-cooling points were not observed at -80 °C or in liquid nitrogen. After freeze-thaw treatment, the relaxation time of the cell wall water (T 21 ), cytoplasm water and extracellular space (T 22 ), and vacuole water (T 23 ) were significantly shortened compared to fresh samples, which suggested a lower liquidity. Although the freezing speed for samples immersed in liquid nitrogen was faster than other treatments, samples treated at -80 °C showed better quality regarding vacuole water holding, drip loss, and original pectin content retention. This study contributed to understanding how freezing temperature affects the qualities of blueberries. The super-fast freezing rate might injure fruit, and an appropriate freezing rate could better preserve blueberries. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Inactivation of Kudoa septempunctata in olive flounder meat by liquid freezing.

PubMed

Ohnishi, Takahiro; Akuzawa, Sayuri; Furusawa, Hiroko; Yoshinari, Tomoya; Kamata, Yoichi; Sugita-Konishi, Yoshiko

2014-01-01

Kudoa septempunctata in olive flounder meat was inactivated using 3 distinct freezing methods：liquid freezing for 5 min, air blast freezing at －30℃ for 5 h, and －80℃ for 1 h. The fracture curve of olive flounder meat subjected to liquid freezing resembled that of meat stored at 4℃, indicating that the structure of olive flounder muscle was well preserved. In contrast, air blast freezing induced the disappearance of the fracture point in the fracture curve, indicating that there was deterioration in the meat quality. Liquid freezing preserved the transparency of olive flounder meat to the same degree as that of meat stored at 4°C. However, air blast freezing induced meat cloudiness. These results indicate that liquid freezing can be used for K. septempunctata inactivation without affecting the meat quality.

Investigating Freezing Point Depression and Cirrus Cloud Nucleation Mechanisms Using a Differential Scanning Calorimeter

ERIC Educational Resources Information Center

Bodzewski, Kentaro Y.; Caylor, Ryan L.; Comstock, Ashley M.; Hadley, Austin T.; Imholt, Felisha M.; Kirwan, Kory D.; Oyama, Kira S.; Wise, Matthew E.

2016-01-01

A differential scanning calorimeter was used to study homogeneous nucleation of ice from micron-sized aqueous ammonium sulfate aerosol particles. It is important to understand the conditions at which these particles nucleate ice because of their connection to cirrus cloud formation. Additionally, the concept of freezing point depression, a topic…

Fluid property measurements study

NASA Technical Reports Server (NTRS)

Devaney, W. E.

1976-01-01

Fluid properties of refrigerant-21 were investigated at temperatures from the freezing point to 423 Kelvin and at pressures to 1.38 x 10 to the 8th power N/sq m (20,000 psia). The fluid properties included were: density, vapor pressure, viscosity, specific heat, thermal conductivity, thermal expansion coefficient, freezing point and bulk modulus. Tables of smooth values are reported.

Animal ice-binding (antifreeze) proteins and glycolipids: an overview with emphasis on physiological function.

PubMed

Duman, John G

2015-06-01

Ice-binding proteins (IBPs) assist in subzero tolerance of multiple cold-tolerant organisms: animals, plants, fungi, bacteria etc. IBPs include: (1) antifreeze proteins (AFPs) with high thermal hysteresis antifreeze activity; (2) low thermal hysteresis IBPs; and (3) ice-nucleating proteins (INPs). Several structurally different IBPs have evolved, even within related taxa. Proteins that produce thermal hysteresis inhibit freezing by a non-colligative mechanism, whereby they adsorb onto ice crystals or ice-nucleating surfaces and prevent further growth. This lowers the so-called hysteretic freezing point below the normal equilibrium freezing/melting point, producing a difference between the two, termed thermal hysteresis. True AFPs with high thermal hysteresis are found in freeze-avoiding animals (those that must prevent freezing, as they die if frozen) especially marine fish, insects and other terrestrial arthropods where they function to prevent freezing at temperatures below those commonly experienced by the organism. Low thermal hysteresis IBPs are found in freeze-tolerant organisms (those able to survive extracellular freezing), and function to inhibit recrystallization - a potentially damaging process whereby larger ice crystals grow at the expense of smaller ones - and in some cases, prevent lethal propagation of extracellular ice into the cytoplasm. Ice-nucleator proteins inhibit supercooling and induce freezing in the extracellular fluid at high subzero temperatures in many freeze-tolerant species, thereby allowing them to control the location and temperature of ice nucleation, and the rate of ice growth. Numerous nuances to these functions have evolved. Antifreeze glycolipids with significant thermal hysteresis activity were recently identified in insects, frogs and plants. © 2015. Published by The Company of Biologists Ltd.

Triple point determinations of monomethylhydrazine and nitrogen tetroxide, 2.2 percent by weight nitric oxide

NASA Technical Reports Server (NTRS)

Smith, Irwin D.; Dhooge, Patrick M.

1977-01-01

A series of tests was performed to ascertain the triple points of monomethylhydrazine and nitrogen tetroxide. A laboratory method indicated a triple point for monomethylhydrazine, but tests in a large vacuum chamber indicated that a triple point does not occur in spacelike conditions because the mono-methylhydrazine tends to supercool. Instead, an effective freezing point (with agitation) was obtained. New experimental values for liquid monomethylhydrazine vapor pressure were determined for temperatures from 275.2 to 207.6 K. The values were used to derive vapor pressure equations. Tentative values were obtained for the effective freezing point of nitrogen tetroxide spacelike conditions.

Production of Low-Freezing-Point Highly Branched Alkanes through Michael Addition.

PubMed

Jing, Yaxuan; Xia, Qineng; Liu, Xiaohui; Wang, Yanqin

2017-12-22

A new approach for the production of low-freezing-point, high-quality fuels from lignocellulose-derived molecules was developed with Michael addition as the key step. Among the investigated catalysts, CoCl 2 ⋅6 H 2 O was found most active for the Michael addition of 2,4-pentanedione with FA (single aldol adduct of furfural and acetone, 4-(2-furanyl)-3-butene-2-one). Over CoCl 2 ⋅6 H 2 O, a high carbon yield of C 13 oxygenates (about 75 %) can be achieved under mild conditions (353 K, 20 h). After hydrodeoxygenation, low-freezing-point (<223 K) branched alkanes with 13 carbons within jet fuel ranges were obtained over a Pd/NbOPO 4 catalyst. Furthermore, C 18,23 fuel precursors could be easily synthesized through Michael addition of 2,4-pentanedione with DFA (double-condensation product of furfural and acetone) under mild conditions and the molar ratio of C 18 /C 23 is dependent on the reaction conditions of Michael addition. After hydrodeoxygenation, high density (0.8415 g mL -1 ) and low-freezing-point (<223 K) branched alkanes with 18, 23 carbons within lubricant range were also obtained over a Pd/NbOPO 4 catalyst. These highly branched alkanes can be directly used as transportation fuels or additives. This work opens a new strategy for the synthesis of highly branched alkanes with low freezing point from renewable biomass. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Kinetic freeze-out conditions for the production of resonances, hadronic molecules, and light nuclei

NASA Astrophysics Data System (ADS)

Cho, Sungtae; Song, Taesoo; Lee, Su Houng

2018-02-01

We investigate the freeze-out conditions of a particle in an expanding system of interacting particles in order to understand the productions of resonances, hadronic molecules, and light nuclei in heavy-ion collisions. Applying the kinetic freeze-out condition with explicit hydrodynamic calculations for the expanding hadronic phase to the daughter particles of K* mesons, we find that the larger suppression of the yield ratio of K*/K at the Large Hadron Collider (LHC) than at the Relativisitic Heavy Ion Collider (RHIC) compared to the expectations from the statistical hadronization model based on chemical freeze-out parameters reflects the lower kinetic freeze-out temperature at LHC than at RHIC. Furthermore, we point out that for the light nuclei or hadronic molecules that are bound, the freeze-out condition should be applied to the respective particle in the hadronic matter. It is then shown through the rate equation that when the nucleon and pion numbers are kept constant at the chemical freeze-out value during the hadronic phase, the deuteron number quickly approaches an asymptotic value that is close to the statistical model prediction at the chemical freeze-out point. We argue that the reduction seen in K* numbers is a typical result for a particle that has a large natural decay width decaying into daughter particles, while that for deuteron is typical for a stable hadronic bound state.

Fuel system technology overview

NASA Technical Reports Server (NTRS)

Friedman, R.

1980-01-01

Fuel system research and technology studies are being conducted to investigate the correlations and interactions of aircraft fuel system design and environment with applicable characteristics of the fuel. Topics include: (1) analysis of in-flight fuel temperatures; (2) fuel systems for high freezing point fuels; (3) experimental study of low temperature pumpability; (4) full scale fuel tank simulation; and (5) rapid freezing point measurement.

Nickel-Silver Monotectic in Alumina Crucible for Use with Contact Thermometry

NASA Astrophysics Data System (ADS)

Gotoh, M.; Dedyulin, S. N.

2017-07-01

Previously, the authors have published work describing a pure Ni fixed point within alumina crucibles. The success of this study stimulated working with the Ni-Ag monotectic point in alumina crucibles. Similar to eutectic points, the Ni-Ag monotectic temperature is an invariant point but it differs from a eutectic reaction in such a way that the monotectic phase change takes place from Ni-Ag liquid solution to Ni-Ag solid solution and Ag rich Ni-Ag liquid solution. In the phase diagram references, the Ni-Ag monotectic phase transition temperature is assigned to be about 20°C below the pure Ni melting/freezing point. As is the case for pure Ni, mechanical stability is one of the concerns. Therefore, proper cell design is necessary to avoid breakage of the alumina crucible. The techniques used for the fabrication and measurement of the pure Ni cell were applied to the Ni-Ag cell as well. The cells have been successfully fabricated and the temperature measurement at the fixed point was carried out for more than 20 thermal cycles in total. A Pt/Pd thermocouple was used to measure the temperature and was calibrated from the tin point to the gold point to measure the ITS-90. Freezing plateaus are realized with the technique of "recurrent offset freezing method with reserved solid". The duration of each freezing plateau is a minimum of 30 min. The monotectic transformation temperature for the best performed cell is determined as 1428.27°C with a combined uncertainty of ±0.06°C ({k}=1).

Surface freezing of water.

PubMed

Pérez-Díaz, J L; Álvarez-Valenzuela, M A; Rodríguez-Celis, F

2016-01-01

Freezing, melting, evaporation and condensation of water are essential ingredients for climate and eventually life on Earth. In the present work, we show how surface freezing of supercooled water in an open container is conditioned and triggered-exclusively-by humidity in air. Additionally, a change of phase is demonstrated to be triggered on the water surface forming surface ice crystals prior to freezing of bulk. The symmetry of the surface crystal, as well as the freezing point, depend on humidity, presenting at least three different types of surface crystals. Humidity triggers surface freezing as soon as it overpasses a defined value for a given temperature, generating a plurality of nucleation nodes. An evidence of simultaneous nucleation of surface ice crystals is also provided.

Jet aircraft hydrocarbon fuels technology

NASA Technical Reports Server (NTRS)

Longwell, J. P. (Editor)

1978-01-01

A broad specification, referee fuel was proposed for research and development. This fuel has a lower, closely specified hydrogen content and higher final boiling point and freezing point than ASTM Jet A. The workshop recommended various priority items for fuel research and development. Key items include prediction of tradeoffs among fuel refining, distribution, and aircraft operating costs; combustor liner temperature and emissions studies; and practical simulator investigations of the effect of high freezing point and low thermal stability fuels on aircraft fuel systems.

Efficient Atomization and Combustion of Emulsified Crude Oil

DTIC Science & Technology

2014-09-18

2.26 Naphthenes , vol % 50.72 Aromatics, vol % 16.82 Freezing Point, °F -49.7 Freezing Point, °C -45.4 Smoke Point, mm (ASTM) 19.2 Acid ...needed by the proposed method for capturing and oil removal , in particular the same vessels and booms used to herd the floating crude oil into a thick...slicks need to be removed more rapidly than they can be transported, in situ burning offers a rapid disposal method that minimizes risk to marine life

High freezing point fuels used for aviation turbine engines

NASA Technical Reports Server (NTRS)

Friedman, R.

1979-01-01

Broadened-specification aviation fuels could be produced from a greater fraction of crude source material with improvements in fuel supply and price. These fuels, particularly those with increased final boiling temperatures, would have higher freezing temperatures than current aviation turbine fuels. For the small but significant fraction of commercial flights where low fuel temperatures make higher freezing-point fuel use unacceptable, adaptations to the fuel or fuel system may be made to accommodate this fuel. Several techniques are discussed. Fuel heating is the most promising concept. One simple design uses existing heat rejection from the fuel-lubricating oil cooler, another uses an engine-driven generator for electrical heating.

Physical properties of NaCl-free cucumber fermentation cover brine containing calcium chloride and glycerin and apparent freezing injury of the brined fruits

USDA-ARS?s Scientific Manuscript database

Use of glycerin and calcium chloride to reduce the freezing point and improve quality of bulk stored fermented cucumbers brined without NaCl, was explored. The incidence of pre-freezing injury on the fruits, caused by deposition in tanks containing cushion brine prepared with 2.5% calcium chloride, ...

Experimental Study of Fuel Heating at Low Temperatures in a Wing Tank Model, Volume 1

NASA Technical Reports Server (NTRS)

Stockemer, F. J.

1981-01-01

Scale model fuel heating systems for use with aviation hydrocarbon fuel at low temperatures were investigated. The effectiveness of the heating systems in providing flowability and pumpability at extreme low temperature when some freezing of the fuel would otherwise occur is evaluated. The test tank simulated a section of an outer wing tank, and was chilled on the upper and lower surfaces. Turbine engine lubricating oil was heated, and recirculating fuel transferred the heat. Fuels included: a commercial Jet A; an intermediate freeze point distillate; a higher freeze point distillate blended according to Experimental Referee Broadened Specification guidelines; and a higher freeze point paraffinic distillate used in a preceding investigation. Each fuel was chilled to selected temperature to evaluate unpumpable solid formation (holdup). Tests simulating extreme cold weather flight, without heating, provided baseline fuel holdup data. Heating and recirculating fuel increased bulk temperature significantly; it had a relatively small effect on temperature near the bottom of the tank. Methods which increased penetration of heated fuel into the lower boundary layer improved the capability for reducing holdup.

Novel Real-Time Diagnosis of the Freezing Process Using an Ultrasonic Transducer

PubMed Central

Tseng, Yen-Hsiang; Cheng, Chin-Chi; Cheng, Hong-Ping; Lee, Dasheng

2015-01-01

The freezing stage governs several critical parameters of the freeze drying process and the quality of the resulting lyophilized products. This paper presents an integrated ultrasonic transducer (UT) in a stainless steel bottle and its application to real-time diagnostics of the water freezing process. The sensor was directly deposited onto the stainless steel bottle using a sol-gel spray technique. It could operate at temperature range from −100 to 400 °C and uses an ultrasonic pulse-echo technique. The progression of the freezing process, including water-in, freezing point and final phase change of water, were all clearly observed using ultrasound. The ultrasonic signals could indicate the three stages of the freezing process and evaluate the cooling and freezing periods under various processing conditions. The temperature was also adopted for evaluating the cooling and freezing periods. These periods increased with water volume and decreased with shelf temperature (i.e., speed of freezing). This study demonstrates the effectiveness of the ultrasonic sensor and technology for diagnosing and optimizing the process of water freezing to save energy. PMID:25946629

Effect of hydroprocessing severity on characteristics of jet fuel from OSCO 2 and Paraho distillates

NASA Technical Reports Server (NTRS)

Prok, G. M.; Flores, F. J.; Seng, G. T.

1981-01-01

Jet A boiling range fuels and broad-property research fuels were produced by hydroprocessing shale oil distillates, and their properties were measured to characterize the fuels. The distillates were the fraction of whole shale oil boiling below 343 C from TOSCO 2 and Paraho syncrudes. The TOSCO 2 was hydroprocessed at medium severity, and the Paraho was hydroprocessed at high, medium, and low severities. Fuels meeting Jet A requirements except for the freezing point were produced from the medium severity TOSCO 2 and the high severity Paraho. Target properties of a broad property research fuel were met by the medium severity TOSCO 2 and the high severity Paraho except for the freezing point and a high hydrogen content. Medium and low severity Paraho jet fuels did not meet thermal stability and freezing point requirements.

THE ACTION OF EXTREME COLD ON LEUKEMIC CELLS OF MICE

PubMed Central

Breedis, Charles

1942-01-01

Suspensions of leukemic cells of mice from three different strains of leukemia were subjected to rapid or slow freezing and rapid or slow thawing. Suspensions rapidly frozen to –196°C. were in all cases innocuous, whereas those frozen slowly were capable of transmitting leukemia. The infectivity of slowly frozen material varied from an estimated 0.0001 per cent to 1 per cent of that of fresh material, and this figure probably represents the percentage of surviving leukemic cells. Particles of spleen and lymph node reacted to slow and rapid freezing in the same manner as suspensions prepared from them. For one of the strains rapid thawing was less injurious than slow thawing; for the other two the rate of thawing seemed to be immaterial. Infectivity was equally well preserved after freezing to –21°C. whether freezing occurred spontaneously after supercooling or was initiated near the freezing point by inoculation with ice, or whether thawing was slow or rapid. Suspensions already slowly frozen at temperatures of –2° or lower, whether spontaneously or by inoculation with ice, could no longer be completely inactivated by subsequent rapid cooling to –196°C. Unfrozen suspensions initially above the freezing point or supercooled to –2°C. or –8°C. and then rapidly cooled to –196°C. were inactivated. This protective action of previous slow freezing was most marked when the initial temperature of the frozen suspension was –15°C. or lower; when it was –2°C. protection was barely detected. These observations indicate that the changes which are peculiar to rapid freezing alone and lead to complete inactivation take place during rapid transition from the liquid to the solid state, in a range of temperature lying between –15°C. and the freezing point. Temperature measurements carried out in this range showed that suspensions were about equally infections whether the temperature at their centers dropped from 0°C. to –15°C. in 30 minutes or in 1 minute; when the drop occurred in 12 seconds or less, the suspensions became innocuous. PMID:19871231

Impurity Correction Techniques Applied to Existing Doping Measurements of Impurities in Zinc

NASA Astrophysics Data System (ADS)

Pearce, J. V.; Sun, J. P.; Zhang, J. T.; Deng, X. L.

2017-01-01

Impurities represent the most significant source of uncertainty in most metal fixed points used for the realization of the International Temperature Scale of 1990 (ITS-90). There are a number of different methods for quantifying the effect of impurities on the freezing temperature of ITS-90 fixed points, many of which rely on an accurate knowledge of the liquidus slope in the limit of low concentration. A key method of determining the liquidus slope is to measure the freezing temperature of a fixed-point material as it is progressively doped with a known amount of impurity. Recently, a series of measurements of the freezing and melting temperature of `slim' Zn fixed-point cells doped with Ag, Fe, Ni, and Pb were presented. Here, additional measurements of the Zn-X system are presented using Ga as a dopant, and the data (Zn-Ag, Zn-Fe, Zn-Ni, Zn-Pb, and Zn-Ga) have been re-analyzed to demonstrate the use of a fitting method based on Scheil solidification which is applied to both melting and freezing curves. In addition, the utility of the Sum of Individual Estimates method is explored with these systems in the context of a recently enhanced database of liquidus slopes of impurities in Zn in the limit of low concentration.

Freezing induces a loss of freeze tolerance in an overwintering insect.

PubMed

Brown, C L; Bale, J S; Walters, K F A

2004-07-22

Cold-hardy insects overwinter by one of two main strategies: freeze tolerance and freeze avoidance by supercooling. As a general model, many freeze-tolerant species overwinter in extreme climates, freeze above -10 degrees C via induction by ice-nucleating agents, and once frozen, can survive at temperatures of up to 40 degrees C or more below the initial freezing temperature or supercooling point (SCP). It has been assumed that the SCP of freeze-tolerant insects is unaffected by the freezing process and that the freeze-tolerant state is therefore retained in winter though successive freeze-thaw cycles of the body tissues and fluids. Studies on the freeze-tolerant larva of the hoverfly Syrphus ribesii reveal this assumption to be untrue. When a sample with a mean 'first freeze' SCP of -7.6 degrees C (range of -5 degrees C to -9.5 degrees C) were cooled, either to -10 degrees C or to their individual SCP, on five occasions, the mean SCP was significantly depressed, with some larvae subsequently freezing as low as -28 degrees C. Only larvae that froze at the same consistently high temperature above -10 degrees C were alive after being frozen five times. The wider occurrence of this phenomenon would require a fundamental reassessment of the dynamics and distinctions of the freeze-tolerant and freeze-avoiding strategies of insect overwintering. Copyright 2004 The Royal Society

Influence of surface groups of proteins on water studied by freezing/thawing hysteresis and infrared spectroscopy.

PubMed

Zelent, Bogumil; Bryan, Michael A; Sharp, Kim A; Vanderkooi, Jane M

2009-05-01

The influence of proteins and solutes on hysteresis of freezing and melting of water was measured by infrared (IR) spectroscopy. Of the solutes examined, poly-L-arginine and flounder antifreeze protein produced the largest freezing point depression of water, with little effect on the melting temperature. Poly-L-lysine, poly-L-glutamate, cytochrome c and bovine serum albumin had less effect on the freezing of water. Small compounds used to mimic non-polar (trimethylamine N-oxide, methanol), positively charged (guanidinium chloride, NH(4)Cl, urea) and negatively charged (Na acetate) groups on protein surfaces were also examined. These molecules and ions depress water's freezing point and the melting profiles became broad. Since infrared absorption measures both bulk solvent and solvent bound to the solutes, this result is consistent with solutes interacting with liquid water. The amide I absorption bands of antifreeze protein and poly-L-arginine do not detectably change with the phase transition of water. An interpretation is that the antifreeze protein and poly-L-arginine order liquid water such that the water around the group is ice-like.

Implementation of a process analytical technology system in a freeze-drying process using Raman spectroscopy for in-line process monitoring.

PubMed

De Beer, T R M; Allesø, M; Goethals, F; Coppens, A; Heyden, Y Vander; De Diego, H Lopez; Rantanen, J; Verpoort, F; Vervaet, C; Remon, J P; Baeyens, W R G

2007-11-01

The aim of the present study was to propose a strategy for the implementation of a Process Analytical Technology system in freeze-drying processes. Mannitol solutions, some of them supplied with NaCl, were used as models to freeze-dry. Noninvasive and in-line Raman measurements were continuously performed during lyophilization of the solutions to monitor real time the mannitol solid state, the end points of the different process steps (freezing, primary drying, secondary drying), and physical phenomena occurring during the process. At-line near-infrared (NIR) and X-ray powder diffractometry (XRPD) measurements were done to confirm the Raman conclusions and to find out additional information. The collected spectra during the processes were analyzed using principal component analysis and multivariate curve resolution. A two-level full factorial design was used to study the significant influence of process (freezing rate) and formulation variables (concentration of mannitol, concentration of NaCl, volume of freeze-dried sample) upon freeze-drying. Raman spectroscopy was able to monitor (i) the mannitol solid state (amorphous, alpha, beta, delta, and hemihydrate), (ii) several process step end points (end of mannitol crystallization during freezing, primary drying), and (iii) physical phenomena occurring during freeze-drying (onset of ice nucleation, onset of mannitol crystallization during the freezing step, onset of ice sublimation). NIR proved to be a more sensitive tool to monitor sublimation than Raman spectroscopy, while XRPD helped to unravel the mannitol hemihydrate in the samples. The experimental design results showed that several process and formulation variables significantly influence different aspects of lyophilization and that both are interrelated. Raman spectroscopy (in-line) and NIR spectroscopy and XRPD (at-line) not only allowed the real-time monitoring of mannitol freeze-drying processes but also helped (in combination with experimental design) us to understand the process.

Investigations into the low temperature behavior of jet fuels: Visualization, modeling, and viscosity studies

NASA Astrophysics Data System (ADS)

Atkins, Daniel L.

Aircraft operation in arctic regions or at high altitudes exposes jet fuel to temperatures below freeze point temperature specifications. Fuel constituents may solidify and remain within tanks or block fuel system components. Military and scientific requirements have been met with costly, low freeze point specialty jet fuels. Commercial airline interest in polar routes and the use of high altitude unmanned aerial vehicles (UAVs) has spurred interest in the effects of low temperatures and low-temperature additives on jet fuel. The solidification of jet fuel due to freezing is not well understood and limited visualization of fuel freezing existed prior to the research presented in this dissertation. Consequently, computational fluid dynamics (CFD) modeling that simulates jet fuel freezing and model validation were incomplete prior to the present work. The ability to simulate jet fuel freezing is a necessary tool for fuel system designers. An additional impediment to the understanding and simulation of jet fuel freezing has been the absence of published low-temperature thermo-physical properties, including viscosity, which the present work addresses. The dissertation is subdivided into three major segments covering visualization, modeling and validation, and viscosity studies. In the first segment samples of jet fuel, JPTS, kerosene, Jet A and Jet A containing additives, were cooled below their freeze point temperatures in a rectangular, optical cell. Images and temperature data recorded during the solidification process provided information on crystal habit, crystallization behavior, and the influence of the buoyancy-driven flow on freezing. N-alkane composition of the samples was determined. The Jet A sample contained the least n-alkane mass. The cooling of JPTS resulted in the least wax formation while the cooling of kerosene yielded the greatest wax formation. The JPTS and kerosene samples exhibited similar crystallization behavior and crystal habits during cooling. Low-temperature additives modified the crystal habit of the Jet A fuel. Crystal shapes and sizes were recorded for use in future computational modeling. In the second segment, a computational fluid dynamics model was developed that simulates the solidification of jet fuel due to freezing in a buoyancy-driven flow. Flow resistance caused by porous crystal structures that exist in liquid-solid regions is simulated through the use of a momentum resistance source term. (Abstract shortened by UMI.)

Recent trends in aviation turbine fuel properties

NASA Technical Reports Server (NTRS)

Friedman, R.

1982-01-01

Plots and tables, compiled from Department of Energy (and predecessor agency) inspection reports from 1969 to 1980, present ranges, averages, extremes, and trends for most of the 22 properties of Jet A aviation turbine fuel. In recent years, average values of aromatics content, mercaptan sulfur content, distillation temperature of 10 percent recovered, smoke point, and freezing point show small but recognizable trends toward their specification limits. About 80 percent of the fuel samples had at least one property near specification, defined as within a standard band about the specification limit. By far the most common near-specification properties were aromatics content, smoke point, and freezing point.

Method for cold stable biojet fuel

DOEpatents

Seames, Wayne S.; Aulich, Ted

2015-12-08

Plant or animal oils are processed to produce a fuel that operates at very cold temperatures and is suitable as an aviation turbine fuel, a diesel fuel, a fuel blendstock, or any fuel having a low cloud point, pour point or freeze point. The process is based on the cracking of plant or animal oils or their associated esters, known as biodiesel, to generate lighter chemical compounds that have substantially lower cloud, pour, and/or freeze points than the original oil or biodiesel. Cracked oil is processed using separation steps together with analysis to collect fractions with desired low temperature properties by removing undesirable compounds that do not possess the desired temperature properties.

Hepatitis B vaccine freezing in the Indonesian cold chain: evidence and solutions.

PubMed

Nelson, Carib M; Wibisono, Hariadi; Purwanto, Hary; Mansyur, Isa; Moniaga, Vanda; Widjaya, Anton

2004-02-01

To document and characterize freezing temperatures in the Indonesian vaccine cold chain and to evaluate the feasibility of changes designed to reduce the occurrence of freezing. Data loggers were used to measure temperatures of shipments of hepatitis B vaccine from manufacturer to point of use. Baseline conditions and three intervention phases were monitored. During each of the intervention phases, vaccines were removed progressively from the standard 2-8 degrees C cold chain. Freezing temperatures were recorded in 75% of baseline shipments. The highest rates of freezing occurred during transport from province to district, storage in district-level ice-lined refrigerators, and storage in refrigerators in health centres. Interventions reduced freezing, without excessive heat exposure. Inadvertent freezing of freeze-sensitive vaccines is widespread in Indonesia. Simple strategies exist to reduce freezing - for example, selective transport and storage of vaccines at ambient temperatures. The use of vaccine vial monitors reduces the risk associated with heat-damaged vaccines in these scenarios. Policy changes that allow limited storage of freeze-sensitive vaccines at temperatures >2-8 degrees C would enable flexible vaccine distribution strategies that could reduce vaccine freezing, reduce costs, and increase capacity.

Two-dimensional freezing criteria for crystallizing colloidal monolayers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang Ziren; Han Yilong; Alsayed, Ahmed M.

Video microscopy was employed to explore crystallization of colloidal monolayers composed of diameter-tunable microgel spheres. Two-dimensional (2D) colloidal liquids were frozen homogenously into polycrystalline solids, and four 2D criteria for freezing were experimentally tested in thermal systems for the first time: the Hansen-Verlet freezing rule, the Loewen-Palberg-Simon dynamical freezing criterion, and two other rules based, respectively, on the split shoulder of the radial distribution function and on the distribution of the shape factor of Voronoi polygons. Importantly, these freezing criteria, usually applied in the context of single crystals, were demonstrated to apply to the formation of polycrystalline solids. At themore » freezing point, we also observed a peak in the fluctuations of the orientational order parameter and a percolation transition associated with caged particles. Speculation about these percolated clusters of caged particles casts light on solidification mechanisms and dynamic heterogeneity in freezing.« less

Spacecraft Radiator Freeze Protection Using a Regenerative Heat Exchanger with Bypass Setpoint Temperature Control

NASA Technical Reports Server (NTRS)

Ungar, Eugene K.

2008-01-01

Spacecraft radiators are sized for their maximum heat load in their warmest thermal environment, but must operate at reduced heat loads and in colder environments. For systems where the radiator environment can be colder than the working fluid freezing temperature, radiator freezing becomes an issue. Radiator freezing has not been a major issue for the Space Shuttle and the International Space Station (ISS) active thermal control systems (ATCSs) because they operate in environments that are warm relative to the freezing point of their external coolants (Freon-21 and ammonia, respectively). For a vehicle that lands at the Lunar South Pole, the design thermal environment is 215K, but the radiator working fluid must also be kept from freezing during the 0 K sink of transit. A radiator bypass flow control design such as those used on the Space Shuttle and ISS requires more than 30% of the design heat load to avoid radiator freezing during transit - even with a very low freezing point working fluid. By changing the traditional ATCS architecture to include a regenerating heat exchanger inboard of the radiator and by using a regenerator bypass flow control valve to maintain system setpoint, the required minimum heat load can be reduced by more than half. This gives the spacecraft much more flexibility in design and operation. The present work describes the regenerator bypass ATCS setpoint control methodology. It includes analytical results comparing the performance of this system to the traditional radiator bypass system. Finally, a summary of the advantages of the regenerator bypass system are presented.

Ice nucleation and antinucleation in nature.

PubMed

Zachariassen, K E; Kristiansen, E

2000-12-01

Plants and ectothermic animals use a variety of substances and mechanisms to survive exposure to subfreezing temperatures. Proteinaceous ice nucleators trigger freezing at high subzero temperatures, either to provide cold protection from released heat of fusion or to establish a protective extracellular freezing in freeze-tolerant species. Freeze-avoiding species increase their supercooling potential by removing ice nucleators and accumulating polyols. Terrestrial invertebrates and polar marine fish stabilize their supercooled state by means of noncolligatively acting antifreeze proteins. Some organisms also depress their body fluid melting point to ambient temperature by evaporation and/or solute accumulation. Copyright 2000 Academic Press.

Progress in Noise Thermometry at 505 K and 693 K Using Quantized Voltage Noise Ratio Spectra

NASA Astrophysics Data System (ADS)

Tew, W. L.; Benz, S. P.; Dresselhaus, P. D.; Coakley, K. J.; Rogalla, H.; White, D. R.; Labenski, J. R.

2010-09-01

Technical advances and new results in noise thermometry at temperatures near the tin freezing point and the zinc freezing point using a quantized voltage noise source (QVNS) are reported. The temperatures are derived by comparing the power spectral density of QVNS synthesized noise with that of Johnson noise from a known resistance at both 505 K and 693 K. Reference noise is digitally synthesized so that the average power spectra of the QVNS match those of the thermal noise, resulting in ratios of power spectra close to unity in the low-frequency limit. Three-parameter models are used to account for differences in impedance-related time constants in the spectra. Direct comparison of noise temperatures to the International Temperature Scale of 1990 (ITS-90) is achieved in a comparison furnace with standard platinum resistance thermometers. The observed noise temperatures determined by operating the noise thermometer in both absolute and relative modes, and related statistics together with estimated uncertainties are reported. The relative noise thermometry results are combined with results from other thermodynamic determinations at temperatures near the tin freezing point to calculate a value of T - T 90 = +4(18) mK for temperatures near the zinc freezing point. These latest results achieve a lower uncertainty than that of our earlier efforts. The present value of T - T 90 is compared to other published determinations from noise thermometry and other methods.

Freezing curve-based monitoring to quickly evaluate the viability of biological materials subject to freezing or thermal injury.

PubMed

Liu, Jing; Zhou, Yi-Xin

2003-09-01

This paper is aimed at investigating the roles of freezing dynamics of a liquid droplet to characterize the properties of the material. In particular, freezing curve-based monitoring was proposed to quickly evaluate the viability of biological materials subject to freezing, re-warming, or other kinds of injury, which is an extremely important issue in practices such as cryobiology, hyperthermia, or freshness evaluation of bio-samples. An integrated micro analysis device was fabricated which is simple in structure and cheap to make. Preliminary freezing results demonstrated that minor changes in a biological material due to freezing or warming injury might result in a significant deviation of its freezing curve from that of the intact biomaterials. Several potential thermal indexes to quantify the material features were pointed out. Further, experiments were performed on some freezing and thawing processes of small amount of water on a cooling surface to test the effects of droplet sizes, measurement sites, cooling strength, and cooling geometry, etc., on the freezing responses of a water droplet. Their implementation in developing a new micro analysis system were suggested. This freezing curve-based monitoring method may open a new strategy for the evaluation of biomaterials subject to destruction in diverse fields.

Evaluation of Heat Flux Measurement as a New Process Analytical Technology Monitoring Tool in Freeze Drying.

PubMed

Vollrath, Ilona; Pauli, Victoria; Friess, Wolfgang; Freitag, Angelika; Hawe, Andrea; Winter, Gerhard

2017-05-01

This study investigates the suitability of heat flux measurement as a new technique for monitoring product temperature and critical end points during freeze drying. The heat flux sensor is tightly mounted on the shelf and measures non-invasively (no contact with the product) the heat transferred from shelf to vial. Heat flux data were compared to comparative pressure measurement, thermocouple readings, and Karl Fischer titration as current state of the art monitoring techniques. The whole freeze drying process including freezing (both by ramp freezing and controlled nucleation) and primary and secondary drying was considered. We found that direct measurement of the transferred heat enables more insights into thermodynamics of the freezing process. Furthermore, a vial heat transfer coefficient can be calculated from heat flux data, which ultimately provides a non-invasive method to monitor product temperature throughout primary drying. The end point of primary drying determined by heat flux measurements was in accordance with the one defined by thermocouples. During secondary drying, heat flux measurements could not indicate the progress of drying as monitoring the residual moisture content. In conclusion, heat flux measurements are a promising new non-invasive tool for lyophilization process monitoring and development using energy transfer as a control parameter. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Point-of-injury Use of Reconstituted Freeze Dried Plasma as a Resuscitative Fluid: A Special Report for Prehospital Trauma Care

DTIC Science & Technology

2013-01-01

Point-of-injury use of reconstituted freeze dried plasma as a resuscitative fluid: A special report for prehospital trauma care Elon Glassberg, MD...in- jury as part of the multidisciplinary efforts to improve trauma victims’ outcome. BACKGROUND Trauma is the leading cause of death among adults be...diabetes.1 Managing the burden of injuries from decades of wars has underscored the importance of trauma research aimed at reducing morbidity and

Coincidence probability as a measure of the average phase-space density at freeze-out

NASA Astrophysics Data System (ADS)

Bialas, A.; Czyz, W.; Zalewski, K.

2006-02-01

It is pointed out that the average semi-inclusive particle phase-space density at freeze-out can be determined from the coincidence probability of the events observed in multiparticle production. The method of measurement is described and its accuracy examined.

Moments of the Particle Phase-Space Density at Freeze-out and Coincidence Probabilities

NASA Astrophysics Data System (ADS)

Bialas, A.; Czyż, W.; Zalewski, K.

2005-10-01

It is pointed out that the moments of phase-space particle density at freeze-out can be determined from the coincidence probabilities of the events observed in multiparticle production. A method to measure the coincidence probabilities is described and its validity examined.

Determination of end point of primary drying in freeze-drying process control.

PubMed

Patel, Sajal M; Doen, Takayuki; Pikal, Michael J

2010-03-01

Freeze-drying is a relatively expensive process requiring long processing time, and hence one of the key objectives during freeze-drying process development is to minimize the primary drying time, which is the longest of the three steps in freeze-drying. However, increasing the shelf temperature into secondary drying before all of the ice is removed from the product will likely cause collapse or eutectic melt. Thus, from product quality as well as process economics standpoint, it is very critical to detect the end of primary drying. Experiments were conducted with 5% mannitol and 5% sucrose as model systems. The apparent end point of primary drying was determined by comparative pressure measurement (i.e., Pirani vs. MKS Baratron), dew point, Lyotrack (gas plasma spectroscopy), water concentration from tunable diode laser absorption spectroscopy, condenser pressure, pressure rise test (manometric temperature measurement or variations of this method), and product thermocouples. Vials were pulled out from the drying chamber using a sample thief during late primary and early secondary drying to determine percent residual moisture either gravimetrically or by Karl Fischer, and the cake structure was determined visually for melt-back, collapse, and retention of cake structure at the apparent end point of primary drying (i.e., onset, midpoint, and offset). By far, the Pirani is the best choice of the methods tested for evaluation of the end point of primary drying. Also, it is a batch technique, which is cheap, steam sterilizable, and easy to install without requiring any modification to the existing dryer.

Effects of egg yolk, glycerol and the freezing rate on the viability and acrosomal structures of frozen ram spermatozoa.

PubMed

Watson, P F; Martin, I C

1975-04-01

The influence of egg yolk, glycerol and the freezing rate on the survival of ram spermatozoa and on the structure of their acrosomes after freezing was investigated. Egg yolk was shown to be beneficial not only during chilling but also during freezing; of the levels examined, 1-5% gave the greatest protection. Although the presence of glycerol in the diluent improved the survival of spermatozoa, increasing concentrations produced significant deterioration of the acrosomes. With closely controlled linear cooling rates, no overall difference was detected in the survival of spermatozoa frozen at rates between 6 and 24 degrees C per min. However, a significant interaction between freezing rate and the inclusion of glycerol in the diluent showed that glycerol was less important at the highest freezing rate. A sudden cooling phase near to the freezing point following the release of the latent heat of fusion was not detrimental to spermatozoa.

Locating the QCD critical end point through peaked baryon number susceptibilities along the freeze-out line

NASA Astrophysics Data System (ADS)

Li, Zhibin; Chen, Yidian; Li, Danning; Huang, Mei

2018-01-01

We investigate the baryon number susceptibilities up to fourth order along different freeze-out lines in a holographic QCD model with a critical end point (CEP), and we propose that the peaked baryon number susceptibilities along the freeze-out line can be used as a clean signature to locate the CEP in the QCD phase diagram. On the temperature and baryon chemical potential plane, the cumulant ratio of the baryon number susceptibilities (up to fourth order) forms a ridge along the phase boundary, and develops a sword-shaped “mountain” standing upright around the CEP in a narrow and oblate region. The measurement of baryon number susceptibilities from heavy-ion collision experiments is along the freeze-out line. If the freeze-out line crosses the foot of the CEP mountain, then one can observe the peaked baryon number susceptibilities along the freeze-out line, and the kurtosis of the baryon number distributions has the highest magnitude. The data from the first phase of the beam energy scan program at the Relativistic Heavy Ion Collider indicates that there should be a peak of the kurtosis of the baryon number distribution at a collision energy of around 5 GeV, which suggests that the freeze-out line crosses the foot of the CEP mountain and the summit of the CEP should be located nearby, around a collision energy of 3-7 GeV. Supported by NSFC (11275213, and 11261130311) (CRC 110 by DFG and NSFC), CAS key project KJCX2-EW-N01, and Youth Innovation Promotion Association of CAS

Care during freeze-drying of bovine pericardium tissue to be used as a biomaterial: a comparative study.

PubMed

Polak, Roberta; Pitombo, Ronaldo N M

2011-10-01

Bovine pericardium (BP) tissue is widely used in the manufacture of bioprosthetics. The effects of freeze-drying on the BP tissue have been studied by some researchers in order to decrease their cytotoxicity due to preservation in formaldehyde solution, and to increase the lifetime of the product in storage. This study was undertaken in order to study the effect of freeze-drying in the structure of BP. To perform this study BP samples were freeze-dried in two different types of freeze-dryers available in our laboratory: a laboratory freeze-dryer, in which it was not possible to control parameters and a pilot freeze-dryer, wherein all parameters during freezing and drying were controlled. After freeze-drying processes, samples were analyzed by SEM, Raman spectroscopy, tensile strength, water uptake tests and TEM. In summary, it has been demonstrated that damages occur in collagen fibers by the loss of bulk water of collagen structure implicating in a drastic decreasing of BP mechanical properties due to its structural alterations. Moreover, it was proven that the collagen fibrils suffered breakage at some points, which can be attributed to the uncontrolled parameters during drying. Copyright © 2011 Elsevier Inc. All rights reserved.

Nature and morphology of fumed oxides and features of interfacial phenomena

NASA Astrophysics Data System (ADS)

Gun'ko, V. M.; Zarko, V. I.; Goncharuk, O. V.; Matkovsky, A. K.; Remez, O. S.; Skubiszewska-Zięba, J.; Wojcik, G.; Walusiak, B.; Blitz, J. P.

2016-03-01

Individual and complex fumed nanooxides were studied using high-resolution transmission electron microscopy, X-ray diffraction, ultraviolet-visible (UV-vis) spectroscopy, differential scanning calorimetry, nuclear magnetic resonance spectroscopy, adsorption, desorption (evaporation), and quantum chemical methods. For mixed nanooxides in contrast to simple and small nanoparticles of individual silica or titania, complex core-shell nanoparticles (50-200 nm in size) with titania or alumina cores and silica or alumina shells can be destroyed under high-pressure cryogelation (HPCG), mechnochemical activation (MCA) that also affect the structure of aggregates of nanoparticles and agglomerates of aggregates becoming more compacted. This is accompanied by changes in color from white to beige of different tints and changes in the UV-vis spectra in the 300-600 nm range, as well as changes in crystalline structure of alumina. Any treatment of 'soft' nanooxides affects the interfacial behavior of polar and nonpolar adsorbates. For some of them, the hysteresis loops become strongly open. Rearrangement of secondary particles affects the freezing-melting point depression. Clusterization of adsorbates bound in pores causes diminution of heat effects during phase transition (freezing, fusion). Freezing point depression and increasing melting point cause significant hysteresis freezing-melting effects for adsorbates bound to oxide nanoparticles. The study shows that complex nanooxides can be more sensitive to external actions than simple nanooxides such as silica.

Experimental Study of Low Temperature Behavior of Aviation Turbine Fuels in a Wing Tank Model

NASA Technical Reports Server (NTRS)

Stockemer, Francis J.

1979-01-01

An experimental investigation was performed to study aircraft fuels at low temperatures near the freezing point. The objective was an improved understanding of the flowability and pumpability of the fuels under conditions encoutered during cold weather flight of a long range commercial aircraft. The test tank simulated a section of an outer wing tank and was chilled on the upper and lower surfaces. Fuels included commercial Jet A and Diesel D-2; JP-5 from oil shale; and Jet A, intermediate freeze point, and D-2 fuels derived from selected paraffinic and naphthenic crudes. A pour point depressant was tested.

Teaching Process Engineering Principles Using an Ice Cream Maker

ERIC Educational Resources Information Center

Kaletunc, Gonul; Duemmel, Kevin; Gecik, Christopher

2007-01-01

The ice cream laboratory experiment is designed to illustrate and promote discussion of several engineering and science topics including material and energy balances, heat transfer, freezing, mass transfer, mixing, viscosity, and freezing point depression in a sophomore level engineering class. A pre-lab assignment requires the students to develop…

Origin of melting point depression for rare gas solids confined in carbon pores

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morishige, Kunimitsu, E-mail: morishi@chem.ous.ac.jp; Kataoka, Takaaki

To obtain insights into the mechanism of the melting-point depression of rare gas solids confined in crystalline carbon pores, we examined the freezing and melting behavior of Xe and Ar confined to the crystalline pores of ordered mesoporous carbons as well as compressed exfoliated graphite compared to the amorphous pores of ordered mesoporous silicas, by means of X-ray diffraction. For the Xe and Ar confined to the crystalline carbon pores, there was no appreciable thermal hysteresis between freezing and melting. Furthermore, the position of the main diffraction peak did not change appreciably on freezing and melting. This strongly suggests thatmore » the liquids confined in the carbon pores form a multilayered structure parallel to the smooth walls. For the Xe and Ar confined to the amorphous silica pores, on the other hand, the position of the main diffraction peak shifted into higher scattering angle on freezing suggested that the density of the confined solid is distinctly larger than for the confined liquid. Using compressed exfoliated graphite with carbon walls of higher crystallinity, we observed that three-dimensional (3D) microcrystals of Xe confined in the slit-shaped pores melted to leave the unmelted bilayers on the pore walls below the bulk triple point. The lattice spacing of the 3D microcrystals confined is larger by ∼0.7% than that of the bilayer next to the pore walls in the vicinity of the melting point.« less

Freezing points and small-scale deicing tests for salts of levulinic acid made from grain sorghum.

PubMed

Ganjyal, G; Fang, Q; Hanna, M A

2007-11-01

Deicers from renewable resources are needed to overcome the disadvantages of using traditional deicers. Salts made from levulinic acid produced using grain sorghum as raw material were tested as road deicing agents. Freezing points of these salts viz., sodium levulinate, magnesium levulinate and calcium levulinate along with rock salt (sodium chloride) were determined according to American Society for Testing and Materials (ASTM) D 1177-94 standard at concentrations of 10, 20, 30 and 40 % w/w. There were significant differences among the freezing points of the salts. Freezing points for rock salt, sodium levulinate, calcium levulinate and magnesium levulinate, for different concentrations, were in the ranges of -6.6 to -20.5, -2.9 to -15.0, -2.1 to -7.8 and -1.5 to -6.5 degrees C, respectively. Deicing effectiveness of the salts of levulinic acid were investigated by conducting small-scale deicing tests with aqueous solutions of various salt concentrations (2%, 5% and 10%) in a laboratory freezer and by spraying the deicer on a graveled surface covered by ice and snow with the average temperature during the testing at -2.7 degrees C. Deicing capabilities of the three salts of levulinic acid differed. At -2.7 degrees C, all three salts caused melting of the ice. Among the different levulinates studied sodium levulinate was the most effective deicing agent. These salts of levulinates could be a viable replacement for traditional deicers and could help in reducing the disadvantages of traditional deicers.

Ice-Binding Proteins in Plants

PubMed Central

Bredow, Melissa; Walker, Virginia K.

2017-01-01

Sub-zero temperatures put plants at risk of damage associated with the formation of ice crystals in the apoplast. Some freeze-tolerant plants mitigate this risk by expressing ice-binding proteins (IBPs), that adsorb to ice crystals and modify their growth. IBPs are found across several biological kingdoms, with their ice-binding activity and function uniquely suited to the lifestyle they have evolved to protect, be it in fishes, insects or plants. While IBPs from freeze-avoidant species significantly depress the freezing point, plant IBPs typically have a reduced ability to lower the freezing temperature. Nevertheless, they have a superior ability to inhibit the recrystallization of formed ice. This latter activity prevents ice crystals from growing larger at temperatures close to melting. Attempts to engineer frost-hardy plants by the controlled transfer of IBPs from freeze-avoiding fish and insects have been largely unsuccessful. In contrast, the expression of recombinant IBP sequences from freeze-tolerant plants significantly reduced electrolyte leakage and enhanced freezing survival in freeze-sensitive plants. These promising results have spurred additional investigations into plant IBP localization and post-translational modifications, as well as a re-evaluation of IBPs as part of the anti-stress and anti-pathogen axis of freeze-tolerant plants. Here we present an overview of plant freezing stress and adaptation mechanisms and discuss the potential utility of IBPs for the generation of freeze-tolerant crops. PMID:29312400

Ice-Binding Proteins in Plants.

PubMed

Bredow, Melissa; Walker, Virginia K

2017-01-01

Sub-zero temperatures put plants at risk of damage associated with the formation of ice crystals in the apoplast. Some freeze-tolerant plants mitigate this risk by expressing ice-binding proteins (IBPs), that adsorb to ice crystals and modify their growth. IBPs are found across several biological kingdoms, with their ice-binding activity and function uniquely suited to the lifestyle they have evolved to protect, be it in fishes, insects or plants. While IBPs from freeze-avoidant species significantly depress the freezing point, plant IBPs typically have a reduced ability to lower the freezing temperature. Nevertheless, they have a superior ability to inhibit the recrystallization of formed ice. This latter activity prevents ice crystals from growing larger at temperatures close to melting. Attempts to engineer frost-hardy plants by the controlled transfer of IBPs from freeze-avoiding fish and insects have been largely unsuccessful. In contrast, the expression of recombinant IBP sequences from freeze-tolerant plants significantly reduced electrolyte leakage and enhanced freezing survival in freeze-sensitive plants. These promising results have spurred additional investigations into plant IBP localization and post-translational modifications, as well as a re-evaluation of IBPs as part of the anti-stress and anti-pathogen axis of freeze-tolerant plants. Here we present an overview of plant freezing stress and adaptation mechanisms and discuss the potential utility of IBPs for the generation of freeze-tolerant crops.

Optimization of the secondary drying step in freeze drying using TDLAS technology.

PubMed

Schneid, Stefan C; Gieseler, Henning; Kessler, William J; Luthra, Suman A; Pikal, Michael J

2011-03-01

The secondary drying phase in freeze drying is mostly developed on a trial-and-error basis due to the lack of appropriate noninvasive process analyzers. This study describes for the first time the application of Tunable Diode Laser Absorption Spectroscopy, a spectroscopic and noninvasive sensor for monitoring secondary drying in laboratory-scale freeze drying with the overall purpose of targeting intermediate moisture contents in the product. Bovine serum albumin/sucrose mixtures were used as a model system to imitate high concentrated antibody formulations. First, the rate of water desorption during secondary drying at constant product temperatures (-22 °C, -10 °C, and 0 °C) was investigated for three different shelf temperatures. Residual moisture contents of sampled vials were determined by Karl Fischer titration. An equilibration step was implemented to ensure homogeneous distribution of moisture (within 1%) in all vials. The residual moisture revealed a linear relationship to the water desorption rate for different temperatures, allowing the evaluation of an anchor point from noninvasive flow rate measurements without removal of samples from the freeze dryer. The accuracy of mass flow integration from this anchor point was found to be about 0.5%. In a second step, the concept was successfully tested in a confirmation experiment. Here, good agreement was found for the initial moisture content (anchor point) and the subsequent monitoring and targeting of intermediate moisture contents. The present approach for monitoring secondary drying indicated great potential to find wider application in sterile operations on production scale in pharmaceutical freeze drying. © 2011 American Association of Pharmaceutical Scientists

Close-packed floating clusters: granular hydrodynamics beyond the freezing point?

PubMed

Meerson, Baruch; Pöschel, Thorsten; Bromberg, Yaron

2003-07-11

Monodisperse granular flows often develop regions with hexagonal close packing of particles. We investigate this effect in a system of inelastic hard spheres driven from below by a "thermal" plate. Molecular dynamics simulations show, in a wide range of parameters, a close-packed cluster supported by a low-density region. Surprisingly, the steady-state density profile, including the close-packed cluster part, is well described by a variant of Navier-Stokes granular hydrodynamics (NSGH). We suggest a simple explanation for the success of NSGH beyond the freezing point.

A systematic evaluation of contemporary impurity correction methods in ITS-90 aluminium fixed point cells

NASA Astrophysics Data System (ADS)

da Silva, Rodrigo; Pearce, Jonathan V.; Machin, Graham

2017-06-01

The fixed points of the International Temperature Scale of 1990 (ITS-90) are the basis of the calibration of standard platinum resistance thermometers (SPRTs). Impurities in the fixed point material at the level of parts per million can give rise to an elevation or depression of the fixed point temperature of order of millikelvins, which often represents the most significant contribution to the uncertainty of SPRT calibrations. A number of methods for correcting for the effect of impurities have been advocated, but it is becoming increasingly evident that no single method can be used in isolation. In this investigation, a suite of five aluminium fixed point cells (defined ITS-90 freezing temperature 660.323 °C) have been constructed, each cell using metal sourced from a different supplier. The five cells have very different levels and types of impurities. For each cell, chemical assays based on the glow discharge mass spectroscopy (GDMS) technique have been obtained from three separate laboratories. In addition a series of high quality, long duration freezing curves have been obtained for each cell, using three different high quality SPRTs, all measured under nominally identical conditions. The set of GDMS analyses and freezing curves were then used to compare the different proposed impurity correction methods. It was found that the most consistent corrections were obtained with a hybrid correction method based on the sum of individual estimates (SIE) and overall maximum estimate (OME), namely the SIE/Modified-OME method. Also highly consistent was the correction technique based on fitting a Scheil solidification model to the measured freezing curves, provided certain well defined constraints are applied. Importantly, the most consistent methods are those which do not depend significantly on the chemical assay.

Fabrication of a mini multi-fixed-point cell for the calibration of industrial platinum resistance thermometers

NASA Astrophysics Data System (ADS)

Ragay-Enot, Monalisa; Lee, Young Hee; Kim, Yong-Gyoo

2017-07-01

A mini multi-fixed-point cell (length 118 mm, diameter 33 mm) containing three materials (In-Zn eutectic (mass fraction 3.8% Zn), Sn and Pb) in a single crucible was designed and fabricated for the easy and economical fixed-point calibration of industrial platinum resistance thermometers (IPRTs) for use in industrial temperature measurements. The melting and freezing behaviors of the metals were investigated and the phase transition temperatures were determined using a commercial dry-block calibrator. Results showed that the melting plateaus are generally easy to realize and are reproducible, flatter and of longer duration. On the other hand, the freezing process is generally difficult, especially for Sn, due to the high supercooling required to initiate freezing. The observed melting temperatures at optimum set conditions were 143.11 °C (In-Zn), 231.70 °C (Sn) and 327.15 °C (Pb) with expanded uncertainties (k  = 2) of 0.12 °C, 0.10 °C and 0.13 °C, respectively. This multi-fixed-point cell can be treated as a sole reference temperature-generating system. Based on the results, the realization of melting points of the mini multi-fixed-point cell can be recommended for the direct calibration of IPRTs in industrial applications without the need for a reference thermometer.

Influence of the freezing method on the changes that occur in grape samples after frozen storage.

PubMed

Santesteban, Luis G; Miranda, Carlos; Royo, José B

2013-09-01

Sample freezing is frequently used in oenological laboratories as a compromise solution to increase the number of samples that can be analysed, despite the fact that some grape characteristics are known to change after frozen storage. However, freezing is usually performed using standard freezers, which provide a slow freezing. The aim of this work was to evaluate whether blast freezing would decrease the impact of standard freezing on grape composition. Grape quality parameters were assessed in fresh and in frozen stored samples that had been frozen using three different procedures: standard freezing and blast freezing using either a blast freezer or an ultra-freezer. The implications of frozen storage in grape samples reported in earlier research were observed for the three freezing methods evaluated. Although blast freezing improved repeatability for the most problematic parameters (tartaric acidity, TarA; total phenolics, TP), the improvement was not important from a practical point of view. However, TarA and TP were relatively repeatable among the three freezing procedures, which suggests that freezing had an effect on these parameters independently of the method used . According to our results, the salification potential of the must is probably implied in the changes observed for TarA, whereas for TP the precipitation of protoanthocyanins after association with cell wall material is hypothesized to cause the lack of repeatability between fresh and frozen grapes. Blast freezing would not imply a great improvement if implemented in oenological laboratories, at least for the parameters included in this study. © 2013 Society of Chemical Industry.

Ultra-high temperature isothermal furnace liners (IFLS) for copper freeze point cells

NASA Astrophysics Data System (ADS)

Dussinger, P. M.; Tavener, J. P.

2013-09-01

Primary Laboratories use large fixed-point cells in deep calibration furnaces utilizing heat pipes to achieve temperature uniformity. This combination of furnace, heat pipe, and cell gives the smallest of uncertainties. The heat pipe, also known as an isothermal furnace liner (IFL), has typically been manufactured with Alloy 600/601 as the envelope material since the introduction of high temperature IFLs over 40 years ago. Alloy 600/601 is a widely available high temperature material, which is compatible with Cesium, Potassium, and Sodium and has adequate oxidation resistance and reasonable high temperature strength. Advanced Cooling Technologies, Inc. (ACT) Alloy 600/Sodium IFLs are rated to 1100°C for approximately 1000 hours of operation (based on creep strength). Laboratories interested in performing calibrations and studies around the copper freezing point (1084.62°C) were frustrated by the 1000 hours at 1100°C limitation and the fact that expensive freeze-point cells were getting stuck and/or crushed inside the IFL. Because of this growing frustration/need, ACT developed an Ultra High Temperature IFL to take advantage of the exceptional high temperature strength properties of Haynes 230.

Effects of high pressure freezing (HPF) on denaturation of natural actomyosin extracted from prawn (Metapenaeus ensis).

PubMed

Cheng, Lina; Sun, Da-Wen; Zhu, Zhiwei; Zhang, Zhihang

2017-08-15

Effects of protein denaturation caused by high pressure freezing, involving Pressure-Factors (pressure, time) and Freezing-Factors (temperature, phase transition, recrystallization, ice crystal types), are complicated. In the current study, the conformation and functional changes of natural actomyosin (NAM) under pressure assisted freezing (PAF, 100,150,300,400,500MPa P -20°C/25min ), pressure shift freezing (PSF, 200MPa P -20°C/25min ), and immersion freezing ( 0.1MPa P -20°C/5min ) after pressure was released to 0.1MPa, as compared to normal immersion freezing process (IF, 0.1MPa P -20°C/30min ). Results indicated that PSF ( 200MPa P -20°C/30min ) could reduce the denaturation of frozen NAM and a pressure of 300MPa was the critical point to induce such a denaturation. During the periods of B→D in PSF or B→C→D in PAF, the generation and growth of ice crystals played an important role on changing the secondary and tertiary structure of the treated NAM. Copyright © 2017 Elsevier Ltd. All rights reserved.

Linking ice accretion and crown structure: towards a model of the effect of freezing rain on tree canopies

PubMed Central

Nock, Charles A.; Lecigne, Bastien; Taugourdeau, Olivier; Greene, David F.; Dauzat, Jean; Delagrange, Sylvain; Messier, Christian

2016-01-01

Background and Aims Despite a longstanding interest in variation in tree species vulnerability to ice storm damage, quantitative analyses of the influence of crown structure on within-crown variation in ice accretion are rare. In particular, the effect of prior interception by higher branches on lower branch accumulation remains unstudied. The aim of this study was to test the hypothesis that intra-crown ice accretion can be predicted by a measure of the degree of sheltering by neighbouring branches. Methods Freezing rain was artificially applied to Acer platanoides L., and in situ branch-ice thickness was measured directly and from LiDAR point clouds. Two models of freezing rain interception were developed: ‘IceCube’, which uses point clouds to relate ice accretion to a voxel-based index (sheltering factor; SF) of the sheltering effect of branch elements above a measurement point; and ‘IceTree’, a simulation model for in silico evaluation of the interception pattern of freezing rain in virtual tree crowns. Key Results Intra-crown radial ice accretion varied strongly, declining from the tips to the bases of branches and from the top to the base of the crown. SF for branches varied strongly within the crown, and differences among branches were consistent for a range of model parameters. Intra-crown variation in ice accretion on branches was related to SF (R2 = 0·46), with in silico results from IceTree supporting empirical relationships from IceCube. Conclusions Empirical results and simulations confirmed a key role for crown architecture in determining intra-crown patterns of ice accretion. As suspected, the concentration of freezing rain droplets is attenuated by passage through the upper crown, and thus higher branches accumulate more ice than lower branches. This is the first step in developing a model that can provide a quantitative basis for investigating intra-crown and inter-specific variation in freezing rain damage. PMID:27107412

Determining osmotic pressure of drug solutions by air humidity in equilibrium method.

PubMed

Zhan, Xiancheng; Li, Hui; Yu, Lan; Wei, Guocui; Li, Chengrong

2014-06-01

To establish a new osmotic pressure measuring method with a wide measuring range. The osmotic pressure of drug solutions is determined by measuring the relative air humidity in equilibrium with the solution. The freezing point osmometry is used as a control. The data obtained by the proposed method are comparable to those by the control method, and the measuring range of the proposed method is significantly wider than that of the control method. The proposed method is performed in an isothermal and equilibrium state, so it overcomes the defects of the freezing point and dew point osmometries which result from the heterothermal process in the measurement, and therefore is not limited to diluted solutions.

Universal relations between non-Gaussian fluctuations in heavy-ion collisions

NASA Astrophysics Data System (ADS)

Chen, Jiunn-Wei; Deng, Jian; Kohyama, Hiroaki; Labun, Lance

2017-01-01

We show that universality near a critical end point implies a characteristic relation between third- and fourth-order baryon susceptibilities χ3 and χ4, resulting in a banana-shaped loop when χ4 is plotted as a function of χ3 along a freeze-out line. This result relies only on the derivative relation between χ3 and χ4, the enhancement of the correlation length and the scaling symmetry near a critical point, and the freeze-out line near the critical point not too parallel to the μB axis. Including the individual enhancements of χ3 and χ4 near a critical point, these features may be a consistent set of observations supporting the interpretation of baryon fluctuation data as arising from criticality.

On the GIBBS thermodynamic potential of seawater

NASA Astrophysics Data System (ADS)

Feistel, Rainer; Hagen, Eberhard

Free Enthalpy, the GIBBS thermodynamic potential G(S,t,p) of seawater, has been recomputed including the sound speed equation of DEL GROSSO (1974), temperatures of maximum density (TMD) of CALDWELL (1978), freezing point depression measurements of DOHERTY and KESTER (1974), rederived limiting laws and ice properties, and an extended set of dilution heat data of BROMLEY (1968) and MILLERO, HANSEN and HOFF (1973). As a new reference state, the standard ocean state has been chosen. The resulting average deviations are 0.0006 kg m -3 for pure water density at 1 atm, 0.002 kg m -3 for seawater density at 1 atm, 0.02 m/s for sound speed, 0.01 J kgK -1 for heat capacity at 1 atm, 0.4 kJ kg -1 for dilution heats, 0.002°C for freezing points, and 0.04°C for TMDs. Resulting pressure-dependent freezing points are in good agreement with experiments and UNESCO (1978) formulas. Enthalpy as thermodynamic potential has been explicitly determined for easy computation of potential temperature, potential density, and sound speed. All functions are expressed in the new International Temperature Scale ITS-90.

Ice Detector and Deicing Fluid Effectiveness Monitoring System

NASA Technical Reports Server (NTRS)

Seegmiller, H. Lee B. (Inventor)

1996-01-01

An ice detector and deicing fluid effectiveness monitoring system for an aircraft is disclosed. The ice detection portion is particularly suited for use in flight to notify the flight crew of an accumulation of ice on an aircraft lifting and control surfaces, or helicopter rotors, whereas the deicing fluid effectiveness monitoring portion is particularly suited for use on the ground to notify the flight crew of the possible loss of the effectiveness of the deicing fluid. The ice detection portion comprises a temperature sensor and a parallel arrangement of electrodes whose coefficient of coupling is indicative of the formation of the ice, as well as the thickness of the formed ice. The fluid effectiveness monitoring portion comprises a temperature sensor and an ionic-conduction cell array that measures the conductivity of the deicing fluid which is indicative of its concentration and, thus, its freezing point. By measuring the temperature and having knowledge of the freezing point of the deicing fluid, the fluid effectiveness monitoring portion predicts when the deicing fluid may lose its effectiveness because its freezing point may correspond to the temperature of the ambient.

Summer Freezing Resistance: A Critical Filter for Plant Community Assemblies in Mediterranean High Mountains

PubMed Central

Pescador, David S.; Sierra-Almeida, Ángela; Torres, Pablo J.; Escudero, Adrián

2016-01-01

Assessing freezing community response and whether freezing resistance is related to other functional traits is essential for understanding alpine community assemblages, particularly in Mediterranean environments where plants are exposed to freezing temperatures and summer droughts. Thus, we characterized the leaf freezing resistance of 42 plant species in 38 plots at Sierra de Guadarrama (Spain) by measuring their ice nucleation temperature, freezing point (FP), and low-temperature damage (LT50), as well as determining their freezing resistance mechanisms (i.e., tolerance or avoidance). The community response to freezing was estimated for each plot as community weighted means (CWMs) and functional diversity (FD), and we assessed their relative importance with altitude. We established the relationships between freezing resistance, growth forms, and four key plant functional traits (i.e., plant height, specific leaf area, leaf dry matter content (LDMC), and seed mass). There was a wide range of freezing resistance responses and more than in other alpine habitats. At the community level, the CWMs of FP and LT50 responded negatively to altitude, whereas the FD of both traits increased with altitude. The proportion of freezing-tolerant species also increased with altitude. The ranges of FP and LT50 varied among growth forms, and only leaf dry matter content was negatively correlated with freezing-resistance traits. Summer freezing events represent important abiotic filters for assemblies of Mediterranean high mountain communities, as suggested by the CWMs. However, a concomitant summer drought constraint may also explain the high freezing resistance of species that thrive in these areas and the lower FD of freezing resistance traits at lower altitudes. Leaves with high dry matter contents may maintain turgor at lower water potential and enhance drought tolerance in parallel to freezing resistance. This adaptation to drought seems to be a general prerequisite for plants found in xeric mountains. PMID:26941761

Neuropathy in non-freezing cold injury (trench foot).

PubMed Central

Irwin, M S; Sanders, R; Green, C J; Terenghi, G

1997-01-01

Non-freezing cold injury (trench foot) is characterized, in severe cases, by peripheral nerve damage and tissue necrosis. Controversy exists regarding the susceptibility of nerve fibre populations to injury as well as the mechanism of injury. Clinical and histological studies (n = 2) were conducted in a 40-year-old man with severe non-freezing cold injury in both feet. Clinical sensory tests, including two-point discrimination and pressure, vibration and thermal thresholds, indicated damage to large and small diameter nerves. On immunohistochemical assessment, terminal cutaneous nerve fibres within the plantar skin stained much less than in a normal control whereas staining to von Willebrand factor pointed to increased vascularity in all areas. The results indicate that all nerve populations (myelinated and unmyelinated) were damaged, possibly in a cycle of ischaemia and reperfusion. Images Figure 1 a Figure 1 b Figure 2 a Figure 2 b Figure 3 a Figure 3 b PMID:9306996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khrapak, Sergey A.; Joint Institute for High Temperatures, 125412 Moscow; Chaudhuri, Manis

We put forward an approximate method to locate the fluid-solid (freezing) phase transition in systems of classical particles interacting via a wide range of Lennard-Jones-type potentials. This method is based on the constancy of the properly normalized second derivative of the interaction potential (freezing indicator) along the freezing curve. As demonstrated recently it yields remarkably good agreement with previous numerical simulation studies of the conventional 12-6 Lennard-Jones (LJ) fluid [S.A.Khrapak, M.Chaudhuri, G.E.Morfill, Phys. Rev. B 134, 052101 (2010)]. In this paper, we test this approach using a wide range of the LJ-type potentials, including LJ n-6 and exp-6 models, andmore » find that it remains sufficiently accurate and reliable in reproducing the corresponding freezing curves, down to the triple-point temperatures. One of the possible application of the method--estimation of the freezing conditions in complex (dusty) plasmas with ''tunable'' interactions--is briefly discussed.« less

In situ study on atomic mechanism of melting and freezing of single bismuth nanoparticles

PubMed Central

Li, Yingxuan; Zang, Ling; Jacobs, Daniel L.; Zhao, Jie; Yue, Xiu; Wang, Chuanyi

2017-01-01

Experimental study of the atomic mechanism in melting and freezing processes remains a formidable challenge. We report herein on a unique material system that allows for in situ growth of bismuth nanoparticles from the precursor compound SrBi2Ta2O9 under an electron beam within a high-resolution transmission electron microscope (HRTEM). Simultaneously, the melting and freezing processes within the nanoparticles are triggered and imaged in real time by the HRTEM. The images show atomic-scale evidence for point defect induced melting, and a freezing mechanism mediated by crystallization of an intermediate ordered liquid. During the melting and freezing, the formation of nucleation precursors, nucleation and growth, and the relaxation of the system, are directly observed. Based on these observations, an interaction–relaxation model is developed towards understanding the microscopic mechanism of the phase transitions, highlighting the importance of cooperative multiscale processes. PMID:28194017

Microphysical Modelling of the 1999-2000 Arctic Winter. 3; Impact of Homogeneous Freezing on PSCs

NASA Technical Reports Server (NTRS)

Drdla, K.

2003-01-01

Simulations of the 1999-2000 winter have tested the effect on polar stratospheric clouds (PSCs) of the homogeneous freezing of liquid ternary solutions into nitric acid trihydrate (NAT) and nitric acid dihydrate (NAD). Proposed laboratory-derived volume-based and surface-based homogeneous freezing rates have both been examined, including different assumptions about the extrapolation of laboratory measurements to atmospheric conditions. Widespread PSC formation and denitrification are possible in several of the scenarios examined. However, the simulations are all unable to explain the solid-phase PSCs observed early in the 1999-2000 winter, and are unable to reproduce the measured extent of vortex denitrification. These problems can both be attributed to the relatively cold temperatures, more than 5 K below the NAT condensation point, necessary for effective homogeneous freezing. Therefore synoptic-scale homogeneous freezing appears unlikely to be the primary mechanism responsible for solid-phase PSC formation.

In situ study on atomic mechanism of melting and freezing of single bismuth nanoparticles

NASA Astrophysics Data System (ADS)

Li, Yingxuan; Zang, Ling; Jacobs, Daniel L.; Zhao, Jie; Yue, Xiu; Wang, Chuanyi

2017-02-01

Experimental study of the atomic mechanism in melting and freezing processes remains a formidable challenge. We report herein on a unique material system that allows for in situ growth of bismuth nanoparticles from the precursor compound SrBi2Ta2O9 under an electron beam within a high-resolution transmission electron microscope (HRTEM). Simultaneously, the melting and freezing processes within the nanoparticles are triggered and imaged in real time by the HRTEM. The images show atomic-scale evidence for point defect induced melting, and a freezing mechanism mediated by crystallization of an intermediate ordered liquid. During the melting and freezing, the formation of nucleation precursors, nucleation and growth, and the relaxation of the system, are directly observed. Based on these observations, an interaction-relaxation model is developed towards understanding the microscopic mechanism of the phase transitions, highlighting the importance of cooperative multiscale processes.

In situ study on atomic mechanism of melting and freezing of single bismuth nanoparticles.

PubMed

Li, Yingxuan; Zang, Ling; Jacobs, Daniel L; Zhao, Jie; Yue, Xiu; Wang, Chuanyi

2017-02-13

Experimental study of the atomic mechanism in melting and freezing processes remains a formidable challenge. We report herein on a unique material system that allows for in situ growth of bismuth nanoparticles from the precursor compound SrBi 2 Ta 2 O 9 under an electron beam within a high-resolution transmission electron microscope (HRTEM). Simultaneously, the melting and freezing processes within the nanoparticles are triggered and imaged in real time by the HRTEM. The images show atomic-scale evidence for point defect induced melting, and a freezing mechanism mediated by crystallization of an intermediate ordered liquid. During the melting and freezing, the formation of nucleation precursors, nucleation and growth, and the relaxation of the system, are directly observed. Based on these observations, an interaction-relaxation model is developed towards understanding the microscopic mechanism of the phase transitions, highlighting the importance of cooperative multiscale processes.

Homogeneous freezing of single sulfuric and nitric acid solution drops levitated in an acoustic trap

NASA Astrophysics Data System (ADS)

Diehl, Karoline; Ettner-Mahl, Matthias; Hannemann, Anke; Mitra, Subir K.

2009-10-01

The freezing temperatures of single supercooled drops of binary and ternary sulfuric and nitric acid solutions were measured while varying the acid concentration. An acoustic levitator was used which allows to freely suspend single solution drops in air without electrical charges thereby avoiding any electrical influences which may affect the freezing process. The drops of typically 500 µm in radius were monitored by a video camera during cooling cycles down to - 85 °C to simulate the upper tropospheric and stratospheric temperature range. The present data confirm that liquid solution droplets can be supercooled far below the equilibrium melting point by approximately 35 °C. They follow the general trend of the expected freezing temperatures for homogeneous ice nucleation.

Effect of Impurities on the Freezing Point of Zinc

NASA Astrophysics Data System (ADS)

Sun, Jianping; Rudtsch, Steffen; Niu, Yalu; Zhang, Lin; Wang, Wei; Den, Xiaolong

2017-03-01

The knowledge of the liquidus slope of impurities in fixed-point metal defined by the International Temperature Scale of 1990 is important for the estimation of uncertainties and correction of fixed point with the sum of individual estimates method. Great attentions are paid to the effect of ultra-trace impurities on the freezing point of zinc in the National Institute of Metrology. In the present work, the liquidus slopes of Ga-Zn, Ge-Zn were measured with the slim fixed-point cell developed through the doping experiments, and the temperature characteristics of the phase diagram of Fe-Zn were furthermore investigated. A quasi-adiabatic Zn fixed-point cell was developed with the thermometer well surrounded by the crucible with the pure metal, and the temperature uniformity of less than 20 mK in the region where the metal is located was obtained. The previous doping experiment of Pb-Zn with slim fixed-point cell was checked with quasi-adiabatic Zn fixed-point cell, and the result supports the previous liquidus slope measured with the traditional fixed-point realization.

Exploring the Phenomenon of "Change of Phase" of Pure Substances Using the Microcomputer-Based-Laboratory (MBL) System

ERIC Educational Resources Information Center

Pierri, Evgenia; Karatrantou, Anthi; Panagiotakopoulos, Chris

2008-01-01

We examined how first year students (10th grade) of Greek Senior High School could conceptualize the influence of the molecular weight of saturated fatty acids on the melting and the freezing point, during the "change of phase" phenomenon using the Microcomputer-Based Laboratory (MBL) system. Students had to freeze a melted substance,…

Vapor Pressure Plus: An Experiment for Studying Phase Equilibria in Water, with Observation of Supercooling, Spontaneous Freezing, and the Triple Point

ERIC Educational Resources Information Center

Tellinghuisen, Joel

2010-01-01

Liquid-vapor, solid-vapor, and solid-liquid-vapor equilibria are studied for the pure substance water, using modern equipment that includes specially fabricated glass cells. Samples are evaporatively frozen initially, during which they typically supercool to -5 to -10 [degrees]C before spontaneously freezing. Vacuum pumping lowers the temperature…

40 CFR Appendix A to Subpart M of... - Interpretive Rule Governing Roof Removal Operations

Code of Federal Regulations, 2010 CFR

2010-07-01

...)). 3.B.3. An exemption from wetting is also allowed when the air or roof surface temperature at the point of wetting is below freezing, as specified in § 61.145(c)(7). If freezing temperatures are indicated as the reason for not wetting, records must be kept of the temperature at the beginning, middle...

Simulations of Polar Stratospheric Clouds and Denitrification Using Laboratory Freezing Rates

NASA Technical Reports Server (NTRS)

Drdla, Katja; Tabazadeh, Azadeh; Gore, Warren J. (Technical Monitor)

2001-01-01

During the 1999-2000 Arctic winter, the SAGE (Stratospheric Aerosol and Gas Experiment) III Ozone Loss and Validation Experiment (SOLVE) provided evidence of widespread solid-phase polar stratospheric clouds (PSCs) accompanied by severe nitrification. Previous simulations have shown that a freezing process occurring at temperatures above the ice frost point is necessary to explain these observations. In this work, the nitric acid freezing rates measured by Salcedo et al. and discussed by Tabazadeh et al. have been examined. These freezing rates have been tested in winter-long microphysical simulations of the 1999-2000 Arctic vortex evolution in order to determine whether they can explain the observations. A range of cases have been explored, including whether the PSC particles are composed of nitric acid dihydrate or trihydrate, whether the freezing process is a bulk process or occurs only on the particle surfaces, and uncertainties in the derived freezing rates. Finally, the possibility that meteoritic debris enhances the freezing rate has also been examined. The results of these simulations have been compared with key PSC and denitrification measurements made by the SOLVE campaign. The cases that best reproduce the measurements will he highlighted, with a discussion of the implications for our understanding of PSCs.

Ultrasonic emissions during ice nucleation and propagation in plant xylem.

PubMed

Charrier, Guillaume; Pramsohler, Manuel; Charra-Vaskou, Katline; Saudreau, Marc; Améglio, Thierry; Neuner, Gilbert; Mayr, Stefan

2015-08-01

Ultrasonic acoustic emission analysis enables nondestructive monitoring of damage in dehydrating or freezing plant xylem. We studied acoustic emissions (AE) in freezing stems during ice nucleation and propagation, by combining acoustic and infrared thermography techniques and controlling the ice nucleation point. Ultrasonic activity in freezing samples of Picea abies showed two distinct phases: the first on ice nucleation and propagation (up to 50 AE s(-1) ; reversely proportional to the distance to ice nucleation point), and the second (up to 2.5 AE s(-1) ) after dissipation of the exothermal heat. Identical patterns were observed in other conifer and angiosperm species. The complex AE patterns are explained by the low water potential of ice at the ice-liquid interface, which induced numerous and strong signals. Ice propagation velocities were estimated via AE (during the first phase) and infrared thermography. Acoustic activity ceased before the second phase probably because the exothermal heating and the volume expansion of ice caused decreasing tensions. Results indicate cavitation events at the ice front leading to AE. Ultrasonic emission analysis enabled new insights into the complex process of xylem freezing and might be used to monitor ice propagation in natura. © 2015 The Authors. New Phytologist © 2015 New Phytologist Trust.

Freeze drying for morphological control of inter-penetrating polymer networks

NASA Technical Reports Server (NTRS)

Hansen, Marion G.; Pater, Ruth H.

1990-01-01

The intrinsic brittleness of BMI resins can be reduced through the creation of an interpenetrating network (IPN) of BMI with a reactive-encapped thermoplastic, such as the presently considered polyimidesulfone, PISO2. The PISO2 and BMI were dissolved in a common solvent, which was then removed from the constituents by freeze drying; in an alternative method, an IPN was formed through dissolution of the constituent in a common solvent with either high or low melting point, followed by evaporative removal of the solvent. The effectiveness of the freeze-drying approach for morphological control is evaluated.

Comparison of actual vs synthesized ternary phase diagrams for solutes of cryobiological interest☆

PubMed Central

Kleinhans, F.W.; Mazur, Peter

2009-01-01

Phase diagrams are of great utility in cryobiology, especially those consisting of a cryoprotective agent (CPA) dissolved in a physiological salt solution. These ternary phase diagrams consist of plots of the freezing points of increasing concentrations of solutions of cryoprotective agents (CPA) plus NaCl. Because they are time-consuming to generate, ternary diagrams are only available for a small number of CPA's. We wanted to determine whether accurate ternary phase diagrams could be synthesized by adding together the freezing point depressions of binary solutions of CPA/water and NaCl/water which match the corresponding solute molality concentrations in the ternary solution. We begin with a low concentration of a solution of CPA + salt of given R (CPA/salt) weight ratio. Ice formation in that solution is mimicked by withdrawing water from it which increases the concentrations of both the CPA and the NaCl. We compute the individual solute concentrations, determine their freezing points from published binary phase diagrams, and sum the freezing points. These yield the synthesized ternary phase diagram for a solution of given R. They were compared with published experimental ternary phase diagrams for glycerol, dimethyl sulfoxide (DMSO), sucrose, and ethylene glycol (EG) plus NaCl in water. For the first three, the synthesized and experimental phase diagrams agreed closely, with some divergence occurring as wt % concentrations exceeded 30% for DMSO and 55% for glycerol and sucrose. However, in the case of EG there were substantial differences over nearly the entire range of concentrations which we attribute to systematic errors in the experimental EG data. New experimental EG work will be required to resolve this issue. PMID:17350609

Comparison of actual vs. synthesized ternary phase diagrams for solutes of cryobiological interest.

PubMed

Kleinhans, F W; Mazur, Peter

2007-04-01

Phase diagrams are of great utility in cryobiology, especially, those consisting of a cryoprotective agent (CPA) dissolved in a physiological salt solution. These ternary phase diagrams consist of plots of the freezing points of increasing concentrations of solutions of cryoprotective agents (CPA) plus NaCl. Because they are time-consuming to generate, ternary diagrams are only available for a small number of CPAs. We wanted to determine whether accurate ternary phase diagrams could be synthesized by adding together the freezing point depressions of binary solutions of CPA/water and NaCl/water which match the corresponding solute molality concentrations in the ternary solution. We begin with a low concentration of a solution of CPA+salt of given R (CPA/salt) weight ratio. Ice formation in that solution is mimicked by withdrawing water from it which increases the concentrations of both the CPA and the NaCl. We compute the individual solute concentrations, determine their freezing points from published binary phase diagrams, and sum the freezing points. These yield the synthesized ternary phase diagram for a solution of given R. They were compared with published experimental ternary phase diagrams for glycerol, dimethyl sulfoxide (DMSO), sucrose, and ethylene glycol (EG) plus NaCl in water. For the first three, the synthesized and experimental phase diagrams agreed closely, with some divergence occurring as wt% concentrations exceeded 30% for DMSO and 55% for glycerol, and sucrose. However, in the case of EG there were substantial differences over nearly the entire range of concentrations which we attribute to systematic errors in the experimental EG data. New experimental EG work will be required to resolve this issue.

Methane, Ethane, and Nitrogen Stability on Titan

NASA Astrophysics Data System (ADS)

Hanley, J.; Grundy, W. M.; Thompson, G.; Dustrud, S.; Pearce, L.; Lindberg, G.; Roe, H. G.; Tegler, S.

2017-12-01

Many outer solar system bodies are likely to have a combination of methane, ethane and nitrogen. In particular the lakes of Titan are known to consist of these species. Understanding the past and current stability of these lakes requires characterizing the interactions of methane and ethane, along with nitrogen, as both liquids and ices. Our cryogenic laboratory setup allows us to explore ices down to 30 K through imaging, and transmission and Raman spectroscopy. Our recent work has shown that although methane and ethane have similar freezing points, when mixed they can remain liquid down to 72 K. Concurrently with the freezing point measurements we acquire transmission or Raman spectra of these mixtures to understand how the structural features change with concentration and temperature. Any mixing of these two species together will depress the freezing point of the lake below Titan's surface temperature, preventing them from freezing. We will present new results utilizing our recently acquired Raman spectrometer that allow us to explore both the liquid and solid phases of the ternary system of methane, ethane and nitrogen. In particular we will explore the effect of nitrogen on the eutectic of the methane-ethane system. At high pressure we find that the ternary creates two separate liquid phases. Through spectroscopy we determined the bottom layer to be nitrogen rich, and the top layer to be ethane rich. Identifying the eutectic, as well as understanding the liquidus and solidus points of combinations of these species, has implications for not only the lakes on the surface of Titan, but also for the evaporation/condensation/cloud cycle in the atmosphere, as well as the stability of these species on other outer solar system bodies. These results will help interpretation of future observational data, and guide current theoretical models.

Oxygen demand of aircraft and airfield pavement deicers and alternative freezing point depressants

USGS Publications Warehouse

Corsi, Steven R.; Mericas, Dean; Bowman, George

2012-01-01

Aircraft and pavement deicing formulations and other potential freezing point depressants were tested for biochemical oxygen demand (BOD) and chemical oxygen demand (COD). Propylene glycol-based aircraft deicers exhibited greater BOD5 than ethylene glycol-based aircraft deicers, and ethylene glycol-based products had lower degradation rates than propylene glycol-based products. Sodium formate pavement deicers had lower COD than acetate-based pavement deicers. The BOD and COD results for acetate-based pavement deicers (PDMs) were consistently lower than those for aircraft deicers, but degradation rates were greater in the acetate-based PDM than in aircraft deicers. In a 40-day testing of aircraft and pavement deicers, BOD results at 20°C (standard) were consistently greater than the results from 5°C (low) tests. The degree of difference between standard and low temperature BOD results varied among tested products. Freshwater BOD test results were not substantially different from marine water tests at 20°C, but glycols degraded slower in marine water than in fresh water for low temperature tests. Acetate-based products had greater percentage degradation than glycols at both temperatures. An additive component of the sodium formate pavement deicer exhibited toxicity to the microorganisms, so BOD testing did not work properly for this formulation. BOD testing of alternative freezing point depressants worked well for some, there was little response for some, and for others there was a lag in response while microorganisms acclimated to the freezing point depressant as a food source. Where the traditional BOD5 test performed adequately, values ranged from 251 to 1,580 g/kg. Where the modified test performed adequately, values of BOD28 ranged from 242 to 1,540 g/kg.

A microfluidic thermometer: Precise temperature measurements in microliter- and nanoliter-scale volumes

PubMed Central

McKenzie, Brittney A.

2017-01-01

Measuring the temperature of a sample is a fundamental need in many biological and chemical processes. When the volume of the sample is on the microliter or nanoliter scale (e.g., cells, microorganisms, precious samples, or samples in microfluidic devices), accurate measurement of the sample temperature becomes challenging. In this work, we demonstrate a technique for accurately determining the temperature of microliter volumes using a simple 3D-printed microfluidic chip. We accomplish this by first filling “microfluidic thermometer” channels on the chip with substances with precisely known freezing/melting points. We then use a thermoelectric cooler to create a stable and linear temperature gradient along these channels within a measurement region on the chip. A custom software tool (available as online Supporting Information) is then used to find the locations of solid-liquid interfaces in the thermometer channels; these locations have known temperatures equal to the freezing/melting points of the substances in the channels. The software then uses the locations of these interfaces to calculate the temperature at any desired point within the measurement region. Using this approach, the temperature of any microliter-scale on-chip sample can be measured with an uncertainty of about a quarter of a degree Celsius. As a proof-of-concept, we use this technique to measure the unknown freezing point of a 50 microliter volume of solution and demonstrate its feasibility on a 400 nanoliter sample. Additionally, this technique can be used to measure the temperature of any on-chip sample, not just near-zero-Celsius freezing points. We demonstrate this by using an oil that solidifies near room temperature (coconut oil) in a microfluidic thermometer to measure on-chip temperatures well above zero Celsius. By providing a low-cost and simple way to accurately measure temperatures in small volumes, this technique should find applications in both research and educational laboratories. PMID:29284028

Large scale synthesis of nanostructured zirconia-based compounds from freeze-dried precursors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gomez, A.; Villanueva, R.; Vie, D.

2013-01-15

Nanocrystalline zirconia powders have been obtained at the multigram scale by thermal decomposition of precursors resulting from the freeze-drying of aqueous acetic solutions. This technique has equally made possible to synthesize a variety of nanostructured yttria or scandia doped zirconia compositions. SEM images, as well as the analysis of the XRD patterns, show the nanoparticulated character of those solids obtained at low temperature, with typical particle size in the 10-15 nm range when prepared at 673 K. The presence of the monoclinic, the tetragonal or both phases depends on the temperature of the thermal treatment, the doping concentration and themore » nature of the dopant. In addition, Rietveld refinement of the XRD profiles of selected samples allows detecting the coexistence of the tetragonal and the cubic phases for high doping concentration and high thermal treatment temperatures. Raman experiments suggest the presence of both phases also at relatively low treatment temperatures. - Graphical abstract: Zr{sub 1-x}A{sub x}O{sub 2-x/2} (A=Y, Sc; 0{<=}x{<=}0.12) solid solutions have been prepared as nanostructured powders by thermal decomposition of precursors obtained by freeze-drying, and this synthetic procedure has been scaled up to the 100 g scale. Highlights: Black-Right-Pointing-Pointer Zr{sub 1-x}A{sub x}O{sub 2-x/2} (A=Y, Sc; 0{<=}x{<=}0.12) solid solutions have been prepared as nanostructured powders. Black-Right-Pointing-Pointer The synthetic method involves the thermal decomposition of precursors obtained by freeze-drying. Black-Right-Pointing-Pointer The temperature of the thermal treatment controls particle sizes. Black-Right-Pointing-Pointer The preparation procedure has been scaled up to the 100 g scale. Black-Right-Pointing-Pointer This method is appropriate for the large-scale industrial preparation of multimetallic systems.« less

Linking ice accretion and crown structure: towards a model of the effect of freezing rain on tree canopies.

PubMed

Nock, Charles A; Lecigne, Bastien; Taugourdeau, Olivier; Greene, David F; Dauzat, Jean; Delagrange, Sylvain; Messier, Christian

2016-06-01

Despite a longstanding interest in variation in tree species vulnerability to ice storm damage, quantitative analyses of the influence of crown structure on within-crown variation in ice accretion are rare. In particular, the effect of prior interception by higher branches on lower branch accumulation remains unstudied. The aim of this study was to test the hypothesis that intra-crown ice accretion can be predicted by a measure of the degree of sheltering by neighbouring branches. Freezing rain was artificially applied to Acer platanoides L., and in situ branch-ice thickness was measured directly and from LiDAR point clouds. Two models of freezing rain interception were developed: 'IceCube', which uses point clouds to relate ice accretion to a voxel-based index (sheltering factor; SF) of the sheltering effect of branch elements above a measurement point; and 'IceTree', a simulation model for in silico evaluation of the interception pattern of freezing rain in virtual tree crowns. Intra-crown radial ice accretion varied strongly, declining from the tips to the bases of branches and from the top to the base of the crown. SF for branches varied strongly within the crown, and differences among branches were consistent for a range of model parameters. Intra-crown variation in ice accretion on branches was related to SF (R(2) = 0·46), with in silico results from IceTree supporting empirical relationships from IceCube. Empirical results and simulations confirmed a key role for crown architecture in determining intra-crown patterns of ice accretion. As suspected, the concentration of freezing rain droplets is attenuated by passage through the upper crown, and thus higher branches accumulate more ice than lower branches. This is the first step in developing a model that can provide a quantitative basis for investigating intra-crown and inter-specific variation in freezing rain damage. © The Author 2016. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Hatchling turtles survive freezing during winter hibernation.

PubMed Central

Storey, K B; Storey, J M; Brooks, S P; Churchill, T A; Brooks, R J

1988-01-01

Hatchlings of the painted turtle (Chrysemys picta marginata) are unique as the only reptile and highest vertebrate life form known to tolerate the natural freezing of extracellular body fluids during winter hibernation. Turtles survived frequent exposures to temperatures as low as -6 degrees C to -8 degrees C in their shallow terrestrial nests over the 1987-1988 winter. Hatchlings collected in April 1988 had a mean supercooling point of -3.28 +/- 0.24 degrees C and survived 24 hr of freezing at -4 degrees C with 53.4% +/- 1.98% of total body water as ice. Recovery appeared complete after 20 hr of thawing at 3 degrees C. However, freezing at -10.9 degrees C, resulting in 67% ice, was lethal. A survey of possible cryoprotectants revealed a 2- to 3-fold increase in glucose content of liver and blood and a 3-fold increase in blood glycerol in response to freezing. Although quantitatively low, these responses by spring turtles strongly indicate that these may be the winter-active cryoprotectants. The total amino acid pool of blood also increased 2.25-fold in freezing-exposed turtles, and taurine accounted for 52% of the increase. Most organs accumulated high concentrations of lactate during freezing, a response to the ischemic state imposed by extracellular freezing. Changes in glycogen phosphorylase activity and levels of glucose 6-phosphate and fructose 2,6-bisphosphate were also consistent with a dependence on anaerobic glycolysis during freezing. Studies of the molecular mechanisms of natural freeze tolerance in these turtles may identify protective strategies that can be used in mammalian organ cryopreservation technology. PMID:3186730

The colligative properties of fruit juices by photopyroelectric calorimetry

NASA Astrophysics Data System (ADS)

Frandas, A.; Surducan, V.; Nagy, G.; Bicanic, D.

1999-03-01

The photopyroelectric method was used to study the depression of freezing point in juices prepared from selected apple and orange juice concentrates. By using the models for real solutions, the effective molecular weight of the dissolved solids was obtained. The acids concentration in the fruit juice is reflected both in the equivalent molecular weight (by lowering it) and in the interaction coefficients b and C. Using the data for the molecular weight and the characteristic coefficients, prediction curves for the samples investigated can be used in practice. Freezing point depression can also be used as an indicator of the degree of spoilage of fruit juices.

Calculating osmotic pressure of glucose solutions according to ASOG model and measuring it with air humidity osmometry.

PubMed

Wei, Guocui; Zhan, Tingting; Zhan, Xiancheng; Yu, Lan; Wang, Xiaolan; Tan, Xiaoying; Li, Chengrong

2016-09-01

The osmotic pressure of glucose solution at a wide concentration range was calculated using ASOG model and experimentally determined by our newly reported air humidity osmometry. The measurements from air humidity osmometry were compared with the well-established freezing point osmometry and ASOG model calculations at low concentrations and with only ASOG model calculations at high concentrations where no standard experimental method could serve as a reference for comparison. Results indicate that air humidity osmometry measurements are comparable to ASOG model calculations at a wide concentration range, while at low concentrations freezing point osmometry measurements provide better comparability with ASOG model calculations.

When a water drop freezes before it solidifies

NASA Astrophysics Data System (ADS)

Kavehpour, Pirouz; Davis, Stephen; Tavakoli, Faryar

2012-11-01

When a drop of liquid is placed on a substrate which temperature is below the melting point of the liquid, one would expect the drop to solidify instantaneously. However, many liquids, such as water, must be subcooled to solidify below its melting temperature due to homogeneous nucleation's high activation energy. Most of the drop solidification research, particularly for water, phase change is assumed to occur at equilibrium freezing temperature; however, this is not the case. We found that after a certain degree of supercooling, a kinetic based nucleation begins and latent heat of fusion is suddenly liberated, causing an increase in liquid temperature. At the end of this stage, approximately 20% of the drop is crystallized. This phenomenon is known among metallurgists as recalescence. This is followed by a slow solidification process at the melting point. As a water droplet spreads on a cold substrate, its contact line stops just prior to freezing inception from the liquid-solid interface. In this study, we assert that recalescence prior to solidification may be the cause of water's sudden immobility, which results in a fixed contact angle and droplet diameter. In our experiments, the nucleation front initiates from the trijunction point and propagates to the drop volume.

SLAPex Freeze/Thaw 2015: The First Dedicated Soil Freeze/Thaw Airborne Campaign

NASA Technical Reports Server (NTRS)

Kim, Edward; Wu, Albert; DeMarco, Eugenia; Powers, Jarrett; Berg, Aaron; Rowlandson, Tracy; Freeman, Jacqueline; Gottfried, Kurt; Toose, Peter; Roy, Alexandre;

Investigation of TiC C Eutectic and WC C Peritectic High-Temperature Fixed Points

NASA Astrophysics Data System (ADS)

Sasajima, Naohiko; Yamada, Yoshiro

2008-06-01

TiC C eutectic (2,761°C) and WC C peritectic (2,749°C) fixed points were investigated to compare their potential as high-temperature thermometric reference points. Two TiC C and three WC C fixed-point cells were constructed, and the melting and freezing plateaux were evaluated by means of radiation thermometry. The repeatability of the TiC C eutectic within a day was 60 mK with a melting range roughly 200 mK. The repeatability of the melting temperature of the WC C peritectic within 1 day was 17 mK with a melting range of ˜70 mK. The repeatability of the freezing temperature of the WC C peritectic was 21 mK with a freezing range less than 20 mK. One of the TiC C cells was constructed from a TiC and graphite powder mixture. The filling showed the reaction with the graphite crucible was suppressed and the ingot contained less voids, although the lack of high-purity TiC powder poses a problem. The WC C cells were easily constructed, like metal carbon eutectic cells, without any evident reaction with the crucible. From these results, it is concluded that the WC C peritectic has more potential than the TiC C eutectic as a high-temperature reference point. The investigation of the purification of the TiC C cell during filling and the plateau observation are also reported.

30 CFR 250.428 - What must I do in certain cementing and casing situations?

Code of Federal Regulations, 2010 CFR

2010-07-01

... point. (h) Need to use less than required cement for the surface casing during floating drilling... permafrost zone uncemented Fill the annulus with a liquid that has a freezing point below the minimum...

Why are hyperactive ice-binding-proteins so active?

NASA Astrophysics Data System (ADS)

Braslavsky, Ido; Celik, Yeliz; Pertaya, Natalya; Eun Choi, Young; Bar, Maya; Davies, Peter L.

2008-03-01

Ice binding proteins (IBPs), also called `antifreeze proteins' or `ice structuring proteins', are a class of proteins that protect organisms from freezing injury. These proteins have many applications in medicine and agriculture, and as a platform for future biotechnology applications. One of the interesting questions in this field focuses on the hyperactivity of some IBPs. Ice binding proteins can be classified in two groups: moderate ones that can depress the freezing point up to ˜1.0 ^oC and hyperactive ones that can depress the freezing point several-fold further even at lower concentrations. It has been suggested that the hyperactivity of IBPs stem from the fact that they block growth out of specific ice surfaces, more specifically the basal planes of ice. Here we show experimental results based on fluorescence microscopy, highlighting the differences between moderate IBPs and hyperactive IBPs. These include direct evidence for basal plane affinity of hyperactive IBPs, the effects of IBPs on growth-melt behavior of ice and the dynamics of their interaction with ice.

Scanning electron microscopy of high-pressure-frozen sea urchin embryos.

PubMed

Walther, P; Chen, Y; Malecki, M; Zoran, S L; Schatten, G P; Pawley, J B

1993-12-01

High-pressure-freezing permits direct cryo-fixation of sea urchin embryos having a defined developmental state without the formation of large ice crystals. We have investigated preparation protocols for observing high-pressure-frozen and freeze-fractured samples in the scanning electron microscope. High-pressure-freezing was superior to other freezing protocols, because the whole bulk sample was reasonably well frozen and the overall three-dimensional shape of the embryos was well preserved. The samples were either dehydrated by freeze-substitution and critical-point-drying, or imaged in the partially hydrated state, using a cold stage in the SEM. During freeze-substitution the samples were stabilized by fixatives. The disadvantage of this method was that shrinking and extraction effects, caused by the removal of the water, could not be avoided. These disadvantages were avoided when the sample was imaged in the frozen-hydrated state using a cold-stage in the SEM. This would be the method of choice for morphometric studies. Frozen-hydrated samples, however, were very beam sensitive and many structures remained covered by the ice and were not visible. Frozen-hydrated samples were partially freeze-dried to make visible additional structures that had been covered by ice. However, this method also caused drying artifacts when too much water was removed.

Kinetics of Water Loss from Cells at Subzero Temperatures and the Likelihood of Intracellular Freezing

PubMed Central

Mazur, Peter

1963-01-01

The survival of various cells subjected to low temperature exposure is higher when they are cooled slowly. This increase is consistent with the view that slow cooling decreases the probability of intracellular freezing by permitting water to leave the cell rapidly enough to keep the protoplasm at its freezing point. The present study derives a quantitative relation between the amount of water in a cell and temperature. The relation is a differential equation involving cooling rate, surface-volume ratio, membrane permeability to water, and the temperature coefficient of the permeability constant. Numerical solutions to this equation give calculated water contents which permit predictions as to the likelihood of intracellular ice formation. Both the calculated water contents and the predictions on internal freezing are consistent with the experimental observations of several investigators. PMID:14085017

Novel method of realizing metal freezing points by induced solidification

NASA Astrophysics Data System (ADS)

Ma, C. K.

1997-07-01

The freezing point of a pure metal, tf, is the temperature at which the solid and liquid phases are in equilibrium. The purest metal available is actually a dilute alloy. Normally, the liquidus point of a sample, tl, at which the amount of the solid phase in equilibrium with the liquid phase is minute, provides the closest approximation to tf. Thus the experimental realization of tf is a matter of realizing tl. The common method is to cool a molten sample continuously so that it supercools and recalesces. The highest temperature after recalescence is normally the best experimental value of tl. In the realization, supercooling of the sample at the sample container and the thermometer well is desirable for the formation of dual solid-liquid interfaces to thermally isolate the sample and the thermometer. However, the subsequent recalescence of the supercooled sample requires the formation of a certain amount of solid, which is not minute. Obviously, the plateau temperature is not the liquidus point. In this article we describe a method that minimizes supercooling. The condition that provides tl is closely approached so that the latter may be measured. As the temperature of the molten sample approaches the anticipated value of tl, a small solid of the same alloy is introduced into the sample to induce solidification. In general, solidification does not occur as long as the temperature is above or at tl, and occurs as soon as the sample supercools minutely. Thus tl can be obtained, in principle, by observing the temperature at which induced solidification begins. In case the solid is introduced after the sample has supercooled slightly, a slight recalescence results and the subsequent maximum temperature is a close approximation to tl. We demonstrate that the principle of induced solidification is indeed applicable to freezing point measurements by applying it to the design of a copper-freezing-point cell for industrial applications, in which a supercooled sample is reheated and then induced to solidify by the solidification of an auxiliary sample. Further experimental studies are necessary to assess the practical advantages and disadvantages of the induction method.

Small copper fixed-point cells of the hybrid type to be used in place of normal larger cells

NASA Astrophysics Data System (ADS)

Battuello, M.; Girard, F.; Florio, M.

2012-10-01

Two small cells for the realization of the fixed point of copper were constructed and investigated at INRIM. They are of the same hybrid design generally adopted for the eutectic high-temperature fixed-point cells, namely a structure with a sacrificial graphite sleeve and a layer of flexible carbon-carbon composite sheet (C/C sheet). Because of the largely different design with respect to the cells normally adopted for the construction of pure metal fixed points, they were compared and characterized with respect to the normal cells used at INRIM for the ITS-90 realization. Two different furnaces were used to compare hybrid and normal cells. One of the hybrid cells was also used in different configurations, i.e. without the C/C sheet and with two layers of sheet. The cells were compared with different operative conditions, i.e. temperature settings of the furnaces for inducing the freeze, and repeatability and reproducibility were investigated. Freezing temperature and shape of the plateaux obtained under the different conditions were analysed. As expected the duration of the plateaux obtained with the hybrid cells is considerably shorter than with the normal cell, but this does not affect the results in terms of freezing temperature. Measurements with the modified cell showed that the use of a double C/C sheet may improve both repeatability and reproducibility of the plateaux.

Cold Heat Storage Characteristics of O/W-type Latent Heat Emulsion Including Continuum Phase of Water Treated with a Freezing Point Depression

NASA Astrophysics Data System (ADS)

Inaba, Hideo; Morita, Shin-Ichi

This paper deals with flow and cold heat storage characteristics of the oil (tetradecane, C14H30, freezing point 278.9 K, Latent heat 229 kJ/kg)/water emulsion as a latent heat storage material having a low melting point. The test emulsion includes a water-urea solution as a continuum phase. The freezing point depression of the continuum phase permits enhancement of the heat transfer rate of the emulison, due to the large temperature difference between the latent heat storage material and water-urea solution. The velocity of emulsion flow and the inlet temperature of coolant in a coiled double tube heat exchanger are chosen as the experimental parameters. The pressure drop, the heat transfer coefficient of the emulsion in the coiled tube are measured in the temperture region over solid and liquid phase of the latent heat storage material. The finishing time of the cold heat storage is defined experimentally in the range of sensible and latent heat storage. It is clarified that the flow behavior of the emulsion as a non-Newtonian fluid has an important role in cold heat storage. The useful nondimentional correlation equations for the additional pressure loss coefficient, the heat transfer coefficient and the finishing time of the cold heat storage are derived in terms of Dean number and heat capacity ratio.

Effect of the Various Steps in the Processing of Human Milk in the Concentrations of IgA, IgM, and Lactoferrin.

PubMed

Arroyo, Gerardo; Ortiz Barrientos, Kevin Alexander; Lange, Karla; Nave, Federico; Miss Mas, Gabriela; Lam Aguilar, Pamela; Soto Galindo, Miguel Angel

2017-09-01

Human milk immune components are unique and important for the development of the newborn. Milk processing at the Human Milk Banks (HMB), however, causes partial destruction of immune proteins. The objective of this study was to determine the effects that heating during the milk processing procedure at the HMB had on the concentrations of IgA, IgM, and lactoferrin at three critical points in time. Fifty milk samples (150 mL) were collected from voluntary donors at the HMB at the Hospital Nacional Pedro de Bethancourt, located in Antigua Guatemala. Samples from three critical points in time during the milk processing procedure were selected for analysis: freezing/thawing I, freezing/thawing II, and pasteurization. IgA, IgM, and lactoferrin concentrations were determined during each critical point and compared with a baseline concentration. After milk processing, IgA, IgM, and lactoferrin mean concentrations were reduced by 30.0%, 36.0%, and 70.0%, respectively (p < 0.001). Reduction of biological activity was mainly attributed to pasteurization for IgA and lactoferrin (p < 0.001); the first freezing/thawing processes before pasteurization showed no significant reduction difference between mean concentrations of IgA (p = 0.160) and lactoferrin (p = 0.345) but showed a significant effect on IgM concentration (p = 0.016), and the second freezing/thawing procedure only showed a significant effect on IgA (p < 0.001). The effects of milk processing on the immune proteins that were evaluated in this study demonstrated a significant reduction.

30 CFR 35.6 - Application procedures and requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Pour point, °F.; freezing point, °F.; color; neutralization number or pH; viscosity at 100 °F., 150 °F., 175 °F. (Saybolt or Furol); viscosity index; specific gravity. (3) A statement of the water or other...

30 CFR 35.6 - Application procedures and requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Pour point, °F.; freezing point, °F.; color; neutralization number or pH; viscosity at 100 °F., 150 °F., 175 °F. (Saybolt or Furol); viscosity index; specific gravity. (3) A statement of the water or other...

30 CFR 35.6 - Application procedures and requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Pour point, °F.; freezing point, °F.; color; neutralization number or pH; viscosity at 100 °F., 150 °F., 175 °F. (Saybolt or Furol); viscosity index; specific gravity. (3) A statement of the water or other...

Colloid-facilitated mobilization of metals by freeze-thaw cycles.

PubMed

Mohanty, Sanjay K; Saiers, James E; Ryan, Joseph N

2014-01-21

The potential of freeze-thaw cycles to release colloids and colloid-associated contaminants into water is unknown. We examined the effect of freeze-thaw cycles on the mobilization of cesium and strontium in association with colloids in intact cores of a fractured soil, where preferential flow paths are prevalent. Two intact cores were contaminated with cesium and strontium. To mobilize colloids and metal cations sequestered in the soil cores, each core was subjected to 10 intermittent wetting events separated by 66 h pauses. During the first five pauses, the cores were dried at room temperature, and during last five pauses, the cores were subjected to 42 h of freezing followed by 24 h of thawing. In comparison to drying, freeze-thaw cycles created additional preferential flow paths through which colloids, cesium, and strontium were mobilized. The wetting events following freeze-thaw intervals mobilized about twice as many colloids as wetting events following drying at room temperature. Successive wetting events following 66 h of drying mobilized similar amounts of colloids; in contrast, successive wetting events after 66 h of freeze-thaw intervals mobilized greater amounts of colloids than the previous one. Drying and freeze-thaw treatments, respectively, increased and decreased the dissolved cesium and strontium, but both treatments increased the colloidal cesium and strontium. Overall, the freeze-thaw cycles increased the mobilization of metal contaminants primarily in association with colloids through preferential flow paths. These findings suggest that the mobilization of colloid and colloid-associated contaminants could increase when temperature variations occur around the freezing point of water. Thus, climate extremes have the potential to mobilize contaminants that have been sequestered in the vadose zone for decades.

Development of modulated optical transmission system to determinate the cloud and freezing points in biofuels.

PubMed

Jaramillo-Ochoa, Liliana; Ramirez-Gutierrez, Cristian F; Sánchez-Moguel, Alonso; Acosta-Osorio, Andrés; Rodriguez-Garcia, Mario E

2015-01-01

This work is focused in the development of a modulated optical transmission system with temperature control to determine the thermal properties of biodiesels such as the cloud and freezing points. This system is able to determine these properties in real time without relying on the operator skills as indicated in the American Society for Testing Materials (ASTM) norms. Thanks to the modulation of the incident laser, the noise of the signal is reduced and two information channels are generated: amplitude and phase. Lasers with different wavelengths can be used in this system but the sample under study must have optical absorption at the wavelength of the laser.

Temperature calibration of cryoscopic solutions used in the milk industry by adiabatic calorimetry

NASA Astrophysics Data System (ADS)

Méndez-Lango, E.; Lira-Cortes, L.; Quiñones-Ibarra, R.

2013-09-01

One method to detect extraneous water in milk is through cryoscopy. This method is used to measure the freezing point of milk. For calibration of a cryoscope there are is a set of standardized solution with known freezing points values. These values are related with the solute concentration, based in almost a century old data; it was no found recent results. It was found that reference solution are not certified in temperature: they do not have traceability to the temperature unit or standards. We prepared four solutions and measured them on a cryoscope and on an adiabatic calorimeter. It was found that results obtained with one technique dose not coincide with the other one.

Influence of Rapid Freeze-Thaw Cycling on the Mechanical Properties of Sustainable Strain-Hardening Cement Composite (2SHCC)

PubMed Central

Jang, Seok-Joon; Rokugo, Keitetsu; Park, Wan-Shin; Yun, Hyun-Do

2014-01-01

This paper provides experimental results to investigate the mechanical properties of sustainable strain-hardening cement composite (2SHCC) for infrastructures after freeze-thaw actions. To improve the sustainability of SHCC materials in this study, high energy-consumptive components—silica sand, cement, and polyvinyl alcohol (PVA) fibers—in the conventional SHCC materials are partially replaced with recycled materials such as recycled sand, fly ash, and polyethylene terephthalate (PET) fibers, respectively. To investigate the mechanical properties of green SHCC that contains recycled materials, the cement, PVA fiber and silica sand were replaced with 10% fly ash, 25% PET fiber, and 10% recycled aggregate based on preliminary experimental results for the development of 2SHCC material, respectively. The dynamic modulus of elasticity and weight for 2SHCC material were measured at every 30 cycles of freeze-thaw. The effects of freeze-thaw cycles on the mechanical properties of sustainable SHCC are evaluated by conducting compressive tests, four-point flexural tests, direct tensile tests and prism splitting tests after 90, 180, and 300 cycles of rapid freeze-thaw. Freeze-thaw testing was conducted according to ASTM C 666 Procedure A. Test results show that after 300 cycles of freezing and thawing actions, the dynamic modulus of elasticity and mass loss of damaged 2SHCC were similar to those of virgin 2SHCC, while the freeze-thaw cycles influence mechanical properties of the 2SHCC material except for compressive behavior. PMID:28788522

Melting/freezing behavior of a fluid confined in porous glasses and MCM-41: Dielectric spectroscopy and molecular simulation

NASA Astrophysics Data System (ADS)

Sliwinska-Bartkowiak, Malgorzata; Dudziak, Grazyna; Sikorski, Roman; Gras, Roman; Radhakrishnan, Ravi; Gubbins, Keith E.

2001-01-01

We report both experimental measurements and molecular simulations of the melting and freezing behavior of fluids in nanoporous media. The experimental studies are for nitrobenzene in the silica-based pores of controlled pore glass, Vycor, and MCM-41. Dielectric relaxation spectroscopy is used to determine melting points and the orientational relaxation times of the nitrobenzene molecules in the bulk and the confined phase. Monte Carlo simulations, together with a bond orientational order parameter method, are used to determine the melting point and fluid structure inside cylindrical pores modeled on silica. Qualitative comparison between experiment and simulation are made for the shift in the freezing temperatures and the structure of confined phases. From both the experiments and the simulations, it is found that the confined fluid freezes into a single crystalline structure for average pore diameters greater than 20σ, where σ is the diameter of the fluid molecule. For average pore sizes between 20σ and 15σ, part of the confined fluid freezes into a frustrated crystal structure with the rest forming an amorphous region. For pore sizes smaller than 15σ, even the partial crystallization did not occur. Our measurements and calculations show clear evidence of a novel intermediate "contact layer" phase lying between liquid and crystal; the contact layer is the confined molecular layer adjacent to the pore wall and experiences a deeper fluid-wall potential energy compared to the inner layers. We also find evidence of a liquid to "hexatic" transition in the quasi-two-dimensional contact layer at high temperatures.

Antifreeze glycoproteins from antarctic notothenioid fishes fail to protect the rat cardiac explant during hypothermic and freezing preservation.

PubMed

Wang, T; Zhu, Q; Yang, X; Layne, J R; Devries, A L

1994-04-01

The antarctic notothenioid fishes avoid freezing through the action of circulating antifreeze glycoproteins (AFGPs). This study investigated whether AFGPs could serve as cryoprotectants for the isolated rat heart under three different storage conditions. (1) Hearts were flushed with 15 mg AFGP/ml cardioplegic solution (CP) and stored for 9 h at 0 degrees C. This AFGP concentration has been reported to protect pig oocytes during hypothermic storage. (2) Hearts were flushed with 10 mg AFGP/ml CP-14 and stored frozen at -1.4 degrees C for 3 h. At this concentration the AFGPs significantly reduce the solution freezing point and also change the crystal morphology from dendritic to spicular. (3) Hearts were flushed with 10 micrograms AFGP/ml CP-15 and stored frozen at -1.4 degrees C for 5 h. At this low concentration the AFGPs have a strong inhibitory effect on ice recrystallization, but have little effect on the freezing point and less apparent effect on the crystal habit. After hypothermic or freezing storage, the functional viability was assessed by determining cardiac output (CO) during working reperfusion. No difference in CO was found between AFGP-treated and untreated hearts after 9 h of 0 degree C storage. CO in hearts frozen in CP-14 without AFGPs recovered to 50% of the freshly perfused control hearts. Hearts frozen in the presence of high concentrations of AFGPs (10 mg/ml CP-14) failed to beat upon thawing and reperfusion, although their tissue ice content was less than that found in hearts without AFGP treatment.(ABSTRACT TRUNCATED AT 250 WORDS)

Freeze-fracture of infected plant leaves in ethanol for scanning electron microscopic study of fungal pathogens.

PubMed

Moore, Jayma A; Payne, Scott A

2012-01-01

Fungi often are found within plant tissues where they cannot be visualized with the scanning electron microscope (SEM). We present a simple way to reveal cell interiors while avoiding many common causes of artifact. Freeze-fracture of leaf tissue using liquid nitrogen during the 100% ethanol step of the dehydration process just before critical point drying is useful in exposing intracellular fungi to the SEM.

The effect of low temperature on Antarctic endolithic green algae

NASA Technical Reports Server (NTRS)

Meyer, M. A.; Morris, G. J.; Friedmann, E. I.

1988-01-01

Laboratory experiments show that undercooling to about -5 degrees C occurs in colonized Beacon sandstones of the Ross Desert, Antarctica. High-frequency temperature oscillations between 5 degrees C and -5 degrees C or -10 degrees C (which occur in nature on the rock surface) did not damage Hemichloris antarctica. In a cryomicroscope, H. antarctica appeared to be undamaged after slow or rapid cooling to -50 degrees C. 14CO2 incorporation after freezing to -20 degrees C was unaffected in H. antarctica or in Trebouxia sp. but slightly depressed in Stichococcus sp. (isolated from a less extreme Antarctic habitat). These results suggest that the freezing regime in the Antarctic desert is not injurious to endolithic algae. It is likely that the freezing-point depression inside the rock makes available liquid water for metabolic activity at subzero temperatures. Freezing may occur more frequently on the rock surface and contribute to the abiotic nature of the surface.

A Pulsed Plasma Thruster Using Dimethyl Ether as Propellant

NASA Astrophysics Data System (ADS)

Masui, Souichi; Okada, Terumasa; Kitatomi, Makoto; Kakami, Akira; Tachibana, Takeshi

The pulsed plasma thruster (PPT), has attracted attention again as a micro-thruster because of its compactness, light weight, and comparatively low power consumption. On the other hand, the propellant utilization efficiency of a conventinal Teflon PPT is relatively low among electric propulsion devices because a propellant that originates from late-time ablation produces negligible thrust. The liquid propellant PPT (LP-PPT), in which water or ethanol is fed with an injector, was proposed to overcome these difficulties. Thrust measurements show that a LP-PPT provides higher specific impulses than a conventional PPT. However, water requires temperature management for propellant storage due to its relatively high freezing point. Moreover, even if ethanol, which has a sufficiently low freezing point, is used as propellant, a pressurant is necessary, as well as water, because the vapor pressures are insufficient for self-pressurization. In this study, we propose to use dimethyl ether (DME) as the propellant. DME, which has a freezing point of 131 K at 1 atm and a vapor pressure of 6 atm at 298 K, can be stored in tanks as a liquid, and requires no feeding pressurant. We designed a DME pulsed plasma thruster to evaluate performance. Thrust measurement yielded a specific impulse of 430 s for a coaxial type at a capacitor-stored energy of 13 J.

Observation of surface layering in a nonmetallic liquid

NASA Astrophysics Data System (ADS)

Mo, Haiding; Evmenenko, Guennadi; Kewalramani, Sumit; Kim, Kyungil; Dutta, Pulak; Ehrlich, Steven

2006-03-01

Non-monotonic density profiles (layers) have previously been observed at the free surfaces of many metallic liquids, but not in isotropic dielectric liquids. Whether the presence of an electron gas is necessary for surface layering has been the subject of debate. Until recently, MD simulations have suggested that layering at free liquid interface may be a generic phenomenon and is not limited to the metallic liquids^1. The theories predict that if normal liquids can be cooled down to temperatures low enough, layering structure should be observed experimentally. However, this is difficult for most molecular liquids because these liquids freeze well above the temperature necessary for observing the layering structure. By studying the surface structure of liquid TEHOS (tetrakis(2-ethylhexoxy)silane), which combines relatively low freezing point and high boiling point compared to that of most molecular liquids, we have observed the evidence of layering at the free interface of liquid TEHOS using x-ray reflectivity. When cooled to T/Tc 0.25 (well above the bulk freezing point, Tc is the critical temperature of TEHOS), the surface roughness drops sharply and density oscillations appear near the surface. Lateral ordering of the surface layers is liquid-like, just as at liquid metal surfaces. 1. E. Chac'on and P. Tarazona, Phys. Rev. Lett. 91 166103-1 (2003)

Theory of freezing in simple systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cerjan, C.; Bagchi, B.

The transition parameters for the freezing of two one-component liquids into crystalline solids are evaluated by two theoretical approaches. The first system considered is liquid sodium which crystallizes into a body-centered-cubic (bcc) lattice; the second system is the freezing of adhesive hard spheres into a face-centered-cubic (fcc) lattice. Two related theoretical techniques are used in this evaluation: One is based upon a recently developed bifurcation analysis; the other is based upon the theory of freezing developed by Ramakrishnan and Yussouff. For liquid sodium, where experimental information is available, the predictions of the two theories agree well with experiment and eachmore » other. The adhesive-hard-sphere system, which displays a triple point and can be used to fit some liquids accurately, shows a temperature dependence of the freezing parameters which is similar to Lennard-Jones systems. At very low temperature, the fractional density change on freezing shows a dramatic increase as a function of temperature indicating the importance of all the contributions due to the triplet direction correlation function. Also, we consider the freezing of a one-component liquid into a simple-cubic (sc) lattice by bifurcation analysis and show that this transition is highly unfavorable, independent of interatomic potential choice. The bifurcation diagrams for the three lattices considered are compared and found to be strikingly different. Finally, a new stability analysis of the bifurcation diagrams is presented.« less

Freeze-dried, mucoadhesive system for vaginal delivery of the HIV microbicide, dapivirine: optimisation by an artificial neural network.

PubMed

Woolfson, A David; Umrethia, Manish L; Kett, Victoria L; Malcolm, R Karl

2010-03-30

Dapivirine mucoadhesive gels and freeze-dried tablets were prepared using a 3x3x2 factorial design. An artificial neural network (ANN) with multi-layer perception was used to investigate the effect of hydroxypropyl-methylcellulose (HPMC): polyvinylpyrrolidone (PVP) ratio (X1), mucoadhesive concentration (X2) and delivery system (gel or freeze-dried mucoadhesive tablet, X3) on response variables; cumulative release of dapivirine at 24h (Q(24)), mucoadhesive force (F(max)) and zero-rate viscosity. Optimisation was performed by minimising the error between the experimental and predicted values of responses by ANN. The method was validated using check point analysis by preparing six formulations of gels and their corresponding freeze-dried tablets randomly selected from within the design space of contour plots. Experimental and predicted values of response variables were not significantly different (p>0.05, two-sided paired t-test). For gels, Q(24) values were higher than their corresponding freeze-dried tablets. F(max) values for freeze-dried tablets were significantly different (2-4 times greater, p>0.05, two-sided paired t-test) compared to equivalent gels. Freeze-dried tablets having lower values for X1 and higher values for X2 components offered the best compromise between effective dapivirine release, mucoadhesion and viscosity such that increased vaginal residence time was likely to be achieved. Copyright (c) 2009 Elsevier B.V. All rights reserved.

Equilibrium freezing of leaf water and extracellular ice formation in Afroalpine 'giant rosette' plants.

PubMed

Beck, E; Schulze, E D; Senser, M; Scheibe, R

1984-09-01

The water potentials of frozen leaves of Afroalpine plants were measured psychrometrically in the field. Comparison of these potentials with the osmotic potentials of an expressed cellular sap and the water potentials of ice indicated almost ideal freezing behaviour and suggested equilibrium freezing. On the basis of the osmotic potentials of expressed cellular sap, the fractions of frozen cellular water which correspond to the measured water potentials of the frozen leaves could be determined (e.g. 74% at -3.0° C). The freezing points of leaves were found to be in the range between 0° C and -0.5° C, rendering evidence for freezing of almost pure water and thus confirming the conclusions drawn from the water-potential measurements. The leaves proved to be frost resistant down to temperatures between -5° C and -15° C, as depending on the species. They tolerated short supercooling periods which were necessary in order to start ice nucleation. Extracellular ice caps and ice crystals in the intercellular space were observed when cross sections of frozen leaves were investigated microscopically at subfreezing temperatures.

Physiological limitation at alpine treeline: relationships of threshold responses of conifers to their establishment patterns

NASA Astrophysics Data System (ADS)

Germino, M. J.; Lazarus, B.; Castanha, C.; Moyes, A. B.; Kueppers, L. M.

2014-12-01

An understanding of physiological limitations to tree establishment at alpine treeline form the basis for predicting how this climate-driven boundary will respond to climate shifts. Most research on this topic has focused on limitations related to carbon balance and growth of trees. Carbon balance could limit survival and establishment primarily through slow-acting, chronic means. We asked whether tree survival and thus establishment patterns reflect control by chronic effects in comparison to acute, threshold responses, such as survival of frost events. Seedling survivorship patterns were compared to thresholds in freezing (temperature causing leaf freezing, or freezing point, FP; and physiological response to freezing) and water status (turgor loss point, TLP; and related physiological adjustments). Subject seedlings were from forest, treeline, and alpine sites in the Alpine Treeline Warming Experiment in Colorado, and included limber and lodgepole pine (a low-elevation species), and Engelmann Spruce. Preliminary results show survival increases with seedling age, but the only corresponding increase in stress acclimation was photosynthetic resistance to freezing and TLP, not FP. Differences in survivorship among the species were not consistent with variation in FP but they generally agreed with variation in photosynthetic resistance to deep freezing and to early-season drought avoidance. Mortality of limber pine increased 35% when minimum temperatures decreased below -9C, which compares with FPs of >-8.6C, and about 1/3 of its mortality occurred during cold/wet events, particularly in the alpine. The other major correlate of mortality is midsummer drying events, as previously reported. Also in limber pine, the TLP for year-old seedlings (-2.5 MPa) corresponded with seasonal-drought mortality. In summary, we show several examples of correspondence in physiological thresholds to mortality events within a species, although the relationships are not strong. Across species, photosynthetic resistance to freezing and early-season drought avoidance related well to mortality patterns. These results are generally more supportive of the role of chronic rather than acute climate effects in broad patterns of tree seedling establishment at treeline.

Medication and trial duration influence postural and pointing parameters during a standing repetitive pointing task in individuals with Parkinson's disease.

PubMed

Jehu, Deborah A; Cantù, Hiram; Hill, Allen; Paquette, Caroline; Côté, Julie N; Nantel, Julie

2018-01-01

We aimed to determine the effects of levodopa medication on the performance of a repetitive pointing task while standing, and to investigate the optimal trial duration in individuals with Parkinson's disease, and older adults. Seventeen individuals with Parkinson's disease (5 freezers) and 9 older adults stood on force platforms for 30 s and 120 s while performing a bilateral repetitive pointing task, tracked by motion capture. Participants with Parkinson's disease were assessed on and off medication and older adults were also assessed on separate days. The main findings were that: 1) on medication, participants with Parkinson's exhibited greater center of pressure root mean square in the medial-lateral direction, greater velocity in the medial-lateral and anterior-posterior directions, and greater range in the medial-lateral direction than off medication; 2) longer trial durations resulted in greater center of pressure range in the medial-lateral and anterior-posterior directions and greater coefficient of variation in finger pointing on the least affected side; 3) Parkinson's participants exhibited larger range in the medial-lateral direction compared to older adults; 4) off medication, freezers presented with less range and root mean square in the anterior-posterior direction than non-freezers; and 5) a correlation emerged between the freezing of gait questionnaire and pointing asymmetry and the coefficient of variation of pointing on the most affected side. Therefore, Parkinson's medication may increase instability during a repetitive pointing task. Longer trials may provide a better depiction of sway by discriminating between those with and without neurological impairment. Individuals with Parkinson's were less stable than older adults, supporting that they are at a greater risk for falls. The greater restrictive postural strategy in freezers compared to non-freezers is likely a factor that augments fall-risk. Lastly, the link between freezing of gait and upper-limb movement indicates that freezing may manifest first in the lower-limbs.

New High-Performance Droplet Freezing Assay (HP-DFA) for the Analysis of Ice Nuclei with Complex Composition

NASA Astrophysics Data System (ADS)

Kunert, Anna Theresa; Scheel, Jan Frederik; Helleis, Frank; Klimach, Thomas; Pöschl, Ulrich; Fröhlich-Nowoisky, Janine

2016-04-01

Freezing of water above homogeneous freezing is catalyzed by ice nucleation active (INA) particles called ice nuclei (IN), which can be of various inorganic or biological origin. The freezing temperatures reach up to -1 °C for some biological samples and are dependent on the chemical composition of the IN. The standard method to analyze IN in solution is the droplet freezing assay (DFA) established by Gabor Vali in 1970. Several modifications and improvements were already made within the last decades, but they are still limited by either small droplet numbers, large droplet volumes or inadequate separation of the single droplets resulting in mutual interferences and therefore improper measurements. The probability that miscellaneous IN are concentrated together in one droplet increases with the volume of the droplet, which can be described by the Poisson distribution. At a given concentration, the partition of a droplet into several smaller droplets leads to finely dispersed IN resulting in better statistics and therefore in a better resolution of the nucleation spectrum. We designed a new customized high-performance droplet freezing assay (HP-DFA), which represents an upgrade of the previously existing DFAs in terms of temperature range and statistics. The necessity of observing freezing events at temperatures lower than homogeneous freezing due to freezing point depression, requires high-performance thermostats combined with an optimal insulation. Furthermore, we developed a cooling setup, which allows both huge and tiny temperature changes within a very short period of time. Besides that, the new DFA provides the analysis of more than 750 droplets per run with a small droplet volume of 5 μL. This enables a fast and more precise analysis of biological samples with complex IN composition as well as better statistics for every sample at the same time.

Durability assessments of concrete using electrical properties and acoustic emission testing

NASA Astrophysics Data System (ADS)

Todak, Heather N.

Premature damage deterioration has been observed in pavement joints throughout the Midwestern region of the United States. Over time, severe joint damage creates a transportation safety concern and the necessary repairs can be an extreme economic burden. The deterioration is due in part to freeze-thaw damage associated with fluid accumulation at the pavement joints. This very preventable problem is an indication that current specifications and construction practices for freeze-thaw durability of concrete are inadequate. This thesis serves to create a better understanding of moisture ingress, freeze-thaw damage mechanisms, and the effect of variations in mixture properties on freeze-thaw behavior of concrete. The concepts of the nick point degree of saturation, sorptivity rates, and critical degree of saturation are discussed. These factors contribute to service life, defined in this study as the duration of time a concrete element remains below levels of critical saturation which are required for damage development to initiate. A theoretical model and a simple experimental procedure are introduced which help determine the nick point for a series of 32 concrete mixtures with unique mixture proportions and air entrainment properties. This simple experimental procedure is also presented as a method to measure important electrical properties in order to establish the formation factor, a valuable measure of concrete transport properties. The results of freeze-thaw testing with acoustic emission monitoring are presented to help understand and quantify damage development in concrete specimens when conditioned to various degrees of saturation. This procedure was used to study the relationship between air entrainment properties and the critical degree of saturation. Applying the concepts of degree of saturation and sorptivity, a performance-based model is proposed as a new approach to specifications for freeze-thaw durability. Finally, a conceptual model is presented to illustrate the effect of various changes in mixture proportions and air void properties on service life.

Satellite freeze forecast system

NASA Technical Reports Server (NTRS)

Martsolf, J. D. (Principal Investigator)

1983-01-01

Provisions for back-up operations for the satellite freeze forecast system are discussed including software and hardware maintenance and DS/1000-1V linkage; troubleshooting; and digitized radar usage. The documentation developed; dissemination of data products via television and the IFAS computer network; data base management; predictive models; the installation of and progress towards the operational status of key stations; and digital data acquisition are also considered. The d addition of dew point temperature into the P-model is outlined.

A theoretical extension of the soil freezing curve paradigm

NASA Astrophysics Data System (ADS)

Amiri, Erfan A.; Craig, James R.; Kurylyk, Barret L.

2018-01-01

Numerical models of permafrost evolution in porous media typically rely upon a smooth continuous relation between pore ice saturation and sub-freezing temperature, rather than the abrupt phase change that occurs in pure media. Soil scientists have known for decades that this function, known as the soil freezing curve (SFC), is related to the soil water characteristic curve (SWCC) for unfrozen soils due to the analogous capillary and sorptive effects experienced during both soil freezing and drying. Herein we demonstrate that other factors beyond the SFC-SWCC relationship can influence the potential range over which pore water phase change occurs. In particular, we provide a theoretical extension for the functional form of the SFC based upon the presence of spatial heterogeneity in both soil thermal conductivity and the freezing point depression of water. We infer the functional form of the SFC from many abrupt-interface 1-D numerical simulations of heterogeneous systems with prescribed statistical distributions of water and soil properties. The proposed SFC paradigm extension has the appealing features that it (1) is determinable from measurable soil and water properties, (2) collapses into an abrupt phase transition for homogeneous media, (3) describes a wide range of heterogeneity within a single functional expression, and (4) replicates the observed hysteretic behavior of freeze-thaw cycles in soils.

[Effect of freezing and cooking on the texture and electrophoretic pattern of the proteins of octopus arms (Octopus vulgaris)].

PubMed

Reyes, Genara; Nirchio, Mauro; Bello, Rafael; Borderías, Javier

2014-09-01

Texture is the most valuable feature in cephalopods. Factors that mainly affect the texture of octopus are: freezing, scalding and cooking. The aim of this study was to assess the effect of freezing, scalding and length of cooking time on the texture and electrophoretic pattern of proteins of octopus arms. Octopuses were trapped near Margarita Island and carried with ice to the laboratory where they were packed and subjected to: a) freezing at -27 degrees C or at -20 degrees C b) scalding c) cooking for 25 min, 35 min or 45 min. Shear force was determined by Kramer cell on strips of octopus arms. SDS-PAGE was done according to the Laemmli method with 12% polyacrilamide gels. A sensory evaluation of the preference of texture was carried out using a hedonic scale of 7-points and a non-trained panel. Octopus texture was not affected by freezing temperature or scalding. Frozen octopus was softer after cooking than fresh. The longer the cooking time was, the softer the octopus was. Myosin heavy chain (MHC) was not significantly affected by scalding or cooking; however large aggregates heavier than MHC, new bands and loss of resolution of the bands appeared. Myosin and paramyosin bands were more affected by freezing prior to cooking.

Time-Referenced Effects of an Internal vs. External Focus of Attention on Muscular Activity and Compensatory Variability

PubMed Central

Hossner, Ernst-Joachim; Ehrlenspiel, Felix

2010-01-01

The paralysis-by-analysis phenomenon, i.e., attending to the execution of one's movement impairs performance, has gathered a lot of attention over recent years (see Wulf, 2007, for a review). Explanations of this phenomenon, e.g., the hypotheses of constrained action (Wulf et al., 2001) or of step-by-step execution (Masters, 1992; Beilock et al., 2002), however, do not refer to the level of underlying mechanisms on the level of sensorimotor control. For this purpose, a “nodal-point hypothesis” is presented here with the core assumption that skilled motor behavior is internally based on sensorimotor chains of nodal points, that attending to intermediate nodal points leads to a muscular re-freezing of the motor system at exactly and exclusively these points in time, and that this re-freezing is accompanied by the disruption of compensatory processes, resulting in an overall decrease of motor performance. Two experiments, on lever sequencing and basketball free throws, respectively, are reported that successfully tested these time-referenced predictions, i.e., showing that muscular activity is selectively increased and compensatory variability selectively decreased at movement-related nodal points if these points are in the focus of attention. PMID:21833285

DETAIL OF CONNECTION TO SWITCH POINTS OF TURNOUT 29, LOOKING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OF CONNECTION TO SWITCH POINTS OF TURNOUT 29, LOOKING EAST. SILVER BOX HOUSES ELECTRICAL CONTACTS FOR POSITION FEEDBACK TO SIGNAL CIRCUITS. SHEET METAL COVERS GAS-FIRED SWITCH HEATER FOR FREEZE PROTECTION IN WINTER. - Baltimore & Ohio Railroad, Z Tower, State Route 46, Keyser, Mineral County, WV

The importance of dissolved salts to the in vivo efficacy of antifreeze proteins.

PubMed

Evans, Robert P; Hobbs, Rod S; Goddard, Sally V; Fletcher, Garth L

2007-11-01

Antifreeze proteins (AFP) and antifreeze glycoproteins (AFGP) lower the freezing point of marine fish plasma non-colligatively by specifically adsorbing to certain surfaces of ice crystals, modifying their structure and inhibiting further growth. While the freezing point is lowered, the melting point is unaltered and the difference between the two is termed thermal hysteresis (TH). In pure water, the level of TH is directly related to the intrinsic activity of the specific AF(G)P in solution and to their concentration. Results of this study indicate that when AF(G)P are dissolved in salt solutions, such as NaCl, encompassing the range they could encounter in nature, there is a synergistic enhancement of basal TH that is positively related to the salt concentration. This enhancement is likely a result of the hydration shell surrounding the dissolved ions and, as a consequence, reducing freezable water. A secondary reason for the enhancement is that the salt could be influencing the hydration shell surrounding the AF(G)P, increasing their solubility and thus the protein surface area available to adsorb to the ice/water interface. The former hypothesis for the salt enhanced TH has implications for the in vivo function of AF(G)P, particularly at the seawater/external epithelia (gills, skin, stomach) interface. The latter hypothesis is likely only relevant to in vitro situations where freeze dried protein is dissolved in low salt solutions.

Thermodynamic Investigation of the Effect of Interface Curvature on the Solid-Liquid Equilibrium and Eutectic Point of Binary Mixtures.

PubMed

Liu, Fanghui; Zargarzadeh, Leila; Chung, Hyun-Joong; Elliott, Janet A W

2017-10-12

Thermodynamic phase behavior is affected by curved interfaces in micro- and nanoscale systems. For example, capillary freezing point depression is associated with the pressure difference between the solid and liquid phases caused by interface curvature. In this study, the thermal, mechanical, and chemical equilibrium conditions are derived for binary solid-liquid equilibrium with a curved solid-liquid interface due to confinement in a capillary. This derivation shows the equivalence of the most general forms of the Gibbs-Thomson and Ostwald-Freundlich equations. As an example, the effect of curvature on solid-liquid equilibrium is explained quantitatively for the water/glycerol system. Considering the effect of a curved solid-liquid interface, a complete solid-liquid phase diagram is developed over a range of concentrations for the water/glycerol system (including the freezing of pure water or precipitation of pure glycerol depending on the concentration of the solution). This phase diagram is compared with the traditional phase diagram in which the assumption of a flat solid-liquid interface is made. We show the extent to which nanoscale interface curvature can affect the composition-dependent freezing and precipitating processes, as well as the change in the eutectic point temperature and concentration with interface curvature. Understanding the effect of curvature on solid-liquid equilibrium in nanoscale capillaries has applications in the food industry, soil science, cryobiology, nanoporous materials, and various nanoscience fields.

Dynamics of the Molten Contact Line

NASA Technical Reports Server (NTRS)

Sonin, Ain A.; Schiaffino, Stefano

1996-01-01

In contrast to the ordinary contact line problem, virtually no information is available on the similar problem associated with a molten material spreading on a solid which is below the melt's fusion point. The latter is a more complex problem which heat transfer and solidification take place simultaneously with spreading, and requires answers not only for the hot melt's advance speed over the cold solid as a function of contact angle, but also for how one is to predict the point of the molten contact line's arrest by freezing. This issues are of importance in evolving methods of materials processing. The purpose of our work is to develop, based on both experiments and theory, an understanding of the dynamic processes that occur when a molten droplet touches a subcooled solid, spreads partly over it by capillary action, and freezes. We seek answers to the following basic questions. First, what is the relationship between the melt's contact line speed and the apparent (dynamic) contact angle? Secondly, at what point will the contact line modon be arrested by freezing? The talk will describe three components of our work: (1) deposition experiments with small molten droplets; (2) investigation of the dynamics of the molten contact line by means of a novel forced spreading method; and (3) an attempt to provide a theoretical framework for answering the basic questions posed above.

Osmotic effects of polyethylene glycol.

PubMed

Schiller, L R; Emmett, M; Santa Ana, C A; Fordtran, J S

1988-04-01

Polyethylene glycol (PEG) has been used to increase the osmotic pressure of fluids used to cleanse the gastrointestinal tract. However, little is known about its osmotic activity. To investigate this activity systematically, solutions of PEG of differing molecular weights were made and subjected to measurement of osmolality by both freezing point depression and vapor pressure osmometry. Measured osmolality was increasingly greater than predicted from average molecular weight as PEG concentration increased. Measurement of sodium activity in NaCl/PEG solutions by means of an ion-selective electrode suggested that the higher than expected osmolality could be due in part to interactions that, in effect, sequestered water from the solution. Osmolality was consistently greater by freezing point osmometry than by vapor pressure osmometry. To determine which osmometry method reflected biologically relevant osmolality, normal subjects underwent steady-state total gut perfusion with an electrolyte solution containing 105 g/L of PEG 3350. This produced rectal effluent that was hypertonic by freezing point osmometry but isotonic by vapor pressure osmometry. Assuming that luminal fluid reaches osmotic equilibrium with plasma during total gut perfusion, this result suggests that the vapor pressure osmometer accurately reflects the biologically relevant osmolality of intestinal contents. We conclude that PEG exerts more of an osmotic effect than would be predicted from its molecular weight. This phenomenon may reflect interactions between PEG and water molecules that alter the physical chemistry of the solution and sequester water from the solution.

Preservation of EDTA-expanded grid-mounted chromosomes and nuclei for electron microscopy using a specially designed freeze-dryer.

PubMed

Woods, P S; Ledbetter, M C; Tempel, N

1991-06-01

We describe methods for freezing and drying EDTA-expanded, fixed metaphase chromosomes and nuclei, attached to grids as whole-mounts, for transmission electron microscopy. These methods use a special apparatus that is simple to construct. While separate freezers and dryers are commercially available, one for freezing blocks of tissue by slamming them against a cold metal surface, and the other for vacuum drying the frozen tissue, our apparatus is designed for gentler, cryogenic liquid plunge freezing and drying, sequentially, in the same apparatus, thus avoiding any compression or damage to the specimen. Use of a cryoprotectant is not essential; however, good results are obtained more often when 20% ethanol is used. Freezing is accomplished by rapid propulsion of the grid, with specimens attached, into slushy N2 (-210 degrees C) within the drying chamber; drying is automatic, by either sublimation under vacuum or by solvent substitution using absolute ethanol followed by acetone, which, in turn, is removed with a critical-point dryer. The apparatus offers a means of drying chromosomes and nuclei in an expanded state, and avoids the shrinkage of these structures that occurs during stepwise passage through increasing concentrations of ethanol or acetone.

APMP.T-K3.4: key comparison of realizations of the ITS-90 over the range -38.8344 °C to 419.527 °C

NASA Astrophysics Data System (ADS)

Joung, W.; Gam, K. S.; Achmadi, A.; Trisna, B. A.

2016-01-01

The APMP bilateral key comparison APMP.T-K3.4 was initiated on the request from RCM-LIPI (Indonesia) to link their national standards to the average reference values (ARVs) of the CCT-K3. Korea Research Institute of Standards and Science (KRISS, Republic of Korea) provided the linkage to the CCT-K3 for temperatures ranging from -38.8344 °C to 419.527 °C. In the APMP.T-K3.4, two standard platinum resistance thermometers (SPRTs) were chosen as the transfer instruments and were calibrated at the ITS-90 fixed-points in the comparison range. The fixed-points in this comparison included Zn freezing point (419.527 °C), Sn freezing point (231.928 °C), In freezing point (156.5985 °C), Ga melting point (29.7646 °C), and Hg triple point (-38.8344 °C). The comparison was carried out in a participant-pilot-participant sequence where KRISS served as the pilot. The linkage was based on the fixed-point resistance ratios of RCM-LIPI relative to the ARVs of the CCT-K3 via the difference between the fixed-point resistance ratios of KRISS and the ARVs of the CCT-K3. The temperature differences between the national standards of RCM-LIPI and the ARVs of the CCT-K3 were within the evaluated comparison uncertainties of the ATPM.T-K3.4. This report provides detailed information on the comparison results, linkage mechanism, and the Degree of Equivalence of the RCM-LIPI relative to the institutes having participated in the CCT-K3. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Optimum Temperature for Storage of Fruit and Vegetables with Reference to Chilling Injury

NASA Astrophysics Data System (ADS)

Murata, Takao

Cold storage is an important technique for preserving fresh fruit and vegetables. Deterioration due to ripening, senescence and microbiological disease can be retarded by storage at optimum temperature being slightly above the freezing point of tissues of fruit and vegetables. However, some fruit and vegetables having their origins in tropical or subtropical regions of the world are subject to chilling injury during transportation, storage and wholesale distribution at low temperature above freezing point, because they are usually sensitive to low temperature in the range of 15&digC to 0°C. This review will focus on the recent informations regarding chilling injury of fruit and vegetables, and summarize the optimum temperature for transportation and storage of fruit and vegetables in relation to chilling injury.

Measurement and correlation of jet fuel viscosities at low temperatures

NASA Technical Reports Server (NTRS)

Schruben, D. L.

1985-01-01

Apparatus and procedures were developed to measure jet fuel viscosity for eight current and future jet fuels at temperatures from ambient to near -60 C by shear viscometry. Viscosity data showed good reproducibility even at temperatures a few degrees below the measured freezing point. The viscosity-temperature relationship could be correlated by two linear segments when plotted as a standard log-log type representation (ASTM D 341). At high temperatures, the viscosity-temperature slope is low. At low temperatures, where wax precipitation is significant, the slope is higher. The breakpoint between temperature regions is the filter flow temperature, a fuel characteristic approximated by the freezing point. A generalization of the representation for the eight experimental fuels provided a predictive correlation for low-temperature viscosity, considered sufficiently accurate for many design or performance calculations.

Infrared Thermography for Monitoring of Freeze-Drying Processes: Instrumental Developments and Preliminary Results

PubMed Central

Emteborg, Håkan; Zeleny, Reinhard; Charoud-Got, Jean; Martos, Gustavo; Lüddeke, Jörg; Schellin, Holger; Teipel, Katharina

2014-01-01

Coupling an infrared (IR) camera to a freeze dryer for on-line monitoring of freeze-drying cycles is described for the first time. Normally, product temperature is measured using a few invasive Pt-100 probes, resulting in poor spatial resolution. To overcome this, an IR camera was placed on a process-scale freeze dryer. Imaging took place every 120 s through a Germanium window comprising 30,000 measurement points obtained contact-free from −40°C to 25°C. Results are presented for an empty system, bulk drying of cheese slurry, and drying of 1 mL human serum in 150 vials. During freezing of the empty system, differences of more than 5°C were measured on the shelf. Adding a tray to the empty system, a difference of more than 8°C was observed. These temperature differences probably cause different ice structures affecting the drying speed during sublimation. A temperature difference of maximum 13°C was observed in bulk mode during sublimation. When drying in vials, differences of more than 10°C were observed. Gradually, the large temperature differences disappeared during secondary drying and products were transformed into uniformly dry cakes. The experimental data show that the IR camera is a highly versatile on-line monitoring tool for different kinds of freeze-drying processes. © 2014 European Union 103:2088–2097, 2014 PMID:24902839

Infrared thermography for monitoring of freeze-drying processes: instrumental developments and preliminary results.

PubMed

Emteborg, Håkan; Zeleny, Reinhard; Charoud-Got, Jean; Martos, Gustavo; Lüddeke, Jörg; Schellin, Holger; Teipel, Katharina

2014-07-01

Coupling an infrared (IR) camera to a freeze dryer for on-line monitoring of freeze-drying cycles is described for the first time. Normally, product temperature is measured using a few invasive Pt-100 probes, resulting in poor spatial resolution. To overcome this, an IR camera was placed on a process-scale freeze dryer. Imaging took place every 120 s through a Germanium window comprising 30,000 measurement points obtained contact-free from -40 °C to 25 °C. Results are presented for an empty system, bulk drying of cheese slurry, and drying of 1 mL human serum in 150 vials. During freezing of the empty system, differences of more than 5 °C were measured on the shelf. Adding a tray to the empty system, a difference of more than 8 °C was observed. These temperature differences probably cause different ice structures affecting the drying speed during sublimation. A temperature difference of maximum 13 °C was observed in bulk mode during sublimation. When drying in vials, differences of more than 10 °C were observed. Gradually, the large temperature differences disappeared during secondary drying and products were transformed into uniformly dry cakes. The experimental data show that the IR camera is a highly versatile on-line monitoring tool for different kinds of freeze-drying processes. © 2014 European Union.

Effect of chlorine, blanching, freezing, and microwave heating on Cryptosporidium parvum viability inoculated on green peppers.

PubMed

Duhain, G L M C; Minnaar, A; Buys, E M

2012-05-01

Cryptosporidium parvum oocysts have been found on the surface of vegetables in both developed and developing countries. C. parvum can contaminate vegetables via various routes, including irrigation water. This study investigated the effect of individual treatments of chlorine, blanching, blast freezing, and microwave heating, as well as combined treatments of chlorine and freezing, and chlorine and microwave heating on the viability of C. parvum oocysts inoculated on green peppers. The viability of the oocysts after the treatments was assessed using propidium iodide and a flow cytometer. Based on the propidium iodide staining, the chlorine treatments did not affect the viability of the oocysts. Blast freezing significantly inactivated 20% of the oocysts. Microwave heating and blanching significantly inactivated 93% of oocysts. Treatment with chlorine followed by blast freezing did not affect the viability of the oocysts significantly. Treatment with chlorine and microwave heating was significantly more effective than microwave heating alone and inactivated 98% of the oocysts. The study indicates that C. parvum oocysts are sensitive to heat and, to some extent, to blast freezing, but are resistant to chlorine. Therefore, the use of chlorine during vegetable processing is not a critical control point for C. parvum oocysts, and the consumption of raw or minimally processed vegetables may constitute a health risk as C. parvum oocysts can still be found viable on ready-to-eat, minimally processed vegetables.

Prospective Chemistry Teachers' Misconceptions about Colligative Properties: Boiling Point Elevation and Freezing Point Depression

ERIC Educational Resources Information Center

Pinarbasi, Tacettin; Sozbilir, Mustafa; Canpolat, Nurtac

2009-01-01

This study aimed at identifying prospective chemistry teachers' misconceptions of colligative properties. In order to fulfill this aim, a diagnostic test composed of four open-ended questions was used. The test was administered to seventy-eight prospective chemistry teachers just before qualifying to teaching in secondary schools. Nine different…

Vacuum Processing Technique for Development of Primary Standard Blackbodies

PubMed Central

Navarro, M.; Bruce, S. S.; Johnson, B. Carol; Murthy, A. V.; Saunders, R. D.

1999-01-01

Blackbody sources with nearly unity emittance that are in equilibrium with a pure freezing metal such as gold, silver, or copper are used as primary standard sources in the International Temperature Scale of 1990 (ITS-90). Recently, a facility using radio-frequency induction heating for melting and filling the blackbody crucible with the freeze metal under vacuum conditions was developed at the National Institute of Standards and Technology (NIST). The blackbody development under a vacuum environment eliminated the possibility of contamination of the freeze metal during the process. The induction heating, compared to a resistively heated convection oven, provided faster heating of crucible and resulted in shorter turn-around time of about 7 h to manufacture a blackbody. This paper describes the new facility and its application to the development of fixed-point blackbodies.

Sorted clastic stripes, lobes and associated gullies in high-latitude craters on Mars: Landforms indicative of very recent, polycyclic ground-ice thaw and liquid flows

NASA Astrophysics Data System (ADS)

Gallagher, C.; Balme, M. R.; Conway, S. J.; Grindrod, P. M.

2011-01-01

Self-organised patterns of stone stripes, polygons, circles and clastic solifluction lobes form by the sorting of clasts from fine-grained sediments in freeze-thaw cycles. We present new High Resolution Imaging Science Experiment (HiRISE) images of Mars which demonstrate that the slopes of high-latitude craters, including Heimdal crater - just 25 km east of the Phoenix Landing Site - are patterned by all of these landforms. The order of magnitude improvement in imaging data resolution afforded by HiRISE over previous datasets allows not only the reliable identification of these periglacial landforms but also shows that high-latitude fluviatile gullies both pre- and post-date periglacial patterned ground in several high-latitude settings on Mars. Because thaw is inherent to the sorting processes that create these periglacial landforms, and from the association of this landform assemblage with fluviatile gullies, we infer the action of liquid water in a fluvio-periglacial context. We conclude that these observations are evidence of the protracted, widespread action of thaw liquids on and within the martian regolith. Moreover, the size frequency statistics of superposed impact craters demonstrate that this freeze-thaw environment is, at least in Heimdal crater, less than a few million years old. Although the current martian climate does not favour prolonged thaw of water ice, observations of possible liquid droplets on the strut of the Phoenix Lander may imply significant freezing point depression of liquids sourced in the regolith, probably driven by the presence of perchlorates in the soil. Because perchlorates have eutectic temperatures below 240 K and can remain liquid at temperatures far below the freezing point of water we speculate that freeze-thaw involving perchlorate brines provides an alternative "low-temperature" hypothesis to the freeze-thaw of more pure water ice and might drive significant geomorphological work in some areas of Mars. Considering the proximity of Heimdal crater to the Phoenix Landing Site, the presence of such hydrated minerals might therefore explain the landforms described here. If this is the case then the geographical distribution of martian freeze-thaw landforms might reflect relatively high temperatures (but still below 273 K) and the locally elevated concentration of salts in the regolith.

Influence of the Cavity Length on the Behavior of Hybrid Fixed-Point Cells Constructed at INRIM

NASA Astrophysics Data System (ADS)

Battuello, M.; Girard, F.; Florio, M.

2015-03-01

Hybrid cells with double carbon/carbon sheets are used at the Istituto Nazionale di Ricerca Metrologica (INRIM) for the realization of both pure metal fixed points and high-temperature metal-carbon eutectic points. Cells for the Cu and Co-C fixed points have been prepared to be used in the high-temperature fixed-point project of the Comité Consultatif de Thermométrie. The results of the evaluation processes were not completely satisfactory for the INRIM cells because of their low transition temperatures with respect to the best cells, and of a rather large melting range for the Co-C cell. A new design of the cells was devised, and considerable improvements were achieved with respect to the transition temperature, and the plateau shape and duration. As for the Cu point, the duration of the freezing plateaux increased by more than 50 % and the freezing temperature increased by 18 mK. As for the Co-C point, the melting temperature, expressed in terms of the point of inflection of the melting curve, increased by about 70 mK. The melting range of the plateaux, expressed as a difference was reduced from about 180 mK to about 130 mK, with melting times increased by about 50 %, as a consequence of an improvement of flatness and run-off of the plateaux.

Dendrimer-Linked Antifreeze Proteins Have Superior Activity and Thermal Recovery.

PubMed

Stevens, Corey A; Drori, Ran; Zalis, Shiran; Braslavsky, Ido; Davies, Peter L

2015-09-16

By binding to ice, antifreeze proteins (AFPs) depress the freezing point of a solution and inhibit ice recrystallization if freezing does occur. Previous work showed that the activity of an AFP was incrementally increased by fusing it to another protein. Even larger increases in activity were achieved by doubling the number of ice-binding sites by dimerization. Here, we have combined the two strategies by linking multiple outward-facing AFPs to a dendrimer to significantly increase both the size of the molecule and the number of ice-binding sites. Using a heterobifunctional cross-linker, we attached between 6 and 11 type III AFPs to a second-generation polyamidoamine (G2-PAMAM) dendrimer with 16 reactive termini. This heterogeneous sample of dendrimer-linked type III constructs showed a greater than 4-fold increase in freezing point depression over that of monomeric type III AFP. This multimerized AFP was particularly effective at ice recrystallization inhibition activity, likely because it can simultaneously bind multiple ice surfaces. Additionally, attachment to the dendrimer has afforded the AFP superior recovery from heat denaturation. Linking AFPs together via polymers can generate novel reagents for controlling ice growth and recrystallization.

Comparison of three-dimensional printing and vacuum freeze-dried techniques for fabricating composite scaffolds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Kai; Li, Ruixin; Jiang, Wenxue, E-mail: jiangortholivea@sina.cn

In this study, the performances of different preparation methods of the scaffolds were analyzed for chondrocyte tissue engineering. Silk fibroin/collagen (SF/C) was fabricated using a vacuum freeze-dried technique and by 3D printing. The porosity, water absorption expansion rates, mechanical properties, and pore sizes of the resulting materials were evaluated. The proliferation and metabolism of the cells was detected at different time points using an MTT assay. Cell morphologies and distributions were observed by histological analysis and scanning electron microscopy (SEM). The porosity, water absorption expansion rate, and Young’s modulus of the material obtained via 3D printing were significantly higher thanmore » those obtained by the freeze-dried method, while the pore size did not differ significantly between the two methods. MTT assay results showed that the metabolism of cells seeded on the 3D printed scaffolds was more viable than the metabolism on the freeze-dried material. H&E staining of the scaffolds revealed that the number of cells in the 3D printed scaffold was higher in comparison to a similar measurement on the freeze-dried material. Consequently, stem cells grew well inside the 3D printed scaffolds, as measured by SEM, while the internal structure of the freeze-dried scaffold was disordered. Compared with the freeze-dried technique, the 3D printed scaffold exhibited better overall performance and was more suitable for cartilage tissue engineering. - Highlights: • Silk fibroin/collagen was fabricated using 3D printing. • Physical characterization and Cell compatibility were compared. • 3D printed scaffold exhibited better overall performance.« less

Validity of a portable urine refractometer: the effects of sample freezing.

PubMed

Sparks, S Andy; Close, Graeme L

2013-01-01

The use of portable urine osmometers is widespread, but no studies have assessed the validity of this measurement technique. Furthermore, it is unclear what effect freezing has on osmolality. One-hundred participants of mean (±SD) age 25.1 ± 7.6 years, height 1.77 ± 0.1 m and weight 77.1 ± 10.8 kg provided single urine samples that were analysed using freeze point depression (FPD) and refractometry (RI). Samples were then frozen at -80°C (n = 81) and thawed prior to re-analysis. Differences between methods and freezing were determined using Wilcoxon's signed rank test. Relationships between measurements were assessed using intraclass correlation coefficients (ICC) and typical error of estimate (TE). Osmolality was lower (P = 0.001) using RI (634.2 ± 339.8 mOsm · kgH2O(-1)) compared with FPD (656.7 ± 334.1 mOsm · kgH2O(-1)) but the TE was trivial (0.17). Freezing significantly reduced mean osmolality using FPD (656.7 ± 341.1 to 606.5 ± 333.4 mOsm · kgH2O(-1); P < 0.001), but samples were still highly related following freezing (ICC, r = 0.979, P < 0.001, CI = 0.993-0.997; TE = 0.15; and r=0.995, P < 0.001, CI = 0.967-0.986; TE = 0.07 for RI and FPD respectively). Despite mean differences between methods and as a result of freezing, such differences are physiologically trivial. Therefore, the use of RI appears to be a valid measurement tool to determine urine osmolality.

Molecular dynamics of acetamide based ionic deep eutectic solvents

NASA Astrophysics Data System (ADS)

Srinivasan, H.; Dubey, P. S.; Sharma, V. K.; Biswas, R.; Mitra, S.; Mukhopadhyay, R.

2018-04-01

Deep eutectic solvents are multi-component mixtures that have freezing point lower than their individual components. Mixture of acetamide+ lithium nitrate in the molar ratio 78:22 and acetamide+ lithium perchlorate in the molar ratio 81:19 are found to form deep eutectic solvents with melting point lower than the room temperature. It is known that the depression in freezing point is due to the hydrogen bond breaking ability of anions in the system. Quasielastic neutron scattering experiments on these systems were carried out to study the dynamics of acetamide molecules which may be influenced by this hydrogen bond breaking phenomena. The motion of acetamide molecules is modeled using jump diffusion mechanism to demonstrate continuous breaking and reforming hydrogen bonds in the solvent. Using the jump diffusion model, it is inferred that the jump lengths of acetamide molecules are better approximated by a Gaussian distribution. The shorter residence time of acetamide in presence of perchlorate ions suggest that the perchlorate ions have a higher hydrogen bond breaking ability compared to nitrate ions.

A water activity based model of heterogeneous ice nucleation kinetics for freezing of water and aqueous solution droplets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knopf, Daniel A.; Alpert, Peter A.

Immersion freezing of water and aqueous solutions by particles acting as ice nuclei (IN) is a common process of heterogeneous ice nucleation which occurs in many environments, especially in the atmosphere where it results in the glaciation of clouds. Here we experimentally show, using a variety of IN types suspended in various aqueous solutions, that immersion freezing temperatures and kinetics can be described solely by temperature, T, and solution water activity, aw, which is the ratio of the vapour pressure of the solution and the saturation water vapour pressure under the same conditions and, in equilibrium, equivalent to relative humiditymore » (RH). This allows the freezing point and corresponding heterogeneous ice nucleation rate coefficient, Jhet, to be uniquely expressed by T and aw, a result we term the aw based immersion freezing model (ABIFM). This method is independent of the nature of the solute and accounts for several varying parameters, including cooling rate and IN surface area, while providing a holistic description of immersion freezing and allowing prediction of freezing temperatures, Jhet, frozen fractions, ice particle production rates and numbers. Our findings are based on experimental freezing data collected for various IN surface areas, A, and cooling rates, r, of droplets variously containing marine biogenic material, two soil humic acids, four mineral dusts, and one organic monolayer acting as IN. For all investigated IN types we demonstrate that droplet freezing temperatures increase as A increases. Similarly, droplet freezing temperatures increase as the cooling rate decreases. The log 10(J het) values for the various IN types derived exclusively by T and aw, provide a complete description of the heterogeneous ice nucleation kinetics. Thus, the ABIFM can be applied over the entire range of T, RH, total particulate surface area, and cloud activation timescales typical of atmospheric conditions. Finally, we demonstrate that ABIFM can be used to derive frozen fractions of droplets and ice particle production for atmospheric models of cirrus and mixed phase cloud conditions.« less

A water activity based model of heterogeneous ice nucleation kinetics for freezing of water and aqueous solution droplets.

PubMed

Knopf, Daniel A; Alpert, Peter A

2013-01-01

Immersion freezing of water and aqueous solutions by particles acting as ice nuclei (IN) is a common process of heterogeneous ice nucleation which occurs in many environments, especially in the atmosphere where it results in the glaciation of clouds. Here we experimentally show, using a variety of IN types suspended in various aqueous solutions, that immersion freezing temperatures and kinetics can be described solely by temperature, T, and solution water activity, a(w), which is the ratio of the vapour pressure of the solution and the saturation water vapour pressure under the same conditions and, in equilibrium, equivalent to relative humidity (RH). This allows the freezing point and corresponding heterogeneous ice nucleation rate coefficient, J(het), to be uniquely expressed by T and a(w), a result we term the a(w) based immersion freezing model (ABIFM). This method is independent of the nature of the solute and accounts for several varying parameters, including cooling rate and IN surface area, while providing a holistic description of immersion freezing and allowing prediction of freezing temperatures, J(het), frozen fractions, ice particle production rates and numbers. Our findings are based on experimental freezing data collected for various IN surface areas, A, and cooling rates, r, of droplets variously containing marine biogenic material, two soil humic acids, four mineral dusts, and one organic monolayer acting as IN. For all investigated IN types we demonstrate that droplet freezing temperatures increase as A increases. Similarly, droplet freezing temperatures increase as the cooling rate decreases. The log10(J(het)) values for the various IN types derived exclusively by Tand a(w), provide a complete description of the heterogeneous ice nucleation kinetics. Thus, the ABIFM can be applied over the entire range of T, RH, total particulate surface area, and cloud activation timescales typical of atmospheric conditions. Lastly, we demonstrate that ABIFM can be used to derive frozen fractions of droplets and ice particle production for atmospheric models of cirrus and mixed phase cloud conditions.

A water activity based model of heterogeneous ice nucleation kinetics for freezing of water and aqueous solution droplets

DOE PAGES

Knopf, Daniel A.; Alpert, Peter A.

2013-04-24

Immersion freezing of water and aqueous solutions by particles acting as ice nuclei (IN) is a common process of heterogeneous ice nucleation which occurs in many environments, especially in the atmosphere where it results in the glaciation of clouds. Here we experimentally show, using a variety of IN types suspended in various aqueous solutions, that immersion freezing temperatures and kinetics can be described solely by temperature, T, and solution water activity, aw, which is the ratio of the vapour pressure of the solution and the saturation water vapour pressure under the same conditions and, in equilibrium, equivalent to relative humiditymore » (RH). This allows the freezing point and corresponding heterogeneous ice nucleation rate coefficient, Jhet, to be uniquely expressed by T and aw, a result we term the aw based immersion freezing model (ABIFM). This method is independent of the nature of the solute and accounts for several varying parameters, including cooling rate and IN surface area, while providing a holistic description of immersion freezing and allowing prediction of freezing temperatures, Jhet, frozen fractions, ice particle production rates and numbers. Our findings are based on experimental freezing data collected for various IN surface areas, A, and cooling rates, r, of droplets variously containing marine biogenic material, two soil humic acids, four mineral dusts, and one organic monolayer acting as IN. For all investigated IN types we demonstrate that droplet freezing temperatures increase as A increases. Similarly, droplet freezing temperatures increase as the cooling rate decreases. The log 10(J het) values for the various IN types derived exclusively by T and aw, provide a complete description of the heterogeneous ice nucleation kinetics. Thus, the ABIFM can be applied over the entire range of T, RH, total particulate surface area, and cloud activation timescales typical of atmospheric conditions. Finally, we demonstrate that ABIFM can be used to derive frozen fractions of droplets and ice particle production for atmospheric models of cirrus and mixed phase cloud conditions.« less

An Investigation on the Thermophysical Properties of a Binary Molten Salt System Containing Both Aluminum Oxide and Titanium Oxide Nanoparticle Suspensions

NASA Astrophysics Data System (ADS)

Giridhar, Kunal

Molten salts are showing great potential to replace current heat transfer and thermal energy storage fluids in concentrated solar plants because of their capability to maximize thermal energy storage, greater stability, cost effectiveness and significant thermal properties. However one of the major drawbacks of using molten salt as heat transfer fluid is that they are in solid state at room temperature and they have a high freezing point. Hence, significant resources would be required to maintain it in liquid form. If molten salt freezes while in operation, it would eventually damage piping network due to its volume shrinkage along with rendering the entire plant inoperable. It is long known that addition of nanoparticle suspensions has led to significant changes in thermal properties of fluids. In this investigation, aluminum oxide and titanium oxide nanoparticles of varying concentrations are added to molten salt/solar salt system consisting of 60% sodium nitrate and 40% potassium nitrate. Using differential scanning calorimeter, an attempt will be made to investigate changes in heat capacity of system, depression in freezing point and changes in latent heat of fusion. Scanning electron microscope will be used to take images of samples to study changes in micro-structure of mixture, ensure uniform distribution of nanoparticle in system and verify authenticity of materials used for experimentation. Due to enormous magnitude of CSP plant, actual implementation of molten salt system is on a large scale. With this investigation, even microscopic enhancement in heat capacity and slight lowering of freezing point will lead to greater benefits in terms of efficiency and cost of operation of plant. These results will further the argument for viability of molten salt as a heat transfer fluid and thermal storage system in CSP. One of the objective of this experimentation is to also collect experimental data which can be used for establishing relation between concentration of nanoparticles and change in thermophysical properties of molten salt for various types of nanoparticles.

Dynamic Demos.

ERIC Educational Resources Information Center

Sae, Andy S. W.

1991-01-01

Discusses 27 chemical demonstrations involving inexpensive, readily available materials that illustrate the following concepts: acid/base properties, gas properties, characteristics of carbon dioxide, chemiluminescence, freezing point depression, heat of vaporization; density, polymers, surface tension, polarity/nonpolarity, UV absorption,…

14 CFR 29.1013 - Oil tanks.

Code of Federal Regulations, 2013 CFR

2013-01-01

... effective under all normal flight conditions. (2) Oil tank vents must be arranged so that condensed water vapor that might freeze and obstruct the line cannot accumulate at any point; (e) Outlet. There must be...

14 CFR 29.1013 - Oil tanks.

Code of Federal Regulations, 2012 CFR

2012-01-01

... effective under all normal flight conditions. (2) Oil tank vents must be arranged so that condensed water vapor that might freeze and obstruct the line cannot accumulate at any point; (e) Outlet. There must be...

14 CFR 29.1013 - Oil tanks.

Code of Federal Regulations, 2014 CFR

2014-01-01

... effective under all normal flight conditions. (2) Oil tank vents must be arranged so that condensed water vapor that might freeze and obstruct the line cannot accumulate at any point; (e) Outlet. There must be...

14 CFR 29.1013 - Oil tanks.

Code of Federal Regulations, 2010 CFR

2010-01-01

... effective under all normal flight conditions. (2) Oil tank vents must be arranged so that condensed water vapor that might freeze and obstruct the line cannot accumulate at any point; (e) Outlet. There must be...

14 CFR 29.1013 - Oil tanks.

Code of Federal Regulations, 2011 CFR

2011-01-01

... effective under all normal flight conditions. (2) Oil tank vents must be arranged so that condensed water vapor that might freeze and obstruct the line cannot accumulate at any point; (e) Outlet. There must be...

Development of a low temperature phase change material package. [for spacecraft thermal control

NASA Technical Reports Server (NTRS)

Brennan, P. J.; Suelau, H. J.; Mcintosh, R.

1977-01-01

Test data obtained for a low temperature phase change material (PCM) canisters are presented. The canister was designed to provide up to 30 w-hrs of storage capacity at approximately -90 C with an overall thermal conductance which is greater than 8 w/deg C. N-heptane which is an n-paraffin and has a -90.6 C freezing point was used as the working fluid. The canister was fabricated from aluminum and has an aluminum honeycomb core. Its void volume permits service temperatures up to 70 C. Results obtained from component and system's tests indicate well defined melting and freezing points which are repeatable and within 1 C of each other. Subcooling effects are less than 0.5 C and are essentially negligible. Measured storage capacities are within 94 to 88% the theoretical.

Cross-validation of the osmotic pressure based on Pitzer model with air humidity osmometry at high concentration of ammonium sulfate solutions.

PubMed

Wang, Xiao-Lan; Zhan, Ting-Ting; Zhan, Xian-Cheng; Tan, Xiao-Ying; Qu, Xiao-You; Wang, Xin-Yue; Li, Cheng-Rong

2014-01-01

The osmotic pressure of ammonium sulfate solutions has been measured by the well-established freezing point osmometry in dilute solutions and we recently reported air humidity osmometry in a much wider range of concentration. Air humidity osmometry cross-validated the theoretical calculations of osmotic pressure based on the Pitzer model at high concentrations by two one-sided test (TOST) of equivalence with multiple testing corrections, where no other experimental method could serve as a reference for comparison. Although more strict equivalence criteria were established between the measurements of freezing point osmometry and the calculations based on the Pitzer model at low concentration, air humidity osmometry is the only currently available osmometry applicable to high concentration, serves as an economic addition to standard osmometry.

Use of manometric temperature measurement (MTM) and SMART freeze dryer technology for development of an optimized freeze-drying cycle.

PubMed

Gieseler, Henning; Kramer, Tony; Pikal, Michael J

2007-12-01

This report provides, for the first time, a summary of experiments using SMART Freeze Dryer technology during a 9 month testing period. A minimum ice sublimation area of about 300 cm(2) for the laboratory freeze dryer, with a chamber volume 107.5 L, was found consistent with data obtained during previous experiments with a smaller freeze dryer (52 L). Good reproducibility was found for cycle design with different type of excipients, formulations, and vials used. SMART primary drying end point estimates were accurate in the majority of the experiments, but showed an over prediction of primary cycle time when the product did not fully achieve steady state conditions before the first MTM measurement was performed. Product resistance data for 5% sucrose mixtures at varying fill depths were very reproducible. Product temperature determined by SMART was typically in good agreement with thermocouple data through about 50% of primary drying time, with significant deviations occurring near the end of primary drying, as expected, but showing a bias much earlier in primary drying for high solid content formulations (16.6% Pfizer product) and polyvinylpyrrolidone (40 kDa) likely due to water "re-adsorption" by the amorphous product during the MTM test. (c) 2007 Wiley-Liss, Inc.

Are superhydrophobic surfaces best for icephobicity?

PubMed

Jung, Stefan; Dorrestijn, Marko; Raps, Dominik; Das, Arindam; Megaridis, Constantine M; Poulikakos, Dimos

2011-03-15

Ice formation can have catastrophic consequences for human activity on the ground and in the air. Here we investigate water freezing delays on untreated and coated surfaces ranging from hydrophilic to superhydrophobic and use these delays to evaluate icephobicity. Supercooled water microdroplets are inkjet-deposited and coalesce until spontaneous freezing of the accumulated mass occurs. Surfaces with nanometer-scale roughness and higher wettability display unexpectedly long freezing delays, at least 1 order of magnitude longer than typical superhydrophobic surfaces with larger hierarchical roughness and low wettability. Directly related to the main focus on heterogeneous nucleation and freezing delay of supercooled water droplets, the observed ensuing crystallization process consisted of two distinct phases: one very rapid recalescent partial solidification phase and a subsequent slower phase. Observations of the droplet collision process employed for the continuous liquid mass accumulation up to the point of ice formation reveal a previously unseen atmospheric-pressure, subfreezing-temperature regime for liquid-on-liquid bounce. On the basis of the entropy reduction of water near a solid surface, we formulate a modification to the classical heterogeneous nucleation theory, which predicts the observed freezing delay trends. Our results bring to question recent emphasis on super water-repellent surface formulations for ice formation retardation and suggest that anti-icing design must optimize the competing influences of both wettability and roughness.

Freezing of Water Droplet due to Evaporation

NASA Astrophysics Data System (ADS)

Satoh, Isao; Fushinobu, Kazuyoshi; Hashimoto, Yu

In this study, the feasibility of cooling/freezing of phase change.. materials(PCMs) due to evaporation for cold storage systems was experimentally examined. A pure water was used as the test PCM, since the latent heat due to evaporation of water is about 7 times larger than that due to freezing. A water droplet, the diameter of which was 1-4 mm, was suspended in a test cell by a fine metal wire (O. D.= 100μm),and the cell was suddenly evacuated up to the pressure lower than the triple-point pressure of water, so as to enhance the evaporation from the water surface. Temperature of the droplet was measured by a thermocouple, and the cooling/freezing behavior and the temperature profile of the droplet surface were captured by using a video camera and an IR thermo-camera, respectively. The obtained results showed that the water droplet in the evacuated cell is effectively cooled by the evaporation of water itself, and is frozen within a few seconds through remarkable supercooling state. When the initial temperature of the droplet is slightly higher than the room temperature, boiling phenomena occur in the droplet simultaneously with the freezing due to evaporation. Under such conditions, it was shown that the degree of supercooling of the droplet is reduced by the bubbles generated in the droplet.

Freezing in the Antarctic limpet, Nacella concinna.

PubMed

Hawes, T C; Worland, M R; Bale, J S

2010-08-01

The process of organismal freezing in the Antarctic limpet, Nacella concinna, is complicated by molluscan biology. Internal ice formation is, in particular, mediated by two factors: (a) the provision of an inoculative target for ice formation in the exposed mucus-secreting foot; and (b) osmoconformity to the marine environment. With regard to the first, direct observations of the independent freezing of pedal mucus support the hypothesis that internal ice formation is delayed by the mucal film. As to the second, ice nucleation parametrics of organismal tissue (head, midgut, gonad, foot) and mucus in both inter- and subtidal populations were characterized by high melting points (range=-4.61 to -6.29 degrees C), with only c.50% of a given sample osmotically active. At this stage it would be premature to ascribe a cryo-adaptive function to the mucus as the protective effects are more readily attributed to the physical properties of the secretion (i.e. viscosity) and their corresponding effects on the rate of heat transfer. As it is difficult to thermally distinguish between the freezing of mucus and the rest of the animal, the question as to whether it is tolerant of internal as well as external ice formation remains problematic, although it may be well suited to the osmotic stresses of organismal freezing. (c) 2010 Elsevier Inc. All rights reserved.

In-line multipoint near-infrared spectroscopy for moisture content quantification during freeze-drying.

PubMed

Kauppinen, Ari; Toiviainen, Maunu; Korhonen, Ossi; Aaltonen, Jaakko; Järvinen, Kristiina; Paaso, Janne; Juuti, Mikko; Ketolainen, Jarkko

2013-02-19

During the past decade, near-infrared (NIR) spectroscopy has been applied for in-line moisture content quantification during a freeze-drying process. However, NIR has been used as a single-vial technique and thus is not representative of the entire batch. This has been considered as one of the main barriers for NIR spectroscopy becoming widely used in process analytical technology (PAT) for freeze-drying. Clearly it would be essential to monitor samples that reliably represent the whole batch. The present study evaluated multipoint NIR spectroscopy for in-line moisture content quantification during a freeze-drying process. Aqueous sucrose solutions were used as model formulations. NIR data was calibrated to predict the moisture content using partial least-squares (PLS) regression with Karl Fischer titration being used as a reference method. PLS calibrations resulted in root-mean-square error of prediction (RMSEP) values lower than 0.13%. Three noncontact, diffuse reflectance NIR probe heads were positioned on the freeze-dryer shelf to measure the moisture content in a noninvasive manner, through the side of the glass vials. The results showed that the detection of unequal sublimation rates within a freeze-dryer shelf was possible with the multipoint NIR system in use. Furthermore, in-line moisture content quantification was reliable especially toward the end of the process. These findings indicate that the use of multipoint NIR spectroscopy can achieve representative quantification of moisture content and hence a drying end point determination to a desired residual moisture level.

Modelling infiltration processes in frozen soils

NASA Astrophysics Data System (ADS)

Ireson, A. M.; Barbour, L. S.

2014-12-01

Understanding the hydrological processes in soils subject to significant freeze-thaw is fraught by "experimental vagaries and theoretical imponderables" (Miller 1980, Applications of soil physics). The infiltration of snowmelt water and the subsequent transmission of unfrozen water during thawing, is governed by hydraulic conductivity values which are changing with both ice and unfrozen water content. Water held within pores is subject to capillary forces, which results in a freezing point depression (i.e. water remains in the liquid state slightly below 0°C). As the temperature drops below zero, water freezes first in the larger pores, and then in progressively smaller pores. Since the larger pores also are the first to empty by drainage, these pores may be air filled during freezing, while smaller water filled pores freeze. This explains why an unsaturated, frozen soil may still have a considerable infiltration capacity. Infiltration into frozen soil is a critical phenomena related to the risk of flooding in the Canadian prairies, controlling the partitioning of snowmelt into either infiltration or runoff. We propose a new model, based on conceptualizing the pore space as a bundle of capillary tubes (with significant differences to the capillary bundle model of Wannatabe and Flury, 2008, WRR, doi:10.1029/2008WR007102) which allows any air-filled macropores to contribute to the potential infiltration capacity of the soil. The patterns of infiltration and water movement during freeze-thaw from the model are compared to field observations from the Canadian prairies and Boreal Plains.

Nanoscale capillary freezing of ionic liquids confined between metallic interfaces and the role of electronic screening

PubMed Central

Comtet, Jean; Niguès, Antoine; Kaiser, Vojtech; Coasne, Benoit; Bocquet, Lydéric; Siria, Alessandro

2017-01-01

Room temperature Ionic liquids (RTIL) are new materials with fundamental importance for energy storage and active lubrication. They are unsual liquids, which challenge the classical frameworks of electrolytes, whose behavior at electrified interfaces remains elusive with exotic responses relevant to their electrochemical activity. By means of tuning fork based AFM nanorheological measurements, we explore here the properties of confined RTIL, unveiling a dramatic change of the RTIL towards a solid-like phase below a threshold thickness, pointing to capillary freezing in confinement. This threshold is related to the metallic nature of the confining materials, with more metallic surfaces facilitating freezing. This is interpreted in terms of the shift of freezing transition, taking into account the influence of the electronic screening on RTIL wetting of the confining surfaces. Our findings provide fresh views on the properties of confined RTIL with implications for their properties inside nanoporous metallic structures and suggests applications to tune nanoscale lubrication with phase-changing RTIL, by varying the nature and patterning of the substrate, and application of active polarisation. PMID:28346432

Cryoprotectant redistribution along the frozen straw probed by Raman spectroscopy.

PubMed

Karpegina, Yu A; Okotrub, K A; Brusentsev, E Yu; Amstislavsky, S Ya; Surovtsev, N V

2016-04-01

The distribution of cryoprotectant (10% glycerol) and ice along the frozen plastic straw (the most useful container for freezing mammalian semen, oocytes and embryos) was studied by Raman scattering technique. Raman spectroscopy being a contactless, non-invasive tool was applied for the straws filled with the cryoprotectant solution and frozen by controlled rate programs commonly used for mammalian embryos freezing. Analysis of Raman spectra measured at different points along the straw reveals a non-uniform distribution of the cryoprotectant. The ratio between non-crystalline solution and ice was found to be increased by several times at the bottom side of the solution column frozen by the standard freezing program. The increase of the cryoprotectant fraction occurs in the area where embryos or oocytes are normally placed during their freezing. Possible effects of the cooling rate and the ice nucleation temperature on the cryoprotectant fraction at the bottom side of the solution column were considered. Our findings highlight that the ice fraction around cryopreserved embryos or oocytes can differ significantly from the averaged one in the frozen plastic straws. Copyright © 2016 Elsevier Inc. All rights reserved.

Cryoprotection from lipoteichoic acid

NASA Astrophysics Data System (ADS)

Rice, Charles V.; Middaugh, Amy; Wickham, Jason R.; Friedline, Anthony; Thomas, Kieth J.; Johnson, Karen; Zachariah, Malcolm; Garimella, Ravindranth

2012-10-01

Numerous chemical additives lower the freezing point of water, but life at sub-zero temperatures is sustained by a limited number of biological cryoprotectants. Antifreeze proteins in fish, plants, and insects provide protection to a few degrees below freezing. Microbes have been found to survive at even lower temperatures, and with a few exceptions, antifreeze proteins are missing. Survival has been attributed to external factors, such as the high salt concentration of brine veins and adhesion to particulates or ice crystal defects. We have discovered an endogenous cryoprotectant in the cell wall of bacteria, lipoteichoic acid biopolymers. Adding 1% LTA to bacteria cultures immediately prior to freezing provides 50% survival rate, similar to the results obtained with 1% glycerol. In the absence of an additive, bacterial survival is negligible as measured with the resazurin cell viability assay. The mode of action for LTA cryoprotection is unknown. With a molecular weight of 3-5 kDa, it is unlikely to enter the cell cytoplasm. Our observations suggest that teichoic acids could provide a shell of liquid water around biofilms and planktonic bacteria, removing the need for brine veins to prevent bacterial freezing.

Nanoscale capillary freezing of ionic liquids confined between metallic interfaces and the role of electronic screening.

PubMed

Comtet, Jean; Niguès, Antoine; Kaiser, Vojtech; Coasne, Benoit; Bocquet, Lydéric; Siria, Alessandro

2017-06-01

Room-temperature ionic liquids (RTILs) are new materials with fundamental importance for energy storage and active lubrication. They are unusual liquids, which challenge the classical frameworks of electrolytes, whose behaviour at electrified interfaces remains elusive, with exotic responses relevant to their electrochemical activity. Using tuning-fork-based atomic force microscope nanorheological measurements, we explore here the properties of confined RTILs, unveiling a dramatic change of the RTIL towards a solid-like phase below a threshold thickness, pointing to capillary freezing in confinement. This threshold is related to the metallic nature of the confining materials, with more metallic surfaces facilitating freezing. This behaviour is interpreted in terms of the shift of the freezing transition, taking into account the influence of the electronic screening on RTIL wetting of the confining surfaces. Our findings provide fresh views on the properties of confined RTIL with implications for their properties inside nanoporous metallic structures, and suggests applications to tune nanoscale lubrication with phase-changing RTILs, by varying the nature and patterning of the substrate, and application of active polarization.

Nanoscale capillary freezing of ionic liquids confined between metallic interfaces and the role of electronic screening

NASA Astrophysics Data System (ADS)

Comtet, Jean; Niguès, Antoine; Kaiser, Vojtech; Coasne, Benoit; Bocquet, Lydéric; Siria, Alessandro

2017-06-01

Room-temperature ionic liquids (RTILs) are new materials with fundamental importance for energy storage and active lubrication. They are unusual liquids, which challenge the classical frameworks of electrolytes, whose behaviour at electrified interfaces remains elusive, with exotic responses relevant to their electrochemical activity. Using tuning-fork-based atomic force microscope nanorheological measurements, we explore here the properties of confined RTILs, unveiling a dramatic change of the RTIL towards a solid-like phase below a threshold thickness, pointing to capillary freezing in confinement. This threshold is related to the metallic nature of the confining materials, with more metallic surfaces facilitating freezing. This behaviour is interpreted in terms of the shift of the freezing transition, taking into account the influence of the electronic screening on RTIL wetting of the confining surfaces. Our findings provide fresh views on the properties of confined RTIL with implications for their properties inside nanoporous metallic structures, and suggests applications to tune nanoscale lubrication with phase-changing RTILs, by varying the nature and patterning of the substrate, and application of active polarization.

Drying techniques for the visualisation of agarose-based chromatography media by scanning electron microscopy.

PubMed

Nweke, Mauryn C; Turmaine, Mark; McCartney, R Graham; Bracewell, Daniel G

2017-03-01

The drying of chromatography resins prior to scanning electron microscopy is critical to image resolution and hence understanding of the bead structure at sub-micron level. Achieving suitable drying conditions is especially important with agarose-based chromatography resins, as over-drying may cause artefact formation, bead damage and alterations to ultrastructural properties; and under-drying does not provide sufficient resolution for visualization under SEM. This paper compares and contrasts the effects of two drying techniques, critical point drying and freeze drying, on the morphology of two agarose based resins (MabSelect™/d w ≈85 µm and Capto™ Adhere/d w ≈75 µm) and provides a complete method for both. The results show that critical point drying provides better drying and subsequently clearer ultrastructural visualization of both resins under SEM. Under this protocol both the polymer fibers (thickness ≈20 nm) and the pore sizes (diameter ≈100 nm) are clearly visible. Freeze drying is shown to cause bead damage to both resins, but to different extents. MabSelect resin encounters extensive bead fragmentation, whilst Capto Adhere resin undergoes partial bead disintegration, corresponding with the greater extent of agarose crosslinking and strength of this resin. While freeze drying appears to be the less favorable option for ultrastructural visualization of chromatography resin, it should be noted that the extent of fracturing caused by the freeze drying process may provide some insight into the mechanical properties of agarose-based chromatography media. © 2017 The Authors. Biotechnology Journal published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cold hardiness of emerald ash borer, Agrilus planipennis: a new perspective

Treesearch

Robert C. Venette; Mark Abrahamson

2010-01-01

This study was designed to assess the cold hardiness of emerald ash borer larvae, the overwintering stage of the insect. We began by measuring larval supercooling points, the temperatures at which larvae freeze. We found that larvae collected from naturally infested trees in St. Paul, MN between late October and early December had an average supercooling point of -25...

About the International System of Units (SI) Part II. Organization and General Principles

ERIC Educational Resources Information Center

Aubrecht, Gordon J., II; French, Anthony P.; Iona, Mario

2011-01-01

As all physicists know, all units are arbitrary. The numbering system is anthropocentric; for example, the Celsius scale of temperature has 100 degrees between the boiling point of water at STP and the freezing point of water. The number 100 is chosen because human beings have 10 fingers. The best units might be based on physical constants, for…

Optimisation of phenolic extraction from Averrhoa carambola pomace by response surface methodology and its microencapsulation by spray and freeze drying.

PubMed

Saikia, Sangeeta; Mahnot, Nikhil Kumar; Mahanta, Charu Lata

2015-03-15

Optimised of the extraction of polyphenol from star fruit (Averrhoa carambola) pomace using response surface methodology was carried out. Two variables viz. temperature (°C) and ethanol concentration (%) with 5 levels (-1.414, -1, 0, +1 and +1.414) were used to design the optimisation model using central composite rotatable design where, -1.414 and +1.414 refer to axial values, -1 and +1 mean factorial points and 0 refers to centre point of the design. The two variables, temperature of 40°C and ethanol concentration of 65% were the optimised conditions for the response variables of total phenolic content, ferric reducing antioxidant capacity and 2,2-diphenyl-1-picrylhydrazyl scavenging activity. The reverse phase-high pressure liquid chromatography chromatogram of the polyphenol extract showed eight phenolic acids and ascorbic acid. The extract was then encapsulated with maltodextrin (⩽ DE 20) by spray and freeze drying methods at three different concentrations. Highest encapsulating efficiency was obtained in freeze dried encapsulates (78-97%). The obtained optimised model could be used for polyphenol extraction from star fruit pomace and microencapsulates can be incorporated in different food systems to enhance their antioxidant property. Copyright © 2014 Elsevier Ltd. All rights reserved.

Undercooled water in basaltic regoliths and implications for fluidized debris flows on Mars

NASA Technical Reports Server (NTRS)

Gooding, James L.

1987-01-01

Pursuant to the past attribution of many geomorphic features on Mars to the movements of water- or ice-lubricated debris, experiments have been conducted for water freezing in wet, sand-like basaltic substrates. It is found that substantial undercooling can be achieved under Martian conditions, independently of freezing-point depressions due to soluble salts. Attention is given to results for a clay-poor soil with negligible salinity from Mauna Kea, Hawaii, which demonstrate that the degree of undercooling is essentially independent of both soil particle size and water/soil mass ratio, albeit with cooling rate variations.

The succinonitrile triple-point standard: a fixed point to improve the accuracy of temperature measurements in the clinical laboratory.

PubMed

Mangum, B W

1983-07-01

In an investigation of the melting and freezing behavior of succinonitrile, the triple-point temperature was determined to be 58.0805 degrees C, with an estimated uncertainty of +/- 0.0015 degrees C relative to the International Practical Temperature Scale of 1968 (IPTS-68). The triple-point temperature of this material is evaluated as a temperature-fixed point, and some clinical laboratory applications of this fixed point are proposed. In conjunction with the gallium and ice points, the availability of succinonitrile permits thermistor thermometers to be calibrated accurately and easily on the IPTS-68.

Seasonal Flows in Palikir Crater

NASA Image and Video Library

2013-05-15

Seasonal flows on warm Martian slopes may be caused by the flow of salty water on Mars, active today when the surface is warm above the freezing point of the solution. This observation is from NASA Mars Reconnaissance Orbiter.

Plant thermal hysteresis proteins.

PubMed

Urrutia, M E; Duman, J G; Knight, C A

1992-05-22

Proteins which produce a thermal hysteresis (i.e. lower the freezing point of water below the melting point) are common antifreezes in cold adapted poikilothermic animals, especially fishes from ice-laden seas and terrestrial arthropods. However, these proteins have not been previously identified in plants. 16 species of plants collected from northern Indiana in autumn and winter had low levels of thermal hysteresis activity, but activity was absent in summer. This suggests that thermal hysteresis proteins may be a fairly common winter adaptation in angiosperms. Winter stem fluid from the bittersweet nightshade, Solanum dulcamara L., also showed the recrystallization inhibition activity characteristic of the animal thermal hysteresis proteins (THPs), suggesting a possible function for the THPs in this freeze tolerant species. Other potential functions are discussed. Antibodies to an insect THP cross reacted on immunoelectroblots with proteins in S. dulcamara stem fluid, indicating common epitopes in the insect and plant THPs.

Pore architecture of nanoporous gold and titania by hydrogen thermoporometry

DOE PAGES

Johnston, L. T.; Biener, M. M.; Ye, J. C.; ...

2015-07-10

Nanoporous gold (NPG) and materials derived from it by templating have complex pore architecture that determines their technologically relevant physical properties. Here, we apply high-resolution hydrogen thermoporometry to study the pore structure of NPG and NPG-derived titania nanofoam (TNF). Results reveal complex multimodal pore size distributions for NPG and TNF. The freezing–melting hysteresis is pronounced, with freezing and melting scans having entirely different shapes. Experiments involving partial freeze–melt cycles reveal the lack of direct correlation between individual freezing and melting peaks, pointing to phenomena that are beyond the Gibbs-Thomson formalism. The depression of the average freezing temperature scales linearly withmore » the ratio of the internal surface area (measured by gas sorption) and the total pore volume derived from the density of monoliths. In conclusion, thermoporometry yields total pore volumes in good agreement with those derived from monolith densities for both NPG and TNF.« less

Non-equilibrium freezing behaviour of aqueous systems.

PubMed

MacKenzie, A P

1977-03-29

The tendencies to non-equilibrium freezing behaviour commonly noted in representative aqueous systems derive from bulk and surface properties according to the circumstances. Supercooling and supersaturation are limited by heterogeneous nucleation in the presence of solid impurities. Homogeneous nucleation has been observed in aqueous systems freed from interfering solids. Once initiated, crystal growth is ofter slowed and, very frequently, terminated with increasing viscosity. Nor does ice first formed always succeed in assuming its most stable crystalline form. Many of the more significant measurements on a given systeatter permitting the simultaneous representation of thermodynamic and non-equilibrium properties. The diagram incorporated equilibrium melting points, heterogeneous nucleation temperatures, homogeneous nucleation temperatures, glass transition and devitrification temperatures, recrystallization temperatures, and, where appropriate, solute solubilities and eutectic temperatures. Taken together, the findings on modle systems aid the identification of the kinetic and thermodynamic factors responsible for the freezing-thawing survival of living cells.

Numerical study of the effect of the shape of the phase diagram on the eutectic freezing temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ode, M.; Shimono, M.; Sasajima, N.

2013-09-11

To evaluate the reliability of metal-carbon eutectic systems as fixed points for the next generation of high-temperature standards the effect of thermodynamic properties related to the shape of eutectic phase diagram on the freezing temperature is investigated within the context of the numerical multi-phase-field model. The partition coefficient and liquidus slopes of the two solids involved in the eutectic reaction are varied deliberately and independently. The difference between the eutectic temperature and the freezing temperature is determined in dependence of the solid/liquid (s/l) interface shape and concentration. Where appropriate reference is made to the Jackson-Hunt analytical theory. It is shownmore » that there are mainly two typical conditions to decrease the undercooling: 1) a small liquidus slope and 2) the associated difference between the eutectic composition and the liquid composition during solidification.« less

Pore architecture of nanoporous gold and titania by hydrogen thermoporometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnston, L. T.; Biener, M. M.; Ye, J. C.

Nanoporous gold (NPG) and materials derived from it by templating have complex pore architecture that determines their technologically relevant physical properties. Here, we apply high-resolution hydrogen thermoporometry to study the pore structure of NPG and NPG-derived titania nanofoam (TNF). Results reveal complex multimodal pore size distributions for NPG and TNF. The freezing–melting hysteresis is pronounced, with freezing and melting scans having entirely different shapes. Experiments involving partial freeze–melt cycles reveal the lack of direct correlation between individual freezing and melting peaks, pointing to phenomena that are beyond the Gibbs-Thomson formalism. The depression of the average freezing temperature scales linearly withmore » the ratio of the internal surface area (measured by gas sorption) and the total pore volume derived from the density of monoliths. In conclusion, thermoporometry yields total pore volumes in good agreement with those derived from monolith densities for both NPG and TNF.« less

Observations on the Freezing of Supercooled Pollen Washing Water by a New Electrodynamic Balance

NASA Astrophysics Data System (ADS)

Tong, Haijie; Pope, Francis D.; Kalberer, Markus

2014-05-01

Primary biological particles can act as efficient ice nuclei (IN) by initiating freezing events at temperatures warmer than the homogenous freezing temperature [1, 2]. For example, pollen grain particles can trigger freezing events at temperatures as warm as -5 °C in the contact freezing mode [3]. More recently pollen residues, which are released by washing pollen grains in water, were also observed to act as efficient IN in the immersion mode [4, 5]. In this study we developed a new cold electrodynamic balance (CEDB) system and investigated the freezing properties of single particles of supercooled pollen washing water (SPWW). The EDB technique allows for a contact free measurement of freezing events. The phase of the particle (liquid or frozen solid) can be distinguished via measuring the Mie scattering signal from the particle. Furthermore the size of liquid (spherical) particles can be determined. The freezing events are characterized through the loss of the regular Mie scattering signal from the levitated droplet as it changes state from liquid to a frozen solid. The statistical freezing probabilities of SPWW were obtained in the temperature range: -15 to -40 °C. Each temperature measurement point consists of the analysis of 30-100 droplets. Preliminary conclusions are that SPWW is IN active in the immersion mode. Further discussion will focus on the temperature range of the IN activity, the important variables (other than temperature) for IN activity, other likely modes of IN activity, and the implications of these results in terms of the atmospheric relevance of SPWW. This study was supported by the NERC. We acknowledge Professor Jonathan Reid and James Davis from the University of Bristol for providing information of the design of the warm EDB system. References: [1] Möhler, O., et al. (2007) Biogeosciences, 4, 1059-1071. [2] Prenni, A. J., et al. (2009) Nat. Geosci., 2, 401-404. [3] Diehl, K., et al. (2002) Atmos. Res., 61, 125-133. [4] Pummer, B. G., et al. (2012) Atmos. Chem. Phys., 12, 2541-2550. [5] Augustin, S., et al. (2013) Atmos. Chem. Phys., 13, 10989-11003.

Investigation of the Behavior of the Co C Eutectic Fixed Point

NASA Astrophysics Data System (ADS)

Girard, F.; Battuello, M.; Florio, M.

2007-12-01

The behavior of the Co C eutectic fixed point was investigated at INRIM. Several cells of different design and volume, and filled with cobalt of different purity were constructed and investigated with both Pt/Pd thermocouples and radiation thermometers. The melting behavior was investigated with respect to the melting rate, the pre-freezing rate, and the annealing time. The melting temperatures, as defined, were not significantly affected by the different testing conditions, even if the shape and duration of the plateaux were influenced. Several tens of melt and freeze cycles were performed with the different cells. The spread in the results for all of the different conditions was very limited in extent, giving rise to a standard deviation of less than 0.04 °C; a repeatability of better than 0.02 °C was found with both Pt/Pd thermocouples and radiation thermometers. The results of our measurements are encouraging and confirm the suitability of Co C as a reference point for the high-temperature range in a possible future temperature scale. Investigations of long-term stability remain ongoing.

Low density microcellular foams

DOEpatents

Aubert, J.H.; Clough, R.L.; Curro, J.G.; Quintana, C.A.; Russick, E.M.; Shaw, M.T.

1985-10-02

Low density, microporous polymer foams are provided by a process which comprises forming a solution of polymer and a suitable solvent followed by rapid cooling of the solution to form a phase-separated system and freeze the phase-separated system. The phase-separated system comprises a polymer phase and a solvent phase, each of which is substantially continuous within the other. The morphology of the polymer phase prior to and subsequent to freezing determine the morphology of the resultant foam. Both isotropic and anisotropic foams can be produced. If isotropic foams are produced, the polymer and solvent are tailored such that the solution spontaneously phase-separates prior to the point at which any component freezes. The morphology of the resultant polymer phase determines the morphology of the reusltant foam and the morphology of the polymer phase is retained by cooling the system at a rate sufficient to freeze one or both components of the system before a change in morphology can occur. Anisotropic foams are produced by forming a solution of polymer and solvent that will not phase separate prior to freezing of one or both components of the solution. In such a process, the solvent typically freezes before phase separation occurs. The morphology of the resultant frozen two-phase system determines the morphology of the resultant foam. The process involves subjecting the solution to essentially one-dimensional cooling. Foams having a density of less than 0.1 g/cc and a uniform cell size of less than 10 ..mu..m and a volume such that the foams have a length greater than 1 cm are provided.

FIMP dark matter freeze-in gauge mediation and hidden sector

NASA Astrophysics Data System (ADS)

Tsao, Kuo-Hsing

2018-07-01

We explore the dark matter freeze-in mechanism within the gauge mediation framework, which involves a hidden feebly interacting massive particle (FIMP) coupling feebly with the messenger fields while the messengers are still in the thermal bath. The FIMP is the fermionic component of the pseudo-moduli in a generic metastable supersymmetry (SUSY) breaking model and resides in the hidden sector. The relic abundance and the mass of the FIMP are determined by the SUSY breaking scale and the feeble coupling. The gravitino, which is the canonical dark matter candidate in the gauge mediation framework, contributes to the dark matter relic abundance along with the freeze-in of the FIMP. The hidden sector thus becomes two-component with both the FIMP and gravitino lodging in the SUSY breaking hidden sector. We point out that the ratio between the FIMP and the gravitino is determined by how SUSY breaking is communicated to the messengers. In particular when the FIMP dominates the hidden sector, the gravitino becomes the minor contributor in the hidden sector. Meanwhile, the neutralino is assumed to be both the weakly interacting massive particle dark matter candidate in the freeze-out mechanism and the lightest observable SUSY particle. We further find out the neutralino has the sub-leading contribution to the current dark matter relic density in the parameter space of our freeze-in gauge mediation model. Our result links the SUSY breaking scale in the gauge mediation framework with the FIMP freeze-in production rate leading to a natural and predicting scenario for the studies of the dark matter in the hidden sector.

Aluminum Fixed Point: Impact of the Time Spent in the Liquid Phase on the Liquid-Solid Transition and Obviousness of the Pollution of the Ingot

NASA Astrophysics Data System (ADS)

Renaot, E.; Martin, C.

2011-08-01

In order to improve the uncertainty on the aluminum fixed point, a study was launched by Laboratoire Commun de Métrologie LNE-CNAM in the frame of the EURAMET Project 732 "Toward more accurate temperature fixed points" (coordinating laboratory: France, 17 partner countries). An earlier study completed in this laboratory showed that in regular realization of the melting-freezing plateaus, there is no diffusion of impurities in the thickness of the ingot, or the diffusion is excessively slow and cannot allow a uniform distribution of the impurities. On the other hand, it is frequently noticed that the experimental conditions before the freezing plateau have an impact on its characteristics (value, slope,…). Up to now, no systematic study was performed on the influence of this parameter. So, the objective of the task started recently in this laboratory is to investigate the influence of the time spent in the liquid phase on the phase transition. As a final result, it is demonstrated that in order to reach the equilibrium of the concentration of impurities, it is necessary to ensure that the metal remains in the liquid phase at least 24 h before initiating the freeze. At the end of the process, the aluminum ingot was chemically analyzed. The analyses reveal large contaminations of the surface of the ingot (sodium, sulfur, and phosphorus). One of the important outputs of this study is that the conditions of usage of the cells should be given important attention since large contaminations can be brought by the furnace.

Potential of Near-Infrared Chemical Imaging as Process Analytical Technology Tool for Continuous Freeze-Drying.

PubMed

Brouckaert, Davinia; De Meyer, Laurens; Vanbillemont, Brecht; Van Bockstal, Pieter-Jan; Lammens, Joris; Mortier, Séverine; Corver, Jos; Vervaet, Chris; Nopens, Ingmar; De Beer, Thomas

2018-04-03

Near-infrared chemical imaging (NIR-CI) is an emerging tool for process monitoring because it combines the chemical selectivity of vibrational spectroscopy with spatial information. Whereas traditional near-infrared spectroscopy is an attractive technique for water content determination and solid-state investigation of lyophilized products, chemical imaging opens up possibilities for assessing the homogeneity of these critical quality attributes (CQAs) throughout the entire product. In this contribution, we aim to evaluate NIR-CI as a process analytical technology (PAT) tool for at-line inspection of continuously freeze-dried pharmaceutical unit doses based on spin freezing. The chemical images of freeze-dried mannitol samples were resolved via multivariate curve resolution, allowing us to visualize the distribution of mannitol solid forms throughout the entire cake. Second, a mannitol-sucrose formulation was lyophilized with variable drying times for inducing changes in water content. Analyzing the corresponding chemical images via principal component analysis, vial-to-vial variations as well as within-vial inhomogeneity in water content could be detected. Furthermore, a partial least-squares regression model was constructed for quantifying the water content in each pixel of the chemical images. It was hence concluded that NIR-CI is inherently a most promising PAT tool for continuously monitoring freeze-dried samples. Although some practicalities are still to be solved, this analytical technique could be applied in-line for CQA evaluation and for detecting the drying end point.

A novel freeze-dried storage and preparation method for the determination of mycophenolic acid in plasma by high-performance liquid chromatography.

PubMed

Wang, Lei; Qiang, Wei; Li, Ying; Cheng, Zeneng; Xie, Mengmeng

2017-09-01

Plasma samples were conventionally stored at freezing conditions until the time of detection. Such a technique, when carried out over an extended period, is energy consuming; in addition, preparation and transportation of stored samples is inconvenient. In this study, a freeze-dried storage and preparation method was proposed to determine the presence of mycophenolic acid (MPA) in plasma. Fresh plasma samples were freeze-dried using a device, and then stored at ambient temperature. After the stored samples were soaked with methanol spiked with the internal standard, high-performance liquid chromatography was conducted to detect MPA. The proposed method was demonstrated to be precise and accurate over the linear range of 0.5-50 μg mL -1 , with both intra- and inter-day precision being <7% and biases <10%. The freeze-dried samples were stable at ambient temperature for at least 40 days. This method was also successfully applied to the pharmacokinetic study of MPA in healthy volunteers. Pharmacokinetic parameters, such as maximum plasma concentration, time point of maximum plasma concentration and elimination half-life, among others, were consistent with the results in the published study. This proposed technique was proved to be simple, reproducible and energy saving. This approach could also simplify the storage and analysis of samples in clinical and scientific drug research. Copyright © 2017 John Wiley & Sons, Ltd.

Strong tolerance to freezing is a major survival strategy in insects inhabiting central Yakutia (Sakha Republic, Russia), the coldest region on earth.

PubMed

Li, N G

2016-10-01

Yakutia is a part of eastern Siberia, located in north-eastern Russia. The climate of this area is very harsh even by Siberian standards, and is characterized by the absolute temperature minimum, which is below -64.4 °C, and a long period of low temperatures reaching to a range between -47 and -55 °C. Despite such a severe climate, the fauna and flora of Yakutia present a considerably rich biodiversity, suggesting a high adaptation potential of the organisms in this area. In this study, 30 local species of insects belonging to Coleoptera, Diptera and Lepidoptera were selected to investigate cold adaptation. The identification of the cold adaptation strategy was based on the measurement of the insect body supercooling point (SCP) and hemolymph ice-nucleating activity. According to the data collected, there is a high incidence of freeze tolerant species among the insects found in Yakutsk area (Yakutsk, 62° latitude, 130° longitude): 93.3% of them were freeze tolerant, and only 6.7% were freeze avoiding. It is suggested that the evolution of cold hardiness in this region preferably develops for the selection of the strong freeze tolerance that allow the insects to survive extreme cold conditions. Copyright © 2016 Elsevier Inc. All rights reserved.

Does Platelet-Rich Plasma Freeze-Thawing Influence Growth Factor Release and Their Effects on Chondrocytes and Synoviocytes?

PubMed Central

Cavallo, Carola; Cenacchi, Annarita; Facchini, Andrea; Grigolo, Brunella; Kon, Elizaveta; Mariani, Erminia; Pratelli, Loredana; Marcacci, Maurilio

2014-01-01

PRP cryopreservation remains a controversial point. Our purpose was to investigate the effect of freezing/thawing on PRP molecule release, and its effects on the metabolism of chondrocytes and synoviocytes. PRP was prepared from 10 volunteers, and a half volume underwent one freezing/thawing cycle. IL-1β, HGF, PDGF AB/BB, TGF-β1, and VEGF were assayed 1 hour and 7 days after activation. Culture media of chondrocytes and synoviocytes were supplemented with fresh or frozen PRP, and, at 7 days, proliferation, gene expression, and secreted proteins levels were evaluated. Results showed that in the freeze-thawed PRP the immediate and delayed molecule releases were similar or slightly lower than those in fresh PRP. TGF-β1 and PDGF AB/BB concentrations were significantly reduced after freezing both at 1 hour and at 7 days, whereas HGF concentration was significantly lower in frozen PRP at 7 days. In fresh PRP IL-1β and HGF concentrations underwent a significant further increase after 7 days. Similar gene expression was found in chondrocytes cultured with both PRPs, whereas in synoviocytes HGF gene expression was higher in frozen PRP. PRP cryopreservation is a safe procedure, which sufficiently preserves PRP quality and its ability to induce proliferation and the production of ECM components in chondrocytes and synoviocytes. PMID:25136613

Bilateral Comparison Between NIM and NMC Over the Temperature Range from 83.8058 K to 692.677 K

NASA Astrophysics Data System (ADS)

Sun, Jianping; Ye, Shaochun; Kho, Haoyuan; Zhang, Jintao; Wang, Li

2015-08-01

A bilateral comparison of local realization of the International Temperature Scale of 1990 between the National Institute of Metrology (NIM) and National Metrology Centre (NMC) was carried out over the temperature range from 83.8058 K to 692.677 K. It involved six fixed points including the argon triple point, the mercury triple point, the triple point of water, the melting point of gallium, the freezing point of tin, and the freezing point of zinc. In 2009, NMC asked NIM to participate in a bilateral comparison to link the NMC results to the Consultative Committee for Thermometry Key Comparison 3 (CCT-K3) and facilitate the NMC's calibration and measurement capabilities submission. This comparison was agreed by NIM and Asia Pacific Metrology Programme in 2009, and registered in the Key Comparison Database in 2010 as CCT-K3.2. NMC supplied two fused silica sheath standard platinum resistance thermometers (SPRTs) as traveling standards. One of them was used at the Ga, Sn, and Zn fixed points, while the other one was used at the Ar and Hg fixed points. NMC measured them before and after NIM measured them. During the comparison, a criterion for the SPRT was set as the stability at the triple point of water to be less than 0.3 mK. The results for both laboratories are summarized. A proposal for linking the NMC's comparison results to CCT-K3 is presented. The difference between NMC and NIM and the difference between NMC and the CCT-K3 average reference value using NIM as a link are reported with expanded uncertainties at each measured fixed point.

Growth and characterization of SrI2:Eu2+ single crystal for gamma ray detector applications

NASA Astrophysics Data System (ADS)

Raja, A.; Daniel, D. Joseph; Ramasamy, P.; Singh, S. G.; Sen, S.; Gadkari, S. C.

2018-04-01

Europium activated Strontium Iodide single crystal was grown by vertical Bridgman-stockbarger technique. The melting point and freezing point of SrI2:Eu2+ crystal was analyzed by TG/DTA. The Radioluminescence emission was recorded. The scintillation measurement was carried out for the grown SrI2:Eu2+ crystal under 137Cs gamma energy source.

Did Water Leave Its Mark on Mars?

ERIC Educational Resources Information Center

Secosky, James J.

1989-01-01

Discusses the missing water on Mars. Describes five experiments simulating conditions on Mars: (1) behavior of dry ice; (2) low-pressure vacuum; (3) freezing point depression; (4) water in hydrated minerals and clay; and (5) properties of carbon dioxide. (YP)

30 CFR 250.1715 - How must I permanently plug a well?

Code of Federal Regulations, 2010 CFR

2010-07-01

... in the intervals. (10) Permafrost areas (i) A fluid to be left in the hole that has a freezing point below the temperature of the permafrost, and a treatment to inhibit corrosion; and(ii) Cement plugs...

Comparative study of subtalar arthrodesis after calcaneal frature malunion with autologous bone graft or freeze-dried xenograft.

PubMed

Henning, Carlo; Poglia, Gabriel; Leie, Murilo Anderson; Galia, Carlos Roberto

2015-12-01

Calcaneal fracture malunion may evolve into arthrosis and severe foot deformities. The aim of this study was to identify differences in bony union following corrective subtalar arthrodesis with interposition of autologous tricortical bone graft or freeze-dried bovine xenograft. We prospectively evaluated 12 patients who underwent subtalar arthrodesis, six patients received autografts and 6 received freeze-dried bovine xenografts. After a mean followup of 58 weeks, the patients were clinical assessed using AOFAS scale and the visual analog scale (VAS) for pain and for final radiographic parameters measurement. Two blind raters evaluated the length of time required for solid union of the arthrodesis and graft integration by retrospective radiographic examination. In the autograft group, AOFAS score improved from a preoperative average of 37 to 64 points postoperatively (p = 0.02) and mean VAS score improved from 4.7 to 1.9 (p = 0.028). In the xenograft group, AOFAS score improved from 38 to 74 points (p = 0.02) and VAS from 5.5 to 2.7 (p = 0.046). Solid union was achieved in all cases in the autograft group at an average of 5.3 weeks and in five cases in the xenograft group at 8.8 weeks (p = 0.077). Graft integration occurred after an average of 10.7 weeks in the autograft group and 28.8 weeks in the xenograft group (p = 0.016). With the numbers available, no significant difference could be detected in the length of time required for solid union of subtalar arthrodesis between groups, although time to integration of freeze-dried bovine xenografts was statistically higher. Clinical and functional improvement was observed in both groups.

NIM Realization of the Gallium Triple Point

NASA Astrophysics Data System (ADS)

Xiaoke, Yan; Ping, Qiu; Yuning, Duan; Yongmei, Qu

2003-09-01

In the last three years (1999 to 2001), the gallium triple-point cell has been successfully developed, and much corresponding research has been carried out at the National Institute of Metrology (NIM), Beijing, China. This paper presents the cell design, apparatus and procedure for realizing the gallium triple point, and presents studies on the different freezing methods. The reproducibility is 0.03 mK, and the expanded uncertainty of realization of the gallium triple point is evaluated to be 0.17 mK (p=0.99, k=2.9). Also, the reproducibility of the gallium triple point was compared with that of the triple point of water.

Impact behaviour of freeze-dried and fresh pomelo (Citrus maxima) peel: influence of the hydration state

PubMed Central

Thielen, Marc; Speck, Thomas; Seidel, Robin

2015-01-01

Pomelos (Citrus maxima) are known for their thick peel which—inter alia—serves as energy dissipator when fruits impact on the ground after being shed. It protects the fruit from splitting open and thus enables the contained seeds to stay germinable and to potentially be dispersed by animal vectors. The main part of the peel consists of a parenchymatous tissue that can be interpreted from a materials point of view as open pored foam whose struts are pressurized and filled with liquid. In order to investigate the influence of the water content on the energy dissipation capacity, drop weight tests were conducted with fresh and with freeze-dried peel samples. Based on the coefficient of restitution it was found that freeze-drying markedly reduces the relative energy dissipation capacity of the peel. Measuring the transmitted force during impact furthermore indicated a transition from a uniform collapse of the foam-like tissue to a progressive collapse due to water extraction. Representing the peel by a Maxwell model illustrates that freeze-drying not only drastically reduces the damping function of the dashpots but also stiffens the springs of the model. PMID:26543566

Freezing point and solid-liquid interfacial free energy of Stockmayer dipolar fluids: a molecular dynamics simulation study.

PubMed

Wang, Jun; Apte, Pankaj A; Morris, James R; Zeng, Xiao Cheng

2013-09-21

Stockmayer fluids are a prototype model system for dipolar fluids. We have computed the freezing temperatures of Stockmayer fluids at zero pressure using three different molecular-dynamics simulation methods, namely, the superheating-undercooling method, the constant-pressure and constant-temperature two-phase coexistence method, and the constant-pressure and constant-enthalpy two-phase coexistence method. The best estimate of the freezing temperature (in reduced unit) for the Stockmayer (SM) fluid with the dimensionless dipole moment μ*=1, √2, √3 is 0.656 ± 0.001, 0.726 ± 0.002, and 0.835 ± 0.005, respectively. The freezing temperature increases with the dipolar strength. Moreover, for the first time, the solid-liquid interfacial free energies γ of the fcc (111), (110), and (100) interfaces are computed using two independent methods, namely, the cleaving-wall method and the interfacial fluctuation method. Both methods predict that the interfacial free energy increases with the dipole moment. Although the interfacial fluctuation method suggests a weaker interfacial anisotropy, particularly for strongly dipolar SM fluids, both methods predicted the same trend of interfacial anisotropy, i.e., γ100 > γ110 > γ111.

Cryopreservative effects of the recombinant ice-binding protein from the arctic yeast Leucosporidium sp. on red blood cells.

PubMed

Lee, Sung Gu; Koh, Hye Yeon; Lee, Jun Hyuck; Kang, Sung-Ho; Kim, Hak Jun

2012-06-01

Antifreeze proteins (AFPs) have important functions in many freeze-tolerant organisms. The proteins non-colligatively lower the freezing point and functionally inhibit ice recrystallization in frozen solutions. In our previous studies, we found that the Arctic yeast Leucosporidium sp. produces an AFP (LeIBP), and that the protein could be successfully produced in Pichia expression system. The present study showed that recombinant LeIBP possesses the ability to reduce the damage induced to red blood cells (RBCs) by freeze thawing. In addition to 40 % glycerol, both 0.4 and 0.8 mg/ml LeIBPs significantly reduced freeze-thaw-induced hemolysis at either rapid- (45 °C) or slow-warming (22 °C) temperatures. Post-thaw cell counts of the cryopreserved RBCs were dramatically enhanced, in particular, in 0.8 mg/ml LeIBP. Interestingly, the cryopreserved cells in the presence of LeIBP showed preserved cell size distribution. These results indicate that the ability of LeIBP to inhibit ice recrystallization helps the RBCs avoid critically damaging electrolyte concentrations, which are known as solution effects. Considering all these data, LeIBP can be thought of as a key component in improving RBC cryopreservation efficiency.

Freeze-dried plasma at the point of injury: from concept to doctrine.

PubMed

Glassberg, Elon; Nadler, Roy; Gendler, Sami; Abramovich, Amir; Spinella, Philip C; Gerhardt, Robert T; Holcomb, John B; Kreiss, Yitshak

2013-12-01

While early plasma transfusion for the treatment of patients with ongoing major hemorrhage is widely accepted as part of the standard of care in the hospital setting, logistic constraints have limited its use in the out-of-hospital setting. Freeze-dried plasma (FDP), which can be stored at ambient temperatures, enables early treatment in the out-of-hospital setting. Point-of-injury plasma transfusion entails several significant advantages over currently used resuscitation fluids, including the avoidance of dilutional coagulopathy, by minimizing the need for crystalloid infusion, beneficial effects on endothelial function, physiological pH level, and better maintenance of intravascular volume compared with crystalloid-based solutions. The Israel Defense Forces Medical Corps policy is that plasma is the resuscitation fluid of choice for selected, severely wounded patients and has thus included FDP as part of its armamentarium for use at the point of injury by advanced life savers, across the entire military. We describe the clinical rationale behind the use of FDP at the point-of-injury, the drafting of the administration protocol now being used by Israel Defense Forces advanced life support providers, the process of procurement and distribution, and preliminary data describing the first casualties treated with FDP at the point of injury. It is our hope that others will be able to learn from our experience, thus improving trauma casualty care around the world.

ALGORITHM TO REDUCE APPROXIMATION ERROR FROM THE COMPLEX-VARIABLE BOUNDARY-ELEMENT METHOD APPLIED TO SOIL FREEZING.

USGS Publications Warehouse

Hromadka, T.V.; Guymon, G.L.

1985-01-01

An algorithm is presented for the numerical solution of the Laplace equation boundary-value problem, which is assumed to apply to soil freezing or thawing. The Laplace equation is numerically approximated by the complex-variable boundary-element method. The algorithm aids in reducing integrated relative error by providing a true measure of modeling error along the solution domain boundary. This measure of error can be used to select locations for adding, removing, or relocating nodal points on the boundary or to provide bounds for the integrated relative error of unknown nodal variable values along the boundary.

Fuel system design concepts for broad property fuels

NASA Technical Reports Server (NTRS)

Versaw, E. F.

1984-01-01

The results of a study assessing the impact of using jet fuel with relaxed specification properties on an aircraft fuel system are given. The study objectives were to identify credible values for specific fuel properties which might be relaxed, to evolve advanced fuel system designs for airframe and engines which would permit use of the specified relaxed properties fuels, and to evaluate performance of the candidate advanced fuel systems and the relaxed property fuels in a typical transport aircraft. The study used, as a baseline, the fuel system incorporated in the Lockheed Tristar. This aircraft is powered by three RB.211-524 Rolls-Royce engines and incorporates a Pratt and Whitney ST6C-421 auxiliary power unit for engine starting and inflight emergency electrical power. The fuel property limits examined are compared with commercial Jet A kerosene and the NASA RFP fuel properties. A screening of these properties established that a higher freezing point and a lower thermal stability would impact fuel system design more significantly than any of the other property changes. Three candidate fuel systems which combine the ability to operate with fuels having both a high freeze point and a low thermal stability are described. All candidates employ bleed air to melt fuel freeze-out prior to starting the APU or an inoperable engine. The effects of incorporating these systems on aircraft weight and engine specific fuel consumption are given.

Water Phase Change Heat Exchanger System Level Analysis for Low Lunar Orbit

NASA Technical Reports Server (NTRS)

Navarro, Moses; Ungar, Eugene; Sheth, Rubik; Hansen, Scott

2016-01-01

In low Lunar orbit (LLO) the thermal environment is cyclic - extremely cold in the eclipse and as warm as room temperature near the subsolar point. Phase change material heat exchangers (PCHXs) are the best option for long term missions in these environments. The Orion spacecraft will use a n-pentadecane wax PCHX for its envisioned mission to LLO. Using water as a PCM material is attractive because its higher heat of fusion and greater density result in a lighter, more compact PCHX. To assess the use of a water PCHX for a human spacecraft in a circular LLO, a system level analysis was performed for the Orion spacecraft. Three cases were evaluated: 1) A one-to-one replacement of the wax PCHX on the internal thermal control loop with a water PCHX (including the appropriate control modifications), 2) reducing the radiator return setpoint temperature below Orion's value to enhance PCHX freezing, and 3) placing the water PCM on the external loop. The model showed that the water PCHX could not be used as a drop-in replacement for the wax PCHX. It did not freeze fully during the eclipse owing to its low freezing point. To obtain equivalent performance, 40% more radiator area than the Orion baseline was required. The study shows that, although water PCHXs are attractive at a component level, system level effects mean that they are not the best choice for LLO.

Multivalent Display of Antifreeze Proteins by Fusion to Self-Assembling Protein Cages Enhances Ice-Binding Activities.

PubMed

Phippen, Sean W; Stevens, Corey A; Vance, Tyler D R; King, Neil P; Baker, David; Davies, Peter L

2016-12-13

Antifreeze proteins (AFPs) are small monomeric proteins that adsorb to the surface of ice to inhibit ice crystal growth and impart freeze resistance to the organisms producing them. Previously, monomeric AFPs have been conjugated to the termini of branched polymers to increase their activity through the simultaneous binding of more than one AFP to ice. Here, we describe a superior approach to increasing AFP activity through oligomerization that eliminates the need for conjugation reactions with varying levels of efficiency. A moderately active AFP from a fish and a hyperactive AFP from an Antarctic bacterium were genetically fused to the C-termini of one component of the 24-subunit protein cage T33-21, resulting in protein nanoparticles that multivalently display exactly 12 AFPs. The resulting nanoparticles exhibited freezing point depression >50-fold greater than that seen with the same concentration of monomeric AFP and a similar increase in the level of ice-recrystallization inhibition. These results support the anchored clathrate mechanism of binding of AFP to ice. The enhanced freezing point depression could be due to the difficulty of overgrowing a larger AFP on the ice surface and the improved ice-recrystallization inhibition to the ability of the nanoparticle to simultaneously bind multiple ice grains. Oligomerization of these proteins using self-assembling protein cages will be useful in a variety of biotechnology and cryobiology applications.

Stable, high-level expression of a type I antifreeze protein in Escherichia coli.

PubMed

Solomon, R G; Appels, R

1999-06-01

The type I antifreeze proteins are simple amphipathic helical proteins found in abundance in polar fish species, where they act to prevent freezing of internal fluids by a mechanism of noncolligative freezing point depression. Large-scale production of these proteins for research and biotechnological purposes has been hampered by their apparent instability when expressed in heterologous host systems. This has necessitated their production as fusion proteins, in polymeric form, or as proproteins for secretion, with the concomitant necessity for postpurification processing to generate the mature form of the protein. We have successfully expressed a recombinant variant of type I antifreeze protein (rAFP) in Escherichia coli using the inducible T7 polymerase transcription expression system. The rAFP contains five copies of the 11 amino acid ice-binding repeat motif found in all type I antifreeze proteins. The protein accumulates to high levels intracellularly in the form of inclusion bodies, with no apparent degradation by the cellular proteolytic machinery. We have devised a simple and rapid purification protocol for this recombinant type I antifreeze protein which does not require cellular fractionation, purification of the inclusion bodies, or chromatographic steps. This protocol may be of general use for this class of protein. The protein displays all three activities common to these proteins: recrystallization inhibition, noncolligative freezing point depression, and modification of the morphology of single ice crystals in solution.

A new approach for freezing of aqueous solutions under active control of the nucleation temperature.

PubMed

Petersen, Ansgar; Schneider, Hendrik; Rau, Guenter; Glasmacher, Birgit

2006-10-01

An experimental setup for controlled freezing of aqueous solutions is introduced. The special feature is a mechanism to actively control the nucleation temperature via electrofreezing: an ice nucleus generated at a platinum electrode by the application of an electric high voltage pulse initiates the crystallization of the sample. Using electrofreezing, the nucleation temperature in pure water can be precisely adjusted to a desired value over the whole temperature range between a maximum temperature Tn(max) close to the melting point and the temperature of spontaneous nucleation. However, the presence of additives can inhibit the nucleus formation. The influence of hydroxyethylstarch (HES), glucose, glycerol, additives commonly used in cryobiology, and NaCl on Tn(max) were investigated. While the decrease showed to be moderate for the non-ionic additives, the hindrance of nucleation by ionic NaCl makes the direct application of electrofreezing in solutions with physiological salt concentrations impossible. Therefore, in the multi-sample freezing device presented in this paper, the ice nucleus is produced in a separate volume of pure water inside an electrode cap. This way, the nucleus formation becomes independent of the sample composition. Using electrofreezing rather than conventional seeding methods allows automated freezing of many samples under equal conditions. Experiments performed with model solutions show the reliability and repeatability of this method to start crystallization in the test samples at different specified temperatures. The setup was designed to freeze samples of small volume for basic investigations in the field of cryopreservation and freeze-drying, but the mode of operation might be interesting for many other applications where a controlled nucleation of aqueous solutions is of importance.

Low density microcellular foams

DOEpatents

Aubert, James H.; Clough, Roger L.; Curro, John G.; Quintana, Carlos A.; Russick, Edward M.; Shaw, Montgomery T.

1987-01-01

Low density, microporous polymer foams are provided by a process which comprises forming a solution of polymer and a suitable solvent followed by rapid cooling of the solution to form a phase-separated system and freeze the phase-separated system. The phase-separated system comprises a polymer phase and a solvent phase, each of which is substantially continuous within the other. The morphology of the polymer phase prior to and subsequent to freezing determine the morphology of the resultant foam. Both isotropic and anisotropic foams can be produced. If isotropic foams are produced, the polymer and solvent are tailored such that the solution spontaneously phase-separates prior to the point at which any component freezes. The morphology of the resultant polymer phase determines the morphology of the resultant foam and the morphology of the polymer phase is retained by cooling the system at a rate sufficient to freeze one or both components of the system before a change in morphology can occur. Anisotropic foams are produced by forming a solution of polymer and solvent that will not phase separate prior to freezing of one or both components of the solution. In such a process, the solvent typically freezes before phase separation occurs. The morphology of the resultant frozen two-phase system determines the morphology of the resultant foam. The process involves subjecting the solution to essentially one-dimensional cooling. Means for subjecting such a solvent to one-dimensional cooling are also provided. Foams having a density of less than 0.1 g/cc and a uniform cell size of less than 10 .mu.m and a volume such that the foams have a length greater than 1 cm are provided.

Elementary Science Notes

ERIC Educational Resources Information Center

School Science Review, 1972

1972-01-01

Short articles describe techniques suitable for junior high school science, including the use of a toy drinking bird" to start discussion, using cobalt chloride solution to demonstrate convection currents, demonstration of the relationship between freezing point and concentration, and instructions for building a simple lens camera, a circuit…

Low temperature fuel behavior studies

NASA Technical Reports Server (NTRS)

Stockemer, F. J.

1980-01-01

Aircraft fuels at low temperatures near the freezing point. The principal objective was an improved understanding of the flowability and pumpability of the fuels in a facility that simulated the heat transfer and temperature profiles encountered during flight in the long range commercial wing tanks.

Solidification and Re-melting Phenomena During Slurry Preparation Using the RheoMetal™ Process

NASA Astrophysics Data System (ADS)

Payandeh, M.; Sabzevar, Mohsen Haddad; Jarfors, A. E. W.; Wessén, M.

2017-12-01

The melting sequence of the enthalpy exchange material (EEM) and formation of a slurry in the RheoMetal™ process was investigated. The EEM was extracted and quenched, together with a portion of the slurry at different processing times before complete melting. The EEM initially increased in size/diameter due to melt freezing onto its surface, forming a freeze- on layer. The initial growth of this layer was followed by a period of a constant diameter of the EEM with subsequent melting and decrease of diameter. Microstructural characterization of the size and morphology of different phases in the EEM and in the freeze-on layer was made. Dendritic equiaxed grains and eutectic regions containing Si particles and Cu-bearing particles and Fe-rich particles were observed in the as-cast EEM. The freeze-on layer consisted of dendritic aluminum tilted by about 30 deg in the upstream direction, caused by the rotation of the EEM. Energy dispersion spectroscopy analysis showed that the freeze-on layer had a composition corresponding to an alloy with higher melting point than the EEM and thus shielding the EEM from the surrounding melt. Microstructural changes in the EEM showed that temperature rapidly increased to 768 K (495 °C), indicated by incipient melting of the lowest temperature melting eutectic in triple junction grain boundary regions with Al2Cu and Al5Mg8Si6Cu2 phases present. As the EEM temperature increased further the binary Al-Si eutectic started to melt to form a region of a fully developed coherent mushy state. Experimental results and a thermal model indicated that as the dendrites spheroidized near to the interface at the EEM/freeze-on layer reached a mushy state with 25 pct solid fraction, coherency was lost and disintegration of the freeze-on layer took place. Subsequently, in the absence of the shielding effect from the freeze-on Layer, the EEM continued to disintegrate with a coherency limit of a solid fraction estimated to be 50 pct.

Transmembrane ion distribution during recovery from freezing in the woolly bear caterpillar Pyrrharctia isabella (Lepidoptera: Arctiidae).

PubMed

Boardman, Leigh; Terblanche, John S; Sinclair, Brent J

2011-08-01

During extracellular freezing, solutes in the haemolymph are concentrated, resulting in osmotic dehydration of the cells, which must be reversed upon thawing. Here, we used freeze tolerant Pyrrharctia isabella (Lepidoptera: Arctiidae) larvae to examine the processes of ion redistribution after thawing. To investigate the effect of the intensity of cold exposure on ion redistribution after thawing, we exposed caterpillars to -14°C, -20°C or -30°C for 35h. To investigate the effect of duration of cold exposure on ion redistribution after thawing, we exposed the caterpillars to -14°C for up to 6 weeks while sampling several time points. The concentrations of Na(+), K(+), Mg(2+) and Ca(2+) were measured after thawing in the haemolymph, fat body, muscle, midgut tissue and hindgut tissue. Being frozen for long durations (>3 weeks) or at low temperatures (-30°C) both result in 100% mortality, although different ions and tissues appear to be affected by each treatment. Both water distribution and ion content changes were detected after thawing, with the largest effects seen in the fat body and midgut tissue. Magnesium homeostasis appears to be vital for post-freeze survival in these larvae. The movement of ions during thawing lagged behind the movement of water, and ion homeostasis was not restored within the same time frame as water homeostasis. Failure to regain ion homeostasis after thawing is therefore implicated in mortality of freeze tolerant insects. Copyright © 2011 Elsevier Ltd. All rights reserved.

Dynamic freeze-in: impact of thermal masses and cosmological phase transitions on dark matter production

NASA Astrophysics Data System (ADS)

Baker, Michael J.; Breitbach, Moritz; Kopp, Joachim; Mittnacht, Lukas

2018-03-01

The cosmological abundance of dark matter can be significantly influenced by the temperature dependence of particle masses and vacuum expectation values. We illustrate this point in three simple freeze-in models. The first one, which we call kinematically induced freeze-in, is based on the observation that the effective mass of a scalar temporarily becomes very small as the scalar potential undergoes a second order phase transition. This opens dark matter production channels that are otherwise forbidden. The second model we consider, dubbed vev-induced freeze-in, is a fermionic Higgs portal scenario. Its scalar sector is augmented compared to the Standard Model by an additional scalar singlet, S, which couples to dark matter and temporarily acquires a vacuum expectation value (a two-step phase transition or "vev flip-flop"). While < S> ≠ 0, the modified coupling structure in the scalar sector implies that dark matter production is significantly enhanced compared to the < S> = 0 phases realised at very early times and again today. The third model, which we call mixing-induced freeze-in, is similar in spirit, but here it is the mixing of dark sector fermions, induced by non-zero < S>, that temporarily boosts the dark matter production rate. For all three scenarios, we carefully dissect the evolution of the dark sector in the early Universe. We compute the DM relic abundance as a function of the model parameters, emphasising the importance of thermal corrections and the proper treatment of phase transitions in the calculation.

The mineralogical consequences and behavior of descending acid-sulfate waters: An example from the Karaha - Telaga Bodas geothermal system, Indonesia

USGS Publications Warehouse

Moore, J.N.; Christenson, B.W.; Allis, R.G.; Browne, P.R.L.; Lutz, S.J.

2004-01-01

Acidic steam condensates in volcanic systems or shallow, oxygenated geothermal environments are typically enriched in SO4 and poor in Cl. These fluids produce distinctive alteration-induced assemblages as they descend. At Karaha - Telaga Bodas, located on the flank of Galunggung Volcano, Indonesia, neutralization of descending acid waters has resulted in the successive appearance of 1) advanced argillic alteration characterized by alunite, clay minerals and pyrite, 2) anhydrite, pyrite and interlayered sheet silicates, and 3) carbonates. Minor tourmaline, fluorite and native sulfur also are present locally, reflecting interactions with discharging magmatic gases. Water rock interactions were modeled at temperatures up to 250??C using the composition of acidic lake water from Telaga Bodas and that of a typical andesite as reactants. The simulations predict mineral distributions consistent with the observed assemblages and a decrease in the freezing-point depression of the fluid with increasing temperature. Fluids trapped in anhydrite, calcite and fluorite display a similar decrease in their freezing-point depressions, from 2.8?? to 1.5??C, as homogenization temperatures increase from 160?? to 205??C. The simulations indicate that the progressive change in fluid composition is due mainly to the incorporation of SO4 into the newly formed hydrothermal minerals. The salinities of fluid inclusions containing Cl-deficient steam condensates are better expressed in terms of H2SO4 equivalents than the commonly used NaCl equivalents. At solute concentrations >1.5 molal, freezing-point depressions represented as NaCl equivalents overestimate the salinity of Cl-poor waters. At lower concentrations, differences between apparent salinities calculated as NaCl and H2SO 4 equivalents are negligible.

Determination of the dew point and the frost point below 0 degrees C making use of the beta-ray backscattering and the electric conductivity on the narrow surface of insulated layer.

PubMed

Matsumoto, S; Kobayashi, H

1979-10-15

It is necessary to distinguish between the dew point and the frost point below 0 degrees C. The freezing of the dew and the melting of the frost are respectively detected by the rapid decrease and the increase of the conduction current on the narrow surface of insulated layer made of epoxy, 0.5 mm in width and 10 mm in length, on which the dew deposits. The dew point -9 degrees C and the frost point -8 degrees C in the humidity 21% at the temperature 13 degrees C are clearly distinguished in this method.

Early Mars was wet but not warm: Erosion, fluvial features, liquid water habitats, and life below freezing

NASA Technical Reports Server (NTRS)

Mckay, C. P.; Davis, W. L.

1993-01-01

There is considerable evidence that Mars had liquid water early in its history and possibly at recurrent interval. It has generally been assumed that this implied that the climate was warmer as a result of a thicker CO2 atmosphere than at the present. However, recent models suggest that Mars may have had a thick atmosphere but may not have experienced mean annual temperatures above freezing. In this paper we report on models of liquid water formation and maintenance under temperatures well below freezing. Our studies are based on work in the north and south polar regions of Earth. Our results suggest that early Mars did have a thick atmosphere but precipitation and hence erosion was rare. Transient liquid water, formed under temperature extremes and maintained under thick ice covers, could account for the observed fluvial features. The main difference between the present climate and the early climate was that the total surface pressure was well above the triple point of water.

Experimental Investigation of Concrete Runway Snow Melting Utilizing Heat Pipe Technology

PubMed Central

Su, Xin; Ye, Qing; Fu, Jianfeng

2018-01-01

A full scale snow melting system with heat pipe technology is built in this work, which avoids the negative effects on concrete structure and environment caused by traditional deicing chemicals. The snow melting, ice-freezing performance and temperature distribution characteristics of heat pipe concrete runway were discussed by the outdoor experiments. The results show that the temperature of the concrete pavement is greatly improved with the heat pipe system. The environment temperature and embedded depth of heat pipe play a dominant role among the decision variables of the snow melting system. Heat pipe snow melting pavement melts the snow completely and avoids freezing at any time when the environment temperature is below freezing point, which is secure enough for planes take-off and landing. Besides, the exportation and recovery of geothermal energy indicate that this system can run for a long time. This paper will be useful for the design and application of the heat pipe used in the runway snow melting. PMID:29551957

Experimental Investigation of Concrete Runway Snow Melting Utilizing Heat Pipe Technology.

PubMed

Chen, Fengchen; Su, Xin; Ye, Qing; Fu, Jianfeng

2018-01-01

A full scale snow melting system with heat pipe technology is built in this work, which avoids the negative effects on concrete structure and environment caused by traditional deicing chemicals. The snow melting, ice-freezing performance and temperature distribution characteristics of heat pipe concrete runway were discussed by the outdoor experiments. The results show that the temperature of the concrete pavement is greatly improved with the heat pipe system. The environment temperature and embedded depth of heat pipe play a dominant role among the decision variables of the snow melting system. Heat pipe snow melting pavement melts the snow completely and avoids freezing at any time when the environment temperature is below freezing point, which is secure enough for planes take-off and landing. Besides, the exportation and recovery of geothermal energy indicate that this system can run for a long time. This paper will be useful for the design and application of the heat pipe used in the runway snow melting.

Is sperm cryopreservation at -150 degree C a feasible alternative?

PubMed

Medrano, A; Cabrera, F; González, F; Batista, M; Gracia, A

2002-01-01

A series of experiments was carried out to validate a -150 degree C ultra-low temperature freezer for its possible use to properly freeze and store semen. In the first part, crude sample handling was simulated to see whether temperature of stored samples was maintained within a safe range; also, the freezing point and latent heat of fusion plateau of a semen extender were monitored. In the second part, buck semen was (i) frozen in liquid nitrogen and stored in the ultra-low freezer, (ii) frozen and stored in the ultra-low freezer, and (iii) frozen and stored in liquid nitrogen, to compare sperm cryosurvival between freezing methods. Both, frequent removal of samples and long opening of the freezer door did not negatively affect stored sample temperature; latent heat of fusion plateau was 5 minutes long. Semen stored either at -150 degree C or at -196 degree C cryosurvived similarly after 2 days and after 2 months of cryopreservation.

Passive ice freezing-releasing heat pipe

DOEpatents

Gorski, Anthony J.; Schertz, William W.

1982-01-01

A heat pipe device has been developed which permits completely passive ice formation and periodic release of ice without requiring the ambient temperature to rise above the melting point of water. This passive design enables the maximum amount of cooling capacity to be stored in the tank.

Construction of Home-Made Tin Fixed-Point Cell at TUBITAK UME

NASA Astrophysics Data System (ADS)

Kalemci, M.; Arifovic, N.; Bağçe, A.; Aytekin, S. O.; Ince, A. T.

2015-08-01

TUBITAK UME Temperature Laboratory initiated a new study which focuses on the construction of a tin freezing-point cell as a primary temperature standard. The design is an open-cell type similar to the National Institute of Standards and Technology design. With this aim, a brand new vacuum and filling line employing an oil diffusion pump and two cold traps (liquid nitrogen and dry ice) was set-up. The graphite parts (crucible, thermometer well, etc.) have been baked at high temperature under vacuum. Each cell was filled with approximately 1 kg of high-purity tin (99.9999 %) in a three-zone furnace. Then several melting and freezing curves were obtained to assess the quality of the home-made cell, and also the new cell was compared with the existing reference cell of the laboratory. The results obtained are very close to the reference cell of UME, indicating that the method used for fabrication was promising and satisfactory and also seems to meet the requirements to have a primary level temperature standard.

Poly(vinyl methyl ether) hydrogels at temperatures below the freezing point of water-molecular interactions and states of water.

PubMed

Pastorczak, Marcin; Dominguez-Espinosa, Gustavo; Okrasa, Lidia; Pyda, Marek; Kozanecki, Marcin; Kadlubowski, Slawomir; Rosiak, Janusz M; Ulanski, Jacek

2014-01-01

Water interacting with a polymer reveals a number of properties very different to bulk water. These interactions lead to the redistribution of hydrogen bonds in water. It results in modification of thermodynamic properties of water and the molecular dynamics of water. That kind of water is particularly well observable at temperatures below the freezing point of water, when the bulk water crystallizes. In this work, we determine the amount of water bound to the polymer and of the so-called pre-melting water in poly(vinyl methyl ether) hydrogels with the use of Raman spectroscopy, dielectric spectroscopy, and calorimetry. This analysis allows us to compare various physical properties of the bulk and the pre-melting water. We also postulate the molecular mechanism responsible for the pre-melting of part of water in poly(vinyl methyl ether) hydrogels. We suggest that above -60 °C, the first segmental motions of the polymer chain are activated, which trigger the process of the pre-melting.

Monitoring temperatures in the vaccine cold chain in Bolivia.

PubMed

Nelson, Carib; Froes, Paulo; Dyck, Anne Mie Van; Chavarría, Jeaneth; Boda, Enrique; Coca, Alberto; Crespo, Gladys; Lima, Heinz

2007-01-05

This study monitored vaccine cold chain temperatures during routine DTP-HB-Hib vaccine shipments from central stores to 11 communities in 3 provinces of Bolivia. In all 11 monitored shipments, vaccines were exposed to freezing temperatures at one or more points. In each of the shipments, temperatures below 0 degrees C were recorded for 2-50% of the monitoring period. Freezing occurred at almost every level of the cold chain distribution system, especially during district and health center storage and during transport to the province and district levels. Seven of the 11 shipments were exposed to temperatures above 8 degrees C, although none were exposed to excessive heat longer than 1.3% of the total monitoring period.

In vitro uses of biological cryoprotectants.

PubMed Central

Lillford, Peter J; Holt, Chris B

2002-01-01

Ice can be anything from a highly destructive agent in agriculture to a useful building material. Established industries are based on the known rules of physics and chemistry which allow some control of amounts of ice or ice crystal geometry. However, organisms have much more subtle requirements to maintain their delicate internal structure if they are to survive freezing. As a result they have selected specific molecules for freezing-point depression, osmotic regulation, ice nucleation and crystal growth inhibition. All these active species may have potential commercial use once they are identified, understood and produced at economic scales. We examine the progress made so far in extending biological subtlety into commercial processes, and look for prospects for further innovation. PMID:12171658

METHOD OF AND APPARATUS FOR WITHDRAWING LIGHT ISOTOPIC PRODUCT FROM A LIQUID THERMAL DIFFUSION PLANT

DOEpatents

Dole, M.

1959-09-22

An improved process and apparatus are described for removing enriched product from the columns of a thermal diffusion plant for separation of isotopes. In the removal cycle, light product at the top cf the diffusion columns is circulated through the column tops and a shipping cylinder connected thereto unttl the concertation of enriched product in the cylinder reaches the desired point. During the removal, circulation through the bottoms is blocked bv freezing. in the diffusion cycle, the bottom portion is unfrozen, fresh feed is distributed to the bottoms of the columns, ard heavy product is withdrawn from the bottoms, while the tops of the columns are blocked by freezing.

Passive ice freezing-releasing heat pipe. [Patent application

DOEpatents

Gorski, A.J.; Schertz, W.W.

1980-09-29

A heat pipe device has been developed which permits completely passive ice formation and periodic release of ice without requiring the ambient temperature to rise above the melting point of water. This passive design enables the maximum amount of cooling capacity to be stored in the tank.

Equilibrium, quasi-equilibrium, and nonequilibrium freezing of mammalian embryos.

PubMed

Mazur, P

1990-08-01

The first successful freezing of early embryos to -196 degrees C in 1972 required that they be cooled slowly at approximately 1 degree C/min to about -70 degrees C. Subsequent observations and physical/chemical analyses indicate that embryos cooled at that rate dehydrate sufficiently to maintain the chemical potential of their intracellular water close to that of the water in the partly frozen extracellular solution. Consequently, such slow freezing is referred to as equilibrium freezing. In 1972 and since, a number of investigators have studied the responses of embryos to departures from equilibrium freezing. When disequilibrium is achieved by the use of higher constant cooling rates to -70 degrees C, the results is usually intracellular ice formation and embryo death. That result is quantitatively in accord with the predictions of the physical/chemical analysis of the kinetics of water loss as a function of cooling rate. However, other procedures involving rapid nonequilibrium cooling do not result in high mortality. One common element in these other nonequilibrium procedures is that, before the temperature has dropped to a level that permits intracellular ice formation, the embryo water content is reduced to the point at which the subsequent rapid nonequilibrium cooling results in either the formation of small innocuous intracellular ice crystals or the conversion of the intracellular solution into a glass. In both cases, high survival requires that subsequent warming be rapid, to prevent recrystallization or devitrification. The physical/chemical analysis developed for initially nondehydrated cells appears generally applicable to these other nonequilibrium procedures as well.

Freeze shoe sampler for the collection of hyporheic zone sediments and porewater.

PubMed

Bianchin, M; Smith, L; Beckie, R

2015-01-01

The Starr and Ingleton (1992) drive point piston sampler (DPPS) design was modified by fitting it with a Murphy and Herkelrath (1996) type sample-freezing drive shoe (SFDS), which uses liquid carbon dioxide as a cryogen. Liquid carbon dioxide was used to freeze sediments in the lower 0.1 m of the core and the drive-point piston sealed the core at the top preserving the reductive-oxidation (redox) sensitive sediments from the atmosphere and maintaining natural stratigraphy. The use of nitrogen gas to provide positive pressure on the gas system blocked the ingress of water which froze on contact with the cryogen thus blocking the gas lines with ice. With this adaptation to the gas system cores could be collected at greater depths beneath the static water level. This tool was used to collect intact saturated sediment cores from the hyporheic zone of the tidally influenced Fraser River in Vancouver, British Columbia, Canada where steep geochemical and microbial gradients develop within the interface between discharging anaerobic groundwater and recharging aerobic river water. In total, 25 cores driven through a 1.5 m sampling interval were collected from the river bed with a mean core recovery of 75%. The ability to deploy this method from a fishing vessel makes the tool more cost effective than traditional marine-based drilling operations which often use barges, tug boats, and drilling rigs. © 2014, National Ground Water Association.

Freezing, melting and structure of ice in a hydrophilic nanopore.

PubMed

Moore, Emily B; de la Llave, Ezequiel; Welke, Kai; Scherlis, Damian A; Molinero, Valeria

2010-04-28

The nucleation, growth, structure and melting of ice in 3 nm diameter hydrophilic nanopores are studied through molecular dynamics simulations with the mW water model. The melting temperature of water in the pore was T(m)(pore) = 223 K, 51 K lower than the melting point of bulk water in the model and in excellent agreement with experimental determinations for 3 nm silica pores. Liquid and ice coexist in equilibrium at the melting point and down to temperatures as low as 180 K. Liquid water is located at the interface of the pore wall, increasing from one monolayer at the freezing temperature, T(f)(pore) = 195 K, to two monolayers a few degrees below T(m)(pore). Crystallization of ice in the pore occurs through homogeneous nucleation. At the freezing temperature, the critical nucleus contains approximately 75 to 100 molecules, with a radius of gyration similar to the radius of the pore. The critical nuclei contain features of both cubic and hexagonal ice, although stacking of hexagonal and cubic layers is not defined until the nuclei reach approximately 150 molecules. The structure of the confined ice is rich in stacking faults, in agreement with the interpretation of X-ray and neutron diffraction experiments. Though the presence of cubic layers is twice as prevalent as hexagonal ones, the crystals should not be considered defective Ic as sequences with more than three adjacent cubic (or hexagonal) layers are extremely rare in the confined ice.

Freeze, Wait, Reanimate: Cryonic Suspension and Science Fiction

ERIC Educational Resources Information Center

Shoffstall, Grant

2010-01-01

This essay takes as its chief point of departure Jacques Ellul's contention that imaginative treatments of malevolent technology in antitechnological science fiction, by way of inviting rejection, refusal, dismissal, or condemnation, conspire in facilitating human acceptance of and adjustment to technology as it otherwise presently is. The author…

Freeze-dried Plasma at the Point of Injury: from Concept to Doctrine

DTIC Science & Technology

2013-01-01

tranexamic acid , which was em- bedded in the IDF clinical practice guideline for all advanced life support (ALS) medical personnel by mid-2011. The...ficiency virus and hepatitis C virus infections among United States blood donors since the introduction of nucleic acid testing. Transfusion 50(7

Thin, Conductive Permafrost Surrounding Lake Fryxell Indicates Salts From Past Lakes, McMurdo Dry Valleys, Antarctica

NASA Astrophysics Data System (ADS)

Foley, N.; Tulaczyk, S. M.; Gooseff, M. N.; Myers, K. F.; Doran, P. T.; Auken, E.; Dugan, H. A.; Mikucki, J.; Virginia, R. A.

2017-12-01

In the McMurdo Dry Valleys (MDV), permafrost should be thick and liquid water rare. However, despite the well below zero mean annual temperature in this cryospheric desert, liquid water can be found in lakes, summer melt streams, subglacial outflow, and - recent work has shown - underneath anomalously thin permafrost. In part, this niche hydrosphere is maintained by the presence of salts, which depress the freezing point of water to perhaps as cold as -10° Celsius. We detected widespread salty water across the MDV in lakes and at depth using a helicopter-borne Time Domain Electromagnetic (TDEM) sensor. By using the presence of brines to mark the transition from frozen permafrost (near the surface) to unfrozen ground (at depth), we have created a map of permafrost thickness in Lower Taylor Valley (LTV), a large MDV with a complex history of glaciation and occupation by lakes. Our results show that permafrost is thinner ( 200m) than would be expected based on geothermal gradient measurements (up to 1000m), a result of the freezing point depression caused by salt and potentially enhanced by an unfinished transient freezing process. Near Lake Fryxell, a large, brackish lake in the center of LTV, permafrost is very thin (about 30-40m) and notably more electrically conductive than more distal permafrost. This thin ring of conductive permafrost surrounding the lake basin most likely reflects the high presence of salts in the subsurface, preventing complete freezing. These salts may be a remnant of the salty bottom waters of a historic larger lake (LGM glacially dammed Lake Washburn) or the remnant of salty basal water from a past advance of Taylor Glacier, which now sits many km up-valley but is known to contain brines which currently flow onto the surface and directly into the subsurface aquifer.

Classification of jet fuel properties by near-infrared spectroscopy using fuzzy rule-building expert systems and support vector machines.

PubMed

Xu, Zhanfeng; Bunker, Christopher E; Harrington, Peter de B

2010-11-01

Monitoring the changes of jet fuel physical properties is important because fuel used in high-performance aircraft must meet rigorous specifications. Near-infrared (NIR) spectroscopy is a fast method to characterize fuels. Because of the complexity of NIR spectral data, chemometric techniques are used to extract relevant information from spectral data to accurately classify physical properties of complex fuel samples. In this work, discrimination of fuel types and classification of flash point, freezing point, boiling point (10%, v/v), boiling point (50%, v/v), and boiling point (90%, v/v) of jet fuels (JP-5, JP-8, Jet A, and Jet A1) were investigated. Each physical property was divided into three classes, low, medium, and high ranges, using two evaluations with different class boundary definitions. The class boundaries function as the threshold to alarm when the fuel properties change. Optimal partial least squares discriminant analysis (oPLS-DA), fuzzy rule-building expert system (FuRES), and support vector machines (SVM) were used to build the calibration models between the NIR spectra and classes of physical property of jet fuels. OPLS-DA, FuRES, and SVM were compared with respect to prediction accuracy. The validation of the calibration model was conducted by applying bootstrap Latin partition (BLP), which gives a measure of precision. Prediction accuracy of 97 ± 2% of the flash point, 94 ± 2% of freezing point, 99 ± 1% of the boiling point (10%, v/v), 98 ± 2% of the boiling point (50%, v/v), and 96 ± 1% of the boiling point (90%, v/v) were obtained by FuRES in one boundaries definition. Both FuRES and SVM obtained statistically better prediction accuracy over those obtained by oPLS-DA. The results indicate that combined with chemometric classifiers NIR spectroscopy could be a fast method to monitor the changes of jet fuel physical properties.

New particle dependant parameterizations of heterogeneous freezing processes.

NASA Astrophysics Data System (ADS)

Diehl, Karoline; Mitra, Subir K.

2014-05-01

For detailed investigations of cloud microphysical processes an adiabatic air parcel model with entrainment is used. It represents a spectral bin model which explicitly solves the microphysical equations. The initiation of the ice phase is parameterized and describes the effects of different types of ice nuclei (mineral dust, soot, biological particles) in immersion, contact, and deposition modes. As part of the research group INUIT (Ice Nuclei research UnIT), existing parameterizations have been modified for the present studies and new parameterizations have been developed mainly on the basis of the outcome of INUIT experiments. Deposition freezing in the model is dependant on the presence of dry particles and on ice supersaturation. The description of contact freezing combines the collision kernel of dry particles with the fraction of frozen drops as function of temperature and particle size. A new parameterization of immersion freezing has been coupled to the mass of insoluble particles contained in the drops using measured numbers of ice active sites per unit mass. Sensitivity studies have been performed with a convective temperature and dew point profile and with two dry aerosol particle number size distributions. Single and coupled freezing processes are studied with different types of ice nuclei (e.g., bacteria, illite, kaolinite, feldspar). The strength of convection is varied so that the simulated cloud reaches different levels of temperature. As a parameter to evaluate the results the ice water fraction is selected which is defined as the relation of the ice water content to the total water content. Ice water fractions between 0.1 and 0.9 represent mixed-phase clouds, larger than 0.9 ice clouds. The results indicate the sensitive parameters for the formation of mixed-phase and ice clouds are: 1. broad particle number size distribution with high number of small particles, 2. temperatures below -25°C, 3. specific mineral dust particles as ice nuclei such as illite or montmorillonite. Coupled cases of deposition and contact freezing show that they are hardly in competition because of differences in the preferred particle sizes. In the contact mode, small particles are less efficient for collisions as well as less efficient as ice nuclei so that these are available for deposition freezing. On the other hand, immersion freezing is the dominant process when it is coupled with deposition freezing. As it is initiated earlier the formed ice particles consume water vapor for growing. The competition of combined contact and immersion freezing leads to lower ice water contents because more ice particles are formed via the immersion mode. In general, ice clouds and mixed-phase clouds with high ice water fractions are not directly the result of primary ice formation but of secondary ice formation and growth of ice particles at the expense of liquid drops.

Identification of a dynamic temperature threshold for soil moisture freeze/thaw (F/T) state classification using soil real dielectric constant derivatives.

NASA Astrophysics Data System (ADS)

Pardo, R.; Berg, A. A.; Warland, J. S.

2017-12-01

The use of microwave remote sensing for surface ground ice detection has been well documented using both active and passive systems. Typical validation of these remotely sensed F/T state products relies on in-situ air or soil temperature measurements and a threshold of 0°C to identify frozen soil. However, in soil pores, the effects of capillary and adsorptive forces combine with the presence of dissolved salts to depress the freezing point. This is further confounded by the fact that water over this temperature range releases/absorbs latent heat of freezing/fusion. Indeed, recent results from SLAPEx2015, a campaign conducted to evaluate the ability to detect F/T state and examine the controls on F/T detection at multiple resolutions, suggest that using a soil temperature of 0°C as a threshold for freezing may not be appropriate. Coaxial impedance sensors, like Steven's HydraProbeII (HP), are the most widely used soil sensor in water supply forecast and climatological networks. These soil moisture probes have recently been used to validate remote sensing F/T products. This kind of validation is still relatively uncommon and dependent on categorical techniques based on seasonal reference states of frozen and non-frozen soil conditions. An experiment was conducted to identify the correlation between the phase state of the soil moisture and the probe measurements. Eight soil cores were subjected to F/T transitions in an environmental chamber. For each core, at a depth of 2.5 cm, the temperature and real dielectric constant (rdc) were measured every five minutes using HPs while two heat pulse probes captured the apparent heat capacity 24 minutes apart. Preliminary results show the phase transition of water is bounded by inflection points in the soil temperature, attributed to latent heat. The rdc, however, appears to be highly sensitive to changes in the water preceding the phase change. This opens the possibility of estimating a dynamic temperature threshold for soil F/T by identifying the soil temperatures at the times during which these inflection points in the soil rdc occur. This technique provides a more accurate threshold for F/T product than the static reference temperature currently established.

Scavenging of ammonia by raindrops in Saturn's great storm clouds

NASA Astrophysics Data System (ADS)

Delitsky, M. L.; Baines, Kevin

2016-10-01

Observations of the great Saturn storms of 2010-2011 by Cassini instruments showed a very large depletion in atmospheric ammonia. While dynamics will play a role, the very high solubility of ammonia in water may be another important contributor to ammonia depletion in storms. Ammonia exists in Earth's atmosphere and rainstorms dissolve ammonia to a great degree, leaving almost no NH3 in the atmosphere. Studies by Elperin et al (2011, 2013) show that scavenging of ammonia is greatest as a rainstorm starts and lessens as raindrops fall, tapering off to almost zero by the time the rain reaches the ground (Elperin et al 2009). Ammonia is reaching saturation as it dissolves in the aqueous solution. As concentration increases, NH3 is then converted to aqueous species (NH3)x.(H2O)y (Max and Chapados 2013).Ammonia has the highest solubility in water compared to all other gases in the Saturn atmosphere. The Henry's Law constant for NH3 in water is 60 M/atm at 25 C. For H2S, it is 0.001 M/atm. In Saturn storms, it is "raining UP": As water-laden storm clouds convectively rise, ammonia gas will be scavenged and go into solution to a great degree, whilst all the other gases remain mostly in the gas phase. Aqueous ammonia acts as an antifreeze: if ammonia is dissolved in water cloud droplets to the limit of its solubility, as water droplets rise, they can stay liquid (and continue to scavenge NH3) to well below their normal freezing point of 0 Celsius (273 K). The freezing point for a 30 wt % water-ammonia solution is ~189 K. The pressure level where T = 189 K is at 2.8 bars. The normal freezing point of water occurs at the 9 bar pressure level in Saturn's atmosphere. 2.8 bars occurs at the -51 km altitude (below the 1 bar level). 9 bars is at the -130 km level: a difference of 79 km. A water droplet containing 30 wt% NH3 can move upwards from 9 bars to 2.8 bars (79 km) and still remain liquid, only freezing above that altitude. Calculations by the E-AIM model show that ammonia becomes the dominant species as the water droplets rise and cool. Ammonia will be effectively depleted as it is scavenged into water droplets in Saturn's storms.

Use of refinery computer model to predict fuel production

NASA Technical Reports Server (NTRS)

Flores, F. J.

1979-01-01

Several factors (crudes, refinery operation and specifications) that affect yields and properties of broad specification jet fuel were parameterized using the refinery simulation model which can simulate different types of refineries were used to make the calculations. Results obtained from the program are used to correlate yield as a function of final boiling point, hydrogen content and freezing point for jet fuels produced in two refinery configurations, each one processing a different crude mix. Refinery performances are also compared in terms of energy consumption.

Assessment of different sample preparation routes for mass spectrometric monitoring and imaging of lipids in bone cells via ToF-SIMS

PubMed Central

Schaepe, Kaija; Kokesch-Himmelreich, Julia; Rohnke, Marcus; Wagner, Alena-Svenja; Schaaf, Thimo; Wenisch, Sabine; Janek, Jürgen

2015-01-01

In ToF-SIMS analysis, the experimental outcome from cell experiments is to a great extent influenced by the sample preparation routine. In order to better judge this critical influence in the case of lipid analysis, a detailed comparison of different sample preparation routines is performed—aiming at an optimized preparation routine for systematic lipid imaging of cell cultures. For this purpose, human mesenchymal stem cells were analyzed: (a) as chemically fixed, (b) freeze-dried, and (c) frozen-hydrated. For chemical fixation, different fixatives, i.e., glutaraldehyde, paraformaldehyde, and a mixture of both, were tested with different postfixative handling procedures like storage in phosphate buffered saline, water or critical point drying. Furthermore, secondary lipid fixation via osmium tetroxide was taken into account and the effect of an ascending alcohol series with and without this secondary lipid fixation was evaluated. Concerning freeze-drying, three different postprocessing possibilities were examined. One can be considered as a pure cryofixation technique while the other two routes were based on chemical fixation. Cryofixation methods known from literature, i.e., freeze-fracturing and simple frozen-hydrated preparation, were also evaluated to complete the comparison of sample preparation techniques. Subsequent data evaluation of SIMS spectra in both, positive and negative, ion mode was performed via principal component analysis by use of peak sets representative for lipids. For freeze-fracturing, these experiments revealed poor reproducibility making this preparation route unsuitable for systematic investigations and statistic data evaluation. Freeze-drying after cryofixation showed improved reproducibility and well preserved lipid contents while the other freeze-drying procedures showed drawbacks in one of these criteria. In comparison, chemical fixation techniques via glutar- and/or paraformaldehyde proved most suitable in terms of reproducibility and preserved lipid contents, while alcohol and osmium treatment led to the extraction of lipids and are therefore not recommended. PMID:25791294

Assessment of different sample preparation routes for mass spectrometric monitoring and imaging of lipids in bone cells via ToF-SIMS.

PubMed

Schaepe, Kaija; Kokesch-Himmelreich, Julia; Rohnke, Marcus; Wagner, Alena-Svenja; Schaaf, Thimo; Wenisch, Sabine; Janek, Jürgen

2015-03-19

In ToF-SIMS analysis, the experimental outcome from cell experiments is to a great extent influenced by the sample preparation routine. In order to better judge this critical influence in the case of lipid analysis, a detailed comparison of different sample preparation routines is performed-aiming at an optimized preparation routine for systematic lipid imaging of cell cultures. For this purpose, human mesenchymal stem cells were analyzed: (a) as chemically fixed, (b) freeze-dried, and (c) frozen-hydrated. For chemical fixation, different fixatives, i.e., glutaraldehyde, paraformaldehyde, and a mixture of both, were tested with different postfixative handling procedures like storage in phosphate buffered saline, water or critical point drying. Furthermore, secondary lipid fixation via osmium tetroxide was taken into account and the effect of an ascending alcohol series with and without this secondary lipid fixation was evaluated. Concerning freeze-drying, three different postprocessing possibilities were examined. One can be considered as a pure cryofixation technique while the other two routes were based on chemical fixation. Cryofixation methods known from literature, i.e., freeze-fracturing and simple frozen-hydrated preparation, were also evaluated to complete the comparison of sample preparation techniques. Subsequent data evaluation of SIMS spectra in both, positive and negative, ion mode was performed via principal component analysis by use of peak sets representative for lipids. For freeze-fracturing, these experiments revealed poor reproducibility making this preparation route unsuitable for systematic investigations and statistic data evaluation. Freeze-drying after cryofixation showed improved reproducibility and well preserved lipid contents while the other freeze-drying procedures showed drawbacks in one of these criteria. In comparison, chemical fixation techniques via glutar- and/or paraformaldehyde proved most suitable in terms of reproducibility and preserved lipid contents, while alcohol and osmium treatment led to the extraction of lipids and are therefore not recommended.

Satellite microwave observations of a storm complex: A comparative analysis

NASA Technical Reports Server (NTRS)

Martin, D. W.

1985-01-01

The hypothesis that cold events correspond to a particular stage in a class of thunderstorms was tested. That class is a storms class which updrafts are: (1) strong, broad and moist, and (2) extend well above the freezing level. Condition (1) implies strong mesoscale forcing. Condition (2) implies a tall updraft or a relatively low freezing level. Such storms should have big, intense radar echoes and cold, fast-growing anvils. The thunderstorm events were analyzed by radar, rain gauge and GOES infrared observations. Radar was the starting point for detection and definition of the hypothesized thunderstorms. The radar signature is compared to the signature of the storm in rain gauge observations, satellite infrared images and satellite microwave images.

Freeze frame analysis on high speed cinematography of Nd/YAG laser explosions in ocular tissues.

PubMed

Vernon, S A; Cheng, H

1986-05-01

High speed colour cinematography at 400 frames per second was used to photograph both single and train burst Nd/YAG laser applications in ox eyes at threshold energy levels. Measurements of the extent and speed of particle scatter and tissue distortion from the acoustic transient were made from a sequential freeze frame analysis of the films. Particles were observed to travel over 8 mm from the site of Nd/YAG application 20 milliseconds after a single pulse at initial speeds in excess of 20 km/h. The use of train bursts of pulses was seen to increase the number of particles scattered and project the wavefront of particles further from the point of laser application.

Freeze frame analysis on high speed cinematography of Nd/YAG laser explosions in ocular tissues.

PubMed Central

Vernon, S A; Cheng, H

1986-01-01

High speed colour cinematography at 400 frames per second was used to photograph both single and train burst Nd/YAG laser applications in ox eyes at threshold energy levels. Measurements of the extent and speed of particle scatter and tissue distortion from the acoustic transient were made from a sequential freeze frame analysis of the films. Particles were observed to travel over 8 mm from the site of Nd/YAG application 20 milliseconds after a single pulse at initial speeds in excess of 20 km/h. The use of train bursts of pulses was seen to increase the number of particles scattered and project the wavefront of particles further from the point of laser application. Images PMID:3754458

Testing of an Ammonia EVA Vent Tool for the International Space Station

NASA Technical Reports Server (NTRS)

Ungar, Eugene K.; Stanewich, Brett J.; Wilhelm, Sheri Munekata

2000-01-01

When components of the International Space Station ammonia External Active Thermal Control System are replaced on-orbit, they must be vented immediately after removal from the system. Venting ensures that the component is not hard packed with liquid and thus does not pose a hazard. An extravehicular activity (EVA) vent tool has been developed to perform this function. However, there were concerns that the tool could whip, posing a hazard to the EVA astronaut, or would freeze. The ammonia vent tool was recently tested in a thermal/vacuum chamber to demonstrate that it would operate safely and would not freeze during venting. During the test, ammonia mimicking the venting conditions for six different heat exchanger initial conditions was passed through representative test articles. In the present work, the model that was used to develop the ammonia state and flow for the test points is discussed and the test setup and operation is described. The qualitative whipping and freezing results of the test are discussed and vent plume pressure measurements are described and interpreted.

The tolerance of the field slug Deroceras reticulatum to freezing temperatures.

PubMed

Cook, R T

2004-01-01

Cold hardiness of ectotherms has been widely studied in arthropods, but there is a more limited literature on the survival of molluscs at low temperatures. A number of intertidal species have been examined in detail, but terrestrial molluscs have largely been overlooked until recently. This paper reports results of laboratory experiments to evaluate the cold hardiness of the terrestrial slug, Deroceras reticulatum. The mean supercooling point (SCP) rose from -4.2 degree C in summer to -3.6 degree C in winter. The SCP that caused 50 percent mortality (LSCP50) remained constant at -4.7 to -4.8 degree C in both seasons, but slugs were able to survive the frozen state for longer in winter (LD50 of 31.8 minutes compared with 17.0 minutes in summer). Slug survival at freezing temperatures was prolonged to at least five hours when placed on a moist, absorbent substrate. D. reticulatum exhibits partial freeze tolerance, with an increased survival in winter. The results are discussed in relation to the natural environment of slugs.

Ice nucleation triggered by negative pressure.

PubMed

Marcolli, Claudia

2017-11-30

Homogeneous ice nucleation needs supercooling of more than 35 K to become effective. When pressure is applied to water, the melting and the freezing points both decrease. Conversely, melting and freezing temperatures increase under negative pressure, i.e. when water is stretched. This study presents an extrapolation of homogeneous ice nucleation temperatures from positive to negative pressures as a basis for further exploration of ice nucleation under negative pressure. It predicts that increasing negative pressure at temperatures below about 262 K eventually results in homogeneous ice nucleation while at warmer temperature homogeneous cavitation, i. e. bubble nucleation, dominates. Negative pressure occurs locally and briefly when water is stretched due to mechanical shock, sonic waves, or fragmentation. The occurrence of such transient negative pressure should suffice to trigger homogeneous ice nucleation at large supercooling in the absence of ice-nucleating surfaces. In addition, negative pressure can act together with ice-inducing surfaces to enhance their intrinsic ice nucleation efficiency. Dynamic ice nucleation can be used to improve properties and uniformity of frozen products by applying ultrasonic fields and might also be relevant for the freezing of large drops in rainclouds.

Final report on COOMET.T-S1. Comparison of type S thermocouples at the freezing points of zinc, aluminium and copper 2014—2015

NASA Astrophysics Data System (ADS)

Pokhodun, A. I.; Ivanova, A. G.; Duysebayeva, K. K.; Ivanova, K. P.

2015-01-01

Regional comparison of type S thermocouples at the freezing points of zinc, aluminium and copper was initiated by COOMET TC1.1-10 (the technical committee of COOMET `Thermometry and thermal physics'). Three NMI take part in COOMET regional comparison: D I Mendeleev Institute for Metrology (VNIIM) (Russian Federation), National Scientific Centre (Institute of Metrology) (NSC IM, Ukraine), Republic State Enterprise (Kazakhstan Institute of Metrology) (KazInMetr, Republic of Kazakhstan). VNIIM (Russia) was chosen as the coordinator-pilot of the regional comparison. A star type comparison was used. The participants: KazInMetr and NSC IM constructed the type S thermocouples and calibrated them in three fixed points: zinc, aluminum and copper points, using methods of ITS-90 fixed point realizations. The thermocouples have been sent to VNIIM together with the results of the calibration at three fixed points, with the values of the inhomogeneity at temperature 200 °C and the uncertainty evaluations of the results. For calibration of thermocouples the same VNIIM fixed points cells were used. Participating laboratories repeated the calibration of thermocouples after its returning in zinc, aluminum and copper points to determine the stability of its results. In result of the comparison was to evaluate the equivalence of the type S thermocouples calibration in fixed points by NMIs to confirm corresponding lines of international website for NMI's Calibration and Measurement Capabilities (CMC). This paper is the final report of the comparison including analysis of the uncertainty of measurement results. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT WG-KC, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

The physics of ice cream

NASA Astrophysics Data System (ADS)

Clarke, Chris

2003-05-01

Almost everybody likes ice cream, so it can provide an excellent vehicle for discussing and demonstrating a variety of physical phenomena, such as Newton's law of cooling, Boyle's law and the relationship between microstructure and macroscopic properties (e.g. Young's modulus). Furthermore, a demonstration of freezing point depression can be used to make ice cream in the classroom!

VHF Electrical Properties of Frozen Ground Near Point Barrow, Alaska,

DTIC Science & Technology

1981-06-01

depth. When temperature is depressed even further, the freez - 3. RFI does not require the ground to be disturbed ing of any remaining adsorbed water will...sky wave Seattle, Washington, at 18.6 kHz. Both instruments propagating from a distant or local transmitter to use a small ferrite -loaded coil to

14 CFR 125.141 - Engine breather lines.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Engine breather lines. 125.141 Section 125... Requirements § 125.141 Engine breather lines. (a) Engine breather lines must be so arranged that condensed water vapor that may freeze and obstruct the line cannot accumulate at any point. (b) Engine breathers...

14 CFR 125.141 - Engine breather lines.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Engine breather lines. 125.141 Section 125... Requirements § 125.141 Engine breather lines. (a) Engine breather lines must be so arranged that condensed water vapor that may freeze and obstruct the line cannot accumulate at any point. (b) Engine breathers...

14 CFR 125.141 - Engine breather lines.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Engine breather lines. 125.141 Section 125... Requirements § 125.141 Engine breather lines. (a) Engine breather lines must be so arranged that condensed water vapor that may freeze and obstruct the line cannot accumulate at any point. (b) Engine breathers...

14 CFR 125.141 - Engine breather lines.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Engine breather lines. 125.141 Section 125... Requirements § 125.141 Engine breather lines. (a) Engine breather lines must be so arranged that condensed water vapor that may freeze and obstruct the line cannot accumulate at any point. (b) Engine breathers...

Evaluation of the application of some gas chromatographic methods for the determination of properties of synthetic fuels

NASA Technical Reports Server (NTRS)

Antoine, A. C.

1979-01-01

The purpose of the investigation was to evaluate the applicability, to some synthetic fuels, of some gas chromatographic methods now under development for use with petroleum based fuels. Thirty-two jet and diesel fuel samples which were prepared from oil shale and coal syncrudes were examined. The boiling range distribution of each was determined by gas chromatography, and from that data distillation properties were calculated. The calculated results gave sufficient agreement with the measured values that the equations could be useable in their present form. Bulk fuel properties were calculated for the sixteen JP-5 and Diesel No. 2 type fuels. The results show that the equations would not give useable results. Capillary column gas chromatography was used to determine the n-alkane content of the eight JP-5 type samples and the results related to the observed freezing points. The results show that the concentrations of the long straight chain molecules in the fuels exert influence on the freezing point but are not the complete controlling factor.

Evaluation of the application of some gas chromatographic methods for the determination of properties of synthetic fuels

NASA Technical Reports Server (NTRS)

Antoine, A. C.

1978-01-01

The purpose of the investigation was to evaluate the applicability, to some synthetic fuels, of some gas chromatographic methods now under development for use with petroleum based fuels. Thirty-two jet and diesel fuel samples which were prepared from oil shale and coal syncrudes were examined. The boiling range distribution of each was determined by gas chromatography, and from that data distillation properties were calculated. The calculated results gave sufficient agreement with the measured values that the equations could be useable in their present form. Bulk fuel properties were calculated for the 16 JP-5 and Diesel No. 2 type fuels. The results show that the equations would not give useable results. Capillary column gas chromatography was used to determine the n-alkane content of the eight JP-5 type samples and the results related to the observed freezing points. The results show that the concentrations of the long straight chain molecules in the fuels exert influence on the freezing point but are not the complete controlling factor.

Concentration Dependent Speciation and Mass Transport Properties of Switchable Polarity Solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aaron D. Wilson; Christopher J. Orme

2014-12-01

Tertiary amine switchable polarity solvents (SPS) consisting of predominantly water, tertiary amine, and tertiary ammonium and bicarbonate ions were produced at various concentrations for three different amines: N,N-dimethylcyclohexylamine, N,N-dimethyloctylamine, and 1 cyclohexylpiperidine. For all concentrations, physical properties were measured including viscosity, molecular diffusion coefficients, freezing point depression, and density. Based on these measurements a variation on the Mark Houwink equation was developed to predict the viscosity of any tertiary amine SPS as a function of concentration using the amine’s molecular mass. The observed physical properties allowed the identification of solution state speciation of non-osmotic SPS, where the amine to carbonicmore » acid ratio is significantly greater than one. These results indicate that at most concentrations the stoichiometric excess amine is involved in solvating a proton with two amines. The physical properties of osmotic SPS have consistent concentration dependence behavior over a wide range of concentrations; this consistence suggests osmotic pressures based on low concentrations freezing point studies can be reliably extrapolated to higher concentrations.« less

Investigation of Loop Heat Pipe Survival and Restart After Extreme Cold Environment Exposure

NASA Technical Reports Server (NTRS)

Golliher, Eric; Ku, Jentung; Licari, Anthony; Sanzi, James

2010-01-01

NASA plans human exploration near the South Pole of the Moon, and other locations where the environment is extremely cold. This paper reports on the heat transfer performance of a loop heat pipe (LHP) exposed to extreme cold under the simulated reduced gravitational environment of the Moon. A common method of spacecraft thermal control is to use a LHP with ammonia working fluid. Typically, a small amount of heat is provided either by electrical heaters or by environmental design, such that the LHP condenser temperature never drops below the freezing point of ammonia. The concern is that a liquid-filled, frozen condenser would not restart, or that a thawing condenser would damage the tubing due to the expansion of ammonia upon thawing. This paper reports the results of an experimental investigation of a novel approach to avoid these problems. The LHP compensation chamber (CC) is conditioned such that all the ammonia liquid is removed from the condenser and the LHP is nonoperating. The condenser temperature is then reduced to below that of the ammonia freezing point. The LHP is then successfully restarted.

Serum osmolality and effects of water deprivation in captive Asian elephants (Elephas maximus).

PubMed

Hall, Natalie H; Isaza, Ramiro; Hall, James S; Wiedner, Ellen; Conrad, Bettina L; Wamsley, Heather L

2012-07-01

Serum from 21 healthy, captive Asian elephants (Elephas maximus) was evaluated by measured and calculated osmolality. Serum osmolality results for this population of Asian elephants had a median of 261 mOsm/kg and an interquartile interval of 258-269 mOsm/kg when measured by freezing point osmometry and a median of 264 mOsm/kg and an interquartile interval of 257-269 mOsm/kg when measured by vapor pressure osmometry. These values are significantly lower than values reported in other mammalian species and have important diagnostic and therapeutic implications. Calculated osmolality produced unreliable results and needs further study to determine an appropriate formula and its clinical application in this species. A 16-hr water deprivation test in 16 Asian elephants induced a small, subclinical, but statistically significant increase in measured serum osmolality. Serum osmolality, blood urea nitrogen, and total protein by refractometer were sensitive indicators of hydration status. Serum osmolality measurement by freezing point or vapor pressure osmometry is a useful adjunct to routine clinical tests in the diagnostic evaluation of elephants.

Seasonal Flows in the Central Mountains of Hale Crater

NASA Image and Video Library

2015-04-08

Recurring slope lineae are active flows on warm Martian slopes that might be caused by seeping water. One of the most active sites known is in the central peaks of Hale Crater as seen by NASA Mars Reconnaissance Orbiter. This image shows RSL extending downhill from bedrock cliffs, mostly towards the northwest (upper left). This image was acquired in middle summer when RSL are most active in the southern mid latitudes. The RSL in Hale have an unusually "reddish" color compared to most RSL, perhaps due to oxidized iron compounds, like rust. Since HiRISE color is shifted to infra-red wavelengths, they are actually especially bright the near-infrared just beyond the range of human vision. The Hale RSL are also unusual because they began activity much earlier than most RSL sites in the middle southern latitudes, and were well-developed in the early spring (see ESP_038073_1440). If seeping water causes RSL in Hale crater, it must be rich in salts to lower its freezing point significantly below the freezing point of pure water. http://photojournal.jpl.nasa.gov/catalog/PIA19359

Serum osmolality and effects of water deprivation in captive Asian elephants (Elephas maximus)

PubMed Central

Hall, Natalie H.; Isaza, Ramiro; Hall, James S.; Wiedner, Ellen; Conrad, Bettina L.; Wamsley, Heather L.

2013-01-01

Serum from 21 healthy, captive Asian elephants (Elephas maximus) was evaluated by measured and calculated osmolality. Serum osmolality results for this population of Asian elephants had a median of 261 mOsm/kg and an interquartile interval of 258–269 mOsm/kg when measured by freezing point osmometry and a median of 264 mOsm/kg and an interquartile interval of 257–269 mOsm/kg when measured by vapor pressure osmometry. These values are significantly lower than values reported in other mammalian species and have important diagnostic and therapeutic implications. Calculated osmolality produced unreliable results and needs further study to determine an appropriate formula and its clinical application in this species. A 16-hr water deprivation test in 16 Asian elephants induced a small, subclinical, but statistically significant increase in measured serum osmolality. Serum osmolality, blood urea nitrogen, and total protein by refractometer were sensitive indicators of hydration status. Serum osmolality measurement by freezing point or vapor pressure osmometry is a useful adjunct to routine clinical tests in the diagnostic evaluation of elephants. PMID:22643341

Purification, composition, and physical properties of a thermal hysteresis "antifreeze" protein from larvae of the beetle, Tenebrio molitor.

PubMed

Tomchaney, A P; Morris, J P; Kang, S H; Duman, J G

1982-02-16

Proteins which produce a thermal hysteresis (difference between the freezing and melting points) in aqueous solution are well-known for their antifreeze activity in polar marine fishes. Much less is known about the biology and biochemistry of similar antifreeze proteins found in certain insects. A thermal hysteresis protein was purified from cold acclimated larvae of the beetle, Tenebrio molitor, by using ethanol fractionation, DEAE ion-exchange chromatography, gel filtration, and high-pressure liquid chromatography. The purified protein had a molecular mass of 17 000 daltons and its N terminus was lysine. The amino acid composition of the antifreeze protein contained more hydrophilic amino acids than the fish antifreezes. This is consistent with the compositions of previously purified insect thermal hysteresis proteins. However, the percentage of hydrophilic amino acids in this Tenebrio antifreeze protein was considerably less than that of other insect thermal hysteresis proteins. The freezing point depressing activity of the Tenebrio antifreeze was less than that of fish proteins and glycoproteins at low protein concentrations but was greater at high protein concentrations.

Superheating of ice crystals in antifreeze protein solutions

PubMed Central

Celik, Yeliz; Graham, Laurie A.; Mok, Yee-Foong; Bar, Maya; Davies, Peter L.; Braslavsky, Ido

2010-01-01

It has been argued that for antifreeze proteins (AFPs) to stop ice crystal growth, they must irreversibly bind to the ice surface. Surface-adsorbed AFPs should also prevent ice from melting, but to date this has been demonstrated only in a qualitative manner. Here we present the first quantitative measurements of superheating of ice in AFP solutions. Superheated ice crystals were stable for hours above their equilibrium melting point, and the maximum superheating obtained was 0.44 °C. When melting commenced in this superheated regime, rapid melting of the crystals from a point on the surface was observed. This increase in melting temperature was more appreciable for hyperactive AFPs compared to the AFPs with moderate antifreeze activity. For each of the AFP solutions that exhibited superheating, the enhancement of the melting temperature was far smaller than the depression of the freezing temperature. The present findings clearly show that AFPs adsorb to ice surfaces as part of their mechanism of action, and this absorption leads to protection of ice against melting as well as freezing. PMID:20215465

Enhanced expression of Rubisco activase splicing variants differentially affects Rubisco activity during low temperature treatment in Lolium perenne.

PubMed

Jurczyk, Barbara; Pociecha, Ewa; Grzesiak, Maciej; Kalita, Katarzyna; Rapacz, Marcin

2016-07-01

Alternative splicing of the Rubisco activase gene was shown to be a point for optimization of photosynthetic carbon assimilation. It can be expected to be a stress-regulated event that depends on plant freezing tolerance. The aim of the study was to examine the relationships among Rubisco activity, the expression of two Rubisco activase splicing variants and photoacclimation to low temperature. The experiment was performed on two Lolium perenne genotypes with contrasting levels of freezing tolerance. The study investigated the effect of pre-hardening (15°C) and cold acclimation (4°C) on net photosynthesis, photosystem II photochemical activity, Rubisco activity and the expression of two splicing variants of the Rubisco activase gene. The results showed an induction of Rubisco activity at both 15°C and 4°C only in a highly freezing-tolerant genotype. The enhanced Rubisco activity after pre-hardening corresponded to increased expression of the splicing variant representing the large isoform, while the increase in Rubisco activity during cold acclimation was due to the activation of both transcript variants. These boosts in Rubisco activity also corresponded to an activation of non-photochemical mechanism of photoacclimation induced at low temperature exclusively in the highly freezing-tolerant genotype. In conclusion, enhanced expression of Rubisco activase splicing variants caused an increase in Rubisco activity during pre-hardening and cold acclimation in the more freezing-tolerant Lolium perenne genotype. The induction of the transcript variant representing the large isoform may be an important element of increasing the carbon assimilation rate supporting the photochemical mechanism of photosynthetic acclimation to cold. Copyright © 2016 Elsevier GmbH. All rights reserved.

Crystallization of soft matter under confinement at interfaces and in wedges

NASA Astrophysics Data System (ADS)

Archer, Andrew J.; Malijevský, Alexandr

2016-06-01

The surface freezing and surface melting transitions that are exhibited by a model two-dimensional soft matter system are studied. The behaviour when confined within a wedge is also considered. The system consists of particles interacting via a soft purely repulsive pair potential. Density functional theory (DFT) is used to calculate density profiles and thermodynamic quantities. The external potential due to the confining walls is modelled via a hard wall with an additional repulsive Yukawa potential. The surface phase behaviour depends on the range and strength of this repulsion: when the repulsion is weak, the wall promotes freezing at the surface of the wall. The thickness of this frozen layer grows logarithmically as the bulk liquid-solid phase coexistence is approached. Our mean-field DFT predicts that this crystalline layer at the wall must be nucleated (i.e. there is a free energy barrier) and its formation is necessarily a first-order transition, referred to as ‘prefreezing’, by analogy with the prewetting transition. However, in contrast to the latter, prefreezing cannot terminate in a critical point, since the phase transition involves a change in symmetry. If the wall-fluid interaction is sufficiently long ranged and the repulsion is strong enough, surface melting can occur instead. Then the interface between the wall and the bulk crystalline solid is wetted by the liquid phase as the chemical potential is decreased towards the value at liquid-solid coexistence. It is observed that the finite thickness fluid film at the wall has a broken translational symmetry due to its proximity to the bulk crystal, and so the nucleation of the wetting film can be either first order or continuous. Our mean-field theory predicts that for certain wall potentials there is a premelting critical point analogous to the surface critical point for the prewetting transition. When the fluid is confined within a linear wedge, this can strongly promote freezing when the opening angle of the wedge is commensurate with the crystal lattice.

Fundamentals of freeze-drying.

PubMed

Nail, Steven L; Jiang, Shan; Chongprasert, Suchart; Knopp, Shawn A

2002-01-01

Given the increasing importance of reducing development time for new pharmaceutical products, formulation and process development scientists must continually look for ways to "work smarter, not harder." Within the product development arena, this means reducing the amount of trial and error empiricism in arriving at a formulation and identification of processing conditions which will result in a quality final dosage form. Characterization of the freezing behavior of the intended formulation is necessary for developing processing conditions which will result in the shortest drying time while maintaining all critical quality attributes of the freeze-dried product. Analysis of frozen systems was discussed in detail, particularly with respect to the glass transition as the physical event underlying collapse during freeze-drying, eutectic mixture formation, and crystallization events upon warming of frozen systems. Experiments to determine how freezing and freeze-drying behavior is affected by changes in the composition of the formulation are often useful in establishing the "robustness" of a formulation. It is not uncommon for seemingly subtle changes in composition of the formulation, such as a change in formulation pH, buffer salt, drug concentration, or an additional excipient, to result in striking differences in freezing and freeze-drying behavior. With regard to selecting a formulation, it is wise to keep the formulation as simple as possible. If a buffer is needed, a minimum concentration should be used. The same principle applies to added salts: If used at all, the concentration should be kept to a minimum. For many proteins a combination of an amorphous excipient, such as a disaccharide, and a crystallizing excipient, such as glycine, will result in a suitable combination of chemical stability and physical stability of the freeze-dried solid. Concepts of heat and mass transfer are valuable in rational design of processing conditions. Heat transfer by conduction--the dominant mechanism of heat transfer in freeze-drying--is inefficient at the pressures used in freeze-drying. Steps should be taken to improve the thermal contact between the product and the shelf of the freeze dryer, such as eliminating metal trays from the drying process. Quantitation of the heat transfer coefficient for the geometry used is a useful way of assessing the impact of changes in the system such as elimination of product trays and changes in the vial. Because heat transfer by conduction through the vapor increases with increasing pressure, the commonly held point of view that "the lower the pressure, the better" is not true with respect to process efficiency. The optimum pressure for a given product is a function of the temperature at which freeze-drying is carried out, and lower pressures are needed at low product temperatures. The controlling resistance to mass transfer is almost always the resistance of the partially dried solids above the submination interface. This resistance can be minimized by avoiding fill volumes of more than about half the volume of the container. The development scientist should also recognize that very high concentrations of solute may not be appropriate for optimum freeze-drying, particularly if the resistance of the dried product layer increases sharply with concentration. Although the last 10 years has seen the publication of a significant body of literature of great value in allowing development scientists and engineers to "work smarter," there is still much work needed in both the science and the technology of freeze-drying. Scientific development is needed for improving analytical methodology for characterization of frozen systems and freeze-dried solids. A better understanding of the relationship between molecular mobility and reactivity is needed to allow accurate prediction of product stability at the intended storage temperature based on accelerated stability at higher temperatures. This requires that the temperature dependence of glass transition-associated mobility, particularly at temperatures below the glass transition, be studied in greater depth. The relevance of the concept of strong and fragile glasses to frozen systems and freeze-dried solids has only begun to be explored. The list of pharmaceutically acceptable protective solutes is very short, and more imagination--and work--is needed in order to develop pharmaceutically acceptable alternative stabilizers. There is a need for technology development in process monitoring, particularly in developing a way to measure the status of the product during freezing and freeze-drying without placing temperature measurement probes in individual vials of product. The current practice of placing thermocouples in vials is uncertain with respect to reliability of the data, inconsistent with elimination of personnel in close proximity to open vials of product in an aseptic environment, and incompatible with technology for automatic material handling in freeze-drying. In addition, a method for controlling the degree of supercooling during freezing would allow better control of freezing rate and would, in many cases, result in more consistent product quality.

Antifreeze protein-induced superheating of ice inside Antarctic notothenioid fishes inhibits melting during summer warming

PubMed Central

Cziko, Paul A.; DeVries, Arthur L.; Evans, Clive W.; Cheng, Chi-Hing Christina

2014-01-01

Antifreeze proteins (AFPs) of polar marine teleost fishes are widely recognized as an evolutionary innovation of vast adaptive value in that, by adsorbing to and inhibiting the growth of internalized environmental ice crystals, they prevent death by inoculative freezing. Paradoxically, systemic accumulation of AFP-stabilized ice could also be lethal. Whether or how fishes eliminate internal ice is unknown. To investigate if ice inside high-latitude Antarctic notothenioid fishes could melt seasonally, we measured its melting point and obtained a decadal temperature record from a shallow benthic fish habitat in McMurdo Sound, Antarctica. We found that AFP-stabilized ice resists melting at temperatures above the expected equilibrium freezing/melting point (eqFMP), both in vitro and in vivo. Superheated ice was directly observed in notothenioid serum samples and in solutions of purified AFPs, and ice was found to persist inside live fishes at temperatures more than 1 °C above their eqFMP for at least 24 h, and at a lower temperature for at least several days. Field experiments confirmed that superheated ice occurs naturally inside wild fishes. Over the long-term record (1999–2012), seawater temperature surpassed the fish eqFMP in most summers, but never exceeded the highest temperature at which ice persisted inside experimental fishes. Thus, because of the effects of AFP-induced melting inhibition, summer warming may not reliably eliminate internal ice. Our results expose a potentially antagonistic pleiotropic effect of AFPs: beneficial freezing avoidance is accompanied by melting inhibition that may contribute to lifelong accumulation of detrimental internal ice crystals. PMID:25246548

Cold tolerance of the Australian spur-throated locust, Austracris guttulosa.

PubMed

Woodman, James D

2012-03-01

The cold tolerance of overwintering adult Spur-throated locusts, Austracris guttulosa, was examined using measures of supercooling point relative to gender, environmental acclimation and feeding state as well as mortality for a range of sub-zero temperature exposure treatments. Freezing was lethal and supercooling points ranged from -6 to -12.8°C, but were statistically independent of fresh mass, body water content, acclimation, and/or gut content in fed and starved individuals. A significant interaction effect of gender and feeding status showed that the larger bodied females had decreased supercooling capacity with increased food material in the digestive tract. Post-freezing dissections revealed differences in the amount of freshly consumed and retained food material in the digestive tract between fed and starved individuals of each gender, which could explain this effect based on inoculation of ice crystallisation by food particles. Above supercooling temperatures, neither gender nor the rate of cooling had a significant effect on mortality. When cooled from 25°C at 0.1 or 0.5°Cmin(-1) to a range of experimental minimum temperatures held for 3h, survival was ~74% to -7°C, but declined sharply to ~37% when cooled to -8°C or lower. Although the laboratory experiments reported here suggest that A. guttulosa is not freeze tolerant and unable to rapidly cold harden, exposure to typical cold and frosty nights that very rarely reach below -8°C as a night minimum in the field would be unlikely to cause mortality in the vast majority of overwintering aggregations. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Antifreeze protein-induced superheating of ice inside Antarctic notothenioid fishes inhibits melting during summer warming.

PubMed

Cziko, Paul A; DeVries, Arthur L; Evans, Clive W; Cheng, Chi-Hing Christina

2014-10-07

Antifreeze proteins (AFPs) of polar marine teleost fishes are widely recognized as an evolutionary innovation of vast adaptive value in that, by adsorbing to and inhibiting the growth of internalized environmental ice crystals, they prevent death by inoculative freezing. Paradoxically, systemic accumulation of AFP-stabilized ice could also be lethal. Whether or how fishes eliminate internal ice is unknown. To investigate if ice inside high-latitude Antarctic notothenioid fishes could melt seasonally, we measured its melting point and obtained a decadal temperature record from a shallow benthic fish habitat in McMurdo Sound, Antarctica. We found that AFP-stabilized ice resists melting at temperatures above the expected equilibrium freezing/melting point (eqFMP), both in vitro and in vivo. Superheated ice was directly observed in notothenioid serum samples and in solutions of purified AFPs, and ice was found to persist inside live fishes at temperatures more than 1 °C above their eqFMP for at least 24 h, and at a lower temperature for at least several days. Field experiments confirmed that superheated ice occurs naturally inside wild fishes. Over the long-term record (1999-2012), seawater temperature surpassed the fish eqFMP in most summers, but never exceeded the highest temperature at which ice persisted inside experimental fishes. Thus, because of the effects of AFP-induced melting inhibition, summer warming may not reliably eliminate internal ice. Our results expose a potentially antagonistic pleiotropic effect of AFPs: beneficial freezing avoidance is accompanied by melting inhibition that may contribute to lifelong accumulation of detrimental internal ice crystals.

Report to the CCT on COOMET comparison COOMET.T-K3.1 (previously COOMET.T-S1): Key regional comparison of the national standards of temperature in the range from the triple point of water to the freezing point of zinc

NASA Astrophysics Data System (ADS)

Pokhodun, A. I.

2010-01-01

In the framework of the CIPM MRA, a first COOMET comparison "Comparison of the ITS-90 realizations in the range from 0.01 °C to 429.7485 °C (from the triple point of water to the freezing point of zinc)", registered in the KCDB under the identifier "COOMET.T-K3", was carried out in 2005-2007. Four national metrology institutes took part in this comparison: VNIIM (Russian Federation), SMU (Slovakia), BelGIM (Republic of Belarus) and NSC IM (Ukraine), and two of them (VNIIM and SMU) ensured the linkage with key comparisons CCT-K3 and CCT-K4, in order to disseminate the metrological equivalence to the measurement standards of NSC IM and BelGIM. NSC IM, however, had to withdraw its results, and at the meeting of Technical Committee T-10 of COOMET it was decided to carry out a supplementary bilateral comparison between VNIIM and the NSC IM for realization of the ITS-90 in the same range of temperature. This was registered in the KCDB under the identifier COOMET.T-S1 and measurements were performed in 2008-2009. From the results presented in this report, it is possible to draw the conclusion that the COOMET supplementary comparison COOMET.T-S1 demonstrates the CMC uncertainties claimed by the NSC IM for the melting point of gallium 0.236 mK (k = 2), and the freezing points of indium 1.040 mK (k = 2), tin 0.858 mK (k = 2) and zinc 0.944 mK (k = 2). In September 2012 the Working Group on key Comparisons (WG 7) of the CCT upgraded this comparison to a COOMET key comparison of the 'CCT-K3' type. It is now identified as COOMET.T-K3.1. In April 2013 this report was superseded by item 03006 in the Technical Supplement of 2013. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Monte Carlo Study of Melting of a Model Bulk Ice.

NASA Astrophysics Data System (ADS)

Han, Kyu-Kwang

The methods of NVT (constant number, volume and temperature) and NPT (constant number, pressure and temperature) Monte Carlo computer simulations are used to examine the melting of a periodic hexagonal ice (ice Ih) sample with a unit cell of 192 (rigid) water molecules interacting via the revised central force potentials of Stillinger and Rahman (RSL2). In NVT Monte Carlo simulation of P-T plot for a constant density (0.904g/cm^3) is used to locate onset of the liquid-solid coexistence region (where the slope of the pressure changes sign) and estimate the (constant density) melting point. The slope reversal is a natural consequence of the constant density condition for substances which expand upon freezing and it is pointed out that this analysis is extremely useful for substances such as water. In this study, a sign reversal of the pressure slope is observed near 280 K, indicating that the RSL2 potentials reproduce the freezing expansion expected for water and support a bulk ice Ih system which melts <280 K. The internal energy, specific heat, and two dimensional structure factors for the constant density H_2O system are also examined at a range of temperatures between 100 and 370 K and support the P-T analysis for location of the melting point. This P-T analysis might likewise be useful for determining a (constant density) freezing point, or, with multiple simulations at appropriate densities, the triple point. For NPT Monte Carlo simulations preliminary results are presented. In this study the density, enthalpy, specific heat, and structure factor dependences on temperature are monitored during a sequential heating of the system from 100 to 370 K at a constant pressure (1 atm.). A jump in density upon melting is observed and indicates that the RSL2 potentials reproduce the melting contraction of ice. From the dependences of monitored physical properties on temperature an upper bound on the melting temperature is estimated. In this study we made the first analysis and calculation of the P-T curve for ice Ih melting at constant volume and the first NPT study of ice and of ice melting. In the NVT simulation we found for rho = 0.904g/cm^3 T_ {rm m} ~eq 280 K which is much closer to physical T_ {rm m} than any other published NVT simulation of ice. Finally it is shown that RSL2 potentials do a credible job of describing the thermodynamic properties of ice Ih near its melting point.

Applications of Headspace Moisture Analysis for Investigating the Water Dynamics within a Sealed Vial Containing Freeze-dried Material.

PubMed

Cook, Isobel Ann; Ward, Kevin Richard

2011-01-01

We compare frequency modulation spectroscopy (FMS) as a method of headspace water analysis with the method of Karl Fischer coulometric titration (KF), which is widely used in the analysis of residual water in a freeze-dried material. Parameters relating to the type of formulation (amorphous, crystalline) and the freeze-drying cycle (temperature, pressure, time) were investigated in relation to the resulting headspace moisture (HSM) and total water. We describe the effect of stopper treatment and storage conditions on the HSM levels observed using FMS as a non-destructive method, which also allowed individual vials to be reanalyzed at a series of time points as part of a long-term monitoring exercise. The results of this study enabled a better understanding of the effect of stopper type and pre-lyophilization treatment on the HSM levels both immediately after freeze-drying and upon subsequent storage of the sealed vials of lyophilized material at different temperatures. A clear, linear relationship was observed between HSM and KF values for vials containing freeze-dried sucrose, implying a relatively straightforward interaction between water and the lyophilized cake for this material. Moisture mapping of all vials on one shelf of the freeze-dryer enabled further information to be obtained on the relationship of the formulation, vial, process conditions, equipment geometry, and performance on the intra-batch variability in HSM level and dynamics. It is believed that this could therefore represent a potentially useful technique for quality assurance and in the validation of lyophilization cycles, equipment, and scale-up. Lyophilization, also known as "freeze-drying," is a relatively old technique that has been used in its most basic form for thousands of years (e.g., preservation of fish and meat products). In its more advanced form it is used to preserve many medical products, for example, many vaccines are not stable in solution and therefore need to be dried to allow long-term storage. In order to produce a freeze-dried vaccine a complex understanding of the processes and critical temperatures is required. Once these have been understood the material is dried to give relatively low moisture content (e.g., 2% w/w). This low moisture content is critical for the long-term stability of the product, allowing doctors/chemists to store these goods on site for use when required. This research paper provides further information on a technique called frequency modulation spectroscopy (FMS) that could be used to further our knowledge of the water dynamics within a freeze-dried product, enabling us to increase our understanding of the role various materials and processing conditions play; this in turn could assist in improving quality assurance and ultimately the final product that reaches the consumer.

Thermodynamics of freezing and melting

PubMed Central

Pedersen, Ulf R.; Costigliola, Lorenzo; Bailey, Nicholas P.; Schrøder, Thomas B.; Dyre, Jeppe C.

2016-01-01

Although the freezing of liquids and melting of crystals are fundamental for many areas of the sciences, even simple properties like the temperature–pressure relation along the melting line cannot be predicted today. Here we present a theory in which properties of the coexisting crystal and liquid phases at a single thermodynamic state point provide the basis for calculating the pressure, density and entropy of fusion as functions of temperature along the melting line, as well as the variation along this line of the reduced crystalline vibrational mean-square displacement (the Lindemann ratio), and the liquid's diffusion constant and viscosity. The framework developed, which applies for the sizable class of systems characterized by hidden scale invariance, is validated by computer simulations of the standard 12-6 Lennard-Jones system. PMID:27530064

PREDICTING TWO-DIMENSIONAL STEADY-STATE SOIL FREEZING FRONTS USING THE CVBEM.

USGS Publications Warehouse

Hromadka, T.V.

1986-01-01

The complex variable boundary element method (CVBEM) is used instead of a real variable boundary element method due to the available modeling error evaluation techniques developed. The modeling accuracy is evaluated by the model-user in the determination of an approximative boundary upon which the CVBEM provides an exact solution. Although inhomogeneity (and anisotropy) can be included in the CVBEM model, the resulting fully populated matrix system quickly becomes large. Therefore in this paper, the domain is assumed homogeneous and isotropic except for differences in frozen and thawed conduction parameters on either side of the freezing front. The example problems presented were obtained by use of a popular 64K microcomputer (the current version of the program used in this study has the capacity to accommodate 30 nodal points).

Report on NIM-NMC bilateral comparison: SPRT calibration comparison from -190°C to 420°C

NASA Astrophysics Data System (ADS)

Sun, Jianping; Ye, Shaochun; Wang, Li; Zhang, Jintao; Kho, Haoyuan

2016-01-01

A bilateral comparison of local realization of the International temperature scale of 1990 (ITS-90) between National Institute of Metrology (NIM) and National Metrology Centre (NMC) was carried out over the temperature range from -190°C to 420°C. It involved six fixed points including the argon triple point, the mercury triple point, the triple point of water, the melting point of gallium, the freezing point of tin and the freezing point of zinc. In 2009, NMC asked NIM to participate in a bilateral comparison to link the NMC results to the Consultative Committee for Thermometry Key comparison 3 (CCT-K3) and facilitate the NMC's Calibration and measurement capabilities (CMCs) submission. This comparison was agreed by NIM and Asia Pacific Metrology Programme (APMP) in 2009, and registered in the Key Comparison Database (KCDB) in 2010 as CCT-K3.2. NMC supplied two 25 Ω fused silica sheath standard platinum resistance thermometers (SPRTs) as traveling standards. One of them was used at the Ga, Sn and Zn fixed points, while the other one was used at the Ar and Hg fixed point. NMC measured them before and after NIM measurement. During the comparison, a criterion for the SPRT was set as the stability at the triple point of water to be less than 0.3 mK. The results for both laboratories are summarized. A proposal for linking the NMC's comparison results to CCT-K3 is presented. The difference between NMC and NIM and the difference between NMC and the CCT-K3 Average Reference Value (ARV) using NIM as a link are reported with expanded uncertainties at each measured fixed point. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Standard Materials. A Descriptive List with Prices.

DTIC Science & Technology

1962-03-12

steels (spec- 3.2.4. Freezing-point standards ------- 9 troscopic standards) ---------------- 24 3.2.5. Thermometric standards ------- 9 Ingot irons...metallo-organic materials soluble in lubri- the material is intended) wvith every other sample eating oils, thermometric cells, magnesium-treated...6.00 43g Zinc --------------------------------- 419.50 C ----------------------------- 350 6.00 3.2.5. Thermometric Cells These cells are primarily

7 CFR 3201.37 - General purpose de-icers.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) that are designed to aid in the removal of snow and/or ice, and/or in the prevention of the buildup of snow and/or ice, in general use applications by lowering the freezing point of water. Specialized de-icer products, such as those used to de-ice aircraft and airport runways, are not included. (b) Minimum...

7 CFR 3201.37 - General purpose de-icers.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) that are designed to aid in the removal of snow and/or ice, and/or in the prevention of the buildup of snow and/or ice, in general use applications by lowering the freezing point of water. Specialized de-icer products, such as those used to de-ice aircraft and airport runways, are not included. (b) Minimum...

7 CFR 3201.37 - General purpose de-icers.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) that are designed to aid in the removal of snow and/or ice, and/or in the prevention of the buildup of snow and/or ice, in general use applications by lowering the freezing point of water. Specialized de-icer products, such as those used to de-ice aircraft and airport runways, are not included. (b) Minimum...

7 CFR 2902.37 - General purpose de-icers.

Code of Federal Regulations, 2011 CFR

2011-01-01

... are designed to aid in the removal of snow and/or ice, and/or in the prevention of the buildup of snow and/or ice, in general use applications by lowering the freezing point of water. Specialized de-icer products, such as those used to de-ice aircraft and airport runways, are not included. (b) Minimum biobased...

7 CFR 2902.37 - General purpose de-icers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... are designed to aid in the removal of snow and/or ice, and/or in the prevention of the buildup of snow and/or ice, in general use applications by lowering the freezing point of water. Specialized de-icer products, such as those used to de-ice aircraft and airport runways, are not included. (b) Minimum biobased...

Optimization of a pharmaceutical freeze-dried product and its process using an experimental design approach and innovative process analyzers.

PubMed

De Beer, T R M; Wiggenhorn, M; Hawe, A; Kasper, J C; Almeida, A; Quinten, T; Friess, W; Winter, G; Vervaet, C; Remon, J P

2011-02-15

The aim of the present study was to examine the possibilities/advantages of using recently introduced in-line spectroscopic process analyzers (Raman, NIR and plasma emission spectroscopy), within well-designed experiments, for the optimization of a pharmaceutical formulation and its freeze-drying process. The formulation under investigation was a mannitol (crystalline bulking agent)-sucrose (lyo- and cryoprotector) excipient system. The effects of two formulation variables (mannitol/sucrose ratio and amount of NaCl) and three process variables (freezing rate, annealing temperature and secondary drying temperature) upon several critical process and product responses (onset and duration of ice crystallization, onset and duration of mannitol crystallization, duration of primary drying, residual moisture content and amount of mannitol hemi-hydrate in end product) were examined using a design of experiments (DOE) methodology. A 2-level fractional factorial design (2(5-1)=16 experiments+3 center points=19 experiments) was employed. All experiments were monitored in-line using Raman, NIR and plasma emission spectroscopy, which supply continuous process and product information during freeze-drying. Off-line X-ray powder diffraction analysis and Karl-Fisher titration were performed to determine the morphology and residual moisture content of the end product, respectively. In first instance, the results showed that - besides the previous described findings in De Beer et al., Anal. Chem. 81 (2009) 7639-7649 - Raman and NIR spectroscopy are able to monitor the product behavior throughout the complete annealing step during freeze-drying. The DOE approach allowed predicting the optimum combination of process and formulation parameters leading to the desired responses. Applying a mannitol/sucrose ratio of 4, without adding NaCl and processing the formulation without an annealing step, using a freezing rate of 0.9°C/min and a secondary drying temperature of 40°C resulted in efficient freeze-drying supplying end products with a residual moisture content below 2% and a mannitol hemi-hydrate content below 20%. Finally, using Monte Carlo simulations it became possible to determine how varying the factor settings around their optimum still leads to fulfilled response criteria, herewith having an idea about the probability to exceed the acceptable response limits. This multi-dimensional combination and interaction of input variables (factor ranges) leading to acceptable response criteria with an acceptable probability reflects the process design space. Copyright © 2010 Elsevier B.V. All rights reserved.

Use of a soft sensor for the fast estimation of dried cake resistance during a freeze-drying cycle.

PubMed

Bosca, Serena; Barresi, Antonello A; Fissore, Davide

2013-07-15

This paper deals with the determination of dried cake resistance in a freeze-drying process using the Smart Soft Sensor, a process analytical technology recently proposed by the authors to monitor the primary drying stage of a freeze-drying process. This sensor uses the measurement of product temperature, a mathematical model of the process, and the Kalman filter algorithm to estimate the residual amount of ice in the vial as a function of time, as well as the coefficient of heat transfer between the shelf and the product and the resistance of the dried cake to vapor flow. It does not require expensive (additional) hardware in a freeze-dryer, provided that thermocouples are available. At first, the effect of the insertion of the thermocouple in a vial on the structure of the product is investigated by means of experimental tests, comparing both sublimation rate and cake structure in vials with and without thermocouple. This is required to assess that the temperature measured by the thermocouple is the same of the product in the non-monitored vials, at least in a non-GMP environment, or when controlled nucleation methods are used. Then, results about cake resistance obtained in an extended experimental campaign with aqueous solutions containing different excipients (sucrose, mannitol and polyvinylpyrrolidone), processed in various operating conditions, are presented, with the goal to point out the accuracy of the proposed methodology. Copyright © 2013 Elsevier B.V. All rights reserved.

Expression and characterization of an antifreeze protein from the perennial rye grass, Lolium perenne.

PubMed

Lauersen, Kyle J; Brown, Alan; Middleton, Adam; Davies, Peter L; Walker, Virginia K

2011-06-01

Antifreeze proteins (AFP) are an evolutionarily diverse class of stress response products best known in certain metazoans that adopt a freeze-avoidance survival strategy. The perennial ryegrass, Lolium perenne (Lp), cannot avoid winter temperatures below the crystallization point and is thought to use its LpAFP in a freeze-tolerant strategy. In order to examine properties of LpAFP in relation to L. perenne's life history, cDNA cloning, recombinant protein characterization, ice-binding activities, gene copy number, and expression responses to low temperature were examined. Transcripts, encoded by only a few gene copies, appeared to increase in abundance after diploid plants were transferred to 4°C for 1-2 days, and in parallel with the ice recrystallization inhibition activities. Circular dichroism spectra of recombinant LpAFP showed three clear folding transition temperatures including one between 10 and 15°C, suggesting to us that folding modifications of the secreted AFP could allow the targeted degradation of the protein in planta when temperatures increase. Although LpAFP showed low thermal hysteresis activity and partitioning into ice, it was similar to AFPs from freeze-avoiding organisms in other respects. Therefore, the type of low temperature resistance strategy adopted by a particular species may not depend on the type of AFP. The independence of AFP sequence and life-history has practical implications for the development of genetically-modified crops with enhanced freeze tolerance. Copyright © 2011 Elsevier Inc. All rights reserved.

Ramp and periodic dynamics across non-Ising critical points

NASA Astrophysics Data System (ADS)

Ghosh, Roopayan; Sen, Arnab; Sengupta, K.

2018-01-01

We study ramp and periodic dynamics of ultracold bosons in an one-dimensional (1D) optical lattice which supports quantum critical points separating a uniform and a Z3 or Z4 symmetry broken density-wave ground state. Our protocol involves both linear and periodic drives which takes the system from the uniform state to the quantum critical point (for linear drive protocol) or to the ordered state and back (for periodic drive protocols) via controlled variation of a parameter of the system Hamiltonian. We provide exact numerical computation, for finite-size boson chains with L ≤24 using exact diagonalization (ED), of the excitation density D , the wave function overlap F , and the excess energy Q at the end of the drive protocol. For the linear ramp protocol, we identify the range of ramp speeds for which D and Q show Kibble-Zurek scaling. We find, based on numerical analysis with L ≤24 , that such scaling is consistent with that expected from critical exponents of the q -state Potts universality class with q =3 ,4 . For the periodic protocol, we show that the model displays near-perfect dynamical freezing at specific frequencies; at these frequencies D ,Q →0 and |F |→1 . We provide a semi-analytic explanation of such freezing behavior and relate this phenomenon to a many-body version of Stuckelberg interference. We suggest experiments which can test our theory.

The enhancement and suppression of immersion mode heterogeneous ice-nucleation by solutes.

PubMed

Whale, Thomas F; Holden, Mark A; Wilson, Theodore W; O'Sullivan, Daniel; Murray, Benjamin J

2018-05-07

Heterogeneous nucleation of ice from aqueous solutions is an important yet poorly understood process in multiple fields, not least the atmospheric sciences where it impacts the formation and properties of clouds. In the atmosphere ice-nucleating particles are usually, if not always, mixed with soluble material. However, the impact of this soluble material on ice nucleation is poorly understood. In the atmospheric community the current paradigm for freezing under mixed phase cloud conditions is that dilute solutions will not influence heterogeneous freezing. By testing combinations of nucleators and solute molecules we have demonstrated that 0.015 M solutions (predicted melting point depression <0.1 °C) of several ammonium salts can cause suspended particles of feldspars and quartz to nucleate ice up to around 3 °C warmer than they do in pure water. In contrast, dilute solutions of certain alkali metal halides can dramatically depress freezing points for the same nucleators. At 0.015 M, solutes can enhance or deactivate the ice-nucleating ability of a microcline feldspar across a range of more than 10 °C, which corresponds to a change in active site density of more than a factor of 10 5 . This concentration was chosen for a survey across multiple solutes-nucleant combinations since it had a minimal colligative impact on freezing and is relevant for activating cloud droplets. Other nucleators, for instance a silica gel, are unaffected by these 'solute effects', to within experimental uncertainty. This split in response to the presence of solutes indicates that different mechanisms of ice nucleation occur on the different nucleators or that surface modification of relevance to ice nucleation proceeds in different ways for different nucleators. These solute effects on immersion mode ice nucleation may be of importance in the atmosphere as sea salt and ammonium sulphate are common cloud condensation nuclei (CCN) for cloud droplets and are internally mixed with ice-nucleating particles in mixed-phase clouds. In addition, we propose a pathway dependence where activation of CCN at low temperatures might lead to enhanced ice formation relative to pathways where CCN activation occurs at higher temperatures prior to cooling to nucleation temperature.

The enhancement and suppression of immersion mode heterogeneous ice-nucleation by solutes

PubMed Central

Holden, Mark A.; Wilson, Theodore W.; O'Sullivan, Daniel; Murray, Benjamin J.

2018-01-01

Heterogeneous nucleation of ice from aqueous solutions is an important yet poorly understood process in multiple fields, not least the atmospheric sciences where it impacts the formation and properties of clouds. In the atmosphere ice-nucleating particles are usually, if not always, mixed with soluble material. However, the impact of this soluble material on ice nucleation is poorly understood. In the atmospheric community the current paradigm for freezing under mixed phase cloud conditions is that dilute solutions will not influence heterogeneous freezing. By testing combinations of nucleators and solute molecules we have demonstrated that 0.015 M solutions (predicted melting point depression <0.1 °C) of several ammonium salts can cause suspended particles of feldspars and quartz to nucleate ice up to around 3 °C warmer than they do in pure water. In contrast, dilute solutions of certain alkali metal halides can dramatically depress freezing points for the same nucleators. At 0.015 M, solutes can enhance or deactivate the ice-nucleating ability of a microcline feldspar across a range of more than 10 °C, which corresponds to a change in active site density of more than a factor of 105. This concentration was chosen for a survey across multiple solutes–nucleant combinations since it had a minimal colligative impact on freezing and is relevant for activating cloud droplets. Other nucleators, for instance a silica gel, are unaffected by these ‘solute effects’, to within experimental uncertainty. This split in response to the presence of solutes indicates that different mechanisms of ice nucleation occur on the different nucleators or that surface modification of relevance to ice nucleation proceeds in different ways for different nucleators. These solute effects on immersion mode ice nucleation may be of importance in the atmosphere as sea salt and ammonium sulphate are common cloud condensation nuclei (CCN) for cloud droplets and are internally mixed with ice-nucleating particles in mixed-phase clouds. In addition, we propose a pathway dependence where activation of CCN at low temperatures might lead to enhanced ice formation relative to pathways where CCN activation occurs at higher temperatures prior to cooling to nucleation temperature. PMID:29780544

Enhanced Microbial Survivability in Subzero Brines.

PubMed

Heinz, Jacob; Schirmack, Janosch; Airo, Alessandro; Kounaves, Samuel P; Schulze-Makuch, Dirk

2018-04-17

It is well known that dissolved salts can significantly lower the freezing point of water and thus extend habitability to subzero conditions. However, most investigations thus far have focused on sodium chloride as a solute. In this study, we report on the survivability of the bacterial strain Planococcus halocryophilus in sodium, magnesium, and calcium chloride or perchlorate solutions at temperatures ranging from +25°C to -30°C. In addition, we determined the survival rates of P. halocryophilus when subjected to multiple freeze/thaw cycles. We found that cells suspended in chloride-containing samples have markedly increased survival rates compared with those in perchlorate-containing samples. In both cases, the survival rates increase with lower temperatures; however, this effect is more pronounced in chloride-containing samples. Furthermore, we found that higher salt concentrations increase survival rates when cells are subjected to freeze/thaw cycles. Our findings have important implications not only for the habitability of cold environments on Earth but also for extraterrestrial environments such as that of Mars, where cold brines might exist in the subsurface and perhaps even appear temporarily at the surface such as at recurring slope lineae. Key Words: Brines-Halophile-Mars-Perchlorate-Subzero-Survival. Astrobiology 18, xxx-xxx.

Temperature-Induced Protein Release from Water-in-Oil-in-Water Double Emulsions

PubMed Central

Rojas, Edith C.; Staton, Jennifer A.; John, Vijay T.; Papadopoulos, Kyriakos D.

2009-01-01

A model water-in-oil-in-water (W1/O/W2) double emulsion was prepared by a two-step emulsification procedure and subsequently subjected to temperature changes that caused the oil phase to freeze and thaw while the two aqueous phases remained liquid. Our previous work on individual double-emulsion globules1 demonstrated that crystallizing the oil phase (O) preserves stability, while subsequent thawing triggers coalescence of the droplets of the internal aqueous phase (W1) with the external aqueous phase (W2), termed external coalescence. Activation of this instability mechanism led to instant release of fluorescently tagged bovine serum albumin (fluorescein isothiocyanate (FITC)-BSA) from the W1 droplets and into W2. These results motivated us to apply the proposed temperature-induced globule-breakage mechanism to bulk double emulsions. As expected, no phase separation of the emulsion occurred if stored at temperatures below 18 °C (freezing point of the model oil n-hexadecane), whereas oil thawing readily caused instability. Crucial variables were identified during experimentation, and found to greatly influence the behavior of bulk double emulsions following freeze-thaw cycling. Adjustment of these variables accounted for a more efficient release of the encapsulated protein. PMID:18543998

Thermalization, Freeze-out, and Noise: Deciphering Experimental Quantum Annealers

NASA Astrophysics Data System (ADS)

Marshall, Jeffrey; Rieffel, Eleanor G.; Hen, Itay

2017-12-01

By contrasting the performance of two quantum annealers operating at different temperatures, we address recent questions related to the role of temperature in these devices and their function as "Boltzmann samplers." Using a method to reliably calculate the degeneracies of the energy levels of large-scale spin-glass instances, we are able to estimate the instance-dependent effective temperature from the output of annealing runs. Our results corroborate the "freeze-out" picture which posits two regimes, one in which the final state corresponds to a Boltzmann distribution of the final Hamiltonian with a well-defined "effective temperature" determined at a freeze-out point late in the annealing schedule, and another regime in which such a distribution is not necessarily expected. We find that the output distributions of the annealers do not, in general, correspond to a classical Boltzmann distribution for the final Hamiltonian. We also find that the effective temperatures at different programing cycles fluctuate greatly, with the effect worsening with problem size. We discuss the implications of our results for the design of future quantum annealers to act as more-effective Boltzmann samplers and for the programing of such annealers.

Dynamical mechanism of antifreeze proteins to prevent ice growth

NASA Astrophysics Data System (ADS)

Kutschan, B.; Morawetz, K.; Thoms, S.

2014-08-01

The fascinating ability of algae, insects, and fishes to survive at temperatures below normal freezing is realized by antifreeze proteins (AFPs). These are surface-active molecules and interact with the diffusive water-ice interface thus preventing complete solidification. We propose a dynamical mechanism on how these proteins inhibit the freezing of water. We apply a Ginzburg-Landau-type approach to describe the phase separation in the two-component system (ice, AFP). The free-energy density involves two fields: one for the ice phase with a low AFP concentration and one for liquid water with a high AFP concentration. The time evolution of the ice reveals microstructures resulting from phase separation in the presence of AFPs. We observed a faster clustering of pre-ice structure connected to a locking of grain size by the action of AFP, which is an essentially dynamical process. The adsorption of additional water molecules is inhibited and the further growth of ice grains stopped. The interfacial energy between ice and water is lowered allowing the AFPs to form smaller critical ice nuclei. Similar to a hysteresis in magnetic materials we observe a thermodynamic hysteresis leading to a nonlinear density dependence of the freezing point depression in agreement with the experiments.

Tracking the seasonal cycle of coastal sea ice: Community-based observations and satellite remote sensing in service of societal needs

NASA Astrophysics Data System (ADS)

Eicken, Hajo; Lee, Olivia A.; Johnson, Mark A.; Pulsifer, Peter; Danielsen, Finn

2017-04-01

Break-up and freeze-up of coastal sea ice determine the timing and extent of a number of human activities, ranging from ice use by Indigenous hunters to coastal shipping. Yet, while major reductions in the extent of Arctic summer sea ice have been well studied, changes in its seasonal cycle have received less attention. Here, we discuss decadal scale changes and interannual variability in the timing of spring break-up and fall freeze-up, with a focus on coastal communities in Arctic Alaska. Observations of ice conditions by Indigenous sea-ice experts since 2006 indicate significant interannual variability in both the character and timing of freeze-up and break-up in the region. To aid in the archival and sharing of such observations, we have developed a database for community ice observations (eloka-arctic.org/sizonet). Development of this database addressed key questions ranging from community guidance on different levels of data sharing and access to the development of protocols that may lend themselves for implementation in the context of operational programs such as Global Cryosphere Watch. The lessons learned and tools developed through this effort may help foster the emergence of common observation protocols and sharing practices across the Arctic, as explored jointly with the Greenlandic PISUNA initiative and the European INTAROS project. For the Arctic Alaska region, we developed an algorithm to extract the timing of break-up and freeze-up from passive microwave satellite data, drawing on community-based observations. Data from 1979 to 2013 show break-up start arriving earlier by 5-9 days per decade and freeze-up start arriving later by 7-14 days per decade in the Chukchi and Beaufort Seas. The trends towards a shorter ice season observed over the past several decades point towards a substantial change in the winter ice regime by mid-century with incipient overlap of the end of the freeze-up and start of the break-up season as defined by coastal ice users.

Cryopreservation of canine semen - new challenges.

PubMed

Farstad, W

2009-07-01

Egg yolk (EY) protects cell membranes against cold shock, and it prevents or restores the loss of phospholipids from the membrane. EY has been widely used in semen extenders. It has been added to Tris-Glucose buffer and has been widely used for cooling and cryopreservation of canine semen. EY is not a defined entity, but a complex biological compound containing proteins, vitamins, phospholipids, glucose and antioxidants which are all potentially useful for cell membrane integrity. Unfortunately, it also is a biologically hazardous compound. Hence, whole EY needs to be replaced by other chemically defined components for semen processing in dogs. Freezing poor semen does not improve its quality, so attention must be focused on how to cope with dogs whose semen does not freeze well, and on designing individual freezing extenders for semen from such males. Furthermore, differences have been found among canid species in the ability of their spermatozoa to withstand freezing. There are differences in sperm membrane fatty acid composition among species, which may explain part of these differences. If the presence of long-chained polyunsaturated fatty acids contributes to increased membrane fluidity, this relationship may be biphasic, i.e. either too much membrane fluidity, or too little, could compromise successful sperm cryopreservation. An increase in fluidity of the outer leaflet of the plasma membrane has been shown in frozen thawed dog spermatozoa. The protective effect of exogenous lipids may lie in close association with the membrane rather than in modification or rearrangement of the membrane. This also points at lipids as an important, if not entirely new group of substances, which may substitute standard EY-based diluents in preserving sperm survival during freezing. EY-derived phospholipids or lecithin could be used to replace whole EY. Vegetable lecithin is currently investigated to avoid using substances of animal origin. EY also contains antioxidants which prevent cells from oxidative damage due to the generation of reactive oxygen species. An increasing number of publications now recognize the significance of protecting sperm from this damage during processing by using dietary or diluent supplemented antioxidants. This paper aims at looking at some of the new challenges in freezing of dog semen.

Immersion freezing in concentrated solution droplets for a variety of ice nucleating particles

NASA Astrophysics Data System (ADS)

Wex, Heike; Kohn, Monika; Grawe, Sarah; Hartmann, Susan; Hellner, Lisa; Herenz, Paul; Welti, Andre; Lohmann, Ulrike; Kanji, Zamin; Stratmann, Frank

2016-04-01

The measurement campaign LINC (Leipzig Ice Nucleation counter Comparison) was conducted in September 2015, during which ice nucleation measurements as obtained with the following instruments were compared: - LACIS (Leipzig Aerosol Cloud Interaction Simulator, see e.g. Wex et al., 2014) - PIMCA-PINC (Portable Immersion Mode Cooling Chamber together with PINC) - PINC (Portable Ice Nucleation Chamber, Chou et al., 2011) - SPIN (SPectrometer for Ice Nuclei, Droplet Measurement Technologies) While LACIS and PIMCA-PINC measured immersion freezing, PINC and SPIN varied the super-saturation during the measurements and collected data also for relative humidities below 100% RHw. A suite of different types of ice nucleating particles were examined, where particles were generated from suspensions, subsequently dried and size selected. For the following samples, data for all four instruments are available: K-feldspar, K-feldspar treated with nitric acid, Fluka-kaolinite and birch pollen. Immersion freezing measurements by LACIS and PIMCA-PINC were in excellent agreement. Respective parameterizations from these measurement were used to model the ice nucleation behavior below water vapor saturation, assuming that the process can be described as immersion freezing in concentrated solutions. This is equivalent to simply including a concentration dependent freezing point depression in the immersion freezing parameterization, as introduced for coated kaolinite particles in Wex et al. (2014). Overall, measurements performed below water vapor saturation were reproduced by the model, and it will be discussed in detail, why deviations were observed in some cases. Acknowledgement: Part of this work was funded by the DFG Research Unit FOR 1525 INUIT, grant WE 4722/1-2. Literature: Chou, C., O. Stetzer, E. Weingartner, Z. Juranyi, Z. A. Kanji, and U. Lohmann (2011), Ice nuclei properties within a Saharan dust event at the Jungfraujoch in the Swiss Alps, Atmos. Chem. Phys., 11(10), 4725-4738, doi:10.5194/acp-11-4725-2011. Wex, H., P. J. DeMott, Y. Tobo, S. Hartmann, M. Rösch, T. Clauss, L. Tomsche, D. Niedermeier, and F. Stratmann (2014), Kaolinite particles as ice nuclei: learning from the use of different kaolinite samples and different coatings, Atmos. Chem. Phys., 14, doi:10.5194/acp-14-5529-2014.

Effect of Freeze-Thaw Cycles on Soil Nitrogen Reactive Transport in a Polygonal Arctic Tundra Ecosystem at Barrow AK Using 3-D Coupled ALM-PFLOTRAN

NASA Astrophysics Data System (ADS)

Yuan, F.; Wang, G.; Painter, S. L.; Tang, G.; Xu, X.; Kumar, J.; Bisht, G.; Hammond, G. E.; Mills, R. T.; Thornton, P. E.; Wullschleger, S. D.

2017-12-01

In Arctic tundra ecosystem soil freezing-thawing is one of dominant physical processes through which biogeochemical (e.g., carbon and nitrogen) cycles are tightly coupled. Besides hydraulic transport, freezing-thawing can cause pore water movement and aqueous species gradients, which are additional mechanisms for soil nitrogen (N) reactive-transport in Tundra ecosystem. In this study, we have fully coupled an in-development ESM(i.e., Advanced Climate Model for Energy, ACME)'s Land Model (ALM) aboveground processes with a state-of-the-art massively parallel 3-D subsurface thermal-hydrology and reactive transport code, PFLOTRAN. The resulting coupled ALM-PFLOTRAN model is a Land Surface Model (LSM) capable of resolving 3-D soil thermal-hydrological-biogeochemical cycles. This specific version of PFLOTRAN has incorporated CLM-CN Converging Trophic Cascade (CTC) model and a full and simple but robust soil N cycle. It includes absorption-desorption for soil NH4+ and gas dissolving-degasing process as well. It also implements thermal-hydrology mode codes with three newly-modified freezing-thawing algorithms which can greatly improve computing performance in regarding to numerical stiffness at freezing-point. Here we tested the model in fully 3-D coupled mode at the Next Generation Ecosystem Experiment-Arctic (NGEE-Arctic) field intensive study site at the Barrow Environmental Observatory (BEO), AK. The simulations show that: (1) synchronous coupling of soil thermal-hydrology and biogeochemistry in 3-D can greatly impact ecosystem dynamics across polygonal tundra landscape; and (2) freezing-thawing cycles can add more complexity to the system, resulting in greater mobility of soil N vertically and laterally, depending upon local micro-topography. As a preliminary experiment, the model is also implemented for Pan-Arctic region in 1-D column mode (i.e. no lateral connection), showing significant differences compared to stand-alone ALM. The developed ALM-PFLOTRAN coupling codes embeded within ESM will be used for Pan-Arctic regional evaluation of climate change-caused ecosystem responses and their feedbacks to climate system at various scales.

Thermodynamical effects accompanied freezing of two water layers separated by sea ice sheet

NASA Astrophysics Data System (ADS)

Bogorodsky, Petr; Marchenko, Aleksey

2014-05-01

The process of melt pond freezing is very important for generation of sea ice cover thermodynamic and mass balance during winterperiod. However, due to significant difficulties of field measurements the available data of model estimations still have no instrumental confirmation. In May 2009 the authors carried out laboratory experiment on freezing of limited water volume in the University Centre in Svalbard ice tank. In the course of experiment fresh water layer of 27.5 cm thickness at freezing point poured on the 24 cm sea ice layer was cooled during 50 hours at the temperature -10º C and then once again during 60 hours at -20º C. For revealing process typical characteristics the data of continuous measurements of temperature and salinity in different phases were compared with data of numerical computations obtained with thermodynamic model which was formulated in the frames of 1-D equation system (infinite extension of water freezing layer) and adapted to laboratory conditions. The known surprise of the experiment became proximity of calculated and measured estimates of process dynamics that confirmed the adequacy of the problem mathematical statement (excluding probably process finale stage). This effect can be explained by formation of cracks on the upper layer of ice at sharp decreases of air temperature, which temporary compensated hydrostatic pressure growth during freezing of closed water volume. Another compensated mechanism can be migration of brine through the lower layer of ice under influence of vertical pressure gradient and also rejection of gas dissolved in water which increased its compressibility. During 110 hours cooling thickness of water layer between ice layers reduced approximately to 2 cm. According to computations this layer is not chilled completely but keeps as thin brine interlayer within ice body whose thickness (about units of mm) is determined by temperature fluctuations of cooled surface. Nevertheless, despite good coincidence of experimental and model estimates the question of existence of liquid phase under actual conditions is still open and can be clarified in a continuous laboratory experiment. This work was supported by Russian Foundation for Basic Research (Project # 14-05-00677).

Simultaneous measurement of unfrozen water content and ice content in frozen soil using gamma ray attenuation and TDR

NASA Astrophysics Data System (ADS)

Zhou, Xiaohai; Zhou, Jian; Kinzelbach, Wolfgang; Stauffer, Fritz

2014-12-01

The freezing temperature of water in soil is not constant but varies over a range determined by soil texture. Consequently, the amounts of unfrozen water and ice change with temperature in frozen soil, which in turn affects hydraulic, thermal, and mechanical properties of frozen soil. In this paper, an Am-241 gamma ray source and time-domain reflectometry (TDR) were combined to measure unfrozen water content and ice content in frozen soil simultaneously. The gamma ray attenuation was used to determine total water content. The TDR was used to determine the dielectric constant of the frozen soil. Based on a four-phase mixing model, the amount of unfrozen water content in the frozen soil could be determined. The ice content was inferred by the difference between total water content and unfrozen water content. The gamma ray attenuation and the TDR were both calibrated by a gravimetric method. Water contents measured by gamma ray attenuation and TDR in an unfrozen silt column under infiltration were compared and showed that the two methods have the same accuracy and response to changes of water content. Unidirectional column freezing experiments were performed to apply the combined method of gamma ray attenuation and TDR for measuring unfrozen water content and ice content. The measurement error of the gamma ray attenuation and TDR was around 0.02 and 0.01 m3/m3, respectively. The overestimation of unfrozen water in frozen soil by TDR alone was quantified and found to depend on the amount of ice content. The higher the ice content, the larger the overestimation. The study confirmed that the combined method could accurately determine unfrozen water content and ice content in frozen soil. The results of soil column freezing experiments indicate that total water content distribution is affected by available pore space and the freezing front advance rate. It was found that there is similarity between the soil water characteristic and the soil freezing characteristic of variably saturated soil. Unfrozen water content is independent of total water content and affected only by temperature when the freezing point is reached.

Investigation of Biodiesel Through Photopyroelectric and Dielectric-Constant Measurements as a Function of Temperature: Freezing/Melting Interval

NASA Astrophysics Data System (ADS)

Zanelato, E. B.; Machado, F. A. L.; Rangel, A. B.; Guimarães, A. O.; Vargas, H.; da Silva, E. C.; Mansanares, A. M.

2015-06-01

Biodiesel is a promising option for alternative fuels since it derives from natural and renewable materials; it is biodegradable and less polluting than fossil fuels. A gradual replacement of diesel by biodiesel has been adopted by many countries, making necessary the investigation of the physical properties of biodiesel and of its mixture in diesel. Photothermal techniques, specifically the photopyroelectric technique (PPE), have proved to be suitable in the characterization of biodiesel and of its precursor oils, as well as of the biodiesel/diesel mixtures. In this paper, we investigate thermal and electrical properties of animal fat-based biodiesel as a function of temperature, aiming to characterize the freezing/melting interval and the changes in the physical properties from the solid to the liquid phase. The samples were prepared using the transesterification method, by the ethylic route. Optical transmittance experiments were carried out in order to confirm the phase transition interval. Solid and liquid phases present distinct thermal diffusivities and conductivities, as well as dielectric constants. The PPE signal amplitude is governed by the changes in the thermal diffusivity/conductivity. As a consequence, the amplitude of the signal becomes like a step function, which is smoothed and sometimes delayed by the nucleation processes during cooling. A similar behavior is found in the dielectric constant data, which is higher in the liquid phase since the molecules have a higher degree of freedom. Both methods (PPE/dielectric constant) proved to be useful in the characterization of the freezing/melting interval, as well as to establish the distinction in the physical properties of solid and liquid phases. The methodology allowed a discussion of the cloud point and the pour point of the samples in the temperature variation interval.

Calculation of the Oxide Growth Rate of 2-1/4 Cr - 1 Mo Steel in Air and the Subsequent Measurement of the Strain Required to Crack the Oxide.

DTIC Science & Technology

1980-09-01

freezing points were measured using the prepared thermocouple and reader. It was found that over this temperature range, temperatures were measured...Manning and E. Metcalfe, "Oxidation of Ferritic Steels in Steam," International Conference on Ferritic Steels for Fast Reactor Steam Generators

Comparison of Thermal Performance Characteristics of Ammonia and Propylene Loop Heat Pipes

NASA Technical Reports Server (NTRS)

Kaya, Tarik; Baker, Charles; Ku, Jentung

2000-01-01

In this paper, experimental work performed on a breadboard Loop Heat Pipe (LHP) is presented. The test article was built by DCI for the Geoscience Laser Altimeter System (GLAS) instrument on the ICESat spacecraft. The thermal system requirements of GLAS have shown that ammonia cannot be used as the working fluid in this LHP because GLAS radiators could cool to well below the freezing point of ammonia. As a result, propylene was proposed as an alternative LHP working fluid since it has a lower freezing point than ammonia. Both working fluids were tested in the same LHP following a similar test plan in ambient conditions. The thermal performance characteristics of ammonia and propylene LHP's were then compared. In general, the propylene LHP required slightly less startup superheat 5nd less control heater power than the ammonia LHP, The thermal conductance values for the propylene LHP were also lower than the ammonia LHP. Later, the propylene LHP was tested in a thermal vacuum chamber. These tests demonstrated that propylene could meet the GLAS thermal design requirements. Design guidelines were proposed for the next flight-like Development Model (DM) LHP for thermal control of the GLAS instrument.

Using Ice Nucleating Particles to Enable Desublimation on Chilled Substrates

NASA Astrophysics Data System (ADS)

O'Brien, Julia; Failor, Kevin; Bisbano, Caitlin; Mulroe, Megan; Nath, Saurabh; Vinatzer, Boris; Boreyko, Jonathan

2017-11-01

On a subfreezing surface, nucleating embryos usually form as supercooled condensate that later freeze into ice, as opposed to desublimation. Ice nucleating particles (INPs) have been widely used to freeze existing water; however, nobody has studied how they might affect the initial mode of nucleation. Here, we show that INPs deposited on a substrate can switch the mode of embryo nucleation to desublimation, rather than supercooled condensation. Deposition was achieved by evaporating a water droplet containing INPs on a hydrophobic silicon wafer. A Peltier stage was used to cool the wafer down inside of a controlled humidity chamber, such that the desired set point temperature correlated with the dew point and onset of nucleation. Beneath a critical surface temperature, microscopy indicated that desublimation occurred on the circular patch of deposited INPs, compared to supercooled condensation outside the circle. The hydrophobic surface was then patterned with hydrophilic stripe arrays, which facilitated the deposition of stripes of INPs via the same evaporation method. The resulting array of desublimating ice stripes created dry zones free of condensation or frost in the intermediate areas, as the hygroscopic ice stripes served as overlapping humidity sinks.

Analytical solution and numerical simulation of the liquid nitrogen freezing-temperature field of a single pipe

NASA Astrophysics Data System (ADS)

Cai, Haibing; Xu, Liuxun; Yang, Yugui; Li, Longqi

2018-05-01

Artificial liquid nitrogen freezing technology is widely used in urban underground engineering due to its technical advantages, such as simple freezing system, high freezing speed, low freezing temperature, high strength of frozen soil, and absence of pollution. However, technical difficulties such as undefined range of liquid nitrogen freezing and thickness of frozen wall gradually emerge during the application process. Thus, the analytical solution of the freezing-temperature field of a single pipe is established considering the freezing temperature of soil and the constant temperature of freezing pipe wall. This solution is then applied in a liquid nitrogen freezing project. Calculation results show that the radius of freezing front of liquid nitrogen is proportional to the square root of freezing time. The radius of the freezing front also decreases with decreased the freezing temperature, and the temperature gradient of soil decreases with increased distance from the freezing pipe. The radius of cooling zone in the unfrozen area is approximately four times the radius of the freezing front. Meanwhile, the numerical simulation of the liquid nitrogen freezing-temperature field of a single pipe is conducted using the Abaqus finite-element program. Results show that the numerical simulation of soil temperature distribution law well agrees with the analytical solution, further verifies the reliability of the established analytical solution of the liquid nitrogen freezing-temperature field of a single pipe.

Water/rock interactions in experimentally simulated dirty snowball and dirty iceball cometary nuclei

NASA Technical Reports Server (NTRS)

Gooding, James L.; Allton, Judith H.

1991-01-01

In the dirty snowball model for cometary nuclei, comet-nucleus materials are regarded as mixtures of volatile ices and relatively non-volatile minerals or chemical compounds. Carbonaceous chondrite meteorites are regarded as useful analogs for the rocky component. To help elucidate the possible physical geochemistry of cometary nuclei, preliminary results are reported of calorimetric experiments with two-component systems involving carbonaceous chondrites and water ice. Based on collective knowledge of the physics of water ice, three general types of interactions can be expected between water and minerals at sub-freezing temperatures: (1) heterogeneous nucleation of ice by insoluble minerals; (2) adsorption of water vapor by hygroscopic phases; and (3) freezing- and melting-point depression of liquid water sustained by soluble minerals. The relative and absolute magnitude of all three effects are expected to vary with mineral composition.

A finite element analysis of the freeze/thaw behavior of external artery heat pipes

NASA Technical Reports Server (NTRS)

Lu, X. J.; Peterson, G. P.

1993-01-01

A two-dimensional finite element model was used to determine the freeze/thaw characteristics of an external artery heat pipe. During startup, the working fluid, which was located in the liquid channel and the circumferential wall grooves, experienced a phase transformation from a solid to a liquid state. The transient heat conduction equations with moving interfacial conditions were solved using the appropriate initial boundary conditions. The modelling results include the cross-sectional temperature distribution and the interfacial or melt front position as a function of time. A fixed grid approach was adopted in the model for the phase-change process during thawing of frozen working fluid. The interfacial position between the liquid and solid regions was found by balancing the latent heat caused by interfacial movement with the heat addition or extraction at the related grid points.

Latest developments in cryogenic safety

NASA Astrophysics Data System (ADS)

Webster, T.

1982-05-01

The Cryogenic Safety Manual, published under the auspices of the British Cryogenics Council, is summarized. Since an awareness of the physical properties of the cryogenic fluids being dealt with is considered important in directing attention to hazardous situations which may arise, the manual lists the more important properties, such as molecular weight, boiling point, and freezing point. Since hydrogen and helium are very light, the possibility arises of explosive mixtures being formed at high points in buildings. Since argon is unexpectedly heavy, its removal requires suction rather than blowing. It is also pointed out that the use of inert liquid nitrogen can lead to the creation of a noninert atmosphere which supports combustion because it contains oxygen. Attention is also given to the danger of asphyxiation posed by the growing use of inert gases.

The fast-ice growth and freezing of the bottom in the Braganzavagen Gulf (Van Mijenfjorden, Svalbard)

NASA Astrophysics Data System (ADS)

Bogorodsky, Petr; Marchenko, Aleksey; Pnyushkov, Andrey; Filchuk, Kirill; Morozov, Yevgenii; Ryzhov, Ivan

2017-04-01

The results of oceanographic and sea ice studies in the shallow Braganzavågen Gulf (Van Mijenfjorden, Svalbard) in March 2016 are presented. These studies are a continuation of observational efforts initiated by UNIS (Svalbard, Norway) in 2014. 2016 field campaign includes instrumental measurements of snow and ice properties in the fjord (e.g., ice thicknesses, temperatures, and salinities), as well as high-resolution CTD measurements within the under-ice water column. Collected observations were accompanied by freezing simulations of adjacent water and bottom ground layers performed with a one-dimensional thermodynamic model (Bogorodskii and Pnyushkov, 2015). The model uses two methods to reproduce phase transition areas - a "classic" (frontal) method for the fast ice, and transition in the continuous media (mushy zone) for the bottom sediments. Meteorological observations during the winter 2015-16 at Sveagruva (northwest coast) were used in these simulations as the atmospheric forcing. Numerical experiments were carried out for the initial salinity of 35 psu and 2 m water depth. The simulations start with the beginning of water freezing determined by a steady air temperature transition through the freezing point. The start of freezing was also verified by comparison with sea ice charts available for the Van Mijenfjorden for the period of simulations. Model simulations showed that the growth of sea ice in shallow (<1 m) areas of the basin significantly increases water salinity in the under-ice layer. For instance, at a 0.5 m depth the salinity in the under ice water layer exceeds 160 psu, which corresponds to the freezing temperature below -9C. In fact, the water salinity does not reach high values because of the horizontal mixing. However, available hydrological observations showed relatively small (0.2-0.5 m) amplitudes of tides - the major contributor to the horizontal exchange in this area. These small amplitudes likely suggest small advective salt fluxes induced by tides, and thus their little effect on the rate of ice formation at seasonal time scales. As expected, substantial water cooling in the under-ice layer leads to freezing of the bottom ground, mostly evident in areas with small depths. For example, during the cold season this freezing may be as large as 1 m at a fjord part with typical depths of 0.5 m. In general, the model shows a relativity good agreement with direct observations of fast ice properties. However, due to uncertainty in the thermodynamic properties of the ground, the quantitative description of the heat transfer processes in this layer is still incomplete and required additional clarification in the specially targeted field experiments.

Alternative aircraft fuels

NASA Technical Reports Server (NTRS)

Longwell, J. P.; Grobman, J. S.

1977-01-01

The efficient utilization of fossil fuels by future jet aircraft may necessitate the broadening of current aviation turbine fuel specifications. The most significant changes in specifications would be an increased aromatics content and a higher final boiling point in order to minimize refinery energy consumption and costs. These changes would increase the freezing point and might lower the thermal stability of the fuel, and could cause increased pollutant emissions, increased combustor liner temperatures, and poorer ignition characteristics. The effects that broadened specification fuels may have on present-day jet aircraft and engine components and the technology required to use fuels with broadened specifications are discussed.

Microgravity

NASA Image and Video Library

2001-01-24

Typical metal sample that was processed by TEMPUS (Tiegelfreies Elektromagnetisches Prozessieren Unter Schwerelosigkeit), an electromagnetic levitation facility developed by German researchers and flown on the IML-2 and MSL-1 and 1R Spacelab missions. Electromagnetic levitation is used commonly in ground-based experiments to melt and then cool metallic melts below their freezing points without solidification occurring. Sample size is limited in ground-based experiments. Research with TEMPUS aboard Spacelab allowed scientists to study the viscosity, surface tension, and other properties of several metals and alloys while undercooled (i.e., cooled below their normal solidification points). The sample is about 1 cm (2/5 inch) in diameter.

Chemical and Physical Properties of Hi-Cal-2

NASA Technical Reports Server (NTRS)

Spakowski, A. E.; Allen, Harrison, Jr.; Caves, Robert M.

1955-01-01

As part of the Navy Project Zip to consider various boron-containing materials as possible high-energy fuels, the chemical and physical properties of Hi-Cal-2 prepared by the Callery Chemical Company were evaluated at the NACA Lewis laboratory. Elemental chemical analysis, heat of combustion, vapor pressure and decomposition, freezing point, density, self ignition temperature, flash point, and blow-out velocity were determined for the fuel. Although the precision of measurement of these properties was not equal to that obtained for hydrocarbons, this special release research memorandum was prepared to make the data available as soon as possible.

Magnetic resonance tells microbiology where to go; bacterial teichoic acid protects liquid water at sub-zero temperatures

NASA Astrophysics Data System (ADS)

Rice, Charles V.; Wickham, Jason R.; Eastman, Margaret A.; Harrison, William; Pereira, Mark P.; Brown, Eric D.

2008-08-01

Numerous chemical additives lower the freezing point of water, but life at sub-zero temperatures is sustained by a limited number of biological cryoprotectants. Antifreeze proteins in fish, plants, and insects provide protection to a few degrees below freezing. Microbes have been found to survive at even lower temperatures, although, with a few exceptions, antifreeze proteins are missing. Survival has been attributed to external factors, such as high salt concentration (brine veins) and adhesion to particulates or ice crystal defects. Teichoic acid is a phosphodiester polymer ubiquitous in Gram positive bacteria, composing 50% of the mass of the bacterial cell wall and excreted into the extracellular space of biofilm communities. We have found that when bound to the peptidoglycan cell wall (wall teichoic acid) or as a free molecule (lipoteichoic acid), teichoic acid is surrounded by liquid water at temperatures significantly below freezing. Using solid-state NMR, we are unable to collect 31P CPMAS spectra for frozen solutions of lipoteichoic acid at temperatures above -60 °C. For wall teichoic acid in D2O, signals are not seen above -30 °C. These results can be explained by the presence of liquid water, which permits rapid molecular motion to remove 1H/31P dipolar coupling. 2H quadrupole echo NMR spectroscopy reveals that both liquid and solid water are present. We suggest that teichoic acids could provide a shell of liquid water around biofilms and planktonic bacteria, removing the need for brine veins to prevent bacterial freezing.

Ice-Accretion Scaling Using Water-Film Thickness Parameters

NASA Technical Reports Server (NTRS)

Anderson, David N.; Feo, Alejandro

2003-01-01

Studies were performed at INTA in Spain to determine water-film thickness on a stagnation-point probe inserted in a simulated cloud. The measurements were correlated with non-dimensional parameters describing the flow and the cloud conditions. Icing scaling tests in the NASA Glenn Icing Research Tunnel were then conducted using the Ruff scaling method with the scale velocity found by matching scale and reference values of either the INTA non-dimensional water-film thickness or a Weber number based on that film thickness. For comparison, tests were also performed using the constant drop-size Weber number and the average-velocity methods. The reference and scale models were both aluminum, 61-cm-span, NACA 0012 airfoil sections at 0 deg. AOA. The reference had a 53-cm-chord and the scale, 27 cm (1/2 size). Both models were mounted vertically in the center of the IRT test section. Tests covered a freezing fraction range of 0.28 to 1.0. Rime ice (n = 1.0) tests showed the consistency of the IRT calibration over a range of velocities. At a freezing fraction of 0.76, there was no significant difference in the scale ice shapes produced by the different methods. For freezing fractions of 0.40, 0.52 and 0.61, somewhat better agreement with the reference horn angles was typically achieved with the average-velocity and constant-film thickness methods than when either of the two Weber numbers was matched to the reference value. At a freezing fraction of 0.28, the four methods were judged equal in providing simulations of the reference shape.

Repeated vitrification/warming of human sperm gives better results than repeated slow programmable freezing

PubMed Central

Vutyavanich, Teraporn; Lattiwongsakorn, Worashorn; Piromlertamorn, Waraporn; Samchimchom, Sudarat

2012-01-01

In this study, we compared the effects of repeated freezing/thawing of human sperm by our in-house method of rapid freezing with slow programmable freezing. Sperm samples from 11 normozoospermic subjects were processed through density gradients and divided into three aliquots: non-frozen, rapid freezing and slow programmable freezing. Sperm in the rapid freezing group had better motility and viability than those in the slow freezing group (P<0.01) after the first, second and third cycles of freezing/thawing, but there was no difference in morphology. In the second experiment, rapid freezing was repeated three times in 20 subjects. The samples from each thawing cycle were evaluated for DNA fragmentation using the alkaline comet assay. DNA fragmentation began to increase considerably after the second cycle of freezing/thawing, but to a level that was not clinically important. In the third experiment, rapid freezing was done repeatedly in 10 subjects, until no motile sperm were observed after thawing. The median number of repeated freezing/thawing that yielded no motile sperm was seven (range: 5–8, mean: 6.8). In conclusion, we demonstrated that repeated freezing/thawing of processed semen using our rapid freezing method gave better results than standard slow programmable freezing. This method can help maximize the usage of precious cryopreserved sperm samples in assisted reproduction technology. PMID:23064685

Characteristics of sugar surfactants in stabilizing proteins during freeze-thawing and freeze-drying.

PubMed

Imamura, Koreyoshi; Murai, Katsuyuki; Korehisa, Tamayo; Shimizu, Noriyuki; Yamahira, Ryo; Matsuura, Tsutashi; Tada, Hiroko; Imanaka, Hiroyuki; Ishida, Naoyuki; Nakanishi, Kazuhiro

2014-06-01

Sugar surfactants with different alkyl chain lengths and sugar head groups were compared for their protein-stabilizing effect during freeze-thawing and freeze-drying. Six enzymes, different in terms of tolerance against inactivation because of freeze-thawing and freeze-drying, were used as model proteins. The enzyme activities that remained after freeze-thawing and freeze-drying in the presence of a sugar surfactant were measured for different types and concentrations of sugar surfactants. Sugar surfactants stabilized all of the tested enzymes both during freeze-thawing and freeze-drying, and a one or two order higher amount of added sugar surfactant was required for achieving protein stabilization during freeze-drying than for the cryoprotection. The comprehensive comparison showed that the C10-C12 esters of sucrose or trehalose were the most effective through the freeze-drying process: the remaining enzyme activities after freeze-thawing and freeze-drying increased at the sugar ester concentrations of 1-10 and 10-100 μM, respectively, and increased to a greater extent than for the other surfactants at higher concentrations. Results also indicate that, when a decent amount of sugar was also added, the protein-stabilizing effect of a small amount of sugar ester through the freeze-drying process could be enhanced. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

The ability of the Antarctic nematode Panagrolaimus davidi to survive intracellular freezing is dependent upon nutritional status.

PubMed

Raymond, Mélianie R; Wharton, David A

2013-02-01

The Antarctic nematode Panagrolaimus davidi is the best documented example of an animal surviving intracellular freezing and the only animal so far shown to survive such freezing throughout its tissues. However, a recent study found that after exposure to a freezing stress that produced intracellular freezing in a proportion of nematodes, the resulting survival levels could be explained if those nematodes that froze intracellularly had died. We have thus re-examined the survival of intracellular freezing in this nematode. The ability to survive a freezing exposure that is likely to produce intracellular freezing (freezing at -10 °C) declines with culture age. In cultures that are fed regularly, the ability to survive freezing at -10 °C increases, but in starved cultures freezing survival declines. Survival of intracellular freezing in fed cultures was confirmed using cryomicroscopy, staining of cells with vital dyes and by freeze substitution and transmission electron microscopy. We have thus confirmed that P. davidi can survive intracellular freezing and shown that this ability is dependent upon them being well fed. The effect of culture conditions on the nutrient status of the nematodes should thus be an important factor in the design of experiments.

Emerging techniques for assisting and accelerating food freezing processes: A review of recent research progresses.

PubMed

Cheng, Lina; Sun, Da-Wen; Zhu, Zhiwei; Zhang, Zi

2017-03-04

Freezing plays an important role in food preservation and the emergence of rapid freezing technologies can be highly beneficial to the food industry. This paper reviews some novel food freezing technologies, including high-pressure freezing (HPF), ultrasound-assisted freezing (UAF), electrically disturbed freezing (EF) and magnetically disturbed freezing (MF), microwave-assisted freezing (MWF), and osmo-dehydro-freezing (ODF). HPF and UAF can initiate ice nucleation rapidly, leading to uniform distribution of ice crystals and the control of their size and shape. Specifically, the former is focused on increasing the degree of supercooling, whereas the latter aims to decrease it. Direct current electric freezing (DC-EF) and alternating current electric freezing (AC-EF) exhibit different effects on ice nucleation. DC-EF can promote ice nucleation and AC-EF has the opposite effect. Furthermore, ODF has been successfully used for freezing various vegetables and fruit. MWF cannot control the nucleation temperature, but can decrease supercooling degree, thus decreasing the size of ice crystals. The heat and mass transfer processes during ODF have been investigated experimentally and modeled mathematically. More studies should be carried out to understand the effects of these technologies on food freezing process.

Site-Dependent Fluorescence Decay of Malachite Green Doped in Onion Cell

NASA Astrophysics Data System (ADS)

Nakatsuka, Hiroki; Sekine, Masaya; Suzuki, Yuji; Hattori, Toshiaki

1999-03-01

Time-resolved fluorescence measurements of malachite green dye moleculesdoped in onion cells were carried out.The fluorescence decay time was dependent on the individual cell and on theposition of the dye in a cell, which reflect the microscopic dynamics of each boundsite.Upon cooling, the decay time increased and this increase was accelerated ataround the freezing point of the onion cell.

How Is the Freezing Point of a Binary Mixture of Liquids Related to the Composition? A Guided Inquiry Experiment

ERIC Educational Resources Information Center

Hunnicutt, Sally S.; Grushow, Alexander; Whitnell, Rob

2017-01-01

The principles of process-oriented guided inquiry learning (POGIL) are applied to a binary solid-liquid mixtures experiment. Over the course of two learning cycles, students predict, measure, and model the phase diagram of a mixture of fatty acids. The enthalpy of fusion of each fatty acid is determined from the results. This guided inquiry…

Individualized cryoballoon energy pulmonary vein isolation guided by real-time pulmonary vein recordings, the randomized ICE-T trial.

PubMed

Chun, K R Julian; Stich, Marie; Fürnkranz, Alexander; Bordignon, Stefano; Perrotta, Laura; Dugo, Daniela; Bologna, Fabrizio; Schmidt, Boris

2017-04-01

The ideal energy dosing remains unclear in second-generation cryoballoon (CB) pulmonary vein isolation (PVI). We aimed to investigate the effect of an individualized dosing strategy based on time to PVI (TTI). The purpose of this study was to prospectively investigate the safety and efficacy of individualized PVI using the second-generation CB guided by real-time pulmonary vein recordings. Two groups were prospectively randomized: ICE-T group: if TTI <75 seconds, then no bonus freeze; and control group: acute PVI followed by 1 empiric bonus freeze. Freeze duration was set to 240 seconds. The primary end point was single procedure sinus rhythm after 12 months (blanking period 3 months). Secondary end points included procedural data, complications, and biomarker release. In total, 100 patients with paroxysmal atrial fibrillation were randomized. The primary end point was not different (88% vs 82%). Procedure and fluoroscopy times were significantly shorter in the ICE-T group (70 ± 20 minutes vs 89 ± 21 minutes; P < .001 and 10.6 ± 3.9 minutes vs 12.7 ± 5.5 minutes; P = .03). More complications occurred in the control group (n = 9 vs n = 3) (persistent phrenic nerve injury: n = 1 vs n = 0; transient phrenic nerve injury: n = 5 vs n = 2; esophageal lesions: n = 3 vs n = 1). Postablation troponin T levels were not different (ICE-T group vs control group: 1035 ± 402 ng/L vs 1219 ± 509 ng/L; P = .099), whereas a significantly lower lactic acid dehydrogenase release was observed in the ICE-T group (259 ± 47 U/L vs 282 ± 57 U/L; P = .038). Multivariate analysis identified a mean TTI of >43 seconds as the only independent predictor of recurrent atrial tachyarrhythmia. The individualized CB PVI strategy allows faster atrial fibrillation ablation without affecting the favorable clinical outcome. A short TTI appears to predict freedom from recurrent atrial tachyarrhythmia. Copyright © 2016 Heart Rhythm Society. Published by Elsevier Inc. All rights reserved.

Freezing and thawing or freezing, thawing, and aging effects on beef tenderness.

PubMed

Grayson, A L; King, D A; Shackelford, S D; Koohmaraie, M; Wheeler, T L

2014-06-01

The objective of this study was to determine the effect of freezing and thawing or freezing and thawing with an additional aging period after frozen storage on the tenderness of longissimus lumborum (LL) and semitendinosus (ST) steaks relative to aged, fresh steaks. Left-side LL and ST (n = 35 each) were obtained from U.S. Select carcasses classified at the grading stand by the U.S. Meat Animal Research Center visible and near-infrared spectroscopy tenderness system to have predicted slice shear force greater than 16.5 kg at 14 d postmortem. At 2 d postmortem, 2.54 cm thick steaks were cut from each muscle and assigned to 1 of the following treatments: 2 d fresh (2FRESH), 2 d freeze + thaw (2FREEZE), 2 d freeze + thaw + 12 d age (2FREEZE+12AGE), 14 d fresh (14FRESH), 14 d freeze + thaw (14FREEZE), 14 d freeze + thaw + 14 d age (14FREEZE+14AGE), and 28 d fresh (28FRESH). Steaks assigned to a freezing treatment were frozen at -26°C for 30 d before thawing/cooking or thawing with an additional aging period at 2°C. Slice shear force for LL and ST was lower (P < 0.01) for 2FREEZE (27.4 and 24.5 kg) and 14FREEZE (22.4 and 22.4 kg) compared to 2FRESH (33.0 and 29.2 kg) and 14FRESH (25.3 and 25.5 kg), respectively. Slice shear force for LL and ST was lower (P < 0.01) for 2FREEZE+12AGE (17.8 and 20.8 kg) and 14FREEZE+14AGE (14.6 and 19.0 kg) compared to 14FRESH (25.3 and 25.5 kg) and 28FRESH (18.7 and 21.7 kg), respectively. Desmin degradation for LL was not different (P > 0.05) between 2FREEZE (21.0%) and 2FRESH (14.6%) or between 14FREEZE (40.4%) and 14FRESH (38.4%); however, desmin degradation was higher (P < 0.06) in 2FREEZE+12AGE (46.7%) and 14FREEZE+14AGE (71.1%) when compared to 14FRESH (38.4%) and 28FRESH (60.5%), respectively. Cooking loss for LL was higher (P < 0.01) in 2FREEZE+12AGE (15.2%) compared to 14FRESH (14.0%) but was not different (P > 0.05) between 14FREEZE+14AGE (15.0%) and 28FRESH (14.3%). Freezing and thawing or a combination of freezing, thawing, and aging resulted in increased tenderness for LL and ST steaks when compared to fresh steaks with the same aging time. These results indicate freezing could be incorporated into normal commercial product distribution processes to improve the consistency of meat tenderness. Researchers who freeze steaks before tenderness assessment should be aware and acknowledge that freezing affects tenderness data.

Some statistics of freezing precipitation and rime for the territory of the former USSR from ground-based weather observations

NASA Astrophysics Data System (ADS)

Bezrukova, Natalia A.; Jeck, Richard K.; Khalili, Marat F.; Minina, Ludmila S.; Naumov, Alexander Ya.; Stulov, Evgeny A.

2006-11-01

This work is a continuation of the previous climatological study of freezing precipitation and rime over the USSR territory [ Bezrukova, N.A., Minina, L.S., Naumov, A.Ya., 2000. Freezing precipitation climatology in the former European USSR. Proceedings of the 13th International Conference on Clouds and Precipitation, pp.737-739, Reno, Nevada, USA, 14-18 August 2000; Bezrukova, N.A., Jeck, R.K., Minina, L.S., Khalili, M.F., Stulov, E.A., 2004. 10-year Statistics on Freezing Precipitation across the former USSR from surface weather observations. Proceedings of the 14th International Conference on Clouds and Precipitation, pp.731-734, Bologna, Italy, 19-23 August 2004.] aimed at creating an atlas of the frequency of these phenomena. This study gives considerable information about and a statistical analysis of freezing precipitation and rime events observed over the territory of the former USSR during a decade (1981-1990) and over the European territory of the USSR during two decades (1971-1990). This paper intends to draw the attention of the reader to the atlas and statistics by showing some interesting points. The authors used the data provided by the ground-based weather stations involved in the international exchange of meteorological data. The USSR network's Monthly Meteorological Tables (1971-1990) [Monthly Meteorological Tables, 1971-1990. Part 1, Novosibirsk-Obninsk. (in Russian).] comprising selected daily ground-based meteorological observations from more than 220 stations served as a basis for the analysis. All the types of freezing precipitation (FP) events were given as WMO Codes 56, 57, 66, 67, 24 and freezing fog (FF) deposited rime as WMO Codes 48, 49. The entire territory was divided into six major regions: the Arctic, the European part of the USSR, the Trans-Caucasus, Central Asia, Siberia, and the Far East. The frequency and distribution of events by regions versus temperature, atmospheric pressure, clouds base height, and some other meteorological parameters concerned were obtained. Climatic maps of annual mean, monthly mean, and seasonal mean occurrences of FP and FF were constructed for these regions. The study also analyzes the space-time variability of monthly mean ice-coating duration in hours for the 20-year period of 1971-1990 as observed at over 80 stations in the European part of the USSR (ET), and climatic maps of annual mean and monthly mean ice coating duration for the ET are constructed. The correlation between ice coating duration and height has been evaluated.

Rapid determination of vial heat transfer parameters using tunable diode laser absorption spectroscopy (TDLAS) in response to step-changes in pressure set-point during freeze-drying.

PubMed

Kuu, Wei Y; Nail, Steven L; Sacha, Gregory

2009-03-01

The purpose of this study was to perform a rapid determination of vial heat transfer parameters, that is, the contact parameter K(cs) and the separation distance l(v), using the sublimation rate profiles measured by tunable diode laser absorption spectroscopy (TDLAS). In this study, each size of vial was filled with pure water followed by a freeze-drying cycle using a LyoStar II dryer (FTS Systems) with step-changes of the chamber pressure set-point at to 25, 50, 100, 200, 300, and 400 mTorr. K(cs) was independently determined by nonlinear parameter estimation using the sublimation rates measured at the pressure set-point of 25 mTorr. After obtaining K(cs), the l(v) value for each vial size was determined by nonlinear parameter estimation using the pooled sublimation rate profiles obtained at 25 to 400 mTorr. The vial heat transfer coefficient K(v), as a function of the chamber pressure, was readily calculated, using the obtained K(cs) and l(v) values. It is interesting to note the significant difference in K(v) of two similar types of 10 mL Schott tubing vials, primary due to the geometry of the vial-bottom, as demonstrated by the images of the contact areas of the vial-bottom. (c) 2008 Wiley-Liss, Inc. and the American Pharmacists Association

Supercapacitor Electrolyte Solvents with Liquid Range Below -80 C

NASA Technical Reports Server (NTRS)

Brandon, Erik; Smart, Marshall; West, William

2010-01-01

A previous NASA Tech Brief ["Low-Temperature Supercapacitors" (NPO-44386) NASA Tech Briefs, Vol. 32, No 7 (July 2008), page 32] detailed ongoing efforts to develop non-aqueous supercapacitor electrolytes capable of supporting operation at temperatures below commercially available cells (which are typically limited to charging and discharging at > or equal to -40 C). These electrolyte systems may enable energy storage and power delivery for systems operating in extreme environments, such as those encountered in the Polar regions on Earth or in the exploration of space. Supercapacitors using these electrolytes may also offer improved power delivery performance at moderately low temperatures (e.g. -40 to 0 C) relative to currently available cells, offering improved cold-cranking and cold-weather acceleration capabilities for electrical or hybrid vehicles. Supercapacitors store charge at the electrochemical double-layer, formed at the interface between a high surface area electrode material and a liquid electrolyte. The current approach to extending the low-temperature limit of the electrolyte focuses on using binary solvent systems comprising a high-dielectric-constant component (such as acetonitrile) in conjunction with a low-melting-point co-solvent (such as organic formates, esters, and ethers) to depress the freezing point of the system, while maintaining sufficient solubility of the salt. Recent efforts in this area have led to the identification of an electrolyte solvent formulation with a freezing point of -85.7 C, which is achieved by using a 1:1 by volume ratio of acetonitrile to 1,3-dioxolane

Cognitive Factors Affecting Freeze-like Behavior in Humans.

PubMed

Alban, Michael W; Pocknell, Victoria

2017-01-01

Contemporary research on survival-related defensive behaviors has identified physiological markers of freeze/flight/fight. Our research focused on cognitive factors associated with freeze-like behavior in humans. Study 1 tested if an explicit decision to freeze is associated with the psychophysiological state of freezing. Heart rate deceleration occurred when participants chose to freeze. Study 2 varied the efficacy of freezing relative to other defense options and found "freeze" was responsive to variations in the perceived effectiveness of alternative actions. Study 3 tested if individual differences in motivational orientation affect preference for a "freeze" option when the efficacy of options is held constant. A trend in the predicted direction suggested that naturally occurring cognitions led loss-avoiders to select "freeze" more often than reward-seekers. In combination, our attention to the cognitive factors affecting freeze-like behavior in humans represents a preliminary step in addressing an important but neglected research area.

The Coolest Landscape on Mars or Earth

NASA Image and Video Library

2016-12-07

Many Martian landscapes contain features that are familiar to ones we find on Earth, like river valleys, cliffs, glaciers and volcanos. However, Mars has an exotic side too, with landscapes that are alien to Earthlings. This image shows one of these exotic locales at the South Pole. The polar cap is made from carbon dioxide (dry ice), which does not occur naturally on the Earth. The circular pits are holes in this dry ice layer that expand by a few meters each Martian year. New dry ice is constantly being added to this landscape by freezing directly out of the carbon dioxide atmosphere or falling as snow. Freezing out the atmosphere like this limits how cold the surface can get to the frost point at -130 degrees Celsius (-200 F). Nowhere on Mars can ever get any colder this, making this this coolest landscape on Earth and Mars combined. http://photojournal.jpl.nasa.gov/catalog/PIA21216

Spacecraft Radiator Freeze Protection Using a Regenerative Heat Exchanger

NASA Technical Reports Server (NTRS)

Ungar, Eugene K.; Schunk, Richard G.

2011-01-01

An active thermal control system architecture has been modified to include a regenerative heat exchanger (regenerator) inboard of the radiator. Rather than using a radiator bypass valve a regenerative heat exchanger is placed inboard of the radiators. A regenerator cold side bypass valve is used to set the return temperature. During operation, the regenerator bypass flow is varied, mixing cold radiator return fluid and warm regenerator outlet fluid to maintain the system setpoint. At the lowest heat load for stable operation, the bypass flow is closed off, sending all of the flow through the regenerator. This lowers the radiator inlet temperature well below the system set-point while maintaining full flow through the radiators. By using a regenerator bypass flow control to maintain system setpoint, the required minimum heat load to avoid radiator freezing can be reduced by more than half compared to a radiator bypass system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pandey, Ravindra; Usui, Kota; Livingstone, Ruth A.

Ice-nucleating organisms play important roles in the environment. With their ability to induce ice formation at temperatures just below the ice melting point, bacteria such as Pseudomonas syringae attack plants through frost damage using specialized ice-nucleating proteins. Besides the impact on agriculture and microbial ecology, airborne P. syringae can affect atmospheric glaciation processes, with consequences for cloud evolution, precipitation, and climate. Biogenic ice nucleation is also relevant for artificial snow production and for biomimetic materials for controlled interfacial freezing. We use interface-specific sum frequency generation (SFG) spectroscopy to show that hydrogen bonding at the water-bacteria contact imposes structural ordering onmore » the adjacent water network. Experimental SFG data and molecular dynamics simulations demonstrate that ice active sites within P. syringae feature unique hydrophilic-hydrophobic patterns to enhance ice nucleation. Finally, the freezing transition is further facilitated by the highly effective removal of latent heat from the nucleation site, as apparent from time-resolved SFG spectroscopy.« less

Segregation effects during solidification in weightless melts

NASA Technical Reports Server (NTRS)

Li, C.

1973-01-01

Two types of melt segregation effects were studied: (1) evaporative segregation, or segregation due to surface evaporation; and (2) freezing segregation, or segregation due to liquid-solid phase transformation. These segregation effects are closely related. In fact, evaporative segregation always precedes freezing segregation to some degree and must often be studied prior to performing meaningful solidification experiments. This is particularly true since evaporation may cause the melt composition, at least at the critical surface regions or layers to be affected manyfold within seconds so that the surface region or layer melting point and other thermophysical properties, nucleation characteristics, base for undercooling, and critical velocity to avoid constitutional supercooling, may be completely unexpected. An important objective was, therefore, to develop the necessary normal evaporation equations for predicting the compositional changes within specified times at temperature and to correlate these equations with actual experimental data collected from the literature.

Mass production of shaped particles through vortex ring freezing

NASA Astrophysics Data System (ADS)

An, Duo; Warning, Alex; Yancey, Kenneth G.; Chang, Chun-Ti; Kern, Vanessa R.; Datta, Ashim K.; Steen, Paul H.; Luo, Dan; Ma, Minglin

2016-08-01

A vortex ring is a torus-shaped fluidic vortex. During its formation, the fluid experiences a rich variety of intriguing geometrical intermediates from spherical to toroidal. Here we show that these constantly changing intermediates can be `frozen' at controlled time points into particles with various unusual and unprecedented shapes. These novel vortex ring-derived particles, are mass-produced by employing a simple and inexpensive electrospraying technique, with their sizes well controlled from hundreds of microns to millimetres. Guided further by theoretical analyses and a laminar multiphase fluid flow simulation, we show that this freezing approach is applicable to a broad range of materials from organic polysaccharides to inorganic nanoparticles. We demonstrate the unique advantages of these vortex ring-derived particles in several applications including cell encapsulation, three-dimensional cell culture, and cell-free protein production. Moreover, compartmentalization and ordered-structures composed of these novel particles are all achieved, creating opportunities to engineer more sophisticated hierarchical materials.

Microstructure of bentonite in iron ore green pellets.

PubMed

Bhuiyan, Iftekhar U; Mouzon, Johanne; Schröppel, Birgit; Kaech, Andres; Dobryden, Illia; Forsmo, Seija P E; Hedlund, Jonas

2014-02-01

Sodium-activated calcium bentonite is used as a binder in iron ore pellets and is known to increase strength of both wet and dry iron ore green pellets. In this article, the microstructure of bentonite in magnetite pellets is revealed for the first time using scanning electron microscopy. The microstructure of bentonite in wet and dry iron ore pellets, as well as in distilled water, was imaged by various imaging techniques (e.g., imaging at low voltage with monochromatic and decelerated beam or low loss backscattered electrons) and cryogenic methods (i.e., high pressure freezing and plunge freezing in liquid ethane). In wet iron ore green pellets, clay tactoids (stacks of parallel primary clay platelets) were very well dispersed and formed a voluminous network occupying the space available between mineral particles. When the pellet was dried, bentonite was drawn to the contact points between the particles and formed solid bridges, which impart strength to the solid compact.

The implementation of a Hazard Analysis and Critical Control Point management system in a peanut butter ice cream plant.

PubMed

Hung, Yu-Ting; Liu, Chi-Te; Peng, I-Chen; Hsu, Chin; Yu, Roch-Chui; Cheng, Kuan-Chen

2015-09-01

To ensure the safety of the peanut butter ice cream manufacture, a Hazard Analysis and Critical Control Point (HACCP) plan has been designed and applied to the production process. Potential biological, chemical, and physical hazards in each manufacturing procedure were identified. Critical control points for the peanut butter ice cream were then determined as the pasteurization and freezing process. The establishment of a monitoring system, corrective actions, verification procedures, and documentation and record keeping were followed to complete the HACCP program. The results of this study indicate that implementing the HACCP system in food industries can effectively enhance food safety and quality while improving the production management. Copyright © 2015. Published by Elsevier B.V.

Response of seasonal soil freeze depth to climate change across China

NASA Astrophysics Data System (ADS)

Peng, Xiaoqing; Zhang, Tingjun; Frauenfeld, Oliver W.; Wang, Kang; Cao, Bin; Zhong, Xinyue; Su, Hang; Mu, Cuicui

2017-05-01

The response of seasonal soil freeze depth to climate change has repercussions for the surface energy and water balance, ecosystems, the carbon cycle, and soil nutrient exchange. Despite its importance, the response of soil freeze depth to climate change is largely unknown. This study employs the Stefan solution and observations from 845 meteorological stations to investigate the response of variations in soil freeze depth to climate change across China. Observations include daily air temperatures, daily soil temperatures at various depths, mean monthly gridded air temperatures, and the normalized difference vegetation index. Results show that soil freeze depth decreased significantly at a rate of -0.18 ± 0.03 cm yr-1, resulting in a net decrease of 8.05 ± 1.5 cm over 1967-2012 across China. On the regional scale, soil freeze depth decreases varied between 0.0 and 0.4 cm yr-1 in most parts of China during 1950-2009. By investigating potential climatic and environmental driving factors of soil freeze depth variability, we find that mean annual air temperature and ground surface temperature, air thawing index, ground surface thawing index, and vegetation growth are all negatively associated with soil freeze depth. Changes in snow depth are not correlated with soil freeze depth. Air and ground surface freezing indices are positively correlated with soil freeze depth. Comparing these potential driving factors of soil freeze depth, we find that freezing index and vegetation growth are more strongly correlated with soil freeze depth, while snow depth is not significant. We conclude that air temperature increases are responsible for the decrease in seasonal freeze depth. These results are important for understanding the soil freeze-thaw dynamics and the impacts of soil freeze depth on ecosystem and hydrological process.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akkelin, S.V.; Sinyukov, Yu.M.

A method allowing analysis of the overpopulation of phase space in heavy ion collisions in a model-independent way is proposed within the hydrodynamic approach. It makes it possible to extract a chemical potential of thermal pions at freeze-out, irrespective of the form of freeze-out (isothermal) hypersurface in Minkowski space and transverse flows on it. The contributions of resonance (with masses up to 2 GeV) decays to spectra, interferometry volumes, and phase-space densities are calculated and discussed in detail. The estimates of average phase-space densities and chemical potentials of thermal pions are obtained for SPS and RHIC energies. They demonstrate thatmore » multibosonic phenomena at those energies might be considered as a correction factor rather than as a significant physical effect. The analysis of the evolution of the pion average phase-space density in chemically frozen hadron systems shows that it is almost constant or slightly increases with time while the particle density and phase-space density at each space point decreases rapidly during the system's expansion. We found that, unlike the particle density, the average phase-space density has no direct link to the freeze-out criterion and final thermodynamic parameters, being connected rather to the initial phase-space density of hadronic matter formed in relativistic nucleus-nucleus collisions.« less

Noncontact Infrared-Mediated Heat Transfer During Continuous Freeze-Drying of Unit Doses.

PubMed

Van Bockstal, Pieter-Jan; De Meyer, Laurens; Corver, Jos; Vervaet, Chris; De Beer, Thomas

2017-01-01

Recently, an innovative continuous freeze-drying concept for unit doses was proposed, based on spinning the vials during freezing. An efficient heat transfer during drying is essential to continuously process these spin frozen vials. Therefore, the applicability of noncontact infrared (IR) radiation was examined. The impact of several process and formulation variables on the mass of sublimed ice after 15 min of primary drying (i.e., sublimation rate) and the total drying time was examined. Two experimental designs were performed in which electrical power to the IR heaters, distance between the IR heaters and the spin frozen vial, chamber pressure, product layer thickness, and 5 model formulations were included as factors. A near-infrared spectroscopy method was developed to determine the end point of primary and secondary drying. The sublimation rate was mainly influenced by the electrical power to the IR heaters and the distance between the IR heaters and the vial. The layer thickness had the largest effect on total drying time. The chamber pressure and the 5 model formulations had no significant impact on sublimation rate and total drying time, respectively. This study shows that IR radiation is suitable to provide the energy during the continuous processing of spin frozen vials. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Supercooling ability is surprisingly invariable in eggs of the land snail Cantareus aspersus.

PubMed

Ansart, Armelle; Madec, Luc; Vernon, Philippe

2007-02-01

From an ontogenetic point of view, invertebrate eggs are generally the most freezing intolerant stage of a species. Development state, water content and acclimation may affect their supercooling ability. In this study, we measured fresh mass, water content and temperature of crystallisation (T(c)) of eggs of the edible land snail Cantareus aspersus, depending on its form ("aspersa"vs. "maxima"), incubation temperature (20, 12 and 7 degrees C) and physiological age (as part of the complete development). We also tested their tolerance to freezing. Despite a high number of individual observations (n=759) and significant differences of fresh mass and water content between both subspecies, no effect of origin, incubation temperature or development state has been found in this study. T(c) remained constant whatever the condition, with an overall mean of -5.40+/-0.24 degrees C (mean+/-SD). We suggest that fresh mass is important, a high water content and a constantly wet surface confer to land snail eggs a poor ability to supercool. Moreover, the presence of ice nucleating agents at the egg surface (microorganisms present in the soil, calcium carbonate crystals of the egg shell) might induce freezing. Thus, considering the present results, to delay hatching by cryopreservation of eggs does not seem possible.

Preparation, mechanical property and cytocompatibility of freeze-cast porous calcium phosphate ceramics reinforced by phosphate-based glass.

PubMed

Yang, Yanqiu; He, Fupo; Ye, Jiandong

2016-12-01

In this study, phosphate-based glass (PG) was used as a sintering aid for freeze-cast porous biphasic calcium phosphate (BCP) ceramic, which was sintered under a lower temperature (1000°C). The phase composition, pore structure, compressive strength, and cytocompatibility of calcium phosphate composite ceramics (PG-BCP) were evaluated. The results indicated that PG additive reacted with calcium phosphate during the sintering process, forming β-Ca2P2O7; the ions of sodium and magnesium from PG partially substituted the calcium sites of β-calcium phosphate in BCP. The PG-BCP showed good cytocompatibility. The pore width of the porous PG-BCP ceramics was around 50μm, regardless of the amount of PG sintering aid. As the content of PG increased from 0wt.% to 15wt.%, the compressive strength of PG-BCP increased from 0.02 MP to 0.28MPa. When the PG additive was 17.5wt.%, the compressive strength of PG-BCP dramatically increased to 5.66MPa. Addition of 15wt.% PG was the critical point for the properties of PG-BCP. PG is considered as an effective sintering aid for freeze-cast porous bioceramics. Copyright © 2016 Elsevier B.V. All rights reserved.

Retained functional integrity of bull spermatozoa after double freezing and thawing using PureSperm density gradient centrifugation.

PubMed

Maxwell, W M C; Parrilla, I; Caballero, I; Garcia, E; Roca, J; Martinez, E A; Vazquez, J M; Rath, D

2007-10-01

The main aim of this study was to compare the motility and functional integrity of bull spermatozoa after single and double freezing and thawing. The viability and morphological integrity of spermatozoa selected by PureSperm density gradient centrifugation after cryopreservation of bovine semen in two commercial extenders (Experiment 1) and the function of bull spermatozoa before and after a second freezing and thawing assisted by PureSperm selection (Experiment 2) were examined. On average, 35.8 +/- 12.1% of sperm loaded onto the PureSperm density gradient were recovered after centrifugation. In Experiment 1, post-thaw motility and acrosome integrity were higher for spermatozoa frozen in Tris-egg yolk extender than in AndroMed, whether the assessments were made immediately after thawing [80.4 +/- 12.7 vs 47.6 +/- 19.0% motile and 78.8 +/- 8.3 vs 50.1 +/- 19.5% normal apical ridge (NAR), p < 0.05] or after preparation on the gradient (83.3 +/- 8.6 vs 69.4 +/- 15.9% motile and 89.5 +/- 7.2 vs 69.1 +/- 11.4% NAR, p < 0.05). For semen frozen in Tris-egg yolk extender, selection on the PureSperm gradient did not influence total motility but significantly improved the proportion of acrosome-intact spermatozoa. After the gradient, both the total motility and percentage of normal acrosomes increased for spermatozoa frozen in AndroMed (Minitüb Tiefenbach, Germany). In Experiment 2, there was no difference in sperm motility after the first and second freeze-thawing (82.9 +/- 12.7 vs 68.8 +/- 18.7%). However, the proportion of acrosome-intact spermatozoa was significantly improved by selection through the PureSperm gradient, whether measured by phase contrast microscopy (78.9 +/- 9.7 vs 90.4 +/- 4.0% NAR, p < 0.05) or flow cytometry (53.4 +/- 11.7 vs 76.3 +/- 6.0% viable acrosome-intact spermatozoa, p < 0.001). The improvement in the percentage of spermatozoa with normal acrosomes was maintained after resuspension in the cooling extender and cooling to 4 degrees C (88.2 +/- 6.2) and after re-freezing and thawing (83.6 +/- 6.56% NAR). However, flow cytometric assessment of the sperm membranes revealed a decline in the percentage of viable spermatozoa with intact membranes after the second freezing and thawing compared with after gradient centrifugation (76.3 +/- 6.0% vs 46.6 +/- 6.6%, p < 0.001) to levels equivalent to those obtained after the first round of freeze-thawing (53.4 +/- 11.7% viable acrosome-intact spermatozoa). Sperm movement characteristics assessed by computer-assisted analysis were unaffected in the population selected on the PureSperm gradients but declined after cooling of the selected and extended spermatozoa to 4 degrees C. There was no further change in these kinematic measurements after the cooled spermatozoa had undergone the second round of freeze-thawing. These results demonstrate that bull semen can be frozen and thawed, followed by a second freeze-thawing cycle of a population of spermatozoa selected by PureSperm, with retained motility and functional integrity. This points to the possibility of using double frozen spermatozoa in bovine artificial insemination programmes and to the potential benefits of PureSperm density gradient centrifugation for the application of cryopreserved bull spermatozoa to other biotechnological procedures such as flow cytometric sex sorting followed by re-freezing and thawing.

Conserved and narrow temperature limits in alpine insects: Thermal tolerance and supercooling points of the ice-crawlers, Grylloblatta (Insecta: Grylloblattodea: Grylloblattidae).

PubMed

Schoville, Sean D; Slatyer, Rachel A; Bergdahl, James C; Valdez, Glenda A

2015-07-01

For many terrestrial species, habitat associations and range size are dependent on physiological limits, which in turn may influence large-scale patterns of species diversity. The temperature range experienced by individuals is considered to shape the breadth of the thermal niche, with species occupying temporally and/or geographically stable climates tolerating a narrow temperature range. High-elevation environments experience large temperature fluctuations, with frequent periods below 0 °C, but Grylloblatta (Grylloblattodea: Grylloblattidae) occupy climatically stable microhabitats within this region. Here we test critical thermal limits and supercooling points for five Grylloblatta populations from across a large geographic area, to examine whether the stable microhabitats of this group are associated with a narrow thermal niche and assess their capacity to tolerate cold conditions. Thermal limits are highly conserved in Grylloblatta, despite substantial genetic divergence among populations spanning 1500 m elevation and being separated by over 500 km. Further, Grylloblatta show exceptionally narrow thermal limits compared to other insect taxa with little capacity to improve cold tolerance via plasticity. In contrast, upper thermal limits were significantly depressed by cold acclimation. Grylloblatta maintain coordinated movement until they freeze, and they die upon freezing. Convergence of the critical thermal minima, supercooling point and lower lethal limits point to adaptation to a cold but, importantly, constant thermal environment. These physiological data provide an explanation for the high endemism and patchy distribution of Grylloblatta, which relies on subterranean retreats to accommodate narrow thermal limits. These retreats are currently buffered from temperature fluctuations by snow cover, and a declining snowpack thus places Grylloblatta at risk of exposure to temperatures beyond its tolerance capacity. Copyright © 2015 Elsevier Ltd. All rights reserved.

Aquatic toxicity of airfield-pavement deicer materials and implications for airport runoff.

PubMed

Corsi, Steven R; Geis, Steven W; Bowman, George; Failey, Greg G; Rutter, Troy D

2009-01-01

Concentrations of airfield-pavement deicer materials (PDM) in a study of airport runoff often exceeded levels of concern regarding aquatic toxicity. Toxicity tests on Vibrio fischeri, Pimephales promelas, Ceriodaphnia dubia, and Pseudokirchneriella subcapitata (commonly known as Selenastrum capricornutum) were performed with potassium acetate (K-Ac) PDM, sodium formate (Na-For) PDM, and with freezing-point depressants (K-Ac and Na-For). Results indicate that toxicity in PDM is driven by the freezing-point depressants in all tests except the Vibrio fisheri test for Na-For PDM which is influenced by an additive. Acute toxicity end points for different organisms ranged from 298 to 6560 mg/L (as acetate) for K-Ac PDM and from 1780 to 4130 mg/L (as formate) for Na-For PDM. Chronic toxicity end points ranged from 19.9 to 336 mg/L (as acetate) for K-Ac PDM and from 584 to 1670 mg/L (as formate) for Na-For PDM. Sample results from outfalls at General Mitchell International Airport in Milwaukee, WI (GMIA) indicated that 40% of samples had concentrations greater thanthe aquatic-life benchmarkfor K-Ac PDM. K-Ac has replaced urea during the 1990s as the most widely used PDM at GMIA and in the United States. Results of ammonia samples from airport outfalls during periods when urea-based PDM was used at GMIA indicated that 41% of samples had concentrations exceeding the U.S. Environmental Protection Agency (USEPA) 1-h water-quality criterion. The USEPA 1-h water-quality criterion for chloride was exceeded in 68% of samples collected in the receiving stream, a result of road-salt runoff from urban influence near the airport. Results demonstrate that PDM must be considered to comprehensively evaluate the impact of chemical deicers on aquatic toxicity in water containing airport runoff.

Mechanisms of deterioration of nutrients. [of freeze dried foods

NASA Technical Reports Server (NTRS)

Karel, M.; Flink, J. M.

1976-01-01

Methods which produce freeze dried foods of improved quality were examined with emphasis on storage stability. Specific topics discussed include: microstructure of freeze dried systems, investigation of structural changes in freeze dried systems, artificial food matrices, osmotic preconcentration to yield improved quality freeze dried fruits, and storage stability of osmotically preconcentrated freeze dried fruits.

Effect of freeze/thaw cycles on several biomarkers in urine from patients with kidney disease.

PubMed

Zhang, Yinan; Luo, Yi; Lu, Huijuan; Wang, Niansong; Shen, Yixie; Chen, Ruihua; Fang, Pingyan; Yu, Hong; Wang, Congrong; Jia, Weiping

2015-04-01

Urine samples were collected from eleven randomly selected patients with kidney disease, including diabetic nephropathy, chronic nephritis, and nephritic syndrome. Urine samples were treated with one of four protocols for freezing and thawing: freeze directly and thaw directly; freeze directly and thaw by temperature gradient; freeze by temperature gradient and thaw directly; and freeze by temperature gradient and thaw by temperature gradient. After one to six freeze/thaw cycles at -20°C or -80°C, different biomarkers showed differential stabilities. The concentrations of total protein, calcium, and potassium did not change significantly after five freeze/thaw cycles at either -20°C or -80°C. Albumin could only sustain three freeze/thaw cycles at -20°C before it started to degrade. We recommend that urine be stored at -80°C as albumin and the organic ions could sustain five and six freeze/thaw cycles, respectively, using the simple "direct freeze and direct thaw" protocol. Furthermore, in most cases, gradient freeze/thaw cycles are not necessary for urine sample storage.

Stability Studies of a Freeze-Dried Recombinant Human Epidermal Growth Factor Formulation for Wound Healing.

PubMed

Santana, Héctor; García, Gerardo; Vega, Maribel; Beldarraín, Alejandro; Páez, Rolando

2015-01-01

We report on the stability assessment of a recombinant human epidermal growth factor (rhEGF) freeze-dried formulation for wound healing by intra-lesional injections. The suitability of packaging material for the light protection of finished dried powder was evaluated after stressed exposure conditions. Degradation kinetics of powder for injection was investigated at concentrations of 25-250 μg/vial and temperatures of 45, 60, and 70 °C. The long-term stability was evaluated after storage at 25 ± 2 °C/60 ± 5% relative humidity (6 months) and 2-8 °C (24 months) in the dark and analyzed at several time points. The stability after reconstitution with various diluents was also assessed after 24 h storage at 2-8 °C. The rhEGF samples were analyzed for structural integrity by reversed-phase high-performance liquid chromatography (RP-HPLC), size-exclusion HPLC, and sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). Biological activity was investigated by measuring the cell proliferation in a murine fibroblast cell line. Results show that freeze-dried rhEGF in primary packaging only was photosensitive, as degradation by RP-HPLC that was completely suppressed by the secondary carton package was revealed. An increase in freeze-dried rhEGF stability was observed with the increase in protein concentration from 25 to 250 μg/vial. The long-term stability study showed no significant rhEGF degradation or physical change within the freeze-dried formulations containing 25 or 250 μg/vial of rhEGF. No physical, chemical or biological changes were observed for rhEGF after reconstitution in water for injection or 0.9% sodium chloride during the storage conditions studied. The stability of a recombinant human epidermal growth factor (rhEGF) freeze-dried formulation for wound healing by intra-lesional injections was assessed. The suitability of packaging material for the light protection of finished dried powder was evaluated after stressed exposure conditions. Degradation kinetics of powder for injection was investigated at concentrations of 25-250 μg/vial and temperatures of 45, 60, and 70 °C. The accelerated, long-term, and reconstitution stabilities were examined according to ICH guidelines for their utility time. The stability of rhEGF samples was analyzed by different chemical, physical, and biological activity assays. Results show that freeze-dried rhEGF in primary packaging only was photosensitive, as degradation by reversed-phase high performance liquid chromatography that was completely suppressed by the secondary carton package was revealed. An increase in freeze-dried rhEGF stability was observed with the increase in protein concentration. No significant rhEGF degradation or physical changes were observed within the freeze-dried formulations after 6 months storage at 25 ± 2 °C/60 ± 5% relative humidity or 24 months storage at 2-8 °C. No physical, chemical, or biological changes were observed for rhEGF after reconstitution in water for injection or 0.9% sodium chloride after 24 h storage at 2-8 °C. © PDA, Inc. 2015.

Assessing storage of stability and mercury reduction of freeze-dried Pseudomonas putida within different types of lyoprotectant

NASA Astrophysics Data System (ADS)

Azoddein, Abdul Aziz Mohd; Nuratri, Yana; Azli, Faten Ahada Mohd; Bustary, Ahmad Bazli

2017-12-01

Pseudomonas putida is a potential strain in biological treatment to remove mercury contained in the effluent of petrochemical industry due to its mercury reductase enzyme that able to reduce ionic mercury to elementary mercury. Freeze-dried P. putida allows easy, inexpensive shipping, handling and high stability of the product. This study was aimed to freeze dry P. putida cells with addition of lyoprotectant. Lyoprotectant was added into the cells suspension prior to freezing. Dried P. putida obtained was then mixed with synthetic mercury. Viability of recovery P. putida after freeze dry was significantly influenced by the type of lyoprotectant. Among the lyoprotectants, tween 80/ sucrose was found to be the best lyoprotectant. Sucrose was able to recover more than 78% (6.2E+09 CFU/ml) of the original cells (7.90E+09CFU/ml) after freeze dry and able to retain 5.40E+05 viable cells after 4 weeks storage at 4 °C without vacuum. Polyethylene glycol (PEG) pre-treated freeze dried cells and broth pre-treated freeze dried cells after the freeze-dry process recovered more than 64% (5.0 E+09CFU/ml) and >0.1% (5.60E+07CFU/ml). Freeze-dried P. putida cells in PEG and broth cannot survive after 4 weeks storage. Freeze dry also does not really change the pattern of growth P. putida but extension of lag time was found 1 hour after 3 weeks of storage. Additional time was required for freeze-dried P. putida cells to recover before introducing freeze-dried cells to more complicated condition such as mercury solution. The maximum mercury reduction of PEG pre-treated freeze-dried cells after freeze dry and after storage of 3 weeks was 17.91 %. The maximum of mercury reduction of tween 80/sucrose pre-treated freeze-dried cells after freeze dry and after storage 3 weeks was 25.03%. Freeze dried P. putida was found to have lower mercury reduction compare to the fresh P. putida that has been grown in agar. Result from this study may be beneficial and useful as initial reference before commercialized freeze-dried P. putida.

Modular control subsystems for use in solar heating systems for multi-family dwellings

NASA Technical Reports Server (NTRS)

1977-01-01

Progress in the development of solar heating modular control subsystems is reported. Circuit design, circuit drawings, and printed circuit board layout are discussed along with maintenance manuals, installation instructions, and verification and acceptance tests. Calculations made to determine the predicted performance of the differential thermostat are given including details and results of tests for the offset temperature, and boil and freeze protect points.

Induction of cold hardiness in an invasive herbivore: The case of hemlock woolly adelgid (Hemiptera: Adelgidae)

Treesearch

Joseph S. Elkinton; Jeffrey A. Lombardo; Artemis D. Roehrig; Thomas J. McAvoy; Albert Mayfield; Mark Whitmore

2017-01-01

As a measure of cold hardiness, we tested the supercooling points or freezing temperatures of individual hemlock woolly adelgids (Adelges tsugae Annand) collected from 15 locations across the north to south range of the adelgid in eastern North America at different times during two winters. Adelgids from the northern interior locations with USDA hardiness zones of 5B–...

Enthalpy measurement of coal-derived liquids. Technical progress report, August-October 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kidnay, A.J.; Yesavage, V.F.

The correlational effort on the coal syncrudes and model compounds has been proceeding along two fronts. The first involves experimental work on a correlating factor for association in the liquids and the second involves an investigation of the modeling capabilities of cubic equations of state. The first area of investigation is the experimental measurement of a correlating factor for assocition in coal liquids. The procedure involves molecular weight measurement by freezing point depression. To facilitate these measurements, a simple Beckman freezing point depression apparatus is being currently modified to increase the accuracy, speed, and ease of measurement. The second areamore » of effort has involved establishing a set of cubic equations of state which can adequately model the enthalpy departures of quinoline and m-cresol. To this effort, a number of standard and association specific equations of state have been tested against a data base of previously measured enthalpy departures of m-cresol and quinoline. It has been found that these equations do quantitatively a poor job on m-cresol and quinoline. These problems are probably due to the highly polar nature of m-cresol and to a lesser extent quinoline, and to the poor quality of critical parameters for quinoline.« less

Study on Latent Heat of Fusion of Ice in Aqueous Solutions

NASA Astrophysics Data System (ADS)

Kumano, Hiroyuki; Asaoka, Tatsunori; Saito, Akio; Okawa, Seiji

In this study, latent heat of fusion of ice in aqueous solutions was measured to understand latent heat of fusion of ice slurries. Propylene glycol, ethylene glycol, ethanol, NaCl and NaNO3 solutions were examined as the aqueous solutions. In the measurement, pure ice was put into the solution, and the temperature variation of the solution due to the melting of the ice was measured. Then, the effective latent heat of fusion was calculated from energy balance equation. When ice melts in solution, the concentration of the solution varies due to the melting of the ice, and dilution heat must be considered. Therefore, the latent heat of fusion of ice in aqueous solutions was predicted by considering the effects of dilution and freezing-point depression. The latent heat of fusion was also measured by differential scanning calorimetry(DSC) to compare the results obtained from the experiments with that obtained by DSC. As the result, it was found that the effective latent heat of fusion of ice decreased with the increase of the concentration of solution, and the effective latent heat of fusion was calculated from latent heat of fusion of pure ice and the effects of freezing-point depression and the dilution heat.

Rubber closures for freeze-dried products.

PubMed

Hopkins, G H

1976-10-01

Once a biological product has been developed to perform its required medical or pharmaceutical function, it is essential that a container-closure system by chosen which will preserve the efficacy of the product up to the point of administration. The general requirements applicable to proper closure function will be reviewed and the suitability of natural and synthetic elastomers to perform these functions will be discussed. The specialized application of elastomeric materials as closures for freeze-dried products presents additional requirements which are superimposed upon those previously discussed. The first of these unique considerations relates to the proper physical design which will permit the outgassing of water vapor during the sublimation step in the lyophilizing chamber. During this outgassing the design must also permit the closure to remain affixed in the neck while only partially inserted. Since these preparations are lyophilized because they are unstable in aqueous solutions, the elastomer used must constitute an effective barrier to the transmission of moisture vapor through the closure. The MVT and gas transmission properties of elastomers will be discussed. Special consideration will be given to the extremely low temperatures used in the sublimation, stoppering, and storage before use of lyophilized products. The phenomenon of glass transition points with different elastomers will be explained as its relation to satisfactory performance of the closure function at low temperatures.

[Physico-chemical and microbiological evaluation of UHT milk commercialized in three Mercosul countries (Brazil, Argentina and Paraguay)].

PubMed

Domareski, Jackson Luiz; Bandiera, Nataly Simões; Sato, Rafael Tamostu; Aragon-Alegro, Lina Casale; de Santana, Elsa Helena Walter

2010-09-01

With the aim to evaluate the physico-chemical and microbiological quality of UHT milk commercialized in three countries of Mercosul, samples of four different brands were acquired in each city (Foz do Iguaçu-Brazil, Puerto Iguazú-Argentina and Ciudad del Este-Paraguay) and submitted to the following analysis: fat content, titratable acidity, milk ethanol stability (with the following ethanol concentrations: 68, 72, 76 and 80%), total dry extract and no fat dry extract, pH, density and freezing point. Counts of mesophilic and psychrotrophic microorganisms were already done. In the physico-chemical evaluation of UHT milk, a significant number of samples were in disagree with the established patterns for fat content, no fat dry extract, density and freezing point. Except one brand from Brazil, milk samples showed stability to 68% ethanol. pH averages of Brazilian milk were in agree with the patterns and highest values were observed in samples acquired on Paraguay. Observing the microbiological analysis, 37.5%, 62.5% and 12.5% of samples acquired from Brazil, Argentina and Paraguay, respectively, showed counts above the established patterns for mesophilic microorganisms. Counts of psychrotrophic microorganisms were in disagree with the established patterns in 50%, 50% and 100% of samples from Brazil, Argentina and Paraguay, respectively.

Perturbation of bacterial ice nucleation activity by a grass antifreeze protein.

PubMed

Tomalty, Heather E; Walker, Virginia K

2014-09-26

Certain plant-associating bacteria produce ice nucleation proteins (INPs) which allow the crystallization of water at high subzero temperatures. Many of these microbes are considered plant pathogens since the formed ice can damage tissues, allowing access to nutrients. Intriguingly, certain plants that host these bacteria synthesize antifreeze proteins (AFPs). Once freezing has occurred, plant AFPs likely function to inhibit the growth of large damaging ice crystals. However, we postulated that such AFPs might also serve as defensive mechanisms against bacterial-mediated ice nucleation. Recombinant AFP derived from the perennial ryegrass Lolium perenne (LpAFP) was combined with INP preparations originating from the grass epiphyte, Pseudomonas syringae. The presence of INPs had no effect on AFP activity, including thermal hysteresis and ice recrystallization inhibition. Strikingly, the ice nucleation point of the INP was depressed up to 1.9°C in the presence of LpAFP, but a recombinant fish AFP did not lower the INP-imposed freezing point. Assays with mutant LpAFPs and the visualization of bacterially-displayed fluorescent plant AFP suggest that INP and LpAFP can interact. Thus, we postulate that in addition to controlling ice growth, plant AFPs may also function as a defensive strategy against the damaging effects of ice-nucleating bacteria. Crown Copyright © 2014. Published by Elsevier Inc. All rights reserved.

Using Power Ultrasound to Accelerate Food Freezing Processes: Effects on Freezing Efficiency and Food Microstructure.

PubMed

Zhang, Peizhi; Zhu, Zhiwei; Sun, Da-Wen

2018-05-31

Freezing is an effective way of food preservation. However, traditional freezing methods have the disadvantages of low freezing efficiency and generation of large ice crystals, leading to possible damage of food quality. Power ultrasound assisted freezing as a novel technique can effectively reduce the adverse effects during freezing process. This paper gives an overview on recent researches of power ultrasound technique to accelerate the food freezing processes and illustrates the main principles of power ultrasound assisted freezing. The effects of power ultrasound on liquid food, model solid food as well as fruit and vegetables are discussed, respectively, from the aspects of increasing freezing rate and improving microstructure. It is shown that ultrasound assisted freezing can effectively improve the freezing efficiency and promote the formation of small and evenly distributed ice crystals, resulting in better food quality. Different inherent properties of food samples affect the effectiveness of ultrasound application and optimum ultrasound parameters depend on the nature of the samples. The application of ultrasound to the food industry is more likely on certain types of food products and more efforts are still needed to realize the industrial translation of laboratory results.

Spatial Variation of Pressure in the Lyophilization Product Chamber Part 2: Experimental Measurements and Implications for Scale-up and Batch Uniformity.

PubMed

Sane, Pooja; Varma, Nikhil; Ganguly, Arnab; Pikal, Michael; Alexeenko, Alina; Bogner, Robin H

2017-02-01

Product temperature during the primary drying step of freeze-drying is controlled by a set point chamber pressure and shelf temperature. However, recent computational modeling suggests a possible variation in local chamber pressure. The current work presents an experimental verification of the local chamber pressure gradients in a lab-scale freeze-dryer. Pressure differences between the center and the edges of a lab-scale freeze-dryer shelf were measured as a function of sublimation flux and clearance between the sublimation front and the shelf above. A modest 3-mTorr difference in pressure was observed as the sublimation flux was doubled from 0.5 to 1.0 kg·h -1 ·m -2 at a clearance of 2.6 cm. Further, at a constant sublimation flux of 1.0 kg·h -1 ·m -2 , an 8-fold increase in the pressure drop was observed across the shelf as the clearance was decreased from 4 to 1.6 cm. Scale-up of the pressure variation from lab- to a manufacturing-scale freeze-dryer predicted an increased uniformity in drying rates across the batch for two frequently used pharmaceutical excipients (mannitol and sucrose at 5% w/w). However, at an atypical condition of shelf temperature of +10°C and chamber pressure of 50 mTorr, the product temperature in the center vials was calculated to be a degree higher than the edge vial for a low resistance product, thus reversing the typical edge and center vial behavior. Thus, the effect of local pressure variation is more significant at the manufacturing-scale than at a lab-scale and accounting for the contribution of variations in the local chamber pressures can improve success in scale-up.

Brinicles as a case of inverse chemical gardens.

PubMed

Cartwright, Julyan H E; Escribano, Bruno; González, Diego L; Sainz-Díaz, C Ignacio; Tuval, Idan

2013-06-25

Brinicles are hollow tubes of ice from centimeters to meters in length that form under floating sea ice in the polar oceans when dense, cold brine drains downward from sea ice to seawater close to its freezing point. When this extremely cold brine leaves the ice, it freezes the water it comes into contact with: a hollow tube of ice-a brinicle-growing downward around the plume of descending brine. We show that brinicles can be understood as a form of the self-assembled tubular precipitation structures termed chemical gardens, which are plantlike structures formed on placing together a soluble metal salt, often in the form of a seed crystal, and an aqueous solution of one of many anions, often silicate. On one hand, in the case of classical chemical gardens, an osmotic pressure difference across a semipermeable precipitation membrane that filters solutions by rejecting the solute leads to an inflow of water and to its rupture. The internal solution, generally being lighter than the external solution, flows up through the break, and as it does so, a tube grows upward by precipitation around the jet of internal solution. Such chemical-garden tubes can grow to many centimeters in length. In the case of brinicles, on the other hand, in floating sea ice we have porous ice in a mushy layer that filters out water, by freezing it, and allows concentrated brine through. Again there is an osmotic pressure difference leading to a continuing ingress of seawater in a siphon pump mechanism that is sustained as long as the ice continues to freeze. Because the brine that is pumped out is denser than the seawater and descends rather than rises, a brinicle is a downward-growing tube of ice, an inverse chemical garden.

Effect of Microgravity on Material Undergoing Melting and Freezing: the TES Experiment

NASA Technical Reports Server (NTRS)

Namkoong, David; Jacqmin, David; Szaniszlo, Andrew

1995-01-01

This experiment is the first to melt and freeze a high temperature thermal energy storage (TES) material under an extended duration of microgravity. It is one of a series to validate an analytical computer program that predicts void behavior of substances undergoing phase change under microgravity. Two flight experiments were launched in STS-62. The first, TES-1, containing lithium fluoride in an annular volume, performed flawlessly in the 22 hours of its operation. Results are reported in this paper. A software failure in TES-2 caused its shutdown after 4 seconds. A computer program, TESSIM, for thermal energy storage simulation is being developed to analyze the phenomena occurring within the TES containment vessel. The first order effects, particularly the surface tension forces, have been incorporated into TESSIM. TESSIM validation is based on two types of results. First is the temperature history of various points of the containment structure, and second, upon return from flight, the distribution of the TES material within the containment vessel following the last freeze cycle. The temperature data over the four cycles showed a repetition of results over the third and fourth cycles. This result is a confirmation that any initial conditions prior to the first cycle had been damped out by the third cycle. The TESSIM simulation showed a close comparison with the flight data. The solidified TES material distribution within the containment vessel was obtained by a tomography imaging process. The frozen material was concentrated toward the colder end of the annular volume. The TESSIM prediction showed the same pattern. With the general agreement of TESSIM and the data, a computerized visual representation can be shown which accurately shows the movement and behavior of the void during the entire freezing and melting cycles.

Effect of microgravity on material undergoing melting and freezing: The TES Experiment

NASA Astrophysics Data System (ADS)

Namkoong, David; Jacqmin, David; Szaniszlo, Andrew

1995-01-01

This experiment is the first to melt and freeze a high temperature thermal energy storage (TES) material under an extended duration of microgravity. It is one of a series to validate an analytical computer program that predicts void behavior of substances undergoing phase change under microgravity. Two flight experiments were launched in STS-62. The first, TES-1, containing lithium fluoride in an annular volume, performed flawlessly in the 22 hours of its operation. Results are reported in this paper. A software failure in TES-2 caused its shutdown after 4 seconds. A computer program, TESSIM, for thermal energy storage simulation is being developed to analyze the phenomena occurring within the TES containment vessel. The first order effects, particularly the surface tension forces, have been incorporated into TESSIM. TESSIM validation is based on two types of results. First is the temperature history of various points of the containment structure, and second, upon return from flight, the distribution of the TES material within the containment vessel following the last freeze cycle. The temperature data over the four cycles showed a repetition of results over the third and fourth cycles. This result is a confirmation that any initial conditions prior to the first cycle had been damped out by the third cycle. The TESSIM simulation showed a close comparison with the flight data. The solidified TES material distribution within the containment vessel was obtained by a tomography imaging process. The frozen material was concentrated toward the colder end of the annular volume. The TESSIM prediction showed the same pattern. With the general agreement of TESSIM and the data, a computerized visual representation can be shown which accurately shows the movement and behavior of the void during the entire freezing and melting cycles.

Presumption of large-scale heterogeneity at the top of the outer core basal layer

NASA Astrophysics Data System (ADS)

Souriau, Annie

2015-04-01

A layer of reduced P-velocity gradient with thickness of about 100-200 km has been identified at the base of the liquid core from seismological methods. It has been interpreted as a dense layer resulting from partial re-melting of the inner core, which is depleted in light elements with respect to the liquid core during freezing. In an attempt to specify where freezing and re-melting occur, the structure of this basal layer is investigated with the seismological core phase PKPbc which has its turning point in the lower third of the outer core. The large PKPbc data set of the EHB catalog distributed by the International Seismological Centre is analyzed. In order to compensate for the uneven distribution of the data and to minimize the influence of mantle heterogeneities, the travel time anomalies are binned inside equal area and equal azimuth sectors sampling the base of the liquid core at different depths. Most of the observed variations in the binned travel time residuals are not significant according to their confidence level. The only features which could be significant are a large patch with a velocity increase of about 0.5% located at the top of the basal layer beneath the eastern hemisphere, and the complementary velocity decrease beneath the western hemisphere and the South pole. This observation suggests that some freezing or re-melting processes occur at the top of the basal layer with a hemispherical dissymmetry. If confirmed, it may give strong constraints on the fate of the light elements during the freezing and re-melting process and on their interaction with the basal layer and the overlying liquid core.

A quantitative evaluation of two methods for preserving hair samples

USGS Publications Warehouse

Roon, David A.; Waits, L.P.; Kendall, K.C.

2003-01-01

Hair samples are an increasingly important DNA source for wildlife studies, yet optimal storage methods and DNA degradation rates have not been rigorously evaluated. We tested amplification success rates over a one-year storage period for DNA extracted from brown bear (Ursus arctos) hair samples preserved using silica desiccation and -20C freezing. For three nuclear DNA microsatellites, success rates decreased significantly after a six-month time point, regardless of storage method. For a 1000 bp mitochondrial fragment, a similar decrease occurred after a two-week time point. Minimizing delays between collection and DNA extraction will maximize success rates for hair-based noninvasive genetic sampling projects.

Exploration of Impinging Water Spray Heat Transfer at System Pressures Near the Triple Point

NASA Technical Reports Server (NTRS)

Golliher, Eric L.; Yao, Shi-Chune

2013-01-01

The heat transfer of a water spray impinging upon a surface in a very low pressure environment is of interest to cooling of space vehicles during launch and re-entry, and to industrial processes where flash evaporation occurs. At very low pressure, the process occurs near the triple point of water, and there exists a transient multiphase transport problem of ice, water and water vapor. At the impingement location, there are three heat transfer mechanisms: evaporation, freezing and sublimation. A preliminary heat transfer model was developed to explore the interaction of these mechanisms at the surface and within the spray.

Trends of jet fuel demand and properties

NASA Technical Reports Server (NTRS)

Friedman, R.

1984-01-01

Petroleum industry forecasts predict an increasing demand for jet fuels, a decrease in the gasoline-to-distillate (heavier fuel) demand ratio, and a greater influx of poorer quality petroleum in the next two to three decades. These projections are important for refinery product analyses. The forecasts have not been accurate, however, in predicting the recent, short term fluctuations in jet fuel and competing product demand. Changes in petroleum quality can be assessed, in part, by a review of jet fuel property inspections. Surveys covering the last 10 years show that average jet fuel freezing points, aromatic contents, and smoke points have trends toward their specification limits.

Concrete/mortar water phase transition studied by single-point MRI methods.

PubMed

Prado, P J; Balcom, B J; Beyea, S D; Armstrong, R L; Bremner, T W; Grattan-Bellew, P E

1998-01-01

A series of magnetic resonance imaging (MRI) water density and T2* profiles in hardened concrete and mortar samples has been obtained during freezing conditions (-50 degrees C < T < 11 degrees C). The single-point ramped imaging with T1 enhancement (SPRITE) sequence is optimal for this study given the characteristic short relaxation times of water in this porous media (T2* < 200 microseconds and T1 < 3.6 ms). The frozen and evaporable water distribution was quantified through a position based study of the profile magnitude. Submillimetric resolution of proton-density and T2*-relaxation parameters as a function of temperature has been achieved.

Alternative aviation turbine fuels

NASA Technical Reports Server (NTRS)

Grobman, J.

1977-01-01

The efficient utilization of fossil fuels by future jet aircraft may necessitate the broadening of current aviation turbine fuel specifications. The most significant changes in specifications would be an increased aromatics content and a higher final boiling point in order to minimize refinery energy consumption and costs. These changes would increase the freezing point and might lower the thermal stability of the fuel and could cause increased pollutant emissions, increased smoke and carbon formation, increased combustor liner temperatures, and poorer ignition characteristics. This paper discusses the effects that broadened specification fuels may have on present-day jet aircraft and engine components and the technology required to use fuels with broadened specifications.

A comparison of freezing-damage during isochoric and isobaric freezing of the potato.

PubMed

Lyu, Chenang; Nastase, Gabriel; Ukpai, Gideon; Serban, Alexandru; Rubinsky, Boris

2017-01-01

Freezing is commonly used for food preservation. It is usually done under constant atmospheric pressure (isobaric). While extending the life of the produce, isobaric freezing has detrimental effects. It causes loss of food weight and changes in food quality. Using thermodynamic analysis, we have developed a theoretical model of the process of freezing in a constant volume system (isochoric). The mathematical model suggests that the detrimental effects associated with isobaric freezing may be reduced in an isochoric freezing system. To explore this hypothesis, we performed a preliminary study on the isochoric freezing of a produce with which our group has experience, the potato. Experiments were performed in an isochoric freezing device we designed. The device is robust and has no moving parts. For comparison, we used a geometrically identical isobaric freezing device. Following freezing and thawing, the samples were weighed, examined with colorimetry, and examined with microscopy. It was found that potatoes frozen to -5 °C in an isochoric system experienced no weight loss and limited enzymatic browning. In contrast the -5 °C isobaric frozen potato experienced substantial weight loss and substantial enzymatic browning. Microscopic analysis shows that the structural integrity of the potato is maintained after freezing in the isochoric system and impaired after freezing in the isobaric system. Tissue damage during isobaric freezing is caused by the increase in extracellular osmolality and the mechanical damage by ice crystals. Our thermodynamic analysis predicts that during isochoric freezing the intracellular osmolality remains comparable to the extracellular osmolality and that isochoric systems can be designed to eliminate the mechanical damage by ice. The results of this preliminary study seem to confirm the theoretical predictions. This is a preliminary exploratory study on isochoric freezing of food. We have shown that the quality of a food product preserved by isochoric freezing is better than the quality of food preserved to the same temperature in isobaric conditions. Obviously, more extensive research remains to be done to extend this study to lower freezing temperatures and other food items.

A comparison of freezing-damage during isochoric and isobaric freezing of the potato

PubMed Central

Serban, Alexandru; Rubinsky, Boris

2017-01-01

Background Freezing is commonly used for food preservation. It is usually done under constant atmospheric pressure (isobaric). While extending the life of the produce, isobaric freezing has detrimental effects. It causes loss of food weight and changes in food quality. Using thermodynamic analysis, we have developed a theoretical model of the process of freezing in a constant volume system (isochoric). The mathematical model suggests that the detrimental effects associated with isobaric freezing may be reduced in an isochoric freezing system. To explore this hypothesis, we performed a preliminary study on the isochoric freezing of a produce with which our group has experience, the potato. Method Experiments were performed in an isochoric freezing device we designed. The device is robust and has no moving parts. For comparison, we used a geometrically identical isobaric freezing device. Following freezing and thawing, the samples were weighed, examined with colorimetry, and examined with microscopy. Results It was found that potatoes frozen to −5 °C in an isochoric system experienced no weight loss and limited enzymatic browning. In contrast the −5 °C isobaric frozen potato experienced substantial weight loss and substantial enzymatic browning. Microscopic analysis shows that the structural integrity of the potato is maintained after freezing in the isochoric system and impaired after freezing in the isobaric system. Discussion Tissue damage during isobaric freezing is caused by the increase in extracellular osmolality and the mechanical damage by ice crystals. Our thermodynamic analysis predicts that during isochoric freezing the intracellular osmolality remains comparable to the extracellular osmolality and that isochoric systems can be designed to eliminate the mechanical damage by ice. The results of this preliminary study seem to confirm the theoretical predictions. Conclusion This is a preliminary exploratory study on isochoric freezing of food. We have shown that the quality of a food product preserved by isochoric freezing is better than the quality of food preserved to the same temperature in isobaric conditions. Obviously, more extensive research remains to be done to extend this study to lower freezing temperatures and other food items. PMID:28533970

Mechanisms of deterioration of nutrients. [improved quality of freeze-dried foods

NASA Technical Reports Server (NTRS)

Karel, M.; Flink, J. M.

1978-01-01

Methods for improving the quality of freeze-dried foods were investigated. Areas discussed include: (1) microstructure of freeze-dried systems, (2) structural changes in freeze-dried systems, (3) artificial food matrices, and (4) osmotic preconcentration to yield improved freeze-dried products.

Accurate prediction of collapse temperature using optical coherence tomography-based freeze-drying microscopy.

PubMed

Greco, Kristyn; Mujat, Mircea; Galbally-Kinney, Kristin L; Hammer, Daniel X; Ferguson, R Daniel; Iftimia, Nicusor; Mulhall, Phillip; Sharma, Puneet; Kessler, William J; Pikal, Michael J

2013-06-01

The objective of this study was to assess the feasibility of developing and applying a laboratory tool that can provide three-dimensional product structural information during freeze-drying and which can accurately characterize the collapse temperature (Tc ) of pharmaceutical formulations designed for freeze-drying. A single-vial freeze dryer coupled with optical coherence tomography freeze-drying microscopy (OCT-FDM) was developed to investigate the structure and Tc of formulations in pharmaceutically relevant products containers (i.e., freeze-drying in vials). OCT-FDM was used to measure the Tc and eutectic melt of three formulations in freeze-drying vials. The Tc as measured by OCT-FDM was found to be predictive of freeze-drying with a batch of vials in a conventional laboratory freeze dryer. The freeze-drying cycles developed using OCT-FDM data, as compared with traditional light transmission freeze-drying microscopy (LT-FDM), resulted in a significant reduction in primary drying time, which could result in a substantial reduction of manufacturing costs while maintaining product quality. OCT-FDM provides quantitative data to justify freeze-drying at temperatures higher than the Tc measured by LT-FDM and provides a reliable upper limit to setting a product temperature in primary drying. Copyright © 2013 Wiley Periodicals, Inc.

Freeze-drying of nanosuspensions, 1: freezing rate versus formulation design as critical factors to preserve the original particle size distribution.

PubMed

Beirowski, Jakob; Inghelbrecht, Sabine; Arien, Albertina; Gieseler, Henning

2011-05-01

It has been recently reported in the literature that using a fast freezing rate during freeze-drying of drug nanosuspensions is beneficial to preserve the original particle size distribution. All freezing rates studied were obtained by utilizing a custom-made apparatus and were then indirectly related to conventional vial freeze-drying. However, a standard freeze-dryer is only capable of achieving moderate freezing rates in the shelf fluid circulation system. Therefore, it was the purpose of the present study to evaluate the possibility to establish a typical freezing protocol applicable to a standard freeze-drying unit in combination with an adequate choice of cryoprotective excipients and steric stabilizers to preserve the original particle size distribution. Six different drug nanosuspensions containing itraconazole as a drug model were studied using freeze-thaw experiments and a full factorial design to reveal major factors for the stabilization of drug nanosuspensions and the corresponding interactions. In contrast to previous reports, the freezing regime showed no significant influence on preserving the original particle size distribution, suggesting that the concentrations of both the steric stabilizer and the cryoprotective agent are optimized. Moreover, it could be pinpointed that the combined effect of steric stabilizer and cryoprotectant clearly contribute to nanoparticle stability. Copyright © 2010 Wiley-Liss, Inc.

Freeze Technology for Nuclear Applications - 13590

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rostmark, Susanne C.; Knutsson, Sven; Lindberg, Maria

2013-07-01

Freezing of soil materials is a complicated process of a number of physical processes: - freezing of pore water in a thermal gradient, - cryogenic suction causing water migration and - ice formation expanding pores inducing frost heave. Structural changes due to increase of effective stress during freezing also take place. The over consolidation gives a powerful dewatering/drying effect and the freeze process causes separation of contaminates. Artificial ground freezing (AGF is a well established technique first practiced in south Wales, as early as 1862. AGF is mostly used to stabilize tunnels and excavations. During the last ten years underwatermore » applications of freeze technologies based on the AGF have been explored in Sweden. The technology can, and has been, used in many different steps in a remediation action. Freeze Sampling where undisturbed samples are removed in both soft and hard sediment/sludge, Freeze Dredging; retrieval of sediment with good precision and minimal redistribution, and Freeze Drying; volume reduction of contaminated sludge/sediment. The application of these technologies in a nuclear or radioactive environment provides several advantages. Sampling by freezing gives for example an advantage of an undisturbed sample taken at a specified depth, salvaging objects by freezing or removal of sludges is other applications of this, for the nuclear industry, novel technology. (authors)« less

Repeated freeze-thaw cycles induce embolism in drought stressed conifers (Norway spruce, stone pine).

PubMed

Mayr, Stefan; Gruber, Andreas; Bauer, Helmut

2003-07-01

Freezing and thawing lead to xylem embolism when gas bubbles caused by ice formation expand during the thaw process. However, previous experimental studies indicated that conifers are resistant to freezing-induced embolism, unless xylem pressure becomes very negative during the freezing. In this study, we show that conifers experienced freezing-induced embolism when exposed to repeated freeze-thaw cycles and simultaneously to drought. Simulating conditions at the alpine timberline (128 days with freeze-thaw events and thawing rates of up to 9.5 K h(-1) in the xylem of exposed twigs during winter), young trees of Norway spruce [Picea abies (L.) Karst.] and stone pine (Pinus cembra L.) were exposed to 50 and 100 freeze-thaw cycles. This treatment caused a significant increase in embolism rates in drought-stressed samples. Upon 100 freeze-thaw cycles, vulnerability thresholds (50% loss of conductivity) were shifted 1.8 MPa (Norway spruce) and 0.8 MPa (stone pine) towards less negative water potentials. The results demonstrate that freeze-thaw cycles are a possible reason for winter-embolism in conifers observed in several field studies. Freezing-induced embolism may contribute to the altitudinal limits of conifers.

Freezing of gait in Parkinson's disease: the paradoxical interplay between gait and cognition.

PubMed

Ricciardi, Lucia; Bloem, Bastiaan R; Snijders, Anke H; Daniele, Antonio; Quaranta, Davide; Bentivoglio, Anna Rita; Fasano, Alfonso

2014-08-01

Freezing of gait is a disabling episodic gait disturbance common in patients with Parkinson's disease. Recent evidences suggest a complex interplay between gait impairment and executive functions. Aim of our study was to evaluate whether specific motor conditions (sitting or walking) influence cognitive performance in patients with or without different types of freezing. Eight healthy controls, eight patients without freezing, nine patients with levodopa-responsive and nine patients with levodopa-resistant freezing received a clinical and neuropsychological assessment during two randomly performed conditions: at rest and during walking. At rest, patients with levodopa-resistant freezing performed worse than patients without freezing on tests of phonological fluency (p = 0.01). No differences among the four groups were detected during walking. When cognitive performances during walking were compared to the performance at rest, there was a significant decline of verbal episodic memory task (Rey Auditory Verbal Learning Test) in patients without freezing and with levodopa-responsive freezing. Interestingly, walking improved performance on the phonological fluency task in patients with levodopa-resistant freezing (p = 0.04). Compared to patients without freezing, patients with levodopa-resistant freezing perform worse when tested while seated in tasks of phonological verbal fluency. Surprisingly, gait was associated with a paradoxical improvement of phonological verbal fluency in the patients with levodopa-resistant freezing whilst walking determined a worsening of episodic memory in the other patient groups. Copyright © 2014 Elsevier Ltd. All rights reserved.

Freezing during tapping tasks in patients with advanced Parkinson's disease and freezing of gait.

PubMed

Delval, Arnaud; Defebvre, Luc; Tard, Céline

2017-01-01

Parkinson's disease patients with freezing of gait also experience sudden motor blocks (freezing) during other repetitive motor tasks. We assessed the proportion of patients with advanced PD and freezing of gait who also displayed segmental "freezing" in tapping tasks. Fifteen Parkinson's disease patients with freezing of gait were assessed. Freezing of gait was evaluated using a standardized gait trajectory with the usual triggers. Patients performed repetitive tapping movements (as described in the MDS-UPDRS task) with the hands or the feet in the presence or absence of a metronome set to 4 Hz. Movements were recorded with a video motion system. The primary endpoint was the occurrence of segmental freezing in these tapping tasks. The secondary endpoints were (i) the relationship between segmental episodic phenomena and FoG severity, and (ii) the reliability of the measurements. For the upper limbs, freezing was observed more frequently with a metronome (21% of trials) than without a metronome (5%). For the lower limbs, the incidence of freezing was higher than for the upper limbs, and was again observed more frequently in the presence of an auditory cue (47%) than in its absence (14%). Although freezing of the lower limbs was easily assessed during an MDS-UPDRS task with a metronome, it was not correlated with the severity of freezing of gait (as evaluated during a standardized gait trajectory). Only this latter was a reliable measurement in patients with advanced Parkinson's disease.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Monnai, Akihiko; Mukherjee, Swagato; Yin, Yi

In the proximity of the QCD critical point the bulk viscosity of quark-gluon matter is expected to be proportional to nearly the third power of the critical correlation length, and become significantly enhanced. Here, this work is the first attempt to study the phenomenological consequences of enhanced bulk viscosity near the QCD critical point. For this purpose, we implement the expected critical behavior of the bulk viscosity within a non-boost-invariant, longitudinally expanding 1 + 1 dimensional causal relativistic hydrodynamical evolution at nonzero baryon density. We demonstrate that the critically enhanced bulk viscosity induces a substantial nonequilibrium pressure, effectively softening themore » equation of state, and leads to sizable effects in the flow velocity and single-particle distributions at the freeze-out. In conclusion, the observable effects that may arise due to the enhanced bulk viscosity in the vicinity of the QCD critical point can be used as complementary information to facilitate searches for the QCD critical point.« less

Solvent-free synthesis of C10 and C11 branched alkanes from furfural and methyl isobutyl ketone.

PubMed

Yang, Jinfan; Li, Ning; Li, Guangyi; Wang, Wentao; Wang, Aiqin; Wang, Xiaodong; Cong, Yu; Zhang, Tao

2013-07-01

Our best results jet: C10 and C11 branched alkanes, with low freezing points, are synthesized through the aldol condensation of furfural and methyl isobutyl ketone from lignocellulose, which is then followed by hydrodeoxygenation. These jet-fuel-range alkanes are obtained in high overall yields (≈90%) under solvent-free conditions. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of jet fuel range branched cycloalkanes with mesityl oxide and 2-methylfuran from lignocellulose

NASA Astrophysics Data System (ADS)

Li, Shanshan; Li, Ning; Wang, Wentao; Li, Lin; Wang, Aiqin; Wang, Xiaodong; Zhang, Tao

2016-09-01

Jet fuel range branched cycloalkanes with high density (0.82 g mL-1) and low freezing point (217-219 K) was first prepared by the solvent-free intramolecular aldol condensation of the trione from the hydrolysis of the alkylation product of mesityl oxide and 2-methylfuran (or the one-pot reaction of mesityl oxide, 2-methylfuran and water), followed by hydrodeoxygenation (HDO).

Synthesis of jet fuel range branched cycloalkanes with mesityl oxide and 2-methylfuran from lignocellulose.

PubMed

Li, Shanshan; Li, Ning; Wang, Wentao; Li, Lin; Wang, Aiqin; Wang, Xiaodong; Zhang, Tao

2016-09-01

Jet fuel range branched cycloalkanes with high density (0.82 g mL(-1)) and low freezing point (217-219 K) was first prepared by the solvent-free intramolecular aldol condensation of the trione from the hydrolysis of the alkylation product of mesityl oxide and 2-methylfuran (or the one-pot reaction of mesityl oxide, 2-methylfuran and water), followed by hydrodeoxygenation (HDO).

Synthesis of jet fuel range branched cycloalkanes with mesityl oxide and 2-methylfuran from lignocellulose

PubMed Central

Li, Shanshan; Li, Ning; Wang, Wentao; Li, Lin; Wang, Aiqin; Wang, Xiaodong; Zhang, Tao

2016-01-01

Jet fuel range branched cycloalkanes with high density (0.82 g mL−1) and low freezing point (217–219 K) was first prepared by the solvent-free intramolecular aldol condensation of the trione from the hydrolysis of the alkylation product of mesityl oxide and 2-methylfuran (or the one-pot reaction of mesityl oxide, 2-methylfuran and water), followed by hydrodeoxygenation (HDO). PMID:27582417

Bibliography on Cold Regions Science and Technology. Volume 40, Part 1, 1986

DTIC Science & Technology

1986-12-01

witer migration in an unaaturated frozen soil, morin clay, waa determined in horizontally cloaed »oil columns under linear temperature gradients...Peninsula At both ice fronts there is signiPcant tidal height energy in the first seven tidal species, indicating strong non- linear interaction, not all...dry soil weight, and increases with the increase in the molality linearly because of the linear freezing point depression. The curves of the

Short-term and practice effects of metronome pacing in Parkinson's disease patients with gait freezing while in the 'on' state: randomized single blind evaluation.

PubMed

Cubo, Esther; Leurgans, Sue; Goetz, Christopher G

2004-12-01

In a randomized single blind parallel study, we tested the efficacy of an auditory metronome on walking speed and freezing in Parkinson's disease (PD) patients with freezing gait impairment during their 'on' function. No pharmacological treatment is effective in managing 'on' freezing in PD. Like visual cues that can help overcome freezing, rhythmic auditory pacing may provide cues that help normalize walking pace and overcome freezing. Non-demented PD patients with freezing during their 'on' state walked under two conditions, in randomized order: unassisted walking and walking with the use of an audiocassette with a metronome recording. The walking trials were randomized and gait variables were rated from videotapes by a blinded evaluator. Outcome measures were total walking time (total trial time-total freezing time), which was considered the time over a course of specified length, freezing time, average freeze duration and number of freezes. All outcomes were averaged across trials for each person and then compared across conditions using Signed Rank tests. Twelve non-demented PD patients with a mean age of 65.8 +/- 11.2 years, and mean PD duration of 12.4 +/- 7.3 years were included. The use of the metronome slowed ambulation and increased the total walking time (P < 0.0005) only during the first visit, without affecting any freezing variable. In the nine patients who took the metronome recording home and used it daily for 1 week while walking, freezing remained unimproved. Though advocated in prior publications as a walking aid for PD patients, auditory metronome pacing slows walking and is not a beneficial intervention for freezing during their 'on' periods.

Freezing Injury in Onion Bulb Cells

PubMed Central

Palta, Jiwan P.; Levitt, Jacob; Stadelmann, Eduard J.

1977-01-01

Onion (Allium cepa L.) bulbs were subjected for 12 days to either a moderate freeze (−4 C) or a severe freeze (−11 C). They were then thawed slowly over ice. During 7 to 12 days following the thaw, the injury progressed with time in the severely frozen bulbs, but appeared completely repaired in the moderately frozen bulbs. This was shown by the following post-thawing changes. Infiltration of the intercellular spaces increased from 80 to 90% to 100% after the severe freeze, and decreased from 30 to 50% to zero after the moderate freeze. All of the cells were alive immediately after thawing whether the freeze was moderate or severe. Corresponding to the infiltration results 7 to 12 days later, many to most were dead following the severe freeze, all were alive following the moderate freeze. The conductivity of the effusate from pieces of bulb tissue increased after the severe freezing, and decreased after the moderate freezing. The concentration of K+, total solutes, and sugars in the effusate paralleled the conductivity changes. Neither the pH of the effusate nor the permeability of the cells (as long as cells were living) to water was changed following either the severe or the moderate freezes. Some treatments of the thawed tissue following the severe freeze halted the progress of injury. The above results indicate that the semipermeable properties of the cell are uninjured but that the ion and sugar transport mechanism is damaged by freezing. Most likely the primary injury is to the active transport mechanism involved in their transport. It must be concluded that the final injury following freezing and thawing cannot be evaluated from the degree of infiltration or the conductivity of the effusate immediately after thawing, since injury may progress or recede following the thawing. PMID:16660101

Glycerolipidome responses to freezing- and chilling-induced injuries: examples in Arabidopsis and rice.

PubMed

Zheng, Guowei; Li, Lixia; Li, Weiqi

2016-03-22

Glycerolipids are the principal constituent of cellular membranes; remodelling of glycerolipids plays important roles in temperature adaptation in plants. Temperate plants can endure freezing stress, but even chilling at above-zero temperatures can induce death in tropical species. However, little is known about the differences in glycerolipid response to low temperatures between chilling-sensitive and freezing-tolerant plants. Using ESI-MS/MS-based lipidomic analysis, we compared the glycerolipidome of chilling (4 and 10 °C)-treated rice with that of freezing (-6 and -12 °C)-treated Arabidopsis, both immediately after these low-temperature treatments and after a subsequent recovery culture period. Arabidopsis is a 16:3 plant that harbours both eukaryotic and prokaryotic-type lipid synthesis pathways, while rice is an 18:3 plant that harbours only the eukaryotic lipid synthesis pathway. Arabidopsis contains higher levels of galactolipids than rice and has a higher double bond index (DBI). Arabidopsis contains lower levels of high melting point phosphatidylglycerol (PG) molecules and has a lower average acyl chain length (ACL). Marked phospholipid degradation occurred during the recovery culture period of non-lethal chilling treated rice, but did not occur in non-lethal freezing treated Arabidopsis. Glycerolipids with larger head groups were synthesized more in Arabidopsis than in rice at sub-lethal low-temperatures. Levels of phosphatidic acid (PA) and phosphatidylinositol (PI) rose in both plants after low-temperature treatment. The DBI and ACL of total lipids did not change during low-temperature treatment. A higher DBI and a lower ACL could make the membranes of Arabidopsis more fluid at low temperatures. The ability to synthesize glycerolipids containing a larger head group may correlate with low-temperature tolerance. The low-temperature-induced increase of PA may play a dual role in plant responses to low temperatures: as a lipid signal that initiates tolerance responses, and as a structural molecule that, on extensive in large accumulation, could damage the integrity of membranes. Changes in ACL and DBI are responses of plants to long-term low temperature.

Evaluation of combined effects of ageing period and freezing rate on quality attributes of beef loins.

PubMed

Kim, Yuan H Brad; Liesse, Charlotte; Kemp, Robert; Balan, Prabhu

2015-12-01

The objective of our study was to evaluate the combined effects of ageing period and different freezing rates on meat quality attributes of beef loins. Pairs of loins (M. longissimus at 1 day post mortem) from 12 carcasses were divided into four equal portions and randomly assigned to four ageing/freezing treatments (aged only, frozen only, and 3 or 4 weeks ageing at -1.5°C then frozen). Two freezing methods (fast freezing by calcium chloride immersion or slow freezing by air freezer at -18°C) were applied to the loin sections. Fast freezing had no effect on shear force (P>0.05), but significantly improved the water-holding capacity of the aged/frozen loins by reducing purge and drip losses. Ageing-then-freezing significantly improved shear force values of loins compared to both the aged only and frozen only loins. These observations suggest that fast freezing will add more value to the aged/frozen/thawed meat by minimising the amount of water-loss due to the freezing/thawing process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effects of different freezing methods on calcium enriched papaya (Carica papaya L.).

PubMed

Lovera, Nancy N; Ramallo, Laura; Salvadori, Viviana O

2018-06-01

The effect of calcium impregnation on drip loss, colour, mechanical properties, sensory perception and freezing time on frozen-thawed papaya was studied, evaluating different freezing methods: cryogenic, tunnel and household freezer freezing. Osmotic dehydration as pre-treatment was also evaluated. Freezing in liquid nitrogen was considered an inappropriate method for papaya preservation due to cracking. Calcium impregnation and osmotic dehydration increased tissue firmness and decreased freezing time (freezing time for fresh, calcium impregnated and osmo-dehydrated fruit was 23, 17 and 5 min in a tunnel and 118, 83 and 60 min in a household freezer, respectively). Calcium lactate was the most effective way to protect tissue's firmness before and after a freeze-thaw cycle (maximum stress values approx. 300-400% of the raw tissue for tunnel freezing and 260% for household freezer). Microstructure analysis showed better tissue integrity retention in papaya samples impregnated with calcium lactate than in those with calcium gluconate, after a freezing-thawing cycle, in agreement with the drip loss results. In spite of these results, consumers preferred frozen papaya without pre-treatment or impregnated with calcium gluconate.

Response of shoal grass, Halodule wrightii, to extreme winter conditions in the Lower Laguna Madre, Texas

USGS Publications Warehouse

Hicks, D.W.; Onuf, C.P.; Tunnell, J.W.

1998-01-01

Effects of a severe freeze on the shoal grass, Halodule wrightii, were documented through analysis of temporal and spatial trends in below-ground biomass. The coincidence of the second lowest temperature (-10.6??C) in 107 years of record, 56 consecutive hours below freezing, high winds and extremely low water levels exposed the Laguna Madre, TX, to the most severe cold stress in over a century. H. wrightii tolerated this extreme freeze event. Annual pre- and post-freeze surveys indicated that below-ground biomass estimated from volume was Unaffected by the freeze event. Nor was there any post-freeze change in biomass among intertidal sites directly exposed to freezing air temperatures relative to subtidal sites which remained submerged during the freezing period.

The effect of undissolved air on isochoric freezing.

PubMed

Perez, Pedro A; Preciado, Jessica; Carlson, Gary; DeLonzor, Russ; Rubinsky, Boris

2016-06-01

This study evaluates the effect of undissolved air on isochoric freezing of aqueous solutions. Isochoric freezing is concerned with freezing in a constant volume thermodynamic system. A possible advantage of the process is that it substantially reduces the percentage of ice in the system at every subzero temperature, relative to atmospheric freezing. At the pressures generated by isochoric freezing, or high pressure isobaric freezing, air cannot be considered an incompressible substance and the presence of undissolved air substantially increases the amount of ice that forms at any subfreezing temperature. This effect is measurable at air volumes as low as 1%. Therefore eliminating the undissolved air, or any separate gaseous phase, from the system is essential for retaining the properties of isochoric freezing. Copyright © 2016. Published by Elsevier Inc.

Roles for Arabidopsis CAMTA transcription factors in cold-regulated gene expression and freezing tolerance.

PubMed

Doherty, Colleen J; Van Buskirk, Heather A; Myers, Susan J; Thomashow, Michael F

2009-03-01

The Arabidopsis thaliana CBF cold response pathway plays a central role in cold acclimation. It is characterized by rapid cold induction of genes encoding the CBF1-3 transcription factors, followed by expression of the CBF gene regulon, which imparts freezing tolerance. Our goal was to further the understanding of the cis-acting elements and trans-acting factors involved in expression of CBF2. We identified seven conserved DNA motifs (CM), CM1 to 7, that are present in the promoters of CBF2 and another rapidly cold-induced gene encoding a transcription factor, ZAT12. The results presented indicate that in the CBF2 promoter, CM4 and CM6 have negative regulatory activity and that CM2 has both negative and positive activity. A Myc binding site in the CBF2 promoter was also found to have positive regulatory effects. Moreover, our results indicate that members of the calmodulin binding transcription activator (CAMTA) family of transcription factors bind to the CM2 motif, that CAMTA3 is a positive regulator of CBF2 expression, and that double camta1 camta3 mutant plants are impaired in freezing tolerance. These results establish a role for CAMTA proteins in cold acclimation and provide a possible point of integrating low-temperature calcium and calmodulin signaling with cold-regulated gene expression.

Water at protein surfaces studied with femtosecond nonlinear spectroscopy

NASA Astrophysics Data System (ADS)

Bakker, Huib J.

We report on an investigation of the structure and dynamics of water molecules near protein surfaces with femtosecond nonlinear spectroscopic techniques. We measured the reorientation dynamics of water molecules near the surface of several globular protein surfaces, using polarization-resolved femtosecond infrared spectroscopy. We found that water molecules near the protein surface have a much slower reorientation than water molecules in bulk liquid water. The number of slow water molecules scales scales with the size of the hydrophobic surface of the protein. When we denature the proteins by adding an increasing amount of urea to the protein solution, we observe that the water-exposed surface increases by 50% before the secondary structure of the proteins changes. This finding indicates that protein unfolding starts with the protein structure becoming less tight, thereby allowing water to enter. With surface vibrational sum frequency generation (VSFG) spectroscopy, we studied the structure of water at the surface of antifreeze protein III. The measured VSFG spectra showed the presence of ice-like water layers at the ice-binding site of the protein in aqueous solution, at temperatures well above the freezing point. This ordered ice-like hydration layers at the protein surface likely plays an important role in the specific recognition and binding of anti-freeze protein III to nascent ice crystallites, and thus in its anti-freeze mechanism. This research is supported by the ''Nederlandse organisatie voor Wetenschappelijk Onderzoek (NWO).

Multiscale model of a freeze-thaw process for tree sap exudation.

PubMed

Graf, Isabell; Ceseri, Maurizio; Stockie, John M

2015-10-06

Sap transport in trees has long fascinated scientists, and a vast literature exists on experimental and modelling studies of trees during the growing season when large negative stem pressures are generated by transpiration from leaves. Much less attention has been paid to winter months when trees are largely dormant but nonetheless continue to exhibit interesting flow behaviour. A prime example is sap exudation, which refers to the peculiar ability of sugar maple (Acer saccharum) and related species to generate positive stem pressure while in a leafless state. Experiments demonstrate that ambient temperatures must oscillate about the freezing point before significantly heightened stem pressures are observed, but the precise causes of exudation remain unresolved. The prevailing hypothesis attributes exudation to a physical process combining freeze-thaw and osmosis, which has some support from experimental studies but remains a subject of active debate. We address this knowledge gap by developing the first mathematical model for exudation, while also introducing several essential modifications to this hypothesis. We derive a multiscale model consisting of a nonlinear system of differential equations governing phase change and transport within wood cells, coupled to a suitably homogenized equation for temperature on the macroscale. Numerical simulations yield stem pressures that are consistent with experiments and provide convincing evidence that a purely physical mechanism is capable of capturing exudation. © 2015 The Author(s).

Visual Indicators on Vaccine Boxes as Early Warning Tools to Identify Potential Freeze Damage.

PubMed

Angoff, Ronald; Wood, Jillian; Chernock, Maria C; Tipping, Diane

2015-07-01

The aim of this study was to determine whether the use of visual freeze indicators on vaccines would assist health care providers in identifying vaccines that may have been exposed to potentially damaging temperatures. Twenty-seven sites in Connecticut involved in the Vaccine for Children Program participated. In addition to standard procedures, visual freeze indicators (FREEZEmarker ® L; Temptime Corporation, Morris Plains, NJ) were affixed to each box of vaccine that required refrigeration but must not be frozen. Temperatures were monitored twice daily. During the 24 weeks, all 27 sites experienced triggered visual freeze indicator events in 40 of the 45 refrigerators. A total of 66 triggered freeze indicator events occurred in all 4 types of refrigerators used. Only 1 of the freeze events was identified by a temperature-monitoring device. Temperatures recorded on vaccine data logs before freeze indicator events were within the 35°F to 46°F (2°C to 8°C) range in all but 1 instance. A total of 46,954 doses of freeze-sensitive vaccine were stored at the time of a visual freeze indicator event. Triggered visual freeze indicators were found on boxes containing 6566 doses (14.0% of total doses). Of all doses stored, 14,323 doses (30.5%) were of highly freeze-sensitive vaccine; 1789 of these doses (12.5%) had triggered indicators on the boxes. Visual freeze indicators are useful in the early identification of freeze events involving vaccines. Consideration should be given to including these devices as a component of the temperature-monitoring system for vaccines.

The Adsorption and Desorption of Pb(2+) and Cd(2+) in Freeze-Thaw Treated Soils.

PubMed

Li, Linhui; Ma, Jincai; Xu, Meng; Li, Xu; Tao, Jiahui; Wang, Guanzhu; Yu, Jitong; Guo, Ping

2016-01-01

Adsorption and desorption are important processes that influence the potential toxicity and bioavailability of heavy metals in soils. However, information regarding adsorption and desorption behavior of heavy metals in soils subjected to freeze-thaw cycles is poorly understood. In the current study, the effect of freeze-thaw cycles with different freezing temperature (-15, -25, -35°C) on soil properties was investigated. Then the adsorption and desorption behavior of Pb(2+) and Cd(2+) in freeze-thaw treated soils was studied. The adsorption amounts of Pb(2+) and Cd(2+) in freeze-thaw treated soils were smaller than those in unfrozen soils (p < 0.05), due to the fact that pH, cation exchange capacity, organic matter content, free iron oxide content, and CaCO3 content in freeze-thaw treated soils were smaller than those in unfrozen soils. The adsorption amounts of Pb(2+) and Cd(2+) in soils treated with lower freezing temperatures were higher than those in soils treated with higher freezing temperatures. Desorption percentages of Pb(2+) and Cd(2+) in unfrozen soils were smaller than those in freeze-thaw treated soils (p < 0.05). The desorption percentages of Pb(2+) and Cd(2+) were smaller in soils treated with lower freezing temperatures than those in soils treated with higher freezing temperatures. The results obtained highlight the change of the adsorption and desorption behavior of typical heavy metals in freeze-thaw treated soils located in seasonal frozen soils zone in northeast China.

Evaluating Long-Term Impacts of Soil-Mixing Source-Zone Treatment using Cryogenic Core Collection

DTIC Science & Technology

2017-06-01

to (a) coring equipment freezing downhole, (b) freezing or binding of the core sample in barrel, and ( c ) running out of LN in the vicinity of sampling...encountered due to (a) coring equipment freezing downhole, (b) freezing or binding of the core sample in barrel, and ( c ) running out of LN in the...equipment freezing downhole, (b) freezing or binding of the core sample in barrel, and ( c ) running out of LN in the vicinity of sampling. Downhole

Experimental Studies in Ice Nucleation

NASA Astrophysics Data System (ADS)

Wright, Timothy Peter

Ice nuclei play a critical role in the formation of precipitation in mixed phase clouds. Modification of IN concentrations can lead to changes in cloud lifetimes and precipitation size. Presented in this study are experimental investigations into ice nuclei in an ongoing effort to reduce the uncertainties that ice nuclei have on cloud processes and climate. This research presents a new version of the cold stage drop freezing assay to investigate the time-dependence of heterogeneous nucleation. The temperature range for the instrument spans from the melting point of water to the homogeneous freezing limit of ˜-38 deg C. Temperature stability for the instrument allowed for experimental operation for up to four days while interrogating the same sample. Up to a one hundred fold increase in the number of analyzed drops was accomplished through an in-house written automated drop freezing detection software package. Combined instrument design improvements allow for the analysis of IN concentrations down to ˜10-8 ice nuclei per picoliter of sample water. A new variant of the multiple-component stochastic model for heterogeneous ice nucleation was used to investigate the time dependence of heterogeneous freezing processes. This was accomplished by analyzing how the changes in the cooling rate can impact the observed nucleation rate. The model employed four material-dependent parameters to accurately capture the observed freezing of water drops containing Arizona Test Dust. The parameters were then used to accurately predict the freezing behavior of the drops in time dependent experiments. The time dependence freezing of a wide range of materials was then investigated. These materials included the minerals montmorillonite and kaolinite, the biological proxy ice nuclei contained within the product Icemax, and flame soot generated from the incomplete combustion of ethylene gas. The time dependence for ice nuclei collected from rainwater samples was also investigated. The data show that the time dependence for all investigated materials was weak. The drop freezing assay was then employed to test the hypothesis that certain macromolecules derived from burst pollen could be efficient ice nuclei. In a new method, air samples were collected during the height of the 2013 pollen season using a particle-in-liquid impinger and the solutions were transferred to the drop freezing assay to be analyzed for ice nuclei activity. The IN concentration in collected rainwater was analyzed and compared to IN concentrations near the ground to determine if potential IN enhancement due to pollen bursting at the surface was also found within clouds. No general trend was observed between ambient pollen counts and observed IN concentrations, suggesting that ice nuclei multiplication via pollen sac rupturing and the subsequent release of macromolecules was not prevalent for the pollen types and meteorological conditions typically encountered in the Southeastern US. Additional field tests were performed in conjunction with the Wideband Integrated Bioaerosol Sensor which used UV fluorescence to determine the possible fraction of biological aerosol present at the measurement site. This instrument was operated in parallel with the particle-in-liquid impinger allowing for a comparison of ambient immersion mode ice nuclei and fluorescent particle concentrations. Two case studies provided evidence that the active release of biological ice nuclei was causally coordinated with the arrival of a cold-frontal boundary, which can loft the nuclei to seed the frontal cloud rain band.

Insufficiency of copper ion homeostasis causes freeze-thaw injury of yeast cells as revealed by indirect gene expression analysis.

PubMed

Takahashi, Shunsuke; Ando, Akira; Takagi, Hiroshi; Shima, Jun

2009-11-01

Saccharomyces cerevisiae is exposed to freeze-thaw stress in commercial processes, including frozen dough baking. Cell viability and fermentation activity after a freeze-thaw cycle were dramatically decreased due to freeze-thaw injury. Because this type of injury involves complex phenomena, the injury mechanisms are not fully understood. We examined freeze-thaw injury by indirect gene expression analysis during postthaw incubation after freeze-thaw treatment using DNA microarray profiling. The results showed that genes involved in the homeostasis of metal ions were frequently contained in genes that were upregulated, depending on the freezing period. We assessed the phenotype of deletion mutants of the metal ion homeostasis genes that exhibited freezing period-dependent upregulation and found that the strains with deletion of the MAC1 and CTR1 genes involved in copper ion homeostasis exhibited freeze-thaw sensitivity, suggesting that copper ion homeostasis is required for freeze-thaw tolerance. We found that supplementation with copper ions during postthaw incubation increased intracellular superoxide dismutase activity and intracellular levels of reactive oxygen species were decreased. Moreover, cell viability was increased by supplementation with copper ions. These results suggest that insufficiency of copper ion homeostasis may be one of the causes of freeze-thaw injury.

Application of the Quality by Design Approach to the Freezing Step of Freeze-Drying: Building the Design Space.

PubMed

Arsiccio, Andrea; Pisano, Roberto

2018-06-01

The present work shows a rational method for the development of the freezing step of a freeze-drying cycle. The current approach to the selection of freezing conditions is still empirical and nonsystematic, thus resulting in poor robustness of control strategy. The final aim of this work is to fill this gap, describing a rational procedure, based on mathematical modeling, for properly choosing the freezing conditions. Mechanistic models are used for the prediction of temperature profiles during freezing and dimension of ice crystals being formed. Mathematical description of the drying phase of freeze-drying is also coupled with the results obtained by freezing models, thus providing a comprehensive characterization of the lyophilization process. In this framework, deep understanding of the phenomena involved is required, and according to the Quality by Design approach, this knowledge can be used to build the design space. The step-by-step procedure for building the design space for freezing is thus described, and examples of applications are provided. The calculated design space is validated upon experimental data, and we show that it allows easy control of the freezing process and fast selection of appropriate operating conditions. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Recent developments in smart freezing technology applied to fresh foods.

PubMed

Xu, Ji-Cheng; Zhang, Min; Mujumdar, Arun S; Adhikari, Benu

2017-09-02

Due to the increased awareness of consumers in sensorial and nutritional quality of frozen foods, the freezing technology has to seek new and innovative technologies for better retaining the fresh like quality of foods. In this article, we review the recent developments in smart freezing technology applied to fresh foods. The application of these intelligent technologies and the associated underpinning concepts have greatly improved the quality of frozen foods and the freezing efficiency. These technologies are able to automatically collect the information in-line during freezing and help control the freezing process better. Smart freezing technology includes new and intelligent technologies and concepts applied to the pretreatment of the frozen product, freezing processes, cold chain logistics as well as warehouse management. These technologies enable real-time monitoring of quality during the freezing process and help improve product quality and freezing efficiency. We also provide a brief overview of several sensing technologies used to achieve automatic control of individual steps of freezing process. These sensing technologies include computer vision, electronic nose, electronic tongue, digital simulation, confocal laser, near infrared spectroscopy, nuclear magnetic resonance technology and ultrasound. Understanding of the mechanism of these new technologies will be helpful for applying them to improve the quality of frozen foods.

Freezing tolerance of winter wheat as influenced by extended growth at low temperature and exposure to freeze-thaw cycles

USDA-ARS?s Scientific Manuscript database

As the seasons progress, autumn-planted winter wheat plants (Triticum aestivum L.) first gain, then progressively lose freezing tolerance. Exposing the plants to freeze-thaw cycles of -3/3°C results in increased ability to tolerate subsequent freezing to potentially damaging temperatures. This stu...

Host-mediated shift in the cold tolerance of an invasive insect

Treesearch

Amy C. Morey; Robert C. Venette; Erica C. Nystrom Santacruz; Laurel A. Mosca; W. D. Hutchison

2016-01-01

While many insects cannot survive the formation of ice within their bodies, a few species can. On the evolutionary continuum from freeze-intolerant (i.e., freeze-avoidant) to freeze-tolerant insects, intermediates likely exist that can withstand some ice formation, but not enough to be considered fully freeze tolerant. Theory suggests that freeze tolerance should be...

Phenomenological consequences of enhanced bulk viscosity near the QCD critical point

DOE PAGES

Monnai, Akihiko; Mukherjee, Swagato; Yin, Yi

2017-03-06

In the proximity of the QCD critical point the bulk viscosity of quark-gluon matter is expected to be proportional to nearly the third power of the critical correlation length, and become significantly enhanced. Here, this work is the first attempt to study the phenomenological consequences of enhanced bulk viscosity near the QCD critical point. For this purpose, we implement the expected critical behavior of the bulk viscosity within a non-boost-invariant, longitudinally expanding 1 + 1 dimensional causal relativistic hydrodynamical evolution at nonzero baryon density. We demonstrate that the critically enhanced bulk viscosity induces a substantial nonequilibrium pressure, effectively softening themore » equation of state, and leads to sizable effects in the flow velocity and single-particle distributions at the freeze-out. In conclusion, the observable effects that may arise due to the enhanced bulk viscosity in the vicinity of the QCD critical point can be used as complementary information to facilitate searches for the QCD critical point.« less

Freezing pattern and frost killing temperature of apple (Malus domestica) wood under controlled conditions and in nature.

PubMed

Pramsohler, Manuel; Hacker, Jürgen; Neuner, Gilbert

2012-07-01

The freezing pattern and frost killing temperatures of apple (Malus domestica Borkh.) xylem were determined by differential thermal analysis and infrared differential thermal analysis (IDTA). Results from detached or attached twigs in controlled freezing experiments and during natural field freezing of trees were compared. Non-lethal freezing of apoplastic water in apple xylem as monitored during natural winter frosts in the field occurred at -1.9 ± 0.4 °C and did not change seasonally. The pattern of whole tree freezing was variable and specific to the environmental conditions. On detached twigs high-temperature freezing exotherms (HTEs) occurred 2.8 K below the temperature observed under natural frosts in the field with a seasonal mean of -4.7 ± 0.5 °C. Microporous apple xylem showed freezing without a specific pattern within a few seconds in IDTA images during HTEs, which is in contrast to macroporous xylem where a 2D freezing pattern mirrors anatomical structures. The pith tissue always remained unfrozen. Increasing twig length increased ice nucleation temperature; for increased twig diameter the effect was not significant. In attached twigs frozen in field portable freezing chambers, HTEs were recorded at a similar mean temperature (-4.6 ± 1.0 °C) to those for detached twigs. Upon lethal intracellular freezing of apple xylem parenchyma cells (XPCs) low-temperature freezing exotherms (LTEs) can be recorded. Low-temperature freezing exotherms determined on detached twigs varied significantly between a winter minimum of -36.9 °C and a summer maximum -12.7 °C. Within the temperature range wherein LTEs were recorded by IDTA in summer (-12.7 ± 0.5 to -20.3 ± 1.1 °C) various tiny clearly separated discontinuous freezing events could be detected similar to that in other species with contrasting XPC anatomy. These freezing events appeared to be initially located in the primary and only later in the secondary xylem. During the LTE no freezing events in the bark and central pith tissue were recorded. Attached twigs were exposed to various freezing temperatures at which LTEs occur. Even if 60% of XPCs were frost-damaged twigs were able to recuperate and showed full re-growth indicating a high regeneration capacity even after severe frost damage to XPCs.

Defensive freezing links Hypothalamic-Pituitary-Adrenal-axis activity and internalizing symptoms in humans.

PubMed

Niermann, Hannah C M; Figner, Bernd; Tyborowska, Anna; van Peer, Jacobien M; Cillessen, Antonius H N; Roelofs, Karin

2017-08-01

The Hypothalamic-Pituitary-Adrenal (HPA)-axis plays an important role in the expression of defensive freezing. Adaptive freezing reactivity, characterized by an immediate increase in acute stress and timely termination upon threat offset or need to act, is essential for adequate stress coping. Blunted HPA-axis activity in animals is associated with blunted freezing reactivity and internalizing symptoms. Despite their potential relevance, it remains unknown whether these mechanisms apply to humans and human psychopathology. Using a well-established method combining electrocardiography and posturography, we assessed freezing before, immediately after, and one hour after a stress induction in 92 human adolescents. In line with animal models, human adolescents showed stress-induced freezing, as quantified by relative reductions in heart rate and body sway after, as compared to before, stress. Moreover, relatively lower basal cortisol was associated with reduced stress-induced freezing reactivity (i.e., less immediate freezing and less recovery). Path analyses showed that decreased freezing recovery in individuals with reduced cortisol levels was associated with increased levels of internalizing symptoms. These findings suggest that reduced freezing recovery may be a promising marker for the etiology of internalizing symptoms. Copyright © 2017 Elsevier Ltd. All rights reserved.

Improving survival and storage stability of bacteria recalcitrant to freeze-drying: a coordinated study by European culture collections.

PubMed

Peiren, Jindrich; Buyse, Joke; De Vos, Paul; Lang, Elke; Clermont, Dominique; Hamon, Sylviane; Bégaud, Evelyne; Bizet, Chantal; Pascual, Javier; Ruvira, María A; Macián, M Carmen; Arahal, David R

2015-04-01

The objective of this study is to improve the viability after freeze-drying and during storage of delicate or recalcitrant strains safeguarded at biological resource centers. To achieve this objective, a joint experimental strategy was established among the different involved partner collections of the EMbaRC project ( www.embarc.eu ). Five bacterial strains considered as recalcitrant to freeze-drying were subjected to a standardized freeze-drying protocol and to seven agreed protocol variants. Viability of these strains was determined before and after freeze-drying (within 1 week, after 6 and 12 months, and after accelerated storage) for each of the protocols. Furthermore, strains were exchanged between partners to perform experiments with different freeze-dryer-dependent parameters. Of all tested variables, choice of the lyoprotectant had the biggest impact on viability after freeze-drying and during storage. For nearly all tested strains, skim milk as lyoprotectant resulted in lowest viability after freeze-drying and storage. On the other hand, best freeze-drying and storage conditions were strain and device dependent. For Aeromonas salmonicida CECT 894(T), best survival was obtained when horse serum supplemented with trehalose was used as lyoprotectant, while Aliivibrio fischeri LMG 4414(T) should be freeze-dried in skim milk supplemented with marine broth in a 1:1 ratio. Freeze-drying Campylobacter fetus CIP 53.96(T) using skim milk supplemented with trehalose as lyoprotectant resulted in best recovery. Xanthomonas fragariae DSM 3587(T) expressed high viability after freeze-drying and storage for all tested lyoprotectants and could not be considered as recalcitrant. In contrary, Flavobacterium columnare LMG 10406(T) did not survive the freeze-drying process under all tested conditions.

State transitions and physicochemical aspects of cryoprotection and stabilization in freeze-drying of Lactobacillus rhamnosus GG (LGG).

PubMed

Pehkonen, K S; Roos, Y H; Miao, S; Ross, R P; Stanton, C

2008-06-01

The frozen and dehydrated state transitions of lactose and trehalose were determined and studied as factors affecting the stability of probiotic bacteria to understand physicochemical aspects of protection against freezing and dehydration of probiotic cultures. Lactobacillus rhamnosus GG was frozen (-22 or -43 degrees C), freeze-dried and stored under controlled water vapour pressure (0%, 11%, 23% and 33% relative vapour pressure) conditions. Lactose, trehalose and their mixture (1 : 1) were used as protective media. These systems were confirmed to exhibit relatively similar state transition and water plasticization behaviour in freeze-concentrated and dehydrated states as determined by differential scanning calorimetry. Ice formation and dehydrated materials were studied using cold-stage microscopy and scanning electron microscopy. Trehalose and lactose-trehalose gave the most effective protection of cell viability as observed from colony forming units after freezing, dehydration and storage. Enhanced cell viability was observed when the freezing temperature was -43 degrees C. State transitions of protective media affect ice formation and cell viability in freeze-drying and storage. Formation of a maximally freeze-concentrated matrix with entrapped microbial cells is essential in freezing prior to freeze-drying. Freeze-drying must retain a solid amorphous state of protectant matrices. Freeze-dried matrices contain cells entrapped in the protective matrices in the freezing process. The retention of viability during storage seems to be controlled by water plasticization of the protectant matrix and possibly interactions of water with the dehydrated cells. Highest cell viability was obtained in glassy protective media. This study shows that physicochemical properties of protective media affect the stability of dehydrated cultures. Trehalose and lactose may be used in combination, which is particularly important for the stabilization of probiotic bacteria in dairy systems.

Experimental analysis and modeling of ultrasound assisted freezing of potato spheres.

PubMed

Kiani, Hossein; Zhang, Zhihang; Sun, Da-Wen

2015-09-01

In recent years, innovative methods such as ultrasound assisted freezing have been developed in order to improve the freezing process. During freezing of foods, accurate prediction of the temperature distribution, phase ratios, and process time is very important. In the present study, ultrasound assisted immersion freezing process (in 1:1 ethylene glycol-water solution at 253.15K) of potato spheres (0.02 m diameter) was evaluated using experimental, numerical and analytical approaches. Ultrasound (25 kHz, 890 W m(-2)) was irradiated for different duty cycles (DCs=0-100%). A finite volume based enthalpy method was used in the numerical model, based on which temperature and liquid fraction profiles were simulated by a program developed using OpenFOAM® CFD software. An analytical technique was also employed to calculate freezing times. The results showed that ultrasound irradiation could decrease the characteristic freezing time of potatoes. Since ultrasound irradiation increased the heat transfer coefficient but simultaneously generated heat at the surface of the samples, an optimum DC was needed for the shortest freezing time which occurred in the range of 30-70% DC. DCs higher than 70% increased the freezing time. DCs lower than 30% did not provide significant effects on the freezing time compared to the control sample. The numerical model predicted the characteristic freezing time in accordance with the experimental results. In addition, analytical calculation of characteristic freezing time exhibited qualitative agreement with the experimental results. As the numerical simulations provided profiles of temperature and water fraction within potatoes frozen with or without ultrasound, the models can be used to study and control different operation situations, and to improve the understanding of the freezing process. Copyright © 2015 Elsevier B.V. All rights reserved.

Mechanisms of deterioration of nutrients phase 1

NASA Technical Reports Server (NTRS)

Karel, M.; Flink, J. M.

1972-01-01

Experimental methods are studied by which freeze-dried foods of improved quality are produced. Considered are: (1) Factors effecting the loss of butanol from frozen aqueous food solutions during storage; (2) a freeze-drying microscope system for observing solidification processes in organic mixtures and aqueous inorganic salt solutions; (3) browning of high quality freeze-dried foods with minimal organoleptic and nutritional detoriation; (4) retention of PVP-n-propanol in freeze-dried food models; and (5) effects of freezing rate and sucrose immersion on taste and texture of freeze-dried apple slices.

Colder freeze-in axinos decaying into photons

NASA Astrophysics Data System (ADS)

Bae, Kyu Jung; Kamada, Ayuki; Liew, Seng Pei; Yanagi, Keisuke

2018-03-01

We point out that 7 keV axino dark matter (DM) in the R-parity violating (RPV) supersymmetric (SUSY) Dine-Fischler-Srednicki-Zhitnitsky axion model can simultaneously reproduce the 3.5 keV x-ray line excess and evade stringent constraints from the Ly -α forest data. Peccei-Quinn symmetry breaking naturally generates both the TeV-scale μ term and the MeV-scale RPV term. The RPV term introduces a tiny axino-neutrino mixing and provides axino DM as a variant of the sterile neutrino DM explaining the 3.5 keV x-ray line excess. Axinos are produced by freeze-in processes via the μ term. The resultant phase space distribution tends to be colder than the Fermi-Dirac distribution. The inherent entropy production from late-time saxion decay makes axinos even colder than those without saxion decay. The resultant axino DM takes the correct relic density and is compatible even with the latest and strongest constraint from the Ly-α forest data.

Regional and seasonal limitations for Mars intrinsic ecopoiesis.

PubMed

Badescu, Viorel

2005-04-01

Mars ecopoiesis is a human controlled process consisting in changes needed for anaerobic life to be established on planet surface. The daily minimum temperature on present day Mars is well below the water freezing point, due to the low thermal inertia of the surface. A simple time-dependent model to evaluate the ground temperature is developed here. It takes into account the incident solar radiation, the greenhouse effect and surface thermal inertia. The model is applied to two modified Martian atmospheres. Increasing surface thermal inertia seems to be necessary for Mars intrinsic ecopoiesis. This can be done either by removing the regolith layer covering the bedrock or by regolith compression. The Northern hemisphere of the terraformed Mars appears to be more hospitable than the Southern hemisphere, because the amplitude of the daily temperature excursion there is lower and the freezing temperature appears at higher latitudes. A regional (and seasonal) terraforming of Mars is suggested. c2005 Elsevier Ltd. All rights reserved.

Ice-nucleating bacteria control the order and dynamics of interfacial water

DOE PAGES

Pandey, Ravindra; Usui, Kota; Livingstone, Ruth A.; ...

2016-04-22

Ice-nucleating organisms play important roles in the environment. With their ability to induce ice formation at temperatures just below the ice melting point, bacteria such as Pseudomonas syringae attack plants through frost damage using specialized ice-nucleating proteins. Besides the impact on agriculture and microbial ecology, airborne P. syringae can affect atmospheric glaciation processes, with consequences for cloud evolution, precipitation, and climate. Biogenic ice nucleation is also relevant for artificial snow production and for biomimetic materials for controlled interfacial freezing. We use interface-specific sum frequency generation (SFG) spectroscopy to show that hydrogen bonding at the water-bacteria contact imposes structural ordering onmore » the adjacent water network. Experimental SFG data and molecular dynamics simulations demonstrate that ice active sites within P. syringae feature unique hydrophilic-hydrophobic patterns to enhance ice nucleation. Finally, the freezing transition is further facilitated by the highly effective removal of latent heat from the nucleation site, as apparent from time-resolved SFG spectroscopy.« less

Mechanical performance and thermal stability of glass fiber reinforced silica aerogel composites based on co-precursor method by freeze drying

NASA Astrophysics Data System (ADS)

Zhou, Ting; Cheng, Xudong; Pan, Yuelei; Li, Congcong; Gong, Lunlun; Zhang, Heping

2018-04-01

In order to maintain the integrity, glass fiber (GF) reinforced silica aerogel composites were synthesized using methltrimethoxysilane (MTMS) and water glass co-precursor by freeze drying method. The composites were characterized by scanning electron microscopy, Brunauer-Emmett-Teller analysis, uniaxial compressive test, three-point bending test, thermal conductivity analysis, contact angle test, TG-DSC analysis. It was found that the molar ratio of MTMS/water glass could significantly affect the properties of composites. The bulk density and thermal conductivity first decreased and then increased with the increasing molar ratio. The composites showed remarkable mechanical strength and flexibility compared with pure silica aerogel. Moreover, when the molar ratio is 1.8, the composites showed high specific surface area (870.9 m2/g), high contact angle (150°), great thermal stability (560 °C) and low thermal conductivity (0.0248 W/m·K). These outstanding properties indicate that GF/aerogels have broad prospects in the field of thermal insulation.

Heat pump with freeze-up prevention

DOEpatents

Ecker, Amir L.

1981-01-01

What is disclosed is a heat pump apparatus for conditioning a fluid characterized by a fluid handler and path for circulating the fluid in heat exchange relationship with a refrigerant fluid; at least two refrigerant heat exchangers, one for effecting heat exchange with the fluid and a second for effecting heat exchange between refrigerant and a heat exchange fluid and the ambient air; a compressor for efficiently compressing the refrigerant; at least one throttling valve for throttling liquid refrigerant; a refrigerant circuit; refrigerant; a source of heat exchange fluid; heat exchange fluid circulating device and heat exchange fluid circuit for circulating the heat exchange fluid in heat exchange relationship with the refrigerant; and valves or switches for selecting the heat exchangers and direction of flow of the refrigerant therethrough for selecting a particular mode of operation. The heat exchange fluid prevents freeze up of the second heat exchanger by keeping the temperature above the dew point; and, optionally, provides heat for efficient operation.

Supermacroporous chemically cross-linked poly(aspartic acid) hydrogels.

PubMed

Gyarmati, Benjámin; Mészár, E Zsuzsanna; Kiss, Lóránd; Deli, Mária A; László, Krisztina; Szilágyi, András

2015-08-01

Chemically cross-linked poly(aspartic acid) (PASP) gels were prepared by a solid-liquid phase separation technique, cryogelation, to achieve a supermacroporous interconnected pore structure. The precursor polymer of PASP, polysuccinimide (PSI) was cross-linked below the freezing point of the solvent and the forming crystals acted as templates for the pores. Dimethyl sulfoxide was chosen as solvent instead of the more commonly used water. Thus larger temperatures could be utilized for the preparation and the drawback of increase in specific volume of water upon freezing could be eliminated. The morphology of the hydrogels was characterized by scanning electron microscopy and interconnectivity of the pores was proven by the small flow resistance of the gels. Compression tests also confirmed the interconnected porous structure and the complete re-swelling and shape recovery of the supermacroporous PASP hydrogels. The prepared hydrogels are of interest for several biomedical applications as scaffolding materials because of their cytocompatibility, controllable morphology and pH-responsive character. Copyright © 2015 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Polymer Structure and Water States in Salt-Containing Polyampholyte Hydrogels

NASA Astrophysics Data System (ADS)

Li, Xinda; Elliott, Janet A. W.; Lee, Byeongdu; Chung, Hyun-Joong

The phase behavior of water in hydrogels has broad impact on various applications, such as lubrication, adhesion, and electrical conductivity, as well as the hydrogel's low temperature properties. The status of the water molecules is correlated to the structure of the polymer chains in the hydrogel. In this study, the structure and water status of a model charge-balanced polyampholyte poly(4-vinylbenzenesulfonate-co-[3-(methacryloylamino) propyl] trimethylammonium chloride), were investigated by using differential scanning calorimetry (DSC) and small-angle x-ray scattering (SAXS). A globular network structure suggested by SAXS results dictated the depression of the freezing point of water in the hydrogel, as supported by the DSC results. The polyampholyte chains undergo an irreversible collapse during dialysis in deionized water. Such collapsed hydrogels are not able to prevent freezing of water molecules. The results of both synthesis condition and post-synthesis treatments for polyampholyte hydrogels provide us insights to design optimal polyampholyte hydrogels for low temperature applications.

Mass production of shaped particles through vortex ring freezing

PubMed Central

An, Duo; Warning, Alex; Yancey, Kenneth G.; Chang, Chun-Ti; Kern, Vanessa R.; Datta, Ashim K.; Steen, Paul H.; Luo, Dan; Ma, Minglin

2016-01-01

A vortex ring is a torus-shaped fluidic vortex. During its formation, the fluid experiences a rich variety of intriguing geometrical intermediates from spherical to toroidal. Here we show that these constantly changing intermediates can be ‘frozen' at controlled time points into particles with various unusual and unprecedented shapes. These novel vortex ring-derived particles, are mass-produced by employing a simple and inexpensive electrospraying technique, with their sizes well controlled from hundreds of microns to millimetres. Guided further by theoretical analyses and a laminar multiphase fluid flow simulation, we show that this freezing approach is applicable to a broad range of materials from organic polysaccharides to inorganic nanoparticles. We demonstrate the unique advantages of these vortex ring-derived particles in several applications including cell encapsulation, three-dimensional cell culture, and cell-free protein production. Moreover, compartmentalization and ordered-structures composed of these novel particles are all achieved, creating opportunities to engineer more sophisticated hierarchical materials. PMID:27488831

Ice-nucleating bacteria control the order and dynamics of interfacial water

PubMed Central

Pandey, Ravindra; Usui, Kota; Livingstone, Ruth A.; Fischer, Sean A.; Pfaendtner, Jim; Backus, Ellen H. G.; Nagata, Yuki; Fröhlich-Nowoisky, Janine; Schmüser, Lars; Mauri, Sergio; Scheel, Jan F.; Knopf, Daniel A.; Pöschl, Ulrich; Bonn, Mischa; Weidner, Tobias

2016-01-01

Ice-nucleating organisms play important roles in the environment. With their ability to induce ice formation at temperatures just below the ice melting point, bacteria such as Pseudomonas syringae attack plants through frost damage using specialized ice-nucleating proteins. Besides the impact on agriculture and microbial ecology, airborne P. syringae can affect atmospheric glaciation processes, with consequences for cloud evolution, precipitation, and climate. Biogenic ice nucleation is also relevant for artificial snow production and for biomimetic materials for controlled interfacial freezing. We use interface-specific sum frequency generation (SFG) spectroscopy to show that hydrogen bonding at the water-bacteria contact imposes structural ordering on the adjacent water network. Experimental SFG data and molecular dynamics simulations demonstrate that ice-active sites within P. syringae feature unique hydrophilic-hydrophobic patterns to enhance ice nucleation. The freezing transition is further facilitated by the highly effective removal of latent heat from the nucleation site, as apparent from time-resolved SFG spectroscopy. PMID:27152346

Human Milk Composition: Nutrients and Bioactive Factors

PubMed Central

Ballard, Olivia; Morrow, Ardythe L.

2013-01-01

Synopsis The composition of human milk is the biologic norm for infant nutrition. Human milk also contains many hundreds to thousands of distinct bioactive molecules that protect against infection and inflammation and contribute to immune maturation, organ development, and healthy microbial colonization. Some of these molecules, e.g., lactoferrin, are being investigated as novel therapeutic agents. A dynamic, bioactive fluid, human milk changes in composition from colostrum to late lactation, and varies within feeds, diurnally, and between mothers. Feeding infants with expressed human milk is increasing. Pasteurized donor milk is now commonly provided to high risk infants and most mothers in the U.S. express and freeze their milk at some point in lactation for future infant feedings. Many milk proteins are degraded by heat treatment and freeze-thaw cycles may not have the same bioactivity after undergoing these treatments. This article provides an overview of the composition of human milk, sources of its variation, and its clinical relevance. PMID:23178060

Low temperature self-cleaning properties of superhydrophobic surfaces

NASA Astrophysics Data System (ADS)

Wang, Fajun; Shen, Taohua; Li, Changquan; Li, Wen; Yan, Guilong

2014-10-01

Outdoor surfaces are usually dirty surfaces. Ice accretion on outdoor surfaces could lead to serious accidents. In the present work, the superhydrophobic surface based on 1H, 1H, 2H, 2H-Perfluorodecanethiol (PFDT) modified Ag/PDMS composite was prepared to investigate the anti-icing property and self-cleaning property at temperatures below freezing point. The superhydrophobic surface was deliberately polluted with activated carbon before testing. It was observed that water droplet picked up dusts on the cold superhydrophobic surface and took it away without freezing at a measuring temperature of -10 °C. While on a smooth PFDT surface and a rough surface base on Ag/PDMS composite without PFDT modification, water droplets accumulated and then froze quickly at the same temperature. However, at even lower temperature of -12 °C, the superhydrophobic surface could not prevent the surface water from icing. In addition, it was observed that the frost layer condensed from the moisture pay an important role in determining the low temperature self-cleaning properties of a superhydrophobic surface.

Comparison of various types of starch when used in meat sausages.

PubMed

Skrede, G

1989-01-01

Technological and sensory properties of meat sausages formulated with 4·0% of either potato flour, modified (acetylated distarch phosphate) potato starch, wheat, corn or tapioca starch were compared. Sausages were analyzed after cooking at temperatures between 65 and 85°C followed by storage at 5°C and -25°C. Characteristics evaluated were weight loss during cooking and storage, instrumentally and sensory assessed firmness, taste and smell of sausages. The results revealed differences in the suitability of starches for use in meat sausages. Part of the differences could be ascribed to differences in gelatination properties of the starches. With the criteria used for evaluating quality, potato flour was rated as the best suited starch followed by wheat starch while tapioca was rated as the least suited. Corn starch required cooking temperatures above 75°C and showed relatively low freeze/thaw stability. The modified potato starch stored well both above and below the freezing point. Copyright © 1989. Published by Elsevier Ltd.

Use of Unmanned Aerial Systems to Study Atmospheric Processes During Sea Ice Freeze Up

NASA Astrophysics Data System (ADS)

de Boer, G.; Lawrence, D.; Weibel, D.; Borenstein, S.; Bendure, A.; Solomon, A.; Intrieri, J. M.

2017-12-01

In October 2016, a team of scientists deployed to Oliktok Point, Alaska to make atmospheric measurements as part of the Evaluation of Routine Atmospheric Sounding measurements using Unmanned Systems (ERASMUS) and Inaugural Campaigns for ARM Research using Unmanned Systems (ICARUS) campaigns. The deployment included operations using the University of Colorado DataHawk2 UAS. The DataHawk2 was configured to make measurements of atmospheric thermodynamics, wind and surface temperature, providing information on lower tropospheric thermodynamic structure, turbulent surface fluxes, and surface temperature. During this campaign, the team experienced a variety of weather regimes and witnessed the development of near shore sea ice. In this presentation, we will give an overview of the measurements obtained during this time and how they were used to better understand freeze up processes in this coastal environment. Additionally, we will provide insight into how these platforms are being used for evaluation of a fully-coupled sea ice forecast model operated by NOAA's Physical Sciences Division.

Water under inner pressure: a dielectric spectroscopy study.

PubMed

Angulo-Sherman, Abril; Mercado-Uribe, Hilda

2014-02-01

Water is the most studied substance on Earth. However, it is not completely understood why its structural and dynamical properties give rise to some anomalous behaviors. Some of them emerge when experiments at low temperatures and/or high pressures are performed. Here we report dielectric measurements on cold water under macroscopically constrained conditions, i.e., water in a large container at constant volume that cannot freeze below the melting point. The inner pressure in these conditions shifts the α relaxation peak to similar frequencies as seen in ice Ih. At 267 K we observe a peculiar response possibly due to the Grotthuss mechanism. At 251 K (the triple point) ice III forms.

Fuels characterization studies. [jet fuels

NASA Technical Reports Server (NTRS)

Seng, G. T.; Antoine, A. C.; Flores, F. J.

1980-01-01

Current analytical techniques used in the characterization of broadened properties fuels are briefly described. Included are liquid chromatography, gas chromatography, and nuclear magnetic resonance spectroscopy. High performance liquid chromatographic ground-type methods development is being approached from several directions, including aromatic fraction standards development and the elimination of standards through removal or partial removal of the alkene and aromatic fractions or through the use of whole fuel refractive index values. More sensitive methods for alkene determinations using an ultraviolet-visible detector are also being pursued. Some of the more successful gas chromatographic physical property determinations for petroleum derived fuels are the distillation curve (simulated distillation), heat of combustion, hydrogen content, API gravity, viscosity, flash point, and (to a lesser extent) freezing point.

Effect of moisture content on the invertase activity of freeze-dried S. cerevisiae.

PubMed

Pitombo, R N; Spring, C; Passos, R F; Tonato, M; Vitolo, M

1994-08-01

The invertase activity of intact Saccharomyces cerevisiae submitted to freezing-thawing was affected by pH, the chemical nature of the buffer, and the freezing cooling rate (CR), leading in some cases to a complete invertase inactivation (acetate buffer, pH 4.0, CR = 0.5 degree C/min). Once established under adequate freezing conditions the invertase activity remained unchanged after freeze-drying. Nevertheless, in some cases the cell-growing capability after freeze-drying diminished around 70%, mainly if the frozen cell suspension was attained through freezing carried out at CR = 0.5 degree C/min. Water sorption isotherms of freeze-dried samples (freeze-dryer Edwards L-4KR; 30 degrees C and 0.1 mB) were determined at 10 and 25 degrees C. The monolayer moisture content (MMC) at each temperature (12.7 and 3.71 for 10 and 25 degrees C, respectively) was calculated from isotherms by applying BET and GAB models. Freeze-dried yeast with water activity (Aw) between 0 and 0.33 (about the MMC value) maintained at 25 degrees C for 235 days and at 89 degrees C for 15 min retained at least 85% of its original invertase activity (IA), whereas samples with Aw > MMC lost at least 60% of its IA. X ray diffraction showed that the freeze-dried cake before and after storage presented an amorphous structure.

Changes in Ultrastructure and Sensory Characteristics on Electro-magnetic and Air Blast Freezing of Beef during Frozen Storage

PubMed Central

2015-01-01

The ultrastructure in the beef muscle of the electro-magnetic resonance and air blast freezing during the frozen storage, and the changes in the quality characteristics after thawing were evaluated. The size of ice crystal was small and evenly formed in the initial freezing period, and it showed that the size was increased as the storage period was elapsed (p<0.05). The beef stored by the electro-magnetic resonance freezing showed the size of ice crystal with a lower rate of increase than the air blast freezing during the frozen storage. The thawing loss of beef stored by the electro-magnetic resonance freezing was significantly lower than the air blast freezing during frozen storage (p<0.05), and it showed that the thawing loss of the round was higher than the loin. Water holding capacity decreased as the storage period became longer while the electro-magnetic resonance freezing was higher than the air blast on 8 month (p<0.05). As a result of sensory evaluation, the beef stored by the electro-magnetic resonance freezing did not show the difference until 4 months, and it showed higher acceptability in comparison with the beef stored by the air blast freezing. Thus, it is considered that the freezing method has an effect on the change in the ultrastructure and quality characteristics of the beef. PMID:26761797

Freeze-thaw durability of concrete: Ice formation process in pores

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cai, H.; Liu, X.

1998-09-01

Freeze-thaw durability of concrete is of great importance to hydraulic structures in cold areas. Study of ice formation process in concrete pores is necessary to evaluate the damages in concrete caused by freezing. In this paper, freezing of pore solution in concrete exposed to a freeze-thaw cycle is studied by following the change of concrete electrical conductivity with freezing temperatures. Concretes were subjected to freeze-thaw cycles with temperature varying between {minus}0 C and {minus}20 C. In the freezing process, the changing rate of concrete electrical conductivity obviously decreases at about {minus}10 C, indicating that more pore solution in concrete freezesmore » above {minus}10 C than below {minus}10C. According to Powers` static hydraulic pressure hypothesis, it is thought that frost damage mainly occurs between 0 C and {minus}100 C. To ordinary concrete, frost damages below {minus}10 C are negligible.« less

An Investigation to Improve Classifier Accuracy for Myo Collected Data

DTIC Science & Technology

2017-02-01

distribution is unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT A naïve Bayes classifier trained with 1,360 samples from 17 volunteers performs at...movement data from 17 volunteers . Each volunteer performed 8 gestures (Freeze, Rally Point, Hurry Up, Down, Come, Stop, Line Abreast Formation, and Vehicle...line chart was plotted for each gesture’s feature (e.g., Pitch, xAcc) per user. All 10 recorded samples of a particular gesture for a single volunteer

Prevention of Hydrogen-Induced Cracking in HY-130 Weldments.

DTIC Science & Technology

1977-09-30

cubic delta ferrite at the melting point (1538 C). The solu- bility increases from about k.9 to 8.3 ppm when delta ferrite transforms to * 3 The H... ferrite at 912 C. The solubility in ferrite then de- creases to less than 0.5 ppm at ambient temperature. This theory postulates that atomic...content than the dark- etching bands, and thus correspond to the regions last to freeze between the dendritic arms in the original ingot. During

Density and glass forming ability in amorphous atomic alloys: The role of the particle softness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Douglass, Ian; Hudson, Toby; Harrowell, Peter

A key property of glass forming alloys, the anomalously small volume difference with respect to the crystal, is shown to arise as a direct consequence of the soft repulsive potentials between metals. This feature of the inter-atomic potential is demonstrated to be responsible for a significant component of the glass forming ability of alloys due to the decrease in the enthalpy of fusion and the associated depression of the freezing point.

Environmentally friendly anti-icing

NASA Technical Reports Server (NTRS)

Zuk, John (Inventor); Haslim, Leonard A. (Inventor); Lockyer, Robert T. (Inventor)

1998-01-01

The present invention describes an aqueous, non-electrolytic, non-toxic, biodegradable, continuous single phase liquid anti-icing or deicing composition for use on the surfaces of, for example, aircraft, airport pavements, roadways, walkways, bridges, entrances, structures, canals, locks, components, vessels, nautical components, railroad switches, and motor vehicles. The anti-icing or deicing composition comprises: (a) water; (b) a non-toxic freezing point depressant selected from the group consisting of monohydric alcohols having from 2 to 6 carbon atoms, polyhydric alcohols having from 3 to 12 carbon atoms, monomethyl or ethyl ethers of polyhydric alcohols having from 3 to 12 atoms or mixtures thereof, wherein the freezing point depressant present is between about 14 to 60 percent by weight; (c) a thickener which is present in between about 0.01 and 10 percent by weight; and (d) optionally a corrosion inhibitor which is present in between about 0.01 and 0.1 percent by weight of the total composition. In one embodiment, the deicing composition further includes (e) a monohydric primary aliphatic unbranched alcohol as a means of forming a thin layer of the composition on the surface of the structure to be given ice protection, and/or as means of forming a homogenized foam with xanthan thickener; which alcohol is selected from the group consisting of alcohols having between 8 to 24 carbon atoms, preferably, 1-dodecanol. Compositions of water, propylene glycol, and/or propanol and xanthan are preferred.

Atomic-scale imaging of the dissolution of NaCl islands by water at low temperature

NASA Astrophysics Data System (ADS)

Peng, Jinbo; Guo, Jing; Ma, Runze; Meng, Xiangzhi; Jiang, Ying

2017-03-01

The dissolution of sodium chloride (NaCl) in water is a frequently encountered process in our daily lives. While the NaCl dissolution process in liquid water has been extensively studied, whether and how the dissolution occurs below the freezing point is still not clear. Using a low-temperature scanning tunneling microscope (STM), here we were able to directly visualize the dissolution of Au-supported NaCl (0 0 1) bilayer islands by water at atomic level. We found that the single water molecule on the STM tip can assist the extraction of single Na+ from the NaCl surface even at 5 K, while leaving the Cl- intact. When covered with a full water monolayer, the NaCl islands started to dissolve from the step edges and also showed evidence of dissolution inside the terraces as the temperature was raised up to 145 K. At 155 K, the water molecules completely desorbed from the surface, which was accompanied with the decomposition and restructuring of the bilayer NaCl islands. Those results suggest that the dissolution of NaCl may occur well below the freezing point at the ice/NaCl interfaces and is mainly driven by the interaction between the water molecules and the Na+, which is in clear contrast with the NaCl dissolution in liquid water.

Influence of stage of lactation and year season on composition of mares' colostrum and milk and method and time of storage on vitamin C content in mares' milk.

PubMed

Markiewicz-Kęszycka, Maria; Czyżak-Runowska, Grażyna; Wójtowski, Jacek; Jóźwik, Artur; Pankiewicz, Radosław; Łęska, Bogusława; Krzyżewski, Józef; Strzałkowska, Nina; Marchewka, Joanna; Bagnicka, Emilia

2015-08-30

Mares' milk is becoming increasingly popular in Western Europe. This study was thus aimed at investigating the impact of stage of lactation and season on chemical composition, somatic cell count and some physicochemical parameters of mares' colostrum and milk, and at developing a method for the determination of vitamin C (ascorbic acid) in mares' milk and to determine its content in fresh and stored milk. The analysis conducted showed an effect of the stage of lactation on contents of selected chemical components and physicochemical parameters of mares' milk. In successive lactation periods levels of fat, cholesterol, energy value, citric acid and titratable acidity decreased, whereas levels of lactose and vitamin C, as well as the freezing point, increased. Analysis showed that milk produced in autumn (September, October, November) had a higher freezing point and lower concentrations of total solids, protein, fat, cholesterol, citric acid and energy value in comparison to milk produced in summer (June, July, August). Mares' milk was characterised by low somatic cell count throughout lactation. In terms of vitamin C stability the most advantageous method of milk storage was 6-month storage of lyophilised milk. In general, the results confirmed that mares' milk is a raw material with a unique chemical composition different from that produced by other farm animals. © 2014 Society of Chemical Industry.

Crystal Initiation Structures in Developing Enamel: Possible Implications for Caries Dissolution of Enamel Crystals

PubMed Central

Robinson, Colin; Connell, Simon D.

2017-01-01

Investigations of developing enamel crystals using Atomic and Chemical Force Microscopy (AFM, CFM) have revealed a subunit structure. Subunits were seen in height images as collinear swellings about 30 nM in diameter on crystal surfaces. In friction mode they were visible as positive regions. These were similar in size (30–50 nM) to collinear spherical structures, presumably mineral matrix complexes, seen in developing enamel using a freeze fracturing/freeze etching procedure. More detailed AFM studies on mature enamel suggested that the 30–50 nM structures were composed of smaller units, ~10–15 nM in diameter. These were clustered in hexagonal or perhaps a spiral arrangement. It was suggested that these could be the imprints of initiation sites for mineral precipitation. The investigation aimed at examining original freeze etched images at high resolution to see if the smaller subunits observed using AFM in mature enamel were also present in developing enamel i.e., before loss of the organic matrix. The method used was freeze etching. Briefly samples of developing rat enamel were rapidly frozen, fractured under vacuum, and ice sublimed from the fractured surface. The fractured surface was shadowed with platinum or gold and the metal replica subjected to high resolution TEM. For AFM studies high-resolution tapping mode imaging of human mature enamel sections was performed in air under ambient conditions at a point midway between the cusp and the cervical margin. Both AFM and freeze etch studies showed structures 30–50 nM in diameter. AFM indicated that these may be clusters of somewhat smaller structures ~10–15 nM maybe hexagonally or spirally arranged. High resolution freeze etching images of very early enamel showed ~30–50 nM spherical structures in a disordered arrangement. No smaller units at 10–15 nM were clearly seen. However, when linear arrangements of 30–50 nM units were visible the picture was more complex but also smaller units including ~10–15 nM units could be observed. Conclusions: Structures ~10–15 nM in diameter were detected in developing enamel. While the appearance was complex, these were most evident when the 30–5 nM structures were in linear arrays. Formation of linear arrays of subunits may be associated with the development of mineral initiation sites and attendant processing of matrix proteins. PMID:28670283

Increased spring freezing vulnerability for alpine shrubs under early snowmelt.

PubMed

Wheeler, J A; Hoch, G; Cortés, A J; Sedlacek, J; Wipf, S; Rixen, C

2014-05-01

Alpine dwarf shrub communities are phenologically linked with snowmelt timing, so early spring exposure may increase risk of freezing damage during early development, and consequently reduce seasonal growth. We examined whether environmental factors (duration of snow cover, elevation) influenced size and the vulnerability of shrubs to spring freezing along elevational gradients and snow microhabitats by modelling the past frequency of spring freezing events. We sampled biomass and measured the size of Salix herbacea, Vaccinium myrtillus, Vaccinium uliginosum and Loiseleuria procumbens in late spring. Leaves were exposed to freezing temperatures to determine the temperature at which 50% of specimens are killed for each species and sampling site. By linking site snowmelt and temperatures to long-term climate measurements, we extrapolated the frequency of spring freezing events at each elevation, snow microhabitat and per species over 37 years. Snowmelt timing was significantly driven by microhabitat effects, but was independent of elevation. Shrub growth was neither enhanced nor reduced by earlier snowmelt, but decreased with elevation. Freezing resistance was strongly species dependent, and did not differ along the elevation or snowmelt gradient. Microclimate extrapolation suggested that potentially lethal freezing events (in May and June) occurred for three of the four species examined. Freezing events never occurred on late snow beds, and increased in frequency with earlier snowmelt and higher elevation. Extrapolated freezing events showed a slight, non-significant increase over the 37-year record. We suggest that earlier snowmelt does not enhance growth in four dominant alpine shrubs, but increases the risk of lethal spring freezing exposure for less freezing-resistant species.

Controlled crystallization of the lipophilic drug fenofibrate during freeze-drying: elucidation of the mechanism by in-line Raman spectroscopy.

PubMed

de Waard, Hans; De Beer, Thomas; Hinrichs, Wouter L J; Vervaet, Chris; Remon, Jean-Paul; Frijlink, Henderik W

2010-12-01

We developed a novel process, "controlled crystallization during freeze-drying" to produce drug nanocrystals of poorly water-soluble drugs. This process involves freeze-drying at a relatively high temperature of a drug and a matrix material from a mixture of tertiary butyl alcohol and water, resulting in drug nanocrystals incorporated in a matrix. The aim of this study was to elucidate the mechanisms that determine the size of the drug crystals. Fenofibrate was used as a model lipophilic drug. To monitor the crystallization during freeze-drying, a Raman probe was placed just above the sample in the freeze-dryer. These in-line Raman spectroscopy measurements clearly revealed when the different components crystallized during freeze-drying. The solvents crystallized only during the freezing step, while the solutes only crystallized after the temperature was increased, but before drying started. Although the solutes crystallized only after the freezing step, both the freezing rate and the shelf temperature were critical parameters that determined the final crystal size. At a higher freezing rate, smaller interstitial spaces containing the freeze-concentrated fraction were formed, resulting in smaller drug crystals (based on dissolution data). On the other hand, when the solutes crystallized at a lower shelf temperature, the degree of supersaturation is higher, resulting in a higher nucleation rate and consequently more and therefore smaller crystals. In conclusion, for the model drug fenofibrate, a high freezing rate and a relatively low crystallization temperature resulted in the smallest crystals and therefore the highest dissolution rate.

Effect of three cueing devices for people with Parkinson's disease with gait initiation difficulties.

PubMed

McCandless, Paula J; Evans, Brenda J; Janssen, Jessie; Selfe, James; Churchill, Andrew; Richards, Jim

2016-02-01

Freezing of gait (FOG) remains one of the most common debilitating aspects of Parkinson's disease and has been linked to injuries, falls and reduced quality of life. Although commercially available portable cueing devices exist claiming to assist with overcoming freezing; their immediate effectiveness in overcoming gait initiation failure is currently unknown. This study investigated the effects of three different types of cueing device in people with Parkinson's disease who experience freezing. Twenty participants with idiopathic Parkinson's disease who experienced freezing during gait but who were able to walk short distances indoors independently were recruited. At least three attempts at gait initiation were recorded using a 10 camera Qualisys motion analysis system and four force platforms. Test conditions were; Laser Cane, sound metronome, vibrating metronome, walking stick and no intervention. During testing 12 of the 20 participants had freezing episodes, from these participants 100 freezing and 91 non-freezing trials were recorded. Clear differences in the movement patterns were seen between freezing and non-freezing episodes. The Laser Cane was most effective cueing device at improving the forwards/backwards and side to side movement and had the least number of freezing episodes. The walking stick also showed significant improvements compared to the other conditions. The vibration metronome appeared to disrupt movement compared to the sound metronome at the same beat frequency. This study identified differences in the movement patterns between freezing episodes and non-freezing episodes, and identified immediate improvements during gait initiation when using the Laser Cane over the other interventions. Copyright © 2015. Published by Elsevier B.V.

Role of glucose-6-phosphate dehydrogenase in freezing-induced freezing resistance of Populus suaveolens.

PubMed

Lin, Shan-Zhi; Zhang, Zhi-Yi; Liu, Wen-Feng; Lin, Yuan-Zhen; Zhang, Qian; Zhu, Bao-Qing

2005-02-01

To explore the role of glucose-6-phosphate dehydrogenase (G6PDH, EC 1.1.1.49) in the enhancement of freezing resistance induced by freezing acclimation, G6PDH was purified from the leaves of 8-week-old Populus suaveolens cuttings. The G6PDH activity in the absence or the presence of reduced dithiothreitol (DTT(red)) were determined, and the changes in superoxide dismutase (SOD), peroxides (POD) and cytosolic G6PDH activities, malondial-dehyde (MDA) content as well as freezing resistance (expressed as LT(50)) of P. suaveolens cuttings during freezing acclimation at -20 degrees C were investigated. The results showed that the purified G6PDH was probably located in the cytosol of P. suaveolens. Freezing acclimation increased the activities of SOD, POD and cytosolic G6PDH, and decreased the MDA content and LT(50) of cuttings, while 2 d of de-acclimation at 25 degrees C resulted in a decrease in SOD, POD and cytosolic G6PDH activities, and caused an increase in MDA content and LT(50). The change in cytosolic G6PDH activity was found to be closely correlated to the levels of SOD, POD and MDA, and to the degree of freezing resistance of cuttings during freezing acclimation. It is suggested that the enhancement of freezing resistance of cuttings induced by freezing acclimation is related to the distinct increase in cytosolic G6PDH activity, which may be involved in the activation of SOD and POD, and the induction of freezing resistance of cuttings.

Differential freezing resistance and photoprotection in C3 and C4 eudicots and grasses

PubMed Central

Liu, Mei-Zhen; Osborne, Colin P.

2013-01-01

Globally, C4 plants dominate hot, open environments, but this general pattern is underpinned by important differences in the biogeography of C4 lineages. In particular, the species richness of C4 Poaceae (grasses) increases strongly with increasing temperature, whereas that of the major C4 eudicot group Chenopodiaceae correlates positively with aridity. Freezing tolerance is a crucial determinant of biogeographical relationships with temperature and is mediated by photodamage and cellular disruption by desiccation, but little is known about differences between C4 families. This study hypothesized that there is a greater risk of freezing damage via these mechanisms in C4 Poaceae than Chenopodiaceae, that freezing protection differs between the taxonomic groups, and that freezing tolerance of species is linked to arid habitat preference. Chlorophyll fluorescence, water relations, and freezing injury were compared in four C3 and six C4 species of Poaceae and Chenopodiaceae from the same Mongolian flora. Contrary to expectations, freezing-induced leaf mortality and photodamage were lower in Poaceae than Chenopodiaceae species, and unrelated to photosynthetic pathway. The freezing resistance of Poaceae species resulted from constitutive protection and cold acclimation and an ability to protect the photosynthetic apparatus from photodamage. Freezing protection was associated with low osmotic potential and low tissue elasticity, and freezing damage was accompanied by electrolyte leakage, consistent with cell-membrane disruption by ice. Both Chenopodiaceae and Poaceae had the potential to develop cold acclimation and withstand freezing during the growing season, which conflicted with the hypothesis. Instead, freezing tolerance was more closely associated with life history and ecological preference in these Mongolian species. PMID:23599273

Embolism Formation during Freezing in the Wood of Picea abies1

PubMed Central

Mayr, Stefan; Cochard, Hervé; Améglio, Thierry; Kikuta, Silvia B.

2007-01-01

Freeze-thaw events can cause embolism in plant xylem. According to classical theory, gas bubbles are formed during freezing and expand during thawing. Conifers have proved to be very resistant to freeze-thaw induced embolism, because bubbles in tracheids are small and redissolve during thawing. In contrast, increasing embolism rates upon consecutive freeze-thaw events were observed that cannot be explained by the classical mechanism. In this study, embolism formation during freeze-thaw events was analyzed via ultrasonic and Cryo-scanning electron microscope techniques. Twigs of Picea abies L. Karst. were subjected to up to 120 freeze-thaw cycles during which ultrasonic acoustic emissions, xylem temperature, and diameter variations were registered. In addition, the extent and cross-sectional pattern of embolism were analyzed with staining experiments and Cryo-scanning electron microscope observations. Embolism increased with the number of freeze-thaw events in twigs previously dehydrated to a water potential of −2.8 MPa. In these twigs, acoustic emissions were registered, while saturated twigs showed low, and totally dehydrated twigs showed no, acoustic activity. Acoustic emissions were detected only during the freezing process. This means that embolism was formed during freezing, which is in contradiction to the classical theory of freeze-thaw induced embolism. The clustered pattern of embolized tracheids in cross sections indicates that air spread from a dysfunctional tracheid to adjacent functional ones. We hypothesize that the low water potential of the growing ice front led to a decrease of the potential in nearby tracheids. This may result in freezing-induced air seeding. PMID:17041033

Contact freezing of supercooled cloud droplets on collision with mineral dust particles: effect of particle size

NASA Astrophysics Data System (ADS)

Hoffmann, Nadine; Duft, Denis; Kiselev, Alexei; Leisner, Thomas

2013-04-01

The contact freezing of supercooled cloud droplets is one of the potentially important and the least investigated heterogeneous mechanism of ice formation in the tropospheric clouds [1]. On the time scales of cloud lifetime the freezing of supercooled water droplets via contact mechanism may occur at higher temperature compared to the same IN immersed in the droplet. However, the laboratory experiments of contact freezing are very challenging due to the number of factors affecting the probability of ice formation. In our experiment we study single water droplets freely levitated in the laminar flow of mineral dust particles acting as the contact freezing nuclei. By repeating the freezing experiment sufficient number of times we are able to reproduce statistical freezing behavior of large ensembles of supercooled droplets and measure the average rate of freezing events. We show that the rate of freezing at given temperature is governed only by the rate of droplet -particle collision and by the properties of the contact ice nuclei. In this contribution we investigate the relationship between the freezing probability and the size of mineral dust particle (represented by illite) and show that their IN efficiency scales with the particle size. Based on this observation, we discuss the similarity between the freezing of supercooled water droplets in immersion and contact modes and possible mechanisms of apparent enhancement of the contact freezing efficiency. [1] - K.C. Young, The role of contact nucleation in ice phase initiation in clouds, Journal of the Atmospheric Sciences 31, 1974

Ice nucleation temperature influences recovery of activity of a model protein after freeze drying.

PubMed

Cochran, Teresa; Nail, Steven L

2009-09-01

The objective of this study was to determine whether a relationship exists between ice nucleation temperature and recovery of activity of a model protein, lactate dehydrogenase, after freeze drying. Aqueous buffer systems containing 50 microg/mL of protein were frozen in vials with externally mounted thermocouples on the shelf of a freeze dryer, then freeze dried. Various methods were used to establish a wide range of ice nucleation temperatures. An inverse relationship was found between the extent of supercooling during freezing and recovery of activity in the reconstituted solution. The data are consistent with a mechanism of inactivation resulting from adsorption of protein at the ice/freeze-concentrate interface during the freezing process.

Predictive modeling of freezing and thawing of frost-susceptible soils.

DOT National Transportation Integrated Search

2015-09-01

Frost depth is an essential factor in design of various transportation infrastructures. In frost : susceptible soils, as soils freezes, water migrates through the soil voids below the freezing line : towards the freezing front and causes excessive he...

Cognitive Contributions to Freezing of Gait in Parkinson Disease: Implications for Physical Rehabilitation

PubMed Central

King, Laurie A.; Cohen, Rajal G.; Horak, Fay B.

2016-01-01

People with Parkinson disease (PD) who show freezing of gait also have dysfunction in cognitive domains that interact with mobility. Specifically, freezing of gait is associated with executive dysfunction involving response inhibition, divided attention or switching attention, and visuospatial function. The neural control impairments leading to freezing of gait have recently been attributed to higher-level, executive and attentional cortical processes involved in coordinating posture and gait rather than to lower-level, sensorimotor impairments. To date, rehabilitation for freezing of gait primarily has focused on compensatory mobility training to overcome freezing events, such as sensory cueing and voluntary step planning. Recently, a few interventions have focused on restitutive, rather than compensatory, therapy. Given the documented impairments in executive function specific to patients with PD who freeze and increasing evidence of overlap between cognitive and motor function, incorporating cognitive challenges with mobility training may have important benefits for patients with freezing of gait. Thus, a novel theoretical framework is proposed for exercise interventions that jointly address both the specific cognitive and mobility challenges of people with PD who freeze. PMID:26381808

Cognitive Contributions to Freezing of Gait in Parkinson Disease: Implications for Physical Rehabilitation.

PubMed

Peterson, Daniel S; King, Laurie A; Cohen, Rajal G; Horak, Fay B

2016-05-01

People with Parkinson disease (PD) who show freezing of gait also have dysfunction in cognitive domains that interact with mobility. Specifically, freezing of gait is associated with executive dysfunction involving response inhibition, divided attention or switching attention, and visuospatial function. The neural control impairments leading to freezing of gait have recently been attributed to higher-level, executive and attentional cortical processes involved in coordinating posture and gait rather than to lower-level, sensorimotor impairments. To date, rehabilitation for freezing of gait primarily has focused on compensatory mobility training to overcome freezing events, such as sensory cueing and voluntary step planning. Recently, a few interventions have focused on restitutive, rather than compensatory, therapy. Given the documented impairments in executive function specific to patients with PD who freeze and increasing evidence of overlap between cognitive and motor function, incorporating cognitive challenges with mobility training may have important benefits for patients with freezing of gait. Thus, a novel theoretical framework is proposed for exercise interventions that jointly address both the specific cognitive and mobility challenges of people with PD who freeze. © 2016 American Physical Therapy Association.

Representative Values of Icing-Related Variables Aloft in Freezing Rain and Freezing Drizzle

DOT National Transportation Integrated Search

1996-03-01

Radiosonde and surface observations in freezing rain (ZR) and freezing drizzle (ZL), and a limited number of aircraft measurements in ZR, have been examined for information on the magnitude and altitude dependence of meteorological variables associat...

Effects of Artificial Supercooling Followed by Slow Freezing on the Microstructure and Qualities of Pork Loin

PubMed Central

2016-01-01

This study investigated the effects of artificial supercooling followed by still air freezing (SSF) on the qualities of pork loin. The qualities of pork frozen by SSF were compared with the fresh control (CT, stored at 4℃ for 24 h), slow freezing (SAF, still air freezing) and rapid freezing (EIF, ethanol immersion freezing) treatments. Compared with no supercooling phenomena of SAF and EIF, the extent of supercooling obtained by SSF treatment was 1.4℃. Despite that SSF was conducted with the same method with SAF, application of artificial supercooling accelerated the phase transition (traverse from -0.6℃ to -5℃) from 3.07 h (SAF) to 2.23 h (SSF). The observation of a microstructure indicated that the SSF prevented tissue damage caused by ice crystallization and maintained the structural integrity. The estimated quality parameters reflected that SSF exhibited superior meat quality compared with slow freezing (SAF). SSF showed better water-holding capacity (lower thawing loss, cooking loss and expressible moisture) and tenderness than SAF, and these quality parameters of SSF were not significantly different with ultra-fast freezing treatment (EIF). Consequently, the results demonstrated that the generation of supercooling followed by conventional freezing potentially had the advantage of minimizing the quality deterioration caused by the slow freezing of meat. PMID:27857541

Automated realization of the gallium melting and triple points

NASA Astrophysics Data System (ADS)

Yan, X.; Duan, Y.; Zhang, J. T.; Wang, W.

2013-09-01

In order to improve the automation and convenience of the process involved in realizing the gallium fixed points, an automated apparatus, based on thermoelectric and heat pipe technologies, was designed and developed. This paper describes the apparatus design and procedures for freezing gallium mantles and realizing gallium melting and triple points. Also, investigations on the melting behavior of a gallium melting point cell and of gallium triple point cells were carried out while controlling the temperature outside the gallium point cells at 30 °C, 30.5 °C, 31 °C, and 31.5 °C. The obtained melting plateau curves show dentate temperature oscillations on the melting plateaus for the gallium point cells when thermal couplings occurred between the outer and inner liquid-solid interfaces. The maximum amplitude of the temperature fluctuations was about 1.5 mK. Therefore, the temperature oscillations can be used to indicate the ending of the equilibrium phase transitions. The duration and amplitude of such temperature oscillations depend on the temperature difference between the setting temperature and the gallium point temperature; the smaller the temperature difference, the longer the duration of both the melting plateaus and the temperature fluctuations.

Fundamental Technical Elements of Freeze-fracture/Freeze-etch in Biological Electron Microscopy

EPA Science Inventory

Freeze-fracture/freeze-etch describes a process whereby specimens, typically biological or nanomaterial in nature, are frozen, fractured, and replicated to generate a carbon/platinum "cast" intended for examination by transmission electron microscopy. Specimens are subjected to u...

Demonstrating Functional Equivalence of Pilot and Production Scale Freeze-Drying of BCG

PubMed Central

ten Have, R.; Reubsaet, K.; van Herpen, P.; Kersten, G.; Amorij, J.-P.

2016-01-01

Process analytical technology (PAT)-tools were used to monitor freeze-drying of Bacille Calmette-Guérin (BCG) at pilot and production scale. Among the evaluated PAT-tools, there is the novel use of the vacuum valve open/close frequency for determining the endpoint of primary drying at production scale. The duration of primary drying, the BCG survival rate, and the residual moisture content (RMC) were evaluated using two different freeze-drying protocols and were found to be independent of the freeze-dryer scale evidencing functional equivalence. The absence of an effect of the freeze-dryer scale on the process underlines the feasibility of the pilot scale freeze-dryer for further BCG freeze-drying process optimization which may be carried out using a medium without BCG. PMID:26981867

Demonstrating Functional Equivalence of Pilot and Production Scale Freeze-Drying of BCG.

PubMed

Ten Have, R; Reubsaet, K; van Herpen, P; Kersten, G; Amorij, J-P

2016-01-01

Process analytical technology (PAT)-tools were used to monitor freeze-drying of Bacille Calmette-Guérin (BCG) at pilot and production scale. Among the evaluated PAT-tools, there is the novel use of the vacuum valve open/close frequency for determining the endpoint of primary drying at production scale. The duration of primary drying, the BCG survival rate, and the residual moisture content (RMC) were evaluated using two different freeze-drying protocols and were found to be independent of the freeze-dryer scale evidencing functional equivalence. The absence of an effect of the freeze-dryer scale on the process underlines the feasibility of the pilot scale freeze-dryer for further BCG freeze-drying process optimization which may be carried out using a medium without BCG.

Research on strength attenuation law of concrete in freezing - thawing environment

NASA Astrophysics Data System (ADS)

Xiao, qianhui; Cao, zhiyuan; Li, qiang

2018-03-01

By rapid freezing and thawing method, the experiments of concrete have been 300 freeze-thaw cycles specimens in the water. The cubic compression strength value under different freeze-thaw cycles was measured. By analyzing the test results, the water-binder ratio of the concrete under freeze-thaw environments, fly ash and air entraining agent is selected dosage recommendations. The exponential attenuation prediction model and life prediction model of compression strength of concrete under freezing-thawing cycles considering the factors of water-binder ratio, fly ash content and air-entraining agent dosage were established. The model provides the basis for predicting the durability life of concrete under freezing-thawing environment. It also provides experimental basis and references for further research on concrete structures with antifreeze requirements.

Experimental research on durability of recycled aggregate concrete under freeze- thaw cycles

NASA Astrophysics Data System (ADS)

Cheng, Yanqiu; Shang, Xiaoyu; Zhang, Youjia

2017-07-01

The freeze-thaw durability of recycled aggregate concrete has significance for the concrete buildings in the cold region. In this paper, the rapid freezing and thawing cycles experience on recycle aggregate concrete was conducted to study on the effects of recycle aggregate amount, water-binder ratio and fly ash on freeze-thaw durability of recycle aggregate concrete. The results indicates that recycle aggregate amount makes the significant influence on the freeze-thaw durability. With the increase of recycled aggregates amount, the freeze-thaw resistance for recycled aggregate concrete decreases. Recycled aggregate concrete with lower water cement ratio demonstrates better performance of freeze-thaw durability. It is advised that the amount of fly ash is less than 30% for admixture of recycled aggregates in the cold region.

MAL62 overexpression and NTH1 deletion enhance the freezing tolerance and fermentation capacity of the baker's yeast in lean dough.

PubMed

Sun, Xi; Zhang, Cui-Ying; Wu, Ming-Yue; Fan, Zhi-Hua; Liu, Shan-Na; Zhu, Wen-Bi; Xiao, Dong-Guang

2016-04-04

Trehalose is related to several types of stress responses, especially freezing response in baker's yeast (Saccharomyces cerevisiae). It is desirable to manipulate trehalose-related genes to create yeast strains that better tolerate freezing-thaw stress with improved fermentation capacity, which are in high demand in the baking industry. The strain overexpressing MAL62 gene showed increased trehalose content and cell viability after prefermention-freezing and long-term frozen. Deletion of NTH1 in combination of MAL62 overexpression further strengthens freezing tolerance and improves the leavening ability after freezing-thaw stress. The mutants of the industrial baker's yeast with enhanced freezing tolerance and leavening ability in lean dough were developed by genetic engineering. These strains had excellent potential industrial applications.

Freeze/Thaw-Induced Embolism: Probability of Critical Bubble Formation Depends on Speed of Ice Formation

DOE PAGES

Sevanto, Sanna; Holbrook, N. Michele; Ball, Marilyn C.

2012-06-06

Bubble formation in the conduits of woody plants sets a challenge for uninterrupted water transportation from the soil up to the canopy. Freezing and thawing of stems has been shown to increase the number of air-filled (embolized) conduits, especially in trees with large conduit diameters. Despite numerous experimental studies, the mechanisms leading to bubble formation during freezing have not been addressed theoretically. We used classical nucleation theory and fluid mechanics to show which mechanisms are most likely to be responsible for bubble formation during freezing and what parameters determine the likelihood of the process. Our results confirm the common assumptionmore » that bubble formation during freezing is most likely due to gas segregation by ice. If xylem conduit walls are not permeable to the salts expelled by ice during the freezing process, osmotic pressures high enough for air seeding could be created. The build-up rate of segregated solutes in front of the ice-water interface depends equally on conduit diameter and freezing velocity. Therefore, bubble formation probability depends on these variables. The dependence of bubble formation probability on freezing velocity means that the experimental results obtained for cavitation threshold conduit diameters during freeze/thaw cycles depend on the experimental setup; namely sample size and cooling rate. The velocity dependence also suggests that to avoid bubble formation during freezing trees should have narrow conduits where freezing is likely to be fast (e.g., branches or outermost layer of the xylem). Avoidance of bubble formation during freezing could thus be one piece of the explanation why xylem conduit size of temperate and boreal zone trees varies quite systematically.« less

Optimizing the Protocol for Pulmonary Cryoablation: A Comparison of a Dual- and Triple-Freeze Protocol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hinshaw, J. Louis, E-mail: jhinshaw@uwhealth.or; Littrup, Peter J.; Durick, Nathan

2010-12-15

The purpose of this study was to compare a double freeze-thaw protocol to a triple freeze-thaw protocol for pulmonary cryoablation utilizing an in vivo porcine lung model. A total of 18 cryoablations were performed in normal porcine lung utilizing percutaneous technique with 9 each in a double- (10-5-10) and triple-freeze (3-3-7-7-5) protocol. Serial noncontrast CT images were obtained during the ablation. CT imaging findings and pathology were reviewed. No imaging changes were identified during the initial freeze cycle with either protocol. However, during the first thaw cycle, a region of ground glass opacity developed around the probe with both protocols.more » Because the initial freeze was shorter with the triple freeze-thaw protocol, the imaging findings were apparent sooner with this protocol (6 vs. 13 min). Also, despite a shorter total freeze time (15 vs. 20 min), the ablation zone identified with the triple freeze-thaw protocol was not significantly different from the double freeze-thaw protocol (mean diameter: 1.67 {+-} 0.41 cm vs. 1.66 {+-} 0.21 cm, P = 0.77; area: 2.1 {+-} 0.48 cm{sup 2} vs. 1.99 {+-} 0.62 cm{sup 2}, P = 0.7; and circularity: 0.95 {+-} 0.04 vs. 0.96 {+-} 0.03, P = 0.62, respectively). This study suggests that there may be several advantages of a triple freeze-thaw protocol for pulmonary cryoablation, including earlier identification of the imaging findings associated with the ablation, the promise of a shorter procedure time or larger zones of ablation, and theoretically, more effective cytotoxicity related to the additional freeze-thaw cycle.« less

Rapid freezing without cooling equilibration in canine sperm.

PubMed

Kim, Suhee; Lee, Yongcheol; Yang, Honghyun; Kim, Yong-Jun

2012-01-01

The aim of this study was to develop a rapid method of canine semen freezing without cooling equilibration using treatment with different cryoprotectant agents (CPAs) and freezing in liquid nitrogen (LN(2)) vapor in a 0.5-mL straw via modifying vitrification. Ejaculates from eight beagle dogs were frozen with different CPAs (CPA-free, 5% glycerol, 5% ethylene glycol, and 10% ethylene glycol) and freezing times (direct plunging into LN(2) or freezing for 1, 2, 3, or 10 min in LN(2) vapor before plunging into LN(2)). Frozen-thawed sperm were evaluated for motility, viability, normal morphology, and plasma- and acrosome-membrane integrities. The 5% glycerol treatment resulted in improved sperm motility, plasma-membrane integrity and acrosome-membrane integrity (P<0.05). Freezing in LN(2) vapor showed improved sperm motility, viability, and plasma membrane integrity (P<0.05), and freezing for more than 2 min in LN(2) vapor increased acrosome-membrane integrity compared with direct plunging into LN(2) (P<0.05). The direct plunging into LN(2) showed no motile sperm. However, freezing for more than 2 min in LN(2) vapor increased the total abnormalities compared to direct plunging into LN(2) (P<0.05). In conclusion, use of 5% glycerol and freezing in LN(2) vapor were essential for the rapid freezing of canine sperm without cooling equilibration. In particular, holding for 2 min in LN(2) vapor was sufficient to yield successful rapid freezing. This rapid freezing method is simple and effective in canine sperm and would be helpful to offer information for trial of vitrification in large volumes of canine sperm. Copyright © 2012 Elsevier B.V. All rights reserved.

Freeze/Thaw-induced embolism: probability of critical bubble formation depends on speed of ice formation.

PubMed

Sevanto, Sanna; Holbrook, N Michele; Ball, Marilyn C

2012-01-01

Bubble formation in the conduits of woody plants sets a challenge for uninterrupted water transportation from the soil up to the canopy. Freezing and thawing of stems has been shown to increase the number of air-filled (embolized) conduits, especially in trees with large conduit diameters. Despite numerous experimental studies, the mechanisms leading to bubble formation during freezing have not been addressed theoretically. We used classical nucleation theory and fluid mechanics to show which mechanisms are most likely to be responsible for bubble formation during freezing and what parameters determine the likelihood of the process. Our results confirm the common assumption that bubble formation during freezing is most likely due to gas segregation by ice. If xylem conduit walls are not permeable to the salts expelled by ice during the freezing process, osmotic pressures high enough for air seeding could be created. The build-up rate of segregated solutes in front of the ice-water interface depends equally on conduit diameter and freezing velocity. Therefore, bubble formation probability depends on these variables. The dependence of bubble formation probability on freezing velocity means that the experimental results obtained for cavitation threshold conduit diameters during freeze/thaw cycles depend on the experimental setup; namely sample size and cooling rate. The velocity dependence also suggests that to avoid bubble formation during freezing trees should have narrow conduits where freezing is likely to be fast (e.g., branches or outermost layer of the xylem). Avoidance of bubble formation during freezing could thus be one piece of the explanation why xylem conduit size of temperate and boreal zone trees varies quite systematically.

Mutagenic effect of freezing on mitochondrial DNA of Saccharomyces cerevisiae.

PubMed

Stoycheva, T; Venkov, P; Tsvetkov, Ts

2007-06-01

Although suggested in some studies, the mutagenic effect of freezing has not been proved by induction and isolation of mutants. Using a well-defined genetic model, we supply in this communication evidence for the mutagenic effect of freezing on mitochondrial DNA (mtDNA) of the yeast Saccharomyces cerevisiae. The cooling for 2 h at +4 degrees C, followed by freezing for 1 h at -10 degrees C and 16 h at -20 degrees C resulted in induction of respiratory mutations. The immediate freezing in liquid nitrogen was without mutagenic effect. The study of the stepwise procedure showed that the induction of respiratory mutants takes place during the freezing at -10 and -20 degrees C of cells pre-cooled at +4 degrees C. The genetic crosses of freeze-induced mutants evidenced their mitochondrial rho- origin. The freeze-induced rho- mutants are most likely free of simultaneous nuclear mutations. The extracellular presence of cryoprotectants did not prevent the mutagenic effect of freezing while accumulation of cryoprotectors inside cells completely escaped mtDNA from cryodamage. Although the results obtained favor the notion that the mutagenic effect of freezing on yeast mtDNA is due to formation and growth of intracellular ice crystals, other reasons, such as impairment of mtDNA replication or elevated levels of ROS production are discussed as possible explanations of the mutagenic effect of freezing. It is concluded that: (i) freezing can be used as a method for isolation of mitochondrial mutants in S. cerevisiae and (ii) given the substantial development in cryopreservation of cells and tissues, special precautions should be made to avoid mtDNA damage during the cryopreservation procedures.

SENSITIVE TO FREEZING2 Aids in Resilience to Salt and Drought in Freezing-Sensitive Tomato

DOE PAGES

Wang, Kun; Hersh, Hope Lynn; Benning, Christoph

2016-09-06

SENSITIVE TO FREEZING2 (SFR2) is crucial for protecting chloroplast membranes following freezing in Arabidopsis (Arabidopsis thaliana). It has been shown that SFR2 homologs are present in all land plants, including freezing-sensitive species, raising the question of SFR2 function beyond freezing tolerance. Similar to freezing, salt and drought can cause dehydration. Thus, it is hypothesized that in freezing-sensitive plants SFR2 may play roles in their resilience to salt or drought. To test this hypothesis, SlSFR2 RNAi lines were generated in the cold/freezing-sensitive species tomato (Solanum lycopersicum [M82 cv]). Hypersensitivity to salt and drought of SlSFR2-RNAi lines was observed. Higher tolerance ofmore » wild-type tomatoes was correlated with the production of trigalactosyldiacylglycerol, a product of SFR2 activity. Tomato SFR2 in vitro activity is Mg 2+-dependent and its optimal pH is 7.5, similar to that of Arabidopsis SFR2, but the specific activity of tomato SFR2 in vitro is almost double that of Arabidopsis SFR2. When salt and drought stress were applied to Arabidopsis, no conditions could be identified at which SFR2 was induced prior to irreversibly impacting plant growth, suggesting that SFR2 protects Arabidopsis primarily against freezing. Discovery of tomato SFR2 function in drought and salt resilience provides further insights into general membrane lipid remodeling-based stress tolerance mechanisms and together with protection against freezing in freezing-resistant plants such as Arabidopsis, it adds lipid remodeling as a possible target for the engineering of abiotic stress-resilient crops.« less

SENSITIVE TO FREEZING2 Aids in Resilience to Salt and Drought in Freezing-Sensitive Tomato

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Kun; Hersh, Hope Lynn; Benning, Christoph

SENSITIVE TO FREEZING2 (SFR2) is crucial for protecting chloroplast membranes following freezing in Arabidopsis (Arabidopsis thaliana). It has been shown that SFR2 homologs are present in all land plants, including freezing-sensitive species, raising the question of SFR2 function beyond freezing tolerance. Similar to freezing, salt and drought can cause dehydration. Thus, it is hypothesized that in freezing-sensitive plants SFR2 may play roles in their resilience to salt or drought. To test this hypothesis, SlSFR2 RNAi lines were generated in the cold/freezing-sensitive species tomato (Solanum lycopersicum [M82 cv]). Hypersensitivity to salt and drought of SlSFR2-RNAi lines was observed. Higher tolerance ofmore » wild-type tomatoes was correlated with the production of trigalactosyldiacylglycerol, a product of SFR2 activity. Tomato SFR2 in vitro activity is Mg 2+-dependent and its optimal pH is 7.5, similar to that of Arabidopsis SFR2, but the specific activity of tomato SFR2 in vitro is almost double that of Arabidopsis SFR2. When salt and drought stress were applied to Arabidopsis, no conditions could be identified at which SFR2 was induced prior to irreversibly impacting plant growth, suggesting that SFR2 protects Arabidopsis primarily against freezing. Discovery of tomato SFR2 function in drought and salt resilience provides further insights into general membrane lipid remodeling-based stress tolerance mechanisms and together with protection against freezing in freezing-resistant plants such as Arabidopsis, it adds lipid remodeling as a possible target for the engineering of abiotic stress-resilient crops.« less

SENSITIVE TO FREEZING2 Aids in Resilience to Salt and Drought in Freezing-Sensitive Tomato1[OPEN

PubMed Central

Hersh, Hope Lynn

2016-01-01

SENSITIVE TO FREEZING2 (SFR2) is crucial for protecting chloroplast membranes following freezing in Arabidopsis (Arabidopsis thaliana). It has been shown that SFR2 homologs are present in all land plants, including freezing-sensitive species, raising the question of SFR2 function beyond freezing tolerance. Similar to freezing, salt and drought can cause dehydration. Thus, it is hypothesized that in freezing-sensitive plants SFR2 may play roles in their resilience to salt or drought. To test this hypothesis, SlSFR2 RNAi lines were generated in the cold/freezing-sensitive species tomato (Solanum lycopersicum [M82 cv]). Hypersensitivity to salt and drought of SlSFR2-RNAi lines was observed. Higher tolerance of wild-type tomatoes was correlated with the production of trigalactosyldiacylglycerol, a product of SFR2 activity. Tomato SFR2 in vitro activity is Mg2+-dependent and its optimal pH is 7.5, similar to that of Arabidopsis SFR2, but the specific activity of tomato SFR2 in vitro is almost double that of Arabidopsis SFR2. When salt and drought stress were applied to Arabidopsis, no conditions could be identified at which SFR2 was induced prior to irreversibly impacting plant growth, suggesting that SFR2 protects Arabidopsis primarily against freezing. Discovery of tomato SFR2 function in drought and salt resilience provides further insights into general membrane lipid remodeling-based stress tolerance mechanisms and together with protection against freezing in freezing-resistant plants such as Arabidopsis, it adds lipid remodeling as a possible target for the engineering of abiotic stress-resilient crops. PMID:27600812

Arginine and proline applied as food additives stimulate high freeze tolerance in larvae of Drosophila melanogaster.

PubMed

Koštál, Vladimír; Korbelová, Jaroslava; Poupardin, Rodolphe; Moos, Martin; Šimek, Petr

2016-08-01

The fruit fly Drosophila melanogaster is an insect of tropical origin. Its larval stage is evolutionarily adapted for rapid growth and development under warm conditions and shows high sensitivity to cold. In this study, we further developed an optimal acclimation and freezing protocol that significantly improves larval freeze tolerance (an ability to survive at -5°C when most of the freezable fraction of water is converted to ice). Using the optimal protocol, freeze survival to adult stage increased from 0.7% to 12.6% in the larvae fed standard diet (agar, sugar, yeast, cornmeal). Next, we fed the larvae diets augmented with 31 different amino compounds, administered in different concentrations, and observed their effects on larval metabolomic composition, viability, rate of development and freeze tolerance. While some diet additives were toxic, others showed positive effects on freeze tolerance. Statistical correlation revealed tight association between high freeze tolerance and high levels of amino compounds involved in arginine and proline metabolism. Proline- and arginine-augmented diets showed the highest potential, improving freeze survival to 42.1% and 50.6%, respectively. Two plausible mechanisms by which high concentrations of proline and arginine might stimulate high freeze tolerance are discussed: (i) proline, probably in combination with trehalose, could reduce partial unfolding of proteins and prevent membrane fusions in the larvae exposed to thermal stress (prior to freezing) or during freeze dehydration; (ii) both arginine and proline are exceptional among amino compounds in their ability to form supramolecular aggregates which probably bind partially unfolded proteins and inhibit their aggregation under increasing freeze dehydration. © 2016. Published by The Company of Biologists Ltd.

Aquatic toxicity of airfield-pavement deicer materials and implications for airport runoff

USGS Publications Warehouse

Corsi, S.R.; Geis, S.W.; Bowman, G.; Failey, G.G.; Rutter, T.D.

2009-01-01

Concentrations of airfield-pavement deicer materials (PDM) in a study of airport runoff often exceeded levels of concern regarding aquatic toxicity. Toxicity tests on Vibrio fischeri, Pimephales promelas, Ceriodaphnia dubia, and Pseudokirchneriella subcapitata (commonly known as Selenastrum capricornutum) were performed with potassium acetate (K-Ac) PDM, sodium formate (Na-For) PDM, and with freezing- point depressants (K-Ac and Na-For). Results indicate that toxicity in PDM is driven by the freezing-point depressants in all tests except the Vibrio fisheri test for Na-For PDM which is influenced by an additive. Acute toxicity end points for different organisms ranged from 298 to 6560 mg/L (as acetate) for K-Ac PDM and from 1780 to 4130 mg/L (as formate) for Na- For PDM. Chronic toxicity end points ranged from 19.9 to 336 mg/L (as acetate) for K-Ac PDM and from 584 to 1670 mg/L (as formate) for Na-For PDM. Sample results from outfalls at General Mitchell International Airport in Milwaukee, Wl (GMIA) indicated that 40% of samples had concentrations greater than the aquatic-life benchmark for K-Ac PDM. K-Ac has replaced urea during the 1990s as the most widely used PDM at GMIA and in the United States. Results of ammonia samples from airport outfalls during periods when urea-based PDM was used at GMIA indicated that41% of samples had concentrations exceeding the U.S. Environmental Protection Agency (USEPA) 1 -h water-quality criterion. The USEPA 1-h water-quality criterion for chloride was exceeded in 68% of samples collected in the receiving stream, a result of road-salt runoff from urban influence near the airport. Results demonstrate that PDM must be considered to comprehensively evaluate the impact of chemical deicers on aquatic toxicity in water containing airport runoff. ?? 2009 American Chemical Society.

Evidence of cyclical light/dark-regulated expression of freezing tolerance in young winter wheat plants.

PubMed

Skinner, Daniel Z; Bellinger, Brian; Hiscox, William; Helms, Gregory L

2018-01-01

The ability of winter wheat (Triticum aestivum L.) plants to develop freezing tolerance through cold acclimation is a complex rait that responds to many environmental cues including day length and temperature. A large part of the freezing tolerance is conditioned by the C-repeat binding factor (CBF) gene regulon. We investigated whether the level of freezing tolerance of 12 winter wheat lines varied throughout the day and night in plants grown under a constant low temperature and a 12-hour photoperiod. Freezing tolerance was significantly greater (P<0.0001) when exposure to subfreezing temperatures began at the midpoint of the light period, or the midpoint of the dark period, compared to the end of either period, with an average of 21.3% improvement in survival. Thus, freezing survival was related to the photoperiod, but cycled from low, to high, to low within each 12-hour light period and within each 12-hour dark period, indicating ultradian cyclic variation of freezing tolerance. Quantitative real-time PCR analysis of expression levels of CBF genes 14 and 15 indicated that expression of these two genes also varied cyclically, but essentially 180° out of phase with each other. Proton nuclear magnetic resonance analysis (1H-NMR) showed that the chemical composition of the wheat plants' cellular fluid varied diurnally, with consistent separation of the light and dark phases of growth. A compound identified as glutamine was consistently found in greater concentration in a strongly freezing-tolerant wheat line, compared to moderately and poorly freezing-tolerant lines. The glutamine also varied in ultradian fashion in the freezing-tolerant wheat line, consistent with the ultradian variation in freezing tolerance, but did not vary in the less-tolerant lines. These results suggest at least two distinct signaling pathways, one conditioning freezing tolerance in the light, and one conditioning freezing tolerance in the dark; both are at least partially under the control of the CBF regulon.

Comparison of Cryopreserved Human Sperm between Ultra Rapid Freezing and Slow Programmable Freezing: Effect on Motility, Morphology and DNA Integrity.

PubMed

Tongdee, Pattama; Sukprasert, Matchuporn; Satirapod, Chonticha; Wongkularb, Anna; Choktanasiri, Wicham

2015-05-01

Cryopreservation of sperm is common methods to preserve male fertility. Sperm freezing, suggest slow programmable freezing caused lower change of sperm morphology than sperm freezing in vapor of liquid nitrogen. Ultra rapid freezing is easy to be worked on, less time, low cost and does not need high experience. To compare the effect on sperm motility, morphology and DNA integrity of post-thawed sperm after ultra rapid freezing and slow programmable freezing methods. Experimental study at laboratory of infertility unit, Department of Obstetrics and Gynecology, Faculty of Medicine Ramathibodi Hospital. Thirty-seven semen samples with normal semen analysis according to World Health Organization (WHO) 1999 [normal sperm volume ( 2 ml) and normal sperm concentration (≥ 20 x10(6)/ml) and sperm motility (≥ 50%)]. Semen samples were washed. Then each semen sample was divided into six cryovials. Two cryovials, 0.5 ml each, were cryopreserved by slow programmable freezing. Four 0.25 ml containing cryovials, were cryopreserved by ultra rapidfreezing method. After cryopreservationfor 1 month, thawedprocess was carried out at room temperature. Main outcomes are sperm motility was determined by Computer-Assisted Semen Analysis (CASA), sperm morphology was determined by eosin-methylene blue staining and sperm DNA integrity was assessed by TUNEL assay. Sperm motility was reduced significantly by both methods, from 70.4 (9.0)% to 29.1 (12.3)% in slowprogrammable freezing and to 19.7 (9.8)% in ultra rapid freezing (p < 0.05). Sperm motility decreased significantly more by ultra rapid freezing (p < 0.001). The percentage of normal sperm morphology and DNA integrity were also reduced significantly by both methods. However, no significant difference between the two methods was found (p > 0.05). Cryopreservation of human sperm for 1 month significantly decreased sperm motility, morphology and DNA integrity in both methods. However sperm motility was decreased more by ultra rapid freezing.

A study of the impact of freezing on the lyophilization of a concentrated formulation with a high fill depth.

PubMed

Liu, Jinsong; Viverette, Todd; Virgin, Marlin; Anderson, Mitch; Paresh, Dalal

2005-01-01

The objective of this study was to evaluate the impact of freezing on the lyophilization of a concentrated formulation with a high fill depth. A model system consisting of a 15-mL fill of 15% (w/w) sulfobutylether 7-beta-cyclodextrin (SBECD) solution in a 30-mL vial was selected for this study. Various freezing methods including single-step freezing, two-step freezing with a super-cooling holding, annealing, vacuum-induced freezing, changing ice habit using tert-butyl-alcohol (TBA), ice nucleation with silver iodide (AgI), as well as combinations of some of the methods, were used in the lyophilization of this model system. This work demonstrated that the freezing process had a significant impact on primary drying rate and product quality of a concentrated formulation with a high fill depth. Annealing, vacuum-induced freezing, and addition of either TBA or an ice nucleating agent (AgI) to the formulation accelerated the subsequent ice sublimation process. Two-step freezing or addition of TBA improved the product quality by eliminating vertical heterogeneity within the cake. The combination of two-step freezing in conjunction with an annealing step was shown to be a method of choice for freezing in the lyophilization of a product with a high fill depth. In addition to being an effective method of freezing, it is most applicable for scaling up. An alternative approach is to add a certain amount of TBA to the formulation, if the TBA-formulation interaction or regulatory concerns can be demonstrated as not being an issue. An evaluation of vial size performed in this study showed that although utilizing large-diameter vials to reduce the fill depth can greatly shorten the cycle time of a single batch, it will substantially decrease the product throughput in a large-scale freeze-dryer.

A freeze-stable formulation for DTwP and DTaP vaccines.

PubMed

Xue, Honggang; Yang, Bangling; Kristensen, Debra D; Chen, Dexiang

2014-01-01

Inadvertent vaccine freezing often occurs in the cold chain and may cause damage to freeze‑sensitive vaccines. Liquid vaccines that contain aluminum salt adjuvants are particularly vulnerable. Polyol cryoprotective excipients have been shown to prevent freeze damage to hepatitis B vaccine. In this study, we examined the freeze-protective effect of propylene glycol on diphtheria-tetanus-pertussis-whole-cell (DTwP) and acellular (DTaP) vaccines. Pilot lots of DTwP and DTaP formulated with 7.5% propylene glycol underwent 3 freeze-thaw treatments. The addition of propylene glycol had no impact on pH, particle size distribution, or potency of the vaccines prior to freeze-thaw treatment; the only change noted was an increase in osmolality. The potencies and the physical properties of the vaccines containing cryoprotectant were maintained after freeze-thawing and for 3 months in accelerated stability studies. The results from this study indicate that formulating vaccines with propylene glycol can protect diphtheria-tetanus-pertussis vaccines against freeze damages.

Indirect contact freeze water desalination for an ice maker machine - CFD simulation

NASA Astrophysics Data System (ADS)

Jayakody, Harith; Al-Dadah, Raya; Mahmoud, Saad

2017-11-01

To offer for potable water shortages, sea water desalination is a potential solution for the global rising demand for fresh water. The latent heat of fusion is about one-seventh the latent heat of vaporisation, thus indicating the benefit of lower energy consumption for the freeze desalination process. Limited literature is reported on computational fluid dynamics (CFD) on freeze desalination. Therefore, analysing and investigating thermodynamic processes are easily conducted by the powerful tool of CFD. A single unit of ice formation in an ice maker machine was modelled using ANSYS Fluent software three-dimensionally. Energy, species transport and solidification/melting modules were used in building the CFD model. Parametric analysis was conducted using the established CFD model to predict the effects of freezing temperature and the geometry of the ice maker machine; on ice production and the freezing time. Lower freezing temperatures allowed more ice production and faster freezing. Increasing the diameter and the length of the freezing tube enabled more ice to be produced.

Freeze-drying of tert-butyl alcohol/water cosolvent systems: effects of formulation and process variables on residual solvents.

PubMed

Wittaya-Areekul, S; Nail, S L

1998-04-01

The objective of this study was to identify significant formulation and processing variables affecting levels of tert-butyl alcohol (TBA) and isopropyl alcohol (IPA) in freeze-dried solids prepared from TBA/water cosolvent systems. The variables examined were the physical state of the solute (crystalline vs amorphous), initial TBA concentration, freezing rate, cake thickness, and the temperature and duration of secondary drying. Sucrose and glycine were used as models for noncrystallizing and crystallizing solutes, respectively. The TBA concentration above which eutectic crystallization takes place was determined by differential scanning calorimetry. Model formulations were subjected to extremes of freezing rate by either dipping in liquid nitrogen or by slowly freezing on the shelf of a freeze-dryer. Dynamics of solvent loss during secondary drying was determined by withdrawing samples as a function of time at different shelf temperatures using a thief system. On the basis of these studies, the most important determinant of residual TBA level is the physical state of the solute. Freeze-dried glycine contained very low levels of residual TBA (0.01-0.03%) regardless of freezing rate or initial TBA concentration. For freeze-dried sucrose, residual TBA levels were approximately 2 orders of magnitude higher and were significantly affected by initial TBA concentration and freezing rate. For the sucrose/TBA/water system, relatively low residual TBA levels were obtained when the initial TBA level was above the threshold concentration for eutectic crystallization of TBA, whereas samples freeze-dried from solutions containing TBA concentrations below this threshold contained significantly higher levels of TBA. Residual IPA levels increased continuously with initial concentration of TBA in the sucrose/TBA/water system. Formulations of sucrose/TBA/water which were frozen rapidly contained residual TBA levels which were approximately twice those measured in the same formulation after slow freezing and drying under the same conditions. For the sucrose/TBA/water system, the temperature and time of secondary drying had only minimal influence on residual TBA in the freeze-dried solid. At low initial TBA concentrations (2%), residual TBA increases with increased cake thickness, perhaps because of the influence of depth of fill on effective freezing rate.

Characterization of freezing precipitation events through other meteorological variables and their recent changes over Northern Extratropics

NASA Astrophysics Data System (ADS)

Groisman, P. Y.; Yin, X.; Bulygina, O.

2017-12-01

Freezing precipitation events intertwine with agriculture, recreation, energy consumption, and seasonal transportation cycles of human activities. Using supplementary synoptic reports at 1,500 long-term stations of North America and Northern Eurasia, we created climatology of freezing precipitation near the surface and found significant changes (increases) in these occurrences in the past decade at high latitudes/elevations (Groisman et al. 2016; updated). Firstly, we document narrow boundaries of near surface temperature and humidity fields when freezing precipitation events occur; these are necessary but insufficient conditions of their occurrence. Secondly, using the upper air data at the sites collocated with in situ observations of freezing events, we quantify the typical pattern of lower troposphere temperature anomalies during freezing events: At the same locations and Julian days, the presence of freezing event at the surface is associated with significantly warmer temperatures in the lower troposphere; comparison of temperatures at nearest days before and after the freezing events with days during these events also shows statistically significant positive temperature anomalies in the lower troposphere to 500 hPa (on average, +3 to 4 °C) In the days with freezing events, vertical air temperature gradients between surface and 850 hPa become less than usual with frequent inversions, when the tropospheric air is warmer than at the surface. The above features of the lower tropospheric temperature, near-surface temperature and humidity represent a combination of weather conditions conducive for precipitation, if it happens, falling in the freezing rain form. The in situ reports of freezing events at synoptic stations allow us to estimate temporary and spatial distributions of such "special weather conditions". Thus, a posteriori high probability of freezing events under these weather conditions invokes similar probabilities of freezing rain over the ungauged terrain, where we do not have special synoptic reports but can reproduce these "special weather conditions" from less sophisticated observational networks and/or reanalyses. Reference: Groisman et al. 2016: Recent changes in the frequency of freezing precipitation in North America and Northern Eurasia. Environ Res Lett 11 045007.

Cryopreservation of Iberian pig spermatozoa. Comparison of different freezing extenders based on post-thaw sperm quality.

PubMed

De Mercado, Eduardo; Rodríguez, Ana; Gómez, Emilio; Sanz, Elena

2010-03-01

The aim of this study was to evaluate the cryoprotective effect of different freezing extenders against cryopreservation injuries on Iberian boar sperm. The sperm-rich fraction was collected and pooled from six sexually mature Iberian boars, and was frozen in different extenders containing glucose, lactose or fructose as sugar source and including Orvus ES Paste only in the freezing extender-2 (Glucose; Lactose and Fructose) or in both freezing extenders (Glucose2; Lactose2 and Fructose2). During the cryopreservation process, the supernatant was removed after the centrifugation step, then was extended with freezing extender-1 for the equilibration period and with freezing extender-2 immediately before freezing. Post-thaw sperm characteristics, such as plasma membrane integrity (SYBR-14/PI), mitochondrial function (Rhodamine 123) and acrosome integrity (NAR), were monitored. Overall sperm motility and the individual kinematic parameters of motile spermatozoa (assessed by the computer-aided sperm analysis system Sperm Class Analyzer [SCA]) were recorded in the different experimental treatments. Measurements were taken at 30 and 150 min post-thaw. The state of the acrosome after thawing did not show significant differences between the freezing extenders studied. Freezing-thawing caused a significant decrease (P<0.001) in plasma membrane integrity and in mitochondrial activity in the spermatozoa frozen with Orvus ES Paste in both freezing extenders. Furthermore, spermatozoa frozen with Orvus ES Paste in both freezing extenders exhibited lower (P<0.05) motility and kinematic parameters than those frozen in the absence of Orvus ES Paste in the first freezing extender. The spermatozoa frozen with the Lactose extender and with Orvus ES Paste only in the second freezing extender showed a better evolution of the motility and kinematic characteristics (P<0.05) over time. The deterioration in post-thaw sperm motility and kinematic parameters were concurrent with reduced sperm characteristics. It can be suggested that in the Iberian pig, the beneficial effects of Orvus ES Paste during the freezing process of spermatozoa is time dependent. The analysis of different sperm characteristics such as motility, plasma membrane integrity and mitochondrial function, determined that the extenders studied in the present experiment affected the quality of frozen-thawed semen in Iberian boar.

Perspective: Surface freezing in water: A nexus of experiments and simulations

NASA Astrophysics Data System (ADS)

Haji-Akbari, Amir; Debenedetti, Pablo G.

2017-08-01

Surface freezing is a phenomenon in which crystallization is enhanced at a vapor-liquid interface. In some systems, such as n-alkanes, this enhancement is dramatic and results in the formation of a crystalline layer at the free interface even at temperatures slightly above the equilibrium bulk freezing temperature. There are, however, systems in which the enhancement is purely kinetic and only involves faster nucleation at or near the interface. The first, thermodynamic, type of surface freezing is easier to confirm in experiments, requiring only the verification of the existence of crystalline order at the interface. The second, kinetic, type of surface freezing is far more difficult to prove experimentally. One material that is suspected of undergoing the second type of surface freezing is liquid water. Despite strong indications that the freezing of liquid water is kinetically enhanced at vapor-liquid interfaces, the findings are far from conclusive, and the topic remains controversial. In this perspective, we present a simple thermodynamic framework to understand conceptually and distinguish these two types of surface freezing. We then briefly survey fifteen years of experimental and computational work aimed at elucidating the surface freezing conundrum in water.

Three-Dimensional Microstructure of Biological Tissues during Freezing and Thawing

NASA Astrophysics Data System (ADS)

Ishiguro, Hiroshi; Horimizu, Takashi; Kataori, Akinobu; Kajigaya, Hiroshi

Three-dimensional behavior of ice crystals and cells during the freezing and thawing of biological tissues was investigated microscopically in real time by using a confocal laser scanning microscope(CLSM) and a fluorescent dye, acridine orange (AO). Fresh tender meat (2nd pectoral muscles) of chicken was stained with the AO in physiological saline to distinguish ice crystals and cells by their different colors, and then frozen and thawed under two different thermal protocols: a) slow-cooling and rapid-warming and b) rapid-cooling and rapid-warming. The CLSM noninvasively produced optical tomograms of the tissues to clarify the pattern of freezing, morphology of ice crystals in the tissues, and the interaction between ice crystals and cells. Also, the tissues were morphologically investigated by pathological means after the freezing and thawing. Typical freezing pattern during the slow-cooling was extracellular-freezing, and those during the rapid-cooling were extracellular-freezing and intracellular freezing with a lot of fine ice crystals in the cells. Cracks caused by the extracellular and intracellular ice crystals remained in the muscle tissues after the thawing. The results obtained by using the CLSM/dye method were consistent with pathologically morphological changes in the tissues through freezing and thawing.

Cold tolerance and freeze-induced glucose accumulation in three terrestrial slugs.

PubMed

Slotsbo, Stine; Hansen, Lars Monrad; Jordaens, Kurt; Backeljau, Thierry; Malmendal, Anders; Nielsen, Niels Chr; Holmstrup, Martin

2012-04-01

Cold tolerance and metabolic responses to freezing of three slug species common in Scandinavia (Arion ater, Arion rufus and Arion lusitanicus) are reported. Autumn collected slugs were cold acclimated in the laboratory and subjected to freezing conditions simulating likely winter temperatures in their habitat. Slugs spontaneously froze at about -4 °C when cooled under dry conditions, but freezing of body fluids was readily induced at -1 °C when in contact with external ice crystals. All three species survived freezing for 2 days at -1 °C, and some A. rufus and A. lusitanicus also survived freezing at -2 °C. (1)H NMR spectroscopy revealed that freezing of body fluids resulted in accumulation of lactate, succinate and glucose. Accumulation of lactate and succinate indicates that ATP production occurred via fermentative pathways, which is likely a result of oxygen depletion in frozen tissues. Glucose increased from about 6 to 22 μg/mg dry tissue upon freezing in A. rufus, but less so in A. ater and A. lusitanicus. Glucose may thus act as a cryoprotectant in these slugs, although the concentrations are not as high as reported for other freeze tolerant invertebrates. Copyright © 2012 Elsevier Inc. All rights reserved.

To freeze or not to freeze embryos: clarity, confusion and conflict.

PubMed

Goswami, Mohar; Murdoch, Alison P; Haimes, Erica

2015-06-01

Although embryo freezing is a routine clinical practice, there is little contemporary evidence on how couples make the decision to freeze their surplus embryos, or of their perceptions during that time. This article describes a qualitative study of 16 couples who have had in vitro fertilisation (IVF) treatment. The study question was 'What are the personal and social factors that patients consider when deciding whether to freeze embryos?' We show that while the desire for a baby is the dominant drive, couples' views revealed more nuanced and complex considerations in the decision-making process. It was clear that the desire to have a baby influenced couples' decision-making and that they saw freezing as 'part of the process'. However, there were confusions associated with the term 'freezing' related to concerns about the safety of the procedure. Despite being given written information, couples were confused about the practical aspects of embryo freezing, which suggests they were preoccupied with the immediate demands of IVF. Couples expressed ethical conflicts about freezing 'babies'. We hope the findings from this study will inform clinicians and assist them in providing support to couples confronted with this difficult decision-making.

Silicon-based Porous Ceramics via Freeze Casting of Preceramic Polymers

NASA Astrophysics Data System (ADS)

Naviroj, Maninpat

Freeze casting is a technique for processing porous materials that has drawn significant attention for its effectiveness in producing a variety of tailorable pore structures for ceramics, metals, and polymers. With freeze casting, pores are generated based on a solidification process where ice crystals act as a sacrificial template which can eventually be sublimated to create pores. While the majority of freeze-casting studies have been performed using conventional ceramic suspensions, this work explores an alternative processing route by freeze casting with preceramic polymer solutions. Significant differences exist between freeze casting of a particulate suspension and a polymeric solution. These changes affect the processing method, solidification behavior, and pore structure, thereby introducing new challenges and possibilities for the freeze-casting technique. The first part of this study explored the processing requirements involved with freeze casting of preceramic polymers, along with methods to control the resulting pore structure. Solvent choice, freezing front velocity, and polymer concentration were used as processing variables to manipulate the pore structures. A total of seven organic solvents were freeze cast with a polymethylsiloxane preceramic polymer to produce ceramics with isotropic, dendritic, prismatic, and lamellar pore morphologies. Changes in freezing front velocity and polymer concentration were shown to influence pore size, shape, and connectivity. Differences between suspension- and solution-based samples freeze cast under equivalent conditions were also investigated. Certain solidification microstructures were strongly affected by the presence of suspended particles, creating differences between pore structures generated from the same solvents. Additionally, processing of solution-based samples were found to be the more facile technique. Compressive strength and water permeability of dendritic and lamellar structures were analyzed to determine functional differences between the pore structures. Results show that dendritic structures were up to 30 times stronger, while lamellar structures provided higher permeability constants. A change in freezing front velocity was shown to significantly affect permeability but not compressive strength. Finally, improved pore alignment along the freezing direction was achieved by controlling the nucleation and growth of solvent crystals through the use of a grain-selection template. Dendritic samples freeze cast with a template showed substantial increase in pore alignment, as determined by image analysis and permeability tests, with the permeability constant increasing by up to 6-fold when compared to a control sample.

Modification of physical properties of freeze-dried rice

NASA Technical Reports Server (NTRS)

Huber, C. S.

1971-01-01

Freeze cycling process consists of alternately freezing and thawing precooked rice for two cycles, rice is then frozen and freeze-dehydrated in vacuum sufficient to remove water from rice by sublimitation. Process modifies rice grain structure and porosity, enabling complete rehydration in one minute in hot water.

9 CFR 590.534 - Freezing facilities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Freezing facilities. 590.534 Section 590.534 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE EGG..., and Facility Requirements § 590.534 Freezing facilities. (a) Freezing rooms, either on or off the...