Removal of sodium lauryl sulphate by coagulation/flocculation with Moringa oleifera seed extract.

PubMed

Beltrán-Heredia, J; Sánchez-Martín, J

2009-05-30

Among other natural flocculant/coagulant agents, Moringa oleifera seed extract ability to remove an anionic surfactant has been evaluated and it has been found to be very interesting. Sodium lauryl sulphate was removed from aqueous solutions up to 80% through coagulation/flocculation process. pH and temperature were found to be not very important factors in removal efficiency. Freundlich (F), Frumkin-Fowler-Guggenheim (FFG) and Gu-Zhu (GZ) models were used to adjust experimental data in a solid-liquid adsorption hypothesis. Last one resulted to be the most accurate one. Several data fit parameters were determined, as Freundlich order, which was found to be 1.66, Flory-Huggins interaction parameter from FFG model, which was found to be 4.87; and limiting Moringa surfactant adsorption capacity from GZ model, which was found to be 2.13 x 10(-3)mol/g.

Thermodynamic and kinetic studies on CO2 capture with Poly[VBTMA][Arg

NASA Astrophysics Data System (ADS)

Raja Shahrom, Maisara Shahrom; Wilfred, Cecilia Devi; Chong, Fai Kait

2018-05-01

This paper discusses the technologies for capturing CO2 from the natural gas using poly[VBTMA][Arg], a type of poly(ionic liquids) with an amino acid as the anion. The results revealed that the CO2 uptake increased from 3.23 mmol/g to 7.91 mmol/g at 1-10 bar, 298 K due to both chemical absorption and physical adsorption increments. Four adsorption isotherm models were applied to study the interaction between adsorbate and adsorbent to study the physical adsorption i.e. Freundlich, Langmuir, Dubinin Raduschkevich and Temkin isotherms at 298 K, 313 K and 333 K. Promising results were obtained that suggested the Freundlich model and the pseudo-first order model are well fitted with the kinetic data at 298 K with a 0.9943 R2 value. This study has provided empirical evidence to the current body of knowledge pertaining to CO2 capture technologies.

Comparison of adsorption equilibrium models for the study of CL-, NO3- and SO4(2-) removal from aqueous solutions by an anion exchange resin.

PubMed

Dron, Julien; Dodi, Alain

2011-06-15

The removal of chloride, nitrate and sulfate ions from aqueous solutions by a macroporous resin is studied through the ion exchange systems OH(-)/Cl(-), OH(-)/NO(3)(-), OH(-)/SO(4)(2-), and HCO(3)(-)/Cl(-), Cl(-)/NO(3)(-), Cl(-)/SO(4)(2-). They are investigated by means of Langmuir, Freundlich, Dubinin-Radushkevitch (D-R) and Dubinin-Astakhov (D-A) single-component adsorption isotherms. The sorption parameters and the fitting of the models are determined by nonlinear regression and discussed. The Langmuir model provides a fair estimation of the sorption capacity whatever the system under study, on the contrary to Freundlich and D-R models. The adsorption energies deduced from Dubinin and Langmuir isotherms are in good agreement, and the surface parameter of the D-A isotherm appears consistent. All models agree on the order of affinity OH(-)

Application of AMDS mortar as a treatment agent for arsenic in subsurface environment

NASA Astrophysics Data System (ADS)

Choi, J.; Lee, H.; Choi, U. K.; Yang, I. J.

2014-12-01

Among the treatment technologies available for As in soil and groundwater, adsorption or precipitation using acid mine drainage (AMD) sludge has become a promised technique because of high efficiency, inexpensiveness and simple to handling. The adsorbents were prepared by addition of Cement, Joomoonjin sand, fly ash, and Ca(OH)2 to air dry AMD sludge. In this work, the adsorption of As (III) and As (V) on AMDS mortar has been studied as a function of kinetic, pH, and initial arsenic concentration. Results of batch study showed that 75-90% of both As (III) and As (V) were removed at pH 7. Arsenic adsorption capacities were the highest at neutral pH condition and the adsorption equilibrium time reached in 7 days using AMDS mortar. Additionally, the adsorption kinetic process is expressed well by pseudo-second-order model. The adsorption capacities of AMDS mortar for As(III) and As(V) were found 19.04 and 30.75 mg g-1, respectively. The results of As (III) adsorption isotherms were fitted well to the Freundlich model. Moreover, As (V) adsorption isotherms were fitted well to the Langmuir model rather than Freundlich model. Based on experimental results in this study, we could conclude that AMDS mortar can be effectively used for arsenic removal agent from subsurface environment.

Adsorption-desorption behavior of atrazine on agricultural soils in China.

PubMed

Yue, Lin; Ge, ChengJun; Feng, Dan; Yu, Huamei; Deng, Hui; Fu, Bomin

2017-07-01

Adsorption and desorption are important processes that affect atrazine transport, transformation, and bioavailability in soils. In this study, the adsorption-desorption characteristics of atrazine in three soils (laterite, paddy soil and alluvial soil) were evaluated using the batch equilibrium method. The results showed that the kinetics of atrazine in soils was completed in two steps: a "fast" adsorption and a "slow" adsorption and could be well described by pseudo-second-order model. In addition, the adsorption equilibrium isotherms were nonlinear and were well fitted by Freundlich and Langmuir models. It was found that the adsorption data on laterite, and paddy soil were better fitted by the Freundlich model; as for alluvial soil, the Langmuir model described it better. The maximum atrazine sorption capacities ranked as follows: paddy soil>alluvial soil>laterite. Results of thermodynamic calculations indicated that atrazine adsorption on three tested soils was spontaneous and endothermic. The desorption data showed that negative hysteresis occurred. Furthermore, lower solution pH value was conducive to the adsorption of atrazine in soils. The atrazine adsorption in these three tested soils was controlled by physical adsorption, including partition and surface adsorption. At lower equilibrium concentration, the atrazine adsorption process in soils was dominated by surface adsorption; while with the increase of equilibrium concentration, partition was predominant. Copyright © 2016. Published by Elsevier B.V.

Adsorption properties of kaolinite-based nanocomposites for Fe and Mn pollutants from aqueous solutions and raw ground water: kinetics and equilibrium studies.

PubMed

Shaban, Mohamed; Hassouna, Mohamed E M; Nasief, Fadya M; AbuKhadra, Mostafa R

2017-10-01

Raw kaolinite was used in the synthesis of metakaolinite/carbon nanotubes (K/CNTs) and kaolinite/starch (K/starch) nanocomposites. Raw kaolinite and the synthetic composites were characterized using XRD, SEM, and TEM techniques. The synthetic composites were used as adsorbents for Fe and Mn ions from aqueous solutions and natural underground water. The adsorption by the both composites is highly pH dependent and achieves high efficiency within the neutral pH range. The experimental adsorption data for the uptake of Fe and Mn ions by K/CNTs were found to be well represented by the pseudo-second-order kinetic model rather than the intra-particle diffusion model or Elovich model. For the adsorption using K/starch, the uptake results of Fe ions was well fitted by the second-order model, whereas the uptake of Mn ions fitted well to the Elovich model rather than pseudo-second-order and intra-particle diffusion models The equilibrium studies revealed the excellent fitting of the removal of Fe and Mn ions by K/CNTs and Fe using K/starch with the Langmuir isotherm model rather than with Freundlich and Temkin models. But the adsorption of Mn ions by K/starch is well fitted with Freundlich rather than Temkin and Langmuir isotherm models. The thermodynamic studies reflected the endothermic nature and the exothermic nature for the adsorption by K/CNTs and K/starch nanocomposites, respectively. Natural ground water contaminated by 0.4 mg/L Fe and 0.5 mg/L Mn was treated at the optimum conditions of pH 6 and 120 min contact time. Under these conditions, 92.5 and 72.5% Fe removal efficiencies were achieved using 20 mg of K/CNTs and K/starch nanocomposites, respectively. Also, K/CNTs nanocomposite shows higher efficiency in the removal of Mn ions as compared to K/starch nanocomposite.

Isolation and identification of Trichoderma harzianum from groundwater: An effective biosorbent for defluoridation of groundwater.

PubMed

Koshle, Shalini; Mahesh, S; Swamy, S Nanjunda

2016-01-01

The ability of non-viable form of Trichoderma harzianum, isolated from fluoride rich groundwater, was investigated as biosorbent for defluoridation of groundwater. Biosorption experiments were carried out at laboratory scale for removal of fluoride from groundwater. Significant effect of operational parameters on fluoride biosorption using Trichoderma harzianum as biosorbent was evaluated by varying operational parameters such as: initial fluoride concentration (2-8 mgl(-1)), biosorbent dose (0.4-1.6g/100ml), groundwater pH (6-10), temperature (30-50 degrees C) and biosorption time (30-120 min). The fluoride adsorption isotherms were modeled by Langmuir and Freundlich isotherms. Our result showed that fluoride biosorption, significantly increased with increase in groundwater pH, biosorbent dose, temperature and biosorption time, whereas increase in initial fluoride concentration reduced fluoride removal. The fluoride biosorption was rapid and maximum fluoride uptake was attained with 1.6g 100ml(-1) biosorbent within 60 min. Optimal pH 10 and temperature 50 degrees C gave maximum defluoridation efficiency. Freundlich isotherm fits well for defluoridation of groundwater using Trichoderma harzianum as biosorbent which indicated that biosorbent surface sites were heterogeneous in nature and fitted into heterogeneous site binding model.

Sorption of diclofenac and naproxen onto MWCNT in model wastewater treated by H2O2 and/or UV.

PubMed

Czech, Bożena; Oleszczuk, Patryk

2016-04-01

The application of oxidation processes such as UV and/or H2O2 will change the physicochemical properties of carbon nanotubes (CNT). It may affect the sorption affinity of CNT to different contaminants and then affect their fate in the environment. In the present study the adsorption of two very common used pharmaceuticals (diclofenac and naproxen) onto CNT treated by UV, H2O2 or UV/H2O2 was investigated. Four different adsorption models (Freundlich, Langmuir, Temkin, Dubinin-Radushkevich) were tested. The best fitting of experimental data was observed for Freundlich or Langmuir model. The significant relationships between Q calculated from Langmuir model with O% and dispersity were observed. Kinetics of diclofenac and naproxen followed mainly pseudo-second order indicating for chemisorption limiting step of adsorption. The data showed that the mechanism of sorption was physical or chemical depending on the type of CNT modification. Copyright © 2015 Elsevier Ltd. All rights reserved.

Dimethyl diallyl ammonium chloride and diallylamin Co-polymer modified bio-film derived from palm dates for the adsorption of dyes.

PubMed

Jabli, Mahjoub; Saleh, Tawfik A; Sebeia, Nouha; Tka, Najeh; Khiari, Ramzi

2017-10-31

For the first time, co-polymer of dimethyl diallyl ammonium chloride and diallylamin (PDDACD) was used to modify the films derived from the waste of palm date fruits, which were then investigated by the purification of colored aqueous solutions. The physico-chemical characteristics were identified using data color, FT-IR spectroscopy, and SEM features. The modified films were evaluated as adsorbents of Methylene Blue (MB), Direct Yellow 50 (DY50), Reactive Blue 198 (RB198) and Naphtol Blue Black (NBB). High retention capacities were achieved in the following order: The equilibrium da DY50 (14 mg g -1 ) < RB198 (16 mg g -1 ) < NBB (63.9 mg g -1 ) < MB (150 mg g -1 ). The kinetic modeling of the data revealed that the adsorption data follows the pseudo second order model. It was fitted to the Langmuir, Freundlich, Temkin, and Dubinin-Redushkevich equations, and the data best fit the Freundlich model indicating that the adsorption might occur in the heterogeneous adsorption sites. These results reveal that PDDACD modified films are valuable materials for the treatment of industrial wastewater. Moreover, the as-prepared adsorbent is economically viable and easily controllable for pollutant adsorption.

Pecan nutshell as biosorbent to remove Cu(II), Mn(II) and Pb(II) from aqueous solutions.

PubMed

Vaghetti, Julio C P; Lima, Eder C; Royer, Betina; da Cunha, Bruna M; Cardoso, Natali F; Brasil, Jorge L; Dias, Silvio L P

2009-02-15

In the present study we reported for the first time the feasibility of pecan nutshell (PNS, Carya illinoensis) as an alternative biosorbent to remove Cu(II), Mn(II) and Pb(II) metallic ions from aqueous solutions. The ability of PNS to remove the metallic ions was investigated by using batch biosorption procedure. The effects such as, pH, biosorbent dosage on the adsorption capacities of PNS were studied. Four kinetic models were tested, being the adsorption kinetics better fitted to fractionary-order kinetic model. Besides that, the kinetic data were also fitted to intra-particle diffusion model, presenting three linear regions, indicating that the kinetics of adsorption should follow multiple sorption rates. The equilibrium data were fitted to Langmuir, Freundlich, Sips and Redlich-Peterson isotherm models. Taking into account a statistical error function, the data were best fitted to Sips isotherm model. The maximum biosorption capacities of PNS were 1.35, 1.78 and 0.946mmolg(-1) for Cu(II), Mn(II) and Pb(II), respectively.

Rates and equilibria of perfluorooctanoate (PFOA) sorption on soils from different regions of China.

PubMed

Miao, Yu; Guo, Xuetao; Dan Peng; Fan, Tingyu; Yang, Chen

2017-05-01

Understanding sorption of PFOA on soil particles is crucial to evaluate its environmental risk. Here, sorption of PFOA onto ten agricultural soils was examined. The influence of soil physico-chemical properties on PFOA sorption was investigated. The sorption rate of PFOA followed a pseudo-second-order kinetics. Isotherm data of PFOA sorption was fitted with both Freundlich and linear models and the latter fitted better. The sorption-desorption of PFOA onto ten soil samples depended on soil organic carbon content and composition of soil minerals. The sorption and desorption isotherms of PFOA on ten soils were linear, except for the sorption of PFOA onto a few soils, which was described by the Freundlich equation with the parameter N >1. The main sorption mechanism of PFOA was hydrophobic interaction between the perfluorinated carbon chain and the organic matter of soil, as evidenced by the correlation between the solid-liquid distribution coefficient and the fraction of soil organic carbon. The sorption of PFOA in soils was highly irreversible. Copyright © 2017 Elsevier Inc. All rights reserved.

Pyrethroid sorption to Sacramento River suspended solids and bed sediments

PubMed Central

Fojut, Tessa L.; Young, Thomas M.

2011-01-01

Sorption of pyrethroid insecticides to solid materials will typically dominate the fate and transport of these hydrophobic compounds in aquatic environments. Batch reactor isotherm experiments were performed with bifenthrin and λ-cyhalothrin with suspended material and bed sediment collected from the Sacramento River, CA. These batch reactor experiments were performed with low spiking concentrations and a long equilibration time (28 d) to be more relevant to environmental conditions. Sorption to suspended material and bed sediment was compared to examine the role of differential sorption between these phases in the environmental transport of pyrethroids. The equilibrium sorption data were fit to the Freundlich isotherm model and fit with r2 > 0.87 for all experiments. Freundlich exponents ranged from 0.72 ± 0.19 to 1.07 ± 0.050, indicating sorption nonlinearity for some of the experimental conditions and linearity for others over the concentration range tested. The Freundlich capacity factors were larger for the suspended solids than for the bed sediments and the suspended material had a higher specific surface area and higher organic carbon content compared to the bed sediment. Calculated organic carbon-normalized distribution coefficients were larger than those previously reported in the literature by approximately an order of magnitude and ranged from 106.16 to 106.68 at an equilibrium aqueous concentration of 0.1 µg/L. Higher than expected sorption of pyrethroids to the tested materials may be explained by sorption to black carbon and/or mineral surfaces. PMID:21191877

Effects and mechanistic aspects of absorbing organic compounds by coking coal.

PubMed

Ning, Kejia; Wang, Junfeng; Xu, Hongxiang; Sun, Xianfeng; Huang, Gen; Liu, Guowei; Zhou, Lingmei

2017-11-01

Coal is a porous medium and natural absorbent. It can be used for its original purpose after adsorbing organic compounds, its value does not reduce and the pollutants are recycled, and then through systemic circulation of coking wastewater zero emissions can be achieved. Thus, a novel method of industrial organic wastewater treatment using adsorption on coal is introduced. Coking coal was used as an adsorbent in batch adsorption experiments. The quinoline, indole, pyridine and phenol removal efficiencies of coal adsorption were investigated. In addition, several operating parameters which impact removal efficiency such as coking coal consumption, oscillation contact time, initial concentration and pH value were also investigated. The coking coal exhibited properties well-suited for organics' adsorption. The experimental data were fitted to Langmuir and Freundlich isotherms as well as Temkin and Redlich-Peterson (R-P) models. The Freundlich isotherm model provided reasonable models of the adsorption process. Furthermore, the purification mechanism of organic compounds' adsorption on coking coal was analysed.

Synthesis of humidity sensitive zinc stannate nanomaterials and modelling of Freundlich adsorption isotherm model

NASA Astrophysics Data System (ADS)

Sharma, Alfa; Kumar, Yogendra; Shirage, Parasharam M.

2018-04-01

The chemi-resistive humidity sensing behaviour of as prepared and annealed ZnSnO3 nanoparticles synthesized using a wet chemical synthesis method was investigated. The effect of stirring temperature over the evolution of varied nanomorphology of zinc stannate is in accordance to Ostwald's ripening law. At room temperature, an excellent humidity sensitivity of ˜800% and response/recovery time of 70s./102s. is observed for ZnSnO3 sample within 08-97% relative humidity range. The experimental data observed over the entire range of RH values well fitted with the Freundlich adsorption isotherm model, and revealing two distinct water adsorption regimes. The excellent humidity sensitivity observed in the nanostructures is attributed to Grotthuss mechanism considering the availability and distribution of available adsorption sites. This present result proposes utilization of low cost synthesis technique of ZnSnO3 holds the promising capabilities as potential candidate for the fabrication of next generation humidity sensors.

Decolorisation of Basic Textile Dye from Aqueous Solutions using a Biosorbent derived from Thespesia populnea used Biomass

NASA Astrophysics Data System (ADS)

Gunturu, Bhargavi; Rao Palukuri, Nageswara; Sahadevan, Renganathan

2018-03-01

In the present study, the efficiency of a biosorbent derived from seeds of Thespesia populnea was investigated towards the removal of basic textile dye Methylene Blue from an aqueous solution. Adsorption studies were carried out in batch system. Influence of experimental parameters such as adsorbent dosage (0.1g/L-0.3g/L), PH (2-10) and initial dye concentration (50-130mg/L) on adsorption of dye onto biosorbent was investigated. Maximum uptake of dye was observed with 0.1g/L adsorbent dosage at PH 8.0. Equilibrium uptake of methylene blue dye by the adsorbent was analyzed by Langmuir and Freundlich isotherm models. The data fitted best with Freundlich model, suggesting that adsorption of the dye was by multilayer model on the surface of the adsorbent. Experimental results obtained support that the biosorbent used in the present study can be a suitable low cost alternate for the removal of basic textile dyes.

Cadmium mobility in sediments and soils from a coal mining area on Tibagi River watershed: environmental risk assessment.

PubMed

Galunin, Evgeny; Ferreti, Jeferson; Zapelini, Iago; Vieira, Isadora; Ricardo Teixeira Tarley, César; Abrão, Taufik; Santos, Maria Josefa

2014-01-30

The risk of cadmium contamination in the Tibagi River watershed (Parana State, Brazil) affected by past coal mining activities was assessed through sorption-desorption modeling for sediment and soil samples. The acidic character of the samples resulted in more competition between the cadmium ions and protons, thereby influencing the cadmium sorption-desorption. The sorption isotherms were fitted to the Langmuir and Freundlich single models and to the dual-site Langmuir-Freundlich (or Sips) model. The single-site models indicated a low-energy character of sorption sites on the sample sorption sites, whereas the dual-site model explained the availability of higher-affinity and lower-affinity non-specific sites. The correlation of the sorption and desorption constants with the physicochemical and mineralogical characteristics of the samples showed that the cadmium sorption behavior was significantly affected by the pH, point of zero charge, and also by the magnesium, aluminum, calcium and manganese amounts. Besides, the desorption rate and hysteresis index suggested a high risk of cadmium mobilization along the Tibagi River basin. Copyright © 2013 Elsevier B.V. All rights reserved.

A Decolorization Technique with Spent “Greek Coffee” Grounds as Zero-Cost Adsorbents for Industrial Textile Wastewaters

PubMed Central

Kyzas, George Z.

2012-01-01

In this study, the decolorization of industrial textile wastewaters was studied in batch mode using spent “Greek coffee” grounds (COF) as low-cost adsorbents. In this attempt, there is a cost-saving potential given that there was no further modification of COF (just washed with distilled water to remove dirt and color, then dried in an oven). Furthermore, tests were realized both in synthetic and real textile wastewaters for comparative reasons. The optimum pH of adsorption was acidic (pH = 2) for synthetic effluents, while experiments in free pH (non-adjusted) were carried out for real effluents. Equilibrium data were fitted to the Langmuir, Freundlich and Langmuir-Freundlich (L-F) models. The calculated maximum adsorption capacities (Qmax) for total dye (reactive) removal at 25 °C was 241 mg/g (pH = 2) and 179 mg/g (pH = 10). Thermodynamic parameters were also calculated (ΔH0, ΔG0, ΔS0). Kinetic data were fitted to the pseudo-first, -second and -third order model. The optimum pH for desorption was determined, in line with desorption and reuse analysis. Experiments dealing the increase of mass of adsorbent showed a strong increase in total dye removal.

Studies on adsorption of phenol from wastewater by agricultural waste.

PubMed

Girish, C R; Ramachandramurty, V

2013-07-01

In this paper, preliminary investigation of various agricultural wastes-Rice mill residue (RM), Wheat mill reside (WM), Dall mill residue (DM) and the Banana peels (BM) was carried out to study their ability to be used as adsorbents for phenol-removal from wastewater. This study reports the feasibility of employing dal mill residue waste (DM) as an adsorbent for removing phenol from wastewater. The performance of DM was compared with the commercially available activated carbon (CAC). Batch mode experiments were conducted with activated DM to study the effects of initial concentration of phenol, pH and the temperature of aqueous solution on adsorption. Equilibrium adsorption isotherms and kinetics were investigated. The experimental data were analyzed by the Langmuir, Freundlich and Temkin models and the isotherm data fitted well to the Freundlich isotherm with monolayer adsorption capacity of 6.189 mg/g. The kinetic data obtained at different concentrations were analyzed using a pseudo-first order and pseudo-second- order equation. The experimental data fitted very well with the pseudo-first-order kinetic model. The FTIR analysis revealed that carboxyl and hydroxyl functional groups were mainly responsible for the sorption of phenol. Finally, the DM was found to be a promising adsorbent for phenol adsorption as compared to activated carbon.

Adsorption equilibrium and dynamics of toluene vapors onto three kinds of silica gels

NASA Astrophysics Data System (ADS)

Yan, K. L.; Wang, Q.

2018-01-01

The benzene is the representative of VOCs and widely exists in the industrial waste gas. In this study, adsorption equilibrium and dynamics of toluene vapors at five initial concentrations (1.39 g·m-3, 5.12 g·m-3, 8.38 g·m-3, 15.6 g·m-3, 21.3 g·m-3) onto three kinds of silica gels (GA, GB and GC) were investigated and compared. The experimental results showed that GA has the rich microporous and mesoporous distributions, and the larger surface area and microporous volume than GB and GC. It can be clearly seen that the order of the adsorption rate of adsorbents on the silica gels samples is GA, GB and GC. Due to the suitable pore distribution in the region of micropore and mesopore (1-4 nm), GA exhibits the comparable breakthrough adsorption capacities with GB and GC for a given initial concentration. Moreover, the experimental data were fitted to the Langmuir and Freundlich models, respectively. The Freundlich isotherms correlated with the experimental data presented a better fitting than Langmuir model. Taken together, it is expected that GA silica gel would be a promising adsorbent for the removal of toluene vapors from gas streams.

Liquid-phase separation of reactive dye by wood-rotting fungus: a biotechnological approach.

PubMed

Binupriya, Arthur R; Sathishkumar, Muthuswamy; Dhamodaran, Kavitha; Jayabalan, Rasu; Swaminathan, Krishnaswamy; Yun, Sei Eok

2007-08-01

The live and pretreated mycelial pellets/biomass of Trametes versicolor was used for the biosorption of a textile dye, reactive blue MR (RBMR) from aqueous solution. The parameters that affect the biosorption of RBMR, such as contact time, concentration of dye and pH, on the extent of RBMR adsorption were investigated. To develop an effective and accurate design model for removal of dye, adsorption kinetics and equilibrium data are essential basic requirements. Lagergren first-order, second-order and Bangham's model were used to fit the experimental data. Results of the kinetic studies showed that the second order kinetic model fitted well for the present experimental data. The Langmuir, Freundlich and Temkin adsorption models were used for the mathematical description of the biosorption equilibrium. The biosorption equilibrium data obeyed well for Langmuir isotherm and the maximum adsorption capacities were found to be 49.8, 51.6, 47.4 and 46.7 mg/g for live, autoclaved, acid- and alkali-pretreated biomass. The dye uptake capacity order of the fungal biomass was found as autoclaved > live > acid-treated > alkali-pretreated. The Freundlich and Temkin models were also able to describe the biosorption equilibrium on RBMR on live and pretreated fungal biomass. Acidic pH was favorable for the adsorption of dye. Studies on pH effect and desorption show that chemisorption seems to play a major role in the adsorption process. On comparison with fixed bed adsorption, batch mode adsorption was more efficient in adsorption of RBMR.

Sorption of metolachlor and atrazine in fly ash amended soils: comparison of optimized isotherm models.

PubMed

Ghosh, Rakesh K; Singh, Neera

2012-01-01

Adsorption of metolachlor and atrazine was studied in the fly ash (Inderprastha and Badarpur)- amended Inceptisol and Alfisol soils using batch method. Results indicated that sorption of both the herbicides in soil+fly ash mixtures was highly nonlinear and sorption decreased with a higher herbicide concentration in the solution. Also, nonlinearity increased with an increase in the level of fly ash amendment from 0-5%. Three two-parameter monolayer isotherms viz. Langmuir, Temkin, Jovanovic and one imperical Freundlich models were used to fit the experimental data. Data analysis and comparison revealed that the Temkin and the Freundlich isotherms were best-suited to explain the sorption results and the observed and the calculated adsorption coefficient values showed less variability. The study suggested that sorption mechanism of metolachlor and atrazine involved the physical association at the sorbate surface and the nonlinearity in the sorption at higher pesticide or fly ash concentration was due to a decrease in the heat of adsorption and higher binding energy.

Pyrethroid sorption to Sacramento River suspended solids and bed sediments.

PubMed

Fojut, Tessa L; Young, Thomas M

2011-04-01

Sorption of pyrethroid insecticides to solid materials will typically dominate the fate and transport of these hydrophobic compounds in aquatic environments. Batch reactor isotherm experiments were performed with bifenthrin and λ-cyhalothrin with suspended material and bed sediment collected from the Sacramento River, California, USA. These batch reactor experiments were performed with low spiking concentrations and a long equilibration time (28 d) to be more relevant to environmental conditions. Sorption to suspended material and bed sediment was compared to examine the role of differential sorption between these phases in the environmental transport of pyrethroids. The equilibrium sorption data were fit to the Freundlich isotherm model and fit with r(2)  > 0.87 for all experiments. Freundlich exponents ranged from 0.72 ± 0.19 to 1.07 ± 0.050, indicating sorption nonlinearity for some of the experimental conditions and linearity for others over the concentration range tested. The Freundlich capacity factors were larger for the suspended solids than for the bed sediments, and the suspended material had a higher specific surface area and higher organic carbon content compared to the bed sediment. Calculated organic carbon-normalized distribution coefficients were larger than those previously reported in the literature, by approximately an order of magnitude, and ranged from 10(6.16) to 10(6.68) at an equilibrium aqueous concentration of 0.1 µg/L. Higher than expected sorption of pyrethroids to the tested materials may be explained by sorption to black carbon and/or mineral surfaces. Copyright © 2011 SETAC.

The promise of a specially-designed graft copolymer of acrylic acid onto cellulose as selective sorbent for heavy metal ions.

PubMed

Essawy, Hisham A; Mohamed, Magdy F; Ammar, Nabila S; Ibrahim, Hanan S

2017-10-01

A specially-designed graft copolymer of acrylic acid onto in-situ formed cellulose-fulvate hybrid showed privileged tendency for uptake of Pb(II) during competitive removal from a mixture containing Cd(II) and Ni(II) within 5min at pH 5. This novel trend is attributed mainly to the crowded high content of coordinating centers within the designed graft copolymer along with the acquired superabsorbency. This provides an outstanding tool to separate some metal ions selectively from mixtures containing multiple ions on kinetic basis. Thus, the designed graft copolymer structure exhibited superior efficiency that reached ∼95% for sole removal of Pb(II). Kinetic modeling for Pb(II) individual removal showed excellent fitting with a pseudo second-order model. Intraparticle diffusion model on the other hand ensured governance of boundary layer effect over diffusion during the removal process due to the superabsorbency feature of the graft copolymer. The experimental findings were described with models such as Freundlich, Langmuir, and Dubinin-Radushkevich. The Langmuir and Freundlich models showed convenience with the adsorption isotherm of Pb(II) onto the developed graft copolymer. Copyright © 2017 Elsevier B.V. All rights reserved.

Copper ions removal from water using functionalized carbon nanotubes–mullite composite as adsorbent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tofighy, Maryam Ahmadzadeh; Mohammadi, Toraj, E-mail: torajmohammadi@iust.ac.ir

Highlights: • CNTs–mullite composite was prepared via chemical vapor deposition (CVD) method. • The prepared composite was modified with concentrated nitric acid and chitosan. • The modified CNTs–mullite composites were used as novel adsorbents. • Copper ion removal from water by the prepared adsorbents was performed. • Langmuir and Freundlich isotherms and two kinetic models were applied to fit the experimental data. - Abstract: Carbon nanotubes–mullite composite was synthesized by direct growth of carbon nanotubes on mullite particles via chemical vapor deposition method using cyclohexanol and ferrocene as carbon precursor and catalyst, respectively. The carbon nanotubes–mullite composite was oxidized withmore » concentrated nitric acid and functionalized with chitosan and then used as a novel adsorbent for copper ions removal from water. The results demonstrated that modification with concentrated nitric acid and chitosan improves copper ions adsorption capacity of the prepared composite, significantly. Langmuir and Freundlich isotherms and two kinetic models were applied to fit the experimental data. The carbon nanotubes growth on mullite particles to form the carbon nanotubes–mullite composite with further modification is an inherently safe approach for many promising environmental applications to avoid some concerns regarding environment, health and safety. It was found that the modified carbon nanotubes–mullite composite can be considered as an excellent adsorbent for copper ions removal from water.« less

Adsorption and removal of clofibric acid and diclofenac from water with MIEX resin.

PubMed

Lu, Xian; Shao, Yisheng; Gao, Naiyun; Chen, Juxiang; Zhang, Yansen; Wang, Qiongfang; Lu, Yuqi

2016-10-01

This study demonstrates the use of MIEX resin as an efficient adsorbent for the removal of clofibric acid (CA) and diclofenac (DCF). The adsorption performance of CA and DCF are investigated by a batch mode in single-component or bi-component adsorption system. Various factors influencing the adsorption of CA and DCF, including initial concentration, contact time, adsorbent dosage, initial solution pH, agitation speed, natural organic matter and coexistent anions are studied. The Langmuir model can well describe CA adsorption in single-component system, while the Freundlich model gives better fitting in bi-component system. The DCF adsorption can be well fitted by the Freundlich model in both systems. Thermodynamic analyses show that the adsorption of CA and DCF is an endothermic (ΔH(o) > 0), entropy driven (ΔS(o) > 0) process and more randomness exists in the DCF adsorption process. The values of Gibbs free energy (ΔG(o) < 0) indicate the adsorption of DCF is spontaneous but nonspontaneous (ΔG(o) > 0) for CA adsorption. The kinetic data suggest the adsorption of CA and DCF follow the pseudo-first-order model in both systems and the intra-particle is not the unique rate-limiting step. The adsorption process is controlled simultaneously by external mass transfer and surface diffusion according to the surface diffusion modified Biot number (Bis) ranging from 1.06 to 26.15. Moreover, the possible removal mechanism for CA and DCF is respectively proposed based on the ion exchange stoichiometry. Copyright © 2016 Elsevier Ltd. All rights reserved.

Semi-aerobic stabilized landfill leachate treatment by ion exchange resin: isotherm and kinetic study

NASA Astrophysics Data System (ADS)

Zamri, Mohd Faiz Muaz Ahmad; Kamaruddin, Mohamad Anuar; Yusoff, Mohd Suffian; Aziz, Hamidi Abdul; Foo, Keng Yuen

2017-05-01

This study was carried out to investigate the treatability of ion exchange resin (Indion MB 6 SR) for the removal of chromium (VI), aluminium (III), zinc (II), copper (II), iron (II), and phosphate (PO4)3-, chemical oxygen demand (COD), ammonia nitrogen (NH3-N) and colour from semi-aerobic stabilized leachate by batch test. A range of ion exchange resin dosage was tested towards the removal efficiency of leachate parameters. It was observed that equilibrium data were best represented by the Langmuir model for metal ions and Freundlich was ideally fit for COD, NH3-N and colour. Intra particle diffusion model, pseudo first-order and pseudo second-order isotherm models were found ideally fit with correlation of the experimental data. The findings revealed that the models could describe the ion exchange kinetic behaviour efficiently, which further suggests comprehensive outlook for the future research in this field.

Investigation of sorption/desorption equilibria of heavy metal ions on/from quartz using rhamnolipid biosurfactant.

PubMed

Aşçi, Yeliz; Nurbaş, Macid; Sağ Açikel, Yeşim

2010-01-01

In the present study, the sorption characteristics of Cd(II) and Zn(II) ions on quartz, a representative soil-component, and the desorption of these metal ions from quartz using rhamnolipid biosurfactant were investigated. In the first part of the studies, the effects of initial metal ion concentration and pH on sorption of Cd(II) and Zn(II) ions by a fixed amount of quartz (1.5g) were studied in laboratory batch mode. The equilibrium sorption capacity for Cd(II) and Zn(II) ions was measured and the best correlation between experimental and model predicted equilibrium uptake was obtained using the Freundlich model. Although investigations on the desorption of heavy metal ions from the main soil-components are crucial to better understand the mobility and bioavailability of metals in the environment, studies on the description of desorption equilibrium were performed rarely. In the second part, the desorption of Cd(II) and Zn(II) from quartz using rhamnolipid biosurfactant was investigated as a function of pH, rhamnolipid concentration, and the amounts of sorbed Cd(II) and Zn(II) ions by quartz. The Freundlich model was also well fitted to the obtained desorption isotherms. Several indexes were calculated based on the differences of the quantity of Cd-Zn sorbed and desorbed. A desorption hysteresis (irreversibility) index based on the Freundlich exponent, concentration-dependent metal distribution coefficients, and the irreversibility index based on the metal distribution coefficient were used to quantify hysteretic behavior observed in the systems. 2009 Elsevier Ltd. All rights reserved.

Sorption of lead from aqueous solution by chemically modified carbon adsorbents.

PubMed

Nadeem, Muhammad; Mahmood, A; Shahid, S A; Shah, S S; Khalid, A M; McKay, G

2006-12-01

An indigenously prepared, steam activated and chemically modified carbon from husk and pods of Moringa oleifera (M. oleifera), an agricultural waste, was comparatively examined as an adsorbent for the removal of lead from aqueous solutions. Studies were conducted as a function of contact time, initial metal concentration, dose of adsorbent, agitation speed, particle size and pH. Maximum uptake capacities were found to be, 98.89, 96.58, 91.8, 88.63, 79.43% for cetyltrimethyl ammonium bromide (CTAB), phosphoric, sulfuric, hydrochloric acid treated and untreated carbon adsorbents, respectively. Bangham, pseudo-first- and second-order, intra-particle diffusion equations were implemented to express the sorption mechanism by utilized adsorbents. Adsorption rate of lead ions was found to be considerably faster for chemically modified adsorbents than unmodified. The results of adsorption were fitted to both the Langmuir and Freundlich models. Satisfactory agreement between the metal uptake capacities by the adsorbents at different time intervals was expressed by the correlation coefficient (R(2)). The Langmuir model represented the sorption process better than the Freundlich one, with R(2) values ranging from 0.994 to 0.998.

Removal of Pb (II) ions from aqueous solutions by Cladophora rivularis (Linnaeus) Hoek.

PubMed

Jafari, Naser; Senobari, Zoreh

2012-01-01

Biosorption of Pb(II) using Cladophora rivularis was examined as a function of initial pH heavy metal concentration and temperature. The optimum pH value for the biosorption of lead was 4.0. The adsorption equilibriums were well described by Langmuir and Freundlich isotherm models and it was implied by the results that the C. rivularis biomass is suitable for the development of efficient biosorbent in order to remove Pb(II) from wastewater and to recover it. The high values of correlation coefficient (R(2) = 0.984) demonstrate equilibrium data concerning algal biomass, which is well fitted in Freundlich isotherms model equations. The dimensionless parameter R(L) is found in the range of 0.0639 to 0.1925 (0 < R(L) < 1), which confirms the favorable biosorption process. Fourier transform infra-red (FTIR) spectroscopy of C. rivularis was used to reveal the main function groups of biosorption, which were hydroxyl, amine groups, C-H stretching vibrations of -CH3 and -CH2, and complexation with functional groups. All these results suggest that C. rivularis can be used effectively for removal of Pb(II).

Influence of competing inorganic cations on the ion exchange equilibrium of the monovalent organic cation metoprolol on natural sediment.

PubMed

Niedbala, Anne; Schaffer, Mario; Licha, Tobias; Nödler, Karsten; Börnick, Hilmar; Ruppert, Hans; Worch, Eckhard

2013-02-01

The aim of this study was to systematically investigate the influence of the mono- and divalent inorganic ions Na(+) and Ca(2+) on the sorption behavior of the monovalent organic cation metoprolol on a natural sandy sediment at pH=7. Isotherms for the beta-blocker metoprolol were obtained by sediment-water batch tests over a wide concentration range (1-100000 μg L(-1)). Concentrations of the competing inorganic ions were varied within freshwater relevant ranges. Data fitted well with the Freundlich sorption model and resulted in very similar Freundlich exponents (n=0.9), indicating slightly non-linear behavior. Results show that the influence of Ca(2+) compared to Na(+) is more pronounced. A logarithmic correlation between the Freundlich coefficient K(Fr) and the concentration or activity of the competing inorganic ions was found allowing the prediction of metoprolol sorption on the investigated sediment at different electrolyte concentrations. Additionally, the organic carbon of the sediment was completely removed for investigating the influence of organic matter on the sorption of metoprolol. The comparison between the experiments with and without organic carbon removal revealed no significant contribution of the organic carbon fraction (0.1%) to the sorption of metoprolol on the in this study investigated sediment. Results of this study will contribute to the development of predictive models for the transport of organic cations in the subsurface. Copyright © 2012 Elsevier Ltd. All rights reserved.

Modeling Np and Pu transport with a surface complexation model and spatially variant sorption capacities: Implications for reactive transport modeling and performance assessments of nuclear waste disposal sites

USGS Publications Warehouse

Glynn, P.D.

2003-01-01

One-dimensional (1D) geochemical transport modeling is used to demonstrate the effects of speciation and sorption reactions on the ground-water transport of Np and Pu, two redox-sensitive elements. Earlier 1D simulations (Reardon, 1981) considered the kinetically limited dissolution of calcite and its effect on ion-exchange reactions (involving 90Sr, Ca, Na, Mg and K), and documented the spatial variation of a 90Sr partition coefficient under both transient and steady-state chemical conditions. In contrast, the simulations presented here assume local equilibrium for all reactions, and consider sorption on constant potential, rather than constant charge, surfaces. Reardon's (1981) seminal findings on the spatial and temporal variability of partitioning (of 90Sr) are reexamined and found partially caused by his assumption of a kinetically limited reaction. In the present work, sorption is assumed the predominant retardation process controlling Pu and Np transport, and is simulated using a diffuse-double-layer-surface-complexation (DDLSC) model. Transport simulations consider the infiltration of Np- and Pu-contaminated waters into an initially uncontaminated environment, followed by the cleanup of the resultant contamination with uncontaminated water. Simulations are conducted using different spatial distributions of sorption capacities (with the same total potential sorption capacity, but with different variances and spatial correlation structures). Results obtained differ markedly from those that would be obtained in transport simulations using constant Kd, Langmuir or Freundlich sorption models. When possible, simulation results (breakthrough curves) are fitted to a constant K d advection-dispersion transport model and compared. Functional differences often are great enough that they prevent a meaningful fit of the simulation results with a constant K d (or even a Langmuir or Freundlich) model, even in the case of Np, a weakly sorbed radionuclide under the simulation conditions. Functional behaviors that cannot be fit include concentration trend reversals and radionuclide desorption spikes. Other simulation results are fit successfully but the fitted parameters (Kd and dispersivity) vary significantly depending on simulation conditions (e.g. "infiltration" vs. "cleanup" conditions). Notably, an increase in the variance of the specified sorption capacities results in a marked increase in the dispersion of the radionuclides. The results presented have implications for the simulation of radionuclide migration in performance assessments of nuclear waste-disposal sites, for the future monitoring of those sites, and more generally for modeling contaminant transport in ground-water environments. ?? 2003 Published by Elsevier Science Ltd.

Ultrasonically assisted solvothermal synthesis of novel Ni/Al layered double hydroxide for capturing of Cd(II) from contaminated water

NASA Astrophysics Data System (ADS)

Rahmanian, Omid; Maleki, Mohammad Hassan; Dinari, Mohammad

2017-11-01

A novel adsorbent of nickel aluminum layered double hydroxide (Ni/Al-LDH) was prepared through the precipitation of metal nitrates by ultrasonically assisted solvothermal method. The surface morphology, chemical structure and thermal properties of this compound were examined by X-ray diffraction (XRD), Fourier Transform Infrared (FT-IR), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA) techniques. The XRD, TEM and FE-SEM results established that the synthesized LDH have a well-ordered layer structure with good crystalline nature. Then it was applied to remove excessive Cd(II) ions from water and the effects of contact time, pH and adsorbent dose were examined at initial Cd(II) concentration of 10 mg/L. Results show that the time required to reach equilibrium was fast (40 min) and working pH solution was neutral (pH 7). Langmuir and Freundlich model of adsorption isotherms were explored; the results show that the Freundlich model was better fitted than that Langmuir model. This results predicting a multilayer adsorption of Cd(II) on LDH. The equilibrium kinetic adsorption data were fixed to the pseudo-second order kinetic equation.

Removal of barium and strontium from aqueous solution using zeolite 4A.

PubMed

Araissi, Manel; Ayed, Imen; Elaloui, Elimame; Moussaoui, Younes

2016-01-01

The adsorption efficiency of Sr(2+) and Ba(2+) from aqueous solutions by zeolite 4A was investigated. Adsorption studies were carried out both in single and binary component systems. The single ion equilibrium adsorption data were fitted to three isotherm models: Langmuir, Freundlich and Dubinin-Radushkevich. The Langmuir model represents the equilibrium data better than the Freundlich model in the studied initial metal concentration (0.3-25 mmol L(-1)) in both the single and binary component systems. The obtained RL (separation factor or Langmuir parameter) values were in the range of 0-1 indicating that Sr(2+) and Ba(2+) sorption were favorable. The obtained mean free energy value for adsorption of Ba(2+) and Sr(2+) was 8.45 kJ mol(-1) and 9.12 kJ mol(-1), respectively, indicating that both ions were uptaken through an ion exchange process. The maximum adsorption capacities (Qmax) were 2.25 mmol g(-1) and 2.34 mmol g(-1) for Ba(2+) and Sr(2+) ions, respectively. Also, the study of the competitive sorption of ions in the binary system showed that zeolite 4A preferentially adsorbs cations in the following order: Ba(2+) < Sr(2+).

Isotherm, kinetic, and thermodynamic study of ciprofloxacin sorption on sediments.

PubMed

Mutavdžić Pavlović, Dragana; Ćurković, Lidija; Grčić, Ivana; Šimić, Iva; Župan, Josip

2017-04-01

In this study, equilibrium isotherms, kinetics and thermodynamics of ciprofloxacin on seven sediments in a batch sorption process were examined. The effects of contact time, initial ciprofloxacin concentration, temperature and ionic strength on the sorption process were studied. The K d parameter from linear sorption model was determined by linear regression analysis, while the Freundlich and Dubinin-Radushkevich (D-R) sorption models were applied to describe the equilibrium isotherms by linear and nonlinear methods. The estimated K d values varied from 171 to 37,347 mL/g. The obtained values of E (free energy estimated from D-R isotherm model) were between 3.51 and 8.64 kJ/mol, which indicated a physical nature of ciprofloxacin sorption on studied sediments. According to obtained n values as measure of intensity of sorption estimate from Freundlich isotherm model (from 0.69 to 1.442), ciprofloxacin sorption on sediments can be categorized from poor to moderately difficult sorption characteristics. Kinetics data were best fitted by the pseudo-second-order model (R 2  > 0.999). Thermodynamic parameters including the Gibbs free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were calculated to estimate the nature of ciprofloxacin sorption. Results suggested that sorption on sediments was a spontaneous exothermic process.

Relation between some two- and three-parameter isotherm models for the sorption of methylene blue onto lemon peel.

PubMed

Kumar, K Vasanth; Porkodi, K

2006-12-01

Equilibrium uptake of methylne blue onto lemon peel was fitted to the 2 two-parameter isotherm models namely Freundlich and Langmuir and 3 six-parameter isotherm models namely Redlich-Peterson, Toth, Radke-Prausnitz, Fritz-Schluender, Vieth-Sladek and Sips isotherms by non-linear method. A comparison between two-parameter and three-parameter isotherms was reported. The best fitting isotherm was the Sips isotherm followed by Langmuir isotherm and Redlich-Peterson isotherm equation. Redlich-Peterson isotherm is a special case of Langmuir isotherm when the Redlich-Peterson isotherm constant g was unity. Radke-Prausnitz, Toth, Vieth-Sladek isotherm were the same when the Toth isotherm constant, n(T) and the Radke-Prausnitz isotherm, m(RP) are equal to unity and when the Vieth-Sladek isotherm constant, K(VS) equals zero. The sorption capacity of lemon peel for methylene blue uptake was found to be 29 mg/g.

Kinetic and isotherm studies for nickel (II) removal using novel mesoparticle graphene sand composite synthesised from sand and arenga palm sugar

NASA Astrophysics Data System (ADS)

Zularisam, A. W.; Wahida, Norul

2017-07-01

Nickel (II) is one of the most toxic contaminants recognised as a carcinogenic and mutagenic agent which needs complete removal from wastewater before disposal. In the present study, a novel adsorbent called mesoparticle graphene sand composite (MGSCaps) was synthesised from arenga palm sugar and sand by using a green, simple, low cost and efficient methodology. Subsequently, this composite was characterised and identified using field emission scanning electron microscope (FESEM), x-ray diffraction (XRD) and elemental mapping (EM). The adsorption process was investigated and optimised under the experimental parameters such as pH, contact time and bed depth. The results showed that the interaction between nickel (II) and MGSCaps was not ion to ion interaction hence removal of Ni (II) can be applied at any pH. The results were also exhibited the higher contact time and bed depth, the higher removal percentage of nickel (II) occurred. Adsorption kinetic data were modelled using Pseudo-first-order and Pseudo-second-order equation models. The experimental results indicated pseudo-second-order kinetic equation was most suitable to describe the experimental adsorption kinetics data with maximum capacity of 40% nickel (II) removal for the first hour. The equilibrium adsorption data was fitted with Langmuir, and Freundlich isotherms equations. The data suggested that the most fitted equation model is the Freundlich with correlation R2=0.9974. Based on the obtained results, it can be stated that the adsorption method using MGSCaps is an efficient, facile and reliable method for the removal of nickel (II) from waste water.

Adsorption of nicotine from aqueous solution onto hydrophobic zeolite type USY

NASA Astrophysics Data System (ADS)

Lazarevic, Natasa; Adnadjevic, Borivoj; Jovanovic, Jelena

2011-07-01

The isothermal adsorption of nicotine from an aqueous solution onto zeolite type USY was investigated. The adsorption isotherms of nicotine onto the zeolite at different temperatures ranging from 298 to 322 K were determined. It was found that the adsorption isotherms can be described by the model of Freundlich adsorption isotherm. Based on the adsorption isotherms the changes of adsorption heat, free energy and entropy with adsorption degree were determined. The determined decrease of adsorption heat with adsorption degree can be explained by the presence of the adsorption centers of different energy and concentration on interface of zeolite-nicotine solution. It was found that the probability function of density distribution of the heat of adsorption (DDF) has exponential form. It was concluded that the possibility of fitting the adsorption isotherms of nicotine onto the zeolite by Freundlich adsorption isotherm was a direct consequence of that. The determined increase in entropy with the increase in adsorption degree can be explained with the change of phase state of adsorbed nicotine.

Sorption of ochratoxin A from aqueous solutions using β-cyclodextrin-polyurethane polymer.

PubMed

Appell, Michael; Jackson, Michael A

2012-02-01

The ability of a cyclodextrin-polyurethane polymer to remove ochratoxin A from aqueous solutions was examined by batch rebinding assays. The results from the aqueous binding studies were fit to two parameter models to gain insight into the interaction of ochratoxin A with the nanosponge material. The ochratoxin A sorption data fit well to the heterogeneous Freundlich isotherm model. The polymer was less effective at binding ochratoxin A in high pH buffer (9.5) under conditions where ochratoxin A exists predominantly in the dianionic state. Batch rebinding assays in red wine indicate the polymer is able to remove significant levels of ochratoxin A from spiked solutions between 1-10 μg·L(-1). These results suggest cyclodextrin nanosponge materials are suitable to reduce levels of ochratoxin A from spiked aqueous solutions and red wine samples.

Preparation of char from lotus seed biomass and the exploration of its dye removal capacity through batch and column adsorption studies.

PubMed

Nethaji, S; Sivasamy, A; Kumar, R Vimal; Mandal, A B

2013-06-01

Char was obtained from lotus seed biomass by a simple single-step acid treatment process. It was used as an adsorbent for the removal of malachite green dye (MG) from simulated dye bath effluent. The adsorbent was characterized for its surface morphology, surface functionalities, and zero point charge. Batch studies were carried out by varying the parameters such as initial aqueous pH, adsorbent dosage, adsorbent particle size, and initial adsorbate concentration. Langmuir and Freundlich isotherms were used to test the isotherm data and the Freundlich isotherm best fitted the data. Thermodynamic studies were carried out and the thermodynamic parameters such as ∆G, ∆H, and ∆S were evaluated. Adsorption kinetics was carried out and the data were tested with pseudofirst-order model, pseudosecond-order model, and intraparticle diffusion model. Adsorption of MG was not solely by intraparticle diffusion but film diffusion also played a major role. Continuous column experiments were also conducted using microcolumn and the spent adsorbent was regenerated using ethanol and was repeatedly used for three cycles in the column to determine the reusability of the regenerated adsorbent. The column data were modeled with the modeling equations such as Adam-Bohart model, Bed Depth Service Time (BDST) model, and Yoon-Nelson model for all the three cycles.

Adsorption capacity of Curcuma longa for the removal of basic green 1 dye--equilibrium, kinetics and thermodynamic study.

PubMed

Roopavathi, K V; Shanthakumar, S

2016-09-01

In the present study, Curcuma longa (turmeric plant) was used as an adsorbent to remove Basic Green 1 (BG) dye. Batch study was carried out to evaluate the adsorption potential of C. longa and influencing factors such as pH (4-10), adsorbent dose (0.2-5 g l-1), initial dye concentration (50-250 mg l-1) and temperature (30-50°C) on dye removal were analysed. The characterisation of adsorbent was carried out using fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and Brunauer, Emmett and Teller (BET) method. Isotherm models that included Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich, and kinetic models such as pseudo first order, pseudo second-order, Elovich and intraparticle diffusion models were studied. A maximum removal percentage (82.76%) of BG dye from aqueous solution was obtained with optimum conditions of pH 7, 1g l-1 adsorbent dose and 30°C temperature, for 100 mg l-1 initial dye concentration. The equilibrium and kinetic study revealed that the experimental data fitted suitably the Freundlich isotherm and Pseudo second order kinetic model. Thermodynamic analysis proved that adsorption system in this study was spontaneous, feasible and endothermic in nature.

Preparation of molecularly imprinted solid-phase microextraction fiber for the selective removal and extraction of the antiviral drug abacavir in environmental and biological matrices.

PubMed

Terzopoulou, Zoi; Papageorgiou, Myrsini; Kyzas, George Z; Bikiaris, Dimitrios N; Lambropoulou, Dimitra A

2016-03-24

In the present study, a molecularly imprinted solid-phase microextraction fiber (MIP-SPMEf) was synthesized and applied for the selective removal and extraction of the antiviral drug, abacavir (ABA). Morphology and structure characterization of fibers were performed by scanning electron microscopy and Fourier transform infrared spectra, respectively. The effects on the adsorption behavior of the process parameters were studied and the equilibrium data were fitted by the Langmuir, Freundlich and Langmuir-Freundlich models. The maximum adsorption capability (Qmax) was determined by Langmuir- Freundlich model and was 149 mg/g for MIP-SPMEf. In the next step, SPME methodology followed by liquid desorption and liquid chromatography with mass spectrometry (LC/MS) has been developed and evaluated for the determination of the target compound in environmental and biological matrices (surface waters, wastewaters and urine). Parameters that could influence SPME efficiency were investigated. Then, optimization of stirring speed, extraction time and salt content was carried out by using a central composite design (CCD) and response surface methodology (RSM). A quadratic model between dependent and independent variables was built. Under the optimum conditions (extraction time 40 min, stirring rate 650 rpm and salt content 0.3% NaCl w/v) the validated method presented a high sensitivity and selectivity with LODs and LOQs in the range of 10.1-13.6 and 33.3-43.9 ng/L, respectively. The developed method was successfully applied to the analysis of ABA in real samples. The percentage extraction efficiency ranged from 88 to 99% revealing good accuracy and absence of matrix effects. Copyright © 2016 Elsevier B.V. All rights reserved.

Breakthrough behavior of granular ferric hydroxide (GFH) fixed-bed adsorption filters: modeling and experimental approaches.

PubMed

Sperlich, Alexander; Werner, Arne; Genz, Arne; Amy, Gary; Worch, Eckhard; Jekel, Martin

2005-03-01

Breakthrough curves (BTC) for the adsorption of arsenate and salicylic acid onto granulated ferric hydroxide (GFH) in fixed-bed adsorbers were experimentally determined and modeled using the homogeneous surface diffusion model (HSDM). The input parameters for the HSDM, the Freundlich isotherm constants and mass transfer coefficients for film and surface diffusion, were experimentally determined. The BTC for salicylic acid revealed a shape typical for trace organic compound adsorption onto activated carbon, and model results agreed well with the experimental curves. Unlike salicylic acid, arsenate BTCs showed a non-ideal shape with a leveling off at c/c0 approximately 0.6. Model results based on the experimentally derived parameters over-predicted the point of arsenic breakthrough for all simulated curves, lab-scale or full-scale, and were unable to catch the shape of the curve. The use of a much lower surface diffusion coefficient D(S) for modeling led to an improved fit of the later stages of the BTC shape, pointing on a time-dependent D(S). The mechanism for this time dependence is still unknown. Surface precipitation was discussed as one possible removal mechanism for arsenate besides pure adsorption interfering the determination of Freundlich constants and D(S). Rapid small-scale column tests (RSSCT) proved to be a powerful experimental alternative to the modeling procedure for arsenic.

APTES-modified mesoporous silicas as the carriers for poorly water-soluble drug. Modeling of diflunisal adsorption and release

NASA Astrophysics Data System (ADS)

Geszke-Moritz, Małgorzata; Moritz, Michał

2016-04-01

Four mesoporous siliceous materials such as SBA-16, SBA-15, PHTS and MCF functionalized with (3-aminopropyl)triethoxysilane were successfully prepared and applied as the carriers for poorly water-soluble drug diflunisal. Several techniques including nitrogen sorption analysis, XRD, TEM, FTIR and thermogravimetric analysis were employed to characterize mesoporous matrices. Adsorption isotherms were analyzed using Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models. In order to find the best-fit isotherm for each model, both linear and nonlinear regressions were carried out. The equilibrium data were best fitted by the Langmuir isotherm model revealing maximum adsorption capacity of 217.4 mg/g for aminopropyl group-modified SBA-15. The negative values of Gibbs free energy change indicated that the adsorption of diflunisal is a spontaneous process. Weibull release model was employed to describe the dissolution profile of diflunisal. At pH 4.5 all prepared mesoporous matrices exhibited the improvement of drug dissolution kinetics as compared to the dissolution rate of pure diflunisal.

Utilization of oil palm biodiesel solid residue as renewable sources for preparation of granular activated carbon by microwave induced KOH activation.

PubMed

Foo, K Y; Hameed, B H

2013-02-01

In this work, preparation of granular activated carbon from oil palm biodiesel solid residue, oil palm shell (PSAC) by microwave assisted KOH activation has been attempted. The physical and chemical properties of PSAC were characterized using scanning electron microscopy, volumetric adsorption analyzer and elemental analysis. The adsorption behavior was examined by performing batch adsorption experiments using methylene blue as dye model compound. Equilibrium data were simulated using the Langmuir, Freundlich and Temkin isotherm models. Kinetic modeling was fitted to the pseudo-first-order, pseudo-second-order and Elovich kinetic models, while the adsorption mechanism was determined using the intraparticle diffusion and Boyd equations. The result was satisfactory fitted to the Langmuir isotherm model with a monolayer adsorption capacity of 343.94mg/g at 30°C. The findings support the potential of oil palm shell for preparation of high surface area activated carbon by microwave assisted KOH activation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Modeling of boldine alkaloid adsorption onto pure and propyl-sulfonic acid-modified mesoporous silicas. A comparative study.

PubMed

Geszke-Moritz, Małgorzata; Moritz, Michał

2016-12-01

The present study deals with the adsorption of boldine onto pure and propyl-sulfonic acid-functionalized SBA-15, SBA-16 and mesocellular foam (MCF) materials. Siliceous adsorbents were characterized by nitrogen sorption analysis, transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared (FT-IR) spectroscopy and thermogravimetric analysis. The equilibrium adsorption data were analyzed using the Langmuir, Freundlich, Redlich-Peterson, and Temkin isotherms. Moreover, the Dubinin-Radushkevich and Dubinin-Astakhov isotherm models based on the Polanyi adsorption potential were employed. The latter was calculated using two alternative formulas including solubility-normalized (S-model) and empirical C-model. In order to find the best-fit isotherm, both linear regression and nonlinear fitting analysis were carried out. The Dubinin-Astakhov (S-model) isotherm revealed the best fit to the experimental points for adsorption of boldine onto pure mesoporous materials using both linear and nonlinear fitting analysis. Meanwhile, the process of boldine sorption onto modified silicas was described the best by the Langmuir and Temkin isotherms using linear regression and nonlinear fitting analysis, respectively. The values of adsorption energy (below 8kJ/mol) indicate the physical nature of boldine adsorption onto unmodified silicas whereas the ionic interactions seem to be the main force of alkaloid adsorption onto functionalized sorbents (energy of adsorption above 8kJ/mol). Copyright © 2016 Elsevier B.V. All rights reserved.

Studies on Thorium Adsorption Characteristics upon Activated Titanium Hydroxide Prepared from Rosetta Ilmenite Concentrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gado, M, E-mail: parq28@yahoo.com; Zaki, S

2016-01-01

The titanium hydroxide prepared from Rosetta ilmenite concentrate has been applied for Th (IV) adsorption from its acid aqueous solutions. The prepared hydroxide is first characterized by both Fourier transform infrared (FT-IR) spectrum and thermogravimetric analysis. The relevant factors affecting the adsorption process have been studied. The obtained equilibrium data fits well with the Langmuir isotherm rather than Freundlich isotherm, while the adsorption kinetic data follow the pseudo-second order model. The different thermodynamic parameters have also been calculated and indicate that the adsorption process is spontaneous.

Comparative sorption, desorption and leaching potential of aminocyclopyrachlor and picloram

USDA-ARS?s Scientific Manuscript database

Aminocyclopyrachlor and picloram sorption, desorption and leaching potential were investigated in three soils from Minnesota and Hawaii. Aminocyclopyrachlor and picloram sorption fit the Freundlich equation and was independent of concentration for aminocyclopyrachlor (1/n = 1), but not for picloram ...

Biosorption Behavior of Ciprofloxacin onto Enteromorpha prolifera: Isotherm and Kinetic Studies.

PubMed

Wu, Shaoling; Li, Yanhui; Zhao, Xindong; Du, Qiuju; Wang, Zonghua; Xia, Yanzhi; Xia, Linhua

2015-01-01

The studies aimed at the feasibility of using Enteromorpha prolifera for the removal of ciprofloxacin from aqueous solutions. Batch experiments were carried out for the biosorption of ciprofloxacin onto Enteromorpha prolifera. The factors affecting the biosorption process such as the initial concentration, dosage, pH and the contact time were studied. Enteromorpha prolifera exhibited a maximum biosorption capacity of 21.7 mg/g. The pseudo-second-order kinetic model described the ciprofloxacin biosorption process with a good fitting. The optimum pH of ciprofloxacin adsorbed by Enteromorpha prolifera was 10. Biosorption equilibrium studies demonstrated that the biosorption followed Freundlich isotherm model, which implied a heterogeneous biosorption phenomenon.

Recyclable nanoscale zero-valent iron-based magnetic polydopamine coated nanomaterials for the adsorption and removal of phenanthrene and anthracene

NASA Astrophysics Data System (ADS)

Li, Jing; Zhou, Qingxiang; Liu, Yongli; Lei, Man

2017-12-01

In this study, nanoscale zero-valent iron nanoparticles (NZVIs) were coated with silica and polydopamine using a two-step process. The coated nanoparticles were applied as adsorbents for removal of two common polycyclic aromatic hydrocarbons pollutants, phenanthrene (PHE) and anthracene (ANT) from aqueous system. Adsorption kinetics followed a pseudo-second-order model. Isotherms and thermodynamics were investigated and the results indicated that the adsorption process fit best to the Freundlich model and exhibited the characteristics of an exothermal physical adsorption process. Owing to their superparamagnetic characteristics and stability, these adsorbents could be easily collected and recycled for reuse.

Water adsorption on goethite: Application of multilayer adsorption models

NASA Astrophysics Data System (ADS)

Hatch, C. D.; Tumminello, R.; Meredith, R.

2016-12-01

Adsorbed water on the surface of atmospheric mineral dust has recently been shown to significantly affect the ability of mineral dust aerosol to act as cloud condensation nuclei. We have studied water adsorption as a function of relative humidity (RH) on goethite (α-FeO(OH)), a common component of atmospheric mineral dust. The goethite surface area and particle size was determined using BET analysis and with N2 as an adsorbate and scanning electron microscopy, respectively. Water adsorption on the sample was monitored using horizontal attenuated total reflectance Fourier transform infrared (HATR-FTIR) spectroscopy equipped with a flow cell. Water content was determined using Beer's law and the optical constants for bulk water. The results were analyzed using Type II adsorption isotherms to model multilayer adsorption, including BET (Brunauer, Emmet and Teller), FHH (Frenkel, Halsey and Hill) and Freundlich. BET fits to experimental data provide parameters of monolayer coverage, while the FHH and Freundlich isotherms provide insights into multilayer adsorption mechanisms. Results indicate that goethite contains 5% H2O by mass at 50% RH, which increases to 12% by mass at 90% RH. Adsorption parameters and experimental results will be presented.

Removal of Pb (II) Ions from Aqueous Solutions by Cladophora rivularis (Linnaeus) Hoek

PubMed Central

Jafari, Naser; Senobari, Zoreh

2012-01-01

Biosorption of Pb(II) using Cladophora rivularis was examined as a function of initial pH heavy metal concentration and temperature. The optimum pH value for the biosorption of lead was 4.0. The adsorption equilibriums were well described by Langmuir and Freundlich isotherm models and it was implied by the results that the C. rivularis biomass is suitable for the development of efficient biosorbent in order to remove Pb(II) from wastewater and to recover it. The high values of correlation coefficient (R 2 = 0.984) demonstrate equilibrium data concerning algal biomass, which is well fitted in Freundlich isotherms model equations. The dimensionless parameter R L is found in the range of 0.0639 to 0.1925 (0 < R L < 1), which confirms the favorable biosorption process. Fourier transform infra-red (FTIR) spectroscopy of C. rivularis was used to reveal the main function groups of biosorption, which were hydroxyl, amine groups, C–H stretching vibrations of –CH3 and –CH2, and complexation with functional groups. All these results suggest that C. rivularis can be used effectively for removal of Pb(II). PMID:22629198

Isotherm investigation for the sorption of fluoride onto Bio-F: comparison of linear and non-linear regression method

NASA Astrophysics Data System (ADS)

Yadav, Manish; Singh, Nitin Kumar

2017-12-01

A comparison of the linear and non-linear regression method in selecting the optimum isotherm among three most commonly used adsorption isotherms (Langmuir, Freundlich, and Redlich-Peterson) was made to the experimental data of fluoride (F) sorption onto Bio-F at a solution temperature of 30 ± 1 °C. The coefficient of correlation (r2) was used to select the best theoretical isotherm among the investigated ones. A total of four Langmuir linear equations were discussed and out of which linear form of most popular Langmuir-1 and Langmuir-2 showed the higher coefficient of determination (0.976 and 0.989) as compared to other Langmuir linear equations. Freundlich and Redlich-Peterson isotherms showed a better fit to the experimental data in linear least-square method, while in non-linear method Redlich-Peterson isotherm equations showed the best fit to the tested data set. The present study showed that the non-linear method could be a better way to obtain the isotherm parameters and represent the most suitable isotherm. Redlich-Peterson isotherm was found to be the best representative (r2 = 0.999) for this sorption system. It is also observed that the values of β are not close to unity, which means the isotherms are approaching the Freundlich but not the Langmuir isotherm.

Sorption isotherm and kinetic modeling of aniline on Cr-bentonite.

PubMed

Zheng, Hong; Liu, Donghong; Zheng, Yan; Liang, Shuping; Liu, Zhe

2009-08-15

In this paper, the sorption characteristics of aniline on Cr-bentonite prepared using synthetic wastewater containing chromium was investigated in a batch system at 30 degrees C. The effects of relevant parameters, such as pH value of solution, adsorbent dosage and initial aniline concentration were examined. The experimental data were analyzed by the Langmuir and Freundlich, and Temkin models of sorption. The sorption isotherm data were fitted well to Langmuir isotherm and the monolayer sorption capacity was found to be 21.60 mg/g at 30 degrees C. Dubinin-Redushkevich (D-R) isotherm was applied to describe the nature of aniline uptake and it was found that it occurred chemically. The kinetic data obtained at different concentrations were analyzed using a pseudo first-order, pseudo second-order kinetic equation and intraparticle diffusion model. The experimental data fitted very well the pseudo second-order kinetic model. Intraparticle diffusion affects aniline uptake. The results indicate that there is significant potential for Cr-bentonite as an adsorbent material for aniline removal from aqueous solutions.

Adsorption of tobacco-specific nitrosamine 4-(methylnitrosamino) -1- (3-pyridyl)-1-butanone from aqueous solution with graphene aerogel

NASA Astrophysics Data System (ADS)

Xu, T. G.; Shi, R.; Lu, N.; Zhang, J.; Bai, R. S.; Yang, Z. D.; Zhou, J.

2018-03-01

The adsorption behavior of graphene aerogel in the 4-(Methylnitrosamino)-1-(3-pryidyl)-1-butanone (NNK) aqueous solution was studied. The adsorption kinetics fitted pseudo-second-order model with the rate constant (k2) of 0.154 g/mg·h. The adsorption isotherm was investigated and fitted Langmuir and Freundlich models well, and the maximum adsorption capacity (qm) was 59.66 mg/g estimated from Langmuir isotherm. Thermodynamic result indicated that the process of adsorption of NNK onto graphene aerogel was spontaneous and exothermic. Higher pH solution was favorable for NNK adsorption on graphene aerogel. The adsorption for NNK on graphene aerogel arose from the π-π interaction between them, and the high adsorption efficiency was resulted from the -NO2 functional groups. The capability of graphene aerogel was maintained after repeated absorption-desorption cycles, which was benefit for convenient separating and recycling of graphene aerogel.

Sorption of Ochratoxin A from Aqueous Solutions Using β-Cyclodextrin-Polyurethane Polymer

PubMed Central

Appell, Michael; Jackson, Michael A.

2012-01-01

The ability of a cyclodextrin-polyurethane polymer to remove ochratoxin A from aqueous solutions was examined by batch rebinding assays. The results from the aqueous binding studies were fit to two parameter models to gain insight into the interaction of ochratoxin A with the nanosponge material. The ochratoxin A sorption data fit well to the heterogeneous Freundlich isotherm model. The polymer was less effective at binding ochratoxin A in high pH buffer (9.5) under conditions where ochratoxin A exists predominantly in the dianionic state. Batch rebinding assays in red wine indicate the polymer is able to remove significant levels of ochratoxin A from spiked solutions between 1–10 μg·L−1. These results suggest cyclodextrin nanosponge materials are suitable to reduce levels of ochratoxin A from spiked aqueous solutions and red wine samples. PMID:22474569

Adsorption of phenolic compound by aged-refuse.

PubMed

Xiaoli, Chai; Youcai, Zhao

2006-09-01

The adsorption of phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol by aged-refuse has been studied. Adsorption isotherms have been determined for phenol, 2-chlorophenol, 4-chlorophenol and 2,4-dichlorophenol and the data fits well to the Freundlich equation. The chlorinated phenols are absorbed more strongly than the phenol and the adsorption capacity has an oblivious relationship with the numbers and the position of chlorine subsistent. The experiment data suggests that both the partition function and the chemical adsorption involve in the adsorption process. Pseudo-first-order and pseudo-second-order model were applied to investigate the kinetics of the adsorption and the results show that it fit the pseudo-second-order model. More than one step involves in the adsorption process and the overall rate of the adsorption process appears to be controlled by the chemical reaction. The thermodynamic analysis indicates that the adsorption is spontaneous and endothermic.

Adsorption of direct dyes from aqueous solutions by carbon nanotubes: determination of equilibrium, kinetics and thermodynamics parameters.

PubMed

Kuo, Chao-Yin; Wu, Chung-Hsin; Wu, Jane-Yii

2008-11-15

This study examined the feasibility of removing direct dyes C.I. Direct Yellow 86 (DY86) and C.I. Direct Red 224 (DR224) from aqueous solutions using carbon nanotubes (CNTs). The effects of dye concentration, CNT dosage, ionic strength and temperature on adsorption of direct dyes by CNTs were also evaluated. Pseudo second-order, intraparticle diffusion and Bangham models were adopted to evaluate experimental data and thereby elucidate the kinetic adsorption process. Additionally, this study used the Langmuir, Freundlich, Dubinin and Radushkevich (D-R) and Temkin isotherms to describe equilibrium adsorption. The adsorption percentage of direct dyes increased as CNTs dosage, NaCl addition and temperature increased. Conversely, the adsorption percentage of direct dyes decreased as dye concentration increased. The pseudo second-order model best represented adsorption kinetics. Based on the regressions of intraparticle diffusion and Bangham models, experimental data suggest that the adsorption of direct dyes onto CNTs involved intraparticle diffusion, but that was not the only rate-controlling step. The equilibrium adsorption of DR86 is best fitted in the Freundlich isotherm and that of DR224 was best fitted in the D-R isotherm. The capacity of CNTs to adsorb DY86 and DR224 was 56.2 and 61.3 mg/g, respectively. For DY86, enthalpy (DeltaH(0)) and entropy (DeltaS(0)) were 13.69 kJ/mol and 139.51 J/mol K, respectively, and those for DR224 were 24.29 kJ/mol and 172.06 J/mol K, respectively. The values of DeltaH(0), DeltaG(0) and E all indicate that the adsorption of direct dyes onto CNTs was a physisorption process.

Sorption of fluoride using chemically modified Moringa oleifera leaves

NASA Astrophysics Data System (ADS)

Dan, Shabnam; Chattree, Amit

2018-05-01

Contamination of drinking water due to fluoride is a severe health hazard problem. Excess of fluoride (> 1.5 mg/L) in drinking water is harmful to human health. Various treatment technologies for removing fluoride from groundwater have been investigated. The present study showed that the leaves of Moringa oleifera, a herbal plant is an effective adsorbent for the removal of fluoride from aqueous solution. Acid treated Moringa oleifera leaves powder showed good adsorption capacity than alkali treated Moringa oleifera leaves powder. Batch sorptive defluoridation was conducted under the variable experimental condition such as pH, contact time, adsorbent dose and initial fluoride ion concentration. Maximum defluoridation was achieved at pH 1. The percentage of fluoride removal increases with adsorbent dose. The equilibrium sorption data were fitted into Langmuir, Freundlich and Temkin isotherms. Of the three adsorption isotherms, the R 2 value of Langmuir isotherm model was the highest. The maximum monolayer coverage ( Q max) from Langmuir isotherm model was determined to be 1.1441 mg/g, the separation factor indicating a favorable sorption experiment is 0.035. It was also discovered that the adsorption did not conform to the Freundlich adsorption isotherm. The heat of sorption process was estimated from Temkin Isotherm model to be - 0.042 J/mol which vividly proved that the adsorption experiment followed a physical process.

Citric acid modified kenaf core fibres for removal of methylene blue from aqueous solution.

PubMed

Sajab, Mohd Shaiful; Chia, Chin Hua; Zakaria, Sarani; Jani, Saad Mohd; Ayob, Mohd Khan; Chee, Kah Leong; Khiew, Poi Sim; Chiu, Wee Siong

2011-08-01

Chemically modified kenaf core fibres were prepared via esterification in the presence of citric acid (CA). The adsorption kinetics and isotherm studies were carried out under different conditions to examine the adsorption efficiency of CA-treated kenaf core fibres towards methylene blue (MB). The adsorption capacity of the kenaf core fibres increased significantly after the citric acid treatment. The values of the correlation coefficients indicated that the Langmuir isotherm fitted the experimental data better than the Freundlich isotherm. The maximum adsorption capacity of the CA-treated kenaf core fibres was found to be 131.6mg/g at 60°C. Kinetic models, pseudo-first-order, pseudo-second-order and intraparticle diffusion, were employed to describe the adsorption mechanism. The kinetic data were found to fit pseudo-second-order model equation as compared to pseudo-first-order model. The adsorption of MB onto the CA-treated kenaf core fibres was spontaneous and endothermic. Copyright © 2011 Elsevier Ltd. All rights reserved.

Progress in the preparation and application of modified biochar for improved contaminant removal from water and wastewater.

PubMed

Ahmed, Mohammad Boshir; Zhou, John L; Ngo, Huu H; Guo, Wenshan; Chen, Mengfang

2016-08-01

Modified biochar (BC) is reviewed in its preparation, functionality, applications and regeneration. The nature of precursor materials, preparatory conditions and modification methods are key factors influencing BC properties. Steam activation is unsuitable for improving BC surface functionality compared with chemical modifications. Alkali-treated BC possesses the highest surface functionality. Both alkali modified BC and nanomaterial impregnated BC composites are highly favorable for enhancing the adsorption of different contaminants from wastewater. Acidic treatment provides more oxygenated functional groups on BC surfaces. The Langmuir isotherm model provides the best fit for sorption equilibria of heavy metals and anionic contaminants, while the Freundlich isotherm model is the best fit for emerging contaminants. The pseudo 2(nd) order is the most appropriate model of sorption kinetics for all contaminants. Future research should focus on industry-scale applications and hybrid systems for contaminant removal due to scarcity of data. Copyright © 2016 Elsevier Ltd. All rights reserved.

Activated bauxite waste as an adsorbent for removal of Acid Blue 92 from aqueous solutions.

PubMed

Norouzi, Sh; Badii, Kh; Doulati Ardejani, F

2010-01-01

Bauxite waste, known as red mud, is produced in some industrial processes, such as aluminum production process. In this process, the waste material is produced from leached bauxite as a by product. In this research, the removal of Acid Blue 92 (AB92) dye was investigated from aqueous solution onto the activated bauxite waste (red mud) in a batch equilibration system. Besides, the influences of pH, adsorbent dosage, contact time, initial concentration of dye and temperature have been considered. It was found that the OH group is an effective functional group for the adsorption process. The intensity of the peaks correspond to OH group has been significantly climbed after the activation process. The adsorption kinetics of AB92 can be well described by the pseudo-second-order reaction model. Based on the isotherm data obtained from the fittings of the adsorption kinetics, the Langmuir model appears to fit the adsorption process better than the Freundlich and Brunauer-Emmett-Teller (BET) models.

Competitive adsorption of Pb(II), Cu(II), and Zn(II) ions onto hydroxyapatite-biochar nanocomposite in aqueous solutions

NASA Astrophysics Data System (ADS)

Wang, Yu-Ying; Liu, Yu-Xue; Lu, Hao-Hao; Yang, Rui-Qin; Yang, Sheng-Mao

2018-05-01

A hydroxyapatite-biochar nanocomposite (HAP-BC) was successfully fabricated and its physicochemical properties characterized. The analyses showed that HAP nanoparticles were successfully loaded on the biochar surface. The adsorption of Pb(II), Cu(II), and Zn(II) by HAP-BC was systematically studied in single and ternary metal systems. The results demonstrated that pH affects the adsorption of heavy metals onto HAP-BC. Regarding the adsorption kinetics, the pseudo-second-order model showed the best fit for all three heavy metal ions on HAP-BC. In both single and ternary metal ion systems, the adsorption isotherm of Pb(II) by HAP-BC followed Langmuir model, while those of Cu(II) and Zn(II) fitted well with Freundlich model. The maximum adsorption capacity for each tested metal by HAP-BC was higher than that of pristine rice straw biochar (especially for Pb(II)) or those of other reported adsorbents. Therefore, HAP-BC could explore as a new material for future application in heavy metal removal.

Effective adsorption of phenolic compound from aqueous solutions on activated semi coke

NASA Astrophysics Data System (ADS)

Gao, Xiaoming; Dai, Yuan; Zhang, Yu; Fu, Feng

2017-03-01

Activated Semi coke was prepared by KOH activation and employed as adsorbent to study adsorption function of phenolic compound from aqueous solutions. The adsorption result showed that the adsorption capacity of the activated semi coke for phenolic compound increased with contact time and adsorbent dosage, and slightly affected by temperature. The surface structure property of the activated semi coke was characterized by N2 adsorption, indicating that the activated semi coke was essentially macroporous, and the BET surface area was 347.39 m2 g-1. Scanning electron microscopy indicated that the surface of the activated semi coke had a high developed pore. The adsorption kinetics were investigated according to pseudofirst order, pseudosecond order and intraparticle diffusion, and the kinetics data were fitted by pseudosecond order model, and intraparticle diffusion was not the only rate-controlling step. Adsorption isotherm was studied by Langmuir, Freundlich, Temkin, Redlich-Peterson, Sips and Toth models. The result indicated that adsorption isotherm data could fit well with Langmuir, Redlich-Peterson, Sips and Toth models.

Zeolite formation from coal fly ash and heavy metal ion removal characteristics of thus-obtained Zeolite X in multi-metal systems.

PubMed

Jha, Vinay Kumar; Nagae, Masahiro; Matsuda, Motohide; Miyake, Michihiro

2009-06-01

Zeolitic materials have been prepared from coal fly ash as well as from a SiO(2)-Al(2)O(3) system upon NaOH fusion treatment, followed by subsequent hydrothermal processing at various NaOH concentrations and reaction times. During the preparation process, the starting material initially decomposed to an amorphous form, and the nucleation process of the zeolite began. The carbon content of the starting material influenced the formation of the zeolite by providing an active surface for nucleation. Zeolite A (Na-A) was transformed into zeolite X (Na-X) with increasing NaOH concentration and reaction time. The adsorption isotherms of the obtained Na-X based on the characteristics required to remove heavy ions such as Ni(2+), Cu(2+), Cd(2+) and Pb(2+) were examined in multi-metal systems. Thus obtained experimental data suggests that the Langmuir and Freundlich models are more accurate compared to the Dubinin-Kaganer-Radushkevich (DKR) model. However, the sorption energy obtained from the DKR model was helpful in elucidating the mechanism of the sorption process. Further, in going from a single- to multi-metal system, the degree of fitting for the Freundlich model compared with the Langmuir model was favored due to its basic assumption of a heterogeneity factor. The Extended-Langmuir model may be used in multi-metal systems, but gives a lower value for equilibrium sorption compared with the Langmuir model.

Modeling of adsorption isotherms of phenol and chlorophenols onto granular activated carbon. Part I. Two-parameter models and equations allowing determination of thermodynamic parameters.

PubMed

Hamdaoui, Oualid; Naffrechoux, Emmanuel

2007-08-17

The adsorption equilibrium isotherms of five phenolic compounds from aqueous solutions onto granular activated carbon (GAC) were studied and modeled. Phenol (Ph), 2-chlorophenol (2-CP), 4-chlorophenol (4-CP), 2,4-dichlorophenol (DCP), and 2,4,6-trichlorophenol (TCP) were chosen for the adsorption tests. To predict the adsorption isotherms and to determine the characteristic parameters for process design, seven isotherm models: Langmuir (five linear forms), Freundlich, Elovich, Temkin, Fowler-Guggenheim, Kiselev, and Hill-de Boer models were applied to experimental data. The results reveal that the adsorption isotherm models fitted the data in the order: Fowler-Guggenheim>Hill-de Boer>Temkin>Freundlich>Kiselev>Langmuir isotherms. Adsorption isotherms modeling shows that the interaction of phenolic compounds with activated carbon surface is localized monolayer adsorption, that is adsorbed molecules are adsorbed at definite, localized sites. Each site can accommodate only one molecule. The interaction among adsorbed molecules is repulsive and there is no association between them, adsorption is carried out on energetically different sites and is an exothermic process. Uptake of phenols increases in the order Ph<2-CP<4-CP

Dye adsorption into transition metal-doped zinc oxide nanoparticles supported on natural zeolites to solve wastewater issue

NASA Astrophysics Data System (ADS)

Indra Pratiwi, Margaretha; Afifah, Nur; Saleh, Rosari

2017-03-01

In this work, Fe-doped zinc oxide/natural zeolite (Fe:ZnO/NZ) nanocomposites were prepared using the co-precipitation method with various NZ amounts. The nanocomposites were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis and thermogravimetric analysis (TGA). The nanocomposites were used to remove methylene blue (MB) dye from an aqueous solution. The effect of various NZ amounts and initial MB concentration were tested. The Pseudo-first-order and pseudo-second-order kinetic models were used to explain the adsorption mechanism. The Langmuir and the Freundlich isotherm models were used to fit the adsorption isotherms of the nanocomposites.

Recyclable nanoscale zero-valent iron-based magnetic polydopamine coated nanomaterials for the adsorption and removal of phenanthrene and anthracene

PubMed Central

Li, Jing; Zhou, Qingxiang; Liu, Yongli; Lei, Man

2017-01-01

Abstract In this study, nanoscale zero-valent iron nanoparticles (NZVIs) were coated with silica and polydopamine using a two-step process. The coated nanoparticles were applied as adsorbents for removal of two common polycyclic aromatic hydrocarbons pollutants, phenanthrene (PHE) and anthracene (ANT) from aqueous system. Adsorption kinetics followed a pseudo-second-order model. Isotherms and thermodynamics were investigated and the results indicated that the adsorption process fit best to the Freundlich model and exhibited the characteristics of an exothermal physical adsorption process. Owing to their superparamagnetic characteristics and stability, these adsorbents could be easily collected and recycled for reuse. PMID:28179954

[Application of classical isothermal adsorption models in heavy metal ions/ diatomite system and related problems].

PubMed

Zhu, Jian; Wu, Qing-Ding; Wang, Ping; Li, Ke-Lin; Lei, Ming-Jing; Zhang, Wei-Li

2013-11-01

In order to fully understand adsorption nature of Cu2+, Zn2+, Pb2+, Cd2+, Mn2+, Fe3+ onto natural diatomite, and to find problems of classical isothermal adsorption models' application in liquid/solid system, a series of isothermal adsorption tests were conducted. As results indicate, the most suitable isotherm models for describing adsorption of Pb2+, Cd2+, Cu2+, Zn2+, Mn2+, Fe3+ onto natural diatomite are Tenkin, Tenkin, Langmuir, Tenkin, Freundlich and Freundlich, respectively, the adsorption of each ion onto natural diatomite is mainly a physical process, and the adsorption reaction is favorable. It also can be found that, when using classical isothermal adsorption models to fit the experimental data in liquid/solid system, the equilibrium adsorption amount q(e) is not a single function of ion equilibrium concentration c(e), while is a function of two variables, namely c(e) and the adsorbent concentration W0, q(e) only depends on c(e)/W(0). Results also show that the classical isothermal adsorption models have a significant adsorbent effect, and their parameter values are unstable, the simulation values of parameter differ greatly from the measured values, which is unhelpful for practical use. The tests prove that four-adsorption-components model can be used for describing adsorption behavior of single ion in nature diatomite-liquid system, its parameters k and q(m) have constant values, which is favorable for practical quantitative calculation in a given system.

SORPTION AND DESORPTION BY IDEAL TWO-COMPARTMENT SYSTEMS: UNUSUAL BEHAVIOR AND DATA INTERPRETATION PROBLEMS

EPA Science Inventory

This paper presents an evaluation of the results of fitting curves to isotherm and kinetic data for idealized two-compartment systems of soil or sediment. Data were produced by numerically solving sets of Freundlich isotherm and first-order kinetics equations for mixtures of up ...

Biosorption of Congo Red from aqueous solution onto burned root of Eichhornia crassipes biomass

NASA Astrophysics Data System (ADS)

Roy, Tapas Kumar; Mondal, Naba Kumar

2017-07-01

Biosorption is becoming a promising alternative to replace or supplement the present dye removal processes from dye containing waste water. In this work, adsorption of Congo Red (CR) from aqueous solution on burned root of Eichhornia crassipes ( BREC) biomass was investigated. A series of batch experiments were performed utilizing BREC biomass to remove CR dye from aqueous systems. Under optimized batch conditions, the BREC could remove up to 94.35 % of CR from waste water. The effects of operating parameters such as initial concentration, pH, adsorbent dose and contact time on the adsorption of CR were analyzed using response surface methodology. The proposed quadratic model for central composite design fitted very well to the experimental data. Response surface plots were used to determine the interaction effects of main factors and optimum conditions of the process. The optimum adsorption conditions were found to be initial CR concentration = 5 mg/L-1, pH = 7, adsorbent dose = 0.125 g and contact time = 45 min. The experimental isotherms data were analyzed using Langmuir, Freundlich, Temkin and Dubinin-Radushkevich (D-R) isotherm equations and the results indicated that the Freundlich isotherm showed a better fit for CR adsorption. Thermodynamic parameters were calculated from Van't Hoff plot, confirming that the adsorption process was spontaneous and exothermic. The high CR adsorptive removal ability and regeneration efficiency of this adsorbent suggest its applicability in industrial/household systems and data generated would help in further upscaling of the adsorption process.

Evaluation of carbon-based nanosorbents synthesised by ethylene decomposition on stainless steel substrates as potential sequestrating materials for nickel ions in aqueous solution.

PubMed

Lee, X J; Lee, L Y; Foo, L P Y; Tan, K W; Hassell, D G

2012-01-01

The present work covers the preparation of carbon-based nanosorbents by ethylene decomposition on stainless steel mesh without the use of external catalyst for the treatment of water containing nickel ions (Ni2+). The reaction temperature was varied from 650 to 850 degrees C, while reaction time and ethylene to nitrogen flow ratio were maintained at 30 min and 1:1 cm3/min, respectively. Results show that nanosorbents synthesised at a reaction temperature of 650 degrees C had the smallest average diameter (75 nm), largest BET surface area (68.95 m2/g) and least amount of impurity (0.98 wt.% Fe). A series of batch-sorption tests were performed to evaluate the effects of initial pH, initial metal concentration and contact time on Ni2+ removal by the nanosorbents. The equilibrium data fitted well to Freundlich isotherm. The kinetic data were best correlated to a pseudo second-order model indicating that the process was of chemisorption type. Further analysis by the Boyd kinetic model revealed that boundary layer diffusion was the controlling step. This primary study suggests that the prepared material with Freundlich constants compared well with those in the literature, is a promising sorbent for the sequestration of Ni2+ in aqueous solutions.

Removal of tetracycline from wastewater using pumice stone: equilibrium, kinetic and thermodynamic studies

PubMed Central

2014-01-01

In this study, pumice stone was used for the removal of tetracyline (TC) from aqueous solutions. It was characterized by XRD, FT-IR, SEM and BET analyses. Cation exchange capacity of pumice stone was found to be 9.9 meq/100 g. Effect of various parameters such as solution pH (2–11), adsorbent dosage (0.5-10 g/L), contact time (2.5-120 min), initial TC concentration (5–300 mg/L) and temperature (20–50°C) on TC adsorption onto pumice was investigated. Also the adsorption of TC on pumice stone was studied as a function of Na+ and Cu2+ cations changing pH from 2 to 11 using batch experiments. The best removal efficiency performance was exhibited at adsorbent dosage 10 g/L, pH 3, contact time 120 min. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) isotherm models were applied to the equilibrium data. The result has shown that the adsorption was favorable, physicochemical in nature and agrees well with Langmuir and Freundlich models. The maximum Langmuir adsorption capacity was found to be 20.02 mg/g. The adsorption behavior of TC on pumices stone was fitted well in the pseudo-second order kinetics model. Thermodynamic parameters calculated from the adsorption data at different temperature showed that the adsorption reaction was feasible, spontaneous and exothermic. PMID:24936305

A comparative examination of the adsorption mechanism of an anionic textile dye (RBY 3GL) onto the powdered activated carbon (PAC) using various the isotherm models and kinetics equations with linear and non-linear methods

NASA Astrophysics Data System (ADS)

Açıkyıldız, Metin; Gürses, Ahmet; Güneş, Kübra; Yalvaç, Duygu

2015-11-01

The present study was designed to compare the linear and non-linear methods used to check the compliance of the experimental data corresponding to the isotherm models (Langmuir, Freundlich, and Redlich-Peterson) and kinetics equations (pseudo-first order and pseudo-second order). In this context, adsorption experiments were carried out to remove an anionic dye, Remazol Brillant Yellow 3GL (RBY), from its aqueous solutions using a commercial activated carbon as a sorbent. The effects of contact time, initial RBY concentration, and temperature onto adsorbed amount were investigated. The amount of dye adsorbed increased with increased adsorption time and the adsorption equilibrium was attained after 240 min. The amount of dye adsorbed enhanced with increased temperature, suggesting that the adsorption process is endothermic. The experimental data was analyzed using the Langmuir, Freundlich, and Redlich-Peterson isotherm equations in order to predict adsorption isotherm. It was determined that the isotherm data were fitted to the Langmuir and Redlich-Peterson isotherms. The adsorption process was also found to follow a pseudo second-order kinetic model. According to the kinetic and isotherm data, it was found that the determination coefficients obtained from linear method were higher than those obtained from non-linear method.

Low cost biosorbent "banana peel" for the removal of phenolic compounds from olive mill wastewater: kinetic and equilibrium studies.

PubMed

Achak, M; Hafidi, A; Ouazzani, N; Sayadi, S; Mandi, L

2009-07-15

The aim of this work is to determine the potential of application of banana peel as a biosorbent for removing phenolic compounds from olive mill wastewaters. The effect of adsorbent dosage, pH and contact time were investigated. The results showed that the increase in the banana peel dosage from 10 to 30 g/L significantly increased the phenolic compounds adsorption rates from 60 to 88%. Increase in the pH to above neutrality resulted in the increase in the phenolic compounds adsorption capacity. The adsorption process was fast, and it reached equilibrium in 3-h contact time. The Freundlich and Langmuir adsorption models were used for mathematical description of the adsorption equilibrium and it was found that experimental data fitted very well to both Freundlich and Langmuir models. Batch adsorption models, based on the assumption of the pseudo-first-order, pseudo-second-order and intraparticle diffusion mechanism, showed that kinetic data follow closely the pseudo-second-order than the pseudo-first-order and intraparticle diffusion. Desorption studies showed that low pH value was efficient for desorption of phenolic compounds. These results indicate clearly the efficiency of banana peel as a low-cost solution for olive mill wastewaters treatment and give some preliminary elements for the comprehension of the interactions between banana peel as a bioadsorbent and the very polluting compounds from the olive oil industry.

Use of carbonised beet pulp carbon for removal of Remazol Turquoise Blue-G 133 from aqueous solution.

PubMed

Dursun, Arzu Y; Tepe, Ozlem; Dursun, Gülbeyi

2013-01-01

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g(-1)at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.

Exploring the interaction of silver nanoparticles with pepsin and its adsorption isotherms and kinetics.

PubMed

Li, Xiangrong; Wang, Kaiwei; Peng, Yanru

2018-04-25

The interaction of nanoparticles (NPs) with proteins is a topic of high relevance for the medical application of nanomaterials. In the study, a comprehensive investigation was performed for the binding properties of silver nanoparticles (AgNPs) to pepsin. The results indicate that the binding of AgNPs to pepsin may be a static quenching mechanism. Thermodynamic analysis reveals that AgNPs binds to pepsin is synergistically driven by enthalpy and entropy, and the major driving forces are hydrophobic and electrostatic interactions. Synchronous fluorescence spectroscopy shows that AgNPs may induce microenvironmental changes of pepsin. The hydrophobicity of Trp is increased while the hydrophility of Tyr is increased. The adsorption of pepsin on AgNPs was analyzed by Langmuir and Freundlich models, suggesting that the equilibrium adsorption data fit well with Freundlich model. The equilibrium adsorption data were modeled using the pseudo-first-order and pseudo-second-order kinetic equations. The results indicate that pseudo-second-order kinetic equation better describes the adsorption kinetics. The study provides an accurate and full basic data for clarifying the binding mechanism, adsorption isotherms and kinetic behaviors of AgNPs with pepsin. These fundamental works will provide some new insights into the safe and effective application of AgNPs in biological and medical areas. Copyright © 2018 Elsevier B.V. All rights reserved.

Batch sorption dynamics and equilibrium for the removal of lead ions from aqueous phase using activated carbon developed from coffee residue activated with zinc chloride.

PubMed

Boudrahem, F; Aissani-Benissad, F; Aït-Amar, H

2009-07-01

Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions. The influence of impregnation ratio (ZnCl2/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m2/g) and micropore volume (0.772 cm3/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio. Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 degrees C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others. Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl2 is a suitable activating agent for the preparation of high-porosity carbons.

Insights into the equilibrium, kinetic and thermodynamics of nickel removal by environmental friendly Lansium domesticum peel biosorbent.

PubMed

Lam, Yun Fung; Lee, Lai Yee; Chua, Song Jun; Lim, Siew Shee; Gan, Suyin

2016-05-01

Lansium domesticum peel (LDP), a waste material generated from the fruit consumption, was evaluated as a biosorbent for nickel removal from aqueous media. The effects of dosage, contact time, initial pH, initial concentration and temperature on the biosorption process were investigated in batch experiments. Equilibrium data were fitted by the Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models using nonlinear regression method with the best-fit model evaluated based on coefficient of determination (R(2)) and Chi-square (χ(2)). The best-fit isotherm was found to be the Langmuir model exhibiting R(2) very close to unity (0.997-0.999), smallest χ(2) (0.0138-0.0562) and largest biosorption capacity (10.1mg/g) at 30°C. Kinetic studies showed that the initial nickel removal was rapid with the equilibrium state established within 30min. Pseudo-second-order model was the best-fit kinetic model indicating the chemisorption nature of the biosorption process. Further data analysis by the intraparticle diffusion model revealed the involvement of several rate-controlling steps such as boundary layer and intraparticle diffusion. Thermodynamically, the process was exothermic, spontaneous and feasible. Regeneration studies indicated that LDP biosorbent could be regenerated using hydrochloric acid solution with up to 85% efficiency. The present investigation proved that LDP having no economic value can be used as an alternative eco-friendly biosorbent for remediation of nickel contaminated water. Copyright © 2016 Elsevier Inc. All rights reserved.

Adsorption potential of a modified activated carbon for the removal of nitrogen containing compounds from model fuel

NASA Astrophysics Data System (ADS)

Anisuzzaman, S. M.; Krishnaiah, D.; Alfred, D.

2018-02-01

The purpose of this study is to find the effect of the modified activated carbon (MAC) on the adsorption activity for nitrogen containing compounds (NCC) removal from model fuel. Modification of commercial activated carbon (AC) involved impregnation with different ratios of sulfuric acid solution. Pseudo-first and pseudo-second order kinetic models were applied to study the adsorption kinetics, while the adsorption isotherms were used for the evaluation of equilibrium data. All of the experimental data were analyzed using ultraviolet-visible spectroscopy after adsorption experiment between different concentration dosage of adsorbent and model fuel. It has been found that adsorption of NCC by MAC was best fit is the Langmuir isotherm for quinoline (QUI) and Freundlich isotherm for indole (IND) with a maximum adsorption capacity of 0.13 mg/g and 0.16 mg/g respectively. Based on the experimental data, pseudo-first order exhibited the best fit for QUI with linear regression (R2) ranges from 0.0.9777 to 0.9935 and pseudo-second order exhibited the best fit for IND with linear regression (R2) ranges from 0.9701 to 0.9962. From the adsorption isotherm and kinetic studies result proven that commercial AC shows great potential in removing nitrogen.

Removal of aniline and phenol from water using raw and aluminum hydroxide-modified diatomite.

PubMed

Wu, C D; Zhang, J Y; Wang, L; He, M H

2013-01-01

The feasibility of using raw diatomite and aluminum hydroxide-modified diatomite (Al-diatomite) for removal of aniline and phenol from water was investigated. Their physicochemical characteristics such as pHsolution, point of zero charge (pHPZC), surface area, Fourier transform infrared (FT-IR) and scanning electron microscopy was determined. After the raw diatomite was modified, the surface area of Al-diatomite increases from 26.67 to 82.65 m(2) g(-1). The pHPZC and pHsolution (10%) occurred around pH 5.2 and pH 8.6, respectively. The removal rates of aniline and phenol on diatomite and Al-diatomite decreased with increasing solution pH, while surface charge density decreased. The adsorption of aniline and phenol on diatomite presented a good fit to the Langmuir and Freundlich models, but the models are not fit to forecast the adsorption of aniline and phenol on Al-diatomite. The study indicated that electrostatic interaction was a dominating mechanism of aniline and phenol sorption onto Al-diatomite.

Nonlinear isotherm and kinetics of adsorption of copper from aqueous solutions on bentonite

NASA Astrophysics Data System (ADS)

Sadeghalvad, Bahareh; Khosravi, Sara; Azadmehr, Amir Reza

2016-11-01

Bentonite is one of the most significant of clay minerals that has been studied extensively due to its potential applications in removal of various environmental pollutants. This ability is related to its high ionic exchange capacity and high specific surface area. Copper is one of the important elements of non-ferrous metals found in industrial waste waters. In the present work, the removal of copper from aqueous solutions with Iranian bentonite (from Birjand area, southeastern Iran) used without any chemical pretreatment, was studied. The experimental results were fitted by adsorption isotherms equations with two or three parameters, which include Langmuir, Freundlich, Dubinin-Radushkevich (D-R), Redlich-Peterson, Khan, and Toth models. The best correlation coefficient ( r 2) is 0.9879 observed for Langmuir model, maximum adsorption capacity of bentonite was 55.71 mg/g. The first-order and pseudo-second-order kinetic equations were used to describe the kinetics of adsorption. The experimental data were well fitted by the pseudo-second-order kinetics.

Adsorption of Toluene and Paraxylene from Aqueous Solution Using Pure and Iron Oxide Impregnated Carbon Nanotubes: Kinetics and Isotherms Study

PubMed Central

Abbas, Aamir; Ihsanullah; Al-Baghli, Nadhir A. H.

2017-01-01

Multiwall carbon nanotubes (CNTs) and iron oxide impregnated carbon nanotubes (CNTs-iron oxide) were investigated for the adsorption of hazardous toluene and paraxylene (p-xylene) from aqueous solution. Pure CNTs were impregnated with iron oxides nanoparticles using wet impregnation technique. Various characterization techniques including thermogravimetric analysis, scanning electron microscopy, elemental dispersion spectroscopy, X-ray diffraction, and nitrogen adsorption analysis were used to study the thermal degradation, surface morphology, purity, and surface area of the materials. Batch adsorption experiments show that iron oxide impregnated CNTs have higher degree of removal of p-xylene (i.e., 90%) compared with toluene (i.e., 70%), for soaking time 2 h, with pollutant initial concentration 100 ppm, at pH 6 and shaking speed of 200 rpm at 25°C. Pseudo-second-order model provides better fitting for the toluene and p-xylene adsorption. Langmuir and Freundlich isotherm models demonstrate good fitting for the adsorption data of toluene and p-xylene. PMID:28386208

Blast furnace residues for arsenic removal from mining-contaminated groundwater.

PubMed

Carrillo-Pedroza, Fco Raúl; Soria-Aguilar, Ma de Jesús; Martínez-Luevanos, Antonia; Narvaez-García, Víctor

2014-01-01

In this work, blast furnace (BF) residues were well characterized and then evaluated as an adsorbent material for arsenic removal from a mining-contaminated groundwater. The adsorption process was analysed using the theories of Freundlich and Langmuir. BF residues were found to be an effective sorbent for As (V) ions. The modelling of adsorption isotherms by empirical models shows that arsenate adsorption is fitted by the Langmuir model, suggesting a monolayer adsorption of arsenic onto adsorbents. Arsenate adsorption onto BF residue is explained by the charge density surface affinity and by the formation of Fe (II) and Fe (III) corrosion products onto BF residue particles. The results indicate that BF residues represent an attractive low-cost absorbent option for the removal of arsenic in wastewater treatment.

Removal of herbicide paraquat from an aqueous solution by adsorption onto spent and treated diatomaceous earth.

PubMed

Tsai, W T; Hsien, K J; Chang, Y M; Lo, C C

2005-04-01

A spent diatomaceous earth from the beer brewery has been tentatively activated by sodium hydroxide at about 100 degrees C. The resulting product was used as a novel adsorbent for the adsorption of herbicide paraquat from an aqueous solution in a continuously stirred adsorber and batch flasks, respectively. The results showed that the adsorption process could be well described by the pseudo-second-order reaction model. From the view of the negatively charged surface of diatomaceous earth and cationic property of paraquat, the results were also reasonable to be explained by physical adsorption in the ion-exchange process under the effects of pH and temperature. Further, it was found that the Freundlich model appeared to fit the isotherm data better than the Langmuir model.

Behaviors and kinetics of toluene adsorption-desorption on activated carbons with varying pore structure.

PubMed

Yang, Xi; Yi, Honghong; Tang, Xiaolong; Zhao, Shunzheng; Yang, Zhongyu; Ma, Yueqiang; Feng, Tiecheng; Cui, Xiaoxu

2018-05-01

This work was undertaken to investigate the behaviors and kinetics of toluene adsorption and desorption on activated carbons with varying pore structure. Five kinds of activated carbon from different raw materials were selected. Adsorption isotherms and breakthrough curves for toluene were measured. Langmuir and Freundlich equations were fitted to the equilibrium data, and the Freundlich equation was more suitable for simulating toluene adsorption. The process consisted of monolayer, multilayer and partial active site adsorption types. The effect of the pore structure of the activated carbons on toluene adsorption capacity was investigated. The quasi-first-order model was more suitable for describing the process than the quasi-second-order model. The adsorption data was also modeled by the internal particle diffusion model and it was found that the adsorption process could be divided into three stages. In the external surface adsorption process, the rate depended on the specific surface area. During the particle diffusion stage, pore structure and volume were the main factors affecting adsorption rate. In the final equilibrium stage, the rate was determined by the ratio of meso- and macro-pores to total pore volume. The rate over the whole adsorption process was dominated by the toluene concentration. The desorption behavior of toluene on activated carbons was investigated, and the process was divided into heat and mass transfer parts corresponding to emission and diffusion mechanisms, respectively. Physical adsorption played the main role during the adsorption process. Copyright © 2017. Published by Elsevier B.V.

Pseudo second order kinetics and pseudo isotherms for malachite green onto activated carbon: comparison of linear and non-linear regression methods.

PubMed

Kumar, K Vasanth; Sivanesan, S

2006-08-25

Pseudo second order kinetic expressions of Ho, Sobkowsk and Czerwinski, Blanachard et al. and Ritchie were fitted to the experimental kinetic data of malachite green onto activated carbon by non-linear and linear method. Non-linear method was found to be a better way of obtaining the parameters involved in the second order rate kinetic expressions. Both linear and non-linear regression showed that the Sobkowsk and Czerwinski and Ritchie's pseudo second order model were the same. Non-linear regression analysis showed that both Blanachard et al. and Ho have similar ideas on the pseudo second order model but with different assumptions. The best fit of experimental data in Ho's pseudo second order expression by linear and non-linear regression method showed that Ho pseudo second order model was a better kinetic expression when compared to other pseudo second order kinetic expressions. The amount of dye adsorbed at equilibrium, q(e), was predicted from Ho pseudo second order expression and were fitted to the Langmuir, Freundlich and Redlich Peterson expressions by both linear and non-linear method to obtain the pseudo isotherms. The best fitting pseudo isotherm was found to be the Langmuir and Redlich Peterson isotherm. Redlich Peterson is a special case of Langmuir when the constant g equals unity.

Adsorption behavior and mechanism of chloramphenicols, sulfonamides, and non-antibiotic pharmaceuticals on multi-walled carbon nanotubes.

PubMed

Zhao, Heng; Liu, Xue; Cao, Zhen; Zhan, Yi; Shi, Xiaodong; Yang, Yi; Zhou, Junliang; Xu, Jiang

2016-06-05

The adsorption behavior of different emerging contaminants (3 chloramphenicols, 7 sulfonamides, and 3 non-antibiotic pharmaceuticals) on five types of multi-walled carbon nanotubes (MWCNTs), and the underlying factors were studied. Adsorption equilibriums were reached within 12h for all compounds, and well fitted by the Freundlich isotherm model. The adsorption affinity of pharmaceuticals was positively related to the specific surface area of MWCNTs. The solution pH was an important parameter of pharmaceutical adsorption on MWCNTs, due to its impacts on the chemical speciation of pharmaceuticals and the surface electrical property of MWCNTs. The adsorption of ionizable pharmaceuticals decreased in varying degrees with the increased ionic strength. MWCNT-10 was found to be the strongest adsorbent in this study, and the Freundlich constant (KF) values were 353-2814mmol(1-n)L(n)/kg, 571-618mmol(1-n)L(n)/kg, and 317-1522mmol(1-n)L(n)/kg for sulfonamides, chloramphenicols, and non-antibiotic pharmaceuticals, respectively. The different adsorption affinity of sulfonamides might contribute to the different hydrophobic of heterocyclic substituents, while chloramphenicols adsorption was affected by the charge distribution in aromatic rings via substituent effects. Copyright © 2016 Elsevier B.V. All rights reserved.

Removal of chromium (VI) using poly(methylacrylate) functionalized guar gum.

PubMed

Singh, Vandana; Kumari, Premlata; Pandey, Sadanand; Narayan, Tripti

2009-03-01

Using persulfate/ascorbic acid redox pair, poly(methylacrylate) was grafted on to guar gum and the conditions for the grafting were optimized. The copolymer sample having maximum %G was evaluated for the removal of Cr(VI) and the sorption conditions were optimized. The sorption was found pH dependent, pH 1.0 being the optimum value. Sorption data at pH 1.0 were modeled using both the Langmuir and Freundlich isotherms where the data fitted better to Freundlich isotherm. The equilibrium sorption capacity of 29.67mg/g was determined from the Langmuir isotherm. The sorption followed a pseudo-second-order kinetics with a rate constant 2.5x10(-4)gmg(-1) min(-1). The grafted product was also evaluated for Cr(VI) removal from local electroplating industrial waste water. The regeneration experiments revealed that the guar-graft-poly(methylacrylate) could be successfully reused for five cycles. In the present study conductivity measurements were used instead of conventional photometric method for determining Cr(VI) concentration in the equilibrium solutions and the results obtained have been compared with photometric method. Optimum Cr(VI) binding under highly acidic conditions indicated significant contribution of non electrostatic forces in the adsorption process.

Investigation of hexavalent chromium sorption in serpentine sediments

NASA Astrophysics Data System (ADS)

Mpouras, Thanasis; Chrysochoou, Maria; Dermatas, Dimitris

2017-02-01

In this study the removal of hexavalent chromium (Cr6 +) by serpentine sediments was investigated in order to delineate Cr6 + sorption behavior in aquifers with ultramafic geologic background. Batch experiments were conducted in order to determine the influence of several parameters on Cr6 + removal, including the pH of the sediment solution, mineralogy, sediment's particle size and Cr6 + initial concentration. The results showed that Cr6 + removal was due to both adsorption and reduction phenomena. Reduction was attributed to the presence of a magnetic fraction in the sediment, mostly related to magnetite, which contributed almost 50% of the total removal in the pH range 3-7. Adsorption behavior was dominated by the finer sediment fraction (d < 0.075 mm). The amount of Cr6 + adsorbed was constant in the pH range 3-7, while it decreased sharply in the range 7-8.5. Cr6 + adsorption was found to increase and decrease proportionally with increasing initial Cr6 + concentration of and particle size, respectively. The linear Langmuir and Freundlich adsorption isotherms were used to describe the experimental data, with Freundlich providing a better fit to determine distribution factors for transport modeling.

Equilibrium, kinetics and process design of acid yellow 132 adsorption onto red pine sawdust.

PubMed

Can, Mustafa

2015-01-01

Linear and non-linear regression procedures have been applied to the Langmuir, Freundlich, Tempkin, Dubinin-Radushkevich, and Redlich-Peterson isotherms for adsorption of acid yellow 132 (AY132) dye onto red pine (Pinus resinosa) sawdust. The effects of parameters such as particle size, stirring rate, contact time, dye concentration, adsorption dose, pH, and temperature were investigated, and interaction was characterized by Fourier transform infrared spectroscopy and field emission scanning electron microscope. The non-linear method of the Langmuir isotherm equation was found to be the best fitting model to the equilibrium data. The maximum monolayer adsorption capacity was found as 79.5 mg/g. The calculated thermodynamic results suggested that AY132 adsorption onto red pine sawdust was an exothermic, physisorption, and spontaneous process. Kinetics was analyzed by four different kinetic equations using non-linear regression analysis. The pseudo-second-order equation provides the best fit with experimental data.

Removal of fluoride from drinking water using aluminum hydroxide coated activated carbon prepared from bark of Morinda tinctoria

NASA Astrophysics Data System (ADS)

Amalraj, Augustine; Pius, Anitha

2017-10-01

The aim of this study is to design and develop a novel cost effective method for fluoride removal, applicable to rural areas of developing countries. Adsorption is widely considered as one of the appropriate technologies for water defluoridation. This study investigates the feasibility of using low-cost biomass based activated carbon from the bark of Morinda tinctoria coated with aluminum hydroxide (AHAC) for water defluoridation, at neutral pH range. Characterization of AHAC was done through IR, SEM with EDAX studies before and after fluoride treatment. The fluoride adsorption capacity of AHAC as a function of contact time, pH and initial fluoride concentration was investigated. The role of co-existing interfering ions also was studied. The isotherm and kinetic models were used to understand the nature of the fluoride adsorption onto AHAC. Freundlich isotherm and intra-particle diffusion were the best-fitting models for the adsorption of fluoride on AHAC. Fluoride adsorption kinetics well fitted with pseudo-second order model. The results showed excellent fluoride adsorption capacity was found to be 26.03 mg g-1 at neutral pH.

Adsorption of malachite green from aqueous solution by using novel chitosan ionic liquid beads.

PubMed

Naseeruteen, Faizah; Hamid, Nur Shahirah Abdul; Suah, Faiz Bukhari Mohd; Ngah, Wan Saime Wan; Mehamod, Faizatul Shimal

2018-02-01

Chitosan ionic liquid beads were prepared from chitosan and 1-butyl-3-methylimidazolium based ionic liquids to remove Malachite Green (MG) from aqueous solutions. Batch adsorption experiments were carried out as a function of initial pH, adsorbent dosage, agitation time and initial MG concentration. The optimum conditions were obtained at pH 4.0, 0.008g of adsorbent dosage and 20min of agitation time were utilized in the kinetic and isotherm studies. Three kinetic models were applied to analyze the kinetic data and pseudo-second order was found to be the best fitted model with R 2 >0.999. In order to determine the adsorption capacity, the sorption data were analyzed using the linear form of Langmuir, Freundlich and Temkin equations. The isotherm was best fitted by Langmuir isotherm model. The maximum adsorption capacity (q max ) obtained from Langmuir isotherm for two chitosan beads 1-butyl-3-methylimidazolium acetate A and 1-butyl-3-methylimidazolium B are 8.07mgg -1 and 0.24mgg -1 respectively. Copyright © 2017 Elsevier B.V. All rights reserved.

Biosorption of Cu(II) by powdered anaerobic granular sludge from aqueous medium.

PubMed

Zhou, Xu; Chen, Chuan; Wang, Aijie; Jiang, Guangming; Liu, Lihong; Xu, Xijun; Yuan, Ye; Lee, Duu-Jung; Ren, Nanqi

2013-01-01

Copper(II) biosorption processes by two pre-treated powdered anaerobic granular sludges (PAGS) (original sludges were methanogenic anaerobic granules and denitrifying sulfide removal (DSR) anaerobic granules) were investigated through batch tests. Factors affecting the biosorption process, such as pH, temperature and initial copper concentrations, were examined. Also, the physico-chemical characteristics of the anaerobic sludge were analyzed by Fourier transform infrared spectroscopy, scanning electron microscopy image, surface area and elemental analysis. A second-order kinetic model was applied to describe the biosorption process, and the model could fit the biosorption process. The Freundlich model was used for describing the adsorption equilibrium data and could fit the equilibrium data well. It was found that the methanogenic PAGS was more effective in Copper(II) biosorption process than the DSR PAGS, whose maximum biosorption capacity was 39.6% lower. The mechanisms of the biosorption capacities for different PAGS were discussed, and the conclusion suggested that the environment and biochemical reactions during the growth of biomass may have affected the structure of the PAGS. The methanogenic PAGS had larger specific surface area and more biosorption capacity than the DSR PAGS.

Biosorption of Cu(II) from aqueous solutions by mimosa tannin gel.

PubMed

Sengil, I Ayhan; Ozacar, Mahmut

2008-09-15

The biosorption of Cu(II) from aqueous solutions by mimosa tannin resin (MTR) was investigated as a function of particle size, initial pH, contact time and initial metal ion concentration. The aim of this study was to understand the mechanisms that govern copper removal and find a suitable equilibrium isotherm and kinetic model for the copper removal in a batch reactor. The experimental isotherm data were analysed using the Langmuir, Freundlich and Temkin equations. The equilibrium data fit well in the Langmiur isotherm. The experimental data were analysed using four sorption kinetic models -- the pseudo-first- and second-order equations, and the Elovich and the intraparticle diffusion equation -- to determine the best fit equation for the biosorption of copper ions onto mimosa tannin resin. Results show that the pseudo-second-order equation provides the best correlation for the biosorption process, whereas the Elovich equation also fits the experimental data well. Thermodynamic parameters such as the entropy change, enthalpy change and Gibb's free energy change were found out to be 153.0 J mol(-1)K(-1), 42.09 kJ mol(-1) and -2.47 kJ mol(-1), respectively.

Modelling equilibrium adsorption of single, binary, and ternary combinations of Cu, Pb, and Zn onto granular activated carbon.

PubMed

Loganathan, Paripurnanda; Shim, Wang Geun; Sounthararajah, Danious Pratheep; Kalaruban, Mahatheva; Nur, Tanjina; Vigneswaran, Saravanamuthu

2018-03-30

Elevated concentrations of heavy metals in water can be toxic to humans, animals, and aquatic organisms. A study was conducted on the removal of Cu, Pb, and Zn by a commonly used water treatment adsorbent, granular activated carbon (GAC), from three single, three binary (Cu-Pb, Cu-Zn, Pb-Zn), and one ternary (Cu-Pb-Zn) combination of metals. It also investigated seven mathematical models on their suitability to predict the metals adsorption capacities. Adsorption of Cu, Pb, and Zn increased with pH with an abrupt increase in adsorption at around pH 5.5, 4.5, and 6.0, respectively. At all pHs tested (2.5-7.0), the adsorption capacity followed the order Pb > Cu > Zn. The Langmuir and Sips models fitted better than the Freundlich model to the data in the single-metal system at pH 5. The Langmuir maximum adsorption capacities of Pb, Cu, and Zn (mmol/g) obtained from the model's fits were 0.142, 0.094, and 0.058, respectively. The adsorption capacities (mmol/g) for these metals at 0.01 mmol/L equilibrium liquid concentration were 0.130, 0.085, and 0.040, respectively. Ideal Adsorbed Solution (IAS)-Langmuir and IAS-Sips models fitted well to the binary and ternary metals adsorption data, whereas the Extended Langmuir and Extended Sips models' fits to the data were poor. The selectivity of adsorption followed the same order as the metals' capacities and affinities of adsorption in the single-metal systems.

Water defluoridation by aluminium oxide-manganese oxide composite material.

PubMed

Alemu, Sheta; Mulugeta, Eyobel; Zewge, Feleke; Chandravanshi, Bhagwan Singh

2014-08-01

In this study, aluminium oxide-manganese oxide (AOMO) composite material was synthesized, characterized, and tested for fluoride removal in batch experiments. AOMO was prepared from manganese(II) chloride and aluminium hydroxide. The surface area of AOMO was found to be 30.7m2/g and its specific density was determined as 2.78 g/cm3. Detailed investigation of the adsorbent by inductively coupled plasma-optical emission spectrometry, inductively coupled plasma-mass spectrometry, and ion chromatography (for sulphate only) showed that it is composed of Al, Mn, SO4, and Na as major components and Fe, Si, Ca, and Mg as minor components. Thermogravimetric analysis was used to study the thermal behaviour of AOMO. X-ray diffraction analysis showed that the adsorbent is poorly crystalline. The point of zero charge was determined as 9.54. Batch experiments (by varying the proportion of MnO, adsorbent dose, contact time, initial F concentration, and raw water pH) showed that fluoride removal efficiency ofAOMO varied significantly with percentage of MnO with an optimum value of about I11% of manganese oxide in the adsorbent. The optimum dose of the adsorbent was 4 g/L which corresponds to the equilibrium adsorption capacity of 4.8 mg F-/g. Both the removal efficiency and adsorption capacity showed an increasing trend with an increase in initial fluoride concentration of the water. The pH for optimum fluoride removal was found to be in the range between 5 and 7. The adsorption data were analysed using the Freundlich, Langmuir, and Dubinirn-Radushkevich models. The minimum adsorption capacity obtained from the non-linear Freundlich isotherm model was 4.94 mg F-/g and the maximum capacity from the Langmuir isotherm method was 19.2mg F-/g. The experimental data of fluoride adsorption on AOMO fitted well to the Freundlich isotherm model. Kinetic studies showed that the adsorption is well described by a non-linear pseudo-second-order reaction model with an average rate constant of 3.1 x 10(-2) g/min mg. It is concluded that AOMO is a highly promising adsorbent for the removal of excess fluoride from drinking water.

Adsorption and spectroscopic characterization of lactoferrin on hydroxyapatite nanocrystals.

PubMed

Iafisco, Michele; Di Foggia, Michele; Bonora, Sergio; Prat, Maria; Roveri, Norberto

2011-01-28

Lactoferrin (LF), a well-characterized protein of blood plasma and milk with antioxidant, cariostatic, anticarcinogenic and anti-inflammatory properties, has been adsorbed onto biomimetic hydroxyapatite (HA) nanocrystals at two different pH values (7.4 and 9.0). The interaction was herein investigated by spectroscopic, thermal and microscopic techniques. The positive electrostatic surface potential of LF at pH 7.4 allows a strong surface interaction with the slightly negative HA nanocrystals and avoids the protein-protein interaction, leading to the formation of a coating protein monolayer. In contrast, at pH 9.0 the surface potential of LF is a mix of negative and positive zones favouring the protein-protein interaction and reducing the interaction with HA nanocrystals; as a result a double layer of coating protein was formed. These experimental findings are supported by the good fittings of the adsorption isotherms by different theoretical models according to Langmuir, Freundlich and Langmuir-Freundlich models. The nanosized HA does not appreciably affect the conformation of the adsorbed protein. In fact, using FT-Raman and FT-IR, we found that after adsorption the protein was only slightly unfolded with a small fraction of the α-helix structure being converted into turn, while the β-sheet content remained almost unchanged. The bioactive surface of HA functionalized with LF could be utilized to improve the material performance towards the biological environment for biomedical applications.

Adsorption isotherm studies of Cu (II) and Co (II) in high concentration aqueous solutions on photocatalytically modified diatomaceous ceramic adsorbents

NASA Astrophysics Data System (ADS)

Ajenifuja, E.; Ajao, J. A.; Ajayi, E. O. B.

2017-11-01

Photocatalytically modified ceramic adsorbents were synthesized for the removal of high concentration Cu (II) and Co (II) ions from their aqueous solutions. The raw material, diatomaceous aluminosilicate mineral was modified using silver and anatase titanium oxide nanoparticles. Batch adsorption experiment was carried out on the targeted metal ions and the results were analyzed by the Langmuir and Freundlich equation at different concentrations (100-1000 mg/l) and the characteristic parameters for each adsorption isotherm were determined. As-received raw materials do not exhibit any sorption capacity for high concentration Cu2+ and Co2+ adsorbates. However, the adsorption isotherms for modified diatomaceous ceramic adsorbents could be fitted well by the Langmuir model for both Cu2+ and Co2+ with correlation coefficient ( R) of up to 0.99953. The highest and lowest monolayer coverage ( q max) were 121.803 and 31.289 mg/g for Cu2+ and Co2+, respectively. The separation factor ( R L) in the experiment was less than one (<1), indicating that the adsorption of metal ions on the Ag-TiO2-modified ceramic adsorbent is favorable. The highest adsorption capacity ( K f) and intensity ( n) constants obtained from Freundlich model are 38.832 (Cu2+ on ZEO-T) and 5.801 (Co2+ on STOX-Z).

Immobilization of 5-aminopyridine-2-tetrazole on cross-linked polystyrene for the preparation of a new adsorbent to remove heavy metal ions from aqueous solution.

PubMed

Zhang, Yu; Chen, Youning; Wang, Chaozhan; Wei, Yinmao

2014-07-15

Novel 5-aminopyridine-2-tetrazole-functionalized polystyrene resin (APTZ-PS) was prepared by anchoring 5-aminopyridine-2-carbonitrile onto chloromethylated polystyrene beads (CMPS) and subsequently using the cyano-tetrazole conversion reaction. The APTZ-PS resin was characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and specific surface area and pore size analyses. The adsorption experiments of the prepared resin for heavy metal ions were conducted by batch methods. The effects of the experimental conditions, such as pH, contact time and initial metal ion concentration on the adsorption properties of Cu(II), Pb(II) and Hg(II) were investigated. The results showed that the resin possessed perfect adsorption capacities for Cu(II), Pb(II) and Hg(II), and the selectivity was different from the commonly used iminodiacetic acid-chelating resin. The sorption kinetics of the three metal ions followed the pseudo-second-order equation. The adsorption isotherms for Cu(II) and Pb(II) could be better fitted by the Langmuir model than the Freundlich model, whereas the Freundlich model was the best for the Hg(II) ion. Even after five consecutive adsorption-desorption cycles, no obvious change in the adsorption capacity of the resin was found, which implied that the APTZ-PS resin was suitable for the efficient removal of heavy metal ions from aqueous solution. Copyright © 2014 Elsevier B.V. All rights reserved.

Adsorption mechanisms of removing heavy metals and dyes from aqueous solution using date pits solid adsorbent.

PubMed

Al-Ghouti, Mohammad A; Li, Juiki; Salamh, Yousef; Al-Laqtah, Nasir; Walker, Gavin; Ahmad, Mohammad N M

2010-04-15

A potential usefulness of raw date pits as an inexpensive solid adsorbent for methylene blue (MB), copper ion (Cu(2+)), and cadmium ion (Cd(2+)) has been demonstrated in this work. This work was conducted to provide fundamental information from the study of equilibrium adsorption isotherms and to investigate the adsorption mechanisms in the adsorption of MB, Cu(2+), and Cd(2+) onto raw date pits. The fit of two models, namely Langmuir and Freundlich models, to experimental data obtained from the adsorption isotherms was checked. The adsorption capacities of the raw date pits towards MB and both Cu(2+) and Cd(2+) ions obtained from Langmuir and Freundlich models were found to be 277.8, 35.9, and 39.5 mg g(-1), respectively. Surface functional groups on the raw date pits surface substantially influence the adsorption characteristics of MB, Cu(2+), and Cd(2+) onto the raw date pits. The Fourier transform infrared spectroscopy (FTIR) studies show clear differences in both absorbances and shapes of the bands and in their locations before and after solute adsorption. Two mechanisms were observed for MB adsorption, hydrogen bonding and electrostatic attraction, while other mechanisms were observed for Cu(2+) and Cd(2+). For Cu(2+), binding two cellulose/lignin units together is the predominant mechanism. For Cd(2+), the predominant mechanism is by binding itself using two hydroxyl groups in the cellulose/lignin unit. 2009 Elsevier B.V. All rights reserved.

Biosorption of Cd+2 by green plant biomass, Araucaria heterophylla: characterization, kinetic, isotherm and thermodynamic studies

NASA Astrophysics Data System (ADS)

Sarada, B.; Krishna Prasad, M.; Kishore Kumar, K.; Murthy, Ch V. R.

2017-11-01

The present study attempted to analyze the biosorption behavior of novel biosorbent, Araucaria heterophylla (green plant) biomass, to remove Cd+2 from solutions against various parameters, i.e., initial metal ion concentration, pH, temperature, sorbent dosage and biomass particle size. The maximum biosorption was found to be 90.02% at pH 5.5 and biosorption capacity ( q e) of Cd+2 is 9.2506 mg g-1. The Langmuir and Freundlich equilibrium adsorption isotherms were studied and it was observed that Freundlich model is the best fit than the Langmuir model with correlation co-efficient of 0.999. Kinetic studies indicated that the biosorption process of Cd+2 well followed the pseudo-second-order model with R 2 0.999. Thermodynamic studies observed that the process is exothermic (Δ H ° negative). Free energy change (Δ G °) with negative sign reflected the feasibility and spontaneous nature of the process. The chemical functional -OH groups, CH2 stretching vibrations, C=O carbonyl group of alcohol, C=O carbonyl group of amide, P=O stretching vibrations and -CH groups were involved in the biosorption process. The XRD pattern of the A. heterophylla was found to be mostly amorphous in nature. The SEM studies showed Cd+2 biosorption on selective grains of the biosorbent. It was concluded that A. heterophylla leaf powder can be used as an effective, low-cost, and environmentally friendly biosorbent for the removal of Cd+2 from aqueous solution.

Investigation of simultaneous biosorption of copper(II) and chromium(VI) on dried Chlorella vulgaris from binary metal mixtures: Application of multicomponent adsorption isotherms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aksu, Z.; Acikel, U.; Kutsal, T.

1999-02-01

Although the biosorption of single metal ions to various kinds of microorganisms has been extensively studied and the adsorption isotherms have been developed for only the single metal ion situation, very little attention has been given to the bioremoval and expression of adsorption isotherms of multimetal ions systems. In this study the simultaneous biosorption of copper(II) and chromium(VI) to Chlorella vulgaris from a binary metal mixture was studied and compared with the single metal ion situation in a batch stirred system. The effects of pH and single- and dual-metal ion concentrations on the equilibrium uptakes were investigated. In previous studiesmore » the optimum biosorption pH had been determined as 4.0 for copper(II) and as 2.0 for chromium(VI). Multimetal ion biosorption studies were performed at these two pH values. It was observed that the equilibrium uptakes of copper(II) or chromium(VI) ions were changed due to the biosorption pH and the presence of other metal ions. Adsorption isotherms were developed for both single- and dual-metal ions systems at these two pH values, and expressed by the mono- and multicomponent Langmuir and Freundlich adsorption models. Model parameters were estimated by nonlinear regression. It was seen that the adsorption equilibrium data fitted very well to the competitive Freundlich model in the concentration ranges studied.« less

Glyphosate sorption to soils of Argentina. Estimation of affinity coeficient by pedotransfer function

NASA Astrophysics Data System (ADS)

De Geronimo, Eduardo; Aparicio, Virginia; Costa, José Luis

2017-04-01

Argentine agricultural production is fundamentally based on a technological package that combines direct seeding and glyphosate with transgenic crops (soybean, maize and cotton). Therefore, glyphosate is the most employed herbicide in the country, where 180 to 200 million liters are applied every year. Glyphosate is strongly sorbed to soil by binding to clay minerals, layer silicates, metal oxides, non-crystalline materials or organic matter. Sorption of glyphosate is a reversible process that regulates the half-life and mobility of the herbicide and it is therefore related to the risk of contaminating courses of surface and groundwater. However, this behavior may vary depending on the characteristics of the soil on which it is applied. In addition, pH is a determining factor since it modifies the net charge in the molecule and, with it, the force of the electrostatic interaction between the glyphosate and the components of the soil. For a reliable risk assessment of groundwater contamination from pesticides precise predictions of sorption coefficients are needed. The aim of this work is to study the affinity of glyphosate to different soils of Argentina and create a model to estimate the glyphosate Freundlich sorption coefficient (Kf) from easily measurable soil properties. Adsorption of glyphosate was investigated on 12 different agricultural soils of Argentina using batch equilibration technique and fit to Freundlich sorption model. The correlation coefficients and the effects of soil characteristic factors on glyphosate adsorption parameter were analyzed through principal component and multiple lineal regression analysis. Results indicate that pH and clay contents were found to be the most significant soil factors which affect the glyphosate adsorption process. The Freundlich (Kf) pedotransfer function obtained by stepwise regression analysis was Kf = 735.2*Clay - 104.2*pH + 0.7*Polsen - 3.8*Alin. A 97.9% of the variation of glyphosate sorption coefficient could be attributed to the variation of the soil clay contents, pH, Polsen and Alin.

Sulfamethazine Sorption to Soil: Vegetative Management, pH, and Dissolved Organic Matter Effects.

PubMed

Chu, Bei; Goyne, Keith W; Anderson, Stephen H; Lin, Chung-Ho; Lerch, Robert N

2013-01-01

Elucidating veterinary antibiotic interactions with soil is important for assessing and mitigating possible environmental hazards. The objectives of this study were to investigate the effects of vegetative management, soil properties, and >1000 Da dissolved organic matter (DOM) on sulfamethazine (SMZ) behavior in soil. Sorption experiments were performed over a range of SMZ concentrations (2.5-50 μmol L) using samples from three soils (Armstrong, Huntington, and Menfro), each planted to one of three vegetation treatments: agroforestry buffers strips (ABS), grass buffer strips (GBS), and row crops (RC). Our results show that SMZ sorption isotherms are well fitted by the Freundlich isotherm model (log = 0.44-0.93; Freundlich nonlinearity parameter = 0.59-0.79). Further investigation of solid-to-solution distribution coefficients () demonstrated that vegetative management significantly ( < 0.05) influences SMZ sorption (ABS > GBS > RC). Multiple linear regression analyses indicated that organic carbon (OC) content, pH, and initial SMZ concentration were important properties controlling SMZ sorption. Study of the two most contrasting soils in our sample set revealed that increasing solution pH (pH 6.0-7.5) reduced SMZ sorption to the Armstrong GBS soil, but little pH effect was observed for the Huntington GBS soil containing 50% kaolinite in the clay fraction. The presence of DOM (150 mg L OC) had little significant effect on the Freundlich nonlinearity parameter; however, DOM slightly reduced SMZ values overall. Our results support the use of vegetative buffers to mitigate veterinary antibiotic loss from agroecosystems, provide guidance for properly managing vegetative buffer strips to increase SMZ sorption, and enhance understanding of SMZ sorption to soil. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Applications of Brazilian pine-fruit shell in natural and carbonized forms as adsorbents to removal of methylene blue from aqueous solutions--kinetic and equilibrium study.

PubMed

Royer, Betina; Cardoso, Natali F; Lima, Eder C; Vaghetti, Julio C P; Simon, Nathalia M; Calvete, Tatiana; Veses, Renato Cataluña

2009-05-30

The Brazilian pine-fruit shell (Araucaria angustifolia) is a food residue, which was used in natural and carbonized forms, as low-cost adsorbents for the removal of methylene blue (MB) from aqueous solutions. Chemical treatment of Brazilian pine-fruit shell (PW), with sulfuric acid produced a non-activated carbonaceous material (C-PW). Both PW and C-PW were tested as low-cost adsorbents for the removal of MB from aqueous effluents. It was observed that C-PW leaded to a remarkable increase in the specific surface area, average porous volume, and average porous diameter of the adsorbent when compared to PW. The effects of shaking time, adsorbent dosage and pH on adsorption capacity were studied. In basic pH region (pH 8.5) the adsorption of MB was favorable. The contact time required to obtain the equilibrium was 6 and 4h at 25 degrees C, using PW and C-PW as adsorbents, respectively. Based on error function values (F(error)) the kinetic data were better fitted to fractionary-order kinetic model when compared to pseudo-first order, pseudo-second order, and chemisorption kinetic models. The equilibrium data were fitted to Langmuir, Freundlich, Sips and Redlich-Peterson isotherm models. For MB dye the equilibrium data were better fitted to the Sips isotherm model using PW and C-PW as adsorbents.

Optimization of Biosorptive Removal of Dye from Aqueous System by Cone Shell of Calabrian Pine

PubMed Central

Deniz, Fatih

2014-01-01

The biosorption performance of raw cone shell of Calabrian pine for C.I. Basic Red 46 as a model azo dye from aqueous system was optimized using Taguchi experimental design methodology. L9 (33) orthogonal array was used to optimize the dye biosorption by the pine cone shell. The selected factors and their levels were biosorbent particle size, dye concentration, and contact time. The predicted dye biosorption capacity for the pine cone shell from Taguchi design was obtained as 71.770 mg g−1 under optimized biosorption conditions. This experimental design provided reasonable predictive performance of dye biosorption by the biosorbent (R 2: 0.9961). Langmuir model fitted better to the biosorption equilibrium data than Freundlich model. This displayed the monolayer coverage of dye molecules on the biosorbent surface. Dubinin-Radushkevich model and the standard Gibbs free energy change proposed physical biosorption for predominant mechanism. The logistic function presented the best fit to the data of biosorption kinetics. The kinetic parameters reflecting biosorption performance were also evaluated. The optimization study revealed that the pine cone shell can be an effective and economically feasible biosorbent for the removal of dye. PMID:25405213

Comparison of cadmium hydroxide nanowires and silver nanoparticles loaded on activated carbon as new adsorbents for efficient removal of Sunset yellow: Kinetics and equilibrium study.

PubMed

Ghaedi, Mehrorang

2012-08-01

Adsorption of Sunset yellow (SY) onto cadmium hydroxide nanowires loaded on activated carbon (Cd(OH)(2)-NW-AC) and silver nanoparticles loaded on activated carbon (Ag-NP-AC) was investigated. The effects of pH, contact time, amount of adsorbents, initial dye concentration, agitation speed and temperature on Sunset yellow removal on both adsorbents were studied. Following the optimization of variables, the experimental data were fitted to different conventional isotherm models like Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich (D-R) based on linear regression coefficient R(2) the Langmuir isotherm was found to be the best fitting isotherm model and the maximum monolayer adsorption capacities calculated based on this model for Cd(OH)(2)-NW-AC and Ag-NP-AC were found to be 76.9 and 37.03mg g(-1) at room temperatures, respectively. The experimental fitting of time dependency of adsorption of SY onto both adsorbent shows the applicability of second order kinetic model for interpretation of kinetic data. The pseudo-second order model best fits the adsorption kinetics. Thermodynamic parameters such as enthalpy, entropy, activation energy, sticking probability, and Gibb's free energy changes were also calculated. It was found that the sorption of SY over (Cd(OH)(2)-NW-AC) and (Ag-NP-AC) was spontaneous and endothermic in nature. Efficiency of the adsorbent was also investigated using real effluents and more than 95% SY removal for both adsorbents was observed. Copyright © 2012 Elsevier B.V. All rights reserved.

Selenium uptake and assessment of the biochemical changes in Arthrospira (Spirulina) platensis biomass during the synthesis of selenium nanoparticles.

PubMed

Zinicovscaia, I; Chiriac, T; Cepoi, L; Rudi, L; Culicov, O; Frontasyeva, M; Rudic, V

2017-01-01

The process of selenium uptake by biomass of the cyanobacterium Arthrospira (Spirulina) platensis was investigated by neutron activation analysis at different selenium concentrations in solution and at different contact times. Experimental data showed good fit with the Freundlich adsorption isotherm model, with a regression coefficient value of 0.99. In terms of absorption dependence on time, the maximal selenium content was adsorbed in the first 5 min of interaction without significant further changes. It was also found that A. platensis biomass forms spherical selenium nanoparticles. Biochemical analysis was used to assess the changes in the main components of spirulina biomass (proteins, lipids, carbohydrates, and phycobilin) during nanoparticle formation.

Treatment of oily waters using vermiculite.

PubMed

Mysore, Deepa; Viraraghavan, Thiruvenkatachari; Jin, Yee-Chung

2005-07-01

The main objective of this study was to examine the removal of oil from water by expanded and hydrophobized vermiculite. A pH of 9 showed a higher removal efficiency of oil by vermiculite. Oil removal efficiencies at pH 9 were found to be 79%, 93%, 90%, 57% for standard mineral oil (SMO), Canola oil (CO), Kutwell oil (KUT45), refinery effluent (RE), respectively, in the case of expanded vermiculite, and 56%, 58%, 47%, 43% for SMO, CO, KUT45 and RE, respectively, for hydrophobized vermiculite. Kinetic data satisfied both the Lagergren and Ho models. Equilibrium studies showed that the Langmuir isotherm was the best-fit isotherm for oil removal by both expanded and hydrophobized vermiculite. The data showed a higher adsorptive capacity by the expanded vermiculite compared to the hydrophobized vermiculite. Desorption studies showed that the expanded vermiculite did not desorb oil to the same extent compared to hydrophobized vermiculite. The Freundlich isotherm was the best-fit model for desorption. Expanded vermiculite showed better retention than hydrophobic vermiculite. The results showed that the expanded vermiculite had a greater affinity for oil than hydrophobized vermiculite.

Removal of sulfur compounds from petroleum refinery wastewater through adsorption on modified activated carbon.

PubMed

Ben Hariz, Ichrak; Al Ayni, Foued; Monser, Lotfi

2014-01-01

The adsorption of sulfur compounds from petroleum refinery wastewater on a chemically modified activated carbon (MAC) was investigated. The modification technique (nitric acid, hydrogen peroxide and thermal modification) enhanced the removal capacity of carbon and therefore decreases cost-effective removal of sulfide from refinery wastewater. Adsorption equilibrium and kinetics data were determined for sulfur removal from real refinery wastewater. The data were evaluated according to several adsorption isotherm and kinetics models. The Freundlich isotherm fitted well with the equilibrium data of sulfur on different adsorbents, whereas the kinetics data were best fitted by the pseudo-second-order model. Insights of sulfide removal mechanisms indicated that the sorption was controlled through the intraparticle diffusion mechanism with a significant contribution of film diffusion. The MAC adsorbent was found to have an effective removal capacity of approximately 2.5 times that of non-modified carbon. Using different MAC, sulfides were eliminated with a removal capacity of 52 mg g(-1). Therefore, MAC can be utilized as an effective and less expensive adsorbent for the reduction of sulfur in refinery wastewater.

Removal of glyphosate herbicide from water using biopolymer membranes.

PubMed

Carneiro, Rafael T A; Taketa, Thiago B; Gomes Neto, Reginaldo J; Oliveira, Jhones L; Campos, Estefânia V R; de Moraes, Mariana A; da Silva, Camila M G; Beppu, Marisa M; Fraceto, Leonardo F

2015-03-15

Enormous amounts of pesticides are manufactured and used worldwide, some of which reach soils and aquatic systems. Glyphosate is a non-selective herbicide that is effective against all types of weeds and has been used for many years. It can therefore be found as a contaminant in water, and procedures are required for its removal. This work investigates the use of biopolymeric membranes prepared with chitosan (CS), alginate (AG), and a chitosan/alginate combination (CS/AG) for the adsorption of glyphosate present in water samples. The adsorption of glyphosate by the different membranes was investigated using the pseudo-first order and pseudo-second order kinetic models, as well as the Langmuir and Freundlich isotherm models. The membranes were characterized regarding membrane solubility, swelling, mechanical, chemical and morphological properties. The results of kinetics experiments showed that adsorption equilibrium was reached within 4 h and that the CS membrane presented the best adsorption (10.88 mg of glyphosate/g of membrane), followed by the CS/AG bilayer (8.70 mg of glyphosate/g of membrane). The AG membrane did not show any adsorption capacity for this herbicide. The pseudo-second order model provided good fits to the glyphosate adsorption data on CS and CS/AG membranes, with high correlation coefficient values. Glyphosate adsorption by the membranes could be fitted by the Freundlich isotherm model. There was a high affinity between glyphosate and the CS membrane and moderate affinity in the case of the CS/AG membrane. Physico-chemical characterization of the membranes showed low values of solubility in water, indicating that the membranes are stable and not soluble in water. The SEM and AFM analysis showed evidence of the presence of glyphosate on CS membranes and on chitosan face on CS/AG membranes. The results showed that the glyphosate herbicide can be adsorbed by chitosan membranes and the proposed membrane-based methodology was successfully used to treat a water sample contaminated with glyphosate. Biopolymer membranes therefore potentially offer a versatile method to eliminate agricultural chemicals from water supplies. Copyright © 2015 Elsevier Ltd. All rights reserved.

Aminocyclopyrachlor sorption-desorption and leaching from three Brazilian soils.

PubMed

Francisco, Jeane G; Mendes, Kassio F; Pimpinato, Rodrigo F; Tornisielo, Valdemar L; Guimarães, Ana C D

2017-07-03

This study aimed to evaluate the sorption-desorption and leaching of aminocyclopyrachlor from three Brazilian soils. The sorption-desorption of 14 C-aminocyclopyrachlor was evaluated using the batch method and leaching was assessed in glass columns. The Freundlich model showed an adequate fit for the sorption-desorption of aminocyclopyrachlor. The Freundlich sorption coefficient [K f (sorption) ] ranged from 0.37 to 1.34 µmol (1-1/n) L 1/n kg -1 and showed a significant positive correlation with the clay content of the soil, while the K f (desorption) ranged from 3.62 to 5.36 µmol (1-1/n) L 1/n kg -1 . The K f (desorption) values were higher than their respective K f (sorption) , indicating that aminocyclopyrachlor sorption is reversible, and the fate of this herbicide in the environment can be affected by leaching. Aminocyclopyrachlor was detected at all depths (0-30 cm) in all the studied soils, where leaching was influenced by soil texture. The total herbicide leaching from the sandy clay and clay soils was <0.06%, whereas, ∼3% leached from the loamy sand soil. The results suggest that aminocyclopyrachlor has a high potential of leaching, based on its low sorption and high desorption capacities. Therefore, this herbicide can easily contaminate underground water resources.

Adsorption of Cd, Cu and Zn from aqueous solutions onto ferronickel slag under different potentially toxic metal combination.

PubMed

Park, Jong-Hwan; Kim, Seong-Heon; Kang, Se-Won; Kang, Byung-Hwa; Cho, Ju-Sik; Heo, Jong-Soo; Delaune, Ronald D; Ok, Yong Sik; Seo, Dong-Cheol

2016-01-01

Adsorption characteristics of potentially toxic metals in single- and multi-metal forms onto ferronickel slag were evaluated. Competitive sorption of metals by ferronickel slag has never been reported previously. The maximum adsorption capacities of toxic metals on ferronickel were in the order of Cd (10.2 mg g(-1)) > Cu (8.4 mg g(-1)) > Zn (4.4 mg g(-1)) in the single-metal adsorption isotherm and Cu (6.1 mg g(-1)) > Cd (2.3 mg g(-1)) > Zn (0.3 mg g(-1)) in the multi-metal adsorption isotherm. In comparison with single-metal adsorption isotherm, the reduction rates of maximum toxic metal adsorption capacity in the multi-metal adsorption isotherm were in the following order of Zn (93%) > Cd (78%) > Cu (27%). The Freundlich isotherm provides a slightly better fit than the Langmuir isotherm equation using ferronickel slag for potentially toxic metal adsorption. Multi-metal adsorption behaviors differed from single-metal adsorption due to competition, based on data obtained from Freundlich and Langmuir adsorption models and three-dimensional simulation. Especially, Cd and Zn were easily exchanged and substituted by Cu during multi-metal adsorption. Further competitive adsorption studies are necessary in order to accurately estimate adsorption capacity of ferronickel slag for potentially toxic metals in natural environments.

Detailed sorption characteristics of the anti-diabetic drug metformin and its transformation product guanylurea in agricultural soils.

PubMed

Briones, Rowena M; Sarmah, Ajit K

2018-07-15

Detection of metformin, an antidiabetic drug and its transformation product guanylurea in various environmental matrices such as surface water and groundwater, coupled with their effects on aquatic organisms warrant an understanding of the compounds fate and behaviour in the environment. Batch studies were conducted with the aim of evaluating the sorption of these two emerging contaminants in six New Zealand agricultural soils of contrasting physico-chemical properties. Kinetic studies revealed that metformin and guanylurea sorption in Te Kowhai soil was very rapid initially achieving 90% sorption within the first 4 and 13h, respectively. Fit of several isotherm models to the measured batch sorption data showed that the hybrid models Langmuir-Freundlich and Redlich-Peterson best described the isotherms. Freundlich isotherm showed higher linearity for guanylurea (n F =0.58-0.93) in all soils compared to metformin (n F =0.25-0.71). A linear isotherm was fitted at environmentally relevant low concentrations (< 3mg/L) of target compounds and calculated values of sorption distribution coefficient (K d ) were in the range of 8.97 to 53.49L/kg for metformin and between 10.6 and 37.51L/kg for guanylurea. Sorption of both metformin and guanylurea was dependent on the soil characteristics, however, no generalisation could be made as to which had higher affinity to soils studied. Pearson's correlation and multiple regression analyses indicate that Si/Al (p=0.042) and clay (p=0.015) significantly influenced metformin K d values, whereas the soil's cation exchange capacity (p=0.024) is the single most significant factor determining guanylurea sorption in soils. It is likely that the type of minerals present in soils and its ion-exchange capacity could play an important role in metformin and guanylurea sorption, respectively. Copyright © 2018. Published by Elsevier B.V.

Optimizing the Removal of Rhodamine B in Aqueous Solutions by Reduced Graphene Oxide-Supported Nanoscale Zerovalent Iron (nZVI/rGO) Using an Artificial Neural Network-Genetic Algorithm (ANN-GA)

PubMed Central

Shi, Xuedan; Ruan, Wenqian; Hu, Jiwei; Fan, Mingyi; Cao, Rensheng; Wei, Xionghui

2017-01-01

Rhodamine B (Rh B) is a toxic dye that is harmful to the environment, humans, and animals, and thus the discharge of Rh B wastewater has become a critical concern. In the present study, reduced graphene oxide-supported nanoscale zero-valent iron (nZVI/rGO) was used to treat Rh B aqueous solutions. The nZVI/rGO composites were synthesized with the chemical deposition method and were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, N2-sorption, and X-ray photoelectron spectroscopy (XPS) analysis. The effects of several important parameters (initial pH, initial concentration, temperature, and contact time) on the removal of Rh B by nZVI/rGO were optimized by response surface methodology (RSM) and artificial neural network hybridized with genetic algorithm (ANN-GA). The results suggest that the ANN-GA model was more accurate than the RSM model. The predicted optimum value of Rh B removal efficiency (90.0%) was determined using the ANN-GA model, which was compatible with the experimental value (86.4%). Moreover, the Langmuir, Freundlich, and Temkin isotherm equations were applied to fit the adsorption equilibrium data, and the Freundlich isotherm was the most suitable model for describing the process for sorption of Rh B onto the nZVI/rGO composites. The maximum adsorption capacity based on the Langmuir isotherm was 87.72 mg/g. The removal process of Rh B could be completed within 20 min, which was well described by the pseudo-second order kinetic model. PMID:28587196

Optimizing the Removal of Rhodamine B in Aqueous Solutions by Reduced Graphene Oxide-Supported Nanoscale Zerovalent Iron (nZVI/rGO) Using an Artificial Neural Network-Genetic Algorithm (ANN-GA).

PubMed

Shi, Xuedan; Ruan, Wenqian; Hu, Jiwei; Fan, Mingyi; Cao, Rensheng; Wei, Xionghui

2017-06-03

Rhodamine B (Rh B) is a toxic dye that is harmful to the environment, humans, and animals, and thus the discharge of Rh B wastewater has become a critical concern. In the present study, reduced graphene oxide-supported nanoscale zero-valent iron (nZVI/rGO) was used to treat Rh B aqueous solutions. The nZVI/rGO composites were synthesized with the chemical deposition method and were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, N₂-sorption, and X-ray photoelectron spectroscopy (XPS) analysis. The effects of several important parameters (initial pH, initial concentration, temperature, and contact time) on the removal of Rh B by nZVI/rGO were optimized by response surface methodology (RSM) and artificial neural network hybridized with genetic algorithm (ANN-GA). The results suggest that the ANN-GA model was more accurate than the RSM model. The predicted optimum value of Rh B removal efficiency (90.0%) was determined using the ANN-GA model, which was compatible with the experimental value (86.4%). Moreover, the Langmuir, Freundlich, and Temkin isotherm equations were applied to fit the adsorption equilibrium data, and the Freundlich isotherm was the most suitable model for describing the process for sorption of Rh B onto the nZVI/rGO composites. The maximum adsorption capacity based on the Langmuir isotherm was 87.72 mg/g. The removal process of Rh B could be completed within 20 min, which was well described by the pseudo-second order kinetic model.

Application of Glycyrrhiza glabra Root as a Novel Adsorbent in the Removal of Toluene Vapors: Equilibrium, Kinetic, and Thermodynamic Study

PubMed Central

Mohammadi-Moghadam, Fazel; Amin, Mohammad Mehdi; Khiadani (Hajian), Mehdi; Momenbeik, Fariborz; Nourmoradi, Heshmatollah; Hatamipour, Mohammad Sadegh

2013-01-01

The aim of this paper is to investigate the removal of toluene from gaseous solution through Glycyrrhiza glabra root (GGR) as a waste material. The batch adsorption experiments were conducted at various conditions including contact time, adsorbate concentration, humidity, and temperature. The adsorption capacity was increased by raising the sorbent humidity up to 50 percent. The adsorption of toluene was also increased over contact time by 12 h when the sorbent was saturated. The pseudo-second-order kinetic model and Freundlich model fitted the adsorption data better than other kinetic and isotherm models, respectively. The Dubinin-Radushkevich (D-R) isotherm also showed that the sorption by GGR was physical in nature. The results of the thermodynamic analysis illustrated that the adsorption process is exothermic. GGR as a novel adsorbent has not previously been used for the adsorption of pollutants. PMID:23554821

Rapid removal of aniline from contaminated water by a novel polymeric adsorbent.

PubMed

Huang, Yunhong; Xu, Yang; He, Qinghua; Cao, Yusheng; Du, Bibai

2014-01-01

Dummy molecularly imprinted polymers (DMIPs) for aniline were synthesized by a thermal polymerization method using acrylamide as a functional monomer, ethylene dimethacrylate as a crosslinker, 2,2-azobisisobutyronitrile as a free radical initiator, acetonitrile as a porogenic solvent, and analogues of aniline, namely sulfadiazine, as the template. The DMIPs that were obtained showed a high affinity to aniline compared to non-imprinted polymers. It was proven that the DMIPs obtained using sulfadiazine as the template were much better than the molecularly imprinted polymers using aniline as the template. The results indicated that the Freundlich model was fit for the adsorption model of DMIP for aniline and the adsorption model of the DMIP for aniline was multilayer adsorption. Furthermore, the results showed that the DMIP synthesized by bulk polymerization could be used as a novel adsorbent for removal of aniline from contaminated water.

Adsorption/electrosorption of catechol and resorcinol onto high area activated carbon cloth.

PubMed

Bayram, Edip; Hoda, Numan; Ayranci, Erol

2009-09-15

Removal of catechol and resorcinol from aqueous solutions by adsorption and electrosorption onto high area activated carbon cloth (ACC) was investigated. Kinetics of both adsorption and electrosorption were followed by in-situ UV-spectroscopic method and the data were treated according to pseudo-first-order, pseudo-second-order and intraparticle diffusion models. It was found that the adsorption and electrosorption of these compounds onto ACC follows pseudo-second-order model. pH changes during adsorption and electrosorption were followed and discussed with regard to the interaction between ACC and adsorbate molecules, utilizing the pH(pzc) value of ACC. An electrodesorption experiment was conducted to explore the possibility of regeneration of ACC. Adsorption isotherms were derived at 25 degrees C on the basis of batch analysis. The fits of experimental isotherm data to the well-known Freundlich, Langmuir and Tempkin models were examined.

Adsorption of aluminum and lead from wastewater by chitosan-tannic acid modified biopolymers: Isotherms, kinetics, thermodynamics and process mechanism.

PubMed

Badawi, M A; Negm, N A; Abou Kana, M T H; Hefni, H H; Abdel Moneem, M M

2017-06-01

Chitosan was reacted by tannic acid to obtain three modified chitosan biopolymer. Their chemical structures were characterized by FTIR and elemental analysis. The prepared biopolymers were used to adsorb Al(III) and Pb(II) metal ions from industrial wastewater. The factors affecting the adsorption process were biosorbent amount, initial concentration of metal ion and pH of the medium. The adsorption efficiency increased considerably with the increase of the biosorbent amount and pH of the medium. The adsorption process of biosorbent on different metal ions was fitted by Freundlich adsorption model. The adsorption kinetics was followed Pseudo-second-order kinetic model. The adsorption process occurred according to diffusion mechanism which was confirmed by the interparticle diffusion model. The modified biopolymers were efficient biosorbents for removal of Pb(II) and Al(III) metal ions from the medium. Copyright © 2017 Elsevier B.V. All rights reserved.

On the biosorption, by brown seaweed, Lobophora variegata, of Ni(II) from aqueous solutions: equilibrium and thermodynamic studies.

PubMed

Basha, Shaik; Jaiswar, Santlal; Jha, Bhavanath

2010-09-01

The biosorption equilibrium isotherms of Ni(II) onto marine brown algae Lobophora variegata, which was chemically-modified by CaCl(2) were studied and modeled. To predict the biosorption isotherms and to determine the characteristic parameters for process design, twenty-three one-, two-, three-, four- and five-parameter isotherm models were applied to experimental data. The interaction among biosorbed molecules is attractive and biosorption is carried out on energetically different sites and is an endothermic process. The five-parameter Fritz-Schluender model gives the most accurate fit with high regression coefficient, R (2) (0.9911-0.9975) and F-ratio (118.03-179.96), and low standard error, SE (0.0902-0.0.1556) and the residual or sum of square error, SSE (0.0012-0.1789) values to all experimental data in comparison to other models. The biosorption isotherm models fitted the experimental data in the order: Fritz-Schluender (five-parameter) > Freundlich (two-parameter) > Langmuir (two-parameter) > Khan (three-parameter) > Fritz-Schluender (four-parameter). The thermodynamic parameters such as DeltaG (0), DeltaH (0) and DeltaS (0) have been determined, which indicates the sorption of Ni(II) onto L. variegata was spontaneous and endothermic in nature.

Vanadium sorption by mineral soils: Development of a predictive model.

PubMed

Larsson, Maja A; Hadialhejazi, Golshid; Gustafsson, Jon Petter

2017-02-01

The toxicity of vanadium in soils depends on its sorption to soil components. Here we studied the vanadate(V) sorption properties of 26 mineral soils. The data were used to optimise parameters for a Freundlich equation with a pH term. Vanadium K-edge XANES spectroscopy for three selected soils confirmed that the added vanadate(V) had accumulated mostly as adsorbed vanadate(V) on Fe and Al hydrous oxides, with only minor contributions from organically complexed vanadium(IV). Data on pH-dependent V solubility for seven soils showed that on average 0.36 H + accompanied each V during adsorption and desorption. The resulting model provided reasonable fits to the V sorption data, with r 2  > 0.99 for 20 of 26 soils. The observed K dS value, i.e. the ratio of total to dissolved V, was strongly dependent on V addition and soil; it varied between 3 and 4 orders of magnitude. The model was used to calculate the Freundlich sorption strength (FSS), i.e. the amount of V sorbed at [V] = 2.5 mg L -1 , in the concentration range of observed plant toxicities. A close relationship between FSS and oxalate-extractable Fe and Al was found (r 2  = 0.85) when one acidic soil was removed from the regression. The FSS varied between 27 and 8718 mg V kg -1 , showing that the current environmental guidelines can be both under- and overprotective for vanadium. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sorption equilibrium of mercury onto ground-up tree fern.

PubMed

Ho, Yuh-Shan; Wang, Chung-Chi

2008-08-15

The sorption behavior of mercury at different temperatures onto ground-up tree fern was investigated. The experimental results were fitted to two two-parameter isotherms, the Freundlich and Langmuir isotherms, as well as to two three-parameter isotherms, the Redlich-Peterson and Sips isotherms to obtain the characteristic parameters of each model. A comparison of best-fitting was performed using the coefficient of determination and Chi-square test. Both the Langmuir and Redlich-Peterson isotherms were found to well represent the measured sorption data. According to the evaluation using the Langmuir equation, the saturated monolayer sorption capacity of mercury ions onto ground-up tree fern was 26.5 mg/g at 298 K. It was noted that an increase in temperature resulted in a higher mercury ion loading per unit weight of the tree fern. In addition, various thermodynamic parameters, such as DeltaG degrees, DeltaH degrees, and DeltaS degrees, were calculated and compared with the sorption of mercury by other sorbents.

Razor clam (Ensis directus) shell as a low-cost adsorbent for the removal of Congo red and Rhodamine B dyes from aqueous solution

NASA Astrophysics Data System (ADS)

Areibat, Lila Elamari Mohamed; Kamari, Azlan

2017-05-01

Wastewater originating from industrial effluents contains many types of pollutants including dyes. Anionic and cationic dyes are very toxic and they can cause several problems to aquatic system. In present study, razor clam shell was used as a potential adsorbent to remove two classes of dyes, namely anionic (Congo red, CR) and cationic (Rhodamine B, RB) dyes from aqueous solution. Batch adsorption experiments were performed to study the effects of three experimental parameters, namely solution pH, adsorbent dosage and initial dye concentration, on adsorption capacity of CR and RB onto razor clam shell. Results indicated that pH 2.0 was optimum pH for adsorbent to adsorb both CR and RB. At an initial concentration of 20 mg/L, the removal percentages of CR and RB were 97% and 38%, respectively. The Freundlich and Langmuir isotherm models were used to describe adsorption behaviour of CR and RB, as well as the relationship between adsorbent and adsorbate. The adsorption equilibrium data were well fitted to Freundlich isotherm model. The separation factor (RL) constants suggest that both CR and RB were favourably adsorbed by razor clam shell. Razor clam shell was characterised by using two techniques, namely Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectrometry (FTIR). Overall, this study suggests that razor clam shell has great potential to be an alternative to expensive adsorbents.

Cerium Binding Activity of Pectins Isolated from the Seagrasses Zostera marina and Phyllospadix iwatensis

PubMed Central

Khotimchenko, Yuri; Khozhaenko, Elena; Kovalev, Valeri; Khotimchenko, Maxim

2012-01-01

Cerium binding activity of three different water soluble pectin compounds of different origin was studied in a batch sorption system. The Langmuir, Freundlich and BET sorption models were adopted to describe the binding reactions between metal ions and pectin molecules. The Langmuir model provided the best fit. Within the pH range from 4.0 to 6.0, the largest amount of the cerium ions was bound by pectin isolated from the seagrass Phylospadix iwatensis in comparison to pectin extracted from the seagrass Zostera marina and pectin obtained from citrus peel (commercial grade). The Langmuir constants were also highest for the pectin samples isolated from the seagrass P. iwatensis. The results obtained from this study suggest that pectin is a prospective source for the development of radioisotope-removing pharmaceuticals. PMID:22690146

Adsorptive removal of phthalate ester (Di-ethyl phthalate) from aqueous phase by activated carbon: a kinetic study.

PubMed

Venkata Mohan, S; Shailaja, S; Rama Krishna, M; Sarma, P N

2007-07-19

Adsorptive studies were carried out on Di-ethyl phthalate (DEP) removal from aqueous phase onto activated carbon. Batch sorption studies were performed and the results revealed that activated carbon demonstrated ability to adsorb DEP. Influence of varying experimental conditions such as DEP concentration, pH of aqueous solution, and dosage of adsorbent were investigated on the adsorption process. Sorption interaction of DEP onto activated carbon obeyed the pseudo second order rate equation. Experimental data showed good fit with both the Langmuir and Freundlich adsorption isotherm models. DEP sorption was found to be dependent on the aqueous phase pH and the uptake was observed to be greater at acidic pH.

Comparison of linear and non-linear method in estimating the sorption isotherm parameters for safranin onto activated carbon.

PubMed

Kumar, K Vasanth; Sivanesan, S

2005-08-31

Comparison analysis of linear least square method and non-linear method for estimating the isotherm parameters was made using the experimental equilibrium data of safranin onto activated carbon at two different solution temperatures 305 and 313 K. Equilibrium data were fitted to Freundlich, Langmuir and Redlich-Peterson isotherm equations. All the three isotherm equations showed a better fit to the experimental equilibrium data. The results showed that non-linear method could be a better way to obtain the isotherm parameters. Redlich-Peterson isotherm is a special case of Langmuir isotherm when the Redlich-Peterson isotherm constant g was unity.

Comparative analysis of linear and non-linear method of estimating the sorption isotherm parameters for malachite green onto activated carbon.

PubMed

Kumar, K Vasanth

2006-08-21

The experimental equilibrium data of malachite green onto activated carbon were fitted to the Freundlich, Langmuir and Redlich-Peterson isotherms by linear and non-linear method. A comparison between linear and non-linear of estimating the isotherm parameters was discussed. The four different linearized form of Langmuir isotherm were also discussed. The results confirmed that the non-linear method as a better way to obtain isotherm parameters. The best fitting isotherm was Langmuir and Redlich-Peterson isotherm. Redlich-Peterson is a special case of Langmuir when the Redlich-Peterson isotherm constant g was unity.

Cadmium hydroxide nanowire loaded on activated carbon as efficient adsorbent for removal of Bromocresol Green

NASA Astrophysics Data System (ADS)

Ghaedi, Mehrorang; Khajesharifi, Habibollah; Hemmati Yadkuri, Amin; Roosta, Mostafa; Sahraei, Reza; Daneshfar, Ali

2012-02-01

In the present research, cadmium hydroxide nanowire loaded on activated carbon (Cd(OH) 2-NW-AC) was synthesized and characterized. This new adsorbent was applied for the removal of Bromocresol Green (BCG) molecules from aqueous solutions. The influence of effective variables such as solution pH, contact time, initial BCG concentration, amount of Cd(OH) 2-NW-AC and temperature on the adsorption efficiency of BCG in batch system was examined. During all experiments BCG contents were determined by UV-Vis spectrophotometer. Fitting the experimental data to different kinetic models including pseudo-first-order, pseudo-second-order, Elovich and intra-particle diffusion kinetic models show the suitability of the pseudo-second-order kinetic model to interpret in the experimental data. Equilibrium isotherm studies were examined by application of different conventional models such as Langmuir, Freundlich and Tempkin models to explain the experimental data. Based on considering R2 value as criterion the adsorption data well fitted to Langmuir model with maximum adsorption capacity of 108.7 mg g -1. Thermodynamic parameters (Gibb's free energy, entropy and enthalpy) of adsorption were calculated according to general procedure to take some information about the on-going adsorption process. The high negative value of Gibb's free energy and positive value of enthalpy show the feasibility and endothermic nature of adsorption process.

Cadmium hydroxide nanowire loaded on activated carbon as efficient adsorbent for removal of Bromocresol Green.

PubMed

Ghaedi, Mehrorang; Khajesharifi, Habibollah; Hemmati Yadkuri, Amin; Roosta, Mostafa; Sahraei, Reza; Daneshfar, Ali

2012-02-01

In the present research, cadmium hydroxide nanowire loaded on activated carbon (Cd(OH)(2)-NW-AC) was synthesized and characterized. This new adsorbent was applied for the removal of Bromocresol Green (BCG) molecules from aqueous solutions. The influence of effective variables such as solution pH, contact time, initial BCG concentration, amount of Cd(OH)(2)-NW-AC and temperature on the adsorption efficiency of BCG in batch system was examined. During all experiments BCG contents were determined by UV-Vis spectrophotometer. Fitting the experimental data to different kinetic models including pseudo-first-order, pseudo-second-order, Elovich and intra-particle diffusion kinetic models show the suitability of the pseudo-second-order kinetic model to interpret in the experimental data. Equilibrium isotherm studies were examined by application of different conventional models such as Langmuir, Freundlich and Tempkin models to explain the experimental data. Based on considering R(2) value as criterion the adsorption data well fitted to Langmuir model with maximum adsorption capacity of 108.7 mg g(-1). Thermodynamic parameters (Gibb's free energy, entropy and enthalpy) of adsorption were calculated according to general procedure to take some information about the on-going adsorption process. The high negative value of Gibb's free energy and positive value of enthalpy show the feasibility and endothermic nature of adsorption process. Copyright © 2011 Elsevier B.V. All rights reserved.

Single-solute and bisolute sorption of phenol and trichloroethylene from aqueous solution onto modified montmorillonite and application of sorption models.

PubMed

Wu, C D; Wang, L; Hu, C X; He, M H

2013-01-01

The single-solute and bisolute sorption behaviour of phenol and trichloroethylene, two organic compounds with different structures, onto cetyltrimethylammonium bromide (CTAB)-montmorillonite was studied. The monolayer Langmuir model (MLM) and empirical Freundlich model (EFM) were applied to the single-solute sorption of phenol or trichloroethylene from water onto monolayer or multilayer CTAB-montmorillonite. The parameters contained in the MLM and EFM were determined for each solute by fitting to the single-solute isotherm data, and subsequently utilized in binary sorption. The extended Langmuir model (ELM) coupled with the single-solute MLM and the ideal adsorbed solution theory (IAST) coupled with the single-solute EFM were used to predict the binary sorption of phenol and trichloroethylene onto CTAB-montmorillonite. It was found that the EFM was better than the MLM at describing single-solute sorption from water onto CTAB-montmorillonite, and the IAST was better than the ELM at describing the binary sorption from water onto CTAB-montmorillonite.

Sorption kinetics and isotherm studies of a cationic dye using agricultural waste: broad bean peels.

PubMed

Hameed, B H; El-Khaiary, M I

2008-06-15

In this paper, broad bean peels (BBP), an agricultural waste, was evaluated for its ability to remove cationic dye (methylene blue) from aqueous solutions. Batch mode experiments were conducted at 30 degrees C. Equilibrium sorption isotherms and kinetics were investigated. The kinetic data obtained at different concentrations have been analyzed using pseudo-first-order, pseudo-second-order and intraparticle diffusion equations. The experimental data fitted very well the pseudo-first-order kinetic model. Analysis of the temportal change of q indicates that at the beginning of the process the overall rate of adsorption is controlled by film-diffusion, then at later stage intraparticle-diffusion controls the rate. Diffusion coefficients and times of transition from film to pore-diffusion control were estimated by piecewise linear regression. The experimental data were analyzed by the Langmuir and Freundlich models. The sorption isotherm data fitted well to Langmuir isotherm and the monolayer adsorption capacity was found to be 192.7 mg/g and the equilibrium adsorption constant Ka is 0.07145 l/mg at 30 degrees C. The results revealed that BBP was a promising sorbent for the removal of methylene blue from aqueous solutions.

Surface functionalized composite nanofibers for efficient removal of arsenic from aqueous solutions.

PubMed

Mohamed, Alaa; Osman, T A; Toprak, M S; Muhammed, M; Uheida, A

2017-08-01

A novel composites nanofiber was synthesized based on PAN-CNT/TiO 2 -NH 2 nanofibers using electrospinning technique followed by chemical modification of TiO 2 NPs. PAN-CNT/TiO 2 -NH 2 nanofiber were characterized by XRD, FTIR, SEM, and TEM. The effects of various experimental parameters such as initial concentration, contact time, and solution pH on As removal were investigated. The maximum adsorption capacity at pH 2 for As(III) and As(V) is 251 mg/g and 249 mg/g, respectively, which is much higher than most of the reported adsorbents. The adsorption equilibrium reached within 20 and 60 min as the initial solution concentration increased from 10 to 100 mg/L, and the data fitted well using the linear and nonlinear pseudo first and second order model. Isotherm data fitted well to the linear and nonlinear Langmuir, Freundlich, and Redlich-Peterson isotherm adsorption model. Desorption results showed that the adsorption capacity can remain up to 70% after 5 times usage. This work provides a simple and an efficient method for removing arsenic from aqueous solution. Copyright © 2017 Elsevier Ltd. All rights reserved.

BTEX and MTBE adsorption onto raw and thermally modified diatomite.

PubMed

Aivalioti, Maria; Vamvasakis, Ioannis; Gidarakos, Evangelos

2010-06-15

The removal of BTEX (benzene, toluene, ethyl-benzene and xylenes) and MTBE (methyl tertiary butyl ether) from aqueous solution by raw (D(R)) and thermally modified diatomite at 550, 750 and 950 degrees C (D(550), D(750) and D(950) respectively) was studied. Physical characteristics of both raw and modified diatomite such as specific surface, pore volume distribution, porosity and pH(solution) were determined, indicating important structural changes in the modified diatomite, due to exposure to high temperatures. Both adsorption kinetic and isotherm experiments were carried out. The kinetics data proved a closer fit to the pseudo-second order model. Maximum values for the rate constant, k(2), were obtained for MTBE and benzene (48.9326 and 18.0996 g mg(-1)h(-1), respectively) in sample D(550). The isotherm data proved to fit the Freundlich model more closely, which produced values of the isotherm constant 1/n higher than one, indicating unfavorable adsorption. The highest adsorption capacity, calculated through the values of the isotherm constant k(F), was obtained for MTBE (48.42 mg kg(-1) (mg/L)(n)) in sample D(950). Copyright 2010 Elsevier B.V. All rights reserved.

A comparative study of the biosorption of iron(III)-cyanide complex anions to Rhizopus arrhizus and Chlorella vulgaris

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aksu, Z.; Calik, A.

1999-03-01

In this study a comparative biosorption of iron(III)-cyanide complex anions from aqueous solutions to Rhizopus arrhizus and Chlorella vulgaris was investigated. The iron(III)-cyanide complex ion-binding capacities of the biosorbents were shown as a function of initial pH, initial iron(III)-cyanide complex ion, and biosorbent concentrations. The results indicated that a significant reduction of iron(III)-cyanide complex ions was achieved at pH 13, a highly alkaline condition for both the biosorbents. The maximum loading capacities of the biosorbents were found to be 612.2 mg/g for R.arrhizus at 1,996.2 mg/L initial iron(III)-cyanide complex ion concentration and 387.0 mg/g for C. vulgaris at 845.4 mg/Lmore » initial iron(III)-cyanide complex ion concentration at this pH. The Freundlich, Langmuir, and Redlich-Peterson adsorption models were fitted to the equilibrium data at pH 3, 7, and 13. The equilibrium data of the biosorbents could be best fitted by all the adsorption models over the entire concentration range at pH 13.« less

Removal of fluoride from drinking water by cellulose@hydroxyapatite nanocomposites.

PubMed

Yu, Xiaolin; Tong, Shengrui; Ge, Maofa; Zuo, Junchao

2013-01-30

Cellulose@hydroxyapatite (HA) nanocomposites were prepared in NaOH/thiourea/urea/H(2)O solution via situ hybridization. The composite materials combine the advantage of cellulose and HA with the high specific surface area and the strong affinity toward fluoride. The composite materials were characterized by FTIR, SEM, XRD, TG and XPS, and the adsorption of fluoride was investigated. Adsorption kinetics indicated the adsorption equilibrium of fluoride was within 360 min and the adsorption process was well described by the pseudo-second-order kinetic model. The Langmuir and Freundlich isotherm models could fit the experimental data well. At the initial fluoride concentration of 10mg/L, the residual concentration using above 3g/L adsorbent dose could meet the drinking water standard of WHO norms. Furthermore, the coexisting anions had no significant effect on fluoride adsorption. Copyright © 2012 Elsevier Ltd. All rights reserved.

Functionalization of CNTs surface with phosphonuim based deep eutectic solvents for arsenic removal from water

NASA Astrophysics Data System (ADS)

AlOmar, Mohamed Khalid; Alsaadi, Mohammed Abdulhakim; Hayyan, Maan; Akib, Shatirah; Hashim, Mohd Ali

2016-12-01

Herein, we present the use of deep eutectic solvent (DES) as functionalization agents for carbon nanotubes (CNTs) to form novel adsorbents for removal of arsenic ions (As3+) from water. Two DESs systems were prepared using methyltriphenylphosphonium bromide (MTPB) and benzyltriphenylphosphonium chloride (BTPC) as salts, in conjugation with glycerol (Gly) as a hydrogen bond donor. The resulting novel adsorbents were characterized using thermogravimetric analysis (TGA), Zeta potential, Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, XRD, EDX, FESEM, and BET surface area. Optimization studies were carried out utilizing RSM-CCD experimental design to estimate the optimum removal conditions for each adsorbent. The adsorption experimental data of both adsorbents were found to fit well with pseudo-second-order kinetics model, as well as with Langmuir and Freundlich adsorption isotherm models. The maximum adsorption capacity of a MTPB-DES-functionalized CNTs adsorbent was 23.4 mg/g.

The biosorption of heavy metals from aqueous solution by Spirogyra and Cladophora filamentous macroalgae.

PubMed

Lee, Yi-Chao; Chang, Shui-Ping

2011-05-01

The aim of this research was to develop a low cost adsorbent for wastewater treatment. The prime objective of this study was to search for suitable freshwater filamentous algae that have a high heavy metal ion removal capability. This study evaluated the biosorption capacity from aqueous solutions of the green algae species, Spirogyra and Cladophora, for lead (Pb(II)) and copper (Cu(II)). In comparing the analysis of the Langmuir and Freundlich isotherm models, the adsorption of Pb(II) and Cu(II) by these two types of biosorbents showed a better fit with the Langmuir isotherm model. In the adsorption of heavy metal ions by these two types of biosorbents, chemical and physical adsorption of particle surfaces was perhaps more significant than diffusion and adsorption between particles. Continuous adsorption-desorption experiments discovered that both types of biomass were excellent biosorbents with potential for further development. Copyright © 2011 Elsevier Ltd. All rights reserved.

Sorption-desorption of carbamazepine by palygorskite-montmorillonite (PM) filter medium.

PubMed

Berhane, Tedros M; Levy, Jonathan; Krekeler, Mark P S; Danielson, Neil D; Stalcup, Apryll

2015-01-23

Palygorskite-montmorillonite (PM) was studied as a potential sewage treatment effluent filter material for carbamazepine. Batch sorption experiments were conducted as a function of granule size (0.3-0.6, 1.7-2.0 and 2.8mm) and different sewage effluent conditions (pH, ionic strength and temperature). Results showed PM had a mix of fibrous and plate-like morphologies. Sorption and desorption isotherms were fitted to the Freundlich model. Sorption is granule size-dependent and the medium granule size would be an appropriate size for optimizing both flow and carbamazepine retention. Highest and lowest sorption capacities corresponded to the smallest and the largest granule sizes, respectively. The lowest and the highest equilibrium aqueous (Ce) and sorbed (qe) carbamazepine concentrations were 0.4 mg L(-1) and 4.5 mg L(-1), and 0.6 mg kg(-1) and 411.8 mg kg(-1), respectively. Observed higher relative sorption at elevated concentrations with a Freundlich exponent greater than one, indicated cooperative sorption. The sorption-desorption hysteresis (isotherm non-singularity) indicated irreversible sorption. Higher sorption observed at higher rather than at lower ionic strength conditions is likely due to a salting-out effect. Negative free energy and the inverse sorption capacity-temperature relationship indicated the carbamazepine sorption process was favorable or spontaneous. Solution pH had little effect on sorption. Copyright © 2014 Elsevier B.V. All rights reserved.

Adsorption of Uranyl Ions at the Nano-hydroxyapatite and Its Modification

NASA Astrophysics Data System (ADS)

Skwarek, Ewa; Gładysz-Płaska, Agnieszka; Bolbukh, Yuliia

2017-04-01

Nano-hydroxyapatite and its modification, hydroxyapatite with the excess of phosphorus (P-HAP) and hydroxyapatite with the carbon ions built into the structure (C-HAP), were prepared by the wet method. They were studied by means of XRD, accelerated surface area and porosimetry (ASAP), and SEM. The size of crystallites computed using the Scherrer method was nano-hydroxyapatite (HAP) = 20 nm; P-HAP—impossible to determine; C-HAP = 22 nm; nano-HAP/U(VI) = 13.7 nm; P-HAP/U(VI)—impossible to determine, C-HAP/U(VI) = 11 nm. There were determined basic parameters characterizing the double electrical layer at the nano-HAP/electrolyte and P-HAP/electrolyte, C-HAP/electrolyte inter faces: density of the surface charge and zeta potential. The adsorption properties of nano-HAP sorbent in relation to U(VI) ions were studied by the batch technique. The adsorption processes were rapid in the first 60 min and reached the equilibrium within approximately 120 min (for P-HAP) and 300 min (for C-HAP and nano-HAP). The adsorption process fitted well with the pseudo-second-order kinetics. The Freundlich, Langmuir-Freundlich, and Dubinin-Radushkevich models of isotherms were examined for their ability to the equilibrium sorption data. The maximum adsorption capabilities ( q m ) were 7.75 g/g for P-HAP, 1.77 g/g for C-HAP, and 0.8 g/g for HAP at 293 K.

Effects of metal ions and pH on ofloxacin sorption to cassava residue-derived biochar.

PubMed

Huang, Peng; Ge, Chengjun; Feng, Dan; Yu, Huamei; Luo, Jiwei; Li, Jiatong; Strong, P J; Sarmah, Ajit K; Bolan, Nanthi S; Wang, Hailong

2018-03-01

In this study, the impacts of various cations, cation strength and pH on ofloxacin (OFL) adsorption to cassava residue-derived biochars were determined. The associated adsorption mechanisms are discussed. The biochars were prepared at pyrolysis temperatures ranging from 350°C to 750°C, and labeled as CW350, CW450, CW550, CW650 and CW750. The Freundlich model provided the best fit to describe the adsorption capacity of OFL and the Freundlich coefficient (logK f ) increased with increasing pyrolysis temperature. The inclusion of Zn 2+ or Al 3+ increased OFL sorption capacities of five biochars, while Cu 2+ reduced sorption to CW450 and CW550. No significant impacts on OFL sorption were observed in the presence of K + and Ca 2+ . The concentration of Ca 2+ affected the adsorption capacity of CW550, but had no significant impact on other biochars. The pH of OFL solution, ranging from 3 to 9, had no significant changes on OFL adsorption by all the tested biochars. Results of FTIR spectra and zeta potential indicated that electrostatic interactions, cationic exchange, metal bridging and micropore filling could be the main sorption mechanism between OFL and biochars. These studies indicated that cassava residue can be converted into biochars that are effective adsorbents for removing OFL from aqueous solution. Copyright © 2017 Elsevier B.V. All rights reserved.

Powdered activated carbon adsorption of two fishy odorants in water: Trans,trans-2,4-heptadienal and trans,trans-2,4-decadienal.

PubMed

Li, Xin; Wang, Jun; Zhang, Xiaojian; Chen, Chao

2015-06-01

Powdered activated carbon (PAC) adsorption of two fishy odorants, trans,trans-2,4-heptadienal (HDE) and trans,trans-2,4-decadienal (DDE), was investigated. Both the pseudo first-order and the pseudo second-order kinetic models well described the kinetics curves, and DDE was more readily removed by PAC. In isotherm tests, both Freundlich and Modified Freundlich isotherms fitted the experimental data well. PAC exhibited a higher adsorption capacity for DDE than for HDE, which could be ascribed to the difference in their hydrophobicity. The calculated thermodynamic parameters (ΔG0, ΔH0, and ΔS0) indicated an exothermic and spontaneous adsorption process. PAC dosage, pH, and natural organic matter (NOM) presence were found to influence the adsorption process. With increasing PAC dosage, the pseudo first-order and pseudo second-order rate constants both increased. The value of pH had little influence on HDE or DDE molecules but altered the surface charge of PAC, and the maximum adsorption capacity occurred at pH9. The presence of NOM, especially the fraction with molecular weight less than 1k Dalton, hindered the adsorption. The study showed that preloaded NOM impaired the adsorption capacity of HDE or DDE more severely than simultaneously fed NOM did. Copyright © 2015. Published by Elsevier B.V.

Removal of chromium (VI) from aqueous solution using walnut hull.

PubMed

Wang, Xue Song; Li, Zhi Zhong; Tao, Sheng Rong

2009-02-01

In this study, removal of chromium (VI) from aqueous solution by walnut hull (a local low-cost adsorbent) was studied. The extent of adsorption was investigated as a function of solution pH, contact time, adsorbent and adsorbate concentration, reaction temperature and supporting electrolyte (sodium chloride). The Cr (VI) removal was pH-dependent, reaching a maximum (97.3%) at pH 1.0. The kinetic experimental data were fitted to the first-order, modified Freundlich, intraparticle diffusion and Elovich models and the corresponding parameters were obtained. A 102.78 kJ/mol Ea (activation energy) for the reaction of chromium (VI) adsorption onto walnut indicated that the rate-limiting step in this case might be a chemically controlled process. Both the Langmuir and Freundlich isotherms were suitable for describing the biosorption of chromium (VI) onto walnut hull. The uptake of chromium (VI) per weight of adsorbent increased with increasing initial chromium (VI) concentration up to 240-480 mg/L, and decreased sharply with increasing adsorbent concentration ranging from 1.0 to 5.0 g/L. An increase in sodium chloride (as supporting electrolyte) concentration was found to induce a negative effect while an increase in temperature was found to give rise to a positive effect on the chromium (VI) adsorption process. Compared to the various other adsorbents reported in the literature, the walnut hull in this study shows very good promise for practical applicability.

Study of 2,4-dichlorophenoxyacetic acid (2,4-D) removal by Cu-Fe-layered double hydroxide from aqueous solution

NASA Astrophysics Data System (ADS)

Nejati, Kamellia; Davary, Soheila; Saati, Marziye

2013-09-01

The hydrotalcite-like compound of Cu-Fe-layered double hydroxide was studied as a potential adsorbent of herbicide 2,4-dichlorophenoxyacetic acid (2,4-D). The nanoparticles of Cu-Fe layered double hydroxide were prepared by Cu/Fe molar ratio of 2:1 using a coprecipitation method at pH 8.5 and characterized by the X-ray powder diffraction (XRD), the Fourier transform infrared spectroscopy (FT-IR), the thermal gravimetric analysis (TGA) and the elemental analysis. The size and morphology of nanoparticles were examined by the transmission electron microscopy (TEM). The adsorption experiments on LDH, on the other hand, were conducted in three different procedures, namely, time-dependent, pH-dependent and temperature-dependent. Characterization of the adsorption products by the XRD method indicates that the intercalation of 2,4-D between the LDH layers has not occurred and the surface adsorption had taken place. The adsorption kinetic was tested for pseudo-first-order, pseudo-second-order, Elovich and Intra-particle diffusion kinetic models and the rate constants were calculated. The equilibrium adsorption data were described by Langmuir and Freundlich equations. It was observed that, the Langmuir isotherm slightly better fitted to the experimental data rather than that of Freundlich. In the adsorption experiments, the Gibbs free energy values, ΔG°, the enthalpy, ΔH°, and the entropy, ΔS° were also determined.

Sorption-desorption and biosorption of bisphenol A, triclosan, and 17α-ethinylestradiol to sewage sludge.

PubMed

Banihashemi, Bahman; Droste, Ronald L

2014-07-15

To better understand the fate of microconstituents (MCs) in an activated sludge (AS) system, sorption, biosorption, and desorption studies were investigated at μg/L range for 17α-ethinylestradiol (EE2), bisphenol A (BPA), and triclosan (TCS). Batch experiments with activated and deactivated sludge originating from continuous flow porous pot reactors operating at solid retention times (SRTs) of 5, 10, and 15 days were conducted in order to investigate the sorption kinetics and distinguish physicochemical sorption and biosorption. The effect of SRT and the biomass concentration on sorption kinetics were also studied. Selected MCs showed high sorption affinity to the non-viable biomass during the first 30 min of the experiment, which was gradually reduced until equilibrium was reached. Desorption results showed two distinct stages, a very rapid desorption within 20 min followed by a slow desorption stage. Biosorption study indicated that the soluble concentrations of target compounds decreased rapidly for selected MCs similar to the sorption study; however, the soluble and solid phase concentrations continued to decrease slowly during the length of the experiment which indicates the possible biodegradation of these compounds in both phases. Finally, mathematical models were applied to describe the sorption mechanism and Freundlich sorption isotherms with values of 1/n close to 1 were found to best fit the results which demonstrate that all tested concentrations result on the linear part of the Freundlich isotherm. Calculation of the Freundlich constant, KF and distribution coefficient, Kd exhibited the greater tendency of EE2 and TCS for sorption, compared to BPA. The results of this study indicated that the SRT had a clear effect on the sorption kinetics where the highest sorption rate constant was achieved for a SRT of 10 days for all three target substances. This could be due to change of the morphology of the biomass from reactors operating at different SRTs. Copyright © 2014 Elsevier B.V. All rights reserved.

Adsorption kinetics of malachite green onto activated carbon prepared from Tunçbilek lignite.

PubMed

Onal, Y; Akmil-Başar, C; Eren, Didem; Sarici-Ozdemir, Cigdem; Depci, Tolga

2006-02-06

Adsorbent (T3K618) has been prepared from Tunçbilek lignite by chemical activation with KOH. Pore properties of the activated carbon such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by t-plot based on N2 adsorption isotherm. The N2 adsorption isotherm of malachite green on T3K618 is type I. The BET surface area of the adsorbent which was primarily contributed by micropores was determined 1000 m2/g. T3K618 was used to adsorb malachite green (MG) from an aqueous solution in a batch reactor. The effects of initial dye concentration, agitation time, initial pH and adsorption temperature have been studied. It was also found that the adsorption isotherm followed both Freundlich and Dubinin-Radushkevich models. However, the Freundlich gave a better fit to all adsorption isotherms than the Dubinin-Radushkevich. The kinetics of adsorption of MG has been tested using pseudo-first-order, pseudo-second-order and intraparticle diffusion models. Results show that the adsorption of MG from aqueous solution onto micropores T3K618 proceeds according to the pseudo-second-order model. The intraparticle diffusion of MG molecules within the carbon particles was identified to be the rate-limiting step. The adsorption of the MG was endothermic (DeltaH degrees = 6.55-62.37 kJ/mol) and was accompanied by an increase in entropy (DeltaS degrees = 74-223 J/mol K) and a decrease in mean value of Gibbs energy (DeltaG degrees = -6.48 to -10.32 kJ/mol) in the temperature range of 20-50 degrees C.

Adsorption kinetics, isotherm, and thermodynamics studies of acetyl-11-keto-β-boswellic acids (AKBA) from Boswellia serrata extract using macroporous resin.

PubMed

Niphadkar, Sonali S; Rathod, Virendra K

2017-09-14

An acetyl-11-keto-β-boswellic acid (AKBA) is potent anti-inflammatory agent found in Boswellia serrata oleogum resin. Adsorption characteristics of AKBA from B. serrata were studied using macroporous adsorbent resin to understand separation and adsorption mechanism of targeted molecules. Different macroporous resins were screened for adsorption and desorption of AKBA and Indion 830 was screened as it showed higher adsorption capacity. The kinetic equations were studied and results showed that the adsorption of AKBA on Indion 830 was well fitted to the pseudo first-order kinetic model. The influence of two parameters such as temperature (298, 303, and 308 K) and pH (5-8) on the adsorption process was also studied. The experimental data was further investigated using Langmuir, Freundlich, and Temkin isotherm models. It was observed that Langmuir isotherm model was found to be the best fit for AKBA adsorption by Indion 830 and highest adsorption capacity (50.34 mg/g) was obtained at temperature of 303 K. The values of thermodynamic parameters such as the change of Gibbs free energy (ΔG*), entropy (ΔS*), and enthalpy (ΔH*), indicated that the process of adsorption was spontaneous, favourable, and exothermic.

Selective removal of erythromycin by magnetic imprinted polymers synthesized from chitosan-stabilized Pickering emulsion.

PubMed

Ou, Hongxiang; Chen, Qunhui; Pan, Jianming; Zhang, Yunlei; Huang, Yong; Qi, Xueyong

2015-05-30

Magnetic imprinted polymers (MIPs) were synthesized by Pickering emulsion polymerization and used to adsorb erythromycin (ERY) from aqueous solution. The oil-in-water Pickering emulsion was stabilized by chitosan nanoparticles with hydrophobic Fe3O4 nanoparticles as magnetic carrier. The imprinting system was fabricated by radical polymerization with functional and crosslinked monomer in the oil phase. Batches of static and dynamic adsorption experiments were conducted to analyze the adsorption performance on ERY. Isotherm data of MIPs well fitted the Freundlich model (from 15 °C to 35 °C), which indicated heterogeneous adsorption for ERY. The ERY adsorption capacity of MIPs was about 52.32 μmol/g at 15 °C. The adsorption kinetics was well described by the pseudo-first-order model, which suggested that physical interactions were primarily responsible for ERY adsorption. The Thomas model used in the fixed-bed adsorption design provided a better fit to the experimental data. Meanwhile, ERY exhibited higher affinity during adsorption on the MIPs compared with the adsorption capacity of azithromycin and chloramphenicol. The MIPs also exhibited excellent regeneration capacity with only about 5.04% adsorption efficiency loss in at least three repeated adsorption-desorption cycles. Copyright © 2015 Elsevier B.V. All rights reserved.

Synthesis of activated carbon-based amino phosphonic acid chelating resin and its adsorption properties for Ce(III) removal.

PubMed

Chen, Tao; Yan, Chunjie; Wang, Yixia; Tang, Conghai; Zhou, Sen; Zhao, Yuan; Ma, Rui; Duan, Ping

2015-01-01

This work aims to investigate the adsorption of Ce(III) onto chelating resin based on activated carbon (CRAC). The CRAC adsorbent was prepared from activated carbon (AC) followed by oxidation, silane coupling, ammoniation and phosphorylation, and characterized by Fourier transform-infrared spectrometry, nitrogen adsorption measurements and scanning electron microscopy. The effects of solution pH, adsorbent dosage and contact time were studied by batch technique. Langmuir and Freundlich isotherms were used to describe the adsorption behaviour of Ce(III) by CRAC, and the results showed that the adsorption behaviour well fitted the Langmuir model. The maximum uptake capacity (qmax) calculated by using the Langmuir equation for cerium ions was found to be 94.34 mg/g. A comparison of the kinetic models and the overall experimental data was best fitted with the type 1 pseudo second-order kinetic model. The calculated thermodynamic parameters (ΔG°, ΔH° and ΔS°) showed that the adsorption for Ce(III) was feasible, spontaneous and exothermic at 25-45 °C. The CRAC showed an excellent adsorptive selectivity towards Ce(III). Moreover, more than 82% of Ce(III) adsorbed onto CRAC could be desorbed with HCl and could be used several times.

An eco-friendly dyeing of woolen yarn by Terminalia chebula extract with evaluations of kinetic and adsorption characteristics.

PubMed

Shabbir, Mohd; Rather, Luqman Jameel; Shahid-Ul-Islam; Bukhari, Mohd Nadeem; Shahid, Mohd; Ali Khan, Mohd; Mohammad, Faqeer

2016-05-01

In the present study Terminalia chebula was used as an eco-friendly natural colorant for sustainable textile coloration of woolen yarn with primary emphasis on thermodynamic and kinetic adsorption aspects of dyeing processes. Polyphenols and ellagitannins are the main coloring components of the dye extract. Assessment of the effect of pH on dye adsorption showed an increase in adsorption capacity with decreasing pH. Effect of temperature on dye adsorption showed 80 °C as optimum temperature for wool dyeing with T. chebula dye extract. Two kinetic equations, namely pseudo first-order and pseudo second-order equations, were employed to investigate the adsorption rates. Pseudo second-order model provided the best fit (R (2) = 0.9908) to the experimental data. The equilibrium adsorption data were fitted by Freundlich and Langmuir isotherm models. The adsorption behavior accorded well (R (2) = 0.9937) with Langmuir isotherm model. Variety of eco-friendly and sustainable shades were developed in combination with small amount of metallic mordants and assessed in terms of colorimetric (CIEL(∗) a (∗) b (∗) and K/S) properties measured using spectrophotometer under D65 illuminant (10° standard observer). The fastness properties of dyed woolen yarn against light, washing, dry and wet rubbing were also evaluated.

Environmentally friendly biosorbents (husks, pods and seeds) from Moringa oleifera for Pb(II) removal from contaminated water.

PubMed

Tavares, Fernanda Oliveira; Pinto, Laura Adriane de Moraes; Bassetti, Fátima de Jesus; Vieira, Marcelo Fernandes; Bergamasco, Rosângela; Vieira, Angélica Marquetotti Salcedo

2017-12-01

Lead is a heavy metal considered highly toxic, responsible for causing several health problems as well as being extremely harmful to fauna and flora. Given this fact, several techniques have been studied for the removal of this metal from contaminated water, in which stands out adsorption. In this sense, the objective of this study was to evaluate the potential of lead(II) biosorption from contaminated water by seed husks, seeds and pods of Moringa oleifera Lam (moringa). Biomass was characterized by energy-dispersive X-ray spectroscopy, Scanning Electron Microscopy and Fourier transform infrared spectroscopy analyses. From the studied parameters, the optimal conditions obtained for the three analyzed biosorbents are: 30 min to equilibrium, pH 6 and 25°C temperature. The pseudo-second-order kinetic model was the best fitted to the experimental data for the three evaluated biosorbents. Regarding the adsorption isotherms, the model that best fitted to the experimental data for seed and seed husk was that proposed by Freundlich, and for the pod the Langmuir model. The analysis of the obtained thermodynamic data showed that the adsorption process is favorable and of exothermic nature. Through the results it was concluded that the evaluated biosorbents are efficient in lead(II) biosorption.

An eco-friendly dyeing of woolen yarn by Terminalia chebula extract with evaluations of kinetic and adsorption characteristics

PubMed Central

Shabbir, Mohd; Rather, Luqman Jameel; Shahid-ul-Islam; Bukhari, Mohd Nadeem; Shahid, Mohd; Ali Khan, Mohd; Mohammad, Faqeer

2016-01-01

In the present study Terminalia chebula was used as an eco-friendly natural colorant for sustainable textile coloration of woolen yarn with primary emphasis on thermodynamic and kinetic adsorption aspects of dyeing processes. Polyphenols and ellagitannins are the main coloring components of the dye extract. Assessment of the effect of pH on dye adsorption showed an increase in adsorption capacity with decreasing pH. Effect of temperature on dye adsorption showed 80 °C as optimum temperature for wool dyeing with T. chebula dye extract. Two kinetic equations, namely pseudo first-order and pseudo second-order equations, were employed to investigate the adsorption rates. Pseudo second-order model provided the best fit (R2 = 0.9908) to the experimental data. The equilibrium adsorption data were fitted by Freundlich and Langmuir isotherm models. The adsorption behavior accorded well (R2 = 0.9937) with Langmuir isotherm model. Variety of eco-friendly and sustainable shades were developed in combination with small amount of metallic mordants and assessed in terms of colorimetric (CIEL∗a∗b∗ and K/S) properties measured using spectrophotometer under D65 illuminant (10° standard observer). The fastness properties of dyed woolen yarn against light, washing, dry and wet rubbing were also evaluated. PMID:27222752

Biosorption of hexavalent chromium from aqueous solutions by Macadamia nutshell powder

NASA Astrophysics Data System (ADS)

Pakade, Vusumzi Emmanuel; Ntuli, Themba Dominic; Ofomaja, Augustine Enakpodia

2017-10-01

Macadamia nutshell biosorbents treated in three different activating agents [raw Macadamia nutshell powder (RMN), acid-treated Macadamia nutshell (ATMN) and base-treated Macadamia nutshell (BTMN)] were investigated for the adsorption of hexavalent chromium [Cr(VI)] from aqueous solutions. Fourier transform infrared spectroscopy spectra of free and Cr(VI)-loaded sorbents as well as thermogravimetric analysis revealed that the acid and base treatments modified the surface properties of the sorbent. Surface characteristics were also evaluated by the scanning electron microscopy and surface area analyzer. The optimum conditions for the adsorption of Cr(VI) by sorbents were pH 2, contact time 10 h, adsorbent mass 0.2 g and concentration 100 mg L-1. The equilibrium data were fitted into the Langmuir, Freundlich, Redlich-Peterson and Sips isotherms, and no single model could clearly explain the sorption mechanism. Maximum binding capacities of 45.23, 44.83 and 42.44 mg g-1 for RMN, ATMN and BTMN, respectively, were obtained. The kinetic data were analyzed using the pseudo-first, pseudo-second and Elovich kinetic models, and it was observed that the pseudo-second-order model produced the best fit for the experimental data. Macadamia nutshell sorbents showed potential as low-cost adsorbent for the removal of Cr(VI) from aqueous solution.

Remediation of phosphate-contaminated water by electrocoagulation with aluminium, aluminium alloy and mild steel anodes.

PubMed

Vasudevan, Subramanyan; Lakshmi, Jothinathan; Jayaraj, Jeganathan; Sozhan, Ganapathy

2009-05-30

The present study provides an electrocoagulation process for the remediation of phosphate-contaminated water using aluminium, aluminium alloy and mild steel as the anodes and stainless steel as the cathode. The various parameters like effect of anode materials, effect of pH, concentration of phosphate, current density, temperature and co-existing ions, and so forth, and the adsorption capacity was evaluated using both Freundlich and Langmuir isotherm models. The adsorption of phosphate preferably fitting the Langmuir adsorption isotherm suggests monolayer coverage of adsorbed molecules. The results showed that the maximum removal efficiency of 99% was achieved with aluminium alloy anode at a current density of 0.2 A dm(-2), at a pH of 7.0. The adsorption process follows second-order kinetics.

Adsorption of Crystal Violet on Activated Carbon Prepared from Coal Flotation Concentrate

NASA Astrophysics Data System (ADS)

Aydogmus, Ramazan; Depci, Tolga; Sarikaya, Musa; Riza Kul, Ali; Onal, Yunus

2016-10-01

The objective of this study is firstly to investigate the floatability properties of Zilan- Van coal after microwave irradiation and secondly to produce activated carbon from flotation concentrate in order to remove Crystal Violet (CV) from waste water. The flotation experiments showed that microwave heating at 0.9 kW power level for 60 sec exposure time enhanced the hydrophobicity and increased the flotation yield. The activated carbon with remarkable surface area (696 m2/g) was produced from the flotation concentrate and used to adsorb CV from aqueous solution in a batch reactor at different temperature. The adsorption properties of CV onto the activated carbon are discussed in terms of the adsorption isotherms (Langmuir and Freundlich) and found that the experimental results best fitted by the Langmuir model.

Removal of Malachite Green Dye by Mangifera indica Seed Kernel Powder

NASA Astrophysics Data System (ADS)

Singh, Dilbagh; Sowmya, V.; Abinandan, S.; Shanthakumar, S.

2017-11-01

In this study, batch experiments were carried out to study the adsorption of Malachite green dye from aqueous solution by Mangifera indica (mango) seed kernel powder. The mango seed kernel powder was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. Effect of various parameters including pH, contact time, adsorbent dosage, initial dye concentration and temperature on adsorption capacity of the adsorbent was observed and the optimized condition for maximum dye removal was identified. Maximum percentage removal of 96% was achieved with an adsorption capacity of 22.8 mg/g at pH 6 with an initial concentration of 100 mg/l. The equilibrium data were examined to fit the Langmuir and Freundlich isotherm models. Thermodynamic parameters for the adsorption process were also calculated.

Composite anion-exchangers modified with nanoparticles of hydrated oxides of multivalent metals

NASA Astrophysics Data System (ADS)

Maltseva, T. V.; Kolomiets, E. O.; Dzyazko, Yu. S.; Scherbakov, S.

2018-02-01

Organic-inorganic composite ion-exchangers based on anion exchange resins have been obtained. Particles of one-component and two-component modifier were embedded using the approach, which allows us to realize purposeful control of a size of the embedded particles. The approach is based on Ostwald-Freundlich equation, which was adapted to deposition in ion exchange matrix. The equation was obtained experimentally. Hydrated oxides of zirconium and iron were applied to modification, concentration of the reagents were varied. The embedded particles accelerate sorption, the rate of which is fitted by the model equation of chemical reactions of pseudo-second order. When sorption of arsenate ions from very diluted solution (50 µg dm-3) occurs, the composites show higher distribution coefficients comparing with the pristine resin.

Adsorption of emerging pollutants on functionalized multiwall carbon nanotubes.

PubMed

Patiño, Yolanda; Díaz, Eva; Ordóñez, Salvador; Gallegos-Suarez, Esteban; Guerrero-Ruiz, Antonio; Rodríguez-Ramos, Inmaculada

2015-10-01

Adsorption of three representative emerging pollutants - 1,8-dichlorooctane, nalidixic acid and 2-(4-methylphenoxy)ethanol- on different carbon nanotubes was studied in order to determine the influence of the morphological and chemical properties of the materials on their adsorption properties. As adsorbents, multiwall carbon nanotubes (MWCNTs) without functionalization and with oxygen or nitrogen surface groups, as well as carbon nanotubes doped with nitrogen were used. The adsorption was studied in aqueous phase using batch adsorption experiments, results being fitted to both Langmuir and Freundlich models. The adsorption capacity is strongly dependent on both the hydrophobicity of the adsorbates and the morphology of the adsorbents. Thermodynamic parameters were determined observing strong interactions between the aromatic rings of the emerging pollutant and the nitrogen modified adsorbents. Copyright © 2015 Elsevier Ltd. All rights reserved.

β-TCP porous pellets as an orthopaedic drug delivery system: ibuprofen/carrier physicochemical interactions

NASA Astrophysics Data System (ADS)

Baradari, Hiba; Damia, Chantal; Dutreih-Colas, Maggy; Champion, Eric; Chulia, Dominique; Viana, Marylène

2011-10-01

Calcium phosphate bone substitute materials can be loaded with active substances for in situ, targeted drug administration. In this study, porous β-TCP pellets were investigated as an anti-inflammatory drug carrier. Porous β-TCP pellets were impregnated with an ethanolic solution of ibuprofen. The effects of contact time and concentration of ibuprofen solution on drug adsorption were studied. The ibuprofen adsorption equilibrium time was found to be one hour. The adsorption isotherms fitted to the Freundlich model, suggesting that the interaction between ibuprofen and β-TCP is weak. The physicochemical characterizations of loaded pellets confirmed that the reversible physisorption of ibuprofen on β-TCP pellets is due to Van der Waals forces, and this property was associated with the 100% ibuprofen release.

Ni(II) biosorption by Cassia fistula (Golden Shower) biomass.

PubMed

Hanif, Muhammad Asif; Nadeem, Raziya; Bhatti, Haq Nawaz; Ahmad, Najum Rashid; Ansari, Tariq Mehmood

2007-01-10

Cassia fistula is a fast-growing, medium-sized, deciduous tree which is now widely cultivated worldwide as an ornamental tree for its beautiful showy yellow flowers. Methods are required to reuse fallen leaves, branches, stem bark and pods when they start getting all over lawn. This investigation studies the use of these non-useful parts of C. fistula as naturally occurring biosorbent for the batch removal of Ni(II) in a well stirred system under different experimental conditions. The data showed that the maximum pH (pHmax) for efficient sorption of Ni(II) was 6 at which evaluated biosorbent dosage, biosorbent particle size, initial concentrations of Ni(II) and sorption time were 0.1 g/100 mL, <0.255 mm, up to 200 mg/L and 720 min, respectively. The experimental results were analyzed in terms of Langmuir and Freundlich isotherms. The Langmuir isotherm model fitted well to data of Ni(II) biosorption by C. fistula biomass as compared to the model of Freundlich. The kinetic studies showed that the sorption rates could be described better by a second order expression than by a more commonly applied Lagergren equation. The magnitude of the Gibbs free energy values indicates spontaneous nature of the sorption process. The sorption ability of C. fistula biomass for Ni(II) removal tends to be in the order: leaves

Improvement of pesticide adsorption capacity of cellulose fibre by high-energy irradiation-initiated grafting of glycidyl methacrylate

NASA Astrophysics Data System (ADS)

Takács, Erzsébet; Wojnárovits, László; Koczog Horváth, Éva; Fekete, Tamás; Borsa, Judit

2012-09-01

Cellulose as a renewable raw material was used for preparation of adsorbent of organic impurities in wastewater treatment. Hydrophobic surface of cellulose substrate was developed by grafting glycidyl methacrylate in simultaneous grafting using gamma irradiation initiation. Water uptake of cellulose significantly decreased while adsorption of phenol and a pesticide molecule (2,4-dichlorophenoxyacetic acid: 2,4-D) increased upon grafting. Adsorption equilibrium data fitted the Freundlich isotherm for both solutes.

Artificial Neural Network Modeling and Genetic Algorithm Optimization for Cadmium Removal from Aqueous Solutions by Reduced Graphene Oxide-Supported Nanoscale Zero-Valent Iron (nZVI/rGO) Composites

PubMed Central

Fan, Mingyi; Li, Tongjun; Hu, Jiwei; Cao, Rensheng; Wei, Xionghui; Shi, Xuedan; Ruan, Wenqian

2017-01-01

Reduced graphene oxide-supported nanoscale zero-valent iron (nZVI/rGO) composites were synthesized in the present study by chemical deposition method and were then characterized by various methods, such as Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The nZVI/rGO composites prepared were utilized for Cd(II) removal from aqueous solutions in batch mode at different initial Cd(II) concentrations, initial pH values, contact times, and operating temperatures. Response surface methodology (RSM) and artificial neural network hybridized with genetic algorithm (ANN-GA) were used for modeling the removal efficiency of Cd(II) and optimizing the four removal process variables. The average values of prediction errors for the RSM and ANN-GA models were 6.47% and 1.08%. Although both models were proven to be reliable in terms of predicting the removal efficiency of Cd(II), the ANN-GA model was found to be more accurate than the RSM model. In addition, experimental data were fitted to the Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherms. It was found that the Cd(II) adsorption was best fitted to the Langmuir isotherm. Examination on thermodynamic parameters revealed that the removal process was spontaneous and exothermic in nature. Furthermore, the pseudo-second-order model can better describe the kinetics of Cd(II) removal with a good R2 value than the pseudo-first-order model. PMID:28772901

Artificial Neural Network Modeling and Genetic Algorithm Optimization for Cadmium Removal from Aqueous Solutions by Reduced Graphene Oxide-Supported Nanoscale Zero-Valent Iron (nZVI/rGO) Composites.

PubMed

Fan, Mingyi; Li, Tongjun; Hu, Jiwei; Cao, Rensheng; Wei, Xionghui; Shi, Xuedan; Ruan, Wenqian

2017-05-17

Reduced graphene oxide-supported nanoscale zero-valent iron (nZVI/rGO) composites were synthesized in the present study by chemical deposition method and were then characterized by various methods, such as Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The nZVI/rGO composites prepared were utilized for Cd(II) removal from aqueous solutions in batch mode at different initial Cd(II) concentrations, initial pH values, contact times, and operating temperatures. Response surface methodology (RSM) and artificial neural network hybridized with genetic algorithm (ANN-GA) were used for modeling the removal efficiency of Cd(II) and optimizing the four removal process variables. The average values of prediction errors for the RSM and ANN-GA models were 6.47% and 1.08%. Although both models were proven to be reliable in terms of predicting the removal efficiency of Cd(II), the ANN-GA model was found to be more accurate than the RSM model. In addition, experimental data were fitted to the Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherms. It was found that the Cd(II) adsorption was best fitted to the Langmuir isotherm. Examination on thermodynamic parameters revealed that the removal process was spontaneous and exothermic in nature. Furthermore, the pseudo-second-order model can better describe the kinetics of Cd(II) removal with a good R² value than the pseudo-first-order model.

Adsorption of crude and engine oils from water using raw rice husk.

PubMed

Razavi, Zahra; Mirghaffari, Nourollah; Rezaei, Behzad

2014-01-01

The raw rice husk (RRH) was used as a low cost adsorbent to remove three oil compounds with different viscosities (crude oil, engine oil and spent engine oil) from an aqueous environment. Some of the sorbent specifications were characterized using a CHNSO analyzer, Fourier transform infrared, scanning electron microscope and inductively coupled plasma spectroscopy. With decreasing RRH particles size, the oil adsorption percentage was reduced for crude, spent and engine oils from 50 to 30%, 65 to 20% and 70 to 0.01%, respectively. This was probably due to damage of the microcavities. The removal percentage by sorbent at optimized conditions was 88, 80 and 55% for engine, spent and crude oils, respectively, corresponding to their descending viscosity. The adsorption of crude and spent oils on rice husk followed the Freundlich isotherm model, while the adsorption of engine oil was fitted by the Langmuir model. The maximum adsorption capacity (qmax), calculated from the Langmuir model for the adsorption of engine oil on RRH, was 1,250 mg/g.

Chromium (Ⅵ) removal from aqueous solutions through powdered activated carbon countercurrent two-stage adsorption.

PubMed

Wang, Wenqiang

2018-01-01

To exploit the adsorption capacity of commercial powdered activated carbon (PAC) and to improve the efficiency of Cr(VI) removal from aqueous solutions, the adsorption of Cr(VI) by commercial PAC and the countercurrent two-stage adsorption (CTA) process was investigated. Different adsorption kinetics models and isotherms were compared, and the pseudo-second-order model and the Langmuir and Freundlich models fit the experimental data well. The Cr(VI) removal efficiency was >80% and was improved by 37% through the CTA process compared with the conventional single-stage adsorption process when the initial Cr(VI) concentration was 50 mg/L with a PAC dose of 1.250 g/L and a pH of 3. A calculation method for calculating the effluent Cr(VI) concentration and the PAC dose was developed for the CTA process, and the validity of the method was confirmed by a deviation of <5%. Copyright © 2017. Published by Elsevier Ltd.

Sorption characteristics of pesticides on matrix substrates used in biopurification systems.

PubMed

De Wilde, Tineke; Spanoghe, Pieter; Ryckeboer, Jaak; Jaeken, Peter; Springael, Dirk

2009-03-01

On-farm biopurification systems were developed to remove pesticides from contaminated water generated at the farmyard. An important process in the system's efficiency is the sorption of pesticides to the substrates used in the biopurification systems. The composition and type of material present in the biobed are crucial for retention of chemicals. This study investigated the sorption of linuron, isoproturon, metalaxyl, isoxaben, bentazon and lenacil on substrates commonly used in a biopurification system, i.e. cow manure, straw, willow chopping, soil, coconut chips, garden waste compost, and peat mix. Linear, Freundlich, and Langmuir sorption isotherms were fitted to the obtained data. The best fit was obtained with the Freundlich model. More immobile pesticides (i.e. linuron and isoxaben) tended to associate with the organic substrate, while more mobile pesticides partition in the water (i.e. bentazon). According to sorption capacity, the substrates could be classified as peat mix > compost, coco chips, straw > cow manure, willow chopping > sandy loam soil. Sorption capacity was positively correlated with the organic carbon content, CaO and the cation exchange capacity. Furthermore, no significant differences in sorption could be found between technical and formulated isoproturon and bentazon. Moreover, the individual sorption coefficient K(d) was additive, which means that individual sorption coefficients can be used to calculate the sorption coefficients of a mixture of substrates. What concerns the mutual interaction of pesticides it could be observed that the sorption of linuron and metalaxyl was significantly lower in combination with isoproturon and bentazon, while the latter pesticides were not influenced by the presence of linuron and metalaxyl. As guidelines, firstly, it could be stated that using the most sorbing materials such as peat mix, might significantly increase the biopurification systems efficiency. Secondly, the treatment of very mobile pesticides, such as bentazon, should be taken with care as these will easily leach through the system. Additional chemical treatment might be necessary for these type of pesticides.

A review on the removal of antibiotics by carbon nanotubes.

PubMed

Cong, Qiao; Yuan, Xing; Qu, Jiao

2013-01-01

Increasing concerns have been raised regarding the potential risks of antibiotics to human and ecological health due to their extensive use. Carbon nanotubes (CNTs) have drawn special research attention because of their unique properties and potential applications as a kind of adsorbents. This review summarizes the currently available research on the adsorption of antibiotics on CNTs, and will provide useful information for CNT application and risk assessment. Four different models, the Freundlich model (FM), Langmuir model (LM), Polanyi-Mane model (PMM), and Dubinin-Ashtakhov model (DAM), are often used to fit the adsorption isotherms. Because different mechanisms may act simultaneously, including electrostatic interactions, hydrophobic interactions, π-π bonds, and hydrogen bonds, the prediction of organic chemical adsorption on CNTs is not straightforward. Properties of CNTs, such as specific surface area, adsorption sites, and oxygen content, may influence the adsorption of antibiotics on CNTs. Adsorption heterogeneity and hysteresis are two features of antibiotic-CNT interactions. In addition, CNTs with adsorbed antibiotics may have potential risks for human health. So, further research examining how to reduce such risks is needed.

Adsorption of Acid Blue 25 dye by bentonite and surfactant modified bentonite

NASA Astrophysics Data System (ADS)

Jeeva, Mark; Wan Zuhairi, W. Y.

2018-04-01

Adsorption of Acid Blue (AB 25) from water via batch adsorption experiments onto Na-Bentonite (NB) and CTAB-modified bentonite (CTAB-Ben) was investigated. Studies concerning the factors influencing the adsorption capacities of NB and CTAB-Ben, such as initial dye concentration, adsorbent dosage, pH, contact time and temperature were investigated and discussed. The results revealed that CTAB-modified bentonite demonstrated high adsorption capacities toward acid dyes, while NB exhibited sorption capacities lower than CTAB-Ben. The maximum adsorption efficiency was found to be 50% at an AB 25 concentration of 50 mg/L, adsorbent dosage of 1.8 g/L, reaction time of 90 min and equilibrium pH of 11. The results of isotherm study fit the Langmuir and Freundlich models (R2 > 0.93) and (R2 > 0.9) respectively.

A Preliminary Study of Europium Uptake by Yeast Cells. The Case of Kluveromyces Marxianus

NASA Astrophysics Data System (ADS)

Anagnostopoulos, V.; Symeopoulos, B.

2008-08-01

The objective of the present work is an exploration of a cost effective recovery of lanthanides, either for minimizing the industrial processes losses, or for reasons related to Radioactive Waste Management. Specifically, the uptake of europium from aqueous solutions by Kluveromyces marxianus cells was studied. Moreover, this biotechnological approach turns out to be environmental friendly, considering that cells of Kluveromyces marxianus are readily available as wastes from food fermentation industries. Europium [152Eu+154Eu]-labelled solutions were used providing better accuracy and reproducibility of measurements, mainly in low concentration range. The effect of pH, contact time and europium initial concentration were investigated. Adsorption data were fitted to Langmuir and Freundlich sorption models and Scatchard plots were used to reveal the existence of at least two types of binding sites.

Performance of different carbonaceous materials for emerging pollutants adsorption.

PubMed

Patiño, Yolanda; Díaz, Eva; Ordóñez, Salvador

2015-01-01

The adsorption of three representative emerging pollutants over different kinds of carbonaceous adsorbents has been studied in this work. The adsorbates were nalidixic acid (NAL, representative of a pharmaceutical), 1,8-dichlorooctane (DCO, a chloroparaffin) and methyl-phenoxy-ethanol (MPET, a surfactant). Activated carbons, carbon nanofibers, carbon nanotubes and high surface area graphites have been tested as adsorbents. Adsorption isotherms, carried out in a batch system, were fitted using both a Langmuir and a Freundlich model. It was shown that the capacity of adsorption follows the order DCO≫NAL>MPET for all the adsorbents, and among the adsorbents, the external morphology (surface area and mesoporous volume) is the key parameter. The results from thermodynamic analysis show, however, that both morphological and chemical properties of both adsorbates and adsorbents influenced their behavior. Copyright © 2014 Elsevier Ltd. All rights reserved.

Adsorption of Uranyl Ions at the Nano-hydroxyapatite and Its Modification.

PubMed

Skwarek, Ewa; Gładysz-Płaska, Agnieszka; Bolbukh, Yuliia

2017-12-01

Nano-hydroxyapatite and its modification, hydroxyapatite with the excess of phosphorus (P-HAP) and hydroxyapatite with the carbon ions built into the structure (C-HAP), were prepared by the wet method. They were studied by means of XRD, accelerated surface area and porosimetry (ASAP), and SEM. The size of crystallites computed using the Scherrer method was nano-hydroxyapatite (HAP) = 20 nm; P-HAP-impossible to determine; C-HAP = 22 nm; nano-HAP/U(VI) = 13.7 nm; P-HAP/U(VI)-impossible to determine, C-HAP/U(VI) = 11 nm. There were determined basic parameters characterizing the double electrical layer at the nano-HAP/electrolyte and P-HAP/electrolyte, C-HAP/electrolyte inter faces: density of the surface charge and zeta potential. The adsorption properties of nano-HAP sorbent in relation to U(VI) ions were studied by the batch technique. The adsorption processes were rapid in the first 60 min and reached the equilibrium within approximately 120 min (for P-HAP) and 300 min (for C-HAP and nano-HAP). The adsorption process fitted well with the pseudo-second-order kinetics. The Freundlich, Langmuir-Freundlich, and Dubinin-Radushkevich models of isotherms were examined for their ability to the equilibrium sorption data. The maximum adsorption capabilities (q m ) were 7.75 g/g for P-HAP, 1.77 g/g for C-HAP, and 0.8 g/g for HAP at 293 K.

Removal of Heavy Metal Ions with Acid Activated Carbons Derived from Oil Palm and Coconut Shells

PubMed Central

Rahman, Mokhlesur M.; Adil, Mohd; Yusof, Alias M.; Kamaruzzaman, Yunus B.; Ansary, Rezaul H.

2014-01-01

In this work, batch adsorption experiments were carried out to investigate the suitability of prepared acid activated carbons in removing heavy metal ions such as nickel(II), lead(II) and chromium(VI). Acid activated carbons were obtained from oil palm and coconut shells using phosphoric acid under similar activation process while the differences lie either in impregnation condition or in both pretreatment and impregnation conditions. Prepared activated carbons were modified by dispersing hydrated iron oxide. The adsorption equilibrium data for nickel(II) and lead(II) were obtained from adsorption by the prepared and commercial activated carbons. Langmuir and Freundlich models fit the data well. Prepared activated carbons showed higher adsorption capacity for nickel(II) and lead(II). The removal of chromium(VI) was studied by the prepared acid activated, modified and commercial activated carbons at different pH. The isotherms studies reveal that the prepared activated carbon performs better in low concentration region while the commercial ones in the high concentration region. Thus, a complete adsorption is expected in low concentration by the prepared activated carbon. The kinetics data for Ni(II), Pb(II) and Cr(VI) by the best selected activated carbon fitted very well to the pseudo-second-order kinetic model. PMID:28788640

Protein adsorption on electrospun zinc doped hydroxyapatite containing nylon 6 membrane: kinetics and isotherm.

PubMed

Esfahani, Hamid; Prabhakaran, Molamma P; Salahi, Esmaeil; Tayebifard, Ali; Keyanpour-Rad, Mansour; Rahimipour, Mohamad Reza; Ramakrishna, Seeram

2015-04-01

Surface modification of electrospun polymeric membrane surfaces is a critical step towards the separation process including protein adsorption. In this study, the electrospun Nylon fibers was incorporated with positively charged zinc doped hydroxyapatite (HAp) nanoparticles to study the adsorption of negatively charged proteins, namely bovine serum albumin (BSA). Effects of zinc amount within the atomic structure of HAp (nZH; n=0, 4, 8 At.%) was evaluated on produced scaffolds and consequently protein adsorption. The results showed that the ability of Nylon membrane to adsorb BSA increased with incorporation of nZH nanoparticles within the nylon structure. This phenomenon is appeared to be relate to different electrostatic charge and not to physical characteristic of scaffolds. The incorporated membrane (N-4ZH) by nanoparticles with highest zeta (ξ) potential adsorbed the maximum amount of protein. The adsorption of BSA was best fitted with pseudo-second order kinetic model. The experimental isotherm data were further analyzed by using Langmuir and Freundlich equations. By comparing the correlation coefficients obtained for each linear transformation of isotherm analysis, it was found that the Langmuir equation was the best fit equilibrium model that described the adsorption of BSA on these membranes. Copyright © 2014 Elsevier Inc. All rights reserved.

Modification of bamboo-based activated carbon using microwave radiation and its effects on the adsorption of methylene blue

NASA Astrophysics Data System (ADS)

Liu, Qing-Song; Zheng, Tong; Li, Nan; Wang, Peng; Abulikemu, Gulizhaer

2010-03-01

Modification of bamboo-based activated carbon was carried out in a microwave oven under N 2 atmosphere. The virgin and modified activated carbons were characterized by means of low temperature N 2 adsorption, acid-base titration, point of zero charge (pH pzc) measurement, FTIR and XPS spectra. A gradual decrease in the surface acidic groups was observed during the modification, while the surface basicity was enhanced to some extent, which gave rise to an increase in the pH pzc value. The species of the functional groups and relative content of various elements and groups were given further analysis using FTIR and XPS spectra. An increase in the micropores was found at the start, and the micropores were then extended into larger ones, resulting in an increase in the pore volume and average pore size. Adsorption studies showed enhanced adsorption of methylene blue on the modified activated carbons, caused mainly by the enlargement of the micropores. Adsorption isotherm fittings revealed that Langmuir and Freundlich models were applicable for the virgin and modified activated carbons, respectively. Kinetic studies exhibited faster adsorption rate of methylene blue on the modified activated carbons, and the pseudo-second-order model fitted well for all of the activated carbons.

Adsorption of BTEX, MTBE and TAME on natural and modified diatomite.

PubMed

Aivalioti, Maria; Papoulias, Panagiotis; Kousaiti, Athanasia; Gidarakos, Evangelos

2012-03-15

The removal of BTEX (benzene, toluene, ethyl-benzene and m-,p-,o-xylenes), MTBE (methyl tertiary butyl ether) and TAME (tertiary amyl methyl ether) from aqueous solutions by raw, thermally, chemically and both chemically and thermally treated diatomite was studied, through batch adsorption experiments. In total, 14 different diatomite samples were created and tested. Selected physical characteristics of the adsorbents, such as specific surface area and pore volume distribution, were determined. Matrix and competitive adsorption effects were also explored. It was proved that the diatomite samples were effective in removing BTEX, MTBE and TAME from aqueous solutions, with the sample treated with HCl being the most effective, as far as its adsorption capacity and equilibrium time are concerned. Among the contaminants, BTEX appeared to have the strongest affinity, based on mass uptake by the diatomite samples. Matrix effects were proved to be strong, significantly decreasing the adsorption of the contaminants onto diatomite. The kinetics data proved a closer fit to the pseudo second order model, while the isotherm experimental data were a better fit to the Freundlich model. However, the latter produced values of the isotherm constant 1/n greater than one, indicating unfavorable adsorption. Copyright © 2011 Elsevier B.V. All rights reserved.

[Comparison study on adsorption of middle molecular substances with multiwalled carbon nanotubes and activated carbon].

PubMed

Li, Guifeng; Wan, Jianxin; Huang, Xiangqian; Zeng, Qiao; Tang, Jing

2011-08-01

In recent years, multi-walled carbon nanotubes (MWCTs) are very favorable to the adsorption of middle molecular substances in the hemoperfusion because of their multiporous structure, large surface area and high reactivity, which are beneficial to the excellent absorption properties. The purpose of this study was to study the MWCTs on the adsorption capacity of the middle molecular substances. Vitamin B12 (VB12) was selected as a model of the middle molecular substances. The morphologies of MWCTs and activated carbon from commercial "carbon kidney" were observed with scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The adsorption behavior of VB12 was compared to each other with UV-visible absorption spectra. The MWCTs formed a sophistaicate gap structure, and compared to the activated carbon, MWCTs had a larger surface area. By Langmuir equation and Freundlich equation fitting analysis, VB12 adsorption on MWCTs is fit for multi-molecular layer adsorption, and the adsorption type of activated carbon is more inclined to the model corresponding to Langmuir monolayer adsorption. The adsorption rate of MWCTs is faster than that of the activated carbon and the adsorption capacity is greater, which could be expected to become the new adsorbent in the hemoperfusion.

Nylon 6 electrospun nanofibers mat as effective sorbent for the removal of estrogens: kinetic and thermodynamic studies

PubMed Central

2014-01-01

Nylon 6 electrospun nanofibers mat was prepared via electrospinning for the removal of three estrogens, namely, diethylstilbestrol (DES), dienestrol (DS), and hexestrol (HEX) from aqueous solution. Static adsorption as well as the dynamic adsorption was evaluated by means of batch and dynamic disk flow mode, respectively. The kinetic study indicated that the adsorption of the target compounds could be well fitted by the pseudo-second-order equation, suggesting the intra-particle/membrane diffusion process as the rate-limiting step of the adsorption process. The adsorption equilibrium data were all fitted well to the Freundlich isotherm models, with a maximum adsorption capacity values in the range of 97.71 to 208.95 mg/g, which can be compared to or moderately higher than other sorbents published in the literatures. The dynamic disk mode studies indicated that the mean removal yields of three model estrogens were over 95% with a notable smaller amount of adsorbent (4 mg). Thermodynamic study revealed that the adsorption process was exothermic and spontaneous in nature. Desorption results showed that the adsorption capacity can remain up to 80% after seven times usage. It was suggested that Nylon 6 electrospun nanofibers mat has great potential as a novel effective sorbent material for estrogens removal. PMID:25114645

Influence of humic acids on the adsorption of Basic Yellow 28 dye onto an iron organo-inorgano pillared clay and two hydrous ferric oxides.

PubMed

Zermane, Faiza; Cheknane, Benamar; Basly, Jean Philippe; Bouras, Omar; Baudu, Michel

2013-04-01

Effect of humic acids (HAs), macromolecules from natural organic matter, on the adsorption of Basic Yellow 28 is the aim of the present work. Three adsorbents were investigated in this study: an iron organo-inorgano pillared clay and two synthetic Hydrous Iron Oxide (Goethite and HFO). The surface charge was positive in the pH range of this study for the pillared clay; in contrast, it changes from positive to negative when the pH value increased (pH>9) for the two (oxy)hydroxides. Pseudo-first order kinetic rate constants and adsorption capacities increase from humic acid to BY 28. Adsorption isotherms of BY 28 and HA in single component were analysed using the Freundlich equation. Adsorption capacities increased sharply when the pH value of the dye solution was raised from 3 to 9. Increasing the pH medium from 3 to 9 reduces the HA adsorption capacities onto Fe-SMPM and iron oxyhydroxides, respectively. Fitting between measured and predicted sorption capacities of BY 28 and HA in a binary component system indicates that the Sheindorf-Rebuhn-Sheintuch (SRS) model, an extended Freundlich model, is able to describe the simultaneous adsorption of BY 28 and HA. Humic acids favourably affect the adsorption of BY 28, and a cooperative mechanism could be suggested. The synergetic effect existing between BY 28 and HA is shown by the interaction coefficients η12, which are generally high and increase with pH. Some phenomena have been advanced to explain this mechanism. Copyright © 2012 Elsevier Inc. All rights reserved.

A Novel Pb-Resistant Bacillus subtilis Bacterium Isolate for Co-Biosorption of Hazardous Sb(III) and Pb(II): Thermodynamics and Application Strategy

PubMed Central

Cai, Yue; Liu, Dongying; Xu, Changlin; Ai, Yuwei; Sun, Xuemeng; Zhang, Meng; Gao, Yu; Zhang, Yuchao; Yang, Tao; Wang, Jingzhi; Wang, Lijun; Li, Xiaoyun; Yu, Hongtao

2018-01-01

The present work is the first to study co-biosorption of Pb(II) and Sb(III) by a novel bacterium and its application strategy. The biosorption characteristics of Pb(II) and Sb(III) ions from aqueous solution using B. subtilis were investigated. Optimum pH, biomass dosage, contact time and temperature were determined to be 5.00, 6.00 mg/L, 45 min and 35 °C, respectively. Langmuir, Freundlich, Temkin and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the metal ions by B. subtilis. Results showed that Langmuir model fitted the equilibrium data of Pb(II) better than others, while biosorption of Sb(III) obeyed the Freundlich model well. The biosorption capacity of B. subtilis biomass for Pb(II) and Sb(III) ions was found to be 17.34 ± 0.14 and 2.32 ± 0.30 mg/g, respectively. Kinetic data showed the biosorption process of Pb(II) and Sb(III) ions both followed the pseudo-second-order kinetic model, with R2 ranging from 0.974 to 0.999 for Pb(II) and from 0.967 to 0.979 for Sb(III). The calculated thermodynamic parameters, negative ∆G and positive ∆H and ∆S values, indicated the biosorption of Pb(II) and Sb(III) ions onto B. subtilis biomass in water was feasible, endothermic, and spontaneous. Bacterial bioleaching experiment revealed B. subtilis can increase the mobility of Pb(II) and Sb(III) in polluted soil when pH was close to 6 at low temperature. Consequently, B. subtilis, as a cheap and original bacterial material, could be a promising biomass to remove Pb or isolate Sb from industrial wastewater and to assist phytoremediation of Pb and Sb from weak acid or near neutral pH polluted soils at low temperature. PMID:29642529

A Novel Pb-Resistant Bacillus subtilis Bacterium Isolate for Co-Biosorption of Hazardous Sb(III) and Pb(II): Thermodynamics and Application Strategy.

PubMed

Cai, Yue; Li, Xiaoping; Liu, Dongying; Xu, Changlin; Ai, Yuwei; Sun, Xuemeng; Zhang, Meng; Gao, Yu; Zhang, Yuchao; Yang, Tao; Wang, Jingzhi; Wang, Lijun; Li, Xiaoyun; Yu, Hongtao

2018-04-09

The present work is the first to study co-biosorption of Pb(II) and Sb(III) by a novel bacterium and its application strategy. The biosorption characteristics of Pb(II) and Sb(III) ions from aqueous solution using B. subtilis were investigated. Optimum pH, biomass dosage, contact time and temperature were determined to be 5.00, 6.00 mg/L, 45 min and 35 °C, respectively. Langmuir, Freundlich, Temkin and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of the metal ions by B. subtilis . Results showed that Langmuir model fitted the equilibrium data of Pb(II) better than others, while biosorption of Sb(III) obeyed the Freundlich model well. The biosorption capacity of B. subtilis biomass for Pb(II) and Sb(III) ions was found to be 17.34 ± 0.14 and 2.32 ± 0.30 mg/g, respectively. Kinetic data showed the biosorption process of Pb(II) and Sb(III) ions both followed the pseudo-second-order kinetic model, with R² ranging from 0.974 to 0.999 for Pb(II) and from 0.967 to 0.979 for Sb(III). The calculated thermodynamic parameters, negative ∆ G and positive ∆ H and ∆ S values, indicated the biosorption of Pb(II) and Sb(III) ions onto B. subtilis biomass in water was feasible, endothermic, and spontaneous. Bacterial bioleaching experiment revealed B. subtilis can increase the mobility of Pb(II) and Sb(III) in polluted soil when pH was close to 6 at low temperature. Consequently, B. subtilis , as a cheap and original bacterial material, could be a promising biomass to remove Pb or isolate Sb from industrial wastewater and to assist phytoremediation of Pb and Sb from weak acid or near neutral pH polluted soils at low temperature.

Removal of three nitrophenols from aqueous solutions by adsorption onto char ash: equilibrium and kinetic modeling

NASA Astrophysics Data System (ADS)

Magdy, Yehia M.; Altaher, Hossam; ElQada, E.

2018-03-01

In this research, the removal of 2,4 dinitrophenol, 2 nitrophenol and 4 nitrophenol from aqueous solution using char ash from animal bones was investigated using batch technique. Three 2-parameter isotherms (Freundlich, Langmuir, and Temkin) were applied to analyze the experimental data. Both linear and nonlinear regression analyses were performed for these models to estimate the isotherm parameters. Three 3-parameter isotherms (Redlich-Peterson, Sips, Toth) were also tested. Moreover, the kinetic data were tested using pseudo-first order, pseudo-second order, Elovich, Intraparticle diffusion and Boyd methods. Langmuir adsorption isotherm provided the best fit for the experimental data indicating monolayer adsorption. The maximum adsorption capacity was 8.624, 7.55, 7.384 mg/g for 2 nitrophenol, 2,4 dinitrophenol, and 4 nitrophenol, respectively. The experimental data fitted well to pseudo-second order model suggested a chemical nature of the adsorption process. The R 2 values for this model were 0.973 up to 0.999. This result with supported by the Temkin model indicating heat of adsorption to be greater than 10 kJ/mol. The rate controlling step was intraparticle diffusion for 2 nitrophenol, and a combination of intraparticle diffusion and film diffusion for the other two phenols. The pH and temperature of solution were found to have a considerable effect, and the temperature indicated the exothermic nature of the adsorption process. The highest adsorption capacity was obtained at pH 9 and 25 °C.

[Adsorption of a dye by sludges and the roles of extracellular polymeric substances].

PubMed

Kong, Wang-sheng; Liu, Yan

2007-12-01

This paper investigated the adsorption of a dye, acid turquoise blue A, by four kinds of sludges including activated sludge, anaerobic sludge, dried activated sludge, and dried anaerobic sludge, respectively. The roles of extracellular polymeric substances (EPS) including the soluble EPS (SEPS) and bound EPS (BEPS) for the biosorption of activated sludge and anaerobic sludge were further studied. Results show that the relation between four kinds of sludge adsorption amount and remained concentration of the dye fitted well both Freundlich model (R2: 0.921-0.995) and Langmuir model (R2: 0.958-0.993), but not quite fitted BET model (R2: 0.07-0.863). The adsorption capability of dried anaerobic sludge ranked the highest, and dried activated sludge was the lowest. According to Langmuir isotherm, the maximum adsorption amount of dried anaerobic, anaerobic, activated, and dried activated sludge was 104 mg/g, 86 mg/g, 65 mg/g, 20 mg/g, respectively. The amount of the dye found in EPS for both activated sludge and anaerobic sludge were over 50%, illustrating that EPS adsorption was predominant in adsorption of the dye by sludge. The amount of adsorbed dye by BEPS was greater than that by SEPS for anaerobic sludge, but for activated sludge the result was quite opposite. The amount of adsorbed dye by unit mass SEPS was much higher than the corresponding values of BEPS for both sludges. The average amount of adsorbed dye by unit mass SEPS was 52 times of the corresponding value of BEPS for activated sludge, and 10 times for anaerobic sludge. The relation between adsorption amount of dye by BEPS from anaerobic sludge and remained concentration of the dye in mixed liquor was best fitted to Langmuir model (R2: 0.9986).

2,4-Dinitrophenylhydrazine functionalized sodium dodecyl sulfate-coated magnetite nanoparticles for effective removal of Cd(II) and Ni(II) ions from water samples.

PubMed

Sobhanardakani, Soheil; Zandipak, Raziyeh

2015-07-01

2,4-Dinitrophenylhydrazine immobilized on sodium dodecyl sulfate (SDS)-coated magnetite and was used for removal of Cd(II) and Ni(II) ions from aqueous solution. The prepared product was characterized by X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy (FT-IR), and scanning electron microscopy (SEM). The size of the nanoparticles according to SEM was obtained around 20-35 nm. In batch tests, the effects of pH, contact time, initial metal concentration, and temperature were studied. The kinetic and equilibrium data were modeled with recently developed models. The adsorption kinetics and isotherms were well fitted by the fractal-like pseudo-second-order model and Langmuir-Freundlich model, respectively. Maximum adsorption capacity by this adsorbent is 255.1 mg g(-1) for Cd(II) ion and 319.6 mg g(-1) for Ni(II) ion at pH 7.0 and 25 °C. The method was successfully applied to the removal of metal cations in real samples (tap water, river water, and petrochemical wastewater).

Biosorption of lead (II) ions by NaOH-activated apple (Malus domestica) juice residue

NASA Astrophysics Data System (ADS)

Arimurti, Devita Dwi; Heraldy, Eddy; Lestari, Witri Wahyu

2016-02-01

This research studied the removal of Pb(II) ions from aqueous solutions using NaOH-activated apple (Malus domestica) juice residue. Biosorbent was characterized with Fourier Transform Infrared Spectrophotometer (FTIR), and Surface Area Analyzer (SAA). The effects of biosorbent dosage, pH, contact time and initial metal ion concentration had been investigated in batch-adsorption method. The biosorption kinetic data were analyzed by pseudo-first-order and pseudo-second-order kinetics model. Freundlich and Langmuir's isotherm were used to describe the biosorption process. The optimum conditions of Pb(II) adsorption was observed at 60 min of contact time, pH 4, and 0.1 g biosorbent dosage in 25 ml solution. The biosorption kinetics followed the pseudo-second-order kinetic model, resulted biosorption constant rate of 0.184 g.mg-1.min-1. The Langmuir isotherm model exhibited the best fit to experimental data. The maximum biosorption capacity of Pb(II) determined according to the Langmuir model was 90.90 mg.g-1 at 302 K, with the adsorption energy of 26.429 kJ.mol-1.

Adsorption of the compounds encountered in monosaccharide dehydration in zeolite beta.

PubMed

León, Marta; Swift, T Dallas; Nikolakis, Vladimiros; Vlachos, Dionisios G

2013-06-04

A comprehensive study of the adsorption of the compounds involved in the reaction of dehydration of fructose to 5-hydroxymethyl furfural (HMF) on the zeolite H-BEA with SiO2/Al2O3 = 18 has been carried out. Furthermore, a method for the estimation of the real adsorption loading from the experimentally measured excess adsorption is developed and applied to calculate the adsorption isotherms both in the case of single-solute and multisolute mixtures. It was found that zeolite H-BEA adsorbs HMF and levulinic acid from water mixtures to greater extent than sugars and formic acid, which prefer to partition in the aqueous phase. HMF and levulinic acid adsorption isotherms could be fitted in a Redlich-Peterson isotherm model, while the adsorption of formic acid is better fitted using the Freundlich model and sugars via the Henry model. Adsorption loadings decreased with increasing temperature (0, 25, and 40 °C), which is characteristic of an exothermic process. From the temperature dependence of the isotherms, the limiting heat of adsorption at zero coverage was determined using van't Hoff equation. Given the importance and the complexity of multicomponent systems, several experiments of adsorption of multisolute solutions have been carried out. In most of the cases, the ideal adsorbed solution theory (IAST) has been proven to satisfactorily predict adsorption from multisolute mixtures using as input the single-solute isotherms.

Sorption of dodecyltrimethylammonium chloride (DTAC) to agricultural soils.

PubMed

Xiang, Lei; Sun, Teng-Fei; Zheng, Mei-Jie; Li, Yan-Wen; Li, Hui; Wong, Ming-Hung; Cai, Quan-Ying; Mo, Ce-Hui

2016-08-01

Quaternary ammonium compounds (QACs) used as cationic surfactants are intensively released into environment to be pollutants receiving more and more concerns. Sorption of dodecyltrimethylammonium chloride (DTAC), one of commonly used alkyl QACs, to five types of agricultural soils at low concentrations (1-50mg/L) was investigated using batch experiments. DTAC sorption followed pseudo-second-order kinetics and reached reaction equilibrium within 120min. Both Freundlich model and Langmuir model fitted well with DTAC isotherm data with the latter better. DTAC sorption was spontaneous and favorable, presenting a physical sorption dominated by ion exchanges. Sorption distribution coefficient and sorption affinity demonstrated that soil clay contents acted as a predominant phase of DTAC sorption. DTAC could display a higher mobility and potential accumulation in crops in the soils with lower clay contents and lower pH values. Sorption of DTAC was heavily affected by ions in solution with anion promotion and cation inhibition. Copyright © 2016. Published by Elsevier B.V.

A study of the kinetics and isotherms for Cr(VI) adsorption in a binary mixture of Cr(VI)-Ni(II) using hierarchical porous carbon obtained from pig bone.

PubMed

Li, Chengxian; Huang, Zhe; Huang, Bicheng; Liu, Changfeng; Li, Chengming; Huang, Yaqin

2014-01-01

Cr(VI) adsorption in a binary mixture Cr(VI)-Ni(II) using the hierarchical porous carbon prepared from pig bone (HPC) was investigated. The various factors affecting adsorption of Cr(VI) ions from aqueous solutions such as initial concentration, pH, temperature and contact time were analyzed. The results showed excellent efficiency of Cr(VI) adsorption by HPC. The kinetics and isotherms for Cr(VI) adsorption from a binary mixture Cr(VI)-Ni(II) by HPC were studied. The adsorption equilibrium described by the Langmuir isotherm model is better than that described by the Freundlich isotherm model for the binary mixture in this study. The maximum adsorption capacity was reliably found to be as high as 192.68 mg/g in the binary mixture at pH 2. On fitting the experimental data to both pseudo-first- and second-order equations, the regression analysis of the second-order equation gave a better R² value.

The Efficient Removal of Heavy Metal Ions from Industry Effluents Using Waste Biomass as Low-Cost Adsorbent: Thermodynamic and Kinetic Models

NASA Astrophysics Data System (ADS)

Indhumathi, Ponnuswamy; Sathiyaraj, Subbaiyan; Koelmel, Jeremy P.; Shoba, Srinivasan U.; Jayabalakrishnan, Chinnasamy; Saravanabhavan, Munusamy

2018-05-01

The ability of green micro algae Chlorella vulgaris for biosorption of Cu(II) ions from an aqueous solution was studied. The biosorption process was affected by the solution pH, contact time, temperature and initial Cu(II) concentration. Experimental data were analyzed in terms of pseudo-first order, pseudo-second order and intra particle diffusion models. Results showed that the sorption process of Cu(II) ions followed pseudo-second order kinetics. The sorption data of Cu(II) ions are fitted to Langmuir, Freundlich, and Redlich-Peterson isotherms, and the Temkin isotherm. The thermodynamic study shows the Cu(II) biosorption was exothermic in nature. The Cu(II) ions were recovered effectively from Chlorella vulgaris biomass using 0.1 M H2SO4 with up to 90.3% recovery, allowing for recycling of the Cu. Green algae from freshwater bodies showed significant potential for Cu(II) removal and recovery from industrial wastewater.

Adsorption of Pb(II) ions onto biomass from Trifolium resupinatum: equilibrium and kinetic studies

NASA Astrophysics Data System (ADS)

Athar, Makshoof; Farooq, Umar; Aslam, Muhammad; Salman, M.

2013-09-01

The present study provides information about the binding of Pb(II) ions on an eco-friendly and easily available biodegradable biomass Trifolium resupinatum. The powdered biomass was characterized by FTIR, potentiometric titration and surface area analyses. The FTIR spectrum showed the presence of hydroxyl, carbonyl and amino functional groups and Pb(II) ions bound with the oxygen- and nitrogen-containing sites (hydroxyl and amino groups). The acidic groups were also confirmed by titrations. Effects of various environmental parameters (time, pH and concentration) have been studied. The biosorption process achieved equilibrium in a very short period of time (25 min). Non-linear approach for Langmuir and Freundlich models was used to study equilibrium process and root mean-square error was used as an indicator to decide the fitness of the mathematical model. The biosorption process was found to follow pseudo-second-order kinetics and was very fast. Thus, the biomass can be cost-effectively used for the binding of Pb(II) ions from aqueous solutions.

Iron oxide impregnated Morus alba L. fruit peel for biosorption of Co(II): biosorption properties and mechanism.

PubMed

Koduru, Janardhan Reddy; Chang, Yoon-Young; Yang, Jae-Kyu; Kim, Im-Soon

2013-01-01

Biosorption is an ecofriendly wastewater treatment technique with high efficiency and low operating cost involving simple process for the removal of heavy metal ions from aqueous solution. In the present investigation, Morus alba L. fruit peel powder (MAFP) and iron oxide impregnated Morus alba L. fruit peel powder (IO-MAFP) were prepared and used for treating Co(II) contaminated aqueous solutions. Further the materials were characterized by using FTIR and SEM-EDX analysis. From FT-IR analysis it was found that hydroxyl, methoxy, and carbonyl groups are responsible for Co(II) biosorption. The kinetic data obtained for both biosorbents was well fitted with pseudo-second-order kinetic model. The equilibrium data was in tune with the Langmuir and Freundlich isotherm models. The thermodynamic studies were also carried and it was observed that sorption process was endothermic at 298-328 K. These studies demonstrated that both biosorbents were promising, efficient, economic, and biodegradable sorbents.

Experimental binding of lead to a low cost on biosorbent: Nopal (Opuntia streptacantha).

PubMed

Miretzky, Patricia; Muñoz, Carolina; Carrillo-Chávez, Alejandro

2008-03-01

The use of nopal cladodes (Opuntia streptacantha) as raw material for Pb(2+) biosorption was investigated. Batch experiments were carried out to determine Pb(2+) sorption capacity and the efficiency of the sorption process under different pH, initial Pb(2+) and nopal biomass concentrations. The experimental data showed a good fit to Langmuir and Freundlich isotherms models. The maximum adsorption capacity for Pb(2+) was 0.14 mmol g(-1) with an efficiency higher than 94% (pH 5.0 and 2.5 g L(-1) nopal biomass). The Pb(2+) kinetics were best described by the pseudo-second-order rate model. The rate constant, the initial sorption rate and the equilibrium sorption capacity were determined. The practical implication of this study is the development of an effective and economic technology in which the nopal biomass did not undergo any chemical or physical pretreatment, which added to nopal abundance in Mexico and its low cost makes it a good option for Pb(2+) removal from contaminated waters.

Development of a process for separation of mogroside V from Siraitia grosvenorii by macroporous resins.

PubMed

Zhang, Min; Yang, Huihua; Zhang, Hongyang; Wang, Yuerong; Hu, Ping

2011-08-25

A separation method was developed for the preparative separation and enrichment of the non-caloric sweetener mogroside V from Siraitia grosvenorii. The adsorption properties of six macroporous resins were evaluated. Results showed that HZ 806 resin offered the best adsorption and desorption capacities. Based on the adsorption experiments on HZ 806, the adsorption data were found to fit the Freundlich model well. The pseudo-second-order kinetic model showed the highest correlation with the experimental results. Separation was performed with deionized water and 40% aqueous ethanol solution as mobile phases. In a typical run, 100 g of herb was processed and 3.38 g of mogroside V with a purity of 10.7% was harvested. This separation method provided a 15.1-fold increase in the purification factor from 0.5% to 10.7%. The present study showed that HZ 806 resins were effective for the separation and enrichment of mogroside V from S. grosvenorii.

Fe-FeS2 adsorbent prepared with iron powder and pyrite by facile ball milling and its application for arsenic removal.

PubMed

Min, Xiaobo; Li, Yangwenjun; Ke, Yong; Shi, Meiqing; Chai, Liyuan; Xue, Ke

2017-07-01

Arsenic is one of the major pollutants and a worldwide concern because of its toxicity and chronic effects on human health. An adsorbent of Fe-FeS 2 mixture for effective arsenic removal was successfully prepared by mechanical ball milling. The products before and after arsenic adsorption were characterized with scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The adsorbent shows high arsenic removal efficiency when molar ratio of iron to pyrite is 5:5. The experimental data of As(III) adsorption are fitted well with the Langmuir isotherm model with a maximal adsorption capacity of 101.123 mg/g. And As(V) data were described perfectly by the Freundlich model with a maximal adsorption capacity of 58.341 L/mg. As(III) is partial oxidized to As(V) during the adsorption process. High arsenic uptake capability and cost-effectiveness of waste make it potentially attractive for arsenic removal.

Separation of acid blue 25 from aqueous solution using water lettuce and agro-wastes by batch adsorption studies

NASA Astrophysics Data System (ADS)

Kooh, Muhammad Raziq Rahimi; Dahri, Muhammad Khairud; Lim, Linda B. L.; Lim, Lee Hoon; Chan, Chin Mei

2018-05-01

Three plant-based materials, namely water lettuce (WL), tarap peel (TP) and cempedak peel (CP), were used to investigate their potentials as adsorbents using acid blue 25 (AB25) dye as a model for acidic dye. The adsorbents were characterised using Fourier transform infrared spectroscopy, X-ray fluorescence and scanning electron microscope. Batch experiments involving parameters such as pH, temperature, contact time, and initial dye concentration were done to investigate the optimal conditions for the adsorption of AB25 onto the adsorbents. Thermodynamics study showed that the uptake of AB25 by the three adsorbents was feasible and endothermic in nature. Both the Langmuir and Freundlich isotherm models can be used to describe the adsorption process of AB25 onto WL and CP while pseudo-second-order fitted the kinetics data, suggesting that chemisorptions were majorly involved. The use of 0.1 M of NaOH showed the best results in regenerating of the WL, TP and CP's adsorption ability after AB25 treatment.

Iron Oxide Impregnated Morus alba L. Fruit Peel for Biosorption of Co(II): Biosorption Properties and Mechanism

PubMed Central

Koduru, Janardhan Reddy; Chang, Yoon-Young; Yang, Jae-Kyu; Kim, Im-Soon

2013-01-01

Biosorption is an ecofriendly wastewater treatment technique with high efficiency and low operating cost involving simple process for the removal of heavy metal ions from aqueous solution. In the present investigation, Morus alba L. fruit peel powder (MAFP) and iron oxide impregnated Morus alba L. fruit peel powder (IO-MAFP) were prepared and used for treating Co(II) contaminated aqueous solutions. Further the materials were characterized by using FTIR and SEM-EDX analysis. From FT-IR analysis it was found that hydroxyl, methoxy, and carbonyl groups are responsible for Co(II) biosorption. The kinetic data obtained for both biosorbents was well fitted with pseudo-second-order kinetic model. The equilibrium data was in tune with the Langmuir and Freundlich isotherm models. The thermodynamic studies were also carried and it was observed that sorption process was endothermic at 298–328 K. These studies demonstrated that both biosorbents were promising, efficient, economic, and biodegradable sorbents. PMID:24324384

Removal of Heavy Metals by Adsorption onto Activated Carbon Derived from Pine Cones of Pinus roxburghii.

PubMed

Saif, Muhammad Jawwad; Zia, Khalid Mahmood; Fazal-ur-Rehman; Usman, Muhammad; Hussain, Abdullah Ijaz; Chatha, Shahzad Ali Shahid

2015-04-01

Activated carbon derived from cones of Pinus roxburghii (Himalayan Pine) was used as an adsorbent for the removal of copper, nickel and chromium ions from waste water. Surface analysis was carried out to determine the specific surface area and pore size distribution of the pine cone derived activated carbon. Optimal parameters, effect of adsorbent quantity, pH, equilibrium time, agitation speed and temperature were studied. Equilibrium data were evaluated by Langmuir and Freundlich isotherm models. Langmuir isotherm afforded the best fit to the equilibrium data with a maximum adsorption capacity of 14.2, 31.4 and 29.6 mg/g for Cu(II), Ni(II) and Cr(VI) respectively. Maximum adsorption of Cu(II), Ni(II) was observed in the pH range 4.0 to 4.5, whereas the best adsorption of Cr(VI) was observed at pH 2.5. It was found that 180 minutes was sufficient to gain adsorption equilibrium. The adsorption process follows a pseudo-second-order kinetic model.

Synthesis of magnetic ordered mesoporous carbon (Fe-OMC) adsorbent and its evaluation for fuel desulfurization

NASA Astrophysics Data System (ADS)

Farzin Nejad, N.; Shams, E.; Amini, M. K.

2015-09-01

In this work, magnetic ordered mesoporous carbon adsorbent was synthesized using soft templating method to adsorb sulfur from model oil (dibenzothiophene in n-hexane). Through this research, pluronic F-127, resorcinol-formaldehyde and hydrated iron nitrate were respectively used as soft template, carbon source and iron source. The adsorbent was characterized by X-ray diffraction, nitrogen adsorption-desorption isotherm and transmission electron microscopy. Nitrogen adsorption-desorption measurement revealed the high surface area (810 m2 g-1), maxima pore size of 3.3 nm and large pore volume (1.01 cm3 g-1) of the synthesized sample. The adsorbent showed a maximum adsorption capacity of 111 mg dibenzothiophene g-1 of adsorbent. Sorption process was described by the pseudo-second-order rate equation and could be better fitted by the Freundlich model, showing the heterogeneous feature of the adsorption process. In addition, the adsorption capacity of regenerated adsorbent was 78.6% of the initial level, after five regeneration cycles.

Toxic metals biosorption by Jatropha curcas deoiled cake: equilibrium and kinetic studies.

PubMed

Rawat, Anand P; Rawat, Monica; Rai, J P N

2013-08-01

The equilibrium sorption of Cr(VI) and Cu(II) from aqueous solution using Jatropha curcas deoiled cake, has been studied with respect to adsorbent dosage, contact time, pH, and initial metal concentration in batch mode experiments. Removal of Cu(II) by deoiled cake was greater than that of Cr(VI). The adsorbent chemical characteristics, studied by Fourier transform-infrared analysis, suggested that the presence of Cr(VI) and Cu(II) in the biomass influenced the bands corresponding to hydroxyl and carboxyl groups. Desorption studies revealed that maximum metals recovery was achieved by HNO3 followed by CH3COOH and HCl. The Freundlich isotherm model showed good fit to the equilibrium adsorption data. The adsorption kinetics followed the pseudo-second-order model, which provided the best correlation for the biosorption process, and suggested that J. curcas deoiled cake can be used as an efficient biosorbent over other commonly used sorbents for decontamination of Cr(VI)- and Cu(II)-containing wastewater.

Adsorption of organophosphorus pesticides in tropical soils: The case of karst landscape of northwestern Yucatan.

PubMed

Alfonso, Lorenzo-Flores; Germán, Giácoman Vallejos; María Del Carmen, Ponce Caballero; Hossein, Ghoveisi

2017-01-01

This article discusses the adsorption of four organophosphorus pesticides-diazinon, dimethoate, methyl parathion, and sulfotep-in soil samples from four sites-Komchén, Xcanatún, Chablekal and Mocochá- in the northwest of Yucatan, Mexico. These pesticides have been detected in groundwater at concentrations greater than 5 (μg/L) during recent monitoring campaigns in the study area. In this region, groundwater contamination is exacerbated by its karst aquifer, which is susceptible to contamination and is considered very vulnerable. The experimental work was carried out using the batch equilibrium technique. Pesticide analyses by solid-phase extraction and gas chromatography were performed. The equilibrium adsorption data were analyzed by Henry, Langmuir and Freundlich models. The results indicate that the Freundlich model provides the best correlation of the experimental data. Freundlich adsorption coefficients K f were in the range of 1.62-2.35 for sulfotep, 2.43 to 3.25 for dimethoate, from 5.54 to 9.27 for methyl parathion, and 3.22 to 5.17 for diazinon. Freundlich adsorption coefficients were normalized to the content of organic carbon in the soil to estimate the sorption coefficient of organic carbon (K OC ). K OC values were in the range of 9.45-71.80, indicated that four pesticides have low adsorption on the four studied soils, which represents a high risk of contamination to the aquifer. Copyright © 2016 Elsevier Ltd. All rights reserved.

Thermodynamic, Kinetic, and Equilibrium Parameters for the Removal of Lead and Cadmium from Aqueous Solutions with Calcium Alginate Beads

PubMed Central

Alfaro-Cuevas-Villanueva, Ruth; Hidalgo-Vázquez, Aura Roxana; Cortés Penagos, Consuelo de Jesús; Cortés-Martínez, Raúl

2014-01-01

The sorption of cadmium (Cd) and lead (Pb) by calcium alginate beads (CAB) from aqueous solutions in batch systems was investigated. The kinetic and thermodynamic parameters, as well as the sorption capacities of CAB in each system at different temperatures, were evaluated. The rate of sorption for both metals was rapid in the first 10 minutes and reached a maximum in 50 minutes. Sorption kinetic data were fitted to Lagergren, pseudo-second-order and Elovich models and it was found that the second-order kinetic model describes these data for the two metals; comparing kinetic parameters for Cd and Pb sorption a higher kinetic rate (K 2) for Pb was observed, indicating that the interaction between lead cations and alginate beads was faster than for cadmium. Similarly, isotherm data were fitted to different models reported in literature and it was found that the Langmuir-Freundlich (L-F) and Dubinin-Radushkevich (D-R) models describe the isotherms in all cases. CAB sorption capacity for cadmium was 27.4 mg/g and 150.4 mg/g for lead, at 25°C. Sorption capacities of Cd and Pb increase as temperature rises. According to the thermodynamic parameters, the cadmium and lead adsorption process was spontaneous and endothermic. It was also found that pH has an important effect on the adsorption of these metals by CAB, as more were removed at pH values between 6 and 7. PMID:24587740

Preparation of a specific bamboo based activated carbon and its application for ciprofloxacin removal.

PubMed

Wang, Y X; Ngo, H H; Guo, W S

2015-11-15

The studied bamboo based activated carbon (BbAC) with high specific surface area (SSA) and high micro pore volume was prepared from bamboo scraps by the combined activation of H3PO4 and K2CO3. The BbAC was characterized based on the N2 adsorption isotherm at 77K. The results showed that the SSA and pore volume of BbAC increased with increasing impregnation ratio and reached maxima at the impregnation ratio of 3:1 at 750°C. Under these optimal conditions, the BbAC obtained could have a maximum SSA of 2237 m(2)/g and a maximum total pore volume of 1.23 cm(3)/g with the micro pore ratio of more than 90%. The adsorption performance of ciprofloxacin (CIP) on the BbAC was determined at 298 K. The Langmuir and Freundlich models were employed to describe the adsorption equilibrium and the kinetic data were fitted by pseudo first-order and pseudo second-order kinetic models. The results showed that the Langmuir model and the pseudo second-order kinetic model presented better fittings for the adsorption equilibrium and kinetics data, respectively. The maximum adsorption amount of CIP (613 mg/g) on the BbAC was much higher than the report in the literature. Conclusively, the BbAC could be a promising adsorption material for CIP removal from water. Copyright © 2015 Elsevier B.V. All rights reserved.

Investigate the ultrasound energy assisted adsorption mechanism of nickel(II) ions onto modified magnetic cobalt ferrite nanoparticles: Multivariate optimization.

PubMed

Mehrabi, Fatemeh; Alipanahpour Dil, Ebrahim

2017-07-01

In present study, magnetic cobalt ferrite nanoparticles modified with (E)-N-(2-nitrobenzylidene)-2-(2-(2-nitrophenyl)imidazolidine-1-yl) ethaneamine (CoFe 2 O 4 -NPs-NBNPIEA) was synthesized and applied as novel adsorbent for ultrasound energy assisted adsorption of nickel(II) ions (Ni 2+ ) from aqueous solution. The prepared adsorbent characterized by Fourier transforms infrared spectroscopy (FT-IR), transmission electron microscope (TEM), vibrating sample magnetometer (VSM) and X-ray diffraction (XRD). The dependency of adsorption percentage to variables such as pH, initial Ni 2+ ions concentration, adsorbent mass and ultrasound time were studied with response surface methodology (RSM) by considering the desirable functions. The quadratic model between the dependent and independent variables was built. The proposed method showed good agreement between the experimental data and predictive value, and it has been successfully employed to adsorption of Ni 2+ ions from aqueous solution. Subsequently, the experimental equilibrium data at different concentration of Ni 2+ ions and 10mg amount of adsorbent mass was fitted to conventional isotherm models like Langmuir, Freundlich, Tempkin, Dubinin-Radushkevich and it was revealed that the Langmuir is best model for explanation of behavior of experimental data. In addition, conventional kinetic models such as pseudo-first and second-order, Elovich and intraparticle diffusion were applied and it was seen that pseudo-second-order equation is suitable to fit the experimental data. Copyright © 2016 Elsevier B.V. All rights reserved.

Equilibrium, kinetics and mechanism of Au3+, Pd2+ and Ag+ ions adsorption from aqueous solutions by graphene oxide functionalized persimmon tannin.

PubMed

Wang, Zhongmin; Li, Xiaojuan; Liang, Haijun; Ning, Jingliang; Zhou, Zhide; Li, Guiyin

2017-10-01

In this study, a novel bio-adsorbent (PT-GO) was prepared by functionalization persimmon tannin (PT) with graphene oxide (GO) and the effective adsorption behaviors of Au 3+ , Pd 2+ and Ag + ions from aqueous solution was investigated. The PT-GO was characterized by Fourier transform infrared spectrometer (FTIR), scanning electronic microscope (SEM), thermogravimetric analysis (TGA) and Zeta potential. Many influence factors such as pH value, bio-adsorbent dosage, initial concentration of metal ions and contact time were optimized. The maximum adsorption capacity for Au 3+ , Pd 2+ and Ag + was 1325.09mg/g, 797.66mg/g and 421.01mg/g, respectively. The equilibrium isotherm for the adsorption of Au 3+ and Ag + on PT-GO were found to obey the Langmuir model, while the Freundlich model fitted better for Pd 2+ . The adsorption process of Au 3+ , Pd 2+ presented relatively fast adsorption kinetics with pseudo-second-order equation as the best fitting model, while the pseudo-first-order kinetic model was suitable for describing the adsorption of Ag + . Combination of ion exchange, electrostatic interaction and physical adsorption was the mechanism for adsorption of Au 3+ , Pd 2+ and Ag + onto PT-GO bio-adsorbent. Therefore, the PT-GO bio-adsorbent would be an ideal adsorbent for removal of precious metal ions and broaden the potential applications of persimmon tannin in environmental research. Copyright © 2017 Elsevier B.V. All rights reserved.

Prediction of optimum sorption isotherm: comparison of linear and non-linear method.

PubMed

Kumar, K Vasanth; Sivanesan, S

2005-11-11

Equilibrium parameters for Bismarck brown onto rice husk were estimated by linear least square and a trial and error non-linear method using Freundlich, Langmuir and Redlich-Peterson isotherms. A comparison between linear and non-linear method of estimating the isotherm parameters was reported. The best fitting isotherm was Langmuir isotherm and Redlich-Peterson isotherm equation. The results show that non-linear method could be a better way to obtain the parameters. Redlich-Peterson isotherm is a special case of Langmuir isotherm when the Redlich-Peterson isotherm constant g was unity.

Implementation of ferric hydroxide-based media for removal of toxic metalloids

NASA Astrophysics Data System (ADS)

Szlachta, Małgorzata; Wójtowicz, Patryk

2017-11-01

Effective removal of inorganic arsenic species is possible by application of the sorption technique with the use of iron-based sorbents. This study investigates the removal of arsenic(III) and arsenic(V) from an aqueous solution by application of a granular ferric hydroxide-based sorbent. The performance of tested media was evaluated based on the batch and fixed-bed adsorption studies. The efficiency of the process was determined with various treatment times, adsorbent doses, initial concentrations of arsenic and various solution temperatures. The obtained adsorption data were fitted with pseudo-first and second-order kinetic models and Langmuir and Freundlich isotherm equations. It was observed that the overall arsenite removal was lower when compared to the arsenate, and all tested operating parameters influenced the process efficiency. The experiments under dynamic conditions showed high treatment capacity and stability of tested adsorbent over a long period of time.

Adsorption of aromatic compounds from the biodegradation of azo dyes on activated carbon

NASA Astrophysics Data System (ADS)

Faria, P. C. C.; Órfão, J. J. M.; Figueiredo, J. L.; Pereira, M. F. R.

2008-03-01

The adsorption of three selected aromatic compounds (aniline, sulfanilic acid and benzenesulfonic acid) on activated carbons with different surface chemical properties was investigated at different solution pH. A fairly basic commercial activated carbon was modified by means of chemical treatment with HNO 3, yielding an acid activated carbon. The textural properties of this sample were not significantly changed after the oxidation treatment. Equilibrium isotherms of the selected compounds on the mentioned samples were obtained and the results were discussed in relation to their surface chemistry. The influence of electrostatic and dispersive interactions involved in the uptake of the compounds studied was evaluated. The Freundlich model was used to fit the experimental data. Higher uptakes are attained when the compounds are present in their molecular form. In general, adsorption was disfavoured by the introduction of oxygen-containing groups on the surface of the activated carbon.

Characterization of DOM adsorption of CNTs by using excitation-emission matrix fluorescence spectroscopy and multiway analysis.

PubMed

Peng, Mingguo; Li, Huajie; Li, Dongdong; Du, Erdeng; Li, Zhihong

2017-06-01

Carbon nanotubes (CNTs) were utilized to adsorb DOM in micro-polluted water. The characteristics of DOM adsorption on CNTs were investigated based on UV 254 , TOC, and fluorescence spectrum measurements. Based on PARAFAC (parallel factor) analysis, four fluorescent components were extracted, including one protein-like component (C4) and three humic acid-like components (C1, C2, and C3). The adsorption isotherms, kinetics, and thermodynamics of DOM adsorption on CNTs were further investigated. A Freundlich isotherm model fit the adsorption data well with high values of correlation. As a type of macro-porous and meso-porous adsorbent, CNTs preferably adsorb humic acid-like substances rather than protein-like substances. The increasing temperature will speed up the adsorption process. The self-organizing map (SOM) analysis further explains the fluorescent properties of water samples. The results provide a new insight into the adsorption behaviour of DOM fluorescent components on CNTs.

Evaluation of BTEX and phenol removal from aqueous solution by multi-solute adsorption onto smectite organoclay.

PubMed

Carvalho, M N; da Motta, M; Benachour, M; Sales, D C S; Abreu, C A M

2012-11-15

The removal process of BTEX and phenol was evaluated. The smectite organoclay for single-solute system reached removal was evaluated by adsorption on smectite organoclay adsorbent by kinetic and equilibrium efficiencies between 55 and 90% while was reached between 30 and 90% for multi-solute system at 297 K and pH 9. The Langmuir-Freundlich model was used to fit the experimental data with correlation coefficient between 0.98 and 0.99 providing kinetic and equilibrium parameter values. Phenol and ethylbenzene presented high maximum adsorbed amount, 8.28 and 6.67 mg/g, respectively, compared to the other compounds for single-solute. Toluene and p-xylene presented high values of adsorption constant which indicates a high adsorption affinity of compounds to organoclay surface and high binding energy of adsorption. Phenol presented low kinetic adsorption constant value indicating slow rate of adsorption. Copyright © 2012 Elsevier B.V. All rights reserved.

Adsorption of silver nanoparticles from aqueous solution on copper-based metal organic frameworks (HKUST-1).

PubMed

Conde-González, J E; Peña-Méndez, E M; Rybáková, S; Pasán, J; Ruiz-Pérez, C; Havel, J

2016-05-01

Silver nanoparticles (AgNP) are emerging pollutants. The use of novel materials such as Cu-(benzene 1,3,5-tricarboxylate, BTC) Metal-Organic Framework (MOFs), for AgNP adsorption and their removal from aqueous solutions has been studied. The effect of different parameters was followed and isotherm model was suggested. MOFs adsorbed fast and efficiently AgNP in the range C0 < 10 mg L(-1), being Freundlich isotherm (R = 0.993) these data fitted to. Among studied parameters a remarkable effect of chloride on sorption was found, thus their possible interactions were considered. The high adsorption efficiency of AgNP was achieved and it was found to be very fast. The feasibility of adsorption on Cu-(BTC) was proved in spiked waters. The results showed the potential interest of new material as adsorbent for removing AgNP from environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Removal of thallium from aqueous solutions using Fe-Mn binary oxides.

PubMed

Li, Huosheng; Chen, Yongheng; Long, Jianyou; Li, Xiuwan; Jiang, Daqian; Zhang, Ping; Qi, Jianying; Huang, Xuexia; Liu, Juan; Xu, Ruibing; Gong, Jian

2017-09-15

In this study, Fe-Mn binary oxides, which harbor the strong oxidative power of manganese dioxide and the high adsorption capacity of iron oxides, were synthesized for Tl(I) removal using a concurrent chemical oxidation and precipitation method. The adsorption of Tl onto the Fe-Mn adsorbent was fast, effective, and selective, with equilibrium sorption reaching over 95% under a broad operating pH (3-12), and high ionic strength (0.1-0.5mol/L). The adsorption can be well fitted with both Langmuir and Freundlich isotherms, and the kinetics can be well described by the pseudo-second-order model. Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS) spectra suggest that surface complexation, oxidation and precipitation were the main mechanisms for the removal of Tl. This study shows that the Fe-Mn binary oxides could be a promising adsorbent for Tl removal. Copyright © 2017 Elsevier B.V. All rights reserved.

Adsorption of Arsenic on Multiwall Carbon Nanotube–Zirconia Nanohybrid for Potential Drinking Water Purification

PubMed Central

AddoNtim, Susana; Mitra, Somenath

2012-01-01

The adsorptive removal of arsenic from water using a multiwall carbon nanotube-zirconia nanohybrid (MWCNT-ZrO2) is presented. The MWCNT-ZrO2 with 4.85% zirconia was effective in meeting the drinking water standard levels of 10 μg L−1. The absorption capacity of the composite were 2000 μg g−1 and 5000 μg g−1 for As (III) and As (V) respectively, which were significantly higher than those reported previously for iron oxide coated MWCNTs. The adsorption of As (V) on MWCNT-ZrO2 was faster than that of As (III), and a pseudo-second order rate equation effectively described the uptake kinetics. The adsorption isotherms for As (III) and As (V) fitted both the Langmuir and Freundlich models. A major advantage of the MWCNT-ZrO2 was that the adsorption capacity was not a function of pH. PMID:22424815

Optimization of the combined ultrasonic assisted/adsorption method for the removal of malachite green by gold nanoparticles loaded on activated carbon: Experimental design

NASA Astrophysics Data System (ADS)

Roosta, M.; Ghaedi, M.; Shokri, N.; Daneshfar, A.; Sahraei, R.; Asghari, A.

2014-01-01

The present study was aimed to experimental design optimization applied to removal of malachite green (MG) from aqueous solution by ultrasound-assisted removal onto the gold nanoparticles loaded on activated carbon (Au-NP-AC). This nanomaterial was characterized using different techniques such as FESEM, TEM, BET, and UV-vis measurements. The effects of variables such as pH, initial dye concentration, adsorbent dosage (g), temperature and sonication time on MG removal were studied using central composite design (CCD) and the optimum experimental conditions were found with desirability function (DF) combined response surface methodology (RSM). Fitting the experimental equilibrium data to various isotherm models such as Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich models show the suitability and applicability of the Langmuir model. Kinetic models such as pseudo -first order, pseudo-second order, Elovich and intraparticle diffusion models applicability was tested for experimental data and the second-order equation and intraparticle diffusion models control the kinetic of the adsorption process. The small amount of proposed adsorbent (0.015 g) is applicable for successful removal of MG (RE > 99%) in short time (4.4 min) with high adsorption capacity (140-172 mg g-1).

Optimization of the ultrasonic assisted removal of methylene blue by gold nanoparticles loaded on activated carbon using experimental design methodology.

PubMed

Roosta, M; Ghaedi, M; Daneshfar, A; Sahraei, R; Asghari, A

2014-01-01

The present study was focused on the removal of methylene blue (MB) from aqueous solution by ultrasound-assisted adsorption onto the gold nanoparticles loaded on activated carbon (Au-NP-AC). This nanomaterial was characterized using different techniques such as SEM, XRD, and BET. The effects of variables such as pH, initial dye concentration, adsorbent dosage (g), temperature and sonication time (min) on MB removal were studied and using central composite design (CCD) and the optimum experimental conditions were found with desirability function (DF) combined response surface methodology (RSM). Fitting the experimental equilibrium data to various isotherm models such as Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich models show the suitability and applicability of the Langmuir model. Analysis of experimental adsorption data to various kinetic models such as pseudo-first and second order, Elovich and intraparticle diffusion models show the applicability of the second-order equation model. The small amount of proposed adsorbent (0.01 g) is applicable for successful removal of MB (RE>95%) in short time (1.6 min) with high adsorption capacity (104-185 mg g(-1)). Copyright © 2013 Elsevier B.V. All rights reserved.

Cooked Food Waste-An Efficient and Less Expensive Precursor for the Generation of Activated Carbon.

PubMed

Krithiga, Thangavelu; Sabina, Xavier Janet; Rajesh, Baskaran; Ilbeygi, Hamid; Shetty, Adka Nityananda; Reddy, Ramanjaneya; Karthikeyan, Jayabalan

2018-06-01

Activated carbon was synthesized from cooked food waste, especially dehydrated rice kernels, by chemical activation method using NaOH and KOH as activating agents. It was then characterized by ultimate and proximate analysis, BET surface analysis, XRD, FTIR, Raman and SEM. The XRD patterns and Raman spectra confirmed the amorphous nature of the prepared activated carbons. Ultimate analysis showed an increase in the carbon content after activation of the raw carbon samples. Upon activation with NaOH and KOH, the surface area of the carbon sample was found to have increased from 0.3424 to 539.78 and 306.83 m2g-1 respectively. The SEM images revealed the formation of heterogeneous pores on the surface of the activated samples. The samples were then tested for their adsorption activity using acetic acid and methylene blue. Based on the regression coefficients, the adsorption kinetics of methylene blue dye were fitted with pseudo-second order model for both samples. Similarly, the Freundlich isotherm was found to be a better fit than Langmuir isotherm for both samples. The activity of thus prepared activated carbons was found to be comparable with the commercial carbon.

Kinetic and isotherm analyses for thorium (IV) adsorptive removal from aqueous solutions by modified magnetite nanoparticle using response surface methodology (RSM)

NASA Astrophysics Data System (ADS)

Karimi, Mohammad; Milani, Saeid Alamdar; Abolgashemi, Hossein

2016-10-01

In this study, the ability and the adsorption capacity of magnetite/aminopropyltriethoxysilane/glutaraldehyde (Fe3O4/APTES/GA) adsorbent were evaluated for the adsorption of thorium (IV) ions from aqueous solutions. The influence of the several variables such as pH (1-5), Th (IV) initial concentration (50-300 mg L-1) and adsorbent concentration (1-5 g L-1) on the Th (IV) adsorption were investigated by response surface methodology (RSM). The results showed that the highest absorption capacity (q) was 107.23 mg g-1 with respect to pH = 4.5, initial concentration of 250 mg L-1 and adsorbent concentration of 1 g L-1 for 90 min. Modeling equilibrium sorption data with the Langmuir, Freundlich and Dubinin-Radushkevich models pointed out that the results were in good agreement with Langmuir model. The experimental kinetic data were well fitted to pseudo-second-order equation with R2 = 0.9739. Also thermodynamic parameters (ΔGo, ΔHo, ΔSo) declared that the Th (IV) adsorption was endothermic and spontaneous.

Removal of Organophosphorus Pesticides from Aqueous Solution by Magnetic Fe3O4/Red Mud-Nanoparticles.

PubMed

Aydin, Senar

2016-12-01

  The aim of this study was to investigate the usability of magnetic Fe3O4/red mud nanoparticles (NPs) for the removal of organophosphorus pesticides from water samples. The effect of various experimental parameters such as red mud amount in Fe3O4/red mud-NPs, pH, contact time, initial pesticide concentrations and adsorbent dose was studied in order to find the optimum conditions for their removal in a batch process. The Fe3O4/red mud-NPs were characterized by using TGA, SEM, XRD, VSM, and determination of the BET surface area. After the regenerated Fe3O4/red mud-NPs were used three times, the sorption capacity and the magnetic separability were observed to be unaffected. Freundlich model described the sorption process better than Langmuir isotherm and the pseudo second-order kinetic model was determined as the best-fit model. The film diffusion mechanism was found to be a main rate control mechanism. The Fe3O4/red mud-NPs satisfactorily removed the OPPS from real water samples.

Competitive sorption affinity of sulfonamides and chloramphenicol antibiotics toward functionalized biochar for water and wastewater treatment.

PubMed

Ahmed, Mohammad Boshir; Zhou, John L; Ngo, Huu Hao; Guo, Wenshan; Johir, Md Abu Hasan; Belhaj, Dalel

2017-08-01

Competitive sorption of sulfamethazine (SMT), sulfamethoxazole (SMX), sulfathiazole (STZ) and chloramphenicol (CP) toward functionalized biochar (fBC) was highly pH dependent with maximum sorption at pH ∼4.0-4.25. Equilibrium data were well represented by the Langmuir and Freundlich models in the order STZ>SMX>CP>SMT. Kinetics data were slightly better fitted by the pseudo second-order model than pseudo first-order and intra-particle-diffusion models. Maximum sorptive interactions occurred at pH 4.0-4.25 through H-bonds formations for neutral sulfonamides species and through negative charge assisted H-bond (CAHB) formation for CP, in addition to π-π electron-donor-acceptor (EDA) interactions. EDA was the main mechanism for the sorption of positive sulfonamides species and CP at pH<2.0. Sorption of negative sulfonamides species and CP at pH>7.0 was regulated by H-bond formation and proton exchange with water by forming CAHB, respectively. The results suggested fBC to be highly efficient in removing antibiotics mixture. Copyright © 2017 Elsevier Ltd. All rights reserved.

Kinetics and thermodynamics of Pb(II) adsorption onto modified spent grain from aqueous solutions

NASA Astrophysics Data System (ADS)

Li, Qingzhu; Chai, Liyuan; Yang, Zhihui; Wang, Qingwei

2009-01-01

Spent grain, a main by-product of the brewing industry, is available in large quantities, but its main application has been limited to animal feeding. Nevertheless, in this study, spent grain modified with 1 M NaCl solution as a novel adsorbent has been used for the adsorption of Pb(II) in aqueous solutions. Isotherms, kinetics and thermodynamics of Pb(II) adsorption onto modified spent grain were studied. The equilibrium data were well fitted with Langmuir, Freundlich and Dubinin-Radushkevick (D-R) isotherm models. The kinetics of Pb(II) adsorption followed pseudo-second-order model, using the rate constants of pseudo-second-order model, the activation energy ( Ea) of Pb(II) adsorption was determined as 12.33 kJ mol -1 according to the Arrhenius equation. Various thermodynamic parameters such as Δ Gads, Δ Hads and Δ Sads were also calculated. Thermodynamic results indicate that Pb(II) adsorption onto modified spent grain is a spontaneous and endothermic process. Therefore, it can be concluded that modified spent grain as a new effective adsorbent has potential for Pb(II) removal from aqueous solutions.

Adsorption of Zinc(II) on diatomite and manganese-oxide-modified diatomite: a kinetic and equilibrium study.

PubMed

Caliskan, Necla; Kul, Ali Riza; Alkan, Salih; Sogut, Eda Gokirmak; Alacabey, Ihsan

2011-10-15

The removal of Zn(II) ions from aqueous solution was studied using natural and MnO(2) modified diatomite samples at different temperatures. The linear Langmuir, Freundlich and Dubinin-Radushkevich (D-R) adsorption equations were applied to describe the equilibrium isotherms. From the D-R model, the mean adsorption energy was calculated as >8 kJ mol(-1), indicating that the adsorption of Zn(II) onto diatomite and Mn-diatomite was physically carried out. In addition, the pseudo-first-order, pseudo-second-order and intraparticle diffusion models were used to determine the kinetic data. The experimental data were well fitted by the pseudo-second-order kinetic model. Thermodynamic parameters such as the enthalpy (ΔH(0)), Gibbs' free energy (ΔG(0)) and entropy (ΔS(0)) were calculated for natural and MnO(2) modified diatomite. These values showed that the adsorption of Zn(II) ions onto diatomite samples was controlled by a physical mechanism and occurred spontaneously. Copyright © 2011 Elsevier B.V. All rights reserved.

Biosorption of praseodymium (III) using Terminalia arjuna bark powder in batch systems: isotherm and kinetic studies.

PubMed

Swain, Krishna Kumari; Mishra, Pravat Manjari; Devi, Aparna Prabha

2018-02-01

The high demand for rare earth elements (REEs) used in various advanced materials implies demand for increased production of REEs or the recycling of solutions to recover the REEs they contain. In this study, the biosorption of Pr(III) from aqueous solution by bark powder of Terminalia arjuna was examined in a batch system as a function of metal concentration, biosorbent dosage, pH and contact time. Results showed that T. arjuna bark powder has a high affinity for adsorbing Pr(III): more than 90% at pH 6.63. The adsorption of Pr(III) by T. arjuna bark powder was investigated by the Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherm models. The kinetics of the biosorption process was tested with pseudo-first-order and pseudo-second-order models, and the results showed that the biosorption process was better fitted to the pseudo-second-order model. From Fourier transform infrared spectroscopy (FT-IR) analysis, it is confirmed that the biomolecules of T. arjuna bark powder are involved in the biosorption process of Pr(III) metal ions.

Marine green algae Codium iyengarii as a good bio-sorbent for elimination of reactive black 5 from aqueous solution.

PubMed

Azmat, Rafia

2014-09-01

The green seaweeds Codium iyengarii (C. iyengarii) was used to prepare as an adsorbent surface for the deletion of Reactive Black 5 (RB 5) from aqueous solution via adsorption. The batch technique was adopted under the optimal condition of amount of adsorbent, agitation time, concentration of dye, and at neutral and low pH. The depletion in concentration of the dye was monitored by Schimadzo 180 AUV/Visible spectrophotometer. It was initially monolayer adsorption, which showed multilayered formation later on with the passage of time at low and neutral pH. The Results displayed that adsorptive ability of C. iyengarii was 1.95-3.82mg/g with an elevation in primary application of dye contents (50ppm-70 ppm). The elimination data were well stable into the Langmuir and Freundlich adsorption isotherm equations. The Langmuir (R2=0.9848) and Freundlich (R2=0.9441) constants for biosorption of RB 5 on green algae were determined. The coefficient relation values suggested that the Langmuir isotherm was well fitted. It explained the interaction of surface molecules, which helps in well organization of dye molecules in a monolayer formation initially on algal biomass. The pseudo first and second order rate equations were applied to link the investigational statistics and found that the second order rate expression was found to be more suitable for both the models. The absorption spectrum of RB 5 before and after adsorption with respect to time was monitored which clearly indicate that C. iyengarii was much effective surface at very low quantity.

Conjugation of hydroxyapatite nanocrystals with human immunoglobulin G for nanomedical applications.

PubMed

Iafisco, Michele; Varoni, Elena; Di Foggia, Michele; Pietronave, Stefano; Fini, Milena; Roveri, Norberto; Rimondini, Lia; Prat, Maria

2012-02-01

Inorganic nanosized drug carriers are a promising field in nanomedicine applied to cancer. Their conjugation with antibodies combines the properties of the nanoparticles themselves with the specific and selective recognition ability of the antibodies to antigens. Biomimetic carbonate-hydroxyapatite (HA) nanoparticles were synthesized and fully characterized; human IgGs, used as model antibodies, were coupled to these nanocrystals. The maximum loading amount, the interaction modelling, the preferential orientation and the secondary structure modifications were evaluated using theoretical models (Langmuir, Freundlich and Langmuir-Freundlich) spectroscopic (UV-Vis, Raman), calorimetric (TGA), and immunochemical techniques (ELISA, Western Blot). HA nanoparticles of about 30 nm adsorbed human IgGs, in a dose-dependent, saturable and stable manner with micromolar affinity and adsorption capability around 2.3 mg/m(2). Adsorption isotherm could be described by Langmuir-Freundlich model, and was due to both energetically homogeneous and heterogeneous binding sites on HA surface, mainly of electrostatic nature. Binding did not induce secondary structure modification of IgGs. A preferential IgG end-on orientation with the involvement of IgG Fc moiety in the adsorption seems most probable due to the steric hindrance of their Fab domains. Biomimetic HA nanocrystals are suitable substrates to produce nanoparticles which can be functionalized with antibodies for efficient targeted drug delivery to tumours. Copyright © 2011 Elsevier B.V. All rights reserved.

Removal of anionic dye Congo red from aqueous solution by raw pine and acid-treated pine cone powder as adsorbent: equilibrium, thermodynamic, kinetics, mechanism and process design.

PubMed

Dawood, Sara; Sen, Tushar Kanti

2012-04-15

Pine cone a natural, low-cost agricultural by-product in Australia has been studied for its potential application as an adsorbent in its raw and hydrochloric acid modified form. Surface study of pine cone and treated pine cone was investigated using Fourier transform infrared (FTIR) and scanning electron microscopy (SEM). The modification process leads to increases in the specific surface area and decreases mean particle sizes of acid-treated pine cone when compared to raw pine cone biomass. Batch adsorption experiments were performed to remove anionic dye Congo red from aqueous solution. It was found that the extent of Congo red adsorption by both raw pine cone biomass and acid-treated biomass increased with initial dye concentration, contact time, temperature but decreased with increasing solution pH and amount of adsorbent of the system. Overall, kinetic studies showed that the dye adsorption process followed pseudo-second-order kinetics based on pseudo-first-order and intra-particle diffusion models. The different kinetic parameters including rate constant, half-adsorption time, and diffusion coefficient were determined at different physico-chemical conditions. Equilibrium data were best represented by Freundlich isotherm model among Langmuir and Freundlich adsorption isotherm models. It was observed that the adsorption was pH dependent and the maximum adsorption of 32.65 mg/g occurred at pH of 3.55 for an initial dye concentration of 20 ppm by raw pine cone, whereas for acid-treated pine cone the maximum adsorption of 40.19 mg/g for the same experimental conditions. Freundlich constant 'n' also indicated favourable adsorption. Thermodynamic parameters such as ∆G(0), ∆H(0), and ∆S(0) were calculated. A single-stage batch absorber design for the Congo red adsorption onto pine cone biomass also presented based on the Freundlich isotherm model equation. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Interactions Between Three Typical PPCPs and LDH

PubMed Central

Li, Erwei; Liao, Libing; Lv, Guocheng; Li, Zhaohui; Yang, Chengxue; Lu, Yanan

2018-01-01

With a layered structure, layered double hydroxide (LDH) has potential applications in remediation of anionic contaminants, which has been a hot topic for recent years. In this study, a Cl type Mg-Al hydrotalcite (Cl-LDH) was prepared by a co-precipitation method. The adsorption process of three pharmaceuticals and personal care products (PPCPs) [tetracycline (TC), diclofenac sodium (DF), chloramphenicol (CAP)] by Cl-LDH was investigated by X-ray diffraction (XRD), Zeta potential, dynamic light scattering (DLS), BET, Fourier transform infrared (FTIR) spectroscopy, and molecular dynamics simulation. The results showed that the adsorption equilibrium of TC and DF could be reached in 120 min, and the maximum adsorption capacity of the TC and DF were 1.85 and 0.95 mmol/g, respectively. The isothermal adsorption model of TC was fitted with the Freundlich adsorption model, and the isothermal adsorption model of DF was fitted with the Langmuir adsorption model. The adsorption dynamics of TC and DF followed the pseudo-second-order model. The adsorption mechanisms of the three PPCPs into Cl-LDH were different based on the experimental results and molecular dynamics simulation. The TC adsorption on Cl-LDH was accompanied by the electrostatic interactions between the negative charge of TC and the positive charge of Cl-LDH. The uptake of DF was attributed to anion exchange and electrostatic interaction. Cl-LDH does not adsorb CAP due to no electrostatic interaction. The molecular dynamic simulation further confirmed different configurations of three selected PPCPs, which were ultimately responsible for the uptake of PPCPs on Cl-LDH. PMID:29556493

Kinetic and isotherm modeling of Cd (II) adsorption by L-cysteine functionalized multi-walled carbon nanotubes as adsorbent.

PubMed

Taghavi, Mahmoud; Zazouli, Mohammad Ali; Yousefi, Zabihollah; Akbari-adergani, Behrouz

2015-11-01

In this study, multi-walled carbon nanotubes were functionalized by L-cysteine to show the kinetic and isotherm modeling of Cd (II) ions onto L-cysteine functionalized multi-walled carbon nanotubes. The adsorption behavior of Cd (II) ion was studied by varying parameters including dose of L-MWCNTs, contact time, and cadmium concentration. Equilibrium adsorption isotherms and kinetics were also investigated based on Cd (II) adsorption tests. The results showed that an increase in contact time and adsorbent dosage resulted in increase of the adsorption rate. The optimum condition of the Cd (II) removal process was found at pH=7.0, 15 mg/L L-MWCNTs dosage, 6 mg/L cadmium concentration, and contact time of 60 min. The removal percent was equal to 89.56 at optimum condition. Langmuir and Freundlich models were employed to analyze the experimental data. The data showed well fitting with the Langmuir model (R2=0.994) with q max of 43.47 mg/g. Analyzing the kinetic data by the pseudo-first-order and pseudo-second-order equations revealed that the adsorption of cadmium using L-MWSNTs following the pseudo-second-order kinetic model with correlation coefficients (R2) equals to 0.998, 0.992, and 0.998 for 3, 6, and 9 mg/L Cd (II) concentrations, respectively. The experimental data fitted very well with the pseudo-second-order. Overall, treatment of polluted solution to Cd (II) by adsorption process using L-MWCNT can be considered as an effective technology.

Comparison Between Dielectric Barrier Discharge Plasma and Ozone Regenerations of Activated Carbon Exhausted with Pentachlorophenol

NASA Astrophysics Data System (ADS)

Qu, Guangzhou; Liang, Dongli; Qu, Dong; Huang, Yimei; Li, Jie

2014-06-01

In this study, two regeneration methods (dielectric barrier discharge (DBD) plasma and ozone (O3) regeneration) of saturated granular activated carbon (GAC) with pentachlorophenol (PCP) were compared. The results show that the two regeneration methods can eliminate contaminants from GAC and recover its adsorption properties to some extent. Comparing the DBD plasma with O3 regeneration, the adsorption rate and the capacity of the GAC samples after DBD plasma regeneration are greater than those after O3 regeneration. O3 regeneration decreases the specific surface area of GAC and increases the acidic surface oxygen groups on the surface of GAC, which causes a decrease in PCP on GAC uptake. With increasing regeneration cycles, the regeneration efficiencies of the two methods decrease, but the decrease in the regeneration efficiencies of GAC after O3 regeneration is very obvious compared with that after DBD plasma regeneration. Furthermore, the equilibrium data were fitted by the Freundlich and Langmuir models using the non-linear regression technique, and all the adsorption equilibrium isotherms fit the Langmuir model fairly well, which demonstrates that the DBD plasma and ozone regeneration processes do not appear to modify the adsorption process, but to shift the equilibrium towards lower adsorption concentrations. Analyses of the weight loss of GAC show that O3 regeneration has a lower weight loss than DBD plasma regeneration.

Enhancing adsorption capacity of toxic malachite green dye through chemically modified breadnut peel: equilibrium, thermodynamics, kinetics and regeneration studies.

PubMed

Chieng, Hei Ing; Lim, Linda B L; Priyantha, Namal

2015-01-01

Breadnut skin, in both its unmodified (KS) and base-modified (BM-KS) forms, was investigated for its potential use as a low-cost adsorbent for the removal of toxic dye, malachite green (MG). Characterization of the adsorbents was carried out using scanning electron microscope, X-ray fluorescence and Fourier transform infra-red spectroscopy. Batch adsorption experiments, carried out under optimized conditions, for the adsorption of MG were fitted using five isotherm models (Langmuir, Freundlich, Dubinin-Radushkevich, Temkin and Sips) and six error functions to determine the best-fit model. The adsorption capacity was greatly enhanced when breadnut skin was chemically modified with NaOH, leading to an adsorption capacity of 353.0 mg g(-1), that was far superior to most reported adsorbents for the removal of MG. Thermodynamics studies indicated that the adsorption of MG was spontaneous on KS and BM-KS, and the reactions were endothermic and exothermic, respectively. Kinetics studies showed that both followed the pseudo-second order. Regeneration experiments on BM-KS indicated that its adsorption capacity was still maintained at>90% even after five cycles. It can be concluded that NaOH-modified breadfruit skin has great potential to be utilized in real-life application as a low-cost adsorbent for the removal of MG in wastewater treatment.

The removal of uranium (VI) from aqueous solutions onto activated carbon developed from grinded used tire.

PubMed

Belgacem, Ahmed; Rebiai, Rachid; Hadoun, Hocine; Khemaissia, Sihem; Belmedani, Mohamed

2014-01-01

In this study, activated carbon was prepared from waste tire by KOH chemical activation. The pore properties including the BET surface area, pore volume, pore size distribution, and average pore diameter were characterized. BET surface area of the activated carbon was determined as 558 m(2)/g. The adsorption of uranium ions from the aqueous solution using this activated carbon has been investigated. Various physico-chemical parameters such as pH, initial metal ion concentration, and adsorbent dosage level and equilibrium contact time were studied by a batch method. The optimum pH for adsorption was found to be 3. The removal efficiency has also been determined for the adsorption system as a function of initial concentration. The experimental results were fitted to Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models. A comparison of best-fitting was performed using the coefficient of correlation and the Langmuir isotherm was found to well represent the measured sorption data. According to the evaluation using the Langmuir equation, the saturated monolayer sorption capacity of uranium ions onto waste tire activated carbon was 158.73 mg/g. The thermodynamic equilibrium constant and the Gibbs free energy were determined and results indicated the spontaneous nature of the adsorption process. Kinetics data were best described by pseudo-second-order model.

Adsorption Study on Moringa Oleifera Seeds and Musa Cavendish as Natural Water Purification Agents for Removal of Lead, Nickel and Cadmium from Drinking Water

NASA Astrophysics Data System (ADS)

Aziz, N. A. A.; Jayasuriya, N.; Fan, L.

2016-07-01

The effectiveness of plant based materials Moringa oleifera (Moringa) seeds and Musa cavendish (banana peel) for removing heavy metals namely lead (Pb), nickel (Ni) and cadmium (Cd) from contaminated groundwater was studied. Tests were carried out with individual and combined biomass at neutral pH condition on synthetic groundwater samples. The optimum biomass doses were determined as 200 mg/L for single biomass and 400 mg/L (in the ratio of 200 mg/L: 200 mg/L) for combined biomasses and used for adsorption isotherm studies with contact time of 30 minutes. Results showed that combined biomasses was able to met the Pb, Ni and Cd WHO standards from higher Pb, Ni and Cd initial concentrations which were up to 40 µg/L, 50 µg/L 9 µg/L, respectively compared to individual biomass of Moringa seed and banana peel. Moringa seeds exhibited the highest removal of Pb (81%) while the combined biomasses was most effective in removing Ni (74%) and Cd (97%) over wider their initial concentration ranges. The experimental data were linearized with Langmuir and Freundlich adsorption isotherm models. Freundlich model described the Pb adsorption better than the Langmuir model for all the tested biomasses. However, the Langmuir model fit better with the experimental data of Ni adsorption by Moringa seeds. Both models showed negligible differences in the coefficient of determination (R2) when applied for Ni and Cd adsorption on banana peel and combined biomasses, suggesting that there were multiple layers on the biomass interacting with the metals. Chemisorption is suggested to be involved in Pb adsorption for all tested biomasses as the value of nF calculated was lower than one. This type of adsorption could explain the phenomenon of different behavior of Pb removal and the higher Pb adsorption capacity (represented by KF values) compared to Ni and Cd. The study demonstrates that Moringa seeds, banana peel and their combination have the potential to be used as a natural alternative to the other water treatment agents for removing the Pb, Ni and Cd from drinking water.

Removal of low-concentration phosphorus using a fluidized raw dolomite bed.

PubMed

Ayoub, George M; Kalinian, Houri

2006-04-01

Raw dolomite powder, obtained from dolomitic rocks, was evaluated for its efficiency in removing low concentrations of phosphate present in various water and wastewater matrices. A variety of experimental setups and process variables were tested, in an attempt to determine the optimal scheme (fluidized bed) that will be used to accomplish the objectives of the study. Test influents, including distilled water (DW), synthetic groundwater (SGW), tap water (TW), and sodium-hydroxide (NaOH)-alkalized wastewater treated with liquid bittern (STSE-B) and wastewater treated with lime (STSE-L) were used to assess the effect of influent parameters on the quality of the effluent generated. The adsorptive behavior of dolomite was described by fitting data generated from the study into the Freundlich and Langmuir isotherm models. Regeneration of the dolomite was attempted by the use of an acid (hydrochloric acid), DW, and an alkaline (NaOH). Test results indicate remarkable phosphate removal levels for DW and SGW. Removal levels of 100% were attained, for an average of 307 and 314 bed volumes at inflow concentration levels of 0.28 and 0.34 mg phosphate (PO4)/ L, respectively. Relative adsorption capacities were calculated to be 0.06 and 0.072 mg PO4/g of dolomite, respectively. For TW, STSE-L, and STSE-B, 100% removal before the start of the breakthrough was sustained for averages of 205, 94, and 28 bed volumes at phosphate dosages of 0.34, 0.56, and 0.6 mg PO4/L, respectively. The calculated adsorptive capacities were 0.05, 0.051, and 0.025, respectively. Zeta potential measurement resulted in values of -16.0 mV before treatment and +3.0 mV after complete exhaustion of the bed with PO4-jacked SGW influent, indicating an ionic adsorption of ions of opposite charge to that of the particle surface. Although both the Freundlich and Langmuir isotherms were found to fit the sorption curves, the Langmuir seems to better describe the sorption process in dolomite. Among the three attempted dolomite regeneration processes, the use of NaOH has shown to be the most successful.

Potential for use of industrial waste materials as filter media for removal of Al, Mo, As, V and Ga from alkaline drainage in constructed wetlands--adsorption studies.

PubMed

Hua, T; Haynes, R J; Zhou, Y-F; Boullemant, A; Chandrawana, I

2015-03-15

The potential to remove Al, Mo, V, As and Ga from alkaline (pH 8.0-8.6) drainage originating from seawater neutralized bauxite processing residue storage areas using constructed wetland technology was studied in a laboratory study. Bauxite processing residue sand, bauxite, alum water treatment sludge and blast furnace slag were investigated as potential active filter materials. Al was shown to precipitate as Al(OH)3 in the pH range 7.0-8.0 in aqueous solution and 6.0-8.5 in the presence of silica sand particles that provided a surface for nucleation. For V As Mo and Ga, adsorption to the surfaces of the adsorbents decreased greatly at elevated pH values (>pH 6-9). Water treatment sludge and bauxite had a greater ability to adsorb V, As and Mo at high pH (As and V at pH 7-9 and Mo at pH 5-7) than processing sand and slag. Adsorption isotherm data for As and V onto all four adsorbent than processing sand and slag. Adsorption isotherm data for As and V onto all four adsorbent materials fitted equally well to the Langmuir and Freundlich equations but for Ga, and to a lesser extent Mo, the Freundlich equation gave higher R(2) values. For all four ions, the maximum adsorption capacity (Langmuir value qmax) was greatest for water treatment sludge. Bauxite adsorbed more Mo, Ga and V than residue sand or slag. The pseudo-second order equation gave a better fit to the experimental kinetic data than the pseudo-first order model suggesting that chemisorption rather than diffusion/exchange was the rate limiting step to adsorption. It was concluded that water treatment sludge and bauxite were the most effective adsorbents and that for effective removal of the target ions the pH of the drainage water needs to be decreased to 6.0-7.0. Copyright © 2015 Elsevier Ltd. All rights reserved.

Potential adsorption of methylene blue from aqueous solution using green macroalgaePosidonia oceanica.

NASA Astrophysics Data System (ADS)

Allouche, F.-N.; Yassaa, N.

2018-03-01

The use of inexpensive biological materials, such as marine algae for removing dyes from contaminated industrial effluents appears as a potential alternative method. The aim of this study is to investigate the aptitude of marine macroalgae Posidonia Oceanica local biomass abundant on the coasts of Algeria for selective sorption of methylene blue (MB) from an aqueous solution in batch experiments at 20 °C. A maximum percentage removal of Posidonia oceanica occurs at pH 5. Equilibrium isotherm data were analyzed using the Langmuir and the Freundlich isotherms. The adsorption equilibrium of methylene blue was best describe by Langmuir model than the Freundlich model. The maximum sorption capacity was 357 mgg-1at pH 5. The sorption data were very well described by the pseudo-second-order model. Keywords: Posidonia oceanica, Methylene blue (MB), Biosorption, Isotherm Equilibrium, Kinetics; Modelling.

Adsorptive Removal and Adsorption Kinetics of Fluoroquinolone by Nano-Hydroxyapatite

PubMed Central

Chen, Yajun; Lan, Tao; Duan, Lunchao; Wang, Fenghe; Zhao, Bin; Zhang, Shengtian; Wei, Wei

2015-01-01

Various kinds of antibiotics, especially fluoroquinolone antibiotics (FQs) have been widely used for the therapy of infectious diseases in human and livestock. For their poorly absorbed by living organisms, large-scale misuse or abuse of FQs will foster drug resistance among pathogenic bacteria, as well as a variety of environmental problems when they were released in the environment. In this work, the adsorption properties of two FQs, namely norfloxacin (NOR) and ciprofloxacin (CIP), by nano-hydroxyapatite (n-HAP) were studied by batch adsorption experiments. The adsorption curves of FQs by n-HAP were simulated by Langmuir and Freundlich isotherms. The results shown that NOR and CIP can be adsorbed effectively by the adsorbent of n-HAP, and the adsorption capacity of FQs increase with increasing dosage of n-HAP. The optimum dosage of n-HAP for FQs removal was 20 g·L-1, in which the removal efficiencies is 51.6% and 47.3%, and an adsorption equilibrium time is 20 min. The maximum removal efficiency occurred when pH is 6 for both FQs. The adsorption isotherm of FQs fits well for both Langmuir and Freundlich equations. The adsorption of both FQs by n-HAP follows second-order kinetics. PMID:26698573

Synthesis of iron oxyhydroxide-coated rice straw (IOC-RS) and its application in arsenic(V) removal from water.

PubMed

Ouédraogo, Igor W K; Pehlivan, Erol; Tran, Hien T; Bonzi-Coulibaly, Yvonne L; Zachmann, Dieter; Bahadir, Müfit

2015-09-01

Because of the recognition that arsenic (As) at low concentrations in drinking water causes severe health effects, the technologies of As removal have become increasingly important. In this study, a simplified and effective method was used to immobilize iron oxyhydroxide onto a pretreated naturally occurring rice straw (RS). The modified RS adsorbent was characterized, using scanning electron microscope, Fourier transform infrared spectroscopy, thermogravimetric analyzer, and surface area analyzer. Experimental batch data of As(V) adsorption were modeled by the isotherms and kinetics models. Although all isotherms, the Langmuir model fitted the equilibrium data better than Freundlich and Dubinin-Radushkevich models and confirmed the surface homogeneity of adsorbent. The iron oxyhydroxide-coated rice straw (IOC-RS) was found to be effective for the removal of As(V) with 98.5% sorption efficiency at a concentration of <50 mg/L of As(V) solution, and thus maximum uptake capacity is ∼22 and 20 mg As(V)/g of IOC-RS at pH 4 and 6, respectively. The present study might provide new avenues to achieve the As concentrations required for drinking water recommended by the World Health Organization.

Adsorption of ferrous ions onto montmorillonites

NASA Astrophysics Data System (ADS)

Qin, Dawei; Niu, Xia; Qiao, Min; Liu, Gang; Li, Hongxin; Meng, Zhenxiao

2015-04-01

The adsorption of Fe (II) onto montmorillonites was investigated through initial concentration, contact time, pH and temperature. During the whole adsorption process, the ascorbic acid (Vitamin C) was added as a kind of antioxidant, at the same time, deionized water (after boiling) and nitrogen protection were also used to avoid oxidation. The Fe2+/Fetotal ratio of the iron exists in the Fe-montmorillonites was found more than 95%. Two kinetic models, including pseudo-first-order and pseudo-second-order model, were used to analyze the adsorption process of Fe (II) on montmorillonites. The results of our study showed that adsorption process fitted with pseudo-second-order well. Adsorption isotherms showed that Langmuir model was better than Freundlich model. The thermodynamic parameters ΔG0 and ΔH0 were 3.696 kJ/mol and 6.689 kJ/mol (we just gave the values at 298 K), respectively. The positive values at different temperatures showed that the adsorption process was non-spontaneous and endothermic. The characteristics of materials were determined by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Surface area and porosity analyzer, Thermogravimetric analysis (TGA), Differential scanning calorimeter (DSC) and Zeta potential distribution.

Biosorption of copper ions from dilute aqueous solutions on base treated rubber (Hevea brasiliensis) leaves powder: kinetics, isotherm, and biosorption mechanisms.

PubMed

Wan Ngah, W S; Hanafiah, M A K M

2008-01-01

The efficiency of sodium hydroxide treated rubber (Hevea brasiliensis) leaves powder (NHBL) for removing copper ions from aqueous solutions has been investigated. The effects of physicochemical parameters on biosorption capacities such as stirring speed, pH, biosorbent dose, initial concentrations of copper, and ionic strength were studied. The biosorption capacities of NHBL increased with increase in pH, stirring speed and copper concentration but decreased with increase in biosorbent dose and ionic strength. The isotherm study indicated that NHBL fitted well with Langmuir model compared to Freundlich and Dubinin-Radushkevich models. The maximum biosorption capacity determined from Langmuir isotherm was 14.97 mg/g at 27 degrees C. The kinetic study revealed that pseudosecond order model fitted well the kinetic data, while Boyd kinetic model indicated that film diffusion was the main rate determining step in biosorption process. Based on surface area analysis, NHBL has low surface area and categorized as macroporous. Fourier transform infrared (FT-IR) analyses revealed that hydroxyl, carboxyl, and amino are the main functional groups involved in the binding of copper ions. Complexation was one of the main mechanisms for the removal of copper ions as indicated by FT-IR spectra. Ion exchange was another possible mechanism since the ratio of adsorbed cations (Cu2+ and H+) to the released cations (Na+, Ca2+, and Mg2+) from NHBL was almost unity. Copper ions bound on NHBL were able to be desorbed at > 99% using 0.05 mol/L HCl, 0.01 mol/L HNO3, and 0.01 mol/L EDTA solutions.

Factors influencing sorption of ciprofloxacin onto activated sludge: experimental assessment and modelling implications.

PubMed

Polesel, Fabio; Lehnberg, Kai; Dott, Wolfgang; Trapp, Stefan; Thomas, Kevin V; Plósz, Benedek Gy

2015-01-01

Many of the pharmaceuticals and personal care products occurring in municipal sewage are ionizing substances, and their partitioning behaviour is affected by ionic interactions with solid matrices. In activated sludge systems, such interactions have currently not been adequately understood and described, particularly for zwitterionic chemicals. Here we present an assessment of the effects of pH and iron salt dosing on the sorption of ciprofloxacin onto activated sludge using laboratory experiments and full-scale fate modelling. Experimental results were described with Freundlich isotherms and showed that non-linear sorption occurred under all the conditions tested. The greatest sorption potential was measured at pH=7.4, at which ciprofloxacin is speciated mostly as zwitterion. Iron salt dosing increased sorption under aerobic and, to a lesser extent, anoxic conditions, whereas no effect was registered under anaerobic conditions. The activated sludge model for xenobiotics (ASM-X) was extended with Freundlich-based sorption kinetics and used to predict the fate of ciprofloxacin in a wastewater treatment plant (WWTP). Scenario simulations, using experimental Freundlich parameters, were used to identify whether the assessed factors caused a significant increase of aqueous ciprofloxacin concentration in full-scale bioreactors. Simulation results suggest that a pH increase, rather than a reduction in iron salt dosing, could be responsible for a systematic deterioration of sorption of ciprofloxacin in the WWTP. Copyright © 2014 Elsevier Ltd. All rights reserved.

Adsorptive removal of dissolved organic matter (DOM) in landfill leachate by iron oxide nanoparticles (FeONPs)

NASA Astrophysics Data System (ADS)

Ghani, Zaidi Ab; Yusoff, Mohd Suffian; Zaman, Nastaein Qamaruz; Andas, Jeyashelly; Aziz, Hamidi Abdul

2017-10-01

A study was conducted to investigate the efficiency of iron oxide nanoparticle (FeONPs) adsorption for removing of DOM in landfill leachate. FeONPs was directly prepared via sodium borohydride (KBH4) reduction method. Adsorption kinetics, isotherm and thermodynamic studies were developed to design the model for DOM removal. Pseudo first-order and pseudo second-order model have been studied to fit the experimental data. The regression results showed that the adsorption kinetics were more accurately represented by a pseudo second-order model. The Weber-Morris intraparticle diffusion model was used to analyze the adsorption kinetics data. The plot of qt versus t1/2 represents multi linearity, which showed that the adsorption processes occurred in more than one step. Adsorption isotherms were analyzed by Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich, isotherms model. Equilibrium data were well fitted to the Dubinin- Radushkevich isotherm model. Maximum monolayer adsorption based on Langmuir was calculated to be 21.74 mg/g. Thermodynamic parameters such as free energy changes (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were evaluated between temperatures of 25 °C and 40 °C. The ΔG° was noticed progressively decrease from -9.620 -9.820 -10.021, and -10.222 kJ/mol as the temperature increase. The ΔH° and ΔS° values were found to be 2.350 kJ/mol and 40.165 J/mol.K respectively. The results showed that the overall adsorption process was endothermic and spontaneous. The results from this study suggested that FeNPs could be a viable adsorbent in managing higher DOM problems associated with landfill leachate.

Adsorption of methyl orange from aqueous solution by aminated pumpkin seed powder: Kinetics, isotherms, and thermodynamic studies.

PubMed

Subbaiah, Munagapati Venkata; Kim, Dong-Su

2016-06-01

Present research discussed the utilization of aminated pumpkin seed powder (APSP) as an adsorbent for methyl orange (MO) removal from aqueous solution. Batch sorption experiments were carried to evaluate the influence of pH, initial dye concentration, contact time, and temperature. The APSP was characterized by using Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The experimental equilibrium adsorption data were fitted using two two-parameter models (Langmuir and Freundlich) and two three-parameter models (Sips and Toth). Langmuir and Sips isotherms provided the best model for MO adsorption data. The maximum monolayer sorption capacity was found to be 200.3mg/g based on the Langmuir isotherm model. The pseudo-first-order and pseudo-second-order model equations were used to analyze the kinetic data of the adsorption process and the data was fitted well with the pseudo-second-order kinetic model (R(2)>0.97). The calculated thermodynamic parameters such as ΔG(0), ΔH(0) and ΔS(0) from experimental data showed that the sorption of MO onto APSP was feasible, spontaneous and endothermic in the temperature range 298-318 K. The FTIR results revealed that amine and carboxyl functional groups present on the surface of APSP. The SEM results show that APSP has an irregular and porous surface which is adequate morphology for dye adsorption. Desorption experiments were carried to explore the feasibility of adsorbent regeneration and the adsorbed MO from APSP was desorbed using 0.1M NaOH with an efficiency of 93.5%. Findings of the present study indicated that APSP can be successfully used for removal of MO from aqueous solution. Copyright © 2016 Elsevier Inc. All rights reserved.

[Sorption mechanism of ofloxacin by carbon nanotubes].

PubMed

Zhao, Xing-Xing; Yu, Shui-Li; Wang, Zhe

2014-02-01

Sorption of ofloxacin (OFL) by carbon nanotubes is an effective method to control its fate in aquatic environment. The sorption process of OFL by mixed acid-treated and non-treated multi-walled carbon nanotubes was discussed. Sorption kinetics, sorption isotherm, desorption, sorption thermodynamics and effect of pH were investigated. The results indicated that the sorption kinetics followed the pseudo-second order kinetics model. The equilibrium sorption capacity of OFL on MWCNTs-O was higher. The sorption isotherm could be fitted by both the Langmuir and Freundlich models. The equilibrium sorption capacity dropped when the pH of aqueous solution was in the range of 6.0 to 10.0. Obvious desorption hysteresis was observed during the desorption experiments, especially on MWCNTs-O. Sorption thermodynamics analysis showed that the interactions between the OFL and sorbents were mainly between molecules. More oxygen-containing functional groups introduced on MWCNTs provided OFL molecules with more sorptive sites, which facilitated the generation of hydrogen bonds, a relatively strong interaction. The hydrogen bonds dominated the sorption process of OFL by MWCNTs/MWCNTs-O, explaining the experimental phenomena.

Grape stalks biomass as raw material for activated carbon production: synthesis, characterization and adsorption ability

NASA Astrophysics Data System (ADS)

Hashemi Shahraki, Zahra; Sharififard, Hakimeh; Lashanizadegan, Asghar

2018-05-01

In order to produce activated carbon from grape stalks, this biomass was activated chemically with KOH. Identification methods including FTIR, BET, SEM, Boehm titration and pHzpc measurement were applied to characterize the produced carbon. The adsorption ability of produced activated carbon toward cadmium removal from aqueous solution was evaluated by using Central Composite Design methodology and the effects of process parameters were analysed, as well as, the optimum processing conditions were determined using statistical methods. In order to characterize the equilibrium behaviour of adsorption process, the equilibrium data were analysed by Langmuir, Freundlich, and R-D isotherm models. Results indicated that the adsorption process is a monolayer process and the adsorption capacity of prepared activated carbon was 140.84 mg L‑1. Analysis of kinetics data showed that the pseudo-second-order and Elovich models were well fitted with the kinetics results and this suggests the domination of chemical adsorption. The regenerability results showed that the prepared activated carbon has a reasonable adsorption capacity toward cadmium after five adsorption/desorption cycles.

Preparation and characterization of corn cob activated carbon coated with nano-sized magnetite particles for the removal of Cr(VI).

PubMed

Nethaji, S; Sivasamy, A; Mandal, A B

2013-04-01

Activated carbon prepared from corn cob biomass, magnetized by magnetite nanoparticles (MCCAC) was used for the adsorption of hexavalent chromium from aqueous solution. The adsorbent was characterized by SEM, TEM, XRD, VSM, surface functionality and zero-point charge. The iron oxide nanoparticles were of 50 nm sizes and the saturation magnetization value for the adsorbent is 48.43 emu/g. Adsorption was maximum at pH 2. Isotherm data were modeled using Langmuir, Freundlich and Temkin isotherm. The prepared MCCAC had a heterogeneous surface. The maximum monolayer adsorption capacity was 57.37 mg/g. Kinetic studies were carried out and the data fitted the pseudo second-order equation. The mechanism of the adsorption process was studied by incorporating the kinetic data with intraparticle diffusion model, Bangham equation and Boyd plot. The adsorption was by chemisorption and the external mass transfer was the rate-determining step. A micro column was designed and the basic column parameters were estimated. Copyright © 2013 Elsevier Ltd. All rights reserved.

Removal of Hexavalent Chromium by Adsorption on Microwave Assisted Activated Carbon Prepared from Stems of Leucas Aspera

NASA Astrophysics Data System (ADS)

Shanmugalingam, A.; Murugesan, A.

2018-05-01

This study reports adsorption of Cr(VI) ions from aqueous solution using activated carbon that was prepared from stems of Leucas aspera. Eight hundred and fifty watts power of microwave radiation, 12 min of radiation time, 60% of ZnCl2 solution and 24 h of impregnation time are the optimal parameters to prepare efficient carbon effective activated carbon. It was designated as MWLAC (Microwave assisted Zinc chloride activated Leucas aspera carbon). Various adsorption characteristics such as dose of the adsorbent, agitation time, initial Cr(VI) ion concentration, pH of the solution and temperature on adsorption were studied for removal of Cr(VI) ions from aqueous solution by batch mode. Also the equilibrium adsorption was analyzed by the Langmuir, Freundlich, Tempkin and D-R isotherm models. The order of best describing isotherms was given based on R2 value. The pseudo-second-order kinetic model best fitted with the Cr(VI) adsorption data. Thermodynamic parameters were also determined and results suggest that the adsorption process is a spontaneous, endothermic and proceeded with increased randomness.

Sorption and leaching of benzalkonium chlorides in agricultural soils.

PubMed

Khan, Adnan Hossain; Macfie, Sheila M; Ray, Madhumita B

2017-07-01

The adsorption and leaching characteristics of two commonly used benzalkonium chlorides (BACs), benzyl dimethyl dodecyl ammonium chloride (BDDA) and benzyl dimethyl tetradecyl ammonium chloride (BDTA) using three agricultural soils with varied proportions of silt, sand, clay, and organic matter were determined. BACs are cationic surfactants used in large quantities for sanitary and personal care products and are abundant in environmental samples. Adsorption isotherm data (aqueous concentration in the range of 25-150 mg L -1 ) fitted the Langmuir model better than the Freundlich model. BDTA with a longer alkyl chain adsorbed more to soil compared to BDDA, and the soil with the highest percentage of clay adsorbed the most. Column tests conducted using soils amended with lime stabilised biosolids and artificial rain water at a flow rate of 0.2 mL min -1 indicate very low leaching of BACs. Less than 1% of the available BDDA leached through sandy loam soil column with a depth of 9 cm. Therefore, the possibility of BACs to become bioavailable through leaching is very low at environmentally relevant concentrations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Removal of phenol by powdered activated carbon prepared from coal gasification tar residue.

PubMed

Wang, Xiong-Lei; Shen, Jun; Niu, Yan-Xia; Wang, Yu-Gao; Liu, Gang; Sheng, Qing-Tao

2018-03-01

Coal gasification tar residue (CGTR) is a kind of environmentally hazardous byproduct generated in fixed-bed coal gasification process. The CGTR extracted by ethyl acetate was used to prepare powdered activated carbon (PAC), which is applied later for adsorption of phenol. The results showed that the PAC prepared under optimum conditions had enormous mesoporous structure, and the iodine number reached 2030.11 mg/g, with a specific surface area of 1981 m 2 /g and a total pore volume of 0.92 ml/g. Especially, without loading other substances, the PAC, having a strong magnetism, can be easily separated after it adsorbs phenol. The adsorption of phenol by PAC was studied as functions of contact time, temperature, PAC dosage, solution concentration and pH. The results showed a fast adsorption speed and a high adsorption capacity of PAC. The adsorption process was exothermic and conformed to the Freundlich models. The adsorption kinetics fitted better to the pseudo-second-order model. These results show that CGTR can be used as a potential adsorbent of phenols in wastewater.

Sorption of chlorophenols from aqueous solution by granular activated carbon, filter coal, pine and hardwood.

PubMed

Hossain, G S M; McLaughlan, R G

2012-09-01

Wood and coal, as low-cost sorbents, have been evaluated as an alternative to commercial granular activated carbon (GAC) for chlorophenol removal. Kinetic experiments indicated that filter coal had a significantly lower rate of uptake (approximately 10% of final uptake was achieved after three hours) than the other sorbents, owing to intra-particle diffusion limitations. The data fitted a pseudo-second-order model. Sorption capacity data showed that GAC had a high sorption capacity (294-467 mg g(-1)) compared with other sorbents (3.2-7.5 mg(g-1)). However, wood and coal had a greater sorption capacity per unit surface area than GAC. Sorption equilibrium data was best predicted using a Freundlich adsorption model. The sorption capacity for all sorbents was 2-chlorophenol < 4-chlorophenol < 2, 4-dichlorophenol, which correlates well with solute hydrophobicity, although the relative differences were much less for coal than the other sorbents. The results showed that pine, hardwood and filter coal can be used as sorbent materials for the removal of chlorophenol from water; however, kinetic considerations may limit the application of filter coal.

Effect of hydrophobicity of pharmaceuticals and personal care products for adsorption on activated carbon: Adsorption isotherms, kinetics and mechanism.

PubMed

Kaur, Harkirat; Bansiwal, Amit; Hippargi, Girivyankatesh; Pophali, Girish R

2017-09-11

Adsorption of three pharmaceuticals and personal care products (PPCPs), namely caffeine, ibuprofen and triclosan on commercial powdered activated carbon was examined in aqueous medium. The contaminants were chosen based on their diverse log K ow (octanol-water partition coefficient) viz. - 0.07 for caffeine, 3.97 for ibuprofen and 4.76 for triclosan to examine the role of hydrophobicity on adsorption process. The adsorbent characterisation was achieved using BET surface area, SEM, pore size distribution studies and FTIR. Influence of mass of PAC, contact time, solution pH and initial concentration on adsorption capacity of PAC was studied. Adsorption isotherms and kinetics were applied to establish the mechanism of adsorption. The kinetics followed pseudo-second order with physisorption occurring through particle diffusion. The Freundlich model fitted best among the isotherm models. The adsorption capacity increased in the order CFN < IBU < TCS which correlates with increasing hydrophobicity (log K ow ), molecular weight and decreasing water solubility, respectively. We conclude that micro-pollutant hydrophobicity contributes towards adsorption on activated carbon.

Removal of mercury from aqueous solutions using activated carbon prepared from agricultural by-product/waste.

PubMed

Rao, M Madhava; Reddy, D H K Kumar; Venkateswarlu, Padala; Seshaiah, K

2009-01-01

Removal of mercury from aqueous solutions using activated carbon prepared from Ceiba pentandra hulls, Phaseolus aureus hulls and Cicer arietinum waste was investigated. The influence of various parameters such as effect of pH, contact time, initial metal ion concentration and adsorbent dose for the removal of mercury was studied using a batch process. The experiments demonstrated that the adsorption process corresponds to the pseudo-second-order-kinetic models and the equilibrium adsorption data fit the Freundlich isotherm model well. The prepared adsorbents ACCPH, ACPAH and ACCAW had removal capacities of 25.88 mg/g, 23.66 mg/g and 22.88 mg/g, respectively, at an initial Hg(II) concentration of 40 mg/L. The order of Hg(II) removal capacities of these three adsorbents was ACCPH>ACPAH>ACCAW. The adsorption behavior of the activated carbon is explained on the basis of its chemical nature. The feasibility of regeneration of spent activated carbon adsorbents for recovery of Hg(II) and reuse of the adsorbent was determined using HCl solution.

Biosorption of toxic lead (II) ions using tomato waste (Solanum lycopersicum) activated by NaOH

NASA Astrophysics Data System (ADS)

Permatasari, Diah; Heraldy, Eddy; Lestari, Witri Wahyu

2016-02-01

This research present to uptake lead (II) ion from aqueous solutions by activated tomato waste. Biosorbent were characterized by applying Fourier Transform Infrared Spectroscopy (FTIR) and Surface Area Analyzer (SAA). The biosorption investigated with parameters including the concentration of NaOH, effects of solution pH, biosorbent dosage, contact time,and initial metal concentration. Experimental data were analyzed in terms of two kinetic model such us the pseudo-first order and pseudo-second order. Langmuir and Freundlich isotherm models were applied todescribe the biosorption process. According to the experiment, the optimum concentration of NaOH was achieved at 0.1 M. The maximum % lead (II) removal was achieved at pH 4 with 94.5%. Optimum biosorbentdosage were found as 0.1 g/25 mL solution while optimum contact time were found at 75 minutes. The results showed that the biosorption processes of Lead (II) followed pseudo-second order kinetics. Langmuir adsorption isotherm was found fit the adsorption data with amaximum capacity of 24.079 mg/g with anadsorption energy of 28.046 kJ/mol.

Synthesis of a novel alginate-rubber joint immobilization strains H-1 and its application in removal of Pb (II) from aqueous solution

NASA Astrophysics Data System (ADS)

Li, Huidong; Huo, Kaili; Li, Xiaolei; Zhang, Lin; Yun, Yueqing; Song, Lei; Bai, Runying; Liu, Yuhong

2018-02-01

In this study, a novel alginate-rubber-strains immobilized beads (ARSIBs) was synthesized at the optimum conditions that the concentration of sodium alginate was 4%; the volume of bacterial suspension was 75%; the quality of rubber powder was 3.2%; the crosslinking time was 24 h by the orthogonal experiments. The optimum conditions for Pb (II) adsorption were 1.2% ARSIBs, 100 mg L-1 initial concentrations, pH 5 and 3 h contact time. The equilibrium data were well fitted by the Freundlich isotherm model. The biosorption process was nearly consistent with the pseudo-second-order model. Meanwhile, the biosorption mechanism could be that Pb (II) was adsorbed by the hydroxyl and carboxyl, finally precipitated with phosphate in the form of NaPb4(PO4)3, Pb5(PO4)3(OH) and Pb(H2PO4)2 based on the spectra of FTIR and XRD, respectively. In addition, the stability of ARSIBs was enhanced due to the addition to the rubber powder in the process of wastewater treatment.

Morin Flavonoid Adsorbed on Mesoporous Silica, a Novel Antioxidant Nanomaterial

PubMed Central

Arriagada, Francisco; Correa, Olosmira; Günther, Germán; Nonell, Santi; Mura, Francisco; Olea-Azar, Claudio

2016-01-01

Morin (2´,3, 4´,5,7-pentahydroxyflavone) is a flavonoid with several beneficial health effects. However, its poor water solubility and it sensitivity to several environmental factors avoid its use in applications like pharmaceutical and cosmetic. In this work, we synthetized morin-modified mesoporous silica nanoparticles (AMSNPs-MOR) as useful material to be used as potential nanoantioxidant. To achieve this, we characterized its adsorption kinetics, isotherm and the antioxidant capacity as hydroxyl radical (HO•) scavenger and singlet oxygen (1O2) quencher. The experimental data could be well fitted with Langmuir, Freundlich and Temkin isotherm models, besides the pseudo-second order kinetics model. The total quenching rate constant obtained for singlet oxygen deactivation by AMSNPs-MOR was one order of magnitude lower than the morin rate constant reported previously in neat solvents and lipid membranes. The AMSNPs-MOR have good antioxidant properties by itself and exhibit a synergic effect with morin on the antioxidant property against hydroxyl radical. This effect, in the range of concentrations studied, was increased when the amount of morin adsorbed increased. PMID:27812111

Adsorption isotherm studies of chromium (VI) from aqueous solutions using sol-gel hydrotalcite-like compounds.

PubMed

Ramos-Ramírez, Esthela; Ortega, Norma L Gutiérrez; Soto, Cesar A Contreras; Gutiérrez, Maria T Olguín

2009-12-30

In under-developed countries, industries such as paint and pigment manufacturing, leather tanning, chrome plating and textile processing, usually discharge effluents containing Cr(VI) and Cr(III) into municipal sanitary sewers. It has been reported that Cr(VI) acts as a powerful epithelial irritant and as a human carcinogen. In the present work, hydrotalcite-like compounds with a Mg/Al ratio=2 were synthesized by the sol-gel method. The hydrotalcite-like compounds and their corresponding thermally treated products were characterized by powder X-ray diffraction, infrared spectroscopy and N(2) adsorption. The hydrotalcite-like compounds and the heated solids were used as adsorbents for Cr(VI) in aqueous solutions. Adsorption isotherm studies of Cr(VI) from aqueous solution are described. The adsorbent capacity was determined using the Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherm models. The Cr(VI) adsorption isotherm data fit best to the Langmuir isotherm model. The maximum Cr(VI) uptake by hydrotalcite and the heated solids was determined using the Langmuir equation and was found to range between 26 and 29 mg Cr(VI)/g adsorbent.

Metals sorption from aqueous solutions by Kluyveromyces marxianus: process optimization, equilibrium modeling and chemical characterization.

PubMed

Pal, Rama; Tewari, Saumyata; Rai, Jai P N

2009-10-01

The dead Kluyveromyces marxianus biomass, a fermentation industry waste, was used to explore its sorption potential for lead, mercury, arsenic, cobalt, and cadmium as a function of pH, biosorbent dosage, contact time, agitation speed, and initial metal concentration. The equilibrium data fitted the Langmuir model better for cobalt and cadmium, but Freundlich isotherm for all metals tested. At equilibrium, the maximum uptake capacity (Qmax) was highest for lead followed by mercury, arsenic, cobalt, and cadmium. The RL values ranged between 0-1, indicating favorable sorption of all test metals by the biosorbent. The maximum Kf value of Pb showed its efficient removal from the solution. However, multi-metal analysis depicted that sorption of all metals decreased except Pb. The potentiometric titration of biosorbent revealed the presence of functional groups viz. amines, carboxylic acids, phosphates, and sulfhydryl group involved in heavy metal sorption. The extent of contribution of functional groups and lipids to biosorption was in the order: carboxylic>lipids>amines>phosphates. Blocking of sulfhydryl group did not have any significant effect on metal sorption.

Optimization of the combined ultrasonic assisted/adsorption method for the removal of malachite green by gold nanoparticles loaded on activated carbon: experimental design.

PubMed

Roosta, M; Ghaedi, M; Shokri, N; Daneshfar, A; Sahraei, R; Asghari, A

2014-01-24

The present study was aimed to experimental design optimization applied to removal of malachite green (MG) from aqueous solution by ultrasound-assisted removal onto the gold nanoparticles loaded on activated carbon (Au-NP-AC). This nanomaterial was characterized using different techniques such as FESEM, TEM, BET, and UV-vis measurements. The effects of variables such as pH, initial dye concentration, adsorbent dosage (g), temperature and sonication time on MG removal were studied using central composite design (CCD) and the optimum experimental conditions were found with desirability function (DF) combined response surface methodology (RSM). Fitting the experimental equilibrium data to various isotherm models such as Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich models show the suitability and applicability of the Langmuir model. Kinetic models such as pseudo -first order, pseudo-second order, Elovich and intraparticle diffusion models applicability was tested for experimental data and the second-order equation and intraparticle diffusion models control the kinetic of the adsorption process. The small amount of proposed adsorbent (0.015 g) is applicable for successful removal of MG (RE>99%) in short time (4.4 min) with high adsorption capacity (140-172 mg g(-1)). Copyright © 2013. Published by Elsevier B.V.

Synthesis and structure of pyridine-functionalized mesoporous SBA-15 organosilicas and their application for sorption of diclofenac

NASA Astrophysics Data System (ADS)

Barczak, Mariusz

2018-02-01

A series of pyridine-functionalized mesoporous silicas have been prepared for the first time via direct co-condensation of tetraethoxysilane (TEOS) and 2-(2-pyridyl)ethyltrimethoxysilane (PETS) using the block copolymer Pluronic P123 as a structure-directing agent. The obtained materials were fully characterized by a wide range of instrumental techniques and employed as adsorbents for the removal of a diclofenac which is considered a priority hazardous drug. The synthesized materials exhibit a high adsorption capacities and rapid adsorption rates. The structural and adsorption properties depend largely on the relative amount of PETS/TEOS ratio: the gradual degradation of ordered structure and porosity was observed with the increasing amount of PETS. However due to the highest loading of pyridine units the most structurally degraded material had the highest adsorption uptake (631 mg g-1) indicating that the surface chemistry plays - along with porosity - an important role in governing the adsorption process. The experimental adsorption data were modelled using the Langmuir, Freundlich and Langmuir-Freundlich isotherms - among them the Langmuir-Freundlich model turned out to be the most suitable for describing adsorption behaviour of diclofenac onto the materials. The collected data show that the pyridine-functionalized mesoporous silicas can be a promising absorbent of pharmaceuticals.

Removal of nickel from aqueous solution using supported zeolite-Y hollow fiber membranes.

PubMed

Muhamad, Norfazilah; Abdullah, Norfazliana; Rahman, Mukhlis A; Abas, Khairul Hamimah; Aziz, Azian Abd; Othman, Mohd Hafiz Dzarfan; Jaafar, Juhana; Ismail, Ahmad Fauzi

2018-05-02

This work describes the development of supported zeolite-Y membranes, prepared using the hydrothermal method, for the removal of nickel from an aqueous solution. Alumina hollow fibers prepared using the phase inversion and sintering technique were used as an inert support. The supported zeolite-Y membranes were characterized using the field emission scanning electron microscope (FESEM), X-ray diffraction (XRD), and the water permeation and rejection test. The performance of the supported zeolite-Y membranes for heavy metal removal using batch adsorption and filtration test was studied using the atomic absorption spectroscopy (AAS). The adsorption study shows that the removal of nickel was pH-dependent but affected by the presence of α-alumina. The seeded zeolite-Y membrane gave the highest adsorption capacity which was 126.2 mg g -1 . This enabled the membrane to remove 63% of nickel ions from the aqueous solution within 180 min of contact time. The adsorption mechanism of nickel onto the zeolite-Y membrane was best fitted to the Freundlich isotherm. The kinetic study concluded that the adsorption was best fitted to pseudo-second-order model with higher correlation coefficient (R 2  = 0.9996). The filtration study proved that the zeolite-Y membrane enabled to reduce the concentration of heavy metal at parts per billion level.

Metal ion removal from aqueous solution using physic seed hull.

PubMed

Mohammad, Masita; Maitra, Saikat; Ahmad, Naveed; Bustam, Azmi; Sen, T K; Dutta, Binay K

2010-07-15

The potential of physic seed hull (PSH), Jantropha curcas L. as an adsorbent for the removal of Cd(2+) and Zn(2+) metal ions from aqueous solution has been investigated. It has been found that the amount of adsorption for both Cd(2+) and Zn(2+) increased with the increase in initial metal ions concentration, contact time, temperature, adsorbent dosage and the solution pH (in acidic range), but decreased with the increase in the particle size of the adsorbent. The adsorption process for both metal ions on PSH consists of three stages-a rapid initial adsorption followed by a period of slower uptake of metal ions and virtually no uptake at the final stage. The kinetics of metal ions adsorption on PSH followed a pseudo-second-order model. The adsorption equilibrium data were fitted in the three adsorption isotherms-Freundlich, Langmuir and Dubinin-Radushkevich isotherms. The data best fit in the Langmuir isotherm indication monolayer chemisorption of the metal ions. The adsorption capacity of PSH for both Zn(2+) and Cd(2+) was found to be comparable with other available adsorbents. About 36-47% of the adsorbed metal could be leached out of the loaded PSH using 0.1M HCl as the eluting medium. 2010 Elsevier B.V. All rights reserved.

Influence of dissolved organic matter on sorption and desorption of MCPA in ferralsol.

PubMed

Wu, Dongming; Yun, Yonghuan; Jiang, Lei; Wu, Chunyuan

2018-03-01

MCPA (4-chloro-2-methylphenoxyacetic acid) is an acidic herbicide, widely used in paddy fields. The presence of dissolved organic matter (DOM) modifies the sorption-desorption of herbicides in soils. In this study, effects of DOM on sorption- desorption of MCPA were tested using three typical ferralsol soil types from China: rhodic ferralsol, haplic ferralsol and paddy soil. DOM preparations were extracted from the paddy soil (DOM P ), from a compost mixture of cassava stems with chicken manure (DOM C ), and from rice straw (DOM R ). Sorption-desorption of MCPA in the tested soil types was shown to follow pseudo first-order kinetics, and the calculated isotherm data fitted well with a Freundlich equilibrium model in the range of the studied concentrations. MCPA was weakly sorbed by the soils, producing low Freundlich coefficient values (K f ) (0.854 to 4.237). The presence of DOM reduced the K f whereby DOM C had the strongest and DOM R the weakest effect. Presence of DOM also promoted MCPA desorption from the soils, again with DOM C having the strongest effect and DOM R the weakest. DOM coating changed the soil particle surface, as demonstrated by electron microscopy, and DOM also directly interacted with MCPA, as shown by Fourier-transform infrared spectroscopy. The experimental data were interpreted to suggest a competing sorption of DOM to ferralsol and an increased solubility of MCPA in the presence of DOM. The results indicate that the environmental risk of MCPA leaching to groundwater and surface flow is increased by presence of DOM, for instance as a result of organic fertilizer use. Copyright © 2017. Published by Elsevier B.V.

Adsorptive removal of dye using biochar derived from residual algae after in-situ transesterification: Alternate use of waste of biodiesel industry.

PubMed

Nautiyal, Piyushi; Subramanian, K A; Dastidar, M G

2016-11-01

The primary aim of this present study was to utilize the residual biomass (DB) of Spirulina platensis algae, left after in-situ transesterification, for biochar preparation. This is a solid waste residue of biodiesel industry. The biochar (BC) prepared was examined for its capacity to adsorb congo red dye from the aqueous solution. The results were compared with other adsorbents used in the study such as commercial activated carbon (AC), original algae biomass (AB) and DB. The results of proximate analysis of BC showed the decrease in the percentage of volatile matter and an increase in fixed carbon content compared to DB. The physico-chemical properties of BC were studied using elemental analysis, SEM, FTIR and XRD techniques. The AC and BC adsorbents showed better performance in removing 85.4% and 82.6% of dye respectively from solution compared to AB (76.6%) and DB (78.1%). The effect of initial dye concentration, adsorbent dosage and pH of solution on the adsorption phenomena was studied by conducting the batch adsorption experiments. The highest specific uptake for biochar was observed at acidic pH of 2 with 0.2 g/100 ml of adsorbent dosage and 90 mg/l of initial concentration. The equilibrium adsorption data were fitted to three isotherms, namely Langmuir, Freundlich and Temkin. Freundlich model proved to show the best suited results with value of correlation coefficient of 99.12%. Thus, the application of DB for production of biochar as potential adsorbent supports sustainability of algae biodiesel. Copyright © 2016 Elsevier Ltd. All rights reserved.

Single, binary and multi-component adsorption of some anions and heavy metals on environmentally friendly Carpobrotus edulis plant.

PubMed

Chiban, Mohamed; Soudani, Amina; Sinan, Fouad; Persin, Michel

2011-02-01

A low-cost adsorbent and environmentally friendly adsorbent from Carpobrotus edulis plant was used for the removal of NO(3)(-), H(2)PO(4)(-), Pb(2+) and Cd(2+) ions from single, binary and multi-component systems. The efficiency of the adsorbent was studied using batch adsorption technique under different experimental conditions by varying parameters such as pH, initial concentration and contact time. In single component systems, the dried C. edulis has the highest affinity for Pb(2+), followed by NO(3)(-), Cd(2+) and H(2)PO(4)(-), with adsorption capacities of 175mg/g, 125mg/g, 28mg/g and 26mg/g, respectively. These results showed that the adsorption of NO(3)(-) and H(2)PO(4)(-) ions from single and binary component systems can be successfully described by Langmuir and Freundlich isotherms. Freundlich adsorption model, showed the best fit to the single and binary experimental adsorption data. These results also indicated that the adsorption yield of Pb(2+) ion was reduced by the presence of Cd(2+) ion in binary metal mixture. The competitive adsorption of NO(3)(-), H(2)PO(4)(-), Pb(2+) and Cd(2+) ions on dried C. edulis plant shows that NO(3)(-) and H(2)PO(4)(-) anions are able to adsorb on different free binding sites and Pb(2+) and Cd(2+) cations are able to adsorb on the same active sites of C. edulis particles. The dried C. edulis was found to be efficient in removing nitrate, phosphate, cadmium and lead from aqueous solution as compared to other adsorbents already used for the removal of these ions. Copyright © 2010 Elsevier B.V. All rights reserved.

Measuring and modeling surface sorption dynamics of organophosphate flame retardants in chambers

EPA Science Inventory

Understanding the sorption mechanisms for organophosphate flame retardants (OPFRs) on impervious surfaces is important to improve our understanding of the fate and transport of OPFRs in indoor environments. Langmuir and Freundlich models are widely adopted to describe sorption be...

Apiaceae Family Plants as Low-Cost Adsorbents for the Removal of Lead Ion from Water Environment

NASA Astrophysics Data System (ADS)

Boontham, W.; Babel, S.

2017-06-01

Adsorbents prepared from the three selected plants from Apiaceae famaily commonly known as parsley, coriander and culantro were observed to remove lead from aqueous solutions. Batch experiments were conducted to study the effect of dosage, pH, contact time and agitation speed at 10 mg L-1 initial Pb(II) concentration. Results revealed that three selected plants showed high adsorption capacity for removal of lead from aqueous solutions. The maximum biosorption of Pb2+ was found to be more than 97% with 1.0 g/l dosage for all three adsorbents under optimum pH of 3-5. The adsorption equilibrium was established after about 1 hr. The equilibrium adsorption capacity of parsley and coriander were found to fit well with the Langmuir isotherm whereas the Freundlich isotherm was better fit for culantro. The studies showed that the adsorbents can be used for removing lead ions from contaminated waters.

Adsorptive removal of pharmaceuticals from water by commercial and waste-based carbons.

PubMed

Calisto, Vânia; Ferreira, Catarina I A; Oliveira, João A B P; Otero, Marta; Esteves, Valdemar I

2015-04-01

This work describes the single adsorption of seven pharmaceuticals (carbamazepine, oxazepam, sulfamethoxazole, piroxicam, cetirizine, venlafaxine and paroxetine) from water onto a commercially available activated carbon and a non-activated carbon produced by pyrolysis of primary paper mill sludge. Kinetics and equilibrium adsorption studies were performed using a batch experimental approach. For all pharmaceuticals, both carbons presented fast kinetics (equilibrium times varying from less than 5 min to 120 min), mainly described by a pseudo-second order model. Equilibrium data were appropriately described by the Langmuir and Freundlich isotherm models, the last one giving slightly higher correlation coefficients. The fitted parameters obtained for both models were quite different for the seven pharmaceuticals under study. In order to evaluate the influence of water solubility, log Kow, pKa, polar surface area and number of hydrogen bond acceptors of pharmaceuticals on the adsorption parameters, multiple linear regression analysis was performed. The variability is mainly due to log Kow followed by water solubility, in the case of the waste-based carbon, and due to water solubility in the case of the commercial activated carbon. Copyright © 2015 Elsevier Ltd. All rights reserved.

Genetic characterization, nickel tolerance, biosorption, kinetics, and uptake mechanism of a bacterium isolated from electroplating industrial effluent.

PubMed

Nagarajan, N; Gunasekaran, P; Rajendran, P

2015-04-01

Electroplating industries in Madurai city produce approximately 49,000 L of wastewater and 1200 L of sludge every day revealing 687-5569 ppm of nickel (Ni) with other contaminants. Seventeen Ni-tolerant bacterial strains were isolated from nutrient-enriched effluents. Among them one hyper Ni accumulating strain was scored and identified as Bacillus cereus VP17 on the basis of morphology, biochemical tests, 16S rDNA gene sequencing, and phylogenetic analysis. Equilibrium data of Ni(II) ions using the bacterium as sorbent at isothermal conditions (37 °C) and pH 6 were best adjusted by Langmuir (R(2) = 0.6268) and Freundlich models (R(2) = 0.9505). Experimental validation reveals Ni sorption takes place on a heterogeneous surface of the biosorbent, and predicted metal sorption capacity is 434 ppm. The pseudo-second-order kinetic model fitted the biosorption kinetic data better than the pseudo-first-order kinetic model (R(2) = 0.9963 and 0.3625). Scanning electron microscopy, energy dispersive X-ray, and Fourier transform infrared spectroscopy studies of the bacterial strain with and without Ni(II) ion reveals the biosorption mechanism. The results conclude possibilities of using B. cereus VP17 for Ni bioremediation.

Removal of hexavalent chromium by using red mud activated with cetyltrimethylammonium bromide.

PubMed

Li, Deliang; Ding, Ying; Li, Lingling; Chang, Zhixian; Rao, Zhengyong; Lu, Ling

2015-01-01

The removal of hexavalent chromium [Cr(VI)] from aqueous solution by using red mud activated with cetyltrimethylammonium bromide (CTAB) was studied. The optimum operation parameters, such as CTAB concentration, pH values, contact time, and initial Cr(VI) concentration, were investigated. The best concentration of CTAB for modifying red mud was found to be 0.50% (mCTAB/VHCl,0.6 mol/L). The lower pH (<2) was found to be much more favourable for the removal of Cr(VI). Red mud activated with CTAB can greatly improve the removal ratio of Cr(VI) as high as four times than that of original red mud. Adsorption equilibrium was reached within 30 min under the initial Cr(VI) concentration of 100 mg L(-1). The isotherm data were analysed using Langmuir and Freundlich models. The adsorption of Cr(VI) on activated red mud fitted well to the Langmuir isotherm model, and the maximum adsorption capacity was estimated as 22.20 mg g(-1) (Cr/red mud). The adsorption process could be well described using the pseudo-second-order model. The result shows that activated red mud is a promising agent for low-cost water treatment.

Investigation of adsorption of Rhodamine B onto a natural adsorbent Argemone mexicana.

PubMed

Khamparia, Shraddha; Jaspal, Dipika

2016-12-01

The present study aims at exploring the potential of the seeds of a tropical weed, Argemone mexicana (AM), for the removal of a toxic xanthene textile dye, Rhodamine B (RHB), from waste water. Impact of pH, adsorbent dosage, particle size, contact time and dye concentration have been assessed during adsorption. The weed has been well characterized by several latest techniques thereby providing an indepth information of the mechanism during adsorption. About 80% removal has been attained with 0.06 g of adsorbent over the studied system. Thermodynamic and kinetic studies, followed by second order kinetic model, directed towards the endothermic nature of adsorption. The results obtained from batch experiments were modelled using Langmuir and Freundlich isotherm and were analysed on the basis of R 2 and six error functions for selection of appropriate model. Langmuir isotherm was found to be best fitted to the experimental data with high values of R 2 and lower values of error functions. Adsorption study revealed the affinity of AM seeds for the dye ions present in waste water, introducing a novel adsorbent in field of waste water treatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Rapid removal of bisphenol A on highly ordered mesoporous carbon.

PubMed

Sui, Qian; Huang, Jun; Liu, Yousong; Chang, Xiaofeng; Ji, Guangbin; Deng, Shubo; Xie, Tao; Yu, Gang

2011-01-01

Bisphenol A (BPA) is of global concern due to its disruption of endocrine systems and ubiquity in the aquatic environment. It is important, therefore, that efforts are made to remove it from the aqueous phase. A novel adsorbent, mesoporous carbon CMK-3, prepared from hexagonal SBA-15 mesoporous silica was studied for BPA removal from aqueous phase, and compared with conventional powdered activated carbon (PAC). Characterization of CMK-3 by transmission electron microscopy (TEM), X-ray diffraction, and nitrogen adsorption indicated that prepared CMK-3 had an ordered mesoporous structure with a high specific surface area of 920 m2/g and a pore-size of about 4.9 nm. The adsorption of BPA on CMK-3 followed a pseudo second-order kinetic model. The kinetic constant was 0.00049 g/(mg x min), much higher than the adsorption of BPA on PAC. The adsorption isotherm fitted slightly better with the Freundlich model than the Langmuir model, and adsorption capacity decreased as temperature increased from 10 to 40 degrees C. No significant influence of pH on adsorption was observed at pH 3 to 9; however, adsorption capacity decreased dramatically from pH 9 to 13.

Removal of ammonium ion from water by Na-rich birnessite: Performance and mechanisms.

PubMed

Cheng, Ya; Huang, Tinglin; Shi, Xinxin; Wen, Gang; Sun, Yuankui

2017-07-01

Na-rich birnessite (NRB) was synthesized by a simple synthesis method and used as a high-efficiency adsorbent for the removal of ammonium ion (NH 4 + ) from aqueous solution. In order to demonstrate the adsorption performance of the synthesized material, the effects of contact time, pH, initial ammonium ion concentration, and temperature were investigated. Adsorption kinetics showed that the adsorption behavior followed the pseudo second-order kinetic model. The equilibrium adsorption data were fitted to Langmuir and Freundlich adsorption models and the model parameters were evaluated. The monolayer adsorption capacity of the adsorbent, as obtained from the Langmuir isotherm, was 22.61mg NH 4 + -N/g at 283K. Thermodynamic analyses showed that the adsorption was spontaneous and that it was also a physisorption process. Our data revealed that the higher NH 4 + adsorption capacity could be primarily attributed to the water absorption process and electrostatic interaction. Particularly, the high surface hydroxyl-content of NRB enables strong interactions with ammonium ion. The results obtained in this study illustrate that the NRB is expected to be an effective and economically viable adsorbent for ammonium ion removal from aqueous system. Copyright © 2016. Published by Elsevier B.V.

Effects of laser ablated silver nanoparticles on Lemna minor.

PubMed

Üçüncü, Esra; Özkan, Alper D; Kurşungöz, Canan; Ülger, Zeynep E; Ölmez, Tolga T; Tekinay, Turgay; Ortaç, Bülend; Tunca, Evren

2014-08-01

The present study investigates and models the effect of laser ablated silver nanoparticles (AgNPs) on the development of the aquatic macrophyte Lemna minor. Toxic effects of five different AgNP concentrations (8, 16, 32, 96 and 128 μg L(-1)) on L. minor were recorded over seven days under simulated natural conditions. Biosorption of AgNPs by L. minor was modeled using four sorption isotherms, and the sorption behavior was found to agree most closely with the Langmuir-Freundlich model (R(2)=0.997). While toxic effects of AgNPs could be observed in all models and concentrations, the greatest increase in toxicity was in the 8-32 μg L(-1) range. Dry weight- and frond number-based inhibition experiments suggest that growth inhibition does not necessarily scale with AgNP concentration, and that slight fluctuations in inhibition rates exist over certain concentration ranges. Very close fits (R(2)=0.999) were obtained for all removal models, suggesting that the fluctuations are not caused by experimental variation. In addition, L. minor was found to be a successful bioremediation agent for AgNPs, and displayed higher removal rates for increasing AgNP doses. FT-IR spectroscopy suggests that carbonyl groups are involved in AgNP remediation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Removal of Trace Arsenic to Meet Drinking Water Standards Using Iron Oxide Coated Multiwall Carbon Nanotubes.

PubMed

Ntim, Susana Addo; Mitra, Somenath

2011-05-12

This study presents the removal of trace level arsenic to meet drinking water standards using an iron oxide-multi-walled carbon nanotube (Fe-MWCNT) hybrid as a sorbent. The synthesis was facilitated by the high degree of nanotube functionalization using a microwave assisted process, and a controlled assembly of iron oxide was possible where the MWCNT served as an effective support for the oxide. In the final product, 11 % of the carbon atoms were attached to Fe. The Fe-MWCNT was effective in arsenic removal to below the drinking water standard levels of 10 µg L(-1). The absorption capacity of the composite was 1723 µg g(-1) and 189 µg g(-1) for As(III) and As(V) respectively. The adsorption of As(V) on Fe-MWCNT was faster than that of As(III). The pseudo-second order rate equation was found to effectively describe the kinetics of arsenic adsorption. The adsorption isotherms for As(III) and As(V) fitted both the Langmuir and Freundlich models.

Adsorption of arsenic on multiwall carbon nanotube-zirconia nanohybrid for potential drinking water purification.

PubMed

Ntim, Susana Addo; Mitra, Somenath

2012-06-01

The adsorptive removal of arsenic from water using a multiwall carbon nanotube-zirconia nanohybrid (MWCNT-ZrO(2)) is presented. The MWCNT-ZrO(2) with 4.85% zirconia was effective in meeting the drinking water standard levels of 10 μg L(-1). The absorption capacity of the composite were 2000 μg g(-1) and 5000 μg g(-1) for As(III) and As(V) respectively, which were significantly higher than those reported previously for iron oxide coated MWCNTs. The adsorption of As(V) on MWCNT-ZrO(2) was faster than that of As(III), and a pseudo-second order rate equation effectively described the uptake kinetics. The adsorption isotherms for As(III) and As(V) fitted both the Langmuir and Freundlich models. A major advantage of the MWCNT-ZrO(2) was that the adsorption capacity was not a function of pH. Copyright © 2012 Elsevier Inc. All rights reserved.

Study on the sorption behaviour of estrone on marine sediments.

PubMed

Zhang, Jing; Yang, Gui-Peng; Li, Quan; Cao, Xiaoyan; Liu, Guangxing

2013-11-15

The sorption behaviour of estrone (E1) on marine sediments treated by different methods was systematically investigated. About 22 h was required for sorption equilibrium of E1. Sorption isotherms of E1 were well fitted with Freundlich model. The sorption behaviour of E1 on HCl-treatment and H2O-treatment sediments related significantly with the sediment organic carbon contents. Additionally, clay minerals and surface areas of sediments played dominant roles in the sorption of E1 on H2O2-treatment sediments. Some external factors which could affect sorption behaviour of E1 were also investigated. Our results showed that the sorption capacity of E1 on the sediments increased with the increasing concentrations of cationic surfactant cetyltrimethylammonium bromide (CTAB), nonionic surfactant polyoxyethylene (80) sorbitan esters (Tween 80) and salinity of seawater. In contrast, the sorption capacity of E1 decreased with the increasing concentration of anionic surfactant sodium dodecylbenzene sulfonate (SDBS), pH value and temperature of seawater. Copyright © 2013 Elsevier Ltd. All rights reserved.

Removal of ammonium from aqueous solutions with volcanic tuff.

PubMed

Marañón, E; Ulmanu, M; Fernández, Y; Anger, I; Castrillón, L

2006-10-11

This paper presents kinetic and equilibrium data concerning ammonium ion uptake from aqueous solutions using Romanian volcanic tuff. The influence of contact time, pH, ammonium concentration, presence of other cations and anion species is discussed. Equilibrium isotherms adequately fit the Langmuir and Freundlich models. The results showed a contact time of 3h to be sufficient to reach equilibrium and pH of 7 to be the optimum value. Adsorption capacities of 19 mg NH(4)(+)/g were obtained in multicomponent solutions (containing NH(4)(+), Zn(2+), Cd(2+), Ca(2+), Na(2+)). The presence of Zn and Cd at low concentrations did not decrease the ammonium adsorption capacity. Comparison of Romanian volcanic tuff with synthetic zeolites used for ammonium removal (5A, 13X and ZSM-5) was carried out. The removal efficiciency of ammonium by volcanic tuff were similar to those of zeolites 5A and 13X at low initial ammonium concentration, and much higher than those of zeolite ZSM-5.

A novel biodegradable β-cyclodextrin-based hydrogel for the removal of heavy metal ions.

PubMed

Huang, Zhanhua; Wu, Qinglin; Liu, Shouxin; Liu, Tian; Zhang, Bin

2013-09-12

A novel biodegradable β-cyclodextrin-based gel (CAM) was prepared and applied to the removal of Cd(2+), Pb(2+) and Cu(2+) ions from aqueous solutions. CAM hydrogel has a typical three-dimensional network structure, and showed excellent capability for the removal of heavy metal ions. The effect of different experimental parameters, such as initial pH, adsorbent dosage and initial metal ion concentration, were investigated. The adsorption isotherm data fitted well to the Freundlich model. The adsorption capacity was in the order Pb(2+)>Cu(2+)>Cd(2+) under the same experimental conditions. The maximum adsorption capacities for the metal ions in terms of mg/g of dry gel were 210.6 for Pb(2+), 116.41 for Cu(2+), and 98.88 for Cd(2+). The biodegradation efficiency of the resin reached 79.4% for Gloeophyllum trabeum. The high adsorption capacity and kinetics results indicate that CAM can be used as an alternative adsorbent to remove heavy metals from aqueous solution. Published by Elsevier Ltd.

Treatment of aqueous diethyl phthalate by adsorption using a functional polymer resin.

PubMed

Xu, Zhengwen; Zhang, Weiming; Pan, Bingcai; Lv, Lu; Jiang, Zhengmao

2011-01-01

To study the adsorptive separation efficiency, adsorption and desorption performances of diethyl phthalate (DEP) were investigated with a functional polymer resin (NDA-702). A macroporous polymer resin (XAD-4) and a coal-based granular activated carbon (AC-750) were chosen for comparison. The kinetic adsorption data obeyed the pseudo-second-order rate model, and the adsorption processes were limited by both film and intraparticle diffusions. Adsorption equilibrium data were well fitted by the Freundlich equation, and the larger uptake and higher selection of NDA-702 than AC-750 and XAD-4 was probably due to the microporous structure, phenyl rings and polar groups on NDA-702. Thermodynamic adsorption studies indicated that the test adsorbents spontaneously adsorbed DEP, driven mainly by enthalpy change. Continuous fixed-bed runs demonstrated that there no significant loss of the resin's adsorption capacity and there was complete regeneration of NDA-702. The results suggest that NDA-702 has excellent potential as an adsorption material for water treatment.

Silica adsorbent prepared from spent diatomaceous earth and its application to removal of dye from aqueous solution.

PubMed

Tsai, W T; Hsien, K J; Yang, J M

2004-07-15

The objective of this work is to study the activation regeneration of spent diatomaceous earth (SDE) for the preparation of silica adsorbents using thermal regeneration and acid/alkaline activation methods. Under the experimental conditions investigated, it was found that the alkaline activation method carried out by sodium hydroxide under controlled conditions is significantly superior to other heat and activation methods. The porosities of solids thus obtained are over 0.2, indicating that they are basically mesoporous. The optimal porous material thus prepared was used as a mineral adsorbent for methylene blue at 25 degrees C. The adsorption equilibrium revealed that the silica adsorbent can take up over 50 mg/g at relatively low concentrations in aqueous medium from the fittings of Langmuir and Freundlich isotherms with high correlations. On the other hand, the adsorption kinetic of methylene blue under various adsorbent dosages can be well described with a pseudo-second-order reaction model. Copyright 2004 Elsevier Inc.

Characteristics of activated carbon and carbon nanotubes as adsorbents to remove annatto (norbixin) in cheese whey.

PubMed

Zhang, Yue; Pan, Kang; Zhong, Qixin

2013-09-25

Removing annatto from cheese whey without bleaching has potential to improve whey protein quality. In this work, the potential of two activated carbon products and multiwalled carbon nanotubes (CNT) was studied for extracting annatto (norbixin) in aqueous solutions. Batch adsorption experiments were studied for the effects of solution pH, adsorbent mass, contact duration, and ionic strength. The equilibrium adsorption data were observed to fit both Langmuir and Freundlich isotherm models. The thermodynamic parameters estimated from adsorption isotherms demonstrated that the adsorption of norbixin on three adsorbents is exothermic, and the entropic contribution differs with adsorbent structure. The adsorption kinetics, with CNT showing a higher rate than activated carbon, followed the pseudo first order and second order rate expressions and demonstrated the significance of intraparticle diffusion. Electrostatic interactions were observed to be significant in the adsorption. The established adsorption parameters may be used in the dairy industry to decolorize cheese whey without applying bleaching agents.

Column performance of carbon nanotube packed bed for methylene blue and orange red dye removal from waste water

NASA Astrophysics Data System (ADS)

Gill, G. K.; Mubarak, N. M.; Nizamuddin, S.; Al-Salim, H. S.; Sahu, J. N.

2017-06-01

Environmental issues have always been a major issue among human kind for the past decades. As the time passes by, the technology field has grown and has helped a lot in order to reduce these environmental issues. Industries such as metal plating facilities, mining operations and batteries production are a few examples that involves in the environmental issues. Carbon nanotube is proven to possess excellent adsorption capacity for the removal of methylene blue and orange red dyes. The effect of process parameters such as pH and contact time was investigated The results revealed that optimized conditions for the highest removal for methylene blue (MB) (97%) and orange red (94%) are at pH 10, CNTs dosage of 1 grams, and 15 minutes for each dyes removal respectively. The equilibrium adsorption data obtained was best fit to Freundlich model, while kinetic data can be characterized by the pseudo second-order rate kinetics.

Properties comparison of biochars from corn straw with different pretreatment and sorption behaviour of atrazine.

PubMed

Zhao, Xuchen; Ouyang, Wei; Hao, Fanghua; Lin, Chunye; Wang, Fangli; Han, Sheng; Geng, Xiaojun

2013-11-01

Biochar has been recognised as an efficient pollution control material. In this study, biochars (CS450 and ADPCS450) were produced using corn straw with different pretreatment techniques (without and with ammonium dihydrogen phosphate (ADP)). The character of the two biochars was compared using elemental analysis, specific surface area (SSA) and Fourier transform infrared spectra (FTIR). ADPCS450 had a higher residue yield and a much larger specific surface area than CS450. The Freundlich, Langmuir and Redlich-Peterson models were used to interpret the sorption behaviour of atrazine (2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine), and the results fit the Redlich-Peterson equation best. The isothermal sorption parameters indicated that the sorption capacity of atrazine on ADPCS450 was much larger than the sorption capacity of atrazine on CS450. Atrazine sorption was also favoured in acidic solution and under higher temperature conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Adsorption and biodegradation of antidiabetic pharmaceuticals in soils.

PubMed

Mrozik, Wojciech; Stefańska, Justyna

2014-01-01

Pharmaceuticals are emerging contaminants in the natural environment. Most studies of the environmental fate of these chemicals focus on their behavior in wastewater treatment processes and in sewage sludge. Little is known about their behavior in soils. In this study adsorption and biodegradation of four antidiabetic pharmaceuticals - glimepiride, glibenclamide, gliclazide and metformin - were examined in three natural soils. The sorption of sulfonylurea derivatives was high (higher than sulfonylurea herbicides for example), whereas metformin showed high mobility. Desorption rates were highest for metformin. Sorption isotherms in two of three soils fitted best to the Freundlich model. Despite their high affinity to for soil surfaces, biodegradation studies revealed that transformation of the drugs occurred. Biodegradation results were described by pseudo-first order kinetics with half-life values from 5 to over 120 d (under aerobic conditions) and indicate that none of the tested drugs can be classified as quickly biodegradable. Biodegradation under anoxic conditions was much slower; often degrading by less than 50% during time of the experiment. Copyright © 2013 Elsevier Ltd. All rights reserved.

Phenanthrene binding by humic acid-protein complexes as studied by passive dosing technique.

PubMed

Zhao, Jian; Wang, Zhenyu; Ghosh, Saikat; Xing, Baoshan

2014-01-01

This work investigated the binding behavior of phenanthrene by humic acids (HA-2 and HA-5), proteins (bovine serum albumin (BSA)), lysozyme and pepsin), and their complexes using a passive dosing technique. All sorption isotherms were fitted well with Freundlich model and the binding capability followed an order of HA-5 > HA-2 > BSA > pepsin > lysozyme. In NaCl solution, phenanthrene binding to HA-BSA complexes was much higher than the sum of binding to individual HA and BSA, while there was no enhancement for HA-pepsin. Positively charged lysozyme slightly lowered phenanthrene binding on both HAs due to strong aggregation of HA-lysozyme complexes, leading to reduction in the number of binding sites. The binding enhancement by HA-BSA was observed under all tested ion species and ionic strengths. This enhancement can be explained by unfolding of protein, reduction of aggregate size and formation of HA-BSA complexes with favorable conformations for binding phenanthrene. Copyright © 2013 Elsevier Ltd. All rights reserved.

Removal of hexavalent chromium from wastewater using a new composite chitosan biosorbent.

PubMed

Boddu, Veera M; Abburi, Krishnaiah; Talbott, Jonathan L; Smith, Edgar D

2003-10-01

A new composite chitosan biosorbent was prepared by coating chitosan, a glucosamine biopolymer, onto ceramic alumina. The composite bioadsorbent was characterized by high-temperature pyrolysis, porosimetry, scanning electron microscopy, and X-ray photoelectron spectroscopy. Batch isothermal equilibrium and continuous column adsorption experiments were conducted at 25 degrees C to evaluate the biosorbent for the removal of hexavalent chromium from synthetic as well as field samples obtained from chrome plating facilities. The effect of pH, sulfate, and chloride ion on adsorption was also investigated. The biosorbent loaded with Cr(VI) was regenerated using 0.1 M sodium hydroxide solution. A comparison of the results of the present investigation with those reported in the literature showed that chitosan coated on alumina exhibits greater adsorption capacity for chromium(VI). Further, experimental equilibrium data were fitted to Langmuir and Freundlich adsorption isotherms, and values of the parameters of the isotherms are reported. The ultimate capacity obtained from the Langmuir model is 153.85 mg/g chitosan.

Ammonium Removal from Aqueous Solutions by Clinoptilolite: Determination of Isotherm and Thermodynamic Parameters and Comparison of Kinetics by the Double Exponential Model and Conventional Kinetic Models

PubMed Central

Tosun, İsmail

2012-01-01

The adsorption isotherm, the adsorption kinetics, and the thermodynamic parameters of ammonium removal from aqueous solution by using clinoptilolite in aqueous solution was investigated in this study. Experimental data obtained from batch equilibrium tests have been analyzed by four two-parameter (Freundlich, Langmuir, Tempkin and Dubinin-Radushkevich (D-R)) and four three-parameter (Redlich-Peterson (R-P), Sips, Toth and Khan) isotherm models. D-R and R-P isotherms were the models that best fitted to experimental data over the other two- and three-parameter models applied. The adsorption energy (E) from the D-R isotherm was found to be approximately 7 kJ/mol for the ammonium-clinoptilolite system, thereby indicating that ammonium is adsorbed on clinoptilolite by physisorption. Kinetic parameters were determined by analyzing the nth-order kinetic model, the modified second-order model and the double exponential model, and each model resulted in a coefficient of determination (R2) of above 0.989 with an average relative error lower than 5%. A Double Exponential Model (DEM) showed that the adsorption process develops in two stages as rapid and slow phase. Changes in standard free energy (∆G°), enthalpy (∆H°) and entropy (∆S°) of ammonium-clinoptilolite system were estimated by using the thermodynamic equilibrium coefficients. PMID:22690177

Ammonium removal from aqueous solutions by clinoptilolite: determination of isotherm and thermodynamic parameters and comparison of kinetics by the double exponential model and conventional kinetic models.

PubMed

Tosun, Ismail

2012-03-01

The adsorption isotherm, the adsorption kinetics, and the thermodynamic parameters of ammonium removal from aqueous solution by using clinoptilolite in aqueous solution was investigated in this study. Experimental data obtained from batch equilibrium tests have been analyzed by four two-parameter (Freundlich, Langmuir, Tempkin and Dubinin-Radushkevich (D-R)) and four three-parameter (Redlich-Peterson (R-P), Sips, Toth and Khan) isotherm models. D-R and R-P isotherms were the models that best fitted to experimental data over the other two- and three-parameter models applied. The adsorption energy (E) from the D-R isotherm was found to be approximately 7 kJ/mol for the ammonium-clinoptilolite system, thereby indicating that ammonium is adsorbed on clinoptilolite by physisorption. Kinetic parameters were determined by analyzing the nth-order kinetic model, the modified second-order model and the double exponential model, and each model resulted in a coefficient of determination (R(2)) of above 0.989 with an average relative error lower than 5%. A Double Exponential Model (DEM) showed that the adsorption process develops in two stages as rapid and slow phase. Changes in standard free energy (∆G°), enthalpy (∆H°) and entropy (∆S°) of ammonium-clinoptilolite system were estimated by using the thermodynamic equilibrium coefficients.

Measuring and Modeling Surface Sorption Dynamics of Organophosphate Flame Retardants in Chambers

EPA Science Inventory

Understanding the sorption mechanisms for organophosphate flame retardants (OPFRs) on impervious surfaces is important if we are to improve our understanding of the fate and transport of OPFRs in indoor environments. Traditional Langmuir and Freundlich models are widely adopted t...

Study of the Kinetics and Equilibrium of the Adsorption of Oils onto Hydrophobic Jute Fiber Modified via the Sol-Gel Method.

PubMed

Lv, Na; Wang, Xiaoli; Peng, Shitao; Zhang, Huaqin; Luo, Lei

2018-05-12

A new kind of hydrophobic and oil sorbent based on jute fiber was successfully prepared by the integration of silica onto a fiber surface via the sol-gel method and subsequent hydrophobic modification with octadecyltrichlorosilane (OTS). Compared with the hydrophilic raw fiber, the modified fiber had a water contact angle (CA) of 136.2°, suggesting that the material has good hydrophobicity. Furthermore, the ability of oil in the oil/water system (taking diesel for example) to absorb was revealed by the kinetics, the isotherm equation, and the thermodynamic parameters. Adsorption behavior was kinetically investigated using pseudo first-order and pseudo second-order models. The data mostly correlated with the pseudo first-order model. The equilibrium adsorption at 298 K was assessed by using the Langmuir and Freundlich isotherm models. The Freundlich model had greater consistency with the experimental data. The obtained thermodynamic parameters demonstrate that the adsorption of diesel is spontaneous, favorable, and exothermic.

Removal of sulfa drugs by sewage treatment in aqueous solution systems: activated carbon treatment and ozone oxidation.

PubMed

Ogata, Fumihiko; Tominaga, Hisato; Kangawa, Moe; Inoue, Kenji; Kawasaki, Naohito

2012-01-01

This study investigates the activated carbon (AC) treatment and ozone oxidation of the sulfa drugs--sulfamethoxazole (SMX), sulfamonomethoxine (SMM), sulfadimidine (SDD), and sulfadimethoxine (SDM)--in aqueous solution systems. Three AC samples were prepared from Shirasagi (AC1 and AC2) and coal (AC3), and the surface functional groups, solution pH, specific surface areas, pore volumes, and morphologies of the three samples were evaluated. The specific surface areas were in the following order: AC1 (1391 m²/g) > AC2 (1053 m²/g) > AC3 (807 m²/g). The pore volume and mean pore diameter of AC3 were greater than those of AC1 and AC2. The concentration of sulfa drugs adsorbed onto the AC samples reached equilibrium within 150 h. Experimental data of the adsorption rate were fitted to a pseudo-second-order model. The amount of sulfa drugs adsorbed onto the AC samples was in the order of SDM < SMM < SDD < SMX; the mechanism of adsorption of the sulfa drugs onto the AC samples depended on the hydrophobicity of the AC surface. The adsorption isotherm data were fitted to Freundlich and Langmuir models. Ozone was generated from oxygen gas using an A-27 ozone generator, and the complete degradation of the sulfa drugs by ozone treatment at 60 mL/min was achieved within 50 min. Ozone treatment caused the structure of the sulfa drugs to decompose via ozone oxidation.

Removal of heavy metal ions from aqueous solution using Fe3O4-SiO2-poly(1,2-diaminobenzene) core-shell sub-micron particles.

PubMed

Zhang, Fan; Lan, Jing; Zhao, Zongshan; Yang, Ye; Tan, Ruiqin; Song, Weijie

2012-12-01

In this work, Fe(3)O(4)-SiO(2)-poly(1,2-diaminobenzene) sub-micron particles (FSPs) with high saturated magnetization of ∼60-70 emu/g were developed and utilized for the removal of As(III), Cu(II), and Cr(III) ions from aqueous solution. The isothermal results fitted well with the Freundlich model and the kinetic results fitted well with the two-site pseudo-second-order model, which indicated that multilayer adsorption of As(III), Cu(II), and Cr(III) ions on FSPs occurred at two sites with different energy of adsorption. The maximum adsorption capacities followed the order of As(III) (84±5 mg/g, pH=6.0)>Cr(III) (77±3 mg/g, pH=5.3)>Cu(II) (65±3 mg/g, pH=6.0). And the chelating interaction was considered as the main adsorption mechanism. The as-prepared materials were chemically stable with low leaching of Fe (≤1.7 wt.%) and poly(1,2-diaminobenzene) (≤4.9 wt.%) in tap water, sea water, and acidic/basic solutions. These metal-loaded FSPs could be easily recovered from aqueous solutions using a permanent magnet within 20s. They could also be easily regenerated with acid. The present work indicates that the FSPs are promising for removal of heavy metal ions in field application. Copyright © 2012 Elsevier Inc. All rights reserved.

Laboratory study on metal attenuation capacity of fine grained soil near ash pond site.

PubMed

Ghosh, Sudipta; Mukherjee, Somnath; Sarkar, Sujoy; Kumar, Sunil

2008-10-01

Waste settling tanks of earthen containment nature are common in India for disposal of solid waste in slurry form. For a large pond system, e.g. ash slurry disposal tank of coal base thermal power plant, leachate generation and its migration pose a serious problem. A natural attenuation of controlling the migratory leachate is to use locally available clay material as lining system due to the adsorption properties of soil for reducing some metallic ions. The present investigation was carried out to explore the Ni2+ and Cr6+ removal capacity of surrounding soil of the ash pond site of Super Thermal Power Plant in West Bengal, India through some laboratory scale and field studies. The soil and water samples collected from the site showed the existence of Ni2+ and Cr6+ in excess to permissible limit. A two-dimensional adsorption behaviour of these pollutants through soil was assessed. The results showed that more than 80% of nickel and 72% of chromium were found to be sorbed by the soil corresponding to initial concentrations of two ions, i.e. 1.366 mg/L and 0.76 mg/L respectively. The batch adsorption data are tested Langmuir and Freundlich isotherm models and found reasonably fit. Breakthrough adsorption study uptake also showed a good adsorption capacity of the soil. The experimental results found to fit well with the existing two dimensional (2D) mathematical models as proposed by Fetter (1999).

Kinetic evaluation of chromium(VI) sorption by water lettuce (Pistia).

PubMed

Chakraborty, Rupa; Karmakar, Sukalpa; Mukherjee, Somnath; Kumar, Sunil

2014-01-01

An investigation was performed to evaluate the uptake capacity of Pistia in living condition for adsorptive removal of chromium(VI) from spiked solution for examining a remedial measure for disposal of chrome-laden wastewater in an urban wetland system. Kinetics results show about 78% removal was achieved for 3 mg/L initial concentration of Cr(VI). Experimental data showed that the root portion absorbed more Cr(VI) (28.54 μg/g) compared to accumulation in leaf (5.73 μg/g). It was also noted that the plant could effectively remove Cr(VI) from the solution with minor damage up to an initial Cr(VI) concentration of 3 mg/L, for which the adsorption isotherm studies were conducted. The maximum uptake capacity of the plant was recorded as 0.05 mg/g of Cr(VI) at the equilibrium level after a contact period of 7 days for an initial concentration of 8 mg /L, although severe physiological damage occurred. The experimental results were plotted in Langmuir and Freundlich isotherm models and both were found to be well fitted (r(2) = 0.979 and r(2) = 0.974 respectively). The high value of n (2.16) reveals a strong bond between the plant root and dissolved Cr(VI), which favours the adsorption process. The order of the reaction was also examined on the basis of uptake capacity and it was found that the second order model fitted best.

Nanostructured Mn-Fe Binary Mixed Oxide: Synthesis, Characterization and Evaluation for Arsenic Removal.

PubMed

Pillewan, Pradnya; Mukherjee, Shrabanti; Bansiwal, Amit; Rayalu, Sadhana

2014-07-01

Adsorption of arsenic on bimetallic Mn and Fe mixed oxide was carried out using both field as well as simulated water. The material was synthesized using hydrothermal method and characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Langmuir and Freundlich adsorption isotherms were computed using batch adsorption studies to determine the adsorption capacity of Mn-Fe binary mixed oxide for arsenic. Adsorption capacity for MFBMO obtained from Freundlich model was found to be 2.048 mg/g for simulated water and 1.084 mg/g for field water. Mn-Fe binary mixed oxide was found to be effective adsorbent for removal of arsenic from water.

Comparison of ultrasonic with stirrer performance for removal of sunset yellow (SY) by activated carbon prepared from wood of orange tree: artificial neural network modeling.

PubMed

Ghaedi, A M; Ghaedi, M; Karami, P

2015-03-05

The present work focused on the removal of sunset yellow (SY) dye from aqueous solution by ultrasound-assisted adsorption and stirrer by activated carbon prepared from wood of an orange tree. Also, the artificial neural network (ANN) model was used for predicting removal (%) of SY dye based on experimental data. In this study a green approach was described for the synthesis of activated carbon prepared from wood of an orange tree and usability of it for the removal of sunset yellow. This material was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The impact of variables, including initial dye concentration (mg/L), pH, adsorbent dosage (g), sonication time (min) and temperature (°C) on SY removal were studied. Fitting the experimental equilibrium data of different isotherm models such as Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models display the suitability and applicability of the Langmuir model. Analysis of experimental adsorption data by different kinetic models including pseudo-first and second order, Elovich and intraparticle diffusion models indicate the applicability of the second-order equation model. The adsorbent (0.5g) is applicable for successful removal of SY (>98%) in short time (10min) under ultrasound condition. Copyright © 2014 Elsevier B.V. All rights reserved.

Artificial intelligence and regression analysis for Cd(II) ion biosorption from aqueous solution by Gossypium barbadense waste.

PubMed

Fawzy, Manal; Nasr, Mahmoud; Nagy, Heba; Helmi, Shacker

2018-02-01

In this study, batch biosorption experiments were conducted to determine the removal efficiency of Cd(II) ion from aqueous solutions by Gossypium barbadense waste. The biosorbent was characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) connected with energy dispersive X-ray (EDX). The sorption mechanism was described by complexation/chelation of Cd 2+ with the functional groups of O-H, C=O, -COO-, and C-O, as well as, cation-exchange with Mg 2+ and K + . At initial Cd(II) ion concentration (C o ), 50 mg/L, the adsorption equilibrium of 89.2% was achieved after 15 min under the optimum experimental factors of pH 6.0, biosorbent dosage 10 g/L, and particle diameter 0.125-0.25 mm. Both Langmuir and Freundlich models fitted well to the sorption data, suggesting the co-existence of monolayer coverage along with heterogenous surface biosorption. Artificial neural network (ANN) with a structure of 5-10-1 was performed to predict the Cd(II) ion removal efficiency. The ANN model provided high fit (R 2 0.923) to the experimental data and indicated that C o was the most influential input. A pure-quadratic model was developed to determine the effects of experimental factors on Cd(II) ion removal efficiency, which indicated the limiting nature of pH and biosorbent dosage on Cd(II) adsorption. Based on the regression model (R 2 0.873), the optimum experimental factors were pH 7.61, biosorbent dosage 24.74 g/L, particle size 0.125-0.25 mm, and adsorption time 109.77 min, achieving Cd 2+ removal of almost 100% at C o 50 mg/L.

Ammonium removal from aqueous solutions by using natural Chinese (Chende) zeolite as adsorbent.

PubMed

Huang, Haiming; Xiao, Xianming; Yan, Bo; Yang, Liping

2010-03-15

This paper presents a study of the removal of ammonium ion from aqueous solutions using natural Chinese (Chende) zeolite. A series of experiments was conducted to examine the effects of solution pH, particle size, contact time, adsorbent dosage, and the presence of other cation- and anion species on ammonium removal. The findings indicated that these parameters named had a significant effect on the removal of ammonium by the zeolite. The effect of other cations on the removal of ammonium followed the order of preference Na(+)>K(+)>Ca(2+)>Mg(2+) at identical mass concentrations, and the effect of the presence of individual anions followed the order of preference carbonate>chloride>sulfate>phosphate at identical mass concentrations of ammonium ions. Kinetic analysis showed that the adsorption of ammonium on zeolite at different ranges of particle size well followed the pseudo-second-order model and followed the intra-particle diffusion model only during the initial 60 min of the adsorption process. Equilibrium isotherm data was fitted to the linear Langmuir- and Freundlich models with the latter model providing the better description of the process (R(2)=0.991-0.997) compared to the former (R(2)=0.902-0.989). (c) 2009 Elsevier B.V. All rights reserved.

Preparation and characterization of poly(AA co PVP)/PGS composite and its application for methylene blue adsorption.

PubMed

Yang, Cai-xia; Lei, Lei; Zhou, Peng-xin; Zhang, Zhe; Lei, Zi-qiang

2015-04-01

Poly (AA co PVP)/PGS (PAPP) composite adsorbent was prepared by radical polymerization from Acrylic acid (AA), Polyvinylpyrrolidone (PVP) and Palygorskite (PGS), using N,N-methylenebisacrylamide (MBA) as cross-linker and potassium persulfate (KPS) as initiator. The PAPP was characterized with Fourier transform infrared (FT-IR), thermogravimetric analysis (TG), scanning electron microscope (SEM) and transmission electron microscopy (TEM). PAPP was used as adsorbent for the removal of methylene blue from aqueous solutions. The influences of pH, adsorption temperature and adsorption time on the adsorption properties of the composite to the dye were also investigated. Meanwhile, the adsorption rate data and adsorption equilibrium date were analyzed based on the pseudo-first-order and pseudo-second-order kinetic model, Langmuir and Freundlich isotherm models, respectively. The results indicating that the kinetic behavior better fit with the pseudo-second-order kinetic model. The maximum equilibrium adsorption capacity (q(m)) is 1815 mg/g at 289 K. The isotherm behavior can be explained by the Langmuir isotherm models. The activation energy was also evaluated for the removal of methylene blue onto PAPP. These results demonstrate that this composite material could be used as a good adsorbent for the removal of cationic dyes from wastewater. Copyright © 2014 Elsevier Inc. All rights reserved.

Simultaneous adsorption of Cd²⁺ and BPA on amphoteric surfactant activated montmorillonite.

PubMed

Liu, Chongmin; Wu, Pingxiao; Zhu, Yajie; Tran, Lytuong

2016-02-01

The study mainly investigated the simultaneous adsorption of bisphenol A (BPA) and Cd(2+) from aqueous solution on octadecane-betaine modified montmorillonite (BS-Mt). The characteristics of the obtained materials were analyzed by X-ray diffraction (XRD), Fourier-transform infrared (FTIR), Specific surface area (BET) and Scanning electron microscopy/Energy disperse spectroscopy (SEM/EDS), confirming that BS-18 was successfully introduced into Mt. Also, factors including initial solution pH, initial Cd(2+)/BPA concentration, contact time and adsorbent dosage on the adsorption processes were shown to be crucial for Cd(2+) adsorption, whereas had negligible effects on BPA adsorption. In this study, we found that pseudo-second-order model fitted well with the adsorption kinetic studies for both Cd(2+) and BPA with an equilibrium time of 24 h. The Cd(2+) and BPA adsorption isotherm could be well described by Freundlich model and Langmuir model, respectively. On the basis of kinetic models, the maximum adsorption capacity of Cd(2+) in aqueous solution was slightly enhanced after modification, indicating that Cd(2+) adsorption on BS-Mt was mainly attributed to direct electrostatic attraction and the chelate reaction, while the dramatic enhancement of maximum adsorption capacity for BPA was due to the hydrophobic interaction. Copyright © 2015 Elsevier Ltd. All rights reserved.

Eragrostis plana Nees as a novel eco-friendly adsorbent for removal of crystal violet from aqueous solutions.

PubMed

Filho, Augusto Cezar D; Mazzocato, Ana C; Dotto, Guilherme L; Thue, Pascal S; Pavan, Flávio A

2017-08-01

Eragrostis plana Nees (EPN) was used as new and eco-friendly adsorbent for the removal of crystal violet dye (CV) from aqueous solution. Specific surface area (BET), scanning electron microscopy (SEM), infrared spectroscopy (ATR-FTIR), point of zero charge (pH PZC ), and modified Boehm titration method were used to characterize the EPN material. The effects of initial pH of solution, adsorbent mass, contact time and initial dye concentration, and temperature were studied in batch adsorption mode. Kinetic data were evaluated by pseudo-first-order and pseudo-second-order models. The result exhibited that pseudo-second-order model well described the adsorption kinetics of CV onto EPN. Langmuir, Freundlich, and Sips isotherm models were used for analysis of the isothermal data. The equilibrium data of adsorption of CV onto EPN was better fitted with the Sips isotherm. Based on the Sips isotherm model, the maximum adsorption capacity was 76.20 ± 1.20 mg g -1 at 333 K. A high desorption of CV from EPN was obtained using 1.00 mol L -1 of CH 3 COOH as eluent. The thermodynamic data indicated that the adsorption was spontaneous, endothermic, and physical process. EPN can be used as alternative adsorbent to remove CV from aqueous solution.

Experimental design based response surface methodology optimization of ultrasonic assisted adsorption of safaranin O by tin sulfide nanoparticle loaded on activated carbon

NASA Astrophysics Data System (ADS)

Roosta, M.; Ghaedi, M.; Daneshfar, A.; Sahraei, R.

2014-03-01

In this research, the adsorption rate of safranine O (SO) onto tin sulfide nanoparticle loaded on activated carbon (SnS-NPAC) was accelerated by the ultrasound. SnS-NP-AC was characterized by different techniques such as SEM, XRD and UV-Vis measurements. The present results confirm that the ultrasound assisted adsorption method has remarkable ability to improve the adsorption efficiency. The influence of parameters such as the sonication time, adsorbent dosage, pH and initial SO concentration was examined and evaluated by central composite design (CCD) combined with response surface methodology (RSM) and desirability function (DF). Conducting adsorption experiments at optimal conditions set as 4 min of sonication time, 0.024 g of adsorbent, pH 7 and 18 mg L-1 SO make admit to achieve high removal percentage (98%) and high adsorption capacity (50.25 mg g-1). A good agreement between experimental and predicted data in this study was observed. The experimental equilibrium data fitting to Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich models show that the Langmuir model is a good and suitable model for evaluation and the actual behavior of adsorption. Kinetic evaluation of experimental data showed that the adsorption processes followed well pseudo-second-order and intraparticle diffusion models.

Potential immobilized Saccharomyces cerevisiae as heavy metal removal

NASA Astrophysics Data System (ADS)

Raffar, Nur Izzati Abdul; Rahman, Nadhratul Nur Ain Abdul; Alrozi, Rasyidah; Senusi, Faraziehan; Chang, Siu Hua

2015-05-01

Biosorption of copper ion using treated and untreated immobilized Saccharomyces cerevisiae from aqueous solution was investigate in this study. S.cerevisiae has been choosing as biosorbent due to low cost, easy and continuously available from various industries. In this study, the ability of treated and untreated immobilized S.cerevisiae in removing copper ion influence by the effect of pH solution, and initial concentration of copper ion with contact time. Besides, adsorption isotherm and kinetic model also studied. The result indicated that the copper ion uptake on treated and untreated immobilized S.cerevisiae was increased with increasing of contact time and initial concentration of copper ion. The optimum pH for copper ion uptake on untreated and treated immobilized S.cerevisiae at 4 and 6. From the data obtained of copper ion uptake, the adsorption isotherm was fitted well by Freundlich model for treated immobilized S.cerevisiae and Langmuir model for untreated immobilized S.cerevisiae according to high correlation coefficient. Meanwhile, the pseudo second order was described as suitable model present according to high correlation coefficient. Since the application of biosorption process has been received more attention from numerous researchers as a potential process to be applied in the industry, future study will be conducted to investigate the potential of immobilized S.cerevisiae in continuous process.

Defluoridation using biomimetically synthesized nano zirconium chitosan composite: kinetic and equilibrium studies.

PubMed

Prasad, Kumar Suranjit; Amin, Yesha; Selvaraj, Kaliaperumal

2014-07-15

The present study reports a novel approach for synthesis of Zr nanoparticles using aqueous extract of Aloe vera. Resulting nanoparticles were embedded into chitosan biopolymer and termed as CNZr composite. The composite was subjected to detailed adsorption studies for removal of fluoride from aqueous solution. The synthesized Zr nanoparticles showed UV-vis absorption peak at 420nm. TEM result showed the formation of polydispersed, nanoparticles ranging from 18nm to 42nm. SAED and XRD analysis suggested an fcc (face centered cubic) Zr crystallites. EDAX analysis suggested that Zr was an integral component of synthesized nanoparticles. FT-IR study indicated that functional group like NH, CO, CN and CC were involved in particle formation. The adsorption of fluoride on to CNZr composite worked well at pH 7.0, where ∼99% of fluoride was found to be adsorbed on adsorbent. Langmuir isotherm model best fitted the equilibrium data since it presented higher R(2) value than Freundlich model. In comparison to pseudo-first order kinetic model, the pseudo-second order model could explain adsorption kinetic behavior of F(-) onto CNZr composite satisfactorily with a good correlation coefficient. The present study revealed that CNZr composite may work as an effective tool for removal of fluoride from contaminated water. Copyright © 2014 Elsevier B.V. All rights reserved.

Batch soil adsorption and column transport studies of 2,4-dinitroanisole (DNAN) in soils

NASA Astrophysics Data System (ADS)

Arthur, Jennifer D.; Mark, Noah W.; Taylor, Susan; Šimunek, J.; Brusseau, M. L.; Dontsova, Katerina M.

2017-04-01

The explosive 2,4,6-trinitrotoluene (TNT) is currently a main ingredient in munitions; however the compound has failed to meet the new sensitivity requirements. The replacement compound being tested is 2,4-dinitroanisole (DNAN). DNAN is less sensitive to shock, high temperatures, and has good detonation characteristics. However, DNAN is more soluble than TNT, which can influence transport and fate behavior and thus bioavailability and human exposure potential. The objective of this study was to investigate the environmental fate and transport of DNAN in soil, with specific focus on sorption processes. Batch and column experiments were conducted using soils collected from military installations located across the United States. The soils were characterized for pH, electrical conductivity, specific surface area, cation exchange capacity, and organic carbon content. In the batch rate studies, change in DNAN concentration with time was evaluated using the first order equation, while adsorption isotherms were fitted using linear and Freundlich equations. Solution mass-loss rate coefficients ranged between 0.0002 h- 1 and 0.0068 h- 1. DNAN was strongly adsorbed by soils with linear adsorption coefficients ranging between 0.6 and 6.3 L g- 1, and Freundlich coefficients between 1.3 and 34 mg1 - n Ln kg- 1. Both linear and Freundlich adsorption coefficients were positively correlated with the amount of organic carbon and cation exchange capacity of the soil, indicating that similar to TNT, organic matter and clay minerals may influence adsorption of DNAN. The results of the miscible-displacement column experiments confirmed the impact of sorption on retardation of DNAN during transport. It was also shown that under flow conditions DNAN transforms readily with formation of amino transformation products, 2-ANAN and 4-ANAN. The magnitudes of retardation and transformation observed in this study result in significant attenuation potential for DNAN, which would be anticipated to contribute to a reduced risk for contamination of ground water from soil residues.

Batch soil adsorption and column transport studies of 2,4-dinitroanisole (DNAN) in soils.

PubMed

Arthur, Jennifer D; Mark, Noah W; Taylor, Susan; Šimunek, J; Brusseau, M L; Dontsova, Katerina M

2017-04-01

The explosive 2,4,6-trinitrotoluene (TNT) is currently a main ingredient in munitions; however the compound has failed to meet the new sensitivity requirements. The replacement compound being tested is 2,4-dinitroanisole (DNAN). DNAN is less sensitive to shock, high temperatures, and has good detonation characteristics. However, DNAN is more soluble than TNT, which can influence transport and fate behavior and thus bioavailability and human exposure potential. The objective of this study was to investigate the environmental fate and transport of DNAN in soil, with specific focus on sorption processes. Batch and column experiments were conducted using soils collected from military installations located across the United States. The soils were characterized for pH, electrical conductivity, specific surface area, cation exchange capacity, and organic carbon content. In the batch rate studies, change in DNAN concentration with time was evaluated using the first order equation, while adsorption isotherms were fitted using linear and Freundlich equations. Solution mass-loss rate coefficients ranged between 0.0002h -1 and 0.0068h -1 . DNAN was strongly adsorbed by soils with linear adsorption coefficients ranging between 0.6 and 6.3Lg -1 , and Freundlich coefficients between 1.3 and 34mg 1 - n L n kg -1 . Both linear and Freundlich adsorption coefficients were positively correlated with the amount of organic carbon and cation exchange capacity of the soil, indicating that similar to TNT, organic matter and clay minerals may influence adsorption of DNAN. The results of the miscible-displacement column experiments confirmed the impact of sorption on retardation of DNAN during transport. It was also shown that under flow conditions DNAN transforms readily with formation of amino transformation products, 2-ANAN and 4-ANAN. The magnitudes of retardation and transformation observed in this study result in significant attenuation potential for DNAN, which would be anticipated to contribute to a reduced risk for contamination of ground water from soil residues. Copyright © 2017 Elsevier B.V. All rights reserved.

Adsorption of anionic surfactants from aqueous solution by high content of primary amino crosslinked chitosan microspheres.

PubMed

Zhang, Caihong; Wen, Haifeng; Huang, Yingying; Shi, Wenjian

2017-04-01

High content of primary amino crosslinked chitosan microspheres (ACCMs) were synthesized and characterized with IR, XRD and SEM technologies. Subsequently, ACCMs were adopted to adsorb three common anionic surfactants from aqueous solution: sodium dodecyl benzene sulfonate (SDBS), sodium lauryl sulfate (SLS), and sodium dodecyl sulfonate (SDS). The adsorption performances were evaluated based on different variables such as the pH, contact time, temperature and initial concentration of the anionic surfactants. Moreover, the adsorption were investigated with kinetic models, equilibrium isotherms and thermodynamic models. The experimental results indicated that the adsorption processes were fitted very well with a pseudo-second-order model. The adsorption isotherms could be better described by Langmuir model rather than Freundlich model. The adsorption of SDBS was a spontaneous, exothermic process. While the adsorption of SLS and SDS were spontaneous, endothermic. The adsorption processes were complex physical-chemistry adsorption models, which are dominated by physisorption. Furthermore, this study found that the material had strong absorption abilities for anionic surfactants, the saturation adsorption capacity of ACCMs were 1220mg/g for SDBS, 888mg/g for SLS, and 825mg/g for SDS at pH 3.0 and 298K, respectively. The adsorption capacity was reduced only 5.7% after 8 cycles of the adsorption-desorption processes. Copyright © 2017 Elsevier B.V. All rights reserved.

Sorption of perfluorooctanoic acid, perfluorooctane sulfonate and perfluoroheptanoic acid on granular activated carbon.

PubMed

Zhang, Di; Luo, Qi; Gao, Bin; Chiang, Sheau-Yun Dora; Woodward, David; Huang, Qingguo

2016-02-01

The sorption of perfluorooctane sulfonate (PFOS), perfluorooctanoic acid (PFOA), and perfluoroheptanoic acid (PFHpA) on granular activated carbon (GAC) was characterized and compared to explore the underlying mechanisms. Sorption of the three perfluoroalkyl acids (PFAAs) on GAC appeared to be a rapid intra-particle diffusion process, which were well represented by the pseudo-second-order rate model with the sorption rate following the order PFOS > PFOA > PFHpA. Sorption isotherm data were well fitted by the Freundlich model with the sorption capacity (Kf) of PFOS, PFOA and PFHpA being 4.45, 2.42 and 1.66 respectively. This suggests that the hydrophilic head group on PFAAs, i.e. sulfonate vs carboxylic, has a strong influence on their sorption. Comparison between PFOA and PFHpA revealed that hydrophobicity could also play a role in the sorption of PFAAs on GAC when the fluorocarbon chain length is different. Analyses using Attenuated Total Reflection (ATR)-Fourier Transform Infrared (FTIR) spectroscopy suggested possible formation of a negative charge-assisted H-bond between PFAAs and the functionalities on GAC surfaces, including non-aromatic ketones, sulfides, and halogenated hydrocarbons. Copyright © 2015 Elsevier Ltd. All rights reserved.

Selective Adsorption and Separation of Organic Dyes with Spherical Polyelectrolyte Brushes and Compressed Carbon Dioxide.

PubMed

Zhang, Rui; Yu, Zhenchuan; Wang, Lei; Shen, Qizhe; Hou, Xiaoyan; Guo, Xuhong; Wang, Junwei; Zhu, Xuedong; Yao, Yuan

2017-10-04

Dye-containing wastewater has caused serious environmental pollution. Herein, rationally designed spherical polyelectrolyte brushes (SPBs) with cationic charges, polystyrene-poly(2-aminoethylmethacrylate hydrochloride) (PS-PAEMH) as the absorbent, and compressed carbon dioxide as the antisolvent are proposed for the separation of the anionic dye eosin Y (EY) from a solution of mixed dyes. The adsorption behavior of EY onto PS-PAEMH was highly dependent on CO 2 pressure, contact time, and initial concentration. The maximum adsorption capacity of PS-PAEMH was 335.20 mg g -1 . FTIR and UV/Vis measurements proved that the electrostatic interactions between EY and PS-PAEMH played an important role in the absorbance process. The adsorption process fitted the pseudo-second-order kinetic model and Freundlich isotherm model very well. The combined dye and polymer brush could be easily separated through ion exchange by adding an aqueous solution of NaCl. Recovered PS-PAEMH retained a high adsorption capacity even after ten cycles of regeneration. This method provides a simple and effective way to separate ionic materials for environmental engineering. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preparation of wheat straw based superabsorbent resins and their applications as adsorbents for ammonium and phosphate removal.

PubMed

Liu, Jia; Su, Yuan; Li, Qian; Yue, Qinyan; Gao, Baoyu

2013-09-01

A novel wheat straw cellulose-g-poly (potassium acrylate)/polyvinyl alcohol (WSC-g-PKA/PVA) semi-interpenetrating polymer networks (semi-IPNs) superabsorbent resin (SAR) was prepared by graft copolymerization. The structure and performance of the WSC-g-PKA/PVA semi-IPNs SAR was studied and compared with those of wheat straw cellulose-g-poly (potassium acrylate) (WSC-g-PKA) SAR. The effects of various experimental parameters such as solution pH, concentration, contact time and ion strength on NH4(+) and PO4(3-) removal from solutions were investigated. Equilibrium isotherm data of adsorption of both NH4(+) and PO4(3-) were well fitted to the Freundlich model. Kinetic analysis showed that the pseudo-second-order kinetic model was more suitable for describing the whole adsorption process of NH4(+) and PO4(3-) on SARs. Overall, WSC-g-PKA/PVA semi-IPNs SAR showed better properties in comparison with WSC-g-PKA SAR and it could be considered as one efficient material for the removal and recovery of nitrogen and phosphorus with the agronomic reuse as a fertilizer. Copyright © 2013 Elsevier Ltd. All rights reserved.

Polyvinyl alcohol-based nanocomposite hydrogels containing magnetic laponite RD to remove cadmium.

PubMed

Mola Ali Abasiyan, Sara; Mahdavinia, Gholam Reza

2018-05-01

In this study, magnetic nanocomposite hydrogels based on polyvinyl alcohol were synthesized. Magnetic polyvinyl alcohol/laponite RD (PVA-mLap) nanocomposites were characterized by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, and Fourier transform infrared spectroscopy. The results indicated that PVA-mLap had desirable magnetic-sorption properties and magnetic-laponite nanoparticles were successfully synthesized and added to polyvinyl alcohol. The present nanocomposites were applied to remove Cd 2+ from aqueous solution. The influence of initial Cd 2+ concentration, magnetic-laponite concentration, pH, and ionic strength on adsorption isotherm was investigated. Heterogeneity of adsorption sites was intensified by increasing magnetic concentration of adsorbents and by rising pH value. Results of ionic strength studies indicated that by increasing ionic strength more than four times, the adsorption of Cd 2+ has only decreased around 15%. According to the results, the dominant mechanism of Cd 2+ sorption by the present adsorbents was determined chemical and specific sorption. Therefore, the use of the present nanocomposites as a powerful adsorbent of Cd 2+ in the wastewater treatment is suggested. Isotherm data were described by using Freundlich and Langmuir models, and better fitting was introduced Langmuir model.

Biosorption of trivalent chromium by free and immobilized blue green algae: kinetics and equilibrium studies.

PubMed

Shashirekha, V; Sridharan, M R; Swamy, Mahadeswara

2008-03-01

The process of biosorption of trivalent chromium (Cr(3+)) by live culture of Spirulina platensis and the sorption potential by the dried biomass, in both free and immobilized states have been investigated for a simulated chrome liquor in the concentration range of 100-4500 ppm. Both live and dried biomass were very good biosorbents as they could remove high amounts of chromium from tannery wastewater. Polyurethane foam and sodium alginate were used as immobilizing agents and their performances compared. Biosorption kinetic data on Cr(3+) sorption onto dried biomass were analyzed using pseudo-first-and pseudo-second-order kinetic models in batch column experiments. The second-order equation was more appropriate to predict the rate of biosorption. Subsequently, the effects of height of packing & diameter of the column, concentration of blue-green algae (BGA) in varying amounts of sodium alginate, chromium concentration were studied. The results fit into both Langmuir & Freundlich isotherm models with very high regression coefficients. Furthermore, equilibrium studies using retan chrome liquor (RCL), with a chromium concentration of 1660 ppm, obtained from a tannery also showed promising results. In general, our studies indicate the efficacy of the algal species in removal of chromium from tannery wastewater.

Adsorption of leather dye onto activated carbon prepared from bottle gourd: equilibrium, kinetic and mechanism studies.

PubMed

Foletto, Edson Luiz; Weber, Caroline Trevisan; Paz, Diego Silva; Mazutti, Marcio Antonio; Meili, Lucas; Bassaco, Mariana Moro; Collazzo, Gabriela Carvalho

2013-01-01

Activated carbon prepared from bottle gourd has been used as adsorbent for removal of leather dye (Direct Black 38) from aqueous solution. The activated carbon obtained showed a mesoporous texture, with surface area of 556.16 m(2) g(-1), and a surface free of organic functional groups. The initial dye concentration, contact time and pH significantly influenced the adsorption capacity. In the acid region (pH 2.5) the adsorption of dye was more favorable. The adsorption equilibrium was attained after 60 min. Equilibrium data were analyzed by the Langmuir, Freundlich, Dubinin-Radushkevich and Temkin isotherm models. The equilibrium data were best described by the Langmuir isotherm, with maximum adsorption capacity of 94.9 mg g(-1). Adsorption kinetic data were fitted using the pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The adsorption kinetic was best described by the second-order kinetic equation. The adsorption process was controlled by both external mass transfer and intraparticle diffusion. Activated carbon prepared from bottle gourd was shown to be a promising material for adsorption of Direct Black 38 from aqueous solution.

Adsorption performance of creatinine on dialdehyde nanofibrillated cellulose derived from potato residues.

PubMed

Cui, Dongli; Liu, Zehua; Yang, Yaxing; Huang, Rijin; Cheng, Xiaojuan; Fatehi, Pedram; Sun, Bo

2016-01-01

Potato residue is vastly produced in the food industry but it is landfilled. This article describes the treatment of purified cellulose derived from potato residues by a high pressure homogenizer to produce nano-fibrillated cellulose (NFC), which was then oxidized by sodium periodate to prepare dialdehyde nano-fibrillated cellulose (DANFC). The produced NFC and DANFC were characterized by a scanning electron microscope (SEM) and Fourier transform infrared spectroscopy (FTIR). The orthogonal experiment was induced to obtain the maximum degree of oxidation (DO) on DANFC. The results indicated that the optimal conditions were 40°C and pH 3. Alternatively, the isotherm and kinetic studies for the adsorption of creatinine on DANFC with different DOs (70.5 and 88.8%) were investigated, and the experimental results fitted well into Freundlich isotherm model and pseudo second-order kinetic model. The maximum adsorption capacities of DANFCs with the DO of 70.55 and 88.85% were 6.7 and 17.2 mg g(-1) , respectively, which were achieved under the conditions of 37°C and initial creatinine concentration of 100 mg L(-1). © 2015 American Institute of Chemical Engineers.

The phosphorus fractions and adsorption-desorption characteristics in the Wuliangsuhai Lake, China.

PubMed

Wang, Xinglei; Wei, Jinxing; Bai, Na; Cha, Hancaicike; Cao, Can; Zheng, Kexuan; Liu, Ying

2018-05-11

The phosphorus (P) fractions and adsorption-desorption characteristics in the Wuliangsuhai Lake were investigated through molybdenum blue/ascorbic acid method and indoor simulation experiments, respectively. The results showed that the highest total phosphorus concentration in overlying water (W-TP) was found in S1 which was in the hypereutrophic type. The mean concentration of particulate organic phosphorus (POP) was the most abundant P fraction (31.35% of the W-TP). The results of TP contents in sediments (S-TP) indicated that the most sampling sites were in the mild level of pollution. The contents of calcium-bound P (HCl-P) and residual P (Res-P) fractions together comprised 83.03-98.10% of the S-TP. Pseudo-second-order models fitted well with the adsorption-desorption kinetic of P fractions. The Langmuir and Freundlich models well described the adsorption isotherm of P fractions. The results of adsorption-desorption of P fractions indicated that the adsorption capacity was strong, the chemical adsorption was dominant, and the sediments was a source of P. Accordingly, we concluded that the Wuliangsuhai Lake was in the moderate pollution level, and the sediments as a source could desorb P in natural aquatic environment.

Uranium removal from aqueous solution by coir pith: equilibrium and kinetic studies.

PubMed

Parab, Harshala; Joshi, Shreeram; Shenoy, Niyoti; Verma, Rakesh; Lali, Arvind; Sudersanan, M

2005-07-01

Basic aspects of uranium adsorption by coir pith have been investigated by batch equilibration. The influence of different experimental parameters such as final solution pH, adsorbent dosage, sorption time, temperature and various concentrations of uranium on uptake were evaluated. Maximum uranium adsorption was observed in the pH range 4.0-6.0. The Freundlich and Langmuir adsorption models were used for the mathematical description of the adsorption equilibrium. The equilibrium data fitted well to both the equilibrium models in the studied concentration range of uranium (200-800 mg/l) and temperatures (305-336 K). The coir pith exhibited the highest uptake capacity for uranium at 317 K, at the final solution pH value of 4.3 and at the initial uranium concentration of 800 mg/l. The kinetics of the adsorption process followed a second-order adsorption. The adsorbent used proved to be suitable for removal of uranium from aqueous solutions. 0.2 N HCl was effective in uranium desorption. The results indicated that the naturally abundant coir pith of otherwise nuisance value exhibited considerable potential for application in removal of uranium from aqueous solution.

Selective removal of organochlorine pesticides (OCPs) from aqueous solution by triolein-embedded composite adsorbent.

PubMed

Ru, J; Liu, H J; Qu, J H; Wang, A M; Dai, R H; Wang, Z J

2007-01-01

A novel composite adsorbent (CA-T) was used for the selective removal of organochlorine pesticides (OCPs) from aqueous solution. The adsorbent was composed of the supporting activated carbon and the surrounding triolein-embedded cellulose acetate membrane. Scanning electron microscopy (SEM), N2 adsorption isotherms and fluorescence methods were used to characterize the physicochemical properties of CA-T. Triolein was perfectly embedded in the cellulose acetate membrane and deposited on the surface of activated carbon. The adsorbent was stable in water and no triolein leakage was detected during the test periods. Some organochlorine pesticides (OCPs), such as dieldrin, endrin, aldrin, and heptachlor epoxide, were used as model contaminants and removed by CA-T in laboratory batch experiments. The adsorption isotherm followed the Freundlich equation and the kinetic data fitted well to the pseudo-second-order reaction model. Results also indicated that CA-T appeared to be a promising adsorbent with good selectivity and satisfactory removal rate for lipophilic OCPs from aqueous solutions when present in trace amounts. The adsorption rate and removal efficiency for lipophilic OCPs were positively related to their octanol-water partition coefficients (log K(ow)). Lower residual concentrations of OCPs were achieved when compared to granular activated carbon (GAC).

CR-100 synthetic zeolite adsorption characteristics toward Northern Banat groundwater ammonia.

PubMed

Tomić, Željko; Kukučka, Miroslav; Stojanović, Nikoleta Kukučka; Kukučka, Andrej; Jokić, Aleksandar

2016-10-14

The adsorption characteristics of synthetic zeolite CR-100 in a fixed-bed system using continuous flow of groundwater containing elevated ammonia concentration were examined. The possibilities for adsorbent mass calculation throughout mass transfer zone using novel mathematical approach as well as zeolite adsorption capacity at every sampling point in time or effluent volume were determined. The investigated adsorption process consisted of three clearly separated steps indicated to sorption kinetics. The first step was characterized by decrease and small changes in effluent ammonia concentration vs. experiment time and quantity of adsorbed ammonia per mass unit of zeolite. The consequences of this phenomenon were showed in the plots of the Freundlich and the Langmuir isotherm models through a better linear correlation according as graphical points contingent to the first step were not accounted. The Temkin and the Dubinin-Radushkevich isotherm models showed the opposite tendency with better fitting for overall measurements. According to the obtained isotherms parameter data, the investigated process was found to be multilayer physicochemical adsorption, and also that synthetic zeolite CR-100 is a promising material for removal of ammonia from Northern Banat groundwater with an ammonia removal efficiency of 90%.

The adsorption features between insecticidal crystal protein and nano-Mg(OH)2.

PubMed

Pan, Xiaohong; Xu, Zhangyan; Zheng, Yilin; Huang, Tengzhou; Li, Lan; Chen, Zhi; Rao, Wenhua; Chen, Saili; Hong, Xianxian; Guan, Xiong

2017-12-01

Nano-Mg(OH) 2 , with low biological toxicity, is an ideal nano-carrier for insecticidal protein to improve the bioactivity. In this work, the adsorption features of insecticidal protein by nano-Mg(OH) 2 have been studied. The adsorption capacity could reach as high as 136 mg g -1 , and the adsorption isotherm had been fitted with Langmuir and Freundlich models. Moreover, the adsorption kinetics followed a pseudo-first or -second order rate model, and the adsorption was spontaneous and an exothermic process. However, high temperatures are not suitable for adsorption, which implies that the temperature would be a critical factor during the adsorption process. In addition, FT-IR confirmed that the protein was adsorbed on the nano-Mg(OH) 2 , zeta potential analysis suggested that insecticidal protein was loaded onto the nano-Mg(OH) 2 not by electrostatic adsorption but maybe by intermolecular forces, and circular dichroism spectroscopy of Cry11Aa protein before and after loading with nano-Mg(OH) 2 was changed. The study applied the adsorption information between Cry11Aa and nano-Mg(OH) 2 , which would be useful in the practical application of nano-Mg(OH) 2 as a nano-carrier.

Potentiality of Neopestalotiopsis clavispora ASU1 in biosorption of cadmium and zinc.

PubMed

Hassan, Sedky H A; Koutb, Mostafa; Nafady, Nivien Allam; Hassan, Elhagag Ahmed

2018-07-01

In this study, a fungal isolate was isolated from avocado fruit collected from a market in Makkah city, Saudi Arabia, and identified as Neopestalotiopsis clavispora ASU1. The biomass of Neopestalotiopsis clavispora ASU1 was used as a natural bio-sorbent for removal of Cd(II) and Zn(II) from aqueous solutions. Characterization of fungal biomass was performed using Fourier transform infrared spectroscopy, X-ray Diffractometer, and BET surface area. Different factors on Cd(II) and Zn(II) biosorption were studied to evaluate the maximum conditions for metals biosorption. The (q max ) for Cd(II) and Zn (II) by N. clavispora ASU1 calculated from the Langmuir adsorption isotherm was 185.3 ± 0.25 and 153.8 ± 0.21 mg/g, respectively. Based on r 2 , the equilibrium biosorption isotherms fitted well with Langmuir model than Freundlich isotherm. The adsorption kinetics was studied, and the biosorption followed to the pseudo-second-order model. Thus, the current study indicated that the biomass of N. clavispora ASU1 is an effective adsorbent for the removal of heavy metals from aqueous solutions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Biosorption of hexavalent chromium from aqueous medium with Opuntia biomass.

PubMed

Fernández-López, José A; Angosto, José M; Avilés, María D

2014-01-01

The biosorption of hexavalent chromium from aqueous solutions by Opuntia cladodes and ectodermis from cactus fruits was investigated. Both types of biomass are considered low-cost, natural, and ecofriendly biosorbents. Batch experiments were carried out to determine Cr(VI) biosorption capacity and the efficiency of the biosorption process under different pH, initial Cr(VI) concentration, and sorbent dosage. The biosorption of Cr(VI) by Opuntia biomass was highly pH dependent, favoring higher metal uptake at low pH. The higher biosorption capacity was exhibited at pH 2. The optimal conditions were obtained at a sorbent dosage of 1 g L(-1) and initial metal concentration of 10 mg L(-1). Biosorption kinetic data were properly fitted with the pseudo-second-order kinetic model. The rate constant, the initial biosorption rate, and the equilibrium biosorption capacity were determined. The experimental equilibrium data obtained were analyzed using two-parameter isotherm models (Langmuir, Freundlich, and Temkin). The Langmuir maximum monolayer biosorption capacity (q max) was 18.5 mg g(-1) for cladodes and 16.4 mg g(-1) for ectodermis. The results suggest that Opuntia biomass could be considered a promising low-cost biosorbent for the ecofriendly removal of Cr(VI) from aqueous systems.

Poly(acrylic acid) modifying bentonite with in-situ polymerization for removing lead ions.

PubMed

He, Y F; Zhang, L; Yan, D Z; Liu, S L; Wang, H; Li, H R; Wang, R M

2012-01-01

In this paper, a new kind of poly(acrylic acid) modified clay adsorbent, the poly(acrylic acid)/bentonite composite (PAA/HB) was prepared by in-situ polymerization, and utilized to remove lead(II) ions from solutions. The maximum adsorption of adsorbent is at pH 5 for metal ions, whereas the adsorption starts at pH 2. The effects of contact time (5-60 min), initial concentration of metal ions (200-1,000 mg/L) and adsorbent dosage (0.04-0.12 g/100 mL) have been reported in this article. The experimental data were investigated by means of kinetic and equilibrium adsorption isotherms. The kinetic data were analyzed by the pseudo-first-order and pseudo-second-order equation. The experimental data fitted the pseudo-second-order kinetic model very well. Langmuir and Freundlich isotherms were tried for the system to better understand the adsorption isotherm process. The maximal adsorption capacity of the lead(II) ions on the PAA/HB, as calculated from the Langmuir model, was 769.2 mg/g. The results in this study indicated that PAA/HB was an attractive candidate for removing lead(II) (99%).

Preparation and evaluation of molecularly imprinted polymer for selective recognition and adsorption of gossypol.

PubMed

Zhi, Keke; Wang, Lulu; Zhang, Yagang; Zhang, Xuemin; Zhang, Letao; Liu, Li; Yao, Jun; Xiang, Wei

2018-03-01

Molecularly imprinted polymers (MIPs) were designed and prepared via bulk thermal polymerization with gossypol as the template molecule and dimethylaminoethyl methacrylate as the functional monomer. The morphology and microstructures of MIPs were characterized by scanning electron microscope and Brunauer-Emmett-Teller surface areas. Static adsorption tests were performed to evaluate adsorption behavior of gossypol by the MIPs. It was found that adsorption kinetics and adsorption isotherms data of MIPs for gossypol were fit well with the pseudo-second-order model and Freundlich model, respectively. Scatchard analysis showed that heterogeneous binding sites were formed in the MIPs, including lower-affinity binding sites with the maximum adsorption of 252 mg/g and higher-affinity binding sites with the maximum adsorption of 632 mg/g. Binding studies also revealed that MIPs had favorable selectivity towards gossypol compared with non-imprinted polymers. Furthermore, adsorption capacity of MIPs maintained above 90% after 5 regeneration cycles, indicating MIPs were recyclable and could be used multiple times. These results demonstrated that prepared MIPs could be a promising functional material for selective adsorption of gossypol. Copyright © 2017 John Wiley & Sons, Ltd.

Adsorbent material based on passion-fruit wastes to remove lead (Pb), chromium (Cr) and copper (Cu) from metal-contaminated waters

NASA Astrophysics Data System (ADS)

Campos-Flores, Gaby; Castillo-Herrera, Alberto; Gurreonero-Fernández, Julio; Obeso-Obando, Aída; Díaz-Silva, Valeria; Vejarano, Ricardo

2018-04-01

The aim of the present work was to evaluate the feasibility of passion-fruit shell (PFS) biomass as adsorbent material to remove heavy metals from contaminated waters. Model mediums were used, which were composed of distilled water and the respective metal: lead (Pb), chromium (Cr) and copper (Cu), with a dose of 10g of dry PFSbiomass per liter of medium. The residual concentration of each metal was determined by Atomic Absorption Spectrophotometry (AAS). A good adsorption capacity was exhibited by this agro industrial waste, achieving removal levels of 96,93 and 82% for Pb, Cr and Cu, respectively. In addition, the results obtained showed an adequate fit to the Freundlich model (R2 > 0.91), on the basis of which, the following values of adsorption capacity (k: 1.7057, 0.6784, 0.3302) and adsorption intensity (n: 0.6869, 2.3474, 1.0499), for Pb, Cr and Cu respectively, were obtained. Our results suggest that Pb, Cr and Cu ions can be removed by more than 80% by using this agro industrial waste, which with a minimum treatment could be used as an adsorbent material in the treatment of metal-contaminated waters.

Using natural Chinese zeolite to remove ammonium from rainfall runoff following urea fertilization of a paddy rice field.

PubMed

Wang, Xiao-Ling; Qiao, Bin; Li, Song-Min; Li, Jian-Sheng

2016-03-01

The potential of natural Chinese zeolite to remove ammonium from rainfall runoff following urea applications to a paddy rice field is assessed in this study. Laboratory batch kinetic and isotherm experiments were carried out first to investigate the ammonium adsorption capacity of the natural zeolite. Field experiments using zeolite adsorption barriers installed at drain outlets in a paddy rice field were also carried out during natural rainfall events to evaluate the barrier's dynamic removal capacity of ammonium. The results demonstrate that the adsorption kinetics are accurately described by the Elovich model, with a coefficient of determination (R (2)) ranging from 0.9705 to 0.9709, whereas the adsorption isotherm results indicate that the Langmuir-Freundlich model provides the best fit (R (2) = 0.992) for the equilibrium data. The field experiments show that both the flow rate and the barrier volume are important controls on ammonium removal from rainfall runoff. A low flow rate leads to a higher ammonium removal efficiency at the beginning of the tests, while a high flow rate leads to a higher quantity of ammonium adsorbed over the entire runoff process.

Thermodynamic and kinetic studies of biosorption of iron and manganese from aqueous medium using rice husk ash

NASA Astrophysics Data System (ADS)

Adekola, F. A.; Hodonou, D. S. S.; Adegoke, H. I.

2016-11-01

The adsorption behavior of rice husk ash with respect to manganese and iron has been studied by batch methods to consider its application for water and waste water treatment. The optimum conditions of adsorption were determined by investigating the effect of initial metal ion concentration, contact time, adsorbent dose, pH value of aqueous solution and temperature. Adsorption equilibrium time was observed at 120 min. The adsorption efficiencies were found to be pH dependent. The equilibrium adsorption experimental data were found to fit the Langmuir, Freundlich and Temkin isotherms for iron, but fitted only Langmuir isotherm for manganese. The pseudo-second order kinetic model was found to describe the manganese and iron kinetics more effectively. The thermodynamic experiment revealed that the adsorption processes involving both metals were exothermic. The adsorbent was finally applied to typical raw water with initial manganese and iron concentrations of 3.38 mg/l for Fe and 6.28 mg/l, respectively, and the removal efficiency was 100 % for Mn and 70 % for Fe. The metal ions were desorbed from the adsorbent using 0.01 M HCl, it was found to quantitatively remove 67 and 86 % of Mn and Fe, respectively, within 2 h. The results revealed that manganese and iron are considerably adsorbed on the adsorbent and could be an economic method for the removal of these metals from aqueous solutions.

[Effects of soil trituration size on adsorption of oxytetracycline on soils].

PubMed

Qi, Rui-Huan; Li, Zhao-Jun; Long, Jian; Fan, Fei-Fei; Liang, Yong-Chao

2011-02-01

In order to understand the effects of soil trituration size on adsorption of oxytetracycline (OTC) on soils, two contrasting soils including moisture soil and purplish soil were selected to investigate adsorption of OTC on these soils, at the scales of no more than 0.20 mm, 0.84 mm, 0.25 mm and 0.15 mm, using the method of batch equilibrium experiments respectively. The results presented as the following: (1) Adsorption amount of OTC on moisture soil and purplish soil increased with the sampling time, and reached to equilibration at 24 h. First-order kinetic model, second-order kinetic model, parabolic-diffusion kinetic model, Elovich kinetic model, and two-constant kinetic model could be used to fit the changes in adsorption on soils with sampling time. Adsorption of OTC on two soils consisted of two processes such as quick adsorption and slow adsorption. Quick adsorption process happened during the period of 0-0.5 h. The adsorption rates of OTC on soils were higher at the small trituration size than those at the large trituration size, and at the same trituration size, the k(f) of purplish soil was about two times higher than those of moisture soil. (2) Adsorption isotherms of OTC on two soils with different trituration sizes were deviated from the linear model. The data were fitted well to Freundlich and Langmuir models, with the correlation coefficients between 0.956 and 0.999. The values of k(f) and q(m) for purplish soil were higher than those for moisture soil. At the same soil, adsorption amount of OTC increased with the decreases of soil trituration size. The results suggested that it is important to select the appropriate trituration size, based on the physical and chemical properties such as soil particle composition and so on, when the fate of antibiotics on soils was investigated.

Removal of toxic zinc from water/wastewater using eucalyptus seeds activated carbon: non-linear regression analysis.

PubMed

Senthil Kumar, Ponnusamy; Saravanan, Anbalagan; Anish Kumar, Kodyingil; Yashwanth, Ramesh; Visvesh, Sridharan

2016-08-01

In the present study, a novel activated carbon was prepared from low-cost eucalyptus seeds, which was utilised for the effectively removal of toxic zinc from the water/wastewater. The prepared adsorbent was studied by Fourier transform infrared spectroscopy and scanning electron microscopic characterisation studies. Adsorption process was experimentally performed for optimising the influencing factors such as adsorbent dosage, solution pH, contact time, initial zinc concentration, and temperature for the maximum removal of zinc from aqueous solution. Adsorption isotherm of zinc removal was ensued Freundlich model, and the kinetic model ensued pseudo-second order model. Langmuir monolayer adsorption capacity of the adsorbent for zinc removal was evaluated as 80.37 mg/g. The results of the thermodynamic studies suggested that the adsorption process was exothermic, thermodynamically feasible and impulsive process. Finally, a batch adsorber was planned to remove zinc from known volume and known concentration of wastewater using best obeyed model such as Freundlich. The experimental details showed the newly prepared material can be effectively utilised as a cheap material for the adsorption of toxic metal ions from the contaminated water.

Effect of artificial root exudates on the sorption and desorption of PAHs in meadow brown soils

NASA Astrophysics Data System (ADS)

Wang, Hong

2017-10-01

The batch equilibrium experiment was conducted to investigate the effect of artificial root exudates on sorption and desorption of phenanthrene and pyrene. The result showed sorption isotherms were fitted well to the Freundlich equation with the treatment of artificial root exudates. Fructose had the most obvious effect on sorption. The artificial root exudates improved desorption of PAHs, while low molecular weight organic acids were better than serine and fructose. The capability of sorption and desorption was strengthened with the increase of organic acids concentration. And the DOM in the solution might be the most important factor of the adsorption of PAHs in solid phase.

Modification of zeolite 4A for use as an adsorbent for glyphosate and as an antibacterial agent for water.

PubMed

Zavareh, Siamak; Farrokhzad, Zahra; Darvishi, Farshad

2018-07-15

The aim of this work was to design a low cost adsorbent for efficient and selective removal of glyphosate from water at neutral pH conditions. For this purpose, zeolite 4A, a locally abundant and cheap mineral material, was ion-exchanged with Cu 2+ to produce Cu-zeolite 4A. The FTIR results revealed that the modification has no important effect on chemical structure of zeolite 4A. After modification, highly crystalline zeolite 4A was converted to amorphous Cu-zeolite 4A according to XRD studies. The SEM images showed spherical-like particles with porous surfaces for Cu-zeolite 4A compared to cubic particles with smooth surfaces for zeolite 4A. Adsorption equilibrium data were well fitted with non-linear forms of Langmuir, Freundlich and Temkin isotherms. The maximum adsorption capacity for Cu-zeolite 4A was calculated to be 112.7 mg g -1 based on the Langmuir model. The adsorption of glyphosate by the modified adsorbent had fast kinetics fitted both pseudo-first-order and pseudo-second-order models. A mechanism based on chemical adsorption was proposed for the removal process. The modified adsorbent had a good selectivity to glyphosate over natural waters common cations and anions. It also showed desired regeneration ability as an important feature for practical uses. The potential use of the developed material as antibacterial agent for water disinfection filters was also investigated by MIC method. Relatively strong antibacterial activity was observed for Cu-zeolite 4A against Gram-positive and Gram-negative model bacteria while zeolite 4A had no antibacterial properties. No release of Cu 2+ to aqueous solutions was detected as unique feature of the developed material. Copyright © 2018 Elsevier Inc. All rights reserved.

Self-assembled three-dimensional reduced graphene oxide-based hydrogel for highly efficient and facile removal of pharmaceutical compounds from aqueous solution.

PubMed

Umbreen, Nadia; Sohni, Saima; Ahmad, Imtiaz; Khattak, Nimat Ullah; Gul, Kashif

2018-05-14

Herein, self-assembled three-dimensional reduced graphene oxide (RGO)-based hydrogels were synthesized and characterized in detail. A thorough investigation on the uptake of three widely used pharmaceutical drugs, viz. Naproxen (NPX), Ibuprofen (IBP) and Diclofenac (DFC) was carried out from aqueous solutions. To ensure the sustainability of developed hydrogel assembly, practically important parameters such as desorption, recyclability and applicability to real samples were also evaluated. Using the developed 3D hydrogels as adsorptive platforms, excellent decontamination for the above mentioned persistent pharmaceutical drugs was achieved in acidic pH with a removal efficiency in the range of 70-80%. These hydrogels showed fast adsorption kinetics and experimental findings were fitted to different kinetic models, such as pseudo-first order, pseudo-second order, intra-particle and the Elovich models in an attempt to better understand the adsorption kinetics. Furthermore, equilibrium adsorption data was fitted to the Langmuir and Freundlich models, where relatively higher R 2 values obtained in case of former one suggested that monolayer adsorption played an important part in drug uptake. Thermodynamic aspects were also studied and negative ΔG 0 values obtained indicated the spontaneous nature of adsorption process. The study was also extended to check practical utility of as-prepared hydrogels by spiking real aqueous samples with drug solution, where high % recoveries obtained for NPX, IBP and DFC were of particular importance with regard to prospective application in wastewater treatment systems. We advocate RGO-based hydrogels as environmentally benign, readily recoverable/recyclable material with excellent adsorption capacity for application in wastewater purification. Copyright © 2018 Elsevier Inc. All rights reserved.

Fe3O4 and MnO2 assembled on honeycomb briquette cinders (HBC) for arsenic removal from aqueous solutions.

PubMed

Zhu, Jin; Baig, Shams Ali; Sheng, Tiantian; Lou, Zimo; Wang, Zhuoxing; Xu, Xinhua

2015-04-09

In this study, a novel composite adsorbent (HBC-Fe3O4-MnO2) was synthesized by combining honeycomb briquette cinders (HBC) with Fe3O4 and MnO2 through a co-precipitation process. The purpose was to make the best use of the oxidative property of MnO2 and the adsorptive ability of magnetic Fe3O4 for enhanced As(III) and As(V) removal from aqueous solutions. Experimental results showed that the adsorption capacity of As(III) was observed to be much higher than As(V). The maximum adsorption capacity (2.16 mg/g) was achieved for As(III) by using HBC-Fe3O4-MnO2 (3:2) as compared to HBC-Fe3O4-MnO2 (2:1) and HBC-Fe3O4-MnO2 (1:1). The experimental data of As(V) adsorption fitted well with the Langmuir isotherm model, whereas As(III) data was described perfectly by Freundlich model. The pseudo-second-order kinetic model was fitted well for the entire adsorption process of As(III) and As(V) suggesting that the adsorption is a rate-controlling step. Aqueous solution pH was found to greatly affect the adsorption behavior. Furthermore, co-ions including HCO3(-) and PO4(3-) exhibited greater influence on arsenic removal efficiency, whereas Cl(-), NO3(-), SO4(2-) were found to have negligible effects on arsenic removal. Five consecutive adsorption-regeneration cycles confirmed that the adsorbent could be reusable for successive arsenic treatment and can be used in real treatment applications. Copyright © 2015 Elsevier B.V. All rights reserved.

The interactions between three typical PPCPs and LDH

NASA Astrophysics Data System (ADS)

Li, Erwei; Liao, Libing; Lv, Guocheng; Li, Zhaohui; Yang, Chengxue; Lu, Yanan

2018-03-01

With a positively charged layered structure, layered double hydroxide has potential applications in remediation of anionic contaminants, which has been a hot topic for recent years. In this study, a Cl type Mg-Al hydrotalcite (Cl-LDH) was prepared by a co-precipitation method. The adsorption process of three pharmaceuticals and personal care products (PPCPs) (tetracycline (TC), diclofenac sodium (DF), chloramphenicol (CAP)) by Cl-LDH was investigated by X-ray diffraction (XRD), Zeta potential, dynamic light scattering (DLS), BET, FT-IR spectroscopy and molecular dynamics simulation. The results showed that the adsorption equilibrium of TC and DF could be reached in 120 min, and the maximum adsorption capacity of the Cl-LDH for TC and DF were 1.85 mmol/g and 0.95 mmol/g, respectively. The adsorption isothermal of TC was fitted with the Freundlich adsorption model, and the adsorption isothermal of DF was fitted with the Langmuir adsorption model. The adsorption dynamics of TC and DF followed the pseudo-second-order model. The adsorption mechanisms of the three PPCPs onto Cl-LDH were different based on the experimental results and molecular dynamics simulation. The TC adsorption on Cl-LDH was mainly driven by the electrostatic interactions between the negative charge of TC and the positive charge of Cl-LDH. The uptake of anionic DF was attributed both to ion exchange of DF for Cl- and the electrostatic interaction between the negatively charged DF and the positively charged structure layer of Cl-LDH. Cl-LDH does not adsorb the neutral CAP due to no electrostatic interaction. The molecular dynamic simulation further confirmed different configurations of the three selected PPCPs in the interlayer of Cl-LDH, which were responsible for the different uptake process of PPCPs on Cl-LDH.

Sorption, degradation and transport phenomena of alcohol ethoxysulfates in agricultural soils. Laboratory studies.

PubMed

Fernández-Ramos, C; Rodríguez-Gómez, R; Reis, M S; Zafra-Gómez, A; Verge, C; de Ferrer, J A; Pérez-Pascual, M; Vílchez, J L

2017-03-01

In the present work, laboratory studies were conducted in order to determine and model the sorption, degradation and transport processes of alcohol ethoxysulfates (AES), one of the most important groups of anionic surfactants. Adsorption/desorption isotherms were obtained for several structurally related AES ethoxymers (homologue AES-C 12 E n with n = 0-10 ethoxymer units and homologue AES-C 14 E n with n = 0-7 ethoxymer units) using a batch equilibrium method. Data were fitted to a linear and a Freundlich isotherm models. Additionally, experiments in continuous-flow soil columns were also carried out and the breakthrough curves observed for each compound were studied. Breakthrough curves were used to determine the fundamental parameters of the transport model (hydrodynamic dispersion coefficient, degradation rate constant and adsorption/desorption isotherm slope), that is the main phenomena that take place simultaneously when AES move through agricultural soil. When the results obtained for the AES ethoxymers are combined, they reveal a clear and consistent trend towards a sorption increase with the number of ethoxylated units and with the length of the alkyl chain that opens the possibility to estimate the values of the transport parameters for other structurally related ethoxymers. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of magnetic ionomer for development of very fast and highly efficient uptake of triazo dye Direct Blue 71 form different water samples.

PubMed

Khani, Rouhollah; Sobhani, Sara; Beyki, Mostafa Hossein; Miri, Simin

2018-04-15

This research focuses on removing Direct Blue 71 (DB 71) from aqueous solution in an efficient and very fast route by ionic liquid mediated γ-Fe 2 O 3 magnetic ionomer. 2-hydroxyethylammonium sulphonate immobilized on γ-Fe 2 O 3 nanoparticles (γ-Fe 2 O 3 -2-HEAS) was used for this purpose. The influence of shaking time, medium pH, the concentration of sorbent and NaNO 3 on removal was evaluated to greatly influence removal extent. The optimal removal conditions were determined by response surface methodology based on the four-variable central composite design to obtain maximum removal efficiency and determine the significance and interaction effect of the variables on the removal of target triazo dye. The results have shown that an amount of 98.2% as % removal under the optimum conditions. The adsorption kinetics and isotherms were well fitted to a pseudo-second order model and Freundlich model, respectively. Based on these models, the maximum dye adsorption capacity (Q m ) of 47.60mgg -1 was obtained. Finally, the proposed nano-adsorbent was applied satisfactorily for removal of target triazo dye from different water samples. Copyright © 2017 Elsevier Inc. All rights reserved.

Sorption-desorption of antimony species onto calcined hydrotalcite: Surface structure and control of competitive anions.

PubMed

Constantino, Leonel Vinicius; Quirino, Juliana Nunes; Abrão, Taufik; Parreira, Paulo Sérgio; Urbano, Alexandre; Santos, Maria Josefa

2018-02-15

Calcined hydrotalcite can be applied to remove anionic contaminants from aqueous systems such as antimony species due to its great anion exchange capacity and high surface area. Hence, this study evaluated antimonite and antimonate sorption-desorption processes onto calcined hydrotalcite in the presence of nitrate, sulfate and phosphate. Sorption and desorption experiments of antimonite and antimonate were carried out in batch equilibrium and the post-sorption solids were analyzed by X-ray fluorescence (EDXRF). Sorption data were better fitted by dual-mode Langmuir-Freundlich model (R 2 >0.99) and desorption data by Langmuir model. High maximum sorption capacities were found for the calcined hydrotalcite, ranging from 617 to 790meqkg -1 . The competing anions strongly affected the antimony sorption. EDXRF analysis and mathematical modelling showed that sulfate and phosphate presented higher effect on antimonite and antimonate sorption, respectively. High values for sorption efficiency (SE=99%) and sorption capacity were attributed to the sorbent small particles and the large surface area. Positive hysteresis indexes and low mobilization factors (MF>3%) suggest very low desorption capacity to antimony species from LDH. These calcined hydrotalcite characteristics are desirable for sorption of antimony species from aqueous solutions. Copyright © 2017. Published by Elsevier B.V.

Removal of dieldrin from aqueous solution by a novel triolein-embedded composite adsorbent.

PubMed

Ru, Jia; Liu, Huijuan; Qu, Jiuhui; Wang, Aimin; Dai, Ruihua

2007-03-06

In this study, a novel triolein-embedded activated carbon composite adsorbent (CA-T) was prepared and applied for the adsorption and removal of dieldrin from aqueous systems. Experiments were carried out to investigate the adsorption behavior of dieldrin on CA-T, including adsorption isotherms, adsorption kinetics, the influence of initial concentration, temperature, shaking speed, pH and the addition of humic acid (HA) on adsorption. The adsorption isotherms accorded with Freundlich equation. Three kinetics models, including pseudo-first-order, pseudo-second-order and intraparticle diffusion models, were used to fit the experimental data. By comparing the correlation coefficients, it was found that both pseudo-second-order and intraparticle diffusion models were used to well describe the adsorption of dieldrin on CA-T. The addition of HA had little effect on dieldrin adsorption by CA-T. Results indicated that CA-T appeared to be a promising adsorbent for removing lipophilic dieldrin in trace amount, which was advantageous over pure granular activated carbon (GAC). The adsorption rate increased with increasing shaking speed, initial concentration and temperature, and remained almost unchanged in the pH range of 4-8. Thermodynamic calculations indicated that the adsorption reaction was spontaneous with a high affinity and the adsorption was an endothermic reaction.

Phenanthrene sorption with heterogeneous organic matter in a landfill aquifer material

USGS Publications Warehouse

Karapanagioti, H.K.; Sabatini, D.A.; Kleineidam, S.; Grathwohl, P.; Ligouis, B.

1999-01-01

Phenanthrene was used as a model chemical to study the sorption properties of Canadian River Alluvium aquifer material. Both equilibrium and kinetic sorption processes were evaluated through batch studies. The bulk sample was divided into subsamples with varying properties such as particle size, organic content, equilibration time, etc. in order to determine the effect of these properties on resulting sorption parameters. The data have been interpreted and the effect of experimental variables was quantified using the Freundlich isotherm model and a numerical solution of Fick's 2nd law in porous media. Microscopic organic matter characterization proved to be a valuable tool for explaining the results. Different organic matter properties and sorption mechanisms were observed for each soil subsample. Samples containing coal particles presented high Koc values. Samples with organic matter dominated by organic coatings on quartz grains presented low Koc values and contained a high percentage of fast sorption sites. The numerical solution of Fick's 2ndlaw requires the addition of two terms (fast and slow) in order to fit the kinetics of these heterogeneous samples properly. These results thus demonstrate the need for soil organic matter characterization in order to predict and explain the sorption properties of a soil sample containing heterogeneous organic matter and also the difficulty and complexity of modeling sorption in such samples.

Characterization of tannery sludge activated carbon and its utilization in the removal of azo reactive dye.

PubMed

Geethakarthi, A; Phanikumar, B R

2012-03-01

The removal of azo Reactive Red 31(RR31) from synthetic dye solution using tannery sludge-developed activated carbon (TSC) was investigated. TSC was prepared from a combination of physical and chemical activation. The developed TSC was characterized by FT-IR, SEM, TG-DTA, specific surface area and zero point charge of pH (pH(zpc)). The isotherm models, kinetic models and thermodynamic parameters were also analysed to describe the adsorptive behaviour of TSC. The effect of contact time, initial dye concentration, carbon dosage, agitation speed, initial pH and temperature were carried out for batch adsorption studies. The isotherm plot of the dye RR31 on TSC fitted better with the Langmuir adsorption isotherm than the Freundlich model. The maximum monolayer adsorption capacity of TSC in the removal of RR31 ranged from 23.15 to 39.37 mg/g. The thermodynamic parameters showed the endothermic and physical nature of the Reactive Red 31 adsorption on TSC. The entropy and enthalpy values were 181.515 J/Kmol and 5.285 kJ/mol, respectively. The developed cationic tannery sludge carbon was found to be an effective adsorbent in the removal of the anionic azo reactive dye RR31.

Synergistically strengthened 3D micro-scavenger cage adsorbent for selective removal of radioactive cesium

PubMed Central

Jang, Sung-Chan; Kang, Sung-Min; Haldorai, Yuvaraj; Giribabu, Krishnan; Lee, Go-Woon; Lee, Young-Chul; Hyun, Moon Seop; Han, Young-Kyu; Roh, Changhyun; Huh, Yun Suk

2016-01-01

A novel microporous three-dimensional pomegranate-like micro-scavenger cage (P-MSC) composite has been synthesized by immobilization of iron phyllosilicates clay onto a Prussian blue (PB)/alginate matrix and tested for the removal of radioactive cesium from aqueous solution. Experimental results show that the adsorption capacity increases with increasing the inactive cesium concentration from 1 ppm to 30 ppm, which may be attributed to greater number of adsorption sites and further increase in the inactive cesium concentration has no effect. The P-MSC composite exhibit maximum adsorption capacity of 108.06 mg of inactive cesium per gram of adsorbent. The adsorption isotherm is better fitted to the Freundlich model than the Langmuir model. In addition, kinetics studies show that the adsorption process is consistent with a pseudo second-order model. Furthermore, at equilibrium, the composite has an outstanding adsorption capacity of 99.24% for the radioactive cesium from aqueous solution. This may be ascribed to the fact that the AIP clay played a substantial role in protecting PB release from the P-MSC composite by cross-linking with alginate to improve the mechanical stability. Excellent adsorption capacity, easy separation, and good selectivity make the adsorbent suitable for the removal of radioactive cesium from seawater around nuclear plants and/or after nuclear accidents. PMID:27917913

Synergistically strengthened 3D micro-scavenger cage adsorbent for selective removal of radioactive cesium.

PubMed

Jang, Sung-Chan; Kang, Sung-Min; Haldorai, Yuvaraj; Giribabu, Krishnan; Lee, Go-Woon; Lee, Young-Chul; Hyun, Moon Seop; Han, Young-Kyu; Roh, Changhyun; Huh, Yun Suk

2016-12-05

A novel microporous three-dimensional pomegranate-like micro-scavenger cage (P-MSC) composite has been synthesized by immobilization of iron phyllosilicates clay onto a Prussian blue (PB)/alginate matrix and tested for the removal of radioactive cesium from aqueous solution. Experimental results show that the adsorption capacity increases with increasing the inactive cesium concentration from 1 ppm to 30 ppm, which may be attributed to greater number of adsorption sites and further increase in the inactive cesium concentration has no effect. The P-MSC composite exhibit maximum adsorption capacity of 108.06 mg of inactive cesium per gram of adsorbent. The adsorption isotherm is better fitted to the Freundlich model than the Langmuir model. In addition, kinetics studies show that the adsorption process is consistent with a pseudo second-order model. Furthermore, at equilibrium, the composite has an outstanding adsorption capacity of 99.24% for the radioactive cesium from aqueous solution. This may be ascribed to the fact that the AIP clay played a substantial role in protecting PB release from the P-MSC composite by cross-linking with alginate to improve the mechanical stability. Excellent adsorption capacity, easy separation, and good selectivity make the adsorbent suitable for the removal of radioactive cesium from seawater around nuclear plants and/or after nuclear accidents.

Synergistically strengthened 3D micro-scavenger cage adsorbent for selective removal of radioactive cesium

NASA Astrophysics Data System (ADS)

Jang, Sung-Chan; Kang, Sung-Min; Haldorai, Yuvaraj; Giribabu, Krishnan; Lee, Go-Woon; Lee, Young-Chul; Hyun, Moon Seop; Han, Young-Kyu; Roh, Changhyun; Huh, Yun Suk

2016-12-01

A novel microporous three-dimensional pomegranate-like micro-scavenger cage (P-MSC) composite has been synthesized by immobilization of iron phyllosilicates clay onto a Prussian blue (PB)/alginate matrix and tested for the removal of radioactive cesium from aqueous solution. Experimental results show that the adsorption capacity increases with increasing the inactive cesium concentration from 1 ppm to 30 ppm, which may be attributed to greater number of adsorption sites and further increase in the inactive cesium concentration has no effect. The P-MSC composite exhibit maximum adsorption capacity of 108.06 mg of inactive cesium per gram of adsorbent. The adsorption isotherm is better fitted to the Freundlich model than the Langmuir model. In addition, kinetics studies show that the adsorption process is consistent with a pseudo second-order model. Furthermore, at equilibrium, the composite has an outstanding adsorption capacity of 99.24% for the radioactive cesium from aqueous solution. This may be ascribed to the fact that the AIP clay played a substantial role in protecting PB release from the P-MSC composite by cross-linking with alginate to improve the mechanical stability. Excellent adsorption capacity, easy separation, and good selectivity make the adsorbent suitable for the removal of radioactive cesium from seawater around nuclear plants and/or after nuclear accidents.

Adsorptive removal of Cu(II) from aqueous solution and industrial effluent using natural/agricultural wastes.

PubMed

Singha, Biswajit; Das, Sudip Kumar

2013-07-01

The potentiality of low cost natural/agricultural waste biomasses for the removal of Cu(II) ion from aqueous solution has been investigated in batch experiments. The effect of various physico-chemical parameters such as initial pH, initial Cu(II) concentration, adsorbent dosage, contact time and temperature has been studied. The optimum pH for adsorption was found to be 6 for all adsorbents used. Kinetics data were best described by the pseudo-2nd-order model. The experimental data were fitted well with Freundlich and Halsey isotherm models. The diffusion coefficient and sorption energy indicated that the adsorption process was chemical in nature. Thermodynamic parameters such as ΔG°, ΔH° and ΔS° were calculated, and it was observed that the adsorption process was spontaneous and endothermic. The mean sorption energy was calculated using Dubinin-Radushkevich isotherm model and it confirmed that the sorption process was chemical in nature. Different active functional groups were identified by FTIR studies which were responsible for Cu(II) ion adsorption process. Application study using electroplating industrial waste water and regeneration experiment of the adsorbent were also investigated. Design procedure for the batch process was also reported. Copyright © 2013 Elsevier B.V. All rights reserved.

Preferable adsorption of phosphate using lanthanum-incorporated porous zeolite: Characteristics and mechanism

NASA Astrophysics Data System (ADS)

He, Yinhai; Lin, Hai; Dong, Yingbo; Wang, Liang

2017-12-01

The adsorbent, where lanthanum oxide was incorporated onto porous zeolite (La-Z), of preferable adsorption towards phosphate was prepared by hydrothermal synthesis. Based on pH effect results, La-Z would effectively sequestrate phosphate over wider pH range of 3.0-7.0, alkaline conditions were unfavorable for phosphate. The adsorption of phosphate was not significantly influenced by ionic strength and by coexisting anions of chloride, nitrate and sulfate but bicarbonate showed slightly greater negative effects, indicating La-Z possessed highly selectivity to phosphate. Adsorption of phosphate could be well fitted by pseudo-second-order model and the process was mainly controlled by intra-particle diffusion. Equilibrium adsorption demonstrated that Langmuir model was more suitable than Freundlich model for description phosphate adsorption and the adsorption capacity was 17.2 mg P g-1, which exhibited 95% utilization of incorporated La. Over 95% phosphate was eliminated in real effluent treatment when the dose was 2 g L-1. The underlying mechanism for phosphate capture was probed with Zeta potential and X-ray photoelectron spectroscope analysis, and the formation of La-P inner-sphere complexation was testified to be the dominant pathway. All the results suggested that the porous zeolite-supported lanthanum oxide can serve as a promising adsorbent for phosphate removal in realistic application.

Equilibrium, kinetic and thermodynamic studies of uranium biosorption by calcium alginate beads.

PubMed

Bai, Jing; Fan, Fangli; Wu, Xiaolei; Tian, Wei; Zhao, Liang; Yin, Xiaojie; Fan, Fuyou; Li, Zhan; Tian, Longlong; Wang, Yang; Qin, Zhi; Guo, Junsheng

2013-12-01

Calcium alginate beads are potential biosorbent for radionuclides removal as they contain carboxyl groups. However, until now limited information is available concerning the uptake behavior of uranium by this polymer gel, especially when sorption equilibrium, kinetics and thermodynamics are concerned. In present work, batch experiments were carried out to study the equilibrium, kinetics and thermodynamics of uranium sorption by calcium alginate beads. The effects of initial solution pH, sorbent amount, initial uranium concentration and temperature on uranium sorption were also investigated. The determined optimal conditions were: initial solution pH of 3.0, added sorbent amount of 40 mg, and uranium sorption capacity increased with increasing initial uranium concentration and temperature. Equilibrium data obtained under different temperatures were fitted better with Langmuir model than Freundlich model, uranium sorption was dominated by a monolayer way. The kinetic data can be well depicted by the pseudo-second-order kinetic model. The activation energy derived from Arrhenius equation was 30.0 kJ/mol and the sorption process had a chemical nature. Thermodynamic constants such as ΔH(0), ΔS(0) and ΔG(0) were also evaluated, results of thermodynamic study showed that the sorption process was endothermic and spontaneous. Copyright © 2013 Elsevier Ltd. All rights reserved.

Rapeseed and Raspberry Seed Cakes as Inexpensive Raw Materials in the Production of Activated Carbon by Physical Activation: Effect of Activation Conditions on Textural and Phenol Adsorption Characteristics

PubMed Central

Smets, Koen; De Jong, Mats; Lupul, Iwona; Gryglewicz, Grazyna; Schreurs, Sonja; Carleer, Robert; Yperman, Jan

2016-01-01

The production of activated carbons (ACs) from rapeseed cake and raspberry seed cake using slow pyrolysis followed by physical activation of the obtained solid residues is the topic of this study. The effect of activation temperature (850, 900 and 950 °C), activation time (30, 60, 90 and 120 min) and agent (steam and CO2) on the textural characteristics of the ACs is investigated by N2 adsorption. In general, higher activation temperatures and longer activation times increase the BET specific surface area and the porosity of the ACs, regardless of the activation agent or raw material. Steam is more reactive than CO2 in terms of pore development, especially in the case of raspberry seed cake. The performance of the ACs in liquid adsorption is evaluated by batch phenol adsorption tests. Experimental data are best fitted by the Freundlich isotherm model. Based on total yield, textural characteristics and phenol adsorption, steam activation at 900 °C for 90 min and CO2 activation at 900 °C for 120 min are found as the best activation conditions. Raspberry seed cake turns out to be a better raw material than rapeseed cake. Moreover, AC from raspberry seed cake produced by steam activation at 900 °C for 90 min performs as well as commercial AC (Norit GAC 1240) in phenol adsorption. The adsorption kinetics of the selected ACs are best fitted by the pseudo-second-order model. PMID:28773684

Investigating the Heavy Metal Adsorption of Mesoporous Silica Materials Prepared by Microwave Synthesis

NASA Astrophysics Data System (ADS)

Zhu, Wenjie; Wang, Jingxuan; Wu, Di; Li, Xitong; Luo, Yongming; Han, Caiyun; Ma, Wenhui; He, Sufang

2017-05-01

Mesoporous silica materials (MSMs) of the MCM-41 type were rapidly synthesized by microwave heating using silica fume as silica source and evaluated as adsorbents for the removal of Cu2+, Pb2+, and Cd2+ from aqueous solutions. The effects of microwave heating times on the pore structure of the resulting MSMs were investigated as well as the effects of different acids which were employed to adjust the solution pH during the synthesis. The obtained MCM-41 samples were characterized by nitrogen adsorption-desorption analyses, X-ray powder diffraction, and transmission electron microscopy. The results indicated that microwave heating method can significantly reduce the synthesis time of MCM-41 to 40 min. The MCM-41 prepared using citric acid (c-MCM-41(40)) possessed more ordered hexagonal mesostructure, higher pore volume, and pore diameter. We also explored the ability of c-MCM-41(40) for removing heavy metal ions (Cu2+, Pb2+, and Cd2+) from aqueous solution and evaluated the influence of pH on its adsorption capacity. In addition, the adsorption isotherms were fitted by Langmuir and Freundlich models, and the adsorption kinetics were assessed using pseudo-first-order and pseudo-second-order models. The intraparticle diffusion model was studied to understand the adsorption process and mechanism. The results confirmed that the as-synthesized adsorbent could efficiently remove the heavy metal ions from aqueous solution at pH range of 5-7. The adsorption isotherms obeyed the Langmuir model, and the maximum adsorption capacities of the adsorbent for Cu2+, Pb2+, and Cd2+ were 36.3, 58.5, and 32.3 mg/g, respectively. The kinetic data were well fitted to the pseudo-second-order model, and the results of intraparticle diffusion model showed complex chemical reaction might be involved during adsorption process.

Lead (Pb2+) and copper (Cu2+) remediation from water using superparamagnetic maghemite (γ-Fe2O3) nanoparticles synthesized by Flame Spray Pyrolysis (FSP).

PubMed

Rajput, Shalini; Singh, Lok P; Pittman, Charles U; Mohan, Dinesh

2017-04-15

Superparamagnetic maghemite (γ-Fe 2 O 3 ) nanoparticles of controllable morphology were successfully synthesized using a flame spray pyrolysis (FSP) technique. Their physico-chemical properties, size, morphology, and surface chemistries were determined using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), selected area electron diffraction patterns (SAED), SEM-EDX, scanning electron microscopy (SEM), and pH ZPC (6.3). Elemental contents before and after adsorption were identified using energy dispersive X-ray fluorescence (ED-XRF), energy dispersive X-ray analysis (EDX) and elemental mapping. Surface area (S BET 79.35m 2 /g) and size distribution analyses were conducted using a surface area analyzer and dynamic light scattering (DLS), respectively. The magnetic moment (44.5 at 300K and 50.16 at 2K) was determined using a physical properties measurement system (PPMS). The first adsorption study using γ-Fe 2 O 3 nanoparticles synthesized by FSP to successfully remediate Pb 2+ and Cu 2+ from water is reported. Batch adsorption studies were carried out. An optimum pH of 5.0 was studied for Pb 2+ and Cu 2+ removal. Pb 2+ and Cu 2+ removal mechanisms by these maghemite nanoparticles were presented. The adsorption of Pb 2+ and Cu 2+ was highly pH-dependent. The metal ion uptake was mainly governed by electrostatic attractions. Sorption kinetic data followed the pseudo-second-order model. The Freundlich, Langmuir, Redlich-Peterson, Radke and Sips adsorption isotherm models were applied to interpret equilibrium data. The Freundlich and Langmuir isotherm equations best fit the respective equilibrium data for Pb 2+ and Cu 2+ . The maximum Langmuir adsorption capacities of these maghemite nanoparticles were 68.9mg/g at 45°C for Pb 2+ and 34.0mg/g at 25 °C for Cu 2+ . Thus, these maghemite nanoparticles made by FSP were readily prepared, characterized and showed promise for remediating heavy metal ions from aqueous solutions. Copyright © 2016 Elsevier Inc. All rights reserved.

Novel biosynthesized silver nanoparticles from cobweb as adsorbent for Rhodamine B: equilibrium isotherm, kinetic and thermodynamic studies

NASA Astrophysics Data System (ADS)

Azeez, Luqmon; Lateef, Agbaje; Adebisi, Segun A.; Oyedeji, Abdulrasaq O.

2018-03-01

This study has investigated the adsorption of Rhodamine B (Rh-B) dye on novel biosynthesized silver nanoparticles (AgNPs) from cobweb. The effects of contact time, initial pH, initial dye concentration, adsorbent dosage and temperature were studied on the removal of Rh-B and they significantly affected its uptake. Adsorption isotherms were evaluated using Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherm models. The adsorption process was best described by Langmuir isotherm with R 2 of 0.9901, indicating monolayer adsorption. The maximum adsorption capacity ( q max) of 59.85 mg/g showed that it has relatively high performance, while adsorption intensity showed a favourable adsorption process. Pseudo-second-order kinetics fitted best the rate of adsorption and intra-particle diffusion revealed both surface adsorption and intra-particle diffusion-controlled adsorption process. Negative values of thermodynamic parameters (Δ H°, Δ S° and Δ G°) indicated an exothermic and spontaneous adsorption process. The mean sorption energy ( E) and activation energy ( E a) suggested the uptake of Rh-B onto AgNPs was chemical in nature (chemosorption).

Molecular Imprinted Polymer of Methacrylic Acid Functionalised β-Cyclodextrin for Selective Removal of 2,4-Dichlorophenol

PubMed Central

Surikumaran, Hemavathy; Mohamad, Sharifah; Sarih, Norazilawati Muhamad

2014-01-01

This work describes methacrylic acid functionalized β-cyclodextrin (MAA-βCD) as a novel functional monomer in the preparation of molecular imprinted polymer (MIP MAA-βCD) for the selective removal of 2,4-dichlorophenol (2,4-DCP). The polymer was characterized using Fourier Transform Infrared (FTIR) spectroscopy, Brunauer-Emmett-Teller (BET) and Field Emission Scanning Electron Microscopy (FESEM) techniques. The influence of parameters such as solution pH, contact time, temperature and initial concentrations towards removal of 2,4-DCP using MIP MAA-βCD have been evaluated. The imprinted material shows fast kinetics and the optimum pH for removal of 2,4-DCP is pH 7. Compared with the corresponding non-imprinted polymer (NIP MAA-βCD), the MIP MAA-βCD exhibited higher adsorption capacity and outstanding selectivity towards 2,4-DCP. Freundlich isotherm best fitted the adsorption equilibrium data of MIP MAA-βCD and the kinetics followed a pseudo-second-order model. The calculated thermodynamic parameters showed that adsorption of 2,4-DCP was spontaneous and exothermic under the examined conditions. PMID:24727378

Curcumin-containing chitosan nanoparticles as a potential mucoadhesive delivery system to the colon.

PubMed

Chuah, Lay Hong; Billa, Nashiru; Roberts, Clive J; Burley, Jonathan C; Manickam, Sivakumar

2013-01-01

In the present study, we investigate the mucoadhesive characteristics and release of the anticancer agent curcumin, contained in chitosan nanoparticles (CS-NPs). Such a system has potential therapeutic benefits in the treatment of colon cancer through prolonged retention and delivery. The CS-NPs were ionically gelled with tripolyphosphate (TPP) and registered an isoelectric pH of 6.2 (z-average diameter of 214 nm ± 1.0 nm). pH variations around the isoelectric point caused a reduction in CS-NPs electrical charge which correspondingly increased the z-average due to agglomeration. Curcumin release from CS-NPs was slowest at chitosan to TPP weight ratio of 3:1, with a significant retention (36%) at the end of 6 h. Adsorption isotherms of mucin on CS-NPs fitted both the Freundlich and Langmuir models, suggesting a monolayer-limited adsorption on heterogeneous sites with varied affinities. Encapsulated curcumin exerted an influence on the adsorption of mucin due to H-bonding as well as π-π interactions between the phenolic moieties of curcumin and mucin.

Adsorption mechanism of magnetically separable Fe3O4/graphene oxide hybrids

NASA Astrophysics Data System (ADS)

Ouyang, Ke; Zhu, Chuanhe; Zhao, Ya; Wang, Leichao; Xie, Shan; Wang, Qun

2015-11-01

A reclaimable Fe3O4/graphene oxide (GO) magnetic hybrid was successfully synthesized via a facile one-pot polyol approach and employed as a recyclable adsorbent for Bisphenol A (BPA) in aqueous solutions. The maximum adsorption capacity (qm) of the Fe3O4/GO hybrid for BPA was 72.80 mg/g at 273 K. The kinetics of the adsorption process and the adsorption isotherm data were fitted using the Freundlich equation and a pseudo-second-order kinetic model. The results of the thermodynamic parameters ΔH°, ΔS° and ΔG° showed that the adsorption process was exothermic and spontaneous. Furthermore, the reusability of the samples was investigated, and the results indicated that the samples exhibited high stability. The magnetic characterization demonstrated that hybrids were superparamagnetic and could be recovered conveniently by magnetic separation. The strong π-π interaction was determined to be the predominant driving force behind the adsorption of BPA onto the Fe3O4/GO hybrid. Therefore, the Fe3O4/GO hybrid could be regarded as a potential adsorbent for wastewater treatment and purification processes.

Adsorption behavior and mechanism of acidic blue 25 dye onto cucurbit[8]uril: A spectral and DFT study

NASA Astrophysics Data System (ADS)

Luo, Hanhan; Huang, Xiangyu; Luo, Yuhan; Li, Zhuang; Li, Lan; Gao, Chao; Xiong, Jinyan; Li, Wei

2018-03-01

The acidic blue 25 (AB25) dye was efficiently adsorbed by CB [8]; the saturated adsorption capacity (qexp) reached 434.8 mg/g and was far higher than those of previous reported adsorbents. The Langmuir and Freundich isotherms were used to fit the equilibrium data, and the results showed that the Freundlich isotherm seemed to agree better with the AB25 adsorption. The adsorption kinetics followed the pseudo-second-order model. Calculated thermodynamic parameters showed that the adsorption of AB25 onto CB [8] was a spontaneous and enthalpy-driven process. The adsorption mechanism was explored by N2 adsorption-desorption, TG, FT-IR, UV-vis as well as MD simulation and DFT calculations. TG analysis revealed that a new inclusion complex was produced, and FT-IR,UV-vis spectrum and DFT calculations verify its structure. In this inclusion complex, the AB25 dye molecule inserted into cavities of CB [8] from portal, and the sulfonate and phenyl groups stayed in the hydrophobic cavity. TDDFT calculations indicated that all excitation arisen from π → π* transition.

Natural biosorbents (garlic stem and horse chesnut shell) for removal of chromium(VI) from aqueous solutions.

PubMed

Parlayıcı, Şerife; Pehlivan, Erol

2015-12-01

The biosorption of Cr(VI) by the garlic stem (GS)-Allium sativum L. and horse chesnut shell (HCS)-Aesculus hippocastanum plant residues in a batch type reactor was studied in detail for the purpose of wastewater treatment. The influence of initial Cr(VI) concentration, time, and pH was investigated to optimize Cr(VI) removal from aqueous solutions and equilibrium isotherms and kinetic data. This influence was evaluated. The adsorption capacity of the GS and the HCS for Cr(VI) was determined with the Langmuir and Freundlich isotherm models, and the data was fitted to the Langmuir. The adsorption capacity of the GS and the HCS was found to be 103.09 and 142.85 mg/g of adsorbent from a solution containing 3000 ppm of Cr(VI), respectively. The GS's capacity was considerably lower than that of the HCS in its natural form. Gibbs free energy was spontaneous for all interactions, and the adsorption process exhibited exothermic enthalpy values. The HCS was shown to be a promising biosorbent for Cr(VI) removal from aqueous solutions.

Highly selective defluoridation of brick tea infusion by tea waste supported aluminum oxides.

PubMed

Peng, Chuanyi; Xi, Junjun; Chen, Guijie; Feng, Zhihui; Ke, Fei; Ning, Jingming; Li, Daxiang; Ho, Chi-Tang; Cai, Huimei; Wan, Xiaochun

2017-03-01

Brick tea usually contains very high fluoride, which may affect human health. Biosorbents have received much attention for selective removal of fluoride because of low cost, environmental friendliness, and relative safeness. In the present study, a highly selective fluoride tea waste based biosorbent, namely, aluminum (Al) oxide decorated tea waste (Tea-Al), was successfully prepared. The Tea-Al biosorbent was characterized by energy-dispersive spectrometry, Fourier transform infrared spectroscopy, powder X-ray diffraction and X-ray photoelectron spectroscopic analysis. The Tea-Al sample exhibited remarkably selective adsorption for fluoride (52.90%), but a weaker adsorption for other major constituents of brick tea infusion, such as catechins, polyphenols and caffeine, under the same conditions. Fluoride adsorption by Tea-Al for different times obeyed the surface reaction and adsorption isotherms fit the Freundlich model. In addition, the fluoride adsorption mechanism appeared to be an ion exchange between hydroxyl and fluoride ions. Results from this study demonstrated that Tea-Al is a promising biosorbent useful for the removal of fluoride in brick tea infusion. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Synthesis of magnetic activated carbon/α-Fe2O3 nanocomposite and its application in the removal of acid yellow 17 dye from water.

PubMed

Ranjithkumar, V; Sangeetha, S; Vairam, S

2014-05-30

The adsorption of acid yellow 17 dye on activated carbon/α-Fe2O3 nanocomposite prepared by simple pyrolytic method using iron(II) gluconate was investigated by batch technique. The composite was characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), and vibrating sample magnetometry (VSM). The size of iron oxide nanoparticles formed from iron(II) gluconate precursor is in the range 5-17nm. The saturation magnetization (Ms), remanence (Mr) and coercivity (Hc) of the magnetic carbon nanocomposite is 5.6emu/g, 1.14emu/g and 448Oe, respectively. The adsorption data are found to fit well with Langmuir and, fairly well with Freundlich and Tempkin isotherms at higher concentration of dye (40-100mg/L). Kinetics data indicate that the adsorption of dye follows pseudo-second order kinetics model. Copyright © 2014 Elsevier B.V. All rights reserved.

Exceptional selectivity for dissolved silicas in industrial waters using mixed oxides

DOE PAGES

Sasan, Koroush; Brady, Patrick V.; Krumhansl, James L.; ...

2017-11-07

The removal of silica, ubiquitous in produced and industrial waters, by novel mixed oxides is investigated in this present study. We have combined the advantage of high selectivity hydrotalcite (HTC, (Mg 6Al 2(OH) 16(CO 3)·4H 2O)), with large surface area of active alumina (AA, (Al 2O 3)) for effective removing of the dissolved silica from cooling tower water. The batch test results indicated the combined HTC/AA is a more effective method for removing silica from CTW than using each of HTC or AA separately. The silica uptake was confirmed by Fourier transform infrared (FTIR), and Energy dispersive spectroscopy (EDS). Ourmore » results indicate HTC/AA effectively removes silica from cooling tower water (CTW), even in the presence of large concentrations of competing anions, such as Cl -, NO 3 - HCO 3 -, CO 3 2- and SO 4 2-. The Single Path Flow Through (SPFT) tests confirmed to rapid uptake of silica by combined HTC/AA during column filtration. The experimental data of silica adsorption fit best to Freundlich isotherm model.« less

Adsorption of aqueous Cd(II) and Pb(II) on activated carbon nanopores prepared by chemical activation of doum palm shell.

PubMed

Gaya, Umar Ibrahim; Otene, Emmanuel; Abdullah, Abdul Halim

2015-01-01

Non-uniformly sized activated carbons were derived from doum palm shell, a new precursor, by carbonization in air and activation using KOH, NaOH and ZnCl2. The activated carbon fibres were characterised by X-ray diffraction, N2 adsorption-desorption, scanning electron microscopy, particle size analysis and evaluated for Cd(II) and Pb(II) removal. The 40-50 nm size, less graphitic, mesoporous NaOH activated carbon yielded high adsorption efficiency, pointing largely to the influence surface area. The performance of the KOH based activated carbon was arguably explained for the first time in terms of crystallinity. The efficiencies of the mesoporous ZnCl2-formulated activated carbon diminished due to the presence of larger particles. Batch adsorption of divalent metals revealed dependence on adsorbent dose, agitation time, pH and adsorbate concentrations with high adsorption efficiencies at optimum operating parameters. The equilibrium profiles fitted Langmuir and Freundlich isotherms, and kinetics favoured pseudo-second order model. The study demonstrated the practicability of the removal of alarming levels of cadmium and lead ions from industrial effluents.

Removal of Trace Arsenic to Meet Drinking Water Standards Using Iron Oxide Coated Multiwall Carbon Nanotubes

PubMed Central

Ntim, Susana Addo; Mitra, Somenath

2011-01-01

This study presents the removal of trace level arsenic to meet drinking water standards using an iron oxide-multi-walled carbon nanotube (Fe-MWCNT) hybrid as a sorbent. The synthesis was facilitated by the high degree of nanotube functionalization using a microwave assisted process, and a controlled assembly of iron oxide was possible where the MWCNT served as an effective support for the oxide. In the final product, 11 % of the carbon atoms were attached to Fe. The Fe-MWCNT was effective in arsenic removal to below the drinking water standard levels of 10 µg L−1. The absorption capacity of the composite was 1723 µg g−1 and 189 µg g−1 for As(III) and As(V) respectively. The adsorption of As(V) on Fe-MWCNT was faster than that of As(III). The pseudo-second order rate equation was found to effectively describe the kinetics of arsenic adsorption. The adsorption isotherms for As(III) and As(V) fitted both the Langmuir and Freundlich models. PMID:21625394

Box-Behnken methodology for Cr (VI) and leather dyes removal by an eco-friendly biosorbent: F. vesiculosus.

PubMed

Cobas, M; Sanromán, M A; Pazos, M

2014-05-01

This study focused on leather industrial effluents treatment by biosorption using Fucus vesiculosus as low-cost adsorbent. These effluents are yellowish-brown color and high concentration of Cr (VI). Therefore, biosorption process was optimized using response surface methodology based on Box-Behnken design operating with a simulated leather effluent obtained by mixture of Cr (VI) solution and four leather dyes. The key variables selected were initial solution pH, biomass dosage and CaCl2 concentration in the pretreatment stage. The statistical analysis shows that pH has a negligible effect, being the biomass dosage and CaCl2 concentration the most significant variables. At optimal conditions, 98% of Cr (VI) and 88% of dyes removal can be achieved. Freundlich fitted better to the obtained equilibrium data for all studied systems than Temkin, Langmuir or D-R models. In addition, the use of the final biosorbent as support-substrate to grown of enzyme producer fungi, Pleurotus ostreatus, was also demonstrated. Copyright © 2014 Elsevier Ltd. All rights reserved.

Exceptional selectivity for dissolved silicas in industrial waters using mixed oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sasan, Koroush; Brady, Patrick V.; Krumhansl, James L.

The removal of silica, ubiquitous in produced and industrial waters, by novel mixed oxides is investigated in this present study. We have combined the advantage of high selectivity hydrotalcite (HTC, (Mg 6Al 2(OH) 16(CO 3)·4H 2O)), with large surface area of active alumina (AA, (Al 2O 3)) for effective removing of the dissolved silica from cooling tower water. The batch test results indicated the combined HTC/AA is a more effective method for removing silica from CTW than using each of HTC or AA separately. The silica uptake was confirmed by Fourier transform infrared (FTIR), and Energy dispersive spectroscopy (EDS). Ourmore » results indicate HTC/AA effectively removes silica from cooling tower water (CTW), even in the presence of large concentrations of competing anions, such as Cl -, NO 3 - HCO 3 -, CO 3 2- and SO 4 2-. The Single Path Flow Through (SPFT) tests confirmed to rapid uptake of silica by combined HTC/AA during column filtration. The experimental data of silica adsorption fit best to Freundlich isotherm model.« less

[Pilot study on pentavalent arsenic removal by coagulation and the strengthening effect of flocs recycling].

PubMed

Yao, Juan-Juan; Gao, Nai-Yun; Xia, Sheng-Ji; Chen, Bei-Bei

2009-06-15

The pilot and bench scale studies on pentavalent arsenic removal by coagulation and the strengthening effect of flocs recycling were performed. The results show that above 95% As (V) in the raw water exists in the form of dissolved As (V). Furthermore, the removal efficiencies of dissolved arsenic and total arsenic by mixing, first flocculation, second flocculation, sedimentation, filtration units were 87.92%, 6.18%, 2.38%, 1.55%, 1.23% and 1.10%, 1.83%, 2.20%, 86.42%, 7.38% respectively. Therefore, conversion rate of dissolved As(V) into particulate As(V) and the settlement performance of flocs were strongly dependent on the coagulation effect, which determined the As(V) removal efficiency in the whole system. Flocs have a strong adsorption capacity for As(V) and the adsorption obeys a second order reaction kinetics and well fits the modified Freundlich model. Flocs recycling can obviously promoted the As(V) removal by enhanced coagulation and reduce the dosage of coagulant with recycling point set at rapid mixed site and recycling ratio at 50%.

Batch and fixed bed adsorption of levofloxacin on granular activated carbon from date (Phoenix dactylifera L.) stones by KOH chemical activation.

PubMed

Darweesh, Teeba M; Ahmed, Muthanna J

2017-03-01

Granular activated carbon (KAC) was prepared from abundant Phoenix dactylifera L. stones by microwave- assisted KOH activation. The characteristics of KAC were tested by pore analyses, scanning electron microscopy (SEM) and Fourier transforms infrared spectroscopy (FTIR). The adsorption behavior of levofloxacin (LEV) antibiotic on KAC with surface area of 817m 2 /g and pore volume of 0.638cm 3 /g were analyzed using batch and fixed bed systems. The equilibrium data collected by batch experiments were well fitted with Langmuir compared to Freundlich and Temkin isotherms. The effect of flow rate (0.5-1.5ml/min), bed height (15-25cm), and initial LEV concentration (75-225mg/l) on the behavior of breakthrough curves was explained. The fixed bed analysis showed the better correlation of breakthrough data by both Thomas and Yoon-Nelson models. High LEV adsorption capacity of 100.3mg/g was reported on KAC, thus being an efficient adsorbent for antibiotic pollutants to protect ecological systems. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of ɣ and ultrasonic irradiations on the physicochemical properties of CeO2-Fe2O3-Al2O3 for textile dyes removal applications

NASA Astrophysics Data System (ADS)

Ibrahim, Marwa M.; El-Molla, Sahar A.; Ismail, Sahar A.

2018-04-01

In this study highly effective adsorbent ternary mixed oxide CeO2-Fe2O3-Al2O3 was prepared by precipitation method. Various methods used to treat the mixed hydroxide like calcination, ultrasonic, hydrothermal and ɣ radiation with different doses to obtain the ternary mixed oxide. XRD, TEM, EDX, FTIR and SBET are used to study the physicochemical properties of nanoparticles. The CFAH and CFAɣ0.8 have the different morphologies and high surface area. Batch adsorption experiments were performed to remove anionic Remazol Red RB-133 dye. The experimental data showed that The CFAH and CFAɣ0.8 have high adsorption rate for removing of dye. The removal of dye is enhanced by ultrasonic radiation and high temperature. The adsorption process was fitted well for pseudo second order kinetics and followed the Freundlich isotherm model. In addition to, Thermodynamic results of adsorption process displayed that, the adsorption of dye on adsorbent was spontaneous, endothermic and chemisorptions process.

Adsorption and desorption characteristics of methamphetamine, 3,4-methylenedioxymethamphetamine, and pseudoephedrine in soils.

PubMed

Pal, Raktim; Megharaj, Mallavarapu; Kirkbride, K Paul; Naidu, Ravi

2015-06-01

This work presents, for the first time, information on the adsorption-desorption characteristics of illicit drugs and precursors in soils and an estimation of their potential bioavailability. The experiment was conducted using a batch equilibrium technique for the parent drugs methamphetamine and 3,4-methylenedioxymethamphetamine (MDMA) and the precursor pseudoephedrine in three South Australian soils varying in physiochemical properties. The individual compounds exhibited different adsorption mechanisms in the test soils, and the results fitted better with the Freundlich isotherm model (r (2) ≥ 0.99). The maximum adsorption capacity was recorded for pseudoephedrine (2,000 μg g(-1)). However, pseudoephedrine recorded lower organic carbon normalized adsorption coefficient values (<250 mL g(-1)), lower magnitudes of Gibb's free energy change, and higher percent desorption (73-92 %) compared to methamphetamine and MDMA. The results thus showed pseudoephedrine to be the most mobile compound in the soils under study, to have the highest availability for degradation of the three compounds, and to have the highest susceptibility to biotic degradation in test soils.

Biosorption of landfill leachate by Phanerochaete sp. ISTL01: isotherms, kinetics and toxicological assessment.

PubMed

Ghosh, Pooja; Thakur, Indu Shekhar

2017-07-01

The study investigates the ability of fungus Phanerochaete sp. ISTL01 for biosorption of color from landfill leachate. Batch mode experiments were conducted to study the effects of pH, temperature, adsorbent dose, contact time and initial leachate concentration on biosorption. Maximum biosorption capacity was determined as 17.73 mg g -1 of biomass. Equilibrium isotherms and kinetics were further studied. The biosorption data were found to fit well to the Freundlich isotherm and pseudo-second-order kinetic model. The value of activation energy suggested that chemisorption mechanism was involved. Biosorption efficiency was also evaluated by the Methyltetrazolium (MTT) assay for cytotoxicity and alkaline comet assay in HepG2 human hepato-carcinoma cells. The fungus reduced toxicity as shown by 1.3-fold increase in MTT EC 50 and 1.5- and 1.1-fold reduction in Tail moment and Olive tail moment, respectively, after 12 h biosorption. The fungus showed good biosorption characteristics in terms of contaminant-level reduction per unit mass of adsorbent, process kinetics and toxicity reduction, envisaging its application in leachate treatment.

Biosensor-assisted selection of optimal parameters for designing molecularly imprinted polymers selective to phosmet insecticide.

PubMed

Aftim, Nadin; Istamboulié, Georges; Piletska, Elena; Piletsky, Sergey; Calas-Blanchard, Carole; Noguer, Thierry

2017-11-01

Molecularly imprinted polymers (MIPs) for phosmet insecticide were synthesized by batch polymerization. The affinity of functional monomers to phosmet was tested using an original method involving an electrochemical biosensor based on acetylcholinesterase inhibition. It was demonstrated that association of phosmet with appropriate functional monomers resulted in a decrease of enzyme inhibition. Using this method, it was shown that N,N-methylenebis(acrylamide) displayed the highest interactions with phosmet using DMSO as solvent. These results were in good accordance with those obtained by conventional computational modeling. Molecularly imprinted polymers (MIPs) and non-imprinted polymers (NIPs) were synthesized and adsorption isotherms were studied to describe their interaction with phosmet. Freundlich isotherm was able to fit phosmet adsorption on MIPs with good agreement (R 2 = 0.9). The pre-exponential factor K F determined for MIPs was 1.439mg (1-N) g -1 L N , more that 10 times higher than for NIPs (0.125mg (1-N) g -1 . L N ), indicating an increase of binding sites number and average affinity. Copyright © 2017 Elsevier B.V. All rights reserved.

Quantitative structure property relationships for the adsorption of pharmaceuticals onto activated carbon.

PubMed

Dickenson, E R V; Drewes, J E

2010-01-01

Isotherms were determined for the adsorption of five pharmaceutical residues, primidone, carbamazepine, ibuprofen, naproxen and diclofenac, to Calgon Filtrasorb 300 powdered activated carbon (PAC). The sorption behavior was examined in ultra-pure and wastewater effluent organic matter (EfOM) matrices, where more sorption was observed in the ultra-pure water for PAC doses greater than 10 mg/L suggesting the presence of EfOM hinders the sorption of the pharmaceuticals to the PAC. Adsorption behaviors were described by the Freundlich isotherm model. Quantitative structure property relationships (QSPRs) in the form of polyparameter linear solvation energy relationships were developed for simulating the Freundlich adsorption capacity in both ultra-pure and EfOM matrices. The significant 3D-based descriptors for the QSPRs were the molar volume, polarizability and hydrogen-bond donor parameters.

Experimental design based response surface methodology optimization of ultrasonic assisted adsorption of safaranin O by tin sulfide nanoparticle loaded on activated carbon.

PubMed

Roosta, M; Ghaedi, M; Daneshfar, A; Sahraei, R

2014-03-25

In this research, the adsorption rate of safranine O (SO) onto tin sulfide nanoparticle loaded on activated carbon (SnS-NPAC) was accelerated by the ultrasound. SnS-NP-AC was characterized by different techniques such as SEM, XRD and UV-Vis measurements. The present results confirm that the ultrasound assisted adsorption method has remarkable ability to improve the adsorption efficiency. The influence of parameters such as the sonication time, adsorbent dosage, pH and initial SO concentration was examined and evaluated by central composite design (CCD) combined with response surface methodology (RSM) and desirability function (DF). Conducting adsorption experiments at optimal conditions set as 4 min of sonication time, 0.024 g of adsorbent, pH 7 and 18 mg L(-1) SO make admit to achieve high removal percentage (98%) and high adsorption capacity (50.25 mg g(-)(1)). A good agreement between experimental and predicted data in this study was observed. The experimental equilibrium data fitting to Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich models show that the Langmuir model is a good and suitable model for evaluation and the actual behavior of adsorption. Kinetic evaluation of experimental data showed that the adsorption processes followed well pseudo-second-order and intraparticle diffusion models. Copyright © 2013. Published by Elsevier B.V.

Functional polyaniline/multiwalled carbon nanotube composite as an efficient adsorbent material for removing pharmaceuticals from aqueous media.

PubMed

Dutra, Flávia Viana Avelar; Pires, Bruna Carneiro; Nascimento, Tienne Aparecida; Borges, Keyller Bastos

2018-09-01

The composite polyaniline/multiwalled carbon nanotube (PAni/MWCNT, 1:0.1 w/w) was developed with the intention of binding the adsorbent properties of two materials and using it to adsorb pharmaceuticals from aqueous media. PAni/MWCNT was characterized by scanning electron microscopy, thermogravimetry, infrared spectroscopy, pH at the point of zero charge, and the effect on the surface wettability of the material. As proof of concept, adsorption studies were carried out using meloxicam (MLX) as the pharmaceutical and it was evaluated as a function of pH, temperature, ionic strength, contact time and variation in concentration. Kinetics and isothermal models were applied to evaluate the mechanism of the adsorption process. The best MLX adsorption result was at pH 2 with 6 min of contact with PAni/MWCNT. The kinetics models that fitted the experimental data were pseudo-second order and Elovich and the kinetics model was the dual-site Langmuir-Freundlich. Both models suggest that the adsorption occurs by the chemical nature of the surface and in the pores of the energetically heterogeneous composite. The PAni/MWCNT presented an adsorption capacity of 221.2 mg g -1 , a very good value when compared with the literature and can be used to remove pharmaceuticals from aqueous environments. Copyright © 2018 Elsevier Ltd. All rights reserved.

Trichoderma sp. spores and Kluyveromyces marxianus cells magnetic separation: Immobilization on chitosan-coated magnetic nanoparticles.

PubMed

Palacios-Ponce, Sócrates; Ramos-González, Rodolfo; Ruiz, Héctor A; Aguilar, Miguel A; Martínez-Hernández, José L; Segura-Ceniceros, Elda P; Aguilar, Cristóbal N; Michelena, Georgina; Ilyina, Anna

2017-07-03

In the present study, the interactions between chitosan-coated magnetic nanoparticles (C-MNP) and Trichoderma sp. spores as well as Kluyveromyces marxianus cells were studied. By Plackett-Burman design, it was demonstrated that factors which directly influenced on yeast cell immobilization and magnetic separation were inoculum and C-MNP quantity, stirring speed, interaction time, and volume of medium, while in the case of fungal spores, the temperature also was disclosed as an influencing factor. Langmuir and Freundlich models were applied for the mathematical analysis of adsorption isotherms at 30°C. For Trichoderma sp. spore adsorption isotherm, the highest correlation coefficient was observed for lineal function of Langmuir model with a maximum adsorption capacity at 5.00E + 09 spores (C-MNP g -1 ). Adsorption isotherm of K. marxianus cells was better adjusted to Freundlich model with a constant (K f ) estimated as 2.05E + 08 cells (C-MNP g -1 ). Both systems may have a novel application in fermentation processes assisted with magnetic separation of biomass.

Adsorption of an anionic dye on a novel low-cost mesoporous adsorbent: kinetic, thermodynamic and isotherm studies

NASA Astrophysics Data System (ADS)

Msaad, Asmaa; Belbahloul, Mounir; Zouhri, Abdeljalil

2018-05-01

Our activated carbon was prepared successfully using phosphoric acid as an activated agent. The activated carbon was characterized by Scanning Electron Micrograph (SEM), Brunauer-Emmett- Teller (BET), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). The aim of our study is to evaluate the adsorption capacity of Methyl Orange (MO) on Ziziphus lotus activated carbon. Adsorption isotherms were studied according to Langmuir and Freundlich Model, and adsorption kinetics according to pseudo-first and second-order. Results show that the maximum adsorption was reached in the first 10min at ambient temperature with a yield of 96.31%. The Langmuir isotherm shows a correlation coefficient of 99.4 % higher than Freundlich model and the adsorption kinetic model follow a pseudo-second-order with a maximum adsorption capacity of 769.23 mg/g. FTIR and X-Ray spectroscopy indicate that our activated carbon has an amorphous structure with the presence of functional groups, where BET analysis revealed a high surface area of 553 mg/g, which facilitate the adsorption process

Adsorption of Copper Ion using Acrylic Acid-g-Polyaniline in Aqueous Solution

NASA Astrophysics Data System (ADS)

Kamarudin, Sabariah; Mohammad, Masita

2018-04-01

A conductive polymer, polyaniline (PANI) has unique electrical behaviour, stable in the environment, easy synthesis and have wide application in various fields. Modification of PANI in order to improve its adsorption capacity has been done. In this study, the polyaniline-grafted acrylic acid has been prepared and followed by adsorption of copper ion in aqueous solution. Acrylic acid, PANI and acrylic acid-g-polyaniline (Aag-PANI) were characterized by FTIR and SEM to determine its characteristic. The adsorption capacity was investigated to study the removal capacity of Cu ion from aqueous solution. Two parameters were selected which are pH (2, 4 and 6) and initial metal ion concentration (50 mg/L, 100 mg/L and 200 mg/L). The maximum adsorption capacity for PANI and Aag-PANI are 1.7 mg/g and 64.6 mg/g, respectively, at an initial concentration of 100 mg/L. The Langmuir adsorption isotherm model and Freundlich adsorption isotherm model have been used and showed that it is heterolayer adsorption by follows the Freundlich isotherm model.

Adsorption of Pd(II) complexes from chloride solutions obtained by leaching chlorinated spent automotive catalysts on ion exchange resin Diaion WA21J.

PubMed

Shen, Shaobo; Pan, Tonglin; Liu, Xinqiang; Yuan, Lei; Zhang, Yongjian; Wang, Jinchao; Guo, Zhanchen

2010-05-01

It was found that Rh, Pd and Pt contained in the spent ceramic automotive catalysts could be effectively extracted by dry chlorination with chlorine. In order to concentrate Pd(II) contained in the chloride solution obtained from the dry chlorination process, thermodynamic and kinetics studies for adsorption of Pd(II) complexes from the chloride solutions on anionic exchange resin Diaion WA21J were carried out. It was found that Pd, Pt, Rh, Al, Fe, Si, Zn and Pb from the chloride solution could be adsorbed on the resin. The isothermal adsorption of Pd(II) was found to fit Freundlich, Langmuir and Dubinin-Kaganer-Radushkevich models under the adsorption conditions. The adsorption of Pd(II) on the resin was favorable according to the values of 1/n and R(L) from Freundlich and Langmuir adsorption isotherms, respectively. The maximum monolayer adsorption capacities Q(max) based on Langmuir adsorption isotherms were 5.70, 4.84 and 4.05 mg/g and the corresponding value X(m) based on Dubinin-Kaganer-Radushkevich were 5.55, 4.69 and 4.01 mg/g at temperatures 18 degrees C, 28 degrees C and 40 degrees C, respectively. The apparent adsorption energies (E(ad)) based on Dubinin-Kaganer-Radushkevich isotherm were -15.43, -16.22 and -23.57 kJ/mol for the temperatures 18 degrees C, 28 degrees C and 40 degrees C, respectively. Chemical adsorption was a main mechanism involved in the adsorption process. Pd(II) adsorption on the resin could be accelerated by increasing the adsorption temperature. The adsorption of Pd(II) from the chloride solution on the resin underwent pseudo-first order kinetic process and the apparent adsorption activation energy E(a) was 15.0 kJ/mol. The intra-particle diffusion was a main rate controlling step in the Pd(II) adsorption process under the adsorption conditions. Copyright 2010 Elsevier Inc. All rights reserved.

Zeolite in horizontal permeable reactive barriers for artificial groundwater recharge

NASA Astrophysics Data System (ADS)

Leal, María; Martínez-Hernández, Virtudes; Lillo, Javier; Meffe, Raffaella; de Bustamante, Irene

2013-04-01

The Spanish Water Reuse Royal Decree 1620/2007 considers groundwater recharge as a feasible use of reclaimed water. To achieve the water quality established in the above-mentioned legislation, a tertiary wastewater treatment is required. In this context, the infiltration of effluents generated by secondary wastewater treatments through a Horizontal Permeable Reactive Barrier (HPRB) may represent a suitable regeneration technology. Some nutrients (phosphate and ammonium) and some Pharmaceutical and Personal Care Products (PPCPs) are not fully removed in conventional wastewater treatment plants. To avoid groundwater contamination when effluents of wastewater treatments plants are used in artificial recharge activities, these contaminants have to be removed. Due to its sorption capacities, zeolite is among the most used reactive materials in Permeable Reactive Barrier (PRB). Therefore, the main goal of this study is to evaluate the zeolite retention effectiveness of nutrients and PPCPs occurring in treated wastewater. Batch sorption experiments using synthetic wastewater (SWW) and zeolite were performed. A 1:4 zeolite/SWW ratio was selected due to the high sorption capacity of the reactive material.The assays were carried out by triplicate. All the bottles containing the SWW-zeolite mixture were placed on a mechanical shaker during 24 hours at 140 rpm and 25 °C. Ammonium and phosphate, as main nutrients, and a group of PPCPs were selected as compounds to be tested during the experiments. Nutrients were analyzed by ion chromatography. For PPCPs determination, Solid Phase Extraction (SPE) was applied before their analysis by liquid chromatography-mass spectrometry time of flight (LC-MS/ TOF). The experimental data were fitted to linearized Langmuir and Freundlich isotherm equations to obtain sorption parameters. In general, Freundlich model shows a greater capability of reproducing experimental data. To our knowledge, sorption of the investigated compounds on zeolite has rarely been addressed and this holds true especially for PPCPs. Therefore, the obtained results will be useful for the design and characterization of those HPRBs in which zeolite will be employed to regenerate treated wastewater for artificial recharge activities.

Removal of Cd(II), Pb(II) and Cr(III) from water using modified residues of Anacardium occidentale L.

NASA Astrophysics Data System (ADS)

Coelho, Gustavo Ferreira; Gonçalves, Affonso Celso; Schwantes, Daniel; Rodríguez, Esperanza Álvarez; Tarley, César Ricardo Teixeira; Dragunski, Douglas; Conradi Junior, Élio

2018-06-01

The pollution of water has been one of the greatest problems faced by the modern society, due to industrialization and urban growth. Rivers, lakes and seas have been continually suffering from the rising concentration of various pollutants, especially toxic elements. This study aimed to evaluate the use of cashew nut shell ( Anacardium occidentale) (CNS), after chemical modification with H2O2, H2SO4 and NaOH, as an new and renewable adsorbent material, for the removal of metals Cd2+, Pb2+ and Cr3+ in aqueous medium. The adsorbents were characterized by its chemical constitution, structure, infrared spectroscopy, morphology, by means of scanning electron microscopy, determination of the point of zero charge, thermogravimetrical analysis and porosimetry assessments. Tests were conducted to determine the optimal conditions (pH vs. adsorbent mass) for adsorption, by means of multivariate analysis using a central composite design. The adsorption kinetics was evaluated by models of pseudo-first order, pseudo-second order, Elovich and intraparticle diffusion, while adsorption isotherms were linearized by Langmuir, Freundlich and Dubinin-Radushkevich. The effect of initial concentration, temperature and desorption was also performed. The adsorbents exhibited irregular, spongy and heterogeneous structure. FTIR analysis confirms the presence of hydroxyl, aliphatic, phenolic and carboxylic acid groups, which are favorable adsorption characteristics. The pHPZC of adsorbent is 4.35, 2.50 e 6.92, respectively, for CNS H2O2, H2SO4 and NaOH. The optimum adsorption conditions were as follows: pH 5.0; relation of adsorbent mass/volume of water: 4 g L-1; 40 min of contact time for reaching the equilibration. Results suggest the predominance of chemisorption of Cd2+ and Cr3+. Most of biosorbents exhibited good fit by Langmuir and Freundlich, suggesting the occurrence of adsorption on mono- and multilayers. The adsorbents of cashew nut shell exhibited high removal efficiency of Cd, Pb and Cr from waters.

Tylosin sorption to diatomaceous earth described by Langmuir isotherm and Freundlich isotherm models

USDA-ARS?s Scientific Manuscript database

Tylosin, an antibiotic used for livestock, is a macrolide structurally similar to a number of important, often prescribed human antibiotics. Because of this relationship, tylosin presents a potential threat of antimicrobial resistance from environmental buildup. This work investigated tylosin sorpti...

Isothermal approach to predict the removal efficiency of β-carotene adsorption from CPO using activated carbon produced from tea waste

NASA Astrophysics Data System (ADS)

Harahap, S. A. A.; Nazar, A.; Yunita, M.; Pasaribu, RA; Panjaitan, F.; Yanuar, F.; Misran, E.

2018-02-01

Adsorption of β-carotene in crude palm oil (CPO) was studied using activated carbon produced from tea waste (ACTW) an adsorbent. Isothermal studies were carried out at 60 °C with the ratio of activated carbon to CPO were 1:3, 1:4, 1:5, and 1:6, respectively. The ACTW showed excellent performance as the percentage of adsorption of β-carotene from CPO was > 99%. The best percentage removal (R) was achieved at ACTW to CPO ratio equal to 1:3, which was 99.61%. The appropriate isotherm model for this study was Freundlich isotherm model. The combination of Freundlich isotherm equation and mass balance equation showed a good agreement when validated to the experimental data. The equation subsequently executed to predict the removal efficiency under given sets of operating conditions. At a targetted R, CPO volume can be estimated for a certain initial concentration β-carotene in CPO C0 and mass of ACTW adsorbent M used.

Adsorption of arsenic(V) by iron-oxide-coated diatomite (IOCD).

PubMed

Pan, Yi-Fong; Chiou, Cary T; Lin, Tsair-Fuh

2010-09-01

PURPOSES AND AIMS: Economically efficient methods for removing arsenic from the drinking water supply are urgently needed in many parts of the world. Iron oxides are known to have a strong affinity for arsenic in water. However, they are commonly present in the forms of fine powder or floc, which limits their utility in water treatment. In this study, a novel granular adsorbent, iron-oxide-coated diatomite (IOCD), was developed and examined for its adsorption of arsenic from water. An industrial-grade diatomite was used as the iron oxide support. The diatomite was first acidified and dried and then coated with iron oxide up to five times. The prepared IOCD samples were characterized for their morphology, composition, elemental content, and crystal properties by various instruments. Experiments of equilibrium and kinetic adsorption of As(V) on IOCD were conducted using 0.1- and 2-L polyethylene bottles, respectively, at different pH and temperatures. Iron oxide (alpha-Fe(2)O(3) hematite) coated onto diatomite greatly improves (by about 30 times) the adsorption of As(V) from water by IOCD as compared to using raw diatomite. This improvement was attributed to increases in both surface affinity and surface area of the IOCD. The surface area of IOCD increased to an optimal value. However, as the IOCD surface area (93 m(2)/g) was only 45% higher than that of raw diatomite (51 m(2)/g), the enhanced As(V) adsorption resulted primarily from the enhanced association of negatively charged As(V) ions with the partial positive surface charge of the iron oxide. The As(V) adsorption decreased when the solution pH was increased from 3.5 to 9.5, as expected from the partial charge interaction between As(V) and IOCD. The adsorption data at pH 5.5 and 7.5 could be well fitted to the Freundlich equation. A moderately high exothermic heat was observed for the As(V) adsorption, with the calculated molar isosteric heat ranging from -4 to -9 kcal/mol. The observed heats fall between those for physical adsorption and chemisorption and are indicative of the formation of a series of ion-pair complexes of As(V) ions with iron oxide surface groups. This study demonstrated that the granular IOCD was successfully developed and employed to remove the As(V) in aqueous solution. The Freundlich isotherm well fitted the equilibrium adsorption data of As(V) onto IOCD, and both the pseudo-second-order model and the pore diffusion model simulated well the adsorption kinetics. Compared to other iron-oxide-based adsorbents reported in the literatures, the adsorption capacity of IOCD is relatively high and its kinetics is fast.

Removal of р-nitrophenol from aqueous solution by magnetically modified activated carbon

NASA Astrophysics Data System (ADS)

Han, Shuai; Zhao, Feng; Sun, Jian; Wang, Bin; Wei, Rongyan; Yan, Shiqiang

2013-09-01

Activated carbon was modified with γ-Fe2O3 nanoparticles, using the chemical co-precipitation technique and the carboxylic acid vapor treatment technique. Two magnetic composites were characterized and compared by Fourier Transform Infrared spectroscopy, X-ray diffractometry, vibrating sample magnetometry and nitrogen adsorption-desorption. Then the two materials were used to remove p-nitrophenol in water. The equilibrium data revealed that the Langmuir isotherm was better in fitting the experiment result than the Freundlich isotherm, and the sorption capacity of the nanocomposite made by the chemical co-precipitation technique was higher than that of the other one. We suggest that the chemical co-precipitation technique is a more efficient and practical method to produce magnetically modified activated carbon.

Thermodynamics of Cadmium Sorption on Different Soils of West Bengal, India

PubMed Central

Paul, Ranjit Kumar; Das, D. K.; Boruah, Romesh K.; Sonar, Indira

2014-01-01

A sorption study was conducted on different soils collected from five agroecological zones of West Bengal, India, to understand the soil environmental behavior and fate of cadmium. For this purpose batch adsorption experiments were carried out at the native soil pH and at three different temperatures (25°C, 35°C, and 45°C). The adsorption data fitted by a linear least squares technique to the different sorption isotherms. Most data obtained give the good fit to both Freundlich and modified Langmuir isotherms, but they are not consistent with the linear Langmuir adsorption model. Thermodynamic parameters, namely, thermodynamics equilibrium constant at a particular temperature T  (K T 0), Gibbs free energy at a particular temperature T  (ΔG T 0), and change of enthalpy (ΔH 0) and change of entropy at temperature T  (ΔS T 0), were also determined by applying sorption value and concentrations of Cd in equilibrium solution within the temperature range. The thermodynamic parameters revealed that Cd sorption increases as the values of K T 0, ΔG T 0, ΔH 0, and ΔS T 0 were increased on reaction temperatures. The spontaneous sorption reaction can be concluded due to high values of ΔG T 0. The positive values of ΔH 0 indicated that the Cd sorption is an endothermic one. Under these present conditions, the soil and its components possibly supply a number of sites having different adsorption energies for cadmium sorption. PMID:24683322

Developmental Toxicity of Diclofenac and Elucidation of Gene Regulation in zebrafish (Danio rerio)

NASA Astrophysics Data System (ADS)

Chen, Jia-Bin; Gao, Hong-Wen; Zhang, Ya-Lei; Zhang, Yong; Zhou, Xue-Fei; Li, Chun-Qi; Gao, Hai-Ping

2014-05-01

Environmental pollution by emerging contaminants, e.g. pharmaceuticals, has become a matter of widespread concern in recent years. We investigated the membrane transport of diclofenac and its toxic effects on gene expression and the development of zebrafish embryos. The association of diclofenac with the embryos conformed to the general partition model at low concentration, the partition coefficient being 0.0033 ml per embryo. At high concentration, the interaction fitted the Freundlich model. Most of the diclofenac remained in the extracellular aqueous solution with less than 5% interacting with the embryo, about half of which was adsorbed on the membranes while the rest entered the cytoplasm. Concentrations of diclofenac over 10.13 μM were lethal to all the embryos, while 3.78 μM diclofenac was teratogenic. The development abnormalities at 4 day post treatment (dpt) include shorter body length, smaller eye, pericardial and body edema, lack of liver, intestine and circulation, muscle degeneration, and abnormal pigmentation. The portion of the diclofenac transferred into the embryo altered the expression of certain genes, e.g. down-regulation of Wnt3a and Gata4 and up-regulation of Wnt8a. The alteration of expression of such genes or the regulation of downstream genes could cause defects in the cardiovascular and nervous systems.

A novel biochar derived from cauliflower (Brassica oleracea L.) roots could remove norfloxacin and chlortetracycline efficiently.

PubMed

Qin, Tingting; Wang, Zhaowei; Xie, Xiaoyun; Xie, Chaoran; Zhu, Junmin; Li, Yan

2017-12-01

The biochar was prepared by pyrolyzing the roots of cauliflowers, at a temperature of 500 °C under oxygen-limited conditions. The structure and characteristics of the biochar were examined using scanning electron microscopy, an energy dispersive spectrometer, a zeta potential analyzer, and Fourier transform infrared spectroscopy. The effects of the temperature, the initial pH, antibiotic concentration, and contact time on the adsorption of norfloxacin (NOR) and chlortetracycline (CTC) onto the biochar were investigated. The adsorption kinetics of NOR and CTC onto the biochar followed the pseudo-second-order kinetic and intra-particle diffusion models. The adsorption isotherm experimental data were well fitted to the Langmuir and Freundlich isotherm models. The maximum adsorption capacities of NOR and CTC were 31.15 and 81.30 mg/g, respectively. There was little difference between the effects of initial solution pH (4.0-10.0) on the adsorption of NOR or CTC onto the biochar because of the buffering effect. The biochar could remove NOR and CTC efficiently in aqueous solutions because of its large specific surface area, abundant surface functional groups, and particular porous structure. Therefore, it could be used as an excellent adsorbent material because of its low cost and high efficiency and the extensive availability of the raw materials.

Porous nano-cerium oxide wood chip biochar composites for aqueous levofloxacin removal and sorption mechanism insights.

PubMed

Yi, Shengze; Sun, Yuanyuan; Hu, Xin; Xu, Hongxia; Gao, Bin; Wu, Jichun

2017-01-14

The adsorption removal of levofloxacin (LEV), a widely used fluoroquinolone antibiotic, by using the biochars derived from the pyrolysis of pine wood chip pretreated with cerium trichloride was investigated through batch sorption experiments and multiple characterization techniques. The differences in the basic physicochemical properties between Ce-impregnated biochars and the pristine biochars were confirmed by the analysis of elemental compositions, specific surface areas, energy dispersive spectrometry, X-ray diffraction, and thermo-gravimetry. FT-IR spectra of the pre- and post-sorption biochars confirmed the chemical adsorption for LEV sorption onto the biochars. Large shifts in the binding energy of Ce 3d , O 1s , C 1s , and N 1s regions on the pre- and post-sorption biochars indicated the surface complexation of LEV molecule onto the biochars. The binding species of Ce 4+ and Ce 3+ identified by X-ray photoelectron spectroscopy reflect the role of Ce oxides during sorption. Batch adsorption showed the significant enhancement of adsorption capacity for LEV after the Ce modification. Batch adsorption kinetic data fitted well with the pseudo-second-order model. Both the Langmuir and the Freundlich models reproduced the isotherm data well. Findings from this work indicated that Ce-impregnated biochars can be effective for the removal of aqueous LEV.

Effect of degree of deacetylation of chitosan on adsorption capacity and reusability of chitosan/polyvinyl alcohol/TiO2 nano composite.

PubMed

Habiba, Umma; Joo, Tan Chin; Siddique, Tawsif A; Salleh, Areisman; Ang, Bee Chin; Afifi, Amalina M

2017-11-01

The chitosan/polyvinyl alcohol/TiO 2 composite was synthesized. Two different degrees of deacetylation of chitosan were prepared by hydrolysis to compare the effectiveness of them. The composite was analyzed via field emission scanning electron microscopy, Fourier transform infrared, X-ray diffraction, thermal gravimetric analysis, weight loss test and adsorption study. The FTIR and XRD results proved the interaction among chitosan, PVA and TiO 2 without any chemical reaction. It was found that, chitosan with higher degree of deacetylation has better stability. Furthermore, it also showed that higher DD of chitosan required less time to reach equilibrium for methyl orange. The adsorption followed the pseudo-second-order kinetic model. The Langmuir and Freundlich isotherm models were fitted well for isotherm study. Adsorption capacity was higher for the composite containing chitosan with higher DD. The dye removal rate was independent of the dye's initial concentration. The adsorption capacity was increased with temperature and it was found from reusability test that the composite containing chitosan with higher DD is more reusable. It was notable that adsorption capacity was even after 15 runs. Therefore, chitosan/PVA/TiO 2 composite can be a very useful material for dye removal. Copyright © 2017 Elsevier B.V. All rights reserved.

Enhanced Defluoridation Capacity From Aqueous Media via Hydroxyapatite Decorated With Carbon Nanotube.

PubMed

Tang, Qingzi; Duan, Tongdan; Li, Peng; Zhang, Ping; Wu, Daishe

2018-01-01

In this work, the potential of a novel hydroxyapatite decorated with carbon nanotube composite (CNT-HAP) for fluoride removal was investigated. The synthesized CNT-HAP composite was systematically characterized by X-ray diffraction(XRD), Fourier Transform infrared spectroscopy(FTIR), scanning electron microscope (SEM) and Brunauer-Emmett-Teller(BET). Batch adsorption experiments were conducted to investigate the defluorination capacity of CNT-HAP. The CNT-HAP composite has a maximum adsorption capacity of 11.05 mg·g -1 for fluoride, and the isothermal adsorption data were fitted by the Freundlich model to calculate the thermodynamic parameters. Thermodynamic analysis implies that the adsorption of fluoride on CNT-HAP is a spontaneous process. Furthermore, the adsorption of fluoride follows pseudo-second-order model. The effects of solution pH, co-existing anions and reaction temperature on defluorination efficiency were examined to optimize the operation conditions for fluoride adsorption. It is found that the optimized pH-value for fluoride removal by CNT-HAP composite is 6. In addition, among five common anions studied in this work, the presence of [Formula: see text] and [Formula: see text] could considerably affect the fluoride removal by CNT-HPA in aqueous media. Finally, the underlying mechanism for the fluoride removal by CNT-HAP is analyzed, and an anion exchange process is proposed.

Microwave-assisted preparation of nitrogen-doped biochars by ammonium acetate activation for adsorption of acid red 18

NASA Astrophysics Data System (ADS)

Wang, Li; Yan, Wei; He, Chi; Wen, Hang; Cai, Zhang; Wang, Zixuan; Chen, Zhengzheng; Liu, Weifeng

2018-03-01

Nitrogen-doped biochars derived from Phragmites australis (PA) were prepared using ammonium chloride (AC) and ammonium acetate (AA) as nitrogen sources by phosphoric acid activation via microwave assisted treatment. Their physicochemical properties, acid red 18 (AR18) adsorption performance and possible mechanisms were systematically evaluated. Nitrogen was successfully doped onto the biochar's surface in the formation of pyrrole-N, pyridine-N and oxidized-N with pyridine-N being the major component (64%). The pHiep and basic foundational groups of the biochars increased consequently however their surface areas slightly decreased. The adsorption kinetic data were best fit to the pseudo-second order model and the equilibrium data were well simulated by Freundlich model for all biochars, indicating the important role of chemical interactions. The maximum AR18 adsorption capacities of PAB-AA and PAB-AC were 1.41 and 1.18 times higher compared with the non N-doped biochar, which were mainly attributed to the π-π EDA interaction between the pyridine-N and AR18 as revealed by the comparison of XPS analyses before and after AR18 adsorption. Meanwhile, other mechanisms such as pore filling effect, Lewis acid-base interaction, electrostatic attraction and hydrogen bonding also existed as demonstrated by BET, XPS and FTIR analyses.

Enhanced defluoridation capacity from aqueous media via hydroxyapatite decorated with carbon nanotube

NASA Astrophysics Data System (ADS)

Tang, Qingzi; Duan, Tongdan; Li, Peng; Zhang, Ping; Wu, Daishe

2018-04-01

In this work, the potential of a novel carbon nanotube-doped hydroxyapatite composite (CNT-HAP) for fluoride removal was investigated. The synthesized CNT-HAP composite was systematically characterized by X-ray diffraction(XRD), Fourier Transform infrared spectroscopy(FTIR), scanning electron microscope (SEM) and Brunauer–Emmett–Teller(BET). Batch adsorption experiments were conducted to investigate the defluorination capacity of CNT-HAP. The CNT-HAP composite has a maximum adsorption capacity of 11.05 mg·g-1 for fluoride, and the isothermal adsorption data were fitted by the Freundlich model to calculate the thermodynamic parameters. Thermodynamic analysis implies that the adsorption of fluoride on CNT-HAP is a spontaneous process. Furthermore, the adsorption of fluoride follows pseudo-second-order model. The effects of solution pH, co-existing anions and reaction temperature on defluorination efficiency were examined to optimize the operation conditions for fluoride adsorption. It is found that the optimized pH value for fluoride removal by CNT-HAP composite is 6. In addition, among five common anions studied in this work, the presence of HCO3- and PO43- could considerably affect the fluoride removal by CNT-HPA in aqueous media. Finally, the underlying mechanism for the fluoride removal by CNT-HAP is analysed, and an anion exchange process is proposed.

Enhanced Defluoridation Capacity From Aqueous Media via Hydroxyapatite Decorated With Carbon Nanotube

PubMed Central

Tang, Qingzi; Duan, Tongdan; Li, Peng; Zhang, Ping; Wu, Daishe

2018-01-01

In this work, the potential of a novel hydroxyapatite decorated with carbon nanotube composite (CNT-HAP) for fluoride removal was investigated. The synthesized CNT-HAP composite was systematically characterized by X-ray diffraction(XRD), Fourier Transform infrared spectroscopy(FTIR), scanning electron microscope (SEM) and Brunauer–Emmett–Teller(BET). Batch adsorption experiments were conducted to investigate the defluorination capacity of CNT-HAP. The CNT-HAP composite has a maximum adsorption capacity of 11.05 mg·g−1 for fluoride, and the isothermal adsorption data were fitted by the Freundlich model to calculate the thermodynamic parameters. Thermodynamic analysis implies that the adsorption of fluoride on CNT-HAP is a spontaneous process. Furthermore, the adsorption of fluoride follows pseudo-second-order model. The effects of solution pH, co-existing anions and reaction temperature on defluorination efficiency were examined to optimize the operation conditions for fluoride adsorption. It is found that the optimized pH-value for fluoride removal by CNT-HAP composite is 6. In addition, among five common anions studied in this work, the presence of HCO3- and PO43- could considerably affect the fluoride removal by CNT-HPA in aqueous media. Finally, the underlying mechanism for the fluoride removal by CNT-HAP is analyzed, and an anion exchange process is proposed. PMID:29696138

Biosorption of Hexavalent Chromium from Aqueous Medium with Opuntia Biomass

PubMed Central

2014-01-01

The biosorption of hexavalent chromium from aqueous solutions by Opuntia cladodes and ectodermis from cactus fruits was investigated. Both types of biomass are considered low-cost, natural, and ecofriendly biosorbents. Batch experiments were carried out to determine Cr(VI) biosorption capacity and the efficiency of the biosorption process under different pH, initial Cr(VI) concentration, and sorbent dosage. The biosorption of Cr(VI) by Opuntia biomass was highly pH dependent, favoring higher metal uptake at low pH. The higher biosorption capacity was exhibited at pH 2. The optimal conditions were obtained at a sorbent dosage of 1 g L−1 and initial metal concentration of 10 mg L−1. Biosorption kinetic data were properly fitted with the pseudo-second-order kinetic model. The rate constant, the initial biosorption rate, and the equilibrium biosorption capacity were determined. The experimental equilibrium data obtained were analyzed using two-parameter isotherm models (Langmuir, Freundlich, and Temkin). The Langmuir maximum monolayer biosorption capacity (q max) was 18.5 mg g−1 for cladodes and 16.4 mg g−1 for ectodermis. The results suggest that Opuntia biomass could be considered a promising low-cost biosorbent for the ecofriendly removal of Cr(VI) from aqueous systems. PMID:24982975

Adsorption studies on the removal of COD and BOD from treated sewage using activated carbon prepared from date palm waste.

PubMed

Nayl, Abd ElAziz A; Elkhashab, Reda A; El Malah, Tamer; Yakout, Sobhy M; El-Khateeb, Mohamed A; Ali, Mahmoud M S; Ali, Hazim M

2017-10-01

In this work, the adsorption of chemical oxygen demand (COD) and biological oxygen demand (BOD) from treated sewage with low-cost activated carbon prepared from date palm shell waste by chemical activation method was studied. Different parameters affecting the adsorption process such as carbon dose, pH, contact time, agitation rate, and temperature were studied. Adsorption equilibrium was attained after 150 min at pH 6.0 with agitation rate of 400 rpm at 25 °C. The results showed that COD removal percentage of 95.4 and 92.8% for BOD was obtained with carbon dosage of 0.1 g/100 ml of solution. The experimental batch equilibrium results follow linear, Langmuir, and Freundlich isotherm models. The experimental data was fitted to a pseudo-second-order kinetics model controlled by pore diffusion. Thermodynamic parameter values of ΔH 0 , ΔG 0 , and ΔS 0 were calculated. The obtained data indicated that the adsorption was spontaneous, endothermic nature and reflects an increased randomness and degree of disorderliness at the activated carbon/sewage interface during the adsorption process investigated in this study. Concentrations of different impurities were reduced to very small value by investigated adsorption process.

Characteristics and adsorption study of the activated carbon derived from municipal sewage sludge.

PubMed

Guo, Tiecheng; Yao, Sicong; Chen, Hengli; Yu, Xin; Wang, Meicheng; Chen, Yao

2017-10-01

Sewage sludge-based activated carbon is proved to be an efficient and low-cost adsorbent in treatment of various industrial wastewaters. The produced carbon had a well-developed pore structure and relatively low Brunauer-Emmett-Teller (BET) surface area. Adsorptive capacity of typical pollutants, i.e. copper Cu(II) and methylene blue (MB) on the carbon was studied. Adsorptions were affected by the initial solution pH, contact time and adsorbent dose. Results showed that adsorption of Cu(II) and MB on the produced carbon could reach equilibrium after 240 min. The average removal rate for Cu(II) on the carbon was high, up to 97% in weak acidic conditions (pH = 4-6) and around 98% for MB in a very wide pH range (pH = 2-12). The adsorption kinetics were well fitted by the pseudo-second order model, and both Langmuir and Freundlich isotherm models could well describe the adsorption process at room temperature. The theoretical maximum adsorption capacities of Cu(II) and MB on sewage sludge-based activated carbon were 114.94 mg/g and 125 mg/g, respectively. Compared with commercial carbon, the sewage sludge-based carbon was more suitable for heavy metal ions' removal than dyes'.

Sequestration of toxic Pb(II) ions by chemically treated rubber (Hevea brasiliensis) leaf powder.

PubMed

Kamal, Megat Hanafiah Megat Ahmad; Azira, Wan Mat Khalir Wan Khaima; Kasmawati, Mohamed; Haslizaidi, Zakaria; Saime, Wan Ngah Wan

2010-01-01

Rubber leaf powder (an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(II) ions from aqueous solution was evaluated. The interactions between Pb(II) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) coupled with X-ray energy dispersive spectroscopy (EDX). The effects of several important parameters which can affect adsorption capacity such as pH, adsorbent dosage, initial lead concentration and contact time were studied. The optimum pH range for lead adsorption was 4-5. Even at very low adsorbent dosage of 0.02 g, almost 100% of Pb(II) ions (23 mg/L) could be removed. The adsorption capacity was also dependent on lead concentration and contact time, and relatively a short period of time (60-90 min) was required to reach equilibrium. The equilibrium data were analyzed with Langmuir, Freundlich and Dubinin-Radushkevich isotherms. Based on Langmuir model, the maximum adsorption capacity of lead was 95.3 mg/g. Three kinetic models including pseudo first-order, pseudo second-order and Boyd were used to analyze the lead adsorption process, and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.

Enhanced adsorptive removal of Safranine T from aqueous solutions by waste sea buckthorn branch powder modified with dopamine: Kinetics, equilibrium, and thermodynamics

NASA Astrophysics Data System (ADS)

Xu, Xiaohui; Bai, Bo; Wang, Honglun; Suo, Yourui

2015-12-01

Polydopamine coated sea buckthorn branch powder (PDA@SBP) was facilely synthesized via a one-pot bio-inspired dip-coating approach. The as-synthesized PDA@SBP was characterized using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The adsorption progresses of Safranine T on the surface of PDA@SBP adsorbent were systematically investigated. More specifically, the effects of solution pH, contact time, initial concentration and temperature were evaluated, respectively. The experimental results showed the adsorption capacity of PDA@SBP at 293.15 K could reach up to 54.0 mg/g; the adsorption increased by 201.7% compared to that of native SBP (17.9 mg/g). Besides, kinetics studies showed that pseudo-second-order kinetic model adequately described the adsorption behavior. The adsorption experimental data could be fitted well a Freundlich isotherm model. Thermodynamic analyses showed that the ST adsorption was a physisorption endothermic process. Regeneration of the spent PDA@SBP adsorbent was conducted with 0.1 M HCl without significant reduction in adsorption capacity. On the basis of these investigations, it is believed that the PDA@SBP adsorbent could have potential applications in sewage disposal areas because of their considerable adsorption capacities, brilliant regeneration capability, and cost-effective and eco-friendly preparation and use.

Indian jujuba seed powder as an eco-friendly and a low-cost biosorbent for removal of acid blue 25 from aqueous solution.

PubMed

Krishna, L Sivarama; Reddy, A Sreenath; Zuhairi, W Y Wan; Taha, M R; Reddy, A Varada

2014-01-01

Indian jujuba seed powder (IJSP) has been investigated as a low-cost and an eco-friendly biosorbent, prepared for the removal of Acid Blue 25 (AB25) from aqueous solution. The prepared biomaterial was characterized by using FTIR and scanning electron microscopic studies. The effect of operation variables, such as IJSP dosage, contact time, concentration, pH, and temperature on the removal of AB25 was investigated, using batch biosorption technique. Removal efficiency increased with increase of IJSP dosage but decreased with increase of temperature. The equilibrium data were analyzed by the Langmuir and the Freundlich isotherm models. The data fitted well with the Langmuir model with a maximum biosorption capacity of 54.95 mg g(-1). The pseudo-second-order kinetics was the best for the biosorption of AB25 by IJSP, with good correlation. Thermodynamic parameters such as standard free energy change (ΔG(0)), standard enthalpy changes (ΔH(0)), and standard entropy changes (ΔS(0)) were analyzed. The removal of AB25 from aqueous solution by IJSP was a spontaneous and exothermic adsorption process. The results suggest that IJSP is a potential low-cost and an eco-friendly biosorbent for the AB25 removal from synthetic AB25 wastewater.

Equilibrium and kinetic studies of sorption of 2.4-dichlorophenol onto 2 mixtures: bamboo biochar plus calcium sulphate (BC) and hydroxyapatite plus bamboo biochar plus calcium sulphate (HBC), in a fluidized bed circulation column

DOE PAGES

Alamin, Ahmed Hassan; Kaewsichan, Lupong

2016-06-30

Sorption studies were carried out to investigate removal of 2.4-dichlorophenol (2.4-DCP) from aqueous solution in a fluidized bed by two types of adsorbent mixtures: BC (Bamboo char plus Calcium sulphate), and HBC (Hydroxyapatite plus Bamboo char plus Calcium sulphate); both manufactured in ball shape. The main material bamboo char was characterized by FTIR, DTA and SEM. The adsorption experiments were conducted in a fluidized bed circulation column. Adsorption, isotherms and kinetic studies were established under 180 min operating process time, at different initial 2.4-DCP solution concentrations ranging from 5–10 mg/L, and at different flow rates ranging from 0.25–0.75 L/min. Themore » data obtained fitted well for both the Langmuir and Freundlich isotherm models; indicating favorable condition of monolayer adsorption. The kinetics of both adsorbents complies with the pseudo second-order kinetic model. BC was proven a new effective composite and low cost adsorbent which can be applied in the field of wastewater treatment, and it can also play an important role in industry water treatment« less

Adsorption of low concentration ceftazidime from aqueous solutions using impregnated activated carbon promoted by Iron, Copper and Aluminum

NASA Astrophysics Data System (ADS)

Hu, Xiang; Zhang, Hua; Sun, Zhirong

2017-01-01

In this paper, three impregnated activated carbon IAC (AC-Cu, AC-Fe, and AC-Al) promoted by Iron, Copper and Aluminum were used for adsorption of ceftazidime. Iron(III), Copper(II) and Aluminum(III) nitrate were used as an impregnant. The IACs were characterized by scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET) surface area analyzer, Fourier transform infrared spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS).The influence of factors, such as ion strength, pH, temperature, initial concentration, and concentration of natural organic matter organic matter on the adsorption process were studied. The adsorption kinetics and isotherms of ceftazidime were studied for the three IACs. The results showed that the adsorption was accurately represented by pseudo-second order model. Under different temperature, the maximum adsorption quantity of ceftazidime on AC-Cu calculated by pseudo-second order kinetic model were 200.0 mg g-1 (298 K), 196.1 mg g-1 (303 K) and 185.2 mg g-1 (308 K). It was much higher than that of AC-Fe and AC-Al. And the process was controlled by both film diffusion and intra particle mass transport. The results also showed that, the Freundlich and Temkin isotherm fit the adsorption well.

Green synthesis of Fe3O4 nanoparticles loaded sawdust carbon for cadmium (II) removal from water: Regeneration and mechanism.

PubMed

Kataria, Navish; Garg, V K

2018-06-04

This study focused on the synthesis and characterization of novel magnetic iron oxide nanoparticles loaded sawdust carbon (Fe 3 O 4 /SC) and EDTA modified Fe 3 O 4 /SC (EDTA@Fe 3 O 4 /SC) nanocomposites (ncs) by low cost biogenic green synthesis approach and their application for Cd (II) removal from aqueous medium in batch mode. In isotherm studies, Langmuir and Freundlich models are best fitted to Cd (II) removal data. Langmuir maximum adsorption capacity of EDTA@Fe 3 O 4 /SC ncs was found to be 63.3, 22.4 and 25 mg/g that is greater than maximum adsorption capacity of Fe 3 O 4 /SC ncs that is 51, 18.9 and 15 mg/g at the adsorbent doses of 0.4, 1.2 and 2.0 g/L, respectively. Cd (II) adsorption rate is well explained by Pseudo-second order model. Cd (II) adsorption process is spontaneous and endothermic in nature expressed by Enthalpy, Entropy and Free Energy change. The results of regeneration studies showed that EDTA modified Fe 3 O 4 /SC ncs is promising, low cost and eco-friendly for heavy metal adsorption. Copyright © 2018 Elsevier Ltd. All rights reserved.

Adsorption of selected emerging contaminants onto PAC and GAC: Equilibrium isotherms, kinetics, and effect of the water matrix.

PubMed

Real, Francisco J; Benitez, F Javier; Acero, Juan L; Casas, Francisco

2017-07-03

The removal of three emerging contaminants (ECs) (amitriptyline hydrochloride (AH), methyl salicylate (MS) and 2-phenoxyethanol (PE)) dissolved in several water matrices by means of their adsorption onto powdered activated carbon (PAC) and granular activated carbon (GAC) has been investigated. When dissolved in ultrapure water, adsorption of the ECs followed the trend of AH > MS > PE, with a positive effect of the adsorbent dose. According to the analysis of the adsorption isotherms and adsorption kinetics, PAC showed strongly higher adsorption efficiency in both capacity and velocity of the adsorption, in agreement with its higher mesoporosity. Equilibrium isotherm data were fitted by Langmuir and Freundlich models. Pseudo-second order kinetics modeled very successfully the adsorption process. Finally, the effect of the presence of dissolved organic matter (DOM) in the water matrices (ultrapure water, surface water and two effluents from wastewater treatment plants) on the adsorption of the selected ECs onto PAC was established, as well as its performance on the removal of water quality parameters. Results show a negative effect of the DOM content on the adsorption efficiency. Over 50% of organic matter was removed with high PAC doses, revealing that adsorption onto PAC is an effective technology to remove both micro-pollutants and DOM from water matrices.

Adsorption of acids and bases from aqueous solutions onto silicon dioxide particles.

PubMed

Zengin, Huseyin; Erkan, Belgin

2009-12-30

The adsorption of acids and bases onto the surface of silicon dioxide (SiO(2)) particles was systematically studied as a function of several variables, including activation conditions, contact time, specific surface area, particle size, concentration and temperature. The physical properties of SiO(2) particles were investigated, where characterizations were carried out by FT-IR spectroscopy, and morphology was examined by scanning electron microscopy (SEM). The SEM of samples showed good dispersion and uniform SiO(2) particles with an average diameter of about 1-1.5 microm. The adsorption results revealed that SiO(2) surfaces possessed effective interactions with acids and bases, and greatest adsorption capacity was achieved with NaOH, where the best fit isotherm model was the Freundlich adsorption model. The adsorption properties of raw SiO(2) particles were further improved by ultrasonication. Langmuir monolayer adsorption capacity of NaOH adsorbate at 25 degrees C on sonicated SiO(2) (182.6 mg/g) was found to be greater than that of the unsonicated SiO(2) (154.3mg/g). The spontaneity of the adsorption process was established by decreases in DeltaG(ads)(0), which varied from -10.5 to -13.6 kJ mol(-1), in the temperature range 283-338K.

Biogas pre-upgrading by adsorption of trace compounds onto granular activated carbons and an activated carbon fiber-cloth.

PubMed

Boulinguiez, B; Le Cloirec, P

2009-01-01

The study assesses the adsorption onto activated carbon materials of selected volatile organic compounds -VOCs- (dichloromethane, 2-propanol, toluene, siloxane D4) in a biogas matrix composed of methane and carbon dioxide (55:45 v/v). Three different adsorbents are tested, two of them are granular activated carbon (GAC), and the last is an activated carbon fiber-cloth (ACFC). The adsorption isotherm data are fitted by different models by nonlinear regression. The Langmuir-Freundlich model appears to be the adequate one to describe the adsorption phenomena independently of the VOC considered or the adsorbent. The adsorbents present attractive adsorption capacity of the undesirable compounds in biogas atmosphere though the maximum adsorption capacities for a VOC are quite different from each other. The adsorption kinetics are characterized through three coefficients: the initial adsorption coefficient, the external film mass transfer coefficient and the internal diffusion coefficient of Weber. The ACFC demonstrates advanced kinetic yields compared to the granular activated carbon materials whatever VOC is considered. Therefore, pre-upgrading of biogas produced from wastewater sludge or co-digestion system by adsorption onto activated carbon appears worth investigating. Especially with ACFC material that presents correct adsorption capacities toward VOCs and concrete regeneration process opportunity to realize such process.

Magnetically modified sheaths of Leptothrix sp. as an adsorbent for Amido black 10B removal

NASA Astrophysics Data System (ADS)

Angelova, Ralitsa; Baldikova, Eva; Pospiskova, Kristyna; Safarikova, Mirka; Safarik, Ivo

2017-04-01

The goal of this study was to assess the biosorption of Amido black 10B dye from aqueous solutions on magnetically modified sheaths of Leptothrix sp. in a batch system. The magnetic modification of the sheaths was performed using both microwave synthesized iron oxide nano- and microparticles and perchloric acid stabilized ferrofluid. The native and both magnetically modified sheaths were characterized by SEM. Various parameters significantly affecting the adsorption process, such as pH, contact time, temperature and initial concentration, were studied in detail using the adsorbent magnetized by both methods. The highest adsorption efficiency was achieved at pH 2. The maximum adsorption capacities of both types of magnetized material at room temperature were found to be 339.2 and 286.1 mg of dye per 1 g of ferrofluid modified and microwave synthesized particles modified adsorbent, respectively. Thermodynamic study of dye adsorption revealed a spontaneous and endothermic process in the temperature range between 279.15 and 313.15 K. The data were fitted to various equilibrium and kinetic models. Experimental data matched well with the pseudo-second-order kinetics and Freundlich isotherm model. The Leptothrix sheaths have excellent efficacy for dye adsorption. This material can be used as an effective, low-cost adsorbent.

The use of macroalgae (Gracilaria changii) as bio-adsorbent for Copper (II) removal

NASA Astrophysics Data System (ADS)

Lavania-Baloo; Idayu, Nordin; Umar Salihi, Ibrahim; Zainoddin, Jamari

2017-05-01

Biosorption of heavy metals using marine macroalgae biomass can be an effective process and alternative to conventional methods. Activated carbon was developed from macroalgae (Gracilaria changii) and used as adsorbents for the removal of copper (II) from wastewater. Gracilaria changii based activated carbon (GCBAC) was prepared using muffle furnace at a constant temperature of 300 °C for 1 hour. Batch adsorption experiments were conducted to investigate the effets of important parameters such as pH, contact time, initial metal concentration and adsorbent dosage on the removal of Cu (II) from synthetic aqueous solution. Batch adsorption study shows that removal of Cu (II) using GCBAC relied upon pH, contact time, initial metal concentration and GCBAC dosage. The optimum conditions parameters were found to be pH 6.0, time of 60 minutes and GCBAC dosage of 0.3 g, respectively. Adsorption data was described better by Freundlich isotherm model with R2 value of 0.7936. The maximum Cu (II) adsorption capacity of GCBAC was found to be 0.07 mg/g. The experimental adsorption data obtained fitted well into Pseudo-second-order kinetic model, with R2 value near unity. Thus, GCBAC can be used as an effective adsorbent for the removal of Cu (II) from aqueous solution.

Characteristics of uranium biosorption from aqueous solutions on fungus Pleurotus ostreatus.

PubMed

Zhao, Changsong; Liu, Jun; Tu, Hong; Li, Feize; Li, Xiyang; Yang, Jijun; Liao, Jiali; Yang, Yuanyou; Liu, Ning; Sun, Qun

2016-12-01

Uranium(VI) biosorption from aqueous solutions was investigated in batch studies by using fungus Pleurotus ostreatus biomass. The optimal biosorption conditions were examined by investigating the reaction time, biomass dosage, pH, temperature, and uranium initial concentration. The interaction between fungus biomass and uranium was confirmed using Fourier transformed infrared (FT-IR), scanning electronic microscopy energy dispersive X-ray (SEM-EDX), and X-ray photoelectron spectroscopy (XPS) analysis. Results exhibited that the maximum biosorption capacity of uranium on P. ostreatus was 19.95 ± 1.17 mg/g at pH 4.0. Carboxylic, amine, as well as hydroxyl groups were involved in uranium biosorption according to FT-IR analysis. The pseudo-second-order model properly evaluated the U(VI) biosorption on fungus P. ostreatus biomass. The Langmuir equation provided better fitting in comparison with Freundlich isotherm models. The obtained thermodynamic parameters suggested that biosorption is feasible, endothermic, and spontaneous. SEM-EDX and XPS were additionally conducted to comprehend the biosorption process that could be described as a complex process involving several mechanisms of physical adsorption, chemisorptions, and ion exchange. Results obtained from this work indicated that fungus P. ostreatus biomass can be used as potential biosorbent to eliminate uranium or other radionuclides from aqueous solutions.

Lead-binding capacity of calcium pectates with different molecular weight.

PubMed

Khotimchenko, Maksim; Makarova, Ksenia; Khozhaenko, Elena; Kovalev, Valeri

2017-04-01

Nowadays, heavy metal contamination of environment is considered as a serious threat to public health because of toxicity of these pollutants and the lack of effective materials with metal-binding properties. Some biopolymers such as pectins were proposed for removal of metal ions from industrial water disposals. Chemical structure of pectins is quite variable and substantially affects their metal binding properties. In this work, relationship between molecular weight and Pb(II)-binding capacity of calcium pectates was investigated in a batch sorption system. The results showed that all pectate samples are able to form complexes with Pb(II) ions. The effects of contact time, pH of the media and equilibrium metal concentration on metal-binding process were tested in experiments. The equilibrium time min required for uptake of Pb(II) by pectate compounds was found to be 60min. Langmuir and Freundlich models were applied for description of interactions between pectates and metal ions. Binding capacity of low molecular pectate was highest among all the samples tested. Langmuir model was figured out to be the best fit within the whole range of pH values. These results demonstrate that calcium pectate with low molecular weight is more promising agent for elimination of Pb(II) ions from contaminated wastewaters. Copyright © 2017 Elsevier B.V. All rights reserved.

Ultrasonic-assisted synthesis of novel nanocomposite of poly(vinyl alcohol) and amino-modified MCM-41: A green adsorbent for Cd(II) removal.

PubMed

Soltani, Roozbeh; Dinari, Mohammad; Mohammadnezhad, Gholamhossein

2018-01-01

Amino-modified MCM-41/poly(vinyl alcohol) nanocomposite (M-MCM-41/PVOH NC) was developed for the adsorption of Cd(II) from aqueous media. M-MCM-41/PVOH NC was prepared through ultrasonic-assisted and simple blending procedure with economical and environmentally friendly polymer. The as-prepared adsorbent was characterized by FT-IR, TEM, FE-SEM and TGA. The contact time, solution pH and initial concentration of Cd(II) were found to affect the adsorption of Cd(II) from aqueous media. Kinetic studies were carried out and pseudo-first-order (PFO), pseudo-second-order (PSO), Elovich, and intra-particle diffusion (IPD) reaction kinetic models were examined. The kinetic results revealed that the adsorption of Cd(II) onto M-MCM-41/PVOH NC followed PSO kinetic model and is a chemical adsorption. The equilibrium adsorption data were evaluated by different isotherms viz. Langmuir, Freundlich, and Dubinin Radushkevich (D-R) equations. The equilibrium data fitted better with the Langmuir isotherm and the maximum adsorption capacity of M-MCM-41/PVOH NC at 298K was calculated to be 46.73mgg -1 for Cd(II) on a typical saturated monomolecular layer with a fixed number of localized adsorption sites. Copyright © 2017 Elsevier B.V. All rights reserved.

Equilibrium and kinetic studies of sorption of 2.4-dichlorophenol onto 2 mixtures: bamboo biochar plus calcium sulphate (BC) and hydroxyapatite plus bamboo biochar plus calcium sulphate (HBC), in a fluidized bed circulation column

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alamin, Ahmed Hassan; Kaewsichan, Lupong

Sorption studies were carried out to investigate removal of 2.4-dichlorophenol (2.4-DCP) from aqueous solution in a fluidized bed by two types of adsorbent mixtures: BC (Bamboo char plus Calcium sulphate), and HBC (Hydroxyapatite plus Bamboo char plus Calcium sulphate); both manufactured in ball shape. The main material bamboo char was characterized by FTIR, DTA and SEM. The adsorption experiments were conducted in a fluidized bed circulation column. Adsorption, isotherms and kinetic studies were established under 180 min operating process time, at different initial 2.4-DCP solution concentrations ranging from 5–10 mg/L, and at different flow rates ranging from 0.25–0.75 L/min. Themore » data obtained fitted well for both the Langmuir and Freundlich isotherm models; indicating favorable condition of monolayer adsorption. The kinetics of both adsorbents complies with the pseudo second-order kinetic model. BC was proven a new effective composite and low cost adsorbent which can be applied in the field of wastewater treatment, and it can also play an important role in industry water treatment« less

Removal of ammonium and heavy metals by cost-effective zeolite synthesized from waste quartz sand and calcium fluoride sludge.

PubMed

Zhang, Qian; Lin, Bing; Hong, Junming; Chang, Chang-Tang

2017-02-01

This study focuses on the effectiveness of zeolite (10% CF-Z [0.5]) hydrothermally synthesized from waste quartz sand and calcium fluoride (CF) for ammonium ion and heavy metal removal. Zeolite was characterized through powder X-ray diffraction, Fourier-transform infrared spectroscopy, micromeritics N 2 adsorption/desorption analysis, and field emission scanning electron microscopy. The effects of CF addition, Si/Al ratio, initial ammonium concentration, solution pH, and temperature on the adsorption of ammonium on 10% CF-Z (0.5) were further examined. Results showed that 10% CF-Z (0.5) was a single-phase zeolite A with cubic-shaped crystals and 10% CF-Z (0.5) efficiently adsorbs ammonium and heavy metals. For instance, 91% ammonium (10 mg L -1 ) and 93% lead (10 mg L -1 ) are removed. The adsorption isotherm, kinetics, and thermodynamics of ammonium adsorption on 10% CF-Z (0.5) were also theoretically analyzed. The adsorption isotherm of ammonium and lead on 10% CF-Z (0.5) in single systems indicated that Freundlich model provides the best fit for the equilibrium data, whereas pseudo-second-order model best describes the adsorption kinetics. The adsorption degree of ions on 10% CF-Z (0.5) in mixed systems exhibits the following pattern: lead > ammonium > cadmium > chromium.

Enhanced fluoride removal by La-doped Li/Al layered double hydroxides.

PubMed

Cai, Jianguo; Zhao, Xin; Zhang, Yanyang; Zhang, Quanxing; Pan, Bingcai

2018-01-01

In this study La intercalated Li/Al layered double hydroxide (LDH) was developed for efficient water defluoridation. The La-modified material, i.e., La doped Li/Al-LDH, exhibits more preferable fluoride adsorption than Li/Al-LDH in a broad pH range of 5-9, with the working capacity twice of the latter and seven times of magnitude higher than activated alumina. The fluoride removal kinetics is well fitted by pseudo-second order model, and the adsorption isotherm is well described by Freundlich model. Effect of pH and competing ions was examined during fluoride sequestration. The underlying mechanism for such enhanced adsorption of fluoride by La doped Li/Al-LDH was further revealed based on XPS and FTIR analysis. The presence of La and Al was found to be responsible for the satisfactory defluoridation of La doped Li/Al-LDH, and chloride replacement with fluoride occurred from both LDHs during fluoride adsorption. Also, the capacity of La doped Li/Al-LDH could be refreshed by alkaline solution (pH = 12) for cyclic runs. All the results implied that La doped Li/Al-LDH could serve asa potential adsorbent for efficient fluoride removal from water. Copyright © 2017 Elsevier Inc. All rights reserved.

Indian Jujuba Seed Powder as an Eco-Friendly and a Low-Cost Biosorbent for Removal of Acid Blue 25 from Aqueous Solution

PubMed Central

Krishna, L. Sivarama; Reddy, A. Sreenath; Zuhairi, W. Y. Wan; Taha, M. R.; Reddy, A. Varada

2014-01-01

Indian jujuba seed powder (IJSP) has been investigated as a low-cost and an eco-friendly biosorbent, prepared for the removal of Acid Blue 25 (AB25) from aqueous solution. The prepared biomaterial was characterized by using FTIR and scanning electron microscopic studies. The effect of operation variables, such as IJSP dosage, contact time, concentration, pH, and temperature on the removal of AB25 was investigated, using batch biosorption technique. Removal efficiency increased with increase of IJSP dosage but decreased with increase of temperature. The equilibrium data were analyzed by the Langmuir and the Freundlich isotherm models. The data fitted well with the Langmuir model with a maximum biosorption capacity of 54.95 mg g−1. The pseudo-second-order kinetics was the best for the biosorption of AB25 by IJSP, with good correlation. Thermodynamic parameters such as standard free energy change (ΔG 0), standard enthalpy changes (ΔH 0), and standard entropy changes (ΔS 0) were analyzed. The removal of AB25 from aqueous solution by IJSP was a spontaneous and exothermic adsorption process. The results suggest that IJSP is a potential low-cost and an eco-friendly biosorbent for the AB25 removal from synthetic AB25 wastewater. PMID:25383360

Ammonium removal from high-strength aqueous solutions by Australian zeolite.

PubMed

Wijesinghe, D Thushari N; Dassanayake, Kithsiri B; Sommer, Sven G; Jayasinghe, Guttila Y; J Scales, Peter; Chen, Deli

2016-07-02

Removal of ammonium nitrogen (NH4(+)-N) particularly from sources which are highly rich in nitrogen is important for addressing environmental pollution. Zeolites, aluminosilicate minerals, are commonly used as commercial adsorbents and ion-exchange medium in number of commercial applications due to its high adsorption capacity of ammonium (NH4(+)). However, detailed investigations on NH4(+) adsorption and ion exchange capacities of Australian natural zeolites are rare, particularly under higher NH4(+) concentrations in the medium. Therefore, this study was conducted to determine NH4(+) adsorption characteristics of Australian natural zeolites at high NH4(+) concentrations with and without other chemical compounds in an aqueous solution. Results showed that initial NH4(+) concentration, temperature, reaction time, and pH of the solution had significant effects on NH4(+) adsorption capacity of zeolite. Increased retention time and temperature generally had a positive impact on adsorption. Freundlich model fitted well with adsorption process of Australian natural zeolites; however, Langmuir model had best fitted for the adsorption process of sodium (Na(+)) treated zeolites. NaCl treatment increased the NH4(+) adsorption capacity of Australian zeolites by 25% at 1000 mg-N, NH4(+) solution. The maximum adsorption capacity of both natural Australian zeolites and Na(+) treated zeolites were estimated as 9.48 and 11.83 mg-N/g, respectively, which is lower than many zeolites from other sources. Compared to the NH4(+) only medium, presence of other competitive ions and acetic acid in the medium (resembling composition in digested swine manure slurries) reduced NH4(+) removal of natural and Na(+) treated zeolites by 44% and 57%, respectively. This suggests detailed investigations are required to determine practically achievable NH4(+) -N removal potential of zeolites for applications in complex mediums such as animal manure slurries.

Competitive removal of hazardous dyes from aqueous solution by MIL-68(Al): Derivative spectrophotometric method and response surface methodology approach

NASA Astrophysics Data System (ADS)

Tehrani, Mahnaz Saghanejhad; Zare-Dorabei, Rouholah

2016-05-01

MIL-68(Al) as a metal-organic framework (MOF) was synthesized and characterized by different techniques such as SEM, BET, FTIR, and XRD analysis. This material was then applied for simulations removal of malachite green (MG) and methylene blue (MB) dyes from aqueous solutions using second order derivative spectrophotometric method (SODS) which was applied to resolve the overlap between the spectra of these dyes. The dependency of dyes removal efficiency in binary solutions was examined and optimized toward various parameters including initial dye concentration, pH of the solution, adsorbent dosage and ultrasonic contact time using central composite design (CCD) under response surface methodology (RSM) approach. The optimized experimental conditions were set as pH 7.78, contact time 5 min, initial MB concentration 22 mg L- 1, initial MG concentration 12 mg L- 1 and adsorbent dosage 0.0055 g. The equilibrium data was fitted to isotherm models such as Langmuir, Freundlich and Tempkin and the results revealed the suitability of the Langmuir model. The maximum adsorption capacity of 666.67 and 153.85 mg g- 1 was obtained for MB and MG removal respectively. Kinetics data fitting to pseudo-first order, pseudo-second order and Elovich models confirmed the applicability of pseudo-second order kinetic model for description of the mechanism and adsorption rate. Dye-loaded MIL-68(Al) can be easily regenerated using methanol and applied for three frequent sorption/desorption cycles with high performance. The impact of ionic strength on removal percentage of both dyes in binary mixture was studied by using NaCl and KCl soluble salts at different concentrations. According to our findings, only small dosage of the proposed MOF is considerably capable to remove large amounts of dyes at room temperature and in very short time that is a big advantage of MIL-68(Al) as a promising adsorbent for adsorptive removal processes.

Simultaneous ultrasound-assisted ternary adsorption of dyes onto copper-doped zinc sulfide nanoparticles loaded on activated carbon: optimization by response surface methodology.

PubMed

Asfaram, Arash; Ghaedi, Mehrorang; Hajati, Shaaker; Goudarzi, Alireza; Bazrafshan, Ali Akbar

2015-06-15

The simultaneous and competitive ultrasound-assisted removal of Auramine-O (AO), Erythrosine (Er) and Methylene Blue (MB) from aqueous solutions were rapidly performed onto copper-doped zinc sulfide nanoparticles loaded on activated carbon (ZnS:Cu-NP-AC). ZnS:Cu nanoparticles were studied by FESEM, XRD and TEM. First, the effect of pH was optimized in a one-at-a-time procedure. Then the dependency of dyes removal percentage in their ternary solution on the level and magnitude of variables such as sonication time, initial dyes concentrations and adsorbent dosage was fully investigated and optimized by central composite design (CCD) under response surface methodology (RSM) as well as by regarding desirability function (DF) as a good and general criterion. The good agreement found between experimental and predicted values supports and confirms the suitability of the present model to predict adsorption state. The applied ultrasound strongly enhanced mass transfer process and subsequently performance. Hence, a small amount of the adsorbent (0.04 g) was capable to remove high percentage of dyes, i.e. 100%, 99.6% and 100% for MB, AO and Er, respectively, in very short time (2.5 min). The experimental equilibrium data fitting to Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models showed that the Langmuir model applies well for the evaluation and description of the actual behavior of adsorption. The small amount of proposed adsorbent (0.015 g) was applicable for successful removal of dyes (RE>99.0%) in short time (2.5 min) with high adsorption capacity in single component system (123.5 mg g(-1) for MB, 123 mg g(-1) for AO and 84.5 mg g(-1) for Er). Kinetics evaluation of experiments at various time intervals reveals that adsorption processes can be well predicated and fitted by pseudo-second-order and Elovich models. Copyright © 2015 Elsevier B.V. All rights reserved.

Adsorptive potential of cationic Basic Yellow 2 (BY2) dye onto natural untreated clay (NUC) from aqueous phase: Mass transfer analysis, kinetic and equilibrium profile

NASA Astrophysics Data System (ADS)

Öztürk, A.; Malkoc, E.

2014-04-01

In this work, natural untreated clay (NUC) was studied for the removal of Basic Yellow 2 (BY2) from aqueous solution in batch system. The effects of initial BY2 concentration, contact time, solution temperature and solution pH on BY2 adsorption were investigated. Nitrogen sorption measurements were employed to investigate the variation in surface and pore properties after dye adsorption. The adsorbent was characterized by means of FTIR, PSD, TEM, XRD and BET analysis. The equilibrium adsorption data were analyzed by Langmuir, Freundlich, Temkin and Scatchard isotherm models. The maximum monolayer adsorption capacity was found to be 833.33 mg/g at 25 °C (at room temperature). The pseudo-second-order kinetic model provided the best fit to the experimental datas compared with pseudo-first-order kinetic adsorption models. To explain mass transfer mechanism of BY2 adsorption, obtained experimental datas were applied Weber and Morris model, Body and Frusawa and Smith models. The results show that the adsorption process is controlled by film diffusion. The thermodynamic parameters such as, Gibbs free energy changes (ΔG°), standard enthalpy change (ΔH°) and standard entropy change (ΔS°) were determined. Adsorption of BY2 on NUC is exothermic and spontaneous in nature. The calculated activation energy of adsorption was found to be 5.24 kJ/mol for BY2. This value indicates that the adsorption process is a physisorption.

Activated carbon from pyrolysis of brewer's spent grain: Production and adsorption properties.

PubMed

Vanreppelen, Kenny; Vanderheyden, Sara; Kuppens, Tom; Schreurs, Sonja; Yperman, Jan; Carleer, Robert

2014-07-01

Brewer's spent grain is a low cost residue generated by the brewing industry. Its chemical composition (high nitrogen content 4.35 wt.%, fibres, etc.) makes it very useful for the production of added value in situ nitrogenised activated carbon. The composition of brewer's spent grain revealed high amounts of cellulose (20.8 wt.%), hemicellulose (48.78 wt.%) and lignin (11.3 wt.%). The fat, ethanol extractives and ash accounted for 8.17 wt.%, 4.7 wt.% and 3.2 wt.%, respectively. Different activated carbons were produced in a lab-scale pyrolysis/activation reactor by applying several heat and steam activation profiles on brewer's spent grain. Activated carbon yields from 16.1 to 23.6 wt.% with high N-contents (> 2 wt.%) were obtained. The efficiency of the prepared activated carbons for phenol adsorption was studied as a function of different parameters: pH, contact time and carbon dosage relative to two commercial activated carbons. The equilibrium isotherms were described by the non-linear Langmuir and Freundlich models, and the kinetic results were fitted using the pseudo-first-order model and the pseudo-second-order model. The feasibility of an activated carbon production facility (onsite and offsite) that processes brewer's spent grain for different input feeds is evaluated based on a techno-economic model for estimating the net present value. Even though the model assumptions start from a rather pessimistic scenario, encouraging results for a profitable production of activated carbon using brewer's spent grain are obtained. © The Author(s) 2014.

Mercerized mesoporous date pit activated carbon—A novel adsorbent to sequester potentially toxic divalent heavy metals from water

PubMed Central

Aldawsari, Abdullah; Hameed, B. H.; Alqadami, Ayoub Abdullah; Siddiqui, Masoom Raza; Alothman, Zeid Abdullah; Ahmed, A. Yacine Badjah Hadj

2017-01-01

A substantive approach converting waste date pits to mercerized mesoporous date pit activated carbon (DPAC) and utilizing it in the removal of Cd(II), Cu(II), Pb(II), and Zn(II) was reported. In general, rapid heavy metals adsorption kinetics for Co range: 25–100 mg/L was observed, accomplishing 77–97% adsorption within 15 min, finally, attaining equilibrium in 360 min. Linear and non-linear isotherm studies revealed Langmuir model applicability for Cd(II) and Pb(II) adsorption, while Freundlich model was fitted to Zn(II) and Cu(II) adsorption. Maximum monolayer adsorption capacities (qm) for Cd(II), Pb(II), Cu(II), and Zn(II) obtained by non-linear isotherm model at 298 K were 212.1, 133.5, 194.4, and 111 mg/g, respectively. Kinetics modeling parameters showed the applicability of pseudo-second-order model. The activation energy (Ea) magnitude revealed physical nature of adsorption. Maximum elution of Cu(II) (81.6%), Zn(II) (70.1%), Pb(II) (96%), and Cd(II) (78.2%) were observed with 0.1 M HCl. Thermogravimetric analysis of DPAC showed a total weight loss (in two-stages) of 28.3%. Infra-red spectral analysis showed the presence of carboxyl and hydroxyl groups over DPAC surface. The peaks at 820, 825, 845 and 885 cm-1 attributed to Zn–O, Pb–O, Cd–O, and Cu–O appeared on heavy metals saturated DPAC, confirmed their binding on DPAC during the adsorption. PMID:28910368

Efficacy of mangrove leaf powder for bioremediation of chromium (VI) from aqueous solutions: kinetic and thermodynamic evaluation

NASA Astrophysics Data System (ADS)

Sathish, Thadikamala; Vinithkumar, N. V.; Dharani, G.; Kirubagaran, R.

2015-06-01

Biosorption of heavy metals by bio-materials has been posited as a potential alternative to the existing physicochemical technologies for detoxification and recovery of toxic and valuable metals from wastewaters. In this context, the role of mangrove leaf powder (MLP) as biosorbent for chromium removal was investigated. In the present study, the effect of process parameters such as particle size, solution pH, initial concentration of Cr(VI) ion and adsorbent dose on chromium removal by MLP was investigated. The maximum sorption was observed at particle size 0.5 mm and pH 2.0. The adsorption data follow the pseudo second-order kinetics model. The isotherms denote that Langmuir model is the best fitted than Freundlich model. The maximum adsorption capacity ( Q 0) of 60.24 mg/g of Cr(VI) at 30 min on MLP was determined using the Langmuir model. The adsorption isotherm model indicates that the chromium is adsorbing as monolayer on the surface of MLP with heterogeneous energetic distribution of active sites. Various thermodynamic parameters, such as Gibb's free energy (∆ G °), enthalpy (∆ H °) and entropy (∆ S °) have been calculated. The thermodynamic data revealed that the adsorption of chromium ions onto MLP is endothermic in nature and a spontaneous process. The results of the present study suggest that MLP is an effective bioremediation measure for removal of high concentration of Cr(VI) in waste waters.

Mercerized mesoporous date pit activated carbon-A novel adsorbent to sequester potentially toxic divalent heavy metals from water.

PubMed

Aldawsari, Abdullah; Khan, Moonis Ali; Hameed, B H; Alqadami, Ayoub Abdullah; Siddiqui, Masoom Raza; Alothman, Zeid Abdullah; Ahmed, A Yacine Badjah Hadj

2017-01-01

A substantive approach converting waste date pits to mercerized mesoporous date pit activated carbon (DPAC) and utilizing it in the removal of Cd(II), Cu(II), Pb(II), and Zn(II) was reported. In general, rapid heavy metals adsorption kinetics for Co range: 25-100 mg/L was observed, accomplishing 77-97% adsorption within 15 min, finally, attaining equilibrium in 360 min. Linear and non-linear isotherm studies revealed Langmuir model applicability for Cd(II) and Pb(II) adsorption, while Freundlich model was fitted to Zn(II) and Cu(II) adsorption. Maximum monolayer adsorption capacities (qm) for Cd(II), Pb(II), Cu(II), and Zn(II) obtained by non-linear isotherm model at 298 K were 212.1, 133.5, 194.4, and 111 mg/g, respectively. Kinetics modeling parameters showed the applicability of pseudo-second-order model. The activation energy (Ea) magnitude revealed physical nature of adsorption. Maximum elution of Cu(II) (81.6%), Zn(II) (70.1%), Pb(II) (96%), and Cd(II) (78.2%) were observed with 0.1 M HCl. Thermogravimetric analysis of DPAC showed a total weight loss (in two-stages) of 28.3%. Infra-red spectral analysis showed the presence of carboxyl and hydroxyl groups over DPAC surface. The peaks at 820, 825, 845 and 885 cm-1 attributed to Zn-O, Pb-O, Cd-O, and Cu-O appeared on heavy metals saturated DPAC, confirmed their binding on DPAC during the adsorption.

Adsorption of pharmaceuticals onto activated carbon fiber cloths - Modeling and extrapolation of adsorption isotherms at very low concentrations.

PubMed

Fallou, Hélène; Cimetière, Nicolas; Giraudet, Sylvain; Wolbert, Dominique; Le Cloirec, Pierre

2016-01-15

Activated carbon fiber cloths (ACFC) have shown promising results when applied to water treatment, especially for removing organic micropollutants such as pharmaceutical compounds. Nevertheless, further investigations are required, especially considering trace concentrations, which are found in current water treatment. Until now, most studies have been carried out at relatively high concentrations (mg L(-1)), since the experimental and analytical methodologies are more difficult and more expensive when dealing with lower concentrations (ng L(-1)). Therefore, the objective of this study was to validate an extrapolation procedure from high to low concentrations, for four compounds (Carbamazepine, Diclofenac, Caffeine and Acetaminophen). For this purpose, the reliability of the usual adsorption isotherm models, when extrapolated from high (mg L(-1)) to low concentrations (ng L(-1)), was assessed as well as the influence of numerous error functions. Some isotherm models (Freundlich, Toth) and error functions (RSS, ARE) show weaknesses to be used as an adsorption isotherms at low concentrations. However, from these results, the pairing of the Langmuir-Freundlich isotherm model with Marquardt's percent standard of deviation was evidenced as the best combination model, enabling the extrapolation of adsorption capacities by orders of magnitude. Copyright © 2015 Elsevier Ltd. All rights reserved.

Transport models for desorption from natural soils packed in flushed columns

NASA Astrophysics Data System (ADS)

Brouwers, H. J. H.

1999-06-01

This paper addresses an experimental and theoretical study of sorbed contaminant removal from a column (or reactor) by flushing. This removal may take place by either volatilization or rinsing, and nonlinear sorption is accounted for by employing a Freundlich relationship. A one-dimensional nonequilibrium transport model is proposed which describes the unsteady mass transfer between flushing medium and soil phases in the column, using a linear chemical transfer model. The moving boundary problem is transferred, and a perturbation method is employed to obtain an approximate solution of the governing equations for a small Merkel number Me (this dimensionless number comprises the product of fluid residence time and the mass transfer coefficient). The solution reveals the effect of the various parameters, such as the Freundlich parameter n, on the contaminant transport in fluid phase and decay in solid phase. Applying the model to various experimental data results in values for the overall mass transfer coefficients, which are useful for engineering computations. Furthermore, the model enables the prediction of the initial soil contamination level as well as the parameter n solely from the measured exit contaminant concentrations in the flushing fluid. A thorough comparison of this prediction with the measured soil concentration (prior to the experiments) yields good agreement.

Derivation of the Freundlich Adsorption Isotherm from Kinetics

ERIC Educational Resources Information Center

Skopp, Joseph

2009-01-01

The Freundlich adsorption isotherm is a useful description of adsorption phenomena. It is frequently presented as an empirical equation with little theoretical basis. In fact, a variety of derivations exist. Here a new derivation is presented using the concepts of fractal reaction kinetics. This derivation provides an alternative basis for…

In Vitro and In Vivo Evaluation of Lactobacillus delbrueckii subsp. bulgaricus KLDS1.0207 for the Alleviative Effect on Lead Toxicity

PubMed Central

Li, Bailiang; Jin, Da; Yu, Shangfu; Etareri Evivie, Smith; Muhammad, Zafarullah; Huo, Guicheng; Liu, Fei

2017-01-01

Lead (Pb) is a toxic contaminating heavy metal that can cause a variety of hazardous effects to both humans and animals. In the present study, Lactobacillus delbrueckii subsp. bulgaricus KLDS1.0207 (L. bulgaricus KLDS1.0207), which has a remarkable Pb binding capacity and Pb tolerance, was selected for further study. It was observed that the thermodynamic and kinetic model of L. bulgaricus KLDS1.0207 Pb binding respectively fit with the Langmuir–Freundlich model and the pseudo second-order kinetic model. Scanning electron microscopy and energy dispersive spectroscopy analysis disclosed that the cell surfaces were covered with Pb and that carbon and oxygen elements were chiefly involved in Pb binding. Combined with Fourier transform infrared spectroscopy analysis, it was revealed that the carboxyl, phosphoryl, hydroxyl, amino and amide groups were the main functional groups involved in the Pb adsorption. The protective effects of L. bulgaricus KLDS1.0207 against acute Pb toxicity in mice was evaluated by prevention and therapy groups, the results in vivo showed that L. bulgaricus KLDS1.0207 treatment could reduce mortality rates, effectively increase Pb levels in the feces, alleviate tissue Pb enrichment, improve the antioxidant index in the liver and kidney, and relieve renal pathological damage. Our findings show that L. bulgaricus KLDS1.0207 can be used as a potential probiotic against acute Pb toxicity. PMID:28786945

Iron and manganese oxides modified maize straw to remove tylosin from aqueous solutions.

PubMed

Yin, Yongyuan; Guo, Xuetao; Peng, Dan

2018-08-01

Maize straw modified by iron and manganese oxides was synthesized via a simple and environmentally friendly method. Three maize straw materials, the original maize straw, maize straw modified by manganese oxides and maize straw modified by iron and manganese oxides, were detected by SEM, BET, XPS, XRD and FTIR. The results showed that maize straw was successfully modified and maize straw modified by iron and manganese oxides has a larger surface area than MS. According to the experimental data, the sorption trend could conform to the pseudo-second-order kinetic model well, and the sorption ability of tylosin on sorbents followed the order of original maize straw < maize straw modified by manganese oxides < maize straw modified by iron and manganese oxides. The study indicated that manganese oxides and iron-manganese oxides could significantly enhance the sorption capacity of original maize straw. The sorption isotherm data of tylosin on original maize straw fit a linear model well, while Freundlich models were more suitable for maize straw modified by manganese oxides and maize straw modified by iron and manganese oxides. The pH, ionic strength and temperature can affect the sorption process. The sorption mechanisms of tylosin on iron and manganese oxides modified maize straw were attribute to the surface complexes, electrostatic interactions, H bonding and hydrophobic interactions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ethylenediamine grafted to graphene oxide@Fe3O4 for chromium(VI) decontamination: Performance, modelling, and fractional factorial design

PubMed Central

Xu, Jiawen; Wu, Cuiyu; Deng, Jianbin; Liao, Wenwei; Ling, Yuxiang; Yang, Yuanxiu; Zhao, Yina; Zhao, Yunlin; Hu, Xi; Wang, Hui; Liu, Yunguo

2017-01-01

A method for grafting ethylenediamine to a magnetic graphene oxide composite (EDA-GO@Fe3O4) was developed for Cr(VI) decontamination. The physicochemical properties of EDA-GO@Fe3O4 were characterized using HRTEM, EDS, FT-IR, TG-DSC, and XPS. The effects of pH, sorbent dose, foreign anions, time, Cr(VI) concentration, and temperature on decontamination process were studied. The solution pH can largely affect the decontamination process. The pseudo-second-order model is suitable for being applied to fit the adsorption processes of Cr(VI) with GO@Fe3O4 and EDA-GO@Fe3O4. The intra-particle diffusion is not the rate-controlling step. Isotherm experimental data can be described using the Freundlich model. The effects of multiple factors on the Cr(VI) decontamination was investigated by a 25−1 fractional factorial design (FFD). The adsorption process can significantly be affected by the main effects of A (pH), B (Cr(VI) concentration), and E (Adsorbent dose). The combined factors of AB (pH × Cr(VI) concentration), AE (pH × Adsorbent dose), and BC (Cr(VI) concentration × Temperature) had larger effects than other factors on Cr(VI) removal. These results indicated that EDA-GO@Fe3O4 is a potential and suitable candidate for treatment of heavy metal wastewater. PMID:29084287

Application of acidic treated pumice as an adsorbent for the removal of azo dye from aqueous solutions: kinetic, equilibrium and thermodynamic studies

PubMed Central

2012-01-01

Colored effluents are one of the important environment pollution sources since they contain unused dye compounds which are toxic and less-biodegradable. In this work removal of Acid Red 14 and Acid Red 18 azo dyes was investigated by acidic treated pumice stone as an efficient adsorbent at various experimental conditions. Removal of dye increased with increase in contact time and initial dye concentration, while decreased for increment in solution temperature and pH. Results of the equilibrium study showed that the removal of AR14 and AR18 followed Freundlich (r2>0.99) and Langmuir (r2>0.99) isotherm models. Maximum sorption capacities were 3.1 and 29.7 mg/g for AR 14 and AR18, namely significantly higher than those reported in the literature, even for activated carbon. Fitting of experimental data onto kinetic models showed the relevance of the pseudo-second order (r2>0.99) and intra-particle diffusion (r2>0.98) models for AR14 and AR18, respectively. For both dyes, the values of external mass transfer coefficient decreased for increasing initial dye concentrations, showing increasing external mass transfer resistance at solid/liquid layer. Desorption experiments confirmed the relevance of pumice stone for dye removal, since the pH regeneration method showed 86% and 89% regeneration for AR14 and AR18, respectively. PMID:23369579

Copper (II) adsorption by the extracellular polymeric substance extracted from waste activated sludge after short-time aerobic digestion.

PubMed

Zhang, Zhiqiang; Zhou, Yun; Zhang, Jiao; Xia, Siqing

2014-02-01

The extracellular polymeric substance (EPS) extracted from waste activated sludge (WAS) after short-time aerobic digestion was investigated to be used as a novel biosorbent for Cu(2+) removal from water. The EPS consisted of protein (52.6 %, w/w), polysaccharide (30.7 %, w/w), and nucleic acid (16.7 %, w/w). Short-time aerobic digestion process of WAS for about 4 h promoted the productivity growth of the EPS for about 10 %. With a molecular weight of about 1.9 × 10(6) Da, the EPS showed a linear structure with long chains, and contained carboxyl, hydroxyl, and amino groups. The sorption kinetics was well fit for the pseudo-second-order model, and the maximum sorption capacity of the EPS (700.3 mg Cu(2+)/g EPS) was markedly greater than those of the reported biosorbents. Both Langmuir model and Freundlich model commendably described the sorption isotherm. The Gibbs free energy analysis of the adsorption showed that the sorption process was feasible and spontaneous. According to the complex results of multiple analytical techniques, including scanning electron microscopy, Fourier transform infrared spectroscopy, atomic force microscopy, etc., the adsorption process took place via both physical and chemical sorption, but the electrostatic interaction between sorption sites with the functional groups and Cu(2+) is the major mechanism.

3D hierarchical flower-like nickel ferrite/manganese dioxide toward lead (II) removal from aqueous water.

PubMed

Xiang, Bo; Ling, Dong; Lou, Han; Gu, Hongbo

2017-03-05

A functionalized magnetic nickel ferrite/manganese dioxide (NiFe 2 O 4 /MnO 2 ) with 3D hierarchical flower-like and core-shell structure was synthesized by a facile hydrothermal approach and applied for the removal of Pb(II) ions from aqueous solutions. Batch adsorption experiments were conducted to study the effect of solution pH, initial Pb(II) concentration, and dose of absorbents on the Pb(II) removal by NiFe 2 O 4 /MnO 2 . The NiFe 2 O 4 /MnO 2 nanocomposites showed the fast Pb(II) adsorption performance with the maximum adsorption capacity of 85.78mgg -1 . The adsorption kinetics of Pb(II) onto NiFe 2 O 4 /MnO 2 obeyed a pseudo-second-order model. The isothermal experimental results indicated that the Langmuir model was fitted better than the Freundlich model, illustrating a monolayer adsorption process for Pb(II) onto NiFe 2 O 4 /MnO 2 . Meanwhile, the NiFe 2 O 4 /MnO 2 was easily separated from the solution by an external magnet within a short period of time and still exhibited almost 80% removal capacity after six regenerations. The NiFe 2 O 4 /MnO 2 is expected to be a new promising adsorbent for heavy metal removal. Copyright © 2016 Elsevier B.V. All rights reserved.

Synthesis, characterization and trivalent arsenic sorption potential of Ce-Al nanostructured mixed oxide

NASA Astrophysics Data System (ADS)

Bhattacharya, S.; Gupta, K.; Ghosh, U. C.

2017-04-01

Arsenic contamination in the ground water has serious health consequences in many parts of the world. The surface sorption method for arsenic mitigation has been widely investigated due to its simple method, inexpensive operation, highly efficient and low content of by-products. In the present study, nanostructured hydrated cerium aluminum oxide (NHCAO) was synthesized and characterized and its arsenic (III) sorption behavior from the aqueous solution was studied. The material was characterized in SEM, FE-SEM, TEM, AFM, XRD, and FT-IR. Batch method was used for the kinetics of As (III) sorption on nanoparticles at 303 (± 1.6) K and at pH 7.0 (± 0.2). The experiments on isotherm subject were performed individually at 288K, 303K, 318K temperatures at pH 7.0 (± 0.2) using the batch sorption method. In the kinetics study of arsenic (III) sorption, the sorption percentage was observed to remain nearly unchanged up to pH 9.0, thereafter only slight reduction in sorption percentage. The equilibrium sorption results were tested using the models of Langmuir and the Freundlich isotherm. The Langmuir model is the most fitted model for the sorption reaction. NHCAO was highly efficient in As(III) removal out of the water in the extensive range of pH and could be used for arsenic removal from contaminated water.

In Vitro and In Vivo Evaluation of Lactobacillus delbrueckii subsp. bulgaricus KLDS1.0207 for the Alleviative Effect on Lead Toxicity.

PubMed

Li, Bailiang; Jin, Da; Yu, Shangfu; Etareri Evivie, Smith; Muhammad, Zafarullah; Huo, Guicheng; Liu, Fei

2017-08-08

Lead (Pb) is a toxic contaminating heavy metal that can cause a variety of hazardous effects to both humans and animals. In the present study, Lactobacillus delbrueckii subsp. bulgaricus KLDS1.0207 ( L. bulgaricus KLDS1.0207), which has a remarkable Pb binding capacity and Pb tolerance, was selected for further study. It was observed that the thermodynamic and kinetic model of L. bulgaricus KLDS1.0207 Pb binding respectively fit with the Langmuir-Freundlich model and the pseudo second-order kinetic model. Scanning electron microscopy and energy dispersive spectroscopy analysis disclosed that the cell surfaces were covered with Pb and that carbon and oxygen elements were chiefly involved in Pb binding. Combined with Fourier transform infrared spectroscopy analysis, it was revealed that the carboxyl, phosphoryl, hydroxyl, amino and amide groups were the main functional groups involved in the Pb adsorption. The protective effects of L. bulgaricus KLDS1.0207 against acute Pb toxicity in mice was evaluated by prevention and therapy groups, the results in vivo showed that L. bulgaricus KLDS1.0207 treatment could reduce mortality rates, effectively increase Pb levels in the feces, alleviate tissue Pb enrichment, improve the antioxidant index in the liver and kidney, and relieve renal pathological damage. Our findings show that L. bulgaricus KLDS1.0207 can be used as a potential probiotic against acute Pb toxicity.

Biosorption of Zn(II) from industrial effluents using sugar beet pulp and F. vesiculosus: From laboratory tests to a pilot approach.

PubMed

Castro, Laura; Blázquez, M Luisa; González, Felisa; Muñoz, Jesús A; Ballester, Antonio

2017-11-15

The aim of this work was to demonstrate the feasibility of the application of biosorption in the treatment of metal polluted wastewaters through the development of several pilot plants to be implemented by the industry. The use as biosorbents of both the brown seaweed Fucus vesiculosus and a sugar beet pulp was investigated to remove heavy metal ions from a wastewater generated in an electroplating industry: Industrial Goñabe (Valladolid, Spain). Batch experiments were performed to study the effects of pH, contact time and initial metal concentration on metal biosorption. It was observed that the adsorption capacity of the biosorbents strongly depended on the pH, increasing as the pH rises from 2 to 5. The adsorption kinetic was studied using three models: pseudo first order, pseudo second order and Elovich models. The experimental data were fitted to Langmuir and Freundlich isotherm models and the brown alga F. vesiculosus showed higher metal uptake than the sugar beet pulp. The biomasses were also used for zinc removal in fixed-bed columns. The performance of the system was evaluated in different experimental conditions. The mixture of the two biomasses, the use of serial columns and the inverse flow can be interesting attempts to improve the biosorption process for large-scale applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Graphene oxide coated with porous iron oxide ribbons for 2, 4-Dichlorophenoxyacetic acid (2,4-D) removal.

PubMed

Nethaji, S; Sivasamy, A

2017-04-01

Graphene oxide (GO) was prepared from commercially available graphite powder. Porous iron oxide ribbons were grown on the surface of GO by solvothermal process. The prepared GO-Fe 3 O 4 nanocomposites are characterized by FT-IR, XRD, VSM, SEM, TEM, Raman spectroscopy, surface functionality and zero point charge studies. The morphology of the iron oxide ribbons grown on GO is demonstrated with TEM at various magnifications. The presence of magnetite nanoparticles is evident from XRD peaks and the magnetization value is found to be 37.28emu/g. The ratio of intensity of D-peak to G-peak from Raman spectrum is 0.995. The synthesized Graphene oxide-Fe 3 O 4 nanocomposites (GO-Fe 3 O 4 ) were explored for its surface adsorptive properties by using a model organic compound, 2,4-Dichlorophenoxy acetic acid (2,4-D) from aqueous solution. Batch adsorption studies were performed and the equilibrium data are modelled with Langmuir, Freundlich and Temkin isotherms. The maximum monolayer capacity from Langmuir isotherm is 67.26mg/g. Kinetic studies were also carried out and the studied adsorption process followed pseudo second-order rate equation. Mechanism of the adsorption process is studied by fitting the data with intraparticle diffusion model and Boyd plot. The studied adsorption process is both by film diffusion and intraparticle diffusion. Copyright © 2017 Elsevier Inc. All rights reserved.

Removal of Crystal Violet by Using Reduced-Graphene-Oxide-Supported Bimetallic Fe/Ni Nanoparticles (rGO/Fe/Ni): Application of Artificial Intelligence Modeling for the Optimization Process.

PubMed

Ruan, Wenqian; Hu, Jiwei; Qi, Jimei; Hou, Yu; Cao, Rensheng; Wei, Xionghui

2018-05-22

Reduced-graphene-oxide-supported bimetallic Fe/Ni nanoparticles were synthesized in this study for the removal of crystal violet (CV) dye from aqueous solutions. This material was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS), Raman spectroscopy, N₂-sorption, and X-ray photoelectron spectroscopy (XPS). The influence of independent parameters (namely, initial dye concentration, initial pH, contact time, and temperature) on the removal efficiency were investigated via Box⁻Behnken design (BBD). Artificial intelligence (i.e., artificial neural network, genetic algorithm, and particle swarm optimization) was used to optimize and predict the optimum conditions and obtain the maximum removal efficiency. The zero point of charge (pH ZPC ) of rGO/Fe/Ni composites was determined by using the salt addition method. The experimental equilibrium data were fitted well to the Freundlich model for the evaluation of the actual behavior of CV adsorption, and the maximum adsorption capacity was estimated as 2000.00 mg/g. The kinetic study discloses that the adsorption processes can be satisfactorily described by the pseudo-second-order model. The values of Gibbs free energy change (Δ G ⁰), entropy change (Δ S ⁰), and enthalpy change (Δ H ⁰) demonstrate the spontaneous and endothermic nature of the adsorption of CV onto rGO/Fe/Ni composites.

Comparative evaluation of adsorption kinetics of diclofenac and isoproturon by activated carbon.

PubMed

Torrellas, Silvia A; Rodriguez, Araceli R; Escudero, Gabriel O; Martín, José María G; Rodriguez, Juan G

2015-01-01

Adsorption mechanism of diclofenac and isoproturon onto activated carbon has been proposed using Langmuir and Freundlich isotherms. Adsorption capacity and optimum adsorption isotherms were predicted by nonlinear regression method. Different kinetic equations, pseudo-first-order, pseudo-second-order, intraparticle diffusion model and Bangham kinetic model, were applied to study the adsorption kinetics of emerging contaminants on activated carbon in two aqueous matrices.

Uptake of HNO3 on hexane and aviation kerosene soots.

PubMed

Talukdar, Ranajit K; Loukhovitskaya, Ekaterina E; Popovicheva, Olga B; Ravishankara, A R

2006-08-10

The uptake of HNO(3) on aviation kerosene (TC-1) soot was measured as a function of temperature (253-295 K) and the partial pressure of HNO(3), and the uptake of HNO(3) on hexane soot was studied at 295 K and over a limited partial pressure of HNO(3). The HNO(3) uptake was mostly reversible and did not release measurable amounts of gas-phase products such as HONO, NO(3), NO(2) or N(2)O(5). The heat of adsorption of HNO(3) on soot was dependent on the surface coverage. The isosteric heats of adsorption, Delta(0)H(isosteric), were determined as a function of coverage. Delta(0)H(isosteric) values were in the range -16 to -13 kcal mol(-1). The heats of adsorption decrease with increasing coverage. The adsorption data were fit to Freundlich and to Langmuir-Freundlich isotherms. The heterogeneity parameter values were close to 0.5, which suggested that a HNO(3) molecule can occupy two sites on the surface with or without being dissociated and that the soot surface could be nonuniform. Surface FTIR studies on the interaction of soot with HNO(3) did not reveal formation of any minor product such as organic nitrate or nitro compound on the soot surface. Using our measured coverage, we calculate that the partitioning of gas-phase nitric acid to black carbon aerosol is not a significant loss process of HNO(3) in the atmosphere.

Phenol adsorption on surface-functionalized iron oxide nanoparticles: modeling of the kinetics, isotherm, and mechanism

NASA Astrophysics Data System (ADS)

Yoon, Soon Uk; Mahanty, Biswanath; Ha, Hun Moon; Kim, Chang Gyun

2016-06-01

Phenol adsorption from aqueous solution was carried out using uncoated and methyl acrylic acid (MAA)-coated iron oxide nanoparticles (NPs), having size <10 nm, as adsorbents. Batch adsorption studies revealed that the phenol removal efficiency of MAA-coated NPs (950 mg g-1) is significantly higher than that of uncoated NPs (550 mg g-1) under neutral to acidic conditions. However, this improvement disappears above pH 9. The adsorption data under optimized conditions (pH 7) were modeled with pseudo-first- and pseudo-second-order kinetics and subjected to Freundlich and Langmuir isotherms. The analysis determined that pseudo-second-order kinetics and the Freundlich model are appropriate for both uncoated and MAA-coated NPs (all R 2 > 0.98). X-ray photoelectron spectroscopy analysis of pristine and phenol-adsorbed NPs revealed core-level binding energy and charge for Fe(2 s) and O(1 s) on the NP surfaces. The calculations suggest that phenol adsorption onto MAA-coated NPs is a charge transfer process, where the adsorbate (phenol) acts as an electron donor and the NP surface (Fe, O) as an electron acceptor. However, a physisorption process appears to be the relevant mechanism for uncoated NPs.

Adsorption of hydraulic fracturing fluid components 2-butoxyethanol and furfural onto granular activated carbon and shale rock.

PubMed

Manz, Katherine E; Haerr, Gregory; Lucchesi, Jessica; Carter, Kimberly E

2016-12-01

The objective of this study was to understand the adsorption ability of a surfactant and a non-surfactant chemical additive used in hydraulic fracturing onto shale and GAC. Experiments were performed at varying temperatures and sodium chloride concentrations to establish these impacts on the adsorption of the furfural (a non-surfactant) and 2-Butoxyethanol (2-BE) (a surfactant). Experiments were carried out in continuously mixed batch experiments with Langmuir and Freundlich isotherm modeling. The results of the experiments showed that adsorption of these compounds onto shale does not occur, which may allow these compounds to return to the surface in flowback and produced waters. The adsorption potential for these chemicals onto GAC follows the assumptions of the Langmuir model more strongly than those of the Freundlich model. The results show uptake of furfural and 2-BE occurs within 23 h in the presence of DI water, 0.1 mol L -1 sodium chloride, and in lab synthesized hydraulic fracturing brine. Based on the data, 83% of the furfural and 62% of the 2-BE was adsorbed using GAC. Copyright © 2016 Elsevier Ltd. All rights reserved.

Extraction of anthocyanins from black bean canning wastewater with macroporous resins.

PubMed

Wang, Xiaoxi; Hansen, Conly; Allen, Karin

2014-02-01

This study investigated purification of anthocyanins from black bean canning wastewater by column chromatography with 5 types of macroporous resins (Diaion Hp20, Sepabeads Sp70, Sepabeads Sp207, Sepabeads Sp700, and Sepabeads Sp710). By-product of canned black beans was partially purified by filtration, in anticipation of higher performance during column chromatography. Equilibrium adsorption isotherms were measured and analyzed using Langmuir and Freundlich isotherm models. Both Langmuir (all R² ≥ 0.98) and Freundlich (all R² ≥ 0.97) models can describe the adsorption process of anthocyanins from black bean canning wastewater using the tested resins. The adsorption and desorption behaviors of anthocyanins were studied using a dynamic method on the 5 types of resins, and Sp700 presented the highest adsorption capacity (39 ± 4 mg/g; P < 0.05) as well as desorption capacity (19 ± 2%; P < 0.05), indicating that of the resins examined, Sp700 is a better candidate for purification of anthocyanins from black bean canning wastewater. © 2014 Institute of Food Technologists®

Nitrogen-functionalization biochars derived from wheat straws via molten salt synthesis: An efficient adsorbent for atrazine removal.

PubMed

Yang, Fan; Sun, Lili; Xie, Weiling; Jiang, Qun; Gao, Yan; Zhang, Wei; Zhang, Ying

2017-12-31

N-doped porous carbon sheets (NPCS) resulted from wheat straws are fabricated through using molten salts via the carbonization-functionalization progress, which show unique hierarchical structure, large pore volume and high surface area with affluent micropores. Results indicate that there exist many hierarchical pores consisting of the single carbon sheet with ultrathin nature, owing to the template role of molten salt mixtures at high temperature. Such superior structure can bring about desired performance of adsorption capacity of 82.8mg/g and quick adsorption rate of 1.43L/(gh) with an initial concentration of 35mg/L at 25°C. Langmuir and Freundlich models are adopted to interpret the adsorption behavior of atrazine and modified Freundlich and intraparticle diffusion (IPD) models are employed to characterize the dynamics of adsorption. Furthermore, nitrogen-functionalization biochars via molten salt synthesis should be further developed as a one-pot methodology to produce N-doped carbons, opening up a feasible approach for resource utilization of crop straws and other biomass wastes. Copyright © 2017 Elsevier B.V. All rights reserved.

Adsorption of Cu(II) on Oxidized Multi-Walled Carbon Nanotubes in the Presence of Hydroxylated and Carboxylated Fullerenes

PubMed Central

Wang, Jing; Li, Zhan; Li, Shicheng; Qi, Wei; Liu, Peng; Liu, Fuqiang; Ye, Yuanlv; Wu, Liansheng; Wang, Lei; Wu, Wangsuo

2013-01-01

The adsorption of Cu(II) on oxidized multi-walled carbon nanotubes (oMWCNTs) as a function of contact time, pH, ionic strength, temperature, and hydroxylated fullerene (C60(OH)n) and carboxylated fullerene (C60(C(COOH)2)n) were studied under ambient conditions using batch techniques. The results showed that the adsorption of Cu(II) had rapidly reached equilibrium and the kinetic process was well described by a pseudo-second-order rate model. Cu(II) adsorption on oMWCNTs was dependent on pH but independent of ionic strength. Compared with the Freundlich model, the Langmuir model was more suitable for analyzing the adsorption isotherms. The thermodynamic parameters calculated from temperature-dependent adsorption isotherms suggested that Cu(II) adsorption on oMWCNTs was spontaneous and endothermic. The effect of C60(OH)n on Cu(II) adsorption of oMWCNTs was not significant at low C60(OH)n concentration, whereas a negative effect was observed at higher concentration. The adsorption of Cu(II) on oMWCNTs was enhanced with increasing pH values at pH < 5, but decreased at pH ≥ 5. The presence of C60(C(COOH)2)n inhibited the adsorption of Cu(II) onto oMWCNTs at pH 4–6. The double sorption site model was applied to simulate the adsorption isotherms of Cu(II) in the presence of C60(OH)n and fitted the experimental data well. PMID:24009683

Surface complexation modeling calculation of Pb(II) adsorption onto the calcined diatomite

NASA Astrophysics Data System (ADS)

Ma, Shu-Cui; Zhang, Ji-Lin; Sun, De-Hui; Liu, Gui-Xia

2015-12-01

Removal of noxious heavy metal ions (e.g. Pb(II)) by surface adsorption of minerals (e.g. diatomite) is an important means in the environmental aqueous pollution control. Thus, it is very essential to understand the surface adsorptive behavior and mechanism. In this work, the Pb(II) apparent surface complexation reaction equilibrium constants on the calcined diatomite and distributions of Pb(II) surface species were investigated through modeling calculations of Pb(II) based on diffuse double layer model (DLM) with three amphoteric sites. Batch experiments were used to study the adsorption of Pb(II) onto the calcined diatomite as a function of pH (3.0-7.0) and different ionic strengths (0.05 and 0.1 mol L-1 NaCl) under ambient atmosphere. Adsorption of Pb(II) can be well described by Freundlich isotherm models. The apparent surface complexation equilibrium constants (log K) were obtained by fitting the batch experimental data using the PEST 13.0 together with PHREEQC 3.1.2 codes and there is good agreement between measured and predicted data. Distribution of Pb(II) surface species on the diatomite calculated by PHREEQC 3.1.2 program indicates that the impurity cations (e.g. Al3+, Fe3+, etc.) in the diatomite play a leading role in the Pb(II) adsorption and dominant formation of complexes and additional electrostatic interaction are the main adsorption mechanism of Pb(II) on the diatomite under weak acidic conditions.

Competition and enhancement effect in coremoval of atenolol and copper by an easily regenerative magnetic cation exchange resin.

PubMed

Li, Qimeng; Wang, Zheng; Li, Qiang; Shuang, Chendong; Zhou, Qing; Li, Aimin; Gao, Canzhu

2017-07-01

This paper aimed to investigate the removal of combined Cu 2+ and atenolol (ATL) in aqueous solution by using a newly synthesized magnetic cation exchange resin (MCER) as the adsorbent. The MCER exhibited efficient removal performance in sole, binary, pre-loading and saline systems. The adsorption kinetics of Cu 2+ and ATL fitted both pseudo-first-order and pseudo-second order model, while better described by pseudo-second order model in binary system. In mixed Cu 2+ and ATL solution, the adsorption of ATL was suppressed due to direct competition of carboxylic groups, while Cu 2+ adsorption was enhanced because of the formation of surface complexes. This increasing in heterogeneity was demonstrated by adsorption isotherms, which were more suitable for Freundlich model in binary system, while better described by Langmuir model in sole system. As proved by FTIR and XPS spectra, both amino and hydroxyl groups of ATL could form complexes with Cu 2+ . Decomplexing-bridging interaction was elucidated as the leading mechanism in coremoval of Cu 2+ and ATL, which involved [Cu-ATL] decomplexing and newly created Cu- or ATL sites for additional bridging. For saline system, the resulting competition and enhancement effects in mixed solution were amplified with the addition of co-existing cations. Moreover, the MCER could be effectively regenerated by 0.01 M HCl solution and maintain high stability over 5 adsorption-desorption cycles, which render it great potential for practical applications. Copyright © 2017. Published by Elsevier Ltd.

Activated carbon adsorption of quinolone antibiotics in water: Performance, mechanism, and modeling.

PubMed

Fu, Hao; Li, Xuebing; Wang, Jun; Lin, Pengfei; Chen, Chao; Zhang, Xiaojian; Suffet, I H Mel

2017-06-01

The extensive use of antibiotics has led to their presence in the aquatic environment, and introduces potential impacts on human and ecological health. The capability of powdered activated carbon (PAC) to remove six frequently used quinolone (QN) antibiotics during water treatment was evaluated to improve drinking water safety. The kinetics of QN adsorption by PAC was best described by a pseudo second-order equation, and the adsorption capacity was well described by the Freundlich isotherm equation. Isotherms measured at different pH showed that hydrophobic interaction, electrostatic interaction, and π-π dispersion force were the main mechanisms for adsorption of QNs by PAC. A pH-dependent isotherm model based on the Freundlich equation was developed to predict the adsorption capacity of QNs by PAC at different pH values. This model had excellent prediction capabilities under different laboratory scenarios. Small relative standard derivations (RSDs), i.e., 0.59%-0.92% for ciprofloxacin and 0.09%-3.89% for enrofloxacin, were observed for equilibrium concentrations above the 0.3mg/L level. The RSDs increased to 11.9% for ciprofloxacin and 32.1% for enrofloxacin at μg/L equilibrium levels, which is still acceptable. This model could be applied to predict the adsorption of other chemicals having different ionized forms. Copyright © 2016. Published by Elsevier B.V.

High surface area mesoporous activated carbon-alginate beads for efficient removal of methylene blue.

PubMed

Nasrullah, Asma; Bhat, A H; Naeem, Abdul; Isa, Mohamed Hasnain; Danish, Mohammed

2018-02-01

High surface area mesoporous activated carbon-alginate (AC-alginate) beads were successfully synthesized by entrapping activated carbon powder derived from Mangosteen fruit peel into calcium-alginate beads for methylene blue (MB) removal from aqueous solution. The structure and surface characteristics of AC-alginate beads were analyzed using Fourier transform infra-red (FTIR) spectroscopy, scanning electron microscopy (SEM) and surface area analysis (S BET ), while thermal properties were tested using thermogravimetric analysis (TGA). The effect of AC-alginate dose, pH of solution, contact time, initial concentration of MB solution and temperature on MB removal was elucidated. The results showed that the maximum adsorption capacity of 230mg/g was achieved for 100mg/L of MB solution at pH 9.5 and temperature 25°C. Furthermore, the adsorption of MB on AC-alginate beads followed well pseudo-second order equation and equilibrium adsorption data were better fitted by the Freundlich isotherm model. The findings reveal the feasibility of AC-alginate beads composite to be used as a potential and low cost adsorbent for removal of cationic dyes. Copyright © 2017 Elsevier B.V. All rights reserved.

Natural organic matter (NOM) adsorption to multi-walled carbon nanotubes: effect of NOM characteristics and water quality parameters.

PubMed

Hyung, Hoon; Kim, Jae-Hong

2008-06-15

The effect of natural organic matter (NOM) characteristics and water quality parameters on NOM adsorption to multiwalled carbon nanotubes (MWNT) was investigated. Isotherm experiment results were fitted well with a modified Freundlich isotherm model that took into account the heterogeneous nature of NOM. The preferential adsorption of the higher molecular weight fraction of NOM was observed by size exclusion chromatographic analysis. Experiments performed with various NOM samples suggested that the degree of NOM adsorption varied greatly depending on the type of NOM and was proportional to the aromatic carbon content of NOM. The NOM adsorption to MWNT was also dependent on water quality parameters: adsorption increased as pH decreased and ionic strength increased. As a result of NOM adsorption to MWNT, a fraction of MWNT formed a stable suspension in water and the concentration of MWNT suspension depended on the amount of NOM adsorbed per unit mass of MWNT. The amount of MWNT suspended in water was also affected by ionic strength and pH. The findings in this study suggested that the fate and transport of MWNT in natural systems would be largely influenced by NOM characteristics and water quality parameters.

Biosorption of clofibric acid and carbamazepine in aqueous solution by agricultural waste rice straw.

PubMed

Liu, Zhanguang; Zhou, Xuefei; Chen, Xiaohua; Dai, Chaomeng; Zhang, Juan; Zhang, Yalei

2013-12-01

Due to their widespread use, clofibric acid (CA) and carbamazepine (CBZ) have been frequently detected simultaneously at relatively high concentrations in aquatic environments. In this study, agricultural waste rice straw was employed as a potentially low-cost, effective and easy-to-operate biosorbent (RSB) to remove CA and CBZ. The adsorption of both pharmaceuticals followed pseudo second-order kinetics, and intraparticle diffusion was an important rate-limiting step. The adsorption isotherms of both drugs were fit well with Freundlich model. The adsorption of CA onto RSB was exothermic and was more likely to be dominated by physical processes, while the adsorption of CBZ was endothermic. Solution pH was determined to be the most important factor for CA adsorption, such that the adsorption capacity of CA onto RSB increased with the decline of solution pH. In the lower range of solution pH below 3.1, the CA removal efficiency was enhanced with the increase of biosorbent dosage. The CBZ removal efficiency was enhanced with the increase of RSB dosage without pH control. The maximum adsorption capacities were 126.3 mg/g for CA and 40.0 mg/g for CBZ.

Sorption kinetics, isotherms, and mechanism of aniline aerofloat to agricultural soils with various physicochemical properties.

PubMed

Xiang, Lei; Xiao, Tao; Mo, Ce-Hui; Zhao, Hai-Ming; Li, Yan-Wen; Li, Hui; Cai, Quan-Ying; Zhou, Dong-Mei; Wong, Ming-Hung

2018-06-15

Aniline aerofloat (AAF), a high-toxic organic flotation reagent, is widely used in mineral processing industry. However, little information on its environmental fate is available. AAF sorption to four types of agricultural soils at low concentrations (1-10 mg/L) was investigated using batch experiments. AAF sorption kinetics involved both boundary layer diffusion and intraparticle diffusion, following pseudo-second-order kinetics with equilibrium time within 120 min. Both Langmuir and Freundlich models fitted well the AAF sorption with the former better. Sorption of AAF to soils was a spontaneous and favorable physical sorption that was controlled by ion bridge effect and hydrophobic interaction that was related to van der Waals force and π-π coordination based on FTIR analyses. AAF sorption was remarkably affected by soil constituents, positively correlating with the contents of organic matter and clay. The relatively higher logK oc values (3.53-4.66) of AAF at environmental concentrations (1-5 mg/L) imply that soils are serving as a sink of AAF from beneficiation wastewater, posing great potential risks to environment and human health. Copyright © 2018 Elsevier Inc. All rights reserved.

Adsorption of methyl orange from aqueous solution using chitosan/diatomite composite.

PubMed

Zhao, Peng; Zhang, Runhu; Wang, Jianglin

2017-04-01

A novel chitosan/diatomite composite was prepared by a simple mixture in the mass ratio to remove methyl orange (MO) from aqueous media in this study. The composite adsorbent was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy analysis. The parameters to influence the adsorption of MO were studied under such conditions as kinetics, adsorption isotherm, pH effect, and thermodynamics. The results revealed that adsorption of MO was initially rapid and the equilibrium time was reached after 40 min. The optimal value of the pH was 5.0 for better adsorption. The equilibrium data were well fitted to the Langmuir isotherm compared to the Freundlich isotherm, and exhibited the highest capacity and a removal rate of 88.37% under an initial dye concentration of 50 mg/L. The kinetic data were well described by the pseudo-second order model. The thermodynamic calculations revealed that the sorption was viable, spontaneous, and exothermic under the conditions studied. In addition, the chitosan/diatomite composite had good adsorption and desorption performance with respect to reusability after six cycles. These results showed that the chitosan/diatomite could be considered as a potential adsorbent for the removal of MO in aqueous solution.

Application of magnetic molecularly imprinted polymers for extraction of imidacloprid from eggplant and honey.

PubMed

Kumar, Niranjan; Narayanan, Neethu; Gupta, Suman

2018-07-30

A magnetic molecularly imprinted polymer (MMIP) adsorbent for imidacloprid was prepared using non-covalent approach with functionalized nano Fe 3 O 4 particles (magnetic cores), imidacloprid (template), acrylic acid (functional monomer), ethylene glycol dimethacrylate (cross linker) and azobisisobutyronitrile (initiator) and used for selective separation of imidacloprid from honey and vegetable samples. The polymers were characterized using FT-IR spectroscopy, SEM and TEM images. For analysis of imidacloprid LC-MS/MS equipment was used. Adsorption kinetics was best explained by pseudo-second-order kinetic model. Adsorption data fitted well into linearized Freundlich equation (R 2  > 0.98). Scatchard plot analysis indicates the presence of two classes of binding sites in the MMIPs with the C max of 1889.6 µg g -1 and 65448.9 µg g -1 , respectively. MMIPs demonstrated much higher affinity for imidacloprid over structurally similar analogues acetamiprid (α = 23.59) and thiamethoxam (α = 17.15). About 87.1 ± 5.0% and 90.6 ± 5.6% of the added imidacloprid was recovered from MMIPs in case of fortified eggplant and honey samples, respectively. Copyright © 2018 Elsevier Ltd. All rights reserved.

Biosorption of copper and lead ions by waste beer yeast.

PubMed

Han, Runping; Li, Hongkui; Li, Yanhu; Zhang, Jinghua; Xiao, Huijun; Shi, Jie

2006-10-11

Locally available waste beer yeast, a byproduct of brewing industry, was found to be a low cost and promising adsorbent for adsorbing copper and lead ions from wastewater. In this work, biosorption of copper and lead ions on waste beer yeast was investigated in batch mode. The equilibrium adsorptive quantity was determined to be a function of the solution pH, contact time, beer yeast concentration, salt concentration and initial concentration of copper and lead ions. The experimental results were fitted well to the Langmuir and Freundlich model isotherms. According to the parameters of Langmuir isotherm, the maximum biosorption capacities of copper and lead ions onto beer yeast were 0.0228 and 0.0277 mmol g(-1) at 293 K, respectively. The negative values of the standard free energy change (DeltaG degrees ) indicate spontaneous nature of the process. Competitive biosorption of two metal ions was investigated in terms of sorption quantity. The amount of one metal ion adsorbed onto unit weight of biosorbent (q(e)) decreased with increasing the competing metal ion concentration. The binding capacity for lead is more than for copper. Ion exchange is probably one of the main mechanism during adsorptive process.

Removal of Free Fatty Acid from Plant Oil by the Adsorption Process

NASA Astrophysics Data System (ADS)

Chung, Tsair-Wang; Wu, Yi-Ling; Hsu, Shih-Hong

2018-05-01

The food oil refinery process for deacidification is ususally conducted by the neutralization after degumming. In this study, commercialized resins will be used as adsorbents to remove the free fatty acid (FFA) in food oil without using any solvent. Applying this environmental friendly green process, the energy efficiency will be increased and the waste water will be reduced compared to the traditional process. The selected adsorbent can be reused which may reduce the process cost. Instead of using alkali neutralization, the proposed process may reduce the concern of food oil security. The commercial resins A26OH and IRA900Cl were compared as adsorbents to remove the FFA in deacidification for refinery of food oil without adding any alkali chemicals. This process will be conducted to remove the FFA form peanut oil in this study. Besides, this study will get the adsorption isotherms for one of the better sorbents of A26OH or IRA900Cl to remove FFA from peanut oil under 25, 35, and 45°C. The Langmuir and Freundlich isotherm models were compared to fit the experimental data. The obtained isotherm data is important for the adsorption system design.

A study of equilibrium and FTIR, SEM/EDS analysis of trimethoprim adsorption onto K10

NASA Astrophysics Data System (ADS)

Bekçi, Zehra; Seki, Yoldaş; Kadir Yurdakoç, M.

2007-02-01

The sorption behavior of K10, a type of montmorillonite for trimethoprim (TMP) drug, was studied by using batch technique under different pH and temperature. The interaction between K10 and TMP was investigated using SEM, and FTIR. It was observed that adsorption was increased between pH 2.5 and 6.3. By performing kinetic experiments, the pseudo-second-order kinetic model provides the best fit for TMP adsorption onto K10 montmorillonite. The sorption of TMP reached the equilibrium state after 6 h sorption time and has been described by using Langmuir, Freundlich and Dubinin-Radushkevich equations to obtain adsorption capacity values. The results indicate that the relative adsorption capacity values ( Kf) are decreasing with the increase of temperature in the range of 298-318 K. The sorption energy values obtained from DR isotherm show that sorption of TMP onto K10 can be explained by ion exchange mechanism at 298, 308 and 318 K. The thermodynamic studies were conducted to find the thermodynamic parameters Δ H°, Δ S° and Δ G°. It was determined that adsorption process is spontaneous and exothermic in nature.

Aminopropyl-functionalized mesoporous carbon (APTMS-CMK-3) as effective phosphate adsorbent

NASA Astrophysics Data System (ADS)

Yang, Yanju; Wang, Juanjuan; Qian, Xiaoqing; Shan, Yuhua; Zhang, Haipeng

2018-01-01

Excess phosphate discharge into water bodies can lead to severe eutrophication. Adsorption has been considered as one of the most effective approaches for phosphate removal and recovery. A new aminopropyl-functionalized mesoporous carbon CMK-3 (denoted as APTMS-CMK-3) was prepared and the materials were used as adsorbents for the removal of phosphate in water. The structure, functional groups and surface charge of the materials were characterized by X-ray powder diffraction, transmission electron microscope, N2 adsorption-desorption, elemental analysis, Fourier transform infrared spectra, X-ray photoelectron spectroscopy and zeta potential measurements. The effects of contact time, initial phosphate concentration, solution pH, coexisting anions and dissolved humic acid were studied. The adsorption capacity of APTMS-CMK-3 was 38.09 mg g-1 at the equilibrium concentration of 49.06 mg L-1, and the adsorption data were well fitted with the Freundlich model. As for the reuse of APTMS-CMK-3, a relatively stable adsorption performance was observed after five adsorption-desorption cycles. Therefore, the way of grafting aminopropyl groups on the CMK-3 efficiently enhanced the capability for phosphate adsorption, indicating that it could be used as potential adsorbents for the removal of phosphate in water.

Adsorption of mixtures of nutrients and heavy metals in simulated urban stormwater by different filter materials.

PubMed

Reddy, Krishna R; Xie, Tao; Dastgheibi, Sara

2014-01-01

In recent years, several best management practices have been developed for the removal of different types of pollutants from stormwater runoff that lead to effective stormwater management. Filter materials that remove a wide range of contaminants have great potential for extensive use in filtration systems. In this study, four filter materials (calcite, zeolite, sand, and iron filings) were investigated for their adsorption and efficiency in the removal of nutrients and heavy metals when they exist individually versus when they co-exist. Laboratory batch experiments were conducted separately under individual and mixed contaminants conditions at different initial concentrations. Adsorption capacities varied under the individual and mixed contaminant conditions due to different removal mechanisms. Most filter materials showed lower removal efficiency under mixed contaminant conditions. In general, iron filings were found effective in the removal of nutrients and heavy metals simultaneously to the maximum levels. Freundlich and Langmuir isotherms were used to model the batch adsorption results and the former better fitted the experimental results. Overall, the results indicate that the filter materials used in this study have the potential to be effective media for the treatment of nutrients and heavy metals commonly found in urban stormwater runoff.

Synthesis, characterization, and mercury adsorption properties of hybrid mesoporous aluminosilicate sieve prepared with fly ash.

PubMed

Liu, Minmin; Hou, Li-An; Xi, Beidou; Zhao, Ying; Xia, Xunfeng

2013-05-15

A novel hybrid mesoporous aluminosilicate sieve (HMAS) was prepared with fly ash and impregnated with zeolite A precursors. This improved the mercury adsorption of HMAS compared to original MCM-41. The HMAS was characterized by X-ray diffraction (XRD), nitrogen adsorption-desorption, Fourier transform infrared (FTIR) analysis, transmission electron microscopy (TEM) images and 29 Si and 27 Al magic angle spinning nuclear magnetic resonance (MAS NMR) spectra. These showed that the HMAS structure was still retained after impregnated with zeolite A. But the surface area and pore diameter of HMAS decreased due to pore blockage. Adsorption of mercury from aqueous solution was studied on untreated MCM-41and HMAS. The mercury adsorption rate of HMAS was higher than that of origin MCM-41. The adsorption of mercury was investigated on HMAS regarding the pH of mercury solution, initial mercury concentration, and the reaction temperature. The experimental data fit well to Langmuir and Freundlich isotherm models. The Dublin-Radushkevich isotherm and the characterization show that the mercury adsorption on HMAS involved the ion-exchange mechanisms. In addition, the thermodynamic parameters suggest that the adsorption process was endothermic in nature. The adsorption of mercury on HMAS followed the first order kinetics.

Functionalized granular activated carbon and surface complexation with chromates and bi-chromates in wastewater.

PubMed

Singha, Somdutta; Sarkar, Ujjaini; Luharuka, Pallavi

2013-03-01

Cr(VI) is present in the aqueous medium as chromate (CrO4(2-)) and bi-chromate (HCrO4(-)). Functionalized granular activated carbons (FACs) are used as adsorbents in the treatment of wastewaters containing hexavalent chromium. The FACs are prepared by chemical modifications of granular activated carbons (GACs) using functionalizing agents like HNO3, HCl and HF. The Brunauer, Emmett and Teller surface areas of FAC-HCl (693.5m(2)/g), FAC-HNO3 (648.8m(2)/g) and FAC-HF (726.2m(2)/g) are comparable to the GAC (777.7m(2)/g). But, the adsorption capacity of each of the FAC-HNO3, FAC-HCl and FAC-HF is found to be higher than the GAC. The functional groups play an important role in the adsorption process and pH has practically no role in this specific case. The FACs have hydrophilic protonated external surfaces in particular, along with the functional surface sites capable to make complexes with the CrO4(2-) and HCrO4(-) present. Surface complex formation is maximized in the order FAC-HNO3>FAC-HF>FAC-HCl, in proportion to the total surface acidity. This is also confirmed by the well-known pseudo second-order kinetic model. Physi-sorption equilibrium isotherms are parameterized by using standard Freundlich and Langmuir models. Langmuir fits better. The formation of surface complexes with the functional groups and hexavalent chromium is also revealed in the images of field emission scanning electron micrograph; energy dispersive X-ray spectroscopy and Fourier transform infrared spectroscopy analysis after adsorption. The intra-particle diffusion is not the only rate-controlling factor. The Boyd's film diffusion model fits very well with R(2) as high as 98.1% for FAC-HNO3. This result demonstrates that the functionalization of the GAC by acid treatments would increase the diffusion rate, predominantly with a boundary layer diffusion effect. Copyright © 2013 Elsevier B.V. All rights reserved.

Study of colloidal properties of natural and Al-pillared smectite and removal of copper ions from an aqueous solution.

PubMed

Sartor, Lucas Resmini; de Azevedo, Antonio Carlos; Andrade, Gabriel Ramatis Pugliese

2015-01-01

In this study, an Al-pillared smectite was synthesized and changes in its colloidal properties were investigated. The pillaring solution was prepared by mixing 0.4 mol L(-1) NaOH and 0.2 mol L(-1) AlCl3.6H2O solutions. Intercalated clays were heated to obtain the pillared clay, and X-ray diffractometry (XRD), X-ray fluorescence (XRF), Fourier transform infrared (FTIR) spectroscopy and N2 sorption/desorption isotherms analysis were done to characterize the changes in clay properties. Moreover, adsorption experiments were carried out in order to evaluate the capacity of the pillared clays to remove Cu2+ from an aqueous solution and to characterize the interaction between adsorbent and adsorbate. The results indicate that the natural clay has a basal spacing of 1.26 nm, whereas the pillared clays reached 1.78 nm (500°C) and 1.80 nm (350°C) after calcination. XRF analysis revealed an increase in the Al3+ in the pillared clay as compared to the natural clay. The surface area and pore volume (micro and mesoporous) were higher for the pillared clays. Experimental data from the adsorption experiment were fit to Langmuir and Freundlich and Temkin adsorption models, and the former one was the best fit (highest r2 value) for all the clays and lower standard deviation (Δg%) for the natural clay. On the other hand, the Temkin model exhibited Δg% value lower for the pillared clays. Thermodynamics parameters demonstrate that the Cu2+ adsorption process is spontaneous for all the clays, but with higher values for the pillared materials. In addition, application of the Dubinin-Radushkevich model revealed that the bond between the metal and the clay are weak, characterizing a physisorption.

Role of black carbon in the sorption of polychlorinated dibenzo-p-dioxins and dibenzofurans at the Diamond Alkali superfund site, Newark Bay, New Jersey.

PubMed

Lambert, Matthew K; Friedman, Carey; Luey, Pamela; Lohmann, Rainer

2011-05-15

The sorption of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) to organic carbon (OC) and black carbon (BC) was measured in two sediment cores taken near the Diamond Alkali superfund site (DA) in the Passaic River and Newark Bay, New Jersey (U.S.A.). An OC partitioning model and a BC-inclusive, Freundlich distribution model were used to interpret measurements of freely dissolved PCDD/Fs using passive samplers in sediment incubations, together with measured sedimentary concentrations of OC, BC, and PCDD/Fs. Samples were also analyzed for polycyclic aromatic hydrocarbons (PAHs) as controls on the two distribution models. The OC partitioning model underpredicted the distribution of PAHs and PCDD/Fs by 10-100-fold. The Freundlich model predicted the distribution of PAHs at the DA to within a factor of 2-3 of observations. Black carbon-water partition coefficients (K(iBC)) for PCDD/Fs, derived from literature results of both field and laboratory studies differed up to 1000-fold from values derived from this study. Contrary to expectations, PCDDs displayed stronger sorption than either PCDFs or PAHs relative to their subcooled liquid aqueous solubilities. Even though the presence of BC in the sediments reduced the overall bioavailability of PCDD/Fs by >90%, the sediments at 2 m depth continue to display the highest pore water activities of PCDD/Fs.

Adsorptive Removal of Toxic Chromium from Waste-Water Using Wheat Straw and Eupatorium adenophorum

PubMed Central

Song, Dagang; Pan, Kaiwen; Tariq, Akash; Azizullah, Azizullah; Sun, Feng; Li, Zilong; Xiong, Qinli

2016-01-01

Environmental pollution with heavy metals is a serious issue worldwide posing threats to humans, animals and plants and to the stability of overall ecosystem. Chromium (Cr) is one of most hazardous heavy metals with a high carcinogenic and recalcitrant nature. Aim of the present study was to select low-cost biosorbent using wheat straw and Eupatorium adenophorum through simple carbonization process, capable of removing Cr (VI) efficiently from wastewater. From studied plants a low cost adsorbent was prepared for removing Cr (VI) from aqueous solution following very simple carbonization method excluding activation process. Several factors such as pH, contact time, sorbent dosage and temperature were investigated for attaining ideal condition. For analysis of adsorption equilibrium isotherm data, Langmuir, Freundlich and Temkin models were used while pseudo-first-order, pseudo-second-order, external diffusion and intra-particle diffusion models were used for the analysis of kinetic data. The obtained results revealed that 99.9% of Cr (VI) removal was observed in the solution with a pH of 1.0. Among all the tested models Langmuir model fitted more closely according to the data obtained. Increase in adsorption capacity was observed with increasing temperature revealing endothermic nature of Cr (VI). The maximum Cr (VI) adsorption potential of E. adenophorum and wheat straw was 89.22 mg per 1 gram adsorbent at 308K. Kinetic data of absorption precisely followed pseudo-second-order model. Present study revealed highest potential of E. adenophorum and wheat straw for producing low cost adsorbent and to remove Cr (VI) from contaminated water. PMID:27911906

Copper removal by algae Gelidium, agar extraction algal waste and granulated algal waste: kinetics and equilibrium.

PubMed

Vilar, Vítor J P; Botelho, Cidália M S; Boaventura, Rui A R

2008-03-01

Biosorption of copper ions by an industrial algal waste, from agar extraction industry has been studied in a batch system. This biosorbent was compared with the algae Gelidium itself, which is the raw material for agar extraction, and the industrial waste immobilized with polyacrylonitrile (composite material). The effects of contact time, pH, ionic strength (IS) and temperature on the biosorption process have been studied. Equilibrium data follow both Langmuir and Langmuir-Freundlich models. The parameters of Langmuir equilibrium model were: q(max)=33.0mgg(-1), K(L)=0.015mgl(-1); q(max)=16.7mgg(-1), K(L)=0.028mgl(-1) and q(max)=10.3mgg(-1), K(L)=0.160mgl(-1) respectively for Gelidium, algal waste and composite material at pH=5.3, T=20 degrees C and IS=0.001M. Increasing the pH, the number of deprotonated active sites increases and so the uptake capacity of copper ions. In the case of high ionic strengths, the contribution of the electrostatic component to the overall binding decreases, and so the uptake capacity. The temperature has little influence on the uptake capacity principally for low equilibrium copper concentrations. Changes in standard enthalpy, Gibbs energy and entropy during biosorption were determined. Kinetic data at different solution pH (3, 4 and 5.3) were fitted to pseudo-first-order and pseudo-second-order models. The adsorptive behaviour of biosorbent particles was modelled using a batch reactor mass transfer kinetic model, which successfully predicts Cu(II) concentration profiles.

Adsorptive Removal of Toxic Chromium from Waste-Water Using Wheat Straw and Eupatorium adenophorum.

PubMed

Song, Dagang; Pan, Kaiwen; Tariq, Akash; Azizullah, Azizullah; Sun, Feng; Li, Zilong; Xiong, Qinli

2016-01-01

Environmental pollution with heavy metals is a serious issue worldwide posing threats to humans, animals and plants and to the stability of overall ecosystem. Chromium (Cr) is one of most hazardous heavy metals with a high carcinogenic and recalcitrant nature. Aim of the present study was to select low-cost biosorbent using wheat straw and Eupatorium adenophorum through simple carbonization process, capable of removing Cr (VI) efficiently from wastewater. From studied plants a low cost adsorbent was prepared for removing Cr (VI) from aqueous solution following very simple carbonization method excluding activation process. Several factors such as pH, contact time, sorbent dosage and temperature were investigated for attaining ideal condition. For analysis of adsorption equilibrium isotherm data, Langmuir, Freundlich and Temkin models were used while pseudo-first-order, pseudo-second-order, external diffusion and intra-particle diffusion models were used for the analysis of kinetic data. The obtained results revealed that 99.9% of Cr (VI) removal was observed in the solution with a pH of 1.0. Among all the tested models Langmuir model fitted more closely according to the data obtained. Increase in adsorption capacity was observed with increasing temperature revealing endothermic nature of Cr (VI). The maximum Cr (VI) adsorption potential of E. adenophorum and wheat straw was 89.22 mg per 1 gram adsorbent at 308K. Kinetic data of absorption precisely followed pseudo-second-order model. Present study revealed highest potential of E. adenophorum and wheat straw for producing low cost adsorbent and to remove Cr (VI) from contaminated water.

Removal of gadolinium-based contrast agents: adsorption on activated carbon.

PubMed

Elizalde-González, María P; García-Díaz, Esmeralda; González-Perea, Mario; Mattusch, Jürgen

2017-03-01

Three carbon samples were employed in this work, including commercial (1690 m 2  g -1 ), activated carbon prepared from guava seeds (637 m 2  g -1 ), and activated carbon prepared from avocado kernel (1068 m 2  g -1 ), to study the adsorption of the following gadolinium-based contrast agents (GBCAs): gadoterate meglumine Dotarem®, gadopentetate dimeglumine Magnevist®, and gadoxetate disodium Primovist®. The activation conditions with H 3 PO 4 were optimized using a Taguchi methodology to obtain mesoporous materials. The best removal efficiency by square meter in a batch system in aqueous solution and model urine was achieved by avocado kernel carbon, in which mesoporosity prevails over microporosity. The kinetic adsorption curves were described by a pseudo-second-order equation, and the adsorption isotherms in the concentration range 0.5-6 mM fit the Freundlich equation. The chemical characterization of the surfaces shows that materials with a greater amount of phenolic functional groups adsorb the GBCA better. Adsorption strongly depends on the pH due to the combination of the following factors: contrast agent protonated forms and carbon surface charge. The tested carbon samples were able to adsorb 70-90% of GBCA in aqueous solution and less in model urine. This research proposes a method for the elimination of GBCA from patient urine before its discharge into wastewater.

Synthesis of molecularly imprinted polymers using acrylamide-β-cyclodextrin as a cofunctional monomer for the specific capture of tea saponins from the defatted cake extract of Camellia oleifera.

PubMed

Guo, Huiqin; Xiong, Jingjing; Ma, Wentian; Wu, Minghuo; Yan, Liushui; Li, Kexin; Liu, Yu

2016-11-01

Molecularly imprinted polymers were synthesized using mixed tea saponins as a template and acrylamide-β-cyclodextrin as a cofunctional monomer for the specific binding and purification of tea saponins from the defatted cake extract of Camellia oleifera. The adsorption properties of the prepared polymers were systematically evaluated including adsorption kinetics, adsorption isotherms, and selective recognition characteristics. It showed that the adsorption kinetics followed the pseudo first-order kinetic model (R 2 = 0.995) with an equilibrium time of 3 h, adsorption isotherm data fitted well with the Langmuir-Freundlich model (R 2 = 0.984) with an adsorption capacity of 14.23 mg/g. The relative selectivity coefficient (k´) in the presence of the analogues glycyrrhizic acid and glycyrrhetinic acid were 1.16 and 17.21, respectively. The performance of the molecularly imprinted polymers as solid-phase extraction materials was investigated and the results indicated that using acrylamide-β-cyclodextrin as a cofunctional monomer improved both the adsorption capacity and active sites stability of the imprinted polymers. The solid-phase extraction using the polymers as packing materials was subsequently applied for the separation of tea saponins in raw C. oleifera press extract, and targets were obtained with a purity reaching 89%. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Adsorption of ammonium and phosphate by feather protein based semi-interpenetrating polymer networks hydrogel as a controlled-release fertilizer.

PubMed

Su, Yuan; Liu, Jia; Yue, Qinyan; Li, Qian; Gao, Baoyu

2014-01-01

A new feather protein-grafted poly(potassium acrylate)/polyvinyl alcohol (FP-g-PKA/PVA) semi-interpenetrating polymer networks (semi-IPNs) hydrogel was produced through graft copolymerization with FP as a basic macromolecular skeletal material, acrylic acid as a monomer and PVA as a semi-IPNs polymer. The adsorption of ammonium and phosphate ions from aqueous solution using the new hydrogel as N and P controlled-release fertilizer with water-retention capacity was studied. The effects of pH value, concentration, contact time and ion strength on NH4+ and PO3-4 removal by FP-g-PKA/PVA semi-IPNs hydrogel were investigated using batch adsorption experiments. The results indicated that the hydrogel had high adsorption capacities and fast adsorption rates for NH4+ and PO3-4 in wide pH levels ranging from 4.0 to 9.0. Kinetic analysis presented that both NH4+ and PO3-4 removal were closely fitted with the pseudo-second-order model. Furthermore, the adsorption isotherms of hydrogel were best represented by the Freundlich model. The adsorption-desorption experimental results showed the sustainable stability of FP-g-PKA/PVA semi-IPNs hydrogel for NH4+ and PO3-4 removal. Overall, FP-g-PKA/PVA could be considered as an efficient material for the removal and recovery of nitrogen and phosphorus with the agronomic reuse as a fertilizer.

Removal of ammonium ions by laboratory-synthesized zeolite linde type A adsorption from water samples affected by mining activities in Ghana.

PubMed

Kwakye-Awuah, Bright; Labik, Linus Kweku; Nkrumah, Isaac; Williams, Craig

2014-03-01

Ammonium ion adsorption by laboratory-synthesized zeolite (linde type A; LTA) was investigated in batch kinetics experiments. Synthesized zeolite LTA was characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, thermogravimetric analysis, Fourier transform infrared spectroscopy and particle size analysis. Water samples were taken from the Nyam and Tano rivers in Ghana, and 0.8 g of zeolite was added to 100 ml portions of each sample. Portions of the samples were withdrawn every 30 min for 150 min and the concentration of ammonia in each sample was determined. The removal efficiency of zeolite LTA was evaluated by retrieving the zeolite from the water samples and adding to a fresh sample to repeat the process. Equilibrium data were fitted by Langmuir and Freundlich isotherms. Maximum adsorption capacities were 72.99 mg g(-1) for samples from the River Nyam and 72.87 mg g(-1) for samples from the River Tano. The equilibrium kinetic data were analysed using adsorption kinetic models: pseudo-first order and pseudo-second order kinetic models. Linear regression was used to estimate the adsorption and kinetic parameters. The results showed that the adsorption followed pseudo-second order kinetics and suggest that zeolite LTA is a good adsorbent for the removal of nitrogen ammonia from water.

β-Cyclodextrin grafted polypyrrole magnetic nanocomposites toward the targeted delivery and controlled release of doxorubicin

NASA Astrophysics Data System (ADS)

Hong, Shasha; Li, Zengbo; Li, Chenzhong; Dong, Chuan; Shuang, Shaomin

2018-01-01

The Fe3O4@PPy-HA-β-CD nanocomposites as the novel nanocarrier were prepared by grafting ethylenediamine derivative of​ β-​CD to the surface of polypyrrole-coated magnetic nanoparticles (Fe3O4@PPy) via using hyaluronan (HA) as the intermediate linker. HA was also the efficient target ligand for CD44. The as-prepared drug carrier was characterized by TEM, TGA, XRD, and VSM and used for the delivery of doxorubicin hydrochloride (DOX) with the high loading content of 447 mg/g. The multilayer Freundlich isotherm model was found to be a good fit for the loading of the drug carrier for DOX. Significant NIR-triggered release of DOX was observed in a weak acidic pH. And the release data in vitro was well described using the Retiger-Pepper kinetic model. Furthermore, MTT assay and confocal microscopy against Hep-G2 cells clearly illustrated that the drug carrier had no associated cytotoxicity and could easily enter the cells. The release and accumulation of DOX were observed in the cell nuclei. Thus, the DOX-loaded drug carrier killed the cancer cells efficaciously and minimized adverse side effects due to its target effect. These results suggested the as-prepared drug carrier would be of great potential for the controlled release and targeted delivery of DOX.

Coupled adsorption-photocatalytic degradation of crystal violet under sunlight using chemically synthesized grafted sodium alginate/ZnO/graphene oxide composite.

PubMed

Mohamed, S K; Hegazy, Sh H; Abdelwahab, N A; Ramadan, A M

2018-03-01

This research aimed to synthesize natural polymer nanocomposite and employ it for coupled adsorption- photocatalytic degradation of crystal violet. Sodium alginate-g-poly (acrylic acid-co-cinnamic acid) and its composites with ZnO nanorods and graphene oxide sheets were synthesized and characterized using FT-IR, XRD, SEM, HR-TEM and DR/UV-vis spectroscopy. The adsorption efficiency of samples for crystal violet has been studied in the dark. The effect of different parameters as pH, initial dye concentration, contact time and temperature on the adsorption efficiency of the synthesized sample has been examined. Kinetics studies showed that the adsorption of all samples was well described by the pseudo-second-order model and the equilibrium adsorption results fitted Freundlich model. The maximum adsorption capacity achieved at pH 5.0 was 13.85 mg g -1 . Thermodynamic studies exhibited that the adsorption is spontaneous, endothermic in nature and leads to higher entropy. Coupled adsorption-photocatalytic degradation studies under sunlight showed an enhancement in the removal efficiency by 10%. In the case of sodium alginate-g-poly (acrylic acid-co-cinnamic acid)/ZnO/graphene oxide composite, the removal efficiency after 5 h under sunlight was 94% versus 84% in the dark. Copyright © 2017 Elsevier B.V. All rights reserved.

Macrocyclic receptors immobilized to monodisperse porous polymer particles by chemical grafting and physical impregnation for strontium capture: a comparative study.

PubMed

Song, Yang; Du, Yi; Lv, Dachao; Ye, Gang; Wang, Jianchen

2014-06-15

Separation of strontium is of great significance for radioactive waste treatment and environmental remediation after nuclear accidents. In this work, a novel class of adsorbent (Crown-g-MPPPs) was synthesized by chemical grafting a macrocyclic ether receptor to monodisperse porous polymer particles (MPPPs) for strontium adsorption. Meanwhile, a counterpart material (Crown@MPPPs) with the receptor molecules immobilized to the MPPPs substrate by physical impregnation was prepared. To investigate how the immobilization manner and distribution of the receptors influence the adsorption ability, a comparative study on the adsorption behaviour of the two materials towards Sr(II) in HNO3 media was accomplished. Due to the shorter diffusion path and covalently-bonded structure, Crown-g-MPPPs showed faster adsorption kinetics and better stability for cycle use. While Crown@MPPPs had the advantages of facile synthesis and higher adsorption capacity, owing to the absence of conformational constraint to form complexation with Sr(II). Kinetic functions (Lagergren pseudo-first-order/pseudo-second-order functions) and adsorption isotherm models (Langmuir/Freundlich models) were used to fit the experimental data and examine the adsorption mechanism. On this basis, a chromatographic process was proposed by using Crown@MPPPs for an effective separation of Sr(II) (91%) in simulated high level liquid waste (HLLW). Copyright © 2014 Elsevier B.V. All rights reserved.

Functionalized chitosan electrospun nanofiber for effective removal of trace arsenate from water

PubMed Central

Min, Ling-Li; Zhong, Lu-Bin; Zheng, Yu-Ming; Liu, Qing; Yuan, Zhi-Huan; Yang, Li-Ming

2016-01-01

An environment-friendly iron functionalized chitosan elctrospun nanofiber (ICS-ENF) was synthesized for trace arsenate removal from water. The ICS-ENF was fabricated by electrospinning a mixture of chitosan, PEO and Fe3+ followed by crosslinking with ammonia vapor. The physicochemical properties of ICS-ENF were characterized by FESEM, TEM-EDX and XRD. The ICS-ENF was found to be highly effective for As(V) adsorption at neutral pH. The As(V) adsorption occurred rapidly and achieved equilibrium within 100 min, which was well fitted by pseudo-second-order kinetics model. The As(V) adsorption decreased with increased ionic strength, suggesting an outer-sphere complexation of As(V) on ICS-ENF. Freundlich model well described the adsorption isotherm, and the maximum adsorption capacity was up to 11.2 mg/g at pH 7.2. Coexisting anions of chloride and sulfate showed negligible influence on As(V) removal, but phosphate and silicate significantly reduced As(V) adsorption by competing for adsorption sites. FTIR and XPS analysis demonstrated –NH, –OH and C–O were responsible for As(V) uptake. ICS-ENF was easily regenerated using 0.003 M NaOH, and the removal rate remained above 98% after ten successively adsorption-desorption recycles. This study extends the potential applicability of electrospun nanofibers for water purification and provides a promising approach for As(V) removal from water. PMID:27572634

Modulating protein adsorption onto hydroxyapatite particles using different amino acid treatments

PubMed Central

Lee, Wing-Hin; Loo, Ching-Yee; Van, Kim Linh; Zavgorodniy, Alexander V.; Rohanizadeh, Ramin

2012-01-01

Hydroxyapatite (HA) is a material of choice for bone grafts owing to its chemical and structural similarities to the mineral phase of hard tissues. The combination of osteogenic proteins with HA materials that carry and deliver the proteins to the bone-defective areas will accelerate bone regeneration. The study investigated the treatment of HA particles with different amino acids such as serine (Ser), asparagine (Asn), aspartic acid (Asp) and arginine (Arg) to enhance the adsorption ability of HA carrier for delivering therapeutic proteins to the body. The crystallinity of HA reduced when amino acids were added during HA preparation. Depending on the types of amino acid, the specific surface area of the amino acid-functionalized HA particles varied from 105 to 149 m2 g–1. Bovine serum albumin (BSA) and lysozyme were used as model proteins for adsorption study. The protein adsorption onto the surface of amino acid-functionalized HA depended on the polarities of HA particles, whereby, compared with lysozyme, BSA demonstrated higher affinity towards positively charged Arg-HA. Alternatively, the binding affinity of lysozyme onto the negatively charged Asp-HA was higher when compared with BSA. The BSA and lysozyme adsorptions onto the amino acid-functionalized HA fitted better into the Freundlich than Langmuir model. The amino acid-functionalized HA particles that had higher protein adsorption demonstrated a lower protein-release rate. PMID:21957116

Removal of Pb(II) ions from aqueous solution by a waste mud from copper mine industry: equilibrium, kinetic and thermodynamic study.

PubMed

Ozdes, Duygu; Gundogdu, Ali; Kemer, Baris; Duran, Celal; Senturk, Hasan Basri; Soylak, Mustafa

2009-07-30

The objective of this study was to assess the adsorption potential of a waste mud (WM) for the removal of lead (Pb(II)) ions from aqueous solutions. The WM was activated with NaOH in order to increase its adsorption capacity. Adsorption studies were conducted in a batch system as a function of solution pH, contact time, initial Pb(II) concentration, activated-waste mud (a-WM) concentration, temperature, etc. Optimum pH was specified as 4.0. The adsorption kinetic studies indicated that the overall adsorption process was best described by pseudo-second-order kinetics. The equilibrium adsorption capacity of a-WM was obtained by using Langmuir and Freundlich isotherm models and both models fitted well. Adsorption capacity for Pb(II) was found to be 24.4 mg g(-1) for 10 g L(-1) of a-WM concentration. Thermodynamic parameters including the Gibbs free energy (Delta G degrees), enthalpy (Delta H degrees), and entropy (DeltaS degrees) indicated that the adsorption of Pb(II) ions on the a-WM was feasible, spontaneous and endothermic, at temperature range of 0-40 degrees C. Desorption studies were carried out successfully with diluted HCl solutions. The results indicate that a-WM can be used as an effective and no-cost adsorbent for the treatment of industrial wastewaters contaminated with Pb(II) ions.

Removal of petroleum hydrocarbons from contaminated groundwater by the combined technique of adsorption onto perlite followed by the O3/H2O2 process.

PubMed

Moussavi, Gholamreza; Bagheri, Amir

2012-09-01

Groundwater contaminated with petroleum hydrocarbons was treated using a combined system of adsorption onto powdered expanded perlite (PEP) followed by the O3/H2O2 process. The pretreatment investigations indicated a high capacity for PEP to remove petroleum hydrocarbons from the contaminated water. An experimental total petroleum hydrocarbon (TPH) adsorption capacity of 275 mg/g PEP was obtained at the natural pH of water. The experimental data fit best with the Freundlich isotherm model and pseudo-second-order adsorption model. The second phase of the experiment evaluated the performance of the O3/H2O2 process in the removal of residual TPH from pretreated water and compared the results with that of raw water. The O3/H202 process attained a maximum TPH removal rate for the pretreated water after 70 min, when 93% of the residual TPH in the effluent of the adsorption system was removed. Overall, the combination of adsorption onto PEP for 100 min and the subsequent treatment with the O3/H2O2 process for 70min eliminated over 99% of the TPH of highly petroleum-contaminated groundwater, with initial values of 162 mg/L. Therefore, we can conclude that the developed treatment system is an appropriate method of remediation for petroleum-contaminated waters.

As(III) and As(V) sorption on iron-modified non-pyrolyzed and pyrolyzed biomass from Petroselinum crispum (parsley).

PubMed

Jiménez-Cedillo, M J; Olguín, M T; Fall, C; Colin-Cruz, A

2013-03-15

The sorption of As(III) and As(V) from aqueous solutions onto iron-modified Petroselinum crispum (PCFe) and iron-modified carbonaceous material from the pyrolysis of P. crispum (PCTTFe) was investigated. The modified sorbents were characterized with scanning electron microscopy. The sorbent elemental composition was determined with energy-dispersive X-ray spectroscopy (EDS). The principal functional groups from the sorbents were determined with FT-IR. The specific surfaces and points of zero charge (pzc) of the materials were also determined. As(III) and As(V) sorption onto the modified sorbents were performed in a batch system. After the sorption process, the As content in the liquid and solid phases was determined with atomic absorption and neutron activation analyses, respectively. After the arsenic sorption processes, the desorption of Fe from PCFe and PCTTFe was verified with atomic absorption spectrometry. The morphology of PC changed after iron modification. The specific area and pzc differed significantly between the iron-modified non-pyrolyzed and pyrolyzed P. crispum. The kinetics of the arsenite and arsenate sorption processes were described with a pseudo-second-order model. The Langmuir-Freundlich model provided the isotherms with the best fit. Less than 0.02% of the Fe was desorbed from the PCFe and PCTTFe after the As(III) and As(V) sorption processes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Preparation of crosslinked chitosan magnetic membrane for cations sorption from aqueous solution.

PubMed

Khan, Adnan; Begum, Samina; Ali, Nauman; Khan, Sabir; Hussain, Sajjad; Sotomayor, Maria Del Pilar Taboada

2017-05-01

A chitosan magnetic membrane was prepared in order to confer magnetic properties to the membrane, which could be used for the removal of cations from aqueous solution. The crosslinked magnetic membrane was compared with pristine chitosan membrane in term of stability, morphology and cation adsorption capacity. The fabricated magnetic materials are thermally stable as shown by thermogravimetric curves. The membrane containing nickel magnetic particles (CHNiF-G) shows high thermal stability compared to the other membranes. The Fourier transform infrared spectroscopy showed successful preparation of chitosan magnetic membrane. Scanning electron microscopy micrographs showed the rough surface of the membrane with increased porosity. The prepared chitosan membranes were applied to cations of copper, nickel and lead in dilute aqueous solution. The chitosan membrane showed the following adsorption order for metallic cations: Cu 2+ > Ni 2+ > Pb 2+ , while CHNiF-G showed higher capacity, 3.51 mmol g -1 for copper, reflecting the improvement in adsorption capacity, since the amount of copper on pristine chitosan gave 1.40 mmol g -1 . The time required for adsorption to reach to the equilibrium was 6 h for the selected cations using different chitosan membranes. The kinetic study showed that adsorption followed pseudo-second order kinetics. The most commonly used isotherm models, Freundlich, Langmuir and Temkin, were applied to experimental data using linear regression technique. However, The Temkin model fits better to experimental data.

Sustainable approach for recycling waste lamb and chicken bones for fluoride removal from water followed by reusing fluoride-bearing waste in concrete.

PubMed

Ismail, Zainab Z; AbdelKareem, Hala N

2015-11-01

Sustainable management of waste materials is an attractive approach for modern societies. In this study, recycling of raw waste lamb and chicken bones for defluoridation of water has been estimated. The effects of several experimental parameters including contact time, pH, bone dose, fluoride initial concentration, bone grains size, agitation rate, and the effect of co-existing anions in actual samples of wastewater were studied for fluoride removal from aqueous solutions. Results indicated excellent fluoride removal efficiency up to 99.4% and 99.8% using lamb and chicken bones, respectively at fluoride initial concentration of 10 mg F/L and 120 min contact time. Maximum fluoride uptake was obtained at neutral pH range 6-7. Fluoride removal kinetic was well described by the pseudo-second order kinetic model. Both, Langmuir and Freundlich isotherm models could fit the experimental data well with correlation coefficient values >0.99 suggesting favorable conditions of the process. Furthermore, for complete sustainable management of waste bones, the resulted fluoride-bearing sludge was reused in concrete mixes to partially replace sand. Tests of the mechanical properties of fluoride sludge-modified concrete mixes indicated a potential environmentally friendly approach to dispose fluoride sludge in concrete and simultaneously enhance concrete properties. Copyright © 2015 Elsevier Ltd. All rights reserved.

Utilization of natural hematite as reactive barrier for immobilization of radionuclides from radioactive liquid waste.

PubMed

El Afifi, E M; Attallah, M F; Borai, E H

2016-01-01

Potential utilization of hematite as a natural material for immobilization of long-lived radionuclides from radioactive liquid waste was investigated. Hematite ore has been characterized by different analytical tools such as Fourier transformer infrared (FTIR), X-ray fluorescence (XRF), powder X-ray diffraction (XRD), thermogravimetry (TG) and differential thermal (DT) analysis, scanning electron microscopy (SEM) and BET-surface area. In this study, europium was used as REEs(III) and as a homolog of Am(III)-isotopes (such as (241)Am of 432.6 y, (242m)Am of 141 y and (243)Am of 7370 y). Micro particles of the hematite ore were used for treatment of radioactive waste containing (152+154)Eu(III). The results indicated that 96% (4.1 × 10(4) Bq) of (152+154)Eu(III) was efficiently retained onto hematite ore. Kinetic experiments indicated that the processes could be simulated by a pseudo-second-order model and suggested that the process may be chemisorption in nature. The applicability of Langmuir, Freundlich and Temkin models was investigated. It was found that Langmuir isotherm exhibited the best fit with the experimental results. It can be concluded that hematite is an economic and efficient reactive barrier for immobilization of long-lived radio isotopes of actinides and REEs(III). Copyright © 2015 Elsevier Ltd. All rights reserved.

Photocatalytic degradation of Orange G dye under solar light using nanocrystalline semiconductor metal oxide.

PubMed

Thennarasu, G; Kavithaa, S; Sivasamy, A

2011-08-01

The photocatalytic degradation of Orange G (OG) dye has been investigated using synthesised nanocrystalline ZnO as a photocatalyst and sunlight as the irradiation source. The formation of ZnO prepared from its precursor was confirmed through FT-IR and powder X-ray diffraction analyses. Surface morphology was characterised by scanning electron microscope and transmission electron microscope analysis. Band gap energy of synthesised nanocrystalline ZnO was calculated using diffuse reflectance spectroscopy (DRS). Different experimental parameters such as effects of pH, dye concentrations and mass of catalyst were standardised in order to achieve complete degradation of the dye molecules under solar light irradiation. The kinetics of oxidation of OG was also studied. The complete degradation of OG was evident after 90 min of irradiation at an initial pH of 6.86. The degradation of OG was confirmed by UV-Visible spectrophotometer, high-pressure liquid chromatography, ESI-Mass and chemical oxygen demand analyses. The adsorption of dye onto catalytic surface was analysed employing model equations such as Langmuir and Freundlich isotherms, and it was found that the Langmuir isotherm model best fitted the adsorption data. The solar photodegradation of OG followed pseudo-first-order kinetics. HPLC and ESI-Mass analyses of the degraded samples suggested that the dye molecules were readily degraded under solar irradiation with nanocrystalline ZnO.

Synthesis and characterization of Silica/polyvinyl imidazole/H2PO4-core-shell nanoparticles as recyclable adsorbent for efficient scavenging of Sm(III) and Dy(III) from water.

PubMed

Ettehadi Gargari, Jafar; Sid Kalal, Hossein; Shakeri, Alireza; Khanchi, Alireza

2017-11-01

In this study, we used Silica/polyvinyl imidazole core-shell nanoparticles impregnated with sodium dihydrogen phosphate (SiO 2 /PVI/H 2 PO 4 - NPs) for adsorption of samarium and dysprosium ions from aqueous solutions. The effects of the pH, adsorbent dose, contact time, and initial concentration of the adsorbate on the Core-shell nanoparticles adsorption capacity have been studied. The pH value for maximum removal of Sm (III) and Dy (III) on the core-shell nanoparticles surface were found to be 4. The saturated capacity of SiO 2 /PVI/H 2 PO 4 - NPs was up to 160mg.g -1 and 150mg.g -1 at 25°C for Sm (III) and Dy (III) ions respectively. The obtained uptake data were analyzed by the Langmuir and Freundlich equations using a linearized correlation coefficient at room temperature. The Freundlich isotherm was found to fit well with the equilibrium data. The adsorption kinetics could be modeled by a pseudo-second-order rate expression. Thermodynamic investigation revealed the adsorption process of the studied ions is entropy driven. Furthermore, the performance of regeneration and reutilization were studied. The adsorbed Sm (III) and Dy (III) can be desorbed by 0.5mol/L HCl, with the desorption percentage of 90% for Sm (III) and Dy (III). After five adsorption-desorption cycles, the adsorption capacity shows a slight decrease (about 15%), implying that the SiO 2 /PVI/H 2 PO 4 - NPs can be used as an effective adsorbent for the removal and recovery of Sm(III) and Dy(III) from aqueous solution. The colloid stability of the SiO 2 /PVI/H 2 PO 4 - NPs was investigated by dynamic light scattering measurements. The SiO 2 /PVI/H 2 PO 4 - NPs are stable in adsorption media after five adsorption - desorption cycles. The high stability of SiO 2 /PVI/H 2 PO 4 - NPs can be attributed to steric stabilization by polyvinyl imidazole adsorbed on SiO 2 nanoparticle surfaces. Copyright © 2017 Elsevier Inc. All rights reserved.

Soils impacted by PAHs: Would the stabilized organic matter be a green tool for the immobilization of these noxious compounds?

PubMed

Dores-Silva, Paulo R; Cotta, Jussara A O; Landgraf, Maria D; Rezende, Maria O O

2018-05-04

The objective of this study was to investigate the role of stabilized organic matter (vermicompost) and tropical soils in the sorption of naphthalene, anthracene and benzo[a]pyrene. The results obtained for the three compounds were extrapolated for the priority polycyclic aromatic hydrocarbons (PAHs) pollutants according to Environmental Protection Agency (US EPA). To evaluate the sorption process, high performance liquid chromatography was employed and the data was fitted by Freundlich isotherms. The results suggest that the sorption effect generally increases with the number of benzene rings of the PAHs, and that the persistence of PAHs in the environment is possibly related to the number of benzene rings in the PAH molecule. In addition, the pH of the vermicompost can strongly affect the adsorption process in this matrix.

Capacity and mechanisms of ammonium and cadmium sorption on different wetland-plant derived biochars.

PubMed

Cui, Xiaoqiang; Hao, Hulin; Zhang, Changkuan; He, Zhenli; Yang, Xiaoe

2016-01-01

The objective of this study was to investigate the relationship between Cd(2+)/NH4(+) sorption and physicochemical properties of biochars produced from different wetland plants. Biochars from six species of wetland plants (i.e., Canna indica, Pennisetum purpureum Schum, Thalia dealbata, Zizania caduciflora, Phragmites australis and Vetiveria zizanioides) were obtained at 500°C and characterized, and their sorption for ammonium and cadmium was determined. There were significant differences in elemental composition, functional groups and specific surface area among the biochars derived from different wetland plant species. Sorption of ammonium and cadmium on the biochars could be described by a pseudo second order kinetic model, and the simple Langmuir model fits the isotherm data better than the Freundlich or Temkin model. The C. indica derived biochar had the largest sorption capacity for NH4(+) and Cd(2+), with a maximum sorption of 13.35 and 125.8mgg(-1), respectively. P. purpureum Schum derived biochar had a similar maximum sorption (119.3mgg(-1)) for Cd(2+). Ammonium sorption was mainly controlled by cation exchange, surface complexation with oxygen-containing functional groups and the formation of magnesium ammonium phosphate compounds, whereas for Cd(2+) sorption, the formation of cadmium phosphate precipitates, cation exchange and binding to oxygen-containing groups were the major possible mechanisms. In addition, the sorption of ammonium and cadmium was not affected by surface area and microporosity of the biochars. Copyright © 2015 Elsevier B.V. All rights reserved.

Removal of Crystal Violet by Using Reduced-Graphene-Oxide-Supported Bimetallic Fe/Ni Nanoparticles (rGO/Fe/Ni): Application of Artificial Intelligence Modeling for the Optimization Process

PubMed Central

Ruan, Wenqian; Qi, Jimei; Hou, Yu; Cao, Rensheng; Wei, Xionghui

2018-01-01

Reduced-graphene-oxide-supported bimetallic Fe/Ni nanoparticles were synthesized in this study for the removal of crystal violet (CV) dye from aqueous solutions. This material was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS), Raman spectroscopy, N2-sorption, and X-ray photoelectron spectroscopy (XPS). The influence of independent parameters (namely, initial dye concentration, initial pH, contact time, and temperature) on the removal efficiency were investigated via Box–Behnken design (BBD). Artificial intelligence (i.e., artificial neural network, genetic algorithm, and particle swarm optimization) was used to optimize and predict the optimum conditions and obtain the maximum removal efficiency. The zero point of charge (pHZPC) of rGO/Fe/Ni composites was determined by using the salt addition method. The experimental equilibrium data were fitted well to the Freundlich model for the evaluation of the actual behavior of CV adsorption, and the maximum adsorption capacity was estimated as 2000.00 mg/g. The kinetic study discloses that the adsorption processes can be satisfactorily described by the pseudo-second-order model. The values of Gibbs free energy change (ΔG0), entropy change (ΔS0), and enthalpy change (ΔH0) demonstrate the spontaneous and endothermic nature of the adsorption of CV onto rGO/Fe/Ni composites. PMID:29789483

Equilibrium isotherms, kinetics, and thermodynamics studies for congo red adsorption using calcium alginate beads impregnated with nano-goethite.

PubMed

Munagapati, Venkata Subbaiah; Kim, Dong-Su

2017-07-01

The present study is concerned with the batch adsorption of congo red (CR) from an aqueous solution using calcium alginate beads impregnated with nano-goethite (CABI nano-goethite) as an adsorbent. The optimum conditions for CR removal were determined by studying operational variables viz. pH, adsorbent dose, contact time, initial dye ion concentration and temperature. The CABI nano-goethite was characterized by Fourier transform infrared spectroscopy (FTIR), X- ray diffraction (XRD) and Scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS) analysis. The CR sorption data onto CABI nano-goethite were described using Langmuir, Freundlich, Dubinin-Radushkevich and Temkin isotherm models. The results show that the best fit was achieved with the Langmuir isotherm model. The maximum adsorption capacity (181.1mg/g) of CR was occurred at pH 3.0. Kinetic studies showed that the adsorption followed a pseudo-second-order model. Desorption experiments were carried out to explore the feasibility of regenerating the adsorbent and the adsorbed CR from CABI nano-goethite. The best desorbing agent was 0.1M NaOH with an efficiency of 94% recovery. The thermodynamic parameters ΔG°, ΔH°, and ΔS° for the CR adsorption were determined by using adsorption capacities at five different temperatures (293, 303, 313, 323 and 303K). Results show that the adsorption process was endothermic and favoured at high temperature. Copyright © 2017 Elsevier Inc. All rights reserved.

A potential low cost adsorbent for the removal of cationic dyes from aqueous solutions

NASA Astrophysics Data System (ADS)

Uddin, Md. Tamez; Rahman, Md. Arifur; Rukanuzzaman, Md.; Islam, Md. Akhtarul

2017-10-01

This study was aimed at using mango leaf powder (MLP) as a potential adsorbent for the removal of methylene blue (MB) from aqueous solutions. Characterization of the adsorbent was carried out with scanning electron microscopy, Fourier transform infrared spectroscopy, and nitrogen adsorption-desorption analysis. The pH at the point of zero charge of the adsorbent was determined by titration method and was found a value to be 5.6 ± 0.2. Batch studies were performed to evaluate the influence of various experimental parameters like initial solution pH, contact time, initial concentration of dye and adsorbent dosage on the removal of MB. An adsorption-desorption study was carried out resulting the mechanism of adsorption was carried out by electrostatic force of attraction. The adsorption equilibrium time required for the adsorption of MB on MLP was almost 2 h and 85 ± 5% of the total amount of dye uptake was found to occur in the first rapid phase (30 min). The Langmuir and Freundlich isotherm models were used for modeling the adsorption equilibrium. The experimental equilibrium data could be well interpreted by Langmuir isotherm with maximum adsorption capacity of 156 mg/g. To state the sorption kinetics, the fits of pseudo-first-order and pseudo-second-order kinetic models were investigated. It was obtained that the adsorption process followed the pseudo-second-order rate kinetics. The above findings suggest that MLP can be effectively used for decontamination of dye containing wastewater.

Fabrication of carbon/SiO2 composites from the hydrothermal carbonization process of polysaccharide and their adsorption performance.

PubMed

Li, Yinhui; Li, Kunyu; Su, Min; Ren, Yanmei; Li, Ying; Chen, Jianxin; Li, Liang

2016-11-20

In this work, carbon/SiO2 composites, using amylose and tetraethyl orthosilicate (TEOS) as raw materials, were successfully prepared by a facial hydrothermal carbonization process. The carbon/SiO2 composites were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), Energy Dispersive Spectroscopy (EDS), transmission electron microscope (TEM), N2 adsorption and Thermogravimetric (TG) analysis. The composites, which were made up of amorphous SiO2 and amorphous carbon, were found to have hierarchical porous structures. The mass ratios of amylose and SiO2 and the hydrothermal carbonization time had significant effects on the morphology of the composites, which had three shapes including monodispersed spheres, porous pieces and the nano-fibers combined with nano-spheres structures. The adsorption performance of the composites was studied using Pb(2+) as simulated contaminants from water. When the mass ratio of amylose and SiO2 was 9/1, the hydrothermal time was 30h and the hydrothermal temperature was 180°C, the adsorption capacity of the composites achieved to 52mg/g. Experimental data show that adsorption kinetics of the carbon/SiO2 composites can be fitted well by the Elovich model, while the isothermal data can be perfectly described by the Langmuir adsorption model and Freundlich adsorption model. The maximum adsorption capacity of the carbon/SiO2 composites is 56.18mgg(-1). Copyright © 2016 Elsevier Ltd. All rights reserved.

Synthesis and crystal structure of Cd-based metal-organic framework for removal of methyl-orange from aqueous solution

NASA Astrophysics Data System (ADS)

Tella, Adedibu C.; Olawale, Margaret D.; Neuburger, Markus; Obaleye, Joshua A.

2017-11-01

A novel [Cd(INA)2(H2O)]. ISB (1) (INA = isonicotinate; ISB = isobutanol) was synthesized through the reaction between the isonicotinic acid ligand and cadmium (II) salt and characterized by elemental analysis, FTIR and UV-Visible spectroscopies, SEM and Single crystal X-ray diffraction. The crystal is orthorhombic, space group Pbca, a = 12.24(10) Å, b = 15.4646(13) Å, c = 18.8445(17) Å, V = 3569(3) Å3, Z = 8. The pentagonal bipyramid (seven coordinate) around the cadmium (II) ion is of the form CdN2O5 coordinating to four oxygen atoms from carboxylates, one oxygen atom from water molecule and two nitrogen atoms of pyridine. The structure of compound is stabilized by two hydrogen bonds namely intermolecular (O-H-O) and intramolecular type C-H-O accounting for polymeric nature of the metal-organic frameworks. 1 was studied for adsorptive removal of methyl orange (MO) from aqueous solution. Equilibrium isotherm study reveals that Langmuir model gave a better fitting result than the Freundlich model. The pseudo-second order model could be used to interpret adsorption kinetics. The maximum adsorption capacity calculated by Langmuir was 166 mg/g at 300 K. These results indicate the adsorption of MO on 1 is partly due to electrostatic interaction between methyl orange and the adsorbent. 1 could be used as adsorbent to remove methyl orange from aqueous solution.