Geologic Framework Model Analysis Model Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. Clayton

2000-12-19

The purpose of this report is to document the Geologic Framework Model (GFM), Version 3.1 (GFM3.1) with regard to data input, modeling methods, assumptions, uncertainties, limitations, and validation of the model results, qualification status of the model, and the differences between Version 3.1 and previous versions. The GFM represents a three-dimensional interpretation of the stratigraphy and structural features of the location of the potential Yucca Mountain radioactive waste repository. The GFM encompasses an area of 65 square miles (170 square kilometers) and a volume of 185 cubic miles (771 cubic kilometers). The boundaries of the GFM were chosen to encompassmore » the most widely distributed set of exploratory boreholes (the Water Table or WT series) and to provide a geologic framework over the area of interest for hydrologic flow and radionuclide transport modeling through the unsaturated zone (UZ). The depth of the model is constrained by the inferred depth of the Tertiary-Paleozoic unconformity. The GFM was constructed from geologic map and borehole data. Additional information from measured stratigraphy sections, gravity profiles, and seismic profiles was also considered. This interim change notice (ICN) was prepared in accordance with the Technical Work Plan for the Integrated Site Model Process Model Report Revision 01 (CRWMS M&O 2000). The constraints, caveats, and limitations associated with this model are discussed in the appropriate text sections that follow. The GFM is one component of the Integrated Site Model (ISM) (Figure l), which has been developed to provide a consistent volumetric portrayal of the rock layers, rock properties, and mineralogy of the Yucca Mountain site. The ISM consists of three components: (1) Geologic Framework Model (GFM); (2) Rock Properties Model (RPM); and (3) Mineralogic Model (MM). The ISM merges the detailed project stratigraphy into model stratigraphic units that are most useful for the primary downstream models and the repository design. These downstream models include the hydrologic flow models and the radionuclide transport models. All the models and the repository design, in turn, will be incorporated into the Total System Performance Assessment (TSPA) of the potential radioactive waste repository block and vicinity to determine the suitability of Yucca Mountain as a host for the repository. The interrelationship of the three components of the ISM and their interface with downstream uses are illustrated in Figure 2.« less

Estimate of the Reliability in Geological Forecasts for Tunnels: Toward a Structured Approach

NASA Astrophysics Data System (ADS)

Perello, Paolo

2011-11-01

In tunnelling, a reliable geological model often allows providing an effective design and facing the construction phase without unpleasant surprises. A geological model can be considered reliable when it is a valid support to correctly foresee the rock mass behaviour, therefore preventing unexpected events during the excavation. The higher the model reliability, the lower the probability of unforeseen rock mass behaviour. Unfortunately, owing to different reasons, geological models are affected by uncertainties and a fully reliable knowledge of the rock mass is, in most cases, impossible. Therefore, estimating to which degree a geological model is reliable, becomes a primary requirement in order to save time and money and to adopt the appropriate construction strategy. The definition of the geological model reliability is often achieved by engineering geologists through an unstructured analytical process and variable criteria. This paper focusses on geological models for projects of linear underground structures and represents an effort to analyse and include in a conceptual framework the factors influencing such models. An empirical parametric procedure is then developed with the aim of obtaining an index called "geological model rating (GMR)", which can be used to provide a more standardised definition of a geological model reliability.

Geologic framework of the long bay inner shelf: implications for coastal evolution in South Carolina

USGS Publications Warehouse

Barnhardt, W.; Denny, J.; Baldwin, W.; Schwab, W.; Morton, R.; Gayes, P.; Driscoll, N.

2007-01-01

The inner continental shelf off northern South Carolina is a sediment-limited environment characterized by extensive hardground areas, where coastal plain strata and ancient channel-fill deposits are exposed at the sea floor. Holocene sand is concentrated in large shoals associated with active tidal inlets, an isolated shore-detached sand body, and a widespread series of low-relief sand ridges. The regional geologic framework is a strong control on the production, movement and deposition of sediment. High-resolution geologic mapping of the sea floor supports conceptual models indicative of net southwestward sediment transport along the coast.

How much can we trust a geological model underlying a subsurface hydrological investigation?

NASA Astrophysics Data System (ADS)

Wellmann, Florian; de la Varga, Miguel; Schaaf, Alexander; Burs, David

2017-04-01

Geological models often provide an important basis for subsequent hydrological investigations. As these models are generally built with a limited amount of information, they can contain significant uncertainties - and it is reasonable to assume that these uncertainties can potentially influence subsequent hydrological simulations. However, the investigation of uncertainties in geological models is not straightforward - and, even though recent advances have been made in the field, there is no out-of-the-box implementation to analyze uncertainties in a standard geological modeling package. We present here results of recent developments to address this problem with an efficient implementation of a geological modeling method for complex structural models, integrated in a Bayesian inference framework. The implemented geological modeling approach is based on a full 3-D implicit interpolation that directly respects interface positions and orientation measurements, as well as the influence of faults. In combination, the approach allows us to generate ensembles of geological model realizations, constrained by additional information in the form of likelihood functions to ensure consistency with additional geological aspects (e.g. sequence continuity, topology, fault network consistency), and we demonstrate the potential of the method in an exemplified case study. With this approach, we aim to contribute to a better understanding of the influence of geological uncertainties on subsurface hydrological investigations.

A Geospatial Information Grid Framework for Geological Survey.

PubMed

Wu, Liang; Xue, Lei; Li, Chaoling; Lv, Xia; Chen, Zhanlong; Guo, Mingqiang; Xie, Zhong

2015-01-01

The use of digital information in geological fields is becoming very important. Thus, informatization in geological surveys should not stagnate as a result of the level of data accumulation. The integration and sharing of distributed, multi-source, heterogeneous geological information is an open problem in geological domains. Applications and services use geological spatial data with many features, including being cross-region and cross-domain and requiring real-time updating. As a result of these features, desktop and web-based geographic information systems (GISs) experience difficulties in meeting the demand for geological spatial information. To facilitate the real-time sharing of data and services in distributed environments, a GIS platform that is open, integrative, reconfigurable, reusable and elastic would represent an indispensable tool. The purpose of this paper is to develop a geological cloud-computing platform for integrating and sharing geological information based on a cloud architecture. Thus, the geological cloud-computing platform defines geological ontology semantics; designs a standard geological information framework and a standard resource integration model; builds a peer-to-peer node management mechanism; achieves the description, organization, discovery, computing and integration of the distributed resources; and provides the distributed spatial meta service, the spatial information catalog service, the multi-mode geological data service and the spatial data interoperation service. The geological survey information cloud-computing platform has been implemented, and based on the platform, some geological data services and geological processing services were developed. Furthermore, an iron mine resource forecast and an evaluation service is introduced in this paper.

A Geospatial Information Grid Framework for Geological Survey

PubMed Central

Wu, Liang; Xue, Lei; Li, Chaoling; Lv, Xia; Chen, Zhanlong; Guo, Mingqiang; Xie, Zhong

2015-01-01

The use of digital information in geological fields is becoming very important. Thus, informatization in geological surveys should not stagnate as a result of the level of data accumulation. The integration and sharing of distributed, multi-source, heterogeneous geological information is an open problem in geological domains. Applications and services use geological spatial data with many features, including being cross-region and cross-domain and requiring real-time updating. As a result of these features, desktop and web-based geographic information systems (GISs) experience difficulties in meeting the demand for geological spatial information. To facilitate the real-time sharing of data and services in distributed environments, a GIS platform that is open, integrative, reconfigurable, reusable and elastic would represent an indispensable tool. The purpose of this paper is to develop a geological cloud-computing platform for integrating and sharing geological information based on a cloud architecture. Thus, the geological cloud-computing platform defines geological ontology semantics; designs a standard geological information framework and a standard resource integration model; builds a peer-to-peer node management mechanism; achieves the description, organization, discovery, computing and integration of the distributed resources; and provides the distributed spatial meta service, the spatial information catalog service, the multi-mode geological data service and the spatial data interoperation service. The geological survey information cloud-computing platform has been implemented, and based on the platform, some geological data services and geological processing services were developed. Furthermore, an iron mine resource forecast and an evaluation service is introduced in this paper. PMID:26710255

Geologic Setting and Hydrogeologic Units of the Columbia Plateau Regional Aquifer System, Washington, Oregon, and Idaho

USGS Publications Warehouse

Kahle, Sue C.; Olsen, Theresa D.; Morgan, David S.

2009-01-01

The Columbia Plateau Regional Aquifer System (CPRAS) covers approximately 44,000 square miles of northeastern Oregon, southeastern Washington, and western Idaho. The area supports a $6 billion per year agricultural industry, leading the Nation in production of apples and nine other commodities (State of Washington Office of Financial Management, 2007; U.S. Department of Agriculture, 2007). Groundwater availability in the aquifers of the area is a critical water-resource management issue because the water demand for agriculture, economic development, and ecological needs is high. The primary aquifers of the CPRAS are basalts of the Columbia River Basalt Group (CRBG) and overlying basin-fill sediments. Water-resources issues that have implications for future groundwater availability in the region include (1) widespread water-level declines associated with development of groundwater resources for irrigation and other uses, (2) reduction in base flow to rivers and associated effects on temperature and water quality, and (3) current and anticipated effects of global climate change on recharge, base flow, and ultimately, groundwater availability. As part of a National Groundwater Resources Program, the U.S. Geological Survey began a study of the CPRAS in 2007 with the broad goals of (1) characterizing the hydrologic status of the system, (2) identifying trends in groundwater storage and use, and (3) quantifying groundwater availability. The study approach includes documenting changes in the status of the system, quantifying the hydrologic budget for the system, updating the regional hydrogeologic framework, and developing a groundwater-flow simulation model for the system. The simulation model will be used to evaluate and test the conceptual model of the system and later to evaluate groundwater availability under alternative development and climate scenarios. The objectives of this study were to update the hydrogeologic framework for the CPRAS using the available geologic mapping and well information and to develop a digital, three-dimensional hydrogeologic model that could be used as the basis of a groundwater-flow model. This report describes the principal geologic and hydrogeologic units of the CPRAS and geologic map and well data that were compiled as part of the study. The report also describes simplified regional hydrogeologic sections and unit extent maps that were used to conceptualize the framework prior to development of the digital 3-dimensional framework model.

Introduction to selected references on fossil fuels of the central and southern Appalachian basin: Chapter H.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ruppert, Leslie F.; Lentz, Erika E.; Tewalt, Susan J.; Román Colón, Yomayra A.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The Appalachian basin contains abundant coal and petroleum resources that have been studied and extracted for at least 150 years. In this volume, U.S. Geological Survey (USGS) scientists describe the geologic framework and geochemical character of the fossil-fuel resources of the central and southern Appalachian basin. Separate subchapters (some previously published) contain geologic cross sections; seismic profiles; burial history models; assessments of Carboniferous coalbed methane and Devonian shale gas; distribution information for oil, gas, and coal fields; data on the geochemistry of natural gas and oil; and the fossil-fuel production history of the basin. Although each chapter and subchapter includes references cited, many historical or other important references on Appalachian basin and global fossil-fuel science were omitted because they were not directly applicable to the chapters.

Introduction to the geologic and geophysical studies of Fort Irwin, California: Chapter A in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

USGS Publications Warehouse

Buesch, David C.

2014-01-01

Geologic and geophysical investigations in the vicinity of Fort Irwin National Training Center, California, have been completed in support of groundwater investigations, and are presented in eight chapters of this report. A generalized surficial geologic map along with field and borehole investigations conducted during 2010–11 provide a lithostratigraphic and structural framework for the area during the Cenozoic. Electromagnetic properties of resistivity were measured in the laboratory on hand and core samples, and compared to borehole geophysical resistivity data. These data were used in conjunction with ground-based time-domain and airborne data and interpretations to provide a framework for the shallow lithologic units and structure. Gravity and aeromagnetic maps cover areas ~4 to 5 times that of Fort Irwin. Each chapter includes hydrogeologic applications of the data or model results.

Exploring the "what if?" in geology through a RESTful open-source framework for cloud-based simulation and analysis

NASA Astrophysics Data System (ADS)

Klump, Jens; Robertson, Jess

2016-04-01

The spatial and temporal extent of geological phenomena makes experiments in geology difficult to conduct, if not entirely impossible and collection of data is laborious and expensive - so expensive that most of the time we cannot test a hypothesis. The aim, in many cases, is to gather enough data to build a predictive geological model. Even in a mine, where data are abundant, a model remains incomplete because the information at the level of a blasting block is two orders of magnitude larger than the sample from a drill core, and we have to take measurement errors into account. So, what confidence can we have in a model based on sparse data, uncertainties and measurement error? Our framework consist of two layers: (a) a ground-truth layer that contains geological models, which can be statistically based on historical operations data, and (b) a network of RESTful synthetic sensor microservices which can query the ground-truth for underlying properties and produce a simulated measurement to a control layer, which could be a database or LIMS, a machine learner or a companies' existing data infrastructure. Ground truth data are generated by an implicit geological model which serves as a host for nested models of geological processes as smaller scales. Our two layers are implemented using Flask and Gunicorn, which are open source Python web application framework and server, the PyData stack (numpy, scipy etc) and Rabbit MQ (an open-source queuing library). Sensor data is encoded using a JSON-LD version of the SensorML and Observations and Measurements standards. Containerisation of the synthetic sensors using Docker and CoreOS allows rapid and scalable deployment of large numbers of sensors, as well as sensor discovery to form a self-organized dynamic network of sensors. Real-time simulation of data sources can be used to investigate crucial questions such as the potential information gain from future sensing capabilities, or from new sampling strategies, or the combination of both, and it enables us to test many "what if?" questions, both in geology and in data engineering. What would we be able to see if we could obtain data at higher resolution? How would real-time data analysis change sampling strategies? Does our data infrastructure handle many new real-time data streams? What feature engineering can be deducted for machine learning approaches? By providing a 'data sandbox' able to scale to realistic geological scenarios we hope to start answering some of these questions. Faults happen in real world networks. Future work will investigate the effect of failure on dynamic sensor networks and the impact on the predictive capability of machine learning algorithms.

Documentation for the MODFLOW 6 framework

USGS Publications Warehouse

Hughes, Joseph D.; Langevin, Christian D.; Banta, Edward R.

2017-08-10

MODFLOW is a popular open-source groundwater flow model distributed by the U.S. Geological Survey. Growing interest in surface and groundwater interactions, local refinement with nested and unstructured grids, karst groundwater flow, solute transport, and saltwater intrusion, has led to the development of numerous MODFLOW versions. Often times, there are incompatibilities between these different MODFLOW versions. The report describes a new MODFLOW framework called MODFLOW 6 that is designed to support multiple models and multiple types of models. The framework is written in Fortran using a modular object-oriented design. The primary framework components include the simulation (or main program), Timing Module, Solutions, Models, Exchanges, and Utilities. The first version of the framework focuses on numerical solutions, numerical models, and numerical exchanges. This focus on numerical models allows multiple numerical models to be tightly coupled at the matrix level.

Conceptual modeling framework to support development of site-specific selenium criteria for Lake Koocanusa, Montana, U.S.A., and British Columbia, Canada

USGS Publications Warehouse

Jenni, Karen E.; Naftz, David L.; Presser, Theresa S.

2017-10-16

The U.S. Geological Survey, working with the Montana Department of Environmental Quality and the British Columbia Ministry of the Environment and Climate Change Strategy, has developed a conceptual modeling framework that can be used to provide structured and scientifically based input to the Lake Koocanusa Monitoring and Research Working Group as they consider potential site-specific selenium criteria for Lake Koocanusa, a transboundary reservoir located in Montana and British Columbia. This report describes that modeling framework, provides an example of how it can be applied, and outlines possible next steps for implementing the framework.

U.S. Geological Survey Groundwater Modeling Software: Making Sense of a Complex Natural Resource

USGS Publications Warehouse

Provost, Alden M.; Reilly, Thomas E.; Harbaugh, Arlen W.; Pollock, David W.

2009-01-01

Computer models of groundwater systems simulate the flow of groundwater, including water levels, and the transport of chemical constituents and thermal energy. Groundwater models afford hydrologists a framework on which to organize their knowledge and understanding of groundwater systems, and they provide insights water-resources managers need to plan effectively for future water demands. Building on decades of experience, the U.S. Geological Survey (USGS) continues to lead in the development and application of computer software that allows groundwater models to address scientific and management questions of increasing complexity.

Digital data and geologic map of the Powder Mill Ferry Quadrangle, Shannon and Reynolds counties, Missouri

USGS Publications Warehouse

McDowell, Robert C.; Harrison, Richard W.; Lagueux, Kerry M.

2000-01-01

The geology of the Powder Mill Ferry 7 1/2-minute quadrangle , Shannon and Reynolds Counties, Missouri was mapped from 1997 through 1998 as part of the Midcontinent Karst Systems and Geologic Mapping Project, Eastern Earth Surface Processes Team. The map supports the production of a geologic framework that will be used in hydrogeologic investigations related to potential lead and zinc mining in the Mark Twain National Forest adjacent to the Ozark National Scenic Riverways (National Park Service). Digital geologic coverages will be used by other federal and state agencies in hydrogeologic analyses of the Ozark karst system and in ecological models.

Key subsurface data help to refine Trinity aquifer hydrostratigraphic units, south-central Texas

USGS Publications Warehouse

Blome, Charles D.; Clark, Allan K.

2014-01-01

The geologic framework and hydrologic characteristics of aquifers are important components for studying the nation’s subsurface heterogeneity and predicting its hydraulic budgets. Detailed study of an aquifer’s subsurface hydrostratigraphy is needed to understand both its geologic and hydrologic frameworks. Surface hydrostratigraphic mapping can also help characterize the spatial distribution and hydraulic connectivity of an aquifer’s permeable zones. Advances in three-dimensional (3-D) mapping and modeling have also enabled geoscientists to visualize the spatial relations between the saturated and unsaturated lithologies. This detailed study of two borehole cores, collected in 2001 on the Camp Stanley Storage Activity (CSSA) area, provided the foundation for revising a number of hydrostratigraphic units representing the middle zone of the Trinity aquifer. The CSSA area is a restricted military facility that encompasses approximately 4,000 acres and is located in Boerne, Texas, northwest of the city of San Antonio. Studying both the surface and subsurface geology of the CSSA area are integral parts of a U.S. Geological Survey project funded through the National Cooperative Geologic Mapping Program. This modification of hydrostratigraphic units is being applied to all subsurface data used to construct a proposed 3-D EarthVision model of the CSSA area and areas to the south and west.

Development of a definition, classification system, and model for cultural geology

NASA Astrophysics Data System (ADS)

Mitchell, Lloyd W., III

The concept for this study is based upon a personal interest by the author, an American Indian, in promoting cultural perspectives in undergraduate college teaching and learning environments. Most academicians recognize that merged fields can enhance undergraduate curricula. However, conflict may occur when instructors attempt to merge social science fields such as history or philosophy with geoscience fields such as mining and geomorphology. For example, ideologies of Earth structures derived from scientific methodologies may conflict with historical and spiritual understandings of Earth structures held by American Indians. Specifically, this study addresses the problem of how to combine cultural studies with the geosciences into a new merged academic discipline called cultural geology. This study further attempts to develop the merged field of cultural geology using an approach consisting of three research foci: a definition, a classification system, and a model. Literature reviews were conducted for all three foci. Additionally, to better understand merged fields, a literature review was conducted specifically for academic fields that merged social and physical sciences. Methodologies concentrated on the three research foci: definition, classification system, and model. The definition was derived via a two-step process. The first step, developing keyword hierarchical ranking structures, was followed by creating and analyzing semantic word meaning lists. The classification system was developed by reviewing 102 classification systems and incorporating selected components into a system framework. The cultural geology model was created also utilizing a two-step process. A literature review of scientific models was conducted. Then, the definition and classification system were incorporated into a model felt to reflect the realm of cultural geology. A course syllabus was then developed that incorporated the resulting definition, classification system, and model. This study concludes that cultural geology can be introduced as a merged discipline by using a three-foci framework consisting of a definition, classification system, and model. Additionally, this study reveals that cultural beliefs, attitudes, and behaviors, can be incorporated into a geology course during the curriculum development process, using an approach known as 'learner-centered'. This study further concludes that cultural beliefs, derived from class members, are an important source of curriculum materials.

Relations between well-field pumping and induced canal leakage in east-central Miami-Dade County, Florida, 2010-2011

USGS Publications Warehouse

Nemec, Katherine; Antolino, Dominick J.; Turtora, Michael; Adam Foster,

2015-08-26

Results from the groundwater model and the stable isotope data analysis indicate the importance of considering geologic heterogeneity when investigating the relations between pumping and canal leakage, not only at this site, but also at other sites with similar heterogeneous geology. The model results were consistently sensitive to the hydrogeologic framework and changes in hydraulic conductivities. The model and the isotope data indicate that the majority of the groundwater/surface-water interactions occurred within the shallow flow zone. A relatively lower-permeability geologic layer occurring between the shallowest and deep preferential flow zones lessens the interactions between the production wells and the canal.

Three-dimensional hydrogeologic framework model of the Rio Grande transboundary region of New Mexico and Texas, USA, and northern Chihuahua, Mexico

USGS Publications Warehouse

Sweetkind, Donald S.

2017-09-08

As part of a U.S. Geological Survey study in cooperation with the Bureau of Reclamation, a digital three-dimensional hydrogeologic framework model was constructed for the Rio Grande transboundary region of New Mexico and Texas, USA, and northern Chihuahua, Mexico. This model was constructed to define the aquifer system geometry and subsurface lithologic characteristics and distribution for use in a regional numerical hydrologic model. The model includes five hydrostratigraphic units: river channel alluvium, three informal subdivisions of Santa Fe Group basin fill, and an undivided pre-Santa Fe Group bedrock unit. Model input data were compiled from published cross sections, well data, structure contour maps, selected geophysical data, and contiguous compilations of surficial geology and structural features in the study area. These data were used to construct faulted surfaces that represent the upper and lower subsurface hydrostratigraphic unit boundaries. The digital three-dimensional hydrogeologic framework model is constructed through combining faults, the elevation of the tops of each hydrostratigraphic unit, and boundary lines depicting the subsurface extent of each hydrostratigraphic unit. The framework also compiles a digital representation of the distribution of sedimentary facies within each hydrostratigraphic unit. The digital three-dimensional hydrogeologic model reproduces with reasonable accuracy the previously published subsurface hydrogeologic conceptualization of the aquifer system and represents the large-scale geometry of the subsurface aquifers. The model is at a scale and resolution appropriate for use as the foundation for a numerical hydrologic model of the study area.

Modeling uncertainty in producing natural gas from tight sands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chermak, J.M.; Dahl, C.A.; Patrick, R.H

1995-12-31

Since accurate geologic, petroleum engineering, and economic information are essential ingredients in making profitable production decisions for natural gas, we combine these ingredients in a dynamic framework to model natural gas reservoir production decisions. We begin with the certainty case before proceeding to consider how uncertainty might be incorporated in the decision process. Our production model uses dynamic optimal control to combine economic information with geological constraints to develop optimal production decisions. To incorporate uncertainty into the model, we develop probability distributions on geologic properties for the population of tight gas sand wells and perform a Monte Carlo study tomore » select a sample of wells. Geological production factors, completion factors, and financial information are combined into the hybrid economic-petroleum reservoir engineering model to determine the optimal production profile, initial gas stock, and net present value (NPV) for an individual well. To model the probability of the production abandonment decision, the NPV data is converted to a binary dependent variable. A logit model is used to model this decision as a function of the above geological and economic data to give probability relationships. Additional ways to incorporate uncertainty into the decision process include confidence intervals and utility theory.« less

Kinematic Structural Modelling in Bayesian Networks

NASA Astrophysics Data System (ADS)

Schaaf, Alexander; de la Varga, Miguel; Florian Wellmann, J.

2017-04-01

We commonly capture our knowledge about the spatial distribution of distinct geological lithologies in the form of 3-D geological models. Several methods exist to create these models, each with its own strengths and limitations. We present here an approach to combine the functionalities of two modeling approaches - implicit interpolation and kinematic modelling methods - into one framework, while explicitly considering parameter uncertainties and thus model uncertainty. In recent work, we proposed an approach to implement implicit modelling algorithms into Bayesian networks. This was done to address the issues of input data uncertainty and integration of geological information from varying sources in the form of geological likelihood functions. However, one general shortcoming of implicit methods is that they usually do not take any physical constraints into consideration, which can result in unrealistic model outcomes and artifacts. On the other hand, kinematic structural modelling intends to reconstruct the history of a geological system based on physically driven kinematic events. This type of modelling incorporates simplified, physical laws into the model, at the cost of a substantial increment of usable uncertain parameters. In the work presented here, we show an integration of these two different modelling methodologies, taking advantage of the strengths of both of them. First, we treat the two types of models separately, capturing the information contained in the kinematic models and their specific parameters in the form of likelihood functions, in order to use them in the implicit modelling scheme. We then go further and combine the two modelling approaches into one single Bayesian network. This enables the direct flow of information between the parameters of the kinematic modelling step and the implicit modelling step and links the exclusive input data and likelihoods of the two different modelling algorithms into one probabilistic inference framework. In addition, we use the capabilities of Noddy to analyze the topology of structural models to demonstrate how topological information, such as the connectivity of two layers across an unconformity, can be used as a likelihood function. In an application to a synthetic case study, we show that our approach leads to a successful combination of the two different modelling concepts. Specifically, we show that we derive ensemble realizations of implicit models that now incorporate the knowledge of the kinematic aspects, representing an important step forward in the integration of knowledge and a corresponding estimation of uncertainties in structural geological models.

A universal surface complexation framework for modeling proton binding onto bacterial surfaces in geologic settings

USGS Publications Warehouse

Borrok, D.; Turner, B.F.; Fein, J.B.

2005-01-01

Adsorption onto bacterial cell walls can significantly affect the speciation and mobility of aqueous metal cations in many geologic settings. However, a unified thermodynamic framework for describing bacterial adsorption reactions does not exist. This problem originates from the numerous approaches that have been chosen for modeling bacterial surface protonation reactions. In this study, we compile all currently available potentiometric titration datasets for individual bacterial species, bacterial consortia, and bacterial cell wall components. Using a consistent, four discrete site, non-electrostatic surface complexation model, we determine total functional group site densities for all suitable datasets, and present an averaged set of 'universal' thermodynamic proton binding and site density parameters for modeling bacterial adsorption reactions in geologic systems. Modeling results demonstrate that the total concentrations of proton-active functional group sites for the 36 bacterial species and consortia tested are remarkably similar, averaging 3.2 ?? 1.0 (1??) ?? 10-4 moles/wet gram. Examination of the uncertainties involved in the development of proton-binding modeling parameters suggests that ignoring factors such as bacterial species, ionic strength, temperature, and growth conditions introduces relatively small error compared to the unavoidable uncertainty associated with the determination of cell abundances in realistic geologic systems. Hence, we propose that reasonable estimates of the extent of bacterial cell wall deprotonation can be made using averaged thermodynamic modeling parameters from all of the experiments that are considered in this study, regardless of bacterial species used, ionic strength, temperature, or growth condition of the experiment. The average site densities for the four discrete sites are 1.1 ?? 0.7 ?? 10-4, 9.1 ?? 3.8 ?? 10-5, 5.3 ?? 2.1 ?? 10-5, and 6.6 ?? 3.0 ?? 10-5 moles/wet gram bacteria for the sites with pKa values of 3.1, 4.7, 6.6, and 9.0, respectively. It is our hope that this thermodynamic framework for modeling bacteria-proton binding reactions will also provide the basis for the development of an internally consistent set of bacteria-metal binding constants. 'Universal' constants for bacteria-metal binding reactions can then be used in conjunction with equilibrium constants for other important metal adsorption and complexation reactions to calculate the overall distribution of metals in realistic geologic systems.

A machine learning approach to the potential-field method for implicit modeling of geological structures

NASA Astrophysics Data System (ADS)

Gonçalves, Ítalo Gomes; Kumaira, Sissa; Guadagnin, Felipe

2017-06-01

Implicit modeling has experienced a rise in popularity over the last decade due to its advantages in terms of speed and reproducibility in comparison with manual digitization of geological structures. The potential-field method consists in interpolating a scalar function that indicates to which side of a geological boundary a given point belongs to, based on cokriging of point data and structural orientations. This work proposes a vector potential-field solution from a machine learning perspective, recasting the problem as multi-class classification, which alleviates some of the original method's assumptions. The potentials related to each geological class are interpreted in a compositional data framework. Variogram modeling is avoided through the use of maximum likelihood to train the model, and an uncertainty measure is introduced. The methodology was applied to the modeling of a sample dataset provided with the software Move™. The calculations were implemented in the R language and 3D visualizations were prepared with the rgl package.

Soil and geologic controls on recharge and groundwater flow response to climate perturbation: A case study of the Yakima River Basin

NASA Astrophysics Data System (ADS)

Nguyen, T. T.; Pham, H. V.; Bachmann, M.; Tague, C.; Adam, J. C.

2017-12-01

The Yakima River Basin (YRB) is one of the most important agricultural basins in Washington State with annual revenues in excess of $3.2 billion. This intensively irrigated basin is, however, one of the state's most climatically sensitive water resources system as it heavily relies on winter snowpack and limited reservoir storage. Water shortages and drought are expected to be more frequent with climate change, population growth and increasing agricultural demand. This could result in significant impacts on the groundwater system and subsequently the Yakima River. The goal of this study is to assess how soil and geologic characteristics affect catchment recharge and groundwater flow across three catchments within the YRB using a coupled framework including a physically based hydro-ecological model, the Regional Hydro-Ecologic Simulation System (RHESSys) and a groundwater model, MODFLOW. Soil and geologic-related parameters were randomly sampled to use within the Distributed Evaluation of Local Sensitivity Analysis (DELSA) framework to explore their roles in governing catchment recharge and groundwater flow to climate perturbation. Preliminarily results show that catchment recharge is most sensitive to variation in soil transmissivity in two catchments. However, in the other catchment, recharge is more influenced by soil field capacity and bypass recharge. Recharge is also more sensitive to geologic related parameters in catchments where a portion of its flow comes from deep groundwater. When including the effect of climate perturbations, the sensitivity of recharge responses to soil and geologic characteristics varies with temperature and precipitation change. On the other hand, horizontal hydraulic conductivity is the dominant factor that controls groundwater flow responses in catchments with low permeability soil; alternatively, specific storage (and, to some extent, vertical anisotropy) are important in catchments with more conductive soil. The modeling framework developed in this study will be used to investigate the impacts of both climate and drought-relief supplemental pumping on potential recharge, groundwater and streamflow changes in the YRB.

Geo3DML: A standard-based exchange format for 3D geological models

NASA Astrophysics Data System (ADS)

Wang, Zhangang; Qu, Honggang; Wu, Zixing; Wang, Xianghong

2018-01-01

A geological model (geomodel) in three-dimensional (3D) space is a digital representation of the Earth's subsurface, recognized by geologists and stored in resultant geological data (geodata). The increasing demand for data management and interoperable applications of geomodelscan be addressed by developing standard-based exchange formats for the representation of not only a single geological object, but also holistic geomodels. However, current standards such as GeoSciML cannot incorporate all the geomodel-related information. This paper presents Geo3DML for the exchange of 3D geomodels based on the existing Open Geospatial Consortium (OGC) standards. Geo3DML is based on a unified and formal representation of structural models, attribute models and hierarchical structures of interpreted resultant geodata in different dimensional views, including drills, cross-sections/geomaps and 3D models, which is compatible with the conceptual model of GeoSciML. Geo3DML aims to encode all geomodel-related information integrally in one framework, including the semantic and geometric information of geoobjects and their relationships, as well as visual information. At present, Geo3DML and some supporting tools have been released as a data-exchange standard by the China Geological Survey (CGS).

Preliminary geologic framework developed for a proposed environmental monitoring study of a deep, unconventional Marcellus Shale drill site, Washington County, Pennsylvania

USGS Publications Warehouse

Stamm, Robert G.

2018-06-08

BackgroundIn the fall of 2011, the U.S. Geological Survey (USGS) was afforded an opportunity to participate in an environmental monitoring study of the potential impacts of a deep, unconventional Marcellus Shale hydraulic fracturing site. The drill site of the prospective case study is the “Range Resources MCC Partners L.P. Units 1-5H” location (also referred to as the “RR–MCC” drill site), located in Washington County, southwestern Pennsylvania. Specifically, the USGS was approached to provide a geologic framework that would (1) provide geologic parameters for the proposed area of a localized groundwater circulation model, and (2) provide potential information for the siting of both shallow and deep groundwater monitoring wells located near the drill pad and the deviated drill legs.The lead organization of the prospective case study of the RR–MCC drill site was the Groundwater and Ecosystems Restoration Division (GWERD) of the U.S. Environmental Protection Agency. Aside from the USGS, additional partners/participants were to include the Department of Energy, the Pennsylvania Geological Survey, the Pennsylvania Department of Environmental Protection, and the developer Range Resources LLC. During the initial cooperative phase, GWERD, with input from the participating agencies, drafted a Quality Assurance Project Plan (QAPP) that proposed much of the objectives, tasks, sampling and analytical procedures, and documentation of results.Later in 2012, the proposed cooperative agreement between the aforementioned partners and the associated land owners for a monitoring program at the drill site was not executed. Therefore, the prospective case study of the RR–MCC site was terminated and no installation of groundwater monitoring wells nor the collection of nearby soil, stream sediment, and surface-water samples were made.Prior to the completion of the QAPP and termination of the perspective case study the geologic framework was rapidly conducted and nearly completed. This was done for three principal reasons. First, there was an immediate need to know the distribution of the relatively undisturbed surface to near-surface bedrock geology and unconsolidated materials for the collection of baseline surface data prior to drill site development (drill pad access road, drill pad leveling) and later during monitoring associated with well drilling, well development, and well production. Second, it was necessary to know the bedrock geology to support the siting of: (1) multiple shallow groundwater monitoring wells (possibly as many as four) surrounding and located immediately adjacent to the drill pad, and (2) deep groundwater monitoring wells (possibly two) located at distance from the drill pad with one possibly being sited along one of the deviated production drill legs. Lastly, the framework geology would provide the lateral extent, thickness, lithology, and expected discontinuities of geologic units (to be parsed or grouped as hydrostratigraphic units) and regional structure trends as inputs into the groundwater model.This report provides the methodology of geologic data accumulation and aggregation, and its integration into a geographic information system (GIS) based program. The GIS program will allow multiple data to be exported in various formats (shapefiles [.shp], database files [.dbf], and Keyhole Markup Language files [.KML]) for use in surface and subsurface geologic site characterization, for sampling strategies, and for inputs for groundwater modeling.

3D Geological Model for "LUSI" - a Deep Geothermal System

NASA Astrophysics Data System (ADS)

Sohrabi, Reza; Jansen, Gunnar; Mazzini, Adriano; Galvan, Boris; Miller, Stephen A.

2016-04-01

Geothermal applications require the correct simulation of flow and heat transport processes in porous media, and many of these media, like deep volcanic hydrothermal systems, host a certain degree of fracturing. This work aims to understand the heat and fluid transport within a new-born sedimentary hosted geothermal system, termed Lusi, that began erupting in 2006 in East Java, Indonesia. Our goal is to develop conceptual and numerical models capable of simulating multiphase flow within large-scale fractured reservoirs such as the Lusi region, with fractures of arbitrary size, orientation and shape. Additionally, these models can also address a number of other applications, including Enhanced Geothermal Systems (EGS), CO2 sequestration (Carbon Capture and Storage CCS), and nuclear waste isolation. Fractured systems are ubiquitous, with a wide-range of lengths and scales, making difficult the development of a general model that can easily handle this complexity. We are developing a flexible continuum approach with an efficient, accurate numerical simulator based on an appropriate 3D geological model representing the structure of the deep geothermal reservoir. Using previous studies, borehole information and seismic data obtained in the framework of the Lusi Lab project (ERC grant n°308126), we present here the first 3D geological model of Lusi. This model is calculated using implicit 3D potential field or multi-potential fields, depending on the geological context and complexity. This method is based on geological pile containing the geological history of the area and relationship between geological bodies allowing automatic computation of intersections and volume reconstruction. Based on the 3D geological model, we developed a new mesh algorithm to create hexahedral octree meshes to transfer the structural geological information for 3D numerical simulations to quantify Thermal-Hydraulic-Mechanical-Chemical (THMC) physical processes.

Learn More

EPA Pesticide Factsheets

NHDPlus is a geospatial, hydrologic framework dataset that is intended for use by geospatial analysts and modelers to support water resources related applications. NHDPlus was developed by the USEPA in partnership with the US Geologic Survey

Get Data

EPA Pesticide Factsheets

NHDPlus is a geospatial, hydrologic framework dataset that is intended for use by geospatial analysts and modelers to support water resources related applications. NHDPlus was developed by the USEPA in partnership with the US Geologic Survey

Basic Information

EPA Pesticide Factsheets

NHDPlus is a geospatial, hydrologic framework dataset that is intended for use by geospatial analysts and modelers to support water resources related applications. NHDPlus was developed by the USEPA in partnership with the US Geologic Survey

Geologic map of the Callville Bay Quadrangle, Clark County, Nevada, and Mohave County, Arizona

USGS Publications Warehouse

Anderson, R. Ernest

2003-01-01

Report: 139 Map Scale: 1:24,000 Map Type: colored geologic map A 1:24,000-scale, full-color geologic map and four cross sections of the Callville Bay 7-minute quadrangle in Clark County, Nevada and Mohave County, Arizona. An accompanying text describes 21 stratigraphic units of Paleozoic and Mesozoic sedimentary rocks and 40 units of Cenozoic sedimentary, volcanic, and intrusive rocks. It also discusses the structural setting, framework, and history of the quadrangle and presents a model for its tectonic development.

Geologic framework for the national assessment of carbon dioxide storage resources: Permian and Palo Duro Basins and Bend Arch-Fort Worth Basin: Chapter K in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Merrill, Matthew D.; Slucher, Ernie R.; Roberts-Ashby, Tina L.; Warwick, Peter D.; Blondes, Madalyn S.; Freeman, P.A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2015-01-01

The U.S. Geological Survey has completed an assessment of the potential geologic carbon dioxide storage resource in the onshore areas of the United States. To provide geological context and input data sources for the resources numbers, framework documents are being prepared for all areas that were investigated as part of the national assessment. This report is the geologic framework document for the Permian and Palo Duro Basins, the combined Bend arch-Fort Worth Basin area, and subbasins therein of Texas, New Mexico, and Oklahoma. In addition to a summarization of the geology and petroleum resources of studied basins, the individual storage assessment units (SAUs) within the basins are described and explanations for their selection are presented. Though appendixes in the national assessment publications include the input values used to calculate the available storage resource, this framework document provides only the context and source of inputs selected by the assessment geologists. Spatial files of boundaries for the SAUs herein, as well as maps of the density of known well bores that penetrate the SAU seal, are available for download with the release of this report.

Geologic framework for the national assessment of carbon dioxide storage resources—Southern Rocky Mountain Basins: Chapter M in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Merrill, Matthew D.; Drake, Ronald M.; Buursink, Marc L.; Craddock, William H.; East, Joseph A.; Slucher, Ernie R.; Warwick, Peter D.; Brennan, Sean T.; Blondes, Madalyn S.; Freeman, Philip A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2016-06-02

The U.S. Geological Survey has completed an assessment of the potential geologic carbon dioxide storage resources in the onshore areas of the United States. To provide geological context and input data sources for the resources numbers, framework documents are being prepared for all areas that were investigated as part of the national assessment. This report, chapter M, is the geologic framework document for the Uinta and Piceance, San Juan, Paradox, Raton, Eastern Great, and Black Mesa Basins, and subbasins therein of Arizona, Colorado, Idaho, Nevada, New Mexico, and Utah. In addition to a summary of the geology and petroleum resources of studied basins, the individual storage assessment units (SAUs) within the basins are described and explanations for their selection are presented. Although appendixes in the national assessment publications include the input values used to calculate the available storage resource, this framework document provides only the context and source of the input values selected by the assessment geologists. Spatial-data files of the boundaries for the SAUs, and the well-penetration density of known well bores that penetrate the SAU seal, are available for download with the release of this report.

Modeling and Crustal Structure in the Future Reservoir of Jequitaí, Brazil

NASA Astrophysics Data System (ADS)

Teixeira, C. D.; Von Huelsen, M. G.; Chemale, F., Jr.; Nascimento, A. V. D. S., Sr.; do Sacramento, V., Sr.; Garcia, V. B. P., Sr.

2017-12-01

Integrated geophysical and geological data analysis in the state of Minas Gerais, Brazil, allowed the modeling of the subsurface framework in a region where a reservoir - the Jequitaí reservoir - will be constructed. Studies of this nature during the previous stages of the construction of large hydroelectric projects are highly important, because the regional geology understanding associated with geophysical data interpretation can help to prevent damage in the physical structure of the dam, which will aid in its preservation. The use of gravity and magnetic data in a 2D crustal model provided information on a possible framework of the area and revealed features not mapped until now, which may be useful for further studies and can contribute to the understanding of this portion of the crust. The results show the presence of high gravity anomalies in the southern part of the study area, besides extensive lineaments that cross the whole area, interpreted as possible faults and dykes. Depth estimation techniques, such as Euler deconvolution and radially averaged power spectrum, allowed the identification of continuous structures up to 400 m depth, and showed differences in the basement depth in the northern and southern portions of the study area. Inversion of the gravity data along a profile crossing a gravity anomaly yielded to information about the depth, thickness and shape of a possible intrusive body. The geological-geophysical model was consistent with the interpretations based on surface geology and in the gravity and magnetic signal, because the section could be modeled respecting the geophysical data and the pre-existing structural proposals.

Screening and ranking framework (SRF) for geologic CO2 storagesite selection on the basis of HSE risk

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oldenburg, Curtis M.

2006-11-27

A screening and ranking framework (SRF) has been developedto evaluate potential geologic carbon dioxide (CO2) storage sites on thebasis of health, safety, and environmental (HSE) risk arising from CO2leakage. The approach is based on the assumption that CO2 leakage risk isdependent on three basic characteristics of a geologic CO2 storage site:(1) the potential for primary containment by the target formation; (2)the potential for secondary containment if the primary formation leaks;and (3) the potential for attenuation and dispersion of leaking CO2 ifthe primary formation leaks and secondary containment fails. Theframework is implemented in a spreadsheet in which users enter numericalscores representingmore » expert opinions or published information along withestimates of uncertainty. Applications to three sites in Californiademonstrate the approach. Refinements and extensions are possible throughthe use of more detailed data or model results in place of propertyproxies.« less

NHDPlus (National Hydrography Dataset Plus)

EPA Pesticide Factsheets

NHDPlus is a geospatial, hydrologic framework dataset that is intended for use by geospatial analysts and modelers to support water resources related applications. NHDPlus was developed by the USEPA in partnership with the US Geologic Survey

Incorporating geologic information into hydraulic tomography: A general framework based on geostatistical approach

NASA Astrophysics Data System (ADS)

Zha, Yuanyuan; Yeh, Tian-Chyi J.; Illman, Walter A.; Onoe, Hironori; Mok, Chin Man W.; Wen, Jet-Chau; Huang, Shao-Yang; Wang, Wenke

2017-04-01

Hydraulic tomography (HT) has become a mature aquifer test technology over the last two decades. It collects nonredundant information of aquifer heterogeneity by sequentially stressing the aquifer at different wells and collecting aquifer responses at other wells during each stress. The collected information is then interpreted by inverse models. Among these models, the geostatistical approaches, built upon the Bayesian framework, first conceptualize hydraulic properties to be estimated as random fields, which are characterized by means and covariance functions. They then use the spatial statistics as prior information with the aquifer response data to estimate the spatial distribution of the hydraulic properties at a site. Since the spatial statistics describe the generic spatial structures of the geologic media at the site rather than site-specific ones (e.g., known spatial distributions of facies, faults, or paleochannels), the estimates are often not optimal. To improve the estimates, we introduce a general statistical framework, which allows the inclusion of site-specific spatial patterns of geologic features. Subsequently, we test this approach with synthetic numerical experiments. Results show that this approach, using conditional mean and covariance that reflect site-specific large-scale geologic features, indeed improves the HT estimates. Afterward, this approach is applied to HT surveys at a kilometer-scale-fractured granite field site with a distinct fault zone. We find that by including fault information from outcrops and boreholes for HT analysis, the estimated hydraulic properties are improved. The improved estimates subsequently lead to better prediction of flow during a different pumping test at the site.

D Geological Framework Models as a Teaching Aid for Geoscience

NASA Astrophysics Data System (ADS)

Kessler, H.; Ward, E.; Geological ModelsTeaching Project Team

2010-12-01

3D geological models have great potential as a resource for universities when teaching foundation geological concepts as it allows the student to visualise and interrogate UK geology. They are especially useful when dealing with the conversion of 2D field, map and GIS outputs into three dimensional geological units, which is a common problem for all students of geology. Today’s earth science students use a variety of skills and processes during their learning experience including the application of schema’s, spatial thinking, image construction, detecting patterns, memorising figures, mental manipulation and interpretation, making predictions and deducing the orientation of themselves and the rocks. 3D geological models can reinforce spatial thinking strategies and encourage students to think about processes and properties, in turn helping the student to recognise pre-learnt geological principles in the field and to convert what they see at the surface into a picture of what is going on at depth. Learning issues faced by students may also be encountered by experts, policy managers, and stakeholders when dealing with environmental problems. Therefore educational research of student learning in earth science may also improve environmental decision making. 3D geological framework models enhance the learning of Geosciences because they: ● enable a student to observe, manipulate and interpret geology; in particular the models instantly convert two-dimensional geology (maps, boreholes and cross-sections) into three dimensions which is a notoriously difficult geospatial skill to acquire. ● can be orientated to whatever the user finds comfortable and most aids recognition and interpretation. ● can be used either to teach geosciences to complete beginners or add to experienced students body of knowledge (whatever point that may be at). Models could therefore be packaged as a complete educational journey or students and tutor can select certain areas of the model or educational material to incorporate it into an existing area of the syllabus such as a field trip, project work or a certain taxing geological concept such as dip and strike. ● can easily be utilised by students unable to attend university conventionally (illness or disability), distance learning students or for extra curricular activities and continuing professional development courses. ● can be used repeatedly and in such a way as to continually build on geoscience aspects - this practice will improve the student’s geospatial skills. ● can be compared with that seen directly in the field which aids the student in recognising particular patterns or sequences. It also demonstrates how different and complex geology looks in the field and thus how important it is not to rely on models alone. ● are interactive and the accompanying educational material is engaging, dealing with authentic, contemporary scientific problems meaning the student will have to ask questions, think critically and solve problems. ● can often be more practical and better financial alternatives to some teaching methods currently employed. ● incorporate strategies where students first explore, are then introduced to terminology and concepts, finally students apply their knowledge to different, but related problems. This can be further reinforced and explored with fellow students.

Three-dimensional geologic framework modeling of faulted hydrostratigraphic units within the Edwards Aquifer, Northern Bexar County, Texas

USGS Publications Warehouse

Pantea, Michael P.; Cole, James C.

2004-01-01

This report describes a digital, three-dimensional faulted hydrostratigraphic model constructed to represent the geologic framework of the Edwards aquifer system in the area of San Antonio, northern Bexar County, Texas. The model is based on mapped geologic relationships that reflect the complex structures of the Balcones fault zone, detailed lithologic descriptions and interpretations of about 40 principal wells (and qualified data from numerous other wells), and a conceptual model of the gross geometry of the Edwards Group units derived from prior interpretations of depositional environments and paleogeography. The digital model depicts the complicated intersections of numerous major and minor faults in the subsurface, as well as their individual and collective impacts on the continuity of the aquifer-forming units of the Edwards Group and the Georgetown Formation. The model allows for detailed examination of the extent of fault dislocation from place to place, and thus the extent to which the effective cross-sectional area of the aquifer is reduced by faulting. The model also depicts the internal hydrostratigraphic subdivisions of the Edwards aquifer, consisting of three major and eight subsidiary hydrogeologic units. This geologic framework model is useful for visualizing the geologic structures within the Balcones fault zone and the interactions of en-echelon fault strands and flexed connecting fault-relay ramps. The model also aids in visualizing the lateral connections between hydrostratigraphic units of relatively high and low permeability across the fault strands. Introduction The Edwards aquifer is the principal source of water for municipal, agricultural, industrial, and military uses by nearly 1.5 million inhabitants of the greater San Antonio, Texas, region (Hovorka and others, 1996; Sharp and Banner, 1997). Discharges from the Edwards aquifer also support local recreation and tourism industries at Barton, Comal, and San Marcos Springs located northeast of San Antonio (Barker and others, 1994), as well as base flow for agricultural applications farther downstream. Average annual discharge from large springs (Comal, San Marcos, Hueco, and others) from the Edwards aquifer was about 365,000 acre-ft from 1934 to1998, with sizeable fluctuations related to annual variations in rainfall. Withdrawals through pumping have increased steadily from about 250,000 acre-ft during the 1960s to over 400,000 acre-ft in the 1990s in response to population growth, especially in the San Antonio metropolitan area (Slattery and Brown, 1999). Average annual recharge to the system (determined through stream gaging) has also varied considerably with annual rainfall fluctuations, but has been about 635,000 acre-ft over the last several decades.

Subsurface geological modeling using GIS and remote sensing data: a case study from Platanos landslide, Western Greece

NASA Astrophysics Data System (ADS)

Kavoura, K.; Kordouli, M.; Nikolakopoulos, K.; Elias, P.; Sykioti, O.; Tsagaris, V.; Drakatos, G.; Rondoyanni, Th.; Tsiambaos, G.; Sabatakakis, N.; Anastasopoulos, V.

2014-08-01

Landslide phenomena constitute a major geological hazard in Greece and especially in the western part of the country as a result of anthropogenic activities, growing urbanization and uncontrolled land - use. More frequent triggering events and increased susceptibility of the ground surface to instabilities as consequence of climate change impacts (continued deforestation mainly due to the devastating forest wildfires and extreme meteorological events) have also increased the landslide risk. The studied landslide occurrence named "Platanos" has been selected within the framework of "Landslide Vulnerability Model - LAVMO" project that aims at creating a persistently updated electronic platform assessing risks related with landslides. It is a coastal area situated between Korinthos and Patras at the northwestern part of the elongated graben of the Corinth Gulf. The paper presents the combined use of geological-geotechnical insitu data, remote sensing data and GIS techniques for the evaluation of a subsurface geological model. High accuracy Digital Surface Model (DSM), airphotos mosaic and satellite data, with a spatial resolution of 0.5m were used for an othophoto base map compilation of the study area. Geological - geotechnical data obtained from exploratory boreholes were digitized and implemented in a GIS platform with engineering geological maps for a three - dimensional subsurface model evaluation. This model is provided for being combined with inclinometer measurements for sliding surface location through the instability zone.

Geologic Cross Section D-D' Through the Appalachian Basin from the Findlay Arch, Sandusky County, Ohio, to the Valley and Ridge Province, Hardy County, West Virginia

USGS Publications Warehouse

Ryder, Robert T.; Crangle, Robert D.; Trippi, Michael H.; Swezey, Christopher S.; Lentz, Erika E.; Rowan, Elisabeth L.; Hope, Rebecca S.

2009-01-01

Geologic cross section D-D' is the second in a series of cross sections constructed by the U.S. Geological Survey to document and improve understanding of the geologic framework and petroleum systems of the Appalachian basin. Cross section D-D' provides a regional view of the structural and stratigraphic framework of the Appalachian basin from the Findlay arch in northwestern Ohio to the Valley and Ridge province in eastern West Virginia, a distance of approximately 290 miles. The information shown on the cross section is based on geological and geophysical data from 13 deep drill holes, several of which penetrate the Paleozoic sedimentary rocks of the basin and bottom in Mesoproterozoic (Grenville-age) crystalline basement rocks. This cross section is a companion to cross section E-E' (Ryder and others, 2008) that is located about 25 to 50 mi to the southwest. Although specific petroleum systems in the Appalachian basin are not identified on the cross section, many of their key elements (such as source rocks, reservoir rocks, seals, and traps) can be inferred from lithologic units, unconformities, and geologic structures shown on the cross section. Other aspects of petroleum systems (such as the timing of petroleum generation and preferred migration pathways) may be evaluated by burial history, thermal history, and fluid flow models based on information shown on the cross section. Cross section D-D' lacks the detail to illustrate key elements of coal systems (such as paleoclimate, coal quality, and coal rank), but it does provide a general geologic framework (stratigraphic units and general rock types) for the coal-bearing section. Also, cross section D-D' may be used as a reconnaissance tool to identify plausible geologic structures and strata for the subsurface storage of liquid waste or for the sequestration of carbon dioxide.

Reservoir Modeling by Data Integration via Intermediate Spaces and Artificial Intelligence Tools in MPS Simulation Frameworks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ahmadi, Rouhollah, E-mail: rouhollahahmadi@yahoo.com; Khamehchi, Ehsan

Conditioning stochastic simulations are very important in many geostatistical applications that call for the introduction of nonlinear and multiple-point data in reservoir modeling. Here, a new methodology is proposed for the incorporation of different data types into multiple-point statistics (MPS) simulation frameworks. Unlike the previous techniques that call for an approximate forward model (filter) for integration of secondary data into geologically constructed models, the proposed approach develops an intermediate space where all the primary and secondary data are easily mapped onto. Definition of the intermediate space, as may be achieved via application of artificial intelligence tools like neural networks andmore » fuzzy inference systems, eliminates the need for using filters as in previous techniques. The applicability of the proposed approach in conditioning MPS simulations to static and geologic data is verified by modeling a real example of discrete fracture networks using conventional well-log data. The training patterns are well reproduced in the realizations, while the model is also consistent with the map of secondary data.« less

Geologic cross section C-C' through the Appalachian basin from Erie County, north-central Ohio, to the Valley and Ridge province, Bedford County, south-central Pennsylvania

USGS Publications Warehouse

Ryder, Robert T.; Trippi, Michael H.; Swezey, Christopher S.; Crangle, Robert D.; Hope, Rebecca S.; Rowan, Elisabeth L.; Lentz, Erika E.

2012-01-01

Geologic cross section C-C' is the third in a series of cross sections constructed by the U.S. Geological Survey (USGS) to document and improve understanding of the geologic framework and petroleum systems of the Appalachian basin. Cross section C-C' provides a regional view of the structural and stratigraphic framework of the Appalachian basin from north-central Ohio to the Valley and Ridge province in south-central Pennsylvania, a distance of approximately 260 miles (mi). This cross section is a companion to cross sections E-E' and D-D' that are located about 50 to 125 mi and 25 to 50 mi, respectively, to the southwest. Cross section C-C' contains much information that is useful for evaluating energy resources in the Appalachian basin. Although specific petroleum systems are not identified on the cross section, many of their key elements (such as source rocks, reservoir rocks, seals, and traps) can be inferred from lithologic units, unconformities, and geologic structures shown on the cross section. Other aspects of petroleum systems (such as the timing of petroleum generation and preferred migration pathways) may be evaluated by burial history, thermal history, and fluid flow models based on what is shown on the cross section. Cross section C-C' also provides a general framework (stratigraphic units and general rock types) for the coal-bearing section, although the cross section lacks the detail to illustrate key elements of coal systems (such as paleoclimate, coal quality, and coal rank). In addition, cross section C-C' may be used as a reconnaissance tool to identify plausible geologic structures and strata for the subsurface storage of liquid waste or for the sequestration of carbon dioxide.

Surface and subsurface geologic risk factors to ground water affecting brownfield redevelopment potential.

PubMed

Kaufman, Martin M; Murray, Kent S; Rogers, Daniel T

2003-01-01

A model is created for assessing the redevelopment potential of brownfields. The model is derived from a space and time conceptual framework that identifies and measures the surface and subsurface risk factors present at brownfield sites. The model then combines these factors with a contamination extent multiplier at each site to create an index of redevelopment potential. Results from the application of the model within an urbanized watershed demonstrate clear differences between the redevelopment potential present within five different near-surface geologic units, with those units containing clay being less vulnerable to subsurface contamination. With and without the extent multiplier, the total risk present at the brownfield sites within all the geologic units is also strongly correlated to the actual costs of remediation. Thus, computing the total surface and subsurface risk within a watershed can help guide the remediation efforts at broad geographic scales, and prioritize the locations for redevelopment.

Heat-pipe Earth.

PubMed

Moore, William B; Webb, A Alexander G

2013-09-26

The heat transport and lithospheric dynamics of early Earth are currently explained by plate tectonic and vertical tectonic models, but these do not offer a global synthesis consistent with the geologic record. Here we use numerical simulations and comparison with the geologic record to explore a heat-pipe model in which volcanism dominates surface heat transport. These simulations indicate that a cold and thick lithosphere developed as a result of frequent volcanic eruptions that advected surface materials downwards. Declining heat sources over time led to an abrupt transition to plate tectonics. Consistent with model predictions, the geologic record shows rapid volcanic resurfacing, contractional deformation, a low geothermal gradient across the bulk of the lithosphere and a rapid decrease in heat-pipe volcanism after initiation of plate tectonics. The heat-pipe Earth model therefore offers a coherent geodynamic framework in which to explore the evolution of our planet before the onset of plate tectonics.

A refined characterization of the alluvial geology of yucca flat and its effect on bulk hydraulic conductivity

USGS Publications Warehouse

Phelps, G.A.; Halford, K.J.

2011-01-01

In Yucca Flat, on the Nevada National Security Site in southern Nevada, the migration of radionuclides from tests located in the alluvial deposits into the Paleozoic carbonate aquifer involves passage through a thick, heterogeneous section of late Tertiary and Quaternary alluvial sediments. An understanding of the lateral and vertical changes in the material properties of the alluvial sediments will aid in the further development of the hydrogeologic framework and the delineation of hydrostratigraphic units and hydraulic properties required for simulating groundwater flow in the Yucca Flat area. Previously published geologic models for the alluvial sediments within Yucca Flat are based on extensive examination and categorization of drill-hole data, combined with a simple, data-driven interpolation scheme. The U.S. Geological Survey, in collaboration with Stanford University, is researching improvements to the modeling of the alluvial section, incorporating prior knowledge of geologic structure into the interpolation method and estimating the uncertainty of the modeled hydrogeologic units.

Depositional sequence analysis and sedimentologic modeling for improved prediction of Pennsylvanian reservoirs (Annex 1). Annual report, February 1, 1991--January 31, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watney, W.L.

1992-08-01

Interdisciplinary studies of the Upper Pennsylvanian Lansing and Kansas City groups have been undertaken in order to improve the geologic characterization of petroleum reservoirs and to develop a quantitative understanding of the processes responsible for formation of associated depositional sequences. To this end, concepts and methods of sequence stratigraphy are being used to define and interpret the three-dimensional depositional framework of the Kansas City Group. The investigation includes characterization of reservoir rocks in oil fields in western Kansas, description of analog equivalents in near-surface and surface sites in southeastern Kansas, and construction of regional structural and stratigraphic framework to linkmore » the site specific studies. Geologic inverse and simulation models are being developed to integrate quantitative estimates of controls on sedimentation to produce reconstructions of reservoir-bearing strata in an attempt to enhance our ability to predict reservoir characteristics.« less

Depositional sequence analysis and sedimentologic modeling for improved prediction of Pennsylvanian reservoirs (Annex 1)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watney, W.L.

1992-01-01

Interdisciplinary studies of the Upper Pennsylvanian Lansing and Kansas City groups have been undertaken in order to improve the geologic characterization of petroleum reservoirs and to develop a quantitative understanding of the processes responsible for formation of associated depositional sequences. To this end, concepts and methods of sequence stratigraphy are being used to define and interpret the three-dimensional depositional framework of the Kansas City Group. The investigation includes characterization of reservoir rocks in oil fields in western Kansas, description of analog equivalents in near-surface and surface sites in southeastern Kansas, and construction of regional structural and stratigraphic framework to linkmore » the site specific studies. Geologic inverse and simulation models are being developed to integrate quantitative estimates of controls on sedimentation to produce reconstructions of reservoir-bearing strata in an attempt to enhance our ability to predict reservoir characteristics.« less

A Hierarchical Multi-Model Approach for Uncertainty Segregation, Prioritization and Comparative Evaluation of Competing Modeling Propositions

NASA Astrophysics Data System (ADS)

Tsai, F. T.; Elshall, A. S.; Hanor, J. S.

2012-12-01

Subsurface modeling is challenging because of many possible competing propositions for each uncertain model component. How can we judge that we are selecting the correct proposition for an uncertain model component out of numerous competing propositions? How can we bridge the gap between synthetic mental principles such as mathematical expressions on one hand, and empirical observation such as observation data on the other hand when uncertainty exists on both sides? In this study, we introduce hierarchical Bayesian model averaging (HBMA) as a multi-model (multi-proposition) framework to represent our current state of knowledge and decision for hydrogeological structure modeling. The HBMA framework allows for segregating and prioritizing different sources of uncertainty, and for comparative evaluation of competing propositions for each source of uncertainty. We applied the HBMA to a study of hydrostratigraphy and uncertainty propagation of the Southern Hills aquifer system in the Baton Rouge area, Louisiana. We used geophysical data for hydrogeological structure construction through indictor hydrostratigraphy method and used lithologic data from drillers' logs for model structure calibration. However, due to uncertainty in model data, structure and parameters, multiple possible hydrostratigraphic models were produced and calibrated. The study considered four sources of uncertainties. To evaluate mathematical structure uncertainty, the study considered three different variogram models and two geological stationarity assumptions. With respect to geological structure uncertainty, the study considered two geological structures with respect to the Denham Springs-Scotlandville fault. With respect to data uncertainty, the study considered two calibration data sets. These four sources of uncertainty with their corresponding competing modeling propositions resulted in 24 calibrated models. The results showed that by segregating different sources of uncertainty, HBMA analysis provided insights on uncertainty priorities and propagation. In addition, it assisted in evaluating the relative importance of competing modeling propositions for each uncertain model component. By being able to dissect the uncertain model components and provide weighted representation of the competing propositions for each uncertain model component based on the background knowledge, the HBMA functions as an epistemic framework for advancing knowledge about the system under study.

Status report on the geology of the Oak Ridge Reservation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hatcher, R.D. Jr.; Lemiszki, P.J.; Foreman, J.L.

1992-10-01

This report provides an introduction to the present state of knowledge of the geology of the Oak Ridge Reservation (ORR) and a cursory introduction to the hydrogeology. An important element of this work is the construction of a modern detailed geologic map of the ORR (Plate 1), which remains in progress. An understanding of the geologic framework of the ORR is essential to many current and proposed activities related to land-use planning, waste management, environmental restoration, and waste remediation. Therefore, this report is also intended to convey the present state of knowledge of the geologic and geohydrologic framework of themore » ORR and vicinity and to present some of the available data that provide the basic framework for additional geologic mapping, subsurface geologic, and geohydrologic studies. In addition, some recently completed, detailed work on soils and other surficial materials is included because of the close relationships to bedrock geology and the need to recognize the weathered products of bedrock units. Weathering processes also have some influence on hydrologic systems and processes at depth.« less

Quantifying Conditions for Fault Self-Sealing in Geologic Carbon Sequestration

NASA Astrophysics Data System (ADS)

McPherson, B. J. O. L.; Patil, V.; Moore, J.; Trujillo, E. M.

2015-12-01

Injecting anthropogenic CO2 into a subsurface reservoir for sequestration will impact the reservoir significantly, including its geochemistry, porosity and permeability. If a fault or fracture penetrates the reservoir, CO2-laden brine may migrate into that fault, eventually sealing it via precipitation or opening it up via dissolution. The goal of this study was to identify and quantify such conditions of fault self-sealing or self-enhancing. We found that the dimensionless Damköhler number (Da), the ratio of reaction rate to advection rate, provides a meaningful framework for characterizing the propensity of (fault) systems to seal or open up. We developed our own framework wherein Damköhler numbers evolve spatiotemporally as opposed to the traditional single Da value approach. Our approach enables us to use the Damköhler for characterization of complex multiphase and multimineral reactive transport problems. We applied this framework to 1D fault models with eight conditions derived from four geologic compositions and two reservoir conditions. The four­ geologic compositions were chosen such that three out of them were representative of distinct geologic end-members (sandstone, mudstone and dolomitic limestone) and one was a mixed composition based on an average of three end-member compositions. The two sets of P-T conditions chosen included one set corresponding to CO2 in a gaseous phase ("shallow conditions") and the other corresponding to supercritical phase CO2 ("deep conditions"). Simulation results suggest that fault sealing via carbonate precipitation was a possibility for shallow conditions within limestone and mixed composition settings. The concentration of cations in the water was found to be an important control on the carbonate precipitation. The deep conditions models did not forecast self-sealing via carbonates. Sealing via clay precipitation is a likely possibility, but the 1000 year time-frame may be short for such. Model results indicated a range of Da values within which substantial reductions of fault porosity (meaning self-sealing) could be expected. A key conclusion suggested by the results of this study is that carbonate precipitation in the near-surface (top ~50-100 m) depths of a fault is the most likely mechanism of "self-sealing" for most geological settings.

The Cerrillos Uplift, the La Bajada Constriction, and Hydrogeologic Framework of the Santo Domingo Basin, Rio Grande Rift, New Mexico

USGS Publications Warehouse

Minor, Scott A.

2006-01-01

The geologic, geophysical, and hydrogeologic properties of the La Bajada constriction and Santo Domingo Basin, northern New Mexico, result from tectonic and volcanic processes of the late Tertiary and Quaternary Rio Grande rift. An integrated geologic and geophysical assessment in the La Bajada constriction allows development of a geologic framework that can provide input for regional ground-water flow models. These models then can provide better estimates of future water supplies in a region that largely subsists on aquifers in Rio Grande rift basins. The combination of surface geologic investigations (stratigraphic and structural studies; chapters A, B, C, and E), airborne geophysics (aeromagnetic and time-domain electromagnetic surveys; chapters D and F), ground geophysical measurements (gravity and magnetotelluric surveys; chapters D and F), and data from the few wells in the area (chapter G) provides new constraints on the hydrogeologic framework of this area. Summary results of our investigations are synthesized in chapter G. Through-going aquifers consisting of ancestral Rio Grande axial-river sand and gravel and of coarse western-piedmont gravel form the predominant ground-water pathways through the partly buried structural trough defining the La Bajada constriction between Espa?ola and Santo Domingo Basins. Thick, clay-rich Cretaceous marine shales of low hydraulic conductivity form a pervasive regional confining unit within the Cerrillos uplift on the southeast flank of the constriction. Numerous, dominantly north-northwest-striking, intrabasin faults that project part way across the La Bajada constriction create a matrix of laterally and vertically variable hydrogeologic compartments that locally partition and deflect ground-water flow parallel to faults.

Leverage and Delegation in Developing an Information Model for Geology

NASA Astrophysics Data System (ADS)

Cox, S. J.

2007-12-01

GeoSciML is an information model and XML encoding developed by a group of primarily geologic survey organizations under the auspices of the IUGS CGI. The scope of the core model broadly corresponds with information traditionally portrayed on a geologic map, viz. interpreted geology, some observations, the map legend and accompanying memoir. The development of GeoSciML has followed the methodology specified for an Application Schema defined by OGC and ISO 19100 series standards. This requires agreement within a community concerning their domain model, its formal representation using UML, documentation as a Feature Type Catalogue, with an XML Schema implementation generated from the model by applying a rule-based transformation. The framework and technology supports a modular governance process. Standard datatypes and GI components (geometry, the feature and coverage metamodels, metadata) are imported from the ISO framework. The observation and sampling model (including boreholes) is imported from OGC. The scale used for most scalar literal values (terms, codes, measures) allows for localization where necessary. Wildcards and abstract base- classes provide explicit extensibility points. Link attributes appear in a regular way in the encodings, allowing reference to external resources using URIs. The encoding is compatible with generic GI data-service interfaces (WFS, WMS, SOS). For maximum interoperability within a community, the interfaces may be specialised through domain-specified constraints (e.g. feature-types, scale and vocabulary bindings, query-models). Formalization using UML and XML allows use of standard validation and processing tools. Use of upper-level elements defined for generic GI application reduces the development effort and governance resonsibility, while maximising cross-domain interoperability. On the other hand, enabling specialization to be delegated in a controlled manner is essential to adoption across a range of subdisciplines and jurisdictions. The GeoSciML design team is responsible only for the part of the model that is unique to geology but for which general agreement can be reached within the domain. This paper is presented on behalf of the Interoperability Working Group of the IUGS Commission for Geoscience Information (CGI) - follow web-link for details of the membership.

Geologic control on the evolution of the inner shelf morphology offshore of the Mississippi barrier islands, northern Gulf of Mexico, USA

USGS Publications Warehouse

Flocks, James G.; Kindinger, Jack G.; Kelso, Kyle W.

2015-01-01

Between 2008 and 2013, high-resolution geophysical surveys were conducted around the Mississippi barrier islands and offshore. The sonar surveys included swath and single-beam bathymetry, sidescan, and chirp subbottom data collection. The geophysical data were groundtruthed using vibracore sediment collection. The results provide insight into the evolution of the inner shelf and the relationship between the near surface geologic framework and the morphology of the coastal zone. This study focuses on the buried Pleistocene fluvial deposits and late Holocene shore-oblique sand ridges offshore of Petit Bois Island and Petit Bois Pass. Prior to this study, the physical characteristics, evolution, and interrelationship of the ridges between both the shelf geology and the adjacent barrier island platform had not been evaluated. Numerous studies elsewhere along the coastal margin attribute shoal origin and sand-ridge evolution to hydrodynamic processes in shallow water (<20 m). Here we characterize the correlation between the geologic framework and surface morphology and demonstrate that the underlying stratigraphy must also be considered when developing an evolutionary conceptual model. It is important to understand this near surface, nearshore dynamic in order to understand how the stratigraphy influences the long-term response of the coastal zone to sea-level rise. The study also contributes to a growing body of work characterizing shore-oblique sand ridges which, along with the related geology, are recognized as increasingly important components to a nearshore framework whose origins and evolution must be understood and inventoried to effectively manage the coastal zone.

Geologic control on the evolution of the inner shelf morphology offshore of the Mississippi barrier islands, northern Gulf of Mexico, USA

NASA Astrophysics Data System (ADS)

Flocks, James G.; Kindinger, Jack L.; Kelso, Kyle W.

2015-06-01

Between 2008 and 2013, high-resolution geophysical surveys were conducted around the Mississippi barrier islands and offshore. The sonar surveys included swath and single-beam bathymetry, sidescan, and chirp subbottom data collection. The geophysical data were groundtruthed using vibracore sediment collection. The results provide insight into the evolution of the inner shelf and the relationship between the near surface geologic framework and the morphology of the coastal zone. This study focuses on the buried Pleistocene fluvial deposits and late Holocene shore-oblique sand ridges offshore of Petit Bois Island and Petit Bois Pass. Prior to this study, the physical characteristics, evolution, and interrelationship of the ridges between both the shelf geology and the adjacent barrier island platform had not been evaluated. Numerous studies elsewhere along the coastal margin attribute shoal origin and sand-ridge evolution to hydrodynamic processes in shallow water (<20 m). Here we characterize the correlation between the geologic framework and surface morphology and demonstrate that the underlying stratigraphy must also be considered when developing an evolutionary conceptual model. It is important to understand this near surface, nearshore dynamic in order to understand how the stratigraphy influences the long-term response of the coastal zone to sea-level rise. The study also contributes to a growing body of work characterizing shore-oblique sand ridges which, along with the related geology, are recognized as increasingly important components to a nearshore framework whose origins and evolution must be understood and inventoried to effectively manage the coastal zone.

Shallow groundwater in the Matanuska-Susitna Valley, Alaska—Conceptualization and simulation of flow

USGS Publications Warehouse

Kikuchi, Colin P.

2013-01-01

The Matanuska-Susitna Valley is in the Upper Cook Inlet Basin and is currently undergoing rapid population growth outside of municipal water and sewer service areas. In response to concerns about the effects of increasing water use on future groundwater availability, a study was initiated between the Alaska Department of Natural Resources and the U.S. Geological Survey. The goals of the study were (1) to compile existing data and collect new data to support hydrogeologic conceptualization of the study area, and (2) to develop a groundwater flow model to simulate flow dynamics important at the regional scale. The purpose of the groundwater flow model is to provide a scientific framework for analysis of regional-scale groundwater availability. To address the first study goal, subsurface lithologic data were compiled into a database and were used to construct a regional hydrogeologic framework model describing the extent and thickness of hydrogeologic units in the Matanuska-Susitna Valley. The hydrogeologic framework model synthesizes existing maps of surficial geology and conceptual geochronologies developed in the study area with the distribution of lithologies encountered in hundreds of boreholes. The geologic modeling package Geological Surveying and Investigation in Three Dimensions (GSI3D) was used to construct the hydrogeologic framework model. In addition to characterizing the hydrogeologic framework, major groundwater-budget components were quantified using several different techniques. A land-surface model known as the Deep Percolation Model was used to estimate in-place groundwater recharge across the study area. This model incorporates data on topography, soils, vegetation, and climate. Model-simulated surface runoff was consistent with observed streamflow at U.S. Geological Survey streamgages. Groundwater withdrawals were estimated on the basis of records from major water suppliers during 2004-2010. Fluxes between groundwater and surface water were estimated during field investigations on several small streams. Regional groundwater flow patterns were characterized by synthesizing previous water-table maps with a synoptic water-level measurement conducted during 2009. Time-series water-level data were collected at groundwater and lake monitoring stations over the study period (2009–present). Comparison of historical groundwater-level records with time-series groundwater-level data collected during this study showed similar patterns in groundwater-level fluctuation in response to precipitation. Groundwater-age data collected during previous studies show that water moves quickly through the groundwater system, suggesting that the system responds quickly to changes in climate forcing. Similarly, the groundwater system quickly returns to long-term average conditions following variability due to seasonal or interannual changes in precipitation. These analyses indicate that the groundwater system is in a state of dynamic equilibrium, characterized by water-level fluctuation about a constant average state, with no long-term trends in aquifer-system storage. To address the second study goal, a steady-state groundwater flow model was developed to simulate regional groundwater flow patterns. The groundwater flow model was bounded by physically meaningful hydrologic features, and appropriate internal model boundaries were specified on the basis of conceptualization of the groundwater system resulting in a three-layer model. Calibration data included 173 water‑level measurements and 18 measurements of streamflow gains and losses along small streams. Comparison of simulated and observed heads and flows showed that the model accurately simulates important regional characteristics of the groundwater flow system. This model is therefore appropriate for studying regional-scale groundwater availability. Mismatch between model-simulated and observed hydrologic quantities is likely because of the coarse grid size of the model and seasonal transient effects. Next steps towards model refinement include the development of a transient groundwater flow model that is suitable for analysis of seasonal variability in hydraulic heads and flows. In addition, several important groundwater budget components remain poorly quantified—including groundwater outflow to the Matanuska River, Little Susitna River, and Knik Arm.

Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

Professional Paper 1708 is intended primarily for geoscientists in academia, industry, and government who are interested in Appalachian basin geology and its coal and petroleum resources. Other users, however, may find the topics, papers, and digital images valuable for land-use and policy planning. Among the anticipated benefits of the report are improvements in (1) resource assessment estimates and methodology, (2) exploration strategies, (3) basin models, and (4) energy use policies.

Developing, deploying and reflecting on a web-based geologic simulation tool

NASA Astrophysics Data System (ADS)

Cockett, R.

2015-12-01

Geoscience is visual. It requires geoscientists to think and communicate about processes and events in three spatial dimensions and variations through time. This is hard(!), and students often have difficulty when learning and visualizing the three dimensional and temporal concepts. Visible Geology is an online geologic block modelling tool that is targeted at students in introductory and structural geology. With Visible Geology, students are able to combine geologic events in any order to create their own geologic models and ask 'what-if' questions, as well as interrogate their models using cross sections, boreholes and depth slices. Instructors use it as a simulation and communication tool in demonstrations, and students use it to explore concepts of relative geologic time, structural relationships, as well as visualize abstract geologic representations such as stereonets. The level of interactivity and creativity inherent in Visible Geology often results in a sense of ownership and encourages engagement, leading learners to practice visualization and interpretation skills and discover geologic relationships. Through its development over the last five years, Visible Geology has been used by over 300K students worldwide as well as in multiple targeted studies at the University of Calgary and at the University of British Columbia. The ease of use of the software has made this tool practical for deployment in classrooms of any size as well as for individual use. In this presentation, I will discuss the thoughts behind the implementation and layout of the tool, including a framework used for the development and design of new educational simulations. I will also share some of the surprising and unexpected observations on student interaction with the 3D visualizations, and other insights that are enabled by web-based development and deployment.

Adaptive dynamics on an environmental gradient that changes over a geological time-scale.

PubMed

Fortelius, Mikael; Geritz, Stefan; Gyllenberg, Mats; Toivonen, Jaakko

2015-07-07

The standard adaptive dynamics framework assumes two timescales, i.e. fast population dynamics and slow evolutionary dynamics. We further assume a third timescale, which is even slower than the evolutionary timescale. We call this the geological timescale and we assume that slow climatic change occurs within this timescale. We study the evolution of our model population over this very slow geological timescale with bifurcation plots of the standard adaptive dynamics framework. The bifurcation parameter being varied describes the abiotic environment that changes over the geological timescale. We construct evolutionary trees over the geological timescale and observe both gradual phenotypic evolution and punctuated branching events. We concur with the established notion that branching of a monomorphic population on an environmental gradient only happens when the gradient is not too shallow and not too steep. However, we show that evolution within the habitat can produce polymorphic populations that inhabit steep gradients. What is necessary is that the environmental gradient at some point in time is such that the initial branching of the monomorphic population can occur. We also find that phenotypes adapted to environments in the middle of the existing environmental range are more likely to branch than phenotypes adapted to extreme environments. Copyright © 2015 Elsevier Ltd. All rights reserved.

Integration of Geophysical Data into Structural Geological Modelling through Bayesian Networks

NASA Astrophysics Data System (ADS)

de la Varga, Miguel; Wellmann, Florian; Murdie, Ruth

2016-04-01

Structural geological models are widely used to represent the spatial distribution of relevant geological features. Several techniques exist to construct these models on the basis of different assumptions and different types of geological observations (e.g. Jessell et al., 2014). However, two problems are prevalent when constructing models: (i) observations and assumptions, and therefore also the constructed model, are subject to uncertainties, and (ii) additional information, such as geophysical data, is often available, but cannot be considered directly in the geological modelling step. In our work, we propose the integration of all available data into a Bayesian network including the generation of the implicit geological method by means of interpolation functions (Mallet, 1992; Lajaunie et al., 1997; Mallet, 2004; Carr et al., 2001; Hillier et al., 2014). As a result, we are able to increase the certainty of the resultant models as well as potentially learn features of our regional geology through data mining and information theory techniques. MCMC methods are used in order to optimize computational time and assure the validity of the results. Here, we apply the aforementioned concepts in a 3-D model of the Sandstone Greenstone Belt in the Archean Yilgarn Craton in Western Australia. The example given, defines the uncertainty in the thickness of greenstone as limited by Bouguer anomaly and the internal structure of the greenstone as limited by the magnetic signature of a banded iron formation. The incorporation of the additional data and specially the gravity provides an important reduction of the possible outcomes and therefore the overall uncertainty. References Carr, C. J., K. R. Beatson, B. J. Cherrie, J. T. Mitchell, R. W. Fright, C. B. McCallum, and R. T. Evans, 2001, Reconstruction and representation of 3D objects with radial basis functions: Proceedings of the 28th annual conference on Computer graphics and interactive techniques, 67-76. Jessell, M., Aillères, L., de Kemp, E., Lindsay, M., Wellmann, F., Hillier, M., ... & Martin, R. (2014). Next Generation Three-Dimensional Geologic Modeling and Inversion. Lajaunie, C., G. Courrioux, and L. Manuel, 1997, Foliation fields and 3D cartography in geology: Principles of a method based on potential interpolation: Mathematical Geology, 29, 571-584. Mallet, J.-L., 1992, Discrete smooth interpolation in geometric modelling: Computer-Aided Design, 24, 178-191 Mallet, L. J., 2004, Space-time mathematical framework for sedimentary geology: Mathematical Geology, 36, 1-32.

Semantics-informed cartography: the case of Piemonte Geological Map

NASA Astrophysics Data System (ADS)

Piana, Fabrizio; Lombardo, Vincenzo; Mimmo, Dario; Giardino, Marco; Fubelli, Giandomenico

2016-04-01

In modern digital geological maps, namely those supported by a large geo-database and devoted to dynamical, interactive representation on WMS-WebGIS services, there is the need to provide, in an explicit form, the geological assumptions used for the design and compilation of the database of the Map, and to get a definition and/or adoption of semantic representation and taxonomies, in order to achieve a formal and interoperable representation of the geologic knowledge. These approaches are fundamental for the integration and harmonisation of geological information and services across cultural (e.g. different scientific disciplines) and/or physical barriers (e.g. administrative boundaries). Initiatives such as GeoScience Markup Language (last version is GeoSciML 4.0, 2015, http://www.geosciml.org) and the INSPIRE "Data Specification on Geology" http://inspire.jrc.ec.europa.eu/documents/Data_Specifications/INSPIRE_DataSpecification_GE_v3.0rc3.pdf (an operative simplification of GeoSciML, last version is 3.0 rc3, 2013), as well as the recent terminological shepherding of the Geoscience Terminology Working Group (GTWG) have been promoting information exchange of the geologic knowledge. Grounded on these standard vocabularies, schemas and data models, we provide a shared semantic classification of geological data referring to the study case of the synthetic digital geological map of the Piemonte region (NW Italy), named "GEOPiemonteMap", developed by the CNR Institute of Geosciences and Earth Resources, Torino (CNR IGG TO) and hosted as a dynamical interactive map on the geoportal of ARPA Piemonte Environmental Agency. The Piemonte Geological Map is grounded on a regional-scale geo-database consisting of some hundreds of GeologicUnits whose thousands instances (Mapped Features, polygons geometry) widely occur in Piemonte region, and each one is bounded by GeologicStructures (Mapped Features, line geometry). GeologicUnits and GeologicStructures have been spatially correlated through the whole region and described using the GeoSciML vocabularies. A hierarchical schema is provided for the Piemonte Geological Map that gives the parental relations between several orders of GeologicUnits referring to mostly recurring geological objects and main GeologicEvents, in a logical framework compliant with GeoSciML and INSPIRE data models. The classification criteria and the Hierarchy Schema used to define the GEOPiemonteMap Legend, as well as the intended meanings of the geological concepts used to achieve the overall classification schema, are explicitly described in several WikiGeo pages (implemented by "MediaWiki" open source software, https://www.mediawiki.org/wiki/MediaWiki). Moreover, a further step toward a formal classification of the contents (both data and interpretation) of the GEOPiemonteMap was triggered, by setting up an ontological framework, named "OntoGeonous", in order to achieve a thorough semantic characterization of the Map.

Delineation of the hydrogeologic framework of the Big Sioux aquifer near Sioux Falls, South Dakota, using airborne electromagnetic data

USGS Publications Warehouse

Valseth, Kristen J.; Delzer, Gregory C.; Price, Curtis V.

2018-03-21

The U.S. Geological Survey, in cooperation with the City of Sioux Falls, South Dakota, began developing a groundwater-flow model of the Big Sioux aquifer in 2014 that will enable the City to make more informed water management decisions, such as delineation of areas of the greatest specific yield, which is crucial for locating municipal wells. Innovative tools are being evaluated as part of this study that can improve the delineation of the hydrogeologic framework of the aquifer for use in development of a groundwater-flow model, and the approach could have transfer value for similar hydrogeologic settings. The first step in developing a groundwater-flow model is determining the hydrogeologic framework (vertical and horizontal extents of the aquifer), which typically is determined by interpreting geologic information from drillers’ logs and surficial geology maps. However, well and borehole data only provide hydrogeologic information for a single location; conversely, nearly continuous geophysical data are collected along flight lines using airborne electromagnetic (AEM) surveys. These electromagnetic data are collected every 3 meters along a flight line (on average) and subsequently can be related to hydrogeologic properties. AEM data, coupled with and constrained by well and borehole data, can substantially improve the accuracy of aquifer hydrogeologic framework delineations and result in better groundwater-flow models. AEM data were acquired using the Resolve frequency-domain AEM system to map the Big Sioux aquifer in the region of the city of Sioux Falls. The survey acquired more than 870 line-kilometers of AEM data over a total area of about 145 square kilometers, primarily over the flood plain of the Big Sioux River between the cities of Dell Rapids and Sioux Falls. The U.S. Geological Survey inverted the survey data to generate resistivity-depth sections that were used in two-dimensional maps and in three-dimensional volumetric visualizations of the Earth resistivity distribution. Contact lines were drawn using a geographic information system to delineate interpreted geologic stratigraphy. The contact lines were converted to points and then interpolated into a raster surface. The methods used to develop elevation and depth maps of the hydrogeologic framework of the Big Sioux aquifer are described herein.The final AEM interpreted aquifer thickness ranged from 0 to 31 meters with an average thickness of 12.8 meters. The estimated total volume of the aquifer was 1,060,000,000 cubic meters based on the assumption that the top of the aquifer is the land-surface elevation. A simple calculation of the volume (length times width times height) of a previous delineation of the aquifer estimated the aquifer volume at 378,000,000 cubic meters; thus, the estimation based on AEM data is more than twice the previous estimate. The depth to top of Sioux Quartzite, which ranged in depth from 0 to 90 meters, also was delineated from the AEM data.

Multi-criteria Resource Mapping and its Relevance in the Assessment of Habitat Changes

NASA Astrophysics Data System (ADS)

Van Lancker, V. R.; Kint, L.; van Heteren, S.

2016-02-01

Mineral and geological resources can be considered to be non-renewable on time scales relevant for decision makers. Once exhausted by humans, they are not replenished rapidly enough by nature, meaning that truly sustainable resource exploitation is not possible. Comprehensive knowledge on the distribution, composition and dynamics of geological resources and on the environmental impact of aggregate extraction is therefore critical. For the Belgian and southern Netherlands part of the North Sea, being representative of a typical sandbank system, a 4D resource decision-support system is being developed that links 3D geological models with environmental impact models. Aim is to quantify natural and man-made changes and to define from these sustainable exploitation thresholds. These are needed to ensure that recovery from perturbations is rapid and secure, and that the range of natural variation is maintained, a prerequisite stated in Europe's Marine Strategy Framework Directive, the environmental pillar of Europe's Maritime Policy. The geological subsurface is parameterised using a voxel modelling approach. Primarily, the voxels, or volume blocks of information, are constrained by the geology, based on coring and seismic data, but they are open to any resource-relevant information. The primary geological data entering the voxels are subdued to uncertainty modelling, a necessary step to produce data products with confidence limits. The presentation will focus on the novelty this approach brings for seabed and habitat mapping. In our model this is the upper voxel, providing the advantage of having a dynamical coupling to the geology and a suite of environmental parameters. In the context of assessing habitat changes, this coupling enables to account for spatial and temporal variability, seabed heterogeneity, as well as data uncertainty. The project is funded by Belgian Science Policy and is further valorised through EMODnet-Geology (DG MARE).

Site descriptive modeling as a part of site characterization in Sweden - Concluding the surface based investigations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersson, Johan; Winberg, Anders; Skagius, Kristina

The Swedish Nuclear Fuel and Waste Management Co., SKB, is currently finalizing its surface based site investigations for the final repository for spent nuclear fuel in the municipalities of Oestharmnar (the Forsmark area) and Oskarshamn (the Simpevar/Laxemar area). The investigation data are assessed into a Site Descriptive Model, constituting a synthesis of geology, rock mechanics, thermal properties, hydrogeology, hydro-geochemistry, transport properties and a surface system description. Site data constitute a wide range of different measurement results. These data both need to be checked for consistency and to be interpreted into a format more amenable for three-dimensional modeling. The three-dimensional modelingmore » (i.e. estimating the distribution of parameter values in space) is made in a sequence where the geometrical framework is taken from the geological models and in turn used by the rock mechanics, thermal and hydrogeological modeling. These disciplines in turn are partly interrelated, and also provide feedback to the geological modeling, especially if the geological description appears unreasonable when assessed together with the other data. Procedures for assessing the uncertainties and the confidence in the modeling have been developed during the course of the site modeling. These assessments also provide key input to the completion of the site investigation program. (authors)« less

3d-modelling workflows for trans-nationally shared geological models - first approaches from the project GeoMol

NASA Astrophysics Data System (ADS)

Rupf, Isabel

2013-04-01

To meet the EU's ambitious targets for carbon emission reduction, renewable energy production has to be strongly upgraded and made more efficient for grid energy storage. Alpine Foreland Basins feature a unique geological inventory which can contribute substantially to tackle these challenges. They offer a geothermal potential and storage capacity for compressed air, as well as space for underground storage of CO2. Exploiting these natural subsurface resources will strongly compete with existing oil and gas claims and groundwater issues. The project GeoMol will provide consistent 3-dimensional subsurface information about the Alpine Foreland Basins based on a holistic and transnational approach. Core of the project GeoMol is a geological framework model for the entire Northern Molasse Basin, complemented by five detailed models in pilot areas, also in the Po Basin, which are dedicated to specific questions of subsurface use. The models will consist of up to 13 litho-stratigraphic horizons ranging from the Cenozoic basin fill down to Mesozoic and late Paleozoic sedimentary rocks and the crystalline basement. More than 5000 wells and 28 000 km seismic lines serve as input data sets for the geological subsurface model. The data have multiple sources and various acquisition dates, and their interpretations have gone through several paradigm changes. Therefore, it is necessary to standardize the data with regards to technical parameters and content prior to further analysis (cf. Capar et al. 2013, EGU2013-5349). Each partner will build its own geological subsurface model with different software solutions for seismic interpretation and 3d-modelling. Therefore, 3d-modelling follows different software- and partner-specific workflows. One of the main challenges of the project is to ensure a seamlessly fitting framework model. It is necessary to define several milestones for cross border checks during the whole modelling process. Hence, the main input data set of the framework model are interpreted seismic lines, 3d-models can be generated either in time or in depth domain. Some partners will build their 3d-model in time domain and convert it after finishing to depth. Other participants will transform seismic information first and will model directly in depth domain. To ensure comparability between the different parts transnational velocity models for time-depth conversion are required at an early stage of the project. The exchange of model geometries, topology, and geo-scientific content will be achieved applying an appropriate cyberinfrastructure called GST. It provides functionalities to ensure semantic and technical interoperability. Within the project GeoMol a web server for the dissemination of 3d geological models will be implemented including an administrative interface for the role-based access, real-time transformation of country-specific coordinate systems and a web visualisation features. The project GeoMol is co-funded by the Alpine Space Program as part of the European Territorial Cooperation 2007-2013. The project integrates partners from Austria, France, Germany, Italy, Slovenia and Switzerland and runs from September 2012 to June 2015. Further information on www.geomol.eu. The GeoMol 3D-modelling team: Roland Baumberger (swisstopo), Magdalena Bottig (GBA), Alessandro Cagnoni (RLB), Laure Capar (BRGM), Renaud Couëffé (BRGM), Chiara D'Ambrogi (ISPRA), Chrystel Dezayes (BRGM), Gerold Diepolder (LfU BY), Charlotte Fehn (LGRB), Sunseare Gabalda (BRGM), Gregor Götzl (GBA), Andrej Lapanje (GeoZS), Fabio Carlo Molinari (RER-SGSS), Edgar Nitsch (LGRB), Robert Pamer (LfU BY), Sebastian Pfleiderer (GBA), Marco Pantaloni (ISPRA), Uta Schulz (LfU BY), Günter Sokol (LGRB), Gunther Wirsing (LGRB), Heiko Zumsprekel (LGRB)

Hydrogeologic Framework of the Upper Santa Cruz Basin (Arizona and Sonora) using Well Logs, Geologic Mapping, Gravity, Magnetics, and Electromagnetics

NASA Astrophysics Data System (ADS)

Callegary, J. B.; Page, W. R.; Megdal, S.; Gray, F.; Scott, C. A.; Berry, M.; Rangel, M.; Oroz Ramos, L.; Menges, C. M.; Jones, A.

2011-12-01

In 2006, the U.S. Congress passed the U.S.-Mexico Transboundary Aquifer Assessment Act which provides a framework for study of aquifers shared by the United States and Mexico. The aquifer of the Upper Santa Cruz Basin was chosen as one of four priority aquifers for several reasons, including water scarcity, a population greater than 300,000, groundwater as the sole source of water for human use, and a riparian corridor that is of regional significance for migratory birds and other animals. Several new mines are also being proposed for this area which may affect water quality and availability. To date, a number of studies have been carried out by a binational team composed of the U.S. Geological Survey, the Mexican National Water Commission, and the Universities of Arizona and Sonora. Construction of a cross-border hydrogeologic framework model of the basin between Amado, Arizona and its southern boundary in Sonora is currently a high priority. The relatively narrow Santa Cruz valley is a structural basin that did not experience the same degree of late Cenozoic lateral extension and consequent deepening as found in other basin-and-range alluvial basins, such as the Tucson basin, where basin depth exceeds 3000 meters. This implies that storage may be much less than that found in other basin-and-range aquifers. To investigate the geometry of the basin and facies changes within the alluvium, a database of over one thousand well logs has been developed, geologic mapping and transient electromagnetic (TEM) surveys have been carried out, and information from previous electromagnetic, magnetic, and gravity studies is being incorporated into the hydrogeologic framework. Initial geophysical surveys and analyses have focused on the portion of the basin west of Nogales, Arizona, because it supplies approximately 50% of that city's water. Previous gravity and magnetic modeling indicate that this area is a narrow, fault-controlled half graben. Preliminary modeling of airborne and ground-based transient electromagnetic surveys corroborates earlier conclusions from the gravity modeling that depth to bedrock is greater than 500 meters in some locations. Results from other portions of the study area including Mexico are still being evaluated and incorporated into the three-dimensional hydrologic framework which will ultimately be used to construct a groundwater flow model.

Deep resistivity structure of Yucca Flat, Nevada Test Site, Nevada

USGS Publications Warehouse

Asch, Theodore H.; Rodriguez, Brian D.; Sampson, Jay A.; Wallin, Erin L.; Williams, Jackie M.

2006-01-01

The Department of Energy (DOE) and the National Nuclear Security Administration (NNSA) at their Nevada Site Office are addressing groundwater contamination resulting from historical underground nuclear testing through the Environmental Management program and, in particular, the Underground Test Area project. One issue of concern is the nature of the somewhat poorly constrained pre Tertiary geology and its effects on ground-water flow in the area adjacent to a nuclear test. Ground water modelers would like to know more about the hydrostratigraphy and geologic structure to support a hydrostratigraphic framework model that is under development for the Yucca Flat Corrective Action Unit (CAU). During 2003, the U.S. Geological Survey, supported by the DOE and NNSA-NSO, collected and processed data from 51 magnetotelluric (MT) and audio-magnetotelluric (AMT) stations at the Nevada Test Site in and near Yucca Flat to assist in characterizing the pre-Tertiary geology in that area. The primary purpose was to refine the character, thickness, and lateral extent of pre Tertiary confining units. In particular, a major goal has been to define the upper clastic confining unit (late Devonian - Mississippian-age siliciclastic rocks assigned to the Eleana Formation and Chainman Shale) in the Yucca Flat area. The MT and AMT data have been released in separate USGS Open File Reports. The Nevada Test Site magnetotelluric data interpretation presented in this report includes the results of detailed two-dimensional (2 D) resistivity modeling for each profile (including alternative interpretations) and gross inferences on the three dimensional (3 D) character of the geology beneath each station. The character, thickness, and lateral extent of the Chainman Shale and Eleana Formation that comprise the Upper Clastic Confining Unit are generally well determined in the upper 5 km. Inferences can be made regarding the presence of the Lower Clastic Confining Unit at depths below 5 km. Large fault structures such as the CP Thrust fault, the Carpetbag fault, and the Yucca fault that cross Yucca Flat are also discernable as are other smaller faults. The subsurface electrical resistivity distribution and inferred geologic structures determined by this investigation should help constrain the hydrostratigraphic framework model that is under development.

Conceptual model of the Great Basin carbonate and alluvial aquifer system

USGS Publications Warehouse

Heilweil, Victor M.; Brooks, Lynette E.

2011-01-01

A conceptual model of the Great Basin carbonate and alluvial aquifer system (GBCAAS) was developed by the U.S. Geological Survey (USGS) for a regional assessment of groundwater availability as part of a national water census. The study area is an expansion of a previous USGS Regional Aquifer Systems Analysis (RASA) study conducted during the 1980s and 1990s of the carbonate-rock province of the Great Basin. The geographic extent of the study area is 110,000 mi2, predominantly in eastern Nevada and western Utah, and includes 165 hydrographic areas (HAs) and 17 regional groundwater flow systems.A three-dimensional hydrogeologic framework was constructed that defines the physical geometry and rock types through which groundwater moves. The diverse sedimentary units of the GBCAAS study area are grouped into hydrogeologic units (HGUs) that are inferred to have reasonably distinct hydrologic properties due to their physical characteristics. These HGUs are commonly disrupted by large-magnitude offset thrust, strike-slip, and normal faults, and locally affected by caldera formation. The most permeable aquifer materials within the study area include Cenozoic unconsolidated sediments and volcanic rocks, along with Mesozoic and Paleozoic carbonate rocks. The framework was built by extracting and combining information from digital elevation models, geologic maps, cross sections, drill hole logs, existing hydrogeologic frameworks, and geophysical data.

Development of an Anisotropic Geological-Based Land Use Regression and Bayesian Maximum Entropy Model for Estimating Groundwater Radon across Northing Carolina

NASA Astrophysics Data System (ADS)

Messier, K. P.; Serre, M. L.

2015-12-01

Radon (222Rn) is a naturally occurring chemically inert, colorless, and odorless radioactive gas produced from the decay of uranium (238U), which is ubiquitous in rocks and soils worldwide. Exposure to 222Rn is likely the second leading cause of lung cancer after cigarette smoking via inhalation; however, exposure through untreated groundwater is also a contributing factor to both inhalation and ingestion routes. A land use regression (LUR) model for groundwater 222Rn with anisotropic geological and 238U based explanatory variables is developed, which helps elucidate the factors contributing to elevated 222Rn across North Carolina. Geological and uranium based variables are constructed in elliptical buffers surrounding each observation such that they capture the lateral geometric anisotropy present in groundwater 222Rn. Moreover, geological features are defined at three different geological spatial scales to allow the model to distinguish between large area and small area effects of geology on groundwater 222Rn. The LUR is also integrated into the Bayesian Maximum Entropy (BME) geostatistical framework to increase accuracy and produce a point-level LUR-BME model of groundwater 222Rn across North Carolina including prediction uncertainty. The LUR-BME model of groundwater 222Rn results in a leave-one out cross-validation of 0.46 (Pearson correlation coefficient= 0.68), effectively predicting within the spatial covariance range. Modeled results of 222Rn concentrations show variability among Intrusive Felsic geological formations likely due to average bedrock 238U defined on the basis of overlying stream-sediment 238U concentrations that is a widely distributed consistently analyzed point-source data.

How Do Novice and Expert Learners Represent, Understand, and Discuss Geologic Time?

NASA Astrophysics Data System (ADS)

Layow, Erica Amanda

This dissertation examined the representations novice and expert learners constructed for the geologic timescale. Learners engaged in a three-part activity. The purpose was to compare novice learners' representations to those of expert learners. This provided insight into the similarities and differences between their strategies for event ordering, assigning values and scale to the geologic timescale model, as well as their language and practices to complete the model. With a qualitative approach to data analysis informed by an expert-novice theoretical framework grounded in phenomenography, learner responses comprised the data analyzed. These data highlighted learners' metacognitive thoughts that might not otherwise be shared through lectures or laboratory activities. Learners' responses were analyzed using a discourse framework that positioned learners as knowers. Novice and expert learners both excelled at ordering and discussing events before the Phanerozoic, but were challenged with events during the Phanerozoic. Novice learners had difficulty assigning values to events and establishing a scale for their models. Expert learners expressed difficulty with determining a scale because of the size of the model, yet eventually used anchor points and unitized the model to establish a scale. Despite challenges constructing their models, novice learners spoke confidently using claims and few hedging phrases indicating their confidence in statements made. Experts used more hedges than novices, however the hedging comments were made about more complex conceptions. Using both phenomenographic and discourse analysis approaches for analysis foregrounded learners' discussions of how they perceived geologic time and their ways of knowing and doing. This research is intended to enhance the geoscience community's understanding of the ways novice and expert learners think and discuss conceptions of geologic time, including the events and values of time, and the strategies used to determine accuracy of scale. This knowledge will provide a base from which to support geoscience curriculum development at the university level, specifically to design activities that will not only engage and express learners' metacognitive scientific practices, but to encourage their construction of scientific identities and membership in the geoscience community.

Geologic and hydrogeologic framework of the Espanola Basin -- proceedings of the 4th annual Espanola Basin Workshop, Santa Fe, New Mexico, March 1-3, 2005

USGS Publications Warehouse

McKinney, Kevin C.

2005-01-01

This report presents abstracts of technical studies that pertain to the hydrogeologic framework of the Espa?ola basin, a major subbasin of the Cenozoic Rio Grande rift. Sediments and interbedded volcanic rocks that fill the Espa?ola basin comprise an aquifer system that is an important source of water for many residents of the basin, including people in the cities of Santa Fe, Espa?ola, and Los Alamos as well as Native Americans in eleven Pueblos. The abstracts describe results of technical studies that were presented either as poster exhibits or oral presentations at the forth-annual Espa?ola basin workshop, held March 1-2 of 2005 in Santa Fe, New Mexico. The principal goal of this workshop was to share information about ongoing studies. The Espa?ola basin workshop was hosted by the Espa?ola basin technical advisory group (EBTAG) and sponsored by the U.S. Geological Survey, the New Mexico Bureau of Geology and Mineral Resources, and both the Water Research Technical Assistance Office and the Groundwater Protection Program of Los Alamos National Laboratory. Abstracts in this report have been grouped into six information themes: Basic Water Data, Water Quality and Water Chemistry, Water Balance and Stream/Aquifer Interaction, Data Integration and Hydrologic Model Testing, Three-Dimensional Hydrogeological Architecture, and Geologic Framework. Taken together, the abstracts in this report provide a view of the current status of hydrogeologic research within the Espa?ola basin.

Preliminary three-dimensional geohydrologic framework of the San Antonio Creek Groundwater Basin, Santa Barbara County, California

NASA Astrophysics Data System (ADS)

Cromwell, G.; Sweetkind, D. S.; O'leary, D. R.

2017-12-01

The San Antonio Creek Groundwater Basin is a rural agricultural area that is heavily dependent on groundwater to meet local water demands. The U.S. Geological Survey (USGS) is working cooperatively with Santa Barbara County and Vandenberg Air Force Base to assess the quantity and quality of the groundwater resources within the basin. As part of this assessment, an integrated hydrologic model that will help stakeholders to effectively manage the water resources in the basin is being developed. The integrated hydrologic model includes a conceptual model of the subsurface geology consisting of stratigraphy and variations in lithology throughout the basin. The San Antonio Creek Groundwater Basin is a relatively narrow, east-west oriented valley that is structurally controlled by an eastward-plunging syncline. Basin-fill material beneath the valley floor consists of relatively coarse-grained, permeable, marine and non-marine sedimentary deposits, which are underlain by fine-grained, low-permeability, marine sedimentary rocks. To characterize the system, surficial and subsurface geohydrologic data were compiled from geologic maps, existing regional geologic models, and lithology and geophysical logs from boreholes, including two USGS multiple-well sites drilled as part of this study. Geohydrologic unit picks and lithologic variations are incorporated into a three-dimensional framework model of the basin. This basin (model) includes six geohydrologic units that follow the structure and stratigraphy of the area: 1) Bedrock - low-permeability marine sedimentary rocks; 2) Careaga Formation - fine to coarse grained near-shore sandstone; 3) Paso Robles Formation, lower portion - sandy-gravely deposits with clay and limestone; 4) Paso Robles Formation, middle portion - clayey-silty deposits; 5) Paso Robles Formation, upper portion - sandy-gravely deposits; and 6) recent Quaternary deposits. Hydrologic data show that the upper and lower portions of the Paso Robles Formation are the primary grou­ndwater-bearing units within the basin, and that the fine-grained layer within this Formation locally restricts vertical groundwater flow.

Three-dimensional geologic mapping of the Cenozoic basin fill, Amargosa Desert basin, Nevada and California

USGS Publications Warehouse

Taylor, Emily M.; Sweetkind, Donald S.

2014-01-01

Understanding the subsurface geologic framework of the Cenozoic basin fill that underlies the Amargosa Desert in southern Nevada and southeastern California has been improved by using borehole data to construct three-dimensional lithologic and interpreted facies models. Lithologic data from 210 boreholes from a 20-kilometer (km) by 90-km area were reduced to a limited suite of descriptors based on geologic knowledge of the basin and distributed in three-dimensional space using interpolation methods. The resulting lithologic model of the Amargosa Desert basin portrays a complex system of interfingered coarse- to fine-grained alluvium, playa and palustrine deposits, eolian sands, and interbedded volcanic units. Lithologic units could not be represented in the model as a stacked stratigraphic sequence due to the complex interfingering of lithologic units and the absence of available time-stratigraphic markers. Instead, lithologic units were grouped into interpreted genetic classes, such as playa or alluvial fan, to create a three-dimensional model of the interpreted facies data. Three-dimensional facies models computed from these data portray the alluvial infilling of a tectonically formed basin with intermittent internal drainage and localized regional groundwater discharge. The lithologic and interpreted facies models compare favorably to resistivity, aeromagnetic, and geologic map data, lending confidence to the interpretation.

The key to commercial-scale geological CO2 sequestration: Displaced fluid management

USGS Publications Warehouse

Surdam, R.C.; Jiao, Z.; Stauffer, P.; Miller, T.

2011-01-01

The Wyoming State Geological Survey has completed a thorough inventory and prioritization of all Wyoming stratigraphic units and geologic sites capable of sequestering commercial quantities of CO2 (5-15 Mt CO 2/year). This multi-year study identified the Paleozoic Tensleep/Weber Sandstone and Madison Limestone (and stratigraphic equivalent units) as the leading clastic and carbonate reservoir candidates for commercial-scale geological CO2 sequestration in Wyoming. This conclusion was based on unit thickness, overlying low permeability lithofacies, reservoir storage and continuity properties, regional distribution patterns, formation fluid chemistry characteristics, and preliminary fluid-flow modeling. This study also identified the Rock Springs Uplift in southwestern Wyoming as the most promising geological CO2 sequestration site in Wyoming and probably in any Rocky Mountain basin. The results of the WSGS CO2 geological sequestration inventory led the agency and colleagues at the UW School of Energy Resources Carbon Management Institute (CMI) to collect available geologic, petrophysical, geochemical, and geophysical data on the Rock Springs Uplift, and to build a regional 3-D geologic framework model of the Uplift. From the results of these tasks and using the FutureGen protocol, the WSGS showed that on the Rock Springs Uplift, the Weber Sandstone has sufficient pore space to sequester 18 billion tons (Gt) of CO2, and the Madison Limestone has sufficient pore space to sequester 8 Gt of CO2. ?? 2011 Published by Elsevier Ltd.

Health, Safety, and Environmental Screening and Ranking Frameworkfor Geologic CO2 Storage Site Selection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oldenburg, Curtis M.

2005-09-19

This report describes a screening and ranking framework(SRF) developed to evaluate potential geologic carbon dioxide (CO2) storage sites on the basis of health, safety, and environmental (HSE) risk arising from possible CO2 leakage. The approach is based on the assumption that HSE risk due to CO2 leakage is dependent on three basic characteristics of a geologic CO2 storage site: (1) the potential for primary containment by the target formation; (2) the potential for secondary containment if the primary formation leaks; and (3) the potential for attenuation and dispersion of leaking CO2 if the primary formation leaks and secondary containment fails.more » The framework is implemented in a spreadsheet in which users enter numerical scores representing expert opinions or general information available from published materials along with estimates of uncertainty to evaluate the three basic characteristics in order to screen and rank candidate sites. Application of the framework to the Rio Visa Gas Field, Ventura Oil Field, and Mammoth Mountain demonstrates the approach. Refinements and extensions are possible through the use of more detailed data or model results in place of property proxies. Revisions and extensions to improve the approach are anticipated in the near future as it is used and tested by colleagues and collaborators.« less

Facies dimensions within carbonate reservoirs - guidelines from satellite images of modern analogs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, P.M.; Kowalik, W.S.

1995-08-01

Modern analogs illustrate the distribution of carbonate facies within an overall depositional setting and can be an integral part of a subsurface geologic model in indicating the dimensions, trend, and interrelationships of facies that might be related to reservoir and non-reservoir distribution. Satellite images from several modern carbonate areas depict the geologic characteristics that can be expected in ancient shallow-water settings. Isolated carbonate platforms- the Bahamas, Caicos Platform in the British West Indies, Chinchorro Bank offshore of Yucatan, and portions of the Belize area; Ramp-style shelf-to-basin transitions - Abu Dhabi and northern Yucatan; Rimmed shelf margins - South Florida, portionsmore » of Belize, and the Great Barrier Reef of Australia; Broad, deep shelf lagoons - the Great Barrier Reef and Belize; Reef variability - South Florida, the Bahamas, Caicos, Northern Yucatan, and Abu Dhabi; Shallow lagoon/tidal flat settings - South Florida, the Bahamas, Caicos, Northern Yucatan, Shark Bay in Western Australia, Abu Dhabi; Mixed carbonate and siliciclastic depostion - South Florida, Belize, the Great Barrier Reef, Shark Bay and Abu Dhabi. The geologic framework as illustrated by these areas is important at the development scale where lateral variation of porosity and permeability, i.e. reservoir quality, is commonly tied to facies changes and facies dimensions are required as input to reservoir models. The geologic framework is essential at the exploration scale for reservoir facies prediction and stratigraphic play concepts which are related directly to depositional facies patterns.« less

Geosites and geoheritage representations - a cartographic approach

NASA Astrophysics Data System (ADS)

Rocha, Joao; Brilha, José

2016-04-01

In recent years, the increasing awareness of the importance of nature conservation, particularly towards the protection, conservation and promotion of geological sites, has resulted in a wide range of scientific studies. In a certain way, the majority of geodiversity studies, geoconservation strategies and geosites inventories and geoheritage assessment projects will use, on a particular stage, a cartographic representation - a map - of the most relevant geological and geomorphological features within the area of analyses. A wide range of geosite maps and geological heritage maps have been produced but, so far, a widely accepted conceptual cartographic framework with a specific symbology for cartographic representation has not been created. In this work we debate the lack of a systematic and conceptual framework to support geoheritage and geosite mapping. It is important to create a widely accepted conceptual cartographic framework with a specific symbology to be used within maps dedicated to geoheritage and geosites. We propose a cartographic approach aiming the conceptualization and the definition of a nomenclature and symbology system to be used on both geosite and geoheritage maps. We define a symbology framework for geosite and geoheritage mapping addressed to general public and to secondary school students, in order to be used as geotouristic and didactic tools, respectively. Three different approaches to support the definition of the symbology framework were developed: i) symbols to correlate geosites with the geological time scale; ii) symbols related to each one of the 27 geological frameworks defined in the Portuguese geoheritage inventory; iii) symbols to represent groups of geosites that share common geological and geomorphological features. The use of these different symbols in a map allows a quick understanding of a set of relevant information, in addition to the usual geographical distribution of geosites in a certain area.

Delineating Hydrofacies Spatial Distribution by Integrating Ensemble Data Assimilation and Indicator Geostatistics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Xuehang; Chen, Xingyuan; Ye, Ming

2015-07-01

This study develops a new framework of facies-based data assimilation for characterizing spatial distribution of hydrofacies and estimating their associated hydraulic properties. This framework couples ensemble data assimilation with transition probability-based geostatistical model via a parameterization based on a level set function. The nature of ensemble data assimilation makes the framework efficient and flexible to be integrated with various types of observation data. The transition probability-based geostatistical model keeps the updated hydrofacies distributions under geological constrains. The framework is illustrated by using a two-dimensional synthetic study that estimates hydrofacies spatial distribution and permeability in each hydrofacies from transient head data.more » Our results show that the proposed framework can characterize hydrofacies distribution and associated permeability with adequate accuracy even with limited direct measurements of hydrofacies. Our study provides a promising starting point for hydrofacies delineation in complex real problems.« less

Gaining the necessary geologic, hydrologic, and geochemical understanding for additional brackish groundwater development, coastal San Diego, California, USA

USGS Publications Warehouse

Danskin, Wesley R.

2012-01-01

Local water agencies and the United States Geological Survey are using a combination of techniques to better understand the scant freshwater resources and the much more abundant brackish resources in coastal San Diego, California, USA. Techniques include installation of multiple-depth monitoring well sites; geologic and paleontological analysis of drill cuttings; geophysical logging to identify formations and possible seawater intrusion; sampling of pore-water obtained from cores; analysis of chemical constituents including trace elements and isotopes; and use of scoping models including a three-dimensional geologic framework model, rainfall-runoff model, regional groundwater flow model, and coastal density-dependent groundwater flow model. Results show that most fresh groundwater was recharged during the last glacial period and that the coastal aquifer has had recurring intrusions of fresh and saline water. These intrusions disguise the source, flowpaths, and history of ground water near the coast. The flow system includes a freshwater lens resting on brackish water; a 100-meter-thick flowtube of freshwater discharging under brackish estuarine water and above highly saline water; and broad areas of fine-grained coastal sediment filled with fairly uniform brackish water. Stable isotopes of hydrogen and oxygen indicate the recharged water flows through many kilometers of fractured crystalline rock before entering the narrow coastal aquifer.

Bayesian Chance-Constrained Hydraulic Barrier Design under Geological Structure Uncertainty.

PubMed

Chitsazan, Nima; Pham, Hai V; Tsai, Frank T-C

2015-01-01

The groundwater community has widely recognized geological structure uncertainty as a major source of model structure uncertainty. Previous studies in aquifer remediation design, however, rarely discuss the impact of geological structure uncertainty. This study combines chance-constrained (CC) programming with Bayesian model averaging (BMA) as a BMA-CC framework to assess the impact of geological structure uncertainty in remediation design. To pursue this goal, the BMA-CC method is compared with traditional CC programming that only considers model parameter uncertainty. The BMA-CC method is employed to design a hydraulic barrier to protect public supply wells of the Government St. pump station from salt water intrusion in the "1500-foot" sand and the "1700-foot" sand of the Baton Rouge area, southeastern Louisiana. To address geological structure uncertainty, three groundwater models based on three different hydrostratigraphic architectures are developed. The results show that using traditional CC programming overestimates design reliability. The results also show that at least five additional connector wells are needed to achieve more than 90% design reliability level. The total amount of injected water from the connector wells is higher than the total pumpage of the protected public supply wells. While reducing the injection rate can be achieved by reducing the reliability level, the study finds that the hydraulic barrier design to protect the Government St. pump station may not be economically attractive. © 2014, National Ground Water Association.

Understanding Evolutionary Change within the Framework of Geological Time

ERIC Educational Resources Information Center

Dodick, Jeff

2007-01-01

This paper focuses on a learning strategy designed to overcome students' difficulty in understanding evolutionary change within the framework of geological time. Incorporated into the learning program "From Dinosaurs to Darwin: Evolution from the Perspective of Time," this strategy consists of four scaffolded investigations in which…

Geologic Cross Section E-E' through the Appalachian Basin from the Findlay Arch, Wood County, Ohio, to the Valley and Ridge Province, Pendleton County, West Virginia

USGS Publications Warehouse

Ryder, Robert T.; Swezey, Christopher S.; Crangle, Robert D.; Trippi, Michael H.

2008-01-01

Geologic cross section E-E' is the first in a series of cross sections planned by the U.S. Geological Survey (USGS) to document and improve understanding of the geologic framework and petroleum systems of the Appalachian basin. Cross section E-E' provides a regional view of the structural and stratigraphic framework of the basin from the Findlay arch in northwestern Ohio to the Valley and Ridge province in eastern West Virginia, a distance of approximately 380 miles (mi) (fig. 1, on sheet 1). Cross section E-E' updates earlier geologic cross sections through the central Appalachian basin by Renfro and Feray (1970), Bennison (1978), and Bally and Snelson (1980) and a stratigraphic cross section by Colton (1970). Although other published cross sections through parts of the basin show more structural detail (for example, Shumaker, 1985; Kulander and Dean, 1986) and stratigraphic detail (for example, Ryder, 1992; de Witt and others, 1993; Hettinger, 2001), these other cross sections are of more limited extent geographically and stratigraphically. Although specific petroleum systems in the Appalachian basin are not identified on the cross section, many of their key elements (such as source rocks, reservoir rocks, seals, and traps) can be inferred from lithologic units, unconformities, and geologic structures shown on the cross section. Other aspects of petroleum systems (such as the timing of petroleum generation and preferred migration pathways) may be evaluated by burial history, thermal history, and fluid flow models based on information shown on the cross section. Cross section E-E' lacks the detail to illustrate key elements of coal systems (such as paleoclimate, coal quality, and coal rank), but it does provide a general framework (stratigraphic units and general rock types) for the coal-bearing section. Also, cross section E-E' may be used as a reconnaissance tool to identify plausible geologic structures and strata for the subsurface storage of liquid waste (for example, Colton, 1961; Lloyd and Reid, 1990) or for the sequestration of carbon dioxide (for example, Smith and others, 2002; Lucier and others, 2006).

Updating the Framework Geology of Padre Island National Seashore: Validation of Geophysical Surveys through Sediment Cores

NASA Astrophysics Data System (ADS)

Tuttle, L. F., II; Wernette, P. A.; Houser, C.

2016-12-01

Framework geology has been demonstrated to influence the geomorphology and affect the response of barrier islands to extreme storm events. Therefore, it is vital that we understand the framework geology before we can accurately assess the vulnerability and resiliency of the coast. Geophysical surveys consisting of ground-penetrating radar (GPR) and electromagnetic inductance (EMI) were collected along the length of Padre Island National Seashore (PAIS) to map subsurface infilled paleochannels identified in previous research. The most extensive published survey of PAIS framework geology was conducted in the 1950s as part of dredging the Intracoastal Waterway through Laguna Madre. Using cores and seismic surveys the previous study identified a series of relict infilled paleochannels in dissecting PAIS. The sediment cores presented in our poster were collected in Fall 2016 with a Geoprobe 6712DT. Cores were stored and processed using an X-ray fluorescence (XRF) scanner at the International Ocean Discovery Program repository in College Station, Texas. The XRF data was used to examine mineralogical differences that provide valuable insight into the evolutionary history of the island. This poster presents results from sediment cores collected to validate the geophysical survey data. The broader purpose of this research is to validate the subsurface framework geology features (i.e. infilled paleochannels) in order to more accurately predict future changes to the environmental and economic longevity of PAIS.

Assessment of Undiscovered Technically Recoverable Oil and Gas Resources of the Bakken Formation, Williston Basin, Montana and North Dakota, 2008

USGS Publications Warehouse

Pollastro, R.M.; Roberts, L.N.R.; Cook, T.A.; Lewan, M.D.

2008-01-01

The U.S. Geological Survey (USGS) has completed an assessment of the undiscovered oil and associated gas resources of the Upper Devonian to Lower Mississippian Bakken Formation in the U.S. portion of the Williston Basin of Montana and North Dakota and within the Williston Basin Province. The assessment is based on geologic elements of a total petroleum system (TPS), which include (1) source-rock distribution, thickness, organic richness, maturation, petroleum generation, and migration; (2) reservoir-rock type (conventional or continuous), distribution, and quality; and (3) character of traps and time of formation with respect to petroleum generation and migration. Framework studies in stratigraphy and structural geology and modeling of petroleum geochemistry, combined with historical exploration and production analyses, were used to estimate the undiscovered, technically recoverable oil resource of the Bakken Formation. Using this framework, the USGS defined a Bakken-Lodgepole TPS and seven assessment units (AU) within the system. For the Bakken Formation, the undiscovered oil and associated gas resources were quantitatively estimated for six of these AUs.

A HIERARCHICAL MODELING FRAMEWORK FOR GEOLOGICAL STORAGE OF CARBON DIOXIDE

EPA Science Inventory

Carbon Capture and Storage, or CCS, is likely to be an important technology in a carbonconstrained world. CCS will involve subsurface injection of massive amounts of captured CO₂, on a scale that has not previously been approached. The unprecedented scale of t...

Persistent shoreline shape induced from offshore geologic framework: Effects of shoreface connected ridges

USGS Publications Warehouse

Safak, Ilgar; List, Jeffrey; Warner, John C.; Schwab, William C.

2017-01-01

Mechanisms relating offshore geologic framework to shoreline evolution are determined through geologic investigations, oceanographic deployments, and numerical modeling. Analysis of shoreline positions from the past 50 years along Fire Island, New York, a 50 km long barrier island, demonstrates a persistent undulating shape along the western half of the island. The shelf offshore of these persistent undulations is characterized with shoreface-connected sand ridges (SFCR) of a similar alongshore length scale, leading to a hypothesis that the ridges control the shoreline shape through the modification of flow. To evaluate this, a hydrodynamic model was configured to start with the US East Coast and scale down to resolve the Fire Island nearshore. The model was validated using observations along western Fire Island and buoy data, and used to compute waves, currents and sediment fluxes. To isolate the influence of the SFCR on the generation of the persistent shoreline shape, simulations were performed with a linearized nearshore bathymetry to remove alongshore transport gradients associated with shoreline shape. The model accurately predicts the scale and variation of the alongshore transport that would generate the persistent shoreline undulations. In one location, however, the ridge crest connects to the nearshore and leads to an offshore-directed transport that produces a difference in the shoreline shape. This qualitatively supports the hypothesized effect of cross-shore fluxes on coastal evolution. Alongshore flows in the nearshore during a representative storm are driven by wave breaking, vortex force, advection and pressure gradient, all of which are affected by the SFCR.

Shear wave prediction using committee fuzzy model constrained by lithofacies, Zagros basin, SW Iran

NASA Astrophysics Data System (ADS)

Shiroodi, Sadjad Kazem; Ghafoori, Mohammad; Ansari, Hamid Reza; Lashkaripour, Golamreza; Ghanadian, Mostafa

2017-02-01

The main purpose of this study is to introduce the geological controlling factors in improving an intelligence-based model to estimate shear wave velocity from seismic attributes. The proposed method includes three main steps in the framework of geological events in a complex sedimentary succession located in the Persian Gulf. First, the best attributes were selected from extracted seismic data. Second, these attributes were transformed into shear wave velocity using fuzzy inference systems (FIS) such as Sugeno's fuzzy inference (SFIS), adaptive neuro-fuzzy inference (ANFIS) and optimized fuzzy inference (OFIS). Finally, a committee fuzzy machine (CFM) based on bat-inspired algorithm (BA) optimization was applied to combine previous predictions into an enhanced solution. In order to show the geological effect on improving the prediction, the main classes of predominate lithofacies in the reservoir of interest including shale, sand, and carbonate were selected and then the proposed algorithm was performed with and without lithofacies constraint. The results showed a good agreement between real and predicted shear wave velocity in the lithofacies-based model compared to the model without lithofacies especially in sand and carbonate.

Implications and concerns of deep-seated disposal of hydrocarbon exploration produced water using three-dimensional contaminant transport model in Bhit Area, Dadu District of Southern Pakistan.

PubMed

Ahmad, Zulfiqar; Akhter, Gulraiz; Ashraf, Arshad; Fryar, Alan

2010-11-01

A three-dimensional contaminant transport model has been developed to simulate and monitor the migration of disposal of hydrocarbon exploration produced water in Injection well at 2,100 m depth in the Upper Cretaceous Pab sandstone, Bhit area in Dadu district of Southern Pakistan. The regional stratigraphic and structural geological framework of the area, landform characteristics, meteorological parameters, and hydrogeological milieu have been used in the model to generate the initial simulation of steady-state flow condition in the underlying aquifer's layers. The geometry of the shallow and deep-seated characteristics of the geological formations was obtained from the drilling data, electrical resistivity sounding surveys, and geophysical well-logging information. The modeling process comprised of steady-state simulation and transient simulation of the prolific groundwater system of contamination transport after 1, 10, 30 years of injection. The contaminant transport was evaluated from the bottom of the injection well, and its short- and long-term effects were determined on aquifer system lying in varying hydrogeological and geological conditions.

Variational Bayesian Inversion of Quasi-Localized Seismic Attributes for the Spatial Distribution of Geological Facies

NASA Astrophysics Data System (ADS)

Nawaz, Muhammad Atif; Curtis, Andrew

2018-04-01

We introduce a new Bayesian inversion method that estimates the spatial distribution of geological facies from attributes of seismic data, by showing how the usual probabilistic inverse problem can be solved using an optimization framework still providing full probabilistic results. Our mathematical model consists of seismic attributes as observed data, which are assumed to have been generated by the geological facies. The method infers the post-inversion (posterior) probability density of the facies plus some other unknown model parameters, from the seismic attributes and geological prior information. Most previous research in this domain is based on the localized likelihoods assumption, whereby the seismic attributes at a location are assumed to depend on the facies only at that location. Such an assumption is unrealistic because of imperfect seismic data acquisition and processing, and fundamental limitations of seismic imaging methods. In this paper, we relax this assumption: we allow probabilistic dependence between seismic attributes at a location and the facies in any neighbourhood of that location through a spatial filter. We term such likelihoods quasi-localized.

A reporting protocol for thermochronologic modeling illustrated with data from the Grand Canyon

NASA Astrophysics Data System (ADS)

Flowers, Rebecca M.; Farley, Kenneth A.; Ketcham, Richard A.

2015-12-01

Apatite (U-Th)/He and fission-track dates, as well as 4He/3He and fission-track length data, provide rich thermal history information. However, numerous choices and assumptions are required on the long road from raw data and observations to potentially complex geologic interpretations. This paper outlines a conceptual framework for this path, with the aim of promoting a broader understanding of how thermochronologic conclusions are derived. The tiered structure consists of thermal history model inputs at Level 1, thermal history model outputs at Level 2, and geologic interpretations at Level 3. Because inverse thermal history modeling is at the heart of converting thermochronologic data to interpretation, for others to evaluate and reproduce conclusions derived from thermochronologic results it is necessary to publish all data required for modeling, report all model inputs, and clearly and completely depict model outputs. Here we suggest a generalized template for a model input table with which to arrange, report and explain the choice of inputs to thermal history models. Model inputs include the thermochronologic data, additional geologic information, and system- and model-specific parameters. As an example we show how the origin of discrepant thermochronologic interpretations in the Grand Canyon can be better understood by using this disciplined approach.

Preliminary Gravity and Ground Magnetic Data in the Arbuckle Uplift near Sulphur, Oklahoma

USGS Publications Warehouse

Scheirer, Daniel S.; Aboud, Essam

2008-01-01

Improving knowledge of the geology and geophysics of the Arbuckle Uplift in south-central Oklahoma is a goal of the Framework Geology of Mid-Continent Carbonate Aquifers project sponsored by the United States Geological Survey (USGS) National Cooperative Geologic Mapping Program (NCGMP). In May 2007, we collected ground magnetic and gravity observations in the Hunton Anticline region of the Arbuckle Uplift, near Sulphur, Oklahoma. These observations complement prior gravity data collected for a project sponsored by the National Park Service and helicopter electromagnetic (HEM) and aeromagnetic data collected in March 2007 for the NCGMP project. This report describes the instrumentation and processing that was utilized in the May 2007 geophysical fieldwork, and it presents preliminary results as gravity anomaly maps and magnetic anomaly profiles. Digital tables of gravity and magnetic observations are provided as a supplement to this report. Future work will generate interpretive models of these anomalies and will involve joint analysis of these ground geophysical measurements with airborne and other geophysical and geological observations, with the goal of understanding the geological structures influencing the hydrologic properties of the Arbuckle-Simpson aquifer.

Groundwater flow pattern and related environmental phenomena in complex geologic setting based on integrated model construction

NASA Astrophysics Data System (ADS)

Tóth, Ádám; Havril, Tímea; Simon, Szilvia; Galsa, Attila; Monteiro Santos, Fernando A.; Müller, Imre; Mádl-Szőnyi, Judit

2016-08-01

Groundwater flow, driven, controlled and determined by topography, geology and climate, is responsible for several natural surface manifestations and affected by anthropogenic processes. Therefore, flowing groundwater can be regarded as an environmental agent. Numerical simulation of groundwater flow could reveal the flow pattern and explain the observed features. In complex geologic framework, where the geologic-hydrogeologic knowledge is limited, the groundwater flow model could not be constructed based solely on borehole data, but geophysical information could aid the model building. The integrated model construction was presented via the case study of the Tihany Peninsula, Hungary, with the aims of understanding the background and occurrence of groundwater-related environmental phenomena, such as wetlands, surface water-groundwater interaction, slope instability, and revealing the potential effect of anthropogenic activity and climate change. The hydrogeologic model was prepared on the basis of the compiled archive geophysical database and the results of recently performed geophysical measurements complemented with geologic-hydrogeologic data. Derivation of different electrostratigraphic units, revealing fracturing and detecting tectonic elements was achieved by systematically combined electromagnetic geophysical methods. The deduced information can be used as model input for groundwater flow simulation concerning hydrostratigraphy, geometry and boundary conditions. The results of numerical modelling were interpreted on the basis of gravity-driven regional groundwater flow concept and validated by field mapping of groundwater-related phenomena. The 3D model clarified the hydraulic behaviour of the formations, revealed the subsurface hydraulic connection between groundwater and wetlands and displayed the groundwater discharge pattern, as well. The position of wetlands, their vegetation type, discharge features and induced landslides were explained as environmental imprints of groundwater. The highly vulnerable wetlands and groundwater-dependent ecosystems have to be in the focus of water management and natural conservation policy.

Advances in Geologic Disposal System Modeling and Application to Crystalline Rock

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mariner, Paul E.; Stein, Emily R.; Frederick, Jennifer M.

The Used Fuel Disposition Campaign (UFDC) of the U.S. Department of Energy (DOE) Office of Nuclear Energy (NE), Office of Fuel Cycle Technology (OFCT) is conducting research and development (R&D) on geologic disposal of used nuclear fuel (UNF) and high-level nuclear waste (HLW). Two of the high priorities for UFDC disposal R&D are design concept development and disposal system modeling (DOE 2011). These priorities are directly addressed in the UFDC Generic Disposal Systems Analysis (GDSA) work package, which is charged with developing a disposal system modeling and analysis capability for evaluating disposal system performance for nuclear waste in geologic mediamore » (e.g., salt, granite, clay, and deep borehole disposal). This report describes specific GDSA activities in fiscal year 2016 (FY 2016) toward the development of the enhanced disposal system modeling and analysis capability for geologic disposal of nuclear waste. The GDSA framework employs the PFLOTRAN thermal-hydrologic-chemical multi-physics code and the Dakota uncertainty sampling and propagation code. Each code is designed for massively-parallel processing in a high-performance computing (HPC) environment. Multi-physics representations in PFLOTRAN are used to simulate various coupled processes including heat flow, fluid flow, waste dissolution, radionuclide release, radionuclide decay and ingrowth, precipitation and dissolution of secondary phases, and radionuclide transport through engineered barriers and natural geologic barriers to the biosphere. Dakota is used to generate sets of representative realizations and to analyze parameter sensitivity.« less

Geologic and hydrogeologic framework of the Espa?ola basin -- Proceedings of the 5th annual Espa?ola basin workshop, Santa Fe, New Mexico, March 7-8, 2006

USGS Publications Warehouse

McKinney, Kevin C.

2006-01-01

This report presents abstracts of technical studies that are focused on the hydrogeologic framework of the Espa?ola basin, a major subbasin of the Cenozoic Rio Grande rift. The Rio Grande, Rio Chama, Santa Fe River, and their tributaries carry important surface water in the Espa?ola basin. Sediments and interbedded volcanic rocks fill the Espa?ola basin and form extensive aquifer systems for ground water. Surface and ground water provide the principal sources of water for most residents of the basin, including people in the cities of Santa Fe, Espa?ola, and Los Alamos as well as Native Americans in several Pueblos. The abstracts describe results of technical studies that were presented either as poster exhibits or oral presentations at the fifth-annual Espa?ola basin workshop, held March 7-8 of 2006 in Santa Fe, New Mexico. The principal goal of this workshop was to share information about ongoing studies. The Espa?ola basin workshop was hosted by the Espa?ola basin technical advisory group (EBTAG) and sponsored by the U.S. Geological Survey, the New Mexico Bureau of Geology and Mineral Resources, and the Water Research Technical Assistance Office of Los Alamos National Laboratory. Abstracts in this report have been grouped into six information themes: Basic Water Data, Water Quality and Water Chemistry, Water Balance and Stream/Aquifer Interaction, Data Integration and Hydrologic Model Testing, Three-Dimensional Hydrogeological Architecture, and Geologic Framework. Abstracts submitted by U.S. Geological Survey authors in this report have had their technical content peer reviewed before they were included in the report. Technical reviews were not required for abstracts submitted by authors outside the USGS, although most did receive peer reviews within their originating agencies. Taken together, the abstracts in this report provide a view of the current status of hydrogeologic research within the Espa?ola basin.

A three-dimensional numerical model of predevelopment conditions in the Death Valley regional ground-water flow system, Nevada and California

USGS Publications Warehouse

D'Agnese, Frank A.; O'Brien, G. M.; Faunt, C.C.; Belcher, W.R.; San Juan, C.

2002-01-01

In the early 1990's, two numerical models of the Death Valley regional ground-water flow system were developed by the U.S. Department of Energy. In general, the two models were based on the same basic hydrogeologic data set. In 1998, the U.S. Department of Energy requested that the U.S. Geological Survey develop and maintain a ground-water flow model of the Death Valley region in support of U.S. Department of Energy programs at the Nevada Test Site. The purpose of developing this 'second-generation' regional model was to enhance the knowledge an understanding of the ground-water flow system as new information and tools are developed. The U.S. Geological Survey also was encouraged by the U.S. Department of Energy to cooperate to the fullest extent with other Federal, State, and local entities in the region to take advantage of the benefits of their knowledge and expertise. The short-term objective of the Death Valley regional ground-water flow system project was to develop a steady-state representation of the predevelopment conditions of the ground-water flow system utilizing the two geologic interpretations used to develop the previous numerical models. The long-term objective of this project was to construct and calibrate a transient model that simulates the ground-water conditions of the study area over the historical record that utilizes a newly interpreted hydrogeologic conceptual model. This report describes the result of the predevelopment steady-state model construction and calibration. The Death Valley regional ground-water flow system is situated within the southern Great Basin, a subprovince of the Basin and Range physiographic province, bounded by latitudes 35 degrees north and 38 degrees 15 minutes north and by longitudes 115 and 118 degrees west. Hydrology in the region is a result of both the arid climatic conditions and the complex geology. Ground-water flow generally can be described as dominated by interbasinal flow and may be conceptualized as having two main components: a series of relatively shallow and localized flow paths that are superimposed on deeper regional flow paths. A significant component of the regional ground-water flow is through a thick Paleozoic carbonate rock sequence. Throughout the flow system, ground water flows through zones of high transmissivity that have resulted from regional faulting and fracturing. The conceptual model of the Death Valley regional ground-water flow system used for this study is adapted from the two previous ground-water modeling studies. The three-dimensional digital hydrogeologic framework model developed for the region also contains elements of both of the hydrogeologic framework models used in the previous investigations. As dictated by project scope, very little reinterpretation and refinement were made where these two framework models disagree; therefore, limitations in the hydrogeologic representation of the flow system exist. Despite limitations, the framework model provides the best representation to date of the hydrogeologic units and structures that control regional ground-water flow and serves as an important information source used to construct and calibrate the predevelopment, steady-state flow model. In addition to the hydrogeologic framework, a complex array of mechanisms accounts for flow into, through, and out of the regional ground-water flow system. Natural discharges from the regional ground-water flow system occur by evapotranspiration, springs, and subsurface outflow. In this study, evapotranspiration rates were adapted from a related investigation that developed maps of evapotranspiration areas and computed rates from micrometeorological data collected within the local area over a multiyear period. In some cases, historical spring flow records were used to derive ground-water discharge rates for isolated regional springs. For this investigation, a process-based, numerical model was developed to estimat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Keefer, Donald A.; Shaffer, Eric G.; Storsved, Brynne

A free software application, RVA, has been developed as a plugin to the US DOE-funded ParaView visualization package, to provide support in the visualization and analysis of complex reservoirs being managed using multi-fluid EOR techniques. RVA, for Reservoir Visualization and Analysis, was developed as an open-source plugin to the 64 bit Windows version of ParaView 3.14. RVA was developed at the University of Illinois at Urbana-Champaign, with contributions from the Illinois State Geological Survey, Department of Computer Science and National Center for Supercomputing Applications. RVA was designed to utilize and enhance the state-of-the-art visualization capabilities within ParaView, readily allowing jointmore » visualization of geologic framework and reservoir fluid simulation model results. Particular emphasis was placed on enabling visualization and analysis of simulation results highlighting multiple fluid phases, multiple properties for each fluid phase (including flow lines), multiple geologic models and multiple time steps. Additional advanced functionality was provided through the development of custom code to implement data mining capabilities. The built-in functionality of ParaView provides the capacity to process and visualize data sets ranging from small models on local desktop systems to extremely large models created and stored on remote supercomputers. The RVA plugin that we developed and the associated User Manual provide improved functionality through new software tools, and instruction in the use of ParaView-RVA, targeted to petroleum engineers and geologists in industry and research. The RVA web site (http://rva.cs.illinois.edu) provides an overview of functions, and the development web site (https://github.com/shaffer1/RVA) provides ready access to the source code, compiled binaries, user manual, and a suite of demonstration data sets. Key functionality has been included to support a range of reservoirs visualization and analysis needs, including: sophisticated connectivity analysis, cross sections through simulation results between selected wells, simplified volumetric calculations, global vertical exaggeration adjustments, ingestion of UTChem simulation results, ingestion of Isatis geostatistical framework models, interrogation of joint geologic and reservoir modeling results, joint visualization and analysis of well history files, location-targeted visualization, advanced correlation analysis, visualization of flow paths, and creation of static images and animations highlighting targeted reservoir features.« less

RVA: A Plugin for ParaView 3.14

DOE Office of Scientific and Technical Information (OSTI.GOV)

2015-09-04

RVA is a plugin developed for the 64-bit Windows version of the ParaView 3.14 visualization package. RVA is designed to provide support in the visualization and analysis of complex reservoirs being managed using multi-fluid EOR techniques. RVA, for Reservoir Visualization and Analysis, was developed at the University of Illinois at Urbana-Champaign, with contributions from the Illinois State Geological Survey, Department of Computer Science and National Center for Supercomputing Applications. RVA was designed to utilize and enhance the state-of-the-art visualization capabilities within ParaView, readily allowing joint visualization of geologic framework and reservoir fluid simulation model results. Particular emphasis was placed onmore » enabling visualization and analysis of simulation results highlighting multiple fluid phases, multiple properties for each fluid phase (including flow lines), multiple geologic models and multiple time steps. Additional advanced functionality was provided through the development of custom code to implement data mining capabilities. The built-in functionality of ParaView provides the capacity to process and visualize data sets ranging from small models on local desktop systems to extremely large models created and stored on remote supercomputers. The RVA plugin that we developed and the associated User Manual provide improved functionality through new software tools, and instruction in the use of ParaView-RVA, targeted to petroleum engineers and geologists in industry and research. The RVA web site (http://rva.cs.illinois.edu) provides an overview of functions, and the development web site (https://github.com/shaffer1/RVA) provides ready access to the source code, compiled binaries, user manual, and a suite of demonstration data sets. Key functionality has been included to support a range of reservoirs visualization and analysis needs, including: sophisticated connectivity analysis, cross sections through simulation results between selected wells, simplified volumetric calculations, global vertical exaggeration adjustments, ingestion of UTChem simulation results, ingestion of Isatis geostatistical framework models, interrogation of joint geologic and reservoir modeling results, joint visualization and analysis of well history files, location-targeted visualization, advanced correlation analysis, visualization of flow paths, and creation of static images and animations highlighting targeted reservoir features.« less

Canada in 3D - Toward a Sustainable 3D Model for Canadian Geology from Diverse Data Sources

NASA Astrophysics Data System (ADS)

Brodaric, B.; Pilkington, M.; Snyder, D. B.; St-Onge, M. R.; Russell, H.

2015-12-01

Many big science issues span large areas and require data from multiple heterogeneous sources, for example climate change, resource management, and hazard mitigation. Solutions to these issues can significantly benefit from access to a consistent and integrated geological model that would serve as a framework. However, such a model is absent for most large countries including Canada, due to the size of the landmass and the fragmentation of the source data into institutional and disciplinary silos. To overcome these barriers, the "Canada in 3D" (C3D) pilot project was recently launched by the Geological Survey of Canada. C3D is designed to be evergreen, multi-resolution, and inter-disciplinary: (a) it is to be updated regularly upon acquisition of new data; (b) portions vary in resolution and will initially consist of four layers (surficial, sedimentary, crystalline, and mantle) with intermediary patches of higher-resolution fill; and (c) a variety of independently managed data sources are providing inputs, such as geophysical, 3D and 2D geological models, drill logs, and others. Notably, scalability concerns dictate a decentralized and interoperable approach, such that only key control objects, denoting anchors for the modeling process, are imported into the C3D database while retaining provenance links to original sources. The resultant model is managed in the database, contains full modeling provenance as well as links to detailed information on rock units, and is to be visualized in desktop and online environments. It is anticipated that C3D will become the authoritative state of knowledge for the geology of Canada at a national scale.

Framework for the assessment of interaction between CO2 geological storage and other sedimentary basin resources.

PubMed

Michael, K; Whittaker, S; Varma, S; Bekele, E; Langhi, L; Hodgkinson, J; Harris, B

2016-02-01

Sedimentary basins around the world considered suitable for carbon storage usually contain other natural resources such as petroleum, coal, geothermal energy and groundwater. Storing carbon dioxide in geological formations in the basins adds to the competition for access to the subsurface and the use of pore space where other resource-based industries also operate. Managing potential impacts that industrial-scale injection of carbon dioxide may have on other resource development must be focused to prevent potential conflicts and enhance synergies where possible. Such a sustainable coexistence of various resource developments can be accomplished by implementing a Framework for Basin Resource Management strategy (FBRM). The FBRM strategy utilizes the concept of an Area of Review (AOR) for guiding development and regulation of CO2 geological storage projects and for assessing their potential impact on other resources. The AOR is determined by the expected physical distribution of the CO2 plume in the subsurface and the modelled extent of reservoir pressure increase resulting from the injection of the CO2. This information is used to define the region to be characterised and monitored for a CO2 injection project. The geological characterisation and risk- and performance-based monitoring will be most comprehensive within the region of the reservoir containing the carbon dioxide plume and should consider geological features and wells continuously above the plume through to its surface projection; this region defines where increases in reservoir pressure will be greatest and where potential for unplanned migration of carbon dioxide is highest. Beyond the expanse of the carbon dioxide plume, geological characterisation and monitoring should focus only on identified features that could be a potential migration conduit for either formation water or carbon dioxide.

A spatial econometric analysis of land-use change with land cover trends data: an application to the Pacific Northwest

Treesearch

David J. Lewis; Ralph J. Alig

2014-01-01

This paper develops a plot-level spatial econometric land-use model and estimates it with U.S. Geological Survey Land Cover Trends (LCT) geographic information system panel data for the western halves of the states of Oregon and Washington. The discrete-choice framework we use models plot-scale choices of the three dominant land uses in this region: forest, agriculture...

A conceptual hydrogeologic model for the hydrogeologic framework, geochemistry, and groundwater-flow system of the Edwards-Trinity and related aquifers in the Pecos County region, Texas

USGS Publications Warehouse

Thomas, Jonathan V.; Stanton, Gregory P.; Bumgarner, Johnathan R.; Pearson, Daniel K.; Teeple, Andrew; Houston, Natalie A.; Payne, Jason; Musgrove, MaryLynn

2013-01-01

Several previous studies have been done to compile or collect physical and chemical data, describe the hydrogeologic processes, and develop conceptual and numerical groundwater-flow models of the Edwards-Trinity aquifer in the Trans-Pecos region. Documented methods were used to compile and collect groundwater, surface-water, geochemical, geophysical, and geologic information that subsequently were used to develop this conceptual model.

From spatially variable streamflow to distributed hydrological models: Analysis of key modeling decisions

NASA Astrophysics Data System (ADS)

Fenicia, Fabrizio; Kavetski, Dmitri; Savenije, Hubert H. G.; Pfister, Laurent

2016-02-01

This paper explores the development and application of distributed hydrological models, focusing on the key decisions of how to discretize the landscape, which model structures to use in each landscape element, and how to link model parameters across multiple landscape elements. The case study considers the Attert catchment in Luxembourg—a 300 km2 mesoscale catchment with 10 nested subcatchments that exhibit clearly different streamflow dynamics. The research questions are investigated using conceptual models applied at hydrologic response unit (HRU) scales (1-4 HRUs) on 6 hourly time steps. Multiple model structures are hypothesized and implemented using the SUPERFLEX framework. Following calibration, space/time model transferability is tested using a split-sample approach, with evaluation criteria including streamflow prediction error metrics and hydrological signatures. Our results suggest that: (1) models using geology-based HRUs are more robust and capture the spatial variability of streamflow time series and signatures better than models using topography-based HRUs; this finding supports the hypothesis that, in the Attert, geology exerts a stronger control than topography on streamflow generation, (2) streamflow dynamics of different HRUs can be represented using distinct and remarkably simple model structures, which can be interpreted in terms of the perceived dominant hydrologic processes in each geology type, and (3) the same maximum root zone storage can be used across the three dominant geological units with no loss in model transferability; this finding suggests that the partitioning of water between streamflow and evaporation in the study area is largely independent of geology and can be used to improve model parsimony. The modeling methodology introduced in this study is general and can be used to advance our broader understanding and prediction of hydrological behavior, including the landscape characteristics that control hydrologic response, the dominant processes associated with different landscape types, and the spatial relations of catchment processes. This article was corrected on 14 MAR 2016. See the end of the full text for details.

Combined constraints on the structure and physical properties of the East Antarctic lithosphere from geology and geophysics.

NASA Astrophysics Data System (ADS)

Reading, A. M.; Staal, T.; Halpin, J.; Whittaker, J. M.; Morse, P. E.

2017-12-01

The lithosphere of East Antarctica is one of the least explored regions of the planet, yet it is gaining in importance in global scientific research. Continental heat flux density and 3D glacial isostatic adjustment studies, for example, rely on a good knowledge of the deep structure in constraining model inputs.In this contribution, we use a multidisciplinary approach to constrain lithospheric domains. To seismic tomography models, we add constraints from magnetic studies and also new geological constraints. Geological knowledge exists around the periphery of East Antarctica and is reinforced in the knowledge of plate tectonic reconstructions. The subglacial geology of the Antarctic hinterland is largely unknown but the plate reconstructions allow the well-posed extrapolation of major terranes into the interior of the continent, guided by the seismic tomography and magnetic images. We find that the northern boundary of the lithospheric domain centred on the Gamburtsev Subglacial Mountains has a possible trend that runs south of the Lambert Glacier region, turning coastward through Wilkes Land. Other periphery-to-interior connections are less well constrained and the possibility of lithospheric domains that are entirely sub-glacial is high. We develop this framework to include a probabilistic method of handling alternate models and quantifiable uncertainties. We also show first results in using a Bayesian approach to predicting lithospheric boundaries from multivariate data.Within the newly constrained domains, we constrain heat flux (density) as the sum of basal heat flux and upper crustal heat flux. The basal heat flux is constrained by geophysical methods while the upper crustal heat flux is constrained by geology or predicted geology. In addition to heat flux constraints, we also consider the variations in friction experienced by moving ice sheets due to varying geology.

Mississippi River delta plain, Louisiana coast, and inner shelf Holocene geologic framework, processes, and resources

USGS Publications Warehouse

Williams, S. Jeffress; Kulp, Mark; Penland, Shea; Kindinger, Jack L.; Flocks, James G.; Buster, Noreen A.; Holmes, Charles W.

2009-01-01

Extending nearly 400 km from Sabine Pass on the Texas-Louisiana border east to the Chandeleur Islands, the Louisiana coastal zone (Fig. 11.1) along the north-central Gulf of Mexico is the southern terminus of the largest drainage basin in North America (>3.3 million km2), which includes the Mississippi River delta plain where approximately 6.2 million kilograms per year of sediment is delivered to the Gulf of Mexico (Coleman 1988). The Mississippi River, active since at least Late Jurassic time (Mann and Thomas 1968), is the main distributary channel of this drainage system and during the Holocene has constructed one of the largest delta plains in the world, larger than 30,000 km2 (Coleman and Prior 1980; Coleman 1981; Coleman et al. 1998). The subsurface geology and geomorphology of the Louisiana coastal zone reffects a complex history of regional tectonic events and fluvial, deltaic, and marine sedimentary processes affected by large sea-level fluctuations. Despite the complex geology of the north-central Gulf basin, a long history of engineering studies and Scientific research investigations (see table 11.1) has led to substantial knowledge of the geologic framework and evolution of the delta plain region (see also Bird et al., chapter 1 in this volume). Mississippi River delta plain, Louisiana coast, and inner shelf Holocene geologic framework, processes, and resources. Available from: https://www.researchgate.net/publication/262802561_Mississippi_River_delta_plain_Louisiana_coast_and_inner_shelf_Holocene_geologic_framework_processes_and_resources [accessed Sep 13, 2017].

Mapping Electrical Structures in the Jarud Basin, Northeast China through Magnetotelluric Sounding

NASA Astrophysics Data System (ADS)

Zhao, W.

2015-12-01

In recent years, China Geological Survey (CGS) has launched 3D geological mapping programs from regional to local scales. The project Deep geological survey at the periphery of the Songliao Basin funded by CGS was implemented from 2012 to 2014. Its main goals are to reveal the tectonic framework of the Jarud Basin (JB) as well as to identify the strata distribution of Permian Linxi Formation by integrating new electromagnetic data with existing geophysical and geological data since black mudstones in the Linxi Formation have shown the potential of shale gas. The study area covered dominantly with Cretaceous-Jurassic igneous rocks with exception of the southeast part is situated in Jarud Banner and Ar Horqin Banner, Inner Mongolia, China. It tectonically lies in the southern Great Khingan Range, western margin of the Songliao Basin, and north of Xar Moron Fault. Over the period of 2012 to 2014, a magnetotelluric survey was carried out at the JB. A total of 926 MT sites with nominal spacing 1 km was acquired in the effective frequency range of 0.01 Hz ~ 300 Hz on six NW and five NE profiles, covering area that exceeds 10, 000 km2. After dimensionality analysis and static shift removal, the nonlinear conjugate algorithm was used to conduct 2D inversion for TM and TE modes. The resistivity models underwent examination using sensitivity tests. The optimal resistivity models revealed numerous large faults, some of which constitute the boundaries of the JB, and modified the tectonic framework. Integrated with well logging and geological mapping data, the strata of Linxi Formation were identified and classified into three depressions: Depressions Arituguri, Gadasu and Wufen. Attention should be paid to Depression Gadasu with area of around 500 km2 since it contains reasonably thick conductive sediments exceeding 4 km in depth which are inferred to be black mudstones pertaining to shale gas.

Contribution of in situ geophysical methods for the definition of the São Sebastião crater model (Azores)

NASA Astrophysics Data System (ADS)

Lopes, Isabel; Deidda, Gian Piero; Mendes, Manuela; Strobbia, Claudio; Santos, Jaime

2013-11-01

The area located inside the São Sebastião volcanic crater, at the southeast end of Terceira Island (Azores), is characterized by an important amplification of ground motion with respect to the surrounding area, as clearly demonstrated by the spatial distribution of the damage that occurred during the Terceira earthquake (the strongest earthquake felt in the Island during the recent decades - 01/01/1980 - M = 7.2). Geological and geophysical studies have been conducted, to characterize the volcanic crater and understand the different site effects that occurred in the village of São Sebastião. The complexity of the subsurface geology, with intercalations of compact basalt and soft pyroclastic deposits, is associated to extreme vertical and lateral velocity contrasts, and poses a serious challenge to different geophysical characterization methods. The available qualitative model did not allow a complete understanding of the site effects. A new seismic campaign has been designed and acquired, and a single, geologically consistent geophysical model has been generated integrating the existing and new data. The new campaign included two cross-line P-wave seismic refraction profiles, four short SH-wave seismic reflection profiles, and seven multichannel surface wave acquisitions. The integration and joint interpretation of geophysical and geological data allowed mutual validation and confirmation of data processing steps. In particular, the use of refraction, reflection and surface wave techniques allowed facing the complexity of a geology that can pose different challenges to all the methods when used individually: velocity inversions, limited reflectivity, and lateral variations. It is shown how the integration of seismic data from different methods, in the framework of a geological model, allowed the geometrical and dynamic characterization of the site. Correlation with further borehole information, then allowed the definition of a subsoil model for the crater, providing information that allowed a better understanding of the earthquake site effects in the São Sebastião village. The new near-surface geological model includes a lava layer within the soft infill materials of the crater. This new model matches closely with the damage distribution map, and explains the spatial variation of building stock performance in the 1980 earthquake.

A multiagency and multijurisdictional approach to mapping the glacial deposits of the Great Lakes region in three dimensions

USGS Publications Warehouse

Berg, Richard C.; Brown, Steven E.; Thomason, Jason F.; Hasenmueller, Nancy R.; Letsinger, Sally L.; Kincare, Kevin A.; Esch, John M.; Kehew, Alan E.; Thorleifson, L. Harvey; Kozlowski, Andrew L.; Bird, Brian C.; Pavey, Richard R.; Bajc, Andy F.; Burt, Abigail K.; Fleeger, Gary M.; Carson, Eric C.

2016-01-01

The Great Lakes Geologic Mapping Coalition (GLGMC), consisting of state geological surveys from all eight Great Lakes states, the Ontario Geological Survey, and the U.S. Geological Survey, was conceived out of a societal need for unbiased and scientifically defensible geologic information on the shallow subsurface, particularly the delineation, interpretation, and viability of groundwater resources. Only a small percentage (<10%) of the region had been mapped in the subsurface, and there was recognition that no single agency had the financial, intellectual, or physical resources to conduct such a massive geologic mapping effort at a detailed scale over a wide jurisdiction. The GLGMC provides a strategy for generating financial and stakeholder support for three-dimensional (3-D) geologic mapping, pooling of physical and personnel resources, and sharing of mapping and technological expertise to characterize the thick cover of glacial sediments. Since its inception in 1997, the GLGMC partners have conducted detailed surficial and 3-D geologic mapping within all jurisdictions, and concurrent significant scientific advancements have been made to increase understanding of the history and framework of geologic processes. More importantly, scientific information has been provided to public policymakers in understandable formats, emphasis has been placed on training early-career scientists in new mapping techniques and emerging technologies, and a successful model has been developed of state/provincial and federal collaboration focused on geologic mapping, as evidenced by this program's unprecedented and long-term successful experiment of 10 geological surveys working together to address common issues.

Appalachian basin oil and natural gas: stratigraphic framework, total petroleum systems, and estimated ultimate recovery: Chapter C.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ryder, Robert T.; Milici, Robert C.; Swezey, Christopher S.; Trippi, Michael H.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The most recent U.S. Geological Survey (USGS) assessment of undiscovered oil and gas resources of the Appalachian basin was completed in 2002 (Milici and others, 2003). This assessment was based on the total petroleum system (TPS), a concept introduced by Magoon and Dow (1994) and developed during subsequent studies such as those by the U.S. Geological Survey World Energy Assessment Team (2000) and by Biteau and others (2003a,b). Each TPS is based on specific geologic elements that include source rocks, traps and seals, reservoir rocks, and the generation and migration of hydrocarbons. This chapter identifies the TPSs defined in the 2002 Appalachian basin oil and gas assessment and places them in the context of the stratigraphic framework associated with regional geologic cross sections D–D′ (Ryder and others, 2009, which was re-released in this volume, chap. E.4.1) and E–E′ (Ryder and others, 2008, which was re-released in this volume, chap. E.4.2). Furthermore, the chapter presents a recent estimate of the ultimate recoverable oil and natural gas in the basin.

Geochemistry and the Understanding of Groundwater Systems

NASA Astrophysics Data System (ADS)

Glynn, P. D.; Plummer, L. N.; Weissmann, G. S.; Stute, M.

2009-12-01

Geochemical techniques and concepts have made major contributions to the understanding of groundwater systems. Advances continue to be made through (1) development of measurement and characterization techniques, (2) improvements in computer technology, networks and numerical modeling, (3) investigation of coupled geologic, hydrologic, geochemical and biologic processes, and (4) scaling of individual observations, processes or subsystem models into larger coherent model frameworks. Many applications benefit from progress in these areas, such as: (1) understanding paleoenvironments, in particular paleoclimate, through the use of groundwater archives, (2) assessing the sustainability (recharge and depletion) of groundwater resources, and (3) their vulnerability to contamination, (4) evaluating the capacity and consequences of subsurface waste isolation (e.g. geologic carbon sequestration, nuclear and chemical waste disposal), (5) assessing the potential for mitigation/transformation of anthropogenic contaminants in groundwater systems, and (6) understanding the effect of groundwater lag times in ecosystem-scale responses to natural events, land-use changes, human impacts, and remediation efforts. Obtaining “representative” groundwater samples is difficult and progress in obtaining “representative” samples, or interpreting them, requires new techniques in characterizing groundwater system heterogeneity. Better characterization and simulation of groundwater system heterogeneity (both physical and geochemical) is critical to interpreting the meaning of groundwater “ages”; to understanding and predicting groundwater flow, solute transport, and geochemical evolution; and to quantifying groundwater recharge and discharge processes. Research advances will also come from greater use and progress (1) in the application of environmental tracers to ground water dating and in the analysis of new geochemical tracers (e.g. compound specific isotopic analyses, noble gas isotopes, analyses of natural organic tracers), (2) in inverse geochemical and hydrological modeling, (3) in the understanding and simulation of coupled biological, geological, geochemical and hydrological processes, and (4) in the description and quantification of processes occurring at the boundaries of groundwater systems (e.g. unsaturated zone processes, groundwater/surface water interactions, impacts of changing geomorphology and vegetation). Improvements are needed in the integration of widely diverse information. Better techniques are needed to construct coherent conceptual frameworks from individual observations, simulated or reconstructed information, process models, and intermediate scale models. Iterating between data collection, interpretation, and the application of forward, inverse, and statistical modeling tools is likely to provide progress in this area. Quantifying groundwater system processes by using an open-system thermodynamic approach in a common mass- and energy-flow framework will also facilitate comparison and understanding of diverse processes.

Geologic and Geophysical Framework of the Santa Rosa 7.5' Quadrangle, Sonoma County, California

USGS Publications Warehouse

McLaughlin, R.J.; Langenheim, V.E.; Sarna-Wojcicki, A. M.; Fleck, R.J.; McPhee, D.K.; Roberts, C.W.; McCabe, C.A.; Wan, Elmira

2008-01-01

The geologic and geophysical maps of Santa Rosa 7.5? quadrangle and accompanying structure sections portray the sedimentary and volcanic stratigraphy and crustal structure of the Santa Rosa 7.5? quadrangle and provide a context for interpreting the evolution of volcanism and active faulting in this region. The quadrangle is located in the California Coast Ranges north of San Francisco Bay and is traversed by the active Rodgers Creek, Healdsburg and Maacama Fault Zones. The geologic and geophysical data presented in this report, are substantial improvements over previous geologic and geophysical maps of the Santa Rosa area, allowing us to address important geologic issues. First, the geologic mapping is integrated with gravity and magnetic data, allowing us to depict the thicknesses of Cenozoic deposits, the depth and configuration of the Mesozoic basement surface, and the geometry of fault structures beneath this region to depths of several kilometers. This information has important implications for constraining the geometries of major active faults and for understanding and predicting the distribution and intensity of damage from ground shaking during earthquakes. Secondly, the geologic map and the accompanying description of the area describe in detail the distribution, geometry and complexity of faulting associated with the Rodgers Creek, Healdsburg and Bennett Valley Fault Zones and associated faults in the Santa Rosa quadrangle. The timing of fault movements is constrained by new 40Ar/39Ar ages and tephrochronologic correlations. These new data provide a better understanding of the stratigraphy of the extensive sedimentary and volcanic cover in the area and, in particular, clarify the formational affinities of Pliocene and Pleistocene nonmarine sedimentary units in the map area. Thirdly, the geophysics, particularly gravity data, indicate the locations of thick sections of sedimentary and volcanic fill within ground water basins of the Santa Rosa plain and Rincon, Bennett, and northwestern Sonoma Valleys, providing geohydrologists a more realistic framework for groundwater flow models.

Geological maps and models: are we certain how uncertain they are?

NASA Astrophysics Data System (ADS)

Mathers, Steve; Waters, Colin; McEvoy, Fiona

2014-05-01

Geological maps and latterly 3D models provide the spatial framework for geology at diverse scales or resolutions. As demands continue to rise for sustainable use of the subsurface, use of these maps and models is informing decisions on management of natural resources, hazards and environmental change. Inaccuracies and uncertainties in geological maps and models can impact substantially on the perception, assessment and management of opportunities and the associated risks . Lithostratigraphical classification schemes predominate, and are used in most geological mapping and modelling. The definition of unit boundaries, as 2D lines or 3D surfaces is the prime objective. The intervening area or volume is rarely described other than by its bulk attributes, those relating to the whole unit. Where sufficient data exist on the spatial and/or statistical distribution of properties it can be gridded or voxelated with integrity. Here we only discuss the uncertainty involved in defining the boundary conditions. The primary uncertainty of any geological map or model is the accuracy of the geological boundaries, i.e. tops, bases, limits, fault intersections etc. Traditionally these have been depicted on BGS maps using three line styles that reflect the uncertainty of the boundary, e.g. observed, inferred, conjectural. Most geological maps tend to neglect the subsurface expression (subcrops etc). Models could also be built with subsurface geological boundaries (as digital node strings) tagged with levels of uncertainty; initial experience suggests three levels may again be practicable. Once tagged these values could be used to autogenerate uncertainty plots. Whilst maps are predominantly explicit and based upon evidence and the conceptual the understanding of the geologist, models of this type are less common and tend to be restricted to certain software methodologies. Many modelling packages are implicit, being driven by simple statistical interpolation or complex algorithms for building surfaces in ways that are invisible and so not controlled by the working geologist. Such models have the advantage of being replicable within a software package and so can discount some interpretational differences between modellers. They can however create geologically implausible results unless good geological rules and control are established prior to model calculation. Comparisons of results from varied software packages yield surprisingly diverse results. This is a significant and often overlooked source of uncertainty in models. Expert elicitation is commonly employed to establish values used in statistical treatments of model uncertainty. However this introduces another possible source of uncertainty created by the different judgements of the modellers. The pragmatic solution appears to be using panels of experienced geologists to elicit the values. Treatments of uncertainty in maps and models yield relative rather than absolute values even though many of these are expressed numerically. This makes it extremely difficult to devise standard methodologies to determine uncertainty or propose fixed numerical scales for expressing the results. Furthermore, these may give a misleading impression of greater certainty than actually exists. This contribution outlines general perceptions with regard to uncertainty in our maps and models and presents results from recent BGS studies

U.S. Geological Survey: A synopsis of Three-dimensional Modeling

USGS Publications Warehouse

Jacobsen, Linda J.; Glynn, Pierre D.; Phelps, Geoff A.; Orndorff, Randall C.; Bawden, Gerald W.; Grauch, V.J.S.

2011-01-01

The U.S. Geological Survey (USGS) is a multidisciplinary agency that provides assessments of natural resources (geological, hydrological, biological), the disturbances that affect those resources, and the disturbances that affect the built environment, natural landscapes, and human society. Until now, USGS map products have been generated and distributed primarily as 2-D maps, occasionally providing cross sections or overlays, but rarely allowing the ability to characterize and understand 3-D systems, how they change over time (4-D), and how they interact. And yet, technological advances in monitoring natural resources and the environment, the ever-increasing diversity of information needed for holistic assessments, and the intrinsic 3-D/4-D nature of the information obtained increases our need to generate, verify, analyze, interpret, confirm, store, and distribute its scientific information and products using 3-D/4-D visualization, analysis, modeling tools, and information frameworks. Today, USGS scientists use 3-D/4-D tools to (1) visualize and interpret geological information, (2) verify the data, and (3) verify their interpretations and models. 3-D/4-D visualization can be a powerful quality control tool in the analysis of large, multidimensional data sets. USGS scientists use 3-D/4-D technology for 3-D surface (i.e., 2.5-D) visualization as well as for 3-D volumetric analyses. Examples of geological mapping in 3-D include characterization of the subsurface for resource assessments, such as aquifer characterization in the central United States, and for input into process models, such as seismic hazards in the western United States.

Bedrock geologic map of the Nashua South quadrangle, Hillsborough County, New Hampshire, and Middlesex County, Massachusetts

USGS Publications Warehouse

Walsh, Gregory J.; Jahns, Richard H.; Aleinikoff, John N.

2013-01-01

The bedrock geology of the 7.5-minute Nashua South quadrangle consists primarily of deformed Silurian metasedimentary rocks of the Berwick Formation. The metasedimentary rocks are intruded by a Late Silurian to Early Devonian diorite-gabbro suite, Devonian rocks of the Ayer Granodiorite, Devonian granitic rocks of the New Hampshire Plutonic Suite including pegmatite and the Chelmsford Granite, and Jurassic diabase dikes. The bedrock geology was mapped to study the tectonic history of the area and to provide a framework for ongoing hydrogeologic characterization of the fractured bedrock of Massachusetts and New Hampshire. This report presents mapping by G.J. Walsh and R.H. Jahns and zircon U-Pb geochronology by J.N. Aleinikoff. The complete report consists of a map, text pamphlet, and GIS database. The map and text pamphlet are only available as downloadable files (see frame at right). The GIS database is available for download in ESRITM shapefile and Google EarthTM formats, and includes contacts of bedrock geologic units, faults, outcrops, structural geologic information, photographs, and a three-dimensional model.

Geologic interpretation and multibeam bathymetry of the sea floor in southeastern Long Island Sound

USGS Publications Warehouse

Poppe, Lawrence J.; Ackerman, Seth D.; Doran, Elizabeth F.; Moser, Marc S.; Stewart, Helen F.; Forfinski, Nicholas A.; Gardner, Uther L.; Keene, Jennifer A.

2006-01-01

Digital terrain models (DTMs) produced from multibeam echosounder (MBES) bathymetric data provide valuable base maps for marine geological interpretations (e.g. Todd and others, 1999; Mosher and Thomson, 2002; ten Brink and others, 2004; Poppe and others, 2006a,b). These maps help define the geological variability of the sea floor (one of the primary controls of benthic habitat diversity); improve our understanding of the processes that control the distribution and transport of bottom sediments, the distribution of benthic habitats and associated infaunal community structures; and provide a detailed framework for future research, monitoring, and management activities. The bathymetric survey interpreted herein (National Oceanic and Atmospheric Administration (NOAA) survey H11255) covers roughly 95 km? of sea floor in southeastern Long Island Sound (fig. 1). This bathymetry has been examined in relation to seismic reflection data collected concurrently, as well as archived seismic profiles acquired as part of a long-standing geologic mapping partnership between the State of Connecticut and the U.S. Geological Survey (USGS). The objective of this work was to use these geophysical data sets to interpret geomorphological attributes of the sea floor in terms of the Quaternary geologic history and modern sedimentary processes within Long Island Sound.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ernest A. Mancini

The University of Alabama in cooperation with Texas A&M University, McGill University, Longleaf Energy Group, Strago Petroleum Corporation, and Paramount Petroleum Company are undertaking an integrated, interdisciplinary geoscientific and engineering research project. The project is designed to characterize and model reservoir architecture, pore systems and rock-fluid interactions at the pore to field scale in Upper Jurassic Smackover reef and carbonate shoal reservoirs associated with varying degrees of relief on pre-Mesozoic basement paleohighs in the northeastern Gulf of Mexico. The project effort includes the prediction of fluid flow in carbonate reservoirs through reservoir simulation modeling that utilizes geologic reservoir characterization andmore » modeling and the prediction of carbonate reservoir architecture, heterogeneity and quality through seismic imaging. The primary objective of the project is to increase the profitability, producibility and efficiency of recovery of oil from existing and undiscovered Upper Jurassic fields characterized by reef and carbonate shoals associated with pre-Mesozoic basement paleohighs. The principal research effort for Year 3 of the project has been reservoir characterization, 3-D modeling, testing of the geologic-engineering model, and technology transfer. This effort has included six tasks: (1) the study of seismic attributes, (2) petrophysical characterization, (3) data integration, (4) the building of the geologic-engineering model, (5) the testing of the geologic-engineering model and (6) technology transfer. This work was scheduled for completion in Year 3. Progress on the project is as follows: geoscientific reservoir characterization is completed. The architecture, porosity types and heterogeneity of the reef and shoal reservoirs at Appleton and Vocation Fields have been characterized using geological and geophysical data. The study of rock-fluid interactions has been completed. Observations regarding the diagenetic processes influencing pore system development and heterogeneity in these reef and shoal reservoirs have been made. Petrophysical and engineering property characterization has been completed. Porosity and permeability data at Appleton and Vocation Fields have been analyzed, and well performance analysis has been conducted. Data integration is up to date, in that, the geological, geophysical, petrophysical and engineering data collected to date for Appleton and Vocation Fields have been compiled into a fieldwide digital database. 3-D geologic modeling of the structures and reservoirs at Appleton and Vocation Fields has been completed. The models represent an integration of geological, petrophysical and seismic data. 3-D reservoir simulation of the reservoirs at Appleton and Vocation Fields has been completed. The 3-D geologic models served as the framework for the simulations. The geologic-engineering models of the Appleton and Vocation Field reservoirs have been developed. These models are being tested. The geophysical interpretation for the paleotopographic feature being tested has been made, and the study of the data resulting from drilling of a well on this paleohigh is in progress. Numerous presentations on reservoir characterization and modeling at Appleton and Vocation Fields have been made at professional meetings and conferences and a short course on microbial reservoir characterization and modeling based on these fields has been prepared.« less

Quaternary Geologic Framework of the St. Clair River between Michigan and Ontario, Canada

USGS Publications Warehouse

Foster, David S.; Denny, Jane F.

2009-01-01

Concern about the effect of geomorphic changes in the St. Clair River on water levels in the Upper Great Lakes resulted in the need for information on the geologic framework of the river. A geophysical survey of the Upper St. Clair River between Port Huron, MI, and Sarnia, Ontario, Canada, was conducted to determine the Quaternary geologic framework of the region. Previously available and new sediment samples and photographic and video data support the interpretation of the seismic stratigraphy and surficial geology. Three seismic stratigraphic units and two unconformities were identified. Glacial drift, consisting of interbedded till and glaciolacustrine deposits, overlies shale. Glaciofluvial and modern fluvial processes have eroded the glacial drift. Glaciofluvial, glaciolacustrine, fluvial, and lacustrine deposits overlie this unconformity. Seismic facies were interpreted to identify areas where these geologic facies exist; however, in the absence of distinct boundaries between facies, these deposits were mapped as one undifferentiated unit. This unit is thickest in the northernmost 3 kilometers of the river, where it consists of relatively coarse-grained fluvial, reworked glaciofluvial, and possibly glaciofluvial deposits. To the south, this coarse-grained unit thins or is absent. The undifferentiated unit comprises most of the surficial deposits in the northernmost river area. Some areas of glacial drift, predominantly till, are exposed at the lake and riverbed. The shale is not exposed anywhere in the region. Geophysical surveys at sites downriver, together with the results of previous studies, indicate that the geologic framework is similar to that in the northernmost river area except for the absence or reduced thickness of the coarse-grained fluvial deposits. Instead, glacial drift is exposed at the riverbed or is covered by a veneer of sediment. This information on the substrate is important for ongoing sediment transport studies.

A modular approach to addressing model design, scale, and parameter estimation issues in distributed hydrological modelling

USGS Publications Warehouse

Leavesley, G.H.; Markstrom, S.L.; Restrepo, Pedro J.; Viger, R.J.

2002-01-01

A modular approach to model design and construction provides a flexible framework in which to focus the multidisciplinary research and operational efforts needed to facilitate the development, selection, and application of the most robust distributed modelling methods. A variety of modular approaches have been developed, but with little consideration for compatibility among systems and concepts. Several systems are proprietary, limiting any user interaction. The US Geological Survey modular modelling system (MMS) is a modular modelling framework that uses an open source software approach to enable all members of the scientific community to address collaboratively the many complex issues associated with the design, development, and application of distributed hydrological and environmental models. Implementation of a common modular concept is not a trivial task. However, it brings the resources of a larger community to bear on the problems of distributed modelling, provides a framework in which to compare alternative modelling approaches objectively, and provides a means of sharing the latest modelling advances. The concepts and components of the MMS are described and an example application of the MMS, in a decision-support system context, is presented to demonstrate current system capabilities. Copyright ?? 2002 John Wiley and Sons, Ltd.

The effects of the Chesapeake Bay impact crater on the geologic framework and the correlation of hydrogeologic units of southeastern Virginia, south of the James River

USGS Publications Warehouse

Powars, David S.

2000-01-01

About 35 million years ago, a large comet or meteor slammed into the shallow shelf on the western margin of the Atlantic Ocean, creating the Chesapeake Bay impact crater. This report, the second in a series, refines the geologic framework of southeastern Virginia, south of the James River in and near the impact crater, and presents evidence for the existence of a pre-impact James River structural zone. The report includes detailed correlations of core lithologies with borehole geophysical logs; the correlations provide the foundation for the compilation of stratigraphic cross sections. These cross sections are tied into the geologic framework of the lower York-James Peninsula as presented in the first report in the series, Professional Paper 1612

A unified framework for modelling sediment fate from source to sink and its interactions with reef systems over geological times.

PubMed

Salles, Tristan; Ding, Xuesong; Webster, Jody M; Vila-Concejo, Ana; Brocard, Gilles; Pall, Jodie

2018-03-27

Understanding the effects of climatic variability on sediment dynamics is hindered by limited ability of current models to simulate long-term evolution of sediment transfer from source to sink and associated morphological changes. We present a new approach based on a reduced-complexity model which computes over geological time: sediment transport from landmasses to coasts, reworking of marine sediments by longshore currents, and development of coral reef systems. Our framework links together the main sedimentary processes driving mixed siliciclastic-carbonate system dynamics. It offers a methodology for objective and quantitative sediment fate estimations over regional and millennial time-scales. A simulation of the Holocene evolution of the Great Barrier Reef shows: (1) how high sediment loads from catchments erosion prevented coral growth during the early transgression phase and favoured sediment gravity-flows in the deepest parts of the northern region basin floor (prior to 8 ka before present (BP)); (2) how the fine balance between climate, sea-level, and margin physiography enabled coral reefs to thrive under limited shelf sedimentation rates after ~6 ka BP; and, (3) how since 3 ka BP, with the decrease of accommodation space, reduced of vertical growth led to the lateral extension of reefs consistent with available observational data.

NONFUEL MINERAL RESOURCES OF THE PACIFIC EXCLUSIVE ECONOMIC ZONE.

USGS Publications Warehouse

Clague, David; Bischoff, James; Howell, David

1984-01-01

The Pacific Exclusive Economic Zone contains a variety of hard mineral resources. Sand and gravel and their associated placer deposits of heavy minerals are the most likely to be developed in the near future, but offshore and deep water deposits of phosphorite, abyssal manganese nodules, ferromanganese crusts enriched in cobalt, and massive sulfide deposits all represent future resources. The distribution, extent, and formation of these deposits are poorly understood and will be clarified only with additional exploration, framework geologic mapping, and study of the processes by which these resources form. It is pointed out that the initial discovery of most hard-mineral resources in the EEZ was made during routine scientific marine-geologic surveys aimed at understanding the framework geology and geologic processes of an offshore region.

Evaluation of undergraduate geologists' problem solving and cognition during field exams using a mixed methods approach

NASA Astrophysics Data System (ADS)

Balliet, Russell N.

Understanding how geologists conduct fieldwork through analysis of problem solving has significant potential impact on field instruction methods. Recent progress has been made in this area but the problem solving behaviors displayed by geologists during fieldwork and the associated underlying cognition remains poorly understood. We present research showing how geology students initiate and develop geologic models as part of the problem solving process. We qualitatively analyzed field notes and interview data from 36 undergraduate geoscientists engaged in field exams while enrolled in a six-week advanced field camp. Eight cognitive frameworks grouped in two broad categories emerged from the data that show how students develop geologic models. Students employ both single and multiple model approaches with varying degrees of success and frequency. The success of any given approach is dependent on the level of students' geologic situational awareness. The development of multiple geologic models leads to a higher rate of success in general, because of the inherent flexibility to accommodate newly collected data. Instructors should continue to teach a multiple model approach until students have the proper geologic skills to ensure a high level of situational awareness and exhibit expert characteristics in the field. In addition, we collected GPS navigation data from students during these field exams in order to understand the relationship between navigation, cognition, and performance. From the analysis of this data we found that over half of all stops are 1-4 minutes long, while very few of students' stops are longer than 9 minutes as the frequency of stops decreases as the duration increases. Regardless of performance or framework, there is an increase in shorter stops and decrease in longer stops from exam one to three, indicating that students changed the way they investigated as the field course progressed. Temporal signatures categorized by performance only show slight differences, but do indicate that there is an increase in very short and longer stops with declining performance. In contrast, higher performance is linked to an increase in short and medium length stops, suggesting that stops 4-14 minutes long are a "sweet spot" for investigation. We speculate that a high percentage of very short stops involve basic field tasks such as locating or data collection and that the decreasing frequency of long stops indicates that there is a relationship between the length of the stop and the complexity of the activities performed during that stop. Students increased experience leads to more efficient stops as they become more competent with field tasks and more versed in the regional geology. The GPS data we collected from these students while they took these notes allowing us to connect the duration of a stop to the types of notes produced during that stop. Note taking species occurred in various frequencies with the most common type being those that focused on lithologic, or lithologic & structural data collection. Stops that produced geologic models, specifically structural models, were much less frequent. The more frequent data collection stops are very short in length (typically 1-4 minutes), while the more complex stops tend to be longer in duration as the note taking gets more complex. Poor performing students had a high proportion of stops where they only collect lithologic data or stops where they don't generate any hypotheses. In contrast, successful students have more structural data and hypothesis generation in their notes. From this analysis we conclude that too much effort spent on stops with only basic data collection leaves less time for the cognitive effort required for model development, eventually leading to poor exam performance. Specifically, a higher frequency of lithologic data stops and lack of structural data leads to the development of incomplete geologic models or lack of comprehensive models altogether. Field instructors often educate their students on good note taking practices and critique the content of their students' field notebooks, and these findings can inform the content of that critique. Students' utilize many different problem solving approaches in the field, but we suggest that instructors continue to advocate a multiple model approach until students are capable of using a single model approach. In this approach students should decrease the number of geologic models they are using as the day progresses to avoid overwhelming themselves with data and hypothesis. Furthermore, field instructors need to work with students on developing their geologic investigation skills further and improving their efficiency. Specifically students need to collect a higher proportion of structural data and develop complete geologic models earlier in the day. (Abstract shortened by UMI.)

Modeling dolomitized carbonate-ramp reservoirs: A case study of the Seminole San Andres unit. Part 2 -- Seismic modeling, reservoir geostatistics, and reservoir simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, F.P.; Dai, J.; Kerans, C.

1998-11-01

In part 1 of this paper, the authors discussed the rock-fabric/petrophysical classes for dolomitized carbonate-ramp rocks, the effects of rock fabric and pore type on petrophysical properties, petrophysical models for analyzing wireline logs, the critical scales for defining geologic framework, and 3-D geologic modeling. Part 2 focuses on geophysical and engineering characterizations, including seismic modeling, reservoir geostatistics, stochastic modeling, and reservoir simulation. Synthetic seismograms of 30 to 200 Hz were generated to study the level of seismic resolution required to capture the high-frequency geologic features in dolomitized carbonate-ramp reservoirs. Outcrop data were collected to investigate effects of sampling interval andmore » scale-up of block size on geostatistical parameters. Semivariogram analysis of outcrop data showed that the sill of log permeability decreases and the correlation length increases with an increase of horizontal block size. Permeability models were generated using conventional linear interpolation, stochastic realizations without stratigraphic constraints, and stochastic realizations with stratigraphic constraints. Simulations of a fine-scale Lawyer Canyon outcrop model were used to study the factors affecting waterflooding performance. Simulation results show that waterflooding performance depends strongly on the geometry and stacking pattern of the rock-fabric units and on the location of production and injection wells.« less

U.S. Geological Survey core science systems strategy: characterizing, synthesizing, and understanding the critical zone through a modular science framework

USGS Publications Warehouse

Bristol, R. Sky; Euliss, Ned H.; Booth, Nathaniel L.; Burkardt, Nina; Diffendorfer, Jay E.; Gesch, Dean B.; McCallum, Brian E.; Miller, David M.; Morman, Suzette A.; Poore, Barbara S.; Signell, Richard P.; Viger, Roland J.

2013-01-01

Core Science Systems is a new mission of the U.S. Geological Survey (USGS) that resulted from the 2007 Science Strategy, "Facing Tomorrow's Challenges: U.S. Geological Survey Science in the Decade 2007-2017." This report describes the Core Science Systems vision and outlines a strategy to facilitate integrated characterization and understanding of the complex Earth system. The vision and suggested actions are bold and far-reaching, describing a conceptual model and framework to enhance the ability of the USGS to bring its core strengths to bear on pressing societal problems through data integration and scientific synthesis across the breadth of science. The context of this report is inspired by a direction set forth in the 2007 Science Strategy. Specifically, ecosystem-based approaches provide the underpinnings for essentially all science themes that define the USGS. Every point on Earth falls within a specific ecosystem where data, other information assets, and the expertise of USGS and its many partners can be employed to quantitatively understand how that ecosystem functions and how it responds to natural and anthropogenic disturbances. Every benefit society obtains from the planet-food, water, raw materials to build infrastructure, homes and automobiles, fuel to heat homes and cities, and many others, are derived from or affect ecosystems. The vision for Core Science Systems builds on core strengths of the USGS in characterizing and understanding complex Earth and biological systems through research, modeling, mapping, and the production of high quality data on the Nation's natural resource infrastructure. Together, these research activities provide a foundation for ecosystem-based approaches through geologic mapping, topographic mapping, and biodiversity mapping. The vision describes a framework founded on these core mapping strengths that makes it easier for USGS scientists to discover critical information, share and publish results, and identify potential collaborations that transcend all USGS missions. The framework is designed to improve the efficiency of scientific work within USGS by establishing a means to preserve and recall data for future applications, organizing existing scientific knowledge and data to facilitate new use of older information, and establishing a future workflow that naturally integrates new data, applications, and other science products to make interdisciplinary research easier and more efficient. Given the increasing need for integrated data and interdisciplinary approaches to solve modern problems, leadership by the Core Science Systems mission will facilitate problem solving by all USGS missions in ways not formerly possible. The report lays out a strategy to achieve this vision through three goals with accompanying objectives and actions. The first goal builds on and enhances the strengths of the Core Science Systems mission in characterizing and understanding the Earth system from the geologic framework to the topographic characteristics of the land surface and biodiversity across the Nation. The second goal enhances and develops new strengths in computer and information science to make it easier for USGS scientists to discover data and models, share and publish results, and discover connections between scientific information and knowledge. The third goal brings additional focus to research and development methods to address complex issues affecting society that require integration of knowledge and new methods for synthesizing scientific information. Collectively, the report lays out a strategy to create a seamless connection between all USGS activities to accelerate and make USGS science more efficient by fully integrating disciplinary expertise within a new and evolving science paradigm for a changing world in the 21st century.

Quantifying Risks and Uncertainties Associated with Induced Seismicity due to CO2 Injection into Geologic Formations with Faults

NASA Astrophysics Data System (ADS)

Hou, Z.; Nguyen, B. N.; Bacon, D. H.; White, M. D.; Murray, C. J.

2016-12-01

A multiphase flow and reactive transport simulator named STOMP-CO2-R has been developed and coupled to the ABAQUS® finite element package for geomechanical analysis enabling comprehensive thermo-hydro-geochemical-mechanical (THMC) analyses. The coupled THMC simulator has been applied to analyze faulted CO2 reservoir responses (e.g., stress and strain distributions, pressure buildup, slip tendency factor, pressure margin to fracture) with various complexities in fault and reservoir structures and mineralogy. Depending on the geological and reaction network settings, long-term injection of CO2 can have a significant effect on the elastic stiffness and permeability of formation rocks. In parallel, an uncertainty quantification framework (UQ-CO2), which consists of entropy-based prior uncertainty representation, efficient sampling, geostatistical reservoir modeling, and effective response surface analysis, has been developed for quantifying risks and uncertainties associated with CO2 sequestration. It has been demonstrated for evaluating risks in CO2 leakage through natural pathways and wellbores, and for developing predictive reduced order models. Recently, a parallel STOMP-CO2-R has been developed and the updated STOMP/ABAQUS model has been proven to have a great scalability, which makes it possible to integrate the model with the UQ framework to effectively and efficiently explore multidimensional parameter space (e.g., permeability, elastic modulus, crack orientation, fault friction coefficient) for a more systematic analysis of induced seismicity risks.

Modeling Geomagnetic Variations using a Machine Learning Framework

NASA Astrophysics Data System (ADS)

Cheung, C. M. M.; Handmer, C.; Kosar, B.; Gerules, G.; Poduval, B.; Mackintosh, G.; Munoz-Jaramillo, A.; Bobra, M.; Hernandez, T.; McGranaghan, R. M.

2017-12-01

We present a framework for data-driven modeling of Heliophysics time series data. The Solar Terrestrial Interaction Neural net Generator (STING) is an open source python module built on top of state-of-the-art statistical learning frameworks (traditional machine learning methods as well as deep learning). To showcase the capability of STING, we deploy it for the problem of predicting the temporal variation of geomagnetic fields. The data used includes solar wind measurements from the OMNI database and geomagnetic field data taken by magnetometers at US Geological Survey observatories. We examine the predictive capability of different machine learning techniques (recurrent neural networks, support vector machines) for a range of forecasting times (minutes to 12 hours). STING is designed to be extensible to other types of data. We show how STING can be used on large sets of data from different sensors/observatories and adapted to tackle other problems in Heliophysics.

Global continental and ocean basin reconstructions since 200 Ma

NASA Astrophysics Data System (ADS)

Seton, M.; Müller, R. D.; Zahirovic, S.; Gaina, C.; Torsvik, T.; Shephard, G.; Talsma, A.; Gurnis, M.; Turner, M.; Maus, S.; Chandler, M.

2012-07-01

Global plate motion models provide a spatial and temporal framework for geological data and have been effective tools for exploring processes occurring at the earth's surface. However, published models either have insufficient temporal coverage or fail to treat tectonic plates in a self-consistent manner. They usually consider the motions of selected features attached to tectonic plates, such as continents, but generally do not explicitly account for the continuous evolution of plate boundaries through time. In order to explore the coupling between the surface and mantle, plate models are required that extend over at least a few hundred million years and treat plates as dynamic features with dynamically evolving plate boundaries. We have constructed a new type of global plate motion model consisting of a set of continuously-closing topological plate polygons with associated plate boundaries and plate velocities since the break-up of the supercontinent Pangea. Our model is underpinned by plate motions derived from reconstructing the seafloor-spreading history of the ocean basins and motions of the continents and utilizes a hybrid absolute reference frame, based on a moving hotspot model for the last 100 Ma, and a true-polar wander corrected paleomagnetic model for 200 to 100 Ma. Detailed regional geological and geophysical observations constrain plate boundary inception or cessation, and time-dependent geometry. Although our plate model is primarily designed as a reference model for a new generation of geodynamic studies by providing the surface boundary conditions for the deep earth, it is also useful for studies in disparate fields when a framework is needed for analyzing and interpreting spatio-temporal data.

A new model for early Earth: heat-pipe cooling

NASA Astrophysics Data System (ADS)

Webb, A. G.; Moore, W. B.

2013-12-01

In the study of heat transport and lithospheric dynamics of early Earth, current models depend upon plate tectonic and vertical tectonic concepts. Plate tectonic models adequately account for regions with diverse lithologies juxtaposed along ancient shear zones, as seen at the famous Eoarchean Isua supracrustal belt of West Greenland. Vertical tectonic models to date have involved volcanism, sub- and intra-lithospheric diapirism, and sagduction, and can explain the geology of the best-preserved low-grade ancient terranes, such as the Paleoarchean Barberton and Pilbara greenstone belts. However, these models do not offer a globally-complete framework consistent with the geologic record. Plate tectonics models suggest that paired metamorphic belts and passive margins are among the most likely features to be preserved, but the early rock record shows no evidence of these terranes. Existing vertical tectonics models account for the >300 million years of semi-continuous volcanism and diapirism at Barberton and Pilbara, but when they explain the shearing record at Isua, they typically invoke some horizontal motion that cannot be differentiated from plate motion and is not a salient feature of the lengthy Barberton and Pilbara records. Despite the strengths of these models, substantial uncertainty remains about how early Earth evolved from magma ocean to plate tectonics. We have developed a new model, based on numerical simulations and analysis of the geologic record, that provides a coherent, global geodynamic framework for Earth's evolution from magma ocean to subduction tectonics. We hypothesize that heat-pipe cooling offers a viable mechanism for the lithospheric dynamics of early Earth. Our numerical simulations of heat-pipe cooling on early Earth indicate that a cold, thick, single-plate lithosphere developed as a result of frequent volcanic eruptions that advected surface materials downward. The constant resurfacing and downward advection caused compression as the surface rocks were forced radially inward, resulting in uplift, exhumation, and shortening. Declining heat sources over time led to an abrupt, dynamically spontaneous transition to plate tectonics. The model predicts a geological record with rapid, semi-continuous volcanic resurfacing; contractional deformation; a low geothermal gradient across the bulk of the lithosphere; and a rapid decrease in heat-pipe volcanism after the initiation of plate tectonics. Review of data from ancient cratons and the detrital zircon record is consistent with these predictions. In this presentation, we review these findings with a focus on comparison of the model predictions with the geologic record. This comparison suggests that Earth cooled via heat pipes until a ~3.2 Ga subduction initiation episode. The Isua record reflects long-lived contractional deformation, and the Barberton and Pilbara records preserve heat-pipe lithospheric development in regions without significant contraction. In summary, the heat-pipe model provides a view of early Earth that is more globally applicable than existing plate and vertical tectonic models.

Groundwater Pathway Model for the Los Alamos National Laboratory Technical Area 54, Area G, Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stauffer, Philip H.; Chu, Shaoping; Miller, Terry A.

This report consists of four major sections, including this introductory section. Section 2 provides an overview of previous investigations related to the development of the current sitescale model. The methods and data used to develop the 3-D groundwater model and the techniques used to distill that model into a form suitable for use in the GoldSim models are discussed in Section 3. Section 4 presents the results of the model development effort and discusses some of the uncertainties involved. Eight attachments that provide details about the components and data used in this groundwater pathway model are also included with thismore » report. The groundwater modeling effort reported here is a revision of the work that was conducted in 2005 (Stauffer et al., 2005a) in support of the 2008 Area G performance assessment and composite analysis (LANL, 2008). The revision effort was undertaken primarily to incorporate new geologic information that has been collected since 2003 at, and in the vicinity of, Area G. The new data were used to create a more accurate geologic framework model (GFM) that forms the basis of the numerical modeling of the site’s long-term performance. The groundwater modeling uses mean hydrologic properties of the geologic strata underlying Area G; this revision includes an evaluation of the impacts that natural variability in these properties may have on the model projections.« less

Geothermal prospection in the Greater Geneva Basin (Switzerland and France): Integration of geological data in the new Information System

NASA Astrophysics Data System (ADS)

Brentini, Maud; Favre, Stéphanie; Rusillon, Elme; Moscariello, Andrea

2017-04-01

Piloted by the State of Geneva and implemented by the SIG (Services Industriels de Genève), the GEothermie2020 program aims to develop geothermal energy resources in the Greater Geneva Basin (GGB) (Moscariello A., 2016). Since 2014, many existing data have been examined (Rusillon et al., 2017, Clerc et al., 2016) and new ones have been collected. Nevertheless, to date the actual IT infrastructure of the State of Geneva is neither designed to centralize these data, nor to respond efficiently to operational demands. In this context, we are developing a new Information System adapted to this specific situation (Favre et al., 2017). In order to establish a solid base line for future exploration and exploitation of underground natural resources, the centralization of the geological surface/subsurface knowledge is the real challenge. Finding the balance between comprehensiveness and relevance of the data to integrate into this future complete database system is key. Geological data are numerous, of various nature, and often very heterogeneous. Incorporating and relating all individual data is therefore a difficult and challenging task. As a result, a large work has to be done on the understanding and the harmonization of the stratigraphy of the Geneva Basin, to appreciate the data and spatial geological heterogneity. The first step consisted in consulting all data from MSc and PhD work of the University of Geneva (about 50) and from literature concerning the regional geology. In parallel, an overview concerning the subsurface geological data management in Europe carried out to learn from the experience of other geological surveys. Heterogeneities and discrepancies of the data are the main issue. Over several years (since late 30s) individual authors collected different type of data and made different interpretations leading a variety of stratigraphic facies definitions, associations and environmental reconstructions. Cross checking these data with national programs, such as HARMOS (official Swiss stratigraphic framework; Morard, 2014, Strasser et al., 2016) is essential to evaluate this type of harmonization system. The current work is establishing composite logs and a stratigraphic catalog where clear stratigraphic framework for the GGB is defined. This will provide a better understanding of the subsurface and a general framework for the new State database. The GEothermie 2020 Program has raised the importance of harmonizing and correlating data in order to understand better the GGB subsurface geology. The future database will be based on a clear and accurate geological and stratigraphic framework where relevant data will be integrated. It will offer a valuable tool to the State of Geneva and external users to find data easily, generate correlations, subsurface models and extract information with specific inquiries. The development of this intelligent and interactive data management system is pivotal to offer an easier and smart management of subsurface resources to the State. REFERENCES Clerc, N., Rusillon, E., Cardello, L., Moscariello, A. and Renard, P., 2016. Structural Modeling of the Geneva Basin for Geothermal Ressource Assessment. Abstract, 14th Swiss Geoscience Meeting, Geneva, Switzerland. Favre, S., Brentini, M., Giuliani, G. and Lehmann, A., 2017. Geothermal prospection in the Greater Geneva Basin (Switzerland and France): Architecture of the new Information System. Abstract, EGU General Assembly 2017, Vienna, Austria. Morard, A., 2014. Correlations beyond HARMOS: how, where, why? Swiss Geoscience Meeting 2014. Platform Geosciences, Swiss Academy of Science, SCNAT. Conference paper. Moscariello A. 2016: Geothermal exploration in SW Switzerland, Proceeding of the European Geotermal Congress, Strasbourg 19-23 september 2016, 9 pp. Rusillon, E., Clerc, N., Makhloufi, Y., Brentini and M., Moscariello, A., 2017. Geothermal prospection in the Greater Geneva Basin (Switzerland and France): Structural and reservoir quality assessment. Abstract, EGU General Assembly 2017, Vienna, Austria. Strasser, A., Charollais, J., Conrad, M. A., Clavel, B., Pictet, A. and Mastrangelo, B., 2016. The Cretaceous of the Swiss Jura Mountains : an improved lithostratigraphic scheme. Swiss Journal of Geosciences, 1-20.

A 3D object-based model to simulate highly-heterogeneous, coarse, braided river deposits

NASA Astrophysics Data System (ADS)

Huber, E.; Huggenberger, P.; Caers, J.

2016-12-01

There is a critical need in hydrogeological modeling for geologically more realistic representation of the subsurface. Indeed, widely-used representations of the subsurface heterogeneity based on smooth basis functions such as cokriging or the pilot-point approach fail at reproducing the connectivity of high permeable geological structures that control subsurface solute transport. To realistically model the connectivity of high permeable structures of coarse, braided river deposits, multiple-point statistics and object-based models are promising alternatives. We therefore propose a new object-based model that, according to a sedimentological model, mimics the dominant processes of floodplain dynamics. Contrarily to existing models, this object-based model possesses the following properties: (1) it is consistent with field observations (outcrops, ground-penetrating radar data, etc.), (2) it allows different sedimentological dynamics to be modeled that result in different subsurface heterogeneity patterns, (3) it is light in memory and computationally fast, and (4) it can be conditioned to geophysical data. In this model, the main sedimentological elements (scour fills with open-framework-bimodal gravel cross-beds, gravel sheet deposits, open-framework and sand lenses) and their internal structures are described by geometrical objects. Several spatial distributions are proposed that allow to simulate the horizontal position of the objects on the floodplain as well as the net rate of sediment deposition. The model is grid-independent and any vertical section can be computed algebraically. Furthermore, model realizations can serve as training images for multiple-point statistics. The significance of this model is shown by its impact on the subsurface flow distribution that strongly depends on the sedimentological dynamics modeled. The code will be provided as a free and open-source R-package.

Geologic setting of the low-level burial grounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lindsey, K.A.; Jaeger, G.K.; Slate, J.L.

1994-10-13

This report describes the regional and site specific geology of the Hanford Sites low-level burial grounds in the 200 East and West Areas. The report incorporates data from boreholes across the entire 200 Areas, integrating the geology of this area into a single framework. Geologic cross-sections, isopach maps, and structure contour maps of all major geological units from the top of the Columbia River Basalt Group to the surface are included. The physical properties and characteristics of the major suprabasalt sedimentary units also are discussed.

'Cape capture': Geologic data and modeling results suggest the holocene loss of a Carolina Cape

USGS Publications Warehouse

Thieler, E.R.; Ashton, A.D.

2011-01-01

For more than a century, the origin and evolution of the set of cuspate forelands known as the Carolina Capes-Hatteras, Lookout, Fear, and Romain-off the eastern coast of the United States have been discussed and debated. The consensus conceptual model is not only that these capes existed through much or all of the Holocene transgression, but also that their number has not changed. Here we describe bathymetric, lithologic, seismic, and chronologic data that suggest another cape may have existed between Capes Hatteras and Lookout during the early to middle Holocene. This cape likely formed at the distal end of the Neuse-Tar-Pamlico fiuvial system during the early Holocene transgression, when this portion of the shelf was fiooded ca. 9 cal (calibrated) kyr B.P., and was probably abandoned by ca. 4 cal kyr B.P., when the shoreline attained its present general configuration. Previously proposed mechanisms for cape formation suggest that the large-scale, rhythmic pattern of the Carolina Capes arose from a hydrodynamic template or the preexisting geologic framework. Numerical modeling, however, suggests that the number and spacing of capes can be dynamic, and that a coast can self-organize in response to a high-angle-wave instability in shoreline shape. In shoreline evolution model simulations, smaller cuspate forelands are subsumed by larger neighbors over millennial time scales through a process of 'cape capture.' The suggested former cape in Raleigh Bay represents the first interpreted geological evidence of dynamic abandonment suggested by the self-organization hypothesis. Cape capture may be a widespread process in coastal environments with large-scale rhythmic shoreline features; its preservation in the sedimentary record will vary according to geologic setting, physical processes, and sea-level history. ?? 2011 Geological Society of America.

A proposed new framework for valorization of geoheritage in Norway

NASA Astrophysics Data System (ADS)

Dahl, Rolv; Bergengren, Anna; Heldal, Tom

2015-04-01

The geological history of Norway is a complex one, . The exploitation of geological resources of different kinds has always provided the backbone of the Norwegian community. Nevertheless, the perception of geology and the geological processes that created the landscape is little appreciated, compared to bio-diversity and cultural heritage. Some geological localities play an important role in our perception and scientific understanding of the landscape. Other localities are, or could be, important tourist destinations. Other localities can in turn be important for geoscience education on all levels, whereas other plays a major role in the understanding of geodiversity and geoheritage and should be protected as natural monuments. A database based on old registrations has been compiled and a web mapping server is recently launched based on old and new registrations. However, no systematical classification and identification of important sites has been done for the last thirty years. We are now calling for a crowdsourcing process in the geological community in order to validate and valorize the registrations, as well as defining new points and areas of interest. Furthermore, we are developing a valorization system for these localities. The framework for this system is based on studies from inventories in other countries, as well as suggestions from ProGeo. The aim is to raise awareness of important sites, and how they are treated and utilized for scientific, or educational purposes, as tourist destinations or heritage sites. Our presentation will focus on the development of the framework and its implications.

Sublake geologic structure from high-resolution seismic-reflection data from four sinkhole lakes in the Lake Wales Ridge, Central Florida

USGS Publications Warehouse

Tihansky, A.B.; Arthur, J.D.; DeWitt, D.W.

1996-01-01

Seismic-reflection profiles from Lake Wales, Blue Lake, Lake Letta, and Lake Apthorp located along the Lake Wales Ridge in central Florida provide local detail within the regional hydrogeologic framework as described by litho- and hydrostratigraphic cross sections. Lakes located with the mantled karst region have long been considered to be sinkhole lakes, originating from subsidence activity. High-resolution seismic- reflection data confirm this origin for these four lakes. The geologic framework of the Lake Wales Ridge has proven to be a suitable geologic setting for continuous high-resolution seismic-reflection profiling in lakes; however, the nature of the lake-bottom sediments largely controls the quality of the seismic data. In lakes with significant organic-rich bottom deposits, interpretable record was limited to areas where organic deposits were minimal. In lakes with clean, sandy bottoms, the seismic-reflection methods were highly successful in obtaining data that can be correlated with sublake subsidence features. These techniques are useful in examining sublake geology and providing a better understanding of how confining units are affected by subsidence in a region where their continuity is of significant importance to local lake hydrology. Although local geologic control around each lake generally corresponds to the regional geologic framework, local deviations from regional geologic trends occur in sublake areas affected by subsidence activity. Each of the four lakes examined represents a unique set of geologic controls and provides some degree of structural evidence of subsidence activity. Sublake geologic structures identified include: (1) marginal lake sediments dipping into bathymetric lows, (2) lateral discontinuity of confining units including sags and breaches, (3) the disruption and reworking of overlying unconsolidated siliciclastic sediments as they subside into the underlying irregular limestone surface, and (4) sublake regions where confining units appear to remain intact and unaffected by nearby subsidence activity. Each lake likely is underlain by several piping features rather than one large subsidence feature.

Geologic and climatic controls on the radon emanation coefficient

USGS Publications Warehouse

Schumann, R.R.; Gundersen, L.C.S.; ,

1997-01-01

Geologic, pedologic, and climatic factors, including radium content, grain size, siting of radon parents within soil grains or on grain coatings, and soil moisture conditions, determine a soil's emanating power and radon transport characteristics. Data from field studies indicate that soils derived from similar parent rocks in different regions have significantly different emanation coefficients due to the effects of climate on these soil characteristics. An important tool for measuring radon source strength (i.e., radium content) is ground-based and aerial gamma radioactivity measurements. Regional correlations between soil radium content, determined by gamma spectrometry, and soil-gas or indoor radon concentrations can be traced to the influence of climatic and geologic factors on intrinsic permeability and radon emanation coefficients. Data on soil radium content, permeability, and moisture content, when combined with data on emanation coefficients, can form a framework for development of quantitative predictive models for radon generation in rocks and soils.

Airborne electromagnetic data and processing within Leach Lake Basin, Fort Irwin, California: Chapter G in Geology and geophysics applied to groundwater hydrology at Fort Irwin, California

USGS Publications Warehouse

Bedrosian, Paul A.; Ball, Lyndsay B.; Bloss, Benjamin R.; Buesch, David C.

2014-01-01

From December 2010 to January 2011, the U.S. Geological Survey conducted airborne electromagnetic and magnetic surveys of Leach Lake Basin within the National Training Center, Fort Irwin, California. These data were collected to characterize the subsurface and provide information needed to understand and manage groundwater resources within Fort Irwin. A resistivity stratigraphy was developed using ground-based time-domain electromagnetic soundings together with laboratory resistivity measurements on hand samples and borehole geophysical logs from nearby basins. This report releases data associated with the airborne surveys, as well as resistivity cross-sections and depth slices derived from inversion of the airborne electromagnetic data. The resulting resistivity models confirm and add to the geologic framework, constrain the hydrostratigraphy and the depth to basement, and reveal the distribution of faults and folds within the basin.

High-resolution stratigraphy of a Mississippi subdelta-lobe progradation in the Barataria Bight, north-central Gulf of Mexico

USGS Publications Warehouse

Flocks, J.G.; Ferina, N.F.; Dreher, C.; Kindinger, J.L.; FitzGerald, D.M.; Kulp, M.A.

2006-01-01

The coastal zone of southeastern Louisiana is the product of numerous cycles of progradation, abandonment, and marine transgression of the Mississippi River delta. Currently, the shoreline in the Barataria Bight is undergoing significant erosion and retreat, and understanding its evolution is crucial in stabilization efforts. This study uses an extensive collection of geophysical and sediment core data from Barataria Bay and offshore to develop a geologic model of the shallow (< 10 m) subsurface. The purpose of the model is twofold: (1) establish the stratigraphic architecture of a subdelta lobe of the Bayou des Families delta, deposited by the Mississippi River approximately 4000 years before present; and (2) provide a high-resolution description of the geologic framework in a context that can be applied to coastal management issues in similar fluvially dominated coastal environments worldwide. The results of the study demonstrate how high-quality geologic data from the coastal environment can be used not only to further our understanding of shoreline evolution but also to provide pertinent information for coastal management needs.

Geologic framework, structure, and hydrogeologic characteristics of the Knippa Gap area in eastern Uvalde and western Medina Counties, Texas

USGS Publications Warehouse

Clark, Allan K.; Pedraza, Diana E.; Morris, Robert R.

2013-01-01

By using data that were compiled and collected for this study and previous studies, a revised map was constructed depicting the geologic framework, structure, and hydrogeologic characteristics of the Knippa Gap area in eastern Uvalde and western Medina Counties, Tex. The map also shows the interpreted structural dip directions and interpreted location of a structural low (trough) in the area known as the Knippa Gap.

Geologic characterization of shelf areas using usSEABED for GIS mapping, modeling processes and assessing marine sand and gravel resources

USGS Publications Warehouse

Williams, S.J.; Bliss, J.D.; Arsenault, M.A.; Jenkins, C.J.; Goff, J.A.

2007-01-01

Geologic maps depicting offshore sedimentary features serve many scientific and applied purposes. Such maps have been lacking, but recent computer technology and software offer promise in the capture and display of diverse marine data. Continental margins contain landforms which provide a variety of important functions and contain important sedimentary records. Some shelf areas also contain deposits regarded as potential aggregate resources. Because proper management of coastal and offshore areas is increasingly important, knowledge of the framework geology and marine processes is critical. Especially valuable are comprehensive and integrated digital databases based on high-quality information from original sources. Products of interest are GIS maps containing thematic information, such as sediment character and texture. These products are useful to scientists modeling nearshore and shelf processes as well as planners and managers. The U.S. Geological Survey is leading a national program to gather a variety of extant marine geologic data into the usSEABED database system. This provides centralized, integrated marine geologic data collected over the past 50 years. To date, over 340,000 sediment data points from the U.S. reside in usSEABED, which combines an array of physical data and analytical and descriptive information about the sea floor and are available to the marine community through three USGS data reports for the Atlantic, Gulf of Mexico, and Pacific published in 2006, and the project web sites: (http://woodshole.er.usg s.gov/project-pages/aggregates/ and http://walrus.wr.usgs.gov/usseabed/)

SECARB Commercial Scale CO 2 Injection and Optimization of Storage Capacity in the Southeastern United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koperna, George J.; Pashin, Jack; Walsh, Peter

The Commercial Scale Project is a US DOE/NETL funded initiative aimed at enhancing the knowledge-base and industry’s ability to geologically store vast quantities of anthropogenic carbon. In support of this goal, a large-scale, stacked reservoir geologic model was developed for Gulf Coast sediments centered on the Citronelle Dome in southwest Alabama, the site of the SECARB Phase III Anthropogenic Test. Characterization of regional geology to construct the model consists of an assessment of the entire stratigraphic continuum at Citronelle Dome, from surface to the depth of the Donovan oil-bearing formation. This project utilizes all available geologic data available, which includes:more » modern geophysical well logs from three new wells drilled for SECARB’s Anthropogenic Test; vintage logs from the Citronelle oilfield wells; porosity and permeability data from whole core and sidewall cores obtained from the injection and observation wells drilled for the Anthropogenic Test; core data obtained from the SECARB Phase II saline aquifer injection test; regional core data for relevant formations from the Geological Survey of Alabama archives. Cross sections, isopach maps, and structure maps were developed to validate the geometry and architecture of the Citronelle Dome for building the model, and assuring that no major structural defects exist in the area. A synthetic neural network approach was used to predict porosity using the available SP and resistivity log data for the storage reservoir formations. These data are validated and applied to extrapolate porosity data over the study area wells, and to interpolate permeability amongst these data points. Geostatistical assessments were conducted over the study area. In addition to geologic characterization of the region, a suite of core analyses was conducted to construct a depositional model and constrain caprock integrity. Petrographic assessment of core was conducted by OSU and analyzed to build a depositional framework for the region and provide modern day analogues. Stability of the caprock over several test parameters was conducted by UAB to yield comprehensive measurements on long term stability of caprocks. The detailed geologic model of the full earth volume from surface thru the Donovan oil reservoir is incorporated into a state-of-the-art reservoir simulation conducted by the University of Alabama at Birmingham (UAB) to explore optimization of CO 2 injection and storage under different characterizations of reservoir flow properties. The application of a scaled up geologic modeling and reservoir simulation provides a proof of concept for the large scale volumetric modeling of CO 2 injection and storage the subsurface.« less

Fundamentals of Structural Geology

NASA Astrophysics Data System (ADS)

Pollard, David D.; Fletcher, Raymond C.

2005-09-01

Fundamentals of Structural Geology provides a new framework for the investigation of geological structures by integrating field mapping and mechanical analysis. Assuming a basic knowledge of physical geology, introductory calculus and physics, it emphasizes the observational data, modern mapping technology, principles of continuum mechanics, and the mathematical and computational skills, necessary to quantitatively map, describe, model, and explain deformation in Earth's lithosphere. By starting from the fundamental conservation laws of mass and momentum, the constitutive laws of material behavior, and the kinematic relationships for strain and rate of deformation, the authors demonstrate the relevance of solid and fluid mechanics to structural geology. This book offers a modern quantitative approach to structural geology for advanced students and researchers in structural geology and tectonics. It is supported by a website hosting images from the book, additional colour images, student exercises and MATLAB scripts. Solutions to the exercises are available to instructors. The book integrates field mapping using modern technology with the analysis of structures based on a complete mechanics MATLAB is used to visualize physical fields and analytical results and MATLAB scripts can be downloaded from the website to recreate textbook graphics and enable students to explore their choice of parameters and boundary conditions The supplementary website hosts color images of outcrop photographs used in the text, supplementary color images, and images of textbook figures for classroom presentations The textbook website also includes student exercises designed to instill the fundamental relationships, and to encourage the visualization of the evolution of geological structures; solutions are available to instructors

pyBadlands: A framework to simulate sediment transport, landscape dynamics and basin stratigraphic evolution through space and time

PubMed Central

2018-01-01

Understanding Earth surface responses in terms of sediment dynamics to climatic variability and tectonics forcing is hindered by limited ability of current models to simulate long-term evolution of sediment transfer and associated morphological changes. This paper presents pyBadlands, an open-source python-based framework which computes over geological time (1) sediment transport from landmasses to coasts, (2) reworking of marine sediments by longshore currents and (3) development of coral reef systems. pyBadlands is cross-platform, distributed under the GPLv3 license and available on GitHub (http://github.com/badlands-model). Here, we describe the underlying physical assumptions behind the simulated processes and the main options already available in the numerical framework. Along with the source code, a list of hands-on examples is provided that illustrates the model capabilities. In addition, pre and post-processing classes have been built and are accessible as a companion toolbox which comprises a series of workflows to efficiently build, quantify and explore simulation input and output files. While the framework has been primarily designed for research, its simplicity of use and portability makes it a great tool for teaching purposes. PMID:29649301

Co-optimization of CO 2 -EOR and Storage Processes under Geological Uncertainty

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ampomah, William; Balch, Robert; Will, Robert

This paper presents an integrated numerical framework to co-optimize EOR and CO 2 storage performance in the Farnsworth field unit (FWU), Ochiltree County, Texas. The framework includes a field-scale compositional reservoir flow model, an uncertainty quantification model and a neural network optimization process. The reservoir flow model has been constructed based on the field geophysical, geological, and engineering data. A laboratory fluid analysis was tuned to an equation of state and subsequently used to predict the thermodynamic minimum miscible pressure (MMP). A history match of primary and secondary recovery processes was conducted to estimate the reservoir and multiphase flow parametersmore » as the baseline case for analyzing the effect of recycling produced gas, infill drilling and water alternating gas (WAG) cycles on oil recovery and CO 2 storage. A multi-objective optimization model was defined for maximizing both oil recovery and CO 2 storage. The uncertainty quantification model comprising the Latin Hypercube sampling, Monte Carlo simulation, and sensitivity analysis, was used to study the effects of uncertain variables on the defined objective functions. Uncertain variables such as bottom hole injection pressure, WAG cycle, injection and production group rates, and gas-oil ratio among others were selected. The most significant variables were selected as control variables to be used for the optimization process. A neural network optimization algorithm was utilized to optimize the objective function both with and without geological uncertainty. The vertical permeability anisotropy (Kv/Kh) was selected as one of the uncertain parameters in the optimization process. The simulation results were compared to a scenario baseline case that predicted CO 2 storage of 74%. The results showed an improved approach for optimizing oil recovery and CO 2 storage in the FWU. The optimization process predicted more than 94% of CO 2 storage and most importantly about 28% of incremental oil recovery. The sensitivity analysis reduced the number of control variables to decrease computational time. A risk aversion factor was used to represent results at various confidence levels to assist management in the decision-making process. The defined objective functions were proved to be a robust approach to co-optimize oil recovery and CO 2 storage. The Farnsworth CO 2 project will serve as a benchmark for future CO 2–EOR or CCUS projects in the Anadarko basin or geologically similar basins throughout the world.« less

Co-optimization of CO 2 -EOR and Storage Processes under Geological Uncertainty

DOE PAGES

Ampomah, William; Balch, Robert; Will, Robert; ...

2017-07-01

This paper presents an integrated numerical framework to co-optimize EOR and CO 2 storage performance in the Farnsworth field unit (FWU), Ochiltree County, Texas. The framework includes a field-scale compositional reservoir flow model, an uncertainty quantification model and a neural network optimization process. The reservoir flow model has been constructed based on the field geophysical, geological, and engineering data. A laboratory fluid analysis was tuned to an equation of state and subsequently used to predict the thermodynamic minimum miscible pressure (MMP). A history match of primary and secondary recovery processes was conducted to estimate the reservoir and multiphase flow parametersmore » as the baseline case for analyzing the effect of recycling produced gas, infill drilling and water alternating gas (WAG) cycles on oil recovery and CO 2 storage. A multi-objective optimization model was defined for maximizing both oil recovery and CO 2 storage. The uncertainty quantification model comprising the Latin Hypercube sampling, Monte Carlo simulation, and sensitivity analysis, was used to study the effects of uncertain variables on the defined objective functions. Uncertain variables such as bottom hole injection pressure, WAG cycle, injection and production group rates, and gas-oil ratio among others were selected. The most significant variables were selected as control variables to be used for the optimization process. A neural network optimization algorithm was utilized to optimize the objective function both with and without geological uncertainty. The vertical permeability anisotropy (Kv/Kh) was selected as one of the uncertain parameters in the optimization process. The simulation results were compared to a scenario baseline case that predicted CO 2 storage of 74%. The results showed an improved approach for optimizing oil recovery and CO 2 storage in the FWU. The optimization process predicted more than 94% of CO 2 storage and most importantly about 28% of incremental oil recovery. The sensitivity analysis reduced the number of control variables to decrease computational time. A risk aversion factor was used to represent results at various confidence levels to assist management in the decision-making process. The defined objective functions were proved to be a robust approach to co-optimize oil recovery and CO 2 storage. The Farnsworth CO 2 project will serve as a benchmark for future CO 2–EOR or CCUS projects in the Anadarko basin or geologically similar basins throughout the world.« less

Geologic framework for the national assessment of carbon dioxide storage resources: Alaska North Slope and Kandik Basin, Alaska: Chapter I in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Craddock, William H.; Buursink, Marc L.; Covault, Jacob A.; Brennan, Sean T.; Doolan, Colin A.; Drake II, Ronald M.; Merrill, Matthew D.; Roberts-Ashby, Tina L.; Slucher, Ernie R.; Warwick, Peter D.; Blondes, Madalyn S.; Freeman, P.A.; Cahan, Steven N.; DeVera, Christina A.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2014-01-01

For each SAU in both of the basins, we discuss the areal distribution of suitable CO2 sequestration reservoir rock. We also characterize the overlying sealing unit and describe the geologic characteristics that influence the potential CO2 storage volume and reservoir performance. These characteristics include reservoir depth, gross thickness, net thickness, porosity, permeability, and groundwater salinity. Case-by-case strategies for estimating the pore volume existing within structurally and (or) stratigraphically closed traps are presented. Although assessment results are not contained in this report, the geologic information included herein was employed to calculate the potential storage volume in the various SAUs. Lastly, in this report, we present the rationale for not conducting assessment work in fifteen sedimentary basins distributed across the Alaskan interior and within Alaskan State waters.

Model for CO2 leakage including multiple geological layers and multiple leaky wells.

PubMed

Nordbotten, Jan M; Kavetski, Dmitri; Celia, Michael A; Bachu, Stefan

2009-02-01

Geological storage of carbon dioxide (CO2) is likely to be an integral component of any realistic plan to reduce anthropogenic greenhouse gas emissions. In conjunction with large-scale deployment of carbon storage as a technology, there is an urgent need for tools which provide reliable and quick assessments of aquifer storage performance. Previously, abandoned wells from over a century of oil and gas exploration and production have been identified as critical potential leakage paths. The practical importance of abandoned wells is emphasized by the correlation of heavy CO2 emitters (typically associated with industrialized areas) to oil and gas producing regions in North America. Herein, we describe a novel framework for predicting the leakage from large numbers of abandoned wells, forming leakage paths connecting multiple subsurface permeable formations. The framework is designed to exploit analytical solutions to various components of the problem and, ultimately, leads to a grid-free approximation to CO2 and brine leakage rates, as well as fluid distributions. We apply our model in a comparison to an established numerical solverforthe underlying governing equations. Thereafter, we demonstrate the capabilities of the model on typical field data taken from the vicinity of Edmonton, Alberta. This data set consists of over 500 wells and 7 permeable formations. Results show the flexibility and utility of the solution methods, and highlight the role that analytical and semianalytical solutions can play in this important problem.

Geologic map of the Stephens City quadrangle, Clark, Frederick, and Warren Counties, Virginia

USGS Publications Warehouse

Weary, D.J.; Orndorff, R.C.; Aleman-Gonzalez, W.

2006-01-01

The Stephens City 1:24,000-scale quadrangle is one of several quadrangles in Frederick County, Virginia being mapped by geologists from the U.S. Geological Survey in Reston, VA with funding from the National Cooperative Geologic Mapping Program. This work is part of a project being lead by the U.S. Geological Survey Water Resources Discipline, Virginia District, to investigate the geologic framework and groundwater resources of Frederick County as well as other areas in the northern Shenandoah Valley of Virginia and West Virginia.

A Hydrostratigraphic System for Modeling Groundwater Flow and Radionuclide Migration at the Corrective Action Unit Scale, Nevada Test Site and Surrounding Areas, Clark, Lincoln, and Nye Counties, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prothro, Lance; Drellack Jr., Sigmund; Mercadante, Jennifer

2009-01-31

Underground Test Area (UGTA) corrective action unit (CAU) groundwater flow and contaminant transport models of the Nevada Test Site (NTS) and vicinity are built upon hydrostratigraphic framework models (HFMs) that utilize the hydrostratigraphic unit (HSU) as the fundamental modeling component. The delineation and three-dimensional (3-D) modeling of HSUs within the highly complex geologic terrain that is the NTS requires a hydrostratigraphic system that is internally consistent, yet flexible enough to account for overlapping model areas, varied geologic terrain, and the development of multiple alternative HFMs. The UGTA CAU-scale hydrostratigraphic system builds on more than 50 years of geologic and hydrologicmore » work in the NTS region. It includes 76 HSUs developed from nearly 300 stratigraphic units that span more than 570 million years of geologic time, and includes rock units as diverse as marine carbonate and siliciclastic rocks, granitic intrusives, rhyolitic lavas and ash-flow tuffs, and alluvial valley-fill deposits. The UGTA CAU-scale hydrostratigraphic system uses a geology-based approach and two-level classification scheme. The first, or lowest, level of the hydrostratigraphic system is the hydrogeologic unit (HGU). Rocks in a model area are first classified as one of ten HGUs based on the rock’s ability to transmit groundwater (i.e., nature of their porosity and permeability), which at the NTS is mainly a function of the rock’s primary lithology, type and degree of postdepositional alteration, and propensity to fracture. The second, or highest, level within the UGTA CAU-scale hydrostratigraphic system is the HSU, which is the fundamental mapping/modeling unit within UGTA CAU-scale HFMs. HSUs are 3-D bodies that are represented in the finite element mesh for the UGTA groundwater modeling process. HSUs are defined systematically by stratigraphically organizing HGUs of similar character into larger HSUs designations. The careful integration of stratigraphic information in the development of HSUs is important to assure individual HSUs are internally consistent, correlatable, and mappable throughout all the model areas.« less

Towards a New Framework for Interpreting Relations Between Mantle Dynamics and Processes at the Earth's Surface: A Case Study Involving the Deccan Traps

NASA Astrophysics Data System (ADS)

Glisovic, P.; Forte, A. M.

2017-12-01

An outstanding challenge in modern geodynamics is the utilization of mantle convection models and geophysical data to successfully explain geological events and processes that alter Earth's biosphere, climate, and surface. A key challenge in this modelling is the determination of the initial (and unknown) configuration of mantle heterogeneity in the geological past. The first step in addressing this challenge is recognizing that seismic tomography is our most powerful tool for mapping the present-day, internal structure of the mantle. We, therefore, implemented a new back-and-forth iterative method for time-reversed, tomography-based convection modelling to reconstruct Earth's internal 3-D structure and dynamics over the Cenozoic [Glisovic & Forte 2016 (JGR)]. This backward convection modelling also includes another key input - the depth variation of mantle viscosity inferred from joint inversions of the global convection-related observables and a suite of glacial isostatic adjustments (GIA) data [Mitrovica & Forte 2004 (EPSL), Forte et al. 2010 (EPSL)]. This state-of-the-art, time-reversed convection model is able to show that massive outpourings of basalt in west-central India, known as the Deccan Traps, about 65 million years ago can be directly linked to the presence of two different deep-mantle hotspots: Réunion and Comores [Glisovic & Forte 2017 (Science)]. This work constitutes case study showing how time-reversed convection modelling provides a new framework for interpreting the relations between mantle dynamics and changing paleogeography and it provides a roadmap for a new series of studies that will elucidate these linkages.

Sediment data collected in 2014 and 2015 from around Breton and Gosier Islands, Breton National Wildlife Refuge, Louisiana

USGS Publications Warehouse

Bernier, Julie C.; Kelso, Kyle W.; Tuten, Thomas M.; Stalk, Chelsea A.; Flocks, James G.

2017-03-08

Breton Island, located at the southern end of the Chandeleur Islands, supports one of Louisiana’s largest historical brown pelican (Pelecanus occidentalis) nesting colonies. Although the brown pelican was delisted as an endangered species in 2009, nesting areas are threatened by continued land loss and are extremely vulnerable to storm impacts. The U.S. Fish and Wildlife Service proposed to restore Breton Island to pre-Hurricane Katrina conditions through rebuilding the shoreface, dune, and back-barrier marsh environments. Prior to restoration, scientists from the U.S. Geological Survey’s (USGS) St. Petersburg Coastal and Marine Science Center Geologic and Morphologic Evolution of Coastal Margins project collected high-resolution geophysical (topography, bathymetry, and sub-bottom profiles) and sedimentologic data from around Breton Island to characterize the geologic framework of the island platform, nearshore, and shelf environments. These data will be used to characterize the geologic framework around Breton Island, identify potential borrow areas for restoration efforts, quantify seafloor change, and provide information for sediment transport and morphologic change models to assess island response to restoration and natural processes.This report, along with the accompanying USGS data release, serves as an archive of sediment data from vibracores, push cores, and submerged grab samples collected from around Breton and Gosier Islands, Louisiana, during two surveys conducted in July 2014 and January 2015 (USGS Field Activity Numbers 2014–314–FA and 2014–336–FA, respectively). Sedimentologic and stratigraphic metrics (for example, sediment texture or unit thicknesses) derived from these data can be used to ground-truth the geophysical data and characterize potential sand resources or can be incorporated into sediment transport or morphologic change models. Data products, including sample location tables, descriptive core logs, core photographs and x-radiographs, results of sediment grain-size analyses, and geographic information system data files with accompanying formal Federal Geographic Data Committee metadata can be downloaded from the accompanying data release.

Neural network modeling and an uncertainty analysis in Bayesian framework: A case study from the KTB borehole site

NASA Astrophysics Data System (ADS)

Maiti, Saumen; Tiwari, Ram Krishna

2010-10-01

A new probabilistic approach based on the concept of Bayesian neural network (BNN) learning theory is proposed for decoding litho-facies boundaries from well-log data. We show that how a multi-layer-perceptron neural network model can be employed in Bayesian framework to classify changes in litho-log successions. The method is then applied to the German Continental Deep Drilling Program (KTB) well-log data for classification and uncertainty estimation in the litho-facies boundaries. In this framework, a posteriori distribution of network parameter is estimated via the principle of Bayesian probabilistic theory, and an objective function is minimized following the scaled conjugate gradient optimization scheme. For the model development, we inflict a suitable criterion, which provides probabilistic information by emulating different combinations of synthetic data. Uncertainty in the relationship between the data and the model space is appropriately taken care by assuming a Gaussian a priori distribution of networks parameters (e.g., synaptic weights and biases). Prior to applying the new method to the real KTB data, we tested the proposed method on synthetic examples to examine the sensitivity of neural network hyperparameters in prediction. Within this framework, we examine stability and efficiency of this new probabilistic approach using different kinds of synthetic data assorted with different level of correlated noise. Our data analysis suggests that the designed network topology based on the Bayesian paradigm is steady up to nearly 40% correlated noise; however, adding more noise (˜50% or more) degrades the results. We perform uncertainty analyses on training, validation, and test data sets with and devoid of intrinsic noise by making the Gaussian approximation of the a posteriori distribution about the peak model. We present a standard deviation error-map at the network output corresponding to the three types of the litho-facies present over the entire litho-section of the KTB. The comparisons of maximum a posteriori geological sections constructed here, based on the maximum a posteriori probability distribution, with the available geological information and the existing geophysical findings suggest that the BNN results reveal some additional finer details in the KTB borehole data at certain depths, which appears to be of some geological significance. We also demonstrate that the proposed BNN approach is superior to the conventional artificial neural network in terms of both avoiding "over-fitting" and aiding uncertainty estimation, which are vital for meaningful interpretation of geophysical records. Our analyses demonstrate that the BNN-based approach renders a robust means for the classification of complex changes in the litho-facies successions and thus could provide a useful guide for understanding the crustal inhomogeneity and the structural discontinuity in many other tectonically complex regions.

A national framework for monitoring and reporting on environmental sustainability in Canada.

PubMed

Marshall, I B; Scott Smith, C A; Selby, C J

1996-01-01

In 1991, a collaborative project to revise the terrestrial component of a national ecological framework was undertaken with a wide range of stakeholders. This spatial framework consists of multiple, nested levels of ecological generalization with linkages to existing federal and provincial scientific databases. The broadest level of generalization is the ecozone. Macroclimate, major vegetation types and subcontinental scale physiographic formations constitute the definitive components of these major ecosystems. Ecozones are subdivided into approximately 200 ecoregions which are based on properties like regional physiography, surficial geology, climate, vegetation, soil, water and fauna. The ecozone and ecoregion levels of the framework have been depicted on a national map coverage at 1:7 500 000 scale. Ecoregions have been subdivided into ecodistricts based primarily on landform, parent material, topography, soils, waterbodies and vegetation at a scale (1:2 000 000) useful for environmental resource management, monitoring and modelling activities. Nested within the ecodistricts are the polygons that make up the Soil Landscapes of Canada series of 1:1 000 000 scale soil maps. The framework is supported by an ARC-INFO GIS at Agriculture Canada. The data model allows linkage to associated databases on climate, land use and socio-economic attributes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ernest A. Mancini

The University of Alabama in cooperation with Texas A&M University, McGill University, Longleaf Energy Group, Strago Petroleum Corporation, and Paramount Petroleum Company are undertaking an integrated, interdisciplinary geoscientific and engineering research project. The project is designed to characterize and model reservoir architecture, pore systems and rock-fluid interactions at the pore to field scale in Upper Jurassic Smackover reef and carbonate shoal reservoirs associated with varying degrees of relief on pre-Mesozoic basement paleohighs in the northeastern Gulf of Mexico. The project effort includes the prediction of fluid flow in carbonate reservoirs through reservoir simulation modeling which utilizes geologic reservoir characterization andmore » modeling and the prediction of carbonate reservoir architecture, heterogeneity and quality through seismic imaging. The primary objective of the project is to increase the profitability, producibility and efficiency of recovery of oil from existing and undiscovered Upper Jurassic fields characterized by reef and carbonate shoals associated with pre-Mesozoic basement paleohighs. The principal research effort for Year 2 of the project has been reservoir characterization, 3-D modeling and technology transfer. This effort has included six tasks: (1) the study of rockfluid interactions, (2) petrophysical and engineering characterization, (3) data integration, (4) 3-D geologic modeling, (5) 3-D reservoir simulation and (6) technology transfer. This work was scheduled for completion in Year 2. Overall, the project work is on schedule. Geoscientific reservoir characterization is essentially completed. The architecture, porosity types and heterogeneity of the reef and shoal reservoirs at Appleton and Vocation Fields have been characterized using geological and geophysical data. The study of rock-fluid interactions is near completion. Observations regarding the diagenetic processes influencing pore system development and heterogeneity in these reef and shoal reservoirs have been made. Petrophysical and engineering property characterization has been essentially completed. Porosity and permeability data at Appleton and Vocation Fields have been analyzed, and well performance analysis has been conducted. Data integration is up to date, in that, the geological, geophysical, petrophysical and engineering data collected to date for Appleton and Vocation Fields have been compiled into a fieldwide digital database. 3-D geologic modeling of the structures and reservoirs at Appleton and Vocation Fields has been completed. The model represents an integration of geological, petrophysical and seismic data. 3-D reservoir simulation of the reservoirs at Appleton and Vocation Fields has been completed. The 3-D geologic model served as the framework for the simulations. A technology workshop on reservoir characterization and modeling at Appleton and Vocation Fields was conducted to transfer the results of the project to the petroleum industry.« less

Geologic framework for the national assessment of carbon dioxide storage resources─South Florida Basin: Chapter L in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Roberts-Ashby, Tina L.; Brennan, Sean T.; Merrill, Matthew D.; Blondes, Madalyn S.; Freeman, P.A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2015-08-26

This report presents five storage assessment units (SAUs) that have been identified as potentially suitable for geologic carbon dioxide sequestration within a 35,075-square-mile area that includes the entire onshore and State-water portions of the South Florida Basin. Platform-wide, thick successions of laterally extensive carbonates and evaporites deposited in highly cyclic depositional environments in the South Florida Basin provide several massive, porous carbonate reservoirs that are separated by evaporite seals. For each storage assessment unit identified within the basin, the areal distribution of the reservoir-seal couplet identified as suitable for geologic Carbon dioxide sequestration is presented, along with a description of the geologic characteristics that influence the potential carbon dioxide storage volume and reservoir performance. On a case-by-case basis, strategies for estimating the pore volume existing within structurally and (or) stratigraphically closed traps are also discussed. Geologic information presented in this report has been employed to calculate potential storage capacities for carbon dioxide sequestration in the storage assessment units assessed herein, although complete assessment results are not contained in this report.

Transboundary study of the Milk River aquifer (Canada, USA): geological, conceptual and numerical models for the sound management of the regional groundwater resources

NASA Astrophysics Data System (ADS)

Pétré, Marie-Amélie; Rivera, Alfonso; Lefebvre, René

2016-04-01

The Milk River transboundary aquifer straddles southern Alberta (Canada) and northern Montana (United States), a semi-arid and water-short region. The extensive use of this regional sandstone aquifer over the 20th century has led to a major drop in water levels locally, and concerns about the durability of the resources have been raised since the mid-1950. Even though the Milk River Aquifer (MRA) has been studied for decades, most of the previous studies were limited by the international border, preventing a sound understanding of the aquifer dynamics. Yet, a complete portrait of the aquifer is required for proper management of this shared resource. The transboundary study of the MRA aims to overcome transboundary limitations by providing a comprehensive characterization of the groundwater resource at the aquifer scale, following a three-stage approach: 1) The development of a 3D unified geological model of the MRA (50,000 km2). The stratigraphic framework on both sides of the border was harmonized and various sources of geological data were unified to build the transboundary geological model. The delineation of the aquifer and the geometry and thicknesses of the geological units were defined continuously across the border. 2) Elaboration of a conceptual hydrogeological model by linking hydrogeological and geochemical data with the 3D unified geological model. This stage is based on a thorough literature review and focused complementary field work on both sides of the border. The conceptual model includes the determination of the groundwater flow pattern, the spatial distribution of hydraulic properties, a groundwater budget and the definition of the groundwater types. Isotopes (3H, 14C, 36Cl) were used to delineate the recharge area as well as the active and low-flow areas. 3) The building of a 3D numerical groundwater flow model of the MRA (26,000 km2). This model is a transposition of the geological and hydrogeological conceptual models. A pre-exploitation steady-state model and a subsequent transient numerical model with several exploitation scenarios were developed. The numerical model aims to test the conceptual model and to provide a basis to assess the best possible uses of this valuable resource that is shared by Canada and the United States of America. This study provides a unique approach with scientific tools for proper aquifer assessment and groundwater management at the aquifer scale, not interrupted by a jurisdictional boundary. These tools are combined and integrated into three models, which together will form the basis of reliable sustainable groundwater and aquifer management in cooperation, thus facilitating the creation of a system of transboundary water governance based on scientific knowledge.

Magnetotelluric Data, Central Yucca Flat, Nevada Test Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.M. Williams; B.D. Rodriguez, and T.H. Asch

2005-11-23

Nuclear weapons are integral to the defense of the United States. The U.S. Department of Energy, as the steward of these devices, must continue to gauge the efficacy of the individual weapons. This could be accomplished by occasional testing at the Nevada Test Site (NTS) in Nevada, northwest of Las Vegas. Yucca Flat Basin is one of the testing areas at the NTS. One issue of concern is the nature of the somewhat poorly constrained pre-Tertiary geology and its effects on ground-water flow in the area subsequent to a nuclear test. Ground-water modelers would like to know more about themore » hydrostratigraphy and geologic structure to support a hydrostratigraphic framework model that is under development for the Yucca Flat Corrective Action Unit (CAU). During 2003, the U.S. Geological Survey (USGS) collected and processed Magnetotelluric (MT) and Audio-magnetotelluric (AMT) data at the Nevada Test Site in and near Yucca Flat to help characterize this pre-Tertiary geology. That work will help to define the character, thickness, and lateral extent of pre-Tertiary confining units. In particular, a major goal has been to define the upper clastic confining unit (UCCU) in the Yucca Flat area. Interpretation will include a three-dimensional (3-D) character analysis and two-dimensional (2-D) resistivity model. The purpose of this report is to release the MT sounding data for Central Yucca Flat, Profile 1, as shown in figure 1. No interpretation of the data is included here.« less

Magnetotelluric Data, North Central Yucca Flat, Nevada Test Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.M. Williams; B.D. Rodriguez, and T.H. Asch

2005-11-23

Nuclear weapons are integral to the defense of the United States. The U.S. Department of Energy, as the steward of these devices, must continue to gauge the efficacy of the individual weapons. This could be accomplished by occasional testing at the Nevada Test Site (NTS) in Nevada, northwest of Las Vegas. Yucca Flat Basin is one of the testing areas at the NTS. One issue of concern is the nature of the somewhat poorly constrained pre-Tertiary geology and its effects on ground-water flow in the area subsequent to a nuclear test. Ground-water modelers would like to know more about themore » hydrostratigraphy and geologic structure to support a hydrostratigraphic framework model that is under development for the Yucca Flat Corrective Action Unit (CAU). During 2003, the U.S. Geological Survey (USGS) collected and processed Magnetotelluric (MT) and Audio-magnetotelluric (AMT) data at the Nevada Test Site in and near Yucca Flat to help characterize this pre-Tertiary geology. That work will help to define the character, thickness, and lateral extent of pre-Tertiary confining units. In particular, a major goal has been to define the upper clastic confining unit (UCCU) in the Yucca Flat area. Interpretation will include a three-dimensional (3-D) character analysis and two-dimensional (2-D) resistivity model. The purpose of this report is to release the MT sounding data for north central Yucca Flat, Profile 7, as shown in Figure 1. No interpretation of the data is included here.« less

Magnetotelluric Data, Northern Frenchman Flat, Nevada Test Site Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.M. Williams; B.D. Rodriguez, and T. H. Asch

2005-11-23

Nuclear weapons are integral to the defense of the United States. The U.S. Department of Energy, as the steward of these devices, must continue to gauge the efficacy of the individual weapons. This could be accomplished by occasional testing at the Nevada Test Site (NTS) in Nevada, northwest of Las Vegas. Yucca Flat Basin is one of the testing areas at the NTS. One issue of concern is the nature of the somewhat poorly constrained pre-Tertiary geology and its effects on ground-water flow in the area subsequent to a nuclear test. Ground-water modelers would like to know more about themore » hydrostratigraphy and geologic structure to support a hydrostratigraphic framework model that is under development for the Yucca Flat Corrective Action Unit (CAU). During 2003, the U.S. Geological Survey (USGS) collected and processed Magnetotelluric (MT) and Audio-magnetotelluric (AMT) data at the Nevada Test Site in and near Yucca Flat to help characterize this pre-Tertiary geology. That work will help to define the character, thickness, and lateral extent of pre-Tertiary confining units. In particular, a major goal has been to define the upper clastic confining unit (UCCU) in the Yucca Flat area. Interpretation will include a three-dimensional (3-D) character analysis and two-dimensional (2-D) resistivity model. The purpose of this report is to release the MT sounding data for Frenchman Flat Profile 3, as shown in Figure 1. No interpretation of the data is included here.« less

Magnetotelluric Data, Across Quartzite Ridge, Nevada Test Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.M. Williams; B.D. Rodriguez, and T.H. Asch

2005-11-23

Nuclear weapons are integral to the defense of the United States. The U.S. Department of Energy, as the steward of these devices, must continue to gauge the efficacy of the individual weapons. This could be accomplished by occasional testing at the Nevada Test Site (NTS) in Nevada, northwest of Las Vegas. Yucca Flat Basin is one of the testing areas at the NTS. One issue of concern is the nature of the somewhat poorly constrained pre-Tertiary geology and its effects on ground-water flow in the area subsequent to a nuclear test. Ground-water modelers would like to know more about themore » hydrostratigraphy and geologic structure to support a hydrostratigraphic framework model that is under development for the Yucca Flat Corrective Action Unit (CAU). During 2003, the U.S. Geological Survey (USGS) collected and processed Magnetotelluric (MT) and Audio-magnetotelluric (AMT) data at the Nevada Test Site in and near Yucca Flat to help characterize this pre-Tertiary geology. That work will help to define the character, thickness, and lateral extent of pre-Tertiary confining units. In particular, a major goal has been to define the upper clastic confining unit (UCCU) in the Yucca Flat area. Interpretation will include a three-dimensional (3-D) character analysis and two-dimensional (2-D) resistivity model. The purpose of this report is to release the MT soundings across Quartzite Ridge, Profiles 5, 6a, and 6b, as shown in Figure 1. No interpretation of the data is included here.« less

Magnetotelluric Data, Southern Yucca Flat, Nevada Test Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.M. Williams; B.D. Rodriguez, and T.H. Asch

2005-11-23

Nuclear weapons are integral to the defense of the United States. The U.S. Department of Energy, as the steward of these devices, must continue to gauge the efficacy of the individual weapons. This could be accomplished by occasional testing at the Nevada Test Site (NTS) in Nevada, northwest of Las Vegas. Yucca Flat Basin is one of the testing areas at the NTS. One issue of concern is the nature of the somewhat poorly constrained pre-Tertiary geology and its effects on ground-water flow in the area subsequent to a nuclear test. Ground-water modelers would like to know more about themore » hydrostratigraphy and geologic structure to support a hydrostratigraphic framework model that is under development for the Yucca Flat Corrective Action Unit (CAU). During 2003, the U.S. Geological Survey (USGS) collected and processed Magnetotelluric (MT) and Audio-magnetotelluric (AMT) data at the Nevada Test Site in and near Yucca Flat to help characterize this pre-Tertiary geology. That work will help to define the character, thickness, and lateral extent of pre-Tertiary confining units. In particular, a major goal has been to define the upper clastic confining unit (UCCU) in the Yucca Flat area. Interpretation will include a three-dimensional (3-D) character analysis and two-dimensional (2-D) resistivity model. The purpose of this report is to release the MT sounding data for Southern Yucca Flat, Profile 4, as shown in Figure 1. No interpretation of the data is included here.« less

Magnetotelluric Data, Northern Yucca Flat, Nevada Test Site, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.M. Williams; B.D. Rodriguez, and T.H. Asch

2005-11-23

Nuclear weapons are integral to the defense of the United States. The U.S. Department of Energy, as the steward of these devices, must continue to gauge the efficacy of the individual weapons. This could be accomplished by occasional testing at the Nevada Test Site (NTS) in Nevada, northwest of Las Vegas. Yucca Flat Basin is one of the testing areas at the NTS. One issue of concern is the nature of the somewhat poorly constrained pre-Tertiary geology and its effects on ground-water flow in the area subsequent to a nuclear test. Ground-water modelers would like to know more about themore » hydrostratigraphy and geologic structure to support a hydrostratigraphic framework model that is under development for the Yucca Flat Corrective Action Unit (CAU). During 2003, the U.S. Geological Survey (USGS) collected and processed Magnetotelluric (MT) and Audio-magnetotelluric (AMT) data at the Nevada Test Site in and near Yucca Flat to help characterize this pre-Tertiary geology. That work will help to define the character, thickness, and lateral extent of pre-Tertiary confining units. In particular, a major goal has been to define the upper clastic confining unit (UCCU) in the Yucca Flat area. Interpretation will include a three-dimensional (3-D) character analysis and two-dimensional (2-D) resistivity model. The purpose of this report is to release the MT sounding data for Profile 2, (fig. 1), located in the northern Yucca Flat area. No interpretation of the data is included here.« less

An optimized workflow for building 3D models from balanced sections and potential field geophysics: a study case in NE Spain.

NASA Astrophysics Data System (ADS)

Ayala, Conxi; Izquierdo-Llavall, Esther; Pueyo, Emilio Luis; Rubio, Félix; Rodríguez-Pintó, Adriana; María Casas, Antonio; Oliva-Urcía, Belén; Rey-Moral, Carmen

2015-04-01

Obtaining an accurate 3D image of the geometry and physical properties of geological structures in depth is a challenge regardless the scale and the aim of the investigation. In this framework, assessing the origin of the uncertainties and reducing them is a key issue when building a 3D reconstruction of a target area. Usually, this process involves an interdisciplinary approach and also the use of different software whose inputs and outputs have to be interoperable. We have designed a new workflow for 2.5D and 3D geological and potential field modelling, especially useful in areas where no seismic data is available. The final aim is to obtain a 3D geological model, at a regional or local scale, with the smaller uncertainty as possible. Once the study area and the working scale are is decided, the first obvious step is to compile all preexisting data and to determine its uncertainties. If necessary, a survey will be carried out to acquire additional data (e.g., gravity, magnetic or petrophysical data) to have an appropriated coverage of information and rock samples. A thorough study of the petrophysical properties is made to determine the density, magnetic susceptibility and remanence that will be assigned to each lithology, together with its corresponding uncertainty. Finally, the modelling process is started, and it includes a feedback between geology and potential fields in order to progressively refine the model until it fits all the existing data. The procedure starts with the construction of balanced geological cross sections from field work, available geological maps as well as data from stratigraphic columns, boreholes, etc. These geological cross sections are exported and imported in GMSYS software to carry out the 2.5D potential field modelling. The model improves and its uncertainty is reduced through the feedback between the geologists and the geophysicists. Once the potential field anomalies are well adjusted, the cross sections are exported into 3DMove (Midland Valley) to construct a preliminary balanced 3D model. Inversion of the potential field data in GeoModeller is the final step to obtain a 3D model consistent with the input data and with the minimum possible uncertainty. Our case study is a 3D model from the Linking Zone between the Iberian Range and the Catalonian Costal ones (NE Spain, an extension of 11,325 km2). No seismic data was available, so we carried out several surveys to acquire new gravity data and rock samples to complete the data from IGME petrophysical databases. A total of 1470 samples have been used to define the physical properties for the modelled lithologies. The gravity data consists of 2902 stations. The initial model is based on the surface geology, eleven boreholes and 8 balanced geological cross sections built in the frame of this research. The final model resulted from gravimetric inversion has allowed us to define the geometry of the top of the basement as well as to identify two structures (anticlines) as potential CO2 reservoirs.

Quaternary geomorphology and modern coastal development in response to an inherent geologic framework: An example from Charleston, South Carolina

USGS Publications Warehouse

Harris, M.S.; Gayes, P.T.; Kindinger, J.L.; Flocks, J.G.; Krantz, D.E.; Donovan, P.

2005-01-01

Coastal landscapes evolve over wide-ranging spatial and temporal scales in response to physical and biological pro-cesses that interact with a wide range of variables. To develop better predictive models for these dynamic areas, we must understand the influence of these variables on coastal morphologies and ultimately how they influence coastal processes. This study defines the influence of geologic framework variability on a classic mixed-energy coastline, and establishes four categorical scales of spatial and temporal influence on the coastal system. The near-surface, geologic framework was delineated using high-resolution seismic profiles, shallow vibracores, detailed geomorphic maps, historical shorelines, aerial photographs, and existing studies, and compared to the long- and short-term development of two coastal compartments near Charleston, South Carolina. Although it is clear that the imprint of a mixed-energy tidal and wave signal (basin-scale) dictates formation of drumstick barriers and that immediate responses to wave climate are dramatic, island size, position, and longer-term dynamics are influenced by a series of inherent, complex near-surface stratigraphic geometries. Major near-surface Tertiary geometries influence inlet placement and drainage development (island-scale) through multiple interglacial cycles and overall channel morphology (local-scale). During the modern marine transgression, the halo of ebb-tidal deltas greatly influence inlet region dynamics, while truncated beach ridges and exposed, differentially erodable Cenozoic deposits in the active system influence historical shoreline dynamics and active shoreface morphologies (blockscale). This study concludes that the mixed-energy imprint of wave and tide theories dominates general coastal morphology, but that underlying stratigraphic influences on the coast provide site-specific, long-standing imprints on coastal evolution.

Quaternary geophysical framework of the northeastern North Carolina coastal system

USGS Publications Warehouse

Thieler, E.R.; Foster, D.S.; Mallinson, D.M.; Himmelstoss, E.A.; McNinch, J.E.; List, J.H.; Hammar-Klose, E.S.

2013-01-01

The northeastern North Carolina coastal system, from False Cape, Virginia, to Cape Lookout, North Carolina, has been studied by a cooperative research program that mapped the Quaternary geologic framework of the estuaries, barrier islands, and inner continental shelf. This information provides a basis to understand the linkage between geologic framework, physical processes, and coastal evolution at time scales from storm events to millennia. The study area attracts significant tourism to its parks and beaches, contains a number of coastal communities, and supports a local fishing industry, all of which are impacted by coastal change. Knowledge derived from this research program can be used to mitigate hazards and facilitate effective management of this dynamic coastal system.

Crater-based dating of geological units on Mars: methods and application for the new global geological map

USGS Publications Warehouse

Platz, Thomas; Michael, Gregory; Tanaka, Kenneth L.; Skinner, James A.; Fortezzo, Corey M.

2013-01-01

The new, post-Viking generation of Mars orbital imaging and topographical data provide significant higher-resolution details of surface morphologies, which induced a new effort to photo-geologically map the surface of Mars at 1:20,000,000 scale. Although from unit superposition relations a relative stratigraphical framework can be compiled, it was the ambition of this mapping project to provide absolute unit age constraints through crater statistics. In this study, the crater counting method is described in detail, starting with the selection of image data, type locations (both from the mapper’s and crater counter’s perspectives) and the identification of impact craters. We describe the criteria used to validate and analyse measured crater populations, and to derive and interpret crater model ages. We provide examples of how geological information about the unit’s resurfacing history can be retrieved from crater size–frequency distributions. Three cases illustrate short-, intermediate, and long-term resurfacing histories. In addition, we introduce an interpretation-independent visualisation of the crater resurfacing history that uses the reduction of the crater population in a given size range relative to the expected population given the observed crater density at larger sizes. From a set of potential type locations, 48 areas from 22 globally mapped units were deemed suitable for crater counting. Because resurfacing ages were derived from crater statistics, these secondary ages were used to define the unit age rather than the base age. Using the methods described herein, we modelled ages that are consistent with the interpreted stratigraphy. Our derived model ages allow age assignments to be included in unit names. We discuss the limitations of using the crater dating technique for global-scale geological mapping. Finally, we present recommendations for the documentation and presentation of crater statistics in publications.

Geologic framework for the national assessment of carbon dioxide storage resources: Denver Basin, Colorado, Wyoming, and Nebraska: Chapter G in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Drake II, Ronald M.; Brennan, Sean T.; Covault, Jacob A.; Blondes, Madalyn S.; Freeman, P.A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.

2014-01-01

This is a report about the geologic characteristics of five storage assessment units (SAUs) within the Denver Basin of Colorado, Wyoming, and Nebraska. These SAUs are Cretaceous in age and include (1) the Plainview and Lytle Formations, (2) the Muddy Sandstone, (3) the Greenhorn Limestone, (4) the Niobrara Formation and Codell Sandstone, and (5) the Terry and Hygiene Sandstone Members. The described characteristics, as specified in the methodology, affect the potential carbon dioxide storage resource in the SAUs. The specific geologic and petrophysical properties of interest include depth to the top of the storage formation, average thickness, net-porous thickness, porosity, permeability, groundwater quality, and the area of structural reservoir traps. Descriptions of the SAU boundaries and the overlying sealing units are also included. Assessment results are not contained in this report; however, the geologic information included here will be used to calculate a statistical Monte Carlo-based distribution of potential storage volume in the SAUs.

Preliminary report on geophysical data in Yavapai County, Arizona

USGS Publications Warehouse

Langenheim, V.E.; Hoffmann, J.P.; Blasch, K.W.; DeWitt, Ed; Wirt, Laurie

2002-01-01

Recently acquired geophysical data provide information on the geologic framework and its effect of groundwater flow and on stream/aquifer interaction in Yavapai County, Arizona. High-resolution aeromagnetic data reflect diverse rock types at and below the topographic surface and have permitted a preliminary interpretation of faults and underlying rock types (in particular, volcanic) that will provide new insights on the geologic framework, critical input to future hydrologic investigations. Aeromagnetic data map the western end of the Bear Wallow Canyon fault into the sedimentary fill of Verde Valley. Regional gravity data indicate potentially significant accumulations of low-density basin fill in Big Chino, Verde, and Williamson Valleys. Electrical and seismic data were also collected and help evaluate the approximate depth and extent of recent alluvium overlying Tertiary and Paleozoic sediments. These data will be used to ascertain the potential contribution of shallow ground-water subflow that cannot be measured by gages or flow meters and whether stream flow in losing reaches is moving as subflow or is being lost to the subsurface. The geophysical data will help produce a more robust groundwater flow model of the region.

3D Stratigraphic Modeling of Central Aachen

NASA Astrophysics Data System (ADS)

Dong, M.; Neukum, C.; Azzam, R.; Hu, H.

2010-05-01

Since 1980s, advanced computer hardware and software technologies, as well as multidisciplinary research have provided possibilities to develop advanced three dimensional (3D) simulation software for geosciences application. Some countries, such as USA1) and Canada2) 3), have built up regional 3D geological models based on archival geological data. Such models have played huge roles in engineering geology2), hydrogeology2) 3), geothermal industry1) and so on. In cooperating with the Municipality of Aachen, the Department of Engineering Geology of RWTH Aachen University have built up a computer-based 3D stratigraphic model of 50 meter' depth for the center of Aachen, which is a 5 km by 7 km geologically complex area. The uncorrelated data from multi-resources, discontinuous nature and unconformable connection of the units are main challenges for geological modeling in this area. The reliability of 3D geological models largely depends on the quality and quantity of data. Existing 1D and 2D geological data were collected, including 1) approximately 6970 borehole data of different depth compiled in Microsoft Access database and MapInfo database; 2) a Digital Elevation Model (DEM); 3) geological cross sections; and 4) stratigraphic maps in 1m, 2m and 5m depth. Since acquired data are of variable origins, they were managed step by step. The main processes are described below: 1) Typing errors of borehole data were identified and the corrected data were exported to Variowin2.2 to distinguish duplicate points; 2) The surface elevation of borehole data was compared to the DEM, and differences larger than 3m were eliminated. Moreover, where elevation data missed, it was read from the DEM; 3) Considerable data were collected from municipal constructions, such as residential buildings, factories, and roads. Therefore, many boreholes are spatially clustered, and only one or two representative points were picked out in such areas; After above procedures, 5839 boreholes with -x, -y, -z coordinates, down-hole depth, and stratigraphic information are available. 4) We grouped stratigraphic units into four main layers based on analysis of geological settings of the modeling area. The stratigraphic units extend from Quaternary, Cretaceous, Carboniferous to Devonian. In order to facilitate the determination of each unit boundaries, a series of standard code was used to integrate data with different descriptive attributes. 5) The Quaternary and Cretaceous units are characterized by subhorizontal layers. Kriging interpolation was processed to the borehole data in order to estimate data distribution and surface relief for the layers. 6) The Carboniferous and Devonian units are folded. The lack of software support, concerning simulating folds and the shallow depth of boreholes and cross sections constrained the determination of geological boundaries. A strategy of digitalizing the fold surfaces from cross sections and establishing them as inclined strata was followed. The modeling was simply subdivided into two steps. The first step consisted of importing data into the modeling software. The second step involved the construction of subhorizontal layers and folds, which were constrained by geological maps, cross sections and outcrops. The construction of the 3D stratigraphic model is of high relevance to further simulation and application, such as 1) lithological modeling; 2) answering simple questions such as "At which unit is the water table?" and calculating volume of groundwater storage during assessment of aquifer vulnerability to contamination; and 3) assigned by geotechnical properties in grids and providing them for user required application. Acknowledgements: Borehole data is kindly provided by the Municipality of Aachen. References: 1. Janet T. Watt, Jonathan M.G. Glen, David A. John and David A. Ponce (2007) Three-dimensional geologic model of the northern Nevada rift and the Beowawe geothermal system, north-central Nevada. Geosphere, v. 3; no. 6; p. 667-682 2. Martin Ross, Michel Parent and René Lefebvre (2005) 3D geologic framework models for regional hydrogeology and land-use management: a case study from a Quaternary basin of southwestern Quebec, Canada. Hydrogeology Journal, 13:690-707 3. Martin Ross, Richard Martel, René Lefebvre, Michel Parent and Martine M. Savard (2004) Assessing rock aquifer vulnerability using downward advective times from a 3D model of surficial geology: A case study from the St. Lawrence Lowlands, Canada. Geofísica Internacional Vol. 43, Num. 4, pp. 591-602

Structural mapping from MSS-LANDSAT imagery: A proposed methodology for international geological correlation studies

NASA Technical Reports Server (NTRS)

Dejesusparada, N. (Principal Investigator); Crepani, E.; Martini, P. R.

1980-01-01

A methodology is proposed for international geological correlation studies based on LANDSAT-MSS imagery, Bullard's model of continental fit and compatible structural trends between Northeast Brazil and the West African counterpart. Six extensive lineaments in the Brazilian study area are mapped and discussed according to their regional behavior and in relation to the adjacent continental margin. Among the first conclusions, correlations were found between the Sobral Pedro II Lineament and the megafaults that surround the West African craton; and the Pernambuco Lineament with the Ngaurandere Linemanet in Cameroon. Ongoing research to complete the methodological stages includes the mapping of the West African structural framework, reconstruction of the pre-drift puzzle, and an analysis of the counterpart correlations.

Hyper-Resolution Groundwater Modeling using MODFLOW 6

NASA Astrophysics Data System (ADS)

Hughes, J. D.; Langevin, C.

2017-12-01

MODFLOW 6 is the latest version of the U.S. Geological Survey's modular hydrologic model. MODFLOW 6 was developed to synthesize many of the recent versions of MODFLOW into a single program, improve the way different process models are coupled, and to provide an object-oriented framework for adding new types of models and packages. The object-oriented framework and underlying numerical solver make it possible to tightly couple any number of hyper-resolution models within coarser regional models. The hyper-resolution models can be used to evaluate local-scale groundwater issues that may be affected by regional-scale forcings. In MODFLOW 6, hyper-resolution meshes can be maintained as separate model datasets, similar to MODFLOW-LGR, which simplifies the development of a coarse regional model with imbedded hyper-resolution models from a coarse regional model. For example, the South Atlantic Coastal Plain regional water availability model was converted from a MODFLOW-2000 model to a MODFLOW 6 model. The horizontal discretization of the original model is approximately 3,218 m x 3,218 m. Hyper-resolution models of the Aiken and Sumter County water budget areas in South Carolina with a horizontal discretization of approximately 322 m x 322 m were developed and were tightly coupled to a modified version of the original coarse regional model that excluded these areas. Hydraulic property and aquifer geometry data from the coarse model were mapped to the hyper-resolution models. The discretization of the hyper-resolution models is fine enough to make detailed analyses of the effect that changes in groundwater withdrawals in the production aquifers have on the water table and surface-water/groundwater interactions. The approach used in this analysis could be applied to other regional water availability models that have been developed by the U.S. Geological Survey to evaluate local scale groundwater issues.

Examples of Linking Codes Within GeoFramework

NASA Astrophysics Data System (ADS)

Tan, E.; Choi, E.; Thoutireddy, P.; Aivazis, M.; Lavier, L.; Quenette, S.; Gurnis, M.

2003-12-01

Geological processes usually encompass a broad spectrum of length and time scales. Traditionally, a modeling code (solver) is written to solve a problem with specific length and time scales in mind. The utility of the solver beyond the designated purpose is usually limited. Furthermore, two distinct solvers, even if each can solve complementary parts of a new problem, are difficult to link together to solve the problem as a whole. For example, Lagrangian deformation model with visco-elastoplastic crust is used to study deformation near plate boundary. Ideally, the driving force of the deformation should be derived from underlying mantle convection, and it requires linking the Lagrangian deformation model with a Eulerian mantle convection model. As our understanding of geological processes evolves, the need of integrated modeling codes, which should reuse existing codes as much as possible, begins to surface. GeoFramework project addresses this need by developing a suite of reusable and re-combinable tools for the Earth science community. GeoFramework is based on and extends Pyre, a Python-based modeling framework, recently developed to link solid (Lagrangian) and fluid (Eulerian) models, as well as mesh generators, visualization packages, and databases, with one another for engineering applications. Under the framework, a solver is aware of the existence of other solvers and can interact with each other via exchanging information across adjacent boundary. A solver needs to conform a standard interface and provide its own implementation for exchanging boundary information. The framework also provides facilities to control the coordination between interacting solvers. We will show an example of linking two solvers within GeoFramework. CitcomS is a finite element code which solves for thermal convection within a 3D spherical shell. CitcomS can solve for problems either within a full spherical (global) domain or a restricted (regional) domain of a full sphere by using different meshers. We can embed a regional CitcomS solver within a global CitcomS solver. We not that linking instances of the same solver is conceptually equivalent to linking to different solvers. The global solver has a coarser grid and a longer stable time step than the regional solver. Therefore, a global-solver time step consists of several regional-solver time steps. The time-marching scheme is described below. First, the global solver is advanced one global-solver time step. Then, the regional solver is advanced for several regional-solver time steps until it catches up global solver. Within each regional-solver time step, the velocity field of the global solver is interpolated in time and then is imposed to the regional solver as boundary conditions. Finally, the temperature field of the regional solver is extrapolated in space and is fed back to the global. These two solvers are linked and synchronized by the time-marching scheme. An effort to embed a visco-elastoplastic representation of the crust within viscous mantle flow is underway.

Stochastic modelling of non-stationary financial assets

NASA Astrophysics Data System (ADS)

Estevens, Joana; Rocha, Paulo; Boto, João P.; Lind, Pedro G.

2017-11-01

We model non-stationary volume-price distributions with a log-normal distribution and collect the time series of its two parameters. The time series of the two parameters are shown to be stationary and Markov-like and consequently can be modelled with Langevin equations, which are derived directly from their series of values. Having the evolution equations of the log-normal parameters, we reconstruct the statistics of the first moments of volume-price distributions which fit well the empirical data. Finally, the proposed framework is general enough to study other non-stationary stochastic variables in other research fields, namely, biology, medicine, and geology.

A land-use and land-cover modeling strategy to support a national assessment of carbon stocks and fluxes

USGS Publications Warehouse

Sohl, Terry L.; Sleeter, Benjamin M.; Zhu, Zhiliang; Sayler, Kristi L.; Bennett, Stacie; Bouchard, Michelle; Reker, Ryan R.; Hawbaker, Todd J.; Wein, Anne M.; Liu, Shuguang; Kanengieter, Ronald L.; Acevedo, William

2012-01-01

Changes in land use, land cover, disturbance regimes, and land management have considerable influence on carbon and greenhouse gas (GHG) fluxes within ecosystems. Through targeted land-use and land-management activities, ecosystems can be managed to enhance carbon sequestration and mitigate fluxes of other GHGs. National-scale, comprehensive analyses of carbon sequestration potential by ecosystem are needed, with a consistent, nationally applicable land-use and land-cover (LULC) modeling framework a key component of such analyses. The U.S. Geological Survey has initiated a project to analyze current and projected future GHG fluxes by ecosystem and quantify potential mitigation strategies. We have developed a unique LULC modeling framework to support this work. Downscaled scenarios consistent with IPCC Special Report on Emissions Scenarios (SRES) were constructed for U.S. ecoregions, and the FORE-SCE model was used to spatially map the scenarios. Results for a prototype demonstrate our ability to model LULC change and inform a biogeochemical modeling framework for analysis of subsequent GHG fluxes. The methodology was then successfully used to model LULC change for four IPCC SRES scenarios for an ecoregion in the Great Plains. The scenario-based LULC projections are now being used to analyze potential GHG impacts of LULC change across the U.S.

A land-use and land-cover modeling strategy to support a national assessment of carbon stocks and fluxes

USGS Publications Warehouse

Sohl, Terry L.; Sleeter, Benjamin M.; Zhu, Zhi-Liang; Sayler, Kristi L.; Bennett, Stacie; Bouchard, Michelle; Reker, Ryan R.; Hawbaker, Todd; Wein, Anne; Liu, Shu-Guang; Kanengleter, Ronald; Acevedo, William

2012-01-01

Changes in land use, land cover, disturbance regimes, and land management have considerable influence on carbon and greenhouse gas (GHG) fluxes within ecosystems. Through targeted land-use and landmanagement activities, ecosystems can be managed to enhance carbon sequestration and mitigate fluxes of other GHGs. National-scale, comprehensive analyses of carbon sequestration potential by ecosystem are needed, with a consistent, nationally applicable land-use and land-cover (LULC) modeling framework a key component of such analyses. The U.S. Geological Survey has initiated a project to analyze current and projected future GHG fluxes by ecosystem and quantify potential mitigation strategies. We have developed a unique LULC modeling framework to support this work. Downscaled scenarios consistent with IPCC Special Report on Emissions Scenarios (SRES) were constructed for U.S. ecoregions, and the FORE-SCE model was used to spatially map the scenarios. Results for a prototype demonstrate our ability to model LULC change and inform a biogeochemical modeling framework for analysis of subsequent GHG fluxes. The methodology was then successfully used to model LULC change for four IPCC SRES scenarios for an ecoregion in the Great Plains. The scenario-based LULC projections are now being used to analyze potential GHG impacts of LULC change across the U.S.

Geologic framework studies of South Carolina's Long Bay from Little River Inlet to Winyah Bay, 1999-2003: geospatial data release

USGS Publications Warehouse

Baldwin, W.E.; Denny, J.F.; Schwab, W.C.; Gayes, P.T.; Morton, R.; Driscoll, N.W.

2007-01-01

The northern South Carolina coast is a heavily developed region that supports a thriving tourism industry, large local populations and extensive infrastructure (Figure 1). The economic stability of the region is closely tied to the health of its beaches: primarily in providing support for local tourism and protection from storm events. Despite relatively low long-term shoreline erosion rates, and the implied stability of the beaches, the economic impact of storm events to coastal communities has been costly. For example, Hurricane Hugo made landfall on the central South Carolina coast in 1989. High winds and storm surge inflicted roughly $6 billion in property loss and damages, and Hugo remains the costliest storm event in South Carolina history. Localized erosion, commonly occurring around tidal inlets and erosion "hot spots", has also proved costly. Construction and maintenance of hard structures and beach nourishment, designed to mitigate the effects of erosion, have become annual or multi-annual expenditures. Providing a better understanding of the physical processes controlling coastal erosion and shoreline change will allow for more effective management of coastal resources. In 1999, the U.S. Geological Survey (USGS), in partnership with the South Carolina Sea Grant Consortium (SCSGC), began a study to investigate inner continental shelf and shoreface processes. The objectives of the USGS/SCSGC cooperative program are: 1) to provide a regional synthesis of the shallow geologic framework underlying the shoreface and inner continental shelf, and to define its role in coastal evolution and modern beach behavior; 2) to identify and model the physical processes affecting coastal ocean circulation and sediment transport, and to define their role in shaping the modern shoreline; and 3) to identify sediment sources and transport pathways in order to develop a regional sediment budget. This report contains the geospatial data used to define the geologic framework offshore of the northern South Carolina coast. The digital data presented herein accompany USGS Open-File Reports OFR 2004-1013 and OFR 2005-1345, describing the stratigraphic framework and modern sediment distribution within Long Bay, respectively. Direct on-line links to these publications are available within 'References' on the navigation bar to the left. Additional links to other publications and web sites are also available.

A 3D gravity and magnetic model for the Entenschnabel area (German North Sea)

NASA Astrophysics Data System (ADS)

Dressel, Ingo; Barckhausen, Udo; Heyde, Ingo

2018-01-01

In this study, we focus on structural configuration of the Entenschnabel area, a part of the German exclusive economic zone within the North Sea, by means of gravity and magnetic modelling. The starting point of the 3D modelling approach is published information on subseafloor structures for shallow depths, acquired by wells and seismic surveys. Subsequent gravity and magnetic modelling of the structures of the deeper subsurface builds on this geophysical and geological information and on gravity and magnetic data acquired during a research cruise to the Entenschnabel area. On the one hand, our 3D model shows the density and susceptibility distribution of the sediments and the crust. In addition, the potential field modelling provides evidence for a differentiation between lower and upper crust. The thickness distribution of the crust is also discussed with respect to the tectonic framework. Furthermore, gravity as well as magnetic modelling points to an intrusive complex beneath the Central Graben within the Entenschnabel area. On the other hand, this work provides a geological-geophysical consistent 3D gravity and magnetic model that can be used as a starting point for further investigation of this part of the German North Sea.

Science strategy for Core Science Systems in the U.S. Geological Survey, 2013-2023

USGS Publications Warehouse

Bristol, R. Sky; Euliss, Ned H.; Booth, Nathaniel L.; Burkardt, Nina; Diffendorfer, Jay E.; Gesch, Dean B.; McCallum, Brian E.; Miller, David M.; Morman, Suzette A.; Poore, Barbara S.; Signell, Richard P.; Viger, Roland J.

2012-01-01

Core Science Systems is a new mission of the U.S. Geological Survey (USGS) that grew out of the 2007 Science Strategy, “Facing Tomorrow’s Challenges: U.S. Geological Survey Science in the Decade 2007–2017.” This report describes the vision for this USGS mission and outlines a strategy for Core Science Systems to facilitate integrated characterization and understanding of the complex earth system. The vision and suggested actions are bold and far-reaching, describing a conceptual model and framework to enhance the ability of USGS to bring its core strengths to bear on pressing societal problems through data integration and scientific synthesis across the breadth of science.The context of this report is inspired by a direction set forth in the 2007 Science Strategy. Specifically, ecosystem-based approaches provide the underpinnings for essentially all science themes that define the USGS. Every point on earth falls within a specific ecosystem where data, other information assets, and the expertise of USGS and its many partners can be employed to quantitatively understand how that ecosystem functions and how it responds to natural and anthropogenic disturbances. Every benefit society obtains from the planet—food, water, raw materials to build infrastructure, homes and automobiles, fuel to heat homes and cities, and many others, are derived from or effect ecosystems.The vision for Core Science Systems builds on core strengths of the USGS in characterizing and understanding complex earth and biological systems through research, modeling, mapping, and the production of high quality data on the nation’s natural resource infrastructure. Together, these research activities provide a foundation for ecosystem-based approaches through geologic mapping, topographic mapping, and biodiversity mapping. The vision describes a framework founded on these core mapping strengths that makes it easier for USGS scientists to discover critical information, share and publish results, and identify potential collaborations that transcend all USGS missions. The framework is designed to improve the efficiency of scientific work within USGS by establishing a means to preserve and recall data for future applications, organizing existing scientific knowledge and data to facilitate new use of older information, and establishing a future workflow that naturally integrates new data, applications, and other science products to make it easier and more efficient to conduct interdisciplinary research over time. Given the increasing need for integrated data and interdisciplinary approaches to solve modern problems, leadership by the Core Science Systems mission will facilitate problem solving by all USGS missions in ways not formerly possible.The report lays out a strategy to achieve this vision through three goals with accompanying objectives and actions. The first goal builds on and enhances the strengths of the Core Science Systems mission in characterizing and understanding the earth system from the geologic framework to the topographic characteristics of the land surface and biodiversity across the nation. The second goal enhances and develops new strengths in computer and information science to make it easier for USGS scientists to discover data and models, share and publish results, and discover connections between scientific information and knowledge. The third goal brings additional focus to research and development methods to address complex issues affecting society that require integration of knowledge and new methods for synthesizing scientific information. Collectively, the report lays out a strategy to create a seamless connection between all USGS activities to accelerate and make USGS science more efficient by fully integrating disciplinary expertise within a new and evolving science paradigm for a changing world in the 21st century.

The inventory of the Portuguese geological heritage: a good example of scientific cooperation between universities

NASA Astrophysics Data System (ADS)

Pereira, P.; Brilha, J.; Pereira, D.

2012-04-01

Initiatives of identification, protection, and valuation of the Portuguese abiotic natural heritage have been carried out mainly by the scientific community, and particularly by the academic community. The official institutions responsible for nature conservation have focused their policies primarily on biodiversity issues and the relevance of geoconservation in the Portuguese geological survey was always minor, compared with homologous institutions from countries like Spain, for example. In this context, the academic community has led geoconservation research and activities in Portugal, especially since the late 1990s, following the development of this theme in the European continent. The first systematic inventory of the Portuguese geological heritage is a clear example of the academic collaboration that characterizes the geoconservation in Portugal. Three hundred and twenty six geosites with international or national relevance have been inventoried under the scope of the scientific research project "Identification, characterisation and conservation of geological heritage: a geoconservation strategy for Portugal", financed by the Portuguese Foundation for Science and Technology between 2007 and 2010 (PTDC/CTE-GEX/64966/2006). The inventory (one of the project's outputs) was coordinated by the University of Minho team with the participation of the universities of Algarve, Aveiro, Azores, Coimbra, Évora, Lisboa, Madeira, Nova de Lisboa, Porto, and Trás-os-Montes e Alto Douro. The inventory procedures were based on the ProGEO methodology, i.e., definition of geological frameworks followed by the identification of representative geosites with national and international relevance for each framework. The geosites were selected exclusively based on their scientific value and support twenty-seven frameworks. For each geological framework a leading geoscientist from a university was responsible for the scientific characterization of the framework, to invite collaborators to identify representative geosites, and to assess the scientific value and vulnerability of the geosites. In the end, seventy geoscientists, mainly from universities, took part in the scientific results that are now important raw data to support nature conservation initiatives. The inventory will integrate the natural heritage database (SIPNAT) under the responsibility of the Institute of Nature Conservation and Biodiversity (ICNB), as expected in the Portuguese legislation for nature conservation (DL 142/2008) and established in a protocol signed between the ICNB and the University of Minho.

Geophysical identification and geological Implications of the Southern Alaska Magnetic Trough

USGS Publications Warehouse

Saltus, R.W.; Hudson, T.L.; Wilson, Frederic H.

2003-01-01

The southern Alaska magnetic trough (SAMT) is one of the fundamental, crustal-scale, magnetic features of Alaska. It is readily recognized on 10 km upward-continued aeromagnetic maps of the state. The arcuate SAMT ranges from 30 to 100 km wide and extends in two separate segments along the southern Alaska margin for about 1200 km onshore (from near the Alaska/Canada border at about 60 degrees north latitude to the Bering Sea) and may continue an additional 500 km or more offshore (in the southern Bering Sea). The SAMT is bordered to the south by the southern Alaska magnetic high (SAMH) produced by strongly magnetic crust and to the north by a magnetically quiet zone that reflects weakly magnetic interior Alaska crust. Geophysically, the SAMT is more than just the north-side dipole low associated with the SAMH. Several modes of analysis, including examination of magnetic potential (pseudogravity) and profile modeling, indicate that the source of this magnetic trough is a discrete, crustal-scale body. Geologically, the western portion of the SAMT coincides to a large degree with collapsed Mesozoic Kahiltna flysch basin. This poster presents our geophysical evidence for the extent and geometry of this magnetic feature as well as initial geological synthesis and combined geologic/geophysical modeling to examine the implications of this feature for the broad scale tectonic framework of southern Alaska.

Extension of the Cerro Prieto field and zones in the Mexicali Valley with geothermal possibilities in the future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fonseca L, H.L.; de la Pena L, A.; Puente C, I.

This study concerns the possible extension of the Cerro Prieto field and identification of other zones in the Mexicali Valley with geothermal development potential by assessing the structural geologic conditions in relation to the regional tectonic framework and the integration of geologic and geophysical surveys carried out at Cerro Prieto. This study is based on data obtained from the wells drilled to date and the available geological and geophysical information. With this information, a geologic model of the field is developed as a general description of the geometry of what might be the geothermal reservoir of the Cerro Prieto field.more » In areas with geothermal potential within the Mexicali Valley, the location of irrigation wells with anomalous temperatures was taken as a point of departure for subsequent studies. Based on this initial information, gravity and magnetic surveys were made, followed by seismic reflection and refraction surveys and the drilling of 1200-m-deep multiple-use wells. Based on the results of the final integration of these studies with the geology of the region, it is suggested that the following areas should be explored further: east of Cerro Prieto, Tulecheck, Riito, Aeropuerto-Algodones, and San Luis Rio Colorado, Sonora.« less

Structural geology practice and learning, from the perspective of cognitive science

NASA Astrophysics Data System (ADS)

Shipley, Thomas F.; Tikoff, Basil; Ormand, Carol; Manduca, Cathy

2013-09-01

Spatial ability is required by practitioners and students of structural geology and so, considering spatial skills in the context of cognitive science has the potential to improve structural geology teaching and practice. Spatial thinking skills may be organized using three dichotomies, which can be linked to structural geology practice. First, a distinction is made between separating (attending to part of a whole) and combining (linking together aspects of the whole). While everyone has a basic ability to separate and combine, experts attend to differences guided by experiences of rock properties in context. Second, a distinction is made between seeing the relations among multiple objects as separate items or the relations within a single object with multiple parts. Experts can flexibly consider relations among or between objects to optimally reason about different types of spatial problems. Third, a distinction is made between reasoning about stationary and moving objects. Experts recognize static configurations that encode a movement history, and create mental models of the processes that led to the static state. The observations and inferences made by a geologist leading a field trip are compared with the corresponding observations and inferences made by a cognitive psychologist interested in spatial learning. The presented framework provides a vocabulary for discussing spatial skills both within and between the fields of structural geology and cognitive psychology.

Geologic framework for the national assessment of carbon dioxide storage resources: Williston Basin, Central Montana Basins, and Montana Thrust Belt study areas: Chapter J in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Buursink, Marc L.; Merrill, Matthew D.; Craddock, William H.; Roberts-Ashby, Tina L.; Brennan, Sean T.; Blondes, Madalyn S.; Freeman, P.A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2014-01-01

Figures in this report show the study area boundaries along with the SAU extent and cell maps of well penetrations through sealing units into the top of the storage formations. The USGS does not necessarily know the location of all wells and cannot guarantee the full extent of drilling through specific formations in any given cell shown on the cell maps.

Stratigraphic framework of Cambrian and Ordovician rocks in the central Appalachian basin from Campbell County, Kentucky, to Tazewell County, Virginia: Chapter E.2.4 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ryder, Robert T.; Repetski, John E.; Harris, Anita G.; Lentz, Erika E.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

This chapter is a re-release of U.S. Geological Survey Miscellaneous Investigations Series Map I-2530, of the same title, by Ryder and others (1997; online version 2.0 revised and digitized by Erika E. Lentz, 2004). Version 2.0 is a digital version of the original and also includes the gamma-ray well log traces.

Potential Field Modeling at Global to Prospect Scales - Adding Value to the Geological, Seismic, Gravity, Magnetic and Rock Property Datasets of Australia

NASA Astrophysics Data System (ADS)

Lane, R. J. L.

2015-12-01

At Geoscience Australia, we are upgrading our gravity and magnetic modeling tools to provide new insights into the composition, properties, and structure of the subsurface. The scale of the investigations varies from the size of tectonic plates to the size of a mineral prospect. To accurately model potential field data at all of these scales, we require modeling software that can operate in both spherical and Cartesian coordinate frameworks. The models are in the form of a mesh, with spherical prismatic (tesseroid) elements for spherical coordinate models of large volumes, and rectangular prisms for smaller volumes evaluated in a Cartesian coordinate framework. The software can compute the forward response of supplied rock property models and can perform inversions using constraints that vary from weak generic smoothness through to very specific reference models compiled from various types of "hard facts" (i.e., surface mapping, drilling information, crustal seismic interpretations). To operate efficiently, the software is being specifically developed to make use of the resources of the National Computational Infrastructure (NCI) at the Australian National University (ANU). The development of these tools is been carried out in collaboration with researchers from the Colorado School of Mines (CSM) and the China University of Geosciences (CUG) and is at the stage of advanced testing. The creation of individual 3D geological models will provide immediate insights. Users will also be able to combine models, either by stitching them together or by nesting smaller and more detailed models within a larger model. Comparison of the potential field response of a composite model with the observed fields will give users a sense of how comprehensively these models account for the observations. Users will also be able to model the residual fields (i.e., the observed minus calculated response) to discover features that are not represented in the input composite model.

The DeepMIP Contribution to PMIP4: Experimental Design for Model Simulations of the EECO, PETM, and pre-PETM (version 1.0)

NASA Technical Reports Server (NTRS)

Lunt, Daniel J.; Huber, Matthew; Anagnostou, Eleni; Baatsen, Michiel L. J.; Caballero, Rodrigo; DeConto, Rob; Dijkstra, Henk A.; Donnadieu, Yannick; Evans, David; Feng, Ran;

Integration of seismic-reflection and well data to assess the potential impact of stratigraphic and structural features on sustainable water supply from the Floridan aquifer system, Broward County, Florida

USGS Publications Warehouse

Cunningham, Kevin J.

2014-01-01

The U.S. Geological Survey and Broward County water managers commenced a 3.5-year cooperative study in July 2012 to refine the geologic and hydrogeologic framework of the Floridan aquifer system (FAS) in Broward County. A lack of advanced stratigraphic knowledge of the physical system and structural geologic anomalies (faults and fractures originating from tectonics and karst-collapse structures) within the FAS pose a risk to the sustainable management of the resource. The principal objective of the study is to better define the regional stratigraphic and structural setting of the FAS in Broward County. The objective will be achieved through the acquisition, processing, and interpretation of new seismic-reflection data along several canals in Broward County. The interpretation includes integration of the new seismic-reflection data with existing seismic-reflection profiles along Hillsboro Canal in Broward County and within northeast Miami-Dade County, as well as with data from nearby FAS wellbores. The scope of the study includes mapping the geologic, hydrogeologic, and seismic-reflection framework of the FAS, and identifying stratigraphic and structural characteristics that could either facilitate or preclude the sustainable use of the FAS as an alternate water supply or a treated effluent repository. In addition, the investigation offers an opportunity to: (1) improve existing groundwater flow models, (2) enhance the understanding of the sensitivity of the groundwater system to well-field development and upconing of saline fluids, and (3) support site selection for future FAS projects, such as Class I wells that would inject treated effluent into the deep Boulder Zone.

Study of a prehistoric landslide using seismic reflection methods integrated with geological data in the Wasatch Mountains, Utah, USA

USGS Publications Warehouse

Tingey, B.E.; McBride, J.H.; Thompson, T.J.; Stephenson, W.J.; South, J.V.; Bushman, M.

2007-01-01

An integration of geological and geophysical techniques characterizes the internal and basal structure of a landslide along the western margin of the Wasatch Mountains in northern Utah, USA. The study area is within a region of planned and continuing residential development. The Little Valley Landslide is a prehistoric landslide as old as 13??ka B.P. Drilling and trenching at the site indicate that the landslide consists of chaotic and disturbed weathered volcanic material derived from Tertiary age volcanic rocks that comprise a great portion of the Wasatch Range. Five short high-resolution common mid-point seismic reflection profiles over selected portions of the site examine the feasibility of using seismic reflection to study prehistoric landslides in the Wasatch Mountain region. Due to the expected complexity of the near-surface geology, we have pursued an experimental approach in the data processing, examining the effects of muting first arrivals, frequency filtering, model-based static corrections, and seismic migration. The results provide a framework for understanding the overall configuration of the landslide, its basal (failure) surface, and the structure immediately underlying this surface. A glide surface or de??collement is interpreted to underlie the landslide suggesting a large mass movement. The interpretation of a glide surface is based on the onset of coherent reflectivity, calibrated by information from a borehole located along one of the seismic profiles. The glide surface is deepest in the center portion of the landslide and shallows up slope, suggesting a trough-like feature. This study shows that seismic reflection techniques can be successfully used in complex alpine landslide regions to (1) provide a framework in which to link geological data and (2) reduce the need for an extensive trenching and drilling program. ?? 2007 Elsevier B.V. All rights reserved.

Geophysical Framework Investigations Influencing Ground-Water Resources in East-Central Nevada and West-Central Utah

USGS Publications Warehouse

Watt, Janet T.; Ponce, David A.

2007-01-01

A geophysical investigation was undertaken as part of an effort to characterize the geologic framework influencing ground-water resources in east-central Nevada and west-central Utah. New gravity data were combined with existing aeromagnetic, drill-hole, and geologic data to help determine basin geometry, infer structural features, estimate depth to pre-Cenozoic basement rocks, and further constrain the horizontal extents of exposed and buried plutons. In addition, a three-dimensional (3D) geologic model was constructed to help illustrate the often complex geometries of individual basins and aid in assessing the connectivity of adjacent basins. In general, the thirteen major valleys within the study area have axes oriented north-south and frequently contain one or more sub-basins. These basins are often asymmetric and typically reach depths of 2 km. Analysis of gravity data helped delineate geophysical lineaments and accommodation zones. Structural complexities may further compartmentalize ground-water flow within basins and the influence of tectonics on basin sedimentation further complicates their hydrologic properties. The horizontal extent of exposed and, in particular, buried plutons was estimated over the entire study area. The location and subsurface extents of these plutons will be very important for regional water resource assessments, as these features may act as either barriers or pathways for groundwater flow. A previously identified basement gravity low strikes NW within the study area and occurs within a highly extended terrane between the Butte and Confusion synclinoria. Evidence from geophysical, geologic, and seismic reflection data suggests relatively lower density plutonic rocks may extend to moderate crustal depths and rocks of similar composition may be the source of the entire basement gravity anomaly.

Geologic Cross Section I–I′ Through the Appalachian Basin from the Eastern Margin of the Illinois Basin, Jefferson County, Kentucky, to the Valley and Ridge Province, Scott County, Virginia

USGS Publications Warehouse

Ryder, Robert T.; Trippi, Michael H.; Swezey, Christopher S.

2015-12-08

Cross section I‒I ’ contains much information that is useful for evaluating energy resources in the Appalachian basin. Many of the key elements of the Appalachian basin petroleum systems (such as source rocks, reservoir rocks, seals, and traps) can be inferred from lithologic units, unconformities, and geologic structures shown on the cross section. Other aspects of petroleum systems (such as the timing of petroleum generation and petroleum migration pathways) may be evaluated by burial history, thermal history, and fluid flow models on the basis of what is shown on the cross section. Cross section I‒I’ also provides a stratigraphic and structural framework for the Pennsylvanian coal-bearing section. In addition, geologists and engineers could use cross section I‒I’ as a reconnaissance tool to identify plausible geologic structures and strata for the subsurface storage of liquid waste or for the sequestration of carbon dioxide.

Integrated characterization of the geologic framework of a contaminated site in West Trenton, New Jersey

USGS Publications Warehouse

Ellefsen, Karl J.; Burton, William C.; Lacombe, Pierre J.

2012-01-01

Fractured sedimentary bedrock and groundwater at the former Naval Air Warfare Center in West Trenton, New Jersey (United States of America) are contaminated with chlorinated solvents. Predicting contaminant migration or removing the contaminants requires an understanding of the geology. Consequently, the geologic framework near the site was characterized with four different methods having different spatial scales: geologic field mapping, analyses of bedrock drill core, analyses of soil and regolith, and S-wave refraction surveys. A fault zone is in the southeast corner of the site and separates two distinct sedimentary formations; the fault zone dips (steeply) southeasterly, strikes northeasterly, and extends at least 550 m along its strike direction. Drill core from the fault zone is extensively brecciated and includes evidence of tectonic contraction. Approximately 300 m east of this fault zone is another fault zone, which offsets the contact between the two sedimentary formations. The S-wave refraction surveys identified both fault zones beneath soil and regolith and thereby provided constraints on their lateral extent and location.

Geologic studies in Alaska by the U.S. Geological Survey, 1997

USGS Publications Warehouse

Kelley, Karen D.

1999-01-01

Geologic Framework studies provide background information that is the scientific basis for present and future studies of the environment, mineral and energy resources, paleoclimate, and hazards in Alaska. One paper presents the results of sedimentologic and paleontologic comparisons of lower Paleozoic, deep-water-facies rock units in central Alaska (Dumoulin and others). The authors show which of these units are likely to correlate with one another, suggest likely source regions, and provide a structural restoration of units that have been fragmented by large fault motions. A second framework paper provides a map, rock descriptions, and chemical compositions of volcanic rocks in a newly recognized, geologically young volcanic center in the Aleutian volcanic arc (Hildreth and others). A third paper presents an interesting summary of gravity changes that occurred in south-central Alaska during the great earthquake of 1964 and for the following 25 years (Barnes). Gravity changes correlate with land-elevation changes in some cases, but not in others, which means that different processes are responsible for the gravity changes.

3D geological modelling and geothermal mapping - the first results of the transboundary Polish - Saxon project "TransGeoTherm"

NASA Astrophysics Data System (ADS)

Kozdrój, Wiesław; Kłonowski, Maciej; Mydłowski, Adam; Ziółkowska-Kozdrój, Małgorzata; Badura, Janusz; Przybylski, Bogusław; Russ, Dorota; Zawistowski, Karol; Domańska, Urszula; Karamański, Paweł; Krentz, Ottomar; Hofmann, Karina; Riedel, Peter; Reinhardt, Silke; Bretschneider, Mario

2014-05-01

TransGeoTherm is a common project of the Polish Geological Institute - National Research Institute Lower Silesian Branch (Lead Partner) and the Saxon State Agency for Environment, Agriculture and Geology, co-financed by the European Union (EU) under the framework of the Operational Programme for Transboundary Co-operation Poland-Saxony 2007-2013. It started in October 2012 and will last until June 2014. The main goal of the project is to introduce and establish the use of low temperature geothermal energy as a low emission energy source in the Saxon-Polish transboundary project area. The numerous geological, hydrogeological and geothermal data have been gathered, analysed, combined and interpreted with respect to 3D numerical modelling and subsequently processed with use of the GOCAD software. The resulting geological model covers the transboundary project area exceeding 1.000 km2 and comprises around 70 units up to the depth of about 200 metres (locally deeper) below the terrain. The division of the above units has been based on their litho-stratigraphy as well as geological, hydrogeological and geothermal settings. The model includes two lignite deposits: Berzdorf deposit in Saxony-mined out and already recultivated and Radomierzyce deposit in Poland - documented but still not excavated. At the end of the modelling procedure the raster data sets of the top, bottom and thickness of every unit will be deduced from the 3D geological model with a gridsize of 25 by 25 metres. Based on the geothermal properties of the rocks and their groundwater content a specific value of geothermal conductivity will be allocated to each layer of every borehole. Thereafter for every section of a borehole, belonging to a certain unit of the 3D geological model, a weighted mean value will be calculated. Next the horizontal distribution of these values within every unit will be interpolated. This step / procedure has to be done for all units. As a result of further calculations a series of maps showing the geothermal conditions for the selected depths of 40, 70, 100 and 130 metres below the terrain will be elaborated and made available via the Internet. The prospective final users of the project results will be the local and regional authorities, inhabitants, engineers, etc. The project will provide information and data which are important for local and regional planning and development - on the one hand the maps will provide information on possibilities using locations for low temperature geothermal heating and cooling, while on the other hand they are needed to setup and dimension the geothermal installations in detail.

Geophysical framework of the southwestern Nevada volcanic field and hydrogeologic implications

USGS Publications Warehouse

Grauch, V.J.; Sawyer, David A.; Fridrich, Chris J.; Hudson, Mark R.

1999-01-01

Gravity and magnetic data, when integrated with other geophysical, geological, and rock-property data, provide a regional framework to view the subsurface geology in the southwestern Nevada volcanic field. The region has been loosely divided into six domains based on structural style and overall geophysical character. For each domain, the subsurface tectonic and magmatic features that have been inferred or interpreted from previous geophysical work has been reviewed. Where possible, abrupt changes in geophysical fields as evidence for potential structural lithologic control on ground-water flow has been noted. Inferred lithology is used to suggest associated hydrogeologic units in the subsurface. The resulting framework provides a basis for investigators to develop hypotheses from regional ground-water pathways where no drill-hole information exists.

Relationship between geohydrology and Upper Pleistocene-Holocene evolution of the eastern region of the Province of Buenos Aires, Argentina

NASA Astrophysics Data System (ADS)

Capítulo, Leandro Rodrigues; Kruse, Eduardo E.

2017-07-01

The Upper Pleistocene-Holocene geological evolution, which is characterized by its landscape-forming energy and is related to geological and geomorphological complexity, has an impact on the groundwater dynamics of coastal aquifers. The geological configuration of a sector of the east coast of the Province of Buenos Aires was analyzed, as well as its connection with the geological and geomorphological history of the region during the Late Pleistocene and Holocene, and its influence on the regional and local geohydrological behaviour. This analysis was based on the application of the concept of hydrofacies. Boreholes were drilled and sampled (with depths of up to 40 m), and vertical electrical sounding, electrical tomography and pumping tests were undertaken. The description of the cutting samples by means of a stereo microscope, the interpretation of satellite images, and the construction of lithological and hydrogeological profiles and flow charts were carried out in the laboratory, and then integrated in a GIS. The identification of the lithological units and their distribution in the area allowed the construction of an evolutionary geological model for the Late Pleistocene and Holocene. Three aquifer units can be recognized: one of Late Pleistocene age (hydrofacies E) and the other two of Holocene age (hydrofacies A and C); their hydraulic connection depends on the occurrence and thickness variation of the aquitard units (hydrofacies B and D). The approach adopted allows the examination of the possibilities for groundwater exploitation and constitutes an applied conceptual framework to be taken into consideration when developing conceptual and numerical models at the local and regional scales.

Final Report: Optimal Model Complexity in Geological Carbon Sequestration: A Response Surface Uncertainty Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Ye

The critical component of a risk assessment study in evaluating GCS is an analysis of uncertainty in CO2 modeling. In such analyses, direct numerical simulation of CO2 flow and leakage requires many time-consuming model runs. Alternatively, analytical methods have been developed which allow fast and efficient estimation of CO2 storage and leakage, although restrictive assumptions on formation rock and fluid properties are employed. In this study, an intermediate approach is proposed based on the Design of Experiment and Response Surface methodology, which consists of using a limited number of numerical simulations to estimate a prediction outcome as a combination ofmore » the most influential uncertain site properties. The methodology can be implemented within a Monte Carlo framework to efficiently assess parameter and prediction uncertainty while honoring the accuracy of numerical simulations. The choice of the uncertain properties is flexible and can include geologic parameters that influence reservoir heterogeneity, engineering parameters that influence gas trapping and migration, and reactive parameters that influence the extent of fluid/rock reactions. The method was tested and verified on modeling long-term CO2 flow, non-isothermal heat transport, and CO2 dissolution storage by coupling two-phase flow with explicit miscibility calculation using an accurate equation of state that gives rise to convective mixing of formation brine variably saturated with CO2. All simulations were performed using three-dimensional high-resolution models including a target deep saline aquifer, overlying caprock, and a shallow aquifer. To evaluate the uncertainty in representing reservoir permeability, sediment hierarchy of a heterogeneous digital stratigraphy was mapped to create multiple irregularly shape stratigraphic models of decreasing geologic resolutions: heterogeneous (reference), lithofacies, depositional environment, and a (homogeneous) geologic formation. To ensure model equivalency, all the stratigraphic models were successfully upscaled from the reference heterogeneous model for bulk flow and transport predictions (Zhang & Zhang, 2015). GCS simulation was then simulated with all models, yielding insights into the level of parameterization complexity that is needed for the accurate simulation of reservoir pore pressure, CO2 storage, leakage, footprint, and dissolution over both short (i.e., injection) and longer (monitoring) time scales. Important uncertainty parameters that impact these key performance metrics were identified for the stratigraphic models as well as for the heterogeneous model, leading to the development of reduced/simplified models at lower characterization cost that can be used for the reservoir uncertainty analysis. All the CO2 modeling was conducted using PFLOTRAN – a massively parallel, multiphase, multi-component, and reactive transport simulator developed by a multi-laboratory DOE/SciDAC (Scientific Discovery through Advanced Computing) project (Zhang et al., 2017, in review). Within the uncertainty analysis framework, increasing reservoir depth were investigated to explore its effect on the uncertainty outcomes and the potential for developing gravity-stable injection with increased storage security (Dai et al., 20126; Dai et al., 2017, in review). Finally, to accurately model CO2 fluid-rock reactions and resulting long-term storage as secondary carbonate minerals, a modified kinetic rate law for general mineral dissolution and precipitation was proposed and verified that is invariant to a scale transformation of the mineral formula weight. This new formulation will lead to more accurate assessment of mineral storage over geologic time scales (Lichtner, 2016).« less

Death Valley regional groundwater flow system, Nevada and California-Hydrogeologic framework and transient groundwater flow model

USGS Publications Warehouse

Belcher, Wayne R.; Sweetkind, Donald S.

2010-01-01

A numerical three-dimensional (3D) transient groundwater flow model of the Death Valley region was developed by the U.S. Geological Survey for the U.S. Department of Energy programs at the Nevada Test Site and at Yucca Mountain, Nevada. Decades of study of aspects of the groundwater flow system and previous less extensive groundwater flow models were incorporated and reevaluated together with new data to provide greater detail for the complex, digital model. A 3D digital hydrogeologic framework model (HFM) was developed from digital elevation models, geologic maps, borehole information, geologic and hydrogeologic cross sections, and other 3D models to represent the geometry of the hydrogeologic units (HGUs). Structural features, such as faults and fractures, that affect groundwater flow also were added. The HFM represents Precambrian and Paleozoic crystalline and sedimentary rocks, Mesozoic sedimentary rocks, Mesozoic to Cenozoic intrusive rocks, Cenozoic volcanic tuffs and lavas, and late Cenozoic sedimentary deposits of the Death Valley regional groundwater flow system (DVRFS) region in 27 HGUs. Information from a series of investigations was compiled to conceptualize and quantify hydrologic components of the groundwater flow system within the DVRFS model domain and to provide hydraulic-property and head-observation data used in the calibration of the transient-flow model. These studies reevaluated natural groundwater discharge occurring through evapotranspiration (ET) and spring flow; the history of groundwater pumping from 1913 through 1998; groundwater recharge simulated as net infiltration; model boundary inflows and outflows based on regional hydraulic gradients and water budgets of surrounding areas; hydraulic conductivity and its relation to depth; and water levels appropriate for regional simulation of prepumped and pumped conditions within the DVRFS model domain. Simulation results appropriate for the regional extent and scale of the model were provided by acquiring additional data, by reevaluating existing data using current technology and concepts, and by refining earlier interpretations to reflect the current understanding of the regional groundwater flow system. Groundwater flow in the Death Valley region is composed of several interconnected, complex groundwater flow systems. Groundwater flow occurs in three subregions in relatively shallow and localized flow paths that are superimposed on deeper, regional flow paths. Regional groundwater flow is predominantly through a thick Paleozoic carbonate rock sequence affected by complex geologic structures from regional faulting and fracturing that can enhance or impede flow. Spring flow and ET are the dominant natural groundwater discharge processes. Groundwater also is withdrawn for agricultural, commercial, and domestic uses. Groundwater flow in the DVRFS was simulated using MODFLOW-2000, the U.S. Geological Survey 3D finitedifference modular groundwater flow modeling code that incorporates a nonlinear least-squares regression technique to estimate aquifer parameters. The DVRFS model has 16 layers of defined thickness, a finite-difference grid consisting of 194 rows and 160 columns, and uniform cells 1,500 meters (m) on each side. Prepumping conditions (before 1913) were used as the initial conditions for the transient-state calibration. The model uses annual stress periods with discrete recharge and discharge components. Recharge occurs mostly from infiltration of precipitation and runoff on high mountain ranges and from a small amount of underflow from adjacent basins. Discharge occurs primarily through ET and spring discharge (both simulated as drains) and water withdrawal by pumping and, to a lesser amount, by underflow to adjacent basins simulated by constant-head boundaries. All parameter values estimated by the regression are reasonable and within the range of expected values. The simulated hydraulic heads of the final calibrated transient mode

Coupling machine learning with mechanistic models to study runoff production and river flow at the hillslope scale

NASA Astrophysics Data System (ADS)

Marçais, J.; Gupta, H. V.; De Dreuzy, J. R.; Troch, P. A. A.

2016-12-01

Geomorphological structure and geological heterogeneity of hillslopes are major controls on runoff responses. The diversity of hillslopes (morphological shapes and geological structures) on one hand, and the highly non linear runoff mechanism response on the other hand, make it difficult to transpose what has been learnt at one specific hillslope to another. Therefore, making reliable predictions on runoff appearance or river flow for a given hillslope is a challenge. Applying a classic model calibration (based on inverse problems technique) requires doing it for each specific hillslope and having some data available for calibration. When applied to thousands of cases it cannot always be promoted. Here we propose a novel modeling framework based on coupling process based models with data based approach. First we develop a mechanistic model, based on hillslope storage Boussinesq equations (Troch et al. 2003), able to model non linear runoff responses to rainfall at the hillslope scale. Second we set up a model database, representing thousands of non calibrated simulations. These simulations investigate different hillslope shapes (real ones obtained by analyzing 5m digital elevation model of Brittany and synthetic ones), different hillslope geological structures (i.e. different parametrizations) and different hydrologic forcing terms (i.e. different infiltration chronicles). Then, we use this model library to train a machine learning model on this physically based database. Machine learning model performance is then assessed by a classic validating phase (testing it on new hillslopes and comparing machine learning with mechanistic outputs). Finally we use this machine learning model to learn what are the hillslope properties controlling runoffs. This methodology will be further tested combining synthetic datasets with real ones.

Coal assessments and coal research in the Appalachian basin: Chapter D.4 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Tewalt, Susan J.; Ruppert, Leslie F.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

State geological surveys are concentrating on mapping and correlating coal beds and coal zones and studying CBM potential and production. Both State surveys and the USGS are researching the potential for carbon dioxide sequestration in unmined coal beds and other geologic reservoirs. In addition, the State geological surveys continue their long-term collaboration with the USGS and provide coal stratigraphic data to the National Coal Resources Data System (NCRDS).

Voxel modelling of sands and gravels of Pleistocene Rhine and Meuse deposits in Flanders (Belgium)

NASA Astrophysics Data System (ADS)

van Haren, Tom; Dirix, Katrijn; De Koninck, Roel

2017-04-01

Voxel modelling or 3D volume modelling of Quaternary raw materials is VITO's next step in the geological layer modelling of the Flanders and Brussels Capital Region in Belgium (G3D - Matthijs et al., 2013). The aim is to schematise deposits as voxels ('volumetric pixels') that represent lithological information on a grid in three-dimensional space (25 x 25 x 0.5 m). A new voxel model on Pleistocene Meuse and Rhine sands and gravels will be illustrated succeeding a voxel model on loess resources (van Haren et al., 2016). The model methodology is based on a geological 'skeleton' extracted from the regional geological layer model of Flanders. This framework holds the 3D interpolated lithological information of 5.000 boreholes. First a check on quality and spatial location filtered out significant and usable lithological information. Subsequently a manual geological interpretation was performed to analyse stratigraphical arrangement and identify the raw materials of interest. Finally, a workflow was developed that automatically encodes and classifies the borehole descriptions in a standardized manner. This workflow was implemented by combining Microsoft Access® and ArcMap® and is able to convert borehole descriptions into specific geological parameters. An analysis of the conversed lithological data prior to interpolation improves the understanding of the spatial distribution, to fine tune the modelling process and to know the limitations of the data. The converted lithological data were 3D interpolated in Voxler using IDW and resulted in a model containing 52 million voxels. It gives an overview on the regional distribution and thickness variation of interesting Pleistocene aggregates of Meuse and Rhine. Much effort has been put in setting up a database structure in Microsoft Access® and Microsoft SQL Server® in order to arrange and analyse the lithological information, link the voxel model with the geological layer model and handle and analyse the resulting voxelmodel data. The database structure allows to analyse and set certain preconditions (minimal thickness or maximum depth of aggregates, maximum thickness of intercalating clays) on the model in order to calculate and view distributions of deposits which meet these preconditions. These results are interesting for pre-prospective purposes, illustrating the distribution of lithological information and making the end user more aware of the potential economic value of the subsurface. References van Haren T. et al (2016) - An interactive voxel model for mineral resources: loess deposits in Flanders (Belgium). Zeitschrift der Deutschen Gesellschaft für Geowissenschaften, Volume 167, Number 4, pp. 363-376(14). Matthijs J. et al. (2013) - Geological 3D layer model of the Flanders Region and Brussels-Capital Region - 2nd version. Study performed in order of the Ministery of the Flemish Community. VITO report 2013/R/ETE/43, 24p. (in Dutch)

Estimating and mapping ecological processes influencing microbial community assembly

PubMed Central

Stegen, James C.; Lin, Xueju; Fredrickson, Jim K.; Konopka, Allan E.

2015-01-01

Ecological community assembly is governed by a combination of (i) selection resulting from among-taxa differences in performance; (ii) dispersal resulting from organismal movement; and (iii) ecological drift resulting from stochastic changes in population sizes. The relative importance and nature of these processes can vary across environments. Selection can be homogeneous or variable, and while dispersal is a rate, we conceptualize extreme dispersal rates as two categories; dispersal limitation results from limited exchange of organisms among communities, and homogenizing dispersal results from high levels of organism exchange. To estimate the influence and spatial variation of each process we extend a recently developed statistical framework, use a simulation model to evaluate the accuracy of the extended framework, and use the framework to examine subsurface microbial communities over two geologic formations. For each subsurface community we estimate the degree to which it is influenced by homogeneous selection, variable selection, dispersal limitation, and homogenizing dispersal. Our analyses revealed that the relative influences of these ecological processes vary substantially across communities even within a geologic formation. We further identify environmental and spatial features associated with each ecological process, which allowed mapping of spatial variation in ecological-process-influences. The resulting maps provide a new lens through which ecological systems can be understood; in the subsurface system investigated here they revealed that the influence of variable selection was associated with the rate at which redox conditions change with subsurface depth. PMID:25983725

‘Cape capture’: Geologic data and modeling results suggest the Holocene loss of a Carolina Cape

USGS Publications Warehouse

Thieler, E. Robert; Ashton, Andrew D.

2011-01-01

For more than a century, the origin and evolution of the set of cuspate forelands known as the Carolina Capes—Hatteras, Lookout, Fear, and Romain—off the eastern coast of the United States have been discussed and debated. The consensus conceptual model is not only that these capes existed through much or all of the Holocene transgression, but also that their number has not changed. Here we describe bathymetric, lithologic, seismic, and chronologic data that suggest another cape may have existed between Capes Hatteras and Lookout during the early to middle Holocene. This cape likely formed at the distal end of the Neuse-Tar-Pamlico fluvial system during the early Holocene transgression, when this portion of the shelf was flooded ca. 9 cal (calibrated) kyr B.P., and was probably abandoned by ca. 4 cal kyr B.P., when the shoreline attained its present general configuration. Previously proposed mechanisms for cape formation suggest that the large-scale, rhythmic pattern of the Carolina Capes arose from a hydrodynamic template or the preexisting geologic framework. Numerical modeling, however, suggests that the number and spacing of capes can be dynamic, and that a coast can self-organize in response to a high-angle-wave instability in shoreline shape. In shoreline evolution model simulations, smaller cuspate forelands are subsumed by larger neighbors over millennial time scales through a process of ‘cape capture.’ The suggested former cape in Raleigh Bay represents the first interpreted geological evidence of dynamic abandonment suggested by the self-organization hypothesis. Cape capture may be a widespread process in coastal environments with large-scale rhythmic shoreline features; its preservation in the sedimentary record will vary according to geologic setting, physical processes, and sea-level history.

Applying petrophysical models to radar travel time and electrical resistivity tomograms: Resolution-dependent limitations

USGS Publications Warehouse

Day-Lewis, F. D.; Singha, K.; Binley, A.M.

2005-01-01

Geophysical imaging has traditionally provided qualitative information about geologic structure; however, there is increasing interest in using petrophysical models to convert tomograms to quantitative estimates of hydrogeologic, mechanical, or geochemical parameters of interest (e.g., permeability, porosity, water content, and salinity). Unfortunately, petrophysical estimation based on tomograms is complicated by limited and variable image resolution, which depends on (1) measurement physics (e.g., electrical conduction or electromagnetic wave propagation), (2) parameterization and regularization, (3) measurement error, and (4) spatial variability. We present a framework to predict how core-scale relations between geophysical properties and hydrologic parameters are altered by the inversion, which produces smoothly varying pixel-scale estimates. We refer to this loss of information as "correlation loss." Our approach upscales the core-scale relation to the pixel scale using the model resolution matrix from the inversion, random field averaging, and spatial statistics of the geophysical property. Synthetic examples evaluate the utility of radar travel time tomography (RTT) and electrical-resistivity tomography (ERT) for estimating water content. This work provides (1) a framework to assess tomograms for geologic parameter estimation and (2) insights into the different patterns of correlation loss for ERT and RTT. Whereas ERT generally performs better near boreholes, RTT performs better in the interwell region. Application of petrophysical models to the tomograms in our examples would yield misleading estimates of water content. Although the examples presented illustrate the problem of correlation loss in the context of near-surface geophysical imaging, our results have clear implications for quantitative analysis of tomograms for diverse geoscience applications. Copyright 2005 by the American Geophysical Union.

Interpretive geologic cross sections for the Death Valley regional flow system and surrounding areas, Nevada and California

USGS Publications Warehouse

Sweetkind, D.S.; Dickerson, R.P.; Blakely, R.J.; Denning, Paul

2001-01-01

This report presents a network of 28 geologic cross sections that portray subsurface geologic relations within the Death Valley regional ground-water system, a ground-water basin that encompasses a 3? x 3? area (approximately 70,000 km2) in southern Nevada and eastern California. The cross sections transect that part of the southern Great Basin that includes Death Valley, the Nevada Test Site, and the potential high-level nuclear waste underground repository at Yucca Mountain. The specific geometric relationships portrayed on the cross sections are discussed in the context of four general sub-regions that have stratigraphic similarities and general consistency of structural style: (1) the Nevada Test Site vicinity; (2) the Spring Mountains, Pahrump Valley and Amargosa Desert region; (3) the Death Valley region; and (4) the area east of the Nevada Test Site. The subsurface geologic interpretations portrayed on the cross sections are based on an integration of existing geologic maps, measured stratigraphic sections, published cross sections, well data, and geophysical data and interpretations. The estimated top of pre-Cenozoic rocks in the cross sections is based on inversion of gravity data, but the deeper parts of the sections are based on geologic conceptual models and are more speculative. The region transected by the cross sections includes part of the southern Basin and Range Province, the northwest-trending Walker Lane belt, the Death Valley region, and the northern Mojave Desert. The region is structurally complex, where a locally thick Tertiary volcanic and sedimentary section unconformably overlies previously deformed Proterozoic through Paleozoic rocks. All of these rocks have been deformed by complex Neogene ex-tensional normal and strike-slip faults. These cross sections form a three-dimensional network that portrays the interpreted stratigraphic and structural relations in the region; the sections form part of the geologic framework that will be incorporated in a complex numerical model of ground-water flow in the Death Valley region.

GeoFramework: A Modeling Framework for Solid Earth Geophysics

NASA Astrophysics Data System (ADS)

Gurnis, M.; Aivazis, M.; Tromp, J.; Tan, E.; Thoutireddy, P.; Liu, Q.; Choi, E.; Dicaprio, C.; Chen, M.; Simons, M.; Quenette, S.; Appelbe, B.; Aagaard, B.; Williams, C.; Lavier, L.; Moresi, L.; Law, H.

2003-12-01

As data sets in geophysics become larger and of greater relevance to other earth science disciplines, and as earth science becomes more interdisciplinary in general, modeling tools are being driven in new directions. There is now a greater need to link modeling codes to one another, link modeling codes to multiple datasets, and to make modeling software available to non modeling specialists. Coupled with rapid progress in computer hardware (including the computational speed afforded by massively parallel computers), progress in numerical algorithms, and the introduction of software frameworks, these lofty goals of merging software in geophysics are now possible. The GeoFramework project, a collaboration between computer scientists and geoscientists, is a response to these needs and opportunities. GeoFramework is based on and extends Pyre, a Python-based modeling framework, recently developed to link solid (Lagrangian) and fluid (Eulerian) models, as well as mesh generators, visualization packages, and databases, with one another for engineering applications. The utility and generality of Pyre as a general purpose framework in science is now being recognized. Besides its use in engineering and geophysics, it is also being used in particle physics and astronomy. Geology and geophysics impose their own unique requirements on software frameworks which are not generally available in existing frameworks and so there is a need for research in this area. One of the special requirements is the way Lagrangian and Eulerian codes will need to be linked in time and space within a plate tectonics context. GeoFramework has grown beyond its initial goal of linking a limited number of exiting codes together. The following codes are now being reengineered within the context of Pyre: Tecton, 3-D FE Visco-elastic code for lithospheric relaxation; CitComS, a code for spherical mantle convection; SpecFEM3D, a SEM code for global and regional seismic waves; eqsim, a FE code for dynamic earthquake rupture; SNAC, a developing 3-D coded based on the FLAC method for visco-elastoplastic deformation; SNARK, a 3-D FE-PIC method for viscoplastic deformation; and gPLATES an open source paleogeographic/plate tectonics modeling package. We will demonstrate how codes can be linked with themselves, such as a regional and global model of mantle convection and a visco-elastoplastic representation of the crust within viscous mantle flow. Finally, we will describe how http://GeoFramework.org has become a distribution site for a suite of modeling software in geophysics.

The geothermal energy potential in Denmark - updating the database and new structural and thermal models

NASA Astrophysics Data System (ADS)

Nielsen, Lars Henrik; Sparre Andersen, Morten; Balling, Niels; Boldreel, Lars Ole; Fuchs, Sven; Leth Hjuler, Morten; Kristensen, Lars; Mathiesen, Anders; Olivarius, Mette; Weibel, Rikke

2017-04-01

Knowledge of structural, hydraulic and thermal conditions of the subsurface is fundamental for the planning and use of hydrothermal energy. In the framework of a project under the Danish Research program 'Sustainable Energy and Environment' funded by the 'Danish Agency for Science, Technology and Innovation', fundamental geological and geophysical information of importance for the utilization of geothermal energy in Denmark was compiled, analyzed and re-interpreted. A 3D geological model was constructed and used as structural basis for the development of a national subsurface temperature model. In that frame, all available reflection seismic data were interpreted, quality controlled and integrated to improve the regional structural understanding. The analyses and interpretation of available relevant data (i.e. old and new seismic profiles, core and well-log data, literature data) and a new time-depth conversion allowed a consistent correlation of seismic surfaces for whole Denmark and across tectonic features. On this basis, new topologically consistent depth and thickness maps for 16 geological units from the top pre-Zechstein to the surface were drawn. A new 3D structural geological model was developed with special emphasis on potential geothermal reservoirs. The interpretation of petrophysical data (core data and well-logs) allows to evaluate the hydraulic and thermal properties of potential geothermal reservoirs and to develop a parameterized numerical 3D conductive subsurface temperature model. Reservoir properties and quality were estimated by integrating petrography and diagenesis studies with porosity-permeability data. Detailed interpretation of the reservoir quality of the geological formations was made by estimating net reservoir sandstone thickness based on well-log analysis, determination of mineralogy including sediment provenance analysis, and burial history data. New local surface heat-flow values (range: 64-84 mW/m2) were determined for the Danish Basin and predicted temperatures were calibrated and validated by borehole temperature observations. Finally, new temperature maps for major geological reservoir formations (Frederikshavn, Haldager Sand, Gassum and Bunter Sandstone/Skagerrak formations) and selected constant depth intervals (1 km, 2 km, etc.) were compiled. In the future, geothermal energy is likely to be a key component in Denmark's supply of energy and integrated into the district heating infrastructures. A new 3-year project (GEOTHERM) under the Innovation Fund Denmark will focus on addressing and removing remaining geological, technical and commercial obstacles. The presented 3D geothermal model will be an important component in more precise assessments of the geothermal resource, production capacity and thermal lifecycle.

Executive summary: Chapter A.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ruppert, Leslie F.; Ryder, Robert T.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

This publication supplements and updates older USGS regional studies of Appalachian basin coal and petroleum resources such as those by Arndt and others (1968) and the numerous contributors to USGS Miscellaneous Map Series I−917 (for example, Harris and others, 1978), respectively. USGS Professional Paper 1708 is intended primarily for geoscientists in academia, industry, and government who are interested in Appalachian basin geology and its coal and petroleum resources. Other users, however, may find the wide variety of topics, papers, and digital images of value for landuse and policy planning issues. Among the anticipated benefits of the report are improvements in (1) resource assessment estimates and methodology, (2) exploration strategies, (3) basin models, and (4) energy use policies.

Geologic map of the Rio Rico and Nogales 7.5’ quadrangles, Santa Cruz County, Arizona

USGS Publications Warehouse

Page, William R.; Menges, Christopher M.; Gray, Floyd; Berry, Margaret E.; Bultman, Mark W.; Cosca, Michael A.; VanSistine, D. Paco

2016-04-15

The objectives of our mapping were to define the geologic framework for the Nogales area and the upper Santa Cruz basin to support ongoing multidisciplinary projects. This new work will improve understanding of the Nogales Formation to more fully assess its groundwater resource potential. We significantly revised the Miocene Nogales Formation based on geologic mapping combined with new geochronologic, geophysical, and petrographic studies. 

The importance of geological data and derived information in seismic response assessment for urban sites. An example from the Island of Crete, Greece

NASA Astrophysics Data System (ADS)

Tsangaratos, Paraskevas; Loupasakis, Constantinos; Rozos, Dimitrios; Rondoyianni, Theodora; Vafidis, Antonios; Savvaidis, Alexandros; Soupios, Pantelis; Papadopoulos, Nikos; Sarris, Apostolos

2015-04-01

The magnitude, frequency content and duration of an earthquake ground motion depends mainly on the surrounding geological, tectonic and geomorphological conditions. Numerous reports have been contacted illustrating the necessity of providing accurate geological information in order to estimate the level of seismic hazard. In this context, geological information is the outcome of processing primary, raw field data and geotechnical investigation data that are non - organized and associated with the geological model of the study area. In most cases, the geological information is provided as an advance element, a key component of the "function" that solves any geo-environmental problem and is primarily reflected on analogue or digital maps. The main objective of the present study is to illustrate the importance of accurate geological information in the thirteen (13) selected sites of the Hellenic Accelerometric Network (HAN) in the area of Crete Island, in order to estimate the seismic action according to Eurocode (EC8). As an example the detailed geological-geotechnical map of the area around HAN site in Rethymno city, Crete is presented. The research area covers a 250m radius surrounding the RTHE HAN-station at a scale of 1: 2000 with detail description of the geological and geotechnical characteristics of the formations as well as the tectonic features (cracks, upthrust, thrust, etc) of the rock mass. The field survey showed that the RTHE station is founded over limestones and dolomites formations. The formations exhibit very good geomechanical behaviour; however they present extensive fragmentation and karstification. At this particular site the identification of a fault nearby the station proved to be significant information for the geophysical research as the location and orientation of the tectonic setting provided new perspective on the models of seismic wave prorogation. So, the geological data and the induced information along with the tectonic structure of the area, revealed variations that could alter the seismic wave prorogation models as well as the ground type/soil category of the foundation formations. In conclusion, the produced geological-geotechnical maps are the main mean of communication and flow of geological information between different scientific disciplines providing the bases for defining the ground type at each HAN site and calibrating the corresponding code prescribed spectra. This study is part of the on-going project that has been co-financed by the European Union (European Social Fund - ESF) and Greek national funds through the Operational Program "Education and Lifelong Learning" of the National Strategic Reference Framework (NSRF) - Research Funding Program: THALES. Investing in knowledge society through the European Social Fund.

The National Danish Water Resources Model - using an integrated groundwater - surface water model for decision support and WFD implementation in a changing climate

NASA Astrophysics Data System (ADS)

Lajer Hojberg, Anker; Hinsby, Klaus; Jørgen Henriksen, Hans; Troldborg, Lars

2014-05-01

Integrated and sustainable water resources management and development of river basin management plans according to the Water Framework Directive is getting increasingly complex especially when taking projected climate change into account. Furthermore, uncertainty in future developments and incomplete knowledge of the physical system introduces a high degree of uncertainty in the decision making process. Knowledge based decision making is therefore vital for formulation of robust management plans and to allow assessment of the inherent uncertainties. The Department of Hydrology at the Geological Survey of Denmark and Greenland started in 1996 to develop a mechanistically, transient and spatially distributed groundwater-surface water model - the DK-model - for the assessment of groundwater quantitative status accounting for interactions with surface water and anthropogenic changes, such as extraction strategies and land use, as well as climate change. The model has been subject to continuous update building on hydrogeological knowledge established by the regional water authorities and other national research institutes. With the on-going improvement of the DK-model it is now increasingly applied both by research projects and for decision support e.g. in implementation of the Water Framework Directive or to support other decisions related to protection of water resources (quantitative and chemical status), ecosystems and the built environment. At present, the DK-model constitutes the backbone of a strategic modelling project funded by the Danish Environmental Protection Agency, with the aim of developing a modelling complex that will provide the foundation of the implementation of the Water Framework Directive. Since 2003 the DK-model has been used in more than 25 scientific papers and even more public reports. In the poster and the related review paper we describe the most important applications in both science and policy, where the DK-model has been used either directly or as an important starting point for assessing the impact of climate change on the quantity and quality of groundwater and surface water e.g. in relation to changes in water tables, runoff, nutrient loadings, flooding risks (coastal and hinterland), irrigation demands, sea level rise and seawater intrusion or to assess where geology or climate change create the largest uncertainty for evaluation of the development of water resources quantity and quality.

Integrated modeling of natural and human systems - problems and initiatives

NASA Astrophysics Data System (ADS)

Kessler, H.; Giles, J.; Gunnink, J.; Hughes, A.; Moore, R. V.; Peach, D.

2009-12-01

Governments and their executive agencies across the world are facing increasing pressure to make decisions about the management of resources in light of population growth and environmental change. In the UK and the Netherlands, for example, groundwater is becoming a scarce resource for large parts of its most densely populated areas. At the same time river and groundwater flooding resulting from high rainfall events are increasing in scale and frequency and sea level rise is threatening the defences of coastal cities. There is also a need for affordable housing, improved transport infrastructure and waste disposal as well as sources of renewable energy and sustainable food production. These challenges can only be resolved if solutions are based on sound scientific evidence. Although we have knowledge and understanding of many individual processes in the natural sciences it is clear that a single science discipline is unable to answer the questions and their inter-relationships. Modern science increasingly employs computer models to simulate the natural, economic and human system. Management and planning requires scenario modelling, forecasts and “predictions”. Although the outputs are often impressive in terms of apparent accuracy and visualisation, they are inherently not suited to simulate the response to feedbacks from other models of the earth system, such as the impact of human actions. Geological Survey Organisations (GSO) are increasingly employing advances in Information Technology to visualise and improve their understanding of geological systems. Instead of 2 dimensional paper maps and reports many GSOs now produce 3 dimensional geological framework models and groundwater flow models as their standard output. Additionally the British Geological Survey and the Geological Survey of the Netherlands have developed standard routines to link geological data to groundwater models, but these models are only aimed at solving one specific part of the earth's system, e.g. the flow of groundwater to an abstraction borehole or the availability of water for irrigation. Particular problems arise when model data from two or more disciplines are incompatible in terms of data formats, scientific concepts or language. Other barriers include the cultural segregation within and between science disciplines as well as impediments to data exchange due to ownership and copyright restrictions. OpenMI and GeoSciML are initiatives that are trying to overcome these barriers by building international communities that share vocabularies and data formats. This paper will give examples of the successful merging of geological and hydrological models from the UK and the Netherlands and will introduce the vision of an open Environmental Modelling Platform which aims to link data, knowledge and concepts seamlessly to numerical process models. Last but not least there is an urgent need to create a Subsurface Management System akin to a Geographic Information System in which all results of subsurface modelling can be visualised and analysed in an integrated manner.

Use of decision support systems as a drought management tool

USGS Publications Warehouse

Frevert, D.; Lins, H.; ,

2005-01-01

Droughts present a unique challenge to water managers throughout the world and the current drought in the western United States is taxing facilities to the limit. Coping with this severe drought requires state of the art decision support systems including efficient and accurate hydrologic process models, detailed hydrologic data bases and effective river systems management modeling frameworks. This paper will outline a system of models developed by the Bureau of Reclamation, the US Geological Survey, the University of Colorado and a number of other governmental and university partners. The application of the technology to drought management in several key western river basins will be discussed.

Abnormal pressures as hydrodynamic phenomena

USGS Publications Warehouse

Neuzil, C.E.

1995-01-01

So-called abnormal pressures, subsurface fluid pressures significantly higher or lower than hydrostatic, have excited speculation about their origin since subsurface exploration first encountered them. Two distinct conceptual models for abnormal pressures have gained currency among earth scientists. The static model sees abnormal pressures generally as relict features preserved by a virtual absence of fluid flow over geologic time. The hydrodynamic model instead envisions abnormal pressures as phenomena in which flow usually plays an important role. This paper develops the theoretical framework for abnormal pressures as hydrodynamic phenomena, shows that it explains the manifold occurrences of abnormal pressures, and examines the implications of this approach. -from Author

The evolution, approval and implementation of the U.S. Geological Survey Science Data Lifecycle Model

USGS Publications Warehouse

Faundeen, John L.; Hutchison, Vivian

2017-01-01

This paper details how the United States Geological Survey (USGS) Community for Data Integration (CDI) Data Management Working Group developed a Science Data Lifecycle Model, and the role the Model plays in shaping agency-wide policies. Starting with an extensive literature review of existing data Lifecycle models, representatives from various backgrounds in USGS attended a two-day meeting where the basic elements for the Science Data Lifecycle Model were determined. Refinements and reviews spanned two years, leading to finalization of the model and documentation in a formal agency publication . The Model serves as a critical framework for data management policy, instructional resources, and tools. The Model helps the USGS address both the Office of Science and Technology Policy (OSTP) for increased public access to federally funded research, and the Office of Management and Budget (OMB) 2013 Open Data directives, as the foundation for a series of agency policies related to data management planning, metadata development, data release procedures, and the long-term preservation of data. Additionally, the agency website devoted to data management instruction and best practices (www2.usgs.gov/datamanagement) is designed around the Model’s structure and concepts. This paper also illustrates how the Model is being used to develop tools for supporting USGS research and data management processes.

Hydromechanical coupling in geologic processes

USGS Publications Warehouse

Neuzil, C.E.

2003-01-01

Earth's porous crust and the fluids within it are intimately linked through their mechanical effects on each other. This paper presents an overview of such "hydromechanical" coupling and examines current understanding of its role in geologic processes. An outline of the theory of hydromechanics and rheological models for geologic deformation is included to place various analytical approaches in proper context and to provide an introduction to this broad topic for nonspecialists. Effects of hydromechanical coupling are ubiquitous in geology, and can be local and short-lived or regional and very long-lived. Phenomena such as deposition and erosion, tectonism, seismicity, earth tides, and barometric loading produce strains that tend to alter fluid pressure. Resulting pressure perturbations can be dramatic, and many so-called "anomalous" pressures appear to have been created in this manner. The effects of fluid pressure on crustal mechanics are also profound. Geologic media deform and fail largely in response to effective stress, or total stress minus fluid pressure. As a result, fluid pressures control compaction, decompaction, and other types of deformation, as well as jointing, shear failure, and shear slippage, including events that generate earthquakes. By controlling deformation and failure, fluid pressures also regulate states of stress in the upper crust. Advances in the last 80 years, including theories of consolidation, transient groundwater flow, and poroelasticity, have been synthesized into a reasonably complete conceptual framework for understanding and describing hydromechanical coupling. Full coupling in two or three dimensions is described using force balance equations for deformation coupled with a mass conservation equation for fluid flow. Fully coupled analyses allow hypothesis testing and conceptual model development. However, rigorous application of full coupling is often difficult because (1) the rheological behavior of geologic media is complex and poorly understood and (2) the architecture, mechanical properties and boundary conditions, and deformation history of most geologic systems are not well known. Much of what is known about hydromechanical processes in geologic systems is derived from simpler analyses that ignore certain aspects of solid-fluid coupling. The simplifications introduce error, but more complete analyses usually are not warranted. Hydromechanical analyses should thus be interpreted judiciously, with an appreciation for their limitations. Innovative approaches to hydromechanical modeling and obtaining critical data may circumvent some current limitations and provide answers to remaining questions about crustal processes and fluid behavior in the crust.

Geologic interpretation and multibeam bathymetry of the sea floor in the vicinity of the Race, eastern Long Island Sound

USGS Publications Warehouse

Poppe, L.J.; DiGiacomo-Cohen, M. L.; Doran, E.F.; Smith, S.M.; Stewart, H.F.; Forfinski, N.A.

2007-01-01

Digital terrain models (DTMs) produced from multibeam bathymetric data provide valuable base maps for marine geological interpretations (Todd and others, 1999; Mosher and Thomson, 2002; ten Brink and others, 2004; Poppe and others, 2006a, b, c, d). These maps help define the geological variability of the sea floor (one of the primary controls of benthic habitat diversity), improve our understanding of the processes that control the distribution and transport of bottom sediments and the distribution of benthic habitats and associated infaunal community structures, and provide a detailed framework for future research, monitoring, and management activities. The bathymetric survey interpreted herein (National Oceanic and Atmospheric Administration (NOAA) survey H11250) covers roughly 94 km² of sea floor in an area where a depression along the Orient Point-Fishers Island segment of the Harbor Hill-Roanoke Point-Charlestown Moraine forms the Race, the eastern opening to Long Island Sound. The Race also divides easternmost Long Island Sound from northwestern Block Island Sound (fig. 1). This bathymetry has been examined in relation to seismic reflection data collected concurrently, as well as archived seismic profiles acquired as part of a long-standing geologic mapping partnership between the State of Connecticut and the U.S. Geological Survey (USGS). The objective of this work was to use these acoustic data sets to interpret geomorphological attributes of the sea floor, and to use these interpretations to better understand the Quaternary geologic history and modern sedimentary processes.

From printed geological maps to web-based service oriented data products - strategies, foundations and problems.

NASA Astrophysics Data System (ADS)

Ebner, M.; Schiegl, M.; Stöckl, W.; Heger, H.

2012-04-01

The Geological Survey of Austria is legally obligated by the INSPIRE directive to provide data that fall under this directive (geology, mineral resources and natural risk zones) to the European commission in a semantically harmonized and technically interoperable way. Until recently the focus was entirely on the publication of high quality printed cartographic products. These have a complex (carto-)graphic data-model, which allows visualizing several thematic aspects, such as lithology, stratigraphy, tectonics, geologic age, mineral resources, mass movements, geomorphology etc. in a single planar map/product. Nonetheless these graphic data-models do not allow retrieving individual thematic aspects since these were coded in a complex portrayal scheme. Automatic information retrieval is thus impossible; and domain knowledge is necessary to interpret these "encrypted datasets". With INSPIRE becoming effective and a variety of conceptual models (e.g. GeoSciML), built around a semantic framework (i.e. controlled vocabularies), being available it is necessary to develop a strategy and workflow for semantic harmonization of such datasets. In this contribution we demonstrate the development of a multistage workflow which will allow us to transform our printed maps to semantically enabled datasets and services and discuss some prerequisites, foundations and problems. In a first step in our workflow we analyzed our maps and developed controlled vocabularies that describe the thematic content of our data. We then developed a physical data-model which we use to attribute our spatial data with thematic information from our controlled vocabularies to form core thematic data sets. This physical data model is geared towards use on an organizational level but builds upon existing standards (INSPIRE, GeoSciML) to allow transformation to international standards. In a final step we will develop a standardized mapping scheme to publish INSPIRE conformant services from our core datasets. This two-step transformation is necessary since a direct mapping to international standards is not possible for traditional map-based data. Controlled vocabularies provide the foundation of a semantic harmonization. For the encoding of the vocabularies we build upon the W3C standard SKOS (=Simple Knowledge Organisation System), a thesaurus specification for the semantic web, which is itself based on the Resource Description Framework (RDF) and RDF Schema and added some DublinCore and VoID for the metadata of our vocabularies and resources. For the development of these thesauri we use the commercial software PoolParty, which is a tool specially build to develop, manage and publish multilingual thesauri. The corporate thesauri of the Austrian Geological Survey are exposed via a web-service that is conformant with the linked data principles. This web-service gives access to a (1) RDF/HTML representation of the resources via a simple, robust and thus persistent http URIs (2) a download of the complete vocabularies in RDF-format (3) a full-fledged SPARQL-Endpoint to query the thesaurus. With the development of physical data-models (based on preexisting conceptual models) one must dismiss the classical schemes of map-based portrayal of data. E.g. for individual Geological units on traditional geological maps usually a single age range is given (e.g. formation age). But one might want to attribute several geologic ages (formation age, metamorphic age, cooling ages etc.) to individual units. Such issues have to be taken into account when developing robust physical data-models. Based on our experience we are convinced that individual institutions need to develop their own controlled vocabularies and individual data-models that fit the specific needs on an organizational level. If externally developed vocabularies and data-models are introduced to established workflows newly generated and existing data may be diverging and it will be hard to achieve or maintain a common standard. We thus suggest that it is necessary for institutions to keep (or develop) to their organizational standards and vocabularies and map them to generally agreed international standards such as INSPIRE or GeoSciML in a fashion suggested by the linked data principles.

A new process sensitivity index to identify important system processes under process model and parametric uncertainty

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dai, Heng; Ye, Ming; Walker, Anthony P.

Hydrological models are always composed of multiple components that represent processes key to intended model applications. When a process can be simulated by multiple conceptual-mathematical models (process models), model uncertainty in representing the process arises. While global sensitivity analysis methods have been widely used for identifying important processes in hydrologic modeling, the existing methods consider only parametric uncertainty but ignore the model uncertainty for process representation. To address this problem, this study develops a new method to probe multimodel process sensitivity by integrating the model averaging methods into the framework of variance-based global sensitivity analysis, given that the model averagingmore » methods quantify both parametric and model uncertainty. A new process sensitivity index is derived as a metric of relative process importance, and the index includes variance in model outputs caused by uncertainty in both process models and model parameters. For demonstration, the new index is used to evaluate the processes of recharge and geology in a synthetic study of groundwater reactive transport modeling. The recharge process is simulated by two models that converting precipitation to recharge, and the geology process is also simulated by two models of different parameterizations of hydraulic conductivity; each process model has its own random parameters. The new process sensitivity index is mathematically general, and can be applied to a wide range of problems in hydrology and beyond.« less

Crustal-scale geological and thermal models of the Beaufort-Mackenzie Basin, Arctic Canada

NASA Astrophysics Data System (ADS)

Sippel, Judith; Scheck-Wenderoth, Magdalena; Kröger, Karsten; Lewerenz, Björn

2010-05-01

The Beaufort-Mackenzie Basin is a petroliferous province in northwest Arctic Canada and one of the best-known segments of the Arctic Ocean margin due to decades of exploration. Our study is part of the programme MOM (Methane On the Move), which aims to quantify the methane contribution from natural petroleum systems to the atmosphere over geological times. Models reflecting the potential of a sedimentary basin to release methane require well-assessed boundary conditions such as the crustal structure and large-scale temperature variation. We focus on the crustal-scale thermal field of the Beaufort-Mackenzie Basin. This Basin has formed on a post-rift, continental margin which, during the Late Cretaceous and Tertiary, developed into the foreland of the North American Cordilleran foldbelt providing space for the accumulation of up to 16 km of foreland deposits. We present a 3D geological model which integrates the present topography, depth maps of Upper Cretaceous and Tertiary horizons (Kroeger et al., 2008, 2009), tops of formations derived from interpreted 2D reflection seismic lines and 284 boreholes (released by the National Energy Board of Canada), and the sequence stratigraphic framework established by previous studies (e.g. Dixon et al., 1996). To determine the position and geometry of the crust-mantle boundary, an isostatic calculation (Airýs model) is applied to the geological model. We present different crustal-scale models combining isostatic modelling, published deep reflection and refraction seismic lines (e.g. Stephenson et al., 1994; O'Leary et al., 1995), and calculations of the 3D conductive thermal field. References: Dixon, J., 1996. Geological Atlas of the Beaufort-Mackenzie Area, Geological Survey of Canada Miscellaneous Report, 59, Ottawa, 173 pp. Kroeger, K.F., Ondrak, R., di Primio, R. and Horsfield, B., 2008. A three-dimensional insight into the Mackenzie Basin (Canada): Implications for the thermal history and hydrocarbon generation potential of Tertiary deltaic sequences, AAPG Bulletin, 92(2): 225-247. Kroeger, K.F., di Primio, R. and Horsfield, B., (2009). Hydrocarbon flow modeling in complex structures (Mackenzie Basin, Canada), AAPG Bulletin, 93(9): 1-25. O'Leary, D.M., Ellis, R.M., Stephenson, R.A., Lane, L.S. and Zelt, C.A., 1995. Crustal structure of the northern Yukon and Mackenzie Delta, northwestern Canada, Journal of Geophysical Research 100(B7): 9905-9920. Stephenson, R.A., Coflin, K.C., Lane, L.S. and Dietrich, J.R., 1994. Crustal structure and tectonics of the southeastern Beaufort Sea continental margin, Tectonics, 13(2): 389-400.

A dynamic water-quality modeling framework for the Neuse River estuary, North Carolina

USGS Publications Warehouse

Bales, Jerad D.; Robbins, Jeanne C.

1999-01-01

As a result of fish kills in the Neuse River estuary in 1995, nutrient reduction strategies were developed for point and nonpoint sources in the basin. However, because of the interannual variability in the natural system and the resulting complex hydrologic-nutrient inter- actions, it is difficult to detect through a short-term observational program the effects of management activities on Neuse River estuary water quality and aquatic health. A properly constructed water-quality model can be used to evaluate some of the potential effects of manage- ment actions on estuarine water quality. Such a model can be used to predict estuarine response to present and proposed nutrient strategies under the same set of meteorological and hydrologic conditions, thus removing the vagaries of weather and streamflow from the analysis. A two-dimensional, laterally averaged hydrodynamic and water-quality modeling framework was developed for the Neuse River estuary by using previously collected data. Development of the modeling framework consisted of (1) computational grid development, (2) assembly of data for model boundary conditions and model testing, (3) selection of initial values of model parameters, and (4) limited model testing. The model domain extends from Streets Ferry to Oriental, N.C., includes seven lateral embayments that have continual exchange with the main- stem of the estuary, three point-source discharges, and three tributary streams. Thirty-five computational segments represent the mainstem of the estuary, and the entire framework contains a total of 60 computa- tional segments. Each computational cell is 0.5 meter thick; segment lengths range from 500 meters to 7,125 meters. Data that were used to develop the modeling framework were collected during March through October 1991 and represent the most comprehensive data set available prior to 1997. Most of the data were collected by the North Carolina Division of Water Quality, the University of North Carolina Institute of Marine Sciences, and the U.S. Geological Survey. Limitations in the modeling framework were clearly identified. These limitations formed the basis for a set of suggestions to refine the Neuse River estuary water-quality model.

Sudbury project (University of Muenster-Ontario Geological Survey): Isotope systematics support the impact origin

NASA Technical Reports Server (NTRS)

Deutsch, A.; Buhl, D.; Brockmeyer, P.; Lakomy, R.; Flucks, M.

1992-01-01

Within the framework of the Sudbury project a considerable number of Sr-Nd isotope analyses were carried out on petrographically well-defined samples of different breccia units. Together with isotope data from the literature these data are reviewed under the aspect of a self-consistent impact model. The crucial point of this model is that the Sudbury Igneous Complex (SIC) is interpreted as a differentiated impact melt sheet without any need for an endogenic 'magmatic' component such as 'impact-triggered' magmatism or 'partial' impact melting of the crust and mixing with a mantle-derived magma.

Geologic framework for the national assessment of carbon dioxide storage resources: U.S. Gulf Coast: Chapter H in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Roberts-Ashby, Tina L.; Brennan, Sean T.; Buursink, Marc L.; Covault, Jacob A.; Craddock, William H.; Drake II, Ronald M.; Merrill, Matthew D.; Slucher, Ernie R.; Warwick, Peter D.; Blondes, Madalyn S.; Gosai, Mayur A.; Freeman, P.A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2014-01-01

This report presents 27 storage assessment units (SAUs) within the United States (U.S.) Gulf Coast. The U.S. Gulf Coast contains a regionally extensive, thick succession of clastics, carbonates, salts, and other evaporites that were deposited in a highly cyclic depositional environment that was subjected to a fluctuating siliciclastic sediment supply and transgressive and regressive sea levels. At least nine major depositional packages contain porous strata that are potentially suitable for geologic carbon dioxide (CO2) sequestration within the region. For each SAU identified within these packages, the areal distribution of porous rock that is suitable for geologic CO2 sequestration is discussed, along with a description of the geologic characteristics that influence the potential CO2 storage volume and reservoir performance. These characteristics include reservoir depth, gross thickness, net-porous thickness, porosity, permeability, and groundwater salinity. Additionally, a characterization of the overlying regional seal for each SAU is presented. On a case-by-case basis, strategies for estimating the pore volume existing within structurally and (or) stratigraphically closed traps are also presented. Geologic information presented in this report has been employed to calculate potential storage capacities for CO2 sequestration in the SAUs that are assessed herein, although complete assessment results are not contained in this report.

Shallow geology, sea-floor texture, and physiographic zones of Buzzards Bay, Massachusetts

USGS Publications Warehouse

Foster, David S.; Baldwin, Wayne E.; Barnhardt, Walter A.; Schwab, William C.; Ackerman, Seth D.; Andrews, Brian D.; Pendleton, Elizabeth A.

2015-01-07

Geologic, sediment texture, and physiographic zone maps characterize the sea floor of Buzzards Bay, Massachusetts. These maps were derived from interpretations of seismic-reflection profiles, high-resolution bathymetry, acoustic-backscatter intensity, bottom photographs, and surficial sediment samples. The interpretation of the seismic stratigraphy and mapping of glacial and Holocene marine units provided a foundation on which the surficial maps were created. This mapping is a result of a collaborative effort between the U.S. Geological Survey and the Massachusetts Office of Coastal Zone Management to characterize the surface and subsurface geologic framework offshore of Massachusetts.

Catastrophism in geology

NASA Astrophysics Data System (ADS)

Hallam, A.

An historical survey is presented of ideas relating to the concept of 'catastrophism' in geological studies during the last two centuries. It is noted in particular that the opposing concept of 'uniformitarianism', in which there is assumed to have been an overall constancy of geological processes through time so that there is no need to invoke catastrophic change, is now considered rather extreme. During the nineteen sixties and seventies, a neocatastrophist viewpoint has increasingly emerged in various branches of geology. Mass extinctions and their possible causes - bolide impact, climate, volcanism and sea-level change for example - are each considered in the context of this developing framework.

Building continental-scale 3D subsurface layers in the Digital Crust project: constrained interpolation and uncertainty estimation.

NASA Astrophysics Data System (ADS)

Yulaeva, E.; Fan, Y.; Moosdorf, N.; Richard, S. M.; Bristol, S.; Peters, S. E.; Zaslavsky, I.; Ingebritsen, S.

2015-12-01

The Digital Crust EarthCube building block creates a framework for integrating disparate 3D/4D information from multiple sources into a comprehensive model of the structure and composition of the Earth's upper crust, and to demonstrate the utility of this model in several research scenarios. One of such scenarios is estimation of various crustal properties related to fluid dynamics (e.g. permeability and porosity) at each node of any arbitrary unstructured 3D grid to support continental-scale numerical models of fluid flow and transport. Starting from Macrostrat, an existing 4D database of 33,903 chronostratigraphic units, and employing GeoDeepDive, a software system for extracting structured information from unstructured documents, we construct 3D gridded fields of sediment/rock porosity, permeability and geochemistry for large sedimentary basins of North America, which will be used to improve our understanding of large-scale fluid flow, chemical weathering rates, and geochemical fluxes into the ocean. In this talk, we discuss the methods, data gaps (particularly in geologically complex terrain), and various physical and geological constraints on interpolation and uncertainty estimation.

Analysis of Geologic CO2 Sequestration at Farnham Dome, Utah, USA

NASA Astrophysics Data System (ADS)

Lee, S.; Han, W.; Morgan, C.; Lu, C.; Esser, R.; Thorne, D.; McPherson, B.

2008-12-01

The Farnham Dome in east-central Utah is an elongated, Laramide-age anticline along the northern plunge of the San Rafael uplift and the western edge of the Uinta Basin. We are helping design a proposed field demonstration of commercial-scale geologic CO2 sequestration, including injection of 2.9 million tons of CO2 over four years time. The Farnham Dome pilot site stratigraphy includes a stacked system of saline formations alternating with low-permeability units. Facilitating the potential sequestration demonstration is a natural CO2 reservoir at depth, the Jurassic-age Navajo formation, which contains an estimated 50 million tons of natural CO2. The sequestration test design includes two deep formations suitable for supercritical CO2 injection, the Jurassic-age Wingate sandstone and the Permian-age White Rim sandstone. We developed a site-specific geologic model based on available geophysical well logs and formation tops data for use with numerical simulation. The current geologic model is limited to an area of approximately 6.5x4.5 km2 and 2.5 km thick, which contains 12 stacked formations starting with the White Rim formation at the bottom (>5000 feet bgl) and extending to the Jurassic Curtis formation at the top of the model grid. With the detail of the geologic model, we are able to estimate the Farnham Dome CO2 capacity at approximately 36.5 million tones within a 5 mile radius of a single injection well. Numerical simulation of multiphase, non- isothermal CO2 injection and flow suggest that the injected CO2 plume will not intersect nearby fault zones mapped in previous geologic studies. Our simulations also examine and compare competing roles of different trapping mechanisms, including hydrostratigraphic, residual gas, solubility, and mineralization trapping. Previous studies of soil gas flux at the surface of the fault zones yield no significant evidence of CO2 leakage from the natural reservoir at Farnham Dome, and thus we use these simulations to evaluate what factors make this natural reservoir so effective for CO2 storage. Our characterization and simulation efforts are producing a CO2 sequestration framework that incorporates production and capacity estimation, area-of-review, injectivity, and trapping mechanisms. Likewise, mitigation and monitoring strategies have been formulated from the site characterization and modeling results.

Geology for Global Development: Mobilising and equipping young geologists to engage in disaster risk reduction

NASA Astrophysics Data System (ADS)

Gill, Joel

2016-04-01

Geology for Global Development (GfGD) is a not-for-profit organisation working to mobilise and equip geologists to engage in all aspects of sustainable development, including disaster risk reduction (DRR). Geologists have a crucial role to play in DRR, and the recently agreed Sendai Framework for DRR 2015-2030. This framework aims to significantly reduce loss of lives and livelihoods due to disasters. The geology community have an understanding of the Earth, its physical structure, and the processes by which it is constantly being shaped which are of particular relevance to Priorities for Action 1 and 4 noted within the Sendai Framework. Effective engagement by geologists, however, requires many skills beyond the standard geology curriculum. Cultural understanding, cross-disciplinary communication, diplomacy, community mobilization and participation, knowledge exchange, and an understanding of social science research tools are commonly necessary for effective research and engagement in the science-policy-practice interface. Topical and disciplinary knowledge, such as understanding social vulnerability, international policy frameworks and development theory are also rarely included in the education and professional training of a young geologist. Through the work of GfGD, we are training young geologists with these skills and the supporting knowledge required to make an effective contribution to reducing disaster risk, support civil society, empower communities and help to strengthen resilience. University chapters have been established in 14 major UK and Irish universities, coordinating extra-curricular seminars, workshops and discussion activities. Our work is currently focused on supporting young geologists, but we are increasingly a respected voice at international geoscience forums that gather a wide range of students and professionals. Wider (national and international) activities include conferences, placements and facilitating youth engagement in education, outreach and development projects.

Encoding of Geological knowledge in the GeoPiemonte Map Data Base

NASA Astrophysics Data System (ADS)

Piana, Fabrizio; Lombardo, Vincenzo; Mimmo, Dario; Barale, Luca; Irace, Andrea; Mulazzano, Elia

2017-04-01

In modern digital geological maps and geo-database, namely those devoted to interactive WebGIS services, there is the need to make explicit the geological assumptions in the process of the design and compilation of the Map Geodatabase. The Geodatabase of the Piemonte Geological Map, which consists of several thousands of Geologic Units and Geologic Structures, was designed in a way suitable for linking the knowledge of the geological domain at hand to more general levels of knowledge, represented in existing Earth Sciences ontologies and in a domain ontology (OntoGeonous), specifically designed for the project, though with a wide applicability in mind. The Geologic Units and Geologic Structures of the GeoPiemonte Map have been spatially correlated through the whole region, referring to a non-formal hierarchical scheme, which gives the parental relations between several orders of Geologic Units, putting them in relations with some main Geologic Events. The scheme reports the subdivisions we did on the Alps-Apennines orogenic belt (which constitutes the Piemonte geological framework) on which the architecture of the GeoDB relied. This contribution describes how the two different knowledge levels (specific domain vs. general knowledge) are assimilated within the GeoPiemonte informative system, providing relations between the contents of the geodatabase and the encoded concepts of the reference ontologies. Initiatives such as GeoScience Markup Language (GeoSciML 4.01, 2016 (1) and INSPIRE "Data Specification on Geology" (an operative simplification of GeoSciML, last version is 3.0, 2013) (2), as well as the recent terminological shepherding of the Geoscience Terminology Working Group (GTWG), provided us the authoritative standard geological source for knowledge encoding. Consistency and interoperability of geological data were thus sought, by classifying geologic features in an ontology-driven Data Model, while objects were described using GeoSciML controlled vocabularies and concepts derived from NASA SWEET ontology (3) (4) (5). At the state of the art the GeoPiemonte Map informative system is thus suitable for integration in trans-national Data Infrastructures and/or WebMap Services that require interoperability and harmonised semantic approaches. References (1)http://www.geosciml.org/geosciml/4.0/documentation/html/ - GeoSciML Data Model - (2)http://inspire.ec.europa.eu/documents/Data_Specifications/INSPIRE_DataSpecification_GE_v3.0.pdf - INSPIRE DS Technical Guidelines (3)http://resource.geosciml.org/vocabulary/cgi/201211/simplelithology.html (4)http://resource.geosciml.org/vocabulary/cgi/ - CGI GTWG controlled vocabularies repository (5) SWEET (Semantic Web for Earth and Environmental Terminology), http://www.sweet.jpl.nasa.govAppel Piana et al., 2017a. Geology of Piemonte Region (NW Italy, Alps-Apennines junction zone). Journal of Maps, in press. Piana et al., 2017b. The Geodatabase of the Piemonte Geological Map: conceptual design for knowledge encoding. ROL Soc. Geol. It., in press.

CONSIDERATIONS FOR A REGULATORY FRAMEWORK FOR LARGE-SCALE GEOLOGIC SEQUESTRATION OF CARBON DIOXIDE: A NORTH AMERICAN PERSPECTIVE

EPA Science Inventory

Large scale geologic sequestration (GS) of carbon dioxide poses a novel set of challenges for regulators. This paper focuses on the unique needs of large scale GS projects in light of the existing regulatory regimes in the United States and Canada and identifies several differen...

National Oceanic and Atmospheric Administration hydrographic survey data used in a U.S. Geological Survey regional geologic framework study along the Delmarva Peninsula

USGS Publications Warehouse

Pendleton, Elizabeth A.; Brothers, Laura L.; Thieler, E. Robert; Danforth, William W.; Parker, Castle E.

2014-01-01

The U.S. Geological Survey obtained raw Reson multibeam data files from Science Applications International Corporation and the National Oceanic and Atmospheric Administration for 20 hydrographic surveys and extracted backscatter data using the Fledermaus Geocoder Toolbox from Quality Positioning Service. The backscatter mosaics produced by the U.S. Geological Survey for the inner continental shelf of the Delmarva Peninsula using National Oceanic and Atmospheric Administration data increased regional geophysical surveying efficiency, collaboration among government agencies, and the area over which geologic data can be interpreted by the U.S. Geological Survey. This report describes the methods by which the backscatter data were extracted and processed and includes backscatter mosaics and interpolated bathymetric surfaces.

Comment on "Geochemistry of the Early Miocene volcanic succession of Northland, New Zealand, and implications for the evolution of subduction in the Southwest Pacific" by M.A. Booden, I.E.M. Smith, P.M. Black and J.L. Mauk

NASA Astrophysics Data System (ADS)

Schellart, W. P.

2012-01-01

In a recent paper Booden et al. (2011) present new geochemical and petrological data of Early Miocene volcanics from the Northland region (Northland volcanic belt) in New Zealand, and interpret these data to support a particular regional tectonic model. This tectonic model involves Early Miocene westward subduction of Cretaceous Pacific oceanic lithosphere below the Northland volcanic belt and the authors interpret the volcanic belt as a continental magmatic arc. Although the new data are not in disagreement with such a tectonic model, they provide more support for an alternative interpretation that involves a northeast-dipping subduction zone. Furthermore, geometric and plate kinematic data show that the west-dipping subduction model is unviable, geological and geophysical data contradict the model, while geodynamic arguments indicate that the model is implausible. Here it will be shown that a subduction model, involving a northeast-dipping southwestward retreating slab (made of the Late Cretaceous-Paleocene South Loyalty backarc basin lithosphere) that subsequently detaches, is in agreement with the local geology, geophysics and geochemistry, is geometrically, kinematically and geodynamically viable, and fits within the regional Southwest Pacific tectonic framework.

Bedrock geologic map of the Worcester South quadrangle, Worcester County, Massachusetts

USGS Publications Warehouse

Walsh, Gregory J.; Merschat, Arthur J.

2015-09-29

The bedrock geology was mapped to study the tectonic history of the area and to provide a framework for ongoing hydrogeologic characterization of the fractured bedrock of Massachusetts. This report presents mapping by Gregory J. Walsh and Arthur J. Merschat from 2008 to 2010. The report consists of a map and GIS database, both of which are available for download at http://dx.doi.org/ 10.3133/sim3345. The database includes contacts of bedrock geologic units, faults, outcrop locations, structural information, and photographs.

Geologic map of the west-central Buffalo National River region, northern Arkansas

USGS Publications Warehouse

Hudson, Mark R.; Turner, Kenzie J.

2014-01-01

This report provides a geologic map database of the map area that improves understanding of the regional geologic framework and its influence on the regional groundwater flow system. Furthermore, additional edits were made to the Ponca and Jasper quadrangles in the following ways: new control points on important contacts were obtained using modern GPS; recent higher resolution elevation data allowed further control on placement of contacts; some new contacts were added, in particular the contact separating the upper and lower Everton Formation.

Audiomagnetotelluric data, Taos Plateau Volcanic Field, New Mexico

USGS Publications Warehouse

Ailes, Chad E.; Rodriguez, Brian D.

2011-01-01

The U.S. Geological Survey is conducting a series of multidisciplinary studies of the San Luis Basin as part of the Geologic framework of the Rio Grande Basins project. Detailed geologic mapping, high-resolution airborne magnetic surveys, gravity surveys, audiomagnetotelluric surveys, and hydrologic and lithologic data are being used to better understand the aquifers. This report describes a regional east-west audiomagnetotelluric sounding profile acquired in late July 2009 across the Taos Plateau Volcanic Field. No interpretation of the data is included.

Setting up a model intercomparison project for the last deglaciation

NASA Astrophysics Data System (ADS)

Ivanovic, R. F.; Gregoire, L. J.; Valdes, P. J.; Roche, D. M.; Kageyama, M.

2014-12-01

The last deglaciation (~ 21-9 ka) presents a series of opportunities to study the underlying mechanisms of abrupt climate changes and long-term trends in the Earth System. Most of the forcings are relatively well constrained and geological archives record responses over a range of timescales. Despite this, large uncertainties remain over the feedback loops that culminated in the collapse of the great Northern Hemisphere ice sheets, and a consensus has yet to be reached on the chains of events that led to rapid surface warming and cooling during this period.Climate models are powerful tools for quantitatively assessing these outstanding issues through their ability to temporally resolve cause and effect, as well as break down the contributions from different forcings. This is well demonstrated by pioneering work; for example by Liu et al. (2009), Roche et al. (2011), Gregoire et al. (2012) and Menviel et al. (2011). However, such work is not without challenges; model-geological data mismatches remain unsolved and it is difficult to compare results from different models with unique experiment designs. Therefore, we have established a multidisciplinary Paleoclimate Model Intercomparison Project working group to coordinate transient climate model simulations and geological archive compilations of the last deglaciation. Here, we present the plans and progress of the working group in its first phase of activity; the investigation of Heinrich Stadial 1 and the lead into the Bolling warming event. We describe the set-up of the core deglacial experiment, explain our approach for dealing with uncertain climate forcings and outline our solutions to challenges posed by this research. By defining a common experiment design, we have built a framework to include models of different speeds, complexities and resolution, maximising the reward of this varied approach. One of the next challenges is to compile transient proxy records and develop a methodology for dealing with uncertainty and error in model-geological data comparisons. Through this global and interdisciplinary initiative, we combine multi-proxy records with a suite of different modelling techniques to test hypotheses for abrupt climate changes and reconstruct the chain of events that deglaciated the Earth 21-9 ka.

Introduction to TETHYS—an interdisciplinary GIS database for studying continental collisions

NASA Astrophysics Data System (ADS)

Khan, S. D.; Flower, M. F. J.; Sultan, M. I.; Sandvol, E.

2006-05-01

The TETHYS GIS database is being developed as a way to integrate relevant geologic, geophysical, geochemical, geochronologic, and remote sensing data bearing on Tethyan continental plate collisions. The project is predicated on a need for actualistic model 'templates' for interpreting the Earth's geologic record. Because of their time-transgressive character, Tethyan collisions offer 'actualistic' models for features such as continental 'escape', collision-induced upper mantle flow magmatism, and marginal basin opening, associated with modern convergent plate margins. Large integrated geochemical and geophysical databases allow for such models to be tested against the geologic record, leading to a better understanding of continental accretion throughout Earth history. The TETHYS database combines digital topographic and geologic information, remote sensing images, sample-based geochemical, geochronologic, and isotopic data (for pre- and post-collision igneous activity), and data for seismic tomography, shear-wave splitting, space geodesy, and information for plate tectonic reconstructions. Here, we report progress on developing such a database and the tools for manipulating and visualizing integrated 2-, 3-, and 4-d data sets with examples of research applications in progress. Based on an Oracle database system, linked with ArcIMS via ArcSDE, the TETHYS project is an evolving resource for researchers, educators, and others interested in studying the role of plate collisions in the process of continental accretion, and will be accessible as a node of the national Geosciences Cyberinfrastructure Network—GEON via the World-Wide Web and ultra-high speed internet2. Interim partial access to the data and metadata is available at: http://geoinfo.geosc.uh.edu/Tethys/ and http://www.esrs.wmich.edu/tethys.htm. We demonstrate the utility of the TETHYS database in building a framework for lithospheric interactions in continental collision and accretion.

PCTO-SIM: Multiple-point geostatistical modeling using parallel conditional texture optimization

NASA Astrophysics Data System (ADS)

Pourfard, Mohammadreza; Abdollahifard, Mohammad J.; Faez, Karim; Motamedi, Sayed Ahmad; Hosseinian, Tahmineh

2017-05-01

Multiple-point Geostatistics is a well-known general statistical framework by which complex geological phenomena have been modeled efficiently. Pixel-based and patch-based are two major categories of these methods. In this paper, the optimization-based category is used which has a dual concept in texture synthesis as texture optimization. Our extended version of texture optimization uses the energy concept to model geological phenomena. While honoring the hard point, the minimization of our proposed cost function forces simulation grid pixels to be as similar as possible to training images. Our algorithm has a self-enrichment capability and creates a richer training database from a sparser one through mixing the information of all surrounding patches of the simulation nodes. Therefore, it preserves pattern continuity in both continuous and categorical variables very well. It also shows a fuzzy result in its every realization similar to the expected result of multi realizations of other statistical models. While the main core of most previous Multiple-point Geostatistics methods is sequential, the parallel main core of our algorithm enabled it to use GPU efficiently to reduce the CPU time. One new validation method for MPS has also been proposed in this paper.

Hydrogeologic Framework of Bedrock Units and Initial Salinity Distribution for a Simulation of Groundwater Flow for the Lake Michigan Basin

USGS Publications Warehouse

Lampe, David C.

2009-01-01

The U.S. Geological Survey is assessing groundwater availability in the Lake Michigan Basin. As part of the assessment, a variable-density groundwater-flow model is being developed to simulate the effects of groundwater use on water availability throughout the basin. The hydrogeologic framework for the Lake Michigan Basin model was developed by grouping the bedrock geology of the study area into hydrogeologic units on the basis of the functioning of each unit as an aquifer or confining layer within the basin. Available data were evaluated based on the areal extent of coverage within the study area, and procedures were established to characterize areas with sparse data coverage. Top and bottom altitudes for each hydrogeologic unit were interpolated in a geographic information system for input to the model and compared with existing maps of subsurface formations. Fourteen bedrock hydrogeologic units, making up 17 bedrock model layers, were defined, and they range in age from the Jurassic Period red beds of central Michigan to the Cambrian Period Mount Simon Sandstone. Information on groundwater salinity in the Lake Michigan Basin was compiled to create an input dataset for the variable-density groundwater-flow simulation. Data presented in this report are referred to as 'salinity data' and are reported in terms of total dissolved solids. Salinity data were not available for each hydrogeologic unit. Available datasets were assigned to a hydrogeologic unit, entered into a spatial database, and data quality was visually evaluated. A geographic information system was used to interpolate salinity distributions for each hydrogeologic unit with available data. Hydrogeologic units with no available data either were set equal to neighboring units or were vertically interpolated by use of values from units above and below.

Coal and coalbed-methane resources in the Appalachian and Black Warrior basins: maps showing the distribution of coal fields, coal beds, and coalbed-methane fields: Chapter D.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Trippi, Michael H.; Ruppert, Leslie F.; Milici, Robert C.; Kinney, Scott A.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The study area for most reports in this volume is the Appalachian basin. The term “Appalachian basin study area” (shortened from “Appalachian basin geologic framework study area”) includes all of the Appalachian Basin Province (Province 67) and part of the neighboring Black Warrior Basin Province (Province 65) of Dolton and others (1995). The boundaries for these two provinces and the study area are shown on figure 1.

Health, Safety, and Environmental Screening and Ranking Frameworkfor Geologic CO2 Storage Site Selection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oldenburg, Curtis M.

2006-03-15

This report describes a screening and ranking framework(SRF) developed to evaluate potential geologic carbon dioxide (CO2)storage sites on the basis of health, safety, and environmental (HSE)risk arising from possible CO2 leakage. The approach is based on theassumption that HSE risk due to CO2 leakage is dependent on three basiccharacteristics of a geologic CO2 storage site: (1) the potential forprimary containment by the target formation, (2) the potential forsecondary containment if the primary formation leaks, and (3) thepotential for attenuation and dispersion of leaking CO2 if the primaryformation leaks and secondary containment fails. The framework isimplemented in a spreadsheet in whichmore » users enter numerical scoresrepresenting expert opinions or general information available frompublished materials along with estimates of uncertainty to evaluate thethree basic characteristics in order to screen and rank candidate sites.Application of the framework to the Rio Vista Gas Field, Ventura OilField, and Mammoth Mountain demonstrates the approach. Refinements andextensions are possible through the use of more detailed data or modelresults in place of property proxies. Revisions and extensions to improvethe approach are anticipated in the near future as it is used and testedby colleagues and collaborators.« less

Modelling fully-coupled Thermo-Hydro-Mechanical (THM) processes in fractured reservoirs using GOLEM: a massively parallel open-source simulator

NASA Astrophysics Data System (ADS)

Jacquey, Antoine; Cacace, Mauro

2017-04-01

Utilization of the underground for energy-related purposes have received increasing attention in the last decades as a source for carbon-free energy and for safe storage solutions. Understanding the key processes controlling fluid and heat flow around geological discontinuities such as faults and fractures as well as their mechanical behaviours is therefore of interest in order to design safe and sustainable reservoir operations. These processes occur in a naturally complex geological setting, comprising natural or engineered discrete heterogeneities as faults and fractures, span a relatively large spectrum of temporal and spatial scales and they interact in a highly non-linear fashion. In this regard, numerical simulators have become necessary in geological studies to model coupled processes and complex geological geometries. In this study, we present a new simulator GOLEM, using multiphysics coupling to characterize geological reservoirs. In particular, special attention is given to discrete geological features such as faults and fractures. GOLEM is based on the Multiphysics Object-Oriented Simulation Environment (MOOSE). The MOOSE framework provides a powerful and flexible platform to solve multiphysics problems implicitly and in a tightly coupled manner on unstructured meshes which is of interest for the considered non-linear context. Governing equations in 3D for fluid flow, heat transfer (conductive and advective), saline transport as well as deformation (elastic and plastic) have been implemented into the GOLEM application. Coupling between rock deformation and fluid and heat flow is considered using theories of poroelasticity and thermoelasticity. Furthermore, considering material properties such as density and viscosity and transport properties such as porosity as dependent on the state variables (based on the International Association for the Properties of Water and Steam models) increase the coupling complexity of the problem. The GOLEM application aims therefore at integrating more physical processes observed in the field or in the laboratory to simulate more realistic scenarios. The use of high-level nonlinear solver technology allow us to tackle these complex multiphysics problems in three dimensions. Basic concepts behing the GOLEM simulator will be presented in this study as well as a few application examples to illustrate its main features.

Geologic map of the Middletown quadrangle, Frederick, Shenandoah, and Warren Counties, Virginia

USGS Publications Warehouse

Orndorff, Randall C.; Epstein, Jack Burton; McDowell, Robert C.

1999-01-01

The Middletown 1:24,000-scale quadrangle is one of several quadrangles in Frederick County, Virginia mapped or being mapped by geologists from the U.S. Geological Survey in Reston, VA with funding from the National Cooperative Geologic Mapping Program. This map was originally published as a paper product in 1999. It has been converted to GIS-based digital form. This work is part of a project being lead by the U.S. Geological Survey Water Resources Discipline, Virginia District, to investigate the geologic framework and groundwater resources of Frederick County as well as other areas in the northern Shenandoah Valley of Virginia and West Virginia. For more information about the Project see: http://geology.er.usgs.gov/eespteam/Karst/index.html for Geologic Discipline efforts and http://va.water.usgs.gov/va134/index.htm for Water Resources Discipline efforts.

Benchmarking hydrological model predictive capability for UK River flows and flood peaks.

NASA Astrophysics Data System (ADS)

Lane, Rosanna; Coxon, Gemma; Freer, Jim; Wagener, Thorsten

2017-04-01

Data and hydrological models are now available for national hydrological analyses. However, hydrological model performance varies between catchments, and lumped, conceptual models are not able to produce adequate simulations everywhere. This study aims to benchmark hydrological model performance for catchments across the United Kingdom within an uncertainty analysis framework. We have applied four hydrological models from the FUSE framework to 1128 catchments across the UK. These models are all lumped models and run at a daily timestep, but differ in the model structural architecture and process parameterisations, therefore producing different but equally plausible simulations. We apply FUSE over a 20 year period from 1988-2008, within a GLUE Monte Carlo uncertainty analyses framework. Model performance was evaluated for each catchment, model structure and parameter set using standard performance metrics. These were calculated both for the whole time series and to assess seasonal differences in model performance. The GLUE uncertainty analysis framework was then applied to produce simulated 5th and 95th percentile uncertainty bounds for the daily flow time-series and additionally the annual maximum prediction bounds for each catchment. The results show that the model performance varies significantly in space and time depending on catchment characteristics including climate, geology and human impact. We identify regions where models are systematically failing to produce good results, and present reasons why this could be the case. We also identify regions or catchment characteristics where one model performs better than others, and have explored what structural component or parameterisation enables certain models to produce better simulations in these catchments. Model predictive capability was assessed for each catchment, through looking at the ability of the models to produce discharge prediction bounds which successfully bound the observed discharge. These results improve our understanding of the predictive capability of simple conceptual hydrological models across the UK and help us to identify where further effort is needed to develop modelling approaches to better represent different catchment and climate typologies.

Estimating and mapping ecological processes influencing microbial community assembly

DOE PAGES

Stegen, James C.; Lin, Xueju; Fredrickson, Jim K.; ...

2015-05-01

Ecological community assembly is governed by a combination of (i) selection resulting from among-taxa differences in performance; (ii) dispersal resulting from organismal movement; and (iii) ecological drift resulting from stochastic changes in population sizes. The relative importance and nature of these processes can vary across environments. Selection can be homogeneous or variable, and while dispersal is a rate, we conceptualize extreme dispersal rates as two categories; dispersal limitation results from limited exchange of organisms among communities, and homogenizing dispersal results from high levels of organism exchange. To estimate the influence and spatial variation of each process we extend a recentlymore » developed statistical framework, use a simulation model to evaluate the accuracy of the extended framework, and use the framework to examine subsurface microbial communities over two geologic formations. For each subsurface community we estimate the degree to which it is influenced by homogeneous selection, variable selection, dispersal limitation, and homogenizing dispersal. Our analyses revealed that the relative influences of these ecological processes vary substantially across communities even within a geologic formation. We further identify environmental and spatial features associated with each ecological process, which allowed mapping of spatial variation in ecological-process-influences. The resulting maps provide a new lens through which ecological systems can be understood; in the subsurface system investigated here they revealed that the influence of variable selection was associated with the rate at which redox conditions change with subsurface depth.« less

Model Fusion Tool - the Open Environmental Modelling Platform Concept

NASA Astrophysics Data System (ADS)

Kessler, H.; Giles, J. R.

2010-12-01

The vision of an Open Environmental Modelling Platform - seamlessly linking geoscience data, concepts and models to aid decision making in times of environmental change. Governments and their executive agencies across the world are facing increasing pressure to make decisions about the management of resources in light of population growth and environmental change. In the UK for example, groundwater is becoming a scarce resource for large parts of its most densely populated areas. At the same time river and groundwater flooding resulting from high rainfall events are increasing in scale and frequency and sea level rise is threatening the defences of coastal cities. There is also a need for affordable housing, improved transport infrastructure and waste disposal as well as sources of renewable energy and sustainable food production. These challenges can only be resolved if solutions are based on sound scientific evidence. Although we have knowledge and understanding of many individual processes in the natural sciences it is clear that a single science discipline is unable to answer the questions and their inter-relationships. Modern science increasingly employs computer models to simulate the natural, economic and human system. Management and planning requires scenario modelling, forecasts and ‘predictions’. Although the outputs are often impressive in terms of apparent accuracy and visualisation, they are inherently not suited to simulate the response to feedbacks from other models of the earth system, such as the impact of human actions. Geological Survey Organisations (GSO) are increasingly employing advances in Information Technology to visualise and improve their understanding of geological systems. Instead of 2 dimensional paper maps and reports many GSOs now produce 3 dimensional geological framework models and groundwater flow models as their standard output. Additionally the British Geological Survey have developed standard routines to link geological data to groundwater models but these models are only aimed at solving one specific part of the earth’s system, e.g. the flow of groundwater to an abstraction borehole or the availability of water for irrigation. Particular problems arise when model data from two or more disciplines are incompatible in terms of data formats, scientific concepts or language. Other barriers include the cultural segregation within and between science disciplines as well as impediments to data exchange due to ownership and copyright restrictions. OpenMI and GeoSciML are initiatives that are trying to overcome these barriers by building international communities that share vocabularies and data formats. This paper gives examples of the successful merging of geological and hydrological models from the UK and will introduce the vision of an open Environmental Modelling Platform which aims to link data, knowledge and concepts seamlessly to numerical process models. Last but not least there is an urgent need to create a Subsurface Information System akin to a Geographic Information System in which all results of subsurface modelling can be visualised and analysed in an integrated manner and thereby become useful for decision makers.

Marine geophysical data collected in a shallow back-barrier estuary, Barnegat Bay, New Jersey

USGS Publications Warehouse

Andrews, Brian D.; Miselis, Jennifer L.; Danforth, William W.; Irwin, Barry J.; Worley, Charles R.; Bergeron, Emile M.; Blackwood, Dann S.

2015-06-26

In 2011, the U.S. Geological Survey, in cooperation with the New Jersey Department of Environmental Protection, began a multidisciplinary research project to better understand the water quality in Barnegat Bay, New Jersey. This back-barrier estuary is experiencing degraded water quality, algal blooms, loss of seagrass, and increases in oxygen stress, macroalgae, stinging nettles, and brown tide. The spatial scale of the estuary and the scope of challenges within it necessitate a multidisciplinary approach that includes establishing the regional geology and the estuary’s physical characteristics and modeling how the estuary’s morphology interacts to affect its water quality. This report presents the data collected during this project for use in understanding the morphology and the distribution of sea-floor and sub-sea-floor sediments within Barnegat Bay, describes the methods used to collect and process those data, and includes links to the final processed datasets. These data can be used by scientists to understand the links between geomorphology, geologic framework, sediment transport, and estuarine water quality and circulation.

Questa baseline and pre-mining ground-water quality investigation. 10. Geologic influences on ground and surface waters in the lower Red River watershed, New Mexico

USGS Publications Warehouse

Ludington, Steve; Plumlee, Geoff; Caine, Jonathan S.; Bove, Dana; Holloway, JoAnn; Livo, Eric

2005-01-01

Introduction: This report is one in a series that presents results of an interdisciplinary U.S. Geological Survey (USGS) study of ground-water quality in the lower Red River watershed prior to open-pit and underground molybdenite mining at Molycorp's Questa mine. The stretch of the Red River watershed that extends from just upstream of the town of Red River, N. Mex., to just above the town of Questa includes several mineralized areas in addition to the one mined by Molycorp. Natural erosion and weathering of pyrite-rich rocks in the mineralized areas has created a series of erosional scars along this stretch of the Red River that contribute acidic waters, as well as mineralized alluvial material and sediments, to the river. The overall goal of the USGS study is to infer the premining ground-water quality at the Molycorp mine site. An integrated geologic, hydrologic, and geochemical model for ground water in the mineralized-but unmined-Straight Creek drainage (a tributary of the Red River) is being used as an analog for the geologic, geochemical, and hydrologic conditions that influenced ground-water quality and quantity in the Red River drainage prior to mining. This report provides an overall geologic framework for the Red River watershed between Red River and Questa, in northern New Mexico, and summarizes key geologic, mineralogic, structural and other characteristics of various mineralized areas (and their associated erosional scars and debris fans) that likely influence ground- and surface-water quality and hydrology. The premining nature of the Sulphur Gulch and Goat Hill Gulch scars on the Molycorp mine site can be inferred through geologic comparisons with other unmined scars in the Red River drainage.

Geology of the surficial aquifer system, Dade County, Florida; lithologic logs

USGS Publications Warehouse

Causaras, C.R.

1986-01-01

The geologic framework of the surficial aquifer system in Dade County, Florida, was investigated as part of a longterm study by the USGS in cooperation with the South Florida Water Management District, to describe the geology, hydrologic characteristics, and groundwater quality of the surficial aquifer system. Thirty-three test wells were drilled completely through the surficial aquifer system and into the underlying, relatively impermeable units of the Tamiami and Hawthorn Formations. Detailed lithologic logs were made from microscopic examination of rock cuttings and cores obtained from these wells. The logs were used to prepare geologic sections that show the lithologic variations, thickness of the lithologic units, and different geologic formations that comprise the aquifers system. (Author 's abstract)

GeoloGIS-BH: An Information System for Using the Built Heritage for Geological Teaching

ERIC Educational Resources Information Center

Alves, C.; Ribeiro, Vitor; Cunha, Marta; Pereira, Paula; Pinto, Cláudia

2016-01-01

There are examples of using stones of the cultural heritage for teaching purposes. Information systems have found several potential uses in the promotion and preservation of cultural heritage. In this paper is considered the conceptual framework of an information system concerning features of geological interest (FGI) in the built heritage…

Contaminant transport and accumulation in Massachusetts Bay and Boston Harbor; a summary of U.S. Geological Survey studies

USGS Publications Warehouse

Butman, Bradford; Bothner, Michael H.; Hathaway, J.C.; Jenter, H.L.; Knebel, H.J.; Manheim, F.T.; Signell, R.P.

1992-01-01

The U.S. Geological Survey (USGS) is conducting studies in Boston Harbor, Massachusetts Bay, and Cape Cod Bay designed to define the geologic framework of the region and to understand the transport and accumulation of contaminated sediments. The region is being studied because of environmental problems caused by the introduction of wastes for a long time, because a new ocean outfall (to begin operation in 1995) will change the location for disposal of treated Boston sewage from Boston Harbor into Massachusetts Bay, and because of the need to understand the transport of sediments and associated contaminants in order to address a wide range of management questions. The USGS effort complements and is closely coordinated with the research and monitoring studies supported by the Massachusetts Environmental Trust, the Massachusetts Bays Program, and by the Massachusetts Water Resources Authority. The USGS study includes (1) geologic mapping, (2) circulation studies, (3) long-term current and sediment transport observations, (4) measurements of contaminant inventories and rates of sediment mixing and accumulation, (5) circulation modeling, (6) development of a contaminated sediments data base, and (7) information exchange. A long-term objective of the program is to develop a predictive capability for sediment transport and accumulation.

Sex Education Representations in Spanish Combined Biology and Geology Textbooks

NASA Astrophysics Data System (ADS)

García-Cabeza, Belén; Sánchez-Bello, Ana

2013-07-01

Sex education is principally dealt with as part of the combined subject of Biology and Geology in the Spanish school curriculum. Teachers of this subject are not specifically trained to teach sex education, and thus the contents of their assigned textbooks are the main source of information available to them in this field. The main goal of this study was to determine what information Biology and Geology textbooks provide with regard to sex education and the vision of sexuality they give, but above all to reveal which perspectives of sex education they legitimise and which they silence. We analysed the textbooks in question by interpreting both visual and text representations, as a means of enabling us to investigate the nature of the discourse on sex education. With this aim, we have used a qualitative methodology, based on the content analysis. The main analytical tool was an in-house grid constructed to allow us to analyse the visual and textual representations. Our analysis of the combined Biology and Geology textbooks for Secondary Year 3 revealed that there is a tendency to reproduce models of sex education that take place within a framework of the more traditional discourses. Besides, the results suggested that the most of the sample chosen for this study makes a superficial, incomplete, incorrect or biased approach to sex education.

Dynamic simulations of geologic materials using combined FEM/DEM/SPH analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, J P; Johnson, S M

2008-03-26

An overview of the Lawrence Discrete Element Code (LDEC) is presented, and results from a study investigating the effect of explosive and impact loading on geologic materials using the Livermore Distinct Element Code (LDEC) are detailed. LDEC was initially developed to simulate tunnels and other structures in jointed rock masses using large numbers of polyhedral blocks. Many geophysical applications, such as projectile penetration into rock, concrete targets, and boulder fields, require a combination of continuum and discrete methods in order to predict the formation and interaction of the fragments produced. In an effort to model this class of problems, LDECmore » now includes implementations of Cosserat point theory and cohesive elements. This approach directly simulates the transition from continuum to discontinuum behavior, thereby allowing for dynamic fracture within a combined finite element/discrete element framework. In addition, there are many application involving geologic materials where fluid-structure interaction is important. To facilitate solution of this class of problems a Smooth Particle Hydrodynamics (SPH) capability has been incorporated into LDEC to simulate fully coupled systems involving geologic materials and a saturating fluid. We will present results from a study of a broad range of geomechanical problems that exercise the various components of LDEC in isolation and in tandem.« less

Burial and thermal history of the central Appalachian basin, based on three 2-D models of Ohio, Pennsylvania, and West Virginia

USGS Publications Warehouse

Rowan, Elisabeth L.

2006-01-01

Introduction: Three regional-scale, cross sectional (2-D) burial and thermal history models are presented for the central Appalachian basin based on the detailed geologic cross sections of Ryder and others (2004), Crangle and others (2005), and Ryder, R.T., written communication. The models integrate the available thermal and geologic information to constrain the burial, uplift, and erosion history of the region. The models are restricted to the relatively undeformed part of the basin and extend from the Rome trough in West Virginia and Pennsylvania northwestward to the Findlay arch in Ohio. This study expands the scope of previous work by Rowan and others (2004) which presented a preliminary burial/thermal history model for a cross section (E-E') through West Virginia and Ohio. In the current study, the burial/thermal history model for E-E' is revised, and integrated with results of two additional cross sectional models (D-D' and C-C'). The burial/thermal history models provide calculated thermal maturity (Ro%) values for the entire stratigraphic sequence, including hydrocarbon source rocks, along each of the three cross sections. In contrast, the Ro and conodont CAI data available in the literature are sparse and limited to specific stratigraphic intervals. The burial/thermal history models also provide the regional temperature and pressure framework that is needed to model hydrocarbon migration.

Petroleum system modeling capabilities for use in oil and gas resource assessments

USGS Publications Warehouse

Higley, Debra K.; Lewan, Michael; Roberts, Laura N.R.; Henry, Mitchell E.

2006-01-01

Summary: Petroleum resource assessments are among the most highly visible and frequently cited scientific products of the U.S. Geological Survey. The assessments integrate diverse and extensive information on the geologic, geochemical, and petroleum production histories of provinces and regions of the United States and the World. Petroleum systems modeling incorporates these geoscience data in ways that strengthen the assessment process and results are presented visually and numerically. The purpose of this report is to outline the requirements, advantages, and limitations of one-dimensional (1-D), two-dimensional (2-D), and three-dimensional (3-D) petroleum systems modeling that can be applied to the assessment of oil and gas resources. Primary focus is on the application of the Integrated Exploration Systems (IES) PetroMod? software because of familiarity with that program as well as the emphasis by the USGS Energy Program on standardizing to one modeling application. The Western Canada Sedimentary Basin (WCSB) is used to demonstrate the use of the PetroMod? software. Petroleum systems modeling quantitatively extends the 'total petroleum systems' (TPS) concept (Magoon and Dow, 1994; Magoon and Schmoker, 2000) that is employed in USGS resource assessments. Modeling allows integration of state-of-the-art analysis techniques, and provides the means to test and refine understanding of oil and gas generation, migration, and accumulation. Results of modeling are presented visually, numerically, and statistically, which enhances interpretation of the processes that affect TPSs through time. Modeling also provides a framework for the input and processing of many kinds of data essential in resource assessment, including (1) petroleum system elements such as reservoir, seal, and source rock intervals; (2) timing of depositional, hiatus, and erosional events and their influences on petroleum systems; (3) incorporation of vertical and lateral distribution and lithologies of strata that compose the petroleum systems; and (4) calculations of pressure-volume-temperature (PVT) histories. As digital data on petroleum systems continue to expand, the models can integrate these data into USGS resource assessments by building and displaying, through time, areas of petroleum generation, migration pathways, accumulations, and relative contributions of source rocks to the hydrocarbon components. IES PetroMod? 1-D, 2-D, and 3-D models are integrated such that each uses the same variables for petroleum systems modeling. 1-D burial history models are point locations, mainly wells. Maps and cross-sections model geologic information in two dimensions and can incorporate direct input of 2-D seismic data and interpretations using various formats. Both 1-D and 2-D models use data essential for assessments and, following data compilation, they can be completed in hours and retested in minutes. Such models should be built early in the geologic assessment process, inasmuch as they incorporate the petroleum system elements of reservoir, source, and seal rock intervals with associated lithologies and depositional and erosional ages. The models can be used to delineate the petroleum systems. A number of 1-D and 2-D models can be constructed across a geologic province and used by the assessment geologists as a 3-D framework of processes that control petroleum generation, migration, and accumulation. The primary limitation of these models is that they only represent generation, migration, and accumulation in two dimensions. 3-D models are generally built at reservoir to basin scales. They provide a much more detailed and realistic representation of petroleum systems than 1-D or 2-D models because they portray more fully the temporal and physical relations among (1) burial history; (2) lithologies and associated changes through burial in porosity, permeability, and compaction; (3) hydrodynamic effects; and (4) other parameters that influence petroleum gen

Hydrologic and geologic characteristics of the Yucca Mountain site relevant to the performance of a potential repository: Day 1, Las Vegas, Nevada to Pahrump, Nevada: Stop 6A. Keane Wonder Spring and regional groundwater flow in the Death Valley region

USGS Publications Warehouse

Steinkampf, W.C.

2000-01-01

Yucca Mountain, located ~100 mi northwest of Las Vegas, Nevada, has been designated by Congress as a site to be characterized for a potential mined geologic repository for high-level radioactive waste. This field trip will examine the regional geologic and hydrologic setting for Yucca Mountain, as well as specific results of the site characterization program, The first day focuses on the regional seeing with emphasis on current and paleo hydrology, which are both of critical concern for predicting future performance of a potential repository. Morning stops will be in southern Nevada and afternoon stops will be in Death Valley. The second day will be spent at Yucca Mountain. The filed trip will visit the underground testing sites in the "Exploratory Studies Facility" and the "Busted Butte Unsaturated Zone Transport Field Test" plus several surface-based testing sites. Much of the work at the site has concentrated on studies of the unsaturated zone, and element of the hydrologic system that historically has received little attention. Discussions during the second day will comprise selected topics of Yucca Mountain geology, mic hazard in the Yucca Mountain area. Evening discussions will address modeling of regional groundwater flow, the geology and hydrology of Yucca Mountain to the performance of a potential repository. Day 3 will examine the geologic framework and hydrology of the Pahute Mesa-Oasis Valley Groundwater Basin and then will continue to Reno via Hawthorne, Nevada and the Walker Lake area.

Spatially explicit land-use and land-cover scenarios for the Great Plains of the United States

USGS Publications Warehouse

Sohl, Terry L.; Sleeter, Benjamin M.; Sayler, Kristi L.; Bouchard, Michelle A.; Reker, Ryan R.; Bennett, Stacie L.; Sleeter, Rachel R.; Kanengieter, Ronald L.; Zhu, Zhi-Liang

2012-01-01

The Great Plains of the United States has undergone extensive land-use and land-cover change in the past 150 years, with much of the once vast native grasslands and wetlands converted to agricultural crops, and much of the unbroken prairie now heavily grazed. Future land-use change in the region could have dramatic impacts on ecological resources and processes. A scenario-based modeling framework is needed to support the analysis of potential land-use change in an uncertain future, and to mitigate potentially negative future impacts on ecosystem processes. We developed a scenario-based modeling framework to analyze potential future land-use change in the Great Plains. A unique scenario construction process, using an integrated modeling framework, historical data, workshops, and expert knowledge, was used to develop quantitative demand for future land-use change for four IPCC scenarios at the ecoregion level. The FORE-SCE model ingested the scenario information and produced spatially explicit land-use maps for the region at relatively fine spatial and thematic resolutions. Spatial modeling of the four scenarios provided spatial patterns of land-use change consistent with underlying assumptions and processes associated with each scenario. Economically oriented scenarios were characterized by significant loss of natural land covers and expansion of agricultural and urban land uses. Environmentally oriented scenarios experienced modest declines in natural land covers to slight increases. Model results were assessed for quantity and allocation disagreement between each scenario pair. In conjunction with the U.S. Geological Survey's Biological Carbon Sequestration project, the scenario-based modeling framework used for the Great Plains is now being applied to the entire United States.

Middle school students' understanding of the natural history of the Earth and life on Earth as a function of deep time

NASA Astrophysics Data System (ADS)

Pulling, Azalie Cecile

The purpose of this study was to use deep time, that is geologic time as a mechanism to explore middle school students' understanding of the natural history of the earth and the evolution of life on earth. Geologic time is a logical precursor to middle school students' understanding of biological evolution. This exploratory, mixed model study used qualitative and quantitative methods in each stage of the research to explore sixth grade students, understanding of geologic time, their worldviews (e.g., conceptual ecology), and conceptual change. The study included fifty-nine students in the large group study and four case studies. The primary data collection instrument was the Geologic Timeline Survey. Additional data collection instruments and methods (e.g., concept evaluation statement, journal entries, word associations, interviews, and formal tests) were used to triangulate the study findings. These data were used to create narrative modal profiles of the categories of student thinking that emerged from the large group analysis: Middle School (MS) Scientists (correct science), MS Protoscientists (approaching correct science), MS Prescientists (dinosaur understanding), and MS Pseudoscientists (fundamental religious understanding). Case studies were used to provide a thick description of each category. This study discovered a pattern of student thinking about geologic time that moved along a knowledge continuum from pseudoscience (fundamental creationist understanding) to prescience (everyday-science understanding) to science (correct or approaching correct science). The researcher described the deep-seated misconceptions produced by the prescience thinking level, e.g., dinosaur misconceptions, and cautioned the science education community about using dinosaurs as a glamour-science topic. The most limiting conceptual frameworks found in this study were prescience (a dinosaur focus) and pseudoscience (a fundamental religious focus). An understanding of geologic time as Piaget's system of time (e.g., chronological ordering of events, before and after relationships, duration or evolutionary time) was a necessary conceptual framework for students to develop a scientific understanding of deep time. An examination of students, worldviews and the interface of science and religion indicated that students often successfully applied a demarcation between science and religion in their public thinking (e.g., the formal classroom setting), but in their private thinking, the demarcation was often blurred.

Estimation of Groundwater Recharge in a Japanese Headwater Area by Intensive Collaboration of Field Survey and Modelling Work

NASA Astrophysics Data System (ADS)

Yano, S.; Kondo, H.; Tawara, Y.; Yamada, T.; Mori, K.; Yoshida, A.; Tada, K.; Tsujimura, M.; Tokunaga, T.

2017-12-01

It is important to understand groundwater systems, including their recharge, flow, storage, discharge, and withdrawal, so that we can use groundwater resources efficiently and sustainably. To examine groundwater recharge, several methods have been discussed based on water balance estimation, in situ experiments, and hydrological tracers. However, few studies have developed a concrete framework for quantifying groundwater recharge rates in an undefined area. In this study, we established a robust method to quantitatively determine water cycles and estimate the groundwater recharge rate by combining the advantages of field surveys and model simulations. We replicated in situ hydrogeological observations and three-dimensional modeling in a mountainous basin area in Japan. We adopted a general-purpose terrestrial fluid-flow simulator (GETFLOWS) to develop a geological model and simulate the local water cycle. Local data relating to topology, geology, vegetation, land use, climate, and water use were collected from the existing literature and observations to assess the spatiotemporal variations of the water balance from 2011 to 2013. The characteristic structures of geology and soils, as found through field surveys, were parameterized for incorporation into the model. The simulated results were validated using observed groundwater levels and resulted in a Nash-Sutcliffe Model Efficiency Coefficient of 0.92. The results suggested that local groundwater flows across the watershed boundary and that the groundwater recharge rate, defined as the flux of water reaching the local unconfined groundwater table, has values similar to the level estimated in the `the lower soil layers on a long-term basis. This innovative method enables us to quantify the groundwater recharge rate and its spatiotemporal variability with high accuracy, which contributes to establishing a foundation for sustainable groundwater management.

Geologic framework influences on the geomorphology of an anthropogenically modified barrier island: Assessment of dune/beach changes at Fire Island, New York

USGS Publications Warehouse

Lentz, E.E.; Hapke, C.J.

2011-01-01

Antecedent geology plays a crucial role in determining the inner-shelf, nearshore, and onshore geomorphology observed in coastal systems. However, the influence of the geologic framework on a system is difficult to extract when evaluating responses to changes due to storms and anthropogenic modifications, and few studies have quantified the potential for these influences in dune/beach environments. This study evaluates topographic change to the dune/beach system at Fire Island, New York over a ten year period (1998-2008) at two sites representing eastern and western reaches of the island where morphology has been shown to vary. The sites are situated along swaths of coast eroding differentially and where the inner shelf geologic framework differs substantially. Fewer large storms occurred in the first half of the study period, compared with the later part of the study period which includes several severe and prolonged extratropical storms. Additionally, a major beach replenishment project was conducted at one of the study sites. Topographic data from LiDAR and RTK GPS surveys are used to construct high-resolution 3D surfaces, which are used to determine volumetric change and to extract 2D alongshore features and profiles for analysis. The study sites help to further characterize morphologic differences between eastern and western reaches of the island. The western site displays higher sand volumes, lower dunes, and a lower gradient profile slope when compared with the eastern site. In addition to these fundamental morphologic differences, the two sites also differ significantly in their response to coastal storms and in the fact that their replenishment histories are different. The replenished areas show reduced vulnerability to storms through minimal volume loss and shoreline accretion that should be considered when evaluating the response of replenished areas to episodic events. We propose that site-specific differences evident throughout the study period can be linked to alongshore variations in the framework geology of the system. Anthropogenic modifications may have intensified differences already inherent in the system. ?? 2010 Elsevier B.V.

Deep Borehole Disposal Safety Analysis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Freeze, Geoffrey A.; Stein, Emily; Price, Laura L.

This report presents a preliminary safety analysis for the deep borehole disposal (DBD) concept, using a safety case framework. A safety case is an integrated collection of qualitative and quantitative arguments, evidence, and analyses that substantiate the safety, and the level of confidence in the safety, of a geologic repository. This safety case framework for DBD follows the outline of the elements of a safety case, and identifies the types of information that will be required to satisfy these elements. At this very preliminary phase of development, the DBD safety case focuses on the generic feasibility of the DBD concept.more » It is based on potential system designs, waste forms, engineering, and geologic conditions; however, no specific site or regulatory framework exists. It will progress to a site-specific safety case as the DBD concept advances into a site-specific phase, progressing through consent-based site selection and site investigation and characterization.« less

Using Uncertainty Quantification to Guide Development and Improvements of a Regional-Scale Model of the Coastal Lowlands Aquifer System Spanning Texas, Louisiana, Mississippi, Alabama and Florida

NASA Astrophysics Data System (ADS)

Foster, L. K.; Clark, B. R.; Duncan, L. L.; Tebo, D. T.; White, J.

2017-12-01

Several historical groundwater models exist within the Coastal Lowlands Aquifer System (CLAS), which spans the Gulf Coastal Plain in Texas, Louisiana, Mississippi, Alabama, and Florida. The largest of these models, called the Gulf Coast Regional Aquifer System Analysis (RASA) model, has been brought into a new framework using the Newton formulation for MODFLOW-2005 (MODFLOW-NWT) and serves as the starting point of a new investigation underway by the U.S. Geological Survey to improve understanding of the CLAS and provide predictions of future groundwater availability within an uncertainty quantification (UQ) framework. The use of an UQ framework will not only provide estimates of water-level observation worth, hydraulic parameter uncertainty, boundary-condition uncertainty, and uncertainty of future potential predictions, but it will also guide the model development process. Traditionally, model development proceeds from dataset construction to the process of deterministic history matching, followed by deterministic predictions using the model. This investigation will combine the use of UQ with existing historical models of the study area to assess in a quantitative framework the effect model package and property improvements have on the ability to represent past-system states, as well as the effect on the model's ability to make certain predictions of water levels, water budgets, and base-flow estimates. Estimates of hydraulic property information and boundary conditions from the existing models and literature, forming the prior, will be used to make initial estimates of model forecasts and their corresponding uncertainty, along with an uncalibrated groundwater model run within an unconstrained Monte Carlo analysis. First-Order Second-Moment (FOSM) analysis will also be used to investigate parameter and predictive uncertainty, and guide next steps in model development prior to rigorous history matching by using PEST++ parameter estimation code.

The geology of Six Mile Reef, eastern Long Island Sound

USGS Publications Warehouse

Poppe, L.J.; Denny, J.F.; Williams, S.J.; Moser, M.S.; Forfinski, N.A.; Stewart, H.F.; Doran, E.F.

2007-01-01

Digital terrain models, which can be produced from multibeam bathymetric data, are ordered arrays of depths for a number of sea-floor positions sampled at regularly spaced intervals. These models provide valuable base maps for marine geological interpretations that help define the variability of the sea floor (one of the primary controls of benthic habitat diversity), improve our understanding of the processes that control the distribution and transport of bottom sediments and the distribution of benthic habitats, and provide a detailed framework to guide and assist future research, monitoring, and management activities. The bathymetry interpreted herein was processed from data collected by National Oceanic and Atmospheric Administration vessels during hydrographic surveys H11361 and H11252. These surveys mapped roughly 156 km² of sea floor in the vicinity of Six Mile Reef, an area of eastern Long Island Sound where the sea floor is characterized by fields of large sand waves and an east-west decreasing gradient of bottom tidal-current speeds (fig. 1). Interpretations of the bathymetry are supplemented by concurrently collected seismic reflection data, as well as archived historic seismic profiles, sediment samples and bottom photography collected as part of a long-standing geologic mapping partnership between the State of Connecticut and the U.S. Geological Survey (fig. 2). The purpose of this digital report is 1) to provide the acoustic data layers produced during the above mentioned surveys, 2) to use them to describe the sea-floor character and bedform morphologies near Six Mile Reef, and 3) to relate these descriptions to ongoing processes and sedimentary environments.

Determination of Cenozoic sedimentary structures using integrated geophysical surveys: A case study in the Barkol Basin, Xinjiang, China

NASA Astrophysics Data System (ADS)

Sun, Kai; Chen, Chao; Du, Jinsong; Wang, Limin; Lei, Binhua

2018-01-01

Thickness estimation of sedimentary basin is a complex geological problem, especially in an orogenic environment. Intense and multiple tectonic movements and climate changes result in inhomogeneity of sedimentary layers and basement configurations, which making sedimentary structure modelling difficult. In this study, integrated geophysical methods, including gravity, magnetotelluric (MT) sounding and electrical resistivity tomography (ERT), were used to estimate basement relief to understand the geological structure and evolution of the eastern Barkol Basin in China. This basin formed with the uplift of the eastern Tianshan during the Cenozoic. Gravity anomaly map revealed the framework of the entire area, and ERT as well as MT sections reflected the geoelectric features of the Cenozoic two-layer distribution. Therefore, gravity data, constrained by MT, ERT and boreholes, were utilized to estimate the spatial distribution of the Quaternary layer. The gravity effect of the Quaternary layer related to the Tertiary layer was later subtracted to obtain the residual anomaly for inversion. For the Tertiary layer, the study area was divided into several parts because of lateral difference of density contrasts. Gravity data were interpreted to determine the density contrast constrained by the MT results. The basement relief can be verified by geological investigation, including the uplift process and regional tectonic setting. The agreement between geophysical survey and prior information from geology emphasizes the importance of integrated geophysical survey as a complementary means of geological studies in this region.

Surficial geology, structure, and thickness of selected geohydrologic units in the Columbia Plateau, Washington

USGS Publications Warehouse

Drost, B.W.; Whiteman, K.J.

1986-01-01

A 2-1/2 year study of the Columbia Plateau in Washington was begun in March 1982 to define spatial and temporal variations in dissolved sodium in the Columbia River Basalt Group aquifers and to relate these variations to the groundwater system and its geologic framework. This report describes the geologic framework , including the vertical and areal extent of the major basalt units, interbeds, and overlying materials. Thickness and structure of the Grande Ronde, Wanapum, and Saddle Mountains Basalts, thickness of the interbeds between the Grande Ronde and Wanapum, and Wanapum and Saddle Mountains Basalts, and thickness of the overburden were mapped at a scale of 1:500,000. Information was compiled from 2,500 well records using chemical analyses of core or drill chips, geophysical logs, and driller 's logs, in decreasing order of reliability. Surficial geology and surficial expression of structural features were simplified from published maps to provide maps with this information at the 1:500,000 scale. This report is intended to serve as a base for evaluating the distribution of dissolved sodium in basalt aquifers and as a base for future water resource studies. (USGS)

Subsurface and Surface Characterization using an Information Framework Model

NASA Astrophysics Data System (ADS)

Samuel-Ojo, Olusola

Groundwater plays a critical dual role as a reservoir of fresh water for human consumption and as a cause of the most severe problems when dealing with construction works below the water table. This is why it is critical to monitor groundwater recharge, distribution, and discharge on a continuous basis. The conventional method of monitoring groundwater employs a network of sparsely distributed monitoring wells and it is laborious, expensive, and intrusive. The problem of sparse data and undersampling reduces the accuracy of sampled survey data giving rise to poor interpretation. This dissertation addresses this problem by investigating groundwater-deformation response in order to augment the conventional method. A blend of three research methods was employed, namely design science research, geological methods, and geophysical methods, to examine whether persistent scatterer interferometry, a remote sensing technique, might augment conventional groundwater monitoring. Observation data (including phase information for displacement deformation from permanent scatterer interferometric synthetic aperture radar and depth to groundwater data) was obtained from the Water District, Santa Clara Valley, California. An information framework model was built and applied, and then evaluated. Data was preprocessed and decomposed into five components or parts: trend, seasonality, low frequency, high frequency and octave bandwidth. Digital elevation models of observed and predicted hydraulic head were produced, illustrating the piezometric or potentiometric surface. The potentiometric surface characterizes the regional aquifer of the valley showing areal variation of rate of percolation, velocity and permeability, and completely defines flow direction, advising characteristics and design levels. The findings show a geologic forcing phenomenon which explains in part the long-term deformation behavior of the valley, characterized by poroelastic, viscoelastic, elastoplastic and inelastic deformations under the influence of an underlying geologic southward plate motion within the theory of plate tectonics. It also explains the impact of a history of heavy pumpage of groundwater during the agricultural and urbanization era. Thus the persistent scatterer interferometry method offers an attractive, non-intrusive, cost-effective augmentation of the conventional method of monitoring groundwater for water resource development and stability of soil mass.

Assessment of two-phase flow on the chemical alteration and sealing of leakage pathways in cemented wellbores

DOE PAGES

Iyer, Jaisree; Walsh, Stuart D. C.; Hao, Yue; ...

2018-01-08

Wellbore leakage tops the list of perceived risks to the long-term geologic storage of CO 2, because wells provide a direct path between the CO 2 storage reservoir and the atmosphere. In this paper, we have coupled a two-phase flow model with our original framework that combined models for reactive transport of carbonated brine, geochemistry of reacting cement, and geomechanics to predict the permeability evolution of cement fractures. Additionally, this makes the framework suitable for field conditions in geological storage sites, permitting simulation of contact between cement and mixtures of brine and supercritical CO 2. Due to lack of conclusivemore » experimental data, we tried both linear and Corey relative permeability models to simulate flow of the two phases in cement fractures. The model also includes two options to account for the inconsistent experimental observations regarding cement reactivity with two-phase CO 2-brine mixtures. One option assumes that the reactive surface area is independent of the brine saturation and the second option assumes that the reactive surface area is proportional to the brine saturation. We have applied the model to predict the extent of cement alteration, the conditions under which fractures seal, the time it takes to seal a fracture, and the leakage rates of CO 2 and brine when damage zones in the wellbore are exposed to two-phase CO 2-brine mixtures. Initial brine residence time and the initial fracture aperture are critical parameters that affect the fracture sealing behavior. We also evaluated the importance of the model assumptions regarding relative permeability and cement reactivity. These results illustrate the need to understand how mixtures of carbon dioxide and brine flow through fractures and react with cement to make reasonable predictions regarding well integrity. For example, a reduction in the cement reactivity with two-phase CO 2-brine mixture can not only significantly increase the sealing time for fractures but may also prevent fracture sealing.« less

Assessment of two-phase flow on the chemical alteration and sealing of leakage pathways in cemented wellbores

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iyer, Jaisree; Walsh, Stuart D. C.; Hao, Yue

Wellbore leakage tops the list of perceived risks to the long-term geologic storage of CO 2, because wells provide a direct path between the CO 2 storage reservoir and the atmosphere. In this paper, we have coupled a two-phase flow model with our original framework that combined models for reactive transport of carbonated brine, geochemistry of reacting cement, and geomechanics to predict the permeability evolution of cement fractures. Additionally, this makes the framework suitable for field conditions in geological storage sites, permitting simulation of contact between cement and mixtures of brine and supercritical CO 2. Due to lack of conclusivemore » experimental data, we tried both linear and Corey relative permeability models to simulate flow of the two phases in cement fractures. The model also includes two options to account for the inconsistent experimental observations regarding cement reactivity with two-phase CO 2-brine mixtures. One option assumes that the reactive surface area is independent of the brine saturation and the second option assumes that the reactive surface area is proportional to the brine saturation. We have applied the model to predict the extent of cement alteration, the conditions under which fractures seal, the time it takes to seal a fracture, and the leakage rates of CO 2 and brine when damage zones in the wellbore are exposed to two-phase CO 2-brine mixtures. Initial brine residence time and the initial fracture aperture are critical parameters that affect the fracture sealing behavior. We also evaluated the importance of the model assumptions regarding relative permeability and cement reactivity. These results illustrate the need to understand how mixtures of carbon dioxide and brine flow through fractures and react with cement to make reasonable predictions regarding well integrity. For example, a reduction in the cement reactivity with two-phase CO 2-brine mixture can not only significantly increase the sealing time for fractures but may also prevent fracture sealing.« less

A Late Cenozoic Kinematic Model for Deformation Within the Greater Cascadia Subduction System

NASA Astrophysics Data System (ADS)

Wilson, D. S.; McCrory, P. A.

2016-12-01

Relatively low fault slip rates have complicated efforts to characterize seismic hazards associated with the diffuse subduction boundary between North America and offshore oceanic plates in the Pacific Northwest region. A kinematic forward model that encompasses a broader region, and incorporates seismologic and geodetic as well as geologic and paleomagnetic constraints offers a tool for constraining fault rupture chronologies—all within a framework tracking relative motion of the Juan de Fuca, Pacific, and North American plates during late Cenozoic time. Our kinematic model tracks motions as a system of rigid microplates, bounded by the more important mapped faults of the region or zones of distributed deformation. Though our emphasis is on Washington and Oregon, the scope of the model extends eastward to the rigid craton in Montana and Wyoming, and southward to the Sierra Nevada block of California to provide important checks on its internal consistency. The model reproduces observed geodetic velocities [e.g., McCaffrey et al., 2013, JGR], for 6 Ma to present, with only minor reorganization for 12-6 Ma. Constraints for the older deformation history are based on paleomagnetic rotations within the Columbia River Basalt Group, and geologic details of fault offsets. Since 17 Ma, our model includes 50 km of N-S shortening across the central Yakima fold and thrust belt, substantial NW-SE right-lateral strike slip distributed among faults in the Washington Cascade Range, 90 km of shortening on thrusts of Puget Lowland, and substantial oroclinal bending of the Crescent Formation basement surrounding the Olympic Peninsula. This kinematic reconstruction provides an integrated, quantitative framework with which to investigate the motions of various PNW forearc and backarc blocks during late Cenozoic time, an essential tool for characterizing the seismic risk associated with the Puget Sound and Portland urban areas, hydroelectric dams, and other critical infrastructure.

Design and Implementation Aspects of the Geological Data Infrastructure for European Society

NASA Astrophysics Data System (ADS)

van der Krogt, Rob; Pedersen, Mikael; Tulstrup, Jørgen; Robida, François; Serrrano, Jean-Jacques; Grellet, Sylvain; Lee, Kathryn; Harrison, Matthew; Demicheli, Luca; Delfini, Claudia; Hugelier, Sara; van Daalen, Tirza

2014-05-01

Digital geological data play a vital role in responding to the key social and economic challenges facing the European and global communities in the 21st century. These challenges include sustainable supply of energy, water and mineral resources, mitigating the impacts of natural hazards, and responding to climate change by exploiting renewable energy sources and capturing and storing greenhouse gases. As a response to these challenges the European geological surveys have enhanced their collaboration to prepare the implementation of a European Geological Data Infrastructure (EGDI), in order to provide easily accessible, interoperable and harmonized geological information on a European and international level. The high-level objective is to create a proper information base that supports the provision of geological services for European and international organisations, international industry and any other stakeholder working at cross-border or international level. It is additionally expected that the easy access to geological data at European level will enhance the development of new applications. The datasets to be served by the EGDI will primarily originate from the National Geological Survey Organisations (NGSO's) in Europe and the infrastructure will build further on the results of past, present and future European research projects and international programs in which these surveys are involved, for example the OneGeology-Europe project that serves regularly updated geological maps at 1:1M scale for the European area via a web portal. To prepare the implementation of the EGDI the NGSO's collaborate under the framework of the EU-FP7 EGDI-Scope study. This paper will present the main results and conclusions of this program, covering the following main issues that are taken into account to achieve the objectives of the EGDI: Stakeholder involvement: The study has exchanged with representative stakeholders from organisations and institutions to cover perspectives from policy, academia and industry. These exchanges have contributed to the description of relevant use cases. Prioritization of relevant datasets: Connected to relevant use cases, and the availability of datasets through the European survey organizations, from European projects and INSPIRE, a number of datasets (including associated derived information, tools and services) has been prioritized for the implementation phase. Technical design: Based on user requirements as well as specific technical requirements principles and preferred options for the technical design of the infrastructure have been described. Legal aspects: based on inventories and analyses of national and international legal frameworks, and connected to the objectives and requirements of the EGDI conclusions have been drawn with regard to the applicability of certain legal frameworks. Governance and funding aspects: A strategy and roadmap have been developed for appropriate governance structures for the several development stages of the EGDI, including cost estimates and options for funding from diverse programs at national and international levels.

Geologic framework for the national assessment of carbon dioxide storage resources: Hanna, Laramie, and Shirley Basins, Wyoming: Chapter C in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Merrill, Matthew D.; Covault, Jacob A.; Craddock, William H.; Slucher, Ernie R.; Warwick, Peter D.; Blondes, Madalyn S.; Gosai, Mayur A.; Freeman, P.A.; Cahan, Steven M.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2012-01-01

The 2007 Energy Independence and Security Act (Public Law 110-140) directs the U.S. Geological Survey (USGS) to conduct a national assessment of potential geologic storage resources for carbon dioxide (CO2). The methodology used for the national CO2 assessment is non-economic and intended to be used at regional to subbasinal scales. This report identifies and contains geologic descriptions of twelve storage assessment units (SAUs) in six separate packages of sedimentary rock within the Hanna, Laramie, and Shirley Basins of Wyoming. It focuses on the particular characteristics, specified in the methodology, that influence the potential CO2 storage resource in those SAUs. Specific descriptions of SAU boundaries as well as their sealing and reservoir units are included. Properties for each SAU, such as depth to top, gross thickness, net porous thickness, porosity, permeability, groundwater quality, and structural reservoir traps are provided to illustrate geologic factors critical to the assessment. Although assessment results are not contained in this report, the geologic information included herein will be employed, as specified in the methodology, to calculate a statistical Monte Carlo-based distribution of potential storage space in the various SAUs. Figures in this report show SAU boundaries and cell maps of well penetrations through the sealing unit into the top of the storage formation. Cell maps show the number of penetrating wells within one square mile and are derived from interpretations of incompletely attributed well data in a digital compilation that is known not to include all drilling. The USGS does not expect to know the location of all wells and cannot guarantee the amount of drilling through specific formations in any given cell shown on cell maps.

Mineralogic Model (MM3.0) Analysis Model Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

C. Lum

2002-02-12

The purpose of this report is to document the Mineralogic Model (MM), Version 3.0 (MM3.0) with regard to data input, modeling methods, assumptions, uncertainties, limitations and validation of the model results, qualification status of the model, and the differences between Version 3.0 and previous versions. A three-dimensional (3-D) Mineralogic Model was developed for Yucca Mountain to support the analyses of hydrologic properties, radionuclide transport, mineral health hazards, repository performance, and repository design. Version 3.0 of the MM was developed from mineralogic data obtained from borehole samples. It consists of matrix mineral abundances as a function of x (easting), y (northing),more » and z (elevation), referenced to the stratigraphic framework defined in Version 3.1 of the Geologic Framework Model (GFM). The MM was developed specifically for incorporation into the 3-D Integrated Site Model (ISM). The MM enables project personnel to obtain calculated mineral abundances at any position, within any region, or within any stratigraphic unit in the model area. The significance of the MM for key aspects of site characterization and performance assessment is explained in the following subsections. This work was conducted in accordance with the Development Plan for the MM (CRWMS M&O 2000). The planning document for this Rev. 00, ICN 02 of this AMR is Technical Work Plan, TWP-NBS-GS-000003, Technical Work Plan for the Integrated Site Model, Process Model Report, Revision 01 (CRWMS M&O 2000). The purpose of this ICN is to record changes in the classification of input status by the resolution of the use of TBV software and data in this report. Constraints and limitations of the MM are discussed in the appropriate sections that follow. The MM is one component of the ISM, which has been developed to provide a consistent volumetric portrayal of the rock layers, rock properties, and mineralogy of the Yucca Mountain site. The ISM consists of three components: (1) Geologic Framework Model (GFM); (2) Rock Properties Model (RPM); and (3) Mineralogic Model (MM). The ISM merges the detailed stratigraphy and structural features of the site into a 3-D model that will be useful in primary downstream models and repository design. These downstream models include the hydrologic flow models and the radionuclide transport models. All the models and the repository design, in turn, will be incorporated into the Total System Performance Assessment (TSPA) of the potential nuclear waste repository block and vicinity to determine the suitability of Yucca Mountain as a host for a repository. The interrelationship of the three components of the ISM and their interface with downstream uses are illustrated in Figure 1. The lateral boundaries of the ISM and its three component models are shown in Figure 2.« less

The value of DCIP geophysical surveys for contaminated site investigations

NASA Astrophysics Data System (ADS)

Balbarini, N.; Rønde, V.; Maurya, P. K.; Møller, I.; McKnight, U. S.; Christiansen, A. V.; Binning, P. J.; Bjerg, P. L.

2017-12-01

Geophysical methods are increasingly being used in contaminant hydrogeology to map lithology, hydraulic properties, and contaminant plumes with a high ionic strength. Advances in the Direct Current resistivity and Induced Polarization (DCIP) method allow the collection of high resolution three dimensional (3D) data sets. The DC resistivity can describe both soil properties and the water electrical conductivity, while the IP can describe the lithology and give information on hydrogeological properties. The aim of the study was to investigate a large contaminant plume discharging to a stream from an old factory site by combining traditional geological, hydrological, and contaminant concentration data with DCIP surveys. The plume consisted of xenobiotic organic compounds and inorganics. The study assesses benefits and limitations of DCIP geophysics for contaminated site investigations. A 3D geological model was developed from borehole logs and DCIP data as framework for the complex transport pathways near the meandering stream. IP data were useful in indicating the continuity and the changes in thickness of local clay layers between the borehole logs. The geological model was employed to develop a groundwater flow model describing groundwater flows to the stream. The hydraulic conductivity distribution was based on IP data, slug tests and grain size analysis. The distribution of contaminant concentrations revealed two chemically distinct plumes, separated by a clay layer, with different transport paths to the stream. The DC resistivity was useful in mapping ionic compounds, but also organic compounds whose spatial distribution coincided with the ionic compounds. A conceptual model describing the contaminant plume was developed, and it matched well with contaminant concentrations in stream water and below the streambed. Surface DCIP surveys supported the characterization of the spatial variability in geology, hydraulic conductivity and contaminant concentration. Though DCIP data interpretation required additional borehole data, the DCIP survey reduced the number of boreholes required and helped design field campaigns. The results suggest DCIP surveys are useful and inexpensive tools, which has potential as an integrated part of contaminated site investigations.

National Assessment of Oil and Gas Project: Petroleum Systems and Geologic Assessment of Undiscovered Oil and Gas, Hanna, Laramie, and Shirley Basins Province, Wyoming

USGS Publications Warehouse

U.S. Geological Survey Hanna, Laramie

2007-01-01

INTRODUCTION The purpose of the U.S. Geological Survey?s (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The U.S. Geological Survey (USGS) recently completed an assessment of the undiscovered oil and gas potential of the Hanna, Laramie, and Shirley Basins Province in Wyoming and northeastern Colorado. The assessment is based on the geologic elements of each total petroleum system (TPS) defined in the province, including hydrocarbon source rocks (source-rock maturation, hydrocarbon generation, and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined three TPSs and seven assessment units (AUs) within them; undiscovered resources for three of the seven AUs were quantitatively assessed.

Jurassic-Cretaceous Composite Total Petroleum System and Geologic Assessment of Oil and Gas Resources of the North Cuba Basin, Cuba

USGS Publications Warehouse

,

2008-01-01

The purpose of the U.S. Geological Survey's (USGS) World Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the world. The U.S. Geological Survey (USGS) completed an assessment of the undiscovered oil and gas potential of the North Cuba Basin. The assessment is based on the geologic elements of the total petroleum system (TPS) defined in the province, including petroleum source rocks (source-rock maturation, generation, and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and petroleum traps (Trap formation and timing). Using this geologic framework, the USGS defined a Jurassic-Cretaceous Total Petroleum System in the North Cuba Basin Province. Within this TPS, three assessment units were defined and assessed for undiscovered oil and gas resources.

Laws, Place, History and the Interpretation of Earth Surface Systems

NASA Astrophysics Data System (ADS)

Phillips, Jonathan

2016-04-01

The state of an Earth surface system (ESS is determined by three sets of factors: Laws, place, and history. Laws (L = L1, L2, . . . , Ln) are the n general principles, relationships, and representations applicable to any such system at any time. Place factors (P = P1, P2, . . . , Pm) are the m relevant properties or characteristics of the local or regional environment - e.g., climate, tectonic setting, geology, traits of the local biota, etc. History factors (H = H1 , H2, . . . , Hq) include the previous evolutionary pathway of the ESS, its stage of development, past disturbance, and in some contexts initial conditions. Geoscience investigation may be focused on laws (e.g., theoretical deductions, process modeling, laboratory experiments), place (e.g., regional geology or geography, soil-landscape studies), or history (e.g., paleoenvironmental studies, environmental history, historical geology or geography). Ultimately, however, all three sets of factors are necessary to fully understand and explain ESS. Beyond providing a useful checklist (analogous to the factorial models often used in pedology and ecology), the LPH framework gives us analytical traction to some difficult research problems. For example, studies of the avulsions of three southeast Texas rivers showed substantial differences in avulsion regimes and resulting alluvial morphology, despite the proximity and superficial similarity of the systems. Avulsion dynamics are governed by the same laws in all three cases [L(A) = L(B) = L(C)], and the three rivers, once part of a single system at lower sea-levels, have undergone the same sea-level, climate, and tectonic histories, as well as the same general types of anthropic impacts [H(A) ≈ H(B) ≈ H(C)]. Though the regional-scale environmental controls are similar, local details such as the location of the modern main channel relative to Pleistocene meander channels differ, and thus these place factors explain the differences between the rivers. The LPH framework can also be used to determine the source of similarities among disparate systems. A classic example is the topology of fluvial channel networks, which have similar characteristics despite a great variety in place and history factors. Since P(i) ≠ P(j), H(i) ≠ H(j), this points to L factors as the controls of the similarities. Similar trends are emerging in the study of root-rock interactions in forest regoliths, where similar phenomena occur despite variations in underlying geology, vegetation, and disturbance regimes. The LPH framework, or very similar types of reasoning, is implicit in many types of geoscience analysis. More explicit attention to the triad can help us solve or address many specific problems and remind us of the importance of all three sets of factors.

A Machine-Learning and Filtering Based Data Assimilation Framework for Geologic Carbon Sequestration Monitoring Optimization

NASA Astrophysics Data System (ADS)

Chen, B.; Harp, D. R.; Lin, Y.; Keating, E. H.; Pawar, R.

2017-12-01

Monitoring is a crucial aspect of geologic carbon sequestration (GCS) risk management. It has gained importance as a means to ensure CO2 is safely and permanently stored underground throughout the lifecycle of a GCS project. Three issues are often involved in a monitoring project: (i) where is the optimal location to place the monitoring well(s), (ii) what type of data (pressure, rate and/or CO2 concentration) should be measured, and (iii) What is the optimal frequency to collect the data. In order to address these important issues, a filtering-based data assimilation procedure is developed to perform the monitoring optimization. The optimal monitoring strategy is selected based on the uncertainty reduction of the objective of interest (e.g., cumulative CO2 leak) for all potential monitoring strategies. To reduce the computational cost of the filtering-based data assimilation process, two machine-learning algorithms: Support Vector Regression (SVR) and Multivariate Adaptive Regression Splines (MARS) are used to develop the computationally efficient reduced-order-models (ROMs) from full numerical simulations of CO2 and brine flow. The proposed framework for GCS monitoring optimization is demonstrated with two examples: a simple 3D synthetic case and a real field case named Rock Spring Uplift carbon storage site in Southwestern Wyoming.

Mind the Gaps: Expert and Non-Expert Differences in Conceptualising the Geological Subsurface.

NASA Astrophysics Data System (ADS)

Gibson, H.; Stewart, I. S.; Stokes, A.; Pahl, S.

2017-12-01

In communicating geoscience topics, emphasis is often given to approaches such as the use of narrative to make a message engaging and reducing the use of jargon to ensure that it is understood by as wide a group of people as possible. Whilst these are undeniably important techniques to promote effective communication, an aspect of geoscience communication that is often overlooked is the publics' conceptual frameworks about core geoscience concepts. The consideration of different conceptual frameworks fits with the need to ensure that the framing is appropriate for the message, but it extends beyond simple framing into more complicated issues of addressing and incorporating pre- and mis-conceptions in geoscience. In a study examining expert and non-expert cognitive (mental) models of the geological subsurface in south-west England, several gaps were found between the fundamental ways that experts and non-experts conceptualise this invisible realm. Of these, three gaps were considered to be particularly important and common to many participants: the use of spatial reasoning; the application of surface experiences to subsurface processes; and the connection between the surface and subsurface. This paper will examine the evidence for these three important conceptual gaps between specialists and non-specialists and will address how this type of cognitive study can help improve effective geoscience communication.

Shallow geology, sea-floor texture, and physiographic zones of Vineyard and western Nantucket Sounds, Massachusetts

USGS Publications Warehouse

Baldwin, Wayne E.; Foster, David S.; Pendleton, Elizabeth A.; Barnhardt, Walter A.; Schwab, William C.; Andrews, Brian D.; Ackerman, Seth D.

2016-09-02

Geologic, sediment texture, and physiographic zone maps characterize the sea floor of Vineyard and western Nantucket Sounds, Massachusetts. These maps were derived from interpretations of seismic-reflection profiles, high-resolution bathymetry, acoustic-backscatter intensity, bottom photographs/video, and surficial sediment samples collected within the 494-square-kilometer study area. Interpretations of seismic stratigraphy and mapping of glacial and Holocene marine units provided a foundation on which the surficial maps were created. This mapping is a result of a collaborative effort between the U.S. Geological Survey and the Massachusetts Office of Coastal Zone Management to characterize the surface and subsurface geologic framework offshore of Massachusetts.

Yucca Mountain, Nevada - A proposed geologic repository for high-level radioactive waste

USGS Publications Warehouse

Levich, R.A.; Stuckless, J.S.

2006-01-01

Yucca Mountain in Nevada represents the proposed solution to what has been a lengthy national effort to dispose of high-level radioactive waste, waste which must be isolated from the biosphere for tens of thousands of years. This chapter reviews the background of that national effort and includes some discussion of international work in order to provide a more complete framework for the problem of waste disposal. Other chapters provide the regional geologic setting, the geology of the Yucca Mountain site, the tectonics, and climate (past, present, and future). These last two chapters are integral to prediction of long-term waste isolation. ?? 2007 Geological Society of America. All rights reserved.

Mechanical constraints on fault geometries and structural styles in extensional geologic settings

NASA Astrophysics Data System (ADS)

Hughes, A. N.

2017-12-01

The geologic structures that accommodate crustal extension in various tectonic environments, including rifts basins, passive margins, and gravitational collapse systems, exhibit a wide range of geometric styles. While several previous studies have focused on the mechanical controls on crustal-scale rift margin geometry, less attention has been paid to the role of mechanics in the style of the individual structures or groups of structures that deform the brittle upper crust. The main modes of extensional structures that have been observed—including parallel fault arrays, half-grabens, grabens, and core complexes—inherently imply mechanical conditions that favor their formation, but an exhaustive evaluation of the circumstances that favor the creation of each of these primary types has yet to be explored, and thus is the focus of this study. This issue is addressed through the construction of a series of 2D forward mechanical models using the discrete element modeling approach. With the intent of representing the wide range of realistic geologic circumstances in which these structures form, a suite of models were constructed by varying parameters such as rock section thickness and strength properties, detachment zone friction, thickness, and dip, extension rate, and various boundary conditions such as erosion and syntectonic sedimentation. The results of these models were then evaluated in order to identify the combinations of parameters that favor the development of each of the main structural styles. Furthermore, the ability to interrogate the stress and strain fields in the models helps shed light on the specific mechanisms that give rise to these different manifestations of extensional strain. Application of these insights to interpretations of extensional structures in rift basins will help to provide a useful framework for understanding the connection between the observed structural style in a region and the conditions that gave rise to its occurrence.

Implicit Three-Dimensional Geo-Modelling Based on HRBF Surface

NASA Astrophysics Data System (ADS)

Gou, J.; Zhou, W.; Wu, L.

2016-10-01

Three-dimensional (3D) geological models are important representations of the results of regional geological surveys. However, the process of constructing 3D geological models from two-dimensional (2D) geological elements remains difficult and time-consuming. This paper proposes a method of migrating from 2D elements to 3D models. First, the geological interfaces were constructed using the Hermite Radial Basis Function (HRBF) to interpolate the boundaries and attitude data. Then, the subsurface geological bodies were extracted from the spatial map area using the Boolean method between the HRBF surface and the fundamental body. Finally, the top surfaces of the geological bodies were constructed by coupling the geological boundaries to digital elevation models. Based on this workflow, a prototype system was developed, and typical geological structures (e.g., folds, faults, and strata) were simulated. Geological modes were constructed through this workflow based on realistic regional geological survey data. For extended applications in 3D modelling of other kinds of geo-objects, mining ore body models and urban geotechnical engineering stratum models were constructed by this method from drill-hole data. The model construction process was rapid, and the resulting models accorded with the constraints of the original data.

QUANTITATIVE METHODS FOR RESERVOIR CHARACTERIZATION AND IMPROVED RECOVERY: APPLICATION TO HEAVY OIL SANDS

DOE Office of Scientific and Technical Information (OSTI.GOV)

James W. Castle; Fred J. Molz; Ronald W. Falta

2002-10-30

Improved prediction of interwell reservoir heterogeneity has the potential to increase productivity and to reduce recovery cost for California's heavy oil sands, which contain approximately 2.3 billion barrels of remaining reserves in the Temblor Formation and in other formations of the San Joaquin Valley. This investigation involves application of advanced analytical property-distribution methods conditioned to continuous outcrop control for improved reservoir characterization and simulation, particularly in heavy oil sands. The investigation was performed in collaboration with Chevron Production Company U.S.A. as an industrial partner, and incorporates data from the Temblor Formation in Chevron's West Coalinga Field. Observations of lateral variabilitymore » and vertical sequences observed in Temblor Formation outcrops has led to a better understanding of reservoir geology in West Coalinga Field. Based on the characteristics of stratigraphic bounding surfaces in the outcrops, these surfaces were identified in the subsurface using cores and logs. The bounding surfaces were mapped and then used as reference horizons in the reservoir modeling. Facies groups and facies tracts were recognized from outcrops and cores of the Temblor Formation and were applied to defining the stratigraphic framework and facies architecture for building 3D geological models. The following facies tracts were recognized: incised valley, estuarine, tide- to wave-dominated shoreline, diatomite, and subtidal. A new minipermeameter probe, which has important advantages over previous methods of measuring outcrop permeability, was developed during this project. The device, which measures permeability at the distal end of a small drillhole, avoids surface weathering effects and provides a superior seal compared with previous methods for measuring outcrop permeability. The new probe was used successfully for obtaining a high-quality permeability data set from an outcrop in southern Utah. Results obtained from analyzing the fractal structure of permeability data collected from the southern Utah outcrop and from core permeability data provided by Chevron from West Coalinga Field were used in distributing permeability values in 3D reservoir models. Spectral analyses and the Double Trace Moment method (Lavallee et al., 1991) were used to analyze the scaling and multifractality of permeability data from cores from West Coalinga Field. T2VOC, which is a numerical flow simulator capable of modeling multiphase, multi-component, nonisothermal flow, was used to model steam injection and oil production for a portion of section 36D in West Coalinga Field. The layer structure and permeability distributions of different models, including facies group, facies tract, and fractal permeability models, were incorporated into the numerical flow simulator. The injection and production histories of wells in the study area were modeled, including shutdowns and the occasional conversion of production wells to steam injection wells. The framework provided by facies groups provides a more realistic representation of the reservoir conditions than facies tracts, which is revealed by a comparison of the history-matching for the oil production. Permeability distributions obtained using the fractal results predict the high degree of heterogeneity within the reservoir sands of West Coalinga Field. The modeling results indicate that predictions of oil production are strongly influenced by the geologic framework and by the boundary conditions. The permeability data collected from the southern Utah outcrop, support a new concept for representing natural heterogeneity, which is called the fractal/facies concept. This hypothesis is one of the few potentially simplifying concepts to emerge from recent studies of geological heterogeneity. Further investigation of this concept should be done to more fully apply fractal analysis to reservoir modeling and simulation. Additional outcrop permeability data sets and further analysis of the data from distinct facies will be needed in order to fully develop this new concept.« less

Archive of digital Chirp subbottom profile data collected during USGS cruise 08CCT01, Mississippi Gulf Islands, July 2008

USGS Publications Warehouse

Forde, Arnell S.; Dadisman, Shawn V.; Flocks, James G.; Worley, Charles R.

2011-01-01

In July of 2008, the U.S. Geological Survey (USGS) conducted geophysical surveys to investigate the geologic controls on island framework from Ship Island to Horn Island, Mississippi, for the Northern Gulf of Mexico (NGOM) Ecosystem Change and Hazard Susceptibility project. Funding was provided through the Geologic Framework and Holocene Coastal Evolution of the Mississippi-Alabama Region Subtask (http://ngom.er.usgs.gov/task2_2/index.php); this project is also part of a broader USGS study on Coastal Change and Transport (CCT). This report serves as an archive of unprocessed digital Chirp seismic reflection data, trackline maps, navigation files, Geographic Information System (GIS) files, Field Activity Collection System (FACS) logs, observer's logbook, and formal Federal Geographic Data Committee (FGDC) metadata. Gained (a relative increase in signal amplitude) digital images of the seismic profiles are also provided. Refer to the Acronyms page for expansion of acronyms and abbreviations used in this report.

Lithofacies and sequence stratigraphic description of the upper part of the Avon Park Formation and the Arcadia Formation in U.S. Geological Survey G–2984 test corehole, Broward County, Florida

USGS Publications Warehouse

Cunningham, Kevin J.; Robinson, Edward

2017-07-18

Rock core and sediment from U.S. Geological Survey test corehole G–2984 completed in 2011 in Broward County, Florida, provide an opportunity to improve the understanding of the lithostratigraphic, sequence stratigraphic, and hydrogeologic framework of the intermediate confining unit and Floridan aquifer system in southeastern Florida. A multidisciplinary approach including characterization of sequence stratigraphy, lithofacies, ichnology, foraminiferal paleontology, depositional environments, porosity, and permeability was used to describe the geologic samples from this test corehole. This information has produced a detailed characterization of the lithofacies and sequence stratigraphy of the upper part of the middle Eocene Avon Park Formation and Oligocene to middle Miocene Arcadia Formation. This enhancement of the knowledge of the sequence stratigraphic framework is especially important, because subaerial karst unconformities at the upper boundary of depositional cycles at various hierarchical scales are commonly associated with secondary porosity and enhanced permeability in the Floridan aquifer system.

Audiomagnetotelluric Data and Two-Dimensional Models from Spring, Snake, and Three Lakes Valleys, Nevada

USGS Publications Warehouse

McPhee, Darcy K.; Chuchel, Bruce A.; Pellerin, Louise

2007-01-01

Audiomagnetotelluric (AMT) data along thirteen profiles in Spring, Snake, and Three Lakes Valleys, and the corresponding two-dimensional (2-D) inverse models, are presented. The AMT method is a valuable tool for estimating the electrical resistivity of the Earth over depth ranges of a few meters to roughly one kilometer. It is important for revealing subsurface structure and stratigraphy within the Basin and Range province of eastern Nevada that can be used to define the geohydrologic framework of the region. We collected AMT data using the Geometrics StrataGem EH4 system. Profiles were 1.2 to 4.6 km in length with station spacing of 100-400 m. Data were recorded in a coordinate system parallel to and perpendicular to the assumed regional geologic strike direction. We show station locations, sounding curves of apparent resistivity, phase, and coherency, and 2-D models. The 2-D inverse models are computed from the transverse electric (TE), transverse magnetic (TM), and TE+TM mode data using the conjugate gradient, finite-difference method of Rodi and Mackie (2001). Preliminary interpretation of these models defines the structural framework of the basins and the resistivity contrasts between alluvial basin-fill, volcanic units, and carbonate/clastic rocks.

An Evaluation Tool for CONUS-Scale Estimates of Components of the Water Balance

NASA Astrophysics Data System (ADS)

Saxe, S.; Hay, L.; Farmer, W. H.; Markstrom, S. L.; Kiang, J. E.

2016-12-01

Numerous research groups are independently developing data products to represent various components of the water balance (e.g. runoff, evapotranspiration, recharge, snow water equivalent, soil moisture, and climate) at the scale of the conterminous United States. These data products are derived from a range of sources, including direct measurement, remotely-sensed measurement, and statistical and deterministic model simulations. An evaluation tool is needed to compare these data products and the components of the water balance they contain in order to identify the gaps in the understanding and representation of continental-scale hydrologic processes. An ideal tool will be an objective, universally agreed upon, framework to address questions related to closing the water balance. This type of generic, model agnostic evaluation tool would facilitate collaboration amongst different hydrologic research groups and improve modeling capabilities with respect to continental-scale water resources. By adopting a comprehensive framework to consider hydrologic modeling in the context of a complete water balance, it is possible to identify weaknesses in process modeling, data product representation and regional hydrologic variation. As part of its National Water Census initiative, the U.S. Geological survey is facilitating this dialogue to developing prototype evaluation tools.

National Assessment of Oil and Gas Project: Geologic Assessment of Undiscovered Oil and Gas Resources of the Eastern Great Basin Province, Nevada, Utah, Idaho, and Arizona

USGS Publications Warehouse

,

2007-01-01

Introduction The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The U.S. Geological Survey (USGS) recently completed an assessment of the undiscovered oil and gas potential of the Eastern Great Basin Province of eastern Nevada, western Utah, southeastern Idaho, and northwestern Arizona. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define one total petroleum system and three assessment units. All three assessment units were quantitatively assessed for undiscovered oil and gas resources.

Cratering on Mars. I - Cratering and obliteration history. II Implications for future cratering studies from Mariner 4 reanalysis

NASA Technical Reports Server (NTRS)

Chapman, C. R.

1974-01-01

It is pointed out that Mars is especially well adapted to statistical studies of crater morphologies for deciphering its geological history. A framework for understanding planetary geomorphological histories from the diameter-frequency relations of different morphological classes of craters described by Chapmam et al. (1970) is extended in order to understand Martian cratering, erosional, and depositional history. The cratering-obliteration history derived is compared with global interpretations considered by Hartman (1973) and Soderblom et al. (1974). An idealized dust-filling model is employed.

Revised Subsurface Stratigraphic Framework of the Fort Union and Wasatch Formations, Powder River Basin, Wyoming and Montana

USGS Publications Warehouse

Flores, Romeo M.; Spear, Brianne D.; Purchase, Peter A.; Gallagher, Craig M.

2010-01-01

Described in this report is an updated subsurface stratigraphic framework of the Paleocene Fort Union Formation and Eocene Wasatch Formation in the Powder River Basin (PRB) in Wyoming and Montana. This framework is graphically presented in 17 intersecting west-east and north-south cross sections across the basin. Also included are: (1) the dataset and all associated digital files and (2) digital files for all figures and table 1 suitable for large-format printing. The purpose of this U.S. Geological Survey (USGS) Open-File Report is to provide rapid dissemination and accessibility of the stratigraphic cross sections and related digital data to USGS customers, especially the U.S. Bureau of Land Management (BLM), to facilitate their modeling of the hydrostratigraphy of the PRB. This report contains a brief summary of the coal-bed correlations and database, and is part of a larger ongoing study that will be available in the near future.

Astronomical calibration of the geological timescale: closing the middle Eocene gap

NASA Astrophysics Data System (ADS)

Westerhold, T.; Röhl, U.; Frederichs, T.; Bohaty, S. M.; Zachos, J. C.

2015-09-01

To explore cause and consequences of past climate change, very accurate age models such as those provided by the astronomical timescale (ATS) are needed. Beyond 40 million years the accuracy of the ATS critically depends on the correctness of orbital models and radioisotopic dating techniques. Discrepancies in the age dating of sedimentary successions and the lack of suitable records spanning the middle Eocene have prevented development of a continuous astronomically calibrated geological timescale for the entire Cenozoic Era. We now solve this problem by constructing an independent astrochronological stratigraphy based on Earth's stable 405 kyr eccentricity cycle between 41 and 48 million years ago (Ma) with new data from deep-sea sedimentary sequences in the South Atlantic Ocean. This new link completes the Paleogene astronomical timescale and confirms the intercalibration of radioisotopic and astronomical dating methods back through the Paleocene-Eocene Thermal Maximum (PETM, 55.930 Ma) and the Cretaceous-Paleogene boundary (66.022 Ma). Coupling of the Paleogene 405 kyr cyclostratigraphic frameworks across the middle Eocene further paves the way for extending the ATS into the Mesozoic.

The role of 3D visualisation as an analytical tool preparatory to numerical modelling [rapid communication

NASA Astrophysics Data System (ADS)

Robins, N. S.; Rutter, H. K.; Dumpleton, S.; Peach, D. W.

2005-01-01

Groundwater investigation has long depended on the process of developing a conceptual flow model as a precursor to developing a mathematical model, which in turn may lead in complex aquifers to the development of a numerical approximation model. The assumptions made in the development of the conceptual model depend heavily on the geological framework defining the aquifer, and if the conceptual model is inappropriate then subsequent modelling will also be incorrect. Paradoxically, the development of a robust conceptual model remains difficult, not least because this 3D paradigm is usually reduced to 2D plans and sections. 3D visualisation software is now available to facilitate the development of the conceptual model, to make the model more robust and defensible and to assist in demonstrating the hydraulics of the aquifer system. Case studies are presented to demonstrate the role and cost-effectiveness of the visualisation process.

Geologic framework for the national assessment of carbon dioxide storage resources: Greater Green River Basin, Wyoming, Colorado, and Utah, and Wyoming-Idaho-Utah Thrust Belt: Chapter E in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Buursink, Marc L.; Slucher, Ernie R.; Brennan, Sean T.; Doolan, Colin A.; Drake II, Ronald M.; Merrill, Matthew D.; Warwick, Peter D.; Blondes, Madalyn S.; Freeman, P.A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.

2014-01-01

The 2007 Energy Independence and Security Act (Public Law 110–140) directs the U.S. Geological Survey (USGS) to conduct a national assessment of potential geologic storage resources for carbon dioxide (CO2). The methodology used by the USGS for the national CO2 assessment follows up on previous USGS work. The methodology is non-economic and intended to be used at regional to subbasinal scales. This report identifies and contains geologic descriptions of 14 storage assessment units (SAUs) in Ordovician to Upper Cretaceous sedimentary rocks within the Greater Green River Basin (GGRB) of Wyoming, Colorado, and Utah, and eight SAUs in Ordovician to Upper Cretaceous sedimentary rocks within the Wyoming-Idaho-Utah Thrust Belt (WIUTB). The GGRB and WIUTB are contiguous with nearly identical geologic units; however, the GGRB is larger in size, whereas the WIUTB is more structurally complex. This report focuses on the characteristics, specified in the methodology, that influence the potential CO2 storage resource in the SAUs. Specific descriptions of the SAU boundaries, as well as their sealing and reservoir units, are included. Properties for each SAU, such as depth to top, gross thickness, porosity, permeability, groundwater quality, and structural reservoir traps, are typically provided to illustrate geologic factors critical to the assessment. This geologic information was employed, as specified in the USGS methodology, to calculate a probabilistic distribution of potential storage resources in each SAU. Figures in this report show SAU boundaries and cell maps of well penetrations through sealing units into the top of the storage formations. The cell maps show the number of penetrating wells within one square mile and are derived from interpretations of variably attributed well data and a digital compilation that is known not to include all drilling.

Study on Potential Changes in Geological and Disposal Environment Caused by 'Natural Phenomena' on a HLW Disposal System

NASA Astrophysics Data System (ADS)

Kawamura, M.; Umeda, K.; Ohi, T.; Ishimaru, T.; Niizato, T.; Yasue, K.; Makino, H.

2007-12-01

We have developed a formal evaluation method to assess the potential impact of natural phenomena (earthquakes and faulting; volcanism; uplift, subsidence, denudation and sedimentation; climatic and sea-level changes) on a High Level Radioactive Waste (HLW) Disposal System. In 2000, we had developed perturbation scenarios in a generic and conservative sense and illustrated the potential impact on a HLW disposal system. As results of the development of perturbation scenarios, two points were highlighted for consideration in subsequent work: improvement of the scenarios from the viewpoints of reality, transparency, traceability and consistency and avoiding extreme conservatism. Subsequently, we have thus developed a new procedure for describing such perturbation scenarios based on further studies of the characteristics of these natural perturbation phenomena in Japan. The approach to describing the perturbation scenario is effectively developed in five steps: Step 1: Description of potential process of phenomena and their impacts on the geological environment. Step 2: Characterization of potential changes of geological environment in terms of T-H-M-C (Thermal - Hydrological - Mechanical - Chemical) processes. The focus is on specific T-H-M-C parameters that influence geological barrier performance, utilizing the input from Step 1. Step 3: Classification of potential influences, based on similarity of T-H-M-C perturbations. This leads to development of perturbation scenarios to serve as a basis for consequence analysis. Step 4: Establishing models and parameters for performance assessment. Step 5: Calculation and assessment. This study focuses on identifying key T-H-M-C process associated with perturbations at Step 2. This framework has two advantages. First one is assuring maintenance of traceability during the scenario construction processes, facilitating the production and structuring of suitable records. The second is providing effective elicitation and organization of information from a wide range of investigations of earth sciences within a performance assessment context. In this framework, scenario development work proceeds in a stepwise manner, to ensure clear identification of the impact of processes associated with these phenomena on a HLW disposal system. Output is organized to create credible scenarios with required transparency, consistency, traceability and adequate conservatism. In this presentation, the potential impact of natural phenomena in the viewpoint of performance assessment for HLW disposal will be discussed and modeled using the approach.

Hydrologic and geologic characteristics of the Yucca Mountain site relevant to the performance of a potential repository

USGS Publications Warehouse

Levich, R.A.; Linden, R.M.; Patterson, R.L.; Stuckless, J.S.

2000-01-01

Yucca Mountain, located ~100 mi northwest of Las Vegas, Nevada, has been designated by Congress as a site to be characterized for a potential mined geologic repository for high-level radioactive waste. This field trip will examine the regional geologic and hydrologic setting for Yucca Mountain, as well as specific results of the site characterization program. The first day focuses on the regional setting with emphasis on current and paleo hydrology, which are both of critical concern for predicting future performance of a potential repository. Morning stops will be southern Nevada and afternoon stops will be in Death Valley. The second day will be spent at Yucca Mountain. The field trip will visit the underground testing sites in the "Exploratory Studies Facility" and the "Busted Butte Unsaturated Zone Transport Field Test" plus several surface-based testing sites. Much of the work at the site has concentrated on studies of the unsaturated zone, an element of the hydrologic system that historically has received little attention. Discussions during the second day will compromise selected topics of Yucca Mountain geology, hydrology and geochemistry and will include the probabilistic volcanic hazard analysis and the seismicity and seismic hazard in the Yucca Mountain area. Evening discussions will address modeling of regional groundwater flow, the results of recent hydrologic studies by the Nye County Nuclear Waste Program Office, and the relationship of the geology and hydrology of Yucca Mountain to the performance of a potential repository. Day 3 will examine the geologic framework and hydrology of the Pahute Mesa-Oasis Valley Groundwater Basin and then will continue to Reno via Hawthorne, Nevada and the Walker Lake area.

Bayesian phylogenetic estimation of fossil ages.

PubMed

Drummond, Alexei J; Stadler, Tanja

2016-07-19

Recent advances have allowed for both morphological fossil evidence and molecular sequences to be integrated into a single combined inference of divergence dates under the rule of Bayesian probability. In particular, the fossilized birth-death tree prior and the Lewis-Mk model of discrete morphological evolution allow for the estimation of both divergence times and phylogenetic relationships between fossil and extant taxa. We exploit this statistical framework to investigate the internal consistency of these models by producing phylogenetic estimates of the age of each fossil in turn, within two rich and well-characterized datasets of fossil and extant species (penguins and canids). We find that the estimation accuracy of fossil ages is generally high with credible intervals seldom excluding the true age and median relative error in the two datasets of 5.7% and 13.2%, respectively. The median relative standard error (RSD) was 9.2% and 7.2%, respectively, suggesting good precision, although with some outliers. In fact, in the two datasets we analyse, the phylogenetic estimate of fossil age is on average less than 2 Myr from the mid-point age of the geological strata from which it was excavated. The high level of internal consistency found in our analyses suggests that the Bayesian statistical model employed is an adequate fit for both the geological and morphological data, and provides evidence from real data that the framework used can accurately model the evolution of discrete morphological traits coded from fossil and extant taxa. We anticipate that this approach will have diverse applications beyond divergence time dating, including dating fossils that are temporally unconstrained, testing of the 'morphological clock', and for uncovering potential model misspecification and/or data errors when controversial phylogenetic hypotheses are obtained based on combined divergence dating analyses.This article is part of the themed issue 'Dating species divergences using rocks and clocks'. © 2016 The Authors.

Bayesian phylogenetic estimation of fossil ages

PubMed Central

Drummond, Alexei J.; Stadler, Tanja

2016-01-01

Recent advances have allowed for both morphological fossil evidence and molecular sequences to be integrated into a single combined inference of divergence dates under the rule of Bayesian probability. In particular, the fossilized birth–death tree prior and the Lewis-Mk model of discrete morphological evolution allow for the estimation of both divergence times and phylogenetic relationships between fossil and extant taxa. We exploit this statistical framework to investigate the internal consistency of these models by producing phylogenetic estimates of the age of each fossil in turn, within two rich and well-characterized datasets of fossil and extant species (penguins and canids). We find that the estimation accuracy of fossil ages is generally high with credible intervals seldom excluding the true age and median relative error in the two datasets of 5.7% and 13.2%, respectively. The median relative standard error (RSD) was 9.2% and 7.2%, respectively, suggesting good precision, although with some outliers. In fact, in the two datasets we analyse, the phylogenetic estimate of fossil age is on average less than 2 Myr from the mid-point age of the geological strata from which it was excavated. The high level of internal consistency found in our analyses suggests that the Bayesian statistical model employed is an adequate fit for both the geological and morphological data, and provides evidence from real data that the framework used can accurately model the evolution of discrete morphological traits coded from fossil and extant taxa. We anticipate that this approach will have diverse applications beyond divergence time dating, including dating fossils that are temporally unconstrained, testing of the ‘morphological clock', and for uncovering potential model misspecification and/or data errors when controversial phylogenetic hypotheses are obtained based on combined divergence dating analyses. This article is part of the themed issue ‘Dating species divergences using rocks and clocks’. PMID:27325827

Contribution of physical modelling to climate-driven landslide hazard mapping: an alpine test site

NASA Astrophysics Data System (ADS)

Vandromme, R.; Desramaut, N.; Baills, A.; Hohmann, A.; Grandjean, G.; Sedan, O.; Mallet, J. P.

2012-04-01

The aim of this work is to develop a methodology for integrating climate change scenarios into quantitative hazard assessment and especially their precipitation component. The effects of climate change will be different depending on both the location of the site and the type of landslide considered. Indeed, mass movements can be triggered by different factors. This paper describes a methodology to address this issue and shows an application on an alpine test site. Mechanical approaches represent a solution for quantitative landslide susceptibility and hazard modeling. However, as the quantity and the quality of data are generally very heterogeneous at a regional scale, it is necessary to take into account the uncertainty in the analysis. In this perspective, a new hazard modeling method is developed and integrated in a program named ALICE. This program integrates mechanical stability analysis through a GIS software taking into account data uncertainty. This method proposes a quantitative classification of landslide hazard and offers a useful tool to gain time and efficiency in hazard mapping. However, an expertise approach is still necessary to finalize the maps. Indeed it is the only way to take into account some influent factors in slope stability such as heterogeneity of the geological formations or effects of anthropic interventions. To go further, the alpine test site (Barcelonnette area, France) is being used to integrate climate change scenarios into ALICE program, and especially their precipitation component with the help of a hydrological model (GARDENIA) and the regional climate model REMO (Jacob, 2001). From a DEM, land-cover map, geology, geotechnical data and so forth the program classifies hazard zones depending on geotechnics and different hydrological contexts varying in time. This communication, realized within the framework of Safeland project, is supported by the European Commission under the 7th Framework Programme for Research and Technological Development, Area "Environment", Activity 1.3.3.1 "Prediction of triggering and risk assessment for landslides".

Estimation of Groundwater Radon in North Carolina Using Land Use Regression and Bayesian Maximum Entropy.

PubMed

Messier, Kyle P; Campbell, Ted; Bradley, Philip J; Serre, Marc L

2015-08-18

Radon ((222)Rn) is a naturally occurring chemically inert, colorless, and odorless radioactive gas produced from the decay of uranium ((238)U), which is ubiquitous in rocks and soils worldwide. Exposure to (222)Rn is likely the second leading cause of lung cancer after cigarette smoking via inhalation; however, exposure through untreated groundwater is also a contributing factor to both inhalation and ingestion routes. A land use regression (LUR) model for groundwater (222)Rn with anisotropic geological and (238)U based explanatory variables is developed, which helps elucidate the factors contributing to elevated (222)Rn across North Carolina. The LUR is also integrated into the Bayesian Maximum Entropy (BME) geostatistical framework to increase accuracy and produce a point-level LUR-BME model of groundwater (222)Rn across North Carolina including prediction uncertainty. The LUR-BME model of groundwater (222)Rn results in a leave-one out cross-validation r(2) of 0.46 (Pearson correlation coefficient = 0.68), effectively predicting within the spatial covariance range. Modeled results of (222)Rn concentrations show variability among intrusive felsic geological formations likely due to average bedrock (238)U defined on the basis of overlying stream-sediment (238)U concentrations that is a widely distributed consistently analyzed point-source data.

Geologic field-trip guide to Lassen Volcanic National Park and vicinity, California

USGS Publications Warehouse

Muffler, L. J. Patrick; Clynne, Michael A.

2015-07-22

This geologic field-trip guide provides an overview of Quaternary volcanism in and around Lassen Volcanic National Park in northern California. The guide begins with a comprehensive overview of the geologic framework and the stratigraphic terminology of the Lassen region, based primarily on the “Geologic map of Lassen Volcanic National Park and vicinity” (Clynne and Muffler, 2010). The geologic overview is then followed by detailed road logs describing the volcanic features that can readily be seen in the park and its periphery. Twenty-one designated stops provide detailed explanations of important volcanic features. The guide also includes mileage logs along the highways leading into the park from the major nearby communities. The field-trip guide is intended to be a flexible document that can be adapted to the needs of a visitor approaching the park from any direction.

The worth of data in predicting aquitard continuity in hydrogeological design

NASA Astrophysics Data System (ADS)

James, Bruce R.; Freeze, R. Allan

1993-07-01

A Bayesian decision framework is developed for addressing questions of hydrogeological data worth associated with engineering design at sites in heterogeneous geological environments. The specific case investigated is one of remedial contaminant containment in an aquifer underlain by an aquitard of uncertain continuity. The framework is used to evaluate the worth of hard and soft data in investigating the aquitard's continuity. The analysis consists of four modules: (1) an aquitard realization generator based on indicator kriging, (2) a procedure for the Bayesian updating of the uncertainty with respect to aquitard windows, (3) a Monte Carlo simulation model for advective contaminant transport, and (4) an economic decision model. A sensitivity analysis for a generic design example involving a design decision between a no-action alternative and a containment alternative indicates that the data worth of a single borehole providing a hard point datum was more sensitive to economic parameters than to hydrogeological or geostatistical parameters. For this case, data worth is very sensitive to the projected cost of containment, the discount rate, and the estimated cost of failure. When it comes to hydrogeological parameters, such as the representative hydraulic conductivity of the aquitard or underlying aquifer, the sensitivity analysis indicates that it is more important to know whether the field value is above or below some threshold value than it is to know its actual numerical value. A good conceptual understanding of the site geology is important in estimating prior uncertainties. The framework was applied in a retrospective fashion to the design of a remediation program for soil contaminated by radioactive waste disposal at the Savannah River site in South Carolina. The cost-effectiveness of different patterns of boreholes was studied. A contour map is presented for the net expected value of sample information (EVSI) for a single borehole. The net EVSI of patterns of precise point measurements is also compared to that of an imprecise seismic survey.

Time Scale Optimization and the Hunt for Astronomical Cycles in Deep Time Strata

NASA Astrophysics Data System (ADS)

Meyers, Stephen R.

2016-04-01

A valuable attribute of astrochronology is the direct link between chronometer and climate change, providing a remarkable opportunity to constrain the evolution of the surficial Earth System. Consequently, the hunt for astronomical cycles in strata has spurred the development of a rich conceptual framework for climatic/oceanographic change, and has allowed exploration of the geologic record with unprecedented temporal resolution. Accompanying these successes, however, has been a persistent skepticism about appropriate astrochronologic testing and circular reasoning: how does one reliably test for astronomical cycles in stratigraphic data, especially when time is poorly constrained? From this perspective, it would seem that the merits and promise of astrochronology (e.g., a geologic time scale measured in ≤400 kyr increments) also serves as its Achilles heel, if the confirmation of such short rhythms defies rigorous statistical testing. To address these statistical challenges in astrochronologic testing, a new approach has been developed that (1) explicitly evaluates time scale uncertainty, (2) is resilient to common problems associated with spectrum confidence level assessment and 'multiple testing', and (3) achieves high statistical power under a wide range of conditions (it can identify astronomical cycles when present in data). Designated TimeOpt (for "time scale optimization"; Meyers 2015), the method employs a probabilistic linear regression model framework to investigate amplitude modulation and frequency ratios (bundling) in stratigraphic data, while simultaneously determining the optimal time scale. This presentation will review the TimeOpt method, and demonstrate how the flexible statistical framework can be further extended to evaluate (and optimize upon) complex sedimentation rate models, enhancing the statistical power of the approach, and addressing the challenge of unsteady sedimentation. Meyers, S. R. (2015), The evaluation of eccentricity-related amplitude modulation and bundling in paleoclimate data: An inverse approach for astrochronologic testing and time scale optimization, Paleoceanography, 30, doi:10.1002/ 2015PA002850.

Geohydrologic Framework of the Edwards and Trinity Aquifers, South-Central Texas

USGS Publications Warehouse

Blome, Charles D.; Faith, Jason R.; Ozuna, George B.

2007-01-01

This five-year USGS project, funded by the National Cooperative Geologic Mapping Program, is using multidisciplinary approaches to reveal the surface and subsurface geologic architecture of two important Texas aquifers: (1) the Edwards aquifer that extends from south of Austin to west of San Antonio and (2) the southern part of the Trinity aquifer in the Texas Hill Country west and south of Austin. The project's principal areas of research include: Geologic Mapping, Geophysical Surveys, Geochronology, Three-dimensional Modeling, and Noble Gas Geochemistry. The Edwards aquifer is one of the most productive carbonate aquifers in the United States. It also has been designated a sole source aquifer by the U.S. Environmental Protection Agency and is the primary source of water for San Antonio, America's eighth largest city. The Trinity aquifer forms the catchment area for the Edwards aquifer and it intercepts some surface flow above the Edwards recharge zone. The Trinity may also contribute to the Edwards water budget by subsurface flow across formation boundaries at considerable depths. Dissolution, karst development, and faulting and fracturing in both aquifers directly control aquifer geometry by compartmentalizing the aquifer and creating unique ground-water flow paths.

A Comparison of Traditional, Step-Path, and Geostatistical Techniques in the Stability Analysis of a Large Open Pit

NASA Astrophysics Data System (ADS)

Mayer, J. M.; Stead, D.

2017-04-01

With the increased drive towards deeper and more complex mine designs, geotechnical engineers are often forced to reconsider traditional deterministic design techniques in favour of probabilistic methods. These alternative techniques allow for the direct quantification of uncertainties within a risk and/or decision analysis framework. However, conventional probabilistic practices typically discretize geological materials into discrete, homogeneous domains, with attributes defined by spatially constant random variables, despite the fact that geological media display inherent heterogeneous spatial characteristics. This research directly simulates this phenomenon using a geostatistical approach, known as sequential Gaussian simulation. The method utilizes the variogram which imposes a degree of controlled spatial heterogeneity on the system. Simulations are constrained using data from the Ok Tedi mine site in Papua New Guinea and designed to randomly vary the geological strength index and uniaxial compressive strength using Monte Carlo techniques. Results suggest that conventional probabilistic techniques have a fundamental limitation compared to geostatistical approaches, as they fail to account for the spatial dependencies inherent to geotechnical datasets. This can result in erroneous model predictions, which are overly conservative when compared to the geostatistical results.

Chapter 4: Regional magnetic domains of the Circum-Arctic: A framework for geodynamic interpretation

USGS Publications Warehouse

Saltus, R.W.; Miller, E.L.; Gaina, C.; Brown, P.J.

2011-01-01

We identify and discuss 57 magnetic anomaly pattern domains spanning the Circum-Arctic. The domains are based on analysis of a new Circum-Arctic data compilation. The magnetic anomaly patterns can be broadly related to general geodynamic classification of the crust into stable, deformed (magnetic and nonmagnetic), deep magnetic high, oceanic and large igneous province domains. We compare the magnetic domains with topography/bathymetry, regional geology, regional free air gravity anomalies and estimates of the relative magnetic 'thickness' of the crust. Most of the domains and their geodynamic classification assignments are consistent with their topographic/bathymetric and geological expression. A few of the domains are potentially controversial. For example, the extent of the Iceland Faroe large igneous province as identified by magnetic anomalies may disagree with other definitions for this feature. Also the lack of definitive magnetic expression of oceanic crust in Baffin Bay, the Norwegian-Greenland Sea and the Amerasian Basin is at odds with some previous interpretations. The magnetic domains and their boundaries provide clues for tectonic models and boundaries within this poorly understood portion of the globe. ?? 2011 The Geological Society of London.

Enhancing the revision of the static geological model of the Stuttgart Formation at the Ketzin pilot site by integration of reservoir simulations and 3D seismics

NASA Astrophysics Data System (ADS)

Kempka, Thomas; Norden, Ben; Ivanova, Alexandra; Lüth, Stefan

2017-04-01

Pilot-scale carbon dioxide storage has been performed at the Ketzin pilot site in Germany from June 2007 to August 2013 with about 67 kt of CO2 injected into the Upper Triassic Stuttgart Formation. In this context, the main aims focussed on verification of the technical feasibility of CO2 storage in saline aquifers and development of efficient strategies for CO2 behaviour monitoring and prediction. A static geological model has been already developed at an early stage of this undertaking, and continuously revised with the availability of additional geological and operational data as well as by means of reservoir simulations, allowing for revisions in line with the efforts to achieve a solid history match in view of well bottomhole pressures and CO2 arrival times at the observation wells. Three 3D seismic campaigns followed the 2005 3D seismic baseline in 2009, 2012 and 2015. Consequently, the interpreted seismic data on spatial CO2 thickness distributions in the storage reservoir as well as seismic CO2 detection limits from recent conformity studies enabled us to enhance the previous history-matching results by adding a spatial component to the previous observations, limited to points only. For that purpose, we employed the latest version of the history-matched static geological reservoir model and revised the gridding scheme of the reservoir simulation model by coarsening and introducing local grid refinements at the areas of interest. Further measures to ensure computational efficiency included the application of the MUFITS reservoir simulator (BLACKOIL module) with PVT data derived from the MUFITS GASSTORE module. Observations considered in the inverse model calibration for a simulation time of about 5 years included well bottomhole pressures, CO2 arrival times and seismically determined CO2 thickness maps for 2009 and 2012. Pilot points were employed by means of the PEST++ inverse simulation framework to apply permeability multipliers, interpolated by kriging to the reservoir simulation model grid. Our results exhibit an excellent well bottomhole pressure match, good agreement with the observed CO2 arrival times at the observation wells, a reasonable agreement of the spatial CO2 distribution with the CO2 thickness maps derived from the 2009, 2012 and 2015 3D seismic campaigns as well as a good agreement with hydraulic tests conducted before CO2 injection. Hence, the inversely determined permeability multipliers provide an excellent basis for further revision of the static geological model of the Stuttgart Formation.

The Sea-Floor Mapping Facility at the U.S. Geological Survey Woods Hole Field Center, Woods Hole, Massachusetts

USGS Publications Warehouse

Deusser, Rebecca E.; Schwab, William C.; Denny, Jane F.

2002-01-01

Researchers of the sea-floor mapping facility at the U.S. Geological Survey (USGS) Woods Hole Field Center in Woods Hole, Mass., use state-of-the-art technology to produce accurate geologic maps of the sea floor. In addition to basic bathymetry and morphology, sea-floor maps may contain information about the distribution of sand resources, patterns of coastal erosion, pathways of pollutant transport, and geologic controls on marine biological habitats. The maps may also show areas of human impacts, such as disturbance by bottom fishing and pollution caused by offshore waste disposal. The maps provide a framework for scientific research and provide critical information to decisionmakers who oversee resources in the coastal ocean.

Assessment of Undiscovered Oil and Gas Resources of the Uinta-Piceance Province of Colorado and Utah, 2002

USGS Publications Warehouse

,

2002-01-01

The U.S. Geological Survey (USGS) recently completed an assessment of the undiscovered oil and gas potential of the UintaPiceance Province of northwestern Colorado and northeastern Utah (fig. 1). The assessment of the Uinta-Piceance Province is geology based and uses the Total Petroleum System concept. The geologic elements of Total Petroleum Systems include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy, petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined five Total Petroleum Systems and 20 Assessment Units within these Total Petroleum Systems, and quantitatively estimated the undiscovered oil and gas resources within each Assessment Unit (table 1).

Deep Time Framework: A Preliminary Study of U.K. Primary Teachers' Conceptions of Geological Time and Perceptions of Geoscience.

ERIC Educational Resources Information Center

Trend, Roger David

2001-01-01

Studies (n=51) inservice school teachers with regard to their orientations toward geoscience phenomena in general and deep time in particular. Aims to identify the nature of idiosyncratic conceptions of deep time and propose a curricular Deep Time Framework for teacher education. (Contains 29 references.) (Author/YDS)

Ross Ice Shelf, Antarctica: Bathymetry, Structural Geology and Ocean Circulation from New IcePod Airborne Geophysical Data

NASA Astrophysics Data System (ADS)

Siddoway, C. S.; Tinto, K. J.; Bell, R. E.; Padman, L.; Fricker, H. A.; Springer, S. R.

2016-12-01

Rock exposures in the Ford Ranges, Marie Byrd Land (MBL), on the eastern margin of the Ross Embayment, contain direct evidence of the geological processes that led to formation of West Antarctica's continental lithosphere. Processes include wide regional extension, volcanism, and thermal reequilibration, with creation of crustal structures that are prone to reactivation today. Marie Byrd Land is tectonically active, as is evident from Late Pleistocene to Holocene eruptive centers, englacial volcanic tephra as young as 2200 years, a site of magma propagation inferred from POLEnet seismic records, and the occurrence of a 2012 earthquake cluster of magnitude M4.4 to M5.5 north of Edward VII Peninsula. However, the lithosphere underlying the Ross Ice Shelf (RIS) is poorly known due to the thick cover of shelf ice floating on the ocean, difficult to penetrate by satellite remote sensing or other methods. Airborne geophysical data for the Ford Ranges and the Ross Ice Shelf (RIS) suggest that the rock formations and structures that underlie MBL continue beneath the RIS. Notable features known in outcrop and detected/inferred from potential fields data are Pleistocene or younger mafic volcanic centers and Cretaceous core complexes, both likely associated with wrench faults. The Ford Ranges legacy dataset that now provides a fundamental basis for sub-RIS geological interpretation is a product of research in coastal MBL led by B.P. Luyendyk from 1989 - 2006. To improve our knowledge of lithospheric evolution, identify active faults and prospective zones of volcanism/heat flow, and to determine the sub-RIS bathymetry, the RIS sector is being explored via new Icepod aerogeophysics acquisition during the ROSETTA-Ice project (Ross Ocean and ice Shelf Environment, and Tectonic setting Through Aerogeophysical surveys and modeling), now underway over this vast under-explored sector of the Ross Embayment. ROSETTA-Ice collects and employs new gravity data with magnetics to delineate sediments, bedrock geological units, and faults beneath the RIS, then model bathymetry. This poster will share preliminary results and interpretations. The improved characterization of the subglacial geology and bathymetry will aid in refinement of the tectonic framework and models of oceanographic circulation, with bearing on RIS stability.

Efficient Geological Modelling of Large AEM Surveys

NASA Astrophysics Data System (ADS)

Bach, Torben; Martlev Pallesen, Tom; Jørgensen, Flemming; Lundh Gulbrandsen, Mats; Mejer Hansen, Thomas

2014-05-01

Combining geological expert knowledge with geophysical observations into a final 3D geological model is, in most cases, not a straight forward process. It typically involves many types of data and requires both an understanding of the data and the geological target. When dealing with very large areas, such as modelling of large AEM surveys, the manual task for the geologist to correctly evaluate and properly utilise all the data available in the survey area, becomes overwhelming. In the ERGO project (Efficient High-Resolution Geological Modelling) we address these issues and propose a new modelling methodology enabling fast and consistent modelling of very large areas. The vision of the project is to build a user friendly expert system that enables the combination of very large amounts of geological and geophysical data with geological expert knowledge. This is done in an "auto-pilot" type functionality, named Smart Interpretation, designed to aid the geologist in the interpretation process. The core of the expert system is a statistical model that describes the relation between data and geological interpretation made by a geological expert. This facilitates fast and consistent modelling of very large areas. It will enable the construction of models with high resolution as the system will "learn" the geology of an area directly from interpretations made by a geological expert, and instantly apply it to all hard data in the survey area, ensuring the utilisation of all the data available in the geological model. Another feature is that the statistical model the system creates for one area can be used in another area with similar data and geology. This feature can be useful as an aid to an untrained geologist to build a geological model, guided by the experienced geologist way of interpretation, as quantified by the expert system in the core statistical model. In this project presentation we provide some examples of the problems we are aiming to address in the project, and show some preliminary results.

On the importance of geological data for hydraulic tomography analysis: Laboratory sandbox study

NASA Astrophysics Data System (ADS)

Zhao, Zhanfeng; Illman, Walter A.; Berg, Steven J.

2016-11-01

This paper investigates the importance of geological data in Hydraulic Tomography (HT) through sandbox experiments. In particular, four groundwater models with homogeneous geological units constructed with borehole data of varying accuracy are jointly calibrated with multiple pumping test data of two different pumping and observation densities. The results are compared to those from a geostatistical inverse model. Model calibration and validation performances are quantitatively assessed using drawdown scatterplots. We find that accurate and inaccurate geological models can be well calibrated, despite the estimated K values for the poor geological models being quite different from the actual values. Model validation results reveal that inaccurate geological models yield poor drawdown predictions, but using more calibration data improves its predictive capability. Moreover, model comparisons among a highly parameterized geostatistical and layer-based geological models show that, (1) as the number of pumping tests and monitoring locations are reduced, the performance gap between the approaches decreases, and (2) a simplified geological model with a fewer number of layers is more reliable than the one based on the wrong description of stratigraphy. Finally, using a geological model as prior information in geostatistical inverse models results in the preservation of geological features, especially in areas where drawdown data are not available. Overall, our sandbox results emphasize the importance of incorporating geological data in HT surveys when data from pumping tests is sparse. These findings have important implications for field applications of HT where well distances are large.

Geologic Storage at the Basin Scale: Region-Based Basin Modeling, Powder River Basin (PRB), NE Wyoming and SE Montana

NASA Astrophysics Data System (ADS)

Melick, J. J.; Gardner, M. H.

2008-12-01

Carbon capture and storage from the over 2000 power plants is estimated at 3-5 GT/yr, which requires large- scale geologic storage of greenhouse gasses in sedimentary basins. Unfortunately, determination of basin scale storage capacity is currently based on oversimplified geologic models that are difficult to validate. Simplification involves reducing the number of geologic parameters incorporated into the model, modeling with large grid cells, and treatment of subsurface reservoirs as homogeneous media. The latter problem reflects the focus of current models on fluid and/or fluid-rock interactions rather than fluid movement and migration pathways. For example, homogeneous models over emphasize fluid behavior, like the buoyancy of super-critical CO2, and hence overestimate leakage rates. Fluid mixing and fluid-rock interactions cannot be assessed with models that only investigate these reactions at a human time scale. Preliminary and conservative estimates of the total pore volume for the PRB suggest 200 GT of supercritical CO2 can be stored in this typical onshore sedimentary basin. The connected pore volume (CPV) however is not included in this estimate. Geological characterization of the CPV relates subsurface storage units to the most prolific reservoir classes (RCs). The CPV, number of well penetrations, supercritical storage area, and potential leakage pathways characterize each RC. Within each RC, a hierarchy of stratigraphic cycles is populated with stationary sedimentation regions that control rock property distributions by correlating environment of deposition (EOD) to CPV. The degree to which CPV varies between RCs depends on the geology and attendant heterogeneity retained in the fluid flow model. Region-based modeling of the PRB incorporates 28000 wells correlated across a 70,000 Km2 area, 2 km thick on average. Within this basin, five of the most productive RCs were identified from production history and placed in a fourfold stratigraphic framework (second- through fourth-order cycles). Within the small- scale 4th-order sequences (30-150-m thick, 16 total), sedimentation regions, each corresponding to an EOD, are defined by thickness, lithology and core-calibrated well-log patterns. This talk illustrates the workflow by focusing on one of the 16 layers in the basin-scale model. Isopach maps from this sample layer conform to depositional patterns confirmed through definition of five core-calibrated, well-log defined sedimentation regions. Lithology distributions also conform to thickness trends in nearshore deltas, but not in offshore regions, where sand-rich and sheet-like, but thin-bedded sandstones are flanked by mud-rich intervals of equivalent thickness. These maps represent sedimentation patterns confined by basal erosional sequence boundary and basin-wide bentonite, yet containing up to seven high-frequency sequence boundaries. To illustrate over simplification problems in this same layer, a 14000 km2 sample area is 600 km3 and using standard averaging methods, which are considered to be geologic in origin, the CPV is 16 km3. However, averaging increases connectivity with high CPV more uniformly distributed; significantly, the key mud belt region separating nearshore from offshore sandstones is not represented. Region-based modeling of this layer yields 13 km3 (110 Bbl). Furthermore, significant vertical leakage may exist from the 20000 well penetrations and faults and fractures along the western basin margin. This example illustrates the importance of accurately characterizing heterogeneity and distributing CPV using sedimentation regions.

A geological reconnaissance of electrical and electronic waste as a source for rare earth metals.

PubMed

Mueller, Sandra R; Wäger, Patrick A; Widmer, Rolf; Williams, Ian D

2015-11-01

The mining of material resources requires knowledge about geogenic and anthropogenic deposits, in particular on the location of the deposits with the comparatively highest concentration of raw materials. In this study, we develop a framework that allows the establishment of analogies between geological and anthropogenic processes. These analogies were applied to three selected products containing rare earth elements (REE) in order to identify the most concentrated deposits in the anthropogenic cycle. The three identified anthropogenic deposits were characterised according to criteria such as "host rock", "REE mineralisation" and "age of mineralisation", i.e. regarding their "geological" setting. The results of this characterisation demonstrated that anthropogenic deposits have both a higher concentration of REE and a longer mine life than the evaluated geogenic deposit (Mount Weld, Australia). The results were further evaluated by comparison with the geological knowledge category of the United Nations Framework Classification for Fossil Energy and Mineral Reserves and Resources 2009 (UNFC-2009) to determine the confidence level in the deposit quantities. The application of our approach to the three selected cases shows a potential for recovery of REE in anthropogenic deposits; however, further exploration of both potential and limitations is required. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Summary on several key techniques in 3D geological modeling.

PubMed

Mei, Gang

2014-01-01

Several key techniques in 3D geological modeling including planar mesh generation, spatial interpolation, and surface intersection are summarized in this paper. Note that these techniques are generic and widely used in various applications but play a key role in 3D geological modeling. There are two essential procedures in 3D geological modeling: the first is the simulation of geological interfaces using geometric surfaces and the second is the building of geological objects by means of various geometric computations such as the intersection of surfaces. Discrete geometric surfaces that represent geological interfaces can be generated by creating planar meshes first and then spatially interpolating; those surfaces intersect and then form volumes that represent three-dimensional geological objects such as rock bodies. In this paper, the most commonly used algorithms of the key techniques in 3D geological modeling are summarized.

Designing and Implementing a Retrospective Earthquake Detection Framework at the U.S. Geological Survey National Earthquake Information Center

NASA Astrophysics Data System (ADS)

Patton, J.; Yeck, W.; Benz, H.

2017-12-01

The U.S. Geological Survey National Earthquake Information Center (USGS NEIC) is implementing and integrating new signal detection methods such as subspace correlation, continuous beamforming, multi-band picking and automatic phase identification into near-real-time monitoring operations. Leveraging the additional information from these techniques help the NEIC utilize a large and varied network on local to global scales. The NEIC is developing an ordered, rapid, robust, and decentralized framework for distributing seismic detection data as well as a set of formalized formatting standards. These frameworks and standards enable the NEIC to implement a seismic event detection framework that supports basic tasks, including automatic arrival time picking, social media based event detections, and automatic association of different seismic detection data into seismic earthquake events. In addition, this framework enables retrospective detection processing such as automated S-wave arrival time picking given a detected event, discrimination and classification of detected events by type, back-azimuth and slowness calculations, and ensuring aftershock and induced sequence detection completeness. These processes and infrastructure improve the NEIC's capabilities, accuracy, and speed of response. In addition, this same infrastructure provides an improved and convenient structure to support access to automatic detection data for both research and algorithmic development.

Integration of borehole and seismic data to unravel complex stratigraphy: Case studies from the Mannville Group, Western Canada

NASA Astrophysics Data System (ADS)

Sarzalejo Silva, Sabrina Ester

Understanding the stratigraphic architecture of geologically complex reservoirs, such as the heavy oil deposits of Western Canada, is essential to achieve an efficient hydrocarbon recovery. Borehole and 3-D seismic data were integrated to define the stratigraphic architecture and generate 3-dimensional geological models of the Mannville Group in Saskatchewan. The Mannville is a stratigraphically complex unit formed of fluvial to marine deposits. Two areas in west-central and southern Saskatchewan were examined in this study. In west-central Saskatchewan, the area corresponds to a stratigraphically controlled heavy oil reservoir with production from the undifferentiated Dina-Cummings Members of the Lower Cretaceous Mannville Group. The southern area, although non-prospective for hydrocarbons, shares many similarities with time-equivalent strata in areas of heavy oil production. Seismic sequence stratigraphic principles together with log signatures permitted the subdivision of the Mannville into different packages. An initial geological model was generated integrating seismic and well-log data Multiattribute analysis and neural networks were used to generate a pseudo-lithology or gamma-ray volume. The incorporation of borehole core data to the model and the subsequent integration with the lithological prediction were crucial to capture the distribution of reservoir and non-reservoir deposits in the study area. The ability to visualize the 3-D seismic data in a variety of ways, including arbitrary lines and stratal or horizon slicing techniques helped the definition of stratigraphic features such as channels and scroll bars that affect fluid flow in hydrocarbon producing areas. Small-scale heterogeneities in the reservoir were not resolved due to the resolution of the seismic data. Although not undertaken in this study, the resulting stratigraphic framework could be used to help construct a static reservoir model. Because of the small size of the 3-D seismic surveys, horizontal slices through the data volume generally imaged only small portions of the paleogeomorphologic features thought to be present in this area. As such, it was only through the integration of datasets that the geological models were established.

Coupling of geochemical and multiphase flow processes for validation of the MUFITS reservoir simulator against TOUGHREACT

NASA Astrophysics Data System (ADS)

De Lucia, Marco; Kempka, Thomas; Afanasyev, Andrey; Melnik, Oleg; Kühn, Michael

2016-04-01

Coupled reactive transport simulations, especially in heterogeneous settings considering multiphase flow, are extremely time consuming and suffer from significant numerical issues compared to purely hydrodynamic simulations. This represents a major hurdle in the assessment of geological subsurface utilization, since it constrains the practical application of reactive transport modelling to coarse spatial discretization or oversimplified geological settings. In order to overcome such limitations, De Lucia et al. [1] developed and validated a one-way coupling approach between geochemistry and hydrodynamics, which is particularly well suited for CO2 storage simulations, while being of general validity. In the present study, the models used for the validation of the one-way coupling approach introduced by De Lucia et al. (2015), and originally performed with the TOUGHREACT simulator, are transferred to and benchmarked against the multiphase reservoir simulator MUFITS [2]. The geological model is loosely inspired by an existing CO2 storage site. Its grid comprises 2,950 elements enclosed in a single layer, but reflecting a realistic three-dimensional anticline geometry. For the purpose of this comparison, homogeneous and heterogeneous scenarios in terms of porosity and permeability were investigated. In both cases, the results of the MUFITS simulator are in excellent agreement with those produced with the fully-coupled TOUGHREACT simulator, while profiting from significantly higher computational performance. This study demonstrates how a computationally efficient simulator such as MUFITS can be successfully included in a coupled process simulation framework, and also suggests ameliorations and specific strategies for the coupling of chemical processes with hydrodynamics and heat transport, aiming at tackling geoscientific problems beyond the storage of CO2. References [1] De Lucia, M., Kempka, T., and Kühn, M. A coupling alternative to reactive transport simulations for long-term prediction of chemical reactions in heterogeneous CO2 storage systems, Geosci. Model Dev., 8, 279-294, 2015, doi:10.5194/gmd-8-279-2015 [2] Afanasyev, A.A. Application of the reservoir simulator MUFITS for 3D modeling of CO2 storage in geological formations, Energy Procedia, 40, 365-374, 2013, doi:10.1016/j.egypro.2013.08.042

Section-constrained local geological interface dynamic updating method based on the HRBF surface

NASA Astrophysics Data System (ADS)

Guo, Jiateng; Wu, Lixin; Zhou, Wenhui; Li, Chaoling; Li, Fengdan

2018-02-01

Boundaries, attitudes and sections are the most common data acquired from regional field geological surveys, and they are used for three-dimensional (3D) geological modelling. However, constructing topologically consistent 3D geological models from rapid and automatic regional modelling with convenient local modifications remains unresolved. In previous works, the Hermite radial basis function (HRBF) surface was introduced for the simulation of geological interfaces from geological boundaries and attitudes, which allows 3D geological models to be automatically extracted from the modelling area by the interfaces. However, the reasonability and accuracy of non-supervised subsurface modelling is limited without further modifications generated through explanations and analyses performed by geology experts. In this paper, we provide flexible and convenient manual interactive manipulation tools for geologists to sketch constraint lines, and these tools may help geologists transform and apply their expert knowledge to the models. In the modified modelling workflow, the geological sections were treated as auxiliary constraints to construct more reasonable 3D geological models. The geometric characteristics of section lines were abstracted to coordinates and normal vectors, and along with the transformed coordinates and vectors from boundaries and attitudes, these characteristics were adopted to co-calculate the implicit geological surface function parameters of the HRBF equations and form constrained geological interfaces from topographic (boundaries and attitudes) and subsurface data (sketched sections). Based on this new modelling method, a prototype system was developed, in which the section lines could be imported from databases or interactively sketched, and the models could be immediately updated after the new constraints were added. Experimental comparisons showed that all boundary, attitude and section data are well represented in the constrained models, which are consistent with expert explanations and help improve the quality of the models.

Visible Geology - Interactive online geologic block modelling

NASA Astrophysics Data System (ADS)

Cockett, R.

2012-12-01

Geology is a highly visual science, and many disciplines require spatial awareness and manipulation. For example, interpreting cross-sections, geologic maps, or plotting data on a stereonet all require various levels of spatial abilities. These skills are often not focused on in undergraduate geoscience curricula and many students struggle with spatial relations, manipulations, and penetrative abilities (e.g. Titus & Horsman, 2009). A newly developed program, Visible Geology, allows for students to be introduced to many geologic concepts and spatial skills in a virtual environment. Visible Geology is a web-based, three-dimensional environment where students can create and interrogate their own geologic block models. The program begins with a blank model, users then add geologic beds (with custom thickness and color) and can add geologic deformation events like tilting, folding, and faulting. Additionally, simple intrusive dikes can be modelled, as well as unconformities. Students can also explore the interaction of geology with topography by drawing elevation contours to produce their own topographic models. Students can not only spatially manipulate their model, but can create cross-sections and boreholes to practice their visual penetrative abilities. Visible Geology is easy to access and use, with no downloads required, so it can be incorporated into current, paper-based, lab activities. Sample learning activities are being developed that target introductory and structural geology curricula with learning objectives such as relative geologic history, fault characterization, apparent dip and thickness, interference folding, and stereonet interpretation. Visible Geology provides a richly interactive, and immersive environment for students to explore geologic concepts and practice their spatial skills.; Screenshot of Visible Geology showing folding and faulting interactions on a ridge topography.

Integrating surrogate models into subsurface simulation framework allows computation of complex reactive transport scenarios

NASA Astrophysics Data System (ADS)

De Lucia, Marco; Kempka, Thomas; Jatnieks, Janis; Kühn, Michael

2017-04-01

Reactive transport simulations - where geochemical reactions are coupled with hydrodynamic transport of reactants - are extremely time consuming and suffer from significant numerical issues. Given the high uncertainties inherently associated with the geochemical models, which also constitute the major computational bottleneck, such requirements may seem inappropriate and probably constitute the main limitation for their wide application. A promising way to ease and speed-up such coupled simulations is achievable employing statistical surrogates instead of "full-physics" geochemical models [1]. Data-driven surrogates are reduced models obtained on a set of pre-calculated "full physics" simulations, capturing their principal features while being extremely fast to compute. Model reduction of course comes at price of a precision loss; however, this appears justified in presence of large uncertainties regarding the parametrization of geochemical processes. This contribution illustrates the integration of surrogates into the flexible simulation framework currently being developed by the authors' research group [2]. The high level language of choice for obtaining and dealing with surrogate models is R, which profits from state-of-the-art methods for statistical analysis of large simulations ensembles. A stand-alone advective mass transport module was furthermore developed in order to add such capability to any multiphase finite volume hydrodynamic simulator within the simulation framework. We present 2D and 3D case studies benchmarking the performance of surrogates and "full physics" chemistry in scenarios pertaining the assessment of geological subsurface utilization. [1] Jatnieks, J., De Lucia, M., Dransch, D., Sips, M.: "Data-driven surrogate model approach for improving the performance of reactive transport simulations.", Energy Procedia 97, 2016, p. 447-453. [2] Kempka, T., Nakaten, B., De Lucia, M., Nakaten, N., Otto, C., Pohl, M., Chabab [Tillner], E., Kühn, M.: "Flexible Simulation Framework to Couple Processes in Complex 3D Models for Subsurface Utilization Assessment.", Energy Procedia, 97, 2016 p. 494-501.

Multiphase modeling of geologic carbon sequestration in saline aquifers.

PubMed

Bandilla, Karl W; Celia, Michael A; Birkholzer, Jens T; Cihan, Abdullah; Leister, Evan C

2015-01-01

Geologic carbon sequestration (GCS) is being considered as a climate change mitigation option in many future energy scenarios. Mathematical modeling is routinely used to predict subsurface CO2 and resident brine migration for the design of injection operations, to demonstrate the permanence of CO2 storage, and to show that other subsurface resources will not be degraded. Many processes impact the migration of CO2 and brine, including multiphase flow dynamics, geochemistry, and geomechanics, along with the spatial distribution of parameters such as porosity and permeability. In this article, we review a set of multiphase modeling approaches with different levels of conceptual complexity that have been used to model GCS. Model complexity ranges from coupled multiprocess models to simplified vertical equilibrium (VE) models and macroscopic invasion percolation models. The goal of this article is to give a framework of conceptual model complexity, and to show the types of modeling approaches that have been used to address specific GCS questions. Application of the modeling approaches is shown using five ongoing or proposed CO2 injection sites. For the selected sites, the majority of GCS models follow a simplified multiphase approach, especially for questions related to injection and local-scale heterogeneity. Coupled multiprocess models are only applied in one case where geomechanics have a strong impact on the flow. Owing to their computational efficiency, VE models tend to be applied at large scales. A macroscopic invasion percolation approach was used to predict the CO2 migration at one site to examine details of CO2 migration under the caprock. © 2015, National Ground Water Association.

High-resolution geologic mapping of the inner continental shelf: Nahant to Gloucester, Massachusetts

USGS Publications Warehouse

Barnhardt, Walter A.; Andrews, Brian D.; Butman, Bradford

2006-01-01

This report presents high-resolution maps of the seafloor offshore of Massachusetts, from Nahant to Gloucester. Approximately 134 km² of the inner shelf were mapped with a focus on the nearshore region in water depths less than 40 m (fig. 1.1). The maps were prepared as part of a cooperative mapping program between the U.S. Geological Survey (USGS) and the Massachusetts Office of Coastal Zone Management (CZM). They are based on marine geophysical data, sediment sampling, and bottom photography obtained on two research cruises carried out in 2003 and 2004. The primary objective of this program is to develop a suite of seafloor maps that provide geologic information for management of coastal and marine resources. Accurate maps of seafloor geology are important first steps toward protecting fish habitat, delineating marine reserves, and assessing environmental changes due to natural or human impacts. The maps also provide a geologic framework for scientific research, industry and the public. The organization of this report is outlined in the navigation bar along the left-hand margin of the page. This is section 1, the introduction. Section 2 briefly describes the mapping products contained in this report and has links to large-format map sheets, that can be viewed on line or downloaded. Section 3 is a description of the data collection, processing, and analysis procedures used to create the map products. Section 4 examines the geologic framework and late Quaternary evolution of the region, and presents two different strategies for mapping the complex seafloor. This report also contains four appendices that include GIS layers of all data collected in this study, and copies of the sample and photographic data used to validate the interpretations.

Petroleum Systems and Geologic Assessment of Oil and Gas Resources in the Wind River Basin Province, Wyoming

USGS Publications Warehouse

,

2007-01-01

The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The U.S. Geological Survey (USGS) recently completed an assessment of the undiscovered oil and gas potential of the Wind River Basin Province which encompasses about 4.7 million acres in central Wyoming. The assessment is based on the geologic elements of each total petroleum system (TPS) defined in the province, including hydrocarbon source rocks (source-rock maturation, hydrocarbon generation, and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined three TPSs: (1) Phosphoria TPS, (2) Cretaceous-Tertiary TPS, and (3) Waltman TPS. Within these systems, 12 Assessment Units (AU) were defined and undiscovered oil and gas resources were quantitatively estimated within 10 of the 12 AUs.

Petroleum Systems and Geologic Assessment of Undiscovered Oil and Gas, Navarro and Taylor Groups, Western Gulf Province, Texas

USGS Publications Warehouse

,

2006-01-01

The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas potential of the Late Cretaceous Navarro and Taylor Groups in the Western Gulf Province in Texas (USGS Province 5047). The Navarro and Taylor Groups have moderate potential for undiscovered oil resources and good potential for undiscovered gas resources. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define one total petroleum system and five assessment units. Five assessment units were quantitatively assessed for undiscovered oil and gas resources.

Building a geological reference platform using sequence stratigraphy combined with geostatistical tools

NASA Astrophysics Data System (ADS)

Bourgine, Bernard; Lasseur, Éric; Leynet, Aurélien; Badinier, Guillaume; Ortega, Carole; Issautier, Benoit; Bouchet, Valentin

2015-04-01

In 2012 BRGM launched an extensive program to build the new French Geological Reference platform (RGF). Among the objectives of this program is to provide the public with validated, reliable and 3D-consistent geological data, with estimation of uncertainty. Approx. 100,000 boreholes over the whole French national territory provide a preliminary interpretation in terms of depths of main geological interfaces, but with an unchecked, unknown and often low reliability. The aim of this paper is to present the procedure that has been tested on two areas in France, in order to validate (or not) these boreholes, with the aim of being generalized as much as possible to the nearly 100,000 boreholes waiting for validation. The approach is based on the following steps, and includes the management of uncertainty at different steps: (a) Selection of a loose network of boreholes owning a logging or coring information enabling a reliable interpretation. This first interpretation is based on the correlation of well log data and allows defining 3D sequence stratigraphic framework identifying isochronous surfaces. A litho-stratigraphic interpretation is also performed. Be "A" the collection of all boreholes used for this step (typically 3 % of the total number of holes to be validated) and "B" the other boreholes to validate, (b) Geostatistical analysis of characteristic geological interfaces. The analysis is carried out firstly on the "A" type data (to validate the variogram model), then on the "B" type data and at last on "B" knowing "A". It is based on cross-validation tests and evaluation of the uncertainty associated to each geological interface. In this step, we take into account inequality constraints provided by boreholes that do not intersect all interfaces, as well as the "litho-stratigraphic pile" defining the formations and their relationships (depositing surfaces or erosion). The goal is to identify quickly and semi-automatically potential errors among the data, up to the geologist to check and correct the anomalies, (c) Consistency tests are also used to verify the appropriateness of interpretations towards other constraints (geological map, maximal formation extension limits, digital terrain model ...), (d) Construction of a 3D geological model from "A"+ "B" boreholes: continuous surfaces representation makes it possible to assess the overall consistency and to validate or invalidate interpretations. Standard-deviation maps allow visualizing areas where data from available but not yet validated boreholes could be added to reduce uncertainty. Maps of absolute or relative errors help to quantify and visualize model uncertainty. This procedure helps to quickly identify the main errors in the data. It guarantees rationalization, reproducibility and traceability of the various stages of validation. Automation aspect is obviously important when it comes to dealing with datasets that can contain tens of thousands of surveys. For this, specific tools have been developed by BRGM (GDM/ MultiLayer software, R scripts, GIS tools).

Assessment of undiscovered oil and gas resources of the Williston Basin Province of North Dakota, Montana, and South Dakota, 2010

USGS Publications Warehouse

,

2011-01-01

Using a geology-based assessment method, the U.S. Geological Survey estimated mean undiscovered volumes of 3.8 billion barrels of undiscovered oil, 3.7 trillion cubic feet of associated/dissolved natural gas, and 0.2 billion barrels of undiscovered natural gas liquids in the Williston Basin Province, North Dakota, Montana, and South Dakota. The U.S. Geological Survey (USGS) recently completed a comprehensive oil and gas assessment of the Williston Basin, which encompasses more than 90 million acres in parts of North Dakota, eastern Montana, and northern South Dakota. The assessment is based on the geologic elements of each total petroleum system (TPS) defined in the province, including hydrocarbon source rocks (source-rock maturation, hydrocarbon generation, and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined 11 TPS and 19 Assessment Units (AU).

Preliminary Geologic Map of the Buxton 7.5' Quadrangle, Washington County, Oregon

USGS Publications Warehouse

Dinterman, Philip A.; Duvall, Alison R.

2009-01-01

This map, compiled from previously published and unpublished data, and new mapping by the authors, represents the general distribution of bedrock and surficial deposits of the Buxton 7.5-minute quadrangle. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:24,000 or smaller. This plot file and accompanying database depict the distribution of geologic materials and structures at a regional (1:24,000) scale. The report is intended to provide geologic information for the regional study of materials properties, earthquake shaking, landslide potential, mineral hazards, seismic velocity, and earthquake faults. In addition, the report contains new information and interpretations about the regional geologic history and framework. However, the regional scale of this report does not provide sufficient detail for site development purposes.

Using 'How People Learn' as a Blueprint for Developing Teaching Strategies in an Introductory Geology Course

NASA Astrophysics Data System (ADS)

Debari, S. M.; Bachmann, J.; Dougan, B.; Fackler-Adams, B.; Kratz, R.; Linneman, S.; Plake, T.; Smith, B.

2008-12-01

A new curriculum for an introductory geology course, Geology and Everyday Thinking (GET), incorporates the key research findings of How People Learn (NAS, 1999), and is based on the pedagogical approach of Physics and Everyday Thinking (PET; http://petproject.sdsu.edu/). These key findings have profound implications for developing teaching strategies that promote student learning. They suggest that for learning to occur: 1) students' preconceptions must be engaged, 2) students must be able to build their own conceptual framework, and 3) students must be given an opportunity to reflect on their learning (metacognition). Our curriculum has been carefully constructed into cycles that apply these key findings while exploring a key geologic concept. Each cycle engages students' 'Initial Ideas' about these concepts (and continuously revisits those Initial Ideas), sequentially builds upon concepts in a logical framework, and requires reflective writing. The curriculum employs questioning, small group work, and small and large class discussions. Students construct concepts by doing inquiry lab activities, but embedded group discussions that promote discourse and questioning among students is a crucial tool in the sense-making and solidification of those concepts. The questioning and discourse occur throughout each module so that students' preconceptions about a particular concept are brought out early on, and are revisited and challenged again as students construct their new understanding. Whiteboarding, or the process of sharing small-group ideas to a larger group, is the primary method of generating discussion. The instructor's role as facilitator and questioner is the cornerstone in this process. The primary audience for this course is future elementary teachers, who are required take a year-long science sequence. The year-long sequence includes physics (PET), geology (GET), and a correlative new curriculum in biology (BET). Class size is limited to 24 students, and the sequence is taught at a 4-year university as well as at four regional feeder community colleges. These courses model an inquiry-based teaching methodology that our pre-service teachers will use to teach science to their future students. Both quantitative and qualitative assessment data collected from our students show impressive gains both in attitudes about science and science content, especially compared to larger lecture-based introductory courses.

Investigation of the geology and hydrology of the Coconino Plateau of northern Arizona: a project of the Arizona Rural Watershed Initiative

USGS Publications Warehouse

Flynn, Marilyn E.; Bills, Donald J.

2002-01-01

The water resources of the Coconino Plateau in northern Arizona are under increasing demand as a result of development. The population of this arid region continues to grow, and the number of visitors to the many national and state parks and monuments in the region has increased annually. The sustainability, protection, and maintenance of springs and seeps and associated riparian habitat on the Coconino Plateau are major issues that have broad public and governmental support. Regional stakeholders agree that an improved understanding of the regional hydrogeologic system is needed to address the concerns of water supply and ground-water sustainability. The base of information required to adequately describe the hydrogeology of the Coconino Plateau currently does not exist. Hydrogeologic data is most abundant for large population centers like Flagstaff and Sedona, but is sparse for less populated areas like Williams, Tusayan, Valle, and Cameron. There are still large parts of the Coconino Plateau for which there is no basic geologic or hydrologic information available. In order to develop a hydrogeologic framework for the Coconino Plateau, a comprehensive effort is needs to compile existent data and collect additional data to fill in data gaps and reinforce limited information. In 1999, the U.S. Geological Survey (USGS) began an assessment of the hydrogeology of the Coconino Plateau in cooperation with the Arizona Department of Water Resources (ADWR) as part of the Rural Watershed Initiative, a program established by the State of Arizona and managed by the ADWR. Assessments also are underway in the upper-middle Verde River watershed (Woodhouse and others, 2002) to the south and in the Mogollon Highlands to the southeast (Parker and Flynn, 2000). Each study has as its objectives: (1) the collection, compilation, and evaluation of all existing geologic, hydrologic, and related data pertaining to the study area and the creation of a database that is readily accessible to the public and (2) the development of an understanding of the hydrogeologic framework, which is the relation between hydrologic and geologic properties, that can be used for water-resources management purposes and that will support the development of conceptual and interpretive models that can be used to evaluate the effects of climate and water use on regional water resources.

Research and implementation on 3D modeling of geological body

NASA Astrophysics Data System (ADS)

Niu, Lijuan; Li, Ligong; Zhu, Renyi; Huang, Man

2017-10-01

This study based on GIS thinking explores the combination of the mixed spatial data model and GIS model to build three-dimensional(3d) model of geological bodies in the Arc Engine platform, describes the interface and method used in the construction of 3d geological body in Arc Engine component platform in detail, and puts forward an indirect method which constructs a set of geological grid layers through Rigging interpolation by the borehole data and then converts it into the geological layers of TIN, which improves the defect in building the geological layers of TIN directly and makes it better to complete the simulation of the real geological layer. This study makes a useful attempt to build 3d model of the geological body based on the GIS, and provides a certain reference value for simulating geological bodies in 3d and constructing the digital system of underground space.

Summary on Several Key Techniques in 3D Geological Modeling

PubMed Central

2014-01-01

Several key techniques in 3D geological modeling including planar mesh generation, spatial interpolation, and surface intersection are summarized in this paper. Note that these techniques are generic and widely used in various applications but play a key role in 3D geological modeling. There are two essential procedures in 3D geological modeling: the first is the simulation of geological interfaces using geometric surfaces and the second is the building of geological objects by means of various geometric computations such as the intersection of surfaces. Discrete geometric surfaces that represent geological interfaces can be generated by creating planar meshes first and then spatially interpolating; those surfaces intersect and then form volumes that represent three-dimensional geological objects such as rock bodies. In this paper, the most commonly used algorithms of the key techniques in 3D geological modeling are summarized. PMID:24772029

New Inversion and Interpretation of Public-Domain Electromagnetic Survey Data from Selected Areas in Alaska

NASA Astrophysics Data System (ADS)

Smith, B. D.; Kass, A.; Saltus, R. W.; Minsley, B. J.; Deszcz-Pan, M.; Bloss, B. R.; Burns, L. E.

2013-12-01

Public-domain airborne geophysical surveys (combined electromagnetics and magnetics), mostly collected for and released by the State of Alaska, Division of Geological and Geophysical Surveys (DGGS), are a unique and valuable resource for both geologic interpretation and geophysical methods development. A new joint effort by the US Geological Survey (USGS) and the DGGS aims to add value to these data through the application of novel advanced inversion methods and through innovative and intuitive display of data: maps, profiles, voxel-based models, and displays of estimated inversion quality and confidence. Our goal is to make these data even more valuable for interpretation of geologic frameworks, geotechnical studies, and cryosphere studies, by producing robust estimates of subsurface resistivity that can be used by non-geophysicists. The available datasets, which are available in the public domain, include 39 frequency-domain electromagnetic datasets collected since 1993, and continue to grow with 5 more data releases pending in 2013. The majority of these datasets were flown for mineral resource purposes, with one survey designed for infrastructure analysis. In addition, several USGS datasets are included in this study. The USGS has recently developed new inversion methodologies for airborne EM data and have begun to apply these and other new techniques to the available datasets. These include a trans-dimensional Markov Chain Monte Carlo technique, laterally-constrained regularized inversions, and deterministic inversions which include calibration factors as a free parameter. Incorporation of the magnetic data as an additional constraining dataset has also improved the inversion results. Processing has been completed in several areas, including Fortymile and the Alaska Highway surveys, and continues in others such as the Styx River and Nome surveys. Utilizing these new techniques, we provide models beyond the apparent resistivity maps supplied by the original contractors, allowing us to produce a variety of products, such as maps of resistivity as a function of depth or elevation, cross section maps, and 3D voxel models, which have been treated consistently both in terms of processing and error analysis throughout the state. These products facilitate a more fruitful exchange between geologists and geophysicists and a better understanding of uncertainty, and the process results in iterative development and improvement of geologic models, both on small and large scales.

Preliminary Modelling of the Effect of Impurity in CO2 Streams on the Storage Capacity and the Plume Migration in Pohang Basin, Korea

NASA Astrophysics Data System (ADS)

Park, Yongchan; Choi, Byoungyoung; Shinn, Youngjae

2015-04-01

Captured CO2 streams contain various levels of impurities which vary depending on the combustion technology and CO2 sources such as a power plant and iron and steel production processes. Common impurities or contaminants are non-condensable gases like nitrogen, oxygen and hydrogen, and are also air pollutants like sulphur and nitrogen oxides. Specifically for geological storage, the non-condensable gases in CO2 streams are not favourable because they can decrease density of the injected CO2 stream and can affect buoyancy of the plume. However, separation of these impurities to obtain the CO2 purity higher than 99% would greatly increase the cost of capture. In 2010, the Korean Government announced a national framework to develop CCS, with the aim of developing two large scale integrated CCS projects by 2020. In order to achieve this goal, a small scale injection project into Pohang basin near shoreline has begun which is seeking the connection with a capture project, especially at a steel company. Any onshore sites that are suitable for the geological storage are not identified by this time so we turned to the shallow offshore Pohang basin where is close to a large-scale CO2 source. Currently, detailed site surveys are being undertaken and the collected data were used to establish a geological model of the basin. In this study, we performed preliminary modelling study on the effect of impurities on the geological storage using the geological model. Using a potential compositions of impurities in CO2 streams from the steel company, we firstly calculated density and viscosity of CO2 streams as a function of various pressure and temperature conditions with CMG-WINPROP and then investigated the effect of the non-condensable gases on storage capacity, injectivity and plume migrations with CMG-GEM. Further simulations to evaluate the areal and vertical sweep efficiencies by impurities were perform in a 2D vertical cross section as well as in a 3D simulation grid. Also, pressure increases caused by the impurities and the partitioning between CO2 and other non-condensable gases were explored. In addition, the possibility of using these contaminants as a tracer were examined.

Genetic approach to reconstruct complex regional geological setting of the Baltic basin in 3D geological model

NASA Astrophysics Data System (ADS)

Popovs, K.; Saks, T.; Ukass, J.; Jatnieks, J.

2012-04-01

Interpretation of geological structures in 3D geological models is a relatively new research topic that is already standardized in many geological branches. Due to its wide practical application, these models are indispensable and become one of the dominant interpretation methods in reducing geological uncertainties in many geology fields. Traditionally, geological concepts complement quantitative as much as qualitative data to obtain a model deemed acceptable, however, available data very often is insufficient and modeling methods primarily focus on spatial data but geological history usually is mostly neglected for the modeling of large sedimentary basins. A need to better integrate the long and often complex geological history and geological knowledge into modeling procedure is very acute to gain geological insight and improve the quality of geological models. During this research, 3D geological model of the Baltic basin (BB) was created. Because of its complex regional geological setting - wide range of the data sources with multiple scales, resolution and density as well as its various source formats, the study area provides a challenge for the 3D geological modeling. In order to create 3D regional geometrical model for the study area algorithmic genetic approach for model geometry reconstruction was applied. The genetic approach is based on the assumption that post-depositional deformation produce no significant change in sedimentary strata volume, assuming that the strata thickness and its length in a cross sectional plane remains unchanged except as a result of erosion. Assuming that the tectonic deformation occurred in sequential cycles and subsequent tectonic stage strata is separated by regional unconformity as is the case of the BB, there is an opportunity for algorithmic approach in reconstructing these conditions by sequentially reconstructing the layer original thickness. Layer thicknesses were sliced along fault lines, where applicable layer thickness was adjusted by taking into account amount of erosion by the presence of the regional unconformities. Borehole data and structural maps of some surfaces were used in creating geological model of the BB. Used approach allowed creating geologically sound geometric model. At first borehole logs were used to reconstruct initial thicknesses of different strata in every tectonic stage, where topography of each strata was obtained sequentially summing thickness to the initial reference surface from structural maps. Thereby each layer reflects the topography and amount of slip along the fault of the overlying layer. Overlying tectonic cycle sequence is implemented into the model structure by using unconformity surface as an initial reference surface. Applied techniques made possible reliably reconstructing and predicting in areas of sparse data layer surface geometry, its thickness distribution and evaluating displacements along the fault planes. Overall results indicate that the used approach has a good potential in development of regional geological models for the sedimentary basins and is valid for spatial interpretation of geological structures, subordinating this process to geological evolution prerequisites. This study is supported by the European Social Fund project No. 2009/0212/1DP/1.1.1.2.0/09/APIA/VIAA/060.

A recipe for consistent 3D management of velocity data and time-depth conversion using Vel-IO 3D

NASA Astrophysics Data System (ADS)

Maesano, Francesco E.; D'Ambrogi, Chiara

2017-04-01

3D geological model production and related basin analyses need large and consistent seismic dataset and hopefully well logs to support correlation and calibration; the workflow and tools used to manage and integrate different type of data control the soundness of the final 3D model. Even though seismic interpretation is a basic early step in such workflow, the most critical step to obtain a comprehensive 3D model useful for further analyses is represented by the construction of an effective 3D velocity model and a well constrained time-depth conversion. We present a complex workflow that includes comprehensive management of large seismic dataset and velocity data, the construction of a 3D instantaneous multilayer-cake velocity model, the time-depth conversion of highly heterogeneous geological framework, including both depositional and structural complexities. The core of the workflow is the construction of the 3D velocity model using Vel-IO 3D tool (Maesano and D'Ambrogi, 2017; https://github.com/framae80/Vel-IO3D) that is composed by the following three scripts, written in Python 2.7.11 under ArcGIS ArcPy environment: i) the 3D instantaneous velocity model builder creates a preliminary 3D instantaneous velocity model using key horizons in time domain and velocity data obtained from the analysis of well and pseudo-well logs. The script applies spatial interpolation to the velocity parameters and calculates the value of depth of each point on each horizon bounding the layer-cake velocity model. ii) the velocity model optimizer improves the consistency of the velocity model by adding new velocity data indirectly derived from measured depths, thus reducing the geometrical uncertainties in the areas located far from the original velocity data. iii) the time-depth converter runs the time-depth conversion of any object located inside the 3D velocity model The Vel-IO 3D tool allows one to create 3D geological models consistent with the primary geological constraints (e.g. depth of the markers on wells). The workflow and Vel-IO 3D tool have been developed and tested for the construction of the 3D geological model of a flat region, 5700 km2 in area, located in the central part of the Po Plain (Northern Italy) in the frame of the European funded Project GeoMol. The study area was covered by a dense dataset of seismic lines (ca. 12000 km) and exploration wells (130 drilling), mainly deriving from oil and gas exploration activities. The interpretation of the seismic dataset leads to the construction of a 3D model in time domain that has been depth converted using Vel-IO 3D, with a 4 layer-cake 3D instantaneous velocity model. The resulting final 3D geological model, composed of 15 horizons and 150 faults, has been used for basin analysis at regional scale, for geothermal assessment, and for the update of the seismotectonic knowledge of the Po Plain. The Vel-IO 3D has been further used for the depth conversion of the accretionary prism of the Calabrian subduction (Southern Italy) and for a basin scale analysis of the Po Plain Plio-Pleistocene evolution. Maesano F.E. and D'Ambrogi C., (2017), Computers and Geosciences, doi: 10.1016/j.cageo.2016.11.013 Vel-IO 3D is available at: https://github.com/framae80/Vel-IO3D

A retrospective streamflow ensemble forecast for an extreme hydrologic event: a case study of Hurricane Irene and on the Hudson River basin

NASA Astrophysics Data System (ADS)

Saleh, Firas; Ramaswamy, Venkatsundar; Georgas, Nickitas; Blumberg, Alan F.; Pullen, Julie

2016-07-01

This paper investigates the uncertainties in hourly streamflow ensemble forecasts for an extreme hydrological event using a hydrological model forced with short-range ensemble weather prediction models. A state-of-the art, automated, short-term hydrologic prediction framework was implemented using GIS and a regional scale hydrological model (HEC-HMS). The hydrologic framework was applied to the Hudson River basin ( ˜ 36 000 km2) in the United States using gridded precipitation data from the National Centers for Environmental Prediction (NCEP) North American Regional Reanalysis (NARR) and was validated against streamflow observations from the United States Geologic Survey (USGS). Finally, 21 precipitation ensemble members of the latest Global Ensemble Forecast System (GEFS/R) were forced into HEC-HMS to generate a retrospective streamflow ensemble forecast for an extreme hydrological event, Hurricane Irene. The work shows that ensemble stream discharge forecasts provide improved predictions and useful information about associated uncertainties, thus improving the assessment of risks when compared with deterministic forecasts. The uncertainties in weather inputs may result in false warnings and missed river flooding events, reducing the potential to effectively mitigate flood damage. The findings demonstrate how errors in the ensemble median streamflow forecast and time of peak, as well as the ensemble spread (uncertainty) are reduced 48 h pre-event by utilizing the ensemble framework. The methodology and implications of this work benefit efforts of short-term streamflow forecasts at regional scales, notably regarding the peak timing of an extreme hydrologic event when combined with a flood threshold exceedance diagram. Although the modeling framework was implemented on the Hudson River basin, it is flexible and applicable in other parts of the world where atmospheric reanalysis products and streamflow data are available.

Understanding the relationship between audiomagnetotelluric data and models, and borehole data in a hydrological environment

USGS Publications Warehouse

McPhee, D.K.; Pellerin, L.

2008-01-01

Audiomagnetotelluric (AMT) data and resulting models are analyzed with respect to geophysical and geological borehole logs in order to clarify the relationship between the two methodologies of investigation of a hydrological environment. Several profiles of AMT data collected in basins in southwestern United States are being used for groundwater exploration and hydrogeological framework studies. In a systematic manner, the AMT data and models are compared to borehole data by computing the equivalent one-dimensional AMT model and comparing with the two-dimensional (2-D) inverse AMT model. The spatial length is used to determine if the well is near enough to the AMT profile to quantify the relationship between the two datasets, and determine the required resolution of the AMT data and models. The significance of the quality of the borehole data when compared to the AMT data is also examined.

Analyzing risks to protected areas using the human modification framework: a Colorado case study

Treesearch

David M. Theobald; Alisa Wade; Grant Wilcox; Nate Peterson

2010-01-01

A framework that organizes natural and protected areas is often used to help understand the potential risks to natural areas and aspects of their ecological and human dimensions. The spatial (or landscape) context of these dynamics is also a critical, but, rarely considered, factor. Common classification systems include the U.S. Geological (USGS) Gap Analysis Program...

SHUTTLE IMAGING RADAR PROVIDES FRAMEWORK FOR SUBSURFACE GEOLOGIC EXPLORATION IN EGYPT AND SUDAN.

USGS Publications Warehouse

Breed, Carol S.; McCauley, John F.; Schaber, Gerald G.

1984-01-01

Shuttle Imaging Radar provides a pictorial framework to guide exploration for mineral resources (potential placers), groundwater sources, and prehistoric archaeological sites in the Western Desert of Egypt and Sudan. Documented penetration by the SIR-A signal of dry surficial sediment to depths of a meter or more revealed bedrock geologic features and networks of former stream valleys otherwise concealed beneath windblown sand, alluvium, and colluvial deposits. 'Radar units' mapped on SIR-A images according to relative brightness and degree of mottling correspond to subsurface geologic and topographic features identified in more than 50 test pits. Petrologic examination of pit samples confirms that a variety of depositional environments existed in this now hyper-arid region before it was mantled by windblown sand sheets and dunes. Wet sand was discovered in two buried valleys shown on the radar images and located in the field with the aid of co-registered maps and Landsat images, and a satellite navigation device. Buried valleys whose streams once traversed mineralized zones are potential sites of placers (gold, tin).

Database for the geologic map of the Mount Baker 30- by 60-minute quadrangle, Washington (I-2660)

USGS Publications Warehouse

Tabor, R.W.; Haugerud, R.A.; Hildreth, Wes; Brown, E.H.

2006-01-01

This digital map database has been prepared by R.W. Tabor from the published Geologic map of the Mount Baker 30- by 60-Minute Quadrangle, Washington. Together with the accompanying text files as PDF, it provides information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The authors mapped most of the geology at 1:100,000. The Quaternary contacts and structural data have been much simplified for the 1:100,000-scale map and database. The spatial resolution (scale) of the database is 1:100,000 or smaller. This database depicts the distribution of geologic materials and structures at a regional (1:100,000) scale. The report is intended to provide geologic information for the regional study of materials properties, earthquake shaking, landslide potential, mineral hazards, seismic velocity, and earthquake faults. In addition, the report contains information and interpretations about the regional geologic history and framework. However, the regional scale of this report does not provide sufficient detail for site development purposes.

Database for the geologic map of the Chelan 30-minute by 60-minute quadrangle, Washington (I-1661)

USGS Publications Warehouse

Tabor, R.W.; Frizzell, V.A.; Whetten, J.T.; Waitt, R.B.; Swanson, D.A.; Byerly, G.R.; Booth, D.B.; Hetherington, M.J.; Zartman, R.E.

2006-01-01

This digital map database has been prepared by R. W. Tabor from the published Geologic map of the Chelan 30-Minute Quadrangle, Washington. Together with the accompanying text files as PDF, it provides information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The authors mapped most of the bedrock geology at 1:100,000 scale, but compiled Quaternary units at 1:24,000 scale. The Quaternary contacts and structural data have been much simplified for the 1:100,000-scale map and database. The spatial resolution (scale) of the database is 1:100,000 or smaller. This database depicts the distribution of geologic materials and structures at a regional (1:100,000) scale. The report is intended to provide geologic information for the regional study of materials properties, earthquake shaking, landslide potential, mineral hazards, seismic velocity, and earthquake faults. In addition, the report contains information and interpretations about the regional geologic history and framework. However, the regional scale of this report does not provide sufficient detail for site development purposes.

Database for the geologic map of the Snoqualmie Pass 30-minute by 60-minute quadrangle, Washington (I-2538)

USGS Publications Warehouse

Tabor, R.W.; Frizzell, V.A.; Booth, D.B.; Waitt, R.B.

2006-01-01

This digital map database has been prepared by R.W. Tabor from the published Geologic map of the Snoqualmie Pass 30' X 60' Quadrangle, Washington. Together with the accompanying text files as PDF, it provides information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The authors mapped most of the bedrock geology at 1:100,000 scale, but compiled Quaternary units at 1:24,000 scale. The Quaternary contacts and structural data have been much simplified for the 1:100,000-scale map and database. The spatial resolution (scale) of the database is 1:100,000 or smaller. This database depicts the distribution of geologic materials and structures at a regional (1:100,000) scale. The report is intended to provide geologic information for the regional study of materials properties, earthquake shaking, landslide potential, mineral hazards, seismic velocity, and earthquake faults. In addition, the report contains information and interpretations about the regional geologic history and framework. However, the regional scale of this report does not provide sufficient detail for site development purposes.

Geologic Map of the Wenatchee 1:100,000 Quadrangle, Central Washington: A Digital Database

USGS Publications Warehouse

Tabor, R.W.; Waitt, R.B.; Frizzell, V.A.; Swanson, D.A.; Byerly, G.R.; Bentley, R.D.

2005-01-01

This digital map database has been prepared by R.W. Tabor from the published Geologic map of the Wenatchee 1:100,000 Quadrangle, Central Washington. Together with the accompanying text files as PDF, it provides information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The authors mapped most of the bedrock geology at 1:100,000 scale, but compiled Quaternary units at 1:24,000 scale. The Quaternary contacts and structural data have been much simplified for the 1:100,000-scale map and database. The spatial resolution (scale) of the database is 1:100,000 or smaller. This database depicts the distribution of geologic materials and structures at a regional (1:100,000) scale. The report is intended to provide geologic information for the regional study of materials properties, earthquake shaking, landslide potential, mineral hazards, seismic velocity, and earthquake faults. In addition, the report contains information and interpretations about the regional geologic history and framework. However, the regional scale of this report does not provide sufficient detail for site development purposes.

Internet-based information system of digital geological data providing

NASA Astrophysics Data System (ADS)

Yuon, Egor; Soukhanov, Mikhail; Markov, Kirill

2015-04-01

One of the Russian Federal аgency of mineral resources problems is to provide the geological information which was delivered during the field operation for the means of federal budget. This information should be present in the current, conditional form. Before, the leading way of presenting geological information were paper geological maps, slices, borehole diagrams reports etc. Technologies of database construction, including distributed databases, technologies of construction of distributed information-analytical systems and Internet-technologies are intensively developing nowadays. Most of geological organizations create their own information systems without any possibility of integration into other systems of the same orientation. In 2012, specialists of VNIIgeosystem together with specialists of VSEGEI started the large project - creating the system of providing digital geological materials with using modern and perspective internet-technologies. The system is based on the web-server and the set of special programs, which allows users to efficiently get rasterized and vectorised geological materials. These materials are: geological maps of scale 1:1M, geological maps of scale 1:200 000 and 1:2 500 000, the fragments of seamless geological 1:1M maps, structural zoning maps inside the seamless fragments, the legends for State geological maps 1:200 000 and 1:1 000 000, full author's set of maps and also current materials for international projects «Atlas of geological maps for Circumpolar Arctic scale 1:5 000 000» and «Atlas of Geologic maps of central Asia and adjacent areas scale 1:2 500 000». The most interesting and functional block of the system - is the block of providing structured and well-formalized geological vector materials, based on Gosgeolkart database (NGKIS), managed by Oracle and the Internet-access is supported by web-subsystem NGKIS, which is currently based on MGS-Framework platform, developed by VNIIgeosystem. One of the leading elements is the web-service, which realizes the interaction of all parts of the system and controls whole the way of the request from the user to the database and back, adopted to the GeoSciML and EarthResourceML view. The experience of creation the Internet-based information system of digital geological data providing, and also previous works, including the developing of web-service of NGKIS-system, allows to tell, that technological realization of presenting Russian geological-cartographical data with using of international standards is possible. While realizing, it could be some difficulties, associated with geological material depth. Russian informational geological model is more deep and wide, than foreign. This means the main problem of using international standards and formats: Russian geological data presentation is possible only with decreasing the data detalisation. But, such a problem becomes not very important, if the service publishes also Russian vocabularies, not associated with international vocabularies. In this case, the international format could be the interchange format to change data between Russian users. The integration into the international projects reaches developing of the correlation schemes between Russian and foreign classificators and vocabularies.

Mineral Resources | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

and geophysical framework of Alaska as it pertains to the mineral resources of the state. Summary maps and reports illustrate the geology of the state's prospective mineral terranes and provide data on the location, type, and potential of the state's mineral resources. These data aid in the state's management of

Modeling reactive transport processes in fractured rock using the time domain random walk approach within a dual-porosity framework

NASA Astrophysics Data System (ADS)

Roubinet, D.; Russian, A.; Dentz, M.; Gouze, P.

2017-12-01

Characterizing and modeling hydrodynamic reactive transport in fractured rock are critical challenges for various research fields and applications including environmental remediation, geological storage, and energy production. To this end, we consider a recently developed time domain random walk (TDRW) approach, which is adapted to reproduce anomalous transport behaviors and capture heterogeneous structural and physical properties. This method is also very well suited to optimize numerical simulations by memory-shared massive parallelization and provide numerical results at various scales. So far, the TDRW approach has been applied for modeling advective-diffusive transport with mass transfer between mobile and immobile regions and simple (theoretical) reactions in heterogeneous porous media represented as single continuum domains. We extend this approach to dual-continuum representations considering a highly permeable fracture network embedded into a poorly permeable rock matrix with heterogeneous geochemical reactions occurring in both geological structures. The resulting numerical model enables us to extend the range of the modeled heterogeneity scales with an accurate representation of solute transport processes and no assumption on the Fickianity of these processes. The proposed model is compared to existing particle-based methods that are usually used to model reactive transport in fractured rocks assuming a homogeneous surrounding matrix, and is used to evaluate the impact of the matrix heterogeneity on the apparent reaction rates for different 2D and 3D simple-to-complex fracture network configurations.

MISSISSIPPI EMBAYMENT AQUIFER SYSTEM IN MISSISSIPPI: GEOHYDROLOGIC DATA COMPILATION FOR FLOW MODEL SIMULATION.

USGS Publications Warehouse

Arthur, J.K.; Taylor, R.E.

1986-01-01

As part of the Gulf Coast Regional Aquifer System Analysis (GC RASA) study, data from 184 geophysical well logs were used to define the geohydrologic framework of the Mississippi embayment aquifer system in Mississippi for flow model simulation. Five major aquifers of Eocene and Paleocene age were defined within this aquifer system in Mississippi. A computer data storage system was established to assimilate the information obtained from the geophysical logs. Computer programs were developed to manipulate the data to construct geologic sections and structure maps. Data from the storage system will be input to a five-layer, three-dimensional, finite-difference digital computer model that is used to simulate the flow dynamics in the five major aquifers of the Mississippi embayment aquifer system.

Waste IPSC : Thermal-Hydrologic-Chemical-Mechanical (THCM) modeling and simulation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Freeze, Geoffrey A.; Wang, Yifeng; Arguello, Jose Guadalupe, Jr.

2010-10-01

Waste IPSC Objective is to develop an integrated suite of high performance computing capabilities to simulate radionuclide movement through the engineered components and geosphere of a radioactive waste storage or disposal system: (1) with robust thermal-hydrologic-chemical-mechanical (THCM) coupling; (2) for a range of disposal system alternatives (concepts, waste form types, engineered designs, geologic settings); (3) for long time scales and associated large uncertainties; (4) at multiple model fidelities (sub-continuum, high-fidelity continuum, PA); and (5) in accordance with V&V and software quality requirements. THCM Modeling collaborates with: (1) Other Waste IPSC activities: Sub-Continuum Processes (and FMM), Frameworks and Infrastructure (and VU,more » ECT, and CT); (2) Waste Form Campaign; (3) Used Fuel Disposition (UFD) Campaign; and (4) ASCEM.« less

A Global Geologic Map of Europa

NASA Astrophysics Data System (ADS)

Janelle Leonard, Erin; Patthoff, Donald Alex; Senske, David A.; Collins, Geoffrey

2017-10-01

Understanding the global scale geology of Europa is paramount to gaining insight into the potential habitability of this icy world. To this end, work is ongoing to complete a global geological map at the scale of 1:15 million that incorporates data at all resolutions collected by the Voyager and Galileo missions. The results of this work will aid the Europa Clipper mission, now in formulation, by providing a framework for collaborative and synergistic science investigations.To understand global geologic and tectonic relations, a total of 10 geologic units have been defined. These include: Low Albedo Ridge Material (lam)—low albedo material that irregularly surrounds large (>20 km) ridge structures; Ridged plains (pr)—distributed over all latitudes and characterized by subparallel to cross-cutting ridges and troughs visible at high resolution (<100 m/px); Band material (b)—linear to curvilinear zones with a distinct, abrupt albedo change from the surrounding region; Crater material (c), Continuous Crater Ejecta (ce) and Discontinuous Crater Ejecta (dce)—features associated with impact craters including the site of the impact, crater material, and the fall-out debris respectively; Low Albedo Chaos (chl), Mottled Albedo Chaos (chm) and High Albedo Chaos (chh)—disrupted terrain with a relatively uniform low albedo, patchy/variegated albedo, and uniform high albedo appearance respectively; Knobby Chaos (chk) - disrupted terrain with rough and blocky texture occurring in the high latitudes.In addition to the geologic units, our mapping also includes structural features—Ridges, Cycloids, Undifferentiated Linea, Crater Rims, Depression Margins, Dome Margins and Troughs. We also introduce a point feature (at the global scale), Microchaos, to denote small (<10 km) patches of discontinuous chaos material. The completed map will constrain the distribution of different Europa terrains and provide a general stratigraphic framework to assess the geologic history of Europa from the regional to the global scale.

The First USGS Global Geologic Map of Europa

NASA Astrophysics Data System (ADS)

Leonard, E. J.; Patthoff, D. A.; Senske, D.; Collins, G. C.

2017-12-01

Understanding the global scale geology of Europa is paramount to gaining insight into the potential habitability of this icy world. To this end, work is ongoing to complete a global geological map at the scale of 1:15 million that incorporates data at all resolutions collected by the Voyager and Galileo missions. The results of this work will aid the Europa Clipper mission, now in formulation, by providing a framework for collaborative and synergistic science investigations. To understand global geologic and tectonic relations, a total of 10 geologic units have been defined. These include: Low Albedo Ridge Material (lam)—low albedo material that irregularly surrounds large (>20 km) ridge structures; Ridged plains (pr)—distributed over all latitudes and characterized by subparallel to cross-cutting ridges and troughs visible at high resolution (<100 m/px); Band material (b)—linear to curvilinear zones with a distinct, abrupt albedo change from the surrounding region; Crater material (c), Continuous Crater Ejecta (ce) and Discontinuous Crater Ejecta (dce)—features associated with impact craters including the site of the impact, crater material, and the fall-out debris respectively; Low Albedo Chaos (chl), Mottled Albedo Chaos (chm) and High Albedo Chaos (chh)—disrupted terrain with a relatively uniform low albedo, patchy/variegated albedo, and uniform high albedo appearance respectively; Knobby Chaos (chk) - disrupted terrain with rough and blocky texture occurring in the high latitudes. In addition to the geologic units, our mapping also includes structural features—Ridges, Cycloids, Undifferentiated Linea, Crater Rims, Depression Margins, Dome Margins and Troughs. We also introduce a point feature (at the global scale), Microchaos, to denote small (<10 km) patches of discontinuous chaos material. The completed map will constrain the distribution of different Europa terrains and provide a general stratigraphic framework to assess the geologic history of Europa from the regional to the global scale. Here, we present the map submitted to the USGS for review.

Compiling a national resistivity atlas of Denmark based on airborne and ground-based transient electromagnetic data

NASA Astrophysics Data System (ADS)

Barfod, Adrian A. S.; Møller, Ingelise; Christiansen, Anders V.

2016-11-01

We present a large-scale study of the petrophysical relationship of resistivities obtained from densely sampled ground-based and airborne transient electromagnetic surveys and lithological information from boreholes. The overriding aim of this study is to develop a framework for examining the resistivity-lithology relationship in a statistical manner and apply this framework to gain a better description of the large-scale resistivity structures of the subsurface. In Denmark very large and extensive datasets are available through the national geophysical and borehole databases, GERDA and JUPITER respectively. In a 10 by 10 km grid, these data are compiled into histograms of resistivity versus lithology. To do this, the geophysical data are interpolated to the position of the boreholes, which allows for a lithological categorization of the interpolated resistivity values, yielding different histograms for a set of desired lithological categories. By applying the proposed algorithm to all available boreholes and airborne and ground-based transient electromagnetic data we build nation-wide maps of the resistivity-lithology relationships in Denmark. The presented Resistivity Atlas reveals varying patterns in the large-scale resistivity-lithology relations, reflecting geological details such as available source material for tills. The resistivity maps also reveal a clear ambiguity in the resistivity values for different lithologies. The Resistivity Atlas is highly useful when geophysical data are to be used for geological or hydrological modeling.

2013 strategic petroleum reserve big hill well integrity grading report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lord, David L.; Roberts, Barry L.; Lord, Anna C. Snider

2014-02-01

This report summarizes the work performed in developing a framework for the prioritization of cavern access wells for remediation and monitoring at the Big Hill Strategic Petroleum Reserve site. This framework was then applied to all 28 wells at the Big Hill site with each well receiving a grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading framework including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The framework was developed in a way as to be applicable to all four of the Strategic Petroleum Reserve sites.

Stratigraphic framework of Cambrian and Ordovician rocks in the central Appalachian basin from Medina County, Ohio, through southwestern and south-central Pennsylvania to Hampshire County, West Virginia: Chapter E.2.2 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ryder, Robert T.; Harris, Anita G.; Repetski, John E.; Crangle, Robert D.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

This chapter is a re-release of U.S. Geological Survey Bulletin 1839-K, of the same title, by Ryder and others (1992; online version 2.0 revised and digitized by Robert D. Crangle, Jr., 2003). It consists of one file of the report text as it appeared in USGS Bulletin 1839-K and a second file containing the cross section, figures 1 and 2, and tables 1 and 2 on one oversized sheet; the second file was digitized in 2003 as version 2.0 and also includes the gamma-ray well log traces.

Description of the U.S. Geological Survey Geo Data Portal data integration framework

USGS Publications Warehouse

Blodgett, David L.; Booth, Nathaniel L.; Kunicki, Thomas C.; Walker, Jordan I.; Lucido, Jessica M.

2012-01-01

The U.S. Geological Survey has developed an open-standard data integration framework for working efficiently and effectively with large collections of climate and other geoscience data. A web interface accesses catalog datasets to find data services. Data resources can then be rendered for mapping and dataset metadata are derived directly from these web services. Algorithm configuration and information needed to retrieve data for processing are passed to a server where all large-volume data access and manipulation takes place. The data integration strategy described here was implemented by leveraging existing free and open source software. Details of the software used are omitted; rather, emphasis is placed on how open-standard web services and data encodings can be used in an architecture that integrates common geographic and atmospheric data.

Bedrock Geologic Map of the Greater Lefkosia Area, Cyprus

USGS Publications Warehouse

Harrison, Richard W.; Newell, Wayne L.; Panayides, Ioannis; Stone, Byron; Tsiolakis, Efthymios; Necdet, Mehmet; Batihanli, Hilmi; Ozhur, Ayse; Lord, Alan; Berksoy, Okan; Zomeni, Zomenia; Schindler, J. Stephen

2008-01-01

The island of Cyprus has a long historical record of earthquakes that have damaged pre-Roman to modern human settlements. Because the recurrent damaging earthquakes can have a significant economic and social impact on Cyprus, this project was initiated to develop a seismic-hazard assessment for a roughly 400 square kilometer area centered on Cyprus' capital and largest city, whose European name is Nicosia and whose local name is Lefkosia. In addition, geologic and seismotectonic evaluations for the project extended beyond the perimeter of the geologic map. Additional structural, stratigraphic, and paleontological data were collected island-wide as well as data from literature research throughout the eastern Mediterranean region, in order to accurately place the geology and seismic hazards of the Lefkosia area in a regional tectonic framework.

Geologic map of the southern White Ledge Peak and Matilija quadrangles, Santa Barbara and Ventura Counties, California

USGS Publications Warehouse

Minor, Scott A.; Brandt, Theodore R.

2015-01-01

A principal aim of the new mapping and associated fault-kinematic measurements is to document and constrain the nature of transpressional strain transfer between various regional, potentially seismogenic faults. In the accompanying pamphlet, surficial and bedrock map units are described in detail as well as a summary of the structural and fault-kinematic framework of the map area. New biostratigraphic and biochronologic data based on microfossil identifications are presented in expanded unit descriptions of the marine Neogene Monterey and Sisquoc Formations. Site-specific fault kinematic observations are embedded in the digital map database. This compilation provides a uniform geologic digital geodatabase and map plot files that can be used for visualization, analysis, and interpretation of the area’s geology, geologic hazards, and natural resources.

Hydrogeologic unit flow characterization using transition probability geostatistics.

PubMed

Jones, Norman L; Walker, Justin R; Carle, Steven F

2005-01-01

This paper describes a technique for applying the transition probability geostatistics method for stochastic simulation to a MODFLOW model. Transition probability geostatistics has some advantages over traditional indicator kriging methods including a simpler and more intuitive framework for interpreting geologic relationships and the ability to simulate juxtapositional tendencies such as fining upward sequences. The indicator arrays generated by the transition probability simulation are converted to layer elevation and thickness arrays for use with the new Hydrogeologic Unit Flow package in MODFLOW 2000. This makes it possible to preserve complex heterogeneity while using reasonably sized grids and/or grids with nonuniform cell thicknesses.

Magnetotelluric data collected to characterize aquifers in the San Luis Basin, New Mexico

USGS Publications Warehouse

Ailes, Chad E.; Rodriguez, Brian D.

2015-01-01

The U.S. Geological Survey is conducting a series of multidisciplinary studies of the San Luis Basin as part of the Geologic Framework of Rio Grande Basins project. Detailed geologic mapping, high-resolution airborne magnetic surveys, gravity surveys, magnetotelluric surveys, and hydrologic and lithologic data are being used to better understand the aquifers in the San Luis Basin. This report describes one north-south and two east-west regional magnetotelluric sounding profiles, acquired in June of 2010 and July and August of 2011, across the San Luis Basin in northern New Mexico. No interpretation of the data is included.

A risk assessment tool applied to the study of shale gas resources.

PubMed

Veiguela, Miguel; Hurtado, Antonio; Eguilior, Sonsoles; Recreo, Fernando; Roqueñi, Nieves; Loredo, Jorge

2016-11-15

The implementation of a risk assessment tool with the capacity to evaluate the risks for health, safety and the environment (HSE) from extraction of non-conventional fossil fuel resources by the hydraulic fracturing (fracking) technique can be a useful tool to boost development and progress of the technology and winning public trust and acceptance of this. At the early project stages, the lack of data related the selection of non-conventional gas deposits makes it difficult the use of existing approaches to risk assessment of fluids injected into geologic formations. The qualitative risk assessment tool developed in this work is based on the approach that shale gas exploitation risk is dependent on both the geologic site and the technological aspects. It follows from the Oldenburg's 'Screening and Ranking Framework (SRF)' developed to evaluate potential geologic carbon dioxide (CO2) storage sites. These two global characteristics: (1) characteristics centered on the natural aspects of the site and (2) characteristics centered on the technological aspects of the Project, have been evaluated through user input of Property values, which define Attributes, which define the Characteristics. In order to carry out an individual evaluation of each of the characteristics and the elements of the model, the tool has been implemented in a spreadsheet. The proposed model has been applied to a site with potential for the exploitation of shale gas in Asturias (northwestern Spain) with tree different technological options to test the approach. Copyright © 2016 Elsevier B.V. All rights reserved.

Audiomagnetotelluric Data and Preliminary Two-Dimensional Models from Spring, Dry Lake, and Delamar Valleys, Nevada

USGS Publications Warehouse

McPhee, Darcy K.; Chuchel, Bruce A.; Pellerin, Louise

2008-01-01

This report presents audiomagnetotelluric (AMT) data along fourteen profiles in Spring, Delamar, and Dry Lake Valleys, and the corresponding preliminary two-dimensional (2-D) inverse models. The AMT method is a valuable tool for estimating the electrical resistivity of the Earth over depth ranges from a few meters to less than one kilometer, and it is important for revealing subsurface structure and stratigraphy within the Basin and Range province of eastern Nevada, which can be used to define the geohydrologic framework of the region. We collected AMT data by using the Geometrics StrataGem EH4 system. Profiles were 0.7 - 3.2 km in length with station spacing of 50-400 m. Data were recorded in a coordinate system parallel to and perpendicular to the regional geologic-strike direction with Z positive down. We show AMT station locations, sounding curves of apparent resistivity, phase, and coherency, and 2-D models of subsurface resistivity along the profiles. The 2-D inverse models are computed from the transverse electric (TE), transverse magnetic (TM), and TE+TM mode data by using a conjugate gradient, finite-difference method. Preliminary interpretation of the 2-D models defines the structural framework of the basins and the resistivity contrasts between alluvial basin-fill, volcanic units, and carbonate basement rocks.

A Local to National Scale Catchment Model Simulation Framework for Hydrological Predictions and Impact Assessments Under Uncertainty

NASA Astrophysics Data System (ADS)

Freer, Jim; Coxon, Gemma; Quinn, Niall; Dunne, Toby; Lane, Rosie; Bates, Paul; Wagener, Thorsten; Woods, Ross; Neal, Jeff; Howden, Nicholas; Musuuza, Jude

2017-04-01

There is a huge challenge in developing hydrological model structures that can be used for hypothesis testing, prediction, impact assessment and risk analyses over a wide range of spatial scales. There are many reasons why this is the case, from computational demands, to how we define and characterize different features and pathway connectivities in the landscape, that differ depending on the objectives of the study. However there is certainly a need more than ever to explore the trade-offs between the complexity of modelling applied (i.e. spatial discretization, levels of process representation, complexity of landscape representation) compared to the benefits realized in terms of predictive capability and robustness of these predictions during hydrological extremes and during change. Furthermore, there is a further balance, particularly associated with prediction uncertainties, in that it is not desirable to have modelling systems that are too complex compared to the observed data that would ever be available to apply them. This is particularly the case when models are applied to quantify national impact assessments, especially if these are based on validation assessments from smaller more detailed case studies. Therefore the hydrological community needs modelling tools and approaches that enable these trade-offs to be explored and to understand the level of representation needed in models to be 'fit-for-purpose' for a given application. This paper presents a catchment scale national modelling framework based on Dynamic-TOPMODEL specifically setup to fulfil these aims. A key component of the modelling framework is it's structural flexibility, as is the ability to assess model outputs using Monte Carlo simulation techniques. The model build has been automated to work at any spatial scale to the national scale, and within that to control the level of spatial discretisation and connectivity of locally accounted landscape elements in the form of hydrological response units (HRU's). This allows for the explicit consideration of spatial rainfall fields, landscape, soils and geological attributes and the spatial connectivity of hydrological flow pathways to explore what level of modelling complexity we need for different prediction problems. We shall present this framework and show how it can be used in flood and drought risk analyses as well as include attributes and features within the landscape to explore societal and climate impacts effectively within an uncertainty analyses framework.

Localized Smart-Interpretation

NASA Astrophysics Data System (ADS)

Lundh Gulbrandsen, Mats; Mejer Hansen, Thomas; Bach, Torben; Pallesen, Tom

2014-05-01

The complex task of setting up a geological model consists not only of combining available geological information into a conceptual plausible model, but also requires consistency with availably data, e.g. geophysical data. However, in many cases the direct geological information, e.g borehole samples, are very sparse, so in order to create a geological model, the geologist needs to rely on the geophysical data. The problem is however, that the amount of geophysical data in many cases are so vast that it is practically impossible to integrate all of them in the manual interpretation process. This means that a lot of the information available from the geophysical surveys are unexploited, which is a problem, due to the fact that the resulting geological model does not fulfill its full potential and hence are less trustworthy. We suggest an approach to geological modeling that 1. allow all geophysical data to be considered when building the geological model 2. is fast 3. allow quantification of geological modeling. The method is constructed to build a statistical model, f(d,m), describing the relation between what the geologists interpret, d, and what the geologist knows, m. The para- meter m reflects any available information that can be quantified, such as geophysical data, the result of a geophysical inversion, elevation maps, etc... The parameter d reflects an actual interpretation, such as for example the depth to the base of a ground water reservoir. First we infer a statistical model f(d,m), by examining sets of actual interpretations made by a geological expert, [d1, d2, ...], and the information used to perform the interpretation; [m1, m2, ...]. This makes it possible to quantify how the geological expert performs interpolation through f(d,m). As the geological expert proceeds interpreting, the number of interpreted datapoints from which the statistical model is inferred increases, and therefore the accuracy of the statistical model increases. When a model f(d,m) successfully has been inferred, we are able to simulate how the geological expert would perform an interpretation given some external information m, through f(d|m). We will demonstrate this method applied on geological interpretation and densely sampled airborne electromagnetic data. In short, our goal is to build a statistical model describing how a geological expert performs geological interpretation given some geophysical data. We then wish to use this statistical model to perform semi automatic interpretation, everywhere where such geophysical data exist, in a manner consistent with the choices made by a geological expert. Benefits of such a statistical model are that 1. it provides a quantification of how a geological expert performs interpretation based on available diverse data 2. all available geophysical information can be used 3. it allows much faster interpretation of large data sets.

Hydrostratigraphic Framework and Selection and Correlation of Geophysical Log Markers in the Surficial Aquifer System, Palm Beach County, Florida

USGS Publications Warehouse

Reese, Ronald S.; Wacker, Michael A.

2007-01-01

The surficial aquifer system is the major source of freshwater for public water supply in Palm Beach County, Florida, yet many previous studies of the hydrogeology of this aquifer system have focused only on the eastern one-half to one-third of the county in the more densely populated coastal area (Land and others, 1973; Swayze and others, 1980; Swayze and Miller, 1984; Shine and others, 1989). Population growth in the county has resulted in the westward expansion of urbanized areas into agricultural areas and has created new demands on the water resources of the county. Additionally, interest in surface-water resources of central and western areas of the county has increased. In these areas, plans for additional surface-water storage reservoirs are being made under the Comprehensive Everglades Restoration Plan originally proposed by the U.S. Army Corps of Engineers and the South Florida Water Management District (1999), and stormwater treatment areas have been constructed by the South Florida Water Management District. Surface-water and ground-water interactions in the Everglades are thought to be important to water budgets, water quality, and ecology (Harvey and others, 2002). Most of the previous hydrogeologic and ground-water flow simulation studies of the surficial aquifer system have not utilized a hydrostratigraphic framework, in which stratigraphic or sequence stratigraphic units, such as those proposed in Cunningham and others (2001), are delineated in this stratigraphically complex aquifer system. A thick zone of secondary permeability mapped by Swayze and Miller (1984) was not subdivided and was identified as only being within the Anastasia Formation of Pleistocene age. Miller (1987) published 11 geologic sections of the surficial aquifer system, but did not delineate any named stratigraphic units in these sections. This limited interpretation has resulted, in part, from the complex facies changes within rocks and sediments of the surficial aquifer system and the seemingly indistinct and repetitious nature of the most common lithologies, which include sand, shell, sandstone, and limestone. Model construction and layer definition in a simulation of ground-water flow within the surficial aquifer system of Palm Beach County utilized only the boundaries of one or two major hydrogeologic zones, such as the Biscayne aquifer and surficial aquifer system; otherwise layers were defined by average elevations rather than geologic structure or stratigraphy (Shine and others, 1989). Additionally, each major permeable zone layer in the model was assumed to have constant hydraulic conductivity with no allowance for the possibility of discrete (thin) flow zones within the zone. The key to understanding the spatial distribution and hydraulic connectivity of permeable zones in the surficial aquifer system beneath Palm Beach County is the development of a stratigraphic framework based on a consistent method of county-wide correlation. Variability in hydraulic properties in the system needs to be linked to the stratigraphic units delineated in this framework, and proper delineation of the hydrostratigraphic framework should provide a better understanding and simulation of the ground-water flow system. In 2004, the U.S. Geological Survey, in cooperation with the South Florida Water Management District, initiated an investigation to develop a hydrostratigraphic framework for the surficial aquifer system in Palm Beach County.

Teaching the geological subsurface with 3D models

NASA Astrophysics Data System (ADS)

Thorpe, Steve; Ward, Emma

2014-05-01

3D geological models have great potential as a resource when teaching geological concepts as it allows the student to visualise and interrogate UK geology. They are especially useful when dealing with the conversion of 2D field, map and GIS outputs into three dimensional geological units, which is a common problem for many students. Today's earth science students use a variety of skills and processes during their learning experience including spatial thinking, image construction, detecting patterns, making predictions and deducing the orientation of themselves. 3D geological models can reinforce spatial thinking strategies and encourage students to think about processes and properties, in turn helping the student to recognise pre-learnt geological principles in the field and to convert what they see at the surface into a picture of what is going on at depth. The British Geological Survey (BGS) has been producing digital 3D geological models for over 10 years. The models produced are revolutionising the working practices, data standards and products of the BGS. Sharing our geoscience information with academia is highlighted throughout the BGS strategy as is instilling practical skills in future geoscience professionals, such as model building and interpretation. In 2009 a project was launched to investigate the potential of the models as a teaching resource. The study included justifying if and how the models help students to learn, how models have been used historically, and how other forms of modelling are being used today. BGS now produce 3D geological models for use by anyone teaching or learning geoscience. They incorporate educational strategies that will develop geospatial skills and alleviate potential problems that some students experience. They are contained within contemporary case studies and show standard geological concepts, structures, sedimentary rocks, cross sections and field techniques. 3D geological models of the Isle of Wight and Ingleborough along with accompanying education material and a video tutorial guide are currently available to the public on our website www.bgs.ac.uk. 2014 will see the launch of a further 5-6 models, each illustrating different geological locations, rock types and complexities. This poster aims to show the methodology and techniques for generating a 3D geological model. It will provide background information on the project and how these models can be used as a teaching resource, either in a formal classroom setting or as a distance learning tool. The model allows the student to take part in virtual fieldwork, by viewing the landscape in association with the geological structures and processes that have shaped it.

Toward developing more realistic groundwater models using big data

NASA Astrophysics Data System (ADS)

Vahdat Aboueshagh, H.; Tsai, F. T. C.; Bhatta, D.; Paudel, K.

2017-12-01

Rich geological data is the backbone of developing realistic groundwater models for groundwater resources management. However, constructing realistic groundwater models can be challenging due to inconsistency between different sources of geological, hydrogeological and geophysical data and difficulty in processing big data to characterize the subsurface environment. This study develops a framework to utilize a big geological dataset to create a groundwater model for the Chicot Aquifer in the southwestern Louisiana, which borders on the Gulf of Mexico at south. The Chicot Aquifer is the principal source of fresh water in southwest Louisiana, underlying an area of about 9,000 square miles. Agriculture is the largest groundwater consumer in this region and overpumping has caused significant groundwater head decline and saltwater intrusion from the Gulf and deep formations. A hydrostratigraphy model was constructed using around 29,000 electrical logs and drillers' logs as well as screen lengths of pumping wells through a natural neighbor interpolation method. These sources of information have different weights in terms of accuracy and trustworthy. A data prioritization procedure was developed to filter untrustworthy log information, eliminate redundant data, and establish consensus of various lithological information. The constructed hydrostratigraphy model shows 40% sand facies, which is consistent with the well log data. The hydrostratigraphy model confirms outcrop areas of the Chicot Aquifer in the north of the study region. The aquifer sand formation is thinning eastward to merge into Atchafalaya River alluvial aquifer and coalesces to the underlying Evangeline aquifer. A grid generator was used to convert the hydrostratigraphy model into a MODFLOW grid with 57 layers. A Chicot groundwater model was constructed using the available hydrologic and hydrogeological data for 2004-2015. Pumping rates for irrigation wells were estimated using the crop type and acreage data from the USDACropScape. Groundwater level data obtained from the USGS were used to determine the model boundary and initial conditions. Recharge rates were approximated based on surficial lithology and rainfall data. The Chicot aquifer model will be used to understand groundwater availability in southwest Louisiana.

Planning and design of studies for river-quality assessment in the Truckee and Carson River basins, California and Nevada

USGS Publications Warehouse

Nowlin, Jon O.; Brown, W.M.; Smith, L.H.; Hoffman, R.J.

1980-01-01

The objectives of the Geological Survey 's river-quality assessment in the Truckee and Carson River basins in California and Nevada are to identify the significant resource management problems; to develop techniques to assess the problems; and to effectively communicate results to responsible managers. Six major elements of the assessment to be completed by October 1981 are (1) a detailing of the legal, institutional, and structural development of water resources in the basins and the current problems and conflicts; (2) a compilation and synthesis of the physical hydrology of the basins; (3) development of a special workshop approach to involve local management in the direction and results of the study; (4) development of a comprehensive streamflow model emcompassing both basins to provide a quantitative hydrologic framework for water-quality analysis; (5) development of a water-quality transport model for selected constituents and characteristics on selected reaches of the Truckee River; and (6) a detailed examination of selected fish habitats for specified reaches of the Truckee River. Progress will be periodically reported in reports, maps, computer data files, mathematical models, a bibliography, and public presentations. In building a basic framework to develop techniques, the basins were viewed as a single hydrologic unit because of interconnecting diversion structures. The framework comprises 13 hydrographic subunits to facilitate modeling and sampling. Several significant issues beyond the scope of the assessment were considered as supplementary proposals; water-quality loadings in Truckee and Carson Rivers, urban runoff in Reno and management alternatives, and a model of limnological processes in Lahontan Reservoir. (USGS)

CO2 Storage related Groundwater Impacts and Protection

NASA Astrophysics Data System (ADS)

Fischer, Sebastian; Knopf, Stefan; May, Franz; Rebscher, Dorothee

2016-03-01

Injection of CO2 into the deep subsurface will affect physical and chemical conditions in the storage environment. Hence, geological CO2 storage can have potential impacts on groundwater resources. Shallow freshwater can only be affected if leakage pathways facilitate the ascent of CO2 or saline formation water. Leakage associated with CO2 storage cannot be excluded, but potential environmental impacts could be reduced by selecting suitable storage locations. In the framework of risk assessment, testing of models and scenarios against operational data has to be performed repeatedly in order to predict the long-term fate of CO2. Monitoring of a storage site should reveal any deviations from expected storage performance, so that corrective measures can be taken. Comprehensive R & D activities and experience from several storage projects will enhance the state of knowledge on geological CO2 storage, thus enabling safe storage operations at well-characterised and carefully selected storage sites while meeting the requirements of groundwater protection.

Southern Alaska Coastal Relief Model

NASA Astrophysics Data System (ADS)

Lim, E.; Eakins, B.; Wigley, R.

2009-12-01

The National Geophysical Data Center (NGDC), an office of the National Oceanic and Atmospheric Administration (NOAA), in conjunction with the Cooperative Institute for Research in Environmental Sciences (CIRES) at the University of Colorado at Boulder, has developed a 24 arc-second integrated bathymetric-topographic digital elevation model of Southern Alaska. This Coastal Relief Model (CRM) was generated from diverse digital datasets that were obtained from NGDC, the United States Geological Survey, and other U.S. and international agencies. The CRM spans 170° to 230° E and 48.5° to 66.5° N, including the Gulf of Alaska, Bering Sea, Aleutian Islands, and Alaska’s largest communities: Anchorage, Fairbanks, and Juneau. The CRM provides a framework for enabling scientists to refine tsunami propagation and ocean circulation modeling through increased resolution of geomorphologic features. It may also be useful for benthic habitat research, weather forecasting, and environmental stewardship. Shaded-relief image of the Southern Alaska Coastal Relief Model.

Linking MODFLOW with an agent-based land-use model to support decision making

USGS Publications Warehouse

Reeves, H.W.; Zellner, M.L.

2010-01-01

The U.S. Geological Survey numerical groundwater flow model, MODFLOW, was integrated with an agent-based land-use model to yield a simulator for environmental planning studies. Ultimately, this integrated simulator will be used as a means to organize information, illustrate potential system responses, and facilitate communication within a participatory modeling framework. Initial results show the potential system response to different zoning policy scenarios in terms of the spatial patterns of development, which is referred to as urban form, and consequent impacts on groundwater levels. These results illustrate how the integrated simulator is capable of representing the complexity of the system. From a groundwater modeling perspective, the most important aspect of the integration is that the simulator generates stresses on the groundwater system within the simulation in contrast to the traditional approach that requires the user to specify the stresses through time. Copyright ?? 2010 The Author(s). Journal compilation ?? 2010 National Ground Water Association.

Geologic framework for the national assessment of carbon dioxide storage resources: Bighorn Basin, Wyoming and Montana: Chapter A in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Covault, Jacob A.; Buursink, Mark L.; Craddock, William H.; Merrill, Matthew D.; Blondes, Madalyn S.; Gosai, Mayur A.; Freeman, P.A.; Warwick, Peter D.; Corum, Margo D.

2012-01-01

This report identifies and contains geologic descriptions of twelve storage assessment units (SAUs) in six separate packages of sedimentary rocks within the Bighorn Basin of Wyoming and Montana and focuses on the particular characteristics, specified in the methodology, that influence the potential CO2 storage resource in those SAUs. Specific descriptions of the SAU boundaries as well as their sealing and reservoir units are included. Properties for each SAU such as depth to top, gross thickness, net porous thickness, porosity, permeability, groundwater quality, and structural reservoir traps are provided to illustrate geologic factors critical to the assessment. Although assessment results are not contained in this report, the geologic information included here will be employed, as specified in the methodology of earlier work, to calculate a statistical Monte Carlo-based distribution of potential storage space in the various SAUs. Figures in this report show SAU boundaries and cell maps of well penetrations through the sealing unit into the top of the storage formation. Wells sharing the same well borehole are treated as a single penetration. Cell maps show the number of penetrating wells within one square mile and are derived from interpretations of incompletely attributed well data, a digital compilation that is known not to include all drilling. The USGS does not expect to know the location of all wells and cannot guarantee the amount of drilling through specific formations in any given cell shown on cell maps.

Scale of human mobility in the southern Andes (Argentina and Chile): A new framework based on strontium isotopes.

PubMed

Barberena, Ramiro; Durán, Víctor A; Novellino, Paula; Winocur, Diego; Benítez, Anahí; Tessone, Augusto; Quiroga, María N; Marsh, Erik J; Gasco, Alejandra; Cortegoso, Valeria; Lucero, Gustavo; Llano, Carina; Knudson, Kelly J

2017-10-01

The goal of this article is to assess the scale of human paleomobility and ecological complementarity between the lowlands and highlands in the southern Andes during the last 2,300 years. By providing isotope results for human bone and teeth samples, we assess a hypothesis of "high residential mobility" suggested on the basis of oxygen isotopes from human remains. We develop an isotopic assessment of human mobility in a mountain landscape combining strontium and oxygen isotopes. We analyze bone and teeth samples as an approach to life-history changes in spatial residence. Human samples from the main geological units and periods within the last two millennia are selected. We present a framework for the analysis of bioavailable strontium based on the combination of the geological data with isotope results for rodent samples. The 87 Sr/ 86 Sr values from human samples indicate residential stability within geological regions along life history. When comparing strontium and oxygen values for the same human samples, we record a divergent pattern: while δ 18 O values for samples from distant regions overlap widely, there are important differences in 87 Sr/ 86 Sr values. Despite the large socio-economic changes recorded, 87 Sr/ 86 Sr values indicate a persisting scenario of low systematic mobility between the different geological regions. Our results suggest that strontium isotope values provide the most germane means to track patterns of human occupation of distinct regions in complex geological landscapes, offering a much higher spatial resolution than oxygen isotopes in the southern Andes. © 2017 Wiley Periodicals, Inc.

Developing Connectivist Schemas for Geological and Geomorphological Education

NASA Astrophysics Data System (ADS)

Whalley, B.

2012-12-01

Teaching geology is difficult; students need to grasp changes in time over three dimensions. Furthermore, the scales and rates of change in four dimensions may vary over several orders of magnitude. Geological explanations incorporate ideas from physics, chemistry, biology and engineering, lectures and textbooks provide a basic framework but they need to be amplified by laboratories and fieldwork involving active student participation and engagement. Being shown named 'things' is only a start to being able to being able to inculcate geological thinking that requires a wide and focused viewpoints. Kastens and Ishikawa (2006) suggested five aspects of thinking geologically, summarised as: 1. Observing, describing, recording, communicating geologically entities (ie basic cognitive skills) 2. (mentally) manipulating these entities 3. interpreting them via causal relationships 4. predicting other aspects using the basic knowledge (to create new knowledge) 5. using cognitive strategies to develop new ways of interpreting gained knowledge. These steps can be used follow the sequence from 'known' through 'need to know' to using knowledge to gain better geologic explanation, taken as enquiry-based or problem solving modes of education. These follow ideas from Dewey though Sternberg's 'thinking styles' and Siemens' connectivist approaches. Implementation of this basic schema needs to be structured for students in a complex geological world in line with Edelson's (2006) 'learning for' framework. In a geomorphological setting, this has been done by showing students how to interpret a landscape (landform, section etc) practice their skills and thus gain confidence with a tutor at hand. A web-based device, 'Virtorial' provides scenarios for students to practice interpretation (or even be assessed with). A cognitive tool is provided for landscape interpretation by division into the recognition of 'Materials' (rock, sediments etc), Processes (slope, glacial processes etc) and 'Geometry' (what it looks like). These components provide basic metadata for any landform in a landscape. Thus, the recognition of a landform means much more than a feature; the metadata provide contexts that can be used for interpretation in the field or laboratory, individually or in discussion groups, distance or field learning environments.

Airborne Geophysical Surveys Applied to Hydrocarbon Resource Development Environmental Studies

NASA Astrophysics Data System (ADS)

Smith, B. D.; Ball, L. B.; Finn, C.; Kass, A.; Thamke, J.

2014-12-01

Application of airborne geophysical surveys ranges in scale from detailed site scale such as locating abandoned well casing and saline water plumes to landscape scale for mapping hydrogeologic frameworks pertinent to ground water and tectonic settings relevant to studies of induced seismicity. These topics are important in understanding possible effects of hydrocarbon development on the environment. In addition airborne geophysical surveys can be used in establishing baseline "snapshots", to provide information in beneficial uses of produced waters, and in mapping ground water resources for use in well development. The U.S. Geological Survey (USGS) has conducted airborne geophysical surveys over more than 20 years for applications in energy resource environmental studies. A majority of these surveys are airborne electromagnetic (AEM) surveys to map subsurface electrical conductivity related to plumes of saline waters and more recently to map hydrogeologic frameworks for ground water and plume migration. AEM surveys have been used in the Powder River Basin of Wyoming to characterize the near surface geologic framework for siting produced water disposal ponds and for beneficial utilization in subsurface drip irrigation. A recent AEM survey at the Fort Peck Reservation, Montana, was used to map both shallow plumes from brine pits and surface infrastructure sources and a deeper concealed saline water plume from a failed injection well. Other reported applications have been to map areas geologically favorable for shallow gas that could influence drilling location and design. Airborne magnetic methods have been used to image the location of undocumented abandoned well casings which can serve as conduits to the near surface for coproduced waters. They have also been used in conjunction with geologic framework studies to understand the possible relationships between tectonic features and induced earthquakes in the Raton Basin. Airborne gravity as well as developing deeper mapping AEM surveys could also be effectively used in mapping tectonic features. Airborne radiometric methods have not been routinely used in hydrocarbon environmental studies but might be useful in understanding the surficial distribution of deposits related to naturally occurring radioactive materials.

ERTS-A data as a teaching and research tool in the Department of Geology

NASA Technical Reports Server (NTRS)

Grybeck, D. (Principal Investigator)

1973-01-01

The author has identified the following significant results. ERTS-1 prints have been used extensively in a geology of Alaska class to give a basic framework of the geology of the state. In addition, they have been intermittantly used in such diverse classes as: (1) Economic Geology (e.g. the Sn-bearing granites of the Seward Peninsula are particularly noticeable due to their wide contact metamorphic aureoles.) (2) A canned geology of Alaska lecture which has been given to two different introductory geology courses. (3) Structural Geology (e.g. the Fairweather and Denali faults are striking obvious). It was found most convenient for larger classes to prepare 35mm slides of the ERTS-1 prints that are used in conjunction with slides of the topographic and geologic maps at about the same scale. Thus the emphasis has been in integration of the ERTS-1 material into existing courses. As such, the ERTS-1 data has provided a unique and striking viewpoint that never fails to initiate favorable comment. In addition, prints have been examined by numerous researchers to develop a regional, integrated overview of such varied topics as regional geology to a background for local geologic mapping to studies of ore deposits and to the definition of a formation to be studied in detail at its type locality.

The interpretation of crustal dynamics data in terms of plate interactions and active tectonics of the Anatolian Plate and surrounding regions in the Middle East

NASA Technical Reports Server (NTRS)

Toksoz, M. Nafi

1988-01-01

The long-term objective of this project is to interpret NASA's Crustal Dynamics measurements (SLR) in the Eastern Mediterranean region in terms of relative plate movements and intraplate deformation. The approach is to combine realistic modeling studies with analysis of available geophysical and geological observations to provide a framework for interpreting NASA's measurements. This semi-annual report concentrates on recent results regarding the tectonics of Anatolia and surrounding regions from ground based observations. Also reported on briefly is progress in the use of the Global Positioning System to densify SLR observations in the Eastern Mediterranean. Reference is made to the previous annual report for a discussion of modeling results.

The road to NHDPlus — Advancements in digital stream networks and associated catchments

USGS Publications Warehouse

Moore, Richard B.; Dewald, Thomas A.

2016-01-01

A progression of advancements in Geographic Information Systems techniques for hydrologic network and associated catchment delineation has led to the production of the National Hydrography Dataset Plus (NHDPlus). NHDPlus is a digital stream network for hydrologic modeling with catchments and a suite of related geospatial data. Digital stream networks with associated catchments provide a geospatial framework for linking and integrating water-related data. Advancements in the development of NHDPlus are expected to continue to improve the capabilities of this national geospatial hydrologic framework. NHDPlus is built upon the medium-resolution NHD and, like NHD, was developed by the U.S. Environmental Protection Agency and U.S. Geological Survey to support the estimation of streamflow and stream velocity used in fate-and-transport modeling. Catchments included with NHDPlus were created by integrating vector information from the NHD and from the Watershed Boundary Dataset with the gridded land surface elevation as represented by the National Elevation Dataset. NHDPlus is an actively used and continually improved dataset. Users recognize the importance of a reliable stream network and associated catchments. The NHDPlus spatial features and associated data tables will continue to be improved to support regional water quality and streamflow models and other user-defined applications.

Petroleum potential of wilderness lands in the Western United States

USGS Publications Warehouse

Miller, Betty M.

1983-01-01

In 1982-83, the U.S. Geological Survey (USGS) conducted an investigation of the oil and gas potential of the designated and proposed Wilderness Lands in the Western United States. The scope of this study was limited to the assessment of conventional recoverable petroleum resources occurring in the designated and proposed Wilderness Lands of the Western United States that are administered under four Federal agencies: Bureau of Land Management (BLM), U.S. Forest Service (USFS), National Park Service (NPS), and Fish and Wildlife Service (FWS). The total area of the study included approximately 74 million acres of Wilderness Lands in these 11 Western States: Arizona, California, Colorado, Idaho, Montana, Nevada, New Mexico, Oregon, Utah, Washington, and Wyoming. The 74 million acres represent 31 percent of the total Federal lands within these 11 Western States. Approximately 49 percent of all the lands in these States are federally owned. The objective of this study was to assemble through various means all the available pertinent information that could be brought together within the USGS and integrate these data into a computer-based digital cartographic data system that was focused upon the single issue of reviewing the known geological and geophysical data to determine the geologic characteristics favorable or unfavorable for the occurrence of petroleum resources in these Wilderness Lands. In a joint effort in the USGS between the Geologic Division (GD) and the National Mapping Division (NMD) all of the mappable information used in this study was prepared and processed by using digital cartographic techniques. These include digitizing the location and boundaries of the Wilderness Lands; acreage calculations; the boundaries of the USGS petroleum provinces; and the geologic and tectonic boundaries within each petroleum province and State. In addition, searches were conducted on well data files which provided the locations and geologic information on over 5,000 wells drilled within or immediately adjacent to the Wilderness Lands. An analysis of all the geologic characteristics favorable or unfavorable for petroleum occurrence in conjunction with the geologic settings for the Wilderness Lands scattered within the framework of the petroleum provinces was performed by a team of geologists on each of the wilderness tracts. The geologic characteristics reviewed for each tract included the presence or absence of the following: adequate source beds and reservoir rocks; adequate trapping mechanisms; favorable thermal and maturation histories; presence of petroleum seeps or adjacent wells with shows or production; and the presence of favorable sedimentary rock sections underlying volcanic terrane or faulted and overthrust areas. A description of the geology and geologic framework is provided for each State along with an explanation of the interpretative geology and evaluation of the petroleum potential within the locale of each of the wilderness tracts. The assessment of the petroleum resources on the Wilderness Lands was completed in two separate stages. In the first stage the geologists evaluated the geological characteristics for the favorability or lack of favorability for the occurrence of oil and natural gas within each wilderness tract and assigned a qualitative rating for each tract's potential for the occurrence of recoverable oil and gas resources. In the second stage in evaluating the petroleum potential for the wilderness tracts, an effort was made to arrive at a quantitative assessment within the framework of the USGS's latest published resource estimates which are made on a province basis. The geologic characteristics evaluated for the favorability of petroleum occurrence within each of the clusters of wilderness tracts were the determining factors for the subjective assessments of the petroleum potential for each wilderness tract occurring within the respective basin or province. The quantitative resource

Hydrologic framework of Long Island, New York

USGS Publications Warehouse

Smolensky, Douglas A.; Buxton, Herbert T.; Shernoff, Peter K.

1990-01-01

Long Island, N.Y., is underlain by a mass of unconsolidated geologic deposits of clay, silt, sand, and gravel that overlie southward-sloping consolidated bedrock. These deposits are thinnest in northern Queens County (northwestern Long Island), where bedrock crops out, and increase to a maximum thickness of 2,000 ft in southeastern Long Island. This sequence of unconsolidated deposits consists of several distinct geologic units ranging in age from late Cretaceous through Pleistocene, with some recent deposits near shores and streams. These units are differentiated by age, depositional environment, and lithology in table 1. Investigations of ground-water availability and flow patterns may require information on the internal geometry of the hydrologic system that geologic correlations and interpretation alone cannot provide; hydrologic interpretations in which deposits are differentiated on the basis of water-transmitting properties are generally needed also. This set of maps and vertical sections depicts the hydrogeologic framework of the unconsolidated deposits that form Long Island's ground-water system. These deposits can be classified into eight major hydrogeologic units (table 1). The hydrogeologic interpretations presented herein are not everywhere consistent with strict geologic interpretation owing to facies changes and local variations in the water-transmitting properties within geologic units. These maps depict the upper-surface altitude of seven of the eight hydrogeologic units, which, in ascending order, are: consolidated bedrock, Lloyd aquifer, Raritan confining unit, Magothy aquifer, Monmouth greensand, Jameco aquifer, and Gardiners Clay. The upper glacial aquifer—the uppermost unit—is at land surface over most of Long Island and is, therefore, not included. The nine north-south hydrogeologic sections shown below depict the entire sequence of unconsolidated deposits and, together with the maps, provide a detailed three-dimensional interpretation of Long Island's hydrogeologic framework. The structure-contour map that shows the upper-surface altitude of the Cretaceous deposits is included to illustrate the erosional unconformity between the Cretaceous and overlying Pleistocene deposits. Pleistocene erosion played a major role in determining the shape and extent of the Lloyd aquifer, the Raritan confining unit, and the Magothy aquifer, and thus partly determined their hydrogeologic relation with subsequent (post-Cretaceous) deposits.

Shallow Geologic Framework and Geomorphic Evolution of a Paleo-barrier Shoreline, Terrebonne and Timbalier Bay, Louisiana, USA.

NASA Astrophysics Data System (ADS)

Culling, D. P.; Allison, M. A.; Kulp, M. A.; Georgiou, I. Y.; Weathers, H. D., III

2016-12-01

The Louisiana coast is an invaluable asset to the nation's human, economic, and ecological welfare. However, due to the combined effects of coastal erosion, subsidence, and sea level rise, Louisiana is losing on average 25 km2 of its valuable coastal wetlands per year. Terrebonne- Timbalier Bay and the associated Lafourche deltaic lobe headland is a critical section of this coast for wetlands and infrastructure protection and restoration in the State's Master Plan. Historical imagery and bathymetry clearly show the rapid transgression and erosional degradation of both sets of headland-flanking barrier island shorelines due to wave attack and relative sea level rise in the past 150 y. The focus of the present study is a barrier island system: an ocean-fronting modern-barrier shoreline and a paleo-deltaic headland barrier arc inland of the active barrier. The evolution of the modern barrier arc is closely tied to the shallow geologic framework over which it is transgressing, and specifically the sand re-activation capacity of the antecedent geology once erosional forces are introduced. To understand the evolution of these barrier systems and how to address their protection and re-nourishment, it is important to quantify (1) the depositional facies geometry and (2) the volume of sand in these back-barrier sandy lithosomes. Here we present new observations from CHIRP sub-bottom seismic multibeam bathymetry and LIDAR topography, and surface grab and vibracore sampling in an effort to quantify the sediment availability within the underlying geologic framework and reconstruct the geomorphic evolution of these barrier shorelines. Preliminary results show the morphologic expression of antecedent geology, which is evident in seismic and bathymetric patterns, and the presence of near-surface and surface sandy stratigraphy within the back barrier bay. Observations of sandy units agree with results from Kulp et al. (2005), who showed the presence and extent of sandy lithofacies within 3 m of the surface proximal to the Raccoon Pass tidal-inlet. We suggest this sand is an important potential resource for the longevity of proximal sandy barriers as transgression continues; one identified lithesome alone is estimated to contain 5.25 km3 of fine-grained sand.

INEEL Subregional Conceptual Model Report; Volume 1 - Summary of Existing Knowledge of Natural and Anthropogenic Influences Governing Subsurface Contaminant Transport in the INEEL Subregion of the Eastern Snake River Plain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wichlacz, Paul Louis; Orr, Brennan

2002-08-01

The National Research Council has defined a conceptual model as ''an evolving hypothesis identifying the important features, processes, and events controlling fluid flow and contaminant transport of consequence at a specific field site in the context of a recognized problem''. Presently, several subregional conceptual models are under development at the Idaho National Engineering and Environmental Laboratory (INEEL). Additionally, facility-specific conceptual models have been described as part of INEEL environmental restoration activities. Compilation of these models is required to develop a comprehensive conceptual model that can be used to strategically plan for future groundwater research activities at the INEEL. Conceptual modelsmore » of groundwater flow and contaminant transport at the INEEL include the description of the geologic framework, matrix hydraulic properties, and inflows and outflows. They also include definitions of the contaminant source term and contaminant transport mechanisms. The geologic framework of the INEEL subregion is described by the geometry of the system, stratigraphic units within the system, and structural features that affect groundwater flow and contaminant transport. These elements define geohydrologic units that make up the Snake River Plain Aquifer (SRPA). The United States Geological Survey (USGS) conceptual model encompasses approximately 1,920 mi2 of the eastern Snake River Plain. The Waste Area Group (WAG)-10 model includes the USGS area and additional areas to the northeast and southeast. Both conceptual models are bounded to the northwest by the Pioneer Mountains, Lost River Range, and Lemhi Mountains. They are bounded to the southeast by groundwater flow paths determined from aquifer water-level contours. The upgradient extent of the USGS model is a water-level contour that includes the northeastern boundary of the INEEL. The WAG-10 model includes more of the Mud Lake area to utilize previous estimates of underflow into the subregion. Both conceptual models extend approximately 25 miles to the southwest of the INEEL, a distance sufficient to include known concentrations of contaminant tracers. Several hypotheses have been developed concerning the effective thickness of the SRPA at the INEEL. The USGS model has defined the effective thickness from electrical resistivity and borehole data to be as much as 2,500 ft in the eastern part of the subregion and as much as 4,000 ft in the southwestern part. The WAG-10 model has developed two alternatives using aquifer-temperature and electrical resistivity data. The ''thick'' aquifer interpretation utilizes colder temperature data and includes a northtrending zone in which the thickness exceeds 1,300 ft and with a maximum thickness of 1,700 ft. The ''thin'' aquifer interpretation minimizes aquifer thickness, with thickness ranging from 328 to 1,300 ft. Facility-specific models generally have focused efforts on the upper 250 ft of saturation. Conceptual models have utilized a stratigraphic data set to define geohydrologic units within the INEEL subregion. This data set, compiled from geophysical logs and cores from boreholes, correlates the thick, complex stack of basalt flows across the subregion. Conceptual models generally concur that the upper geohydrologic unit consists of a section of highly fractured, multiple, thin basalt flows and sedimentary interbeds. Beneath this unit is an areally extensive, thick, unfractured basalt flow that rises above the water table southwest of the INEEL. The bottom unit consists of a thick section of slightly- to moderately-altered basalt. A key objective of the DOE water-integration project at the INEEL is to coordinate development of a subregional conceptual model of groundwater flow and contaminant transport that is based on the best available understanding of geologic and hydrologic features. The first step in this process is to compile and summarize the current conceptual models of groundwater flow and contaminant transport at the INEEL that have been developed from extensive geohydrologic studies conducted during the last 50 years.« less

Multi-model approach to petroleum resource appraisal using analytic methodologies for probabilistic systems

USGS Publications Warehouse

Crovelli, R.A.

1988-01-01

The geologic appraisal model that is selected for a petroleum resource assessment depends upon purpose of the assessment, basic geologic assumptions of the area, type of available data, time available before deadlines, available human and financial resources, available computer facilities, and, most importantly, the available quantitative methodology with corresponding computer software and any new quantitative methodology that would have to be developed. Therefore, different resource assessment projects usually require different geologic models. Also, more than one geologic model might be needed in a single project for assessing different regions of the study or for cross-checking resource estimates of the area. Some geologic analyses used in the past for petroleum resource appraisal involved play analysis. The corresponding quantitative methodologies of these analyses usually consisted of Monte Carlo simulation techniques. A probabilistic system of petroleum resource appraisal for play analysis has been designed to meet the following requirements: (1) includes a variety of geologic models, (2) uses an analytic methodology instead of Monte Carlo simulation, (3) possesses the capacity to aggregate estimates from many areas that have been assessed by different geologic models, and (4) runs quickly on a microcomputer. Geologic models consist of four basic types: reservoir engineering, volumetric yield, field size, and direct assessment. Several case histories and present studies by the U.S. Geological Survey are discussed. ?? 1988 International Association for Mathematical Geology.

New Age of 3D Geological Modelling or Complexity is not an Issue Anymore

NASA Astrophysics Data System (ADS)

Mitrofanov, Aleksandr

2017-04-01

Geological model has a significant value in almost all types of researches related to regional mapping, geodynamics and especially to structural and resource geology of mineral deposits. Well-developed geological model must take into account all vital features of modelling object without over-simplification and also should adequately represent the interpretation of the geologist. In recent years with the gradual exhaustion deposits with relatively simple morphology geologists from all over the world are faced with the necessity of building the representative models for more and more structurally complex objects. Meanwhile, the amount of tools used for that has not significantly changed in the last two-three decades. The most widespread method of wireframe geological modelling now was developed in 1990s and is fully based on engineering design set of instruments (so-called CAD). Strings and polygons representing the section-based interpretation are being used as an intermediate step in the process of wireframes generation. Despite of significant time required for this type of modelling, it still can provide sufficient results for simple and medium-complexity geological objects. However, with the increasing complexity more and more vital features of the deposit are being sacrificed because of fundamental inability (or much greater time required for modelling) of CAD-based explicit techniques to develop the wireframes of the appropriate complexity. At the same time alternative technology which is not based on sectional approach and which uses the fundamentally different mathematical algorithms is being actively developed in the variety of other disciplines: medicine, advanced industrial design, game and cinema industry. In the recent years this implicit technology started to being developed for geological modelling purpose and nowadays it is represented by very powerful set of tools that has been integrated in almost all major commercial software packages. Implicit modelling allows to develop geological models that really correspond with complicated geological reality. Models can include fault blocking, complex structural trends and folding; can be based on excessive input dataset (like lots of drilling on the mining stage) or, on the other hand, on a quite few drillholes intersections with significant input from geological interpretation of the deposit. In any case implicit modelling, if is used correctly, allows to incorporate the whole batch of geological data and relatively quickly get the easily adjustable, flexible and robust geological wireframes that can be used as a reliable foundation on the following stages of geological investigations. In SRK practice nowadays almost all the wireframe models used for structural and resource geology are developed with implicit modelling tools which significantly increased the speed and quality of geological modelling.

Geologic map and database of the Roseburg 30' x 60' quadrangle, Douglas and Coos counties, Oregon

USGS Publications Warehouse

Wells, Ray E.; Jayko, A.S.; Niem, A.R.; Black, G.; Wiley, T.; Baldwin, E.; Molenaar, K.M.; Wheeler, K.L.; DuRoss, C.B.; Givler, R.W.

2001-01-01

The Roseburg 30' x 60' Quadrangle covers the southeastern margin of the Oregon Coast Range and its tectonic boundary with Mesozoic terranes of the Klamath Mountains (see figures 1 and 2 in pamphlet, also shown on map sheet). The geologic framework of the Roseburg area was established by the pioneering work of Diller (1898), Wells and Peck, (1961) and Ewart Baldwin (1974) and his students (see figure 3 in pamphlet, also shown on map sheet). Baldwin and his students focussed on the history of the Eocene Tyee basin, where the sediments lap across the tectonic boundary with the Mesozoic terranes and record the accretion of the Coast Range basement to the continent. Others have examined the sedimentary fill of the Tyee basin in detail, recognizing the deep marine turbidite facies of the Tyee Formation (Snavely and others, 1964) and proposing several models for the Eocene evolution of the forearc basin (Heller and Ryberg, 1983; Chan and Dott, 1983; Heller and Dickinson, 1985; Molenaar, 1985; see Ryu and others, 1992 for a comprehensive summary). Along the eastern margin of the quadrangle, both the Tyee basin and the Klamath terranes are overlain by Eocene volcanic rocks of the Western Cascade arc (Walker and MacLeod, 1991). The thick Eocene sedimentary sequence of the Tyee basin has significant oil and gas potential (Armentrout and Suek, 1985; Gautier and others, 1993; Ryu and others, 1996). Although 13 deep test wells have been drilled in the Roseburg quadrangle (see figure 2 and table 1 in pamphlet, also shown on map sheet), exploration to date has been hampered by an incomplete understanding of the basin�s tectonic setting and evolution. In response, the Oregon Department of Geology and Mineral Industries (DOGAMI) initiated a five year assessment of the oil and gas potential of the Tyee basin. This map is a product of a cooperative effort by the U. S. Geological Survey, Oregon State University, and DOGAMI to systematically map the sedimentary facies and structure of the Tyee basin. New geologic mapping of twenty-eight 7.5' quadrangles is summarized on the map (see figure 3, also shown on map sheet), and the digital database contains geologic information suitable for both 1:100K and 1:24K scale analysis. DOGAMI has published a compilation and synthesis of previous mapping (Niem and Niem, 1990), a basin-wide sequence stratigraphic model and correlations (Ryu and others, 1992), and a report on the oil and gas potential (Ryu and others, 1996). Readers interested in the oil and gas potential of the Roseburg quadrangle should use the map in combination with Ryu and others (1996) to address specific stratigraphic units and structural plays. Stratigraphic terminology for the Tyee basin adopts the type sections, formation names, and framework of Ryu and others (1992, 1996), which were developed concurrently with the mapping and are recognized throughout the basin. For detailed discussion of nomenclature, type sections, lithology, thickness and distribution, age, contact relationships, and depositional environment of stratigraphic units, the reader is referred to Ryu and others (1992). In this report we focus on the spatial, temporal, and structural relationships between units revealed by geologic mapping. Map unit ages (see figure 4 in pamphlet, also shown on map sheeet) are adjusted slightly from Ryu and others (1992, 1996) to fit new coccolith age determinations (D. Bukry, cited in pamphlet), paleomagnetic polarity data (Simpson, 1977 and new data cited in pamphlet), and the time scale of Berggren and others (1995).

Assessment of effectiveness of geologic isolation systems. Geologic-simulation model for a hypothetical site in the Columbia Plateau. Volume 2: results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foley, M.G.; Petrie, G.M.; Baldwin, A.J.

1982-06-01

This report contains the input data and computer results for the Geologic Simulation Model. This model is described in detail in the following report: Petrie, G.M., et. al. 1981. Geologic Simulation Model for a Hypothetical Site in the Columbia Plateau, Pacific Northwest Laboratory, Richland, Washington. The Geologic Simulation Model is a quasi-deterministic process-response model which simulates, for a million years into the future, the development of the geologic and hydrologic systems of the ground-water basin containing the Pasco Basin. Effects of natural processes on the ground-water hydrologic system are modeled principally by rate equations. The combined effects and synergistic interactionsmore » of different processes are approximated by linear superposition of their effects during discrete time intervals in a stepwise-integration approach.« less

Progress on Discrete Fracture Network models with implications on the predictions of permeability and flow channeling structure

NASA Astrophysics Data System (ADS)

Darcel, C.; Davy, P.; Le Goc, R.; Maillot, J.; Selroos, J. O.

2017-12-01

We present progress on Discrete Fracture Network (DFN) flow modeling, including realistic advanced DFN spatial structures and local fracture transmissivity properties, through an application to the Forsmark site in Sweden. DFN models are a framework to combine fracture datasets from different sources and scales and to interpolate them in combining statistical distributions and stereological relations. The resulting DFN upscaling function - size density distribution - is a model component key to extrapolating fracture size densities between data gaps, from borehole core up to site scale. Another important feature of DFN models lays in the spatial correlations between fractures, with still unevaluated consequences on flow predictions. Indeed, although common Poisson (i.e. spatially random) models are widely used, they do not reflect these geological evidences for more complex structures. To model them, we define a DFN growth process from kinematic rules for nucleation, growth and stopping conditions. It mimics in a simplified way the geological fracturing processes and produces DFN characteristics -both upscaling function and spatial correlations- fully consistent with field observations. DFN structures are first compared for constant transmissivities. Flow simulations for the kinematic and equivalent Poisson DFN models show striking differences: with the kinematic DFN, connectivity and permeability are significantly smaller, down to a difference of one order of magnitude, and flow is much more channelized. Further flow analyses are performed with more realistic transmissivity distribution conditions (sealed parts, relations to fracture sizes, orientations and in-situ stress field). The relative importance of the overall DFN structure in the final flow predictions is discussed.

Measuring novices' field mapping abilities using an in-class exercise based on expert task analysis

NASA Astrophysics Data System (ADS)

Caulkins, J. L.

2010-12-01

We are interested in developing a model of expert-like behavior for improving the teaching methods of undergraduate field geology. Our aim is to assist students in mastering the process of field mapping more efficiently and effectively and to improve their ability to think creatively in the field. To examine expert-mapping behavior, a cognitive task analysis was conducted with expert geologic mappers in an attempt to define the process of geologic mapping (i.e. to understand how experts carry out geological mapping). The task analysis indicates that expert mappers have a wealth of geologic scenarios at their disposal that they compare against examples seen in the field, experiences that most undergraduate mappers will not have had. While presenting students with many geological examples in class may increase their understanding of geologic processes, novices still struggle when presented with a novel field situation. Based on the task analysis, a short (45-minute) paper-map-based exercise was designed and tested with 14 pairs of 3rd year geology students. The exercise asks students to generate probable geologic models based on a series of four (4) data sets. Each data set represents a day’s worth of data; after the first “day,” new sheets simply include current and previously collected data (e.g. “Day 2” data set includes data from “Day 1” plus the new “Day 2” data). As the geologic complexity increases, students must adapt, reject or generate new geologic models in order to fit the growing data set. Preliminary results of the exercise indicate that students who produced more probable geologic models, and produced higher ratios of probable to improbable models, tended to go on to do better on the mapping exercises at the 3rd year field school. These results suggest that those students with more cognitively available geologic models may be more able to use these models in field settings than those who are unable to draw on these models for whatever reason. Giving students practice at generating geologic models to explain data may be useful in preparing our students for field mapping exercises.

A national geographic framework for guiding conservation on a landscape scale

USGS Publications Warehouse

Millard, Michael J.; Czarnecki, Craig A.; Morton, John M.; Brandt, Laura A.; Briggs, Jennifer S.; Shipley, Frank S.; Sayre, Roger G.; Sponholtz, Pamela J.; Perkins, David; Simpkins, Darin G.; Taylor, Janith

2012-01-01

The U.S. Fish and Wildlife Service, along with the global conservation community, has recognized that the conservation challenges of the 21st century far exceed the responsibilities and footprint of any individual agency or program. The ecological effects of climate change and other anthropogenic stressors do not recognize geopolitical boundaries and, as such, demand a national geographic framework to provide structure for cross-jurisdictional and landscape-scale conservation strategies. In 2009, a new map of ecologically based conservation regions in which to organize capacity and implement strategic habitat conservation was developed using rapid prototyping and expert elicitation by an interagency team of U.S. Fish and Wildlife Service and U.S. Geological Survey scientists and conservation professionals. Incorporating Bird Conservation Regions, Freshwater Ecoregions, and U.S. Geological Survey hydrologic unit codes, the new geographic framework provides a spatial template for building conservation capacity and focusing biological planning and conservation design efforts. The Department of Interior's Landscape Conservation Cooperatives are being organized in these new conservation regions as multi-stakeholder collaborations for improved conservation science and management.

Database for the geologic map of the Sauk River 30-minute by 60-minute quadrangle, Washington (I-2592)

USGS Publications Warehouse

Tabor, R.W.; Booth, D.B.; Vance, J.A.; Ford, A.B.

2006-01-01

This digital map database has been prepared by R.W. Tabor from the published Geologic map of the Sauk River 30- by 60 Minute Quadrangle, Washington. Together with the accompanying text files as PDF, it provides information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The authors mapped most of the bedrock geology at 1:100,000 scale, but compiled most Quaternary units at 1:24,000 scale. The Quaternary contacts and structural data have been much simplified for the 1:100,000-scale map and database. The spatial resolution (scale) of the database is 1:100,000 or smaller. This database depicts the distribution of geologic materials and structures at a regional (1:100,000) scale. The report is intended to provide geologic information for the regional study of materials properties, earthquake shaking, landslide potential, mineral hazards, seismic velocity, and earthquake faults. In addition, the report contains information and interpretations about the regional geologic history and framework. However, the regional scale of this report does not provide sufficient detail for site development purposes.

A framework for assessing water and proppant use and flowback water extraction associated with development of continuous petroleum resources

USGS Publications Warehouse

Haines, Seth S.; Cook, Troy; Thamke, Joanna N.; Davis, Kyle W.; Long, Andrew J.; Healy, Richard W.; Hawkins, Sarah J.; Engle, Mark A.

2014-01-01

The U.S. Geological Survey is developing approaches for the quantitative assessment of water and proppant involved with possible future production of continuous petroleum deposits. The assessment approach is an extension of existing U.S. Geological Survey petroleum-assessment methods, and it aims to provide objective information that helps decision makers understand the tradeoffs inherent in resource-development decisions. This fact sheet provides an overview of U.S. Geological Survey assessments for quantities of water and proppant required for drilling and hydraulic fracturing and for flowback water extracted with petroleum; the report also presents the form of the intended assessment output information.

Adaptive management for subsurface pressure and plume control in application to geological CO2 storage

NASA Astrophysics Data System (ADS)

Gonzalez-Nicolas, A.; Cihan, A.; Birkholzer, J. T.; Petrusak, R.; Zhou, Q.; Riestenberg, D. E.; Trautz, R. C.; Godec, M.

2016-12-01

Industrial-scale injection of CO2 into the subsurface can cause reservoir pressure increases that must be properly controlled to prevent any potential environmental impact. Excessive pressure buildup in reservoir may result in ground water contamination stemming from leakage through conductive pathways, such as improperly plugged abandoned wells or distant faults, and the potential for fault reactivation and possibly seal breaching. Brine extraction is a viable approach for managing formation pressure, effective stress, and plume movement during industrial-scale CO2 injection projects. The main objectives of this study are to investigate suitable different pressure management strategies involving active brine extraction and passive pressure relief wells. Adaptive optimized management of CO2 storage projects utilizes the advanced automated optimization algorithms and suitable process models. The adaptive management integrates monitoring, forward modeling, inversion modeling and optimization through an iterative process. In this study, we employ an adaptive framework to understand primarily the effects of initial site characterization and frequency of the model update (calibration) and optimization calculations for controlling extraction rates based on the monitoring data on the accuracy and the success of the management without violating pressure buildup constraints in the subsurface reservoir system. We will present results of applying the adaptive framework to test appropriateness of different management strategies for a realistic field injection project.

SLIVISU, an Interactive Visualisation Framework for Analysis of Geological Sea-Level Indicators

NASA Astrophysics Data System (ADS)

Klemann, V.; Schulte, S.; Unger, A.; Dransch, D.

2011-12-01

Flanking data analysis in earth system sciences by advanced visualisation tools is a striking feature due to rising complexity, amount and variety of available data. With respect to sea-level indicators (SLIs), their analysis in earth-system applications, such as modelling and simulation on regional or global scales, demands the consideration of large amounts of data - we talk about thousands of SLIs - and, so, to go ahead of analysing single sea-level curves. On the other hand, a gross analysis by means of statistical methods is hindered by the often heterogeneous and individual character of the single SLIs, i.e., the spatio-temporal context and often heterogenous information is difficult to handle or to represent in an objective way. Therefore a concept of integrating automated analysis and visualisation is mandatory. This is provided by visual analytics. As an implementation of this concept, we present the visualisation framework SLIVISU, developed at GFZ, which bases on multiple linked views and provides a synoptic analysis of observational data, model configurations, model outputs and results of automated analysis in glacial isostatic adjustment. Starting as a visualisation tool for an existing database of SLIs, it now serves as an analysis tool for the evaluation of model simulations in studies of glacial-isostatic adjustment.

Marine magnetic survey and onshore gravity and magnetic survey, San Pablo Bay, northern California

USGS Publications Warehouse

Ponce, David A.; Denton, Kevin M.; Watt, Janet T.

2016-09-12

IntroductionFrom November 2011 to August 2015, the U.S. Geological Survey (USGS) collected more than 1,000 line-kilometers (length of lines surveyed in kilometers) of marine magnetic data on San Pablo Bay, 98 onshore gravity stations, and over 27 line-kilometers of ground magnetic data in northern California. Combined magnetic and gravity investigations were undertaken to study subsurface geologic structures as an aid in understanding the geologic framework and earthquake hazard potential in the San Francisco Bay Area. Furthermore, marine magnetic data illuminate local subsurface geologic features in the shallow crust beneath San Pablo Bay where geologic exposure is absent.Magnetic and gravity methods, which reflect contrasting physical properties of the subsurface, are ideal for studying San Pablo Bay. Exposed rock units surrounding San Pablo Bay consist mainly of Jurassic Coast Range ophiolite, Great Valley sequence, Franciscan Complex rocks, Miocene sedimentary rocks, and unconsolidated alluvium (Graymer and others, 2006). The contrasting magnetic and density properties of these rocks enable us to map their subsurface extent.

Bedrock geologic map of the Grafton quadrangle, Worcester County, Massachusetts

USGS Publications Warehouse

Walsh, Gregory J.; Aleinikoff, John N.; Dorais, Michael J.

2011-01-01

The bedrock geology of the 7.5-minute Grafton, Massachusetts, quadrangle consists of deformed Neoproterozoic to early Paleozoic crystalline metamorphic and intrusive igneous rocks. Neoproterozoic intrusive, metasedimentary, and metavolcanic rocks crop out in the Avalon zone, and Cambrian to Silurian intrusive, metasedimentary, and metavolcanic rocks crop out in the Nashoba zone. Rocks of the Avalon and Nashoba zones, or terranes, are separated by the Bloody Bluff fault. The bedrock geology was mapped to study the tectonic history of the area and to provide a framework for ongoing hydrogeologic characterization of the fractured bedrock of Massachusetts. This report presents mapping by G.J. Walsh, geochronology by J.N. Aleinikoff, geochemistry by M.J. Dorais, and consists of a map, text pamphlet, and GIS database. The map and text pamphlet are available in paper format or as downloadable files (see frame at right). The GIS database is available for download. The database includes contacts of bedrock geologic units, faults, outcrops, structural geologic information, and photographs.

National Assessment of Oil and Gas Project: petroleum systems and geologic assessment of oil and gas in the Southwestern Wyoming Province, Wyoming, Colorado and Utah

USGS Publications Warehouse

,

2005-01-01

The U.S. Geological Survey (USGS) completed an assessment of the undiscovered oil and gas potential of the Southwestern Wyoming Province of southwestern Wyoming, northwestern Colorado, and northeastern Utah (fig. 1). The USGS Southwestern Wyoming Province for this assessment included the Green River Basin, Moxa arch, Hoback Basin, Sandy Bend arch, Rock Springs uplift, Great Divide Basin, Wamsutter arch, Washakie Basin, Cherokee ridge, and the Sand Wash Basin. The assessment of the Southwestern Wyoming Province is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation, and migration), reservoir rocks (sequence stratigraphy, petrophysical properties), and hydrocarbon traps (trap types, formation, and timing). Using this geologic framework, the USGS defined 9 total petroleum systems (TPS) and 23 assessment units (AU) within these TPSs, and quantitatively estimated the undiscovered oil and gas resources within 21 of the 23 AUs.

The application of geologic remote sensing to vertebrate biostratigraphy - General results from the Wind River Basin, Wyoming

NASA Technical Reports Server (NTRS)

Stucky, Richard K.; Krishtalka, Leonard

1991-01-01

Since 1986, remote sensing images derived from satellite and aircraft-borne sensor data have been used to study the stratigraphy and sedimentology of the vertebrate-bearing Wind River and Wagon Bed formations in the Wind River Basin (Wyoming). Landsat 5 TM and aircraft Thermal Infrared Multispectral Scanner data were combined with conventional geologic analyses. The remote sensing data have contributed significantly to: (1) geologic mapping at the formation, member, and bed levels; (2) stratigraphic correlation; (3) reconstruction of ancient depositional environments; and (4) identification of structural complexity. This information is critical to vertebrate paleontology in providing the stratigraphic, sedimentologic, and structural framework required for evolutionary and paleoecologic studies. Of primary importance is the ability to map at minimal cost the geology of large areas (20,000 sq km or greater) at a high level of precision. Remote sensing data can be especially useful in geologically and paleontologically unexplored or poorly understood regions.

Guiding principles of USGS methodology for assessment of undiscovered conventional oil and gas resources

USGS Publications Warehouse

Charpentier, R.R.; Klett, T.R.

2005-01-01

During the last 30 years, the methodology for assessment of undiscovered conventional oil and gas resources used by the Geological Survey has undergone considerable change. This evolution has been based on five major principles. First, the U.S. Geological Survey has responsibility for a wide range of U.S. and world assessments and requires a robust methodology suitable for immaturely explored as well as maturely explored areas. Second, the assessments should be based on as comprehensive a set of geological and exploration history data as possible. Third, the perils of methods that solely use statistical methods without geological analysis are recognized. Fourth, the methodology and course of the assessment should be documented as transparently as possible, within the limits imposed by the inevitable use of subjective judgement. Fifth, the multiple uses of the assessments require a continuing effort to provide the documentation in such ways as to increase utility to the many types of users. Undiscovered conventional oil and gas resources are those recoverable volumes in undiscovered, discrete, conventional structural or stratigraphic traps. The USGS 2000 methodology for these resources is based on a framework of assessing numbers and sizes of undiscovered oil and gas accumulations and the associated risks. The input is standardized on a form termed the Seventh Approximation Data Form for Conventional Assessment Units. Volumes of resource are then calculated using a Monte Carlo program named Emc2, but an alternative analytic (non-Monte Carlo) program named ASSESS also can be used. The resource assessment methodology continues to change. Accumulation-size distributions are being examined to determine how sensitive the results are to size-distribution assumptions. The resource assessment output is changing to provide better applicability for economic analysis. The separate methodology for assessing continuous (unconventional) resources also has been evolving. Further studies of the relationship between geologic models of conventional and continuous resources will likely impact the respective resource assessment methodologies. ?? 2005 International Association for Mathematical Geology.

Coupled Modeling of Flow, Transport, and Deformation during Hydrodynamically Unstable Displacement in Fractured Rocks

NASA Astrophysics Data System (ADS)

Jha, B.; Juanes, R.

2015-12-01

Coupled processes of flow, transport, and deformation are important during production of hydrocarbons from oil and gas reservoirs. Effective design and implementation of enhanced recovery techniques such as miscible gas flooding and hydraulic fracturing requires modeling and simulation of these coupled proceses in geologic porous media. We develop a computational framework to model the coupled processes of flow, transport, and deformation in heterogeneous fractured rock. We show that the hydrocarbon recovery efficiency during unstable displacement of a more viscous oil with a less viscous fluid in a fractured medium depends on the mechanical state of the medium, which evolves due to permeability alteration within and around fractures. We show that fully accounting for the coupling between the physical processes results in estimates of the recovery efficiency in agreement with observations in field and lab experiments.

Geologic framework of the regional ground-water flow system in the Upper Deschutes Basin, Oregon

USGS Publications Warehouse

Lite, Kenneth E.; Gannett, Marshall W.

2002-12-10

Geologic units in the Deschutes Basin were divided into several distinct hydrogeologic units. In some instances the units correspond to existing stratigraphic divisions. In other instances, hydrogeologic units correspond to different facies within a single stratigraphic unit or formation. The hydrogeologic units include Quaternary sediment, deposits of the Cascade Range and Newberry Volcano, four zones within the Deschutes Formation and age-equivalent rocks that roughly correspond with depositional environments, and pre-Deschutes-age strata.

Catchment Classification: Connecting Climate, Structure and Function

NASA Astrophysics Data System (ADS)

Sawicz, K. A.; Wagener, T.; Sivapalan, M.; Troch, P. A.; Carrillo, G. A.

2010-12-01

Hydrology does not yet possess a generally accepted catchment classification framework. Such a classification framework needs to: [1] give names to things, i.e. the main classification step, [2] permit transfer of information, i.e. regionalization of information, [3] permit development of generalizations, i.e. to develop new theory, and [4] provide a first order environmental change impact assessment, i.e., the hydrologic implications of climate, land use and land cover change. One strategy is to create a catchment classification framework based on the notion of catchment functions (partitioning, storage, and release). Results of an empirical study presented here connects climate and structure to catchment function (in the form of select hydrologic signatures), based on analyzing over 300 US catchments. Initial results indicate a wide assortment of signature relationships with properties of climate, geology, and vegetation. The uncertainty in the different regionalized signatures varies widely, and therefore there is variability in the robustness of classifying ungauged basins. This research provides insight into the controls of hydrologic behavior of a catchment, and enables a classification framework applicable to gauged and ungauged across the study domain. This study sheds light on what we can expect to achieve in mapping climate, structure and function in a top-down manner. Results of this study complement work done using a bottom-up physically-based modeling framework to generalize this approach (Carrillo et al., this session).

The future of structural fieldwork - UAV assisted aerial photogrammetry

NASA Astrophysics Data System (ADS)

Vollgger, Stefan; Cruden, Alexander

2015-04-01

Unmanned aerial vehicles (UAVs), commonly referred to as drones, are opening new and low cost possibilities to acquire high-resolution aerial images and digital surface models (DSM) for applications in structural geology. UAVs can be programmed to fly autonomously along a user defined grid to systematically capture high-resolution photographs, even in difficult to access areas. The photographs are subsequently processed using software that employ SIFT (scale invariant feature transform) and SFM (structure from motion) algorithms. These photogrammetric routines allow the extraction of spatial information (3D point clouds, digital elevation models, 3D meshes, orthophotos) from 2D images. Depending on flight altitude and camera setup, sub-centimeter spatial resolutions can be achieved. By "digitally mapping" georeferenced 3D models and images, orientation data can be extracted directly and used to analyse the structural framework of the mapped object or area. We present UAV assisted aerial mapping results from a coastal platform near Cape Liptrap (Victoria, Australia), where deformed metasediments of the Palaeozoic Lachlan Fold Belt are exposed. We also show how orientation and spatial information of brittle and ductile structures extracted from the photogrammetric model can be linked to the progressive development of folds and faults in the region. Even though there are both technical and legislative limitations, which might prohibit the use of UAVs without prior commercial licensing and training, the benefits that arise from the resulting high-resolution, photorealistic models can substantially contribute to the collection of new data and insights for applications in structural geology.

Death Valley regional ground-water flow system, Nevada and California -- hydrogeologic framework and transient ground-water flow model

USGS Publications Warehouse

Belcher, Wayne R.

2004-01-01

A numerical three-dimensional (3D) transient ground-water flow model of the Death Valley region was developed by the U.S. Geological Survey for the U.S. Department of Energy programs at the Nevada Test Site and at Yucca Mountain, Nevada. Decades of study of aspects of the ground-water flow system and previous less extensive ground-water flow models were incorporated and reevaluated together with new data to provide greater detail for the complex, digital model. A 3D digital hydrogeologic framework model (HFM) was developed from digital elevation models, geologic maps, borehole information, geologic and hydrogeologic cross sections, and other 3D models to represent the geometry of the hydrogeologic units (HGUs). Structural features, such as faults and fractures, that affect ground-water flow also were added. The HFM represents Precambrian and Paleozoic crystalline and sedimentary rocks, Mesozoic sedimentary rocks, Mesozoic to Cenozoic intrusive rocks, Cenozoic volcanic tuffs and lavas, and late Cenozoic sedimentary deposits of the Death Valley Regional Ground-Water Flow System (DVRFS) region in 27 HGUs. Information from a series of investigations was compiled to conceptualize and quantify hydrologic components of the ground-water flow system within the DVRFS model domain and to provide hydraulic-property and head-observation data used in the calibration of the transient-flow model. These studies reevaluated natural ground-water discharge occurring through evapotranspiration and spring flow; the history of ground-water pumping from 1913 through 1998; ground-water recharge simulated as net infiltration; model boundary inflows and outflows based on regional hydraulic gradients and water budgets of surrounding areas; hydraulic conductivity and its relation to depth; and water levels appropriate for regional simulation of prepumped and pumped conditions within the DVRFS model domain. Simulation results appropriate for the regional extent and scale of the model were provided by acquiring additional data, by reevaluating existing data using current technology and concepts, and by refining earlier interpretations to reflect the current understanding of the regional ground-water flow system. Ground-water flow in the Death Valley region is composed of several interconnected, complex ground-water flow systems. Ground-water flow occurs in three subregions in relatively shallow and localized flow paths that are superimposed on deeper, regional flow paths. Regional ground-water flow is predominantly through a thick Paleozoic carbonate rock sequence affected by complex geologic structures from regional faulting and fracturing that can enhance or impede flow. Spring flow and evapotranspiration (ET) are the dominant natural ground-water discharge processes. Ground water also is withdrawn for agricultural, commercial, and domestic uses. Ground-water flow in the DVRFS was simulated using MODFLOW-2000, a 3D finite-difference modular ground-water flow modeling code that incorporates a nonlinear least-squares regression technique to estimate aquifer parameters. The DVRFS model has 16 layers of defined thickness, a finite-difference grid consisting of 194 rows and 160 columns, and uniform cells 1,500 m on each side. Prepumping conditions (before 1913) were used as the initial conditions for the transient-state calibration. The model uses annual stress periods with discrete recharge and discharge components. Recharge occurs mostly from infiltration of precipitation and runoff on high mountain ranges and from a small amount of underflow from adjacent basins. Discharge occurs primarily through ET and spring discharge (both simulated as drains) and water withdrawal by pumping and, to a lesser amount, by underflow to adjacent basins, also simulated by drains. All parameter values estimated by the regression are reasonable and within the range of expected values. The simulated hydraulic heads of the final calibrated transient model gener

Geologic framework and petroleum systems of Cook Inlet basin, south-central Alaska

USGS Publications Warehouse

LePain, D.L.; Stanley, Richard G.; Helmold, K.P.; Shellenbaum, D.P.; Stone, D.M.; Hite, D.M.

2013-01-01

This report provides a comprehensive overview of the stratigraphy, structure, tectonics, and petroleum systems of the Cook Inlet basin, an important oil- and gas-producing region in south-central Alaska.

Joint Inversion Modelling of Geophysical Data From Lough Neagh Basin

NASA Astrophysics Data System (ADS)

Vozar, J.; Moorkamp, M.; Jones, A. G.; Rath, V.; Muller, M. R.

2015-12-01

Multi-dimensional modelling of geophysical data collected in the Lough Neagh Basin is presented in the frame of the IRETHERM project. The Permo-Triassic Lough Neagh Basin, situated in the southeastern part of Northern Ireland, exhibits elevated geothermal gradient (~30 °C/km) in the exploratory drilled boreholes. This is taken to indicate good geothermal exploitation potential in the Sherwood Sandstone aquifer for heating, and possibly even electricity production, purposes. We have used a 3-D joint inversion framework for modelling the magnetotelluric (MT) and gravity data collected to the north of the Lough Neagh to derive robust subsurface geological models. Comprehensive supporting geophysical and geological data (e.g. borehole logs and reflection seismic images) have been used in order to analyze and model the MT and gravity data. The geophysical data sets were provided by the Geological Survey of Northern Ireland (GSNI). Considering correct objective function weighting in favor of noise-free MT response functions is particularly important in joint inversion. There is no simple way how to correct distortion effects the 3-D responses as can be done in 1-D or 2-D case. We have used the Tellus Project airborne EM data to constrain magnetotelluric data and correct them for near surface effects. The shallow models from airborne data are used to constrain the uppermost part of 3-D inversion model. Preliminary 3-D joint inversion modeling reveals that the Sherwood Sandstone Group and the Permian Sandstone Formation are imaged as a conductive zone at the depth range of 500 m to 2000 m with laterally varying thickness, depth, and conductance. The conductive target sediments become shallower and thinner to the north and they are laterally continuous. To obtain better characterization of thermal transport properties of investigated area we used porosity and resistivity data from the Annaghmore and Ballymacilroy boreholes to estimate the relations between porosity/permeability and electrical conductivity. The formulae are based on generalized Archie's law for multiple phases. The conductive layers are interpreted as water bearing or geothermal fluids and estimated porosity and permeability indicates potential to act as geothermal aquifer.

Hydraulic characterization of volcanic rocks in Pahute Mesa using an integrated analysis of 16 multiple-well aquifer tests, Nevada National Security Site, 2009–14

USGS Publications Warehouse

Garcia, C. Amanda; Jackson, Tracie R.; Halford, Keith J.; Sweetkind, Donald S.; Damar, Nancy A.; Fenelon, Joseph M.; Reiner, Steven R.

2017-01-20

An improved understanding of groundwater flow and radionuclide migration downgradient from underground nuclear-testing areas at Pahute Mesa, Nevada National Security Site, requires accurate subsurface hydraulic characterization. To improve conceptual models of flow and transport in the complex hydrogeologic system beneath Pahute Mesa, the U.S. Geological Survey characterized bulk hydraulic properties of volcanic rocks using an integrated analysis of 16 multiple-well aquifer tests. Single-well aquifer-test analyses provided transmissivity estimates at pumped wells. Transmissivity estimates ranged from less than 1 to about 100,000 square feet per day in Pahute Mesa and the vicinity. Drawdown from multiple-well aquifer testing was estimated and distinguished from natural fluctuations in more than 200 pumping and observation wells using analytical water-level models. Drawdown was detected at distances greater than 3 miles from pumping wells and propagated across hydrostratigraphic units and major structures, indicating that neither faults nor structural blocks noticeably impede or divert groundwater flow in the study area.Consistent hydraulic properties were estimated by simultaneously interpreting drawdown from the 16 multiple-well aquifer tests with an integrated groundwater-flow model composed of 11 well-site models—1 for each aquifer test site. Hydraulic properties were distributed across volcanic rocks with the Phase II Pahute Mesa-Oasis Valley Hydrostratigraphic Framework Model. Estimated hydraulic-conductivity distributions spanned more than two orders of magnitude in hydrostratigraphic units. Overlapping hydraulic conductivity ranges among units indicated that most Phase II Hydrostratigraphic Framework Model units were not hydraulically distinct. Simulated total transmissivity ranged from 1,600 to 68,000 square feet per day for all pumping wells analyzed. High-transmissivity zones exceeding 10,000 square feet per day exist near caldera margins and extend along the northern and eastern Pahute Mesa study area and near the southwestern edge of the study area. The estimated hydraulic-property distributions and observed hydraulic connections among geologic structures improved the characterization and representation of groundwater flow at Pahute Mesa.

Development of a globally applicable model for near real-time prediction of seismically induced landslides

USGS Publications Warehouse

Nowicki, M. Anna; Wald, David J.; Hamburger, Michael W.; Hearne, Mike; Thompson, Eric M.

2014-01-01

Substantial effort has been invested to understand where seismically induced landslides may occur in the future, as they are a costly and frequently fatal threat in mountainous regions. The goal of this work is to develop a statistical model for estimating the spatial distribution of landslides in near real-time around the globe for use in conjunction with the U.S. Geological Survey (USGS) Prompt Assessment of Global Earthquakes for Response (PAGER) system. This model uses standardized outputs of ground shaking from the USGS ShakeMap Atlas 2.0 to develop an empirical landslide probability model, combining shaking estimates with broadly available landslide susceptibility proxies, i.e., topographic slope, surface geology, and climate parameters. We focus on four earthquakes for which digitally mapped landslide inventories and well-constrainedShakeMaps are available. The resulting database is used to build a predictive model of the probability of landslide occurrence. The landslide database includes the Guatemala (1976), Northridge (1994), Chi-Chi (1999), and Wenchuan (2008) earthquakes. Performance of the regression model is assessed using statistical goodness-of-fit metrics and a qualitative review to determine which combination of the proxies provides both the optimum prediction of landslide-affected areas and minimizes the false alarms in non-landslide zones. Combined with near real-time ShakeMaps, these models can be used to make generalized predictions of whether or not landslides are likely to occur (and if so, where) for earthquakes around the globe, and eventually to inform loss estimates within the framework of the PAGER system.

The integration of palaeogeography and tectonics in refining plate tectonic models: an example from SE Asia

NASA Astrophysics Data System (ADS)

Masterton, S. M.; Markwick, P.; Bailiff, R.; Campanile, D.; Edgecombe, E.; Eue, D.; Galsworthy, A.; Wilson, K.

2012-04-01

Our understanding of lithospheric evolution and global plate motions throughout the Earth's history is based largely upon detailed knowledge of plate boundary structures, inferences about tectonic regimes, ocean isochrons and palaeomagnetic data. Most currently available plate models are either regionally restricted or do not consider palaeogeographies in their construction. Here, we present an integrated methodology in which derived hypotheses have been further refined using global and regional palaeogeographic, palaeotopological and palaeobathymetric maps. Iteration between our self-consistent and structurally constrained global plate model and palaeogeographic interpretations which are built on these reconstructions, allows for greater testing and refinement of results. Our initial structural and tectonic interpretations are based largely on analysis of our extensive global database of gravity and magnetic potential field data, and are further constrained by seismic, SRTM and Landsat data. This has been used as the basis for detailed interpretations that have allowed us to compile a new global map and database of structures, crustal types, plate boundaries and basin definitions. Our structural database is used in the identification of major tectonic terranes and their relative motions, from which we have developed our global plate model. It is subject to an ongoing process of regional evaluation and revisions in an effort to incorporate and reflect new tectonic and geologic interpretations. A major element of this programme is the extension of our existing plate model (GETECH Global Plate Model V1) back to the Neoproterozic. Our plate model forms the critical framework upon which palaeogeographic and palaeotopographic reconstructions have been made for every time stage in the Cretaceous and Cenozoic. Generating palaeogeographies involves integration of a variety of data, such as regional geology, palaeoclimate analyses, lithology, sea-level estimates, thermo-mechanical events and regional tectonics. These data are interpreted to constrain depositional systems and tectonophysiographic terranes. Palaeotopography and palaeobathymetry are derived from these tectonophysiographic terranes and depositional systems, and are further constrained using geological relationships, thermochronometric data, palaeoaltimetry indicators and modern analogues. Throughout this process, our plate model is iteratively tested against our palaeogeographies and their environmental consequences. Both the plate model and the palaeogeographies are refined until we have obtained a consistent and scientifically robust result. In this presentation we show an example from Southeast Asia, where the plate model complexity and wide variation in hypotheses has huge implications for the palaeogeographic interpretation, which can then be tested using geological observations from well and seismic data. For example, the Khorat Plateau Basin, Northeastern Thailand, comprises a succession of fluvial clastics during the Cretaceous, which include the evaporites of the Maha Sarakham Formation. These have been variously interpreted as indicative of saline lake or marine incursion depositional environments. We show how the feasibility of these different hypotheses is dependent on the regional palaeogeography (whether a marine link is possible), which in turn depends on the underlying plate model. We show two models with widely different environmental consequences. A more robust model that takes into account all these consequences, as well as data, can be defined by iterating through the consequences of the plate model and geological observations.

A theoretical framework for modeling dilution enhancement of non-reactive solutes in heterogeneous porous media.

PubMed

de Barros, F P J; Fiori, A; Boso, F; Bellin, A

2015-01-01

Spatial heterogeneity of the hydraulic properties of geological porous formations leads to erratically shaped solute clouds, thus increasing the edge area of the solute body and augmenting the dilution rate. In this study, we provide a theoretical framework to quantify dilution of a non-reactive solute within a steady state flow as affected by the spatial variability of the hydraulic conductivity. Embracing the Lagrangian concentration framework, we obtain explicit semi-analytical expressions for the dilution index as a function of the structural parameters of the random hydraulic conductivity field, under the assumptions of uniform-in-the-average flow, small injection source and weak-to-mild heterogeneity. Results show how the dilution enhancement of the solute cloud is strongly dependent on both the statistical anisotropy ratio and the heterogeneity level of the porous medium. The explicit semi-analytical solution also captures the temporal evolution of the dilution rate; for the early- and late-time limits, the proposed solution recovers previous results from the literature, while at intermediate times it reflects the increasing interplay between large-scale advection and local-scale dispersion. The performance of the theoretical framework is verified with high resolution numerical results and successfully tested against the Cape Cod field data. Copyright © 2015 Elsevier B.V. All rights reserved.

A multiple-point geostatistical approach to quantifying uncertainty for flow and transport simulation in geologically complex environments

NASA Astrophysics Data System (ADS)

Cronkite-Ratcliff, C.; Phelps, G. A.; Boucher, A.

2011-12-01

In many geologic settings, the pathways of groundwater flow are controlled by geologic heterogeneities which have complex geometries. Models of these geologic heterogeneities, and consequently, their effects on the simulated pathways of groundwater flow, are characterized by uncertainty. Multiple-point geostatistics, which uses a training image to represent complex geometric descriptions of geologic heterogeneity, provides a stochastic approach to the analysis of geologic uncertainty. Incorporating multiple-point geostatistics into numerical models provides a way to extend this analysis to the effects of geologic uncertainty on the results of flow simulations. We present two case studies to demonstrate the application of multiple-point geostatistics to numerical flow simulation in complex geologic settings with both static and dynamic conditioning data. Both cases involve the development of a training image from a complex geometric description of the geologic environment. Geologic heterogeneity is modeled stochastically by generating multiple equally-probable realizations, all consistent with the training image. Numerical flow simulation for each stochastic realization provides the basis for analyzing the effects of geologic uncertainty on simulated hydraulic response. The first case study is a hypothetical geologic scenario developed using data from the alluvial deposits in Yucca Flat, Nevada. The SNESIM algorithm is used to stochastically model geologic heterogeneity conditioned to the mapped surface geology as well as vertical drill-hole data. Numerical simulation of groundwater flow and contaminant transport through geologic models produces a distribution of hydraulic responses and contaminant concentration results. From this distribution of results, the probability of exceeding a given contaminant concentration threshold can be used as an indicator of uncertainty about the location of the contaminant plume boundary. The second case study considers a characteristic lava-flow aquifer system in Pahute Mesa, Nevada. A 3D training image is developed by using object-based simulation of parametric shapes to represent the key morphologic features of rhyolite lava flows embedded within ash-flow tuffs. In addition to vertical drill-hole data, transient pressure head data from aquifer tests can be used to constrain the stochastic model outcomes. The use of both static and dynamic conditioning data allows the identification of potential geologic structures that control hydraulic response. These case studies demonstrate the flexibility of the multiple-point geostatistics approach for considering multiple types of data and for developing sophisticated models of geologic heterogeneities that can be incorporated into numerical flow simulations.

The interpretation of crustal dynamics data in terms of plate interactions and active tectonics of the Anatolian Plate and surrounding regions in the Middle East

NASA Technical Reports Server (NTRS)

Toksoz, M. Nafi

1987-01-01

The long term objective of this project is to interpret NASA's Crustal Dynamics measurements (SLR) in the Eastern Mediterranean region in terms of relative plate motions and intraplate deformation. The approach is to combine realistic modeling studies with an analysis of available geophysical and geological observations to provide a framework for interpreting NASA's measurements. This semi-annual report concentrates on recent results regarding the tectonics of Anatolia and surrounding regions from ground based observations. Also briefly reported on is progress made in using GPS measurements to densify SLR observations in the Eastern Mediterranean.

Geologic framework for the national assessment of carbon dioxide storage resources: Columbia Basin of Oregon, Washington, and Idaho, and the Western Oregon-Washington basins: Chapter D in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Covault, Jacob A.; Blondes, Madalyn S.; Cahan, Steven M.; DeVera, Christina A.; Freeman, P.A.; Lohr, Celeste D.; Warwick, Peter D.; Corum, Margo D.

2013-01-01

The 2007 Energy Independence and Security Act (Public Law 110–140) directs the U.S. Geological Survey (USGS) to conduct a national assessment of potential geologic storage resources for carbon dioxide (CO2). The methodology used by the USGS for the national CO2 assessment follows that of previous USGS work. The methodology is non-economic and intended to be used at regional to subbasinal scales. This report identifies and contains geologic descriptions of three storage assessment units (SAUs) in Eocene and Oligocene sedimentary rocks within the Columbia, Puget, Willapa, Astoria, Nehalem, and Willamette Basins of Oregon, Washington, and Idaho, and focuses on the characteristics, specified in the methodology, that influence the potential CO2 storage resource in those SAUs. Specific descriptions of the SAU boundaries as well as their sealing and reservoir units are included. Properties for each SAU, such as depth to top, gross thickness, porosity, permeability, groundwater quality, and structural reservoir traps, are provided to illustrate geologic factors critical to the assessment. The designated sealing unit in the Columbia Basin is tentatively chosen to be the ubiquitous and thick Miocene Columbia River Basalt Group. As a result of uncertainties regarding the seal integrity of the Columbia River Basalt Group, the SAUs were not quantitatively assessed. Figures in this report show SAU boundaries and cell maps of well penetrations through sealing units into the top of the storage formations. The cell maps show the number of penetrating wells within one square mile and are derived from interpretations of incompletely attributed well data, a digital compilation that is known not to include all drilling. The USGS does not expect to know the location of all wells and cannot guarantee the amount of drilling through specific formations in any given cell shown on the cell maps.

A Hydrostratigraphic Model and Alternatives for the Groundwater Flow and Contaminant Transport Model of Corrective Action Unit 97: Yucca Flat-Climax Mine, Lincoln and Nye Counties, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geotechnical Sciences Group Bechtel Nevada

2006-01-01

A new three-dimensional hydrostratigraphic framework model for the Yucca Flat-Climax Mine Corrective Action Unit was completed in 2005. The model area includes Yucca Flat and Climax Mine, former nuclear testing areas at the Nevada Test Site, and proximal areas. The model area is approximately 1,250 square kilometers in size and is geologically complex. Yucca Flat is a topographically closed basin typical of many valleys in the Basin and Range province. Faulted and tilted blocks of Tertiary-age volcanic rocks and underlying Proterozoic and Paleozoic sedimentary rocks form low ranges around the structural basin. During the Cretaceous Period a granitic intrusive wasmore » emplaced at the north end of Yucca Flat. A diverse set of geological and geophysical data collected over the past 50 years was used to develop a structural model and hydrostratigraphic system for the basin. These were integrated using EarthVision? software to develop the 3-dimensional hydrostratigraphic framework model. Fifty-six stratigraphic units in the model area were grouped into 25 hydrostratigraphic units based on each unit's propensity toward aquifer or aquitard characteristics. The authors organized the alluvial section into 3 hydrostratigraphic units including 2 aquifers and 1 confining unit. The volcanic units in the model area are organized into 13 hydrostratigraphic units that include 8 aquifers and 5 confining units. The underlying pre-Tertiary rocks are divided into 7 hydrostratigraphic units, including 3 aquifers and 4 confining units. Other units include 1 Tertiary-age sedimentary confining unit and 1 Mesozoic-age granitic confining unit. The model depicts the thickness, extent, and geometric relationships of these hydrostratigraphic units (''layers'' in the model) along with the major structural features (i.e., faults). The model incorporates 178 high-angle normal faults of Tertiary age and 2 low-angle thrust faults of Mesozoic age. The complexity of the model area and the non-uniqueness of some of the interpretations incorporated into the base model made it necessary to formulate alternative interpretations for some of the major features in the model. Five of these alternatives were developed so they could be modeled in the same fashion as the base model. This work was done for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office in support of the Underground Test Area subproject of the Environmental Restoration Project.« less

The Pilot Lunar Geologic Mapping Project: Summary Results and Recommendations from the Copernicus Quadrangle

NASA Technical Reports Server (NTRS)

Skinner, J. A., Jr.; Gaddis, L. R.; Hagerty, J. J.

2010-01-01

The first systematic lunar geologic maps were completed at 1:1M scale for the lunar near side during the 1960s using telescopic and Lunar Orbiter (LO) photographs [1-3]. The program under which these maps were completed established precedents for map base, scale, projection, and boundaries in order to avoid widely discrepant products. A variety of geologic maps were subsequently produced for various purposes, including 1:5M scale global maps [4-9] and large scale maps of high scientific interest (including the Apollo landing sites) [10]. Since that time, lunar science has benefitted from an abundance of surface information, including high resolution images and diverse compositional data sets, which have yielded a host of topical planetary investigations. The existing suite of lunar geologic maps and topical studies provide exceptional context in which to unravel the geologic history of the Moon. However, there has been no systematic approach to lunar geologic mapping since the flight of post-Apollo scientific orbiters. Geologic maps provide a spatial and temporal framework wherein observations can be reliably benchmarked and compared. As such, a lack of a systematic mapping program means that modern (post- Apollo) data sets, their scientific ramifications, and the lunar scientists who investigate these data, are all marginalized in regard to geologic mapping. Marginalization weakens the overall understanding of the geologic evolution of the Moon and unnecessarily partitions lunar research. To bridge these deficiencies, we began a pilot geologic mapping project in 2005 as a means to assess the interest, relevance, and technical methods required for a renewed lunar geologic mapping program [11]. Herein, we provide a summary of the pilot geologic mapping project, which focused on the geologic materials and stratigraphic relationships within the Copernicus quadrangle (0-30degN, 0-45degW).

Methane on the Move: natural greenhouse gas emissions over geological time

NASA Astrophysics Data System (ADS)

Horsfield, B.; di Primio, R.; Kroeger, K. F.; Schicks, J. M.

2008-12-01

The mass of organic carbon in sedimentary basins amounts to a staggering 1016 tons, dwarfing the mass contained in coal, oil, gas and all living systems by ten thousand-fold. The changing fate of this giant mass during subsidence and uplift, via chemical, physical and biological processes, is known to ultimately control fossil energy resource occurrence worldwide. But what has been overlooked and/or ignored until now is its enormous capacity for driving global climate: only a tiny degree of leakage, particularly when focussed through the clathrate cycle, can result in high greenhouse gas emissions. Understanding the workings of sedimentary basins in time and space is fundamental to gaining insights into Earth's climate. Here we shall present an integrated framework based on petroleum system modelling that will ultimately quantify methane migration and emission from one hundred of the world's most prolific petroliferous sedimentary basins. Timing of hydrocarbon generation from globally occurring prolific Jurassic and Cretaceous source rocks is regarded to be the key factor in quantifying gas release. Combined thermogenic and biogenic methane fluxes are the base for prediction of gas hydrate formation through time and space, by application of kinetics developed in the laboratory to geological scenarios. Results are calibrated in basin scale by emission structure evaluation (mud volcanoes, carbonate mounds, pockmarks) and on a global scale by proxy data from sedimentary archives and local atmospheric data. Identifying potential climate feedback processes over a geological time line that spans the Cenozoic requires a comprehensive understanding of source-sink relationships by coupling these feedstock fluxes with gas hydrate stability considerations, deep biosphere activity, ocean and atmosphere modelling

Magnetotelluric data collected near geophysically logged boreholes in the Espa?ola and Middle Rio Grande basins, New Mexico

USGS Publications Warehouse

Williams, Jackie M.; Rodriguez, Brian D.

2006-01-01

The Santa Fe region is growing rapidly. The Santa Fe Group aquifer in the Espa?ola Basin is the main source of municipal water for the region, and water shortfalls could have serious consequences. Future growth and land management in the region depend on accurate assessment and protection of the region's ground-water resources. An important issue in managing the ground-water resources is a better understanding of the hydrogeology of the Tertiary Santa Fe Group. The Santa Fe Group includes the sedimentary deposits that fill the Rio Grande rift and contain the principal ground-water aquifers. The U.S. Geological Survey (USGS) is conducting a series of multidisciplinary studies of the Espa?ola Basin in northern New Mexico. Detailed geologic mapping, high-resolution airborne magnetic surveys, electromagnetic surveys, and hydrologic, lithologic, and hydro-geochemical data are being used to better understand the aquifer systems. Magnetotelluric (MT) surveys were completed as part of these studies. The primary purpose of the MT surveys was to map changes in electrical resistivity with depth that are related to differences in various rock types that help control the properties of aquifers in the region. Resistivity modeling of the MT data can be used to investigate buried structures related to the basic geologic framework of the study area. The purpose of this report is to release MT sounding data collected near geophysically logged boreholes in the study area, including the nearby Middle Rio Grande Basin. This MT data can be used in subsequent resistivity modeling. No interpretation of the data is included in this report.

Executive Summary -- assessment of undiscovered oil and gas resources of the San Joaquin Basin Province of California, 2003: Chapter 1 in Petroleum systems and geologic assessment of oil and gas in the San Joaquin Basin Province, California

USGS Publications Warehouse

Gautier, Donald L.; Scheirer, Allegra Hosford; Tennyson, Marilyn E.; Peters, Kenneth E.; Magoon, Leslie B.; Lillis, Paul G.; Charpentier, Ronald R.; Cook, Troy A.; French, Christopher D.; Klett, Timothy R.; Pollastro, Richard M.; Schenk, Christopher J.

2007-01-01

In 2003, the U.S. Geological Survey (USGS) completed an assessment of the oil and gas resource potential of the San Joaquin Basin Province of California (fig. 1.1). The assessment is based on the geologic elements of each Total Petroleum System defined in the province, including hydrocarbon source rocks (source-rock type and maturation and hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). Using this geologic framework, the USGS defined five total petroleum systems and ten assessment units within these systems. Undiscovered oil and gas resources were quantitatively estimated for the ten assessment units (table 1.1). In addition, the potential was estimated for further growth of reserves in existing oil fields of the San Joaquin Basin.

Shallow geology, seafloor texture, and physiographic zones of the Inner Continental Shelf from Nahant to northern Cape Cod Bay, Massachusetts

USGS Publications Warehouse

Pendleton, Elizabeth A.; Baldwin, Wayne E.; Barnhardt, Walter A.; Ackerman, Seth D.; Foster, David S.; Andrews, Brian D.; Schwab, William C.

2013-01-01

The Massachusetts inner continental shelf between Nahant and northern Cape Cod Bay has been profoundly affected by the occupation and retreat of glacial ice sheets and relative sea-level change during the Quaternary. Marine geologic mapping of this area is a component of a statewide cooperative effort involving the U.S. Geological Survey and the Massachusetts Office of Coastal Zone Management. Interpretation of high-resolution geophysical data (interferometric and multibeam swath bathymetry, lidar, backscatter, and seismic reflection), sediment samples, and bottom photographs was used to produce a series of maps that describe the distribution and texture of seafloor sediments, shallow geologic framework, and physiographic zones of this inner-shelf region. These data and interpretations are intended to aid efforts to inventory and manage coastal and marine resources, and provide baseline information for research focused on coastal evolution and environmental change.

The intercrater plains of Mercury and the Moon: Their nature, origin and role in terrestrial planet evolution. Geologic mapping of Mercury and the Moon. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Leake, M. A.

1982-01-01

The geologic framework of the intercrater plains on Mercury and the Moon as determined through geologic mapping is presented. The strategies used in such mapping are discussed first. Then, because the degree of crater degradation is applied to both mapping and crater statistics, the correlation of degradation classification of lunar and Mercurian craters is thoroughly addressed. Different imaging systems can potentially affect this classification, and are therefore also discussed. The techniques used in mapping Mercury are discussed in Section 2, followed by presentation of the Geologic Map of Mercury in Section 3. Material units, structures, and relevant albedo and color data are discussed therein. Preliminary conclusions regarding plains' origins are given there. The last section presents the mapping analyses of the lunar intercrater plains, including tentative conclusions of their origin.

Geological mapping goes 3-D in response to societal needs

USGS Publications Warehouse

Thorleifson, H.; Berg, R.C.; Russell, H.A.J.

2010-01-01

The transition to 3-D mapping has been made possible by technological advances in digital cartography, GIS, data storage, analysis, and visualization. Despite various challenges, technological advancements facilitated a gradual transition from 2-D maps to 2.5-D draped maps to 3-D geological mapping, supported by digital spatial and relational databases that can be interrogated horizontally or vertically and viewed interactively. Challenges associated with data collection, human resources, and information management are daunting due to their resource and training requirements. The exchange of strategies at the workshops has highlighted the use of basin analysis to develop a process-based predictive knowledge framework that facilitates data integration. Three-dimensional geological information meets a public demand that fills in the blanks left by conventional 2-D mapping. Two-dimensional mapping will, however, remain the standard method for extensive areas of complex geology, particularly where deformed igneous and metamorphic rocks defy attempts at 3-D depiction.

Tectonic evaluation of the Nubian shield of Northeastern Sudan using thematic mapper imagery

NASA Technical Reports Server (NTRS)

1986-01-01

Bechtel is nearing completion of a one-year program that uses digitally enhanced LANDSAT Thematic Mapper (TM) data to compile the first comprehensive regional tectonic map of the Proterozoic Nubian Shield exposed in the northern Red Sea Hills of northeastern Sudan. The status of significant objectives of this study are given. Pertinent published and unpublished geologic literature and maps of the northern Red Sea Hills to establish the geologic framework of the region were reviewed. Thematic mapper imagery for optimal base-map enhancements was processed. Photo mosaics of enhanced images to serve as base maps for compilation of geologic information were completed. Interpretation of TM imagery to define and delineate structural and lithogologic provinces was completed. Geologic information (petrologic, and radiometric data) was compiled from the literature review onto base-map overlays. Evaluation of the tectonic evolution of the Nubian Shield based on the image interpretation and the compiled tectonic maps is continuing.

Geological Implications of a Physical Libration on Enceladus

NASA Technical Reports Server (NTRS)

Hurford, T. A.; Bills, B. G.; Helfenstein, P.; Greenberg, R.; Hoppa, G. V.; Hamilton, D. P.

2008-01-01

Given the non-spherical shape of Enceladus (Thomas et al., 2007), the satellite will experience gravitational torques that will cause it to physically librate as it orbits Saturn. Physical libration would produce a diurnal oscillation in the longitude of Enceladus tidal bulge which, could have a profound effect on the diurnal stresses experienced by the surface of the satellite. Although Cassini ISS has placed an observational upper limit on Enceladus libration amplitude of F < 1.5deg (Porco et al., 2006), smaller amplitudes can still have geologically significant consequences. Here we present the first detailed description of how physical libration affects tidal stresses and how those stresses then might affect geological processes including crack formation and propagation, south polar eruption activity, and tidal heating. Our goal is to provide a framework for testing the hypothesis that geologic features on Enceladus are produced by tidal stresses from diurnal physical and optical librations of the satellite.

Probabilistic prediction models for aggregate quarry siting

USGS Publications Warehouse

Robinson, G.R.; Larkins, P.M.

2007-01-01

Weights-of-evidence (WofE) and logistic regression techniques were used in a GIS framework to predict the spatial likelihood (prospectivity) of crushed-stone aggregate quarry development. The joint conditional probability models, based on geology, transportation network, and population density variables, were defined using quarry location and time of development data for the New England States, North Carolina, and South Carolina, USA. The Quarry Operation models describe the distribution of active aggregate quarries, independent of the date of opening. The New Quarry models describe the distribution of aggregate quarries when they open. Because of the small number of new quarries developed in the study areas during the last decade, independent New Quarry models have low parameter estimate reliability. The performance of parameter estimates derived for Quarry Operation models, defined by a larger number of active quarries in the study areas, were tested and evaluated to predict the spatial likelihood of new quarry development. Population density conditions at the time of new quarry development were used to modify the population density variable in the Quarry Operation models to apply to new quarry development sites. The Quarry Operation parameters derived for the New England study area, Carolina study area, and the combined New England and Carolina study areas were all similar in magnitude and relative strength. The Quarry Operation model parameters, using the modified population density variables, were found to be a good predictor of new quarry locations. Both the aggregate industry and the land management community can use the model approach to target areas for more detailed site evaluation for quarry location. The models can be revised easily to reflect actual or anticipated changes in transportation and population features. ?? International Association for Mathematical Geology 2007.

Geologic framework and hydrogeologic characteristics in the southern part of the Rancho Diana Natural Area, northern Bexar County, Texas, 2008-10

USGS Publications Warehouse

Clark, Allan K.; Morris, Robert R.

2011-01-01

The area designated by the city of San Antonio as the Rancho Diana Natural Area is in northern Bexar County, near San Antonio, Texas. During 2008-10, the U.S. Geological Survey, in cooperation with the city of San Antonio, documented the geologic framework and mapped the hydrogeologic characteristics for the southern part of the Rancho Diana Natural Area. The geologic framework of the study area and its hydrogeologic characteristics were documented using field observations and information from previously published reports. Many of the geologic and hydrogeologic features were found by making field observations through the dense vegetation along gridlines spaced approximately 25 feet apart and documenting the features as they were located. Surface geologic features were identified and hydrogeologic features such as caves, sinkholes, and areas of solutionally enlarged porosity were located using hand-held Global Positioning System units. The location data were used to create a map of the hydrogeologic subdivisions and the location of karst features. The outcrops of the Edwards and Trinity aquifer recharge zones were mapped by using hydrogeologic subdivisions modified from previous reports. All rocks exposed within the study area are of sedimentary origin and Lower Cretaceous in age. The valley floor is formed in the cavernous member of the upper Glen Rose Limestone of the Trinity Group. The hills are composed of the basal nodular member, dolomitic member, Kirschberg evaporite member, and grainstone member of the Kainer Formation of the Edwards Group. Field observations made during this study of the exposed formations and members indicate that the formations and members typically are composed of mudstones, wackestones, packstones, grainstones, and argillaceous limestones, along with marls. The upper Glen Rose Limestone is approximately 410 to 450 feet thick but only the upper 70 feet is exposed in the study area. The Kainer Formation is approximately 255 feet thick in the study area and is composed of, in ascending order, the basal nodular member, dolomitic member, Kirschberg evaporite member, and grainstone member. The Edwards and Trinity aquifers contain a combination of fabric-selective and not-fabric-selective porosities. Porosity types observed in the study area that can increase the effective porosity and increase permeability include solutionally enlarged caves, sinkholes, fractures, bedding planes, channels, molds and vugs. Caves found during hydrogeologic mapping might have been spring discharge points, but sufficient downcutting over geologic time in the rocks has occurred so that springs discharge at lower elevations near the creek channel. The mapped caves, sinkholes, and other areas of solutionally enlarged porosity might facilitate recharge during large storm events when runoff occurs on the hillsides; additional areally distributed recharge in the study area occurs as a result of infiltration.

Geologic framework of the offshore region adjacent to Delaware

USGS Publications Warehouse

Benson, R.N.; Roberts, J.H.

1989-01-01

Several multichannel, common depth point (CDP) seismic reflection profiles concentrated in the area of the entrance to Delaware Bay provide a tie between the known onshore geology of the Coastal Plain of Delaware and the offshore geology of the Baltimore Canyon Trough. The data provide a basis for understanding the geologic framework and petroleum resource potential of the area immediately offshore Delaware. Our research has focused on buried early Mesozoic rift basins and their geologic history. Assuming that the buried basins are analogous to the exposed Newark Supergroup basins of Late Triassic-Early Jurassic age, the most likely possibility for occurrence of hydrocarbon source beds in the area of the landward margin of the Baltimore Canyon Trough is presumed to be lacustrine, organic-rich shales probably present in the basins. Although buried basins mapped offshore Delaware are within reach of drilling, no holes have been drilled to date; therefore, direct knowledge of source, reservoir, and sealing beds is absent. Buried rift basins offshore Delaware show axial trends ranging from NW-SE to NNE-SSW. Seismic reflection profiles are too widely spaced to delineate basin boundaries accurately. Isopleths of two-way travel time representing basin fill suggest that, structurally, the basins are grabens and half-grabens. As shown on seismic reflection profiles, bounding faults of the basins intersect or merge with low-angle fault surfaces that cut the pre-Mesozoic basement. The rift basins appear to have formed by Mesozoic extension that resulted in reverse motion on reactivated basement thrust faults that originated from compressional tectonics during the Paleozoic. Computer-plotted structure contour maps derived from analysis of seismic reflection profiles provide information on the burial history of the rift basins. The postrift unconformity bevels the rift basins and, in the offshore area mapped, ranges from 2000 to 12,000 m below present sea level. The oldest postrift sediments that cover the more deeply buried rift basins are estimated to be of Middle Jurassic age (Bajocian-Bathonian), the probable time of opening of the Atlantic Ocean basin and onset of continental drift about 175-180 m.y. ago. By late Oxfordian-early Kimmeridgian time, the less deeply buried basins nearshore Delaware had been covered. A time-temperature index of maturity plot of one of the basins indicates that only dry gas would be present in reservoirs in synrift rocks buried by more than 6000 m of postrift sediments and in the oldest (Bathonian?-Callovian?) postrift rocks. Less deeply buried synrift rocks landward of the basin modeled might still be within the oil generation window. ?? 1989.

A Corner-Point-Grid-Based Voxelization Method for Complex Geological Structure Model with Folds

NASA Astrophysics Data System (ADS)

Chen, Qiyu; Mariethoz, Gregoire; Liu, Gang

2017-04-01

3D voxelization is the foundation of geological property modeling, and is also an effective approach to realize the 3D visualization of the heterogeneous attributes in geological structures. The corner-point grid is a representative data model among all voxel models, and is a structured grid type that is widely applied at present. When carrying out subdivision for complex geological structure model with folds, we should fully consider its structural morphology and bedding features to make the generated voxels keep its original morphology. And on the basis of which, they can depict the detailed bedding features and the spatial heterogeneity of the internal attributes. In order to solve the shortage of the existing technologies, this work puts forward a corner-point-grid-based voxelization method for complex geological structure model with folds. We have realized the fast conversion from the 3D geological structure model to the fine voxel model according to the rule of isocline in Ramsay's fold classification. In addition, the voxel model conforms to the spatial features of folds, pinch-out and other complex geological structures, and the voxels of the laminas inside a fold accords with the result of geological sedimentation and tectonic movement. This will provide a carrier and model foundation for the subsequent attribute assignment as well as the quantitative analysis and evaluation based on the spatial voxels. Ultimately, we use examples and the contrastive analysis between the examples and the Ramsay's description of isoclines to discuss the effectiveness and advantages of the method proposed in this work when dealing with the voxelization of 3D geologic structural model with folds based on corner-point grids.

Critical Zone Science as a Multidisciplinary Framework for Teaching Earth Science and Sustainability

NASA Astrophysics Data System (ADS)

Wymore, A.; White, T. S.; Dere, A. L. D.; Hoffman, A.; Washburne, J. C.; Conklin, M. H.

2016-12-01

The Earth's Critical Zone (CZ) is the terrestrial portion of the continents ranging from the top of the vegetative canopy down through soil and bedrock to the lowest extent of freely circulating groundwater. The primary objective of CZ science is to characterize and understand how the reciprocal interactions among rock, soil, water, air and terrestrial organisms influence the Earth as a habitable environment. Thus it is a highly multidisciplinary science that incorporates the biological, hydrological, geological and atmospheric sciences and provides a holistic approach to teaching Earth system science. Here we share highlights from a full-semester university curriculum that introduces upper-division Environmental Science, Geology, Hydrology and Earth Science students to CZ science. We emphasize how a CZ framework is appropriate to teach concepts across the scientific disciplines, concepts of sustainability, and how CZ science serves as a useful approach to solving humanities' grand challenges.

Modeled historical land use and land cover for the conterminous United States

USGS Publications Warehouse

Sohl, Terry L.; Reker, Ryan R.; Bouchard, Michelle A.; Sayler, Kristi L.; Dornbierer, Jordan; Wika, Steve; Quenzer, Robert; Friesz, Aaron M.

2016-01-01

The landscape of the conterminous United States has changed dramatically over the last 200 years, with agricultural land use, urban expansion, forestry, and other anthropogenic activities altering land cover across vast swaths of the country. While land use and land cover (LULC) models have been developed to model potential future LULC change, few efforts have focused on recreating historical landscapes. Researchers at the US Geological Survey have used a wide range of historical data sources and a spatially explicit modeling framework to model spatially explicit historical LULC change in the conterminous United States from 1992 back to 1938. Annual LULC maps were produced at 250-m resolution, with 14 LULC classes. Assessment of model results showed good agreement with trends and spatial patterns in historical data sources such as the Census of Agriculture and historical housing density data, although comparison with historical data is complicated by definitional and methodological differences. The completion of this dataset allows researchers to assess historical LULC impacts on a range of ecological processes.

The Dream

NASA Astrophysics Data System (ADS)

Peach, D.

2010-12-01

Models have become a routine research output over the past decade. They are used by many scientific disciplines in order to understand and analyses the processes and conditions within their domain of interest. This has resulted in a significant increase in scientific understanding and in a multitude of discipline specific models, modelling system software and workflows. There is now a growing realisation that to address the most pertinent questions of the age, such as climate change and the sustainable use of natural resources, we need to bringing together climate, ecological, hydrological, hydrogeological, geological and socio-economic models in order to provide the necessary framework to make truly informed decisions. At the British Geological Survey our vision is to provide scientists with the data, tools, techniques and support to address trans-disciplinary environmental questions impacting on human society. We hope to achieve this by being a leading member of an open community that will share data, applications and environmental models thus enabling collaboration and achieving sustainable solutions. The British Geological Survey has recently completed a scoping study with the aim of planning the implementation of the vision and preparing the organisation for the changes that are required to enable it to engage more effectively in trans-disciplinary modelling. This has resulted in the launch of a cross-cutting project call Data and Research for Environmental Applications and Models: The DREAM. The scoping study recognised that the investment and knowledge captured within the many existing scientific models represent a significant resource and not one that could be easily replicated in more centralised environmental modelling software. The only viable option in a ‘linked models’ approach which enables models to pass parameters between each other at runtime. This is perceived to be a pragmatic, achievable and cost-effective solution. This solution brings together the best and most appropriate scientific models and allows the various scientific disciplines to continue the development of their current models. The European Union has funded multi-national, multi-disciplinary research into ‘linked modelling’, using the Open Model Interchange (OPENMI) standard. This software used, in conjunction with critical underpinning activities such as data management, semantics and ontologies, understanding of uncertainty and visualisation, offers a rapidly maturing solution with the potential to fulfil The DREAM.

Challenges and Solutions for the Integration of Structural and Hydrogeological Understanding of Fracture Systems - Insights from the Olkiluoto Site, Finland

NASA Astrophysics Data System (ADS)

Hartley, L. J.; Aaltonen, I.; Baxter, S. J.; Cottrell, M.; Fox, A. L.; Hoek, J.; Koskinen, L.; Mattila, J.; Mosley, K.; Selroos, J. O.; Suikkanen, J.; Vanhanarkaus, O.; Williams, T. R. N.

2017-12-01

A field site at Olkiluoto in SW Finland has undergone extensive investigations as a location for a deep geological repository for spent nuclear fuel, which is expected to become operational in the early 2020s. Characterisation data comes from 58 deep cored drillholes, a wide variety of geophysical investigations, many outcrops, kilometres of underground mapping and testing in the ONKALO research facility, and groundwater pressure monitoring and sampling in both deep and shallow holes. A primary focus is on the properties of natural fractures and brittle fault zones in the low permeability crystalline rocks at Olkiluoto; an understanding of the flow and transport processes in these features are an essential part of assessing long-term safety of the repository. This presentation will illustrate how different types of source data and cross-disciplinary interpretations are integrated to develop conceptual and numerical models of the fracture system. A model of the brittle fault zones developed from geological and geophysical data provides the hydrostructural backbone controlling the most intense fracturing and dynamic conduits for fluids. Models of ductile deformation and lithology form a tectonic framework for the description of fracture heterogeneity in the background rock, revealing correlations between the intensity and orientation of fractures with geological and spatial properties. The sizes of brittle features are found to be best defined on two scales relating to individual fractures and zones. Inferred fracture-specific from flow logging are correlated with fracture geometric and mechanical properties along with in situ stress measurements to create a hydromechanical description of fracture hydraulic properties. The insights and understandings gained from these efforts help define a discrete fracture network (DFN) model for the Olkiluoto site, with hydrogeological characteristics consistent with monitoring data of hydraulic heads and their disturbances to pumping and underground construction. This work offers ideas and proposed solutions on how some of the challenges in describing fractured rock hydrogeology can be tackled.

Simulating CO2 Leakage and Seepage From Geologic Carbon Sequestration Sites: Implications for Near-Surface Monitoring

NASA Astrophysics Data System (ADS)

Oldenburg, C. M.; Lewicki, J. L.; Zhang, Y.

2003-12-01

The injection of CO2 into deep geologic formations for the purpose of carbon sequestration entails risk that CO2 will leak upward from the target formation and ultimately seep out of the ground surface. We have developed a coupled subsurface and atmospheric surface layer modeling capability based on TOUGH2 to simulate CO2 leakage and seepage. Simulation results for representative subsurface and surface layer conditions are used to specify the requirements of potential near-surface monitoring strategies relevant to both health, safety, and environmental risk assessment as well as sequestration verification. The coupled model makes use of the standard multicomponent and multiphase framework of TOUGH2 and extends the model domain to include an atmospheric surface layer. In the atmospheric surface layer, we assume a logarithmic velocity profile for the time-averaged wind and make use of Pasquill-Gifford and Smagorinski dispersion coefficients to model surface layer dispersion. Results for the unsaturated zone and surface layer show that the vadose zone pore space can become filled with pure CO2 even for small leakage fluxes, but that CO2 concentrations above the ground surface are very low due to the strong effects of dispersion caused by surface winds. Ecological processes such as plant photosynthesis and root respiration, as well as biodegradation in soils, strongly affect near-surface CO2 concentrations and fluxes. The challenge for geologic carbon sequestration verification is to discern the leakage and seepage signal from the ecological signal. Our simulations point to the importance of subsurface monitoring and the need for geochemical (e.g., isotopic) analyses to distinguish leaking injected fossil CO2 from natural ecological CO2. This work was supported by the Office of Science, U.S. Department of Energy under contract No. DE-AC03-76SF00098.

Geologic cross section E-E' through the Appalachian basin from the Findlay arch, Wood County, Ohio, to the Valley and Ridge province, Pendleton County, West Virginia: Chapter E.4.2 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ryder, Robert T.; Swezey, Christopher S.; Crangle, Robert D.; Trippi, Michael H.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

This chapter is a re-release of U.S. Geological Survey Scientific Investigations Map 2985, of the same title, by Ryder and others (2008). For this chapter, two appendixes have been added that do not appear with the original version. Appendix A provides Log ASCII Standard (LAS) files for each drill hole along cross-section E–E'; they are text files which encode gamma-ray, neutron, density, and other logs that can be used by most well-logging software. Appendix B provides graphic well-log traces from each drill hole.

Geologic map of the Western Grove quadrangle, northwestern Arkansas

USGS Publications Warehouse

Hudson, Mark R.; Turner, Kenzie J.; Repetski, John E.

2006-01-01

This map summarizes the geology of the Western Grove 7.5-minute quadrangle in northern Arkansas that is located on the southern flank of the Ozark dome, a late Paleozoic regional uplift. The exposed bedrock of this map area comprises approximately 1,000 ft of Ordovician and Mississippian carbonate and clastic sedimentary rocks that have been mildly folded and broken by faults. A segment of the Buffalo River loops through the southern part of the quadrangle, and the river and adjacent lands form part of Buffalo National River, a park administered by the U.S. National Park Service. This geologic map provides information to better understand the natural resources of the Buffalo River watershed, particularly its karst hydrogeologic framework.

4D Geomodeling: a Tool for Targeting New Potential Mineralization - Example of the Kupferschiefer in the Lubin Region, Poland

NASA Astrophysics Data System (ADS)

Mejia-Herrera, Pablo; Royer, Jean-Jacques; Fraboulet, Jean-Gabriel; Zielinska, Agata

2013-04-01

Understanding the history of sedimentary basins is of paramount importance for reconstituting oil and gas migration, but also in mineral exploration for identifying brine pathways. Advanced modeling technology such as 3&4D geomodeling can be fruitfully used to explore with new eyes old matured mining field. The Polish Kupferschiefers, a sediment-hosted polymetallic (Cu, Ag, Au, PGE) deposit, is one of the most important sources for copper and silver in the world. Within the framework of the ProMine European project, the Lubin region (south west of Poland), was selected for modeling in 3&4D the geological formations in order to better understand the distribution of the Cu-Ag mineralization, and possibly to define new potential targets. A regional scale 4D reconstitution of the North European basin was undertaken to better understand the burial, deformation and natural hydro-fracturing history of the Lubin Kupferschiefer. It comprises the creation of a 3D model of the present geological formation including more than 200 wells coming from the mining exploitation of the Kupferschiefer, cross sections from seismic exploration and geological maps. This 3D model has been then restored and decompacted using the Kine3D-2 Gocad plug-in. The PetroMode 1D was then used to reconstitute the temperatures, pressures, fluid overpressure, and oil and gas maturation during the burying history of the Southern-Western Poland basin. Conditions for hydraulic fracturing were identified within the base of the Zechstein shales, during an inversion phase at the Late Cretaceous-Early Paleocene time. This up-lifting yields the conditions for hydrothermal recirculation of mineralizing brines explaining the location of Cu (Cu-Fe) sulfides ores in the area. The low permeable Zechstein series (including evaporite, clays and marls) seem to have played an important role as an impermeable cover confining the hydrothermal fluids in the pre-Triassic series. The 4D restoring-decompacting modeling allows reconstituting the burial, deformation and natural hydro-fracturing history of intra-basin sediment-hosted ore deposits. In the Lubin region, the obtained results show a good agreement between the spatial hydro-fracturing index and the emplacement of the Cu (Cu-Fe) sulfides exploited today. The above research received funding from the European Union's Seventh Framework Program under grant agreement 228559 (ProMine project). Mejia P., Royer J.J. and A. Zielińska (2012a) - Late Cretaceous-Early Paleocene up-lift inversion in northern Europe: implications for the Kupferschiefer ore deposit in the Lubin-Sieroszowice Mining District, Poland. Promine Workshop on Mineral Resources Potential Maps, Nancy, March, France, 8p

Digital Geological Map for Marie Byrd Land, West Antarctica: A resource for investigation of geotectonic frameworks and future glaciological change

NASA Astrophysics Data System (ADS)

Siddoway, C. S.; White, T.; Elkind, S.; Cox, S. C.; Lyttle, B. S.; Morin, P. J.

2016-12-01

Bedrock exposures are relatively sparse in Marie Byrd Land (MBL), where rock is concealed by the West Antarctic ice sheet, but they provide direct insight into the geological evolution and glacial history of West Antarctica. MBL is tectonically active, as evidenced by Late Pleistocene to Holocene volcanism and 2012 seismicity (3 events, M4.4 to M5.5) at sites beside Ross Sea. There are geological influences upon the ice sheet, namely, subglacial volcanism and associated geothermal flux, fault zone alteration/mineralization, and bedrock roughess. The former may influence the position and velocity of outlet glaciers and the latter may anchor or accelerate sectors of the ice sheet. To make MBL's geological framework accessible to investigators with diverse research priorities, we are preparing the first digital geological map of MBL by compiling ground-based geological data, incorporating firsthand observations, published geological maps and literature. The map covers an on-continent coastal area of 900 000 km2 between 090°E to 160°E, from 72°S to 80°S, at 1:250 000 scale or better. Exposed rock is delimited by 1976 polygons, occupying 410 km2. Supraglacial features and glacial till, seasonal water and blue ice, are also mapped, as a baseline for past and future glaciological change. Rendered in the ArcMap GIS software by Esri©, the database employs international GeoSciML data protocols for feature classification and description of rock and moraine polygons from the Antarctic Digital Database (www.add.scar.org), with shape and location adjusted to align with features in Landsat Image Mosaic of Antarctica imagery (lima.usgs.gov), where necessary. The GIS database is attribute-rich and queriable; including links to bibliographic source files for primary literature and published maps. It will soon be available as GoogleEarth kmz files and an ArcGIS online map service. An initial application is to the interpretation of sub-ice geology for a subglacial geotectonic map of this active region. This is undertaken as part of ROSETTA-Ice, an integrated systems science investigation of the Ross Ice Shelf that commenced in 2015. The next phases of MBL database development will assess icesheet-ocean interactions near grounding line, environmental domain analysis and ecological research.

Geologic framework for the national assessment of carbon dioxide storage resources: Arkoma Basin, Kansas Basins, and Midcontinent Rift Basin study areas: Chapter F in Geologic framework for the national assessment of carbon dioxide storage resources

USGS Publications Warehouse

Buursink, Marc L.; Craddock, William H.; Blondes, Madalyn S.; Freeman, Phillip A.; Cahan, Steven M.; DeVera, Christina A.; Lohr, Celeste D.

2013-01-01

2007 Energy Independence and Security Act (Public Law 110–140) directs the U.S. Geological Survey (USGS) to conduct a national assessment of potential geologic storage resources for carbon dioxide (CO2). The methodology used by the USGS for the national CO2 assessment follows that of previous USGS work. This methodology is non-economic and intended to be used at regional to subbasinal scales. This report identifies and contains geologic descriptions of three storage assessment units (SAUs) in Upper Cambrian to Mississippian sedimentary rocks within the Arkoma Basin study area, and two SAUs in Upper Cambrian to Mississippian sedimentary rocks within the Kansas Basins study area. The Arkoma Basin and Kansas Basins are adjacent with very similar geologic units; although the Kansas Basins area is larger, the Arkoma Basin is more structurally complex. The report focuses on the characteristics, specified in the methodology, that influence the potential CO2 storage resource in the SAUs. Specific descriptions of the SAU boundaries as well as their sealing and reservoir units are included. Properties for each SAU, such as depth to top, gross thickness, porosity, permeability, groundwater quality, and structural reservoir traps, are usually provided to illustrate geologic factors critical to the assessment. Although assessment results are not contained in this report, the geologic information herein was employed, as specified in the USGS methodology, to calculate a probabilistic distribution of potential storage resources in each SAU. The Midcontinent Rift Basin study area was not assessed, because no suitable storage formations meeting our size, depth, reservoir quality, and regional seal guidelines were found. Figures in this report show study area boundaries along with the SAU boundaries and cell maps of well penetrations through sealing units into the top of the storage formations. The cell maps show the number of penetrating wells within one-square mile and are derived from interpretations of incompletely attributed well data and from a digital compilation that is known not to include all drilling. The USGS does not expect to know the location of all wells and cannot guarantee the amount of drilling through specific formations in any given cell shown on the cell maps.

Visualization and dissemination of global crustal models on virtual globes

NASA Astrophysics Data System (ADS)

Zhu, Liang-feng; Pan, Xin; Sun, Jian-zhong

2016-05-01

Global crustal models, such as CRUST 5.1 and its descendants, are very useful in a broad range of geoscience applications. The current method for representing the existing global crustal models relies heavily on dedicated computer programs to read and work with those models. Therefore, it is not suited to visualize and disseminate global crustal information to non-geological users. This shortcoming is becoming obvious as more and more people from both academic and non-academic institutions are interested in understanding the structure and composition of the crust. There is a pressing need to provide a modern, universal and user-friendly method to represent and visualize the existing global crustal models. In this paper, we present a systematic framework to easily visualize and disseminate the global crustal structure on virtual globes. Based on crustal information exported from the existing global crustal models, we first create a variety of KML-formatted crustal models with different levels of detail (LODs). And then the KML-formatted models can be loaded into a virtual globe for 3D visualization and model dissemination. A Keyhole Markup Language (KML) generator (Crust2KML) is developed to automatically convert crustal information obtained from the CRUST 1.0 model into KML-formatted global crustal models, and a web application (VisualCrust) is designed to disseminate and visualize those models over the Internet. The presented framework and associated implementations can be conveniently exported to other applications to support visualizing and analyzing the Earth's internal structure on both regional and global scales in a 3D virtual-globe environment.

Surface Mass Balance of the Greenland Ice Sheet Derived from Paleoclimate Reanalysis

NASA Astrophysics Data System (ADS)

Badgeley, J.; Steig, E. J.; Hakim, G. J.; Anderson, J.; Tardif, R.

2017-12-01

Modeling past ice-sheet behavior requires independent knowledge of past surface mass balance. Though models provide useful insight into ice-sheet response to climate forcing, if past climate is unknown, then ascertaining the rate and extent of past ice-sheet change is limited to geological and geophysical constraints. We use a novel data-assimilation framework developed under the Last Millennium Reanalysis Project (Hakim et al., 2016) to reconstruct past climate over ice sheets with the intent of creating an independent surface mass balance record for paleo ice-sheet modeling. Paleoclimate data assimilation combines the physics of climate models and the time series evidence of proxy records in an offline, ensemble-based approach. This framework allows for the assimilation of numerous proxy records and archive types while maintaining spatial consistency with known climate dynamics and physics captured by the models. In our reconstruction, we use the Community Climate System Model version 4, CMIP5 last millennium simulation (Taylor et al., 2012; Landrum et al., 2013) and a nearly complete database of ice core oxygen isotope records to reconstruct Holocene surface temperature and precipitation over the Greenland Ice Sheet on a decadal timescale. By applying a seasonality to this reconstruction (from the TraCE-21ka simulation; Liu et al., 2009), our reanalysis can be used in seasonally-based surface mass balance models. Here we discuss the methods behind our reanalysis and the performance of our reconstruction through prediction of unassimilated proxy records and comparison to paleoclimate reconstructions and reanalysis products.

Geologic Assessment of Undiscovered Gas Resources of the Eastern Oregon and Washington Province

USGS Publications Warehouse

U.S. Geological Survey Eastern Oregon and Washington Province Assessment Team, (compiler)

2008-01-01

The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geology-based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States, focusing on the distribution, quantity, and availability of oil and natural gas resources. The USGS has completed an assessment of the undiscovered oil and gas potential of the Eastern Oregon and Washington Province of Oregon and Washington (USGS Province 5005). The province is a priority Energy Policy and Conservation Act (EPCA) province for the National Assessment because of its potential for oil and gas resources. The assessment of this province is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (stratigraphy, sedimentology, petrophysical properties), and hydrocarbon traps (trap formation and timing). In the Eastern Oregon and Washington Province, the USGS used this geologic framework to define one total petroleum system and two assessment units within the total petroleum system, and quantitatively estimated the undiscovered gas resources within each assessment unit.

Petroleum systems and geologic assessment of undiscovered oil and gas, Cotton Valley group and Travis Peak-Hosston formations, East Texas basin and Louisiana-Mississippi salt basins provinces of the northern Gulf Coast region. Chapters 1-7.

USGS Publications Warehouse

,

2006-01-01

The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas potential of the Cotton Valley Group and Travis Peak and Hosston Formations in the East Texas Basin and Louisiana-Mississippi Salt Basins Provinces in the Gulf Coast Region (USGS Provinces 5048 and 5049). The Cotton Valley Group and Travis Peak and Hosston Formations are important because of their potential for natural gas resources. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define one total petroleum system and eight assessment units. Seven assessment units were quantitatively assessed for undiscovered oil and gas resources.

3D subsurface geological modeling using GIS, remote sensing, and boreholes data

NASA Astrophysics Data System (ADS)

Kavoura, Katerina; Konstantopoulou, Maria; Kyriou, Aggeliki; Nikolakopoulos, Konstantinos G.; Sabatakakis, Nikolaos; Depountis, Nikolaos

2016-08-01

The current paper presents the combined use of geological-geotechnical insitu data, remote sensing data and GIS techniques for the evaluation of a subsurface geological model. High accuracy Digital Surface Model (DSM), airphotos mosaic and satellite data, with a spatial resolution of 0.5m were used for an othophoto base map compilation of the study area. Geological - geotechnical data obtained from exploratory boreholes and the 1:5000 engineering geological maps were digitized and implemented in a GIS platform for a three - dimensional subsurface model evaluation. The study is located at the North part of Peloponnese along the new national road.

Integration of 3D geological modeling and gravity surveys for geothermal prospection in an Alpine region

NASA Astrophysics Data System (ADS)

Guglielmetti, L.; Comina, C.; Abdelfettah, Y.; Schill, E.; Mandrone, G.

2013-11-01

Thermal sources are common manifestations of geothermal energy resources in Alpine regions. The up-flow of the fluid is well-known to be often linked to cross-cutting fault zones providing a significant volume of fractures. Since conventional exploration methods are challenging in such areas of high topography and complicated logistics, 3D geological modeling based on structural investigation becomes a useful tool for assessing the overall geology of the investigated sites. Geological modeling alone is, however, less effective if not integrated with deep subsurface investigations that could provide a first order information on geological boundaries and an imaging of geological structures. With this aim, in the present paper the combined use of 3D geological modeling and gravity surveys for geothermal prospection of a hydrothermal area in the western Alps was carried out on two sites located in the Argentera Massif (NW Italy). The geothermal activity of the area is revealed by thermal anomalies with surface evidences, such as hot springs, at temperatures up to 70 °C. Integration of gravity measurements and 3D modeling investigates the potential of this approach in the context of geothermal exploration in Alpine regions where a very complex geological and structural setting is expected. The approach used in the present work is based on the comparison between the observed gravity and the gravity effect of the 3D geological models, in order to enhance local effects related to the geothermal system. It is shown that a correct integration of 3D modeling and detailed geophysical survey could allow a better characterization of geological structures involved in geothermal fluids circulation. Particularly, gravity inversions have successfully delineated the continuity in depth of low density structures, such as faults and fractured bands observed at the surface, and have been of great help in improving the overall geological model.

Forward modeling of gravity data using geostatistically generated subsurface density variations

USGS Publications Warehouse

Phelps, Geoffrey

2016-01-01

Using geostatistical models of density variations in the subsurface, constrained by geologic data, forward models of gravity anomalies can be generated by discretizing the subsurface and calculating the cumulative effect of each cell (pixel). The results of such stochastically generated forward gravity anomalies can be compared with the observed gravity anomalies to find density models that match the observed data. These models have an advantage over forward gravity anomalies generated using polygonal bodies of homogeneous density because generating numerous realizations explores a larger region of the solution space. The stochastic modeling can be thought of as dividing the forward model into two components: that due to the shape of each geologic unit and that due to the heterogeneous distribution of density within each geologic unit. The modeling demonstrates that the internally heterogeneous distribution of density within each geologic unit can contribute significantly to the resulting calculated forward gravity anomaly. Furthermore, the stochastic models match observed statistical properties of geologic units, the solution space is more broadly explored by producing a suite of successful models, and the likelihood of a particular conceptual geologic model can be compared. The Vaca Fault near Travis Air Force Base, California, can be successfully modeled as a normal or strike-slip fault, with the normal fault model being slightly more probable. It can also be modeled as a reverse fault, although this structural geologic configuration is highly unlikely given the realizations we explored.

Analysis of geologic terrain models for determination of optimum SAR sensor configuration and optimum information extraction for exploration of global non-renewable resources. Pilot study: Arkansas Remote Sensing Laboratory, part 1, part 2, and part 3

NASA Technical Reports Server (NTRS)

Kaupp, V. H.; Macdonald, H. C.; Waite, W. P.; Stiles, J. A.; Frost, F. S.; Shanmugam, K. S.; Smith, S. A.; Narayanan, V.; Holtzman, J. C. (Principal Investigator)

1982-01-01

Computer-generated radar simulations and mathematical geologic terrain models were used to establish the optimum radar sensor operating parameters for geologic research. An initial set of mathematical geologic terrain models was created for three basic landforms and families of simulated radar images were prepared from these models for numerous interacting sensor, platform, and terrain variables. The tradeoffs between the various sensor parameters and the quantity and quality of the extractable geologic data were investigated as well as the development of automated techniques of digital SAR image analysis. Initial work on a texture analysis of SEASAT SAR imagery is reported. Computer-generated radar simulations are shown for combinations of two geologic models and three SAR angles of incidence.

The potential of audiomagnetotellurics in the study of geothermal fields: A case study from the northern segment of the La Candelaria Range, northwestern Argentina

NASA Astrophysics Data System (ADS)

Barcelona, Hernan; Favetto, Alicia; Peri, Veronica Gisel; Pomposiello, Cristina; Ungarelli, Carlo

2013-01-01

Despite its reduced penetration depth, audiomagnetotelluric (AMT) studies can be used to determine a broad range of features related to little studied geothermal fields. This technique requires a stepwise interpretation of results taking into consideration diverse information (e.g. topographic, hydrological, geological and/or structural data) to constrain the characteristics of the study area. In this work, an AMT study was performed at the hot springs in the northern segment of the La Candelaria Range in order to characterize the area at depth. Geometric aspects of the shallow subsurface were determined based on the dimensional and distortion analysis of the impedance tensors. Also, the correlation between structural features and regional strikes allowed us to define two geoelectric domains, useful to determine the controls on fluid circulation. The subsurface resistivity distribution was determined through 1D and 2D models. The patterns of the 1D models were compared with the morpho-structure of the range. Shallow and deep conductive zones were defined and a possible shallow geothermal system scheme proposed. A strong correlation was found between the AMT results and the geological framework of the region, showing the relevance of using AMT in geothermal areas during the early stages of subsurface prospecting.

Model of the development of the Rif/Prerif basin and implications for the hydrocarbon prospectivity of northern Morocco

DOE Office of Scientific and Technical Information (OSTI.GOV)

Munro, S.E.

1988-08-01

The geology of northern Morocco is dominated by the mountainous areas of the Rif and the Prerif. These mountains form the southern half of the Rif-Betic arc. The surface geology of the Prerif area is characterized by the allochthonous mass of the Prerif nappe, which is variously described as a tectonic melange, an olistostrome, or a combination of the two. It is structurally extremely complex and this fact has, in the past, deterred international companies from exploring for oil in the area. Recently acquired seismic data shed some light on the structure within the Prerif nappe; it tends to supportmore » a tectonic origin rather than one based on gravity drive. In this framework, a model is proposed for the tectonic development of the Rif/Prerif in particular and the Rif/Betic arc in general, based upon the interaction of the Iberian, Moroccan, and Alboran plates from the Triassic to the Neogene. The seismic data also show, however, that a sizeable Mesozoic trough exists beneath the mass of the Prerif nappe. In addition, several piggyback basins are developed above the nappe. Therefore, considerable potential for oil and gas discoveries exists both above and below the nappe.« less

Structural controls on anomalous transport in fractured porous rock

NASA Astrophysics Data System (ADS)

Edery, Yaniv; Geiger, Sebastian; Berkowitz, Brian

2016-07-01

Anomalous transport is ubiquitous in a wide range of disordered systems, notably in fractured porous formations. We quantitatively identify the structural controls on anomalous tracer transport in a model of a real fractured geological formation that was mapped in an outcrop. The transport, determined by a continuum scale mathematical model, is characterized by breakthrough curves (BTCs) that document anomalous (or "non-Fickian") transport, which is accounted for by a power law distribution of local transition times ψ>(t>) within the framework of a continuous time random walk (CTRW). We show that the determination of ψ>(t>) is related to fractures aligned approximately with the macroscopic direction of flow. We establish the dominant role of fracture alignment and assess the statistics of these fractures by determining a concentration-visitation weighted residence time histogram. We then convert the histogram to a probability density function (pdf) that coincides with the CTRW ψ>(t>) and hence anomalous transport. We show that the permeability of the geological formation hosting the fracture network has a limited effect on the anomalous nature of the transport; rather, it is the fractures transverse to the flow direction that play the major role in forming the long BTC tail associated with anomalous transport. This is a remarkable result, given the complexity of the flow field statistics as captured by concentration transitions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noel, Donna

This project integrated state-of-the-art exploration technologies with a geologic framework and reservoir modeling to ultimately determine the efficacy of future geothermal production within the PLPT reservation. The information gained during this study should help the PLPT to make informed decisions regarding construction of a geothermal power plant. Additional benefits included the transfer of new technologies and geothermal data to the geothermal industry and it created and/or preserved nearly three dozen jobs accordance with the American Recovery and Reinvestment Act of 2009. A variety of tasks were conducted to achieve the above stated objectives. The following are the tasks completed withinmore » the project: 1. Permitting 2. Shallow temperature survey 3. Seismic data collection and analysis 4. Fracture stress analysis 5. Phase I reporting Permitting 7. Shallow temperature survey 8. Seismic data collection and analysis 9. Fracture stress analysis 10. Phase I reporting 11. Drilling two new wells 12. Borehole geophysics 13. Phase II reporting 14. Well testing and geochemical analysis 15. Three-dimensional geologic model 16. Three-dimensional reservoir analysis 17. Reservation wide geothermal potential analysis 18. Phase III reporting Phase I consisted of tasks 1 – 5, Phase II tasks 6 – 8, and Phase III tasks 9 – 13. This report details the results of Phase III tasks. Reports are available for Phase I, and II as separate documents.« less

Uncertainty estimation of simulated water levels for the Mitch flood event in Tegucigalpa

NASA Astrophysics Data System (ADS)

Fuentes Andino, Diana Carolina; Halldin, Sven; Keith, Beven; Chong-Yu, Xu

2013-04-01

Hurricane Mitch in 1998 left a devastating flood in Tegucigalpa, the capital city of Honduras. Due to the extremely large magnitude of the Mitch flood, hydrometric measurements were not taken during the event. However, post-event indirect measurements of the discharge were obtained by the U.S. Geological Survey (USGS) and post-event surveyed high water marks were obtained by the Japan International Cooperation agency (JICA). This work proposes a methodology to simulate the water level during the Mitch event when the available data is associated with large uncertainty. The results of the two-dimensional hydrodynamic model LISFLOOD-FP will be evaluated using the Generalized Uncertainty Estimation (GLUE) framework. The main challenge in the proposed methodology is to formulate an approach to evaluate the model results when there are large uncertainties coming from both the model parameters and the evaluation data.

An approach to regional wetland digital elevation model development using a differential global positioning system and a custom-built helicopter-based surveying system

USGS Publications Warehouse

Jones, J.W.; Desmond, G.B.; Henkle, C.; Glover, R.

2012-01-01

Accurate topographic data are critical to restoration science and planning for the Everglades region of South Florida, USA. They are needed to monitor and simulate water level, water depth and hydroperiod and are used in scientific research on hydrologic and biologic processes. Because large wetland environments and data acquisition challenge conventional ground-based and remotely sensed data collection methods, the United States Geological Survey (USGS) adapted a classical data collection instrument to global positioning system (GPS) and geographic information system (GIS) technologies. Data acquired with this instrument were processed using geostatistics to yield sub-water level elevation values with centimetre accuracy (??15 cm). The developed database framework, modelling philosophy and metadata protocol allow for continued, collaborative model revision and expansion, given additional elevation or other ancillary data. ?? 2012 Taylor & Francis.

New Geologic Map and Structural Cross Sections of the Death Valley Extended Terrain (southern Sierra Nevada, California to Spring Mountains, Nevada): Toward 3D Kinematic Reconstructions

NASA Astrophysics Data System (ADS)

Lutz, B. M.; Axen, G. J.; Phillips, F. M.

2017-12-01

Tectonic reconstructions for the Death Valley extended terrain (S. Sierra Nevada to Spring Mountains) have evolved to include a growing number of offset markers for strike-slip fault systems but are mainly map view (2D) and do not incorporate a wealth of additional constraints. We present a new 1:300,000 digital geologic map and structural cross sections, which provide a geometric framework for stepwise 3D reconstructions of Late Cenozoic extension and transtension. 3D models will decipher complex relationships between strike-slip, normal, and detachment faults and their role in accommodating large magnitude extension/rigid block rotation. Fault coordination is key to understanding how extensional systems and transform margins evolve with changing boundary conditions. 3D geometric and kinematic analysis adds key strain compatibility unavailable in 2D reconstructions. The stratigraphic framework of Fridrich and Thompson (2011) is applied to rocks outside of Death Valley. Cenozoic basin deposits are grouped into 6 assemblages differentiated by age, provenance, and bounding unconformities, which reflect Pacific-North American plate boundary events. Pre-Cenozoic rocks are grouped for utility: for example, Cararra Formation equivalents are grouped because they form a Cordilleran thrust decollement zone. Offset markers are summarized in the associated tectonic map. Other constraints include fault geometries and slip rates, age, geometry and provenance of Cenozoic basins, gravity, cooling histories of footwalls, and limited seismic/well data. Cross sections were constructed parallel to net-transport directions of fault blocks. Surface fault geometries were compiled from previous mapping and projected to depth using seismic/gravity data. Cooling histories of footwalls guided geometric interpretation of uplifted detachment footwalls. Mesh surfaces will be generated from 2D section lines to create a framework for stepwise 3D reconstruction of extension and transtension in the study area. Analysis of all available data in a seamless 3D framework should force more unique solutions to outstanding kinematic problems, provide a better understanding of the Cordilleran thrust belt, and constrain the mechanisms of strain partitioning between the upper and lower crust.

Co-Optimization of CO 2-EOR and Storage Processes in Mature Oil Reservoirs

DOE PAGES

Ampomah, William; Balch, Robert S.; Grigg, Reid B.; ...

2016-08-02

This article presents an optimization methodology for CO 2 enhanced oil recovery in partially depleted reservoirs. A field-scale compositional reservoir flow model was developed for assessing the performance history of an active CO 2 flood and for optimizing both oil production and CO 2 storage in the Farnsworth Unit (FWU), Ochiltree County, Texas. A geological framework model constructed from geophysical, geological, and engineering data acquired from the FWU was the basis for all reservoir simulations and the optimization method. An equation of state was calibrated with laboratory fluid analyses and subsequently used to predict the thermodynamic minimum miscible pressure (MMP).more » Initial history calibrations of primary, secondary and tertiary recovery were conducted as the basis for the study. After a good match was achieved, an optimization approach consisting of a proxy or surrogate model was constructed with a polynomial response surface method (PRSM). The PRSM utilized an objective function that maximized both oil recovery and CO 2 storage. Experimental design was used to link uncertain parameters to the objective function. Control variables considered in this study included: water alternating gas cycle and ratio, production rates and bottom-hole pressure of injectors and producers. Other key parameters considered in the modeling process were CO 2 purchase, gas recycle and addition of infill wells and/or patterns. The PRSM proxy model was ‘trained’ or calibrated with a series of training simulations. This involved an iterative process until the surrogate model reached a specific validation criterion. A sensitivity analysis was first conducted to ascertain which of these control variables to retain in the surrogate model. A genetic algorithm with a mixed-integer capability optimization approach was employed to determine the optimum developmental strategy to maximize both oil recovery and CO 2 storage. The proxy model reduced the computational cost significantly. The validation criteria of the reduced order model ensured accuracy in the dynamic modeling results. The prediction outcome suggested robustness and reliability of the genetic algorithm for optimizing both oil recovery and CO 2 storage. The reservoir modeling approach used in this study illustrates an improved approach to optimizing oil production and CO 2 storage within partially depleted oil reservoirs such as FWU. Lastly, this study may serve as a benchmark for potential CO 2–EOR projects in the Anadarko basin and/or geologically similar basins throughout the world.« less

Co-Optimization of CO 2-EOR and Storage Processes in Mature Oil Reservoirs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ampomah, William; Balch, Robert S.; Grigg, Reid B.

This article presents an optimization methodology for CO 2 enhanced oil recovery in partially depleted reservoirs. A field-scale compositional reservoir flow model was developed for assessing the performance history of an active CO 2 flood and for optimizing both oil production and CO 2 storage in the Farnsworth Unit (FWU), Ochiltree County, Texas. A geological framework model constructed from geophysical, geological, and engineering data acquired from the FWU was the basis for all reservoir simulations and the optimization method. An equation of state was calibrated with laboratory fluid analyses and subsequently used to predict the thermodynamic minimum miscible pressure (MMP).more » Initial history calibrations of primary, secondary and tertiary recovery were conducted as the basis for the study. After a good match was achieved, an optimization approach consisting of a proxy or surrogate model was constructed with a polynomial response surface method (PRSM). The PRSM utilized an objective function that maximized both oil recovery and CO 2 storage. Experimental design was used to link uncertain parameters to the objective function. Control variables considered in this study included: water alternating gas cycle and ratio, production rates and bottom-hole pressure of injectors and producers. Other key parameters considered in the modeling process were CO 2 purchase, gas recycle and addition of infill wells and/or patterns. The PRSM proxy model was ‘trained’ or calibrated with a series of training simulations. This involved an iterative process until the surrogate model reached a specific validation criterion. A sensitivity analysis was first conducted to ascertain which of these control variables to retain in the surrogate model. A genetic algorithm with a mixed-integer capability optimization approach was employed to determine the optimum developmental strategy to maximize both oil recovery and CO 2 storage. The proxy model reduced the computational cost significantly. The validation criteria of the reduced order model ensured accuracy in the dynamic modeling results. The prediction outcome suggested robustness and reliability of the genetic algorithm for optimizing both oil recovery and CO 2 storage. The reservoir modeling approach used in this study illustrates an improved approach to optimizing oil production and CO 2 storage within partially depleted oil reservoirs such as FWU. Lastly, this study may serve as a benchmark for potential CO 2–EOR projects in the Anadarko basin and/or geologically similar basins throughout the world.« less

Plate motions and deformations from geologic and geodetic data

NASA Technical Reports Server (NTRS)

Jordan, Thomas H.

1989-01-01

The very long baseline interferometry (VLBI) measurements made in the western U.S. since 1979 provide discrete samples of the temporal and spatial deformation field. The interpretation of the VLBI derived rates of deformation requires an examination of geologic information and more densely sampled ground based geodetic data. Triangulation and trilateration data measured on two regional networks, one in the central Mojave Desert and one in the Coast Ranges east of the San Andreas fault, were processed. At the spatial scales spanned by these local geodetic networks, auxiliary geologic and geophysical data were utilized to examine the relation between measured incremental strain and the accommodation of strain seen in local geologic structures, strain release in earthquakes, and principal stress directions inferred from in situ measurements. VLBI data was also processed from stations distributed across the Pacific-North America plate boundary zone in the western U.S. The VLBI data were used to constrain the integrated rate of deformation across portions of the continental plate boundary in California and to provide a tectonic framework to interpret regional geodetic and geologic studies.

Earth's earliest biosphere-a proposal to develop a collection of curated archean geologic reference materials

NASA Technical Reports Server (NTRS)

Lindsay, John F.; McKay, David S.; Allen, Carlton C.

2003-01-01

The discovery of evidence indicative of life in a Martian meteorite has led to an increase in interest in astrobiology. As a result of this discovery, and the ensuing controversy, it has become apparent that our knowledge of the early development of life on Earth is limited. Archean stratigraphic successions containing evidence of Earth's early biosphere are well preserved in the Pilbara Craton of Western Australia. The craton includes part of a protocontinent consisting of granitoid complexes that were emplaced into, and overlain by, a 3.51-2.94 Ga volcanigenic carapace - the Pilbara Supergroup. The craton is overlain by younger supracrustal basins that form a time series recording Earth history from approximately 2.8 Ga to approximately 1.9 Ga. It is proposed that a well-documented suite of these ancient rocks be collected as reference material for Archean and astrobiological research. All samples would be collected in a well-defined geological context in order to build a framework to test models for the early evolution of life on Earth and to develop protocols for the search for life on other planets.

Waste isolation and contaminant migration - Tools and techniques for monitoring the saturated zone-unsaturated zone-plant-atmosphere continuum

USGS Publications Warehouse

Andraski, Brian J.; Stonestrom, David A.; Nicholson, T.J.; Arlt, H.D.

2011-01-01

In 1976 the U.S. Geological Survey (USGS) began studies of unsaturated zone hydrology next to the Nation’s first commercial disposal facility for low-level radioactive waste (LLRW) near Beatty, NV. Recognizing the need for long-term data collection, the USGS in 1983 established research management areas in the vicinity of the waste-burial facility through agreements with the Bureau of Land Management and the State of Nevada. Within this framework, the Amargosa Desert Research Site (ADRS; http://nevada.usgs.gov/adrs/) is serving as a field laboratory for the sustained study of water-, gas-, and contaminant-transport processes, and the development of models and methods to characterize flow and transport. The research is built on multiple lines of data that include: micrometeorology; evapotranspiration; plant metrics; soil and sediment properties; unsaturated-zone moisture, temperature, and gas composition; geology and geophysics; and groundwater. Contaminant data include tritium, radiocarbon, volatile-organic compounds (VOCs), and elemental mercury. Presented here is a summary of monitoring tools and techniques that are being applied in studies of waste isolation and contaminant migration.

Formation of modern and Paleozoic stratiform barite at cold methane seeps on continental margins

USGS Publications Warehouse

Torres, M.E.; Bohrmann, G.; Dube, T.E.; Poole, F.G.

2003-01-01

Stratiform (bedded) Paleozoic barite occurs as large conformable beds within organic- and chert-rich sediments; the beds lack major sulfide minerals and are the largest and most economically significant barite deposits in the geologic record. Existing models for the origin of bedded barite fail to explain all their characteristics: the deposits display properties consistent with an exhalative origin involving fluid ascent to the seafloor, but they lack appreciable polymetallic sulfide minerals and the corresponding strontium isotopic composition to support a hydrothermal vent source. A new mechanism of barite formation, along structurally controlled sites of cold fluid seepage in continental margins, involves barite remobilization in organic-rich, highly reducing sediments, transport of barium-rich fluids, and barite precipitation at cold methane seeps. The lithologic and depositional framework of Paleozoic and cold seep barite, as well as morphological, textural, and chemical characteristics of the deposits, and associations with chemosymbiotic fauna, all support a cold seep origin for stratiform Paleozoic barite. This understanding is highly relevant to paleoceanographic and paleotectonic studies, as well as to economic geology.

Uncertainty quantification of crustal scale thermo-chemical properties in Southeast Australia

NASA Astrophysics Data System (ADS)

Mather, B.; Moresi, L. N.; Rayner, P. J.

2017-12-01

The thermo-chemical properties of the crust are essential to understanding the mechanical and thermal state of the lithosphere. The uncertainties associated with these parameters are connected to the available geophysical observations and a priori information to constrain the objective function. Often, it is computationally efficient to reduce the parameter space by mapping large portions of the crust into lithologies that have assumed homogeneity. However, the boundaries of these lithologies are, in themselves, uncertain and should also be included in the inverse problem. We assimilate geological uncertainties from an a priori geological model of Southeast Australia with geophysical uncertainties from S-wave tomography and 174 heat flow observations within an adjoint inversion framework. This reduces the computational cost of inverting high dimensional probability spaces, compared to probabilistic inversion techniques that operate in the `forward' mode, but at the sacrifice of uncertainty and covariance information. We overcome this restriction using a sensitivity analysis, that perturbs our observations and a priori information within their probability distributions, to estimate the posterior uncertainty of thermo-chemical parameters in the crust.

The economic value of remote sensing information: a case study of agricultural production and groundwater vulnerability using applied environmental science and hydrogeospatial methods

NASA Astrophysics Data System (ADS)

Forney, W.; Bernknopf, R. L.; Mishra, S.; Raunikar, R. P.

2011-12-01

William M. Forney1*, Richard L. Bernknopf1, Shruti K. Mishra2, Ronald P. Raunikar1. 1=Western Geographic Science Center, US Geological Survey, Menlo Park, California. 2=Contractor, Western Geographic Science Center, US Geological Survey, Menlo Park, California *=Contact author, wforney@usgs.gov, 650-329-4237. Does remote sensing information provide economic benefits to society and can those benefits be valued? Can resource management and policy be better informed by coupling past and present earth observations with groundwater nitrate measurements? Using an integrated assessment approach, the USGS's research applies an established conceptual framework to answer these questions as well as estimate the value of information (VOI) for remote sensing imagery. The approach uses moderate resolution land imagery (MRLI) data from the Landsat and Advanced Wide Field Sensor satellites that has been classified by the National Agricultural Statistics Service into the Cropland Data Layer (CDL). Within the constraint of the US Environmental Protection Agency's public health threshold for potable groundwater resources, we model the relationship between a population of the CDL's land uses and the evolution of nitrate (NO3-) contamination of aquifers in a case study region in northeastern Iowa. Using source data from the Iowa Department of Natural Resources and the USGS's National Water Quality Assessment Program, the approach uses multi-scaled, environmental science models to address dynamic, biophysical process models of nitrogen fate and transport at specific sites (wells) and at landscape scale (35 counties) in order to assess groundwater vulnerability. In addition to the ecosystem service of potable groundwater, this effort focuses on particular agricultural goods and land uses: corn, soybeans and livestock manure management. Results of this four-year study will be presented, including: 1) the integrated models of the assessment approach, 2) mapping the range of vulnerabilities across the region, and 3) considerations of improved nitrogen and crop management. Finally, utilizing both a situation where society does not have access to MRLI, and an enhanced land use scenario based on plausible, future regulatory and policy frameworks and continued availability of MRLI, estimates of the incremental increase in the MRLI's VOI are presented.

A Leadership Model for University Geology Department Teacher Inservice Programs.

ERIC Educational Resources Information Center

Sheldon, Daniel S.; And Others

1983-01-01

Provides geology departments and science educators with a leadership model for developing earth science inservice programs. Model emphasizes cooperation/coordination among departments, science educators, and curriculum specialists at local/intermediate/state levels. Includes rationale for inservice programs and geology department involvement in…

Inner-shelf ocean dynamics and seafloor morphologic changes during Hurricane Sandy

NASA Astrophysics Data System (ADS)

Warner, John C.; Schwab, William C.; List, Jeffrey H.; Safak, Ilgar; Liste, Maria; Baldwin, Wayne

2017-04-01

Hurricane Sandy was one of the most destructive hurricanes in US history, making landfall on the New Jersey coast on October 30, 2012. Storm impacts included several barrier island breaches, massive coastal erosion, and flooding. While changes to the subaerial landscape are relatively easily observed, storm-induced changes to the adjacent shoreface and inner continental shelf are more difficult to evaluate. These regions provide a framework for the coastal zone, are important for navigation, aggregate resources, marine ecosystems, and coastal evolution. Here we provide unprecedented perspective regarding regional inner continental shelf sediment dynamics based on both observations and numerical modeling over time scales associated with these types of large storm events. Oceanographic conditions and seafloor morphologic changes are evaluated using both a coupled atmospheric-ocean-wave-sediment numerical modeling system that covered spatial scales ranging from the entire US east coast (1000 s of km) to local domains (10 s of km). Additionally, the modeled response for the region offshore of Fire Island, NY was compared to observational analysis from a series of geologic surveys from that location. The geologic investigations conducted in 2011 and 2014 revealed lateral movement of sedimentary structures of distances up to 450 m and in water depths up to 30 m, and vertical changes in sediment thickness greater than 1 m in some locations. The modeling investigations utilize a system with grid refinement designed to simulate oceanographic conditions with progressively increasing resolutions for the entire US East Coast (5-km grid), the New York Bight (700-m grid), and offshore of Fire Island, NY (100-m grid), allowing larger scale dynamics to drive smaller scale coastal changes. Model results in the New York Bight identify maximum storm surge of up to 3 m, surface currents on the order of 2 ms-1 along the New Jersey coast, waves up to 8 m in height, and bottom stresses exceeding 10 Pa. Flow down the Hudson Shelf Valley is shown to result in convergent sediment transport and deposition along its axis. Modeled sediment redistribution along Fire Island showed erosion across the crests of inner shelf sand ridges and sedimentation in adjacent troughs, consistent with the geologic observations.

Three-Dimensional Online Visualization and Engagement Tools for the Geosciences

NASA Astrophysics Data System (ADS)

Cockett, R.; Moran, T.; Pidlisecky, A.

2013-12-01

Educational tools often sacrifice interactivity in favour of scalability so they can reach more users. This compromise leads to tools that may be viewed as second tier when compared to more engaging activities performed in a laboratory; however, the resources required to deliver laboratory exercises that are scalable is often impractical. Geoscience education is well situated to benefit from interactive online learning tools that allow users to work in a 3D environment. Visible Geology (http://3ptscience.com/visiblegeology) is an innovative web-based application designed to enable visualization of geologic structures and processes through the use of interactive 3D models. The platform allows users to conceptualize difficult, yet important geologic principles in a scientifically accurate manner by developing unique geologic models. The environment allows students to interactively practice their visualization and interpretation skills by creating and interacting with their own models and terrains. Visible Geology has been designed from a user centric perspective resulting in a simple and intuitive interface. The platform directs students to build there own geologic models by adding beds and creating geologic events such as tilting, folding, or faulting. The level of ownership and interactivity encourages engagement, leading learners to discover geologic relationships on their own, in the context of guided assignments. In January 2013, an interactive geologic history assignment was developed for a 700-student introductory geology class at The University of British Columbia. The assignment required students to distinguish the relative age of geologic events to construct a geologic history. Traditionally this type of exercise has been taught through the use of simple geologic cross-sections showing crosscutting relationships; from these cross-sections students infer the relative age of geologic events. In contrast, the Visible Geology assignment offers students a unique experience where they first create their own geologic events allowing them to directly see how the timing of a geologic event manifests in the model and resulting cross-sections. By creating each geologic event in the model themselves, the students gain a deeper understanding of the processes and relative order of events. The resulting models can be shared amongst students, and provide instructors with a basis for guiding inquiry to address misconceptions. The ease of use of the assignment, including automatic assessment, made this tool practical for deployment in this 700 person class. The outcome of this type of large scale deployment is that students, who would normally not experience a lab exercise, gain exposure to interactive 3D thinking. Engaging tools and software that puts the user in control of their learning experiences is critical for moving to scalable, yet engaging, online learning environments.

Using digital databases to create geologic maps for the 21st century : a GIS model for geologic, environmental, cultural and transportation data from southern Rhode Island

DOT National Transportation Integrated Search

2002-05-01

Knowledge of surface and subsurface geology is fundamental to the planning and development of new or modified transportation systems. Toward this : end, we have compiled a model GIS database consisting of important geologic, cartographic, environment...

Geologic context of large karst springs and caves in the Ozark National Scenic Riverways, Missouri

USGS Publications Warehouse

Weary, David J.; Orndorff, Randall C.

2016-01-01

The ONSR is a karst park, containing many springs and caves. The “jewels” of the park are large springs, several of first magnitude, that contribute significantly to the flow and water quality of the Current River and its tributaries. Completion of 1:24,000-scale geologic mapping of the park and surrounding river basin, along with synthesis of published hydrologic data, allows us to examine the spatial relationships between the springs and the geologic framework to develop a conceptual model for genesis of these springs. Based on their similarity to mapped spring conduits, many of the caves in the ONSR are fossil conduit segments. Therefore, geologic control on the evolution of the springs also applies to speleogenesis in this part of the southern Missouri Ozarks.Large springs occur in the ONSR area because: (1) the Ozark aquifer, from which they rise, is chiefly dolomite affected by solution via various processes over a long time period, (2) Paleozoic hypogenic fluid migration through these rocks exploited and enhanced flow-paths, (3) a consistent and low regional dip of the rocks off of the Salem Plateau (less than 2° to the southeast) allows integration of flow into large groundwater basins with a few discreet outlets, (4) the springs are located where the rivers have cut down into structural highs, allowing access to water from stratigraphic units deeper in the aquifer thus allowing development of springsheds that have volumetrically larger storage than smaller springs higher in the section, and (5) quartz sandstone and bedded chert in the carbonate stratigraphic succession that are locally to regionally continuous, serve as aquitards that locally confine groundwater up dip of the springs creating artesian conditions. This subhorizontal partitioning of the Ozark aquifer allows contributing areas for different springs to overlap, as evidenced by dye traces that cross adjacent groundwater basin boundaries, and possibly contributes to alternate flow routes under different groundwater flow regimes.A better understanding of the 3-dimensional hydrogeologic framework for the large spring systems in the ONSR allows more precise mapping of the contributing areas for those springs, will guide future studies of groundwater flow paths, and inform development of groundwater resource management strategies for the park.

The topology of geology 1: Topological analysis

NASA Astrophysics Data System (ADS)

Thiele, Samuel T.; Jessell, Mark W.; Lindsay, Mark; Ogarko, Vitaliy; Wellmann, J. Florian; Pakyuz-Charrier, Evren

2016-10-01

Topology has been used to characterise and quantify the properties of complex systems in a diverse range of scientific domains. This study explores the concept and applications of topological analysis in geology. We have developed an automatic system for extracting first order 2D topological information from geological maps, and 3D topological information from models built with the Noddy kinematic modelling system, and equivalent analyses should be possible for other implicit modelling systems. A method is presented for describing the spatial and temporal topology of geological models using a set of adjacency relationships that can be expressed as a topology network, thematic adjacency matrix or hive diagram. We define three types of spatial topology (cellular, structural and lithological) that allow us to analyse different aspects of the geology, and then apply them to investigate the geology of the Hamersley Basin, Western Australia.

Micro-Macro Analysis and Phenomenological Modelling of Salt Viscous Damage and Application to Salt Caverns

NASA Astrophysics Data System (ADS)

Zhu, Cheng; Pouya, Ahmad; Arson, Chloé

2015-11-01

This paper aims to gain fundamental understanding of the microscopic mechanisms that control the transition between secondary and tertiary creep around salt caverns in typical geological storage conditions. We use a self-consistent inclusion-matrix model to homogenize the viscoplastic deformation of halite polycrystals and predict the number of broken grains in a Representative Elementary Volume of salt. We use this micro-macro modeling framework to simulate creep tests under various axial stresses, which gives us the critical viscoplastic strain at which grain breakage (i.e., tertiary creep) is expected to occur. The comparison of simulation results for short-term and long-term creep indicates that the initiation of tertiary creep depends on the stress and the viscoplastic strain. We use the critical viscoplastic deformation as a yield criterion to control the transition between secondary and tertiary creep in a phenomenological viscoplastic model, which we implement into the Finite Element Method program POROFIS. We model a 850-m-deep salt cavern of irregular shape, in axis-symmetric conditions. Simulations of cavern depressurization indicate that a strain-dependent damage evolution law is more suitable than a stress-dependent damage evolution law, because it avoids high damage concentrations and allows capturing the formation of a damaged zone around the cavity. The modeling framework explained in this paper is expected to provide new insights to link grain breakage to phenomenological damage variables used in Continuum Damage Mechanics.

A general gridding, discretization, and coarsening methodology for modeling flow in porous formations with discrete geological features

NASA Astrophysics Data System (ADS)

Karimi-Fard, M.; Durlofsky, L. J.

2016-10-01

A comprehensive framework for modeling flow in porous media containing thin, discrete features, which could be high-permeability fractures or low-permeability deformation bands, is presented. The key steps of the methodology are mesh generation, fine-grid discretization, upscaling, and coarse-grid discretization. Our specialized gridding technique combines a set of intersecting triangulated surfaces by constructing approximate intersections using existing edges. This procedure creates a conforming mesh of all surfaces, which defines the internal boundaries for the volumetric mesh. The flow equations are discretized on this conforming fine mesh using an optimized two-point flux finite-volume approximation. The resulting discrete model is represented by a list of control-volumes with associated positions and pore-volumes, and a list of cell-to-cell connections with associated transmissibilities. Coarse models are then constructed by the aggregation of fine-grid cells, and the transmissibilities between adjacent coarse cells are obtained using flow-based upscaling procedures. Through appropriate computation of fracture-matrix transmissibilities, a dual-continuum representation is obtained on the coarse scale in regions with connected fracture networks. The fine and coarse discrete models generated within the framework are compatible with any connectivity-based simulator. The applicability of the methodology is illustrated for several two- and three-dimensional examples. In particular, we consider gas production from naturally fractured low-permeability formations, and transport through complex fracture networks. In all cases, highly accurate solutions are obtained with significant model reduction.

A modern regional geological analysis of Venezuela - lessons from a major new world oil province on exploration in mature areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daly, M.; Audemard, F.; Valdes, G.

1993-09-01

Venezuela has produced some 44 billion bbl of oil since the early part of the century. As such, it represents one of the world's major oil producers and a mature petroleum province. However, major tracts of Venezuela's sedimentary basins remain underexplored and large discoveries are still being made in new and old reservoir systems. A regional geological analysis of Venezuela, focusing on basin evolution and sequence stratigraphy and incorporating data from the three national oil companies, is presented. The analysis presents a regionally consistent tectonostratigraphic model capable of explaining the evolution of the Mesozoic and Cenozoic basins of Venezuela andmore » placing the major reservoir facies in their regional tectonic and sequence stratigraphic context. Four regional cross sections describe the stratigraphic and structural model. The model recognizes a Jurassic rifting event and inversion, succeeded by an Early Cretaceous passive margin. In western Venezuela, the Early Cretaceous passive subsidence is enhanced locally by extension related to the Colombian active margin. Venezuela experienced a major change in the Campanian with the initial collision of the Caribbean arc, recorded by foreland structuring and widespread stratigraphic changes. From the Campanian onward, the tectonostratigraphic evolution can be modeled in terms of a progressive southeast-directed arc-continent collision and the migration of the associated foredeep and rift basins. Within the tectonic framework, the major sequence stratigraphic units are identified and the reservoir distribution interpreted. This model provides a strong predictive tool to extrapolate reservoir systems into Venezuela's underexplored areas and to readdress its traditional areas.« less

Ab initio thermodynamic model for magnesium carbonates and hydrates.

PubMed

Chaka, Anne M; Felmy, Andrew R

2014-09-04

An ab initio thermodynamic framework for predicting properties of hydrated magnesium carbonate minerals has been developed using density-functional theory linked to macroscopic thermodynamics through the experimental chemical potentials for MgO, water, and CO2. Including semiempirical dispersion via the Grimme method and small corrections to the generalized gradient approximation of Perdew, Burke, and Ernzerhof for the heat of formation yields a model with quantitative agreement for the benchmark minerals brucite, magnesite, nesquehonite, and hydromagnesite. The model shows how small differences in experimental conditions determine whether nesquehonite, hydromagnesite, or magnesite is the result of laboratory synthesis from carbonation of brucite, and what transformations are expected to occur on geological time scales. Because of the reliance on parameter-free first-principles methods, the model is reliably extensible to experimental conditions not readily accessible to experiment and to any mineral composition for which the structure is known or can be hypothesized, including structures containing defects, substitutions, or transitional structures during solid state transformations induced by temperature changes or processes such as water, CO2, or O2 diffusion. Demonstrated applications of the ab initio thermodynamic framework include an independent means to evaluate differences in thermodynamic data for lansfordite, predicting the properties of Mg analogues of Ca-based hydrated carbonates monohydrocalcite and ikaite, which have not been observed in nature, and an estimation of the thermodynamics of barringtonite from the stoichiometry and a single experimental observation.

Uncertainty and the Conceptual Site Model

NASA Astrophysics Data System (ADS)

Price, V.; Nicholson, T. J.

2007-12-01

Our focus is on uncertainties in the underlying conceptual framework upon which all subsequent steps in numerical and/or analytical modeling efforts depend. Experienced environmental modelers recognize the value of selecting an optimal conceptual model from several competing site models, but usually do not formally explore possible alternative models, in part due to incomplete or missing site data, as well as relevant regional data for establishing boundary conditions. The value in and approach for developing alternative conceptual site models (CSM) is demonstrated by analysis of case histories. These studies are based on reported flow or transport modeling in which alternative site models are formulated using data that were not available to, or not used by, the original modelers. An important concept inherent to model abstraction of these alternative conceptual models is that it is "Far better an approximate answer to the right question, which is often vague, than the exact answer to the wrong question, which can always be made precise." (Tukey, 1962) The case histories discussed here illustrate the value of formulating alternative models and evaluating them using site-specific data: (1) Charleston Naval Site where seismic characterization data allowed significant revision of the CSM and subsequent contaminant transport modeling; (2) Hanford 300-Area where surface- and ground-water interactions affecting the unsaturated zone suggested an alternative component to the site model; (3) Savannah River C-Area where a characterization report for a waste site within the modeled area was not available to the modelers, but provided significant new information requiring changes to the underlying geologic and hydrogeologic CSM's used; (4) Amargosa Desert Research Site (ADRS) where re-interpretation of resistivity sounding data and water-level data suggested an alternative geologic model. Simple 2-D spreadsheet modeling of the ADRS with the revised CSM provided an improved match to vapor-phase tritium migration. Site-specific monitoring coupled to these alternative CSM's greatly assists in conducting uncertainty assessments. (Work supported by USNRC contract NRC-04-03-061.)

Regional Jurassic geologic framework of Alabama coastal waters area and adjacent Federal waters area

USGS Publications Warehouse

Mink, R.M.; Bearden, B.L.; Mancini, E.A.

1989-01-01

To date, numerous Jurassic hydrocarbon fields and pools have been discovered in the Cotton Valley Group, Haynesville Formation, Smackover Formation and Norphlet Formation in the tri-state area of Mississippi, Alabama and Florida, and in Alabama State coastal waters and adjacent Federal waters area. Petroleum traps are basement highs, salt anticlines, faulted salt anticlines and extensional faults associated with salt movement. Reservoirs include continental and marine sandstones, limestones and dolostones. Hydrocarbon types are oil, condensate and natural gas. The onshore stratigraphic and structural information can be used to establish a regional geologic framework for the Jurassic for the State coastal waters and adjacent Federal waters areas. Evaluation of the geologic information along with the hydrocarbon data from the tri-state area indicates that at least three Jurassic hydrocarbon trends (oil, oil and gas condensate, and deep natural gas) can be identified onshore. These onshore hydrocarbon trends can be projected into the Mobile area in the Central Gulf of Mexico and into the Pensacola, Destin Dome and Apalachicola areas in the Eastern Gulf of Mexico. Substantial reserves of natural gas are expected to be present in Alabama State waters and the northern portion of the Mobile area. Significant accumulations of oil and gas condensate may be encountered in the Pensacola, Destin Dome, and Apalachicola areas. ?? 1989.

Geologic uncertainty in a regulatory environment: An example from the potential Yucca Mountain nuclear waste repository site

NASA Astrophysics Data System (ADS)

Rautman, C. A.; Treadway, A. H.

1991-11-01

Regulatory geologists are concerned with predicting the performance of sites proposed for waste disposal or for remediation of existing pollution problems. Geologic modeling of these sites requires large-scale expansion of knowledge obtained from very limited sampling. This expansion induces considerable uncertainty into the geologic models of rock properties that are required for modeling the predicted performance of the site. One method for assessing this uncertainty is through nonparametric geostatistical simulation. Simulation can produce a series of equiprobable models of a rock property of interest. Each model honors measured values at sampled locations, and each can be constructed to emulate both the univariate histogram and the spatial covariance structure of the measured data. Computing a performance model for a number of geologic simulations allows evaluation of the effects of geologic uncertainty. A site may be judged acceptable if the number of failures to meet a particular performance criterion produced by these computations is sufficiently low. A site that produces too many failures may be either unacceptable or simply inadequately described. The simulation approach to addressing geologic uncertainty is being applied to the potential high-level nuclear waste repository site at Yucca Mountain, Nevada, U.S.A. Preliminary geologic models of unsaturated permeability have been created that reproduce observed statistical properties reasonably well. A spread of unsaturated groundwater travel times has been computed that reflects the variability of those geologic models. Regions within the simulated models exhibiting the greatest variability among multiple runs are candidates for obtaining the greatest reduction in uncertainty through additional site characterization.

DFN Modeling for the Safety Case of the Final Disposal of Spent Nuclear Fuel in Olkiluoto, Finland

NASA Astrophysics Data System (ADS)

Vanhanarkaus, O.

2017-12-01

Olkiluoto Island is a site in SW Finland chosen to host a deep geological repository for high-level nuclear waste generated by nuclear power plants of power companies TVO and Fortum. Posiva, a nuclear waste management organization, submitted a construction license application for the Olkiluoto repository to the Finnish government in 2012. A key component of the license application was an integrated geological, hydrological and biological description of the Olkiluoto site. After the safety case was reviewed in 2015 by the Radiation and Nuclear Safety Authority in Finland, Posiva was granted a construction license. Posiva is now preparing an updated safety case for the operating license application to be submitted in 2022, and an update of the discrete fracture network (DFN) model used for site characterization is part of that. The first step describing and modelling the network of fractures in the Olkiluoto bedrock was DFN model version 1 (2009), which presented an initial understanding of the relationships between rock fracturing and geology at the site and identified the important primary controls on fracturing. DFN model version 2 (2012) utilized new subsurface data from additional drillholes, tunnels and excavated underground facilities in ONKALO to better understand spatial variability of the geological controls on geological and hydrogeological fracture properties. DFN version 2 connected fracture geometric and hydraulic properties to distinct tectonic domains and to larger-scale hydraulically conductive fault zones. In the version 2 DFN model, geological and hydrogeological models were developed along separate parallel tracks. The version 3 (2017) DFN model for the Olkiluoto site integrates geological and hydrogeological elements into a single consistent model used for geological, rock mechanical, hydrogeological and hydrogeochemical studies. New elements in the version 3 DFN model include a stochastic description of fractures within Brittle Fault Zones (BFZ), integration of geological and hydrostructural interpretations of BFZ, greater use of 3D geological models to better constrain the spatial variability of fracturing and fractures using hydromechanical principles to account for material behavior and in-situ stresses.

Geoethics and Forensic Geology

NASA Astrophysics Data System (ADS)

Donnelly, Laurance

2017-04-01

The International Union of Geological Sciences (IUGS), Initiative on Forensic Geology (IFG) was set up in 2011 to promote and develop the applications of geology to policing and law enforcement throughout the world. This includes the provision of crime scene examinations, searches to locate graves or items of interest that have been buried beneath the ground surface as part of a criminal act and geological trace analysis and evidence. Forensic geologists may assist the police and law enforcement in a range of ways including for example; homicide, sexual assaults, counter terrorism, kidnapping, humanitarian incidents, environmental crimes, precious minerals theft, fakes and fraudulent crimes. The objective of this paper is to consider the geoethical aspects of forensic geology. This includes both delivery to research and teaching, and contribution to the practical applications of forensic geology in case work. The case examples cited are based on the personal experiences of the authors. Often, the technical and scientific aspect of forensic geology investigation may be the most straightforward, after all, this is what the forensic geologist has been trained to do. The associated geoethical issues can be the most challenging and complex to manage. Generally, forensic geologists are driven to carry-out their research or case work with integrity, honesty and in a manner that is law abiding, professional, socially acceptable and highly responsible. This is necessary in advising law enforcement organisations, society and the scientific community that they represent. As the science of forensic geology begins to advance around the world it is desirable to establish a standard set of principles, values and to provide an agreed ethical a framework. But what are these core values? Who is responsible for producing these? How may these become enforced? What happens when geoethical standards are breached? This paper does not attempt to provide all of the answers, as further work is required. However, it draws attention to some of the relevant geoethical issues within forensic geology and forensic geoscience. This paper also highlights the need for the development of a set of resources; references and guidelines, standards and protocols, a code of conduct (including for example integrity, accountability, honesty, professional fairness, courtesy, trustworthiness), data sharing and information transparency, education and training, multi-disciplinary collaboration, development of research, fair debate, evaluating uncertainty and risk, regulation and accreditation, effective communication and diplomacy, attendance at crime scenes, presenting evidence in courts of law, dealing with the media and elimination of potential bias. The uptake of Forensic Geoscience brings with it considerable challenges arising from the direct and often very sensitive human interactions. By developing this ethical component to the work that the IUGS-IFG group does, combines technical approaches with sensitive solutions, and also in parallel helps define an ethical framework for forensic geoscientists' research and practice in addressing these challenges.

Optimal mapping of terrestrial gamma dose rates using geological parent material and aerogeophysical survey data.

PubMed

Rawlins, B G; Scheib, C; Tyler, A N; Beamish, D

2012-12-01

Regulatory authorities need ways to estimate natural terrestrial gamma radiation dose rates (nGy h⁻¹) across the landscape accurately, to assess its potential deleterious health effects. The primary method for estimating outdoor dose rate is to use an in situ detector supported 1 m above the ground, but such measurements are costly and cannot capture the landscape-scale variation in dose rates which are associated with changes in soil and parent material mineralogy. We investigate the potential for improving estimates of terrestrial gamma dose rates across Northern Ireland (13,542 km²) using measurements from 168 sites and two sources of ancillary data: (i) a map based on a simplified classification of soil parent material, and (ii) dose estimates from a national-scale, airborne radiometric survey. We used the linear mixed modelling framework in which the two ancillary variables were included in separate models as fixed effects, plus a correlation structure which captures the spatially correlated variance component. We used a cross-validation procedure to determine the magnitude of the prediction errors for the different models. We removed a random subset of 10 terrestrial measurements and formed the model from the remainder (n = 158), and then used the model to predict values at the other 10 sites. We repeated this procedure 50 times. The measurements of terrestrial dose vary between 1 and 103 (nGy h⁻¹). The median absolute model prediction errors (nGy h⁻¹) for the three models declined in the following order: no ancillary data (10.8) > simple geological classification (8.3) > airborne radiometric dose (5.4) as a single fixed effect. Estimates of airborne radiometric gamma dose rate can significantly improve the spatial prediction of terrestrial dose rate.

Terrain Models in Field Geology Courses.

ERIC Educational Resources Information Center

Whittecar, G. Richard

1984-01-01

Describes a terrain model for geologic mapping which, when combined with exercises in rock description, Brunton compass manipulation, orienteering, and geologic report writing, allows students to refine skills needed for summer field camp. Advantages and limitations of the model and its use in a field course are also discussed. (BC)

Publications - DDS 4 | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

Datasets of Alaska: Alaska Division of Geological & Geophysical Surveys Digital Data Series 4, http ; Alaska Statewide Maps; Alaska, State of; Digital Elevation Model; Digital Surface Model (DSM); Geologic

Groundwater vulnerability to onshore unconventional and conventional hydrocarbon activities in England

NASA Astrophysics Data System (ADS)

Loveless, Sian; Bloomfield, John; Ward, Rob; Davey, Ian; Hart, Alwyn

2016-04-01

In the last five years there has been a renewed interest in onshore oil and gas in England as new extraction technologies and continued energy demand have allowed for the development of less accessible resources. Until now, shale gas has received most attention in England although exploration licences have also been granted for coal bed methane and mine gas in addition to more conventional hydrocarbon resources. While there is some interest in underground coal gasification there are currently no licences granted. Potential impacts on groundwater from shale gas operations have been well publicised. Hazards include contamination from spills or leaks of frack-fluids and returned water, at the surface, through leaky wells or via subsurface pathways from the source rock, and the availability of water resources. Groundwater is an important resource in England, providing an average of 31% of water resources in England and Wales, and up to 100% in some areas of south-east England. In its role as the environmental regulator the Environment Agency must manage the risks associated with these hazards, and those associated with other onshore oil and gas activities, so that they are minimised. Here we focus on the groundwater contamination risk from source rocks though subsurface pathways. Despite the abundant literature emerging from the North American continent there remain great uncertainties as to the risk. These uncertainties are amplified when translated to Europe due to significant policy and geological differences. Research from North America indicates that risk is influenced by the exploitation and well completion methods and the geological setting, including: pre-existing fracture and fault networks; stress regime; petrological and rheological properties of the rock between the source and groundwater receptor and the distance between the source and receptors. A joint British Geological Survey/ EA project - iHydrogeology (http://www.bgs.ac.uk/research/groundwater/shaleGas/iHydrogeology.html) - identified key shale units and Principal Aquifers (http://apps.environment-agency.gov.uk/wiyby/117020.aspx) in England and Wales. The BGS GB3D model (Mathers et al., 2014) was used to produce maps of these and the separation distance between aquifer-shale pairs. The latter maps show large variations across the country and even within basins for the aquifer-shale pairs. For example, the separation distance between the Bowland shale and Triassic sandstone aquifer varies between < 200 m to > 1,500 m. However it is not yet clear what constitutes a safe separation distance. Due to the geological variability across England a current project (3DGWV) will address the need to assess risk and uncertainties both conceptually and on a more site-specific scale. The method above will be extended to other onshore hydrocarbons. Conceptual models of these source releases and pathways will be compared in the context of English geology. Another important outcome of the ihydrogeology project was the recognition that the definition of groundwater bodies with respect to the Water Framework Directive might need to be redefined in a UK context, taking into account these new, 3D risks. In addition to this work the BGS and EA are also conducting one of the first comprehensive baseline monitoring studies in potential shale gas areas and a project looking at the impacts of abandoned wells. Reference: Mathers, et al. (2014). GB3D-a framework for the bedrock geology of Great Britain. Geoscience Data Journal, 1(1), 30-42.

Geologic cross section D-D' through the Appalachian basin from the Findlay arch, Sandusky County, Ohio, to the Valley and Ridge province, Hardy County, West Virginia: Chapter E.4.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

USGS Publications Warehouse

Ryder, Robert T.; Crangle, Robert D.; Trippi, Michael H.; Swezey, Christopher S.; Lentz, Erika E.; Rowan, Elisabeth L.; Hope, Rebecca S.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

This chapter is a re-release of U.S. Geological Survey Scientific Investigations Map 3067, of the same title, by Ryder and others (2009). For this chapter, two appendixes have been added that do not appear with the original version. Appendix A provides Log ASCII Standard (LAS) files for each drill hole along cross-section D-D'; they are text files which encode gamma-ray, neutron, density, and other logs that can be used by most well-logging software. Appendix B provides graphic well-log traces and lithologic descriptions with formation tops from each drill hole.

Cruise to the Chukchi Borderland, Arctic Ocean

USGS Publications Warehouse

Grantz, Arthur; ,

1993-01-01

Oceanography and geology were the principal focuses of the U.S. Geological Survey-sponsored expedition Arctic Summer West '92, which traveled to the eastern part of the Chukchi Borderland of the Amerasia Basin, western Arctic Ocean. The expedition took place from August 20 to September 25, 1992, aboard the Coast Guard cutter Polar Star. USGS investigated the geologic framework and tectonic origin of the borderland, Arctic Quaternary paleoclimate, sea-ice transport of particulate matter in the Beaufort Gyre, and possible radionuclide contamination of the water column and seafloor off Alaska from sources in the Russian Arctic. Researchers from five other institutions studied the area's oceanography, age of the water column, paleoenvironment of the Holocene sediment, physical properties and synthetic-aperture radar backscatter of sea ice, and the drop-stone content of late Quaternary sediment.

Overview of geology and tectonic evolution of the Baikal-Tuva area.

PubMed

Gladkochub, Dmitry; Donskaya, Tatiana

2009-01-01

This chapter provides the results of geological investigations of the main tectonic units of the Baikal-Tuva region (southwestern part of Siberia) during the last decades: the ancient Siberian craton and adjacent areas of the Central Asian Orogenic belt. In the framework of these main units we describe small-scale blocks (terranes) with focus on details of their inner structure and evolution through time. As well as describing the geology and tectonics of the area studied, we give an overview of underwater sediments, neotectonics, and some phenomena of history and development of the Baikal, Khubsugul, Chargytai, and Tore-Chol Lakes basins of the Baikal-Tuva region. It is suggested that these lakes' evolution was controlled by neotectonic processes, modern seismic activity, and global climate changes.

Helicopter Electromagnetic Surveys for Hydrological Framework Studies in Nebraska

NASA Astrophysics Data System (ADS)

Smith, B. D.; Abraham, J. A.; Cannia, J. C.; Steele, G. V.; Peterson, S. M.

2008-12-01

Management and allocation of water resources in Nebraska is based in part on understanding the relation between surface-water and ground-water systems. To help understand these complex relations, the U.S. Geological Survey (USGS) conducted airborne resistivity and magnetic (frequency domain helicopter electromagnetic, HEM) surveys in Eastern (2007) and Western (2008) Nebraska. These surveys were integrated with hydrologic studies (aquifer characteristics and modeling), and ground and borehole geophysical surveys to characterize and map the hydrogeologic framework in three-dimensions. The three study areas selected in Eastern Nebraska (Ashland, Firth, and Oakland) have glacial terrains and bedrock that typify different hydrogeologic settings for surface and ground water. The Eastern Nebraska Water Resources Assessment is a joint State of Nebraska and USGS study including the Conservation and Survey Division (University of Nebraska) and the following Natural Resources Districts (NRD): Lower Platte South, Lower Platte North, Lower Elkhorn, Lewis and Clark, Nemaha, and Papio-Missouri River. Approximately 600 line km were flown with HEM in each of the three glacial terrains with a line spacing of approximately 270 m and samples every three meters. One dimensional imaging was done along the flight lines for the HEM in each area. Models were compared to ground resistivity and time domain electromagnetic soundings and to borehole lithologic and geophysical logs. The map of the subsurface hydrogeologic properties inferred from the HEM modeling significantly improves the resolution of hydrologic models and understanding of ground-water resources. Surveys in western Nebraska panhandle, were done along the North Platte River and Lodgepole Creek Valleys. The geology consists of Quaternary alluvium, and interbeded Tertiary sandstones and siltstones above Cretaceous shale. The Quaternary alluvium comprises the primary aquifer in the North Platte River Valley, whereas thin alluvial sediments and Tertiary sandstone channels comprise the primary aquifers in Lodgepole Creek Valley. Locally, Tertiary Siltstone and Cretaceous shale is weathered and incised. A prominent factor in the hydrologic setting of the North Platte River Valley is recharge through un-lined irrigation canals. Surveys in western Nebraska were funded by the North Platte and South Platte NRDs. These NRDS have employed the best in science-based integrated water resources management. The ground-water flow modeling study in western Nebraska will use the HEM data as part of model datasets, to create a tool used to evaluate implications of water management options over most of the surface-water irrigated area.

Geology and religion - historical perspective and current problems

NASA Astrophysics Data System (ADS)

Kölbl-Ebert, Martina

2010-05-01

Today, when referring to the relationship between geology and religion, people usually at once think of Christian (and other) fundamentalists and their chronic palaeontological illiteracy leading to Creationism, to Intelligent Design, and a distrust of science in general among them most prominently geology, palaeontology and evolutionary biology. Thus the relationship of geology and religion is usually considered to be under strain. In former times things used to be quite different, and for most of human history the observation of geological phenomena and the acquisition of geological expertise was intimately connected with religious ideas. The Judeo-Christian sense of a finite Earth history prepared the ground for accepting the Earth's different strata as testimony to the development of our globe through time. It was this religious, theological framework, from which the early geology started to evolve. However, with increasing observations there was a growing mismatch between what was expected according to ancient, scriptural authorities and the actual data. The release of geology from religious connotations or associations was a development closely connected with the Enlightenment, when geology and religion started to drift apart not with a violent rupture but in a subtle and sometimes circuitous manner. However, outside the group of people with geological expertise, not all was smooth and peaceful, and some conservative clergymen as well as laypersons were rather shocked by the new ideas that came with geology: the immensity of the timescale, a dynamic Earth, not just a ruin shaped by the Deluge, and a dynamic biology too with the Darwinian theory of evolution, which was founded in part on palaeontological evidence and the assumption of a long geological time scale. Nevertheless and interestingly the Creationism we face today is a rather recent phenomenon influenced by a number of motives, most of them philosophical and theological in nature. And so, the current debate, if there has to be one, should not be about geology versus theology but about enlightenment versus fundamentalism. It is important that geologists should be aware that many theologians are just as appalled by the recent rise of Christian fundamentalism as they are. Probably the best remedy is to engage in dialogue with those many open-minded philosophers and theologians rather than frighten them off with a militant atheist stance, bearing in mind that dialogue requires first of all respect for the intellectual achievements of the other but also a common language to avoid misunderstandings. Two seemingly trivial words, "chance" and "design", often seem to be the core of such misunderstandings. While for a palaeontologist or biologist, it is quite possible to talk about chance and design within an evolutionary framework, e.g. undirected mutations and natural selection leading to the body-plan of certain organisms, i.e. chance and necessity leading to design, these two terms exclude each other for most theologians. "Design" for them is synonymous to "purpose", while a chance event in theology is per definition without sense and purpose. Whenever we as scientists talk of "chance", a theologian suspects that we explicitly exclude god, while we are convinced that we have not made any statement about god at all.

Unification of small and large time scales for biological evolution: deviations from power law.

PubMed

Chowdhury, Debashish; Stauffer, Dietrich; Kunwar, Ambarish

2003-02-14

We develop a unified model that describes both "micro" and "macro" evolutions within a single theoretical framework. The ecosystem is described as a dynamic network; the population dynamics at each node of this network describes the "microevolution" over ecological time scales (i.e., birth, ageing, and natural death of individual organisms), while the appearance of new nodes, the slow changes of the links, and the disappearance of existing nodes accounts for the "macroevolution" over geological time scales (i.e., the origination, evolution, and extinction of species). In contrast to several earlier claims in the literature, we observe strong deviations from power law in the regime of long lifetimes.