Insensitive fuze train for high explosives

DOEpatents

Cutting, Jack L.; Lee, Ronald S.; Von Holle, William G.

1994-01-01

A generic insensitive fuze train to initiate insensitive high explosives, such as PBXW-124. The insensitive fuze train uses a slapper foil to initiate sub-gram quantities of an explosive, such as HNS-IV or PETN. This small amount of explosive drives a larger metal slapper onto a booster charge of an insensitive explosive, such as UF-TATB. The booster charge initiates a larger charge of an explosive, such as LX-17, which in turn, initiates the insensitive high explosive, such as PBXW-124.

Insensitive fuze train for high explosives

DOEpatents

Cutting, J.L.; Lee, R.S.; Von Holle, W.G.

1994-01-04

A generic insensitive fuze train to initiate insensitive high explosives, such as PBXW-124 is described. The insensitive fuze train uses a slapper foil to initiate sub-gram quantities of an explosive, such as HNS-IV or PETN. This small amount of explosive drives a larger metal slapper onto a booster charge of an insensitive explosive, such as UF-TATB. The booster charge initiates a larger charge of an explosive, such as LX-17, which in turn, initiates the insensitive high explosive, such as PBXW-124. 3 figures.

Development of Simulation Techniques for the M739 and M577 Fuzes

DTIC Science & Technology

1984-04-01

AD-E401 166 CONTRACTOR RWRRT ARLCD-CR-84003 DEVELOPMENT OF SIMUILATION TECNQUES? FOR THE M739 , AND ýM577 FUZES GERARD G. LOWEN nvN-,qMA’qCSASSOCIAT04...DEVELOPMENT OF SIMULATION TECHNIQUES FOR THE M739 Final AND M4577 FUZES May 1982 - December 1983 6. PERFORMING ORO. REPORT NUMBER 7. AUTNOR(a) SI. CONTRACT...2 Variation of Escapement Center Distance on Number of Turns-to-Arm of the M739 S&A Mathematical Models of Clock Gear Train S&A 3 Forward Kinematics

Operation Sun Beam, Shot Small Boy. Project Officer's report - Project 7. 8. Arming and fuzing component test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taslitt, N.

1985-09-01

The objectives of this project were to (1) determine whether the radiation from a nuclear weapon can disable various arming and fuzing components by causing permanent damage; (2) determine whether transient nuclear radiation can induce an operating fuze to malfunction; and (3) compare nuclear weapon radiation effects with those produced by various radiation simulators. Data obtained revealed that none of the inertial components were detrimentally affected. The electronic components were severely degraded but would have satisfactorily accomplished their tactical functions. No electromagnetic effects were detected.

Overview of the Fusion Z-Pinch Experiment FuZE

NASA Astrophysics Data System (ADS)

Weber, T. R.; Shumlak, U.; Nelson, B. A.; Golingo, R. P.; Claveau, E. L.; McLean, H. S.; Tummel, K. K.; Higginson, D. P.; Schmidt, A. E.; UW/LLNL Team

2016-10-01

Previously, the ZaP device, at the University of Washington, demonstrated sheared flow stabilized (SFS) Z-pinch plasmas. Instabilities that have historically plagued Z-pinch plasma confinement were mitigated using sheared flows generated from a coaxial plasma gun of the Marshall type. Based on these results, a new SFS Z-pinch experiment, the Fusion Z-pinch Experiment (FuZE), has been constructed. FuZE is designed to investigate the scaling of SFS Z-pinch plasmas towards fusion conditions. The experiment will be supported by high fidelity physics modeling using kinetic and fluid simulations. Initial plans are in place for a pulsed fusion reactor following the results of FuZE. Notably, the design relies on proven commercial technologies, including a modest discharge current (1.5 MA) and voltage (40 kV), and liquid metal electrodes. Supported by DoE FES, NNSA, and ARPA-E ALPHA.

Shock sensing dual mode warhead

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shamblen, M.; Walchak, M.T.; Richmond, L.

1980-12-31

A shock sensing dual mode warhead is provided for use against both soft and hard targets and is capable of sensing which type of target has been struck. The warhead comprises a casing made of a ductile material containing an explosive charge and a fuze assembly. The ductile warhead casing will mushroom upon striking a hard target while still confining the explosive. Proper ductility and confinement are necessary for fuze shock sensing. The fuze assembly contains a pair of parallel firing trains, one initiated only by dynamic pressure caused high impact deceleration and one initiated by low impact deceleration. Themore » firing train actuated by high impact deceleration senses dynamic pressure transmitted, during deformation of the warhead, through the explosive filler which is employed as a fuzing signature. The firing train actuated by low impact deceleration contains a pyrotechnic delay to allow penetration of soft targets.« less

Design of diode-pumped solid-state laser applied in laser fuses

NASA Astrophysics Data System (ADS)

Deng, FangLin; Zhang, YiFei

2005-04-01

The function of laser fuzes which are parts of certain weapon systems is to control the blasting height of warheads. Commonly the battle environment these weapon systems are confronted with is very complicated and the tactical demand for them is very rigor, so laser fuzes equipped for them must fulfill some special technical requirements, such as high repetition rate, long ranging scope, etc. Lasers are one of key components which constitute fuze systems. Whether designed lasers are advanced and reasonable will determine whether laser fuzes can be applied in these weapon systems or not. So we adopt the novel technology of diode-pumped solid-state laser (DPSSL) to design lasers applied in fuzes. Nd:YVO4 crystal is accepted as gain material, which has wide absorption band and large absorption efficient for 808nm pumping laser. As warhead's temperature is usually very high, wider absorption band is beneficial to reduce the influence of temperature fluctuation. Passive Q-switching with Cr4+:YAG is used to reduce the power consumption farthest. Design the end-pumped microchip sandwich-architecture to decrease lasers' size and increase the reliability, further it's advantageous to produce short pulses and increase peak power of lasers. The designed DPSSL features small size and weight, high repetition rate and peak power, robustness, etc. The repetition rate is expected to reach 1 kHz; peak power will exceed 300 kW; pulse width is only 5 ns; and divergence angle of laser beams is less than 5 mrad. So DPSSL is suitable for laser fuzes as an emitter.

Properties of Ti-6Al-4V spun formed fuze supports

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moody, N.R.; Gates, G.

1985-05-01

Spin forming is designated as the primary fabrication process for the Ti-6A1-4V, W-87 fuze support. This process reduces the amount of rough machining during production, the cost of the starting material and the lead time from order to delivery of finished parts compared with parts made from forgings. However, because the amount of deformation from the spin forming process varies greatly within the part, the properties resulting from spin forming the fuze supports are unknown. This study shows that the properties and microstructure of the highly deformed walls of the fuze support are similar to those of forgings, while themore » properties and microstructure of the lightly deformed nose are similar to those of the parent plate. A solution treatment at 1750/sup 0/F/1h/WQ (954/sup 0/C) followed by a 900/sup 0/F (482/sup 0/C) four hour age gives the desired properties. Additionally, microstructural evaluation shows that the temperatures during spin forming are maintained within desired limits and that no significant microstructural changes occur during subsequent elevated temperature processing of the finished part. This study shows that solution treated and aged parts meet all required properties for all conditions to which the fuze supports will be subjected.« less

Comparison of Explosives Residues from the Blow-in-Place Detonation of 155-mm High-Explosive Projectiles

DTIC Science & Technology

2006-06-01

were M107 high-explosive deep-cavity 155-mm howitzer projectiles with a supplemental charge and an M739 point- detonating fuze mounted in the nose...M107, HE, w/o fuze IOP03E100-011 14 1390010809447 N340 Fuze, point-detonating, M739 MA-84B007-013 14 1375014151232 ML47 Cap, blasting, non-electric 30... M739 N340 0 21 0 ə Cap, blasting, M11 ML47 ə 27 ə ə Cap, blasting, M13 MN03 0 ə 0 ə Cap, blasting, M14 MN06 0 0 0 ə Cord, detonating M456 0

Dual mode warhead

DOE Office of Scientific and Technical Information (OSTI.GOV)

Obrsky, J.; Alexander, A.A.; Griffen, O.H.

1980-12-31

A dual mode warhead is provided for use against both soft and hard targets and capable of sensing which type of target has been struck comprising a casing made of a ductile material containing an explosive charge and a fuze assembly. The ductile warhead casing will mushroom and later split upon striking a hard target while still confining the explosive. Proper ductility and confinement are necessary for fuze sensing. The fuze assembly contains a pair of parallel firing trains, one initiated only by high and one by low impact deceleration. The firing train actuated by low impact deceleration contains amore » pyrotechnic delay to allow penetration of soft targets.« less

Development of thermocouple generators for small-caliber munitions fuze. Phase I. Final report, 1 Feb--3 Sep 1974. [Aerodynamically heated thermoelectric converters to power rf proximity fuses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eggers, P.E.

1975-03-01

An analytical study has been performed to assess the feasibility of using aerodynamically heated thermoelectric convertors to power RF proximity fuzes. The collective results of this study indicate that such a thermoelectric power supply is feasible for use with 20 mm projectiles and is compatible with the existing RF fuze circuit and safe arming distance requirements. A disc module concept has evolved from this study involving thin-film bismuth telluride as the basic thermoelectric element. Preliminary experimental studies were completed in order to identify principal parameters for the bismuth telluride.

Accuracy Improvement Capability of Advanced Projectile Based on Course Correction Fuze Concept

PubMed Central

Elsaadany, Ahmed; Wen-jun, Yi

2014-01-01

Improvement in terminal accuracy is an important objective for future artillery projectiles. Generally it is often associated with range extension. Various concepts and modifications are proposed to correct the range and drift of artillery projectile like course correction fuze. The course correction fuze concepts could provide an attractive and cost-effective solution for munitions accuracy improvement. In this paper, the trajectory correction has been obtained using two kinds of course correction modules, one is devoted to range correction (drag ring brake) and the second is devoted to drift correction (canard based-correction fuze). The course correction modules have been characterized by aerodynamic computations and flight dynamic investigations in order to analyze the effects on deflection of the projectile aerodynamic parameters. The simulation results show that the impact accuracy of a conventional projectile using these course correction modules can be improved. The drag ring brake is found to be highly capable for range correction. The deploying of the drag brake in early stage of trajectory results in large range correction. The correction occasion time can be predefined depending on required correction of range. On the other hand, the canard based-correction fuze is found to have a higher effect on the projectile drift by modifying its roll rate. In addition, the canard extension induces a high-frequency incidence angle as canards reciprocate at the roll motion. PMID:25097873

Accuracy improvement capability of advanced projectile based on course correction fuze concept.

PubMed

Elsaadany, Ahmed; Wen-jun, Yi

2014-01-01

Improvement in terminal accuracy is an important objective for future artillery projectiles. Generally it is often associated with range extension. Various concepts and modifications are proposed to correct the range and drift of artillery projectile like course correction fuze. The course correction fuze concepts could provide an attractive and cost-effective solution for munitions accuracy improvement. In this paper, the trajectory correction has been obtained using two kinds of course correction modules, one is devoted to range correction (drag ring brake) and the second is devoted to drift correction (canard based-correction fuze). The course correction modules have been characterized by aerodynamic computations and flight dynamic investigations in order to analyze the effects on deflection of the projectile aerodynamic parameters. The simulation results show that the impact accuracy of a conventional projectile using these course correction modules can be improved. The drag ring brake is found to be highly capable for range correction. The deploying of the drag brake in early stage of trajectory results in large range correction. The correction occasion time can be predefined depending on required correction of range. On the other hand, the canard based-correction fuze is found to have a higher effect on the projectile drift by modifying its roll rate. In addition, the canard extension induces a high-frequency incidence angle as canards reciprocate at the roll motion.

Analysis of base fuze functioning of HESH ammunitions through high-speed photographic technique

NASA Astrophysics Data System (ADS)

Biswal, T. K.

2007-01-01

High-speed photography plays a major role in a Test Range where the direct access is possible through imaging in order to understand a dynamic process thoroughly and both qualitative and quantitative data are obtained thereafter through image processing and analysis. In one of the trials it was difficult to understand the performance of HESH ammunitions on rolled homogeneous armour. There was no consistency in scab formation even though all other parameters like propellant charge mass, charge temperature, impact velocity etc are maintained constant. To understand the event thoroughly high-speed photography was deployed to have a frontal view of the total process. Clear information of shell impact, embedding of HE propellant on armour and base fuze initiation are obtained. In case of scab forming rounds these three processes are clearly observed in sequence. However in non-scab ones base fuze is initiated before the completion of the embedding process resulting non-availability of threshold thrust on to the armour to cause scab. This has been revealed in two rounds where there was a failure of scab formation. As a quantitative measure, fuze delay was calculated for each round and there after premature functioning of base fuze was ascertained in case of non-scab rounds. Such potency of high-speed photography has been depicted in details in this paper.

Mini-Warriors: Microelectromechanical Systems: A Munitions Revolution

DTIC Science & Technology

2014-02-01

hand-held con- troller senses and transmits body movements to the video game—much like the Lycra suit with 85 MEMS, worn by ac- tors, which aided...for the anti-torpedo tor- pedo . Although it uses a macro-size fuze, significantly reduced in size by the Division, its experimental MEMS fuze informed

Failure analysis of fuze power supply

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menke, J.T.

1996-10-01

Batteries in storage which were used in electronic fuzes were found to be leaking after 5 years. The leaking battery ampules were made of copper and contained mixture of fluoboric acid and methylene bromide. The corrosion mechanism is described along with the testing/analysis required to simulate the field failures.

Inertial Impact Switches for Artillery Fuzes. Part III. Rocket Application

DTIC Science & Technology

1975-04-01

INtWT.INiUUITO» iiTwar mN.coimcT Nom > i. minrtwotMutt. SLOTS IN END UP MO SCOVTOBCmUNC«ITH EMM OTMR WITHIN 10* SCCNOTC...ENGR LAB COMMANDER NAVAL SURFACE WEAPONS CENTER WHITE OAK, MD 20910 ATTN CODE 043 , PROJ MGR, FUZES ATTN CODE 511, ATTN CODE 512, ATTN CODE 522

Rain Premature Susceptibility Study on the Proposed Piezoelectric Contact Fuze System for Triggering the MC-132 in the TX-5X1 Weapon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wehrle, R.D.

1953-06-18

The probability of the occurrence of rain during the "armed" portion of the fall of a bomb is approximately 1/25. Therefore, rain is considered a problem in premature detonation of the warhead through activation of the contact fuze system.

MC3196 Detonator Shipping Package Hazard Classification Assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones; Robert B.

1979-05-31

An investigation was made to determine whether the MC3196 detonator should be assigned a DOT hazard classification of Detonating Fuze, Class C Explosives per 49 CFR 173.113. This study covers the Propagation Test and the External Heat Test as approved by DOE Albuquerque Operations Office. Test data led to the recommeded hazard classification of detonating fuze, Class C explosives.

Assessment of the MC3608 detonator shipping package hazard classification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, R.B.

1981-08-07

An investigation was made to determine whether the MC 3608 Detonator should be assigned a DOT hazard classification of Detonating Fuze, Class C Explosive, per 49 CFR 173.113. This study covers the propagation test as approved by DOE-Albuquerque Operations Office. Analysis of the test data led to the recommended hazard classification of Detonating Fuze, Class C Explosive.

77 FR 77040 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-31

... Laser Guided Bombs, 162 FMU-152 bomb fuzes, 150 BLU-111B/B 500-lb Conical Fin General Purpose Bombs (Freefall Tail), 60 BLU-111B/B 500-lb Retarded Fin General Purpose Bombs (Ballute Tail), and 32 CBU-105 Wind... (AMRAAM), 162 GBU-12 PAVEWAY II 500-lb Laser Guided Bombs, 162 FMU-152 bomb fuzes, 150 BLU- 111B/B 500-lb...

Energetic Residues from Blow-in-Place Detonation of 60-mm and 120-mm Fuzed High-Explosive Mortar Cartridges

DTIC Science & Technology

2008-10-01

ER D C/ CR R EL T R -0 8 -1 9 Energetic Residues from Blow-in-Place Detonation of 60-mm and 120-mm Fuzed High-Explosive Mortar Cartridges...Figure 4. Sample filtration setup. ............................................................................................................. 8 ...15 Table 8 . HE munitions BIP and live-fire detonation energetics residues data. .................................. 17 ERDC/CRREL TR-08

Ground-echo characteristics for a ground-target pulse-Doppler radar fuze of high duty ratio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, C.S.

1973-11-21

From Tri-service electronic fuse symposium; Washington, District of Columbia, USA (26 Nov 1973). A pulse-Doppler radar fuze for use against ground targets at high burst heights can operate at low peak power provided a high duty ratio is used. The high duty ratio brings about ambiguous ground return that is prevented from firing the fuze by randomly coding the phase of the transmitted pulses. This causes the ambiguous return to appear as random noise. This paper provides formulas for the calculation of the clutter-noise power density and of the signal power so that the performance of the radar can bemore » determined. The paper also discusses the myth of decorrelation'' that is alleged to destroy the transmittedphase modulation in the echo and so make it useless. (auth)« less

Weapons Systems, United States Army 1997.

DTIC Science & Technology

1997-01-01

fewer grenades, a new warhead section fuze and a modified center core burster. The XM85 grenade is equipped with a new self -destruct fuze designed to...Liquid Propellant Gun and an automated loading system. Crusader also requires 3 fewer crewmen than previous self -propelled artillery systems. The new ...market, creating new market opportunities for commercial rotocraft and ensuring the continued supremacy of this technol- ogy that is so critical to

Impact Sensors for Use with Electronic Fuzes

DTIC Science & Technology

1975-12-01

corroborated the major features of a theoretical analysis. More work is needed to 10R. Wasser , Impact Switch Tests, US Naval Ordnance...might be more fruitful if more effort were expended on electro- mechanical systems. One principle that could be applied to such a l0R. Wasser ...Switches for Artillery Fuzes, Part I: Development, Harry Diamond Laboratories TM-72-18 (July 1972). (10) R. Wasser , Impact Switch TestP, US Naval

Bearing Survivability and Friction Determination for Fuze Decoupling Applications

DTIC Science & Technology

2012-09-01

three types of ball bearings. The revolutions per minute versus time plots acquired from spin-down trials provide a qualitative view of bearing...ACKNOWLEDGMENTS The Dragon Bearing Team would like to thank Jason DeVenezia and Michael Hollis for their assistance in developing test fixtures...Optimized Navigation ( DRAGON ) program, the bearings would be used to decouple the fuze from the remainder of the body to mitigate drive actuation

Modified M505A3 Fuze with Delay Function

DTIC Science & Technology

1974-10-01

forward initiation on the firing pin entrance hole to the rotor cavity. The triple staked detonator also functioned on the 0.063-inch target at 75... effectiveness of this projectile against aircraft targets by Incorporating a time delay which enables the projectile to penetrate the aircraft skin...prior to detonation. This effort required the design of modifications to the M505A3 fuze to achieve a delay function without modifying the rotor

Enhanced Electromagnetic Tagging for Embedded Tracking of Munitions and Ordnance During Future Remediation Efforts. Revision 2

DTIC Science & Technology

2007-06-01

study), so tags placed in the fuze will allow both munitions to be tagged. • Fuze modification : o Four equally spaced grooves, 0.32 inches deep...investigation. Therefore, effort must continue to verify all recommendations before implementing the modifications . The list below highlights critical...concerns that require attention and verification: • Environmental o Manufacturing modifications to attach the tag Worker safety Bio friendliness o

Handbook of Ballistic and Engineering Data for Ammunition. Volume 1. 20-1-95 to 75-1-310 Included

DTIC Science & Technology

1950-07-01

steel uistead of cast iron)witb the PD Fuze M52 as standard for limited procurement. OCM items 16026 and 16122 recommended and approved standardization of...BALLSTIC AND ENGINEERIN DATA II DRAG~E75 COFFCINT MACH NUMBER PLDT -14 44 SHELLI H5-mM .. a; FUZE,CPD, 7PI SEL;HEL, 75-MM M48; UE,TJ 3 fill 1.5 I . 2I

Development of an automated fuzing station for the future armored resupply vehicle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chesser, J.B.; Jansen, J.F.; Lloyd, P.D.

1995-03-01

The US Army is developing the Advanced Field Artillery System (SGSD), a next generation armored howitzer. The Future Armored Resupply Vehicle (FARV) will be its companion ammunition resupply vehicle. The FARV with automate the supply of ammunition and fuel to the AFAS which will increase capabilities over the current system. One of the functions being considered for automation is ammunition processing. Oak Ridge National Laboratory is developing equipment to demonstrate automated ammunition processing. One of the key operations to be automated is fuzing. The projectiles are initially unfuzed, and a fuze must be inserted and threaded into the projectile asmore » part of the processing. A constraint on the design solution is that the ammunition cannot be modified to simplify automation. The problem was analyzed to determine the alignment requirements. Using the results of the analysis, ORNL designed, built, and tested a test stand to verify the selected design solution.« less

Overview of the FuZE Fusion Z-Pinch Experiment

NASA Astrophysics Data System (ADS)

Shumlak, U.; Nelson, B. A.; Claveau, E. L.; Forbes, E. G.; Golingo, R. P.; Stepanov, A. D.; Weber, T. R.; Zhang, Y.; McLean, H. S.; Higginson, D. P.; Schmidt, A.; Tummel, K. K.

2017-10-01

Successful results of the sheared flow stabilized (SFS) Z-pinch from ZaP and ZaP-HD have motivated the new FuZE project to scale the plasma performance to fusion conditions. The SFS Z-pinch is immune to the instabilities that plague the conventional Z-pinch yet maintains the same favorable radial scaling. The plasma density and temperature increase rapidly with decreasing plasma radius, which naturally leads to a compact configuration at fusion conditions. The SFS Z-pinch is being investigated as a novel approach to a compact fusion device in a collaborative ARPA-E ALPHA project with the University of Washington and Lawrence Livermore National Laboratory. The project includes an experimental effort coupled with high-fidelity physics modeling using kinetic and fluid simulations. Along with scaling law analysis, computational and experimental results from the FuZE device are presented. This work is supported by an award from US ARPA-E.

Common Low-cost IM Explosive Program. Development of Next Generation Insensitive Munitions: A Success Story

DTIC Science & Technology

2011-11-30

fuze separating from the shell body preventing high order detonations thus saving the lives of the Soldiers. Unit’s SPC Alan Ng  with his father Peter...Sensitive If not fully compliant, must show improvement over Baseline explosive Affordable Artillery Cost Drivers = Steel Body Material & Explosive Fill...Mortar Cost Drivers = Steel Body Material, Fuze & Propelling Charges Producible within the National Technology and Industrial Base Infrastructure

Multiple Launch Rocket System (MLRS) Fuze.

DTIC Science & Technology

1982-06-18

8217This is to be expected, since the probes are near the axis of symmetry 08 (where the bow shock wave is most nearly normal) and, being Pitot probes ...that simulated altitudes from 15.2 Km to 21 Km. The fuze ogive was instrumented with both static and pitot pressure probes , from which the pressure data...insights into the flow. Because the bow shock wave is curved, the static-pressure on the-- .urface should decrease from avalue__ of the stagnation pressure

Producing High-Performance, Stable, Sheared-Flow Z-Pinches in the FuZE project

NASA Astrophysics Data System (ADS)

Golingo, R. P.; Shumlak, U.,; Nelson, B. A.; Claveau, E. L.; Forbes, E. G.; Stepanov, A. D.; Weber, T. R.; Zhang, Y.; McLean, H. S.; Tummel, K. K.; Higginson, D. P.; Schmidt, A. E.; University of Washington (UW) Collaboration; Lawrence Livermore National Laboratory (LLNL) Collaboration

2017-10-01

The Fusion Z-Pinch Experiment (FuZE) has made significant strides towards generating high-performance, stable Z-pinch plasmas with goals of ne = 1018 cm-3 and T =1 keV. The Z-pinch plasmas are stabilized with a sheared axial flow that is driven by a coaxial accelerator. The new FuZE device has been constructed and reproduces the major scientific achievements the ZaP project at the University of Washington; ne = 1016 cm-3,T = 100 eV, r<1 cm, and tstable >20 μs. These parameters are measured with an array of magnetic field probes, spectroscopy, and fast framing cameras. The plasma parameters are achieved using a small fraction of the maximum energy storage and gas injection capability of the FuZE device. Higher density, ne = 5×1017 cm-3, and temperature, T = 500 eV, Z-pinch plasmas are formed by increasing the pinch current. At the higher voltages and currents, the ionization rates in the accelerator increase. By modifying the neutral gas profile in the accelerator, the plasma flow from the accelerator is maintained, driving the flow shear. Formation and sustainment of the sheared-flow Z-pinch plasma will be discussed. Experimental data demonstrating high performance plasmas in a stable Z-pinches will be shown. This work is supported by an award from US ARPA-E.

Computer Simulation of Artillery S&A Mechanism (Involute Gear Train and Straight-Sided Verge Runaway Escapement)

DTIC Science & Technology

1982-11-01

Report) IS. SUPPLEMENTARY NOTES It. KEY WORDS (Contin~ue an reverse aide It neoocemry and Identity by block number) Gear train S&A mechanism M739 fuze...as in the escapement. A simulation run with the dimensions of the M739 safing and arming mechanism showed excellent agreament with experimental...well as all non-impact contact forces. This program was extensively tested for the configuration no. 2 data (fig. 2) of the M739 fuze S&A mechanism

Exploratory Development on an Electronic Safing and Arming Device for Ordnance Fuzing

DTIC Science & Technology

1983-02-01

to the bridges. Two units were subjected to MIL-STD-331, Test 101, Jolt. The EBMs were placed in the S & A cavity of an M739 fuze body for this test...of the program was to explore a concept for a safe, reliable, general purpose, low cost, electronic, A ’ zsafing and arming ( S & A ) system for use in...breadboard model hardware of the electronic S & A device. The electronic S & A devicu consists of an explosive barrier moduls (EBM) explosive train

Report of Hero Board: Proceedings of the Board of Officers Convened by the Following Order, General Headquarters, American Expeditionary Forces, Office, Chief of Artillery

DTIC Science & Technology

1985-01-01

brigade to battery inclusive. Interchangeability of all dry cells for all F. A. equipment. Kinds of projectiles fuzes and charges in use at...Battery, inclusive. Interchangeability of all dry cells used for all Field Artillery equipment. Kinds of projectiles and fuzes in use at present...obtaining horses of sufficient stamins and in sufficient numbers to properly handle the ammunition supply during combat, together with the serious

Fuze Experimentation Facility and Fuze Industrial Facility (FEF/FIF) Construction. Final Environmental Assessment

DTIC Science & Technology

2011-04-01

1-9. R esources N ot C arried Forw ard for D etailed A nalysis Legend Environmental Justice Concerns c:::J Proposed Project Area No Concerns...11 FEF/FIF C onstruction Environm ental A ssessm ent Page 3-6 Eglin A ir Force B ase, FL Final Figure 3-1. W ater R esources A t or N...Ecological A ssociations and Biological R esources A t or N ear the Proposed A ction Location Ecological Association Flatwoods Landscaped!Urban c:J

Detection of fuze defects by image-processing methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, M.J.

1988-03-01

This paper describes experimental studies of the detection of mechanical defects by the application of computer-processing methods to real-time radiographic images of fuze assemblies. The experimental results confirm that a new algorithm developed at Materials Research Laboratory has potential for the automatic inspection of these assemblies and of others that contain discrete components. The algorithm was applied to images that contain a range of grey levels and has been found to be tolerant to image variations encountered under simulated production conditions.

Prototype Automated Equipment to Perform Poising and Beat Rate Operations on the M577 MTSQ Fuze.

DTIC Science & Technology

1978-09-30

Regulation Machine which sets the M577 Fuze Timer beat rate and the Automatic Poising Machine which J dynamically balances the Timer balance wheel...in trouble shooting., The Automatic Poising Machine Figure 3 which inspects and corrects the dynamic I balance of the Balance Wheel Assembly was...machine is intimately related to the fastening method of the wire to the Timer at one end and the Balance Wheel at the other, a review of the history

A users' manual for MCPRAM (Monte Carlo PReprocessor for AMEER) and for the fuze options in AMEER (Aero Mechanical Equation Evaluation Routines)

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaFarge, R.A.

1990-05-01

MCPRAM (Monte Carlo PReprocessor for AMEER), a computer program that uses Monte Carlo techniques to create an input file for the AMEER trajectory code, has been developed for the Sandia National Laboratories VAX and Cray computers. Users can select the number of trajectories to compute, which AMEER variables to investigate, and the type of probability distribution for each variable. Any legal AMEER input variable can be investigated anywhere in the input run stream with either a normal, uniform, or Rayleigh distribution. Users also have the option to use covariance matrices for the investigation of certain correlated variables such as boostermore » pre-reentry errors and wind, axial force, and atmospheric models. In conjunction with MCPRAM, AMEER was modified to include the variables introduced by the covariance matrices and to include provisions for six types of fuze models. The new fuze models and the new AMEER variables are described in this report.« less

Angular Motion of Projectiles with a Moving Internal Part.

DTIC Science & Technology

1977-02-01

Ball Rotor T317 hellIntermal Projectile RingsM505 Fuze Quasi-linear Angular Motion N\\ ANSTRACT (-jCanhs si rveree side ff naeweemv end identify by...LIST OF FIGURES Figure Page 1. 20mm Shell T282E1 with Arming Ball Rotor .... .......... 20 2. Fast Mode Damping Rate for the 20mm T282E1...fuze has a spherical arming rotor in a cylindrical cavity with small but non-zero clearanc’es (Figure 1). The fourth sa.ell - the 8-inch T317 - showed

Meeting the Challenge: A 1986 History of the Naval Surface Weapons Center

DTIC Science & Technology

1987-05-29

8217GClK JACK lMUITRIUXER DIG Iot I ---, , SUpFt S COMPUTER ’ HEL DE Osi cOeiTROLPRiOCESSO HIGM SPEED ATA BUS OM SWR AU VAGKTtC BIBS11 Closed-Loop...appear. HVAC designers think it can determine if closures need to be installed on ventilation inlets to prevent the ingress of exhaust gases from...and fuze timing errors. If the fuze could be caused to actuate based on target position rather than a predicted time of flight, these errors could be

Hazard classification assessment for the MC3423 detonator shipping package

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, R.B.

1981-11-05

An investigation was made to determine whether the MC3423 detonator should be assigned a DOT hazard classification of Detonating Fuze, Class C Explosive, per Federal Register 49 CFR 173.113, when packaged as specified. This study covers two propagation tests which evaluated the effects of two orientations of the MC3423 in its shipping tray. The method of testing was approved by DOE, Albuquerque Operations Office. Test data led to the recommended hazard classification of Detonating Fuze, Class C Explosive for both orientations of the detonator.

Critical energy for shock initiation of fuze train explosives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, F.E.; Wasley, R.J.; Green, L.G.

1973-01-01

Results of shock initiation experiments conducted for tetryl and A-5 are presented, along with some data on the shock initiation of other explosives. The experiments were conducted using a gun system. An equation which has been useful in correlating these shock data is given. Some applications of the critical energy concept (represented by the above equation), to explosive train designs for NASA space systems are included. The concept's usefulness to DOD ordnance agencies now replacing tetryl in fuze trains with A-5 is also indicated. (auth)

Investigation of small transverse electric CO/sub 2/ waveguide lasers for fuzing applications. Contractor report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hochuli, U.; McGuire, D.

1982-10-01

The properties of a compact, transversely excited, pulsed CO/sub 2/ waveguide laser are studied experimentally with the application of such a laser for an optical fuze transmitter in mind. Such parameters as peak power, pulse width, pulse shape, pulse jitter, repetition rate, beam profile, polarization, laser life, and optimum as mixture are investigated both for 10.6 and 9.6 micron output wavelengths, and for both sealed-off and flowing-gas operation of the laser. A computer simulation of the laser's operation is compared with the experimental results.

Digital Device Architecture and the Safe Use of Flash Devices in Munitions

NASA Technical Reports Server (NTRS)

Katz, Richard B.; Flowers, David; Bergevin, Keith

2017-01-01

Flash technology is being utilized in fuzed munition applications and, based on the development of digital logic devices in the commercial world, usage of flash technology will increase. Digital devices of interest to designers include flash-based microcontrollers and field programmable gate arrays (FPGAs). Almost a decade ago, a study was undertaken to determine if flash-based microcontrollers could be safely used in fuzes and, if so, how should such devices be applied. The results were documented in the Technical Manual for the Use of Logic Devices in Safety Features. This paper will first review the Technical Manual and discuss the rationale behind the suggested architectures for microcontrollers and a brief review of the concern about data retention in flash cells. An architectural feature in the microcontroller under study will be discussed and its use will show how to screen for weak or failed cells during manufacture, storage, or immediately prior to use. As was done for microcontrollers a decade ago, architectures for a flash-based FPGA will be discussed, showing how it can be safely used in fuzes. Additionally, architectures for using non-volatile (including flash-based) storage will be discussed for SRAM-based FPGAs.

Recommended Replacements for Tetryl in Australian Production Fuzes and Related Ordnance,

DTIC Science & Technology

1987-11-01

RDX/AC629 as lead filling confirms comparable or better performance by RDX/AC629 on either of the RDX-based boosters. A -5 leads in Fuze M739 are... S . zinc stearate/graphite 98.0:1.25:0.5:0.25 Comparison: Debrix 18AS 120 1.496 a Extrapolated from data for 98.94:1.06 and 98.69:1.31 formulations...71P 8 1 ~ Aq CENEN on FO A R IAN L/I t A IF. I 4JrgALs RLj A ) R SF L. 6UN~cLASSIFIED -- IM DO AA - 14 F/G 19/1 NL . 1I.. EL6 ’ I lin MRL-R-.lO89 AR

Evaluation of Impact Damage to the Burster Detonation Vessel Caused by Fragments from a Drained M121A1 Chemical Munition Detonated with an Initiation Charge

DOE Office of Scientific and Technical Information (OSTI.GOV)

KIPP, MARLIN E.

2001-12-01

Explosive charges placed on the fuze end of a drained chemical munition are expected to be used as a means to destroy the fuze and burster charges of the munition. Analyses are presented to evaluate the effect of these additional initiation charges on the fragmentation characteristics for the M121A1 155mm chemical munition, modeled with a T244 fuze attached, and to assess the consequences of these fragment impacts on the walls of a containment chamber--the Burster Detonation Vessel. A numerical shock physics code (CTH) is used to characterize the mass and velocity of munition fragments. Both two- and three-dimensional simulations ofmore » the munition have been completed in this study. Based on threshold fragment velocity/mass results drawn from both previous and current analyses, it is determined that under all fragment impact conditions from the munition configurations considered in this study, no perforation of the inner chamber wall will occur, and the integrity of the Burster Detonation Vessel is retained. However, the munition case fragments have sufficient mass and velocity to locally damage the surface of the inner wall of the containment vessel.« less

Signal-processing analysis of the MC2823 radar fuze: an addendum concerning clutter effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jelinek, D.A.

1978-07-01

A detailed analysis of the signal processing of the MC2823 radar fuze was published by Thompson in 1976 which enabled the computation of dud probability versus signal-to-noise ratio where the noise was receiver noise. An addendum to Thompson's work was published by Williams in 1978 that modified the weighting function used by Thompson. The analysis presented herein extends the work of Thompson to include the effects of clutter (the non-signal portion of the echo from a terrain) using the new weighting function. This extension enables computation of dud probability versus signal-to-total-noise ratio where total noise is the sum of themore » receiver-noise power and the clutter power.« less

Enhancing Energy in Future Conventional Munition

NASA Astrophysics Data System (ADS)

Peiris, Suhithi

2017-06-01

Future conventional weapons are envisioned to contain more energy per volume than current weapons. Current weapons comprise of inert steel outer case, with inner volume for energetic materials, fuzing, sensor package, propulsion system, etc. Recent research on reactive materials (RM) & new energetics, and exploiting additive manufacturing can optimize the use of both mass and volume to achieve much higher energy in future weapons. For instance, replacing inert steel with RM of similar strength, additively manufacturing fuzing packages within the weapon form factor, and combing the whole with new energetics, will enable the same lethality effects from smaller weapons as obtained from today's larger weapons. This paper will elaborate on reactive materials and properties necessary for optimal utilization in various weapon features, and touch on other aspects of enhancing energy in future conventional munition.

Sandia Research and Development Board: Minutes of the 33rd Meeting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castle, M.

1950-02-08

Notes about the barometric fuzing system testing, drops of stockpile weapons requested by the Strategic Air Command, simultaneous drops and the interaction of the baro systems, changes of desired military characteristics of atomic weapons.

Proximity fuze

DOEpatents

Harrison, Thomas R.

1989-08-22

A proximity fuze system includes an optical ranging apparatus, a detonation circuit controlled by the optical ranging apparatus, and an explosive charge detonated by the detonation cirtcuit. The optical ranging apparatus includes a pulsed laser light source for generating target ranging light pulses and optical reference light pulses. A single lens directs ranging pulses to a target and collects reflected light from the target. An optical fiber bundle is used for delaying the optical reference pulses to correspond to a predetermined distance from the target. The optical ranging apparatus includes circuitry for providing a first signal depending upon the light pulses reflected from the target, a second signal depending upon the light pulses from the optical delay fiber bundle, and an output signal when the first and second signals coincide with each other. The output signal occurs when the distance from the target is equal to the predetermined distance form the target. Additional circuitry distinguishes pulses reflected from the target from background solar radiation.

Computing the apparent centroid of radar targets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, C.E.

1996-12-31

A high-frequency multibounce radar scattering code was used as a simulation platform for demonstrating an algorithm to compute the ARC of specific radar targets. To illustrate this simulation process, several targets models were used. Simulation results for a sphere model were used to determine the errors of approximation associated with the simulation; verifying the process. The severity of glint induced tracking errors was also illustrated using a model of an F-15 aircraft. It was shown, in a deterministic manner, that the ARC of a target can fall well outside its physical extent. Finally, the apparent radar centroid simulation based onmore » a ray casting procedure is well suited for use on most massively parallel computing platforms and could lead to the development of a near real-time radar tracking simulation for applications such as endgame fuzing, survivability, and vulnerability analyses using specific radar targets and fuze algorithms.« less

Estimate of Errors of Pressure Predictions Without Meteorological Forecasts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1957-07-31

Independent methods of estimating pressure were considered-- the range of application in height is from that of baro-fuzed tactical weapons (a few thousand feet) to that of the control of height of aircraft at high altitude (45,000 feet).

Italian Bombs & Fuzes

DTIC Science & Technology

1948-06-01

document states that the practice of galvanising aircraft bombs has ceased, and that a protective coat of paint is now used instead. These colourings...that the Italians are still in possession of large stocks of galvanised bombs. SECTION I CHEMICAL WARFARE BOMBS No. C.W. bombs have yet been

Impact fuze testing at 3000 m/sec employing explosively accelerating plates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gill, W.

1981-01-01

The Explosives Testing Division at Sandia has developed a method of simulating a re-entry vehicle impacting the ground. The purpose of the simulation is to evaluate different fusing concepts. The design and operation of this impact testing facility are described.

Proximity fuze

DOEpatents

Harrison, T.R.

1987-07-10

A proximity fuze system includes an optical ranging apparatus, a detonation circuit controlled by the optical ranging apparatus, and an explosive charge detonated by the detonation circuit. The optical ranging apparatus includes a pulsed laser light source for generating target ranging light pulses and optical reference light pulses. A single lens directs ranging pulses to a target and collects reflected light from the target. An optical fiber bundle is used for delaying the optical reference pulses to correspond to a predetermined distance from the target. The optical ranging apparatus includes circuitry for providing a first signal depending upon the light pulses reflected from the target, a second signal depending upon the light pulses from the optical delay fiber bundle, and an output signal when the first and second signals coincide with each other. The output signal occurs when the distance from the target is equal to the predetermined distance from the target. Additional circuitry distinguishes pulses reflected from the target from background solar radiation. 3 figs.

Proximity fuze

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harrison, T.R.

1987-07-10

A proximity fuze system includes an optical ranging apparatus, a detonation circuit controlled by the optical ranging apparatus, and an explosive charge detonated by the detonation circuit. The optical ranging apparatus includes a pulsed laser light source for generating target ranging light pulses and optical reference light pulses. A single lens directs ranging pulses to a target and collects reflected light from the target. An optical fiber bundle is used for delaying the optical reference pulses to correspond to a predetermined distance from the target. The optical ranging apparatus includes circuitry for providing a first signal depending upon the lightmore » pulses reflected from the target, a second signal depending upon the light pulses from the optical delay fiber bundle, and an output signal when the first and second signals coincide with each other. The output signal occurs when the distance from the target is equal to the predetermined distance from the target. Additional circuitry distinguishes pulses reflected from the target from background solar radiation. 3 figs.« less

A Sandia weapon review bulletin : defense programs, Autumn 1992.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-09-01

Topics in this issue: (1) Focal Point and STEP. Sandia National Laboratories has always focused its advanced weapon development not only on future weapon needs, but also on the engineering and manufacturing sciences needed to meet them. Both areas are changing dramatically. As the nation dismantles many of its warheads, it becomes essential that those that remain are increasingly reliable, secure, capable, and safe. And as development resources diminish, it becomes vital that they are applied to the most critical technologies in a disciplined manner. The mission of the Focal Point program and the Stockpile Transition Enabling Program (STEP) ismore » to develop processes for meeting these challenges. Focal Point offers a decision-making process for allocating Sandia's resources to meets its defense programs strategic goals. (2) Defense Programs news in brief. (3) Dismantling the nuclear stockpile. (4) W88/MK5: Arming, Fuzing, and Firing system meets all requirements and goals. (5) The Common Radar Fuze. (6) Insertable-explosive arming of firing sets. (7) Preparing for fewer underground tests.« less

Proximity fuze

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harrison, T.R.

1989-08-22

A proximity fuze system is described. It includes an optical ranging apparatus, a detonation circuit controlled by the optical ranging apparatus, and an explosive charge detonated by the detonation circuit. The optical ranging apparatus includes a pulsed laser light source for generating target ranging light pulses and optical reference light pulses. A single lens directs ranging pulses to a target and collects reflected light from the target. An optical fiber bundle is used for delaying the optical reference pulses to correspond to a predetermined distance from the target. The optical ranging apparatus includes circuitry for providing a first signal dependingmore » upon the light pulses reflected from the target, a second signal depending upon the light pulses from the optical delay fiber bundle, and an output signal when the first and second signals coincide with each other. The output signal occurs when the distance from the target is equal to the predetermined distance from the target. Additional circuitry distinguishes pulses reflected from the target from background solar radiation.« less

A Hardware Platform for Characterizing and Validating 1-Dimensional Optical Systems

DTIC Science & Technology

2014-09-01

principle laboratory experiments, a bread -board sensor and data collection system was created to gather fuze data to postprocess after the event...merely differentiates this bistable memory category from dynamic random access memory [RAM], which must be periodically refreshed to retain data.) A

42nd Annual Armament Systems: Gun and Missile Systems

DTIC Science & Technology

2007-04-26

to compare the various contenders: • FCS • Aero and flight dynamics of rounds • Phit and lethality • Direct and indirect fire capability Defence R&D...each other). • Guidance: Unguided, Command Guidance, Lock on Before Launch, Autonomous (needs Phit analysis). • Fuzing: Proximity – RF or Optical

Probabilities of Occurrence of Baro-Fuze System Errors More Than 1000 Feet Too Low Due to Ignoring the Meteorological Forecast

DOE Office of Scientific and Technical Information (OSTI.GOV)

Charles, B.N.

1955-05-12

Charts of the geographical distribution of the annual and seasonal D-values and their standard deviations at altitudes of 4500, 6000, and 7000 feeet over Eurasia are derived, which are used to estimate the frequency of baro system errors.

XM746 Practice Fuze.

DTIC Science & Technology

1980-01-31

SANDMILLISEC HARD SAND .. : 33 20!~ U SMOKE EXIT RELATIONSHIP pd TO XMBO04 PROJ SURIAL DEPTH AS A FUNCTION OF EXIT HOLE LOCATION IMP VEL - 900 PT/SIC IMP...distance between the be determined. Adenes evlope for then obser- 30% ordinate and 16% or 84% The 0confidence level" d- Ttons was derived as follows

PEO Ammunition Systems Portfolio Book 2012-2013

DTIC Science & Technology

2011-02-02

assembly. Aluminum ogive contains firing pin, a rubber anti-creep spring and M550 fuze escapement assembly and is threaded to projectile body...51 The Mortar Weapons and Fire Control Family M95/M96 Mortar Fire Control System (MFCS) – Mounted...52 M150/M151 Mortar Fire Control System Dismounted (MFCS-D

Further Development, Fabrication, and Testing of XM36E1 Fuze Setter

DTIC Science & Technology

1978-08-01

primary func- tion of this circuit, has the same timing characteristics as the original circuit: Half-period pulses are required to be greater than...temperature of -40 0 C. 9 The following corrective action was taken for this mal- fuction : (1) The batteries were replaced, and an investigation of battery

76 FR 76954 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-09

... Bombs, 1000 BLU-117 2000lb General Purpose Bombs, 600 BLU-109 2000lb Hard Target Penetrator Bombs, and four BDU-50C inert bombs, fuzes, weapons integration, munitions trainers, personnel training and... kits, 3300 BLU-111 500lb General Purpose Bombs, 1000 BLU-117 2000lb General Purpose Bombs, 600 BLU-109...

U. S. Naval Forces, Vietnam Monthly Historical Summary for December 1970

DTIC Science & Technology

1971-02-15

cable 3 cans of pull friction fuze lighters 2 electronic repair kits 1 bag of outboard motor repair parts 4 large bags of medical supplies and food ...problems encountered in the operation such as an operation order in Franch which the Vietnamese participants could not readsand raw and un:rained Cambodian

Predictive Factors in Conflict: Assessing the Likelihood of a Preemptive Strike by Israel on Iran Using a Computer Model

DTIC Science & Technology

2013-03-01

Proliferation Treaty OSINT Open Source Intelligence SAFF Safing, Arming, Fuzing, Firing SIAM Situational Influence Assessment Module SME Subject...expertise. One of the analysts can also be trained to tweak CAST logic as needed. In this initial build, only open-source intelligence ( OSINT ) will

50th Annual Fuze Conference. Session 1 and 2

DTIC Science & Technology

2006-05-11

PROGRAM OFFICE AMSRD-AAR-AIJ J. Goldman X6060 STRATEGIC MGT OFFICE AMSRD-AAR-EMS D. Denery X6081 KNOWLEDGE MANAGEMENT OFFICE AMSRD-AAR-EMK G. Albinson...Tail-Mounted Configuration (MK-82 Demo) UHF to L-Band Pulse Doppler Radar Using Low Cost COTS Components Nose and Tail Mount Configurations Only

Environmental Effects on Data Retention in Flash Cells

NASA Technical Reports Server (NTRS)

Katz, Rich; Flowers, David; Bergevin, Keith

2017-01-01

Flash technology is being utilized in fuzed munition applications and, based on the development of digital logic devices in the commercial world, usage of flash technology will increase. Antifuse technology, prevalent in non-volatile field programmable gate arrays (FPGAs), will eventually be phased out as new devices have not been developed for approximately a decade. The reliance on flash technology presents a long-term reliability issue for both DoD and NASA safety- and mission-critical applications. A thorough understanding of the data retention failure modes and statistics associated with Flash data retention is of vital concern to the fuze safety community. A key retention parameter for a flash cell is the threshold voltage (VTH), which is an indirect indicator of the amount of charge stored on the cells floating gate. This paper will present the results of our on-going tests: long-term storage at 150 C for a small population of devices, neutron radiation exposure, electrostatic discharge (ESD) testing, and the trends of large populations (over 300 devices for each condition) exposed to three difference temperatures: 25 C, 125 C, and 150 C.

Using Modeling and Simulation to Complement Testing for Increased Understanding of Weapon Subassembly Response.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wong, Michael K.; Davidson, Megan

As part of Sandia’s nuclear deterrence mission, the B61-12 Life Extension Program (LEP) aims to modernize the aging weapon system. Modernization requires requalification and Sandia is using high performance computing to perform advanced computational simulations to better understand, evaluate, and verify weapon system performance in conjunction with limited physical testing. The Nose Bomb Subassembly (NBSA) of the B61-12 is responsible for producing a fuzing signal upon ground impact. The fuzing signal is dependent upon electromechanical impact sensors producing valid electrical fuzing signals at impact. Computer generated models were used to assess the timing between the impact sensor’s response to themore » deceleration of impact and damage to major components and system subassemblies. The modeling and simulation team worked alongside the physical test team to design a large-scale reverse ballistic test to not only assess system performance, but to also validate their computational models. The reverse ballistic test conducted at Sandia’s sled test facility sent a rocket sled with a representative target into a stationary B61-12 (NBSA) to characterize the nose crush and functional response of NBSA components. Data obtained from data recorders and high-speed photometrics were integrated with previously generated computer models in order to refine and validate the model’s ability to reliably simulate real-world effects. Large-scale tests are impractical to conduct for every single impact scenario. By creating reliable computer models, we can perform simulations that identify trends and produce estimates of outcomes over the entire range of required impact conditions. Sandia’s HPCs enable geometric resolution that was unachievable before, allowing for more fidelity and detail, and creating simulations that can provide insight to support evaluation of requirements and performance margins. As computing resources continue to improve, researchers at Sandia are hoping to improve these simulations so they provide increasingly credible analysis of the system response and performance over the full range of conditions.« less

Present Capability of Ram Air-Driven Alternators Developed at HDL as Fuze Power Supplies

DTIC Science & Technology

1983-07-01

DRCPI-HD, HELLFIRE/GLD FT MONMOUTH, NJ 07703 ATTN DRCPM-PEv PERSHING ATTN DRCPM-DT, TOM DRAGON DIRECTOR REDSTONE ARSENAL, AL 35809 ELECTRONICS TECHNOLOGY...00211 ATTN G. POPE, 00211 ATTN C. LANHAM, 00213 ATTi C. SPYROPOULOS, 22100 ATTN P. INGERSOLL, 34000 ATTN J. BEARD , 34200 ATn D. BROGU., 34300 I ATTN

55th Annual Fuze Conference

DTIC Science & Technology

2011-05-26

concrete plate and compact soil Confirmation: Complete Success both tests The TDD functioned as programmed; traces show entry and exit from each...concrete target and difference in deceleration levels between concrete and soil configuration The final exit & fire signals were generated as planned...Technical Data Package • Determine Process Capability • FMEA Manufacturing • Determine process capability • Cp = ( USL -LSL)/(6*Sigma) • Cpl

34th Annual Gun and Ammunitions Symposium and Exhibition held in Monterey, CA on 26-29 April 1999

DTIC Science & Technology

1999-04-01

Allan Buckley, Oerlikon Contraves ൫/50MM HETF (High Explosive Time Fuze) Ammunition" by Mr. Stephen Kerk and Mr. Peter Moore,* Diehl Stifung & Co...Technologies, Inc. "OICW Fire Control System" by Mr. Grant Moule*; Ms. Susan Franciscus*, Contraves Brashear Systems L.P. "Air Bursting Systems" by Mr. John

Patterning of Thick Parylene Films by Oxygen Plasma for Application as Exploding Foil Initiator Flyer Material

DTIC Science & Technology

2009-09-01

exploding foil initiator ( EFI ) type fuzes are being explored to...Acronyms Au gold Cr chromium Cu copper EFI exploding foil initiator BOE buffered oxide etch MEMS microelectromechanical systems RIE reactive ion...Patterning of Thick Parylene Films by Oxygen Plasma for Application as Exploding Foil Initiator Flyer Material by Eugene Zakar and Michael

Against the Wind: Five South Africans Follow Their Dreams.

ERIC Educational Resources Information Center

Lewis, Lesley

This book for beginning readers tells the story of five South Africans who, though not very famous, all did things that no black South African had ever done before. They include: Simon Mkhize who, year after year, ran the Comrades Marathon unofficially, ignoring its racial bans; Magema M. Fuze, who was the first black South African to publish a…

7. BUILDING 604F, INTERIOR OF BULL PEN SHOWING TESTING STAND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. BUILDING 604-F, INTERIOR OF BULL PEN SHOWING TESTING STAND AND HEAVY WOOD LINING ON CONCRETE WALLS. STEEL PLATE ABOVE TEST STAND DEFLECTS SHRAPNEL, SCREEN FURTHER HELPS TO CONTAIN PARTICLES. ONLY SMALL EXPLOSIVES WERE TESTED HERE (GRENADES, MINES, BOMB FUZES, ETC.). - Picatinny Arsenal, 600 Area, Test Areas District, State Route 15 near I-80, Dover, Morris County, NJ

Advanced Analog Signal Processing for Fuzing Final Report CRADA No. TC-1306-96

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fu, C. Y.; Spencer, D.

The purpose of this CRADA between LLNL and Kaman Aerospace/Raymond Engineering Operations (Raymond) was to demonstrate the feasibility of using Analog/Digital Neural Network (ANN) Technology for advanced signal processing, fuzing, and other applications. This cooperation sought to Ieverage the expertise and capabilities of both parties--Raymond to develop the signature recognition hardware system, using Raymond’s extensive experience in the area of system development plus Raymond’s knowledge of military applications, and LLNL to apply ANN and related technologies to an area of significant interest to the United States government. This CRADA effort was anticipated to be a three-year project consisting of threemore » phases: Phase I, Proof-of-Principle Demonstration; Phase II, Proof-of-Design, involving the development of a form-factored integrated sensor and ANN technology processo~ and Phase III, Final Design and Release of the integrated sensor and ANN fabrication process: Under Phase I, to be conducted during calendar year 1996, Raymond was to deliver to LLNL an architecture (design) for an ANN chip. LLNL was to translate the design into a stepper mask and to produce and test a prototype chip from the Raymond design.« less

An Evaluation of Flash Cells Used in Critical Applications

NASA Technical Reports Server (NTRS)

Katz, Rich; Flowers, David; Bergevin, Keith

2016-01-01

Due to the common use of Flash technology in many commercial and industrial Programmable Logic Devices (PLDs) such as FPGAs and mixed-signal microcontrollers, flash technology is being utilized in fuzed munition applications. This presents a long-term reliability issue for both DoD and NASA safety- and mission-critical applications. A thorough understanding of the data retention failure modes and statistics associated with Flash data retention is of vital concern to the fuze safety community. A key retention parameter for a flash cell is the threshold voltage (VTH), which is an indirect indicator of the amount of charge stored on the cells floating gate. Initial test results based on a study of charge loss in flash cells in an FPGA device is presented. Statistical data taken from a small sample set indicates quantifiable charge loss for devices stored at both room temperature and 150 C. Initial evaluation of the distribution of threshold voltage in a large sample set (800 devices) is presented. The magnitude of charge loss from exposure to electrostatic discharge and electromagnetic fields is measured and presented. Simulated data (and measured data as available) resultant from harsh-environment testing (neutron, heavy ion, EMP) is presented.

50th Annual Fuze Conference.Session 3 and 4

DTIC Science & Technology

2006-05-11

Exploding Foil Initiator Research • Research on Explosives • Conclusion Wim Prinse Research Scientist3 TNO has organised...Research Scientist6 Exploding Foil Initiator Research • Electrical circuit • Exploding foil • Velocity of the flyer • Driver Explosive • Secondary...90% efficiency of energy deposited in the exploding foil (50 % other circuits) Wim Prinse Research Scientist8 Exploding foil • Dimension of the foil

Annual Fuze Conference and Munitions Technology Symposium VI (43rd)

DTIC Science & Technology

1999-04-07

part manufacture and assembly and identify the parameters that we must control through production. Analyzing the coefficients of variation and the...processing energetic materials. The extruder is equipped with four independent temperature control zones, segmented screws, a jacketed die block capable of...and has vacuum capability. Data monitoring capabilities include melt temperature and pressure, torque, screw speed, and temperatures in all of the

2005 Precision Strike Annual Programs Review

DTIC Science & Technology

2005-04-20

Control Canards (4) Polyurethane Foam Support DPICM (404 M101 Grenades) Warhead Fuze: Electronic Safe & Arm Device (ESAD) UNCLASSIFIED UNCLASSIFIED PF...SYSTEMS: • JASSM: Colonel James Geurts, USAF JASSM PM • ATACMS : Colonel Earnest Harris, USA PM, Precision Fires Rockets & Missiles, PEO Space and...UNCLASSIFIED UNCLASSIFIED Viper Strike Lineage ATACMS Delivered Base BATs Viper Strike SAL Seeker Proof of Principle Demos I & II Hunter-Viper Strike

UXO Live Site Classification Demonstrations: A Retrospective Summary

DTIC Science & Technology

2017-10-01

performance ROC Curve Number of True Clutter Incorrectly Classified TO I R em ed ia tio n: Pe rc en t o f T ru e TO I Co rr ec tly C la ss ifi ed...rocket, 382 practice bomb , M103 bomb nose fuze, 100lb bomb , M1 practice bomb MPV, TEMTADS 2x2 2014 Waikoloa Waikoloa, HI 9 small ISO, 37mm, medium

2008 Munitions Executive Summit

DTIC Science & Technology

2008-02-21

7:00pm Hosted Reception 2008 Munitions Executive Summit February 20, 2008 – AGENDA (cont.) 8:00am Administrative Remarks 8:05am PEO Keynote Address...MES Awards Tuesday, February 19 5pm Reception /Pre-registration Sponsored by ATK Ammunition Systems Group and Kaman Aerospace’s Fuzing...15pm Adjourn 5:15pm - 7pm Hosted Reception Sponsored by DSE, Inc. and General Dynamics-OTS Munitions executive suMMit 2008 agenda & prograM

51st Annual Fuze Conference

DTIC Science & Technology

2007-05-27

5:00PM - Opening Reception 6:30PM WEDNESDAY, MAY 23, 2007 (General Session) TUESDAY, MAY 22, 2007 (Early Registration) 11:50 AM - LUNCHEON 1:00 PM... RECEPTION 7:00 PM WEDNESDAY, MAY 23, 2007 (Parallel Sessions) Session IVA - OPEN SESSION Chair: Mr. Telly Manolatos, Electronics Development Corporation...company’s logo in the agenda handouts and proceedings o Signage outside the particular event sponsored o Sponsor ribbon on badges • Reception - $8,000

Air Bursting Munition ABM Medium Calibre Applications

DTIC Science & Technology

2001-04-18

NDIA 45th Annual Fuze Conference - Long Beach, CA - April 16-18, 2001 Folie 1 P2 15548 BB, P-VP/FD/11, © 2001 Oerlikon Contraves AG, Zürich...Switzerland Air Bursting Munition ABM Medium Calibre Applications Allan Buckley & Pierre Freymond Oerlikon Contraves Pyrotec AG CH-8050 Zurich...Project Number Task Number Work Unit Number Performing Organization Name(s) and Address(es) Oerlikon Contraves Pyrotec AG CH-8050 Zurich / Switzerland

78 FR 31902 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-28

...-557C/B (GBU-31) w/SAASM/AJ 4 JDAM BLU-109 Load Build Trainers 6 MK-82 Filled Inert Bombs 4 BLU-109 Inert Bombs 1312 FMU-152A/B Fuzes (FZU-63 Initiator) 542 GBU-39/B Small Diameter Bombs 530 BLU-109 2000LB Penetrators 780 GBU-12 Bomb 4 GBU-12 Dummy Trainers 154 AIM-9X-2 (Blk II) Tactical Missiles w/DSU...

National Radar Conference, Los Angeles, CA, March 12, 13, 1986, Proceedings

NASA Astrophysics Data System (ADS)

The topics discussed include radar systems, radar subsystems, and radar signal processing. Papers are presented on millimeter wave radar for proximity fuzing of smart munitions, a solid state low pulse power ground surveillance radar, and the Radarsat prototype synthetic-aperture radar signal processor. Consideration is also given to automatic track quality assessment in ADT radar systems instrumentation of RCS measurements of modulation spectra of aircraft blades.

Aircraft Survivability. Spring 2011

DTIC Science & Technology

2011-01-01

test Figure 4 Mixed Lagrangian and SPH Simulation of the Bullet Impacting the Floor Section Figure 5 Predictions of Damage to Penetrator, CMC Layer...aircraft and regulating the flow of liquid to simulate both the intrinsic change in plume intensity and the apparent change in intensity of a simulated ...the development of a digital simulation to conduct end game studies of the Eagle missile warhead- fuze combination. This was one of the first

Director, Operational Test and Evaluation FY 2004 Annual Report

DTIC Science & Technology

2004-01-01

HIGH) Space Based Radar (SBR) Sensor Fuzed Weapon (SFW) P3I (CBU-97/B) Small Diameter Bomb (SDB) Secure Mobile Anti-Jam Reliable Tactical Terminal...detection, identification, and sampling capability for both fixed-site and mobile operations. The system must automatically detect and identify up to ten...staffing within the Services. SYSTEM DESCRIPTION AND MISSION The Services envision JCAD as a hand-held device that automatically detects, identifies, and

Feasibility of Standardized Rain Testing for Fuzes. Serial Number 1.0

DTIC Science & Technology

1981-06-01

produced by ;he drops in a small volume with a laser beam. /, -- Il 8’ 15𔃻 -. - II11,, I - - Il i Io " illli A pr c i / con3 1de at o Is sh ll d o u d r...of collapse of the spherical bubbles in an asymmetric mode such that hlqh velocity microjets impinqe on the surface. It appears cavitation microjet

A Reactor Development Scenario for the FuZE Sheared-Flow Stabilized Z-pinch

NASA Astrophysics Data System (ADS)

McLean, Harry S.; Higginson, D. P.; Schmidt, A.; Tummel, K. K.; Shumlak, U.; Nelson, B. A.; Claveau, E. L.; Forbes, E. G.; Golingo, R. P.; Stepanov, A. D.; Weber, T. R.; Zhang, Y.

2017-10-01

We present a conceptual design, scaling calculations, and development path for a pulsed fusion reactor based on a flow-stabilized Z-pinch. Experiments performed on the ZaP and ZaP-HD devices have largely demonstrated the basic physics of sheared-flow stabilization at pinch currents up to 100 kA. Initial experiments on the FuZE device, a high-power upgrade of ZaP, have achieved 20 usec of stability at pinch current 100-200 kA and pinch diameter few mm for a pinch length of 50 cm. Scaling calculations based on a quasi-steady-state power balance show that extending stable duration to 100 usec at a pinch current of 1.5 MA and pinch length of 50 cm, results in a reactor plant Q 5. Future performance milestones are proposed for pinch currents of: 300 kA, where Te and Ti are calculated to exceed 1-2 keV; 700 kA, where DT fusion power would be expected to exceed pinch input power; and 1 MA, where fusion energy per pulse exceeds input energy per pulse. This work funded by USDOE ARPA-E and performed under the auspices of Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-734770.

Standardization of a Safing and Arming Device for Artillery Ammunition

DTIC Science & Technology

1976-10-01

designated by other author- ized documents. UNCLASSIFIED SECURITY CLASSIFICATION OF THIS PAGE (When Dala Entered) REPORT DOCUMENTATION PAGE READ...establish the physical and military requirements. Design studies were initiated on the current S&A devices. • DD FOR’* •’*• 1 JAN 73 1473...A developer. In the design of any mechanism, a precise definition of S&A requirements for all fuze applications is required prior to development

An Organizational Analysis Model for Navy Field-Level Comptrollership.

DTIC Science & Technology

1980-09-01

organization with some self -control despite interdepen- dence with the environment. But if we are to gain understanding, we must consider both in the...involve a self -protective reaction. The short time fuze allows the decision to be made without outside input or approval. The following discussion will...no real standard ways of running a Comptroller Department. 51. Establishment of self with C.O. and department heads. 52. Learning the underlying

A Shotline Method for Modeling Projectile Geometry

DTIC Science & Technology

1986-06-01

by block number) GIFT Target Description Vulnerability Analysis COMGEOM Shotlining Warhead Lethality MISFIR 20. ABSTRACT fConfteue an r»r»r«» eUm It rt...target interaction is centered upon the program MISFIR, written in CDC Fortran 5. MISFIR is built on the formalisms of the GIFT (Geometric...a ray-tracing subroutine added to GIFT (viz. SHOTCYL); MISFIR itself, together with its subprograms; and an application program, called FUZES, which

46th Annual Gun and Missile Systems Conference and Exhibition. Volume 3 - Thursday

DTIC Science & Technology

2011-09-01

Grade Sensors Through Use of Accelerated Aging Principles Mr. Scott Gift 11657 Modeling of the Autofrettage Processes of a Gun Barrel Mr. Sudhir...Emissions Measured on the Outer Portion of a Composite Barrel Ms. Rushie Ghimire GUN & MISSILE SYSTEMS ADDITIONAL AUTHORS GUN & MISSILE SYSTEMS...Transportation – Loading – Gun Fire to Barrel Exit – After Barrel Exit • Passing: Fuze safety devices remain safe; safe for disposal or safe for

50th Annual Fuze Conference Sessions 3 and 4 Held in Norfolk, Virginia on May 9-11, 2006

DTIC Science & Technology

2006-05-11

Exploding Foil Initiator Research • Research on Explosives • Conclusion Wim Prinse Research Scientist3 TNO has organised...Research Scientist6 Exploding Foil Initiator Research • Electrical circuit • Exploding foil • Velocity of the flyer • Driver Explosive • Secondary...90% efficiency of energy deposited in the exploding foil (50 % other circuits) Wim Prinse Research Scientist8 Exploding foil • Dimension of the foil

A Summary Report on Store Heating Technology

DTIC Science & Technology

1978-09-01

from aerodynamic heating effects. Almost all present-day bombs and fuzes have, as their explosive charge, some form of TNT which melts at about 178...deg. This was achieved on flights 14, 16, 18, 19, and 20. Flight 15 was a subsonic mission to perform afterburner tests, and flight 17 was aborted...BDU-12 at a Mach number of 2.5. Of course, this store did not contain TNT and was in no way restricted by the temperature limitations previously

Operation of the Chemical Agent Munitions Disposal System (CAMDS) at Tooele Army Depot, Utah.

DTIC Science & Technology

1978-09-01

parts furnace where the container is opened to expose the agent; the agent is boiled out and burned ; and the residual container is heat treated for...fuze booster to expose the booster pellet so it will burn instead of detonate in the Deactivation Furnace. A portion of the solution in the coolant...demilitarization equipment exposed to agent GB will be chemically decontaminated to prepare for operations with burstered mustard projectiles. The

US Army battery needs -- Present and future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamlen, R.P.; Christopher, H.A.; Gilman, S.

1995-07-01

The purpose of this paper is to describe the needs of the US Army for silent portable power sources, both in the near and longer term future. As a means of doing this, the programs of the Power Sources Division of the Army Research Laboratory will be discussed. The six program areas in which the Power Sources Division is engaged are: primary batteries, rechargeable batteries, reserve/fuze batteries, pulse batteries and capacitors, fuel cells, and thermophotovoltaic power generation.

Test Operations Procedure (TOP) 4-2-013 Commodity Engineering Test Procedures, Recoilless Rifle Ammunition

DTIC Science & Technology

2009-09-22

test officer). At a minimum, the CIL will be conducted at the operator level (often referred to as “field strip and clean”). More detailed...is checked before each shot is fired. Use a boresight (optical or laser ) as necessary to check alignment to the target aiming point if the barrel is...for this test should be representative of production. All components must be present, including projectile paint and markings, fuzes, any tool

System Architecture for a Military Weapon System Development Process to Integrate Design and the Manufacturing Process for Use by a Government Technical Development Agency

DTIC Science & Technology

2014-09-01

elements of functional structure. Frequently the requirement for this is to ensure long- term retention of skilled people through the provision of an...operational and manufacturable, greatly reducing the design work remaining for Milestone C. 14. SUBJECT TERMS System Architecture, manufacturing...specialized ammunition technology item such as a fuze takes too long, from initial concept through final production design, which is approved for

Production Methodology for the Validation of Electronic Fuzes

DTIC Science & Technology

1980-11-01

are employed age cantridge o; magazine This mud’e is shown in figure Vtll-t (f) Fxtensis’e debuggngij and troubleshooting to perfect the automatic...All the plastic manterials platens The heat is supplied bs steam, heated can be fabricated b% more than one methoid , al- liquids, electrical res.stance...on-I-ne data bases, or the real-time data acquisition Resources %%ill be performizble- Thus. tbe adsantages that cook ;i be realized by full use of

MineWolf Tiller Test and Evaluation

DTIC Science & Technology

2007-11-01

scale. Reheat and reweigh until no change in mass is recorded. Soil is then dry. Calculations The moisture content of a soil is expressed as a... MOISTURE % WET DENSITY KG/M³ DRY DENSITY KG/M³ 1 07-Sep-06 gravel 10cm 4 2731 2621 2 07-Sep-06 gravel 10cm 4 2653 2541 3 07-Sep-06 gravel 10cm 3...each soil condition. This table also indicates the number of untriggered fuzes which were found separated from their main charges. The notes

Cost-Reduced M587 Electronic Time Fuze: Root Cause Analysis of July 1979 Early Bursts

DTIC Science & Technology

1981-04-01

capacitor during gunfire, coupled with an intermit - tent wire bond (which opens during setback and then closes again) can defeat the initialization circuit...is calibrated, (c) the set time is checked out in fast time to verify that the setting has actually been achieved, and (d) the setter visually com...insensitive to supply voltage. One of the reasons for choosing the twin-T design was because it was possible to preclude fail- fast failure modes. The

Annual Fuze Conference (54th) Held in Kansas City, Missouri on May 11-13, 2010

DTIC Science & Technology

2010-05-13

approaches to development • Lets get something straight !!! – Experimentation (A few of a kind) • Focus on answering questions (is it useful?, how does it...machines are applicable / available • How do the machines work • Where do they get their reference • What kind of tolerances are they capable of...Tactical Benefits: • Fastest way to get local reconnaissance images • Totally impervious to weather/gusts • ~ $20/round Background History New

Linear Theory of a Projectile With a Rotating Internal Part in Atmospheric Flight

DTIC Science & Technology

2003-07-01

shape, or form. Fuze mechanisms used on some indirect fire ammunition employ a rotor that is permitted to move slightly with respect to the main...series of experiments where a projectile with a loose internal part was driven by the rotor of a freely gimbaled gyroscope. The gyroscope yaw history...cases, weapon system designers require guidance on the effect of the rotating internal part as well as guidance on how to optimally configure such a

Minutes of FSC 5935, Connector Standardization Planning Meeting Held at Dayton, Ohio on 25-27 August 1982.

DTIC Science & Technology

1982-11-30

the cost of an alternate signal set: - Power - Bidirectional data link (point-to-point) (plus store receptacle or induction coil) b. FUNCTION...digital fuzes had been implemented. The first presentation described an inductive data link for surface launched projectiles which sent both power and...AD-A130 681 MINUTES OF FSC 5935 CONNECTOR STANDARDIZATION PLANNING 1/2 MEETING HELD AT DAYTON OHIO ON 25-27 AUGUST 1982WU) DEFENSE ELECTRONICS SUPPLY

Development Program of Dual Mode Impact Delay Module for Artillery Fuzes.

DTIC Science & Technology

1979-12-31

analysis phase to demonstrate design confidence and reliability of performance in the artillery firing environment. See Figure I for drawing of the latest...Device P/N KF88590 as proposed by us. This analysis will be based on results of penalty test« in which the test variables will include loading and...istently and unmistakably Dextrinated lead azide was, tent surrogate. On the basis of stab s Id be predicted that any system whi r mated lead azide

High Temperature/Solar Effects Testing on Various Munitions

DTIC Science & Technology

1992-08-01

days. Follming conditioning, a variety of laboratory and ballistic tests are performed t o assess safety and performame. The test i t e m s are...ranging from 60-mm cartridges to 8-inch projectiles. anununition types including fuzes and anti-tank rockets. The first phase w a s conducted from...container with a foam liner. Each cartridge w a s in its individual fiber Each cartridge was packed in a fiber cartridge, 120-nun: APFSRS-T, M829Al

Study of Damped Set-Back Pins for S and A Mechanisms.

DTIC Science & Technology

1976-11-01

arm device for artillery munitions. This damped set-back pin assembly is one of two safety features on a S and A device used in the M739 PD/XM587 ET...The damped set-back pin study program was for the design, testing, fabrication, and delivery and damped set-back pin assemblies for use in a safe and...fuzes for a rotating projectile. A pin, porous disc, return spring, floating O-ring, and sleeve comprise the selected damped set-back pin assembly

The Coast Artillery Journal. Volume 57, Number 3, September 1922

DTIC Science & Technology

1922-09-01

program is available here. The big games are basket-ball and baseball. The Army and Xavy have a fine baseball league. Rugby football is popular with...Panama are largely confined to the Union and Century Clubs, also the National and Ce- cilia Theatres. The Union Club is a Panamanian club that extends...in some, has a screw thread. Fuzes of iron or copper were in use before Langside, some of them screwed. They appear to have contained a match of

German Explosive Ordnance (Projectiles and Projectile Fuzes)

DTIC Science & Technology

1953-03-01

CAP IGNITER BRIDGE INSULATION BLACK POWDER Figure 320—Electric Primers c/12nA and c/22 354 PROJECTILES 0.75 inch, length of body. 0.281 inch...of lip. 0.75 inch, length of body. Number of threads, 5 RH. CONSTRUCTION. The primer houses an igniter bridge which consists of lead styphnate...dipped in gelatin. This bridge has a resistance of approxi- mately 2.2 ohms and is in the circuit with the in- sulated contact plug, the spring washer

Atmospheric Effects upon Laser Beam Propagation: An Annotated Bibliography

DTIC Science & Technology

1979-02-14

pp. 2711-2720, September 1978. [ Measurements in long path white cell and spietro- phone using a tunable DF laser on normal and deuterium depleted...34Backscatter in Clouds at 0.9 pm and Its Effect on Optical Fuzing Systems ," Proc. 7th Laser Conf., Vol. I1, p. 15, June 1976. [ Measured extinction and...relative transmission measurements during March at the White Sands HELSTF (High Energy Laser Standard Test 12 Facility) 6.5 km path . In May they are

History of the Shaped Charge Effect: The First 100 Years

DTIC Science & Technology

1990-03-22

patent, wave shapers, follow-through, U.S. 1949 39 6.5-in. ATAR HEAT rocket, U.S. NOTS, 1950 (schematic) 40 Test of 15-in. long standoff shaped charge...Swiss chemist Frederick Schoenbein in 1845, and nitroglycerin, derived by Ascanio Sobrero, professor of Chemistry at the University of Turin, Italy, in...totally new warhead and fuze system and delivery of the first 1000 rounds to Korea in less than 20 days! The 6.5-Inch ATAR (Code Name "RAM") The 6.5

Human Impact of Technological Innovation on the Battlefield

DTIC Science & Technology

1985-03-15

C-2147 •~4. .. i" Va• LýCTE T.N. Dupuy Associates , Inc. (TNDA) •\\L T P.O. Box 157 JU 12 935 Dunn Loring, Virginia 22027 J 2 ___- Approved for public...ADORESS 10. PROGRAM ELEMENT. PROJECT, TASKA tEA I WORK UNiT NUMU RS T.N. Dupuy Associates , Inc. (TNDA) 62777A.3E162777A879.AA.009 P.O. Box 157 Dunn...proximity fuze, Beehive round, improved II. ASSTRACT (Cointlne an reverse side II necesaery aid Idenlify by block number) The study examines the

Job Aid Manuals for Phase I-ANALYZE of the Instructional systems Development Model

DTIC Science & Technology

1980-05-01

with thuTb amd index Pinchinq nose shut finger. pre ents air leakage 7.2 Use hand to exert pressure on fore- head to maintain backward head tilt. 8...ALlMEE Prep tiol /o- Firi . (1) Turn the slot in the striker (at the nose of the frze) to Mine with the SQ index or the D index on the fuze body...12 Index and Description of Army Training Devices Good * Course materials: Correspondance course lessons and materials used in Good resident courses

Prove Out of Automated Assembly Line for M564 Delay Arming Mechanisms by Acquisition of 40,000 Units Assembled by Automated Line.

DTIC Science & Technology

1981-01-22

Arsenal Contract DUAA25-69-C- 0301 dated 3-10-69 for "Services to design and develop an automated line for assembly of Safety Adapter, Fuze, 1564...determine the line will function at the design rate of 5,000 acceptable assemblies per day and collect production data for incorporation into final...0,000 M564 Delay Arming Mechanisms of the line: Determine that the line will function at the design rate of 5,000. acceotabie asswml I es/day. Collect

Distributed Simulation Testing for Weapons System Performance of the F/A-18 and AIM-120 AMRAAM

DTIC Science & Technology

1998-01-01

Support Facility (WSSF) at China Lake, CA and the AIM-120 Hardware in the Loop (HWIL) laboratory at Point Mugu, CA. The link was established in response to...ROCKET MOTOR TARGET DETECTION (FUZE) SEEKERIASSEMBLYWAH D . ANTENN ’ A TRA-kN.SiV, ITfrER’I" ACTUATOR ELECTRONICS DATA LIX -K PARAMETERS ADIMI20AI AIMI...test series. 3.2 Hardware in the Loop : The AMRAAM Hardware-In-the- Loop (HWIL) lab located at the Naval Air Warfare Center in Point Mugu, CA provides

Conceptual Design of a Basic Production Facility for the XM587E2/XM724 Electronic Time Fuzes

DTIC Science & Technology

1977-11-01

blue side up, and then staked. The spri.ng pin is pressed in position and probed for the 1. 644-0. 010- inch dimension. See figure 33. 4.6.7.2 Parts...fitting subassembly. The detonator 69 IDLE HOPPER FEED -PROBE STAKE SPRING PIN PROBE PRESENCE STAKE LEADL IPROB LEADID ~ ASSEMBLY14 3 1 BLUE SIDE UP...automatic shutoffs. * Warning lights /alarms/ signs /’Jecals where necessary. * Electrical grounding of machine. [ 98 0 Noise levels below 85 decibals at

German Electrical Time and Impact Fuzes and Components

DTIC Science & Technology

1945-09-24

6) The tube w ,s evacuated to 10 mn of mercury . -22- 11. Tubes Ueed in Slectrie^.l Time FVLZCB (Cont’d). (7) Tht leftds wore...discharge took place; the tune was then sealed off. The nrcssuro was usually 10 to 15 run of mercury . -23- t 0̂ — C - CAT/-/0£ <r z>/0£>£’ tjs...radioactive material (fine sulphide ) about 10 ram long and 1 mm wide was made on the outside of the, tube. (9) The tube wos dipped in a rTraphito

Microelectromechanical safing and arming apparatus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koehler, David R; Hoke, Darren A; Weichman, Louis S

2006-05-30

A two-stage acceleration sensing apparatus is disclosed which has applications for use in a fuze assembly for a projected munition. The apparatus, which can be formed by bulk micromachining or LIGA, can sense acceleration components along two orthogonal directions to enable movement of a shuttle from an "as-fabricated" position to a final position and locking of the shuttle in the final position. With the shuttle moved to the final position, the apparatus can perform one or more functions including completing an explosive train or an electrical switch closure, or allowing a light beam to be transmitted through the device.

Microelectromechanical safing and arming apparatus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koehler, David R; Hoke, Darren A; Weichman, Louis S

2008-06-10

A two-stage acceleration sensing apparatus is disclosed which has applications for use in a fuze assembly for a projected munition. The apparatus, which can be formed by bulk micromachining or LIGA, can sense acceleration components along two orthogonal directions to enable movement of a shuttle from an "as-fabricated" position to a final position and locking of the shuttle in the final position. With the shuttle moved to the final position, the apparatus can perform one or more functions including completing an explosive train or an electrical switch closure, or allowing a light beam to be transmitted through the device.

Target-classification approach applied to active UXO sites

NASA Astrophysics Data System (ADS)

Shubitidze, F.; Fernández, J. P.; Shamatava, Irma; Barrowes, B. E.; O'Neill, K.

2013-06-01

This study is designed to illustrate the discrimination performance at two UXO active sites (Oklahoma's Fort Sill and the Massachusetts Military Reservation) of a set of advanced electromagnetic induction (EMI) inversion/discrimination models which include the orthonormalized volume magnetic source (ONVMS), joint diagonalization (JD), and differential evolution (DE) approaches and whose power and flexibility greatly exceed those of the simple dipole model. The Fort Sill site is highly contaminated by a mix of the following types of munitions: 37-mm target practice tracers, 60-mm illumination mortars, 75-mm and 4.5'' projectiles, 3.5'', 2.36'', and LAAW rockets, antitank mine fuzes with and without hex nuts, practice MK2 and M67 grenades, 2.5'' ballistic windshields, M2A1-mines with/without bases, M19-14 time fuzes, and 40-mm practice grenades with/without cartridges. The site at the MMR site contains targets of yet different sizes. In this work we apply our models to EMI data collected using the MetalMapper (MM) and 2 × 2 TEMTADS sensors. The data for each anomaly are inverted to extract estimates of the extrinsic and intrinsic parameters associated with each buried target. (The latter include the total volume magnetic source or NVMS, which relates to size, shape, and material properties; the former includes location, depth, and orientation). The estimated intrinsic parameters are then used for classification performed via library matching and the use of statistical classification algorithms; this process yielded prioritized dig-lists that were submitted to the Institute for Defense Analyses (IDA) for independent scoring. The models' classification performance is illustrated and assessed based on these independent evaluations.

AMMRC (Army Materials and Mechanics Research Center) Mobile Accelerator Neutron Radiography System Operations at U.S. Army Yuma Proving Ground.

DTIC Science & Technology

1984-04-15

are left to right, M739 , M564, and M577 fuzes. Although the * "image is not as sharp as is possible, due to the low L/D (18) and a slight misalignment...of the specimens (see Figure 16N for example), several components/parts are shown on the NR which would not be imaged on the X-rays. In the M739 such...POINT DETONATING: M739 CRS AR iOiR ASS SETTNG SEEVEASSYHIM Figure ~ ~ ~ ~ ~ ~ HOE INA CRSDigasofAR itDtnaigFz S AASYBOY OLE A35 %E ILL 0 0 -- Y, zaZ

XM587E2/XM724 Electronic Time Fuzes: Developmental Test/Operational Test (DT/OT) II Test Phase

DTIC Science & Technology

1979-11-01

unit - da.- aged setbac* spring Sunit - damAged setback pia 140 .4 C) Twenty-five units were subjected to variable testing "to determine tho G level...SAXIP ACCEPT REJECT NO. Ttf7l KSCRIFTI( AG sin4 go flj-. cEI~ *S-FOOTMOP TEsT o 0 (DROPPED IN FIVE DIFFRNT csIllvrATIaNS -- 1 PER OCRIMP... ascue bya i i*ctet FAILURE AND ACTION REPORT 71134 Jj 7113 .I ,...,-... 7 wow o ft.-I I The unIt will not tht. bte the the scalet inpf t to the.uner h

Study of Fuze Structure and Reliability Design Based on the Direct Search Method

NASA Astrophysics Data System (ADS)

Lin, Zhang; Ning, Wang

2017-03-01

Redundant design is one of the important methods to improve the reliability of the system, but mutual coupling of multiple factors is often involved in the design. In my study, Direct Search Method is introduced into the optimum redundancy configuration for design optimization, in which, the reliability, cost, structural weight and other factors can be taken into account simultaneously, and the redundant allocation and reliability design of aircraft critical system are computed. The results show that this method is convenient and workable, and applicable to the redundancy configurations and optimization of various designs upon appropriate modifications. And this method has a good practical value.

Malfunction Investigation of the XM935 Point Detonating Fuze

DTIC Science & Technology

1977-04-01

1 PSK* UNCHANGED FUMLY AR! 2 PSM UNCHANGED FULLY ARMED 3 OK PS4 UNCHANGD 4 CK P24 UNC DNGED 5 PSK (more than S.Q. Det Edge Visible FuLLY AP1M other...Continued) F= NO. DRC NO. 1 2 3 4 5 6 7 8 9 10 3 PSK UNCH UNCH UNCE SEE SQ UNCH UNCH UNCH UNCH UN1H 4 PS4 UNCH SKH E SQ UNCH tNCH UNCH UNCH U2 L!CH...EDGE 5 PS UNCH tCH SE SQ UNCH MMH UNCH UNCH UWCH WECH 6 P4M UNCH UNCH Q SEE SQ EDGE 7 PSK UNCH UNCH SEE SO WXC EDGE a P UNCP L4 UNCH SC E SQ 9 PS4 UNCX

Department of the Army Justification of Estimates for Fiscal Year 1983. Submitted to Congress February 1982.

DTIC Science & Technology

1982-02-01

6.040 0.90 U 1-98 0 62120A FUZE/NUCLEAR WPNS EFFECTS /FLUIDICS 3 G.763 0.223 8,532 11.363 U [-105 O 62201A AIRCRAFT WEAPONS TE1CHNOLOGY 3 1,060 2.004...HUMAN FACTORS ENOR IN SYS DEV I 7.005 0.547 9.173 11.400 U 1-2)6 27 62717A HMRIAN PERFORMANCE EFFECT .’SIMJULATION I 3.196 3,373 3,581 4.360 U j-241 26...62710A MOBILITY AND WEAPONS EFFECTS TECH I5.251 6,260 6.410 9.402 U -245 29 62720A ENVIRONPOENTAL DUALITY TECH 6,437 7,493 6.706 9,627 u 1-251 30 02722A

Analysis of a digital RF memory in a signal-delay application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jelinek, D.A.

1992-03-01

Laboratory simulation of the approach of a radar fuze towards a target is an important factor in our ability to accurately measure the radar's performance. This simulation is achieved, in part, by dynamically delaying and attenuating the radar's transmitted pulse and sending the result back to the radar's receiver. Historically, the device used to perform the dynamic delay has been a limiting factor in the evaluation of a radar's performance and characteristics. A new device has been proposed that appears to have more capability than previous dynamic delay devices. This device is the digital RF memory. This report presents themore » results of an analysis of a digital RF memory used in a signal-delay application. 2 refs.« less

Symposium on Explosives and Pyrotechnics, 13th, Hilton Head Island, SC, Dec. 2-4, 1986, Proceedings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-01-01

The present conference on explosive and pyrotechnic technologies discusses the shock-sensitivity of RDX, the thermodynamic properties of RDX, TNT, nitroglycerine, and HMX energetic molecules, the dynamic resistivity of exploding conductors, the decomposition of azides, the critical shock-initiation energy of emulsion explosives, actuator valve optimization, pyrotechnic aerosolization from novel imbibed liquid matrices, tetrazole initiators, and polymeric binders for red phosphorus pellets. Also discussed are channel-effect studies, the dynamic desensitization of coal mine explosives, the electromagnetic and electrostatic protection of explosives, the reliability of fuze explosive trains, the hazardous properties of explosive chemicals, the emulsification of an explosive with a chemical foamingmore » agent, and low energy ignition of HMX using a foil bridge.« less

Analysis of a digital RF memory in a signal-delay application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jelinek, D.A.

1992-03-01

Laboratory simulation of the approach of a radar fuze towards a target is an important factor in our ability to accurately measure the radar`s performance. This simulation is achieved, in part, by dynamically delaying and attenuating the radar`s transmitted pulse and sending the result back to the radar`s receiver. Historically, the device used to perform the dynamic delay has been a limiting factor in the evaluation of a radar`s performance and characteristics. A new device has been proposed that appears to have more capability than previous dynamic delay devices. This device is the digital RF memory. This report presents themore » results of an analysis of a digital RF memory used in a signal-delay application. 2 refs.« less

Planar LTCC transformers for high voltage flyback converters: Part II.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schofield, Daryl; Schare, Joshua M., Ph.D.; Slama, George

This paper is a continuation of the work presented in SAND2007-2591 'Planar LTCC Transformers for High Voltage Flyback Converters'. The designs in that SAND report were all based on a ferrite tape/dielectric paste system originally developed by NASCENTechnoloy, Inc, who collaborated in the design and manufacturing of the planar LTCC flyback converters. The output/volume requirements were targeted to DoD application for hard target/mini fuzing at around 1500 V for reasonable primary peak currents. High voltages could be obtained but with considerable higher current. Work had begun on higher voltage systems and is where this report begins. Limits in material propertiesmore » and processing capabilities show that the state-of-the-art has limited our practical output voltage from such a small part volume. In other words, the technology is currently limited within the allowable funding and interest.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peglow, S.G.

We feel that the concept of intercepting a fractionated threat from a tactical ballistic missile is potentially feasible and would have very high payoff for the defense. Many other concepts have been suggested to solve this problem, although they have mostly been more futuristic approaches, e.g. aircrafty based lasers. We also believe that current technologies are not likely to be adequate for the expected types of very small submunition payloads, especially in the presence of relatively simple countermeasures. The MEDUSA concept, or its clones, may very well provide a vehicle for the study of less stressing threats, e.g. separating warheadsmore » and provide a lethality enhancement for non-deployed payloads. An opportunity also exists to investigate alternative technologies, such as the explosively-formed ``disk`` idea. The use of high-precision, limited field-of-view sensor-fuzed munitions is a subject of interest in other Defense Department programs and may have application to the important area of theater missile defense.« less

Munitions Classification Library Update and Expansion Data Collection Report: Camp Lejeune and Eglin

DTIC Science & Technology

2015-10-09

Motor 4.5-in T160ES HE R N N N N W without Motor Rocket Motor R N N N N W 66mm M72A1 R Y Y N N U with Coupler and Motor ...66mm M74 R N Y N N W with Motor 3.5-in M30A1 R Y Y N N W WP Smoke with M405 Dummy Fuze and Motor Rocket Motor R Y N N N W 3.5-in M30A1 R N Y N N...N U/P with Motor without Fins 2.36-in M6 R Y Y N N U/P with Motor with Fins Rocket Motor R Y Y N N U/P 2.36-in M6 R N N N N U/P Rifle

Fuze for explosive magnetohydrodynamic generator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webb, G.

1976-12-23

An apparatus is examined by which high explosive charges are propelled into and detonated at the center of an MHD-X generator. The high explosive charge units are engaged and propelled by a reciprocating ram device. Detonating in each instance is achieved by striking with a firing pin a detonator charge that is in register with a booster charge, the booster charge being in detonating communication with the high explosive charge. Various safety requirements are satisfied by a spring loaded slider operating in a channel transverse and adjacent to the booster charge. The slide retains the detonator charge out of registermore » with the booster charge until a safety pin that holds the slider in place is pulled by a lanyard attached between the reciprocating ram and the safety pin. Removal of the safety pin permits the detonator charge to slide into alignment with the booster charge. Firing pin actuation is initiated by the slider at the instant the detonator charge and the booster charge come into register.« less

High Frequency Supercapacitors for Piezo-based Energy Harvesting

NASA Astrophysics Data System (ADS)

Ervin, Matthew; Pereira, Carlos; Miller, John; Outlaw, Ronald; Rastegar, Jay; Murray, Richard

2013-03-01

Energy harvesting is being investigated as an alternative to batteries for powering munition guidance and fuzing functions during flight. A piezoelectric system that generates energy from the oscillation of a mass on a spring (set in motion by the launch acceleration) is being developed. Original designs stored this energy in an electrolytic capacitor for use during flight. Here we replace the electrolytic capacitor with a smaller, lighter, and potentially more reliable electrochemical double layer capacitor (aka, supercapacitor). The potential problems with using supercapacitors in this application are that the piezoelectric output greatly exceeds the supercapacitor electrolyte breakdown voltage, and the frequency greatly exceeds the operating frequency of commercial supercapacitors. Here we have investigated the use of ultrafast vertically oriented graphene array-based supercapacitors for storing the energy in this application. We find that the electrolyte breakdown is not a serious limitation as it is either kinetically limited by the relatively high frequency of the piezoelectric output, or it is overcome by the self-healing nature of supercapacitors. We also find that these supercapacitors have sufficient dynamic response to efficiently store the generated energy.

Remedial Design/Remedial Action Work Plan for Operable Units 6-05 and 10-04, Phase IV

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. P. Wells

2006-11-14

This Phase IV Remedial Design/Remedial Action Work Plan addresses the remediation of areas with the potential for UXO at the Idaho National Laboratory. These areas include portions of the Naval Proving Ground, the Arco High-Altitude Bombing Range, and the Twin Buttes Bombing Range. Five areas within the Naval Proving Ground that are known to contain UXO include the Naval Ordnance Disposal Area, the Mass Detonation Area, the Experimental Field Station, The Rail Car Explosion Area, and the Land Mine Fuze Burn Area. The Phase IV remedial action will be concentrated in these five areas. For other areas, such as themore » Arco High-Altitude Bombing Range and the Twin Buttes Bombing Range, ordnance has largely consisted of sand-filled practice bombs that do not pose an explosion risk. Ordnance encountered in these areas will be addressed under the Phase I Operations and Maintenance Plan that allows for the recovery and disposal of ordnance that poses an imminent risk to human health or the environment.« less

Slow fuze on the neutron bomb

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frye, A.

The U.S. government has wrestled with the neutron bomb's production and its potential bargaining powers for years. President Carter's decision not to decide about the neutron bomb has now provoked a furor. The alarm focuses more on the politics of the decision than on its moral, military, and strategic aspects. The political reaction to Carter's deferring production may virtually compel him to produce neutron warheads eventually, unless the Soviet Union displays compensating restraint in the coming months. While the Kremlin has indicated a willingness to forgo production of similar weapons of its own, it is unlikely to accept American demandsmore » for other concessions, such as a limit on Soviet SS-20 missile deployments. Since the issue has not been settled, but merely postponed, further thought should be given to the potential costs and benefits of an eventual deployment. Following a lengthy discussion of all aspects of the issue, the answers for the use of the neutron bomb and as to whether it will make Europe and America more secure remain unanswered. (MCW)« less

A Reactor Development Scenario for the FUZE Shear-flow Stabilized Z-pinch

NASA Astrophysics Data System (ADS)

McLean, H. S.; Higginson, D. P.; Schmidt, A.; Tummel, K. K.; Shumlak, U.; Nelson, B. A.; Claveau, E. L.; Golingo, R. P.; Weber, T. R.

2016-10-01

We present a conceptual design, scaling calculations, and a development path for a pulsed fusion reactor based on the shear-flow-stabilized Z-pinch device. Experiments performed on the ZaP device have demonstrated stable operation for 40 us at 150 kA total discharge current (with 100 kA in the pinch) for pinches that are 1cm in diameter and 100 cm long. Scaling calculations show that achieving stabilization for a pulse of 100 usec, for discharge current 1.5 MA, in a shortened pinch 50 cm, results in a pinch diameter of 200 um and a reactor plant Q 5 for reasonable assumptions of the various system efficiencies. We propose several key intermediate performance levels in order to justify further development. These include achieving operation at pinch currents of 300 kA, where Te and Ti are calculated to exceed 1 keV, 700 kA where fusion power exceeds pinch input power, and 1 MA where fusion energy per pulse exceeds input energy per pulse. This work funded by USDOE ARPAe ALPHA Program and performed under the auspices of Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-697801.

Thermal batteries: A technology review and future directions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guidotti, R.A.

Thermally activated (``thermal``) batteries have been used for ordnance applications (e.g., proximity fuzes) since World War II and, subsequent to that, in nuclear weapons. This technology was developed by the Germans as a power source for their V2 rockets. It was obtained by the Allies by interrogation of captured German scientists after the war. The technology developed rapidly from the initial primitive systems used by the Germans to one based on Ca/CaCrO{sub 4}. This system was used very successfully into the late 1970s, when it was replaced by the Li-alloy/FeS{sub 2} electrochemical system. This paper describes the predominant electrochemical couplesmore » that have been used in thermal batteries over the years. Major emphasis is placed on the chemistry and electrochemistry of the Ca/CaCrO{sub 4} and Li-alloy/FeS{sub 2} systems. The reason for this is to give the reader a better appreciation for the advances in thermal-battery technology for which these two systems are directly responsible. Improvements to date in the current Li-alloy/FeS{sub 2} and related systems are discussed and areas for possible future research and development involving anodes, cathodes, electrolytes, and insulations are outlined. New areas where thermal-battery technology has potential applications are also examined.« less

Open-Loop Flight Testing of COBALT GN&C Technologies for Precise Soft Landing

NASA Technical Reports Server (NTRS)

Carson, John M., III; Amzajerdian, Farzin; Seubert, Carl R.; Restrepo, Carolina I.

2017-01-01

A terrestrial, open-loop (OL) flight test campaign of the NASA COBALT (CoOperative Blending of Autonomous Landing Technologies) platform was conducted onboard the Masten Xodiac suborbital rocket testbed, with support through the NASA Advanced Exploration Systems (AES), Game Changing Development (GCD), and Flight Opportunities (FO) Programs. The COBALT platform integrates NASA Guidance, Navigation and Control (GN&C) sensing technologies for autonomous, precise soft landing, including the Navigation Doppler Lidar (NDL) velocity and range sensor and the Lander Vision System (LVS) Terrain Relative Navigation (TRN) system. A specialized navigation filter running onboard COBALT fuzes the NDL and LVS data in real time to produce a precise navigation solution that is independent of the Global Positioning System (GPS) and suitable for future, autonomous planetary landing systems. The OL campaign tested COBALT as a passive payload, with COBALT data collection and filter execution, but with the Xodiac vehicle Guidance and Control (G&C) loops closed on a Masten GPS-based navigation solution. The OL test was performed as a risk reduction activity in preparation for an upcoming 2017 closed-loop (CL) flight campaign in which Xodiac G&C will act on the COBALT navigation solution and the GPS-based navigation will serve only as a backup monitor.

U.S. Army Corrosion Office's storage and quality requirements for military MEMS program

NASA Astrophysics Data System (ADS)

Zunino, J. L., III; Skelton, D. R.

2007-04-01

As the Army transforms into a more lethal, lighter and agile force, the technologies that support these systems must decrease in size while increasing in intelligence. Micro-electromechanical systems (MEMS) are one such technology that the Army and DOD will rely on heavily to accomplish these objectives. Conditions for utilization of MEMS by the military are unique. Operational and storage environments for the military are significantly different than those found in the commercial sector. Issues unique to the military include; high G-forces during gun launch, extreme temperature and humidity ranges, extended periods of inactivity (20 years plus) and interaction with explosives and propellants. The military operational environments in which MEMS will be stored or required to function are extreme and far surpass any commercial operating conditions. Security and encryption are a must for all MEMS communication, tracking, or data reporting devices employed by the military. Current and future military applications of MEMS devices include safety and arming devices, fuzing devices, various guidance systems, sensors/detectors, inertial measurement units, tracking devices, radio frequency devices, wireless Radio Frequency Identifications (RFIDs) and network systems, GPS's, radar systems, mobile base systems and information technology. MEMS embedded into these weapons systems will provide the military with new levels of speed, awareness, lethality, and information dissemination. The system capabilities enhanced by MEMS will translate directly into tactical and strategic military advantages.

A Miniaturized Magnetic Induction Sensor Using Geomagnetism for Turn Count of Small-Caliber Ammunition

PubMed Central

Yoon, Sang-Hee; Lee, Seok-Woo; Lee, Young-Ho; Oh, Jong-Soo

2006-01-01

This paper presents a miniaturized magnetic induction sensor (MMIS), where geomagnetism and high rpm rotation of ammunition are used to detect the turn number of the ammunition for applications to small-caliber turn-counting fuzes. The MMIS, composed of cores and a coil, has a robust structure without moving parts to increase the shock survivability in a gunfire environment of ∼30,000 g's. The MMIS is designed and fabricated on the basis of the simulation results of an electromagnetic analysis tool, Maxwell® 3D. In the experimental study, static MMIS test using a solenoid-coil apparatus and dynamic MMIS test (firing test) have been made. The present MMIS has shown that an induction voltage of 6.5 mVp-p is generated at a magnetic flux density of 0.05 mT and a rotational velocity of 30,000 rpm. From the measured signal, MMIS has shown a signal-to-noise ratio of 44.0 dB, a nonlinearity of 0.59%, a frequency-normalized sensitivity of 0.256±0.010 V/T·Hz and a drift of 0.27% in the temperature range of -30∼+43°C. Firing test has shown that the MMIS can be used as a turn-counting sensor for small-caliber ammunition, verifying the shock survivability of the MMIS in a high-g environment.

Rail damage in a solid-armature rail gun. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brassard, T.; Homan, C.G.

1987-12-01

Plasma-arc-drive rail guns operate by forming a high-temperature plasma behind the projectile using a thin metal fuze. These systems achieve the highest projectile velocities (about 12 km /sec), since the driving force includes a substantial plasma pressure as well as the electromagnetic or Lorentz force. Unfortunately, severe rail damage occurs primarily from the intense temperatures generated by the plasma arc and the wiping motion of the armature itself. The solid-armature gun replaces the plasma armature with a conducting metal armature. Since the plasma arcing is reduced or eliminated, the projectiles are accelerated mainly by the Lorentz force. Thus, solid armaturemore » rail guns operate at lower projectile velocities. The important tradeoff is that there is a substantial reduction in rail damage for metal armature projectiles. The elimination of the plasma force limits projectile velocities in the metal-armature rail guns. A more-subtle limit is the speed at which the commutation process can take place. Although the latter limit is still not well understood, experimental evidence indicates a commutation limit may occur near 6 to 7 km/sec. This velocity limit is still attractive for Army tactical missions for rail guns. The actual rail damage occurring with two types of metal armatures, wire brush contactors and monolithic metal contactors, and new developments in barrel technology, such as superconducting augmentation, are presented in this report.« less

Inexpensive semi-autonomous ground vehicles for defusing IEDs

NASA Astrophysics Data System (ADS)

Davenport, Chris; Lodmell, James; Womble, Phillip C.; Barzilov, Alexander; Paschal, Jon; Hernandez, Robert; Moss, Kyle T.; Hopper, Lindsay

2008-04-01

Improvised explosive devices (IEDs) are an important concern to coalition forces during the conflicts in the Middle East. These devices are responsible for many casualties to American armed forces in the Middle East. These explosives are particularly dangerous because they are improvised with materials readily available to the designer, and there is no systematic way of explosive ordinance disposal. IEDs can be made from things such as standard military ammunition and can be detonated with common electronic devices such as cell phones and garage door openers. There is a great need for a low cost solution to neutralize these IEDs. At the Applied Physics Institute we are building a single function disrupter robot whose sole purpose is to neutralize these IEDs. We are modifying a toy remote control car to control it either wirelessly using WI-FI (IEEE 802.11) or wired by tethering the vehicle with an Ethernet cable (IEEE 802.3). The robot will be equipped with a high velocity fuze disrupter to neutralize the IED as well as a video camera for inspection and aiming purposes. This robot utilizes commercial-off-the-shelf (COTS) components which keeps the cost relatively low. Currently, similar robot systems have been deployed in Iraq and elsewhere but their method of operation is such that it is impractical to use in non-combat situations. We will discuss our design and possible deployment scenarios.

Analytical investigation of AlCl[3]/SO[2]Cl[2] catholyte materials for secondary fuze reserve batteries.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Butler, Paul Charles; Rodriguez, Mark Andrew; Segall, Judith M.

2004-05-01

Exploration of the fundamental chemical behavior of the AlCl{sub 3}/SO{sub 2}Cl{sub 2} catholyte system for the ARDEC Self-Destruct Fuze Reserve Battery Project under accelerated aging conditions was completed using a variety of analytical tools. Four different molecular species were identified in this solution, three of which are major. The relative concentrations of the molecular species formed were found to depend on aging time, initial concentrations, and storage temperature, with each variable affecting the kinetics and thermodynamics of this complex reaction system. We also evaluated the effect of water on the system, and determined that it does not play a rolemore » in dictating the observed molecular species present in solution. The first Al-containing species formed was identified as the dimer [Al({mu}-Cl)Cl{sub 2}]{sub 2}, and was found to be in equilibrium with the monomer, AlCl{sub 3}. The second species formed in the reaction scheme was identified by single crystal X-ray diffraction studies as [Cl{sub 2}Al({mu}-O{sub 2}SCl)]{sub 2} (I), a scrambled AlCl{sub 3}{center_dot}SO{sub 2} adduct. The SO{sub 2}(g) present, as well as CL{sub 2}(g), was formed through decomposition of SO{sub 2}CL{sub 2}. The SO{sub 2}(g) generated was readily consumed by AlCl{sub 3} to form the adduct 1 which was experimentally verified when 1 was also isolated from the reaction of SO{sub 2}(g) and AlCl {sub 3}. The third species found was tentatively identified as a compound having the general formula {l_brace}[Al(O)Cl{sub 2}][OSCl{sub 2}]{r_brace}{sub n}. This was based on {sup 27}Al NMR data that revealed a species with tetrahedrally coordinated Al metal centers with increased oxygen coordination and the fact that the precipitate, or gel, that forms over time was shown by Raman spectroscopic studies to possess a component that is consistent with SOCl{sub 2}. The precursor to the precipitate should have similar constituents, thus the assignment of {l_brace}[Al(O)Cl{sub 2}][OSCl{sub 2}]{r_brace}{sub n}. The precipitate was further identified by solid state {sup 27}Al MAS NMR data to possess predominantly octahedral A1 metal center which implies {l_brace}[Al(O)Cl{sub 2}][OSCl{sub 2}]{r_brace}{sub n} must undergo some internal rearrangements. A reaction sequence has been proposed to account for the various molecular species identified in this complex reaction mixture during the aging process. The metallurgical welds were of high quality. These results were all visually determined there was no mechanical testing performed. However, it is recommended that the end plate geometry and weld be changed. If the present weld strength, based on .003' - .005' penetration, is sufficient for unit performance, the end plate thickness can be reduced to .005' instead of the .020' thickness. This will enable the plug to be stamped so that it can form a cap rather than a plug and solve existing problems and increase the amount of catholyte which may be beneficial to battery performance.« less

Survey of Lake Ontario bottom sediment off Rochester, New York, to define the extent of jettisoned World War II material and its potential for sediment contamination

USGS Publications Warehouse

Kennedy, Gregory; Kappel, William M.

2000-01-01

Military-type mat??riel was recovered from the bottom of Lake Ontario near Rochester, N.Y., during bottom-trawl, fish-stock surveys at depths of 75 to 180 feet each year from 1978 through 1996. The recovered mat??riel included many shell-detonator nose cones (2 inches in diameter by about 3.5 inches long); several electronic components; one corroded box of detonators; a corrugated container of mercury-filled capsules; and corroded batteries. Most of the recovered mat??riel has been identified as defective components of shell detonators (proximity-fuze assemblies) that were jettisoned in the lake to protect them from discovery during World War II. Side-scan SONAR, metal-detector, and ROV (remotely-operated-vehicle) surveys found no evidence of any large piles of mat??riel containing potentially hazardous, toxic, or polluting materials within the 17-square-mile study site. Many scattered magnetic anomalies were detected in this area, but chemical analysis of bottom sediment and of zebra- and quagga-mussel (Dreissena spp.) tissue indicate that the concentrations of mercury and other heavy metals are within the previously documented ranges for Lake Ontario sediment. The failure of ROV videos and of SCUBA-diver surveys and probes of the lake bottom to locate any debris indicates that most, if not all, of the debris is scattered and buried under a layer of fine-grained sediment and, possibly, mussels.

200 kj copper foil fuses. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

McClenahan, C.R.; Goforth, J.H.; Degnan, J.H.

1980-04-01

A 200-kJ, 50-kV capacitor bank has been discharged into 1-mil-thick copper foils immersed in fine glass beads. These foils ranged in length from 27 to 71 cm and in width from 15 to 40 cm. Voltage spikes of over 250 kV were produced by the resulting fuse behavior of the foil. Moreover, the current turned off at a rate that was over 6 times the initial bank dI/dt. Full widths at half maxima for the voltage and dI/dt spikes were about 0.5 microsec, with some as short as 300 nanosec. Electrical breakdown was prevented in all but one size fuzemore » with maximum applied fields of 7 kV/cm. Fuses that were split into two parallel sections have been tested, and the effects relative to one-piece fuses are much larger than would be expected on the basis of inductance differences alone. A resistivity model for copper foil fuses, which differs from previous work in that it includes a current density dependence, has been devised. Fuse behavior is predicted with reasonable accuracy over a wide range of foil sizes by a quasi-two-dimensional fuse code that incorporates this resistivity model. A variation of Maisonnier's method for predicting optimum fuze size has been derived. This method is valid if the risetime of the bank exceeds 3 microsec, in which case it can be expected to be applicable over a wide range of peak current densities.« less

Radar echo from a flat conducting plate - near and far

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, C.S.

1982-01-01

Over certain types of terrain, a radar fuze (or altimeter), by virtue of the horizontal component of its velocity, is likely to pass over various flat objects of limited size. The echo from such objects could have a duration less than that of one Doppler cycle, where the Doppler frequency is due to the vertical component of the velocity. If the terrain is principally made up of such objects, their echoes are in most cases entirely uncorrelated with each other. Hence, the total echo after mixing at the radar with the delayed transmitted wave would have a noise-like spectrum notmore » at all confined to the Doppler-frequency band where the desired echo signal is expected. This would seriously degrade the performance of a radar that utilizes correlation. This work shows that the echo from a square flat plate will be of duration greater than the time it takes to pass over the plate if the height h above it satisfies h > a/sup 2//lambda where a is the plate-edge dimension and lambda is the radar wavelength. The results presented here can be used to determine the spatial region wherein the echo exists, and the magnitude and phase of the echo from such a plate. I infer from these results that the case where the signal has a noise-like spectrum is not impossible but it is unlikely for the applications with which I am familiar.« less

The Canadian Forces ILDS: a militarily fielded multisensor vehicle-mounted teleoperated landmine detection system

NASA Astrophysics Data System (ADS)

McFee, John E.; Russell, Kevin L.; Chesney, Robert H.; Faust, Anthony A.; Das, Yogadhish

2006-05-01

The Improved Landmine Detection System (ILDS) is intended to meet Canadian military mine clearance requirements in rear area combat situations and peacekeeping on roads and tracks. The system consists of two teleoperated vehicles and a command vehicle. The teleoperated protection vehicle precedes, clearing antipersonnel mines and magnetic and tilt rod-fuzed antitank mines. It consists of an armoured personnel carrier with a forward looking infrared imager, a finger plow or roller and a magnetic signature duplicator. The teleoperated detection vehicle follows to detect antitank mines. The purpose-built vehicle carries forward looking infrared and visible imagers, a 3 m wide, down-looking sensitive electromagnetic induction detector array and a 3 m wide down-looking ground probing radar, which scan the ground in front of the vehicle. Sensor information is combined using navigation sensors and custom navigation, registration, spatial correspondence and data fusion algorithms. Suspicious targets are then confirmed by a thermal neutron activation detector. The prototype, designed and built by Defence R&D Canada, was completed in October 1997. General Dynamics Canada delivered four production units, based on the prototype concept and technologies, to the Canadian Forces (CF) in 2002. ILDS was deployed in Afghanistan in 2003, making the system the first militarily fielded, teleoperated, multi-sensor vehicle-mounted mine detector and the first with a fielded confirmation sensor. Performance of the prototype in Canadian and independent US trials is summarized and recent results from the production version of the confirmation sensor are discussed. CF operations with ILDS in Afghanistan are described.

Thermal weapon sights with integrated fire control computers: algorithms and experiences

NASA Astrophysics Data System (ADS)

Rothe, Hendrik; Graswald, Markus; Breiter, Rainer

2008-04-01

The HuntIR long range thermal weapon sight of AIM is deployed in various out of area missions since 2004 as a part of the German Future Infantryman system (IdZ). In 2007 AIM fielded RangIR as upgrade with integrated laser Range finder (LRF), digital magnetic compass (DMC) and fire control unit (FCU). RangIR fills the capability gaps of day/night fire control for grenade machine guns (GMG) and the enhanced system of the IdZ. Due to proven expertise and proprietary methods in fire control, fast access to military trials for optimisation loops and similar hardware platforms, AIM and the University of the Federal Armed Forces Hamburg (HSU) decided to team for the development of suitable fire control algorithms. The pronounced ballistic trajectory of the 40mm GMG requires most accurate FCU-solutions specifically for air burst ammunition (ABM) and is most sensitive to faint effects like levelling or firing up/downhill. This weapon was therefore selected to validate the quality of the FCU hard- and software under relevant military conditions. For exterior ballistics the modified point mass model according to STANAG 4355 is used. The differential equations of motions are solved numerically, the two point boundary value problem is solved iteratively. Computing time varies according to the precision needed and is typical in the range from 0.1 - 0.5 seconds. RangIR provided outstanding hit accuracy including ABM fuze timing in various trials of the German Army and allied partners in 2007 and is now ready for series production. This paper deals mainly with the fundamentals of the fire control algorithms and shows how to implement them in combination with any DSP-equipped thermal weapon sights (TWS) in a variety of light supporting weapon systems.

A Comparison of High-Voltage Switches

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, K.W.; Scott, G.L.

1999-02-01

This report summarizes our work on high-voltage switches during the past few years. With joint funding from the Department of Energy (DOE) and the Department of Defense (DOD), we tested a wide variety of switches to a common standard. This approach permitted meaningful comparisons between disparate switches. Most switches were purchased from commercial sources, though some were experimental devices. For the purposes of this report, we divided the switches into three generic types (gas, vacuum, and semiconductor) and selected data that best illustrates important strengths and weaknesses of each switch type. Test techniques that indicate the state of health ofmore » the switches are emphasized. For example, a good indicator of residual gas in a vacuum switch is the systematic variation of the switching delay in response to changes in temperature and/or operating conditions. We believe that the presentation of this kind of information will help engineers to select and to test switches for their particular applications. Our work was limited to switches capable of driving slappers. Also known as exploding-foil initiators, slappers are detonators that initiate a secondary explosive by direct impact with a small piece of matter moving at the detonation velocity (several thousands of meters per second). A slapper is desirable for enhanced safety (no primary explosive), but it also places extra demands on the capacitor-discharge circuit to deliver a fast-rising current pulse (greater than 10 A/ns) of several thousand amperes. The required energy is substantially less than one joule; but this energy is delivered in less than one microsecond, taking the peak power into the megawatt regime. In our study, the switches operated in the 1 kV to 3 kV range and were physically small, roughly 1 cm{sup 3} or less. Although a fuze functions only once in actual use, multiple-shot capability is important for production testing and for research work. For this reason, we restricted this report to multiple-shot switches. Furthermore, our work included only switches with submicrosecond timing precision, thereby excluding mechanical switches.« less

A Test Study to Display Buried Anti-Tank Landmines with GPR and Research Soil Characteristics with CRS

NASA Astrophysics Data System (ADS)

Kadioglu, Selma; Kagan Kadioglu, Yusuf

2014-05-01

An anti-tank mine (AT mine) is a type of land mine designed to damage or destroy vehicles including tanks and armored fighting vehicles. Anti-tank mines typically have a much larger explosive charge, and a fuze designed only to be triggered by vehicles or, in some cases, tampering with the mine. There are a lot of AT mine types. In our test study, MK4 and MK5 AT mine types has been used. The Mk 5 was a cylindrical metal cased U.K. anti-tank blast mine that entered service in 1943, during the Second World War. General Specifications of them are 203 mm diameter, 127 mm height, 4.4-5.7 kg weight, 2.05-3.75 kg of TNT explosive content and 350 lbs operating pressure respectively. The aims of the test study were to image anti-tank landmine with GPR method and to analyse the soil characteristics before the mines made explode and after made be exploded and determine changing of the soil characteristics. We realized data measurement on the real 6 unexploded anti-tank landmine buried approximately 15 cm in depth. The mines spaced 3 m were buried in two lines. Space between lines was 1.5 m. We gathered data on the profiles, approximately 7 m, with a Ramac CUII system and 800 MHz shielded antenna. We collected soil samples on the mines, near and around the mines, on the area in village. We collected soil samples before exploding and after exploding mines. We imaged anti-tank landmines on the depth slices of the GPR data and in their interactive transparent 3D subsets successfully. We used polarized microscope and confocal Raman spectroscopy (CRS) to identify soil characteristic before and after exploitation. The results presented that GPR method and its 3D imaging were successful to determine AT mines, and there was no important changing on mineralogical and petrographical characterization of the soil before and after exploding processing. This project has been supported by Ankara University under grant no 11B6055002. The study is a contribution to the EU funded COST action TU1208, "Civil Engineering Applications of Ground penetrating Radar".

Mobile Munitions Assessment System Field Capabilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

A. M. Snyder; D. A. Verrill; K. D. Watts

1999-05-27

The US has developed, stored, tested, and conducted disposal operations on various forms of chemical munitions for several decades. The remnants of these activities have resulted in the presence of suspect CWM at more than 200 sites in the US, the District of Columbia, and the US Virgin Islands. An advanced Mobile Munitions Assessment System (Phase II MMAS) has been designed, fabricated, assembled, and tested by the Idaho National Engineering and Environmental Laboratory under contract to the US Army's Project Manager for Non-Stockpile Chemical Materiel for use in the assessment and characterization of ''non-stockpile'' chemical warfare materiel (CWM). The Phasemore » II MMAS meets the immediate need to augment response equipment currently used by the US Army with a system that includes state-of-the-art assessment equipment and advanced sensors. The Phase II MMAS will be used for response to known storage and remediation sites. This system is designed to identify the munition type; evaluate the condition of the CWM; evaluate the environmental conditions in the vicinity of the CWM; determine if fuzes, bursters, or safety and arming devices are in place; identify the chemical fill; provide other data (e.g., meteorological data) necessary for assessing the risk associated with handling, transporting, and disposing of CWM; and record the data on a dedicated computer system. The Phase II MMAS is capable of over-the-road travel and air transport to any site for conducting rigorous assessments of suspect CWM. The Phase II MMAS utilizes a specially-designed commercial motor home to provide a means to transport an interactive network of non-intrusive characterization and assessment equipment. The assessment equipment includes radiography systems, a gamma densitometer system, a Portable Isotopic Neutron Spectroscopy (PINS) system, a Secondary Ion Mass Spectroscopy (SIMS) system, air monitoring equipment (i.e., M-90s and a field ion spectroscopy system), and a phase determination equipment Command and control equipment includes a data acquisition and handling system, two meteorological stations, video equipment, and multiple communication systems. The Phase II MMAS motor home also serves an as environmentally controlled on-site command post for the MMAS operators when deployed. The data developed by the MMAS will be used to help determine the appropriate methods and safeguards necessary to transport, store, and dispose of agent-filled munitions in a safe and environmentally acceptable manner.« less

Optimal Fragmentation and Dispersion of Hazardous Near-Earth Objects

NASA Technical Reports Server (NTRS)

Wie, Bong

2012-01-01

The complex problem of protecting the Earth from the possibility of a catastrophic impact by a hazardous near-Earth object (NEO) has been recently reassessed in [1]. In a letter on NEOs from the White House Office of Science and Technology Policy (OSTP) to the U.S. Senate and Congress in 2010, the White House OSTP strongly recommended that NASA take the lead in conducting research activities for NEO detection, characterization, and deflection technologies. Furthermore, President Obama's new National Space Policy specifically directs NASA to "pursue capabilities, in cooperation with other departments, agencies, and commercial partners, to detect, track, catalog, and characterize NEOs to reduce the risk of harm to humans from an unexpected impact on our planet." The Planetary Defense Task Force of the NASA Advisory Council also recommended that the NASA Office of the Chief Technologist (OCT) begin efforts to investigate asteroid deflection techniques. With national interest growing in the United States, the NEO threat detection and mitigation problem was recently identified as one of NASA's Space Technology Grand Challenges. An innovative solution to NASA's NEO Impact Threat Mitigation Grand Challenge problem was developed through a NIAC Phase I study (9/16/11 - 9/15/12), and it will be further investigated for a NIAC Phase II study (9/10/12 - 9/9/14). Various NEO deflection technologies, including nuclear explosions, kinetic impactors, and slow-pull gravity tractors, have been proposed and examined during the past two decades. Still, there is no consensus on how to reliably deflect or disrupt hazardous NEOs in a timely manner. It is expected that the most probable mission scenarios will have a mission lead time much shorter than 10 years, so the use of nuclear explosives becomes the most feasible method for planetary defense. Direct intercept missions with a short warning time will result in arrival closing velocities of 10-30 kilometers per second with respect to the target asteroid. Given such a large arrival delta V requirement, a rendezvous mission to the target asteroid is infeasible with existing launch vehicles. Furthermore, state-of-the-art penetrating subsurface nuclear explosion technology limits the penetrator's impact velocity to less than approximately 300 meters per second because higher impact velocities prematurely destroy the nuclear fuzing mechanisms. Therefore, significant advances in hypervelocity nuclear interceptor/ penetrator technology must be achieved to enable a last-minute nuclear disruption mission with intercept velocities as high as 30 kilometers per second. Consequently, a HAIV (Hypervelocity Asteroid Intercept Vehicle) mission architecture (Figure 1.1), which blends a hypervelocity kinetic impactor with a subsurface nuclear explosion for optimal fragmentation and dispersion of hazardous NEOs, has been developed through a Phase I study, and it will be further developed and validated through a Phase II study.

Supplemental Environmental Baseline Survey for Proposed Land Use Permit Modification for Expansion of the Dynamic Explosive Test Site (DETS) 9940 Main Complex Parking Lot

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peek, Dennis W.

The “subject property” is comprised of a parcel of land within the Kirtland Military Reservation, Bernalillo County, New Mexico, as shown on the map in Appendix B of this document. The land requirement for the parking lot addition to the 9940 Main Complex is approximately 2.7 acres. The scope of this Supplemental Environmental Baseline Survey (SEBS) is for the parking lot addition land transfer only. For details on the original 9940 Main Complex see Environmental Baseline Survey, Land Use Permit Request for the 9940 Complex PERM/0-KI-00-0001, August 21, 2003, and for details on the 9940 Complex Expansion see Environmental Baselinemore » Survey, Proposed Land Use Permit Expansion for 9940 DETS Complex, June 24, 2009. The 2.7-acre parcel of land for the new parking lot, which is the subject of this EBS (also referred to as the “subject property”), is adjacent to the southwest boundary of the original 12.3- acre 9940 Main Complex. No testing is known to have taken place on the subject property site. The only activity known to have taken place was the burial of overhead utility lines in 2014. Adjacent to the subject property, the 9940 Main Complex was originally a 12.3-acre site used by the Department of Energy (DOE) under a land use permit from the United States Air Force (USAF). Historical use of the site, dating from 1964, included arming, fusing, and firing of explosives and testing of explosives systems components. In the late 1970s and early 1980s experiments at the 9940 Main Complex shifted toward reactor safety issues. From 1983 to 1988, fuel coolant interaction (FCI) experiments were conducted, as were experiments with conventional high explosives (HE). Today, the land is used for training of the Nuclear Emergency Response community and for research on energetic materials. In 2009, the original complex was expanded to include four additional 20-acre areas: 9940 Training South, 9940 Training East, T-Range 6, and Training West Landing Zone. The proposed use of the subject property is for the purpose of adding a parking lot to serve the increase in customer vehicles that is occurring as the 9940 Main Complex is more heavily utilized, and as the 2009 Expansion areas come online as operational training facilities. The subject property would be used only for parking, not for testing or training activities. The parking lot would have a gravel surface. Current and future work at the 9940 Main Complex involves arming, fuzing, and firing of explosives and the testing of explosive systems components in both terrestrial and aquatic settings. It also involves specialized training activities for a variety of first responder customers, both DOE and non-DOE agencies. The approach was to perform a document search, supplemented by a visual site inspection, to identify potential environmental contamination associated with the property. Factors evaluated included hazardous substances; petroleum products and derivatives; environmental restoration sites; areas of concern; storage tanks; oil/water separators; grease traps; wash racks; waste tanks; pesticides; military munitions/ordnance; medical or bio-hazardous waste; radioactive waste; solid/municipal waste; indoor air quality; groundwater; wastewater treatment, collection, and disposal/discharge; drinking water quality; utilities; asbestos; polychlorinated biphenyls (PCBs); radon; lead-based paint; cultural resources; floodplains; and natural/biological resources. Each of these factors is evaluated separately in Section 5, Findings for Subject Property. The property categorization for this subject property would be considered Category 1- “An area or real property where no storage, release, or disposal of hazardous substances or petroleum products or their derivatives has occurred into the environment or structures or disposed on the subject property (including no migration of these substances from adjacent properties).” There appears to be sufficient information to categorize the subject property and it appears that no further effort needs to be made to obtain additional information. There are no findings of an adverse nature on the subject property itself or from adjacent properties. It is recommended that the proposed transfer of the subject property from the USAF to DOE proceed.« less