Modeling end-of-life pathways of construction and demolition debris in the United States (poster for LCM 2017)

EPA Science Inventory

In 2013, the United States generated 530 million tons of construction and demolition debris (CDD), 90% of which was related to demolition. Despite this major contribution to national waste streams, Life Cycle Assessment (LCA) studies and product declarations of buildings and buil...

Estimating rooftop solar technical potential across the US using a combination of GIS-based methods, lidar data, and statistical modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gagnon, Pieter; Margolis, Robert; Melius, Jennifer

We provide a detailed estimate of the technical potential of rooftop solar photovoltaic (PV) electricity generation throughout the contiguous United States. This national estimate is based on an analysis of select US cities that combines light detection and ranging (lidar) data with a validated analytical method for determining rooftop PV suitability employing geographic information systems. We use statistical models to extend this analysis to estimate the quantity and characteristics of roofs in areas not covered by lidar data. Finally, we model PV generation for all rooftops to yield technical potential estimates. At the national level, 8.13 billion m 2 ofmore » suitable roof area could host 1118 GW of PV capacity, generating 1432 TWh of electricity per year. This would equate to 38.6% of the electricity that was sold in the contiguous United States in 2013. This estimate is substantially higher than a previous estimate made by the National Renewable Energy Laboratory. The difference can be attributed to increases in PV module power density, improved estimation of building suitability, higher estimates of total number of buildings, and improvements in PV performance simulation tools that previously tended to underestimate productivity. Also notable, the nationwide percentage of buildings suitable for at least some PV deployment is high—82% for buildings smaller than 5000 ft 2 and over 99% for buildings larger than that. In most states, rooftop PV could enable small, mostly residential buildings to offset the majority of average household electricity consumption. Even in some states with a relatively poor solar resource, such as those in the Northeast, the residential sector has the potential to offset around 100% of its total electricity consumption with rooftop PV.« less

Estimating rooftop solar technical potential across the US using a combination of GIS-based methods, lidar data, and statistical modeling

DOE PAGES

Gagnon, Pieter; Margolis, Robert; Melius, Jennifer; ...

2018-01-05

We provide a detailed estimate of the technical potential of rooftop solar photovoltaic (PV) electricity generation throughout the contiguous United States. This national estimate is based on an analysis of select US cities that combines light detection and ranging (lidar) data with a validated analytical method for determining rooftop PV suitability employing geographic information systems. We use statistical models to extend this analysis to estimate the quantity and characteristics of roofs in areas not covered by lidar data. Finally, we model PV generation for all rooftops to yield technical potential estimates. At the national level, 8.13 billion m 2 ofmore » suitable roof area could host 1118 GW of PV capacity, generating 1432 TWh of electricity per year. This would equate to 38.6% of the electricity that was sold in the contiguous United States in 2013. This estimate is substantially higher than a previous estimate made by the National Renewable Energy Laboratory. The difference can be attributed to increases in PV module power density, improved estimation of building suitability, higher estimates of total number of buildings, and improvements in PV performance simulation tools that previously tended to underestimate productivity. Also notable, the nationwide percentage of buildings suitable for at least some PV deployment is high—82% for buildings smaller than 5000 ft 2 and over 99% for buildings larger than that. In most states, rooftop PV could enable small, mostly residential buildings to offset the majority of average household electricity consumption. Even in some states with a relatively poor solar resource, such as those in the Northeast, the residential sector has the potential to offset around 100% of its total electricity consumption with rooftop PV.« less

Estimating rooftop solar technical potential across the US using a combination of GIS-based methods, lidar data, and statistical modeling

NASA Astrophysics Data System (ADS)

Gagnon, Pieter; Margolis, Robert; Melius, Jennifer; Phillips, Caleb; Elmore, Ryan

2018-02-01

We provide a detailed estimate of the technical potential of rooftop solar photovoltaic (PV) electricity generation throughout the contiguous United States. This national estimate is based on an analysis of select US cities that combines light detection and ranging (lidar) data with a validated analytical method for determining rooftop PV suitability employing geographic information systems. We use statistical models to extend this analysis to estimate the quantity and characteristics of roofs in areas not covered by lidar data. Finally, we model PV generation for all rooftops to yield technical potential estimates. At the national level, 8.13 billion m2 of suitable roof area could host 1118 GW of PV capacity, generating 1432 TWh of electricity per year. This would equate to 38.6% of the electricity that was sold in the contiguous United States in 2013. This estimate is substantially higher than a previous estimate made by the National Renewable Energy Laboratory. The difference can be attributed to increases in PV module power density, improved estimation of building suitability, higher estimates of total number of buildings, and improvements in PV performance simulation tools that previously tended to underestimate productivity. Also notable, the nationwide percentage of buildings suitable for at least some PV deployment is high—82% for buildings smaller than 5000 ft2 and over 99% for buildings larger than that. In most states, rooftop PV could enable small, mostly residential buildings to offset the majority of average household electricity consumption. Even in some states with a relatively poor solar resource, such as those in the Northeast, the residential sector has the potential to offset around 100% of its total electricity consumption with rooftop PV.

Educational Leadership and Racism: A Narrative Inquiry into Second-Generation Segregation

ERIC Educational Resources Information Center

Brooks, Jeffrey; Arnold, Noelle Witherspoon; Brooks, Melanie C.

2013-01-01

Background/Context: In-school racial segregation, also called second-generation segregation, is a social dynamic that is manifest in different and complicated ways in schoolhouses across the United States. This study sought to investigate how building-level leadership facilitates or impedes the practice of racial equity in an urban high school,…

76 FR 8607 - Airworthiness Directives; The Cessna Aircraft Company Model 750 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-15

... Administration (FAA), DOT. ACTION: Final rule. SUMMARY: We are adopting a new airworthiness directive (AD) for... auxiliary power unit (APU) generator and the left and right engine direct current (DC) generators, and... Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590. FOR FURTHER...

6. Photographic copy of a photograph taken from pasteup negatives ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. Photographic copy of a photograph taken from paste-up negatives for U.S. Army Corps of Engineers document GF-500-MCP, entitled "Grand Forks Site RLS Army Operating Drawings, Master Composite Photographs for SAFEGUARD TSE Systems and Equipment," Page 9, dated 1 September 1974 (original document and negatives in possession of U.S. Army Corps of Engineers, Huntsville, AL). Photographer unknown. View of remote launch operations building, power generation room #124, showing no-break units NB-1002 (A) and NB-1001 (B). This equipment consisted of a 150 horsepower, d.c. operational motor which drove, on each end of the extended shaft, a 70 kw generator and a 30 kw generator unit. It was designed to provide continuous power service for launch equipment. In particular, the photo is an excellent representation of the shock isolation scheme, as evidenced by the supporting air springs and equipment platform - Stanley R. Mickelsen Safeguard Complex, Remote Launch Operations Building, Near Service Road exit from Patrol Road, Nekoma, Cavalier County, ND

A diagnostic expert system for aircraft generator control unit (GCU)

NASA Astrophysics Data System (ADS)

Ho, Ting-Long; Bayles, Robert A.; Havlicsek, Bruce L.

The modular VSCF (variable-speed constant-frequency) generator families are described as using standard modules to reduce the maintenance cost and to improve the product's testability. A general diagnostic expert system shell that guides troubleshooting of modules or line replaceable units (LRUs) is introduced. An application of the diagnostic system to a particular LRU, the generator control unit (GCU) is reported. The approach to building the diagnostic expert system is first to capture general diagnostic strategy in an expert system shell. This shell can be easily applied to different devices or LRUs by writing rules to capture only additional device-specific diagnostic information from expert repair personnel. The diagnostic system has the necessary knowledge embedded in its programs and exhibits expertise to troubleshoot the GCU.

Engaging communities and climate change futures with Multi-Scale, Iterative Scenario Building (MISB) in the western United States

Treesearch

Daniel Murphy; Carina Wyborn; Laurie Yung; Daniel R. Williams; Cory Cleveland; Lisa Eby; Solomon Dobrowski; Erin Towler

2016-01-01

Current projections of future climate change foretell potentially transformative ecological changes that threaten communities globally. Using two case studies from the United States Intermountain West, this article highlights the ways in which a better articulation between theory and methods in research design can generate proactive applied tools that enable...

Survival of Listeria monocytogenes, E.coli 0157:H7 and Salmonella spp. on catfish fillets exposed to microwave heating in a continuous mode

USDA-ARS?s Scientific Manuscript database

Microwave (MW) heating using continuous power output with feedback control and a modified ingredient formulation, may provide better and consistent cooking of foods. Currently, household units with build-in inverter power supply units are available. These new generation microwave ovens provide con...

4. DETAIL OF SMOKE GENERATOR; NORTH SIDE OF LEVEL SIX, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. DETAIL OF SMOKE GENERATOR; NORTH SIDE OF LEVEL SIX, LOOKING WEST; HICKORY SAWDUST DROPPED FROM HOPPER ONTO HEATED PLATE TO MAKE SMOKE, WHICH WAS THEN DISTRIBUTED THROUGH SQUARE DUCTS (TOP CENTER) TO INDIVIDUAL SMOKEHOUSE UNITS - Rath Packing Company, Smokehouse-Hog Chilling Building, Sycamore Street between Elm & Eighteenth Streets, Waterloo, Black Hawk County, IA

Draco,Version 6.x.x

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, Kelly; Budge, Kent; Lowrie, Rob

2016-03-03

Draco is an object-oriented component library geared towards numerically intensive, radiation (particle) transport applications built for parallel computing hardware. It consists of semi-independent packages and a robust build system. The packages in Draco provide a set of components that can be used by multiple clients to build transport codes. The build system can also be extracted for use in clients. Software includes smart pointers, Design-by-Contract assertions, unit test framework, wrapped MPI functions, a file parser, unstructured mesh data structures, a random number generator, root finders and an angular quadrature component.

Automatic generation and simulation of urban building energy models based on city datasets for city-scale building retrofit analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Yixing; Hong, Tianzhen; Piette, Mary Ann

Buildings in cities consume 30–70% of total primary energy, and improving building energy efficiency is one of the key strategies towards sustainable urbanization. Urban building energy models (UBEM) can support city managers to evaluate and prioritize energy conservation measures (ECMs) for investment and the design of incentive and rebate programs. This paper presents the retrofit analysis feature of City Building Energy Saver (CityBES) to automatically generate and simulate UBEM using EnergyPlus based on cities’ building datasets and user-selected ECMs. CityBES is a new open web-based tool to support city-scale building energy efficiency strategic plans and programs. The technical details ofmore » using CityBES for UBEM generation and simulation are introduced, including the workflow, key assumptions, and major databases. Also presented is a case study that analyzes the potential retrofit energy use and energy cost savings of five individual ECMs and two measure packages for 940 office and retail buildings in six city districts in northeast San Francisco, United States. The results show that: (1) all five measures together can save 23–38% of site energy per building; (2) replacing lighting with light-emitting diode lamps and adding air economizers to existing heating, ventilation and air-conditioning (HVAC) systems are most cost-effective with an average payback of 2.0 and 4.3 years, respectively; and (3) it is not economical to upgrade HVAC systems or replace windows in San Francisco due to the city's mild climate and minimal cooling and heating loads. Furthermore, the CityBES retrofit analysis feature does not require users to have deep knowledge of building systems or technologies for the generation and simulation of building energy models, which helps overcome major technical barriers for city managers and their consultants to adopt UBEM.« less

Automatic generation and simulation of urban building energy models based on city datasets for city-scale building retrofit analysis

DOE PAGES

Chen, Yixing; Hong, Tianzhen; Piette, Mary Ann

2017-08-07

Buildings in cities consume 30–70% of total primary energy, and improving building energy efficiency is one of the key strategies towards sustainable urbanization. Urban building energy models (UBEM) can support city managers to evaluate and prioritize energy conservation measures (ECMs) for investment and the design of incentive and rebate programs. This paper presents the retrofit analysis feature of City Building Energy Saver (CityBES) to automatically generate and simulate UBEM using EnergyPlus based on cities’ building datasets and user-selected ECMs. CityBES is a new open web-based tool to support city-scale building energy efficiency strategic plans and programs. The technical details ofmore » using CityBES for UBEM generation and simulation are introduced, including the workflow, key assumptions, and major databases. Also presented is a case study that analyzes the potential retrofit energy use and energy cost savings of five individual ECMs and two measure packages for 940 office and retail buildings in six city districts in northeast San Francisco, United States. The results show that: (1) all five measures together can save 23–38% of site energy per building; (2) replacing lighting with light-emitting diode lamps and adding air economizers to existing heating, ventilation and air-conditioning (HVAC) systems are most cost-effective with an average payback of 2.0 and 4.3 years, respectively; and (3) it is not economical to upgrade HVAC systems or replace windows in San Francisco due to the city's mild climate and minimal cooling and heating loads. Furthermore, the CityBES retrofit analysis feature does not require users to have deep knowledge of building systems or technologies for the generation and simulation of building energy models, which helps overcome major technical barriers for city managers and their consultants to adopt UBEM.« less

Building Units Design and Scale Chemistry

NASA Astrophysics Data System (ADS)

Férey, Gérard

2000-06-01

The concept of a building unit (BU) is used in two ways: the first is an a posteriori tool for description of structures which can be used to imagine new topologies originating from the description; the second one, restricted to the routes leading to the solid from the solution, starts from the reality of these building units in the solution to design new solids obtained by the tuned precipitation of these BUs with proper counterions. The room temperature and the hydrothermal routes are examined. The existence of BUs with different sizes with close topologies, revealed by numerous examples, leads us to define the notion of "scale chemistry" which concerns the edification of solids with various BUs, either organic, hybrid, or inorganic, and the consequences it has for the corresponding frameworks and the voids they generate. Not only the framework is important, and applications of the existence of large cavities are discussed. The paper ends with a discussion of the new trends which arise from this topological concept.

Measuring and Understanding the Energy Use Signatures of a Bank Building

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, YuLong; Liu, Bing; Athalye, Rahul A.

The Pacific Northwest National Laboratory measured and analyzed the energy end-use patterns in a bank building located in the north-eastern United States. This work was performed in collaboration with PNC Financial Service Group under the US DOE’s Commercial Building Partnerships Program. This paper presents the metering study and the results of the metered data analysis. It provides a benchmark for the energy use of different bank-related equipments. The paper also reveals the importance of metering in fully understanding building loads and indentifying opportunities for energy efficiency improvements that will have impacts across PNC’s portfolio of buildings and were crucial tomore » reducing receptacle loads in the design of a net-zero bank branches. PNNL worked with PNC to meter a 4,000 ft2 bank branch in the state of Pennsylvania. 71 electrical circuits were monitored and 25 stand-alone watt-hour meters were installed at the bank. These meters monitored the consumption of all interior and exterior lighting, receptacle loads, service water heating, and the HVAC rooftop unit at a 5-minute sampling interval from November 2009 to November 2010. A total of over 8 million data records were generated, which were then analyzed to produce the end-use patterns, daily usage profiles, rooftop unit usage cycles, and inputs for calibrating the energy model of the building.« less

Woody residues and solid waste wood available for recovery in the United States, 2002

Treesearch

David B. McKeever; Robert H. Falk

2004-01-01

Large amounts of woody residues and solid wood waste are generated annually in the United States from the extraction of timber from forests, from forestry cultural operations, in the conversion of forest land to nonforest uses, in the initial processing of roundwood timber into usable products, in the construction and demolition of buildings and structures, and in the...

Industrial wastes from the boat-building sector in the Marche Region (Italy): a parametric and chemical-physical characterization.

PubMed

Carchesio, M; Tatàno, F; Tosi, G; Trivellone, C H

2013-01-01

Using the renowned leisure boat-building sector in the Marche Region (Italy) as a case-study, this paper addresses the characterization of (1) the industrial waste generation from the building of composite material-based boats and (2) some chemical-physical properties of representative types of boat-building residues (plastic foam, hardened resin, fibre-reinforced composite residues, and sanding dust). A parametric evaluation based on the number of employees gave a representative unit generation rate per employee (UGRpE) of 1.47 tons(waste) employee(-1) year(-1) for the entire Marche regional boatbuilding district, whereas evaluations carried out separately for three case-study companies provided values of 1.56, 3.07, and 1.12 tons(waste) employee(-1) year(-1) as representative for a mass-produced motor boat builder (case-study company '1'), a customized sailing boat builder (case-study company '2'), and a mould and structural component builder (case-study company '3'), respectively. The original proposal and evaluation of two additional generation rates based on physical characteristics intrinsic to the manufactured product, i.e. the unit generation rate per boat area (UGRpA) and per boat weight (UGRpW), confirmed the higher waste generation for the sailing boat builder(representative UGRpA and UGRpW values of 0.35 tons(waste) m(-2)(boat) year(-1) and 2. 71 tons(waste) tons(-1)(boat) year(-1), respectively) compared with the motor boat builder (representative UGRpA and UGRpW values of 0.06 tons(waste) m(-2)(boat) year(-1) and 0.49 tons(waste) tons(-1)(boat) year(-1), respectively). The chemical-physical property characterization of the selected residues revealed the following aspects: a general condition of low moisture contents; significant ash contents in the glass- and carbon-fibre composite residues and the correlated sanding dust; and relatively high energy content values in the overall range 14,144-32,479 kJ kg(-1), expressed as the lower heating value.

Aternating current photovoltaic building block

DOEpatents

Bower, Ward Issac; Thomas, Michael G.; Ruby, Douglas S.

2004-06-15

A modular apparatus for and method of alternating current photovoltaic power generation comprising via a photovoltaic module, generating power in the form of direct current; and converting direct current to alternating current and exporting power via one or more power conversion and transfer units attached to the module, each unit comprising a unitary housing extending a length or width of the module, which housing comprises: contact means for receiving direct current from the module; one or more direct current-to-alternating current inverters; an alternating current bus; and contact means for receiving alternating current from the one or more inverters.

Molecular docking sites designed for the generation of highly crystalline covalent organic frameworks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ascherl, Laura; Sick, Torben; Margraf, Johannes

Covalent organic frameworks (COFs) formed by connecting multidentate organic building blocks through covalent bonds provide a platform for designing multifunctional porous materials with atomic precision. As they are promising materials for applications in optoelectronics, they would benefit from a maximum degree of long-range order within the framework, which has remained a major challenge. We have developed a synthetic concept to allow consecutive COF sheets to lock in position during crystal growth, and thus minimize the occurrence of stacking faults and dislocations. Hereby, the three-dimensional conformation of propeller-shaped molecular building units was used to generate well-defined periodic docking sites, which guidedmore » the attachment of successive building blocks that, in turn, promoted long-range order during COF formation. This approach enables us to achieve a very high crystallinity for a series of COFs that comprise tri- and tetradentate central building blocks. We expect this strategy to be transferable to a broad range of customized COFs.« less

Molecular docking sites designed for the generation of highly crystalline covalent organic frameworks

NASA Astrophysics Data System (ADS)

Ascherl, Laura; Sick, Torben; Margraf, Johannes T.; Lapidus, Saul H.; Calik, Mona; Hettstedt, Christina; Karaghiosoff, Konstantin; Döblinger, Markus; Clark, Timothy; Chapman, Karena W.; Auras, Florian; Bein, Thomas

2016-04-01

Covalent organic frameworks (COFs) formed by connecting multidentate organic building blocks through covalent bonds provide a platform for designing multifunctional porous materials with atomic precision. As they are promising materials for applications in optoelectronics, they would benefit from a maximum degree of long-range order within the framework, which has remained a major challenge. We have developed a synthetic concept to allow consecutive COF sheets to lock in position during crystal growth, and thus minimize the occurrence of stacking faults and dislocations. Hereby, the three-dimensional conformation of propeller-shaped molecular building units was used to generate well-defined periodic docking sites, which guided the attachment of successive building blocks that, in turn, promoted long-range order during COF formation. This approach enables us to achieve a very high crystallinity for a series of COFs that comprise tri- and tetradentate central building blocks. We expect this strategy to be transferable to a broad range of customized COFs.

75 FR 18826 - Mr. Howard Rosenfeld; Notice of Preliminary Permit Application Accepted for Filing and Soliciting...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-13

... to; (4) an existing 25-foot-high, 22-foot-square stone-masonry building to house; (5) a new turbine generator unit, with a maximum hydraulic capacity of 5 cubic feet per second (cfs) and total installed...

Gas-turbine expander power generating systems for internal needs of compressor stations of gas-main pipelines

NASA Astrophysics Data System (ADS)

Shimanov, A. A.; Biryuk, V. V.; Sheludko, L. P.; Shabanov, K. Yu.

2017-08-01

In the framework of this paper, there have been analyzed power station building methods to construct a power station for utilities for gas-main pipelines compressor stations. The application efficiency of turbo expanders in them to expand the power gas of compressor stations' gas compressor units has been shown. New schemes for gas-turbine expander power generating systems have been proposed.

Low-level radwaste storage facility at Hope Creek and Salem Generating Stations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oyen, L.C.; Lee, K.; Bravo, R.

Following the January 1, 1993, closure of the radwaste disposal facilities at Beatty, Nevada, and Richland, Washington (to waste generators outside the compact), only Barnwell, South Carolina, is open to waste generators in most states. Barnwell is scheduled to stay open to waste generators outside the Southeast Compact until June 30, 1994. Continued delays in opening regional radwaste disposal facilities have forced most nuclear utilities to consider on-site storage of low-level radwaste. Public Service Electric and Gas Company (PSE G) considered several different radwaste storage options before selecting the design based on the steel-frame and metal-siding building design described inmore » the Electric Power Research Institute's (EPRI's) TR-100298 Vol. 2, Project 3800 report. The storage facility will accommodate waste generated by Salem units 1 and 2 and Hope Creek unit 1 for a 5-yr period and will be located within their common protected area.« less

Technology Solutions for New and Existing Homes Case Study: Addressing Multifamily Piping Losses with Solar Hot Water

DOE Office of Scientific and Technical Information (OSTI.GOV)

D. Springer, M. Seitzler, and C. Backman

2016-12-01

Sun Light & Power, a San Francisco Bay Area solar design-build contractor, teamed with the U.S. Department of Energy’s Building America partner the Alliance for Residential Building Innovation (ARBI) to study this heat-loss issue. The team added three-way valves to the solar water heating systems for two 40-unit multifamily buildings. In these systems, when the stored solar hot water is warmer than the recirculated hot water returning from the buildings, the valves divert the returning water to the solar storage tank instead of the water heater. This strategy allows solar-generated heat to be applied to recirculation heat loss in additionmore » to heating water that is consumed by fixtures and appliances.« less

Assessing high shares of renewable energies in district heating systems - a case study for the city of Herten

NASA Astrophysics Data System (ADS)

Aydemir, Ali; Popovski, Eftim; Bellstädt, Daniel; Fleiter, Tobias; Büchele, Richard

2017-11-01

Many earlier studies have assessed the DH generation mix without taking explicitly into account future changes in the building stock and heat demand. The approach of this study consists of three steps that combine stock modeling, energy demand forecasting, and simulation of different energy technologies. First, a detailed residential building stock model for Herten is constructed by using remote sensing together with a typology for the German building stock. Second, a bottom-up simulation model is used which calculates the thermal energy demand based on energy-related investments in buildings in order to forecast the thermal demand up to 2050. Third, solar thermal fields in combination with large-scale heat pumps are sized as an alternative to the current coal-fired CHPs. We finally assess cost of heat and CO2 reduction for these units for two scenarios which differ with regard to the DH expansion. It can be concluded that up to 2030 and 2050 a substantial reduction in buildings heat demand due to the improved building insulation is expected. The falling heat demand in the DH substantially reduces the economic feasibility of new RES generation capacity. This reduction might be compensated by continuously connecting apartment buildings to the DH network until 2050.

20. VIEW OF THE INCINERATOR. DURING ROUTINE BUILDING OPERATIONS IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. VIEW OF THE INCINERATOR. DURING ROUTINE BUILDING OPERATIONS IN DECEMBER 1988, A HEAT PLUME WAS GENERATED THAT WAS REGISTERED ON FILM BY A PASSING AIRCRAFT. OFFICIALS WITH THE UNITED STATES ENVIRONMENTAL PROTECTION AGENCY (USEPA) BELIEVED THAT ILLEGAL OPERATIONS WERE BEING CONDUCTED. THE USEPA USED THIS OPPORTUNITY TO CONVINCE AUTHORITIES TO ISSUE A WARRANT TO ENTER THE ROCKY FLATS PLANT AND INVESTIGATE THE ALLEGATION. (4/98) - Rocky Flats Plant, Plutonium Recovery & Fabrication Facility, North-central section of plant, Golden, Jefferson County, CO

Southern Pine Beetle

Treesearch

Robert C. Thatcher; Patrick J. Barry

1982-01-01

The southern pine beetle (Dendroctonus frontalis Zimmermann) is one of pine's most destructive insect enemies in the Southern United States, Mexico, and Central America. Because populations build rapidly to outbreak proportions and large numbers of trees are killed, this insect generates considerable concern among managers of southern pine forests. The beetle...

Greening the Bottom Line, 2012

ERIC Educational Resources Information Center

Flynn, Emily

2012-01-01

With buildings consuming almost half (49 percent) of all energy used in the United States, and three quarters of all electricity, there is a compelling need for investment in energy efficiency upgrades. These energy saving improvements "represent a significant opportunity to save money, reduce climate impact and generate jobs," according…

Environmental Stewardship through Service Learning

ERIC Educational Resources Information Center

Kaye, Cathryn Berger

2011-01-01

New school buildings often grab headlines that highlight their green features and LEED (Leadership in Energy and Environmental Design) certification, yet nearly 90% of schools in the United States were built before 1985, with the largest portion built from 1950-69 to accommodate the baby boom generation (National Clearinghouse for Educational…

Advanced Stirling Radioisotope Generator Engineering Unit 2 (ASRG EU2) Final Assembly

NASA Technical Reports Server (NTRS)

Oriti, Salvatore M.

2015-01-01

NASA Glenn Research Center (GRC) has recently completed the assembly of a unique Stirling generator test article for laboratory experimentation. Under the Advanced Stirling Radioisotope Generator (ASRG) flight development contract, NASA GRC initiated a task to design and fabricate a flight-like generator for in-house testing. This test article was given the name ASRG Engineering Unit 2 (EU2) as it was effectively the second engineering unit to be built within the ASRG project. The intent of the test article was to duplicate Lockheed Martin's qualification unit ASRG design as much as possible to enable system-level tests not previously possible at GRC. After the cancellation of the ASRG flight development project, the decision was made to continue the EU2 build, and make use of a portion of the hardware from the flight development project. GRC and Lockheed Martin engineers collaborated to develop assembly procedures, leveraging the valuable knowledge gathered by Lockheed Martin during the ASRG development contract. The ASRG EU2 was then assembled per these procedures at GRC with Lockheed Martin engineers on site. The assembly was completed in August 2014. This paper details the components that were used for the assembly, and the assembly process itself.

The National Military Strategy of the United States of America 2015: The United States Military’s Contribution to National Security

DTIC Science & Technology

2015-06-01

are amplified by shifting demographics. Youth populations are rapidly growing in Africa and the Middle East, regions that face resource shortages...fear in opponents and generate support for their causes. They use improvised explosive devices (IED), suicide vests, and tailored cyber tools to...our security relationship with India and build upon our partnerships with New Zealand, Singapore, Indonesia, Malaysia , Vietnam, and Bangladesh. Such

"Life without nuclear power": A nuclear plant retirement formulation model and guide based on economics. San Onofre Nuclear Generating Station case: Economic impacts and reliability considerations leading to plant retirement

NASA Astrophysics Data System (ADS)

Wasko, Frank

Traditionally, electric utilities have been slow to change and very bureaucratic in nature. This culture, in and of itself, has now contributed to a high percentage of United States electric utilities operating uneconomical nuclear plants (Crooks, 2014). The economic picture behind owning and operating United States nuclear plants is less than favorable for many reasons including rising fuel, capital and operating costs (EUCG, 2012). This doctoral dissertation is specifically focused on life without nuclear power. The purpose of this dissertation is to create a model and guide that will provide electric utilities who currently operate or will operate uneconomical nuclear plants the opportunity to economically assess whether or not their nuclear plant should be retired. This economic assessment and stakeholder analysis will provide local government, academia and communities the opportunity to understand how Southern California Edison (SCE) embraced system upgrade import and "voltage support" opportunities to replace "base load" generation from San Onofre Nuclear Generating Station (SONGS) versus building new replacement generation facilities. This model and guide will help eliminate the need to build large replacement generation units as demonstrated in the SONGS case analysis. The application of The Nuclear Power Retirement Model and Guide will provide electric utilities with economic assessment parameters and an evaluation assessment progression needed to better evaluate when an uneconomical nuclear plant should be retired. It will provide electric utilities the opportunity to utilize sound policy, planning and development skill sets when making this difficult decision. There are currently 62 nuclear power plants (with 100 nuclear reactors) operating in the United States (EIA, 2014). From this group, 38 are at risk of early retirement based on the work of Cooper (2013). As demonstrated in my model, 35 of the 38 nuclear power plants qualify to move to the economic assessment review and then on to the stakeholder cost benefit analysis (if model qualifications are met) leading to a final plant retirement decision. This application via the model and guide, in turn, will lead electric utilities to explore system upgrade import opportunities and mitigation measures versus building new replacement generation facilities. United States nuclear reactors are licensed for 40 years with a 20 year extension available prior to the expiration date (EIA, 2013). Since late 2012, electric power companies have announced the early retirement of four uneconomical nuclear power plants while other studies have indicated that as many as 70 percent of United States nuclear power plants are potentially at risk for early retirement (Crooks, 2014 and Cooper, 2013). A high percentage of these aforementioned nuclear plants have operating licenses that will not expire until 2030 and beyond. Thus, for the most part, replacement power contingency planning has not been initiated for these plants or is still in preliminary stages. The recent nuclear plant retirements are the first since 1998 (EIA, 2013). Decisions to retire the plants involved concerns over maintenance and repair costs as well as declining profitability (EIA, 2013). In addition, the Energy Information Administration (2010-2012) released data that demonstrated that the worst 25 percent of United States nuclear plants are far more expensive to operate and generate electricity than new gas plants. It is equally important to understand and explain the economic and power replacement implications to both ratepayers and end-users. A SONGS case study analysis will review the economic, operational and political challenges that SCE faced leading to the retirement decision of SONGS. As preface to the case study, replacement steam generators (RSGs) were installed in Unit 2 in 2009 and in Unit 3 in 2010. In January 2012, while Unit 2 was down for routine maintenance, a small leak was discovered inside a steam generator in Unit 3. Because of the situation, both units remained shut down to evaluate the cause of the leakage and to make repairs. SCE submitted plans to the Nuclear Regulatory Commission (NRC) to re-start Unit 2 at reduced power. However, concerns over the length of the review process and the high costs associated with steam generator repairs led SCE to retire both reactors (SCE SONGS Fact Sheets, 2012-2013). Finally, collaborative resource power replacement planning is needed more than ever as nuclear facilities in the United States are now being retired for economic related reasons (Crooks, 2014). This collaborative power replacement process and implementation must encompass all relevant stakeholders including state grid operators, ratepayers, shareholders and the electric utility company.

The second phase in creating the cardiac center for the next generation: beyond structure to process improvement.

PubMed

Woods, J

2001-01-01

The third generation cardiac institute will build on the successes of the past in structuring the service line, re-organizing to assimilate specialist interests, and re-positioning to expand cardiac services into cardiovascular services. To meet the challenges of an increasingly competitive marketplace and complex delivery system, the focus for this new model will shift away from improved structures, and toward improved processes. This shift will require a sound methodology for statistically measuring and sustaining process changes related to the optimization of cardiovascular care. In recent years, GE Medical Systems has successfully applied Six Sigma methodologies to enable cardiac centers to control key clinical and market development processes through its DMADV, DMAIC and Change Acceleration processes. Data indicates Six Sigma is having a positive impact within organizations across the United States, and when appropriately implemented, this approach can serve as a solid foundation for building the next generation cardiac institute.

Geospatial Modelling Approach for 3d Urban Densification Developments

NASA Astrophysics Data System (ADS)

Koziatek, O.; Dragićević, S.; Li, S.

2016-06-01

With growing populations, economic pressures, and the need for sustainable practices, many urban regions are rapidly densifying developments in the vertical built dimension with mid- and high-rise buildings. The location of these buildings can be projected based on key factors that are attractive to urban planners, developers, and potential buyers. Current research in this area includes various modelling approaches, such as cellular automata and agent-based modelling, but the results are mostly linked to raster grids as the smallest spatial units that operate in two spatial dimensions. Therefore, the objective of this research is to develop a geospatial model that operates on irregular spatial tessellations to model mid- and high-rise buildings in three spatial dimensions (3D). The proposed model is based on the integration of GIS, fuzzy multi-criteria evaluation (MCE), and 3D GIS-based procedural modelling. Part of the City of Surrey, within the Metro Vancouver Region, Canada, has been used to present the simulations of the generated 3D building objects. The proposed 3D modelling approach was developed using ESRI's CityEngine software and the Computer Generated Architecture (CGA) language.

Genetic and Functional Heterogeneity of Tumors in Neurofibromatosis 2

DTIC Science & Technology

2016-07-01

mapped to the human genome build 37 (hg19) through BWA v. 0.5.9 [1] with parameters -q 5 -l 32 -k 2 –o 1. The resulting alignments were further sorted...see Table 2). Table 2 – Isogenic human arachnoidal cell (AC) clones with NF2 (exon 8) inactivating mutations generated by CRISPR/Cas genome editing...libraries were aligned to the human genome (GrCH37, Ensembl build 71) using Gsnap [19] version 2014_12_19. Expression levels of genes in the units of count

Building America Best Practices Series, Volume 6: High-Performance Home Technologies: Solar Thermal & Photovoltaic Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baechler, Michael C.; Gilbride, Theresa L.; Ruiz, Kathleen A.

This guide is was written by PNNL for the US Department of Energy's Building America program to provide information for residential production builders interested in building near zero energy homes. The guide provides indepth descriptions of various roof-top photovoltaic power generating systems for homes. The guide also provides extensive information on various designs of solar thermal water heating systems for homes. The guide also provides construction company owners and managers with an understanding of how solar technologies can be added to their homes in a way that is cost effective, practical, and marketable. Twelve case studies provide examples of productionmore » builders across the United States who are building energy-efficient homes with photovoltaic or solar water heating systems.« less

Second-generation supramolecular dendrimer with a defined structure due to orthogonal binding.

PubMed

Eckelmann, Jens; Dethlefs, Christiane; Brammer, Stefan; Doğan, Ahmet; Uphoff, Andreas; Lüning, Ulrich

2012-07-02

A second-generation supramolecular dendrimer has been prepared by orthogonal multiple hydrogen bonding. In the first (inner) recognition domain, the interaction of one bis-isocyanuric acid (25) with two branching units (21) that carry complementary Hamilton receptors has been exploited. In the second (outer) generation, the two ADDA (A=hydrogen-bond acceptor, D=donor) receptors of each branching unit (21) have bound complementary DAAD units (4). The problem of limited solubility of the building blocks has been overcome by the introduction of branched ethylhexyl residues and by the use of flexible alkylene or oligo(ethylene glycol) linking chains. The orthogonal binding of the two hydrogen-bonding pairs was elucidated by chemical induced shift NMR titrations, which proved that the two pairs, isocyanuric acid with the Hamilton receptor and ADDA with DAAD, bind preferentially. The formation of the supramolecular self-assembled 1:2:4 dendrimer with a molecular weight of 5065 g mol(-1) was investigated by diffusion NMR spectroscopy. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

New Model for Recruitment of Foreign Students Sparks Debate

ERIC Educational Resources Information Center

Moser, Kate

2008-01-01

A London-based company with an unusual model for helping colleges recruit international students has generated concern among faculty members as it has begun expanding into the United States. Into University Partnerships has formed joint ventures with five British universities, building centers where foreign students who may not have qualified for…

78 FR 45990 - Vogtle Electric Generating Station, Units 3 and 4; Southern Nuclear Operating Company; Change to...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-30

...The U.S. Nuclear Regulatory Commission (NRC) is granting both an exemption to allow a departure from the certification information of Tier 1 of the generic design control document (DCD) and is issuing License Amendment No. 8 to Combined Licenses (COL), NPF-91 and NPF-92. The COLs were issued to Southern Nuclear Operating Company, Inc., and Georgia Power Company, Oglethorpe Power Corporation, Municipal Electric Authority of Georgia, and the City of Dalton, Georgia (the licensee); for construction and operation of the Vogtle Electric Generating Plant (VEGP), Units 3 and 4, located in Burke County, Georgia. The amendment requests to revise the design of the bracing used to support the Turbine Building structure. This request requires changing Tier 1 information found in the Design Description portion of Updated Final Safety Analysis Report (UFSAR) Section 3.3, ``Buildings.'' The granting of the exemption allows the changes to Tier 1 information asked for in the amendment. Because the acceptability of the exemption was determined in part by the acceptability of the amendment, the exemption and amendment are being issued concurrently.

Hydropower Vision: Full Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

Hydropower has provided clean, affordable, reliable, and renewable electricity in the United States for more than a century. Building on hydropower’s historical significance, and to inform the continued technical evolution, energy market value, and environmental performance of the industry, the U.S. Department of Energy’s (DOE’s) Wind and Water Power Technologies Office has led a first-of-its-kind comprehensive analysis focused on a set of potential pathways for the environmentally sustainable expansion of hydropower (hydropower generation and pumped storage) in the United States.

United Space Alliance LLC Parachute Refurbishment Facility Model

NASA Technical Reports Server (NTRS)

Esser, Valerie; Pessaro, Martha; Young, Angela

2007-01-01

The Parachute Refurbishment Facility Model was created to reflect the flow of hardware through the facility using anticipated start and delivery times from a project level IV schedule. Distributions for task times were built using historical build data for SFOC work and new data generated for CLV/ARES task times. The model currently processes 633 line items from 14 SFOC builds for flight readiness, 16 SFOC builds returning from flight for defoul, wash, and dry operations, 12 builds for CLV manufacturing operations, and 1 ARES 1X build. Modeling the planned workflow through the PRF is providing a reliable way to predict the capability of the facility as well as the manpower resource need. Creating a real world process allows for real world problems to be identified and potential workarounds to be implemented in a safe, simulated world before taking it to the next step, implementation in the real world.

Twin-Mirrored-Galvanometer Laser-Light-Sheet Generator

NASA Technical Reports Server (NTRS)

Rhodes, David B.; Franke, John M.; Jones, Stephen B.; Leighty, Bradley D.

1991-01-01

Multiple, rotating laser-light sheets generated to illuminate flows in wind tunnels. Designed and developed to provide flexibility and adaptability to wide range of applications. Design includes capability to control size and location of laser-light sheet in real time, to generate horizontal or vertical sheets, to sweep sheet repeatedly through volume, to generate multiple sheets with controllable separation, and to rotate single or multiple laser-light sheets. Includes electronic equipment and laser mounted on adjustable-height platform. Twin-mirrored galvanometer unit supported by tripod to reduce vibration. Other possible applications include use in construction industry to align beams of building. Artistic or display applications also possible.

Heat pump system

DOEpatents

Swenson, Paul F.; Moore, Paul B.

1983-01-01

An air heating and cooling system for a building includes an expansion type refrigeration circuit and a vapor power circuit. The refrigeration circuit includes two heat exchangers, one of which is communicated with a source of indoor air from the building and the other of which is communicated with a source of air from outside the building. The vapor power circuit includes two heat exchangers, one of which is disposed in series air flow relationship with the indoor refrigeration circuit heat exchanger and the other of which is disposed in series air flow relationship with the outdoor refrigeration circuit heat exchanger. Fans powered by electricity generated by a vapor power circuit alternator circulate indoor air through the two indoor heat exchangers and circulate outside air through the two outdoor heat exchangers. The system is assembled as a single roof top unit, with a vapor power generator and turbine and compressor thermally insulated from the heat exchangers, and with the indoor heat exchangers thermally insulated from the outdoor heat exchangers.

Heat pump system

DOEpatents

Swenson, Paul F.; Moore, Paul B.

1977-01-01

An air heating and cooling system for a building includes an expansion type refrigeration circuit and a vapor power circuit. The refrigeration circuit includes two heat exchangers, one of which is communicated with a source of indoor air from the building and the other of which is communicated with a source of air from outside the building. The vapor power circuit includes two heat exchangers, one of which is disposed in series air flow relationship with the indoor refrigeration circuit heat exchanger and the other of which is disposed in series air flow relationship with the outdoor refrigeration circuit heat exchanger. Fans powered by electricity generated by a vapor power circuit alternator circulate indoor air through the two indoor heat exchangers and circulate outside air through the two outdoor heat exchangers. The system is assembled as a single roof top unit, with a vapor power generator and turbine and compressor thermally insulated from the heat exchangers, and with the indoor heat exchangers thermally insulated from the outdoor heat exchangers.

Heat pump system

DOEpatents

Swenson, Paul F.; Moore, Paul B.

1983-06-21

An air heating and cooling system for a building includes an expansion type refrigeration circuit and a vapor power circuit. The refrigeration circuit includes two heat exchangers, one of which is communicated with a source of indoor air from the building and the other of which is communicated with a source of air from outside the building. The vapor power circuit includes two heat exchangers, one of which is disposed in series air flow relationship with the indoor refrigeration circuit heat exchanger and the other of which is disposed in series air flow relationship with the outdoor refrigeration circuit heat exchanger. Fans powered by electricity generated by a vapor power circuit alternator circulate indoor air through the two indoor heat exchangers and circulate outside air through the two outdoor heat exchangers. The system is assembled as a single roof top unit, with a vapor power generator and turbine and compressor thermally insulated from the heat exchangers, and with the indoor heat exchangers thermally insulated from the outdoor heat exchangers.

75 FR 38845 - Exelon Generation Company, LLC; Three Mile Island Nuclear Station, Unit No. 1; Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-06

... ignition sources, hot work activities (activities such as welding or grinding), in situ and transient... is \\1/4\\- inch outside diameter tubing used for testing reactor building pressure switches. This... testing on the MU-V-20 backup air supply demonstrated that MU-V- 20 would only stay open for approximately...

Stimulating Excellence: Unleashing the Power of Innovation in Education

ERIC Educational Resources Information Center

Hess, Frederick M.

2009-01-01

The United States is facing one of the worst financial crises of recent history. America is also experiencing a quiet crisis, as well--one that has been building in the nation's classrooms and schools for decades. This nation is failing to prepare the next generation of Americans as citizens, thinkers, and graduates prepared for success in a…

Impact of warmer weather on electricity sector emissions due to building energy use

NASA Astrophysics Data System (ADS)

Meier, Paul; Holloway, Tracey; Patz, Jonathan; Harkey, Monica; Ahl, Doug; Abel, David; Schuetter, Scott; Hackel, Scott

2017-06-01

Most US energy consumption occurs in buildings, with cooling demands anticipated to increase net building electricity use under warmer conditions. The electricity generation units that respond to this demand are major contributors to sulfur dioxide (SO2) and nitrogen oxides (NOx), both of which have direct impacts on public health, and contribute to the formation of secondary pollutants including ozone and fine particulate matter. This study quantifies temperature-driven changes in power plant emissions due to increased use of building air conditioning. We compare an ambient temperature baseline for the Eastern US to a model-calculated mid-century scenario with summer-average temperature increases ranging from 1 C to 5 C across the domain. We find a 7% increase in summer electricity demand and a 32% increase in non-coincident peak demand. Power sector modeling, assuming only limited changes to current generation resources, calculated a 16% increase in emissions of NOx and an 18% increase in emissions of SO2. There is a high level of regional variance in the response of building energy use to climate, and the response of emissions to associated demand. The East North Central census region exhibited the greatest sensitivity of energy demand and associated emissions to climate.

Improving Building Energy Simulation Programs Through Diagnostic Testing (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2012-02-01

New test procedure evaluates quality and accuracy of energy analysis tools for the residential building retrofit market. Reducing the energy use of existing homes in the United States offers significant energy-saving opportunities, which can be identified through building simulation software tools that calculate optimal packages of efficiency measures. To improve the accuracy of energy analysis for residential buildings, the National Renewable Energy Laboratory's (NREL) Buildings Research team developed the Building Energy Simulation Test for Existing Homes (BESTEST-EX), a method for diagnosing and correcting errors in building energy audit software and calibration procedures. BESTEST-EX consists of building physics and utility billmore » calibration test cases, which software developers can use to compare their tools simulation findings to reference results generated with state-of-the-art simulation tools. Overall, the BESTEST-EX methodology: (1) Tests software predictions of retrofit energy savings in existing homes; (2) Ensures building physics calculations and utility bill calibration procedures perform to a minimum standard; and (3) Quantifies impacts of uncertainties in input audit data and occupant behavior. BESTEST-EX is helping software developers identify and correct bugs in their software, as well as develop and test utility bill calibration procedures.« less

At Issue: Marriage. Exploring the Debate over Marriage Rights for Same-Sex Couples: A Curriculum Guide for High School Educators.

ERIC Educational Resources Information Center

Gay, Lesbian, and Straight Education Network, New York, NY.

The Gay, Lesbian, and Straight Education Network (GLSEN) aims to unite with educators in cultivating an informed citizenry and future generations of children who respect and accept all people, regardless of their sexual orientation or gender identity. By supporting educators in their efforts to build schools where information and expression flow…

Teaching about Complex Systems Is No Simple Matter: Building Effective Professional Development for Computer-Supported Complex Systems Instruction

ERIC Educational Resources Information Center

Yoon, Susan A.; Anderson, Emma; Koehler-Yom, Jessica; Evans, Chad; Park, Miyoung; Sheldon, Josh; Schoenfeld, Ilana; Wendel, Daniel; Scheintaub, Hal; Klopfer, Eric

2017-01-01

The recent next generation science standards in the United States have emphasized learning about complex systems as a core feature of science learning. Over the past 15 years, a number of educational tools and theories have been investigated to help students learn about complex systems; but surprisingly, little research has been devoted to…

Guided-waves technique for inspecting the health of wall-covered building risers

NASA Astrophysics Data System (ADS)

Tse, Peter W.; Chen, J. M.; Wan, X.

2015-03-01

The inspection technique uses guided ultrasonic waves (GW) has been proven effective in detecting pipes' defects. However, as of today, the technique has not attracted much market attention because of insufficient field tests and lack of traceable records with proven results in commercial applications. In this paper, it presents the results obtained by using GW to inspect the defects occurred in real gas risers that are commonly installed in tall buildings. The purpose of having risers is to deliver gas from any building external piping system to each household unit of the building. The risers extend from the external wall of the building, penetrate thorough the concrete wall, into the kitchen or bathroom of each household unit. Similar to in-service pipes, risers are prone to corrosion due to water leaks into the concrete wall. However, the corrosion occurs in the section of riser, which is covered by the concrete wall, is difficult to be inspected by conventional techniques. Hence, GW technique was employed. The effectiveness of GW technique was tested by laboratory and on-site experiments using real risers gathered from tall buildings. The experimental results show that GW can partially penetrate thorough the riser's section that is covered by wall. The integrity of the wall-covered section of a riser can be determined by the reflected wave signals generated by the corroded area that may exit inside the wall-covered section. Based on the reflected wave signal, one can determine the health of the wall-covered riser.

Statistical Analysis of Solar PV Power Frequency Spectrum for Optimal Employment of Building Loads

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olama, Mohammed M; Sharma, Isha; Kuruganti, Teja

In this paper, a statistical analysis of the frequency spectrum of solar photovoltaic (PV) power output is conducted. This analysis quantifies the frequency content that can be used for purposes such as developing optimal employment of building loads and distributed energy resources. One year of solar PV power output data was collected and analyzed using one-second resolution to find ideal bounds and levels for the different frequency components. The annual, seasonal, and monthly statistics of the PV frequency content are computed and illustrated in boxplot format. To examine the compatibility of building loads for PV consumption, a spectral analysis ofmore » building loads such as Heating, Ventilation and Air-Conditioning (HVAC) units and water heaters was performed. This defined the bandwidth over which these devices can operate. Results show that nearly all of the PV output (about 98%) is contained within frequencies lower than 1 mHz (equivalent to ~15 min), which is compatible for consumption with local building loads such as HVAC units and water heaters. Medium frequencies in the range of ~15 min to ~1 min are likely to be suitable for consumption by fan equipment of variable air volume HVAC systems that have time constants in the range of few seconds to few minutes. This study indicates that most of the PV generation can be consumed by building loads with the help of proper control strategies, thereby reducing impact on the grid and the size of storage systems.« less

A Proof of Concept: Grizzly, the LWRS Program Materials Aging and Degradation Pathway Main Simulation Tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ben Spencer; Jeremey Busby; Richard Martineau

2012-10-01

Nuclear power currently provides a significant fraction of the United States’ non-carbon emitting power generation. In future years, nuclear power must continue to generate a significant portion of the nation’s electricity to meet the growing electricity demand, clean energy goals, and ensure energy independence. New reactors will be an essential part of the expansion of nuclear power. However, given limits on new builds imposed by economics and industrial capacity, the extended service of the existing fleet will also be required.

Evaluating the CO 2 emissions reduction potential and cost of power sector re-dispatch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steinberg, Daniel C.; Bielen, David A.; Townsend, Aaron

Prior studies of the U.S. electricity sector have recognized the potential to reduce carbon dioxide (CO2) emissions by substituting generation from coal-fired units with generation from under-utilized and lower-emitting natural gas-fired units; in fact, this type of 're-dispatch' was invoked as one of the three building blocks used to set the emissions targets under the Environmental Protection Agency's Clean Power Plan. Despite the existence of surplus natural gas capacity in the U.S., power system operational constraints not often considered in power sector policy analyses, such as transmission congestion, generator ramping constraints, minimum generation constraints, planned and unplanned generator outages, andmore » ancillary service requirements, could limit the potential and increase the cost of coal-to-gas re-dispatch. Using a highly detailed power system unit commitment and dispatch model, we estimate the maximum potential for re-dispatch in the Eastern Interconnection, which accounts for the majority of coal capacity and generation in the U.S. Under our reference assumptions, we find that maximizing coal-to-gas re-dispatch yields emissions reductions of 230 million metric tons (Mt), or 13% of power sector emissions in the Eastern Interconnection, with a corresponding average abatement cost of $15-$44 per metric ton of CO2, depending on the assumed supply elasticity of natural gas.« less

Responses of a tall building in Los Angeles, California as inferred from local and distant earthquakes

USGS Publications Warehouse

Çelebi, Mehmet; Hasan Ulusoy,; Nori Nakata,

2016-01-01

Increasing inventory of tall buildings in the United States and elsewhere may be subjected to motions generated by near and far seismic sources that cause long-period effects. Multiple sets of records that exhibited such effects were retrieved from tall buildings in Tokyo and Osaka ~ 350 km and 770 km from the epicenter of the 2011 Tohoku earthquake. In California, very few tall buildings have been instrumented. An instrumented 52-story building in downtown Los Angeles recorded seven local and distant earthquakes. Spectral and system identification methods exhibit significant low frequencies of interest (~0.17 Hz, 0.56 Hz and 1.05 Hz). These frequencies compare well with those computed by transfer functions; however, small variations are observed between the significant low frequencies for each of the seven earthquakes. The torsional and translational frequencies are very close and are coupled. Beating effect is observed in at least two of the seven earthquake data.

Solar energy potential of the largest buildings in the United States

NASA Astrophysics Data System (ADS)

Wence, E. R.; Grodsky, S.; Hernandez, R. R.

2017-12-01

Sustainable pathways of land use for energy are necessary to mitigate climate change and limit conversion of finite land resources needed for conservation and food production. Large, commercial buildings (LCBs) are increasing in size and number throughout the United States (US) and may serve as suitable recipient environments for photovoltaic (PV) solar energy infrastructure that may support a low carbon, low land footprint energy transition. In this study, we identified, characterized, and evaluated the technical potential of the largest, commercial building rooftops (i.e., exceeding 110,000 m2) and their associated parking lots in the US for PV solar energy systems using Aurora, a cloud-based solar optimization platform. We also performed a case study of building-specific electricity generation: electricity consumption balance. Further, we quantified the environmental co-benefit of land sparing and associated avoided emissions (t-CO2-eq) conferred under the counterfactual scenario that solar development would otherwise proceed as a ground-mounted, utility-scale PV installation of equal nominal capacity. We identified and mapped 37 LCBs (by rooftop area) across 18 states in the US, spanning from as far north as the state of Minnesota to as far south as Florida. Rooftop footprints range from 427,297 to 113,689 m2 and have a cumulative surface area of 99.8 million ft2. We characterize the LCBs as either: distribution/warehouse, factory, shopping center, or administrative office/facility. Three of the 37 LCBs currently support rooftop PV and the numbers of associated, detached buildings number up to 38. This study elucidates the extent to which LCBs and their respective parking lots can serve as suitable sites for PV solar energy generation. Lastly, this study demonstrates research-based applications of the Aurora energy modeling platform and informs decision-making focused on redirecting energy development towards human-modified landscapes to prioritize land use for biodiversity and agriculture.

26 CFR 1.42-15 - Available unit rule.

Code of Federal Regulations, 2010 CFR

2010-04-01

... maintain five of the residential units as low-income units, the qualified basis in the building is reduced... low-income building that is comparably sized or smaller than an over-income unit or, for deep rent.... Current resident means a person who is living in the low-income building. Low-income unit is defined by...

Concentrated solar power in the built environment

NASA Astrophysics Data System (ADS)

Montenon, Alaric C.; Fylaktos, Nestor; Montagnino, Fabio; Paredes, Filippo; Papanicolas, Costas N.

2017-06-01

Solar concentration systems are usually deployed in large open spaces for electricity generation; they are rarely used to address the pressing energy needs of the built environment sector. Fresnel technology offers interesting and challenging CSP energy pathways suitable for the built environment, due to its relatively light weight (<30 kg.m-2) and low windage. The Cyprus Institute (CyI) and Consorzio ARCA are cooperating in such a research program; we report here the construction and integration of a 71kW Fresnel CSP system into the HVAC (Heating, Ventilation, and Air Conditioning) system of a recently constructed office & laboratory building, the Novel Technologies Laboratory (NTL). The multi-generative system will support cooling, heating and hot water production feeding the system of the NTL building, as a demonstration project, part of the STS-MED program (Small Scale Thermal Solar District Units for Mediterranean Communities) financed by the European Commission under the European Neighbourhood and Partnership Instrument (ENPI), CBCMED program.

Comparative Study of DC and AC Microgrids in Commercial Buildings Across Different Climates and Operating Profiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fregosi, Daniel; Ravula, Sharmila; Brhlik, Dusan

2015-06-07

Bosch has developed and demonstrated a novel direct current (DC) microgrid system that maximizes the efficiency of locally generated photovoltaic energy while offering high reliability, safety, redundancy, and reduced cost compared to equivalent alternating current (AC) systems. Several demonstration projects validating the system feasibility and expected efficiency gains have been completed and additional ones are in progress. This paper gives an overview of the Bosch DC microgrid system and presents key results from a large simulation study done to estimate the energy savings of the Bosch DC microgrid over conventional AC systems. The study examined the system performance in locationsmore » across the United States for several commercial building types and operating profiles. It found that the Bosch DC microgrid uses generated PV energy 6%-8% more efficiently than traditional AC systems.« less

The 25 kW power module evolution study. Part 3: Conceptual designs for power module evolutions. Volume 3: Cost estimates

NASA Technical Reports Server (NTRS)

1979-01-01

Cost data generated for the evolutionary power module concepts selected are reported. The initial acquisition costs (design, development, and protoflight unit test costs) were defined and modeled for the baseline 25 kW power module configurations. By building a parametric model of this initial building block, the cost of the 50 kW and the 100 kW power modules were derived by defining only their configuration and programmatic differences from the 25 kW baseline module. Variations in cost for the quantities needed to fulfill the mission scenarios were derived by applying appropriate learning curves.

Negotiating Separateness and Accommodation: An Informed Reconsideration of Multiculturalism

DTIC Science & Technology

2012-03-22

grown al Qaeda-affiliated terrorists, spiked alarm in the United Kingdom.5 A less catastrophic, but equally worrisome concern relates to the...new means for the Amish to build consensus, select representatives, and confront authority in a unitary fashion. Equally noteworthy, it was the...significant problem for large Amish families who do not have enough land to sub-divide to support subsequent, and equally large, generations

How does a Next Generation Science Standard Aligned, Inquiry Based, Science Unit Impact Student Achievement of Science Practices and Student Science Efficacy in an Elementary Classroom?

NASA Astrophysics Data System (ADS)

Whittington, Kayla Lee

This study examined the impact of an inquiry based Next Generation Science Standard aligned science unit on elementary students' understanding and application of the eight Science and Engineering Practices and their relation in building student problem solving skills. The study involved 44 second grade students and three participating classroom teachers. The treatment consisted of a school district developed Second Grade Earth Science unit: What is happening to our playground? that was taught at the beginning of the school year. Quantitative results from a Likert type scale pre and post survey and from student content knowledge assessments showed growth in student belief of their own abilities in the science classroom. Qualitative data gathered from student observations and interviews performed at the conclusion of the Earth Science unit further show gains in student understanding and attitudes. This study adds to the existing literature on the importance of standard aligned, inquiry based science curriculum that provides time for students to engage in science practices.

Building intelligence in third-generation training and battle simulations

NASA Astrophysics Data System (ADS)

Jacobi, Dennis; Anderson, Don; von Borries, Vance; Elmaghraby, Adel; Kantardzic, Mehmed; Ragade, Rammohan

2003-09-01

Current war games and simulations are primarily attrition based, and are centered on the concept of force on force. They constitute what can be defined as "second generation" war games. So-called "first generation" war games were focused on strategy with the primary concept of mind on mind. We envision "third generation" war games and battle simulations as concentrating on effects with the primary concept being system on system. Thus the third generation systems will incorporate each successive generation and take into account strategy, attrition and effects. This paper will describe the principal advantages and features that need to be implemented to create a true "third generation" battle simulation and the architectural issues faced when designing and building such a system. Areas of primary concern are doctrine, command and control, allied and coalition warfare, and cascading effects. Effectively addressing the interactive effects of these issues is of critical importance. In order to provide an adaptable and modular system that will accept future modifications and additions with relative ease, we are researching the use of a distributed Multi-Agent System (MAS) that incorporates various artificial intelligence methods. The agent architecture can mirror the military command structure from both vertical and horizontal perspectives while providing the ability to make modifications to doctrine, command structures, inter-command communications, as well as model the results of various effects upon one another, and upon the components of the simulation. This is commonly referred to as "cascading effects," in which A affects B, B affects C and so on. Agents can be used to simulate units or parts of units that interact to form the whole. Even individuals can eventually be simulated to take into account the affect to key individuals such as commanders, heroes, and aces. Each agent will have a learning component built in to provide "individual intelligence" based on experience.

Pulsed thermionic converter study

NASA Technical Reports Server (NTRS)

1976-01-01

A nuclear electric propulsion concept using a thermionic reactor inductively coupled to a magnetoplasmadynamic accelerator (MPD arc jet) is described, and the results of preliminary analyses are presented. In this system, the MPD thruster operates intermittently at higher voltages and power levels than the thermionic generating unit. A typical thrust pulse from the MPD arc jet is characterized by power levels of 1 to 4 MWe, a duration of 1 msec, and a duty cycle of approximately 20%. The thermionic generating unit operates continuously but with a lower power level of approximately 0.4 MWe. Energy storage between thrust pulses is provided by building up a large current in an inductor using the output of the thermionic converter array. Periodically, the charging current is interrupted, and the energy stored in the magnetic field of the inductor is utilized for a short duration thrust pulse. The results of the preliminary analysis show that a coupling effectiveness of approximately 85 to 90% is feasible for a nominal 400 KWe system with an inductive unit suitable for a flight vehicle.

Bay Ridge Gardens - Mixed Humid Affordable Multifamily Housing Deep Energy Retrofit: Annapolis, Maryland. Building America Case Study: Whole-House Solutions for Existing Homes (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2013-10-01

Under this project, Newport Partners (as part of the BA-PIRC research team) evaluated the installation, measured performance, and cost-effectiveness of efficiency upgrade measures for a tenant-in-place DER at the Bay Ridge multifamily (MF) development in Annapolis, Maryland. The design and construction phase of the Bay Ridge project was completed in August 2012. This report summarizes system commissioning, short-term test results, utility bill data analysis, and analysis of real-time data collected over a one-year period after the retrofit was complete. The Bay Ridge project is comprised of a "base scope" retrofit which was estimated to achieve a 30%+ savings (relative tomore » pre-retrofit) on 186 apartments, and a "DER scope" which was estimated to achieve 50% savings (relative to pre-retrofit) on a 12-unit building. The base scope was applied to the entire apartment complex, except for one 12-unit building which underwent the DER scope. A wide range of efficiency measures was applied to pursue this savings target for the DER building, including improvements/replacements of mechanical equipment and distribution systems, appliances, lighting and lighting controls, the building envelope, hot water conservation measures, and resident education. The results of this research build upon the current body of knowledge of multifamily retrofits. Towards this end, the research team has collected and generated data on the selection of measures, their estimated performance, their measured performance, and risk factors and their impact on potential measures.« less

Development of an intelligent controller for power generators

NASA Astrophysics Data System (ADS)

Maxted, Clive; Waller, Winston

2005-01-01

This paper is a description of the development of an embedded controller for high power industrial diesel generators. The aim of the project was to replace the existing discrete logic design by an intelligent versatile and user configurable control system. A prototype embedded PC controlled system was developed, capable of fully replacing the existing system, with a colour TFT display and keypad. Features include fully automatic generator control as before with status and alarm display and monitoring of engine parameters, along with data logging, remote communications and a means of analysing data. The unit was tested on the bench and on diesel generators for the core controlling functionality to prove compliance with the specifications. The results of the testing proved the unit's suitability as a replacement for the existing system in its intended environment. The significance of this study is that a low cost replacement solution has been found for an industrial application by transferring modern technological knowledge to a small business. The company are now able to build on the design and take it into production, reducing servicing and production costs.

Bay Ridge Gardens - Mixed-Humid Affordable Multifamily Housing Deep Energy Retrofit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyons, J.; Moore, M.; Thompson, M.

2013-08-01

Under this project, Newport Partners (as part of the BA-PIRC research team) evaluated the installation, measured performance, and cost-effectiveness of efficiency upgrade measures for a tenant-in-place DER at the Bay Ridge multifamily (MF) development in Annapolis, Maryland. The design and construction phase of the Bay Ridge project was completed in August 2012. This report summarizes system commissioning, short-term test results, utility bill data analysis, and analysis of real-time data collected over a one-year period after the retrofit was complete. The Bay Ridge project is comprised of a 'base scope' retrofit which was estimated to achieve a 30%+ savings (relative tomore » pre-retrofit) on 186 apartments, and a 'DER scope' which was estimated to achieve 50% savings (relative to pre-retrofit) on a 12-unit building. The base scope was applied to the entire apartment complex, except for one 12-unit building which underwent the DER scope. A wide range of efficiency measures was applied to pursue this savings target for the DER building, including improvements/replacements of mechanical equipment and distribution systems, appliances, lighting and lighting controls, the building envelope, hot water conservation measures, and resident education. The results of this research build upon the current body of knowledge of multifamily retrofits. Towards this end, the research team has collected and generated data on the selection of measures, their estimated performance, their measured performance, and risk factors and their impact on potential measures.« less

31 CFR Appendix H to Subpart A of... - United States Mint

Code of Federal Regulations, 2011 CFR

2011-07-01

... Act Officer, United States Mint, Judiciary Square Building, 7th floor, 633 3rd Street, NW., Washington... Request, Freedom of Information/Privacy Act Officer, United States Mint, Judiciary Square Building, 7th... Information Appeal, Director, United States Mint, Judiciary Square Building, 7th Floor, 633 3rd Street, NW...

31 CFR Appendix H to Subpart A of... - United States Mint

Code of Federal Regulations, 2013 CFR

2013-07-01

... Act Officer, United States Mint, Judiciary Square Building, 7th floor, 633 3rd Street, NW., Washington... Request, Freedom of Information/Privacy Act Officer, United States Mint, Judiciary Square Building, 7th... Information Appeal, Director, United States Mint, Judiciary Square Building, 7th Floor, 633 3rd Street, NW...

31 CFR Appendix H to Subpart A of... - United States Mint

Code of Federal Regulations, 2012 CFR

2012-07-01

... Act Officer, United States Mint, Judiciary Square Building, 7th floor, 633 3rd Street, NW., Washington... Request, Freedom of Information/Privacy Act Officer, United States Mint, Judiciary Square Building, 7th... Information Appeal, Director, United States Mint, Judiciary Square Building, 7th Floor, 633 3rd Street, NW...

31 CFR Appendix H to Subpart A of... - United States Mint

Code of Federal Regulations, 2014 CFR

2014-07-01

... Act Officer, United States Mint, Judiciary Square Building, 7th floor, 633 3rd Street, NW., Washington... Request, Freedom of Information/Privacy Act Officer, United States Mint, Judiciary Square Building, 7th... Information Appeal, Director, United States Mint, Judiciary Square Building, 7th Floor, 633 3rd Street, NW...

Modeling new coal projects: supercritical or subcritical?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carrino, A.J.; Jones, R.B.

Decisions made on new build coal-fired plants are driven by several factors - emissions, fuel logistics and electric transmission access all provide constraints. The crucial economic decision whether to build supercritical or subcritical units often depends on assumptions concerning the reliability/availability of each technology, the cost of on-fuel operations including maintenance, the generation efficiencies and the potential for emissions credits at some future value. Modeling the influence of these key factors requires analysis and documentation to assure the assets actually meet the projected financial performance. This article addresses some of the issue related to the trade-offs that have the potentialmore » to be driven by the supercritical/subcritical decision. Solomon Associates has been collecting cost, generation and reliability data on coal-fired power generation assets for approximately 10 years using a strict methodology and taxonomy to categorize and compare actual plant operations data. This database provides validated information not only on performance, but also on alternative performance scenarios, which can provide useful insights in the pro forma financial analysis and models of new plants. 1 ref., 1 fig., 3 tabs.« less

Axonal flip-flops and oscillators.

PubMed

Baker, M D

2000-11-01

The strange and unpleasant sensations (paraesthesiae) or asynchronous motor-unit activation (fasciculation) that result from a period of limb ischaemia are examples of ectopic discharge in peripheral nerves. Ectopic activity also results from demyelination and is associated with serious neurological conditions, such as multiple sclerosis. A build-up of extracellular K(+) in the internode and persistent Na(+) currents are now implicated in generating the different forms of activity arising in normal and demyelinated axons.

R&D100: 6.5kV Enhancement-Mode Silicon Carbide JFET Switch

ScienceCinema

Dries, Chris; Hostetler, John; Atcitty, Stan

2018-06-12

Researchers at Sandia National Laboratories have partnered with United Silicon Carbide, Inc. to combine advanced materials with novel manufacturing ideas to build a new product for significantly more efficient power conversion. Harnessing the unique features of silicon carbide, this first of its kind device allows higher voltage switching, and reductions in switching losses to significantly boost the efficiency and reliability of power generation and power conversion.

Modeling of fire smoke movement in multizone garments building using two open source platforms

NASA Astrophysics Data System (ADS)

Khandoker, Md. Arifur Rahman; Galib, Musanna; Islam, Adnan; Rahman, Md. Ashiqur

2017-06-01

Casualty of garment factory workers from factory fire in Bangladesh is a recurring tragedy. Smoke, which is more fatal than fire itself, often propagates through different pathways from lower to upper floors during building fire. Among the toxic gases produced from a building fire, carbon monoxide (CO) can be deadly, even in small amounts. This paper models the propagation and transportation of fire induced smoke (CO) that resulted from the burning of synthetic polyester fibers using two open source platforms, CONTAM and Fire Dynamics Simulator (FDS). Smoke migration in a generic multistoried garment factory building in Bangladesh is modeled using CONTAM where each floor is compartmentalized by different zones. The elevator and stairway shafts are modeled by phantom zones to simulate contaminant (CO) transport from one floor to upper floors. FDS analysis involves burning of two different stacks of polyester jacket of six feet height and with a maximum heat release rate per unit area of 1500kw/m2 over a storage area 50m2 and 150m2, respectively. The resulting CO generation and removal rates from FDS are used in CONTAM to predict fire-borne CO propagation in different zones of the garment building. Findings of the study exhibit that the contaminant flow rate is a strong function of the position of building geometry, location of initiation of fire, amount of burnt material, presence of AHU and contaminant generation and removal rate of CO from the source location etc. The transport of fire-smoke in the building Hallways, stairways and lifts are also investigated in detail to examine the safe egress of the occupants in case of fire.

26 CFR 1.42-16 - Eligible basis reduced by federal grants.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the owner has agreed to maintain as public housing units (PH-units) in the building; (2) Are made with... difference between the rents received from a building's PH-unit tenants and a pro rata portion of the building's actual operating costs that are reasonably allocable to the PH-units (based on square footage...

24 CFR 983.56 - Cap on number of PBV units in each building.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Cap on number of PBV units in each... URBAN DEVELOPMENT PROJECT-BASED VOUCHER (PBV) PROGRAM Selection of PBV Owner Proposals § 983.56 Cap on... single-family building; (ii) Excepted units in a multifamily building. (2) Terms (i) “Excepted units...

26 CFR 1.42-16 - Eligible basis reduced by federal grants.

Code of Federal Regulations, 2013 CFR

2013-04-01

... the owner has agreed to maintain as public housing units (PH-units) in the building; (2) Are made with... difference between the rents received from a building's PH-unit tenants and a pro rata portion of the building's actual operating costs that are reasonably allocable to the PH-units (based on square footage...

26 CFR 1.42-16 - Eligible basis reduced by federal grants.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the owner has agreed to maintain as public housing units (PH-units) in the building; (2) Are made with... difference between the rents received from a building's PH-unit tenants and a pro rata portion of the building's actual operating costs that are reasonably allocable to the PH-units (based on square footage...

26 CFR 1.42-16 - Eligible basis reduced by federal grants.

Code of Federal Regulations, 2012 CFR

2012-04-01

... the owner has agreed to maintain as public housing units (PH-units) in the building; (2) Are made with... difference between the rents received from a building's PH-unit tenants and a pro rata portion of the building's actual operating costs that are reasonably allocable to the PH-units (based on square footage...

26 CFR 1.42-16 - Eligible basis reduced by federal grants.

Code of Federal Regulations, 2014 CFR

2014-04-01

... the owner has agreed to maintain as public housing units (PH-units) in the building; (2) Are made with... difference between the rents received from a building's PH-unit tenants and a pro rata portion of the building's actual operating costs that are reasonably allocable to the PH-units (based on square footage...

11. VIEW NORTH, SOUTH FRONT OF MAIN OFFICE UNIT (BUILDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. VIEW NORTH, SOUTH FRONT OF MAIN OFFICE UNIT (BUILDING I, 2); SOUTH AND EAST FRONTS OF SEED STORAGE BUILDING (BUILDING 21); EAST FRONT OF GREENHOUSE #1 (BUILDING 5) - U.S. Plant Introduction Station, 11601 Old Pond Road, Glenn Dale, Prince George's County, MD

Optical programmable Boolean logic unit.

PubMed

Chattopadhyay, Tanay

2011-11-10

Logic units are the building blocks of many important computational operations likes arithmetic, multiplexer-demultiplexer, radix conversion, parity checker cum generator, etc. Multifunctional logic operation is very much essential in this respect. Here a programmable Boolean logic unit is proposed that can perform 16 Boolean logical operations from a single optical input according to the programming input without changing the circuit design. This circuit has two outputs. One output is complementary to the other. Hence no loss of data can occur. The circuit is basically designed by a 2×2 polarization independent optical cross bar switch. Performance of the proposed circuit has been achieved by doing numerical simulations. The binary logical states (0,1) are represented by the absence of light (null) and presence of light, respectively.

Molecular markers reveal infestation dynamics of the bed bug (Hemiptera: Cimicidae) within apartment buildings.

PubMed

Booth, Warren; Saenz, Virna L; Santangelo, Richard G; Wang, Changlu; Schal, Coby; Vargo, Edward L

2012-05-01

The bed bug, Cimex lectularius L. (Hemiptera: Cimicidae), has experienced an extraordinary global resurgence in recent years, the reasons for which remain poorly understood. Once considered a pest of lower socioeconomic classes, bed bugs are now found extensively across all residential settings, with widespread infestations established in multiapartment buildings. Within such buildings, understanding the population genetic structure and patterns of dispersal may prove critical to the development of effective control strategies. Here, we describe the development of 24 high-resolution microsatellite markers through next generation 454 pyrosequencing and their application to elucidate infestation dynamics within three multistory apartment buildings in the United States. Results reveal contrasting characteristics potentially representative of geographic or locale differences. In Raleigh, NC, an infestation within an apartment building seemed to have started from a single introduction followed by extensive spread. In Jersey City, NJ, two or more introductions followed by spread are evident in two buildings. Populations within single apartments in all buildings were characterized by high levels of relatedness and low levels of diversity, indicative of foundation from small, genetically depauperate propagules. Regardless of the number of unique introductions, genetic data indicate that spread within buildings is extensive, supporting both active and human-mediated dispersal within and between adjacent rooms or apartments spanning multiple floors.

The effectiveness of power-generating complexes constructed on the basis of nuclear power plants combined with additional sources of energy determined taking risk factors into account

NASA Astrophysics Data System (ADS)

Aminov, R. Z.; Khrustalev, V. A.; Portyankin, A. V.

2015-02-01

The effectiveness of combining nuclear power plants equipped with water-cooled water-moderated power-generating reactors (VVER) with other sources of energy within unified power-generating complexes is analyzed. The use of such power-generating complexes makes it possible to achieve the necessary load pickup capability and flexibility in performing the mandatory selective primary and emergency control of load, as well as participation in passing the night minimums of electric load curves while retaining high values of the capacity utilization factor of the entire power-generating complex at higher levels of the steam-turbine part efficiency. Versions involving combined use of nuclear power plants with hydrogen toppings and gas turbine units for generating electricity are considered. In view of the fact that hydrogen is an unsafe energy carrier, the use of which introduces additional elements of risk, a procedure for evaluating these risks under different conditions of implementing the fuel-and-hydrogen cycle at nuclear power plants is proposed. Risk accounting technique with the use of statistical data is considered, including the characteristics of hydrogen and gas pipelines, and the process pipelines equipment tightness loss occurrence rate. The expected intensities of fires and explosions at nuclear power plants fitted with hydrogen toppings and gas turbine units are calculated. In estimating the damage inflicted by events (fires and explosions) occurred in nuclear power plant turbine buildings, the US statistical data were used. Conservative scenarios of fires and explosions of hydrogen-air mixtures in nuclear power plant turbine buildings are presented. Results from calculations of the introduced annual risk to the attained net annual profit ratio in commensurable versions are given. This ratio can be used in selecting projects characterized by the most technically attainable and socially acceptable safety.

Optimization of a hybrid electric power system design for large commercial buildings: An application design guide

NASA Astrophysics Data System (ADS)

Lee, Keun

Renewable energy in different forms has been used in various applications for survival since the beginning of human existence. However, there is a new dire need to reevaluate and recalibrate the overall energy issue both nationally and globally. This includes, but is not limited to, the finite availability of fossil fuel, energy sustainability with an increasing demand, escalating energy costs, environmental impact such as global warming and green-house gases, to name a few. This dissertation is primarily focused and related to the production and usage of electricity from non-hydro renewable sources. Among non-hydro renewable energy sources, electricity generation from wind and solar energy are the fastest-growing technologies in the United States and in the world. However, due to the intermittent nature of such renewable sources, energy storage devices are required to maintain proper operation of the grid system and in order to increase reliability. A hybrid system, as the name suggests, is a combination of different forms of non-renewable and renewable energy generation, with or without storage devices. Hybrid systems, when applied properly, are able to improve reliability and enhance stability, reduce emissions and noise pollution, provide continuous power, increase operation life, reduce cost, and efficiently use all available energy. In the United States (U.S.), buildings consume approximately 40% of the total primary energy and 74% of the total electricity. Therefore, reduction of energy consumption and improved energy efficiency in U.S. buildings will play a vital role in the overall energy picture. Electrical energy usage for any such building varies widely depending on age (construction technique), electricity and natural gas usage, appearance, location and climate. In this research, a hybrid system including non-renewable and renewable energy generation with storage devices specifically for building applications, is studied in detail. This research deals with the optimization of the hybrid system design (which consists of PV panels and/or wind turbines and/or storage devices for building applications) by developing an algorithm designed to make the system cost effective and energy efficient. Input data includes electrical load demand profile of the buildings, buildings' structural and geographical characteristics, real time pricing of electricity, and the costs of hybrid systems and storage devices. When the electrical load demand profile of a building that is being studied is available, a measured demand profile is directly used as input data. However, if that information is not available, a building's electric load demand is estimated using a developed algorithm based on three large data sources from a public domain, and used as input data. Using the acquired input data, the algorithm of this research is designed and programmed in order to determine the size of renewable components and to minimize the total yearly net cost. This dissertation also addresses the parametric sensitivity analysis to determine which factors are more significant and are expected to produce useful guidelines in the decision making process. An engineered and more practical, simplified solution has been provided for the optimized design process.

Generative mechanistic explanation building in undergraduate molecular and cellular biology

NASA Astrophysics Data System (ADS)

Southard, Katelyn M.; Espindola, Melissa R.; Zaepfel, Samantha D.; Bolger, Molly S.

2017-09-01

When conducting scientific research, experts in molecular and cellular biology (MCB) use specific reasoning strategies to construct mechanistic explanations for the underlying causal features of molecular phenomena. We explored how undergraduate students applied this scientific practice in MCB. Drawing from studies of explanation building among scientists, we created and applied a theoretical framework to explore the strategies students use to construct explanations for 'novel' biological phenomena. Specifically, we explored how students navigated the multi-level nature of complex biological systems using generative mechanistic reasoning. Interviews were conducted with introductory and upper-division biology students at a large public university in the United States. Results of qualitative coding revealed key features of students' explanation building. Students used modular thinking to consider the functional subdivisions of the system, which they 'filled in' to varying degrees with mechanistic elements. They also hypothesised the involvement of mechanistic entities and instantiated abstract schema to adapt their explanations to unfamiliar biological contexts. Finally, we explored the flexible thinking that students used to hypothesise the impact of mutations on multi-leveled biological systems. Results revealed a number of ways that students drew mechanistic connections between molecules, functional modules (sets of molecules with an emergent function), cells, tissues, organisms and populations.

Emerging Technologies for Assembly of Microscale Hydrogels

PubMed Central

Kavaz, Doga; Demirel, Melik C.; Demirci, Utkan

2013-01-01

Assembly of cell encapsulating building blocks (i.e., microscale hydrogels) has significant applications in areas including regenerative medicine, tissue engineering, and cell-based in vitro assays for pharmaceutical research and drug discovery. Inspired by the repeating functional units observed in native tissues and biological systems (e.g., the lobule in liver, the nephron in kidney), assembly technologies aim to generate complex tissue structures by organizing microscale building blocks. Novel assembly technologies enable fabrication of engineered tissue constructs with controlled properties including tunable microarchitectural and predefined compositional features. Recent advances in micro- and nano-scale technologies have enabled engineering of microgel based three dimensional (3D) constructs. There is a need for high-throughput and scalable methods to assemble microscale units with a complex 3D micro-architecture. Emerging assembly methods include novel technologies based on microfluidics, acoustic and magnetic fields, nanotextured surfaces, and surface tension. In this review, we survey emerging microscale hydrogel assembly methods offering rapid, scalable microgel assembly in 3D, and provide future perspectives and discuss potential applications. PMID:23184717

Implementation of a Proposed System for Automated Microcode Generation.

DTIC Science & Technology

1984-12-01

Marcia Elaine Provance 6 . PERFORMING ORGANIZATION NAME AND ADDRESS t0. PROGRAM ELEMENT, PROJECT, TASK AREA 6 WORK UNIT NUMBERS * Naval Postgraduate...The proposed microprogramming system is organized around a series of menus which are presented to a microprograrmuer so that she can build FDC 1473... organization is not affected. A computer can also respond more easily to new performance demands and problem solutions. A richer or a larger instruction set

Building A Better Force: Regular Army / Reserve Components Integration In The Army Chemical Corps

DTIC Science & Technology

2016-05-26

the Reserve Components (RCs) assumed sole responsibility for providing the Army with smoke, heavy decontamination, and biological detection ...production of anthrax.20 In 2010, al Qaeda in the Arabian Peninsula urged "brothers with degrees in microbiology or chemistry …to develop a weapon of mass...Army’s generated smoke, heavy decontamination, and biological detection units. This places a greater reliance on the RCs for unique, low density

Characteristics of Private Schools in the United States: Results From the 2007-08 Private School Universe Survey--First Look. NCES 2009-313

ERIC Educational Resources Information Center

Broughman, Stephen P.; Swaim, Nancy L.; Keaton, Patrick W.

2009-01-01

Since 1989, the U.S. Bureau of the Census has conducted the biennial Private School Universe Survey (PSS) for the National Center for Education Statistics (NCES). The PSS is designed to generate biennial data on the total number of private schools, students, and teachers, and to build a universe of private schools in the 50 states and the District…

Final Environmental Statement. Continental United States Over-the- Horizon Backscatter Radar System

DTIC Science & Technology

1975-01-01

plants will be provided only for the operational radar system. When operating they will emit diesel exhaust fumes into the atmosphere. g. Noise...Pollution. Noise will be generated when the standby power plants are used. h. Foliage and Soil. The clearing of trees and shrubs in the...building, a 12 megawatt standby power plant , a gate house, transmit antennas, connection to commercial power lines, a paved access road, a well water

Aspergillosis in immunocompromised paediatric patients: associations with building hygiene, design, and indoor air.

PubMed Central

Anderson, K.; Morris, G.; Kennedy, H.; Croall, J.; Michie, J.; Richardson, M. D.; Gibson, B.

1996-01-01

BACKGROUND: Nosocomial aspergillosis is a well known complication of immunosuppression in cancer patients and those undergoing transplantation and has usually been associated with major building construction or demolition. An observational study is reported of the hospital environment associated with an outbreak of aspergillosis in a paediatric oncology ward. METHODS: All cases of aspergillosis were identified from the hospital records and categorised as definite or probable according to the extent of supportive clinical and laboratory findings. All relevant aspects of building ventilation, air filtration, and aerosol generation considered relevant were examined and air samples for fungi were taken in triplicate at 25 sites using a slit sampler with appropriate culture media. RESULTS: Six cases of aspergillosis were identified over one year out of the 148 patients who attended the unit - the only part of the hospital where cases were found. Examination of the building services and function suggested that the cause or source was isolated to this paediatric oncology/haematology ward and may have been attributed to a defective disposal conduit door as well as the dispersal of a contaminated aerosol from the ward vacuum cleaner which had the highest measured concentrations of Aspergillus fumigatus in or around the building (65 colony forming units (cfu)/m3 compared with 0-6 cfu/m3 elsewhere). No further cases were identified in the two years after these hygiene arrangements were changed. CONCLUSIONS: The investigation of this outbreak of nosocomial aspergillosis identified several possible sources of fungally contaminated aerosol which could have been implicated as the cause. Their modification was followed by a reduction in the incidence of further cases. Each should be incorporated as an issue of importance in hospital building design and hygiene. PMID:8779127

STEAM PLANT, TRA609. SECTION A SHOWS FEATURES OF NORTH/SOUTH AXIS: ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

STEAM PLANT, TRA-609. SECTION A SHOWS FEATURES OF NORTH/SOUTH AXIS: STEAM GENERATOR AND CATWALK, STACK, DEGREASER FEED WATER HEATER IN PENTHOUSE, MEZZANINE, SURGE TANK PIT (BELOW GROUND LEVEL). UTILITY ROOM SHOWS DIESEL ENGINE GENERATORS, AIR TANKS, STARTING AIR COMPRESSORS. OUTSIDE SOUTH END ARE EXHAUST MUFFLER, AIR INTAKE OIL FILTER, RADIATOR COOLING UNIT, AIR SURGE TANK. SECTION B CROSSES WEST TO EAST NEAR SOUTH END OF BUILDING TO SHOW ARRANGEMENT OF DIESEL ENGINE GENERATOR, AIR DRIER, AFTER COOLER, AIR COMPRESSOR, AND BLOWDOWN TANK. BLAW-KNOX 3150-9-2, 6/1950. INL INDEX NO. 431-0609-00-098-100018, REV. 3. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

DOE Office of Scientific and Technical Information (OSTI.GOV)

NSTec Environmental Management

The proposed Mixed Waste Storage Unit (MWSU) will be located within the Area 5 Radioactive Waste Management Complex (RWMC). Existing facilities at the RWMC will be used to store low-level mixed waste (LLMW). Storage is required to accommodate offsite-generated LLMW shipped to the Nevada Test Site (NTS) for disposal in the new Mixed Waste Disposal Unit (MWDU) currently in the design/build stage. LLMW generated at the NTS (onsite) is currently stored on the Transuranic (TRU) Pad (TP) in Area 5 under a Mutual Consent Agreement (MCA) with the Nevada Division of Environmental Protection, Bureau of Federal Facilities (NDEP/BFF). When themore » proposed MWSU is permitted, the U.S. Department of Energy (DOE) will ask that NDEP revoke the MCA and onsite-generated LLMW will fall under the MWSU permit terms and conditions. The unit will also store polychlorinated biphenyl (PCB) waste and friable and non-friable asbestos waste that meets the acceptance criteria in the Waste Analysis Plan (Exhibit 2) for disposal in the MWDU. In addition to Resource Conservation and Recovery Act (RCRA) requirements, the proposed MWSU will also be subject to Department of Energy (DOE) orders and other applicable state and federal regulations. Table 1 provides the metric conversion factors used in this application. Table 2 provides a list of existing permits. Table 3 lists operational RCRA units at the NTS and their respective regulatory status.« less

BUILDING A PLATFORM FOR TRANSLATIONAL RESEARCH IN CHRONIC NON-COMMUNICABLE DISEASES TO ADDRESS POPULATION HEALTH IN PERU

PubMed Central

Miranda, J. Jaime; Bernabé-Ortiz, Antonio; Diez-Canseco, Francisco; Málaga, Germán; Cardenas, María K.; Carrillo-Larco, Rodrigo M.; Pesantes, M. Amalia; Araya, Ricardo; Boggio, Oscar; Checkley, William; García, Patricia J.; León-Velarde, Fabiola; Lescano, Andrés G.; Montori, Victor; Pan, William; Rivera-Chira, Maria; Sacksteder, Katherine; Smeeth, Liam; García, Héctor H.; Gilman, Robert H.

2014-01-01

The CRONICAS Centre of Excellence in Chronic Diseases, based at Universidad Peruana Cayetano Heredia, was created in 2009 with support from the United States National Heart, Lung, and Blood Institute (NHLBI). The vision of CRONICAS is to build a globally recognised Centre of Excellence conducting quality and innovative research and generating high-impact evidence for health. The Centre’s identity is embedded in its core values: generosity, innovation, integrity, and quality. This review has been structured to describe the development of the CRONICAS Centre, with a focus on highlighting the ongoing translational research projects and capacity building strategies. The CRONICAS Centre of Excellence is not a risk-averse organisation: it benefits from past experiences, including past mistakes, and improves upon them, and thus challenges traditional research approaches. This ethos and environment is key to fostering innovation in research. PMID:25754562

INNOVATIVE HYBRID GAS/ELECTRIC CHILLER COGENERATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Todd Kollross; Mike Connolly

2004-06-30

Engine-driven chillers are quickly gaining popularity in the market place (increased from 7,000 tons in 1994 to greater than 50,000 tons in 1998) due to their high efficiency, electric peak shaving capability, and overall low operating cost. The product offers attractive economics (5 year pay back or less) in many applications, based on areas cooling requirements and electric pricing structure. When heat is recovered and utilized from the engine, the energy resource efficiency of a natural gas engine-driven chiller is higher than all competing products. As deregulation proceeds, real time pricing rate structures promise high peak demand electric rates, butmore » low off-peak electric rates. An emerging trend with commercial building owners and managers who require air conditioning today is to reduce their operating costs by installing hybrid chiller systems that combine gas and electric units. Hybrid systems not only reduce peak electric demand charges, but also allow customers to level their energy load profiles and select the most economical energy source, gas or electricity, from hour to hour. Until recently, however, all hybrid systems incorporated one or more gas-powered chillers (engine driven and/or absorption) and one or more conventional electric units. Typically, the cooling capacity of hybrid chiller plants ranges from the hundreds to thousands of refrigeration tons, with multiple chillers affording the user a choice of cooling systems. But this flexibility is less of an option for building operators who have limited room for equipment. To address this technology gap, a hybrid chiller was developed by Alturdyne that combines a gas engine, an electric motor and a refrigeration compressor within a single package. However, this product had not been designed to realize the full features and benefits possible by combining an engine, motor/generator and compressor. The purpose of this project is to develop a new hybrid chiller that can (1) reduce end-user energy costs, (2) lower building peak electric load, (3) increase energy efficiency, and (4) provide standby power. This new hybrid product is designed to allow the engine to generate electricity or drive the chiller's compressor, based on the market price and conditions of the available energy sources. Building owners can minimize cooling costs by operating with natural gas or electricity, depending on time of day energy rates. In the event of a backout, the building owner could either operate the product as a synchronous generator set, thus providing standby power, or continue to operate a chiller to provide air conditioning with support of a small generator set to cover the chiller's electric auxiliary requirements. The ability to utilize the same piece of equipment as a hybrid gas/electric chiller or a standby generator greatly enhances its economic attractiveness and would substantially expand the opportunities for high efficiency cooling products.« less

Building energy analysis tool

DOEpatents

Brackney, Larry; Parker, Andrew; Long, Nicholas; Metzger, Ian; Dean, Jesse; Lisell, Lars

2016-04-12

A building energy analysis system includes a building component library configured to store a plurality of building components, a modeling tool configured to access the building component library and create a building model of a building under analysis using building spatial data and using selected building components of the plurality of building components stored in the building component library, a building analysis engine configured to operate the building model and generate a baseline energy model of the building under analysis and further configured to apply one or more energy conservation measures to the baseline energy model in order to generate one or more corresponding optimized energy models, and a recommendation tool configured to assess the one or more optimized energy models against the baseline energy model and generate recommendations for substitute building components or modifications.

Eight-Year Summary of Fort Irwin, CA, Family Housing Comparison Test: Operation and Maintenance Costs of Manufactured vs. Conventionally Built Units

DTIC Science & Technology

1993-07-01

Ruptured polybutylene pipe from Building 3858, Unit C 77 F20 Longitudinal hair line crack in PB pipe from Building 3802, Unit B 78 F21 Microscopic...of the 200 housing units used national standards in the unit construction which included the use of polybutylene ( PB ) piping. The piping was...in PB Pipe from Building 3802, Unit B Figure F 21: Microscopic View of Longitudinal Hair Line Crack 78 Figure F22: White Coating on Acetld Fitting

An Estimation of Construction and Demolition Debris in Seoul, Korea: Waste Amount, Type, and Estimating Model.

PubMed

Seo, Seongwon; Hwang, Yongwoo

1999-08-01

Construction and demolition (C&D) debris is generated at the site of various construction activities. However, the amount of the debris is usually so large that it is necessary to estimate the amount of C&D debris as accurately as possible for effective waste management and control in urban areas. In this paper, an effective estimation method using a statistical model was proposed. The estimation process was composed of five steps: estimation of the life span of buildings; estimation of the floor area of buildings to be constructed and demolished; calculation of individual intensity units of C&D debris; and estimation of the future C&D debris production. This method was also applied in the city of Seoul as an actual case, and the estimated amount of C&D debris in Seoul in 2021 was approximately 24 million tons. Of this total amount, 98% was generated by demolition, and the main components of debris were concrete and brick.

Simple approach in understanding interzeolite transformations using ring building units

NASA Astrophysics Data System (ADS)

Suhendar, D.; Buchari; Mukti, R. R.; Ismunandar

2018-04-01

Recently, there are two general approaches used in understanding interzeolite transformations, thermodynamically represented by framework density (FD) and kinetically by structural building units. Two types of structural building units are composite building units (CBU’s) and secondary building units (SBU’s). This study aims to examine the approaches by using interzeolite transformation data available in literature and propose a possible alternative approach. From a number of cases of zeolite transformation, the FD and CBU approach are not suitable for use. The FD approach fails in cases involving zeolite parents that have moderate or high FD’s, while CBU approach fails because of CBU’s unavailability in parent zeolites compared with CBU’s in their transformation products. The SBU approach is most likely to fit because SBU’s are units that have basic form of ring structures and closer to the state and shape of oligomeric fragments present in zeolite synthesis or dissolution cases. Thus, a new approach can be considered in understanding the interzeolite transformation, namely the ring building unit (RBU) approach. The advantage of RBU approach is RBU’s can be easily derived from all framework types, but in SBU approach there are several types of frameworks that cannot be expressed in SBU forms.

Simulation and visualization of energy-related occupant behavior in office buildings

DOE PAGES

Chen, Yixing; Liang, Xin; Hong, Tianzhen; ...

2017-03-15

In current building performance simulation programs, occupant presence and interactions with building systems are over-simplified and less indicative of real world scenarios, contributing to the discrepancies between simulated and actual energy use in buildings. Simulation results are normally presented using various types of charts. However, using those charts, it is difficult to visualize and communicate the importance of occupants’ behavior to building energy performance. This study introduced a new approach to simulating and visualizing energy-related occupant behavior in office buildings. First, the Occupancy Simulator was used to simulate the occupant presence and movement and generate occupant schedules for each spacemore » as well as for each occupant. Then an occupant behavior functional mockup unit (obFMU) was used to model occupant behavior and analyze their impact on building energy use through co-simulation with EnergyPlus. Finally, an agent-based model built upon AnyLogic was applied to visualize the simulation results of the occupant movement and interactions with building systems, as well as the related energy performance. A case study using a small office building in Miami, FL was presented to demonstrate the process and application of the Occupancy Simulator, the obFMU and EnergyPlus, and the AnyLogic module in simulation and visualization of energy-related occupant behaviors in office buildings. Furthermore, the presented approach provides a new detailed and visual way for policy makers, architects, engineers and building operators to better understand occupant energy behavior and their impact on energy use in buildings, which can improve the design and operation of low energy buildings.« less

Simulation and visualization of energy-related occupant behavior in office buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Yixing; Liang, Xin; Hong, Tianzhen

In current building performance simulation programs, occupant presence and interactions with building systems are over-simplified and less indicative of real world scenarios, contributing to the discrepancies between simulated and actual energy use in buildings. Simulation results are normally presented using various types of charts. However, using those charts, it is difficult to visualize and communicate the importance of occupants’ behavior to building energy performance. This study introduced a new approach to simulating and visualizing energy-related occupant behavior in office buildings. First, the Occupancy Simulator was used to simulate the occupant presence and movement and generate occupant schedules for each spacemore » as well as for each occupant. Then an occupant behavior functional mockup unit (obFMU) was used to model occupant behavior and analyze their impact on building energy use through co-simulation with EnergyPlus. Finally, an agent-based model built upon AnyLogic was applied to visualize the simulation results of the occupant movement and interactions with building systems, as well as the related energy performance. A case study using a small office building in Miami, FL was presented to demonstrate the process and application of the Occupancy Simulator, the obFMU and EnergyPlus, and the AnyLogic module in simulation and visualization of energy-related occupant behaviors in office buildings. Furthermore, the presented approach provides a new detailed and visual way for policy makers, architects, engineers and building operators to better understand occupant energy behavior and their impact on energy use in buildings, which can improve the design and operation of low energy buildings.« less

Wood products used in the construction of low-rise nonresidential buildings in the United States, 2008

Treesearch

David McKeever

2010-01-01

Low-rise nonresidential building construction is an important market for lumber, structural wood panels, nonstructural wood panels, and engineered wood products in the United States. This report examines low-rise nonresidential buildings of four or fewer stories only. Buildings with five or more stories are normally severely restricted by building code from being wood...

Wood products used in the construction of low-rise nonresidential buildings in the United States, 2003

Treesearch

David B. McKeever; Craig Adair; Jennifer O' Connor

2005-01-01

Low-rise nonresidential building construction is an important market for lumber, structural wood panels, nonstructural wood panels, and engineered wood products in the United States. This report examines low-rise nonresidential buildings of four or fewer stories only, because buildings with five or more stories are normally severely restricted by building code from...

Building Energy Modeling and Control Methods for Optimization and Renewables Integration

NASA Astrophysics Data System (ADS)

Burger, Eric M.

This dissertation presents techniques for the numerical modeling and control of building systems, with an emphasis on thermostatically controlled loads. The primary objective of this work is to address technical challenges related to the management of energy use in commercial and residential buildings. This work is motivated by the need to enhance the performance of building systems and by the potential for aggregated loads to perform load following and regulation ancillary services, thereby enabling the further adoption of intermittent renewable energy generation technologies. To increase the generalizability of the techniques, an emphasis is placed on recursive and adaptive methods which minimize the need for customization to specific buildings and applications. The techniques presented in this dissertation can be divided into two general categories: modeling and control. Modeling techniques encompass the processing of data streams from sensors and the training of numerical models. These models enable us to predict the energy use of a building and of sub-systems, such as a heating, ventilation, and air conditioning (HVAC) unit. Specifically, we first present an ensemble learning method for the short-term forecasting of total electricity demand in buildings. As the deployment of intermittent renewable energy resources continues to rise, the generation of accurate building-level electricity demand forecasts will be valuable to both grid operators and building energy management systems. Second, we present a recursive parameter estimation technique for identifying a thermostatically controlled load (TCL) model that is non-linear in the parameters. For TCLs to perform demand response services in real-time markets, online methods for parameter estimation are needed. Third, we develop a piecewise linear thermal model of a residential building and train the model using data collected from a custom-built thermostat. This model is capable of approximating unmodeled dynamics within a building by learning from sensor data. Control techniques encompass the application of optimal control theory, model predictive control, and convex distributed optimization to TCLs. First, we present the alternative control trajectory (ACT) representation, a novel method for the approximate optimization of non-convex discrete systems. This approach enables the optimal control of a population of non-convex agents using distributed convex optimization techniques. Second, we present a distributed convex optimization algorithm for the control of a TCL population. Experimental results demonstrate the application of this algorithm to the problem of renewable energy generation following. This dissertation contributes to the development of intelligent energy management systems for buildings by presenting a suite of novel and adaptable modeling and control techniques. Applications focus on optimizing the performance of building operations and on facilitating the integration of renewable energy resources.

Interim Closure Activities at Corrective Action Unit 114: Area 25 EMAD Facility, Nevada National Security Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boehlecke, R. F.

This letter report documents interim activities that have been completed at CAU 114 to support ongoing access and generate information necessary to plan future closure activities. General housekeeping and cleanup of debris was conducted in the EMAD yard, cold bays, support areas of Building 3900, and postmortem cell tunnel area of the hot bay. All non-asbestos ceiling tiles and loose and broken non-friable asbestos floor tiles were removed from support galleries and office areas. Non-radiologically contaminated piping and equipment in the cold areas of the building and in the two 120-ton locomotives in the yard were tapped, characterized, drained, andmore » verified free of contents.« less

Fusion of LIDAR Data and Multispectral Imagery for Effective Building Detection Based on Graph and Connected Component Analysis

NASA Astrophysics Data System (ADS)

Gilani, S. A. N.; Awrangjeb, M.; Lu, G.

2015-03-01

Building detection in complex scenes is a non-trivial exercise due to building shape variability, irregular terrain, shadows, and occlusion by highly dense vegetation. In this research, we present a graph based algorithm, which combines multispectral imagery and airborne LiDAR information to completely delineate the building boundaries in urban and densely vegetated area. In the first phase, LiDAR data is divided into two groups: ground and non-ground data, using ground height from a bare-earth DEM. A mask, known as the primary building mask, is generated from the non-ground LiDAR points where the black region represents the elevated area (buildings and trees), while the white region describes the ground (earth). The second phase begins with the process of Connected Component Analysis (CCA) where the number of objects present in the test scene are identified followed by initial boundary detection and labelling. Additionally, a graph from the connected components is generated, where each black pixel corresponds to a node. An edge of a unit distance is defined between a black pixel and a neighbouring black pixel, if any. An edge does not exist from a black pixel to a neighbouring white pixel, if any. This phenomenon produces a disconnected components graph, where each component represents a prospective building or a dense vegetation (a contiguous block of black pixels from the primary mask). In the third phase, a clustering process clusters the segmented lines, extracted from multispectral imagery, around the graph components, if possible. In the fourth step, NDVI, image entropy, and LiDAR data are utilised to discriminate between vegetation, buildings, and isolated building's occluded parts. Finally, the initially extracted building boundary is extended pixel-wise using NDVI, entropy, and LiDAR data to completely delineate the building and to maximise the boundary reach towards building edges. The proposed technique is evaluated using two Australian data sets: Aitkenvale and Hervey Bay, for object-based and pixel-based completeness, correctness, and quality. The proposed technique detects buildings larger than 50 m2 and 10 m2 in the Aitkenvale site with 100% and 91% accuracy, respectively, while in the Hervey Bay site it performs better with 100% accuracy for buildings larger than 10 m2 in area.

Prevention and control of noncommunicable diseases through evidence-based public health: implementing the NCD 2020 action plan.

PubMed

Diem, Günter; Brownson, Ross C; Grabauskas, Vilius; Shatchkute, Aushra; Stachenko, Sylvie

2016-09-01

The control of noncommunicable diseases (NCDs) was addressed by the declaration of the 66th United Nations (UN) General Assembly followed by the World Health Organization's (WHO) NCD 2020 action plan. There is a clear need to better apply evidence in public health settings to tackle both behaviour-related factors and the underlying social and economic conditions. This article describes concepts of evidence-based public health (EBPH) and outlines a set of actions that are essential for successful global NCD prevention. The authors describe the importance of knowledge translation with the goal of increasing the effectiveness of public health services, relying on both quantitative and qualitative evidence. In particular, the role of capacity building is highlighted because it is fundamental to progress in controlling NCDs. Important challenges for capacity building include the need to bridge diverse disciplines, build the evidence base across countries and the lack of formal training in public health sciences. As brief case examples, several successful capacity-building efforts are highlighted to address challenges and further evidence-based decision making. The need for a more comprehensive public health approach, addressing social, environmental and cultural conditions, has led to government-wide and society-wide strategies that are now on the agenda due to efforts such as the WHO's NCD 2020 action plan and Health 2020: the European Policy for Health and Wellbeing. These efforts need research to generate evidence in new areas (e.g. equity and sustainability), training to build public health capacity and a continuous process of improvement and knowledge generation and translation. © The Author(s) 2015.

Three essays of economics and policy on renewable energy and energy efficiency

NASA Astrophysics Data System (ADS)

Meng, Yuxi

In face of the crisis in energy security, environmental contamination, and climate change, energy saving and carbon emission reduction have become the top concerns of the whole human world. To address those concerns, renewable energy and energy efficiency are the two fields that many countries are paying attention to, which are also my research focus. The dissertation consists of three papers, including the innovation behavior of renewable energy producers, the impact of renewable energy policy on renewable innovation, and the market feedback to energy efficient building benchmarking ordinance. Here are the main conclusions I have reached in this dissertation. First, through the study on foreign patenting intention with the case study of Chinese solar PV industry, I looked at the patenting behaviors of 15 non-Chinese solar PV producers in solar PV technologies in China, and pointed out that foreign firms may file patents in the home country or production base of their competitors in order to earn the competitive edge in the global market. The second study is about the "Innovation by Generating" process. I specifically focused on Renewable Portfolio Standard (RPS) in the United States and the innovation performance within each state, and found out that wind power generation in RPS states has developed rapidly after the adoption of RPS, while the "Innovating by Generating" effect is more significant in solar PV technologies. In general, the innovations of the two technology groups are not prominently encouraged by RPS. My last study is about the benchmarking law and market response in the scenario of Philadelphia Benchmarking Law. By comparing the rental rate of LEED/EnergyStar buildings and ordinary buildings in the city of Philadelphia before and after the adoption of the building energy efficiency benchmarking law, I believe that the passage of Philadelphia Benchmarking Law may be helpful in improving the public awareness and understanding of energy efficiency information of buildings.

24 CFR 983.56 - Cap on number of PBV units in each building.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Cap on number of PBV units in each... URBAN DEVELOPMENT PROJECT-BASED VOUCHER (PBV) PROGRAM Selection of PBV Owner Proposals § 983.56 Cap on number of PBV units in each building. (a) 25 percent per building cap. Except as provided in paragraph (b...

Planning, Designing, Building, and Moving a Large Volume Maternity Service to a New Labor and Birth Unit.

PubMed

Thompson, Heather; Legorreta, Kimberly; Maher, Mary Ann; Lavin, Melanie M

Our health system recognized the need to update facility space and associated technology for the labor and birth unit within our large volume perinatal service to improve the patient experience, and enhance safety, quality of care, and staff satisfaction. When an organization decides to invest $30 million dollars in a construction project such as a new labor and birth unit, many factors and considerations are involved. Financial support, planning, design, and construction phases of building a new unit are complex and therefore require strong interdisciplinary collaboration, leadership, and project management. The new labor and birth unit required nearly 3 years of planning, designing, and construction. Patient and family preferences were elicited through consumer focus groups. Multiple meetings with the administrative and nursing leadership teams, staff nurses, nurse midwives, and physicians were held to generate ideas for improvement in the new space. Involving frontline clinicians and childbearing women in the process was critical to success. The labor and birth unit moved to a new patient tower in a space that was doubled in square footage and geographically now on three separate floors. In the 6 months prior to the move, many efforts were made in our community to share our new space. The marketing strategy was very detailed and creative with ongoing input from the nursing leadership team. The nursing staff was involved in every step along the way. It was critical to have champions as workflow teams emerged. We hosted simulation drills and tested scenarios with new workflows. Move day was rehearsed with representatives of all members of the perinatal team participating. These efforts ultimately resulted in a move time of ~5 hours. Birth volumes increased 7% within the first 6 months. After 3 years in our new space, our birth volumes have risen nearly 15% and are still growing. Key processes and roles responsible for a successful build, efficient and safe move day, and optimal operational utility, as anticipated, of a new labor and birth unit in a large volume perinatal service are detailed.

75 FR 63404 - Fossil Fuel-Generated Energy Consumption Reduction for New Federal Buildings and Major...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-15

... [Docket No. EERE-2010-BT-STD-0031] RIN 1904-AB96 Fossil Fuel-Generated Energy Consumption Reduction for... of fossil fuel-generated energy consumption in new Federal buildings and Federal buildings undergoing... full fossil fuel-generated energy consumption reduction level is technically impracticable in light of...

Improving STEM Education and Workforce Development by the Inclusion of Research Experiences in the Curriculum at SWC

DTIC Science & Technology

2016-06-08

server environment. While the college’s two Cisco blade -servers are located in separate buildings, these 1. REPORT DATE (DD-MM-YYYY) 4. TITLE AND...college’s two Cisco blade -servers are located in separate buildings, these units now work as one unit. Critical databases and software packages are...server environment. While the college’s two Cisco blade -servers are located in separate buildings, these units now work as one unit. Critical

Design, evaluation and recommedation effort relating to the modification of a residential 3-ton absorption cycle cooling unit for operation with solar energy

NASA Technical Reports Server (NTRS)

Merrick, R. H.; Anderson, P. P.

1973-01-01

The possible use of solar energy powered absorption units to provide cooling and heating of residential buildings is studied. Both, the ammonia-water and the water-lithium bromide cycles, are considered. It is shown that the air cooled ammonia water unit does not meet the criteria for COP and pump power on the cooling cycle and the heat obtained from it acting as a heat pump is at too low a temperature. If the ammonia machine is water cooled it will meet the design criteria for cooling but can not supply the heating needs. The water cooled lithium bromide unit meets the specified performance for cooling with appreciably lower generator temperatures and without a mechanical solution pump. It is recommeded that in the demonstration project a direct expansion lithium bromide unit be used for cooling and an auxiliary duct coil using the solar heated water be employed for heating.

Geomorphic Unit Tool (GUT): Applications of Fluvial Mapping

NASA Astrophysics Data System (ADS)

Kramer, N.; Bangen, S. G.; Wheaton, J. M.; Bouwes, N.; Wall, E.; Saunders, C.; Bennett, S.; Fortney, S.

2017-12-01

Geomorphic units are the building blocks of rivers and represent distinct habitat patches for many fluvial organisms. We present the Geomorphic Unit Toolkit (GUT), a flexible GIS geomorphic unit mapping tool, to generate maps of fluvial landforms from topography. GUT applies attributes to landforms based on flow stage (Tier 1), topographic signatures (Tier 2), geomorphic characteristics (Tier 3) and patch characteristics (Tier 4) to derive attributed maps at the level of detail required by analysts. We hypothesize that if more rigorous and consistent geomorphic mapping is conducted, better correlations between physical habitat units and ecohydraulic model results will be obtained compared to past work. Using output from GUT for coarse bed tributary streams in the Columbia River Basin, we explore relationships between salmonid habitat and geomorphic spatial metrics. We also highlight case studies of how GUT can be used to showcase geomorphic impact from large wood restoration efforts. Provided high resolution topography exists, this tool can be used to quickly assess changes in fluvial geomorphology in watersheds impacted by human activities.

Automatic 3d Building Model Generations with Airborne LiDAR Data

NASA Astrophysics Data System (ADS)

Yastikli, N.; Cetin, Z.

2017-11-01

LiDAR systems become more and more popular because of the potential use for obtaining the point clouds of vegetation and man-made objects on the earth surface in an accurate and quick way. Nowadays, these airborne systems have been frequently used in wide range of applications such as DEM/DSM generation, topographic mapping, object extraction, vegetation mapping, 3 dimensional (3D) modelling and simulation, change detection, engineering works, revision of maps, coastal management and bathymetry. The 3D building model generation is the one of the most prominent applications of LiDAR system, which has the major importance for urban planning, illegal construction monitoring, 3D city modelling, environmental simulation, tourism, security, telecommunication and mobile navigation etc. The manual or semi-automatic 3D building model generation is costly and very time-consuming process for these applications. Thus, an approach for automatic 3D building model generation is needed in a simple and quick way for many studies which includes building modelling. In this study, automatic 3D building models generation is aimed with airborne LiDAR data. An approach is proposed for automatic 3D building models generation including the automatic point based classification of raw LiDAR point cloud. The proposed point based classification includes the hierarchical rules, for the automatic production of 3D building models. The detailed analyses for the parameters which used in hierarchical rules have been performed to improve classification results using different test areas identified in the study area. The proposed approach have been tested in the study area which has partly open areas, forest areas and many types of the buildings, in Zekeriyakoy, Istanbul using the TerraScan module of TerraSolid. The 3D building model was generated automatically using the results of the automatic point based classification. The obtained results of this research on study area verified that automatic 3D building models can be generated successfully using raw LiDAR point cloud data.

75 FR 66008 - Fossil Fuel-Generated Energy Consumption Reduction for New Federal Buildings and Major...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-27

... Fossil Fuel-Generated Energy Consumption Reduction for New Federal Buildings and Major Renovations of Federal Buildings; Correction AGENCY: Office of Energy Efficiency and Renewable Energy, Department of... the fossil fuel- generated energy consumption [[Page 66009

Americium As A Potential Power Source For Space Missions

NASA Astrophysics Data System (ADS)

Cordingley, Leon; Rice, Tom; Sarsfield, Mark J.; Stephenson, Keith; Tinsley, Tim

2011-10-01

Electrical power sources used in outer planet missions are a key enabling technology for data acquisition and communications. Power sources generate electricity from the thermal energy from alpha decay of the radioisotope 238Pu via thermoelectric conversion. Production of 238Pu requires specialist facilities including a nuclear reactor and reprocessing plants that are expensive to build and operate, so naturally, a more economical alternative is attractive to the industry. Within Europe 241Am is a feasible alternative to 238Pu that can provide a heat source for radioisotope thermoelectric generators (RTGs) and radioisotope heating units (RHUs). Whilst there are implications associated with the differences between 238Pu and 241Am, these technological challenges are surmountable.

Research Proposal for the Design and Engineering Phase of a Solar Heating and Cooling System Experiment at the Warner Robins Public Library, Warner Robins, Georgia. Submitted to the United States Energy Research and Development Administration.

ERIC Educational Resources Information Center

Phillips, Warren H.; And Others

A number of reasons are advanced to include a solar heating and cooling experiment in a library building. The unique aspects of the experiment are to be a seasonally adjustable collector tilt and testing of a new generation of absorption air conditioners. After a brief description of the proposed experiment, the proposal contains forms filed by…

JPSS-1 Delta II Interstage Hoisted from Horizontal and Rotated to Vertical for Transport

NASA Image and Video Library

2016-07-06

The interstage section of the United Launch Alliance Delta II rocket that will launch the Joint Polar Satellite System-1 (JPSS-1) is hoisted to vertical in Building 836 on Vandenberg Air Force Base in California. JPSS, a next-generation environmental satellite system, is a collaborative program between the National Oceanic and Atmospheric Administration (NOAA) and NASA. Launch is targeted for March 27, 2017. To learn more about JPSS-1, visit www.jpss.noaa.gov.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shehabi, Arman; Ganeshalingam, Mohan; DeMates, Lauren

Laboratories are estimated to be 3-5 times more energy intensive than typical office buildings and offer significant opportunities for energy use reductions. Although energy intensity varies widely, laboratories are generally energy intensive due to ventilation requirements, the research instruments used, and other health and safety concerns. Because the requirements of laboratory facilities differ so dramatically from those of other buildings, a clear need exists for an initiative exclusively targeting these facilities. The building stock of laboratories in the United States span different economic sectors, include governmental and academic institution, and are often defined differently by different groups. Information on laboratorymore » buildings is often limited to a small subsection of the total building stock making aggregate estimates of the total U.S. laboratories and their energy use challenging. Previous estimates of U.S. laboratory space vary widely owing to differences in how laboratories are defined and categorized. A 2006 report on fume hoods provided an estimate of 150,000 laboratories populating the U.S. based in part on interviews of industry experts, however, a 2009 analysis of the 2003 Commercial Buildings Energy Consumption Survey (CBECS) generated an estimate of only 9,000 laboratory buildings. This report draws on multiple data sources that have been evaluated to construct an understanding of U.S. laboratories across different sizes and markets segments. This 2016 analysis is an update to draft reports released in October and December 2016.« less

Preserving Envelope Efficiency in Performance Based Code Compliance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thornton, Brian A.; Sullivan, Greg P.; Rosenberg, Michael I.

2015-06-20

The City of Seattle 2012 Energy Code (Seattle 2014), one of the most progressive in the country, is under revision for its 2015 edition. Additionally, city personnel participate in the development of the next generation of the Washington State Energy Code and the International Energy Code. Seattle has pledged carbon neutrality by 2050 including buildings, transportation and other sectors. The United States Department of Energy (DOE), through Pacific Northwest National Laboratory (PNNL) provided technical assistance to Seattle in order to understand the implications of one potential direction for its code development, limiting trade-offs of long-lived building envelope components less stringentmore » than the prescriptive code envelope requirements by using better-than-code but shorter-lived lighting and heating, ventilation, and air-conditioning (HVAC) components through the total building performance modeled energy compliance path. Weaker building envelopes can permanently limit building energy performance even as lighting and HVAC components are upgraded over time, because retrofitting the envelope is less likely and more expensive. Weaker building envelopes may also increase the required size, cost and complexity of HVAC systems and may adversely affect occupant comfort. This report presents the results of this technical assistance. The use of modeled energy code compliance to trade-off envelope components with shorter-lived building components is not unique to Seattle and the lessons and possible solutions described in this report have implications for other jurisdictions and energy codes.« less

Age effect in generating mental images of buildings but not common objects.

PubMed

Piccardi, L; Nori, R; Palermo, L; Guariglia, C; Giusberti, F

2015-08-18

Imagining a familiar environment is different from imagining an environmental map and clinical evidence demonstrated the existence of double dissociations in brain-damaged patients due to the contents of mental images. Here, we assessed a large sample of young and old participants by considering their ability to generate different kinds of mental images, namely, buildings or common objects. As buildings are environmental stimuli that have an important role in human navigation, we expected that elderly participants would have greater difficulty in generating images of buildings than common objects. We found that young and older participants differed in generating both buildings and common objects. For young participants there were no differences between buildings and common objects, but older participants found easier to generate common objects than buildings. Buildings are a special type of visual stimuli because in urban environments they are commonly used as landmarks for navigational purposes. Considering that topographical orientation is one of the abilities mostly affected in normal and pathological aging, the present data throw some light on the impaired processes underlying human navigation. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Wood and Other Materials Used to Construct Nonresidential Buildings in the United States 2011

Treesearch

Craig Adair; David B. McKeever; Chris Gaston; Margaret Stewart

2013-01-01

The construction of low-rise nonresidential buildings is an important market for lumber, engineered wood products, and structural and nonstructural wood panels in the United States. This report examines low-rise nonresidential buildings of six or fewer stories. Those with more than six stories are normally severely restricted by building codes from being wood framed....

Wood and Other Materials Used to Construct Nonresidential Buildings in the United States 2011 Executive Summary

Treesearch

David B. McKeever

2013-01-01

The construction of low-rise nonresidential buildings is an important market for lumber, engineered wood products, and structural and nonstructural wood panels in the United States. This report examines low-rise nonresidential buildings of six or fewer stories. Those with more than six stories are normally severely restricted by building codes from being wood framed....

Integrated and holistic suitability assessment of recycling options for masonry rubble

NASA Astrophysics Data System (ADS)

Herbst, T.; Rübner, K.; Meng, B.

2012-04-01

Our industrial society depends on continuous mining and consumption of raw materials and energy. Besides, the building sector causes one of the largest material streams in Germany. On the one hand, the building sector is connected with a high need in material and energetic resources as well as financial expenditures. On the other hand, nearly 50 % of the volume of waste arises from the building industry. During the last years, the limitation of natural resources, increasing negative environmental consequences as well as rising prices and shortages of dump space have led to a change in thinking in the building and waste industry to a closed substance cycle waste management. In consideration of the production figures of the main kinds of masonry units (clay bricks, sand-lime bricks, autoclaved aerated concrete brick, concrete blocks), a not unimportant quantity of masonry rubble (including gypsum plaster boards, renders, mortars and mineral insulating materials) of more than 20 million tons per year is generated in the medium term. With regard to a sustainable closed substance cycle waste management, these rest masses have to be recycled if possible. Processed aggregates made from masonry rubble can be recycled in the production of new masonry units under certain conditions. Even carefully deconstructed masonry units can once more re-used as masonry units, particularly in the area of the preservation of monuments and historical buildings. In addition, masonry rubble in different processing qualities is applied in earth and road construction, horticulture and scenery construction as well as concrete production. The choice of the most suitable recycling option causes technical, economical and ecological questions. At present, a methodology for a comprehensive suitability assessment with a passable scope of work does not exist. Basic structured and structuring information on the recycling of masonry rubble is absent up to now. This as well as the economic and technical constraints lead to a subordinated utilization on a rather low application level (downcycling). However, masonry rubble should also be recycled on a higher level (upcycling) in the future. For this purpose, an integrated and holistic but also practically oriented methodology for the suitability assessment of different recycling applications for masonry rubble is developed for a PhD currently. The suitability assessment includes the simultaneous evaluation of technical, economical and ecological aspects. Therefore, all recycling phases (demolition, processing, re-use) and the main kinds of masonry units (sorted or mixed) with their specific properties have to be considered.

Unit 5, nonfederal wall, 536538 Vine Street Building, & St. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Unit 5, non-federal wall, 536-538 Vine Street Building, & St. Vincent-Depaul store building-context - Johnstown Local Flood Protection Project, Beginning on Conemaugh River approx 3.8 miles downstream from confluence of Little Conemaugh & Stony Creek Rivers at Johnstown, Johnstown, Cambria County, PA

76 FR 39843 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-07

...: National Institute of Standards and Technology (NIST). Title: Usage of Elevators for Occupant Evacuation...- story buildings in the United States during fire emergencies. This research aims to summarize emergency... emergency procedures for multi-story buildings) from existing buildings in the United States, including...

Mandating better buildings: a global review of building codes and prospects for improvement in the United States

DOE PAGES

Sun, Xiaojing; Brown, Marilyn A.; Cox, Matt; ...

2015-03-11

This paper provides a global overview of the design, implementation, and evolution of building energy codes. Reflecting alternative policy goals, building energy codes differ significantly across the United States, the European Union, and China. This review uncovers numerous innovative practices including greenhouse gas emissions caps per square meter of building space, energy performance certificates with retrofit recommendations, and inclusion of renewable energy to achieve “nearly zero-energy buildings”. These innovations motivated an assessment of an aggressive commercial building code applied to all US states, requiring both new construction and buildings with major modifications to comply with the latest version of themore » ASHRAE 90.1 Standards. Using the National Energy Modeling System (NEMS), we estimate that by 2035, such building codes in the United States could reduce energy for space heating, cooling, water heating and lighting in commercial buildings by 16%, 15%, 20% and 5%, respectively. Impacts on different fuels and building types, energy rates and bills as well as pollution emission reductions are also examined.« less

Control of dispatch dynamics for lowering the cost of distributed generation in the built environment

NASA Astrophysics Data System (ADS)

Flores, Robert Joseph

Distributed generation can provide many benefits over traditional central generation such as increased reliability and efficiency while reducing emissions. Despite these potential benefits, distributed generation is generally not purchased unless it reduces energy costs. Economic dispatch strategies can be designed such that distributed generation technologies reduce overall facility energy costs. In this thesis, a microturbine generator is dispatched using different economic control strategies, reducing the cost of energy to the facility. Several industrial and commercial facilities are simulated using acquired electrical, heating, and cooling load data. Industrial and commercial utility rate structures are modeled after Southern California Edison and Southern California Gas Company tariffs and used to find energy costs for the simulated buildings and corresponding microturbine dispatch. Using these control strategies, building models, and utility rate models, a parametric study examining various generator characteristics is performed. An economic assessment of the distributed generation is then performed for both the microturbine generator and parametric study. Without the ability to export electricity to the grid, the economic value of distributed generation is limited to reducing the individual costs that make up the cost of energy for a building. Any economic dispatch strategy must be built to reduce these individual costs. While the ability of distributed generation to reduce cost depends of factors such as electrical efficiency and operations and maintenance cost, the building energy demand being serviced has a strong effect on cost reduction. Buildings with low load factors can accept distributed generation with higher operating costs (low electrical efficiency and/or high operations and maintenance cost) due to the value of demand reduction. As load factor increases, lower operating cost generators are desired due to a larger portion of the building load being met in an effort to reduce demand. In addition, buildings with large thermal demand have access to the least expensive natural gas, lowering the cost of operating distributed generation. Recovery of exhaust heat from DG reduces cost only if the buildings thermal demand coincides with the electrical demand. Capacity limits exist where annual savings from operation of distributed generation decrease if further generation is installed. For low operating cost generators, the approximate limit is the average building load. This limit decreases as operating costs increase. In addition, a high capital cost of distributed generation can be accepted if generator operating costs are low. As generator operating costs increase, capital cost must decrease if a positive economic performance is desired.

Lesson Learned from Technical and Economic Performance Assessment and Benefit Evaluation of CHP-FCS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Makhmalbaf, Atefe; Brooks, Kriston P.; Srivastava, Viraj

2014-08-22

Recent efforts and interest in combined heat and power (CHP) have increased with the momentum provided by the federal government support for penetration of CHP systems. Combined heat and power fuel cell systems (CHP-FCSs) provide consistent electrical power and utilize the heat normally wasted in power generation for useful heating or cooling with lower emissions compared to alternative sources. A recent study investigated the utilization of CHP-FCSs in the range of 5 to 50KWe in various commercial building types and geographic locations. Electricity, heating, and water heating demands were obtained from simulation of the U.S. Department of Energy (DOE) commercialmore » reference building models for various building types. Utility rates, cost of equipment, and system efficiency were used to examine economic payback in different scenarios. As a new technology in the early stages of adoption, CHP-FCSs are more expensive than alternative technologies, and the high capital cost of the CHP-FCSs results in a longer payback period than is typically acceptable for all but early-adopter market segments. However, the installation of these units as on-site power generators also provide several other benefits that make them attractive to building owners and operators. The business case for CHP-FCSs can be made more financially attractive through the provision of government incentives and when installed to support strategic infrastructure, such as military installations or data centers. The results presented in this paper intend to provide policy makers with information to define more customized incentives and tax credits based on a sample of building types and geographic locations in order to attract more business investment in this new technology.« less

Heat-pump-centered integrated community energy systems: Systems development, Consolidated Natural Gas Service Company

NASA Astrophysics Data System (ADS)

Baker, N. R.; Donakowski, T. D.; Foster, R. B.; Sala, D. L.; Tison, R. R.; Whaley, T. P.; Yudow, B. D.; Swenson, P. F.

1980-01-01

The heat actuated heat pump centered integrated community energy system (HAHP-ICES) is described. The system utilizes a gas fired, engine-driven, heat pump and commercial buildings, and offers several advantages over the more conventional equipment it is intended to supplant. The general nonsite specific application assumes a hypothetical community of one 59,000 cu ft office building and five 24 unit, low rise apartment buildings located in a region with a climate similar to Chicago. Various sensitivity analyses are performed and through which the performance characteristics of the HAHP are explored. The results provided the selection criteria for the site specific application of the HAHP-ICES concept to a real world community. The site-specific community consists of: 42 town houses; five 120 unit, low rise apartment buildings; five 104 unit high rise apartment buildings; one 124,000 cu ft office building; and a single 135,000 cu ft retail building.

24 CFR 200.940 - Supplementary specific requirements under the HUD building product standards and certification...

Code of Federal Regulations, 2011 CFR

2011-04-01

... under the HUD building product standards and certification program for sealed insulating glass units... sealed insulating glass units. (a) Applicable standards. (1) All sealed insulating glass units shall be... standard: ASTM E-774-92 Standard Specification for Sealed Insulating Glass Units. (2) This standard has...

24 CFR 200.940 - Supplementary specific requirements under the HUD building product standards and certification...

Code of Federal Regulations, 2010 CFR

2010-04-01

... under the HUD building product standards and certification program for sealed insulating glass units... sealed insulating glass units. (a) Applicable standards. (1) All sealed insulating glass units shall be... standard: ASTM E-774-92 Standard Specification for Sealed Insulating Glass Units. (2) This standard has...

Agricultural Structures. Volume I. Instructor's Guide. Volume 13, Number 1.

ERIC Educational Resources Information Center

Linhardt, Richard E.; Burhoe, Steve

This document is a curriculum unit in agricultural structures designed to expand the curriculum materials available in vocational agriculture in Missouri. The guide consists of three units on constructing farm buildings, planning farm water systems, and building fences. Each unit contains 10-15 lessons on various aspects of the unit's topic. Each…

Tsunami Simulators in Physical Modelling - Concept to Practical Solutions

NASA Astrophysics Data System (ADS)

Chandler, Ian; Allsop, William; Robinson, David; Rossetto, Tiziana; McGovern, David; Todd, David

2017-04-01

Whilst many researchers have conducted simple 'tsunami impact' studies, few engineering tools are available to assess the onshore impacts of tsunami, with no agreed methods available to predict loadings on coastal defences, buildings or related infrastructure. Most previous impact studies have relied upon unrealistic waveforms (solitary or dam-break waves and bores) rather than full-duration tsunami waves, or have used simplified models of nearshore and over-land flows. Over the last 10+ years, pneumatic Tsunami Simulators for the hydraulic laboratory have been developed into an exciting and versatile technology, allowing the forces of real-world tsunami to be reproduced and measured in a laboratory environment for the first time. These devices have been used to model generic elevated and N-wave tsunamis up to and over simple shorelines, and at example coastal defences and infrastructure. They have also reproduced full-duration tsunamis including Mercator 2004 and Tohoku 2011, both at 1:50 scale. Engineering scale models of these tsunamis have measured wave run-up on simple slopes, forces on idealised sea defences, pressures / forces on buildings, and scour at idealised buildings. This presentation will describe how these Tsunami Simulators work, demonstrate how they have generated tsunami waves longer than the facilities within which they operate, and will present research results from three generations of Tsunami Simulators. Highlights of direct importance to natural hazard modellers and coastal engineers include measurements of wave run-up levels, forces on single and multiple buildings and comparison with previous theoretical predictions. Multiple buildings have two malign effects. The density of buildings to flow area (blockage ratio) increases water depths and flow velocities in the 'streets'. But the increased building densities themselves also increase the cost of flow per unit area (both personal and monetary). The most recent study with the Tsunami Simulators therefore focussed on the influence of multiple buildings (up to 4 rows) which showed (for instance) that the greatest forces can act on the landward (not seaward) rows of buildings. Studies in the 70m long, 4m wide main channel of the Fast Flow Facility on tsunami defence structures have also measured forces on buildings in the lee of a failed defence wall and tsunami induced scour. Supporting presentations at this conference: McGovern et al on tsunami induced scour at coastal structures and Foster et al on building loads.

Methyl chloride via oxyhydrochlorination of methane: A building block for chemicals and fuels from natural gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benson, R.L.; Brown, S.S.D.; Ferguson, S.P.

1995-12-31

The objectives of this program are to (a) develop a process for converting natural gas to methyl chloride via an oxyhydrochlorination route using highly selective, stable catalysts in a fixed-bed, (b) design a reactor capable of removing the large amount of heat generated in the process so as to control the reaction, (c) develop a recovery system capable of removing the methyl chloride from the product stream and (d) determine the economics and commercial viability of the process. The general approach has been as follows: (a) design and build a laboratory scale reactor, (b) define and synthesize suitable OHC catalystsmore » for evaluation, (c) select first generation OHC catalyst for Process Development Unit (PDU) trials, (d) design, construct and startup PDU, (e) evaluate packed bed reactor design, (f) optimize process, in particular, product recovery operations, (g) determine economics of process, (h) complete preliminary engineering design for Phase II and (i) make scale-up decision and formulate business plan for Phase II. Conclusions regarding process development and catalyst development are presented.« less

Energy Consumption Evaluation of United States Navy Leed Certified Building For Fiscal Year 2009

DTIC Science & Technology

2010-01-01

administration functions, classroom training, laboratory functions, personnel detention, and a fully functioning dog kennel on the exterior of the...Leadership in Energy and Environmental Design (LEED) Silver certified by the United States Green Building Council (USGBC). The goal of this effort is in...and Environmental Design (LEED) Silver certified by the United States Green Building Council (USGBC). The goal of this effort is in compliance with

Generations of interdisciplinarity in bioinformatics

PubMed Central

Bartlett, Andrew; Lewis, Jamie; Williams, Matthew L.

2016-01-01

Bioinformatics, a specialism propelled into relevance by the Human Genome Project and the subsequent -omic turn in the life science, is an interdisciplinary field of research. Qualitative work on the disciplinary identities of bioinformaticians has revealed the tensions involved in work in this “borderland.” As part of our ongoing work on the emergence of bioinformatics, between 2010 and 2011, we conducted a survey of United Kingdom-based academic bioinformaticians. Building on insights drawn from our fieldwork over the past decade, we present results from this survey relevant to a discussion of disciplinary generation and stabilization. Not only is there evidence of an attitudinal divide between the different disciplinary cultures that make up bioinformatics, but there are distinctions between the forerunners, founders and the followers; as inter/disciplines mature, they face challenges that are both inter-disciplinary and inter-generational in nature. PMID:27453689

Extended Operation of Stirling Convertors at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Oriti, Salvatore, M.

2012-01-01

NASA Glenn Research Center (GRC) has been supporting development of free-piston Stirling conversion technology for spaceflight electrical power generation since 1999. GRC has also been supporting the development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG project is providing life, reliability, and performance data for the Advanced Stirling Convertor (ASC). The Thermal Energy Conversion branch at GRC is conducting extended operation of several free-piston Stirling convertors. The goal of this effort is to generate long-term performance data (tens of thousands of hours) on multiple units to build a life and reliability database. Currently, GRC is operating 18 convertors. This hardware set includes Technology Demonstration Convertors (TDCs) from Infinia Corporation, of which one pair (TDCs #13 and #14) has accumulated over 60,000 hr (6.8 years) of operation. Also under test are various Sunpower, Inc. convertors that were fabricated during the ASC development activity, including ASC-0, ASC-E (including those in the ASRG engineering unit), and ASC-E2. The ASC-E2s also completed, or are in progress of completing workmanship vibration testing, performance mapping, and extended operation. Two ASC-E2 units will also be used for durability testing, during which components will be stressed to levels above nominal mission usage. Extended operation data analyses from these tests are covered in this paper.

NASA's Next Generation Space Geodesy Program

NASA Technical Reports Server (NTRS)

Pearlman, M. R.; Frey, H. V.; Gross, R. S.; Lemoine, F. G.; Long, J. L.; Ma, C.; McGarry J. F.; Merkowitz, S. M.; Noll, C. E.; Pavilis, E. C.;

NASA's Next Generation Space Geodesy Program

NASA Technical Reports Server (NTRS)

Merkowitz, S. M.; Desai, S. D.; Gross, R. S.; Hillard, L. M.; Lemoine, F. G.; Long, J. L.; Ma, C.; McGarry, J. F.; Murphy, D.; Noll, C. E.;

Masonry. Teacher's Guide. Building Maintenance Units of Instruction.

ERIC Educational Resources Information Center

Barnes, Bill

This teaching guide on masonry building maintenance, one in a series of six publications designed for building maintenance instructors in Texas, is designed to give students an understanding of masonry construction. Introductory material provides teachers with information on use of the units of instruction and personalization and localization of…

Building Technologies Office FY 2017 Budget At-A-Glance

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2016-03-01

Buildings and homes use more than 73% of the electrical energy consumed in the United States. They also consume 40% of the nation’s total energy, with an annual energy bill of $430 billion. These energy bills can be cost effectively reduced by 20%–50% or more through various energy-efficient technologies and techniques. The Building Technologies Office (BTO) will continue to develop and demonstrate advanced building efficiency technologies and practices to make buildings in the United States more efficient, affordable, and comfortable.

Passive Residential Houses with the Accumulation Properties of Ground as a Heat Storage Medium

NASA Astrophysics Data System (ADS)

Ochab, Piotr; Kokoszka, Wanda; Kogut, Janusz; Skrzypczak, Izabela; Szyszka, Jerzy; Starakiewicz, Aleksander

2017-12-01

Solar radiation is the primary source of life energy on Earth. The irradiance of the upper atmosphere is about 1360 W/m2, and it is estimated that about 1000 W/m2 reaches the ground. Long-term storage of heat energy is related to the use of a suitable thermal energy carrier. It may be either artificial or natural water tank, or artificial gravel-water tank, or aquifer or soil. It is justified to store the generated energy in large heating systems due to the nature of solar thermal energy. Typically, in such a solution storage space is a large solar collector farm. The reason for this is the proportionally small unit profits, which only in the case of large number of units provides sufficient energy that can be accumulated. It should be noted that Poland, a country located in a temperate and less harsh climate such as Scandinavia and Canada, has a relatively high potential for solar revenue. In the last decade, it has caused mainly small and individual heating installations. However, much of the municipal and industrial economy continues to rely on energy from non-renewable resources. This is due not only to the lack of a high-efficiency alternative to non-renewable energy resources, but also to the thermal state of buildings throughout the country, where old buildings require thermomodernization. This has the effect of both polluting the environment and the occurrence of smog, as well as pollutants in water and soil. This directly affects the occurrence of civilization diseases and other societal health problems. Therefore, the surplus of thermal clean energy that occurs during the spring and summer period should not only be used on a regular basis, but also stored for later winter use. The paper presents the concept of housing estate, which consists of 32 twin housing units. The solid character of buildings consistently refers to passive construction, and the materials meet the requirements for the passive buildings.

Program THEK energy production units of average power and using thermal conversion of solar radiation

NASA Technical Reports Server (NTRS)

1978-01-01

General studies undertaken by the C.N.R.S. in the field of solar power plants have generated the problem of building energy production units in the medium range of electrical power, in the order of 100 kW. Among the possible solutions, the principle of the use of distributed heliothermal converters has been selected as being, with the current status of things, the most advantageous solution. This principle consists of obtaining the conversion of concentrated radiation into heat by using a series of heliothermal conversion modules scattered over the ground; the produced heat is collected by a heat-carrying fluid circulating inside a thermal loop leading to a device for both regulation and storage.

NREL Offshore Balance-of-System Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maness, Michael; Maples, Benjamin; Smith, Aaron

The U.S. Department of Energy (DOE) has investigated the potential for 20% of nationwide electricity demand to be generated from wind by 2030 and, more recently, 35% by 2050. Achieving this level of wind power generation may require the development and deployment of offshore wind technologies. DOE (2008) has indicated that reaching these 2030 and 2050 scenarios could result in approximately 10% and 20%, respectively, of wind energy generation to come from offshore resources. By the end of 2013, 6.5 gigawatts of offshore wind were installed globally. The first U.S. project, the Block Island Wind Farm off the coast ofmore » Rhode Island, has recently begun operations. One of the major reasons that offshore wind development in the United States is lagging behind global trends is the high capital expenditures required. An understanding of the costs and associated drivers of building a commercial-scale offshore wind plant in the United States will inform future research and help U.S. investors feel more confident in offshore wind development. In an effort to explain these costs, the National Renewable Energy Laboratory has developed the Offshore Balance-of-System model.« less

23. BUILDING NO. 22L, SHEET NO. 3. United Engineering Company ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. BUILDING NO. 22L, SHEET NO. 3. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities. Plans, section, & detail. Alben Froberg, Architect, 3454 Harlan Street, Oakland, California. Sheet no. 3. Plan no. 10,525. Various scales. March 1, 1943, last revised 3/15/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Engineering Building, 2900 Main Street, Alameda, Alameda County, CA

22. BUILDING NO. 22L, SHEET NO. 2. United Engineering Company ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. BUILDING NO. 22L, SHEET NO. 2. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities. Plans, section, & detail. Alben Froberg, Architect, 3454 Harlan Street, Oakland, California. Sheet no. 2. Plan no. 10,525. Various scales. March 1, 1942, last revised 3/15/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Engineering Building, 2900 Main Street, Alameda, Alameda County, CA

Gaussian curvature analysis allows for automatic block placement in multi-block hexahedral meshing.

PubMed

Ramme, Austin J; Shivanna, Kiran H; Magnotta, Vincent A; Grosland, Nicole M

2011-10-01

Musculoskeletal finite element analysis (FEA) has been essential to research in orthopaedic biomechanics. The generation of a volumetric mesh is often the most challenging step in a FEA. Hexahedral meshing tools that are based on a multi-block approach rely on the manual placement of building blocks for their mesh generation scheme. We hypothesise that Gaussian curvature analysis could be used to automatically develop a building block structure for multi-block hexahedral mesh generation. The Automated Building Block Algorithm incorporates principles from differential geometry, combinatorics, statistical analysis and computer science to automatically generate a building block structure to represent a given surface without prior information. We have applied this algorithm to 29 bones of varying geometries and successfully generated a usable mesh in all cases. This work represents a significant advancement in automating the definition of building blocks.

Final Status Survey Report for Corrective Action Unit 117 - Pluto Disassembly Facility, Building 2201, Nevada National Security Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeremy Gwin and Douglas Frenette

This document contains the process knowledge, radiological data and subsequent statistical methodology and analysis to support approval for the radiological release of Corrective Action Unit (CAU) 117 – Pluto Disassembly Facility, Building 2201 located in Area 26 of the Nevada National Security Site (NNSS). Preparations for release of the building began in 2009 and followed the methodology described in the Multi-Agency Radiation Survey and Site Investigation Manual (MARSSIM). MARSSIM is the DOE approved process for release of Real Property (buildings and landmasses) to a set of established criteria or authorized limits. The pre-approved authorized limits for surface contamination values andmore » corresponding assumptions were established by DOE O 5400.5. The release criteria coincide with the acceptance criteria of the U10C landfill permit. The U10C landfill is the proposed location to dispose of the radiologically non-impacted, or “clean,” building rubble following demolition. However, other disposition options that include the building and/or waste remaining at the NNSS may be considered providing that the same release limits apply. The Final Status Survey was designed following MARSSIM guidance by reviewing historical documentation and radiological survey data. Following this review a formal radiological characterization survey was performed in two phases. The characterization revealed multiple areas of residual radioactivity above the release criteria. These locations were remediated (decontaminated) and then the surface activity was verified to be less than the release criteria. Once remediation efforts had been successfully completed, a Final Status Survey Plan (10-015, “Final Status Survey Plan for Corrective Action Unit 117 – Pluto Disassembly Facility, Building 2201”) was developed and implemented to complete the final step in the MARSSIM process, the Final Status Survey. The Final Status Survey Plan consisted of categorizing each individual room into one of three categories: Class 1, Class 2 or Class 3 (a fourth category is a “Non-Impacted Class” which in the case of Building 2201 only pertained to exterior surfaces of the building.) The majority of the rooms were determined to fall in the less restrictive Class 3 category, however, Rooms 102, 104, 106, and 107 were identified as containing Class 1 and 2 areas. Building 2201 was divided into “survey units” and surveyed following the requirements of the Final Status Survey Plan for each particular class. As each survey unit was completed and documented, the survey results were evaluated. Each sample (static measurement) with units of counts per minute (cpm) was corrected for the appropriate background and converted to a value with units of dpm/100 cm2. With a surface contamination value in the appropriate units, it was compared to the surface contamination limits, or in this case the derived concentration guideline level (DCGLw). The appropriate statistical test (sign test) was then performed. If the survey unit was statistically determined to be below the DCGLw, then the survey unit passed and the null hypothesis (that the survey unit is above limits) was rejected. If the survey unit was equal to or below the critical value in the sign test, the null hypothesis was not rejected. This process was performed for all survey units within Building 2201. A total of thirty-three “Class 1,” four “Class 2,” and one “Class 3” survey units were developed, surveyed, and evaluated. All survey units successfully passed the statistical test. Building 2201 meets the release criteria commensurate with the Waste Acceptance Criteria (for radiological purposes) of the U10C landfill permit residing within NNSS boundaries. Based on the thorough statistical sampling and scanning of the building’s interior, Building 2201 may be considered radiologically “clean,” or free of contamination.« less

Effective Light Directed Assembly of Building Blocks with Microscale Control.

PubMed

Dinh, Ngoc-Duy; Luo, Rongcong; Christine, Maria Tankeh Asuncion; Lin, Weikang Nicholas; Shih, Wei-Chuan; Goh, James Cho-Hong; Chen, Chia-Hung

2017-06-01

Light-directed forces have been widely used to pattern micro/nanoscale objects with precise control, forming functional assemblies. However, a substantial laser intensity is required to generate sufficient optical gradient forces to move a small object in a certain direction, causing limited throughput for applications. A high-throughput light-directed assembly is demonstrated as a printing technology by introducing gold nanorods to induce thermal convection flows that move microparticles (diameter = 40 µm to several hundreds of micrometers) to specific light-guided locations, forming desired patterns. With the advantage of effective light-directed assembly, the microfluidic-fabricated monodispersed biocompatible microparticles are used as building blocks to construct a structured assembly (≈10 cm scale) in ≈2 min. The control with microscale precision is approached by changing the size of the laser light spot. After crosslinking assembly of building blocks, a novel soft material with wanted pattern is approached. To demonstrate its application, the mesenchymal stem-cell-seeded hydrogel microparticles are prepared as functional building blocks to construct scaffold-free tissues with desired structures. This light-directed fabrication method can be applied to integrate different building units, enabling the bottom-up formation of materials with precise control over their internal structure for bioprinting, tissue engineering, and advanced manufacturing. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structurally integrated steel solar collector

DOEpatents

Moore, Stanley W.

1977-03-08

Herein is disclosed a flat plate solar heat collector unit. The solar collector is integrated as a structural unit so that the collector also functions as the building roof. The functions of efficient heat collection, liquid coolant flow passages, roof structural support and building insulation are combined into one unit.

Structurally integrated steel solar collector

DOEpatents

Moore, S.W.

1975-06-03

Herein is disclosed a flate plate solar heat collector unit. The solar collector is integrated as a structural unit so that the collector also functions as the building roof. The functions of efficient heat collection, liquid coolant flow passages, roof structural support, and building insulation are combined into one unit.

Building Our Children's Future: An Interdisciplinary Curriculum for Grades K-12.

ERIC Educational Resources Information Center

Mumma, Tracy; Gant, Shaun; Stone, Laura Armstrong; Harnish, Chris; Fowle, Abigail

This interdisciplinary curriculum provides students with the opportunity to learn about the connection between natural resources and buildings while practicing skills in language arts, math, science, social studies, and visual arts. The learning activities are divided by topic into 15 Building Blocks (units). These units cover such topics as…

To designate the Federal building and United States courthouse located at 300 Fayetteville Street in Raleigh, North Carolina, as the "Jesse Helms Federal Building and United States Courthouse".

THOMAS, 112th Congress

Rep. Ellmers, Renee L. [R-NC-2

2012-11-27

House - 11/28/2012 Referred to the Subcommittee on Economic Development, Public Buildings and Emergency Management. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

To designate the Federal Building and United States Courthouse located at 1125 Chapline Street in Wheeling, West Virginia, as the "Frederick P. Stamp, Jr. Federal Building and United States Courthouse".

THOMAS, 113th Congress

Rep. McKinley, David B. [R-WV-1

2013-02-12

House - 02/13/2013 Referred to the Subcommittee on Economic Development, Public Buildings and Emergency Management. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

Combined experimental and numerical evaluation of a prototype nano-PCM enhanced wallboard

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biswas, Kaushik; LuPh.D., Jue; Soroushian, Parviz

2014-01-01

In the United States, forty-eight (48) percent of the residential end-use energy consumption is spent on space heating and air conditioning. Reducing envelope-generated heating and cooling loads through application of phase change material (PCM)-enhanced building envelopes can facilitate maximizing the energy efficiency of buildings. Combined experimental testing and numerical modeling of PCM-enhanced envelope components are two important aspects of the evaluation of their energy benefits. An innovative phase change material (nano-PCM) was developed with PCM encapsulated with expanded graphite (interconnected) nanosheets, which is highly conductive for enhanced thermal storage and energy distribution, and is shape-stable for convenient incorporation into lightweightmore » building components. A wall with cellulose cavity insulation and prototype PCM-enhanced interior wallboards was built and tested in a natural exposure test (NET) facility in a hot-humid climate location. The test wall contained PCM wallboards and regular gypsum wallboard, for a side-by-side annual comparison study. Further, numerical modeling of the walls containing the nano-PCM wallboard was performed to determine its actual impact on wall-generated heating and cooling loads. The model was first validated using experimental data, and then used for annual simulations using Typical Meteorological Year (TMY3) weather data. This article presents the measured performance and numerical analysis evaluating the energy-saving potential of the nano-PCM-enhanced wallboard.« less

Toward a Nation-Building Operating Concept

DTIC Science & Technology

2010-04-13

of United Nations intervention in Timor, argues that an interim protectorate is useful only if implemented by a multi -national coalition. However...to a franchise agreement or venture capital investment. The United States provides capital and expertise to indigenous group predicated on agreed...Toward a Nation-Building Operating Concept by Colonel John DeJarnette United States Army School of Advanced Military Studies United States

Successfully Demonstrating an Integrated Roofing and BIPV Solution for an Historic Building Renovation at the United States Air Force Academy

DTIC Science & Technology

2011-05-01

Solution for an Historic Building Renovation at the United States Air Force Academy • Abstract Number: 12623 Vandenberg Hall • Thin Film Solar Array • Direct...Phase 1 • Total installed production capacity: 212.320 KW DC • Panels type and quantity: • Unisolar Thin Film Amorphous Silicon Panels • 1210 – Power...Successfully Demonstrating an Integrated Roofing and BIPV Solution for an Historic Building Renovation at the United States Air Force Academy

Stability and Degradation Mechanisms of Metal-Organic Frameworks Containing the Zr6O4(OH)4 Secondary Building Unit

DTIC Science & Technology

2013-03-18

0188 3. DATES COVERED (From - To) - UU UU UU UU Approved for public release; distribution is unlimited. Stability and degradation mechanisms of metal ...Stability and degradation mechanisms of metal –organic frameworks containing the Zr6O4(OH)4 secondary building unit Report Title See publication. 3...Stability and degradation mechanisms of metal –organic frameworks containing the Zr6O4(OH)4 secondary building unit Approved for public release; distribution

Community United Methodist Church passive solar classroom addition: comparison of predicted and actual energy use

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, W.H.; Peckham, N.

1984-01-01

The Community United Methodist Church of Columbia, Missouri, has recently built a passive solar addition. This building was partially funded by the Department of Energy Passive Solar Commercial Building Demonstration Program (1) and by a grant from the Board of Global Ministries of the United Methodist Church. As part of the design phase, the PASOLE computer code was used to model the thermal characteristics of the building. The building was subsequently completed in September 1981, and one and one-half years of end use energy data has been collected as of March 1983. This paper presents (1) a description of themore » new building and the computer model used to analyze it, (2) a comparison of predicted and actual energy use, (3) a comparison between the new, solar building and conventional portions of the church complex and (4) summarizes other operational experiences.« less

Fungal colonization of fiberglass insulation in the air distribution system of a multi-story office building: VOC production and possible relationship to a sick building syndrome.

PubMed

Ahearn, D G; Crow, S A; Simmons, R B; Price, D L; Noble, J A; Mishra, S K; Pierson, D L

1996-05-01

Complaints characteristic of those for sick building syndrome prompted mycological investigations of a modern multi-story office building on the Gulf coast in the Southeastern United States (Houston-Galveston area). The air handling units and fiberglass duct liner of the heating, ventilating and air conditioning system of the building, without a history of catastrophic or chronic water damage, demonstrated extensive colonization with Penicillium spp and Cladosporium herbarum. Although dense fungal growth was observed on surfaces within the heating-cooling system, most air samples yielded fewer than 200 CFU m-3. Several volatile compounds found in the building air were released also from colonized fiberglass. Removal of colonized insulation from the floor receiving the majority of complaints of mouldy air and continuous operation of the units supplying this floor resulted in a reduction in the number of complaints.

Fungal colonization of fiberglass insulation in the air distribution system of a multi-story office building: VOC production and possible relationship to a sick building syndrome

NASA Technical Reports Server (NTRS)

Ahearn, D. G.; Crow, S. A.; Simmons, R. B.; Price, D. L.; Noble, J. A.; Mishra, S. K.; Pierson, D. L.

1996-01-01

Complaints characteristic of those for sick building syndrome prompted mycological investigations of a modern multi-story office building on the Gulf coast in the Southeastern United States (Houston-Galveston area). The air handling units and fiberglass duct liner of the heating, ventilating and air conditioning system of the building, without a history of catastrophic or chronic water damage, demonstrated extensive colonization with Penicillium spp and Cladosporium herbarum. Although dense fungal growth was observed on surfaces within the heating-cooling system, most air samples yielded fewer than 200 CFU m-3. Several volatile compounds found in the building air were released also from colonized fiberglass. Removal of colonized insulation from the floor receiving the majority of complaints of mouldy air and continuous operation of the units supplying this floor resulted in a reduction in the number of complaints.

Development of Automated Procedures to Generate Reference Building Models for ASHRAE Standard 90.1 and India’s Building Energy Code and Implementation in OpenStudio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, Andrew; Haves, Philip; Jegi, Subhash

This paper describes a software system for automatically generating a reference (baseline) building energy model from the proposed (as-designed) building energy model. This system is built using the OpenStudio Software Development Kit (SDK) and is designed to operate on building energy models in the OpenStudio file format.

Responses of two tall buildings in Tokyo, Japan, before, during, and after the M9.0 Tohoku earthquake of 11 March 2011

USGS Publications Warehouse

Çelebi, Mehmet; Hisada, Yoshiuaki; Omrani, Roshanak; Ghahari, S. Farid; Taciroglu, Ertugrul

2016-01-01

The 11 March 2011 M 9.0 Tohoku earthquake generated significant long duration shaking that propagated hundreds of kilometers from the epicenter and affected urban areas throughout much of Honshu. Recorded responses of tall buildings at several hundred km from the epicenter of the main shock and other events show tall buildings were affected by long-period motions of events at distant sources. This study presents behavioral aspects of 29-story and 30-story neighboring buildings in the Shinjuku area of Tokyo, Japan, as inferred from records retrieved from a sparse array of accelerometers deployed in the superstructures, at ground and 100 m below the ground level over a time interval covering before, during, and after the main shock. Such long-period effects are common in several regions of Japan as well as in the United States and in other seismically active countries. Permanent shifts in fundamental frequencies are observed. Drift ratios indicate possible structural nonlinear behavior occurred during the main shock. The need to consider risks to built environments from distant sources, including those in neighboring countries, is emphasized.

Interdisciplinary design study of a high-rise integrated roof wind energy system

NASA Astrophysics Data System (ADS)

Dekker, R. W. A.; Ferraro, R. M.; Suma, A. B.; Moonen, S. P. G.

2012-10-01

Today's market in micro-wind turbines is in constant development introducing more efficient solutions for the future. Besides the private use of tower supported turbines, opportunities to integrate wind turbines in the built environment arise. The Integrated Roof Wind Energy System (IRWES) presented in this work is a modular roof structure integrated on top of existing or new buildings. IRWES is build up by an axial array of skewed shaped funnels used for both wind inlet and outlet. This inventive use of shape and geometry leads to a converging air capturing inlet to create high wind mass flow and velocity toward a Vertical Axis Wind Turbine (VAWT) in the center-top of the roof unit for the generation of a relatively high amount of energy. The scope of this research aims to make an optimized structural design of IRWES to be placed on top of the Vertigo building in Eindhoven; analysis of the structural performance; and impact to the existing structure by means of Finite Element Modeling (FEM). Results show that the obvious impact of wind pressure to the structural design is easily supported in different configurations of fairly simple lightweight structures. In particular, the weight addition to existing buildings remains minimal.

Three-dimensional aromatic networks.

PubMed

Toyota, Shinji; Iwanaga, Tetsuo

2014-01-01

Three-dimensional (3D) networks consisting of aromatic units and linkers are reviewed from various aspects. To understand principles for the construction of such compounds, we generalize the roles of building units, the synthetic approaches, and the classification of networks. As fundamental compounds, cyclophanes with large aromatic units and aromatic macrocycles with linear acetylene linkers are highlighted in terms of transannular interactions between aromatic units, conformational preference, and resolution of chiral derivatives. Polycyclic cage compounds are constructed from building units by linkages via covalent bonds, metal-coordination bonds, or hydrogen bonds. Large cage networks often include a wide range of guest species in their cavity to afford novel inclusion compounds. Topological isomers consisting of two or more macrocycles are formed by cyclization of preorganized species. Some complicated topological networks are constructed by self-assembly of simple building units.

The Seasonal Predictability of Extreme Wind Events in the Southwest United States

NASA Astrophysics Data System (ADS)

Seastrand, Simona Renee

Extreme wind events are a common phenomenon in the Southwest United States. Entities such as the United States Air Force (USAF) find the Southwest appealing for many reasons, primarily for the an expansive, unpopulated, and electronically unpolluted space for large-scale training and testing. However, wind events can cause hazards for the USAF including: surface wind gusts can impact the take-off and landing of all aircraft, can tip the airframes of large wing-surface aircraft during the performance of maneuvers close to the ground, and can even impact weapons systems. This dissertation is comprised of three sections intended to further our knowledge and understanding of wind events in the Southwest. The first section builds a climatology of wind events for seven locations in the Southwest during the twelve 3-month seasons of the year. The first section further examines the wind events in relation to terrain and the large-scale flow of the atmosphere. The second section builds upon the first by taking the wind events and generating mid-level composites for each of the twelve 3-month seasons. In the third section, teleconnections identified as consistent with the large-scale circulation in the second paper were used as predictor variables to build a Poisson regression model for each of the twelve 3-month seasons. The purpose of this research is to increase our understanding of the climatology of extreme wind events, increase our understanding of how the large-scale circulation influences extreme wind events, and create a model to enhance predictability of extreme wind events in the Southwest. Knowledge from this paper will help protect personnel and property associated with not only the USAF, but all those in the Southwest.

Effect of outside air ventilation rate on VOC concentrations and emissions in a call center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hodgson, A.T.; Faulkner, D.; Sullivan, D.P.

2002-01-01

A study of the relationship between outside air ventilation rate and concentrations of VOCs generated indoors was conducted in a call center. Ventilation rates were manipulated in the building's four air handling units (AHUs). Concentrations of VOCs in the AHU returns were measured on 7 days during a 13-week period. Indoor minus outdoor concentrations and emission factors were calculated. The emission factor data was subjected to principal component analysis to identify groups of co-varying compounds based on source type. One vector represented emissions of solvents from cleaning products. Another vector identified occupant sources. Direct relationships between ventilation rate and concentrationsmore » were not observed for most of the abundant VOCs. This result emphasizes the importance of source control measures for limiting VOC concentrations in buildings.« less

A rainwater harvesting system reliability model based on nonparametric stochastic rainfall generator

NASA Astrophysics Data System (ADS)

Basinger, Matt; Montalto, Franco; Lall, Upmanu

2010-10-01

SummaryThe reliability with which harvested rainwater can be used as a means of flushing toilets, irrigating gardens, and topping off air-conditioner serving multifamily residential buildings in New York City is assessed using a new rainwater harvesting (RWH) system reliability model. Although demonstrated with a specific case study, the model is portable because it is based on a nonparametric rainfall generation procedure utilizing a bootstrapped markov chain. Precipitation occurrence is simulated using transition probabilities derived for each day of the year based on the historical probability of wet and dry day state changes. Precipitation amounts are selected from a matrix of historical values within a moving 15 day window that is centered on the target day. RWH system reliability is determined for user-specified catchment area and tank volume ranges using precipitation ensembles generated using the described stochastic procedure. The reliability with which NYC backyard gardens can be irrigated and air conditioning units supplied with water harvested from local roofs exceeds 80% and 90%, respectively, for the entire range of catchment areas and tank volumes considered in the analysis. For RWH systems installed on the most commonly occurring rooftop catchment areas found in NYC (51-75 m 2), toilet flushing demand can be met with 7-40% reliability, with lower end of the range representing buildings with high flow toilets and no storage elements, and the upper end representing buildings that feature low flow fixtures and storage tanks of up to 5 m 3. When the reliability curves developed are used to size RWH systems to flush the low flow toilets of all multifamily buildings found a typical residential neighborhood in the Bronx, rooftop runoff inputs to the sewer system are reduced by approximately 28% over an average rainfall year, and potable water demand is reduced by approximately 53%.

Large Prefabricated Concrete Panels Collective Dwellings from the 1970s: Context and Improvements

NASA Astrophysics Data System (ADS)

Muntean, Daniel M.; Ungureanu, Viorel; Petran, Ioan; Georgescu, Mircea

2017-10-01

The period between 1960s and 1970s had a significant impact in Romania on the urban development of major cities. Because the vast expansion of the industry, the urban population has massively increased, due the large number of workers coming from the rural areas. This intense process has led to a shortage of homes on the housing market. In order to rapidly build new homes, standard residential project types were erected using large prefabricated concrete panels. By using repetitive patterns, such buildings were built in a short amount of time through the entire country. Nowadays, these buildings represent 1.8% of the built environment and accommodate more than half of a city’s population. Even though these units have reached only half their intended life span, they fail to satisfy present living standards and consume huge amounts of energy for heating, cooling, ventilation and lighting. Due to the fact that these building are based on standardised projects and were built in such a large scale, the creation of a system that brings them to current standards will not only benefit the building but also it will significantly improve the quality of life within. With the transition of the existing power grids to a “smart grid” such units can become micro power plants in future electricity networks thus contributing to micro-generation and energy storage. If one is to consider the EU 20-20-20 commitments, to find ideas for alternative and innovative strategies for further improving these building through locally adapted measures can be seen as one of the most addressed issues of today. This research offers a possible retrofitting scenario of these buildings towards a sustainable future. The building envelope is upgraded using a modular insulation system with integrated solar cells. Renewable energy systems for cooling and ventilation are integrated in order to provide flexibility of the indoor climate. Due to their small floor area, the space within the apartments is redesigned for a more efficient use of space and an improved natural lighting. Active core modules are placed on top of the unused attics and a solar panel array is introduced. Furthermore accessibility issues are addressed by facilitating access for disabled people and implementing an elevator system that currently these building do not have.

United States Air Force Summer Research Program -- 1993 Summer Research Program Final Reports. Volume 11. Arnold Engineering Development Center, Frank J. Seiler Research Laboratory, Wilford Hall Medical Center

DTIC Science & Technology

1993-01-01

external parameters such as airflow, temperature, pressure, etc, are measured. Turbine Engine testing generates massive volumes of data at very high...a form that describes the signal flow graph topology as well as specific parameters of the processing blocks in the diagram. On multiprocessor...provides an interface to the symbolic builder and control functions such that parameters may be set during the build operation that will affect the

P-Tether-Mediated, Iterative SN2'-Cuprate Alkylation Strategy to Skipped Polyol Stereotetrads: Utility of an Oxidative "Function Switch" with Phosphite-Borane Tethers.

PubMed

Markley, Jana L; Hanson, Paul R

2017-05-19

The development of a P-tether-mediated, iterative S N 2'-cuprate alkylation protocol for the formation of 1,3-skipped polyol stereotetrads is reported. This two-directional synthetic strategy builds molecular complexity from simple, readily prepared C 2 -symmetric dienediols and unites the chemistry of both temporary phosphite-borane tethers and temporary phosphate tethers-through an oxidative "function switch" of the P-tether itself-to generate intermediates that were previously inaccessible via either method alone.

Gate-to-Gate Life-Cycle Inventory on Hardwood Sawmills in the Northeastern Region of the United States

Treesearch

Richard D. Bergman

2007-01-01

Using sustainable building materials is gaining a significant presence in the United States therefore proving sustainability claims are becoming increasingly more important. Certifying wood products as green building materials is vital for the long-term productivity of the wood building industry and for forest management. This study examined hardwood lumber...

A crown-like heterometallic unit as the building block for a 3D In-Ge-S framework.

PubMed

Han, Xiaohui; Wang, Zhenqing; Xu, Jin; Liu, Dan; Wang, Cheng

2015-12-14

Supertetrahedral clusters are the most common building blocks in constructing Group 13/14/16 microporous metal chalcogenide materials while other types of clusters are yet scarcely explored. Herein, a new crown-like building unit [In3Ge3S16] has been obtained. The units assemble into a 3D framework [C6H14NO]4[In6Ge3S17]·1.5H2O (1) via a dual-connection mode and a SrSi2 (srs)-type topology could be achieved by treating each unit as a tri-connected node.

Water Reuse and Pathogen Tracking

EPA Science Inventory

Building product water. By designing our buildings to collect and treat water generated on-site, can be and reused for flushing our toilets and irrigating our landscaping. Several water sources are generated with-in a building including: rainwater, stormwater, graywater, blackwa...

Passivhaus: indoor comfort and energy dynamic analysis.

NASA Astrophysics Data System (ADS)

Guida, Antonella; Pagliuca, Antonello; Cardinale, Nicola; Rospi, Gianluca

2013-04-01

The research aims to verify the energy performance as well as the indoor comfort of an energy class A+ building, built so that the sum of the heat passive contributions of solar radiation, transmitted through the windows, and the heat generated inside the building, are adeguate to compensate for the envelope loss during the cold season. The building, located in Emilia Romagna (Italy), was built using a wooden structure, an envelope realized using a pinewood sandwich panels (transmittance U = 0.250 W/m2K) and, inside, a wool flax insulation layer and thermal window frame with low-emissivity glass (U = 0524 W/m2K). The building design and construction process has followed the guidelines set by "CasaClima". The building has been modeled in the code of dynamic calculation "Energy Plus" by the Design Builder application and divided it into homogenous thermal zones, characterized by winter indoor temperature set at 20 ° (+ / - 1 °) and summer indoor temperature set at 26 ° (+ / - 1 °). It has modeled: the envelope, as described above, the "free" heat contributions, the air conditioning system, the Mechanical Ventilation system as well as home automation solutions. The air conditioning system is an heat pump, able to guarantee an optimization of energy consumption (in fact, it uses the "free" heat offered by the external environment for conditioning indoor environment). As regards the air recirculation system, it has been used a mechanical ventilation system with internal heat cross-flow exchanger, with an efficiency equal to 50%. The domotic solutions, instead, regard a system for the control of windows external screening using reeds, adjustable as a function of incident solar radiation and a lighting management system adjusted automatically using a dimmer. A so realized building meets the requirement imposed from Italian standard UNI/TS 11300 1, UNI/TS 11300 2 and UNI/TS 11300 3. The analysis was performed according to two different configurations: in "spontaneous-state analysis" (that provides the only energy performance of the structure) and considering the "building-equipments" as a system (which provides the overall performance of the "building system"). The first analysis shows as the absence of thermal mass and the envelope super-heating prevent to incoming heat to exit, overheating the indoor environment. The analysis of the overall performance of the "building system" highlights, instead, as the thermal load is much greater during the summer than in winter; this means that, using a low inertia envelopes, the energy saved in the winter can be used to satisfy the thermal performance in the summer. This is further demonstrated by comparing the performance of indoor temperatures and the relative energy consumption of a similar building with greater thermal inertia. Further analysis involved a critical comparison between the "semisteady-state analysis" ("CasaClima" methodology) and the analysis in dynamic conditions (using "Energy Plus" software).

Solar power. [comparison of costs to wind, nuclear, coal, oil and gas

NASA Technical Reports Server (NTRS)

Walton, A. L.; Hall, Darwin C.

1990-01-01

This paper describes categories of solar technologies and identifies those that are economic. It compares the private costs of power from solar, wind, nuclear, coal, oil, and gas generators. In the southern United States, the private costs of building and generating electricity from new solar and wind power plants are less than the private cost of electricity from a new nuclear power plant. Solar power is more valuable than nuclear power since all solar power is available during peak and midpeak periods. Half of the power from nuclear generators is off-peak power and therefore is less valuable. Reliability is important in determining the value of wind and nuclear power. Damage from air pollution, when factored into the cost of power from fossil fuels, alters the cost comparison in favor of solar and wind power. Some policies are more effective at encouraging alternative energy technologies that pollute less and improve national security.

Nuclear Power in Space

DOE R&D Accomplishments Database

1994-01-01

In the early years of the United States space program, lightweight batteries, fuel cells, and solar modules provided electric power for space missions. As missions became more ambitious and complex, power needs increased and scientists investigated various options to meet these challenging power requirements. One of the options was nuclear energy. By the mid-1950s, research had begun in earnest on ways to use nuclear power in space. These efforts resulted in the first radioisotope thermoelectric generators (RTGs), which are nuclear power generators build specifically for space and special terrestrial uses. These RTGs convert the heat generated from the natural decay of their radioactive fuel into electricity. RTGs have powered many spacecraft used for exploring the outer planets of the solar system and orbiting the sun and Earth. They have also landed on Mars and the moon. They provide the power that enables us to see and learn about even the farthermost objects in our solar system.

76 FR 28459 - Notice of Lodging of Consent Decree Under the Comprehensive Environmental Response, Compensation...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-17

... Response, Compensation, and Liability Act Notice is hereby given that on May 11, 2011, a proposed Consent Decree (the ``Decree'') in United States v. Alsol Corporation, SB Building Associates, Limited Partnership, SB Building GP, L.L.C., United States Land Resources, L.P., United States Realty Resources, Inc...

75 FR 60102 - South Dakota PrairieWinds Project (DOE/EIS-0418)

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-29

... feature 101 wind turbine generators; 6,000 square-foot operations and maintenance building and fence... generation facility that would feature 101 wind turbine generators; 6,000 square-foot operations and... turbine generators, operations and maintenance building and fence perimeter, underground communication...

21. Detail of typical refrigeration unit in the southwest corner ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

21. Detail of typical refrigeration unit in the southwest corner of the fruit and vegetable storage room - Fort Hood, World War II Temporary Buildings, Cold Storage Building, Seventeenth Street, Killeen, Bell County, TX

23. SITE BUILDING 002 SCANNER BUILDING RADAR CONTROL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

23. SITE BUILDING 002 - SCANNER BUILDING - RADAR CONTROL INTERFACE "RCL NO. 2" WITH COMPUTER CONTROL DISC DRIVE UNITS IN FOREGROUND. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

Let's Build: What Materials Will Be Needed? Instructor's Manual. A Resource Unit on Materials Estimation. Building Trades Series.

ERIC Educational Resources Information Center

Mott, Willie J., Comp.

This manual brings together in one package basic knowledges and facts about estimating to assist the building trades instructor in developing his instructional program. Teaching estimating as a separate unit, or integrating it into a regular program are given as two different instructional approaches. After a description of the estimating process…

To redesignate the Federal building and United States Courthouse located at 200 East Wall Street in Midland, Texas, as the "George H. W. Bush and George W. Bush United States Courthouse and George Mahon Federal Building".

THOMAS, 111th Congress

Rep. Conaway, K. Michael [R-TX-11

2009-01-28

House - 01/29/2009 Referred to the Subcommittee on Economic Development, Public Buildings and Emergency Management. (All Actions) Tracker: This bill has the status IntroducedHere are the steps for Status of Legislation:

The Capitol Experience in Washington, D.C.

ERIC Educational Resources Information Center

Dilworth, R. Anne

Designed for 11th grade U.S. history students, the teaching unit combines the history of the U.S. Capitol building and its Greek and Roman revival architecture to tell the story of the nation's government buildings. While the unit uses the U.S. Capitol, any other public building could be used, such as a state capitol, court house, or public…

Non-Intrusive Load Monitoring of HVAC Components using Signal Unmixing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rahimpour, Alireza; Qi, Hairong; Fugate, David L

Heating, Ventilating and Air Conditioning units (HVAC) are a major electrical energy consumer in buildings. Monitoring of the operation and energy consumption of HVAC would increase the awareness of building owners and maintenance service providers of the condition and quality of performance of these units, enabling conditioned-based maintenance which would help achieving higher energy efficiency. In this paper, a novel non-intrusive load monitoring method based on group constrained non-negative matrix factorization is proposed for monitoring the different components of HVAC unit by only measuring the whole building aggregated power signal. At the first level of this hierarchical approach, power consumptionmore » of the building is decomposed to energy consumption of the HVAC unit and all the other electrical devices operating in the building such as lighting and plug loads. Then, the estimated power signal of the HVAC is used for estimating the power consumption profile of the HVAC major electrical loads such as compressors, condenser fans and indoor blower. Experiments conducted on real data collected from a building testbed maintained at the Oak Ridge National Laboratory (ORNL) demonstrate high accuracy on the disaggregation task.« less

24 CFR 983.261 - When occupancy may exceed 25 percent cap on the number of PBV units in each building.

Code of Federal Regulations, 2010 CFR

2010-04-01

... percent cap on the number of PBV units in each building. 983.261 Section 983.261 Housing and Urban...) PROGRAM Occupancy § 983.261 When occupancy may exceed 25 percent cap on the number of PBV units in each... contract for contract units in excess of the 25 percent cap pursuant to § 983.56(a). (b) In referring...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tonnemacher, G.C.; Killen, D.C.; Weinstein, R.E.

This paper reports on the results of an US Department of Energy (DOE) conceptual design evaluation. This is for an early commercial repowering application of advanced circulating pressurized fluidized bed combustion combined cycle technology (APFBC). Here, APFBC would repower an existing generation station, the Carolina Power and Light Company's (CP and L) L.V. Sutton steam station. Repowering concepts are presented for APFBC repowering of Unit 2 (226 MWe) and both Units 1 and 2 in combination (340 MWe total). This evaluation found that it is more economical to repower the existing coal-fired generation unit with APFBC than to build newmore » pulverized coal capacity of equivalent output. The paper provides a review of the DOE study and summarizes the design and costs associated with the APFBC concept. A DOE-sponsored Clean Coal Technology (CCT) demonstration program will pioneer the first commercial APFBC demonstration in year 2001. That 170 MWe APFBC CCT demonstration will use all new equipment, and become the City of Lakeland's C.D. McIntosh, JR. steam plant Unit 4. This all-coal technology is under development by DOE and equipment manufacturers. This paper's concept evaluation is for a larger implementation than the Lakeland McIntosh CCT project. The repowering of L.V. Sutton Unit 2 is projected to boost the energy efficiency of the existing unit from its present 32.0% HHV level to an APFBC-repowered energy efficiency of 42.2% HHV (44.1% LHV). A large frame Westinghouse W501F combustion turbine is modified for APFBC use. This produces a 225+ MWe class APFBC. At this size, APFBC has a wide application for repowering many existing units in America. The paper focuses on the design issues, shows how the APFBC power block integrates with the existing site, and gives a brief summary of the resulting system performance and costs.« less

Center for Corporate Climate Leadership Building Internal Support in Supply Chain Management

EPA Pesticide Factsheets

Organizations build support for addressing GHG emissions by developing key allies in business units, leveraging one business unit to drive change across the organization, and securing executive support while communicating resource needs.

Comparing nurse managers and nurses' perceptions of nurses' self-leadership during capacity building.

PubMed

Jooste, Karien; Cairns, Lindi

2014-05-01

This paper compares the perceptions of nurse managers and nurses about self-leadership of professional nurses while taking ownership of capacity building during unit management. The Nursing Strategy for South Africa states that the competency of nurses is dependent upon factors that lead to capacity building. A quantitative design was followed by conducting a survey. The target population included nurse managers and professional nurses working at an academic public hospital in the Gauteng Province of South Africa. The findings indicate shortcomings in relation to advising professional nurses about self-direction while taking ownership of their daily pressures and stresses associated with unit management. Professional nurses should develop their confidence by focusing on their self-leadership strengths when managing a unit. Recommendations are made to promote self-leadership while taking ownership of nurses during capacity building of unit management. © 2014 John Wiley & Sons Ltd.

A comprehensive study on urban true orthorectification

USGS Publications Warehouse

Zhou, G.; Chen, W.; Kelmelis, J.A.; Zhang, Dongxiao

2005-01-01

To provide some advanced technical bases (algorithms and procedures) and experience needed for national large-scale digital orthophoto generation and revision of the Standards for National Large-Scale City Digital Orthophoto in the National Digital Orthophoto Program (NDOP), this paper presents a comprehensive study on theories, algorithms, and methods of large-scale urban orthoimage generation. The procedures of orthorectification for digital terrain model (DTM)-based and digital building model (DBM)-based orthoimage generation and their mergence for true orthoimage generation are discussed in detail. A method of compensating for building occlusions using photogrammetric geometry is developed. The data structure needed to model urban buildings for accurately generating urban orthoimages is presented. Shadow detection and removal, the optimization of seamline for automatic mosaic, and the radiometric balance of neighbor images are discussed. Street visibility analysis, including the relationship between flight height, building height, street width, and relative location of the street to the imaging center, is analyzed for complete true orthoimage generation. The experimental results demonstrated that our method can effectively and correctly orthorectify the displacements caused by terrain and buildings in urban large-scale aerial images. ?? 2005 IEEE.

Analysis and Optimization of Building Energy Consumption

NASA Astrophysics Data System (ADS)

Chuah, Jun Wei

Energy is one of the most important resources required by modern human society. In 2010, energy expenditures represented 10% of global gross domestic product (GDP). By 2035, global energy consumption is expected to increase by more than 50% from current levels. The increased pace of global energy consumption leads to significant environmental and socioeconomic issues: (i) carbon emissions, from the burning of fossil fuels for energy, contribute to global warming, and (ii) increased energy expenditures lead to reduced standard of living. Efficient use of energy, through energy conservation measures, is an important step toward mitigating these effects. Residential and commercial buildings represent a prime target for energy conservation, comprising 21% of global energy consumption and 40% of the total energy consumption in the United States. This thesis describes techniques for the analysis and optimization of building energy consumption. The thesis focuses on building retrofits and building energy simulation as key areas in building energy optimization and analysis. The thesis first discusses and evaluates building-level renewable energy generation as a solution toward building energy optimization. The thesis next describes a novel heating system, called localized heating. Under localized heating, building occupants are heated individually by directed radiant heaters, resulting in a considerably reduced heated space and significant heating energy savings. To support localized heating, a minimally-intrusive indoor occupant positioning system is described. The thesis then discusses occupant-level sensing (OLS) as the next frontier in building energy optimization. OLS captures the exact environmental conditions faced by each building occupant, using sensors that are carried by all building occupants. The information provided by OLS enables fine-grained optimization for unprecedented levels of energy efficiency and occupant comfort. The thesis also describes a retrofit-oriented building energy simulator, ROBESim, that natively supports building retrofits. ROBESim extends existing building energy simulators by providing a platform for the analysis of novel retrofits, in addition to simulating existing retrofits. Using ROBESim, retrofits can be automatically applied to buildings, obviating the need for users to manually update building characteristics for comparisons between different building retrofits. ROBESim also includes several ease-of-use enhancements to support users of all experience levels.

A Rationale for Building a Comprehensive Science Program for Inner-City Education.

ERIC Educational Resources Information Center

Martin, Charles Arthur

The intent of this dissertation was to develop a science curriculum from an inner-city perspective. Five units and a rationale for inner-city education are included. The units include both physical and biological science topics. The units are as follows: (1) Rationale for Building a Comprehensive Science Program for Inner-City Education; (2) With…

Overview of Commercial Buildings, 2003

EIA Publications

2008-01-01

The Energy Information Administration conducts the Commercial Buildings Energy Consumption Survey (CBECS) to collect information on energy-related building characteristics and types and amounts of energy consumed in commercial buildings in the United States.

Distributed Generation Market Demand Model (dGen): Documentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sigrin, Benjamin; Gleason, Michael; Preus, Robert

The Distributed Generation Market Demand model (dGen) is a geospatially rich, bottom-up, market-penetration model that simulates the potential adoption of distributed energy resources (DERs) for residential, commercial, and industrial entities in the continental United States through 2050. The National Renewable Energy Laboratory (NREL) developed dGen to analyze the key factors that will affect future market demand for distributed solar, wind, storage, and other DER technologies in the United States. The new model builds off, extends, and replaces NREL's SolarDS model (Denholm et al. 2009a), which simulates the market penetration of distributed PV only. Unlike the SolarDS model, dGen can modelmore » various DER technologies under one platform--it currently can simulate the adoption of distributed solar (the dSolar module) and distributed wind (the dWind module) and link with the ReEDS capacity expansion model (Appendix C). The underlying algorithms and datasets in dGen, which improve the representation of customer decision making as well as the spatial resolution of analyses (Figure ES-1), also are improvements over SolarDS.« less

Cadmium Recycling in the United States in 2000

USGS Publications Warehouse

Plachy, Jozef

2003-01-01

Recycling of cadmium is a young and growing industry that has been influenced by environmental concerns and regulatory constraints. Domestic recycling of cadmium began in 1989 as a byproduct of processing of spent nickel-cadmium batteries. In 1995, International Metals Reclamation Co. Inc. expanded its operations by building a dedicated cadmium recycling plant. In 2000, an estimated 13 percent of cadmium consumption in the United States was sourced from recycled cadmium, which is derived mainly from old scrap or, to lesser degree, new scrap. The easiest forms of old scrap to recycle are small spent nickel-cadmium batteries followed by flue dust generated during recycling of galvanized steel and small amounts of alloys that contain cadmium. Most of new scrap is generated during manufacturing processes, such as nickel-cadmium battery production. All other uses of cadmium are in low concentrations and, therefore, difficult to recycle. Consequently, much of this cadmium is dissipated and lost. The amount of cadmium in scrap that was unrecovered in 2000 was estimated to be 2,030 t, and an estimated 285 t was recovered. Recycling efficiency was estimated to be about 15 percent.

Cadmium recycling in the United States in 2000

USGS Publications Warehouse

Plachy, Jozef

2003-01-01

Recycling of cadmium is a young and growing industry that has been influenced by environmental concerns and regulatory constraints. Domestic recycling of cadmium began in 1989 as a byproduct of processing of spent nickel-cadmium batteries. In 1995, International Metals Reclamation Co. Inc. expanded its operations by building a dedicated cadmium recycling plant. In 2000, an estimated 13 percent of cadmium consumption in the United States was sourced from recycled cadmium, which is derived mainly from old scrap or, to lesser degree, new scrap. The easiest forms of old scrap to recycle are small spent nickel-cadmium batteries followed by flue dust generated during recycling of galvanized steel and small amounts of alloys that contain cadmium. Most of new scrap is generated during manufacturing processes, such as nickel-cadmium battery production. All other uses of cadmium are in low concentrations and, therefore, difficult to recycle. Consequently, much of this cadmium is dissipated and lost. The amount of cadmium in scrap that was unrecovered in 2000 was estimated to be 2,030 metric tons, and an estimated 285 tons was recovered. Recycling efficiency was estimated to be about 15 percent.

Factors related to building loss due to wildfires in the conterminous United States.

PubMed

Alexandre, Patricia M; Stewart, Susan I; Keuler, Nicholas S; Clayton, Murray K; Mockrin, Miranda H; Bar-Massada, Avi; Syphard, Alexandra D; Radeloff, Volker C

2016-10-01

Wildfire is globally an important ecological disturbance affecting biochemical cycles and vegetation composition, but also puts people and their homes at risk. Suppressing wildfires has detrimental ecological effects and can promote larger and more intense wildfires when fuels accumulate, which increases the threat to buildings in the wildland-urban interface (WUI). Yet, when wildfires occur, typically only a small proportion of the buildings within the fire perimeter are lost, and the question is what determines which buildings burn. Our goal was to examine which factors are related to building loss when a wildfire occurs throughout the United States. We were particularly interested in the relative roles of vegetation, topography, and the spatial arrangement of buildings, and how their respective roles vary among ecoregions. We analyzed all fires that occurred within the conterminous United States from 2000 to 2010 and digitized which buildings were lost and which survived according to Google Earth historical imagery. We modeled the occurrence as well as the percentage of buildings lost within clusters using logistic and linear regression. Overall, variables related to topography and the spatial arrangement of buildings were more frequently present in the best 20 regression models than vegetation-related variables. In other words, specific locations in the landscape have a higher fire risk, and certain development patterns can exacerbate that risk. Fire policies and prevention efforts focused on vegetation management are important, but insufficient to solve current wildfire problems. Furthermore, the factors associated with building loss varied considerably among ecoregions suggesting that fire policy applied uniformly across the United States will not work equally well in all regions and that efforts to adapt communities to wildfires must be regionally tailored. © 2016 by the Ecological Society of America.

An Early Look at Building a Social Learning for Sustainability Community of Practice: RCE Grand Rapids' Flagship Project

ERIC Educational Resources Information Center

Glasser, Harold

2010-01-01

Grand Rapids is the first United Nations University (UNU) Regional Centre of Expertise (RCE) on education for sustainable development (ESD) in the United States. It builds on the region's long history and deep foundation in research, planning and problem solving to build a sustainable future. This article explores the concept of RCEs as social…

An estimation framework for building information modeling (BIM)-based demolition waste by type.

PubMed

Kim, Young-Chan; Hong, Won-Hwa; Park, Jae-Woo; Cha, Gi-Wook

2017-12-01

Most existing studies on demolition waste (DW) quantification do not have an official standard to estimate the amount and type of DW. Therefore, there are limitations in the existing literature for estimating DW with a consistent classification system. Building information modeling (BIM) is a technology that can generate and manage all the information required during the life cycle of a building, from design to demolition. Nevertheless, there has been a lack of research regarding its application to the demolition stage of a building. For an effective waste management plan, the estimation of the type and volume of DW should begin from the building design stage. However, the lack of tools hinders an early estimation. This study proposes a BIM-based framework that estimates DW in the early design stages, to achieve an effective and streamlined planning, processing, and management. Specifically, the input of construction materials in the Korean construction classification system and those in the BIM library were matched. Based on this matching integration, the estimates of DW by type were calculated by applying the weight/unit volume factors and the rates of DW volume change. To verify the framework, its operation was demonstrated by means of an actual BIM modeling and by comparing its results with those available in the literature. This study is expected to contribute not only to the estimation of DW at the building level, but also to the automated estimation of DW at the district level.

Distributed Energy Planning for Climate Resilience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stout, Sherry R; Hotchkiss, Elizabeth L; Day, Megan H

At various levels of government across the United States and globally climate resilient solutions are being adopted and implemented. Solutions vary based on predicted hazards, community context, priorities, complexity, and available resources. Lessons are being learned through the implementation process, which can be replicated regardless of level or type of government entity carrying out the resiliency planning. Through a number of analyses and technical support across the world, NREL has learned key lessons related to resilience planning associated with power generation and water distribution. Distributed energy generation is a large factor in building resilience with clean energy technologies and solutions.more » The technical and policy solutions associated with distributed energy implementation for resilience fall into a few major categories, including spatial diversification, microgrids, water-energy nexus, policy, and redundancy.« less

An Operations Concept for the Next Generation VLA

NASA Astrophysics Data System (ADS)

Kepley, Amanda; McKinnon, Mark; Selina, Rob; Murphy, Eric Joseph; ngVLA project

2018-01-01

This poster presents an operations plan for the next generation VLA (ngVLA), which is a proposed 214 element interferometer operating from ~1-115GHz, located in the southwestern United States. The operations requirements for this instrument are driven by the large number of antennas spread out over a multi-state area and a cap on the operations budget of 3 times that of the current VLA. These constraints require that the maintenance is a continuous process and that individual antennas are self-sufficient, making flexible subarrays crucial. The ngVLA will produce science ready data products for its users, building on the pioneering work being currently done at ALMA and the JVLA. Finally, the ngVLA will adopt a user support model similar to those at other large facilities (ALMA, HST, JWST, etc).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steinberg, Daniel; Bielen, Dave; Eichman, Josh

Electrification of end-use services in the transportation, buildings, and industrial sectors coupled with decarbonization of electricity generation has been identified as one of the key pathways to achieving a low-carbon future in the United States. By lowering the carbon intensity of the electricity generation and substituting electricity for higher-emissions fossil fuels in end-use sectors, significant reductions in carbon dioxide emissions can be achieved. This report describes a preliminary analysis that examines the potential impacts of widespread electrification on the U.S. energy sector. We develop a set of exploratory scenarios under which electrification is aggressively pursued across all end-use sectors andmore » examine the impacts of achieving these electrification levels on electricity load patterns, total fossil energy consumption, carbon dioxide emissions, and the evolution of the U.S. power system.« less

Solar Mirror Fabrication in the Technical Services Building

NASA Image and Video Library

1966-02-21

Daniel Bernatowicz, Chief of the Advanced Power Systems Branch at the National Aeronautics and Space Administration (NASA) Lewis Research Center, examines a 20-foot section of a solar mirror being fabricated in the Jig Bore Room of the Technical Services Building. NASA Lewis was conducting a wide-ranging effort to explore methods of generating electrical power for spacecraft. One method employed a large parabolic mirror to concentrate the sun’s energy. The mirror had to remain rigid and withstand micrometeoroids, but remain light and compact enough to be easily launched. In 1963 Bernatowicz and his researchers undertook a program to design a solar mirror to work with the Brayton cycle system on a space station. The mirror in this photograph was prepared for a conference on Advanced Technology in Space Power Systems held at Lewis in late August 1966. Lewis experts discussed advances with batteries, fuel cells, isotope and thermoelectric generators, and the SNAP-8 space power system. Lewis was developing several types of solar mirrors to work with a Brayton cycle electric generating system. The mirror’s 12 sections were shaped using a unique forming process developed at Lewis, coated with an epoxy, and plated with aluminum. The mirror concentrated the Sun's rays on a heat storage receiver containing lithium fluoride. This material was heated to produce power in a turbogenerator system, while additional heat was stored for use when the unit was in the Earth's shadow.

The role of education in the culture of four pillar poverty to establish the nationalism of young generation

NASA Astrophysics Data System (ADS)

Sarmini; Warsono

2018-01-01

Globalization as an international integration process brings several positive and negative impacts due to the exchange of world views, products, thoughts, and other cultural aspects that can diminish the values of national identity. Four pillars of nationality are needed as a foundation to counteract the negative effects of globalization, therefore a culturally, educative, legal and structural approach is needed so that the younger generation can truly understand and safeguard the four pillars of our nationality. So far the government has also played little role in building the four pillars into an education. This research intends to see how the role of education can build young generation of nationalism by using research design in the form of content analysis. The population in this study is the Education Office of Sidoarjo Regency, which is the level of Junior High School Education Unit. However, given the scope and breadth of the district of Sidoarjo, a representative sample is determined using FGD (Focus Group Discussion) data collection techniques and questionnaires that will be analyzed using written policy descriptions or unwritten policies. Through a series of research stages, it can be concluded that there are still many principals who have not integrated the culture of the four pillars of nationalism into a written and unwritten document covering intracurricular, extracurricular, school culture and through community participation.

KSC-2011-6818

NASA Image and Video Library

2011-09-08

CAPE CANAVERAL, Fla. -- On Cape Canaveral Air Force Station in Florida, United Launch Alliance (ULA) personnel in the Delta Operations Building prepare for the launch of NASA's Gravity Recovery and Interior Laboratory mission aboard a ULA Delta II Heavy rocket. Physical control of the rocket is maintained from the building, located about a mile from Space Launch Complex 17B. The room functions as a "soft blockhouse" and is the room from which the computer-generated command to launch the rocket is issued two seconds before liftoff. Launch is scheduled for 8:37:06 a.m. EDT Sept. 8. GRAIL will fly twin spacecraft in tandem around the moon to precisely measure and map variations in the moon's gravitational field. The mission will provide the most accurate global gravity field to date for any planet, including Earth. For more information, visit http://www.nasa.gov/grail. Photo credit: NASA/Kim Shiflett

KSC-2011-6817

NASA Image and Video Library

2011-09-08

CAPE CANAVERAL, Fla. -- On Cape Canaveral Air Force Station in Florida, United Launch Alliance (ULA) personnel in the Delta Operations Building prepare for the launch of NASA's Gravity Recovery and Interior Laboratory mission aboard a ULA Delta II Heavy rocket. Physical control of the rocket is maintained from the building, located about a mile from Space Launch Complex 17B. The room functions as a "soft blockhouse" and is the room from which the computer-generated command to launch the rocket is issued two seconds before liftoff. Launch is scheduled for 8:37:06 a.m. EDT Sept. 8. GRAIL will fly twin spacecraft in tandem around the moon to precisely measure and map variations in the moon's gravitational field. The mission will provide the most accurate global gravity field to date for any planet, including Earth. For more information, visit http://www.nasa.gov/grail. Photo credit: NASA/Kim Shiflett

KSC-2011-6816

NASA Image and Video Library

2011-09-08

CAPE CANAVERAL, Fla. -- On Cape Canaveral Air Force Station in Florida, United Launch Alliance (ULA) personnel in the Delta Operations Building prepare for the launch of NASA's Gravity Recovery and Interior Laboratory mission aboard a ULA Delta II Heavy rocket. Physical control of the rocket is maintained from the building, located about a mile from Space Launch Complex 17B. The room functions as a "soft blockhouse" and is the room from which the computer-generated command to launch the rocket is issued two seconds before liftoff. Launch is scheduled for 8:37:06 a.m. EDT Sept. 8. GRAIL will fly twin spacecraft in tandem around the moon to precisely measure and map variations in the moon's gravitational field. The mission will provide the most accurate global gravity field to date for any planet, including Earth. For more information, visit http://www.nasa.gov/grail. Photo credit: NASA/Kim Shiflett

Scaling Retro-Commissioning to Small Commercial Buildings: A Turnkey Automated Hardware-Software Solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Guanjing; Granderson, J.; Brambley, Michael R.

2015-07-01

In the United States, small commercial buildings represent 51% of total floor space of all commercial buildings and consume nearly 3 quadrillion Btu (3.2 quintillion joule) of site energy annually, presenting an enormous opportunity for energy savings. Retro-commissioning (RCx), the process through which professional energy service providers identify and correct operational problems, has proven to be a cost-effective means to achieve median energy savings of 16%. However, retro-commissioning is not typically conducted at scale throughout the commercial stock. Very few small commercial buildings are retro-commissioned because utility expenses are relatively modest, margins are tighter, and capital for improvements is limited.more » In addition, small buildings do not have in-house staff with the expertise to identify improvement opportunities. In response, a turnkey hardware-software solution was developed to enable cost-effective, monitoring-based RCx of small commercial buildings. This highly tailored solution enables non-commissioning providers to identify energy and comfort problems, as well as associated cost impacts and remedies. It also facilitates scale by offering energy service providers the means to streamline their existing processes and reduce costs by more than half. The turnkey RCx sensor suitcase consists of two primary components: a suitcase of sensors for short-term building data collection that guides users through the process of deploying and retrieving their data and a software application that automates analysis of sensor data, identifies problems and generates recommendations. This paper presents the design and testing of prototype models, including descriptions of the hardware design, analysis algorithms, performance testing, and plans for dissemination.« less

Yahoo! Compute Coop (YCC). A Next-Generation Passive Cooling Design for Data Centers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robison, AD; Page, Christina; Lytle, Bob

The purpose of the Yahoo! Compute Coop (YCC) project is to research, design, build and implement a greenfield "efficient data factory" and to specifically demonstrate that the YCC concept is feasible for large facilities housing tens of thousands of heat-producing computing servers. The project scope for the Yahoo! Compute Coop technology includes: - Analyzing and implementing ways in which to drastically decrease energy consumption and waste output. - Analyzing the laws of thermodynamics and implementing naturally occurring environmental effects in order to maximize the "free-cooling" for large data center facilities. "Free cooling" is the direct usage of outside air tomore » cool the servers vs. traditional "mechanical cooling" which is supplied by chillers or other Dx units. - Redesigning and simplifying building materials and methods. - Shortening and simplifying build-to-operate schedules while at the same time reducing initial build and operating costs. Selected for its favorable climate, the greenfield project site is located in Lockport, NY. Construction on the 9.0 MW critical load data center facility began in May 2009, with the fully operational facility deployed in September 2010. The relatively low initial build cost, compatibility with current server and network models, and the efficient use of power and water are all key features that make it a highly compatible and globally implementable design innovation for the data center industry. Yahoo! Compute Coop technology is designed to achieve 99.98% uptime availability. This integrated building design allows for free cooling 99% of the year via the building's unique shape and orientation, as well as server physical configuration.« less

Social Media Technology and Public Health in Ontario: Findings from a Planning Meeting Exploring Current Practices and Future Research Directions.

PubMed

Booth, Richard; McMurray, Josephine; Regan, Sandra; Kothari, Anita; Donelle, Lorie; McBride, Susan; Sobel, Annette; Hall, Jodi; Fraser, Robert; Foisey, Lyndsay

2017-01-01

In the province of Ontario, many of the public health units (PHUs) now possess and use social media as part of their daily health promotion and communication operations. To explore this topic, a planning meeting was held to generate deeper insights toward the use of these forms of technology for preventative services delivery. The planning meeting was held with 50 participants, comprising representatives from 20 of the 36 PHUs in Ontario, interested academics, students and government representatives. A nominal group technique (NGT) was used to build consensus related to future research needs, as related to public health and social media. Participants generated a range of insights around the use of social media, including the need for: leadership buy-in and resource allocation; social media policy and governance structure; performance measurement and evaluation; practices related to engagement with program recipients and addressing the lack of resources faced by many health units. Future research priorities were also generated, related to evaluating the cost-benefit of social media activities and understanding behaviour change implications. Further research is needed to evaluate the functionality, leadership and competency requirements and impact(s) of these new forms of health communication technology within public health service delivery. Copyright © 2017 Longwoods Publishing.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Townsend, M.W.

The Monsanto Chemical Company operates a plastics and resins plant located in Addyston, Ohio. The process equipment requires routine rinsing with technical grade acetone between batches. Due to the volumes of spent acetone generated and the associated RCRA hazardous waste regulations, the plant sought to recycle and reuse the acetone to reduce the purchase cost of virgin acetone and the cost of spent acetone disposal. One of the first options explored was package unit distillation units. The cost of these units was in the $20--$30,000 range in 1989 dollars. Even though the cost of a package unit was not deemedmore » unreasonable, there were additional costs and concerns that led to elimination of this option. The unit would have required additional manpower to operate and maintain, i.e., at least a fraction of an operator and mechanic. For plant safety reasons, it was desired to operate this package unit outside the production building, thus construction of an outbuilding would have added to the expense of the project. Additionally, there were concerns of package unit reliability. During this evaluation, tractor-trailer mounted distillation units were discovered. The portable units were equipped with either thin-film evaporator technology capable of processing 240 to 480 gallons per hour, or pot still (batch) distillation technology capable of rates from 120 to 240 gallons per hour. Both units were constructed of stainless steel.« less

Modeling Environmental Tobacco Smoke (ETS) Infiltration in Low-Income Multifamily Housing before and after Building Energy Retrofits

PubMed Central

Fabian, Maria Patricia; Lee, Sharon Kitman; Underhill, Lindsay Jean; Vermeer, Kimberly; Adamkiewicz, Gary; Levy, Jonathan Ian

2016-01-01

Secondhand exposure to environmental tobacco smoke (ETS) in multifamily housing remains a health concern despite strong recommendations to implement non-smoking policies. Multiple studies have documented exposure to ETS in non-smoking units located in buildings with smoking units. However, characterizing the magnitude of ETS infiltration or measuring the impact of building interventions or resident behavior on ETS is challenging due to the complexities of multifamily buildings, which include variable resident behaviors and complex airflows between numerous shared compartments (e.g., adjacent apartments, common hallways, elevators, heating, ventilating and air conditioning (HVAC) systems, stack effect). In this study, building simulation models were used to characterize changes in ETS infiltration in a low income, multifamily apartment building in Boston which underwent extensive building renovations targeting energy savings. Results suggest that exterior wall air sealing can lead to increases in ETS infiltration across apartments, while compartmentalization can reduce infiltration. The magnitude and direction of ETS infiltration depends on apartment characteristics, including construction (i.e., level and number of exterior walls), resident behavior (e.g., window opening, operation of localized exhaust fans), and seasonality. Although overall ETS concentrations and infiltration were reduced post energy-related building retrofits, these trends were not generalizable to all building units. Whole building smoke-free policies are the best approach to eliminate exposure to ETS in multifamily housing. PMID:26999174

Modeling Environmental Tobacco Smoke (ETS) Infiltration in Low-Income Multifamily Housing before and after Building Energy Retrofits.

PubMed

Fabian, Maria Patricia; Lee, Sharon Kitman; Underhill, Lindsay Jean; Vermeer, Kimberly; Adamkiewicz, Gary; Levy, Jonathan Ian

2016-03-16

Secondhand exposure to environmental tobacco smoke (ETS) in multifamily housing remains a health concern despite strong recommendations to implement non-smoking policies. Multiple studies have documented exposure to ETS in non-smoking units located in buildings with smoking units. However, characterizing the magnitude of ETS infiltration or measuring the impact of building interventions or resident behavior on ETS is challenging due to the complexities of multifamily buildings, which include variable resident behaviors and complex airflows between numerous shared compartments (e.g., adjacent apartments, common hallways, elevators, heating, ventilating and air conditioning (HVAC) systems, stack effect). In this study, building simulation models were used to characterize changes in ETS infiltration in a low income, multifamily apartment building in Boston which underwent extensive building renovations targeting energy savings. Results suggest that exterior wall air sealing can lead to increases in ETS infiltration across apartments, while compartmentalization can reduce infiltration. The magnitude and direction of ETS infiltration depends on apartment characteristics, including construction (i.e., level and number of exterior walls), resident behavior (e.g., window opening, operation of localized exhaust fans), and seasonality. Although overall ETS concentrations and infiltration were reduced post energy-related building retrofits, these trends were not generalizable to all building units. Whole building smoke-free policies are the best approach to eliminate exposure to ETS in multifamily housing.

Constructing Wood Agricultural Buildings. An Instructional Unit for High School Teachers of Vocational Agriculture.

ERIC Educational Resources Information Center

Williams, Paul; Carpenter, Bruce

This 5-week unit on constructing wood agricultural buildings is designed for the junior or senior year of the regular agribusiness course of study or as part of the agricultural mechanics program. In outline form, the unit is divided into eight major performance objectives. Each objective is subdivided into the areas of content, suggested…

Lake Erie...Build a Fish to Scale!

ERIC Educational Resources Information Center

Canning, Maureen; Dunlevy, Margie

This elementary school teaching unit was developed as a part of a series of teaching units that deal with Lake Erie. This unit was developed to enable children to: (1) name the different parts of a fish; (2) assemble a fish using overlapping overheads to reinforce fish parts; (3) build a fish to scale using jumbo fish puzzle parts; (4) classify…

Halogen dependent symmetry change in two series of wheel cluster organic frameworks built from La18 tertiary building units.

PubMed

Fang, Wei-Hui; Zhang, Lei; Zhang, Jian; Yang, Guo-Yu

2016-01-25

Two series of wheel cluster organic frameworks (WCOFs) built from La18 tertiary building units are hydrothermally made, which show halogen-dependent structural symmetry, and demonstrate different chiral performances.

7 CFR 1806.25 - Conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE...-unit housing facilities. (1) If the financial assistance is to buy a dwelling or multi-unit housing...) Nonresidential buildings. Construction plans and specifications for new buildings or improvements to existing...

Cost-effective retrofit technology for reducing peak power demand in small and medium commercial buildings

DOE PAGES

Nutaro, James J.; Fugate, David L.; Kuruganti, Teja; ...

2015-05-27

We describe a cost-effective retrofit technology that uses collective control of multiple rooftop air conditioning units to reduce the peak power consumption of small and medium commercial buildings. The proposed control uses a model of the building and air conditioning units to select an operating schedule for the air conditioning units that maintains a temperature set point subject to a constraint on the number of units that may operate simultaneously. A prototype of this new control system was built and deployed in a large gymnasium to coordinate four rooftop air conditioning units. Based on data collected while operating this prototype,more » we estimate that the cost savings achieved by reducing peak power consumption is sufficient to repay the cost of the prototype within a year.« less

Building the Plane Inflight: Observations from Case Studies in Wartime Flight Training for Partner Nations

DTIC Science & Technology

2016-05-26

guidance on how to build an effective SC program. Whether used as pre-decisional guides or ex post facto evaluation tools, they fall short of...Building the Plane Inflight: Observations from Case Studies in Wartime Flight Training for Partner...Nations A Monograph by Major Timothy J. Day United States Air Force School of Advanced Military Studies United States Army Command and General

Controllable Synthesis of Tunable Microstructures of Self-Supporting Graphene Films from Opened Bubble to Cube via in Situ Template-Modulating.

PubMed

Li, Na; Yang, Qiao; Liu, Xing; Huang, Xuankai; Zhang, Haiyan; Wang, Chengxin

2017-12-06

Three-dimensional (3D) microstructured building units have replaced layer-to-layer stacked designs in transparent graphene films to fully exploit the advantages of two-dimensional graphene. However, it is still challenging to precisely control the size and microstructures of these building blocks to develop multifunctional graphene-based materials that satisfy the performance requirements of diverse applications. In this study, we propose a controllable method to regulate the microstructures of building units to form structures ranging from opened bubbles and cubes, while the size decreased from 20 to 3 μm, via an in situ template-modulating technology. NaCl was used as either a liquid or solid template by changing the dc bias. The reduced size and dense arrangement of the building units not only provide an improved mass loading for the transparent films but also build multiple pathways for fast ion/electron transmission, enhancing their promise for various practical applications. Generally, we provide a convenient protocol for finely regulating the microstructure and size of these building units, resulting in multifunctional films with a controllable transmittance, which enables the use of these graphene-based architectures as transparent electrodes in various applications and extends the family of multifunctional materials that will present new possibilities for electronics and other devices.

Building Damage Assessment after Earthquake Using Post-Event LiDAR Data

NASA Astrophysics Data System (ADS)

Rastiveis, H.; Eslamizade, F.; Hosseini-Zirdoo, E.

2015-12-01

After an earthquake, damage assessment plays an important role in leading rescue team to help people and decrease the number of mortality. Damage map is a map that demonstrates collapsed buildings with their degree of damage. With this map, finding destructive buildings can be quickly possible. In this paper, we propose an algorithm for automatic damage map generation after an earthquake using post-event LiDAR Data and pre-event vector map. The framework of the proposed approach has four main steps. To find the location of all buildings on LiDAR data, in the first step, LiDAR data and vector map are registered by using a few number of ground control points. Then, building layer, selected from vector map, are mapped on the LiDAR data and all pixels which belong to the buildings are extracted. After that, through a powerful classifier all the extracted pixels are classified into three classes of "debris", "intact building" and "unclassified". Since textural information make better difference between "debris" and "intact building" classes, different textural features are applied during the classification. After that, damage degree for each candidate building is estimated based on the relation between the numbers of pixels labelled as "debris" class to the whole building area. Calculating the damage degree for each candidate building, finally, building damage map is generated. To evaluate the ability proposed method in generating damage map, a data set from Port-au-Prince, Haiti's capital after the 2010 Haiti earthquake was used. In this case, after calculating of all buildings in the test area using the proposed method, the results were compared to the damage degree which estimated through visual interpretation of post-event satellite image. Obtained results were proved the reliability of the proposed method in damage map generation using LiDAR data.

The impact of team building on communication and job satisfaction of nursing staff.

PubMed

Amos, Mary Anne; Hu, Jie; Herrick, Charlotte A

2005-01-01

A series of team-building activities were conducted on a medical-surgical unit and their impact on staff's communication and job satisfaction was examined. Forty-four unit personnel participated in the interventions. Staff communication and job satisfaction were measured before and after the intervention. The findings linked team-building activities with improved staff communication and job satisfaction. Team-building strategies assisted the nurse leader/manager to build an effective work team by strengthening communication and interpersonal relationships so that the staff could function as a more cohesive group. Staff development consultants can help nurse managers become more effective team leaders by identifying the necessary resources and by helping to plan and coordinate team-building strategies.

11. BUILDING NO. 18 (ENGINEERING BUILDING), CENTER, IN RELATION TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. BUILDING NO. 18 (ENGINEERING BUILDING), CENTER, IN RELATION TO BUILDING NO. 19 (BENDING SHOP AND OVEN) AT FAR LEFT, AND TO THE WET BASIN AT FAR RIGHT. VIEW TO NORTH-NORTHWEST. - United Engineering Company Shipyard, 2900 Main Street, Alameda, Alameda County, CA

Literature search strategies for conducting knowledge-building and theory-generating qualitative systematic reviews.

PubMed

Finfgeld-Connett, Deborah; Johnson, E Diane

2013-01-01

To report literature search strategies for the purpose of conducting knowledge-building and theory-generating qualitative systematic reviews. Qualitative systematic reviews lie on a continuum from knowledge-building and theory-generating to aggregating and summarizing. Different types of literature searches are needed to optimally support these dissimilar reviews. Articles published between 1989-Autumn 2011. These documents were identified using a hermeneutic approach and multiple literature search strategies. Redundancy is not the sole measure of validity when conducting knowledge-building and theory-generating systematic reviews. When conducting these types of reviews, literature searches should be consistent with the goal of fully explicating concepts and the interrelationships among them. To accomplish this objective, a 'berry picking' approach is recommended along with strategies for overcoming barriers to finding qualitative research reports. To enhance integrity of knowledge-building and theory-generating systematic reviews, reviewers are urged to make literature search processes as transparent as possible, despite their complexity. This includes fully explaining and rationalizing what databases were used and how they were searched. It also means describing how literature tracking was conducted and grey literature was searched. In the end, the decision to cease searching also needs to be fully explained and rationalized. Predetermined linear search strategies are unlikely to generate search results that are adequate for purposes of conducting knowledge-building and theory-generating qualitative systematic reviews. Instead, it is recommended that iterative search strategies take shape as reviews evolve. © 2012 Blackwell Publishing Ltd.

Quantifying the hurricane risk to offshore wind turbines.

PubMed

Rose, Stephen; Jaramillo, Paulina; Small, Mitchell J; Grossmann, Iris; Apt, Jay

2012-02-28

The U.S. Department of Energy has estimated that if the United States is to generate 20% of its electricity from wind, over 50 GW will be required from shallow offshore turbines. Hurricanes are a potential risk to these turbines. Turbine tower buckling has been observed in typhoons, but no offshore wind turbines have yet been built in the United States. We present a probabilistic model to estimate the number of turbines that would be destroyed by hurricanes in an offshore wind farm. We apply this model to estimate the risk to offshore wind farms in four representative locations in the Atlantic and Gulf Coastal waters of the United States. In the most vulnerable areas now being actively considered by developers, nearly half the turbines in a farm are likely to be destroyed in a 20-y period. Reasonable mitigation measures--increasing the design reference wind load, ensuring that the nacelle can be turned into rapidly changing winds, and building most wind plants in the areas with lower risk--can greatly enhance the probability that offshore wind can help to meet the United States' electricity needs.

Quantifying the hurricane risk to offshore wind turbines

PubMed Central

Rose, Stephen; Jaramillo, Paulina; Small, Mitchell J.; Grossmann, Iris; Apt, Jay

2012-01-01

The U.S. Department of Energy has estimated that if the United States is to generate 20% of its electricity from wind, over 50 GW will be required from shallow offshore turbines. Hurricanes are a potential risk to these turbines. Turbine tower buckling has been observed in typhoons, but no offshore wind turbines have yet been built in the United States. We present a probabilistic model to estimate the number of turbines that would be destroyed by hurricanes in an offshore wind farm. We apply this model to estimate the risk to offshore wind farms in four representative locations in the Atlantic and Gulf Coastal waters of the United States. In the most vulnerable areas now being actively considered by developers, nearly half the turbines in a farm are likely to be destroyed in a 20-y period. Reasonable mitigation measures—increasing the design reference wind load, ensuring that the nacelle can be turned into rapidly changing winds, and building most wind plants in the areas with lower risk—can greatly enhance the probability that offshore wind can help to meet the United States’ electricity needs. PMID:22331894

New Compressor Added to Glenn's 450- psig Combustion Air System

NASA Technical Reports Server (NTRS)

Swan, Jeffrey A.

2000-01-01

In September 1999, the Central Process Systems Engineering Branch and the Maintenance and the Central Process Systems Operations Branch, released for service a new high pressure compressor to supplement the 450-psig Combustion Air System at the NASA Glenn Research Center at Lewis Field. The new compressor, designated C-18, is located in Glenn s Central Air Equipment Building and is remotely operated from the Central Control Building. C-18 can provide 40 pounds per second (pps) of airflow at pressure to our research customers. This capability augments our existing system capacity (compressors C 4 at 38 pps and C-5 at 32 pps), which is generated from Glenn's Engine Research Building. The C-18 compressor was originally part of Glenn's 21-Inch Hypersonic Tunnel, which was transferred from the Jet Propulsion Laboratory to Glenn in the mid-1980's. With the investment of construction of facilities funding, the compressor was modified, new mechanical and electrical support equipment were purchased, and the unit was installed in the basement of the Central Air Equipment Building. After several weeks of checkout and troubleshooting, the new compressor was ready for long-term, reliable operations. With a total of 110 pps in airflow now available, Glenn is well positioned to support the high-pressure air test requirements of our research customers.

Failure analysis of fractured capscrews in centrifugal coolant compressor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Witherell, C.E.

1985-03-25

This study was made to determine the cause of failure of capscrews that retain a baffle plate in a Freon 11 centrifugal compressor manufactured by the Trane Company. The affected unit is installed in Building 490 at LLNL. The capscrews failed through hydrogen embrittlement. The source for hydrogen appears to have been corrosion. In a dissimilar metal couple of aluminum and uncoated high strength, highly-stressed steel, corrosive environments would generate hydrogen at the the steel side of the couple and embrittle it. There is no evidence that the manufacturer took precautions to prevent such an occurrence.

Representation of viruses in the remediated PDB archive

PubMed Central

Lawson, Catherine L.; Dutta, Shuchismita; Westbrook, John D.; Henrick, Kim; Berman, Helen M.

2008-01-01

A new scheme has been devised to represent viruses and other biological assemblies with regular noncrystallographic symmetry in the Protein Data Bank (PDB). The scheme describes existing and anticipated PDB entries of this type using generalized descriptions of deposited and experimental coordinate frames, symmetry and frame transformations. A simplified notation has been adopted to express the symmetry generation of assemblies from deposited coordinates and matrix operations describing the required point, helical or crystallographic symmetry. Complete correct information for building full assemblies, subassemblies and crystal asymmetric units of all virus entries is now available in the remediated PDB archive. PMID:18645236

Foundational Security Principles for Medical Application Platforms* (Extended Abstract)

PubMed Central

Vasserman, Eugene Y.; Hatcliff, John

2014-01-01

We describe a preliminary set of security requirements for safe and secure next-generation medical systems, consisting of dynamically composable units, tied together through a real-time safety-critical middleware. We note that this requirement set is not the same for individual (stand-alone) devices or for electronic health record systems, and we must take care to define system-level requirements rather than security goals for components. The requirements themselves build on each other such that it is difficult or impossible to eliminate any one of the requirements and still achieve high-level security goals. PMID:25599096

Stratification of a cityscape using census and land use variables for inventory of building materials

USGS Publications Warehouse

Rosenfield, G.H.; Fitzpatrick-Lins, K.; Johnson, T.L.

1987-01-01

A cityscape (or any landscape) can be stratified into environmental units using multiple variables of information. For the purposes of sampling building materials, census and land use variables were used to identify similar strata. In the Metropolitan Statistical Area of a cityscape, the census tract is the smallest unit for which census data are summarized and digitized boundaries are available. For purposes of this analysis, census data on total population, total number of housing units, and number of singleunit dwellings were aggregated into variables of persons per square kilometer and proportion of housing units in single-unit dwellings. The level 2 categories of the U.S. Geological Survey's land use and land cover data base were aggregated into variables of proportion of residential land with buildings, proportion of nonresidential land with buildings, and proportion of open land. The cityscape was stratified, from these variables, into environmental strata of Urban Central Business District, Urban Livelihood Industrial Commercial, Urban Multi-Family Residential, Urban Single Family Residential, Non-Urban Suburbanizing, and Non-Urban Rural. The New England region was chosen as a region with commonality of building materials, and a procedure developed for trial classification of census tracts into one of the strata. Final stratification was performed by discriminant analysis using the trial classification and prior probabilities as weights. The procedure was applied to several cities, and the results analyzed by correlation analysis from a field sample of building materials. The methodology developed for stratification of a cityscape using multiple variables has application to many other types of environmental studies, including forest inventory, hydrologic unit management, waste disposal, transportation studies, and other urban studies. Multivariate analysis techniques have recently been used for urban stratification in England. ?? 1987 Annals of Regional Science.

Catholic social teaching: Precepts for healthcare reform

PubMed Central

Condit, Donald P.

2016-01-01

The Patient Protection and Affordable Health Care Act of 2010 accelerated bureaucratic appropriation of health care in the United States. Persuaded by laudable intentions of expanded access to care for millions of uninsured Americans, healthcare cost control, and improved medical quality, supporters are now confronted by the unintended consequences of greater government control of health care. The four primary principles of Catholic social teaching guide a best response to our neighbor's healthcare needs. The presence of these principles in the founding documents of the United States facilitates advocacy the public square. Lay summary: Catholic social teaching presents a Magisterial gift to each generation to help build a just society. The four principles, Human Dignity, Common Good, Solidarity, and Subsidiarity, can guide reform of a healthcare system in crisis. These precepts, clearly present in the United States founding documents, and persuasive in the public square, serve as a foundation upon which to improve the medical care of the sick and injured. PMID:28392586

Land-Use Requirements for Solar Power Plants in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ong, S.; Campbell, C.; Denholm, P.

2013-06-01

This report provides data and analysis of the land use associated with utility-scale ground-mounted solar facilities, defined as installations greater than 1 MW. We begin by discussing standard land-use metrics as established in the life-cycle assessment literature and then discuss their applicability to solar power plants. We present total and direct land-use results for various solar technologies and system configurations, on both a capacity and an electricity-generation basis. The total area corresponds to all land enclosed by the site boundary. The direct area comprises land directly occupied by solar arrays, access roads, substations, service buildings, and other infrastructure. As ofmore » the third quarter of 2012, the solar projects we analyze represent 72% of installed and under-construction utility-scale PV and CSP capacity in the United States.« less

Optimal PGU operation strategy in CHP systems

NASA Astrophysics Data System (ADS)

Yun, Kyungtae

Traditional power plants only utilize about 30 percent of the primary energy that they consume, and the rest of the energy is usually wasted in the process of generating or transmitting electricity. On-site and near-site power generation has been considered by business, labor, and environmental groups to improve the efficiency and the reliability of power generation. Combined heat and power (CHP) systems are a promising alternative to traditional power plants because of the high efficiency and low CO2 emission achieved by recovering waste thermal energy produced during power generation. A CHP operational algorithm designed to optimize operational costs must be relatively simple to implement in practice such as to minimize the computational requirements from the hardware to be installed. This dissertation focuses on the following aspects pertaining the design of a practical CHP operational algorithm designed to minimize the operational costs: (a) real-time CHP operational strategy using a hierarchical optimization algorithm; (b) analytic solutions for cost-optimal power generation unit operation in CHP Systems; (c) modeling of reciprocating internal combustion engines for power generation and heat recovery; (d) an easy to implement, effective, and reliable hourly building load prediction algorithm.

Interior view of ground floor unit at west end of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view of ground floor unit at west end of Building No. 23, looking from hallway into second bedroom. Looking south - Easter Hill Village, Building No. 23, North side of South Twenty-sixth Street, east of Corto Square, Richmond, Contra Costa County, CA

Interior view of ground floor unit at west end of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view of ground floor unit at west end of Building No. 23, looking from hallway into first bedroom. Looking south - Easter Hill Village, Building No. 23, North side of South Twenty-sixth Street, east of Corto Square, Richmond, Contra Costa County, CA

Interior view of ground floor unit at west end of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view of ground floor unit at west end of Building No. 23, looking from hallway into bathroom. Looking northwest - Easter Hill Village, Building No. 23, North side of South Twenty-sixth Street, east of Corto Square, Richmond, Contra Costa County, CA

Automatic building information model query generation

DOE PAGES

Jiang, Yufei; Yu, Nan; Ming, Jiang; ...

2015-12-01

Energy efficient building design and construction calls for extensive collaboration between different subfields of the Architecture, Engineering and Construction (AEC) community. Performing building design and construction engineering raises challenges on data integration and software interoperability. Using Building Information Modeling (BIM) data hub to host and integrate building models is a promising solution to address those challenges, which can ease building design information management. However, the partial model query mechanism of current BIM data hub collaboration model has several limitations, which prevents designers and engineers to take advantage of BIM. To address this problem, we propose a general and effective approachmore » to generate query code based on a Model View Definition (MVD). This approach is demonstrated through a software prototype called QueryGenerator. In conclusion, by demonstrating a case study using multi-zone air flow analysis, we show how our approach and tool can help domain experts to use BIM to drive building design with less labour and lower overhead cost.« less

Automatic building information model query generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Yufei; Yu, Nan; Ming, Jiang

Energy efficient building design and construction calls for extensive collaboration between different subfields of the Architecture, Engineering and Construction (AEC) community. Performing building design and construction engineering raises challenges on data integration and software interoperability. Using Building Information Modeling (BIM) data hub to host and integrate building models is a promising solution to address those challenges, which can ease building design information management. However, the partial model query mechanism of current BIM data hub collaboration model has several limitations, which prevents designers and engineers to take advantage of BIM. To address this problem, we propose a general and effective approachmore » to generate query code based on a Model View Definition (MVD). This approach is demonstrated through a software prototype called QueryGenerator. In conclusion, by demonstrating a case study using multi-zone air flow analysis, we show how our approach and tool can help domain experts to use BIM to drive building design with less labour and lower overhead cost.« less

Coordinating with Humans by Adjustable-Autonomy for Multirobot Pursuit (CHAMP)

NASA Astrophysics Data System (ADS)

Dumond, Danielle; Ayers, Jeanine; Schurr, Nathan; Carlin, Alan; Burke, Dustin; Rousseau, Jeffrey

2012-06-01

One of the primary challenges facing the modern small-unit tactical team is the ability of the unit to safely and effectively search, explore, clear and hold urbanized terrain that includes buildings, streets, and subterranean dwellings. Buildings provide cover and concealment to an enemy and restrict the movement of forces while diminishing their ability to engage the adversary. The use of robots has significant potential to reduce the risk to tactical teams and dramatically force multiply the small unit's footprint. Despite advances in robotic mobility, sensing capabilities, and human-robot interaction, the use of robots in room clearing operations remains nascent. CHAMP is a software system in development that integrates with a team of robotic platforms to enable them to coordinate with a human operator performing a search and pursuit task. In this way, the human operator can either give control to the robots to search autonomously, or can retain control and direct the robots where needed. CHAMP's autonomy is built upon a combination of adversarial pursuit algorithms and dynamic function allocation strategies that maximize the team's resources. Multi-modal interaction with CHAMP is achieved using novel gesture-recognition based capabilities to reduce the need for heads-down tele-operation. The Champ Coordination Algorithm addresses dynamic and limited team sizes, generates a novel map of the area, and takes into account mission goals, user preferences and team roles. In this paper we show results from preliminary simulated experiments and find that the CHAMP system performs faster than traditional search and pursuit algorithms.

Ventilation and infiltration in high-rise apartment buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diamond, R.C.; Feustel, H.E.; Dickerhoff, D.J.

1996-03-01

Air flow, air leakage measurements and numerical simulations were made on a 13-story apartment building to characterize the ventilation rates for the individual apartments. Parametric simulations were performed for specific conditions, e.g., height, orientation, outside temperature and wind speed. Our analysis of the air flow simulations suggest that the ventilation to the individual units varies considerably. With the mechanical ventilation system disabled and no wind, units at the lower level of the building have adequate ventilation only on days with high temperature differences, while units on higher floors have no ventilation at all. Units facing the windward side will bemore » over-ventilated when the building experiences wind directions between west and north. At the same time, leeward apartments did not experience any fresh air-because, in these cases, air flows enter the apartments from the corridor and exit through the exhaust shafts and the cracks in the facade. Even with the mechanical ventilation system operating, we found wide variation in the air flows to the individual apartments. In addition to the specific case presented here, these findings have more general implications for energy retrofits and health and comfort of occupants in high-rise apartment buildings.« less

Breath Figure Method for Construction of Honeycomb Films

PubMed Central

Dou, Yingying; Jin, Mingliang; Zhou, Guofu; Shui, Lingling

2015-01-01

Honeycomb films with various building units, showing potential applications in biological, medical, physicochemical, photoelectric, and many other areas, could be prepared by the breath figure method. The ordered hexagonal structures formed by the breath figure process are related to the building units, solvents, substrates, temperature, humidity, air flow, and other factors. Therefore, by adjusting these factors, the honeycomb structures could be tuned properly. In this review, we summarized the development of the breath figure method of fabricating honeycomb films and the factors of adjusting honeycomb structures. The organic-inorganic hybrid was taken as the example building unit to discuss the preparation, mechanism, properties, and applications of the honeycomb films. PMID:26343734

Model-Driven Energy Intelligence

DTIC Science & Technology

2015-03-01

building information model ( BIM ) for operations...estimate of the potential impact on energy performance at Fort Jackson. 15. SUBJECT TERMS Building Information Modeling ( BIM ), Energy, ECMs, monitoring...dimensional AHU Air Handling Unit API Application Programming Interface BIM building information model BLCC Building Life Cycle Cost

Building Construction. Competency-Based Education Curriculum.

ERIC Educational Resources Information Center

West Virginia State Vocational Curriculum Lab., Cedar Lakes.

Developed and field-tested over a 2-year period by vocational teachers in West Virginia, this competency-based building construction curriculum contains five units of study: Safety, form carpentry, carpentry, masonry, and plumbing. Each unit is subdivided into several competencies, and for each competency taught the performance objectives,…

Carpentry and Finishing Procedures. Building Maintenance. Module II. Instructor's Guide.

ERIC Educational Resources Information Center

Hawk, Sam; Brunk, Art

This curriculum guide, keyed to the building maintenance competency profile developed by industry and education professionals, provides three units on carpentry and finishing procedures. The first unit, Exterior Carpentry, contains the following lessons: carpentry safety procedures, ladder and scaffolding safety, door installation/repair,…

77 FR 65665 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-30

...: National Institute of Standards and Technology (NIST). Title: Usage of Elevators for Occupant Evacuation... elevators are currently used by occupants of existing multi- story buildings in the United States during... with or in charge of developing emergency procedures for multi-story buildings in the United States...

3. ROADWAY TO THE SOUTH OF BUILDING NO. 1. AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. ROADWAY TO THE SOUTH OF BUILDING NO. 1. AT FAR LEFT IS THE SHADOW OF BUILDING NO. 6 (WAREHOUSE). ALSO VISIBLE AT THE LEFT IS BUILDING NO. 4 (BOILER HOUSE), BUILDING NO. 3 (GATE HOUSE), AND BUILDING NO. 2 (OFFICE BUILDING). IN THE RIGHT FOREGROUND IS BUILDING NO. 10 (ELECTRICAL SERVICES AND SWITCHING STATION). - United Engineering Company Shipyard, 2900 Main Street, Alameda, Alameda County, CA

On the possibility of generation of cold and additional electric energy at thermal power stations

NASA Astrophysics Data System (ADS)

Klimenko, A. V.; Agababov, V. S.; Borisova, P. N.

2017-06-01

A layout of a cogeneration plant for centralized supply of the users with electricity and cold (ECCG plant) is presented. The basic components of the plant are an expander-generator unit (EGU) and a vapor-compression thermotransformer (VCTT). At the natural-gas-pressure-reducing stations, viz., gas-distribution stations and gas-control units, the plant is connected in parallel to a throttler and replaces the latter completely or partially. The plant operates using only the energy of the natural gas flow without burning the gas; therefore, it can be classified as a fuelless installation. The authors compare the thermodynamic efficiencies of a centralized cold supply system based on the proposed plant integrated into the thermal power station scheme and a decentralized cold supply system in which the cold is generated by electrically driven vapor-compression thermotransformers installed on the user's premises. To perform comparative analysis, the exergy efficiency was taken as the criterion since in one of the systems under investigation the electricity and the cold are generated, which are energies of different kinds. It is shown that the thermodynamic efficiency of the power supply using the proposed plant proves to be higher within the entire range of the parameters under consideration. The article presents the results of investigating the impact of the gas heating temperature upstream from the expander on the electric power of the plant, its total cooling capacity, and the cooling capacities of the heat exchangers installed downstream from the EGU and the evaporator of the VCTT. The results of calculations are discussed that show that the cold generated at the gas-control unit of a powerful thermal power station can be used for the centralized supply of the cold to the ventilation and conditioning systems of both the buildings of the power station and the neighboring dwelling houses, schools, and public facilities during the summer season.

STATION BUILDING. United Engineering Company Ltd., Alameda Shipyard, Ship Repair ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

STATION BUILDING. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities. Plan, elevations, sections, details. Austin Willmott Earl, Consulting Engineer, 233 Sansome Street, San Francisco, California. Drawing no. 504. Various scales. January 20, 1945, no revisions. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76, amendments 4 & 5. blueprint - United Engineering Company Shipyard, Electrical Services & Switching Station, 2900 Main Street, Alameda, Alameda County, CA

76 FR 27843 - National Building Safety Month, 2011

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-13

... 8672 of May 9, 2011 National Building Safety Month, 2011 By the President of the United States of... Building Safety Month. I encourage citizens, government agencies, private businesses, nonprofit...

Style grammars for interactive visualization of architecture.

PubMed

Aliaga, Daniel G; Rosen, Paul A; Bekins, Daniel R

2007-01-01

Interactive visualization of architecture provides a way to quickly visualize existing or novel buildings and structures. Such applications require both fast rendering and an effortless input regimen for creating and changing architecture using high-level editing operations that automatically fill in the necessary details. Procedural modeling and synthesis is a powerful paradigm that yields high data amplification and can be coupled with fast-rendering techniques to quickly generate plausible details of a scene without much or any user interaction. Previously, forward generating procedural methods have been proposed where a procedure is explicitly created to generate particular content. In this paper, we present our work in inverse procedural modeling of buildings and describe how to use an extracted repertoire of building grammars to facilitate the visualization and quick modification of architectural structures and buildings. We demonstrate an interactive application where the user draws simple building blocks and, using our system, can automatically complete the building "in the style of" other buildings using view-dependent texture mapping or nonphotorealistic rendering techniques. Our system supports an arbitrary number of building grammars created from user subdivided building models and captured photographs. Using only edit, copy, and paste metaphors, the entire building styles can be altered and transferred from one building to another in a few operations, enhancing the ability to modify an existing architectural structure or to visualize a novel building in the style of the others.

U.S. Department of Energy awards $200 million for next-generation

Science.gov Websites

build a powerful new next-gen supercomputer, Aurora. The press conference took place at Chicago tech Congress and industry at the announcement of DOE's award of $200 million to Argonne in order to build a accelerate to next-generation exascale computing. DOE earlier announced a $325 million investment to build

Simulated Annealing Based Hybrid Forecast for Improving Daily Municipal Solid Waste Generation Prediction

PubMed Central

Song, Jingwei; He, Jiaying; Zhu, Menghua; Tan, Debao; Zhang, Yu; Ye, Song; Shen, Dingtao; Zou, Pengfei

2014-01-01

A simulated annealing (SA) based variable weighted forecast model is proposed to combine and weigh local chaotic model, artificial neural network (ANN), and partial least square support vector machine (PLS-SVM) to build a more accurate forecast model. The hybrid model was built and multistep ahead prediction ability was tested based on daily MSW generation data from Seattle, Washington, the United States. The hybrid forecast model was proved to produce more accurate and reliable results and to degrade less in longer predictions than three individual models. The average one-week step ahead prediction has been raised from 11.21% (chaotic model), 12.93% (ANN), and 12.94% (PLS-SVM) to 9.38%. Five-week average has been raised from 13.02% (chaotic model), 15.69% (ANN), and 15.92% (PLS-SVM) to 11.27%. PMID:25301508

Organisational commitment in nurses: is it dependent on age or education?

PubMed

Jones, April

2015-02-01

In hospitals in the United States, the ratio of nurses to patients is declining, resulting in an increase in workloads for the remaining nurses. Consequently, the level of commitment that these nurses have to their jobs is important. Outside health care, employees from different generations working for a variety of organisations differ in their levels of organisational commitment, but this information has not been available for nurses. This study, carried out in the state of Alabama, looks at whether nurses from different generations differ in their levels of organisational commitment, and also whether there are any differences in organisational commitment between licensed practical nurses (LPNs) and registered nurses (RNs). A questionnaire designed to measure levels of organisational commitment was answered by 145 nurses. The results were analysed for any differences in organisational commitment in nurses from different generations and with different nursing degrees. Nurses from different generations showed the same levels of organisational commitment, but LPNs showed significantly less affective commitment, that is, lower feelings of loyalty to their workplace, than RNs. This information may be useful for hospital administrators and human resource managers in the United States to highlight the value of flexible incentive packages to address the needs of a diverse workforce. For healthcare employers in the UK, the concept that there is an association between nursing qualifications and levels of organisational commitment is critical for building organisational stability and effectiveness, and for nurse recruitment and retention.

An Asymmetric Furan/Thieno[3,2-b]Thiophene Diketopyrrolopyrrole Building Block for Annealing-Free Green-Solvent Processable Organic Thin-Film Transistors.

PubMed

Ding, Shang; Ni, Zhenjie; Hu, Mengxiao; Qiu, Gege; Li, Jie; Ye, Jun; Zhang, Xiaotao; Liu, Feng; Dong, Huanli; Hu, Wenping

2018-06-21

A new asymmetric furan and thieno[3,2-b]thiophene flanked diketopyrrolopyrrole (TTFDPP) building block for conjugated polymers is designed and used to generate a donor-acceptor semiconducting polymer, poly[3-(furan-2-yl)-2,5-bis(2-octyldodecyl)-6-(thieno[3,2-b]thiophen-2-yl)pyrrolo[3,4-c]pyrrole-1,4(2H,5H)-dione-alt-thieno[3,2-b]thiophene] (abbreviated to PTTFDPP-TT), consisting of TTFDPP unit copolymerized with thieno[3,2-b]thiophene comonomer (TT), which is further synthesized. Results demonstrate that PTTFDPP-TT-based thin-film transistors in a bottom-gate bottom-contact device configuration exhibit typical hole-transporting property, with weak temperature dependence for charge carrier mobility from room temperature to 200 °C. In addition, the good solubility of PTTFDPP-TT due to the incorporation of a polar furan unit and an asymmetric conjugated structure makes it able to be solution processed with a less toxic nonchlorinated solvent such as toluene, demonstrating comparable performance with that prepared from chlorinated solution. These results suggest PTTFDPP-TT as a promising organic semiconductor candidate for annealing-free, environmentally benign, and less energy-consuming applications in large-area flexible organic electronic devices. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Modularized construction of general integrated circuits on individual carbon nanotubes.

PubMed

Pei, Tian; Zhang, Panpan; Zhang, Zhiyong; Qiu, Chenguang; Liang, Shibo; Yang, Yingjun; Wang, Sheng; Peng, Lian-Mao

2014-06-11

While constructing general integrated circuits (ICs) with field-effect transistors (FETs) built on individual CNTs is among few viable ways to build ICs with small dimension and high performance that can be compared with that of state-of-the-art Si based ICs, this has not been demonstrated owing to the absence of valid and well-tolerant fabrication method. Here we demonstrate a modularized method for constructing general ICs on individual CNTs with different electric properties. A pass-transistor-logic style 8-transistor (8-T) unit is built, demonstrated as a multifunctional function generator with good tolerance to inhomogeneity in the CNTs used and used as a building block for constructing general ICs. As an example, an 8-bits BUS system that is widely used to transfer data between different systems in a computer is constructed. This is the most complicated IC fabricated on individual CNTs to date, containing 46 FETs built on six individual semiconducting CNTs. The 8-T unit provides a good basis for constructing complex ICs to explore the potential and limits of CNT ICs given the current imperfection in available CNT materials and may also be developed into a universal and efficient way for constructing general ICs on ideal CNT materials in the future.

76 FR 6702 - Private Transfer Fees

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-08

..., green building, walkability, high density building, arts and culture, and community living'' for the... private transfer fees fund the capital reserves of their buildings or communities and help to fund... affordability of units by causing owners to raise building reserves through special assessments, through higher...

Grounds Maintenance Equipment and Procedures. Building Maintenance. Module VI. Instructor's Guide.

ERIC Educational Resources Information Center

Crank, Virgil

This curriculum guide, one of six modules keyed to the building maintenance competency profile developed by industry and education professionals, provides materials for two units on grounds maintenance equipment and procedures. The first unit deals with grounds maintenance equipment and includes the following lessons: safety; changing oil/filter…

Unit 5, STA. 50+00+RB, retaining wall at Orner Building & ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Unit 5, STA. 50+00+RB, retaining wall at Orner Building & First U.M. Church Rectory-detail - Johnstown Local Flood Protection Project, Beginning on Conemaugh River approx 3.8 miles downstream from confluence of Little Conemaugh & Stony Creek Rivers at Johnstown, Johnstown, Cambria County, PA

Unit 5, STA. 50+00+RB, Orner Building, First U.M. Church Rectory, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Unit 5, STA. 50+00+RB, Orner Building, First U.M. Church Rectory, & First U.M. Church-context - Johnstown Local Flood Protection Project, Beginning on Conemaugh River approx 3.8 miles downstream from confluence of Little Conemaugh & Stony Creek Rivers at Johnstown, Johnstown, Cambria County, PA

Preservation Building Survey Form for Freestanding Library Unit.

ERIC Educational Resources Information Center

Huff, Susan M.

A modification of a University of Michigan form, this survey form is designed to obtain information on a freestanding library unit for preservation. The questionnaire covers the following areas: (1) library facility construction--e.g., primary building materials, characteristics of the foundation and roof, recent problems; (2) heating and cooling…

Electrical Procedures and Environmental Control Systems. Building Maintenance. Module IV. Instructor's Guide.

ERIC Educational Resources Information Center

Sloan, Garry

This curriculum guide, one of six modules keyed to the building maintenance competency profile developed by industry and education professionals, provides materials for two units on electrical procedures and environmental control systems. Unit 1, on electrical procedures, includes the following lessons: electrical safety; troubleshooting and…

19 CFR 10.602 - Packing materials and containers for shipment.

Code of Federal Regulations, 2010 CFR

2010-04-01

...-Central America-United States Free Trade Agreement Rules of Origin § 10.602 Packing materials and....602 Section 10.602 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY... into the United States. Accordingly, in applying the build-down, build-up, or net cost method for...

The United States President's Emergency Plan for AIDS Relief: a story of partnerships and smart investments to turn the tide of the global AIDS pandemic.

PubMed

Goosby, Eric; Dybul, Mark; Fauci, Anthony S; Fauci, Anthony A; Fu, Joe; Walsh, Thomas; Needle, Richard; Bouey, Paul

2012-08-15

The United States President's Emergency Plan for AIDS Relief (PEPFAR) has played a key leadership role in the global response to the HIV/AIDS pandemic. PEPFAR was inspired by the principles of the historic Monterrey Consensus (United Nations. Monterrey Consensus on Financing for Development, Monterrey, Mexico, March 18-22, 2002. New York: United Nations; 2002. Available at: http://www.un.org/esa/ffd/monterrey/MonterreyConsensus.pdf. Accessed April 21, 2012), which changed the underlying conceptual framework for international development, and therefore global health--a shift from paternalism to partnership that begins with country ownership and requires good governance, a results-based approach, and engagement of all sectors of society. PEPFAR began with a focus on the growing emergency of the HIV/AIDS pandemic by rapidly expanding HIV services, building clinical capacity, implementing strategic information systems, and building a coalition of partners to lead the response. Within the first years of implementation, there was a shift to sustainability, including the advent of Partnership Frameworks. The PEPFAR reauthorization in 2008 codified into law, the evolution in policies and programs for the next phase of implementation. In 2011 alone, PEPFAR supported nearly 4 million people on treatment, supported programs that provided more than 1.5 million HIV-positive pregnant women with antiretroviral drugs to prevent HIV transmission to their children, and supported HIV testing for more than 40 million people. This article provides an overview of how smart investments and partnerships across sectors and US agencies have helped achieve unprecedented results in increasing HIV/AIDS services and engaging partner countries and organizations in sharing the responsibility for an AIDS-free generation.

Biorational control programme for the German cockroach (Blattaria: Blattellidae) in selected urban communities.

PubMed

Shahraki, GholamHossein; Bin Ibrahim, Yusof; Noor, Hafidzi Mohd; Rafinejad, Javad; Shahar, Mohd Khadri

2010-08-01

This study assessed the effectiveness of a biorational control approach using 2% hydramethylnon gel bait on German cockroaches, Blattella germanica (L.) in some residential and hospital buildings in South Western Iran. In total, three buildings consisting of 150 apartment units and 101 hospital units were monitored weekly via sticky trap for German cockroach infestations over a period of eight months. These infested units were randomly subjected to intervention and control treatments. Pamphlets and posters were provided and lectures were given to support the educational programmes as a tactic of the biorational system. Survey on cockroach index for intervention units showed 67-94% recovery to achieve clean level of infestation for intervention units of the residential buildings and 83% for the hospital. Mean percentage reductions for treatment groups throughout the 15-week treatment period were 76.8% for the residential buildings and 88.1% for the hospital, showing significant differences compared to the control groups. Linear regression of infestation rates were recorded weekly after treatment and their negative slope for treatment groups substantiated significant reductions for interventions. The results of this study showed that biorational control method, using gel bait, educational programmes and sanitation, is an effective way to manage German cockroach infestation.

STTR Phase I: Low-Cost, High-Accuracy, Whole-Building Carbon Dioxide Monitoring for Demand Control Ventilation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hallstrom, Jason O.; Ni, Zheng Richard

This STTR Phase I project assessed the feasibility of a new CO 2 sensing system optimized for low-cost, high-accuracy, whole-building monitoring for use in demand control ventilation. The focus was on the development of a wireless networking platform and associated firmware to provide signal conditioning and conversion, fault- and disruptiontolerant networking, and multi-hop routing at building scales to avoid wiring costs. Early exploration of a bridge (or “gateway”) to direct digital control services was also explored. Results of the project contributed to an improved understanding of a new electrochemical sensor for monitoring indoor CO 2 concentrations, as well as themore » electronics and networking infrastructure required to deploy those sensors at building scales. New knowledge was acquired concerning the sensor’s accuracy, environmental response, and failure modes, and the acquisition electronics required to achieve accuracy over a wide range of CO 2 concentrations. The project demonstrated that the new sensor offers repeatable correspondence with commercial optical sensors, with supporting electronics that offer gain accuracy within 0.5%, and acquisition accuracy within 1.5% across three orders of magnitude variation in generated current. Considering production, installation, and maintenance costs, the technology presents a foundation for achieving whole-building CO 2 sensing at a price point below $0.066 / sq-ft – meeting economic feasibility criteria established by the Department of Energy. The technology developed under this award addresses obstacles on the critical path to enabling whole-building CO 2 sensing and demand control ventilation in commercial retrofits, small commercial buildings, residential complexes, and other highpotential structures that have been slow to adopt these technologies. It presents an opportunity to significantly reduce energy use throughout the United States.« less

2. Detail of panel in generator room, building 501, looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Detail of panel in generator room, building 501, looking north - Offutt Air Force Base, Strategic Air Command Headquarters & Command Center, Command Center, 901 SAC Boulevard, Bellevue, Sarpy County, NE

Compensation for Distributed Solar. A Survey of Options to Preserve Stakeholder Value

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flores-Espino, Francisco

2015-09-01

Compensation mechanisms for electricity generation systems installed behind the meter are under scrutiny in several jurisdictions in the United States. Legislators in 29 states introduced bills to amend net metering provisions in 2014, and in 33 states in the 2015 legislative session as of August 20, 2015. Some utilities have also sought to increase the revenue they receive from net-metered customers through rate redesign. The circumstances that have triggered the recent push for change include a growing percentage of net-metered customers, potential effects of distributed generation on cost allocation, decreasing photovoltaic (PV) system costs, the challenges of integrating high levelsmore » of solar generation in the distribution network, and increasing pressure on utility business models. This report presents a survey of options to charge and compensate PV customers, as well as options that may preserve utility revenues in scenarios with increased DG. These options could be used as building blocks to create a distributed generation (DG) compensation policy that may preserve the value of the different stakeholders and balance their interests.« less

6. A VIEW TOWARD THE EAST SIDE OF BUILDING NO. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. A VIEW TOWARD THE EAST SIDE OF BUILDING NO. 1, SHOWING THE OFFICE SECTION AT THE SOUTHEAST CORNER. BUILDING NO. 18 (ENGINEERING BUILDING) IS VISIBLE IN THE CENTER DISTANCE, AND BUILDING NO. 12 (OFFICE/SUBSTATION) AT THE RIGHT. - United Engineering Company Shipyard, 2900 Main Street, Alameda, Alameda County, CA

Modeling language and cognition with deep unsupervised learning: a tutorial overview

PubMed Central

Zorzi, Marco; Testolin, Alberto; Stoianov, Ivilin P.

2013-01-01

Deep unsupervised learning in stochastic recurrent neural networks with many layers of hidden units is a recent breakthrough in neural computation research. These networks build a hierarchy of progressively more complex distributed representations of the sensory data by fitting a hierarchical generative model. In this article we discuss the theoretical foundations of this approach and we review key issues related to training, testing and analysis of deep networks for modeling language and cognitive processing. The classic letter and word perception problem of McClelland and Rumelhart (1981) is used as a tutorial example to illustrate how structured and abstract representations may emerge from deep generative learning. We argue that the focus on deep architectures and generative (rather than discriminative) learning represents a crucial step forward for the connectionist modeling enterprise, because it offers a more plausible model of cortical learning as well as a way to bridge the gap between emergentist connectionist models and structured Bayesian models of cognition. PMID:23970869

Modeling language and cognition with deep unsupervised learning: a tutorial overview.

PubMed

Zorzi, Marco; Testolin, Alberto; Stoianov, Ivilin P

2013-01-01

Deep unsupervised learning in stochastic recurrent neural networks with many layers of hidden units is a recent breakthrough in neural computation research. These networks build a hierarchy of progressively more complex distributed representations of the sensory data by fitting a hierarchical generative model. In this article we discuss the theoretical foundations of this approach and we review key issues related to training, testing and analysis of deep networks for modeling language and cognitive processing. The classic letter and word perception problem of McClelland and Rumelhart (1981) is used as a tutorial example to illustrate how structured and abstract representations may emerge from deep generative learning. We argue that the focus on deep architectures and generative (rather than discriminative) learning represents a crucial step forward for the connectionist modeling enterprise, because it offers a more plausible model of cortical learning as well as a way to bridge the gap between emergentist connectionist models and structured Bayesian models of cognition.

A monolithically integrated polarization entangled photon pair source on a silicon chip

PubMed Central

Matsuda, Nobuyuki; Le Jeannic, Hanna; Fukuda, Hiroshi; Tsuchizawa, Tai; Munro, William John; Shimizu, Kaoru; Yamada, Koji; Tokura, Yasuhiro; Takesue, Hiroki

2012-01-01

Integrated photonic circuits are one of the most promising platforms for large-scale photonic quantum information systems due to their small physical size and stable interferometers with near-perfect lateral-mode overlaps. Since many quantum information protocols are based on qubits defined by the polarization of photons, we must develop integrated building blocks to generate, manipulate, and measure the polarization-encoded quantum state on a chip. The generation unit is particularly important. Here we show the first integrated polarization-entangled photon pair source on a chip. We have implemented the source as a simple and stable silicon-on-insulator photonic circuit that generates an entangled state with 91 ± 2% fidelity. The source is equipped with versatile interfaces for silica-on-silicon or other types of waveguide platforms that accommodate the polarization manipulation and projection devices as well as pump light sources. Therefore, we are ready for the full-scale implementation of photonic quantum information systems on a chip. PMID:23150781

Modeling carbon dioxide emissions reductions for three commercial reference buildings in Salt Lake City

NASA Astrophysics Data System (ADS)

Lucich, Stephen M.

In the United States, the buildings sector is responsible for approximately 40% of the national carbon dioxide (CO2) emissions. CO2 is created during the generation of heat and electricity, and has been linked to climate change, acid rain, a variety of health threats, surface water depletion, and the destruction of natural habitats. Building energy modeling is a powerful educational tool that building owners, architects, engineers, city planners, and policy makers can use to make informed decisions. The aim of this thesis is to simulate the reduction in CO2 emissions that may be achieved for three commercial buildings located in Salt Lake City, UT. The following two questions were used to guide this process: 1. How much can a building's annual CO2 emissions be reduced through a specific energy efficiency upgrade or policy? 2. How much can a building's annual CO2 emissions be reduced through the addition of a photovoltaic (PV) array? How large should the array be? Building energy simulations were performed with the Department of Energy's EnergyPlus software, commercial reference building models, and TMY3 weather data. The chosen models were a medium office building, a primary school, and a supermarket. Baseline energy consumption data were simulated for each model in order to identify changes that would have a meaningful impact. Modifications to the buildings construction and operation were considered before a PV array was incorporated. These modifications include (1) an improved building envelope, (2) reduced lighting intensity, and (3) modified HVAC temperature set points. The PV array sizing was optimized using a demand matching approach based on the method of least squares. The arrays tilt angle was optimized using the golden section search algorithm. Combined, energy efficiency upgrades and the PV array reduced building CO2 emissions by 58.6, 54.0, and 52.2% for the medium office, primary school, and supermarket, respectively. However, for these models, it was determined that the addition of a PV array is not feasible from a purely economic viewpoint. Several avenues for expansion of this research are presented in Chapter 5.

First experiences with methods to measure ammonia emissions from naturally ventilated cattle buildings in the U.K.

NASA Astrophysics Data System (ADS)

Demmers, T. G. M.; Burgess, L. R.; Short, J. L.; Phillips, V. R.; Clark, J. A.; Wathes, C. M.

A method has been developed to measure the emission rate of ammonia from naturally ventilated U.K. livestock buildings. The method is based on measurements of ammonia concentration and estimates of the ventilation rate of the building by continuous release of carbon monoxide tracer within the building. The tracer concentration is measured at nine positions in openings around the perimeter of the building, as well as around a ring sampling line. Two criteria were evaluated to decide whether, at any given time, a given opening in the building acted as an air inlet or as an air outlet. Carbon monoxide concentration difference across an opening was found to be a better criterion than the temperature difference across the opening. Ammonia concentrations were measured continuously at the sampling points using a chemiluminescence analyser. The method was applied to a straw-bedded beef unit and to a slurry-based dairy unit. Both buildings were of space-boarded construction. Ventilation rates estimated by the ring line sample were consistently higher than by the perimeter samples. During calm weather, the ventilation estimates by both samples were similar (10-20 air changes h -1). However, during windy conditions (>5 m s -1) the ventilation rate was overestimated by the ring line sample (average 100 air changes h -1) compared to the perimeter samples (average 50 air changes h -1). The difference was caused by incomplete mixing of the tracer within the building. The ventilation rate estimated from the perimeter samples was used for the calculation of the emission rate. Preliminary estimates of the ammonia emission factor were 6.0 kg NH 3 (500 kg live-weight) -1 (190 d) -1 for the slurry-based dairy unit and 3.7 for the straw-bedded beef unit.

Predictive model for CO2 generation and decay in building envelopes

NASA Astrophysics Data System (ADS)

Aglan, Heshmat A.

2003-01-01

Understanding carbon dioxide generation and decay patterns in buildings with high occupancy levels is useful to identify their indoor air quality, air change rates, percent fresh air makeup, occupancy pattern, and how a variable air volume system to off-set undesirable CO2 level can be modulated. A mathematical model governing the generation and decay of CO2 in building envelopes with forced ventilation due to high occupancy is developed. The model has been verified experimentally in a newly constructed energy efficient healthy house. It was shown that the model accurately predicts the CO2 concentration at any time during the generation and decay processes.

The National Building Museum.

ERIC Educational Resources Information Center

Fitzpatrick, Sandra; Lowry, Bates

1984-01-01

The major goal of the National Building Museum (Washington, DC) is to develop a more enlightened citizenry through information and communication about buildings in the United States. Specific activities of the museum are described. (RM)

Thermal-envelope field measurements in an energy-efficient office/dormitory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christian, J.E.

1982-01-01

A 345 m/sup 2/ earth-covered structure located at the Oak Ridge National Laboratory is the focus of a DOE sponsored building-envelope research project. To heat the office/dormitory building over the 1981-1982 heating season would cost $1.70/m/sup 2/ ($0.16/ft/sup 2/), assuming $0.07/kWh. The thermal-integrity factor is 0.016 kWh/m/sup 2/ /sup 0/C (2.8 Btu/ft/sup 2/ /sup 0/F). A preliminary DOE-II model estimates the monthly electric energy needs for heating within 5% of field data derived estimates. DOE-II building simulations suggest that this earth-covered/passively heated office dormitory saves 30% for space heating and 26% for cooling compared to an energy efficient above grademore » structure. A preliminary winter energy balance has been generated from data collected in February and March providing a fractional breakdown of thermal losses and gains. A number of the energy-conserving component performances have been isolated; earth-covered roof, bermed wall, and nonvented trombe wall. The earth-covered roof system showed an overall thermal transmittance of 0.18 W/m/sup 2///sup 0/C (R=31 hr ft/sup 2/ /sup 0/F/Btu). The thermocouple wells located in the earth surrounding the building indicate the additional energy savings of burying over berming. For one week in February the trombe wall produced a 50% greater net thermal gain to the building then south facing windows per equivalent unit area.« less

Standardized Curriculum for Building Trades.

ERIC Educational Resources Information Center

Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

Standardized curricula are provided for two courses for the secondary vocational education program in Mississippi: building trades I and II. The eight units in building trades I are as follows: safety; measurement; tools, equipment, and hardware; building plans and blueprints; introduction to carpentry; introduction to plumbing; introduction to…

38 CFR 39.21 - Space criteria for support facilities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... building. The administrative building should be approximately 1,600 NSF in total, providing space, as... room; (6) Military honors team; (7) Refreshment unit; (8) Housekeeping aide's closet; and (9) Restroom facilities. (b) Maintenance/service building. The maintenance/service building may be combined with the...

Understanding the Uncertainties in Consequences of Climate Change for the United States Power Sector Infrastructure when Considering a Realistic Mitigation Pace and Adaptation Needs.

NASA Astrophysics Data System (ADS)

Anderson, N. J.; Whiteford, E. J.; Jones, V.; Fritz, S. C.; Yang, H.; Appleby, P.; Bindler, R.

2014-12-01

In order to overcome the potential damages associated with climate change, a massive reduction in greenhouse gas emissions is necessary. Achieving these levels of emissions reductions will require dramatic changes in the U.S. electricity generating infrastructure: almost all of the fossil-generation fleet will need to be replaced with low-carbon sources and society would have to maintain a high build rate of new capacity for decades. Because the build rate of new electricity generating capacity may be limited, the timing of regulation is critical—the longer the U.S. waits to start reducing emissions, the faster the turnover in the electricity sector must occur in order to meet the same target. We investigate the relationship between climate policy timing and infrastructure turnover in the electricity sector. How long can we wait before constraints on infrastructure turnover in the electricity sector make achieving our climate goals impossible? We show that delaying climate change policy increases average construction rates by 25% to 85% and increases maximum construction rates by 50% to 300%. We also show that delaying climate policy has little effect on the age of retired plants or the stranded costs associated with premature retirement. We show that as we delay policy action, some goals won't be possible for attain. For example, unless we enable emissions reductions today, reducing cumulative emissions between now and 2040 by 50% when compared to a no-policy scenario is not possible.

Increasing chronic disease research capacity in Guatemala through a mentoring program.

PubMed

Barnoya, Joaquin; Monzon, Jose C; Colditz, Graham A

2013-09-12

The Chronic Disease Research Fellowship Program (RFP) aims to build the research capacity of recent medical graduates to support the development of chronic disease control strategies. Guatemala is undergoing an epidemiologic transition. However, given the way universities and the health care system are structured, it lacks an environment that fosters research careers and generates the required knowledge to implement sound public health policies and clinical strategies. The RFP was implemented at the Cardiovascular Unit of Guatemala. This 4-year Program recruited two one-year fellows and provided funding to define a research topic, write a protocol and implement the research. Strong emphasis is placed on developing skills in knowledge translation and exchange to bridge the "know-do" gap. Close mentoring relationships between the Principal Investigator and former and current fellows are fostered through the Program. The mentoring Program has generated strategic data to support the implementation of sound chronic disease control strategies, mainly related to tobacco control. Results have been presented nationally and internationally. Research training has included principles of biostatistics and epidemiology, and a journal club. The Program is increasingly generating interest among medical graduates to pursue further research training abroad and is building local research capacity. Fellows and research assistants have created a research network in Guatemala and abroad. The main obstacle the Program faces is ensuring long-term sustainability. A mentoring program can lead to an increase in research interest and capacity in a low-income country with little research infrastructure.

Impacts of Commercial Building Controls on Energy Savings and Peak Load Reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fernandez, Nicholas E.P.; Katipamula, Srinivas; Wang, Weimin

Commercial buildings in the United States use about 18 Quadrillion British thermal units (Quads) of primary energy annually . Studies have shown that as much as 30% of building energy consumption can be avoided by using more accurate sensing, using existing controls better, and deploying advanced controls; hence, the motivation for the work described in this report. Studies also have shown that 10% to 20% of the commercial building peak load can be temporarily managed/curtailed to provide grid services. Although many studies have indicated significant potential for reducing the energy consumption in commercial buildings, very few have documented the actualmore » savings. The studies that did so only provided savings at the whole building level, which makes it difficult to assess the savings potential of each individual measure deployed.« less

TLS for generating multi-LOD of 3D building model

NASA Astrophysics Data System (ADS)

Akmalia, R.; Setan, H.; Majid, Z.; Suwardhi, D.; Chong, A.

2014-02-01

The popularity of Terrestrial Laser Scanners (TLS) to capture three dimensional (3D) objects has been used widely for various applications. Development in 3D models has also led people to visualize the environment in 3D. Visualization of objects in a city environment in 3D can be useful for many applications. However, different applications require different kind of 3D models. Since a building is an important object, CityGML has defined a standard for 3D building models at four different levels of detail (LOD). In this research, the advantages of TLS for capturing buildings and the modelling process of the point cloud can be explored. TLS will be used to capture all the building details to generate multi-LOD. This task, in previous works, involves usually the integration of several sensors. However, in this research, point cloud from TLS will be processed to generate the LOD3 model. LOD2 and LOD1 will then be generalized from the resulting LOD3 model. Result from this research is a guiding process to generate the multi-LOD of 3D building starting from LOD3 using TLS. Lastly, the visualization for multi-LOD model will also be shown.

The medicalization of obesity, bariatric surgery, and population health.

PubMed

Ortiz, Selena E; Kawachi, Ichiro; Boyce, Angie M

2017-09-01

This article examines how the medicalization of obesity validates the use of bariatric surgery to treat obesity in the United States and how expansions in access to bariatric surgery normalize surgical procedures as disease treatment and prevention tools. Building on this discussion, the article poses two questions for population health regarding health technology: (1) to what extent does bariatric surgery treat obesity in the United States while diverting attention away from the ultimate drivers of the epidemic and (2) to what extent does bariatric surgery improve outcomes for some groups in the US population while simultaneously generating disparities? We conduct a brief, historical analysis of the American Medical Association's decision to reclassify obesity as a disease through internal documents, peer-reviewed expert reports, and major media coverage. We use medicalization theory to show how this decision by the American Medical Association channels increased focus on obesity into the realm of medical intervention, particularly bariatric surgery, and use this evidence to review research trends on bariatric surgery. We propose research questions that investigate the population health dimensions of bariatric surgery in the United States and note key areas of future research. Our objective is to generate a discourse that considers bariatric surgery beyond the medical realm to better understand how technological interventions might work collectively with population-level obesity prevention efforts and how, in turn, population health approaches may improve bariatric surgery outcomes.

Effects of ceiling-mounted HEPA-UV air filters on airborne bacteria concentrations in an indoor therapy pool building.

PubMed

Kujundzic, Elmira; Zander, David A; Hernandez, Mark; Angenent, Largus T; Henderson, David E; Miller, Shelly L

2005-02-01

The purpose of this study was to assess the effectiveness of a new generation of high-volume, ceiling-mounted high-efficiency particulate air (HEPA)-ultraviolet (UV) air filters (HUVAFs) for their ability to remove or inactivate bacterial aerosol. In an environmentally controlled full-scale laboratory chamber (87 m3), and an indoor therapy pool building, the mitigation ability of air filters was assessed by comparing concentrations of total bacteria, culturable bacteria, and airborne endotoxin with and without the air filters operating under otherwise similar conditions. Controlled chamber tests with pure cultures of aerosolized Mycobacterium parafortuitum cells showed that the HUVAF unit tested provided an equivalent air-exchange rate of 11 hr(-1). Using this equivalent air-exchange rate as a design basis, three HUVAFs were installed in an indoor therapy pool building for bioaerosol mitigation, and their effectiveness was studied over a 2-year period. The HUVAFs reduced concentrations of culturable bacteria by 69 and 80% during monitoring periods executed in respective years. The HUVAFs reduced concentrations of total bacteria by 12 and 76% during the same monitoring period, respectively. Airborne endotoxin concentrations were not affected by the HUVAF operation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaplanis, S., E-mail: kaplanis@teipat.gr; Kaplani, E.

The paper presents the design features, the energy modelling and optical performance details of two pilot Intelligent Energy Buildings, (IEB). Both are evolution of the Zero Energy Building (ZEB) concept. RES innovations backed up by signal processing, simulation models and ICT tools were embedded into the building structures in order to implement a new predictive energy management concept. In addition, nano-coatings, produced by TiO2 and ITO nano-particles, were deposited on the IEB structural elements and especially on the window panes and the PV glass covers. They exhibited promising SSP values which lowered the cooling loads and increased the PV modulesmore » yield. Both pilot IEB units were equipped with an on-line dynamic hourly solar radiation prediction model, implemented by sensors and the related software to manage effectively the energy source, the loads and the storage or the backup system. The IEB energy sources covered the thermal loads via a south façade embedded in the wall and a solar roof which consists of a specially designed solar collector type, while a PV generator is part of the solar roof, like a compact BIPV in hybrid configuration to a small wind turbine.« less

Efforts of the occupant to change physical quality of residential unit through the change of building material at low cost flats in Jakarta

NASA Astrophysics Data System (ADS)

Nurdiani, N.

2018-03-01

Low cost flats in Jakarta – Indonesia is provided by the government for low-income people in urban areas, in line with the program to redevelop or renew slum areas. Low cost flat is built with the minimum standard of building materials. The purpose of this study is to know efforts of the occupants to change of building materials at residential unit of low cost flats. The research was conducted by descriptive method at four of low cost housing in Jakarta: Rusuna Bendungan Hilir 1, Rusuna Tambora IIIA, Rusuna Bidara Cina, and Rusuna Sukapura. The results showed that physical changes which happened in low cost flats are aesthetic (residence paint color change), or improvement of physical quality of residential unit (change of building material), become dominant aspects done by residents in four rusuna.

Energy performance evaluation of AAC

NASA Astrophysics Data System (ADS)

Aybek, Hulya

The U.S. building industry constitutes the largest consumer of energy (i.e., electricity, natural gas, petroleum) in the world. The building sector uses almost 41 percent of the primary energy and approximately 72 percent of the available electricity in the United States. As global energy-generating resources are being depleted at exponential rates, the amount of energy consumed and wasted cannot be ignored. Professionals concerned about the environment have placed a high priority on finding solutions that reduce energy consumption while maintaining occupant comfort. Sustainable design and the judicious combination of building materials comprise one solution to this problem. A future including sustainable energy may result from using energy simulation software to accurately estimate energy consumption and from applying building materials that achieve the potential results derived through simulation analysis. Energy-modeling tools assist professionals with making informed decisions about energy performance during the early planning phases of a design project, such as determining the most advantageous combination of building materials, choosing mechanical systems, and determining building orientation on the site. By implementing energy simulation software to estimate the effect of these factors on the energy consumption of a building, designers can make adjustments to their designs during the design phase when the effect on cost is minimal. The primary objective of this research consisted of identifying a method with which to properly select energy-efficient building materials and involved evaluating the potential of these materials to earn LEED credits when properly applied to a structure. In addition, this objective included establishing a framework that provides suggestions for improvements to currently available simulation software that enhance the viability of the estimates concerning energy efficiency and the achievements of LEED credits. The primary objective was accomplished by using conducting several simulation models to determine the relative energy efficiency of wood-framed, metal-framed, and Aerated Autoclaved Concrete (AAC) wall structures for both commercial and residential buildings.

Contributions of Local Farming to Urban Sustainability in the Northeast United States.

PubMed

Goldstein, Benjamin P; Hauschild, Michael Z; Fernández, John E; Birkved, Morten

2017-07-05

Food consumption is an important contributor to a city's environmental impacts (carbon emissions, land occupation, water use, etc.) Urban farming (UF) has been advocated as a means to increase urban sustainability by reducing food-related transport and tapping into local resources. Taking Boston as an illustrative Northeast U.S. city, we developed a novel method to estimate sub-urban, food-borne carbon and land footprints using multiregion-input-output modeling and nutritional surveys. Computer simulations utilizing primary data explored UF's ability to reduce these footprints using select farming technologies, building on previous city-scale UF assessments which have hitherto been dependent on proxy data for UF. We found that UF generated meagre food-related carbon footprint reductions (1.1-2.9% of baseline 2211 kg CO 2 equivalents/capita/annum) and land occupation increases (<1% of baseline 9000 m 2 land occupation/capita/annum) under optimal production scenarios, informing future evidence-based urban design and policy crafting in the region. Notwithstanding UF's marginal environmental gains, UF could help Boston meet national nutritional guidelines for vegetable intake, generate an estimated $160 million U.S. in revenue to growers and act as a pedagogical and community building tool, though these benefits would hinge on large-scale UF proliferation, likely undergirded by environmental remediation of marginal lands in the city.

Integrating Building Information Modeling and Green Building Certification: The BIM-LEED Application Model Development

ERIC Educational Resources Information Center

Wu, Wei

2010-01-01

Building information modeling (BIM) and green building are currently two major trends in the architecture, engineering and construction (AEC) industry. This research recognizes the market demand for better solutions to achieve green building certification such as LEED in the United States. It proposes a new strategy based on the integration of BIM…

Simplified Floor-Area-Based Energy-Moisture-Economic Model for Residential Buildings

ERIC Educational Resources Information Center

Martinez, Luis A.

2009-01-01

In the United States, 21% of all energy is used in residential buildings (40% of which is for heating and cooling homes). Promising improvements in residential building energy efficiency are underway such as the Building America Program and the Passive House Concept. The ability of improving energy efficiency in buildings is enhanced by building…

24 CFR 901.30 - Indicator #5, annual inspection of units and systems.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the Environmental Protection Agency; (C) Natural disasters; and (D) Units kept vacant because they... buildings and sites according to the PHA's maintenance plan, including performing the required maintenance... weight of x1. (1) Grade A: The PHA inspected all major systems at 100% of its buildings and sites...

Building Trades. Block III. Floor Framing.

ERIC Educational Resources Information Center

Texas A and M Univ., College Station. Vocational Instructional Services.

This document contains three units of a course on floor framing to be used as part of a building trades program. Each unit consists, first, of an informational lesson, with complete lesson plan for the teacher's use. Included in each lesson plan are the lesson aim; lists of teaching aids, materials, references, and prerequisites for students;…

Building Customized University-to-Business (U2B) Partnerships

ERIC Educational Resources Information Center

Irvine, George; Verma, Lisa

2013-01-01

Continuing education (CE) units throughout the United States have successfully built University-to-Business (U2B) partnerships to provide greater value to their community partners and to increase revenue for the university. Our experience in building U2B partnerships and feedback from our partners--businesses, corporations, state agencies, and…

47 CFR 68.105 - Minimum point of entry (MPOE) and demarcation point.

Code of Federal Regulations, 2010 CFR

2010-10-01

... be either the closest practicable point to where the wiring crosses a property line or the closest practicable point to where the wiring enters a multiunit building or buildings. The reasonable and... situations. (c) Single unit installations. For single unit installations existing as of August 13, 1990, and...

A study of interunit dispersion around multistory buildings with single-sided ventilation under different wind directions

NASA Astrophysics Data System (ADS)

Ai, Z. T.; Mak, C. M.

2014-05-01

This study examines the interunit dispersion characteristics in and around multistory buildings under wind-induced single-sided ventilation conditions using computational fluid dynamics (CFD) method, under the hypothesis that infectious respiratory aerosols exhausted from a unit can reenter into another unit in a same building through opened windows. The effect of balconies on the interunit dispersion pattern is considered. The RNG k - ɛ model and the two-layer near-wall model are employed to establish the coupled indoor and outdoor airflow field, and the tracer gas technique is adopted to simulate pollutant dispersion. Reentry ratios from each unit to other units under prevailing wind directions are quantified and the possible interunit dispersion routes are then revealed. It is found that many reentry ratios appear to reach around 10.0%, suggesting that the interunit dispersion is an important pollutant transmission route. The interunit dispersion pattern is highly dependent on the incident wind direction and the fact whether the building has protrusive envelope features. On average, the strongest dispersion occurs on the windward wall of the buildings under oblique wind direction, owing to high ACH (air change per hour) values and unidirectional spread routes. Except under a normal incident wind, the presence of balconies intensifies the interunit dispersion by forming dispersion channels to increase the reentry ratios.

Improving Power System Modeling. A Tool to Link Capacity Expansion and Production Cost Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diakov, Victor; Cole, Wesley; Sullivan, Patrick

2015-11-01

Capacity expansion models (CEM) provide a high-level long-term view at the prospects of the evolving power system. In simulating the possibilities of long-term capacity expansion, it is important to maintain the viability of power system operation in the short-term (daily, hourly and sub-hourly) scales. Production-cost models (PCM) simulate routine power system operation on these shorter time scales using detailed load, transmission and generation fleet data by minimizing production costs and following reliability requirements. When based on CEM 'predictions' about generating unit retirements and buildup, PCM provide more detailed simulation for the short-term system operation and, consequently, may confirm the validitymore » of capacity expansion predictions. Further, production cost model simulations of a system that is based on capacity expansion model solution are 'evolutionary' sound: the generator mix is the result of logical sequence of unit retirement and buildup resulting from policy and incentives. The above has motivated us to bridge CEM with PCM by building a capacity expansion - to - production cost model Linking Tool (CEPCoLT). The Linking Tool is built to onset capacity expansion model prescriptions onto production cost model inputs. NREL's ReEDS and Energy Examplar's PLEXOS are the capacity expansion and the production cost models, respectively. Via the Linking Tool, PLEXOS provides details of operation for the regionally-defined ReEDS scenarios.« less

39 CFR 776.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... UNITED STATES POSTAL SERVICE ENVIRONMENTAL REGULATIONS FLOODPLAIN AND WETLAND PROCEDURES General... buildings, structures and improvements. Contending site means a site or existing building for a proposed... operations organization. Facility means any building, appurtenant structures, or associated infrastructure...

US EPA Base Study Standard Operating Procedure for Building Recruiting

EPA Pesticide Factsheets

Building recruiting for the BASE study is defined by a random selection of buildings within cities of population exceeding 100,000 inhabitants and located in selected climatic regions of the United States.

View from east to west of PAR site storage building; ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View from east to west of PAR site storage building; formerly PAR dispensary - Stanley R. Mickelsen Safeguard Complex, Storage Building, Across street from Family Housing Units 110 & 111, Nekoma, Cavalier County, ND

18. Control Area, Frequency Changer and Generator Building, interior view ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

18. Control Area, Frequency Changer and Generator Building, interior view of remaining control panels VIEW WEST - NIKE Missile Battery PR-79, Control Area, Tucker Hollow Road south of State Route 101, Foster, Providence County, RI

12. LAUNCH CONTROL SUPPORT BUILDING. INTERIOR OF GENERATOR ROOM. VIEW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. LAUNCH CONTROL SUPPORT BUILDING. INTERIOR OF GENERATOR ROOM. VIEW TO EAST. - Minuteman III ICBM Launch Control Facility November-1, 1.5 miles North of New Raymer & State Highway 14, New Raymer, Weld County, CO

Retrofit of a Multifamily Mass Masonry Building in New England

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ueno, K.; Kerrigan, P.; Wytrykowska, H.

2013-08-01

Merrimack Valley Habitat for Humanity (MVHfH) has partnered with Building Science Corporation to provide high performance affordable housing for 10 families in the retrofit of an existing brick building (a former convent) into condominiums. The research performed for this project provides information regarding advanced retrofit packages for multi-family masonry buildings in Cold climates. In particular, this project demonstrates safe, durable, and cost-effective solutions that will potentially benefit millions of multi-family brick buildings throughout the East Coast and Midwest (Cold climates). The retrofit packages provide insight on the opportunities for and constraints on retrofitting multifamily buildings with ambitious energy performance goalsmore » but a limited budget. The condominium conversion project will contribute to several areas of research on enclosures, space conditioning, and water heating. Enclosure items include insulation of mass masonry building on the interior, airtightness of these types of retrofits, multi-unit building compartmentalization, window selection, and roof insulation strategies. Mechanical system items include combined hydronic and space heating systems with hydronic distribution in small (low load) units, and ventilation system retrofits for multifamily buildings.« less

Retrofit of a MultiFamily Mass Masonry Building in New England

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ueno, K.; Kerrigan, P.; Wytrykowska, H.

2013-08-01

Merrimack Valley Habitat for Humanity (MVHfH) has partnered with Building Science Corporation to provide high performance affordable housing for 10 families in the retrofit of an existing brick building (a former convent) into condominiums. The research performed for this project provides information regarding advanced retrofit packages for multi-family masonry buildings in Cold climates. In particular, this project demonstrates safe, durable, and cost-effective solutions that will potentially benefit millions of multi-family brick buildings throughout the East Coast and Midwest (Cold climates). The retrofit packages provide insight on the opportunities for and constraints on retrofitting multifamily buildings with ambitious energy performance goalsmore » but a limited budget. The condominium conversion project will contribute to several areas of research on enclosures, space conditioning, and water heating. Enclosure items include insulation of mass masonry building on the interior, airtightness of these types of retrofits, multi-unit building compartmentalization, window selection, and roof insulation strategies. Mechanical system items include combined hydronic and space heating systems with hydronic distribution in small (low load) units, and ventilation system retrofits for multifamily buildings.« less

Final Technical Report. Training in Building Audit Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brosemer, Kathleen

In 2011, the Tribe proposed and was awarded the Training in Building Audit Technologies grant from the DOE in the amount of $55,748 to contract for training programs for infrared cameras, blower door technology applications and building systems. The coursework consisted of; Infrared Camera Training: Level I - Thermal Imaging for Energy Audits; Blower Door Analysis and Building-As-A-System Training, Building Performance Institute (BPI) Building Analyst; Building Envelope Training, Building Performance Institute (BPI) Envelope Professional; and Audit/JobFLEX Tablet Software. Competitive procurement of the training contractor resulted in lower costs, allowing the Tribe to request and receive DOE approval to additionally purchasemore » energy audit equipment and contract for residential energy audits of 25 low-income Tribal Housing units. Sault Tribe personnel received field training to supplement the classroom instruction on proper use of the energy audit equipment. Field experience was provided through the second DOE energy audits grant, allowing Sault Tribe personnel to join the contractor, Building Science Academy, in conducting 25 residential energy audits of low-income Tribal Housing units.« less

Guidelines for testing and release procedures

NASA Technical Reports Server (NTRS)

Molari, R.; Conway, M.

1984-01-01

Guidelines and procedures are recommended for the testing and release of the types of computer software efforts commonly performed at NASA/Ames Research Center. All recommendations are based on the premise that testing and release activities must be specifically selected for the environment, size, and purpose of each individual software project. Guidelines are presented for building a Test Plan and using formal Test Plan and Test Care Inspections on it. Frequent references are made to NASA/Ames Guidelines for Software Inspections. Guidelines are presented for selecting an Overall Test Approach and for each of the four main phases of testing: (1) Unit Testing of Components, (2) Integration Testing of Components, (3) System Integration Testing, and (4) Acceptance Testing. Tools used for testing are listed, including those available from operating systems used at Ames, specialized tools which can be developed, unit test drivers, stub module generators, and the use of format test reporting schemes.

Prognostic Physiology: Modeling Patient Severity in Intensive Care Units Using Radial Domain Folding

PubMed Central

Joshi, Rohit; Szolovits, Peter

2012-01-01

Real-time scalable predictive algorithms that can mine big health data as the care is happening can become the new “medical tests” in critical care. This work describes a new unsupervised learning approach, radial domain folding, to scale and summarize the enormous amount of data collected and to visualize the degradations or improvements in multiple organ systems in real time. Our proposed system is based on learning multi-layer lower dimensional abstractions from routinely generated patient data in modern Intensive Care Units (ICUs), and is dramatically different from most of the current work being done in ICU data mining that rely on building supervised predictive models using commonly measured clinical observations. We demonstrate that our system discovers abstract patient states that summarize a patient’s physiology. Further, we show that a logistic regression model trained exclusively on our learned layer outperforms a customized SAPS II score on the mortality prediction task. PMID:23304406

Design and development of an electrically-controlled beam steering mirror for microwave tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tayebi, A., E-mail: tayebiam@msu.edu; Tang, J.; Paladhi, P. Roy

2015-03-31

Microwave tomography has gained significant attention due to its reliability and unhazardous nature in the fields of NDE and medical industry. A new microwave tomography system is presented in this paper, which significantly reduces the design and operational complexities of traditional microwave imaging systems. The major component of the proposed system is a reconfigurable reflectarray antenna which is used for beam steering in order to generate projections from multiple angles. The design, modeling and fabrication of the building block of the antenna, a tunable unit cell, are discussed in this paper. The unit cell is capable of dynamically altering themore » phase of the reflected field which results in beam steering ability of the reflectarray antenna. A tomographically reconstructed image of a dielectric sample using this new microwave tomography system is presented in this work.« less

KSC-2011-7549

NASA Image and Video Library

2011-10-26

VANDENBERG AIR FORCE BASE, Calif. -- Vernon Thorp, program manager, NASA missions, United Launch Alliance, Cape Canaveral, Fla., participates in the prelaunch news conference at Vandenberg Air Force Base, Calif., for NASA’s National Polar-orbiting Operational Environmental Satellite System Preparatory Project (NPP) spacecraft. NPP represents a critical first step in building the next-generation of Earth-observing satellites. NPP will carry the first of the new sensors developed for this satellite fleet, now known as the Joint Polar Satellite System (JPSS), to be launched in 2016. NPP is the bridge between NASA's Earth Observing System (EOS) satellites and the forthcoming series of JPSS satellites. The mission will test key technologies and instruments for the JPSS missions. NPP is targeted to launch Oct. 28 from Space Launch Complex-2 aboard a United Launch Alliance Delta II rocket. For more information, visit http://www.nasa.gov/NPP. Photo credit: NASA/VAFB

KSC-2011-7543

NASA Image and Video Library

2011-10-26

VANDENBERG AIR FORCE BASE, Calif. -- A model of the NASA’s National Polar-orbiting Operational Environmental Satellite System Preparatory Project (NPP) spacecraft and the United Launch Alliance Delta II rocket are displayed during the prelaunch news conference at Vandenberg Air Force Base, Calif. NPP represents a critical first step in building the next-generation of Earth-observing satellites. NPP will carry the first of the new sensors developed for this satellite fleet, now known as the Joint Polar Satellite System (JPSS), to be launched in 2016. NPP is the bridge between NASA's Earth Observing System (EOS) satellites and the forthcoming series of JPSS satellites. The mission will test key technologies and instruments for the JPSS missions. NPP is targeted to launch Oct. 28 from Space Launch Complex-2 aboard a United Launch Alliance Delta II rocket. For more information, visit http://www.nasa.gov/NPP. Photo credit: NASA/VAFB

Spring Ankle with Regenerative Kinetics to Build a New Generation of Transtibial Prostheses

DTIC Science & Technology

2008-07-31

form factor that is portable to the wearer. The objective is to build a transtibial prosthesis that will support a Military amputee’s return to...active duty. 15. SUBJECT TERMS Transtibial Prosthesis , regenerative, spring, wearable robot 16. SECURITY CLASSIFICATION OF: 17. LIMITATION...Regenerative Kinetics” to build a new generation of transtibial prostheses Keywords: Transtibial Prosthesis , regenerative, spring, wearable robot

Multigenerational Challenges: Team-Building for Positive Clinical Workforce Outcomes

PubMed

Moore, Jill M; Everly, Marcee; Bauer, Renee

2016-05-31

Patient acuity in hospital settings continues to increase, and there is greater emphasis on patient outcomes. The current nursing workforce is comprised of four distinct generational cohorts that include veterans, baby boomers, millennials, and generation Xers. Each group has unique characteristics that add complexity to the workforce and this can add challenges to providing optimal patient care. Team building is one strategy to increase mutual understanding, communication, and respect, and thus potentially improve patient outcomes. In this article, we first briefly define generational cohorts by characteristics, and discuss differing expectations for work/life balance and potential negative outcomes. Our discussion offers team building strategies for positive outcomes, a case scenario, and concludes with resources for team building and organizational opportunities.

1. Historic American Buildings Survey, August, 1971 SOUTH (FRONT) ELEVATIONS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Historic American Buildings Survey, August, 1971 SOUTH (FRONT) ELEVATIONS OF CORNER OF UNITED STATES HOTEL (FAR LEFT), JUDGE AND NUNAN'S SADDLERY, P.J. RYAN'S FIRST BRICK STORE BUILDING (JACKSONVILLE INN). - P. J. Ryan's First Brick Store Building, 175 East California Street, Jacksonville, Jackson County, OR

26 CFR 1.263(a)-0 - Outline of regulations under section 263(a).

Code of Federal Regulations, 2014 CFR

2014-04-01

... amounts paid for improvements. (e) Determining the unit of property. (1) In general. (2) Building. (i) In general. (ii) Application of improvement rules to a building. (A) Building structure. (B) Building system. (iii) Condominium. (A) In general. (B) Application of improvement rules to a condominium. (iv...

Large-scale building scenes reconstruction from close-range images based on line and plane feature

NASA Astrophysics Data System (ADS)

Ding, Yi; Zhang, Jianqing

2007-11-01

Automatic generate 3D models of buildings and other man-made structures from images has become a topic of increasing importance, those models may be in applications such as virtual reality, entertainment industry and urban planning. In this paper we address the main problems and available solution for the generation of 3D models from terrestrial images. We first generate a coarse planar model of the principal scene planes and then reconstruct windows to refine the building models. There are several points of novelty: first we reconstruct the coarse wire frame model use the line segments matching with epipolar geometry constraint; Secondly, we detect the position of all windows in the image and reconstruct the windows by established corner points correspondences between images, then add the windows to the coarse model to refine the building models. The strategy is illustrated on image triple of college building.

1. MISSILE TEST AND ASSEMBLY BUILDING, FRONT, LOOKING SOUTH. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. MISSILE TEST AND ASSEMBLY BUILDING, FRONT, LOOKING SOUTH. - NIKE Missile Base SL-40, Missile Test & Assembly Building, South end of launch area, northeast of Generator Building No. 3, Hecker, Monroe County, IL

D Building Reconstruction by Multiview Images and the Integrated Application with Augmented Reality

NASA Astrophysics Data System (ADS)

Hwang, Jin-Tsong; Chu, Ting-Chen

2016-10-01

This study presents an approach wherein photographs with a high degree of overlap are clicked using a digital camera and used to generate three-dimensional (3D) point clouds via feature point extraction and matching. To reconstruct a building model, an unmanned aerial vehicle (UAV) is used to click photographs from vertical shooting angles above the building. Multiview images are taken from the ground to eliminate the shielding effect on UAV images caused by trees. Point clouds from the UAV and multiview images are generated via Pix4Dmapper. By merging two sets of point clouds via tie points, the complete building model is reconstructed. The 3D models are reconstructed using AutoCAD 2016 to generate vectors from the point clouds; SketchUp Make 2016 is used to rebuild a complete building model with textures. To apply 3D building models in urban planning and design, a modern approach is to rebuild the digital models; however, replacing the landscape design and building distribution in real time is difficult as the frequency of building replacement increases. One potential solution to these problems is augmented reality (AR). Using Unity3D and Vuforia to design and implement the smartphone application service, a markerless AR of the building model can be built. This study is aimed at providing technical and design skills related to urban planning, urban designing, and building information retrieval using AR.

Building clinical trial capacity to develop a new treatment for multidrug-resistant tuberculosis.

PubMed

Tupasi, Thelma; Gupta, Rajesh; Danilovits, Manfred; Cirule, Andra; Sanchez-Garavito, Epifanio; Xiao, Heping; Cabrera-Rivero, Jose L; Vargas-Vasquez, Dante E; Gao, Mengqiu; Awad, Mohamed; Gentry, Leesa M; Geiter, Lawrence J; Wells, Charles D

2016-02-01

New drugs for infectious diseases often need to be evaluated in low-resource settings. While people working in such settings often provide high-quality care and perform operational research activities, they generally have less experience in conducting clinical trials designed for drug approval by stringent regulatory authorities. We carried out a capacity-building programme during a multi-centre randomized controlled trial of delamanid, a new drug for the treatment of multidrug-resistant tuberculosis. The programme included: (i) site identification and needs assessment; (ii) achieving International Conference on Harmonization - Good Clinical Practice (ICH-GCP) standards; (iii) establishing trial management; and (iv) increasing knowledge of global and local regulatory issues. Trials were conducted at 17 sites in nine countries (China, Egypt, Estonia, Japan, Latvia, Peru, the Philippines, the Republic of Korea and the United States of America). Eight of the 10 sites in low-resource settings had no experience in conducting the requisite clinical trials. Extensive capacity-building was done in all 10 sites. The programme resulted in improved local capacity in key areas such as trial design, data safety and monitoring, trial conduct and laboratory services. Clinical trials designed to generate data for regulatory approval require additional efforts beyond traditional research-capacity strengthening. Such capacity-building approaches provide an opportunity for product development partnerships to improve health systems beyond the direct conduct of the specific trial.

WASTE HANDLING BUILDING ELECTRICAL SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.C. Khamamkar

2000-06-23

The Waste Handling Building Electrical System performs the function of receiving, distributing, transforming, monitoring, and controlling AC and DC power to all waste handling building electrical loads. The system distributes normal electrical power to support all loads that are within the Waste Handling Building (WHB). The system also generates and distributes emergency power to support designated emergency loads within the WHB within specified time limits. The system provides the capability to transfer between normal and emergency power. The system provides emergency power via independent and physically separated distribution feeds from the normal supply. The designated emergency electrical equipment will bemore » designed to operate during and after design basis events (DBEs). The system also provides lighting, grounding, and lightning protection for the Waste Handling Building. The system is located in the Waste Handling Building System. The system consists of a diesel generator, power distribution cables, transformers, switch gear, motor controllers, power panel boards, lighting panel boards, lighting equipment, lightning protection equipment, control cabling, and grounding system. Emergency power is generated with a diesel generator located in a QL-2 structure and connected to the QL-2 bus. The Waste Handling Building Electrical System distributes and controls primary power to acceptable industry standards, and with a dependability compatible with waste handling building reliability objectives for non-safety electrical loads. It also generates and distributes emergency power to the designated emergency loads. The Waste Handling Building Electrical System receives power from the Site Electrical Power System. The primary material handling power interfaces include the Carrier/Cask Handling System, Canister Transfer System, Assembly Transfer System, Waste Package Remediation System, and Disposal Container Handling Systems. The system interfaces with the MGR Operations Monitoring and Control System for supervisory monitoring and control signals. The system interfaces with all facility support loads such as heating, ventilation, and air conditioning, office, fire protection, monitoring and control, safeguards and security, and communications subsystems.« less

Characterization of 618-11 solid waste burial ground, disposed waste, and description of the waste generating facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hladek, K.L.

1997-10-07

The 618-11 (Wye or 318-11) burial ground received transuranic (TRTJ) and mixed fission solid waste from March 9, 1962, through October 2, 1962. It was then closed for 11 months so additional burial facilities could be added. The burial ground was reopened on September 16, 1963, and continued operating until it was closed permanently on December 31, 1967. The burial ground received wastes from all of the 300 Area radioactive material handling facilities. The purpose of this document is to characterize the 618-11 solid waste burial ground by describing the site, burial practices, the disposed wastes, and the waste generatingmore » facilities. This document provides information showing that kilogram quantities of plutonium were disposed to the drum storage units and caissons, making them transuranic (TRU). Also, kilogram quantities of plutonium and other TRU wastes were disposed to the three trenches, which were previously thought to contain non-TRU wastes. The site burial facilities (trenches, caissons, and drum storage units) should be classified as TRU and the site plutonium inventory maintained at five kilograms. Other fissile wastes were also disposed to the site. Additionally, thousands of curies of mixed fission products were also disposed to the trenches, caissons, and drum storage units. Most of the fission products have decayed over several half-lives, and are at more tolerable levels. Of greater concern, because of their release potential, are TRU radionuclides, Pu-238, Pu-240, and Np-237. TRU radionuclides also included slightly enriched 0.95 and 1.25% U-231 from N-Reactor fuel, which add to the fissile content. The 618-11 burial ground is located approximately 100 meters due west of Washington Nuclear Plant No. 2. The burial ground consists of three trenches, approximately 900 feet long, 25 feet deep, and 50 feet wide, running east-west. The trenches constitute 75% of the site area. There are 50 drum storage units (five 55-gallon steel drums welded together) buried in three rows in the northeast comer. In addition, five eight-foot diameter caissons are located at the west end of the center row of the drum storage units. Initially, wastes disposed to the caissons and drum storage units were from the 325 and 327 building hot cells. Later, a small amount of remote-handled (RH) waste from the 309 building Plutonium Recycle Test Reactor (PRTR) cells, and the newly built 324 building hot cells, was disposed at the site.« less

Life cycle assessment and environmental building declaration for the design building at the University of Massachusetts

Treesearch

Hongmei Gu; Richard Bergman

2018-01-01

AbstractWith the world’s increasing focus on sustainability in the construction sector through green building systems, the U.S. Department of Agriculture (USDA) has been ac-tively engaged in green building advocacy in the United States through USDA Tall Wood Building competitions and follow-up research on use of mass timber for nonresi-dential buildings. The USDA...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weinstein, R.E.; Goldstein, H.N.; White, J.S.

It is often more economical to keep existing generation capacity in operation than to build new capacity. Repowering is considered at a number of sites because of the need for added capacity, the poor condition of plant equipment (particularly the boiler), the need for improved environmental performance, the need for shorter licensing period, and other reasons. This paper describes the results of a US Department of Energy (DOE) conceptual design evaluation of an early commercial repowering application of advanced circulating pressurized fluidized bed combustion combined cycle technology (APFBC). The paper provides a review of the DOE study and summarizes themore » preliminary results. This all-coal technology has projected energy efficiency in the 42 to 46% HHV (43 to 48% LHV) range and environmental emissions superior to New Source Performance Standards (NSPS). A DOE-sponsored demonstration program will pioneer the first commercial APFBC demonstration in year 2001. That 170 MWe APFBC CCT demonstration will use all new equipment, and become the City of Lakeland`s C.D. McIntosh, Jr. steam plant Unit 4. This paper`s concept evaluation is for a larger implementation. A modern large frame combustion turbine is used to produce a 300 + MWe class APFBC. At this size, APFBC has a wide application for repowering many existing units in America. Here, APFBC would repower an existing generation station, the Carolina Power and Light Company`s (CP and L) L.V. Suttong steam station. Repowering concepts are presented for APFBC repowering of Unit 2 (252 MWe) and of both Units 1 and 2 in combination (360 MWe total).« less

Hydrodynamic film thickness measurements and CFD analysis identify the root causes of repetitive thrust bearing failures on a 45 MW hydro generating unit at Hydro-Québec

NASA Astrophysics Data System (ADS)

Gauvin, P.; Huard, P.

2016-11-01

High temperature level recorded on the thrust bearing of a 45 MW hydro generating unit was resulting in frequent production stoppage. In spite of improvements brought to the oil cooling system since the rehabilitation in 2008, the operator had to activate the bearing oil lift system to keep the temperature below acceptable limits. Primary root cause analysis first pointed to the design of the shoe that was centrally pivoted, not allowing the formation of a thick hydrodynamic film. The removal of a strip of the soft metal layer near the trailing edge of the shoe resulted in a significant surface temperature reduction (about 15 deg. C), as predicted by a CFD model of the oil film. The goal of this machining was to increase the pivoting angle by moving the centre of hydrodynamic pressure. Proximity sensors were installed at each corner of the redesigned shoe to measure the film thickness and the bearing attitude. Signal analysis revealed a step of a magnitude close to the oil film thickness between the two halves of the rotating thrust block. This was the cause of another failure few hours since restarting the unit. The lessons learnt through these measurements and analyses were carefully applied to the ultimate build. The unit now runs with a robust thrust bearing and even survived a significant cooling flow reduction event. This paper presents the CFD analysis results and the measurements acquired during these events.

Indoor-Outdoor Air Leakage of Apartments and Commercial Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Price, P.N.; Shehabi, A.; Chan, R.W.

We compiled and analyzed available data concerning indoor-outdoor air leakage rates and building leakiness parameters for commercial buildings and apartments. We analyzed the data, and reviewed the related literature, to determine the current state of knowledge of the statistical distribution of air exchange rates and related parameters for California buildings, and to identify significant gaps in the current knowledge and data. Very few data were found from California buildings, so we compiled data from other states and some other countries. Even when data from other developed countries were included, data were sparse and few conclusive statements were possible. Little systematicmore » variation in building leakage with construction type, building activity type, height, size, or location within the u.s. was observed. Commercial buildings and apartments seem to be about twice as leaky as single-family houses, per unit of building envelope area. Although further work collecting and analyzing leakage data might be useful, we suggest that a more important issue may be the transport of pollutants between units in apartments and mixed-use buildings, an under-studied phenomenon that may expose occupants to high levels of pollutants such as tobacco smoke or dry cleaning fumes.« less

G-CNV: A GPU-Based Tool for Preparing Data to Detect CNVs with Read-Depth Methods.

PubMed

Manconi, Andrea; Manca, Emanuele; Moscatelli, Marco; Gnocchi, Matteo; Orro, Alessandro; Armano, Giuliano; Milanesi, Luciano

2015-01-01

Copy number variations (CNVs) are the most prevalent types of structural variations (SVs) in the human genome and are involved in a wide range of common human diseases. Different computational methods have been devised to detect this type of SVs and to study how they are implicated in human diseases. Recently, computational methods based on high-throughput sequencing (HTS) are increasingly used. The majority of these methods focus on mapping short-read sequences generated from a donor against a reference genome to detect signatures distinctive of CNVs. In particular, read-depth based methods detect CNVs by analyzing genomic regions with significantly different read-depth from the other ones. The pipeline analysis of these methods consists of four main stages: (i) data preparation, (ii) data normalization, (iii) CNV regions identification, and (iv) copy number estimation. However, available tools do not support most of the operations required at the first two stages of this pipeline. Typically, they start the analysis by building the read-depth signal from pre-processed alignments. Therefore, third-party tools must be used to perform most of the preliminary operations required to build the read-depth signal. These data-intensive operations can be efficiently parallelized on graphics processing units (GPUs). In this article, we present G-CNV, a GPU-based tool devised to perform the common operations required at the first two stages of the analysis pipeline. G-CNV is able to filter low-quality read sequences, to mask low-quality nucleotides, to remove adapter sequences, to remove duplicated read sequences, to map the short-reads, to resolve multiple mapping ambiguities, to build the read-depth signal, and to normalize it. G-CNV can be efficiently used as a third-party tool able to prepare data for the subsequent read-depth signal generation and analysis. Moreover, it can also be integrated in CNV detection tools to generate read-depth signals.

Aminobenzoates as building blocks for natural product assembly lines.

PubMed

Walsh, Christopher T; Haynes, Stuart W; Ames, Brian D

2012-01-01

The ortho-, meta-, and para- regioisomers of aminobenzoate are building blocks for a wide range of microbial natural products. Both the ortho-isomer (anthranilate) and PABA derive from the central shikimate pathway metabolite chorismate while the meta-isomer is not available by that route and starts from UDP-3-aminoglucose. PABA is largely funnelled into folate biosynthesis while anthranilate is the scaffold for biosynthetic elaboration into many natural heterocycles, most notably with its role in indole formation for tryptophan biosynthesis. Anthranilate is also converted to benzodiazepinones, fumiquinazolines, quinoxalines, phenoxazines, benzoxazolinates, quinolones, and phenazines, often with redox enzyme participation. The 5-hydroxy form of 3-aminobenzaote is the starter unit for ansa-bridged rifamycins, ansamitocins, and geldanamycins, whereas regioisomers 2-hydroxy, 4-hydroxy and 2,4-dihydroxy-3-aminobenzoate are key components of antimycin, grixazone, and platencin and platensimycin biosynthesis, respectively. The enzymatic mechanisms for generation of the aminobenzoate regioisomers and their subsequent utilization for diverse heterocycle and macrocycle construction are examined.

TEWI Evaluation for Refrigeration and Air-Conditioning Systems in Office Buildings with Different Regional Heat Demand

NASA Astrophysics Data System (ADS)

Sobue, Atsushi; Watanabe, Koichi

In the present study, we quantitatively evaluated the global warming impact by refrigeration and air-conditioning systems in office buildings on the basis of reliable TEWI information. This paper proposes an improved TEWI evaluation procedure by considering regional heat demands and part load of air-conditioning systems. In the TEWI evaluation of commercial chillers, a percentage of the impact by refrigerant released to the atmosphere (direct effect) is less than 19.9% in TEWI values. Therefore, a reduction of the impact by CO2 released as a result of the energy consumed to drive the refrigeration or air-conditioning systems through out their lifetime (indirect effect) is the most effective measure in reducing the global warming impact. On the other hand, we have also pointed out energy loss that might be generated by an excess investment to the equipment. We have also showed a usefulness in dividing the heating / cooling system into several small-capacity units so as to improve the energy utilization efficiency.

The Crosstown initiative: art, community, and placemaking in Memphis.

PubMed

Thomas, Elizabeth; Pate, Sarah; Ranson, Anna

2015-03-01

This case study examines an arts organization at the center of an urban neighborhood revitalization effort and its contributions to creative placemaking and inclusive community building. The study documents innovative arts practices and explores their meaning for a local context, an understudied city in the Mid-South region of the United States. It builds on the research team's ongoing work as teachers, students, and scholars in partnership with the arts organization. It includes systematic participant observation, interviews with stakeholders, and a review of historical and contemporary media coverage. We found that the organization and its practices provided a rich context for exploring an expanded sense of community including bridging social capital and place-based frameworks. Analysis suggests that the organization's intentional arts based practices bring multiple understandings of community and art into meaningful dialogue through the generation of creative and social friction. These practices illustrate one context-specific strategy addressing the tensions in a community-diversity dialectic (Townley et al. in Am J Commun Psychol 47:69-85, 2011).

4. MISSILE TEST AND ASSEMBLY BUILDING, LEFT SIDE, LOOKING NORTH. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. MISSILE TEST AND ASSEMBLY BUILDING, LEFT SIDE, LOOKING NORTH. - NIKE Missile Base SL-40, Missile Test & Assembly Building, South end of launch area, northeast of Generator Building No. 3, Hecker, Monroe County, IL

2. MISSILE TEST AND ASSEMBLY BUILDING, RIGHT SIDE, LOOKING WEST. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. MISSILE TEST AND ASSEMBLY BUILDING, RIGHT SIDE, LOOKING WEST. - NIKE Missile Base SL-40, Missile Test & Assembly Building, South end of launch area, northeast of Generator Building No. 3, Hecker, Monroe County, IL

3. MISSILE TEST AND ASSEMBLY BUILDING, REAR SIDE, LOOKING NORTH. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. MISSILE TEST AND ASSEMBLY BUILDING, REAR SIDE, LOOKING NORTH. - NIKE Missile Base SL-40, Missile Test & Assembly Building, South end of launch area, northeast of Generator Building No. 3, Hecker, Monroe County, IL

Planification de la maintenance d'un parc de turbines-alternateurs par programmation mathematique

NASA Astrophysics Data System (ADS)

Aoudjit, Hakim

A growing number of Hydro-Quebec's hydro generators are at the end of their useful life and maintenance managers fear to face a number of overhauls exceeding what can be handled. Maintenance crews and budgets are limited and these withdrawals may take up to a full year and mobilize significant resources in addition to the loss of electricity production. In addition, increased export sales forecasts and severe production patterns are expected to speed up wear that can lead to halting many units at the same time. Currently, expert judgment is at the heart of withdrawals which rely primarily on periodic inspections and in-situ measurements and the results are sent to the maintenance planning team who coordinate all the withdrawals decisions. The degradations phenomena taking place is random in nature and the prediction capability of wear using only inspections is limited to short-term at best. A long term planning of major overhauls is sought by managers for the sake of justifying and rationalizing budgets and resources. The maintenance managers are able to provide a huge amount of data. Among them, is the hourly production of each unit for several years, the repairs history on each part of a unit as well as major withdrawals since the 1950's. In this research, we tackle the problem of long term maintenance planning for a fleet of 90 hydro generators at Hydro-Quebec over a 50 years planning horizon period. We lay a scientific and rational framework to support withdrawals decisions by using part of the available data and maintenance history while fulfilling a set of technical and economic constraints. We propose a planning approach based on a constrained optimization framework. We begin by decomposing and sorting hydro generator components to highlight the most influential parts. A failure rate model is developed to take into account the technical characteristics and unit utilization. Then, replacement and repair policies are evaluated for each of the components then strategies are derived for the whole unit. Traditional univariate policies such as the age replacement policy and the minimal repair policy are calculated. These policies are extended to build alternative bivariate maintenance policy as well as a repair strategy where the state of a component after a repair is rejuvenated by a constant coefficient. These templates form the basis for the calculation of objective function for the scheduling problem. On one hand, this issue is treated as a nonlinear problem where the objective is to minimize the average total maintenance cost per unit of time on an infinite horizon for the fleet with technical and economic constraints. A formulation is also proposed in the case of a finite time horizon. In the event of electricity production variation, and given that the usage profile is known, the influence of production scenarios is reflected on the unit's components through their failure rate. In this context, prognoses on possible resources problems are made by studying the characteristics of the generated plans. On the second hand, the withdrawals are now subjected to two decision criteria. In addition to minimizing the average total maintenance cost per unit of time on an infinite time horizon, the best achievable reliability of remaining turbo generators is sought. This problem is treated as a biobjective nonlinear optimization problem. Finally a series of problems describing multiple contexts are solved for planning renovations of 90 turbo generators units considering 3 major components in each unit and 2 types of maintenance policies for each component.

Interior view of ground floor unit at west end of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view of ground floor unit at west end of Building No. 23, looking from front door with kitchen on left, living room to right, bedrooms and bath at center rear. Looking east - Easter Hill Village, Building No. 23, North side of South Twenty-sixth Street, east of Corto Square, Richmond, Contra Costa County, CA

Construction of a polyhedron decorated MOF with a unique network through the combination of two classic secondary building units.

PubMed

Ren, Guo-Jian; Chang, Ze; Xu, Jian; Hu, Zhenpeng; Liu, Yan-Qing; Xu, Yue-Ling; Bu, Xian-He

2016-02-04

A novel decorated metal-organic polyhedron (MOP) based metal-organic framework with a unique 4,9-connected network is successfully constructed, which displays a relatively strong interaction toward H2 and CO2 probably due to the existence of open metal sites in the secondary building units.

To designate the Federal building and United States courthouse located at 101 Barr Street in Lexington, Kentucky, as the "Scott Reed Federal Building and United States Courthouse".

THOMAS, 111th Congress

Rep. Chandler, Ben [D-KY-6

2009-02-04

Senate - 03/11/2009 Received in the Senate and Read twice and referred to the Committee on Environment and Public Works. (All Actions) Tracker: This bill has the status Passed HouseHere are the steps for Status of Legislation:

38 CFR 36.4361 - Acceptable ownership arrangements and documentation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... condominium, including building types, architectural style and the size of the units for those phases of the..., building types, architectural style and size of the units, etc. of these phases. However, the minimum... elements. (See § 36.4864(a)(6).) (Authority: 38 U.S.C. 3703(c)(1), 3710(a)(6)) (The Office of Management...

Sanitary Schoolhouses: Legal Requirements in Indiana and Ohio. Bulletin, 1913, No. 52. Whole Number 563

ERIC Educational Resources Information Center

United States Bureau of Education, Department of the Interior, 1913

1913-01-01

Scores of millions of dollars are spent annually in the United States for new school buildings. With this large. expenditure has come a general desire that schoolhouses shall be usable, healthful, comfortable, and beautiful. Educators and architects have united in devising plans for school buildings. This bureau has published a valuable bulletin…

How to Break through Techno-Shock and Build Multi-Media Units.

ERIC Educational Resources Information Center

Sutz, Rachel; Warren, Maria W.; Williams, Holly

1998-01-01

Describes how three teachers learned about using Hyperstudio (presentation software), constructed a Web page, and created an original film as part of a unit on Florida writers. Recommends three major strategies for learning a new technology: choose the literary works, then the technology; build on your strengths; and learn to talk to the…

The Organic Secondary Building Unit: Strong Intermolecular π Interactions Define Topology in MIT-25, a Mesoporous MOF with Proton-Replete Channels.

PubMed

Park, Sarah S; Hendon, Christopher H; Fielding, Alistair J; Walsh, Aron; O'Keeffe, Michael; Dincă, Mircea

2017-03-15

The structure-directing role of the inorganic secondary building unit (SBU) is key for determining the topology of metal-organic frameworks (MOFs). Here we show that organic building units relying on strong π interactions that are energetically competitive with the formation of common inorganic SBUs can also play a role in defining the topology. We demonstrate the importance of the organic SBU in the formation of Mg 2 H 6 (H 3 O)(TTFTB) 3 (MIT-25), a mesoporous MOF with the new ssp topology. A delocalized electronic hole is critical in the stabilization of the TTF triad organic SBUs and exemplifies a design principle for future MOF synthesis.

The new nuclear west: Uranium milling as community on Colorado's western slope

NASA Astrophysics Data System (ADS)

Tidwell, Abraham S. D.

In mid-2007, Energy Fuels, a Toronto-based uranium mining and milling company, announced their intent to build Piñon Ridge, the first new conventional uranium mill in the United States in 30 years. The prospect of a return to uranium milling has mobilized community support to bring back an industry some see as both familiar and capable of supporting and growing their communities. Using transcripts generated during the Colorado Department of Public Health and Environment's public meetings and hearings during 2010 and 2012, this study examines how proponents of the mill frame the socioeconomic advantages of bringing the industry back. Applying Kinsella's bounded constitutive model of communication, this study shows that the community and the uranium mill are bound in a "sorge-enframing" duality where the care generated by each binds the other to the recalcitrant nature of the uranium industry and preconceived notions of socioeconomic development, respectively.

Progress on 241Am Production for Use in Radioisotope Power Systems

NASA Astrophysics Data System (ADS)

Baker, S. R.; Bell, K. J.; Brown, J.; Carrigan, C.; Carrott, M. J.; Gregson, C.; Clough, M.; Maher, C. J.; Mason, C.; Rhodes, C. J.; Rice, T. G.; Sarsfield, M. J.; Stephenson, K.; Taylor, R. J.; Tinsley, T. P.; Woodhead, D. A.; Wiss, T.

2014-08-01

Electrical power sources used in outer planet missions are a key enabling technology for data acquisition and communications. Power sources generate electricity from the thermal energy from alpha decay of the radioisotope 238Pu via thermo-electric conversion. Production of 238Pu requires specialist facilities including a nuclear reactor and reprocessing plants that are expensive to build and operate, so naturally, a more economical alternative is attractive to the industry. Within Europe 241Am is a feasible alternative to 238Pu that can provide a heat source for radioisotope thermoelectric generators (RTGs) and radioisotope heating units (RHUs). As a daughter product of 241Pu decay, 241Am is present at 1000s kg levels within the UK civil plutonium stockpile.A chemical separation process is required to extract the 241Am in a pure form and this paper describes such a process, successfully developed to the proof of concept stage.

Automatic Large-Scalae 3d Building Shape Refinement Using Conditional Generative Adversarial Networks

NASA Astrophysics Data System (ADS)

Bittner, K.; d'Angelo, P.; Körner, M.; Reinartz, P.

2018-05-01

Three-dimensional building reconstruction from remote sensing imagery is one of the most difficult and important 3D modeling problems for complex urban environments. The main data sources provided the digital representation of the Earths surface and related natural, cultural, and man-made objects of the urban areas in remote sensing are the digital surface models (DSMs). The DSMs can be obtained either by light detection and ranging (LIDAR), SAR interferometry or from stereo images. Our approach relies on automatic global 3D building shape refinement from stereo DSMs using deep learning techniques. This refinement is necessary as the DSMs, which are extracted from image matching point clouds, suffer from occlusions, outliers, and noise. Though most previous works have shown promising results for building modeling, this topic remains an open research area. We present a new methodology which not only generates images with continuous values representing the elevation models but, at the same time, enhances the 3D object shapes, buildings in our case. Mainly, we train a conditional generative adversarial network (cGAN) to generate accurate LIDAR-like DSM height images from the noisy stereo DSM input. The obtained results demonstrate the strong potential of creating large areas remote sensing depth images where the buildings exhibit better-quality shapes and roof forms.

4. DETAIL ALONG WEST SIDE, SHOWING EXTERIOR STAIRWAY, BUILDING NO. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. DETAIL ALONG WEST SIDE, SHOWING EXTERIOR STAIRWAY, BUILDING NO. 1 IN THE CENTER DISTANCE, AND ONE OF THE BENDING SHOPS AT RIGHT. - United Engineering Company Shipyard, Engineering Building, 2900 Main Street, Alameda, Alameda County, CA

53. VIEW LOOKING S.E. AT THE CATALYZER BUILDINGS, COOLING SHEDS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

53. VIEW LOOKING S.E. AT THE CATALYZER BUILDINGS, COOLING SHEDS AND ABSORPTION BUILDINGS IN THE BACKGROUND. MAY 29, 1919. - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

Climate change impact on operation of dams and hydroelectricity generation in the Northeastern United States

NASA Astrophysics Data System (ADS)

Ehsani, N.; Vorosmarty, C. J.; Fekete, B. M.

2016-12-01

We are using a large-scale, high-resolution, fully integrated hydrological/reservoir/hydroelectricity model to investigate the impact of climate change on the operation of 11037 dams and generation of electricity from 375 hydroelectric power plants in the Northeastern United States. Moreover, we estimate the hydropower potential of the region by energizing the existing non-powered dams and then studying the impact of climate change on the hydropower potential. We show that climate change increases the impact of dams on the hydrology of the region. Warmer temperatures produce shorter frozen periods, earlier snowmelt and elevated evapotranspiration rates, which when combined with changes in precipitation, are projected to increase water availability in winter but reduce it during summer. As a result, the water that is stored by dams will be more than ever a necessary part of the routine water systems operations to compensate for these seasonal imbalances. The function of dams as emergency water storage for creating drought resiliency will mostly diminish in the future. Building more dams to cope with the local impacts of climate change on water resources and to offset the increased drought vulnerability may thus be inevitable. Annual hydroelectricity generation in the region is 41 Twh. Our estimate of the annual hydropower potential of non-powered dams adds up to 350 Twh. Climate change may reduce hydropower potential from non-powered dams by up to 13% and reduce current hydroelectricity generation by up to 8% annually. Hydroelectricity generation and hydropower potential may increase in winter months and decline in months of summer and fall. These changes call for recalibration of dam operations and may raise conflict of interests in multipurpose dams.

Assembly of tissue engineered blood vessels with spatially-controlled heterogeneities.

PubMed

Strobel, Hannah A; Hookway, Tracy; Piola, Marco; Fiore, Gianfranco Beniamino; Soncini, Monica; Alsberg, Eben; Rolle, Marsha

2018-05-04

Tissue-engineered human blood vessels may enable in vitro disease modeling and drug screening to accelerate advances in vascular medicine. Existing methods for tissue engineered blood vessel (TEBV) fabrication create homogenous tubes not conducive to modeling the focal pathologies characteristic of vascular disease. We developed a system for generating self-assembled human smooth muscle cell ring-units, which were fused together into TEBVs. The goal of this study was to assess the feasibility of modular assembly and fusion of ring building units to fabricate spatially-controlled, heterogeneous tissue tubes. We first aimed to enhance fusion and reduce total culture time, and determined that reducing ring pre-culture duration improved tube fusion. Next, we incorporated electrospun polymer ring units onto tube ends as reinforced extensions, which allowed us to cannulate tubes after only 7 days of fusion, and culture tubes with luminal flow in a custom bioreactor. To create focal heterogeneities, we incorporated gelatin microspheres into select ring units during self-assembly, and fused these rings between ring units without microspheres. Cells within rings maintained their spatial position within tissue tubes after fusion. This work describes a platform approach for creating modular TEBVs with spatially-defined structural heterogeneities, which may ultimately be applied to mimic focal diseases such as intimal hyperplasia or aneurysm.

Building a New Generation of Learning: Conversations to Catalyze Our Construction

ERIC Educational Resources Information Center

Milliron, Mark David; Plinske, Kathleen; Noonan-Terry, Coral

2008-01-01

Rather than focus primarily on the next generation of learners, the authors argue we are best served to focus on building out our on-ground and online infrastructures for a new generation of learning--blending multiple learning modes, technologies, and techniques over the course of the next 15-20 years to serve the diverse array of students from…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendes, Goncalo; Feng, Wei; Stadler, Michael

The following paper conducts a regional analysis of the U.S. and Chinese buildings? potential for adopting Distributed Energy Resources (DER). The expected economics of DER in 2020-2025 is modeled for a commercial and a multi-family residential building in different climate zones. The optimal building energy economic performance is calculated using the Distributed Energy Resources Customer Adoption Model (DER CAM) which minimizes building energy costs for a typical reference year of operation. Several DER such as combined heat and power (CHP) units, photovoltaics, and battery storage are considered. The results indicate DER have economic and environmental competitiveness potential, especially for commercialmore » buildings in hot and cold climates of both countries. In the U.S., the average expected energy cost savings in commercial buildings from DER CAM?s suggested investments is 17percent, while in Chinese buildings is 12percent. The electricity tariffs structure and prices along with the cost of natural gas, represent important factors in determining adoption of DER, more so than climate. High energy pricing spark spreads lead to increased economic attractiveness of DER. The average emissions reduction in commercial buildings is 19percent in the U.S. as a result of significant investments in PV, whereas in China, it is 20percent and driven by investments in CHP. Keywords: Building Modeling and Simulation, Distributed Energy Resources (DER), Energy Efficiency, Combined Heat and Power (CHP), CO2 emissions 1. Introduction The transition from a centralized and fossil-based energy paradigm towards the decentralization of energy supply and distribution has been a major subject of research over the past two decades. Various concerns have brought the traditional model into question; namely its environmental footprint, its structural inflexibility and inefficiency, and more recently, its inability to maintain acceptable reliability of supply. Under such a troubled setting, distributed energy resources (DER) comprising of small, modular, electrical renewable or fossil-based electricity generation units placed at or near the point of energy consumption, has gained much attention as a viable alternative or addition to the current energy system. In 2010, China consumed about 30percent of its primary energy in the buildings sector, leading the country to pay great attention to DER development and its applications in buildings. During the 11th Five Year Plan (FYP), China has implemented 371 renewable energy building demonstration projects, and 210 photovoltaics (PV) building integration projects. At the end of the 12th FYP, China is targeting renewable energy to provide 10percent of total building energy, and to save 30 metric tons of CO2 equivalents (mtce) of energy with building integrated renewables. China is also planning to implement one thousand natural gas-based distributed cogeneration demonstration projects with energy utilization rates over 70percent in the 12th FYP. All these policy targets require significant DER systems development for building applications. China?s fast urbanization makes building energy efficiency a crucial economic issue; however, only limited studies have been done that examine how to design and select suitable building energy technologies in its different regions. In the U.S., buildings consumed 40percent of the total primary energy in 2010 [1] and it is estimated that about 14 billion m2 of floor space of the existing building stock will be remodeled over the next 30 years. Most building?s renovation work has been on building envelope, lighting and HVAC systems. Although interest has emerged, less attention is being paid to DER for buildings. This context has created opportunities for research, development and progressive deployment of DER, due to its potential to combine the production of power and heat (CHP) near the point of consumption and delivering multiple benefits to customers, such as cost« less

Mississippi Curriculum Framework for Building Trades (Program CIP: 46.0490--Building Trades, General). Secondary Programs.

ERIC Educational Resources Information Center

Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

This document, which reflects Mississippi's statutory requirement that instructional programs be based on core curricula and performance-based assessment, contains outlines of the instructional units required in local instructional management plans and daily lesson plans for two secondary-level courses in the building trades: building trades I and…

Electrical. Teacher's Guide. Building Maintenance Units of Instruction.

ERIC Educational Resources Information Center

East Texas State Univ., Commerce. Occupational Curriculum Lab.

This teaching guide on electrical building maintenance, one in a series of six publications designed for building maintenance instructors in Texas, is designed to give students an understanding of electricity in order to know how to make basic repairs to the electrical systems in a building. Introductory material provides teachers with information…

5. MISSILE TEST AND ASSEMBLY BUILDING, FRONT AND RIGHT SIDES, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. MISSILE TEST AND ASSEMBLY BUILDING, FRONT AND RIGHT SIDES, LOOKING SOUTHEAST. - NIKE Missile Base SL-40, Missile Test & Assembly Building, South end of launch area, northeast of Generator Building No. 3, Hecker, Monroe County, IL

6. MISSILE TEST AND ASSEMBLY BUILDING, REAR AND LEFT SIDES, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. MISSILE TEST AND ASSEMBLY BUILDING, REAR AND LEFT SIDES, LOOKING NORTHWEST. - NIKE Missile Base SL-40, Missile Test & Assembly Building, South end of launch area, northeast of Generator Building No. 3, Hecker, Monroe County, IL

Residential building energy conservation and avoided power plant emissions by urban and community trees in the United States

Treesearch

David J. Nowak; Nathaniel Appleton; Alexis Ellis; Eric Greenfield

2017-01-01

Urban trees and forests alter building energy use and associated emissions from power plants by shading buildings, cooling air temperatures and altering wind speeds around buildings. Field data on urban trees were combined with local urban/community tree and land cover maps, modeling of tree effects on building energy use and pollutant emissions, and state energy and...

An integrated multi-scale risk analysis procedure for pluvial flooding

NASA Astrophysics Data System (ADS)

Tader, Andreas; Mergili, Martin; Jäger, Stefan; Glade, Thomas; Neuhold, Clemens; Stiefelmeyer, Heinz

2016-04-01

Mitigation of or adaptation to the negative impacts of natural processes on society requires a better understanding of the spatio-temporal distribution not only of the processes themselves, but also of the elements at risk. Information on their values, exposures and vulnerabilities towards the expected impact magnitudes/intensities of the relevant processes is needed. GIS-supported methods are particularly useful for integrated spatio-temporal analyses of natural processes and their potential consequences. Hereby, pluvial floods are of particular concern for many parts of Austria. The overall aim of the present study is to calculate the hazards emanating from pluvial floods, to determine the exposure of given elements at risk, to determine their vulnerabilities towards given pluvial flood hazards and to analyze potential consequences in terms of monetary losses. The whole approach builds on data available on a national scale. We introduce an integrated, multi-scale risk analysis procedure with regard to pluvial flooding. Focusing on the risk to buildings, we firstly exemplify this procedure with a well-documented event in the city of Graz (Austria), in order to highlight the associated potentials and limitations. Secondly, we attempt to predict the possible consequences of pluvial flooding triggered by rainfall events with recurrence intervals of 30, 100 and 300 years. (i) We compute spatially distributed inundation depths using the software FloodArea. Infiltration capacity and surface roughness are estimated from the land cover units given by the official cadastre. Various assumptions are tested with regard to the inflow to the urban sewer system. (ii) Based on the inundation depths and the official building register, we employ a set of rules and functions to deduce the exposure, vulnerability and risk for each building. A risk indicator for each building, expressed as the expected damage associated to a given event, is derived by combining the building value and its vulnerability. (iii) The object-based hazards, exposures, vulnerabilities and risks can be scaled to any spatial unit desired. For this purpose we have developed an automated work flow building on the Python programming language in combination with ArcGIS and the R statistical software. This enables us to easily adapt the resulting risk indication maps to different zooming levels; to build statistics for various types of units; to flexibly react to the needs of the end users; and to account for the availability of reference data for validation. In the present study, we scale the results to the level of postal code zones. The evaluation of the results is based on loss reports of an insurance company and on photographs and videos obtained from various sources. We show a potential of the suggested work flow to reproduce the documented damages at the level of postal code zones. However, the results are very sensitive to the input parameters and model assumptions, and a robust back-calculation even of well-documented events remains a major challenge. Ultimately, we aim at integrating the procedure presented in a work flow for generating risk indication maps for pluvial flooding throughout the entire territory of Austria.

A Library of Rad Hard Mixed-Voltage/Mixed-Signal Building Blocks for Integration of Avionics Systems for Deep Space

NASA Technical Reports Server (NTRS)

Mojarradi, M. M.; Blaes, B.; Kolawa, E. A.; Blalock, B. J.; Li, H. W.; Buck, K.; Houge, D.

2001-01-01

To build the sensor intensive system-on-a-chip for the next generation spacecrafts for deep space, Center for Integration of Space Microsystems at JPL (CISM) takes advantage of the lower power rating and inherent radiation resistance of Silicon on Insulator technology (SOI). We are developing a suite of mixed-voltage and mixed-signal building blocks in Honeywell's SOI process that can enable the rapid integration of the next generation avionics systems with lower power rating, higher reliability, longer life, and enhanced radiation tolerance for spacecrafts such as the Europa Orbiter and Europa Lander. The mixed-voltage building blocks are predominantly for design of adaptive power management systems. Their design centers around an LDMOS structure that is being developed by Honeywell, Boeing Corp, and the University of Idaho. The mixed-signal building blocks are designed to meet the low power, extreme radiation requirement of deep space applications. These building blocks are predominantly used to interface analog sensors to the digital CPU of the next generation avionics system on a chip. Additional information is contained in the original extended abstract.

Single Molecule Conductance of Oligothiophene Derivatives

NASA Astrophysics Data System (ADS)

Dell, Emma J.

This thesis studies the electronic properties of small organic molecules based on the thiophene motif. If we are to build next-generation devices, advanced materials must be designed which possess requisite electronic functionality. Molecules present attractive candidates for these ad- vanced materials since nanoscale devices are particularly sought after. However, selecting a molecule that is suited to a certain electronic function remains a challenge, and characterization of electronic behavior is therefore critical. Single molecule conductance measurements are a powerful tool to determine properties on the nanoscale and, as such, can be used to investigate novel building blocks that may fulfill the design requirements of next-generation devices. Combining these conductance results with strategic chemical synthesis allows for the development of new families of molecules that show attractive properties for future electronic devices. Since thiophene rings are the fruitflies of organic semiconductors on the bulk scale, they present an intriguing starting point for building functional materials on the nanoscale, and therefore form the structural basis of all molecules studied herein. First, the single-molecule conductance of a family of bithiophene derivatives was measured. A broad distribution in the single-molecule conductance of bithiophene was found compared with that of a biphenyl. This increased breadth in the conductance distribution was shown to be explained by the difference in 5-fold symmetry of thiophene rings as compared to the 6-fold symmetry of benzene rings. The reduced symmetry of thiophene rings results in a restriction on the torsion angle space available to these molecules when bound between two metal electrodes in a junction, causing each molecular junction to sample a different set of conformers in the conductance measurements. By contrast, the rotations of biphenyl are essentially unimpeded by junction binding, allowing each molecular junction to sample similar conformers. This work demonstrates that the conductance of bithiophene displays a strong dependence on the conformational fluctuations accessible within a given junction configuration, and that the symmetry of such small molecules can significantly influence their conductance behavior. Next, the single-molecule conductance of a family of oligothiophenes comprising one to six thiophene units was measured. An anomalous behavior was found: the peak of the conductance histogram distribution did not follow a clear exponential decay with increasing number of thiophene units in the chain. The electronic properties of the materials were characterized by optical spectroscopy and electrochemistry to gain an understanding of the factors affecting the conductance of these molecules. Different conformers in the junction were postulated to be a contributing factor to the anomalous trend in the observed conductance as a function of molecule length. Then, the electronic properties of the thiophene-1,1-dioxide unit were investigated. These motifs have become synthetically accessible in the last decade, due to Rozen's unprecedentedly potent oxidizing reagent - HOF˙CH 3CN - which has been shown to be powerful yet selective enough to oxidize thiophenes in various environments. The resulting thiophene-1,1-dioxides show great promise for electronic devices. The oxidation chemistry of thiophenes was expanded and tuning of the frontier energy levels was demonstrated through combining electron poor and electron rich units. Finally, charge carriers in single-molecule junctions were shown to be tunable within a family of molecules containing these thiophene-1,1-dioxide (TDO) building blocks. Oligomers of TDO were designed in order to increase electron affinity, maintain delocalized frontier orbitals, while significantly decreasing the transport gap. Through thermopower measurements, the dominant charge carriers were shown to change from holes to electrons as the number of TDO units was increased. This resulted in a unique system in which the charge carrier depends on backbone length, providing a new means to tune p- and n-type transport in organic materials. Taken together, the results presented in this thesis offer an insight into how molecular symme- try and the accessible conformers within a junction have important consequences on conductance behavior. Additionally, thiophene-1,1-dioxide is shown to be an exciting unit for single molecule devices, especially when combined with electron rich thiophene flanking groups. By demon- strating, for the first time, a change in conductance pathway with molecular length, this work provides a framework for using frontier orbital levels to strategically design electronic building blocks.

Combined Heat & Power Using the Infinia Concentrated Solar CHP PowerDish System

DTIC Science & Technology

2013-08-01

been due to a temperature induced reduction in magnetic field strength (inside the generator) that in turn can cause a generator over-stroke which can... Measurements and Sensors 34 Table 4: Results Summary Performance Objectives (same as Table 2) 38 Table 5: Building 9246 Energy Consumption vs...and Building Measurement Instrumentation P&ID 28 Figure 12: Building 9246 Radiant Heating and Hot Water Equipment 29 Figure 13: Coolant Flow

Portable Mass Spectrometer Applications for In Situ Environmental Gas Monitoring

NASA Technical Reports Server (NTRS)

Griffin, Timothy P.; Diaz, J. Andres; Arkin, C. Richard; Conejo, Elian

2005-01-01

Primary Goal of this project is to (1) Design/build a flexible system to monitor air contamination (2) Learn requirements for operating system in low pressure and low temperature environments (3) Design/build system for integration into aircraft and automobiles Secondary Goals/Offshoots are (1) Fly aboard different aircraft (2)Hand-carry unit (3) Drive unit in automobiles.

Solar Water Heater Systems for Building Trades Class.

ERIC Educational Resources Information Center

Ryan, Milton; And Others

This teaching unit serves as a guide for the installation of active solar water heating systems. It contains a project designed for use with secondary level students of a building trades class. Students typically would meet 2 to 3 hours per day and would be able to complete the activity within a 1-week time period. Objectives of this unit include:…

To designate the Federal building and United States courthouse located at 224 South Boulder Avenue in Tulsa, Oklahoma, as the "H. Dale Cook Federal Building and United States Courthouse".

THOMAS, 111th Congress

Rep. Sullivan, John [R-OK-1

2009-07-23

Senate - 11/18/2009 Received in the Senate and Read twice and referred to the Committee on Environment and Public Works. (All Actions) Tracker: This bill has the status Passed HouseHere are the steps for Status of Legislation:

A bill to designate the Federal building and United States courthouse located at 1300 Victoria Street in Laredo, Texas, as the "George P. Kazen Federal Building and United States Courthouse".

THOMAS, 111th Congress

Rep. Cuellar, Henry [D-TX-28

2009-05-14

Senate - 10/15/2009 Received in the Senate and Read twice and referred to the Committee on Environment and Public Works. (All Actions) Tracker: This bill has the status Passed HouseHere are the steps for Status of Legislation:

Naphthobischalcogenadiazole Conjugated Polymers: Emerging Materials for Organic Electronics.

PubMed

Osaka, Itaru; Takimiya, Kazuo

2017-07-01

π-Conjugated polymers are an important class of materials for organic electronics. In the past decade, numerous polymers with donor-acceptor molecular structures have been developed and used as the active materials for organic devices, such as organic field-effect transistors (OFETs) and organic photovoltaics (OPVs). The choice of the building unit is the primary step for designing the polymers. Benzochalcogenadiazoles (BXzs) are one of the most familiar acceptor building units studied in this area. As their doubly fused system, naphthobischalcogenadiazoles (NXzs), i.e., naphthobisthiadiazole (NTz), naphthobisoxadiazole (NOz), and naphthobisselenadiazole (NSz) are emerging building units that provide interesting electronic properties and highly self-assembling nature for π-conjugated polymers. With these fruitful features, π-conjugated polymers based on these building units demonstrate great performances in OFETs and OPVs. In particular, in OPVs, NTz-based polymers have exhibited more than 10% efficiency, which is among the highest values reported so far. In this Progress Report, the synthesis, properties, and structures of NXzs and their polymers is summarized. The device performance is also highlighted and the structure-property relationships of the polymers are discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enabling Efficient, Responsive, and Resilient Buildings: Collaboration Between the United States and India

DOE Office of Scientific and Technical Information (OSTI.GOV)

Basu, Chandrayee; Ghatikar, Girish

The United States and India have among the largest economies in the world, and they continue to work together to address current and future challenges in reliable electricity supply. The acceleration to efficient, grid-responsive, resilient buildings represents a key energy security objective for federal and state agencies in both countries. The weaknesses in the Indian grid system were manifest in 2012, in the country’s worst blackout, which jeopardized the lives of half of India’s 1.2 billion people. While both countries are investing significantly in power sector reform, India, by virtue of its colossal growth rate in commercial energy intensity andmore » commercial floor space, is better placed than the United States to integrate and test state-of-art Smart Grid technologies in its future grid-responsive commercial buildings. This paper presents a roadmap of technical collaboration between the research organizations, and public-private stakeholders in both countries to accelerate the building-to-grid integration through pilot studies in India.« less

a New Mask for Automatic Building Detection from High Density Point Cloud Data and Multispectral Imagery

NASA Astrophysics Data System (ADS)

Awrangjeb, M.; Siddiqui, F. U.

2017-11-01

In complex urban and residential areas, there are buildings which are not only connected with and/or close to one another but also partially occluded by their surrounding vegetation. Moreover, there may be buildings whose roofs are made of transparent materials. In transparent buildings, there are point returns from both the ground (or materials inside the buildings) and the rooftop. These issues confuse the previously proposed building masks which are generated from either ground points or non-ground points. The normalised digital surface model (nDSM) is generated from the non-ground points and usually it is hard to find individual buildings and trees using the nDSM. In contrast, the primary building mask is produced using the ground points, thereby it misses the transparent rooftops. This paper proposes a new building mask based on the non-ground points. The dominant directions of non-ground lines extracted from the multispectral imagery are estimated. A dummy grid with the target mask resolution is rotated at each dominant direction to obtain the corresponding height values from the non-ground points. Three sub-masks are then generated from the height grid by estimating the gradient function. Two of these sub-masks capture planar surfaces whose height remain constant in along and across the dominant direction, respectively. The third sub-mask contains only the flat surfaces where the height (ideally) remains constant in all directions. All the sub-masks generated in all estimated dominant directions are combined to produce the candidate building mask. Although the application of the gradient function helps in removal of most of the vegetation, the final building mask is obtained through removal of planar vegetation, if any, and tiny isolated false candidates. Experimental results on three Australian data sets show that the proposed method can successfully remove vegetation, thereby separate buildings from occluding vegetation and detect buildings with transparent roof materials. While compared to existing building detection techniques, the proposed technique offers higher objectbased completeness, correctness and quality, specially in complex scenes with aforementioned issues. It is not only capable of detecting transparent buildings, but also small garden sheds which are sometimes as small as 5 m2 in area.

Finding New Water: Development of On-Site Non-Potable Water Reuse Systems

EPA Science Inventory

By designing our buildings to collect and treat water generated on-site, can be and reused for flushing our toilets and irrigating our landscaping. Several water sources are generated with-in a building including: rainwater, stormwater, graywater, blackwater and foundation drain...

22 CFR 1103.170 - Compliance procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Foreign Relations INTERNATIONAL BOUNDARY AND WATER COMMISSION, UNITED STATES AND MEXICO, UNITED STATES... INTERNATIONAL BOUNDARY AND WATER COMMISSION, UNITED STATES AND MEXICO, UNITED STATES SECTION § 1103.170... Mexico, United States Section, The Commons, Building C, Suite 310, 4171 North Mesa, El Paso, Texas 79902...

38 CFR 39.62 - Space criteria for support facilities.

Code of Federal Regulations, 2011 CFR

2011-07-01

... assignment for the next 10 years. (a) Administrative building. The administrative building should be.../office/equipment/work area); (5) Family/conference room; (6) Military honors team; (7) Refreshment unit; (8) Housekeeping aide's closet; and (9) Restroom facilities. (b) Maintenance/service building. The...

38 CFR 39.62 - Space criteria for support facilities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 10 years. (a) Administrative building. The administrative building should be approximately 1,600 NSF.../work area); (5) Family/conference room; (6) Military honors team; (7) Refreshment unit; (8) Housekeeping aide's closet; and (9) Restroom facilities. (b) Maintenance/service building. The maintenance...

78 FR 32365 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-30

...: National Institute of Standards and Technology (NIST). Title: Research on Evacuating Persons with Mobility... understanding of how building occupants with mobility impairments currently evacuate multi-story buildings in... in charge of developing emergency procedures for multi-story buildings in the United States...

Wood as a sustainable building material

Treesearch

Robert H. Falk

2009-01-01

Few building materials possess the environmental benefits of wood. It is not only the most widely used building material in the United States but also one with characteristics that make it suitable for a wide range of applications. Efficient, durable, and useful wood products produced from trees range from a minimally processed log at a log-home building site to a...

A profile of wood use in nonresidential building construction

Treesearch

H. N. Spelter; R. G. Anderson

This report presents estimates of the amounts of lumber, glued-laminated lumber, trusses, plywood, particleboard, hardboard, and wood shingles used in new nonresidential building construction in the United States. Use of wood products is shown for several building types, project sizes, and building components. The estimates are based on a survey of 489 projects under...

Cluster Organic Frameworks Constructed from Heterometallic Supertetrahedral Cluster Secondary Building Units.

PubMed

Lin, Li-Dan; Li, Xin-Xiong; Qi, Yan-Jie; Ma, Xiang; Zheng, Shou-Tian

2017-04-17

The two novel cluster organic frameworks based on heterometallic supertetrahedral cluster secondary building units (SBUs) [Cd 4 Cu 6 (L) 4 (Ac) 7 (H 2 O) 4 ](Ac)·7H 2 O (1) and [Mn 4 Cu 6 (L) 4 (Ac) 4.5 (H 2 O) 9 ]CuCN(Ac) 3.5 ·H 2 O (2), where H 3 L = 2-(hydroxymethyl)-2-(pyridin-4-yl)-1,3-propanediol and Ac = CH 3 COO - , have been prepared under solvothermal conditions. 1 and 2 are the first cases of cluster organic frameworks containing Cd-Cu/Mn-Cu heterometallic supertetrahedral cluster SBUs. Furthermore, 1 and 2 show an integration of magnetic properties and adsorption properties from both the heterometallic cluster secondary building units and the framework in a porous material.

Country Report on Building Energy Codes in Australia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shui, Bin; Evans, Meredydd; Somasundaram, Sriram

2009-04-02

This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America (U.S.). This reports gives an overview of the development of building energy codes in Australia, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, and lighting) for commercial and residential buildings in Australia.

Energy Efficient Building Management | Climate Neutral Research Campuses |

Science.gov Websites

NREL Efficient Building Management Energy Efficient Building Management As campuses complete generate the greatest climate impact. Energy efficient management in the existing stock of buildings is the following links go to sections that describe how an energy buildings management and maintenance program may

RCRA, superfund and EPCRA hotline training module. Introduction to: Containment buildings (40 cfr parts 264/265, subpart dd) updated July 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-07-01

The module outlines the regulatory history and purpose of containment buildings. It disucsses the relationship between LDR and containment buildings. It summarizes the design and operating standard applicable to containment buildings and describes the relationship between generator accumulation standards and containment buildings.

Experimental shielding evaluation of the radiation protection provided by the structurally significant components of residential structures.

PubMed

Dickson, E D; Hamby, D M

2014-03-01

The human health and environmental effects following a postulated accidental release of radioactive material to the environment have been a public and regulatory concern since the early development of nuclear technology. These postulated releases have been researched extensively to better understand the potential risks for accident mitigation and emergency planning purposes. The objective of this investigation is to provide an updated technical basis for contemporary building shielding factors for the US housing stock. Building shielding factors quantify the protection from ionising radiation provided by a certain building type. Much of the current data used to determine the quality of shielding around nuclear facilities and urban environments is based on simplistic point-kernel calculations for 1950s era suburbia and is no longer applicable to the densely populated urban environments realised today. To analyse a building's radiation shielding properties, the ideal approach would be to subject a variety of building types to various radioactive sources and measure the radiation levels in and around the building. While this is not entirely practicable, this research analyses the shielding effectiveness of ten structurally significant US housing-stock models (walls and roofs) important for shielding against ionising radiation. The experimental data are used to benchmark computational models to calculate the shielding effectiveness of various building configurations under investigation from two types of realistic environmental source terms. Various combinations of these ten shielding models can be used to develop full-scale computational housing-unit models for building shielding factor calculations representing 69.6 million housing units (61.3%) in the United States. Results produced in this investigation provide a comparison between theory and experiment behind building shielding factor methodology.

Field Evaluation of the Performance of the RTU Challenge Unit: Daikin Rebel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katipamula, Srinivas; Wang, W.; Ngo, Hung

2017-05-31

Packaged rooftop air-conditioning units (RTUs) are used in 44% (2.5 million) of all commercial buildings, serving over 57% (46 billion square feet) of the commercial building floor space in the United States (EIA 2012). The primary energy consumption associated with RTUs is over 2.2 quads annually. Therefore, even a small improvement in efficiency or part-load operation of these units can lead to significant reductions in energy use and carbon emissions. Starting in 2011, the U.S. Department of Energy’s (DOE’s) Building Technologies Office funded a series of projects related to RTUs. Some projects were intended to improve the operating efficiency ofmore » the existing RTUs, while others were focused on improving the operating efficiency of new units. This report documents the field-testing and comparison of the seasonal efficiency of a state-of-art RTU Challenge unit and a standard unit. Section II provides the background for the work. Section III describes the measurement and verification plan for the field tests. Section IV describes the measurement and verification evaluation plan. The results are described in Section V. The lessons learned and recommendations for future work are presented in Section VI. A list of references is provided in Section VII.« less

The extent of food waste generation across EU-27: different calculation methods and the reliability of their results.

PubMed

Bräutigam, Klaus-Rainer; Jörissen, Juliane; Priefer, Carmen

2014-08-01

The reduction of food waste is seen as an important societal issue with considerable ethical, ecological and economic implications. The European Commission aims at cutting down food waste to one-half by 2020. However, implementing effective prevention measures requires knowledge of the reasons and the scale of food waste generation along the food supply chain. The available data basis for Europe is very heterogeneous and doubts about its reliability are legitimate. This mini-review gives an overview of available data on food waste generation in EU-27 and discusses their reliability against the results of own model calculations. These calculations are based on a methodology developed on behalf of the Food and Agriculture Organization of the United Nations and provide data on food waste generation for each of the EU-27 member states, broken down to the individual stages of the food chain and differentiated by product groups. The analysis shows that the results differ significantly, depending on the data sources chosen and the assumptions made. Further research is much needed in order to improve the data stock, which builds the basis for the monitoring and management of food waste. © The Author(s) 2014.

Using SW4 for 3D Simulations of Earthquake Strong Ground Motions: Application to Near-Field Strong Motion, Building Response, Basin Edge Generated Waves and Earthquakes in the San Francisco Bay Are

NASA Astrophysics Data System (ADS)

Rodgers, A. J.; Pitarka, A.; Petersson, N. A.; Sjogreen, B.; McCallen, D.; Miah, M.

2016-12-01

Simulation of earthquake ground motions is becoming more widely used due to improvements of numerical methods, development of ever more efficient computer programs (codes), and growth in and access to High-Performance Computing (HPC). We report on how SW4 can be used for accurate and efficient simulations of earthquake strong motions. SW4 is an anelastic finite difference code based on a fourth order summation-by-parts displacement formulation. It is parallelized and can run on one or many processors. SW4 has many desirable features for seismic strong motion simulation: incorporation of surface topography; automatic mesh generation; mesh refinement; attenuation and supergrid boundary conditions. It also has several ways to introduce 3D models and sources (including Standard Rupture Format for extended sources). We are using SW4 to simulate strong ground motions for several applications. We are performing parametric studies of near-fault motions from moderate earthquakes to investigate basin edge generated waves and large earthquakes to provide motions to engineers study building response. We show that 3D propagation near basin edges can generate significant amplifications relative to 1D analysis. SW4 is also being used to model earthquakes in the San Francisco Bay Area. This includes modeling moderate (M3.5-5) events to evaluate the United States Geologic Survey's 3D model of regional structure as well as strong motions from the 2014 South Napa earthquake and possible large scenario events. Recently SW4 was built on a Commodity Technology Systems-1 (CTS-1) at LLNL, new systems for capacity computing at the DOE National Labs. We find SW4 scales well and runs faster on these systems compared to the previous generation of LINUX clusters.

Test Hardware Design for Flightlike Operation of Advanced Stirling Convertors (ASC-E3)

NASA Technical Reports Server (NTRS)

Oriti, Salvatore M.

2012-01-01

NASA Glenn Research Center (GRC) has been supporting development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG project is providing life, reliability, and performance testing of the Advanced Stirling Convertor (ASC). For this purpose, the Thermal Energy Conversion branch at GRC has been conducting extended operation of a multitude of free-piston Stirling convertors. The goal of this effort is to generate long-term performance data (tens of thousands of hours) simultaneously on multiple units to build a life and reliability database. The test hardware for operation of these convertors was designed to permit in-air investigative testing, such as performance mapping over a range of environmental conditions. With this, there was no requirement to accurately emulate the flight hardware. For the upcoming ASC-E3 units, the decision has been made to assemble the convertors into a flight-like configuration. This means the convertors will be arranged in the dual-opposed configuration in a housing that represents the fit, form, and thermal function of the ASRG. The goal of this effort is to enable system level tests that could not be performed with the traditional test hardware at GRC. This offers the opportunity to perform these system-level tests much earlier in the ASRG flight development, as they would normally not be performed until fabrication of the qualification unit. This paper discusses the requirements, process, and results of this flight-like hardware design activity.

Test Hardware Design for Flight-Like Operation of Advanced Stirling Convertors

NASA Technical Reports Server (NTRS)

Oriti, Salvatore M.

2012-01-01

NASA Glenn Research Center (GRC) has been supporting development of the Advanced Stirling Radioisotope Generator (ASRG) since 2006. A key element of the ASRG project is providing life, reliability, and performance testing of the Advanced Stirling Convertor (ASC). For this purpose, the Thermal Energy Conversion branch at GRC has been conducting extended operation of a multitude of free-piston Stirling convertors. The goal of this effort is to generate long-term performance data (tens of thousands of hours) simultaneously on multiple units to build a life and reliability database. The test hardware for operation of these convertors was designed to permit in-air investigative testing, such as performance mapping over a range of environmental conditions. With this, there was no requirement to accurately emulate the flight hardware. For the upcoming ASC-E3 units, the decision has been made to assemble the convertors into a flight-like configuration. This means the convertors will be arranged in the dual-opposed configuration in a housing that represents the fit, form, and thermal function of the ASRG. The goal of this effort is to enable system level tests that could not be performed with the traditional test hardware at GRC. This offers the opportunity to perform these system-level tests much earlier in the ASRG flight development, as they would normally not be performed until fabrication of the qualification unit. This paper discusses the requirements, process, and results of this flight-like hardware design activity.

Moon Munchies: Human Exploration Project Engineering Design Challenge--A Standards-Based Elementary School Model Unit Guide--Design, Build, and Evaluate (Lessons 1-6). Engineering By Design: Advancing Technological Literacy--A Standards-Based Program Series. EP-2007-08-92-MSFC

ERIC Educational Resources Information Center

Weaver, Kim M.

2005-01-01

In this unit, elementary students design and build a lunar plant growth chamber using the Engineering Design Process. The purpose of the unit is to help students understand and apply the design process as it relates to plant growth on the moon. This guide includes six lessons, which meet a number of national standards and benchmarks in…

EXTERIOR ELEVATIONS. United Engineering Company Ltd., Alameda Shipyard, Ship Repair ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EXTERIOR ELEVATIONS. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities, Office Building. Includes lettering detail for front elevation. John Hudspeth, Architect, at foot of Main Street, Alameda, Calif. Sheet no. A3 of 8 sheets, Plan no. 10,007. Scale 1/8 inch to the foot. March 18, 1942, last revised 9/21/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Office Building No. 137, 2900 Main Street, Alameda, Alameda County, CA

SECOND FLOOR AND ROOF PLANS. United Engineering Company Ltd., Alameda ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SECOND FLOOR AND ROOF PLANS. United Engineering Company Ltd., Alameda Shipyard, Ship Repair Facilities, Office Building. Second floor plan, and roof plan. John Hudspeth, Architect, at foot of Main Street, Alameda, Calif. Sheet no. A2 of 8 sheets, Plan no. 10,007. Scale 1/8 inch to the foot. March 18, 1942, last revised 9/22/43. U.S. Navy, Bureau of Yards & Docks, Contract no. bs 76. Approved for construction October 9, 1943. blueprint - United Engineering Company Shipyard, Office Building No. 137, 2900 Main Street, Alameda, Alameda County, CA

Growth, chamber building rate and reproduction time of Palaeonummulites venosus under natural conditions.

NASA Astrophysics Data System (ADS)

Kinoshita, Shunichi; Eder, Wolfgang; Wöger, Julia; Hohenegger, Johann; Briguglio, Antonino

2017-04-01

Investigations on Palaeonummulites venosus using the natural laboratory approach for determining chamber building rate, test diameter increase rate, reproduction time and longevity is based on the decomposition of monthly obtained frequency distributions based on chamber number and test diameter into normal-distributed components. The shift of the component parameters 'mean' and 'standard deviation' during the investigation period of 15 months was used to calculate Michaelis-Menten functions applied to estimate the averaged chamber building rate and diameter increase rate under natural conditions. The individual dates of birth were estimated using the inverse averaged chamber building rate and the inverse diameter increase rate fitted by the individual chamber number or the individual test diameter at the sampling date. Distributions of frequencies and densities (i.e. frequency divided by sediment weight) based on chamber building rate and diameter increase rate resulted both in a continuous reproduction through the year with two peaks, the stronger in May /June determined as the beginning of the summer generation (generation1) and the weaker in November determined as the beginning of the winter generation (generation 2). This reproduction scheme explains the existence of small and large specimens in the same sample. Longevity, calculated as the maximum difference in days between the individual's birth date and the sampling date seems to be round about one year, obtained by both estimations based on the chamber building rate and the diameter increase rate.

Technology Solutions Case Study: Retrofit Measures for Embedded Wood Members in Insulated Mass Masonry Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

K. Ueno

2015-10-01

In this project, the Building Science Corporation team studied a historic brick building in Lawrence, Massachusetts, which is being renovated into 10 condominium units and adding insulation to the interior side of walls of such masonry buildings.

GPS in pioneering dynamic monitoring of long-period structures

USGS Publications Warehouse

Celebi, M.; Sanli, A.

2002-01-01

Global Positioning System (GPS) technology with 10-20-Hz sampling rates allows scientifically justified dynamic measurements of relative displacements of long-period structures. The displacement response of a simulated tall building in real time and permanent deployment of GPS units at the roof of a building are described. To the authors' best knowledge, this is the first permanent deployment of GPS units (in the world) for continuous dynamic monitoring of a tall building. Data recorded from the building during a windy day is analyzed to determine the structural characteristics. When recorded during extreme motions caused by earthquakes and strong winds, such measurements can be used to compute average drift ratios and changes in dynamic characteristics, and therefore can be used by engineers and building owners or managers to assess the structural integrity and performance by establishing pre-established thresholds. Such information can be used to secure public safety and/or take steps to improve the performance of the building.

Green Building Implementation at Schools in North Sulawesi, Indonesia

NASA Astrophysics Data System (ADS)

Harimu, D. A. J.; Tumanduk, M. S. S. S.

2018-02-01

This research aims at investigating the green building implementation at schools in North Sulawesi, Indonesia; and to analysis the relationship between implementation of green building concept at school with students’ green behaviour. This research is Survey Research with quantitative descriptive method. The analysis unit is taken purposively, that is school that had been implemented the green building concept, Manado’s 3rd Public Vocational High School, Lokon High School at Tomohon, Manado Independent School at North Minahasa, and Tondano’s 3rd Public Vocational High School. Data collecting is acquired by observation and questionnaire. The Assessment Criteria of green building on Analysis Unit, is taken from Greenship Existing Building ver 1. There are 4 main points that being assessed, which are Energy Conservation and Efficiency; Water Conservation; Indoor Health and Comfort; Waste Managerial. The Analysis technique used in this research is the simple regression analysis. The result of the research shows that there is a significant relation between green building implementation at school and students’ green behavior. The result is accordance with the Gesalts Psychologist theories, that architecture can change the user’s behaviour.

Building Community Bonds, Bridges, and Linkages to Promote the Career Readiness of High School Students in the United States

ERIC Educational Resources Information Center

Hernandez-Gantes, Victor M.; Keighobadi, Sasha; Fletcher, Edward C., Jr.

2018-01-01

The career readiness of high school students has been a longstanding issue that has received renewed attention in recent years. To document an approach to promoting career readiness in the United States, we conducted an exploratory case study of a distinguished information technology career academy. Using the premises of capital building as a…

48 CFR 3036.104-90 - Authority for one-step turn-key design-build contracting for the United States Coast Guard (USCG).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 7 2014-10-01 2014-10-01 false Authority for one-step turn-key design-build contracting for the United States Coast Guard (USCG). 3036.104-90 Section 3036.104-90 Federal Acquisition Regulations System DEPARTMENT OF HOMELAND SECURITY, HOMELAND SECURITY ACQUISITION REGULATION (HSAR) SPECIAL CATEGORIES OF...

Crowning the Cathedral of Florence: Brunelleschi Builds His Dome. A Unit of Study for Grades 7-10.

ERIC Educational Resources Information Center

Symcox, Linda

This unit focuses on a dramatic moment in the Renaissance from about 1420 when Filippo Brunelleschi single handedly created, defined, and engineered a new architecture by building the great dome of the cathedral of Santa Maria del Fiore in Florence. The dome became the symbol of Florence's grandeur during the Renaissance, and a model for great…

Gaseous Elemental Mercury and Total and Leached Mercury in Building Materials from the Former Hg-Mining Area of Abbadia San Salvatore (Central Italy).

PubMed

Vaselli, Orlando; Nisi, Barbara; Rappuoli, Daniele; Cabassi, Jacopo; Tassi, Franco

2017-04-15

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic, and it represents a pollutant of global concern. Liquid Hg is highly volatile and can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study, the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paint, plaster, roof tiles, concrete, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into seven units) covers a surface of about 65 ha and contains mining structures and managers' and workers' buildings. Nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in Units 2, 3 and 6, the latter being the area where liquid mercury was produced. Measurements were also performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in time and space mostly depending on ambient temperature and the operational activities that were carried out in each building. The Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng·m -3 , while in Unit 6, they were on average much higher, and occasionally, they saturated the GEM measurement device (>50,000 ng·m -3 ). Concentrations of total (in mg·kg -1 ) and leached (in μg·L -1 ) mercury measured in different building materials (up to 46,580 mg·kg -1 and 4470 mg·L -1 , respectively) were highly variable, being related to the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for operational cleanings to be carried out during reclamation activities.

Commercialization and internationalization of the next-generation launch system

NASA Astrophysics Data System (ADS)

Bille, Matthew A.; Richie, George E.; Bille, Deborah A.

1996-03-01

The United States, ESA, Russia, and Japan are all pursuing the goal of a next-generation launch system. However, economic constraints may ground these programs, as they did hypersonic spaceplane efforts. In today's constrained fiscal environment, engineering is secondary unless the most practical economic and political approach is also found. While international efforts face national concerns over jobs and competitiveness, low-cost access to orbit will open up space to whole new industries. In the long run, all involved nations will gain economically if a next-generation launcher is built, and all will lose if individual efforts fail. An international consortium is most likely to amass the resources needed. The consortium would not be dedicated to any single technical concept, but would select from industry proposals to design and build the technology demonstrator. The goal is to get one working system built: after that, it is not critical whether we have one cooperative operational system or a dozen competing ones. What is critical is not to miss another chance to launch the era of space commercialization.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakafuji, Dora; Gouveia, Lauren

This project supports development of the next generation, integrated energy management infrastructure (EMS) able to incorporate advance visualization of behind-the-meter distributed resource information and probabilistic renewable energy generation forecasts to inform real-time operational decisions. The project involves end-users and active feedback from an Utility Advisory Team (UAT) to help inform how information can be used to enhance operational functions (e.g. unit commitment, load forecasting, Automatic Generation Control (AGC) reserve monitoring, ramp alerts) within two major EMS platforms. Objectives include: Engaging utility operations personnel to develop user input on displays, set expectations, test and review; Developing ease of use and timelinessmore » metrics for measuring enhancements; Developing prototype integrated capabilities within two operational EMS environments; Demonstrating an integrated decision analysis platform with real-time wind and solar forecasting information and timely distributed resource information; Seamlessly integrating new 4-dimensional information into operations without increasing workload and complexities; Developing sufficient analytics to inform and confidently transform and adopt new operating practices and procedures; Disseminating project lessons learned through industry sponsored workshops and conferences;Building on collaborative utility-vendor partnership and industry capabilities« less

Disposal of Kitchen Waste from High Rise Apartment

NASA Astrophysics Data System (ADS)

Ori, Kirki; Bharti, Ajay; Kumar, Sunil

2017-09-01

The high rise building has numbers of floor and rooms having variety of users or tenants for residential purposes. The huge quantities of heterogenous mixtures of domestic food waste are generated from every floor of the high rise residential buildings. Disposal of wet and biodegradable domestic kitchen waste from high rise buildings are more expensive in regards of collection and vertical transportation. This work is intended to address the technique to dispose of the wet organic food waste from the high rise buildings or multistory building at generation point with the advantage of gravity and vermicomposting technique. This innovative effort for collection and disposal of wet organic solid waste from high rise apartment is more economical and hygienic in comparison with present system of disposal.

78 FR 65639 - Questar Pipeline Company; Notice of Request Under Blanket Authorization

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-01

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. CP14-6-000] Questar Pipeline... appurtenant facilities located in Moffat County, Colorado. Specifically, Questar proposes to abandon one Solar Saturn 1200 compressor, a compressor building, two generators and a generator building, a liquids storage...

Mapping the impacts of thermoelectric power generation: a global, spatially explicit database

NASA Astrophysics Data System (ADS)

Raptis, Catherine; Pfister, Stephan

2017-04-01

Thermoelectric power generation is associated with environmental pressures resulting from emissions to air and water, as well as water consumption. The need to achieve global coverage in related studies has become pressing in view of climate change. At the same time, the ability to quantify impacts from power production on a high resolution remains pertinent, given their highly regionalized nature, particularly when it comes to water-related impacts. Efforts towards global coverage have increased in recent years, but most work on the impacts of global electricity production presents a coarse geographical differentiation. Over the past few years we have begun a concerted effort to create and make available a global georeferenced inventory of thermoelectric power plant operational characteristics and emissions, by modelling the relevant processes on the highest possible level: that of a generating unit. Our work extends and enhances a commercially available global power plant database, and so far includes: - Georeferencing the generating units and populating the gaps in their steam properties. - Identifying the cooling system for 92% of the global installed thermoelectric power capacity. - Using the completed steam property data, along with local environmental temperature data, to systematically solve the Rankine cycle for each generating unit, involving: i) distinguishing between simple, reheat, and cogenerative cycles, and accounting for particularities in nuclear power cycles; ii) accounting for the effect of different cooling systems (once-through, recirculating (wet tower), dry cooling) on the thermodynamic cycle. One of the direct outcomes of solving the Rankine cycle is the cycle efficiency, an indispensable parameter in any study related to power production, including the quantification of air emissions and water consumption. Another direct output, for those units employing once-through cooling, is the rate of heat rejection to water, which can lead to thermal pollution. The opportunities afforded by the creation of this comprehensive database are numerous, including its use in integrated studies of electricity production and environmental burden, on local or global scales. The quantification, on the highest possible geographical and technological resolution, of all the different current impacts caused by thermoelectric power generation is crucial in order to conduct a proper assessment of the trade-offs in impacts in future scenario studies including technological changes, and to avoid burden-shifting. Here, we present the progress made in the building of the database so far, as well as the results of its application in a worldwide study of the thermal stress of rivers from the heat rejected by power plants using once-through cooling systems.

Gossip and nurses: malady or remedy?

PubMed

Thomas, Sarah A; Rozell, Elizabeth J

2007-01-01

Gossip is a natural part of every social setting and has a profound influence on organizational behaviors. As the primary care givers in the hospital setting, nurses are the front line in generating and controlling gossip. It is essential that management recognize this dynamic in the nursing workforce so they can be proactive in developing strategies to effectively control gossip. This article highlights the positive and negative aspects of gossip and provides strategies to help nursing professionals effectively manage this workplace issue. Unmanaged gossip can have a negative effect on the workplace by damaging relationships and reputations. Gossip that is managed effectively can have a positive effect on the workplace by building social bonds within the nursing unit.

KSC-2009-1314

NASA Image and Video Library

2009-01-22

CAPE CANAVERAL, Fla. – Inside the Assembly and Refurbishment Facility at NASA's Kennedy Space Center in Florida, the Ares I-X forward skirt is lowered onto supports on the floor. United Space Alliance, under a subcontract to ATK, will complete the integration and assembly of the forward skirt components in the ARF. It will then be moved to the Vehicle Assembly Building high bay 3 for stacking operations. The forward skirt is the initial piece of first-stage hardware in preparation for the July 2009 test flight of the agency's next-generation spacecraft and launch vehicle system. Built entirely of armored steel, the 14,000-pound segment is seven feet tall and 12-1/4 feet wide. Photo credit: NASA/Kim Shiflett

NARMER-1: a photon point-kernel code with build-up factors

NASA Astrophysics Data System (ADS)

Visonneau, Thierry; Pangault, Laurence; Malouch, Fadhel; Malvagi, Fausto; Dolci, Florence

2017-09-01

This paper presents an overview of NARMER-1, the new generation of photon point-kernel code developed by the Reactor Studies and Applied Mathematics Unit (SERMA) at CEA Saclay Center. After a short introduction giving some history points and the current context of development of the code, the paper exposes the principles implemented in the calculation, the physical quantities computed and surveys the generic features: programming language, computer platforms, geometry package, sources description, etc. Moreover, specific and recent features are also detailed: exclusion sphere, tetrahedral meshes, parallel operations. Then some points about verification and validation are presented. Finally we present some tools that can help the user for operations like visualization and pre-treatment.

De novo assembly of human genomes with massively parallel short read sequencing.

PubMed

Li, Ruiqiang; Zhu, Hongmei; Ruan, Jue; Qian, Wubin; Fang, Xiaodong; Shi, Zhongbin; Li, Yingrui; Li, Shengting; Shan, Gao; Kristiansen, Karsten; Li, Songgang; Yang, Huanming; Wang, Jian; Wang, Jun

2010-02-01

Next-generation massively parallel DNA sequencing technologies provide ultrahigh throughput at a substantially lower unit data cost; however, the data are very short read length sequences, making de novo assembly extremely challenging. Here, we describe a novel method for de novo assembly of large genomes from short read sequences. We successfully assembled both the Asian and African human genome sequences, achieving an N50 contig size of 7.4 and 5.9 kilobases (kb) and scaffold of 446.3 and 61.9 kb, respectively. The development of this de novo short read assembly method creates new opportunities for building reference sequences and carrying out accurate analyses of unexplored genomes in a cost-effective way.

Exploring New Models for Utility Distributed Energy Resource Planning and Integration: SMUD and Con Edison

DOE Office of Scientific and Technical Information (OSTI.GOV)

2018-01-23

As a result of the rapid growth of renewable energy in the United States, the U.S. electric grid is undergoing a monumental shift away from its historical status quo. These changes are occurring at both the centralized and local levels and have been driven by a number of different factors, including large declines in renewable energy costs, federal and state incentives and mandates, and advances in the underlying technology. Higher levels of variable-generation renewable energy, however, may require new and increasingly complex methods for utilities to operate and maintain the grid while also attempting to limit the costly build-out ofmore » supporting grid infrastructure.« less

Exploitation of Digital Surface Models Generated from WORLDVIEW-2 Data for SAR Simulation Techniques

NASA Astrophysics Data System (ADS)

Ilehag, R.; Auer, S.; d'Angelo, P.

2017-05-01

GeoRaySAR, an automated SAR simulator developed at DLR, identifies buildings in high resolution SAR data by utilizing geometric knowledge extracted from digital surface models (DSMs). Hitherto, the simulator has utilized DSMs generated from LiDAR data from airborne sensors with pre-filtered vegetation. Discarding the need for pre-optimized model input, DSMs generated from high resolution optical data (acquired with WorldView-2) are used for the extraction of building-related SAR image parts in this work. An automatic preprocessing of the DSMs has been developed for separating buildings from elevated vegetation (trees, bushes) and reducing the noise level. Based on that, automated simulations are triggered considering the properties of real SAR images. Locations in three cities, Munich, London and Istanbul, were chosen as study areas to determine advantages and limitations related to WorldView-2 DSMs as input for GeoRaySAR. Beyond, the impact of the quality of the DSM in terms of building extraction is evaluated as well as evaluation of building DSM, a DSM only containing buildings. The results indicate that building extents can be detected with DSMs from optical satellite data with various success, dependent on the quality of the DSM as well as on the SAR imaging perspective.

International decade for natural disaster reduction

USGS Publications Warehouse

Hays, W. W.

1990-01-01

Throughout history, humanity has found itself in conflict with naturally occurring events of geologic, hydrologic, and atmospheric origin. this conflict has been demonstrated repeatedly when people build urban centers at the water's edge, in or near active fault systems capable of generating earthquakes, on steep slopes, near active volcanoes, or at the urban-wilderness interface prone to wildfires. Naturally occurring, recurrent events such as floods, windstorms, tsunamis, earthquakes, landslides, volcanic eruptions, and wildfires have tested human-engineered works many times and have often found them unable to withstand the forces generated by the event. In the past 20 years, for example, events like these throughout the world have claimed more than 2.8 million lives and adversely affected 820 million people; single disasters have caused economic losses of billions of dollars. Industrialized countries like the United States and Japan have been able to absorb the socioeconomic losses of past natural disasters, but the economics of many developing countries have been devastated by losses equal to a large percentage of their gross national product. Furthermore, the magnitude of the losses is increasing at a rapid rate as the building wealth of nations is expanded to meet the needs of rapidly increasing population, often without adequate consideration of the potential threat posed by the recurrent natural hazards and without implementing effective loss-reduction measures because of lack of knowledge or lack of technical capability. 

Building Momentum: National Trends and Prospects for High-Performance Green Buildings.

ERIC Educational Resources Information Center

2003

This report is an outgrowth of the Green Building Roundtable of the U.S. Senate Committee on Environment and Public Works held in conjunction with the U.S. Green Building Council on April 24, 2002. The roundtable brought together diverse interests to educate members of Congress on green building trends and generated discussion about the economic…

Building Trades 1. Course Outline.

ERIC Educational Resources Information Center

Hill, Clair S.

Intended to assist building trades instructors, this course outline to a prevocational building trades program for junior and senior high school students covers four occupational areas: carpentry, masonry, plumbing, and electricity. Specific notes to the administrator and teacher and the course goals precede the four occupational units. Each unit…

System to control contamination during retrieval of buried TRU waste

DOEpatents

Menkhaus, Daniel E.; Loomis, Guy G.; Mullen, Carlan K.; Scott, Donald W.; Feldman, Edgar M.; Meyer, Leroy C.

1993-01-01

A system to control contamination during the retrieval of hazardous waste comprising an outer containment building, an inner containment building, within the outer containment building, an electrostatic radioactive particle recovery unit connected to and in communication with the inner and outer containment buildings, and a contaminate suppression system including a moisture control subsystem, and a rapid monitoring system having the ability to monitor conditions in the inner and outer containment buildings.

System to control contamination during retrieval of buried TRU waste

DOEpatents

Menkhaus, D.E.; Loomis, G.G.; Mullen, C.K.; Scott, D.W.; Feldman, E.M.; Meyer, L.C.

1993-04-20

A system is described to control contamination during the retrieval of hazardous waste comprising an outer containment building, an inner containment building, within the outer containment building, an electrostatic radioactive particle recovery unit connected to and in communication with the inner and outer containment buildings, and a contaminate suppression system including a moisture control subsystem, and a rapid monitoring system having the ability to monitor conditions in the inner and outer containment buildings.

Hospital ships adrift? Part 2: the role of US Navy hospital ship humanitarian assistance missions in building partnerships.

PubMed

Licina, Derek; Mookherji, Sangeeta; Migliaccio, Gene; Ringer, Cheryl

2013-12-01

US Navy hospital ships are used as a foreign policy instrument to achieve various objectives that include building partnerships. Despite substantial resource investment by the Department of Defense (DoD) in these missions, their impact is unclear. The purpose of this study was to understand how and why hospital ship missions influence partnerships among the different participants. An embedded case study was used and included the hospital ship Mercy's mission to Timor-Leste in 2008 and 2010 with four units of analysis: the US government, partner nation, host nation, and nongovernmental organizations. Key stakeholders representing each unit were interviewed using open-ended questions that explored the experiences of each participant and their organization. Findings were analyzed using a priori domains from a proposed partnership theoretical framework. A documentary review of key policy, guidance, and planning documents was also conducted. Fifteen themes related to how and why hospital ship missions influence partnerships emerged from the 37 interviews and documentary review. The five most prominent included: developing relationships, developing new perspectives, sharing resources, understanding partner constraints, and developing credibility. Facilitators to joining the mission included partner nations seeking a regional presence and senior executive relationships. Enablers included historical relationships and host nation receptivity. The primary barrier to joining was the military leading the mission. Internal constraints included the short mission duration, participant resentment, and lack of personnel continuity. External constraints included low host nation and United States Agency for International Development (USAID) capacity. The research finds the idea of building partnerships exists among most units of analysis. However, the results show a delay in downstream effects of generating action and impact among the participants. Without a common partnership definition and policy, guidance, and planning documents reinforcing these constructs, achieving the partnership goal will remain challenging. Efforts should be made to magnify the facilitators and enablers while developing mitigation strategies for the barriers and constraints. This is the first study to scientifically assess the partnership impact of hospital ship missions and could support the DoD's effort to establish, enable, and sustain meaningful partnerships. Application of the findings to improve partnerships in contexts beyond hospital ship missions may be warranted and require further analysis. This unique opportunity could bridge the rift with humanitarian actors and establish, enable, and sustain meaningful partnerships with the DoD.

ATLAS software configuration and build tool optimisation

NASA Astrophysics Data System (ADS)

Rybkin, Grigory; Atlas Collaboration

2014-06-01

ATLAS software code base is over 6 million lines organised in about 2000 packages. It makes use of some 100 external software packages, is developed by more than 400 developers and used by more than 2500 physicists from over 200 universities and laboratories in 6 continents. To meet the challenge of configuration and building of this software, the Configuration Management Tool (CMT) is used. CMT expects each package to describe its build targets, build and environment setup parameters, dependencies on other packages in a text file called requirements, and each project (group of packages) to describe its policies and dependencies on other projects in a text project file. Based on the effective set of configuration parameters read from the requirements files of dependent packages and project files, CMT commands build the packages, generate the environment for their use, or query the packages. The main focus was on build time performance that was optimised within several approaches: reduction of the number of reads of requirements files that are now read once per package by a CMT build command that generates cached requirements files for subsequent CMT build commands; introduction of more fine-grained build parallelism at package task level, i.e., dependent applications and libraries are compiled in parallel; code optimisation of CMT commands used for build; introduction of package level build parallelism, i. e., parallelise the build of independent packages. By default, CMT launches NUMBER-OF-PROCESSORS build commands in parallel. The other focus was on CMT commands optimisation in general that made them approximately 2 times faster. CMT can generate a cached requirements file for the environment setup command, which is especially useful for deployment on distributed file systems like AFS or CERN VMFS. The use of parallelism, caching and code optimisation significantly-by several times-reduced software build time, environment setup time, increased the efficiency of multi-core computing resources utilisation, and considerably improved software developer and user experience.

Calibrating Building Energy Models Using Supercomputer Trained Machine Learning Agents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanyal, Jibonananda; New, Joshua Ryan; Edwards, Richard

2014-01-01

Building Energy Modeling (BEM) is an approach to model the energy usage in buildings for design and retrofit purposes. EnergyPlus is the flagship Department of Energy software that performs BEM for different types of buildings. The input to EnergyPlus can often extend in the order of a few thousand parameters which have to be calibrated manually by an expert for realistic energy modeling. This makes it challenging and expensive thereby making building energy modeling unfeasible for smaller projects. In this paper, we describe the Autotune research which employs machine learning algorithms to generate agents for the different kinds of standardmore » reference buildings in the U.S. building stock. The parametric space and the variety of building locations and types make this a challenging computational problem necessitating the use of supercomputers. Millions of EnergyPlus simulations are run on supercomputers which are subsequently used to train machine learning algorithms to generate agents. These agents, once created, can then run in a fraction of the time thereby allowing cost-effective calibration of building models.« less

Automatic generation of smart earthquake-resistant building system: Hybrid system of base-isolation and building-connection.

PubMed

Kasagi, M; Fujita, K; Tsuji, M; Takewaki, I

2016-02-01

A base-isolated building may sometimes exhibit an undesirable large response to a long-duration, long-period earthquake ground motion and a connected building system without base-isolation may show a large response to a near-fault (rather high-frequency) earthquake ground motion. To overcome both deficiencies, a new hybrid control system of base-isolation and building-connection is proposed and investigated. In this new hybrid building system, a base-isolated building is connected to a stiffer free wall with oil dampers. It has been demonstrated in a preliminary research that the proposed hybrid system is effective both for near-fault (rather high-frequency) and long-duration, long-period earthquake ground motions and has sufficient redundancy and robustness for a broad range of earthquake ground motions.An automatic generation algorithm of this kind of smart structures of base-isolation and building-connection hybrid systems is presented in this paper. It is shown that, while the proposed algorithm does not work well in a building without the connecting-damper system, it works well in the proposed smart hybrid system with the connecting damper system.

A novel power-efficient high-speed clock management unit using quantum-dot cellular automata

NASA Astrophysics Data System (ADS)

Abutaleb, M. M.

2017-04-01

Quantum-dot cellular automata (QCA) is one of the most attractive alternatives for complementary metal-oxide semiconductor technology. The QCA widely supports a new paradigm in the field of nanotechnology that has the potential for high density, low power, and high speed. The clock manager is an essential building block in the new microwave and radio frequency integrated circuits. This paper describes a novel QCA-based clock management unit (CMU) that provides innovative clocking capabilities. The proposed CMU is achieved by utilizing edge-triggered D-type flip-flops (D-FFs) in the design of frequency synthesizer and phase splitter. Edge-triggered D-FF structures proposed in this paper have the successful QCA implementation and simulation with the least complexity and power dissipation as compared to earlier structures. The frequency synthesizer is used to generate new clock frequencies from the reference clock frequency based on a combination of power-of-two frequency dividers. The phase splitter is integrated with the frequency synthesizer to generate four clock signals that are 90o out of phase with each other. This paper demonstrates that the proposed QCA CMU structure has a superior performance. Furthermore, the proposed CMU is straightforwardly scalable due to the use of modular component architecture.

Electronic Escape Trails for Firefighters

NASA Technical Reports Server (NTRS)

Jorgensen, Charles; Schipper, John; Betts, Bradley

2008-01-01

A proposed wireless-communication and data-processing system would exploit recent advances in radio-frequency identification devices (RFIDs) and software to establish information lifelines between firefighters in a burning building and a fire chief at a control station near but outside the building. The system would enable identification of trails that firefighters and others could follow to escape from the building, including identification of new trails should previously established trails become blocked. The system would include a transceiver unit and a computer at the control station, portable transceiver units carried by the firefighters in the building, and RFID tags that the firefighters would place at multiple locations as they move into and through the building (see figure). Each RFID tag, having a size of the order of a few centimeters, would include at least standard RFID circuitry and possibly sensors for measuring such other relevant environmental parameters as temperature, levels of light and sound, concentration of oxygen, concentrations of hazardous chemicals in smoke, and/or levels of nuclear radiation. The RFID tags would be activated and interrogated by the firefighters and control-station transceivers. Preferably, RFID tags would be configured to communicate with each other and with the firefighters units and the control station in an ordered sequence, with built-in redundancy. In a typical scenario, as firefighters moved through a building, they would scatter many RFID tags into smoke-obscured areas by use of a compressed-air gun. Alternatively or in addition, they would mark escape trails by dropping RFID tags at such points of interest as mantraps, hot spots, and trail waypoints. The RFID tags could be of different types, operating at different frequencies to identify their functions, and possibly responding by emitting audible beeps when activated by signals transmitted by transceiver units carried by nearby firefighters.

THE INTEGRATION OF THE 241-Z BUILDING DECONTAMINATION & DECOMMISSIONING (D&D) UNDER COMPREHENSIVE ENVIRONMENTAL RESPONSE COMPENSATION & LIABILITY ACT (CERCLA) WITH RESOURCE CONSERVATION & RECOVERY ACT (RCRA) CLOSURE AT THE PLUTONIUM FINISHING PLANT (PFP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

HOPKINS, A.M.

2007-02-20

The 241-Z treatment and storage tanks, a hazardous waste Treatment, Storage and Disposal (TSD) unit permitted pursuant to the ''Resource Conservation and Recovery Act of 1976'' (RCRA) and Washington State ''Hazardous Waste Management Act, RCW 70.105'', have been deactivated and are being actively decommissioned. The 241-Z TSD unit managed non-listed radioactive contaminated waste water, containing trace RCRA characteristic constituents. The 241-Z TSD unit consists of below grade tanks (D-4, D-5, D-7, D-8, and an overflow tank) located in a concrete containment vault, sample glovebox GB-2-241-ZA, and associated ancillary piping and equipment. The tank system is located beneath the 241-Z building.more » The 241-Z building is not a portion of the TSD unit. The sample glovebox is housed in the above-grade building. Waste managed at the TSD unit was received via underground mining from Plutonium Finishing Plant (PFP) sources. Tank D-6, located in the D-6 vault cell, is a past-practice tank that was taken out of service in 1972 and has never operated as a portion of the RCRA TSD unit. CERCLA actions address Tank D-6, its containment vault cell, and soil beneath the cell that was potentially contaminated during past-practice operations and any other potential past-practice contamination identified during 241-Z closure, while outside the scope of the ''Hanford Facility Dangerous Waste Closure Plant, 241-Z Treatment and Storage Tanks''.« less

164. Photocopied July 1978. VIEW OF STEAMTURBINE BUILDING AT STAMP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

164. Photocopied July 1978. VIEW OF STEAM-TURBINE BUILDING AT STAMP MILL. BUILDING CONSTRUCTED IN 1921 TO USE EXHAUST STEAM TO GENERATE ELECTRICITY. C. 1925. - Quincy Mining Company, Hancock, Houghton County, MI

19. Launch Area, general view of Missile Assembly Building and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. Launch Area, general view of Missile Assembly Building and Generator Building VIEW SOUTHWEST - NIKE Missile Battery PR-79, Launch Area, East Windsor Road south of State Route 101, Foster, Providence County, RI

Response measurements for two building structures excited by noise from a large horizontal axis wind turbine generator

NASA Technical Reports Server (NTRS)

Hubbard, H. H.; Shepherd, K. P.

1984-01-01

Window and wall acceleration measurements and interior noise measurements ere made for two different building structures during excitation by noise from the WTS-4 horizontal axis wind turbine generator operating in a normal power generation mode. With turbine noise input pulses resulted in acceleration pulses for the wall and window elements of the two tests buildings. Response spectra suggest that natural vibration modes of the structures are excited. Responses of a house trailer were substantially greater than those for a building of sturdier construction. Peak acceleration values correlate well with similar data for houses excited by flyover noise from commercial and military airplanes and helicopters, and sonic booms from supersonic aircraft. Interior noise spectra have peaks at frequencies corresponding to structural vibration modes and room standing waves; and the levels for particular frequencies and locations can be higher than the outside levels.

The application, benefits and challenges of retrofitting the existing buildings

NASA Astrophysics Data System (ADS)

Khairi, Muhammad; Jaapar, Aini; Yahya, Zaharah

2017-11-01

Sustainable development has been the main topic of debate for years in some countries such as United Kingdom, United State of America and Malaysia. Depletion of natural resources, global warming, economics uncertainty and health issues are some of the reasons behind sustainable development movements, it is not just a political debate in the parliament but more towards collective works among sectors in order to minimizing the negative impact of development to the environment and other living organism. Retrofit an existing building is one of the solutions to reduce the dependency on constructing new buildings. There are huge numbers of existing building stocks that suitable to be retrofitted such as historical buildings, offices, residential, warehouse, factories, vacant buildings and other historical buildings. Therefore, the aim of this research is to provide information on the application, benefits and challenges of retrofitting an existing building. Two buildings were chosen as case studies following by site visits and observation to the buildings. The data were then compared in a table form. Primary and secondary sources were also used for this research. The application of retrofit should be promoted across the construction and conservation industries since it has significant tangible and intangible benefits. It is one of the most environmentally friendly and efficient solutions to optimize the energy performance and could also helps to extend the life of the existing building or historical buildings while ensuring optimum thermal comfort for the occupants which leads to higher productivity.

24 CFR 1003.602 - Relocation and real property acquisition.

Code of Federal Regulations, 2010 CFR

2010-04-01

... may occupy a suitable, decent, safe, and sanitary dwelling in the building/complex following... dwelling unit who moves from the building/complex permanently after the submission to HUD of an application... project. (iii) A tenant-occupant of a dwelling who moves from the building/complex permanently, after the...

2. VIEW OF NORTHEAST (GABLE END) AND SOUTHEAST SIDES FROM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. VIEW OF NORTHEAST (GABLE END) AND SOUTHEAST SIDES FROM THE NORTHEAST. (BUILDING 111 VISIBLE ON LEFT; BUILDING 114 AT RIGHT.) INTERIOR OF BUILDING 113 TO THE SOUTHEAST.) - Fort McPherson, World War II Station Hospital, G. U. Treatment Unit Lavatory, Thorne & Hood Avenues, Atlanta, Fulton County, GA

PRACTICAL EXPERIENCES WITH TECHNOLOGIES FOR DECONTAMINATION OF B. ANTHRACIS IN LARGE BUILDINGS.

EPA Science Inventory

In the Fall of 2001 a number of buildings were contaminated with B. anthracis (B.A.) from letters processed through United States Postal Service and other mail handling facilities. All of the buildings have now been decontaminated using a variety of technologies. In a number of...

24 CFR 200.937 - Supplementary specific procedural requirements under HUD building product standards and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... requirements under HUD building product standards and certification program for plastic bathtub units, plastic... procedural requirements under HUD building product standards and certification program for plastic bathtub... product certification program. In the case of plastic bathroom fixtures, testing and inspection shall be...

77 FR 26647 - National Building Safety Month, 2012

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-04

... Building Safety Month, 2012 By the President of the United States of America A Proclamation In... to an America built to last, and during National Building Safety Month, we recommit to strengthening... critical role in making America safe, strong, and sustainable. This month, we celebrate their work, and we...

Theory Building and Modeling in a Sinking and Floating Unit: A Case Study of Third and Fourth Grade Students' Developing Epistemologies of Science

ERIC Educational Resources Information Center

Kawasaki, Keiko; Rupert Herrenkohl, Leslie; Yeary, Sherry

2004-01-01

The purpose of this paper is to carefully examine the evolution of students' theory building and modeling, critical components of scientific epistemologies, over a unit of study on sinking and floating in one third/fourth grade classroom. The study described in this paper follows in the tradition of Design Experiments ( Brown 1992 , Collins 1990 )…

The United States Army Medical Department Journal. April-June 2010

DTIC Science & Technology

2010-06-01

AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) US Army Medical Department...change catalyst, conflict management, building bonds, collaboration and cooperation, and teamwork ). Given the goals of the workshop, the mentoring...do just that—provide medical professionals with a multitude of resiliency building skills to enhance their resiliency framework over time across

48 CFR 3036.104-90 - Authority for one-step turn-key design-build contracting for the United States Coast Guard (USCG).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Authority for one-step... General 3036.104-90 Authority for one-step turn-key design-build contracting for the United States Coast Guard (USCG). The Head of the Contracting Activity (HCA) of the U.S. Coast Guard may use one-step turn...

High performance gas adsorption and separation of natural gas in two microporous metal-organic frameworks with ternary building units.

PubMed

Wang, Dongmei; Zhao, Tingting; Cao, Yu; Yao, Shuo; Li, Guanghua; Huo, Qisheng; Liu, Yunling

2014-08-14

Two novel MMOFs, JLU-Liu5 and JLU-Liu6, are based on ternary building units and exhibit high adsorption selectivity for CO2, C2H6 and C3H8 over CH4, which is attributed to steric effects and host-guest interactions. These MMOFs are promising materials for gas adsorption and natural gas purification.

New Academic Partnerships in Global Health: Innovations at Mount Sinai School of Medicine

PubMed Central

Landrigan, Philip J.; Ripp, Jonathan; Murphy, Ramon J. C.; Claudio, Luz; Jao, Jennifer; Hexom, Braden; Bloom, Harrison G.; Shirazian, Taraneh; Elahi, Ebby; Koplan, Jeffrey P.

2011-01-01

Global health has become an increasingly important focus of education, research, and clinical service in North American universities and academic health centers. Today there are at least 49 academically based global health programs in the United States and Canada, as compared with only one in 1999. A new academic society, the Consortium of Universities for Global Health, was established in 2008 and has grown significantly. This sharp expansion reflects convergence of 3 factors: (1) rapidly growing student and faculty interest in global health; (2) growing realization–powerfully catalyzed by the acquired immune deficiency syndrome epidemic, the emergence of other new infections, climate change, and globalization–that health problems are interconnected, cross national borders, and are global in nature; and (3) rapid expansion in resources for global health. This article examines the evolution of the concept of global health and describes the driving forces that have accelerated interest in the field. It traces the development of global health programs in academic health centers in the United States. It presents a blueprint for a new school-wide global health program at Mount Sinai School of Medicine. The mission of that program, Mount Sinai Global Health, is to enhance global health as an academic field of study within the Mount Sinai community and to improve the health of people around the world. Mount Sinai Global Health is uniting and building synergies among strong, existing global health programs within Mount Sinai; it is training the next generation of physicians and health scientists to be leaders in global health; it is making novel discoveries that translate into blueprints for improving health worldwide; and it builds on Mount Sinai’s long and proud tradition of providing medical and surgical care in places where need is great and resources few. PMID:21598272

Primary Energy of the District city and Suburb

NASA Astrophysics Data System (ADS)

Pitonak, Anton; Lopusniak, Martin; Bagona, Miloslav

2017-10-01

In member states of the European Union, portion of buildings in the total consumption of energy represents 40 %, and their share in CO2 emissions represents 35 %. Taking into account the dependence of the European Union on import of energy, this represents a large quantity of energy and CO2 in spite of the fact that effective solutions for the reduction of energy demand of buildings exist. The European Union adopted three main commitments for fulfilment of criteria by year 2020 in the 20-20-20 Directive. Based on this Directive Slovakia declares support for renovating the building stock. The goal of the paper was to prove that renovation of the building stock is environmentally and energy preferably as construction of new buildings. In the paper, the settlement unit with the suburban one were compared. Both territories are dealt with in Kosice city, in Slovakia. The settlement units include apartment dwelling houses, amenities, parking areas and green. Suburban part contains family houses. The decisive factor for the final assessment of the buildings was global indicator. Global indicator of the energy performance is primary energy. The new building must meet minimum requirements for energy performance and it must be classified to energy class A1 since 2016, and to energy class A0 since 2020. The paper analyses the effects of the use of different resources of heat considering the global indicator. Primary energy was calculated and based on comparable unit. The primary energy was accounted for on the built-up area, area corresponding to district city and suburb, number of inhabitants. The study shows that the lowest values of global indicator are achieved by using wood. The highest values of global indicator are achieved by using electricity or district heating as an energy source. The difference between the highest and lowest value is 87 %. Primary energy based on inhabitant is 98 % lower in settlement unit compared to the suburban one.

Building Energy Asset Score for Building Owners

DOE Office of Scientific and Technical Information (OSTI.GOV)

Building Technologies Office

2015-01-01

The Building Energy Asset Score is a national standardized tool for evaluating the physical and structural energy efficiency of commercial and multifamily residential buildings. The Asset Score generates a simple energy efficiency rating that enables comparison among buildings, and identifies opportunities for users to invest in energy efficiency upgrades. It is web-based and free to use. This fact sheet discusses the value of the score for building owners.

Global optimization framework for solar building design

NASA Astrophysics Data System (ADS)

Silva, N.; Alves, N.; Pascoal-Faria, P.

2017-07-01

The generative modeling paradigm is a shift from static models to flexible models. It describes a modeling process using functions, methods and operators. The result is an algorithmic description of the construction process. Each evaluation of such an algorithm creates a model instance, which depends on its input parameters (width, height, volume, roof angle, orientation, location). These values are normally chosen according to aesthetic aspects and style. In this study, the model's parameters are automatically generated according to an objective function. A generative model can be optimized according to its parameters, in this way, the best solution for a constrained problem is determined. Besides the establishment of an overall framework design, this work consists on the identification of different building shapes and their main parameters, the creation of an algorithmic description for these main shapes and the formulation of the objective function, respecting a building's energy consumption (solar energy, heating and insulation). Additionally, the conception of an optimization pipeline, combining an energy calculation tool with a geometric scripting engine is presented. The methods developed leads to an automated and optimized 3D shape generation for the projected building (based on the desired conditions and according to specific constrains). The approach proposed will help in the construction of real buildings that account for less energy consumption and for a more sustainable world.

Automated Continuous Commissioning of Commercial Buildings

DTIC Science & Technology

2011-10-01

energy annually at the building level on two demonstration sites. Some faults would also cause issues related to thermal comfort . 2 $ Economizer...Unit (AHU) discharge air temperatures and room temperatures to deviate from their respective setpoints. This causes building thermal comfort issues...annual expenditure savings over the next three to five years. At the same time, the thermal comfort in DoD buildings would be improved to result in

Systems Approach to Building. A Brief Report on the Canadian Scene in November 1969 with Particular Reference to School and College Construction.

ERIC Educational Resources Information Center

Halsall, R.

The history, advantages, and disadvantages of component building systems are discussed. Application of the scientific method to the building industry forecasts the use of prefabrication and on-site erection of factory-made subsystems of buildings. Educational facilities in the United States, Canada, and England have made use of many different…

New "Risk-Targeted" Seismic Maps Introduced into Building Codes

USGS Publications Warehouse

Luco, Nicholas; Garrett, B.; Hayes, J.

2012-01-01

Throughout most municipalities of the United States, structural engineers design new buildings using the U.S.-focused International Building Code (IBC). Updated editions of the IBC are published every 3 years. The latest edition (2012) contains new "risk-targeted maximum considered earthquake" (MCER) ground motion maps, which are enabling engineers to incorporate a more consistent and better defined level of seismic safety into their building designs.

Promising Practices: Building the Next Generation of School Leaders

ERIC Educational Resources Information Center

Bryant, Jennifer Edic; Escalante, Karen; Selva, Ashley

2017-01-01

This study applies transformational leadership theory practices to examine the purposeful ways in which principals work to build the next generation of teacher leaders in response to the shortage of K-12 principals. Given the impact principals have on student development and the shortage of those applying for the principalship, the purpose of this…

VIEW OF BUILDING 440 LOOKING WEST, NORTHWEST. BUILDING 440, THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF BUILDING 440 LOOKING WEST, NORTHWEST. BUILDING 440, THE TRANSPORT MODIFICATION CENTER, CONSISTS OF FOUR HIGH-BAY CORRUGATED METAL STRUCTURES. BUILDING 440 WAS USED FOR PACKAGING AND STAGING SPECIAL NUCLEAR MATERIALS AND DEPLETED URANIUM FOR SHIPMENT AND TO MODIFY VEHICLES TO MEET SPECIFIC UNITED STATES DEPARTMENT OF ENERGY REQUIREMENTS. (2/8/84) - Rocky Flats Plant, Transport Modification Center, North of Cactus Avenue, approximately 400 feet east of Third Street, Golden, Jefferson County, CO

NREL’s Advanced Analytics Research for Energy-Efficient Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kutscher, Chuck; Livingood, Bill; Wilson, Eric

At NREL, we believe in building better buildings. More importantly, high-performance buildings that can do more and be smarter than ever before. Forty percent of the total energy consumption in the United States comes from buildings. Working together, we can dramatically shrink that number. But first, it starts with the research: our observations, experiments, modeling, analysis, and more. NREL’s advanced analytics research has already proven to reduce energy use, save money, and stabilize the grid.

7 CFR 2900.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... domestic market, and for export, for building of reserves, and crops for soil building or conservation... maintenance of food quality after processing. (b) Establishment means an economic unit, generally at a single...

36. SITE BUILDING 004 ELECTRIC POWER STATION CLOSE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

36. SITE BUILDING 004 - ELECTRIC POWER STATION - CLOSE UP VIEW OF 1200 HORSEPOWER STANDBY POWER DIESEL ENGINE/GENERATOR SETS. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

37. SITE BUILDING 004 ELECTRIC POWER STATION ELEVATED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. SITE BUILDING 004 - ELECTRIC POWER STATION - ELEVATED VIEW OF FIVE (5) 1200 HORSEPOWER STANDBY - POWER DIESEL ENGINE/GENERATOR SETS. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

Minimum separation distances for natural gas pipeline and boilers in the 300 area, Hanford Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daling, P.M.; Graham, T.M.

1997-08-01

The U.S. Department of Energy (DOE) is proposing actions to reduce energy expenditures and improve energy system reliability at the 300 Area of the Hanford Site. These actions include replacing the centralized heating system with heating units for individual buildings or groups of buildings, constructing a new natural gas distribution system to provide a fuel source for many of these units, and constructing a central control building to operate and maintain the system. The individual heating units will include steam boilers that are to be housed in individual annex buildings located at some distance away from nearby 300 Area nuclearmore » facilities. This analysis develops the basis for siting the package boilers and natural gas distribution systems to be used to supply steam to 300 Area nuclear facilities. The effects of four potential fire and explosion scenarios involving the boiler and natural gas pipeline were quantified to determine minimum separation distances that would reduce the risks to nearby nuclear facilities. The resulting minimum separation distances are shown in Table ES.1.« less

The biological microprocessor, or how to build a computer with biological parts

PubMed Central

Moe-Behrens, Gerd HG

2013-01-01

Systemics, a revolutionary paradigm shift in scientific thinking, with applications in systems biology, and synthetic biology, have led to the idea of using silicon computers and their engineering principles as a blueprint for the engineering of a similar machine made from biological parts. Here we describe these building blocks and how they can be assembled to a general purpose computer system, a biological microprocessor. Such a system consists of biological parts building an input / output device, an arithmetic logic unit, a control unit, memory, and wires (busses) to interconnect these components. A biocomputer can be used to monitor and control a biological system. PMID:24688733

The Control Unit of KM3NeT data acquisition

NASA Astrophysics Data System (ADS)

Bozza, Cristiano

2016-04-01

The KM3NeT Collaboration is building a new generation of neutrino telescopes in the Mediterranean Sea. With the telescopes, scientists will search for cosmic neutrinos to study highly energetic objects in the Universe, while one neutrino detector will be dedicated to measure the properties of the high-energy neutrino particles themselves. Control of the KM3NeT data acquisition processes is handled by the KM3NeT Control Unit, which has been designed to maximise the detector live time. The Control Unit features software programs with different roles, following the philosophy of having no single point of failure. While all programs are interconnected, each one can also work alone for most of the time in case other services are unavailable. All services run on the Common Language Runtime, which ensures portability, flexibility and automatic memory management. Each service has an embedded Web server, providing a user interface as well as programmatic access to data and functions. Data to and from detector components for monitoring and management purposes are transmitted using a custom designed protocol. The Control Unit is interfaced to one or more Message Dispatchers to control the data acquisition chain. A Data Base Interface provides fast and fault-tolerant connection to a remote Data Base.

Direct local building inundation depth determination in 3-D point clouds generated from user-generated flood images

NASA Astrophysics Data System (ADS)

Griesbaum, Luisa; Marx, Sabrina; Höfle, Bernhard

2017-07-01

In recent years, the number of people affected by flooding caused by extreme weather events has increased considerably. In order to provide support in disaster recovery or to develop mitigation plans, accurate flood information is necessary. Particularly pluvial urban floods, characterized by high temporal and spatial variations, are not well documented. This study proposes a new, low-cost approach to determining local flood elevation and inundation depth of buildings based on user-generated flood images. It first applies close-range digital photogrammetry to generate a geo-referenced 3-D point cloud. Second, based on estimated camera orientation parameters, the flood level captured in a single flood image is mapped to the previously derived point cloud. The local flood elevation and the building inundation depth can then be derived automatically from the point cloud. The proposed method is carried out once for each of 66 different flood images showing the same building façade. An overall accuracy of 0.05 m with an uncertainty of ±0.13 m for the derived flood elevation within the area of interest as well as an accuracy of 0.13 m ± 0.10 m for the determined building inundation depth is achieved. Our results demonstrate that the proposed method can provide reliable flood information on a local scale using user-generated flood images as input. The approach can thus allow inundation depth maps to be derived even in complex urban environments with relatively high accuracies.

Combined installation of electric and heat supply for climatic conditions of Iraq

NASA Astrophysics Data System (ADS)

Kaisi, Osama Al; Sidenkov, D. V.

2017-11-01

Electricity, heating and cooling are the three main components that make up the energy consumption base in residential, commercial and public buildings around the world. Demand for energy and fuel costs are constantly growing. Combined cooling, heating and power generation or trigeneration can be a promising solution to such a problem, providing an efficient, reliable, flexible, competitive and less harmful alternative to existing heat and cold supply systems. In this paper, scheme of the tri-generation plant on non-aqueous working substances is considered as an installation of a locally centralized electro-heat and cold supply of a typical residential house in a hot climate. The scheme of the combined installation of electro-heat (cold) supply consisted of the vapor power plant and heat pump system on low-boiling working substance for local consumers under the climatic conditions of Iraq is presented. The possibility of using different working substances in the thermodynamic cycles of these units, which will provide better efficiency of such tri-generation systems is shown. The calculations of steam turbine cycles and heat pump part on the selected working substances are conducted. It is proposed to use heat exchangers of plate type as the main exchangers in the combined processing. The developed method of thermal-hydraulic calculation of heat exchangers implemented in MathCad, which allows to evaluate the efficiency of plants of this type using the ε - NTU method. For the selected working substances of the steam part the optimal temperature of heat supply to the steam generator is determined. The results of thermodynamic and technical-economic analysis of the application of various working substances in the “organic” Rankine cycle of the steam turbine unit and the heat pump system of the heat and cold supply system are presented.

The implementation of unit price of work standard SNI 7394: 2008 for the construction of reinforced concrete beam

NASA Astrophysics Data System (ADS)

Tripoli; Mubarak; Nurisra; Mahmuddin

2018-05-01

This paper discusses the implementation of Indonesian National Standard (SNI) 7394: 2008 on procedures for calculating the unit price of concrete work for the construction of building and housing. The standard provides some reinforced concrete constructions unit price (UP) analysis by specified the total number of reinforcing uses. Related to reinforced concrete beam work (Analysis No. 6.31), the reinforcement requirement is stated at 200 kg/m3 of concrete. Once the implementation considers various earthquake zoning, the question will arise about the extent to which the standard is feasible to apply. Therefore, this research aimed to analyze the possibility of UP standard implementation by certain earthquake zonation. This research is focused on the construction of reinforced concrete beam for buildings with function as educational, residential and office buildings. The data used are sourced from 21 buildings in two zones in Aceh Province, covering Zone 10 and Zone 15 based on earthquake map of SNI 1726: 2012. The analysis results indicate that the UP standard for reinforced concrete beam cannot be applied to all zoning. The UP standard is only possible on buildings constructed in Zone 10 or zonation with seismic spectral response 0.6g to 0.7g or lower.

Superfund record of decision amendment (EPA Region 10): USAF Eielson Air Force Base, Operable Units 3, 4, and 5, Fairbanks North Star Borough, AK, September 29, 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This decision document presents the amended remedial action for Operable Units 3, 4, and 5 (OUs 3, 4, and 5) at Eielson Air Force Base (AFB). This decision is based on the Administrative Record for OU 3, 4, and 5, updated in July 1998, to include new information generated since the original Record of Decision was signed on 30 September 1995 (PB95-964618). This amendment applies to OU3 site DP44 (Battery Shop Leach Field Building), OU4 sites SS35 (Asphalt Mixing Area) and ST58 (Old Quartermaster Service Station), and OU5 sites LF03/FT09 (Current Inactive Base Landfill/Fire Training Area). Through new information, contaminantmore » levels than interpreted prior to signing the original ROD document. Proper enforcement of Institutional Controls (IC`s) at all sites will be effective in controlling and restricting access to contaminated media at the sites remediation goals are achieved.« less

General synthesis and physicochemical characterisation of a series of peptide-mimic lysine-based amino-functionalised lipids.

PubMed

Wölk, Christian; Drescher, Simon; Meister, Annette; Blume, Alfred; Langner, Andreas; Dobner, Bodo

2013-09-16

A series of novel malonic acid diamides (second generation) with two long hydrophobic alkyl chains and an alkaline polar head group was synthesised and characterised as a new class of amino-functionalised lipids. These peptide-mimic lipids are suitable for polynucleotide transfer. The lipids bear a novel backbone consisting of a lysine unit and a malonic acid unit. Six different head-group structures, which vary in size and number of amino groups that can be protonated, were attached to the backbone structure. Furthermore, different alkyl chains were used to build the lipophilic part (namely tetradecyl, hexadecyl, and oleyl). Phase transitions of the new compounds in aqueous dispersions at pH 10 were analysed and discussed in terms of head group and alkyl chain variations. The shape and size of the formed aggregates of selected lipid dispersions were investigated by dynamic light scattering and transmission electron microscopy. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Bringing Solid-State Magnetocaloric Cooling to the Market: A Commercialization Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abu-Heiba, Ahmad; Sikes, Karen; Blackburn, Julia

Air conditioning has become a staple in American life, bringing improved health, productivity, and comfort to 93% of single-family homes as of 2015, compared to only 76% in 1990. This rise in demand has contributed to the 2.51 quads (12.5%) of total annual energy consumption in residential buildings attributable to space cooling (U.S. Energy Information Administration 2017). Accompanying this upward trend in space cooling has been increased refrigerant use, which has historically contributed to ozone depletion, global warming, or both. The Oak Ridge National Laboratory – along with German-based partner Vacuumschmelze GmbH & Co. KG – is working to reducemore » energy consumption and refrigerant use through the development of a next-generation, solid-state magnetocaloric cooling system. The purpose of this study is to investigate market potential of these systems in the United States, including information on the industry landscape, market share and unit shipment projections, optimal price points, and barriers to market entry.« less

Reducing Health Inequities in the United States: Insights and Recommendations from the National Heart, Lung, and Blood Institute’s Health Inequities Think Tank Meeting

PubMed Central

Sampson, Uchechukwu K.A.; Kaplan, Robert M.; Cooper, Richard S.; Diez Roux, Ana V.; Marks, James S.; Engelgau, Michael M.; Peprah, Emmanuel; Mishoe, Helena; Boulware, L. Ebony; Felix, Kaytura L.; Califf, Robert M.; Flack, John M.; Cooper, Lisa A.; Gracia, J. Nadine; Henderson, Jeffrey A.; Davidson, Karina W.; Krishnan, Jerry A.; Lewis, Tené T.; Sanchez, Eduardo; Luban, Naomi L.; Vaccarino, Viola; Wong, Winston F.; Wright, Jackson T.; Meyers, David; Ogedegbe, Olugbenga G.; Presley-Cantrell, Letitia; Chambers, David A.; Belis, Deshirée; Bennett, Glen C.; Boyington, Josephine E; Creazzo, Tony L.; de Jesus, Janet M.; Krishnamurti, Chitra; Lowden, Mia R.; Punturieri, Antonello; Shero, Susan T.; Young, Neal S.; Zou, Shimian; Mensah, George A.

2016-01-01

The National, Heart, Lung, and Blood Institute convened a Think Tank meeting to obtain insight and recommendations regarding the objectives and design of the next generation of research aimed at reducing health inequities in the United States. The panel recommended several specific actions, including: 1) Embrace broad and inclusive research themes; 2) Develop research platforms that optimize the ability to conduct informative and innovative research, and promote systems science approaches; 3) Develop networks of collaborators and stakeholders, and launch transformative studies that can serve as benchmarks; 4) Optimize the use of new data sources, platforms, and natural experiments; and 5) develop unique transdisciplinary training programs to build research capacity. Confronting health inequities will require engaging multiple disciplines and sectors (including communities), using systems science, and intervening through combinations of individual, family, provider, health system, and community-targeted approaches. Details of the panel’s remarks and recommendations are provided in this report. PMID:27470459

Minimizing forced outage risk in generator bidding

NASA Astrophysics Data System (ADS)

Das, Dibyendu

Competition in power markets has exposed the participating companies to physical and financial uncertainties. Generator companies bid to supply power in a day-ahead market. Once their bids are accepted by the ISO they are bound to supply power. A random outage after acceptance of bids forces a generator to buy power from the expensive real-time hourly spot market and sell to the ISO at the set day-ahead market clearing price, incurring losses. A risk management technique is developed to assess this financial risk associated with forced outages of generators and then minimize it. This work presents a risk assessment module which measures the financial risk of generators bidding in an open market for different bidding scenarios. The day-ahead power market auction is modeled using a Unit Commitment algorithm and a combination of Normal and Cauchy distributions generate the real time hourly spot market. Risk profiles are derived and VaRs are calculated at 98 percent confidence level as a measure of financial risk. Risk Profiles and VaRs help the generators to analyze the forced outage risk and different factors affecting it. The VaRs and the estimated total earning for different bidding scenarios are used to develop a risk minimization module. This module will develop a bidding strategy of the generator company such that its estimated total earning is maximized keeping the VaR below a tolerable limit. This general framework of a risk management technique for the generating companies bidding in competitive day-ahead market can also help them in decisions related to building new generators.

12. GENERAL VIEW TO THE WEST FROM NEAR BUILDING NO. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. GENERAL VIEW TO THE WEST FROM NEAR BUILDING NO. 14 (CONTROL HOUSE FOR DRY DOCK), NOW LOCATED AT THE EAST END OF THE PROJECT AREA. IN THE LEFT FAR DISTANCE ARE TWO WATER TOWERS OF THE FORMER ALAMEDA NAVAL AIR STATION. DIRECTLY BENEATH THEM IS THE FRAME OF BUILDING NO. 6. BUILDING NO. 1 IS IN THE CENTER DISTANCE, MOSTLY OBSCURED BY A MODERN METAL BUILDING. BUILDING NO. 18 AND THE WET BASIN ARE AT RIGHT CENTER, IN DISTANCE. - United Engineering Company Shipyard, 2900 Main Street, Alameda, Alameda County, CA

Establishing a National 3d Geo-Data Model for Building Data Compliant to Citygml: Case of Turkey

NASA Astrophysics Data System (ADS)

Ates Aydar, S.; Stoter, J.; Ledoux, H.; Demir Ozbek, E.; Yomralioglu, T.

2016-06-01

This paper presents the generation of the 3D national building geo-data model of Turkey, which is compatible with the international OGC CityGML Encoding Standard. We prepare an ADE named CityGML-TRKBIS.BI that is produced by extending existing thematic modules of CityGML according to TRKBIS needs. All thematic data groups in TRKBIS geo-data model have been remodelled in order to generate the national large scale 3D geo-data model for Turkey. Specific attention has been paid to data groups that have different class structure according to related CityGML data themes such as building data model. Current 2D geo-information model for building data theme of Turkey (TRKBIS.BI) was established based on INSPIRE specifications for building (Core 2D and Extended 2D profiles), ISO/TC 211 standards and OGC web services. New version of TRKBIS.BI which is established according to semantic and geometric rules of CityGML will represent 2D-2.5D and 3D objects. After a short overview on generic approach, this paper describes extending CityGML building data theme according to TRKBIS.BI through several steps. First, building models of both standards were compared according to their data structure, classes and attributes. Second, CityGML building model was extended with respect to TRKBIS needs and CityGML-TRKBIS Building ADE was established in UML. This study provides new insights into 3D applications in Turkey. The generated 3D geo-data model for building thematic class will be used as a common exchange format that meets 2D, 2.5D and 3D implementation needs at national level.

Country Report on Building Energy Codes in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shui, Bin; Evans, Meredydd

2009-04-06

This report is part of a series of reports on building energy efficiency codes in countries associated with the Asian Pacific Partnership (APP) - Australia, South Korea, Japan, China, India, and the United States of America . This reports gives an overview of the development of building energy codes in Canada, including national energy policies related to building energy codes, history of building energy codes, recent national projects and activities to promote building energy codes. The report also provides a review of current building energy codes (such as building envelope, HVAC, lighting, and water heating) for commercial and residential buildingsmore » in Canada.« less

7. PHOTOCOPY, PLANS, ELEVATIONS, AND SECTION DRAWING FOR MISSILE TEST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. PHOTOCOPY, PLANS, ELEVATIONS, AND SECTION DRAWING FOR MISSILE TEST AND ASSEMBLY BUILDING. - NIKE Missile Base SL-40, Missile Test & Assembly Building, South end of launch area, northeast of Generator Building No. 3, Hecker, Monroe County, IL

35. SITE BUILDING 004 ELECTRIC POWER STATION CONTROL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

35. SITE BUILDING 004 - ELECTRIC POWER STATION - CONTROL ROOM OF ELECTRIC POWER STATION WITH DIESEL ENGINE POWERED ELECTRIC GENERATION EQUIPMENT IN BACKGROUND. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

38. SITE BUILDING 004 ELECTRIC POWER STATION AT INTERIOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

38. SITE BUILDING 004 - ELECTRIC POWER STATION AT INTERIOR - OBLIQUE VIEW AT FLOOR LEVEL SHOWING DIESEL ENGINE/GENERATOR SET NUMBER 5. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

A simulation-based efficiency comparison of AC and DC power distribution networks in commercial buildings

DOE PAGES

Gerber, Daniel L.; Vossos, Vagelis; Feng, Wei; ...

2017-06-12

Direct current (DC) power distribution has recently gained traction in buildings research due to the proliferation of on-site electricity generation and battery storage, and an increasing prevalence of internal DC loads. The research discussed in this paper uses Modelica-based simulation to compare the efficiency of DC building power distribution with an equivalent alternating current (AC) distribution. The buildings are all modeled with solar generation, battery storage, and loads that are representative of the most efficient building technology. A variety of paramet ric simulations determine how and when DC distribution proves advantageous. These simulations also validate previous studies that use simplermore » approaches and arithmetic efficiency models. This work shows that using DC distribution can be considerably more efficient: a medium sized office building using DC distribution has an expected baseline of 12% savings, but may also save up to 18%. In these results, the baseline simulation parameters are for a zero net energy (ZNE) building that can island as a microgrid. DC is most advantageous in buildings with large solar capacity, large battery capacity, and high voltage distribution.« less

A simulation-based efficiency comparison of AC and DC power distribution networks in commercial buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gerber, Daniel L.; Vossos, Vagelis; Feng, Wei

Direct current (DC) power distribution has recently gained traction in buildings research due to the proliferation of on-site electricity generation and battery storage, and an increasing prevalence of internal DC loads. The research discussed in this paper uses Modelica-based simulation to compare the efficiency of DC building power distribution with an equivalent alternating current (AC) distribution. The buildings are all modeled with solar generation, battery storage, and loads that are representative of the most efficient building technology. A variety of paramet ric simulations determine how and when DC distribution proves advantageous. These simulations also validate previous studies that use simplermore » approaches and arithmetic efficiency models. This work shows that using DC distribution can be considerably more efficient: a medium sized office building using DC distribution has an expected baseline of 12% savings, but may also save up to 18%. In these results, the baseline simulation parameters are for a zero net energy (ZNE) building that can island as a microgrid. DC is most advantageous in buildings with large solar capacity, large battery capacity, and high voltage distribution.« less

High thermal conductivity materials for thermal management applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broido, David A.; Reinecke, Thomas L.; Lindsay, Lucas R.

High thermal conductivity materials and methods of their use for thermal management applications are provided. In some embodiments, a device comprises a heat generating unit (304) and a thermally conductive unit (306, 308, 310) in thermal communication with the heat generating unit (304) for conducting heat generated by the heat generating unit (304) away from the heat generating unit (304), the thermally conductive unit (306, 308, 310) comprising a thermally conductive compound, alloy or composite thereof. The thermally conductive compound may include Boron Arsenide, Boron Antimonide, Germanium Carbide and Beryllium Selenide.

69. INTERIOR VIEW OF THE ABSORPTION TOWER BUILDING, ABSORPTION TOWER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

69. INTERIOR VIEW OF THE ABSORPTION TOWER BUILDING, ABSORPTION TOWER UNDER CONSTRUCTION. (DATE UNKNOWN). - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

Theory Building and Modeling in a Sinking and Floating Unit: A Case Study of Third and Fourth Grade Students' Developing Epistemologies of Science. Research Report

ERIC Educational Resources Information Center

Kawasaki, Keiko; Herrenkohl, Leslie Rupert; Yeary, Sherry A.

2004-01-01

The purpose of this paper is to carefully examine the evolution of students' theory building and modeling, critical components of scientific epistemologies, over a unit of study on sinking and floating in one third/fourth grade classroom. The study described in this paper follows in the tradition of Design Experiments (Brown 1992, Collins 1990)…

Building Integrated Photovoltaic (BIPV) Roofs for Sustainability and Energy Efficiency

DTIC Science & Technology

2014-04-01

ACRONYMS A/C Air Conditioning a-Si Amorphous Silicon AC Alternating Current AFB Air Force Base AHU Air Handing Unit APS Arizona Public...Service ASTM American Society for Testing and Materials AZ Arizona BIPV Building Integrated Photovoltaic BTU British Thermal Units C Celsius CA...AFB) in Arizona (AZ). This site was chosen based on the ESTCP review board’s recommendation, the large size of the BIPV roof, and the age. Site I

International Energy Agency instrumented facilities survey for solar assisted low energy dwellings

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1982-02-01

Compiled are surveys outlining the instrumentation of 38 active and passive solar projects in 9 countries (Denmark, Italy, Japan, Netherlands, Sweden, Switzerland, United Kingdom, United States, and West Germany). After the surveys themselves are presented, the data are rearranged to compare answers from similar survey questions for each of the projects. These questions address building, solar system and instrumentation descriptions and meteorological, solar system and building system instrumentatation capabilities. (LEW)

Fuzzy Linguistic Knowledge Based Behavior Extraction for Building Energy Management Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dumidu Wijayasekara; Milos Manic

2013-08-01

Significant portion of world energy production is consumed by building Heating, Ventilation and Air Conditioning (HVAC) units. Thus along with occupant comfort, energy efficiency is also an important factor in HVAC control. Modern buildings use advanced Multiple Input Multiple Output (MIMO) control schemes to realize these goals. However, since the performance of HVAC units is dependent on many criteria including uncertainties in weather, number of occupants, and thermal state, the performance of current state of the art systems are sub-optimal. Furthermore, because of the large number of sensors in buildings, and the high frequency of data collection, large amount ofmore » information is available. Therefore, important behavior of buildings that compromise energy efficiency or occupant comfort is difficult to identify. This paper presents an easy to use and understandable framework for identifying such behavior. The presented framework uses human understandable knowledge-base to extract important behavior of buildings and present it to users via a graphical user interface. The presented framework was tested on a building in the Pacific Northwest and was shown to be able to identify important behavior that relates to energy efficiency and occupant comfort.« less

40. Photocopy of building model photograph, ca., 1974, photographer unknown. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

40. Photocopy of building model photograph, ca., 1974, photographer unknown. Original photograph property of United States Air Force, 21" Space Command. CAPE COD AIR STATION PAVE PAWS FACILITY MODEL - ELEVATION SHOWING FLOOR AND EQUIPMENT LAYOUT. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

39. Photocopy of building model photograph, ca. 1974, photographer unknown. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

39. Photocopy of building model photograph, ca. 1974, photographer unknown. Original photograph property of United States Air Force, 21" Space Command. CAPE COD AIR STATION PAVE PAWS FACILITY MODEL - SHOWING "A" AND "B" FACES. - Cape Cod Air Station, Technical Facility-Scanner Building & Power Plant, Massachusetts Military Reservation, Sandwich, Barnstable County, MA

Frequency of urban building fires as related to daily weather conditions

Treesearch

Arthur R. Pirsko; Wallace L. Fons

1956-01-01

Daily weather elements of precipitation, wind, mean temperature, relative humidity, and dew-point temperature for selected urban areas (approximately 850,000 population) in the United States are statistically analyzed to determine their correlation with daily number of building fires. The frequency of urban building fires is found to be significantly correlated with...

Environmental impact of producing hardwood lumber using life-cycle inventory

Treesearch

Richard D. Bergman; S.A. Bowe

2007-01-01

Using sustainable building materials is gaining a significant presence in the United States therefore proving sustainability claims are becoming increasingly more important. Showing wood products as green building materials is vital for the long-term productivity of the wood building industry. This study examined hardwood lumber manufacturing using Life-Cycle Inventory...

Measure of School Capacity for Improvement (MSCI). User Manual and Technical Report

ERIC Educational Resources Information Center

Hughes, Georgia K.; Copley, Lisa D.; Howley, Caitlin W.; Meehan, Merrill L.

2005-01-01

Building capacity within schools and districts for continuous improvement is a goal of educators at all levels across the United States of America. An important first step in capacity building is identifying schools' current strengths and weaknesses. Schools can then begin building upon existing strengths to implement improvement initiatives.…

76 FR 41196 - Notice of Funding Availability (NOFA): Section 515 Rural Rental Housing Program for New...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-13

... achieve in their certification: (a.) LEED for Homes program by the United States Green Building Council... Home Builders (NAHB) ICC 700- 2008 National Green Building Standard TM: http://www.nahb.org . (1... Level (10 points). iv. Participation in local green/energy efficient building standards; Applicants, who...

Credit PSR. This interior view of the building equipment room ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Credit PSR. This interior view of the building equipment room displays heat exchangers and fan units with insulated piping for hot and cold water at left. Environmental controls and fire fighting system controls appear at right - Jet Propulsion Laboratory Edwards Facility, Propellant Curing Building, Edwards Air Force Base, Boron, Kern County, CA

Balancing the Building Team: Gender Issues in the Building Professions. Report 284.

ERIC Educational Resources Information Center

Court, Gill; Moralee, Janet

The following activities were conducted to identify strategies for improving the representation of women in professional, managerial, and technical occupations in the United Kingdom's building industry: literature review; mail questionnaire to which 468 (63.8%) of the 733 women contacted responded; group discussions with 32 women employed in the…