Next-generation smart traffic signals : RHODES with Intellidrive, the self-taught traffic control system.

DOT National Transportation Integrated Search

2009-01-01

Can a self-calibrating signal control system lead to wider adoption of adaptive traffic control systems? The focus of Next Generation of Smart Traffic Signals, an Exploratory Advanced Research (EAR) Program project, is a system that-with lit...

Generation After Next Propulsor Research: Robust Design for Embedded Engine Systems

NASA Technical Reports Server (NTRS)

Arend, David J.; Tillman, Gregory; O'Brien, Walter F.

2012-01-01

The National Aeronautics and Space Administration, United Technologies Research Center and Virginia Polytechnic and State University have contracted to pursue multi-disciplinary research into boundary layer ingesting (BLI) propulsors for generation after next environmentally responsible subsonic fixed wing aircraft. This Robust Design for Embedded Engine Systems project first conducted a high-level vehicle system study based on a large commercial transport class hybrid wing body aircraft, which determined that a 3 to 5 percent reduction in fuel burn could be achieved over a 7,500 nanometer mission. Both pylon-mounted baseline and BLI propulsion systems were based on a low-pressure-ratio fan (1.35) in an ultra-high-bypass ratio engine (16), consistent with the next generation of advanced commercial turbofans. An optimized, coupled BLI inlet and fan system was subsequently designed to achieve performance targets identified in the system study. The resulting system possesses an inlet with total pressure losses less than 0.5%, and a fan stage with an efficiency debit of less than 1.5 percent relative to the pylon-mounted, clean-inflow baseline. The subject research project has identified tools and methodologies necessary for the design of next-generation, highly-airframe-integrated propulsion systems. These tools will be validated in future large-scale testing of the BLI inlet / fan system in NASA's 8 foot x 6 foot transonic wind tunnel. In addition, fan unsteady response to screen-generated total pressure distortion is being characterized experimentally in a JT15D engine test rig. These data will document engine sensitivities to distortion magnitude and spatial distribution, providing early insight into key physical processes that will control BLI propulsor design.

Reimagining Human Research Protections for 21st Century Science.

PubMed

Bloss, Cinnamon; Nebeker, Camille; Bietz, Matthew; Bae, Deborah; Bigby, Barbara; Devereaux, Mary; Fowler, James; Waldo, Ann; Weibel, Nadir; Patrick, Kevin; Klemmer, Scott; Melichar, Lori

2016-12-22

Evolving research practices and new forms of research enabled by technological advances require a redesigned research oversight system that respects and protects human research participants. Our objective was to generate creative ideas for redesigning our current human research oversight system. A total of 11 researchers and institutional review board (IRB) professionals participated in a January 2015 design thinking workshop to develop ideas for redesigning the IRB system. Ideas in 5 major domains were generated. The areas of focus were (1) improving the consent form and process, (2) empowering researchers to protect their participants, (3) creating a system to learn from mistakes, (4) improving IRB efficiency, and (5) facilitating review of research that leverages technological advances. We describe the impetus for and results of a design thinking workshop to reimagine a human research protections system that is responsive to 21st century science. ©Cinnamon Bloss, Camille Nebeker, Matthew Bietz, Deborah Bae, Barbara Bigby, Mary Devereaux, James Fowler, Ann Waldo, Nadir Weibel, Kevin Patrick, Scott Klemmer, Lori Melichar. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 22.12.2016.

An assessment of a traffic monitoring system for a major traffic generator to improve regional planning : technical report.

DOT National Transportation Integrated Search

2009-09-01

The opening of a major traffic generator in the San Antonio area provided an opportunity to develop and : implement an extensive traffic monitoring system to analyze local, area, and regional traffic impacts from the : generator. Researchers reviewed...

Automatic Chinese Factual Question Generation

ERIC Educational Resources Information Center

Liu, Ming; Rus, Vasile; Liu, Li

2017-01-01

Question generation is an emerging research area of artificial intelligence in education. Question authoring tools are important in educational technologies, e.g., intelligent tutoring systems, as well as in dialogue systems. Approaches to generate factual questions, i.e., questions that have concrete answers, mainly make use of the syntactical…

Next Generation MODTRAN for Improved Atmospheric Correction of Spectral Imagery

DTIC Science & Technology

2016-01-29

DoD operational and research sensor and data processing systems, particularly those involving the removal of atmospheric effects, commonly referred...atmospheric correction process. Given the ever increasing capabilities of spectral sensors to quickly generate enormous quantities of data, combined...many DoD operational and research sensor and data processing systems, particularly those involving the removal of atmospheric effects, commonly

78 FR 52941 - Cooperative Research and Development Agreement: Next Generation Arctic Navigational Safety...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-27

... Development Agreement: Next Generation Arctic Navigational Safety Information System AGENCY: Coast Guard, DHS... technology approach to the ``Next Generation Arctic Maritime Navigational Safety Information System,'' which... their voyage risks, as they transit the remote and hostile waters of the U.S. Arctic Exclusive Economic...

Basics of the dimensioning and operations of photovoltaic systems

NASA Astrophysics Data System (ADS)

Karl, H.

1984-06-01

Experiments and results in solar energy research are discussed. The characteristics of solar cells and photovoltaic generators are examined, and long-term experimental results on solar generators and hybrid collectors are reported. Photovoltaic systems are discussed, including battery systems, water pump systems, and hydrogen production by electrolysis.

Systematic Approach to Better Understanding Integration Costs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stark, Gregory B.

2015-09-01

This research presents a systematic approach to evaluating the costs of integrating new generation and operational procedures into an existing power system, and the methodology is independent of the type of change or nature of the generation. The work was commissioned by the U.S. Department of Energy and performed by the National Renewable Energy Laboratory to investigate three integration cost-related questions: (1) How does the addition of new generation affect a system's operational costs, (2) How do generation mix and operating parameters and procedures affect costs, and (3) How does the amount of variable generation (non-dispatchable wind and solar) impactmore » the accuracy of natural gas orders? A detailed operational analysis was performed for seven sets of experiments: variable generation, large conventional generation, generation mix, gas prices, fast-start generation, self-scheduling, and gas supply constraints. For each experiment, four components of integration costs were examined: cycling costs, non-cycling VO&M costs, fuel costs, and reserves provisioning costs. The investigation was conducted with PLEXOS production cost modeling software utilizing an updated version of the Institute of Electrical and Electronics Engineers 118-bus test system overlaid with projected operating loads from the Western Electricity Coordinating Council for the Sacramento Municipal Utility District, Puget Sound Energy, and Public Service Colorado in the year 2020. The test system was selected in consultation with an industry-based technical review committee to be a reasonable approximation of an interconnection yet small enough to allow the research team to investigate a large number of scenarios and sensitivity combinations. The research should prove useful to market designers, regulators, utilities, and others who want to better understand how system changes can affect production costs.« less

Simulation of hybrid propulsion system using LSRG and single cylinder engine

NASA Astrophysics Data System (ADS)

Han, C.; Ohyama, K.; Wang, W. Q.

2017-11-01

Nowadays, more and more people are beginning to use hybrid vehicles (HVs). The drive system of HVs needs to produce the electric energy with the electric generator and gearbox powered by an engine. Therefore, the structure becomes complex and the cost is high. To solve this issue, this research proposes a new drive system design that combines the engine and a linear switched reluctance generator (LSRG). When the engine is operating, the LSRG can simultaneously assist the engine’s mechanical output or can generate power to charge the battery. In this research, three research steps are executed. In the first step, the LSRG is designed according to the size of normal engine. Then, finite element analysis is used to get the data of flux linkage and calculate the inductance and translator force. Finally, Simulink models of control system are constructed to verify the performance of LSRG.

A Tesla-type repetitive nanosecond pulse generator for solid dielectric breakdown research.

PubMed

Zhao, Liang; Pan, Ya Feng; Su, Jian Cang; Zhang, Xi Bo; Wang, Li Min; Fang, Jin Peng; Sun, Xu; Lui, Rui

2013-10-01

A Tesla-type repetitive nanosecond pulse generator including a pair of electrode and a matched absorption resistor is established for the application of solid dielectric breakdown research. As major components, a built-in Tesla transformer and a gas-gap switch are designed to boost and shape the output pulse, respectively; the electrode is to form the anticipated electric field; the resistor is parallel to the electrode to absorb the reflected energy from the test sample. The parameters of the generator are a pulse width of 10 ns, a rise and fall time of 3 ns, and a maximum amplitude of 300 kV. By modifying the primary circuit of the Tesla transformer, the generator can produce both positive and negative pulses at a repetition rate of 1-50 Hz. In addition, a real-time measurement and control system is established based on the solid dielectric breakdown requirements for this generator. With this system, experiments on test samples made of common insulation materials in pulsed power systems are conducted. The preliminary experimental results show that the constructed generator is capable to research the solid dielectric breakdown phenomenon on a nanosecond time scale.

Measuring Performance with Library Automated Systems.

ERIC Educational Resources Information Center

OFarrell, John P.

2000-01-01

Investigates the capability of three library automated systems to generate some of the datasets necessary to form the ISO (International Standards Organization) standard on performance measurement within libraries, based on research in Liverpool John Moores University (United Kingdom). Concludes that the systems are weak in generating the…

Structural analysis and design for the development of floating photovoltaic energy generation system

NASA Astrophysics Data System (ADS)

Yoon, S. J.; Joo, H. J.; Kim, S. H.

2018-06-01

In this paper, we discussed the structural analysis and design for the development of floating photovoltaic energy generation system. Series of research conducted to develop the system from the analysis and design of the structural system to the installation of the system discussed. In the structural system supporting solar panels PFRP materials and SMC FRP materials used. A unit module structure is fabricated and then the unit module structures are connected each other to assemble whole PV energy generation complex. This system connected directly to the power grid system. In addition, extensive monitoring for the efficiency of electricity generation and the soundness of the structural system is in progress for the further system enhancement.

Study on the measures to promote the use of photovoltaic power generating system overseas

NASA Astrophysics Data System (ADS)

1989-03-01

In order to understand the state of the utilizing photovoltaic power generating system, the present situation to promote its development, the actual status of the assistance for developing countries by each country or by each international organization, research was done for USA, principal western countries, UN and EC. First, development conditions of the solar cell utilizing technique were classified by each country at the standpoint of developing and promoting systems. Second, the projects and policies in each country or international organization were arranged to promote research, development and introduction. Next, the present situation of the photovoltaic power generation projects by civilian parties and the problems to assist the projects by each country were arranged. While, the present sutuation of the photovoltaic power generation projects assisted by the governments and international organizations were classified by each country and each international organizations. Finally, in view of importance in the photovoltaic power generation project, it was concluded that not only developed country governments and international organizations but also private enterprises in developed countries were required to expand the understanding about the photovoltaic power generation system.

An Analysis of Elliptic Grid Generation Techniques Using an Implicit Euler Solver.

DTIC Science & Technology

1986-06-09

automatic determination of the control fu.nction, . elements of covariant metric tensor in the elliptic grid generation system , from the Cm = 1,2,3...computational fluid d’nan1-cs code. Tne code Inclues a tnree-dimensional current research is aimed primaril: at algebraic generation system based on transfinite...start the iterative solution of the f. ow, nea, transfer, and combustion proble:s. elliptic generation system . Tn13 feature also .:ven-.ts :.t be made

Human Category Learning 2.0

PubMed Central

Ashby, F. Gregory; Maddox, W. Todd

2010-01-01

During the 1990’s and early 2000’s, cognitive neuroscience investigations of human category learning focused on the primary goal of showing that humans have multiple category learning systems and on the secondary goals of identifying key qualitative properties of each system and of roughly mapping out the neural networks that mediate each system. Many researchers now accept the strength of the evidence supporting multiple systems, and as a result, during the past few years, work has begun on the second generation of research questions – that is, on questions that begin with the assumption that humans have multiple category learning systems. This article reviews much of this second generation of research. Topics covered include: 1) How do the various systems interact? 2) Are there different neural systems for categorization and category representation? 3) How does automaticity develop in each system?, and 4) Exactly how does each system learn? PMID:21182535

Human category learning 2.0.

PubMed

Ashby, F Gregory; Maddox, W Todd

2011-04-01

During the 1990s and early 2000s, cognitive neuroscience investigations of human category learning focused on the primary goal of showing that humans have multiple category-learning systems and on the secondary goals of identifying key qualitative properties of each system and of roughly mapping out the neural networks that mediate each system. Many researchers now accept the strength of the evidence supporting multiple systems, and as a result, during the past few years, work has begun on the second generation of research questions-that is, on questions that begin with the assumption that humans have multiple category-learning systems. This article reviews much of this second generation of research. Topics covered include (1) How do the various systems interact? (2) Are there different neural systems for categorization and category representation? (3) How does automaticity develop in each system? and (4) Exactly how does each system learn? © 2010 New York Academy of Sciences.

Virtual Inertia: Current Trends and Future Directions

DOE PAGES

Tamrakar, Ujjwol; Shrestha, Dipesh; Maharjan, Manisha; ...

2017-06-26

The modern power system is progressing from a synchronous machine-based system towards an inverter-dominated system, with a large-scale penetration of renewable energy sources (RESs) like wind and photovoltaics. RES units today represent a major share of the generation, and the traditional approach of integrating themas grid following units can lead to frequency instability. Many researchers have pointed towards using inverters with virtual inertia control algorithms so that they appear as synchronous generators to the grid, maintaining and enhancing system stability. Our paper presents a literature review of the current state-of-the-art of virtual inertia implementation techniques, and explores potential research directionsmore » and challenges. The major virtual inertia topologies are compared and classified. Through literature review and simulations of some selected topologies it has been shown that similar inertial response can be achieved by relating the parameters of these topologies through time constants and inertia constants, although the exact frequency dynamics may vary slightly. The suitability of a topology depends on system control architecture and desired level of detail in replication of the dynamics of synchronous generators. We present a discussion on the challenges and research directions which points out several research needs, especially for systems level integration of virtual inertia systems.« less

Virtual Inertia: Current Trends and Future Directions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tamrakar, Ujjwol; Shrestha, Dipesh; Maharjan, Manisha

The modern power system is progressing from a synchronous machine-based system towards an inverter-dominated system, with a large-scale penetration of renewable energy sources (RESs) like wind and photovoltaics. RES units today represent a major share of the generation, and the traditional approach of integrating themas grid following units can lead to frequency instability. Many researchers have pointed towards using inverters with virtual inertia control algorithms so that they appear as synchronous generators to the grid, maintaining and enhancing system stability. Our paper presents a literature review of the current state-of-the-art of virtual inertia implementation techniques, and explores potential research directionsmore » and challenges. The major virtual inertia topologies are compared and classified. Through literature review and simulations of some selected topologies it has been shown that similar inertial response can be achieved by relating the parameters of these topologies through time constants and inertia constants, although the exact frequency dynamics may vary slightly. The suitability of a topology depends on system control architecture and desired level of detail in replication of the dynamics of synchronous generators. We present a discussion on the challenges and research directions which points out several research needs, especially for systems level integration of virtual inertia systems.« less

Final report and recommendations for research on human-automation interaction in the Next Generation Air Transportation System

DOT National Transportation Integrated Search

2006-11-01

This is the final report of an 18-month project to: (1) review Next Generation Air Transportation System (NGATS) Joint Planning and Development Office (JPDO) documents as they pertain to human-automation interaction; (2) review past system failures i...

Airspace Systems Program: Next Generation Air Transportation System Concepts and Technology Development FY2010 Project Plan Version 3.0

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.

2010-01-01

This document describes the FY2010 plan for the management and execution of the Next Generation Air Transportation System (NextGen) Concepts and Technology Development (CTD) Project. The document was developed in response to guidance from the Airspace Systems Program (ASP), as approved by the Associate Administrator of the Aeronautics Research Mission Directorate (ARMD), and from guidelines in the Airspace Systems Program Plan. Congress established the multi-agency Joint Planning and Development Office (JPDO) in 2003 to develop a vision for the 2025 Next Generation Air Transportation System (NextGen) and to define the research required to enable it. NASA is one of seven agency partners contributing to the effort. Accordingly, NASA's ARMD realigned the Airspace Systems Program in 2007 to "directly address the fundamental research needs of the Next Generation Air Transportation System...in partnership with the member agencies of the JPDO." The Program subsequently established two new projects to meet this objective: the NextGen-Airspace Project and the NextGen-Airportal Project. Together, the projects will also focus NASA s technical expertise and world-class facilities to address the question of where, when, how and the extent to which automation can be applied to moving aircraft safely and efficiently through the NAS and technologies that address optimal allocation of ground and air technologies necessary for NextGen. Additionally, the roles and responsibilities of humans and automation influence in the NAS will be addressed by both projects. Foundational concept and technology research and development begun under the NextGen-Airspace and NextGen-Airportal projects will continue. There will be no change in NASA Research Announcement (NRA) strategy, nor will there be any change to NASA interfaces with the JPDO, Federal Aviation Administration (FAA), Research Transition Teams (RTTs), or other stakeholders

Design of Stand-Alone Hybrid Power Generation System at Brumbun Beach Tulungagung East Java

NASA Astrophysics Data System (ADS)

Rahmat, A. N.; Hidayat, M. N.; Ronilaya, F.; Setiawan, A.

2018-04-01

Indonesian government insists to optimize the use of renewable energy resources in electricity generation. One of the efforts is launching Independent Energy Village plan. This program aims to fulfill the need of electricity for isolated or remote villages in Indonesia. In order to support the penetration of renewable energy resources in electricity generation, a hybrid power generation system is developed. The simulation in this research is based on the availability of renewable energy resources in Brumbun beach, Tulungagung, East Java. Initially, the electricity was supplied through stand-alone electricity generations which are installed at each house. Hence, the use of electricity between 5 p.m. – 9 p.m. requires high operational costs. Based on the problem above, this research is conducted to design a stand-alone hybrid electricity generation system, which may consist of diesel, wind, and photovoltaic. The design is done by using HOMER software to optimize the use of electricity from renewable resources and to reduce the operation of diesel generation. The combination of renewable energy resources in electricity generation resulted in NPC of 44.680, COE of 0,268, and CO2 emissions of 0,038 % much lower than the use of diesel generator only.

Summary of NASA Lewis Research Center solar heating and cooling and wind energy programs

NASA Technical Reports Server (NTRS)

Vernon, R. W.

1975-01-01

Plans for the construction and operation of a solar heating and cooling system in conjunction with a office building being constructed at Langley Research Center, are discussed. Supporting research and technology includes: testing of solar collectors with a solar simulator, outdoor testing of collectors, property measurements of selective and nonselective coatings for solar collectors, and a solar model-systems test loop. The areas of a wind energy program that are being conducted include: design and operation of a 100-kW experimental wind generator, industry-designed and user-operated wind generators in the range of 50 to 3000 kW, and supporting research and technology for large wind energy systems. An overview of these activities is provided.

Motor/Generator and Inverter Characterization for Flywheel System Applications

NASA Technical Reports Server (NTRS)

Tamarcus, Jeffries L.

2004-01-01

The Advanced Electrical Systems Development Branch at NASA Glenn Research Center (GRC) has been involved in the research and development of high speed flywheels systems for satellite energy storage and attitude applications. These flywheels will serve as replacement for chemical nickel hydrogen, nickel cadmium batteries and gyroscopic wheels. The advantages of using flywheel systems for energy storage on satellites are high energy density, high power density, long life, deep depth of discharge, and broad operating temperature ranges. A flywheel system for space applications consist of a number of flywheel modules, the motor/generator and magnetic bearing, and an electronics package. The motor/generator electronics package includes a pulse-width modulated inverter that drives the flywheel permanent magnet motor/generator located at one end of the shaft. This summer, I worked under the direct supervision of my mentor, Walter Santiago, and the goal for this summer was to characterize motor generator and inverter attributes in order to increase their viability as a more efficient energy storage source for space applications. To achieve this goal, magnetic field measurements around the motor/generator permanent magnet and the impedance of the motor/generator three phase windings were characterized, and a recreation of the inverter pulse width modulated control system was constructed. The Flywheel modules for space use are designed to maximize energy density and minimize loss, and attaining these values will aid in locating and reducing losses within the flywheel system as a whole, making flywheel technology more attractive for use as energy storage in future space applications.

Waveform Generator Signal Processing Software

DOT National Transportation Integrated Search

1988-09-01

This report describes the software that was developed to process test waveforms that were recorded by crash test data acquisition systems. The test waveforms are generated by an electronic waveform generator developed by MGA Research Corporation unde...

Research and technology, Lewis Research Center

NASA Technical Reports Server (NTRS)

1982-01-01

Aeronautics, space, and terrestrial energy research is covered. Energy conversion processes and systems for propulsion in the atmosphere, in space, and on the ground are reviewed. Electric energy generation and storage for both terrestrial and space applications and materials and structures for such systems are also reviewed.

Knowledge-Based Entrepreneurship in a Boundless Research System

ERIC Educational Resources Information Center

Dell'Anno, Davide

2008-01-01

International entrepreneurship and knowledge-based entrepreneurship have recently generated considerable academic and non-academic attention. This paper explores the "new" field of knowledge-based entrepreneurship in a boundless research system. Cultural barriers to the development of business opportunities by researchers persist in some academic…

Using global unique identifiers to link autism collections.

PubMed

Johnson, Stephen B; Whitney, Glen; McAuliffe, Matthew; Wang, Hailong; McCreedy, Evan; Rozenblit, Leon; Evans, Clark C

2010-01-01

To propose a centralized method for generating global unique identifiers to link collections of research data and specimens. The work is a collaboration between the Simons Foundation Autism Research Initiative and the National Database for Autism Research. The system is implemented as a web service: an investigator inputs identifying information about a participant into a client application and sends encrypted information to a server application, which returns a generated global unique identifier. The authors evaluated the system using a volume test of one million simulated individuals and a field test on 2000 families (over 8000 individual participants) in an autism study. Inverse probability of hash codes; rate of false identity of two individuals; rate of false split of single individual; percentage of subjects for which identifying information could be collected; percentage of hash codes generated successfully. Large-volume simulation generated no false splits or false identity. Field testing in the Simons Foundation Autism Research Initiative Simplex Collection produced identifiers for 96% of children in the study and 77% of parents. On average, four out of five hash codes per subject were generated perfectly (only one perfect hash is required for subsequent matching). The system must achieve balance among the competing goals of distinguishing individuals, collecting accurate information for matching, and protecting confidentiality. Considerable effort is required to obtain approval from institutional review boards, obtain consent from participants, and to achieve compliance from sites during a multicenter study. Generic unique identifiers have the potential to link collections of research data, augment the amount and types of data available for individuals, support detection of overlap between collections, and facilitate replication of research findings.

Measurement framework for product service system performance of generator set distributors

NASA Astrophysics Data System (ADS)

Sofianti, Tanika D.

2017-11-01

Selling Generator Set (Genset) in B2B market, distributors assisted manufacturers to sell products. This is caused by the limited resources owned by the manufacturer for adding service elements. These service elements are needed to enhance the competitiveness of the generator sets. Some genset distributors often sell products together with supports to their customers. Industrial distributor develops services to meet the needs of the customer. Generator set distributors support machines and equipment produced by manufacturer. The services delivered by the distributors could enhance value obtained by the customers from the equipment. Services provided to customers in bidding process, ordering process of the equipment from the manufacturer, equipment delivery, installations, and the after sales stage. This paper promotes framework to measure Product Service System (PSS) of Generator Set distributors in delivering their products and services for the customers. The methodology of conducting this research is by adopting the perspective of the providers and customers and by taking into account the tangible and intangible products. This research leads to the idea of improvement of current Product Service System of a Genset distributor. This research needs further studies in more detailed measures and the implementation of measurement tools.

A Summary of NASA Research Exploring the Acoustics of Small Unmanned Aerial Systems

NASA Technical Reports Server (NTRS)

Zawodny, Nikolas S.; Christian, Andrew; Cabell, Randolph

2018-01-01

Proposed uses of small unmanned aerial systems (sUAS) have the potential to expose large portions of communities to a new noise source. In order to understand the potential noise impact of sUAS, NASA initiated acoustics research as one component of the 3-year DELIVER project, with the goal of documenting the feasibility of using existing aircraft design tools and methods on this class of vehicles. This paper summarizes the acoustics research conducted within the DELIVER project. The research described here represents an initial study, and subsequent research building on the findings of this work has been proposed for other NASA projects. The paper summarizes acoustics research in four areas: measurements of noise generated by flyovers of small unmanned aerial vehicles, measurements in controlled test facilities to understand the noise generated by components of these vehicles, computational predictions of component and full vehicle noise, and psychoacoustic tests including auralizations conducted to assess human annoyance to the noise generated by these vehicles.

Your Co-author Received 150 Citations: Pride, but Not Envy, Mediates the Effect of System-Generated Achievement Messages on Motivation.

PubMed

Utz, Sonja; Muscanell, Nicole L

2018-01-01

ResearchGate, a social network site for academics, prominently displays the achievements of people one follows ("With 150 new reads, X was the most read author from their institute"). The goal of this paper was to examine the emotional and motivational effects of these system-generated messages, thereby extending prior research on envy-evoking status updates on Facebook to a professional context. We also extend the research on social comparisons and more broadly, on emotional responses elicited by social media. Specifically, social media research has largely focused on examining emotional reactions to content that is both generated by and is about others. In this research we directly examine updates generated by the system (ResearchGate) while also directly comparing reactions to updates about others' achievements with reactions to updates that are about the self-i.e., one's personal achievements which are also displayed on ResearchGate ("With 150 new reads, you were the most read author from your institute"). Particular attention was paid to the mediating role of envy and pride. The results of our quasi-experimental field study ( n = 419) showed that the achievements of others elicited envy, whereas personal achievements elicited pride. People exposed to their personal achievements (vs. the achievement of others) showed a higher motivation to work harder. This effect was mediated by pride, but not envy. The theoretical and practical implications of these findings are discussed.

Your Co-author Received 150 Citations: Pride, but Not Envy, Mediates the Effect of System-Generated Achievement Messages on Motivation

PubMed Central

Utz, Sonja; Muscanell, Nicole L.

2018-01-01

ResearchGate, a social network site for academics, prominently displays the achievements of people one follows (“With 150 new reads, X was the most read author from their institute”). The goal of this paper was to examine the emotional and motivational effects of these system-generated messages, thereby extending prior research on envy-evoking status updates on Facebook to a professional context. We also extend the research on social comparisons and more broadly, on emotional responses elicited by social media. Specifically, social media research has largely focused on examining emotional reactions to content that is both generated by and is about others. In this research we directly examine updates generated by the system (ResearchGate) while also directly comparing reactions to updates about others’ achievements with reactions to updates that are about the self—i.e., one’s personal achievements which are also displayed on ResearchGate (“With 150 new reads, you were the most read author from your institute”). Particular attention was paid to the mediating role of envy and pride. The results of our quasi-experimental field study (n = 419) showed that the achievements of others elicited envy, whereas personal achievements elicited pride. People exposed to their personal achievements (vs. the achievement of others) showed a higher motivation to work harder. This effect was mediated by pride, but not envy. The theoretical and practical implications of these findings are discussed. PMID:29780339

Different Patterns of Student-Faculty Interaction in Research Universities: An Analysis by Student Gender, Race, SES, and First-Generation Status. A Student Experience in the Research University (SERU) Project Research Paper. Research & Occasional Paper Series: CSHE.10.07

ERIC Educational Resources Information Center

Kim, Young K.; Sax, Linda J.

2007-01-01

This study examined the conditional effects of student-faculty interaction in a large research university system, based on various student characteristics including gender, race, and socio-economic and first-generation status. The study utilized data from the 2006 University of California Undergraduate Experience Survey (UCUES), a longitudinal…

Perform Experiments on LINUS-O and LTX Imploding Liquid Liner Fusion Systems.

DTIC Science & Technology

1982-08-27

EXPERIMENTS .. .. .. ... 3 III. HOMOPOLAR GENERATOR/INDUCTOR POWER SUPPLY EXPERIMENTS. 11 IV. PLASMA SWITCH EXPERIMENTS. .. .. .. .... . ..... 18 V... homopolar generator (HPG) inductive load system. 0 Conduct an electromagnetic pulse (EMP) simulation demonstration using the NRL HPG/inductive storage...suggest solutions to the unstable flow problem, the research was suspended due to the program redirection. -10- IT III. HOMOPOLAR GENERATOR/INDUCTOR POWER

Multilingual Generalization of the ModelCreator Software for Math Item Generation. Research Report. ETS RR-05-02

ERIC Educational Resources Information Center

Higgins, Derrick; Futagi, Yoko; Deane, Paul

2005-01-01

This paper reports on the process of modifying the ModelCreator item generation system to produce output in multiple languages. In particular, Japanese and Spanish are now supported in addition to English. The addition of multilingual functionality was considerably facilitated by the general formulation of our natural language generation system,…

A Computer Program for the Generation of ARIMA Data

ERIC Educational Resources Information Center

Green, Samuel B.; Noles, Keith O.

1977-01-01

The autoregressive integrated moving averages model (ARIMA) has been applied to time series data in psychological and educational research. A program is described that generates ARIMA data of a known order. The program enables researchers to explore statistical properties of ARIMA data and simulate systems producing time dependent observations.…

Maturing Technologies for Stirling Space Power Generation

NASA Technical Reports Server (NTRS)

Wilson, Scott D.; Nowlin, Brentley C.; Dobbs, Michael W.; Schmitz, Paul C.; Huth, James

2016-01-01

Stirling Radioisotope Power Systems (RPS) are being developed as an option to provide power on future space science missions where robotic spacecraft will orbit, flyby, land or rove. A Stirling Radioisotope Generator (SRG) could offer space missions a more efficient power system that uses one fourth of the nuclear fuel and decreases the thermal footprint of the current state of the art. The RPS Program Office, working in collaboration with the U.S. Department of Energy (DOE), manages projects to develop thermoelectric and dynamic power systems, including Stirling Radioisotope Generators (SRGs). The Stirling Cycle Technology Development (SCTD) Project, located at Glenn Research Center (GRC), is developing Stirling-based subsystems, including convertors and controllers. The SCTD Project also performs research that focuses on a wide variety of objectives, including increasing convertor temperature capability to enable new environments, improving system reliability or fault tolerance, reducing mass or size, and developing advanced concepts that are mission enabling. Research activity includes maturing subsystems, assemblies, and components to prepare them for infusion into future convertor and generator designs. The status of several technology development efforts are described here. As part of the maturation process, technologies are assessed for readiness in higher-level subsystems. To assess the readiness level of the Dual Convertor Controller (DCC), a Technology Readiness Assessment (TRA) was performed and the process and results are shown. Stirling technology research is being performed by the SCTD Project for NASA's RPS Program Office, where tasks focus on maturation of Stirling-based systems and subsystems for future space science missions.

Thermophotovoltaic systems for civilian and industrial applications in Japan

NASA Astrophysics Data System (ADS)

Yugami, Hiroo; Sasa, Hiromi; Yamaguchi, Masafumi

2003-05-01

The potential market for thermophotovoltaic (TPV) applications has been studied for civilian and industrial sectors in Japan. Comparing the performance of gas engines or turbines, as well as the underdeveloped power generation technologies such as fuel cells or chemical batteries, we have discussed the feasible application field of TPV systems to compete with those power generations. From the point of view of applicability for TPV systems in Japan, portable generators, co-generation systems and solar power plants are selected for our system analysis. The cost and performance targets of TPV systems for co-generation are also discussed by assuming a typical daily profile of electricity and hot water demands in Japanese homes. A progress report on the recent TPV research activities is given as well as a feasibility study concerning such TPV systems in Japan.

Prototype Software for Future Spaceflight Tested at Mars Desert Research Station

NASA Technical Reports Server (NTRS)

Clancey, William J.; Sierhuis, Maaretn; Alena, Rick; Dowding, John; Garry, Brent; Scott, Mike; Tompkins, Paul; vanHoof, Ron; Verma, Vandi

2006-01-01

NASA scientists in MDRS Crew 49 (April 23-May 7, 2006) field tested and significantly extended a prototype monitoring and advising system that integrates power system telemetry with a voice commanding interface. A distributed, wireless network of functionally specialized agents interacted with the crew to provide alerts (e.g., impending shut-down of inverter due to low battery voltage), access md interpret historical data, and display troubleshooting procedures. In practical application during two weeks, the system generated speech over loudspeakers and headsets lo alert the crew about the need to investigate power system problems. The prototype system adapts the Brahms/Mobile Agents toolkit to receive data from the OneMeter (Brand Electronics) electric metering system deployed by Crew 47. A computer on the upper deck was connected to loudspeakers, four others were paired with wireless (Bluetooth) headsets that enabled crew members to interact with their personal agents from anywhere in the hab. Voice commands and inquiries included: 1. What is the {battery | generator} {volts | amps | volts and amps}? 2. What is the status of the {generator | inverter | battery | solar panel}? 3. What is the hab{itat} {power usage | volts | voltage | amps | volts and amps}? 4. What was the average hab{itat} {amps | volts | voltage} since <#> {AM | PM)? 5. When did the {generator | batteries} change status? 6. Tell {me I | everyone} when{ ever} the generator goes offline. 7. Tell {me | | everyone} when the hab{itat} {amps | volts | voltage} {exceeds | drops brelow} <#>. 8. {Send | Take | Record} {a} voice note {(for | to} } {at }. This research demonstrates the principles of design in the context of use, investigating requirements through experimental use of prototype systems in an analog setting, and use of MDRS as a research facility for designing and implementing new systems.

GREEN CATALYZED OXIDATION OF HYDROCARBONS IN ALTERNATIVE SOLVENT SYSTEMS GENERATED BY PARIS II

EPA Science Inventory

Green Catalyzed Oxidation of Hydrocarbons in Alternative Solvent Systems Generated by PARIS II

Michael A. Gonzalez*, Thomas M. Becker, and Paul F. Harten; Sustainable Technology Division, Office of Research and Development; United States Environmental Protection Agency, 26...

Research and Improvement on Characteristics of Emergency Diesel Generating Set Mechanical Support System in Nuclear Power Plant

NASA Astrophysics Data System (ADS)

Zhe, Yang

2017-06-01

There are often mechanical problems of emergency power generation units in nuclear power plant, which bring a great threat to nuclear safety. Through analyzing the influence factors caused by mechanical failure, the existing defects of the design of mechanical support system are determined, and the design idea has caused the direction misleading in the field of maintenance and transformation. In this paper, research analysis is made on basic support design of diesel generator set, main pipe support design and important components of supercharger support design. And this paper points out the specific design flaws and shortcomings, and proposes targeted improvement program. Through the implementation of improvement programs, vibration level of unit and mechanical failure rate are reduced effectively. At the same time, it also provides guidance for design, maintenance and renovation of diesel generator mechanical support system of nuclear power plants in the future.

Feasibility of encoding the Institute for Clinical Systems Improvement Depression Guideline using the Omaha System.

PubMed

Monsen, Karen A; Neely, Claire; Oftedahl, Gary; Kerr, Madeleine J; Pietruszewski, Pam; Farri, Oladimeji

2012-08-01

Evidence-based clinical guidelines are being developed to bridge the gap between research and practice with the goals of improving health care quality and population health. However, disseminating, implementing, and ensuring ongoing use of clinical guidelines in practice settings is challenging. The purpose of this study was to demonstrate the feasibility of encoding evidence-based clinical guidelines using the Omaha System. Clinical documentation with Omaha System-encoded guidelines generates individualized, meaningful data suitable for program evaluation and health care quality research. The use of encoded guidelines within the electronic health record has potential to reinforce use of guidelines, and thus improve health care quality and population health. Research using Omaha System data generated by clinicians has potential to discover new knowledge related to guideline use and effectiveness. Copyright © 2012 Elsevier Inc. All rights reserved.

Lightweight application for generating clinical research information systems: MAGIC.

PubMed

Leskošek, Brane; Pajntar, Marjan

2015-12-01

Our purpose was to build and test a lightweight solution for generating clinical research information systems (CRIS) that would allow non-IT professionals with basic knowledge of computer usage to quickly define and build a ready-to-use, safe and secure web-based clinical research system for data management. We use the acronym MAGIC (Medical Application Generator InteraCtive) for the system. The generated CRIS should be very easy to build and use, so a common LAMP (Linux Apache MySQL Perl) platform was used, which also enables short development cycles. The application was built and tested using eXtreme Programming (XP) principles by a small development team consisting of one informatics specialist, one physician and one graphical designer/programmer. The parameter and graphical user interface (GUI) definitions for the CRIS can be made by non-IT professionals using an intuitive English-language-like formalism called application definition language (ADL). From these definitions, the MAGIC builds an end-user CRIS that can be used on a wide variety of platforms (from standard workstations to hand-held devices). A working example of a national health-care-quality assessment program is presented to illustrate this process. The lightweight application for generating CRIS (MAGIC) has proven to be useful for both clinical and analytical users in real working environment. To achieve better performance and interoperability, we are planning to recompile the application using XML schemas (XSD) in HL7 CDA or openEHR archetypes formats used for parameters definition and for data interchange between different information systems.

Future trends in power generation cost by power resource

NASA Astrophysics Data System (ADS)

1992-08-01

The Japan Energy Economy Research Institute has been evaluating power generation cost by each power resource every year focusing on nuclear power generation. The Institute is surveying the cost evaluations by power resources in France, Britain and the U.S.A., the nuclear generation advanced nations. The OECD is making power generation cost estimation using a hypothesis which uniforms basically the conditions varying in different member countries. In model power generation cost calculations conducted by the Ministry of International Trade and Industry of Japan, nuclear power generation is the most economical system in any fiscal year. According to recent calculations performed by the Japan Energy Economy Research Institute, the situation is such that it is difficult to distinguish the economical one from others among the power generation systems in terms of generation costs except for thermal power generation. Economic evaluations are given on estimated power generation costs based on construction costs for nuclear and thermal power plants, nuclear fuel cycling cost, and fuel cost data on petroleum, LNG and coal. With regard to the future trends, scenario analyses are made on generation costs, that assume fluctuations in fuel prices and construction costs, the important factors to give economic influence on power generation.

Environmental Impacts of Renewable Electricity Generation Technologies: A Life Cycle Perspective

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heath, Garvin

2016-01-13

All energy systems impact the environment. Much has been learned about these environmental impacts from decades of research. Through systematic reviews, meta-analysis and original research, the National Renewable Energy Laboratory has been building knowledge about environmental impacts of both renewable and conventional electricity generation technologies. Evidence for greenhouse gas emissions, water and land use will be reviewed mostly from the perspective of life cycle assessment. Impacts from oil and natural gas systems will be highlighted. Areas of uncertainty and challenge will be discussed as suggestions for future research, as well as career opportunities in this field.

Optimal control for wind turbine system via state-space method

NASA Astrophysics Data System (ADS)

Shanoob, Mudhafar L.

Renewable energy is becoming a fascinating research interest in future energy production because it is green and does not pollute nature. Wind energy is an excellent example of renewable resources that are evolving. Throughout the history of humanity, wind energy has been used. In ancient time, it was used to grind seeds, sailing etc. Nowadays, wind energy has been used to generate electrical power. Researchers have done a lot of research about using a wind source to generate electricity. As wind flow is not reliable, there is a challenge to get stable electricity out of this varying wind. This problem leads to the use of different control methods and the optimization of these methods to get a stable and reliable electrical energy. In this research, a wind turbine system is considered to study the transient and the steady-state stability; consisting of the aerodynamic system, drive train and generator. The Doubly Feed Induction Generator (DFIG) type generator is used in this thesis. The wind turbine system is connected to power system network. The grid is an infinite bus bar connected to a short transmission line and transformer. The generator is attached to the grid from the stator side. State-space method is used to model the wind turbine parts. The system is modeled and controlled using MATLAB/Simulation software. First, the current-mode control method (PVdq) with (PI) regulator is operated as a reference to find how the system reacts to an unexpected disturbance on the grid side or turbine side. The controller is operated with three scenarios of disruption: Disturbance-mechanical torque input, Step disturbance in the electrical torque reference and Fault Ride-through. In the simulation results, the time response and the transient stability of the system is a product of the disturbances that take a long time to settle. So, for this reason, Linear Quadratic Regulation (LQR) optimal control is utilized to solve this problem. The LQR method is designed based on using type 1 servo system that depends on the full state feedback variables and tracking error. The LQR improves the transient stability and time response of the wind turbine system in all three-disturbance scenarios. The results of both methods are deeply explained in the simulation section.

Next Generation CAD/CAM/CAE Systems

NASA Technical Reports Server (NTRS)

Noor, Ahmed K. (Compiler); Malone, John B. (Compiler)

1997-01-01

This document contains presentations from the joint UVA/NASA Workshop on Next Generation CAD/CAM/CAE Systems held at NASA Langley Research Center in Hampton, Virginia on March 18-19, 1997. The presentations focused on current capabilities and future directions of CAD/CAM/CAE systems, aerospace industry projects, and university activities related to simulation-based design. Workshop attendees represented NASA, commercial software developers, the aerospace industry, government labs, and academia. The workshop objectives were to assess the potential of emerging CAD/CAM/CAE technology for use in intelligent simulation-based design and to provide guidelines for focused future research leading to effective use of CAE systems for simulating the entire life cycle of aerospace systems.

Real-time high speed generator system emulation with hardware-in-the-loop application

NASA Astrophysics Data System (ADS)

Stroupe, Nicholas

The emerging emphasis and benefits of distributed generation on smaller scale networks has prompted much attention and focus to research in this field. Much of the research that has grown in distributed generation has also stimulated the development of simulation software and techniques. Testing and verification of these distributed power networks is a complex task and real hardware testing is often desired. This is where simulation methods such as hardware-in-the-loop become important in which an actual hardware unit can be interfaced with a software simulated environment to verify proper functionality. In this thesis, a simulation technique is taken one step further by utilizing a hardware-in-the-loop technique to emulate the output voltage of a generator system interfaced to a scaled hardware distributed power system for testing. The purpose of this thesis is to demonstrate a new method of testing a virtually simulated generation system supplying a scaled distributed power system in hardware. This task is performed by using the Non-Linear Loads Test Bed developed by the Energy Conversion and Integration Thrust at the Center for Advanced Power Systems. This test bed consists of a series of real hardware developed converters consistent with the Navy's All-Electric-Ship proposed power system to perform various tests on controls and stability under the expected non-linear load environment of the Navy weaponry. This test bed can also explore other distributed power system research topics and serves as a flexible hardware unit for a variety of tests. In this thesis, the test bed will be utilized to perform and validate this newly developed method of generator system emulation. In this thesis, the dynamics of a high speed permanent magnet generator directly coupled with a micro turbine are virtually simulated on an FPGA in real-time. The calculated output stator voltage will then serve as a reference for a controllable three phase inverter at the input of the test bed that will emulate and reproduce these voltages on real hardware. The output of the inverter is then connected with the rest of the test bed and can consist of a variety of distributed system topologies for many testing scenarios. The idea is that the distributed power system under test in hardware can also integrate real generator system dynamics without physically involving an actual generator system. The benefits of successful generator system emulation are vast and lead to much more detailed system studies without the draw backs of needing physical generator units. Some of these advantages are safety, reduced costs, and the ability of scaling while still preserving the appropriate system dynamics. This thesis will introduce the ideas behind generator emulation and explain the process and necessary steps to obtaining such an objective. It will also demonstrate real results and verification of numerical values in real-time. The final goal of this thesis is to introduce this new idea and show that it is in fact obtainable and can prove to be a highly useful tool in the simulation and verification of distributed power systems.

Large, horizontal-axis wind turbines

NASA Technical Reports Server (NTRS)

Linscott, B. S.; Perkins, P.; Dennett, J. T.

1984-01-01

Development of the technology for safe, reliable, environmentally acceptable large wind turbines that have the potential to generate a significant amount of electricity at costs competitive with conventional electric generating systems are presented. In addition, these large wind turbines must be fully compatible with electric utility operations and interface requirements. There are several ongoing large wind system development projects and applied research efforts directed toward meeting the technology requirements for utility applications. Detailed information on these projects is provided. The Mod-O research facility and current applied research effort in aerodynamics, structural dynamics and aeroelasticity, composite and hybrid composite materials, and multiple system interaction are described. A chronology of component research and technology development for large, horizontal axis wind turbines is presented. Wind characteristics, wind turbine economics, and the impact of wind turbines on the environment are reported. The need for continued wind turbine research and technology development is explored. Over 40 references are sited and a bibliography is included.

Research implementation of the SMART SIGNAL system on Trunk Highway (TH) 13.

DOT National Transportation Integrated Search

2013-02-01

In our previous research, the SMART-SIGNAL (Systematic Monitoring of Arterial Road Traffic and Signals) : system that can collect event-based traffic data and generate comprehensive performance measures has been : successfully developed by the Univer...

Educational Research and Theory Perspectives on Intelligent Computer-Assisted Instruction.

ERIC Educational Resources Information Center

Tennyson, Robert D.; Christensen, Dean L.

This paper defines the next generation of intelligent computer-assisted instructional systems (ICAI) by depicting the elaborations and extensions offered by educational research and theory perspectives to enhance the ICAI environment. The first section describes conventional ICAI systems, which use expert systems methods and have three modules: a…

Research on unit commitment with large-scale wind power connected power system

NASA Astrophysics Data System (ADS)

Jiao, Ran; Zhang, Baoqun; Chi, Zhongjun; Gong, Cheng; Ma, Longfei; Yang, Bing

2017-01-01

Large-scale integration of wind power generators into power grid brings severe challenges to power system economic dispatch due to its stochastic volatility. Unit commitment including wind farm is analyzed from the two parts of modeling and solving methods. The structures and characteristics can be summarized after classification has been done according to different objective function and constraints. Finally, the issues to be solved and possible directions of research and development in the future are discussed, which can adapt to the requirements of the electricity market, energy-saving power generation dispatching and smart grid, even providing reference for research and practice of researchers and workers in this field.

Coupled Research in Ocean Acoustics and Signal Processing for the Next Generation of Underwater Acoustic Communication Systems

DTIC Science & Technology

2016-08-05

JPAnalytics LLC CC: DCMA Boston DTIC Director, NRL Progress Report #8 Coupled Research in Ocean Acoustics and Signal Processing for the Next...Generation of Underwater Acoustic Communication Systems Principal Investigator’s Name: Dr. James Preisig Period Covered By Report: 1/20/2016 to 4/19/2016...Technical work this period has spanned two areas. The first of these is VHF Acoustics . During this time period, the Principle Investigator worked with Dr

Automated Test Case Generator for Phishing Prevention Using Generative Grammars and Discriminative Methods

ERIC Educational Resources Information Center

Palka, Sean

2015-01-01

This research details a methodology designed for creating content in support of various phishing prevention tasks including live exercises and detection algorithm research. Our system uses probabilistic context-free grammars (PCFG) and variable interpolation as part of a multi-pass method to create diverse and consistent phishing email content on…

Fault Injection and Monitoring Capability for a Fault-Tolerant Distributed Computation System

NASA Technical Reports Server (NTRS)

Torres-Pomales, Wilfredo; Yates, Amy M.; Malekpour, Mahyar R.

2010-01-01

The Configurable Fault-Injection and Monitoring System (CFIMS) is intended for the experimental characterization of effects caused by a variety of adverse conditions on a distributed computation system running flight control applications. A product of research collaboration between NASA Langley Research Center and Old Dominion University, the CFIMS is the main research tool for generating actual fault response data with which to develop and validate analytical performance models and design methodologies for the mitigation of fault effects in distributed flight control systems. Rather than a fixed design solution, the CFIMS is a flexible system that enables the systematic exploration of the problem space and can be adapted to meet the evolving needs of the research. The CFIMS has the capabilities of system-under-test (SUT) functional stimulus generation, fault injection and state monitoring, all of which are supported by a configuration capability for setting up the system as desired for a particular experiment. This report summarizes the work accomplished so far in the development of the CFIMS concept and documents the first design realization.

FY2017 Advanced Combustion Systems and Fuels Annual Progress Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

The Advanced Combustion Systems and Fuels Program supports VTO’s goal and focuses early-stage research and development (R&D) to improve understanding of the combustion processes, fuel properties, and emission control technologies while generating knowledge and insight necessary for industry to develop the next generation of engines.

Montana | Solar Research | NREL

Science.gov Websites

offers low-interest loans, corporate and personal tax credits, and property tax exemptions and reductions 35% against personal or corporate tax on the income generated by the investment. This credit is systems and can be availed for 10 years after installation of the system. Generation Facility Corporate

NEW VERSATILE AEROSOL GENERATION SYSTEM DEVELOPED FOR USE IN A LARGE WIND TUNNEL

EPA Science Inventory

A new aerosol generation system was developed to accommodate a variety of research activities performed within a large wind tunnel. Because many of the velocity measurements are taken in the wind tunnel with a laser Doppler anemometer (LDA), it is necessary to maintain an aero...

Power control and management of the grid containing largescale wind power systems

NASA Astrophysics Data System (ADS)

Aula, Fadhil Toufick

The ever increasing demand for electricity has driven many countries toward the installation of new generation facilities. However, concerns such as environmental pollution and global warming issues, clean energy sources, high costs associated with installation of new conventional power plants, and fossil fuels depletion have created many interests in finding alternatives to conventional fossil fuels for generating electricity. Wind energy is one of the most rapidly growing renewable power sources and wind power generations have been increasingly demanded as an alternative to the conventional fossil fuels. However, wind power fluctuates due to variation of wind speed. Therefore, large-scale integration of wind energy conversion systems is a threat to the stability and reliability of utility grids containing these systems. They disturb the balance between power generation and consumption, affect the quality of the electricity, and complicate load sharing and load distribution managing and planning. Overall, wind power systems do not help in providing any services such as operating and regulating reserves to the power grid. In order to resolve these issues, research has been conducted in utilizing weather forecasting data to improve the performance of the wind power system, reduce the influence of the fluctuations, and plan power management of the grid containing large-scale wind power systems which consist of doubly-fed induction generator based energy conversion system. The aims of this research, my dissertation, are to provide new methods for: smoothing the output power of the wind power systems and reducing the influence of their fluctuations, power managing and planning of a grid containing these systems and other conventional power plants, and providing a new structure of implementing of latest microprocessor technology for controlling and managing the operation of the wind power system. In this research, in order to reduce and smooth the fluctuations, two methods are presented. The first method is based on a de-loaded technique while the other method is based on utilizing multiple storage facilities. The de-loaded technique is based on characteristics of the power of a wind turbine and estimation of the generated power according to weather forecasting data. The technique provides a reference power by which the wind power system will operate and generate a smooth power. In contrast, utilizing storage facilities will allow the wind power system to operate at its maximum tracking power points' strategy. Two types of energy storages are considered in this research, battery energy storage system (BESS) and pumped-hydropower storage system (PHSS), to suppress the output fluctuations and to support the wind power system to follow the system load demands. Furthermore, this method provides the ability to store energy when there is a surplus of the generated power and to reuse it when there is a shortage of power generation from wind power systems. Both methods are new in terms of utilizing of the techniques and wind speed data. A microprocessor embedded system using an IntelRTM Atom(TM) processor is presented for controlling the wind power system and for providing the remote communication for enhancing the operation of the individual wind power system in a wind farm. The embedded system helps the wind power system to respond and to follow the commands of the central control of the power system. Moreover, it enhances the performance of the wind power system through self-managing, self-functioning, and self-correcting. Finally, a method of system power management and planning is modeled and studied for a grid containing large-scale wind power systems. The method is based on a new technique through constructing a new load demand curve (NLDC) from merging the estimation of generated power from wind power systems and forecasting of the load. To summarize, the methods and their results presented in this dissertation, enhance the operation of the large-scale wind power systems and reduce their drawbacks on the operation of the power grid.

Faculty Rank System, Research Motivation, and Faculty Research Productivity: Measure Refinement and Theory Testing.

ERIC Educational Resources Information Center

Tien, Flora F.; Blackburn, Robert T.

1996-01-01

A study explored the relationship between the traditional system of college faculty rank and faculty research productivity from the perspectives of behavioral reinforcement theory and selection function. Six hypotheses were generated and tested, using data from a 1989 national faculty survey. Results failed to support completely either the…

Portable multispectral imaging system for oral cancer diagnosis

NASA Astrophysics Data System (ADS)

Hsieh, Yao-Fang; Ou-Yang, Mang; Lee, Cheng-Chung

2013-09-01

This study presents the portable multispectral imaging system that can acquire the image of specific spectrum in vivo for oral cancer diagnosis. According to the research literature, the autofluorescence of cells and tissue have been widely applied to diagnose oral cancer. The spectral distribution is difference for lesions of epithelial cells and normal cells after excited fluorescence. We have been developed the hyperspectral and multispectral techniques for oral cancer diagnosis in three generations. This research is the third generation. The excited and emission spectrum for the diagnosis are acquired from the research of first generation. The portable system for detection of oral cancer is modified for existing handheld microscope. The UV LED is used to illuminate the surface of oral cavity and excite the cells to produce fluorescent. The image passes through the central channel and filters out unwanted spectrum by the selection of filter, and focused by the focus lens on the image sensor. Therefore, we can achieve the specific wavelength image via fluorescence reaction. The specificity and sensitivity of the system are 85% and 90%, respectively.

An update of engine system research at the Army Propulsion Directorate

NASA Technical Reports Server (NTRS)

Bobula, George A.

1990-01-01

The Small Turboshaft Engine Research (STER) program provides a vehicle for evaluating the application of emerging technologies to Army turboshaft engine systems and to investigate related phenomena. Capitalizing on the resources at hand, in the form of both the NASA facilities and the Army personnel, the program goal of developing a physical understanding of engine system dynamics and/or system interactions is being realized. STER entries investigate concepts and components developed both in-house and out-of-house. Emphasis is placed upon evaluations which have evolved from on-going basic research and advanced development programs. Army aviation program managers are also encouraged to make use of STER resources, both people and facilities. The STER personnel have established their reputations as experts in the fields of engine system experimental evaluations and engine system related phenomena. The STER facility has demonstrated its utility in both research and development programs. The STER program provides the Army aviation community the opportunity to perform system level investigations, and then to offer the findings to the entire engine community for their consideration in next generation propulsion systems. In this way results of the fundamental research being conducted to meet small turboshaft engine technology challenges expeditiously find their way into that next generation of propulsion systems.

Modeling and Simulation of U-tube Steam Generator

NASA Astrophysics Data System (ADS)

Zhang, Mingming; Fu, Zhongguang; Li, Jinyao; Wang, Mingfei

2018-03-01

The U-tube natural circulation steam generator was mainly researched with modeling and simulation in this article. The research is based on simuworks system simulation software platform. By analyzing the structural characteristics and the operating principle of U-tube steam generator, there are 14 control volumes in the model, including primary side, secondary side, down channel and steam plenum, etc. The model depends completely on conservation laws, and it is applied to make some simulation tests. The results show that the model is capable of simulating properly the dynamic response of U-tube steam generator.

Testing of the Advanced Stirling Radioisotope Generator Engineering Unit at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Lewandowski, Edward J.

2013-01-01

The Advanced Stirling Radioisotope Generator (ASRG) is a high-efficiency generator being developed for potential use on a Discovery 12 space mission. Lockheed Martin designed and fabricated the ASRG Engineering Unit (EU) under contract to the Department of Energy. This unit was delivered to NASA Glenn Research Center in 2008 and has been undergoing extended operation testing to generate long-term performance data for an integrated system. It has also been used for tests to characterize generator operation while varying control parameters and system inputs, both when controlled with an alternating current (AC) bus and with a digital controller. The ASRG EU currently has over 27,000 hours of operation. This paper summarizes all of the tests that have been conducted on the ASRG EU over the past 3 years and provides an overview of the test results and what was learned.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, N.; Ye, Z.

This report documents part of a multiyear research program dedicated to the development of requirements to support the definition, design, and demonstration of a distributed generation-electric power system interconnection interface concept. The report focuses on the dynamic behavior of power systems when a significant portion of the total energy resource is distributed generation. It also focuses on the near-term reality that the majority of new DG relies on rotating synchronous generators for energy conversion.

Reliability and cost/worth evaluation of generating systems utilizing wind and solar energy

NASA Astrophysics Data System (ADS)

Bagen

The utilization of renewable energy resources such as wind and solar energy for electric power supply has received considerable attention in recent years due to adverse environmental impacts and fuel cost escalation associated with conventional generation. At the present time, wind and/or solar energy sources are utilized to generate electric power in many applications. Wind and solar energy will become important sources for power generation in the future because of their environmental, social and economic benefits, together with public support and government incentives. The wind and sunlight are, however, unstable and variable energy sources, and behave far differently than conventional sources. Energy storage systems are, therefore, often required to smooth the fluctuating nature of the energy conversion system especially in small isolated applications. The research work presented in this thesis is focused on the development and application of reliability and economic benefits assessment associated with incorporating wind energy, solar energy and energy storage in power generating systems. A probabilistic approach using sequential Monte Carlo simulation was employed in this research and a number of analyses were conducted with regards to the adequacy and economic assessment of generation systems containing wind energy, solar energy and energy storage. The evaluation models and techniques incorporate risk index distributions and different operating strategies associated with diesel generation in small isolated systems. Deterministic and probabilistic techniques are combined in this thesis using a system well-being approach to provide useful adequacy indices for small isolated systems that include renewable energy and energy storage. The concepts presented and examples illustrated in this thesis will help power system planners and utility managers to assess the reliability and economic benefits of utilizing wind energy conversion systems, solar energy conversion systems and energy storage in electric power systems and provide useful input to the managerial decision process.

An update of engine system research at the Army Propulsion Directorate

NASA Technical Reports Server (NTRS)

Bobula, George A.

1990-01-01

The Small Turboshaft Engine Research (STER) program provides a vehicle for evaluating the application of emerging technologies to Army turboshaft engine systems and to investigate related phenomena. Capitalizing on the resources at hand, in the form of both the NASA facilities and the Army personnel, the program goal of developing a physical understanding of engine system dynamics and/or system interactions is being realized. STER entries investigate concepts and components developed both in-house and out-of-house. Emphasis is placed upon evaluations which evolved from on-going basic research and advanced development programs. Army aviation program managers are also encouraged to make use of STER resources, both people and facilities. The STER personnel have established their reputations as experts in the fields of engine system experimental evaluations and engine system related phenomena. The STER facility has STER program provides the Army aviation community the opportunity to perform system level investigations, and then to offer the findings to the entire engine community for their consideration in next generation propulsion systems. In this way results of the fundamental research being conducted to meet small turboshaft engine technology challenges expeditiously find their way into that next generation of propulsion systems.

Design factors and considerations for a time-based flight management system

NASA Technical Reports Server (NTRS)

Vicroy, D. D.; Williams, D. H.; Sorensen, J. A.

1986-01-01

Recent NASA Langley Research Center research to develop a technology data base from which an advanced Flight Management System (FMS) design might evolve is reviewed. In particular, the generation of fixed range cruise/descent reference trajectories which meet predefined end conditions of altitude, speed, and time is addressed. Results on the design and theoretical basis of the trajectory generation algorithm are presented, followed by a brief discussion of a series of studies that are being conducted to determine the accuracy requirements of the aircraft and weather models resident in the trajectory generation algorithm. Finally, studies to investigate the interface requirements between the pilot and an advanced FMS are considered.

Automated synthetic scene generation

NASA Astrophysics Data System (ADS)

Givens, Ryan N.

Physics-based simulations generate synthetic imagery to help organizations anticipate system performance of proposed remote sensing systems. However, manually constructing synthetic scenes which are sophisticated enough to capture the complexity of real-world sites can take days to months depending on the size of the site and desired fidelity of the scene. This research, sponsored by the Air Force Research Laboratory's Sensors Directorate, successfully developed an automated approach to fuse high-resolution RGB imagery, lidar data, and hyperspectral imagery and then extract the necessary scene components. The method greatly reduces the time and money required to generate realistic synthetic scenes and developed new approaches to improve material identification using information from all three of the input datasets.

An in-home study of subjective response to simulated sonic booms

NASA Technical Reports Server (NTRS)

Mccurdy, David A.; Brown, Sherilyn A.; Hilliard, R. David

1994-01-01

The proposed development of a second-generation supersonic commercial transport has resulted in increased research efforts to provide an environmentally acceptable aircraft. One of the environmental issues is the impact of sonic booms on people. Aircraft designers are attempting to design the transport to produce sonic boom signatures that will have minimum impact on the public. Current supersonic commercial aircraft produce an 'N-wave' sonic boom pressure signature that is considered unacceptable by the public. This has resulted in first-generation supersonic transports being banned from flying supersonically over land in the United States, a severe economic constraint. By tailoring aircraft volume and lift distributions, designers hope to produce sonic boom signatures having specific shapes other than 'N-wave' that may be more acceptable to the public and could possibly permit overland supersonic flight. As part of the effort to develop a second-generation supersonic commercial transport, Langley Research Center is conducting research to study people's subjective response to sonic booms. As part of that research, a system was developed for performing studies of the subjective response of people to the occurrence of simulated sonic booms in their homes. The In-Home Noise Generation/Response System (IHONORS) provides a degree of situational realism not available in the laboratory and a degree of control over the noise exposure not found in community surveys. The computer-controlled audio system generates the simulated sonic booms, measures the noise levels, and records the subjects' rating and can be placed and operated in individuals' homes for extended periods of time. The system was used to conduct an in-home study of subjective response to simulated sonic booms. The primary objective of the study was to determine the effect on annoyance of the number of sonic boom occurrences in a realistic environment.

Generation of insulin-deficient piglets by disrupting INS gene using CRISPR/Cas9 system.

PubMed

Cho, Bumrae; Kim, Su Jin; Lee, Eun-Jin; Ahn, Sun Mi; Lee, Jin Seok; Ji, Dal-Young; Lee, Kiho; Kang, Jung-Taek

2018-06-01

Diabetes mellitus is a chronic disease with accompanying severe complications. Various animal models, mostly rodents due to availability of genetically modified lines, have been used to investigate the pathophysiology of diabetes. Using pigs for diabetic research can be beneficial because of their similarity in size, pathogenesis pathway, physiology, and metabolism with human. However, the use of pigs for diabetes research has been hampered due to only few pig models presenting diabetes symptoms. In this study, we have successfully generated insulin-deficient pigs by generating the indels of the porcine INS gene in somatic cells using CRISPR/Cas9 system followed by somatic cell nuclear transfer. First, somatic cells carrying a modified INS gene were generated using CRISPR/Cas9 system and their genotypes were confirmed by T7E1 assay; targeting efficiency was 40.4% (21/52). After embryo transfer, three live and five stillborn piglets were born. As expected, INS knockout piglets presented high blood glucose levels and glucose was detected in the urine. The level of insulin and c-peptide in the blood serum of INS knockout piglets were constant after feeding and the expression of insulin in the pancreas was absent in those piglets. This study demonstrates effectiveness of CRISPR/Cas9 system in generating novel pig models. We expect that these insulin-deficient pigs can be used in diabetes research to test the efficacy and safety of new drugs and the recipient of islet transplantation to investigate optimal transplantation strategies.

Networked control of microgrid system of systems

NASA Astrophysics Data System (ADS)

Mahmoud, Magdi S.; Rahman, Mohamed Saif Ur; AL-Sunni, Fouad M.

2016-08-01

The microgrid has made its mark in distributed generation and has attracted widespread research. However, microgrid is a complex system which needs to be viewed from an intelligent system of systems perspective. In this paper, a network control system of systems is designed for the islanded microgrid system consisting of three distributed generation units as three subsystems supplying a load. The controller stabilises the microgrid system in the presence of communication infractions such as packet dropouts and delays. Simulation results are included to elucidate the effectiveness of the proposed control strategy.

GREEN CATALYZED OXIDATION OF HYDROCARBONS IN ALTERNATIVE SOLVENT SYSTEMS GENERATED BY PARIS II DECHEMA; GREEN SOLVENTS FOR CATALYSIS - ENVIRONMENTALLY BENIGN REACTION MEDIA

EPA Science Inventory

Green catalyzed oxidation of hydrocarbons in alternative solvent systems generated by PARIS II
Thomas M. Becker, Michael A. Gonzalez, Paul F. Harten; Sustainable Technology Division, Office of Research and Development; United States Environmental Protection Agency, 26 West Mar...

Validation of Digital Systems in Avionics and Flight Control Applications Handbook. Volume 1.

DTIC Science & Technology

1983-07-01

will also be available to Airways Facilities, Systems Research and Development Service, Air Traffic Control Service, and Flight Standards elements...2114, March 12-14, 1979. 3. Validation Methods Research for Fault-Tolerant Avionics and Control Systems-- *r Working Group Meeting II, NASA...command generation with the multiple methods becoming avail- able for closure of the outer control loop necessitates research on alternative integration

A study using a Monte Carlo method of the optimal configuration of a distribution network in terms of power loss sensing.

PubMed

Moon, Hyun Ho; Lee, Jong Joo; Choi, Sang Yule; Cha, Jae Sang; Kang, Jang Mook; Kim, Jong Tae; Shin, Myong Chul

2011-01-01

Recently there have been many studies of power systems with a focus on "New and Renewable Energy" as part of "New Growth Engine Industry" promoted by the Korean government. "New And Renewable Energy"-especially focused on wind energy, solar energy and fuel cells that will replace conventional fossil fuels-is a part of the Power-IT Sector which is the basis of the SmartGrid. A SmartGrid is a form of highly-efficient intelligent electricity network that allows interactivity (two-way communications) between suppliers and consumers by utilizing information technology in electricity production, transmission, distribution and consumption. The New and Renewable Energy Program has been driven with a goal to develop and spread through intensive studies, by public or private institutions, new and renewable energy which, unlike conventional systems, have been operated through connections with various kinds of distributed power generation systems. Considerable research on smart grids has been pursued in the United States and Europe. In the United States, a variety of research activities on the smart power grid have been conducted within EPRI's IntelliGrid research program. The European Union (EU), which represents Europe's Smart Grid policy, has focused on an expansion of distributed generation (decentralized generation) and power trade between countries with improved environmental protection. Thus, there is current emphasis on a need for studies that assesses the economic efficiency of such distributed generation systems. In this paper, based on the cost of distributed power generation capacity, calculations of the best profits obtainable were made by a Monte Carlo simulation. Monte Carlo simulations that rely on repeated random sampling to compute their results take into account the cost of electricity production, daily loads and the cost of sales and generate a result faster than mathematical computations. In addition, we have suggested the optimal design, which considers the distribution loss associated with power distribution systems focus on sensing aspect and distributed power generation.

Comparison of L-system applications towards plant modelling, music rendering and score generation using visual language programming

NASA Astrophysics Data System (ADS)

Lim, Chen Kim; Tan, Kian Lam; Yusran, Hazwanni; Suppramaniam, Vicknesh

2017-10-01

Visual language or visual representation has been used in the past few years in order to express the knowledge in graphic. One of the important graphical elements is fractal and L-Systems is a mathematic-based grammatical model for modelling cell development and plant topology. From the plant model, L-Systems can be interpreted as music sound and score. In this paper, LSound which is a Visual Language Programming (VLP) framework has been developed to model plant to music sound and generate music score and vice versa. The objectives of this research has three folds: (i) To expand the grammar dictionary of L-Systems music based on visual programming, (ii) To design and produce a user-friendly and icon based visual language framework typically for L-Systems musical score generation which helps the basic learners in musical field and (iii) To generate music score from plant models and vice versa using L-Systems method. This research undergoes a four phases methodology where the plant is first modelled, then the music is interpreted, followed by the output of music sound through MIDI and finally score is generated. LSound is technically compared to other existing applications in the aspects of the capability of modelling the plant, rendering the music and generating the sound. It has been found that LSound is a flexible framework in which the plant can be easily altered through arrow-based programming and the music score can be altered through the music symbols and notes. This work encourages non-experts to understand L-Systems and music hand-in-hand.

The Area IV Soil Conservation Districts Cooperative Research Farm: Thirty years of collaborative research to improve cropping system sustainability in the Northern Plains

USDA-ARS?s Scientific Manuscript database

Findings and interpretations generated from long-term cropping system studies serve to inform the status and trajectory of ecosystem services, while concurrently providing opportunities for further inquiry related to basic/fundamental research. Recent calls for increased investment in long-term cro...

The SWRL Audio Laboratory System (ALS): An Integrated Configuration for Psychomusicology Research. Technical Report 51.

ERIC Educational Resources Information Center

Williams, David Brian; Hoskin, Richard K.

This report describes features of the Audio Laboratory System (ALS), a device which supports research activities of the Southwest Regional Laboratory's Music Program. The ALS is used primarily to generate recorded audio tapes for psychomusicology research related to children's perception and learning of music concepts such as pitch, loudness,…

A Reserve-based Method for Mitigating the Impact of Renewable Energy

NASA Astrophysics Data System (ADS)

Krad, Ibrahim

The fundamental operating paradigm of today's power systems is undergoing a significant shift. This is partially motivated by the increased desire for incorporating variable renewable energy resources into generation portfolios. While these generating technologies offer clean energy at zero marginal cost, i.e. no fuel costs, they also offer unique operating challenges for system operators. Perhaps the biggest operating challenge these resources introduce is accommodating their intermittent fuel source availability. For this reason, these generators increase the system-wide variability and uncertainty. As a result, system operators are revisiting traditional operating strategies to more efficiently incorporate these generation resources to maximize the benefit they provide while minimizing the challenges they introduce. One way system operators have accounted for system variability and uncertainty is through the use of operating reserves. Operating reserves can be simplified as excess capacity kept online during real time operations to help accommodate unforeseen fluctuations in demand. With new generation resources, a new class of operating reserves has emerged that is generally known as flexibility, or ramping, reserves. This new reserve class is meant to better position systems to mitigate severe ramping in the net load profile. The best way to define this new requirement is still under investigation. Typical requirement definitions focus on the additional uncertainty introduced by variable generation and there is room for improvement regarding explicit consideration for the variability they introduce. An exogenous reserve modification method is introduced in this report that can improve system reliability with minimal impacts on total system wide production costs. Another potential solution to this problem is to formulate the problem as a stochastic programming problem. The unit commitment and economic dispatch problems are typically formulated as deterministic problems due to fast solution times and the solutions being sufficient for operations. Improvements in technical computing hardware have reignited interest in stochastic modeling. The variability of wind and solar naturally lends itself to stochastic modeling. The use of explicit reserve requirements in stochastic models is an area of interest for power system researchers. This report introduces a new reserve modification implementation based on previous results to be used in a stochastic modeling framework. With technological improvements in distributed generation technologies, microgrids are currently being researched and implemented. Microgrids are small power systems that have the ability to serve their demand with their own generation resources and may have a connection to a larger power system. As battery technologies improve, they are becoming a more viable option in these distributed power systems and research is necessary to determine the most efficient way to utilize them. This report will investigate several unique operating strategies for batteries in small power systems and analyze their benefits. These new operating strategies will help reduce operating costs and improve system reliability.

Final Report, Next-Generation Mega-Voltage Cargo-Imaging System for Cargo Conainer Inspection, March 2007

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. James Clayton, Ph.D., Varian Medical Systems-Security & Inspection Products; Dr. Emma Regentova, Ph.D, University of Nevada Las Vegas; Dr. Evangelos Yfantis, Ph.D., University of Nevada, Las Vegas

The UNLV Research Foundation, as the primary award recipient, teamed with Varian Medical Systems-Security & Inspection Products and the University of Nevada Las Vegas (UNLV) for the purpose of conducting research and engineering related to a "next-generation" mega-voltage imaging (MVCI) system for inspection of cargo in large containers. The procurement and build-out of hardware for the MVCI project has been completed. The K-9 linear accelerator and an optimized X-ray detection system capable of efficiently detecting X-rays emitted from the accelerator after they have passed through the device is under test. The Office of Science financial assistance award has made possiblemore » the development of a system utilizing a technology which will have a profound positive impact on the security of U.S. seaports. The proposed project will ultimately result in critical research and development advances for the "next-generation" Linatron X-ray accelerator technology, thereby providing a safe, reliable and efficient fixed and mobile cargo inspection system, which will very significantly increase the fraction of cargo containers undergoing reliable inspection as the enter U.S. ports. Both NNSA/NA-22 and the Department of Homeland Security's Domestic Nuclear Detection Office are collaborating with UNLV and its team to make this technology available as soon as possible.« less

NASA Open Rotor Noise Research

NASA Technical Reports Server (NTRS)

Envia, Ed

2010-01-01

Owing to their inherent fuel burn efficiency advantage compared with the current generation high bypass ratio turbofan engines, there is resurgent interest in developing open rotor propulsion systems for powering the next generation commercial aircraft. However, to make open rotor systems truly competitive, they must be made to be acoustically acceptable too. To address this challenge, NASA in collaboration with industry is exploring the design space for low-noise open rotor propulsion systems. The focus is on the system level assessment of the open rotors compared with other candidate concepts like the ultra high bypass ratio cycle engines. To that end there is an extensive research effort at NASA focused on component testing and diagnostics of the open rotor acoustic performance as well as assessment and improvement of open rotor noise prediction tools. In this presentation and overview of the current NASA research on open rotor noise will be provided. Two NASA projects, the Environmentally Responsible Aviation Project and the Subsonic Fixed Wing Project, have been funding this research effort.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zitney, S.E.

Emerging fossil energy power generation systems must operate with unprecedented efficiency and near-zero emissions, while optimizing profitably amid cost fluctuations for raw materials, finished products, and energy. To help address these challenges, the fossil energy industry will have to rely increasingly on the use advanced computational tools for modeling and simulating complex process systems. In this paper, we present the computational research challenges and opportunities for the optimization of fossil energy power generation systems across the plant lifecycle from process synthesis and design to plant operations. We also look beyond the plant gates to discuss research challenges and opportunities formore » enterprise-wide optimization, including planning, scheduling, and supply chain technologies.« less

Human performance cognitive-behavioral modeling: a benefit for occupational safety.

PubMed

Gore, Brian F

2002-01-01

Human Performance Modeling (HPM) is a computer-aided job analysis software methodology used to generate predictions of complex human-automation integration and system flow patterns with the goal of improving operator and system safety. The use of HPM tools has recently been increasing due to reductions in computational cost, augmentations in the tools' fidelity, and usefulness in the generated output. An examination of an Air Man-machine Integration Design and Analysis System (Air MIDAS) model evaluating complex human-automation integration currently underway at NASA Ames Research Center will highlight the importance to occupational safety of considering both cognitive and physical aspects of performance when researching human error.

Human performance cognitive-behavioral modeling: a benefit for occupational safety

NASA Technical Reports Server (NTRS)

Gore, Brian F.

2002-01-01

Human Performance Modeling (HPM) is a computer-aided job analysis software methodology used to generate predictions of complex human-automation integration and system flow patterns with the goal of improving operator and system safety. The use of HPM tools has recently been increasing due to reductions in computational cost, augmentations in the tools' fidelity, and usefulness in the generated output. An examination of an Air Man-machine Integration Design and Analysis System (Air MIDAS) model evaluating complex human-automation integration currently underway at NASA Ames Research Center will highlight the importance to occupational safety of considering both cognitive and physical aspects of performance when researching human error.

Solar Dynamic Power System Stability Analysis and Control

NASA Technical Reports Server (NTRS)

Momoh, James A.; Wang, Yanchun

1996-01-01

The objective of this research is to conduct dynamic analysis, control design, and control performance test of solar power system. Solar power system consists of generation system and distribution network system. A bench mark system is used in this research, which includes a generator with excitation system and governor, an ac/dc converter, six DDCU's and forty-eight loads. A detailed model is used for modeling generator. Excitation system is represented by a third order model. DDCU is represented by a seventh order system. The load is modeled by the combination of constant power and constant impedance. Eigen-analysis and eigen-sensitivity analysis are used for system dynamic analysis. The effects of excitation system, governor, ac/dc converter control, and the type of load on system stability are discussed. In order to improve system transient stability, nonlinear ac/dc converter control is introduced. The direct linearization method is used for control design. The dynamic analysis results show that these controls affect system stability in different ways. The parameter coordination of controllers are recommended based on the dynamic analysis. It is concluded from the present studies that system stability is improved by the coordination of control parameters and the nonlinear ac/dc converter control stabilize system oscillation caused by the load change and system fault efficiently.

A new generation in computing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kahn, R.E.

1983-11-01

Fifth generation of computers is described. The three disciplines involved in bringing such a new generation to reality are: microelectronics; artificial intelligence and, computer systems and architecture. Applications in industry, offices, aerospace, education, health care and retailing are outlined. An analysis is given of research efforts in the US, Japan, U.K., and Europe. Fifth generation programming languages are detailed.

A Low-cost System for Generating Near-realistic Virtual Actors

NASA Astrophysics Data System (ADS)

Afifi, Mahmoud; Hussain, Khaled F.; Ibrahim, Hosny M.; Omar, Nagwa M.

2015-06-01

Generating virtual actors is one of the most challenging fields in computer graphics. The reconstruction of a realistic virtual actor has been paid attention by the academic research and the film industry to generate human-like virtual actors. Many movies were acted by human-like virtual actors, where the audience cannot distinguish between real and virtual actors. The synthesis of realistic virtual actors is considered a complex process. Many techniques are used to generate a realistic virtual actor; however they usually require expensive hardware equipment. In this paper, a low-cost system that generates near-realistic virtual actors is presented. The facial features of the real actor are blended with a virtual head that is attached to the actor's body. Comparing with other techniques that generate virtual actors, the proposed system is considered a low-cost system that requires only one camera that records the scene without using any expensive hardware equipment. The results of our system show that the system generates good near-realistic virtual actors that can be used on many applications.

Final Technical Report for GO15056 Millennium Cell: Development of an Advanced Chemical Hydrogen Storage and Generation System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moreno, Oscar

The objectives of this project are to increase system storage capacity by improving hydrogen generation from concentrated sodium borohydride, with emphasis on reactor and system engineering; to complete a conceptual system design based on sodium borohydride that will include key technology improvements to enable a hydrogen fuel system that will meet the systembased storage capacity of 1.2 kWh/L (36 g H2/L) and 1.5 kWh/kg (45 g H2/kg), by the end of FY 2007; and to utilize engineering expertise to guide Center research in both off-board chemical hydride regeneration and on-board hydrogen generation systems.

Laser-powered MHD generators for space application

NASA Technical Reports Server (NTRS)

Jalufka, N. W.

1986-01-01

Magnetohydrodynamic (MHD) energy conversion systems of the pulsed laser-supported detonation (LSD) wave, plasma MHD, and liquid-metal MHD (LMMHD) types are assessed for their potential as space-based laser-to-electrical power converters. These systems offer several advantages as energy converters relative to the present chemical, nuclear, and solar devices, including high conversion efficiency, simple design, high-temperature operation, high power density, and high reliability. Of these systems, the Brayton cycle liquid-metal MHD system appears to be the most attractive. The LMMHD technology base is well established for terrestrial applications, particularly with regard to the generator, mixer, and other system components. However, further research is required to extend this technology base to space applications and to establish the technology required to couple the laser energy into the system most efficiently. Continued research on each of the three system types is recommended.

Situational Analysis for Complex Systems: Methodological Development in Public Health Research.

PubMed

Martin, Wanda; Pauly, Bernie; MacDonald, Marjorie

2016-01-01

Public health systems have suffered infrastructure losses worldwide. Strengthening public health systems requires not only good policies and programs, but also development of new research methodologies to support public health systems renewal. Our research team considers public health systems to be complex adaptive systems and as such new methods are necessary to generate knowledge about the process of implementing public health programs and services. Within our program of research, we have employed situational analysis as a method for studying complex adaptive systems in four distinct research studies on public health program implementation. The purpose of this paper is to demonstrate the use of situational analysis as a method for studying complex systems and highlight the need for further methodological development.

Applications of Payload Directed Flight

NASA Technical Reports Server (NTRS)

Ippolito, Corey; Fladeland, Matthew M.; Yeh, Yoo Hsiu

2009-01-01

Next generation aviation flight control concepts require autonomous and intelligent control system architectures that close control loops directly around payload sensors in manner more integrated and cohesive that in traditional autopilot designs. Research into payload directed flight control at NASA Ames Research Center is investigating new and novel architectures that can satisfy the requirements for next generation control and automation concepts for aviation. Tighter integration between sensor and machine requires definition of specific sensor-directed control modes to tie the sensor data directly into a vehicle control structures throughout the entire control architecture, from low-level stability- and control loops, to higher level mission planning and scheduling reasoning systems. Payload directed flight systems can thus provide guidance, navigation, and control for vehicle platforms hosting a suite of onboard payload sensors. This paper outlines related research into the field of payload directed flight; and outlines requirements and operating concepts for payload directed flight systems based on identified needs from the scientific literature.'

NASA Hypersonics Overview

NASA Technical Reports Server (NTRS)

Dryer, Jay

2017-01-01

This briefing is an overview of NASA's hypersonic portfolio and core capabilities. The scope of work is fundamental research spanning technology readiness and system complexity levels; critical technologies enabling re-usable hypersonic systems; system-level research, design, analysis, validation; and, engage, invigorate and train the next generation of engineers. This briefing was requested by the Aeronautics Subcommittee of the NASA Advisory Council.

European scientific notes. Volume 38. Number 1. Monthly publication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shaffer, L.E.

1984-01-01

Topics include: Gender-mixed Crews on Dutch Combat Ships; Max-Planck-Institute for Psycholinguistics; Cancer Therapy with Magnetism; 9th European Underwater Biomedical Society Convention; International Center for Genetic Engineering and Biotechnology; Biotechnological Route to Polyphenylene; 2nd Romania-US Seminar on Polymer Chemistry; Statistical Climatology; A Code for Generating Dynamic Models of Robots; Fifth Generation Computing Systems; New Data Logger; Erosion by Liquid and Solid Impact, ELSI VI; Physical Chemistry of the Solid State -- Metals and alloys; NATO Buys a New Oceanographic Research Vessel; Oceanexpo/Oceantropigues 1984; Progress in Development of Wave Energy to Generate Electricity; IAPSO Symposia and Oceanography at the 18th IUGG; Newmore » Decision Support System; High Energy Channeling Research in Switzerland; Muon-Catalyzed Fusion; 2nd International Symposium on Acoustic Remote Sensing of the Atmosphere and Ocean; and Support of Science Research by the British Military.« less

Smart Aquarium as Physics Learning Media for Renewable Energy

NASA Astrophysics Data System (ADS)

Desnita, D.; Raihanati, R.; Susanti, D.

2018-04-01

Smart aquarium has been developed as a learning media to visualize Micro Hydro Power Generator (MHPG). Its used aquarium water circulation system and Wind Power Generation (WPG) which generated through a wheel as a source. Its also used to teach about energy changes, circular motion and wheel connection, electromagnetic impact, and AC power circuit. The output power and system efficiency was adjusted through the adjustment of water level and wind speed. Specific targets in this research are: to achieved: (i) develop green aquarium technology that’s suitable to used as a medium of physics learning, (ii) improving quality of process and learning result at a senior high school student. Research method used development research by Borg and Gall, which includes preliminary studies, design, product development, expert validation, and product feasibility test, and vinalisation. The validation test by the expert states that props feasible to use. Limited trials conducted prove that this tool can improve students science process skills.

Summary of NASA-Lewis Research Center solar heating and cooling and wind energy programs

NASA Technical Reports Server (NTRS)

Vernon, R. W.

1975-01-01

NASA is planning to construct and operate a solar heating and cooling system in conjunction with a new office building being constructed at Langley Research Center. The technology support for this project will be provided by a solar energy program underway at NASA's Lewis Research Center. The solar program at Lewis includes: testing of solar collectors with a solar simulator, outdoor testing of collectors, property measurements of selective and nonselective coatings for solar collectors, and a solar model-systems test loop. NASA-Lewis has been assisting the National Science Foundation and now the Energy Research and Development Administration in planning and executing a national wind energy program. The areas of the wind energy program that are being conducted by Lewis include: design and operation of a 100 kW experimental wind generator, industry-designed and user-operated wind generators in the range of 50 to 3000 kW, and supporting research and technology for large wind energy systems. An overview of these activities is provided.

MAPGEN CARTOGRAPHIC SYSTEM.

USGS Publications Warehouse

Evenden, Gerald I.; ,

1986-01-01

MAPGEN is a software system that facilitates production of cartographic displays in the research and production environment. The system generates a set of metagraphic overlays of application-defined geographical information that can be aggregated in any combination for display without reprocessing the original data. An overview of the control files, available cartographic projections, graphic attributes, overlay generator and ancillary support programs, and the device-independent graphic subsystem are presented, along with examples of usage. System transportability and associated host hardware and operating system requirements are also addressed.

Acquisition, representation and rule generation for procedural knowledge

NASA Technical Reports Server (NTRS)

Ortiz, Chris; Saito, Tim; Mithal, Sachin; Loftin, R. Bowen

1991-01-01

Current research into the design and continuing development of a system for the acquisition of procedural knowledge, its representation in useful forms, and proposed methods for automated C Language Integrated Production System (CLIPS) rule generation is discussed. The Task Analysis and Rule Generation Tool (TARGET) is intended to permit experts, individually or collectively, to visually describe and refine procedural tasks. The system is designed to represent the acquired knowledge in the form of graphical objects with the capacity for generating production rules in CLIPS. The generated rules can then be integrated into applications such as NASA's Intelligent Computer Aided Training (ICAT) architecture. Also described are proposed methods for use in translating the graphical and intermediate knowledge representations into CLIPS rules.

What Research Says about Unequal Funding for Schools in America. In Pursuit of Better Schools: What Research Says.

ERIC Educational Resources Information Center

Biddle, Bruce J.; Berliner, David C.

Public school funding in America comes from federal, state, and local sources. Because nearly half of those funds are generated by local property taxes, the American system generates large funding differences between wealthy and impoverished communities. This paper reports on the characteristics of these financial inequities. It notes that sharp…

Evaluation of the Pilot Mentoring Program at the Research Foundation for SUNY

ERIC Educational Resources Information Center

Henderson-Harr, Amy; Caggiano-Siino, Kathleen; Prewitt, Ashlee

2016-01-01

This article provides a description of an 18-month pilot program focused on the leadership development of the next generation of research administrators (RAs) in the State University of New York system (SUNY). The key questions for the evaluators were: 1) can we create a developmental program that effectively prepares the next generation of RAs;…

Next-Generation Summative English Language Proficiency Assessments for English Learners: Priorities for Policy and Research. Research Report. ETS RR-16-08

ERIC Educational Resources Information Center

Wolf, Mikyung Kim; Guzman-Orth, Danielle; Hauck, Maurice Cogan

2016-01-01

This paper is the third in a series concerning English language proficiency (ELP) assessments for K-12 English learners (ELs). The series, produced from Educational Testing Service (ETS), is intended to provide theory- and evidence-based principles and recommendations for improving next-generation ELP assessment systems, policies, and practices…

Next Generation Traffic Control Systems Workshop Summary Report

DOT National Transportation Integrated Search

2015-12-01

On February 3-4, 2015, at the Turner-Fairbank Highway Research Center in McLean, Virginia, the Federal Highway Administration's Office of Operations Research and Development, with support from the Exploratory Advanced Research Program, convened the 2...

NASA's Hypersonic Investment Area

NASA Technical Reports Server (NTRS)

Hueter, Uwe; Hutt, John; McClinton, Charles

2002-01-01

NASA has established long term goals for access to space. The third generation launch systems are to be fully reusable and operational around 2025. The goal for third-generation launch systems represents significant reduction in cost and improved safety over the current first generation system. The Advanced Space Transportation Office (ASTP) at NASA s Marshall Space Flight Center (MSFC) has the agency lead to develop space transportation technologies. Within ASTP, under the Hypersonic Investment Area (HIA), third generation technologies are being pursued in the areas of propulsion, airframe, integrated vehicle health management (IVHM), avionics, power, operations and system analysis. These technologies are being matured through research and both ground and flight-testing. This paper provides an overview of the HIA program plans and recent accomplishments.

Research on complex 3D tree modeling based on L-system

NASA Astrophysics Data System (ADS)

Gang, Chen; Bin, Chen; Yuming, Liu; Hui, Li

2018-03-01

L-system as a fractal iterative system could simulate complex geometric patterns. Based on the field observation data of trees and knowledge of forestry experts, this paper extracted modeling constraint rules and obtained an L-system rules set. Using the self-developed L-system modeling software the L-system rule set was parsed to generate complex tree 3d models.The results showed that the geometrical modeling method based on l-system could be used to describe the morphological structure of complex trees and generate 3D tree models.

An Efficient, Rapid, and Recyclable System for CRISPR-Mediated Genome Editing in Candida albicans.

PubMed

Nguyen, Namkha; Quail, Morgan M F; Hernday, Aaron D

2017-01-01

Candida albicans is the most common fungal pathogen of humans. Historically, molecular genetic analysis of this important pathogen has been hampered by the lack of stable plasmids or meiotic cell division, limited selectable markers, and inefficient methods for generating gene knockouts. The recent development of clustered regularly interspaced short palindromic repeat(s) (CRISPR)-based tools for use with C. albicans has opened the door to more efficient genome editing; however, previously reported systems have specific limitations. We report the development of an optimized CRISPR-based genome editing system for use with C. albicans . Our system is highly efficient, does not require molecular cloning, does not leave permanent markers in the genome, and supports rapid, precise genome editing in C. albicans . We also demonstrate the utility of our system for generating two independent homozygous gene knockouts in a single transformation and present a method for generating homozygous wild-type gene addbacks at the native locus. Furthermore, each step of our protocol is compatible with high-throughput strain engineering approaches, thus opening the door to the generation of a complete C. albicans gene knockout library. IMPORTANCE Candida albicans is the major fungal pathogen of humans and is the subject of intense biomedical and discovery research. Until recently, the pace of research in this field has been hampered by the lack of efficient methods for genome editing. We report the development of a highly efficient and flexible genome editing system for use with C. albicans . This system improves upon previously published C. albicans CRISPR systems and enables rapid, precise genome editing without the use of permanent markers. This new tool kit promises to expedite the pace of research on this important fungal pathogen.

Networking and Information Technology Research and Development. Supplement to the President’s Budget for FY 2002

DTIC Science & Technology

2001-07-01

Web-based applications to improve health data systems and quality of care; innovative strategies for data collection in clinical settings; approaches...research to increase interoperability and integration of software in distributed systems ; protocols and tools for data annotation and management; and...Generation National Defense and National Security Systems .......................... 27 Improved Health Care Systems for All Citizens

Digitizing for Computer-Aided Finite Element Model Generation.

DTIC Science & Technology

1979-10-10

this approach is a collection of programs developed over the last eight years at the University of Arizona, and called the GIFTS system. This paper...briefly describes the latest version of the system, GIFTS -5, and demonstrates its suitability in a design environment by simple examples. The programs...constituting the GIFTS system were used as a tool for research in many areas, including mesh generation, finite element data base design, interactive

Using Wikipedia and Conceptual Graph Structures to Generate Questions for Academic Writing Support

ERIC Educational Resources Information Center

Liu, Ming; Calvo, R. A.; Aditomo, A.; Pizzato, L. A.

2012-01-01

In this paper, we present a novel approach for semiautomatic question generation to support academic writing. Our system first extracts key phrases from students' literature review papers. Each key phrase is matched with a Wikipedia article and classified into one of five abstract concept categories: Research Field, Technology, System, Term, and…

Conceptualizing Accessibility for English Language Proficiency Assessments. Research Report. ETS RR-16-07

ERIC Educational Resources Information Center

Guzman-Orth, Danielle; Laitusis, Cara; Thurlow, Martha; Christensen, Laurene

2016-01-01

This paper is the second in a series from Educational Testing Service (ETS) that conceptualizes next-generation English language proficiency (ELP) assessment systems for K-12 English learners (ELs) in the United States.The first paper articulated a high-level conceptualization of next-generation ELP assessment systems (Hauck, Wolf, & Mislevy,…

Comparative Efficacy of the Picture Exchange Communication System (PECS) versus a Speech-Generating Device: Effects on Requesting Skills

ERIC Educational Resources Information Center

Boesch, Miriam C.; Wendt, Oliver; Subramanian, Anu; Hsu, Ning

2013-01-01

An experimental, single-subject research study investigated the comparative efficacy of the Picture Exchange Communication System (PECS) versus a speech-generating device (SGD) in developing requesting skills for three elementary-age children with severe autism and little to no functional speech. Results demonstrated increases in requesting…

Vascular Dysfunction in Mother and Offspring During Preeclampsia: Contributions from Latin-American Countries.

PubMed

Giachini, Fernanda Regina; Galaviz-Hernandez, Carlos; Damiano, Alicia E; Viana, Marta; Cadavid, Angela; Asturizaga, Patricia; Teran, Enrique; Clapes, Sonia; Alcala, Martin; Bueno, Julio; Calderón-Domínguez, María; Ramos, María P; Lima, Victor Vitorino; Sosa-Macias, Martha; Martinez, Nora; Roberts, James M; Escudero, Carlos

2017-10-06

Pregnancy is a physiologically stressful condition that generates a series of functional adaptations by the cardiovascular system. The impact of pregnancy on this system persists from conception beyond birth. Recent evidence suggests that vascular changes associated with pregnancy complications, such as preeclampsia, affect the function of the maternal and offspring vascular systems, after delivery and into adult life. Since the vascular system contributes to systemic homeostasis, defective development or function of blood vessels predisposes both mother and infant to future risk for chronic disease. These alterations in later life range from fertility problems to alterations in the central nervous system or immune system, among others. It is important to note that rates of morbi-mortality due to pregnancy complications including preeclampsia, as well as cardiovascular diseases, have a higher incidence in Latin-American countries than in more developed countries. Nonetheless, there is a lack both in the amount and impact of research conducted in Latin America. An impact, although smaller, can be seen when research in vascular disorders related to problems during pregnancy is analyzed. Therefore, in this review, information about preeclampsia and endothelial dysfunction generated from research groups based in Latin-American countries will be highlighted. We relate the need, as present in many other countries in the world, for increased effective regional and international collaboration to generate new data specific to our region on this topic.

Dynamic analysis of combined photovoltaic source and synchronous generator connected to power grid

NASA Astrophysics Data System (ADS)

Mahabal, Divya

In the world of expanding economy and technology, the energy demand is likely to increase even with the global efforts of saving and increasing energy efficiency. Higher oil prices, effects of greenhouse gases, and concerns over other environmental impacts gave way to Distributed Generation (DG). With adequate awareness and support, DG's can meet these rising energy demands at lower prices compared to conventional methods. Extensive research is taking place in different areas like fuel cells, photovoltaic cells, wind turbines, and gas turbines. DG's when connected to a grid increase the overall efficiency of the power grid. It is believed that three-fifth of the world's electricity would account for renewable energy by middle of 21st century. This thesis presents the dynamic analysis of a grid connected photovoltaic (PV) system and synchronous generator. A grid is considered as an infinite bus. The photovol-taic system and synchronous generator act as small scale distributed energy resources. The output of the photovoltaic system depends on the light intensity, temperature, and irradiance levels of sun. The maximum power point tracking and DC/AC converter are also modeled for the photovoltaic system. The PV system is connected to the grid through DC/AC system. Different combinations of PV and synchronous generator are modeled with the grid to study the dynamics of the proposed system. The dynamics of the test system is analyzed by subjecting the system to several disturbances under various conditions. All modules are individually modeled and con-nected using MATLAB/Simulink software package. Results from the study show that, as the penetration of renewable energy sources like PV increases into the power system, the dynamics of the system becomes faster. When considering cases such as load switching, PV cannot deliver more power as the performance of PV depends on environmental conditions. Synchronous generator in power system can produce the required amount of power. As the main aim of this research is to use renewable sources like PV in the system, it is advantageous to use a combination of both PV and synchronous generator in the system.

A Rapid Prototyping Look at NASA's Next Generation Earth-Observing Satellites; Opportunities for Global Change Research and Applications

NASA Astrophysics Data System (ADS)

Cecil, L.; Young, D. F.; Parker, P. A.; Eckman, R. S.

2006-12-01

The NASA Applied Sciences Program extends the results of Earth Science Division (ESD) research and knowledge beyond the scientific and research communities to contribute to national priority applications with societal benefits. The Applied Sciences Program focuses on, (1) assimilation of NASA Earth-science research results and their associated uncertainties to improve decision support systems and, (2) the transition of NASA research results to evolve improvements in future operational systems. The broad range of Earth- science research results that serve as inputs to the Applied Sciences Program are from NASA's Research and Analysis Program (R&A) within the ESD. The R&A Program has established six research focus areas to study the complex processes associated with Earth-system science; Atmospheric Composition, Carbon Cycle and Ecosystems, Climate Variability and Change, Earth Surface and Interior, Water and Energy Cycle, and Weather. Through observations-based Earth-science research results, NASA and its partners are establishing predictive capabilities for future projections of natural and human perturbations on the planet. The focus of this presentation is on the use of research results and their associated uncertainties from several of NASA's nine next generation missions for societal benefit. The newly launched missions are, (1) CloudSat, and (2) CALIPSO (Cloud Aerosol Lidar and Infrared Pathfinder Satellite Observations), both launched April 28, 2006, and the planned next generation missions include, (3) the Orbiting Carbon Observatory (OCO), (4) the Global Precipitation Mission (GPM), (5) the Landsat Data Continuity Mission (LDCM), (6) Glory, for measuring the spatial and temporal distribution of aerosols and total solar irradiance for long-term climate records, (7) Aquarius, for measuring global sea surface salinity, (8) the Ocean Surface Topography Mission (OSTM), and (9) the NPOESS Preparatory Project (NPP) for measuring long-term climate trends and global biological productivity. NASA's Applied Sciences Program is taking a scientifically rigorous systems engineering approach to facilitate rapid prototyping of potential uses of the projected research capabilities of these new missions into decision support systems. This presentation includes an example of a prototype experiment that focuses on two of the Applied Sciences Program's twelve National Applications focus areas, Water Management and Energy Management. This experiment is utilizing research results and associated uncertainties from existing Earth-observation missions as well as from several of NASA's nine next generation missions. This prototype experiment is simulating decision support analysis and research results leading to priority management and/or policy issues concentrating on climate change and uncertainties in alpine areas on the watershed scale.

Integrated voice and visual systems research topics

NASA Technical Reports Server (NTRS)

Williams, Douglas H.; Simpson, Carol A.

1986-01-01

A series of studies was performed to investigate factors of helicopter speech and visual system design and measure the effects of these factors on human performance, both for pilots and non-pilots. The findings and conclusions of these studies were applied by the U.S. Army to the design of the Army's next generation threat warning system for helicopters and to the linguistic functional requirements for a joint Army/NASA flightworthy, experimental speech generation and recognition system.

Moving to the Next Generation System Design: Integrating Cognition, Assessment, and Learning. CSE Report 706

ERIC Educational Resources Information Center

Baker, Eva L.

2007-01-01

This paper will describe the relationships between research on learning and its application in assessment models and operational systems. These have been topics of research at the National Center for Research on Evaluation, Standards, and Student Testing (CRESST) for more than 20 years and form a significant part of the intellectual foundation of…

Analysis of Factors Enhancing Pitfall in Research and Teaching of the Nigerian University System

ERIC Educational Resources Information Center

Ahmed, Tafida; Umar, Kasim; Paul, Chima

2015-01-01

The paper analyses factors enhancing pitfall in research and teaching in the Nigerian university system. Using data generated from secondary sources, it was found that so many factors are responsible for the constant decay in teaching and research in the Nigerian universities. The paper however found from literature that the high rate of pitfalls…

Identification and Characterization of Key Human Performance Issues and Research in the Next Generation Air Transportation System (NextGen)

NASA Technical Reports Server (NTRS)

Lee, Paul U.; Sheridan, Tom; Poage, james L.; Martin, Lynne Hazel; Jobe, Kimberly K.

2010-01-01

This report identifies key human-performance-related issues associated with Next Generation Air Transportation System (NextGen) research in the NASA NextGen-Airspace Project. Four Research Focus Areas (RFAs) in the NextGen-Airspace Project - namely Separation Assurance (SA), Airspace Super Density Operations (ASDO), Traffic Flow Management (TFM), and Dynamic Airspace Configuration (DAC) - were examined closely. In the course of the research, it was determined that the identified human performance issues needed to be analyzed in the context of NextGen operations rather than through basic human factors research. The main gaps in human factors research in NextGen were found in the need for accurate identification of key human-systems related issues within the context of specific NextGen concepts and better design of the operational requirements for those concepts. By focusing on human-system related issues for individual concepts, key human performance issues for the four RFAs were identified and described in this report. In addition, mixed equipage airspace with components of two RFAs were characterized to illustrate potential human performance issues that arise from the integration of multiple concepts.

An advanced programmable/reconfigurable color graphics display system for crew station technology research

NASA Technical Reports Server (NTRS)

Montoya, R. J.; England, J. N.; Hatfield, J. J.; Rajala, S. A.

1981-01-01

The hardware configuration, software organization, and applications software for the NASA IKONAS color graphics display system are described. The systems were created at the Langley Research Center Display Device Laboratory to develop, evaluate, and demonstrate advanced generic concepts, technology, and systems integration techniques for electronic crew station systems of future civil aircraft. A minicomputer with 64K core memory acts as a host for a raster scan graphics display generator. The architectures of the hardware system and the graphics display system are provided. The applications software features a FORTRAN-based model of an aircraft, a display system, and the utility program for real-time communications. The model accepts inputs from a two-dimensional joystick and outputs a set of aircraft states. Ongoing and planned work for image segmentation/generation, specialized graphics procedures, and higher level language user interface are discussed.

Vision for a Global Registry of Anticipated Public Health Studies

PubMed Central

Choi, Bernard C.K.; Frank, John; Mindell, Jennifer S.; Orlova, Anna; Lin, Vivian; Vaillancourt, Alain D.M.G.; Puska, Pekka; Pang, Tikki; Skinner, Harvey A.; Marsh, Marsha; Mokdad, Ali H.; Yu, Shun-Zhang; Lindner, M. Cristina; Sherman, Gregory; Barreto, Sandhi M.; Green, Lawrence W.; Svenson, Lawrence W.; Sainsbury, Peter; Yan, Yongping; Zhang, Zuo-Feng; Zevallos, Juan C.; Ho, Suzanne C.; de Salazar, Ligia M.

2007-01-01

In public health, the generation, management, and transfer of knowledge all need major improvement. Problems in generating knowledge include an imbalance in research funding, publication bias, unnecessary studies, adherence to fashion, and undue interest in novel and immediate issues. Impaired generation of knowledge, combined with a dated and inadequate process for managing knowledge and an inefficient system for transferring knowledge, mean a distorted body of evidence available for decisionmaking in public health. This article hopes to stimulate discussion by proposing a Global Registry of Anticipated Public Health Studies. This prospective, comprehensive system for tracking research in public health could help enhance collaboration and improve efficiency. Practical problems must be discussed before such a vision can be further developed. PMID:17413073

Architectures Toward Reusable Science Data Systems

NASA Technical Reports Server (NTRS)

Moses, John Firor

2014-01-01

Science Data Systems (SDS) comprise an important class of data processing systems that support product generation from remote sensors and in-situ observations. These systems enable research into new science data products, replication of experiments and verification of results. NASA has been building systems for satellite data processing since the first Earth observing satellites launched and is continuing development of systems to support NASA science research and NOAA's Earth observing satellite operations. The basic data processing workflows and scenarios continue to be valid for remote sensor observations research as well as for the complex multi-instrument operational satellite data systems being built today.

Public health systems research: the state of the field.

PubMed

Bagley, Prue; Lin, Vivian

2008-11-01

Public health infrastructure provides the building blocks required for the system to achieve public health goals. A systems approach to public health has been suggested as a means to tackle persistent and emerging problems. Systems and infrastructure are attracting increased research attention. A review of the Australian and international literature suggests an absence of empirical evidence about how the system and its component parts does, or should, work and highlights some of the difficulties associated with generating such evidence. It also indicates there is significant scope for further research.

Applications of Panoramic Images: from 720° Panorama to Interior 3d Models of Augmented Reality

NASA Astrophysics Data System (ADS)

Lee, I.-C.; Tsai, F.

2015-05-01

A series of panoramic images are usually used to generate a 720° panorama image. Although panoramic images are typically used for establishing tour guiding systems, in this research, we demonstrate the potential of using panoramic images acquired from multiple sites to create not only 720° panorama, but also three-dimensional (3D) point clouds and 3D indoor models. Since 3D modeling is one of the goals of this research, the location of the panoramic sites needed to be carefully planned in order to maintain a robust result for close-range photogrammetry. After the images are acquired, panoramic images are processed into 720° panoramas, and these panoramas which can be used directly as panorama guiding systems or other applications. In addition to these straightforward applications, interior orientation parameters can also be estimated while generating 720° panorama. These parameters are focal length, principle point, and lens radial distortion. The panoramic images can then be processed with closerange photogrammetry procedures to extract the exterior orientation parameters and generate 3D point clouds. In this research, VisaulSFM, a structure from motion software is used to estimate the exterior orientation, and CMVS toolkit is used to generate 3D point clouds. Next, the 3D point clouds are used as references to create building interior models. In this research, Trimble Sketchup was used to build the model, and the 3D point cloud was added to the determining of locations of building objects using plane finding procedure. In the texturing process, the panorama images are used as the data source for creating model textures. This 3D indoor model was used as an Augmented Reality model replacing a guide map or a floor plan commonly used in an on-line touring guide system. The 3D indoor model generating procedure has been utilized in two research projects: a cultural heritage site at Kinmen, and Taipei Main Station pedestrian zone guidance and navigation system. The results presented in this paper demonstrate the potential of using panoramic images to generate 3D point clouds and 3D models. However, it is currently a manual and labor-intensive process. A research is being carried out to Increase the degree of automation of these procedures.

Reconstructing a Large-Scale Population for Social Simulation

NASA Astrophysics Data System (ADS)

Fan, Zongchen; Meng, Rongqing; Ge, Yuanzheng; Qiu, Xiaogang

The advent of social simulation has provided an opportunity to research on social systems. More and more researchers tend to describe the components of social systems in a more detailed level. Any simulation needs the support of population data to initialize and implement the simulation systems. However, it's impossible to get the data which provide full information about individuals and households. We propose a two-step method to reconstruct a large-scale population for a Chinese city according to Chinese culture. Firstly, a baseline population is generated through gathering individuals into households one by one; secondly, social relationships such as friendship are assigned to the baseline population. Through a case study, a population of 3,112,559 individuals gathered in 1,133,835 households is reconstructed for Urumqi city, and the results show that the generated data can respect the real data quite well. The generated data can be applied to support modeling of some social phenomenon.

Advanced Stirling Technology Development at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Shaltens, Richard K.; Wong, Wayne A.

2007-01-01

The NASA Glenn Research Center has been developing advanced energy-conversion technologies for use with both radioisotope power systems and fission surface power systems for many decades. Under NASA's Science Mission Directorate, Planetary Science Theme, Technology Program, Glenn is developing the next generation of advanced Stirling convertors (ASCs) for use in the Department of Energy/Lockheed Martin Advanced Stirling Radioisotope Generator (ASRG). The next-generation power-conversion technologies require high efficiency and high specific power (watts electric per kilogram) to meet future mission requirements to use less of the Department of Energy's plutonium-fueled general-purpose heat source modules and reduce system mass. Important goals include long-life (greater than 14-yr) reliability and scalability so that these systems can be considered for a variety of future applications and missions including outer-planet missions and continual operation on the surface of Mars. This paper provides an update of the history and status of the ASC being developed for Glenn by Sunpower Inc. of Athens, Ohio.

Cognitive Systems Modeling and Analysis of Command and Control Systems

NASA Technical Reports Server (NTRS)

Norlander, Arne

2012-01-01

Military operations, counter-terrorism operations and emergency response often oblige operators and commanders to operate within distributed organizations and systems for safe and effective mission accomplishment. Tactical commanders and operators frequently encounter violent threats and critical demands on cognitive capacity and reaction time. In the future they will make decisions in situations where operational and system characteristics are highly dynamic and non-linear, i.e. minor events, decisions or actions may have serious and irreversible consequences for the entire mission. Commanders and other decision makers must manage true real time properties at all levels; individual operators, stand-alone technical systems, higher-order integrated human-machine systems and joint operations forces alike. Coping with these conditions in performance assessment, system development and operational testing is a challenge for both practitioners and researchers. This paper reports on research from which the results led to a breakthrough: An integrated approach to information-centered systems analysis to support future command and control systems research development. This approach integrates several areas of research into a coherent framework, Action Control Theory (ACT). It comprises measurement techniques and methodological advances that facilitate a more accurate and deeper understanding of the operational environment, its agents, actors and effectors, generating new and updated models. This in turn generates theoretical advances. Some good examples of successful approaches are found in the research areas of cognitive systems engineering, systems theory, and psychophysiology, and in the fields of dynamic, distributed decision making and naturalistic decision making.

An university-scale pulsed-power system using a bipolar Marx generator

NASA Astrophysics Data System (ADS)

Chang, Po-Yu; Yang, Sheng-Hua; Huang, Mei-Feng; Isaps, Natl Cheng Kung Univ Team

2017-10-01

A bipolar Marx generator is being built for x-ray sources or laboratory astrophysics and space research for university-scale laboratory. The system consists of ten stages. In each stage, two 1 μF capacitors connected in series are charged to +/- 30 kV storing 9 kJ of total energy. It delivers a current of 200 kA to the load with a 200 ns rise time during the discharge. It will be used for following three purposes: (1) gas-puff z pinches generating soft x-ray for bio-medical research in the future; (2) generating plasma jets to study interactions between plasma flows and unmagnetized/magnetized obstacles analogous to the interactions between solar winds and planetary magnetic fields or unmagnetized planets; and (3) studying the pinch in a dense plasma focus device. The results of current measurements and circuit characteristics are shown.

Power in the loop real time simulation platform for renewable energy generation

NASA Astrophysics Data System (ADS)

Li, Yang; Shi, Wenhui; Zhang, Xing; He, Guoqing

2018-02-01

Nowadays, a large scale of renewable energy sources has been connecting to power system and the real time simulation platform is widely used to carry out research on integration control algorithm, power system stability etc. Compared to traditional pure digital simulation and hardware in the loop simulation, power in the loop simulation has higher accuracy and degree of reliability. In this paper, a power in the loop analog digital hybrid simulation platform has been built and it can be used not only for the single generation unit connecting to grid, but also for multiple new energy generation units connecting to grid. A wind generator inertia control experiment was carried out on the platform. The structure of the inertia control platform was researched and the results verify that the platform is up to need for renewable power in the loop real time simulation.

Refractory Research Group - U.S. DOE, Albany Research Center [Institution Profile

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bennett, James P.

2004-09-01

The refractory research group at the Albany Research Center (ARC) has a long history of conducting materials research within the U.S. Bureau of Mines, and more recently, within the U.S. Dept. of Energy. When under the U.S. Bureau of Mines, research was driven by national needs to develop substitute materials and to conserve raw materials. This mission was accomplished by improving refractory material properties and/or by recycling refractories using critical and strategic materials. Currently, as a U.S. Dept of Energy Fossil Energy field site, research is driven primarily by the need to assist DOE in meeting its vision to developmore » economically and environmentally viable technologies for the production of electricity from fossil fuels. Research at ARC impacts this vision by: • Providing information on the performance characteristics of materials being specified for the current generation of power systems; • Developing cost-effective, high performance materials for inclusion in the next generation of fossil power systems; and • Solving environmental emission and waste problems related to fossil energy systems. A brief history of past refractory research within the U.S. Bureau of Mines, the current refractory research at ARC, and the equipment and capabilities used to conduct refractory research at ARC will be discussed.« less

Systematic Approach to Better Understanding Integration Costs: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stark, Gregory B.

2015-09-28

When someone mentions integration costs, thoughts of the costs of integrating renewable generation into an existing system come to mind. We think about how variability and uncertainty can increase power system cycling costs as increasing amounts of wind or solar generation are incorporated into the generation mix. However, seldom do we think about what happens to system costs when new baseload generation is added to an existing system or when generation self-schedules. What happens when a highly flexible combined-cycle plant is added? Do system costs go up, or do they go down? Are other, non-cycling, maintenance costs impacted? In thismore » paper we investigate six technologies and operating practices--including VG, baseload generation, generation mix, gas prices, self-scheduling, and fast-start generation--and how changes in these areas can impact a system's operating costs. This paper provides a working definition of integration costs and four components of variable costs. It describes the study approach and how a production cost modeling-based method was used to determine the cost effects, and, as a part of the study approach section, it describes the test system and data used for the comparisons. Finally, it presents the research findings, and, in closing, suggests three areas for future work.« less

Maximum wind energy extraction strategies using power electronic converters

NASA Astrophysics Data System (ADS)

Wang, Quincy Qing

2003-10-01

This thesis focuses on maximum wind energy extraction strategies for achieving the highest energy output of variable speed wind turbine power generation systems. Power electronic converters and controls provide the basic platform to accomplish the research of this thesis in both hardware and software aspects. In order to send wind energy to a utility grid, a variable speed wind turbine requires a power electronic converter to convert a variable voltage variable frequency source into a fixed voltage fixed frequency supply. Generic single-phase and three-phase converter topologies, converter control methods for wind power generation, as well as the developed direct drive generator, are introduced in the thesis for establishing variable-speed wind energy conversion systems. Variable speed wind power generation system modeling and simulation are essential methods both for understanding the system behavior and for developing advanced system control strategies. Wind generation system components, including wind turbine, 1-phase IGBT inverter, 3-phase IGBT inverter, synchronous generator, and rectifier, are modeled in this thesis using MATLAB/SIMULINK. The simulation results have been verified by a commercial simulation software package, PSIM, and confirmed by field test results. Since the dynamic time constants for these individual models are much different, a creative approach has also been developed in this thesis to combine these models for entire wind power generation system simulation. An advanced maximum wind energy extraction strategy relies not only on proper system hardware design, but also on sophisticated software control algorithms. Based on literature review and computer simulation on wind turbine control algorithms, an intelligent maximum wind energy extraction control algorithm is proposed in this thesis. This algorithm has a unique on-line adaptation and optimization capability, which is able to achieve maximum wind energy conversion efficiency through continuously improving the performance of wind power generation systems. This algorithm is independent of wind power generation system characteristics, and does not need wind speed and turbine speed measurements. Therefore, it can be easily implemented into various wind energy generation systems with different turbine inertia and diverse system hardware environments. In addition to the detailed description of the proposed algorithm, computer simulation results are presented in the thesis to demonstrate the advantage of this algorithm. As a final confirmation of the algorithm feasibility, the algorithm has been implemented inside a single-phase IGBT inverter, and tested with a wind simulator system in research laboratory. Test results were found consistent with the simulation results. (Abstract shortened by UMI.)

An Intelligent CAI Monitor and Generative Tutor. Final Report.

ERIC Educational Resources Information Center

Koffman, Elliot B.; Perry, James

This final report summarizes research findings and presents a model for generative computer assisted instruction (CAI) with respect to its usefulness in the classroom environment. Methods used to individualize instruction, and the evolution of a procedure used to select a concept for presentation to a student with the generative CAI system are…

Systems Based Approaches for Thermochemical Conversion of Biomass to Bioenergy and Bioproducts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, Steven

2016-07-11

Auburn’s Center for Bioenergy and Bioproducts conducts research on production of synthesis gas for use in power generation and the production of liquid fuels. The overall goal of our gasification research is to identify optimal processes for producing clean syngas to use in production of fuels and chemicals from underutilized agricultural and forest biomass feedstocks. This project focused on construction and commissioning of a bubbling-bed fluidized-bed gasifier and subsequent shakedown of the gasification and gas cleanup system. The result of this project is a fully commissioned gasification laboratory that is conducting testing on agricultural and forest biomass. Initial tests onmore » forest biomass have served as the foundation for follow-up studies on gasification under a more extensive range of temperatures, pressures, and oxidant conditions. The laboratory gasification system consists of a biomass storage tank capable of holding up to 6 tons of biomass; a biomass feeding system, with loss-in-weight metering system, capable of feeding biomass at pressures up to 650 psig; a bubbling-bed fluidized-bed gasification reactor capable of operating at pressures up to 650 psig and temperatures of 1500oF with biomass flowrates of 80 lb/hr and syngas production rates of 37 scfm; a warm-gas filtration system; fixed bed reactors for gas conditioning; and a final quench cooling system and activated carbon filtration system for gas conditioning prior to routing to Fischer-Tropsch reactors, or storage, or venting. This completed laboratory enables research to help develop economically feasible technologies for production of biomass-derived synthesis gases that will be used for clean, renewable power generation and for production of liquid transportation fuels. Moreover, this research program provides the infrastructure to educate the next generation of engineers and scientists needed to implement these technologies.« less

Assessing the value of patient-generated data to comparative effectiveness research.

PubMed

Howie, Lynn; Hirsch, Bradford; Locklear, Tracie; Abernethy, Amy P

2014-07-01

The goal of comparative effectiveness research is to assess medical therapies and allow patients, health care providers, payers, and policy makers to make evidence-based decisions about the most appropriate therapies in routine clinical practice. To conduct this type of research and to inform health care delivery, data about the impact of interventions on patient outcomes are needed. Methods of generating evidence for comparative effectiveness research provide opportunities to engage patients and understand their experiences with illness and its treatment. In this article we assess the need for, uses of, and strengths and weaknesses of patient-generated data. We also review in brief federal and medical society efforts to create new streams of patient-generated data for clinical and research use. We observe that the key to high-quality patient-generated data is to have immediate and actionable data so that patients experience the importance of the data for their own care as well as research purposes. We conclude that leveraging the emerging wealth of "big data" being generated by patient-facing technologies such as systems to collect patient-reported outcomes data and patient-worn sensors is critical to developing the evidence base that informs decisions made by patients, providers, and policy makers in pursuit of high-value medical care. Project HOPE—The People-to-People Health Foundation, Inc.

Design of a Facility to Test the Advanced Stirling Radioisotope Generator Engineering Unit

NASA Technical Reports Server (NTRS)

Lewandowski, Edward J.; Schreiber, Jeffrey G.; Oriti, Salvatore M.; Meer, David W.; Brace, Michael H.; Dugala, Gina

2010-01-01

The Advanced Stirling Radioisotope Generator (ASRG), a high efficiency generator, is being considered for space missions. An engineering unit, the ASRG engineering unit (EU), was designed and fabricated by Lockheed Martin under contract to the Department of Energy. This unit is currently under extended operation test at the NASA Glenn Research Center (GRC) to generate performance data and validate the life and reliability predictions for the generator and the Stirling convertors. A special test facility was designed and built for the ASRG EU. This paper summarizes details of the test facility design, including the mechanical mounting, heat-rejection system, argon system, control systems, and maintenance. The effort proceeded from requirements definition through design, analysis, build, and test. Initial testing and facility performance results are discussed.

Development of fast neutron radiography system based on portable neutron generator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yi, Chia Jia, E-mail: gei-i-kani@hotmail.com; Nilsuwankosit, Sunchai, E-mail: sunchai.n@chula.ac.th

Due to the high installation cost, the safety concern and the immobility of the research reactors, the neutron radiography system based on portable neutron generator is proposed. Since the neutrons generated from a portable neutron generator are mostly the fast neutrons, the system is emphasized on using the fast neutrons for the purpose of conducting the radiography. In order to suppress the influence of X-ray produced by the neutron generator, a combination of a shielding material sandwiched between two identical imaging plates is used. A binary XOR operation is then applied for combining the information from the imaging plates. Themore » raw images obtained confirm that the X-ray really has a large effect and that XOR operation can help enhance the effect of the neutrons.« less

Online Monitoring Technical Basis and Analysis Framework for Emergency Diesel Generators - Interim Report for FY 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Binh T. Pham; Nancy J. Lybeck; Vivek Agarwal

The Light Water Reactor Sustainability program at Idaho National Laboratory is actively conducting research to develop and demonstrate online monitoring capabilities for active components in existing nuclear power plants. Idaho National Laboratory and the Electric Power Research Institute are working jointly to implement a pilot project to apply these capabilities to emergency diesel generators and generator step-up transformers. The Electric Power Research Institute Fleet-Wide Prognostic and Health Management Software Suite will be used to implement monitoring in conjunction with utility partners: Braidwood Generating Station (owned by Exelon Corporation) for emergency diesel generators, and Shearon Harris Nuclear Generating Station (owned bymore » Duke Energy Progress) for generator step-up transformers. This report presents monitoring techniques, fault signatures, and diagnostic and prognostic models for emergency diesel generators. Emergency diesel generators provide backup power to the nuclear power plant, allowing operation of essential equipment such as pumps in the emergency core coolant system during catastrophic events, including loss of offsite power. Technical experts from Braidwood are assisting Idaho National Laboratory and Electric Power Research Institute in identifying critical faults and defining fault signatures associated with each fault. The resulting diagnostic models will be implemented in the Fleet-Wide Prognostic and Health Management Software Suite and tested using data from Braidwood. Parallel research on generator step-up transformers was summarized in an interim report during the fourth quarter of fiscal year 2012.« less

An image database management system for conducting CAD research

NASA Astrophysics Data System (ADS)

Gruszauskas, Nicholas; Drukker, Karen; Giger, Maryellen L.

2007-03-01

The development of image databases for CAD research is not a trivial task. The collection and management of images and their related metadata from multiple sources is a time-consuming but necessary process. By standardizing and centralizing the methods in which these data are maintained, one can generate subsets of a larger database that match the specific criteria needed for a particular research project in a quick and efficient manner. A research-oriented management system of this type is highly desirable in a multi-modality CAD research environment. An online, webbased database system for the storage and management of research-specific medical image metadata was designed for use with four modalities of breast imaging: screen-film mammography, full-field digital mammography, breast ultrasound and breast MRI. The system was designed to consolidate data from multiple clinical sources and provide the user with the ability to anonymize the data. Input concerning the type of data to be stored as well as desired searchable parameters was solicited from researchers in each modality. The backbone of the database was created using MySQL. A robust and easy-to-use interface for entering, removing, modifying and searching information in the database was created using HTML and PHP. This standardized system can be accessed using any modern web-browsing software and is fundamental for our various research projects on computer-aided detection, diagnosis, cancer risk assessment, multimodality lesion assessment, and prognosis. Our CAD database system stores large amounts of research-related metadata and successfully generates subsets of cases that match the user's desired search criteria.

Organisational capacity and its relationship to research use in six Australian health policy agencies

PubMed Central

Makkar, Steve R.; Haynes, Abby; Williamson, Anna; Redman, Sally

2018-01-01

There are calls for policymakers to make greater use of research when formulating policies. Therefore, it is important that policy organisations have a range of tools and systems to support their staff in using research in their work. The aim of the present study was to measure the extent to which a range of tools and systems to support research use were available within six Australian agencies with a role in health policy, and examine whether this was related to the extent of engagement with, and use of research in policymaking by their staff. The presence of relevant systems and tools was assessed via a structured interview called ORACLe which is conducted with a senior executive from the agency. To measure research use, four policymakers from each agency undertook a structured interview called SAGE, which assesses and scores the extent to which policymakers engaged with (i.e., searched for, appraised, and generated) research, and used research in the development of a specific policy document. The results showed that all agencies had at least a moderate range of tools and systems in place, in particular policy development processes; resources to access and use research (such as journals, databases, libraries, and access to research experts); processes to generate new research; and mechanisms to establish relationships with researchers. Agencies were less likely, however, to provide research training for staff and leaders, or to have evidence-based processes for evaluating existing policies. For the majority of agencies, the availability of tools and systems was related to the extent to which policymakers engaged with, and used research when developing policy documents. However, some agencies did not display this relationship, suggesting that other factors, namely the organisation’s culture towards research use, must also be considered. PMID:29513669

Organisational capacity and its relationship to research use in six Australian health policy agencies.

PubMed

Makkar, Steve R; Haynes, Abby; Williamson, Anna; Redman, Sally

2018-01-01

There are calls for policymakers to make greater use of research when formulating policies. Therefore, it is important that policy organisations have a range of tools and systems to support their staff in using research in their work. The aim of the present study was to measure the extent to which a range of tools and systems to support research use were available within six Australian agencies with a role in health policy, and examine whether this was related to the extent of engagement with, and use of research in policymaking by their staff. The presence of relevant systems and tools was assessed via a structured interview called ORACLe which is conducted with a senior executive from the agency. To measure research use, four policymakers from each agency undertook a structured interview called SAGE, which assesses and scores the extent to which policymakers engaged with (i.e., searched for, appraised, and generated) research, and used research in the development of a specific policy document. The results showed that all agencies had at least a moderate range of tools and systems in place, in particular policy development processes; resources to access and use research (such as journals, databases, libraries, and access to research experts); processes to generate new research; and mechanisms to establish relationships with researchers. Agencies were less likely, however, to provide research training for staff and leaders, or to have evidence-based processes for evaluating existing policies. For the majority of agencies, the availability of tools and systems was related to the extent to which policymakers engaged with, and used research when developing policy documents. However, some agencies did not display this relationship, suggesting that other factors, namely the organisation's culture towards research use, must also be considered.

SAGA: A project to automate the management of software production systems

NASA Technical Reports Server (NTRS)

Campbell, R. H.

1983-01-01

The current work in progress for the SAGA project are described. The highlights of this research are: a parser independent SAGA editor, design for the screen editing facilities of the editor, delivery to NASA of release 1 of Olorin, the SAGA parser generator, personal workstation environment research, release 1 of the SAGA symbol table manager, delta generation in SAGA, requirements for a proof management system, documentation for and testing of the cyber pascal make prototype, a prototype cyber-based slicing facility, a June 1984 demonstration plan, SAGA utility programs, summary of UNIX software engineering support, and theorem prover review.

NASA's Radioisotope Power Systems Program Status

NASA Technical Reports Server (NTRS)

Dudzinski, Leonard A.; Hamley, John A.; McCallum, Peter W.; Sutliff, Thomas J.; Zakrajsek, June F.

2013-01-01

NASA's Radioisotope Power Systems (RPS) Program began formal implementation in December 2010. The RPS Program's goal is to make available RPS for the exploration of the solar system in environments where conventional solar or chemical power generation is impractical or impossible to meet mission needs. To meet this goal, the RPS Program manages investments in RPS system development and RPS technologies. The current keystone of the RPS Program is the development of the Advanced Stirling Radioisotope Generator (ASRG). This generator will be about four times more efficient than the more traditional thermoelectric generators, while providing a similar amount of power. This paper provides the status of the RPS Program and its related projects. Opportunities for RPS generator development and targeted research into RPS component performance enhancements, as well as constraints dealing with the supply of radioisotope fuel, are also discussed in the context of the next ten years of planetary science mission plans.

Narrowing the Gap between Theory and Practice: Proposals for a Fifth Generation of Community Colleges.

ERIC Educational Resources Information Center

Deegan, William L.; Tillery, Dale

1986-01-01

The "fifth generation" of community colleges must assess and resolve fundamental questions of quality and productivity. A research agenda is outlined that addresses mission, delivery systems, student needs, and attendance patterns. (LB)

DOE Office of Scientific and Technical Information (OSTI.GOV)

BARTONE, ERIK

DBS Energy Inc. (“DBS”) intends on using the Connecticut Biofuels Technology Project for the purpose of developing a small-scale electric generating systems that are located on a distributed basis and utilize biodiesel as its principle fuel source. This project will include research and analysis on the quality and applied use of biodiesel for use in electricity production, 2) develop dispatch center for testing and analysis of the reliability of dispatching remote generators operating on a blend of biodiesel and traditional fossil fuels, and 3) analysis and engineering research on fuel storage options for biodiesel of fuels for electric generation.

NASA System-Level Design, Analysis and Simulation Tools Research on NextGen

NASA Technical Reports Server (NTRS)

Bardina, Jorge

2011-01-01

A review of the research accomplished in 2009 in the System-Level Design, Analysis and Simulation Tools (SLDAST) of the NASA's Airspace Systems Program is presented. This research thrust focuses on the integrated system-level assessment of component level innovations, concepts and technologies of the Next Generation Air Traffic System (NextGen) under research in the ASP program to enable the development of revolutionary improvements and modernization of the National Airspace System. The review includes the accomplishments on baseline research and the advancements on design studies and system-level assessment, including the cluster analysis as an annualization standard of the air traffic in the U.S. National Airspace, and the ACES-Air MIDAS integration for human-in-the-loop analyzes within the NAS air traffic simulation.

Hairy Root as a Model System for Undergraduate Laboratory Curriculum and Research

ERIC Educational Resources Information Center

Keyes, Carol A.; Subramanian, Senthil; Yu, Oliver

2009-01-01

Hairy root transformation has been widely adapted in plant laboratories to rapidly generate transgenic roots for biochemical and molecular analysis. We present hairy root transformations as a versatile and adaptable model system for a wide variety of undergraduate laboratory courses and research. This technique is easy, efficient, and fast making…

Energy Systems Integration Newsletter - December 2016 | Energy Systems

Science.gov Websites

in New NSF Big Data Project for Smart Grids NREL is participating in a National Science Foundation control features of modern wind turbine generators. Frew presented research on wholesale market design and industry research. Previous work was cited in numerous European studies, and ERGIS was mentioned as an

Comparing Different Fault Identification Algorithms in Distributed Power System

NASA Astrophysics Data System (ADS)

Alkaabi, Salim

A power system is a huge complex system that delivers the electrical power from the generation units to the consumers. As the demand for electrical power increases, distributed power generation was introduced to the power system. Faults may occur in the power system at any time in different locations. These faults cause a huge damage to the system as they might lead to full failure of the power system. Using distributed generation in the power system made it even harder to identify the location of the faults in the system. The main objective of this work is to test the different fault location identification algorithms while tested on a power system with the different amount of power injected using distributed generators. As faults may lead the system to full failure, this is an important area for research. In this thesis different fault location identification algorithms have been tested and compared while the different amount of power is injected from distributed generators. The algorithms were tested on IEEE 34 node test feeder using MATLAB and the results were compared to find when these algorithms might fail and the reliability of these methods.

Next generation agricultural system data, models and knowledge products: Introduction.

PubMed

Antle, John M; Jones, James W; Rosenzweig, Cynthia E

2017-07-01

Agricultural system models have become important tools to provide predictive and assessment capability to a growing array of decision-makers in the private and public sectors. Despite ongoing research and model improvements, many of the agricultural models today are direct descendants of research investments initially made 30-40 years ago, and many of the major advances in data, information and communication technology (ICT) of the past decade have not been fully exploited. The purpose of this Special Issue of Agricultural Systems is to lay the foundation for the next generation of agricultural systems data, models and knowledge products. The Special Issue is based on a "NextGen" study led by the Agricultural Model Intercomparison and Improvement Project (AgMIP) with support from the Bill and Melinda Gates Foundation.

Next Generation Agricultural System Data, Models and Knowledge Products: Introduction

NASA Technical Reports Server (NTRS)

Antle, John M.; Jones, James W.; Rosenzweig, Cynthia E.

2016-01-01

Agricultural system models have become important tools to provide predictive and assessment capability to a growing array of decision-makers in the private and public sectors. Despite ongoing research and model improvements, many of the agricultural models today are direct descendants of research investments initially made 30-40 years ago, and many of the major advances in data, information and communication technology (ICT) of the past decade have not been fully exploited. The purpose of this Special Issue of Agricultural Systems is to lay the foundation for the next generation of agricultural systems data, models and knowledge products. The Special Issue is based on a 'NextGen' study led by the Agricultural Model Intercomparison and Improvement Project (AgMIP) with support from the Bill and Melinda Gates Foundation.

Research Evaluation and the Assessment of Public Value

ERIC Educational Resources Information Center

Molas-Gallart, Jordi

2015-01-01

Funding organisations are increasingly asking academics to show evidence of the economic and social value generated by their research. These requests have often been associated with the emergence of a so-called "new social contract for research" and are related to the implementation of new research evaluation systems. Although the…

Systems and Software Producibility Collaboration and Experimental Environment (SPRUCE)

DTIC Science & Technology

2009-04-23

Research Manhattan Project Like Research – Transition timeframe needed • Current generation programs – DoD acquisitions over next 1-5 years • Next...Specific Computing Plant B a s i c Transformational Research Manhattan Project Like Research B a s i c 16 • Sponsored by Lockheed Martin

Survey of Approaches to Generate Realistic Synthetic Graphs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lim, Seung-Hwan; Lee, Sangkeun; Powers, Sarah S

A graph is a flexible data structure that can represent relationships between entities. As with other data analysis tasks, the use of realistic graphs is critical to obtaining valid research results. Unfortunately, using the actual ("real-world") graphs for research and new algorithm development is difficult due to the presence of sensitive information in the data or due to the scale of data. This results in practitioners developing algorithms and systems that employ synthetic graphs instead of real-world graphs. Generating realistic synthetic graphs that provide reliable statistical confidence to algorithmic analysis and system evaluation involves addressing technical hurdles in a broadmore » set of areas. This report surveys the state of the art in approaches to generate realistic graphs that are derived from fitted graph models on real-world graphs.« less

A Framework for Curriculum Research.

ERIC Educational Resources Information Center

Kimpston, Richard D.; Rogers, Karen B.

1986-01-01

A framework for generating curriculum research is proposed from a synthesis of Dunkin and Biddle's model of teaching variables with Beauchamp's "curriculum system" planning functions. The framework systematically defines variables that delineate curriculum planning processes. (CJH)

A Study Using a Monte Carlo Method of the Optimal Configuration of a Distribution Network in Terms of Power Loss Sensing

PubMed Central

Moon, Hyun Ho; Lee, Jong Joo; Choi, Sang Yule; Cha, Jae Sang; Kang, Jang Mook; Kim, Jong Tae; Shin, Myong Chul

2011-01-01

Recently there have been many studies of power systems with a focus on “New and Renewable Energy” as part of “New Growth Engine Industry” promoted by the Korean government. “New And Renewable Energy”—especially focused on wind energy, solar energy and fuel cells that will replace conventional fossil fuels—is a part of the Power-IT Sector which is the basis of the SmartGrid. A SmartGrid is a form of highly-efficient intelligent electricity network that allows interactivity (two-way communications) between suppliers and consumers by utilizing information technology in electricity production, transmission, distribution and consumption. The New and Renewable Energy Program has been driven with a goal to develop and spread through intensive studies, by public or private institutions, new and renewable energy which, unlike conventional systems, have been operated through connections with various kinds of distributed power generation systems. Considerable research on smart grids has been pursued in the United States and Europe. In the United States, a variety of research activities on the smart power grid have been conducted within EPRI’s IntelliGrid research program. The European Union (EU), which represents Europe’s Smart Grid policy, has focused on an expansion of distributed generation (decentralized generation) and power trade between countries with improved environmental protection. Thus, there is current emphasis on a need for studies that assesses the economic efficiency of such distributed generation systems. In this paper, based on the cost of distributed power generation capacity, calculations of the best profits obtainable were made by a Monte Carlo simulation. Monte Carlo simulations that rely on repeated random sampling to compute their results take into account the cost of electricity production, daily loads and the cost of sales and generate a result faster than mathematical computations. In addition, we have suggested the optimal design, which considers the distribution loss associated with power distribution systems focus on sensing aspect and distributed power generation. PMID:22164047

Power processing and control requirements of dispersed solar thermal electric generation systems

NASA Technical Reports Server (NTRS)

Das, R. L.

1980-01-01

Power Processing and Control requirements of Dispersed Receiver Solar Thermal Electric Generation Systems are presented. Kinematic Stirling Engines, Brayton Engines and Rankine Engines are considered as prime movers. Various types of generators are considered for ac and dc link generations. It is found that ac-ac Power Conversion is not suitable for implementation at this time. It is also found that ac-dc-ac Power Conversion with a large central inverter is more efficient than ac-dc-ac Power Conversion using small dispersed inverters. Ac-link solar thermal electric plants face potential stability and synchronization problems. Research and development efforts are needed in improving component performance characteristics and generation efficiency to make Solar Thermal Electric Generation economically attractive.

Parallel-Processing Test Bed For Simulation Software

NASA Technical Reports Server (NTRS)

Blech, Richard; Cole, Gary; Townsend, Scott

1996-01-01

Second-generation Hypercluster computing system is multiprocessor test bed for research on parallel algorithms for simulation in fluid dynamics, electromagnetics, chemistry, and other fields with large computational requirements but relatively low input/output requirements. Built from standard, off-shelf hardware readily upgraded as improved technology becomes available. System used for experiments with such parallel-processing concepts as message-passing algorithms, debugging software tools, and computational steering. First-generation Hypercluster system described in "Hypercluster Parallel Processor" (LEW-15283).

Electric Power Generation Systems for Use in Space

DTIC Science & Technology

1960-07-20

source of power . It is available from two sources, namely, nuclear fission and radioisotope decay. In both cases, the energy is available in...limitations on inventory size as well as spe- cific weight considerations will restrict radioisotope systems to power levels below about 1 kilowatt. It is... POWER GENERATION SYSTEMS FOR USE IN SPA TIC By Henry 0. Slone and Seymour Lieblein -y 6, "IN 13 pLewis Research Center G 0 3 1994 Nation Aeronautics

Text Generation: The State of the Art and the Literature.

ERIC Educational Resources Information Center

Mann, William C.; And Others

This report comprises two documents which describe the state of the art of computer generation of natural language text. Both were prepared by a panel of individuals who are active in research on text generation. The first document assesses the techniques now available for use in systems design, covering all of the technical methods by which…

Experimental study of camel powered electricity generation unit

NASA Astrophysics Data System (ADS)

Jakhar, O. P.; Choudhary, Rahul Raj; Budaniya, Mukesh; Kumar, Ashish

2018-05-01

Developing nations are facing a huge gap in generation and demand of electricity across the world. In present scenario the demand of electricity is increasing day by day and the shortfall of electricity has become one of the major obstructions in the development of rural areas. There is a big gap between electricity supply and demand. In India it is very difficult that to give twenty four hours electric supply in rural areas. The traditional use of camel as draught animal, for the purpose of transport of goods and agricultural work, has been drastically reduced during last few decades, due to advancements and cheaper availability of mechanical machineries. In this research paper we experimentally studied the camel powered electricity generation system at National Research Centre on Camels (NRCC) Bikaner. Camel Energy in form of high torque low speed can be converted into low torque high speed through motion converting system i.e. gear and pulley mechanism for high RPM output. This high RPM (more than 3000) output is used for electricity generation. The electricity generated can be used directly or stored in the battery and later may be used whenever it is required either for DC light or AC light using inverter. According to experimental study a camel can comfortably generate electricity up to 1KW by rotating shaft. The complete set up for electricity generation using camel power has been designed, developed and physically commissioned at National Research Centre on Camels (NRCC) Bikaner.

Stabilization of Wind Energy Conversion System with Hydrogen Generator by Using EDLC Energy Storage System

NASA Astrophysics Data System (ADS)

Shishido, Seiji; Takahashi, Rion; Murata, Toshiaki; Tamura, Junji; Sugimasa, Masatoshi; Komura, Akiyoshi; Futami, Motoo; Ichinose, Masaya; Ide, Kazumasa

The spread of wind power generation is progressed hugely in recent years from a viewpoint of environmental problems including global warming. Though wind power is considered as a very prospective energy source, wind power fluctuation due to the random fluctuation of wind speed has still created some problems. Therefore, research has been performed how to smooth the wind power fluctuation. This paper proposes Energy Capacitor System (ECS) for the smoothing of wind power which consists of Electric Double-Layer Capacitor (EDLC) and power electronics devices and works as an electric power storage system. Moreover, hydrogen has received much attention in recent years from a viewpoint of exhaustion problem of fossil fuel. Therefore it is also proposed that a hydrogen generator is installed at the wind farm to generate hydrogen. In this paper, the effectiveness of the proposed system is verified by the simulation analyses using PSCAD/EMTDC.

Space station electrical power system availability study

NASA Technical Reports Server (NTRS)

Turnquist, Scott R.; Twombly, Mark A.

1988-01-01

ARINC Research Corporation performed a preliminary reliability, and maintainability (RAM) anlaysis of the NASA space station Electric Power Station (EPS). The analysis was performed using the ARINC Research developed UNIRAM RAM assessment methodology and software program. The analysis was performed in two phases: EPS modeling and EPS RAM assessment. The EPS was modeled in four parts: the insolar power generation system, the eclipse power generation system, the power management and distribution system (both ring and radial power distribution control unit (PDCU) architectures), and the power distribution to the inner keel PDCUs. The EPS RAM assessment was conducted in five steps: the use of UNIRAM to perform baseline EPS model analyses and to determine the orbital replacement unit (ORU) criticalities; the determination of EPS sensitivity to on-orbit spared of ORUs and the provision of an indication of which ORUs may need to be spared on-orbit; the determination of EPS sensitivity to changes in ORU reliability; the determination of the expected annual number of ORU failures; and the integration of the power generator system model results with the distribution system model results to assess the full EPS. Conclusions were drawn and recommendations were made.

46 CFR 195.05-1 - Installation and details.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS VESSEL... of this type include the following: Ship's Service Generating Systems. Ship's Service Power... Lighting and Power Systems. Electric Lifeboat Winch Systems. Electric Steering Gear and Steering Control...

Brief history of agricultural systems modeling.

PubMed

Jones, James W; Antle, John M; Basso, Bruno; Boote, Kenneth J; Conant, Richard T; Foster, Ian; Godfray, H Charles J; Herrero, Mario; Howitt, Richard E; Janssen, Sander; Keating, Brian A; Munoz-Carpena, Rafael; Porter, Cheryl H; Rosenzweig, Cynthia; Wheeler, Tim R

2017-07-01

Agricultural systems science generates knowledge that allows researchers to consider complex problems or take informed agricultural decisions. The rich history of this science exemplifies the diversity of systems and scales over which they operate and have been studied. Modeling, an essential tool in agricultural systems science, has been accomplished by scientists from a wide range of disciplines, who have contributed concepts and tools over more than six decades. As agricultural scientists now consider the "next generation" models, data, and knowledge products needed to meet the increasingly complex systems problems faced by society, it is important to take stock of this history and its lessons to ensure that we avoid re-invention and strive to consider all dimensions of associated challenges. To this end, we summarize here the history of agricultural systems modeling and identify lessons learned that can help guide the design and development of next generation of agricultural system tools and methods. A number of past events combined with overall technological progress in other fields have strongly contributed to the evolution of agricultural system modeling, including development of process-based bio-physical models of crops and livestock, statistical models based on historical observations, and economic optimization and simulation models at household and regional to global scales. Characteristics of agricultural systems models have varied widely depending on the systems involved, their scales, and the wide range of purposes that motivated their development and use by researchers in different disciplines. Recent trends in broader collaboration across institutions, across disciplines, and between the public and private sectors suggest that the stage is set for the major advances in agricultural systems science that are needed for the next generation of models, databases, knowledge products and decision support systems. The lessons from history should be considered to help avoid roadblocks and pitfalls as the community develops this next generation of agricultural systems models.

Brief history of agricultural systems modeling

DOE PAGES

Jones, James W.; Antle, John M.; Basso, Bruno; ...

2017-06-21

Agricultural systems science generates knowledge that allows researchers to consider complex problems or take informed agricultural decisions. The rich history of this science exemplifies the diversity of systems and scales over which they operate and have been studied. Modeling, an essential tool in agricultural systems science, has been accomplished by scientists from a wide range of disciplines, who have contributed concepts and tools over more than six decades. As agricultural scientists now consider the "next generation" models, data, and knowledge products needed to meet the increasingly complex systems problems faced by society, it is important to take stock of thismore » history and its lessons to ensure that we avoid re-invention and strive to consider all dimensions of associated challenges. To this end, we summarize here the history of agricultural systems modeling and identify lessons learned that can help guide the design and development of next generation of agricultural system tools and methods. A number of past events combined with overall technological progress in other fields have strongly contributed to the evolution of agricultural system modeling, including development of process-based bio-physical models of crops and livestock, statistical models based on historical observations, and economic optimization and simulation models at household and regional to global scales. Characteristics of agricultural systems models have varied widely depending on the systems involved, their scales, and the wide range of purposes that motivated their development and use by researchers in different disciplines. Recent trends in broader collaboration across institutions, across disciplines, and between the public and private sectors suggest that the stage is set for the major advances in agricultural systems science that are needed for the next generation of models, databases, knowledge products and decision support systems. Furthermore, the lessons from history should be considered to help avoid roadblocks and pitfalls as the community develops this next generation of agricultural systems models.« less

Brief history of agricultural systems modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, James W.; Antle, John M.; Basso, Bruno

Agricultural systems science generates knowledge that allows researchers to consider complex problems or take informed agricultural decisions. The rich history of this science exemplifies the diversity of systems and scales over which they operate and have been studied. Modeling, an essential tool in agricultural systems science, has been accomplished by scientists from a wide range of disciplines, who have contributed concepts and tools over more than six decades. As agricultural scientists now consider the "next generation" models, data, and knowledge products needed to meet the increasingly complex systems problems faced by society, it is important to take stock of thismore » history and its lessons to ensure that we avoid re-invention and strive to consider all dimensions of associated challenges. To this end, we summarize here the history of agricultural systems modeling and identify lessons learned that can help guide the design and development of next generation of agricultural system tools and methods. A number of past events combined with overall technological progress in other fields have strongly contributed to the evolution of agricultural system modeling, including development of process-based bio-physical models of crops and livestock, statistical models based on historical observations, and economic optimization and simulation models at household and regional to global scales. Characteristics of agricultural systems models have varied widely depending on the systems involved, their scales, and the wide range of purposes that motivated their development and use by researchers in different disciplines. Recent trends in broader collaboration across institutions, across disciplines, and between the public and private sectors suggest that the stage is set for the major advances in agricultural systems science that are needed for the next generation of models, databases, knowledge products and decision support systems. Furthermore, the lessons from history should be considered to help avoid roadblocks and pitfalls as the community develops this next generation of agricultural systems models.« less

Brief History of Agricultural Systems Modeling

NASA Technical Reports Server (NTRS)

Jones, James W.; Antle, John M.; Basso, Bruno O.; Boote, Kenneth J.; Conant, Richard T.; Foster, Ian; Godfray, H. Charles J.; Herrrero, Mario; Howitt, Richard E.; Janssen, Sandor;

A flexible telerobotic system for space operations

NASA Technical Reports Server (NTRS)

Sliwa, N. O.; Will, R. W.

1987-01-01

The objective and design of a proposed goal-oriented knowledge-based telerobotic system for space operations is described. This design effort encompasses the elements of the system executive and user interface and the distribution and general structure of the knowledge base, the displays, and the task sequencing. The objective of the design effort is to provide an expandable structure for a telerobotic system that provides cooperative interaction between the human operator and computer control. The initial phase of the implementation provides a rule-based, goal-oriented script generator to interface to the existing control modes of a telerobotic research system, in the Intelligent Systems Research Lab at NASA Research Center.

Crowdsourced social media monitoring system development.

DOT National Transportation Integrated Search

2017-08-01

Crowdsourcing is a relatively new area of research, but it is already generating an enormous amount of interest among both researchers and practitioners, and is finding applications in multiple domains. It is particularly useful for efficient traffic...

Information for Institutional Renewal.

ERIC Educational Resources Information Center

Spencer, Richard L.

1979-01-01

Discusses a planning, management, and evaluation system, an objective-based planning process, research databases, analytical reports, and transactional data as state-of-the-art tools available to generate data which link research directly to planning for institutional renewal. (RC)

Research of hydroelectric generating set low-frequency vibration monitoring system based on optical fiber sensing

NASA Astrophysics Data System (ADS)

Min, Li; Zhang, Xiaolei; Zhang, Faxiang; Sun, Zhihui; Li, ShuJuan; Wang, Meng; Wang, Chang

2017-10-01

In order to satisfy hydroelectric generating set low-frequency vibration monitoring, the design of Passive low-frequency vibration monitoring system based on Optical fiber sensing in this paper. The hardware of the system adopts the passive optical fiber grating sensor and unbalanced-Michelson interferometer. The software system is used to programming by Labview software and finishing the control of system. The experiment show that this system has good performance on the standard vibration testing-platform and it meets system requirements. The frequency of the monitoring system can be as low as 0.2Hz and the resolution is 0.01Hz.

Knowledge-based approach for generating target system specifications from a domain model

NASA Technical Reports Server (NTRS)

Gomaa, Hassan; Kerschberg, Larry; Sugumaran, Vijayan

1992-01-01

Several institutions in industry and academia are pursuing research efforts in domain modeling to address unresolved issues in software reuse. To demonstrate the concepts of domain modeling and software reuse, a prototype software engineering environment is being developed at George Mason University to support the creation of domain models and the generation of target system specifications. This prototype environment, which is application domain independent, consists of an integrated set of commercial off-the-shelf software tools and custom-developed software tools. This paper describes the knowledge-based tool that was developed as part of the environment to generate target system specifications from a domain model.

ELI-Beamlines: development of next generation short-pulse laser systems

NASA Astrophysics Data System (ADS)

Rus, B.; Bakule, P.; Kramer, D.; Naylon, J.; Thoma, J.; Green, J. T.; Antipenkov, R.; Fibrich, M.; Novák, J.; Batysta, F.; Mazanec, T.; Drouin, M. A.; Kasl, K.; Baše, R.; Peceli, D.; Koubíková, L.; Trojek, P.; Boge, R.; Lagron, J. C.; Vyhlídka, Å.; Weiss, J.; Cupal, J.,; Hřebíček, J.; Hříbek, P.; Durák, M.; Polan, J.; Košelja, M.; Korn, G.; Horáček, M.; Horáček, J.; Himmel, B.; Havlíček, T.; Honsa, A.; Korouš, P.; Laub, M.; Haefner, C.; Bayramian, A.; Spinka, T.; Marshall, C.; Johnson, G.; Telford, S.; Horner, J.; Deri, B.; Metzger, T.; Schultze, M.; Mason, P.; Ertel, K.; Lintern, A.; Greenhalgh, J.; Edwards, C.; Hernandez-Gomez, C.; Collier, J.; Ditmire, T.,; Gaul, E.; Martinez, M.; Frederickson, C.; Hammond, D.; Malato, C.; White, W.; Houžvička, J.

2015-05-01

Overview of the laser systems being built for ELI-Beamlines is presented. The facility will make available high-brightness multi-TW ultrashort laser pulses at kHz repetition rate, PW 10 Hz repetition rate pulses, and kilojoule nanosecond pulses for generation of 10 PW peak power. The lasers will extensively employ the emerging technology of diode-pumped solid-state lasers (DPSSL) to pump OPCPA and Ti:sapphire broadband amplifiers. These systems will provide the user community with cutting-edge laser resources for programmatic research in generation and applications of high-intensity X-ray sources, in particle acceleration, and in dense-plasma and high-field physics.

Guidance of Nonlinear Nonminimum-Phase Dynamic Systems

NASA Technical Reports Server (NTRS)

Devasia, Santosh

1997-01-01

The first two years research work has advanced the inversion-based guidance theory for: (1) systems with non-hyperbolic internal dynamics; (2) systems with parameter jumps; (3) systems where a redesign of the output trajectory is desired; and (4) the generation of recovery guidance maneuvers.

Implementation of Consolidated HIS: Improving Quality and Efficiency of Healthcare

PubMed Central

Choi, Jinwook; Seo, Jeong-Wook; Chung, Chun Kee; Kim, Kyung-Hwan; Kim, Ju Han; Kim, Jong Hyo; Chie, Eui Kyu; Cho, Hyun-Jai; Goo, Jin Mo; Lee, Hyuk-Joon; Wee, Won Ryang; Nam, Sang Mo; Lim, Mi-Sun; Kim, Young-Ah; Yang, Seung Hoon; Jo, Eun Mi; Hwang, Min-A; Kim, Wan Suk; Lee, Eun Hye; Choi, Su Hi

2010-01-01

Objectives Adoption of hospital information systems offers distinctive advantages in healthcare delivery. First, implementation of consolidated hospital information system in Seoul National University Hospital led to significant improvements in quality of healthcare and efficiency of hospital management. Methods The hospital information system in Seoul National University Hospital consists of component applications: clinical information systems, clinical research support systems, administrative information systems, management information systems, education support systems, and referral systems that operate to generate utmost performance when delivering healthcare services. Results Clinical information systems, which consist of such applications as electronic medical records, picture archiving and communication systems, primarily support clinical activities. Clinical research support system provides valuable resources supporting various aspects of clinical activities, ranging from management of clinical laboratory tests to establishing care-giving procedures. Conclusions Seoul National University Hospital strives to move its hospital information system to a whole new level, which enables customized healthcare service and fulfills individual requirements. The current information strategy is being formulated as an initial step of development, promoting the establishment of next-generation hospital information system. PMID:21818449

System description and requirements document.

DOT National Transportation Integrated Search

2007-10-10

The Next Generation 911 Initiative (NG911) : is a U.S. Department of Transportation (USDOT) : research and development project that will help : define the system architecture and develop a : transition plan that considers responsibilities...

Smart campus: Data on energy generation costs from distributed generation systems of electrical energy in a Nigerian University.

PubMed

Okeniyi, Joshua O; Atayero, Aderemi A; Popoola, Segun I; Okeniyi, Elizabeth T; Alalade, Gbenga M

2018-04-01

This data article presents comparisons of energy generation costs from gas-fired turbine and diesel-powered systems of distributed generation type of electrical energy in Covenant University, Ota, Nigeria, a smart university campus driven by Information and Communication Technologies (ICT). Cumulative monthly data of the energy generation costs, for consumption in the institution, from the two modes electric power, which was produced at locations closed to the community consuming the energy, were recorded for the period spanning January to December 2017. By these, energy generation costs from the turbine system proceed from the gas-firing whereas the generation cost data from the diesel-powered generator also include data on maintenance cost for this mode of electrical power generation. These energy generation cost data that were presented in tables and graphs employ descriptive probability distribution and goodness-of-fit tests of statistical significance as the methods for the data detailing and comparisons. Information details from this data of energy generation costs are useful for furthering research developments and aiding energy stakeholders and decision-makers in the formulation of policies on energy generation modes, economic valuation in terms of costing and management for attaining energy-efficient/smart educational environment.

A Concurrent Distributed System for Aircraft Tactical Decision Generation

NASA Technical Reports Server (NTRS)

McManus, John W.

1990-01-01

A research program investigating the use of artificial intelligence (AI) techniques to aid in the development of a Tactical Decision Generator (TDG) for Within Visual Range (WVR) air combat engagements is discussed. The application of AI programming and problem solving methods in the development and implementation of a concurrent version of the Computerized Logic For Air-to-Air Warfare Simulations (CLAWS) program, a second generation TDG, is presented. Concurrent computing environments and programming approaches are discussed and the design and performance of a prototype concurrent TDG system are presented.

Research and realization of signal simulation on virtual instrument

NASA Astrophysics Data System (ADS)

Zhao, Qi; He, Wenting; Guan, Xiumei

2010-02-01

In the engineering project, arbitrary waveform generator controlled by software interface is needed by simulation and test. This article discussed the program using the SCPI (Standard Commands For Programmable Instruments) protocol and the VISA (Virtual Instrument System Architecture) library to control the Agilent signal generator (Agilent N5182A) by instrument communication over the LAN interface. The program can conduct several signal generations such as CW (continuous wave), AM (amplitude modulation), FM (frequency modulation), ΦM (phase modulation), Sweep. As the result, the program system has good operability and portability.

Measurements of Low-Frequency Acoustic Attenuation in Soils.

DTIC Science & Technology

1994-10-13

Engineering Research Laboratory to design an acoustic subsurface imaging system, a set of experiments was conducted in which the attenuation and the velocity...support of the U.S. Army Construction Engineering Research Laboratory’s efforts to design an acoustic subsurface imaging system which would ideally be...of acoustic waves such as those generated by a subsurface imaging system. An experiment reported in the literature characterized the acoustic

Detailed Modeling and Irreversible Transfer Process Analysis of a Multi-Element Thermoelectric Generator System

NASA Astrophysics Data System (ADS)

Xiao, Heng; Gou, Xiaolong; Yang, Suwen

2011-05-01

Thermoelectric (TE) power generation technology, due to its several advantages, is becoming a noteworthy research direction. Many researchers conduct their performance analysis and optimization of TE devices and related applications based on the generalized thermoelectric energy balance equations. These generalized TE equations involve the internal irreversibility of Joule heating inside the thermoelectric device and heat leakage through the thermoelectric couple leg. However, it is assumed that the thermoelectric generator (TEG) is thermally isolated from the surroundings except for the heat flows at the cold and hot junctions. Since the thermoelectric generator is a multi-element device in practice, being composed of many fundamental TE couple legs, the effect of heat transfer between the TE couple leg and the ambient environment is not negligible. In this paper, based on basic theories of thermoelectric power generation and thermal science, detailed modeling of a thermoelectric generator taking account of the phenomenon of energy loss from the TE couple leg is reported. The revised generalized thermoelectric energy balance equations considering the effect of heat transfer between the TE couple leg and the ambient environment have been derived. Furthermore, characteristics of a multi-element thermoelectric generator with irreversibility have been investigated on the basis of the new derived TE equations. In the present investigation, second-law-based thermodynamic analysis (exergy analysis) has been applied to the irreversible heat transfer process in particular. It is found that the existence of the irreversible heat convection process causes a large loss of heat exergy in the TEG system, and using thermoelectric generators for low-grade waste heat recovery has promising potential. The results of irreversibility analysis, especially irreversible effects on generator system performance, based on the system model established in detail have guiding significance for the development and application of thermoelectric generators, particularly for the design and optimization of TE modules.

Computer-generated, calligraphic, full-spectrum color system for visual simulation landing approach maneuvers

NASA Technical Reports Server (NTRS)

Chase, W. D.

1975-01-01

The calligraphic chromatic projector described was developed to improve the perceived realism of visual scene simulation ('out-the-window visuals'). The optical arrangement of the projector is illustrated and discussed. The device permits drawing 2000 vectors in as many as 500 colors, all above critical flicker frequencies, and use of high scene resolution and brightness at an acceptable level to the pilot, with the maximum system capabilities of 1000 lines and 1000 fL. The device for generating the colors is discussed, along with an experiment conducted to demonstrate potential improvements in performance and pilot opinion. Current research work and future research plans are noted.

Collaborative research in the model spinal cord injury systems: process and outcomes.

PubMed

Richards, J Scott

2002-01-01

To review the way in which collaborative research has been conducted under the National Institute on Disability and Rehabilitation Research (NIDRR)-funded Model Spinal Cord Injury Systems (MSCIS) Program, changes made in that process, and significant outcomes. A comparison of changes by NIDRR in the way collaborative research was competed and funded in the 1 995 and 2001 competitions. A review of outcomes of the 1 995 collaborative projects was based on queries to lead centers. Collaborative research through the model SCI systems has been conducted and continues to be conducted through 2 main venues: The National Spinal Cord Injury Statistical Center (NSCISC) database, which has provided data for a number of collaborative studies, and specifically funded proposals for collaborative research. In the 1995 competition for NIDRR funding, collaborative research proposals were submitted as part of the Model SCI Systems competitive applications. In the 2001 competition, collaborative research was parceled out and a separate competition held. There have been a number of publications stemming from the 1 995 competition; some of the data from these projects are still being explored and used for manuscripts. The outcomes for the 2001 competition will not be known for several years. Collaborative research has the advantage of generating larger numbers more quickly than any 1 center can typically generate, producing a more broadly based sample and, therefore, generalizable result, and facilitating the use of expertise not always available in a single center. Collaborative research activities have been among the most productive aspects of the Model Systems program; the change in the way this component is competed in the most recent competition is yet to be evaluated in terms of its efficacy compared with methods used for funding collaborative research in past competitions.

Center for the Built Environment: Research on Controls and Information

Science.gov Websites

and Control Sustainability and Whole Building Energy Publications Research Area : Research on Human Interactions Contributing to the next generation of high-performance building control systems. New information for sensing and control of buildings using wireless communications technology, micro-electromechancial

The Bionic Clicker Mark I & II

PubMed Central

Magee, Elliott G.; Ourselin, S.; Nikitichev, Daniil; Vercauteren, T.; Vanhoestenberghe, Anne

2017-01-01

In this manuscript, we present two 'Bionic Clicker' systems, the first designed to demonstrate electromyography (EMG) based control systems for educational purposes and the second for research purposes. EMG based control systems pick up electrical signals generated by muscle activation and use these as inputs for controllers. EMG controllers are widely used in prosthetics to control limbs. The Mark I (MK I) clicker allows the wearer to change the slide of a presentation by raising their index finger. It is built around a microcontroller and a bio-signals shield. It generated a lot of interest from both the public and research community. The Mark II (MK II) device presented here was designed to be a cheaper, sleeker, and more customizable system that can be easily modified and directly transmit EMG data. It is built using a wireless capable microcontroller and a muscle sensor. PMID:28829413

The Bionic Clicker Mark I & II.

PubMed

Magee, Elliott G; Ourselin, S; Nikitichev, Daniil; Vercauteren, T; Vanhoestenberghe, Anne

2017-08-14

In this manuscript, we present two 'Bionic Clicker' systems, the first designed to demonstrate electromyography (EMG) based control systems for educational purposes and the second for research purposes. EMG based control systems pick up electrical signals generated by muscle activation and use these as inputs for controllers. EMG controllers are widely used in prosthetics to control limbs. The Mark I (MK I) clicker allows the wearer to change the slide of a presentation by raising their index finger. It is built around a microcontroller and a bio-signals shield. It generated a lot of interest from both the public and research community. The Mark II (MK II) device presented here was designed to be a cheaper, sleeker, and more customizable system that can be easily modified and directly transmit EMG data. It is built using a wireless capable microcontroller and a muscle sensor.

Research on Efficiency of a Wave Energy Conversion System

NASA Astrophysics Data System (ADS)

Lu, Zhongyue; Shang, Jianzhong; Luo, Zirong; Sun, Chongfei; Chen, Gewei

2018-02-01

The oceans are rich in wave energy that is green energy, and the wave energy are now being used to generate electricity on a massive scale. It can also be used as a single generator for beacon, buoy or underwater vehicle. Micro small wave energy power generation device is a kind of wave energy power generation devices, main characteristic is mobility is good, and can be directly assembled on various kinds of equipment for the power supply, with good prospects for development. The research object of the paper is a new adaptive reversing wave energy generating device belongs to micro-sized wave energy generating device. Using the upper and lower absorber blade groups, the low speed and large torque wave energy can be converted into electric energy which can be used for load and lithium battery charging.

GenomicDataCommonsNewsNote

Cancer.gov

NCI is establishing the Genomic Data Commons to store, analyze and distribute cancer genomics data generated by NCI and other research organizations. The GDC will provide an interactive system for researchers to access data, with the goal of advancing the

Development of Thermoelectric Power Generation and Peltier Cooling Properties of Materials for Thermoelectric Cryocooling Devices

DTIC Science & Technology

2015-05-12

method. AAMU would like to continue, given future research funding, with our new design for the thermoelectric and photovoltaic systems and hybrid...nanofabrication to develop nanostructured thermoelectric (TE) materials for application in high-efficiency thermoelectric power generators and solid...Distribution Unlimited Final Report: Development of Thermoelectric Power Generation and Peltier Cooling Properties of Materials for Thermoelectric

Application of electrochemical energy storage in solar thermal electric generation systems

NASA Technical Reports Server (NTRS)

Das, R.; Krauthamer, S.; Frank, H.

1982-01-01

This paper assesses the status, cost, and performance of existing electrochemical energy storage systems, and projects the cost, performance, and availability of advanced storage systems for application in terrestrial solar thermal electric generation. A 10 MWe solar plant with five hours of storage is considered and the cost of delivered energy is computed for sixteen different storage systems. The results indicate that the five most attractive electrochemical storage systems use the following battery types: zinc-bromine (Exxon), iron-chromium redox (NASA/Lewis Research Center, LeRC), sodium-sulfur (Ford), sodium-sulfur (Dow), and zinc-chlorine (Energy Development Associates, EDA).

Status of wind-energy conversion

NASA Technical Reports Server (NTRS)

Thomas, R. L.; Savino, J. M.

1973-01-01

The utilization of wind energy is technically feasible as evidenced by the many past demonstrations of wind generators. The cost of energy from the wind has been high compared to fossil fuel systems. A sustained development effort is needed to obtain economical systems. The variability of the wind makes it an unreliable source on a short-term basis. However, the effects of this variability can be reduced by storage systems or connecting wind generators to fossil fuel systems, hydroelectric systems, or dispersing them throughout a large grid network. The NSF and NASA-Lewis Research Center have sponsored programs for the utilization of wind energy.

Entropy, pumped-storage and energy system finance

NASA Astrophysics Data System (ADS)

Karakatsanis, Georgios

2015-04-01

Pumped-storage holds a key role for integrating renewable energy units with non-renewable fuel plants into large-scale energy systems of electricity output. An emerging issue is the development of financial engineering models with physical basis to systematically fund energy system efficiency improvements across its operation. A fundamental physically-based economic concept is the Scarcity Rent; which concerns the pricing of a natural resource's scarcity. Specifically, the scarcity rent comprises a fraction of a depleting resource's full price and accumulates to fund its more efficient future use. In an integrated energy system, scarcity rents derive from various resources and can be deposited to a pooled fund to finance the energy system's overall efficiency increase; allowing it to benefit from economies of scale. With pumped-storage incorporated to the system, water upgrades to a hub resource, in which the scarcity rents of all connected energy sources are denominated to. However, as available water for electricity generation or storage is also limited, a scarcity rent upon it is also imposed. It is suggested that scarcity rent generation is reducible to three (3) main factors, incorporating uncertainty: (1) water's natural renewability, (2) the energy system's intermittent components and (3) base-load prediction deviations from actual loads. For that purpose, the concept of entropy is used in order to measure the energy system's overall uncertainty; hence pumped-storage intensity requirements and generated water scarcity rents. Keywords: pumped-storage, integration, energy systems, financial engineering, physical basis, Scarcity Rent, pooled fund, economies of scale, hub resource, uncertainty, entropy Acknowledgement: This research was funded by the Greek General Secretariat for Research and Technology through the research project Combined REnewable Systems for Sustainable ENergy DevelOpment (CRESSENDO; grant number 5145)

Decision Support Systems for Research and Management in Advanced Life Support

NASA Technical Reports Server (NTRS)

Rodriquez, Luis F.

2004-01-01

Decision support systems have been implemented in many applications including strategic planning for battlefield scenarios, corporate decision making for business planning, production planning and control systems, and recommendation generators like those on Amazon.com(Registered TradeMark). Such tools are reviewed for developing a similar tool for NASA's ALS Program. DSS are considered concurrently with the development of the OPIS system, a database designed for chronicling of research and development in ALS. By utilizing the OPIS database, it is anticipated that decision support can be provided to increase the quality of decisions by ALS managers and researchers.

ERDA/Lewis research center photovoltaic systems test facility

NASA Technical Reports Server (NTRS)

Forestieri, A. F.; Johnson, J. A.; Knapp, W. D.; Rigo, H.; Stover, J.; Suhay, R.

1977-01-01

A national photovoltaic power systems test facility (of initial 10-kW peak power rating) is described. It consists of a solar array to generate electrical power, test-hardware for several alternate methods of power conversion, electrical energy storage systems, and an instrumentation and data acquisition system.

Utility interconnection issues for wind power generation

NASA Technical Reports Server (NTRS)

Herrera, J. I.; Lawler, J. S.; Reddoch, T. W.; Sullivan, R. L.

1986-01-01

This document organizes the total range of utility related issues, reviews wind turbine control and dynamic characteristics, identifies the interaction of wind turbines to electric utility systems, and identifies areas for future research. The material is organized at three levels: the wind turbine, its controls and characteristics; connection strategies as dispersed or WPSs; and the composite issue of planning and operating the electric power system with wind generated electricity.

Fabric-based integrated energy devices for wearable activity monitors.

PubMed

Jung, Sungmook; Lee, Jongsu; Hyeon, Taeghwan; Lee, Minbaek; Kim, Dae-Hyeong

2014-09-01

A wearable fabric-based integrated power-supply system that generates energy triboelectrically using human activity and stores the generated energy in an integrated supercapacitor is developed. This system can be utilized as either a self-powered activity monitor or as a power supply for external wearable sensors. These demonstrations give new insights for the research of wearable electronics. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mean-variance portfolio analysis data for optimizing community-based photovoltaic investment.

PubMed

Shakouri, Mahmoud; Lee, Hyun Woo

2016-03-01

The amount of electricity generated by Photovoltaic (PV) systems is affected by factors such as shading, building orientation and roof slope. To increase electricity generation and reduce volatility in generation of PV systems, a portfolio of PV systems can be made which takes advantages of the potential synergy among neighboring buildings. This paper contains data supporting the research article entitled: PACPIM: new decision-support model of optimized portfolio analysis for community-based photovoltaic investment [1]. We present a set of data relating to physical properties of 24 houses in Oregon, USA, along with simulated hourly electricity data for the installed PV systems. The developed Matlab code to construct optimized portfolios is also provided in . The application of these files can be generalized to variety of communities interested in investing on PV systems.

Application experience with the NASA aircraft interrogation and display system - A ground-support equipment for digital flight systems

NASA Technical Reports Server (NTRS)

Glover, R. D.

1983-01-01

The NASA Dryden Flight Research Facility has developed a microprocessor-based, user-programmable, general-purpose aircraft interrogation and display system (AIDS). The hardware and software of this ground-support equipment have been designed to permit diverse applications in support of aircraft digital flight-control systems and simulation facilities. AIDS is often employed to provide engineering-units display of internal digital system parameters during development and qualification testing. Such visibility into the system under test has proved to be a key element in the final qualification testing of aircraft digital flight-control systems. Three first-generation 8-bit units are now in service in support of several research aircraft projects, and user acceptance has been high. A second-generation design, extended AIDS (XAIDS), incorporating multiple 16-bit processors, is now being developed to support the forward swept wing aircraft project (X-29A). This paper outlines the AIDS concept, summarizes AIDS operational experience, and describes the planned XAIDS design and mechanization.

Flight evaluation of a computer aided low-altitude helicopter flight guidance system

NASA Technical Reports Server (NTRS)

Swenson, Harry N.; Jones, Raymond D.; Clark, Raymond

1993-01-01

The Flight Systems Development branch of the U.S. Army's Avionics Research and Development Activity (AVRADA) and NASA Ames Research Center developed for flight testing a Computer Aided Low-Altitude Helicopter Flight (CALAHF) guidance system. The system includes a trajectory-generation algorithm which uses dynamic programming and a helmet-mounted display (HMD) presentation of a pathway-in-the-sky, a phantom aircraft, and flight-path vector/predictor guidance symbology. The trajectory-generation algorithm uses knowledge of the global mission requirements, a digital terrain map, aircraft performance capabilities, and precision navigation information to determine a trajectory between mission waypoints that seeks valleys to minimize threat exposure. This system was developed and evaluated through extensive use of piloted simulation and has demonstrated a 'pilot centered' concept of automated and integrated navigation and terrain mission planning flight guidance. This system has shown a significant improvement in pilot situational awareness, and mission effectiveness as well as a decrease in training and proficiency time required for a near terrain, nighttime, adverse weather system.

Test Program for Stirling Radioisotope Generator Hardware at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Lewandowski, Edward J.; Bolotin, Gary S.; Oriti, Salvatore M.

2015-01-01

Stirling-based energy conversion technology has demonstrated the potential of high efficiency and low mass power systems for future space missions. This capability is beneficial, if not essential, to making certain deep space missions possible. Significant progress was made developing the Advanced Stirling Radioisotope Generator (ASRG), a 140-W radioisotope power system. A variety of flight-like hardware, including Stirling convertors, controllers, and housings, was designed and built under the ASRG flight development project. To support future Stirling-based power system development NASA has proposals that, if funded, will allow this hardware to go on test at the NASA Glenn Research Center. While future flight hardware may not be identical to the hardware developed under the ASRG flight development project, many components will likely be similar, and system architectures may have heritage to ASRG. Thus, the importance of testing the ASRG hardware to the development of future Stirling-based power systems cannot be understated. This proposed testing will include performance testing, extended operation to establish an extensive reliability database, and characterization testing to quantify subsystem and system performance and better understand system interfaces. This paper details this proposed test program for Stirling radioisotope generator hardware at NASA Glenn. It explains the rationale behind the proposed tests and how these tests will meet the stated objectives.

Test Program for Stirling Radioisotope Generator Hardware at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Lewandowski, Edward J.; Bolotin, Gary S.; Oriti, Salvatore M.

2014-01-01

Stirling-based energy conversion technology has demonstrated the potential of high efficiency and low mass power systems for future space missions. This capability is beneficial, if not essential, to making certain deep space missions possible. Significant progress was made developing the Advanced Stirling Radioisotope Generator (ASRG), a 140-watt radioisotope power system. A variety of flight-like hardware, including Stirling convertors, controllers, and housings, was designed and built under the ASRG flight development project. To support future Stirling-based power system development NASA has proposals that, if funded, will allow this hardware to go on test at the NASA Glenn Research Center (GRC). While future flight hardware may not be identical to the hardware developed under the ASRG flight development project, many components will likely be similar, and system architectures may have heritage to ASRG. Thus the importance of testing the ASRG hardware to the development of future Stirling-based power systems cannot be understated. This proposed testing will include performance testing, extended operation to establish an extensive reliability database, and characterization testing to quantify subsystem and system performance and better understand system interfaces. This paper details this proposed test program for Stirling radioisotope generator hardware at NASA GRC. It explains the rationale behind the proposed tests and how these tests will meet the stated objectives.

FAIRDOMHub: a repository and collaboration environment for sharing systems biology research.

PubMed

Wolstencroft, Katherine; Krebs, Olga; Snoep, Jacky L; Stanford, Natalie J; Bacall, Finn; Golebiewski, Martin; Kuzyakiv, Rostyk; Nguyen, Quyen; Owen, Stuart; Soiland-Reyes, Stian; Straszewski, Jakub; van Niekerk, David D; Williams, Alan R; Malmström, Lars; Rinn, Bernd; Müller, Wolfgang; Goble, Carole

2017-01-04

The FAIRDOMHub is a repository for publishing FAIR (Findable, Accessible, Interoperable and Reusable) Data, Operating procedures and Models (https://fairdomhub.org/) for the Systems Biology community. It is a web-accessible repository for storing and sharing systems biology research assets. It enables researchers to organize, share and publish data, models and protocols, interlink them in the context of the systems biology investigations that produced them, and to interrogate them via API interfaces. By using the FAIRDOMHub, researchers can achieve more effective exchange with geographically distributed collaborators during projects, ensure results are sustained and preserved and generate reproducible publications that adhere to the FAIR guiding principles of data stewardship. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Past, present and future of cyanide antagonism research: From the early remedies to the current therapies.

PubMed

Petrikovics, Ilona; Budai, Marianna; Kovacs, Kristof; Thompson, David E

2015-06-26

This paper reviews milestones in antidotal therapies for cyanide (CN) spanning early remedies, current antidotal systems and research towards next generation therapies. CN has been a part of plant defense mechanisms for millions of years. It became industrially important in the nineteenth century with the advent of CN assisted gold mining and the use of CN as a pest control agent. The biochemical basis of CN poisoning was actively studied and key mechanisms were understood as early as 1929. These fundamental studies led to a variety of antidotes, including indirect CN binders that generate methemoglobin, direct CN binders such as hydroxocobalamin, and sulfur donors that convert CN to the less toxic thiocyanate. Research on blood gases at the end of the twentieth century shed new light on the role of nitric oxide (NO) in the body. The discovery of NO's ability to compete with CN for enzymatic binding sites provided a previously missed explanation for the rapid efficacy of NO generating antidotes such as the nitrites. Presently used CN therapies include: methemoglobin/NO generators (e.g., sodium nitrite, amyl nitrite, and dimethyl aminophenol), sulfur donors (e.g., sodium thiosulfate and glutathione), and direct binding agents [(e.g., hydroxocobalamin and dicobalt salt of ethylenediaminetetraacetic acid (dicobalt edetate)]. A strong effort is being made to explore novel antidotal systems and to formulate them for rapid administration at the point of intoxication in mass casualty scenarios. New antidotes, formulations, and delivery systems are enhancing bioavailability and efficacy and hold promise for a new generation of improved CN countermeasures.

W.a.w (we are watching) smart app: accommodating social perception towards public officers’ performance

NASA Astrophysics Data System (ADS)

Widhoyoko, S. A.; Sasmoko; Nasir, L. A.; Manalu, S. R.; Indrianti, Y.

2018-03-01

This research is a continuation of previous research that is corruption early prevention is expanded by using expert system to analyze data and produce information to build decision. The research method used is neuroresearch method through three stages of research, namely exploratory stage, explanatory stage and confirmatory stages. The exploratory research finds W.aW’s Principles and W.a.W’s Units of Assessment as the basis for the preparation of the application. Stages of explanatory research in the form of W.a.W’s design of IT and confirmatory research stages are the design of expert system W.a.W. Expert System uses this formulation to generate dynamic standard value for each category and current social perception.

Construction of In-house Databases in a Corporation

NASA Astrophysics Data System (ADS)

Fujii, Yohzo

The author outlines the inhouse technical information system, OSTI of Osaka Research Institute, Sumitomo Chemical company as an example of inhouse database construction and use at a chemical industry. This system is to compile database for technical information generated inside the Laboratory and to provide online searching as well as title lists of the latest data output from it aiming at effective use of information among the departments, prevention from overlapped research thema, and support of research activities. The system outline, characteristics, materials to be covered, input items and search examples are described.

A database for propagation models

NASA Technical Reports Server (NTRS)

Kantak, Anil V.; Suwitra, Krisjani; Le, Choung

1993-01-01

The NASA Propagation Program supports academic research that models various propagation phenomena in the space research frequency bands. NASA supports such research via school and institutions prominent in the field. The products of such efforts are particularly useful for researchers in the field of propagation phenomena and telecommunications systems engineers. The systems engineer usually needs a few propagation parameter values for a system design. Published literature on the subject, such as the Cunsultative Committee for International Radio (CCIR) publications, may help somewhat, but often times, the parameter values given in such publications use a particular set of conditions which may not quite include the requirements of the system design. The systems engineer must resort to programming the propagation phenomena model of interest and to obtain the parameter values to be used in the project. Furthermore, the researcher in the propagation field must then program the propagation models either to substantiate the model or to generate a new model. The researcher or the systems engineer must either be a skillful computer programmer or hire a programmer, which of course increases the cost of the effort. An increase in cost due to the inevitable programming effort may seem particularly inappropriate if the data generated by the experiment is to be used to substantiate the already well-established models, or a slight variation thereof. To help researchers and the systems engineers, it was recommended by the participants of NASA Propagation Experimenters (NAPEX) 15 held in London, Ontario, Canada on 28-29 June 1991, that propagation software should be constructed which will contain models and prediction methods of most propagation phenomenon. Moreover, the software should be flexible enough for the user to make slight changes to the models without expending a substantial effort in programming.

Using Generative Representations to Evolve Robots. Chapter 1

NASA Technical Reports Server (NTRS)

Hornby, Gregory S.

2004-01-01

Recent research has demonstrated the ability of evolutionary algorithms to automatically design both the physical structure and software controller of real physical robots. One of the challenges for these automated design systems is to improve their ability to scale to the high complexities found in real-world problems. Here we claim that for automated design systems to scale in complexity they must use a representation which allows for the hierarchical creation and reuse of modules, which we call a generative representation. Not only is the ability to reuse modules necessary for functional scalability, but it is also valuable for improving efficiency in testing and construction. We then describe an evolutionary design system with a generative representation capable of hierarchical modularity and demonstrate it for the design of locomoting robots in simulation. Finally, results from our experiments show that evolution with our generative representation produces better robots than those evolved with a non-generative representation.

Development of an integrated transuranic waste management system for a large research facility: NUCEF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mineo, Hideaki; Matsumura, Tatsuro; Takeshita, Isao

1997-03-01

The Nuclear Fuel Cycle Safety Engineering Research Facility (NUCEF) is a large complex of research facilities where transuranic (TRU) elements are used. Liquid and solid waste containing TRU elements is generated mainly in the treatment of fuel for critical experiments and in the research of reprocessing and TRU waste management in hot cells and glove boxes. The rational management of TRU wastes is a very important issue not only for NUCEF but also for Japan. An integrated TRU waste management system is being developed with NUCEF as the test bed. The basic policy for establishing the system is to classifymore » wastes by TRU concentration, to reduce waste volume, and to maximize reuse of TRU elements. The principal approach of the development program is to apply the outcomes of the research carried out in NUCEF. Key technologies are TRU measurement for classification of solid wastes and TRU separation and volume reduction for organic and aqueous wastes. Some technologies required for treating the wastes specific to the research activities in NUCEF need further development. Specifically, the separation and stabilization technologies for americium recovery from concentrated aqueous waste, which is generated in dissolution of mixed oxide when preparing fuel for critical experiments, needs further research.« less

DAPHNE: Energy Generation and storage, using Solar Sails

NASA Astrophysics Data System (ADS)

Argelagós Palau, Ana Maria; Savio Bradford, Brandon

Space travel is still in it's adolescent stages. Having embarked beyond the limit of our atmosphere for a mere 50 years, it is easy to imagine how much is yet to be discovered, in other solar systems and our own. One of the main factors that slow us down is the need for Energy. Long distance space travel requires a lot of energy, both for propulsion and operations alike. The principle of solar sails shows that the momentum of solar energy can be used beneficially, as can be seen in NASA's Sun-Jammer project. So, why not generate energy from this system? The DAPHNE system will utilize the simple principle of wind mills that is used here on Earth; using the force created by Solar wind to rotate an axle that in turn, generates energy. And this mill can be used to recharge spacecraft that need to fly further than it's own initial energy system will allow. Another benefit to developing this system is the fact that it is an alternative to nuclear energy generation for space, that a lot of modern research is being done on. The DAPHNE system can be considered a solution to long term propellant storage in space for interplanetary and interstellar travel. This paper proposes the design of an energy recharge technology, we called DAPHNE, which will utilize Nanotechnology, using solar sails to generate and store energy for future long-distance space craft to dock with, recharge and continue on their journey/mission. Examples of spacecraft in development that might benefit from a recharging station are the LISA Pathfinder, terrestrial exploration missions and eventually, the long interstellar missions that will be launched in the distant future. Thereby, allowing mankind to push the boundaries of our solar system and accelerate our ability to know what's out there. This technology would help the future generations of Space researchers move further than we can.

Present status of MHD research and development in Israel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Branover, H.; Lesin, S.

1994-12-31

As in the previous years the Israel MHD program is concentrating exclusively on Liquid Metal MHD (LMMHD). The main effort is the development of gravitational heavy metal power generation systems with a Faraday type generator (ETGAR-type system). However, in the wake of this main development a number of diverse research projects are also elaborated. Two of those projects are reflected in this paper. First is the direct contact boiling of volatile thermodynamic liquids in hot liquid metals and the second is MHD turbulence with a variety of applications. The LMMHD power generation project is now about to enter the stagemore » of building a semi-commercial scale demonstration plant. The concept and performance parameters of this plant have been presented already at SEAM 30. Direct contact boiling of the volatile liquid in a hot metal leads to a substantial decrease of the cost of a LMMHD power generation system. Indeed, in this case a separate boiler is not needed. Moreover, the overall efficiency of the system is increased through achieving a more desirable two-phase flow pattern. A Special integrated facility for this study is in advanced stage of assembly and it will be put in operation soon. It will work with lead and water at temperatures up to 750{degrees}K. In the field of MHD Turbulence research, studies of two applications are pursued. The first is related to the engineering of liquid metal blankets in thermonuclear reactors. The second is connected with a possibility to simulate large scale atmospheric and oceanic turbulence using a laboratory MHD channel with liquid metal flow.« less

Controls/CFD Interdisciplinary Research Software Generates Low-Order Linear Models for Control Design From Steady-State CFD Results

NASA Technical Reports Server (NTRS)

Melcher, Kevin J.

1997-01-01

The NASA Lewis Research Center is developing analytical methods and software tools to create a bridge between the controls and computational fluid dynamics (CFD) disciplines. Traditionally, control design engineers have used coarse nonlinear simulations to generate information for the design of new propulsion system controls. However, such traditional methods are not adequate for modeling the propulsion systems of complex, high-speed vehicles like the High Speed Civil Transport. To properly model the relevant flow physics of high-speed propulsion systems, one must use simulations based on CFD methods. Such CFD simulations have become useful tools for engineers that are designing propulsion system components. The analysis techniques and software being developed as part of this effort are an attempt to evolve CFD into a useful tool for control design as well. One major aspect of this research is the generation of linear models from steady-state CFD results. CFD simulations, often used during the design of high-speed inlets, yield high resolution operating point data. Under a NASA grant, the University of Akron has developed analytical techniques and software tools that use these data to generate linear models for control design. The resulting linear models have the same number of states as the original CFD simulation, so they are still very large and computationally cumbersome. Model reduction techniques have been successfully applied to reduce these large linear models by several orders of magnitude without significantly changing the dynamic response. The result is an accurate, easy to use, low-order linear model that takes less time to generate than those generated by traditional means. The development of methods for generating low-order linear models from steady-state CFD is most complete at the one-dimensional level, where software is available to generate models with different kinds of input and output variables. One-dimensional methods have been extended somewhat so that linear models can also be generated from two- and three-dimensional steady-state results. Standard techniques are adequate for reducing the order of one-dimensional CFD-based linear models. However, reduction of linear models based on two- and three-dimensional CFD results is complicated by very sparse, ill-conditioned matrices. Some novel approaches are being investigated to solve this problem.

Studies on Effective Utilization of SOFC Exhaust Heat Using Thermoelectric Power Generation Technology

NASA Astrophysics Data System (ADS)

Terayama, Takeshi; Nagata, Susumu; Tanaka, Yohei; Momma, Akihiko; Kato, Tohru; Kunii, Masaru; Yamamoto, Atsushi

2013-07-01

Solid oxide fuel cells (SOFCs) are being researched around the world. In Japan, a compact SOFC system with rated alternative current (AC) power of 700 W has become available on the market, since the base load electricity demand for a standard home is said to be less than 700 W AC. To improve the generating efficiency of SOFC systems in the 700-W class, we focused on thermoelectric generation (TEG) technology, since there are a lot of temperature gradients in the system. Analysis based on simulations indicated the possibility of introducing thermoelectric generation at the air preheater, steam generator, and exhaust outlet. Among these options, incorporating a TEG heat exchanger comprising multiple CoSb3/SiGe-based TEG modules into the air preheater had potential to produce additional output of 37.5 W and an improvement in generating efficiency from 46% to 48.5%. Furthermore, by introducing thermoelectric generation at the other two locations, an increase in maximum output of more than 50 W and generating efficiency of 50% can be anticipated.

Generating target system specifications from a domain model using CLIPS

NASA Technical Reports Server (NTRS)

Sugumaran, Vijayan; Gomaa, Hassan; Kerschberg, Larry

1991-01-01

The quest for reuse in software engineering is still being pursued and researchers are actively investigating the domain modeling approach to software construction. There are several domain modeling efforts reported in the literature and they all agree that the components that are generated from domain modeling are more conducive to reuse. Once a domain model is created, several target systems can be generated by tailoring the domain model or by evolving the domain model and then tailoring it according to the specified requirements. This paper presents the Evolutionary Domain Life Cycle (EDLC) paradigm in which a domain model is created using multiple views, namely, aggregation hierarchy, generalization/specialization hierarchies, object communication diagrams and state transition diagrams. The architecture of the Knowledge Based Requirements Elicitation Tool (KBRET) which is used to generate target system specifications is also presented. The preliminary version of KBRET is implemented in the C Language Integrated Production System (CLIPS).

Recognition of handprinted characters for automated cartography A progress report

NASA Technical Reports Server (NTRS)

Lybanon, M.; Brown, R. M.; Gronmeyer, L. K.

1980-01-01

A research program for developing handwritten character recognition techniques is reported. The generation of cartographic/hydrographic manuscripts is overviewed. The performance of hardware/software systems is discussed, along with future research problem areas and planned approaches.

Learning Generation: Fostering Innovation with Tomorrow's Teachers and Technology

ERIC Educational Resources Information Center

Aust, Ronald; Newberry, Brian; O'Brien, Joseph; Thomas, Jennifer

2005-01-01

We discuss the context, conception, implementation, and research used to refine and evaluate a systemic model for fostering technology integration in teacher education. The Learning Generation model identifies conditions where innovations for using technology emerge in small group dialogues. The model uses a multifaceted implementation with…

Application of circular consensus sequencing and network analysis to characterize the bovine IgG repertoire

USDA-ARS?s Scientific Manuscript database

Background: Vertebrate immune systems generate diverse repertoires of antibodies capable of mediating response to a variety of antigens. Next generation sequencing methods provide unique approaches to a number of immuno-based research areas including antibody discovery and engineering, disease surve...

Interactive Model-Centric Systems Engineering (IMCSE) Phase 5

DTIC Science & Technology

2018-02-28

Conducting Program Team Launches ................................................................................................. 12 Informing Policy...research advances knowledge relevant to human interaction with models and model-generated information . Figure 1 highlights several questions the...stakeholders interact using models and model generated information ; facets of human interaction with visualizations and large data sets; and underlying

Fabricating Synthetic Data in Support of Training for Domestic Terrorist Activity Data Mining Research

DTIC Science & Technology

2010-09-01

of Mannheim seeks to produce realistic digital images for student analysis ( Moch & Freiling, 2009). Using instructor generated scripts and the...laboratory. ACM Transactions on Information and System Security, (pp. 262-294). Moch , C., & Freiling, F. (2009). The forensic image generator

Forced-flow once-through boilers. [structural design criteria/aerospace environments

NASA Technical Reports Server (NTRS)

Stone, J. R.; Gray, V. H.; Gutierrez, O. A.

1975-01-01

A compilation and review of NASA-sponsored research on boilers for use in spacecraft electrical power generation systems is presented. Emphasis is on the heat-transfer and fluid-flow problems. In addition to space applications, much of the boiler technology is applicable to terrestrial and marine uses such as vehicular power, electrical power generation, vapor generation, and heating and cooling. Related research areas are discussed such as condensation, cavitation, line and boiler dynamics, the SNAP-8 project (Mercury-Rankine cycle), and conventional terrestrial boilers (either supercritical or gravity-assisted liquid-vapor separation types). The research effort was directed at developing the technology for once-through compact boilers with high heat fluxes to generate dry vapor stably, without utilizing gravity for phase separations. A background section that discusses, tutorially, the complex aspects of the boiling process is presented. Discussions of tests on alkali metals are interspersed with those on water and other fluids on a phenomenological basis.

NOAA/NOS coastal and ocean assessment GIS: Initial application to environmental sensitivity index data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Monaco, M.E.; Battista, T.A.; Gill, T.A.

1997-06-01

NOAA`s National Ocean Service (NOS) is developing a suite of desktop geographic information system (GIS) tools to define, assess, and solve coastal resource management issues. This paper describes one component of the emerging NOS Coastal and Ocean Assessment GIS: Environmental Sensitivity Index (ESI) data with emphasis on living marine resource information. This work is underway through a unique federal, state, and private-sector partnership. The desktop GIS is a versatile, user-friendly system designed to provide coastal managers with mapping and analysis capabilities. These functions are under development using the recently generated North Carolina ESI data, with emphasis on accessing, analyzing, andmore » mapping estuarine species distributions. Example system features include: a user-friendly front end, generation of ESI maps and tables, and custom spatial and temporal analyses. Partners in the development of the desktop system include: NOAA`s Office of Ocean Resources Conservation and Assessment (ORCA) and Coastal Services Center, the Minerals Management Service (MMS), Florida Marine Research Institute, Environmental Systems Research Institute, Inc., and Research Planning, Inc. This work complements and supports MMS`s Gulf-wide Information System designed to support oil-spill contingency planning.« less

[Research consortium Neuroimmunology and pain in the research network musculoskeletal diseases].

PubMed

Schaible, H-G; Chang, H-D; Grässel, S; Haibel, H; Hess, A; Kamradt, T; Radbruch, A; Schett, G; Stein, C; Straub, R H

2018-05-01

The research consortium Neuroimmunology and Pain (Neuroimpa) explores the importance of the relationships between the immune system and the nervous system in musculoskeletal diseases for the generation of pain and for the course of fracture healing and arthritis. The spectrum of methods includes analyses at the single cell level, in vivo models of arthritis and fracture healing, imaging studies on brain function in animals and humans and analysis of data from patients. Proinflammatory cytokines significantly contribute to the generation of joint pain through neuronal cytokine receptors. Immune cells release opioid peptides which activate opioid receptors at peripheral nociceptors and thereby evoke hypoalgesia. The formation of new bone after fractures is significantly supported by the nervous system. The sympathetic nervous system promotes the development of immune-mediated arthritis. The studies show a significant analgesic potential of the neutralization of proinflammatory cytokines and of opioids which selectively inhibit peripheral neurons. Furthermore, they show that the modulation of neuronal mechanisms can beneficially influence the course of musculoskeletal diseases. Interventions in the interactions between the immune system and the nervous system hold a great therapeutic potential for the treatment of musculoskeletal diseases and pain.

An Overview and Status of NASA's Radioisotope Power Conversion Technology NRA

NASA Technical Reports Server (NTRS)

Anderson, David J.; Wong, Wayne A.; Tuttle, Karen L.

2005-01-01

NASA's Advanced Radioisotope Power Systems (RPS) development program is developing next generation radioisotope power conversion technologies that will enable future missions that have requirements that can not be met by either photovoltaic systems or by current Radioisotope Power System (RPS) technology. The Advanced Power Conversion Research and Technology project of the Advanced RPS development program is funding research and technology activities through the NASA Research Announcement (NRA) 02- OSS-01, "Research Opportunities in Space Science 2002" entitled "Radioisotope Power Conversion Technology" (RPCT), 13 August 2002. The objective of the RPCT NRA is to advance the development of radioisotope power conversion technologies to provide significant improvements over the state-of-practice General Purpose Heat Source/Radioisotope Thermoelectric Generator by providing significantly higher efficiency to reduce the number of radioisotope fuel modules, and increase specific power (watts/kilogram). Other Advanced RPS goals include safety, long-life, reliability, scalability, multi-mission capability, resistance to radiation, and minimal interference with the scientific payload. These advances would enable a factor of 2 to 4 decrease in the amount of fuel required to generate electrical power. The RPCT NRA selected advanced RPS power conversion technology research and development proposals in the following three areas: innovative RPS power conversion research, RPS power conversion technology development in a nominal 100We scale; and, milliwatt/multi-watt RPS (mWRPS) power conversion research. Ten RPCT NRA contracts were awarded in 2003 in the areas of Brayton, Stirling, thermoelectric (TE), and thermophotovoltaic (TPV) power conversion technologies. This paper will provide an overview of the RPCT NRA, and a brief summary of accomplishments over the first 18 months but focusing on advancements made over the last 6 months.

Next-generation mammalian genetics toward organism-level systems biology.

PubMed

Susaki, Etsuo A; Ukai, Hideki; Ueda, Hiroki R

2017-01-01

Organism-level systems biology in mammals aims to identify, analyze, control, and design molecular and cellular networks executing various biological functions in mammals. In particular, system-level identification and analysis of molecular and cellular networks can be accelerated by next-generation mammalian genetics. Mammalian genetics without crossing, where all production and phenotyping studies of genome-edited animals are completed within a single generation drastically reduce the time, space, and effort of conducting the systems research. Next-generation mammalian genetics is based on recent technological advancements in genome editing and developmental engineering. The process begins with introduction of double-strand breaks into genomic DNA by using site-specific endonucleases, which results in highly efficient genome editing in mammalian zygotes or embryonic stem cells. By using nuclease-mediated genome editing in zygotes, or ~100% embryonic stem cell-derived mouse technology, whole-body knock-out and knock-in mice can be produced within a single generation. These emerging technologies allow us to produce multiple knock-out or knock-in strains in high-throughput manner. In this review, we discuss the basic concepts and related technologies as well as current challenges and future opportunities for next-generation mammalian genetics in organism-level systems biology.

Water Waves Generated by a Slowly Moving Two-Dimensional Body. Part 2.

DTIC Science & Technology

1982-05-01

Francis Ogilvie This research was carried out under the sPonsorship of the Naval Sea Systems Command General Hydromechanics Research (GHR) Program under...from Report) IS. SUPPLEMENTARY NOTES Sponsored by Naval Sea Systems Command General Hydromechanics Research Program, administered by the David W. Taylor...asymptotically ff 0 k . If the domain of x is - ’ x ’ + , tite only part of the d.;ymy ., t< expansion that represents waves comes fr m the iitemoqeneous

openBIS: a flexible framework for managing and analyzing complex data in biology research

PubMed Central

2011-01-01

Background Modern data generation techniques used in distributed systems biology research projects often create datasets of enormous size and diversity. We argue that in order to overcome the challenge of managing those large quantitative datasets and maximise the biological information extracted from them, a sound information system is required. Ease of integration with data analysis pipelines and other computational tools is a key requirement for it. Results We have developed openBIS, an open source software framework for constructing user-friendly, scalable and powerful information systems for data and metadata acquired in biological experiments. openBIS enables users to collect, integrate, share, publish data and to connect to data processing pipelines. This framework can be extended and has been customized for different data types acquired by a range of technologies. Conclusions openBIS is currently being used by several SystemsX.ch and EU projects applying mass spectrometric measurements of metabolites and proteins, High Content Screening, or Next Generation Sequencing technologies. The attributes that make it interesting to a large research community involved in systems biology projects include versatility, simplicity in deployment, scalability to very large data, flexibility to handle any biological data type and extensibility to the needs of any research domain. PMID:22151573

New generation lidar systems for eye safe full time observations

NASA Technical Reports Server (NTRS)

Spinhirne, James D.

1995-01-01

The traditional lidar over the last thirty years has typically been a big pulse low repetition rate system. Pulse energies are in the 0.1 to 1.0 J range and repetition rates from 0.1 to 10 Hz. While such systems have proven to be good research tools, they have a number of limitations that prevent them from moving beyond lidar research to operational, application oriented instruments. These problems include a lack of eye safety, very low efficiency, poor reliability, lack of ruggedness and high development and operating costs. Recent advances in solid state laser, detectors and data systems have enabled the development of a new generation of lidar technology that meets the need for routine, application oriented instruments. In this paper the new approaches to operational lidar systems will be discussed. Micro pulse lidar (MPL) systems are currently in use, and their technology is highlighted. The basis and current development of continuous wave (CW) lidar and potential of other technical approaches is presented.

Piezoelectric, Solar and Thermal Energy Harvesting for Hybrid Low-Power Generator Systems With Thin-Film Batteries

DTIC Science & Technology

2012-01-01

research has investigated simultaneous harvesting of vibration energy using the direct piezoelectric effect and harvesting of magnetic energy (alternating... Piezoelectric , solar and thermal energy harvesting for hybrid low-power generator systems with thin-film batteries This article has been downloaded...TYPE 3. DATES COVERED 00-00-2011 to 00-00-2011 4. TITLE AND SUBTITLE Piezoelectric , solar and thermal energy harvesting for hybrid low-power

An airborne system for vortex flow visualization on the F-18 high-alpha research vehicle

NASA Technical Reports Server (NTRS)

Curry, Robert E.; Richwine, David M.

1988-01-01

A flow visualization system for the F-18 high-alpha research vehicle is described which allows direct observation of the separated vortex flows over a wide range of flight conditions. The system consists of a smoke generator system, on-board photographic and video systems, and instrumentation. In the present concept, smoke is entrained into the low-pressure vortex core, and vortice breakdown is indicated by a rapid diffusion of the smoke. The resulting pattern is observed using photographic and video images and is correlated with measured flight conditions.

Extended Durability Testing of an External Fuel Processor for a Solid Oxide Fuel Cell (SOFC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mark Perna; Anant Upadhyayula; Mark Scotto

2012-11-05

Durability testing was performed on an external fuel processor (EFP) for a solid oxide fuel cell (SOFC) power plant. The EFP enables the SOFC to reach high system efficiency (electrical efficiency up to 60%) using pipeline natural gas and eliminates the need for large quantities of bottled gases. LG Fuel Cell Systems Inc. (formerly known as Rolls-Royce Fuel Cell Systems (US) Inc.) (LGFCS) is developing natural gas-fired SOFC power plants for stationary power applications. These power plants will greatly benefit the public by reducing the cost of electricity while reducing the amount of gaseous emissions of carbon dioxide, sulfur oxides,more » and nitrogen oxides compared to conventional power plants. The EFP uses pipeline natural gas and air to provide all the gas streams required by the SOFC power plant; specifically those needed for start-up, normal operation, and shutdown. It includes a natural gas desulfurizer, a synthesis-gas generator and a start-gas generator. The research in this project demonstrated that the EFP could meet its performance and durability targets. The data generated helped assess the impact of long-term operation on system performance and system hardware. The research also showed the negative impact of ambient weather (both hot and cold conditions) on system operation and performance.« less

Waste-to-Energy Technology Brief

EPA Science Inventory

ETV's Greenhouse Gas Technology (GHG) Center, operated by Southern Research Institute under a cooperative agreement with US EPA, verified two biogas processing systems and four distributed generation (DG) energy systems in collaboration with the Colorado Governors Office or the N...

Second generation precast deck panel (NUDECK) system.

DOT National Transportation Integrated Search

2010-12-01

"The majority of todays bridge decks are built using cast-in-place concrete construction. This is due to the perceived : low initial cost and constructor familiarity with the system. This research report describes the design, details, and : constr...

Second generation precast deck panel (NUDECK) system.

DOT National Transportation Integrated Search

2010-12-01

The majority of today's bridge decks are built using cast-in-place concrete construction. This is due to the perceived : low initial cost and constructor familiarity with the system. This research report describes the design, details, and : construct...

Prospective communications research to support fly by light/power by wire

NASA Technical Reports Server (NTRS)

Game, David

1994-01-01

A NASA Research Grant NAG-1-1309, Distributed Fiber Optic Systems for Commercial Aircraft, was awarded during July 1991. This report primarily constitutes a summary of findings of the original background research done at that time. NASA is embarking on a research project to design the next generation of commercial aircraft, fly by light/power by wire. The objectives of this effort are to improve commercial aircraft design by (1) reducing the weight of the aircraft to improve efficiency and (2) improving the fault tolerance and safety of the aircraft by enhancing current systems with new technologies or introducing new systems into the aircraft.

Qualitative mechanism models and the rationalization of procedures

NASA Technical Reports Server (NTRS)

Farley, Arthur M.

1989-01-01

A qualitative, cluster-based approach to the representation of hydraulic systems is described and its potential for generating and explaining procedures is demonstrated. Many ideas are formalized and implemented as part of an interactive, computer-based system. The system allows for designing, displaying, and reasoning about hydraulic systems. The interactive system has an interface consisting of three windows: a design/control window, a cluster window, and a diagnosis/plan window. A qualitative mechanism model for the ORS (Orbital Refueling System) is presented to coordinate with ongoing research on this system being conducted at NASA Ames Research Center.

A Case Study of Wind-PV-Thermal-Bundled AC/DC Power Transmission from a Weak AC Network

NASA Astrophysics Data System (ADS)

Xiao, H. W.; Du, W. J.; Wang, H. F.; Song, Y. T.; Wang, Q.; Ding, J.; Chen, D. Z.; Wei, W.

2017-05-01

Wind power generation and photovoltaic (PV) power generation bundled with the support by conventional thermal generation enables the generation controllable and more suitable for being sent over to remote load centre which are beneficial for the stability of weak sending end systems. Meanwhile, HVDC for long-distance power transmission is of many significant technique advantages. Hence the effects of wind-PV-thermal-bundled power transmission by AC/DC on power system have become an actively pursued research subject recently. Firstly, this paper introduces the technical merits and difficulties of wind-photovoltaic-thermal bundled power transmission by AC/DC systems in terms of meeting the requirement of large-scale renewable power transmission. Secondly, a system model which contains a weak wind-PV-thermal-bundled sending end system and a receiving end system in together with a parallel AC/DC interconnection transmission system is established. Finally, the significant impacts of several factors which includes the power transmission ratio between the DC and AC line, the distance between the sending end system and receiving end system, the penetration rate of wind power and the sending end system structure on system stability are studied.

Robust distant-entanglement generation using coherent multiphoton scattering

NASA Astrophysics Data System (ADS)

Chan, Ching-Kit; Sham, L. J.

2013-03-01

The generation and controllability of entanglement between distant quantum states have been the heart of quantum computation and quantum information processing. Existing schemes for solid state qubit entanglement are based on the single-photon spectroscopy that has the merit of a high fidelity entanglement creation, but with a very limited efficiency. This severely restricts the scalability for a qubit network system. Here, we describe a new distant entanglement protocol using coherent multiphoton scattering. The scheme makes use of the postselection of large and distinguishable photon signals, and has both a high success probability and a high entanglement fidelity. Our result shows that the entanglement generation is robust against photon fluctuations, and has an average entanglement duration within the decoherence time in various qubit systems, based on existing experimental parameters. This research was supported by the U.S. Army Research Office MURI award W911NF0910406 and by NSF grant PHY-1104446.

Optimizing Decision Preparedness by Adapting Scenario Complexity and Automating Scenario Generation

NASA Technical Reports Server (NTRS)

Dunne, Rob; Schatz, Sae; Flore, Stephen M.; Nicholson, Denise

2011-01-01

Klein's recognition-primed decision (RPD) framework proposes that experts make decisions by recognizing similarities between current decision situations and previous decision experiences. Unfortunately, military personnel arQ often presented with situations that they have not experienced before. Scenario-based training (S8T) can help mitigate this gap. However, SBT remains a challenging and inefficient training approach. To address these limitations, the authors present an innovative formulation of scenario complexity that contributes to the larger research goal of developing an automated scenario generation system. This system will enable trainees to effectively advance through a variety of increasingly complex decision situations and experiences. By adapting scenario complexities and automating generation, trainees will be provided with a greater variety of appropriately calibrated training events, thus broadening their repositories of experience. Preliminary results from empirical testing (N=24) of the proof-of-concept formula are presented, and future avenues of scenario complexity research are also discussed.

Integrating Public Health Policy, Practice, Evaluation, Surveillance, and Research: The School Health Action Planning and Evaluation System

PubMed Central

Cameron, Roy; Manske, Stephen; Brown, K. Stephen; Jolin, Mari Alice; Murnaghan, Donna; Lovato, Chris

2007-01-01

The Canadian Cancer Society and the National Cancer Institute of Canada have charged their Centre for Behavioral Research and Program Evaluation with contributing to the development of the country’s systemic capacity to link research, policy, and practice related to population-level interventions. Local data collection and feedback systems are integral to this capacity. Canada’s School Health Action Planning and Evaluation System (SHAPES) allows data to be collected from all of a school’s students, and these data are used to produce computer-generated school “health profiles.” SHAPES is being used for intervention planning, evaluation, surveillance, and research across Canada. Strong demand and multipartner investment suggest that SHAPES is adding value in all of these domains. Such systems can contribute substantially to evidence-informed public health practice, public engagement, participatory action research, and relevant, timely population intervention research. PMID:17329662

DEMONSTRATION BULLETIN: RADIO FREQUENCY HEATING - IIT RESEARCH INSTITUTE

EPA Science Inventory

Radio frequency heating (RFH) is a process that uses electromagnetic energy generated by radio waves to heat soil in situ, thereby potentially enhancing the performance of standard soil vapor extraction (SVE) technologies. An RFH system developed by the IIT Research Institute ...

Transforming Education by Using a New Generation of Information Systems

ERIC Educational Resources Information Center

González-Sancho, Carlos; Vincent-Lancrin, Stéphan

2016-01-01

Data use is becoming a prominent strategy for educational innovation and improvement across countries. However, the fragmentation of data collection often hinders the capacity of policymakers, researchers and practitioners to access and analyse the wealth of data routinely generated in educational institutions. A critical step towards realising…

Preliminary design features of the RASCAL - A NASA/Army rotorcraft in-flight simulator

NASA Technical Reports Server (NTRS)

Aiken, Edwin W.; Jacobsen, Robert A.; Eshow, Michelle M.; Hindson, William S.; Doane, Douglas H.

1992-01-01

Salient design features of a new NASA/Army research rotorcraft - the Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) - are described. Using a UH-60A Black Hawk helicopter as a baseline vehicle, the RASCAL will be a flying laboratory capable of supporting the research requirements of major NASA and Army guidance, control, and display research programs. The paper describes the research facility requirements of these programs together with other critical constraints on the design of the research system, including safety-of-flight. Research program schedules demand a phased development approach, wherein specific research capability milestones are met and flight research projects are flown throughout the complete development cycle of the RASCAL. This development approach is summarized, and selected features of the research system are described. The research system includes a full-authority, programmable, fault-tolerant/fail-safe, fly-by-wire flight control system and a real-time obstacle detection and avoidance system which will generate low-latitude guidance commands to the pilot on a wide field-of-view, color helmet-mounted display.

Preliminary design features of the RASCAL: A NASA /Army rotorcraft in-flight simulator

NASA Technical Reports Server (NTRS)

Aiken, Edwin W.; Jacobsen, Robert A.; Eshow, Michelle M.; Hindson, William S.; Doane, Douglas H.

1993-01-01

Salient design features of a new NASA/Army research rotorcraft - the Rotorcraft-Aircrew Systems Concepts Airborne Laboratory (RASCAL) - are described. Using a UH-60A Black Hawk helicopter as a baseline vehicle, the RASCAL will be a flying laboratory capable of supporting the research requirements of major NASA and Army guidance, control, and display research programs. The paper describes the research facility requirements of these programs together with other critical constraints on the design of the research system, including safety-of-flight. Research program schedules demand a phased development approach, wherein specific research capability milestones are met and flight research projects are flown throughout the complete development cycle of the RASCAL. This development approach is summarized, and selected features of the research system are described. The research system includes a full-authority, programmable, fault-tolerant/fail-safe, fly-by-wire flight control system and a real-time obstacle detection and avoidance system which will generate low-altitude guidance commands to the pilot on a wide field-of-view, color helmet-mounted display.

Large-scale-system effectiveness analysis. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patton, A.D.; Ayoub, A.K.; Foster, J.W.

1979-11-01

Objective of the research project has been the investigation and development of methods for calculating system reliability indices which have absolute, and measurable, significance to consumers. Such indices are a necessary prerequisite to any scheme for system optimization which includes the economic consequences of consumer service interruptions. A further area of investigation has been joint consideration of generation and transmission in reliability studies. Methods for finding or estimating the probability distributions of some measures of reliability performance have been developed. The application of modern Monte Carlo simulation methods to compute reliability indices in generating systems has been studied.

Systems Medicine 2.0: Potential Benefits of Combining Electronic Health Care Records With Systems Science Models

PubMed Central

Gibson, Alexander R; Scott, Gregory; Harrison, Oliver; Dominiczak, Anna; Hanlon, Phil

2015-01-01

Background The global burden of disease is increasingly dominated by non-communicable diseases.These diseases are less amenable to curative and preventative interventions than communicable disease. This presents a challenge to medical practice and medical research, both of which are experiencing diminishing returns from increasing investment. Objective Our aim was to (1) review how medical knowledge is generated, and its limitations, (2) assess the potential for emerging technologies and ideas to improve medical research, and (3) suggest solutions and recommendations to increase medical research efficiency on non-communicable diseases. Methods We undertook an unsystematic review of peer-reviewed literature and technology websites. Results Our review generated the following conclusions and recommendations. (1) Medical knowledge continues to be generated in a reductionist paradigm. This oversimplifies our models of disease, rendering them ineffective to sufficiently understand the complex nature of non-communicable diseases. (2) Some of these failings may be overcome by adopting a “Systems Medicine” paradigm, where the human body is modeled as a complex adaptive system. That is, a system with multiple components and levels interacting in complex ways, wherein disease emerges from slow changes to the system set-up. Pursuing systems medicine research will require larger datasets. (3) Increased data sharing between researchers, patients, and clinicians could provide this unmet need for data. The recent emergence of electronic health care records (EHR) could potentially facilitate this in real-time and at a global level. (4) Efforts should continue to aggregate anonymous EHR data into large interoperable data silos and release this to researchers. However, international collaboration, data linkage, and obtaining additional information from patients will remain challenging. (5) Efforts should also continue towards “Medicine 2.0”. Patients should be given access to their personal EHR data. Subsequently, online communities can give researchers the opportunity to ask patients for direct access to the patient’s EHR data and request additional study-specific information. However, selection bias towards patients who use Web 2.0 technology may be difficult to overcome. Conclusions Systems medicine, when combined with large-scale data sharing, has the potential to raise our understanding of non-communicable diseases, foster personalized medicine, and make substantial progress towards halting, curing, and preventing non-communicable diseases. Large-scale data amalgamation remains a core challenge and needs to be supported. A synthesis of “Medicine 2.0” and “Systems Science” concepts into “Systems Medicine 2.0” could take decades to materialize but holds much promise. PMID:25831125

Systems Medicine 2.0: potential benefits of combining electronic health care records with systems science models.

PubMed

Tillmann, Taavi; Gibson, Alexander R; Scott, Gregory; Harrison, Oliver; Dominiczak, Anna; Hanlon, Phil

2015-03-23

The global burden of disease is increasingly dominated by non-communicable diseases.These diseases are less amenable to curative and preventative interventions than communicable disease. This presents a challenge to medical practice and medical research, both of which are experiencing diminishing returns from increasing investment. Our aim was to (1) review how medical knowledge is generated, and its limitations, (2) assess the potential for emerging technologies and ideas to improve medical research, and (3) suggest solutions and recommendations to increase medical research efficiency on non-communicable diseases. We undertook an unsystematic review of peer-reviewed literature and technology websites. Our review generated the following conclusions and recommendations. (1) Medical knowledge continues to be generated in a reductionist paradigm. This oversimplifies our models of disease, rendering them ineffective to sufficiently understand the complex nature of non-communicable diseases. (2) Some of these failings may be overcome by adopting a "Systems Medicine" paradigm, where the human body is modeled as a complex adaptive system. That is, a system with multiple components and levels interacting in complex ways, wherein disease emerges from slow changes to the system set-up. Pursuing systems medicine research will require larger datasets. (3) Increased data sharing between researchers, patients, and clinicians could provide this unmet need for data. The recent emergence of electronic health care records (EHR) could potentially facilitate this in real-time and at a global level. (4) Efforts should continue to aggregate anonymous EHR data into large interoperable data silos and release this to researchers. However, international collaboration, data linkage, and obtaining additional information from patients will remain challenging. (5) Efforts should also continue towards "Medicine 2.0". Patients should be given access to their personal EHR data. Subsequently, online communities can give researchers the opportunity to ask patients for direct access to the patient's EHR data and request additional study-specific information. However, selection bias towards patients who use Web 2.0 technology may be difficult to overcome. Systems medicine, when combined with large-scale data sharing, has the potential to raise our understanding of non-communicable diseases, foster personalized medicine, and make substantial progress towards halting, curing, and preventing non-communicable diseases. Large-scale data amalgamation remains a core challenge and needs to be supported. A synthesis of "Medicine 2.0" and "Systems Science" concepts into "Systems Medicine 2.0" could take decades to materialize but holds much promise.

Developing Guidelines for Assessing Visual Analytics Environments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scholtz, Jean

2011-07-01

In this paper, we develop guidelines for evaluating visual analytic environments based on a synthesis of reviews for the entries to the 2009 Visual Analytics Science and Technology (VAST) Symposium Challenge and from a user study with professional intelligence analysts. By analyzing the 2009 VAST Challenge reviews we gained a better understanding of what is important to our reviewers, both visualization researchers and professional analysts. We also report on a small user study with professional analysts to determine the important factors that they use in evaluating visual analysis systems. We then looked at guidelines developed by researchers in various domainsmore » and synthesized these into an initial set for use by others in the community. In a second part of the user study, we looked at guidelines for a new aspect of visual analytic systems – the generation of reports. Future visual analytic systems have been challenged to help analysts generate their reports. In our study we worked with analysts to understand the criteria they used to evaluate the quality of analytic reports. We propose that this knowledge will be useful as researchers look at systems to automate some of the report generation.1 Based on these efforts, we produced some initial guidelines for evaluating visual analytic environment and for evaluation of analytic reports. It is important to understand that these guidelines are initial drafts and are limited in scope because of the type of tasks for which the visual analytic systems used in the studies in this paper were designed. More research and refinement is needed by the Visual Analytics Community to provide additional evaluation guidelines for different types of visual analytic environments.« less

Research on DC Micro-grid system of photovoltaic power generation

NASA Astrophysics Data System (ADS)

Zheng, Yiming; Wang, Xiaohui

2018-01-01

The use of energy has become a topic of concern, the demand of people for power grows in number or quantity with the development of economy. It is necessary to consider using new forms of power supply-microgrid system for distributed power supply. The power supply mode can not only effectively solve the problem of excessive line loss in the large power grid, but also can increase the reliability of the power supply, and is economical and environmental friendly. With the increasing of DC loads, in order to improve the utilization efficiency, the DC microgrid power supply problems are begin to be researched and integrated with the renewable energy sources. This paper researched the development of microgrid, compared AC microgrid with DC microgrid, summarized the distribution of DC bus voltage level, the DC microgrid network form, the control mode and the main power electronics elements of DC microgrid of photovoltaic power generation system. Today, the DC microgrid system is still in the development stage without uniform voltage level standard, however, it will come into service in the future.

Transient and Steady-state Tests of the Space Power Research Engine with Resistive and Motor Loads

NASA Technical Reports Server (NTRS)

Rauch, Jeffrey S.; Kankam, M. David

1995-01-01

The NASA Lewis Research Center (LeRC) has been testing free-piston Stirling engine/linear alternators (FPSE/LA) to develop advanced power convertors for space-based electrical power generation. Tests reported herein were performed to evaluate the interaction and transient behavior of FPSE/LA-based power systems with typical user loads. Both resistive and small induction motor loads were tested with the space power research engine (SPRE) power system. Tests showed that the control system could maintain constant long term voltage and stable periodic operation over a large range of engine operating parameters and loads. Modest resistive load changes were shown to cause relatively large voltage and, therefore, piston and displacer amplitude excursions. Starting a typical small induction motor was shown to cause large and, in some cases, deleterious voltage transients. The tests identified the need for more effective controls, if FPSE/LAs are to be used for stand-alone power systems. The tests also generated a large body of transient dynamic data useful for analysis code validation.

Transient and steady-state tests of the space power research engine with resistive and motor loads

NASA Astrophysics Data System (ADS)

Rauch, Jeffrey S.; Kankam, M. David

1995-01-01

The NASA Lewis Research Center (LeRC) has been testing free-piston Stirling engine/linear alternators (FPSE/LA) to develop advanced power convertors for space-based electrical power generation. Tests reported herein were performed to evaluate the interaction and transient behavior of FPSE/LA-based power systems with typical user loads. Both resistive and small induction motor loads were tested with the space power research engine (SPRE) power system. Tests showed that the control system could maintain constant long term voltage and stable periodic operation over a large range of engine operating parameters and loads. Modest resistive load changes were shown to cause relatively large voltage and, therefore, piston and displacer amplitude excursions. Starting a typical small induction motor was shown to cause large and, in some cases, deleterious voltage transients. The tests identified the need for more effective controls, if FPSE/LAs are to be used for stand-alone power systems. The tests also generated a large body of transient dynamic data useful for analysis code validation.

Mean-variance portfolio analysis data for optimizing community-based photovoltaic investment

PubMed Central

Shakouri, Mahmoud; Lee, Hyun Woo

2016-01-01

The amount of electricity generated by Photovoltaic (PV) systems is affected by factors such as shading, building orientation and roof slope. To increase electricity generation and reduce volatility in generation of PV systems, a portfolio of PV systems can be made which takes advantages of the potential synergy among neighboring buildings. This paper contains data supporting the research article entitled: PACPIM: new decision-support model of optimized portfolio analysis for community-based photovoltaic investment [1]. We present a set of data relating to physical properties of 24 houses in Oregon, USA, along with simulated hourly electricity data for the installed PV systems. The developed Matlab code to construct optimized portfolios is also provided in Supplementary materials. The application of these files can be generalized to variety of communities interested in investing on PV systems. PMID:26937458

NASA's Solar System Exploration Research Virtual Institute: Building Collaboration Through International Partnerships

NASA Technical Reports Server (NTRS)

Gibbs, K. E.; Schmidt, G. K.

2017-01-01

The NASA Solar System Exploration Research Virtual Institute (SSERVI) is a virtual institute focused on re-search at the intersection of science and exploration, training the next generation of lunar scientists, and community development. As part of the SSERVI mission, we act as a hub for opportunities that engage the larger scientific and exploration communities in order to form new interdisciplinary, research-focused collaborations. This talk will describe the international partner re-search efforts and how we are engaging the international science and exploration communities through workshops, conferences, online seminars and classes, student exchange programs and internships.

AFRC-2016-11157-1-NewAviationHorizons

NASA Image and Video Library

2016-02-01

NASA's Armstrong Flight Research Center conducts research to advance science, technology and aeronautics through flight. This video highlights some of the flight research and other activities that occurred at NASA Armstrong in 2015 in an effort to support of the agency's strategic goals in Earth science, space exploration, next-generation aviation systems and technology development.

Spray System Trials in the Icing Research Tunnel

NASA Image and Video Library

1949-09-21

The spray bar system introduces water droplets into the Icing Research Tunnel’s air stream at the National Advisory Committee for Aeronautics (NACA) Lewis Flight Propulsion Laboratory. The icing tunnel was designed in the early 1940s to study ice accretion on airfoils and models. The Carrier Corporation designed a refrigeration system that reduced temperatures to -45° F. The tunnel’s drive fan generated speeds up to 400 miles per hour. The uniform injection of water droplets to the air was a key element of the facility’s operation. The system had to generate small droplets, distribute them uniformly throughout the airstream, and resist freezing and blockage. The Icing Research Tunnel’s designers struggled to develop a realistic spray system because they did not have access to data on the size of naturally occurring water droplets. For five years a variety of different designs were painstakingly developed and tested before the system was perfected. This photograph shows one of the trials using eight air-atomizing nozzles placed 48 feet upstream from the test section. A multi-cylinder device measured the size, liquid content, and distribution of the water droplets. The final system that was put into operation in 1950 included six horizontal spray bars with 80 nozzles that produced a 4- by 4-foot cloud in the test section. The Icing Research Tunnel produced excellent data throughout the 1950s and provided the basis for a hot air anti-icing system used on many transport aircraft.

Preparation of TNT, RDX and Ammonium Nitrate Standards on Gold-on-Silicon Surfaces by Thermal Inkjet Technology

NASA Astrophysics Data System (ADS)

Wrable-Rose, Madeline; Primera-Pedrozo, Oliva M.; Pacheco-Londoño, Leonardo C.; Hernandez-Rivera, Samuel P.

2010-12-01

This research examines the surface contamination properties, trace sample preparation methodologies, detection systems response and generation of explosive contamination standards for trace detection systems. Homogeneous and reproducible sample preparation is relevant for trace detection of chemical threats, such as warfare agents, highly energetic materials (HEM) and toxic industrial chemicals. The objective of this research was to develop a technology capable of producing samples and standards of HEM with controlled size and distribution on a substrate to generate specimens that would reproduce real contamination conditions. The research activities included (1) a study of the properties of particles generated by two deposition techniques: sample smearing deposition and inkjet deposition, on gold-coated silicon, glass and stainless steel substrates; (2) characterization of composition, distribution and adhesion characteristics of deposits; (3) evaluation of accuracy and reproducibility for depositing neat highly energetic materials such as TNT, RDX and ammonium nitrate; (4) a study of HEM-surface interactions using FTIR-RAIRS; and (5) establishment of protocols for validation of surface concentration using destructive methods such as HPLC.

Computer-generated forces in distributed interactive simulation

NASA Astrophysics Data System (ADS)

Petty, Mikel D.

1995-04-01

Distributed Interactive Simulation (DIS) is an architecture for building large-scale simulation models from a set of independent simulator nodes communicating via a common network protocol. DIS is most often used to create a simulated battlefield for military training. Computer Generated Forces (CGF) systems control large numbers of autonomous battlefield entities in a DIS simulation using computer equipment and software rather than humans in simulators. CGF entities serve as both enemy forces and supplemental friendly forces in a DIS exercise. Research into various aspects of CGF systems is ongoing. Several CGF systems have been implemented.

Patient-Clinician Encounter Information Modeling Through Web Based Intelligent 3D Visual Interface

DTIC Science & Technology

2002-09-01

system must allow immediate access to the lab data without the need to abort the evaluation process), and (5) must apply visual thinking principles. It... Systems Research, Incorporated For a period of five (5) years after completion of the project from which the data was generated, the Government’s rights...Report 3 Sigma Systems Research, Inc. List of Figures FIGURE 1. THE TWO MAJOR ELEMENTS OF THE DEVELOPED MEDICAL DATA VISUALIZATION FRAMEWORK ..... 7

Thermophotovoltaic potential applications for civilian and industrial use in Japan

NASA Astrophysics Data System (ADS)

Yamaguchi, Hiromi; Yamaguchi, Masafumi

1999-03-01

Investigative research on potential market for TPV power sources in Japan has been focused on how TPV can contribute to energy conservation and environmental protection and harmony. The application needs for TPV were surveyed in comparison with conventional engine or turbine generators and developing power generation technologies such as fuel cells or chemical batteries, etc. The investigation on the performance of commercial generators shows that regarding system efficiency, TPV can compete with conventional generators in the output power class of tens of kW. According to the sales for small scale generators in Japan, most of the generators below 10 kW class are utilized mainly for construction, communication, leisure, and that 10-100 kW class generators are for cogeneration in small buildings. Waste heat recovery in dispersed furnaces is another potential application of compact TPV cells. Exhaust heat from small scale incinerators and industrial furnaces is undesirable to be recorded into electricity due to excessive heat loss of the smaller steam turbine generators. Solar powered TPV is also of our concern as a natural energy use. From the viewpoint of applicability for TPV, portable generators cogeneration systems, and solar power plants were selected for our system consideration. Intermediate report on the feasibility study concerning such TPV systems is given as well as the review of the current status of competing power generation technologies in Japan.

Complex of technologies and prototype systems for eco-friendly shutdown of the power-generating, process, capacitive, and transport equipment

NASA Astrophysics Data System (ADS)

Smorodin, A. I.; Red'kin, V. V.; Frolov, Y. D.; Korobkov, A. A.; Kemaev, O. V.; Kulik, M. V.; Shabalin, O. V.

2015-07-01

A set of technologies and prototype systems for eco-friendly shutdown of the power-generating, process, capacitive, and transport equipment is offered. The following technologies are regarded as core technologies for the complex: cryogenic technology nitrogen for displacement of hydrogen from the cooling circuit of turbine generators, cryo blasting of the power units by dioxide granules, preservation of the shutdown power units by dehydrated air, and dismantling and severing of equipment and structural materials of power units. Four prototype systems for eco-friendly shutdown of the power units may be built on the basis of selected technologies: Multimode nitrogen cryogenic system with four subsystems, cryo blasting system with CO2 granules for thermal-mechanical and electrical equipment of power units, and compressionless air-drainage systems for drying and storage of the shutdown power units and cryo-gas system for general severing of the steam-turbine power units. Results of the research and pilot and demonstration tests of the operational units of the considered technological systems allow applying the proposed technologies and systems in the prototype systems for shutdown of the power-generating, process, capacitive, and transport equipment.

Work Began on Contracts for Radioisotope Power Conversion Technology Research and Development

NASA Technical Reports Server (NTRS)

Wong, Wayne A.

2005-01-01

NASA has had a history of successful space flight missions that depended on radioisotope-fueled power systems. These Radioisotope Power Systems (RPSs) converted the heat generated from the decay of radioisotope material into useful electrical power. An RPS is most attractive in applications where photovoltaics are not optimal, such as deep-space applications where the solar flux is too low or extended applications on planets such as Mars where the day/night cycle, settling of dust, and life requirements limit the usefulness of photovoltaics. NASA s Radioisotope Power Conversion Technology (RPCT) Program is developing next-generation power-conversion technologies that will enable future missions that have requirements that cannot be met by the two RPS flight systems currently being developed by the Department of Energy for NASA: the Multi-Mission Radioisotope Thermoelectric Generator and the Stirling Radioisotope Generator (SRG).

WE-AB-BRB-12: Nanoscintillator Fiber-Optic Detector System for Microbeam Radiation Therapy Dosimetry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rivera, J; Dooley, J; Chang, S

2015-06-15

Purpose: Microbeam Radiation Therapy (MRT) is an experimental radiation therapy that has demonstrated a higher therapeutic ratio than conventional radiation therapy in animal studies. There are several roadblocks in translating the promising treatment technology to clinical application, one of which is the lack of a real-time, high-resolution dosimeter. Current clinical radiation detectors have poor spatial resolution and, as such, are unsuitable for measuring microbeams with submillimeter-scale widths. Although GafChromic film has high spatial resolution, it lacks the real-time dosimetry capability necessary for MRT preclinical research and potential clinical use. In this work we have demonstrated the feasibility of using amore » nanoscintillator fiber-optic detector (nanoFOD) system for real-time MRT dosimetry. Methods: A microplanar beam array is generated using a x-ray research irradiator and a custom-made, microbeam-forming collimator. The newest generation nanoFOD has an effective size of 70 µm in the measurement direction and was calibrated against a kV ion chamber (RadCal Accu-Pro) in open field geometry. We have written a computer script that performs automatic data collection with immediate background subtraction. A computer-controlled detector positioning stage is used to precisely measure the microbeam peak dose and beam profile by translating the stage during data collection. We test the new generation nanoFOD system, with increased active scintillation volume, against the previous generation system. Both raw and processed data are time-stamped and recorded to enable future post-processing. Results: The real-time microbeam dosimetry system worked as expected. The new generation dosimeter has approximately double the active volume compared to the previous generation resulting in over 900% increase in signal. The active volume of the dosimeter still provided the spatial resolution that meets the Nyquist criterion for our microbeam widths. Conclusion: We have demonstrated that real-time dosimetry of MRT microbeams is feasible using a nanoscintillator fiber-optic detector with integrated positioning system.« less

Understanding the use of standardized nursing terminology and classification systems in published research: A case study using the International Classification for Nursing Practice(®).

PubMed

Strudwick, Gillian; Hardiker, Nicholas R

2016-10-01

In the era of evidenced based healthcare, nursing is required to demonstrate that care provided by nurses is associated with optimal patient outcomes, and a high degree of quality and safety. The use of standardized nursing terminologies and classification systems are a way that nursing documentation can be leveraged to generate evidence related to nursing practice. Several widely-reported nursing specific terminologies and classifications systems currently exist including the Clinical Care Classification System, International Classification for Nursing Practice(®), Nursing Intervention Classification, Nursing Outcome Classification, Omaha System, Perioperative Nursing Data Set and NANDA International. However, the influence of these systems on demonstrating the value of nursing and the professions' impact on quality, safety and patient outcomes in published research is relatively unknown. This paper seeks to understand the use of standardized nursing terminology and classification systems in published research, using the International Classification for Nursing Practice(®) as a case study. A systematic review of international published empirical studies on, or using, the International Classification for Nursing Practice(®) were completed using Medline and the Cumulative Index for Nursing and Allied Health Literature. Since 2006, 38 studies have been published on the International Classification for Nursing Practice(®). The main objectives of the published studies have been to validate the appropriateness of the classification system for particular care areas or populations, further develop the classification system, or utilize it to support the generation of new nursing knowledge. To date, most studies have focused on the classification system itself, and a lesser number of studies have used the system to generate information about the outcomes of nursing practice. Based on the published literature that features the International Classification for Nursing Practice, standardized nursing terminology and classification systems appear to be well developed for various populations, settings and to harmonize with other health-related terminology systems. However, the use of the systems to generate new nursing knowledge, and to validate nursing practice is still in its infancy. There is an opportunity now to utilize the well-developed systems in their current state to further what is know about nursing practice, and how best to demonstrate improvements in patient outcomes through nursing care. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

A Novel UAV Electric Propulsion Testbed for Diagnostics and Prognostics

NASA Technical Reports Server (NTRS)

Gorospe, George E., Jr.; Kulkarni, Chetan S.

2017-01-01

This paper presents a novel hardware-in-the-loop (HIL) testbed for systems level diagnostics and prognostics of an electric propulsion system used in UAVs (unmanned aerial vehicle). Referencing the all electric, Edge 540T aircraft used in science and research by NASA Langley Flight Research Center, the HIL testbed includes an identical propulsion system, consisting of motors, speed controllers and batteries. Isolated under a controlled laboratory environment, the propulsion system has been instrumented for advanced diagnostics and prognostics. To produce flight like loading on the system a slave motor is coupled to the motor under test (MUT) and provides variable mechanical resistance, and the capability of introducing nondestructive mechanical wear-like frictional loads on the system. This testbed enables the verification of mathematical models of each component of the propulsion system, the repeatable generation of flight-like loads on the system for fault analysis, test-to-failure scenarios, and the development of advanced system level diagnostics and prognostics methods. The capabilities of the testbed are extended through the integration of a LabVIEW-based client for the Live Virtual Constructive Distributed Environment (LVCDC) Gateway which enables both the publishing of generated data for remotely located observers and prognosers and the synchronization the testbed propulsion system with vehicles in the air. The developed HIL testbed gives researchers easy access to a scientifically relevant portion of the aircraft without the overhead and dangers encountered during actual flight.

Implementation of Particle Swarm Optimization Method for Voltage Stability Analysis in 150 kV Sub System Grati – Paiton East Java

NASA Astrophysics Data System (ADS)

Kusumaningtyas, A. B.; Hidayat, M. N.; Ronilaya, F.

2018-04-01

Based on the data from State Electric Company on 15 January 2013, the undistributed power in the 150 kV sub system Grati-Paiton Region IV, that consist of 26 bus 150 kV and 2 bus generation 500 kV system, was recorded 3.286,00 MW. At the same time, the frequency of the system was down to 49 Hz. This lead to a deficit generation and unstable voltage condition in the system. Fast Voltage Stability Index (FVSI) method is used in this research to analyze the voltage stability of the buses. For buses with unstable voltage condition, reactive power will be injected through capacitor installation. The site where the capacitor will be installed is determined using the Fast Voltage Stability Index (FVSI) method while the size of the capacitor is determined using the Particle Swarm Optimization (PSO) method. The PSO method has been applied in some researches, such as to determine optimal placement and sizing in radial distribution network as well as in transmission network.. In this research, the PSO method is used to find the Qloss of an interconnection transmission system, which in turn, the value of the Qloss is used to determine the capacitance of the capacitor needed by the system.

Next Steps: Water Technology Advances (Research)

EPA Science Inventory

This project will focus on contaminants and their impact on health, adequate removal of contaminants from various water systems, and water and resource recovery within treatment systems. It will develop the next generation of technological advances to provide guidance in support ...

High Reynolds Number Micro-Bubble and Polymer Drag Reduction Experiments

DTIC Science & Technology

2008-01-01

systems . Researchers have known for more than fifty years that the presence of high molecular weight polymers in the near-wall region of a turbulent...drag reduction (ALDR) (see Winkel, 2006). We present here a brief review of BDR and ALDR research . A seminal study of BDR was conducted 35 years ago when...SR830 DSP LIA, Stanford Research Systems ) and a signal generator. (8904A multifunction synthesizer, HP) were used to excite and balance the bridge as

Nextgen Technologies for Mid-Term and Far-Term Air Traffic Control Operations

NASA Technical Reports Server (NTRS)

Prevot, Thomas

2009-01-01

This paper describes technologies for mid-term and far-term air traffic control operations in the Next Generation Air Transportation System (NextGen). The technologies were developed and evaluated with human-in-the-loop simulations in the Airspace Operations Laboratory (AOL) at the NASA Ames Research Center. The simulations were funded by several research focus areas within NASA's Airspace Systems program and some were co-funded by the FAA's Air Traffic Organization for Planning, Research and Technology.

Toolsets Maintain Health of Complex Systems

NASA Technical Reports Server (NTRS)

2010-01-01

First featured in Spinoff 2001, Qualtech Systems Inc. (QSI), of Wethersfield, Connecticut, adapted its Testability, Engineering, and Maintenance System (TEAMS) toolset under Small Business Innovation Research (SBIR) contracts from Ames Research Center to strengthen NASA's systems health management approach for its large, complex, and interconnected systems. Today, six NASA field centers utilize the TEAMS toolset, including TEAMS-Designer, TEAMS-RT, TEAMATE, and TEAMS-RDS. TEAMS is also being used on industrial systems that generate power, carry data, refine chemicals, perform medical functions, and produce semiconductor wafers. QSI finds TEAMS can lower costs by decreasing problems requiring service by 30 to 50 percent.

Design of a Mission Data Storage and Retrieval System for NASA Dryden Flight Research Center

NASA Technical Reports Server (NTRS)

Lux, Jessica; Downing, Bob; Sheldon, Jack

2007-01-01

The Western Aeronautical Test Range (WATR) at the NASA Dryden Flight Research Center (DFRC) employs the WATR Integrated Next Generation System (WINGS) for the processing and display of aeronautical flight data. This report discusses the post-mission segment of the WINGS architecture. A team designed and implemented a system for the near- and long-term storage and distribution of mission data for flight projects at DFRC, providing the user with intelligent access to data. Discussed are the legacy system, an industry survey, system operational concept, high-level system features, and initial design efforts.

Spacecraft software training needs assessment research, appendices

NASA Technical Reports Server (NTRS)

Ratcliff, Shirley; Golas, Katharine

1990-01-01

The appendices to the previously reported study are presented: statistical data from task rating worksheets; SSD references; survey forms; fourth generation language, a powerful, long-term solution to maintenance cost; task list; methodology; SwRI's instructional systems development model; relevant research; and references.

National Centers for Environmental Prediction

Science.gov Websites

Statistics Observational Data Processing Data Assimilation Monsoon Desk Model Transition Seminars Seminar Observing system Research and Predictability EXperiment (THORPEX) Targeted Obs Targeted Observations Cyclone University Research Court College Park, MD 20740 Page Author: EMC Webmaster Page generated:Sunday, 27-May

Interactive web-based mapping: bridging technology and data for health.

PubMed

Highfield, Linda; Arthasarnprasit, Jutas; Ottenweller, Cecelia A; Dasprez, Arnaud

2011-12-23

The Community Health Information System (CHIS) online mapping system was first launched in 1998. Its overarching goal was to provide researchers, residents and organizations access to health related data reflecting the overall health and well-being of their communities within the Greater Houston area. In September 2009, initial planning and development began for the next generation of CHIS. The overarching goal for the new version remained to make health data easily accessible for a wide variety of research audiences. However, in the new version we specifically sought to make the CHIS truly interactive and give the user more control over data selection and reporting. In July 2011, a beta version of the next-generation of the application was launched. This next-generation is also a web based interactive mapping tool comprised of two distinct portals: the Breast Health Portal and Project Safety Net. Both are accessed via a Google mapping interface. Geographic coverage for the portals is currently an 8 county region centered on Harris County, Texas. Data accessed by the application include Census 2000, Census 2010 (underway), cancer incidence from the Texas Cancer Registry (TX Dept. of State Health Services), death data from Texas Vital Statistics, clinic locations for free and low-cost health services, along with service lists, hours of operation, payment options and languages spoken, uninsured and poverty data. The system features query on the fly technology, which means the data is not generated until the query is provided to the system. This allows users to interact in real-time with the databases and generate customized reports and maps. To the author's knowledge, the Breast Health Portal and Project Safety Net are the first local-scale interactive online mapping interfaces for public health data which allow users to control the data generated. For example, users may generate breast cancer incidence rates by Census tract, in real time, for women aged 40-64. Conversely, they could then generate the same rates for women aged 35-55. The queries are user controlled.

Energy research information system projects report, volume 5, number 1

NASA Astrophysics Data System (ADS)

Johnson, J.; Schillinger, L.

1980-07-01

The system (ERIS) provides an inventory of the energy related programs and research activities from 1974 to the present in the states of Montana, Nebraska, North Dakota, South Dakota and Wyoming. Areas of research covered include coal, reclamation, water resources, environmental impacts, socioeconomic impacts, energy conversion, mining methodology, petroleum, natural gas, oilshale, renewable energy resources, nuclear energy, energy conservation and land use. Each project description lists title, investigator(s), research institution, sponsor, funding, time frame, location, a descriptive abstract of the research and title reports and/or publications generated by the research. All projects are indexed by location, personal names, organizations and subject keywords.

SCALS: a fourth-generation study of assisted living technologies in their organisational, social, political and policy context

PubMed Central

Greenhalgh, Trisha; Shaw, Sara; Wherton, Joe; Hughes, Gemma; Lynch, Jenni; A'Court, Christine; Hinder, Sue; Fahy, Nick; Byrne, Emma; Finlayson, Alexander; Sorell, Tom; Procter, Rob; Stones, Rob

2016-01-01

Introduction Research to date into assisted living technologies broadly consists of 3 generations: technical design, experimental trials and qualitative studies of the patient experience. We describe a fourth-generation paradigm: studies of assisted living technologies in their organisational, social, political and policy context. Fourth-generation studies are necessarily organic and emergent; they view technology as part of a dynamic, networked and potentially unstable system. They use co-design methods to generate and stabilise local solutions, taking account of context. Methods and analysis SCALS (Studies in Co-creating Assisted Living Solutions) consists (currently) of 5 organisational case studies, each an English health or social care organisation striving to introduce technology-supported services to support independent living in people with health and/or social care needs. Treating these cases as complex systems, we seek to explore interdependencies, emergence and conflict. We employ a co-design approach informed by the principles of action research to help participating organisations establish, refine and evaluate their service. To that end, we are conducting in-depth ethnographic studies of people's experience of assisted living technologies (micro level), embedded in evolving organisational case studies that use interviews, ethnography and document analysis (meso level), and exploring the wider national and international context for assisted living technologies and policy (macro level). Data will be analysed using a sociotechnical framework developed from structuration theory. Ethics and dissemination Research ethics approval for the first 4 case studies has been granted. An important outcome will be lessons learned from individual co-design case studies. We will document the studies’ credibility and rigour, and assess the transferability of findings to other settings while also recognising unique aspects of the contexts in which they were generated. Academic outputs will include a cross-case analysis and progress in theory and method of fourth-generation assisted living technology research. We will produce practical guidance for organisations, policymakers, designers and service users. PMID:26880671

Application of Earth Sciences Products for use in Next Generation Numerical Aerosol Prediction Models

DTIC Science & Technology

2008-09-30

retrievals, Geophysical Research Abstracts, Vol. 10, EGU2008-A-11193, 2008, SRef-ID: 1607-7962/gra/EGU2008-A­ 11193, EGU General Assembly 2008. Liu, M...Application of Earth Sciences Products for use in Next Generation Numerical Aerosol...can be generated and predicted. Through this system, we will be able to advance a number of US Navy Applied Science needs in the areas of improved

Electricity Market Games: How Agent-Based Modeling Can Help under High Penetrations of Variable Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gallo, Giulia

Integrating increasingly high levels of variable generation in U.S. electricity markets requires addressing not only power system and grid modeling challenges but also an understanding of how market participants react and adapt to them. Key elements of current and future wholesale power markets can be modeled using an agent-based approach, which may prove to be a useful paradigm for researchers studying and planning for power systems of the future.

Modeling complex dispersed energy and clean water systems for the United States/Mexico border

NASA Astrophysics Data System (ADS)

Herrera, Hugo Francisco Lopez

As world population grows, and its technology evolves, the demand for electricity inexorably increases. Until now most of this electricity has been produced via fossil fuels, non-renewable energy resources that are irreversibly deteriorating our environment. On the economical aspect it does not get any better. Let's not forget market rules, the higher the demand and lower the offer, the higher the price we will have to pay. Oil is an excellent example. Some countries try to solve this situation with Pharaohnic projects, i.e. investing absurd amounts of money in 'green electricity' building monstrous dams to power equally monstrous hydroelectric power plants. The only problem with this is that it is not green at all---it does have an enormous environmental impact---it is extremely complicated and expensive to implement. It is important to point out, that this research project does not try to solve world's thirst for electricity. It is rather aimed to help solve this problematic at a much lower scale---it should be considered as an extremely small step in the right direction. It focuses on satisfying the local electricity needs with renewable, non-contaminating and locally available resources. More concisely, this project focuses on the attainment and use of hydrogen as an alternate energy source in El Paso/Juarez region. Clean technology is nowadays available to produce hydrogen and oxygen, i.e. the photoelectrolysis process. Photovoltaic cells coupled with electrolytic devices can be used to produce hydrogen and oxygen in a sustainable manner. In this research, simulation models of hybrid systems were designed and developed. They were capable to compare, predict and evaluate different options for hydrogen generation. On the other hand, with the produced hydrogen from the electrolysis process it was possible to generate electricity through fuel cells. The main objectives of the proposed research were to define how to use the resources for the attainment of hydrogen and distribution of it in El Paso/Juarez region. More precisely, the goals were the conversion of brines and waste-waters to hydrogen via electrolysis, and the generation of electricity through fuel cells. Thereafter, the specific objectives were to (1) design a simulation model for hydrogen generation, (2) design and simulate a model of photovoltaic (PV) array capable to generate the required energy for the process, (3) simulate fuel cells in order to be used as electricity power supply in remote houses, and (4) simulate a complete remote house hybrid system. The results of this research gave us information about the feasibility of high-volume hydrogen generation with the diverse resources of the region. On the other hand, this research has shown the alternatives of local energy generation, and efficiency of a remote house hybrid system located in El Paso/Juarez area. Experiences obtained from this research will also provide information for future investigations in the field of alternate energy sources, in order to get a clean environment through sustainable development.

Case Report Form Reporter: A Key Component for the Integration of Electronic Medical Records and the Electronic Data Capture System.

PubMed

Matsumura, Yasushi; Hattori, Atsushi; Manabe, Shiro; Takahashi, Daiyo; Yamamoto, Yuichiro; Murata, Taizo; Nakagawa, Akito; Mihara, Naoki; Takeda, Toshihiro

2017-01-01

To improve the efficiency of clinical research, we developed a system to integrate electronic medical records (EMRs) and the electronic data capture system (EDC). EDC is divided into case report form (CRF) reporter and CDMS with CRF receiver with data communication using the operational data model (ODM). The CRF reporter is incorporated into the EMR to share data witth the EMR. In the data transcription type, doctors enter data using a progress note template, which are transmitted to the reporter template. It then generates the ODM. In the direct record type, reporter templates open from the progress note and generate narrative text to make record in the progress note. The configuration files for a study are delivered from the contents server to minimize the setup. This system has been used for 15 clinical studies including 3 clinical trials. This system can save labor and financial costs in clinical research.

Not as Easy as It Sounds: Designing a Balanced Assessment System

ERIC Educational Resources Information Center

Chattergoon, Rajendra; Marion, Scott

2016-01-01

Many states and school districts are rethinking how they do educational assessment. A few are going further: attempting to build "balanced," "comprehensive," or "next-generation" assessment systems. At the same time, practitioners and researchers have long mulled the purposes and parts such systems should have. But…

Architectures Toward Reusable Science Data Systems

NASA Astrophysics Data System (ADS)

Moses, J. F.

2014-12-01

Science Data Systems (SDS) comprise an important class of data processing systems that support product generation from remote sensors and in-situ observations. These systems enable research into new science data products, replication of experiments and verification of results. NASA has been building ground systems for satellite data processing since the first Earth observing satellites launched and is continuing development of systems to support NASA science research, NOAA's weather satellites and USGS's Earth observing satellite operations. The basic data processing workflows and scenarios continue to be valid for remote sensor observations research as well as for the complex multi-instrument operational satellite data systems being built today. System functions such as ingest, product generation and distribution need to be configured and performed in a consistent and repeatable way with an emphasis on scalability. This paper will examine the key architectural elements of several NASA satellite data processing systems currently in operation and under development that make them suitable for scaling and reuse. Examples of architectural elements that have become attractive include virtual machine environments, standard data product formats, metadata content and file naming, workflow and job management frameworks, data acquisition, search, and distribution protocols. By highlighting key elements and implementation experience the goal is to recognize architectures that will outlast their original application and be readily adaptable for new applications. Concepts and principles are explored that lead to sound guidance for SDS developers and strategists.

The emerging genomics and systems biology research lead to systems genomics studies.

PubMed

Yang, Mary Qu; Yoshigoe, Kenji; Yang, William; Tong, Weida; Qin, Xiang; Dunker, A; Chen, Zhongxue; Arbania, Hamid R; Liu, Jun S; Niemierko, Andrzej; Yang, Jack Y

2014-01-01

Synergistically integrating multi-layer genomic data at systems level not only can lead to deeper insights into the molecular mechanisms related to disease initiation and progression, but also can guide pathway-based biomarker and drug target identification. With the advent of high-throughput next-generation sequencing technologies, sequencing both DNA and RNA has generated multi-layer genomic data that can provide DNA polymorphism, non-coding RNA, messenger RNA, gene expression, isoform and alternative splicing information. Systems biology on the other hand studies complex biological systems, particularly systematic study of complex molecular interactions within specific cells or organisms. Genomics and molecular systems biology can be merged into the study of genomic profiles and implicated biological functions at cellular or organism level. The prospectively emerging field can be referred to as systems genomics or genomic systems biology. The Mid-South Bioinformatics Centre (MBC) and Joint Bioinformatics Ph.D. Program of University of Arkansas at Little Rock and University of Arkansas for Medical Sciences are particularly interested in promoting education and research advancement in this prospectively emerging field. Based on past investigations and research outcomes, MBC is further utilizing differential gene and isoform/exon expression from RNA-seq and co-regulation from the ChiP-seq specific for different phenotypes in combination with protein-protein interactions, and protein-DNA interactions to construct high-level gene networks for an integrative genome-phoneme investigation at systems biology level.

Architectures Toward Reusable Science Data Systems

NASA Technical Reports Server (NTRS)

Moses, John

2015-01-01

Science Data Systems (SDS) comprise an important class of data processing systems that support product generation from remote sensors and in-situ observations. These systems enable research into new science data products, replication of experiments and verification of results. NASA has been building systems for satellite data processing since the first Earth observing satellites launched and is continuing development of systems to support NASA science research and NOAAs Earth observing satellite operations. The basic data processing workflows and scenarios continue to be valid for remote sensor observations research as well as for the complex multi-instrument operational satellite data systems being built today. System functions such as ingest, product generation and distribution need to be configured and performed in a consistent and repeatable way with an emphasis on scalability. This paper will examine the key architectural elements of several NASA satellite data processing systems currently in operation and under development that make them suitable for scaling and reuse. Examples of architectural elements that have become attractive include virtual machine environments, standard data product formats, metadata content and file naming, workflow and job management frameworks, data acquisition, search, and distribution protocols. By highlighting key elements and implementation experience we expect to find architectures that will outlast their original application and be readily adaptable for new applications. Concepts and principles are explored that lead to sound guidance for SDS developers and strategists.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myronakis, M; Cai, W; Dhou, S

Purpose: To design a comprehensive open-source, publicly available, graphical user interface (GUI) to facilitate the configuration, generation, processing and use of the 4D Extended Cardiac-Torso (XCAT) phantom. Methods: The XCAT phantom includes over 9000 anatomical objects as well as respiratory, cardiac and tumor motion. It is widely used for research studies in medical imaging and radiotherapy. The phantom generation process involves the configuration of a text script to parameterize the geometry, motion, and composition of the whole body and objects within it, and to generate simulated PET or CT images. To avoid the need for manual editing or script writing,more » our MATLAB-based GUI uses slider controls, drop-down lists, buttons and graphical text input to parameterize and process the phantom. Results: Our GUI can be used to: a) generate parameter files; b) generate the voxelized phantom; c) combine the phantom with a lesion; d) display the phantom; e) produce average and maximum intensity images from the phantom output files; f) incorporate irregular patient breathing patterns; and f) generate DICOM files containing phantom images. The GUI provides local help information using tool-tip strings on the currently selected phantom, minimizing the need for external documentation. The DICOM generation feature is intended to simplify the process of importing the phantom images into radiotherapy treatment planning systems or other clinical software. Conclusion: The GUI simplifies and automates the use of the XCAT phantom for imaging-based research projects in medical imaging or radiotherapy. This has the potential to accelerate research conducted with the XCAT phantom, or to ease the learning curve for new users. This tool does not include the XCAT phantom software itself. We would like to acknowledge funding from MRA, Varian Medical Systems Inc.« less

ARO-URI Center for Opto-Electronic Systems Research. Addendum

DTIC Science & Technology

1992-12-01

5, 2015-2020 (1988). 36. "Cancellation of laser phase fluctuations in Stokes and anti-Stokes generation ," Z . W. Li, C. Radzewicz, and M. G. Raymer, J...G. Raymer, Opt. Lett. 13, 491-493 (1988). (34) "Cancellation of laser phase fluctuations in Stokes and anti-Stokes generation ," Z . W. Li, C

Summary of atmospheric wind design criteria for wind energy conversion system development

NASA Technical Reports Server (NTRS)

Frost, W.; Turner, R. E.

1979-01-01

Basic design values are presented of significant wind criteria, in graphical format, for use in the design and development of wind turbine generators for energy research. It is a condensed version of portions of the Engineering Handbook on the Atmospheric Environmental Guidelines for Use in Wind Turbine Generator Development.

Do Community Colleges Promote Postsecondary and Labor Market Success for First-Generation Students

ERIC Educational Resources Information Center

Ampaw, Frimpomaa; Partlo, Margaret; Hullender, Tammy; Wagner, Nick

2015-01-01

Community colleges are becoming the primary access point for a growing number of underrepresented and underserved students in the higher education system. First-generation college students make up a large proportion of this population, comprising about 45% of community college attendees (Nomi, 2005). Research has explored the transfer success of…

Examinations Wash Back Effects: Challenges to the Criterion Referenced Assessment Model

ERIC Educational Resources Information Center

Mogapi, M.

2016-01-01

Examinations play a central role in the educational system due to the fact that information generated from examinations is used for a variety of purposes. Critical decisions such as selection, placement and determining the instructional effectives of a programme of study all depend on data generated from examinations. Numerous research studies…

High temperature, harsh environment sensors for advanced power generation systems

NASA Astrophysics Data System (ADS)

Ohodnicki, P. R.; Credle, S.; Buric, M.; Lewis, R.; Seachman, S.

2015-05-01

One mission of the Crosscutting Technology Research program at the National Energy Technology Laboratory is to develop a suite of sensors and controls technologies that will ultimately increase efficiencies of existing fossil-fuel fired power plants and enable a new generation of more efficient and lower emission power generation technologies. The program seeks to accomplish this mission through soliciting, managing, and monitoring a broad range of projects both internal and external to the laboratory which span sensor material and device development, energy harvesting and wireless telemetry methodologies, and advanced controls algorithms and approaches. A particular emphasis is placed upon harsh environment sensing for compatibility with high temperature, erosive, corrosive, and highly reducing or oxidizing environments associated with large-scale centralized power generation. An overview of the full sensors and controls portfolio is presented and a selected set of current and recent research successes and on-going projects are highlighted. A more detailed emphasis will be placed on an overview of the current research thrusts and successes of the in-house sensor material and device research efforts that have been established to support the program.

Security Frameworks for Machine-to-Machine Devices and Networks

NASA Astrophysics Data System (ADS)

Demblewski, Michael

Attacks against mobile systems have escalated over the past decade. There have been increases of fraud, platform attacks, and malware. The Internet of Things (IoT) offers a new attack vector for Cybercriminals. M2M contributes to the growing number of devices that use wireless systems for Internet connection. As new applications and platforms are created, old vulnerabilities are transferred to next-generation systems. There is a research gap that exists between the current approaches for security framework development and the understanding of how these new technologies are different and how they are similar. This gap exists because system designers, security architects, and users are not fully aware of security risks and how next-generation devices can jeopardize safety and personal privacy. Current techniques, for developing security requirements, do not adequately consider the use of new technologies, and this weakens countermeasure implementations. These techniques rely on security frameworks for requirements development. These frameworks lack a method for identifying next generation security concerns and processes for comparing, contrasting and evaluating non-human device security protections. This research presents a solution for this problem by offering a novel security framework that is focused on the study of the "functions and capabilities" of M2M devices and improves the systems development life cycle for the overall IoT ecosystem.

MEMS Rotary Engine Power System

NASA Astrophysics Data System (ADS)

Fernandez-Pello, A. Carlos; Pisano, Albert P.; Fu, Kelvin; Walther, David C.; Knobloch, Aaron; Martinez, Fabian; Senesky, Matt; Stoldt, Conrad; Maboudian, Roya; Sanders, Seth; Liepmann, Dorian

This work presents a project overview and recent research results for the MEMS Rotary Engine Power System project at the Berkeley Sensor & Actuator Center of the University of California at Berkeley. The research motivation for the project is the high specific energy density of hydrocarbon fuels. When compared with the energy density of batteries, hydrocarbon fuels may have as much as 20x more energy. However, the technical challenge is the conversion of hydrocarbon fuel to electricity in an efficient and clean micro engine. A 12.9 mm diameter Wankel engine will be shown that has already generated 4 Watts of power at 9300rpm. In addition, the 1mm and 2.4 mm Wankel engines that BSAC is developing for power generation at the microscale will be discussed. The project goal is to develop electrical power output of 90milliwatts from the 2.4 mm engine. Prototype engine components have already been fabricated and these will be described. The integrated generator design concept utilizes a nickel-iron alloy electroplated in the engine rotor poles, so that the engine rotor also serves as the generator rotor.

Operational algorithm development and refinement approaches

NASA Astrophysics Data System (ADS)

Ardanuy, Philip E.

2003-11-01

Next-generation polar and geostationary systems, such as the National Polar-orbiting Operational Environmental Satellite System (NPOESS) and the Geostationary Operational Environmental Satellite (GOES)-R, will deploy new generations of electro-optical reflective and emissive capabilities. These will include low-radiometric-noise, improved spatial resolution multi-spectral and hyperspectral imagers and sounders. To achieve specified performances (e.g., measurement accuracy, precision, uncertainty, and stability), and best utilize the advanced space-borne sensing capabilities, a new generation of retrieval algorithms will be implemented. In most cases, these advanced algorithms benefit from ongoing testing and validation using heritage research mission algorithms and data [e.g., the Earth Observing System (EOS)] Moderate-resolution Imaging Spectroradiometer (MODIS) and Shuttle Ozone Limb Scattering Experiment (SOLSE)/Limb Ozone Retreival Experiment (LORE). In these instances, an algorithm's theoretical basis is not static, but rather improves with time. Once frozen, an operational algorithm can "lose ground" relative to research analogs. Cost/benefit analyses provide a basis for change management. The challenge is in reconciling and balancing the stability, and "comfort," that today"s generation of operational platforms provide (well-characterized, known, sensors and algorithms) with the greatly improved quality, opportunities, and risks, that the next generation of operational sensors and algorithms offer. By using the best practices and lessons learned from heritage/groundbreaking activities, it is possible to implement an agile process that enables change, while managing change. This approach combines a "known-risk" frozen baseline with preset completion schedules with insertion opportunities for algorithm advances as ongoing validation activities identify and repair areas of weak performance. This paper describes an objective, adaptive implementation roadmap that takes into account the specific maturities of each system"s (sensor and algorithm) technology to provide for a program that contains continuous improvement while retaining its manageability.

Mitigating Short-Term Variations of Photovoltaic Generation Using Energy Storage with VOLTTRON

NASA Astrophysics Data System (ADS)

Morrissey, Kevin

A smart-building communications system performs smoothing on photovoltaic (PV) power generation using a battery energy storage system (BESS). The system runs using VOLTTRON(TM), a multi-agent python-based software platform dedicated to power systems. The VOLTTRON(TM) system designed for this project runs synergistically with the larger University of Washington VOLTTRON(TM) environment, which is designed to operate UW device communications and databases as well as to perform real-time operations for research. One such research algorithm that operates simultaneously with this PV Smoothing System is an energy cost optimization system which optimizes net demand and associated cost throughout a day using the BESS. The PV Smoothing System features an active low-pass filter with an adaptable time constant, as well as adjustable limitations on the output power and accumulated battery energy of the BESS contribution. The system was analyzed using 26 days of PV generation at 1-second resolution. PV smoothing was studied with unconstrained BESS contribution as well as under a broad range of BESS constraints analogous to variable-sized storage. It was determined that a large inverter output power was more important for PV smoothing than a large battery energy capacity. Two methods of selecting the time constant in real time, static and adaptive, are studied for their impact on system performance. It was found that both systems provide a high level of PV smoothing performance, within 8% of the ideal case where the best time constant is known ahead of time. The system was run in real time using VOLTTRON(TM) with BESS limitations of 5 kW/6.5 kWh and an adaptive update period of 7 days. The system behaved as expected given the BESS parameters and time constant selection methods, providing smoothing on the PV generation and updating the time constant periodically using the adaptive time constant selection method.

Encapsulated Optically Responsive Cell Systems: Toward Smart Implants in Biomedicine.

PubMed

Boss, Christophe; Bouche, Nicolas; De Marchi, Umberto

2018-04-01

Managing increasingly prevalent chronic diseases will require close continuous monitoring of patients. Cell-based biosensors may be used for implantable diagnostic systems to monitor health status. Cells are indeed natural sensors in the body. Functional cellular systems can be maintained in the body for long-term implantation using cell encapsulation technology. By taking advantage of recent progress in miniaturized optoelectronic systems, the genetic engineering of optically responsive cells may be combined with cell encapsulation to generate smart implantable cell-based sensing systems. In biomedical research, cell-based biosensors may be used to study cell signaling, therapeutic effects, and dosing of bioactive molecules in preclinical models. Today, a wide variety of genetically encoded fluorescent sensors have been developed for real-time imaging of living cells. Here, recent developments in genetically encoded sensors, cell encapsulation, and ultrasmall optical systems are highlighted. The integration of these components in a new generation of biosensors is creating innovative smart in vivo cell-based systems, bringing novel perspectives for biomedical research and ultimately allowing unique health monitoring applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Rocket engine diagnostics using qualitative modeling techniques

NASA Technical Reports Server (NTRS)

Binder, Michael; Maul, William; Meyer, Claudia; Sovie, Amy

1992-01-01

Researchers at NASA Lewis Research Center are presently developing qualitative modeling techniques for automated rocket engine diagnostics. A qualitative model of a turbopump interpropellant seal system has been created. The qualitative model describes the effects of seal failures on the system steady-state behavior. This model is able to diagnose the failure of particular seals in the system based on anomalous temperature and pressure values. The anomalous values input to the qualitative model are generated using numerical simulations. Diagnostic test cases include both single and multiple seal failures.

Rocket engine diagnostics using qualitative modeling techniques

NASA Technical Reports Server (NTRS)

Binder, Michael; Maul, William; Meyer, Claudia; Sovie, Amy

1992-01-01

Researchers at NASA Lewis Research Center are presently developing qualitative modeling techniques for automated rocket engine diagnostics. A qualitative model of a turbopump interpropellant seal system was created. The qualitative model describes the effects of seal failures on the system steady state behavior. This model is able to diagnose the failure of particular seals in the system based on anomalous temperature and pressure values. The anomalous values input to the qualitative model are generated using numerical simulations. Diagnostic test cases include both single and multiple seal failures.

Conceptual Systems Model as a Tool for Hypothesis Generation and Testing in Ecotoxicological Research

EPA Science Inventory

Microarray, proteomic, and metabonomic technologies are becoming increasingly accessible as tools for ecotoxicology research. Effective use of these technologies will depend, at least in part, on the ability to apply these techniques within a paradigm of hypothesis driven researc...

10 CFR 35.290 - Training for imaging and localization studies.

Code of Federal Regulations, 2013 CFR

2013-01-01

...; (D) Chemistry of byproduct material for medical use; (E) Radiation biology; and (ii) Work experience... human research subject dosages; (D) Using administrative controls to prevent a medical event involving... patients or human research subjects; and (G) Eluting generator systems appropriate for preparation of...

10 CFR 35.290 - Training for imaging and localization studies.

Code of Federal Regulations, 2012 CFR

2012-01-01

...; (D) Chemistry of byproduct material for medical use; (E) Radiation biology; and (ii) Work experience... human research subject dosages; (D) Using administrative controls to prevent a medical event involving... patients or human research subjects; and (G) Eluting generator systems appropriate for preparation of...

10 CFR 35.290 - Training for imaging and localization studies.

Code of Federal Regulations, 2011 CFR

2011-01-01

...; (D) Chemistry of byproduct material for medical use; (E) Radiation biology; and (ii) Work experience... human research subject dosages; (D) Using administrative controls to prevent a medical event involving... patients or human research subjects; and (G) Eluting generator systems appropriate for preparation of...

10 CFR 35.290 - Training for imaging and localization studies.

Code of Federal Regulations, 2014 CFR

2014-01-01

...; (D) Chemistry of byproduct material for medical use; (E) Radiation biology; and (ii) Work experience... human research subject dosages; (D) Using administrative controls to prevent a medical event involving... patients or human research subjects; and (G) Eluting generator systems appropriate for preparation of...

Load Frequency Control by use of a Number of Both Heat Pump Water Heaters and Electric Vehicles in Power System with a Large Integration of Renewable Energy Sources

NASA Astrophysics Data System (ADS)

Masuta, Taisuke; Shimizu, Koichiro; Yokoyama, Akihiko

In Japan, from the viewpoints of global warming countermeasures and energy security, it is expected to establish a smart grid as a power system into which a large amount of generation from renewable energy sources such as wind power generation and photovoltaic generation can be installed. Measures for the power system stability and reliability are necessary because a large integration of these renewable energy sources causes some problems in power systems, e.g. frequency fluctuation and distribution voltage rise, and Battery Energy Storage System (BESS) is one of effective solutions to these problems. Due to a high cost of the BESS, our research group has studied an application of controllable loads such as Heat Pump Water Heater (HPWH) and Electric Vehicle (EV) to the power system control for reduction of the required capacity of BESS. This paper proposes a new coordinated Load Frequency Control (LFC) method for the conventional power plants, the BESS, the HPWHs, and the EVs. The performance of the proposed LFC method is evaluated by the numerical simulations conducted on a power system model with a large integration of wind power generation and photovoltaic generation.

Doubly fed induction generator wind turbines with fuzzy controller: a survey.

PubMed

Sathiyanarayanan, J S; Kumar, A Senthil

2014-01-01

Wind energy is one of the extraordinary sources of renewable energy due to its clean character and free availability. With the increasing wind power penetration, the wind farms are directly influencing the power systems. The majority of wind farms are using variable speed wind turbines equipped with doubly fed induction generators (DFIG) due to their advantages over other wind turbine generators (WTGs). Therefore, the analysis of wind power dynamics with the DFIG wind turbines has become a very important research issue, especially during transient faults. This paper presents fuzzy logic control of doubly fed induction generator (DFIG) wind turbine in a sample power system. Fuzzy logic controller is applied to rotor side converter for active power control and voltage regulation of wind turbine.

Futurescapes: evidence expectations in the USA for comparative effectiveness research for drugs in 2020.

PubMed

Messner, Donna A; Mohr, Penny; Towse, Adrian

2015-08-01

Explore key factors influencing future expectations for the production of evidence from comparative effectiveness research for drugs in the USA in 2020 and construct three plausible future scenarios. Semistructured key informant interviews and three rounds of modified Delphi with systematic scenario-building methods. Most influential key factors were: health delivery system integration; electronic health record development; exploitation of very large databases and mixed data sources; and proactive patient engagement in research. The scenario deemed most likely entailed uneven development of large integrated health systems with pockets of increased provider risk for patient care, enhanced data collection systems, changing incentives to do comparative effectiveness research and new opportunities for evidence generation partnerships.

Truck Thermoacoustic Generator and Chiller

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keolian, Robert

2011-03-31

This Final Report describes the accomplishments of the US Department of Energy (DOE) cooperative agreement project DE-FC26-04NT42113 - Truck Thermoacoustic Generator and Chiller - whose goal is to design, fabricate and test a thermoacoustic piezoelectric generator and chiller system for use on over-the-road heavy-duty-diesel trucks, driven alternatively by the waste heat of the main diesel engine exhaust or by a burner integrated into the thermoacoustic system. The thermoacoustic system would utilize engine exhaust waste heat to generate electricity and cab air conditioning, and would also function as an auxiliary power unit (APU) for idle reduction. The unit was to bemore » tested in Volvo engine performance and endurance test cells and then integrated onto a Class 8 over-the-road heavy-duty-diesel truck for further testing on the road. The project has been a collaboration of The Pennsylvania State University Applied Research Laboratory, Los Alamos National Laboratory, Clean Power Resources Inc., and Volvo Powertrain (Mack Trucks Inc.). Cost share funding was provided by Applied Research Laboratory, and by Clean Power Resources Inc via its grant from Innovation Works - funding that was derived from the Commonwealth of Pennsylvania. Los Alamos received its funding separately through DOE Field Work Proposal 04EE09.« less

Big data and new knowledge in medicine: the thinking, training, and tools needed for a learning health system.

PubMed

Krumholz, Harlan M

2014-07-01

Big data in medicine--massive quantities of health care data accumulating from patients and populations and the advanced analytics that can give those data meaning--hold the prospect of becoming an engine for the knowledge generation that is necessary to address the extensive unmet information needs of patients, clinicians, administrators, researchers, and health policy makers. This article explores the ways in which big data can be harnessed to advance prediction, performance, discovery, and comparative effectiveness research to address the complexity of patients, populations, and organizations. Incorporating big data and next-generation analytics into clinical and population health research and practice will require not only new data sources but also new thinking, training, and tools. Adequately utilized, these reservoirs of data can be a practically inexhaustible source of knowledge to fuel a learning health care system. Project HOPE—The People-to-People Health Foundation, Inc.

Big Data And New Knowledge In Medicine: The Thinking, Training, And Tools Needed For A Learning Health System

PubMed Central

Krumholz, Harlan M.

2017-01-01

Big data in medicine--massive quantities of health care data accumulating from patients and populations and the advanced analytics that can give it meaning--hold the prospect of becoming an engine for the knowledge generation that is necessary to address the extensive unmet information needs of patients, clinicians, administrators, researchers, and health policy makers. This paper explores the ways in which big data can be harnessed to advance prediction, performance, discovery, and comparative effectiveness research to address the complexity of patients, populations, and organizations. Incorporating big data and next-generation analytics into clinical and population health research and practice will require not only new data sources but also new thinking, training, and tools. Adequately used, these reservoirs of data can be a practically inexhaustible source of knowledge to fuel a learning health care system. PMID:25006142

Prediction of household and commercial BMW generation according to socio-economic and other factors for the Dublin region.

PubMed

Purcell, M; Magette, W L

2009-04-01

Both planning and design of integrated municipal solid waste management systems require accurate prediction of waste generation. This research predicted the quantity and distribution of biodegradable municipal waste (BMW) generation within a diverse 'landscape' of residential areas, as well as from a variety of commercial establishments (restaurants, hotels, hospitals, etc.) in the Dublin (Ireland) region. Socio-economic variables, housing types, and the sizes and main activities of commercial establishments were hypothesized as the key determinants contributing to the spatial variability of BMW generation. A geographical information system (GIS) 'model' of BMW generation was created using ArcMap, a component of ArcGIS 9. Statistical data including socio-economic status and household size were mapped on an electoral district basis. Historical research and data from scientific literature were used to assign BMW generation rates to residential and commercial establishments. These predictions were combined to give overall BMW estimates for the region, which can aid waste planning and policy decisions. This technique will also aid the design of future waste management strategies, leading to policy and practice alterations as a function of demographic changes and development. The household prediction technique gave a more accurate overall estimate of household waste generation than did the social class technique. Both techniques produced estimates that differed from the reported local authority data; however, given that local authority reported figures for the region are below the national average, with some of the waste generated from apartment complexes being reported as commercial waste, predictions arising from this research are believed to be closer to actual waste generation than a comparison to reported data would suggest. By changing the input data, this estimation tool can be adapted for use in other locations. Although focusing on waste in the Dublin region, this method of waste prediction can have significant potential benefits if a universal method can be found to apply it effectively.

Testing to Characterize the Advanced Stirling Radioisotope Generator Engineering Unit

NASA Technical Reports Server (NTRS)

Lewandowski, Edward; Schreiber, Jeffrey

2010-01-01

The Advanced Stirling Radioisotope Generator (ASRG), a high efficiency generator, is being considered for space missions. Lockheed Martin designed and fabricated an engineering unit (EU), the ASRG EU, under contract to the Department of Energy. This unit is currently undergoing extended operation testing at the NASA Glenn Research Center to generate performance data and validate life and reliability predictions for the generator and the Stirling convertors. It has also undergone performance tests to characterize generator operation while varying control parameters and system inputs. This paper summarizes and explains test results in the context of designing operating strategies for the generator during a space mission and notes expected differences between the EU performance and future generators.

Development and Preclinical Testing of Laser-Generated Shockwave Therapy for Infected Wounds

NASA Astrophysics Data System (ADS)

Francis, Nathan Craig

The goal of this thesis is to translate laser-generated shockwave (LGS) therapy from a bench-top, research system into a portable, clinical system for in vivo animal trials. Prior research along this topic was completed using a benchtop system, in a physical setup dissimilar to the clinical setup. So the technology required re-engineering in order to apply it to animal studies. This began with the construction of a portable LGS therapy system, mobile enough to transport from laboratory to clinical settings. Included in the portable system is a 2D scanning system to consistently treat wound areas of varying geometries with shockwaves of 3 mm diameter spot sizes. The shockwaves generated by the portable laser system were characterized, along with the varying shockwave-generating substrates possible for clinical application. A final material selection of black polyimide was chosen because of its complete absorption of laser light and its ability to conform to tight wound geometries. Since shockwaves have never been demonstrated to delaminate biofilm from a tissue surface, a proof-of-concept study was completed successfully delaminating Staphylococcus epidermidis from wounded ex vivo pigskin. Through false-colored SEM imaging, biofilm area reduction between treated and non-treated samples were calculated. A 53% reduction in biofilm area and signifcant biofilm fragmentation was seen. An in vivo safety study was conducted next to observe potential physiological effects of LGS on healthy dermal tissue. Treated subjects were observed over a 3 day period, and no physiological or inflammatory effects were seen in the histological analysis. Finally, a pilot wound healing study was com- pleted on excisional wound healing model in rats, with S. epidermidis as the infectious agent, to measure the effect of LGS on wound healing area and rate compared to other treatments. After 9 days of wound healing, no treatment or controls showed a significant difference in wound healing rate or wound area. As a result, LGS also showed no deleterious effects on the tissue which would hinder wound healing. With these results, LGS therapy shows promise as an alternative infected wound treatment, and a system capable of completing thorough animal trials is available for future researchers.

Job and Workload Analysis System for Civil Servants in North Sulawesi Province, Indonesia

NASA Astrophysics Data System (ADS)

Krisnanda, M.; Mewengkang, A.; Rompas, P. T. D.; Togas, P. V.

2018-02-01

This study aims to create automation system to assist sub division of job analysis and workload of North Sulawesi, Indonesia in completing its annual tasks to record all civil servants. The method used in this research is prototyping where a system will be developed according to the revision supplied by the user. The result of this research is a system used to generate reports and calculations based on user filled forms. The result gathered from the interviews, users can make reports faster and easier. Users can also optimise reports on time using the built system.

Advanced Collaborative Environments Supporting Systems Integration and Design

DTIC Science & Technology

2003-03-01

concurrently view a virtual system or product model while maintaining natural, human communication . These virtual systems operate within a computer-generated...These environments allow multiple individuals to concurrently view a virtual system or product model while simultaneously maintaining natural, human ... communication . As a result, TARDEC researchers and system developers are using this advanced high-end visualization technology to develop future

Hawaii | Midmarket Solar Policies in the United States | Solar Research |

Science.gov Websites

net excess generation compensation. Hawaii provides commercial system owners with a 35% tax credit. It of Taxation Commercial system owners are eligible for a tax credit worth 35% of the system's value . The Hawaii tax credit is capped at $500,000 for commercial properties. Solar system owners are also

Air Force Research Laboratory Technology Milestones 2007

DTIC Science & Technology

2007-01-01

Propulsion Fuel Pumps and Fuel Systems Liquid Rockets and Combustion Gas Generators Micropropulsion Gears Monopropellants High-Cycle Fatigue and Its... Systems Electric Propulsion Engine Health Monitoring Systems High-Energy-Density Matter Exhaust Nozzles Injectors and Spray Measurements Fans Laser...of software models to drive development of component-based systems and lightweight domain-specific specification and verification technology. Highly

Using Semantic Web technologies for the generation of domain-specific templates to support clinical study metadata standards.

PubMed

Jiang, Guoqian; Evans, Julie; Endle, Cory M; Solbrig, Harold R; Chute, Christopher G

2016-01-01

The Biomedical Research Integrated Domain Group (BRIDG) model is a formal domain analysis model for protocol-driven biomedical research, and serves as a semantic foundation for application and message development in the standards developing organizations (SDOs). The increasing sophistication and complexity of the BRIDG model requires new approaches to the management and utilization of the underlying semantics to harmonize domain-specific standards. The objective of this study is to develop and evaluate a Semantic Web-based approach that integrates the BRIDG model with ISO 21090 data types to generate domain-specific templates to support clinical study metadata standards development. We developed a template generation and visualization system based on an open source Resource Description Framework (RDF) store backend, a SmartGWT-based web user interface, and a "mind map" based tool for the visualization of generated domain-specific templates. We also developed a RESTful Web Service informed by the Clinical Information Modeling Initiative (CIMI) reference model for access to the generated domain-specific templates. A preliminary usability study is performed and all reviewers (n = 3) had very positive responses for the evaluation questions in terms of the usability and the capability of meeting the system requirements (with the average score of 4.6). Semantic Web technologies provide a scalable infrastructure and have great potential to enable computable semantic interoperability of models in the intersection of health care and clinical research.

Overview of innovative next generation materials for security and defense applications

NASA Astrophysics Data System (ADS)

Taylor, Edward W.; Taylor, Linda R.

2008-10-01

A short technology Overview of recently reported research and development focusing on recent advances in polymer/organic and hybrid-nanotechnology based materials that offer resistance to ionizing and displacement radiations and perhaps which are suitable for transition to next-generation systems is presented. The Overview will focus on new and emerging material technology for the military, first responders, and space systems. Recent material research results and data as well as the potential for diverse applications of these materials to new component developments such as high speed EO polymer modulators and radiation shielding for protection of military and space assets will be discussed. In particular, the ability of several organic/polymer hybrids to self-heal when irradiated by gamma-rays is discussed.

Adequacy assessment of composite generation and transmission systems incorporating wind energy conversion systems

NASA Astrophysics Data System (ADS)

Gao, Yi

The development and utilization of wind energy for satisfying electrical demand has received considerable attention in recent years due to its tremendous environmental, social and economic benefits, together with public support and government incentives. Electric power generation from wind energy behaves quite differently from that of conventional sources. The fundamentally different operating characteristics of wind energy facilities therefore affect power system reliability in a different manner than those of conventional systems. The reliability impact of such a highly variable energy source is an important aspect that must be assessed when the wind power penetration is significant. The focus of the research described in this thesis is on the utilization of state sampling Monte Carlo simulation in wind integrated bulk electric system reliability analysis and the application of these concepts in system planning and decision making. Load forecast uncertainty is an important factor in long range planning and system development. This thesis describes two approximate approaches developed to reduce the number of steps in a load duration curve which includes load forecast uncertainty, and to provide reasonably accurate generating and bulk system reliability index predictions. The developed approaches are illustrated by application to two composite test systems. A method of generating correlated random numbers with uniform distributions and a specified correlation coefficient in the state sampling method is proposed and used to conduct adequacy assessment in generating systems and in bulk electric systems containing correlated wind farms in this thesis. The studies described show that it is possible to use the state sampling Monte Carlo simulation technique to quantitatively assess the reliability implications associated with adding wind power to a composite generation and transmission system including the effects of multiple correlated wind sites. This is an important development as it permits correlated wind farms to be incorporated in large practical system studies without requiring excessive increases in computer solution time. The procedures described in this thesis for creating monthly and seasonal wind farm models should prove useful in situations where time period models are required to incorporate scheduled maintenance of generation and transmission facilities. There is growing interest in combining deterministic considerations with probabilistic assessment in order to evaluate the quantitative system risk and conduct bulk power system planning. A relatively new approach that incorporates deterministic and probabilistic considerations in a single risk assessment framework has been designated as the joint deterministic-probabilistic approach. The research work described in this thesis illustrates that the joint deterministic-probabilistic approach can be effectively used to integrate wind power in bulk electric system planning. The studies described in this thesis show that the application of the joint deterministic-probabilistic method provides more stringent results for a system with wind power than the traditional deterministic N-1 method because the joint deterministic-probabilistic technique is driven by the deterministic N-1 criterion with an added probabilistic perspective which recognizes the power output characteristics of a wind turbine generator.

Dynamic-Type Ice Thermal Storage Systems

NASA Astrophysics Data System (ADS)

Ohira, Akiyoshi

This paper deals with reviews for research and development of a dynamic-type ice thermal storage system. This system has three main features. First, the ice thermal storage tank and the ice generator are separate. Second, ice is transported to the tank from the ice generator by water or air. Third, the ice making and melting processes are operated at the same time. Outlet water temperature from the dynamic-type ice thermal storage tank remains low for a longer time. In this paper, dynamic-Type ice thermal storage systems are divided into three parts: the ice making part, the ice transport part, and the cold energy release part. Each part is reviewed separately.

Why silicon is and will remain the dominant photovoltaic material

NASA Astrophysics Data System (ADS)

Singh, Rajendra

2009-07-01

Rising demands of energy in emerging economies, coupled with the green house gas emissions related problems around the globe have provided a unique opportunity of exploiting the advantages offered by photovoltaic (PV) systems for green energy electricity generation. Similar to cell phones, power generated by PV systems can reach over two billion people worldwide who have no access to clean energy. Only silicon based PV devices meet the low-cost manufacturing criterion of clean energy conversion (abundance of raw material and no environmental health and safety issues). The use of larger size glass substrates and manufacturing techniques similar to the ones used by the liquid crystal display industry and the large scale manufacturing of amorphous silicon thin films based modules (~ GW per year manufacturing at a single location) can lead to installed PV system cost of $3/Wp. This will open a huge market for grid connected PV systems and related markets. With further research and development, this approach can provide $2/Wp installed PV system costs in the next few years. At this cost level, PV electricity generation is competitive with any other technology, and PV power generation can be a dominant electricity generation technology in the 21st century.

Control system design for the MOD-5A 7.3 mW wind turbine generator

NASA Technical Reports Server (NTRS)

Barton, Robert S.; Hosp, Theodore J.; Schanzenbach, George P.

1995-01-01

This paper provides descriptions of the requirements analysis, hardware development and software development phases of the Control System design for the MOD-5A 7.3 mW Wind Turbine Generator. The system, designed by General Electric Company, Advanced Energy Programs Department, under contract DEN 3-153 with NASA Lewis Research Center and DOE, provides real time regulation of rotor speed by control of both generator torque and rotor torque. A variable speed generator system is used to provide both airgap torque control and reactive power control. The wind rotor is designed with segmented ailerons which are positioned to control blade torque. The central component of the control system, selected early in the design process, is a programmable controller used for sequencing, alarm monitoring, communication, and real time control. Development of requirements for use of aileron controlled blades and a variable speed generator required an analytical simulation that combined drivetrain, tower and blade elastic modes with wind disturbances and control behavior. An orderly two phase plan was used for controller software development. A microcomputer based turbine simulator was used to facilitate hardware and software integration and test.

Global renewable energy-based electricity generation and smart grid system for energy security.

PubMed

Islam, M A; Hasanuzzaman, M; Rahim, N A; Nahar, A; Hosenuzzaman, M

2014-01-01

Energy is an indispensable factor for the economic growth and development of a country. Energy consumption is rapidly increasing worldwide. To fulfill this energy demand, alternative energy sources and efficient utilization are being explored. Various sources of renewable energy and their efficient utilization are comprehensively reviewed and presented in this paper. Also the trend in research and development for the technological advancement of energy utilization and smart grid system for future energy security is presented. Results show that renewable energy resources are becoming more prevalent as more electricity generation becomes necessary and could provide half of the total energy demands by 2050. To satisfy the future energy demand, the smart grid system can be used as an efficient system for energy security. The smart grid also delivers significant environmental benefits by conservation and renewable generation integration.

Global Renewable Energy-Based Electricity Generation and Smart Grid System for Energy Security

PubMed Central

Islam, M. A.; Hasanuzzaman, M.; Rahim, N. A.; Nahar, A.; Hosenuzzaman, M.

2014-01-01

Energy is an indispensable factor for the economic growth and development of a country. Energy consumption is rapidly increasing worldwide. To fulfill this energy demand, alternative energy sources and efficient utilization are being explored. Various sources of renewable energy and their efficient utilization are comprehensively reviewed and presented in this paper. Also the trend in research and development for the technological advancement of energy utilization and smart grid system for future energy security is presented. Results show that renewable energy resources are becoming more prevalent as more electricity generation becomes necessary and could provide half of the total energy demands by 2050. To satisfy the future energy demand, the smart grid system can be used as an efficient system for energy security. The smart grid also delivers significant environmental benefits by conservation and renewable generation integration. PMID:25243201

Enhancing Systems Engineering Education Through Case Study Writing

NASA Technical Reports Server (NTRS)

Stevens, Jennifer Stenger

2016-01-01

Developing and refining methods for teaching systems engineering is part of Systems Engineering grand challenges and agenda for research in the SE research community. Retention of systems engineering knowledge is a growing concern in the United States as the baby boom generation continues to retire and the faster pace of technology development does not allow for younger generations to gain experiential knowledge through years of practice. Government agencies, including the National Aeronautics and Space Administration (NASA), develop their own curricula and SE leadership development programs to "grow their own" systems engineers. Marshall Space Flight Center (MSFC) conducts its own Center-focused Marshall Systems Engineering Leadership Development Program (MSELDP), a competitive program consisting of coursework, a guest lecture series, and a rotational assignment into an unfamiliar organization engaged in systems engineering. Independently, MSFC developed two courses to address knowledge retention and sharing concerns: Real World Marshall Mission Success course and its Case Study Writers Workshop and Writers Experience. Teaching case study writing and leading students through a hands-on experience at writing a case study on an SE topic can enhance SE training and has the potential to accelerate the transfer of experiential knowledge. This paper is an overview of the pilot experiences with teaching case study writing, its application in case study-based learning, and identifies potential areas of research and application for case study writing in systems engineering education.

Radar signature generation for feature-aided tracking research

NASA Astrophysics Data System (ADS)

Piatt, Teri L.; Sherwood, John U.; Musick, Stanton H.

2005-05-01

Accurately associating sensor kinematic reports to known tracks, new tracks, or clutter is one of the greatest obstacles to effective track estimation. Feature-aiding is one technology that is emerging to address this problem, and it is expected that adding target features will aid report association by enhancing track accuracy and lengthening track life. The Sensor's Directorate of the Air Force Research Laboratory is sponsoring a challenge problem called Feature-Aided Tracking of Stop-move Objects (FATSO). The long-range goal of this research is to provide a full suite of public data and software to encourage researchers from government, industry, and academia to participate in radar-based feature-aided tracking research. The FATSO program is currently releasing a vehicle database coupled to a radar signature generator. The completed FATSO system will incorporate this database/generator into a Monte Carlo simulation environment for evaluating multiplatform/multitarget tracking scenarios. The currently released data and software contains the following: eight target models, including a tank, ammo hauler, and self-propelled artillery vehicles; and a radar signature generator capable of producing SAR and HRR signatures of all eight modeled targets in almost any configuration or articulation. In addition, the signature generator creates Z-buffer data, label map data, and radar cross-section prediction and allows the user to add noise to an image while varying sensor-target geometry (roll, pitch, yaw, squint). Future capabilities of this signature generator, such as scene models and EO signatures as well as details of the complete FATSO testbed, are outlined.

An Extended IEEE 118-Bus Test System With High Renewable Penetration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pena, Ivonne; Martinez-Anido, Carlo Brancucci; Hodge, Bri-Mathias

This article describes a new publicly available version of the IEEE 118-bus test system, named NREL-118. The database is based on the transmission representation (buses and lines) of the IEEE 118-bus test system, with a reconfigured generation representation using three regions of the US Western Interconnection from the latest Western Electricity Coordination Council (WECC) 2024 Common Case [1]. Time-synchronous hourly load, wind, and solar time series are provided for over one year (8784 hours). The public database presented and described in this manuscript will allow researchers to model a test power system using detailed transmission, generation, load, wind, and solarmore » data. This database includes key additional features that add to the current IEEE 118-bus test model, such as: the inclusion of 10 generation technologies with different heat rate functions, minimum stable levels and ramping rates, GHG emissions rates, regulation and contingency reserves, and hourly time series data for one full year for load, wind and solar generation.« less

An automated synthesis-purification-sample-management platform for the accelerated generation of pharmaceutical candidates.

PubMed

Sutherland, J David; Tu, Noah P; Nemcek, Thomas A; Searle, Philip A; Hochlowski, Jill E; Djuric, Stevan W; Pan, Jeffrey Y

2014-04-01

A flexible and integrated flow-chemistry-synthesis-purification compound-generation and sample-management platform has been developed to accelerate the production of small-molecule organic-compound drug candidates in pharmaceutical research. Central to the integrated system is a Mitsubishi robot, which hands off samples throughout the process to the next station, including synthesis and purification, sample dispensing for purity and quantification analysis, dry-down, and aliquot generation.

Automated real-time software development

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Walker, Carrie K.; Turkovich, John J.

1993-01-01

A Computer-Aided Software Engineering (CASE) system has been developed at the Charles Stark Draper Laboratory (CSDL) under the direction of the NASA Langley Research Center. The CSDL CASE tool provides an automated method of generating source code and hard copy documentation from functional application engineering specifications. The goal is to significantly reduce the cost of developing and maintaining real-time scientific and engineering software while increasing system reliability. This paper describes CSDL CASE and discusses demonstrations that used the tool to automatically generate real-time application code.

[Cell phone communication: hygienic characteristics, biological action, standardization (a review)].

PubMed

Gudina, M V; Volkotrub, L P

2010-01-01

The paper considers the topical issues concerning the functioning of the cellular communication system. It provides the hygienic characteristics of its individual elements. The factors influencing the size of an electromagnetic field generated by mobile phones are stated. Research data on the impact of electromagnetic radiation from a mobile phone on users' health are reviewed. The pivots of present-day Russian hygienic rating regarding the permissible exposures to nonionizing electromagnetic energy generated by the elements of the cellular communication system are identified.

Research Study Towards a MEFFV Electric Armament System

DTIC Science & Technology

2004-01-01

CHPSPerf Inputs Parameter Setting Engine Power (kW) 500 per engine Generator Power (kW) 500/generator Traction Motors Power (kW) 500/side # Battery Pack...Cells in Parallel 2 # Motors in Drive Train 2 Max Power of Traction Motors 200 Minimum Engine Power (kW) 50 Optimum Engine Power (kW) 750 Stop... motors . Other options were examined for the energy storage system. Of particular interest in this regard is the use of the CPA flywheel as the load

GeoChange Global Change Data

USGS Publications Warehouse

,

1997-01-01

GeoChange is an online data system providing access to research results and data generated by the U.S. Geological Survey's Global Change Research Program. Researchers in this program study climate history and the causes of climatic variations, as well as providing baseline data sets on contemporary atmospheric chemistry, high-resolution meteorology, and dust deposition. Research results are packaged as data sets, groups of digital files containing scientific observations, documentation, and interpretation. The data sets are arranged in a consistent manner using standard file formats so that users of a variety of computer systems can access and use them.

Bioethanol from Lignocellulosic Biomass: Current Findings Determine Research Priorities

PubMed Central

Kang, Qian; Appels, Lise; Tan, Tianwei

2014-01-01

“Second generation” bioethanol, with lignocellulose material as feedstock, is a promising alternative for first generation bioethanol. This paper provides an overview of the current status and reveals the bottlenecks that hamper its implementation. The current literature specifies a conversion of biomass to bioethanol of 30 to ~50% only. Novel processes increase the conversion yield to about 92% of the theoretical yield. New combined processes reduce both the number of operational steps and the production of inhibitors. Recent advances in genetically engineered microorganisms are promising for higher alcohol tolerance and conversion efficiency. By combining advanced systems and by intensive additional research to eliminate current bottlenecks, second generation bioethanol could surpass the traditional first generation processes. PMID:25614881

Construction of Blaze at the University of Illinois at Chicago: A Shared, High-Performance, Visual Computer for Next-Generation Cyberinfrastructure-Accelerated Scientific, Engineering, Medical and Public Policy Research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, Maxine D.; Leigh, Jason

2014-02-17

The Blaze high-performance visual computing system serves the high-performance computing research and education needs of University of Illinois at Chicago (UIC). Blaze consists of a state-of-the-art, networked, computer cluster and ultra-high-resolution visualization system called CAVE2(TM) that is currently not available anywhere in Illinois. This system is connected via a high-speed 100-Gigabit network to the State of Illinois' I-WIRE optical network, as well as to national and international high speed networks, such as the Internet2, and the Global Lambda Integrated Facility. This enables Blaze to serve as an on-ramp to national cyberinfrastructure, such as the National Science Foundation’s Blue Waters petascalemore » computer at the National Center for Supercomputing Applications at the University of Illinois at Chicago and the Department of Energy’s Argonne Leadership Computing Facility (ALCF) at Argonne National Laboratory. DOE award # DE-SC005067, leveraged with NSF award #CNS-0959053 for “Development of the Next-Generation CAVE Virtual Environment (NG-CAVE),” enabled us to create a first-of-its-kind high-performance visual computing system. The UIC Electronic Visualization Laboratory (EVL) worked with two U.S. companies to advance their commercial products and maintain U.S. leadership in the global information technology economy. New applications are being enabled with the CAVE2/Blaze visual computing system that is advancing scientific research and education in the U.S. and globally, and help train the next-generation workforce.« less

The Research Consortium on Religious Healthcare Institutions: studying the impact of religious restrictions on women's reproductive health.

PubMed

Freedman, Lori R; Stulberg, Debra B

2016-07-01

Catholic hospitals and other religious institutions are a large and growing part of the US health care system. They have specific policies restricting reproductive health care. Despite increased public attention in the media to women denied necessary pregnancy-related care at Catholic hospitals, research on the effects of religious restrictions remains limited. This article summarizes research priorities as generated by 80 attendees at the inaugural meeting of the Research Consortium on Religious Healthcare Institutions. Such research is need to understand the impact of religious health system ownership on women's health. Copyright © 2016 Elsevier Inc. All rights reserved.

NASA's Solar System Exploration Research Virtual Institute: Combining Science and Exploration

NASA Astrophysics Data System (ADS)

Bailey, B.; Schmidt, G.; Daou, D.; Pendleton, Y.

2015-10-01

The NASA Solar System Exploration Research Virtual Institute (SSERVI) is a virtual institute focused on research at the intersection of science andexploration, training the next generation of lunar scientists, and community development. As part of the SSERVI mission, we act as a hub for opportunities that engage the larger scientific and exploration communities in order to form new interdisciplinary, research-focused collaborations. This talk will describe the research efforts of the nine domestic teams that constitute the U.S. complement of the Institute and how we will engage the international science and exploration communities through workshops, conferences, online seminars and classes, student exchange programs and internships.

Instrumentation and control system for an F-15 stall/spin

NASA Technical Reports Server (NTRS)

Pitts, F. L.; Holmes, D. C. E.; Zaepfel, K. P.

1974-01-01

An instrumentation and control system is described that was used for radio-controlled F-15 airplane model stall/spin research at the NASA-Langley Research Center. This stall/spin research technique, using scale model aircraft, provides information on the post-stall and spin-entry characteristics of full-scale aircraft. The instrumentation described provides measurements of flight parameters such as angle of attack and sideslip, airspeed, control-surface position, and three-axis rotation rates; these data are recorded on an onboard magnetic tape recorder. The proportional radio control system, which utilizes analog potentiometric signals generated from ground-based pilot inputs, and the ground-based system used in the flight operation are also described.

Solar Mirror Fabrication in the Technical Services Building

NASA Image and Video Library

1966-02-21

Daniel Bernatowicz, Chief of the Advanced Power Systems Branch at the National Aeronautics and Space Administration (NASA) Lewis Research Center, examines a 20-foot section of a solar mirror being fabricated in the Jig Bore Room of the Technical Services Building. NASA Lewis was conducting a wide-ranging effort to explore methods of generating electrical power for spacecraft. One method employed a large parabolic mirror to concentrate the sun’s energy. The mirror had to remain rigid and withstand micrometeoroids, but remain light and compact enough to be easily launched. In 1963 Bernatowicz and his researchers undertook a program to design a solar mirror to work with the Brayton cycle system on a space station. The mirror in this photograph was prepared for a conference on Advanced Technology in Space Power Systems held at Lewis in late August 1966. Lewis experts discussed advances with batteries, fuel cells, isotope and thermoelectric generators, and the SNAP-8 space power system. Lewis was developing several types of solar mirrors to work with a Brayton cycle electric generating system. The mirror’s 12 sections were shaped using a unique forming process developed at Lewis, coated with an epoxy, and plated with aluminum. The mirror concentrated the Sun's rays on a heat storage receiver containing lithium fluoride. This material was heated to produce power in a turbogenerator system, while additional heat was stored for use when the unit was in the Earth's shadow.

An optimal design of wind turbine and ship structure based on neuro-response surface method

NASA Astrophysics Data System (ADS)

Lee, Jae-Chul; Shin, Sung-Chul; Kim, Soo-Young

2015-07-01

The geometry of engineering systems affects their performances. For this reason, the shape of engineering systems needs to be optimized in the initial design stage. However, engineering system design problems consist of multi-objective optimization and the performance analysis using commercial code or numerical analysis is generally time-consuming. To solve these problems, many engineers perform the optimization using the approximation model (response surface). The Response Surface Method (RSM) is generally used to predict the system performance in engineering research field, but RSM presents some prediction errors for highly nonlinear systems. The major objective of this research is to establish an optimal design method for multi-objective problems and confirm its applicability. The proposed process is composed of three parts: definition of geometry, generation of response surface, and optimization process. To reduce the time for performance analysis and minimize the prediction errors, the approximation model is generated using the Backpropagation Artificial Neural Network (BPANN) which is considered as Neuro-Response Surface Method (NRSM). The optimization is done for the generated response surface by non-dominated sorting genetic algorithm-II (NSGA-II). Through case studies of marine system and ship structure (substructure of floating offshore wind turbine considering hydrodynamics performances and bulk carrier bottom stiffened panels considering structure performance), we have confirmed the applicability of the proposed method for multi-objective side constraint optimization problems.

Home | Simulation Research

Science.gov Websites

Group specializes in the research, development and deployment of software that support the design and controls design, the Spawn of EnergyPlus next-generation simulation engine, for building and control energy systems tools for OpenBuildingControl to support control design, deployment and verification of building

Performance of a Half-Heusler Thermoelectric Generator for Automotive Application

DOE PAGES

Szybist, James; Davis, Steven; Thomas, John; ...

2018-04-03

Thermoelectric generators (TEGs) have been researched and developed for harvesting energy from otherwise wasted heat. For automotive applications this will most likely involve using internal combustion engine exhaust as the heat source, with the TEG positioned after the catalyst system. Applications to exhaust gas recirculation systems and compressed air coolers have also been suggested. A thermoelectric generator based on half-Heusler thermoelectric materials was developed, engineered, and fabricated, targeting a gasoline passenger sedan application. This generator was installed on a gasoline engine exhaust system in a dynamometer cell, and positioned immediately downstream of the closecoupled three-way catalyst. The generator was characterizedmore » using a matrix of steady-state conditions representing the important portions of the engine map. Detailed performance results are presented. Measurements indicate the generator can produces over 300 W of power with 900 °C exhaust at relatively high flow rates, but less than 50 W when the exhaust is 600 °C and at lower flow rates. The latter condition is typical of standard test cycles and most driving scenarios.« less

Performance of a Half-Heusler Thermoelectric Generator for Automotive Application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szybist, James; Davis, Steven; Thomas, John

Thermoelectric generators (TEGs) have been researched and developed for harvesting energy from otherwise wasted heat. For automotive applications this will most likely involve using internal combustion engine exhaust as the heat source, with the TEG positioned after the catalyst system. Applications to exhaust gas recirculation systems and compressed air coolers have also been suggested. A thermoelectric generator based on half-Heusler thermoelectric materials was developed, engineered, and fabricated, targeting a gasoline passenger sedan application. This generator was installed on a gasoline engine exhaust system in a dynamometer cell, and positioned immediately downstream of the closecoupled three-way catalyst. The generator was characterizedmore » using a matrix of steady-state conditions representing the important portions of the engine map. Detailed performance results are presented. Measurements indicate the generator can produces over 300 W of power with 900 °C exhaust at relatively high flow rates, but less than 50 W when the exhaust is 600 °C and at lower flow rates. The latter condition is typical of standard test cycles and most driving scenarios.« less

Bermuda Triangle or three to tango: generation Y, e-health and knowledge management.

PubMed

Yee, Kwang Chien

2007-01-01

Generation Y workers are slowly gathering critical mass in the healthcare sector. The sustainability of future healthcare is highly dependent on this group of workers. This generation of workers loves technology and thrives in stimulating environments. They have great thirst for life-experience and therefore they move from one working environment to the other. The healthcare system has a hierarchical operational, information and knowledge structure, which unfortunately might not be the ideal ground to integrate with generation Y. The challenges ahead present a fantastic opportunity for electronic health implementation and knowledge management to flourish. Generation Y workers, however, have very different expectation of technology utilisation, technology design and knowledge presentation. This paper will argue that a clear understanding of this group of workers is essential for researchers in health informatics and knowledge management in order to provide socio-technical integrated solution for this group of future workers. The sustainability of a quality healthcare system will depend upon the integration of generation Y, health informatics and knowledge management strategies in a re-invented healthcare system.

Acoustic wave propagation in high-pressure system.

PubMed

Foldyna, Josef; Sitek, Libor; Habán, Vladimír

2006-12-22

Recently, substantial attention is paid to the development of methods of generation of pulsations in high-pressure systems to produce pulsating high-speed water jets. The reason is that the introduction of pulsations into the water jets enables to increase their cutting efficiency due to the fact that the impact pressure (so-called water-hammer pressure) generated by an impact of slug of water on the target material is considerably higher than the stagnation pressure generated by corresponding continuous jet. Special method of pulsating jet generation was developed and tested extensively under the laboratory conditions at the Institute of Geonics in Ostrava. The method is based on the action of acoustic transducer on the pressure liquid and transmission of generated acoustic waves via pressure system to the nozzle. The purpose of the paper is to present results obtained during the research oriented at the determination of acoustic wave propagation in high-pressure system. The final objective of the research is to solve the problem of transmission of acoustic waves through high-pressure water to generate pulsating jet effectively even at larger distances from the acoustic source. In order to be able to simulate numerically acoustic wave propagation in the system, it is necessary among others to determine dependence of the sound speed and second kinematical viscosity on operating pressure. Method of determination of the second kinematical viscosity and speed of sound in liquid using modal analysis of response of the tube filled with liquid to the impact was developed. The response was measured by pressure sensors placed at both ends of the tube. Results obtained and presented in the paper indicate good agreement between experimental data and values of speed of sound calculated from so-called "UNESCO equation". They also show that the value of the second kinematical viscosity of water depends on the pressure.

Overview of Glenn Mechanical Components Branch Research

NASA Astrophysics Data System (ADS)

Zakrajsek, James

2002-09-01

Mr. James Zakrajsek, chief of the Mechanical Components Branch, gave an overview of research conducted by the branch. Branch members perform basic research on mechanical components and systems, including gears and bearings, turbine seals, structural and thermal barrier seals, and space mechanisms. The research is focused on propulsion systems for present and advanced aerospace vehicles. For rotorcraft and conventional aircraft, we conduct research to develop technology needed to enable the design of low noise, ultra safe geared drive systems. We develop and validate analytical models for gear crack propagation, gear dynamics and noise, gear diagnostics, bearing dynamics, and thermal analyses of gear systems using experimental data from various component test rigs. In seal research we develop and test advanced turbine seal concepts to increase efficiency and durability of turbine engines. We perform experimental and analytical research to develop advanced thermal barrier seals and structural seals for current and next generation space vehicles. Our space mechanisms research involves fundamental investigation of lubricants, materials, components and mechanisms for deep space and planetary environments.

An Innovation for the Energy Industry

NASA Technical Reports Server (NTRS)

1985-01-01

REDOX is an economical energy storage system which promises major reductions in the cost of storing electrical energy. The system is based upon the conversion of chemical energy into electrical energy. 75 percent of the energy used to charge the system is returned. It is flexible and the energy may be stored for long periods. It was developed by Lewis Research Center, who transferred the technology to SOHIO for further development and possible commercialization. Redox could eliminate the use of high quality generator levels and would be particularly valuable to utilities which generate power from coal or nuclear energy.

Lyapunov Orbits in the Jupiter System Using Electrodynamic Tethers

NASA Technical Reports Server (NTRS)

Bokelmann, Kevin; Russell, Ryan P.; Lantoine, Gregory

2013-01-01

Various researchers have proposed the use of electrodynamic tethers for power generation and capture from interplanetary transfers. The effect of tether forces on periodic orbits in Jupiter-satellite systems are investigated. A perturbation force is added to the restricted three-body problem model and a series of simplifications allows development of a conservative system that retains the Jacobi integral. Expressions are developed to find modified locations of equilibrium positions. Modified families of Lyapunov orbits are generated as functions of tether size and Jacobi integral. Zero velocity curves and stability analyses are used to evaluate the dynamical properties of tether-modified orbits.

Sense, decide, act, communicate (SDAC): next generation of smart sensor systems

NASA Astrophysics Data System (ADS)

Berry, Nina; Davis, Jesse; Ko, Teresa H.; Kyker, Ron; Pate, Ron; Stark, Doug; Stinnett, Regan; Baker, James; Cushner, Adam; Van Dyke, Colin; Kyckelhahn, Brian

2004-09-01

The recent war on terrorism and increased urban warfare has been a major catalysis for increased interest in the development of disposable unattended wireless ground sensors. While the application of these sensors to hostile domains has been generally governed by specific tasks, this research explores a unique paradigm capitalizing on the fundamental functionality related to sensor systems. This functionality includes a sensors ability to Sense - multi-modal sensing of environmental events, Decide - smart analysis of sensor data, Act - response to environmental events, and Communication - internal to system and external to humans (SDAC). The main concept behind SDAC sensor systems is to integrate the hardware, software, and networking to generate 'knowledge and not just data'. This research explores the usage of wireless SDAC units to collectively make up a sensor system capable of persistent, adaptive, and autonomous behavior. These systems are base on the evaluation of scenarios and existing systems covering various domains. This paper presents a promising view of sensor network characteristics, which will eventually yield smart (intelligent collectives) network arrays of SDAC sensing units generally applicable to multiple related domains. This paper will also discuss and evaluate the demonstration system developed to test the concepts related to SDAC systems.

Funder Report on Decision Support Systems Project Dissemination Activities, Fiscal Year 1985.

ERIC Educational Resources Information Center

Tetlow, William L.

Dissemination activities for the Decision Support Systems (DSS) for fiscal year (FY) 1985 are reported by the National Center for Higher Education Management Systems (NCHEMS). The main means for disseminating results of the DSS research and development project has been through computer-generated video presentations at meetings of higher education…

Towards Next Generation Activity-Based Learning Systems

ERIC Educational Resources Information Center

Sampson, Demetrios G.; Karampiperis, Pythagoras

2006-01-01

The need for e-learning systems that support a diverse set of pedagogical requirements has been identified as an important issue in web-based education. Until now, significant research and development effort has been devoted to aiming towards web-based educational systems tailored to specific pedagogical approaches. The most advanced of them are…

Energy Systems Integration News | Energy Systems Integration Facility |

Science.gov Websites

Renewable Generation Integration Study (ERGIS), looks ahead to the year 2026 and examines how the Eastern accurately modeling the entire system at five-minute intervals for an entire year has never even been Integrated Network Testbed for Energy Grid Research and Technology Experimentation (INTEGRATE) project, up to

The Biological and Chemical Oceanography Data Management Office

NASA Astrophysics Data System (ADS)

Allison, M. D.; Chandler, C. L.; Groman, R. C.; Wiebe, P. H.; Glover, D. M.; Gegg, S. R.

2011-12-01

Oceanography and marine ecosystem research are inherently interdisciplinary fields of study that generate and require access to a wide variety of measurements. In late 2006 the Biological and Chemical Oceanography Sections of the National Science Foundation (NSF) Geosciences Directorate Division of Ocean Sciences (OCE) funded the Biological and Chemical Oceanography Data Management Office (BCO-DMO). In late 2010 additional funding was contributed to support management of research data from the NSF Office of Polar Programs Antarctic Organisms & Ecosystems Program. The BCO-DMO is recognized in the 2011 Division of Ocean Sciences Sample and Data Policy as one of several program specific data offices that support NSF OCE funded researchers. BCO-DMO staff members offer data management support throughout the project life cycle to investigators from large national programs and medium-sized collaborative research projects, as well as researchers from single investigator awards. The office manages and serves all types of oceanographic data and information generated during the research process and contributed by the originating investigators. BCO-DMO has built a data system that includes the legacy data from several large ocean research programs (e.g. United States Joint Global Ocean Flux Study and United States GLOBal Ocean ECosystems Dynamics), to which data have been contributed from recently granted NSF OCE and OPP awards. The BCO-DMO data system can accommodate many different types of data including: in situ and experimental biological, chemical, and physical measurements; modeling results and synthesis data products. The system enables reuse of oceanographic data for new research endeavors, supports synthesis and modeling activities, provides availability of "real data" for K-12 and college level use, and provides decision-support field data for policy-relevant investigations. We will present an overview of the data management system capabilities including: map-based and text-based data discovery and access systems; recent enhancements to data search tools; data export and download utilities; and strategic use of controlled vocabularies to facilitate data integration and to improve data system interoperability.

Effect of accuracy of wind power prediction on power system operator

NASA Technical Reports Server (NTRS)

Schlueter, R. A.; Sigari, G.; Costi, T.

1985-01-01

This research project proposed a modified unit commitment that schedules connection and disconnection of generating units in response to load. A modified generation control is also proposed that controls steam units under automatic generation control, fast responding diesels, gas turbines and hydro units under a feedforward control, and wind turbine array output under a closed loop array control. This modified generation control and unit commitment require prediction of trend wind power variation one hour ahead and the prediction of error in this trend wind power prediction one half hour ahead. An improved meter for predicting trend wind speed variation is developed. Methods for accurately simulating the wind array power from a limited number of wind speed prediction records was developed. Finally, two methods for predicting the error in the trend wind power prediction were developed. This research provides a foundation for testing and evaluating the modified unit commitment and generation control that was developed to maintain operating reliability at a greatly reduced overall production cost for utilities with wind generation capacity.

Development of closed loop roll control for magnetic balance systems

NASA Technical Reports Server (NTRS)

Covert, E. E.; Haldeman, C. W.; Ramohalli, G.; Way, P.

1982-01-01

This research was undertaken with the goal of demonstrating closed loop control of the roll degree of freedom on the NASA prototype magnetic suspension and balance system at the MIT Aerophysics Laboratory, thus, showing feasibility for a roll control system for any large magnetic balance system which might be built in the future. During the research under this grant, study was directed toward the several areas of torque generation, position sensing, model construction and control system design. These effects were then integrated to produce successful closed loop operation of the analogue roll control system. This experience indicated the desirability of microprocessor control for the angular degrees of freedom.

The function of the earth observing system - Data information system Distributed Active Archive Centers

NASA Technical Reports Server (NTRS)

Lapenta, C. C.

1992-01-01

The functionality of the Distributed Active Archive Centers (DAACs) which are significant elements of the Earth Observing System Data and Information System (EOSDIS) is discussed. Each DAAC encompasses the information management system, the data archival and distribution system, and the product generation system. The EOSDIS DAACs are expected to improve the access to earth science data set needed for global change research.

Dynamic Test Bed Analysis of Gas Energy Balance for a Diesel Exhaust System Fit with a Thermoelectric Generator

NASA Astrophysics Data System (ADS)

Fuc, Pawel; Lijewski, Piotr; Ziolkowski, Andrzej; Dobrzyński, Michal

2017-05-01

Analysis of the energy balance for an exhaust system of a diesel engine fit with an automotive thermoelectric generator (ATEG) of our own design has been carried out. A special measurement system and dedicated software were developed to measure the power generated by the modules. The research object was a 1.3-l small diesel engine with power output of 66 kW. The tests were carried out on a dynamic engine test bed that allows reproduction of an actual driving cycle expressed as a function V = f( t), simulating drivetrain (clutch, transmission) operating characteristics, vehicle geometrical parameters, and driver behavior. Measurements of exhaust gas thermodynamic parameters (temperature, pressure, and mass flow) as well as the voltage and current generated by the thermoelectric modules were performed during tests of our own design. Based on the results obtained, the flow of exhaust gas energy in the entire exhaust system was determined along with the ATEG power output. The ideal area of the exhaust system for location of the ATEG was defined to ensure the highest thermal energy recovery efficiency.

Kansas | Solar Research | NREL

Science.gov Websites

1.1 MW. Kansas allows up to 100 kW of solar PV projects to be net metered. Midmarket customer Kansas's RPS. The utility and the customer-generator may sell any associated Renewable Energy Certificates aggregation: Not addressed As an alternative to net metering, customer-generators of systems up to 200 kW may

Russian Education in the Context of the Third Generation Universities' Discourse: Employers' Evaluation

ERIC Educational Resources Information Center

Maximova, Olga; Belyaev, Vladimir; Laukart-Gorbacheva, Olga; Nagmatullina, Lyudmila; Hamzina, Guzel

2016-01-01

Urgent problems of modernization of the Russian system of higher education in the context of the discourse of the third generation universities were revealed on the basis of the expert survey of employers (heads of personnel departments of large industrial enterprises of the city of Kazan and the Republic of Tatarstan) within research project…

Overview of NASA Finesse (Field Investigations to Enable Solar System Science and Exploration) Science and Exploration Project

NASA Technical Reports Server (NTRS)

Heldmann, J. L.; Lim, D.S.S.; Hughes, S.; Nawotniak, S. Kobs; Garry, B.; Sears, D.; Neish, C.; Osinski, G. R.; Hodges, K.; Downs, M.;

Automated documentation generator for advanced protein crystal growth

NASA Technical Reports Server (NTRS)

Maddux, Gary A.; Provancha, Anna; Chattam, David; Ford, Ronald

1993-01-01

The System Management and Production Laboratory at the Research Institute, the University of Alabama in Huntsville (UAH), was tasked by the Microgravity Experiment Projects (MEP) Office of the Payload Projects Office (PPO) at Marshall Space Flight Center (MSFC) to conduct research in the current methods of written documentation control and retrieval. The goals of this research were to determine the logical interrelationships within selected NASA documentation, and to expand on a previously developed prototype system to deliver a distributable, electronic knowledge-based system. This computer application would then be used to provide a paperless interface between the appropriate parties for the required NASA document.

Genetic engineering in Cowpea (Vigna unguiculata): history, status and prospects.

PubMed

Citadin, Cristiane T; Ibrahim, Abdulrazak B; Aragão, Francisco J L

2011-01-01

In the last three decades, a number of attempts have been made to develop reproducible protocols for generating transgenic cowpea that permit the expression of genes of agronomic importance. Pioneer works focused on the development of such systems vis-à-vis an in vitro culture system that would guarantee de novo regeneration of transgenic cowpea arising from cells amenable to one form of gene delivery system or another, but any such system has eluded researchers over the years. Despite this apparent failure, significant progress has been made in generating transgenic cowpea, bringing researchers much nearer to their goal than thirty years ago. Now, various researchers have successfully established transgenic procedures for cowpea with evidence of inherent transgenes of interest, effected by progenies in a Mendelian fashion. New opportunities have thus emerged to optimize existing protocols and devise new strategies to ensure the development of transgenic cowpea with desirable agronomic traits. This review chronicles the important milestones in the last thirty years that have marked the evolution of genetic engineering of cowpea. It also highlights the progress made and describes new strategies that have arisen, culminating in the current status of transgenic technologies for cowpea.

CFD research and systems in Kawasaki Heavy Industries and its future prospects

NASA Astrophysics Data System (ADS)

Hiraoka, Koichi

1990-09-01

KHI Computational Fluid Dynamics (CFD) system is composed of VP100 computer and 2-D and 3-D Euler and/or Navier-Stokes (NS) analysis softwares. For KHI, this system has become a very powerful aerodynamic tool together with the Kawasaki 1 m Transonic Wind Tunnel. The 2-D Euler/NS software, developed in-house, is fully automated, requires no special skill, and was successfully applied to the design of YXX high lift devices and SST supersonic inlet, etc. The 3-D Euler/NS software, developed under joint research with NAL, has an interactively operated Multi-Block type grid generator and can effectively generate grids around complex airplane shapes. Due to the main memory size limitation, 3-D analysis of relatively simple shape, such as SST wing-body, was computed in-house on VP100, otherwise, such as detailed 3-D analyses of ASUKA and HOPE, were computed on NAL VP400, which is 10 times more powerful than VP100, under KHI-NAL joint research. These analysis results have very good correlation with experimental results. However, the present CFD system is less productive than wind tunnel and has applicability limitations.

An optimal design of coreless direct-drive axial flux permanent magnet generator for wind turbine

NASA Astrophysics Data System (ADS)

Ahmed, D.; Ahmad, A.

2013-06-01

Different types of generators are currently being used in wind power technology. The commonly used are induction generator (IG), doubly-fed induction generator (DFIG), electrically excited synchronous generator (EESG) and permanent magnet synchronous generator (PMSG). However, the use of PMSG is rapidly increasing because of advantages such as higher power density, better controllability and higher reliability. This paper presents an innovative design of a low-speed modular, direct-drive axial flux permanent magnet (AFPM) generator with coreless stator and rotor for a wind turbine power generation system that is developed using mathematical and analytical methods. This innovative design is implemented in MATLAB / Simulink environment using dynamic modelling techniques. The main focus of this research is to improve efficiency of the wind power generation system by investigating electromagnetic and structural features of AFPM generator during its operation in wind turbine. The design is validated by comparing its performance with standard models of existing wind power generators. The comparison results demonstrate that the proposed model for the wind power generator exhibits number of advantages such as improved efficiency with variable speed operation, higher energy yield, lighter weight and better wind power utilization.

External Group Coaching and Mentoring: Building a Research Community of Practice at a University of Technology

ERIC Educational Resources Information Center

Maritz, Jeanette; Visagie, Retha; Johnson, Bernadette

2013-01-01

Globally, a clarion call has been made for higher education institutions to establish creative and effective research capacity-building systems with the purpose of developing a next generation of scholars. The training and skills development of a researcher entail a process of increasing levels of participation in diverse communities of practice.…

SSERVI: Merging Science and Human Exploration

NASA Technical Reports Server (NTRS)

Schmidt, Gregory; Gibbs, Kristina

2017-01-01

The NASA Solar System Exploration Research Virtual Institute (SSERVI) is a virtual institute focused on research and the intersection of science and exploration, training the next generation of lunar scientists, and community development. As part of the SSERVI mission, we act as a hub for the opportunities that engage the larger scientific and exploration communities in order to form a new interdisciplinary, research-focused collaborations.

Federal Research and Development Funding: FY2010

DTIC Science & Technology

2009-11-23

represent the more research-oriented part of the RDT&E program. Budget activities 6.4 and 6.5 focus on the development of specific weapon systems or...to fund developmental testing of the BioWatch Generation 3 biological agent detection system. The Administration requested these funds for the...Acquisition, and Operations 800 826 825 844 856 Border and Maritime 33 40 40 40 44 Chemical and Biological 200 207 222 207 207 Command, Control, and

Roadmap for the Hypersonics Programs of the Department of Defense

DTIC Science & Technology

2008-02-01

development and integration of a 1MW e-bean system to provide the necessary energy into the wind tunnel flow field to enable longer duration experiments at...acquired. Finally, “Test and Evaluation” (T&E) is defined as tests and experiments in support of research development and acquisition of systems...Research Experimentation (HIFiRE) project, the DARPA/AF Falcon program, and the DoD Next Generation Launch planning activities. 13 Joint

Performance Evaluation of a Prototype Underwater Short-Range Acoustic Telemetry Modem

DTIC Science & Technology

2010-09-01

SR560 Low-Noise Preamplifier – Hewlett Packard (HP) 3314A Function Generator – Phillips PM 3384 Oscilloscope – Dell Latitude D620 notebook...two Stanford Research Systems SR560 low-noise preamplifiers , an IOtech Personal DAQ/3000 Series data acquisition box (DAQ), an HP 3314A function...mono frequency measurements were two B&K 8103 hydrophones, two Stanford Research Systems SR560 low-noise preamplifiers , an IOtech Personal DAQ/3000

Fuels research studies at NASA Lewis

NASA Technical Reports Server (NTRS)

Antoine, A. C.

1982-01-01

Fuels research studies carried out in a variety of areas related to aviation propulsion, ground transportation, and stationary power generation systems are discussed. The major efforts are directed to studies on fuels for jet aircraft. These studies involve fuels preparation, fuels analysis, and fuel quality evaluations. The scope and direction of research activities in these areas is discussed, descriptions of Lewis capabilities and facilities given, and results of recent research efforts reported.

Butterfly genomics eclosing.

PubMed

Beldade, P; McMillan, W O; Papanicolaou, A

2008-02-01

Technological and conceptual advances of the last decade have led to an explosion of genomic data and the emergence of new research avenues. Evolutionary and ecological functional genomics, with its focus on the genes that affect ecological success and adaptation in natural populations, benefits immensely from a phylogenetically widespread sampling of biological patterns and processes. Among those organisms outside established model systems, butterflies offer exceptional opportunities for multidisciplinary research on the processes generating and maintaining variation in ecologically relevant traits. Here we highlight research on wing color pattern variation in two groups of Nymphalid butterflies, the African species Bicyclus anynana (subfamily Satyrinae) and species of the South American genus Heliconius (subfamily Heliconiinae), which are emerging as important systems for studying the nature and origins of functional diversity. Growing genomic resources including genomic and cDNA libraries, dense genetic maps, high-density gene arrays, and genetic transformation techniques are extending current gene mapping and expression profiling analysis and enabling the next generation of research questions linking genes, development, form, and fitness. Efforts to develop such resources in Bicyclus and Heliconius underscore the general challenges facing the larger research community and highlight the need for a community-wide effort to extend ongoing functional genomic research on butterflies.

A System for Natural Language Sentence Generation.

ERIC Educational Resources Information Center

Levison, Michael; Lessard, Gregory

1992-01-01

Describes the natural language computer program, "Vinci." Explains that using an attribute grammar formalism, Vinci can simulate components of several current linguistic theories. Considers the design of the system and its applications in linguistic modelling and second language acquisition research. Notes Vinci's uses in linguistics…

Basic and applied research related to the technology of space energy conversion systems, 1982 - 1983

NASA Technical Reports Server (NTRS)

Hertzberg, A.

1983-01-01

Topics on solar energy conversion concepts and applications are discussed. An overview of the current status and future utilization of radiation receivers for electrical energy generation, liquid droplet radiation systems, and liquid droplet heat exchangers is presented.

Visualizing Cloud Properties and Satellite Imagery: A Tool for Visualization and Information Integration

NASA Astrophysics Data System (ADS)

Chee, T.; Nguyen, L.; Smith, W. L., Jr.; Spangenberg, D.; Palikonda, R.; Bedka, K. M.; Minnis, P.; Thieman, M. M.; Nordeen, M.

2017-12-01

Providing public access to research products including cloud macro and microphysical properties and satellite imagery are a key concern for the NASA Langley Research Center Cloud and Radiation Group. This work describes a web based visualization tool and API that allows end users to easily create customized cloud product and satellite imagery, ground site data and satellite ground track information that is generated dynamically. The tool has two uses, one to visualize the dynamically created imagery and the other to provide access to the dynamically generated imagery directly at a later time. Internally, we leverage our practical experience with large, scalable application practices to develop a system that has the largest potential for scalability as well as the ability to be deployed on the cloud to accommodate scalability issues. We build upon NASA Langley Cloud and Radiation Group's experience with making real-time and historical satellite cloud product information, satellite imagery, ground site data and satellite track information accessible and easily searchable. This tool is the culmination of our prior experience with dynamic imagery generation and provides a way to build a "mash-up" of dynamically generated imagery and related kinds of information that are visualized together to add value to disparate but related information. In support of NASA strategic goals, our group aims to make as much scientific knowledge, observations and products available to the citizen science, research and interested communities as well as for automated systems to acquire the same information for data mining or other analytic purposes. This tool and the underlying API's provide a valuable research tool to a wide audience both as a standalone research tool and also as an easily accessed data source that can easily be mined or used with existing tools.

Modeling human development in 3D culture.

PubMed

Ader, Marius; Tanaka, Elly M

2014-12-01

Recently human embryonic stem cell research has taken on a new dimension - the third dimension. Capitalizing on increasing knowledge on directing pluripotent cells along different lineages, combined with ECM supported three-dimensional culture conditions, it has become possible to generate highly organized tissues of the central nervous system, gut, liver and kidney. Each system has been used to study different aspects of organogenesis and function including physical forces underlying optic cup morphogenesis, the function of disease related genes in progenitor cell control, as well as interaction of the generated tissues with host tissue upon transplantation. Pluripotent stem cell derived organoids represent powerful systems for the study of how cells self-organize to generate tissues with a given shape, pattern and form. Copyright © 2014 Elsevier Ltd. All rights reserved.

NASA's Next Generation Launch Technology Program - Strategy and Plans

NASA Technical Reports Server (NTRS)

Hueter, Uwe

2003-01-01

The National Aeronautics and Space Administration established a new program office, Next Generation Launch Technology (NGLT) Program Office, last year to pursue technologies for future space launch systems. NGLT will fund research in key technology areas such as propulsion, launch vehicles, operations and system analyses. NGLT is part of NASA s Integrated Space Technology Plan. The NGLT Program is sponsored by NASA s Office of Aerospace Technology and is part of the Space Launch Initiative theme that includes both NGLT and Orbital Space Plane. NGLT will focus on technology development to increase safety and reliability and reduce overall costs associated with building, flying and maintaining the nation s next-generations of space launch vehicles. These investments will be guided by systems engineering and analysis with a focus on the needs of National customers.

Smart grid technologies in local electric grids

NASA Astrophysics Data System (ADS)

Lezhniuk, Petro D.; Pijarski, Paweł; Buslavets, Olga A.

2017-08-01

The research is devoted to the creation of favorable conditions for the integration of renewable sources of energy into electric grids, which were designed to be supplied from centralized generation at large electric power stations. Development of distributed generation in electric grids influences the conditions of their operation - conflict of interests arises. The possibility of optimal functioning of electric grids and renewable sources of energy, when complex criterion of the optimality is balance reliability of electric energy in local electric system and minimum losses of electric energy in it. Multilevel automated system for power flows control in electric grids by means of change of distributed generation of power is developed. Optimization of power flows is performed by local systems of automatic control of small hydropower stations and, if possible, solar power plants.

Optimized Temporal Monitors for SystemC

NASA Technical Reports Server (NTRS)

Tabakov, Deian; Rozier, Kristin Y.; Vardi, Moshe Y.

2012-01-01

SystemC is a modeling language built as an extension of C++. Its growing popularity and the increasing complexity of designs have motivated research efforts aimed at the verification of SystemC models using assertion-based verification (ABV), where the designer asserts properties that capture the design intent in a formal language such as PSL or SVA. The model then can be verified against the properties using runtime or formal verification techniques. In this paper we focus on automated generation of runtime monitors from temporal properties. Our focus is on minimizing runtime overhead, rather than monitor size or monitor-generation time. We identify four issues in monitor generation: state minimization, alphabet representation, alphabet minimization, and monitor encoding. We conduct extensive experimentation and identify a combination of settings that offers the best performance in terms of runtime overhead.

Involving the public through participatory visual research methods

PubMed Central

Lorenz, Laura S.; Kolb, Bettina

2009-01-01

Abstract Objectives  To show how providing cameras to patients and community residents can be effective at involving the public in generating understanding of consumer, community, and health system problems and strengths. Background  Health‐care institutions and systems may seek to include consumer perspectives on health and health care yet be challenged to involve the most vulnerable sectors, be they persons with disabilities or persons with low socio‐economic status living in societies where a top‐down approach to policy is the norm. Methods  Drawing on study examples using photo‐elicitation and photovoice in Morocco and the United States, the authors explore issues of planning, data analysis, ethical concerns and action related to using participatory visual methods in different cultural and political contexts. Results  Visual data generated by consumers can be surprising and can identify health system problems and strengths omitted from data gathered using other means. Statistical data may convince policy makers of the need to address a problem. Participant visual data may in turn encourage policy maker attention and action. Conclusion  Health system decision making may be improved by having a broader range of data available. Participant‐generated visual data may support data gathered using traditional methods, or provide a reality check when compared with data generated by organizations, researchers and policy makers. The two study examples model innovative ways to surface health and health‐care issues as they relate to consumers’ real lives and engage vulnerable groups in systems change, even in contexts where expressing opinions might be seen as a risky thing to do. PMID:19754690

Advanced microgrid design and analysis for forward operating bases

NASA Astrophysics Data System (ADS)

Reasoner, Jonathan

This thesis takes a holistic approach in creating an improved electric power generation system for a forward operating base (FOB) in the future through the design of an isolated microgrid. After an extensive literature search, this thesis found a need for drastic improvement of the FOB power system. A thorough design process analyzed FOB demand, researched demand side management improvements, evaluated various generation sources and energy storage options, and performed a HOMERRTM discrete optimization to determine the best microgrid design. Further sensitivity analysis was performed to see how changing parameters would affect the outcome. Lastly, this research also looks at some of the challenges which are associated with incorporating a design which relies heavily on inverter-based generation sources, and gives possible solutions to help make a renewable energy powered microgrid a reality. While this thesis uses a FOB as the case study, the process and discussion can be adapted to aide in the design of an off-grid small-scale power grid which utilizes high-penetration levels of renewable energy.

Investigation of ionospheric disturbances and associated diagnostic techniques. Final report, 1 January 1992-31 December 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duncan, L.M.

1995-12-12

The objectives of this research and development program were to conduct simulation modeling of the generation and propagation of atmospheric acoustic signals associated with surface and subsurface ground disturbances; to construct an experimental measurement system for exploratory research studies of acoustic generated ionospheric disturbances; to model high power radio wave propagation through the ionosphere, including nonlinear wave plasma interaction effects; and to assist in the assessment of diagnostic systems for observation of ionospheric modification experiments using existing and planned high latitude high power RF transmitting facilities. A computer simulation of ionospheric response to ground launched acoustic pulses was constructed andmore » results compared to observational data associated with HF and incoherent scatter radar measurements of ionospheric effects produced by earthquakes and ground level explosions. These results were then utilized to help define the design, construct and test for an HF Doppler radar system. In addition, an assessment was conducted of ionospheric diagnostic instruments proposed for the Air Force/Navy High Frequency Active Auroral Research Program (HAARP).« less

Emissivity of Candidate Materials for VHTR Applicationbs: Role of Oxidation and Surface Modification Treatments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sridharan, Kumar; Allen, Todd; Anderson, Mark

The Generation IV (GEN IV) Nuclear Energy Systems Initiative was instituted by the Department of Energy (DOE) with the goal of researching and developing technologies and materials necessary for various types of future reactors. These GEN IV reactors will employ advanced fuel cycles, passive safety systems, and other innovative systems, leading to significant differences between these future reactors and current water-cooled reactors. The leading candidate for the Next Generation Nuclear Plant (NGNP) to be built at Idaho National Lab (INL) in the United States is the Very High Temperature Reactor (VHTR). Due to the high operating temperatures of the VHTR,more » the Reactor Pressure Vessel (RPV) will partially rely on heat transfer by radiation for cooling. Heat expulsion by radiation will become all the more important during high temperature excursions during off-normal accident scenarios. Radiant power is dictated by emissivity, a material property. The NGNP Materials Research and Development Program Plan [1] has identified emissivity and the effects of high temperature oxide formation on emissivity as an area of research towards the development of the VHTR.« less

Teacher education in the generative virtual classroom: developing learning theories through a web-delivered, technology-and-science education context

NASA Astrophysics Data System (ADS)

Schaverien, Lynette

2003-12-01

This paper reports the use of a research-based, web-delivered, technology-and-science education context (the Generative Virtual Classroom) in which student-teachers can develop their ability to recognize, describe, analyse and theorize learning. Addressing well-recognized concerns about narrowly conceived, anachronistic and ineffective technology-and-science education, this e-learning environment aims to use advanced technologies for learning, to bring about larger scale improvement in classroom practice than has so far been effected by direct intervention through teacher education. Student-teachers' short, intensive engagement with the Generative Virtual Classroom during their practice teaching is examined. Findings affirm the worth of this research-based e-learning system for teacher education and the power of a biologically based, generative theory to make sense of the learning that occurred.

Teaching about Complex Systems Is No Simple Matter: Building Effective Professional Development for Computer-Supported Complex Systems Instruction

ERIC Educational Resources Information Center

Yoon, Susan A.; Anderson, Emma; Koehler-Yom, Jessica; Evans, Chad; Park, Miyoung; Sheldon, Josh; Schoenfeld, Ilana; Wendel, Daniel; Scheintaub, Hal; Klopfer, Eric

2017-01-01

The recent next generation science standards in the United States have emphasized learning about complex systems as a core feature of science learning. Over the past 15 years, a number of educational tools and theories have been investigated to help students learn about complex systems; but surprisingly, little research has been devoted to…

Development and Application of an Integrated Approach toward NASA Airspace Systems Research

NASA Technical Reports Server (NTRS)

Barhydt, Richard; Fong, Robert K.; Abramson, Paul D.; Koenke, Ed

2008-01-01

The National Aeronautics and Space Administration's (NASA) Airspace Systems Program is contributing air traffic management research in support of the 2025 Next Generation Air Transportation System (NextGen). Contributions support research and development needs provided by the interagency Joint Planning and Development Office (JPDO). These needs generally call for integrated technical solutions that improve system-level performance and work effectively across multiple domains and planning time horizons. In response, the Airspace Systems Program is pursuing an integrated research approach and has adapted systems engineering best practices for application in a research environment. Systems engineering methods aim to enable researchers to methodically compare different technical approaches, consider system-level performance, and develop compatible solutions. Systems engineering activities are performed iteratively as the research matures. Products of this approach include a demand and needs analysis, system-level descriptions focusing on NASA research contributions, system assessment and design studies, and common systemlevel metrics, scenarios, and assumptions. Results from the first systems engineering iteration include a preliminary demand and needs analysis; a functional modeling tool; and initial system-level metrics, scenario characteristics, and assumptions. Demand and needs analysis results suggest that several advanced concepts can mitigate demand/capacity imbalances for NextGen, but fall short of enabling three-times current-day capacity at the nation s busiest airports and airspace. Current activities are focusing on standardizing metrics, scenarios, and assumptions, conducting system-level performance assessments of integrated research solutions, and exploring key system design interfaces.

Research on a power management system for thermoelectric generators to drive wireless sensors on a spindle unit.

PubMed

Li, Sheng; Yao, Xinhua; Fu, Jianzhong

2014-07-16

Thermoelectric energy harvesting is emerging as a promising alternative energy source to drive wireless sensors in mechanical systems. Typically, the waste heat from spindle units in machine tools creates potential for thermoelectric generation. However, the problem of low and fluctuant ambient temperature differences in spindle units limits the application of thermoelectric generation to drive a wireless sensor. This study is devoted to presenting a transformer-based power management system and its associated control strategy to make the wireless sensor work stably at different speeds of the spindle. The charging/discharging time of capacitors is optimized through this energy-harvesting strategy. A rotating spindle platform is set up to test the performance of the power management system at different speeds. The experimental results show that a longer sampling cycle time will increase the stability of the wireless sensor. The experiments also prove that utilizing the optimal time can make the power management system work more effectively compared with other systems using the same sample cycle.

Research on a Power Management System for Thermoelectric Generators to Drive Wireless Sensors on a Spindle Unit

PubMed Central

Li, Sheng; Yao, Xinhua; Fu, Jianzhong

2014-01-01

Thermoelectric energy harvesting is emerging as a promising alternative energy source to drive wireless sensors in mechanical systems. Typically, the waste heat from spindle units in machine tools creates potential for thermoelectric generation. However, the problem of low and fluctuant ambient temperature differences in spindle units limits the application of thermoelectric generation to drive a wireless sensor. This study is devoted to presenting a transformer-based power management system and its associated control strategy to make the wireless sensor work stably at different speeds of the spindle. The charging/discharging time of capacitors is optimized through this energy-harvesting strategy. A rotating spindle platform is set up to test the performance of the power management system at different speeds. The experimental results show that a longer sampling cycle time will increase the stability of the wireless sensor. The experiments also prove that utilizing the optimal time can make the power management system work more effectively compared with other systems using the same sample cycle. PMID:25033189

Crystal growth and materials research in photovoltaics: progress and challenges

NASA Astrophysics Data System (ADS)

Surek, Thomas

2005-02-01

Photovoltaics (PV) is solar electric power—a semiconductor-based technology that converts sunlight to electricity. Three decades of research has led to the discovery of new materials and devices and new processing techniques for low-cost manufacturing. This has resulted in improved sunlight-to-electricity conversion efficiencies, improved outdoor reliability, and lower module and system costs. The manufacture and sale of PV has grown into a $5 billion industry worldwide, with more than 740 megawatts of PV modules shipped in 2003. This paper reviews the significant progress that has occurred in PV materials and devices research over the past 30 years, focusing on the advances in crystal growth and materials research, and examines the challenges to reaching the ultimate potential of current-generation (crystalline silicon), next-generation (thin films and concentrators), and future-generation PV technologies. The latter includes innovative materials and device concepts that hold the promise of significantly higher conversion efficiencies and/or much lower costs.

Trial Maneuver Generation and Selection in the Paladin Tactical Decision Generation System

NASA Technical Reports Server (NTRS)

Chappell, Alan R.; McManus, John W.; Goodrich, Kenneth H.

1992-01-01

To date, increased levels of maneuverability and controllability in aircraft have been postulated as tactically advantageous, but little research has studied maneuvers or tactics that make use of these capabilities. In order to help fill this void, a real time tactical decision generation system for air combat engagements, Paladin, has been developed. Paladin models an air combat engagement as a series of discrete decisions. A detailed description of Paladin's decision making process is presented. This includes the sources of data used, methods of generating reasonable maneuvers for the Paladin aircraft, and selection criteria for choosing the "best" maneuver. Simulation results are presented that show Paladin to be relatively insensitive to errors introduced into the decision process by estimation of future positional and geometric data.

Trial maneuver generation and selection in the Paladin tactical decision generation system

NASA Technical Reports Server (NTRS)

Chappell, Alan R.; Mcmanus, John W.; Goodrich, Kenneth H.

1993-01-01

To date, increased levels of maneuverability and controllability in aircraft have been postulated as tactically advantageous, but little research has studied maneuvers or tactics that make use of these capabilities. In order to help fill this void, a real-time tactical decision generation system for air combat engagements, Paladin, has been developed. Paladin models an air combat engagement as a series of discrete decisions. A detailed description of Paladin's decision making process is presented. This includes the sources of data used, methods of generating reasonable maneuvers for the Paladin aircraft, and selection criteria for choosing the 'best' maneuver. Simulation results are presented that show Paladin to be relatively insensitive to errors introduced into the decision process by estimation of future positional and geometric data.

Doubly Fed Induction Generator Wind Turbines with Fuzzy Controller: A Survey

PubMed Central

Sathiyanarayanan, J. S.; Senthil Kumar, A.

2014-01-01

Wind energy is one of the extraordinary sources of renewable energy due to its clean character and free availability. With the increasing wind power penetration, the wind farms are directly influencing the power systems. The majority of wind farms are using variable speed wind turbines equipped with doubly fed induction generators (DFIG) due to their advantages over other wind turbine generators (WTGs). Therefore, the analysis of wind power dynamics with the DFIG wind turbines has become a very important research issue, especially during transient faults. This paper presents fuzzy logic control of doubly fed induction generator (DFIG) wind turbine in a sample power system. Fuzzy logic controller is applied to rotor side converter for active power control and voltage regulation of wind turbine. PMID:25028677

Vibration Test of a SNAP-8 Sodium-Potassium Alloy Pump

NASA Image and Video Library

1970-01-21

Aeronautics and Space Administration (NASA) Lewis Research Center. Aerojet General was contracted to design the SNAP-8 generator which employed a mercury Rankine system to convert the reactor’s heat into electrical power. The hermetically-sealed pump was designed to generate from 35 to 90 kilowatts of electrical power. In 1964 a SNAP-8 test rig with a mercury boiler and condenser was set up in cell W-1 of Lewis’ Engine Research Building to study the transients in the system’s three loops. In 1967 a complete Rankine system was operated for 60 days in W-1 to verify the integrity of the Lewis-developed mercury boiler. Further tests in 1969 verified the shutdown and startup of the system under normal and emergency conditions. Aerojet operated the first full-Rankine system in June 1966 and completed a 2500-hour endurance test in early 1969. Lewis and Aerojet’s success on the Rankine system was acknowledged with NASA Group Achievement Award in November 1970. The 1970 vibration tests, seen here, were conducted in Lewis’ Engine Research Building’s environmental laboratory. The testing replicated the shock and vibration expected to occur during the launch into space and subsequent maneuvering. The pump was analyzed on each of its major axes.

A Consistent System for Coding Laboratory Samples

NASA Astrophysics Data System (ADS)

Sih, John C.

1996-07-01

A formal laboratory coding system is presented to keep track of laboratory samples. Preliminary useful information regarding the sample (origin and history) is gained without consulting a research notebook. Since this system uses and retains the same research notebook page number for each new experiment (reaction), finding and distinguishing products (samples) of the same or different reactions becomes an easy task. Using this system multiple products generated from a single reaction can be identified and classified in a uniform fashion. Samples can be stored and filed according to stage and degree of purification, e.g. crude reaction mixtures, recrystallized samples, chromatographed or distilled products.

Man-vehicle systems research facility: Design and operating characteristics

NASA Technical Reports Server (NTRS)

1983-01-01

The Man-Vehicle Systems Research Facility (MVSRF) provides the capability of simulating aircraft (two with full crews), en route and terminal air traffic control and aircrew interactions, and advanced cockpit (1995) display representative of future generations of aircraft, all within the full mission context. The characteristics of this facility derive from research, addressing critical human factors issues that pertain to: (1) information requirements for the utilization and integration of advanced electronic display systems, (2) the interaction and distribution of responsibilities between aircrews and ground controllers, and (3) the automation of aircrew functions. This research has emphasized the need for high fidelity in simulations and for the capability to conduct full mission simulations of relevant aircraft operations. This report briefly describes the MVSRF design and operating characteristics.

Knowledge sharing and collaboration in translational research, and the DC-THERA Directory

PubMed Central

Gündel, Michaela; Austyn, Jonathan M.; Cavalieri, Duccio; Scognamiglio, Ciro; Brandizi, Marco

2011-01-01

Biomedical research relies increasingly on large collections of data sets and knowledge whose generation, representation and analysis often require large collaborative and interdisciplinary efforts. This dimension of ‘big data’ research calls for the development of computational tools to manage such a vast amount of data, as well as tools that can improve communication and access to information from collaborating researchers and from the wider community. Whenever research projects have a defined temporal scope, an additional issue of data management arises, namely how the knowledge generated within the project can be made available beyond its boundaries and life-time. DC-THERA is a European ‘Network of Excellence’ (NoE) that spawned a very large collaborative and interdisciplinary research community, focusing on the development of novel immunotherapies derived from fundamental research in dendritic cell immunobiology. In this article we introduce the DC-THERA Directory, which is an information system designed to support knowledge management for this research community and beyond. We present how the use of metadata and Semantic Web technologies can effectively help to organize the knowledge generated by modern collaborative research, how these technologies can enable effective data management solutions during and beyond the project lifecycle, and how resources such as the DC-THERA Directory fit into the larger context of e-science. PMID:21969471

Development of Residential SOFC Cogeneration System

NASA Astrophysics Data System (ADS)

Ono, Takashi; Miyachi, Itaru; Suzuki, Minoru; Higaki, Katsuki

2011-06-01

Since 2001 Kyocera has been developing 1kW class Solid Oxide Fuel Cell (SOFC) for power generation system. We have developed a cell, stack, module and system. Since 2004, Kyocera and Osaka Gas Co., Ltd. have been developed SOFC residential co-generation system. From 2007, we took part in the "Demonstrative Research on Solid Oxide Fuel Cells" Project conducted by New Energy Foundation (NEF). Total 57 units of 0.7kW class SOFC cogeneration systems had been installed at residential houses. In spite of residential small power demand, the actual electric efficiency was about 40%(netAC,LHV), and high CO2 reduction performance was achieved by these systems. Hereafter, new joint development, Osaka Gas, Toyota Motors, Kyocera and Aisin Seiki, aims early commercialization of residential SOFC CHP system.

Power Management and Distribution (PMAD) Model Development: Final Report

NASA Technical Reports Server (NTRS)

Metcalf, Kenneth J.

2011-01-01

Power management and distribution (PMAD) models were developed in the early 1990's to model candidate architectures for various Space Exploration Initiative (SEI) missions. They were used to generate "ballpark" component mass estimates to support conceptual PMAD system design studies. The initial set of models was provided to NASA Lewis Research Center (since renamed Glenn Research Center) in 1992. They were developed to estimate the characteristics of power conditioning components predicted to be available in the 2005 timeframe. Early 90's component and device designs and material technologies were projected forward to the 2005 timeframe, and algorithms reflecting those design and material improvements were incorporated into the models to generate mass, volume, and efficiency estimates for circa 2005 components. The models are about ten years old now and NASA GRC requested a review of them to determine if they should be updated to bring them into agreement with current performance projections or to incorporate unforeseen design or technology advances. This report documents the results of this review and the updated power conditioning models and new transmission line models generated to estimate post 2005 PMAD system masses and sizes. This effort continues the expansion and enhancement of a library of PMAD models developed to allow system designers to assess future power system architectures and distribution techniques quickly and consistently.

An efficient plant viral expression system generating orally immunogenic Norwalk virus-like particles.

PubMed

Santi, Luca; Batchelor, Lance; Huang, Zhong; Hjelm, Brooke; Kilbourne, Jacquelyn; Arntzen, Charles J; Chen, Qiang; Mason, Hugh S

2008-03-28

Virus-like particles (VLPs) derived from enteric pathogens like Norwalk virus (NV) are well suited to study oral immunization. We previously described stable transgenic plants that accumulate recombinant NV-like particles (rNVs) that were orally immunogenic in mice and humans. The transgenic approach suffers from long generation time and modest level of antigen accumulation. We now overcome these constraints with an efficient tobacco mosaic virus (TMV)-derived transient expression system using leaves of Nicotiana benthamiana. We produced properly assembled rNV at 0.8 mg/g leaf 12 days post-infection (dpi). Oral immunization of CD1 mice with 100 or 250 microg/dose of partially purified rNV elicited systemic and mucosal immune responses. We conclude that the plant viral transient expression system provides a robust research tool to generate abundant quantities of rNV as enriched, concentrated VLP preparations that are orally immunogenic.

An efficient plant viral expression system generating orally immunogenic Norwalk virus-like particles

PubMed Central

Santi, Luca; Batchelor, Lance; Huang, Zhong; Hjelm, Brooke; Kilbourne, Jacquelyn; Arntzen, Charles J.; Chen, Qiang; Mason, Hugh S.

2009-01-01

Virus like particles (VLPs) derived from enteric pathogens like Norwalk virus (NV) are well suited to study oral immunization. We previously described stable transgenic plants that accumulate recombinant NV-like particles (rNV) that were orally immunogenic in mice and humans. The transgenic approach suffers from long generation time and modest level of antigen accumulation. We now overcome these constraints with an efficient tobacco mosaic virus (TMV)-derived transient expression system using leaves of Nicotiana benthamiana. We produced properly assembled rNV at 0.8 mg/g leaf 12 days post infection. Oral immunization of CD1 mice with 100 or 250 μg/dose of partially purified rNV elicited systemic and mucosal immune responses. We conclude that the plant viral transient expression system provides a robust research tool to generate abundant quantities of rNV as enriched, concentrated VLP preparations that are orally immunogenic. PMID:18325641

Halbach array motor/generators: A novel generalized electric machine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merritt, B.T.; Post, R.F.; Dreifuerst, G.R.

1995-02-01

For many years Klaus Halbach has been investigating novel designs for permanent magnet arrays, using advanced analytical approaches and employing a keen insight into such systems. One of his motivations for this research was to find more efficient means for the utilization of permanent magnets for use in particle accelerators and in the control of particle beams. As a result of his pioneering work, high power free-electron laser systems, such as the ones built at the Lawrence Livermore Laboratory, became feasible, and his arrays have been incorporated into other particle-focusing systems of various types. This paper reports another, quite different,more » application of Klaus` work, in the design of high power, high efficiency, electric generators and motors. When tested, these motor/generator systems display some rather remarkable properties. Their success derives from the special properties which these arrays, which the authors choose to call {open_quotes}Halbach arrays,{close_quotes} possess.« less

Color Helmet-Mounted Display System for In-Flight Simulation on the RASCAL Research Helicopter

NASA Technical Reports Server (NTRS)

Edwards, Tim; Barnhart, Warren; Sawyer, Kevin; Aiken, Edwin W. (Technical Monitor)

1995-01-01

A high performance color helmet mounted display (HMD) system for in-flight simulation and research has been developed for the Rotorcraft Aircrew Systems Concepts Laboratory (RASCAL). The display system consists of a programmable display generator, a display electronics unit, a head tracker, and the helmet with display optics. The system provides a maximum of 1024 x 1280 resolution, a 4:1 contrast ratio, and a brightness of 1100fL utilizing currently available technologies. This paper describes the major features and components of the system. Also discussed are the measured performance of the system and the design techniques that allowed the development of a full color HMD.

Distributed Practicum Supervision in a Managed Learning Environment (MLE)

ERIC Educational Resources Information Center

Carter, David

2005-01-01

This evaluation-research feasibility study piloted the creation of a technology-mediated managed learning environment (MLE) involving the implementation of one of a new generation of instructionally driven management information systems (IMISs). The system, and supporting information and communications technology (ICT) was employed to support…

Hardware-in-the-loop projector system for light detection and ranging sensor testing

NASA Astrophysics Data System (ADS)

Kim, Hajin J.; Naumann, Charles B.; Cornell, Michael C.

2012-08-01

Efforts in developing a synthetic environment for testing light detection and ranging (LADAR) sensors in a hardware-in-the-loop simulation are continuing at the Aviation and Missile Research, Engineering, and Development Center of the U.S. Army Research, Engineering and Development Command (RDECOM). Current activities have concentrated on evaluating the optical projection techniques for the LADAR synthetic environment. Schemes for generating the optical signals representing the individual pixels of the projection are of particular interest. Several approaches have been investigated and tested with emphasis on operating wavelength, intensity dynamic range and uniformity, and flexibility in pixel waveform generation. This paper will discuss some of the results from these current efforts at RDECOM's System Simulation and Development Directorate's Electro Optical Technology Development Laboratory.

Vectors into the Future of Mass and Interpersonal Communication Research: Big Data, Social Media, and Computational Social Science.

PubMed

Cappella, Joseph N

2017-10-01

Simultaneous developments in big data, social media, and computational social science have set the stage for how we think about and understand interpersonal and mass communication. This article explores some of the ways that these developments generate 4 hypothetical "vectors" - directions - into the next generation of communication research. These vectors include developments in network analysis, modeling interpersonal and social influence, recommendation systems, and the blurring of distinctions between interpersonal and mass audiences through narrowcasting and broadcasting. The methods and research in these arenas are occurring in areas outside the typical boundaries of the communication discipline but engage classic, substantive questions in mass and interpersonal communication.

Recycling Flight Hardware Components and Systems to Reduce Next Generation Research Costs

NASA Technical Reports Server (NTRS)

Turner, Wlat

2011-01-01

With the recent 'new direction' put forth by President Obama identifying NASA's new focus in research rather than continuing on a path to return to the Moon and Mars, the focus of work at Kennedy Space Center (KSC) may be changing dramatically. Research opportunities within the micro-gravity community potentially stands at the threshold of resurgence when the new direction of the agency takes hold for the next generation of experimenters. This presentation defines a strategy for recycling flight experiment components or part numbers, in order to reduce research project costs, not just in component selection and fabrication, but in expediting qualification of hardware for flight. A key component of the strategy is effective communication of relevant flight hardware information and available flight hardware components to researchers, with the goal of 'short circuiting' the design process for flight experiments

Studies of Disks Around the Sun and Other Stars

NASA Technical Reports Server (NTRS)

Stern, S. Alan

1997-01-01

This is a NASA Origins of Solar Systems research program, and this NASA Headquarters grant has now been transferred to a new grant at NASA GSFC (NAG5-4082). Thus the need for this 'Final Report' on a project that is not, in fact, complete. We are conducting research designed to enhance our understanding of the evolution and detectability of comet clouds and disks. This area holds promise for also improving our understanding of outer solar system formation, the bombardment history of the planets, the transport of volatiles and organics from the outer solar system to the inner planets, and to the ultimate fate of comet clouds around the Sun and other stars. According to "standard" theory, both the Kuiper Belt and the Oort Cloud are (at least in part) natural products of the planetary accumulation stage of solar system formation. One expects such assemblages to be a common attribute of other solar systems. Our program consists of modeling collisions in the Kuiper Belt and the dust disks around other stars. The modeling effort focuses on moving from our simple, first-generation, Kuiper Belt collision rate model, to a time-dependent, second-generation model that incorporates physical collisions, velocity evolution, dynamical erosion, and various dust transport mechanisms. This second generation model is to be used to study the evolution of surface mass density and the object-size spectrum in the disk.

Parametric Study of Radiator Concepts for a Stirling Radioisotope Power System Applicable to Deep Space Mission

NASA Technical Reports Server (NTRS)

Juhasz, Albert J.; Tew, Roy C.; Thieme, Lanny G.

2000-01-01

The Department of Energy (DOE) and the NASA Glenn Research Center are developing a Stirling converter for an advanced radioisotope power system to provide spacecraft onboard electric power for NASA deep space missions. This high-efficiency converter is being evaluated as an alternative to replace the much lower efficiency radioisotope thermoelectric generator (RTG). The current power requirement (six years after beginning of mission (BOM) for a mission to Jupiter) is 210 W(sub e) (watts electric) to be generated by two separate power systems, one on each side of the spacecraft. Both two-converter and four-converter system designs are being considered, depending on the amount of required redundancy.

The Mod-2 wind turbine development project

NASA Technical Reports Server (NTRS)

Linscott, B. S.; Dennett, J. T.; Gordon, L. H.

1981-01-01

A major phase of the Federal Wind Energy Program, the Mod-2 wind turbine, a second-generation machine developed by the Boeing Engineering and Construction Co. for the U.S. Department of Energy and the Lewis Research Center of the National Aeronautics and Space Administration, is described. The Mod-2 is a large (2.5-MW power rating) horizontal-axis wind turbine designed for the generation of electrical power on utility networks. Three machines were built and are located in a cluster at Goodnoe Hills, Washington. All technical aspects of the project are described: design approach, significant innovation features, the mechanical system, the electrical power system, the control system, and the safety system.

Optimizing the U.S. Electric System with a High Penetration of Renewables

NASA Astrophysics Data System (ADS)

Corcoran, B. A.; Jacobson, M. Z.

2013-12-01

As renewable energy generators are increasingly being installed throughout the U.S., there is growing interest in interconnecting diverse renewable generators (primarily wind and solar) across large geographic areas through an enhanced transmission system. This reduces variability in the aggregate power output, increases system reliability, and allows for the development of the best overall group of renewable technologies and sites to meet the load. Studies are therefore needed to determine the most efficient and economical plan to achieve large area interconnections in a future electric system with a high penetration of renewables. This research quantifies the effects of aggregating electric load together with diverse renewable generation throughout the ten Federal Energy Regulatory Commission (FERC) regions in the contiguous U.S. A deterministic linear program has been built in AMPL (A Mathematical Programming Language) to solve for the least-cost organizational structure and system (generators, transmission, and storage) for a highly renewable electric grid. The analysis will 1) examine a highly renewable 2006 electric system, including various sensitivity cases and additional system components such as additional load from electric vehicles, and 2) create a 'roadmap' from the existing 2006 system to a highly renewable system in 2030, accounting for projected price and demand changes and generator retirements based on age and environmental regulations. Ideally, results from this study will offer insight for a federal renewable energy policy (such as a renewable portfolio standard) and how to best organize U.S. regions for transmission planning.

MOD-OA 200 kW wind turbine generator engineeringing

NASA Technical Reports Server (NTRS)

Andersen, T. S.; Bodenschatz, C. A.; Eggers, A. G.; Hughes, P. S.; Lampe, R. F.

1980-01-01

Engineering drawings and the detailed mechanical and electrical design of a horizontal-axis wind turbine designed for DOE at the NASA Lewis Research Center and installed in Clayton, New Mexico are discussed. The drawings show the hub, pitch change mechanism, drive train, nacelle equipment, yaw drive system, tower, foundation, electrical power systems, and the control and safety systems.

Computational and Experimental Evaluation of a Complex Inlet Swirl Pattern Generation System (POSTPRINT)

DTIC Science & Technology

2016-08-01

Sanders, Chase A. Nessler, William W. Copenhaver, Michael G. List, and Timothy J. Janczewski Turbomachinery Branch Turbine Engine Division AUGUST...Branch Turbine Engine Division Turbine Engine Division Aerospace Systems Directorate //Signature// ROBERT D. HANCOCK Principal Scientist Turbine ...ORGANIZATION Turbomachinery Branch Turbine Engine Division Air Force Research Laboratory, Aerospace Systems Directorate Wright-Patterson Air Force

Microcomputer-Based Detachment Administrative Management System for the LAMPS (Light Airborne Multi-Purpose System) Community. A Requirements Analysis.

DTIC Science & Technology

1985-09-01

management and recurring reports generation . Included are the results of user interviews which were conducted to determine oossible system functions...9 A. GENERAL ...................... .......... 3 B. RESEARCH OBJECTIVES ............................ I0 C. SCOPE .. D... GENERAL DESCRIPTION (LAMPS) ...................... 9. LPMrOS CRGANIZAT r.N ............................... C. REPCRT>1NG RECLUIRE,’ENTS

Only Self-Generated Actions Create Sensori-Motor Systems in the Developing Brain

ERIC Educational Resources Information Center

James, Karin Harman; Swain, Shelley N.

2011-01-01

Previous research shows that sensory and motor systems interact during perception, but how these connections among systems are created during development is unknown. The current work exposes young children to novel "verbs" and objects through either (a) actively exploring the objects or (b) by seeing an experimenter interact with the objects.…

Investigation of Insulation Materials for Future Radioisotope Power Systems (RPS)

NASA Technical Reports Server (NTRS)

Cornell, Peggy A.; Hurwitz, Frances I.; Ellis, David L.; Schmitz, Paul C.

2013-01-01

NASA's Radioisotope Power System (RPS) Technology Advancement Project is developing next generation high temperature insulation materials that directly benefit thermal management and improve performance of RPS for future science missions. Preliminary studies on the use of multilayer insulation (MLI) for Stirling convertors used on the Advanced Stirling Radioisotope Generator (ASRG) have shown the potential benefits of MLI for space vacuum applications in reducing generator size and increasing specific power (W/kg) as compared to the baseline Microtherm HT (Microtherm, Inc.) insulation. Further studies are currently being conducted at NASA Glenn Research Center (GRC) on candidate MLI foils and aerogel composite spacers. This paper presents the method of testing of foils and spacers and experimental results to date.

Investigation of Insulation Materials for Future Radioisotope Power Systems

NASA Technical Reports Server (NTRS)

Cornell, Peggy A.; Hurwitz, Frances I.; Ellis, David L.; Schmitz, Paul C.

2013-01-01

NASA's Radioisotope Power Systems (RPS) Technology Advancement Project is developing next generation high-temperature insulation materials that directly benefit thermal management and improve performance of RPS for future science missions. Preliminary studies on the use of multilayer insulation (MLI) for Stirling convertors used on the Advanced Stirling Radioisotope Generator (ASRG) have shown the potential benefits of MLI for space vacuum applications in reducing generator size and increasing specific power (W/kg) as compared to the baseline Microtherm HT (Microtherm, Inc.) insulation. Further studies are currently being conducted at NASA Glenn Research Center on candidate MLI foils and aerogel composite spacers. This paper presents the method of testing of foils and spacers and experimental results to date.

Point-to-Point! Validation of the Small Aircraft Transportation System Higher Volume Operations Concept

NASA Technical Reports Server (NTRS)

Williams, Daniel M.

2006-01-01

Described is the research process that NASA researchers used to validate the Small Aircraft Transportation System (SATS) Higher Volume Operations (HVO) concept. The four phase building-block validation and verification process included multiple elements ranging from formal analysis of HVO procedures to flight test, to full-system architecture prototype that was successfully shown to the public at the June 2005 SATS Technical Demonstration in Danville, VA. Presented are significant results of each of the four research phases that extend early results presented at ICAS 2004. HVO study results have been incorporated into the development of the Next Generation Air Transportation System (NGATS) vision and offer a validated concept to provide a significant portion of the 3X capacity improvement sought after in the United States National Airspace System (NAS).

Whither systems medicine?

PubMed Central

Apweiler, Rolf; Beissbarth, Tim; Berthold, Michael R; Blüthgen, Nils; Burmeister, Yvonne; Dammann, Olaf; Deutsch, Andreas; Feuerhake, Friedrich; Franke, Andre; Hasenauer, Jan; Hoffmann, Steve; Höfer, Thomas; Jansen, Peter LM; Kaderali, Lars; Klingmüller, Ursula; Koch, Ina; Kohlbacher, Oliver; Kuepfer, Lars; Lammert, Frank; Maier, Dieter; Pfeifer, Nico; Radde, Nicole; Rehm, Markus; Roeder, Ingo; Saez-Rodriguez, Julio; Sax, Ulrich; Schmeck, Bernd; Schuppert, Andreas; Seilheimer, Bernd; Theis, Fabian J; Vera, Julio; Wolkenhauer, Olaf

2018-01-01

New technologies to generate, store and retrieve medical and research data are inducing a rapid change in clinical and translational research and health care. Systems medicine is the interdisciplinary approach wherein physicians and clinical investigators team up with experts from biology, biostatistics, informatics, mathematics and computational modeling to develop methods to use new and stored data to the benefit of the patient. We here provide a critical assessment of the opportunities and challenges arising out of systems approaches in medicine and from this provide a definition of what systems medicine entails. Based on our analysis of current developments in medicine and healthcare and associated research needs, we emphasize the role of systems medicine as a multilevel and multidisciplinary methodological framework for informed data acquisition and interdisciplinary data analysis to extract previously inaccessible knowledge for the benefit of patients. PMID:29497170

Collecting, Integrating, and Disseminating Patient-Reported Outcomes for Research in a Learning Healthcare System

PubMed Central

Harle, Christopher A.; Lipori, Gloria; Hurley, Robert W.

2016-01-01

Introduction: Advances in health policy, research, and information technology have converged to increase the electronic collection and use of patient-reported outcomes (PROs). Therefore, it is important to share lessons learned in implementing PROs in research information systems. Case Description: The purpose of this case study is to describe a novel information system for electronic PROs and lessons learned in implementing that system to support research in an academic health center. The system incorporates freely available and commercial software and involves clinical and research workflows that support the collection, transformation, and research use of PRO data. The software and processes that comprise the system serve three main functions, (i) collecting electronic PROs in clinical care, (ii) integrating PRO data with non-patient generated clinical data, and (iii) disseminating data to researchers through the institution’s research informatics infrastructure, including the i2b2 (Informatics for Integrating Biology and the Bedside) system. Strategies: Our successful design and implementation was driven by three overarching strategies. First, we selected and implemented multiple interfaced technologies to support PRO collection, management, and research use. Second, we aimed to use standardized approaches to measuring PROs, sending PROs between systems, and disseminating PROs. Finally, we focused on using technologies and processes that aligned with existing clinical research information management strategies within our organization. Conclusion: These experiences and lessons may help future implementers and researchers enhance the scale and sustainable use of systems for research use of PROs. PMID:27563683

Collecting, Integrating, and Disseminating Patient-Reported Outcomes for Research in a Learning Healthcare System.

PubMed

Harle, Christopher A; Lipori, Gloria; Hurley, Robert W

2016-01-01

Advances in health policy, research, and information technology have converged to increase the electronic collection and use of patient-reported outcomes (PROs). Therefore, it is important to share lessons learned in implementing PROs in research information systems. The purpose of this case study is to describe a novel information system for electronic PROs and lessons learned in implementing that system to support research in an academic health center. The system incorporates freely available and commercial software and involves clinical and research workflows that support the collection, transformation, and research use of PRO data. The software and processes that comprise the system serve three main functions, (i) collecting electronic PROs in clinical care, (ii) integrating PRO data with non-patient generated clinical data, and (iii) disseminating data to researchers through the institution's research informatics infrastructure, including the i2b2 (Informatics for Integrating Biology and the Bedside) system. Our successful design and implementation was driven by three overarching strategies. First, we selected and implemented multiple interfaced technologies to support PRO collection, management, and research use. Second, we aimed to use standardized approaches to measuring PROs, sending PROs between systems, and disseminating PROs. Finally, we focused on using technologies and processes that aligned with existing clinical research information management strategies within our organization. These experiences and lessons may help future implementers and researchers enhance the scale and sustainable use of systems for research use of PROs.

Mimicking Natural Photosynthesis: Solar to Renewable H2 Fuel Synthesis by Z-Scheme Water Splitting Systems

PubMed Central

2018-01-01

Visible light-driven water splitting using cheap and robust photocatalysts is one of the most exciting ways to produce clean and renewable energy for future generations. Cutting edge research within the field focuses on so-called “Z-scheme” systems, which are inspired by the photosystem II–photosystem I (PSII/PSI) coupling from natural photosynthesis. A Z-scheme system comprises two photocatalysts and generates two sets of charge carriers, splitting water into its constituent parts, hydrogen and oxygen, at separate locations. This is not only more efficient than using a single photocatalyst, but practically it could also be safer. Researchers within the field are constantly aiming to bring systems toward industrial level efficiencies by maximizing light absorption of the materials, engineering more stable redox couples, and also searching for new hydrogen and oxygen evolution cocatalysts. This review provides an in-depth survey of relevant Z-schemes from past to present, with particular focus on mechanistic breakthroughs, and highlights current state of the art systems which are at the forefront of the field. PMID:29676566

Sustainable urban systems: Co-design and framing for transformation.

PubMed

Webb, Robert; Bai, Xuemei; Smith, Mark Stafford; Costanza, Robert; Griggs, David; Moglia, Magnus; Neuman, Michael; Newman, Peter; Newton, Peter; Norman, Barbara; Ryan, Chris; Schandl, Heinz; Steffen, Will; Tapper, Nigel; Thomson, Giles

2018-02-01

Rapid urbanisation generates risks and opportunities for sustainable development. Urban policy and decision makers are challenged by the complexity of cities as social-ecological-technical systems. Consequently there is an increasing need for collaborative knowledge development that supports a whole-of-system view, and transformational change at multiple scales. Such holistic urban approaches are rare in practice. A co-design process involving researchers, practitioners and other stakeholders, has progressed such an approach in the Australian context, aiming to also contribute to international knowledge development and sharing. This process has generated three outputs: (1) a shared framework to support more systematic knowledge development and use, (2) identification of barriers that create a gap between stated urban goals and actual practice, and (3) identification of strategic focal areas to address this gap. Developing integrated strategies at broader urban scales is seen as the most pressing need. The knowledge framework adopts a systems perspective that incorporates the many urban trade-offs and synergies revealed by a systems view. Broader implications are drawn for policy and decision makers, for researchers and for a shared forward agenda.

Mimicking Natural Photosynthesis: Solar to Renewable H2 Fuel Synthesis by Z-Scheme Water Splitting Systems.

PubMed

Wang, Yiou; Suzuki, Hajime; Xie, Jijia; Tomita, Osamu; Martin, David James; Higashi, Masanobu; Kong, Dan; Abe, Ryu; Tang, Junwang

2018-05-23

Visible light-driven water splitting using cheap and robust photocatalysts is one of the most exciting ways to produce clean and renewable energy for future generations. Cutting edge research within the field focuses on so-called "Z-scheme" systems, which are inspired by the photosystem II-photosystem I (PSII/PSI) coupling from natural photosynthesis. A Z-scheme system comprises two photocatalysts and generates two sets of charge carriers, splitting water into its constituent parts, hydrogen and oxygen, at separate locations. This is not only more efficient than using a single photocatalyst, but practically it could also be safer. Researchers within the field are constantly aiming to bring systems toward industrial level efficiencies by maximizing light absorption of the materials, engineering more stable redox couples, and also searching for new hydrogen and oxygen evolution cocatalysts. This review provides an in-depth survey of relevant Z-schemes from past to present, with particular focus on mechanistic breakthroughs, and highlights current state of the art systems which are at the forefront of the field.

Solar photovoltaics: Stand alone applications. [NASA Lewis Research Center research and development

NASA Technical Reports Server (NTRS)

Deyo, J. N.

1980-01-01

The Lewis Research Center involvement in space photovoltaic research and development and in using photovoltaics for terrestrial applications is described with emphasis on applications in which the normal source of power may be a diesel generator, batteries, or other types of power not connected to a utility grid. Once an application is processed, technology is developed and demonstrated with a user who participates in the cost and furnishes the site. Projects completed related to instruments, communication, refrigeration, and highways, are described as well as warning systems, weather stations, fire lookouts, and village power systems. A commercially available photovoltaic powered electric fence charger is the result of Lewis research and development.

Application of Particle Swarm Optimization in Computer Aided Setup Planning

NASA Astrophysics Data System (ADS)

Kafashi, Sajad; Shakeri, Mohsen; Abedini, Vahid

2011-01-01

New researches are trying to integrate computer aided design (CAD) and computer aided manufacturing (CAM) environments. The role of process planning is to convert the design specification into manufacturing instructions. Setup planning has a basic role in computer aided process planning (CAPP) and significantly affects the overall cost and quality of machined part. This research focuses on the development for automatic generation of setups and finding the best setup plan in feasible condition. In order to computerize the setup planning process, three major steps are performed in the proposed system: a) Extraction of machining data of the part. b) Analyzing and generation of all possible setups c) Optimization to reach the best setup plan based on cost functions. Considering workshop resources such as machine tool, cutter and fixture, all feasible setups could be generated. Then the problem is adopted with technological constraints such as TAD (tool approach direction), tolerance relationship and feature precedence relationship to have a completely real and practical approach. The optimal setup plan is the result of applying the PSO (particle swarm optimization) algorithm into the system using cost functions. A real sample part is illustrated to demonstrate the performance and productivity of the system.

Challenges and opportunities associated with waste management in India

PubMed Central

Kumar, Sunil; Smith, Stephen R.; Fowler, Geoff; Velis, Costas; Kumar, S. Jyoti; Arya, Shashi; Rena; Kumar, Rakesh

2017-01-01

India faces major environmental challenges associated with waste generation and inadequate waste collection, transport, treatment and disposal. Current systems in India cannot cope with the volumes of waste generated by an increasing urban population, and this impacts on the environment and public health. The challenges and barriers are significant, but so are the opportunities. This paper reports on an international seminar on ‘Sustainable solid waste management for cities: opportunities in South Asian Association for Regional Cooperation (SAARC) countries’ organized by the Council of Scientific and Industrial Research-National Environmental Engineering Research Institute and the Royal Society. A priority is to move from reliance on waste dumps that offer no environmental protection, to waste management systems that retain useful resources within the economy. Waste segregation at source and use of specialized waste processing facilities to separate recyclable materials has a key role. Disposal of residual waste after extraction of material resources needs engineered landfill sites and/or investment in waste-to-energy facilities. The potential for energy generation from landfill via methane extraction or thermal treatment is a major opportunity, but a key barrier is the shortage of qualified engineers and environmental professionals with the experience to deliver improved waste management systems in India. PMID:28405362

Assessment of computational issues associated with analysis of high-lift systems

NASA Technical Reports Server (NTRS)

Balasubramanian, R.; Jones, Kenneth M.; Waggoner, Edgar G.

1992-01-01

Thin-layer Navier-Stokes calculations for wing-fuselage configurations from subsonic to hypersonic flow regimes are now possible. However, efficient, accurate solutions for using these codes for two- and three-dimensional high-lift systems have yet to be realized. A brief overview of salient experimental and computational research is presented. An assessment of the state-of-the-art relative to high-lift system analysis and identification of issues related to grid generation and flow physics which are crucial for computational success in this area are also provided. Research in support of the high-lift elements of NASA's High Speed Research and Advanced Subsonic Transport Programs which addresses some of the computational issues is presented. Finally, fruitful areas of concentrated research are identified to accelerate overall progress for high lift system analysis and design.

Application of carbon nanotubes in perovskite solar cells: A review

NASA Astrophysics Data System (ADS)

Oo, Thet Tin; Debnath, Sujan

2017-11-01

Solar power, as alternative renewable energy source, has gained momentum in global energy generation in recent time. Solar photovoltaics (PV) systems now fulfill a significant portion of electricity demand and the capacity of solar PV capacity is growing every year. PV cells efficiency has improved significantly following decades of research, evolving into third generations of PV cells. These third generation PV cells are set out to provide low-cost and efficient PV systems, further improving the commercial competitiveness of solar energy generation. Among these latest generations of PV cells, perovskite solar cells have gained attraction due to the simple manufacturing process and the immense growth in PV efficiency in a short period of research and development. Despite these advantages, perovskite solar cells are known for the weak stability and decomposition in exposure to humidity and high temperature, hindering the possibility of commercialization. This paper will discuss the role of carbon nanotubes (CNTs) in improving the efficiency and stability of perovskite solar cells, in various components such as perovskite layer and hole transport layer, as well as the application of CNTs in unique aspects. These includes the use of CNTs fiber in making the perovskite solar cells flexible, as well as simplification of perovskite PV production by using CNT flash evaporation printing process. Despite these advances, challenges remain in incorporation CNTs into perovskite such as lower conversion efficiency compared to rare earth metals and improvements need to be made. Thus, the paper will be also highlighting the CNTs materials suggested for further research and improvement of perovskite solar cells.

Limits and Economic Effects of Distributed PV Generation in North and South Carolina

NASA Astrophysics Data System (ADS)

Holt, Kyra Moore

The variability of renewable sources, such as wind and solar, when integrated into the electrical system must be compensated by traditional generation sources in-order to maintain the constant balance of supply and demand required for grid stability. The goal of this study is to analyze the effects of increasing large levels of solar Photovoltaic (PV) penetration (in terms of a percentage of annual energy production) on a test grid with similar characteristics to the Duke Energy Carolinas (DEC) and Progress Energy Carolinas (PEC) regions of North and South Carolina. PV production is modeled entering the system at the distribution level and regional PV capacity is based on household density. A gridded hourly global horizontal irradiance (GHI) dataset is used to capture the variable nature of PV generation. A unit commitment model (UCM) is then used determine the hourly dispatch of generators based on generator parameters and costs to supply generation to meet demand. Annual modeled results for six different scenarios are evaluated to determine technical, environmental and economic effects of varying levels of distributed PV penetration on the system. This study finds that the main limiting factor for PV integration in the DEC and PEC balancing authority regions is defined by the large generating capacity of base-load nuclear plants within the system. This threshold starts to affect system stability at integration levels of 5.7%. System errors, defined by imbalances caused by over or under generation with respect to demand, are identified in the model however the validity of these errors in real world context needs further examination due to the lack of high frequency irradiance data and modeling limitations. Operational system costs decreased as expected with PV integration although further research is needed to explore the impacts of the capital costs required to achieve the penetration levels found in this study. PV system generation was found to mainly displace coal generation creating a loss of revenue for generator owners. In all scenarios, CO 2 emissions were reduced with PV integration. This reduction could be used to meet impending EPA state-specific CO2 emissions targets.

Negative health system effects of Global Fund's investments in AIDS, tuberculosis and malaria from 2002 to 2009: systematic review.

PubMed

Car, Josip; Paljärvi, Tapio; Car, Mate; Kazeem, Ayodele; Majeed, Azeem; Atun, Rifat

2012-10-01

By using the Global Fund as a case example, we aim to critically evaluate the evidence generated from 2002 to 2009 for potential negative health system effects of Global Health Initiatives (GHI). Systematic review of research literature. Developing Countries. All interventions potentially affecting health systems that were funded by the Global Fund. Negative health system effects of Global Fund investments as reported by study authors. We identified 24 studies commenting on adverse effects on health systems arising from Global Fund investments. Sixteen were quantitative studies, six were qualitative and two used both quantitative and qualitative methods, but none explicitly stated that the studies were originally designed to capture or to assess health system effects (positive or negative). Only seemingly anecdotal evidence or authors' perceptions/interpretations of circumstances could be extracted from the included studies. This study shows that much of the currently available evidence generated between 2002 and 2009 on GHIs potential negative health system effects is not of the quality expected or needed to best serve the academic or broader community. The majority of the reviewed research did not fulfil the requirements of rigorous scientific evidence.

The development of the Nucleus Freedom Cochlear implant system.

PubMed

Patrick, James F; Busby, Peter A; Gibson, Peter J

2006-12-01

Cochlear Limited (Cochlear) released the fourth-generation cochlear implant system, Nucleus Freedom, in 2005. Freedom is based on 25 years of experience in cochlear implant research and development and incorporates advances in medicine, implantable materials, electronic technology, and sound coding. This article presents the development of Cochlear's implant systems, with an overview of the first 3 generations, and details of the Freedom system: the CI24RE receiver-stimulator, the Contour Advance electrode, the modular Freedom processor, the available speech coding strategies, the input processing options of Smart Sound to improve the signal before coding as electrical signals, and the programming software. Preliminary results from multicenter studies with the Freedom system are reported, demonstrating better levels of performance compared with the previous systems. The final section presents the most recent implant reliability data, with the early findings at 18 months showing improved reliability of the Freedom implant compared with the earlier Nucleus 3 System. Also reported are some of the findings of Cochlear's collaborative research programs to improve recipient outcomes. Included are studies showing the benefits from bilateral implants, electroacoustic stimulation using an ipsilateral and/or contralateral hearing aid, advanced speech coding, and streamlined speech processor programming.

Integration of Research for an Exhaust Thermoelectric Generator and the Outer Flow Field of a Car

NASA Astrophysics Data System (ADS)

Jiang, T.; Su, C. Q.; Deng, Y. D.; Wang, Y. P.

2017-05-01

The exhaust thermoelectric generator (TEG) can generate electric power from a car engine's waste heat. It is important to maintain a sufficient temperature difference across the thermoelectric modules. The radiator is connected to the cooling units of the thermoelectric modules and used to take away the heat from the TEG system. This paper focuses on the research for the integration of a TEG radiator and the flow field of the car chassis, aiming to cool the radiator by the high speed flow around the chassis. What is more, the TEG radiator is designed as a spoiler to optimize the flow field around the car chassis and even reduce the aerodynamic drag. Concentrating on the flow pressure of the radiator and the aerodynamic drag force, a sedan model with eight different schemes of radiator configurations are studied by computational fluid dynamics simulation. Finally, the simulation results indicate that a reasonable radiator configuration can not only generate high flow pressure to improve the cooling performance, which provides a better support for the TEG system, but also acts as a spoiler to reduce the aerodynamic drag force.

Quantifying construction and demolition waste: an analytical review.

PubMed

Wu, Zezhou; Yu, Ann T W; Shen, Liyin; Liu, Guiwen

2014-09-01

Quantifying construction and demolition (C&D) waste generation is regarded as a prerequisite for the implementation of successful waste management. In literature, various methods have been employed to quantify the C&D waste generation at both regional and project levels. However, an integrated review that systemically describes and analyses all the existing methods has yet to be conducted. To bridge this research gap, an analytical review is conducted. Fifty-seven papers are retrieved based on a set of rigorous procedures. The characteristics of the selected papers are classified according to the following criteria - waste generation activity, estimation level and quantification methodology. Six categories of existing C&D waste quantification methodologies are identified, including site visit method, waste generation rate method, lifetime analysis method, classification system accumulation method, variables modelling method and other particular methods. A critical comparison of the identified methods is given according to their characteristics and implementation constraints. Moreover, a decision tree is proposed for aiding the selection of the most appropriate quantification method in different scenarios. Based on the analytical review, limitations of previous studies and recommendations of potential future research directions are further suggested. Copyright © 2014 Elsevier Ltd. All rights reserved.

Interactive web-based mapping: bridging technology and data for health

PubMed Central

2011-01-01

Background The Community Health Information System (CHIS) online mapping system was first launched in 1998. Its overarching goal was to provide researchers, residents and organizations access to health related data reflecting the overall health and well-being of their communities within the Greater Houston area. In September 2009, initial planning and development began for the next generation of CHIS. The overarching goal for the new version remained to make health data easily accessible for a wide variety of research audiences. However, in the new version we specifically sought to make the CHIS truly interactive and give the user more control over data selection and reporting. Results In July 2011, a beta version of the next-generation of the application was launched. This next-generation is also a web based interactive mapping tool comprised of two distinct portals: the Breast Health Portal and Project Safety Net. Both are accessed via a Google mapping interface. Geographic coverage for the portals is currently an 8 county region centered on Harris County, Texas. Data accessed by the application include Census 2000, Census 2010 (underway), cancer incidence from the Texas Cancer Registry (TX Dept. of State Health Services), death data from Texas Vital Statistics, clinic locations for free and low-cost health services, along with service lists, hours of operation, payment options and languages spoken, uninsured and poverty data. Conclusions The system features query on the fly technology, which means the data is not generated until the query is provided to the system. This allows users to interact in real-time with the databases and generate customized reports and maps. To the author's knowledge, the Breast Health Portal and Project Safety Net are the first local-scale interactive online mapping interfaces for public health data which allow users to control the data generated. For example, users may generate breast cancer incidence rates by Census tract, in real time, for women aged 40-64. Conversely, they could then generate the same rates for women aged 35-55. The queries are user controlled. PMID:22195603

A Simple, Low-cost, and Robust System to Measure the Volume of Hydrogen Evolved by Chemical Reactions with Aqueous Solutions

PubMed Central

Brack, Paul; Dann, Sandie; Wijayantha, K. G. Upul; Adcock, Paul; Foster, Simon

2016-01-01

There is a growing research interest in the development of portable systems which can deliver hydrogen on-demand to proton exchange membrane (PEM) hydrogen fuel cells. Researchers seeking to develop such systems require a method of measuring the generated hydrogen. Herein, we describe a simple, low-cost, and robust method to measure the hydrogen generated from the reaction of solids with aqueous solutions. The reactions are conducted in a conventional one-necked round-bottomed flask placed in a temperature controlled water bath. The hydrogen generated from the reaction in the flask is channeled through tubing into a water-filled inverted measuring cylinder. The water displaced from the measuring cylinder by the incoming gas is diverted into a beaker on a balance. The balance is connected to a computer, and the change in the mass reading of the balance over time is recorded using data collection and spreadsheet software programs. The data can then be approximately corrected for water vapor using the method described herein, and parameters such as the total hydrogen yield, the hydrogen generation rate, and the induction period can also be deduced. The size of the measuring cylinder and the resolution of the balance can be changed to adapt the setup to different hydrogen volumes and flow rates. PMID:27584581

Three-Dimensional Displays In The Future Flight Station

NASA Astrophysics Data System (ADS)

Bridges, Alan L.

1984-10-01

This review paper summarizes the development and applications of computer techniques for the representation of three-dimensional data in the future flight station. It covers the development of the Lockheed-NASA Advanced Concepts Flight Station (ACFS) research simulators. These simulators contain: A Pilot's Desk Flight Station (PDFS) with five 13- inch diagonal, color, cathode ray tubes on the main instrument panel; a computer-generated day and night visual system; a six-degree-of-freedom motion base; and a computer complex. This paper reviews current research, development, and evaluation of easily modifiable display systems and software requirements for three-dimensional displays that may be developed for the PDFS. This includes the analysis and development of a 3-D representation of the entire flight profile. This 3-D flight path, or "Highway-in-the-Sky", will utilize motion and perspective cues to tightly couple the human responses of the pilot to the aircraft control systems. The use of custom logic, e.g., graphics engines, may provide the processing power and architecture required for 3-D computer-generated imagery (CGI) or visual scene simulation (VSS). Diffraction or holographic head-up displays (HUDs) will also be integrated into the ACFS simulator to permit research on the requirements and use of these "out-the-window" projection systems. Future research may include the retrieval of high-resolution, perspective view terrain maps which could then be overlaid with current weather information or other selectable cultural features.

Molecular Genetics Information System (MOLGENIS): alternatives in developing local experimental genomics databases.

PubMed

Swertz, Morris A; De Brock, E O; Van Hijum, Sacha A F T; De Jong, Anne; Buist, Girbe; Baerends, Richard J S; Kok, Jan; Kuipers, Oscar P; Jansen, Ritsert C

2004-09-01

Genomic research laboratories need adequate infrastructure to support management of their data production and research workflow. But what makes infrastructure adequate? A lack of appropriate criteria makes any decision on buying or developing a system difficult. Here, we report on the decision process for the case of a molecular genetics group establishing a microarray laboratory. Five typical requirements for experimental genomics database systems were identified: (i) evolution ability to keep up with the fast developing genomics field; (ii) a suitable data model to deal with local diversity; (iii) suitable storage of data files in the system; (iv) easy exchange with other software; and (v) low maintenance costs. The computer scientists and the researchers of the local microarray laboratory considered alternative solutions for these five requirements and chose the following options: (i) use of automatic code generation; (ii) a customized data model based on standards; (iii) storage of datasets as black boxes instead of decomposing them in database tables; (iv) loosely linking to other programs for improved flexibility; and (v) a low-maintenance web-based user interface. Our team evaluated existing microarray databases and then decided to build a new system, Molecular Genetics Information System (MOLGENIS), implemented using code generation in a period of three months. This case can provide valuable insights and lessons to both software developers and a user community embarking on large-scale genomic projects. http://www.molgenis.nl

National Combustion Code: A Multidisciplinary Combustor Design System

NASA Technical Reports Server (NTRS)

Stubbs, Robert M.; Liu, Nan-Suey

1997-01-01

The Internal Fluid Mechanics Division conducts both basic research and technology, and system technology research for aerospace propulsion systems components. The research within the division, which is both computational and experimental, is aimed at improving fundamental understanding of flow physics in inlets, ducts, nozzles, turbomachinery, and combustors. This article and the following three articles highlight some of the work accomplished in 1996. A multidisciplinary combustor design system is critical for optimizing the combustor design process. Such a system should include sophisticated computer-aided design (CAD) tools for geometry creation, advanced mesh generators for creating solid model representations, a common framework for fluid flow and structural analyses, modern postprocessing tools, and parallel processing. The goal of the present effort is to develop some of the enabling technologies and to demonstrate their overall performance in an integrated system called the National Combustion Code.

ClinData Express – A Metadata Driven Clinical Research Data Management System for Secondary Use of Clinical Data

PubMed Central

Li, Zuofeng; Wen, Jingran; Zhang, Xiaoyan; Wu, Chunxiao; Li, Zuogao; Liu, Lei

2012-01-01

Aim to ease the secondary use of clinical data in clinical research, we introduce a metadata driven web-based clinical data management system named ClinData Express. ClinData Express is made up of two parts: 1) m-designer, a standalone software for metadata definition; 2) a web based data warehouse system for data management. With ClinData Express, what the researchers need to do is to define the metadata and data model in the m-designer. The web interface for data collection and specific database for data storage will be automatically generated. The standards used in the system and the data export modular make sure of the data reuse. The system has been tested on seven disease-data collection in Chinese and one form from dbGap. The flexibility of system makes its great potential usage in clinical research. The system is available at http://code.google.com/p/clindataexpress. PMID:23304327

Mental health research in the criminal justice system: The need for common approaches and international perspectives.

PubMed

Roesch, R; Ogloff, J R; Eaves, D

1995-01-01

There is a need for researchers and policy makers in the area of mental health and law to collaborate and develop common methods of approach to research. Although we have learned a great deal about the prevalence and needs of mentally ill offenders in jails and prisons, there are a number of research questions that remain. If the "second generation" of research is to be fruitful--and useful to policy makers--we need to be sure that the methods we employ are valid and that the findings we obtain are reliable. By collaborating with colleagues in other jurisdictions, we can begin to learn whether some of the existing findings are of a general nature, or dependent upon the system in which they were found. Similarly, while the first-generation research has alerted us to the needs of mentally ill offenders in jails and prisons, second-generation research is needed to help identify factors that may help prevent the "revolving door phenomenon," which results in mentally ill people being volleyed among mental health, criminal justice, and community settings. One area that has received embarrassingly little attention has been the need for considering the relationship between substance abuse and mental disorders. In our own work, we have found an alarmingly high degree of substance abuse among offenders, including mentally ill offenders. We have come to realize the importance of considering the role that substance abuse coupled with other mental disorders may play in the criminal justice system. As a result of this concern, the Surrey Mental Health Project recently hired a full-time drug and alcohol counselor whose job it is to work with inmates with substance abuse disorders while in the jail, and to help arrange continuing treatment resources upon their release. As Wilson et al. (1995) discuss, intensive case management projects may be particularly useful at targeting the unique needs of mentally ill offenders with multiple problems. Much of the research conducted with mentally ill offenders to date has focused primarily upon psychological and psychiatric questions--questions that are, as Hodgins (1995) indicates, epidemiological in nature. More attention must be paid to that research by policy makers and others who work with mentally ill offenders in the criminal justice system. As Hoyer et al. (1995) and Gould (1995) make clear, a number of unique policy questions arise when considering mentally ill offenders in the legal system.(ABSTRACT TRUNCATED AT 400 WORDS)

Generalist solutions to complex problems: generating practice-based evidence - the example of managing multi-morbidity

PubMed Central

2013-01-01

Background A growing proportion of people are living with long term conditions. The majority have more than one. Dealing with multi-morbidity is a complex problem for health systems: for those designing and implementing healthcare as well as for those providing the evidence informing practice. Yet the concept of multi-morbidity (the presence of >2 diseases) is a product of the design of health care systems which define health care need on the basis of disease status. So does the solution lie in an alternative model of healthcare? Discussion Strengthening generalist practice has been proposed as part of the solution to tackling multi-morbidity. Generalism is a professional philosophy of practice, deeply known to many practitioners, and described as expertise in whole person medicine. But generalism lacks the evidence base needed by policy makers and planners to support service redesign. The challenge is to fill this practice-research gap in order to critically explore if and when generalist care offers a robust alternative to management of this complex problem. We need practice-based evidence to fill this gap. By recognising generalist practice as a ‘complex intervention’ (intervening in a complex system), we outline an approach to evaluate impact using action-research principles. We highlight the implications for those who both commission and undertake research in order to tackle this problem. Summary Answers to the complex problem of multi-morbidity won’t come from doing more of the same. We need to change systems of care, and so the systems for generating evidence to support that care. This paper contributes to that work through outlining a process for generating practice-based evidence of generalist solutions to the complex problem of person-centred care for people with multi-morbidity. PMID:23919296

Generalist solutions to complex problems: generating practice-based evidence--the example of managing multi-morbidity.

PubMed

Reeve, Joanne; Blakeman, Tom; Freeman, George K; Green, Larry A; James, Paul A; Lucassen, Peter; Martin, Carmel M; Sturmberg, Joachim P; van Weel, Chris

2013-08-07

A growing proportion of people are living with long term conditions. The majority have more than one. Dealing with multi-morbidity is a complex problem for health systems: for those designing and implementing healthcare as well as for those providing the evidence informing practice. Yet the concept of multi-morbidity (the presence of >2 diseases) is a product of the design of health care systems which define health care need on the basis of disease status. So does the solution lie in an alternative model of healthcare? Strengthening generalist practice has been proposed as part of the solution to tackling multi-morbidity. Generalism is a professional philosophy of practice, deeply known to many practitioners, and described as expertise in whole person medicine. But generalism lacks the evidence base needed by policy makers and planners to support service redesign. The challenge is to fill this practice-research gap in order to critically explore if and when generalist care offers a robust alternative to management of this complex problem. We need practice-based evidence to fill this gap. By recognising generalist practice as a 'complex intervention' (intervening in a complex system), we outline an approach to evaluate impact using action-research principles. We highlight the implications for those who both commission and undertake research in order to tackle this problem. Answers to the complex problem of multi-morbidity won't come from doing more of the same. We need to change systems of care, and so the systems for generating evidence to support that care. This paper contributes to that work through outlining a process for generating practice-based evidence of generalist solutions to the complex problem of person-centred care for people with multi-morbidity.

SCALS: a fourth-generation study of assisted living technologies in their organisational, social, political and policy context.

PubMed

Greenhalgh, Trisha; Shaw, Sara; Wherton, Joe; Hughes, Gemma; Lynch, Jenni; A'Court, Christine; Hinder, Sue; Fahy, Nick; Byrne, Emma; Finlayson, Alexander; Sorell, Tom; Procter, Rob; Stones, Rob

2016-02-15

Research to date into assisted living technologies broadly consists of 3 generations: technical design, experimental trials and qualitative studies of the patient experience. We describe a fourth-generation paradigm: studies of assisted living technologies in their organisational, social, political and policy context. Fourth-generation studies are necessarily organic and emergent; they view technology as part of a dynamic, networked and potentially unstable system. They use co-design methods to generate and stabilise local solutions, taking account of context. SCALS (Studies in Co-creating Assisted Living Solutions) consists (currently) of 5 organisational case studies, each an English health or social care organisation striving to introduce technology-supported services to support independent living in people with health and/or social care needs. Treating these cases as complex systems, we seek to explore interdependencies, emergence and conflict. We employ a co-design approach informed by the principles of action research to help participating organisations establish, refine and evaluate their service. To that end, we are conducting in-depth ethnographic studies of people's experience of assisted living technologies (micro level), embedded in evolving organisational case studies that use interviews, ethnography and document analysis (meso level), and exploring the wider national and international context for assisted living technologies and policy (macro level). Data will be analysed using a sociotechnical framework developed from structuration theory. Research ethics approval for the first 4 case studies has been granted. An important outcome will be lessons learned from individual co-design case studies. We will document the studies' credibility and rigour, and assess the transferability of findings to other settings while also recognising unique aspects of the contexts in which they were generated. Academic outputs will include a cross-case analysis and progress in theory and method of fourth-generation assisted living technology research. We will produce practical guidance for organisations, policymakers, designers and service users. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

ART/Ada design project, phase 1. Task 3 report: Test plan

NASA Technical Reports Server (NTRS)

Allen, Bradley P.

1988-01-01

The plan is described for the integrated testing and benchmark of Phase Ada based ESBT Design Research Project. The integration testing is divided into two phases: (1) the modules that do not rely on the Ada code generated by the Ada Generator are tested before the Ada Generator is implemented; and (2) all modules are integrated and tested with the Ada code generated by the Ada Generator. Its performance and size as well as its functionality is verified in this phase. The target platform is a DEC Ada compiler on VAX mini-computers and VAX stations running the VMS operating system.

Planning applications in image analysis

NASA Technical Reports Server (NTRS)

Boddy, Mark; White, Jim; Goldman, Robert; Short, Nick, Jr.

1994-01-01

We describe two interim results from an ongoing effort to automate the acquisition, analysis, archiving, and distribution of satellite earth science data. Both results are applications of Artificial Intelligence planning research to the automatic generation of processing steps for image analysis tasks. First, we have constructed a linear conditional planner (CPed), used to generate conditional processing plans. Second, we have extended an existing hierarchical planning system to make use of durations, resources, and deadlines, thus supporting the automatic generation of processing steps in time and resource-constrained environments.

An electric generator using living Torpedo electric organs controlled by fluid pressure-based alternative nervous systems

PubMed Central

Tanaka, Yo; Funano, Shun-ichi; Nishizawa, Yohei; Kamamichi, Norihiro; Nishinaka, Masahiro; Kitamori, Takehiko

2016-01-01

Direct electric power generation using biological functions have become a research focus due to their low cost and cleanliness. Unlike major approaches using glucose fuels or microbial fuel cells (MFCs), we present a generation method with intrinsically high energy conversion efficiency and generation with arbitrary timing using living electric organs of Torpedo (electric rays) which are serially integrated electrocytes converting ATP into electric energy. We developed alternative nervous systems using fluid pressure to stimulate electrocytes by a neurotransmitter, acetylcholine (Ach), and demonstrated electric generation. Maximum voltage and current were 1.5 V and 0.64 mA, respectively, with a duration time of a few seconds. We also demonstrated energy accumulation in a capacitor. The current was far larger than that using general cells other than electrocytes (~pA level). The generation ability was confirmed against repetitive cycles and also after preservation for 1 day. This is the first step toward ATP-based energy harvesting devices. PMID:27241817

An electric generator using living Torpedo electric organs controlled by fluid pressure-based alternative nervous systems

NASA Astrophysics Data System (ADS)

Tanaka, Yo; Funano, Shun-Ichi; Nishizawa, Yohei; Kamamichi, Norihiro; Nishinaka, Masahiro; Kitamori, Takehiko

2016-05-01

Direct electric power generation using biological functions have become a research focus due to their low cost and cleanliness. Unlike major approaches using glucose fuels or microbial fuel cells (MFCs), we present a generation method with intrinsically high energy conversion efficiency and generation with arbitrary timing using living electric organs of Torpedo (electric rays) which are serially integrated electrocytes converting ATP into electric energy. We developed alternative nervous systems using fluid pressure to stimulate electrocytes by a neurotransmitter, acetylcholine (Ach), and demonstrated electric generation. Maximum voltage and current were 1.5 V and 0.64 mA, respectively, with a duration time of a few seconds. We also demonstrated energy accumulation in a capacitor. The current was far larger than that using general cells other than electrocytes (~pA level). The generation ability was confirmed against repetitive cycles and also after preservation for 1 day. This is the first step toward ATP-based energy harvesting devices.

Advanced Research Deposition System (ARDS) for processing CdTe solar cells

NASA Astrophysics Data System (ADS)

Barricklow, Keegan Corey

CdTe solar cells have been commercialized at the Gigawatt/year level. The development of volume manufacturing processes for next generation CdTe photovoltaics (PV) with higher efficiencies requires research systems with flexibility, scalability, repeatability and automation. The Advanced Research Deposition Systems (ARDS) developed by the Materials Engineering Laboratory (MEL) provides such a platform for the investigation of materials and manufacturing processes necessary to produce the next generation of CdTe PV. Limited by previous research systems, the ARDS was developed to provide process and hardware flexibility, accommodating advanced processing techniques, and capable of producing device quality films. The ARDS is a unique, in-line process tool with nine processing stations. The system was designed, built and assembled at the Materials Engineering Laboratory. Final assembly, startup, characterization and process development are the focus of this research. Many technical challenges encountered during the startup of the ARDS were addressed in this research. In this study, several hardware modifications needed for the reliable operation of the ARDS were designed, constructed and successfully incorporated into the ARDS. The effect of process condition on film properties for each process step was quantified. Process development to achieve 12% efficient baseline solar cell required investigation of discrete processing steps, troubleshooting process variation, and developing performance correlations. Subsequent to this research, many advances have been demonstrated with the ARDS. The ARDS consistently produces devices of 12% +/-.5% by the process of record (POR). The champion cell produced to date utilizing the ARDS has an efficiency of 16.2% on low cost commercial sodalime glass and utilizes advanced films. The ARDS has enabled investigation of advanced concepts for processing CdTe devices including, Plasma Cleaning, Plasma Enhanced Closed Space Sublimation (PECSS), Electron Reflector (ER) using Cd1-xMgxTe (CMT) structure and alternative device structures. The ARDS has been instrumental in the collaborative research with many institutions.

Hallmarks of cancer: The CRISPR generation.

PubMed

Moses, Colette; Garcia-Bloj, Benjamin; Harvey, Alan R; Blancafort, Pilar

2018-04-01

The hallmarks of cancer were proposed as a logical framework to guide research efforts that aim to understand the molecular mechanisms and derive treatments for this highly complex disease. Recent technological advances, including comprehensive sequencing of different cancer subtypes, have illuminated how genetic and epigenetic alterations are associated with specific hallmarks of cancer. However, as these associations are purely descriptive, one particularly exciting development is the emergence of genome editing technologies, which enable rapid generation of precise genetic and epigenetic modifications to assess the consequences of these perturbations on the cancer phenotype. The most recently developed of these tools, the system of Clustered Regularly Interspaced Short Palindromic Repeats (CRISPR), consists of an RNA-guided endonuclease that can be repurposed to edit both genome and epigenome with high specificity, and facilitates the functional interrogation of multiple loci in parallel. This system has the potential to dramatically accelerate progress in cancer research, whether by modelling the genesis and progression of cancer in vitro and in vivo, screening for novel therapeutic targets, conducting functional genomics/epigenomics, or generating targeted cancer therapies. Here, we discuss CRISPR research on each of the ten hallmarks of cancer, outline potential barriers for its clinical implementation and speculate on the advances it may allow in cancer research in the near future. Copyright © 2018 The Author(s). Published by Elsevier Ltd.. All rights reserved.

Energy Analysis of Offshore Systems | Wind | NREL

Science.gov Websites

successful research to understand and improve the cost of wind generation technology. As a research approaches used to estimate direct and indirect economic impacts of offshore wind. Chart of cost data for report on cost trends. Recent studies include: Analysis of capital cost trends for planned and installed

Photovoltaic Research | NREL

Science.gov Websites

the cost of solar cells, modules, and systems; and improving the reliability of PV components and Science-funded Center for Next Generation of Materials by Design. Reliability. Real-Time PV and Solar Research Solar panels line the rooftop of the parking garage at the south table mountain campus of

Bringing Installation Art to Reconnaissance to Share Values and Generate Action

ERIC Educational Resources Information Center

Townsend, Andrew; Thomson, Pat

2015-01-01

The English education system has recently seen something of a revival of enthusiasm for the use of research both to develop educational practices and to gather evidence about their effectiveness. These initiatives often present action research as a model of individual problem-solving, which, we argue, communicates a limited conception of action…

Research Plan for Study of Biological and Ecological Effects of the Solar Power Satellite Transmission System

NASA Technical Reports Server (NTRS)

Newsom, B. D.

1978-01-01

A programmatic research plan for a three year study is presented to generate knowledge on effects of the continuous wave 2.45 GHz microwave power transmission that the Solar Power Satellite might have on biological and ecological elements, within and around the rectenna receiving site.

Performance Rating Accuracy Improvement through Changes in Individual and System Characteristics.

ERIC Educational Resources Information Center

Kavanagh, Michael J.

Although the quest for better measurement of individual job performance has generated considerable empirical research in industrial and organizational psychology, the feeling persists that a good job is not really being done in measuring job performance. This research project investigated the effects of differences in both individual and systems…

A Program of Research and Education to Advance the Design, Synthesis, and Optimization of Aero-Space System Concepts

NASA Technical Reports Server (NTRS)

Sandusky, Robert

2002-01-01

Since its inception in December 1999, the program has provided support for a total of 11 Graduate Research Scholar Assistants, of these, 6 have completed their MS degree program. The program has generated 3 MS theses and a total of 4 publications/presentations.

A system for forecasting and monitoring cash flow : phase I : forecasting payments on construction contracts.

DOT National Transportation Integrated Search

1983-01-01

The research on which this paper is based was performed as part of a study to develop a system for generating a one-to-two year forecast of monthly cash flows for the Virginia Department of Highways and Transportation. It revealed that presently used...

Golden Rays - December 2016 | Solar Research | NREL

Science.gov Websites

CSP system. Next-generation Gen3 systems will incorporate high-temperature receivers and thermal able to quickly and effectively support each of these companies with technical assistance, on-site storage, cell manufacture, or installation methodologies. NREL supports each company with a unique scope

In the Face of Fallible AWE Feedback: How Do Students Respond?

ERIC Educational Resources Information Center

Bai, Lifang; Hu, Guangwei

2017-01-01

Automated writing evaluation (AWE) systems can provide immediate computer-generated quantitative assessments and qualitative diagnostic feedback on an enormous number of submitted essays. However, limited research attention has been paid to locally designed AWE systems used in English as a foreign language (EFL) classroom contexts. This study…

Designing a Decision-Support System for Enrollment Management. AIR 1985 Annual Forum Paper.

ERIC Educational Resources Information Center

Glover, Robert H.

University of Hartford's decision-support system for enrollment management, which uses fourth-generation software tools, is described, with attention to the conceptual framework, design and implementation plan, and progress to date. The university's planners, institutional researchers, and admissions and financial aid officers are cooperating in…

Classification Objects, Ideal Observers & Generative Models

ERIC Educational Resources Information Center

Olman, Cheryl; Kersten, Daniel

2004-01-01

A successful vision system must solve the problem of deriving geometrical information about three-dimensional objects from two-dimensional photometric input. The human visual system solves this problem with remarkable efficiency, and one challenge in vision research is to understand how neural representations of objects are formed and what visual…

Non-Symbolic Halving in an Amazonian Indigene Group

ERIC Educational Resources Information Center

McCrink, Koleen; Spelke, Elizabeth S.; Dehaene, Stanislas; Pica, Pierre

2013-01-01

Much research supports the existence of an Approximate Number System (ANS) that is recruited by infants, children, adults, and non-human animals to generate coarse, non-symbolic representations of number. This system supports simple arithmetic operations such as addition, subtraction, and ordering of amounts. The current study tests whether an…

NETL- High-Pressure Combustion Research Facility

ScienceCinema

None

2018-02-14

NETL's High-Pressure Combustion Facility is a unique resource within the National Laboratories system. It provides the test capabilities needed to evaluate new combustion concepts for high-pressure, high-temperature hydrogen and natural gas turbines. These concepts will be critical for the next generation of ultra clean, ultra efficient power systems.

The Newsroom to the Year 2001.

ERIC Educational Resources Information Center

Keirstead, Phillip O.

Projections for a possible scenario for a television broadcast newsroom in 2001 would include a nearly completely computerized system, one which will write scripts, select and create graphics, organize newscasts and visuals, keep records, do research, and manage the newsroom from terminals. This computer system will generate many more newscasts…

Content Based Retrieval Database Management System with Support for Similarity Searching and Query Refinement

DTIC Science & Technology

2002-01-01

to the OODBMS approach. The ORDBMS approach produced such research prototypes as Postgres [155], and Starburst [67] and commercial products such as...Kemnitz. The POSTGRES Next-Generation Database Management System. Communications of the ACM, 34(10):78–92, 1991. [156] Michael Stonebreaker and Dorothy

Equality of opportunities for next generation researchers: bridging the gap between theory and practice in Eastern Europe

NASA Astrophysics Data System (ADS)

Žagar, Nedjeljka; Alkauskas, Audrius; Gyürky, György; Heiri, Oliver; Robinson, Nathaniel D.; Schäfer, Thomas

2016-04-01

Twenty-five years after the fall of the Berlin wall and the historical opening of the European Union to the countries of Central and Eastern Europe, there is still a striking difference in the success of European countries in attracting research funds and talented researchers. A number of indicators document the differences in research success and research opportunities between Eastern and Western European countries, and even between Northern and Southern Europe. Differences, as described for example by a number of secured ERC grants, apply to all research fields and to researchers at all stages of their careers. While statistical analysis document large gradients in research performance across the continent, the underlying issues that young researchers struggle with are common across Europe, although they impact research environment to a different extent. These issues are presently being discussed within Sci-Generation, a COST Targeted Network that aims to enhance the European research environment for the next generation of young researchers. The major goal of the network is to contribute ideas towards overcoming these differences in opportunities across Europe. Targeting researchers in the early stage of their independent carrier or in the transition to independence, Sci-Generation is devoted to inclusiveness in order to represent a diversity of issues in science policy in Europe. In particular, the network's Working Group 1 focuses on the countries of Eastern and Southern Europe with less success in attracting European research funding. Among other issues, we considered the involvement of young researchers in decision-making processes at all levels important in order to increase the systems' transparency. As shown by an ongoing study of how language affects the evaluation of research applications, the use of the local language serves, in some cases, as one of the last stands of "science-managing elites" that grew up in systems before 1990. We discuss how a lack of research opportunities and "brain drain" in parts of Eastern Europe are not only due to economic constraints; but, on top of these challenges come opaque selection procedures that can keep even the most enthusiastic and "home sick" talented young researchers abroad. The atmospheric and ocean circulation know no borders, and it is thus not strange that the earliest international collaborations developed in meteorology. An example of the 20-year long collaboration in atmospheric sciences among countries of Central and Eastern Europe devoted to the improvement of numerical weather prediction will be presented with focus on its impact on applied sciences and the society.

Complexity, flow, and antifragile healthcare systems: implications for nurse executives.

PubMed

Clancy, Thomas R

2015-04-01

As systems evolve over time, their natural tendency is to become increasingly more complex. Studies in the field of complex systems have generated new perspectives on the application of management strategies in health systems. Much of this research appears as a natural extension of the cross-disciplinary field of systems theory. In this article, I further discuss the concept of fragility, its impact on system behavior, and ways to reduce it.

Next generation initiation techniques

NASA Technical Reports Server (NTRS)

Warner, Tom; Derber, John; Zupanski, Milija; Cohn, Steve; Verlinde, Hans

1993-01-01

Four-dimensional data assimilation strategies can generally be classified as either current or next generation, depending upon whether they are used operationally or not. Current-generation data-assimilation techniques are those that are presently used routinely in operational-forecasting or research applications. They can be classified into the following categories: intermittent assimilation, Newtonian relaxation, and physical initialization. It should be noted that these techniques are the subject of continued research, and their improvement will parallel the development of next generation techniques described by the other speakers. Next generation assimilation techniques are those that are under development but are not yet used operationally. Most of these procedures are derived from control theory or variational methods and primarily represent continuous assimilation approaches, in which the data and model dynamics are 'fitted' to each other in an optimal way. Another 'next generation' category is the initialization of convective-scale models. Intermittent assimilation systems use an objective analysis to combine all observations within a time window that is centered on the analysis time. Continuous first-generation assimilation systems are usually based on the Newtonian-relaxation or 'nudging' techniques. Physical initialization procedures generally involve the use of standard or nonstandard data to force some physical process in the model during an assimilation period. Under the topic of next-generation assimilation techniques, variational approaches are currently being actively developed. Variational approaches seek to minimize a cost or penalty function which measures a model's fit to observations, background fields and other imposed constraints. Alternatively, the Kalman filter technique, which is also under investigation as a data assimilation procedure for numerical weather prediction, can yield acceptable initial conditions for mesoscale models. The third kind of next-generation technique involves strategies to initialize convective scale (non-hydrostatic) models.

The Tension Between Data Sharing and the Protection of Privacy in Genomics Research

PubMed Central

Kaye, Jane

2014-01-01

Next-generation sequencing and global data sharing challenge many of the governance mechanisms currently in place to protect the privacy of research participants. These challenges will make it more difficult to guarantee anonymity for participants, provide information to satisfy the requirements of informed consent, and ensure complete withdrawal from research when requested. To move forward, we need to improve the current governance systems for research so that they are responsive to individual privacy concerns but can also be effective at a global level. We need to develop a system of e-governance that can complement existing governance systems but that places greater reliance on the use of technology to ensure compliance with ethical and legal requirements. These new governance structures must be able to address the concerns of research participants while at the same time ensuring effective data sharing that promotes public trust in genomics research. PMID:22404490

The tension between data sharing and the protection of privacy in genomics research.

PubMed

Kaye, Jane

2012-01-01

Next-generation sequencing and global data sharing challenge many of the governance mechanisms currently in place to protect the privacy of research participants. These challenges will make it more difficult to guarantee anonymity for participants, provide information to satisfy the requirements of informed consent, and ensure complete withdrawal from research when requested. To move forward, we need to improve the current governance systems for research so that they are responsive to individual privacy concerns but can also be effective at a global level. We need to develop a system of e-governance that can complement existing governance systems but that places greater reliance on the use of technology to ensure compliance with ethical and legal requirements. These new governance structures must be able to address the concerns of research participants while at the same time ensuring effective data sharing that promotes public trust in genomics research.

A concurrent distributed system for aircraft tactical decision generation

NASA Technical Reports Server (NTRS)

Mcmanus, John W.

1990-01-01

A research program investigating the use of AI techniques to aid in the development of a tactical decision generator (TDG) for within visual range (WVR) air combat engagements is discussed. The application of AI programming and problem-solving methods in the development and implementation of a concurrent version of the computerized logic for air-to-air warfare simulations (CLAWS) program, a second-generation TDG, is presented. Concurrent computing environments and programming approaches are discussed, and the design and performance of prototype concurrent TDG system (Cube CLAWS) are presented. It is concluded that the Cube CLAWS has provided a useful testbed to evaluate the development of a distributed blackboard system. The project has shown that the complexity of developing specialized software on a distributed, message-passing architecture such as the Hypercube is not overwhelming, and that reasonable speedups and processor efficiency can be achieved by a distributed blackboard system. The project has also highlighted some of the costs of using a distributed approach to designing a blackboard system.

CATS-based Agents That Err

NASA Technical Reports Server (NTRS)

Callantine, Todd J.

2002-01-01

This report describes preliminary research on intelligent agents that make errors. Such agents are crucial to the development of novel agent-based techniques for assessing system safety. The agents extend an agent architecture derived from the Crew Activity Tracking System that has been used as the basis for air traffic controller agents. The report first reviews several error taxonomies. Next, it presents an overview of the air traffic controller agents, then details several mechanisms for causing the agents to err in realistic ways. The report presents a performance assessment of the error-generating agents, and identifies directions for further research. The research was supported by the System-Wide Accident Prevention element of the FAA/NASA Aviation Safety Program.

Dispatches from the Interface of Salivary Bioscience and Neonatal Research

PubMed Central

Voegtline, Kristin M.; Granger, Douglas A.

2014-01-01

The emergence of the interdisciplinary field of salivary bioscience has created opportunity for neonatal researchers to measure multiple components of biological systems non-invasively in oral fluids. The implications are profound and potentially high impact. From a single oral fluid specimen, information can be obtained about a vast array of biological systems (e.g., endocrine, immune, autonomic nervous system) and the genetic polymorphisms related to individual differences in their function. The purpose of this review is to describe the state of the art for investigators interested in integrating these unique measurement tools into the current and next generation of research on gonadal steroid exposure during the prenatal and neonatal developmental periods. PMID:24624119

Research on Experiment of Islanding Protection Device of Grid-connected Photovoltaic System Based on RTDS

NASA Astrophysics Data System (ADS)

Zhou, Ning; Yang, Jia; Cheng, Zheng; Chen, Bo; Su, Yong Chun; Shu, Zhan; Zou, Jin

2017-06-01

Solar photovoltaic power generation is the power generation using solar cell module converting sunlight into DC electric energy. In the paper an equivalent model of solar photovoltaic power generation system is built in RTDS. The main circuit structure of the two-stage PV grid-connected system consists of the DC-DC, DC-AC circuit. The MPPT (Maximum Power Point Tracking) control of the PV array is controlled by adjusting the duty ratio of the DC-DC circuit. The proposed control strategy of constant voltage/constant reactive power (V/Q) control is successfully implemented grid-connected control of the inverter when grid-connected operation. The closed-loop experiment of islanding protection device of photovoltaic power plant on RTDS, verifies the correctness of the simulation model, and the experimental verification can be applied to this type of device.

Projected Applications of a "Weather in a Box" Computing System at the NASA Short-Term Prediction Research and Transition (SPoRT) Center

NASA Technical Reports Server (NTRS)

Jedlovec, Gary J.; Molthan, Andrew; Zavodsky, Bradley T.; Case, Jonathan L.; LaFontaine, Frank J.; Srikishen, Jayanthi

2010-01-01

The NASA Short-term Prediction Research and Transition Center (SPoRT)'s new "Weather in a Box" resources will provide weather research and forecast modeling capabilities for real-time application. Model output will provide additional forecast guidance and research into the impacts of new NASA satellite data sets and software capabilities. By combining several research tools and satellite products, SPoRT can generate model guidance that is strongly influenced by unique NASA contributions.

Automation of steam generator services at public service electric & gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cruickshank, H.; Wray, J.; Scull, D.

1995-03-01

Public Service Electric & Gas takes an aggressive approach to pursuing new exposure reduction techniques. Evaluation of historic outage exposure shows that over the last eight refueling outages, primary steam generator work has averaged sixty-six (66) person-rem, or, approximately tewenty-five percent (25%) of the general outage exposure at Salem Station. This maintenance evolution represents the largest percentage of exposure for any single activity. Because of this, primary steam generator work represents an excellent opportunity for the development of significant exposure reduction techniques. A study of primary steam generator maintenance activities demonstrated that seventy-five percent (75%) of radiation exposure was duemore » to work activities of the primary steam generator platform, and that development of automated methods for performing these activities was worth pursuing. Existing robotics systems were examined and it was found that a new approach would have to be developed. This resulted in a joint research and development project between Westinghouse and Public Service Electric & Gas to develop an automated system of accomplishing the Health Physics functions on the primary steam generator platform. R.O.M.M.R.S. (Remotely Operated Managed Maintenance Robotics System) was the result of this venture.« less

Ontology-Based Multiple Choice Question Generation

PubMed Central

Al-Yahya, Maha

2014-01-01

With recent advancements in Semantic Web technologies, a new trend in MCQ item generation has emerged through the use of ontologies. Ontologies are knowledge representation structures that formally describe entities in a domain and their relationships, thus enabling automated inference and reasoning. Ontology-based MCQ item generation is still in its infancy, but substantial research efforts are being made in the field. However, the applicability of these models for use in an educational setting has not been thoroughly evaluated. In this paper, we present an experimental evaluation of an ontology-based MCQ item generation system known as OntoQue. The evaluation was conducted using two different domain ontologies. The findings of this study show that ontology-based MCQ generation systems produce satisfactory MCQ items to a certain extent. However, the evaluation also revealed a number of shortcomings with current ontology-based MCQ item generation systems with regard to the educational significance of an automatically constructed MCQ item, the knowledge level it addresses, and its language structure. Furthermore, for the task to be successful in producing high-quality MCQ items for learning assessments, this study suggests a novel, holistic view that incorporates learning content, learning objectives, lexical knowledge, and scenarios into a single cohesive framework. PMID:24982937

River Devices to Recover Energy with Advanced Materials (River DREAM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMahon, Daniel P.

2013-07-03

The purpose of this project is to develop a generator called a Galloping Hydroelectric Energy Extraction Device (GHEED). It uses a galloping prism to convert water flow into linear motion. This motion is converted into electricity via a dielectric elastomer generator (DEG). The galloping mechanism and the DEG are combined to create a system to effectively generate electricity. This project has three research objectives: 1. Oscillator development and design a. Characterize galloping behavior, evaluate control surface shape change on oscillator performance and demonstrate shape change with water flow change. 2. Dielectric Energy Generator (DEG) characterization and modeling a. Characterize andmore » model the performance of the DEG based on oscillator design 3. Galloping Hydroelectric Energy Extraction Device (GHEED) system modeling and integration a. Create numerical models for construction of a system performance model and define operating capabilities for this approach Accomplishing these three objectives will result in the creation of a model that can be used to fully define the operating parameters and performance capabilities of a generator based on the GHEED design. This information will be used in the next phase of product development, the creation of an integrated laboratory scale generator to confirm model predictions.« less

A pragmatic method for transforming clinical research data from the research electronic data capture "REDCap" to Clinical Data Interchange Standards Consortium (CDISC) Study Data Tabulation Model (SDTM): Development and evaluation of REDCap2SDTM.

PubMed

Yamamoto, Keiichi; Ota, Keiko; Akiya, Ippei; Shintani, Ayumi

2017-06-01

The Clinical Data Interchange Standards Consortium (CDISC) Study Data Tabulation Model (SDTM) can be used for new drug application studies as well as secondarily for creating a clinical research data warehouse to leverage clinical research study data across studies conducted within the same disease area. However, currently not all clinical research uses Clinical Data Acquisition Standards Harmonization (CDASH) beginning in the set-up phase of the study. Once already initiated, clinical studies that have not utilized CDASH are difficult to map in the SDTM format. In addition, most electronic data capture (EDC) systems are not equipped to export data in SDTM format; therefore, in many cases, statistical software is used to generate SDTM datasets from accumulated clinical data. In order to facilitate efficient secondary use of accumulated clinical research data using SDTM, it is necessary to develop a new tool to enable mapping of information for SDTM, even during or after the clinical research. REDCap is an EDC system developed by Vanderbilt University and is used globally by over 2100 institutions across 108 countries. In this study, we developed a simulated clinical trial to evaluate a tool called REDCap2SDTM that maps information in the Field Annotation of REDCap to SDTM and executes data conversion, including when data must be pivoted to accommodate the SDTM format, dynamically, by parsing the mapping information using R. We confirmed that generating SDTM data and the define.xml file from REDCap using REDCap2SDTM was possible. Conventionally, generation of SDTM data and the define.xml file from EDC systems requires the creation of individual programs for each clinical study. However, our proposed method can be used to generate this data and file dynamically without programming because it only involves entering the mapping information into the Field Annotation, and additional data into specific files. Our proposed method is adaptable not only to new drug application studies but also to all types of research, including observational and public health studies. Our method is also adaptable to clinical data collected with CDASH at the beginning of a study in non-standard format. We believe that this tool will reduce the workload of new drug application studies and will support data sharing and reuse of clinical research data in academia. Copyright © 2017 Elsevier Inc. All rights reserved.

Numerical simulation and experimental research on interaction of micro-defects and laser ultrasonic signal

NASA Astrophysics Data System (ADS)

Guo, Hualing; Zheng, Bin; Liu, Hui

2017-11-01

In the present research, the mechanism governing the interaction between laser-generated ultrasonic wave and the micro-defects on an aluminum plate has been studied by virtue of numerical simulation as well as practical experiments. Simulation results indicate that broadband ultrasonic waves are caused mainly by surface waves, and that the surface waves produced by micro-defects could be utilized for the detection of micro-defects because these waves reflect as much information of the defects as possible. In the research, a laser-generated ultrasonic wave testing system with a surface wave probe has been established for the detection of micro-defects, and the surface waves produced by the defects with different depths on an aluminum plate have been tested by using the system. The interaction between defect depth and the maximum amplitude of the surface wave and that between defect depth and the center frequency of the surface wave have also been analyzed in detail. Research results indicate that, when the defect depth is less than half of the wavelength of the surface wave, the maximum amplitude and the center frequency of the surface wave are in linear proportion to the defect depth. Sound consistency of experimental results with theoretical simulation indicates that the system as established in the present research could be adopted for the quantitative detection of micro-defects.

Thermodynamics Analysis of Binary Plant Generating Power from Low-Temperature Geothermal Resource

NASA Astrophysics Data System (ADS)

Maksuwan, A.

2018-05-01

The purpose in this research was to predict tendency of increase Carnot efficiency of the binary plant generating power from low-temperature geothermal resource. Low-temperature geothermal resources or less, are usually exploited by means of binary-type energy conversion systems. The maximum efficiency is analyzed for electricity production of the binary plant generating power from low-temperature geothermal resource becomes important. By using model of the heat exchanger equivalent to a power plant together with the calculation of the combined heat and power (CHP) generation. The CHP was solved in detail with appropriate boundary originating an idea from the effect of temperature of source fluid inlet-outlet and cooling fluid supply. The Carnot efficiency from the CHP calculation was compared between condition of increase temperature of source fluid inlet-outlet and decrease temperature of cooling fluid supply. Result in this research show that the Carnot efficiency for binary plant generating power from low-temperature geothermal resource has tendency increase by decrease temperature of cooling fluid supply.

Progress in energy generation for Canadian remote sites

NASA Astrophysics Data System (ADS)

Saad, Y.; Younes, R.; Abboudi, S.; Ilinca, A.; Nohra, C.

2016-07-01

Many remote areas around the world are isolated, for various reasons, from electricity networks. They are usually supplied with electricity through diesel generators. The cost of operation and transportation of diesel fuel in addition to its price have led to the procurement of a more efficient and environmentally greener method of supply. Various studies have shown that a wind-diesel hybrid system with compressed air storage (WDCAS) seems to be one of the best solutions, and presents itself as an optimal configuration for the electrification of isolated sites. This system allows significant fuel savings to be made because the stored compressed air is used to supercharge the engine. In order to optimize system performance and minimize fuel consumption, installation of a system for recovering and storing the heat of compression (TES) seems necessary. In addition, the use of hydro-pneumatic energy storage systems that use the same machine as the hydraulic pump and turbine allow us to store energy in tight spaces and, if possible, contribute to power generation. The scrupulous study of this technical approach will be the focus of our research which will validate (or not) the use of such a system for the regulation of frequency of electrical networks. In this article we will skim through the main research that recently examined the wind-diesel hybrid system which addressed topics such as adiabatic compression and hydro-pneumatic storage. Instead, we will offer (based on existing studies) a new ACP-WDCAS (wind-diesel hybrid system with adiabatic air compression and storage at constant pressure), which combines these three concepts in one system for the optimization of wind-diesel hybrid system.

Intelligent scheduling of execution for customized physical fitness and healthcare system.

PubMed

Huang, Chung-Chi; Liu, Hsiao-Man; Huang, Chung-Lin

2015-01-01

Physical fitness and health of white collar business person is getting worse and worse in recent years. Therefore, it is necessary to develop a system which can enhance physical fitness and health for people. Although the exercise prescription can be generated after diagnosing for customized physical fitness and healthcare. It is hard to meet individual execution needs for general scheduling of physical fitness and healthcare system. So the main purpose of this research is to develop an intelligent scheduling of execution for customized physical fitness and healthcare system. The results of diagnosis and prescription for customized physical fitness and healthcare system will be generated by fuzzy logic Inference. Then the results of diagnosis and prescription for customized physical fitness and healthcare system will be scheduled and executed by intelligent computing. The scheduling of execution is generated by using genetic algorithm method. It will improve traditional scheduling of exercise prescription for physical fitness and healthcare. Finally, we will demonstrate the advantages of the intelligent scheduling of execution for customized physical fitness and healthcare system.

Chemistry of the Konica Dry Color System

NASA Astrophysics Data System (ADS)

Suda, Yoshihiko; Ohbayashi, Keiji; Onodera, Kaoru

1991-08-01

While silver halide photosensitive materials offer superiority in image quality -- both in color and black-and-white -- they require chemical solutions for processing, and this can be a drawback. To overcome this, researchers turned to the thermal development of silver halide photographic materials, and met their first success with black-and-white images. Later, with the development of the Konica Dry Color System, color images were finally obtained from a completely dry thermal development system, without the use of water or chemical solutions. The dry color system is characterized by a novel chromogenic color image-forming technology and comprises four processes. (1) With the application of heat, a color developer precursor (CDP) decomposes to generate a p-phenylenediamine color developer (CD). (2) The CD then develops silver salts. (3) Oxidized CD then reacts with couplers to generate color image dyes. (4) Finally, the dyes diffuse from the system's photosensitive sheet to its image-receiving sheet. The authors have analyzed the kinetics of each of the system's four processes. In this paper, they report the kinetics of the system's first process, color developer (CD) generation.

An Overview and Status of NASA's Radioisotope Power Conversion Technology NRA

NASA Technical Reports Server (NTRS)

Anderson, David J.; Wong, Wayne A.; Tuttle, Karen L.

2005-01-01

NASA's Advanced Radioisotope Power Systems (RPS) development program is developing next generation radioisotope power conversion technologies that will enable future missions that have requirements that can not be met by either photovoltaic systems or by current Radioisotope Power System (RPS) technology. The Advanced Power Conversion Research and Technology project of the Advanced RPS development program is funding research and technology activities through the NASA Research Announcement (NRA) 02-OSS-01, "Research Opportunities in Space Science 2002" entitled "Radioisotope Power Conversion Technology" (RPCT), August 13, 2002. The objective of the RPCT NRA is to advance the development of radioisotope power conversion technologies to provide significant improvements over the state-of-practice General Purpose Heat Source/Radioisotope Thermoelectric Generator by providing significantly higher efficiency to reduce the number of radioisotope fuel modules, and increase specific power (watts/kilogram). Other Advanced RPS goals include safety, long-life, reliability, scalability, multi-mission capability, resistance to radiation, and minimal interference with the scientific payload. Ten RPCT NRA contracts were awarded in 2003 in the areas of Brayton, Stirling, thermoelectric (TE), and thermophotovoltaic (TPV) power conversion technologies. This paper will provide an overview of the RPCT NRA, and a brief summary of accomplishments over the first 18 months but focusing on advancements made over the last 6 months.

GeneLab for High Schools: Data Mining for the Next Generation

NASA Technical Reports Server (NTRS)

Blaber, Elizabeth A.; Ly, Diana; Sato, Kevin Y.; Taylor, Elizabeth

2016-01-01

Modern biological sciences have become increasingly based on molecular biology and high-throughput molecular techniques, such as genomics, transcriptomics, and proteomics. NASA Scientists and the NASA Space Biology Program have aimed to examine the fundamental building blocks of life (RNA, DNA and protein) in order to understand the response of living organisms to space and aid in fundamental research discoveries on Earth. In an effort to enable NASA funded science to be available to everyone, NASA has collected the data from omics studies and curated them in a data system called GeneLab. Whilst most college-level interns, academics and other scientists have had some interaction with omics data sets and analysis tools, high school students often have not. Therefore, the Space Biology Program is implementing a new Summer Program for high-school students that aims to inspire the next generation of scientists to learn about and get involved in space research using GeneLabs Data System. The program consists of three main components core learning modules, focused on developing students knowledge on the Space Biology Program and Space Biology research, Genelab and the data system, and previous research conducted on model organisms in space; networking and team work, enabling students to interact with guest lecturers from local universities and their fellow peers, and also enabling them to visit local universities and genomics centers around the Bay area; and finally an independent learning project, whereby students will be required to form small groups, analyze a dataset on the Genelab platform, generate a hypothesis and develop a research plan to test their hypothesis. This program will not only help inspire high-school students to become involved in space-based research but will also help them develop key critical thinking and bioinformatics skills required for most college degrees and furthermore, will enable them to establish networks with their peers and connections with university Professors that may help them achieve their educational goals.

The development of ORACLe: a measure of an organisation's capacity to engage in evidence-informed health policy.

PubMed

Makkar, Steve R; Turner, Tari; Williamson, Anna; Louviere, Jordan; Redman, Sally; Haynes, Abby; Green, Sally; Brennan, Sue

2016-01-14

Evidence-informed policymaking is more likely if organisations have cultures that promote research use and invest in resources that facilitate staff engagement with research. Measures of organisations' research use culture and capacity are needed to assess current capacity, identify opportunities for improvement, and examine the impact of capacity-building interventions. The aim of the current study was to develop a comprehensive system to measure and score organisations' capacity to engage with and use research in policymaking, which we entitled ORACLe (Organisational Research Access, Culture, and Leadership). We used a multifaceted approach to develop ORACLe. Firstly, we reviewed the available literature to identify key domains of organisational tools and systems that may facilitate research use by staff. We interviewed senior health policymakers to verify the relevance and applicability of these domains. This information was used to generate an interview schedule that focused on seven key domains of organisational capacity. The interview was pilot-tested within four Australian policy agencies. A discrete choice experiment (DCE) was then undertaken using an expert sample to establish the relative importance of these domains. This data was used to produce a scoring system for ORACLe. The ORACLe interview was developed, comprised of 23 questions addressing seven domains of organisational capacity and tools that support research use, including (1) documented processes for policymaking; (2) leadership training; (3) staff training; (4) research resources (e.g. database access); and systems to (5) generate new research, (6) undertake evaluations, and (7) strengthen relationships with researchers. From the DCE data, a conditional logit model was estimated to calculate total scores that took into account the relative importance of the seven domains. The model indicated that our expert sample placed the greatest importance on domains (2), (3) and (4). We utilised qualitative and quantitative methods to develop a system to assess and score organisations' capacity to engage with and apply research to policy. Our measure assesses a broad range of capacity domains and identifies the relative importance of these capacities. ORACLe data can be used by organisations keen to increase their use of evidence to identify areas for further development.

2007 Research and Technology

NASA Technical Reports Server (NTRS)

Riddlebaugh, Stephen M. (Editor)

2008-01-01

The NASA Glenn Research Center is pushing the envelope of research and technology in aeronautics, space exploration, science, and space operations. Our research in aeropropulsion, structures and materials, and instrumentation and controls is enabling next-generation transportation systems that are faster, more environmentally friendly, more fuel efficient, and safer. Our research and development of space flight systems is enabling advanced power, propulsion, communications, and human health systems that will advance the exploration of our solar system. This report selectively summarizes NASA Glenn Research Center s research and technology accomplishments for fiscal year 2007. Comprising 104 short articles submitted by the staff scientists and engineers, the report is organized into six major sections: Aeropropulsion, Power and Space Propulsion, Communications, Space Processes and Experiments, Instrumentation and Controls, and Structures and Materials. It is not intended to be a comprehensive summary of all the research and technology work done over the past fiscal year; most of the work is reported in Glenn-published technical reports, journal articles, and presentations. For each article in this report, a Glenn contact person has been identified, and where possible, a reference document is listed so that additional information can be easily obtained.

Potential of Micro Hydroelectric Generator Embedded at 30,000 PE Effluent Discharge of Sewerage Treatment Plant

NASA Astrophysics Data System (ADS)

Che Munaaim, M. A.; Razali, N.; Ayob, A.; Hamidin, N.; Othuman Mydin, M. A.

2018-03-01

A micro hydroelectric generator is an energy conversion approach to generate electricity from potential (motion) energy to an electrical energy. In this research, it is desired to be implemented by using a micro hydroelectric generator which is desired to be embedded at the continuous flow of effluent discharge point of domestic sewerage treatment plant (STP). This research evaluates the potential of electricity generation from micro hydroelectric generator attached to 30,000 PE sewerage treatment plant. The power output obtained from calculation of electrical power conversion is used to identify the possibility of this system and its ability to provide electrical energy, which can minimize the cost of electric bill especially for the pumping system. The overview of this system on the practical application with the consideration of payback period is summarized. The ultimate aim of the whole application is to have a self-ecosystem electrical power generated for the internal use of STP by using its own flowing water in supporting the sustainable engineering towards renewable energy and energy efficient approach. The results shows that the output power obtained is lower than expected output power (12 kW) and fall beyond of the range of a micro hydro power (5kW - 100kW) since it is only generating 1.58 kW energy by calculation. It is also observed that the estimated payback period is longer which i.e 7 years to recoup the return of investment. A range of head from 4.5 m and above for the case where the flow shall at least have maintained at 0.05 m3/s in the selected plant in order to achieved a feasible power output. In conclusion, wastewater treatment process involves the flowing water (potential energy) especially at the effluent discharge point of STP is possibly harvested for electricity generation by embedding the micro hydroelectric generator. However, the selection of STP needs to have minimum 4.5 meter head with 0.05 m3/s of continuously flowing water to make it feasible to harvest.