Micro-structural characterization of the hydration products of bauxite-calcination-method red mud-coal gangue based cementitious materials.

PubMed

Liu, Xiaoming; Zhang, Na; Yao, Yuan; Sun, Henghu; Feng, Huan

2013-11-15

In this research, the micro-structural characterization of the hydration products of red mud-coal gangue based cementitious materials has been investigated through SEM-EDS, (27)Al MAS NMR and (29)Si MAS NMR techniques, in which the used red mud was derived from the bauxite calcination method. The results show that the red mud-coal gangue based cementitious materials mainly form fibrous C-A-S-H gel, needle-shaped/rod-like AFt in the early hydration period. With increasing of the hydration period, densification of the pastes were promoted resulting in the development of strength. EDS analysis shows that with the Ca/Si of red mud-coal gangue based cementitious materials increases, the average Ca/Si and Ca/(Si+Al) atomic ratio of C-A-S-H gel increases, while the average Al/Si atomic ratio of C-A-S-H gel decreases. MAS NMR analysis reveals that Al in the hydration products of red mud-coal gangue based cementitious materials exists in the forms of Al(IV) and Al(VI), but mainly in the form of Al(VI). Increasing the Ca/Si ratio of raw material promotes the conversion of [AlO4] to [AlO6] and inhibits the combination between [AlO4] and [SiO4] to form C-A-S-H gel. Meanwhile, the polymerization degree of [SiO4] in the hydration products declines. Published by Elsevier B.V.

Lunar mineral feedstocks from rocks and soils: X-ray digital imaging in resource evaluation

NASA Technical Reports Server (NTRS)

Chambers, John G.; Patchen, Allan; Taylor, Lawrence A.; Higgins, Stefan J.; Mckay, David S.

1994-01-01

The rocks and soils of the Moon provide raw materials essential to the successful establishment of a lunar base. Efficient exploitation of these resources requires accurate characterization of mineral abundances, sizes/shapes, and association of 'ore' and 'gangue' phases, as well as the technology to generate high-yield/high-grade feedstocks. Only recently have x-ray mapping and digital imaging techniques been applied to lunar resource evaluation. The topics covered include inherent differences between lunar basalts and soils and quantitative comparison of rock-derived and soil-derived ilmenite concentrates. It is concluded that x-ray digital-imaging characterization of lunar raw materials provides a quantitative comparison that is unattainable by traditional petrographic techniques. These data are necessary for accurately determining mineral distributions of soil and crushed rock material. Application of these techniques will provide an important link to choosing the best raw material for mineral beneficiation.

Attenuation of heavy metals by geosynthetics in the coal gangue-filled columns.

PubMed

Wang, Ping; Hu, Zhenqi; Wang, Peijun

2013-01-01

In the subsided areas backfilled with coal gangue, an issue of continuing environmental concern is the migration of hazardous metals to the subsurface soil and groundwater. As an effective isolation material, geosynthetics have been scarcely applied into mining areas reclamation of China. This paper describes research aimed at characterizing the behaviours of different geosynthetics in the leaching columns filled with coal gangues. Four types of geosynthetics were selected: fibres needle-punched nonwoven geotextiles, high-density polyethylene, needle-punched Na-bentonite geosynthetic clay liner (GCL-NP) and Na-bentonite geosynthetic-overbited film. Heavy metals were significantly attenuated and by monitoring aqueous solutions in the whole percolation period, negative correlation was found between pH value and concentration of heavy metals. Generally, GCL-NP showed comparatively better effects on attenuating the migration of heavy metals. According to the meta-analysis of heavy metals present in the leachates and retained in the columns, geosynthetics have good capabilities of sorption and retardation, which can delay the breakthrough time of heavy metals and retard the accumulation in the subsurface. Future research will use X-ray diffraction and micro-imaging (electron microprobe and scanning electron microscopy) to further explain retention mechanisms.

Mineralized aplite—pegmatite at Jabal Sa'id, Hijaz region, Kingdom of Saudi Arabia

NASA Astrophysics Data System (ADS)

Hackett, Damien

The Jabal Sa'id aplite—pegmatite, located at 23°49'03″N, 40°56'30″E, is part of the Jabal Hadb ash Sharar granite complex and resulted from emplacement of a residual volatile-rich fraction of alkali granite magma dominantly above a chilled carapace. Mineralization is layered, with four peak grades in layers 20-25 m wide, one of which may represent a mineral resource with greater potential than the aplite—pegmatite as a whole. The grades of all elements, except Zr, increase towards the upper part of the body. Chemical composition is extremely variable. Major-oxide data confirm previously determined geochemical characteristics and genetic relationships that suggested this body is an apogranite. However, the abundant new data also show that differences between the aplite—pegmatite and cognate alkali microgranite are not as great as previously reported, except for Na 2O which is extremely depleted in the apogranite. REE data support suggested genetic relationships and indicate that feldspar fractionation was important during crystallization. They also show that the content of HREE is comparatively constant throughout the aplite—pegmatite, and that variations in total REE content are caused by variations in the content of LREE. Bastnaesite and synchysite-(Y) are the principal rare-earth-element minerals, and are accompanied by monazite and synchesite; pyrochlore and thorite are also important ore minerals. Other elements concentrated in the aplite—pegmatite, such as Ta, Sn and U, occur only in solid solution in these minerals. The grain size of the ore minerals is commonly in the range 0.02-0.2 mm, and the grain size of gangue minerals, quartz, microcline and lesser amounts of aegirine and arfvedsonite, is typically in the range 1.0-4.0 mm. The ore minerals occur typically along gangue mineral boundaries. Zoning within the body permits calculation of high- and low-grade reserves which correspond to the upper and lower part of the apogranite.

Study of the technology of heat pipe on prevention wildfire of coal gangue hill

NASA Astrophysics Data System (ADS)

Deng, Jun; Li, Bei; Ding, Ximei; Ma, Li

2017-04-01

Self-ignitable coal gangue hill (CGH) is one kind of special combustion system, which has the characteristics of low self-ignite point, large heat storage, and easy reignition. The currently industrial fire extinguishing methods, such as inhibiting tendency of coal self-ignition, loessial overburden, and cement grouting, had unsatisfied effects for dispersing the heat out in time. Correspondingly, the CGH will lead reignition more frequently with the passage of time. The high underground temperature of CGH threatens the process of ecological and vegetation construction. Therefore, the elimination of high temperature is a vital issue to be solved urgently for habitat restoration. To achieve the ultimately ecological management goal of self-ignitable CGH - extinguishing the fire completely and never reignited, it is crucial to break the heat accumulation. Heat-pipe (HP) has a character of high efficient heat transfer capacity for eliminating the continuously high temperature in CGH. An experimental system was designed to test the heat transfer performance of HP for preventing and extinguishing the spontaneous combustion of coal gangue. Based on the heat transfer theory, the resistance network of the coal-HP heat removal system was analyzed for studying the cooling effect of HP. The experimental results show that the HP can accelerate the heat release in coal gangue pile. The coal temperature could be controlled at 59.6 ˚ C with HP in 7 h and the highest cooling value is 39.4 % with HP in 150 h, which can effectively cool the temperatures of high temperature zones. As a powerful heat transfer components, as soon as HPs were inserted into the CGH with a reasonable distance, it can completely play a vital role in inhibiting the coal self-ignition process.

Chemical and colloidal aspects of collectorless flotation behavior of sulfide and non-sulfide minerals.

PubMed

Aghazadeh, Sajjad; Mousavinezhad, Seyed Kamal; Gharabaghi, Mahdi

2015-11-01

Flotation has been widely used for separation of valuable minerals from gangues based on their surface characterizations and differences in hydrophobicity on mineral surfaces. As hydrophobicity of minerals widely differs from each other, their separation by flotation will become easier. Collectors are chemical materials which are supposed to make selectively valuable minerals hydrophobic. In addition, there are some minerals which based on their surface and structural features are intrinsically hydrophobic. However, their hydrophobicities are not strong enough to be floatable in the flotation cell without collectors such as sulfide minerals, coal, stibnite, and so forth. To float these minerals in a flotation cell, their hydrophobicity should be increased in specific conditions. Various parameters including pH, Eh, size distribution, mill types, mineral types, ore characterization, and type of reaction in flotation cells affect the hydrophobicity of minerals. Surface analysis results show that when sulfide minerals experience specific flotation conditions, the reactions on the surface of these minerals increase the amount of sulfur on the surface. These phenomenons improve the hydrophobicity of these minerals due to strong hydrophobic feature of sulfurs. Collectorless flotation reduces chemical material consumption amount, increases flotation selectivity (grade increases), and affects the equipment quantities; however, it can also have negative effects. Some minerals with poor surface floatability can be increased by adding some ions to the flotation system. Depressing undesirable minerals in flotation is another application of collectorless flotation.

Microbial Variants from Iron Ore Slimes: Mineral Specificity and pH Tolerance.

PubMed

Abhilash; Ghosh, A; Pandey, B D; Sarkar, S

2015-12-01

This paper describes the isolation of the native bacterial strains from the iron ore mines slime pond and its extremophilic characteristics. The two microbial isolates designated as CNIOS-1 and CNIOS-2 were grown in selective silicate broth at pH 7.0 and the organisms were tested for their selective adhesion on silicate and alumina minerals. The silicate bacteria with their exopolymers are very potent to grow over aluminosilicates. It was established that CNIOS-1 grew preferentially in the presence of silicate mineral compared to CNIOS-2 which grew in the presence of alumina. The organisms were tested for growth at various pH and trials were carried to define their efficacy for eventual applications to remove gangue minerals of silica and alumina from the raw material.

The environmental geochemistry of trace elements and naturally radionuclides in a coal gangue brick-making plant.

PubMed

Zhou, Chuncai; Liu, Guijian; Cheng, Siwei; Fang, Ting; Lam, Paul K S

2014-08-28

An investigation focused on the transformation and distribution behaviors of trace elements and natural radionuclides around a coal gangue brick plant was conducted. Simultaneous sampling of coal gangue, brick, fly ash and flue gas were implemented. Soil, soybean and earthworm samples around the brick plant were also collected for comprehensive ecological assessment. During the firing process, trace elements were released and redistributed in the brick, fly ash and the flue gas. Elements can be divided into two groups according to their releasing characteristics, high volatile elements (release ratio higher than 30%) are represented by Cd, Cu, Hg, Pb, Se and Sn, which emitted mainly in flue gas that would travel and deposit at the northeast and southwest direction around the brick plant. Cadmium, Ni and Pb are bio-accumulated in the soybean grown on the study area, which indicates potential health impacts in case of human consumption. The high activity of natural radionuclides in the atmosphere around the plant as well as in the made-up bricks will increase the health risk of respiratory system.

The Environmental Geochemistry of Trace Elements and Naturally Radionuclides in a Coal Gangue Brick-Making Plant

PubMed Central

Zhou, Chuncai; Liu, Guijian; Cheng, Siwei; Fang, Ting; Lam, Paul K. S.

2014-01-01

An investigation focused on the transformation and distribution behaviors of trace elements and natural radionuclides around a coal gangue brick plant was conducted. Simultaneous sampling of coal gangue, brick, fly ash and flue gas were implemented. Soil, soybean and earthworm samples around the brick plant were also collected for comprehensive ecological assessment. During the firing process, trace elements were released and redistributed in the brick, fly ash and the flue gas. Elements can be divided into two groups according to their releasing characteristics, high volatile elements (release ratio higher than 30%) are represented by Cd, Cu, Hg, Pb, Se and Sn, which emitted mainly in flue gas that would travel and deposit at the northeast and southwest direction around the brick plant. Cadmium, Ni and Pb are bio-accumulated in the soybean grown on the study area, which indicates potential health impacts in case of human consumption. The high activity of natural radionuclides in the atmosphere around the plant as well as in the made-up bricks will increase the health risk of respiratory system. PMID:25164252

Potential ecological risk assessment and prediction of soil heavy-metal pollution around coal gangue dump

NASA Astrophysics Data System (ADS)

Jiang, X.; Lu, W. X.; Zhao, H. Q.; Yang, Q. C.; Yang, Z. P.

2014-06-01

The aim of the present study is to evaluate the potential ecological risk and trend of soil heavy-metal pollution around a coal gangue dump in Jilin Province (Northeast China). The concentrations of Cd, Pb, Cu, Cr and Zn were monitored by inductively coupled plasma mass spectrometry (ICP-MS). The potential ecological risk index method developed by Hakanson (1980) was employed to assess the potential risk of heavy-metal pollution. The potential ecological risk in the order of ER(Cd) > ER(Pb) > ER(Cu) > ER(Cr) > ER(Zn) have been obtained, which showed that Cd was the most important factor leading to risk. Based on the Cd pollution history, the cumulative acceleration and cumulative rate of Cd were estimated, then the fixed number of years exceeding the standard prediction model was established, which was used to predict the pollution trend of Cd under the accelerated accumulation mode and the uniform mode. Pearson correlation analysis and correspondence analysis are employed to identify the sources of heavy metals and the relationship between sampling points and variables. These findings provided some useful insights for making appropriate management strategies to prevent or decrease heavy-metal pollution around a coal gangue dump in the Yangcaogou coal mine and other similar areas elsewhere.

Potential ecological risk assessment and prediction of soil heavy metal pollution around coal gangue dump

NASA Astrophysics Data System (ADS)

Jiang, X.; Lu, W. X.; Yang, Q. C.; Yang, Z. P.

2014-03-01

Aim of the present study is to evaluate the potential ecological risk and predict the trend of soil heavy metal pollution around a~coal gangue dump in Jilin Province (Northeast China). The concentrations of Cd, Pb, Cu, Cr and Zn were monitored by inductively coupled plasma mass spectrometry (ICP-MS). The potential ecological risk index method developed by Hakanson (1980) was employed to assess the potential risk of heavy metal pollution. The potential ecological risk in an order of E(Cd) > E(Pb) > E(Cu) > E(Cr) > E(Zn) have been obtained, which showed that Cd was the most important factor led to risk. Based on the Cd pollution history, the cumulative acceleration and cumulative rate of Cd were estimated, and the fixed number of years exceeding standard prediction model was established, which was used to predict the pollution trend of Cd under the accelerated accumulation mode and the uniform mode. Pearson correlation analysis and correspondence analysis are employed to identify the sources of heavy metal, and the relationship between sampling points and variables. These findings provide some useful insights for making appropriate management strategies to prevent and decrease heavy metal pollution around coal gangue dump in Yangcaogou coal mine and other similar areas elsewhere.

Mineral sulphide-lime reactions and effect of CaO/C mole ratio during carbothermic reduction of complex mineral sulphides

NASA Astrophysics Data System (ADS)

Hara, Yotamu Stephen Rainford

2014-01-01

Mineral sulphide (MS)-lime (CaO) ion exchange reactions (MS + CaO = MO + CaS) and the effect of CaO/C mole ratio during carbothermic reduction (MS + CaO + C = M + CaS + CO(g)) were investigated for complex froth flotation mineral sulphide concentrates. Phases in the partially and fully reacted samples were characterised by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The primary phases during mineral sulphide-lime ion exchange reactions are Fe3O4, CaSO4 Cu2S, and CaS. A complex liquid phase of Ca2CuFeO3S forms during mineral sulphide-lime exchange reactions above 1173 K. The formation mechanisms of Ca2CuFeO3S liquid phase are determined by characterising the partially reacted samples. The reduction rate and extent of mineral sulphides in the presence of CaO and C increase with the increase in CaO/C ratio. The metallic phases are surrounded by the CaS rich phase at CaO/C > 1, but the metallic phases and CaS are found as separate phases at CaO/C < 1. Experimental results show that the stoichiometric ratio of carbon should be slightly higher than that of CaO. The reactions between CaO and gangue minerals (SiO2 and Al2O3) are only observed at CaO/C > 1 and the reacted samples are excessively sintered.

EPITHERMAL GOLD-SILVER MINERALIZATION RELATED TO VOLCANIC SUBSIDENCE IN THE CUSTER GRABEN, CUSTER COUNTY, IDAHO.

USGS Publications Warehouse

Johnson, Kathleen M.; McIntyre, David H.

1984-01-01

The Custer graben is a 13 by 32 km northeast-trending volcano-tectonic graben in the Challis volcanic field of central Idaho. Andesites, rhyolites, and associated pyroclastic rocks host vein and disseminated gold-silver deposits that are localized along discrete northeast- and northwest-trending fracture zones. Ore minerals in vein deposits are electrum, native gold and silver, chalcopyrite, and various sulfosalts in a gangue of pyrite and fine-grained quartz. At the Sunbeam Mine, near the center of the graben, vein and disseminated gold-silver mineralization occurred in hydrothermally altered rhyolite and pyroclastic rocks. The host rock has been pervasively silicified, and the feldspars altered to clay minerals. Analyses of surface and drill-core samples show that altered rocks are variably enriched in gold, silver, molybdenum, arsenic, zirconium, and selenium. Intense silicification is shown by SiO//2 values at high as 93%.

Integrated Utilization of Sewage Sludge and Coal Gangue for Cement Clinker Products: Promoting Tricalcium Silicate Formation and Trace Elements Immobilization

PubMed Central

Yang, Zhenzhou; Zhang, Yingyi; Liu, Lili; Seetharaman, Seshadri; Wang, Xidong; Zhang, Zuotai

2016-01-01

The present study firstly proposed a method of integrated utilization of sewage sludge (SS) and coal gangue (CG), two waste products, for cement clinker products with the aim of heat recovery and environment protection. The results demonstrated that the incremental amounts of SS and CG addition was favorable for the formation of tricalcium silicate (C3S) during the calcinations, but excess amount of SS addition could cause the impediment effect on C3S formation. Furthermore, it was also observed that the C3S polymorphs showed the transition from rhombohedral to monoclinic structure as SS addition was increased to 15 wt %. During the calcinations, most of trace elements could be immobilized especially Zn and cannot be easily leached out. Given the encouraging results in the present study, the co-process of sewage sludge and coal gangue in the cement kiln can be expected with a higher quality of cement products and minimum pollution to the environment. PMID:28773400

Geology and mineral deposits of the Minnie Moore and Bullion mineralized areas, Blaine County, Idaho

USGS Publications Warehouse

Link, Paul Karl; Worl, Ronald G.

2001-01-01

In the early 1880?s the discovery of rich ores in the Minnie Moore and Bullion mineralized areas sparked a rush to settle and develop the Wood River valley. Silver and lead discoveries in these areas spurred the boom in mining after completion of the Oregon Short Line Railroad to Hailey in 1883. In both areas the ore comprises galena, sphalerite, and tetrahedrite in a gangue of siderite, calcite, or quartz. Minor goldbearing quartz veins are also present. The ore is in fissure and replacement veins along fracture systems that formed in Late Cretaceous time, after intrusion of nearby granodiorite or quartz diorite stocks. The ore formed under mesothermal conditions and heat was supplied by the nearby plutons. In the Minnie Moore area, the mineralized veins are cut by low-angle normal faults that are of probable Eocene age. In the Minnie Moore mineralized area, the host rock is the middle part of the Devonian Milligen Formation, (the informal Lucky Coin limestone and Triumph argillite), which is the same stratigraphic level as the host ore in the rich Triumph mine northeast of Hailey. In the Bullion mineralized area, the ore is hosted by the lower member of the Middle Pennsylvanian to Lower Permian Dollarhide Formation. Rich ore was mined in several tunnels that reached the Mayflower vein, a northwest-striking mineralized shear zone. The deposits are thought to be mainly mesothermal veins that formed in association with Cretaceous magmatism. The syngenetic stratiform model of ore formation has often been applied to these deposits, however, no evidence of syngenetic mineralization was found in this study. Faulting has displaced most of the major orebodies and thus has made mining these deposits a challenge.

Geology and mineral deposits of the St. Regis-Superior area, Mineral County, Montana

USGS Publications Warehouse

Campbell, Arthur B.

1960-01-01

The St. Regis-Superior area occupies about 300 square miles in northwestern Montana and includes parts of the Squaw Peak Range and Coeur d'Alerie Mountains of the northern Rocky Mountains physiographic province. Nearly 50,000 feet of metasedimentary rocks of the Precambrian Belt series, chiefly varieties of quartzite and argillite, underlies most of the area. The Belt series is informally subdivided with reference to the top of the Wallace formation into lower and upper parts. In this area, the lower part of the Belt series is divided into the Prichard, Burke and Revett, St. Regis, and Wallace formations, in order of decreasing age, and the upper part of the Belt series or the Missoula group is divided »into the Spruce, Lupine, Sloway, and Bouchard formations, and an unnamed feldspathic quartzite at Rock Rabbit Ridge, also from oldest to youngest. Formations in the lower part of the Belt series are correlated with formations of the same names in the Coeur d'Alene district, and formations in the upper part of the Belt series are tentatively correlated in part with formations of the Missoula group in the vicinity of Missoula, Mont. Paleozoic quartzite, shale, limestone, and dolomite crop out in several localities in the southeastern part of the area. The limestone unit contains fragments of a single species of Glossopleura of early Middle Cambrian age which, together with lithologic similarities, has been used to correlate at least the quartzite, shale, and limestone part of this Paleozoic sequence with the Flathead sandstone, Gordon shale, and Damnation limestone sequence known elsewhere in northwestern Montana. Several small diabasic dikes and sills are present in the area, generally associated with northwestward-trending faults. The major faults generally trend northwestward and are considered to be part of the Lewis and Clark structural line. The Osburn fault, the major element of the Lewis and Clark line through the Coeur d'Alene district and western Mineral

75 FR 69617 - Lowering Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust Monitors

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-15

... 1219-AB64 Lowering Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust... hearings on the proposed rule addressing Lowering Miners' Exposure to Respirable Coal Mine Dust, Including... miners' exposure to respirable coal mine dust by revising the Agency's existing standards on miners...

76 FR 2617 - Lowering Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust Monitors

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-14

... 1219-AB64 Lowering Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust... comment period on the proposed rule addressing Lowering Miners' Exposure to Respirable Coal Mine Dust...), MSHA published a proposed rule, Lowering Miners' Exposure to Respirable Coal Mine Dust, Including...

Surface chemistry and flotation behavior of monazite, apatite, ilmenite, quartz, rutile, and zircon using octanohydroxamic acid collector

NASA Astrophysics Data System (ADS)

Nduwa Mushidi, Josue

Global increase in rare earth demand and consumption has led to further understanding their beneficiation and recovery. Monazite is the second most important rare earth mineral that can be further exploited. In this study, the surface chemistry of monazite in terms of zeta potential, adsorption density, and flotation response by microflotation using octanohydroxamic acid is determined. Apatite, ilmenite, quartz, rutile, and zircon are minerals that frequently occur with monazite among other minerals. Hence they were chosen as gangue minerals in this study. The Iso Electric Point (IEP) of monazite, apatite, ilmenite, quartz, rutile, and zircon are 5.3, 8.7, 3.8, 3.4, 6.3, and 5.1 respectively. The thermodynamic parameters of adsorption were also evaluated. Ilmenite, rutile and zircon have high driving forces for adsorption with DeltaGads. = 20.48, 22.10, and 22.4 kJ/mol respectively. The free energy of adsorption is 14.87 kJ/mol for monazite. Adsorption density testing shows that octanohydroxamic acid adsorbs on negatively charged surfaces of monazite and its gangue minerals which indicates chemisorption. This observation was further confirmed by microflotation experiments. Increasing the temperature to 80°C raises the adsorption and flotability of monazite and gangue minerals. This does not allow for effective separation. Sodium silicate appeared to be most effective to depress associated gangue minerals. Finally, the fundamentals learned were applied to the flotation of monazite ore from Mt. Weld. However, these results showed no selectivity due to the presence of goethite as fine particles and due to a low degree of liberation of monazite in the ore sample.

Permeability of Granite Including Macro-Fracture Naturally Filled with Fine-Grained Minerals

NASA Astrophysics Data System (ADS)

Nara, Yoshitaka; Kato, Masaji; Niri, Ryuhei; Kohno, Masanori; Sato, Toshinori; Fukuda, Daisuke; Sato, Tsutomu; Takahashi, Manabu

2018-03-01

Information on the permeability of rock is essential for various geoengineering projects, such as geological disposal of radioactive wastes, hydrocarbon extraction, and natural hazard risk mitigation. It is especially important to investigate how fractures and pores influence the physical and transport properties of rock. Infiltration of groundwater through the damage zone fills fractures in granite with fine-grained minerals. However, the permeability of rock possessing a fracture naturally filled with fine-grained mineral grains has yet to be investigated. In this study, the permeabilities of granite samples, including a macro-fracture filled with clay and a mineral vein, are investigated. The permeability of granite with a fine-grained mineral vein agrees well with that of the intact sample, whereas the permeability of granite possessing a macro-fracture filled with clay is lower than that of the macro-fractured sample. The decrease in the permeability is due to the filling of fine-grained minerals and clay in the macro-fracture. It is concluded that the permeability of granite increases due to the existence of the fractures, but decreases upon filling them with fine-grained minerals.

Mass change calculations of hydrothermal alterations within the volcanogenic metasediments hosted Cu-Pb (-Zn) mineralization at Halilar area, NW Turkey

NASA Astrophysics Data System (ADS)

Kiran Yildirim, Demet; Abdelnasser, Amr; Doner, Zeynep; Kumral, Mustafa

2016-04-01

The Halilar Cu-Pb (-Zn) mineralization that is formed in the volcanogenic metasediments of Bagcagiz Formation at Balikesir province, NW Turkey, represents locally vein-type deposit as well as restricted to fault gouge zone directed NE-SW along with the lower boundary of Bagcagiz Formation and Duztarla granitic intrusion in the study area. Furthermore, This granite is traversed by numerous mineralized sheeted vein systems, which locally transgress into the surrounding metasediments. Therefore, this mineralization closely associated with intense hydrothermal alteration within brecciation, and quartz stockwork veining. The ore mineral assemblage includes chalcopyrite, galena, and some sphalerite with covellite and goethite formed during three phases of mineralization (pre-ore, main ore, and supergene) within an abundant gangue of quartz and calcite. The geologic and field relationships, petrographic and mineralogical studies reveal two alteration zones occurred with the Cu-Pb (-Zn) mineralization along the contact between the Bagcagiz Formation and Duztarla granite; pervasive phyllic alteration (quartz, sericite, and pyrite), and selective propylitic alteration (albite, calcite, epidote, sericite and/or chlorite). This work, by using the mass balance calculations, reports the mass/volume changes (gain and loss) of the chemical components of the hydrothermal alteration zones associated with Halilar Cu-Pb (-Zn) mineralization at Balikesir area (Turkey). It revealed that the phyllic alteration has enrichments of Si, Fe, K, Ba, and LOI with depletion of Mg, Ca, and Na reflect sericitization of alkali feldspar and destruction of ferromagnesian minerals. This zone has high Cu and Pb with Zn contents represents the main mineralized zone. On the other hand, the propylitic zone is characterized by addition of Ca, Na, K, Ti, P, and Ba with LOI and Cu (lower content) referring to the replacement of plagioclase and ferromagnesian minerals by albite, calcite, epidote, and sericite

Modification of waste coal gangue and its application in the removal of Mn(2+) from aqueous solution.

PubMed

Qiu, Ruifang; Cheng, Fangqin

We developed a new calcination method to convert coal gangue (CG), a common waste generated from coal production process, into a modified form, which could be used as an adsorbent to remove Mn(2+) from aqueous solution. Sodium tetraborate (Na2B4O7·10H2O) was added into the CG calcination process as an additive, and the concentrations of Na2B4O7·10H2O were optimized along with the calcination temperature to obtain the best adsorbent capacity of modified coal gangue (MCG). We applied multiple analytical methods such as scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy and Brunauer-Emmett-Teller analysis to characterize the MCG. The results showed it had a smaller particle size and a larger specific surface area and pore volume after modification. It also indicated that the phase of CG transformed from kaolinite to metakaolinite after calcination. Moreover, a new substance was generated with two new peaks at 1,632 cm(-1) and 799 cm(-1). The Mn(2+) absorption capacity of MCG was evaluated using a series of experiments with different adsorbent doses, pH values and initial Mn(2+) concentrations during the adsorption process. We found that Mn(2+) adsorbent capacity of MCG increased by more than seven-fold compared to that of CG. The Langmuir isotherm model and the pseudo-second-order kinetic model provided the best fit to the adsorption processes.

76 FR 25277 - Lowering Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust Monitors

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-04

... 1219-AB64 Lowering Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust... to Respirable Coal Mine Dust, Including Continuous Personal Dust Monitors. This extension gives... Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust Monitors. In response...

Ore genesis constraints on the Idaho Cobalt Belt from fluid inclusion gas, noble gas isotope, and ion ratio analyses

USGS Publications Warehouse

Hofstra, Albert H.; Landis, Gary P.

2012-01-01

The Idaho cobalt belt is a 60-km-long alignment of deposits composed of cobaltite, Co pyrite, chalcopyrite, and gold with anomalous Nb, Y, Be, and rare-earth elements (REEs) in a quartz-biotite-tourmaline gangue hosted in Mesoproterozoic metasedimentary rocks of the Lemhi Group. It is the largest cobalt resource in the United States with historic production from the Blackbird Mine. All of the deposits were deformed and metamorphosed to upper greenschist-lower amphibolite grade in the Cretaceous. They occur near a 1377 Ma anorogenic bimodal plutonic complex. The enhanced solubility of Fe, Co, Cu, and Au as chloride complexes together with gangue biotite rich in Fe and Cl and gangue quartz containing hypersaline inclusions allows that hot saline fluids were involved. The isotopes of B in gangue tourmaline are suggestive of a marine source, whereas those of Pb in ore suggest a U ± Th-enriched source. The ore and gangue minerals in this belt may have trapped components in fluid inclusions that are distinct from those in post-ore minerals and metamorphic minerals. Such components can potentially be identified and distinguished by their relative abundances in contrasting samples. Therefore, we obtained samples of Co and Cu sulfides, gangue quartz, biotite, and tourmaline and post-ore quartz veins as well as Cretaceous metamorphic garnet and determined the gas, noble gas isotope, and ion ratios of fluid inclusion extracts by mass spectrometry and ion chromatography. The most abundant gases present in extracts from each sample type are biased toward the gas-rich population of inclusions trapped during maximum burial and metamorphism. All have CO2/CH4 and N2/Ar ratios of evolved crustal fluids, and many yield a range of H2-CH4-CO2-H2S equilibration temperatures consistent with the metamorphic grade. Cretaceous garnet and post-ore minerals have high RH and RS values suggestive of reduced sulfidic conditions. Most extracts have anomalous 4He produced by decay of U and Th and

Orogenic-type copper-gold-arsenic-(bismuth) mineralization at Flatschach (Eastern Alps), Austria

NASA Astrophysics Data System (ADS)

Raith, Johann G.; Leitner, Thomas; Paar, Werner H.

2015-10-01

Structurally controlled Cu-Au mineralization in the historic Flatschach mining district (Styria, Austria) occurs in a NE-SW to NNE-WSW oriented vein system as multiple steep-dipping calcite-(dolomite)-quartz veins in amphibolite facies metamorphic rocks (banded gneisses/amphibolites, orthogneisses, metagranitoids) of the poly-metamorphosed Austroalpine Silvretta-Seckau nappe. Vein formation postdated ductile deformation events and Eoalpine (Late Cretaceous) peak metamorphism but predated Early to Middle Miocene sediment deposition in the Fohnsdorf pull-apart basin; coal-bearing sediments cover the metamorphic basement plus the mineralized veins at the northern edge of the basin. Three gold-bearing ore stages consist of a stage 1 primary hydrothermal (mesothermal?) ore assemblage dominated by chalcopyrite, pyrite and arsenopyrite. Associated minor minerals include alloclasite, enargite, bornite, sphalerite, galena, bismuth and matildite. Gold in this stage is spatially associated with chalcopyrite occurring as inclusions, along re-healed micro-fractures or along grain boundaries of chalcopyrite with pyrite or arsenopyrite. Sericite-carbonate alteration is developed around the veins. Stage 2 ore minerals formed by the replacement of stage 1 sulfides and include digenite, anilite, "blue-remaining covellite" (spionkopite, yarrowite), bismuth, and the rare copper arsenides domeykite and koutekite. Gold in stage 2 is angular to rounded in shape and occurs primarily in the carbonate (calcite, Fe-dolomite) gangue and less commonly together with digenite, domeykite/koutekite and bismuth. Stage 3 is a strongly oxidized assemblage that includes hematite, cuprite, and various secondary Cu- and Fe-hydroxides and -carbonates. It formed during supergene weathering. Stage 1 and 2 gold consists mostly of electrum (gold fineness 640-860; mean = 725; n = 46), and rare near pure gold (fineness 930-940; n = 6). Gold in stage 3 is Ag-rich electrum (fineness 350-490, n = 12), and has a

A review of zinc oxide mineral beneficiation using flotation method.

PubMed

Ejtemaei, Majid; Gharabaghi, Mahdi; Irannajad, Mehdi

2014-04-01

In recent years, extraction of zinc from low-grade mining tailings of oxidized zinc has been a matter of discussion. This is a material which can be processed by flotation and acid-leaching methods. Owing to the similarities in the physicochemical and surface chemistry of the constituent minerals, separation of zinc oxide minerals from their gangues by flotation is an extremely complex process. It appears that selective leaching is a promising method for the beneficiation of this type of ore. However, with the high consumption of leaching acid, the treatment of low-grade oxidized zinc ores by hydrometallurgical methods is expensive and complex. Hence, it is best to pre-concentrate low-grade oxidized zinc by flotation and then to employ hydrometallurgical methods. This paper presents a critical review on the zinc oxide mineral flotation technique. In this paper, the various flotation methods of zinc oxide minerals which have been proposed in the literature have been detailed with the aim of identifying the important factors involved in the flotation process. The various aspects of recovery of zinc from these minerals are also dealt with here. The literature indicates that the collector type, sulfidizing agent, pH regulator, depressants and dispersants types, temperature, solid pulp concentration, and desliming are important parameters in the process. The range and optimum values of these parameters, as also the adsorption mechanism, together with the resultant flotation of the zinc oxide minerals reported in the literature are summarized and highlighted in the paper. This review presents a comprehensive scientific guide to the effectiveness of flotation strategy. Copyright © 2013 Elsevier B.V. All rights reserved.

New influence factor inducing difficulty in selective flotation separation of Cu-Zn mixed sulfide minerals

NASA Astrophysics Data System (ADS)

Deng, Jiu-shuai; Mao, Ying-bo; Wen, Shu-ming; Liu, Jian; Xian, Yong-jun; Feng, Qi-cheng

2015-02-01

Selective flotation separation of Cu-Zn mixed sulfides has been proven to be difficult. Thus far, researchers have found no satisfactory way to separate Cu-Zn mixed sulfides by selective flotation, mainly because of the complex surface and interface interaction mechanisms in the flotation solution. Undesired activation occurs between copper ions and the sphalerite surfaces. In addition to recycled water and mineral dissolution, ancient fluids in the minerals are observed to be a new source of metal ions. In this study, significant amounts of ancient fluids were found to exist in Cu-Zn sulfide and gangue minerals, mostly as gas-liquid fluid inclusions. The concentration of copper ions released from the ancient fluids reached 1.02 × 10-6 mol/L, whereas, in the cases of sphalerite and quartz, this concentration was 0.62 × 10-6 mol/L and 0.44 × 10-6 mol/L, respectively. As a result, the ancient fluid is a significant source of copper ions compared to mineral dissolution under the same experimental conditions, which promotes the unwanted activation of sphalerite. Therefore, the ancient fluid is considered to be a new factor that affects the selective flotation separation of Cu-Zn mixed sulfide ores.

Micron to Mine: Synchrotron Science for Mineral Exploration, Production, and Remediation

NASA Astrophysics Data System (ADS)

Banerjee, N.; Van Loon, L.; Flynn, T.

2017-12-01

Synchrotron science for mineral exploration, production, and remediation studies is a powerful tool that provides industry with relevant micron to macro geochemical information. Synchrotron micro X-ray fluorescence (SR-µXRF) offers a direct, high-resolution, rapid, and cost-effective chemical analysis while preserving the context of the sample by mapping ore minerals with ppm detection limits. Speciation of trace and deleterious elements can then be probed using X-ray absorption near-edge structure (XANES) spectroscopy. Large-scale (tens of cm) µXRF mapping and XANES analysis of samples collected at various mine locations have been undertaken to address questions regarding mineralization history to develop novel trace element exploration vectors. This information provides integral insights into trace element associations with ore minerals, local redox conditions responsible for mineralization, and mineralizing mechanisms. Gold is commonly intimately associated with sulfide mineralization (e.g., pyrite, arsenopyrite, etc.) and is present both as inclusions and filling fractures in sulfide grains. Gold may also occur as nanoparticles and/or in the sulfide mineral crystal lattice, known as "invisible gold". Understanding the nature and distribution of invisible gold in ore is integral to processing efficiency. The high flux and energy of a synchrotron light source allows for the detection of invisible gold by µXRF, and can probe its nature (metallic Au0 vs. lattice bound Au1+) using XANES spectroscopy. The long-term containment and management of arsenic is necessary to protect the health of both humans and the environment. Understanding the relationship of arsenic mineralization to gold deposits can lead to more sophisticated planning for mineral processing and the eventual storage of gangue materials. µXANES spectroscopy is an excellent tool for determining arsenic speciation within the context of the sample. Mineral phases such as arsenopyrite, scorodite, and

The Occupational Neuroses (including Miners' Nystagmus)

PubMed Central

Culpin, Millais

1933-01-01

These disorders seem to conform to the conception of “functional nervous disorder” in the narrow sense of the phrase. Specific difficulties in writers' cramp, however, often found to have symbolic significance to the patient. Cramp frequently one symptom in a larger syndrome. Both writers' and telegraphists' cramp are excrescences upon an underlying psychoneurosis, though associated symptoms are often overlooked. Miners' nystagmus supposed to be a physiological disorder that produces “neurasthenia”; ocular symptoms mostly psychoneurotic; the oscillation not a disability of itself. Night-blindness as a hysterical symptom. History of night-blindness in armies; its epidemic prevalence in Continental armies in the Great War and its comparative rarity in ours. Its absence in war pensioners and possible replacement by fear of the dark. Night-blindness in nystagmus probably a conversion of this fear. Accounts of nystagmus in crane-workers and train dispatchers. Cases of miners' nystagmus shown to be identical with psychoneuroses arising apart from nystagmus. The nervous symptoms increase as the nystagmus diminishes. Possibly the ocular disability behaves as a hysteria in guarding against further symptoms. Appearance of an occupational disorder among deep-sea divers, and the psychological investigation of individual cases described. Spurious unconsciousness was due to a condition of Angst which could be experimentally reproduced. The existence of a psychoneurotic basis and the possibility of foretelling the development of the specific disorder were demonstrated, Conclusion.—The occupational neuroses are to be regarded as minor psychoses (or psychoneuroses) and handled in accordance with modern principles of psychopathology. PMID:19989240

A review of the surface features and properties, surfactant adsorption and floatability of four key minerals of diasporic bauxite resources.

PubMed

Zhang, Ningning; Nguyen, Anh V; Zhou, Changchun

2018-04-01

Diasporic bauxite represents one of the major aluminum resources. Its upgrading for further processing involves a separation of diaspore (the valuable mineral) from aluminosilicates (the gangue minerals) such as kaolinite, illite, and pyrophyllite. Flotation is one of the most effective ways to realize the upgrading. Since flotation is a physicochemical process based on the difference in the surface hydrophobicity of different components, determining the adsorption characteristics of various flotation surfactants on the mineral surfaces is critical. The surfactant adsorption properties of the minerals, in turn, are controlled by the surface chemistry of the minerals, while the latter is related to the mineral crystal structures. In this paper, we first discuss the crystal structures of the four key minerals of diaspore, kaolinite, illite, and pyrophyllite as well as the broken bonds on their exposed surfaces after grinding. Next, we summarize the surface chemistry properties such as surface wettability and surface electrical properties of the four minerals, and the differences in these properties are explained from the perspective of mineral crystal structures. Then we review the adsorption mechanism and adsorption characteristics of surfactants such as collectors (cationic, anionic, and mixed surfactants), depressants (inorganic and organic), dispersants, and flocculants on these mineral surfaces. The separation of diaspore and aluminosilicates by direct flotation and reverse flotation are reviewed, and the collecting properties of different types of collectors are compared. Furthermore, the abnormal behavior of the cationic flotation of kaolinite is also explained in this section. This review provides a strong theoretical support for the optimization of the upgrading of diaspore bauxite ore by flotation and the early industrialization of the reverse flotation process. Copyright © 2018 Elsevier B.V. All rights reserved.

Mineral exploration, Mahd adh Dhahab District, Kingdom of Saudi Arabia

USGS Publications Warehouse

Worl, Ronald G.

1978-01-01

Mahd adh Dhahab is the largest of numerous ancient gold mines scattered through the Precambrian shield of Saudi Arabia and the only one with recent production. During the period 1939-54, 765,768 fine ounces of gold and 1,002,029 ounces of silver were produced from the mines by the Saudi Arabian Mining Syndicate. Ore minerals at Mahd adh Dhahab include free gold and silver, tellurides, sphalerite, and chalcopyrite in and associated with a system of north-trending quartz veins and quartz veinlet stockworks. Pyrite is a common sulfide gangue mineral. Country rocks are a north dipping sequence of pyroclastic and transported pyroclastic rocks of the Hulayfah Group that are locally highly silicified and potassium-feldspathized. The prime target for this exploration program was a north-trending zone of quartz veins and breccias, faults, alteration, and metalization approximately 400 m wide and 1000 m long. The ancient and recent mine workings are located in the northern part of this zone. Although the quartz veins and alteration cut all lithologies, the major metalization is confined to the intersection of veins and agglomerate. Ten holes were diamond drilled to explore geochemical, geological, and geophysical targets in the area. A significant new zone of metalization was discovered 700 m south of the ancient and recent mine workings and within the same major zone of quartz veins, alteration, and faults. Metalization in this southern mineralized zone is at the intersection of the quartz veins and a distinctive and highly altered agglomerate. The total zone of vein and agglomerate intercept is potentially metalized and comprises a block of ground 40 m thick and 400 m wide along the strike of the agglomerate and projected downdip 250 m. Tonnage of this block is 17.2 million tons. The explored zone, approximately 25 percent of the potentially metalized rock, has a potential resource of 1.1 million tons containing 27 g/t gold and 73 g/t silver.

Mineralogy and fluid inclusions study of carbonate-hosted Mississippi valley-type Ain Allega Pb-Zn-Sr-Ba ore deposit, Northern Tunisia

NASA Astrophysics Data System (ADS)

Abidi, R.; Slim-Shimi, N.; Somarin, A.; Henchiri, M.

2010-05-01

The Ain Allega Pb-Zn-Sr-Ba ore deposit is located in the flysch zone on the Eastern edge of the Triassic diapir of Jebel Hamra. It is part of the extrusive Triassic evaporate formation along the Ghardimaou-Cape Serrat faults. The ore body consists of argilic-dolomite breccias surrounded by argilo-gypsum Triassic formation, which forms the hanging wall of the deposit, and rimmed by the Paleocene marls. The ore minerals show a cap-rock type mineralization with different styles particularly impregnation in dolomite, cement of breccias, replacement ore and open space filling in the dissolution cavities and fractures. Ore minerals include sphalerite, galena, marcasite and pyrite. Principal gangue minerals are composed of barite, celestite, calcite, dolomite and quartz. The ore minerals are hosted by the Triassic carbonate rocks which show hydrothermal alteration, dissolution and brecciation. X-ray - crystallographic study of barite-celestite mineral series shows that pure barite and celestite are the abundant species, whereas strontianiferous barite (85-96.5% BaSO 4) and barian-celestite (95% SrSO 4) are minor. Primary and secondary mono-phase (liquid only) fluid inclusions are common in celestite. Microthermometric analyses in two-phases (liquid and vapour) fluid inclusions suggest that gangue and ore minerals were precipitated by a low-temperature (180 °C) saline (16.37 wt.% NaCl equivalent) solution originated possibly from a basinal brine with some input from magmatic or metamorphic fluid. Based on geology, mineralogy, texture and fluid characteristics, the Ain Allega deposit is classified as a carbonate-hosted Mississippi valley-type deposit.

Study of talcum charging status in parallel plate electrostatic separator based on particle trajectory analysis

NASA Astrophysics Data System (ADS)

Yunxiao, CAO; Zhiqiang, WANG; Jinjun, WANG; Guofeng, LI

2018-05-01

Electrostatic separation has been extensively used in mineral processing, and has the potential to separate gangue minerals from raw talcum ore. As for electrostatic separation, the particle charging status is one of important influence factors. To describe the talcum particle charging status in a parallel plate electrostatic separator accurately, this paper proposes a modern images processing method. Based on the actual trajectories obtained from sequence images of particle movement and the analysis of physical forces applied on a charged particle, a numerical model is built, which could calculate the charge-to-mass ratios represented as the charging status of particle and simulate the particle trajectories. The simulated trajectories agree well with the experimental results obtained by images processing. In addition, chemical composition analysis is employed to reveal the relationship between ferrum gangue mineral content and charge-to-mass ratios. Research results show that the proposed method is effective for describing the particle charging status in electrostatic separation.

Environmental investigation on co-combustion of sewage sludge and coal gangue: SO2, NOx and trace elements emissions.

PubMed

Yang, Zhenzhou; Zhang, Yingyi; Liu, Lili; Wang, Xidong; Zhang, Zuotai

2016-04-01

To promote the utilization of waste material as alternative fuel, the mono- and co-combustion characteristics of sewage sludge (SS) and coal gangue (CG) were systematically investigated, with emphasis on environmental influences. The emission of SO2, NOx as well as the trace elements during combustion of SS and CG were studied with regard to the effects of their chemistries, structures and interactions. Results showed that co-combustion can be beneficial for ignition performance. A synergic effect on both desulfurization and denitrification can be expected at ca. 800°C. Further, an enhanced retention of trace elements during co-combustion was also observed, especially for Pb and Zn. On the basis of the results, it can be expected that, with proper operation, co-combustion of SS and CG can be a promising method for the disposal of these two wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Feasibility Studies for Production of Pellet Grade Concentrate from Sub Grade Iron Ore Using Multi Gravity Separator

NASA Astrophysics Data System (ADS)

Rao, Gottumukkala Venkateswara; Markandeya, R.; Kumar, Rajan

2018-04-01

An attempt has been made to utilise Sub Grade Iron Ore by producing pellet grade concentrate from Deposit 5, Bacheli Complex, Bailadila, Chhattisgarh, India. The `as received' Run of Mine (ROM) sample assayed 40.80% Fe, 40.90% SiO2. Mineralogical studies indicated that the main ore mineral is Hematite and lone gangue mineral is Quartz. Mineral liberation studies indicated that, the ore mineral Hematite and gangue mineral Quartz are getting liberated below 100 microns. The stage crushed and ground sample was subjected to concentration by using a Multi Gravity Separator (MGS). Rougher Multi Gravity Separation (MGS) experimental results were optimised to recover highest possible iron values. A concentrate of 55.80% Fe with a yield of 61.73% by weight with a recovery of 84.42% Iron values was obtained in rougher MGS concentrate. Further experiments were carried out with rougher MGS concentrate to produce a concentrate suitable for commercial grade pellet concentrate. It was proved that a concentrate assaying 66.67% Fe, 3.12% SiO2 with an yield of 45.08% by weight and with a recovery of 73.67% iron values in the concentrate.

PRIMARY MINERALIZATION OF URANIUM-BEARING "SILICEOUS REEF" VEINS IN THE BOULDER BATHOLITH, MONTANA. PART I. THE HOST ROCKS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, H.D.; Bieler, B.H.

1960-01-01

Between 1952 and 1956 a study was made of some of the uranium-bearing hydrothermal veins in the northern part of the Boulder batholith, Montana. Three mines, the W. Wilson, G. Washington, and Free Enterprise, were investigated in detail. The veins are characterized by a microcrystalline quartz gangue containing sparsely scattered, very fine-grained sulfide minerals and uraninite. Above the present water table, secondary uranium minerals are abundant locally. Throughout the area the veins --called "siliceous reefs"--strike east to northeast, are of steep dip, and vary in thickness from a fraction of an inch to several feet. The country rock is granodioritemore » containing, in order of abundance, plagioclase (An/sub 30/ to An/sub 36/), quartz, orthoclase, biotite, and hornblende, with apatite, zircon, and sphene. Small bodies of aplite, pegmatite, and alaskite occur along some veins. The granodiorite adjacent to the veins is rather strongly altered. The alteration is similar throughout all of the deposits studied, in barren and orebearing portions alike. The essential minerals show a characteristic sequence of alteration, in the order hornblende, andesine, biotite, orthoclase, and quartz. Successive zones of alteration are characterized, from the vein outward, by maximum development of sericite (muscovite polytype 1M, in part), kaolinite, and montmorillonite. Other alteration products are quartz, pyrite, calcite, leucoxene, and chlorite. The alteration resulted in an increase in silica and ferric iron, a decrease in alumina, total iron, ferrous iron, lime, soda, and magnesia, and little change in potash, titania, phosphorus, carbon dioxide, and sulfur. Consideration of the stability fields of the sheet structure silicate minerals indicates little basis for interpretation of the temperatures prevailing during mineralization. (auth)« less

Minerals

MedlinePlus

Minerals are important for your body to stay healthy. Your body uses minerals for many different jobs, including keeping your bones, muscles, heart, and brain working properly. Minerals are also important for making enzymes and hormones. ...

Environment-oriented low-cost porous mullite ceramic membrane supports fabricated from coal gangue and bauxite.

PubMed

Lü, Qikai; Dong, Xinfa; Zhu, Zhiwen; Dong, Yingchao

2014-05-30

Porous mullite ceramic supports for filtration membrane were successfully fabricated via recycling of coal gangue and bauxite at sintering temperatures from 1100 to 1500°C with corn starch as pore-forming agent. The dynamic sintering behaviors, phase evolution, shrinkage, porosity and pore size, gas permeation flux, microstructure and mechanical property were systematically studied. A unique volume-expansion stage was observed at increased temperatures from 1276 to 1481°C caused by a mullitization-crystal-growth process. During this stage, open porosity increases and pore size distributions broaden, which result in a maximum of nitrogen gas flux at 1400°C. The X-ray diffraction results reveal that secondary mullitization took place from 1100°C and the major phase is mullite with a content of ∼84.7wt.% at 1400°C. SEM images show that the as-fabricated mullite supports have a porous microstructure composed of sintered glassy particles embedded with inter-locked mullite crystals, which grew gradually with increasing temperature from rod-like into blocky-like morphologies. To obtain mullite membrane supports with sufficient porosity and acceptable mechanical strength, the relationship between porosity and mechanical strength was investigated, which was fitted using a parabolic equation. Copyright © 2014 Elsevier B.V. All rights reserved.

Geologic map of southwestern Sequoia National Park and vicinity, Tulare County, California, including the Mineral King metamorphic pendant

NASA Astrophysics Data System (ADS)

Sisson, T. W.; Moore, J. G.

2012-12-01

From the late 1940s to the early 1990s, scientists of the U.S. Geological Survey (USGS) mapped the geology of most of Sequoia and Kings Canyon National Parks, California, and published the results as a series of 15-minute (1:62,500 scale) Geologic Quadrangles. The southwest corner of Sequoia National Park, encompassing the Mineral King and eastern edge of the Kaweah 15-minute topographic quadrangles, however, remained unfinished. At the request of the National Park Service's Geologic Resources Division (NPS-GRD), the USGS has mapped the geology of that area using 7.5-minute (1:24,000 scale) topographic bases and high-resolution ortho-imagery. With partial support from NPS-GRD, the major plutons in the map area were dated by the U-Pb zircon method with the Stanford-USGS SHRIMP-RG ion microprobe. Highlights include: (1) Identification of the Early Cretaceous volcano-plutonic suite of Mineral King (informally named), consisting of three deformed granodiorite plutons and the major metarhyolite tuffs of the Mineral King metamorphic pendant. Members of the suite erupted or intruded at 130-140 Ma (pluton ages: this study; rhyolite ages: lower-intercept concordia from zircon results of Busby-Spera, 1983, Princeton Ph.D. thesis, and from Klemetti et al., 2011, AGU abstract) during the pause of igneous activity between emplacement of the Jurassic and Cretaceous Sierran batholiths. (2) Some of the deformation of the Mineral King metamorphic pendant is demonstrably Cretaceous, with evidence including map-scale folding of Early Cretaceous metarhyolite tuff, and an isoclinally folded aplite dike dated at 98 Ma, concurrent with the large 98-Ma granodiorite of Castle Creek that intruded the Mineral King pendant on the west. (3) A 21-km-long magmatic synform within the 99-100 Ma granite of Coyote Pass that is defined both by inward-dipping mafic inclusions (enclaves) and by sporadic, cm-thick, sharply defined mineral layering. The west margin of the granite of Coyote Pass overlies

Minerals Yearbook, volume I, Metals and Minerals

USGS Publications Warehouse

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Optical properties of mineral dust aerosol including analysis of particle size, composition, and shape effects, and the impact of physical and chemical processing

NASA Astrophysics Data System (ADS)

Alexander, Jennifer Mary

Atmospheric mineral dust has a large impact on the earth's radiation balance and climate. The radiative effects of mineral dust depend on factors including, particle size, shape, and composition which can all be extremely complex. Mineral dust particles are typically irregular in shape and can include sharp edges, voids, and fine scale surface roughness. Particle shape can also depend on the type of mineral and can vary as a function of particle size. In addition, atmospheric mineral dust is a complex mixture of different minerals as well as other, possibly organic, components that have been mixed in while these particles are suspended in the atmosphere. Aerosol optical properties are investigated in this work, including studies of the effect of particle size, shape, and composition on the infrared (IR) extinction and visible scattering properties in order to achieve more accurate modeling methods. Studies of particle shape effects on dust optical properties for single component mineral samples of silicate clay and diatomaceous earth are carried out here first. Experimental measurements are modeled using T-matrix theory in a uniform spheroid approximation. Previous efforts to simulate the measured optical properties of silicate clay, using models that assumed particle shape was independent of particle size, have achieved only limited success. However, a model which accounts for a correlation between particle size and shape for the silicate clays offers a large improvement over earlier modeling approaches. Diatomaceous earth is also studied as an example of a single component mineral dust aerosol with extreme particle shapes. A particle shape distribution, determined by fitting the experimental IR extinction data, used as a basis for modeling the visible light scattering properties. While the visible simulations show only modestly good agreement with the scattering data, the fits are generally better than those obtained using more commonly invoked particle shape

Rocks and Minerals.

ERIC Educational Resources Information Center

Naturescope, 1987

1987-01-01

Provides background information on rocks and minerals, including the unique characteristics of each. Teaching activities on rock-hunting and identification, mineral configurations, mystery minerals, and growing crystals are provided. Reproducible worksheets are included for two of the activities. (TW)

Column bioleaching of low-grade mining ore containing high level of smithsonite, talc, sphaerocobaltite and azurite.

PubMed

Ilyas, Sadia; Chi, Ruan; Bhatti, H N; Bhatti, I A; Ghauri, M A

2012-03-01

Present work describes the bioleaching potential of metals from low-grade mining ore containing smithsonite, sphaerocobaltite, azurite and talc as main gangue minerals with adapted consortium of Sulfobacillus thermosulfidooxidans strain-RDB and Thermoplasma acidophilum. Bioleaching potential improved markedly by added energy source, acid preleaching and adaptation of microbial consortium with mixed metal ions. During whole leaching period including acid preleaching stage of 960 h and bioleaching stage of 212 days about 76% Co, 70% Zn, 84% Cu, 72% Ni and 63% Fe leached out.

Agricolaite, a new mineral of uranium from Jáchymov, Czech Republic

NASA Astrophysics Data System (ADS)

Skála, Roman; Ondruš, Petr; Veselovský, František; Císařová, Ivana; Hloušek, Jan

2011-11-01

The new mineral agricolaite, a potassium uranyl carbonate with ideal formula K4(UO2)(CO3)3, occurs in vugs of ankerite gangue in gneisses in the abandoned Giftkiesstollen adit at Jáchymov, Czech Republic. The name is after Georgius Agricola (1494-1555), German scholar and scientist. Agricolaite occurs as isolated equant irregular translucent grains to 0.3 mm with yellow color, pale yellow streak, and vitreous luster. It is brittle with uneven fracture and displays neither cleavage nor parting. Agricolaite is non-fluorescent. Mohs hardness is ~4. It is associated with aragonite, brochantite, posnjakite, malachite, rutherfordine, and "pseudo-voglite". Experimental density is higher than 3.3 g.cm-3, Dcalc is 3.531 g. cm-3. The mineral is monoclinic, space group C2/ c, with a 10.2380(2), b 9.1930(2), c 12.2110(3) Å, β 95.108(2)°, V 1144.71(4) Å3, Z = 4. The strongest lines in the powder X-ray diffraction pattern are d( I)( hkl): 6.061(55)(002), 5.087(57)(200), 3.740(100)(202), 3.393(43)(113), 2.281(52)(402). Average composition based on ten electron microprobe analyses corresponds to (in wt.%) UO3 48.53, K2O 31.49, CO2(calc) 22.04 which gives the empirical formula K3.98(UO2)1.01(CO3)3.00. The crystal structure was solved from single-crystal X-ray diffraction data and refined to R 1 = 0.0184 on the basis of the 1,308 unique reflections with F o > 4 σF o. The structure of agricolaite is identical to that of synthetic K4(UO2)(CO3)3 and consists of separate UO2(CO3)3 groups organized into layers parallel to (100) and two crystallographically non-equivalent sites occupied by K+ cations. Both the mineral and its name were approved by the IMA-CNMNC.

Purification of trona ores by conditioning with an oil-in-water emulsion

DOEpatents

Miller, J. D.; Wang, Xuming; Li, Minhua

2009-04-14

The present invention is a trona concentrate and a process for floating gangue material from trona ore that comprises forming an emulsion, conditioning the trona ore at a high solids content in a saturated trona suspension, and then floating and removing the gangue material. The process for separating trona from gangue materials in trona ore can include emulsifying an oil in an aqueous solution to form an oil-in-water emulsion. A saturated trona suspension having a high solids content can also be formed having trona of a desired particle size. The undissolved trona in the saturated suspension can be conditioned by mixing the saturated suspension and the oil-in-water emulsion to form a conditioning solid suspension of trona and gangue material. A gas can be injected through the conditioning solid suspension to float the gangue material. Thus, the floated gangue material can be readily separated from the trona to form a purified trona concentrate without requirements of additional heat or other expensive processing steps.

A geochemical study of the Sweet Home Mine, Colorado Mineral Belt, USA: hydrothermal fluid evolution above a hypothesized granite cupola

NASA Astrophysics Data System (ADS)

Lüders, Volker; Romer, Rolf L.; Gilg, H. Albert; Bodnar, Robert J.; Pettke, Thomas; Misantoni, Dean

2009-05-01

Deposition of quartz-molybdenite-pyrite-topaz-muscovite-fluorite and subsequent hübnerite and sulfide-fluorite-rhodochrosite mineralization at the Sweet Home Mine occurred coeval with the final stage of magmatic activity and ore formation at the nearby world-class Climax molybdenum deposit about 26 to 25 m.y. ago. The mineralization occurred at depths of about 3,000 m and is related to at least two major fluid systems: (1) one dominated by magmatic fluids, and (2) another dominated by meteoric water. The sulfur isotopic composition of pyrite, strontium isotopes and REY distribution in fluorite suggest that the early-stage quartz-molybdenite-pyrite-topaz-muscovite-fluorite mineral assemblage was deposited from magmatic fluids under a fluctuating pressure regime at temperatures of about 400°C as indicated by CO2-bearing, moderately saline (7.5-12.5 wt.% NaCl equiv.) fluid inclusions. LA-ICPMS analyses of fluid inclusions in quartz demonstrate that fluids from the Sweet Home Mine are enriched in incompatible elements but have considerably lower metal contents than those reported from porphyry-Cu-Au-Mo or Climax-type deposits. The ore-forming fluid exsolved from a highly differentiated magma possibly related to the deep-seated Alma Batholith or distal porphyry stock(s). Sulfide mineralization, marking the periphery of Climax-type porphyry systems, with fluorite and rhodochrosite as gangue minerals was deposited under a hydrostatic pressure regime from low-salinity ± CO2-bearing fluids with low metal content at temperatures below 400°C. The sulfide mineralization is characterized by mostly negative δ34S values for sphalerite, galena, chalcopyrite, and tetrahedrite, highly variable δ18O values for rhodochrosite, and low REE contents in fluorite. The Pb isotopic composition of galena as well as the highly variable 87Sr/86Sr ratios of fluorite, rhodochrosite, and apatite indicates that at least part of the Pb and Sr originated from a much more radiogenic source than

Altered bone material properties in HLA-B27 rats include reduced mineral to matrix ratio and altered collagen cross-links.

PubMed

Gamsjaeger, Sonja; Srivastava, Apurva K; Wergedal, Jon E; Zwerina, Jochen; Klaushofer, Klaus; Paschalis, Eleftherios P; Tatakis, Dimitris N

2014-11-01

Spondyloarthropathy and inflammatory bowel disease (IBD), which includes ulcerative colitis and Crohn's disease, are often associated with severe osteopenia/osteoporosis in both children and adults. HLA-B27 transgenic rats present a phenotype that includes severe colitis and severely accelerated alveolar bone loss. The purpose of this study was to evaluate long bone density status, systemic bone metabolic markers, and intrinsic bone material properties in HLA-B27 transgenic (TG) rats, and compare them with those of age- and sex-matched wild-type (WT) animals. The results indicate that in the HLA-B27 rat, an animal susceptible to both alveolar bone loss (ABL) and long bone osteopenia, there is a statistically significant negative correlation between ABL and long bone bone mineral density (BMD), as well as mineral/matrix ratio at active bone-forming trabecular surfaces. The TG animals had a lower mineral/matrix ratio and higher relative proteoglycan and advanced glycation end product (ϵ-N-Carboxymethyl-L-lysine) content and pyridinoline/divalent collagen cross-link ratio compared with WT. These results may provide better understanding of the interrelationship between osteoporosis and oral bone loss, the underlying causes of the inferior bone strength in the HLA-B27 transgenic animals, and could prove to be a useful model in the elucidation of the pathophysiology of spondyloarthropathy and IBD-associated osteopenia/osteoporosis and in the evaluation of pharmacological intervention(s) against such conditions. © 2014 American Society for Bone and Mineral Research.

The Genesis of Precious and Base Metal Mineralization at the Miguel Auza Deposit, Zacatecas, Mexico

NASA Astrophysics Data System (ADS)

Findley, A. A.; Olivo, G. R.; Godin, L.

2009-05-01

The Miguel Auza mine located in Zacatecas State, Mexico, is a vein-type polymetallic epithermal deposit hosted in deformed argillite, siltstone and, greywacke of the Cretaceous Caracol Formation. Silver-rich base metal veins (0.2 m to >1.5 m wide) are spatially associated with the NE-striking, steeply SE- dipping (70-80°) Miguel Auza fault over a strike length of 1.6 km and a depth of 460 m. A 2 km2 monzonitic stock located in the proximity of the mineralized zones, has previously been interpreted as the source of the mineralizing fluids. Four distinct structural stages are correlated with hydrothermal mineral deposition: (I) The Pre-ore stage is characterized by normal faulting, fracturing of host rock, and rotation of bedding planes. This stage consists of quartz, illite, chlorite, +/- pyrite alteration of sedimentary wall rocks. (II) The Pyrite-vein stage is associated with reverse-sense reactivation of early normal faults, dilation of bedding planes/fractures, and deposition of generally barren calcite + pyrite veinlets. (III) The Main-ore stage is related to the development of reverse-fault- hosted massive sulphide veins. During this stage three phases of mineral deposition are recorded: early pyrite and arsenopyrite, intermediate chalcopyrite, pyrite, arsenopyrite, and base metals, and late base metals and Ag-bearing minerals. Associated gangue minerals during the main ore stage are quartz, muscovite, calcite and chlorite. (IV) The Post-ore stage involves late NW-SE striking block faulting, brecciation and calcite veining. Later supergene oxidation of veins led to deposition of Fe-oxides and hydroxides, commonly filling fractures or replacing early-formed sulphide assemblages. The various vein types display classic epithermal textures including open space filling, banding, comb quartz and brecciation. The Ag-bearing minerals comprise pyrargyrite [Ag3(Sb,As)S3], argentotennantite [(Cu,Ag)10(Zn,Fe)2(Sn,As)4S13], polybasite-pearceite [(Ag,Cu)16(Sb,As)2S11], and

Occurrence of silver minerals in a silver-rich pocket in the massive sulfide zinc-lead ores in the Edwards mine, New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serviss, C.R.; Grout, C.M.; Hagni, R.D.

1985-01-01

Ore microscopic examination of uncommon silver-rich ores from the Edwards mine has detected three silver minerals, native silver, freibergite, and argentite, that were previously unreported in the literature from the Balmat-Edwards district. The zinc-lead ore deposits of the Balmat-Edwards District in northern New York are composed of very coarse-grained massive sulfides, principally sphalerite, galena, and pyrite. The typical ores contain small amounts of silver in solid solution galena. Galena concentrates produced from those ores have contained an average of 15 ounces of silver per ton of 60% lead concentrates. In contrast to the typical ore a silver-rich pocket, that measuredmore » three feet by three feet on the vertical mine face and was the subject of this study, contained nearly 1% silver in a zinc ore. Ore microscopic study shows that this ore is especially characterized by abundant, relatively fine-grained chalcopyrite with anhedral pyrite inclusions. Fine-grained sphalerite, native silver, argentite, freibergite and arsenopyrite occur in association with the chalcopyrite and as fracture-fillings in gangue minerals. Geochemically anomalous amounts of tin, barium, chromium, and nickel also are present in the silver-rich pocket. The silver-rich pocket may mark the locus of an early feeder vent or alternatively it may record a hydrothermal event that was superimposed upon the event responsible for the metamorphic ore textures.« less

Textural and structural evidence for a predeformation hydrothermal origin of the Tungsten Queen Deposit, Hamme District, North Carolina

USGS Publications Warehouse

Foose, M.P.; Slack, J.F.; Casadevall, T.

1980-01-01

The Hamme tungsten district is composed of a series of steeply dipping quartz-wolframite veins in the Piedmont of North Carolina. Veins are concentrated near the border of the lower Paleozoic Vance County pluton, along its western contact with green-schist-facies metapelites and metavolcanic rocks of the Carolina slate belt. One of these quartz veins, the Snead-Walker, hosts the Tungsten Queen deposit. The vein is 0 to 10 m thick and trends N 35 degrees E for approximately 3,500 m through slate belt rocks and the granitic pluton. The deposit has been worked to a depth of nearly 520 m and contains eight en echelon ore lodes that plunge 42 degrees to 65 degrees between S 10 degrees E and S 10 degrees W. Ore lodes commonly are encased in thin lenses of quartz-sericite greisen. The principal ore mineral is huebnerite and is accompanied by scattered occurrences of pyrite, sphalerite, galena, chalcopyrite, and tetrahedrite. The gangue is predominantly quartz with minor amounts of fluorite, sericite, and carbonate.Studies of minor structures and mineral textures indicate that both the wall rock and the ore and gangue minerals within the vein have been deformed by at least two events. The first event produced relatively gentle, open, and shallow-plunging folds; later, an intense episode of right-lateral shearing developed steeply plunging, tight folds and numerous northeast-trending shears. This latter deformation also developed a prominent alignment of ore and gangue minerals oblique to the vein walls and may have formed the en echelon distribution of ore lodes.In relatively undeformed parts of the vein, clusters of euhedral huebnerite crystals are oriented perpendicular to vein layering. Some prismatic crystals have terminations with cappings of sulfides and in polished thin section show concentric growth zones. These features are similar to textures found in unmetamorphosed tungsten-bearing hydrothermal vein deposits such as those at Pasto Bueno, Peru; Carrock Fell

Mineral-deposit model for lithium-cesium-tantalum pegmatites

USGS Publications Warehouse

Bradley, Dwight C.; McCauley, Andrew D.; Stillings, Lisa L.

2017-06-20

Lithium-cesium-tantalum (LCT) pegmatites comprise a compositionally defined subset of granitic pegmatites. The major minerals are quartz, potassium feldspar, albite, and muscovite; typical accessory minerals include biotite, garnet, tourmaline, and apatite. The principal lithium ore minerals are spodumene, petalite, and lepidolite; cesium mostly comes from pollucite; and tantalum mostly comes from columbite-tantalite. Tin ore as cassiterite and beryllium ore as beryl also occur in LCT pegmatites, as do a number of gemstones and high-value museum specimens of rare minerals. Individual crystals in LCT pegmatites can be enormous: the largest spodumene was 14 meters long, the largest beryl was 18 meters long, and the largest potassium feldspar was 49 meters long.Lithium-cesium-tantalum pegmatites account for about one-fourth of the world’s lithium production, most of the tantalum production, and all of the cesium production. Giant deposits include Tanco in Canada, Greenbushes in Australia, and Bikita in Zimbabwe. The largest lithium pegmatite in the United States, at King’s Mountain, North Carolina, is no longer being mined although large reserves of lithium remain. Depending on size and attitude of the pegmatite, a variety of mining techniques are used, including artisanal surface mining, open-pit surface mining, small underground workings, and large underground operations using room-and-pillar design. In favorable circumstances, what would otherwise be gangue minerals (quartz, potassium feldspar, albite, and muscovite) can be mined along with lithium and (or) tantalum as coproducts.Most LCT pegmatites are hosted in metamorphosed supracrustal rocks in the upper greenschist to lower amphibolite facies. Lithium-cesium-tantalum pegmatite intrusions generally are emplaced late during orogeny, with emplacement being controlled by pre-existing structures. Typically, they crop out near evolved, peraluminous granites and leucogranites from which they are inferred to be

Mineral facilities of Europe

USGS Publications Warehouse

Almanzar, Francisco; Baker, Michael S.; Elias, Nurudeen; Guzman, Eric

2010-01-01

This map displays over 1,700 records of mineral facilities within the countries of Europe and western Eurasia. Each record represents one commodity and one facility type at a single geographic location. Facility types include mines, oil and gas fields, and plants, such as refineries, smelters, and mills. Common commodities of interest include aluminum, cement, coal, copper, gold, iron and steel, lead, nickel, petroleum, salt, silver, and zinc. Records include attributes, such as commodity, country, location, company name, facility type and capacity (if applicable), and latitude and longitude geographical coordinates (in both degrees-minutes-seconds and decimal degrees). The data shown on this map and in table 1 were compiled from multiple sources, including (1) the most recently available data from the U.S. Geological Survey (USGS) Minerals Yearbook (Europe and Central Eurasia volume), (2) mineral statistics and information from the USGS Minerals Information Web site (http://minerals.usgs.gov/minerals/pubs/country/europe.html), and (3) data collected by the USGS minerals information country specialists from sources, such as statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Data reflect the most recently published table of industry structure for each country at the time of this publication. Additional information is available from the country specialists listed in table 2.

Preliminary report on the geology and deposits of monazite, thorite and niobium-bearing rutile of the Mineral Hill district, Lemhi County, Idaho

USGS Publications Warehouse

Kaiser, Edward Peck

1956-01-01

Deposits of minerals containing niobium (columbium), thorium, and rare earths occur in the Mineral Hill district, 30 miles northwest of Salmon, Lemhi County, Idaho. Monazite, thorite, allanite, and niobium-bearing rutile form deposits in metamorphic limestone layers less than 8 feet thick. The known deposits are small, irregular, and typically located in or near small folds. Minor faults are common. Monazite generally is coarsely crystalline and contains less than one percent thorium. Rutile forms massive lumps up to 3 inches across; it contains between 5 and 10 percent niobium. Rutile occurs in the northwestern half of the district, thorite in the central and southeastern parts. Monazite occurs in all deposits. Allanite is locally abundant and contains several percent thorium. Magnetite and ilmenite are also locally abundant. A major thrust fault trending northwest across the map-area separates moderately folded quartzite and phyllitic rocks of Belt age, on the northeast, from more intensely metamorphosed and folded rocks on the southwest. The more metamorphosed rocks include amphibolite, porphyroblastic feldspar gneiss, quartzite, and limestone, all probably of sedimentary origin, and probably also of Belt (late Precambrian) age. The only rocks of definite igneous origin are rhyolite dikes of probable Tertiary age. The more metamorphosed rocks were formed by metasomatic metamorphism acting on clastic sediments, probably of Belt age, although they may be older than Belt. Metamorphism doubtless was part of the episode of emplacement of the Idaho batholith, but the history of that episode is not well understood. The rare-element deposits show no evidence of fracture-controlled hydrothermal introduction, such as special fracture systems, veining, and gangue material. They may, however, be of hydrothermal type. More likely they are metamorphic segregations or secretions, deposited in favorable stratigraphic and structural positions during regional metamorphism.

Modèle de formation du gisement d'argent d'Imiter (Anti-Atlas oriental, Maroc). Nouveaux apports de l'analyse structurale et minéralogique

NASA Astrophysics Data System (ADS)

Tuduri, Johann; Chauvet, Alain; Ennaciri, Aomar; Barbanson, Luc

2006-03-01

Based on a combined geometrical and mineralogical analysis, a three-stage model of formation of the mineralized veins of the giant Imiter silver deposit (Anti-Atlas, Morocco) is herein proposed. A first episode is characterized by the development of quartz, pink dolomite and Ag-rich minerals veins formed during a dextral transpressive event. The second episode is associated with a normal left-lateral motion that re-opens previous structures, filled by pink dolomite gangue. Alteration stages contribute to a local Ag enrichment. To cite this article: J. Tuduri et al., C. R. Geoscience 338 (2005).

Mineral commodity summaries 2013

USGS Publications Warehouse

,

2013-01-01

Each chapter of the 2013 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2012 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. For mineral commodities for which there is a Government stockpile, detailed information concerning the stockpile status is included in the two-page synopsis. Abbreviations and units of measure, and definitions of selected terms used in the report, are in Appendix A and Appendix B, respectively. “Appendix C—Reserves and Resources” includes “Part A—Resource/Reserve Classification for Minerals” and “Part B—Sources of Reserves Data.” A directory of USGS minerals information country specialists and their responsibilities is Appendix D. The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the MCS 2013 are welcomed.

Mineral commodity summaries 2014

USGS Publications Warehouse

,

2014-01-01

Each chapter of the 2014 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2013 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. For mineral commodities for which there is a Government stockpile, detailed information concerning the stockpile status is included in the two-page synopsis. Abbreviations and units of measure, and definitions of selected terms used in the report, are in Appendix A and Appendix B, respectively. “Appendix C—Reserves and Resources” includes “Part A—Resource/Reserve Classification for Minerals” and “Part B—Sources of Reserves Data.” A directory of USGS minerals information country specialists and their responsibilities is Appendix D. The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the MCS 2014 are welcomed.

Bartering for Minerals.

ERIC Educational Resources Information Center

May, Kathie

2002-01-01

Presents an activity in which students are assigned occupations that rely on specific minerals. To obtain the needed minerals, students learn how to trade services and commodities. Includes details on preparation, modeling behaviors, and printed materials. (DDR)

Mineral Fiber Toxicology

EPA Science Inventory

The chemical and physical properties of different forms of mineral fibers impact biopersistence and pathology in the lung. Fiber chemistry, length, aspect ratio, surface area and dose are critical factors determining mineral fiber-associated health effects including cancer and as...

Polycyclic aromatic hydrocarbons (PAHs) in multimedia environment of Heshan coal district, Guangxi: distribution, source diagnosis and health risk assessment.

PubMed

Huang, Huan-Fang; Xing, Xin-Li; Zhang, Ze-Zhou; Qi, Shi-Hua; Yang, Dan; Yuen, Dave A; Sandy, Edward H; Zhou, Ai-Guo; Li, Xiao-Qian

2016-10-01

Mining activities are among the major culprits of the wide occurrences of soil and water pollution by PAHs in coal district, which have resulted in ecological fragilities and health risk for local residents. Sixteen PAHs in multimedia environment from the Heshan coal district of Guangxi, South China, were measured, aiming to investigate the contamination level, distribution and possible sources and to estimate the potential health risks of PAHs. The average concentrations of 16 PAHs in the coal, coal gangue, soil, surface water and groundwater were 5114.56, 4551.10, 1280.12 ng g(-1), 426.98 and 381.20 ng L(-1), respectively. Additionally, higher soil and water PAH concentrations were detected in the vicinities of coal or coal gangue dump. Composition analysis, isomeric ratio, Pearson correlation analysis and principal component analysis were performed to diagnose the potential sources of PAHs in different environmental matrices, suggesting the dominant inputs of PAHs from coal/coal combustion and coal gangue in the soil and water. Soil and water guidelines and the incremental lifetime risk (ICLR) were used to assess the health risk, showing that soil and water were heavily contaminated by PAHs, and mean ICLRcoal/coal-gangue and mean ICLRsoil were both significantly higher than the acceptable levels (1 × 10(-4)), posing high potential carcinogenic risk to residents, especially coal workers. This study highlights the environmental pollution problems and public health concerns of coal mining, particularly the potential occupational health hazards of coal miners exposed in Heshan.

Chemical composition and evolution of tourmaline-supergroup minerals from the Sb hydrothermal veins in Rožňava area, Western Carpathians, Slovakia

NASA Astrophysics Data System (ADS)

Bačík, Peter; Dikej, Jakub; Fridrichová, Jana; Miglierini, Marcel; Števko, Martin

2017-09-01

Tourmaline-supergroup minerals are common gangue minerals in Sb-hydrothermal veins on Betliar - Straková, Čučma - Gabriela and Rožňava - Peter-Pavol vein deposits in the Rožňava area, Slovakia. Tourmaline-supergroup minerals form relatively large prismatic to radial aggregates of parallel black to greyish-black crystals. Tourmaline-supergroup minerals from Betliar - Straková and Rožňava - Peter-Pavol are almost homogeneous with intermediate schorl-dravite composition. Čučma - Gabriela tourmaline have distinct zoning with massive core of the schorlitic-to-feruvitic shifting to schorlitic-to-dravitic composition, and dravitic to magnesio-foititic rim. The tourmaline composition is influenced by two main substitutions, namely Ca(Mg,Fe)Na-1Al-1 and X □AlNa-1(Mg,Fe)-1. Betliar - Straková and Rožňava - Peter-Pavol tourmaline-supergroup minerals exhibit only small extents of the X □AlNa-1(Mg,Fe)-1 substitution. This substitution shifts the composition to magnesio-foitite in Čučma - Gabriela tourmaline. The decrease of Al in the core of Čučma - Gabriela tourmaline crystals is caused by extensive Ca(Mg,Fe)Na-1Al-1 substitution. The unit-cell dimensions of all investigated tourmaline-supergroup minerals indicate an octahedral disorder with the Z (Fe3++Mg) proportion calculated from empirical equations varying between 0.85 and 0.87 apfu (atoms per formula unit). Based on Mössbauer spectra, the Z Fe3+ content varied between 0.25 apfu in Betliar - Straková tourmaline and 0.45 apfu in Čučma - Gabriela sample. Based on Fe/(Fe + Mg) ratio, Betliar - Straková tourmaline is slightly enriched in Fe compared to Rožňava - Peter-Pavol, suggesting the impact of the host-rock composition; first are grown in Fe-richer acidic metarhyolitic rocks, latter in metapelites. In Čučma - Gabriela, the variations in Fe/(Fe + Mg) are very likely reflecting the change in fluid composition. Magnesio-foitite is the product of second-stage crystallization forming rims and

Paleozoic magmatism and porphyry Cu-mineralization in an evolving tectonic setting in the North Qilian Orogenic Belt, NW China

NASA Astrophysics Data System (ADS)

Qiu, Kun-Feng; Deng, Jun; Taylor, Ryan D.; Song, Kai-Rui; Song, Yao-Hui; Li, Quan-Zhong; Goldfarb, Richard J.

2016-05-01

The NWW-striking North Qilian Orogenic Belt records the Paleozoic accretion-collision processes in NW China, and hosts Paleozoic Cu-Pb-Zn mineralization that was temporally and spatially related to the closure of the Paleo Qilian-Qinling Ocean. The Wangdian Cu deposit is located in the eastern part of the North Qilian Orogenic Belt, NW China. Copper mineralization is spatially associated with an altered early Paleozoic porphyritic granodiorite, which intruded tonalites and volcaniclastic rocks. Alteration zones surrounding the mineralization progress outward from a potassic to a feldspar-destructive phyllic assemblage. Mineralization consists mainly of quartz-sulfide stockworks and disseminated sulfides, with ore minerals chalcopyrite, pyrite, molybdenite, and minor galena and sphalerite. Gangue minerals include quartz, orthoclase, biotite, sericite, and K-feldspar. Zircon LA-ICPMS U-Pb dating of the ore-bearing porphyritic granodiorite yielded a mean 206Pb/238U age of 444.6 ± 7.8 Ma, with a group of inherited zircons yielding a mean U-Pb age of 485 ± 12 Ma, consistent with the emplacement age (485.3 ± 6.2 Ma) of the barren precursor tonalite. Rhenium and osmium analyses of molybdenite grains returned model ages of 442.9 ± 6.8 Ma and 443.3 ± 6.2 Ma, indicating mineralization was coeval with the emplacement of the host porphyritic granodiorite. Rhenium concentrations in molybdenite (208.9-213.2 ppm) suggest a mantle Re source. The tonalities are medium-K calc-alkaline. They are characterized by enrichment of light rare-earth elements (LREEs) and large-ion lithophile elements (LILEs), depletion of heavy rare-earth elements (HREEs) and high-field-strength elements (HFSEs), and minor negative Eu anomalies. They have εHf(t) values in the range of +3.6 to +11.1, with two-stage Hf model ages of 0.67-1.13 Ga, suggesting that the ca. 485 Ma barren tonalites were products of arc magmatism incorporating melts from the mantle wedge and the lithosphere. In contrast, the

Underground mineral extraction

NASA Technical Reports Server (NTRS)

Miller, C. G.; Stephens, J. B.

1980-01-01

A method was developed for extracting underground minerals such as coal, which avoids the need for sending personnel underground and which enables the mining of steeply pitched seams of the mineral. The method includes the use of a narrow vehicle which moves underground along the mineral seam and which is connected by pipes or hoses to water pumps at the surface of the Earth. The vehicle hydraulically drills pilot holes during its entrances into the seam, and then directs sideward jets at the seam during its withdrawal from each pilot hole to comminute the mineral surrounding the pilot hole and combine it with water into a slurry, so that the slurried mineral can flow to a location where a pump raises the slurry to the surface.

Changes in bone mineral metabolism parameters, including FGF23, after discontinuing cinacalcet at kidney transplantation.

PubMed

Barros, Xoana; Fuster, David; Paschoalin, Raphael; Oppenheimer, Federico; Rubello, Domenico; Perlaza, Pilar; Pons, Francesca; Torregrosa, Jose V

2015-05-01

Little is known about the effects of the administration of cinacalcet in dialytic patients who are scheduled for kidney transplantation, and in particular about the changes in FGF23 and other mineral metabolism parameters after surgery compared with recipients not on cinacalcet at kidney transplantation. We performed a prospective observational cohort study with recruitment of consecutive kidney transplant recipients at our institution. Patients were classified according to whether they were under treatment with cinacalcet before transplantation. Bone mineral metabolism parameters, including C-terminal FGF23, were measured at baseline, on day 15, and at 1, 3, and 6 months after transplantation. In previously cinacalcet-treated patients, cinacalcet therapy was discontinued on the day of surgery and was not restarted after transplantation. A total of 48 kidney transplant recipients, 20 on cinacalcet at surgery and 28 cinacalcet non-treated patients, completed the follow-up. Serum phosphate declined significantly in the first 15 days after transplantation with no differences between the two groups, whereas cinacalcet-treated patients showed higher FGF23 levels, although not significant. After transplantation, PTH and serum calcium were significantly higher in cinacalcet-treated patients. We conclude that patients receiving cinacalcet on dialysis presented similar serum phosphate levels but higher PTH and serum calcium levels during the initial six months after kidney transplantation than cinacalcet non-treated patients. The group previously treated with cinacalcet before transplantation showed higher FGF23 levels without significant differences, so further studies should investigate its relevance in the management of these patients.

Clay Minerals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mueller, Karl T.; Sanders, Rebecca L.; Washton, Nancy M.

2014-03-14

Clay minerals are important components of the environment and are involved or implicated in processes such as the uptake of pollutants and the release of nutrients and as potential platforms for a number of chemical reactions. Owing to their small particle sizes (typically, on the order of microns or smaller) and mixing with a variety of other minerals and soil components, advanced characterization methods are needed to study their structures, dynamics, and reactivities. In this article, we describe the use of solid-state NMR methods to characterize the structures and chemistries of clay minerals. Early one-pulse magic-angle spinning (MAS) NMR studiesmore » of 27Al and 29Si have now been enhanced and extended with new studies utilizing advanced methodologies (such as Multiple Quantum MAS) as well as studies of less-sensitive nuclei. In additional work, the issue of reactivity of clay minerals has been addressed, including studies of reactive surface area in the environment. Utilizations of NMR-sensitive nuclides within the clay minerals themselves, and in molecules that react with specific sites on the clay mineral surfaces, have aided in understanding the reactivity of these complex aluminosilicate systems.« less

Mineral Facilities of Latin America and Canada

USGS Publications Warehouse

Bernstein, Rachel; Eros, Mike; Quintana-Velazquez, Meliany

2006-01-01

This data set consists of records for over 900 mineral facilities in Latin America and Canada. The mineral facilities include mines, plants, smelters, or refineries of aluminum, cement, coal, copper, diamond, gold, iron and steel, nickel, platinum-group metals, salt, and silver, among others. Records include attributes such as commodity, country, location, company name, facility type and capacity if applicable, and generalized coordinates. The data were compiled from multiple sources, including the 2003 and 2004 USGS Minerals Yearbooks (Latin America and Candada volume), data to be published in the 2005 Minerals Yearbook Latin America and Canada Volume, minerals statistics and information from the USGS minerals information Web site (minerals.usgs.gov/minerals), and data collected by USGS minerals information country specialists. Data reflect the most recent published table of industry structure for each country. Other sources include statistical publications of individual countries, annual reports and press releases of operating companies,and trade journals. Due to the sensitivity of some energy commodity data, the quality of these data should be evaluated on a country-by-country basis. Additional information and explanation is available from the country specialists.

75 FR 64411 - Lowering Miners' Exposure to Respirable Coal Mine Dust, Including Continuous Personal Dust Monitors

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-19

...The Mine Safety and Health Administration (MSHA) proposes to lower miners' exposure to respirable coal mine dust by revising the Agency's existing standards on miners' occupational exposure to respirable coal mine dust. The major provisions of the proposal would lower the existing exposure limit; provide for full-shift sampling; redefine the term ``normal production shift; '' and add reexamination and decertification requirements for persons certified to sample, and maintain and calibrate sampling devices. In addition, the proposed rule would provide for single shift compliance sampling under the mine operator and MSHA's inspector sampling programs, and would establish sampling requirements for use of the Continuous Personal Dust Monitor (CPDM) and expanded requirements for medical surveillance. The proposed rule would significantly improve health protections for this Nation's coal miners by reducing their occupational exposure to respirable coal mine dust and lowering the risk that they will suffer material impairment of health or functional capacity over their working lives.

Dissolution Rates and Mineral Lifetimes of Phosphate Containing Minerals and Implications for Mars

NASA Astrophysics Data System (ADS)

Adcock, C. T.; Hausrath, E.

2011-12-01

The objectives of NASA's Mars Exploration Program include exploring the planet's habitability and the possibility of past, present, or future life. This includes investigating "possible supplies of bioessential elements" [1]. Phosphate is one such bioessential element for life as we understand it. Phosphate is also abundant on Mars [2], and the phosphate rich minerals chlorapatite, fluorapatite, and merrillite have been observed in Martian meteorites [3]. Surface rock analyses from the MER Spirit also show the loss of a phosphate rich mineral from the rocks Wishstone and Watchtower at Gusev Crater [4,5], implying mineral dissolution. Dissolution rates of phosphate containing minerals are therefore important for characterizing phosphate mobility and bioavailability on Mars. Previous studies have measured dissolution rates of fluorapatite [6-8]. However, chlorapatite and merrillite (a non-terrestrial mineral similar to whitlockite) are more common phosphate minerals found in Martian meteorites [3], and few dissolution data exist for these minerals. We have begun batch dissolution experiments on chlorapatite, synthesized using methods of [9], and whitlockite, synthesized using a method modified from [10]. Additionally, we are dissolving Durango fluorapatite to compare to dissolution rates in literature, and natural Palermo whitlockite to compare to dissolution rates of our synthesized whitlockite. Batch dissolution experiments were performed after [8], using a 0.01 molar KNO3 solution with 0.1500g-0.3000g mineral powders and starting solution volumes of 180ml in LDPE reaction vessels. HNO3 or KOH were used to adjust initial pH as required. Dissolution rates are calculated from the rate of change of elemental concentration in solution as a function of time, and normalized to the mineral surface area as measured by BET. Resulting rates will be used to calculate mineral lifetimes for the different phosphate minerals under potential Mars-like aqueous conditions, and in

Exploiting mineral data: applications to the diversity, distribution, and social networks of copper mineral

NASA Astrophysics Data System (ADS)

Morrison, S. M.; Downs, R. T.; Golden, J. J.; Pires, A.; Fox, P. A.; Ma, X.; Zednik, S.; Eleish, A.; Prabhu, A.; Hummer, D. R.; Liu, C.; Meyer, M.; Ralph, J.; Hystad, G.; Hazen, R. M.

2016-12-01

We have developed a comprehensive database of copper (Cu) mineral characteristics. These data include crystallographic, paragenetic, chemical, locality, age, structural complexity, and physical property information for the 689 Cu mineral species approved by the International Mineralogical Association (rruff.info/ima). Synthesis of this large, varied dataset allows for in-depth exploration of statistical trends and visualization techniques. With social network analysis (SNA) and cluster analysis of minerals, we create sociograms and chord diagrams. SNA visualizations illustrate the relationships and connectivity between mineral species, which often form cliques associated with rock type and/or geochemistry. Using mineral ecology statistics, we analyze mineral-locality frequency distribution and predict the number of missing mineral species, visualized with accumulation curves. By assembly of 2-dimensional KLEE diagrams of co-existing elements in minerals, we illustrate geochemical trends within a mineral system. To explore mineral age and chemical oxidation state, we create skyline diagrams and compare trends with varying chemistry. These trends illustrate mineral redox changes through geologic time and correlate with significant geologic occurrences, such as the Great Oxidation Event (GOE) or Wilson Cycles.

Evidence for Late-Paleozoic brine migration in Cambrian carbonate rocks of the central and southern Appalachians: Implications for Mississippi Valley-type sulfide mineralization

USGS Publications Warehouse

Hearn, P.P.; Sutter, J.F.; Belkin, H.E.

1987-01-01

Many Lower Paleozoic limestones and dolostones in the Valley and Ridge province of the central and southern Appalachians contain 10 to 25 weight percent authigenic potassium feldspar. This was considered to be a product of early diagenesis, however, 40Ar 39Ar analyses of overgrowths on detrital K-feldspar in Cambrian carbonate rocks from Pennsylvania, Maryland, Virginia, and Tennessee yield Late Carboniferous-Early Permian ages (278-322 Ma). Simple mass balance calculations suggest that the feldspar could not have formed isochemically, but required the flux of multiple pore volumes of fluid through the rocks, reflecting regional fluid migration events during the Late-Paleozoic Alleghanian orogeny. Microthermometric measurements of fluid inclusions in overgrowths on detrital K-feldspar and quartz grains from unmineralized rocks throughout the study area indicate homogenization temperatures from 100?? to 200??C and freezing point depressions of -14?? to -18.5??C (18-21 wt.% NaCl equiv). The apparent similarity of these fluids to fluid inclusions in ore and gangue minerals of nearby Mississippi Valley-type (MVT) deposits suggests that the regional occurrences of authigenic K-feldspar and MVT mineralization may be genetically related. This hypothesis is supported by the discovery of authigenic K-feldspar intergrown with sphalerite in several mines of the Mascot-Jefferson City District, E. Tennessee. Regional potassic alteration in unmineralized carbonate rocks and localized occurrences of MVT mineralization are both explainable by a gravity-driven flow model, in which deep brines migrate towards the basin margin under a hydraulic gradient established during the Alleghanian orogeny. The authigenic K-feldspar may reflect the loss of K during disequilibrium cooling of the ascending brines. MVT deposits are probably localized manifestations of the same migrating fluids, occurring where the necessary physical and chemical traps are present. ?? 1987.

Mineral types of hydrothermal alteration zones in the Dukat ore field and their relationships to leucogranite and epithermal gold-silver ore, northeastern Russia

NASA Astrophysics Data System (ADS)

Filimonova, L. G.; Trubkin, N. V.; Chugaev, A. V.

2014-05-01

The paper considers the localization of potassic and propylitic hydrothermal alteration zones in the domal volcanic-plutonic structure controlling the position of the Dukat ore field with the eponymous unique epithermal Au-Ag deposit. Comprehensive mineralogical and geochemical data on rocks and minerals in hydrothermal alteration zones and associated intrusions have shown that quartz-jarosite-sericite, quartz-pyrite-sericite, and quartz-adularia-chlorite alterations were formed with the participation of fluid flows related to a fingerlike projection of a high-K leucogranite porphyry intrusion with large phenocrysts. These hydrothermal alterations developed in the rifted graben under conditions of divergent plate boundaries, whereas quartz-clinozoisite-calcite, epidote-chlorite, and garnet-calcite-chlorite alterations were linked to K-Na leucogranite intrusive bodies and developed under conditions of convergent plate boundaries reactivated as a result of formation of the marginal Okhotsk-Chukotka volcanic belt. Phase separation and coagulation of specific portions of ascending fluids resulted in the formation and stabilization of small-sized particles of native silver and other ore components, which enabled involvement in flows of secondary geothermal solutions and ore-forming fluids. The Sr, Nd, and Pb isotopic compositions of rocks and minerals from the hydrothermal alteration zones, associated intrusions, and economic orebodies at the Dukat deposit indicate that their components have been derived from the juvenile continental crust, which was altered in pre-Cretaceous periods of endogenic activity. The components of gangue minerals of potassic and propylitic hydrothertmal alterations and associated intrusions have been taken from deep sources differing in 87Sr/86Sr and 143Nd/144Nd at similar U/Pb and Th/Pb ratios. Chalcophile lead in products of hydrothermal activity and melanocratic inclusions in leucogranite has been taken from regions with elevated U/Pb and

Tourmaline in Appalachian - Caledonian massive sulphide deposits and its exploration significance.

USGS Publications Warehouse

Slack, J.F.

1982-01-01

Tourmaline is a common gangue mineral in several types of stratabound mineral deposits, including some massive base-metal sulphide ores of the Appalachian - Caledonian orogen. It is most abundant (sometimes forming massive foliated tourmalinite) in sediment-hosted deposits, such as those at the Elizabeth Cu mine and the Ore Knob Cu mine (North Carolina, USA). Trace amounts of tourmaline occur associated with volcanic-hosted deposits in the Piedmont and New England and also in the Trondheim district. Tourmaline associated with the massive sulphide deposits are Mg- rich dravites with major- and trace-element compositions significantly different from schorl. It is suggested that the necessary B was produced by submarine exhalative processes as a part of the same hydrothermal system that deposited the ores. An abundance of dravite in non-evaporitic terrains is believed to indicate proximity to former subaqueous fumarolic centres.-R.A.H.

Mineral facilities of Africa and the Middle East

USGS Publications Warehouse

Eros, J.M.; Candelario-Quintana, Luissette

2006-01-01

This map displays over 1,500 mineral facilities in Africa and the Middle East. The mineral facilities include mines, plants, mills, or refineries of aluminum, cement, coal, copper, diamond, gold, iron and steel, nickel, platinum-group metals, salt, and silver, among others. The data used in this poster were compiled from multiple sources, including the 2004 USGS Minerals Yearbook (Africa and Middle East volume), Minerals Statistics and Information from the USGS Web site (http://minerals.usgs.gov/minerals/), and data collected by USGS minerals information country specialists. Data reflect the most recent published table of industry structure for each country. Other sources include statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Due to the sensitivity of some energy commodity data, the quality of these data should be evaluated on a country-by-country basis. Additional information and explanation is available from the country specialists. See Table 1 for general information about each mineral facility site including country, location and facility name, facility type, latitude, longitude, mineral commodity, mining method, main operating company, status, capacity, and units.

Microorganisms meet solid minerals: interactions and biotechnological applications.

PubMed

Ng, Daphne H P; Kumar, Amit; Cao, Bin

2016-08-01

In natural and engineered environments, microorganisms often co-exist and interact with various minerals or mineral-containing solids. Microorganism-mineral interactions contribute significantly to environmental processes, including biogeochemical cycles in natural ecosystems and biodeterioration of materials in engineered environments. In this mini-review, we provide a summary of several key mechanisms involved in microorganism-mineral interactions, including the following: (i) solid minerals serve as substrata for biofilm development; (ii) solid minerals serve as an electron source or sink for microbial respiration; (iii) solid minerals provide microorganisms with macro or micronutrients for cell growth; and (iv) (semi)conductive solid minerals serve as extracellular electron conduits facilitating cell-to-cell interactions. We also highlight recent developments in harnessing microbe-mineral interactions for biotechnological applications.

Base and precious metal occurrences along the San Andreas Fault, Point Delgada, California

USGS Publications Warehouse

McLaughlin, Robert J.; Sorg, D.H.; Ohlin, H.N.; Heropoulos, Chris

1979-01-01

Previously unrecognized veins containing lead, zinc, and copper sulfide minerals at Point Delgada, Calif., are associated with late Mesozoic(?) and Tertiary volcanic and sedimentary rocks of the Franciscan assemblage. Sulfide minerals include pyrite, sphalerite, galena, and minor chalcopyrite, and galena-rich samples contain substantial amounts of silver. These minerals occur in a quartz-carbonate gangue along northeast-trending faults and fractures that exhibit (left?) lateral and vertical slip. The sense of fault movement and the northeasterly strike are consistent with predicted conjugate fault sets of the present San Andreas fault system. The sulfide mineralization is younger than the Franciscan rocks of Point Delgada and King Range, and it may have accompanied or postdated the inception of San Andreas faulting. Mineralization largely preceded uplift, the formation of a marine terrace, and the emplacement of landslide-related debris-flow breccias that overlie the mineralized rocks and truncate the sulfide veins. These field relations indicate that the sulfide mineralization and inception of San Andreas faulting were clearly more recent than the early Miocene and that the mineralization could be younger than about 1.2 m.y. The sulfide veins at Point Delgada may be of economic significance. However, prior to any exploitation of the occurrence, economic and environmental conflicts of interest involving private land ownership, the Shelter Cove home development, and proximity of the coast must be resolved.

Paleozoic magmatism and porphyry Cu-mineralization in an evolving tectonic setting in the North Qilian Orogenic Belt, NW China

USGS Publications Warehouse

Qiu, Kun-Feng; Deng, Jun; Taylor, Ryan D.; Song, Kai-Rui; Song, Yao-Hui; Li, Quan-Zhong; Goldfarb, Richard J.

2016-01-01

The NWW-striking North Qilian Orogenic Belt records the Paleozoic accretion–collision processes in NW China, and hosts Paleozoic Cu–Pb–Zn mineralization that was temporally and spatially related to the closure of the Paleo Qilian-Qinling Ocean. The Wangdian Cu deposit is located in the eastern part of the North Qilian Orogenic Belt, NW China. Copper mineralization is spatially associated with an altered early Paleozoic porphyritic granodiorite, which intruded tonalites and volcaniclastic rocks. Alteration zones surrounding the mineralization progress outward from a potassic to a feldspar-destructive phyllic assemblage. Mineralization consists mainly of quartz-sulfide stockworks and disseminated sulfides, with ore minerals chalcopyrite, pyrite, molybdenite, and minor galena and sphalerite. Gangue minerals include quartz, orthoclase, biotite, sericite, and K-feldspar. Zircon LA-ICPMS U–Pb dating of the ore-bearing porphyritic granodiorite yielded a mean 206Pb/238U age of 444.6 ± 7.8 Ma, with a group of inherited zircons yielding a mean U–Pb age of 485 ± 12 Ma, consistent with the emplacement age (485.3 ± 6.2 Ma) of the barren precursor tonalite. Rhenium and osmium analyses of molybdenite grains returned model ages of 442.9 ± 6.8 Ma and 443.3 ± 6.2 Ma, indicating mineralization was coeval with the emplacement of the host porphyritic granodiorite. Rhenium concentrations in molybdenite (208.9–213.2 ppm) suggest a mantle Re source. The tonalities are medium-K calc-alkaline. They are characterized by enrichment of light rare-earth elements (LREEs) and large-ion lithophile elements (LILEs), depletion of heavy rare-earth elements (HREEs) and high-field-strength elements (HFSEs), and minor negative Eu anomalies. They have εHf(t) values in the range of +3.6 to +11.1, with two-stage Hf model ages of 0.67–1.13 Ga, suggesting that the ca. 485 Ma barren tonalites were products of arc magmatism incorporating melts from the mantle wedge and

Mineral Selection for Multicomponent Equilibrium Geothermometry

DOE PAGES

Plamer, C. D.; Ohly, S. R.; Smith, R. W.; ...

2015-04-01

Multicomponent geothermometry requires knowledge of the mineral phases in the reservoir with which the geothermal fluids may be equilibrated. These minerals phases are most often alteration products rather than primary minerals. We have reviewed the literature on geothermal systems representing most major geologic environments typically associated with geothermal activity and identified potential alteration products in various environments. We have included this information in RTEst, a code we have developed to estimate reservoir conditions (temperature, CO 2 fugacity) from the geochemistry of near-surface geothermal waters. The information has been included in RTEst through the addition of filters that decrease the potentialmore » number of minerals from all possibilities based on the basis species to those that are more relevant to the particular conditions in which the user is interested. The three groups of filters include host rock type (tholeiitic, calc-alkaline, silicic, siliciclastic, carbonate), water type (acidic, neutral), and the temperature range over which the alteration minerals were formed (low, medium, high). The user-chosen mineral assemblage is checked to make sure that it does not violate the Gibbs phase rule. The user can select one of three mineral saturation weighting schemes that decrease the chance the optimization from being skewed by reaction stoichiometry or analytical uncertainty.« less

Digging into Minnesota Minerals.

ERIC Educational Resources Information Center

Minnesota State Dept. of Natural Resources, St. Paul.

This publication presents students with facts about geology and several learning activities. Topics covered include rocks and minerals, volcanoes and earthquakes, fossils, exploration geology, mining in Minnesota, environmental issues related to mining, mineral uses, mining history, and the geology of Minnesota's state parks. A geologic timetable…

Mineral facilities of Asia and the Pacific

USGS Publications Warehouse

Baker, Michael S.; Elias, Nurudeen; Guzman, Eric; Soto-Viruet, Yadira

2010-01-01

This map displays over 1,500 records of mineral facilities throughout the continent of Asia and the countries of the Pacific Ocean. Each record represents one commodity and one facility type at a single geographic location. Facility types include mines, oil and gas fields, and plants, such as refineries, smelters, and mills. Common commodities of interest include aluminum, cement, coal, copper, gold, iron and steel, lead, nickel, petroleum, salt, silver, and zinc. Records include attributes, such as commodity, country, location, company name, facility type and capacity (if applicable), and latitude and longitude geographical coordinates (in both degrees-minutes-seconds and decimal degrees). The data shown on this map and in table 1 were compiled from multiple sources, including (1) the 2008 U.S. Geological Survey Minerals Yearbook (Asia and the Pacific volume), (2) minerals statistics and information from the U.S. Geological Survey Minerals Information Web site (http://minerals.usgs.gov/minerals/), and (3) data collected by U.S. Geological Survey minerals information country specialists. Other sources include statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Due to the sensitivity of some energy commodity data, the quality of these data should be evaluated on a country-by-country basis. Additional information is available from the country specialists listed in table 2.

Raman Spectroscopic Characterisation of Australian Banded Iron Formation and Iron Ore

NASA Astrophysics Data System (ADS)

Wells, M. A.; Ramanaidou, E. R.

2012-04-01

In Australia and world-wide over the past 5-10 years, declining reserves of premium, high-grade (>64% Fe), low-P bearing iron ore, have seen iron ore producers increase their utilisation of lower Fe-grade, higher P/Al/Si ore. In Australia, the channel iron deposits (CID), bedded iron deposits (BID) and, more recently, BIF-derived magnetite iron deposits (MID) have seen increased usage driven mainly by the increased demand from Chinese steel mills (Ramanaidou and Wells, 2011). Efficient exploitation and processing of these lower-grade iron ores requires a detailed understanding of their iron oxide and gangue mineralogy and geochemistry. The common Fe-bearing minerals (e.g., hematite, magnetite, goethite and kenomagnetite) in these deposits, as well as gangue minerals such as quartz and carbonates, are all strongly Raman active (e.g., de Faria et al., 1997). Their distinct Raman spectra enable them to be easily detected and mapped in situ in either unprepared material or samples prepared as polished blocks. In this paper, using representative examples of Australian CID ore, martite-goethite bedded iron deposit (BID) ore and banded iron formation (BIF) examined as polished blocks, we present a range of Raman spectra of the key iron ore minerals, and discuss how Raman spectroscopy can be applied to characterising iron ore mineralogy. Raman imaging micrographs, obtained using a StreamLine Plus Raman imaging system, clearly identified the main Fe-oxide and gangue components in the CID, BID and BIF samples when compared to optical micrographs. Raman analysis enabled the unequivocal identification of diamond in the CID ore as a contaminant from the polishing paste used to prepare the sample, and confirmed the presence of hematite in the BID ore in the form of martite, which can be morphologically similar to magnetite and, thus, difficult to otherwise distinguish. Image analysis of Raman mineral maps could be used to quantify mineral abundance based on the number of 'pixels

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 2 2012-07-01 2012-07-01 false Mineral material operations... NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material... officer may approve contracts and permits for the sale or other disposal of mineral materials, including...

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 2 2014-07-01 2014-07-01 false Mineral material operations... NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material... officer may approve contracts and permits for the sale or other disposal of mineral materials, including...

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 2 2011-07-01 2011-07-01 false Mineral material operations... NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material... officer may approve contracts and permits for the sale or other disposal of mineral materials, including...

36 CFR 292.68 - Mineral material operations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 2 2013-07-01 2013-07-01 false Mineral material operations... NATIONAL RECREATION AREAS Smith River National Recreation Area Mineral Materials § 292.68 Mineral material... officer may approve contracts and permits for the sale or other disposal of mineral materials, including...

Physicochemical characterization of mineral (iron/zinc) bound caseinate and their mineral uptake in Caco-2 cells.

PubMed

Shilpashree, B G; Arora, Sumit; Kapila, Suman; Sharma, Vivek

2018-08-15

Milk proteins (especially caseins) are widely accepted as good vehicle for the delivery of various bioactive compounds including minerals. Succinylation is one of the most acceptable chemical modification techniques to enhance the mineral binding ability of caseins. Addition of minerals to succinylated proteins may alter their physicochemical and biochemical properties. Physicochemical characteristics of succinylated sodium caseinate (S.NaCN)-mineral (iron/zinc) complexes were elucidated. Chromatographic behaviour and fluorescence intensity confirmed the structural modification of S.NaCN upon binding with minerals. The bound mineral from protein complexes showed significantly higher (P < 0.05) in vitro bioavailability (mineral uptake) than mineral salts in Caco-2 cells. Also, iron bound S.NaCN showed higher cellular ferritin formation than iron in its free form. These mineral bound protein complexes with improved bioavailability could safely replace inorganic fortificants in various functional food formulations. Copyright © 2018 Elsevier Ltd. All rights reserved.

Clay Mineral Crystal Structure Tied to Composition

NASA Image and Video Library

2016-12-13

This diagram illustrates how the dimensions of clay minerals' crystal structure are affected by which ions are present in the composition of the mineral. Different clay minerals were identified this way at two sites in Mars' Gale Crater: "Murray Buttes" and "Yellowknife Bay." In otherwise identical clay minerals, a composition that includes aluminum and ferric iron ions (red dots) results in slightly smaller crystalline unit cells than one that instead includes magnesium and ferrous iron ions (green dots). Ferric iron is more highly oxidized than ferrous iron. Crystalline cell units are the basic repeating building blocks that define minerals. X-ray diffraction analysis, a capability of the Chemistry and Mineralogy (CheMin) instrument on NASA's Curiosity Mars rover, identifies minerals from their crystalline structure. http://photojournal.jpl.nasa.gov/catalog/PIA21148

Developing a molecular picture of soil organic matter–mineral interactions by quantifying organo–mineral binding

DOE PAGES

Newcomb, C. J.; Qafoku, N. P.; Grate, J. W.; ...

2017-08-30

Long residence times of soil organic matter have been attributed to reactive mineral surface sites that sorb organic species and cause inaccessibility due to isolation and chemical stabilization at the organic-mineral interface. Instrumentation for probing this interface is limited. As a result, much of the micron- and molecular-scale knowledge about organic-mineral interactions remains largely qualitative. We report the use of force spectroscopy to directly measure the binding between organic ligands with known chemical functionalities to soil minerals in aqueous environments. By systematically studying the role of organic functional group chemistry with model minerals, we demonstrate that the chemistry of bothmore » the organic ligand and mineral contribute to values of binding free energy and that changes in pH and ionic strength produce significant differences in binding energies. These direct measurements of molecular binding provide mechanistic insights into organo-mineral interactions, which could potentially inform land-carbon models that explicitly include mineral-bound C pools.« less

Developing a molecular picture of soil organic matter–mineral interactions by quantifying organo–mineral binding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Newcomb, C. J.; Qafoku, N. P.; Grate, J. W.

Long residence times of soil organic matter have been attributed to reactive mineral surface sites that sorb organic species and cause inaccessibility due to isolation and chemical stabilization at the organic-mineral interface. Instrumentation for probing this interface is limited. As a result, much of the micron- and molecular-scale knowledge about organic-mineral interactions remains largely qualitative. We report the use of force spectroscopy to directly measure the binding between organic ligands with known chemical functionalities to soil minerals in aqueous environments. By systematically studying the role of organic functional group chemistry with model minerals, we demonstrate that the chemistry of bothmore » the organic ligand and mineral contribute to values of binding free energy and that changes in pH and ionic strength produce significant differences in binding energies. These direct measurements of molecular binding provide mechanistic insights into organo-mineral interactions, which could potentially inform land-carbon models that explicitly include mineral-bound C pools.« less

Report on "Methodologies for Investigating Microbial-Mineral Interactions: A Clay Minerals Society Short Course"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maurice, Patricia A.

2010-02-08

A workshop entitled, “Methods of Investigating Microbial-Mineral Interactions,” was held at the Clay Minerals Society meeting at the Pacific Northwest National Laboratory in Richland, WA on June 19, 2004. The workshop was organized by Patricia A. Maurice (University of Notre Dame) and Lesley A. Warren (McMaster University, CA). Speakers included: Dr. P. Bennett, Dr. J. Fredrickson (PNNL), Dr. S. Lower (Ohio State University), Dr. P. Maurice, Dr. S. Myneni (Princeton University), Dr. E. Shock (Arizona State), Dr. M. Tien (Penn State), Dr. L. Warren, and Dr. J. Zachara (PNNL). There were approximately 75 attendees at the workshop, including more thanmore » 20 students. A workshop volume was published by the Clay Minerals Society [Methods for Study of Microbe-Mineral Interactions (2006), CMS Workshop Lectures, vol 14(Patricia A. Maurice and Leslie A. Warren, eds.) ISBN 978-1-881208-15-0, 166 pp.]« less

Mineral facilities of Northern and Central Eurasia

USGS Publications Warehouse

Baker, Michael S.; Elias, Nurudeen; Guzman, Eric; Soto-Viruet, Yadira

2010-01-01

This map displays almost 900 records of mineral facilities within the countries that formerly constituted the Union of Soviet Socialist Republics (USSR). Each record represents one commodity and one facility type at a single geographic location. Facility types include mines, oil and gas fields, and plants, such as refineries, smelters, and mills. Common commodities of interest include aluminum, cement, coal, copper, gold, iron and steel, lead, nickel, petroleum, salt, silver, and zinc. Records include attributes, such as commodity, country, location, company name, facility type and capacity (if applicable), and latitude and longitude geographical coordinates (in both degrees-minutes-seconds and decimal degrees). The data shown on this map and in table 1 were compiled from multiple sources, including (1) the most recently available data from the U.S. Geological Survey (USGS) Minerals Yearbook (Europe and Central Eurasia volume), (2) mineral statistics and information from the USGS Minerals Information Web site (http://minerals.usgs.gov/minerals/pubs/country/europe.html), and (3) data collected by the USGS minerals information country specialists from sources, such as statistical publications of individual countries, annual reports and press releases of operating companies, and trade journals. Data reflect the most recent published table of industry structure for each country at the time of this publication. Additional information is available from the country specialists listed in table 2

Minerals Yearbook, volume II, Area Reports—Domestic

USGS Publications Warehouse

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume III, Area Reports—International

USGS Publications Warehouse

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Mineral Commodity Summaries 2008

USGS Publications Warehouse

,

2008-01-01

Each chapter of the 2008 edition of the U.S. Geological Survey (USGS) Mineral Commodity Summaries (MCS) includes information on events, trends, and issues for each mineral commodity as well as discussions and tabular presentations on domestic industry structure, Government programs, tariffs, 5-year salient statistics, and world production and resources. The MCS is the earliest comprehensive source of 2007 mineral production data for the world. More than 90 individual minerals and materials are covered by two-page synopses. National reserves and reserve base information for most mineral commodities found in this report, including those for the United States, are derived from a variety of sources. The ideal source of such information would be comprehensive evaluations that apply the same criteria to deposits in different geographic areas and report the results by country. In the absence of such evaluations, national reserves and reserve base estimates compiled by countries for selected mineral commodities are a primary source of national reserves and reserve base information. Lacking national assessment information by governments, sources such as academic articles, company reports, common business practice, presentations by company representatives, and trade journal articles, or a combination of these, serve as the basis for national reserves and reserve base information reported in the mineral commodity sections of this publication. A national estimate may be assembled from the following: historically reported reserves and reserve base information carried for years without alteration because no new information is available; historically reported reserves and reserve base reduced by the amount of historical production; and company reported reserves. International minerals availability studies conducted by the U.S. Bureau of Mines, before 1996, and estimates of identified resources by an international collaborative effort (the International Strategic Minerals

Microbe-Clay Mineral Reactions and Characterization Techniques

NASA Astrophysics Data System (ADS)

Dong, H.; Zhang, G.; Ji, S.; Jaisi, D.; Kim, J.

2008-12-01

Clays and clay minerals are ubiquitous in soils, sediments, and sedimentary rocks. They play an important role in environmental processes such as nutrient cycling, plant growth, contaminant migration, organic matter maturation, and petroleum production. The changes in the oxidation state of the structural iron in clay minerals, in part, control their physical and chemical properties in natural environments, such as clay particle flocculation, dispersion, swelling, hydraulic conductivity, surface area, cation and anion exchange capacity, and reactivity towards organic and inorganic contaminants. The structural ferric iron [Fe(III)] in clay minerals can be reduced either chemically or biologically. Many different chemical reductants have been tried, but the most commonly used agent is dithionite. Biological reductants are bacteria, including dissimilatory iron reducing prokaryotes (DIRP) and sulfate-reducing bacteria (SRB). A wide variety of DIRP have been used to reduce ferric iron in clay minerals, including mesophilic, thermophilic, and hyperthermophilic prokaryotes. Multiple clay minerals have been used for microbial reduction studies, including smectite, nontronite (iron-rich smectite variety), illite, illite/smectite, chlorite, and their various mixtures. All these clay minerals are reducible by microorganisms under various conditions with smectite (nontronite) being the most reducible. The reduction extent and rate of ferric iron in clay minerals are measured by wet chemistry, and the reduced clay mineral products are typically characterized with chemical methods, X-ray diffraction, scanning and transmission electron microscopy, Mössbauer spectroscopy, Fourier Transform Infrared Spectroscopy (FTIR), UV-vis spectroscopy, and synchrotron-based techniques (such as EXAFS). Microbially reduced smectites (nontronites) have been found to be reactive in reducing a variety of organic and inorganic contaminants. Degradable organic contaminants include pesticides

Relantionships between gold mineralization and granite - Discussion with the support of a pluridisciplinary study of the Passa Tres gold deposit (South Brazil)

NASA Astrophysics Data System (ADS)

Dressel, Bárbara; Chauvet, Alain; Trzaskos, Barbara; Biondi, Joao Carlos; Bruguier, Olivier; Monie, Patrick; Villanova, Sandro; Bazille, Jose

2016-04-01

The Passa Três Granite, located at East of the Paraná State is elongated following a NNE-SSW direction. This sienogranite is emplaced within metapelites of the meso to neoproterozoic Açungui Group, between the Morro Agudo and Lancinha transcurrent faults, comprising the N040°E trending Lancinha Transcurrent Fault System. Gold mineralization within the Passa Três Granite is constituted by huge quartz veins with sulfides, variable quantities of fluorite and carbonates, forming orebodies with different internal textures, including massive, banded, sheared and brecciated. Structural data indicate the existence of two major fault systems, one N-S and the other E-W, with dips of 15-45°W and 20-75°S, respectively. Both NS and EW systems are interpreted to be contemporaneous and conjugate. Normal motions are everywhere suspected and main mineralized veins are located at opening sites at these fault systems, such as pull-aparts. The structural model suggests that the normal motion can be initiated by shearing along a "guide" level, in which sulfides and clay minerals are concentrated. This configuration can be observed at several scales, such as field, hand samples and thin section. Mineralized veins mainly contain, in addition to the quartz of the gangue, sulphides (pyrite, chalcopyrite, galena, molybdenite), fluorite, chlorite, muscovite, sericite, and carbonate. The presence of sericite, kaolinite and chlorite indicate the occurrence of, at least, propylitic and phyllic-type alterations, both in core of the granite and best-expressed at the rim of quartz-rich orebodies. Gold occurs as native grains in core of the quartz veins, within fractures that affect pyrite and frequently exhibiting normal motions consistent with the one observed at larger scale and systematically associated with chalcopyrite and galena. Quartz veins are sometimes bordered by aplitic dike. Additionally, some of the veins can exhibit a very thin margin of adularia minerals that seems to

Some physicochemical aspects of water-soluble mineral flotation.

PubMed

Wu, Zhijian; Wang, Xuming; Liu, Haining; Zhang, Huifang; Miller, Jan D

2016-09-01

Some physicochemical aspects of water-soluble mineral flotation including hydration phenomena, associations and interactions between collectors, air bubbles, and water-soluble mineral particles are presented. Flotation carried out in saturated salt solutions, and a wide range of collector concentrations for effective flotation of different salts are two basic aspects of water-soluble mineral flotation. Hydration of salt ions, mineral particle surfaces, collector molecules or ions, and collector aggregates play an important role in water-soluble mineral flotation. The adsorption of collectors onto bubble surfaces is suggested to be the precondition for the association of mineral particles with bubbles. The association of collectors with water-soluble minerals is a complicated process, which may include the adsorption of collector molecules or ions onto such surfaces, and/or the attachment of collector precipitates or crystals onto the mineral surfaces. The interactions between the collectors and the minerals include electrostatic and hydrophobic interactions, hydrogen bonding, and specific interactions, with electrostatic and hydrophobic interactions being the common mechanisms. For the association of ionic collectors with minerals with an opposite charge, electrostatic and hydrophobic interactions could have a synergistic effect, with the hydrophobic interactions between the hydrophobic groups of the previously associated collectors and the hydrophobic groups of oncoming collectors being an important attractive force. Association between solid particles and air bubbles is the key to froth flotation, which is affected by hydrophobicity of the mineral particle surfaces, surface charges of mineral particles and bubbles, mineral particle size and shape, temperature, bubble size, etc. The use of a collector together with a frother and the use of mixed surfactants as collectors are suggested to improve flotation. Copyright © 2016 Elsevier B.V. All rights reserved.

Mineral Processing Sector

EPA Pesticide Factsheets

Find environmental regulatory and compliance information for the nonmetallic mineral processing sector (NAICS 327), including NESHAPs for asbestos and hazardous waste, and wastewater permit information.

Hydrothermal Evolution of the Giant Cenozoic Kadjaran porphyry Cu-Mo deposit, Tethyan metallogenic belt, Armenia, Lesser Caucasus: mineral paragenetic, cathodoluminescence and fluid inclusion constraints

NASA Astrophysics Data System (ADS)

Hovakimyan, Samvel; Moritz, Robert; Tayan, Rodrik; Rezeau, Hervé

2016-04-01

The Lesser Caucasus belongs to the Central segment of the Tethyan metallogenic belt and it is a key area to understand the metallogenic evolution between the Western & Central parts of the Tethyan belt and its extension into Iran. Zangezur is the most important mineral district in the southernmost Lesser Caucasus. It is a component of the South Armenian block, and it was generated during the convergence and collision of the southern margin of the Eurasian plate and the northern margin of the Arabian plate, and terranes of Gondwana origin (Moritz et al., in press). The Zangezur ore district consists of the Tertiary Meghri-Ordubad composite pluton, which is characterized by a long-lasting Eocene to Pliocene magmatic, tectonic and metallogenic evolution. It hosts major porphyries Cu-Mo and epithermal Au - polymetallic deposits and occurrences, including the giant world class Kadjaran porphyry Cu-Mo deposit (2244 Mt reserves, 0.3% Cu, 0.05% Mo and 0.02 g/t Au). The Kadjaran deposit is hosted by a monzonite intrusion (31.83±0.02Ma; Moritz et al., in press). Detailed field studies of the porphyry stockwork and veins of the different mineralization stages, their crosscutting and displacement relationships and the age relationship between different paragenetic mineral associations were the criteria for distinction of the main stages of porphyry mineralization at the Kadjaran deposit. The economic stages being: quartz- molybdenite, quartz-molybdenite-chalcopyrite, and quartz-chalcopyrite. The main paragenetic association of the Kadjaran porphyry deposit includes pyrite, molybdenite, chalcopyrite, bornite, chalcocite, pyrrhotite, covellite, sphalerite, and galena. Recent field observations in the Kadjaran open pit revealed the presence of epithermal veins with late vuggy silica and advanced argillic alteration in the north-eastern and eastern parts of the deposit. They are distributed as separate veins and have also been recognized in re-opened porphyry veins and in

43 CFR 19.8 - Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

Code of Federal Regulations, 2010 CFR

2010-10-01

... patents, and mineral leasing within National Forest Wilderness. 19.8 Section 19.8 Public Lands: Interior... § 19.8 Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest... locations, mineral patents, and mineral leasing within National Forest Wilderness are contained in parts...

43 CFR 19.8 - Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 1 2014-10-01 2014-10-01 false Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest Wilderness. 19.8 Section 19.8 Public Lands: Interior... § 19.8 Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

43 CFR 19.8 - Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 1 2011-10-01 2011-10-01 false Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest Wilderness. 19.8 Section 19.8 Public Lands: Interior... § 19.8 Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

43 CFR 19.8 - Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 1 2012-10-01 2011-10-01 true Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest Wilderness. 19.8 Section 19.8 Public Lands: Interior... § 19.8 Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

43 CFR 19.8 - Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 1 2013-10-01 2013-10-01 false Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest Wilderness. 19.8 Section 19.8 Public Lands: Interior... § 19.8 Prospecting, mineral locations, mineral patents, and mineral leasing within National Forest...

30 CFR 48.26 - Experienced miner training.

Code of Federal Regulations, 2010 CFR

2010-07-01

... TRAINING AND RETRAINING OF MINERS Training and Retraining of Miners Working at Surface Mines and Surface... must include the following instruction: (1) Introduction to work environment. The course shall include... firewarning signals and firefighting procedures in effect at the mine. (6) Ground controls; working in areas...

U-Pb isotope systematics and age of uranium mineralization, Midnite mine, Washington.

USGS Publications Warehouse

Ludwig, K. R.; Nash, J.T.; Naeser, C.W.

1981-01-01

Uranium ores at the Midnite mine, near Spokane, Washington, occur in phyllites and calcsilicates of the Proterozoic Togo Formation, near the margins of an anomalously uraniferous, porphyritic quartz monzonite of Late Cretaceous age. The present geometry of the ore zones is tabular, with the thickest zones above depressions in the pluton-country rock contact. Analyses of high-grade ores from the mine define a 207 Pb/ 204 Pb- 235 U/ 204 Pb isochron indicating an age of mineralization of 51.0 + or - 0.5 m.y. This age coincides with a time of regional volcanic activity (Sanpoil Volcanics), shallow intrusive activity, erosion, and faulting. U-Th-Pb isotopic ages of zircons from the porphyritic quartz monzonite in the mine indicate an age of about 75 m.y., hence the present orebodies were formed about 24 m.y. after its intrusion. The 51-m.y. time of mineralization probably represents a period of mobilization and redeposition of uranium by supergene ground waters, perhaps aided by mild heating and ground preparation and preserved by a capping of newly accumulated, impermeable volcanic rocks. It seems most likely that the initial concentration of uranium occurred about 75 m.y. ago, probably from relatively mild hydrothermal fluids in the contact-metamorphic aureole of the U-rich porphyritic quartz monzonite.Pitchblende, coffinitc, pyrite, marcasite, and hisingerite are the most common minerals in the uranium-bearing veinlets, with minor sphalerite and chalcopyrite. Coffinitc with associated marcasite is paragenetically later than pitchblende, though textural and isotopic evidence suggests no large difference in the times of pitchblende and colfinite formation.The U-Pb isotope systematics of total ores and of pitchblende-coffinite and pyrite-marcasite separates show that whereas open system behavior for U and Pb is essentially negligible for large (200-500 g) ore samples, Pb migration has occurred on a scale of 1 to 10 mm (out of pitchblende and coffinite and into pyrite

30 CFR 250.211 - What must the EP include?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What must the EP include? 250.211 Section 250.211 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT OF... Information Contents of Exploration Plans (ep) § 250.211 What must the EP include? Your EP must include the...

Mineral resource of the month: Mica

USGS Publications Warehouse

Willett, Jason C.

2014-01-01

The mica mineral group includes 34 phyllosilicate minerals, all with a layered, platy texture. The mineral has been known for millennia: Mica was first mined in India about 4,000 years ago, where it was used primarily in medicines. The Mayans used it for decorative effect in stucco to make their temples sparkle in the sun. Today it is used in everything from electrical products to makeup.

Surface contamination artificially elevates initial sweat mineral concentrations

USDA-ARS?s Scientific Manuscript database

During exercise in the heat, sweat is initially concentrated in minerals, but serial sweat samples appear more dilute. Possible causes include reduced dermal mineral concentrations or flushing of surface contamination. PURPOSE: To simultaneously sample mineral concentrations in transdermal fluid (T...

The life cycle of a mineral deposit: a teacher's guide for hands-on mineral education activities

USGS Publications Warehouse

Frank, Dave; Galloway, John; Assmus, Ken

2005-01-01

This teacher's guide defines what a mineral deposit is and how a mineral deposit is identified and measured, how the mineral resources are extracted, and how the mining site is reclaimed; how minerals and mineral resources are processed; and how we use mineral resources in our every day lives. Included are 10 activitybased learning exercises that educate students on basic geologic concepts; the processes of finding, identifying, and extracting the resources from a mineral deposit; and the uses of minerals. The guide is intended for K through 12 Earth science teachers and students and is designed to meet the National Science Content Standards as defined by the National Research Council (1996). To assist in the understanding of some of the geology and mineral terms, see the Glossary (appendix 1) and Minerals and Their Uses (appendix 2). The process of finding or exploring for a mineral deposit, extracting or mining the resource, recovering the resource, also known as beneficiation, and reclaiming the land mined can be described as the “life cycle” of a mineral deposit. The complete process is time consuming and expensive, requiring the use of modern technology and equipment, and may take many years to complete. Sometimes one entity or company completes the entire process from discovery to reclamation, but often it requires multiple groups with specialized experience working together. Mineral deposits are the source of many important commodities, such as copper and gold, used by our society, but it is important to realize that mineral deposits are a nonrenewable resource. Once mined, they are exhausted, and another source must be found. New mineral deposits are being continuously created by the Earth but may take millions of years to form. Mineral deposits differ from renewable resources, such as agricultural and timber products, which may be replenished within a few months to several years.

The "chessboard" classification scheme of mineral deposits: Mineralogy and geology from aluminum to zirconium

NASA Astrophysics Data System (ADS)

Dill, Harald G.

2010-06-01

Economic geology is a mixtum compositum of all geoscientific disciplines focused on one goal, finding new mineral depsosits and enhancing their exploitation. The keystones of this mixtum compositum are geology and mineralogy whose studies are centered around the emplacement of the ore body and the development of its minerals and rocks. In the present study, mineralogy and geology act as x- and y-coordinates of a classification chart of mineral resources called the "chessboard" (or "spreadsheet") classification scheme. Magmatic and sedimentary lithologies together with tectonic structures (1 -D/pipes, 2 -D/veins) are plotted along the x-axis in the header of the spreadsheet diagram representing the columns in this chart diagram. 63 commodity groups, encompassing minerals and elements are plotted along the y-axis, forming the lines of the spreadsheet. These commodities are subjected to a tripartite subdivision into ore minerals, industrial minerals/rocks and gemstones/ornamental stones. Further information on the various types of mineral deposits, as to the major ore and gangue minerals, the current models and the mode of formation or when and in which geodynamic setting these deposits mainly formed throughout the geological past may be obtained from the text by simply using the code of each deposit in the chart. This code can be created by combining the commodity (lines) shown by numbers plus lower caps with the host rocks or structure (columns) given by capital letters. Each commodity has a small preface on the mineralogy and chemistry and ends up with an outlook into its final use and the supply situation of the raw material on a global basis, which may be updated by the user through a direct link to databases available on the internet. In this case the study has been linked to the commodity database of the US Geological Survey. The internal subdivision of each commodity section corresponds to the common host rock lithologies (magmatic, sedimentary, and

Adsorption of Aqueous Crude Oil Components on the Basal Surfaces of Clay Minerals: Molecular Simulations Including Salinity and Temperature Effects

DOE PAGES

Greathouse, J. A.; Cygan, R. T.; Fredrich, J. T.; ...

2017-09-28

Molecular simulations of the adsorption of representative organic molecules onto the basal surfaces of various clay minerals were used to assess the mechanisms of enhanced oil recovery associated with salinity changes and water flooding. Simulations at the density functional theory (DFT) and classical levels provide insights into the molecular structure, binding energy, and interfacial behavior of saturate, aromatic, and resin molecules near clay mineral surfaces. Periodic DFT calculations reveal binding geometries and ion pairing mechanisms at mineral surfaces while also providing a basis for validating the classical force field approach. Through classical molecular dynamics simulations, the influence of aqueous cationsmore » at the interface and the role of water solvation are examined to better evaluate the dynamical nature of cation-organic complexes and their co-adsorption onto the clay surfaces. The extent of adsorption is controlled by the hydrophilic nature and layer charge of the clay mineral. All organic species studied showed preferential adsorption on hydrophobic mineral surfaces. However, the anionic form of the resin (decahydro-2-naphthoic acid)—expected to be prevalent at near-neutral pH conditions in petroleum reservoirs—readily adsorbs to the hydrophilic kaolinite surface through a combination of cation pairing and hydrogen bonding with surface hydroxyl groups. Analysis of cation-organic pairing in both the adsorbed and desorbed states reveals a strong preference for organic anions to coordinate with divalent calcium ions rather than monovalent sodium ions, lending support to current theories regarding low-salinity water flooding.« less

Adsorption of Aqueous Crude Oil Components on the Basal Surfaces of Clay Minerals: Molecular Simulations Including Salinity and Temperature Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greathouse, J. A.; Cygan, R. T.; Fredrich, J. T.

Molecular simulations of the adsorption of representative organic molecules onto the basal surfaces of various clay minerals were used to assess the mechanisms of enhanced oil recovery associated with salinity changes and water flooding. Simulations at the density functional theory (DFT) and classical levels provide insights into the molecular structure, binding energy, and interfacial behavior of saturate, aromatic, and resin molecules near clay mineral surfaces. Periodic DFT calculations reveal binding geometries and ion pairing mechanisms at mineral surfaces while also providing a basis for validating the classical force field approach. Through classical molecular dynamics simulations, the influence of aqueous cationsmore » at the interface and the role of water solvation are examined to better evaluate the dynamical nature of cation-organic complexes and their co-adsorption onto the clay surfaces. The extent of adsorption is controlled by the hydrophilic nature and layer charge of the clay mineral. All organic species studied showed preferential adsorption on hydrophobic mineral surfaces. However, the anionic form of the resin (decahydro-2-naphthoic acid)—expected to be prevalent at near-neutral pH conditions in petroleum reservoirs—readily adsorbs to the hydrophilic kaolinite surface through a combination of cation pairing and hydrogen bonding with surface hydroxyl groups. Analysis of cation-organic pairing in both the adsorbed and desorbed states reveals a strong preference for organic anions to coordinate with divalent calcium ions rather than monovalent sodium ions, lending support to current theories regarding low-salinity water flooding.« less

Alaska Geochemical Database, Version 2.0 (AGDB2)--including “best value” data compilations for rock, sediment, soil, mineral, and concentrate sample media

USGS Publications Warehouse

Granitto, Matthew; Schmidt, Jeanine M.; Shew, Nora B.; Gamble, Bruce M.; Labay, Keith A.

2013-01-01

The Alaska Geochemical Database Version 2.0 (AGDB2) contains new geochemical data compilations in which each geologic material sample has one “best value” determination for each analyzed species, greatly improving speed and efficiency of use. Like the Alaska Geochemical Database (AGDB, http://pubs.usgs.gov/ds/637/) before it, the AGDB2 was created and designed to compile and integrate geochemical data from Alaska in order to facilitate geologic mapping, petrologic studies, mineral resource assessments, definition of geochemical baseline values and statistics, environmental impact assessments, and studies in medical geology. This relational database, created from the Alaska Geochemical Database (AGDB) that was released in 2011, serves as a data archive in support of present and future Alaskan geologic and geochemical projects, and contains data tables in several different formats describing historical and new quantitative and qualitative geochemical analyses. The analytical results were determined by 85 laboratory and field analytical methods on 264,095 rock, sediment, soil, mineral and heavy-mineral concentrate samples. Most samples were collected by U.S. Geological Survey personnel and analyzed in U.S. Geological Survey laboratories or, under contracts, in commercial analytical laboratories. These data represent analyses of samples collected as part of various U.S. Geological Survey programs and projects from 1962 through 2009. In addition, mineralogical data from 18,138 nonmagnetic heavy-mineral concentrate samples are included in this database. The AGDB2 includes historical geochemical data originally archived in the U.S. Geological Survey Rock Analysis Storage System (RASS) database, used from the mid-1960s through the late 1980s and the U.S. Geological Survey PLUTO database used from the mid-1970s through the mid-1990s. All of these data are currently maintained in the National Geochemical Database (NGDB). Retrievals from the NGDB were used to generate

30 CFR 285.645 - What must I include in my GAP?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must I include in my GAP? 285.645 Section 285.645 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE RENEWABLE... Requirements Contents of the General Activities Plan § 285.645 What must I include in my GAP? (a) You must...

30 CFR 285.610 - What must I include in my SAP?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must I include in my SAP? 285.610 Section 285.610 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE RENEWABLE... Requirements Contents of the Site Assessment Plan § 285.610 What must I include in my SAP? Your SAP must...

Mesozoic Magmatism and Base-Metal Mineralization in the Fortymile Mining District, Eastern Alaska - Initial Results of Petrographic, Geochemical, and Isotopic Studies in the Mount Veta Area

USGS Publications Warehouse

Dusel-Bacon, Cynthia; Slack, John F.; Aleinikoff, John N.; Mortensen, James K.

2009-01-01

We present here the initial results of a petrographic, geochemical, and isotopic study of Mesozoic intrusive rocks and spatially associated Zn-Pb-Ag-Cu-Au prospects in the Fortymile mining district in the southern Eagle quadrangle, Alaska. Analyzed samples include mineralized and unmineralized drill core from 2006 and 2007 exploration by Full Metal Minerals, USA, Inc., at the Little Whiteman (LWM) and Fish prospects, and other mineralized and plutonic samples collected within the mining district is part of the USGS study. Three new ion microprobe U-Pb zircon ages are: 210 +- 3 Ma for quartz diorite from LWM, 187 +- 3 Ma for quartz monzonite from Fish, and 70.5 +- 1.1 Ma for altered rhyolite porphyry from Fish. We also present 11 published and unpublished Mesozoic thermal ionization mass spectrometric U-Pb zircon and titanite ages and whole-rock geochemical data for the Mesozoic plutonic rocks. Late Triassic and Early Jurassic plutons generally have intermediate compositions and are slightly foliated, consistent with synkinematic intrusion. Several Early Jurassic plutons contain magmatic epidote, indicating emplacement of the host plutons at mesozonal crustal depths of greater than 15 km. Trace-element geochemical data indicate an arc origin for the granitoids, with an increase in the crustal component with time. Preliminary study of drill core from the LWM Zn-Pb-Cu-Ag prospect supports a carbonate-replacement model of mineralization. LWM massive sulfides consist of sphalerite, galena, and minor pyrite and chalcopyrite, in a gangue of calcite and lesser quartz; silver resides in Sb-As-Ag sulfosalts and pyrargyrite, and probably in submicroscopic inclusions within galena. Whole-rock analyses of LWM drill cores also show elevated In, an important metal in high-technology products. Hypogene mineralized rocks at Fish, below the secondary Zn-rich zone, are associated with a carbonate host and also may be of replacement origin, or alternatively, may be a magnetite

Petro-mineralogical Studies of the Paleoproterozoic Phosphorites in the Sonrai basin, Lalitpur District, Uttar Pradesh, India

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dar, Shamim A., E-mail: sjshamim@gmail.com; Khan, K. F.; Khan, Saif A.

2015-09-15

The Paleoproterozoic phosphorites constitute an economically significant component of the Sonrai basin of Lalitpur district. These are associated with ferruginous shale, ironstone, limestone and quartz breccia. Petro-mineralogical studies of samples of the phosphorites, using X-ray diffractometry and scanning electron microscopy, reveal that the collophane (carbonate-fluorapatite) is the dominant phosphate mineral. Calcite, dolomite, quartz, mica and haematite are the dominant gangue constituents. The phosphate minerals occur as oolites mutually replaced by carbonate and silica. The presence of iron oxides has been found in most of the thin sections. There is meagre evidence of organic matter in the form of filaments ofmore » microbial phosphate laminae in the samples of phosphorite. The mineral assemblages, their texture and various forms in these phosphorites may be due to some environmental vicissitudes followed by replacement processes and biogenic activities.« less

Worldwide Directory of Mineral Industries Education and Research.

ERIC Educational Resources Information Center

Wohlbier, Herbert; And Others

Presented is background knowlege of the institutions of the world involved in mineral industry education and research, including detailed information on the professional staff, research activities, and capabilities of the various mineral industry departments of these institutions. Also included is information on special interest within a…

36 CFR 293.14 - Mineral leases and mineral permits.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 2 2011-07-01 2011-07-01 false Mineral leases and mineral... AGRICULTURE WILDERNESS-PRIMITIVE AREAS § 293.14 Mineral leases and mineral permits. (a) All laws pertaining to mineral leasing shall extend to each National Forest Wilderness for the period specified in the Wilderness...

36 CFR 293.14 - Mineral leases and mineral permits.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Mineral leases and mineral... AGRICULTURE WILDERNESS-PRIMITIVE AREAS § 293.14 Mineral leases and mineral permits. (a) All laws pertaining to mineral leasing shall extend to each National Forest Wilderness for the period specified in the Wilderness...

36 CFR 293.14 - Mineral leases and mineral permits.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 2 2012-07-01 2012-07-01 false Mineral leases and mineral... AGRICULTURE WILDERNESS-PRIMITIVE AREAS § 293.14 Mineral leases and mineral permits. (a) All laws pertaining to mineral leasing shall extend to each National Forest Wilderness for the period specified in the Wilderness...

36 CFR 293.14 - Mineral leases and mineral permits.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 2 2014-07-01 2014-07-01 false Mineral leases and mineral... AGRICULTURE WILDERNESS-PRIMITIVE AREAS § 293.14 Mineral leases and mineral permits. (a) All laws pertaining to mineral leasing shall extend to each National Forest Wilderness for the period specified in the Wilderness...

36 CFR 293.14 - Mineral leases and mineral permits.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 2 2013-07-01 2013-07-01 false Mineral leases and mineral... AGRICULTURE WILDERNESS-PRIMITIVE AREAS § 293.14 Mineral leases and mineral permits. (a) All laws pertaining to mineral leasing shall extend to each National Forest Wilderness for the period specified in the Wilderness...

30 CFR 285.906 - What must my decommissioning application include?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must my decommissioning application include? 285.906 Section 285.906 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE RENEWABLE ENERGY ALTERNATE USES OF EXISTING FACILITIES ON THE OUTER CONTINENTAL SHELF...

Mineral deposit densities for estimating mineral resources

USGS Publications Warehouse

Singer, Donald A.

2008-01-01

Estimates of numbers of mineral deposits are fundamental to assessing undiscovered mineral resources. Just as frequencies of grades and tonnages of well-explored deposits can be used to represent the grades and tonnages of undiscovered deposits, the density of deposits (deposits/area) in well-explored control areas can serve to represent the number of deposits. Empirical evidence presented here indicates that the processes affecting the number and quantity of resources in geological settings are very general across many types of mineral deposits. For podiform chromite, porphyry copper, and volcanogenic massive sulfide deposit types, the size of tract that geologically could contain the deposits is an excellent predictor of the total number of deposits. The number of mineral deposits is also proportional to the type’s size. The total amount of mineralized rock is also proportional to size of the permissive area and the median deposit type’s size. Regressions using these variables provide a means to estimate the density of deposits and the total amount of mineralization. These powerful estimators are based on analysis of ten different types of mineral deposits (Climax Mo, Cuban Mn, Cyprus massive sulfide, Franciscan Mn, kuroko massive sulfide, low-sulfide quartz-Au vein, placer Au, podiform Cr, porphyry Cu, and W vein) from 108 permissive control tracts around the world therefore generalizing across deposit types. Despite the diverse and complex geological settings of deposit types studied here, the relationships observed indicate universal controls on the accumulation and preservation of mineral resources that operate across all scales. The strength of the relationships (R 2=0.91 for density and 0.95 for mineralized rock) argues for their broad use. Deposit densities can now be used to provide a guideline for expert judgment or used directly for estimating the number of most kinds of mineral deposits.

A world of minerals in your mobile device

USGS Publications Warehouse

Jenness, Jane E.; Ober, Joyce A.; Wilkins, Aleeza M.; Gambogi, Joseph

2016-09-15

Mobile phones and other high-technology communications devices could not exist without mineral commodities. More than one-half of all components in a mobile device—including its electronics, display, battery, speakers, and more—are made from mined and semiprocessed materials (mineral commodities). Some mineral commodities can be recovered as byproducts during the production and processing of other commodities. As an example, bauxite is mined for its aluminum content, but gallium is recovered during the aluminum production process. The images show the ore minerals (sources) of some mineral commodities that are used to make components of a mobile device. On the reverse side, the map and table depict the major source countries producing these mineral commodities along with how these commodities are used in mobile devices. For more information on minerals, visit http://minerals.usgs.gov.

Phosphorus K-edge XANES spectroscopy of mineral standards

PubMed Central

Ingall, Ellery D.; Brandes, Jay A.; Diaz, Julia M.; de Jonge, Martin D.; Paterson, David; McNulty, Ian; Elliott, W. Crawford; Northrup, Paul

2011-01-01

Phosphorus K-edge X-ray absorption near-edge structure (XANES) spectroscopy was performed on phosphate mineral specimens including (a) twelve specimens from the apatite group covering a range of compositional variation and crystallinity; (b) six non-apatite calcium-rich phosphate minerals; (c) 15 aluminium-rich phosphate minerals; (d) ten phosphate minerals rich in either reduced iron or manganese; (e) four phosphate minerals rich in either oxidized iron or manganese; (f) eight phosphate minerals rich in either magnesium, copper, lead, zinc or rare-earth elements; and (g) four uranium phosphate minerals. The identity of all minerals examined in this study was independently confirmed using X-ray powder diffraction. Minerals were distinguished using XANES spectra with a combination of pre-edge features, edge position, peak shapes and post-edge features. Shared spectral features were observed in minerals with compositions dominated by the same specific cation. Analyses of apatite-group minerals indicate that XANES spectral patterns are not strongly affected by variations in composition and crystallinity typical of natural mineral specimens. PMID:21335905

Mineral concentrations in diets, water, and milk and their value in estimating on-farm excretion of manure minerals in lactating dairy cows.

PubMed

Castillo, A R; St-Pierre, N R; Silva del Rio, N; Weiss, W P

2013-05-01

Thirty-nine commercial dairies in Merced County, California were enrolled in the present study to (1) compare lactating cow mineral intakes (via drinking water and total mixed ration) to the National Research Council (NRC) requirements, (2) evaluate the association between dietary concentrations of minerals with and without drinking water and adjusted for mineral concentrations in milk, and (3) compare 4 different methods to estimate excretion of minerals using either assays or estimations of milk mineral outputs and total daily mineral intake per cow with or without minerals coming from drinking water. Dairies were selected to represent a range of herd milk yields and a range of water mineral contents. Samples of total mixed ration, drinking water, and bulk tank milk were taken on 2 different days, 3 to 7d apart in each farm. Across-farm medians and percentile distributions were used to analyze results. The herd median milk yield interquartile ranged (10th to 90th percentile) from less than 25 to more than 39 kg/d and the concentration of total solids in water interquartile ranged from less than 200 to more than 1,490 mg/L. Including drinking water minerals in the diets increased dietary concentrations by <4% for all minerals except for Na and Cl, which increased by 9.3 and 6.5%, respectively. Concentrations of P and K in milk were essentially the same as the NRC value to estimate lactation requirements. However, NRC milk values of Ca, Cl, and Zn were 10 to 20% greater than dairy farm values; and Na, Cu, Fe, and Mn were no less than 36% below NRC values. Estimated excretion of minerals via manure varied substantially across farms. Farms in the 10th percentile did have 2 to 3 times less estimated mineral excretions than those in the 90th percentile (depending on the mineral). Although including water minerals increased excretion of most minerals, the actual median effect of Ca, Mg, S, Cu, Fe, and Mn was less than 5%, and about 8% for Na and Cl. Replacing assayed

Oxalate minerals on Mars?

NASA Astrophysics Data System (ADS)

Applin, D. M.; Izawa, M. R. M.; Cloutis, E. A.; Goltz, D.; Johnson, J. R.

2015-06-01

Small amounts of unidentified organic compounds have only recently been inferred on Mars despite strong reasons to expect significant concentrations and decades of searching. Based on X-ray diffraction and reflectance spectroscopic analyses we show that solid oxalic acid and its most common mineral salts are stable under the pressure and ultraviolet irradiation environment of the surface of Mars, and could represent a heretofore largely overlooked reservoir of organic carbon in the martian near-surface. In addition to the delivery to Mars by carbonaceous chondrites, oxalate minerals are among the predicted breakdown products of meteoritic organic matter delivered to the martian surface, as well as any endogenic organic carbon reaching the martian surface from the interior. A reinterpretation of pyrolysis experiments from the Viking, Phoenix, and Mars Science Laboratory missions shows that all are consistent with the presence of significant concentrations of oxalate minerals. Oxalate minerals could be important in numerous martian geochemical processes, including acting as a possible nitrogen sink (as ammonium oxalate), and contributing to the formation of “organic” carbonates, methane, and hydroxyl radicals.

Skeletal biology: Where matrix meets mineral

PubMed Central

Young, Marian F.

2017-01-01

The skeleton is unique from all other tissues in the body because of its ability to mineralize. The incorporation of mineral into bones and teeth is essential to give them strength and structure for body support and function. For years, researchers have wondered how mineralized tissues form and repair. A major focus in this context has been on the role of the extracellular matrix, which harbors key regulators of the mineralization process. In this introductory minireview, we will review some key concepts of matrix biology as it related to mineralized tissues. Concurrently, we will highlight the subject of this special issue covering many aspects of mineralized tissues, including bones and teeth and their associated structures cartilage and tendon. Areas of emphasis are on the generation and analysis of new animal models with permutations of matrix components as well as the development of new approaches for tissue engineering for repair of damaged hard tissue. In assembling key topics on mineralized tissues written by leaders in our field, we hope the reader will get a broad view of the topic and all of its fascinating complexities. PMID:27131884

The mineral economy of Brazil--Economia mineral do Brasil

USGS Publications Warehouse

Gurmendi, Alfredo C.; Barboza, Frederico Lopes; Thorman, Charles H.

1999-01-01

This study depicts the Brazilian government structure, mineral legislation and investment policy, taxation, foreign investment policies, environmental laws and regulations, and conditions in which the mineral industry operates. The report underlines Brazil's large and diversified mineral endowment. A total of 37 mineral commodities, or groups of closely related commodities, is discussed. An overview of the geologic setting of the major mineral deposits is presented. This report is presented in English and Portuguese in pdf format.

43 CFR 3583.3 - Applications for hardrock mineral leases.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Applications for hardrock mineral leases... LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and... hardrock mineral leases. No specific form is required. An application shall include the applicant's name...

43 CFR 3583.3 - Applications for hardrock mineral leases.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Applications for hardrock mineral leases... LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and... hardrock mineral leases. No specific form is required. An application shall include the applicant's name...

43 CFR 3583.3 - Applications for hardrock mineral leases.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Applications for hardrock mineral leases... LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and... hardrock mineral leases. No specific form is required. An application shall include the applicant's name...

43 CFR 3583.3 - Applications for hardrock mineral leases.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Applications for hardrock mineral leases... LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SPECIAL LEASING AREAS Shasta and... hardrock mineral leases. No specific form is required. An application shall include the applicant's name...

High-pressure minerals in shocked meteorites

NASA Astrophysics Data System (ADS)

Tomioka, Naotaka; Miyahara, Masaaki

2017-09-01

Heavily shocked meteorites contain various types of high-pressure polymorphs of major minerals (olivine, pyroxene, feldspar, and quartz) and accessory minerals (chromite and Ca phosphate). These high-pressure minerals are micron to submicron sized and occur within and in the vicinity of shock-induced melt veins and melt pockets in chondrites and lunar, howardite-eucrite-diogenite (HED), and Martian meteorites. Their occurrence suggests two types of formation mechanisms (1) solid-state high-pressure transformation of the host-rock minerals into monomineralic polycrystalline aggregates, and (2) crystallization of chondritic or monomineralic melts under high pressure. Based on experimentally determined phase relations, their formation pressures are limited to the pressure range up to 25 GPa. Textural, crystallographic, and chemical characteristics of high-pressure minerals provide clues about the impact events of meteorite parent bodies, including their size and mutual collision velocities and about the mineralogy of deep planetary interiors. The aim of this article is to review and summarize the findings on natural high-pressure minerals in shocked meteorites that have been reported over the past 50 years.

Mineralogy, textures, and relative age relationships of massive sulfide ore in the West Shasta district, California ( USA).

USGS Publications Warehouse

Howe, S.S.

1985-01-01

The Devonian massive sulfide orebodies of the West Shasta district in N California are composed primarily of pyrite, with lesser amounts of other sulfide and gangue minerals. Examination of polished thin sections of more than 100 samples from the Mammoth, Shasta King, Early Bird, Balaklala, Keystone, and Iron Mountain mines suggests that mineralization may be divided into 6 paragenetic stages, the last 5 each separated by an episode of deformation: 1) precipitation of fine-grained, locally colloform and framboidal pyrite and sphalerite; 2) deposition of fine-grained arsenopyrite and coarse-grained pyrite; 3) penetration and local replacement of sulfide minerals of stages 1 and 2 along growth zones and fractures by chalcopyrite, sphalerite, galena, tennantite, pyrrhotite, bornite, and idaite; 4) recrystallization and remobilization of existing minerals; 5) deposition of quartz, white mica, chlorite, and calcite; and 6) formation of bornite, digenite, chalcocite, and covellite during supergene enrichment of several orebodies at the Iron Mountain mine. Mineralogic and textural evidence do not support a second major episode of massive sulfide mineralization during the Permian. -from Author

30 CFR 48.6 - Experienced miner training.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (b) Experienced miners must complete the training prescribed in this section before beginning work... to work environment. The course shall include a visit and tour of the mine. The methods of mining... responsibilities of such supervisors and miners' representatives; and an introduction to the operator's rules and...

Mineral-resource data bases

USGS Publications Warehouse

,

1997-01-01

Data bases are essential for modern scientific research. The new and exciting work being done in the Mineral Resource Program in the U.S. Geological Survey (USGS) usually begins with the question, "Where are the known deposits?" A mineral-resource data base containing this type of information and more can be useful not just to USGS scientists, but to anyone who needs such data. Users of the data bases from outside the USGS include mining and exploration companies, environmental groups, academia, other Federal Agencies, and the general public. At present, the USGS has two large mineral-resource data bases, MRDS (Mineral Resource Data System) and MAS (Minerals Availability System). MRDS was built and is mamtained by the USGS, and MAS was built and maintained by the Bureau of Mines. In 1996, after the Bureau was abolished, MAS was transferred to the USGS. The two data bases were compiled for different purposes and contain very different mformation. For instance, MAS contains information on costs, details of mining methods, and feasibility studies. MRDS has mineralogical and geologic data that are not contained in MAS. Because they are both mineral-resource data bases, however, they contain some information in common, such as location, name(s) of sites, and commodities present. Both data bases are international in scope, and both are quite large. MRDS contains over 110,000 records, while MAS has over 220,000. One reason that MAS has more records is that it contains information on smelters, mill sites, and fossil fuel sites, as well as mineral- resource sites. The USGS is working to combine the information in both data bases. This is a large undertaking that will require some years to complete. In the interim, information from both data bases will still be available

30 CFR 285.701 - What must I include in my Facility Design Report?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must I include in my Facility Design Report? 285.701 Section 285.701 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR... Design, Fabrication, and Installation Reports § 285.701 What must I include in my Facility Design Report...

Destabilization of emulsions by natural minerals.

PubMed

Yuan, Songhu; Tong, Man; Wu, Gaoming

2011-09-15

This study developed a novel method to destabilize emulsions and recycle oils, particularly for emulsified wastewater treatment. Natural minerals were used as demulsifying agents, two kinds of emulsions collected from medical and steel industry were treated. The addition of natural minerals, including artificial zeolite, natural zeolite, diatomite, bentonite and natural soil, could effectively destabilize both emulsions at pH 1 and 60 °C. Over 90% of chemical oxygen demand (COD) can be removed after treatment. Medical emulsion can be even destabilized by artificial zeolite at ambient temperature. The mechanism for emulsion destabilization by minerals was suggested as the decreased electrostatic repulsion at low pH, the enhanced gathering of oil microdroplets at elevated temperature, and the further decreased surface potential by the addition of minerals. Both flocculation and coalescence were enhanced by the addition of minerals at low pH and elevated temperature. Copyright © 2011 Elsevier B.V. All rights reserved.

Fractionation of mineral species by electrophoresis

NASA Technical Reports Server (NTRS)

Dunning, J. D.; Herren, B. J.; Tipps, R. W.; Snyder, R. S.

1982-01-01

The fractionation of fine-grained aggregates into their major components is a problem in many scientific areas including earth and planetary science. Electrophoresis, the transport of electrically charged particles, immersed in a suspension medium, by a direct current field (Bier, 1959), was employed in this study as a means of separating simulated lunar soil into its constituent minerals. In these tests, conducted in a static analytical cylindrical microelectrophoresis apparatus, samples of simulated lunar soil and samples of pure mineral constituents were placed in the chamber; the electrophoretic mobilities of the lunar soil and the individual mineral constituents were measured. In most of the suspension buffers employed separability was indicated, on the basis of differences in mobility, for all the constituent mineral species except ilmenite and pyroxene, which were not efficiently separable in any of the buffers. Although only a few suspension media were employed, the success of this initial study suggests that electrophoresis may be an important mineral fractionation option in fine-grained aggregate processing.

42 CFR 37.20 - Miner identification document.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Miner identification document. 37.20 Section 37.20 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES MEDICAL CARE AND... identification document which includes an occupational history questionnaire shall be completed for each miner at...

Understanding processes affecting mineral deposits in humid environments

USGS Publications Warehouse

Seal, Robert R.; Ayuso, Robert A.

2011-01-01

Recent interdisciplinary studies by the U.S. Geological Survey have resulted in substantial progress toward understanding the influence that climate and hydrology have on the geochemical signatures of mineral deposits and the resulting mine wastes in the eastern United States. Specific areas of focus include the release, transport, and fate of acid, metals, and associated elements from inactive mines in temperate coastal areas and of metals from unmined mineral deposits in tropical to subtropical areas; the influence of climate, geology, and hydrology on remediation options for abandoned mines; and the application of radiogenic isotopes to uniquely apportion source contributions that distinguish natural from mining sources and extent of metal transport. The environmental effects of abandoned mines and unmined mineral deposits result from a complex interaction of a variety of chemical and physical factors. These include the geology of the mineral deposit, the hydrologic setting of the mineral deposit and associated mine wastes, the chemistry of waters interacting with the deposit and associated waste material, the engineering of a mine as it relates to the reactivity of mine wastes, and climate, which affects such factors as temperature and the amounts of precipitation and evapotranspiration; these factors, in turn, influence the environmental behavior of mineral deposits. The role of climate is becoming increasingly important in environmental investigations of mineral deposits because of the growing concerns about climate change.

Enamel mineral loss.

PubMed

West, Nicola X; Joiner, Andrew

2014-06-01

To summarise the chemical, biological and host factors that impact enamel mineral loss, to highlight approaches to contemporary management of clinical conditions involving mineral loss and summarise emerging trends and challenges in this area. "Medline" and "Scopus" databases were searched electronically with the principal key words tooth, enamel, *mineral*, caries and erosion. Language was restricted to English and original studies and reviews were included. Conference papers and abstracts were excluded. Enamel mineral loss leads to the degradation of the surface and subsurface structures of teeth. This can impact their shape, function, sensitivity and aesthetic qualities. Dental caries is a multifactorial disease caused by the simultaneous interplay of dietary sugars, dental plaque, the host and time. There is a steady decline in dental caries in developed countries and the clinical management of caries is moving towards a less invasive intervention, with risk assessment, prevention, control, restoration and recall. Tooth wear can be caused by erosion, abrasion and attrition. Dental erosion can be the result of acid from intrinsic sources, such as gastric acids, or extrinsic sources, in particular from the diet and consumption of acidic foods and drinks. Its prevalence is increasing and it increases with age. Clinical management requires diagnosis and risk assessment to understand the underlying aetiology, so that optimal preventative measures can be implemented. Overall, prevention of enamel mineral loss from caries and tooth wear should form the basis of lifelong dental management. Evidence based oral hygiene and dietary advice is imperative, alongside preventive therapy, to have a healthy lifestyle, whilst retaining hard tooth tissue. © 2014 Elsevier Ltd. All rights reserved.

Review of selected global mineral industries in 2011 and an outlook to 2017

USGS Publications Warehouse

Menzie, W. David; Soto-Viruet, Yadira; Bermúdez-Lugo, Omayra; Mobbs, Philip M.; Perez, Alberto Alexander; Taib, Mowafa; Wacaster, Susan; ,

2013-01-01

This report reviews the world production of selected mineral commodities in 2011 and includes output projections (based on planned capacity expansions) through 2017. It also includes brief discussions of several issues that are of importance to the mineral sector, including the world economy, the availability of strategic minerals, significant company mergers and acquisitions in 2011, exploration investment made during the year, and the moves towards resource nationalization and expropriation of mineral assets by national Governments.

Race for resources: continuing struggles over minerals and fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanzer, M.

1980-01-01

Analyzing the mineral crisis within the historical context of the workings of the international capitalist system is necessary since capitalism spawned the industrial revolution, which in turn led to the vast expansion of mineral use. The analysis begins with the multinational companies that dominate the international mineral industry because they are generally the leading forces in the struggle for control of mineral resources and profits. The focus is twofold: (1) on those minerals that are important as economic inputs and in money value, including the metals copper, bauxite, nickel, and iron ore; and (2) to a lesser extent, on themore » fuels. The emphasis is on the current picture and likely changes in the future. Case studies illustrate some of the major forces at work. Crucial problem areas of the future will include the roles of technology, the Third World, and socialist countries. 26 references, 24 tables.« less

30 CFR 253.41 - What terms must I include in my OSFR evidence?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What terms must I include in my OSFR evidence? 253.41 Section 253.41 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL SPILL FINANCIAL RESPONSIBILITY FOR OFFSHORE FACILITIES Requirements for Submitting OSFR Information § 253.41 What terms must I include in my...

Process for the physical segregation of minerals

DOEpatents

Yingling, Jon C.; Ganguli, Rajive

2004-01-06

With highly heterogeneous groups or streams of minerals, physical segregation using online quality measurements is an economically important first stage of the mineral beneficiation process. Segregation enables high quality fractions of the stream to bypass processing, such as cleaning operations, thereby reducing the associated costs and avoiding the yield losses inherent in any downstream separation process. The present invention includes various methods for reliably segregating a mineral stream into at least one fraction meeting desired quality specifications while at the same time maximizing yield of that fraction.

43 CFR 3873.1 - Segregation of mineral from non-mineral land.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Segregation of mineral from non-mineral...) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) ADVERSE CLAIMS, PROTESTS AND CONFLICTS Segregation § 3873.1 Segregation of mineral from non-mineral land. Where a survey is...

43 CFR 3873.1 - Segregation of mineral from non-mineral land.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Segregation of mineral from non-mineral...) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) ADVERSE CLAIMS, PROTESTS AND CONFLICTS Segregation § 3873.1 Segregation of mineral from non-mineral land. Where a survey is...

43 CFR 3873.1 - Segregation of mineral from non-mineral land.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Segregation of mineral from non-mineral...) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) ADVERSE CLAIMS, PROTESTS AND CONFLICTS Segregation § 3873.1 Segregation of mineral from non-mineral land. Where a survey is...

Geology of the epithermal Ag-Au Huevos Verdes vein system and San José district, Deseado massif, Patagonia, Argentina

NASA Astrophysics Data System (ADS)

Dietrich, Andreas; Gutierrez, Ronald; Nelson, Eric P.; Layer, Paul W.

2012-03-01

The San José district is located in the northwest part of the Deseado massif and hosts a number of epithermal Ag-Au quartz veins of intermediate sulfidation style, including the Huevos Verdes vein system. Veins are hosted by andesitic rocks of the Bajo Pobre Formation and locally by rhyodacitic pyroclastic rocks of the Chon Aike Formation. New 40Ar/39Ar constraints on the age of host rocks and mineralization define Late Jurassic ages of 151.3 ± 0.7 Ma to 144.7 ± 0.1 Ma for volcanic rocks of the Bajo Pobre Formation and of 147.6 ± 1.1 Ma for the Chon Aike Formation. Illite ages of the Huevos Verdes vein system of 140.8 ± 0.2 and 140.5 ± 0.3 Ma are 4 m.y. younger than the volcanic host rock unit. These age dates are among the youngest reported for Jurassic volcanism in the Deseado massif and correlate well with the regional context of magmatic and hydrothermal activity. The Huevos Verdes vein system has a strike length of 2,000 m, with several ore shoots along strike. The vein consists of a pre-ore stage and three main ore stages. Early barren quartz and chalcedony are followed by a mottled quartz stage of coarse saccharoidal quartz with irregular streaks and discontinuous bands of sulfide-rich material. The banded quartz-sulfide stage consists of sulfide-rich bands alternating with bands of quartz and bands of chlorite ± illite. Late-stage sulfide-rich veinlets are associated with kaolinite gangue. Ore minerals are argentite and electrum, together with pyrite, sphalerite, galena, chalcopyrite, minor bornite, covellite, and ruby silver. Wall rock alteration is characterized by narrow (< 3 m) halos of illite and illite/smectite next to veins, grading outward into propylitic alteration. Gangue minerals are dominantly massive quartz intergrown with minor to accessory adularia. Epidote, illite, illite/smectite, and, preferentially at deeper levels, Fe-chlorite gangue indicate near-neutral pH hydrothermal fluids at temperatures of >220°C. Kaolinite occurring with

Evolution of ribozymes in the presence of a mineral surface

PubMed Central

Stephenson, James D.; Popović, Milena; Bristow, Thomas F.

2016-01-01

Mineral surfaces are often proposed as the sites of critical processes in the emergence of life. Clay minerals in particular are thought to play significant roles in the origin of life including polymerizing, concentrating, organizing, and protecting biopolymers. In these scenarios, the impact of minerals on biopolymer folding is expected to influence evolutionary processes. These processes include both the initial emergence of functional structures in the presence of the mineral and the subsequent transition away from the mineral-associated niche. The initial evolution of function depends upon the number and distribution of sequences capable of functioning in the presence of the mineral, and the transition to new environments depends upon the overlap between sequences that evolve on the mineral surface and sequences that can perform the same functions in the mineral's absence. To examine these processes, we evolved self-cleaving ribozymes in vitro in the presence or absence of Na-saturated montmorillonite clay mineral particles. Starting from a shared population of random sequences, RNA populations were evolved in parallel, along separate evolutionary trajectories. Comparative sequence analysis and activity assays show that the impact of this clay mineral on functional structure selection was minimal; it neither prevented common structures from emerging, nor did it promote the emergence of new structures. This suggests that montmorillonite does not improve RNA's ability to evolve functional structures; however, it also suggests that RNAs that do evolve in contact with montmorillonite retain the same structures in mineral-free environments, potentially facilitating an evolutionary transition away from a mineral-associated niche. PMID:27793980

Extracellular electron transfer mechanisms between microorganisms and minerals.

PubMed

Shi, Liang; Dong, Hailiang; Reguera, Gemma; Beyenal, Haluk; Lu, Anhuai; Liu, Juan; Yu, Han-Qing; Fredrickson, James K

2016-10-01

Electrons can be transferred from microorganisms to multivalent metal ions that are associated with minerals and vice versa. As the microbial cell envelope is neither physically permeable to minerals nor electrically conductive, microorganisms have evolved strategies to exchange electrons with extracellular minerals. In this Review, we discuss the molecular mechanisms that underlie the ability of microorganisms to exchange electrons, such as c-type cytochromes and microbial nanowires, with extracellular minerals and with microorganisms of the same or different species. Microorganisms that have extracellular electron transfer capability can be used for biotechnological applications, including bioremediation, biomining and the production of biofuels and nanomaterials.

Critical mineral resources of the United States—An introduction

USGS Publications Warehouse

Schulz, Klaus J.; DeYoung, John H.; Seal, Robert R.; Bradley, Dwight C.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Many changes have taken place in the mineral resource sector since the publication by the U.S. Geological Survey of Professional Paper 820, “United States Mineral Resources,” which is a review of the long-term United States resource position for 65 mineral commodities or commodity groups. For example, since 1973, the United States has continued to become increasingly dependent on imports to meet its demands for an increasing number of mineral commodities. The global demand for mineral commodities is at an alltime high and is expected to continue to increase, and the development of new technologies and products has led to the use of a greater number of mineral commodities in increasing quantities to the point that, today, essentially all naturally occurring elements have several significant industrial uses. Although most mineral commodities are present in sufficient amounts in the earth to provide adequate supplies for many years to come, their availability can be affected by such factors as social constraints, politics, laws, environmental regulations, land-use restrictions, economics, and infrastructure.This volume presents updated reviews of 23 mineral commodities and commodity groups viewed as critical to a broad range of existing and emerging technologies, renewable energy, and national security. The commodities or commodity groups included are antimony, barite, beryllium, cobalt, fluorine, gallium, germanium, graphite, hafnium, indium, lithium, manganese, niobium, platinum-group elements, rare-earth elements, rhenium, selenium, tantalum, tellurium, tin, titanium, vanadium, and zirconium. All these commodities have been listed as critical and (or) strategic in one or more of the recent studies based on assessed likelihood of supply interruption and the possible cost of such a disruption to the assessor. For some of the minerals, current production is limited to only one or a few countries. For many, the United States currently has no mine production or any

Hair Mineral Analysis and Behavior: An Analysis of 51 Studies.

ERIC Educational Resources Information Center

Rimland, Bernard; Larson, Gerald E.

1983-01-01

Fifty-one studies on the relationship between hair mineral levels and human behavior covered a variety of behavior, including learning disabilities, retardation, hyperactivity, autism, and behavior disorders. High levels of certain minerals (especially lead and cadmium) and low levels of other minerals (especially potassium and sodium) associated…

Minerals in thalassaemia major patients: An overview.

PubMed

Ozturk, Zeynep; Genc, Gizem Esra; Gumuslu, Saadet

2017-05-01

Thalassaemia major (TM) is a hereditary blood disease characterised by reduced or absent production of beta globin chains. Erythrocyte transfusions are given to raise the haemoglobin level in patients with thalassaemia major. However, transfusions have been related to increased risk of iron overload and tissue damage related to excess iron. Both elevated oxidative stress due to iron overload and increased hemolysis lead to over utilisation of minerals required for antioxidant enzymes activities. Iron chelators have been used to prevent iron overload in thalassaemia major patients, but these chelators have the possibility of removing minerals from the body. Thalassaemia patients are more at risk for mineral deficiency because of increased oxidative stress and iron chelation therapies. Growth and maturational delay, cardiomyopathy, endocrinopathies and osteoporosis are the complications of thalassaemia. Minerals may play a particular role to prevent these complications. In the current review, we provide an overview of minerals including zinc (Zn), copper (Cu), selenium (Se), magnesium (Mg) and calcium (Ca) in thalassaemia major patients. We, also, underline that some complications of thalassaemia can be caused by an increased need for minerals or lack of the minerals. Copyright © 2017 Elsevier GmbH. All rights reserved.

A thermal emission spectral library of rock-forming minerals

NASA Astrophysics Data System (ADS)

Christensen, Philip R.; Bandfield, Joshua L.; Hamilton, Victoria E.; Howard, Douglas A.; Lane, Melissa D.; Piatek, Jennifer L.; Ruff, Steven W.; Stefanov, William L.

2000-04-01

A library of thermal infrared spectra of silicate, carbonate, sulfate, phosphate, halide, and oxide minerals has been prepared for comparison to spectra obtained from planetary and Earth-orbiting spacecraft, airborne instruments, and laboratory measurements. The emphasis in developing this library has been to obtain pure samples of specific minerals. All samples were hand processed and analyzed for composition and purity. The majority are 710-1000 μm particle size fractions, chosen to minimize particle size effects. Spectral acquisition follows a method described previously, and emissivity is determined to within 2% in most cases. Each mineral spectrum is accompanied by descriptive information in database form including compositional information, sample quality, and a comments field to describe special circumstances and unique conditions. More than 150 samples were selected to include the common rock-forming minerals with an emphasis on igneous and sedimentary minerals. This library is available in digital form and will be expanded as new, well-characterized samples are acquired.

Minerals, Tobacco and Smoking-Related Disease

NASA Astrophysics Data System (ADS)

Stephens, W. E.

2003-12-01

with surfaces highly adsorbent to polycyclic aromatic hydrocarbons (PAH). Calcic mineral particles are two orders of magnitude more abundant in smokers' lungs compared with non-smoking controls in residents of Vancouver. Such particles may thus be potential agents for the delivery of PAH carcinogens, including benzo(a)pyrene, to the lungs. None of the potential hazards listed above has yet been properly evaluated.

Gold deposits of the northern margin of the North China craton: Multiple late Paleozoic-Mesozoic mineralizing events

USGS Publications Warehouse

Hart, C.J.R.; Goldfarb, R.J.; Qiu, Yumin; Snee, L.; Miller, L.D.; Miller, M.L.

2002-01-01

The northern margin of the North China craton is well-endowed with lode gold deposits hosting a resource of approximately 900 tonnes (t) of gold. The ???1,500-km-long region is characterized by east-trending blocks of metamorphosed Archean and Proterozoic strata that were episodically uplifted during Variscan, Indosinian, and Yanshanian deformational and magmatic events. At least 12 gold deposits from the Daqinshan, Yan-Liao (includes the Zhangjiakou, Yanshan, and Chifeng gold districts), and Changbaishan gold provinces contain resources of 20-100 t Au each. Most deposits are hosted in uplifted blocks of Precambrian metamorphic rocks, although felsic Paleozoic and Mesozoic plutons are typically proximal and host ???30% of the deposits. The lodes are characterized by sulfide-poor quartz veins in brittle structures with low base metal values and high Au:Ag ratios. Although phyllic alteration is most common, intensive alkali feldspar metasomatism characterizes the Wulashan, Dongping, and Zhongshangou deposits, but is apparently coeval with Variscan alkalic magmatism only at Wulashan. Stepwise 40Ar-39Ar geochronology on 16 samples from gangue and alteration phases, combined with unpublished SHRIMP U-Pb dates on associated granitoids, suggest that gold mineralizing events occured during Variscan, Indosinian, and Yanshanian orogenies at circa 350, 250, 200, 180, 150, and 129 Ma. However, widespread Permo-Triassic (???250 Ma) and Early Jurassic (???180 Ma) thermal events caused variable resetting of most of the white mica and K-feldspar argon spectra, as well as previously reported K-Ar determinations. Compiled and new stable isotope and fluid inclusion data show that most ??18O values for ore-stage veins range from 8 to 14???, indicating a fluid in equilibrium with the Precambrian metamorphic basement rocks; ??D values from fluid inclysions range widely from -64 to -154???, which is indicative of a local meteoric component in some veins; and highly variable ??34S data

Minerals Yearbook, volume III, Area Reports—International—Asia and the Pacific

USGS Publications Warehouse

Geological Survey, U.S.

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume III, Area Reports—International—Latin America and Canada

USGS Publications Warehouse

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Minerals Yearbook, volume III, Area Reports—International—Europe and Central Eurasia

USGS Publications Warehouse

Geological Survey, U.S.

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

Raman spectroscopy of selected copper minerals of significance in corrosion.

PubMed

Frost, R L

2003-04-01

The Raman spectroscopy of selected minerals of the corrosion products has been measured including nantokite, eriochalcite, claringbullite, atacamite, paratacamite, clinoatacamite and brochantite and related minerals. The free energy of formation shows that each mineral is stable relative to copper metal. The mineral, which is formed in copper corrosion, depends on the kinetics and conditions of the reaction. Raman spectroscopy clearly identifies each mineral by its characteristic Raman spectrum. The Raman spectrum is related to the mineral structure and bands are assigned to CuCl stretching and bending modes and to SO stretching modes. Clinoatacamite is identified as the polymorph of atacamite and not paratacamite. Paratacamite is a separate mineral with a similar but different structure to that of atacamite.

Economics of Lunar Mineral Exploration

NASA Astrophysics Data System (ADS)

Blair, Brad R.

1999-01-01

Exploration of space is increasingly being rationalized by the potential for long-term commercial payoffs. The commercial use of lunar resources is gaining relevance as technology and infrastructure increase, and will depend on an adequate foundation of geological information. While past lunar exploration has provided detailed knowledge about the composition, geologic history and structural characteristics of the lunar surface at six locations, the rest of the Moon remains largely unexplored. The purpose of this paper is to describe traditional methods and decision criteria used in the mineral exploration business. Rationale for terrestrial mineral exploration is firmly entrenched within the context of economic gain, with asset valuation forming the primary feedback to decision making. The paper presents a summary of relevant knowledge from the field of exploration economics, applying it to the case of space mineral development. It includes a description of the current paradigm of both space exploration and terrestrial mineral exploration, as each pertains to setting priorities and decision making. It briefly examines issues related to space resource demand, extraction and transportation to establish its relevance.

Geochemistry of surface-waters in mineralized and non-mineralized areas of the Yukon-Tanana Uplands

USGS Publications Warehouse

Wang, B.; Wanty, R.B.; Vohden, J.

2005-01-01

The U.S. Geological Survey (USGS) and Alaska Department of Natural Resources (ADNR) are continuing investigations on element mobility in mineralized and non-mineralized areas of the Yukon-Tanana Upland in east-central Alaska. The chemistry of stream water is evaluated in the context of regional bedrock geology and geologic structure. Sampling sites were located in the Big Delta B2 quadrangle, which includes the mineralized areas of the Pogo claim block. The area is typified by steep, subarctic-alpine, boreal forest catchment basins. Samples were collected from catchments that either cross structural features and lithologic contacts, or are underlain by a single lithology. Waters are generally dilute (< 213 mg/L TDS), and are classified as Ca2+ and Mg2+-HCO3- to Ca2+ and Mg2+-SO42- waters. Gneissic lithologies are more SO42- dominated than the intrusive units. The major-ion chemistry of the waters reflects a rock-dominated aqueous system. Trace-element concentrations in water are generally low; however, As and Sb are detected near mineralized areas but in most cases rapidly attenuated downstream and processes other than simple dilution are controlling the concentrations of these trace elements. There is a tendency toward increasing SO42- concentrations downstream in waters both proximal and distal to mineralized areas. More work is necessary to determine what proportion of the increase in SO42- could be derived from the oxidation of sulfide minerals as opposed to water influenced by the underlying gneissic units.

Respirable coal dust exposure and respiratory symptoms in South-African coal miners: A comparison of current and ex-miners

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naidoo, R.N.; Robins, T.G.; Seixas, N.

2006-06-15

Dose-response associations between respirable dust exposure and respiratory symptoms and between symptoms and spirometry outcomes among currently employed and formerly employed South-African coal miners were investigated. Work histories, interviews, and spirometry and cumulative exposure were assessed among 684 current and 212 ex-miners. Results: Lower prevalences of symptoms were found among employed compared with ex-miners. Associations with increasing exposure for symptoms of phlegm and past history of tuberculosis were observed, whereas other symptom prevalences were higher in the higher exposure categories. Symptomatic ex-miners exhibited lower lung-function compared to the nonsymptomatic. Compared with published data, symptoms rates were low in current minersmore » but high in ex-miners. Although explanations could include the low prevalence of smoking and/or reporting/selection bias, a 'Survivor' and/or a 'hire' effect is more likely, resulting in an underestimation of the dust-related effect.« less

30 CFR 285.908 - What must I include in my decommissioning notice?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must I include in my decommissioning notice? 285.908 Section 285.908 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE RENEWABLE ENERGY ALTERNATE USES OF EXISTING FACILITIES ON THE OUTER CONTINENTAL SHELF...

An investigation into heterogeneity in a single vein-type uranium ore deposit: Implications for nuclear forensics.

PubMed

Keatley, A C; Scott, T B; Davis, S; Jones, C P; Turner, P

2015-12-01

Minor element composition and rare earth element (REE) concentrations in nuclear materials are important as they are used within the field of nuclear forensics as an indicator of sample origin. However recent studies into uranium ores and uranium ore concentrates (UOCs) have shown significant elemental and isotopic heterogeneity from a single mine site such that some sites have shown higher variation within the mine site than that seen between multiple sites. The elemental composition of both uranium and gangue minerals within ore samples taken along a single mineral vein in South West England have been measured and reported here. The analysis of the samples was undertaken to determine the extent of the localised variation in key elements. Energy Dispersive X-ray spectroscopy (EDS) was used to analyse the gangue mineralogy and measure major element composition. Minor element composition and rare earth element (REE) concentrations were measured by Electron Probe Microanalysis (EPMA). The results confirm that a number of key elements, REE concentrations and patterns used for origin location do show significant variation within mine. Furthermore significant variation is also visible on a meter scale. In addition three separate uranium phases were identified within the vein which indicates multiple uranium mineralisation events. In light of these localised elemental variations it is recommended that representative sampling for an area is undertaken prior to establishing the REE pattern that may be used to identify the originating mine for an unknown ore sample and prior to investigating impact of ore processing on any arising REE patterns. Copyright © 2015 Elsevier Ltd. All rights reserved.

Microbially mediated carbon mineralization: Geoengineering a carbon-neutral mine

NASA Astrophysics Data System (ADS)

Power, I. M.; McCutcheon, J.; Harrison, A. L.; Wilson, S. A.; Dipple, G. M.; Southam, G.

2013-12-01

Ultramafic and mafic mine tailings are a potentially valuable feedstock for carbon mineralization, affording the mining industry an opportunity to completely offset their carbon emissions. Passive carbon mineralization has previously been documented at the abandoned Clinton Creek asbestos mine, and the active Diavik diamond mine and Mount Keith nickel mine, yet the majority of tailings remain unreacted. Examples of microbe-carbonate interactions at each mine suggest that biological pathways could be harnessed to promote carbon mineralization. In suitable environmental conditions, microbes can mediate geochemical processes to accelerate mineral dissolution, increase the supply of carbon dioxide (CO2), and induce carbonate precipitation, all of which may accelerate carbon mineralization. Tailings mineralogy and the availability of a CO2 point source are key considerations in designing tailings storage facilities (TSF) for optimizing carbon mineralization. We evaluate the efficacy of acceleration strategies including bioleaching, biologically induced carbonate precipitation, and heterotrophic oxidation of waste organics, as well as abiotic strategies including enhancing passive carbonation through modifying tailings management practices and use of CO2 point sources (Fig. 1). With the aim of developing carbon-neutral mines, implementation of carbon mineralization strategies into TSF design will be driven by economic incentives and public pressure for environmental sustainability in the mining industry. Figure 1. Schematic illustrating geoengineered scenarios for carbon mineralization of ultramafic mine tailings. Scenarios A and B are based on non-point and point sources of CO2, respectively.

Mineralization/Anti-Mineralization Networks in the Skin and Vascular Connective Tissues

PubMed Central

Li, Qiaoli; Uitto, Jouni

2014-01-01

Ectopic mineralization has been linked to several common clinical conditions with considerable morbidity and mortality. The mineralization processes, both metastatic and dystrophic, affect the skin and vascular connective tissues. There are several contributing metabolic and environmental factors that make uncovering of the precise pathomechanisms of these acquired disorders exceedingly difficult. Several relatively rare heritable disorders share phenotypic manifestations similar to those in common conditions, and, consequently, they serve as genetically controlled model systems to study the details of the mineralization process in peripheral tissues. This overview will highlight diseases with mineral deposition in the skin and vascular connective tissues, as exemplified by familial tumoral calcinosis, pseudoxanthoma elasticum, generalized arterial calcification of infancy, and arterial calcification due to CD73 deficiency. These diseases, and their corresponding mouse models, provide insight into the pathomechanisms of soft tissue mineralization and point to the existence of intricate mineralization/anti-mineralization networks in these tissues. This information is critical for understanding the pathomechanistic details of different mineralization disorders, and it has provided the perspective to develop pharmacological approaches to counteract the consequences of ectopic mineralization. PMID:23665350

Extracellular electron transfer mechanisms between microorganisms and minerals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Liang; Dong, Hailiang; Reguera, Gemma

Electrons can be transferred from microorganisms to multivalent metal ions that are associated with minerals and vice versa. As the microbial cell envelope is neither physically permeable to minerals nor electrically conductive, microorganisms have evolved strategies to exchange electrons with extracellular minerals. In this Review, we discuss the molecular mechanisms that underlie the ability of microorganisms to exchange electrons, such as c-type cytochromes and microbial nanowires, with extracellular minerals and with microorganisms of the same or different species. Microorganisms that have extracellular electron transfer capability can be used for biotechnological applications, including bioremediation, biomining and the production of biofuels andmore » nanomaterials.« less

Assessment of the geoavailability of trace elements from selected zinc minerals

USGS Publications Warehouse

Driscoll, Rhonda L.; Hageman, Phillip L.; Benzel, William M.; Diehl, Sharon F.; Morman, Suzette; Choate, LaDonna M.; Lowers, Heather

2014-01-01

This assessment focused on five zinc-bearing minerals. The minerals were subjected to a number of analyses including quantitative X-ray diffraction, optical microscopy, leaching tests, and bioaccessibility and toxicity studies. Like a previous comprehensive assessment of five copper-bearing minerals, the purpose of this assessment was to obtain structural and chemical information and to characterize the reactivity of each mineral to various simulated environmental and biological conditions. As in the copper minerals study, analyses were conducted consistent with widely accepted methods. Unless otherwise noted, analytical methods used for this study were identical to those described in the investigation of copper-bearing minerals. Two sphalerite specimens were included in the zinc-minerals set. One sphalerite was recovered from a mine in Balmat, New York; the second came from a mine in Creede, Colorado. The location and conditions of origin are significant because, as analyses confirmed, the two sphalerite specimens are quite different. For example, data acquired from a simulated gastric fluid (SGF) study indicate that the hydrothermally formed Creede sphalerite contains orders of magnitude higher arsenic, cadmium, manganese, and lead than the much older metamorphic Balmat sphalerite. The SGF and other experimental results contained in this report suggest that crystallizing conditions such as temperature, pressure, fluidization, or alteration processes significantly affect mineral properties—properties that, in turn, influence reactivity, solubility, and toxicity. The three remaining minerals analyzed for this report—smithsonite, hemimorphite, and hydrozincite—are all secondary minerals or alteration products of zinc-ore deposits. In addition, all share physical characteristics such as tenacity, density, streak, and cleavage. Similarities end there. The chemical composition, unit-cell parameters, acid-neutralizing potential, and other observable and

Variations in organic carbon, aggregation, and enzyme activities of gangue-fly ash-reconstructed soils with sludge and arbuscular mycorrhizal fungi during 6-year reclamation.

PubMed

Yin, Ningning; Zhang, Zhen; Wang, Liping; Qian, Kuimei

2016-09-01

Mining activities can cause drastic disturbances in soil properties, which adversely affect the nutrient cycling and soil environment. As a result, many efforts have been made to explore suitable reclamation strategies that can be applied to accelerate ecology restoration. In this study, we reconstructed mine soils with fly ash, gangue, sludge, planted ryegrass, and inoculated arbuscular mycorrhizal fungi (AMF) in Pangzhuang mine of Xuzhou during 2009 to 2015. The soil aggregation process, enzyme activities (i.e., invertase, urease and acid phosphatase activities), soil organic carbon (SOC) as well as other soil nutrients such as nitrogen, phosphorus, and potassium contents of the reconstructed mine soils were monitored during 6-year reclamation. The integrated application of sludge and AMF led to a promising reclamation performance of mining areas, in which soil aggregate stability, enzyme activities, SOC, and ryegrass biomass were effectively enhanced. The micro-aggregates (< 0.25 mm) decreased with the increase of macro-aggregates (> 0.25 mm) during the reclamation, indicating that macro-aggregates were gradually formed from micro-aggregates during the pedogenesis of reconstructed mine soils. The correlation analysis shows that SOC contents in aggregate fraction of 0.25∼0.5 mm were correlated with aggregate distribution and enzyme activities. Enzyme activities, however, were not significantly correlated with aggregate distribution. The outcomes from the present study could enrich our understanding on soil property changes in pedogenesis process of reconstructed mine soils, and meanwhile, the employment of sludge combined with AMF is suggested to be an effective alternative for the mine soil reclamation.

Historical statistics for mineral and material commodities in the United States

USGS Publications Warehouse

Kelly, Thomas; Matos, Grecia; with Buckingham, David; DiFrancesco, Carl; Porter, Kenneth; Berry, Cyrus; Crane, Melissa; Goonan, Thomas; Sznopek, John

2005-01-01

The U.S. Geological Survey (USGS) provides information to the public and to policy-makers concerning the current use and flow of minerals and materials in the United States economy. The USGS collects, analyzes, and disseminates minerals information on most nonfuel mineral commodities.This USGS digital database is an online compilation of historical U.S. statistics on mineral and material commodities. The database contains information on approximately 90 mineral commodities, including production, imports, exports, and stocks; reported and apparent consumption; and unit value (the real and nominal price in U.S. dollars of a metric ton of apparent consumption). For many of the commodities, data are reported as far back as 1900. Each commodity file includes a document that describes the units of measure, defines terms, and lists USGS contacts for additional information End-use tables complement these statistics by supplying, for most of these commodities, information about the distribution of apparent consumption.This publication draws on more than 125 years of minerals information experience. At the request of the 47th Congress of the United States (1882; 22 Stat. 329), the U.S. Government began the collection and public distribution of these types of data. The Federal agencies responsible for the collection of the data have changed through time. For the years 1882-1924, the USGS collected and published these data; the U.S. Bureau of Mines (USBM) performed these tasks from 1925-95; and in 1996, the responsibilities once again passed to the USGS (following the closure of the USBM) (Mlynarski, 1998).The USGS collects data on a monthly, quarterly, semiannual, and annual basis from more than 18,000 minerals-related producer and consumer establishments that cooperate with the USGS. These companies voluntarily complete about 40,000 canvass forms that survey production, consumption, recycling, stocks, shipments, and other essential information. Data are also gathered from

25 CFR 225.22 - Approval of minerals agreements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... agreement. (1) The written findings shall include an environmental study which meets the requirements of..., studies, data or other information (other than the environmental study required by § 225.24) possessed by... interest of the Indian mineral owner; (2) The minerals agreement does not have adverse cultural, social, or...

25 CFR 225.22 - Approval of minerals agreements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... agreement. (1) The written findings shall include an environmental study which meets the requirements of..., studies, data or other information (other than the environmental study required by § 225.24) possessed by... interest of the Indian mineral owner; (2) The minerals agreement does not have adverse cultural, social, or...

The mangazeya Ag-Pb-Zn vein deposit hosted in sedimentary rocks, Sakha-Yakutia, Russia: Mineral assemblages, fluid inclusions, stable isotopes (C, O, S), and origin

NASA Astrophysics Data System (ADS)

Anikina, E. Yu.; Bortnikov, N. S.; Klubnikin, G. K.; Gamyanin, G. N.; Prokof'ev, V. Yu.

2016-05-01

The succession of mineral assemblages, chemistry of gangue and ore minerals, fluid inclusions, and stable isotopes (C, O, S) in minerals have been studied in the Mangazeya silver-base-metal deposit hosted in terrigenous rocks of the Verkhoyansk Fold-Thrust Belt. The deposit is localized in the junction zone of the Kuranakh Anticlinorium and the Sartanga Synclinorium at the steep eastern limb of the Endybal Anticline. The deposit is situated at the intersection of the regional Nyuektame and North Tirekhtyakh faults. Igneous rocks are represented by the Endybal massif of granodiorite porphyry 97.8 ± 0.9 Ma in age and dikes varying in composition. One preore and three types of ore mineralization separated in space are distinguished: quartz-pyrite-arsenopyrite (I), quartz-carbonate-sulfide (II), and silver-base-metal (III). Quartz and carbonate (siderite) are predominant in ore veins. Ore minerals are represented by arsenopyrite, pyrite, sphalerite, galena, fahlore, and less frequent sulfosalts. Three types of fluid inclusions in quartz differ in phase compositions: two- or three-phase aqueous-carbon dioxide (FI I), carbon dioxide gas (FI II), and two-phase (FI III) containing liquid and a gas bubble. The homogenization temperature and salinity fall within the ranges of 367-217°C and 13.8-2.6 wt % NaCl equiv in FI I; 336-126°C and 15.4-0.8 wt % NaCl equiv in FI III. Carbon dioxide in FI II was homogenized in gas at +30.2 to +15.3°C and at +27.2 to 29.0°C in liquid. The δ34S values for minerals of type I range from-1.8 to +4.7‰ (V-CDT); of type II, from-7.4 to +6.6‰; and of type III, from-5.6 to +7.1‰. δ13C and δ18O vary from-7.0 to-6.7‰ (V-PDB) and from +16.6 to +17.1 (V-SMOW) in siderite-I; from-9.1 to-6.9‰ (V-PDB) and from +14.6 to +18.9 (V-SMOW) in siderite-II; from-5.4 to-3.1‰ (V-PDB) and from +14.6 to +19.5 (V-SMOW) in ankerite; and from-4.2 to-2.9‰ (V-PDB) and from +13.5 to +16.8 (V-SMOW) in calcite. The data on mineral assemblages, fluid

In Brief: Assessing Afghanistan's mineral resources

NASA Astrophysics Data System (ADS)

Showstack, Randy

2007-12-01

Afghanistan has significant amounts of undiscovered nonfuel mineral resources, with copper and iron ore having the most potential for extraction, according to a new U.S. Geological Survey (USGS) assessment. The assessment, done cooperatively with the Afghanistan Geological Survey of the Afghanistan Ministry of Mines, also found indications of significant deposits of colored stones and gemstones (including emeralds, rubies, and sapphires), gold, mercury, sulfur, chromite, and other resources. ``Mineral resource assessments provide government decision-makers and potential private investors with objective, unbiased information on where undiscovered mineral resources may be located, what kinds of resources are likely to occur, and how much of each mineral commodity may exist in them,'' said USGS director Mark Myers. The USGS, in cooperation with the Afghan government, released an oil and gas resources assessment in March 2006 and an earthquake hazards assessment in May 2007. For more information, visit the Web sites: http://afghanistan.cr.usgs.gov and http://www.bgs.ac.uk/afghanminerals/.

43 CFR 3873.1 - Segregation of mineral from non-mineral land.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Segregation of mineral from non-mineral... AND CONFLICTS Segregation § 3873.1 Segregation of mineral from non-mineral land. Where a survey is... satisfactorily established that there are existent prior unpatented mining claims, the segregation of the latter...

U.S. Geological Survey Mineral Resources Program—Mineral resource science supporting informed decisionmaking

USGS Publications Warehouse

Wilkins, Aleeza M.; Doebrich, Jeff L.

2016-09-19

The USGS Mineral Resources Program (MRP) delivers unbiased science and information to increase understanding of mineral resource potential, production, and consumption, and how mineral resources interact with the environment. The MRP is the Federal Government’s sole source for this mineral resource science and information. Program goals are to (1) increase understanding of mineral resource formation, (2) provide mineral resource inventories and assessments, (3) broaden knowledge of the effects of mineral resources on the environment and society, and (4) provide analysis on the availability and reliability of mineral supplies.

Comparative mineral mapping in the Colorado Mineral Belt using AVIRIS and ASTER remote sensing data

USGS Publications Warehouse

Rockwell, Barnaby W.

2013-01-01

This report presents results of interpretation of spectral remote sensing data covering the eastern Colorado Mineral Belt in central Colorado, USA, acquired by the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) and Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensors. This study was part of a multidisciplinary mapping and data integration project at the U.S. Geological Survey that focused on long-term resource planning by land-managing entities in Colorado. The map products were designed primarily for the regional mapping and characterization of exposed surface mineralogy, including that related to hydrothermal alteration and supergene weathering of pyritic rocks. Alteration type was modeled from identified minerals based on standard definitions of alteration mineral assemblages. Vegetation was identified using the ASTER data and subdivided based on per-pixel chlorophyll content (depth of 0.68 micrometer absorption band) and dryness (fit and depth of leaf biochemical absorptions in the shortwave infrared spectral region). The vegetation results can be used to estimate the abundance of fire fuels at the time of data acquisition (2002 and 2003). The AVIRIS- and ASTER-derived mineral mapping results can be readily compared using the toggleable layers in the GeoPDF file, and by using the provided GIS-ready raster datasets. The results relating to mineral occurrence and distribution were an important source of data for studies documenting the effects of mining and un-mined, altered rocks on aquatic ecosystems at the watershed level. These studies demonstrated a high correlation between metal concentrations in streams and the presence of hydrothermal alteration and (or) pyritic mine waste as determined by analysis of the map products presented herein. The mineral mapping results were also used to delineate permissive areas for various mineral deposit types.

Sodium-bicarbonated mineral water decreases aldosterone levels without affecting urinary excretion of bone minerals.

PubMed

Schoppen, Stefanie; Pérez-Granados, Ana M; Carbajal, Angeles; Sarriá, Beatriz; Navas-Carretero, Santiago; Pilar Vaquero, M

2008-06-01

AIM To assess in healthy postmenopausal women the influence of consuming sodium-bicarbonated mineral water on postprandial evolution of serum aldosterone and urinary electrolyte excretion. Eighteen postmenopausal women consumed 500 ml of two sodium-bicarbonated mineral waters (sodium-bicarbonated mineral water 1 and sodium-bicarbonated mineral water 2) and a low-mineral water with a standard meal. Postprandial blood samples were taken at 60, 120, 240, 360 and 420 min and aldosterone concentrations were measured. Postprandial urinary minerals were determined. Urinary and total mineral excretion and urinary mineral concentrations did not differ except for sodium concentration, which was significantly higher with sodium-bicarbonated mineral water 1 than with low-mineral water (P = 0.005). There was a time effect (P = 0.003) on the aldosterone concentration. At 120 min, aldosterone concentrations were lower with sodium-bicarbonated mineral water 1 (P = 0.021) and sodium-bicarbonated mineral water 2 (P = 0.030) compared with low-mineral water. Drinking a sodium-rich bicarbonated mineral water with a meal increases urinary sodium concentration excretion without changes in the excretion of potassium and bone minerals.

Iron Sulfide Minerals Record Microbe-Mineral Interactions in Anoxic Environments

NASA Astrophysics Data System (ADS)

Picard, A.; Gartman, A.; Cosmidis, J.; Clarke, D. R.; Girguis, P. R.

2017-12-01

The precipitation of most minerals in low-temperature environments on Earth is directly or indirectly influenced by the presence of organic substances and/or microbial biomass. Notably, the influence of microorganisms on the formation of Mn and Fe oxides/oxyhydroxides at the surface of the Earth has been well characterized (Chan et al., 2011; Estes et al., 2017). However, an oxygenated atmosphere is a unique feature of planet Earth. It is therefore critical for the search of life on other planetary bodies to characterize microbe-mineral interactions that form in anoxic conditions. Here we explore the role of microorganisms on the formation of iron sulfide minerals, which form under anoxic conditions. On modern Earth, sulfate-reducing microorganisms (SRM) are the major source of dissolved sulfide in low-temperature sedimentary environments. We experimentally demonstrate that SRM play a role in the nucleation and growth of iron sulfide minerals by acting as organic templates. The physical characteristics of the resulting minerals are different from those formed under abiotic conditions. Moreover, upon forming, iron sulfide minerals become associated with organic carbon, producing a potential organo-mineral signature. We also evaluate how the presence of various organic substances affect the formation of abiotic minerals and how this could produce false biosignatures that could be mistaken as biogenic minerals. Chan, C.S., Fakra, S.C., Emerson, D., Fleming, E.J. and Edwards, K.J. (2011) Lithotrophic iron-oxidizing bacteria produce organic stalks to control mineral growth: implications for biosignature formation. Isme Journal 5, 717-727. Estes, E.R., Andeer, P.F., Nordlund, D., Wankel, S.D. and Hansel, C.M. (2017) Biogenic manganese oxides as reservoirs of organic carbon and proteins in terrestrial and marine environments. Geobiology 15, 158-172.

ASEAN Mineral Database and Information System (AMDIS)

NASA Astrophysics Data System (ADS)

Okubo, Y.; Ohno, T.; Bandibas, J. C.; Wakita, K.; Oki, Y.; Takahashi, Y.

2014-12-01

AMDIS has lunched officially since the Fourth ASEAN Ministerial Meeting on Minerals on 28 November 2013. In cooperation with Geological Survey of Japan, the web-based GIS was developed using Free and Open Source Software (FOSS) and the Open Geospatial Consortium (OGC) standards. The system is composed of the local databases and the centralized GIS. The local databases created and updated using the centralized GIS are accessible from the portal site. The system introduces distinct advantages over traditional GIS. Those are a global reach, a large number of users, better cross-platform capability, charge free for users, charge free for provider, easy to use, and unified updates. Raising transparency of mineral information to mining companies and to the public, AMDIS shows that mineral resources are abundant throughout the ASEAN region; however, there are many datum vacancies. We understand that such problems occur because of insufficient governance of mineral resources. Mineral governance we refer to is a concept that enforces and maximizes the capacity and systems of government institutions that manages minerals sector. The elements of mineral governance include a) strengthening of information infrastructure facility, b) technological and legal capacities of state-owned mining companies to fully-engage with mining sponsors, c) government-led management of mining projects by supporting the project implementation units, d) government capacity in mineral management such as the control and monitoring of mining operations, and e) facilitation of regional and local development plans and its implementation with the private sector.

Estimating mineral requirements of Nellore beef bulls fed with or without inorganic mineral supplementation and the influence on mineral balance.

PubMed

Zanetti, D; Godoi, L A; Estrada, M M; Engle, T E; Silva, B C; Alhadas, H M; Chizzotti, M L; Prados, L F; Rennó, L N; Valadares Filho, S C

2017-04-01

The objectives of this study were to quantify the mineral balance of Nellore cattle fed with and without Ca, P, and micromineral (MM) supplementation and to estimate the net and dietary mineral requirement for cattle. Nellore cattle ( = 51; 270.4 ± 36.6 kg initial BW and 8 mo age) were assigned to 1 of 3 groups: reference ( = 5), maintenance ( = 4), and performance ( = 42). The reference group was slaughtered prior to the experiment to estimate initial body composition. The maintenance group was used to collect values of animals at low gain and reduced mineral intake. The performance group was assigned to 1 of 6 treatments: sugarcane as the roughage source with a concentrate supplement composed of soybean meal and soybean hulls with and without Ca, P, and MM supplementation; sugarcane as the roughage source with a concentrate supplement composed of soybean meal and ground corn with and without Ca, P, and MM supplementation; and corn silage as the roughage source with a concentrate supplement composed of soybean meal and ground corn with and without Ca, P, and MM supplementation. Orthogonal contrasts were adopted to compare mineral intake, fecal and urinary excretion, and apparent retention among treatments. Maintenance requirements and true retention coefficients were generated with the aid of linear regression between mineral intake and mineral retention. Mineral composition of the body and gain requirements was assessed using nonlinear regression between body mineral content and mineral intake. Mineral intake and fecal and urinary excretion were measured. Intakes of Ca, P, S, Cu, Zn, Mn, Co, and Fe were reduced in the absence of Ca, P, and MM supplementation ( < 0.05). Fecal excretion of Ca, Cu, Zn, Mn, and Co was also reduced in treatments without supplementation ( < 0.01). Overall, excretion and apparent absorption and retention coefficients were reduced when minerals were not supplied ( < 0.05). The use of the true retention coefficient instead of the true

Practical applications of trace minerals for dairy cattle.

PubMed

Overton, T R; Yasui, T

2014-02-01

Trace minerals have critical roles in the key interrelated systems of immune function, oxidative metabolism, and energy metabolism in ruminants. To date, the primary trace elements of interest in diets for dairy cattle have included Zn, Cu, Mn, and Se although data also support potentially important roles of Cr, Co, and Fe in diets. Trace minerals such as Zn, Cu, Mn, and Se are essential with classically defined roles as components of key antioxidant enzymes and proteins. Available evidence indicates that these trace minerals can modulate aspects of oxidative metabolism and immune function in dairy cattle, particularly during the transition period and early lactation. Chromium has been shown to influence both immune function and energy metabolism of cattle; dairy cows fed Cr during the transition period and early lactation have evidence of improved immune function, increased milk production, and decreased cytological endometritis. Factors that complicate trace mineral nutrition at the farm level include the existence of a large number of antagonisms affecting bioavailability of individual trace minerals and uncertainty in terms of requirements under all physiological and management conditions; therefore, determining the optimum level and source of trace minerals under each specific situation continues to be a challenge. Typical factorial approaches to determine requirements for dairy cattle do not account for nuances in biological function observed with supplementation with various forms and amounts of trace minerals. Trace mineral nutrition modulates production, health, and reproduction in cattle although both formal meta-analysis and informal survey of the literature reveal substantial heterogeneity of response in these outcome variables. The industry has largely moved away from oxide-based programs toward sulfate-based programs; however, some evidence favors shifting supplementation strategies further toward more bioavailable forms of inorganic and organic trace

Minerals Yearbook, volume III, Area Reports—International—Africa and the Middle East

USGS Publications Warehouse

,

2018-01-01

The U.S. Geological Survey (USGS) Minerals Yearbook discusses the performance of the worldwide minerals and materials industries and provides background information to assist in interpreting that performance. Content of the individual Minerals Yearbook volumes follows:Volume I, Metals and Minerals, contains chapters about virtually all metallic and industrial mineral commodities important to the U.S. economy. Chapters on survey methods, summary statistics for domestic nonfuel minerals, and trends in mining and quarrying in the metals and industrial mineral industries in the United States are also included.Volume II, Area Reports: Domestic, contains a chapter on the mineral industry of each of the 50 States and Puerto Rico and the Administered Islands. This volume also has chapters on survey methods and summary statistics of domestic nonfuel minerals.Volume III, Area Reports: International, is published as four separate reports. These regional reports contain the latest available minerals data on more than 180 foreign countries and discuss the importance of minerals to the economies of these nations and the United States. Each report begins with an overview of the region’s mineral industries during the year. It continues with individual country chapters that examine the mining, refining, processing, and use of minerals in each country of the region and how each country’s mineral industry relates to U.S. industry. Most chapters include production tables and industry structure tables, information about Government policies and programs that affect the country’s mineral industry, and an outlook section.The USGS continually strives to improve the value of its publications to users. Constructive comments and suggestions by readers of the Minerals Yearbook are welcomed.

An Expert System for Identification of Minerals in Thin Section.

ERIC Educational Resources Information Center

Donahoe, James Louis; And Others

1989-01-01

Discusses a computer database which includes optical properties of 142 minerals. Uses fuzzy logic to identify minerals from incomplete and imprecise information. Written in Turbo PASCAL for MS-DOS with 128K. (MVL)

Program and Abstracts for Clay Minerals Society 28th Annual Meeting

NASA Technical Reports Server (NTRS)

1991-01-01

This volume contains abstracts that were accepted for presentation at the annual meeting. Some of the main topics covered include: (1) fundamental properties of minerals and methods of mineral analysis; (2) surface chemistry; (3) extraterrestrial clay minerals; (4) geothermometers and geochronometers; (5) smectite, vermiculite, illite, and related reactions; (6) soils and clays in environmental research; (7) kaolinite, halloysite, iron oxides, and mineral transformations; and (8) clays in lakes, basins, and reservoirs.

Evolution of the Bucium Rodu and Frasin magmatic-hydrothermal system, Metaliferi Mountains, Romania

NASA Astrophysics Data System (ADS)

Iatan, Elena Luisa; Berbeleac, Ion; Visan, Madalina; Minut, Adrian; Nadasan, Laurentiu

2013-04-01

The Miocene Bucium Rodu and Frasin maar-diatreme structures and related Au-Ag epithermal low sulfidation with passing to mesothermal mineralizations are located in the Bucium-Rosia Montana-Baia de Aries metallogenetic district, within so called the "Golden Quatrilaterum", in the northeastern part of the Metaliferi Mountains. These structures are situated at about 5 km southeast from Rosia Montana, the largest European Au-Ag deposit. The total reserves for Bucium Rodu-Frasin are estimated at 43.3 Mt with average contents of 1.3 g/t Au and 3 g/t Ag. The Miocene geological evolution of Bucium Rodu and Frasin magmatic-hydrothermal system took place in closely relationships with tectonic, magmatic and metallogenetic activity from Bucium-Rosia Montana-Baia de Aries district in general, and adjacent areas, in special. The hydrothermal alteration is pervasive; adularia followed by phyllic, carbonatization and silicification alterations, usually show a close relationship with the mineralizations. Propylitic alteration occurs dominantly towards the depth; argillic alteration shows a local character. The mineralization occurs in veins, breccias, stockworks and disseminations and is hosted within two volcanic structures emplaced into a sequence of Cretaceous sediments in closely genetically relations with the Miocene phreatomagmatic fracturing and brecciation events. Within Rodu maar-diatreme structure the mineralizations follow especially the contact between the diatreme and Cretaceous flysch. The vein sets with low, moderately and near vertical dippings, cover 400x400m with N-S trend. The most important mineralization style is represented by veins, accompanied by hydrothermal breccias and disseminations. The veins spatial distribution relives as "en echelon" tension veins. They carry gold, minor base metal sulphides (pyrite, chalcopyrite, sphalerite, galena, tetrahedrite, arsenopyrite). Gangue is represented by carbonates (calcite, dolomite, ankerite, siderite, rhodochrosite

Mineral resources of the Atlantic Exclusive Economic Zone

USGS Publications Warehouse

Dillon, William P.

1984-01-01

Potential mineral resources of the Atlantic Exclusive Economic Zone (including the Gulf of Mexico and US Caribbean areas) include petroleum, sand and gravel, phosphorite, placer deposits of heavy mineral sands, ferromanganese nodules, and fresh water. Although major efforts have been made to search for petroleum, the oil and gas resources of the region are well known only in the western Gulf Shelf and more exploration is under way. Heavy-mineral placer deposits, which may be sources of titanium, gold, rare earths, etc. , have been sampled, but the extent and, therefore, economic value of the deposits have not been identified. Sand and gravel, phosphorite, and ferromanganese nodules all are represented by fairly well established deposits, and only modified market conditions would be necessary to cause detailed exploration and mining.

U.S. Geological Survey Mineral Resources Program - Science Supporting Mineral Resource Stewardship

USGS Publications Warehouse

Kropschot, S.J.

2007-01-01

The United States is the world's largest user of mineral resources. We use them to build our homes and cities, fertilize our food crops, and create wealth that allows us to buy goods and services. Individuals rarely use nonfuel mineral resources in their natural state - we buy light bulbs, not the silica, soda ash, lime, coal, salt, tungsten, copper, nickel, molybdenum, iron, manganese, aluminum, and zinc used to convert electricity into light. The USGS Mineral Resources Program (MRP) is the sole Federal source of scientific information and unbiased research on nonfuel mineral potential, production, and consumption, as well as on the environmental effects of minerals. The MRP also provides baseline geochemical, geophysical, and mineral-deposit data used to understand environmental issues related to extraction and use of mineral resources. Understanding how minerals, water, plants, and organisms interact contributes to our understanding of the environment, which is essential for maintaining human and ecosystem health. To support creation of economic and national security policies in a global context, MRP collects and analyzes data on essential mineral commodities from around the world.

43 CFR 3000.8 - Management of Federal minerals from reserved mineral estates.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Management of Federal minerals from reserved mineral estates. 3000.8 Section 3000.8 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERALS...

43 CFR 3000.8 - Management of Federal minerals from reserved mineral estates.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Management of Federal minerals from reserved mineral estates. 3000.8 Section 3000.8 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERALS...

43 CFR 3000.8 - Management of Federal minerals from reserved mineral estates.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Management of Federal minerals from reserved mineral estates. 3000.8 Section 3000.8 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERALS...

43 CFR 3000.8 - Management of Federal minerals from reserved mineral estates.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Management of Federal minerals from reserved mineral estates. 3000.8 Section 3000.8 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERALS...

Active mineral additives of sapropel ashes

NASA Astrophysics Data System (ADS)

Khomich, V. A.; Danilina, E. V.; Krivonos, O. I.; Plaksin, G. V.

2015-01-01

The goal of the presented research is to establish a scientific rational for the possibility of sapropel ashes usage as an active mineral additive. The research included the study of producing active mineral additives from sapropels by their thermal treatment at 850900 °C and afterpowdering, the investigation of the properties of paste matrix with an ash additive, and the study of the ash influence on the cement bonding agent. Thermogravimetric analysis and X-ray investigations allowed us to establish that while burning, organic substances are removed, clay minerals are dehydrated and their structure is broken. Sapropel ashes chemical composition was determined. An amorphous ash constituent is mainly formed from silica of the mineral sapropel part and alumosilicagels resulted from clay minerals decomposition. Properties of PC 400 and PC 500A0 sparopel ash additives were studied. Adding ashes containing Glenium plasticizer to the cement increases paste matrix strength and considerably reduces its water absorption. X-ray phase analysis data shows changes in the phase composition of the paste matrix with an ash additive. Ash additives produce a pozzolanic effect on the cement bonding agent. Besides, an ash additive due to the alumosilicagels content causes transformation from unstable calcium aluminate forms to the stable ones.

Mineral resources and land use in Stanislaus County, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Higgins, C.T.; Dupras, D.L.; Chapman, R.H.

1993-04-01

Stanislaus County covers portions of 3 geologic provinces: Coast Ranges, Great Valley, and Sierra Nevada. Each has been exploited for a distinct set of mineral resources, which include sand and gravel, ball and fire clay, placer gold, manganese, chromite, magnesite, mercury, diatomite, building stone, and mineral pigment. Of these, sand and gravel, clay, and diatomite have been the most important commodities produced recently. Sand and gravel, particularly that along the Tuolumne River, is and will continue to be the county's main mineral product; other potentially important areas include alluvial fans along the west side of the Great Valley. Clay andmore » diatomite could resume importance in the future. There is also potential for quartz-rich specialty sands. Although the county is largely rural, it is undergoing one of the highest growth rates in California. Several new residential communities are being proposed in the county, which would have two major effects on mineral resources: (1) large sources of aggregate will be required for construction, and (2) development of residential areas may preclude mining of resources in those areas. Maps of mineral resources produced by this study, will assist decisions on such potential conflicts in land use.« less

Mineral resource of the month: fluorspar

USGS Publications Warehouse

,

2010-01-01

The article features the industrial mineral fluorspar, used in the manufacture of fluorochemicals, aluminum and steel. It defines fluorspar as crude or beneficiated material, mined or milled for the non-metallic mineral fluorite or calcium fluoride. Applications of acid-grade fluorspar in the U.S. are presented, including production of hydrofluoric acid for chemical production of refrigerants such as chlorofluorocarbons or CFCs. World demand for fluorspar decreased with the CFC ban in the 1990s, but recovered with the use of hydrofluorocarbons or HFCs.

Characteristics of mineral nutrition of plants in the bio-technical life support system with human wastes included in mass exchange

NASA Astrophysics Data System (ADS)

Tikhomirova, Natalia; Ushakova, Sofya; Kalacheva, Galina; Tikhomirov, Alexander

2016-09-01

The study addresses the effectiveness of using ion exchange substrates (IES) to optimize mineral nutrition of plants grown in the nutrient solutions containing oxidized human wastes for application in bio-technical life support systems. The study shows that the addition of IES to the root-inhabited substrate is favorable for the growth of wheat vegetative organs but causes a decrease in the grain yield. By contrast, the addition of IES to the nutrient solution does not influence the growth of vegetative organs but favors normal development of wheat reproductive organs. Thus, to choose the proper method of adjusting the solution with IES, one should take into account specific parameters of plant growth and development and the possibility of multiple recycling of IES based on the liquid products of mineralization of human wastes.

Paragenetic and minor- and trace-element studies of Mississippi Valley-type ore deposits of the Silesian-Cracow district, Poland

USGS Publications Warehouse

Viets, J.G.; Leach, D.L.; Lichte, F.E.; Hopkins, R.T.; Gent, C.A.; Powell, J.W.

1996-01-01

Paragenetic and minor- and trace-element studies were conducted on samples of epigenetic ore and gangue minerals collected from mines and drill core in the Silesian-Cracow (S-C) district of southern Poland. Four discrete mineral suites representing four mineralizing stages can be identified throughout the district. The earliest epigenetic minerals deposited during stage 1 consist of a late dolomite cement together with minor pyrite and marcasite. Stage 2 was the first ore-forming stage and included repetitive deposition of sphalerite and galena in a variety of morphologies. Stage 3 abruptly followed the first ore stage and deposited marcasite and pyrite with variable amounts of late sphalerite and galena. In the samples studied, minerals deposited during stage 3 are predominately marcasite-pyrite with minor sphalerite and galena in the Pomorzany and Olkusz mines, whereas, at the Trzebionka mine, stage 3 mineralization deposited mostly galena and sphalerite with little marcasite or pyrite. Stage 4 minerals include contains barite, followed by calcite, with very minor pyrite and a rare, late granular sphalerite. Compared to other major Mississippi Valley-type (MVT) districts of the world, the Silesian-Cracow district contains sphalerite with the second largest range in Ag concentrations and the largest range in Fe and Cd concentrations of any district. Unlike in other districts, very wide ranges in minor- and trace-element concentrations are also observed in paragenetically equivalent samples collected throughout the district. This wide range indicates that the minor- and trace-element content of the ore-forming environment was highly variable, both spatially and temporally, and suggests that the hydrologic system that the ore fluids traversed from their basinal source was very complex. Throughout the district, a significant increase in Tl, Ge, and As concentrations is accompanied by a lightening of sulfur isotopes between stage 2 and stage 3 minerals. This change

Understanding Contaminants Associated with Mineral Deposits

USGS Publications Warehouse

Verplanck, Philip L.

2008-01-01

Interdisciplinary studies by the U.S. Geological Survey (USGS) have resulted in substantial progress in understanding the processes that control *the release of metals and acidic water from inactive mines and mineralized areas, *the transport of metals and acidic water to streams, and *the fate and effect of metals and acidity on downstream ecosystems. The potential environmental effects associated with abandoned and inactive mines, resulting from the complex interaction of a variety of chemical and physical processes, is an area of study that is important to the USGS Mineral Resources Program. Understanding the processes contributing to the environmental effects of abandoned and inactive mines is also of interest to a wide range of stakeholders, including both those responsible for managing lands with historically mined areas and those responsible for anticipating environmental consequences of future mining operations. The recently completed (2007) USGS project entitled 'Process Studies of Contaminants Associated with Mineral Deposits' focused on abandoned and inactive mines and mineralized areas in the Rocky Mountains of Montana, Colorado, New Mexico, Utah, and Arizona, where there are thousands of abandoned mines. Results from these studies provide new information that advances our understanding of the physical and biogeochemical processes causing the mobilization, transport, reaction, and fate of potentially toxic elements (including aluminum, arsenic, cadmium, copper, iron, lead, and zinc) in mineralized near-surface systems and their effects on aquatic and riparian habitat. These interdisciplinary studies provide the basis for scientific decisionmaking and remedial action by local, State, and Federal agencies charged with minimizing the effects of potentially toxic elements on the environment. Current (2007) USGS research highlights the need to understand (1) the geologic sources of metals and acidity and the geochemical reactions that release them from their

30 CFR 250.241 - What must the DPP or DOCD include?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What must the DPP or DOCD include? 250.241 Section 250.241 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT... and Information Contents of Development and Production Plans (dpp) and Development Operations...

Influence of glutamic acid enantiomers on C-mineralization.

PubMed

Formánek, Pavel; Vranová, Valerie; Lojková, Lea

2015-02-01

Seasonal dynamics in the mineralization of glutamic acid enantiomers in soils from selected ecosystems was determined and subjected to a range of treatments: ambient x elevated CO2 level and meadow x dense x thinned forest environment. Mineralization of glutamic acid was determined by incubation of the soil with 2 mg L- or D-glutamic acid g(-1) of dry soil to induce the maximum respiration rate. Mineralization of glutamic acid enantiomers in soils fluctuates over the course of a vegetation season, following a similar trend across a range of ecosystems. Mineralization is affected by environmental changes and management practices, including elevated CO2 level and thinning intensity. L-glutamic acid metabolism is more dependent on soil type as compared to metabolism of its D-enantiomer. The results support the hypothesis that the slower rate of D- compared to L- amino acid mineralization is due to different roles in anabolism and catabolism of the soil microbial community. © 2014 Wiley Periodicals, Inc.

Metallogenic belt and mineral deposit maps of northeast Asia

USGS Publications Warehouse

Obolenskiy, Alexander A.; Rodionov, Sergey M.; Dejidmaa, Gunchin; Gerel, Ochir; Hwang, Duk-Hwan; Miller, Robert J.; Nokleberg, Warren J.; Ogasawara, Masatsugu; Smelov, Alexander P.; Yan, Hongquan; Seminskiy, Zhan V.

2013-01-01

This report contains explanatory material and summary tables for lode mineral deposits and placer districts (Map A, sheet 1) and metallogenic belts of Northeast Asia (Maps B, C, and D on sheets 2, 3, and 4, respectively). The map region includes eastern Siberia, southeastern Russia, Mongolia, northeast China, and Japan. A large group of geologists—members of the joint international project, Major Mineral Deposits, Metallogenesis, and Tectonics of Northeast Asia—prepared the maps, tables, and introductory text. This is a cooperative project with the Russian Academy of Sciences, Mongolian Academy of Sciences, Mongolian National University, Ulaanbaatar, Mongolian Technical University, Mineral Resources Authority of Mongolia, Geological Research Institute, Jilin University, China Geological Survey, Korea Institute of Geoscience and Mineral Resources, Geological Survey of Japan, and U.S. Geological Survey. This report is one of a series of reports on the mineral resources, geodynamics, and metallogenesis of Northeast Asia. Companion studies include (1) a detailed geodynamics map of Northeast Asia (Parfenov and others, 2003); (2) a compilation of major mineral deposit models (Rodionov and Nokleberg, 2000; Rodionov and others, 2000); (3) a series of metallogenic belt maps (Obolenskiy and others, 2004); (4) location map of lode mineral deposits and placer districts of Northeast Asia (Ariunbileg and others, 2003b); (5) descriptions of metallogenic belts (Rodionov and others, 2004); (6) a database on significant metalliferous and selected nonmetalliferous lode deposits and selected placer districts (Ariunbileg and others, 2003a); and (7) a series of summary project publications (Ariunbileg and 74 others, 2003b).

Mineral Physics and Mantle Evolution

NASA Astrophysics Data System (ADS)

Liebermann, R. C.; Bass, J. D.; Weidner, D. J.

2003-12-01

Don Anderson has been a steadfast patron and constructive critic of mineral physics for more than 40 years. Although he has never actually done an experiment himself [except for perhaps some early work on ice when he was working in Greenland], he has nurtured and supported two generations of experimental mineral physicists throughout the U.S. His role and influence have been especially evident in studies of the elasticity and anelasticity of minerals and the use of such data for interpretation of seismic models of the Earth's mantle. In the 1960s, such acoustic experiments required specimens of centimeter dimensions and could achieve elevated conditions of less than 1 Gigapascal in pressure and a few hundred degrees of Celsius temperature. Today, one can perform such experiments on specimens only a fraction of a milimeter in size and reach pressures of tens of GPa and temperatures in excess of two thousand degrees C. In addition, Anderson's contributions to organized scientific endeavors have extended far beyond his founding role in IRIS to include advising on the establishment of the new Consortium for Materials Properties Research in Earth Sciences [COMPRES]. We ilustrate his remarkable contributions to mineral physics with examples of our own research, some of it done in collaboration with Anderson.

1995 annual report on Alaska's mineral resources

USGS Publications Warehouse

Schneider, Jill L.

1995-01-01

Section 1011 of the Alaska National Interest Lands Conservation Act (ANILCA) of 1980, as amended, requires that "On or before October 1, 1982, and annually thereafter, the President shall transmit to the Congress all pertinent public information relating to minerals in Alaska gathered by the United States Geological Surveys, United States Bureau of Mines, and any other Federal agency." This report has been prepared in response to that requirement. This circular is the fourteenth in the series of annual mineral reports mandated by the ANILCA. The report provides information about current Alaskan mineral projects and events during 1994; the emphasis is on Federal activity. The report addresses both onshore and offshore areas of Alaska.The U.S. Geological Survey (USGS), U.S. Bureau of Mines (USBM), and Minerals Management Service (MMS) are the principal Federal agencies that publish information about energy and mineral resources in Alaska. Their reports and data form the basis for decisions by other Federal agencies regarding land use, access, environmental impacts, and mining claim evaluation. The time required for sample analysis, data synthesis, and publication is lengthy; as a result, scientific reports are generally issued a year or more after initial sample and data collection. Other sources of information for this report include additional Federal and State publications, trade and professional journals, presentations at public meetings and hearings, and press releases. Information is provided for two broad categories of minerals: energy resources and nonfuel-mineral resources.

Geomicrobiology in oceanography: microbe-mineral interactions at and below the seafloor.

PubMed

Edwards, Katrina J; Bach, Wolfgang; McCollom, Thomas M

2005-09-01

Oceanography is inherently interdisciplinary and, since its inception, has included the study of microbe-mineral interactions. From early studies of manganese nodules, to the discovery of hydrothermal vents, it has been recognized that microorganisms are involved at various levels in the transformation of rocks and minerals at and below the seafloor. Recent studies include mineral weathering at low temperatures and microbe-mineral interactions in the subseafloor "deep biosphere". A common characteristic of seafloor and subseafloor geomicrobiological processes that distinguishes them from terrestrial or near-surface processes is that they occur in the dark, one or more steps removed from the sunlight that fuels the near-surface biosphere on Earth. This review focuses on geomicrobiological studies and energy flow in dark, deep-ocean and subseafloor rock habitats.

Geochemistry and Minerality of Wine

NASA Astrophysics Data System (ADS)

Oze, C.; Horton, T. W.; Beaman, M.

2010-12-01

Kaolinite (Al2Si2O5(OH)4) and gibbsite (Al(OH)3) are capable of forming in a variety of environments including anthropogenic solutions such as wine. Here, we evaluate the geochemistry of twelve white wines in order to assess the potential relationship between kaolinite/gibbsite saturation and minerality, a common wine descriptor used to express the rock and/or soil character in the aromas and flavors of wines. Aluminum and Si concentrations ranged from 228-1,281 µg L-1 and 6,583-19,746 µg L-1, respectively, where Si and Al are the only elements to demonstrate positive covariance with minerality scores. Sulfur levels varied from 25,013-167,383 µg L-1 and show the strongest negative covariance with minerality scores. However, like all of the elements studied (Al, Si, Na, Mg, S, K, Ca, and Fe), these trends were not significantly different than random at the 95% confidence level. In contrast, the relative degrees of gibbsite/kaolinite saturation display strong positive covariance with minerality scores and these trends are not random at the greater than 95% confidence level. Overall, our tasters were able to accurately assess the degree of gibbsite/kaolinite saturation amongst the twelve wines based on the objective of assessing minerality. Although the wines were undersaturated with respect to gibbsite/kaolinite, geochemical modeling reveals that increasing the wines’ pHs from ~3.3 to 4.1-4.6 (which is achievable on the palate where saliva has a pH of 7.4) results in gibbsite/kaolinite oversaturation. By considering that minerality is a function of gibbsite/kaolinite saturation and decreasing S, the origin of minerality’s taste and chemical origin in wine with known physical standards becomes increasingly crystalline.

Strata-bound Fe-Co-Cu-Au-Bi-Y-REE deposits of the Idaho Cobalt Belt: Multistage hydrothermal mineralization in a magmatic-related iron oxide copper-gold system

USGS Publications Warehouse

Slack, John F.

2012-01-01

Mineralogical and geochemical studies of strata-bound Fe-Co-Cu-Au-Bi-Y-rare-earth element (REE) deposits of the Idaho cobalt belt in east-central Idaho provide evidence of multistage epigenetic mineralization by magmatic-hydrothermal processes in an iron oxide copper-gold (IOCG) system. Deposits of the Idaho cobalt belt comprise three types: (1) strata-bound sulfide lenses in the Blackbird district, which are cobaltite and, less commonly, chalcopyrite rich with locally abundant gold, native bismuth, bismuthinite, xenotime, allanite, monazite, and the Be-rich silicate gadolinite-(Y), with sparse uraninite, stannite, and Bi tellurides, in a gangue of quartz, chlorite, biotite, muscovite, garnet, tourmaline, chloritoid, and/or siderite, with locally abundant fluorapatite or magnetite; (2) discordant tourmalinized breccias in the Blackbird district that in places have concentrations of cobaltite, chalcopyrite, gold, and xenotime; and (3) strata-bound magnetite-rich lenses in the Iron Creek area, which contain cobaltiferous pyrite and locally sparse chalcopyrite or xenotime. Most sulfide-rich deposits in the Blackbird district are enclosed by strata-bound lenses composed mainly of Cl-rich Fe biotite; some deposits have quartz-rich envelopes.Whole-rock analyses of 48 Co- and/or Cu-rich samples show high concentrations of Au (up to 26.8 ppm), Bi (up to 9.16 wt %), Y (up to 0.83 wt %), ∑REEs (up to 2.56 wt %), Ni (up to 6,780 ppm), and Be (up to 1,180 ppm), with locally elevated U (up to 124 ppm) and Sn (up to 133 ppm); Zn and Pb contents are uniformly low (≤821 and ≤61 ppm, respectively). Varimax factor analysis of bulk compositions of these samples reveals geochemically distinct element groupings that reflect statistical associations of monazite, allanite, and xenotime; biotite and gold; detrital minerals; chalcopyrite and sparse stannite; quartz; and cobaltite with sparse selenides and tellurides. Significantly, Cu is statistically separate from Co and As

Fungal degradation of calcium-, lead- and silicon-bearing minerals.

PubMed

Adeyemi, Ademola O; Gadd, Geoffrey M

2005-06-01

The aim of this study was to examine nutritional influence on the ability of selected filamentous fungi to mediate biogenic weathering of the minerals, apatite, galena and obsidian in order to provide further understanding of the roles of fungi as biogeochemical agents, particularly in relation to the cycling of metals and associated elements found in minerals. The impact of three organic acid producing fungi (Aspergillus niger, Serpula himantioides and Trametes versicolor) on apatite, galena and obsidian was examined in the absence and presence of a carbon and energy source (glucose). Manifestation of fungal weathering included corrosion of mineral surfaces, modification of the mineral substrate through transformation into secondary minerals (i.e. crystal formation) and hyphal penetration of the mineral substrate. Physicochemical interactions of fungal metabolites, e.g. H+ and organic acids, with the minerals are thought to be the primary driving forces responsible. All experimental fungi were capable of mineral surface colonization in the absence and presence of glucose but corrosion of the mineral surface and secondary mineral formation were affected by glucose availability. Only S. himantioides and T. versicolor were able to corrode apatite in the absence of glucose but none of the fungi were capable of doing so with the other minerals. In addition, crystal formation with galena was entirely dependent on the availability of glucose. Penetration of the mineral substrates by fungal hyphae occurred but this did not follow any particular pattern. Although the presence of glucose in the media appeared to influence positively the mineral penetrating abilities of the fungi, the results obtained also showed that some geochemical change(s) might occur under nutrient-limited conditions. It was, however, unclear whether the hyphae actively penetrated the minerals or were growing into pre-existing pores or cracks.

Evaluation of accessible mineral surface areas for improved prediction of mineral reaction rates in porous media

NASA Astrophysics Data System (ADS)

Beckingham, Lauren E.; Steefel, Carl I.; Swift, Alexander M.; Voltolini, Marco; Yang, Li; Anovitz, Lawrence M.; Sheets, Julia M.; Cole, David R.; Kneafsey, Timothy J.; Mitnick, Elizabeth H.; Zhang, Shuo; Landrot, Gautier; Ajo-Franklin, Jonathan B.; DePaolo, Donald J.; Mito, Saeko; Xue, Ziqiu

2017-05-01

experimental data. While the fit of the effluent chemistry (and inferred mineral dissolution rates) greatly improve when the pore-accessible mineral surface areas are used, it was also necessary to include highly reactive glass phases to match the experimental observations, in agreement with conclusions from the disaggregated sediment experiment. It is hypothesized here that the 10-20 reduction in reactive surface areas based on the limited pore accessibility of reactive phases in core flood experiment may be reasonable for poorly sorted and cemented sediments like those at the Nagaoka site, although this reflects pore rather than larger scale heterogeneity.

Gestational form of Selenium in Free-Choice Mineral Mixes Affects Transcriptome Profiles of the Neonatal Calf Testis, Including those of Steroidogenic and Spermatogenic Pathways.

PubMed

Cerny, K L; Garbacik, S; Skees, C; Burris, W R; Matthews, J C; Bridges, P J

2016-01-01

In areas where soils are deficient in Selenium (Se), dietary supplementation of this trace mineral directly to cattle is recommended. Because Se status affects testosterone synthesis and frequency of sperm abnormalities, and the form of Se supplemented to cows affects tissue-specific gene expression, the objective of this study was to determine whether the form of Se consumed by cows during gestation would affect the expression of mRNAs that regulate steroidogenesis and/or spermatogenesis in the neonatal calf testis. Twenty-four predominantly Angus cows were assigned randomly to have individual, ad libitum, access of a mineral mix containing 35 ppm of Se in free-choice vitamin-mineral mixes as either inorganic (ISe), organic (OSe), or a 50/50 mix of ISe and OSe (MIX), starting 4 months prior to breeding and continuing throughout gestation. Thirteen male calves were born over a 3-month period (ISe, n = 5; OSe, n = 4; MIX, n = 4), castrated within 2 days of birth, and extracted testis RNA subjected to transcriptomal analysis by microarray (Affymetrix Bovine 1.0 ST arrays) and targeted gene expression analysis by real-time reverse-transcription PCR (RT-PCR) of mRNAs encoding proteins known to affect steroidogenesis and/or spermatogenesis. The form of dam Se affected (P < 0.05) the expression of 853 annotated genes, including 17 mRNAs putatively regulating steroidogenesis and/or spermatogenesis. Targeted RT-PCR analysis indicated that the expression of mRNA encoding proteins CYP2S1 (cytochrome P450, family 2, subfamily S, polypeptide 1), HSD17B7 (hydroxysteroid (17β) dehydrogenase 7), SULT1E1 (sulfotransferase family 1E, estrogen preferring, member 1), LDHA (lactate dehydrogenase A), CDK5R1 (cyclin-dependent kinase 5, regulatory subunit 1), and LEP (leptin) was affected (P < 0.05) by form of Se consumed by dams of developing bull calves, while AKR1C4 (aldo-keto reductase family 1, member C4) and CCND2 (cyclin D2) tended (P < 0.09) to be

Animal...Vegetable...or Mineral?

ERIC Educational Resources Information Center

Cameron, Eugene

1973-01-01

Outlines the problems facing the United States with mineral reserves being depleted, and the consumption of minerals outstripping production. Expresses concern about the deteriorating mineral position, and the ignorance and confusion of the public with respect to mineral production and supply, energy requirements, and environmental consequences.…

Clay mineral type effect on bacterial enteropathogen survival in soil.

PubMed

Brennan, Fiona P; Moynihan, Emma; Griffiths, Bryan S; Hillier, Stephen; Owen, Jason; Pendlowski, Helen; Avery, Lisa M

2014-01-15

Enteropathogens released into the environment can represent a serious risk to public health. Soil clay content has long been known to have an important effect on enteropathogen survival in soil, generally enhancing survival. However, clay mineral composition in soils varies, and different clay minerals have specific physiochemical properties that would be expected to impact differentially on survival. This work investigated the effect of clay materials, with a predominance of a particular mineral type (montmorillonite, kaolinite, or illite), on the survival in soil microcosms over 96 days of Listeria monocytogenes, Salmonella Dublin, and Escherichia coli O157. Clay mineral addition was found to alter a number of physicochemical parameters in soil, including cation exchange capacity and surface area, and this was specific to the mineral type. Clay mineral addition enhanced enteropathogen survival in soil. The type of clay mineral was found to differentially affect enteropathogen survival and the effect was enteropathogen-specific. © 2013.

An overview of vertebrate mineralization with emphasis on collagen-mineral interaction

NASA Technical Reports Server (NTRS)

Landis, W. J.

1999-01-01

The nucleation, growth, and development of mineral crystals through their interaction principally with collagen in normal bone and calcifying tendon have been elaborated by applying a number of different techniques for analysis of the inorganic and organic constituents of these tissues. The methods have included conventional and high voltage electron microscopy, electron diffraction, microscopic tomography and 3D image reconstruction, and atomic force microscopy. This summary presents results of these studies that have now characterized the size, shape, and aspects of the chemical nature of the crystals as well as their orientation, alignment, location, and distribution with respect to collagen. These data have provided the means for understanding more completely the formation and strength of the collagen-mineral composite present in most vertebrate calcifying tissues and, from that information, a basis for the adaptation of such tissues under mechanical constraints. In the context of the latter point, other data are given showing effects on collagen in bone cell cultures subjected to the unloading parameters of spaceflight. Implications of these results may be particularly relevant to explaining loss of bone by humans and other vertebrate animals during missions in space, during situations of extended fracture healing, long-term bedrest, physical immobilization, and related conditions. In a broader sense, the data speak to the response of bone and mineralized vertebrate tissues to changes in gravitational loading and applied mechanical forces in general.

30 CFR 285.626 - What must I include in my COP?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What must I include in my COP? 285.626 Section 285.626 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT... CONTINENTAL SHELF Plans and Information Requirements Contents of the Construction and Operations Plan § 285...

[Mineral water as a cure].

PubMed

Nocco, Priska Binz

2008-01-01

was to attribute, on the one hand to the physico-chemical properties of the water and on the other hand to the climatic, nutritional and social factors characterising the selected health resort. All over Europe, pharmacists were dealing with mineral waters, among them even very famous names such as Klaproth, Trommsdorf, Lampadius and Fresenius. They were on one side involved in the development and analysis of the waters, while on the other side they were interested in their artificial production. Their knowledge and findings in the area of the mineral water source chemistry gave a crucial impetus to the future evolution of analytic chemistry. Following the improvements in the precision of analysis and classification of the composition of the mineral waters, the imitation of artificial mineral waters increased significantly. Certain pharmacists tried to copy well-known mineral waters in their properly furnished laboratories. At the same time, pharmacies were important sales points: natural and artificial mineral waters as well as their dried components were either sold there, or delivered upon prescription. In the second part of this work, specifically concerning the situation in the Canton Tessin, the most important local sources and spa resorts are described, as well as the analyses performed and the researchers involved. Moreover, the types of therapies used at that time are mentioned. The integration of the local mineral waters into the pharmacopoeia of the Canton Tessin, the Farmacopea Ticinese, is also discussed. Of particular interest are the delivery and the sale of mineral waters and their dried components by a local pharmacy. In the Canton Tessin, the five most frequented spa resorts were Acquarossa, Brissago, Craveggia, Rovio and Stabio. Craveggia spa resort is of course based in Italy; it has however been included in the present work due to its proximity to Switzerland and to a connected historical Substantial differences existed among the individual health

Assessment of critical minerals: Updated application of an early-warning screening methodology

USGS Publications Warehouse

McCullough, Erin A.; Nassar, Nedal

2017-01-01

Increasing reliance on non-renewable mineral resources reinforces the need for identifying potential supply constraints before they occur. The US National Science and Technology Council recently released a report that outlines a methodology for screening potentially critical minerals based on three indicators: supply risk (R), production growth (G), and market dynamics (M). This early-warning screening was initially applied to 78 minerals across the years 1996 to 2013 and identified a subset of minerals as “potentially critical” based on the geometric average of these indicators—designated as criticality potential (C). In this study, the screening methodology has been updated to include data for 2014, as well as to incorporate revisions and modifications to the data, where applicable. Overall, C declined in 2014 for the majority of minerals examined largely due to decreases in production concentration and price volatility. However, the results vary considerably across minerals, with some minerals, such as gallium, recording increases for all three indicators. In addition to assessing magnitudinal changes, this analysis also examines the significance of the change relative to historical variation for each mineral. For example, although mined nickel’s R declined modestly in 2014 in comparison to that of other minerals, it was by far the largest annual change recorded for mined nickel across all years examined and is attributable to Indonesia’s ban on the export of unprocessed minerals. Based on the 2014 results, 20 minerals with the highest C values have been identified for further study including the rare earths, gallium, germanium, rhodium, tantalum, and tungsten.

Grouping Minerals by Their Formulas

ERIC Educational Resources Information Center

Mulvey, Bridget

2018-01-01

Minerals are commonly taught in ways that emphasize mineral identification for its own sake or maybe to help identify rocks. But how do minerals fit in with other science content taught? The author uses mineral formulas to help Earth science students wonder about the connection between elements, compounds, mixtures, minerals, and mineral formulas.…

Mineral potential modelling of gold and silver mineralization in the Nevada Great Basin - a GIS-based analysis using weights of evidence

USGS Publications Warehouse

Mihalasky, Mark J.

2001-01-01

The distribution of 2,690 gold-silver-bearing occurrences in the Nevada Great Basin was examined in terms of spatial association with various geological phenomena. Analysis of these relationships, using GIS and weights of evidence modelling techniques, has predicted areas of high mineral potential where little or no mining activity exists. Mineral potential maps for sedimentary (?disseminated?) and volcanic (?epithermal?) rock-hosted gold-silver mineralization revealed two distinct patterns that highlight two sets of crustal-scale geologic features that likely control the regional distribution of these deposit types. The weights of evidence method is a probability-based technique for mapping mineral potential using the spatial distribution of known mineral occurrences. Mineral potential maps predicting the distribution of gold-silver-bearing occurrences were generated from structural, geochemical, geomagnetic, gravimetric, lithologic, and lithotectonic-related deposit-indicator factors. The maps successfully predicted nearly 70% of the total number of known occurrences, including ~83% of sedimentary and ~60% of volcanic rock-hosted types. Sedimentary and volcanic rockhosted mineral potential maps showed high spatial correlation (an area cross-tabulation agreement of 85% and 73%, respectively) with expert-delineated mineral permissive tracts. In blind tests, the sedimentary and volcanic rock-hosted mineral potential maps predicted 10 out of 12 and 5 out of 5 occurrences, respectively. The key mineral predictor factors, in order of importance, were determined to be: geology (including lithology, structure, and lithotectonic terrane), geochemistry (indication of alteration), and geophysics. Areas of elevated sedimentary rock-hosted mineral potential are generally confined to central, north-central, and north-eastern Nevada. These areas form a conspicuous ?V?-shape pattern that is coincident with the Battle Mountain-Eureka (Cortez) and Carlin mineral trends and a

Iowa State Mining and Mineral Resources Research Institute

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1990-08-01

This final report describes the activities of the Iowa State Mining and Mineral Resources Research Institute (ISMMRRI) at Iowa State University for the period July 1, 1989, to June 30, 1990. Activities include research in mining- and mineral-related areas, education and training of scientists and engineers in these fields, administration of the Institute, and cooperative interactions with industry, government agencies, and other research centers. During this period, ISMMRRI has supported research efforts to: (1) Investigate methods of leaching zinc from sphalerite-containing ores. (2) Study the geochemistry and geology of an Archean gold deposit and of a gold-telluride deposit. (3) Enchancemore » how-quality aggregates for use in construction. (4) Pre-clean coal by triboelectric charging in a fluidized-bed. (5) Characterize the crystal/grain alignment during processing of yttrium-barium-copper-perovskite (1-2-3) superconductors. (5) Study the fluid inclusion properties of a fluorite district. (6) Study the impacts of surface mining on community planning. (7) Assess the hydrophobicity of coal and pyrite for beneficiation. (8) Investigate the use of photoacoustic absorption spectroscopy for monitoring unburnt carbon in the exhaust gas from coal-fired boilers. The education and training program continued within the interdepartmental graduate minor in mineral resources includes courses in such areas as mining methods, mineral processing, industrial minerals, extractive metallurgy, coal science and technology, and reclamation of mined land. In addition, ISMMRRI hosted the 3rd International Conference on Processing and Utilization of High-Sulfur Coals in Ames, Iowa. The Institute continues to interact with industry in order to foster increased cooperation between academia and the mining and mineral community.« less

Supply of and demand for selected energy related mineral commodities

USGS Publications Warehouse

Sibley, Scott F.

2010-01-01

In this report, subjects discussed include components of mineral supply, production, and consumption data, and information on selected mineral commodities in which the Energy Critical Elements Study Group has an interest, and U.S. Geological Survey (USGS) recycling studies, with some results of these studies.

Effects of Chinese mineral strategies on the U.S. minerals industry

USGS Publications Warehouse

McCartan, L.; Menzie, W.D.; Morse, D.E.; Papp, J.F.; Plunkert, P.A.; Tse, P.-K.

2006-01-01

For more than two decades now, China has been undergoing rapid economic growth and industrialization. The industrialization and urbanization of the once rural, farming nation is leading to increased consumption of mineral commodities to build infrastructure and to make into consumer goods. This increased consumption has led to higher mineral prices, lower stocks and, in some cases, temporary shortages of minerals. Chinese mineral producers and manufacturers are responding by building capacity, restructuring and modernizing industrial sectors and establishing international network that compete with those of the United States and other nations.

30 CFR 285.610 - What must I include in my SAP?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What must I include in my SAP? 285.610 Section 285.610 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT... CONTINENTAL SHELF Plans and Information Requirements Contents of the Site Assessment Plan § 285.610 What must...

30 CFR 285.645 - What must I include in my GAP?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What must I include in my GAP? 285.645 Section 285.645 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT, DEPARTMENT... CONTINENTAL SHELF Plans and Information Requirements Contents of the General Activities Plan § 285.645 What...

Effects of Different Mineral Admixtures on the Properties of Fresh Concrete

PubMed Central

Nuruddin, Muhammad Fadhil; Shafiq, Nasir

2014-01-01

This paper presents a review of the properties of fresh concrete including workability, heat of hydration, setting time, bleeding, and reactivity by using mineral admixtures fly ash (FA), silica fume (SF), ground granulated blast furnace slag (GGBS), metakaolin (MK), and rice husk ash (RHA). Comparison of normal and high-strength concrete in which cement has been partially supplemented by mineral admixture has been considered. It has been concluded that mineral admixtures may be categorized into two groups: chemically active mineral admixtures and microfiller mineral admixtures. Chemically active mineral admixtures decrease workability and setting time of concrete but increase the heat of hydration and reactivity. On the other hand, microfiller mineral admixtures increase workability and setting time of concrete but decrease the heat of hydration and reactivity. In general, small particle size and higher specific surface area of mineral admixture are favourable to produce highly dense and impermeable concrete; however, they cause low workability and demand more water which may be offset by adding effective superplasticizer. PMID:24701196

Effects of different mineral admixtures on the properties of fresh concrete.

PubMed

Khan, Sadaqat Ullah; Nuruddin, Muhammad Fadhil; Ayub, Tehmina; Shafiq, Nasir

2014-01-01

This paper presents a review of the properties of fresh concrete including workability, heat of hydration, setting time, bleeding, and reactivity by using mineral admixtures fly ash (FA), silica fume (SF), ground granulated blast furnace slag (GGBS), metakaolin (MK), and rice husk ash (RHA). Comparison of normal and high-strength concrete in which cement has been partially supplemented by mineral admixture has been considered. It has been concluded that mineral admixtures may be categorized into two groups: chemically active mineral admixtures and microfiller mineral admixtures. Chemically active mineral admixtures decrease workability and setting time of concrete but increase the heat of hydration and reactivity. On the other hand, microfiller mineral admixtures increase workability and setting time of concrete but decrease the heat of hydration and reactivity. In general, small particle size and higher specific surface area of mineral admixture are favourable to produce highly dense and impermeable concrete; however, they cause low workability and demand more water which may be offset by adding effective superplasticizer.

Mineral Resources Data System (MRDS)

USGS Publications Warehouse

Mason, G.T.; Arndt, R.E.

1996-01-01

The U.S. Geological Survey (USGS) operates the Mineral Resources Data System (MRDS), a digital system that contained 111,955 records on Sept. 1, 1995. Records describe metallic and industrial commodity deposits, mines, prospects, and occurrences in the United States and selected other countries. These records have been created over the years by USGS commodity specialists and through cooperative agreements with geological surveys of U.S. States and other countries. This CD-ROM contains the complete MRDS data base, several subsets of it, and software to allow data retrieval and display. Data retrievals are made by using GSSEARCH, a program that is included on this CD-ROM. Retrievals are made by specifying fields or any combination of the fields that provide information on deposit name, location, commodity, deposit model type, geology, mineral production, reserves, and references. A tutorial is included. Retrieved records may be printed or written to a hard disk file in four different formats: ascii, fixed, comma delimited, and DBASE compatible.

43 CFR 3594.5 - Minerals soluble in water; brines; minerals taken in solution.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Minerals soluble in water; brines; minerals taken in solution. 3594.5 Section 3594.5 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SOLID MINERALS (OTHER THAN COAL) EXPLORATION AND...

Assessment of the geoavailability of trace elements from minerals in mine wastes: analytical techniques and assessment of selected copper minerals

USGS Publications Warehouse

Driscoll, Rhonda; Hageman, Phillip L.; Benzel, William M.; Diehl, Sharon F.; Adams, David T.; Morman, Suzette; Choate, LaDonna M.

2012-01-01

In this study, four randomly selected copper-bearing minerals were examined—azurite, malachite, bornite, and chalcopyrite. The objectives were to examine and enumerate the crystalline and chemical properties of each of the minerals, to determine which, if any, of the Cu-bearing minerals might adversely affect systems biota, and to provide a multi-procedure reference. Laboratory work included use of computational software for quantifying crystalline and amorphous material and optical and electron imaging instruments to model and project crystalline structures. Chemical weathering, human fluid, and enzyme simulation studies were also conducted. The analyses were conducted systematically: X-ray diffraction and microanalytical studies followed by a series of chemical, bio-leaching, and toxicity experiments.

Bone mineralization in childhood and adolescence.

PubMed

Bachrach, L K

1993-08-01

Prevention of osteoporosis depends on establishing adequate peak bone mass in the first two decades of life. Achievement of this goal requires an understanding of factors that promote skeletal health. Genetic factors are important determinants of adult bone mass, but nonheritable variables, including body mass, calcium nutriture, sex steroids, and activity can strongly influence whether maximal bone mineral is achieved. Acquisition of bone mineral continues throughout childhood and adolescence, reaching a lifetime maximum in early adulthood. Adolescence is a particularly critical time for bone mineral accretion as more than half of the bone calcium is normally laid down during the teen years. Chronic illness, malnutrition, or endocrine deficiencies at this age may result in profound deficits in bone mass, which may not be fully reversible. These risk factors contribute to the osteopenia associated with anorexia nervosa, exercise-induced amenorrhea, delayed puberty, Turner's syndrome, and growth hormone deficiency.

Specificity of pyrometamorphic minerals of the ellestadite group

NASA Astrophysics Data System (ADS)

Zateeva, S. N.; Sokol, E. V.; Sharygin, V. V.

2007-12-01

Numerous rare and new mineral species are synthesized during the process of pyrometamorphism (Gross, 1977; Chesnokov et al., 1987; Chesnokov and Shcherbakova, 1991; Chesnokov, 1999), including silicooxides, chloride-, fluoride, and sulfate-silicates, carbonate-sulfides, chloride-oxides, etc. Having made sense of numerous findings of compounds of this type, Chesnokov (1999) set forth the concept of the crystallochemical transition at extreme temperatures attaining 1200-1450°C in pyrogenic systems. First of all, intertype transitions (oxygen-bearing-oxygen-free) and interclass transitions (chloride-silicate, carbonate-sulfide, chlorideoxide) are realized. The specificity of pyrometamorphic mineral assemblages consists in the abundance of silicates with additional anions (F-, Cl-, (CO3)2-) (Sokol et al., 2005). Minerals of the ellestadite group Ca10(SiO4)3 - x (SO4)3 - x (PO4)2 x (OH,F,Cl)2 are a spectacular example of these features. In the general case, they are silicate-sulfate-phosphate-hydroxide-chlorides-fluorides. The detailed description of these minerals based on the study of the original collection of pyrometamorphic minerals is presented in this paper.

The Global Flows of Metals and Minerals

USGS Publications Warehouse

Rogich, Donald G.; Matos, Grecia R.

2008-01-01

This paper provides a preliminary review of the trends in worldwide metals and industrial minerals production and consumption based on newly developed global metals and minerals Material Flow Accounts (MFA). The MFA developed encompass data on extraction and consumption for 25 metal and mineral commodities, on a country-by-country and year-by-year basis, for the period 1970 to 2004. The data-base, jointly developed by the authors, resides with the U.S. Geological Survey (USGS) as individual commodity Excel workbooks and within a Filemaker data management system for use in analysis. Numerous national MFA have been developed to provide information on the industrial metabolism of individual countries. These MFA include material flows associated with the four commodity categories of goods that are inputs to a country's economy, agriculture, forestry, metals and minerals, and nonrenewable organic material. In some cases, the material flows associated with the creation and maintenance of the built infrastructure (such as houses, buildings, roads, airports, dams, and so forth) were also examined. The creation of global metals and industrial minerals flows is viewed as a first step in the creation of comprehensive global MFA documenting the historical and current flows of all of the four categories of physical goods that support world economies. Metals and minerals represent a major category of nonrenewable resources that humans extract from and return to the natural ecosystem. As human populations and economies have increased, metals and industrial minerals use has increased concomitantly. This dramatic growth in metals and minerals use has serious implications for both the availability of future resources and the health of the environment, which is affected by the outputs associated with their use. This paper provides an overview of a number of the trends observed by examining the database and suggests areas for future study.

30 CFR 254.22 - What information must I include in the “Introduction and plan contents” section?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What information must I include in the âIntroduction and plan contentsâ section? 254.22 Section 254.22 Mineral Resources MINERALS MANAGEMENT SERVICE... must I include in the “Introduction and plan contents” section? The “Introduction and plan contents...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 1 2014-04-01 2014-04-01 false Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 1 2012-04-01 2011-04-01 true Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 1 2013-04-01 2013-04-01 false Other minerals and deep-lying lead and zinc minerals. 215.25 Section 215.25 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead...

Minerals in our environment

USGS Publications Warehouse

Weathers, Judy; Galloway, John; Frank, Dave

2000-01-01

Minerals are found everywhere in our daily lives. This poster depicts numerous items found throughout a home, and the mineral(s) or mineral resources used in the ingredients of, or construction/manufacturing of those items. Designed for K-8 Teachers this poster can be scaled and is printable at 36" x 60" and legible at 11" x 17" in size.

Lead distribution in Permo-Carboniferous coal from the North China Plate, China.

PubMed

Kunli, Luo; Jidong, Lu; Lianwu, Chen

2005-02-01

The content and distribution of the lead in coal, gangue and the sulfur ball and the pyritic gangue of the Permo-Carboniferous in the North China Plate have been systematically studied (nearly 300 samples) in this paper. The Permo-Carboniferous coals in the North China Plate account for nearly 44.45% of total Chinese coal resources, and most of the steam coals in China come from the Permo-Carboniferous coals in the North China Plate. The result shows that lead content in the coal varied from 1.45 to 63.60 mg kg(-1), averaging 23.95 mg kg(-1); the lead content of the sulfur ball and the pyritic gangue in the coal seam ranges from 70.26-1060 mg kg(-1), with an average of 271.28 mg kg(-1); the lead content of the gangue is from 29.5 to 77.81 mg kg(-1), averaging at 40.77 mg kg(-1). The lead in the coal seam is mainly concentrated in the pyrite, such as sulfur ball, pyritic gangue or pyrite, and is the least concentrated in the organic of coal. The content of the lead has a direct ratio with the ash and the pyretic sulfur. Coal washing can reduce the content of the pyretic sulfur and the lead.

Mineral Physics Educational Modules for Advanced Undergraduates and Graduate Students

NASA Astrophysics Data System (ADS)

Burnley, P. C.; Thomas, S.; Honn, D. K.

2011-12-01

We are assembling a group of web-based educational modules for a course entitled "Introduction to Mineral Physics". Although the modules are designed to function as part of a full semester course, each module will also be able to stand alone. The modules are targeted at entry level graduate students and advanced undergraduate students. Learning outcomes for the course are being developed in consultation with educators throughout the mineral physics community. Potential users include mineral physicists teaching "bricks and mortar" graduate classes at their own institutions, mineral physicists teaching graduate classes in a distance education setting, mineralogy teachers interested in including supplementary material in their undergraduate mineralogy class, undergraduates doing independent study projects and graduate students and colleagues in other subdisciplines who wish to brush up on mineral physics topics. The modules reside on the Science Education Resource Center at Carleton College web site in the On the Cutting Edge - Teaching Mineralogy collection. Links to the materials will be posted on the Consortium for Materials Properties Research in Earth Sciences website. The modules will be piloted in a graduate level distance education course in mineral physics taught from UNLV during the spring 2012 semester. This course and others like it can address the current problems faced by faculty in state universities where rising minimum enrollments are making it difficult to teach a suitable graduate course to incoming students.

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Other minerals and deep-lying lead and zinc minerals. 215... LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead and zinc minerals. Except as provided in § 215.6(b), leases on Quapaw Indian lands, for mining...

25 CFR 215.25 - Other minerals and deep-lying lead and zinc minerals.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Other minerals and deep-lying lead and zinc minerals. 215... LEAD AND ZINC MINING OPERATIONS AND LEASES, QUAPAW AGENCY § 215.25 Other minerals and deep-lying lead and zinc minerals. Except as provided in § 215.6(b), leases on Quapaw Indian lands, for mining...

Defining reactive sites on hydrated mineral surfaces: Rhombohedral carbonate minerals

NASA Astrophysics Data System (ADS)

Villegas-Jiménez, Adrián; Mucci, Alfonso; Pokrovsky, Oleg S.; Schott, Jacques

2009-08-01

Despite the success of surface complexation models (SCMs) to interpret the adsorptive properties of mineral surfaces, their construct is sometimes incompatible with fundamental chemical and/or physical constraints, and thus, casts doubts on the physical-chemical significance of the derived model parameters. In this paper, we address the definition of primary surface sites (i.e., adsorption units) at hydrated carbonate mineral surfaces and discuss its implications to the formulation and calibration of surface equilibria for these minerals. Given the abundance of experimental and theoretical information on the structural properties of the hydrated (10.4) cleavage calcite surface, this mineral was chosen for a detailed theoretical analysis of critical issues relevant to the definition of primary surface sites. Accordingly, a single, generic charge-neutral surface site ( tbnd CaCO 3·H 2O 0) is defined for this mineral whereupon mass-action expressions describing adsorption equilibria were formulated. The one-site scheme, analogous to previously postulated descriptions of metal oxide surfaces, allows for a simple, yet realistic, molecular representation of surface reactions and provides a generalized reference state suitable for the calculation of sorption equilibria for rhombohedral carbonate minerals via Law of Mass Action (LMA) and Gibbs Energy Minimization (GEM) approaches. The one-site scheme is extended to other rhombohedral carbonate minerals and tested against published experimental data for magnesite and dolomite in aqueous solutions. A simplified SCM based on this scheme can successfully reproduce surface charge, reasonably simulate the electrokinetic behavior of these minerals, and predict surface speciation agreeing with available spectroscopic data. According to this model, a truly amphoteric behavior is displayed by these surfaces across the pH scale but at circum-neutral pH (5.8-8.2) and relatively high ΣCO 2 (⩾1 mM), proton/bicarbonate co

Reagan issues mineral policy

NASA Astrophysics Data System (ADS)

The National Materials and Minerals Program plan and report that President Reagan sent to Congress on April 5 aims to ‘decrease America's minerals vulnerability’ while reducing future dependence on potentially unstable foreign sources of minerals. These goals would be accomplished by taking inventory of federal lands to determine mineral potential; by meeting the stockpile goals set by the Strategic and Critical Material Stockpiling Act; and by establishing a business and political climate that would encourage private-sector research and development on minerals.Now that the Administration has issued its plan, the Subcommittee on Mines and Mining of the House Committee on Interior and Insular Affairs will consider the National Minerals Security Act (NMSA), which was introduced 1 year ago by subcommittee chairman Jim Santini (D-Nev.) [Eos, May 19, 1981, p. 497]. The bill calls for establishing a three-member White-House-level council to coordinate the development of a national minerals policy; amending tax laws to assist the mining industry to make capital investments to locate and produce strategic materials; and creating a revolving fund for the sale and purchase of strategic minerals. In addition, the NMSA bill would allow the secretary of the interior to make previously withdrawn public lands available for mineral development. The subcommittee will hold a hearing on the Administration's plan on May 11. Interior Secretary James Watt has been invited to testify.

United States mineral resources

USGS Publications Warehouse

Brobst, Donald A.; Pratt, Walden P.

1973-01-01

650 of the U.S. Bureau of Mines) ; indeed, we regard that book and the present volume as being complementary. In the examination of the geologic possibilities for finding new deposits-in many respects the principal innovative contributions of this volume-we asked the authors to frankly apply the limits of their ingenuity and not only to summarize current theories but also to express their own intuitive ideas, however speculative and unconventional they may seem, that have come from years of study devoted to the origin of mineral deposits. Readers will see that some authors have speculated more courageously than others. In any case, we believe readers will find all the chapters interesting, and many stimulating; and a few we believe can be frankly characterized as intellectually exciting. Most chapters include a section on prospecting techniques, and a summary of geologic or related problems on which the authors believe research might be most fruitful in the continuing efforts to find new resources. An integral part of the book is the bibliographic material cited at the conclusion of each chapter, in lieu of repetition of detailed descriptions already in print. Index and "spot" maps are not included in most chapters because they are available elsewhere, and in many cases with more detail than could possibly be included here. Maps showing the distribution of known deposits of many commodities in the United States are available in the Mineral Resource (MR) map series of the U.S. Geological Survey and in the National Atlas of the United States. The first three chapters deal not with resources of specific commodities but with general information that is pertinent to the study of mineral resources. In the introductory chapter we discuss the purposes of the book, the distinctions between reserves and various categories of resources, and some general conclusions drawn from our view of the book in its entirety. In the second chapter V. E. McKelvey discusses the problems of

Magnetic susceptibilities of minerals

USGS Publications Warehouse

Rosenblum, Sam; Brownfield, I.K.

2000-01-01

Magnetic separation of minerals is a topic that is seldom reported in the literature for two reasons. First, separation data generally are byproducts of other projects; and second, this study requires a large amount of patience and is unusually tedious. Indeed, we suspect that most minerals probably are never investigated for this property. These data are timesaving for mineralogists who concentrate mono-mineralic fractions for chemical analysis, age dating, and for other purposes. The data can certainly be used in the ore-beneficiation industries. In some instances, magnetic-susceptibility data may help in mineral identification, where other information is insufficient. In past studies of magnetic separation of minerals, (Gaudin and Spedden, 1943; Tille and Kirkpatrick, 1956; Rosenblum, 1958; Rubinstein and others, 1958; Flinter, 1959; Hess, 1959; Baker, 1962; Meric and Peyre, 1963; Rojas and others, 1965; and Duchesne, 1966), the emphasis has been on the ferromagnetic and paramagnetic ranges of extraction. For readers interested in the history of magnetic separation of minerals, Krumbein and Pettijohn (1938, p. 344-346) indicated nine references back to 1848. The primary purpose of this paper is to report the magnetic-susceptibility data on as many minerals as possible, similar to tables of hardness, specific gravity, refractive indices, and other basic physical properties of minerals. A secondary purpose is to demonstrate that the total and best extraction ranges are influenced by the chemistry of the minerals. The following notes are offered to help avoid problems in separating a desired mineral concentrate from mixtures of mineral grains.

New Minerals and Science.

ERIC Educational Resources Information Center

Birch, William D.

1997-01-01

Defines geodiversity, compares it to biodiversity, and discusses the mineral classification system. Charts the discovery of new minerals in Australia over time and focuses on uses of these minerals in technological advances. (DDR)

Sulphurous Mineral Waters: New Applications for Health

PubMed Central

Carbajo, Jose Manuel

2017-01-01

Sulphurous mineral waters have been traditionally used in medical hydrology as treatment for skin, respiratory, and musculoskeletal disorders. However, driven by recent intense research efforts, topical treatments are starting to show benefits for pulmonary hypertension, arterial hypertension, atherosclerosis, ischemia-reperfusion injury, heart failure, peptic ulcer, and acute and chronic inflammatory diseases. The beneficial effects of sulphurous mineral waters, sulphurous mud, or peloids made from sulphurous mineral water have been attributed to the presence of sulphur mainly in the form of hydrogen sulphide. This form is largely available in conditions of low pH when oxygen concentrations are also low. In the organism, small amounts of hydrogen sulphide are produced by some cells where they have numerous biological signalling functions. While high levels of hydrogen sulphide are extremely toxic, enzymes in the body are capable of detoxifying it by oxidation to harmless sulphate. Hence, low levels of hydrogen sulphide may be tolerated indefinitely. In this paper, we review the chemistry and actions of hydrogen sulphide in sulphurous mineral waters and its natural role in body physiology. This is followed by an update of available data on the impacts of exogenous hydrogen sulphide on the skin and internal cells and organs including new therapeutic possibilities of sulphurous mineral waters and their peloids. PMID:28484507

Probability calculations for three-part mineral resource assessments

USGS Publications Warehouse

Ellefsen, Karl J.

2017-06-27

Three-part mineral resource assessment is a methodology for predicting, in a specified geographic region, both the number of undiscovered mineral deposits and the amount of mineral resources in those deposits. These predictions are based on probability calculations that are performed with computer software that is newly implemented. Compared to the previous implementation, the new implementation includes new features for the probability calculations themselves and for checks of those calculations. The development of the new implementation lead to a new understanding of the probability calculations, namely the assumptions inherent in the probability calculations. Several assumptions strongly affect the mineral resource predictions, so it is crucial that they are checked during an assessment. The evaluation of the new implementation leads to new findings about the probability calculations,namely findings regarding the precision of the computations,the computation time, and the sensitivity of the calculation results to the input.

Mineral transformations during the dissolution of uranium ore minerals by dissimilatory metal-reducing bacteria

NASA Astrophysics Data System (ADS)

Glasauer, S.; Weidler, P.; Fakra, S.; Tyliszczak, T.; Shuh, D.

2011-12-01

Carnotite minerals [X2(UO2)2(VO4)2]; X = K, Ca, Ba, Mn, Na, Cu or Pb] form the major ore of uranium in the Colorado Plateau. These deposits are highly oxidized and contain U(VI) and V(IV). The biotransformation of U(VI) bound in carnotite by bacteria during dissimilatory metal reduction presents a complex puzzle in mineral chemistry. Both U(VI) and V(V) can be respired by metal reducing bacteria, and the mineral structure can change depending on the associated counterion. We incubated anaerobic cultures of S. putrefaciens CN32 with natural carnotite minerals from southeastern Utah in a nutrient-limited defined medium. Strain CN32 is a gram negative bacterium and a terrestrial isolate from New Mexico. The mineral and metal transformations were compared to a system that contained similar concentrations of soluble U(VI) and V(V). Electron (SEM, TEM) microscopies and x-ray spectromicroscopy (STXM) were used in conjunction with XRD to track mineral changes, and bacterial survival was monitored throughout the incubations. Slow rates of metal reduction over 10 months for the treatment with carnotite minerals revealed distinct biotic and abiotic processes, providing insight on mineral transformation and bacteria-metal interactions. The bacteria existed as small flocs or individual cells attached to the mineral phase, but did not adsorb soluble U or V, and accumulated very little of the biominerals. Reduction of mineral V(V) necessarily led to a dismantling of the carnotite structure. Bioreduction of V(V) by CN32 contributed small but profound changes to the mineral system, resulting in new minerals. Abiotic cation exchange within the carnotite group minerals induced the rearrangement of the mineral structures, leading to further mineral transformation. In contrast, bacteria survival was poor for treatments with soluble U(VI) and V(V), although both metals were reduced completely and formed solid UO2 and VO2; we also detected V(III). For these treatments, the bacteria

Characterization of iron and manganese minerals and their associated microbiota in different mine sites to reveal the potential interactions of microbiota with mineral formation.

PubMed

Park, Jin Hee; Kim, Bong-Soo; Chon, Chul-Min

2018-01-01

Different environmental conditions such as pH and dissolved elements of mine stream induce precipitation of different minerals and their associated microbial community may vary. Therefore, mine precipitates from various environmental conditions were collected and their associated microbiota were analyzed through metagenomic DNA sequencing. Various Fe and Mn minerals including ferrihydrite, schwertmannite, goethite, birnessite, and Mn-substituted δ-FeOOH (δ-(Fe 1-x , Mn x )OOH) were found in the different environmental conditions. The Fe and Mn minerals were enriched with toxic metal(loid)s including As, Cd, Ni and Zn, indicating they can act as scavengers of toxic metal(loid)s in mine streams. Under acidic conditions, Acidobacteria was dominant phylum and Gallionella (Fe oxidizing bacteria) was the predominant genus in these Fe rich environments. Manganese oxidizing bacteria, Hyphomicrobium, was found in birnessite forming environments. Leptolyngbya within Cyanobacteria was found in Fe and Mn oxidizing environments, and might contribute to Fe and Mn oxidation through the production of molecular oxygen. The potential interaction of microbial community with minerals in mine sites can be traced by analysis of microbial community in different Fe and Mn mineral forming environments. Iron and Mn minerals contribute to the removal of toxic metal(loid)s from mine water. Therefore, the understanding characteristics of mine precipitates and their associated microbes helps to develop strategies for the management of contaminated mine water. Copyright © 2017 Elsevier Ltd. All rights reserved.

A process for reducing rocks and concentrating heavy minerals

USGS Publications Warehouse

Strong, Thomas R.; Driscoll, Rhonda L.

2016-03-30

Once the rock is reduced to grains, it is necessary to separate the grains into paramagnetic and nonparamagnetic and heavy and light mineral fractions. In separating grains by property, those minerals chemically suited for radiometric dating are abundantly concentrated. Grams of mineralogical material can then be analyzed and characterized by multiple methods including trace element chemistry, laser ablation, and in particular, ion geochronology.

Recent Developments in Multivitamin/Mineral Research12

PubMed Central

Comerford, Kevin B.

2013-01-01

The 2010 Dietary Guidelines Advisory Committee was charged with the task of investigating the effects of multivitamin/mineral supplements on healthy populations and also on those with chronic disease. The evidence from which the committee prepared its conclusions was graded on 5 fundamental criteria: quality, consistency, quantity, clinical impact, and generalizability. The committee concluded that for the general healthy population, evidence was insufficient to make a multivitamin/mineral recommendation. On the other hand, the committee noted the value of some supplemental nutrients for at-risk populations such as iron, folic acid, and vitamin B-12. However, most of the studies referenced for the research used the conventional, all-encompassing, and oversimplified definition of a multivitamin/mineral as being a supplement containing 3 or more vitamins with or without minerals. In the few years since the committee released its 2010 report, several randomized clinical trials showing the benefits of daily multivitamin/mineral supplementation have been completed using supplements containing at least 10 or more vitamins and/or minerals, but there also continues to be some reports that do not find benefit from such supplements. Furthermore, several steps have been taken to advance the science behind these supplements so that consumers, physicians, and government agencies can all have more confidence in understanding the role of supplemental nutrition in the American diet. This review provides new evidence from 2010 onward addressing the committee’s primary concerns about multivitamin/mineral research in regard to improving public health. It also includes several recent studies that may be of interest to future committees indicating the potential benefits of these supplements on improving the cognitive performance and mental well-being of healthy populations. PMID:24228193

75 FR 80947 - Conflict Minerals

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-23

... require any issuer for which conflict minerals are necessary to the functionality or production of a... measures would include, but would not be limited to, an independent private sector audit of the issuer's... obtained an independent private sector audit of its report, provide the audit report, and make its reports...

30 CFR 285.908 - What must I include in my decommissioning notice?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What must I include in my decommissioning notice? 285.908 Section 285.908 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND... the impacts previously identified and evaluated; (2) Require any additional Federal permits; or (3...

Preparation and Characteristics of Porous Ceramics by a foaming Technology at Low Temperature

NASA Astrophysics Data System (ADS)

Zhang, H. Q.; Wang, S. P.; Wen, J.; Wu, N.; Xu, S. H.

2017-12-01

Recycling and converting coal gangue and red mud into porous ceramics with good performance is a feasible disposal route. In this present work, porous foam ceramics was prepared using coal gangue and red mud as main raw materials at low sintering temperature, The amount of coal gangue and red mud were up to 70 wt%. To regulate the forming and sintering performance of the product, quartz sands and clay material were added to the formula. The green body was formed by a foaming technology using aluminum powders as foaming agents at room temperature. After foamed, the specimens were dried at 60-80 °C, and then calcined at 1060°C. Effects of concentration of NaOH and amount of aluminum powders on the phase, mechanical properties and microstructure were investigated here. Such study is expected to provide a new utilization route of the coal gangue and red mud, and brings both intensive environmental and economic benefits.

Dietary Supplements and Health Aids: A Critical Evaluation, Part 1- Vitamins and Minerals.

ERIC Educational Resources Information Center

Dubick, Michael A.; Rucker, Robert B.

1983-01-01

Evaluates vitamins/minerals, distinguishing whether studies cited used animal or human subjects. Vitamins discussed include niacin and vitamins B-12, C, A, D, E, and megavitamin supplementation (intake of vitamins at levels 10 times the recommended daily allowance). Minerals considered include dolomite/bone meal, chromium (glucose tolerance…

Bone mineral measurement using dual energy x ray densitometry

NASA Technical Reports Server (NTRS)

Smith, Steven W.

1989-01-01

Bone mineral measurements before and after space missions have shown that weightlessness greatly accelerates bone demineralization. Bone mineral losses as high as 1 to 3 percent per month were reported. Highly precise instrumentation is required to monitor this loss and thereby test the efficacy of treatment. During the last year, a significant improvement was made in Dual-Photon Absorptiometry by replacing the radioactive source with an x ray tube. Advantages of this system include: better precision, lower patient dose, better spacial resolution, and shorter scan times. The high precision and low radiation dose of this technique will allow detection of bone mineral changes of less than 1 percent with measurements conducted directly at the sites of interest. This will allow the required bone mineral studies to be completed in a shorter time with greater confidence.

Bioleaching of serpentine group mineral by fungus Talaromyces flavus: application for mineral carbonation

NASA Astrophysics Data System (ADS)

Li, Z.; Lianwen, L.; Zhao, L.; Teng, H.

2011-12-01

Many studies of serpentine group mineral dissolution for mineral carbonation have been published in recent years. However, most of them focus mainly on either physical and chemical processes or on bacterial function, rather than fungal involvement in the bioleaching of serpentine group mineral. Due to the excessive costs of the magnesium dissolution process, finding a lower energy consumption method will be meaningful. A fungal strain Talaromyces flavus was isolated from serpentinic rock of Donghai (China). No study of its bioleaching ability is currently available. It is thus of great significance to explore the impact of T. flavus on the dissolution of serpentine group mineral. Serpentine rock-inhabiting fungi belonging to Acremonium, Alternaria, Aspergillus, Botryotinia, Cladosporium, Clavicipitaceae, Cosmospora, Fusarium, Monascus, Paecilomyces, Penicillium, Talaromyces, Trichoderma were isolated. These strains were chosen on the basis of resistance to magnesium and nickel characterized in terms of minimum inhibiting concentration (MIC). Specifically, the strain Talaromyces flavus has a high tolerance to both magnesium (1 mol/L) and nickel (10 mM/L), and we examine its bioleaching ability on serpentine group mineral. Contact and separation experiments (cut-off 8 000-14 000 Da), as well as three control experiments, were set up for 30 days. At least three repeated tests were performed for each individual experiment. The results of our experiments demonstrate that the bioleaching ability of T. flavus towards serpentine group mineral is evident. 39.39 wt% of magnesium was extracted from lizardite during the bioleaching period in the contact experiment, which showed a dissolution rate at about a constant 0.126 mM/d before reaching equilibrium in 13 days. The amount of solubilized Mg from chrysotile and antigorite were respectively 37.79 wt% and 29.78 wt% in the contact experiment. These results make clear the influence of mineral structure on mineral bioleaching

The three-dimensional distribution of minerals in potato tubers

PubMed Central

Subramanian, Nithya K.; White, Philip J.; Broadley, Martin R.; Ramsay, Gavin

2011-01-01

Background and Aims The three-dimensional distributions of mineral elements in potato tubers provide insight into their mechanisms of transport and deposition. Many of these minerals are essential to a healthy human diet, and characterizing their distribution within the potato tuber will guide the effective utilization of this staple foodstuff. Methods The variation in mineral composition within the tuber was determined in three dimensions, after determining the orientation of the harvested tuber in the soil. The freeze-dried tuber samples were analysed for minerals using inductively coupled plasma-mass spectrometry (ICP-MS). Minerals measured included those of nutritional significance to the plant and to human consumers, such as iron, zinc, copper, calcium, magnesium, manganese, phosphorus, potassium and sulphur. Key Results The concentrations of most minerals were higher in the skin than in the flesh of tubers. The potato skin contained about 17 % of total tuber zinc, 34 % of calcium and 55 % of iron. On a fresh weight basis, most minerals were higher in tuber flesh at the stem end than the bud end of the tuber. Potassium, however, displayed a gradient in the opposite direction. The concentrations of phosphorus, copper and calcium decreased from the periphery towards the centre of the tuber. Conclusions The distribution of minerals varies greatly within the potato tuber. Low concentrations of some minerals relative to those in leaves may be due to their low mobility in phloem, whereas high concentrations in the skin may reflect direct uptake from the soil across the periderm. In tuber flesh, different minerals show distinct patterns of distribution in the tuber, several being consistent with phloem unloading in the tuber and limited onward movement. These findings have implications both for understanding directed transport of minerals in plants to stem-derived storage organs and for the dietary implications of different food preparation methods for potato tubers

43 CFR 3471.2-1 - Disposal of land with a reservation of minerals.

Code of Federal Regulations, 2013 CFR

2013-10-01

... minerals. 3471.2-1 Section 3471.2-1 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) COAL MANAGEMENT... reservation of minerals. (a) Where the lands included in a lease or license to mine have been or may be...

43 CFR 3471.2-1 - Disposal of land with a reservation of minerals.

Code of Federal Regulations, 2011 CFR

2011-10-01

... minerals. 3471.2-1 Section 3471.2-1 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) COAL MANAGEMENT... reservation of minerals. (a) Where the lands included in a lease or license to mine have been or may be...

43 CFR 3471.2-1 - Disposal of land with a reservation of minerals.

Code of Federal Regulations, 2014 CFR

2014-10-01

... minerals. 3471.2-1 Section 3471.2-1 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) COAL MANAGEMENT... reservation of minerals. (a) Where the lands included in a lease or license to mine have been or may be...

Effect of soil metal contamination on glyphosate mineralization: role of zinc in the mineralization rates of two copper-spiked mineral soils.

PubMed

Kim, Bojeong; Kim, Young Sik; Kim, Bo Min; Hay, Anthony G; McBride, Murray B

2011-03-01

A systematic investigation into lowered degradation rates of glyphosate in metal-contaminated soils was performed by measuring mineralization of [(14)C]glyphosate to (14)CO(2) in two mineral soils that had been spiked with Cu and/or Zn at various loadings. Cumulative (14)CO(2) release was estimated to be approximately 6% or less of the amount of [(14)C]glyphosate originally added in both soils over an 80-d incubation. For all but the highest Cu treatments (400 mg kg(-1)) in the coarse-textured Arkport soil, mineralization began without a lag phase and declined over time. No inhibition of mineralization was observed for Zn up to 400 mg kg(-1) in either soil, suggesting differential sensitivity of glyphosate mineralization to the types of metal and soil. Interestingly, Zn appeared to alleviate high-Cu inhibition of mineralization in the Arkport soil. The protective role of Zn against Cu toxicity was also observed in the pure culture study with Pseudomonas aeruginosa, suggesting that increased mineralization rates in high Cu soil with Zn additions might have been due to alleviation of cellular toxicity by Zn rather than a mineralization specific mechanism. Extensive use of glyphosate combined with its reduced degradation in Cu-contaminated, coarse-textured soils may increase glyphosate persistence in soil and consequently facilitate Cu and glyphosate mobilization in the soil environment. Copyright © 2010 SETAC.

30 CFR 585.908 - What must I include in my decommissioning notice?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false What must I include in my decommissioning notice? 585.908 Section 585.908 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, DEPARTMENT OF THE... determines that your decommissioning activities would: (1) Result in a significant change in the impacts...

30 CFR 250.1902 - What must I include in my SEMS program?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 2 2011-07-01 2011-07-01 false What must I include in my SEMS program? 250.1902 Section 250.1902 Mineral Resources BUREAU OF OCEAN ENERGY MANAGEMENT, REGULATION, AND ENFORCEMENT... § 250.1915) (8) Mechanical Integrity (Assurance of Quality and Mechanical Integrity of Critical...

A facile in vitro model to study rapid mineralization in bone tissues.

PubMed

Deegan, Anthony J; Aydin, Halil M; Hu, Bin; Konduru, Sandeep; Kuiper, Jan Herman; Yang, Ying

2014-09-16

Mineralization in bone tissue involves stepwise cell-cell and cell-ECM interaction. Regulation of osteoblast culture microenvironments can tailor osteoblast proliferation and mineralization rate, and the quality and/or quantity of the final calcified tissue. An in vitro model to investigate the influencing factors is highly required. We developed a facile in vitro model in which an osteoblast cell line and aggregate culture (through the modification of culture well surfaces) were used to mimic intramembranous bone mineralization. The effect of culture environments including culture duration (up to 72 hours for rapid mineralization study) and aggregates size (monolayer culture as control) on mineralization rate and mineral quantity/quality were examined by osteogenic gene expression (PCR) and mineral markers (histological staining, SEM-EDX and micro-CT). Two size aggregates (on average, large aggregates were 745 μm and small 79 μm) were obtained by the facile technique with high yield. Cells in aggregate culture generated visible and quantifiable mineralized matrix within 24 hours, whereas cells in monolayer failed to do so by 72 hours. The gene expression of important ECM molecules for bone formation including collagen type I, alkaline phosphatase, osteopontin and osteocalcin, varied temporally, differed between monolayer and aggregate cultures, and depended on aggregate size. Monolayer specimens stayed in a proliferation phase for the first 24 hours, and remained in matrix synthesis up to 72 hours; whereas the small aggregates were in the maturation phase for the first 24 and 48 hour cultures and then jumped to a mineralization phase at 72 hours. Large aggregates were in a mineralization phase at all these three time points and produced 36% larger bone nodules with a higher calcium content than those in the small aggregates after just 72 hours in culture. This study confirms that aggregate culture is sufficient to induce rapid mineralization and that aggregate

Application of Polychromatic µCT for Mineral Density Determination

PubMed Central

Zou, W.; Hunter, N.; Swain, M.V.

2011-01-01

Accurate assessment of mineral density (MD) provides information critical to the understanding of mineralization processes of calcified tissues, including bones and teeth. High-resolution three-dimensional assessment of the MD of teeth has been demonstrated by relatively inaccessible synchrotron radiation microcomputed tomography (SRµCT). While conventional desktop µCT (CµCT) technology is widely available, polychromatic source and cone-shaped beam geometry confound MD assessment. Recently, considerable attention has been given to optimizing quantitative data from CµCT systems with polychromatic x-ray sources. In this review, we focus on the approaches that minimize inaccuracies arising from beam hardening, in particular, beam filtration during the scan, beam-hardening correction during reconstruction, and mineral density calibration. Filtration along with lowest possible source voltage results in a narrow and near-single-peak spectrum, favoring high contrast and minimal beam-hardening artifacts. More effective beam monochromatization approaches are described. We also examine the significance of beam-hardening correction in determining the accuracy of mineral density estimation. In addition, standards for the calibration of reconstructed grey-scale attenuation values against MD, including K2PHO4 liquid phantom, and polymer-hydroxyapatite (HA) and solid hydroxyapatite (HA) phantoms, are discussed. PMID:20858779

Mineral sources and transport pathways for arsenic release in a coastal watershed, USA

USGS Publications Warehouse

Foley, Nora K.; Ayuso, Robert A.

2008-01-01

Metasedimentary bedrock of coastal Maine contains a diverse suite of As-bearing minerals that act as significant sources of elements found in ground and surface waters in the region. Arsenic sources in the Penobscot Formation include, in order of decreasing As content by weight: löllingite and realgar (c.70%), arsenopyrite, cobaltite, glaucodot, and gersdorffite (in the range of 34–45%), arsenian pyrite (<4%), and pyrrhotite (<0.15%). In the Penobscot Formation, the relative stability of primary As-bearing minerals follows a pattern where the most commonly observed highly altered minerals are pyrrhotite, realgar, niccolite, löllingite > glaucodot, arsenopyrite-cobaltian > arsenopyrite, cobaltite, gersdorffite, fine-grained pyrite, Ni-pyrite > coarse-grained pyrite. Reactions illustrate that oxidation of Fe-As disulphide group and As-sulphide minerals is the primary release process for As. Liberation of As by carbonation of realgar and orpiment in contact with high-pH groundwaters may contribute locally to elevated contents of As in groundwater, especially where As is decoupled from Fe. Released metals are sequestered in secondary minerals by sorption or by incorporation in crystal structures. Secondary minerals acting as intermediate As reservoirs include claudetite (c.75%), orpiment (61%), scorodite (c. 45%), secondary arsenopyrite (c. 46%), goethite (<4490 ppm), natrojarosite (<42 ppm), rosenite, melanterite, ferrihydrite, and Mn-hydroxide coatings. Some soils also contain Fe-Co-Ni-arsenate, Ca-arsenate, and carbonate minerals. Reductive dissolution of Fe-oxide minerals may govern the ultimate release of iron and arsenic – especially As(V) – to groundwater; however, dissolution of claudetite (arsenic trioxide) may directly contribute As(III). Processes thought to explain the release of As from minerals in bedrock include oxidation of arsenian pyrite or arsenopyrite, or carbonation of As-sulphides, and most models based on these generally rely on

Microcoulometric measurement of water in minerals

USGS Publications Warehouse

Cremer, M.; Elsheimer, H.N.; Escher, E.E.

1972-01-01

A DuPont Moisture Analyzer is used in a microcoulometric method for determining water in minerals. Certain modifications, which include the heating of the sample outside the instrument, protect the system from acid gases and insure the conversion of all hydrogen to water vapor. Moisture analyzer data are compared to concurrent data obtained by a modified Penfield method. In general, there is a positive bias of from 0.1 to 0.2% in the moisture analyzer results and a similarity of bias in minerals of the same kind. Inhomogeneity, sample size, and moisture pick-up are invoked to explain deviations. The method is particularly applicable to small samples. ?? 1972.

Impact-Induced Clay Mineral Formation and Distribution on Mars

NASA Technical Reports Server (NTRS)

Rivera-Valentin, E. G.; Craig, P. I.

2015-01-01

Clay minerals have been identified in the central peaks and ejecta blankets of impact craters on Mars. Several studies have suggested these clay minerals formed as a result of impact induced hydrothermalism either during Mars' Noachian era or more recently by the melting of subsurface ice. Examples of post-impact clay formation is found in several locations on Earth such as the Mjolnir and Woodleigh Impact Structures. Additionally, a recent study has suggested the clay minerals observed on Ceres are the result of impact-induced hydrothermal processes. Such processes may have occurred on Mars, possibly during the Noachian. Distinguishing between clay minerals formed preor post-impact can be accomplished by studying their IR spectra. In fact, showed that the IR spectra of clay minerals is greatly affected at longer wavelengths (i.e. mid-IR, 5-25 micron) by impact-induced shock deformation while the near-IR spectra (1.0-2.5 micron) remains relatively unchanged. This explains the discrepancy between NIR and MIR observations of clay minerals in martian impact craters noted. Thus, it allows us to determine whether a clay mineral formed from impact-induced hydrothermalism or were pre-existing and were altered by the impact. Here we study the role of impacts on the formation and distribution of clay minerals on Mars via a fully 3-D Monte Carlo cratering model, including impact- melt production using results from modern hydrocode simulations. We identify regions that are conducive to clay formation and the location of clay minerals post-bombardment.

Calcium phosphate mineralization is widely applied in crustacean mandibles.

PubMed

Bentov, Shmuel; Aflalo, Eliahu D; Tynyakov, Jenny; Glazer, Lilah; Sagi, Amir

2016-02-24

Crustaceans, like most mineralized invertebrates, adopted calcium carbonate mineralization for bulk skeleton reinforcement. Here, we show that a major part of the crustacean class Malacostraca (which includes lobsters, crayfishes, prawns and shrimps) shifted toward the formation of calcium phosphate as the main mineral at specified locations of the mandibular teeth. In these structures, calcium phosphate is not merely co-precipitated with the bulk calcium carbonate but rather creates specialized structures in which a layer of calcium phosphate, frequently in the form of crystalline fluorapatite, is mounted over a calcareous "jaw". From a functional perspective, the co-existence of carbonate and phosphate mineralization demonstrates a biomineralization system that provides a versatile route to control the physico-chemical properties of skeletal elements. This system enables the deposition of amorphous calcium carbonate, amorphous calcium phosphate, calcite and apatite at various skeletal locations, as well as combinations of these minerals, to form graded composites materials. This study demonstrates the widespread occurrence of the dual mineralization strategy in the Malacostraca, suggesting that in terms of evolution, this feature of phosphatic teeth did not evolve independently in the different groups but rather represents an early common trait.

Calcium phosphate mineralization is widely applied in crustacean mandibles

PubMed Central

Bentov, Shmuel; Aflalo, Eliahu D.; Tynyakov, Jenny; Glazer, Lilah; Sagi, Amir

2016-01-01

Crustaceans, like most mineralized invertebrates, adopted calcium carbonate mineralization for bulk skeleton reinforcement. Here, we show that a major part of the crustacean class Malacostraca (which includes lobsters, crayfishes, prawns and shrimps) shifted toward the formation of calcium phosphate as the main mineral at specified locations of the mandibular teeth. In these structures, calcium phosphate is not merely co-precipitated with the bulk calcium carbonate but rather creates specialized structures in which a layer of calcium phosphate, frequently in the form of crystalline fluorapatite, is mounted over a calcareous “jaw”. From a functional perspective, the co-existence of carbonate and phosphate mineralization demonstrates a biomineralization system that provides a versatile route to control the physico-chemical properties of skeletal elements. This system enables the deposition of amorphous calcium carbonate, amorphous calcium phosphate, calcite and apatite at various skeletal locations, as well as combinations of these minerals, to form graded composites materials. This study demonstrates the widespread occurrence of the dual mineralization strategy in the Malacostraca, suggesting that in terms of evolution, this feature of phosphatic teeth did not evolve independently in the different groups but rather represents an early common trait. PMID:26906263

Development of industrial minerals in Colorado

USGS Publications Warehouse

Arbogast, Belinda F.; Knepper, Daniel H.; Langer, William H.; Cappa, James A.; Keller, John W.; Widmann, Beth L.; Ellefsen, Karl J.; Klein, Terry L.; Lucius, Jeffrey E.; Dersch, John S.

2011-01-01

Technology and engineering have helped make mining safer and cleaner for both humans and the environment. Inevitably, mineral development entails costs as well as benefits. Developing a mine is an environmental, engineering, and planning challenge that must conform to many Federal, State, and local regulations. Community collaboration, creative design, and best management practices of sustainability and biodiversity can be positive indicators for the mining industry. A better understanding of aesthetics, culture, economics, geology, climate, vegetation and wildlife, topography, historical significance, and regional land planning is important in resolving land-use issues and managing mineral resources wisely. Ultimately, the consuming public makes choices about product use (including water, food, highways, housing, and thousands of other items) that influence operations of the mineral industry. Land planners, resource managers, earth scientists, designers, and public groups have a responsibility to consider sound scientific information, society's needs, and community appeals in making smart decisions concerning resource use and how complex landscapes should change. An effort to provide comprehensive geosciences data for land management agencies in central Colorado was undertaken in 2003 by scientists of the U.S. Geological Survey and the Colorado Geological Survey. This effort, the Central Colorado Assessment Project, addressed a variety of land-use issues: an understanding of the availability of industrial and metallic rocks and minerals, the geochemical and environmental effects of historic mining activity on surface water and groundwater, and the geologic controls on the availability and quality of groundwater. The USDA Forest Service and other land management agencies have the opportunity to contribute to the sustainable management of natural aggregate and other mineral resources through the identification and selective development of mineral resources and the

The mineral industry of Ethiopia: present conditions and future prospects

NASA Astrophysics Data System (ADS)

Assefa, Getaneh

Despite a record of mineral activity that dates back to Biblical times and the occurrence of a wide variety of minerals, as well as continuing efforts to discover major ore deposits, Ethiopia's mineral resources ahve remained of minor importance in the world economy. Mineral production in the last 20 years, for example, forms less than 1% of the estimated GDP. Well known minerals andmineral products available in the country in commercial quantities are: gold, platinum, manganese ore, natural agas, clays and clay products, feldspars, gypsum and anhydrite, slat, lime, limestone, cement, sand, structural and crushed stones, marble, mineral water and pumice. There are also vast reserves of water and geothermal power. Recently discovered deposits (over the last 20 years), with major reserves that may attain an important role in mineral production in the future, include potash salts, copper ore and diatomites. Minerals which are known to occur in Ethiopia, but of which supplies are deficient, or which have not yet been proved to exist in economic quantities are: nickel, iron, chromium, mineral fuels (oil, coal and uranium), sulphur, asbesttos, mica, talc, barytes, fluorites, borates, soda-ash, phosphates, wolframite, abrasives (garnet), molybdenite and vanadium. Within the last few years there has been an increasing appreciation of the economic significance of a mineral industry and a definite attempt to foster it. Mineral ownership is vested in the state are cotnrolled by the MInistry of Mines, Energy and Water Resources. The law relating to foreign investment in mines is liberal. The plans for the future have to provide for detailed and intensive exploration of the country's mineral resources, manufacture and fabrication.

Mineral Content Comparison at Two Gale Crater Sites

NASA Image and Video Library

2016-12-13

This graphic shows proportions of minerals identified in mudstone exposures at the "Yellowknife Bay" location where NASA's Curiosity Mars rover first analyzed bedrock, in 2013, and at the "Murray Buttes" area investigated in 2016. Minerals were identified by X-ray diffraction analysis of sample powder from the rocks. The samples were acquired by drilling and delivered to the Chemistry and Mineralogy (CheMin) instrument inside the rover. Two key differences in the Murray Buttes mudstone include hematite rather than magnetite, and far less abundance of crystalline mafic minerals, compared to the Yellowknife Bay mudstone composition. Hematite and magnetite are both iron oxide minerals, with hematite as a more oxidized one. That difference could result from the Murray Buttes mudstone layer experiencing more weathering than the Yellowknife Bay mudstone. More weathering could also account for the lower abundance of crystalline mafics, which are volcanic-origin minerals such as pyroxene and olivine. The Yellowknife Bay site is on the floor of Gale Crater. The Murray Buttes site is on lower Mount Sharp, the layered mound in the center of the crater. http://photojournal.jpl.nasa.gov/catalog/PIA21149

Health effects of mineral dusts, Volume 28: Proceedings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guthrie, G.D. Jr.; Mossman, B.T.

1993-12-31

The processes that lead to the development of disease (or pathogenesis) by minerals very likely occur at or near the mineral-fluid interface. Thus the field of ``mineral-induced pathogenesis`` is a prime candidate for interdisciplinary research, involving mineral scientists, health scientists, petrologists, pathologists, geochemists, biochemists, and surface scientists, to name a few. This review volume and the short course upon which it was based are intended to provide some of the necessary tools for the researcher interested in this area of interdisciplinary research. The chapters present several of the important problems, concepts, and approaches from both the geological and biological endsmore » of the spectrum. These two extremes are partially integrated throughout the book by cross-referencing between chapters. Chapter 1 also presents a general introduction into the ways in which these two areas overlap. The final chapter of this book discusses some of the regulatory aspects of minerals. A glossary is included at the end of this book, because the complexity of scientific terms in the two fields can thwart even the most enthusiastic of individuals. Individual reports have been processed separately for the database.« less

First Direct Detection of Clay Minerals on Mars

NASA Technical Reports Server (NTRS)

Singer, R. B.; Owensby, P. D.; Clark, R. N.

1985-01-01

Magnesian clays or clay-type minerals were conclusively detected in the martian regolith. Near-IR spectral observations of Mars using the Mauna Kea 2.2-m telescope show weak but definite absorption bands near microns. The absorption band positions and widths match those produced by combined OH stretch and Mg-OH lattice modes and are diagnostic of minerals with structural OH such as clays and amphiboles. Likely candidate minerals include serpentine, talc, hectorite, and sponite. There is no spectral evidence for aluminous hydroxylated minerals. No distinct band occurs at 2.55 microns, as would be expected if carbonates were responsible for the 2.35 micron absorption. High-albedo regions such as Elysium and Utopia have the strongest bands near 2.35 microns, as would be expected for heavily weathered soils. Low-albedo regions such as Iapygia show weaker but distinct bands, consistent with moderate coatings, streaks, and splotches of bright weathered material. In all areas observed, the 2.35-micron absorption is at least three times weaker than would be expected if well-crystallized clay minerals made up the bulk of bright soils on Mars.

Mineral Surface Rearrangement at High Temperatures: Implications for Extraterrestrial Mineral Grain Reactivity.

PubMed

King, Helen E; Plümper, Oliver; Putnis, Christine V; O'Neill, Hugh St C; Klemme, Stephan; Putnis, Andrew

2017-04-20

Mineral surfaces play a critical role in the solar nebula as a catalytic surface for chemical reactions and potentially acted as a source of water during Earth's accretion by the adsorption of water molecules to the surface of interplanetary dust particles. However, nothing is known about how mineral surfaces respond to short-lived thermal fluctuations that are below the melting temperature of the mineral. Here we show that mineral surfaces react and rearrange within minutes to changes in their local environment despite being far below their melting temperature. Polished surfaces of the rock and planetary dust-forming silicate mineral olivine ((Mg,Fe) 2 SiO 4 ) show significant surface reorganization textures upon rapid heating resulting in surface features up to 40 nm in height observed after annealing at 1200 °C. Thus, high-temperature fluctuations should provide new and highly reactive sites for chemical reactions on nebula mineral particles. Our results also may help to explain discrepancies between short and long diffusion profiles in experiments where diffusion length scales are of the order of 100 nm or less.

[Organic carbon and carbon mineralization characteristics in nature forestry soil].

PubMed

Yang, Tian; Dai, Wei; An, Xiao-Juan; Pang, Huan; Zou, Jian-Mei; Zhang, Rui

2014-03-01

Through field investigation and indoor analysis, the organic carbon content and organic carbon mineralization characteristics of six kinds of natural forest soil were studied, including the pine forests, evergreen broad-leaved forest, deciduous broad-leaved forest, mixed needle leaf and Korean pine and Chinese pine forest. The results showed that the organic carbon content in the forest soil showed trends of gradual decrease with the increase of soil depth; Double exponential equation fitted well with the organic carbon mineralization process in natural forest soil, accurately reflecting the mineralization reaction characteristics of the natural forest soil. Natural forest soil in each layer had the same mineralization reaction trend, but different intensity. Among them, the reaction intensity in the 0-10 cm soil of the Korean pine forest was the highest, and the intensities of mineralization reaction in its lower layers were also significantly higher than those in the same layers of other natural forest soil; comparison of soil mineralization characteristics of the deciduous broad-leaved forest and coniferous and broad-leaved mixed forest found that the differences of litter species had a relatively strong impact on the active organic carbon content in soil, leading to different characteristics of mineralization reaction.

The genesis of the newly discovered giant Wuben magmatic Fe-Ti oxide deposit in the Emeishan Large Igneous Province: a product of the late-stage redistribution and sorting of crystal slurries

NASA Astrophysics Data System (ADS)

Bai, Zhong-Jie; Zhong, Hong; Zhu, Wei-Guang; Hu, Wen-Jun; Chen, Cai-Jie

2018-04-01

A giant Fe-Ti oxide deposit hosted by the Wuben mafic intrusion has recently been discovered in the Pan-Xi area of the Emeishan Large Igneous Province (ELIP). The evolved compositions of the gangue minerals within the Fe-Ti oxide ores indicate that they formed during later stages of magma differentiation than those within the neighboring Panzhihua intrusion or other ore-bearing intrusions in this area. The rocks from the Wuben intrusion and MZb of the Panzhihua intrusion contain compositionally similar silicate minerals and have similar titanomagnetite/ilmenite ratios, suggesting that the former is related to and probably connected to the latter by subsurface magmatic conduits. This indicates that unconsolidated minerals that formed in the MZb flowed as crystal slurries into the Wuben magma chamber during the later stages of evolution of the parental magma. The later secondary enrichment of Fe-Ti oxides by mechanical redistribution and the sorting of crystals as a result of density and size differences generated the Wuben massive Fe-Ti oxide bodies. The ilmenite was commonly saturated in the magma at late stage of differentiation in the ELIP, thereby the associated deposit contains much higher contents of ilmenite. This indicates that future exploration for Fe-Ti oxide mineralization in the ELIP should not merely focus on the lower parts of large layered intrusions but should also include nearby relatively small intrusions or even the upper parts of large intrusions, especially as ilmenite-enriched Fe-Ti oxide deposits may have greater economic value than ilmenite-poor deposits.

Nanostructured Mineral Coatings Stabilize Proteins for Therapeutic Delivery.

PubMed

Yu, Xiaohua; Biedrzycki, Adam H; Khalil, Andrew S; Hess, Dalton; Umhoefer, Jennifer M; Markel, Mark D; Murphy, William L

2017-09-01

Proteins tend to lose their biological activity due to their fragile structural conformation during formulation, storage, and delivery. Thus, the inability to stabilize proteins in controlled-release systems represents a major obstacle in drug delivery. Here, a bone mineral inspired protein stabilization strategy is presented, which uses nanostructured mineral coatings on medical devices. Proteins bound within the nanostructured coatings demonstrate enhanced stability against extreme external stressors, including organic solvents, proteases, and ethylene oxide gas sterilization. The protein stabilization effect is attributed to the maintenance of protein conformational structure, which is closely related to the nanoscale feature sizes of the mineral coatings. Basic fibroblast growth factor (bFGF) released from a nanostructured mineral coating maintains its biological activity for weeks during release, while it maintains activity for less than 7 d during release from commonly used polymeric microspheres. Delivery of the growth factors bFGF and vascular endothelial growth factor using a mineral coated surgical suture significantly improves functional Achilles tendon healing in a rabbit model, resulting in increased vascularization, more mature collagen fiber organization, and a two fold improvement in mechanical properties. The findings of this study demonstrate that biomimetic interactions between proteins and nanostructured minerals provide a new, broadly applicable mechanism to stabilize proteins in the context of drug delivery and regenerative medicine. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

CO 2 Mineral Sequestration in Naturally Porous Basalt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiong, Wei; Wells, Rachel K.; Horner, Jake A.

2018-02-27

Continental flood basalts are extensive geologic features currently being evaluated as reservoirs that are suitable for long-term storage of carbon emissions. Favorable attributes of these formations for containment of injected carbon dioxide (CO2) include high mineral trapping capacity, unique structural features, and enormous volumes. We experimentally investigated mineral carbonation in whole core samples retrieved from the Grand Ronde basalt, the same formation into which ~1000 t of CO2 was recently injected in an eastern Washington pilot-scale demonstration. The rate and extent of carbonate mineral formation at 100 °C and 100 bar were tracked via time-resolved sampling of bench-scale experiments. Basaltmore » cores were recovered from the reactor after 6, 20, and 40 weeks, and three-dimensional X-ray tomographic imaging of these cores detected carbonate mineral formation in the fracture network within 20 weeks. Under these conditions, a carbon mineral trapping rate of 1.24 ± 0.52 kg of CO2/m3 of basalt per year was estimated, which is orders of magnitude faster than rates for deep sandstone reservoirs. On the basis of these calculations and under certain assumptions, available pore space within the Grand Ronde basalt formation would completely carbonate in ~40 years, resulting in solid mineral trapping of ~47 kg of CO2/m3 of basalt.« less

New Geophysical Technique for Mineral Exploration and Mineral Discrimination Based on Electromagnetic Methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michael S. Zhdanov

2005-03-09

The research during the first year of the project was focused on developing the foundations of a new geophysical technique for mineral exploration and mineral discrimination, based on electromagnetic (EM) methods. The proposed new technique is based on examining the spectral induced polarization effects in electromagnetic data using modern distributed acquisition systems and advanced methods of 3-D inversion. The analysis of IP phenomena is usually based on models with frequency dependent complex conductivity distribution. One of the most popular is the Cole-Cole relaxation model. In this progress report we have constructed and analyzed a different physical and mathematical model ofmore » the IP effect based on the effective-medium theory. We have developed a rigorous mathematical model of multi-phase conductive media, which can provide a quantitative tool for evaluation of the type of mineralization, using the conductivity relaxation model parameters. The parameters of the new conductivity relaxation model can be used for discrimination of the different types of rock formations, which is an important goal in mineral exploration. The solution of this problem requires development of an effective numerical method for EM forward modeling in 3-D inhomogeneous media. During the first year of the project we have developed a prototype 3-D IP modeling algorithm using the integral equation (IP) method. Our IE forward modeling code INTEM3DIP is based on the contraction IE method, which improves the convergence rate of the iterative solvers. This code can handle various types of sources and receivers to compute the effect of a complex resistivity model. We have tested the working version of the INTEM3DIP code for computer simulation of the IP data for several models including a southwest US porphyry model and a Kambalda-style nickel sulfide deposit. The numerical modeling study clearly demonstrates how the various complex resistivity models manifest differently in the

Metals, minerals and microbes: geomicrobiology and bioremediation.

PubMed

Gadd, Geoffrey Michael

2010-03-01

Microbes play key geoactive roles in the biosphere, particularly in the areas of element biotransformations and biogeochemical cycling, metal and mineral transformations, decomposition, bioweathering, and soil and sediment formation. All kinds of microbes, including prokaryotes and eukaryotes and their symbiotic associations with each other and 'higher organisms', can contribute actively to geological phenomena, and central to many such geomicrobial processes are transformations of metals and minerals. Microbes have a variety of properties that can effect changes in metal speciation, toxicity and mobility, as well as mineral formation or mineral dissolution or deterioration. Such mechanisms are important components of natural biogeochemical cycles for metals as well as associated elements in biomass, soil, rocks and minerals, e.g. sulfur and phosphorus, and metalloids, actinides and metal radionuclides. Apart from being important in natural biosphere processes, metal and mineral transformations can have beneficial or detrimental consequences in a human context. Bioremediation is the application of biological systems to the clean-up of organic and inorganic pollution, with bacteria and fungi being the most important organisms for reclamation, immobilization or detoxification of metallic and radionuclide pollutants. Some biominerals or metallic elements deposited by microbes have catalytic and other properties in nanoparticle, crystalline or colloidal forms, and these are relevant to the development of novel biomaterials for technological and antimicrobial purposes. On the negative side, metal and mineral transformations by microbes may result in spoilage and destruction of natural and synthetic materials, rock and mineral-based building materials (e.g. concrete), acid mine drainage and associated metal pollution, biocorrosion of metals, alloys and related substances, and adverse effects on radionuclide speciation, mobility and containment, all with immense social

Surface materials map of Afghanistan: iron-bearing minerals and other materials

USGS Publications Warehouse

King, Trude V.V.; Kokaly, Raymond F.; Hoefen, Todd M.; Dudek, Kathleen B.; Livo, Keith E.

2012-01-01

This map shows the distribution of selected iron-bearing minerals and other materials derived from analysis of HyMap imaging spectrometer data of Afghanistan. Using a NASA (National Aeronautics and Space Administration) WB-57 aircraft flown at an altitude of ~15,240 meters or ~50,000 feet, 218 flight lines of data were collected over Afghanistan between August 22 and October 2, 2007. The HyMap data were converted to apparent surface reflectance, then further empirically adjusted using ground-based reflectance measurements. The reflectance spectrum of each pixel of HyMap data was compared to the spectral features of reference entries in a spectral library of minerals, vegetation, water, ice, and snow. This map shows the spatial distribution of iron-bearing minerals and other materials having diagnostic absorptions at visible and near-infrared wavelengths. These absorptions result from electronic processes in the minerals. Several criteria, including (1) the reliability of detection and discrimination of minerals using the HyMap spectrometer data, (2) the relative abundance of minerals, and (3) the importance of particular minerals to studies of Afghanistan's natural resources, guided the selection of entries in the reference spectral library and, therefore, guided the selection of mineral classes shown on this map. Minerals occurring abundantly at the surface and those having unique spectral features were easily detected and discriminated. Minerals having similar spectral features were less easily discriminated, especially where the minerals were not particularly abundant and (or) where vegetation cover reduced the absorption strength of mineral features. Complications in reflectance calibration also affected the detection and identification of minerals.

The fate of nitrogen mineralized from leaf litter — Initial evidence from 15N-labeled litter

Treesearch

Kathryn B. Piatek

2011-01-01

Decomposition of leaf litter includes microbial immobilization of nitrogen (N), followed by N mineralization. The fate of N mineralized from leaf litter is unknown. I hypothesized that N mineralized from leaf litter will be re-immobilized into other forms of organic matter, including downed wood. This mechanism may retain N in some forests. To test this hypothesis, oak...

Evaluation of trace mineral source and preharvest deletion of trace minerals from finishing diets on tissue mineral status in pigs

PubMed Central

Ma, Y. L.; Webb, S. F.; Rentfrow, G.

2018-01-01

Objective An experiment was conducted to evaluate dietary supplemental trace mineral source and deletion on mineral content in tissues. Methods Weanling crossbred pigs (n = 144; 72 barrows and 72 gilts; body weight [BW] = 7.4±1.05 kg) were used. A basal diet was prepared, and trace mineral premix containing either inorganic (ITM) or organic (OTM) trace minerals (Cu, Fe, Mn, and Zn) was added to the basal diet. Pigs were blocked by sex and BW and randomly allotted to 24 pens for a total of 6 pigs per pen, and fed a diet containing either ITM or OTM supplemented at the 1998 NRC requirement estimates for each of 5 BW phases (Phase I to V) from 7 to 120 kg. The trace mineral supplementation was deleted for 6, 4, 2, and 0 wk of Phase V; regarding nutrient adequacy during this phase, the indigenous dietary Fe and Mn was sufficient, Cu was marginal and Zn was deficient. Results At the end of Phase IV, Mn content (mg/kg on the dry matter basis) was greater (p<0.05) in heart (0.77 vs 0.68), kidney (6.32 vs 5.87), liver (9.46 vs 8.30), and longissimus dorsi (LD; 0.30 vs 0.23) of pigs fed OTM. The pigs fed OTM were greater (p<0.05) in LD Cu (2.12 vs 1.89) and Fe (21.75 vs 19.40) and metacarpal bone Zn (141.86 vs 130.05). At the end of Phase V, increased length of deletion period (from 0 to 6 wk) resulted in a decrease (linear, p<0.01) in liver Zn (196.5 to 121.8), metacarpal bone Zn (146.6 to 86.2) and an increase (linear, p<0.01) in heart Mn (0.70 to 1.08), liver Mn (7.74 to 12.96), and kidney Mn (5.58 to 7.56). The only mineral source by deletion period interaction (p<0.05) was observed in LD Zn. Conclusion The results demonstrated differential effects of mineral deletion on tissue mineral content depending on both mineral assessed and source of the mineral. PMID:28728408

Protection of mineral deposits - a way towards difficult compromises

NASA Astrophysics Data System (ADS)

Radwanek-Bąk, Barbara; Nieć, Marek

2014-05-01

Mineral deposits are non-renewable natural resources. Their protection and reasonable exploitation are crucial requests resulting from sustainable development principles. Those are also fundamental issues in frame of the intergeneration justice and fairness concept. Protection of mineral resources should be based on interrelated activities: maintaining the possibility of economic use of the identified mineral resources, reduced consumption of mineral resources and ensuring satisfactory results of new prospecting and development of innovative technologies for the mineral resources base. The main problem with guarantee to the use of mineral resources is the accessibility to sites with documented deposits and prospective areas of their occurrence. Often, this contradicts with the interests of residents, planners and needs of the biotic environment protection, thus is often a source of conflicts. Legislative regulations are necessary to mitigate such arguable matters. SWOT analysis carried out with respect to introducing such legal regulations serves to identify the sources of conflicts and difficulties associated with their solution. Consensus reaching is a difficult task, so all decision makers are required to show their mutual understanding and willingness to achieve the goals taking into consideration all benefits for the population (including future generations). Foundations for finding the middle ground are: making the communities aware of their demands on minerals and of indispensable conditions for satisfying these demands; providing complete and accessible information; factual, non-emotional negotiations between decision makers and the public.

MitoMiner: a data warehouse for mitochondrial proteomics data

PubMed Central

Smith, Anthony C.; Blackshaw, James A.; Robinson, Alan J.

2012-01-01

MitoMiner (http://mitominer.mrc-mbu.cam.ac.uk/) is a data warehouse for the storage and analysis of mitochondrial proteomics data gathered from publications of mass spectrometry and green fluorescent protein tagging studies. In MitoMiner, these data are integrated with data from UniProt, Gene Ontology, Online Mendelian Inheritance in Man, HomoloGene, Kyoto Encyclopaedia of Genes and Genomes and PubMed. The latest release of MitoMiner stores proteomics data sets from 46 studies covering 11 different species from eumetazoa, viridiplantae, fungi and protista. MitoMiner is implemented by using the open source InterMine data warehouse system, which provides a user interface allowing users to upload data for analysis, personal accounts to store queries and results and enables queries of any data in the data model. MitoMiner also provides lists of proteins for use in analyses, including the new MitoMiner mitochondrial proteome reference sets that specify proteins with substantial experimental evidence for mitochondrial localization. As further mitochondrial proteomics data sets from normal and diseased tissue are published, MitoMiner can be used to characterize the variability of the mitochondrial proteome between tissues and investigate how changes in the proteome may contribute to mitochondrial dysfunction and mitochondrial-associated diseases such as cancer, neurodegenerative diseases, obesity, diabetes, heart failure and the ageing process. PMID:22121219

Effect of Mineral and Microbe Interactions on Biomass Yield

NASA Astrophysics Data System (ADS)

Pena, S. A.; Block, K. A.; Katz, A.; Gottlieb, P.

2016-12-01

The ecological feedback of microbes (bacteria and viruses) in association with minerals is virtually unexplored in the context of characterizing how carbon cycles in the terrestrial ecosystem. These interactions include the ability for bacteriophage to control bacteria populations, the ability of minerals to provide a substrate for bacteria growth, and the effect of minerals on bacteriophage viability. We investigate bacteriophage aggregation with minerals in the clay size fraction (< 0.2 µm) as well as the interaction between bacteriophage and mineral biofilms. In our virus experiments, bacteriophage Φ6 was suspended with the minerals smectite, illite, kaolinite, and goethite at low divalent cation concentrations so aggregation was in the reaction limited colloidal aggregation (RLCA) regime, at neutral pH and room temperature conditions. Virus remained viable at a 1:1 virus-clay ratio for clays, and at an approximate 100:1 ratio for goethite. However, the number of plaque forming units was reduced by 99%. Electron micrographs show viable as well as partially disassembled virus, similar to the results found by Block et al. 2014. We found that inactivation of a 4 x 1011 cm-3 concentration of bacteriophage Φ6 by smectite, illite, kaolinite, and goethite, required a minimum sediment concentration of 1.5 x 1011 cm-3, 1.4 x 1011 cm-3, 2.5 x 1011 cm-3, and 1.1 x 109 cm-3, respectively. Mineral biofilms were generated by suspension of tropical soil clays with gram-positive and gram-negative microbes and characterized by x-ray diffraction and imaged by electron microscopy (SEM and TEM). Mineral biomass produced by gram negative organisms were subjected to virus infection to determine influence of minerals on community resilience. Lastly, we report biomass yield in each instance to quantify the influence of mineral composition on total biomass production.

A Film Depositional Model of Permeability for Mineral Reactions in Unsaturated Media.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Freedman, Vicky L.; Saripalli, Prasad; Bacon, Diana H.

2004-11-15

A new modeling approach based on the biofilm models of Taylor et al. (1990, Water Resources Research, 26, 2153-2159) has been developed for modeling changes in porosity and permeability in saturated porous media and implemented in an inorganic reactive transport code. Application of the film depositional models to mineral precipitation and dissolution reactions requires that calculations of mineral films be dynamically changing as a function of time dependent reaction processes. Since calculations of film thicknesses do not consider mineral density, results show that the film porosity model does not adequately describe volumetric changes in the porous medium. These effects canmore » be included in permeability calculations by coupling the film permeability models (Mualem and Childs and Collis-George) to a volumetric model that incorporates both mineral density and reactive surface area. Model simulations demonstrate that an important difference between the biofilm and mineral film models is in the translation of changes in mineral radii to changes in pore space. Including the effect of tortuosity on pore radii changes improves the performance of the Mualem permeability model for both precipitation and dissolution. Results from simulation of simultaneous dissolution and secondary mineral precipitation provides reasonable estimates of porosity and permeability. Moreover, a comparison of experimental and simulated data show that the model yields qualitatively reasonable results for permeability changes due to solid-aqueous phase reactions.« less

Distribution and assessment of Pb in the supergene environment of the Huainan Coal Mining Area, Anhui, China.

PubMed

Fang, Ting; Liu, Guijian; Zhou, Chuncai; Yuan, Zijiao; Lam, Paul Kwan Sing

2014-08-01

Coal mining area is highly subject to lead (Pb) pollution from coal mining activities. Several decades of coal mining and processing practices in dozens of coal mines in the Huainan Coal Mining Area (HCMA) have led to the accumulation of massive amounts of coal gangue, which piled in dumps. In order to investigate the impacts of coal gangue dumps on Pb level in the supergene media of the HCMA, a systematic sampling campaign comprising coal gangue, soil, wheat, and earthworm samples was conducted. The average Pb content in the coal mining area soil is 24 mg/kg, which is slightly higher than the associated coal gangues (23 mg/kg) and markedly higher than reference region soil (12.6 mg/kg). Soil in the HCMA present a slight to moderate Pb contamination, which might be related to the weathering and leaching of coal gangue dumps. Lateral distribution of Pb in HCMA soil differed among individual coal mines. The soil profile distribution of Pb depends on both natural and anthropogenic contributions. Average Pb content is higher in roots than in stems, leaves, and wheat husks, while the Pb level in seeds exceeded the maximum Pb allowance for foods (Maximum Levels of Contaminants in Foods of China, GB 2762-2012). Earthworms in the selected area are significantly enriched in Pb, suggesting higher bio-available Pb level in soil in the HCMA.

Minerals yearbook: Mineral industries of Europe and central Eurasia. Volume 3. 1992 international review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-01-01

Volume III, Minerals Yearbook -- International Review contains the latest available mineral data on more than 175 foreign countries and discusses the importance of minerals to the economies of these nations. Since the 1989 International Review, the volume has been presented as six reports. The report presents the Mineral Industries of Europe and Central Eurasia. The report incorporates location maps, industry structure tables, and an outlook section previously incorporated in the authors' Minerals Perspectives Series quinquennial regional books, which are being discontinued. This section of the Minerals Yearbook reviews the minerals industries of 45 countries: the 12 nations of themore » European Community (EC); 6 of the 7 nations of the European Free Trade Association (EFTA); Malta; the 11 Eastern European economies in transition (Albania, Bosnia and Hercegovina, Bulgaria, Croatia, Czechoslovakia, Hungary, Macedonia, Poland, Romania, Serbia and Montenegro, and Slovenia); and the countries of Central Eurasia (Armenia, Azerbaijan, Belarus, Estonia, Georgia, Kazakhstan, Kyrgystan, Latvia, Lithuania, Moldova, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan).« less

Book review: Economic geology: Principles and practice: Metals, minerals, coal and hydrocarbons—Introduction to formation and sustainable exploitation of mineral deposits

USGS Publications Warehouse

Anderson, Eric

2013-01-01

This volume, available in both hardcover and paperback, is an English translation of the fifth edition of the German language text Mineralische und Energie-Rohstoffe. The book provides an extensive overview of natural resources and societal issues associated with extracting raw materials. The comprehensive list of raw materials discussed includes metals, industrial minerals, coal, and hydrocarbons. The book is divided into four parts: (1) “Metalliferous ore deposits,” (2) “Nonmetallic minerals and rocks,” (3) “Practice of economic geology,” and (4) “Fossil energy raw materials—coal, oil, and gas.” These sections are bound by a brief introduction and an extensive list of up-to-date references as well as an index. Each chapter begins with a concise synopsis and concludes with a summary that contains useful suggestions for additional reading. All figures are grayscale images and line drawings; however, several have been grouped together and reproduced as color plates. Also included is a companion website (www.wiley.com/go/pohl/geology) that contains additional resources, such as digital copies of figures, tables, and an expanded index, all available for download in easy-to-use formats.Economic Geology: Principles and Practice: Metals, Minerals, Coal and Hydrocarbons—Introduction to Formation and Sustainable Exploitation of Mineral Deposits. Walter l. Pohl. 2011. Wiley-Blackwell. Pp. 663. ISBN 978-1-4443-3663-4 (paperback).

Heterocoagulation of chalcopyrite and pyrite minerals in flotation separation.

PubMed

Mitchell, Timothy K; Nguyen, Anh V; Evans, Geoffrey M

2005-06-30

Heterocoagulation between various fine mineral particles contained within a mineral suspension with different structural and surface chemistry can interfere with the ability of the flotation processes to selectively separate the minerals involved. This paper examines the interactions between chalcopyrite (a copper mineral) and pyrite (an iron mineral often bearing gold) as they approach each other in suspensions with added chemicals, and relates the results to the experimental data for the flotation recovery and selectivity. The heterocoagulation was experimentally studied using the electrophoretic light scattering (ELS) technique and was modelled by incorporating colloidal forces, including the van der Waals, electrostatic double layer and hydrophobic forces. The ELS results indicated that pyrite has a positive zeta potential (zeta) up to its isoelectric point (IEP) at approximately pH 2.2, while chalcopyrite has a positive zeta up to its IEP at approximately pH 5.5. This produces heterocoagulation of chalcopyrite with pyrite between pH 2.2 and pH 5.5. The heterocoagulation was confirmed by the ELS spectra measured with a ZetaPlus instrument from Brookhaven and by small-scale flotation experiments.

The influence of mineral particles on fibroblast behaviour: A comparative study.

PubMed

Soto Veliz, Diosangeles; Luoto, Jens C; Pulli, Ilari; Toivakka, Martti

2018-07-01

Minerals are versatile tools utilised to modify and control the physical-chemical and functional properties of substrates. Those properties include ones directing cell fate; thus, minerals can potentially provide a direct and inexpensive method to manipulate cell behaviour. This paper shows how different minerals influence human dermal fibroblast behaviour depending on their properties. Different calcium carbonates, calcium sulphates, silica, silicates, and titanium dioxide were characterised using TEM, ATR-FTIR, and zeta potential measurements. Mineral-cell interactions were analysed through MTT assay, LDH assay, calcein AM staining, live cell imaging, immunofluorescence staining, western blot, and extra/intracellular calcium measurements. Results show that the interaction of the fibroblasts with the minerals was governed by a shared period of adaptation, followed by increased proliferation, growth inhibition, or increased toxicity. Properties such as size, ion release and chemical composition had a direct influence on the cells leading to cell agglomeration, morphological changes, and the possible formation of protein-mineral complexes. In addition, zeta potential and FTIR measurements of the minerals showed adsorption of the cell culture media onto the particles. This article provides fundamental insight into the mineral-fibroblast interactions, and makes it possible to arrange the minerals according to the time-dependent cellular response. Copyright © 2018 Elsevier B.V. All rights reserved.

43 CFR 3594.5 - Minerals soluble in water; brines; minerals taken in solution.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Minerals soluble in water; brines; minerals taken in solution. 3594.5 Section 3594.5 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SOLID...

43 CFR 3594.5 - Minerals soluble in water; brines; minerals taken in solution.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Minerals soluble in water; brines; minerals taken in solution. 3594.5 Section 3594.5 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SOLID...

43 CFR 3594.5 - Minerals soluble in water; brines; minerals taken in solution.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Minerals soluble in water; brines; minerals taken in solution. 3594.5 Section 3594.5 Public Lands: Interior Regulations Relating to Public Lands (Continued) BUREAU OF LAND MANAGEMENT, DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) SOLID...

Microbial Fossilization in Mineralizing Environments: Relevance for Mars "EXOPALEONTOLOGY"

NASA Technical Reports Server (NTRS)

Farmer, Jack D.; DesMarais, David J.; Morrison, David (Technical Monitor)

1994-01-01

The goals of post-Viking exobiology include the search for a Martian fossil record. How can we optimize future exploration efforts to search for fossils on Mars? The Precambrian fossil record indicates that key factors for the long-term preservation of microbial fossils include: 1) the rapid entombment and/or replacement of organisms and organic matter by fine-grained, stable mineral phases (e.g. silica, phosphate, and to a lesser extent, carbonate), 2) low-permeability host sediments (maintaining a closed chemical system during early diagenesis), and 3) shallow burial (maintaining post-depositional temperatures and pressures within the stability range for complex organic molecules). Modem terrestrial environments where early mineralization commonly occurs in association with microbial organisms include: subaerial thermal springs and shallow hydrothermal systems, sub-lacustrine springs and evaporites of alkaline lakes, and subsoil environments where hardpans (e.g. calcretes, silcretes) and duricrusts form. Studies of microbial fossilization in such environments provide important insights preservation patterns in Precambrian rocks, while also playing a role in the development of strategies for Mars exopaleontology. The refinement of site priorities for Mars exopaleontology is expected to benefit greatly from high resolution imaging and altimetry acquired during upcoming orbital missions, and especially infrared and gamma ray spectral data needed for determining surface composition. In anticipation of future orbital missions, constraints for identifying high priority mineral deposits on Mars are being developed through analog remote sensing studies of key mineralizing environments on Earth.

Co-Cu-Au deposits in metasedimentary rocks-A preliminary report

USGS Publications Warehouse

Slack, J.F.; Causey, J.D.; Eppinger, R.G.; Gray, J.E.; Johnson, C.A.; Lund, K.I.; Schulz, K.J.

2010-01-01

A compilation of data on global Co-Cu-Au deposits in metasedimentary rocks refines previous descriptive models for their occurrence and provides important information for mineral resource assessments and exploration programs. This compilation forms the basis for a new classification of such deposits, which is speculative at this early stage of research. As defined herein, the Co-Cu-Au deposits contain 0.1 percent or more by weight of Co in ore or mineralized rock, comprising disseminated to semi-massive Co-bearing sulfide minerals with associated Fe- and Cu-bearing sulfides, and local gold, concentrated predominantly within rift-related, siliciclastic metasedimentary rocks of Proterozoic age. Some deposits have appreciable Ag ? Bi ? W ? Ni ? Y ? rare earth elements ? U. Deposit geometry includes stratabound and stratiform layers, lenses, and veins, and (or) discordant veins and breccias. The geometry of most deposits is controlled by stratigraphic layering, folds, axial-plane cleavage, shear zones, breccias, or faults. Ore minerals are mainly cobaltite, skutterudite, glaucodot, and chalcopyrite, with minor gold, arsenopyrite, pyrite, pyrrhotite, bismuthinite, and bismuth; some deposits have appreciable tetrahedrite, uraninite, monazite, allanite, xenotime, apatite, scheelite, or molybdenite. Magnetite can be abundant in breccias, veins, or stratabound lenses within ore or surrounding country rocks. Common gangue minerals include quartz, biotite, muscovite, K-feldspar, albite, chlorite, and scapolite; many deposits contain minor to major amounts of tourmaline. Altered wall rocks generally have abundant biotite or albite. Mesoproterozoic metasedimentary successions constitute the predominant geologic setting. Felsic and (or) mafic plutons are spatially associated with many deposits and at some localities may be contemporaneous with, and involved in, ore formation. Geoenvironmental data for the Blackbird mining district in central Idaho indicate that weathering of

The Conterminous United States Mineral Assessment Program; background information to accompany folio of geologic, geochemical, remote sensing, and mineral resources maps of the Butte 1 degree x 2 degrees Quadrangle, Montana

USGS Publications Warehouse

Elliott, James E.; Trautwein, C.M.; Wallace, C.A.; Lee, G.K.; Rowan, L.C.; Hanna, W.F.

1993-01-01

The Butte 1?x2 ? quadrangle in west-central Montana was investigated as part of the U.S. Geological Survey's Conterminous United States Mineral Assessment Program (CUSMAP). These investigations included geologic mapping, geochemical surveys, gravity and aeromagnetic surveys, examinations of mineral deposits, and specialized geochronologic and remote-sensing studies. The data collected during these studies were compiled, combined with available published and unpublished data, analyzed, and used in a mineral-resource assessment of the quadrangle. The results, including data, interpretations, and mineral-resource assessments for nine types of mineral deposits, are published separately as a folio of maps. These maps are accompanied by figures, tables, and explanatory text. This circular provides background information on the Butte quadrangle, summarizes the studies and published maps, and lists a selected bibliography of references pertinent to the geology, geochemistry, geophysics, and mineral resources of the quadrangle. The Butte quadrangle, which includes the world-famous Butte mining district, has a long history of mineral production. Many mining districts within the quadrangle have produced large quantities of many commodities; the most important in dollar value of production were copper, gold, silver, lead, zinc, manganese, molybdenum, and phosphate. At present, mines at several locations produce copper, molybdenum, gold, silver, lead, zinc, and phosphate. Exploration, mainly for gold, has indicated the presence of other mineral deposits that may be exploited in the future. The results of the investigations by the U.S. Geological Survey indicate that many areas of the quadrangle are highly favorable for the occurrence of additional undiscovered resources of gold, silver, copper, molybdenum, tungsten, and other metals in several deposit types.

Ba'id al Jimalah tungsten prospect, Najd region, Kingdom of Saudi Arabia

NASA Astrophysics Data System (ADS)

Lofts, P. G.

The Ba'id al Jimalah tungsten prospect is located in the NE of the Arabian Shield, at 25°09'N, 42°41'E. Mineralization is associated with a late-Proterozoic, porphyritic microgranite emplaced in folded, fine-grained clastic rocks of the Murdama group, within an aureole of biotite-rich hornfels. The microgranite forms a 30 m-thick sill and numerous smaller sills and dikes cropping out along two low, sub-parallel ridges and several small hills in an area 700 m square. The form of the intrusion at depth is uncertain. It is slightly to intensely sericitized, in places greisenized, and is enriched in Li, F and Rb. Wolframite occurs with minor cassiterite, scheelite and sulfides in quartz veins cutting both microgranite and hornfelsed wall-rock. The veins have a dominant trend of 110-115°, and are thicker and more numerous in the microgranite. Gangue minerals include plagioclase and potassium feldspar, muscovite, sericite, fluorite and minor siderite. A major Najd fault trending 130-135° probably controlled magma emplacement and subsequent hydrothermal and pneumatolytic activity. A percussion drilling program, restricted to the outcrop of the sill on the north ridge, has outlined 800,000 tonnes grading 0.10% WO 3 and 0.01% Sn.

Version 3.0 of EMINERS - Economic Mineral Resource Simulator

USGS Publications Warehouse

Duval, Joseph S.

2012-01-01

Quantitative mineral resource assessment, as developed by the U.S. Geological Survey (USGS), consists of three parts: (1) development of grade and tonnage mineral deposit models; (2) delineation of tracts permissive for each deposit type; and (3) probabilistic estimation of the numbers of undiscovered deposits for each deposit type. The estimate of the number of undiscovered deposits at different levels of probability is the input to the EMINERS (Economic Mineral Resource Simulator) program. EMINERS uses a Monte Carlo statistical process to combine probabilistic estimates of undiscovered mineral deposits with models of mineral deposit grade and tonnage to estimate mineral resources. Version 3.0 of the EMINERS program is available as this USGS Open-File Report 2004-1344. Changes from version 2.0 include updating 87 grade and tonnage models, designing new templates to produce graphs showing cumulative distribution and summary tables, and disabling economic filters. The economic filters were disabled because embedded data for costs of labor and materials, mining techniques, and beneficiation methods are out of date. However, the cost algorithms used in the disabled economic filters are still in the program and available for reference for mining methods and milling techniques. The release notes included with this report give more details on changes in EMINERS over the years. EMINERS is written in C++ and depends upon the Microsoft Visual C++ 6.0 programming environment. The code depends heavily on the use of Microsoft Foundation Classes (MFC) for implementation of the Windows interface. The program works only on Microsoft Windows XP or newer personal computers. It does not work on Macintosh computers. For help in using the program in this report, see the "Quick-Start Guide for Version 3.0 of EMINERS-Economic Mineral Resource Simulator" (W.J. Bawiec and G.T. Spanski, 2012, USGS Open-File Report 2009-1057, linked at right). It demonstrates how to execute EMINERS software

Investigation of sorption interactions between oil shale principal mineral phases and organic compounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowen, J.M.

1988-09-01

The interactions between minerals representative of the bulk composition of oil shales and organic compounds that have been found in oil shale leachates were investigated. The method used to directly determine the type of interactions that could take place between organic compounds and oil shale mineral phases was Fourier transform infrared spectroscopy (FTIR) using several advanced detection methods, including diffuse reflectance (DRIFT) and photoacoustics (PAS). The minerals that were investigated include quartz, calcite, and dolomite, which are known to figure significantly in the composition of processed oil shales. The organic chemical compounds used were chosen from a list of compoundsmore » identified in spent oil shale leachates, and they include pyridine, phenol, p-cresol, and acetone. The sorption interactions for the study were prepared by exposing each of the minerals to the organic compounds by three different methods. These were vapor deposition, direct application, and immersion in an aqueous solution at pH 12. 41 refs., 3 figs., 4 tabs.« less

Prebiotics, probiotics, and synbiotics affect mineral absorption, bone mineral content, and bone structure.

PubMed

Scholz-Ahrens, Katharina E; Ade, Peter; Marten, Berit; Weber, Petra; Timm, Wolfram; Açil, Yahya; Glüer, Claus-C; Schrezenmeir, Jürgen

2007-03-01

Several studies in animals and humans have shown positive effects of nondigestible oligosaccharides (NDO) on mineral absorption and metabolism and bone composition and architecture. These include inulin, oligofructose, fructooligosaccharides, galactooligosaccharides, soybean oligosaccharide, and also resistant starches, sugar alcohols, and difructose anhydride. A positive outcome of dietary prebiotics is promoted by a high dietary calcium content up to a threshold level and an optimum amount and composition of supplemented prebiotics. There might be an optimum composition of fructooligosaccharides with different chain lengths (synergy products). The efficacy of dietary prebiotics depends on chronological age, physiological age, menopausal status, and calcium absorption capacity. There is evidence for an independent probiotic effect on facilitating mineral absorption. Synbiotics, i.e., a combination of probiotics and prebiotics, can induce additional effects. Whether a low content of habitual NDO would augment the effect of dietary prebiotics or synbiotics remains to be studied. The underlying mechanisms are manifold: increased solubility of minerals because of increased bacterial production of short-chain fatty acids, which is promoted by the greater supply of substrate; an enlargement of the absorption surface by promoting proliferation of enterocytes mediated by bacterial fermentation products, predominantly lactate and butyrate; increased expression of calcium-binding proteins; improvement of gut health; degradation of mineral complexing phytic acid; release of bone-modulating factors such as phytoestrogens from foods; stabilization of the intestinal flora and ecology, also in the presence of antibiotics; stabilization of the intestinal mucus; and impact of modulating growth factors such as polyamines. In conclusion, prebiotics are the most promising but also best investigated substances with respect to a bone-health-promoting potential, compared with probiotics

Measuring the Hardness of Minerals

ERIC Educational Resources Information Center

Bushby, Jessica

2005-01-01

The author discusses Moh's hardness scale, a comparative scale for minerals, whereby the softest mineral (talc) is placed at 1 and the hardest mineral (diamond) is placed at 10, with all other minerals ordered in between, according to their hardness. Development history of the scale is outlined, as well as a description of how the scale is used…

A Weighty Subject: Exploration for Heavy Minerals Across the State of Mississippi

NASA Astrophysics Data System (ADS)

Gifford, J.; Woolsey, A. I.; Yarbrough, L. D.; Platt, B. F.; Widanagamage, I. H.; Easson, G. L.

2017-12-01

Preliminary analysis has shown that an array of industrial minerals is known to occur in offshore deposits on the Gulf Coast as well as on-shore deposits in the Upper Cretaceous and Paleogene-Neogene clastic units, such as the Meridian Sand Member of the Eocene Tallahatta Formation in northeastern Mississippi. Furthermore, economic deposits occur within Holocene sediments along the Pearl and Pascagoula Rivers as well as along the modern Gulf of Mexico shoreline. These industrial minerals include suites of heavy minerals (specific gravity ≥2.97) that contain oxides of titanium (ilmenite, rutile, and leucoxene), oxides of zirconium (zircon), and the complex rare-earth-bearing phosphates (monazite and xenotime). These oxides are essential constituents of a wide-range of industrial materials critical to common technologies and the bulk of these mineral commodities are presently dependent on foreign supply. Current offshore deposits have been shown to be economic but are likely no longer accessible given their location within the Gulf Islands National Seashore. This comprehensive study is developing a heavy mineral occurrence dataset for the state of Mississippi including detailed analyses of the industrial mineral resources available within the state. More than 100 samples have been collected across the state from active and non-operating sand pit mining locations. The heavy mineral fraction of each sample was separated using lithium heteropolytungstates (LST) and gravity-based separation techniques. A grain mount for each sample was prepared with the heavy mineral fraction and the percentage values for each heavy mineral species were obtained from 200 grain counts per sample grain mount. Typical heavy mineral fraction for the sample set was approximately 0.9 % with an array from 0.0% to some samples ranging to a greater concentration of 7.5%. The resulting dataset will be further analyzed for geospatial similarities in trends and occurrences. Additional data

Chemometric analysis of minerals in gluten-free products.

PubMed

Gliszczyńska-Świgło, Anna; Klimczak, Inga; Rybicka, Iga

2018-06-01

Numerous studies indicate mineral deficiencies in people on a gluten-free (GF) diet. These deficiencies may indicate that GF products are a less valuable source of minerals than gluten-containing products. In the study, the nutritional quality of 50 GF products is discussed taking into account the nutritional requirements for minerals expressed as percentage of recommended daily allowance (%RDA) or percentage of adequate intake (%AI) for a model celiac patient. Elements analyzed were calcium, potassium, magnesium, sodium, copper, iron, manganese, and zinc. Analysis of %RDA or %AI was performed using principal component analysis (PCA) and hierarchical cluster analysis (HCA). Using PCA, the differentiation between products based on rice, corn, potato, GF wheat starch and based on buckwheat, chickpea, millet, oats, amaranth, teff, quinoa, chestnut, and acorn was possible. In the HCA, four clusters were created. The main criterion determining the adherence of the sample to the cluster was the content of all minerals included to HCA (K, Mg, Cu, Fe, Mn); however, only the Mn content differentiated four formed groups. GF products made of buckwheat, chickpea, millet, oats, amaranth, teff, quinoa, chestnut, and acorn are better source of minerals than based on other GF raw materials, what was confirmed by PCA and HCA. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Influence of changing water sources and mineral chemistry on the everglades ecosystem

USGS Publications Warehouse

McCormick, P.V.; Harvey, J.W.; Crawford, E.S.

2011-01-01

Human influences during the previous century increased mineral inputs to the Florida Everglades by changing the sources and chemistry of surface inflows. Biogeochemical responses to this enrichment include changes in the availability of key limiting nutrients such as P, the potential for increased turnover of nutrient pools due to accelerated plant decomposition, and increased rates of mercury methylation associated with sulfate enrichment. Mineral enrichment has also been linked to the loss of sensitive macrophyte species, although dominant Everglades species appear tolerant of a broad range of mineral chemistry. Shifts in periphyton community composition and function provide an especially sensitive indicator of mineral enrichment. Understanding the influence of mineral chemistry on Everglades processes and biota may improve predictions of ecosystem responses to ongoing hydrologic restoration efforts and provide guidelines for protecting remaining mineral-poor areas of this peatland. Copyright ?? 2011 Taylor & Francis Group, LLC.

An exploration in mineral supply chain mapping using tantalum as an example

USGS Publications Warehouse

Soto-Viruet, Yadira; Menzie, W. David; Papp, John F.; Yager, Thomas R.

2013-01-01

This report uses the supply chain of tantalum (Ta) to investigate the complexity of mineral and metal supply chains in general and show how they can be mapped. A supply chain is made up of all the manufacturers, suppliers, information networks, and so forth, that provide the materials and parts that go into making up a final product. The mineral portion of the supply chain begins with mineral material in the ground (the ore deposit); extends through a series of processes that include mining, beneficiation, processing (smelting and refining), semimanufacture, and manufacture; and continues through transformation of the mineral ore into concentrates, refined mineral commodities, intermediate forms (such as metals and alloys), component parts, and, finally, complex products. This study analyses the supply chain of tantalum beginning with minerals in the ground to many of the final goods that contain tantalum.

Scoping candidate minerals for stabilization of arsenic-bearing solid residuals.

PubMed

Raghav, Madhumitha; Shan, Jilei; Sáez, A Eduardo; Ela, Wendell P

2013-12-15

Arsenic Crystallization Technology (ACT) is a potentially eco-friendly, effective technology for stabilization of arsenic-bearing solid residuals (ABSRs). The strategy is to convert ABSRs generated by water treatment facilities into minerals with a high arsenic capacity and long-term stability in mature, municipal solid waste landfills. Candidate minerals considered in this study include scorodite, arsenate hydroxyapatites, ferrous arsenates (symplesite-type minerals), tooeleite, and arsenated-schwertmannite. These minerals were evaluated as to ease of synthesis, applicability to use of iron-based ABSRs as a starting material, and arsenic leachability. The Toxicity Characteristic Leaching Procedure (TCLP) was used for preliminary assessment of candidate mineral leaching. Minerals that passed the TCLP and whose synthesis route was promising were subjected to a more aggressive leaching test using a simulated landfill leachate (SLL) solution. Scorodite and arsenate hydroxyapatites were not considered further because their synthesis conditions were not found to be favorable for general application. Tooeleite and silica-amended tooeleite showed high TCLP arsenic leaching and were also not investigated further. The synthesis process and leaching of ferrous arsenate and arsenated-schwertmannite were promising and of these, arsenated-schwertmannite was most stable during SLL testing. The latter two candidate minerals warrant synthesis optimization and more extensive testing. Copyright © 2013 Elsevier B.V. All rights reserved.

Scoping Candidate Minerals for Stabilization of Arsenic-Bearing Solid Residuals

PubMed Central

Raghav, Madhumitha; Shan, Jilei; Sáez, A. Eduardo; Ela, Wendell P.

2014-01-01

Arsenic Crystallization Technology (ACT) is a potentially eco-friendly, effective technology for stabilization of arsenic-bearing solid residuals (ABSRs). The strategy is to convert ABSRs generated by water treatment facilities into minerals with a high arsenic capacity and long-term stability in mature, municipal solid waste landfills. Candidate minerals considered in this study include scorodite, arsenate hydroxyapatites, ferrous arsenates (symplesite-type minerals), tooeleite, and arsenated-schwertmannite. These minerals were evaluated as to ease of synthesis, applicability to use of iron-based ABSRs as a starting material, and arsenic leachability. The Toxicity Characteristic Leaching Procedure (TCLP) was used for preliminary assessment of candidate mineral leaching. Minerals that passed the TCLP and whose synthesis route was promising were subjected to a more aggressive leaching test using a simulated landfill leachate (SLL) solution. Scorodite and arsenate hydroxyapatites were not considered further because their synthesis conditions were not found to be favorable for general application. Tooeleite and silica-amended tooeleite showed high TCLP arsenic leaching and were also not investigated further. The synthesis process and leaching of ferrous arsenate and arsenated-schwertmannite were promising and of these, arsenated-schwertmannite was most stable during SLL testing. The latter two candidate minerals warrant synthesis optimization and more extensive testing. PMID:24231323

Neurologic disorders of mineral metabolism and parathyroid disease.

PubMed

Agrawal, Lily; Habib, Zeina; Emanuele, Nicholas V

2014-01-01

Disorders of mineral metabolism may cause neurologic manifestations of the central and peripheral nervous systems. This is because plasma calcium stabilizes excitable membranes in the nerve and muscle tissue, magnesium is predominantly intracellular and is required for activation of many intracellular enzymes, and extracellular magnesium affects synaptic transmission. This chapter reviews abnormalities in electrolytes and minerals which can be associated with several neuromuscular symptoms including neuromuscular irritability, mental status changes, cardiac and smooth muscle changes, etc. © 2014 Elsevier B.V. All rights reserved.

A systematic study of multiple minerals precipitation modelling in wastewater treatment.

PubMed

Kazadi Mbamba, Christian; Tait, Stephan; Flores-Alsina, Xavier; Batstone, Damien J

2015-11-15

Mineral solids precipitation is important in wastewater treatment. However approaches to minerals precipitation modelling are varied, often empirical, and mostly focused on single precipitate classes. A common approach, applicable to multi-species precipitates, is needed to integrate into existing wastewater treatment models. The present study systematically tested a semi-mechanistic modelling approach, using various experimental platforms with multiple minerals precipitation. Experiments included dynamic titration with addition of sodium hydroxide to synthetic wastewater, and aeration to progressively increase pH and induce precipitation in real piggery digestate and sewage sludge digestate. The model approach consisted of an equilibrium part for aqueous phase reactions and a kinetic part for minerals precipitation. The model was fitted to dissolved calcium, magnesium, total inorganic carbon and phosphate. Results indicated that precipitation was dominated by the mineral struvite, forming together with varied and minor amounts of calcium phosphate and calcium carbonate. The model approach was noted to have the advantage of requiring a minimal number of fitted parameters, so the model was readily identifiable. Kinetic rate coefficients, which were statistically fitted, were generally in the range 0.35-11.6 h(-1) with confidence intervals of 10-80% relative. Confidence regions for the kinetic rate coefficients were often asymmetric with model-data residuals increasing more gradually with larger coefficient values. This suggests that a large kinetic coefficient could be used when actual measured data is lacking for a particular precipitate-matrix combination. Correlation between the kinetic rate coefficients of different minerals was low, indicating that parameter values for individual minerals could be independently fitted (keeping all other model parameters constant). Implementation was therefore relatively flexible, and would be readily expandable to include other

Bone mineral density in subjects using central nervous system-active medications.

PubMed

Kinjo, Mitsuyo; Setoguchi, Soko; Schneeweiss, Sebastian; Solomon, Daniel H

2005-12-01

Decreased bone mineral density defines osteoporosis according to the World Health Organization and is an important predictor of future fractures. The use of several types of central nervous system-active drugs, including benzodiazepines, anticonvulsants, antidepressants, and opioids, have all been associated with increased risk of fracture. However, it is unclear whether such an increase in risk is related to an effect of bone mineral density or to other factors, such as increased risk of falls. We sought to examine the relationship between bone mineral density and the use of benzodiazepines, anticonvulsants, antidepressants, and opioids in a representative US population-based sample. We analyzed data on adults aged 17 years and older from the Third National Health and Nutrition Examination Survey (NHANES III, 1988-1994). Total femoral bone mineral density of 7114 male and 7532 female participants was measured by dual-energy x-ray absorptiometry. Multivariable linear regression models were used to quantify the relation between central nervous system medication exposure and total femoral bone mineral density. Models controlled for relevant covariates, including age, sex, and body mass index. In linear regression models, significantly reduced bone mineral density was found in subjects taking anticonvulsants (0.92 g/cm2; 95% confidence interval [CI]: 0.89 to 0.94) and opioids (0.92 g/cm2; 95% CI: 0.88 to 0.95) compared with nonusers (0.95 g/cm2; 95% CI: 0.95 to 0.95) after adjusting for several potential confounders. The other central nervous system-active drugs--benzodiazepines or antidepressants--were not associated with significantly reduced bone mineral density. In cross-sectional analysis of NHANES III, anticonvulsants and opioids (but not benzodiazepines or antidepressants) were associated with significantly reduced bone mineral density. These findings have implications for fracture-prevention strategies.

Interactions Between Snow-Adapted Organisms, Minerals and Snow in a Mars-Analog Environment, and Implications for the Possible Formation of Mineral Biosignatures

NASA Astrophysics Data System (ADS)

Hausrath, E.; Bartlett, C. L.; Garcia, A. H.; Tschauner, O. D.; Murray, A. E.; Raymond, J. A.

2015-12-01

Increasing evidence suggests that icy environments on bodies such as Mars, Europa, and Enceladus may be important potential habitats in our solar system. Life in icy environments faces many challenges, including water limitation, temperature extremes, and nutrient limitation. Understanding how life has adapted to withstand these challenges on Earth may help understand potential life on other icy worlds, and understanding the interactions of such life with minerals may help shed light on the detection of possible mineral biosignatures. Snow environments, being particularly nutrient limited, may require specific adaptations by the microbiota living there. Previous observations have suggested that associated minerals and microorganisms play an important role in snow algae micronutrient acquisition. Here, in order to interpret micronutrient uptake by snow algae, and potential formation of mineral biosignatures, we present observations of interactions between snow algae and associated microorganisms and minerals in both natural, Mars-analog environments, and laboratory experiments. Samples of snow, dust, snow algae, and microorganisms were collected from Mount Anderson Ridge, CA. Some samples were DAPI-stained and analyzed by epifluorescent microscopy, and others were freeze-dried and examined by scanning electron microscopy, synchrotron X-ray diffraction (XRD) and synchrotron X-ray fluorescence (XRF). Xenic cultures of the snow alga Chloromonas brevispina were also grown under Fe-limiting conditions with and without the Fe-containing mineral nontronite to determine impacts of the mineral on algal growth. Observations from epifluorescent microscopy show bacteria closely associated with the snow algae, consistent with a potential role in micronutrient acquisition. Particles are also present on the algal cell walls, and synchrotron-XRD and XRF observations indicate that they are Fe-rich, and may therefore be a micronutrient source. Laboratory experiments indicated

Modeling CO2-Water-Mineral Wettability and Mineralization for Carbon Geosequestration.

PubMed

Liang, Yunfeng; Tsuji, Shinya; Jia, Jihui; Tsuji, Takeshi; Matsuoka, Toshifumi

2017-07-18

Carbon dioxide (CO 2 ) capture and storage (CCS) is an important climate change mitigation option along with improved energy efficiency, renewable energy, and nuclear energy. CO 2 geosequestration, that is, to store CO 2 under the subsurface of Earth, is feasible because the world's sedimentary basins have high capacity and are often located in the same region of the world as emission sources. How CO 2 interacts with the connate water and minerals is the focus of this Account. There are four trapping mechanisms that keep CO 2 in the pores of subsurface rocks: (1) structural trapping, (2) residual trapping, (3) dissolution trapping, and (4) mineral trapping. The first two are dominated by capillary action, where wettability controls CO 2 and water two-phase flow in porous media. We review state-of-the-art studies on CO 2 /water/mineral wettability, which was found to depend on pressure and temperature conditions, salt concentration in aqueous solutions, mineral surface chemistry, and geometry. We then review some recent advances in mineral trapping. First, we show that it is possible to reproduce the CO 2 /water/mineral wettability at a wide range of pressures using molecular dynamics (MD) simulations. As the pressure increases, CO 2 gas transforms into a supercritical fluid or liquid at ∼7.4 MPa depending on the environmental temperature. This transition leads to a substantial decrease of the interfacial tension between CO 2 and reservoir brine (or pure water). However, the wettability of CO 2 /water/rock systems depends on the type of rock surface. Recently, we investigated the contact angle of CO 2 /water/silica systems with two different silica surfaces using MD simulations. We found that contact angle increased with pressure for the hydrophobic (siloxane) surface while it was almost constant for the hydrophilic (silanol) surface, in excellent agreement with experimental observations. Furthermore, we found that the CO 2 thin films at the CO 2 -hydrophilic

Mineral resources of Novokuznetsk administrative district of Kemerovo region (metallic and non-metallic minerals)

NASA Astrophysics Data System (ADS)

Gutak, Ja M.

2017-09-01

The article summarizes data on metallic and non-metallic minerals of Novokuznetsk district of Kemerovo region. Consistently reviewed are iron deposits (Tersinskaya group of deposits), gold deposits (placer accumulations and vein gold deposits), mineral water deposits (Tersinskoe deposit), deposit of refractory clay (Barkinskoe) and wide spread mineral deposits such as brick clay, keramzite materials, sand and gravel, building stones, ornamental stones, facing stones, peat, materials for lime production. It is indicated that resource base of metallic and nonmetallic minerals is inferior to that of mineral coal. At the same time it can be of considerable interest to small and medium-size businesses as objects with quick return of investment (facing and ornamental stones). For a number of wide spread mineral resources (brick clay, keramzite materials, sand and gravel) it is an important component of local industry.

The Balmat-Edwards zinc-lead deposits-synsedimentary ore from Mississippi valley-type fluids.

USGS Publications Warehouse

Whelan, J.F.; Rye, R.O.; Delorraine, W.

1984-01-01

The Balmat-Edwards Zn-Pb district in New York is in Mid-Proterozoic Grenville marbles. Tabular to podiform, generally conformable massive sphalerite-galena orebodies occur at various horizons in the approx 1 km-thick marbles. Metamorphism obscured or obliterated most primary characteristics, whose reconstruction is attempted through detailed S, C, and O isotope studies of the Fowler orebody, and trace element and S isotope studies of sphalerite concentrates and composite ore samples from 22 orebodies. Sulphur isotope data reflect equilibration at near peak metamorphism with some indication of re-equilibration during retrograde metamorphism. The carbon and oxygen isotope composition of gangue carbonates suggests derivation from the host marbles. The oxygen isotope composition of gangue quartz is compatible with a chert origin or metamorphism-equilibration with other minerals. Sulphur and lead isotopes and sulphide mineralogy suggests that the ore fluids were evolved basin brines, chemically like those responsible for Mississippi Valley-type deposits. The large stratigraphic span (> 600 m) of the Balmat orebodies may be due to basin dewatering of million-year intervals. Stratigraphically increasing 34S values of evaporite-anhydrite are postulated to record hydrothermal events and to imply bacterial sulphate reduction on an unusually large scale. Such a stratigraphic increase may be a general exploration guide where sediment-hosted exhalative deposits or Mississippi Valley-type deposits occur.-G.J.N.

Enrichment of enzymatically mineralized gellan gum hydrogels with phlorotannin-rich Ecklonia cava extract Seanol(®) to endow antibacterial properties and promote mineralization.

PubMed

Douglas, Timothy E L; Dokupil, Agnieszka; Reczyńska, Katarzyna; Brackman, Gilles; Krok-Borkowicz, Malgorzata; Keppler, Julia K; Božič, Mojca; Van Der Voort, Pascal; Pietryga, Krzysztof; Samal, Sangram Keshari; Balcaen, Lieve; van den Bulcke, Jan; Van Acker, Joris; Vanhaecke, Frank; Schwarz, Karin; Coenye, Tom; Pamuła, Elżbieta

2016-08-10

Hydrogels offer several advantages as biomaterials for bone regeneration, including ease of incorporation of soluble substances such as mineralization-promoting enzymes and antibacterial agents. Mineralization with calcium phosphate (CaP) increases bioactivity, while antibacterial activity reduces the risk of infection. Here, gellan gum (GG) hydrogels were enriched with alkaline phosphatase (ALP) and/or Seanol(®), a seaweed extract rich in phlorotannins (brown algae-derived polyphenols), to induce mineralization with CaP and increase antibacterial activity, respectively. The sample groups were unmineralized hydrogels, denoted as GG, GG/ALP, GG/Seanol and GG/Seanol/ALP, and hydrogels incubated in mineralization medium (0.1 M calcium glycerophosphate), denoted as GG/ALP_min, GG/Seanol_min and GG/Seanol/ALP_min. Seanol(®) enhanced mineralization with CaP and also increased compressive modulus. Seanol(®) and ALP interacted in a non-covalent manner. Release of Seanol(®) occurred in a burst phase and was impeded by ALP-mediated mineralization. Groups GG/Seanol and GG/ALP/Seanol exhibited antibacterial activity against methicillin-resistant Staphylococcus aureus. GG/Seanol/ALP_min, but not GG/Seanol_min, retained some antibacterial activity. Eluates taken from groups GG/ALP_min, GG/Seanol_min and GG/ALP/Seanol_min displayed comparable cytotoxicity towards MG-63 osteoblast-like cells. These results suggest that enrichment of hydrogel biomaterials with phlorotannin-rich extracts is a promising strategy to increase mineralizability and antibacterial activity.

The Miner's Canary

ERIC Educational Resources Information Center

Guinier, Lani

2005-01-01

Miners used canaries as early warning signals: when a canary gasped for breath, the miners knew there was a problem with the atmosphere in the mine. The experience of people of color in higher education can be used similarly as a diagnostic tool.

Observation of nitrate coatings on atmospheric mineral dust particles

NASA Astrophysics Data System (ADS)

Li, W. J.; Shao, L. Y.

2009-03-01

Nitrate compounds have received much attention because of their ability to alter the hygroscopic properties and cloud condensation nuclei (CCN) activity of mineral dust particles in the atmosphere. However, very little is known about specific characteristics of ambient nitrate-coated mineral particles on an individual particle scale. In this study, sample collection was conducted during brown haze and dust episodes between 24 May and 21 June 2007 in Beijing, northern China. Sizes, morphologies, and compositions of 332 mineral dust particles together with their coatings were analyzed using transmission electron microscopy (TEM) coupled with energy-dispersive X-ray (EDX) microanalyses. Structures of some mineral particles were verified using selected-area electron diffraction (SAED). TEM observation indicates that approximately 90% of the collected mineral particles are covered by visible coatings in haze samples whereas only 5% are coated in the dust sample. 92% of the analyzed mineral particles are covered with Ca-, Mg-, and Na-rich coatings, and 8% are associated with K- and S-rich coatings. The majority of coatings contain Ca, Mg, O, and N with minor amounts of S and Cl, suggesting that they are possibly nitrates mixed with small amounts of sulfates and chlorides. These nitrate coatings are strongly correlated with the presence of alkaline mineral components (e.g., calcite and dolomite). CaSO4 particles with diameters from 10 to 500 nm were also detected in the coatings including Ca(NO3)2 and Mg(NO3)2. Our results indicate that mineral particles in brown haze episodes were involved in atmospheric heterogeneous reactions with two or more acidic gases (e.g., SO2, NO2, HCl, and HNO3). Mineral particles that acquire hygroscopic nitrate coatings tend to be more spherical and larger, enhancing their light scattering and CCN activity, both of which have cooling effects on the climate.

43 CFR 3815.1 - Mineral locations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Mineral locations. 3815.1 Section 3815.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LANDS AND MINERALS SUBJECT TO LOCATION Mineral Locations in Stock Driveway Withdrawals § 3815.1 Mineral locations. Under authority of the provisions of the...

43 CFR 3815.1 - Mineral locations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Mineral locations. 3815.1 Section 3815.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LANDS AND MINERALS SUBJECT TO LOCATION Mineral Locations in Stock Driveway Withdrawals § 3815.1 Mineral locations. Under authority of the provisions of the...

43 CFR 3815.1 - Mineral locations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Mineral locations. 3815.1 Section 3815.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LANDS AND MINERALS SUBJECT TO LOCATION Mineral Locations in Stock Driveway Withdrawals § 3815.1 Mineral locations. Under authority of the provisions of the...

43 CFR 3815.1 - Mineral locations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Mineral locations. 3815.1 Section 3815.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LANDS AND MINERALS SUBJECT TO LOCATION Mineral Locations in Stock Driveway Withdrawals § 3815.1 Mineral locations. Under authority of the provisions of the...

Trace element geochemistry of zircons from mineralizing and non-mineralizing igneous rocks related to gold ores at Yanacocha, Peru

NASA Astrophysics Data System (ADS)

Koleszar, A. M.; Dilles, J. H.; Kent, A. J.; Wooden, J. L.

2012-12-01

Zircons record important details about the evolution of magmatic systems, are relatively insensitive to alteration, and have been used to investigate the geochemistry, temperature, and oxidation state of volcanic and plutonic system. We examine zircons that span 6-7 m.y. of calc-alkaline volcanic activity in the Yanacocha district of northern Peru, where dacitic intrusions are associated with high-sulfidation gold deposits. The 14.5-8.4 Ma Yanacocha Volcanics include cogenetic lavas and pyroclastic rocks and are underlain by the andesites and dacites of the Calipuy Group, the oldest Cenozoic rocks in the region. We present data for magmatic zircons from the Cerro Fraile dacitic pyroclastics (15.5-15.1 Ma) of the Calipuy Group, and multiple eruptive units within the younger Yanacocha Volcanics: the Atazaico Andesite (14.5-13.3 Ma), the Quilish Dacite (~14-12 Ma), the Azufre Andesite (12.1-11.6 Ma), the San Jose Ignimbrite (11.5-11.2 Ma), and the Coriwachay Dacite (11.1-8.4 Ma). Epithermal high sulfidation (alunite-bearing) gold deposits are associated with the dacite intrusions of the Coriwachay and Quilish Dacites. Zircons from the non-mineralizing rocks typically have lower Hf concentrations and record Ti-in-zircon temperatures that are ~100°C hotter than zircons from the mineralizing intrusions. Temperatures recorded by zircons from the mineralizing intrusions are remarkably similar to those of the underlying Cerro Fraile dacite pyroclastics, but the zircons discussed here generally record SHRIMP-RG 206Pb/238U ages within error of previously published Ar-Ar eruption ages (eliminating antecrystic or xenocrystic origins). These observations suggest that zircons in the mineralizing intrusions form after greater extents of crystallization (and thus record elevated Hf concentrations and lower temperatures) than do zircons in the non-mineralized deposits. Unlike zircons from mineralized units associated with the porphyry Cu(Mo) deposits in Yerington, Nevada, which

Electron microprobe mineral analysis guide

NASA Technical Reports Server (NTRS)

Brown, R. W.

1980-01-01

Electron microprobe mineral analysis guide is a compilation of X-ray tables and spectra recorded from various mineral matrices. Spectra were obtained using electron microprobe, equipped with LiF geared, curved crystal X-ray spectrometers, utilizing typical analytical operating conditions: 15 Kv acceleration potential, 0.02 microampere sample current as measured on a clinopyroxene standard (CP19). Tables and spectra are presented for the majority of elements, fluorine through uranium, occurring in mineral samples from lunar, meteoritic and terrestrial sources. Tables for each element contain relevant analytical information, i.e., analyzing crystal, X-ray peak, background and relative intensity information, X-ray interferences and a section containing notes on the measurement. Originally intended to cover silicates and oxide minerals the tables and spectra have been expanded to cover other mineral phases. Electron microprobe mineral analysis guide is intended as a spectral base to which additional spectra can be added as the analyst encounters new mineral matrices.

Stable mineral recrystallization in low temperature aqueous systems: A critical review

NASA Astrophysics Data System (ADS)

Gorski, Christopher A.; Fantle, Matthew S.

2017-02-01

Minerals may undergo recrystallization reactions in low temperature (<100 °C) aqueous systems, during which they exchange isotopes and trace elements with the dissolved reservoir without undergoing overt structural, bulk compositional, or morphological changes. These interfacial reactions, which are often referred to in the literature as "atom exchange" and herein as "stable mineral recrystallization", have important implications for the use of isotopic and elemental proxies to interpret past temperatures, oxidation states, and aqueous chemistries on Earth. The reactions are also significant for modern environments, including engineered systems, as they imply that mineral lattices may be substantially more open to exchanging toxic elements and radionuclides with coexisting solutions than previously thought. To date, observations of stable mineral recrystallization are distributed among several disciplines, and no work has attempted to review their findings comprehensively. Accordingly, this review article presents laboratory evidence for stable mineral recrystallization, describes data collection and interpretation strategies, summarizes similar recrystallization systematics observed in multiple studies, explores the potential occurrence of stable mineral recrystallization in natural systems, and discusses possible mechanisms by which stable mineral recrystallization occurs. The review focuses primarily on carbonates, sulfates, and iron oxides because these minerals have been studied most extensively to date. The review concludes by presenting key questions that should be addressed in this field to further understand and account for stable mineral recrystallization in natural and engineered aqueous systems at low temperatures.

Effects of clay minerals on diethyl phthalate degradation in Fenton reactions.

PubMed

Chen, Ning; Fang, Guodong; Zhou, Dongmei; Gao, Juan

2016-12-01

Phthalate esters are a group of plasticizers, which are commonly detected in China's soils and surface water. Fenton reactions are naturally occurring and widely applied in the degradation of contaminants. However, limited research was considered the effects of clay minerals on contaminants degradation with OH oxidation. In this study, batch experiments were conducted to investigate the degradation of diethyl phthalate (DEP) in Fenton reactions in the presence of clay minerals, and the effects of clay type, Fe content in clay structure. The results showed the clay adsorption inhibited total degradation of DEP, and Fe content in clay structure played an important role in DEP degradation, including in solution and adsorbed in clay minerals. Clay minerals with less Fe content (<3%) quenched OH radical, while nontronite with Fe content 19.2% improved OH radical generation and accelerated DEP degradation in solution. The degradation of clay-adsorbed DEP was much slower than DEP in solution. Six main products of DEP degradation were identified, including monoethyl phthalate, phthalate acid, hydroxyl diethyl phthalate, etc. This study implied that phthalate ester's degradation would be much slower in natural water than expected in the presence of clay minerals. Copyright © 2016 Elsevier Ltd. All rights reserved.

30 CFR 57.5070 - Miner training.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Miner training. 57.5070 Section 57.5070 Mineral... Agents, and Diesel Particulate Matter Diesel Particulate Matter-Underground Only § 57.5070 Miner training. (a) Mine operators must provide annual training to all miners at a mine covered by this part who can...

43 CFR 3816.1 - Mineral locations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Mineral locations. 3816.1 Section 3816.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LANDS AND MINERALS SUBJECT TO LOCATION Mineral Locations in Reclamation Withdrawals § 3816.1 Mineral locations. The Act of April 23, 1932 (47 Stat. 136; 43...

43 CFR 3816.1 - Mineral locations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Mineral locations. 3816.1 Section 3816.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LANDS AND MINERALS SUBJECT TO LOCATION Mineral Locations in Reclamation Withdrawals § 3816.1 Mineral locations. The Act of April 23, 1932 (47 Stat. 136; 43...

43 CFR 3816.1 - Mineral locations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Mineral locations. 3816.1 Section 3816.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LANDS AND MINERALS SUBJECT TO LOCATION Mineral Locations in Reclamation Withdrawals § 3816.1 Mineral locations. The Act of April 23, 1932 (47 Stat. 136; 43...

43 CFR 3816.1 - Mineral locations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Mineral locations. 3816.1 Section 3816.1..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LANDS AND MINERALS SUBJECT TO LOCATION Mineral Locations in Reclamation Withdrawals § 3816.1 Mineral locations. The Act of April 23, 1932 (47 Stat. 136; 43...

HIV and syphilis infection among gold and diamond miners--Guyana, 2004.

PubMed

Seguy, N; Denniston, M; Hladik, W; Edwards, M; Lafleur, C; Singh-Anthony, S; Diaz, T

2008-11-01

Guyana had an estimated HIVprevalence of 1.5% among pregnant women in 2006 (95% confidence interval [CI] = 1.1-1.9). However, a survey of miners in one mine found a 6.5% HIV prevalence in 2002. To determine whether Guyanese miners are at high risk for HIV infection we conducted a HIV and syphilis prevalence survey of miners in several mines. Adult male consenting miners in 45 Guyanese mines were interviewed, counselled, tested for HIV and syphilis with rapid tests and provided onsite test results. The survey was cross-sectional and used a multi-stage cluster sampling design; population estimates were calculated using SUDAAN. Of 651 miners approached, 539 (83%) were interviewed and 509 (78%) tested. The estimated prevalence for HIV was 3.9% (CI = 2.1, 7.1) and for life-time syphilis exposure was 6.4% (CI = 4.5, 9.1). Fifty-four per cent (CI = 41.3, 66.7) of miners had casual sex during the preceding year, of whom 44.4% (CI = 34.3, 55.0) had always used condoms with these partners. The estimated HIV prevalence among Guyanese miners was higher than that of the general population. Targeted interventions including condom promotion are recommended to prevent further spread of HIV and other sexually transmitted infections among miners.

Inulin and oligofructose and mineral metabolism: the evidence from animal trials.

PubMed

Scholz-Ahrens, Katharina E; Schrezenmeir, Jürgen

2007-11-01

Nondigestible oligosaccharides have been shown to increase the absorption of several minerals (calcium, magnesium, in some cases phosphorus) and trace elements (mainly copper, iron, zinc). Inulin-type fructans including oligofructose and fructooligosaccharides derived from sucrose by enzymatic transfructosylation are the best investigated food ingredients in this respect. The stimulation of absorption was more pronounced when the demand for calcium was high, i.e., in animals in the rapid growing stage and in animals with impaired calcium absorption because of either ovariectomy or gastrectomy. Even a small stimulation of calcium absorption increased the mineral accumulation in the skeleton because of its persisting effect over months. Inulin-type fructans stimulated mineral absorption and bone mineral accretion when combined with probiotic lactobacilli and in the presence of antibiotics. Direct comparison of different inulin-type fructans revealed a more pronounced effect by inulin or a mixture of long-chain inulin and oligofructose than by oligofructose alone. Mechanisms on how inulin-type fructans mediate this effect include acidification of the intestinal lumen by short-chain fatty acids increasing solubility of minerals in the gut, enlargement of the absorption surface, increased expression of calcium-binding proteins mainly in the large intestine, modulated expression of bone-relevant cytokines, suppression of bone resorption, increased bioavailability of phytoestrogens, and, via stimulation of beneficial commensal microorganisms, increase of calcium uptake by enterocytes. Under certain conditions, inulin-type fructans may improve mineral absorption by their impact on the amelioration of gut health including stabilization of the intestinal flora and reduction of inflammation. The abundance of reports indicate that inulin-type fructans are promising substances that could help to improve the supply with available calcium in human nutrition and by this contribute

Geophysical technique for mineral exploration and discrimination based on electromagnetic methods and associated systems

DOEpatents

Zhdanov,; Michael, S [Salt Lake City, UT

2008-01-29

Mineral exploration needs a reliable method to distinguish between uneconomic mineral deposits and economic mineralization. A method and system includes a geophysical technique for subsurface material characterization, mineral exploration and mineral discrimination. The technique introduced in this invention detects induced polarization effects in electromagnetic data and uses remote geophysical observations to determine the parameters of an effective conductivity relaxation model using a composite analytical multi-phase model of the rock formations. The conductivity relaxation model and analytical model can be used to determine parameters related by analytical expressions to the physical characteristics of the microstructure of the rocks and minerals. These parameters are ultimately used for the discrimination of different components in underground formations, and in this way provide an ability to distinguish between uneconomic mineral deposits and zones of economic mineralization using geophysical remote sensing technology.

Performance analysis of mineral mapping method to delineate mineralization zones under tropical region

NASA Astrophysics Data System (ADS)

Wakila, M. H.; Saepuloh, A.; Heriawan, M. N.; Susanto, A.

2016-09-01

Geothermal explorations and productions are currently being intensively conducted at certain areas in Indonesia such as Wayang Windu Geothermal Field (WWGF) in West Java, Indonesia. The WWGF is located at wide area covering about 40 km2. An accurate method to map the distribution of heterogeneity minerals is necessary for wide areas such as WWGF. Mineral mapping is an important method in geothermal explorations to determine the distribution of minerals which indicate the surface manifestations of geothermal system. This study is aimed to determine the most precise and accurate methods for minerals mapping at geothermal field. Field measurements were performed to assess the accuracy of three proposed methods: 1) Minimum Noise Fraction (MNF), utilizing the linear transformation method to eliminate the correlation among the spectra bands and to reduce the noise in the data, 2) Pixel Purity Index (PPI), a designed method to find the most extreme spectrum pixels and their characteristics due to end-members mixing, 3) Spectral Angle Mapper (SAM), an image classification technique by measuring the spectral similarity between an unknown object with spectral reference in n- dimension. The output of those methods were mineral distribution occurrence. The performance of each mapping method was analyzed based on the ground truth data. Among the three proposed method, the SAM classification method is the most appropriate and accurate for mineral mapping related to spatial distribution of alteration minerals.

Mineral resource of the month: perlite

USGS Publications Warehouse

,

2010-01-01

The article talks about perlite, which is a mineral used as an aggregate for lightweight construction products, filler for paints and horticultural soil blends. Perlite comes from viscous lava, mined and processed to produce lightweight material that competes with pumice, exfoliated vermiculite and expanded clay and shale. It is mined in about 35 countries that include Greece, Japan and the U.S. Other uses include insulation, concrete and plaster aggregate, and stonewashing.

Spatial databases of the Humboldt Basin mineral resource assessment, northern Nevada

USGS Publications Warehouse

Mihalasky, Mark J.; Moyer, Lorre A.

2004-01-01

This report describes the origin, generation, and format of tract map databases for deposit types that accompany the metallic mineral resource assessment for the Humboldt River Basin, northern Nevada, (Wallace and others, 2004, Chapter 2). The deposit types include pluton-related polymetallic, sedimentary rock-hosted Au-Ag, and epithermal Au-Ag. The tract maps constitute only part of the assessment, which also includes new research and data for northern Nevada, discussions on land classification, and interpretation of the assessment maps. The purpose of the assessment was to identify areas that may have a greater favorability for undiscovered metallic mineral deposits, provide analysis of the mineral-resource favorability, and present the assessment of the Humboldt River basin and adjacent areas in a digital format using a Geographic Information System (GIS).

Arsenic mineral dissolution and possible mobilization in mineral-microbe-groundwater environment.

PubMed

Islam, A B M R; Maity, Jyoti Prakash; Bundschuh, Jochen; Chen, Chien-Yen; Bhowmik, Bejon Kumar; Tazaki, Kazue

2013-11-15

Arsenic (As) is widely distributed in the nature as ores or minerals. It has been attracted much attention for the global public health issue, especially for groundwater As contamination. The aim of this study was to elucidate the characteristics of microbes in groundwater where As-minerals were dissolved. An ex situ experiment was conducted with 7 standard As-minerals in bacteria-free groundwater and stored in experimental vessels for 1 year without supplementary nutrients. The pH (6.7-8.4) and EhS.H.E. (24-548 mV) changed between initial (0 day) and final stages (365 days) of experiment. The dissolution of As was detected higher from arsenolite (4240 ± 8.69 mg/L) and native arsenic (4538 ± 9.02 mg/L), whereas moderately dissolved from orpiment (653 ± 3.56 mg/L) and realgar (319 ± 2.56 mg/L) in compare to arsenopyrite (85 ± 1.25mg/L) and tennantite (3 ± 0.06 mg/L). Optical microscopic, scanning electron microscopic observations and flurometric enumeration revealed the abundance of As-resistant bacillus, coccus and filamentous types of microorganisms on the surface of most of As-mineral. 4'-6-Diamidino-2-phenylindole (DAPI)-stained epifluorescence micrograph confirmed the presence of DNA and carboxyfluorescein diacetate (CFDA) staining method revealed the enzymatically active bacteria on the surface of As-minerals such as in realgar (As4S4). Therefore, the microbes enable to survive and mobilize the As in groundwater by dissolution/bioweathering of As-minerals. Copyright © 2012. Published by Elsevier B.V.

International conference on bone mineral measurement, October 12--13, 1973, Chicago, Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1973-12-31

From international conference on bone mineral measurement; Chicago, Illinois, USA (12 Oct 1973). Abstracts of papers presented at the international conference on bone mineral measurement are presented. The papers were grouped into two sessions: a physical session including papers on measuring techniques, errors, interpretation and correlations, dual photon techniques, and data handling and exchange; a biomedical session including papers on bone disease, osteoporosis, normative data, non-disease influences, renal, and activity and inactivity. (ERB)

Interplay between black carbon and minerals contributes to long term carbon stabilization and mineral transformation

NASA Astrophysics Data System (ADS)

Liang, B.; Weng, Y. T.; Wang, C. C.; Chiang, C. C.; Liu, C. C.; Lehmann, J.

2017-12-01

Black carbon receives increasing global wide research attention due to its role in carbon sequestration, soil fertility enhancement and remediation application. Generally considered chemically stable in bulk, the reactive surface of BC can interplays with minerals and form strong chemical bondage, which renders physical protection of BC and contributes to its long term stabilization. Using historical BC-rich Amazonian Dark Earth (ADE), we probe the in-situ organo-mineral association and transformation of BC and minerals over a millennium scale using various synchrotron-based spectroscopic (XANES, FTIR) and microscopic (TXM) methods. Higher content of SRO minerals was found in BC-rich ADE compare to adjacent tropical soils. The iron signature found in BC-rich ADE was mainly ferrihydrite/lepidocrocite, a more reactive form of Fe compared to goethite, which was dominant in adjacent soil. Abundant nano minerals particles were observed in-situ associated with BC surface, in clusters and layers. The organo-mineral interaction lowers BC bioavailability and enhances its long-term stabilization in environment, while at the same time, transforms associated minerals into more reactive forms under rapid redox/weathering environment. The results suggest that mineral physical protection for BC sequestration may be more important than previous understanding. The scale up application of BC/biochar into agricultural systems and natural environments have long lasting impact on the in-situ transformation of associated minerals.

Application of the ToxMiner Database: Network Analysis ...

EPA Pesticide Factsheets

The US EPA ToxCast program is using in vitro HTS (High-Throughput Screening) methods to profile and model bioactivity of environmental chemicals. The main goals of the ToxCast program are to generate predictive signatures of toxicity, and ultimately provide rapid and cost-effective alternatives to animal testing. The chemicals selected for Phase I are composed largely by a diverse set of pesticide active ingredients, which had sufficient supporting in vivo data included as part of their registration process with the EPA. Other miscellaneous chemicals of environmental concern were also included. Application of HTS to environmental toxicants is a novel approach to predictive toxicology and health risk assessment, and differs from what is required for drug efficacy screening in that biochemical interaction of environmental chemicals are sometimes weaker than that seen with drugs and their intended targets. Additionally, the chemical space covered by environmental chemicals is much broader compared to that of pharmaceuticals. The ToxMiner database has been created and added to the EPA’s ACToR (Aggregated Computational Toxicology Resource) chemical database. One purpose of the ToxMiner database is to link biological, metabolic, and cellular pathway data to genes and in vitro assay data for the initial subset of chemicals screened in the ToxCast Phase I HTS assays. Also included in ToxMiner is human disease information, which correlates with ToxCast assays that ta

Low bone mineral density in ambulatory persons with cerebral palsy? A systematic review.

PubMed

Mus-Peters, Cindy T R; Huisstede, Bionka M A; Noten, Suzie; Hitters, Minou W M G C; van der Slot, Wilma M A; van den Berg-Emons, Rita J G

2018-05-22

Non-ambulatory persons with cerebral palsy are prone to low bone mineral density. In ambulatory persons with cerebral palsy, bone mineral density deficits are expected to be small or absent, but a consensus conclusion is lacking. In this systematic review bone mineral density in ambulatory persons with cerebral palsy (Gross Motor Function Classification Scales I-III) was studied. Medline, Embase, and Web of Science were searched. According to international guidelines, low bone mineral density was defined as Z-score ≤ -2.0. In addition, we focused on Z-score ≤ -1.0 because this may indicate a tendency towards low bone mineral density. We included 16 studies, comprising 465 patients aged 1-65 years. Moderate and conflicting evidence for low bone mineral density (Z-score ≤ -2.0) was found for several body parts (total proximal femur, total body, distal femur, lumbar spine) in children with Gross Motor Function Classification Scales II and III. We found no evidence for low bone mineral density in children with Gross Motor Function Classification Scale I or adults, although there was a tendency towards low bone mineral density (Z-score ≤ -1.0) for several body parts. Although more high-quality research is needed, results indicate that deficits in bone mineral density are not restricted to non-ambulatory people with cerebral palsy. Implications for Rehabilitation Although more high-quality research is needed, including adults and fracture risk assessment, the current study indicates that deficits in bone mineral density are not restricted to non-ambulatory people with CP. Health care professionals should be aware that optimal nutrition, supplements on indication, and an active lifestyle, preferably with weight-bearing activities, are important in ambulatory people with CP, also from a bone quality point-of-view. If indicated, medication and fall prevention training should be prescribed.

Low-Fe(III) Greenalite Was a Primary Mineral From Neoarchean Oceans

NASA Astrophysics Data System (ADS)

Johnson, Jena E.; Muhling, Janet R.; Cosmidis, Julie; Rasmussen, Birger; Templeton, Alexis S.

2018-04-01

Banded iron formations (BIFs) represent chemical precipitation from Earth's early oceans and therefore contain insights into ancient marine biogeochemistry. However, BIFs have undergone multiple episodes of alteration, making it difficult to assess the primary mineral assemblage. Nanoscale mineral inclusions from 2.5 billion year old BIFs and ferruginous cherts provide new evidence that iron silicates were primary minerals deposited from the Neoarchean ocean, contrasting sharply with current models for BIF inception. Here we used multiscale imaging and spectroscopic techniques to characterize the best preserved examples of these inclusions. Our integrated results demonstrate that these early minerals were low-Fe(III) greenalite. We present potential pathways in which low-Fe(III) greenalite could have formed through changes in saturation state and/or iron oxidation and reduction. Future constraints for ancient ocean chemistry and early life's activities should include low-Fe(III) greenalite as a primary mineral in the Neoarchean ocean.

Mineral Composition of Organically Grown Wheat Genotypes: Contribution to Daily Minerals Intake

PubMed Central

Hussain, Abrar; Larsson, Hans; Kuktaite, Ramune; Johansson, Eva

2010-01-01

In this study, 321 winter and spring wheat genotypes were analysed for twelve nutritionally important minerals (B, Cu, Fe, Se, Mg, Zn, Ca, Mn, Mo, P, S and K). Some of the genotypes used were from multiple locations and years, resulting in a total number of 493 samples. Investigated genotypes were divided into six genotype groups i.e., selections, old landraces, primitive wheat, spelt, old cultivars and cultivars. For some of the investigated minerals higher concentrations were observed in selections, primitive wheat, and old cultivars as compared to more modern wheat material, e.g., cultivars and spelt wheat. Location was found to have a significant effect on mineral concentration for all genotype groups, although for primitive wheat, genotype had a higher impact than location. Spring wheat was observed to have significantly higher values for B, Cu, Fe, Zn, Ca, S and K as compared to winter wheat. Higher levels of several minerals were observed in the present study, as compared to previous studies carried out in inorganic systems, indicating that organic conditions with suitable genotypes may enhance mineral concentration in wheat grain. This study also showed that a very high mineral concentration, close to daily requirements, can be produced by growing specific primitive wheat genotypes in an organic farming system. Thus, by selecting genotypes for further breeding, nutritional value of the wheat flour for human consumption can be improved. PMID:20948934

Secondary sulfate minerals from Alum Cave Bluff: Microscopy and microanalysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lauf, R.J.

1997-07-01

Microcrystals of secondary sulfate minerals from Alum Cave Bluff, Great Smoky Mountains National Park, were examined by scanning electron microscopy and identified by X-ray fluorescence (XRF) in the SEM. Among the samples the author discovered three new rare-earth sulfates: coskrenite-(Ce), levinsonite-(Y), and zugshunstite-(Ce). Other minerals illustrated in this report include sulfur, tschermigite, gypsum, epsomite, melanterite, halotrichite, apjohnite, jarosite, slavikite, magnesiocopiapite, and diadochite. Additional specimens whose identification is more tentative include pickeringite, aluminite, basaluminite, and botryogen. Alum Cave is a ``Dana locality`` for apjohnite and potash alum, and is the first documented North American occurrence of slavikite.

Experimental dynamic metamorphism of mineral single crystals

USGS Publications Warehouse

Kirby, S.H.; Stern, L.A.

1993-01-01

This paper is a review of some of the rich and varied interactions between non-hydrostatic stress and phase transformations or mineral reactions, drawn mainly from results of experiments done on mineral single crystals in our laboratory or our co-authors. The state of stress and inelastic deformation can enter explicitly into the equilibrium phase relations and kinetics of mineral reactions. Alternatively, phase transformations can have prominent effects on theology and on the nature of inelastic deformation. Our examples represent five types of structural phase changes, each of which is distinguished by particular mechanical effects. In increasing structural complexity, these include: (1) displacive phase transformations involving no bond-breaking, which may produce anomalous brittle behavior. A primary example is the a-?? quartz transition which shows anomalously low fracture strength and tertiary creep behavior near the transition temperature; (2) martensitic-like transformations involving transformation strains dominated by shear deformation. Examples include the orthoenstatite ??? clinoenstatite and w u ??rtzite ??? sphalerite transformations; (3) coherent exsolution or precipitation of a mineral solute from a supersaturated solid-solution, with anisotropy of precipitation and creep rates produced under nonhydrostatic stress. Examples include exsolution of corundum from MgO ?? nAl2O3 spinels and Ca-clinopyroxene from orthopyroxene; (4) order-disorder transformations that are believed to cause anomalous plastic yield strengthening, such as MgO - nAl2O3 spinels; and (5) near-surface devolatilization of hydrous silicate single-crystals that produces a fundamental brittleness thought to be connected with dehydration at microcracks at temperatures well below nominal macroscopic dehydration temperatures. As none of these interactions between single-crystal phase transformations and non-hydrostatic stress is understood in detail, this paper serves as a challenge to

Color of Minerals. Earth Science Curriculum Project Pamphlet Series PS-6.

ERIC Educational Resources Information Center

Rapp, George, Jr.

The causes for many of the colors exhibited by minerals are presented to students. Several theories of modern physics are introduced. The nature of light, the manner in which light interacts with matter, atomic theory, and crystal structure are all discussed in relation to the origin of color in minerals. Included are color pictures of many…

43 CFR 3861.3 - Mineral surveyors.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Mineral surveyors. 3861.3 Section 3861.3..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERAL PATENT APPLICATIONS Surveys and Plats § 3861.3 Mineral surveyors. ...

43 CFR 3861.3 - Mineral surveyors.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Mineral surveyors. 3861.3 Section 3861.3..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERAL PATENT APPLICATIONS Surveys and Plats § 3861.3 Mineral surveyors. ...

43 CFR 3861.3 - Mineral surveyors.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Mineral surveyors. 3861.3 Section 3861.3..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERAL PATENT APPLICATIONS Surveys and Plats § 3861.3 Mineral surveyors. ...

43 CFR 3861.3 - Mineral surveyors.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Mineral surveyors. 3861.3 Section 3861.3..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) MINERAL PATENT APPLICATIONS Surveys and Plats § 3861.3 Mineral surveyors. ...

Phosphate toxicity and vascular mineralization.

PubMed

Razzaque, Mohammed S

2013-01-01

Vascular calcification or mineralization is a major complication seen in patients with advanced stages of chronic kidney disease (CKD), and it is associated with markedly increased morbidity and mortality. Most of the CKD-related vascular mineralization is attributable to abnormal mineral ion metabolism. Elevated serum calcium and phosphate levels, along with increased calcium-phosphorus byproduct, and the use of active vitamin D metabolites are thought to be the predisposing factors for developing vascular mineralization in patients with CKD. Recent experimental studies have shown that vascular mineralization can be suppressed by reducing serum phosphate levels, even in the presence of extremely high serum calcium and 1,25-dihydroxyvitamin D levels, indicating that reducing 'phosphate toxicity' should be the important therapeutic priority in CKD patients for minimizing the risk of developing vascular mineralization and the disease progression. Copyright © 2013 S. Karger AG, Basel.

Spectroscopic characterization of manganese minerals.

PubMed

Lakshmi Reddy, S; Padma Suvarna, K; Udayabhaska Reddy, G; Endo, Tamio; Frost, R L

2014-01-03

Manganese minerals ardenite, alleghanyite and leucopoenicite originated from Madhya Pradesh, India, Nagano prefecture Japan, Sussex Country and Parker Shaft Franklin, Sussex Country, New Jersey respectively are used in the present work. In these minerals manganese is the major constituent and iron if present is in traces only. An EPR study of on all of the above samples confirms the presence of Mn(II) with g around 2.0. Optical absorption spectrum of the mineral alleghanyite indicates that Mn(II) is present in two different octahedral sites and in leucophoenicite Mn(II) is also in octahedral geometry. Ardenite mineral gives only a few Mn(II) bands. NIR results of the minerals ardenite, leucophoenicite and alleghanyite are due to hydroxyl and silicate anions which confirming the formulae of the minerals. Copyright © 2013 Elsevier B.V. All rights reserved.

Nutrition or Detoxification: Why Bats Visit Mineral Licks of the Amazonian Rainforest

PubMed Central

Voigt, Christian C.; Capps, Krista A.; Dechmann, Dina K. N.; Michener, Robert H.; Kunz, Thomas H.

2008-01-01

Many animals in the tropics of Africa, Asia and South America regularly visit so-called salt or mineral licks to consume clay or drink clay-saturated water. Whether this behavior is used to supplement diets with locally limited nutrients or to buffer the effects of toxic secondary plant compounds remains unclear. In the Amazonian rainforest, pregnant and lactating bats are frequently observed and captured at mineral licks. We measured the nitrogen isotope ratio in wing tissue of omnivorous short-tailed fruit bats, Carollia perspicillata, and in an obligate fruit-eating bat, Artibeus obscurus, captured at mineral licks and at control sites in the rainforest. Carollia perspicillata with a plant-dominated diet were more often captured at mineral licks than individuals with an insect-dominated diet, although insects were more mineral depleted than fruits. In contrast, nitrogen isotope ratios of A. obscurus did not differ between individuals captured at mineral lick versus control sites. We conclude that pregnant and lactating fruit-eating bats do not visit mineral licks principally for minerals, but instead to buffer the effects of secondary plant compounds that they ingest in large quantities during periods of high energy demand. These findings have potential implications for the role of mineral licks for mammals in general, including humans. PMID:18431492

[Mechanism of tritium persistence in porous media like clay minerals].

PubMed

Wu, Dong-Jie; Wang, Jin-Sheng; Teng, Yan-Guo; Zhang, Ke-Ni

2011-03-01

To investigate the mechanisms of tritium persistence in clay minerals, three types of clay soils (montmorillonite, kaolinite and illite) and tritiated water were used in this study to conduct the tritium sorption tests and the other related tests. Firstly, the ingredients, metal elements and heat properties of clay minerals were studied with some instrumental analysis methods, such as ICP and TG. Secondly, with a specially designed fractionation and condensation experiment, the adsorbed water, the interlayer water and the structural water in the clay minerals separated from the tritium sorption tests were fractionated for investigating the tritium distributions in the different types of adsorptive waters. Thirdly, the location and configuration of tritium adsorbed into the structure of clay minerals were studied with infrared spectrometry (IR) tests. And finally, the forces and mechanisms for driving tritium into the clay minerals were analyzed on the basis of the isotope effect of tritium and the above tests. Following conclusions have been reached: (1) The main reason for tritium persistence in clay minerals is the entrance of tritium into the adsorbed water, the interlayer water and the structural water in clay minerals. The percentage of tritium distributed in these three types of adsorptive water are in the range of 13.65% - 38.71%, 0.32% - 5.96%, 1.28% - 4.37% of the total tritium used in the corresponding test, respectively. The percentages are different for different types of clay minerals. (2) Tritium adsorbed onto clay minerals are existed in the forms of the tritiated hydroxyl radical (OT) and the tritiated water molecule (HTO). Tritium mainly exists in tritiated water molecule for adsorbed water and interlayer water, and in tritiated hydroxyl radical for structural water. (3) The forces and effects driving tritium into the clay minerals may include molecular dispersion, electric charge sorption, isotope exchange and tritium isotope effect.

Potash: a global overview of evaporate-related potash resources, including spatial databases of deposits, occurrences, and permissive tracts: Chapter S in Global mineral resource assessment

USGS Publications Warehouse

Orris, Greta J.; Cocker, Mark D.; Dunlap, Pamela; Wynn, Jeff C.; Spanski, Gregory T.; Briggs, Deborah A.; Gass, Leila; Bliss, James D.; Bolm, Karen S.; Yang, Chao; Lipin, Bruce R.; Ludington, Stephen; Miller, Robert J.; Słowakiewicz, Mirosław

2014-01-01

This report describes a global, evaporite-related potash deposits and occurrences database and a potash tracts database. Chapter 1 summarizes potash resource history and use. Chapter 2 describes a global potash deposits and occurrences database, which contains more than 900 site records. Chapter 3 describes a potash tracts database, which contains 84 tracts with geology permissive for the presence of evaporite-hosted potash resources, including areas with active evaporite-related potash production, areas with known mineralization that has not been quantified or exploited, and areas with potential for undiscovered potash resources. Chapter 4 describes geographic information system (GIS) data files that include (1) potash deposits and occurrences data, (2) potash tract data, (3) reference databases for potash deposit and tract data, and (4) representative graphics of geologic features related to potash tracts and deposits. Summary descriptive models for stratabound potash-bearing salt and halokinetic potash-bearing salt are included in appendixes A and B, respectively. A glossary of salt- and potash-related terms is contained in appendix C and a list of database abbreviations is given in appendix D. Appendix E describes GIS data files, and appendix F is a guide to using the geodatabase.

The geologic relationships of industrial mineral deposits and asbestos in the western united states

USGS Publications Warehouse

VanGosen, B.S.

2009-01-01

In recent years, U.S. regulatory agencies have placed emphasis on identifying and regulating asbestos dust exposures in the mining environment, with a particular focus upon industrial mineral deposits in which asbestos occurs as an accessory mineral. Because asbestos minerals form in specific geologic environments, only certain predictable types of industrial mineral deposits can potentially host asbestos mineralization. By applying a basic knowledge of asbestos geology, the costly and time consuming efforts of asbestos monitoring and analyses can be directed towards those mineral deposit types most likely to contain asbestos mineralogy, while saving efforts on the mineral deposits that are unlikely to contain asbestos. While the vast majority of industrial mineral deposits in the Western United States are asbestos-free, there are several types that can, in some instances, host asbestos mineralization, or be closely associated with it. These industrial mineral deposits include a few types of aggregate, dimension, and decorative stone, and some deposits of chromite-nickel, magnesite, nepheline syenite, olivine, rare earth elements, talc, vermiculite, and wollastonite.

Potential for Sulfide Mineral Deposits in Australian Waters

NASA Astrophysics Data System (ADS)

McConachy, Timothy F.

The world is witnessing a paradigm shift in relation to marine mineral resources. High-value seafloor massive sulfides at active convergent plate boundaries are attracting serious commercial attention. Under the United Nations Convention on the Law of the Sea, maritime jurisdictional zones will increase by extending over continental margins and ocean basins. For Australia, this means a possible additional 3.37 million km2 of seabed. Australia's sovereign responsibility includes, amongst other roles, the management of the exploitation of nonliving resources and sea-bed mining. What, therefore, is the potential in Australia's marine jurisdiction for similar deposits to those currently attracting commercial attention in neighboring nations and for other types/styles of sulfide deposits? A preliminary review of opportunities suggests the following: (i) volcanogenic copper—lead—zinc—silver—gold mineralization in fossil arcs and back arcs in eastern waters Norfolk Ridge and the Three Kings Ridge; (ii) Mississippi Valley-type lead—zinc—silver mineralization in the NW Shelf area; (iii) ophiolite-hosted copper mineralization in the Macquarie Ridge Complex in the Southern Ocean; and (iv) submerged extensions of prospective land-based terranes, one example being offshore Gawler Craton for iron oxide—copper—gold deposits. These areas would benefit from pre-competitive surveys of detailed swath bathymetry mapping, geophysical surveys, and sampling to help build a strategic inventory of future seafloor mineral resources for Australia.

Green Clay Minerals

NASA Astrophysics Data System (ADS)

Velde, B.

2003-12-01

Color is a problem for scientific study. One aspect is the vocabulary one used to describe color. Mint green, bottle green, and Kelly green are nice names but not of great utility in that people's physical perception of color is not always the same. In some industries, such as colored fabric manufacture, current use is to send a set of standard colors which are matched by the producer. This is similar to the use of the Munsell color charts in geology. None of these processes makes use of physical optical spectral studies. The reason is that they are difficult to obtain and interpret. For a geologist, color is very important but we rarely have the possibility to standardize the method of our color perception. One reason is that color is both a reflective and transmission phenomenon. The thickness of the sample is critical to any transmission characteristics. Hence, a field color determination is different from one made by using a petrographic microscope. Green glauconite in a hand specimen is not the same color in 30 μm thick thin section seen with a microscope using transmitted light.A second problem is that color in a spectral identification is the result of several absorption emissions,with overlapping signal, forming a complicated spectrum. Interpretation depends very greatly on the spectrum of the light source and the conditions of transmission-reflection of the sample. As a result, for this text, we will not attempt to analyze the physical aspect of green in green clays. In the discussion which follows, reference is made concerning color, to thin section microscopic perception.Very briefly, green clay minerals are green, because they contain iron. This is perhaps not a great revelation to mineralogists, but it is the key to understanding the origin and stability of green clay minerals. In fact, iron can color minerals either red or green or in various shades of orange and brown. The color most likely depends upon the relative abundance of the iron ion valence

Structure-mechanics relationships in mineralized tendons.

PubMed

Spiesz, Ewa M; Zysset, Philippe K

2015-12-01

In this paper, we review the hierarchical structure and the resulting elastic properties of mineralized tendons as obtained by various multiscale experimental and computational methods spanning from nano- to macroscale. The mechanical properties of mineralized collagen fibres are important to understand the mechanics of hard tissues constituted by complex arrangements of these fibres, like in human lamellar bone. The uniaxial mineralized collagen fibre array naturally occurring in avian tendons is a well studied model tissue for investigating various stages of tissue mineralization and the corresponding elastic properties. Some avian tendons mineralize with maturation, which results in a graded structure containing two zones of distinct morphology, circumferential and interstitial. These zones exhibit different amounts of mineral, collagen, pores and a different mineral distribution between collagen fibrillar and extrafibrillar space that lead to distinct elastic properties. Mineralized tendon cells have two phenotypes: elongated tenocytes placed between fibres in the circumferential zone and cuboidal cells with lower aspect ratios in the interstitial zone. Interestingly some regions of avian tendons seem to be predestined to mineralization, which is exhibited as specific collagen cross-linking patterns as well as distribution of minor tendon constituents (like proteoglycans) and loss of collagen crimp. Results of investigations in naturally mineralizing avian tendons may be useful in understanding the pathological mineralization occurring in some human tendons. Copyright © 2015 Elsevier Ltd. All rights reserved.

Geology, Geochemistry, Geophysics, Mineral Occurrences and Mineral Resource Assessment for the Commonwealth of Puerto Rico

USGS Publications Warehouse

Bawiec, Walter J.

1998-01-01

The Commonwealth of Puerto Rico has been investigated over a very long period of time by earth scientists from many disciplines and with diverse objectives in the studies. This publication attempts to apply much of the geologic, geochemical, geophysical, and mineral occurrence information to a single objective focused on producing a mineral resource assessment for the Commonwealth of Puerto Rico. However, the value of this publication lies not within the results of the mineral resource assessment nor within the interactive PDF files which can be viewed on the screen, but within the geologic, geochemical, geophysical, and mineral occurrence digital map coverages and databases which can be used for their own unique applications. The mineral resource assessment of Puerto Rico represents compilation of several decades of mineral investigations and studies. These investigations have been the joint efforts of the U.S. Geological Survey, the Puerto Rico Department of Natural Resources, and the University of Puerto Rico. This report contains not only the mineral-resource assessment, but also much of the scientific evidence upon which the assessment was based.

43 CFR 3830.10 - Locatable minerals.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false Locatable minerals. 3830.10 Section 3830..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LOCATING, RECORDING, AND MAINTAINING MINING CLAIMS OR SITES; GENERAL PROVISIONS Mining Law Minerals § 3830.10 Locatable minerals. ...

43 CFR 3830.10 - Locatable minerals.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false Locatable minerals. 3830.10 Section 3830..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LOCATING, RECORDING, AND MAINTAINING MINING CLAIMS OR SITES; GENERAL PROVISIONS Mining Law Minerals § 3830.10 Locatable minerals. ...

43 CFR 3830.10 - Locatable minerals.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Locatable minerals. 3830.10 Section 3830..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LOCATING, RECORDING, AND MAINTAINING MINING CLAIMS OR SITES; GENERAL PROVISIONS Mining Law Minerals § 3830.10 Locatable minerals. ...

43 CFR 3830.10 - Locatable minerals.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false Locatable minerals. 3830.10 Section 3830..., DEPARTMENT OF THE INTERIOR MINERALS MANAGEMENT (3000) LOCATING, RECORDING, AND MAINTAINING MINING CLAIMS OR SITES; GENERAL PROVISIONS Mining Law Minerals § 3830.10 Locatable minerals. ...

Dust from mineral extraction: regulation of emissions in England

NASA Astrophysics Data System (ADS)

Marker, Brian

2013-04-01

The United Kingdom, which includes England, has fairly high levels of rainfall but sporadic droughts occur especially in the east. Mineral working gives rise to dust. Concerns about dust soiling are major source of public objections to new minerals extraction operations. Dust emissions from mineral workings are a significant cause of public concern in the United Kingdom and are recognised as sources of health concerns and nuisance. Emissions are controlled through a number of complementary sets of regulations that are generally well observed by the industry and well enforced by the relevant public authorities. comprehensive system of regulation, based on European and national law, to deal with all aspects of these operations including pollution control, planning, occupational health and safety and statutory nuisances. Most minerals applications are subject to EIA which forms that basis for planning and environmental conditions and monitoring of operations. There are limit values on PM10 and PM2.5 in air, and for potentially harmful elements (PHEs) in soils and water, derived from European regulations but, as yet, no limit values for PHEs (other than radioactive materials) in air. Stakeholder engagement is encouraged so that members of the public can express concerns during minerals operations and operators can quickly deal with these. While some effects inevitably remain, the levels of dust emissions are kept low through good site design and management, proper use of machinery which is equipped to minimise emissions, and good training of the workforce. Operational sites are required to have dust monitoring equipment located outside the site boundary so that any emerging problems can be detected and addressed quickly.

The Impact of Organo-Mineral Complexation on Mineral Weathering in the Soil Zone under Unsaturated Conditions

NASA Astrophysics Data System (ADS)

Michael, H. A.; Tan, F.; Yoo, K.; Imhoff, P. T.

2017-12-01

While organo-mineral complexes can protect organic matter (OM) from biodegradation, their impact on soil mineral weathering is not clear. Previous bench-scale experiments that focused on specific OM and minerals showed that the adsorption of OM to mineral surfaces accelerates the dissolution of some minerals. However, the impact of natural organo-mineral complexes on mineral dissolution under unsaturated conditions is not well known. In this study, soil samples prepared from an undisturbed forest site were used to determine mineral weathering rates under differing conditions of OM sorption to minerals. Two types of soil samples were generated: 1) soil with OM (C horizon soil from 84-100cm depth), and 2) soil without OM (the same soil as in 1) but with OM removed by heating to 350°for 24 h). Soil samples were column-packed and subjected to intermittent infiltration and drainage to mimic natural rainfall events. Each soil sample type was run in duplicate. The unsaturated condition was created by applying gas pressure to the column, and the unsaturated chemical weathering rates during each cycle were calculated from the effluent concentrations. During a single cycle, when applying the same gas pressure, soils with OM retained more moisture than OM-removed media, indicating increased water retention capacity under the impact of OM. This is consistent with the water retention data measured by evaporation experiments (HYPROP) and the dew point method (WP4C Potential Meter). Correspondingly, silicon (Si) denudation rates indicated that dissolution of silicate minerals was 2-4 times higher in OM soils, suggesting that organo-mineral complexes accelerate mineral dissolution under unsaturated conditions. When combining data from all cycles, the results showed that Si denudation rates were positively related to soil water content: denundation rate increased with increasing water content. Therefore, natural mineral chemical weathering under unsaturated conditions, while

30 CFR 48.26 - Experienced miner training.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING... observed and explained. (2) Mandatory health and safety standards. The course shall include the mandatory health and safety standards pertinent to the tasks to be assigned. (3) Authority and responsibility of...

30 CFR 48.26 - Experienced miner training.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING... observed and explained. (2) Mandatory health and safety standards. The course shall include the mandatory health and safety standards pertinent to the tasks to be assigned. (3) Authority and responsibility of...

Glycine Polymerization on Oxide Minerals.

PubMed

Kitadai, Norio; Oonishi, Hiroyuki; Umemoto, Koichiro; Usui, Tomohiro; Fukushi, Keisuke; Nakashima, Satoru

2017-06-01

It has long been suggested that mineral surfaces played an important role in peptide bond formation on the primitive Earth. However, it remains unclear which mineral species was key to the prebiotic processes. This is because great discrepancies exist among the reported catalytic efficiencies of minerals for amino acid polymerizations, owing to mutually different experimental conditions. This study examined polymerization of glycine (Gly) on nine oxide minerals (amorphous silica, quartz, α-alumina and γ-alumina, anatase, rutile, hematite, magnetite, and forsterite) using identical preparation, heating, and analytical procedures. Results showed that a rutile surface is the most effective site for Gly polymerization in terms of both amounts and lengths of Gly polymers synthesized. The catalytic efficiency decreased as rutile > anatase > γ-alumina > forsterite > α- alumina > magnetite > hematite > quartz > amorphous silica. Based on reported molecular-level information for adsorption of Gly on these minerals, polymerization activation was inferred to have arisen from deprotonation of the NH 3 + group of adsorbed Gly to the nucleophilic NH 2 group, and from withdrawal of electron density from the carboxyl carbon to the surface metal ions. The orientation of adsorbed Gly on minerals is also a factor influencing the Gly reactivity. The examination of Gly-mineral interactions under identical experimental conditions has enabled the direct comparison of various minerals' catalytic efficiencies and has made discussion of polymerization mechanisms and their relative influences possible Further systematic investigations using the approach reported herein (which are expected to be fruitful) combined with future microscopic surface analyses will elucidate the role of minerals in the process of abiotic peptide bond formation.

Mineral induction by immobilized phosphoproteins

NASA Technical Reports Server (NTRS)

Saito, T.; Arsenault, A. L.; Yamauchi, M.; Kuboki, Y.; Crenshaw, M. A.

1997-01-01

Dentin phosphoproteins are thought to have a primary role in the deposition of mineral on the collagen of dentin. In this study we determined the type of binding between collagen and phosphoproteins necessary for mineral formation onto collagen fibrils and whether the phosphate esters are required. Bovine dentin phosphophoryn or phosvitin from egg yolk were immobilized on reconstituted skin type I collagen fibrils by adsorption or by covalent cross-linking. In some samples the ester phosphate was removed from the covalently cross-linked phosphoproteins by treatment with acid phosphatase. All samples were incubated at 37 degrees C in metastable solutions that do not spontaneously precipitate. Reconstituted collagen fibrils alone did not induce mineral formation. The phosphoproteins adsorbed to the collagen fibrils desorbed when the mineralization medium was added, and mineral was not induced. The mineral induced by the cross-linked phosphoproteins was apatite, and the crystals were confined to the surface of the collagen fibrils. With decreasing medium saturation the time required for mineral induction increased. The interfacial tensions calculated for apatite formation by either phosphoprotein cross-linked to collagen were about the same as that for phosphatidic acid liposomes and hydroxyapatite. This similarity in values indicates that the nucleation potential of these highly phosphorylated surfaces is about the same. It is concluded that phosphoproteins must be irreversibly bound to collagen fibrils for the mineralization of the collagen network in solutions that do not spontaneously precipitate. The phosphate esters of phosphoproteins are required for mineral induction, and the carboxylate groups are not sufficient.

Mineralogical, Chemical, and Optical Interrelationships of Airborne Mineral Dusts

NASA Astrophysics Data System (ADS)

Engelbrecht, J. P.; Moosmuller, H.; Pincock, S. L.; Jayanty, R. K. M.; Casuccio, G.

2014-12-01

The purpose of the project was to provide information on the mineralogical, chemical and physical interrelationships of re-suspended mineral dust samples collected as grab samples from global dust sources. Surface soil samples were collected from about 65 desert sites, including the southwestern USA (12), Mali (3), Chad (3), Morocco (1), Canary Islands (8), Cape Verde (1), Djibouti (1), Afghanistan (3), Iraq (6), Kuwait (5), Qatar (1), UAE (1), Serbia (3), China (5), Namibia (3), Botswana (4), Australia (3), and Chile (1). The < 38 μm sieved fraction of each sample was re-suspended in an entrainment chamber, from which the airborne mineral dust could be monitored, sampled and analyzed. Instruments integrated into the entrainment facility included two PM10 and two PM2.5 filter samplers, a beta attenuation gauge for the continuous measurement of PM10 and PM2.5 particulate mass fractions, an aerodynamic particle size (APS) analyzer, and a three wavelength (405, 532, 781nm) photoacoustic resonator with integrating reciprocal nephelometer for monitoring absorption and scattering coefficients during the dust re-suspension process. Filter sample media included Teflon® membrane and quartz fiber filters for chemical analysis (71 species), and Nuclepore® filters for individual particle analysis by Scanning Electron Microscopy (SEM). The < 38 μm sieved fractions were also analyzed by X-ray diffraction for their mineral content while the > 38 μm, < 125 μm soil fractions were mineralogically characterized by optical microscopy. We will be presenting results on the optical measurements, also showing the relationship between single scattering albedo (SSA) at three different wavelengths, and chemical as well as mineralogical content and interdependencies of the entrained dust samples. Examples showing the relationships between the single scattering albedos of airborne dusts, and iron (Fe) in hematite, goethite, and clay minerals (montmorillonite, illite, palygorskite), will

Phospholipases of Mineralization Competent Cells and Matrix Vesicles: Roles in Physiological and Pathological Mineralizations

PubMed Central

Mebarek, Saida; Abousalham, Abdelkarim; Magne, David; Do, Le Duy; Bandorowicz-Pikula, Joanna; Pikula, Slawomir; Buchet, René

2013-01-01

The present review aims to systematically and critically analyze the current knowledge on phospholipases and their role in physiological and pathological mineralization undertaken by mineralization competent cells. Cellular lipid metabolism plays an important role in biological mineralization. The physiological mechanisms of mineralization are likely to take place in tissues other than in bones and teeth under specific pathological conditions. For instance, vascular calcification in arteries of patients with renal failure, diabetes mellitus or atherosclerosis recapitulates the mechanisms of bone formation. Osteoporosis—a bone resorbing disease—and rheumatoid arthritis originating from the inflammation in the synovium are also affected by cellular lipid metabolism. The focus is on the lipid metabolism due to the effects of dietary lipids on bone health. These and other phenomena indicate that phospholipases may participate in bone remodelling as evidenced by their expression in smooth muscle cells, in bone forming osteoblasts, chondrocytes and in bone resorbing osteoclasts. Among various enzymes involved, phospholipases A1 or A2, phospholipase C, phospholipase D, autotaxin and sphingomyelinase are engaged in membrane lipid remodelling during early stages of mineralization and cell maturation in mineralization-competent cells. Numerous experimental evidences suggested that phospholipases exert their action at various stages of mineralization by affecting intracellular signaling and cell differentiation. The lipid metabolites—such as arachidonic acid, lysophospholipids, and sphingosine-1-phosphate are involved in cell signaling and inflammation reactions. Phospholipases are also important members of the cellular machinery engaged in matrix vesicle (MV) biogenesis and exocytosis. They may favour mineral formation inside MVs, may catalyse MV membrane breakdown necessary for the release of mineral deposits into extracellular matrix (ECM), or participate in

43 CFR 3602.33 - How will BLM dispose of mineral materials for use in developing Federal mineral leases?

Code of Federal Regulations, 2014 CFR

2014-10-01

... 43 Public Lands: Interior 2 2014-10-01 2014-10-01 false How will BLM dispose of mineral materials for use in developing Federal mineral leases? 3602.33 Section 3602.33 Public Lands: Interior... MINERALS MANAGEMENT (3000) MINERAL MATERIALS DISPOSAL Mineral Materials Sales Noncompetitive Sales § 3602...

43 CFR 3602.33 - How will BLM dispose of mineral materials for use in developing Federal mineral leases?

Code of Federal Regulations, 2012 CFR

2012-10-01

... 43 Public Lands: Interior 2 2012-10-01 2012-10-01 false How will BLM dispose of mineral materials for use in developing Federal mineral leases? 3602.33 Section 3602.33 Public Lands: Interior... MINERALS MANAGEMENT (3000) MINERAL MATERIALS DISPOSAL Mineral Materials Sales Noncompetitive Sales § 3602...

43 CFR 3602.33 - How will BLM dispose of mineral materials for use in developing Federal mineral leases?

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false How will BLM dispose of mineral materials for use in developing Federal mineral leases? 3602.33 Section 3602.33 Public Lands: Interior... MINERALS MANAGEMENT (3000) MINERAL MATERIALS DISPOSAL Mineral Materials Sales Noncompetitive Sales § 3602...

43 CFR 3602.33 - How will BLM dispose of mineral materials for use in developing Federal mineral leases?

Code of Federal Regulations, 2013 CFR

2013-10-01

... 43 Public Lands: Interior 2 2013-10-01 2013-10-01 false How will BLM dispose of mineral materials for use in developing Federal mineral leases? 3602.33 Section 3602.33 Public Lands: Interior... MINERALS MANAGEMENT (3000) MINERAL MATERIALS DISPOSAL Mineral Materials Sales Noncompetitive Sales § 3602...

Remote sensing of geologic mineral occurrences for the Colorado mineral belt using LANDSAT data

NASA Technical Reports Server (NTRS)

Carpenter, R. H. (Principal Investigator); Trexler, D. W.

1976-01-01

The author has identified the following significant results. LANDSAT imagery was examined as a practical and productive tool for mineral exploration along the Colorado Mineral Belt. An attempt was made to identify all large, active and/or abandoned mining districts on the imagery which initially were discovered by surface manifestations. A number of strong photolinements, circular features, and color anomalies were identified. Some of these form a part of the structural and igneous volcanic framework in which mineral deposits occur. No specific mineral deposits such as veins or porphyries were identified. Promising linear and concentric features were field checked at several locations. Some proved to be fault zones and calderas; others were strictly topographic features related to stream or glacial entrenchment. The Silverton Caldera region and the Idaho Springs-Central City district were chosen and studied as case histories to evaluate the application of LANDSAT imagery to mineral exploration. Evidence of specific mineralization related to ore deposits in these two areas were observed only on low level photography.

CellMiner Companion: an interactive web application to explore CellMiner NCI-60 data.

PubMed

Wang, Sufang; Gribskov, Michael; Hazbun, Tony R; Pascuzzi, Pete E

2016-08-01

The NCI-60 human tumor cell line panel is an invaluable resource for cancer researchers, providing drug sensitivity, molecular and phenotypic data for a range of cancer types. CellMiner is a web resource that provides tools for the acquisition and analysis of quality-controlled NCI-60 data. CellMiner supports queries of up to 150 drugs or genes, but the output is an Excel file for each drug or gene. This output format makes it difficult for researchers to explore the data from large queries. CellMiner Companion is a web application that facilitates the exploration and visualization of output from CellMiner, further increasing the accessibility of NCI-60 data. The web application is freely accessible at https://pul-bioinformatics.shinyapps.io/CellMinerCompanion The R source code can be downloaded at https://github.com/pepascuzzi/CellMinerCompanion.git ppascuzz@purdue.edu Supplementary data are available at Bioinformatics online. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Potential mineral resources, Payette National Forest, Idaho: description and probabilistic estimation

USGS Publications Warehouse

Bookstrom, Arthur A.; Johnson, Bruce R.; Cookro, Theresa M.; Lund, Karen; Watts, Kenneth C.; King, Harley D.; Kleinkopf, Merlin D.; Pitkin, James A.; Sanchez, J. David; Causey, J. Douglas

1998-01-01

The Payette National Forest (PNF), in west-central Idaho, is geologically diverse and contains a wide variety of mineral resources. Mineral deposit types are grouped into locatable, leasable, and salable categories. The PNF has substantial past production and identified resources of locatable commodities, including gold, silver, copper, zinc, tungsten, antimony, mercury, and opal. Minor lignitic coal is the only leasable mineral resource known to be present in the PNF. Resources of salable commodities in the PNF include sand-and-gravel, basalt for crushed-rock aggregate, and minor gypsum. Locatable mineral resources are geographically divided between eastern and western parts of the PNF. The western PNF lies west of the Riggins-to-Cascade highway (US 95 - Idaho 55), and the eastern PNF is east of that highway. The western and eastern parts of the PNF are geologically distinctive and have different types of locatable mineral deposits, so their locatable mineral resources are described separately. Within the western and eastern parts of the PNF, locatable deposit types generally are described in order of decreasing geologic age. An expert panel delineated tracts considered geologically permissive and (or) favorable for the occurrence of undiscovered mineral deposits of types that are known to be present within or near the PNF. The panel also estimated probabilities for undiscovered deposits, and used numerical simulation, based on tonnage-grade distribution models, to derive estimates of in-situ metals contained. These estimates are summarized in terms of mean and median measures of central tendency. Most grade and tonnage distributions appear to be log-normal, with the median lower than the mean. Inasmuch as the mean is influenced by the largest deposits in the model tonnage-grade distribution, the median provides a lower measure of central tendency and a more conservative estimation of undiscovered resources.

Design of exploration and minerals-data-collection programs in developing areas

USGS Publications Warehouse

Attanasi, E.D.

1981-01-01

This paper considers the practical problem of applying economic analysis to designing minerals exploration and data collection strategies for developing countries. Formal decision rules for the design of government exploration and minerals-data-collection programs are derived by using a minerals-industry planning model that has been extended to include an exploration function. Rules derived are applicable to centrally planned minerals industries as well as market-oriented minerals sectors. They pertain to the spatial allocation of exploration effort and to the allocation of activities between government and private concerns for market-oriented economies. Programs characterized by uniform expenditures, uniform information coverage across regions, or uniform-density grid drilling progrmas are shown to be inferior to the strategy derived. Moreover, for market-oriented economies, the economically optimal mix in exploration activities between private and government data collection would require that only private firms assess local sites and that government agencies carry out regional surveys. ?? 1981.

Fostering Minerals Workforce Skills of Tomorrow through Education and Training Partnerships

NASA Astrophysics Data System (ADS)

Lind, Gavin

The Minerals Council of Australia (MCA), through its Minerals Tertiary Education Council (MTEC), builds capacity in higher education in the core disciplines of mining engineering, metallurgy and minerals geoscience. Over the past fourteen years, this all-of-industry approach in securing the long-term supply of these critical skills (which remain a chronic skills shortage for the Australian minerals industry) through nationally collaborative programs across sixteen Australian universities delivers spectacular and sustainable results for the industry. These unique, world-first programs are built on a healthy platform of dedicated industry funding and in-kind support and forms part of the MCA's broader uninterrupted, sustainable education and training pathway to increase workforce participation, workforce diversity and workforce skills, regardless of the business cycle in the industry. This paper will highlight the origins, iterations and current successful programs of MTEC, including its future vision, and presents a mechanism for industry and academia to collaborate to address future professional skills needs in the minerals industry globally.

Hydrothermal and Diagenetic Mineralization on Mars

NASA Astrophysics Data System (ADS)

Ehlmann, B. L.; Quinn, D. P.

2015-12-01

Predicted by geophysical modeling, the mineraolgic record of early Mars groundwater has only recently been discovered. First, rover exploration in sedimentary basins reveals diagenesis. At Meridiani, sandstone porosity is occluded by precipitation of secondary sulfates, hematite, and silica. Multiple alteration episodes are indicated by crystal vugs, disruption of preexisting textures by hematite concretions, and grain coatings (e.g. McLennan et al., 2005). At Gale crater, raised ridges in mudstones, interpreted to be early diagenetic features, are crossed by later-emplaced hydrated calcium sulfate veins (e.g. Grotzinger et al., 2014). Waters in Gale were likely circumneutral while jarosite mineralogy at Meridiani implies acidic waters. Second, systems of raised ridges at 100-m scale are observed from orbit in multiple Martian sedimentary rock units. An outstanding example is sulfate-bearing sediments exhumed at the northern margin of the Syrtis Major lavas (e.g. Quinn & Ehlmann, 2015). Polygonal and with no clearly preferred orientation, the ridges rise 5-30 m above the surrounding terrain. Parallel light-toned grooves with dark interiors (indicative of isopachous fills) and jarosite in ridge mineralogy point to mineralization by acidic waters. Third, some mineral assemblages observed from orbit represent the products of subsurface aqueous alteration at elevated temperatures (Ehlmann et al., 2011). These are globally distributed, exposed in scarps and by impact cratering. Mineral assemblages variously include (a) serpentine and carbonate; (b) prehnite and chlorite, and (c) zeolites. Collectively, these datasets indicate that groundwaters were spatially widespread on ancient Mars, contributing to the sustenance of lakes and to the alteration of bedrock to >1 km depths. While the Martian surface may have always been relatively inhospitable, a warmer, wetter subsurface provided a long-term potentially habitable environment. Key outstanding questions remaining include

Identification and significance of accessory minerals from a bituminous coal

USGS Publications Warehouse

Finkelman, R.B.; Stanton, R.W.

1978-01-01

A scanning electron microscope (SEM) has been used to study the in situ accessory minerals in polished blocks and pellets of petrographically analysed samples of the Waynesburg coal (hvb). Individual grains from the low-temperature ash (LTA) of the same coal were also studied. The visual resolution of the SEM permitted the detection of submicron mineral grains, which could then be analysed by the attached energy-dispersive system. Emphasis was placed on the highly reflective grains in the carbominerite bands. Among the most abundant accessory minerals observed were rutile, zircon, and rare-earth-bearing minerals. Small (1-5 ??m) particles of what may be authigenic iron-rich chromite and a nickel silicate form rims on quartz grains. The SEM also permits the observation of grain morphology and mineral intergrowths. These data are useful in determining authigenicity and diagenic alteration. Substances in density splits of LTA include authigenic, detrital, extraterrestrial magnetite, tourmaline, and evaporite (?) minerals, and a fluorine-bearing amphibole. This analytical approach allows the determination of specific sites for many of the trace elements in coals. In the Waynesburg coal, most of the chromium is in the iron-chromium rims, the fluorine is in the amphibole, and the rare-earth elements are in rare-earth-bearing minerals. The ability to relate trace-element data to specific minerals will aid in predicting the behaviour of elements in coal during combustion, liquefaction, gasification, weathering, and leaching processes. This ability also permits insight into the degree of mobility of these elements in coal and provides clues to sedimentological and diagenetic conditions. ?? 1978.

Some implications of changing patterns of mineral consumption

USGS Publications Warehouse

Menzie, W. David; DeYoung,, John H.; Steblez, Walter G.

2003-01-01

DeYoung and Menzie (1999) examined the relations among population, Gross Domestic Product, and mineral consumption (aluminum, cement, copper, and salt) for Japan, Korea, and the United States between 1965 and 1995. They noted the extremely rapid growth of consumption in Korea between 1975 and 1995. Concomitantly, Korea's population growth rate declined. This paper extends that earlier work by examining patterns of consumption of these same commodities in the twenty most populous countries for the period 1970 through 1995. Developed countries, such as France, Germany, Japan, the United Kingdom, and the United States, show patterns of consumption that are stable (cement, copper, and salt) or grow slowly (aluminum). Some developing countries, including China, Thailand, and Turkey, show more rapid growth of consumption, especially of cement, copper, and aluminum. These changing patterns of mineral consumption in developing countries have important implications -- if they continue, there could be major increases in world mineral consumption and major increases in environmental residuals from mineral production and use. If China reaches the level of consumption of copper of developed countries, world consumption could reach levels more than twice that of 1995 (10.5 million tons).

Studies of matrix vesicle-induced mineralization in a gelatin gel

NASA Technical Reports Server (NTRS)

Boskey, A. L.; Boyan, B. D.; Doty, S. B.; Feliciano, A.; Greer, K.; Weiland, D.; Swain, L. D.; Schwartz, Z.

1992-01-01

Matrix vesicles isolated from fourth-passage cultures of chondrocytes were tested for their ability to induce hydroxyapatite formation in a gelatin gel in order to gain insight into the function of matrix vesicles in in situ mineralization. These matrix vesicles did not appear to be hydroxyapatite nucleators per se since the extent of mineral accumulation in the gel diffusion system was not altered by the presence of matrix vesicles alone, and in the vesicle containing gels, mineral crystals were formed whether associated with vesicles or not. In gels with these matrix vesicles and beta-glycerophosphate, despite the presence of alkaline phosphatase activity, there was no increase in mineral deposition. This suggested that in the gel system these culture-derived vesicles did not increase local phosphate concentrations. However, when known inhibitors of mineral crystal formation and growth (proteoglycan aggregates [4 mg/ml], or ATP [1 mM], or both proteoglycan and ATP) were included in the gel, more mineral was deposited in gels with the vesicles than in comparable gels without vesicles, indicating that enzymes within these vesicles were functioning to remove the inhibition. These data support the suggestion that one function of the extracellular matrix vesicles is to transport enzymes for matrix modification.

In situ evidence of mineral physical protection and carbon stabilization revealed by nanoscale 3-D tomography

NASA Astrophysics Data System (ADS)

Weng, Yi-Tse; Wang, Chun-Chieh; Chiang, Cheng-Cheng; Tsai, Heng; Song, Yen-Fang; Huang, Shiuh-Tsuen; Liang, Biqing

2018-05-01

An approach for nanoscale 3-D tomography of organic carbon (OC) and associated mineral nanoparticles was developed to illustrate their spatial distribution and boundary interplay, using synchrotron-based transmission X-ray microscopy (TXM). The proposed 3-D tomography technique was first applied to in situ observation of a laboratory-made consortium of black carbon (BC) and nanomineral (TiO2, 15 nm), and its performance was evaluated using dual-scan (absorption contrast and phase contrast) modes. This novel tool was then successfully applied to a natural OC-mineral consortium from mountain soil at a spatial resolution of 60 nm, showing the fine structure and boundary of OC, the distribution of abundant nano-sized minerals, and the 3-D organo-mineral association in situ. The stabilization of 3500-year-old natural OC was mainly attributed to the physical protection of nano-sized iron (Fe)-containing minerals (Fe oxyhydroxides including ferrihydrite, goethite, and lepidocrocite), and the strong organo-mineral complexation. In situ evidence revealed an abundance of mineral nanoparticles, in dense thin layers or nano-aggregates/clusters, instead of crystalline clay-sized minerals on or near OC surfaces. The key working minerals for C stabilization were reactive short-range-order (SRO) mineral nanoparticles and poorly crystalline submicron-sized clay minerals. Spectroscopic analyses demonstrated that the studied OC was not merely in crisscross co-localization with reactive SRO minerals; there could be a significant degree of binding between OC and the minerals. The ubiquity and abundance of mineral nanoparticles on the OC surface, and their heterogeneity in the natural environment may have been severely underestimated by traditional research approaches. Our in situ description of organo-mineral interplay at the nanoscale provides direct evidence to substantiate the importance of mineral physical protection for the long-term stabilization of OC. This high-resolution 3-D

Gold-bearing skarns

USGS Publications Warehouse

Theodore, Ted G.; Orris, Greta J.; Hammerstrom, Jane M.; Bliss, James D.

1991-01-01

In recent years, a significant proportion of the mining industry's interest has been centered on discovery of gold deposits; this includes discovery of additional deposits where gold occurs in skarn, such as at Fortitude, Nevada, and at Red Dome, Australia. Under the classification of Au-bearing skarns, we have modeled these and similar gold-rich deposits that have a gold grade of at least 1 g/t and exhibit distinctive skarn mineralogy. Two subtypes, Au-skarns and byproduct Au-skarns, can be recognized on the basis of gold, silver, and base-metal grades, although many other geological factors apparently are still undistinguishable largely because of a lack of detailed studies of the Au-skarns. Median grades and tonnage for 40 Au-skarn deposits are 8.6 g/t Au, 5.0 g/t Ag, and 213,000 t. Median grades and tonnage for 50 byproduct and Au-skarn deposits are 3.7 g/t Au, 37 g/t Ag, and 330,000 t. Gold-bearing skarns are generally calcic exoskarns associated with intense retrograde hydrosilicate alteration. These skarns may contain economic amounts of numerous other commodities (Cu, Fe, Pb, Zn, As, Bi, W, Sb, Co, Cd, and S) as well as gold and silver. Most Au-bearing skarns are found in Paleozoic and Cenozoic orogenic-belt and island-arc settings and are associated with felsic to intermediate intrusive rocks of Paleozoic to Tertiary age. Native gold, electru, pyrite, pyrrhotite, chalcopyrite, arsenopyrite, sphalerite, galena, bismuth minerals, and magnetite or hematite are the most common opaque minerals. Gangue minerals typically include garnet (andradite-grossular), pyroxene (diopside-hedenbergite), wollastonite, chlorite, epidote, quartz, actinolite-tremolite, and (or) calcite.

Impact of mineral fertility and bedrock erosion on single-mineral detrital studies: insights from trace-element and Nd-isotope systematics of detrital apatite from the Po River catchment

NASA Astrophysics Data System (ADS)

Malusa', Marco Giovanni; Wang, Jiangang; Garzanti, Eduardo; Villa, Igor M.; Wittman, Hella

2017-04-01

The detrital record provides an archive of mountain erosion that preserves key information for paleotectonic and paleoclimatic reconstructions. Detrital studies are often based on single-mineral analyses (e.g., geo/thermochronologic analyses on apatite and zircon). Their geologic interpretation can be challenging, because the impact of each eroding source on the detrital record is controlled by a range of factors including the rate of erosion and the fertility of chosen minerals in eroded bedrock. Here, we combine (i) a state-of-the art dataset of trace element and Nd isotope fingerprints of detrital apatite, (ii) a comprehensive dataset of apatite-fertility measurements (Malusà et al. 2016), (iii) fission-track data, and (iv) cosmogenic-derived erosion rates from the Po River catchment (Wittmann et al. 2016), to test the impact of mineral fertility and bedrock erosion on the single-mineral detrital signal preserved in the final sediment sink. Our results show that the information provided by accessory minerals, when complemented with accurate mineral fertility measurements, are fully consistent with information provided by the analysis of more abundant framework minerals. We found that trace element and Nd isotope analyses provide a reliable tool to disentangle the complex single-mineral record of orogenic erosion, and demonstrate that such a record is largely determined by high-fertility source rocks exposed within the drainage. Detrital thermochronology studies based on the lag-time approach should thus preferably include independent provenance discriminations and a full mineral fertility characterization of the potential source areas, in order to ensure a correct identification of the sediment sources and of the exogenic and endogenic processes monitored in the stratigraphic archive. Malusà M.G., Resentini A., Garzanti E., 2016. Hydraulic sorting and mineral fertility bias in detrital geochronology. Gondwana Res., 31, 1-19 Wittmann H., Malusà M.G., Resentini

Mineralization of Carbon Dioxide: Literature Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romanov, V; Soong, Y; Carney, C

2015-01-01

CCS research has been focused on CO2 storage in geologic formations, with many potential risks. An alternative to conventional geologic storage is carbon mineralization, where CO2 is reacted with metal cations to form carbonate minerals. Mineralization methods can be broadly divided into two categories: in situ and ex situ. In situ mineralization, or mineral trapping, is a component of underground geologic sequestration, in which a portion of the injected CO2 reacts with alkaline rock present in the target formation to form solid carbonate species. In ex situ mineralization, the carbonation reaction occurs above ground, within a separate reactor or industrialmore » process. This literature review is meant to provide an update on the current status of research on CO2 mineralization. 2« less

Mineralogical variation of skarn ore from the Tellerhäuser deposit, Pöhla, Germany

NASA Astrophysics Data System (ADS)

Simons, Bethany; Andersen, Jens Christian; Rollinson, Gavyn; Armstrong, Robin; Dolgopolova, Alla; Seltmann, Reimar; Stanley, Chris; Roscher, Marco

2017-04-01

The polymetallic Zn-Fe-Sn-Cu-In skarns at Pöhla Tellerhäuser in the western Erzgebirge represent some of the largest unexploited occurrences of Sn and In in Europe. The skarns developed in schists and gneisses at the margin of the Schwarzenberg Gneiss cupola and the Eibenstock granites. The flat-lying skarn layers display extreme mineralogical variability with alternating units of pyroxene, sphalerite, magnetite, amphibole and calc-silicate skarns with hanging wall schist and feeder stockwork. The polymetallic skarn ores represent a complex challenge for mineral processing, with fine-grained, locked target minerals and partitioning of target metals into silicates (e.g. Sn in malayaite). Optical microscopy, QEMSCAN® and electron-probe microanalysis have been used to determine the mineralogical variability of the skarn types with the aim to determine the deportment of the target metals to guide mineral processing test work. The composition of the skarns is extremely variable reflecting the complex mineralogy and indicating substantial variability associated with replacement reactions through the protolith(s). Cassiterite (SnO2) is the dominant Sn-bearing mineral in all the skarn types. However, the skarns also carry malayaite (CaSnO[SiO4], up to 0.03 vol%), which locally dominates over cassiterite. Cassiterite is intergrown with Fe-amphibole, grossular garnet, fluorite and magnetite. The cassiterite is unaltered, but some grains have rare iron oxide rims and inclusions. Malayaite shows a similar association to cassiterite and is intergrown as clusters of grains with silicate gangue, particularly Fe amphibole and grossular garnet and remains unaltered with no inclusions. Zinc is exclusively hosted in sphalerite and varies from 0.02 wt.% in the hanging wall schist to 36.5 wt.% in the sphalerite skarn. The high Zn values are accompanied by high values of Cd (locally in excess of 1000 ppm) and In (up to 180 ppm). Sphalerite grains are locally up to 4 mm, subhedral

Mineral Potential Mapping in a Frontier Region

NASA Astrophysics Data System (ADS)

Ford, A.

2009-04-01

Mineral potential mapping using Geographic Information Systems (GIS) allows for rapid evaluation of spatial geoscience data and has the potential to delineate areas which may be prospective for hosting mineral deposits. Popular methods for evaluating digital data include weights of evidence, fuzzy logic and probabilistic neural networks. To date, such methods have been mostly applied to terrains that are well-studied, well-explored, and for which high-quality data is readily available. However, despite lacking protracted exploration histories and high-quality data, many frontier regions may have high-potential for hosting world-class mineral deposits and may benefit from mineral potential mapping exercises. Sovereign risk factors can limit the scope of previous work in a frontier region, and previous research in such areas is often limited and/or inaccessible, publicly available literature and data can be restricted, and any available data may also be unreliable. Mineral potential mapping using GIS in a frontier region presents many challenges in terms of the data availability (eg. non-existent information, lack of digital data) and data quality (eg. inaccuracy, incomplete coverage). The quality of the final mineral potential map is limited by the quality of the input data and as such, is affected by data availability and quality. Such issues are not limited to frontier regions, but they are often compounded by having multiple weaknesses within the same dataset, which is uncommon for data in more well-explored, data-rich areas. We show how mineral potential mapping can be successfully applied to frontier regions in order to delineate targets with high potential for hosting a mineral deposit despite the data challenges posed. Data is evaluated using the weights of evidence and fuzzy logic methods due to their effectiveness in dealing with incomplete geoscientific datasets. Weights of evidence may be employed as a data driven method for indirectly evaluating the

Mineral resource of the month: molybdenum

USGS Publications Warehouse

Polyak, Désire E.

2011-01-01

The article offers information about the mineral molybdenum. Sources includes byproduct or coproduct copper-molybdenum deposits in the Western Cordillera of North and South America. Among the uses of molybdenum are stainless steel applications, as an alloy material for manufacturing vessels and as lubricants, pigments or chemicals. Also noted is the role played by molybdenum in renewable energy technology.

Isolation and the interaction between a mineral-weathering Rhizobium tropici Q34 and silicate minerals.

PubMed

Wang, Rong Rong; Wang, Qi; He, Lin Yan; Qiu, Gang; Sheng, Xia Fang

2015-05-01

The purposes of this study were to isolate and evaluate the interaction between mineral-weathering bacteria and silicate minerals (feldspar and biotite). A mineral-weathering bacterium was isolated from weathered rocks and identified as Rhizobium tropici Q34 based on 16S rRNA gene sequence analysis. Si and K concentrations were increased by 1.3- to 4.0-fold and 1.1- to 1.7-fold in the live bacterium-inoculated cultures compared with the controls respectively. Significant increases in the productions of tartaric and succinic acids and extracellular polysaccharides by strain Q34 were observed in cultures with minerals. Furthermore, significantly more tartaric acid and polysaccharide productions by strain Q34 were obtained in the presence of feldspar, while better growth and more citric acid production of strain Q34 were observed in the presence of biotite. Mineral dissolution experiments showed that the organic acids and polysaccharides produced by strain Q34 were also capable of promoting the release of Si and K from the minerals. The results showed that the growth and metabolite production of strain Q34 were enhanced in the presence of the minerals and different mineral exerted distinct impacts on the growth and metabolite production. The bio-weathering process is probably a synergistic action of organic acids and extracellular polysaccharides produced by the bacterium.

Mineral content of complementary foods.

PubMed

Jani, Rati; Udipi, S A; Ghugre, P S

2009-01-01

To document mineral contents iron, zinc, calcium, energy contents and nutrient densities in complementary foods commonly given to young urban slum children. Information on dietary intake was collected from 892 mothers of children aged 13-24 months, using 24 hour dietary recall and standardized measures. Three variations of 27 most commonly prepared recipes were analyzed and their energy (Kcal/g) and nutrient densities (mg/100 Kcal) were calculated. Considerable variations were observed in preparation of all items fed to the children. Cereal-based items predominated their diets with only small amount of vegetables/fruits. Fenugreek was the only leafy vegetable included, but was given to only 1-2% of children. Iron, calcium, zinc contents of staple complementary foods ranged from: 0.33 mg to 3.73 mg, 4 mg to 64 mg, and 0.35 mg to 2.99 mg/100 respectively. Recipes diluted with less water and containing vegetables, spices had higher mineral content. Minerals densities were higher for dals, fenugreek vegetable, khichdi and chapatti. Using the median amounts of the various recipes fed to children, intakes of all nutrients examined especially calcium and iron was low. There is an urgent need to educate mothers about consistency, dilution, quantity, frequency, method of preparation, inclusion of micronutrient-rich foods, energy-dense complementary foods and gender equality.

30 CFR 48.6 - Experienced miner training.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING... utilized at the mine shall be observed and explained. (2) Mandatory health and safety standards. The course shall include the mandatory health and safety standards pertinent to the tasks to be assigned. (3...

30 CFR 48.6 - Experienced miner training.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR EDUCATION AND TRAINING... utilized at the mine shall be observed and explained. (2) Mandatory health and safety standards. The course shall include the mandatory health and safety standards pertinent to the tasks to be assigned. (3...

Re-evaluation of Non-regulatory Asbestos Group Minerals for Regulatory Agencies