NASA Astrophysics Data System (ADS)
Mekonnen, M. M.; Hoekstra, A. Y. Y.
2014-12-01
We estimated anthropogenic phosphorus (P) loads to freshwater, globally at a spatial resolution level of 5 by 5 arc minute. The global anthropogenic P load to freshwater systems from both diffuse and point sources in the period 2002-2010 was 1.5 million tonnes per year. China contributed about 30% to this global anthropogenic P load. India was the second largest contributor (8%), followed by the USA (7%), Spain and Brazil each contributing 6% to the total. The domestic sector contributed the largest share (54%) to this total followed by agriculture (38%) and industry (8%). Among the crops, production of cereals had the largest contribution to the P loads (32%), followed by fruits, vegetables, and oil crops, each contributing about 15% to the total. We also calculated the resultant grey water footprints, and relate the grey water footprints per river basin to runoff to calculate the P-related water pollution level (WPL) per catchment.
Noise effects on the health status in a dynamic failure model for living organisms
NASA Astrophysics Data System (ADS)
Kang, H.; Jo, J.; Choi, M. Y.; Choi, J.; Yoon, B.-G.
2007-03-01
We study internal and external noise effects on the healthy-unhealthy transition and related phenomena in a dynamic failure model for living organisms. It is found that internal noise makes the system weaker, leading to breakdown under smaller stress. The discontinuous healthy-unhealthy transition in a system with global load sharing below a critical point is naturally explained in terms of the bistability for the health status. External noise present in constant stress gives similar results; further, it induces resonance in response to periodic stress, regardless of load transfer. In the case of local load sharing, such periodic stress is revealed more hazardous than the constant stress.
Global Cryptosporidium Loads from Livestock Manure.
Vermeulen, Lucie C; Benders, Jorien; Medema, Gertjan; Hofstra, Nynke
2017-08-01
Understanding the environmental pathways of Cryptosporidium is essential for effective management of human and animal cryptosporidiosis. In this paper we aim to quantify livestock Cryptosporidium spp. loads to land on a global scale using spatially explicit process-based modeling, and to explore the effect of manure storage and treatment on oocyst loads using scenario analysis. Our model GloWPa-Crypto L1 calculates a total global Cryptosporidium spp. load from livestock manure of 3.2 × 10 23 oocysts per year. Cattle, especially calves, are the largest contributors, followed by chickens and pigs. Spatial differences are linked to animal spatial distributions. North America, Europe, and Oceania together account for nearly a quarter of the total oocyst load, meaning that the developing world accounts for the largest share. GloWPa-Crypto L1 is most sensitive to oocyst excretion rates, due to large variation reported in literature. We compared the current situation to four alternative management scenarios. We find that although manure storage halves oocyst loads, manure treatment, especially of cattle manure and particularly at elevated temperatures, has a larger load reduction potential than manure storage (up to 4.6 log units). Regions with high reduction potential include India, Bangladesh, western Europe, China, several countries in Africa, and New Zealand.
Global Cryptosporidium Loads from Livestock Manure
2017-01-01
Understanding the environmental pathways of Cryptosporidium is essential for effective management of human and animal cryptosporidiosis. In this paper we aim to quantify livestock Cryptosporidium spp. loads to land on a global scale using spatially explicit process-based modeling, and to explore the effect of manure storage and treatment on oocyst loads using scenario analysis. Our model GloWPa-Crypto L1 calculates a total global Cryptosporidium spp. load from livestock manure of 3.2 × 1023 oocysts per year. Cattle, especially calves, are the largest contributors, followed by chickens and pigs. Spatial differences are linked to animal spatial distributions. North America, Europe, and Oceania together account for nearly a quarter of the total oocyst load, meaning that the developing world accounts for the largest share. GloWPa-Crypto L1 is most sensitive to oocyst excretion rates, due to large variation reported in literature. We compared the current situation to four alternative management scenarios. We find that although manure storage halves oocyst loads, manure treatment, especially of cattle manure and particularly at elevated temperatures, has a larger load reduction potential than manure storage (up to 4.6 log units). Regions with high reduction potential include India, Bangladesh, western Europe, China, several countries in Africa, and New Zealand. PMID:28654242
Failure criterion for materials with spatially correlated mechanical properties
NASA Astrophysics Data System (ADS)
Faillettaz, J.; Or, D.
2015-03-01
The role of spatially correlated mechanical elements in the failure behavior of heterogeneous materials represented by fiber bundle models (FBMs) was evaluated systematically for different load redistribution rules. Increasing the range of spatial correlation for FBMs with local load sharing is marked by a transition from ductilelike failure characteristics into brittlelike failure. The study identified a global failure criterion based on macroscopic properties (external load and cumulative damage) that is independent of spatial correlation or load redistribution rules. This general metric could be applied to assess the mechanical stability of complex and heterogeneous systems and thus provide an important component for early warning of a class of geophysical ruptures.
NASA Astrophysics Data System (ADS)
Keener, V. W.; Feyereisen, G. W.; Lall, U.; Jones, J. W.; Bosch, D. D.; Lowrance, R.
2010-02-01
SummaryAs climate variability increases, it is becoming increasingly critical to find predictable patterns that can still be identified despite overall uncertainty. The El-Niño/Southern Oscillation is the best known pattern. Its global effects on weather, hydrology, ecology and human health have been well documented. Climate variability manifested through ENSO has strong effects in the southeast United States, seen in precipitation and stream flow data. However, climate variability may also affect water quality in nutrient concentrations and loads, and have impacts on ecosystems, health, and food availability in the southeast. In this research, we establish a teleconnection between ENSO and the Little River Watershed (LRW), GA., as seen in a shared 3-7 year mode of variability for precipitation, stream flow, and nutrient load time series. Univariate wavelet analysis of the NINO 3.4 index of sea surface temperature (SST) and of precipitation, stream flow, NO 3 concentration and load time series from the watershed was used to identify common signals. Shared 3-7 year modes of variability were seen in all variables, most strongly in precipitation, stream flow and nutrient load in strong El Niño years. The significance of shared 3-7 year periodicity over red noise with 95% confidence in SST and precipitation, stream flow, and NO 3 load time series was confirmed through cross-wavelet and wavelet-coherence transforms, in which common high power and co-variance were computed for each set of data. The strongest 3-7 year shared power was seen in SST and stream flow data, while the strongest co-variance was seen in SST and NO 3 load data. The strongest cross-correlation was seen as a positive value between the NINO 3.4 and NO 3 load with a three-month lag. The teleconnection seen in the LRW between the NINO 3.4 index and precipitation, stream flow, and NO 3 load can be utilized in a model to predict monthly nutrient loads based on short-term climate variability, facilitating management in high risk seasons.
Revisiting control establishments for emerging energy hubs
NASA Astrophysics Data System (ADS)
Nasirian, Vahidreza
Emerging small-scale energy systems, i.e., microgrids and smartgrids, rely on centralized controllers for voltage regulation, load sharing, and economic dispatch. However, the central controller is a single-point-of-failure in such a design as either the controller or attached communication links failure can render the entire system inoperable. This work seeks for alternative distributed control structures to improve system reliability and help to the scalability of the system. A cooperative distributed controller is proposed that uses a noise-resilient voltage estimator and handles global voltage regulation and load sharing across a DC microgrid. Distributed adaptive droop control is also investigated as an alternative solution. A droop-free distributed control is offered to handle voltage/frequency regulation and load sharing in AC systems. This solution does not require frequency measurement and, thus, features a fast frequency regulation. Distributed economic dispatch is also studied, where a distributed protocol is designed that controls generation units to merge their incremental costs into a consensus and, thus, push the entire system to generate with the minimum cost. Experimental verifications and Hardware-in-the-Loop (HIL) simulations are used to study efficacy of the proposed control protocols.
A Method to Analyze and Optimize the Load Sharing of Split Path Transmissions
NASA Technical Reports Server (NTRS)
Krantz, Timothy L.
1996-01-01
Split-path transmissions are promising alternatives to the common planetary transmissions for rotorcraft. Heretofore, split-path designs proposed for or used in rotorcraft have featured load-sharing devices that add undesirable weight and complexity to the designs. A method was developed to analyze and optimize the load sharing in split-path transmissions without load-sharing devices. The method uses the clocking angle as a design parameter to optimize for equal load sharing. In addition, the clocking angle tolerance necessary to maintain acceptable load sharing can be calculated. The method evaluates the effects of gear-shaft twisting and bending, tooth bending, Hertzian deformations within bearings, and movement of bearing supports on load sharing. It was used to study the NASA split-path test gearbox and the U.S. Army's Comanche helicopter main rotor gearbox. Acceptable load sharing was found to be achievable and maintainable by using proven manufacturing processes. The analytical results compare favorably to available experimental data.
NASA Astrophysics Data System (ADS)
Dong, Hao; Hu, Yahui
2018-04-01
The bend-torsion coupling dynamics load-sharing model of the helicopter face gear split torque transmission system is established by using concentrated quality standard, to analyzing the dynamic load-sharing characteristic. The mathematical models include nonlinear support stiffness, time-varying meshing stiffness, damping, gear backlash. The results showed that the errors collectively influenced the load sharing characteristics, only reduce a certain error, it is never fully reached the perfect loading sharing characteristics. The system load-sharing performance can be improved through floating shaft support. The above-method will provide a theoretical basis and data support for its dynamic performance optimization design.
Axial calibration methods of piezoelectric load sharing dynamometer
NASA Astrophysics Data System (ADS)
Zhang, Jun; Chang, Qingbing; Ren, Zongjin; Shao, Jun; Wang, Xinlei; Tian, Yu
2018-06-01
The relationship between input and output of load sharing dynamometer is seriously non-linear in different loading points of a plane, so it's significant for accutately measuring force to precisely calibrate the non-linear relationship. In this paper, firstly, based on piezoelectric load sharing dynamometer, calibration experiments of different loading points are performed in a plane. And then load sharing testing system is respectively calibrated based on BP algorithm and ELM (Extreme Learning Machine) algorithm. Finally, the results show that the calibration result of ELM is better than BP for calibrating the non-linear relationship between input and output of loading sharing dynamometer in the different loading points of a plane, which verifies that ELM algorithm is feasible in solving force non-linear measurement problem.
Alonso-Perez, Elisa; Suarez-Gestal, Marian; Calaza, Manuel; Blanco, Francisco J; Suarez, Ana; Santos, Maria Jose; Papasteriades, Chryssa; Carreira, Patricia; Pullmann, Rudolf; Ordi-Ros, Josep; Marchini, Maurizio; Skopouli, Fotini N; Bijl, Marc; Barrizone, Nadia; Sebastiani, Gian Domenico; Migliaresi, Sergio; Witte, Torsten; Lauwerys, Bernard R; Kovacs, Attila; Ruzickova, Sarka; Gomez-Reino, Juan J; Gonzalez, Antonio
2014-06-19
We aimed to replicate a recent study which showed higher genetic risk load at 15 loci in men than in women with systemic lupus erythematosus (SLE). This difference was very significant, and it was interpreted as indicating that men require more genetic susceptibility than women to develop SLE. Nineteen SLE-associated loci (thirteen of which are shared with the previous study) were analyzed in 1,457 SLE patients and 1,728 healthy controls of European ancestry. Genetic risk load was calculated as sex-specific sum genetic risk scores (GRS(s)). Our results did not replicate those of the previous study at either the level of individual loci or the global level of GRS(s). GRS(s) were larger in women than in men (4.20 ± 1.07 in women vs. 3.27 ± 0.98 in men). This very significant difference (P < 10(-16)) was more dependent on the six new loci not included in the previous study (59% of the difference) than on the thirteen loci that are shared (the remaining 41%). However, the 13 shared loci also showed a higher genetic risk load in women than in men in our study (P = 6.6 × 10(-7)), suggesting that heterogeneity of participants, in addition to different loci, contributed to the opposite results. Our results show the lack of a clear trend toward higher genetic risk in one of the sexes for the analyzed SLE loci. They also highlight several limitations of assessments of genetic risk load, including the possibility of ascertainment bias with loci discovered in studies that have included mainly women.
2014-01-01
Introduction We aimed to replicate a recent study which showed higher genetic risk load at 15 loci in men than in women with systemic lupus erythematosus (SLE). This difference was very significant, and it was interpreted as indicating that men require more genetic susceptibility than women to develop SLE. Methods Nineteen SLE-associated loci (thirteen of which are shared with the previous study) were analyzed in 1,457 SLE patients and 1,728 healthy controls of European ancestry. Genetic risk load was calculated as sex-specific sum genetic risk scores (GRSs). Results Our results did not replicate those of the previous study at either the level of individual loci or the global level of GRSs. GRSs were larger in women than in men (4.20 ± 1.07 in women vs. 3.27 ± 0.98 in men). This very significant difference (P < 10−16) was more dependent on the six new loci not included in the previous study (59% of the difference) than on the thirteen loci that are shared (the remaining 41%). However, the 13 shared loci also showed a higher genetic risk load in women than in men in our study (P = 6.6 × 10−7), suggesting that heterogeneity of participants, in addition to different loci, contributed to the opposite results. Conclusion Our results show the lack of a clear trend toward higher genetic risk in one of the sexes for the analyzed SLE loci. They also highlight several limitations of assessments of genetic risk load, including the possibility of ascertainment bias with loci discovered in studies that have included mainly women. PMID:24946689
Li, Ying-Jun; Yang, Cong; Wang, Gui-Cong; Zhang, Hui; Cui, Huan-Yong; Zhang, Yong-Liang
2017-09-01
This paper presents a novel integrated piezoelectric six-dimensional force sensor which can realize dynamic measurement of multi-dimensional space load. Firstly, the composition of the sensor, the spatial layout of force-sensitive components, and measurement principle are analyzed and designed. There is no interference of piezoelectric six-dimensional force sensor in theoretical analysis. Based on the principle of actual work and deformation compatibility coherence, this paper deduces the parallel load sharing principle of the piezoelectric six-dimensional force sensor. The main effect factors which affect the load sharing ratio are obtained. The finite element model of the piezoelectric six-dimensional force sensor is established. In order to verify the load sharing principle of the sensor, a load sharing test device of piezoelectric force sensor is designed and fabricated. The load sharing experimental platform is set up. The experimental results are in accordance with the theoretical analysis and simulation results. The experiments show that the multi-dimensional and heavy force measurement can be realized by the parallel arrangement of the load sharing ring and the force sensitive element in the novel integrated piezoelectric six-dimensional force sensor. The ideal load sharing effect of the sensor can be achieved by appropriate size parameters. This paper has an important guide for the design of the force measuring device according to the load sharing mode. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.
Split torque transmission load sharing
NASA Technical Reports Server (NTRS)
Krantz, T. L.; Rashidi, M.; Kish, J. G.
1992-01-01
Split torque transmissions are attractive alternatives to conventional planetary designs for helicopter transmissions. The split torque designs can offer lighter weight and fewer parts but have not been used extensively for lack of experience, especially with obtaining proper load sharing. Two split torque designs that use different load sharing methods have been studied. Precise indexing and alignment of the geartrain to produce acceptable load sharing has been demonstrated. An elastomeric torque splitter that has large torsional compliance and damping produces even better load sharing while reducing dynamic transmission error and noise. However, the elastomeric torque splitter as now configured is not capable over the full range of operating conditions of a fielded system. A thrust balancing load sharing device was evaluated. Friction forces that oppose the motion of the balance mechanism are significant. A static analysis suggests increasing the helix angle of the input pinion of the thrust balancing design. Also, dynamic analysis of this design predicts good load sharing and significant torsional response to accumulative pitch errors of the gears.
Heat Load Sharing in a Capillary Pumped Loop with Multiple Evaporators and Multiple Condensers
NASA Technical Reports Server (NTRS)
Ku, Jentung
2005-01-01
This paper describes the heat load sharing function among multiple parallel evaporators in a capillary pumped loop (CPL). In the normal mode of operation, the evaporators cool the instruments by absorbing the waste heat. When an instruments is turned off, the attached evaporator can keep it warm by receiving heat from other evaporators serving the operating instruments. This is referred to as heat load sharing. A theoretical basis of heat load sharing is given first. The fact that the wicks in the powered evaporators will develop capillary pressure to force the generated vapor to flow to cold locations where the pressure is lower leads to the conclusion that heat load sharing is an inherent function of a CPL with multiple evaporators. Heat load sharing has been verified with many CPLs in ground tests. Experimental results of the Capillary Pumped Loop 3 (CAPL 3) Flight Experiment are presented in this paper. Factors that affect the amount of heat being shared are discussed. Some constraints of heat load sharing are also addressed.
Vehicle-to-Grid Automatic Load Sharing with Driver Preference in Micro-Grids
DOE Office of Scientific and Technical Information (OSTI.GOV)
Wang, Yubo; Nazaripouya, Hamidreza; Chu, Chi-Cheng
Integration of Electrical Vehicles (EVs) with power grid not only brings new challenges for load management, but also opportunities for distributed storage and generation. This paper comprehensively models and analyzes distributed Vehicle-to-Grid (V2G) for automatic load sharing with driver preference. In a micro-grid with limited communications, V2G EVs need to decide load sharing based on their own power and voltage profile. A droop based controller taking into account driver preference is proposed in this paper to address the distributed control of EVs. Simulations are designed for three fundamental V2G automatic load sharing scenarios that include all system dynamics of suchmore » applications. Simulation results demonstrate that active power sharing is achieved proportionally among V2G EVs with consideration of driver preference. In additional, the results also verify the system stability and reactive power sharing analysis in system modelling, which sheds light on large scale V2G automatic load sharing in more complicated cases.« less
Local load-sharing fiber bundle model in higher dimensions.
Sinha, Santanu; Kjellstadli, Jonas T; Hansen, Alex
2015-08-01
We consider the local load-sharing fiber bundle model in one to five dimensions. Depending on the breaking threshold distribution of the fibers, there is a transition where the fracture process becomes localized. In the localized phase, the model behaves as the invasion percolation model. The difference between the local load-sharing fiber bundle model and the equal load-sharing fiber bundle model vanishes with increasing dimensionality with the characteristics of a power law.
Load Sharing Behavior of Star Gearing Reducer for Geared Turbofan Engine
NASA Astrophysics Data System (ADS)
Mo, Shuai; Zhang, Yidu; Wu, Qiong; Wang, Feiming; Matsumura, Shigeki; Houjoh, Haruo
2017-07-01
Load sharing behavior is very important for power-split gearing system, star gearing reducer as a new type and special transmission system can be used in many industry fields. However, there is few literature regarding the key multiple-split load sharing issue in main gearbox used in new type geared turbofan engine. Further mechanism analysis are made on load sharing behavior among star gears of star gearing reducer for geared turbofan engine. Comprehensive meshing error analysis are conducted on eccentricity error, gear thickness error, base pitch error, assembly error, and bearing error of star gearing reducer respectively. Floating meshing error resulting from meshing clearance variation caused by the simultaneous floating of sun gear and annular gear are taken into account. A refined mathematical model for load sharing coefficient calculation is established in consideration of different meshing stiffness and supporting stiffness for components. The regular curves of load sharing coefficient under the influence of interactions, single action and single variation of various component errors are obtained. The accurate sensitivity of load sharing coefficient toward different errors is mastered. The load sharing coefficient of star gearing reducer is 1.033 and the maximum meshing force in gear tooth is about 3010 N. This paper provides scientific theory evidences for optimal parameter design and proper tolerance distribution in advanced development and manufacturing process, so as to achieve optimal effects in economy and technology.
Uncertainty propagation through an aeroelastic wind turbine model using polynomial surrogates
DOE Office of Scientific and Technical Information (OSTI.GOV)
Murcia, Juan Pablo; Réthoré, Pierre-Elouan; Dimitrov, Nikolay
Polynomial surrogates are used to characterize the energy production and lifetime equivalent fatigue loads for different components of the DTU 10 MW reference wind turbine under realistic atmospheric conditions. The variability caused by different turbulent inflow fields are captured by creating independent surrogates for the mean and standard deviation of each output with respect to the inflow realizations. A global sensitivity analysis shows that the turbulent inflow realization has a bigger impact on the total distribution of equivalent fatigue loads than the shear coefficient or yaw miss-alignment. The methodology presented extends the deterministic power and thrust coefficient curves to uncertaintymore » models and adds new variables like damage equivalent fatigue loads in different components of the turbine. These surrogate models can then be implemented inside other work-flows such as: estimation of the uncertainty in annual energy production due to wind resource variability and/or robust wind power plant layout optimization. It can be concluded that it is possible to capture the global behavior of a modern wind turbine and its uncertainty under realistic inflow conditions using polynomial response surfaces. In conclusion, the surrogates are a way to obtain power and load estimation under site specific characteristics without sharing the proprietary aeroelastic design.« less
Uncertainty propagation through an aeroelastic wind turbine model using polynomial surrogates
Murcia, Juan Pablo; Réthoré, Pierre-Elouan; Dimitrov, Nikolay; ...
2017-07-17
Polynomial surrogates are used to characterize the energy production and lifetime equivalent fatigue loads for different components of the DTU 10 MW reference wind turbine under realistic atmospheric conditions. The variability caused by different turbulent inflow fields are captured by creating independent surrogates for the mean and standard deviation of each output with respect to the inflow realizations. A global sensitivity analysis shows that the turbulent inflow realization has a bigger impact on the total distribution of equivalent fatigue loads than the shear coefficient or yaw miss-alignment. The methodology presented extends the deterministic power and thrust coefficient curves to uncertaintymore » models and adds new variables like damage equivalent fatigue loads in different components of the turbine. These surrogate models can then be implemented inside other work-flows such as: estimation of the uncertainty in annual energy production due to wind resource variability and/or robust wind power plant layout optimization. It can be concluded that it is possible to capture the global behavior of a modern wind turbine and its uncertainty under realistic inflow conditions using polynomial response surfaces. In conclusion, the surrogates are a way to obtain power and load estimation under site specific characteristics without sharing the proprietary aeroelastic design.« less
NASA Astrophysics Data System (ADS)
Bacca, Mattia; Booth, Jamie A.; Turner, Kimberly L.; McMeeking, Robert M.
2016-11-01
Bio-inspired fibrillar adhesives rely on the utilization of short-range intermolecular forces harnessed by intimate contact at fibril tips. The combined adhesive strength of multiple fibrils can only be utilized if equal load sharing (ELS) is obtained at detachment. Previous investigations have highlighted that mechanical coupling of fibrils through a compliant backing layer gives rise to load concentration and the nucleation and propagation of interfacial flaws. However, misalignment of the adhesive and contacting surface has not been considered in theoretical treatments of load sharing with backing layer interactions. Alignment imperfections are difficult to avoid for a flat-on-flat interfacial configuration. In this work we demonstrate that interfacial misalignment can significantly alter load sharing and the kinematics of detachment in a model adhesive system. Load sharing regimes dominated by backing layer interactions and misalignment are revealed, the transition between which is controlled by the misalignment angle, fibril separation, and fibril compliance. In the regime dominated by misalignment, backing layer deformation can counteract misalignment giving rise to improved load sharing when compared to an identical fibrillar array with a rigid backing layer. This result challenges the conventional belief that stiffer (and thinner) backing layers consistently reduce load concentration among fibrils. Finally, we obtain analytically the fibril compliance distribution required to harness backing layer interactions to obtain ELS. Through fibril compliance optimization, ELS can be obtained even with misalignment. However, since misalignment is typically not deterministic, it is of greater practical significance that the array optimized for perfect alignment exhibits load sharing superior to that of a homogeneous array subject to misalignment. These results inform the design of fibrillar arrays with graded compliance capable of exhibiting improved load sharing over large areas.
Unstructured P2P Network Load Balance Strategy Based on Multilevel Partitioning of Hypergraph
NASA Astrophysics Data System (ADS)
Feng, Lv; Chunlin, Gao; Kaiyang, Ma
2017-05-01
With rapid development of computer performance and distributed technology, P2P-based resource sharing mode plays important role in Internet. P2P network users continued to increase so the high dynamic characteristics of the system determine that it is difficult to obtain the load of other nodes. Therefore, a dynamic load balance strategy based on hypergraph is proposed in this article. The scheme develops from the idea of hypergraph theory in multilevel partitioning. It adopts optimized multilevel partitioning algorithms to partition P2P network into several small areas, and assigns each area a supernode for the management and load transferring of the nodes in this area. In the case of global scheduling is difficult to be achieved, the priority of a number of small range of load balancing can be ensured first. By the node load balance in each small area the whole network can achieve relative load balance. The experiments indicate that the load distribution of network nodes in our scheme is obviously compacter. It effectively solves the unbalanced problems in P2P network, which also improve the scalability and bandwidth utilization of system.
NASA Astrophysics Data System (ADS)
Liu, Wei; Li, Ying-jun; Jia, Zhen-yuan; Zhang, Jun; Qian, Min
2011-01-01
In working process of huge heavy-load manipulators, such as the free forging machine, hydraulic die-forging press, forging manipulator, heavy grasping manipulator, large displacement manipulator, measurement of six-dimensional heavy force/torque and real-time force feedback of the operation interface are basis to realize coordinate operation control and force compliance control. It is also an effective way to raise the control accuracy and achieve highly efficient manufacturing. Facing to solve dynamic measurement problem on six-dimensional time-varying heavy load in extremely manufacturing process, the novel principle of parallel load sharing on six-dimensional heavy force/torque is put forward. The measuring principle of six-dimensional force sensor is analyzed, and the spatial model is built and decoupled. The load sharing ratios are analyzed and calculated in vertical and horizontal directions. The mapping relationship between six-dimensional heavy force/torque value to be measured and output force value is built. The finite element model of parallel piezoelectric six-dimensional heavy force/torque sensor is set up, and its static characteristics are analyzed by ANSYS software. The main parameters, which affect load sharing ratio, are analyzed. The experiments for load sharing with different diameters of parallel axis are designed. The results show that the six-dimensional heavy force/torque sensor has good linearity. Non-linearity errors are less than 1%. The parallel axis makes good effect of load sharing. The larger the diameter is, the better the load sharing effect is. The results of experiments are in accordance with the FEM analysis. The sensor has advantages of large measuring range, good linearity, high inherent frequency, and high rigidity. It can be widely used in extreme environments for real-time accurate measurement of six-dimensional time-varying huge loads on manipulators.
ERIC Educational Resources Information Center
Hsiao, Ya-Ping; Brouns, Francis; van Bruggen, Jan; Sloep, Peter B.
2012-01-01
In Learning Networks, learners need to share knowledge with others to build knowledge. In particular, when working on complex tasks, they often need to acquire extra cognitive resources from others to process a high task load. However, without support high task load and organizing knowledge sharing themselves might easily overload learners'…
DOE Office of Scientific and Technical Information (OSTI.GOV)
Guo, Y.; Keller, J.; LaCava, W.
2012-09-01
This computational work investigates planetary gear load sharing of three-mount suspension wind turbine gearboxes. A three dimensional multibody dynamic model is established, including gravity, bending moments, fluctuating mesh stiffness, nonlinear tooth contact, and bearing clearance. A flexible main shaft, planetary carrier, housing, and gear shafts are modeled using reduced degrees-of-freedom through modal compensation. This drivetrain model is validated against the experimental data of Gearbox Reliability Collaborative for gearbox internal loads. Planet load sharing is a combined effect of gravity, bending moment, bearing clearance, and input torque. Influences of each of these parameters and their combined effects on the resulting planetmore » load sharing are investigated. Bending moments and gravity induce fundamental excitations in the rotating carrier frame, which can increase gearbox internal loads and disturb load sharing. Clearance in carrier bearings reduces the bearing load carrying capacity and thus the bending moment from the rotor can be transmitted into gear meshes. With bearing clearance, the bending moment can cause tooth micropitting and can induce planet bearing fatigue, leading to reduced gearbox life. Planet bearings are susceptible to skidding at low input torque.« less
Yan, Y; Bell, K M; Hartman, R A; Hu, J; Wang, W; Kang, J D; Lee, J Y
2017-01-01
Various modifications to standard "rigid" anterior cervical plate designs (constrained plate) have been developed that allow for some degree of axial translation and/or rotation of the plate (semi-constrained plate)-theoretically promoting proper load sharing with the graft and improved fusion rates. However, previous studies about rigid and dynamic plates have not examined the influence of simulated muscle loading. The objective of this study was to compare rigid, translating, and rotating plates for single-level corpectomy procedures using a robot testing system with follower load. In-vitro biomechanical test. N = 15 fresh-frozen human (C3-7) cervical specimens were biomechanically tested. The follower load was applied to the specimens at the neutral position from 0 to 100 N. Specimens were randomized into a rigid plate group, a translating plate group and a rotating plate group and then tested in flexion, extension, lateral bending and axial rotation to a pure moment target of 2.0 Nm under 100N of follower load. Range of motion, load sharing, and adjacent level effects were analyzed using a repeated measures analysis of variance (ANOVA). No significant differences were observed between the translating plate and the rigid plate on load sharing at neutral position and C4-6 ROM, but the translating plate was able to maintain load through the graft at a desired level during flexion. The rotating plate shared less load than rigid and translating plates in the neutral position, but cannot maintain the graft load during flexion. This study demonstrated that, in the presence of simulated muscle loading (follower load), the translating plate demonstrated superior performance for load sharing compared to the rigid and rotating plates.
Federal Register 2010, 2011, 2012, 2013, 2014
2012-03-27
... Department of Justice Global Justice Information Sharing Initiative Federal Advisory Committee AGENCY: Office... meeting of the Department of Justice (DOJ) Global Justice Information Sharing Initiative (Global) Federal Advisory Committee (GAC) to discuss the Global Initiative, as described at www.it.ojp.gov/global . DATES...
Malaligned dynamic anterior cervical plate: a biomechanical analysis of effectiveness.
Lawrence, Brandon D; Patel, Alpesh A; Guss, Andrew; Ryan Spiker, W; Brodke, Darrel S
2014-12-01
Biomechanical evaluation. To evaluate the kinematic and load-sharing differences of dynamic anterior cervical plates when placed in-line at 0° and off-axis at 20°. The use of dynamic anterior cervical plating systems has recently gained popularity due to the theoretical benefit of improved load sharing with graft subsidence. Occasionally, due to anatomical restraints, the anterior cervical plate may be placed off-axis in the coronal plane. This may potentially decrease the dynamization capability of the plate, leading to less load sharing and potentially decreased fusion rates. The purpose of this study was to comprehensively evaluate the kinematic and load-sharing differences of a dynamic plate placed in-line versus off-axis in the coronal plane. Thirteen fresh-frozen human cadaveric cervical spines (C2-T1) were used. Nondestructive range-of-motion testing was performed with a pneumatically controlled spine simulator in flexion/extension, lateral bending, and axial rotation using the OptoTrak motion measurement system. A C5 corpectomy was performed, and a custom interbody spacer with an integrated load cell collected load-sharing data under axial compression at varying loads. A dynamic anterior cervical plate was placed in-line at 0° and then off-axis at 20°. Testing conditions ensued using a full-length spacer, followed by simulated subsidence by removing 10% of the height of the original spacer. There were no kinematic differences noted in the in-line model versus the off-axis model. After simulated subsidence, the small decreases in stiffness and increases in motion were similar whether the plate was placed in-line or off-axis in all 3 planes of motion. There were also no significant differences in the load-sharing characteristics of the in-line plate versus the off-axis plate in either the full-length model or the subsided interbody model. This study suggests that off-axis dynamic plate positioning does not significantly impact construct kinematics or graft load sharing. As such, we do not recommend removal or repositioning of an off-axis placed dynamic plate because the kinematic and load-sharing biomechanical properties are similar. N/A.
Load-sharing through elastic micro-motion accelerates bone formation and interbody fusion.
Ledet, Eric H; Sanders, Glenn P; DiRisio, Darryl J; Glennon, Joseph C
2018-02-13
Achieving a successful spinal fusion requires the proper biological and biomechanical environment. Optimizing load-sharing in the interbody space can enhance bone formation. For anterior cervical discectomy and fusion (ACDF), loading and motion are largely dictated by the stiffness of the plate, which can facilitate a balance between stability and load-sharing. The advantages of load-sharing may be substantial for patients with comorbidities and in multilevel procedures where pseudarthrosis rates are significant. We aimed to evaluate the efficacy of a novel elastically deformable, continuously load-sharing anterior cervical spinal plate for promotion of bone formation and interbody fusion relative to a translationally dynamic plate. An in vivo animal model was used to evaluate the effects of an elastically deformable spinal plate on bone formation and spine fusion. Fourteen goats underwent an ACDF and received either a translationally dynamic or elastically deformable plate. Animals were followed up until 18 weeks and were evaluated by plain x-ray, computed tomography scan, and undecalcified histology to evaluate the rate and quality of bone formation and interbody fusion. Animals treated with the elastically deformable plate demonstrated statistically significantly superior early bone formation relative to the translationally dynamic plate. Trends in the data from 8 to 18 weeks postoperatively suggest that the elastically deformable implant enhanced bony bridging and fusion, but these enhancements were not statistically significant. Load-sharing through elastic micro-motion accelerates bone formation in the challenging goat ACDF model. The elastically deformable implant used in this study may promote early bony bridging and increased rates of fusion, but future studies will be necessary to comprehensively characterize the advantages of load-sharing through micro-motion. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.
Planetary Load Sharing in Three-Point Mounted Wind Turbine Gearboxes: A Design and Test Comparison
DOE Office of Scientific and Technical Information (OSTI.GOV)
Keller, Jonathan; Guo, Yi; Zhang, Zhiwei
This work compares the planetary load-sharing characteristics of wind turbine gearboxes supported by cylindrical roller bearings (CRBs) and preloaded tapered roller bearings (TRBs) when subjected to rotor moments. Planetary bearing loads were measured in field-representative dynamometer tests and compared to loads predicted by finite-element models. Preloaded TRBs significantly improved load sharing. In pure torque conditions, the upwind planet bearing load in the gearbox with preloaded TRBs was only 14% more than the assumed load compared to 47% more for the gearbox with CRBs. Consequently, the predicted fatigue life of the complete set of planetary bearings for the gearbox with preloadedmore » TRBs is 3.5 times greater than that of the gearbox with CRBs.« less
Dataworks for GNSS: Software for Supporting Data Sharing and Federation of Geodetic Networks
NASA Astrophysics Data System (ADS)
Boler, F. M.; Meertens, C. M.; Miller, M. M.; Wier, S.; Rost, M.; Matykiewicz, J.
2015-12-01
Continuously-operating Global Navigation Satellite System (GNSS) networks are increasingly being installed globally for a wide variety of science and societal applications. GNSS enables Earth science research in areas including tectonic plate interactions, crustal deformation in response to loading by tectonics, magmatism, water and ice, and the dynamics of water - and thereby energy transfer - in the atmosphere at regional scale. The many individual scientists and organizations that set up GNSS stations globally are often open to sharing data, but lack the resources or expertise to deploy systems and software to manage and curate data and metadata and provide user tools that would support data sharing. UNAVCO previously gained experience in facilitating data sharing through the NASA-supported development of the Geodesy Seamless Archive Centers (GSAC) open source software. GSAC provides web interfaces and simple web services for data and metadata discovery and access, supports federation of multiple data centers, and simplifies transfer of data and metadata to long-term archives. The NSF supported the dissemination of GSAC to multiple European data centers forming the European Plate Observing System. To expand upon GSAC to provide end-to-end, instrument-to-distribution capability, UNAVCO developed Dataworks for GNSS with NSF funding to the COCONet project, and deployed this software on systems that are now operating as Regional GNSS Data Centers as part of the NSF-funded TLALOCNet and COCONet projects. Dataworks consists of software modules written in Python and Java for data acquisition, management and sharing. There are modules for GNSS receiver control and data download, a database schema for metadata, tools for metadata handling, ingest software to manage file metadata, data file management scripts, GSAC, scripts for mirroring station data and metadata from partner GSACs, and extensive software and operator documentation. UNAVCO plans to provide a cloud VM image of Dataworks that would allow standing up a Dataworks-enabled GNSS data center without requiring upfront investment in server hardware. By enabling data creators to organize their data and metadata for sharing, Dataworks helps scientists expand their data curation awareness and responsibility, and enhances data access for all.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Arafat, Humayun; Dinan, James; Krishnamoorthy, Sriram
Task parallelism is an attractive approach to automatically load balance the computation in a parallel system and adapt to dynamism exhibited by parallel systems. Exploiting task parallelism through work stealing has been extensively studied in shared and distributed-memory contexts. In this paper, we study the design of a system that uses work stealing for dynamic load balancing of task-parallel programs executed on hybrid distributed-memory CPU-graphics processing unit (GPU) systems in a global-address space framework. We take into account the unique nature of the accelerator model employed by GPUs, the significant performance difference between GPU and CPU execution as a functionmore » of problem size, and the distinct CPU and GPU memory domains. We consider various alternatives in designing a distributed work stealing algorithm for CPU-GPU systems, while taking into account the impact of task distribution and data movement overheads. These strategies are evaluated using microbenchmarks that capture various execution configurations as well as the state-of-the-art CCSD(T) application module from the computational chemistry domain.« less
Work stealing for GPU-accelerated parallel programs in a global address space framework
DOE Office of Scientific and Technical Information (OSTI.GOV)
Arafat, Humayun; Dinan, James; Krishnamoorthy, Sriram
Task parallelism is an attractive approach to automatically load balance the computation in a parallel system and adapt to dynamism exhibited by parallel systems. Exploiting task parallelism through work stealing has been extensively studied in shared and distributed-memory contexts. In this paper, we study the design of a system that uses work stealing for dynamic load balancing of task-parallel programs executed on hybrid distributed-memory CPU-graphics processing unit (GPU) systems in a global-address space framework. We take into account the unique nature of the accelerator model employed by GPUs, the significant performance difference between GPU and CPU execution as a functionmore » of problem size, and the distinct CPU and GPU memory domains. We consider various alternatives in designing a distributed work stealing algorithm for CPU-GPU systems, while taking into account the impact of task distribution and data movement overheads. These strategies are evaluated using microbenchmarks that capture various execution configurations as well as the state-of-the-art CCSD(T) application module from the computational chemistry domain« less
Li, Longbiao
2016-01-01
In this paper, the fatigue life of fiber-reinforced ceramic-matrix composites (CMCs) with different fiber preforms, i.e., unidirectional, cross-ply, 2D (two dimensional), 2.5D and 3D CMCs at room and elevated temperatures in air and oxidative environments, has been predicted using the micromechanics approach. An effective coefficient of the fiber volume fraction along the loading direction (ECFL) was introduced to describe the fiber architecture of preforms. The statistical matrix multicracking model and fracture mechanics interface debonding criterion were used to determine the matrix crack spacing and interface debonded length. Under cyclic fatigue loading, the fiber broken fraction was determined by combining the interface wear model and fiber statistical failure model at room temperature, and interface/fiber oxidation model, interface wear model and fiber statistical failure model at elevated temperatures, based on the assumption that the fiber strength is subjected to two-parameter Weibull distribution and the load carried by broken and intact fibers satisfies the Global Load Sharing (GLS) criterion. When the broken fiber fraction approaches the critical value, the composites fatigue fracture. PMID:28773332
Patellar fixation protected with a load-sharing cable: a mechanical and clinical study.
Perry, C R; McCarthy, J A; Kain, C C; Pearson, R L
1988-01-01
The stability of patellar fracture fixation protected with a load-sharing cable was studied in cadavers. A transverse patellar osteotomy was produced and stabilized with standard patellar fixation with or without a figure-of-eight cable that extends from the proximal pole of the patella to the tibial tubercle. Standard fixation techniques (interfragmentary cancellous screws or modified tension-band wiring) alone failed after significantly fewer cycles of flexion and extension than did the same fixation when supplemented with a load-sharing cable. In the clinical evaluation of the load-sharing cable, 14 consecutive patients with displaced patellar fractures were treated. No immobilization was used and the patients were started on passive and active range of motion and weight-bearing ambulation in the early postoperative period. Thirteen fractures healed uneventfully. The increased stability of patellar fracture fixation protected with a load-sharing cable offers three advantages: (a) adjunctive casting is unnecessary, (b) comminuted fractures can be "pieced" together anatomically with less concern for loss of fixation, and (c) early postoperative passive and active range of motion can be achieved.
Self-organized dynamics in local load-sharing fiber bundle models.
Biswas, Soumyajyoti; Chakrabarti, Bikas K
2013-10-01
We study the dynamics of a local load-sharing fiber bundle model in two dimensions under an external load (which increases with time at a fixed slow rate) applied at a single point. Due to the local load-sharing nature, the redistributed load remains localized along the boundary of the broken patch. The system then goes to a self-organized state with a stationary average value of load per fiber along the (increasing) boundary of the broken patch (damaged region) and a scale-free distribution of avalanche sizes and other related quantities are observed. In particular, when the load redistribution is only among nearest surviving fiber(s), the numerical estimates of the exponent values are comparable with those of the Manna model. When the load redistribution is uniform along the patch boundary, the model shows a simple mean-field limit of this self-organizing critical behavior, for which we give analytical estimates of the saturation load per fiber values and avalanche size distribution exponent. These are in good agreement with numerical simulation results.
Saifuddin, Mustafa; Jha, Shalene
2014-04-01
Given that many pollinators have exhibited dramatic declines related to habitat destruction, an improved understanding of pollinator resource collection across human-altered landscapes is essential to conservation efforts. Despite the importance of bumble bees (Bombus spp.) as global pollinators, little is known regarding how pollen collection patterns vary between individuals, colonies, and landscapes. In this study, Vosnesensky bumble bees (Bombus vosnesenskii Radoszkowski) were collected from a range of human-altered and natural landscapes in northern California. Extensive vegetation surveys and Geographic Information System (GIS)-based habitat classifications were conducted at each site, bees were genotyped to identify colony mates, and pollen loads were examined to identify visited plants. In contrast to predictions based on strong competitive interactions, pollen load composition was significantly more similar for bees captured in a shared study region compared with bees throughout the research area but was not significantly more similar for colony mates. Preference analyses revealed that pollen loads were not composed of the most abundant plant species per study region. The majority of ranked pollen preference lists were significantly correlated for pairwise comparisons of colony mates and individuals within a study region, whereas the majority of pairwise comparisons of ranked pollen preference lists between individuals located at separate study regions were uncorrelated. Results suggest that pollen load composition and foraging preferences are similar for bees throughout a shared landscape regardless of colony membership. The importance of native plant species in pollen collection is illustrated through preference analyses, and we suggest prioritization of specific rare native plant species for enhanced bumble bee pollen collection.
Attention and Visuospatial Working Memory Share the Same Processing Resources
Feng, Jing; Pratt, Jay; Spence, Ian
2012-01-01
Attention and visuospatial working memory (VWM) share very similar characteristics; both have the same upper bound of about four items in capacity and they recruit overlapping brain regions. We examined whether both attention and VWM share the same processing resources using a novel dual-task costs approach based on a load-varying dual-task technique. With sufficiently large loads on attention and VWM, considerable interference between the two processes was observed. A further load increase on either process produced reciprocal increases in interference on both processes, indicating that attention and VWM share common resources. More critically, comparison among four experiments on the reciprocal interference effects, as measured by the dual-task costs, demonstrates no significant contribution from additional processing other than the shared processes. These results support the notion that attention and VWM share the same processing resources. PMID:22529826
NASA Technical Reports Server (NTRS)
Sullivan, Roy M.
2016-01-01
The stress rupture strength of silicon carbide fiber-reinforced silicon carbide composites with a boron nitride fiber coating decreases with time within the intermediate temperature range of 700 to 950 degree Celsius. Various theories have been proposed to explain the cause of the time-dependent stress rupture strength. The objective of this paper is to investigate the relative significance of the various theories for the time-dependent strength of silicon carbide fiber-reinforced silicon carbide composites. This is achieved through the development of a numerically based progressive failure analysis routine and through the application of the routine to simulate the composite stress rupture tests. The progressive failure routine is a time-marching routine with an iterative loop between a probability of fiber survival equation and a force equilibrium equation within each time step. Failure of the composite is assumed to initiate near a matrix crack and the progression of fiber failures occurs by global load sharing. The probability of survival equation is derived from consideration of the strength of ceramic fibers with randomly occurring and slow growing flaws as well as the mechanical interaction between the fibers and matrix near a matrix crack. The force equilibrium equation follows from the global load sharing presumption. The results of progressive failure analyses of the composite tests suggest that the relationship between time and stress-rupture strength is attributed almost entirely to the slow flaw growth within the fibers. Although other mechanisms may be present, they appear to have only a minor influence on the observed time-dependent behavior.
Federal Register 2010, 2011, 2012, 2013, 2014
2013-03-20
... DEPARTMENT OF JUSTICE Office of Justice Programs [OJP (BJA) Docket No. 1616] Meeting of the Global Justice Information Sharing Initiative Federal Advisory Committee AGENCY: Office of Justice Programs (OJP... Information Sharing Initiative (Global) Federal Advisory Committee (GAC) to discuss the Global Initiative, as...
Expert Systems on Multiprocessor Architectures. Volume 3. Technical Reports
1991-06-01
choice of load balancing vs. load sharing 1141. While load balancing strives to keep all sites equally loaded, load sharing merely tries to prevent ...unnecessary idleness. Loo. balancing is appropriate to object- oriented real- time systems because * real-time systems ne ,l to prevent long waits for...oetavir ConClass siy51cr Iz a n ubjeU rephitation ’-enare ir order wo prevent a partic=Lar abiec:;ram heing (ntrlu ~lel Ar iic]en:f etautaan ire chanw
What Do the Various Principles of Justice Mean Within the Concept of Benefit Sharing?
Dauda, Bege; Denier, Yvonne; Dierickx, Kris
2016-06-01
The concept of benefit sharing pertains to the act of giving something in return to the participants, communities, and the country that have participated in global health research or bioprospecting activities. One of the key concerns of benefit sharing is the ethical justifications or reasons to support the practice of the concept in global health research and bioprospecting. This article evaluates one of such ethical justifications and its meaning to benefit sharing, namely justice. We conducted a systematic review to map the various principles of justice that are linked to benefit sharing and analysed their meaning to the concept of benefit sharing. Five principles of justice (commutative, distributive, global, procedural, and compensatory) have been shown to be relevant in the nuances of benefit sharing in both global health research and bioprospecting. The review findings indicate that each of these principles of justice provides a different perspective for a different benefit sharing rationale. For example, commutative justice provides a benefit sharing rationale that is focused on fair exchange of benefits between research sponsors and communities. Distributive justice produces a benefit sharing rationale that is focused on improving the health needs of the vulnerable research communities. We have suggested that a good benefit sharing framework particularly in global health research would be more beneficial if it combines all the principles of justice in its formulation. Nonetheless, there is a need for empirical studies to examine the various principles of justice and their nuances in benefit sharing among stakeholders in global health research.
Naserkhaki, Sadegh; Jaremko, Jacob L; El-Rich, Marwan
2016-09-06
There is a large, at times contradictory, body of research relating spinal curvature to Low Back Pain (LBP). Mechanical load is considered as important factor in LBP etiology. Geometry of the spinal structures and sagittal curvature of the lumbar spine govern its mechanical behavior. Thus, understanding how inter-individual geometry particularly sagittal curvature variation affects the spinal load-sharing becomes of high importance in LBP assessment. This study calculated and compared kinematics and load-sharing in three ligamentous lumbosacral spines: one hypo-lordotic (Hypo-L) with low lordosis, one normal-lordotic (Norm-L) with normal lordosis, and one hyper-lordotic (Hyper-L) with high lordosis in flexed and extended postures using 3D nonlinear Finite Element (FE) modeling. These postures were simulated by applying Follower Load (FL) combined with flexion or extension moment. The Hypo-L spine demonstrated stiffer behavior in flexion but more flexible response to extension compared to the Norm-L spine. The excessive lordosis stiffened response of the Hyper-L spine to extension but did not affect its resistance to flexion compared to the Norm-L spine. Despite the different resisting actions of the posterior ligaments to flexion moment, the increase of disc compression was similar in all the spines leading to similar load-sharing. However, resistance of the facet joints to extension was more important in the Norm- and Hyper-L spines which reduced the disc compression. The spinal curvature strongly influenced the magnitude and location of load on the spinal components and also altered the kinematics and load-sharing particularly in extension. Consideration of the subject-specific geometry and sagittal curvature should be an integral part of mechanical analysis of the lumbar spine. Copyright © 2016 Elsevier Ltd. All rights reserved.
Global health governance as shared health governance.
Ruger, Jennifer Prah
2012-07-01
With the exception of key 'proven successes' in global health, the current regime of global health governance can be understood as transnational and national actors pursuing their own interests under a rational actor model of international cooperation, which fails to provide sufficient justification for an obligation to assist in meeting the health needs of others. An ethical commitment to providing all with the ability to be healthy is required. This article develops select components of an alternative model of shared health governance (SHG), which aims to provide a 'road map,' 'focal points' and 'the glue' among various global health actors to better effectuate cooperation on universal ethical principles for an alternative global health equilibrium. Key features of SHG include public moral norms as shared authoritative standards; ethical commitments, shared goals and role allocation; shared sovereignty and constitutional commitments; legitimacy and accountability; country-level attention to international health relations. A framework of social agreement based on 'overlapping consensus' is contrasted against one based on self-interested political bargaining. A global health constitution delineating duties and obligations of global health actors and a global institute of health and medicine for holding actors responsible are proposed. Indicators for empirical assessment of select SHG principles are described. Global health actors, including states, must work together to correct and avert global health injustices through a framework of SHG based on shared ethical commitments.
Effect of perceptual load on conceptual processing: an extension of Vermeulen's theory.
Xie, Jiushu; Wang, Ruiming; Sun, Xun; Chang, Song
2013-10-01
The effect of color and shape load on conceptual processing was studied. Perceptual load effects have been found in visual and auditory conceptual processing, supporting the theory of embodied cognition. However, whether different types of visual concepts, such as color and shape, share the same perceptual load effects is unknown. In the current experiment, 32 participants were administered simultaneous perceptual and conceptual tasks to assess the relation between perceptual load and conceptual processing. Keeping color load in mind obstructed color conceptual processing. Hence, perceptual processing and conceptual load shared the same resources, suggesting embodied cognition. Color conceptual processing was not affected by shape pictures, indicating that different types of properties within vision were separate.
Rahimzadeh, Vasiliki; Dyke, Stephanie O M; Knoppers, Bartha M
2016-06-01
The Global Alliance for Genomics and Health is marshaling expertise in biomedical research and data sharing policy to propel bench-to-bedside translation of genomics in parallel with many of the BioSHaRE-EU initiatives described at length in this Issue. Worldwide representation of institutions, funders, researchers, and patient advocacy groups at the Global Alliance is testament to a shared ideal that sees maximizing the public good as a chief priority of genomic innovation in health. The Global Alliance has made a critical stride in this regard with the development of its Framework for Responsible Sharing of Genomic and Health-related Data.(1) This article first discusses the human rights pillars that underlie the Framework and mission of the Global Alliance. Second, it outlines the Global Alliance's use of data governance policies through a number of demonstration projects. Finally, the authors describe how the Global Alliance envisions international data sharing moving forward in the postgenomic era.
High-frequency ac power distribution in Space Station
NASA Technical Reports Server (NTRS)
Tsai, Fu-Sheng; Lee, Fred C. Y.
1990-01-01
A utility-type 20-kHz ac power distribution system for the Space Station, employing resonant power-conversion techniques, is presented. The system converts raw dc voltage from photovoltaic cells or three-phase LF ac voltage from a solar dynamic generator into a regulated 20-kHz ac voltage for distribution among various loads. The results of EASY5 computer simulations of the local and global performance show that the system has fast response and good transient behavior. The ac bus voltage is effectively regulated using the phase-control scheme, which is demonstrated with both line and load variations. The feasibility of paralleling the driver-module outputs is illustrated with the driver modules synchronized and sharing a common feedback loop. An HF sinusoidal ac voltage is generated in the three-phase ac input case, when the driver modules are phased 120 deg away from one another and their outputs are connected in series.
Distributed shared memory for roaming large volumes.
Castanié, Laurent; Mion, Christophe; Cavin, Xavier; Lévy, Bruno
2006-01-01
We present a cluster-based volume rendering system for roaming very large volumes. This system allows to move a gigabyte-sized probe inside a total volume of several tens or hundreds of gigabytes in real-time. While the size of the probe is limited by the total amount of texture memory on the cluster, the size of the total data set has no theoretical limit. The cluster is used as a distributed graphics processing unit that both aggregates graphics power and graphics memory. A hardware-accelerated volume renderer runs in parallel on the cluster nodes and the final image compositing is implemented using a pipelined sort-last rendering algorithm. Meanwhile, volume bricking and volume paging allow efficient data caching. On each rendering node, a distributed hierarchical cache system implements a global software-based distributed shared memory on the cluster. In case of a cache miss, this system first checks page residency on the other cluster nodes instead of directly accessing local disks. Using two Gigabit Ethernet network interfaces per node, we accelerate data fetching by a factor of 4 compared to directly accessing local disks. The system also implements asynchronous disk access and texture loading, which makes it possible to overlap data loading, volume slicing and rendering for optimal volume roaming.
Concurrent working memory load can facilitate selective attention: evidence for specialized load.
Park, Soojin; Kim, Min-Shik; Chun, Marvin M
2007-10-01
Load theory predicts that concurrent working memory load impairs selective attention and increases distractor interference (N. Lavie, A. Hirst, J. W. de Fockert, & E. Viding). Here, the authors present new evidence that the type of concurrent working memory load determines whether load impairs selective attention or not. Working memory load was paired with a same/different matching task that required focusing on targets while ignoring distractors. When working memory items shared the same limited-capacity processing mechanisms with targets in the matching task, distractor interference increased. However, when working memory items shared processing with distractors in the matching task, distractor interference decreased, facilitating target selection. A specialized load account is proposed to describe the dissociable effects of working memory load on selective processing depending on whether the load overlaps with targets or with distractors. (c) 2007 APA
Shared Leadership for a Green, Global, and Google World
ERIC Educational Resources Information Center
Duin, Ann Hill; Baer, Linda L.
2010-01-01
Higher education institutions must be resilient as they face vastly increased expectations for sustainable environments, global focus, and technological support. Speed of response to these expectations ultimately depends on shared vision, shared agreement, and shared accountability. In this article, the authors challenge all those engaged with…
Programming distributed memory architectures using Kali
NASA Technical Reports Server (NTRS)
Mehrotra, Piyush; Vanrosendale, John
1990-01-01
Programming nonshared memory systems is more difficult than programming shared memory systems, in part because of the relatively low level of current programming environments for such machines. A new programming environment is presented, Kali, which provides a global name space and allows direct access to remote data values. In order to retain efficiency, Kali provides a system on annotations, allowing the user to control those aspects of the program critical to performance, such as data distribution and load balancing. The primitives and constructs provided by the language is described, and some of the issues raised in translating a Kali program for execution on distributed memory systems are also discussed.
Simulation of load-sharing in standalone distributed generation system
NASA Astrophysics Data System (ADS)
Ajewole, Titus O.; Craven, Robert P. M.; Kayode, Olakunle; Babalola, Olufisayo S.
2018-05-01
This paper presents a study on load-sharing among the component generating units of a multi-source electric microgrid that is operated as an autonomous ac supply-mode system. Emerging trend in power system development permits deployment of microgrids for standalone or stand-by applications, thereby requiring active- and reactive power sharing among the discrete generating units contained in hybrid-source microgrids. In this study, therefore, a laboratory-scale model of a microgrid energized with three renewable energy-based sources is employed as a simulation platform to investigate power sharing among the power-generating units. Each source is represented by a source emulator that captures the real operational characteristics of the mimicked generating unit and, with implementation of real-life weather data and load profiles on the model; the sharing of the load among the generating units is investigated. There is a proportionate generation of power by the three source emulators, with their frequencies perfectly synchronized at the point of common coupling as a result of balance flow of power among them. This hybrid topology of renewable energy-based microgrid could therefore be seamlessly adapted into national energy mix by the indigenous electric utility providers in Nigeria.
Exploring Manycore Multinode Systems for Irregular Applications with FPGA Prototyping
DOE Office of Scientific and Technical Information (OSTI.GOV)
Ceriani, Marco; Palermo, Gianluca; Secchi, Simone
We present a prototype of a multi-core architecture implemented on FPGA, designed to enable efficient execution of irregular applications on distributed shared memory machines, while maintaining high performance on regular workloads. The architecture is composed of off-the-shelf soft-core cores, local interconnection and memory interface, integrated with custom components that optimize it for irregular applications. It relies on three key elements: a global address space, multithreading, and fine-grained synchronization. Global addresses are scrambled to reduce the formation of network hot-spots, while the latency of the transactions is covered by integrating an hardware scheduler within the custom load/store buffers to take advantagemore » from the availability of multiple executions threads, increasing the efficiency in a transparent way to the application. We evaluated a dual node system irregular kernels showing scalability in the number of cores and threads.« less
Designing for Global Data Sharing, Designing for Educational Transformation
ERIC Educational Resources Information Center
Adams, Robin S.; Radcliffe, David; Fosmire, Michael
2016-01-01
This paper provides an example of a global data sharing project with an educational transformation agenda. This agenda shaped both the design of the shared dataset and the experience of sharing the common dataset to support multiple perspective inquiry and enable integrative and critically reflexive research-to-practice dialogue. The shared…
Bullerjahn, George S; McKay, Robert M; Davis, Timothy W; Baker, David B; Boyer, Gregory L; D'Anglada, Lesley V; Doucette, Gregory J; Ho, Jeff C; Irwin, Elena G; Kling, Catherine L; Kudela, Raphael M; Kurmayer, Rainer; Michalak, Anna M; Ortiz, Joseph D; Otten, Timothy G; Paerl, Hans W; Qin, Boqiang; Sohngen, Brent L; Stumpf, Richard P; Visser, Petra M; Wilhelm, Steven W
2016-04-01
In early August 2014, the municipality of Toledo, OH (USA) issued a 'do not drink' advisory on their water supply directly affecting over 400,000 residential customers and hundreds of businesses (Wilson, 2014). This order was attributable to levels of microcystin, a potent liver toxin, which rose to 2.5μgL -1 in finished drinking water. The Toledo crisis afforded an opportunity to bring together scientists from around the world to share ideas regarding factors that contribute to bloom formation and toxigenicity, bloom and toxin detection as well as prevention and remediation of bloom events. These discussions took place at an NSF- and NOAA-sponsored workshop at Bowling Green State University on April 13 and 14, 2015. In all, more than 100 attendees from six countries and 15 US states gathered together to share their perspectives. The purpose of this review is to present the consensus summary of these issues that emerged from discussions at the Workshop. As additional reports in this special issue provide detailed reviews on many major CHAB species, this paper focuses on the general themes common to all blooms, such as bloom detection, modeling, nutrient loading, and strategies to reduce nutrients. Copyright © 2016 Elsevier B.V. All rights reserved.
Bullerjahn, George S.; McKay, Robert M.; Davis, Timothy W.; Baker, David B.; Boyer, Gregory L.; D’Anglada, Lesley V.; Doucette, Gregory J.; Ho, Jeff C.; Irwin, Elena G.; Kling, Catherine L.; Kudela, Raphael M.; Kurmayer, Rainer; Michalak, Anna M.; Ortiz, Joseph D.; Otten, Timothy G.; Paerl, Hans W.; Qin, Boqiang; Sohngen, Brent L.; Stumpf, Richard P.; Visser, Petra M.; Wilhelm, Steven W.
2016-01-01
In early August 2014, the municipality of Toledo, OH (USA) issued a ‘do not drink’ advisory on their water supply directly affecting over 400,000 residential customers and hundreds of businesses (Wilson, 2014). This order was attributable to levels of microcystin, a potent liver toxin, which rose to 2.5 μg L-1 in finished drinking water. The Toledo crisis afforded an opportunity to bring together scientists from around the world to share ideas regarding factors that contribute to bloom formation and toxigenicity, bloom and toxin detection as well as prevention and remediation of bloom events. These discussions took place at an NSF- and NOAA-sponsored workshop at Bowling Green State University on April 13 and 14, 2015. In all, more than 100 attendees from six countries and 15 US states gathered together to share their perspectives. The purpose of this review is to present the consensus summary of these issues that emerged from discussions at the Workshop. As additional reports in this special issue provide detailed reviews on many major CHAB species, this paper focuses on the general themes common to all blooms, such as bloom detection, modeling, nutrient loading, and strategies to reduce nutrients. PMID:28073479
Global baseline data on phosphorus pollution of large lakes
NASA Astrophysics Data System (ADS)
Fink, Gabriel; Flörke, Martina; Alcamo, Joseph
2016-04-01
Lakes are exposed to harmful eutrophication which is the most concerning water quality issue on global scale. Eutrophication is caused by phosphorous pollution in most lakes. Hence, global consistent base line data on phosphorus loadings are needed to assess future sustainable development. We used the modeling framework WaterGAP3 to calculate present total phosphorus loadings to the world's largest lakes. Estimates of modeled total phosphorus (TP) loadings as well as the contributions of different sectors were successfully validated against measured data. Based on these findings, annual total phosphorus loadings to lakes were calculated for diffuse and point sources according to the different sectors domestic, manufacturing, urban surface runoff, agriculture and background for the time period 1990 to 2010. Our results show high phosphorus loadings into lakes in southern latitudes. On global average, industrial fertilizer is the main anthropogenic source while background loadings are low in comparison. Nevertheless, both features indicate a high potential to reduce the exposure to eutrophication in lakes which are faced with high phosphor inputs. The global average of TP loadings was 7% higher in the time period 2005-2010 than in the period 1990-1995. The global average in 2005-2010 results from an increase in TP loadings of 79% in South America, which was dampened by a decrease in Europe, North America, and Asia. Chinese lakes were exposed to massive increasing phosphorus loadings, too. Both increasing and decreasing trends are caused primarily by changing industrial fertilizer application rates. In conclusion, this study provides a consistent and model based synopsis of global trends and sources of phosphorus loadings to large lakes. The estimates of phosphorus pollution of lakes present a basis for assessing and managing the global eutrophication problem.
Analysis of dynamic behavior of multiple-stage planetary gear train used in wind driven generator.
Wang, Jungang; Wang, Yong; Huo, Zhipu
2014-01-01
A dynamic model of multiple-stage planetary gear train composed of a two-stage planetary gear train and a one-stage parallel axis gear is proposed to be used in wind driven generator to analyze the influence of revolution speed and mesh error on dynamic load sharing characteristic based on the lumped parameter theory. Dynamic equation of the model is solved using numerical method to analyze the uniform load distribution of the system. It is shown that the load sharing property of the system is significantly affected by mesh error and rotational speed; load sharing coefficient and change rate of internal and external meshing of the system are of obvious difference from each other. The study provides useful theoretical guideline for the design of the multiple-stage planetary gear train of wind driven generator.
Analysis of Dynamic Behavior of Multiple-Stage Planetary Gear Train Used in Wind Driven Generator
Wang, Jungang; Wang, Yong; Huo, Zhipu
2014-01-01
A dynamic model of multiple-stage planetary gear train composed of a two-stage planetary gear train and a one-stage parallel axis gear is proposed to be used in wind driven generator to analyze the influence of revolution speed and mesh error on dynamic load sharing characteristic based on the lumped parameter theory. Dynamic equation of the model is solved using numerical method to analyze the uniform load distribution of the system. It is shown that the load sharing property of the system is significantly affected by mesh error and rotational speed; load sharing coefficient and change rate of internal and external meshing of the system are of obvious difference from each other. The study provides useful theoretical guideline for the design of the multiple-stage planetary gear train of wind driven generator. PMID:24511295
Benefit Sharing in a Global Context: Working Towards Solutions for Implementation.
Hurst, Daniel J
2017-08-01
Due to the state of globalized clinical research, questions have been raised as to what, if any, benefits those who contribute to research should receive. One model for compensating research participants is "benefit sharing," and the basic premise is that, as a matter of justice, those who contribute to scientific research should share in its benefits. While incorporated into several international documents for over two decades, benefit sharing has only been sparsely implemented. This analysis begins by addressing the concept of benefit sharing, its historical development, and how it has been applied in the context of virus sharing for influenza research. The second portion of this analysis presents recommendations for ensuring benefit sharing. These recommendations are threefold: 1) an emphasis on social pressure, 2) the revision of international documents as means to ensure benefit sharing, and 3) greater collaboration between sponsor IRB and host country IRB. Because clinical research is a globalized industry, a global model will be proposed in the second that focuses on collaboration between the sponsor and host country. This collaboration is vital in order to ensure that proper forms of benefit sharing are accomplished as a matter of justice. © 2016 John Wiley & Sons Ltd.
Federal Register 2010, 2011, 2012, 2013, 2014
2012-06-19
... Change Relating to the Accuvest Global Long Short ETF (Formerly the Mars Hill Global Relative Value ETF...) applicable to, the Accuvest Global Long Short ETF (``Fund'') (formerly known as the Mars Hill Global Relative... the Exchange of shares (``Shares'') of the Mars Hill Global Relative Value ETF, a series of Advisor...
NASA Astrophysics Data System (ADS)
Longbiao, Li
2017-08-01
In this paper, the synergistic effects of temperature, oxidation and multicracking modes on damage evolution and life prediction in 2D woven ceramic-matrix composites (CMCs) have been investigated. The damage parameter of fatigue hysteresis dissipated energy and the interface shear stress were used to monitor the damage evolution inside of CMCs. Under cyclic fatigue loading, the fibers broken fraction was determined by combining the interface/fiber oxidation model, interface wear model and fibers statistical failure model at elevated temperature, based on the assumption that the fiber strength is subjected to two-parameter Weibull distribution and the load carried by broken and intact fibers satisfy the Global Load Sharing (GLS) criterion. When the broken fibers fraction approaches to the critical value, the composite fatigue fractures. The evolution of fatigue hysteresis dissipated energy, the interface shear stress and broken fibers fraction versus cycle number, and the fatigue life S-N curves of SiC/SiC at 1000, 1200 and 1300 °C in air and steam condition have been predicted. The synergistic effects of temperature, oxidation, fatigue peak stress, and multicracking modes on the evolution of interface shear stress and fatigue hysteresis dissipated energy versus cycle numbers curves have been analyzed.
Controllable load sharing for soft adhesive interfaces on three-dimensional surfaces.
Song, Sukho; Drotlef, Dirk-Michael; Majidi, Carmel; Sitti, Metin
2017-05-30
For adhering to three-dimensional (3D) surfaces or objects, current adhesion systems are limited by a fundamental trade-off between 3D surface conformability and high adhesion strength. This limitation arises from the need for a soft, mechanically compliant interface, which enables conformability to nonflat and irregularly shaped surfaces but significantly reduces the interfacial fracture strength. In this work, we overcome this trade-off with an adhesion-based soft-gripping system that exhibits enhanced fracture strength without sacrificing conformability to nonplanar 3D surfaces. Composed of a gecko-inspired elastomeric microfibrillar adhesive membrane supported by a pressure-controlled deformable gripper body, the proposed soft-gripping system controls the bonding strength by changing its internal pressure and exploiting the mechanics of interfacial equal load sharing. The soft adhesion system can use up to ∼26% of the maximum adhesion of the fibrillar membrane, which is 14× higher than the adhering membrane without load sharing. Our proposed load-sharing method suggests a paradigm for soft adhesion-based gripping and transfer-printing systems that achieves area scaling similar to that of a natural gecko footpad.
Controllable load sharing for soft adhesive interfaces on three-dimensional surfaces
NASA Astrophysics Data System (ADS)
Song, Sukho; Drotlef, Dirk-Michael; Majidi, Carmel; Sitti, Metin
2017-05-01
For adhering to three-dimensional (3D) surfaces or objects, current adhesion systems are limited by a fundamental trade-off between 3D surface conformability and high adhesion strength. This limitation arises from the need for a soft, mechanically compliant interface, which enables conformability to nonflat and irregularly shaped surfaces but significantly reduces the interfacial fracture strength. In this work, we overcome this trade-off with an adhesion-based soft-gripping system that exhibits enhanced fracture strength without sacrificing conformability to nonplanar 3D surfaces. Composed of a gecko-inspired elastomeric microfibrillar adhesive membrane supported by a pressure-controlled deformable gripper body, the proposed soft-gripping system controls the bonding strength by changing its internal pressure and exploiting the mechanics of interfacial equal load sharing. The soft adhesion system can use up to ˜26% of the maximum adhesion of the fibrillar membrane, which is 14× higher than the adhering membrane without load sharing. Our proposed load-sharing method suggests a paradigm for soft adhesion-based gripping and transfer-printing systems that achieves area scaling similar to that of a natural gecko footpad.
Controllable load sharing for soft adhesive interfaces on three-dimensional surfaces
Song, Sukho; Drotlef, Dirk-Michael; Majidi, Carmel; Sitti, Metin
2017-01-01
For adhering to three-dimensional (3D) surfaces or objects, current adhesion systems are limited by a fundamental trade-off between 3D surface conformability and high adhesion strength. This limitation arises from the need for a soft, mechanically compliant interface, which enables conformability to nonflat and irregularly shaped surfaces but significantly reduces the interfacial fracture strength. In this work, we overcome this trade-off with an adhesion-based soft-gripping system that exhibits enhanced fracture strength without sacrificing conformability to nonplanar 3D surfaces. Composed of a gecko-inspired elastomeric microfibrillar adhesive membrane supported by a pressure-controlled deformable gripper body, the proposed soft-gripping system controls the bonding strength by changing its internal pressure and exploiting the mechanics of interfacial equal load sharing. The soft adhesion system can use up to ∼26% of the maximum adhesion of the fibrillar membrane, which is 14× higher than the adhering membrane without load sharing. Our proposed load-sharing method suggests a paradigm for soft adhesion-based gripping and transfer-printing systems that achieves area scaling similar to that of a natural gecko footpad. PMID:28507143
Reliability demonstration test for load-sharing systems with exponential and Weibull components
Hu, Qingpei; Yu, Dan; Xie, Min
2017-01-01
Conducting a Reliability Demonstration Test (RDT) is a crucial step in production. Products are tested under certain schemes to demonstrate whether their reliability indices reach pre-specified thresholds. Test schemes for RDT have been studied in different situations, e.g., lifetime testing, degradation testing and accelerated testing. Systems designed with several structures are also investigated in many RDT plans. Despite the availability of a range of test plans for different systems, RDT planning for load-sharing systems hasn’t yet received the attention it deserves. In this paper, we propose a demonstration method for two specific types of load-sharing systems with components subject to two distributions: exponential and Weibull. Based on the assumptions and interpretations made in several previous works on such load-sharing systems, we set the mean time to failure (MTTF) of the total system as the demonstration target. We represent the MTTF as a summation of mean time between successive component failures. Next, we introduce generalized test statistics for both the underlying distributions. Finally, RDT plans for the two types of systems are established on the basis of these test statistics. PMID:29284030
Reliability demonstration test for load-sharing systems with exponential and Weibull components.
Xu, Jianyu; Hu, Qingpei; Yu, Dan; Xie, Min
2017-01-01
Conducting a Reliability Demonstration Test (RDT) is a crucial step in production. Products are tested under certain schemes to demonstrate whether their reliability indices reach pre-specified thresholds. Test schemes for RDT have been studied in different situations, e.g., lifetime testing, degradation testing and accelerated testing. Systems designed with several structures are also investigated in many RDT plans. Despite the availability of a range of test plans for different systems, RDT planning for load-sharing systems hasn't yet received the attention it deserves. In this paper, we propose a demonstration method for two specific types of load-sharing systems with components subject to two distributions: exponential and Weibull. Based on the assumptions and interpretations made in several previous works on such load-sharing systems, we set the mean time to failure (MTTF) of the total system as the demonstration target. We represent the MTTF as a summation of mean time between successive component failures. Next, we introduce generalized test statistics for both the underlying distributions. Finally, RDT plans for the two types of systems are established on the basis of these test statistics.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Guo, Yi; Keller, Jonathan; Zhang, Zhiwei
The planetary load sharing characteristics of wind turbine gearboxes supported by cylindrical roller bearings (CRBs) and preloaded tapered roller bearings (TRBs) when subjected to rotor moments are compared in this work. Planetary bearing loads were measured in field-representative dynamometer tests and compared to loads predicted by finite-element models. Load sharing was significantly improved with preloaded TRBs. In pure torque conditions, the upwind planet bearing loads in the gearbox with preloaded TRBs were a maximum of 1.14 compared to 1.47 in the gearbox with CRBs. Consequently, the predicted fatigue life of the complete set of planetary bearings for the gearbox withmore » preloaded TRBs is 3.5 times greater than that of the gearbox with CRBs.« less
[Effects of the verbal loading on laterality difference in visual field (author's transl)].
Kawai, M
1980-02-01
In connection with the Kinsbourne's attention-model, the relation between the level of hemisphere sharing of loading task and the visual-laterality difference was examined under verbal loading conditions. The subjects were 13 (8 male and 5 female) right-handed college students. The loading tasks in Exp. I were the "same-different" judgment of Japanese hiragana alphabets and of triliteral hiragana words, and "true-false" judgment of short statements. In Exp. II, a procedure to eliminate configurational matching of the letters was followed. The results of the two experiments suggest that the visual-laterality effect occurs only when the level of hemisphere sharing of the loading task exceeds a certain lower bound.
Elastomeric load sharing device
NASA Technical Reports Server (NTRS)
Isabelle, Charles J. (Inventor); Kish, Jules G. (Inventor); Stone, Robert A. (Inventor)
1992-01-01
An elastomeric load sharing device, interposed in combination between a driven gear and a central drive shaft to facilitate balanced torque distribution in split power transmission systems, includes a cylindrical elastomeric bearing and a plurality of elastomeric bearing pads. The elastomeric bearing and bearing pads comprise one or more layers, each layer including an elastomer having a metal backing strip secured thereto. The elastomeric bearing is configured to have a high radial stiffness and a low torsional stiffness and is operative to radially center the driven gear and to minimize torque transfer through the elastomeric bearing. The bearing pads are configured to have a low radial and torsional stiffness and a high axial stiffness and are operative to compressively transmit torque from the driven gear to the drive shaft. The elastomeric load sharing device has spring rates that compensate for mechanical deviations in the gear train assembly to provide balanced torque distribution between complementary load paths of split power transmission systems.
Experimental Study of Split-Path Transmission Load Sharing
NASA Technical Reports Server (NTRS)
Krantz, Timothy L.; Delgado, Irebert R.
1996-01-01
Split-path transmissions are promising, attractive alternatives to the common planetary transmissions for helicopters. The split-path design offers two parallel paths for transmitting torque from the engine to the rotor. Ideally, the transmitted torque is shared equally between the two load paths; however, because of manufacturing tolerances, the design must be sized to allow for other than equal load sharing. To study the effect of tolerances, experiments were conducted using the NASA split-path test gearbox. Two gearboxes, nominally identical except for manufacturing tolerances, were tested. The clocking angle was considered to be a design parameter and used to adjust the load sharing of an otherwise fixed design. The torque carried in each path was measured for a matrix of input torques and clocking angles. The data were used to determine the optimal value and a tolerance for the clocking angles such that the most heavily loaded split path carried no greater than 53 percent of an input shaft torque of 367 N-m. The range of clocking angles satisfying this condition was -0.0012 +/- 0.0007 rad for box 1 and -0.0023 +/- 0.0009 rad for box 2. This study indicates that split-path gearboxes can be used successfully in rotorcraft and can be manufactured with existing technology.
NASA Astrophysics Data System (ADS)
Mekonnen, Mesfin M.; Hoekstra, Arjen Y.
2018-01-01
We estimate the global anthropogenic phosphorus (P) loads to freshwater and the associated grey water footprints (GWFs) for the period 2002-2010, at a spatial resolution of 5 × 5 arc min, and compare the GWF per river basin to runoff to assess the P-related water pollution level (WPL). The global anthropogenic P load to freshwater systems from both diffuse and point sources is estimated at 1.5 Tg/yr. More than half of this total load was in Asia, followed by Europe (19%) and Latin America and the Caribbean (13%). The domestic sector contributed 54% to the total, agriculture 38%, and industry 8%. In agriculture, cereals production had the largest contribution to the P load (31%), followed by fruits, vegetables, and oil crops, each contributing 15%. The global total GWF related to anthropogenic P loads is estimated to be 147 × 1012 m3/yr, with China contributing 30%, India 8%, USA 7%, and Spain and Brazil 6% each. The basins with WPL > 1 (where GWF exceeds the basin's assimilation capacity) together cover about 38% of the global land area, 37% of the global river discharge, and provide residence to about 90% of the global population.
Sharing Data in the Global Ocean Observing System (Invited)
NASA Astrophysics Data System (ADS)
Lindstrom, E. J.; McCurdy, A.; Young, J.; Fischer, A. S.
2010-12-01
We examine the evolution of data sharing in the field of physical oceanography to highlight the challenges now before us. Synoptic global observation of the ocean from space and in situ platforms has significantly matured over the last two decades. In the early 1990’s the community data sharing challenges facing the World Ocean Circulation Experiment (WOCE) largely focused on the behavior of individual scientists. Satellite data sharing depended on the policy of individual agencies. Global data sets were delivered with considerable delay and with enormous personal sacrifice. In the 2000’s the requirements for global data sets and sustained observations from the likes of the U.N. Framework Convention on Climate Change have led to data sharing and cooperation at a grander level. It is more effective and certainly more efficient. The Joint WMO/IOC Technical Commission on Oceanography and Marine Meteorology (JCOMM) provided the means to organize many aspects of data collection and data dissemination globally, for the common good. In response the Committee on Earth Observing Satellites organized Virtual Constellations to enable the assembly and sharing of like kinds of satellite data (e.g., sea surface topography, ocean vector winds, and ocean color). Individuals in physical oceanography have largely adapted to the new rigors of sharing data for the common good, and as a result of this revolution new science has been enabled. Primary obstacles to sharing have shifted from the individual level to the national level. As we enter into the 2010’s the demands for ocean data continue to evolve with an expanded requirement for more real-time reporting and broader disciplinary coverage, to answer key scientific and societal questions. We are also seeing the development of more numerous national contributions to the global observing system. The drivers for the establishment of global ocean observing systems are expanding beyond climate to include biological and biogeochemical issues (e.g. biodiversity and ecosystem services, fisheries collapse, and ocean acidification). This expanded suite of demands and drivers challenge us further to share data for the common good across specialties. This requires that more ocean scientific communities and national ocean observing programs move towards maturity in terms of global data collection capability, sharing capacity, and data management standards. In oceanography the time has arrived for a cultural shift toward more shared collective observing capabilities. Necessarily we must also rapidly move toward harmony in national data sharing policies for the ocean environment. Building capacity to share ocean observations has been an objective for decades and has resulted in an expanded understanding of technologies and management policies that foster data sharing and provenance tracking.
Researching the Habitus of Global Policy Actors in Education
ERIC Educational Resources Information Center
Lingard, Bob; Sellar, Sam; Baroutsis, Aspa
2015-01-01
This paper reprises the argument for the emergence of a global education policy field and then focuses on the shared habitus of global and national policy actors and technicians. It is argued that this shared habitus is constituted as a reflection of and a contribution to the creation of the global education policy field. Bourdieu's approach to…
Global Earth Response to Loading by Ocean Tide Models
NASA Technical Reports Server (NTRS)
Estes, R. H.; Strayer, J. M.
1979-01-01
Mathematical and programming techniques to numerically calculate Earth response to global semidiurnal and diurnal ocean tide models were developed. Global vertical crustal deformations were evaluated for M sub 2, S sub 2, N sub 2, K sub 2, K sub 1, O sub 1, and P sub 1 ocean tide loading, while horizontal deformations were evaluated for the M sub 2 tidal load. Tidal gravity calculations were performed for M sub 2 tidal loads, and strain tensor elements were evaluated for M sub 2 loads. The M sub 2 solution used for the ocean tide included the effects of self-gravitation and crustal loading.
NASA Astrophysics Data System (ADS)
Voss, Anja; Bärlund, Ilona; Punzet, Manuel; Williams, Richard; Teichert, Ellen; Malve, Olli; Voß, Frank
2010-05-01
Although catchment scale modelling of water and solute transport and transformations is a widely used technique to study pollution pathways and effects of natural changes, policies and mitigation measures there are only a few examples of global water quality modelling. This work will provide a description of the new continental-scale model of water quality WorldQual and the analysis of model simulations under changed climate and anthropogenic conditions with respect to changes in diffuse and point loading as well as surface water quality. BOD is used as an indicator of the level of organic pollution and its oxygen-depleting potential, and for the overall health of aquatic ecosystems. The first application of this new water quality model is to river systems of Europe. The model itself is being developed as part of the EU-funded SCENES Project which has the principal goal of developing new scenarios of the future of freshwater resources in Europe. The aim of the model is to determine chemical fluxes in different pathways combining analysis of water quantity with water quality. Simple equations, consistent with the availability of data on the continental scale, are used to simulate the response of in-stream BOD concentrations to diffuse and anthropogenic point loadings as well as flow dilution. Point sources are divided into manufacturing, domestic and urban loadings, whereas diffuse loadings come from scattered settlements, agricultural input (for instance livestock farming), and also from natural background sources. The model is tested against measured longitudinal gradients and time series data at specific river locations with different loading characteristics like the Thames that is driven by domestic loading and Ebro with relative high share of diffuse loading. With scenario studies the influence of climate and anthropogenic changes on European water resources shall be investigated with the following questions: 1. What percentage of river systems will have degraded water quality due to different driving forces? 2. How will climate change and changes in wastewater discharges affect water quality? For the analysis these scenario aspects are included: 1. climate with changed runoff (affecting diffuse pollution and loading from sealed areas), river discharge (causing dilution or concentration of point source pollution) and water temperature (affecting BOD degradation). 2. Point sources with changed population (affecting domestic pollution), connectivity to treatment plants (influencing domestic and manufacturing pollution as well as input from sealed areas and scattered settlements).
A Load-Sharing Rip-Stop Fixation Construct for Arthroscopic Rotator Cuff Repair
Denard, Patrick J.; Burkhart, Stephen S.
2012-01-01
Despite advancements in arthroscopic rotator cuff repair techniques, achieving tendon-to-bone healing can be difficult in the setting of poor-quality tendon. Moreover, medial tendon tears or tears with lateral tendon loss may preclude standard techniques. Rip-stop suture configurations have been shown to improve load to failure compared with simple or mattress stitch patterns and may be particularly valuable in these settings. The purpose of this report is to describe a technical modification of a rip-stop rotator cuff repair that combines the advantages of a rip-stop suture (by providing resistance to tissue cutout) and a double row of load-sharing suture anchors (minimizing the load per anchor and therefore the load per suture within each anchor). PMID:23766972
ERIC Educational Resources Information Center
Li, Rui; Liu, Min
2007-01-01
The purpose of this study is to examine the potential of using computer databases as cognitive tools to share learners' cognitive load and facilitate learning in a multimedia problem-based learning (PBL) environment designed for sixth graders. Two research questions were: (a) can the computer database tool share sixth-graders' cognitive load? and…
Shared wilderness, shared responsibility, shared vision: Protecting migratory wildlife
Will Meeks; Jimmy Fox; Nancy Roeper
2011-01-01
Wilderness plays a vital role in global and landscape-level conservation of wildlife. Millions of migratory birds and mammals rely on wilderness lands and waters during critical parts of their life. As large, ecologically intact landscapes, wilderness areas also play a vital role in addressing global climate change by increasing carbon sequestration, reducing...
Ahmed, Lubna; de Fockert, Jan W
2012-10-01
Selective attention to relevant targets has been shown to depend on the availability of working memory (WM). Under conditions of high WM load, processing of irrelevant distractors is enhanced. Here we showed that this detrimental effect of WM load on selective attention efficiency is reversed when the task requires global- rather than local-level processing. Participants were asked to attend to either the local or the global level of a hierarchical Navon stimulus while keeping either a low or a high load in WM. In line with previous findings, during attention to the local level, distractors at the global level produced more interference under high than under low WM load. By contrast, loading WM had the opposite effect of improving selective attention during attention to the global level. The findings demonstrate that the impact of WM load on selective attention is not invariant, but rather is dependent on the level of the to-be-attended information.
... medlineplus.gov/ency/article/003615.htm Acid loading test (pH) To use the sharing features on this page, please enable JavaScript. The acid loading test (pH) measures the ability of the kidneys to send ...
NASA Technical Reports Server (NTRS)
Sullivan, Roy M.
2015-01-01
The stress rupture strength of silicon carbide fiber-reinforced silicon carbide (SiCSiC) composites with a boron nitride (BN) fiber coating decreases with time within the intermediate temperature range of 700-950 C. Various theories have been proposed to explain the cause of the time dependent stress rupture strength. Some previous authors have suggested that the observed composite strength behavior is due to the inherent time dependent strength of the fibers, which is caused by the slow growth of flaws within the fibers. Flaw growth is supposedly enabled by oxidation of free carbon at the grain boundaries. The objective of this paper is to investigate the relative significance of the various theories for the time-dependent strength of SiCSiC composites. This is achieved through the development of a numerically-based progressive failure analysis routine and through the application of the routine to simulate the composite stress rupture tests. The progressive failure routine is a time marching routine with an iterative loop between a probability of fiber survival equation and a force equilibrium equation within each time step. Failure of the composite is assumed to initiate near a matrix crack and the progression of fiber failures occurs by global load sharing. The probability of survival equation is derived from consideration of the strength of ceramic fibers with randomly occurring and slow growing flaws as well as the mechanical interaction between the fibers and matrix near a matrix crack. The force equilibrium equation follows from the global load sharing presumption. The results of progressive failure analyses of the composite tests suggest that the relationship between time and stress-rupture strength is attributed almost entirely to the slow flaw growth within the fibers. Although other mechanisms may be present, they appear to have only a minor influence on the observed time dependent behavior.
Towards Social Radiology as an Information Infrastructure: Reconciling the Local With the Global
2014-01-01
The current widespread use of medical images and imaging procedures in clinical practice and patient diagnosis has brought about an increase in the demand for sharing medical imaging studies among health professionals in an easy and effective manner. This article reveals the existence of a polarization between the local and global demands for radiology practice. While there are no major barriers for sharing such studies, when access is made from a (local) picture archive and communication system (PACS) within the domain of a healthcare organization, there are a number of impediments for sharing studies among health professionals on a global scale. Social radiology as an information infrastructure involves the notion of a shared infrastructure as a public good, affording a social space where people, organizations and technical components may spontaneously form associations in order to share clinical information linked to patient care and radiology practice. This article shows however, that such polarization establishes a tension between local and global demands, which hinders the emergence of social radiology as an information infrastructure. Based on an analysis of the social space for radiology practice, the present article has observed that this tension persists due to the inertia of a locally installed base in radiology departments, for which common teleradiology models are not truly capable of reorganizing as a global social space for radiology practice. Reconciling the local with the global signifies integrating PACS and teleradiology into an evolving, secure, heterogeneous, shared, open information infrastructure where the conceptual boundaries between (local) PACS and (global) teleradiology are transparent, signaling the emergence of social radiology as an information infrastructure. PMID:25600710
Fogel, Guy R; Li, Zhenyu; Liu, Weiqiang; Liao, Zhenhua; Wu, Jia; Zhou, Wenyu
2010-05-01
Anterior cervical plating has been accepted in corpectomy and fusion of the cervical spine. Constrained plates were criticized for stress shielding that may lead to subsidence and pseudarthrosis. A dynamic plate allows load sharing as the graft subsides. Ideally, the dynamic plate design should maintain adequate stiffness of the construct while providing a reasonable load sharing with the strut graft. The purpose of the study was to compare dynamic and static plate kinematics with graft subsidence. The study designed was an in vitro biomechanical study in a porcine cervical spine model. Twelve spines were initially tested in intact condition with 20-N axial load in 15 degrees of flexion and extension range of motion (ROM). Then, a two-level corpectomy was created in all specimens with spines randomized to receive either a static or dynamic plate. The spines were retested under identical conditions with optimal length and undersized graft. Range of motion and graft loading were analyzed with a one-way analysis of variance (p<.05). Both plates significantly limited ROM compared with the intact spine in both graft length conditions. In extension graft, load was significantly higher (p=.001) in the static plate with optimal length, and in flexion, there was a significant loss of graft load (p=.0004). In flexion, the dynamic plate with undersized graft demonstrated significantly more load sustained (p=.0004). Both plates reasonably limited the ROM of the corpectomy. The static plate had significantly higher graft loads in extension and significant loss of graft load in flexion, whereas the dynamic plate maintained a reasonable graft load in ROM even when graft contact was imperfect. Copyright 2010 Elsevier Inc. All rights reserved.
NASA Technical Reports Server (NTRS)
Ray, Richard D.; Egbert, G. D.
2003-01-01
The small S$_1$ ocean tide is caused primarily by diurnal atmospheric pressure loading. Its excitation is therefore unlike any other diurnal tide. The global character of $S-1$ is here determined by numerical modeling and by analysis of Topex/Poseidon satellite altimeter data. The two approaches yield reasonably consistent results, and large ( $ greater than $l\\cm) amplitudes in several regions are further confirmed by comparison with coastal tide gauges. Notwithstanding their excitation differences, S$-1$ and other diurnal tides are found to share several common features, such as relatively large amplitudes in the Arabian Sea, the Sea of Okhotsk, and the Gulf of Alaska. The most noticeable difference is the lack of an S$-1$ Antarctic Kelvin wave. These similarities and differences can be explained in terms of the coherences between near-diurnal oceanic normal modes and the underlying tidal forcings. While gravitational diurnal tidal forces excite primarily a 28-hour Antarctic-Pacific mode, the S$_1$ air tide excites several other near-diurnal modes, none of which has large amplitudes near Antarctica.
NASA Technical Reports Server (NTRS)
Hailperin, Max
1993-01-01
This thesis provides design and analysis of techniques for global load balancing on ensemble architectures running soft-real-time object-oriented applications with statistically periodic loads. It focuses on estimating the instantaneous average load over all the processing elements. The major contribution is the use of explicit stochastic process models for both the loading and the averaging itself. These models are exploited via statistical time-series analysis and Bayesian inference to provide improved average load estimates, and thus to facilitate global load balancing. This thesis explains the distributed algorithms used and provides some optimality results. It also describes the algorithms' implementation and gives performance results from simulation. These results show that our techniques allow more accurate estimation of the global system load ing, resulting in fewer object migration than local methods. Our method is shown to provide superior performance, relative not only to static load-balancing schemes but also to many adaptive methods.
Lessons Learned and Global Partnerships: Stories of Sexual and Reproductive Health from Namibia
ERIC Educational Resources Information Center
Maurer, Lis; Kelly, Maureen
2005-01-01
Through a Global Partnership Project, Planned Parenthood of the Southern Finger Lakes in Ithaca, New York and the Namibian Planned Parenthood Association (NAPPA) in Windhoek, Namibia have joined together to share best practices, technical assistance, support, and resources. The Global Partners share the common goal of increasing awareness,…
National Culture in Practice: Its Impact on Knowledge Sharing in Global Virtual Collaboration
ERIC Educational Resources Information Center
Wei, Kangning
2009-01-01
Issues concerning global virtual collaboration have received considerable attention in both the academic and practical world; however, little research has been conducted on knowledge-sharing activities in global virtual collaboration, which is a key process to achieve collaboration effectiveness. Due to national culture having been seen as one of…
NASA Technical Reports Server (NTRS)
Hailperin, M.
1993-01-01
This thesis provides design and analysis of techniques for global load balancing on ensemble architectures running soft-real-time object-oriented applications with statistically periodic loads. It focuses on estimating the instantaneous average load over all the processing elements. The major contribution is the use of explicit stochastic process models for both the loading and the averaging itself. These models are exploited via statistical time-series analysis and Bayesian inference to provide improved average load estimates, and thus to facilitate global load balancing. This thesis explains the distributed algorithms used and provides some optimality results. It also describes the algorithms' implementation and gives performance results from simulation. These results show that the authors' techniques allow more accurate estimation of the global system loading, resulting in fewer object migrations than local methods. The authors' method is shown to provide superior performance, relative not only to static load-balancing schemes but also to many adaptive load-balancing methods. Results from a preliminary analysis of another system and from simulation with a synthetic load provide some evidence of more general applicability.
Global-scale tectonic patterns on Pluto
NASA Astrophysics Data System (ADS)
Matsuyama, I.; Keane, J. T.; Kamata, S.
2016-12-01
The New Horizons spacecraft revealed a global-scale tectonic pattern on the surface of Pluto which is presumably related to its formation and early evolution. Changes in the rotational and tidal potentials, expansion, and loading can generate stresses capable of producing global-scale tectonic patterns. The current alignment of Sputnik Planum with the tidal axis suggests a reorientation of Pluto relative to the rotation and tidal axes, or true polar wander. This reorientation can be driven by mass loading associated with Sputnik Planum. We developed a general theoretical formalism for the calculation of tectonic patterns due to a variety of process including true polar wander, loading, and expansion. The formalism is general enough to be applicable to non-axisymmetric loads. We illustrate that the observed global-scale tectonic pattern can be explained by stresses generated by true polar wander, Sputnik Planum loading, and expansion.
A 10 bit 200 MS/s pipeline ADC using loading-balanced architecture in 0.18 μm CMOS
NASA Astrophysics Data System (ADS)
Wang, Linfeng; Meng, Qiao; Zhi, Hao; Li, Fei
2017-07-01
A new loading-balanced architecture for high speed and low power consumption pipeline analog-to-digital converter (ADC) is presented in this paper. The proposed ADC uses SHA-less, op-amp and capacitor-sharing technique, capacitor-scaling scheme to reduce the die area and power consumption. A new capacitor-sharing scheme was proposed to cancel the extra reset phase of the feedback capacitors. The non-standard inter-stage gain increases the feedback factor of the first stage and makes it equal to the second stage, by which, the load capacitor of op-amp shared by the first and second stages is balanced. As for the fourth stage, the capacitor and op-amp no longer scale down. From the system’s point of view, all load capacitors of the shared OTAs are balanced by employing a loading-balanced architecture. The die area and power consumption are optimized maximally. The ADC is implemented in a 0.18 μm 1P6M CMOS technology, and occupies a die area of 1.2 × 1.2 mm{}2. The measurement results show a 55.58 dB signal-to-noise-and-distortion ratio (SNDR) and 62.97 dB spurious-free dynamic range (SFDR) with a 25 MHz input operating at a 200 MS/s sampling rate. The proposed ADC consumes 115 mW at 200 MS/s from a 1.8 V supply.
Viewing benefit sharing in global health research through the lens of Aristotelian justice.
Dauda, Bege; Dierickx, Kris
2017-06-01
The ethics of benefit sharing has been a topical issue in global health research in resource-limited countries. It pertains to the distribution of goods, benefits and advantages to the research participants, communities and countries that are involved in research. One of the nuances in benefit sharing is the ethical justification on which the concept should be based. Extensive literature outlining the different principles underlying benefit sharing is available. The purpose of this paper is to examine the proposed principles using Aristotelian principles of justice. The paper assesses the central idea of Aristotelian justice and applies and evaluates this idea to benefit sharing in research, especially when commercial research sponsors conduct research in resource-limited countries. Two categories of Aristotelian justice-universal and particular-were examined and their contribution to the benefit-sharing discourse assessed. On the one hand, benefit sharing in accordance with universal justice requires that for-profit research sponsors obey the legal regulations and international standards set for benefit sharing. On the other hand, benefit sharing in accordance with particular justice transcends obeying legal requirements and standards to a realm of acting in an ethically accepted manner. Accordingly, the paper further examines three perspectives of particular justice and develops ethical justification for benefit sharing in global health research. As Aristotelian justice is still relevant to the contemporary discourse on justice, this paper broadens the ethical justifications of benefit sharing in global health research. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.
Federal Register 2010, 2011, 2012, 2013, 2014
2013-11-12
... Change Proposing to Amend the Rule Governing the Listing and Trading of Shares of the WisdomTree Global... change to the means of achieving the investment objective applicable to the WisdomTree Global Real Return... Rule 8.600 \\4\\ (``Managed Fund Shares'').\\5\\ The Shares are offered by the WisdomTree Trust (``Trust...
Federal Register 2010, 2011, 2012, 2013, 2014
2012-10-25
... Relating to the Listing and Trading of Shares of the WisdomTree Global Corporate Bond Fund of the WisdomTree Trust October 19, 2012. I. Introduction On August 15, 2012, The NASDAQ Stock Market LLC (``Nasdaq... proposed rule change to list and trade the shares (``Shares'') of the WisdomTree Global Corporate Bond Fund...
Dynamic load balancing of applications
Wheat, Stephen R.
1997-01-01
An application-level method for dynamically maintaining global load balance on a parallel computer, particularly on massively parallel MIMD computers. Global load balancing is achieved by overlapping neighborhoods of processors, where each neighborhood performs local load balancing. The method supports a large class of finite element and finite difference based applications and provides an automatic element management system to which applications are easily integrated.
Federal Register 2010, 2011, 2012, 2013, 2014
2012-02-16
... and Trading of the PIMCO Global Advantage Inflation-Linked Bond Strategy Fund Under NYSE Arca Equities...''): PIMCO Global Advantage Inflation-Linked Bond Strategy Fund. The text of the proposed rule change is... Shares \\3\\ (``Shares'') under NYSE Arca Equities Rule 8.600: PIMCO Global Advantage Inflation-Linked Bond...
Heuristic approaches for energy-efficient shared restoration in WDM networks
NASA Astrophysics Data System (ADS)
Alilou, Shahab
In recent years, there has been ongoing research on the design of energy-efficient Wavelength Division Multiplexing (WDM) networks. The explosive growth of Internet traffic has led to increased power consumption of network components. Network survivability has also been a relevant research topic, as it plays a crucial role in assuring continuity of service with no disruption, regardless of network component failure. Network survivability mechanisms tend to utilize considerable resources such as spare capacity in order to protect and restore information. This thesis investigates techniques for reducing energy demand and enhancing energy efficiency in the context of network survivability. We propose two novel heuristic energy-efficient shared protection approaches for WDM networks. These approaches intend to save energy by setting on sleep mode devices that are not being used while providing shared backup paths to satisfy network survivability. The first approach exploits properties of a math series in order to assign weight to the network links. It aims at reducing power consumption at the network indirectly by aggregating traffic on a set of nodes and links with high traffic load level. Routing traffic on links and nodes that are already under utilization makes it possible for the links and nodes with no load to be set on sleep mode. The second approach is intended to dynamically route traffic through nodes and links with high traffic load level. Similar to the first approach, this approach computes a pair of paths for every newly arrived demand. It computes these paths for every new demand by comparing the power consumption of nodes and links in the network before the demand arrives with their potential power consumption if they are chosen along the paths of this demand. Simulations of two different networks were used to compare the total network power consumption obtained using the proposed techniques against a standard shared-path restoration scheme. Shared-path restoration is a network survivability method in which a link-disjoint backup path and wavelength is reserved at the time of call setup for a working path. However, in order to reduce spare capacity consumption, this reserved backup path and wavelength may be shared with other backup paths. Pool Sharing Scheme (PSS) is employed to implement shared-path restoration scheme [1]. In an optical network, the failure of a single link leads to the failure of all the lightpaths that pass through that particular link. PSS ensures that the amount of backup bandwidth required on a link to restore the failed connections will not be more than the total amount of reserved backup bandwidth on that link. Simulation results indicate that the proposed approaches lead to up to 35% power savings in WDM networks when traffic load is low. However, power saving decreases to 14% at high traffic load level. Furthermore, in terms of the total capacity consumption for working paths, PSS outperforms the two proposed approaches, as expected. In terms of total capacity consumption all the approaches behave similarly. In general, at low traffic load level, the two proposed approaches behave similar to PSS in terms of average link load, and the ratio of block demands. Nevertheless, at high traffic load, the proposed approaches result in higher ratio of blocked demands than PSS. They also lead to higher average link load than PSS for the equal number of generated demands.
van Puijenbroek, P J T M; Bouwman, A F; Beusen, A H W; Lucas, P L
2015-01-01
Households are an important source of nutrient loading to surface water. Sewage systems without or with only primary wastewater treatment are major polluters of surface water. Future emission levels will depend on population growth, urbanisation, increases in income and investments in sanitation, sewage systems and wastewater treatment plants. This study presents the results for two possible shared socioeconomic pathways (SSPs). SSP1 is a scenario that includes improvement of wastewater treatment and SSP3 does not include such improvement, with fewer investments and a higher population growth. The main drivers for the nutrient emission model are population growth, income growth and urbanisation. Under the SSP1 scenario, 5.7 billion people will be connected to a sewage system and for SSP3 this is 5 billion. Nitrogen and phosphorus emissions increase by about 70% under both SSP scenarios, with the largest increase in SSP1. South Asia and Africa have the largest emission increases, in the developed countries decrease the nutrient emissions. The higher emission level poses a risk to ecosystem services.
Dynamic load balancing of applications
Wheat, S.R.
1997-05-13
An application-level method for dynamically maintaining global load balance on a parallel computer, particularly on massively parallel MIMD computers is disclosed. Global load balancing is achieved by overlapping neighborhoods of processors, where each neighborhood performs local load balancing. The method supports a large class of finite element and finite difference based applications and provides an automatic element management system to which applications are easily integrated. 13 figs.
Compressive buckling analysis of hat-stiffened panel
NASA Technical Reports Server (NTRS)
Ko, William L.; Jackson, Raymond H.
1991-01-01
Buckling analysis was performed on a hat-stiffened panel subjected to uniaxial compression. Both local buckling and global buckling were analyzed. It was found that the global buckling load was several times higher than the buckling load. The predicted local buckling loads compared favorably with both experimental data and finite-element analysis.
The effective forces transmitted by high-speed, low-amplitude thoracic manipulation.
Herzog, W; Kats, M; Symons, B
2001-10-01
Twenty asymptomatic volunteers each received three spinal manipulative treatments to the thoracic spine. The treatments consisted of a straight posterior-to-anterior high-speed, low-amplitude thrust to the transverse process of T3-T10 using a reinforced hypothenar contact. All treatments were given by a full-time practicing clinician with 3 years of experience. The primary objective of this study was to quantify local measures of loading applied by the clinician on the volunteers during spinal manipulative treatments and to compare these local measures of loading with previously described global measures. The sparse information on the mechanics of spinal manipulative treatments deals exclusively with global force or pressure measurements. On the basis of these global data, incorrect conclusions may be drawn about the beneficial effects of spinal manipulative therapy, the loading of internal structures, and the risks associated with these treatments. Twenty asymptomatic subjects each received three posterior-to-anterior, high-speed, low-amplitude spinal manipulative treatments to the transverse process of the thoracic spine. Total force, local force, contact area, peak pressure, and average pressure at the contact interface between clinician and subject were measured continuously by use of a thin, flexible pressure pad. Local and global measures of loading were compared and analyzed by use of nonparametric statistics (alpha = 0.01). The average peak total force was 238.2 N. The average peak local force over a target area of 25 mm2 was 5 N, indicating that global measures of loading vastly overestimate the local effective forces at the target site. The peak pressure point moved, on average, 9.8 mm during the course of the manipulation. To the authors' best knowledge, this is the first study to quantify local, effective measures of loading and compare them with the global measures typically used. The conclusions are limited because the study used a single clinician. The effective loading of specific target sites is much smaller than the global measures might suggest. This result occurs because as the forces during spinal manipulative treatment increase, so does the contact area; therefore, much of the total treatment force is taken up by non-target-specific tissues. Because of the vast discrepancy between the global and local measures of loading, it is suggested that risk-benefit assessments of high-speed, low-amplitude spinal manipulative treatments should be made, including local measures of loading. Finally, because theoretical approaches and the inverse dynamics approach can provide only global measures of loading, the results of such studies should be interpreted with caution.
Estimating lithospheric properties at Atla Regio, Venus
NASA Technical Reports Server (NTRS)
Phillips, Roger J.
1994-01-01
Magellan spehrical harmonic gravity and topography models are used to estimate lithospheric properties at Alta Regio, Venus, a proposed hotspot with dynamic support from mantle plume(s). Global spherical harmonic and local representations of the gravity field share common properties in the Atla region interms of their spectral behavior over a wavelength band from approximately 2100 to approximately 700 km. The estimated free-air admittance spectrum displays a rather featureless long-wavelength portion followed by a sharp rise at wavelengths shorter than about 1000 km. This sharp rise requires significant flexural support of short-wavelength structures. The Bouguer coherence also displays a sharp drop in this wavelength band, indicating a finite flexural rigidity of the lithosphere. A simple model for lithospheric loading from above and below is introduced (D. W. Forsyth, 1985) with four parameters: f, the ratio of bottom loading to top loading; z(sub m), crustal thickness; z(sub l) depth to bottom loading source; and T(sub e) elastic lithosphere thickness. A dual-mode compensation model is introduced in which the shorter wavelengths (lambda approximately less than 1000 km) might be explained best by a predominance of top loading by the large shield volcanoes Maat Mons, Ozza Mons, and Sapas Mons, and the longer wavelengths (lambda approximately greater than 1500 km) might be explained best by a deep depth of compensation, possibly representing bottom loading by a dynamic source. A Monte Carlo inversion technique is introduced to thoroughly search out the four-space of the model parameters and to examine parameter correlation in the solutions. Venus either is a considerabe deficient in heat sources relative to Earth, or the thermal lithosphere is overthickened in response to an earlier episode of significant heat loss from the planet.
Shear buckling analysis of a hat-stiffened panel
NASA Technical Reports Server (NTRS)
Ko, William L.; Jackson, Raymond H.
1994-01-01
A buckling analysis was performed on a hat-stiffened panel subjected to shear loading. Both local buckling and global buckling were analyzed. The global shear buckling load was found to be several times higher than the local shear buckling load. The classical shear buckling theory for a flat plate was found to be useful in predicting the local shear buckling load of the hat-stiffened panel, and the predicted local shear buckling loads thus obtained compare favorably with the results of finite element analysis.
Friedman, Jason; Latash, Mark L.; Zatsiorsky, Vladimir M.
2009-01-01
We examined how the digit forces adjust when a load force acting on a hand-held object continuously varies. The subjects were required to hold the handle still while a linearly increasing and then decreasing force was applied to the handle. The handle was constrained, such that it could only move up and down, and rotate about a horizontal axis. In addition the moment arm of the thumb tangential force was 1.5 times the moment arm of the virtual finger (VF, an imagined finger with the mechanical action equal to that of the four fingers) force. Unlike the situation when there are equal moment arms, the experimental setup forced the subjects to choose between (a) sharing equally the increase in load force between the thumb and virtual finger but generating a moment of tangential force, which had to be compensated by negatively covarying the moment due to normal forces, or (b) sharing unequally the load force increase between the thumb and VF but preventing generation of a moment of tangential forces. We found that different subjects tended to use one of these two strategies. These findings suggest that the selection by the CNS of prehension synergies at the VF-thumb level with respect to the moment of force are non-obligatory and reflect individual subject preferences. This unequal sharing of the load by the tangential forces, in contrast to the previously observed equal sharing, suggests that the invariant feature of prehension may be a correlated increase in tangential forces rather than an equal increase. PMID:19554319
The global position of the U S forest products industry
Jeffrey P. Prestemon; David N. Wear; Michaela O. Foster
2015-01-01
The United Statesâ share of global industrial roundwood production has declined since the 1990s. We reviewed data from 1961-2013 to evaluate the extent of this decline for industrial roundwood and derived secondary forest products compared to other major producing countries. We find that the U.S. global share of industrial roundwood peaked at 28 percent in 1999 but...
Mechanical Failure Mode of Metal Nanowires: Global Deformation versus Local Deformation
Ho, Duc Tam; Im, Youngtae; Kwon, Soon-Yong; Earmme, Youn Young; Kim, Sung Youb
2015-01-01
It is believed that the failure mode of metal nanowires under tensile loading is the result of the nucleation and propagation of dislocations. Such failure modes can be slip, partial slip or twinning and therefore they are regarded as local deformation. Here we provide numerical and theoretical evidences to show that global deformation is another predominant failure mode of nanowires under tensile loading. At the global deformation mode, nanowires fail with a large contraction along a lateral direction and a large expansion along the other lateral direction. In addition, there is a competition between global and local deformations. Nanowires loaded at low temperature exhibit global failure mode first and then local deformation follows later. We show that the global deformation originates from the intrinsic instability of the nanowires and that temperature is a main parameter that decides the global or local deformation as the failure mode of nanowires. PMID:26087445
Distributed Load Shedding over Directed Communication Networks with Time Delays
DOE Office of Scientific and Technical Information (OSTI.GOV)
Yang, Tao; Wu, Di
When generation is insufficient to support all loads under emergencies, effective and efficient load shedding needs to be deployed in order to maintain the supply-demand balance. This paper presents a distributed load shedding algorithm, which makes efficient decision based on the discovered global information. In the global information discovery process, each load only communicates with its neighboring load via directed communication links possibly with arbitrarily large but bounded time varying communication delays. We propose a novel distributed information discovery algorithm based on ratio consensus. Simulation results are used to validate the proposed method.
ERIC Educational Resources Information Center
Andia, Jonny F.; Deren, Sherry; Robles, Rafaela R.; Kang, Sung-Yeon; Colon, Hector M.
2008-01-01
This study examines the influence of peer norms on sharing of injection paraphernalia (e.g., indirect sharing behaviors, including sharing of cookers, cotton, rinse water and back/front loading) among Puerto Rican injection drug users (IDUs) in Bayamon, Puerto Rico, and East Harlem, New York City. Data were collected from 873 Puerto Rican IDUs…
Global Mental Health: sharing and synthesizing knowledge for sustainable development.
O'Donnell, K; O'Donnell, M Lewis
2016-01-01
Global mental health (GMH) is a growing domain with an increasing capacity to positively impact the world community's efforts for sustainable development and wellbeing. Sharing and synthesizing GMH and multi-sectoral knowledge, the focus of this paper, is an important way to support these global efforts. This paper consolidates some of the most recent and relevant 'context resources' [global multi-sector (GMS) materials, emphasizing world reports on major issues] and 'core resources' (GMH materials, including newsletters, texts, conferences, training, etc.). In addition to offering a guided index of materials, it presents an orientation framework (global integration) to help make important information as accessible and useful as possible. Mental health colleagues are encouraged to stay current in GMH and global issues, to engage in the emerging agendas for sustainable development and wellbeing, and to intentionally connect and contribute across sectors. Colleagues in all sectors are encouraged to do likewise, and to take advantage of the wealth of shared and synthesized knowledge in the GMH domain, such as the materials featured in this paper.
US forest products in the global economy
Dave N Wear; Jeff Prestemon; Michaela O. Foster
2015-01-01
The United Statesâ shares of global industrial roundwood production and derivative products have declined precipitously since the 1990s. We evaluate the extent of these declines compared with those of major producing countries from 1961 to 2013. We find that the US global share of industrial roundwood peaked at 28% in 1999 but by 2013 was at 17%, with the decline...
Parallel processing approach to transform-based image coding
NASA Astrophysics Data System (ADS)
Normile, James O.; Wright, Dan; Chu, Ken; Yeh, Chia L.
1991-06-01
This paper describes a flexible parallel processing architecture designed for use in real time video processing. The system consists of floating point DSP processors connected to each other via fast serial links, each processor has access to a globally shared memory. A multiple bus architecture in combination with a dual ported memory allows communication with a host control processor. The system has been applied to prototyping of video compression and decompression algorithms. The decomposition of transform based algorithms for decompression into a form suitable for parallel processing is described. A technique for automatic load balancing among the processors is developed and discussed, results ar presented with image statistics and data rates. Finally techniques for accelerating the system throughput are analyzed and results from the application of one such modification described.
Building Intercultural Understandings through Global Literature
ERIC Educational Resources Information Center
Martens, Prisca; Martens, Ray; Doyle, Michelle Hassay; Loomis, Jenna; Fuhrman, Laura; Furnari, Christie; Soper, Elizabeth; Stout, Robbie
2015-01-01
In this article the authors share how they use global literature picturebooks with pre-kindergarten, kindergarten, and first grade children in the context of A Curriculum That is International to develop the children's intercultural understandings. The picturebooks, shared through read alouds, individual and partner reading, and browsing, is…
Load Sharing in Anti-Air Warfare Coordination: Criteria and a Simulation Test Plan
1991-09-01
NAVAL POSTGRADUATE SCHOOL Monterey, California AD-A245 968 DTIG EB 18 199Z THESIS L LOAD SHARING IN ANTI-AIR WARFARE COORDINATION: CRITERIA AND A...REPORT NUMBER(S) Ga. NAME OF PERFORMING ORGANIZATION Gb. OFFICE SYMBOL 71. NAME OF MONITORING ORGANIZATION Naval Postgraduate School OR 6c. ADDRESS...the degree of MASTER OF SCIENCE IN OPERATIONS RESEARCH from the NAVAL POSTGRADUATE SCHOOL September 1991 Au thor: ’ysviL-’ / ; d Stephen Hue Keley
Analysis and performance of paralleling circuits for modular inverter-converter systems
NASA Technical Reports Server (NTRS)
Birchenough, A. G.; Gourash, F.
1972-01-01
As part of a modular inverter-converter development program, control techniques were developed to provide load sharing among paralleled inverters or converters. An analysis of the requirements of paralleling circuits and a discussion of the circuits developed and their performance are included in this report. The current sharing was within 5.6 percent of rated-load current for the ac modules and 7.4 percent for the dc modules for an initial output voltage unbalance of 5 volts.
Global Practices of Interprofessional Education (IPE) and Relevant International Activities.
Arakawa, Naoko
2017-01-01
Activities related to interprofessional education (IPE) vary between countries according to local and national health needs and systems. The International Pharmaceutical Federation (FIP) Education Initiative endeavors to provide a global vision in IPE by the sharing of experiences and gathering of evidence collaboratively to facilitate country-level initiatives. The purpose of this paper is to contribute to the further development of IPE activities in pharmacy in Japan through sharing global perspectives and activities related to IPE. FIP Education Initiative published the Interprofessional Education in a Pharmacy Context: Global Report in September 2015, which marked a milestone in the growing recognition of IPE in pharmacy globally. The paper shared global and regional perspectives and experiences in IPE in pharmacy, both from the report and FIP activities. This paper can be seen as a snapshot of IPE-related international activities, which enables gaps and challenges in implementing IPE activities in Japan to be identified. This paper provides an opportunity to explore global trends and initiatives regarding IPE, and to consider how to form and implement IPE specifically based on Japanese health needs and systems.
NASA Astrophysics Data System (ADS)
Xie, Hua; Ringler, Claudia
2017-10-01
Human activities, in particular agricultural production, interfere with natural cycles of nutrient elements, nitrogen (N) and phosphorus (P), leading to growing concerns about water quality degradation related to excessive nutrient loadings. Increases in agricultural production in response to population growth and wealth generation further increase risks associated with nutrient pollution. This paper presents results from projections of nutrient exports from global agricultural crop and pasture systems to the water environment generated using a process-based modeling approach. Brazil, China, India and the United States account for more than half of estimated global N and P loadings in the base year. Each country boasts large agriculture centers where high calculated loading values are found. Rapid growth in global agricultural nutrient loadings is projected. Growth of agricultural pollution loading is fastest in the group of low-income developing countries and loading growth rates also vary substantially with climate change scenario. Counter measures need to be taken to address the environmental risks associated with the projected rapid increase of agricultural nutrient loadings.
Does Education Lower Allostatic Load? A Co-twin Control Study
Hamdi, Nayla R.; South, Susan C.; Krueger, Robert F.
2016-01-01
Many studies have found that education is associated with better health, but the causal basis of this association is unclear. The current study used a co-twin control design to examine if differences in years of education within twin pairs predict allostatic load. The strength of this design is that it controls for genetic and other familial confounds shared between twins. The sample consisted of 381 twins (with 292 twins from 146 complete pairs; mean age=57; 61% female) who participated in the biomarker project of the Midlife Development in the United States (MIDUS) study. Individual-level analyses showed a significant, negative association between years of education and allostatic load, but this association was explained entirely by familial influences shared between twins. The results of this study suggest that schooling does not itself protect against allostatic load. PMID:26778778
Eckermann, Simon; Willan, Andrew R
2013-05-01
Risk sharing arrangements relate to adjusting payments for new health technologies given evidence of their performance over time. Such arrangements rely on prospective information regarding the incremental net benefit of the new technology, and its use in practice. However, once the new technology has been adopted in a particular jurisdiction, randomized clinical trials within that jurisdiction are likely to be infeasible and unethical in the cases where they would be most helpful, i.e. with current evidence of positive while uncertain incremental health and net monetary benefit. Informed patients in these cases would likely be reluctant to participate in a trial, preferring instead to receive the new technology with certainty. Consequently, informing risk sharing arrangements within a jurisdiction is problematic given the infeasibility of collecting prospective trial data. To overcome such problems, we demonstrate that global trials facilitate trialling post adoption, leading to more complete and robust risk sharing arrangements that mitigate the impact of costs of reversal on expected value of information in jurisdictions who adopt while a global trial is undertaken. More generally, optimally designed global trials offer distinct advantages over locally optimal solutions for decision makers and manufacturers alike: avoiding opportunity costs of delay in jurisdictions that adopt; overcoming barriers to evidence collection; and improving levels of expected implementation. Further, the greater strength and translatability of evidence across jurisdictions inherent in optimal global trial design reduces barriers to translation across jurisdictions characteristic of local trials. Consequently, efficiently designed global trials better align the interests of decision makers and manufacturers, increasing the feasibility of risk sharing and the expected strength of evidence over local trials, up until the point that current evidence is globally sufficient.
Leek, E Charles; Roberts, Mark; Oliver, Zoe J; Cristino, Filipe; Pegna, Alan J
2016-08-01
Here we investigated the time course underlying differential processing of local and global shape information during the perception of complex three-dimensional (3D) objects. Observers made shape matching judgments about pairs of sequentially presented multi-part novel objects. Event-related potentials (ERPs) were used to measure perceptual sensitivity to 3D shape differences in terms of local part structure and global shape configuration - based on predictions derived from hierarchical structural description models of object recognition. There were three types of different object trials in which stimulus pairs (1) shared local parts but differed in global shape configuration; (2) contained different local parts but shared global configuration or (3) shared neither local parts nor global configuration. Analyses of the ERP data showed differential amplitude modulation as a function of shape similarity as early as the N1 component between 146-215ms post-stimulus onset. These negative amplitude deflections were more similar between objects sharing global shape configuration than local part structure. Differentiation among all stimulus types was reflected in N2 amplitude modulations between 276-330ms. sLORETA inverse solutions showed stronger involvement of left occipitotemporal areas during the N1 for object discrimination weighted towards local part structure. The results suggest that the perception of 3D object shape involves parallel processing of information at local and global scales. This processing is characterised by relatively slow derivation of 'fine-grained' local shape structure, and fast derivation of 'coarse-grained' global shape configuration. We propose that the rapid early derivation of global shape attributes underlies the observed patterns of N1 amplitude modulations. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.
Grip force and force sharing in two different manipulation tasks with bottles.
Cepriá-Bernal, Javier; Pérez-González, Antonio; Mora, Marta C; Sancho-Bru, Joaquín L
2017-07-01
Grip force and force sharing during two activities of daily living were analysed experimentally in 10 right-handed subjects. Four different bottles, filled to two different levels, were manipulated for two tasks: transporting and pouring. Each test subject's hand was instrumented with eight thin wearable force sensors. The grip force and force sharing were significantly different for each bottle model. Increasing the filling level resulted in an increase in grip force, but the ratio of grip force to load force was higher for lighter loads. The task influenced the force sharing but not the mean grip force. The contributions of the thumb and ring finger were higher in the pouring task, whereas the contributions of the palm and the index finger were higher in the transport task. Mean force sharing among fingers was 30% for index, 29% for middle, 22% for ring and 19% for little finger. Practitioner Summary: We analysed grip force and force sharing in two manipulation tasks with bottles: transporting and pouring. The objective was to understand the effects of the bottle features, filling level and task on the contribution of different areas of the hand to the grip force. Force sharing was different for each task and the bottles features affected to both grip force and force sharing.
Pushing HTCondor and glideinWMS to 200K+ Jobs in a Global Pool for CMS before Run 2
NASA Astrophysics Data System (ADS)
Balcas, J.; Belforte, S.; Bockelman, B.; Gutsche, O.; Khan, F.; Larson, K.; Letts, J.; Mascheroni, M.; Mason, D.; McCrea, A.; Saiz-Santos, M.; Sfiligoi, I.
2015-12-01
The CMS experiment at the LHC relies on HTCondor and glideinWMS as its primary batch and pilot-based Grid provisioning system. So far we have been running several independent resource pools, but we are working on unifying them all to reduce the operational load and more effectively share resources between various activities in CMS. The major challenge of this unification activity is scale. The combined pool size is expected to reach 200K job slots, which is significantly bigger than any other multi-user HTCondor based system currently in production. To get there we have studied scaling limitations in our existing pools, the biggest of which tops out at about 70K slots, providing valuable feedback to the development communities, who have responded by delivering improvements which have helped us reach higher and higher scales with more stability. We have also worked on improving the organization and support model for this critical service during Run 2 of the LHC. This contribution will present the results of the scale testing and experiences from the first months of running the Global Pool.
What role do hurricanes play in sediment delivery to subsiding river deltas?
Smith, James E.; Bentley, Samuel J.; Snedden, Gregg; White, Crawford
2015-01-01
The Mississippi River Delta (MRD) has undergone tremendous land loss over the past century due to natural and anthropogenic influences, a fate shared by many river deltas globally. A globally unprecedented effort to restore and sustain the remaining subaerial portions of the delta is now underway, an endeavor that is expected to cost $50–100B over the next 50 yr. Success of this effort requires a thorough understanding of natural and anthropogenic controls on sediment supply and delta geomorphology. In the MRD, hurricanes have been paradoxically identified as both substantial agents of widespread land loss, and vertical marsh sediment accretion. We present the first multi-decadal chronostratigraphic assessment of sediment supply for a major coastal basin of the MRD that assesses both fluvial and hurricane-induced contributions to sediment accumulation in deltaic wetlands. Our findings indicate that over multidecadal timescales, hurricane-induced sediment delivery may be an important contributor for deltaic wetland vertical accretion, but the contribution from hurricanes to long-term sediment accumulation is substantially less than sediment delivery supplied by existing and planned river-sediment diversions at present-day river-sediment loads.
What Role do Hurricanes Play in Sediment Delivery to Subsiding River Deltas?
NASA Astrophysics Data System (ADS)
Smith, James E.; Bentley, Samuel J.; Snedden, Gregg A.; White, Crawford
2015-12-01
The Mississippi River Delta (MRD) has undergone tremendous land loss over the past century due to natural and anthropogenic influences, a fate shared by many river deltas globally. A globally unprecedented effort to restore and sustain the remaining subaerial portions of the delta is now underway, an endeavor that is expected to cost $50-100B over the next 50 yr. Success of this effort requires a thorough understanding of natural and anthropogenic controls on sediment supply and delta geomorphology. In the MRD, hurricanes have been paradoxically identified as both substantial agents of widespread land loss, and vertical marsh sediment accretion. We present the first multi-decadal chronostratigraphic assessment of sediment supply for a major coastal basin of the MRD that assesses both fluvial and hurricane-induced contributions to sediment accumulation in deltaic wetlands. Our findings indicate that over multidecadal timescales, hurricane-induced sediment delivery may be an important contributor for deltaic wetland vertical accretion, but the contribution from hurricanes to long-term sediment accumulation is substantially less than sediment delivery supplied by existing and planned river-sediment diversions at present-day river-sediment loads.
Planetary Load Sharing in Three-Point- Mounted Wind Turbine Gearboxes: Preprint
DOE Office of Scientific and Technical Information (OSTI.GOV)
Guo, Yi; Keller, Jonathan A
Wind turbine gearboxes do not achieve their expected design life. The cost of gearbox replacements and rebuilds and the downtime associated with these failures increase the cost of wind energy. In 2007, the U.S. Department of Energy established the National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC). Its goals are to understand the root causes of premature gearbox failures and improve their reliability. To date, the GRC has focused on a 750-kW drivetrain with a three-stage, three-point-mounted gearbox. A nonproprietary version of the gearbox containing CRBs with C3 clearances in the planetary stage was customized. Two of these gearboxes,more » GB1 and GB2, were manufactured and then tested in the National Wind Technology Center's 2.5-MW dynamometer and in the field. Major GRC findings include the detrimental effect of rotor moments on planetary load sharing and predicted fatigue, and the risk of bearing sliding in low-torque conditions for three-point configuration drivetrains. Based on the knowledge gained from testing and analysis of the original design, the GRC gearbox was redesigned to improve its load-sharing characteristics and predicted fatigue. This new gearbox is named GB3. As shown in Figure 1, its key improvement is the incorporation of preloaded TRBs that support the planet carrier and planets. Roller loads can be optimized and bearing life maximized with a small preload [4]. These preloaded bearings, along with interference-fitted planet pins, improve alignments and load-sharing characteristics. A semi-integrated planet bearing design also increases capacity and eliminates outer race fretting. Romax Technology, with Powertrain Engineers and the Timken Company (Timken), completed the redesign. Timken manufactured and instrumented the planet gears and bearings. Brad Foote Gearing manufactured the other gearing and assembled the gearbox.« less
Enhancing and Transforming Global Learning Communities with Augmented Reality
ERIC Educational Resources Information Center
Frydenberg, Mark; Andone, Diana
2018-01-01
Augmented and virtual reality applications bring new insights to real world objects and scenarios. This paper shares research results of the TalkTech project, an ongoing study investigating the impact of learning about new technologies as members of global communities. This study shares results of a collaborative learning project about augmented…
Time-dependent fiber bundles with local load sharing.
Newman, W I; Phoenix, S L
2001-02-01
Fiber bundle models, where fibers have random lifetimes depending on their load histories, are useful tools in explaining time-dependent failure in heterogeneous materials. Such models shed light on diverse phenomena such as fatigue in structural materials and earthquakes in geophysical settings. Various asymptotic and approximate theories have been developed for bundles with various geometries and fiber load-sharing mechanisms, but numerical verification has been hampered by severe computational demands in larger bundles. To gain insight at large size scales, interest has returned to idealized fiber bundle models in 1D. Such simplified models typically assume either equal load sharing (ELS) among survivors, or local load sharing (LLS) where a failed fiber redistributes its load onto its two nearest flanking survivors. Such models can often be solved exactly or asymptotically in increasing bundle size, N, yet still capture the essence of failure in real materials. The present work focuses on 1D bundles under LLS. As in previous works, a fiber has failure rate following a power law in its load level with breakdown exponent rho. Surviving fibers under fixed loads have remaining lifetimes that are independent and exponentially distributed. We develop both new asymptotic theories and new computational algorithms that greatly increase the bundle sizes that can be treated in large replications (e.g., one million fibers in thousands of realizations). In particular we develop an algorithm that adapts several concepts and methods that are well-known among computer scientists, but relatively unknown among physicists, to dramatically increase the computational speed with no attendant loss of accuracy. We consider various regimes of rho that yield drastically different behavior as N increases. For 1/2< or =rho< or =1, ELS and LLS have remarkably similar behavior (they have identical lifetime distributions at rho=1) with approximate Gaussian bundle lifetime statistics and a finite limiting mean. For rho>1 this Gaussian behavior also applies to ELS, whereas LLS behavior diverges sharply showing brittle, weakest volume behavior in terms of characteristic elements derived from critical cluster formation. For 0
Sharing Data to Build a Medical Information Commons: From Bermuda to the Global Alliance.
Cook-Deegan, Robert; Ankeny, Rachel A; Maxson Jones, Kathryn
2017-08-31
The Human Genome Project modeled its open science ethos on nematode biology, most famously through daily release of DNA sequence data based on the 1996 Bermuda Principles. That open science philosophy persists, but daily, unfettered release of data has had to adapt to constraints occasioned by the use of data from individual people, broader use of data not only by scientists but also by clinicians and individuals, the global reach of genomic applications and diverse national privacy and research ethics laws, and the rising prominence of a diverse commercial genomics sector. The Global Alliance for Genomics and Health was established to enable the data sharing that is essential for making meaning of genomic variation. Data-sharing policies and practices will continue to evolve as researchers, health professionals, and individuals strive to construct a global medical and scientific information commons.
Influence of inclination angles on intra- and inter-limb load-sharing during uphill walking.
Hong, Shih-Wun; Leu, Tsai-Hsueh; Li, Jia-Da; Wang, Ting-Ming; Ho, Wei-Ping; Lu, Tung-Wu
2014-01-01
Uphill walking is an inevitable part of daily living, placing more challenges on the locomotor system with greater risk of falls than level walking does. The current study aimed to investigate the effects of inclination angles on the inter-joint and inter-limb load-sharing during uphill walking in terms of total support moment and contributions of individual joint moments to the total support moment. Fifteen young adults walked up walkways with 0°, 5°, 10° and 15° of slope while kinematic and kinetic data were collected and analyzed. With increasing inclination angles, the first peak of the total support moment was increased with unaltered individual joint contributions, suggesting an unaltered inter-joint control pattern in the leading limb to meet the increased demands. The second peak of the total support moment remained unchanged with increasing inclination angles primarily through a compensatory redistribution of the hip and knee moments. During DLS, the leading limb shared the majority of the whole body support moments. The current results reveal basic intra- and inter-limb load-sharing patterns of uphill walking, which will be helpful for a better understanding of the control strategies adopted and for subsequent clinical applications. Copyright © 2013 Elsevier B.V. All rights reserved.
Inattentional Deafness: Visual Load Leads to Time-Specific Suppression of Auditory Evoked Responses
Molloy, Katharine; Griffiths, Timothy D.; Lavie, Nilli
2015-01-01
Due to capacity limits on perception, conditions of high perceptual load lead to reduced processing of unattended stimuli (Lavie et al., 2014). Accumulating work demonstrates the effects of visual perceptual load on visual cortex responses, but the effects on auditory processing remain poorly understood. Here we establish the neural mechanisms underlying “inattentional deafness”—the failure to perceive auditory stimuli under high visual perceptual load. Participants performed a visual search task of low (target dissimilar to nontarget items) or high (target similar to nontarget items) load. On a random subset (50%) of trials, irrelevant tones were presented concurrently with the visual stimuli. Brain activity was recorded with magnetoencephalography, and time-locked responses to the visual search array and to the incidental presence of unattended tones were assessed. High, compared to low, perceptual load led to increased early visual evoked responses (within 100 ms from onset). This was accompanied by reduced early (∼100 ms from tone onset) auditory evoked activity in superior temporal sulcus and posterior middle temporal gyrus. A later suppression of the P3 “awareness” response to the tones was also observed under high load. A behavioral experiment revealed reduced tone detection sensitivity under high visual load, indicating that the reduction in neural responses was indeed associated with reduced awareness of the sounds. These findings support a neural account of shared audiovisual resources, which, when depleted under load, leads to failures of sensory perception and awareness. SIGNIFICANCE STATEMENT The present work clarifies the neural underpinning of inattentional deafness under high visual load. The findings of near-simultaneous load effects on both visual and auditory evoked responses suggest shared audiovisual processing capacity. Temporary depletion of shared capacity in perceptually demanding visual tasks leads to a momentary reduction in sensory processing of auditory stimuli, resulting in inattentional deafness. The dynamic “push–pull” pattern of load effects on visual and auditory processing furthers our understanding of both the neural mechanisms of attention and of cross-modal effects across visual and auditory processing. These results also offer an explanation for many previous failures to find cross-modal effects in experiments where the visual load effects may not have coincided directly with auditory sensory processing. PMID:26658858
Empirical comparison of heuristic load distribution in point-to-point multicomputer networks
NASA Technical Reports Server (NTRS)
Grunwald, Dirk C.; Nazief, Bobby A. A.; Reed, Daniel A.
1990-01-01
The study compared several load placement algorithms using instrumented programs and synthetic program models. Salient characteristics of these program traces (total computation time, total number of messages sent, and average message time) span two orders of magnitude. Load distribution algorithms determine the initial placement for processes, a precursor to the more general problem of load redistribution. It is found that desirable workload distribution strategies will place new processes globally, rather than locally, to spread processes rapidly, but that local information should be used to refine global placement.
NASA Astrophysics Data System (ADS)
Chanard, Kristel; Fleitout, Luce; Calais, Eric; Rebischung, Paul; Avouac, Jean-Philippe
2018-04-01
We model surface displacements induced by variations in continental water, atmospheric pressure, and nontidal oceanic loading, derived from the Gravity Recovery and Climate Experiment (GRACE) for spherical harmonic degrees two and higher. As they are not observable by GRACE, we use at first the degree-1 spherical harmonic coefficients from Swenson et al. (2008, https://doi.org/10.1029/2007JB005338). We compare the predicted displacements with the position time series of 689 globally distributed continuous Global Navigation Satellite System (GNSS) stations. While GNSS vertical displacements are well explained by the model at a global scale, horizontal displacements are systematically underpredicted and out of phase with GNSS station position time series. We then reestimate the degree 1 deformation field from a comparison between our GRACE-derived model, with no a priori degree 1 loads, and the GNSS observations. We show that this approach reconciles GRACE-derived loading displacements and GNSS station position time series at a global scale, particularly in the horizontal components. Assuming that they reflect surface loading deformation only, our degree-1 estimates can be translated into geocenter motion time series. We also address and assess the impact of systematic errors in GNSS station position time series at the Global Positioning System (GPS) draconitic period and its harmonics on the comparison between GNSS and GRACE-derived annual displacements. Our results confirm that surface mass redistributions observed by GRACE, combined with an elastic spherical and layered Earth model, can be used to provide first-order corrections for loading deformation observed in both horizontal and vertical components of GNSS station position time series.
Preparing Global-Ready Teachers
ERIC Educational Resources Information Center
Larson, Lotta; Brown, Jennifer S.
2017-01-01
To produce global-ready students who can thrive and compete in an interconnected world, we must prepare global-ready teachers. This article shares how one teacher preparation program focuses on literacy, technology, and globalization, while offering relevant K-12 applications.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Not Available
1985-07-01
The report presents the results of a feasibility study for the National Load Dispatch Center and Global Communications System Project in Guatemala. The project consists of a communication system which will provide Institute Nacional de Electrificacion (INDE) operations personnel direct voice access to all major power system facilities. In addition, a modern computer based load dispatch center has been configured on a secure and reliable basis to provide automatic generation control of all major interconnected generating plants within Guatemala.
Analysis of DMFC/battery hybrid power system for portable applications
NASA Astrophysics Data System (ADS)
Lee, Bong-Do; Jung, Doo-Hwan; Ko, Young-Ho
This study was carried out to develop a direct methanol fuel cell (DMFC)/battery hybrid power system used in portable applications. For a portable power system, the DMFC was applied for the main power source at average load and the battery was applied for auxiliary power at overload. Load share characteristics of hybrid power source were analyzed by computational simulation. The connection apparatus between the DMFC and the battery was set and investigated in the real system. Voltages and currents of the load, the battery and the DMFC were measured according to fuel, air and load changes. The relationship between load share characteristic and battery capacity was surveyed. The relationship was also studied in abnormal operation. A DMFC stack was manufactured for this experiment. For the study of the connection characteristics to the fuel cell Pb-acid, Ni-Cd and Ni-MH batteries were tested. The results of this study can be applied to design the interface module of the fuel cell/battery hybrid system and to determine the design requirement in the fuel cell stack for portable applications.
Load balancing for massively-parallel soft-real-time systems
DOE Office of Scientific and Technical Information (OSTI.GOV)
Hailperin, M.
1988-09-01
Global load balancing, if practical, would allow the effective use of massively-parallel ensemble architectures for large soft-real-problems. The challenge is to replace quick global communications, which is impractical in a massively-parallel system, with statistical techniques. In this vein, the author proposes a novel approach to decentralized load balancing based on statistical time-series analysis. Each site estimates the system-wide average load using information about past loads of individual sites and attempts to equal that average. This estimation process is practical because the soft-real-time systems of interest naturally exhibit loads that are periodic, in a statistical sense akin to seasonality in econometrics.more » It is shown how this load-characterization technique can be the foundation for a load-balancing system in an architecture employing cut-through routing and an efficient multicast protocol.« less
Federal Register 2010, 2011, 2012, 2013, 2014
2011-03-10
... . DATES: The meeting will take place on Wednesday, April 20, 2011, from 8:30 a.m. to 4 p.m. ET. ADDRESSES: The meeting will take place at the Embassy Suites Washington, DC--Convention Center Hotel, 900 Tenth... priorities. The GAC will guide and monitor the development of the Global information sharing concept. It will...
Vergauwe, Evie; Hartstra, Egbert; Barrouillet, Pierre; Brass, Marcel
2015-07-15
Working memory is often defined in cognitive psychology as a system devoted to the simultaneous processing and maintenance of information. In line with the time-based resource-sharing model of working memory (TBRS; Barrouillet and Camos, 2015; Barrouillet et al., 2004), there is accumulating evidence that, when memory items have to be maintained while performing a concurrent activity, memory performance depends on the cognitive load of this activity, independently of the domain involved. The present study used fMRI to identify regions in the brain that are sensitive to variations in cognitive load in a domain-general way. More precisely, we aimed at identifying brain areas that activate during maintenance of memory items as a direct function of the cognitive load induced by both verbal and spatial concurrent tasks. Results show that the right IFJ and bilateral SPL/IPS are the only areas showing an increased involvement as cognitive load increases and do so in a domain general manner. When correlating the fMRI signal with the approximated cognitive load as defined by the TBRS model, it was shown that the main focus of the cognitive load-related activation is located in the right IFJ. The present findings indicate that the IFJ makes domain-general contributions to time-based resource-sharing in working memory and allowed us to generate the novel hypothesis by which the IFJ might be the neural basis for the process of rapid switching. We argue that the IFJ might be a crucial part of a central attentional bottleneck in the brain because of its inability to upload more than one task rule at once. Copyright © 2015 Elsevier Inc. All rights reserved.
Effects of mass loading on dayside solar wind-magnetosphere interactions
NASA Astrophysics Data System (ADS)
Zhang, B.; Brambles, O.; Wiltberger, M. J.; Lyon, J.; Lotko, W.
2016-12-01
Satellite observations have shown that terrestrial-sourced plasmas mass load the dayside magnetopause and cause reductions in local reconnection rates. Whether the integrated dayside reconnection rate is affected by these local mass-loading processes is still an open question. Several mechanisms have been proposed to describe the control of dayside reconnection, including the local-control and global-control hypotheses. We have conducted a series of controlled numerical simulations to investigate the response of dayside solar wind-magnetopshere (SW-M) coupling to mass loading processes. Our simulation results show that the coupled SW-M system may exhibit both local and global control behaviors depending on the amount of mass loading. With a small amount of mass loading, the changes in the local reconnection rate does not affect magnetosheath properties and the geoeffective length in the upstream solar wind, resulting in the same integrated dayside reconnection rate. With a large amount of mass loading, the magnetosheath properties and the geoeffective length are significantly modified by slowing down the local reconnection rate, resulting in a significant reduction in the integrated dayside reconnection rate. The response of magnetosheath properties to mass loading is expected from the Cassak-Shay asymmetric reconnection theory through conservation of energy. The physical origin of the transition regime between local and global control is qualitatively explained. The parameters that determine the transition regime depend on the location, spatial extension and density of the mass loading process.
Detecting local haplotype sharing and haplotype association
USDA-ARS?s Scientific Manuscript database
A novel haplotype association method is presented, and its power is demonstrated. Relying on a statistical model for linkage disequilibrium (LD), the method first infers ancestral haplotypes and their loadings at each marker for each individual. The loadings are then used to quantify local haplotype...
Automatic load sharing in inverter modules
NASA Technical Reports Server (NTRS)
Nagano, S.
1979-01-01
Active feedback loads transistor equally with little power loss. Circuit is suitable for balancing modular inverters in spacecraft, computer power supplies, solar-electric power generators, and electric vehicles. Current-balancing circuit senses differences between collector current for power transistor and average value of load currents for all power transistors. Principle is effective not only in fixed duty-cycle inverters but also in converters operating at variable duty cycles.
Inter-Philosophies Dialogue: Creating a Paradigm for Global Health Ethics.
Benatar, Solomon; Daibes, Ibrahim; Tomsons, Sandra
While debate remains about the definition and goals of work on global health, there is growing agreement that our moral starting point is the reality of unjust inequalities in the distribution of the conditions necessary for human health and well-being. With the growth of multi-jurisdictional and multicultural global health partnerships, the adequacy of the prevailing bioethical paradigm guiding the conduct of global health research and practice is being increasingly challenged. In response to ethical challenges and conflicts confronted by decision-makers in global health research and practice, we propose an innovative methodology that could be developed to bridge the gap between polarized systems of ideas and values (metaphysical, epistemological, moral, and political). Our inter-philosophies methodology provides the potential to construct a new, shared paradigm for global health ethics, thereby increasing the capacity for solidarity and shared decision-making in global health research and practice.
Ramayah, T; Yeap, Jasmine A L; Ignatius, Joshua
2014-04-01
There is a belief that academics tend to hold on tightly to their knowledge and intellectual resources. However, not much effort has been put into the creation of a valid and reliable instrument to measure knowledge sharing behavior among the academics. To apply and validate the Knowledge Sharing Behavior Scale (KSBS) as a measure of knowledge sharing behavior within the academic community. Respondents (N = 447) were academics from arts and science streams in 10 local, public universities in Malaysia. Data were collected using the 28-item KSBS that assessed four dimensions of knowledge sharing behavior namely written contributions, organizational communications, personal interactions, and communities of practice. The exploratory factor analysis showed that the items loaded on the dimension constructs that they were supposed to represent, thus proving construct validity. A within-factor analysis revealed that each set of items representing their intended dimension loaded on only one construct, therefore establishing convergent validity. All four dimensions were not perfectly correlated with each other or organizational citizenship behavior, thereby proving discriminant validity. However, all four dimensions correlated with organizational commitment, thus confirming predictive validity. Furthermore, all four factors correlated with both tacit and explicit sharing, which confirmed their concurrent validity. All measures also possessed sufficient reliability (α > .70). The KSBS is a valid and reliable instrument that can be used to formally assess the types of knowledge artifacts residing among academics and the degree of knowledge sharing in relation to those artifacts. © The Author(s) 2014.
Federal Register 2010, 2011, 2012, 2013, 2014
2011-05-10
... WisdomTree Global Real Return Fund May 5, 2011. Pursuant to Section 19(b)(1) of the Securities Exchange... Exchange proposes to list and trade the shares (``Shares'') of the following series of the WisdomTree Trust (``Trust'') under NYSE Arca Equities Rule 8.600: WisdomTree Global Real Return Fund (``Fund''). The text of...
Planetary gear profile modification design based on load sharing modelling
NASA Astrophysics Data System (ADS)
Iglesias, Miguel; Fernández Del Rincón, Alfonso; De-Juan, Ana Magdalena; Garcia, Pablo; Diez, Alberto; Viadero, Fernando
2015-07-01
In order to satisfy the increasing demand on high performance planetary transmissions, an important line of research is focused on the understanding of some of the underlying phenomena involved in this mechanical system. Through the development of models capable of reproduce the system behavior, research in this area contributes to improve gear transmission insight, helping developing better maintenance practices and more efficient design processes. A planetary gear model used for the design of profile modifications ratio based on the levelling of the load sharing ratio is presented. The gear profile geometry definition, following a vectorial approach that mimics the real cutting process of gears, is thoroughly described. Teeth undercutting and hypotrochoid definition are implicitly considered, and a procedure for the incorporation of a rounding arc at the tooth tip in order to deal with corner contacts is described. A procedure for the modeling of profile deviations is presented, which can be used for the introduction of both manufacturing errors and designed profile modifications. An easy and flexible implementation of the profile deviation within the planetary model is accomplished based on the geometric overlapping. The contact force calculation and dynamic implementation used in the model are also introduced, and parameters from a real transmission for agricultural applications are presented for the application example. A set of reliefs is designed based on the levelling of the load sharing ratio for the example transmission, and finally some other important dynamic factors of the transmission are analyzed to assess the changes in the dynamic behavior with respect to the non-modified case. Thus, the main innovative aspect of the proposed planetary transmission model is the capacity of providing a simulated load sharing ratio which serves as design variable for the calculation of the tooth profile modifications.
NASA Astrophysics Data System (ADS)
Richter, A.; Müller, L.; Marderwald, E.; Mendoza, L.; Kruse, E.; Perdomo, R.; Scheinert, M.; Perdomo, S.
2017-02-01
We present a regionalized model of ocean tidal loading effects for the Argentine-German Geodetic Observatory in La Plata. It provides the amplitudes and phases of gravity variations and vertical deformation for nine tidal constituents to be applied as corrections to the observatory's future geodetic observation data. This model combines a global ocean tide model with a model of the tides in the Río de la Plata estuary. A comparison with conventional predictions based only on the global ocean tide model reveals the importance of the incorporation of the regional tide model. Tidal loading at the observatory is dominated by the tides in the Atlantic Ocean. An additional contribution of local tidal loading in channels and groundwater is examined. The magnitude of the tidal loading is also reviewed in the context of the effects of solid earth tides, atmospheric loading and non-tidal loads.
Parallel Processing of Adaptive Meshes with Load Balancing
NASA Technical Reports Server (NTRS)
Das, Sajal K.; Harvey, Daniel J.; Biswas, Rupak; Biegel, Bryan (Technical Monitor)
2001-01-01
Many scientific applications involve grids that lack a uniform underlying structure. These applications are often also dynamic in nature in that the grid structure significantly changes between successive phases of execution. In parallel computing environments, mesh adaptation of unstructured grids through selective refinement/coarsening has proven to be an effective approach. However, achieving load balance while minimizing interprocessor communication and redistribution costs is a difficult problem. Traditional dynamic load balancers are mostly inadequate because they lack a global view of system loads across processors. In this paper, we propose a novel and general-purpose load balancer that utilizes symmetric broadcast networks (SBN) as the underlying communication topology, and compare its performance with a successful global load balancing environment, called PLUM, specifically created to handle adaptive unstructured applications. Our experimental results on an IBM SP2 demonstrate that the SBN-based load balancer achieves lower redistribution costs than that under PLUM by overlapping processing and data migration.
Pushing HTCondor and glideinWMS to 200K+ Jobs in a Global Pool for CMS before Run 2
DOE Office of Scientific and Technical Information (OSTI.GOV)
Balcas, J.; Belforte, S.; Bockelman, B.
2015-12-23
The CMS experiment at the LHC relies on HTCondor and glideinWMS as its primary batch and pilot-based Grid provisioning system. So far we have been running several independent resource pools, but we are working on unifying them all to reduce the operational load and more effectively share resources between various activities in CMS. The major challenge of this unification activity is scale. The combined pool size is expected to reach 200K job slots, which is significantly bigger than any other multi-user HTCondor based system currently in production. To get there we have studied scaling limitations in our existing pools, themore » biggest of which tops out at about 70K slots, providing valuable feedback to the development communities, who have responded by delivering improvements which have helped us reach higher and higher scales with more stability. We have also worked on improving the organization and support model for this critical service during Run 2 of the LHC. This contribution will present the results of the scale testing and experiences from the first months of running the Global Pool.« less
Ocean Tide Loading Computation
NASA Technical Reports Server (NTRS)
Agnew, Duncan Carr
2005-01-01
September 15,2003 through May 15,2005 This grant funds the maintenance, updating, and distribution of programs for computing ocean tide loading, to enable the corrections for such loading to be more widely applied in space- geodetic and gravity measurements. These programs, developed under funding from the CDP and DOSE programs, incorporate the most recent global tidal models developed from Topex/Poscidon data, and also local tide models for regions around North America; the design of the algorithm and software makes it straightforward to combine local and global models.
ERIC Educational Resources Information Center
Song, Minjung; Bruning, Roger
2016-01-01
This study was designed to explore the effects of different geographical background contexts and signalling for information about global warming on comprehension, recall and cognitive load. Two different geographical contexts, US and Korean, were employed to frame explanations of global warming phenomena to US students. Two signalling conditions…
Global changes in DNA methylation in Alzheimer's disease peripheral blood mononuclear cells.
Di Francesco, Andrea; Arosio, Beatrice; Falconi, Anastasia; Micioni Di Bonaventura, Maria Vittoria; Karimi, Mohsen; Mari, Daniela; Casati, Martina; Maccarrone, Mauro; D'Addario, Claudio
2015-03-01
Changes in epigenetic marks may help explain the late onset of Alzheimer's disease (AD). In this study we measured genome-wide DNA methylation by luminometric methylation assay, a quantitative measurement of genome-wide DNA methylation, on DNA isolated from peripheral blood mononuclear cells of 37 subjects with late-onset AD (LOAD) and 44 healthy controls (CT). We found an increase in global DNA methylation in LOAD subjects compared to CT (p=0.0122), associated with worse cognitive performances (p=0.0002). DNA hypermethylation in LOAD group was paralleled by higher DNA methyltransferase 1 (DNMT1) gene expression and protein levels. When data were stratified on the basis of the APOE polymorphisms, higher DNA methylation levels were associated with the presence of APOE ε4 allele (p=0.0043) in the global population. Among the APOE ε3 carriers, a significant increase of DNA methylation was still observed in LOAD patients compared to healthy controls (p=0.05). Our data suggest global DNA methylation in peripheral samples as a useful marker for screening individuals at risk of developing AD. Copyright © 2014 Elsevier Inc. All rights reserved.
NASA Astrophysics Data System (ADS)
Tadić, Bosiljka; Thurner, Stefan; Rodgers, G. J.
2004-03-01
We study the microscopic time fluctuations of traffic load and the global statistical properties of a dense traffic of particles on scale-free cyclic graphs. For a wide range of driving rates R the traffic is stationary and the load time series exhibits antipersistence due to the regulatory role of the superstructure associated with two hub nodes in the network. We discuss how the superstructure affects the functioning of the network at high traffic density and at the jamming threshold. The degree of correlations systematically decreases with increasing traffic density and eventually disappears when approaching a jamming density Rc. Already before jamming we observe qualitative changes in the global network-load distributions and the particle queuing times. These changes are related to the occurrence of temporary crises in which the network-load increases dramatically, and then slowly falls back to a value characterizing free flow.
Sofaer, Helen R.; Jarnevich, Catherine S.
2017-01-01
AimThe distributions of exotic species reflect patterns of human-mediated dispersal, species climatic tolerances and a suite of other biotic and abiotic factors. The relative importance of each of these factors will shape how the spread of exotic species is affected by ongoing economic globalization and climate change. However, patterns of trade may be correlated with variation in scientific sampling effort globally, potentially confounding studies that do not account for sampling patterns.LocationGlobal.Time periodMuseum records, generally from the 1800s up to 2015.Major taxa studiedPlant species exotic to the United States.MethodsWe used data from the Global Biodiversity Information Facility (GBIF) to summarize the number of plant species with exotic occurrences in the United States that also occur in each other country world-wide. We assessed the relative importance of trade and climatic similarity for explaining variation in the number of shared species while evaluating several methods to account for variation in sampling effort among countries.ResultsAccounting for variation in sampling effort reversed the relative importance of trade and climate for explaining numbers of shared species. Trade was strongly correlated with numbers of shared U.S. exotic plants between the United States and other countries before, but not after, accounting for sampling variation among countries. Conversely, accounting for sampling effort strengthened the relationship between climatic similarity and species sharing. Using the number of records as a measure of sampling effort provided a straightforward approach for the analysis of occurrence data, whereas species richness estimators and rarefaction were less effective at removing sampling bias.Main conclusionsOur work provides support for broad-scale climatic limitation on the distributions of exotic species, illustrates the need to account for variation in sampling effort in large biodiversity databases, and highlights the difficulty in inferring causal links between the economic drivers of invasion and global patterns of exotic species occurrence.
SAHAYOG: A Testbed for Load Sharing under Failure,
1987-07-01
messages, shared memory and semaphores . To communicate using messages, processes create message queues using system-provided prim- itives. The message...The size of the memory that is to be shared is decided by the process when it makes a request for memory allocation. The semaphore option of IPC can be...used to prevent two or more concurrent processes from executing their critical sections at the same time. Semaphores must be used when the processes
A cache-aided multiprocessor rollback recovery scheme
NASA Technical Reports Server (NTRS)
Wu, Kun-Lung; Fuchs, W. Kent
1989-01-01
This paper demonstrates how previous uniprocessor cache-aided recovery schemes can be applied to multiprocessor architectures, for recovering from transient processor failures, utilizing private caches and a global shared memory. As with cache-aided uniprocessor recovery, the multiprocessor cache-aided recovery scheme of this paper can be easily integrated into standard bus-based snoopy cache coherence protocols. A consistent shared memory state is maintained without the necessity of global check-pointing.
Religious affiliation at time of death - Global estimates and projections.
Skirbekk, Vegard; Todd, Megan; Stonawski, Marcin
2018-03-01
Religious affiliation influences societal practices regarding death and dying, including palliative care, religiously acceptable health service procedures, funeral rites and beliefs about an afterlife. We aimed to estimate and project religious affiliation at the time of death globally, as this information has been lacking. We compiled data on demographic information and religious affiliation from more than 2500 surveys, registers and censuses covering 198 nations/territories. We present estimates of religious affiliation at the time of death as of 2010, projections up to and including 2060, taking into account trends in mortality, religious conversion, intergenerational transmission of religion, differential fertility, and gross migration flows, by age and sex. We find that Christianity continues to be the most common religion at death, although its share will fall from 37% to 31% of global deaths between 2010 and 2060. The share of individuals identifying as Muslim at the time of death increases from 21% to 24%. The share of religiously unaffiliated will peak at 17% in 2035 followed by a slight decline thereafter. In specific regions, such as Europe, the unaffiliated share will continue to rises from 14% to 21% throughout the period. Religious affiliation at the time of death is changing globally, with distinct regional patterns. This could affect spatial variation in healthcare and social customs relating to death and dying.
Time and Cognitive Load in Working Memory
ERIC Educational Resources Information Center
Barrouillet, Pierre; Bernardin, Sophie; Portrat, Sophie; Vergauwe, Evie; Camos, Valerie
2007-01-01
According to the time-based resource-sharing model (P. Barrouillet, S. Bernardin, & V. Camos, 2004), the cognitive load a given task involves is a function of the proportion of time during which it captures attention, thus impeding other attention-demanding processes. Accordingly, the present study demonstrates that the disruptive effect on…
NASA Astrophysics Data System (ADS)
Gordeev, Evgeny; Sergeev, Victor; Tsyganenko, Nikolay; Kuznetsova, Maria; Rastaetter, Lutz; Raeder, Joachim; Toth, Gabor; Lyon, John; Merkin, Vyacheslav; Wiltberger, Michael
2017-04-01
In this study we investigate how well the three community-available global MHD models, supported by the Community Coordinated Modeling Center (CCMC NASA), reproduce the global magnetospheric dynamics, including the loading-unloading substorm cycle. We found that in terms of global magnetic flux transport CCMC models display systematically different response to idealized 2-hour north then 2-hour south IMF Bz variation. The LFM model shows a depressed return convection in the tail plasma sheet and high rate of magnetic flux loading into the lobes during the growth phase, as well as enhanced return convection and high unloading rate during the expansion phase, with the amount of loaded/unloaded magnetotail flux and the growth phase duration being the closest to their observed empirical values during isolated substorms. BATSRUS and Open GGCM models exhibit drastically different behavior. In the BATS-R-US model the plasma sheet convection shows a smooth transition to the steady convection regime after the IMF southward turning. In the Open GGCM a weak plasma sheet convection has comparable intensities during both the growth phase and the following slow unloading phase. Our study shows that different CCMC models under the same solar wind conditions (north to south IMF variation) produce essentially different solutions in terms of global magnetospheric convection.
Xie, Zilong; Reetzke, Rachel; Chandrasekaran, Bharath
2018-05-24
Increasing visual perceptual load can reduce pre-attentive auditory cortical activity to sounds, a reflection of the limited and shared attentional resources for sensory processing across modalities. Here, we demonstrate that modulating visual perceptual load can impact the early sensory encoding of speech sounds, and that the impact of visual load is highly dependent on the predictability of the incoming speech stream. Participants (n = 20, 9 females) performed a visual search task of high (target similar to distractors) and low (target dissimilar to distractors) perceptual load, while early auditory electrophysiological responses were recorded to native speech sounds. Speech sounds were presented either in a 'repetitive context', or a less predictable 'variable context'. Independent of auditory stimulus context, pre-attentive auditory cortical activity was reduced during high visual load, relative to low visual load. We applied a data-driven machine learning approach to decode speech sounds from the early auditory electrophysiological responses. Decoding performance was found to be poorer under conditions of high (relative to low) visual load, when the incoming acoustic stream was predictable. When the auditory stimulus context was less predictable, decoding performance was substantially greater for the high (relative to low) visual load conditions. Our results provide support for shared attentional resources between visual and auditory modalities that substantially influence the early sensory encoding of speech signals in a context-dependent manner. Copyright © 2018 IBRO. Published by Elsevier Ltd. All rights reserved.
Fatigue Life Prediction of 2D Woven Ceramic-Matrix Composites at Room and Elevated Temperatures
NASA Astrophysics Data System (ADS)
Longbiao, Li
2017-03-01
In this paper, the fatigue life of 2D woven ceramic-matrix composites, i.e., SiC/SiC, SiC/Si-N-C, SiC/Si-B4C, and Nextel 610™/Aluminosilicate, at room and elevated temperatures has been predicted using the micromechanics approach. An effective coefficient of the fiber volume fraction along the loading direction (ECFL) was introduced to describe the fiber architecture of preforms. The Budiansky-Hutchinson-Evans shear-lag model was used to describe the microstress field of the damaged composite considering fibers failure. The statistical matrix multicracking model and fracture mechanics interface debonding criterion were used to determine the matrix crack spacing and interface debonded length. The interface shear stress and fibers strength degradation model and oxidation region propagation model have been adopted to analyze the fatigue and oxidation effects on fatigue life of the composite, which is controlled by interface frictional slip and diffusion of oxygen gas through matrix multicrackings. Under cyclic fatigue loading, the fibers broken fraction was determined by combining the interface/fiber oxidation model, interface wear model and fibers statistical failure model at elevated temperatures, based on the assumption that the fiber strength is subjected to two-parameter Weibull distribution and the load carried by broken and intact fibers satisfy the Global Load Sharing (GLS) criterion. When the broken fibers fraction approaches to the critical value, the composites fatigue fractures. The fatigue life S- N curves of 2D SiC/SiC, SiC/Si-N-C, SiC/Si-B4C, and Nextel 610™/Aluminosilicate composites at room temperature and 800, 1000 and 1200 °C in air and steam have been predicted.
Modeling nitrous oxide emission from rivers: a global assessment.
Hu, Minpeng; Chen, Dingjiang; Dahlgren, Randy A
2016-11-01
Estimates of global riverine nitrous oxide (N 2 O) emissions contain great uncertainty. We conducted a meta-analysis incorporating 169 observations from published literature to estimate global riverine N 2 O emission rates and emission factors. Riverine N 2 O flux was significantly correlated with NH 4 , NO 3 and DIN (NH 4 + NO 3 ) concentrations, loads and yields. The emission factors EF(a) (i.e., the ratio of N 2 O emission rate and DIN load) and EF(b) (i.e., the ratio of N 2 O and DIN concentrations) values were comparable and showed negative correlations with nitrogen concentration, load and yield and water discharge, but positive correlations with the dissolved organic carbon : DIN ratio. After individually evaluating 82 potential regression models based on EF(a) or EF(b) for global, temperate zone and subtropical zone datasets, a power function of DIN yield multiplied by watershed area was determined to provide the best fit between modeled and observed riverine N 2 O emission rates (EF(a): R 2 = 0.92 for both global and climatic zone models, n = 70; EF(b): R 2 = 0.91 for global model and R 2 = 0.90 for climatic zone models, n = 70). Using recent estimates of DIN loads for 6400 rivers, models estimated global riverine N 2 O emission rates of 29.6-35.3 (mean = 32.2) Gg N 2 O-N yr -1 and emission factors of 0.16-0.19% (mean = 0.17%). Global riverine N 2 O emission rates are forecasted to increase by 35%, 25%, 18% and 3% in 2050 compared to the 2000s under the Millennium Ecosystem Assessment's Global Orchestration, Order from Strength, Technogarden, and Adapting Mosaic scenarios, respectively. Previous studies may overestimate global riverine N 2 O emission rates (300-2100 Gg N 2 O-N yr -1 ) because they ignore declining emission factor values with increasing nitrogen levels and channel size, as well as neglect differences in emission factors corresponding to different nitrogen forms. Riverine N 2 O emission estimates will be further enhanced through refining emission factor estimates, extending measurements longitudinally along entire river networks and improving estimates of global riverine nitrogen loads. © 2016 John Wiley & Sons Ltd.
Prediction of contact path and load sharing in spiral bevel gears
NASA Technical Reports Server (NTRS)
Bibel, George D.; Tiku, Karuna; Kumar, Ashok
1994-01-01
A procedure is presented to perform a contact analysis of spiral bevel gears in order to predict the contact path and the load sharing as the gears roll through mesh. The approach utilizes recent advances in automated contact methods for nonlinear finite element analysis. A sector of the pinion and gear is modeled consisting of three pinion teeth and four gear teeth in mesh. Calculation of the contact force and stresses through the gear meshing cycle are demonstrated. Summary of the results are presented using three dimensional plots and tables. Issues relating to solution convergence and requirements for running large finite element analysis on a supercomputer are discussed.
Vent modification of large ribbon parachutes to enhance cluster performance
NASA Technical Reports Server (NTRS)
Kolega, D. J.; Woodis, W. R.; Reuter, J. D.
1986-01-01
Due to uneven load sharing and lagging inflation rates, the design of the Large Main Parachute (LMP) cluster, used to recover the Space Shuttle steel case Solid Rocket Boosters, had to be modified. The cause of the problem was excessive variation in effective porosity in the crown area of the LMP during first stage inflation. The design modification consisted of adding horizontal ribbons above the existing vent band to reduce the vent porosity and better control the position and attitude of the vent lines. Performance of modified LMP's since introduction indicates that the load sharing between the clustered chutes has been significantly improved.
Scaling Irregular Applications through Data Aggregation and Software Multithreading
DOE Office of Scientific and Technical Information (OSTI.GOV)
Morari, Alessandro; Tumeo, Antonino; Chavarría-Miranda, Daniel
Bioinformatics, data analytics, semantic databases, knowledge discovery are emerging high performance application areas that exploit dynamic, linked data structures such as graphs, unbalanced trees or unstructured grids. These data structures usually are very large, requiring significantly more memory than available on single shared memory systems. Additionally, these data structures are difficult to partition on distributed memory systems. They also present poor spatial and temporal locality, thus generating unpredictable memory and network accesses. The Partitioned Global Address Space (PGAS) programming model seems suitable for these applications, because it allows using a shared memory abstraction across distributed-memory clusters. However, current PGAS languagesmore » and libraries are built to target regular remote data accesses and block transfers. Furthermore, they usually rely on the Single Program Multiple Data (SPMD) parallel control model, which is not well suited to the fine grained, dynamic and unbalanced parallelism of irregular applications. In this paper we present {\\bf GMT} (Global Memory and Threading library), a custom runtime library that enables efficient execution of irregular applications on commodity clusters. GMT integrates a PGAS data substrate with simple fork/join parallelism and provides automatic load balancing on a per node basis. It implements multi-level aggregation and lightweight multithreading to maximize memory and network bandwidth with fine-grained data accesses and tolerate long data access latencies. A key innovation in the GMT runtime is its thread specialization (workers, helpers and communication threads) that realize the overall functionality. We compare our approach with other PGAS models, such as UPC running using GASNet, and hand-optimized MPI code on a set of typical large-scale irregular applications, demonstrating speedups of an order of magnitude.« less
Domingos, Sara; Fino, Joana; Cardoso, Vânia; Sánchez, Claudia; Ramalho, José C; Larcher, Roberto; Paulo, Octávio S; Oliveira, Cristina M; Goulao, Luis F
2016-02-01
Abscission is a highly coordinated developmental process by which plants control vegetative and reproductive organs load. Aiming at get new insights on flower abscission regulation, changes in the global transcriptome, metabolome and physiology were analyzed in 'Thompson Seedless' grapevine (Vitis vinifera L.) inflorescences, using gibberellic acid (GAc) spraying and shading as abscission stimuli, applied at bloom. Natural flower drop rates increased from 63.1% in non-treated vines to 83% and 99% in response to GAc and shade treatments, respectively. Both treatments had a broad effect on inflorescences metabolism. Specific impacts from shade included photosynthesis inhibition, associated nutritional stress, carbon/nitrogen imbalance and cell division repression, whereas GAc spraying induced energetic metabolism simultaneously with induction of nucleotide biosynthesis and carbon metabolism, therefore, disclosing alternative mechanisms to regulate abscission. Regarding secondary metabolism, changes in flavonoid metabolism were the most represented metabolic pathways in the samples collected following GAc treatment while phenylpropanoid and stilbenoid related pathways were predominantly affected in the inflorescences by the shade treatment. However, both GAc and shade treated inflorescences revealed also shared pathways, that involved the regulation of putrescine catabolism, the repression of gibberellin biosynthesis, the induction of auxin biosynthesis and the activation of ethylene signaling pathways and antioxidant mechanisms, although often the quantitative changes occurred on specific transcripts and metabolites of the pathways. Globally, the results suggest that chemical and environmental cues induced contrasting effects on inflorescence metabolism, triggering flower abscission by different mechanisms and pinpointing the participation of novel abscission regulators. Grapevine showed to be considered a valid model to study molecular pathways of flower abscission competence acquisition, noticeably responding to independent stimuli.
China's international trade and air pollution: 2000 - 2009
NASA Astrophysics Data System (ADS)
Ni, Ruijing; Lin, Jintai; Pan, Da; Wang, Jingxu; Yan, Yingying; Zhang, Qiang
2016-04-01
As the world's top trading country, China is now the most polluted country. However, a large portion of pollution produced in China is associated with its production of goods for foreign consumption via international trade. Along with China's rapid economic growth in recent years, its economic-trade structure and volume has been changing all the time, resulting in large changes in total emissions and the shares of trade-related emissions. Here, we assess the influence of China's changing total and export-related emissions between 2000 and 2009 on its atmospheric pollution loadings and transport, by exploiting simulations of a global chemical transport model GEOS-Chem. We find that both air pollution related to Chinese exports (PRE) which including nitrogen oxides (NOx), sulfur dioxide (SO2), carbon monoxide (CO), black carbon (BC), and primary organic aerosol (POA), and its share in total Chinese pollution have experienced continuous rapid growth until 2007, exposing more and more people to severely polluted air. After 2007, PRE decreases due to strengthened emission controls accompanied by declined exports as a result of the global financial crisis. Although production for exports contribute less than 35% SO2 over China in any year, the increasing trend of trade-related SO2 contributes 51% of integral trend. The changing PRE of China also affects its downwind regions such as the western United States. The contribution of export-related Chinese pollution to surface sulfate concentrations over the western United States has increased from 3% in 2000 to 12% in 2007. Overall, we find that the interannual variation of trade and associated production is a critical factor driving the trend of pollution over China and its downwind regions.
Shared learning in an interconnected world: innovations to advance global health equity
2013-01-01
The notion of “reverse innovation”--that some insights from low-income countries might offer transferable lessons for wealthier contexts--is increasingly common in the global health and business strategy literature. Yet the perspectives of researchers and policymakers in settings where these innovations are developed have been largely absent from the discussion to date. In this Commentary, we present examples of programmatic, technological, and research-based innovations from Rwanda, and offer reflections on how the global health community might leverage innovative partnerships for shared learning and improved health outcomes in all countries. PMID:24119388
Task Group on a Culture of Savings: Implementing Behavior Change in DoD
2011-01-01
Robert Hale Task Group Chairman – Navy Future Personnel and Pay Solution (FPPS) - Business Case November 30, 2009 – Case for Shared Services in the...Public Sector - Accenture Shared Services in Government - AT Kearney – 2009 Global Shared Services Survey Results - Deloitte – Shared Services - a...Benchmark Study - The Johnson Group – Economics of Business Process Outsourcing - Technology Association of Georgia – State of Shared Services and Business
2011-01-01
Shared Services in the Public Sector - Accenture Shared Services in Government - AT Kearney – 2009 Global Shared Services Survey Results - Deloitte... Shared Services - a Benchmark Study - The Johnson Group – Economics of Business Process Outsourcing - Technology Association of Georgia – State of... Shared Services and Business Process Outsourcing - Accenture – Public Sector Outsourcing Surge in 2010 - National Outsourcing Association – Naval
Characterizing output bottlenecks in a supercomputer
DOE Office of Scientific and Technical Information (OSTI.GOV)
Xie, Bing; Chase, Jeffrey; Dillow, David A
2012-01-01
Supercomputer I/O loads are often dominated by writes. HPC (High Performance Computing) file systems are designed to absorb these bursty outputs at high bandwidth through massive parallelism. However, the delivered write bandwidth often falls well below the peak. This paper characterizes the data absorption behavior of a center-wide shared Lustre parallel file system on the Jaguar supercomputer. We use a statistical methodology to address the challenges of accurately measuring a shared machine under production load and to obtain the distribution of bandwidth across samples of compute nodes, storage targets, and time intervals. We observe and quantify limitations from competing traffic,more » contention on storage servers and I/O routers, concurrency limitations in the client compute node operating systems, and the impact of variance (stragglers) on coupled output such as striping. We then examine the implications of our results for application performance and the design of I/O middleware systems on shared supercomputers.« less
A time-shared machine repair problem with mixed spares under N-policy
NASA Astrophysics Data System (ADS)
Jain, Madhu; Shekhar, Chandra; Shukla, Shalini
2016-06-01
The present investigation deals with a machine repair problem consisting of cold and warm standby machines. The machines are subject to breakdown and are repaired by the permanent repairman operating under N-policy. There is provision of one additional removable repairman who is called upon when the work load of failed machines crosses a certain threshold level and is removed as soon as the work load again ceases to that level. Both repairmen recover the failed machines by following the time sharing concept which means that the repairmen share their repair job simultaneously among all the failed machines that have joined the system for repair. Markovian model has been developed by considering the queue dependent rates and solved analytically using the recursive technique. Various performance indices are derived which are further used to obtain the cost function. By taking illustration, numerical simulation and sensitivity analysis have been provided.
Analysis of continuous GPS measurements from southern Victoria Land, Antarctica
Willis, Michael J.
2007-01-01
Several years of continuous data have been collected at remote bedrock Global Positioning System (GPS) sites in southern Victoria Land, Antarctica. Annual to sub-annual variations are observed in the position time-series. An atmospheric pressure loading (APL) effect is calculated from pressure field anomalies supplied by the European Centre for Medium-Range Weather Forecasts (ECMWF) model loading an elastic Earth model. The predicted APL signal has a moderate correlation with the vertical position time-series at McMurdo, Ross Island (International Global Navigation Satellite System Service (IGS) station MCM4), produced using a global solution. In contrast, a local solution in which MCM4 is the fiducial site generates a vertical time series for a remote site in Victoria Land (Cape Roberts, ROB4) which exhibits a low, inverse correlation with the predicted atmospheric pressure loading signal. If, in the future, known and well modeled geophysical loads can be separated from the time-series, then local hydrological loading, of interest for glaciological and climate applications, can potentially be extracted from the GPS time-series.
Residential Solar PV Systems in the Carolinas: Opportunities and Outcomes.
Alqahtani, Bandar Jubran; Holt, Kyra Moore; Patiño-Echeverri, Dalia; Pratson, Lincoln
2016-02-16
This paper presents a first-order analysis of the feasibility and technical, environmental, and economic effects of large levels of solar photovoltaic (PV) penetration within the services areas of the Duke Energy Carolinas (DEC) and Duke Energy Progress (DEP). A PV production model based on household density and a gridded hourly global horizontal irradiance data set simulates hourly PV power output from roof-top installations, while a unit commitment and real-time economic dispatch (UC-ED) model simulates hourly system operations. We find that the large generating capacity of base-load nuclear power plants (NPPs) without ramping capability in the region limits PV integration levels to 5.3% (6510 MW) of 2015 generation. Enabling ramping capability for NPPs would raise the limit of PV penetration to near 9% of electricity generated. If the planned retirement of coal-fired power plants together with new installations and upgrades of natural gas and nuclear plants materialize in 2025, and if NPPs operate flexibly, then the share of coal-fired electricity will be reduced from 37% to 22%. A 9% penetration of electricity from PV would further reduce the share of coal-fired electricity by 4-6% resulting in a system-wide CO2 emissions rate of 0.33 to 0.40 tons/MWh and associated abatement costs of 225-415 (2015$ per ton).
Open Data in Global Environmental Research: The Belmont Forum's Open Data Survey.
Schmidt, Birgit; Gemeinholzer, Birgit; Treloar, Andrew
2016-01-01
This paper presents the findings of the Belmont Forum's survey on Open Data which targeted the global environmental research and data infrastructure community. It highlights users' perceptions of the term "open data", expectations of infrastructure functionalities, and barriers and enablers for the sharing of data. A wide range of good practice examples was pointed out by the respondents which demonstrates a substantial uptake of data sharing through e-infrastructures and a further need for enhancement and consolidation. Among all policy responses, funder policies seem to be the most important motivator. This supports the conclusion that stronger mandates will strengthen the case for data sharing.
Instructors as Investors: A Collegial Conspiracy To Improve Classroom Instruction.
ERIC Educational Resources Information Center
Lawson, Joan Kenny
Due to heavy teaching loads, high adjunct faculty numbers, and scheduling and commuting factors, community college faculty infrequently have the opportunity to share in a collegial forum. In an attempt to provide an opportunity for faculty to share innovative instructional strategies and discuss their work, Hudson Valley Community College (HVCC),…
Distributed control system for parallel-connected DC boost converters
Goldsmith, Steven
2017-08-15
The disclosed invention is a distributed control system for operating a DC bus fed by disparate DC power sources that service a known or unknown load. The voltage sources vary in v-i characteristics and have time-varying, maximum supply capacities. Each source is connected to the bus via a boost converter, which may have different dynamic characteristics and power transfer capacities, but are controlled through PWM. The invention tracks the time-varying power sources and apportions their power contribution while maintaining the DC bus voltage within the specifications. A central digital controller solves the steady-state system for the optimal duty cycle settings that achieve a desired power supply apportionment scheme for a known or predictable DC load. A distributed networked control system is derived from the central system that utilizes communications among controllers to compute a shared estimate of the unknown time-varying load through shared bus current measurements and bus voltage measurements.
Conditional load and store in a shared memory
Blumrich, Matthias A; Ohmacht, Martin
2015-02-03
A method, system and computer program product for implementing load-reserve and store-conditional instructions in a multi-processor computing system. The computing system includes a multitude of processor units and a shared memory cache, and each of the processor units has access to the memory cache. In one embodiment, the method comprises providing the memory cache with a series of reservation registers, and storing in these registers addresses reserved in the memory cache for the processor units as a result of issuing load-reserve requests. In this embodiment, when one of the processor units makes a request to store data in the memory cache using a store-conditional request, the reservation registers are checked to determine if an address in the memory cache is reserved for that processor unit. If an address in the memory cache is reserved for that processor, the data are stored at this address.
Parker, J W; Lane, J R; Karaikovic, E E; Gaines, R W
2000-05-01
A retrospective review of all the surgically managed spinal fractures at the University of Missouri Medical Center during the 41/2-year period from January 1989 to July 1993 was performed. Of the 51 surgically managed patients, 46 were instrumented by short-segment technique (attachment of one level above the fracture to one level below the fracture). The other 5 patients in this consecutive series had multiple trauma. These patients were included in the review because this was a consecutive series. However, they were grouped separately because they were instrumented by long-segment technique because of their multiple organ system injuries. The choice of the anterior or posterior approach for short-segment instrumentation was based on the Load-Sharing Classification published in a 1994 issue of Spine. The purpose of this review was to demonstrate that grading comminution by use of the Load-Sharing Classification for approach selection and the choice of patients with isolated fractures who are cooperative with spinal bracing for 4 months provide the keys to successful short-segment treatment of isolated spinal fractures. The current literature implies that the use of pedicle screws for short-segment instrumentation of spinal fracture is dangerous and inappropriate because of the high screw fracture rate. Charts, operative notes, preoperative and postoperative radiographs, computed tomography scans, and follow-up records of all patients were reviewed carefully from the time of surgery until final follow-up assessment. The Load-Sharing Classification had been used prospectively for all patients before their surgery to determine the approach for short-segment instrumentation. Denis' Pain Scale and Work Scales were obtained during follow-up evaluation for all patients. All patients were observed over 40 months except for 1 patient who died of unrelated causes after 35 months. The mean follow-up period was 66 months (51/2 years). No patient was lost to follow-up evaluation. Prospective application of the Load-Sharing Classification to the patients' injury and restriction of the short-segment approach to cooperative patients with isolated spinal fractures (excluding multisystem trauma patients) allowed 45 of 46 patients instrumented by the short-segment technique to proceed to successful healing in virtual anatomic alignment. The Load-Sharing Classification is a straightforward way to describe the amount of bony comminution in a spinal fracture. When applied to patients with isolated spine fractures who are cooperative with 3 to 4 months of spinal bracing, it can help the surgeon select short-segment pedicle-screw-based fixation using the posterior approach for less comminuted injuries and the anterior approach for those more comminuted. The choice of which fracture-dislocations should be strut grafted anteriorly and which need only posterior short-segment pedicle-screw-based instrumentation also can be made using the Load-Sharing Classification.
Empowering Faculty to Develop and Share Global Knowledge
ERIC Educational Resources Information Center
Harrison, David
2014-01-01
As colleges seek to increase global knowledge within its students, it is important that faculty members are also offered opportunities to increase their own knowledge of global issues. This chapter discusses faculty development models for seminars abroad and how these seminars encourage the development of unique global study programs.
Busch, G; Lammel, G; Beese, F O; Feichter, J; Dentener, F J; Roelofs, G J
2001-01-01
A global assessment of the impact of the anthropogenic perturbation of the nitrogen and sulfur cycles on forest ecosystems is carried out for both the present-day [1980-1990] and for a projection into the future [2040-2050] under a scenario of economic development which represents a medium path of development according to expert guess [IPCC IS92a]. Results show that forest soils will receive considerably increasing loads of nitrogen and acid deposition and that deposition patterns are likely to change. The regions which are most prone to depletion of soils buffering capacity and supercritical nitrogen deposition are identified in the subtropical and tropical regions of South America and Southeast Asia apart from the well known 'hotspots' North-Eastern America and Central Europe. The forest areas likely to meet these two risks are still a minor fraction of the global forest ecosystems, though. But the bias between eutrophication and acidification will become greater and an enhanced growth triggered by the fertilizing effects of increasing nitrogen input cannot be balanced by the forest soils nutrient pools. Results show increasing loads into forest ecosystems which are likely to account for 46% higher acid loads and 36% higher nitrogen loads in relation to the 1980-1990 situation. Global background deposition of up to 5 kg N ha-1 a-1 will be exceeded at more than 25% of global forest ecosystems and at more than 50% of forest ecosystems on acid sensitive soils. More than 33% of forest ecosystems on acid sensitive soils will receive acid loads which exceeds their buffering capacity. About 25% of forest areas with exceeded acid loads will receive critical nitrogen loads.
NASA Technical Reports Server (NTRS)
Klimas, A. J.; Uritsky, V.; Vassiliadis, D.; Baker, D. N.
2005-01-01
Loading and consequent unloading of magnetic flux is an essential element of the substorm cycle in Earth's magnetotail. We are unaware of an available global MHD magnetospheric simulation model that includes a loading- unloading cycle in its behavior. Given the central role that MHD models presently play in the development of our understanding of magnetospheric dynamics, and given the present plans for the central role that these models will play in ongoing space weather prediction programs, it is clear that this failure must be corrected. A 2-dimensional numerical driven current-sheet model has been developed that incorporates an idealized current- driven instability with a resistive MHD system. Under steady loading, the model exhibits a global loading- unloading cycle. The specific mechanism for producing the loading-unloading cycle will be discussed. It will be shown that scale-free avalanching of electromagnetic energy through the model, from loading to unloading, is carried by repetitive bursts of localized reconnection. Each burst leads, somewhat later, to a field configuration that is capable of exciting a reconnection burst again. This process repeats itself in an intermittent manner while the total field energy in the system falls. At the end of an unloading interval, the total field energy is reduced to well below that necessary to initiate the next unloading event and, thus, a loading-unloading cycle results. It will be shown that, in this model, it is the topology of bursty localized reconnection that is responsible for the appearance of the loading-unloading cycle.
Federal Register 2010, 2011, 2012, 2013, 2014
2011-09-01
... (GAC) to discuss the Global Initiative, as described at http://www.it.ojp.gov/global . DATES: [email protected]gov . SUPPLEMENTARY INFORMATION: This meeting is open to the public. Due to security measures...
Federal Register 2010, 2011, 2012, 2013, 2014
2010-09-16
... Committee (GAC) to discuss the Global Initiative, as described at http://www.it.ojp.gov/global . DATES: [email protected]gov . SUPPLEMENTARY INFORMATION: This meeting is open to the public. Due to security measures...
Measuring cognitive load during procedural skills training with colonoscopy as an exemplar.
Sewell, Justin L; Boscardin, Christy K; Young, John Q; Ten Cate, Olle; O'Sullivan, Patricia S
2016-06-01
Few studies have investigated cognitive factors affecting learning of procedural skills in medical education. Cognitive load theory, which focuses on working memory, is highly relevant, but methods for measuring cognitive load during procedural training are not well understood. Using colonoscopy as an exemplar, we used cognitive load theory to develop a self-report instrument to measure three types of cognitive load (intrinsic, extraneous and germane load) and to provide evidence for instrument validity. We developed the instrument (the Cognitive Load Inventory for Colonoscopy [CLIC]) using a multi-step process. It included 19 items measuring three types of cognitive load, three global rating items and demographics. We then conducted a cross-sectional survey that was administered electronically to 1061 gastroenterology trainees in the USA. Participants completed the CLIC following a colonoscopy. The two study phases (exploratory and confirmatory) each lasted for 10 weeks during the 2014-2015 academic year. Exploratory factor analysis determined the most parsimonious factor structure; confirmatory factor analysis assessed model fit. Composite measures of intrinsic, extraneous and germane load were compared across years of training and with global rating items. A total of 477 (45.0%) invitees participated (116 in the exploratory study and 361 in the confirmatory study) in 154 (95.1%) training programmes. Demographics were similar to national data from the USA. The most parsimonious factor structure included three factors reflecting the three types of cognitive load. Confirmatory factor analysis verified that a three-factor model was the best fit. Intrinsic, extraneous and germane load items had high internal consistency (Cronbach's alpha 0.90, 0.87 and 0.96, respectively) and correlated as expected with year in training and global assessment of cognitive load. The CLIC measures three types of cognitive load during colonoscopy training. Evidence of validity is provided. Although CLIC items relate to colonoscopy, the development process we detail can be used to adapt the instrument for use in other learning settings in medical education. © 2016 John Wiley & Sons Ltd.
Federal Register 2010, 2011, 2012, 2013, 2014
2013-11-06
... shares traded. Specifically, the Exchange states that, according to State Street Global Advisor, the... to the Exchange, for the three months ending on June 20, 2013, the average daily volume in SPY shares was 137 million, and the average value of shares traded was $22.1 billion. According to the Exchange...
Nurse manager perspective of staff participation in unit level shared governance.
Cox Sullivan, Sheila; Norris, Mitzi R; Brown, Lana M; Scott, Karen J
2017-11-01
To examine the nurse manager perspective surrounding implementation of unit level shared governance in one Veterans Health Administration facility. Nursing shared governance is a formal model allowing nursing staff decision-making input into clinical practice, quality improvement, evidence-based practice and staff professional development. Unit level shared governance is a management process where decision authority is delegated to nursing staff at the unit level. Convenience sampling was used to recruit ten nurse managers who participated in face-to-face semi-structured interviews. Data were analysed using content analysis and constant comparison techniques. Demographic data were described using descriptive statistics. The participants included seven female and three male nurse managers with seven Caucasian and three African American. Participant quotes were clustered to identify sub-themes that were then grouped into four global themes to describe unit level shared governance. The global themes were: (1) motivation, (2) demotivation, (3) recommendations for success, and (4) outcomes. These research findings resonate with previous studies that shared governance may be associated with increased nurse empowerment, self-management, engagement, and satisfaction. These findings reflect the need for nurse managers to promote and recognize staff participation in unit level shared governance. © 2017 John Wiley & Sons Ltd.
Nõges, T; Laugaste, R; Loigu, E; Nedogarko, I; Skakalski, B; Nõges, P
2005-01-01
Lake Peipsi (3555 km2, mean depth 7.1 m) located on the border of Estonia and Russia is the largest transboundary lake in Europe. L. Peipsi consists of three parts. The shared largest northern part L. Peipsi s.s. (2611 km2, 8.3 m) and the southern L. Pihkva (708 km2, 3.8 m) which belongs mainly to Russia are connected by the river-shaped L. Lämmijärv (236 km2, 2.5 m). The catchment area (44,245 km2 without lake area) is shared between Estonia (33.3%), Russia (58.6%) and Latvia (8%). Intensive eutrophication of L. Peipsi started in the 1970s. The biomass of N2-fixing cyanobacteria was low at heavy nutrient loading in the 1980s. After the collapse of soviet-type agriculture in the early 1990s, the loading of nitrogen sharply decreased. A certain improvement of L. Peipsi s.s. was noticed at the beginning of the 1990s together with the temporary reduction of phosphorus loading from Estonian catchment while in recent years a destabilisation of the ecosystem has been observed. This deterioration has been expressed mainly as intensive blue-green blooms and fish-kills in summer. Reappearance of blooms has been explained by the decrease in N/P loading ratio due to reduced N discharge while in some periods increased phosphorus loading could have supported this trend.
ERIC Educational Resources Information Center
Byker, Erik Jon; Marquardt, Sheila K.
2016-01-01
Globally-minded teachers often beget globally-minded students. The same relationship seems to hold true for multiculturalism; teachers who are committed to multiculturalism often nudge students toward the same commitment. Global citizenship and multicultural education share a strong bond. Yet, in the field of social studies teacher preparation,…
Hidden concerns of sharing research data by low/middle-income country scientists.
Bezuidenhout, Louise; Chakauya, Ereck
2018-01-01
There has considerable interest in bringing low/middle-income countries (LMIC) scientists into discussions on Open Data - both as contributors and users. The establishment of in situ data sharing practices within LMIC research institutions is vital for the development of an Open Data landscape in the Global South. Nonetheless, many LMICs have significant challenges - resource provision, research support and extra-laboratory infrastructures. These low-resourced environments shape data sharing activities, but are rarely examined within Open Data discourse. In particular, little attention is given to how these research environments shape scientists' perceptions of data sharing (dis)incentives. This paper expands on these issues of incentivizing data sharing, using data from a quantitative survey disseminated to life scientists in 13 countries in sub-Saharan Africa. This interrogated not only perceptions of data sharing amongst LMIC scientists, but also how these are connected to the research environments and daily challenges experienced by them. The paper offers a series of analysis around commonly cited (dis)incentives such as data sharing as a means of improving research visibility; sharing and funding; and online connectivity. It identifies key areas that the Open Data community need to consider if true openness in research is to be established in the Global South.
NASA Astrophysics Data System (ADS)
Cohen, S.; Alfieri, L.; Brakenridge, G. R.; Coughlan, E.; Galantowicz, J. F.; Hong, Y.; Kettner, A.; Nghiem, S. V.; Prados, A. I.; Rudari, R.; Salamon, P.; Trigg, M.; Weerts, A.
2017-12-01
The Global Flood Partnership (GFP; https://gfp.jrc.ec.europa.eu) is a multi-disciplinary group of scientists, operational agencies and flood risk managers focused on developing efficient and effective global flood management tools. Launched in 2014, its aim is to establish a partnership for global flood forecasting, monitoring and impact assessment to strengthen preparedness and response and to reduce global disaster losses. International organizations, the private sector, national authorities, universities and research agencies contribute to the GFP on a voluntary basis and benefit from a global network focused on flood risk reduction. At the onset of Hurricane Harvey, GFP was `activated' using email requests via its mailing service. Soon after, flood inundation maps, based on remote sensing analysis and modeling, were shared by different agencies, institutions, and individuals. These products were disseminated, to varying degrees of effectiveness, to federal, state and local agencies via emails and data-sharing services. This generated a broad data-sharing network which was utilized at the early stages of Hurricane Irma's impact, just two weeks after Harvey. In this presentation, we will describe the extent and chronology of the GFP response to both Hurricanes Harvey, Irma and Maria. We will assess the potential usefulness of this effort for event managers in various types of organizations and discuss future improvements to be implemented.
Self-aligning hydraulic piston assembly for tensile testing of ceramic
Liu, Kenneth C.
1987-01-01
The present invention is directed to a self-aligning grip housing assembly that can transmit an uniaxial load to a tensil specimen without introducing bending stresses into the specimen. Disposed inside said grip housing assembly are a multiplicity of supporting pistons connected to a common source of pressurized oil that carry equal shares of the load applied to the specimen irregardless whether there is initial misalignment between the specimen load column assembly and housing axis.
Self-aligning hydraulic piston assembly for tensile testing of ceramic
Liu, K.C.
1987-08-18
The present invention is directed to a self-aligning grip housing assembly that can transmit an uniaxial load to a tensile specimen without introducing bending stresses into the specimen. Disposed inside said grip housing assembly are a multiplicity of supporting pistons connected to a common source of pressurized oil that carry equal shares of the load applied to the specimen regardless whether there is initial misalignment between the specimen load column assembly and housing axis. 4 figs.
ERIC Educational Resources Information Center
Winchester-Seeto, Theresa; Rowe, Anna; Mackaway, Jacqueline
2016-01-01
Student supervision is a key factor underpinning the success of work-integrated learning programs. Supervisory responsibilities can be shared across a number of stakeholders including university staff and host/workplace supervisors. While there have been attempts to understand the roles played by each of these stakeholders, little research has…
Dynamic Transfers Of Tasks Among Computers
NASA Technical Reports Server (NTRS)
Liu, Howard T.; Silvester, John A.
1989-01-01
Allocation scheme gives jobs to idle computers. Ideal resource-sharing algorithm should have following characteristics: Dynamics, decentralized, and heterogeneous. Proposed enhanced receiver-initiated dynamic algorithm (ERIDA) for resource sharing fulfills all above criteria. Provides method balancing workload among hosts, resulting in improvement in response time and throughput performance of total system. Adjusts dynamically to traffic load of each station.
Layton, Natasha; Murphy, Caitlin; Bell, Diane
2018-07-01
Assistive technology (AT) is an essential facilitator of independence and participation, both for people living with the effects of disability and/or non-communicable disease, as well as people aging with resultant functional decline. The World Health Organization (WHO) recognizes the substantial gap between the need for and provision of AT and is leading change through the Global Cooperation on Assistive Technology (GATE) initiative. Showcasing innovations gathered from 92 global researchers, innovators, users and educators of AT through the WHO GREAT Summit, this article provides an analysis of ideas and actions on a range of dimensions in order to provide a global overview of AT innovation. The accessible method used to capture and showcase this data is presented and critiqued, concluding that "innovation snapshots" are a rapid and concise strategy to capture and showcase AT innovation and to foster global collaboration. Implications for Rehabilitation Focal tools such as ePosters with uniform data requirements enable the rapid sharing of information. A diversity of innovative practices are occurring globally in the areas of AT Products, Policy, Provision, People and Personnel. The method offered for Innovation Snapshots had substantial uptake and is a feasible means to capture data across a range of stakeholders. Meeting accessibility criteria is an emerging competency in the AT community. Substantial areas of common interest exist across regions and globally in the AT community, demonstrating the effectiveness of information sharing platforms such as GATE and supporting the idea of regional forums and networks.
PNNL’s Shared Perspectives Technology
DOE Office of Scientific and Technical Information (OSTI.GOV)
None
2015-09-25
Shared Perspectives, one of the technologies within the PNNL-developed GridOPTICS capability suite, enables neighboring organizations, such as different electric utilities, to more effectively partner to solve outages and other grid problems. Shared Perspectives provides a means for organizations to safely stream information from different organizational service areas; the technology then combines and aligns this information into a common, global view, enhancing global situation awareness that can reduce the time it takes to talk through a problem and identify solutions. The technology potentially offers applications in other areas, such as disaster response; collaboration in the monitoring/assessment of real-time events (e.g., hurricanes,more » earthquakes, and tornadoes); as well as military uses.« less
PNNLâs Shared Perspectives Technology
None
2018-01-16
Shared Perspectives, one of the technologies within the PNNL-developed GridOPTICS capability suite, enables neighboring organizations, such as different electric utilities, to more effectively partner to solve outages and other grid problems. Shared Perspectives provides a means for organizations to safely stream information from different organizational service areas; the technology then combines and aligns this information into a common, global view, enhancing global situation awareness that can reduce the time it takes to talk through a problem and identify solutions. The technology potentially offers applications in other areas, such as disaster response; collaboration in the monitoring/assessment of real-time events (e.g., hurricanes, earthquakes, and tornadoes); as well as military uses.
Open Data in Global Environmental Research: The Belmont Forum’s Open Data Survey
Schmidt, Birgit; Gemeinholzer, Birgit; Treloar, Andrew
2016-01-01
This paper presents the findings of the Belmont Forum’s survey on Open Data which targeted the global environmental research and data infrastructure community. It highlights users’ perceptions of the term “open data”, expectations of infrastructure functionalities, and barriers and enablers for the sharing of data. A wide range of good practice examples was pointed out by the respondents which demonstrates a substantial uptake of data sharing through e-infrastructures and a further need for enhancement and consolidation. Among all policy responses, funder policies seem to be the most important motivator. This supports the conclusion that stronger mandates will strengthen the case for data sharing. PMID:26771577
NASA Astrophysics Data System (ADS)
Levi, Lea; Cvetkovic, Vladimir; Destouni, Georgia
2015-04-01
This study compiles estimates of total nitrogen and phosphorus loads in the Sava River Catchment (SRC), investigates the load relations to human drivers of excess nutrient loading, and compares them with corresponding relations implied by data reported for the Baltic region. Nutrient load data, associated average discharge concentrations (ratio of load to water discharge) and their relations to human drivers are investigated across subcatchments of the SRC with different agricultural and population conditions. The Zagreb subcatchment, which has the smallest area but the highest population density and runoff among the investigated SRC subcatchments, exhibits the highest loads of both nitrogen and phosphorus. Overall for the SRC, results show high correlation (R2=0.93-0.95) of nutrient loads with population density and of concentrations with farmland share. A further question investigated here is then to what degree these relations are comparable with such relations found also for the Baltic region. The two regions are otherwise quite different in their climatic, agricultural and wastewater treatment conditions, so relation consistency, even if surprising, would be important in indicating some degree of relation transferability worthy of further investigation also in other regions. For the Baltic region corresponding correlations to those found in the SRC are in the range R2=0.79-0.88. In particular nitrogen and phosphorus concentration correlations with farmland share are qualitatively consistent between the regions. At the same time, phosphorus concentration correlation with population density shows quite different results between regions. Obtained results indicate a certain level of transferability of dependencies between the two regions and call for further detailed investigations on finer spatial-temporal scales.
Research on virtual network load balancing based on OpenFlow
NASA Astrophysics Data System (ADS)
Peng, Rong; Ding, Lei
2017-08-01
The Network based on OpenFlow technology separate the control module and data forwarding module. Global deployment of load balancing strategy through network view of control plane is fast and of high efficiency. This paper proposes a Weighted Round-Robin Scheduling algorithm for virtual network and a load balancing plan for server load based on OpenFlow. Load of service nodes and load balancing tasks distribution algorithm will be taken into account.
NASA Technical Reports Server (NTRS)
Estes, R. H.
1977-01-01
A computer software system is described which computes global numerical solutions of the integro-differential Laplace tidal equations, including dissipation terms and ocean loading and self-gravitation effects, for arbitrary diurnal and semidiurnal tidal constituents. The integration algorithm features a successive approximation scheme for the integro-differential system, with time stepping forward differences in the time variable and central differences in spatial variables. Solutions for M2, S2, N2, K2, K1, O1, P1 tidal constituents neglecting the effects of ocean loading and self-gravitation and a converged M2, solution including ocean loading and self-gravitation effects are presented in the form of cotidal and corange maps.
Android Protection Mechanism: A Signed Code Security Mechanism for Smartphone Applications
2011-03-01
status registers, exceptions, endian support, unaligned access support, synchronization primitives , the Jazelle Extension, and saturated integer...supports comprehensive non-blocking shared-memory synchronization primitives that scale for multiple-processor system designs. This is an improvement... synchronization . Memory semaphores can be loaded and altered without interruption because the load and store operations are atomic. Processor
When Going Global Isn't Enough.
ERIC Educational Resources Information Center
Randolph, Benton
1990-01-01
The traditional multinational approach to business strategy and human resource management, as well as the global approach, are not effective in a world no longer insular. A transnational approach requires global strategy and perspective, local responsiveness and flexibility, teamwork, shared responsibility, and empowered and innovative workers.…
Impact of overweight vehicles (with heavy axle loads) on bridge deck deterioration.
DOT National Transportation Integrated Search
2012-03-01
Bridge deck slabs develop compressive stresses from global flexural deformation and locally from high-level : wheel loads when it is subjected to overweight trucks. This study quantified the impact of overweight vehicles : with heavy axle loads on br...
Flight motor set 360L001 (STS-26R). (Reconstructed dynamic loads analysis)
NASA Technical Reports Server (NTRS)
Call, V. B.
1989-01-01
A transient analysis was performed to correlate the predicted versus measured behavior of the Redesigned Solid Rocket Booster (RSRB) during Flight 360L001 (STS-26R) liftoff. Approximately 9 accelerometers, 152 strain gages, and 104 girth gages were bonded to the motors during this event. Prior to Flight 360L001, a finite element model of the RSRB was analyzed to predict the accelerations, strains, and displacements measured by this developmental flight instrumentation (DFI) within an order of magnitude. Subsequently, an analysis has been performed which uses actual Flight 360L001 liftoff loading conditions, and makes more precise predictions for the RSRB structural behavior. Essential information describing the analytical model, analytical techniques used, correlation of the predicted versus measured RSRB behavior, and conclusions, are presented. A detailed model of the RSRB was developed and correlated for use in analyzing the motor behavior during liftoff loading conditions. This finite element model, referred to as the RSRB global model, uses super-element techniques to model all components of the RSRB. The objective of the RSRB global model is to accurately predict deflections and gap openings in the field joints to an accuracy of approximately 0.001 inch. The model of the field joint component was correlated to Referee and Joint Environment Simulation (JES) tests. The accuracy of the assembled RSRB global model was validated by correlation to static-fire tests such DM-8, DM-9, QM-7, and QM-8. This validated RSRB global model was used to predict RSRB structural behavior and joint gap opening during Flight 360L001 liftoff. The results of a transient analysis of the RSRB global model with imposed liftoff loading conditions are presented. Rockwell used many gage measurements to reconstruct the load parameters which were imposed on the RSRB during the Flight 360L001 liftoff. Each load parameter, and its application, is described. Also presented are conclusions and recommendations based on the analysis of this load case and the resulting correlation between predicted and measured RSRB structural behavior.
Johnson, Micah A.; Diaz, Michele T.; Madden, David J.
2014-01-01
Although age-related differences in white matter have been well documented, the degree to which regional, tract-specific effects can be distinguished from global, brain-general effects is not yet clear. Similarly, the manner in which global and regional differences in white matter integrity contribute to age-related differences in cognition has not been well established. To address these issues, we analyzed diffusion tensor imaging measures from 52 younger adults (18–28) and 64 older adults (60–85). We conducted principal component analysis on each diffusion measure, using data from eight individual tracts. Two components were observed for fractional anisotropy: The first comprised high loadings from the superior longitudinal fasciculi and corticospinal tracts, and the second comprised high loadings from the optic radiations. In contrast, variation in axial, radial, and mean diffusivities yielded a single-component solution in each case, with high loadings from most or all tracts. For fractional anisotropy, the complementary results of multiple components and variability in component loadings across tracts suggest regional variation. However, for the diffusivity indices, the single component with high loadings from most or all of the tracts suggests primarily global, brain-general variation. Further analyses indicated that age was a significant mediator of the relation between each component and perceptual-motor speed. These data suggest that individual differences in white matter integrity, and their relation to age-related differences in perceptual-motor speed, represent influences that are beyond the level of individual tracts, but the extent to which regional or global effects predominate may differ between anisotropy and diffusivity measures. PMID:24972959
Global Access-controlled Transfer e-frame (GATe)
DOE Office of Scientific and Technical Information (OSTI.GOV)
2012-05-30
Global Access-controlled Transfer e-frame (GATe) was designed to take advantage of the patterns that occur during an electronic record transfer process. The e-frame (or electronic framework or platform) is the foundation for developing secure information transfer to meet classified and unclassified business processes and is particularly useful when there is a need to share information with various entities in a controlled and secure environment. It can share, search, upload, download and retrieve sensitive information, as well as provides reporting capabilities.
Energy, variability and weather finance engineering
NASA Astrophysics Data System (ADS)
Roussis, Dimitrios; Parara, Iliana; Gournari, Panagiota; Moustakis, Yiannis; Dimitriadis, Panayiotis; Iliopoulou, Theano; Koutsoyiannis, Demetris; Karakatsanis, Georgios
2017-04-01
Most types of renewable energies are characterized by intense intermittency, causing significant instabilities to the grid; further requiring additional infrastructure (e.g. pumped-storage) for buffering hydrometeorological uncertainties, as well as complex operational rules for load balancing. In addition, most intermittent renewable units are subsidized, creating significant market inefficiencies. Weather derivatives comprise mature financial tools for integrating successfully the intermittent-load and base-load components into a unified hybrid energy system and establish their operation within a generalized uncertainty management market. With a growing global market share and 46% utilization of this financial tool by the energy industry and 12% by agriculture (that partially concerns biofuel resources), weather derivatives are projected to constitute a critical subsystem of many grids for buffering frequent hydrometeorological risks of low and medium impacts -which are not covered by standard insurance contracts that aim exclusively at extreme events and high financial damages. In this context, we study the attributes of hydrometeorological time series in a remote and small island in Greece, powered by an autonomous hybrid energy system. Upon the results we choose the optimal underlying index and we further compose and engineer a weather derivative with features of a typical option contract -which we consider most flexible and appropriate for the case- to test our assumptions on its beneficiary effects for both the budget of private energy producers and the island's public administration. Acknowledgement: This research is conducted within the frame of the undergraduate course "Stochastic Methods in Water Resources" of the National Technical University of Athens (NTUA). The School of Civil Engineering of NTUA provided moral support for the participation of the students in the Assembly.
NASA Astrophysics Data System (ADS)
Malsy, Marcus; Reder, Klara; Flörke, Martina
2014-05-01
Decreasing water quality is one of the main global issues which poses risks to food security, economy, and public health and is consequently crucial for ensuring environmental sustainability. During the last decades access to clean drinking water increased, but 2.5 billion people still do not have access to basic sanitation, especially in Africa and parts of Asia. In this context not only connection to sewage system is of high importance, but also treatment, as an increasing connection rate will lead to higher loadings and therefore higher pressure on water resources. Furthermore, poor people in developing countries use local surface waters for daily activities, e.g. bathing and washing. It is thus clear that water utilization and water sewerage are indispensable connected. In this study, large scale water quality modelling is used to point out hotspots of water pollution to get an insight on potential environmental impacts, in particular, in regions with a low observation density and data gaps in measured water quality parameters. We applied the global water quality model WorldQual to calculate biological oxygen demand (BOD) loadings from point and diffuse sources, as well as in-stream concentrations. Regional focus in this study is on developing countries i.e. Africa, Asia, and South America, as they are most affected by water pollution. Hereby, model runs were conducted for the year 2010 to draw a picture of recent status of surface waters quality and to figure out hotspots and main causes of pollution. First results show that hotspots mainly occur in highly agglomerated regions where population density is high. Large urban areas are initially loading hotspots and pollution prevention and control become increasingly important as point sources are subject to connection rates and treatment levels. Furthermore, river discharge plays a crucial role due to dilution potential, especially in terms of seasonal variability. Highly varying shares of BOD sources across regions, and across sectors demand for an integrated approach to assess main causes of water quality degradation.
Wang, Mingxun; Carver, Jeremy J; Phelan, Vanessa V; Sanchez, Laura M; Garg, Neha; Peng, Yao; Nguyen, Don Duy; Watrous, Jeramie; Kapono, Clifford A; Luzzatto-Knaan, Tal; Porto, Carla; Bouslimani, Amina; Melnik, Alexey V; Meehan, Michael J; Liu, Wei-Ting; Crüsemann, Max; Boudreau, Paul D; Esquenazi, Eduardo; Sandoval-Calderón, Mario; Kersten, Roland D; Pace, Laura A; Quinn, Robert A; Duncan, Katherine R; Hsu, Cheng-Chih; Floros, Dimitrios J; Gavilan, Ronnie G; Kleigrewe, Karin; Northen, Trent; Dutton, Rachel J; Parrot, Delphine; Carlson, Erin E; Aigle, Bertrand; Michelsen, Charlotte F; Jelsbak, Lars; Sohlenkamp, Christian; Pevzner, Pavel; Edlund, Anna; McLean, Jeffrey; Piel, Jörn; Murphy, Brian T; Gerwick, Lena; Liaw, Chih-Chuang; Yang, Yu-Liang; Humpf, Hans-Ulrich; Maansson, Maria; Keyzers, Robert A; Sims, Amy C; Johnson, Andrew R; Sidebottom, Ashley M; Sedio, Brian E; Klitgaard, Andreas; Larson, Charles B; P, Cristopher A Boya; Torres-Mendoza, Daniel; Gonzalez, David J; Silva, Denise B; Marques, Lucas M; Demarque, Daniel P; Pociute, Egle; O'Neill, Ellis C; Briand, Enora; Helfrich, Eric J N; Granatosky, Eve A; Glukhov, Evgenia; Ryffel, Florian; Houson, Hailey; Mohimani, Hosein; Kharbush, Jenan J; Zeng, Yi; Vorholt, Julia A; Kurita, Kenji L; Charusanti, Pep; McPhail, Kerry L; Nielsen, Kristian Fog; Vuong, Lisa; Elfeki, Maryam; Traxler, Matthew F; Engene, Niclas; Koyama, Nobuhiro; Vining, Oliver B; Baric, Ralph; Silva, Ricardo R; Mascuch, Samantha J; Tomasi, Sophie; Jenkins, Stefan; Macherla, Venkat; Hoffman, Thomas; Agarwal, Vinayak; Williams, Philip G; Dai, Jingqui; Neupane, Ram; Gurr, Joshua; Rodríguez, Andrés M C; Lamsa, Anne; Zhang, Chen; Dorrestein, Kathleen; Duggan, Brendan M; Almaliti, Jehad; Allard, Pierre-Marie; Phapale, Prasad; Nothias, Louis-Felix; Alexandrov, Theodore; Litaudon, Marc; Wolfender, Jean-Luc; Kyle, Jennifer E; Metz, Thomas O; Peryea, Tyler; Nguyen, Dac-Trung; VanLeer, Danielle; Shinn, Paul; Jadhav, Ajit; Müller, Rolf; Waters, Katrina M; Shi, Wenyuan; Liu, Xueting; Zhang, Lixin; Knight, Rob; Jensen, Paul R; Palsson, Bernhard O; Pogliano, Kit; Linington, Roger G; Gutiérrez, Marcelino; Lopes, Norberto P; Gerwick, William H; Moore, Bradley S; Dorrestein, Pieter C; Bandeira, Nuno
2016-08-09
The potential of the diverse chemistries present in natural products (NP) for biotechnology and medicine remains untapped because NP databases are not searchable with raw data and the NP community has no way to share data other than in published papers. Although mass spectrometry (MS) techniques are well-suited to high-throughput characterization of NP, there is a pressing need for an infrastructure to enable sharing and curation of data. We present Global Natural Products Social Molecular Networking (GNPS; http://gnps.ucsd.edu), an open-access knowledge base for community-wide organization and sharing of raw, processed or identified tandem mass (MS/MS) spectrometry data. In GNPS, crowdsourced curation of freely available community-wide reference MS libraries will underpin improved annotations. Data-driven social-networking should facilitate identification of spectra and foster collaborations. We also introduce the concept of 'living data' through continuous reanalysis of deposited data.
Structural Analysis for the American Airlines Flight 587 Accident Investigation: Global Analysis
NASA Technical Reports Server (NTRS)
Young, Richard D.; Lovejoy, Andrew E.; Hilburger, Mark W.; Moore, David F.
2005-01-01
NASA Langley Research Center (LaRC) supported the National Transportation Safety Board (NTSB) in the American Airlines Flight 587 accident investigation due to LaRC's expertise in high-fidelity structural analysis and testing of composite structures and materials. A Global Analysis Team from LaRC reviewed the manufacturer s design and certification procedures, developed finite element models and conducted structural analyses, and participated jointly with the NTSB and Airbus in subcomponent tests conducted at Airbus in Hamburg, Germany. The Global Analysis Team identified no significant or obvious deficiencies in the Airbus certification and design methods. Analysis results from the LaRC team indicated that the most-likely failure scenario was failure initiation at the right rear main attachment fitting (lug), followed by an unstable progression of failure of all fin-to-fuselage attachments and separation of the VTP from the aircraft. Additionally, analysis results indicated that failure initiates at the final observed maximum fin loading condition in the accident, when the VTP was subjected to loads that were at minimum 1.92 times the design limit load condition for certification. For certification, the VTP is only required to support loads of 1.5 times design limit load without catastrophic failure. The maximum loading during the accident was shown to significantly exceed the certification requirement. Thus, the structure appeared to perform in a manner consistent with its design and certification, and failure is attributed to VTP loads greater than expected.
Combining Distributed and Shared Memory Models: Approach and Evolution of the Global Arrays Toolkit
DOE Office of Scientific and Technical Information (OSTI.GOV)
Nieplocha, Jarek; Harrison, Robert J.; Kumar, Mukul
2002-07-29
Both shared memory and distributed memory models have advantages and shortcomings. Shared memory model is much easier to use but it ignores data locality/placement. Given the hierarchical nature of the memory subsystems in the modern computers this characteristic might have a negative impact on performance and scalability. Various techniques, such as code restructuring to increase data reuse and introducing blocking in data accesses, can address the problem and yield performance competitive with message passing[Singh], however at the cost of compromising the ease of use feature. Distributed memory models such as message passing or one-sided communication offer performance and scalability butmore » they compromise the ease-of-use. In this context, the message-passing model is sometimes referred to as?assembly programming for the scientific computing?. The Global Arrays toolkit[GA1, GA2] attempts to offer the best features of both models. It implements a shared-memory programming model in which data locality is managed explicitly by the programmer. This management is achieved by explicit calls to functions that transfer data between a global address space (a distributed array) and local storage. In this respect, the GA model has similarities to the distributed shared-memory models that provide an explicit acquire/release protocol. However, the GA model acknowledges that remote data is slower to access than local data and allows data locality to be explicitly specified and hence managed. The GA model exposes to the programmer the hierarchical memory of modern high-performance computer systems, and by recognizing the communication overhead for remote data transfer, it promotes data reuse and locality of reference. This paper describes the characteristics of the Global Arrays programming model, capabilities of the toolkit, and discusses its evolution.« less
Potential for shared log transport services
Tim McDonald; Steve Taylor; Jorge Valenzuela
2001-01-01
A simulation model of a log transport logistics network was developed. The model could be structured to either share truck capacity among a group of loggers, or to assign a fixed number of trucks to individual loggers. Another variation of the model allowed the use of a staging yard to set out loaded trailers and deliver them to destinations using dedicated shuttle...
ERIC Educational Resources Information Center
New England Board of Higher Education, Wellesley, MA. New England Library Information Network.
The potential for using a computerized communication system to facilitate resource sharing in New England has been investigated by the staff of the New England Information Network (NELINET). The central purpose of their research was to determine whether a strategy for load leveling of interlibrary loan (ILL) requests could be implemented online as…
Modelling of Fiber/Matrix Debonding of Composites Under Cyclic Loading
NASA Technical Reports Server (NTRS)
Naghipour, Paria; Pineda, Evan J.; Bednarcyk, Brett A.; Arnold, Steven M.
2013-01-01
The micromechanics theory, generalized method of cells (GMC), was employed to simulate the debonding of fiber/matrix interfaces, within a repeating unit cell subjected to global, cyclic loading, utilizing a cyclic crack growth law. Cycle dependent, interfacial debonding was implemented as a new module to the available GMC formulation. The degradation of interfacial stresses, with applied load cycles, was achieved via progressive evolution of the interfacial compliance. A periodic repeating unit cell, representing the fiber/matrix architecture of a composite, was subjected to combined normal and shear loadings, and degradation of the global transverse stress in successive cycles was monitored. The obtained results were compared to values from a corresponding finite element model. Reasonable agreement was achieved for combined normal and shear loading conditions, with minimal variation for pure loading cases. The local effects of interfacial debonding, and fatigue damage will later be combined as sub-models to predict the experimentally obtained fatigue life of Ti-15-3/Sic composites at the laminate level.
Atmospheric pressure loading effects on Global Positioning System coordinate determinations
NASA Technical Reports Server (NTRS)
Vandam, Tonie M.; Blewitt, Geoffrey; Heflin, Michael B.
1994-01-01
Earth deformation signals caused by atmospheric pressure loading are detected in vertical position estimates at Global Positioning System (GPS) stations. Surface displacements due to changes in atmospheric pressure account for up to 24% of the total variance in the GPS height estimates. The detected loading signals are larger at higher latitudes where pressure variations are greatest; the largest effect is observed at Fairbanks, Alaska (latitude 65 deg), with a signal root mean square (RMS) of 5 mm. Out of 19 continuously operating GPS sites (with a mean of 281 daily solutions per site), 18 show a positive correlation between the GPS vertical estimates and the modeled loading displacements. Accounting for loading reduces the variance of the vertical station positions on 12 of the 19 sites investigated. Removing the modeled pressure loading from GPS determinations of baseline length for baselines longer than 6000 km reduces the variance on 73 of the 117 baselines investigated. The slight increase in variance for some of the sites and baselines is consistent with expected statistical fluctuations. The results from most stations are consistent with approximately 65% of the modeled pressure load being found in the GPS vertical position measurements. Removing an annual signal from both the measured heights and the modeled load time series leaves this value unchanged. The source of the remaining discrepancy between the modeled and observed loading signal may be the result of (1) anisotropic effects in the Earth's loading response, (2) errors in GPS estimates of tropospheric delay, (3) errors in the surface pressure data, or (4) annual signals in the time series of loading and station heights. In addition, we find that using site dependent coefficients, determined by fitting local pressure to the modeled radial displacements, reduces the variance of the measured station heights as well as or better than using the global convolution sum.
Global Load Balancing with Parallel Mesh Adaption on Distributed-Memory Systems
NASA Technical Reports Server (NTRS)
Biswas, Rupak; Oliker, Leonid; Sohn, Andrew
1996-01-01
Dynamic mesh adaption on unstructured grids is a powerful tool for efficiently computing unsteady problems to resolve solution features of interest. Unfortunately, this causes load imbalance among processors on a parallel machine. This paper describes the parallel implementation of a tetrahedral mesh adaption scheme and a new global load balancing method. A heuristic remapping algorithm is presented that assigns partitions to processors such that the redistribution cost is minimized. Results indicate that the parallel performance of the mesh adaption code depends on the nature of the adaption region and show a 35.5X speedup on 64 processors of an SP2 when 35% of the mesh is randomly adapted. For large-scale scientific computations, our load balancing strategy gives almost a sixfold reduction in solver execution times over non-balanced loads. Furthermore, our heuristic remapper yields processor assignments that are less than 3% off the optimal solutions but requires only 1% of the computational time.
Stern, RJ; Fernandez, A; Jacobs, EA; Neilands, TB; Weech-Maldonado, R; Quan, J; Carle, A; Seligman, HK
2012-01-01
Background Providing culturally competent care shows promise as a mechanism to reduce healthcare inequalities. Until the recent development of the CAHPS Cultural Competency Item Set (CAHPS-CC), no measures capturing patient-level experiences with culturally competent care have been suitable for broad-scale administration. Methods We performed confirmatory factor analysis and internal consistency reliability analysis of CAHPS-CC among patients with type 2 diabetes (n=600) receiving primary care in safety-net clinics. CAHPS-CC domains were also correlated with global physician ratings. Results A 7-factor model demonstrated satisfactory fit (χ2(231)=484.34, p<.0001) with significant factor loadings at p<.05. Three domains showed excellent reliability – Doctor Communication- Positive Behaviors (α=.82), Trust (α=.77), and Doctor Communication- Health Promotion (α=.72). Four domains showed inadequate reliability either among Spanish speakers or overall (overall reliabilities listed): Doctor Communication- Negative Behaviors (α=.54), Equitable Treatment (α=.69), Doctor Communication- Alternative Medicine (α=.52), and Shared Decision-Making (α=.51). CAHPS-CC domains were positively and significantly correlated with global physician rating. Conclusions Select CAHPS-CC domains are suitable for broad-scale administration among safety-net patients. Those domains may be used to target quality-improvement efforts focused on providing culturally competent care in safety-net settings. PMID:22895231
Luo, Yong; Wu, Wenqi; Babu, Ravindra; Tang, Kanghua; Luo, Bing
2012-01-01
COMPASS is an indigenously developed Chinese global navigation satellite system and will share many features in common with GPS (Global Positioning System). Since the ultra-tight GPS/INS (Inertial Navigation System) integration shows its advantage over independent GPS receivers in many scenarios, the federated ultra-tight COMPASS/INS integration has been investigated in this paper, particularly, by proposing a simplified prefilter model. Compared with a traditional prefilter model, the state space of this simplified system contains only carrier phase, carrier frequency and carrier frequency rate tracking errors. A two-quadrant arctangent discriminator output is used as a measurement. Since the code tracking error related parameters were excluded from the state space of traditional prefilter models, the code/carrier divergence would destroy the carrier tracking process, and therefore an adaptive Kalman filter algorithm tuning process noise covariance matrix based on state correction sequence was incorporated to compensate for the divergence. The federated ultra-tight COMPASS/INS integration was implemented with a hardware COMPASS intermediate frequency (IF), and INS's accelerometers and gyroscopes signal sampling system. Field and simulation test results showed almost similar tracking and navigation performances for both the traditional prefilter model and the proposed system; however, the latter largely decreased the computational load. PMID:23012564
Intelligent Energy Management System for PV-Battery-based Microgrids in Future DC Homes
NASA Astrophysics Data System (ADS)
Chauhan, R. K.; Rajpurohit, B. S.; Gonzalez-Longatt, F. M.; Singh, S. N.
2016-06-01
This paper presents a novel intelligent energy management system (IEMS) for a DC microgrid connected to the public utility (PU), photovoltaic (PV) and multi-battery bank (BB). The control objectives of the proposed IEMS system are: (i) to ensure the load sharing (according to the source capacity) among sources, (ii) to reduce the power loss (high efficient) in the system, and (iii) to enhance the system reliability and power quality. The proposed IEMS is novel because it follows the ideal characteristics of the battery (with some assumptions) for the power sharing and the selection of the closest source to minimize the power losses. The IEMS allows continuous and accurate monitoring with intelligent control of distribution system operations such as battery bank energy storage (BBES) system, PV system and customer utilization of electric power. The proposed IEMS gives the better operational performance for operating conditions in terms of load sharing, loss minimization, and reliability enhancement of the DC microgrid.
NASA Technical Reports Server (NTRS)
Kalt, A. C.
1975-01-01
Certain climatic tests which require solar and sky radiation were carried out in the laboratory by using simulated global radiation. The advantages of such a method of measurement and the possibilities and limitations resulting from the simulation of global radiation are described. Experiments concerning the thermal load in rooms were conducted in order to test the procedure. In particular, the heat gain through a window with sunshade is discussed, a venetian blind between the panes of a double-glazed window being used in most cases.
Lin, Chieh-Peng
2010-12-01
This study proposes a model explaining how social capital helps ease excessively required mental effort. Although organizational researchers have studied both social capital and cognitive load, no prior research has critically examined the role of social capital in improving individuals' mental load and effort and consequently enhancing job learning effectiveness. This study surveys participants made up of professionals in Taiwan's information technology industry. It measures the constructs with the use of 5-point Likert-type scale items modified from existing literature. The survey data were analyzed with the use of structural equation modeling. Job learning effectiveness is negatively influenced by role ambiguity and role conflict. Time pressure has a positive influence on role ambiguity and role conflict Although the relationship between task complexity and role ambiguity is insignificant, task complexity has a positive influence on role conflict. Because the relationship between network ties and role conflict is insignificant, trust has a negative influence on role conflict. Last, shared vision has a negative influence on role ambiguity. This study provides an example of how social capital can be applied as a useful remedy to ease the negative impact of perceived cognitive load on job learning effectiveness. The negative relationship between shared vision and role ambiguity suggests that a shared vision helps in disseminating organizationally common goals and directions among employees to alleviate individuals' mental efforts in dealing with the ambiguity of their job roles. A firm's management team should take actions to decrease role conflict by strengthening trust among employees.
Athey, Brian D; Braxenthaler, Michael; Haas, Magali; Guo, Yike
2013-01-01
tranSMART is an emerging global open source public private partnership community developing a comprehensive informatics-based analysis and data-sharing cloud platform for clinical and translational research. The tranSMART consortium includes pharmaceutical and other companies, not-for-profits, academic entities, patient advocacy groups, and government stakeholders. The tranSMART value proposition relies on the concept that the global community of users, developers, and stakeholders are the best source of innovation for applications and for useful data. Continued development and use of the tranSMART platform will create a means to enable "pre-competitive" data sharing broadly, saving money and, potentially accelerating research translation to cures. Significant transformative effects of tranSMART includes 1) allowing for all its user community to benefit from experts globally, 2) capturing the best of innovation in analytic tools, 3) a growing 'big data' resource, 4) convergent standards, and 5) new informatics-enabled translational science in the pharma, academic, and not-for-profit sectors.
NASA Technical Reports Server (NTRS)
Pollack, J. B.; Colburn, D. S.
1984-01-01
During the first Viking year, two global dust storms occurred and they contributed about 90% of the dust suspended in the Martian atmosphere on a global average, over the course of this year. The remainder was due to the cumulative effect of local dust storms. When globally distributed, the amount of suspended dust introduced into the atmosphere this Martian year was about 5x10(-3) g/sq cm. This mass loading was derived from the incremental optical depths measured over this year and estimates of the mean size of the dust particles (2.5 microns). During the second Martian year, global dust storms were far more muted than during the first year. No near perihelion dust storm occurred, and a somewhat weaker dust storm may have occurred near the start of the spring season in the Southern Hemisphere, at about the same time that the first global dust storm of the first year occurred. Thus, the dust loading derived for the first Martian year may be somewhat higher than the average over many Martian years, a conclusion that appears to be supported by preliminary studies of Martian years beyond the second Viking year on Mars.
Foolad, Negar; Ornelas, Jennifer N; Clark, Ashley K; Ali, Ifrah; Sharon, Victoria R; Al Mubarak, Luluah; Lopez, Andrés; Alikhan, Ali; Al Dabagh, Bishr; Firooz, Alireza; Awasthi, Smita; Liu, Yu; Li, Chin-Shang; Sivamani, Raja K
2017-09-01
Cloud-based image sharing technology allows facilitated sharing of images. Cloud-based image sharing technology has not been well-studied for acne assessments or treatment preferences, among international evaluators. We evaluated inter-rater variability of acne grading and treatment recommendations among an international group of dermatologists that assessed photographs. This is a prospective, single visit photographic study to assess inter-rater agreement of acne photographs shared through an integrated mobile device, cloud-based, and HIPAA-compliant platform. Inter-rater agreements for global acne assessment and acne lesion counts were evaluated by the Kendall's coefficient of concordance while correlations between treatment recommendations and acne severity were calculated by Spearman's rank correlation coefficient. There was good agreement for the evaluation of inflammatory lesions (KCC = 0.62, P < 0.0001), noninflammatory lesions (KCC = 0.62, P < 0.0001), and the global acne grading system score (KCC = 0.69, P < 0.0001). Topical retinoid, oral antibiotic, and isotretinoin treatment preferences correlated with photographic based acne severity. Our study supports the use of mobile phone based photography and cloud-based image sharing for acne assessment. Cloud-based sharing may facilitate acne care and research among international collaborators. © 2017 The International Society of Dermatology.
Load sharing in distributed real-time systems with state-change broadcasts
NASA Technical Reports Server (NTRS)
Shin, Kang G.; Chang, Yi-Chieh
1989-01-01
A decentralized dynamic load-sharing (LS) method based on state-change broadcasts is proposed for a distributed real-time system. Whenever the state of a node changes from underloaded to fully loaded and vice versa, the node broadcasts this change to a set of nodes, called a buddy set, in the system. The performance of the method is evaluated with both analytic modeling and simulation. It is modeled first by an embedded Markov chain for which numerical solutions are derived. The model solutions are then used to calculate the distribution of queue lengths at the nodes and the probability of meeting task deadlines. The analytical results show that buddy sets of 10 nodes outperform those of less than 10 nodes, and the incremental benefit gained from increasing the buddy set size beyond 15 nodes is insignificant. These and other analytical results are verified by simulation. The proposed LS method is shown to meet task deadlines with a very high probability.
Polygenic loading for major depression is associated with specific medical comorbidity
McCoy, T H; Castro, V M; Snapper, L; Hart, K; Januzzi, J L; Huffman, J C; Perlis, R H
2017-01-01
Major depressive disorder frequently co-occurs with medical disorders, raising the possibility of shared genetic liability. Recent identification of 15 novel genetic loci associated with depression allows direct investigation of this question. In cohorts of individuals participating in biobanks at two academic medical centers, we calculated polygenic loading for risk loci reported to be associated with depression. We then examined the association between such loading and 50 groups of clinical diagnoses, or topics, drawn from these patients' electronic health records, determined using a novel application of latent Dirichilet allocation. Three topics showed experiment-wide association with the depression liability score; these included diagnostic groups representing greater prevalence of mood and anxiety disorders, greater prevalence of cardiac ischemia, and a decreased prevalence of heart failure. The latter two associations persisted even among individuals with no mood disorder diagnosis. This application of a novel method for grouping related diagnoses in biobanks indicate shared genetic risk for depression and cardiac disease, with a pattern suggesting greater ischemic risk and diminished heart failure risk. PMID:28926002
Increased nitrogen loading has been directly linked to the proliferation of planktonic and macroalgal blooms at a global scale with negative impacts on estuarine ecology and human health. Under excessive anthropogenic nutrient loads, seagrass systems can be replaced by either ma...
Testing Orions Fairing Separation System
NASA Technical Reports Server (NTRS)
Martinez, Henry; Cloutier, Chris; Lemmon, Heber; Rakes, Daniel; Oldham, Joe; Schlagel, Keith
2014-01-01
Traditional fairing systems are designed to fully encapsulate and protect their payload from the harsh ascent environment including acoustic vibrations, aerodynamic forces and heating. The Orion fairing separation system performs this function and more by also sharing approximately half of the vehicle structural load during ascent. This load-share condition through launch and during jettison allows for a substantial increase in mass to orbit. A series of component-level development tests were completed to evaluate and characterize each component within Orion's unique fairing separation system. Two full-scale separation tests were performed to verify system-level functionality and provide verification data. This paper summarizes the fairing spring, Pyramidal Separation Mechanism and forward seal system component-level development tests, system-level separation tests, and lessons learned.
Dynamic programming on a shared-memory multiprocessor
NASA Technical Reports Server (NTRS)
Edmonds, Phil; Chu, Eleanor; George, Alan
1993-01-01
Three new algorithms for solving dynamic programming problems on a shared-memory parallel computer are described. All three algorithms attempt to balance work load, while keeping synchronization cost low. In particular, for a multiprocessor having p processors, an analysis of the best algorithm shows that the arithmetic cost is O(n-cubed/6p) and that the synchronization cost is O(absolute value of log sub C n) if p much less than n, where C = (2p-1)/(2p + 1) and n is the size of the problem. The low synchronization cost is important for machines where synchronization is expensive. Analysis and experiments show that the best algorithm is effective in balancing the work load and producing high efficiency.
Haemophilus influenzae Disease (Including Hib) Symptoms
... Links Global Hib Vaccination Hib Vaccination Meningitis Pneumonia Sepsis Signs and Symptoms Recommend on Facebook Tweet Share ... Links Global Hib Vaccination Hib Vaccination Meningitis Pneumonia Sepsis File Formats Help: How do I view different ...
Microgrid Study: Energy Security for DoD Installations
2012-06-18
security, efficiency, and the incorporation of renewable and distributed energy resources into microgrids, as well as the factors that might facilitate...better understand how different environmental factors affected the choice of optimal microgrid architecture. Environmental factors in this context...lower costs—Networking generation assets allow for load sharing, allowing fewer generators to run at higher load factors and therefore with greater
Berard, Frederic; Blanco, Patrick; Davoust, Jean; Neidhart-Berard, Eve-Marie; Nouri-Shirazi, Mahyar; Taquet, Nicolas; Rimoldi, Donata; Cerottini, Jean Charles; Banchereau, Jacques; Palucka, A. Karolina
2000-01-01
The goal of tumor immunotherapy is to elicit immune responses against autologous tumors. It would be highly desirable that such responses include multiple T cell clones against multiple tumor antigens. This could be obtained using the antigen presenting capacity of dendritic cells (DCs) and cross-priming. That is, one could load the DC with tumor lines of any human histocompatibility leukocyte antigen (HLA) type to elicit T cell responses against the autologous tumor. In this study, we show that human DCs derived from monocytes and loaded with killed melanoma cells prime naive CD45RA+CD27+CD8+ T cells against the four shared melanoma antigens: MAGE-3, gp100, tyrosinase, and MART-1. HLA-A201+ naive T cells primed by DCs loaded with HLA-A201− melanoma cells are able to kill several HLA-A201+ melanoma targets. Cytotoxic T lymphocyte priming towards melanoma antigens is also obtained with cells from metastatic melanoma patients. This demonstration of cross-priming against shared tumor antigens builds the basis for using allogeneic tumor cell lines to deliver tumor antigens to DCs for vaccination protocols. PMID:11104796
The Empirical Analysis of Impact of Alliances on Airline Operations
NASA Technical Reports Server (NTRS)
Iatrou, Kostas; Alamdari, Fariba
2003-01-01
Airline alliances are dominating the current air transport industry with the largest carriers of the world belonging to one of the four alliance groupings - "Wings", Star Alliance, one world, SkyTeam - which represent 56% of world Revenue Passenger Kilometers. Although much research has been carried out to evaluate the impact of alliance membership on performance of airlines, it would be of interest to ascertain the degree of impact perceived by participating airlines in alliances. It is the purpose of this paper to gather the opinion of all the airlines, belonging to the four global alliance groupings on the impact alliances have had on their traffic and on their performance in general To achieve this, a comprehensive survey of the alliance management departments of airlines participating in the four global strategic alliances was carried out. With this framework the survey has examined which type of cooperation among carriers (FFP, Code Share, Strategic Alliance without antitrust immunity, Strategic Alliance with antitrust immunity) has produced the most positive impact on traffic and which type of route (short haul, long haul, hub-hub, hub-non hub, non hub-non hub) has been mostly affected. In addition, the respondent airlines quantified the effect alliances have had on specific areas of their operation, such as load factors, traffic, costs, revenue and fares. Their responses have been analysed under each global alliances grouping, under airline and under geographic region to establish which group, type of carrier and geographic region has benefited most. The results show that each of the four global alliances groupings has experienced different results according to the type of collaboration agreed amongst their member airlines.
NASA Technical Reports Server (NTRS)
Smrekar, S. E.; Anderson, F. S.
2005-01-01
We have calculated admittance spectra using the spatio-spectral method [14] for Venus by moving the central location of the spectrum over a 1 grid, create 360x180 admittance spectra. We invert the observed admittance using top-loading (TL), hot spot (HS), and bottom loading (BL) models, resulting in elastic, crustal, and lithospheric thickness estimates (Te, Zc, and Zl) [0]. The result is a global map for interpreting subsurface structure. Estimated values of Te and Zc concur with previous TL local admittance results, but BL estimates indicate larger values than previously suspected.
Tropical Cyclones as a Driver of Global Sediment Flux
NASA Astrophysics Data System (ADS)
Leyland, J.; Darby, S. E.; Cohen, S.
2017-12-01
The world's rivers deliver 19 billion tonnes of sediment to the coastal zone annually. The sediment supplied to the coastal zone is of significant importance for a variety of reasons, for example in acting as a vector for nutrients as well as in supplying sediment to coastal landforms such as deltas and beaches that can buffer those landforms from erosion and flooding. A greater understanding of the factors governing sediment flux to the oceans is therefore a key research gap. The non-linear relationship between river discharge and sediment flux implies that the global sediment flux may be disproportionately driven by large floods. Indeed, in our recent empirical research we have demonstrated that changes in the track locations, frequency and intensity of tropical storms in recent decades exert a significant control on the sediment flux emanating from the Mekong River. Since other large rivers potentially affected by tropical storms are known to make a significant contribution to the global sediment flux, this raises the question of the extent to which such storms play a significant role in controlling sediment loads at the global scale. In this paper we address that question by employing a global hydrological model (WBMsed) in order to predict runoff and sediment load forced by recent historical climate scenarios `with' and `without' tropical cyclones. We compare the two scenarios to (i) make the first estimate of the global contribution of sediment load forced by tropical storms; (ii) evaluate how that contribution has varied in recent decades and to (iii) explore variations in tropical-storm driven sediment loads in selected major river basins that are significantly affected by such storms.
NASA Technical Reports Server (NTRS)
Estes, R. H.
1977-01-01
A computer software system is described which computes global numerical solutions of the integro-differential Laplace tidal equations, including dissipation terms and ocean loading and self-gravitation effects, for arbitrary diurnal and semidiurnal tidal constituents. The integration algorithm features a successive approximation scheme for the integro-differential system, with time stepping forward differences in the time variable and central differences in spatial variables.
Interacting damage models mapped onto ising and percolation models
DOE Office of Scientific and Technical Information (OSTI.GOV)
Toussaint, Renaud; Pride, Steven R.
The authors introduce a class of damage models on regular lattices with isotropic interactions between the broken cells of the lattice. Quasistatic fiber bundles are an example. The interactions are assumed to be weak, in the sense that the stress perturbation from a broken cell is much smaller than the mean stress in the system. The system starts intact with a surface-energy threshold required to break any cell sampled from an uncorrelated quenched-disorder distribution. The evolution of this heterogeneous system is ruled by Griffith's principle which states that a cell breaks when the release in potential (elastic) energy in themore » system exceeds the surface-energy barrier necessary to break the cell. By direct integration over all possible realizations of the quenched disorder, they obtain the probability distribution of each damage configuration at any level of the imposed external deformation. They demonstrate an isomorphism between the distributions so obtained and standard generalized Ising models, in which the coupling constants and effective temperature in the Ising model are functions of the nature of the quenched-disorder distribution and the extent of accumulated damage. In particular, they show that damage models with global load sharing are isomorphic to standard percolation theory, that damage models with local load sharing rule are isomorphic to the standard ising model, and draw consequences thereof for the universality class and behavior of the autocorrelation length of the breakdown transitions corresponding to these models. they also treat damage models having more general power-law interactions, and classify the breakdown process as a function of the power-law interaction exponent. Last, they also show that the probability distribution over configurations is a maximum of Shannon's entropy under some specific constraints related to the energetic balance of the fracture process, which firmly relates this type of quenched-disorder based damage model to standard statistical mechanics.« less
A surface code quantum computer in silicon
Hill, Charles D.; Peretz, Eldad; Hile, Samuel J.; House, Matthew G.; Fuechsle, Martin; Rogge, Sven; Simmons, Michelle Y.; Hollenberg, Lloyd C. L.
2015-01-01
The exceptionally long quantum coherence times of phosphorus donor nuclear spin qubits in silicon, coupled with the proven scalability of silicon-based nano-electronics, make them attractive candidates for large-scale quantum computing. However, the high threshold of topological quantum error correction can only be captured in a two-dimensional array of qubits operating synchronously and in parallel—posing formidable fabrication and control challenges. We present an architecture that addresses these problems through a novel shared-control paradigm that is particularly suited to the natural uniformity of the phosphorus donor nuclear spin qubit states and electronic confinement. The architecture comprises a two-dimensional lattice of donor qubits sandwiched between two vertically separated control layers forming a mutually perpendicular crisscross gate array. Shared-control lines facilitate loading/unloading of single electrons to specific donors, thereby activating multiple qubits in parallel across the array on which the required operations for surface code quantum error correction are carried out by global spin control. The complexities of independent qubit control, wave function engineering, and ad hoc quantum interconnects are explicitly avoided. With many of the basic elements of fabrication and control based on demonstrated techniques and with simulated quantum operation below the surface code error threshold, the architecture represents a new pathway for large-scale quantum information processing in silicon and potentially in other qubit systems where uniformity can be exploited. PMID:26601310
A surface code quantum computer in silicon.
Hill, Charles D; Peretz, Eldad; Hile, Samuel J; House, Matthew G; Fuechsle, Martin; Rogge, Sven; Simmons, Michelle Y; Hollenberg, Lloyd C L
2015-10-01
The exceptionally long quantum coherence times of phosphorus donor nuclear spin qubits in silicon, coupled with the proven scalability of silicon-based nano-electronics, make them attractive candidates for large-scale quantum computing. However, the high threshold of topological quantum error correction can only be captured in a two-dimensional array of qubits operating synchronously and in parallel-posing formidable fabrication and control challenges. We present an architecture that addresses these problems through a novel shared-control paradigm that is particularly suited to the natural uniformity of the phosphorus donor nuclear spin qubit states and electronic confinement. The architecture comprises a two-dimensional lattice of donor qubits sandwiched between two vertically separated control layers forming a mutually perpendicular crisscross gate array. Shared-control lines facilitate loading/unloading of single electrons to specific donors, thereby activating multiple qubits in parallel across the array on which the required operations for surface code quantum error correction are carried out by global spin control. The complexities of independent qubit control, wave function engineering, and ad hoc quantum interconnects are explicitly avoided. With many of the basic elements of fabrication and control based on demonstrated techniques and with simulated quantum operation below the surface code error threshold, the architecture represents a new pathway for large-scale quantum information processing in silicon and potentially in other qubit systems where uniformity can be exploited.
Global Competency Education Catches Fire at a Rural University
ERIC Educational Resources Information Center
Talbot, Patricia A.; Gustafson, Glenna; Mistele, Jean
2017-01-01
World-ready learners require world-ready educators. One group of inspiring teacher educators share how they ignited a fire of awareness around the importance of global competency education at a small, rural teacher college.
Numerical Characterization of a Composite Bonded Wing-Box
NASA Technical Reports Server (NTRS)
Smeltzer, Stanley S., III; Lovejoy, Andrew E.; Satyanarayana, Arunkumar
2008-01-01
The development of composite wing structures has focused on the use of mechanical fasteners to join heavily-loaded areas, while bonded joints have been used only for select locations. The focus of this paper is the examination of the adhesive layer in a generic bonded wing box that represents a "fastenerless" or unitized structure in order to characterize the general behavior and failure mechanisms. A global/local approach was applied to study the response of the adhesive layer using a global shell model and a local shell/solid model. The wing box was analyzed under load to represent a high-g up-bending condition such that the strains in the composite sandwich face sheets are comparable to an expected design allowable. The global/local analysis indicates that at these wing load levels the strains in the adhesive layer are well within the adhesive's elastic region, such that yielding would not be expected in the adhesive layer. The global/local methodology appears to be a promising approach to evaluate the structural integrity of the adhesively bonded structures.
Liu, Da; Xu, Ming; Niu, Dongxiao; Wang, Shoukai; Liang, Sai
2016-01-01
Traditional forecasting models fit a function approximation from dependent invariables to independent variables. However, they usually get into trouble when date are presented in various formats, such as text, voice and image. This study proposes a novel image-encoded forecasting method that input and output binary digital two-dimensional (2D) images are transformed from decimal data. Omitting any data analysis or cleansing steps for simplicity, all raw variables were selected and converted to binary digital images as the input of a deep learning model, convolutional neural network (CNN). Using shared weights, pooling and multiple-layer back-propagation techniques, the CNN was adopted to locate the nexus among variations in local binary digital images. Due to the computing capability that was originally developed for binary digital bitmap manipulation, this model has significant potential for forecasting with vast volume of data. The model was validated by a power loads predicting dataset from the Global Energy Forecasting Competition 2012.
Coordinated single-phase control scheme for voltage unbalance reduction in low voltage network.
Pullaguram, Deepak; Mishra, Sukumar; Senroy, Nilanjan
2017-08-13
Low voltage (LV) distribution systems are typically unbalanced in nature due to unbalanced loading and unsymmetrical line configuration. This situation is further aggravated by single-phase power injections. A coordinated control scheme is proposed for single-phase sources, to reduce voltage unbalance. A consensus-based coordination is achieved using a multi-agent system, where each agent estimates the averaged global voltage and current magnitudes of individual phases in the LV network. These estimated values are used to modify the reference power of individual single-phase sources, to ensure system-wide balanced voltages and proper power sharing among sources connected to the same phase. Further, the high X / R ratio of the filter, used in the inverter of the single-phase source, enables control of reactive power, to minimize voltage unbalance locally. The proposed scheme is validated by simulating a LV distribution network with multiple single-phase sources subjected to various perturbations.This article is part of the themed issue 'Energy management: flexibility, risk and optimization'. © 2017 The Author(s).
Xu, Ming; Niu, Dongxiao; Wang, Shoukai; Liang, Sai
2016-01-01
Traditional forecasting models fit a function approximation from dependent invariables to independent variables. However, they usually get into trouble when date are presented in various formats, such as text, voice and image. This study proposes a novel image-encoded forecasting method that input and output binary digital two-dimensional (2D) images are transformed from decimal data. Omitting any data analysis or cleansing steps for simplicity, all raw variables were selected and converted to binary digital images as the input of a deep learning model, convolutional neural network (CNN). Using shared weights, pooling and multiple-layer back-propagation techniques, the CNN was adopted to locate the nexus among variations in local binary digital images. Due to the computing capability that was originally developed for binary digital bitmap manipulation, this model has significant potential for forecasting with vast volume of data. The model was validated by a power loads predicting dataset from the Global Energy Forecasting Competition 2012. PMID:27281032
Globalization, English Language Teaching and Turkey
ERIC Educational Resources Information Center
Altan, Mustafa Zülküf
2017-01-01
Globalization as a concept has been used both positively and negatively by many different people and in many different situations. Depending on the point of view, all definitions on globalization state that it has the power of creating a world without boundaries where people communicate, share, and do business with the help of information,…
75 FR 7637 - iShares Trust, et al.; Notice of Application
Federal Register 2010, 2011, 2012, 2013, 2014
2010-02-22
... ETFs.\\5\\ \\4\\ See, e.g., South Asia Portfolio, SEC No-Action Letter (Mar. 12, 1997). \\5\\ Barclays Global... Global Fund Advisors, et al., Investment Company Act Release No. 26175 (Sep. 8, 2003), and Barclays Global Fund Advisors, et al., Investment Company Act Release No. 27417 (Jun. 23, 2006) (as amended, the...
Sociological Implications of English as an International Language in Music Education
ERIC Educational Resources Information Center
Kertz-Welzel, Alexandra
2016-01-01
Internationalization and globalization have created a global music education community which is not only linked by similar ideas, but also shares a common language. English functions as a global language and facilitates the international discourse in music education. While it is good to have a common language supporting international dialogue, it…
ERIC Educational Resources Information Center
Ivy, Karen Lynne-Daniels
2017-01-01
This paper shares the findings of a study conducted on a virtual inter-cultural global leadership development learning project. Mixed Methods analysis techniques were used to examine the interviews of U.S. and Uganda youth project participants. The study, based on cultural and social constructivist learning theories, investigated the effects of…
Gray, Adrian J; Shorter, Kathleen; Cummins, Cloe; Murphy, Aron; Waldron, Mark
2018-06-01
Quantifying the training and competition loads of players in contact team sports can be performed in a variety of ways, including kinematic, perceptual, heart rate or biochemical monitoring methods. Whilst these approaches provide data relevant for team sports practitioners and athletes, their application to a contact team sport setting can sometimes be challenging or illogical. Furthermore, these methods can generate large fragmented datasets, do not provide a single global measure of training load and cannot adequately quantify all key elements of performance in contact team sports. A previous attempt to address these limitations via the estimation of metabolic energy demand (global energy measurement) has been criticised for its inability to fully quantify the energetic costs of team sports, particularly during collisions. This is despite the seemingly unintentional misapplication of the model's principles to settings outside of its intended use. There are other hindrances to the application of such models, which are discussed herein, such as the data-handling procedures of Global Position System manufacturers and the unrealistic expectations of end users. Nevertheless, we propose an alternative energetic approach, based on Global Positioning System-derived data, to improve the assessment of mechanical load in contact team sports. We present a framework for the estimation of mechanical work performed during locomotor and contact events with the capacity to globally quantify the work done during training and matches.
2010-08-01
using load - bearing tanks with parasitic TPS was considered to be a lower weight design when all details were accounted for. The cold structure...share one very key element with the design of load bearing hot structure – the design drive toward thin gauge metallic skin under complex and coupled...39 skin panel joints and their susceptibility to high acoustic loading coupled with transient heating, and hot structure skin deflections and
Gearbox Reliability Collaborative Gearbox 3 Planet Bearing Calibration
DOE Office of Scientific and Technical Information (OSTI.GOV)
Keller, Jonathan
2017-03-24
The Gearbox Reliability Collaborative gearbox was redesigned to improve its load-sharing characteristics and predicted fatigue life. The most important aspect of the redesign was to replace the cylindrical roller bearings with preloaded tapered roller bearings in the planetary section. Similar to previous work, the strain gages installed on the planet tapered roller bearings were calibrated in a load frame. This report describes the calibration tests and provides the factors necessary to convert the measured units from dynamometer testing to bearing loads, suitable for comparison to engineering models.
NASA Technical Reports Server (NTRS)
Ku, Jentung; Ottenstein, Laura; Birur, Gajanana
2004-01-01
This paper describes thermal performance of a loop heat pipe (LHP) with two evaporators and two condensers in ambient testing. Each evaporator has an outer diameter of 15mm and a length of 76mm, and has an integral compensation chamber (CC). An aluminum mass of 500 grams is attached to each evaporator to simulate the instrument mass. A thermal electric cooler (TEC) is installed on each CC to provide heating as well as cooling for CC temperature control. A flow regulator is installed in the condenser section to prevent vapor from going back to the evaporators in the event that one of condenser is fully utilized. Ammonia was used ad the working fluid. Tests conducted included start-up, power cycle, heat load sharing, sink temperature cycle, operating temperature control with TECs, and capillary limit tests. Experimental data showed that the loop could start with a heat load of less than 1OW even with added thermal masses. The loop operated stably with even and uneven evaporator heat loads, and even and uneven condenser sink temperatures. The operating temperature could be controlled within +/-0.5K of the set point temperature using either or both TECs, and the required TEC control heater power was less than 2W under most test conditions. Heat load sharing between the two evaporators was also successfully demonstrated. The loop had a heat transport capability of 120W to 140W, and could recover from a dry-out when the heat load was reduced. The 500-gram aluminum mass on each evaporator had a negligible effect on the loop operation. Existing LHPs servicing the orbiting spacecraft have a single evaporator with an outer diameter of about 25mm. Important performance characteristics demonstrated by this LHP included: 1) Operation of an LHP with 15mm diameter evaporators; 2) Robustness and reliability of an LHP with multiple evaporators and multiple condensers under various test conditions; 3) Heat load sharing among LHP evaporators; 4) Effectiveness of TECs in controlling the LHP operating temperature; and 5) Effectiveness of the flow regulator in preventing vapor from going back the evaporators.
NASA Technical Reports Server (NTRS)
Ku, Jen-Tung; Ottenstein, Laura; Birur, Gajanana
2004-01-01
This paper describes thermal performance of a loop heat pipe (LHP) with two evaporators and two condensers in ambient testing. Each evaporator has an outer diameter of 15mm and a length of 76mm, and has an integral compensation chamber (CC). An aluminum mass of 500 grams is attached to each evaporator to simulate the instrument mass. A thermoelectric cooler (TEC) is installed on each CC to provide heating as well as cooling for CC temperature control. A flow regulator is installed in the condenser section to prevent vapor from going back to the evaporators in the event that one of the condensers is fully utilized. Ammonia was used as the working fluid. Tests conducted included start-up, power cycle, heat load sharing, sink temperature cycle, operating temperature control with TECs, and capillary limit tests. Experimental data showed that the loop could start with a heat load of less than 10W even with added thermal masses. The loop operated stably with even and uneven evaporator heat loads, and even and uneven condenser sink temperatures. The operating temperature could be controlled within +/- 0.5K of the set point temperature using either or both TECs, and the required TEC control heater power was less than 2W under most test conditions. Heat load sharing between the two evaporators was also successfully demonstrated. The loop had a heat transport capability of 120W to 140W, and could recover from a dry-out when the heat load was reduced. The 500-gram aluminum mass on each evaporator had a negligible effect on the loop operation. Existing LHPs servicing orbiting spacecraft have a single evaporator with an outer diameter of about 25mm. Important performance characteristics demonstrated by this LHP included: 1) Operation of an LHP with 15mm diameter evaporators; 2) Robustness and reliability of an LHP with multiple evaporators and multiple condensers under various test conditions; 3) Heat load sharing among LHP evaporators; 4) Effectiveness of TECs in controlling the LHP operating temperature; and 5 ) Effectiveness of the flow regulator in preventing vapor from going back the evaporators.
Epilepsy Research in India: A Scientometric Analysis of Publications Output during 2002-11.
Gupta, Brij M; Bala, Adarsh
2013-04-01
This study analyses the research output of India in epilepsy research during 2002-11 on several parameters including the growth, rank and global publications share, citation impact, share of international collaborative papers, contribution of major collaborative partner countries, contribution of various subject-fields, contribution and impact of most productive institutions and authors, media of communication and characteristics of high cited papers. The Scopus Citation Database has been used to retrieve the data for 10 years (2002-11) by searching the keywords "epilepsy research" in the combined Title, Abstract and Keywords fields. Among the top 20 most productive countries in epilepsy research, India ranks at 11(th) position (with 1550 papers) with a global publication share of 2.88% and an annual average publication growth rate of 15.31% during 2002-11. Its global publication share has increased over the years, rising from 2.06% in 2002 to 4.65% during 2011. Its citation impact per paper was 2.77 during 2002-11, which decreased from 3.48 during 2002-06 to 2.41 during 2007-11. Its international collaborative publications share was 12.32% during 2002-11, which decreased from 12.45% during 2002-06 to 12.26% during 2007-11. Concludes that India needs to increase both the quantity and quality of research and also the need to share research data and stimulate national and international collaborative research, which will increase both the quantity and quality of research in epilepsy. There is a need to develop a national program on epilepsy as a part of national health plan, besides suggesting the funding agencies to establish a more ambitious funding program into the causes, prevention, cure and care of epilepsy. There is a need to build capacity at all levels of human resources for the management of epilepsy.
Knowledge networks for global public health.
Natividad, Maria Dulce F; Fiereck, Kirk J; Parker, Richard
2012-01-01
The challenges posed by a globalised world have made it imperative for society to search for solutions to emerging issues and to develop new ways of looking at old problems. Current discussions about global public health demand a shift in paradigms and the strategic positioning of public health within broader policy discussions that will enable it to influence political and action agendas. Critical to responding to these challenges is the generation, transmission and dissemination of new knowledge to create value. Recognising the cutting-edge role of knowledge, as a new form of capital that drives innovation and transforms society, the formation of knowledge networks is viewed as a strategy for developing a shared intellectual, conceptual and ethical infrastructure for the field of global public health. These knowledge networks are envisioned as a vehicle for sharing diverse perspectives, encouraging debate and sustaining alternative ways of thinking about and responding to the challenges that confront global public health today and in the future.
Application Architecture of Avian Influenza Research Collaboration Network in Korea e-Science
NASA Astrophysics Data System (ADS)
Choi, Hoon; Lee, Junehawk
In the pursuit of globalization of the AI e-Science environment, KISTI is fostering to extend the AI research community to the AI research institutes of neighboring countries and to share the AI e-Science environment with them in the near future. In this paper we introduce the application architecture of AI research collaboration network (AIRCoN). AIRCoN is a global e-Science environment for AI research conducted by KISTI. It consists of AI virus sequence information sharing system for sufficing data requirement of research community, integrated analysis environment for analyzing the mutation pattern of AI viruses and their risks, epidemic modeling and simulation environment for establishing national effective readiness strategy against AI pandemics, and knowledge portal for sharing expertise of epidemic study and unpublished research results with community members.
A tale of two cultures: specialists and generalists sharing the load.
Manca, Donna P; Breault, Lorraine; Wishart, Paul
2011-05-01
To understand what contributes to good collaborative physician working relationships through identifying the factors that affect working relationships between generalist physicians and specialists. Qualitative study using in-depth interviews. University and community hospital inpatient family practice settings in Edmonton, Alta. Eleven physicians from various specialties who graduated between 1977 and 2001. A grounded-theory approach, including constant comparison and creation of memorandums, helped to conceptualize the main concern and generated a framework for how the main concern was being resolved. A semistructured interview guide was developed and individual, in-depth interviews were audiotaped. Purposeful and theoretical sampling techniques were used. Three researchers participated in the analysis. The findings suggested that when generalist physicians perceived that work had been imposed on them by specialists without negotiation, they felt overwhelmed by the workload. Differing priorities determined whether physicians were left holding the bag or sharing the load. In a system that valued technology and specialized knowledge and skills, the specialists were better able to control resources, set boundaries, and influence learners. This precipitated a culture of protecting valuable specialty resources, increasing physician isolation, and generalists feeling that they were left holding the bag. In order to reverse this cycle, it was important for physicians to develop good working relationships based on accessibility to needed expertise and tests, with negotiated agreements on how to share resources; mutual empowerment, including negotiation of roles and responsibilities to develop flexible relationships with a clear understanding of roles; and concern for fairness by sharing the load. Medical systems that value technology and focused interests might lead to someone being left holding the bag, contributing to generalists feeling overwhelmed and isolated within the system. A comprehensive system that values relationships might help to resolve issues created through perceived inequities in workload, disempowerment, and lack of understanding of roles.
Evaluation of Analysis Techniques for Fluted-Core Sandwich Cylinders
NASA Technical Reports Server (NTRS)
Lovejoy, Andrew E.; Schultz, Marc R.
2012-01-01
Buckling-critical launch-vehicle structures require structural concepts that have high bending stiffness and low mass. Fluted-core, also known as truss-core, sandwich construction is one such concept. In an effort to identify an analysis method appropriate for the preliminary design of fluted-core cylinders, the current paper presents and compares results from several analysis techniques applied to a specific composite fluted-core test article. The analysis techniques are evaluated in terms of their ease of use and for their appropriateness at certain stages throughout a design analysis cycle (DAC). Current analysis techniques that provide accurate determination of the global buckling load are not readily applicable early in the DAC, such as during preliminary design, because they are too costly to run. An analytical approach that neglects transverse-shear deformation is easily applied during preliminary design, but the lack of transverse-shear deformation results in global buckling load predictions that are significantly higher than those from more detailed analysis methods. The current state of the art is either too complex to be applied for preliminary design, or is incapable of the accuracy required to determine global buckling loads for fluted-core cylinders. Therefore, it is necessary to develop an analytical method for calculating global buckling loads of fluted-core cylinders that includes transverse-shear deformations, and that can be easily incorporated in preliminary design.
NASA Astrophysics Data System (ADS)
Chue, Ching-Hwei
A method was developed for predicting the behavior of mechanical joints in launch vehicles with particular emphasis placed on how the combined effects of loading, geometry, and materials could be optimized in terms of structure instability and/or integrity. What was considered to be essential is the fluctuation of the volume energy density with time in the structure. The peaks and valleys of the volume energy density function will be associated with failure by fracture and/or yielding while the distance between their local and global stationary values govern the structure instability. The Solid Rocket Booster (SRB) of the space shuttle was analyzed under axisymmetric and non-axisymmetric loadings. A semi-analytical finite element program was developed for solving the case of non-axisymmetric loading. Following a dynamic stress analysis, contours of the volume energy density in the structure were obtained as a function of time. The magnitudes and locations of these stationary values were then calculated locally and globally and related to possible failure by fracture. In the case of axisymmetric flight, the local and global instability behavior do not change appreciably. Fluctuations in the energy density and the dynamic stability length parameter become appreciable when the non-axisymmetric loads are considered. The magnitude of the energy in the shell structure is sensitive to alterations in the gas pressure induced by the solid propellant.
NASA Astrophysics Data System (ADS)
Deng, Liansheng; Jiang, Weiping; Li, Zhao; Chen, Hua; Wang, Kaihua; Ma, Yifang
2017-02-01
Higher-order ionospheric (HOI) delays are one of the principal technique-specific error sources in precise global positioning system analysis and have been proposed to become a standard part of precise GPS data processing. In this research, we apply HOI delay corrections to the Crustal Movement Observation Network of China's (CMONOC) data processing (from January 2000 to December 2013) and furnish quantitative results for the effects of HOI on CMONOC coordinate time series. The results for both a regional reference frame and global reference frame are analyzed and compared to clarify the HOI effects on the CMONOC network. We find that HOI corrections can effectively reduce the semi-annual signals in the northern and vertical components. For sites with lower semi-annual amplitudes, the average decrease in magnitude can reach 30 and 10 % for the northern and vertical components, respectively. The noise amplitudes with HOI corrections and those without HOI corrections are not significantly different. Generally, the HOI effects on CMONOC networks in a global reference frame are less obvious than the results in the regional reference frame, probably because the HOI-induced errors are smaller in comparison to the higher noise levels seen when using a global reference frame. Furthermore, we investigate the combined contributions of environmental loading and HOI effects on the CMONOC stations. The largest loading effects on the vertical displacement are found in the mid- to high-latitude areas. The weighted root mean square differences between the corrected and original weekly GPS height time series of the loading model indicate that the mass loading adequately reduced the scatter on the CMONOC height time series, whereas the results in the global reference frame showed better agreements between the GPS coordinate time series and the environmental loading. When combining the effects of environmental loading and HOI corrections, the results with the HOI corrections reduced the scatter on the observed GPS height coordinates better than the height when estimated without HOI corrections, and the combined solutions in the regional reference frame indicate more preferred improvements. Therefore, regional reference frames are recommended to investigate the HOI effects on regional networks.
The effects of acute stress and perceptual load on distractor interference.
Sato, Hirotsune; Takenaka, Ippei; Kawahara, Jun I
2012-01-01
Selective attention can be improved under conditions in which a high perceptual load is assumed to exhaust cognitive resources, leaving scarce resources for distractor processing. The present study examined whether perceptual load and acute stress share common attentional resources by manipulating perceptual and stress loads. Participants identified a target within an array of nontargets that were flanked by compatible or incompatible distractors. Attentional selectivity was measured by longer reaction times in response to the incompatible than to the compatible distractors. Participants in the stress group participated in a speech test that increased anxiety and threatened self-esteem. The effect of perceptual load interacted with the stress manipulation in that participants in the control group demonstrated an interference effect under the low perceptual load condition, whereas such interference disappeared under the high perceptual load condition. Importantly, the stress group showed virtually no interference under the low perceptual load condition, whereas substantial interference occurred under the high perceptual load condition. These results suggest that perceptual and stress related demands consume the same attentional resources.
Raising Virtual Laboratories in Australia onto global platforms
NASA Astrophysics Data System (ADS)
Wyborn, L. A.; Barker, M.; Fraser, R.; Evans, B. J. K.; Moloney, G.; Proctor, R.; Moise, A. F.; Hamish, H.
2016-12-01
Across the globe, Virtual Laboratories (VLs), Science Gateways (SGs), and Virtual Research Environments (VREs) are being developed that enable users who are not co-located to actively work together at various scales to share data, models, tools, software, workflows, best practices, etc. Outcomes range from enabling `long tail' researchers to more easily access specific data collections, to facilitating complex workflows on powerful supercomputers. In Australia, government funding has facilitated the development of a range of VLs through the National eResearch Collaborative Tools and Resources (NeCTAR) program. The VLs provide highly collaborative, research-domain oriented, integrated software infrastructures that meet user community needs. Twelve VLs have been funded since 2012, including the Virtual Geophysics Laboratory (VGL); Virtual Hazards, Impact and Risk Laboratory (VHIRL); Climate and Weather Science Laboratory (CWSLab); Marine Virtual Laboratory (MarVL); and Biodiversity and Climate Change Virtual Laboratory (BCCVL). These VLs share similar technical challenges, with common issues emerging on integration of tools, applications and access data collections via both cloud-based environments and other distributed resources. While each VL began with a focus on a specific research domain, communities of practice have now formed across the VLs around common issues, and facilitate identification of best practice case studies, and new standards. As a result, tools are now being shared where the VLs access data via data services using international standards such as ISO, OGC, W3C. The sharing of these approaches is starting to facilitate re-usability of infrastructure and is a step towards supporting interdisciplinary research. Whilst the focus of the VLs are Australia-centric, by using standards, these environments are able to be extended to analysis on other international datasets. Many VL datasets are subsets of global datasets and so extension to global is a small (and often requested) step. Similarly, most of the tools, software, and other technologies could be shared across infrastructures globally. Therefore, it is now time to better connect the Australian VLs with similar initiatives elsewhere to create international platforms that can contribute to global research challenges.
PWFQ: a priority-based weighted fair queueing algorithm for the downstream transmission of EPON
NASA Astrophysics Data System (ADS)
Xu, Sunjuan; Ye, Jiajun; Zou, Junni
2005-11-01
In the downstream direction of EPON, all ethernet frames share one downlink channel from the OLT to destination ONUs. To guarantee differentiated services, a scheduling algorithm is needed to solve the link-sharing issue. In this paper, we first review the classical WFQ algorithm and point out the shortcomings existing in the fair queueing principle of WFQ algorithm for EPON. Then we propose a novel scheduling algorithm called Priority-based WFQ (PWFQ) algorithm which distributes bandwidth based on priority. PWFQ algorithm can guarantee the quality of real-time services whether under light load or under heavy load. Simulation results also show that PWFQ algorithm not only can improve delay performance of real-time services, but can also meet the worst-case delay bound requirements.
Generating community-built tools for data sharing and analysis in environmental networks
Read, Jordan S.; Gries, Corinna; Read, Emily K.; Klug, Jennifer; Hanson, Paul C.; Hipsey, Matthew R.; Jennings, Eleanor; O'Reilley, Catherine; Winslow, Luke A.; Pierson, Don; McBride, Christopher G.; Hamilton, David
2016-01-01
Rapid data growth in many environmental sectors has necessitated tools to manage and analyze these data. The development of tools often lags behind the proliferation of data, however, which may slow exploratory opportunities and scientific progress. The Global Lake Ecological Observatory Network (GLEON) collaborative model supports an efficient and comprehensive data–analysis–insight life cycle, including implementations of data quality control checks, statistical calculations/derivations, models, and data visualizations. These tools are community-built and openly shared. We discuss the network structure that enables tool development and a culture of sharing, leading to optimized output from limited resources. Specifically, data sharing and a flat collaborative structure encourage the development of tools that enable scientific insights from these data. Here we provide a cross-section of scientific advances derived from global-scale analyses in GLEON. We document enhancements to science capabilities made possible by the development of analytical tools and highlight opportunities to expand this framework to benefit other environmental networks.
Global Load Balancing with Parallel Mesh Adaption on Distributed-Memory Systems
NASA Technical Reports Server (NTRS)
Biswas, Rupak; Oliker, Leonid; Sohn, Andrew
1996-01-01
Dynamic mesh adaptation on unstructured grids is a powerful tool for efficiently computing unsteady problems to resolve solution features of interest. Unfortunately, this causes load inbalances among processors on a parallel machine. This paper described the parallel implementation of a tetrahedral mesh adaption scheme and a new global load balancing method. A heuristic remapping algorithm is presented that assigns partitions to processors such that the redistribution coast is minimized. Results indicate that the parallel performance of the mesh adaption code depends on the nature of the adaption region and show a 35.5X speedup on 64 processors of an SP2 when 35 percent of the mesh is randomly adapted. For large scale scientific computations, our load balancing strategy gives an almost sixfold reduction in solver execution times over non-balanced loads. Furthermore, our heuristic remappier yields processor assignments that are less than 3 percent of the optimal solutions, but requires only 1 percent of the computational time.
Huang, Cheng-Ya; Chang, Gwo-Ching; Tsai, Yi-Ying; Hwang, Ing-Shiou
2016-01-01
Increase in postural-demand resources does not necessarily degrade a concurrent motor task, according to the adaptive resource-sharing hypothesis of postural-suprapostural dual-tasking. This study investigated how brain networks are organized to optimize a suprapostural motor task when the postural load increases and shifts postural control into a less automatic process. Fourteen volunteers executed a designated force-matching task from a level surface (a relative automatic process in posture) and from a stabilometer board while maintaining balance at a target angle (a relatively controlled process in posture). Task performance of the postural and suprapostural tasks, synchronization likelihood (SL) of scalp EEG, and graph-theoretical metrics were assessed. Behavioral results showed that the accuracy and reaction time of force-matching from a stabilometer board were not affected, despite a significant increase in postural sway. However, force-matching in the stabilometer condition showed greater local and global efficiencies of the brain networks than force-matching in the level-surface condition. Force-matching from a stabilometer board was also associated with greater frontal cluster coefficients, greater mean SL of the frontal and sensorimotor areas, and smaller mean SL of the parietal-occipital cortex than force-matching from a level surface. The contrast of supra-threshold links in the upper alpha and beta bands between the two stance conditions validated load-induced facilitation of inter-regional connections between the frontal and sensorimotor areas, but that contrast also indicated connection suppression between the right frontal-temporal and the parietal-occipital areas for the stabilometer stance condition. In conclusion, an increase in stance difficulty alters the neurocognitive processes in executing a postural-suprapostural task. Suprapostural performance is not degraded by increase in postural load, due to (1) increased effectiveness of information transfer, (2) an anterior shift of processing resources toward frontal executive function, and (3) cortical dissociation of control hubs in the parietal-occipital cortex for neural economy. PMID:27594830
NASA Astrophysics Data System (ADS)
Vilmin, Lauriane; Mogollón, José M.; Beusen, Arthur H. W.; Bouwman, Alexander F.
2018-04-01
Nitrogen (N) and phosphorus (P) play a major role in the biogeochemical functioning of aquatic systems. N and P transfer to surface freshwaters has amplified during the 20th century, which has led to widespread eutrophication problems. The contribution of different sources, natural and anthropogenic, to total N and P loading to river networks has recently been estimated yearly using the Integrated Model to Assess the Global Environment - Global Nutrient Model (IMAGE-GNM). However, eutrophic events generally result from a combination of physicochemical conditions governed by hydrological dynamics and the availability of specific nutrient forms that vary at subyearly timescales. In the present study, we define for each simulated nutrient source: i) its speciation, and ii) its subannual temporal pattern. Thereby, we simulate the monthly loads of different N (ammonium, nitrate + nitrite, and organic N) and P forms (dissolved and particulate inorganic P, and organic P) to global river networks over the whole 20th century at a half-degree spatial resolution. Results indicate that, together with an increase in the delivery of all nutrient forms to global rivers, the proportion of inorganic forms in total N and P inputs has risen from 30 to 43% and from 56 to 65%, respectively. The high loads originating from fertilized agricultural lands and the increasing proportion of sewage inputs have led to a greater proportion of DIN forms (ammonium and nitrate), that are usually more bioavailable. Soil loss from agricultural lands, which delivers large amounts of particle-bound inorganic P to surface freshwaters, has become the dominant P source, which is likely to lead to an increased accumulation of legacy P in slow flowing areas (e.g., lakes and reservoirs). While the TN:TP ratio of the loads has remained quite stable, the DIN:DIP molar ratio, which is likely to affect algal development the most, has increased from 18 to 27 globally. Human activities have also affected the timing of nutrient delivery to surface freshwaters. Increasing wastewater emissions in growing urban areas induces constant local pressure on the quality of aquatic systems by delivering generally highly bioavailable nutrient forms, even in periods of low runoff.
PEPFAR/DOD/Pharmaccess/Tanzania Peoples Defence Forces HIV/AIDS Program
2007-10-01
institutions share many features of a private company, including a hierarchy of functions, investment in training and responsibility for the health status...institutions share many features of a private company, including a hierarchy of functions, investment in training and responsibility for the health...Decks of cards will be distributed to all TPDF Units, Intelligence, Navy and Air Force bases and schools. 2000 Decks will be shared (under the Global
Pratt, Bridget; Hyder, Adnan A
2017-02-01
Global health research partnerships are increasingly taking the form of consortia that conduct programs of research in low and middle-income countries (LMICs). An ethical framework has been developed that describes how the governance of consortia comprised of institutions from high-income countries and LMICs should be structured to promote health equity. It encompasses initial guidance for sharing sovereignty in consortia decision-making and sharing consortia resources. This paper describes a first effort to examine whether and how consortia can uphold that guidance. Case study research was undertaken with the Future Health Systems consortium, performs research to improve health service delivery for the poor in Bangladesh, China, India, and Uganda. Data were thematically analysed and revealed that proposed ethical requirements for sharing sovereignty and sharing resources are largely upheld by Future Health Systems. Facilitating factors included having a decentralised governance model, LMIC partners with good research capacity, and firm budgets. Higher labour costs in the US and UK and the funder's policy of allocating funds to consortia on a reimbursement basis prevented full alignment with guidance on sharing resources. The lessons described in this paper can assist other consortia to more systematically link their governance policy and practice to the promotion of health equity. Copyright © 2016 Elsevier Ltd. All rights reserved.
Vis, D J; Lewin, J; Liao, R G; Mao, M; Andre, F; Ward, R L; Calvo, F; Teh, B T; Camargo, A A; Knoppers, B M; Sawyers, C L; Wessels, L F A; Lawler, M; Siu, L L; Voest, E
2017-05-01
While next generation sequencing has enhanced our understanding of the biological basis of malignancy, current knowledge on global practices for sequencing cancer samples is limited. To address this deficiency, we developed a survey to provide a snapshot of current sequencing activities globally, identify barriers to data sharing and use this information to develop sustainable solutions for the cancer research community. A multi-item survey was conducted assessing demographics, clinical data collection, genomic platforms, privacy/ethics concerns, funding sources and data sharing barriers for sequencing initiatives globally. Additionally, respondents were asked as to provide the primary intent of their initiative (clinical diagnostic, research or combination). Of 107 initiatives invited to participate, 59 responded (response rate = 55%). Whole exome sequencing (P = 0.03) and whole genome sequencing (P = 0.01) were utilized less frequently in clinical diagnostic than in research initiatives. Procedures to identify cancer-specific variants were heterogeneous, with bioinformatics pipelines employing different mutation calling/variant annotation algorithms. Measurement of treatment efficacy varied amongst initiatives, with time on treatment (57%) and RECIST (53%) being the most common; however, other parameters were also employed. Whilst 72% of initiatives indicated data sharing, its scope varied, with a number of restrictions in place (e.g. transfer of raw data). The largest perceived barriers to data harmonization were the lack of financial support (P < 0.01) and bioinformatics concerns (e.g. lack of interoperability) (P = 0.02). Capturing clinical data was more likely to be perceived as a barrier to data sharing by larger initiatives than by smaller initiatives (P = 0.01). These results identify the main barriers, as perceived by the cancer sequencing community, to effective sharing of cancer genomic and clinical data. They highlight the need for greater harmonization of technical, ethical and data capture processes in cancer sample sequencing worldwide, in order to support effective and responsible data sharing for the benefit of patients. © The Author 2017. Published by Oxford University Press on behalf of the European Society for Medical Oncology.
Working memory load modulates the neural response to other's pain: Evidence from an ERP study.
Cui, Fang; Zhu, Xiangru; Luo, Yuejia; Cheng, Jiaping
2017-03-22
The present study investigated the time course of processing other's pain under different conditions of working memory (WM) load. Event-related potentials (ERPs) were recorded while the participants held two digits (low WM load) or six digits (high WM load) in WM and viewed pictures that showed others who were in painful or non-painful situations. Robust WM-load×Picture interactions were found for the N2 and LPP components. In the high WM-load condition, painful pictures elicited significantly larger amplitudes than non-painful pictures. In the low WM load condition, the difference between the painful and non-painful pictures was not significant. These ERP results indicate that WM load can influence both the early automatic N2 component and late cognitive LPP component. Compared with high WM load, low WM load reduced affective arousal and emotional sharing in response to other's pain and weakened the cognitive evaluation of task irrelevant stimuli. These findings are explained from the load theory perspective. Copyright © 2017 Elsevier B.V. All rights reserved.
An Approach and Framework to Synchronize Joint Exercises and Training with Military Operations
2014-06-06
13. SUPPLEMENTARY NOTES 14. ABSTRACT In this dynamic, complex, and uncertain global environment, supporting and conducting joint military...achieved by leveraging a globally networked approach and an integrated framework that shares resources and coordinates activities. A recommended...Intentionally left blank ABSTRACT In this dynamic, complex, and uncertain global environment, supporting and conducting joint military
Kasper, Helmut; Lehrer, Mark; Mühlbacher, Jürgen; Müller, Barbara
2013-02-01
This qualitative field study investigated cross-site knowledge sharing in a small sample of multinational corporations in three different MNC business contexts (global, multidomestic, transnational). The results disclose heterogeneous "worlds" of MNC knowledge sharing, ultimately raising the question as to whether the whole concept of MNC knowledge sharing covers a sufficiently unitary phenomenon to be meaningful. We derive a non-exhaustive typology of MNC knowledge-sharing practices: self-organizing knowledge sharing, technocratic knowledge sharing, and best practice knowledge sharing. Despite its limitations, this typology helps to elucidate a number of issues, including the latent conflict between two disparate theories of MNC knowledge sharing, namely "sender-receiver" and "social learning" theories (Noorderhaven & Harzing, 2009). More generally, we develop the term "knowledge contextualization" to highlight the way that firm-specific organizational features pre-define which knowledge is considered to be of special relevance for intra-organizational sharing.
Liao, Fuyuan; Jan, Yih-Kuen
2012-06-01
This paper presents a recurrence network approach for the analysis of skin blood flow dynamics in response to loading pressure. Recurrence is a fundamental property of many dynamical systems, which can be explored in phase spaces constructed from observational time series. A visualization tool of recurrence analysis called recurrence plot (RP) has been proved to be highly effective to detect transitions in the dynamics of the system. However, it was found that delay embedding can produce spurious structures in RPs. Network-based concepts have been applied for the analysis of nonlinear time series recently. We demonstrate that time series with different types of dynamics exhibit distinct global clustering coefficients and distributions of local clustering coefficients and that the global clustering coefficient is robust to the embedding parameters. We applied the approach to study skin blood flow oscillations (BFO) response to loading pressure. The results showed that global clustering coefficients of BFO significantly decreased in response to loading pressure (p<0.01). Moreover, surrogate tests indicated that such a decrease was associated with a loss of nonlinearity of BFO. Our results suggest that the recurrence network approach can practically quantify the nonlinear dynamics of BFO.
Vergauwe, Evie; Barrouillet, Pierre; Camos, Valérie
2009-07-01
Examinations of interference between visual and spatial materials in working memory have suggested domain- and process-based fractionations of visuo-spatial working memory. The present study examined the role of central time-based resource sharing in visuo-spatial working memory and assessed its role in obtained interference patterns. Visual and spatial storage were combined with both visual and spatial on-line processing components in computer-paced working memory span tasks (Experiment 1) and in a selective interference paradigm (Experiment 2). The cognitive load of the processing components was manipulated to investigate its impact on concurrent maintenance for both within-domain and between-domain combinations of processing and storage components. In contrast to both domain- and process-based fractionations of visuo-spatial working memory, the results revealed that recall performance was determined by the cognitive load induced by the processing of items, rather than by the domain to which those items pertained. These findings are interpreted as evidence for a time-based resource-sharing mechanism in visuo-spatial working memory.
Data sharing in the ag community - what are current challenges, benefits, and opportunities
USDA-ARS?s Scientific Manuscript database
The model for building agronomic science today and into the future to meet global food demands with limited resources will be through public-private data acquisition, sharing, and collaborative analysis. The public perspective focuses on preserving natural resources. The private perspective focuses ...
DISTRIBUTION AND CAUSES OF GLOBAL FOREST FRAGMENTATION
Because human land uses tend to expand over time, forests that share a high proportion of their borders with anthropogenic uses are at higher risk of further degradation than forests that share a high proportion of their borders with non-forest, natural land cover (e.g. wetland)....
Koinonia: The Requirements and Vision for an Unclassified Information-Sharing System
2013-06-01
of an effort to share information with multinational partners in Multinational Planning Augmentation Team (MPAT) ( Tempest Express Fact Sheet 2011... Tempest fact sheet. Global Security.org. May 7, 2011. Accessed May 3, 2013. http://www.globalsecurity.org/military/ops/ tempest -express.htm U.S
Weight and volume variation in truckloads of logs hauled in the central Appalachians
Floyd G. Timson
1974-01-01
Variation in volume and weight was found among loaded log trucks even when such factors as truck type, logging job, and driver influence were eliminated. A load range of 10,000 pounds or 1,000 board feet was commonplace for the same truck, driver, and cutting site. Differences in log size, shape, weight, and species caused a major share of this variation. Yet,...
Design of an Input-Parallel Output-Parallel LLC Resonant DC-DC Converter System for DC Microgrids
NASA Astrophysics Data System (ADS)
Juan, Y. L.; Chen, T. R.; Chang, H. M.; Wei, S. E.
2017-11-01
Compared with the centralized power system, the distributed modularized power system is composed of several power modules with lower power capacity to provide a totally enough power capacity for the load demand. Therefore, the current stress of the power components in each module can then be reduced, and the flexibility of system setup is also enhanced. However, the parallel-connected power modules in the conventional system are usually controlled to equally share the power flow which would result in lower efficiency in low loading condition. In this study, a modular power conversion system for DC micro grid is developed with 48 V dc low voltage input and 380 V dc high voltage output. However, in the developed system control strategy, the numbers of power modules enabled to share the power flow is decided according to the output power at lower load demand. Finally, three 350 W power modules are constructed and parallel-connected to setup a modular power conversion system. From the experimental results, compared with the conventional system, the efficiency of the developed power system in the light loading condition is greatly improved. The modularized design of the power system can also decrease the power loss ratio to the system capacity.
NASA Technical Reports Server (NTRS)
Anderson, N. E.; Cedoz, R. W.; Salama, E. E.; Wagner, D. A.
1987-01-01
An advanced 13,000 HP, counterrotating (CR) gearbox was designed and successfully tested to provide a technology base for future designs of geared propfan propulsion systems for both commercial and military aircraft. The advanced technology CR gearbox was designed for high efficiency, low weight, long life, and improved maintainability. The differential planetary CR gearbox features double helical gears, double row cylindrical roller bearings integral with planet gears, tapered roller prop support bearings, and a flexible ring gear and diaphragm to provide load sharing. A new Allison propfan back-to-back gearbox test facility was constructed. Extensive rotating and stationary instrumentation was used to measure temperature, strain, vibration, deflection and efficiency under representative flight operating conditions. The tests verified smooth, efficient gearbox operation. The highly-instrumented advanced CR gearbox was successfully tested to design speed and power (13,000 HP), and to a 115 percent overspeed condition. Measured CR gearbox efficiency was 99.3 percent at the design point based on heat loss to the oil. Tests demonstrated low vibration characteristics of double helical gearing, proper gear tooth load sharing, low stress levels, and the high load capacity of the prop tapered roller bearings. Applied external prop loads did not significantly affect gearbox temperature, vibration, or stress levels. Gearbox hardware was in excellent condition after the tests with no indication of distress.
Centaur Standard Shroud (CSS) static limit load structural tests
NASA Technical Reports Server (NTRS)
Eastwood, C.
1975-01-01
The structural capabilities of the jettisonable metal shroud were tested and the interaction of the shroud with the Centaur stage was evaluated. A flight-configured shroud and the assemblies of the associated Centaur stage were tested for applied axial and shear loads to flight limit values. The tests included various thermal, pressure, and load conditions to verify localized strength capabilities, to evaluate subsystem performance, and to determine the aging effect on insulation system properties. The tests series verified the strength capabilities of the shroud and of all associated flight assembles. Shroud deflections were shown to remain within allowable limits so long as load sharing members were connected between the shroud and the Centaur stage.
Lairumbi, Geoffrey M; Parker, Michael; Fitzpatrick, Raymond; Mike, English C
2011-10-03
The concept of benefit sharing to enhance the social value of global health research in resource poor settings is now a key strategy for addressing moral issues of relevance to individuals, communities and host countries in resource poor settings when they participate in international collaborative health research.The influence of benefit sharing framework on the conduct of collaborative health research is for instance evidenced by the number of publications and research ethics guidelines that require prior engagement between stakeholders to determine the social value of research to the host communities. While such efforts as the production of international guidance on how to promote the social value of research through such strategies as benefit sharing have been made, the extent to which these ideas and guidelines have been absorbed by those engaged in global health research especially in resource poor settings remains unclear. We examine this awareness among stakeholders involved in health related research in Kenya. We conducted in-depth interviews with key informants drawn from within the broader health research system in Kenya including researchers from the mainstream health research institutions, networks and universities, teaching hospitals, policy makers, institutional review boards, civil society organisations and community representative groups. Our study suggests that although people have a sense of justice and the moral aspects of research, this was not articulated in terms used in the literature and the guidelines on the ethics of global health research. This study demonstrates that while in theory several efforts can be made to address the moral issues of concern to research participants and their communities in resource poor settings, quick fixes such as benefit sharing are not going to be straightforward. We suggest a need to pay closer attention to the processes through which ethical principles are enacted in practice and distil lessons on how best to involve individuals and communities in promoting ethical conduct of global health research in resource poor settings.
2011-01-01
Background The concept of benefit sharing to enhance the social value of global health research in resource poor settings is now a key strategy for addressing moral issues of relevance to individuals, communities and host countries in resource poor settings when they participate in international collaborative health research. The influence of benefit sharing framework on the conduct of collaborative health research is for instance evidenced by the number of publications and research ethics guidelines that require prior engagement between stakeholders to determine the social value of research to the host communities. While such efforts as the production of international guidance on how to promote the social value of research through such strategies as benefit sharing have been made, the extent to which these ideas and guidelines have been absorbed by those engaged in global health research especially in resource poor settings remains unclear. We examine this awareness among stakeholders involved in health related research in Kenya. Methods We conducted in-depth interviews with key informants drawn from within the broader health research system in Kenya including researchers from the mainstream health research institutions, networks and universities, teaching hospitals, policy makers, institutional review boards, civil society organisations and community representative groups. Results Our study suggests that although people have a sense of justice and the moral aspects of research, this was not articulated in terms used in the literature and the guidelines on the ethics of global health research. Conclusion This study demonstrates that while in theory several efforts can be made to address the moral issues of concern to research participants and their communities in resource poor settings, quick fixes such as benefit sharing are not going to be straightforward. We suggest a need to pay closer attention to the processes through which ethical principles are enacted in practice and distil lessons on how best to involve individuals and communities in promoting ethical conduct of global health research in resource poor settings. PMID:21961798
Control of thumb force using surface functional electrical stimulation and muscle load sharing
2013-01-01
Background Stroke survivors often have difficulties in manipulating objects with their affected hand. Thumb control plays an important role in object manipulation. Surface functional electrical stimulation (FES) can assist movement. We aim to control the 2D thumb force by predicting the sum of individual muscle forces, described by a sigmoidal muscle recruitment curve and a single force direction. Methods Five able bodied subjects and five stroke subjects were strapped in a custom built setup. The forces perpendicular to the thumb in response to FES applied to three thumb muscles were measured. We evaluated the feasibility of using recruitment curve based force vector maps in predicting output forces. In addition, we developed a closed loop force controller. Load sharing between the three muscles was used to solve the redundancy problem having three actuators to control forces in two dimensions. The thumb force was controlled towards target forces of 0.5 N and 1.0 N in multiple directions within the individual’s thumb work space. Hereby, the possibilities to use these force vector maps and the load sharing approach in feed forward and feedback force control were explored. Results The force vector prediction of the obtained model had small RMS errors with respect to the actual measured force vectors (0.22±0.17 N for the healthy subjects; 0.17±0.13 N for the stroke subjects). The stroke subjects showed a limited work range due to limited force production of the individual muscles. Performance of feed forward control without feedback, was better in healthy subjects than in stroke subjects. However, when feedback control was added performances were similar between the two groups. Feedback force control lead, especially for the stroke subjects, to a reduction in stationary errors, which improved performance. Conclusions Thumb muscle responses to FES can be described by a single force direction and a sigmoidal recruitment curve. Force in desired direction can be generated through load sharing among redundant muscles. The force vector maps are subject specific and also suitable in feedforward and feedback control taking the individual’s available workspace into account. With feedback, more accurate control of muscle force can be achieved. PMID:24103414
Future energy system challenges for Africa: Insights from Integrated Assessment Models
DOE Office of Scientific and Technical Information (OSTI.GOV)
Lucas, Paul; Nielsen, Jens; Calvin, Katherine V.
Although Africa’s share in the global energy system is only small today, the ongoing population growth and economic development imply that this can change significantly. In this paper, we discuss long-term energy developments in Africa using the results of the LIMITS model inter-comparison study. The analysis focusses on the position of Africa in the wider global energy system and climate mitigation. The results show a considerable spread in model outcomes. Without specific climate policy, Africa’s share in global CO 2 emissions is projected to increase from around 1-4% today to 3-23% by 2100. In all models, emissions only start tomore » become really significant on a global scale after 2050. Furthermore, by 2030 still around 50% of total household energy use is supplied through traditional bio-energy, in contrast to existing ambitions from international organisations to provide access to modern energy for all. After 2050, the energy mix is projected to converge towards a global average energy mix with high shares of fossil fuels and electricity use. Finally, although the continent is now a large net exporter of oil and gas, towards 2050 it most likely needs most of its resources to meet its rapidly growing domestic demand. With respect to climate policy, the rapid expansion of the industrial and the power sector also create large mitigation potential and thereby the possibility to align the investment peak in the energy system with climate policy and potential revenues from international carbon trading.« less
Federal Register 2010, 2011, 2012, 2013, 2014
2012-09-20
... described at www.it.ojp.gov/global . DATES: The meeting will take place on Wednesday, October 24, 2012, from...: This is not a toll-free number]; Email: [email protected]gov . SUPPLEMENTARY INFORMATION: This...
Federal Register 2010, 2011, 2012, 2013, 2014
2013-09-17
... described at www.it.ojp.gov/global . DATES: The meeting will take place on Wednesday, October 30, 2013, from...) 616-0532 [note: this is not a toll-free number]; Email: [email protected]gov . SUPPLEMENTARY...
Global Data Spatially Interrelate System for Scientific Big Data Spatial-Seamless Sharing
NASA Astrophysics Data System (ADS)
Yu, J.; Wu, L.; Yang, Y.; Lei, X.; He, W.
2014-04-01
A good data sharing system with spatial-seamless services will prevent the scientists from tedious, boring, and time consuming work of spatial transformation, and hence encourage the usage of the scientific data, and increase the scientific innovation. Having been adopted as the framework of Earth datasets by Group on Earth Observation (GEO), Earth System Spatial Grid (ESSG) is potential to be the spatial reference of the Earth datasets. Based on the implementation of ESSG, SDOG-ESSG, a data sharing system named global data spatially interrelate system (GASE) was design to make the data sharing spatial-seamless. The architecture of GASE was introduced. The implementation of the two key components, V-Pools, and interrelating engine, and the prototype is presented. Any dataset is firstly resampled into SDOG-ESSG, and is divided into small blocks, and then are mapped into hierarchical system of the distributed file system in V-Pools, which together makes the data serving at a uniform spatial reference and at a high efficiency. Besides, the datasets from different data centres are interrelated by the interrelating engine at the uniform spatial reference of SDOGESSG, which enables the system to sharing the open datasets in the internet spatial-seamless.
CaLRS: A Critical-Aware Shared LLC Request Scheduling Algorithm on GPGPU
Ma, Jianliang; Meng, Jinglei; Chen, Tianzhou; Wu, Minghui
2015-01-01
Ultra high thread-level parallelism in modern GPUs usually introduces numerous memory requests simultaneously. So there are always plenty of memory requests waiting at each bank of the shared LLC (L2 in this paper) and global memory. For global memory, various schedulers have already been developed to adjust the request sequence. But we find few work has ever focused on the service sequence on the shared LLC. We measured that a big number of GPU applications always queue at LLC bank for services, which provide opportunity to optimize the service order on LLC. Through adjusting the GPU memory request service order, we can improve the schedulability of SM. So we proposed a critical-aware shared LLC request scheduling algorithm (CaLRS) in this paper. The priority representative of memory request is critical for CaLRS. We use the number of memory requests that originate from the same warp but have not been serviced when they arrive at the shared LLC bank to represent the criticality of each warp. Experiments show that the proposed scheme can boost the SM schedulability effectively by promoting the scheduling priority of the memory requests with high criticality and improves the performance of GPU indirectly. PMID:25729772
NASA Astrophysics Data System (ADS)
Domino, Krzysztof
2012-01-01
The WIG20 index-the index of the 20 biggest companies traded on the Warsaw Stock Exchange-reached the global maximum on 29th October 2007. I have used the local DFA (Detrended Functional Analysis) to obtain the Hurst exponent (diffusion exponent) and investigate the signature of anti-correlation of share price evolution around the maximum. The analysis was applied to the share price evolution for variable DFA parameters. For many values of parameters, the evidence of anti-correlation near the WIG20 maximum was pointed out.
Modeling and assessing international climate financing
NASA Astrophysics Data System (ADS)
Wu, Jing; Tang, Lichun; Mohamed, Rayman; Zhu, Qianting; Wang, Zheng
2016-06-01
Climate financing is a key issue in current negotiations on climate protection. This study establishes a climate financing model based on a mechanism in which donor countries set up funds for climate financing and recipient countries use the funds exclusively for carbon emission reduction. The burden-sharing principles are based on GDP, historical emissions, and consumptionbased emissions. Using this model, we develop and analyze a series of scenario simulations, including a financing program negotiated at the Cancun Climate Change Conference (2010) and several subsequent programs. Results show that sustained climate financing can help to combat global climate change. However, the Cancun Agreements are projected to result in a reduction of only 0.01°C in global warming by 2100 compared to the scenario without climate financing. Longer-term climate financing programs should be established to achieve more significant benefits. Our model and simulations also show that climate financing has economic benefits for developing countries. Developed countries will suffer a slight GDP loss in the early stages of climate financing, but the longterm economic growth and the eventual benefits of climate mitigation will compensate for this slight loss. Different burden-sharing principles have very similar effects on global temperature change and economic growth of recipient countries, but they do result in differences in GDP changes for Japan and the FSU. The GDP-based principle results in a larger share of financial burden for Japan, while the historical emissions-based principle results in a larger share of financial burden for the FSU. A larger burden share leads to a greater GDP loss.
Graduating to Postdoc: Information-Sharing in Support of Organizational Structures and Needs
NASA Technical Reports Server (NTRS)
Keller, Richard M.; Lucas, Paul J.; Compton, Michael M.; Stewart, Helen J.; Baya, Vinod; DelAlto, Martha
1999-01-01
The deployment of information-sharing systems in large organizations can significantly impact existing policies and procedures with regard to authority and control over information. Unless information-sharing systems explicitly support organizational structures and needs, these systems will be rejected summarily. The Postdoc system is a deployed Web-based information-sharing system created specifically to address organizational needs. Postdoc contains various organizational support features including a shared, globally navigable document space, as well as specialized access control, distributed administration, and mailing list features built around the key notion of hierarchical group structures. We review successes and difficulties in supporting organizational needs with Postdoc
Galy, Edith; Paxion, Julie; Berthelon, Catherine
2018-04-01
The distinction between several components of mental workload is often made in the ergonomics literature. However, measurements used are often established from a global score, notably with several questionnaires that originally reflect several dimensions. The present study tested the effect of driving situation complexity, experience and subjective levels of tension and alertness on each dimension of the NASA-TLX questionnaire of workload, in order to highlight the potential influence of intrinsic, extraneous and germane load factors. The results showed that, in complex situation, mental, temporal and physical demand (load dimensions) increased, and that novice drivers presented high physical demand when subjective tension was low on performance. Moreover, increase of mental and physical demand increased effort. It thus, appears essential to distinguish the different components of mental workload used in the NASA-TLX questionnaire. Practitioner Summary: Currently, global score of NASA-TLX questionnaire is used to measure mental workload. Here, we considered independently each dimension of NASA-TLX, and results showed that mental load factors (driving situation complexity, experience, subjective tension and alertness) had a different effect on dimensions, questioning global score use to evaluate workload.
Global and Local Stress Analyses of McDonnell Douglas Stitched/RFI Composite Wing Stub Box
NASA Technical Reports Server (NTRS)
Wang, John T.
1996-01-01
This report contains results of structural analyses performed in support of the NASA structural testing of an all-composite stitched/RFI (resin film infusion) wing stub box. McDonnell Douglas Aerospace Company designed and fabricated the wing stub box. The analyses used a global/local approach. The global model contains the entire test article. It includes the all-composite stub box, a metallic load-transition box and a metallic wing-tip extension box. The two metallic boxes are connected to the inboard and outboard ends of the composite wing stub box, respectively. The load-transition box was attached to a steel and concrete vertical reaction structure and a load was applied at the tip of the extension box to bend the wing stub box upward. The local model contains an upper cover region surrounding three stringer runouts. In that region, a large nonlinear deformation was identified by the global analyses. A more detailed mesh was used for the local model to obtain more accurate analysis results near stringer runouts. Numerous analysis results such as deformed shapes, displacements at selected locations, and strains at critical locations are included in this report.
Globalizing Lessons Learned from Regional-scale Observatories
NASA Astrophysics Data System (ADS)
Glenn, S. M.
2016-02-01
The Mid Atlantic Regional Association Coastal Ocean Observing System (MARACOOS) has accumulated a decade of experience designing, building and operating a Regional Coastal Ocean Observing System for the U.S. Integrated Ocean Observing System (IOOS). MARACOOS serves societal goals and supports scientific discovery at the scale of a Large Marine Ecosystem (LME). Societal themes include maritime safety, ecosystem decision support, coastal inundation, water quality and offshore energy. Scientific results that feed back on societal goals with better products include improved understanding of seasonal transport pathways and their impact on phytoplankton blooms and hypoxia, seasonal evolution of the subsurface Mid Atlantic Cold Pool and its impact on fisheries, biogeochemical transformations in coastal plumes, coastal ocean evolution and impact on hurricane intensities, and storm sediment transport pathways. As the global ocean observing requirements grow to support additional societal needs for information on fisheries and aquaculture, ocean acidification and deoxygenation, water quality and offshore development, global observing will necessarily evolve to include more coastal observations and forecast models at the scale of the world's many LMEs. Here we describe our efforts to share lessons learned between the observatory operators at the regional-scale of the LMEs. Current collaborators are spread across Europe, and also include Korea, Indonesia, Australia, Brazil and South Africa. Specific examples include the development of a world standard QA/QC approach for HF Radar data that will foster the sharing of data between countries, basin-scale underwater glider missions between internationally-distributed glider ports to developed a shared understanding of operations and an ongoing evaluation of the global ocean models in which the regional models for the LME will be nested, and joint training programs to develop the distributed teams of scientists and technicians required to support the global network. Globalization includes the development of international networks to coordinate activities, such as the Global HF Radar network supported by GEO, the global Everyone's Glider Organization supported by WMO and IOC, and the need for professional training supported by MTS.
Learning to Share: Australia's "Building the Education Revolution" and Shared Schools
ERIC Educational Resources Information Center
McShane, Ian
2012-01-01
This article analyses the conceptual and policy contexts of the Australian government's "Building the Education Revolution" (BER) programme. This $A15 billion commitment to renewing school facilities is the Australian government's largest single measure of economic stimulus in response to the recent global financial crisis. Public debate…
Telling War Stories: The Things They Carry
ERIC Educational Resources Information Center
Paquette, Paige; Warren, Mike
2010-01-01
This webtext reveals two modern-day methods for soldiers to share their war stories: 1) soldiers sharing their stories with cadets from West Point through a project linking veterans from the Global War on Terror with composition students; and 2) soldiers learning in online composition classrooms designed specifically for them.
Voices of Women in the Field: Laundry and Leadership--A New Dance
ERIC Educational Resources Information Center
Curley, Ginny
2007-01-01
In this article, the author shares a story of a young couple who was arguing about the proper way to fold towels. The husband shared a story of how he had wanted to do something nice for his wife, who was studying. So he folded a load of towels and put them away. His wife then refolded the towels, explaining that he had folded them in half and…
Time-dependent fiber bundles with local load sharing. II. General Weibull fibers.
Phoenix, S Leigh; Newman, William I
2009-12-01
Fiber bundle models (FBMs) are useful tools in understanding failure processes in a variety of material systems. While the fibers and load sharing assumptions are easily described, FBM analysis is typically difficult. Monte Carlo methods are also hampered by the severe computational demands of large bundle sizes, which overwhelm just as behavior relevant to real materials starts to emerge. For large size scales, interest continues in idealized FBMs that assume either equal load sharing (ELS) or local load sharing (LLS) among fibers, rules that reflect features of real load redistribution in elastic lattices. The present work focuses on a one-dimensional bundle of N fibers under LLS where life consumption in a fiber follows a power law in its load, with exponent rho , and integrated over time. This life consumption function is further embodied in a functional form resulting in a Weibull distribution for lifetime under constant fiber stress and with Weibull exponent, beta. Thus the failure rate of a fiber depends on its past load history, except for beta=1 . We develop asymptotic results validated by Monte Carlo simulation using a computational algorithm developed in our previous work [Phys. Rev. E 63, 021507 (2001)] that greatly increases the size, N , of treatable bundles (e.g., 10(6) fibers in 10(3) realizations). In particular, our algorithm is O(N ln N) in contrast with former algorithms which were O(N2) making this investigation possible. Regimes are found for (beta,rho) pairs that yield contrasting behavior for large N. For rho>1 and large N, brittle weakest volume behavior emerges in terms of characteristic elements (groupings of fibers) derived from critical cluster formation, and the lifetime eventually goes to zero as N-->infinity , unlike ELS, which yields a finite limiting mean. For 1/2
Time-dependent fiber bundles with local load sharing. II. General Weibull fibers
NASA Astrophysics Data System (ADS)
Phoenix, S. Leigh; Newman, William I.
2009-12-01
Fiber bundle models (FBMs) are useful tools in understanding failure processes in a variety of material systems. While the fibers and load sharing assumptions are easily described, FBM analysis is typically difficult. Monte Carlo methods are also hampered by the severe computational demands of large bundle sizes, which overwhelm just as behavior relevant to real materials starts to emerge. For large size scales, interest continues in idealized FBMs that assume either equal load sharing (ELS) or local load sharing (LLS) among fibers, rules that reflect features of real load redistribution in elastic lattices. The present work focuses on a one-dimensional bundle of N fibers under LLS where life consumption in a fiber follows a power law in its load, with exponent ρ , and integrated over time. This life consumption function is further embodied in a functional form resulting in a Weibull distribution for lifetime under constant fiber stress and with Weibull exponent, β . Thus the failure rate of a fiber depends on its past load history, except for β=1 . We develop asymptotic results validated by Monte Carlo simulation using a computational algorithm developed in our previous work [Phys. Rev. EPLEEE81063-651X 63, 021507 (2001)] that greatly increases the size, N , of treatable bundles (e.g., 106 fibers in 103 realizations). In particular, our algorithm is O(NlnN) in contrast with former algorithms which were O(N2) making this investigation possible. Regimes are found for (β,ρ) pairs that yield contrasting behavior for large N . For ρ>1 and large N , brittle weakest volume behavior emerges in terms of characteristic elements (groupings of fibers) derived from critical cluster formation, and the lifetime eventually goes to zero as N→∞ , unlike ELS, which yields a finite limiting mean. For 1/2≤ρ≤1 , however, LLS has remarkably similar behavior to ELS (appearing to be virtually identical for ρ=1 ) with an asymptotic Gaussian lifetime distribution and a finite limiting mean for large N . The coefficient of variation follows a power law in increasing N but, except for ρ=1 , the value of the negative exponent is clearly less than 1/2 unlike in ELS bundles where the exponent remains 1/2 for 1/2<ρ≤1 . For sufficiently small values 0<ρ≪1 , a transition occurs, depending on β , whereby LLS bundle lifetimes become dominated by a few long-lived fibers. Thus the bundle lifetime appears to approximately follow an extreme-value distribution for the longest lived of a parallel group of independent elements, which applies exactly to ρ=0 . The lower the value of β , the higher the transition value of ρ , below which such extreme-value behavior occurs. No evidence was found for limiting Gaussian behavior for ρ>1 but with 0<β(ρ+1)<1 , as might be conjectured from quasistatic bundle models where β(ρ+1) mimics the Weibull exponent for fiber strength.
Design Evaluation of Wind Turbine Spline Couplings Using an Analytical Model: Preprint
DOE Office of Scientific and Technical Information (OSTI.GOV)
Guo, Y.; Keller, J.; Wallen, R.
2015-02-01
Articulated splines are commonly used in the planetary stage of wind turbine gearboxes for transmitting the driving torque and improving load sharing. Direct measurement of spline loads and performance is extremely challenging because of limited accessibility. This paper presents an analytical model for the analysis of articulated spline coupling designs. For a given torque and shaft misalignment, this analytical model quickly yields insights into relationships between the spline design parameters and resulting loads; bending, contact, and shear stresses; and safety factors considering various heat treatment methods. Comparisons of this analytical model against previously published computational approaches are also presented.
Sustaining the Civil Reserve Air Fleet (CRAF) Program
2003-05-01
means to build international networks and global marketing alliances. These arrangements have permitted alliances to exploit the regional competitive...next major phase occurred in the 1990s—the linking of networks in different countries through code sharing alliances and global marketing alliances
Stern, Rachel J; Fernandez, Alicia; Jacobs, Elizabeth A; Neilands, Torsten B; Weech-Maldonado, Robert; Quan, Judy; Carle, Adam; Seligman, Hilary K
2012-09-01
Providing culturally competent care shows promise as a mechanism to reduce health care inequalities. Until the recent development of the Consumer Assessment of Healthcare Providers and Systems Cultural Competency Item Set (CAHPS-CC), no measures capturing patient-level experiences with culturally competent care have been suitable for broad-scale administration. We performed confirmatory factor analysis and internal consistency reliability analysis of CAHPS-CC among patients with type 2 diabetes (n=600) receiving primary care in safety-net clinics. CAHPS-CC domains were also correlated with global physician ratings. A 7-factor model demonstrated satisfactory fit (χ²₂₃₁=484.34, P<0.0001) with significant factor loadings at P<0.05. Three domains showed excellent reliability-Doctor Communication-Positive Behaviors (α=0.82), Trust (α=0.77), and Doctor Communication-Health Promotion (α=0.72). Four domains showed inadequate reliability either among Spanish speakers or overall (overall reliabilities listed): Doctor Communication-Negative Behaviors (α=0.54), Equitable Treatment (α=0.69), Doctor Communication-Alternative Medicine (α=0.52), and Shared Decision-Making (α=0.51). CAHPS-CC domains were positively and significantly correlated with global physician rating. Select CAHPS-CC domains are suitable for broad-scale administration among safety-net patients. Those domains may be used to target quality-improvement efforts focused on providing culturally competent care in safety-net settings.
Tuition Fees and Student Financial Assistance: 2010 Global Year
ERIC Educational Resources Information Center
Marcucci, Pamela; Usher, Alex
2011-01-01
Since the start of the global financial crisis a little over two years ago, many concerns have been raised on how it might affect funding to higher education and whether or not it might hasten moves toward greater cost sharing. While, globally, some steps have been taken in this direction, in most countries, hard decisions have yet to be taken on…
ERIC Educational Resources Information Center
Cheon, Jongpil; Lee, Sangno; Smith, Walter; Song, Jaeki; Kim, Yongjin
2013-01-01
The purpose of this study was to use text mining analysis of early adolescents' online essays to determine their knowledge of global lunar patterns. Australian and American students in grades five to seven wrote about global lunar patterns they had discovered by sharing observations with each other via the Internet. These essays were analyzed for…
Linda L. Langner; Peter J. Ince
2012-01-01
The Resources Planning Act (RPA) Assessment provides a nationally consistent analysis of the status and trends of the Nation's renewable forest resources. A global scenario approach was taken for the 2010 RPA Assessment to provide a shared world view of potential futures. The RPA Assessment scenarios were linked to the global scenarios and climate projections used...
Globalization in the One World: Impacts on Education in Different Nations
ERIC Educational Resources Information Center
Pang, Nicholas Sun-keung
2013-01-01
There is only one world, but it is widely divided. All nations share a common interest in the investment and development of education in their own contexts. The one world has been undergoing tremendous, turbulent changes, due to the recent quick movement in globalization. This paper aims to explore what is meant by globalization, how it has…
Why Are Drugs So Hard to Quit?
... Loading... Close Yeah, keep it Undo Close This video is unavailable. Watch Queue Queue Watch Queue Queue ... in Share More Report Need to report the video? Sign in to report inappropriate content. Sign in ...
Pletzer, Belinda; Scheuringer, Andrea; Scherndl, Thomas
2017-09-05
Sex differences have been reported for a variety of cognitive tasks and related to the use of different cognitive processing styles in men and women. It was recently argued that these processing styles share some characteristics across tasks, i.e. male approaches are oriented towards holistic stimulus aspects and female approaches are oriented towards stimulus details. In that respect, sex-dependent cognitive processing styles share similarities with attentional global-local processing. A direct relationship between cognitive processing and global-local processing has however not been previously established. In the present study, 49 men and 44 women completed a Navon paradigm and a Kimchi Palmer task as well as a navigation task and a verbal fluency task with the goal to relate the global advantage (GA) effect as a measure of global processing to holistic processing styles in both tasks. Indeed participants with larger GA effects displayed more holistic processing during spatial navigation and phonemic fluency. However, the relationship to cognitive processing styles was modulated by the specific condition of the Navon paradigm, as well as the sex of participants. Thus, different types of global-local processing play different roles for cognitive processing in men and women.
Prediction-based dynamic load-sharing heuristics
NASA Technical Reports Server (NTRS)
Goswami, Kumar K.; Devarakonda, Murthy; Iyer, Ravishankar K.
1993-01-01
The authors present dynamic load-sharing heuristics that use predicted resource requirements of processes to manage workloads in a distributed system. A previously developed statistical pattern-recognition method is employed for resource prediction. While nonprediction-based heuristics depend on a rapidly changing system status, the new heuristics depend on slowly changing program resource usage patterns. Furthermore, prediction-based heuristics can be more effective since they use future requirements rather than just the current system state. Four prediction-based heuristics, two centralized and two distributed, are presented. Using trace driven simulations, they are compared against random scheduling and two effective nonprediction based heuristics. Results show that the prediction-based centralized heuristics achieve up to 30 percent better response times than the nonprediction centralized heuristic, and that the prediction-based distributed heuristics achieve up to 50 percent improvements relative to their nonprediction counterpart.
Flight Testing of the Capillary Pumped Loop 3 Experiment
NASA Technical Reports Server (NTRS)
Ottenstein, Laura; Butler, Dan; Ku, Jentung; Cheung, Kwok; Baldauff, Robert; Hoang, Triem
2002-01-01
The Capillary Pumped Loop 3 (CAPL 3) experiment was a multiple evaporator capillary pumped loop experiment that flew in the Space Shuttle payload bay in December 2001 (STS-108). The main objective of CAPL 3 was to demonstrate in micro-gravity a multiple evaporator capillary pumped loop system, capable of reliable start-up, reliable continuous operation, and heat load sharing, with hardware for a deployable radiator. Tests performed on orbit included start-ups, power cycles, low power tests (100 W total), high power tests (up to 1447 W total), heat load sharing, variable/fixed conductance transition tests, and saturation temperature change tests. The majority of the tests were completed successfully, although the experiment did exhibit an unexpected sensitivity to shuttle maneuvers. This paper describes the experiment, the tests performed during the mission, and the test results.
A Review of Distributed Control Techniques for Power Quality Improvement in Micro-grids
NASA Astrophysics Data System (ADS)
Zeeshan, Hafiz Muhammad Ali; Nisar, Fatima; Hassan, Ahmad
2017-05-01
Micro-grid is typically visualized as a small scale local power supply network dependent on distributed energy resources (DERs) that can operate simultaneously with grid as well as in standalone manner. The distributed generator of a micro-grid system is usually a converter-inverter type topology acting as a non-linear load, and injecting harmonics into the distribution feeder. Hence, the negative effects on power quality by the usage of distributed generation sources and components are clearly witnessed. In this paper, a review of distributed control approaches for power quality improvement is presented which encompasses harmonic compensation, loss mitigation and optimum power sharing in multi-source-load distributed power network. The decentralized subsystems for harmonic compensation and active-reactive power sharing accuracy have been analysed in detail. Results have been validated to be consistent with IEEE standards.
Wahn, Basil; König, Peter
2015-01-01
Humans continuously receive and integrate information from several sensory modalities. However, attentional resources limit the amount of information that can be processed. It is not yet clear how attentional resources and multisensory processing are interrelated. Specifically, the following questions arise: (1) Are there distinct spatial attentional resources for each sensory modality? and (2) Does attentional load affect multisensory integration? We investigated these questions using a dual task paradigm: participants performed two spatial tasks (a multiple object tracking task and a localization task), either separately (single task condition) or simultaneously (dual task condition). In the multiple object tracking task, participants visually tracked a small subset of several randomly moving objects. In the localization task, participants received either visual, auditory, or redundant visual and auditory location cues. In the dual task condition, we found a substantial decrease in participants' performance relative to the results of the single task condition. Importantly, participants performed equally well in the dual task condition regardless of the location cues' modality. This result suggests that having spatial information coming from different modalities does not facilitate performance, thereby indicating shared spatial attentional resources for the auditory and visual modality. Furthermore, we found that participants integrated redundant multisensory information similarly even when they experienced additional attentional load in the dual task condition. Overall, findings suggest that (1) visual and auditory spatial attentional resources are shared and that (2) audiovisual integration of spatial information occurs in an pre-attentive processing stage.
Estimation of global plastic loads delivered by rivers into the sea
NASA Astrophysics Data System (ADS)
Schmidt, Christian; Krauth, Tobias; Klöckner, Phillipp; Römer, Melina-Sophie; Stier, Britta; Reemtsma, Thorsten; Wagner, Stephan
2017-04-01
A considerable fraction of marine plastic debris likely originates from land-based sources. Transport of plastics by rivers is a potential mechanism that connects plastic debris generated on land with the marine environment. We analyze existing and experimental data of plastic loads in rivers and relate these to the amount of mismanaged plastic waste (MMPW) generated in the river catchments. We find a positive relationship between the plastic load in rivers and the amount of MMPW. Using our empirical MMPW-plastic river load-relationship we estimated the annual plastic load for 1494 rivers, ranging from small first order streams to large rivers, which have an outlet to the sea. We estimate that the global load of plastic debris delivered by rivers to the sea is 39000 tons per year with a large 95% prediction interval between 247 tons per year and 16.7 million tons per year, respectively. Our best estimate is considerably lower than the estimated total land-based inputs which range between 4.8-12.7 million tons anually (Jambeck et al. 2015). Approximately 75% of the total load is transported by the 10 top-ranked rivers which are predominantly located in Asia. These river catchments encompass countries with a large population and high economic growth but an insufficient waste infrastructure. Reducing the plastic loads in these rivers by 50% would reduce the global inputs by 37%. Of the total MMPW generated within river catchments, only a small fraction of about 0.05 % has been found to be mobile in rivers. Thus, either only a small fraction of MMPW enters the river systems, or a substantial fraction of plastic debris accumulates in river systems world wide. References: Jambeck, J. R., R. Geyer, C. Wilcox, T. R. Siegler, M. Perryman, A. Andrady, R. Narayan, and K. L. Law (2015), Plastic waste inputs from land into the ocean, Science, 347(6223), 768-771, doi:10.1126/science.1260352.
NASA Astrophysics Data System (ADS)
Zhang, B.; Brambles, O. J.; Cassak, P. A.; Ouellette, J. E.; Wiltberger, M.; Lotko, W.; Lyon, J. G.
2017-09-01
We have conducted a series of controlled numerical simulations to investigate the response of dayside reconnection to idealized, ionosphere-sourced mass loading processes to determine whether they affect the integrated dayside reconnection rate. Our simulation results show that the coupled solar wind-magnetosphere system may exhibit both local and global control behaviors depending on the amount of mass loading. With a small amount of mass loading, the changes in local reconnection rate affects magnetosheath properties only weakly and the geoeffective length in the upstream solar wind is essentially unchanged, resulting in the same integrated dayside reconnection rate. With a large amount of mass loading, however, the magnetosheath properties and the geoeffective length are significantly affected by slowing down the local reconnection rate, resulting in an increase of the magnetic pressure in the magnetosheath, with a significant reduction in the geoeffective length in the upstream solar wind and in the integrated dayside reconnection rate. In this controlled simulation setup, the behavior of dayside reconnection potential is determined by the role of the enhanced magnetic pressure in the magnetospheath due to magnetospheric mass loading. The reconnection potential starts to decrease significantly when the enhanced magnetic pressure alters the thickness of the magnetosheath.
NASA Astrophysics Data System (ADS)
Engström, Kerstin; Olin, Stefan; Rounsevell, Mark D. A.; Brogaard, Sara; van Vuuren, Detlef P.; Alexander, Peter; Murray-Rust, Dave; Arneth, Almut
2016-11-01
We present a modelling framework to simulate probabilistic futures of global cropland areas that are conditional on the SSP (shared socio-economic pathway) scenarios. Simulations are based on the Parsimonious Land Use Model (PLUM) linked with the global dynamic vegetation model LPJ-GUESS (Lund-Potsdam-Jena General Ecosystem Simulator) using socio-economic data from the SSPs and climate data from the RCPs (representative concentration pathways). The simulated range of global cropland is 893-2380 Mha in 2100 (± 1 standard deviation), with the main uncertainties arising from differences in the socio-economic conditions prescribed by the SSP scenarios and the assumptions that underpin the translation of qualitative SSP storylines into quantitative model input parameters. Uncertainties in the assumptions for population growth, technological change and cropland degradation were found to be the most important for global cropland, while uncertainty in food consumption had less influence on the results. The uncertainties arising from climate variability and the differences between climate change scenarios do not strongly affect the range of global cropland futures. Some overlap occurred across all of the conditional probabilistic futures, except for those based on SSP3. We conclude that completely different socio-economic and climate change futures, although sharing low to medium population development, can result in very similar cropland areas on the aggregated global scale.
1982-02-01
EXPERIMENTAL EVIDENCE ...... ....... ....... ....... ... 27 2.6 LOAD REDISTRIBUTION DUE TO DISBONDS IN ADHESIVE IN STEPPED-LAP JOINTS...SINGLE FASTENER " . ;39 3.4 LOAD SHARING BETWEEN MULTIRUW FASTENERS.."."..-.."." ൴ 3.5 FAILURE CRITERIA AT FASTENER HOLES . . ... 3.6 EXPERIMENTAL ...PLASTIC C. PERFECTLY ELASTIC THROUGHOUT A. ULL PLSTC SEAR TRS•WITHOUT $1IGN REVERSAL WITHOUT S:IG13 REVERSAL IOR FULLY NEGATIVE QUIVALENT ) (OR FULLY
GPS-Only Terrestrial Reference Frame Based on a Global Reprocessing
NASA Astrophysics Data System (ADS)
Dietrich, R.; Rothacher, M.; Ruelke, A.; Fritsche, M.; Steigenberger, P.
2007-12-01
The realization of the International Terrestrial Reference System (ITRS) with highest accuracy and stability is fundamental and crucial for applications in geodesy, geodynamics, geophysics and global change. In a joint effort TU Dresden and TU Munich/GFZ Potsdam reprocessed a global GPS network of more than 200 stations. As a contribution to an ITRS realization daily normal equations from 1994 to 2005 were rigorously combined in order to determine a global GPS-only reference frame (PDR05/Potsdam-Dresden-Reprocessing Reference Frame). We present a realization of the global terrestrial reference system which follows the center of mass approach in consideration of the load-induced deformation of the Earth's crust due to the redistribution of surface masses. The stability of our reference frame will be evaluated based on the obtained long-term trends of station coordinates, the load-induced deformation estimates and the homogeneous time series of station positions. We will compare our solution with other recent terrestrial reference system realizations and give some conclusions for future realizations of the ITRS.
Running a network on a shoestring: the Global Invasive Species Information Network
Jarnevich, Catherine S.; Simpson, Annie; Graham, James J; Newman, Gregory J.; Bargeron, Chuck T.
2015-01-01
The Global Invasive Species Information Network (GISIN) was conceptualized in 2004 to aggregate and disseminate invasive species data in a standardized way. A decade later the GISIN community has implemented a data portal and three of six GISIN data aggregation models in the GISIN data exchange Protocol, including invasive species status information, resource URLs, and occurrence data. The portal is based on a protocol developed by representatives from 15 countries and 27 organizations of the global invasive species information management community. The GISIN has 19 data providers sharing 34,343 species status records, 1,693,073 occurrences, and 15,601 resource URLs. While the GISIN's goal is to be global, much of its data and funding are provided by the United States. Several initiatives use the GISIN as their information backbone, such as the Great Lakes Early Detection Network (GLEDN) and the North American Invasive Species Network (NAISN). Here we share several success stories and organizational challenges that remain.
The Currency of Consciousness: Neurology, Specialization, and the Global Practices of Medicine.
Casper, Stephen T
2016-01-01
This article explores the formation of a global community of neurologists between 1918 and 1970. Relying chiefly upon documents located in Anglo-American archives, its argument follows a narrative from money to memory, and posits that this global community of neurologists formed not out of a shared science and medicine of the nervous system, but out of shared dispositions in tastes, values, and culture. The localism and heterogeneity of the science and medicine of the nervous system was in fact so pronounced that neurologists - especially when they worked as "global citizens" - were forced to focus upon their superficial commonalities rather than examine local distinctions. This avoidance of a direct effort to define the content of neurology - or at least to confront their differences - exercised a peculiar influence on the specialty. Neurologists and their "official memory" became negotiated, and even imagined constructs. Consequently, these diverse cultures were ultimately subordinated to dominant economic interests.
Bala, Adarsh; Gupta, B M
2010-01-01
This study analyses the research output in India in neurosciences during the period 1999-2008 and the analyses included research growth, rank, global publications' share, citation impact, share of international collaborative papers and major collaborative partner countries and patterns of research communication in most productive journals. It also analyses the characteristics of most productive institutions, authors and high-cited papers. The publication output and impact of India is also compared with China, Brazil and South Korea. Scopus Citation database was used for retrieving the publications' output of India and other countries in neurosciences during 1999-2008. India's global publications' share in neurosciences during the study period was 0.99% (with 4503 papers) and it ranked 21 st among the top 26 countries in neurosciences. The average annual publication growth rate was 11.37%, shared 17.34% of international collaborative papers and the average citation per paper was 4.21. India was far behind China, Brazil and South Korea in terms of publication output, citation quality and share of international collaborative papers in neurosciences. India is far behind in terms of publication output, citation quality and share of international collaborative papers in neurosciences when compared to other countries with an emerging economy. There is an urgent need to substantially increase the research activities in the field of neurosciences in India.
Network Computing Infrastructure to Share Tools and Data in Global Nuclear Energy Partnership
NASA Astrophysics Data System (ADS)
Kim, Guehee; Suzuki, Yoshio; Teshima, Naoya
CCSE/JAEA (Center for Computational Science and e-Systems/Japan Atomic Energy Agency) integrated a prototype system of a network computing infrastructure for sharing tools and data to support the U.S. and Japan collaboration in GNEP (Global Nuclear Energy Partnership). We focused on three technical issues to apply our information process infrastructure, which are accessibility, security, and usability. In designing the prototype system, we integrated and improved both network and Web technologies. For the accessibility issue, we adopted SSL-VPN (Security Socket Layer-Virtual Private Network) technology for the access beyond firewalls. For the security issue, we developed an authentication gateway based on the PKI (Public Key Infrastructure) authentication mechanism to strengthen the security. Also, we set fine access control policy to shared tools and data and used shared key based encryption method to protect tools and data against leakage to third parties. For the usability issue, we chose Web browsers as user interface and developed Web application to provide functions to support sharing tools and data. By using WebDAV (Web-based Distributed Authoring and Versioning) function, users can manipulate shared tools and data through the Windows-like folder environment. We implemented the prototype system in Grid infrastructure for atomic energy research: AEGIS (Atomic Energy Grid Infrastructure) developed by CCSE/JAEA. The prototype system was applied for the trial use in the first period of GNEP.
Direct access inter-process shared memory
Brightwell, Ronald B; Pedretti, Kevin; Hudson, Trammell B
2013-10-22
A technique for directly sharing physical memory between processes executing on processor cores is described. The technique includes loading a plurality of processes into the physical memory for execution on a corresponding plurality of processor cores sharing the physical memory. An address space is mapped to each of the processes by populating a first entry in a top level virtual address table for each of the processes. The address space of each of the processes is cross-mapped into each of the processes by populating one or more subsequent entries of the top level virtual address table with the first entry in the top level virtual address table from other processes.
Modeling particulate matter emissions during mineral loading process under weak wind simulation.
Zhang, Xiaochun; Chen, Weiping; Ma, Chun; Zhan, Shuifen
2013-04-01
The quantification of particulate matter emissions from mineral handling is an important problem for the quantification of global emissions on industrial sites. Mineral particulate matter emissions could adversely impact environmental quality in mining regions, transport regions, and even on a global scale. Mineral loading is an important process contributing to mineral particulate matter emissions, especially under weak wind conditions. Mathematical models are effective ways to evaluate particulate matter emissions during the mineral loading process. The currently used empirical models based on the form of a power function do not predict particulate matter emissions accurately under weak wind conditions. At low particulate matter emissions, the models overestimated, and at high particulate matter emissions, the models underestimated emission factors. We conducted wind tunnel experiments to evaluate the particulate matter emission factors for the mineral loading process. A new approach based on the mathematical form of a logistical function was developed and tested. It provided a realistic depiction of the particulate matter emissions during the mineral loading process, accounting for fractions of fine mineral particles, dropping height, and wind velocity. Copyright © 2013 Elsevier B.V. All rights reserved.
Evaluation of 14 global GIA forward models using a novel GPS dataset and GRACE
NASA Astrophysics Data System (ADS)
Bamber, J. L.; Schumacher, M.; Sha, Z.; Rougier, J.; King, M. A.; Khan, S. A.; Shum, C. K.; Luthcke, S. B.
2017-12-01
Observed mass movement from GRACE and vertical land motion from a global network of permanent GPS stations are used in a data driven approach to estimate GIA signals without introducing any assumptions about Earth structure nor ice loading history. Satellite data and in-situ observations are combined using a multivariate spatiotemporal model within a Bayesian Hierarchical Modelling (BHM) framework. In this study, the GPS data set of the Nevada Geodetic Laboratory (NGL) is used as the starting point for providing an observational estimate of global GIA uplift rates. A novel fully automatic post-processing strategy is developed to correct for non-GIA artifacts, including: (i) outlier detection (e.g. due to icing of Choke Ring Antennas or the antenna being buried in snow); (ii) automatic removal of reported and unreported jumps due to geophysical and hardware issues (a refinement of the jump database provided by NGL); and (iii) filtering for GPS stations that observe primarily the GIA signal rather than unwanted local effects (e.g., unmodelled loading effects from land hydrology, atmosphere, or tides). In order to accurately account for the elastic response of the Earth's crust over Antarctica and Greenland, uplift rates in these regions were corrected for the contemporary ice mass loading impact on elastic deformation using high-resolution ice mass balance time series. The novel global GPS data set shows a clean GIA signal at all post-processed stations and is therefore suitable to investigate the behavior of global GIA forward models. In addition, NASA's GSFC GRACE global mascon solutions are employed. The equal area 1x1 degree gridded mascons are spatially aggregated for larger regions to account for their spatial error correlations. Both the GPS and GRACE datasets are combined with prior information about spatial wavelengths of GIA signals obtained from the ICE-6G model within the BHM framework to solve for GIA. The results are compared with 14 global GIA forward model solutions to identify statistically significant deviations between the forward and inverse solutions, which may be due to either uncertain mantle rheology and/or ice loading history/magnitude.
NASA Astrophysics Data System (ADS)
Ravikumar, Nakul; Rogalski, Melissa M.; Benza, Donny; Lake, Joshua; Urban, Matthew; Pelham, Hunter; Anker, Jeffrey N.; DesJardins, John D.
2017-03-01
An orthopaedic screw was designed with an optical tension-indicator to non-invasively quantify screw tension and monitor the load sharing between the bone and the implant. The screw both applies load to the bone, and measures this load by reporting the strain on the screw. The screw contains a colorimetric optical encoder that converts axial strain into colorimetric changes visible through the head of the screw, or luminescent spectral changes that are detected through tissue. Screws were tested under cyclic mechanical loading to mimic in-vivo conditions to verify the sensitivity, repeatability, and reproducibility of the sensor. In the absence to tissue, color was measured using a digital camera as a function of axial load on a stainless steel cannulated (hollow) orthopedic screw, modified by adding a passive colorimetric strain gauge through the central hole. The sensor was able to quantify clinically-relevant bone healing strains. The sensor exhibited good repeatability and reproducibility but also displayed hysteresis due to the internal mechanics of the screw. The strain indicator was also modified for measurement through tissue by replacing the reflective colorimetric sensor with a low-background X-ray excited optical luminescence signal. Luminescent spectra were acquired through 6 mm of chicken breast tissue. Overall, this research shows feasibility for a unique device which quantifies the strain on an orthopedic screw. Future research will involve reducing hysteresis by changing the mechanism of strain transduction in the screw, miniaturizing the luminescent strain gauge, monitoring bending as well as tension, using alternative luminescent spectral rulers based upon near infrared fluorescence or upconversion luminescence, and application to monitoring changes in pretension and load sharing during bone healing.
Confucius Institutes: Distributed Leadership and Knowledge Sharing in a Worldwide Network
ERIC Educational Resources Information Center
Li, Hsi Chang; Mirmirani, Sam; Ilacqua, Joseph A.
2009-01-01
Purpose: The purpose of this paper is to focus on Confucius Institutes and assess the applicability of theories of leadership and knowledge sharing to multinational organizations and worldwide networks. Growth of multinational trade and decrease in international tension have facilitated the globalization of both profit-seeking and non-profit…
78 FR 11909 - Emerging Global Advisors, LLC, et al.; Notice of Application
Federal Register 2010, 2011, 2012, 2013, 2014
2013-02-20
... SECURITIES AND EXCHANGE COMMISSION [Investment Company Act Release No. 30382; 812-14117] Emerging... Investment Company Act of 1940 (``Act'') for an exemption from sections 2(a)(32), 5(a)(1), 22(d) and 22(e) of... management investment companies to issue shares (``Shares'') redeemable in large aggregations only...
ERIC Educational Resources Information Center
Yarfoh, Charles H.
2011-01-01
Francis W. Parker School invited Charles H. Yarfoh, the founder of its sister school, to Chicago to share his vision and what it has meant to the students of his school, Tuskegee International, to be part of the global connection between the two schools. In a speech he delivered to the faculty, staff, and students, Yarfoh shares what education…
Karthikayan, S; Sankaranarayanan, G; Karthikeyan, R
2015-11-01
Present energy strategies focus on environmental issues, especially environmental pollution prevention and control by eco-friendly green technologies. This includes, increase in the energy supplies, encouraging cleaner and more efficient energy management, addressing air pollution, greenhouse effect, global warming, and climate change. Biofuels provide the panorama of new fiscal opportunities for people in rural area for meeting their need and also the demand of the local market. Biofuels concern protection of the environment and job creation. Renewable energy sources are self-reliance resources, have the potential in energy management with less emissions of air pollutants. Biofuels are expected to reduce dependability on imported crude oil with connected economic susceptibility, reduce greenhouse gases, other pollutants and invigorate the economy by increasing demand and prices for agricultural products. The use of neat paradise tree oil and induction of eco-friendly material Hydrogen through inlet manifold in a constant pressure heat addition cycle engine (diesel engine) with optimized engine operating parameters such as injection timing, injection pressure and compression ratio. The results shows the heat utilization efficiency for neat vegetable oil is 29% and neat oil with 15% Hydrogen as 33%. The exhaust gas temperature (EGT) for 15% of H2 share as 450°C at full load and the heat release of 80J/deg. crank angle for 15% Hydrogen energy share. Copyright © 2015 Elsevier Inc. All rights reserved.
Sun, Zhiqian; Song, Gian; Sisneros, Thomas A.; Clausen, Bjørn; Pu, Chao; Li, Lin; Gao, Yanfei; Liaw, Peter K.
2016-01-01
An understanding of load sharing among constituent phases aids in designing mechanical properties of multiphase materials. Here we investigate load partitioning between the body-centered-cubic iron matrix and NiAl-type precipitates in a ferritic alloy during uniaxial tensile tests at 364 and 506 °C on multiple length scales by in situ neutron diffraction and crystal plasticity finite element modeling. Our findings show that the macroscopic load-transfer efficiency is not as high as that predicted by the Eshelby model; moreover, it depends on the matrix strain-hardening behavior. We explain the grain-level anisotropic load-partitioning behavior by considering the plastic anisotropy of the matrix and elastic anisotropy of precipitates. We further demonstrate that the partitioned load on NiAl-type precipitates relaxes at 506 °C, most likely through thermally-activated dislocation rearrangement on the microscopic scale. The study contributes to further understanding of load-partitioning characteristics in multiphase materials. PMID:26979660
Sun, Zhiqian; Song, Gian; Sisneros, Thomas A.; ...
2016-03-16
An understanding of load sharing among constituent phases aids in designing mechanical properties of multiphase materials. Here we investigate load partitioning between the body-centered-cubic iron matrix and NiAl-type precipitates in a ferritic alloy during uniaxial tensile tests at 364 and 506 C on multiple length scales by in situ neutron diffraction and crystal plasticity finite element modeling. Our findings show that the macroscopic load-transfer efficiency is not as high as that predicted by the Eshelby model; moreover, it depends on the matrix strain-hardening behavior. We explain the grain-level anisotropic load-partitioning behavior by considering the plastic anisotropy of the matrix andmore » elastic anisotropy of precipitates. We further demonstrate that the partitioned load on NiAl-type precipitates relaxes at 506 C, most likely through thermally-activated dislocation rearrangement on the microscopic scale. Furthermore, the study contributes to further understanding of load-partitioning characteristics in multiphase materials.« less
The Tension Between Data Sharing and the Protection of Privacy in Genomics Research
Kaye, Jane
2014-01-01
Next-generation sequencing and global data sharing challenge many of the governance mechanisms currently in place to protect the privacy of research participants. These challenges will make it more difficult to guarantee anonymity for participants, provide information to satisfy the requirements of informed consent, and ensure complete withdrawal from research when requested. To move forward, we need to improve the current governance systems for research so that they are responsive to individual privacy concerns but can also be effective at a global level. We need to develop a system of e-governance that can complement existing governance systems but that places greater reliance on the use of technology to ensure compliance with ethical and legal requirements. These new governance structures must be able to address the concerns of research participants while at the same time ensuring effective data sharing that promotes public trust in genomics research. PMID:22404490
The tension between data sharing and the protection of privacy in genomics research.
Kaye, Jane
2012-01-01
Next-generation sequencing and global data sharing challenge many of the governance mechanisms currently in place to protect the privacy of research participants. These challenges will make it more difficult to guarantee anonymity for participants, provide information to satisfy the requirements of informed consent, and ensure complete withdrawal from research when requested. To move forward, we need to improve the current governance systems for research so that they are responsive to individual privacy concerns but can also be effective at a global level. We need to develop a system of e-governance that can complement existing governance systems but that places greater reliance on the use of technology to ensure compliance with ethical and legal requirements. These new governance structures must be able to address the concerns of research participants while at the same time ensuring effective data sharing that promotes public trust in genomics research.
NASA Technical Reports Server (NTRS)
Soltis, Steven R.; Ruwart, Thomas M.; OKeefe, Matthew T.
1996-01-01
The global file system (GFS) is a prototype design for a distributed file system in which cluster nodes physically share storage devices connected via a network-like fiber channel. Networks and network-attached storage devices have advanced to a level of performance and extensibility so that the previous disadvantages of shared disk architectures are no longer valid. This shared storage architecture attempts to exploit the sophistication of storage device technologies whereas a server architecture diminishes a device's role to that of a simple component. GFS distributes the file system responsibilities across processing nodes, storage across the devices, and file system resources across the entire storage pool. GFS caches data on the storage devices instead of the main memories of the machines. Consistency is established by using a locking mechanism maintained by the storage devices to facilitate atomic read-modify-write operations. The locking mechanism is being prototyped in the Silicon Graphics IRIX operating system and is accessed using standard Unix commands and modules.
GLobal Integrated Design Environment (GLIDE): A Concurrent Engineering Application
NASA Technical Reports Server (NTRS)
McGuire, Melissa L.; Kunkel, Matthew R.; Smith, David A.
2010-01-01
The GLobal Integrated Design Environment (GLIDE) is a client-server software application purpose-built to mitigate issues associated with real time data sharing in concurrent engineering environments and to facilitate discipline-to-discipline interaction between multiple engineers and researchers. GLIDE is implemented in multiple programming languages utilizing standardized web protocols to enable secure parameter data sharing between engineers and researchers across the Internet in closed and/or widely distributed working environments. A well defined, HyperText Transfer Protocol (HTTP) based Application Programming Interface (API) to the GLIDE client/server environment enables users to interact with GLIDE, and each other, within common and familiar tools. One such common tool, Microsoft Excel (Microsoft Corporation), paired with its add-in API for GLIDE, is discussed in this paper. The top-level examples given demonstrate how this interface improves the efficiency of the design process of a concurrent engineering study while reducing potential errors associated with manually sharing information between study participants.
Sato, Yousuke; Goto, Daisuke; Michibata, Takuro; Suzuki, Kentaroh; Takemura, Toshihiko; Tomita, Hirofumi; Nakajima, Teruyuki
2018-03-07
Aerosols affect climate by modifying cloud properties through their role as cloud condensation nuclei or ice nuclei, called aerosol-cloud interactions. In most global climate models (GCMs), the aerosol-cloud interactions are represented by empirical parameterisations, in which the mass of cloud liquid water (LWP) is assumed to increase monotonically with increasing aerosol loading. Recent satellite observations, however, have yielded contradictory results: LWP can decrease with increasing aerosol loading. This difference implies that GCMs overestimate the aerosol effect, but the reasons for the difference are not obvious. Here, we reproduce satellite-observed LWP responses using a global simulation with explicit representations of cloud microphysics, instead of the parameterisations. Our analyses reveal that the decrease in LWP originates from the response of evaporation and condensation processes to aerosol perturbations, which are not represented in GCMs. The explicit representation of cloud microphysics in global scale modelling reduces the uncertainty of climate prediction.
Zaseck, Lauren Wood; Chen, Cong; Hu, Jingwen; Reed, Matthew P; Rupp, Jonathan
2018-03-01
Many post-mortem human subjects (PMHS) considered for use in biomechanical impact tests have pre-existing rib fractures (PERFs), usually resulting from cardiopulmonary resuscitation. These specimens are typically excluded from impact studies with the assumption that the fractures will alter the thoracic response to loading. We previously used the Global Human Body Models Consortium 50th percentile whole-body finite element model (GHBMC M50-O) to demonstrate that up to three lateral or bilateral PERFs do not meaningfully influence the response of the GHBMC thorax to lateral loading. This current study used the GHBMC M50-O to explore the influence of PERFs on thorax response in frontal and oblique loading. Up to six PERFs were simulated on the anterior or lateral rib regions, and the model was subjected to frontal or oblique cylindrical impactor, frontal seatbelt, or frontal seatbelt + airbag loading. Changes in thorax force-compression responses due to PERFs were generally minor, with the greatest alterations seen in models with six PERFs on one side of the ribcage. The observed changes, however, were small relative to mid-size male corridors for the loading conditions simulated. PERFs altered rib strain patterns, but the changes did not translate to changes in global thoracic response. Within the limits of model fidelity, the results suggest that PMHS with up to six PERFs may be appropriate for use in frontal or oblique impact testing. Copyright © 2018 Elsevier Ltd. All rights reserved.
Davey, Marie L; Skogen, Marte J; Heegaard, Einar; Halvorsen, Rune; Kauserud, Håvard; Ohlson, Mikael
2017-01-01
Human activity has more than doubled the amount of nitrogen entering the global nitrogen cycle, and the boreal forest biome is a nitrogen-limited ecosystem sensitive to nitrogen load perturbation. Although bryophyte-associated microbes contribute significantly to boreal forest ecosystem function, particularly in carbon and nitrogen cycling, little is known about their responses to anthropogenic global change. Amplicon pyrosequencing of the ITS2 region of rDNA was used to investigate how fungal communities associated with three bryophyte species responded to increased nitrogen loads in a long-term fertilization experiment in a boreal Picea abies forest in southern Norway. Overall, OTU richness, community composition and the relative abundance of specific ecological guilds were primarily influenced by host species identity and tissue type. Although not the primary factor affecting fungal communities, nitrogen addition did impact the abundance of specific guilds of fungi and the resulting overall community composition. Increased nitrogen loads decreased ectomycorrhizal abundance, with Amphinema, Cortinarius, Russula and Tylospora OTUs responding negatively to fertilization. Pathogen abundance increased with fertilization, particularly in the moss pathogen Eocronartium. Saprophytic fungi were both positively and negatively impacted by the nitrogen addition, indicating a complex community level response. The overshadowing of the effects of increased nitrogen loads by variation related to host and tissue type highlights the complexity of bryophyte-associated microbial communities and the intricate nature of their responses to anthropogenic global change. © 2016 John Wiley & Sons Ltd.
Kasper, Helmut; Lehrer, Mark; Mühlbacher, Jürgen; Müller, Barbara
2013-01-01
This qualitative field study investigated cross-site knowledge sharing in a small sample of multinational corporations in three different MNC business contexts (global, multidomestic, transnational). The results disclose heterogeneous “worlds” of MNC knowledge sharing, ultimately raising the question as to whether the whole concept of MNC knowledge sharing covers a sufficiently unitary phenomenon to be meaningful. We derive a non-exhaustive typology of MNC knowledge-sharing practices: self-organizing knowledge sharing, technocratic knowledge sharing, and best practice knowledge sharing. Despite its limitations, this typology helps to elucidate a number of issues, including the latent conflict between two disparate theories of MNC knowledge sharing, namely “sender–receiver” and “social learning” theories (Noorderhaven & Harzing, 2009). More generally, we develop the term “knowledge contextualization” to highlight the way that firm-specific organizational features pre-define which knowledge is considered to be of special relevance for intra-organizational sharing. PMID:27087759
ERIC Educational Resources Information Center
Brown, Elinor L., Ed.; Gibbons, Pamela E., Ed.
2011-01-01
This volume of Global Initiatives for Equity and Social Justice takes a resource perspective toward culture, ethnicity, and race. Its purpose is to foster global dialog about race and ethnicity, with an emphasis on sharing strategies and solutions. While one might view problems stemming from racial and ethnic differences as intractable, the book's…
Nancy Roeper; Peter Landres; Don Fisher
2006-01-01
Two days before the 8th World Wilderness Congress began in Alaska, nearly 200 government wildlands managers from 17 countries met to share ideas about common challenges and to explore ways to improve wildland stewardship globally. The goal for this Global Wilderness Seminar for Government Agencies was to lay the foundation for an operating peer network of government...
Building Global Support for Open Data Access
NASA Astrophysics Data System (ADS)
Key, E.; Samors, R. J.; Seltzer, C. E.; Orr, B. J.
2017-12-01
The Belmont Forum, a global partnership of funding organizations, international science councils, and regional consortia is committed to the advancement of international transdisciplinary research providing knowledge for understanding, mitigating and adapting to global environmental change. The Forum is also committed to ensuring appropriate, recognizable credit is awarded to the creators of that data, each and every time it is used. At its 2015 plenary meeting, the Belmont Forum agreed on and adopted an open data policy and principles. The principles are designed to widen access to data and promote its long-term preservation in global change research; help improve data management and exploitation; coordinate and integrate disparate organizational and technical elements; fill critical global e-infrastructure gaps; share best practices; and foster new data literacy. To help implement the policy and principles, the Belmont Forum has established the e-Infrastructures and Data Management (e-I&DM) Initiative which will leverage existing knowledge and resources to illuminate achievable, reproducible systems for effective, sustainable data management practices. The overall objective of the e-I&DM Initiative is to provide advice and recommendations to the Belmont Forum member and partner organizations regarding policies, programs, procedures that could be adopted to accelerate open data sharing, data reproducibility, data curation, and other aspects of long-term data management and access. This presentation will explore current Belmont Forum activities through the e-I&DM Initiative to develop policies and practices that could be adopted by funders, publishers and researchers alike that will lead to increased data sharing with more widespread data citation/attribution - giving credit where credit is due.
International Global Crop Condition Assessments in the framework of GEOGLAM
NASA Astrophysics Data System (ADS)
Becker-Reshef, I.; Justice, C. O.; Vermote, E.; Whitcraft, A. K.; Claverie, M.
2013-12-01
The Group on Earth Observations (partnership of governments and international organizations) developed the Global Agricultural Monitoring (GEOGLAM) initiative in response to the growing calls for improved agricultural information. The goal of GEOGLAM is to strengthen the international community's capacity to produce and disseminate relevant, timely and accurate forecasts of agricultural production at national, regional and global scales through the use of Earth observations. This initiative is designed to build on existing agricultural monitoring initiatives at national, regional and global levels and to enhance and strengthen them through international networking, operationally focused research, and data/method sharing. GEOGLAM was adopted by the G20 as part of the action plan on food price volatility and agriculture and is being implemented through building on the extensive GEO Agricultural Community of Practice (CoP) that was initiated in 2007 and includes key national and international agencies, organizations, and universities involved in agricultural monitoring. One of the early GEOGLAM activities is to provide harmonized global crop outlooks that offer timely qualitative consensus information on crop status and prospects. This activity is being developed in response to a request from the G-20 Agricultural Market Information System (AMIS) and is implemented within the global monitoring systems component of GEOGLAM. The goal is to develop a transparent, international, multi-source, consensus assessment of crop growing conditions, status, and agro-climatic conditions, likely to impact global production. These assessments are focused on the four primary crop types (corn, wheat, soy and rice) within the main agricultural producing regions of the world. The GEOGLAM approach is to bring together international experts from global, regional and national monitoring systems that can share and discuss information from a variety of independent complementary sources in order to reach a convergence of evidence based assessment. Information types include earth observations (EO) data and products, agro-meteorological data, crop models and field reports. To date, representatives from close to 20 different agencies have participated in these outlook assessments, which are submitted to AMIS on a monthly basis as well as shared with the international community. This talk will discuss the process, operational R&D, and progress towards developing these harmonized global crop assessments.
A global picture of biological invasion threat on islands.
Bellard, Céline; Rysman, Jean-François; Leroy, Boris; Claud, Chantal; Mace, Georgina M
2017-12-01
Biological invasions are among the main drivers of biodiversity losses. As threats from biological invasions increase, one of the most urgent tasks is to identify areas of high vulnerability. However, the lack of comprehensive information on the impacts of invasive alien species (IAS) is a problem especially on islands, where most of the recorded extinctions associated with IAS have occurred. Here we provide a global, network-oriented analysis of IAS on islands. Using network analysis, we structured 27,081 islands and 437 threatened vertebrates into 21 clusters, based on their profiles in term of invasiveness and shared vulnerabilities. These islands are mainly located in the Southern Hemisphere and many are in biodiversity hotspots. Some of the islands share similar characteristics regarding their connectivity that could be useful for understanding their response to invasive species. The major invaders found in these clusters of islands are feral cats, feral dogs, pigs and rats. Our analyses reveal those IAS that systematically act alone or in combination, and the pattern of shared IAS among threatened species, providing new information to implement effective eradication strategies. Combined with further local, contextual information this can contribute to global strategies to deal with IAS.
Online Metadata Directories: A way of preserving, sharing and discovering scientific information
NASA Technical Reports Server (NTRS)
Meaux, M.
2005-01-01
The Global Change Master Directory (GCMD) assists the scientific community in the discovery of and linkage to Earth Science data and provides data holders a means to advertise their data to the community through its portals, i.e. online customized subset metadata directories. These directories are effectively serving communities like the Joint Committee on Antarctic Data Management (JCADM), the Global Observing System Information Center (GOSIC), and the Global Ocean Ecosystems Dynamic Program (GLOBEC) by increasing the visibility of their data holding. The purpose of the Gulf of Maine Ocean Data Partnership (GoMODP) is to "promote and coordinate the sharing, linking, electronic dissemination, and use of data on the Gulf of Maine region". The participants have decided that a "coordinated effort is needed to enable users throughout the Gulf of Maine region and beyond to discover and put to use the vast and growing quantities of data in their respective databases". GoMODP members have invited the GCMD to discuss potential collaborations associated with this effort. The presentation will focus on the use of the GCMD s metadata directory as a powerful tool for data discovery and sharing. An overview of the directory and its metadata authoring tools will be given.
Health is global: proposals for a UK Government-wide strategy.
Donaldson, Liam; Banatvala, Nicholas
2007-03-10
Global health enables the harmonisation of international and domestic-health concerns-its outlook is much wider than a development or foreign-assistance perspective alone. Engaging globally in health requires the creation of relevant and effective partnerships to implement solutions for shared or common problems. To build on the UK's achievements and leadership in global health, the central government Department of Health is now leading the development of a UK Government-wide global strategy. This paper describes the rationale and process for developing the new UK Government-wide strategy for global health and highlights some of the issues that must be discussed.
Teaching Global Perspectives in a Rural Environment.
ERIC Educational Resources Information Center
Lind, Mary Ann
1980-01-01
Rural students can understand global perspectives by developing pride as food providers who share "kinship of the soil" with the developing world. Important lessons include man's dependence on the land; philosophy of environmental protection; agricultural technology; political influence over soil use; and five factors controlling crop production.…
Simpson, Annie; Jarnevich, Catherine S.; Madsen, John; Westbrooks, Randy G.; Fournier, Christine; Mehrhoff, Les; Browne, Michael; Graham, Jim; Sellers, Elizabeth A.
2009-01-01
Accurate analysis of present distributions and effective modeling of future distributions of invasive alien species (IAS) are both highly dependent on the availability and accessibility of occurrence data and natural history information about the species. Invasive alien species monitoring and detection networks (such as the Invasive Plant Atlas of New England and the Invasive Plant Atlas of the MidSouth) generate occurrence data at local and regional levels within the United States, which are shared through the US National Institute of Invasive Species Science. The Inter-American Biodiversity Information Network's Invasives Information Network (I3N), facilitates cooperation on sharing invasive species occurrence data throughout the Western Hemisphere. The I3N and other national and regional networks expose their data globally via the Global Invasive Species Information Network (GISIN). International and interdisciplinary cooperation on data sharing strengthens cooperation on strategies and responses to invasions. However, limitations to effective collaboration among invasive species networks leading to successful early detection and rapid response to invasive species include: lack of interoperability; data accessibility; funding; and technical expertise. This paper proposes various solutions to these obstacles at different geographic levels and briefly describes success stories from the invasive species information networks mentioned above. Using biological informatics to facilitate global information sharing is especially critical in invasive species science, as research has shown that one of the best indicators of the invasiveness of a species is whether it has been invasive elsewhere. Data must also be shared across disciplines because natural history information (e.g. diet, predators, habitat requirements, etc.) about a species in its native range is vital for effective prevention, detection, and rapid response to an invasion. Finally, it has been our experience that sharing information, including invasive species dispersal mechanisms and rates, impacts, and prevention and control strategies, enables resource managers and decision-makers to mount a more effective response to biological invasions.
Navy High-Strength Steel Corrosion-Fatigue Modeling Program
2006-10-01
interest. In the global analysis, the axial loading and residual stress (via the temperature profile discussed in the previous section) were applied to...developed based on observa- tions from analyses of axial load components with sinusoidally varying surface geometries. These observations indicated that...profile parameters (height and wavelength in each surface direction) and the applied axial loading . Stress Varies Sinusoidally 180° Out of Phase
Characterizing the Global Impact of P2P Overlays on the AS-Level Underlay
NASA Astrophysics Data System (ADS)
Rasti, Amir Hassan; Rejaie, Reza; Willinger, Walter
This paper examines the problem of characterizing and assessing the global impact of the load imposed by a Peer-to-Peer (P2P) overlay on the AS-level underlay. In particular, we capture Gnutella snapshots for four consecutive years, obtain the corresponding AS-level topology snapshots of the Internet and infer the AS-paths associated with each overlay connection. Assuming a simple model of overlay traffic, we analyze the observed load imposed by these Gnutella snapshots on the AS-level underlay using metrics that characterize the load seen on individual AS-paths and by the transit ASes, illustrate the churn among the top transit ASes during this 4-year period, and describe the propagation of traffic within the AS-level hierarchy.
Elastic response of (001)-oriented PWA 1480 single crystal - The influence of secondary orientation
NASA Technical Reports Server (NTRS)
Kalluri, Sreeramesh; Abdul-Azis, Ali; Mcgaw, Michael
1991-01-01
The influence of secondary orientation on the elastic response of a zone axis (001)-oriented nickel-base single-crystal superalloy, PWA 1480, was investigated under mechanical loading conditions by applying finite element techniques. Elastic stress analyses were performed with a commercially available finite element code. Secondary orientation of the single-crystal superalloy was offset with respect to the global coordinate system in increments from 0 to 90 deg and stresses developed within the single crystal were determined for each loading condition. The results indicated that the stresses were strongly influenced by the angular offset between the secondary crystal orientation and the global coordinate system. The degree of influence was found to vary with the type of loading condition (mechanical, thermal, or combined) imposed on the single-crystal superalloy.
From conceptual pluralism to practical agreement on policy: global responsibility for global health.
Ruger, Jennifer Prah; Hammonds, Rachel; Ooms, Gorik; Barry, Donna; Chapman, Audrey; Van Damme, Wim
2015-10-28
As the human cost of the global economic crisis becomes apparent the ongoing discussions surrounding the post-2015 global development framework continue at a frenzied pace. Given the scale and scope of increased globalization moving forward in a post-Millennium Development Goals era, to protect and realize health equity for all people, has never been more challenging or more important. The unprecedented nature of global interdependence underscores the importance of proposing policy solutions that advance realizing global responsibility for global health. This article argues for advancing global responsibility for global health through the creation of a Global Fund for Health. It suggests harnessing the power of the exceptional response to the combined epidemics of AIDS, TB and Malaria, embodied in the Global Fund to Fight AIDS, Tuberculosis and Malaria, to realize an expanded, reconceptualized Global Fund for Health. However this proposal creates both an analytical quandary embedded in conceptual pluralism and a practical dilemma for the scope and raison d'etre of a new Global Fund for Health. To address these issues we offer a logical framework for moving from conceptual pluralism in the theories supporting global responsibility for health to practical agreement on policy to realize this end. We examine how the innovations flowing from this exceptional response can be coupled with recent ideas and concepts, for example a global social protection floor, a Global Health Constitution or a Framework Convention for Global Health, that share the global responsibility logic that underpins a Global Fund for Health. The 2014 Lancet Commission on Global Governance for Health Report asks whether a single global health protection fund would be better for global health than the current patchwork of global and national social transfers. We concur with this suggestion and argue that there is much room for practical agreement on a Global Fund for Health that moves from the conceptual level into policies and practice that advance global health. The issues of shared responsibility and mutual accountability feature widely in the post-2015 discussions and need to be addressed in a coherent manner. Our article argues why and how a Global Fund for Health effectuates this, thus advancing global responsibility for global health.
2016-06-01
an effective system monitoring and display capability. The SOM, C-SSE, and resource managers access MUOS via a web portal called the MUOS Planning...and Provisioning Application (PlanProvApp). This web portal is their window into MUOS and is designed to provide them with a shared understanding of...including page loading errors, partially loaded web pages, incomplete reports, and inaccurate reports. For example, MUOS reported that there were
FEMCAM Analysis of SULTAN Test Results for ITER Nb3SN Cable-conduit Conductors
DOE Office of Scientific and Technical Information (OSTI.GOV)
Yuhu Zhai, Pierluigi Bruzzone, Ciro Calzolaio
2013-03-19
Performance degradation due to filament fracture of Nb3 Sn cable-in-conduit conductors (CICCs) is a critical issue in large-scale magnet designs such as ITER which is currently being constructed in the South of France. The critical current observed in most SULTAN TF CICC samples is significantly lower than expected and the voltage-current characteristic is seen to have a much broader transition from a single strand to the CICC. Moreover, most conductors exhibit the irreversible degradation due to filament fracture and strain relaxation under electromagnetic cyclic loading. With recent success in monitoring thermal strain distribution and its evolution under the electromagnetic cyclicmore » loading from in situ measurement of critical temperature, we apply FEMCAM which includes strand filament breakage and local current sharing effects to SULTAN tested CICCs to study Nb3 Sn strain sensitivity and irreversible performance degradation. FEMCAM combines the thermal bending effect during cool down and the EM bending effect due to locally accumulating Lorentz force during magnet operation. It also includes strand filament fracture and related local current sharing for the calculation of cable n value. In this paper, we model continuous performance degradation under EM cyclic loading based on strain relaxation and the transition broadening upon cyclic loading to the extreme cases seen in SULTAN test data to better quantify conductor performance degradation.« less
Optimization of composite box-beam structures including effects of subcomponent interactions
NASA Technical Reports Server (NTRS)
Ragon, Scott A.; Guerdal, Zafer; Starnes, James H., Jr.
1995-01-01
Minimum mass designs are obtained for a simple box beam structure subject to bending, torque and combined bending/torque load cases. These designs are obtained subject to point strain and linear buckling constraints. The present work differs from previous efforts in that special attention is payed to including the effects of subcomponent panel interaction in the optimal design process. Two different approaches are used to impose the buckling constraints. When the global approach is used, buckling constraints are imposed on the global structure via a linear eigenvalue analysis. This approach allows the subcomponent panels to interact in a realistic manner. The results obtained using this approach are compared to results obtained using a traditional, less expensive approach, called the local approach. When the local approach is used, in-plane loads are extracted from the global model and used to impose buckling constraints on each subcomponent panel individually. In the global cases, it is found that there can be significant interaction between skin, spar, and rib design variables. This coupling is weak or nonexistent in the local designs. It is determined that weight savings of up to 7% may be obtained by using the global approach instead of the local approach to design these structures. Several of the designs obtained using the linear buckling analysis are subjected to a geometrically nonlinear analysis. For the designs which were subjected to bending loads, the innermost rib panel begins to collapse at less than half the intended design load and in a mode different from that predicted by linear analysis. The discrepancy between the predicted linear and nonlinear responses is attributed to the effects of the nonlinear rib crushing load, and the parameter which controls this rib collapse failure mode is shown to be the rib thickness. The rib collapse failure mode may be avoided by increasing the rib thickness above the value obtained from the (linear analysis based) optimizer. It is concluded that it would be necessary to include geometric nonlinearities in the design optimization process if the true optimum in this case were to be found.
Covault, Jacob A.; Craddock, William H.; Romans, Brian W.; Fildani, Andrea; Gosai, Mayur
2013-01-01
Sediment generation and transport through terrestrial catchments influence soil distribution, geochemical cycling of particulate and dissolved loads, and the character of the stratigraphic record of Earth history. To assess the spatiotemporal variation in landscape evolution, we compare global compilations of stream gauge–derived () and cosmogenic radionuclide (CRN)–derived (predominantly 10Be; ) denudation of catchments (mm/yr) and sediment load of rivers (Mt/yr). Stream gauges measure suspended sediment loads of rivers during several to tens of years, whereas CRNs provide catchment-integrated denudation rates at 102–105-yr time scales. Stream gauge–derived and CRN-derived sediment loads in close proximity to one another (<500 km) exhibit broad similarity ( stream gauge samples; CRN samples). Nearly two-thirds of CRN-derived sediment loads exceed historic loads measured at the same locations (). Excessive longer-term sediment loads likely are a result of longer-term recurrence of large-magnitude sediment-transport events. Nearly 80% of sediment loads measured at approximately the same locations exhibit stream gauge loads that are within an order of magnitude of CRN loads, likely as a result of the buffering capacity of large flood plains. Catchments in which space for deposition exceeds sediment supply have greater buffering capacity. Superior locations in which to evaluate anthropogenic influences on landscape evolution might be buffered catchments, in which temporary storage of sediment in flood plains can provide stream gauge–based sediment loads and denudation rates that are applicable over longer periods than the durations of gauge measurements. The buffering capacity of catchments also has implications for interpreting the stratigraphic record; delayed sediment transfer might complicate the stratigraphic record of external forcings and catchment modification.
Fracture control method for composite tanks with load sharing liners
NASA Technical Reports Server (NTRS)
Bixler, W. D.
1975-01-01
The experimental program was based on the premise that the plastic sizing cycle, which each pressure vessel is subjected to prior to operation, acts as an effective proof test of the liner, screening out all flaws or cracks larger than a critical size. In doing so, flaw growth potential is available for cyclic operation at pressures less than the sizing pressure. Static fracture and cyclic life tests, involving laboratory type specimens and filament overwrapped tanks, were conducted on three liner materials: (1) 2219-T62 aluminum, (2) Inconel X750 STA, and (3) cryoformed 301 stainless steel. Variables included material condition, thickness, flaw size, flaw shape, temperature, sizing stress level, operating stress level and minimum-to-maximum operating stress ratio. From the empirical data base obtained, a procedure was established by which the service life of composite tanks with load sharing liners could be guaranteed with a high degree of confidence.
Tug of war of molecular motors: the effects of uneven load sharing
NASA Astrophysics Data System (ADS)
Bouzat, Sebastián; Falo, Fernando
2011-12-01
We analyze theoretically the problem of cargo transport along microtubules by motors of two species with opposite polarities. We consider two different one-dimensional models previously developed in the literature: a quite widespread model which assumes equal force sharing, here referred to as the mean field model (MFM), and a stochastic model (SM) which considers individual motor-cargo links. We find that in generic situations, the MFM predicts larger cargo mean velocity, smaller mean run time and less frequent reversions than the SM. These phenomena are found to be the consequences of the load sharing assumptions and can be interpreted in terms of the probabilities of the different motility states. We also explore the influence of the viscosity in both models and the role of the stiffness of the motor-cargo links within the SM. Our results show that the mean cargo velocity is independent of the stiffness, while the mean run time decreases with such a parameter. We explore the case of symmetric forward and backward motors considering kinesin-1 parameters, and the problem of transport by kinesin-1 and cytoplasmic dyneins considering two different sets of parameters previously proposed for dyneins.
Method for prefetching non-contiguous data structures
Blumrich, Matthias A [Ridgefield, CT; Chen, Dong [Croton On Hudson, NY; Coteus, Paul W [Yorktown Heights, NY; Gara, Alan G [Mount Kisco, NY; Giampapa, Mark E [Irvington, NY; Heidelberger, Philip [Cortlandt Manor, NY; Hoenicke, Dirk [Ossining, NY; Ohmacht, Martin [Brewster, NY; Steinmacher-Burow, Burkhard D [Mount Kisco, NY; Takken, Todd E [Mount Kisco, NY; Vranas, Pavlos M [Bedford Hills, NY
2009-05-05
A low latency memory system access is provided in association with a weakly-ordered multiprocessor system. Each processor in the multiprocessor shares resources, and each shared resource has an associated lock within a locking device that provides support for synchronization between the multiple processors in the multiprocessor and the orderly sharing of the resources. A processor only has permission to access a resource when it owns the lock associated with that resource, and an attempt by a processor to own a lock requires only a single load operation, rather than a traditional atomic load followed by store, such that the processor only performs a read operation and the hardware locking device performs a subsequent write operation rather than the processor. A simple perfecting for non-contiguous data structures is also disclosed. A memory line is redefined so that in addition to the normal physical memory data, every line includes a pointer that is large enough to point to any other line in the memory, wherein the pointers to determine which memory line to prefect rather than some other predictive algorithm. This enables hardware to effectively prefect memory access patterns that are non-contiguous, but repetitive.
Low latency memory access and synchronization
DOE Office of Scientific and Technical Information (OSTI.GOV)
Blumrich, Matthias A.; Chen, Dong; Coteus, Paul W.
A low latency memory system access is provided in association with a weakly-ordered multiprocessor system. Each processor in the multiprocessor shares resources, and each shared resource has an associated lock within a locking device that provides support for synchronization between the multiple processors in the multiprocessor and the orderly sharing of the resources. A processor only has permission to access a resource when it owns the lock associated with that resource, and an attempt by a processor to own a lock requires only a single load operation, rather than a traditional atomic load followed by store, such that the processormore » only performs a read operation and the hardware locking device performs a subsequent write operation rather than the processor. A simple prefetching for non-contiguous data structures is also disclosed. A memory line is redefined so that in addition to the normal physical memory data, every line includes a pointer that is large enough to point to any other line in the memory, wherein the pointers to determine which memory line to prefetch rather than some other predictive algorithm. This enables hardware to effectively prefetch memory access patterns that are non-contiguous, but repetitive.« less
Low latency memory access and synchronization
DOE Office of Scientific and Technical Information (OSTI.GOV)
Blumrich, Matthias A.; Chen, Dong; Coteus, Paul W.
A low latency memory system access is provided in association with a weakly-ordered multiprocessor system. Bach processor in the multiprocessor shares resources, and each shared resource has an associated lock within a locking device that provides support for synchronization between the multiple processors in the multiprocessor and the orderly sharing of the resources. A processor only has permission to access a resource when it owns the lock associated with that resource, and an attempt by a processor to own a lock requires only a single load operation, rather than a traditional atomic load followed by store, such that the processormore » only performs a read operation and the hardware locking device performs a subsequent write operation rather than the processor. A simple prefetching for non-contiguous data structures is also disclosed. A memory line is redefined so that in addition to the normal physical memory data, every line includes a pointer that is large enough to point to any other line in the memory, wherein the pointers to determine which memory line to prefetch rather than some other predictive algorithm. This enables hardware to effectively prefetch memory access patterns that are non-contiguous, but repetitive.« less
On the impact of reducing global geophysical fluid model deformations in SLR data processing
NASA Astrophysics Data System (ADS)
Weigelt, Matthias; Thaller, Daniela
2016-04-01
Mass redistributions in the atmosphere, oceans and the continental hydrology cause elastic loading deformations of the Earth's crust and thus systematically influence Earth-bound observation systems such as VLBI, GNSS or SLR. Causing non-linear station variations, these loading deformations have a direct impact on the estimated station coordinates and an indirect impact on other parameters of global space-geodetic solutions, e.g. Earth orientation parameters, geocenter coordinates, satellite orbits or troposphere parameters. Generally, the impact can be mitigated by co-parameterisation or by reducing deformations derived from global geophysical fluid models. Here, we focus on the latter approach. A number of data sets modelling the (non-tidal) loading deformations are generated by various groups. They show regionally and locally significant differences and consequently the impact on the space-geodetic solutions heavily depends on the available network geometry. We present and discuss the differences between these models and choose SLR as the speace-geodetic technique of interest in order to discuss the impact of atmospheric, oceanic and hydrological loading on the parameters of space-geodetic solutions when correcting for the global geophysical fluid models at the observation level. Special emphasis is given to a consistent usage of models for geometric and gravimetric corrections during the data processing. We quantify the impact of the different deformation models on the station coordinates and discuss the improvement in the Earth orientation parameters and the geocenter motion. We also show that a significant reduction in the RMS of the station coordinates can be achieved depending on the model of choice.
Process-based modelling of phosphorus transformations and retention in global rivers
NASA Astrophysics Data System (ADS)
Vilmin, Lauriane; Mogollon, Jose; Beusen, Arthur; Bouwman, Lex
2016-04-01
Phosphorus (P) plays a major role in the biogeochemical functioning of aquatic systems. It typically acts as the limiting nutrient for primary productivity in freshwater bodies, and thus the increase in anthropogenic P loads during the XXth century has fuelled the eutrophication of these systems. Total P retention in global rivers has also escalated over this timeframe as demonstrated via a global model that implements the spiralling method at a spatial resolution of 0.5° (IMAGE-GNM, Beusen et al., 2015). Here, we refine this coupled hydrological - nutrient model by including mechanistic biogeochemical interactions that govern the P cycle. Special attention is paid to the representation of particle processes (i.e. particle loading, sedimentation and erosion), which play a major role in P transport and accumulation in aquatic systems. Our preliminary results are compared to measurements of suspended sediments, total P and orthophosphates in selected river basins. Initial model results show that P concentrations are particularly sensitive to particulate load distribution in the river network within a grid cell. This novel modelling approach will eventually allow a better assessment of the amounts of different forms of P (organic P, soluble reactive P, and particulate inorganic P), of P transformation rates and retention in inland waters. References Beusen, A.H.W., Van Beek, L.P.H., Bouwman, A.F., Mogollón, J.M., Middelburg, J.J. 2015. Coupling global models for hydrology and nutrient loading to simulate nitrogen and phosphorus retention in surface water - description of the IMAGE-GNM and analysis of performance. Geosci. Model Dev. 8, 4045-4067
Yokoyama, Yoshie; Jelenkovic, Aline; Hur, Yoon-Mi; Sund, Reijo; Fagnani, Corrado; Stazi, Maria A; Brescianini, Sonia; Ji, Fuling; Ning, Feng; Pang, Zengchang; Knafo-Noam, Ariel; Mankuta, David; Abramson, Lior; Rebato, Esther; Hopper, John L; Cutler, Tessa L; Saudino, Kimberly J; Nelson, Tracy L; Whitfield, Keith E; Corley, Robin P; Huibregtse, Brooke M; Derom, Catherine A; Vlietinck, Robert F; Loos, Ruth J F; Llewellyn, Clare H; Fisher, Abigail; Bjerregaard-Andersen, Morten; Beck-Nielsen, Henning; Sodemann, Morten; Krueger, Robert F; McGue, Matt; Pahlen, Shandell; Bartels, Meike; van Beijsterveldt, Catharina E M; Willemsen, Gonneke; Harris, Jennifer R; Brandt, Ingunn; Nilsen, Thomas S; Craig, Jeffrey M; Saffery, Richard; Dubois, Lise; Boivin, Michel; Brendgen, Mara; Dionne, Ginette; Vitaro, Frank; Haworth, Claire M A; Plomin, Robert; Bayasgalan, Gombojav; Narandalai, Danshiitsoodol; Rasmussen, Finn; Tynelius, Per; Tarnoki, Adam D; Tarnoki, David L; Ooki, Syuichi; Rose, Richard J; Pietiläinen, Kirsi H; Sørensen, Thorkild I A; Boomsma, Dorret I; Kaprio, Jaakko; Silventoinen, Karri
2018-05-19
The genetic architecture of birth size may differ geographically and over time. We examined differences in the genetic and environmental contributions to birthweight, length and ponderal index (PI) across geographical-cultural regions (Europe, North America and Australia, and East Asia) and across birth cohorts, and how gestational age modifies these effects. Data from 26 twin cohorts in 16 countries including 57 613 monozygotic and dizygotic twin pairs were pooled. Genetic and environmental variations of birth size were estimated using genetic structural equation modelling. The variance of birthweight and length was predominantly explained by shared environmental factors, whereas the variance of PI was explained both by shared and unique environmental factors. Genetic variance contributing to birth size was small. Adjusting for gestational age decreased the proportions of shared environmental variance and increased the propositions of unique environmental variance. Genetic variance was similar in the geographical-cultural regions, but shared environmental variance was smaller in East Asia than in Europe and North America and Australia. The total variance and shared environmental variance of birth length and PI were greater from the birth cohort 1990-99 onwards compared with the birth cohorts from 1970-79 to 1980-89. The contribution of genetic factors to birth size is smaller than that of shared environmental factors, which is partly explained by gestational age. Shared environmental variances of birth length and PI were greater in the latest birth cohorts and differed also across geographical-cultural regions. Shared environmental factors are important when explaining differences in the variation of birth size globally and over time.
NASA Technical Reports Server (NTRS)
Childs, D. W.
1984-01-01
Rotational stability of turbopump components in the space shuttle main engine was studied via analysis of component and structural dynamic models. Subsynchronous vibration caused unacceptable migration of the rotor/housing unit with unequal load sharing of the synchronous bearings that resulted in the failure of the High Pressure Oxygen Turbopump. Linear analysis shows that a shrouded inducer eliminates the second critical speed and the stability problem, a stiffened rotor improves the rotordynamic characteristics of the turbopump, and installing damper boost/impeller seals reduces bearing loads. Nonlinear analysis shows that by increasing the "dead band' clearances, a marked reduction in peak bearing loads occurs.
Solar powered actuator with continuously variable auxiliary power control
NASA Technical Reports Server (NTRS)
Nola, F. J. (Inventor)
1984-01-01
A solar powered system is disclosed in which a load such as a compressor is driven by a main induction motor powered by a solar array. An auxiliary motor shares the load with the solar powered motor in proportion to the amount of sunlight available, is provided with a power factor controller for controlling voltage applied to the auxiliary motor in accordance with the loading on that motor. In one embodiment, when sufficient power is available from the solar cell, the auxiliary motor is driven as a generator by excess power from the main motor so as to return electrical energy to the power company utility lines.
The social and ecological transitions of shrinking cities -- San Juan, Puerto Rico as a case study
Urban populations continue to increase globally and cities have become the dominant human habitat. However, the growth of cities is not universal. One in six cities globally is losing population. Shrinking cities share common attributes such as decreased household income, reduced...
Beginning the Assessment Institute and Building Global Networks
ERIC Educational Resources Information Center
Culver, Steven M.; Kniola, David
2013-01-01
The globalization of science and scholarship and the worldwide massification of post-secondary/tertiary education is creating an atmosphere that is at once competitive between and collaborative among colleges and universities. Because of the importance of these institutions to the shared economic futures of individuals and countries, there are…
78 FR 3477 - International Mail Contracts
Federal Register 2010, 2011, 2012, 2013, 2014
2013-01-16
... they share similar cost and market characteristics. Id. at 5. It notes that the pricing formula and...-filed Postal Service request concerning an additional Global Plus 2C contract. This document invites... announcing that it is entering into an additional Global Plus 2C contract (Agreement).\\1\\ The Postal Service...
Fostering Global Citizenship Education for Teachers through Online Research
ERIC Educational Resources Information Center
Harshman, Jason R.; Augustine, Tami A.
2013-01-01
This article is based on a study involving 126 International Baccalaureate (IB) teachers in more than 30 countries who, through the use of asynchronous online discussion forums, shared how they teach and simultaneously reflected upon how they conceptualize global citizenship. Data analysis revealed that participants developed new understandings…
ERIC Educational Resources Information Center
Charles, Harvey; Harris, Michelle; Carlson, Bronwyn
2016-01-01
Indigenous Studies is a rapidly growing field of enquiry both nationally and internationally. The internationalisation of the discipline is dependent on its interdiciplinarity and on the collaborative efforts of interdisciplinary scholars. Colonised Indigenous people globally share similar experiences despite differences in histories and contexts.…
Strategic Bridge Towards Community Building: The Military’s Role
2008-03-24
matched easily by much of government—to address in its own way some significant domestic and global issues not normally associated with the private...wide-range of global issues and shared concerns, but there are other examples of strategic bridge organizations in recent years as well. The U.S
Export of Plastic Debris by Rivers into the Sea.
Schmidt, Christian; Krauth, Tobias; Wagner, Stephan
2017-11-07
A substantial fraction of marine plastic debris originates from land-based sources and rivers potentially act as a major transport pathway for all sizes of plastic debris. We analyzed a global compilation of data on plastic debris in the water column across a wide range of river sizes. Plastic debris loads, both microplastic (particles <5 mm) and macroplastic (particles >5 mm) are positively related to the mismanaged plastic waste (MMPW) generated in the river catchments. This relationship is nonlinear where large rivers with population-rich catchments delivering a disproportionately higher fraction of MMPW into the sea. The 10 top-ranked rivers transport 88-95% of the global load into the sea. Using MMPW as a predictor we calculate the global plastic debris inputs form rivers into the sea to range between 0.41 and 4 × 10 6 t/y. Due to the limited amount of data high uncertainties were expected and ultimately confirmed. The empirical analysis to quantify plastic loads in rivers can be extended easily by additional potential predictors other than MMPW, for example, hydrological conditions.
Redwood-Campbell, Lynda; Pakes, Barry; Rouleau, Katherine; MacDonald, Colla J; Arya, Neil; Purkey, Eva; Schultz, Karen; Dhatt, Reena; Wilson, Briana; Hadi, Abdullahel; Pottie, Kevin
2011-07-22
Recognizing the growing demand from medical students and residents for more comprehensive global health training, and the paucity of explicit curricula on such issues, global health and curriculum experts from the six Ontario Family Medicine Residency Programs worked together to design a framework for global health curricula in family medicine training programs. A working group comprised of global health educators from Ontario's six medical schools conducted a scoping review of global health curricula, competencies, and pedagogical approaches. The working group then hosted a full day meeting, inviting experts in education, clinical care, family medicine and public health, and developed a consensus process and draft framework to design global health curricula. Through a series of weekly teleconferences over the next six months, the framework was revised and used to guide the identification of enabling global health competencies (behaviours, skills and attitudes) for Canadian Family Medicine training. The main outcome was an evidence-informed interactive framework http://globalhealth.ennovativesolution.com/ to provide a shared foundation to guide the design, delivery and evaluation of global health education programs for Ontario's family medicine residency programs. The curriculum framework blended a definition and mission for global health training, core values and principles, global health competencies aligning with the Canadian Medical Education Directives for Specialists (CanMEDS) competencies, and key learning approaches. The framework guided the development of subsequent enabling competencies. The shared curriculum framework can support the design, delivery and evaluation of global health curriculum in Canada and around the world, lay the foundation for research and development, provide consistency across programmes, and support the creation of learning and evaluation tools to align with the framework. The process used to develop this framework can be applied to other aspects of residency curriculum development.
2011-01-01
Background Recognizing the growing demand from medical students and residents for more comprehensive global health training, and the paucity of explicit curricula on such issues, global health and curriculum experts from the six Ontario Family Medicine Residency Programs worked together to design a framework for global health curricula in family medicine training programs. Methods A working group comprised of global health educators from Ontario's six medical schools conducted a scoping review of global health curricula, competencies, and pedagogical approaches. The working group then hosted a full day meeting, inviting experts in education, clinical care, family medicine and public health, and developed a consensus process and draft framework to design global health curricula. Through a series of weekly teleconferences over the next six months, the framework was revised and used to guide the identification of enabling global health competencies (behaviours, skills and attitudes) for Canadian Family Medicine training. Results The main outcome was an evidence-informed interactive framework http://globalhealth.ennovativesolution.com/ to provide a shared foundation to guide the design, delivery and evaluation of global health education programs for Ontario's family medicine residency programs. The curriculum framework blended a definition and mission for global health training, core values and principles, global health competencies aligning with the Canadian Medical Education Directives for Specialists (CanMEDS) competencies, and key learning approaches. The framework guided the development of subsequent enabling competencies. Conclusions The shared curriculum framework can support the design, delivery and evaluation of global health curriculum in Canada and around the world, lay the foundation for research and development, provide consistency across programmes, and support the creation of learning and evaluation tools to align with the framework. The process used to develop this framework can be applied to other aspects of residency curriculum development. PMID:21781319
Federal Register 2010, 2011, 2012, 2013, 2014
2012-05-22
... procedures designed to prevent the use and dissemination of material non-public information regarding such... Intermarket Surveillance Group (``ISG''), which includes all U.S. national securities exchanges and certain... throughout the world. Global shares are the actual (ordinary) shares of a non-U.S. company which trade both...
Distribution and Causes of Global Forest Fragmentation
Timothy G. Wade; Kurt H. Riitters; James D. Wickham; K. Bruce Jones
2003-01-01
Abstract Because human land uses tend to expand over time, forests that share a high proportion of their borders with anthropogenic uses are at higher risk of further degradation than forests that share a high proportion of their borders with non-forest, natural land cover (e.g., wetland). Using 1-km advanced very high resolution radiometer (AVHRR)...
Burkhart, Stephen S; Denard, Patrick J; Konicek, John; Hanypsiak, Bryan T
2014-02-01
Poor-quality tendon is one of the most difficult problems the surgeon must overcome in achieving secure fixation during rotator cuff repair. A load-sharing rip-stop construct (LSRS) has recently been proposed as a method for improving fixation strength, but the biomechanical properties of this construct have not yet been examined. To compare the strength of the LSRS construct to that of single-row fixation for rotator cuff repair. Controlled laboratory study. Rotator cuff tears were created in 6 cadaveric matched-pair specimens and repaired with a single row or an LSRS. In the LSRS repair, a 2-mm suture tape was placed as an inverted mattress stitch in the rotator cuff, and sutures from 2 anchors were placed as simple stitches that passed medial to the suture tape. The suture tape limbs were secured with knotless anchors laterally before sutures were tied from the medial anchors. Displacement was observed with video tracking after cyclic loading, and specimens were loaded to failure. The mean load to failure was 371 ± 102 N in single-row repairs compared with 616 ± 185 N in LSRS repairs (P = .031). There was no difference in displacement with cyclic loading between the groups (3.3 ± 0.8 mm vs. 3.5 ± 1.1 mm; P = .561). In the single-row group, 4 of 6 failures occurred at the suture-tendon interface. In the LSRS group, only 1 failure occurred at the suture-tendon interface. The ultimate failure load of the LSRS construct for rotator cuff repair was 1.7 times that of a single-row construct in a cadaveric model. The LSRS rotator cuff repair construct may be useful in the repair of difficult tears such as massive tears, medial tears, and tears with tendon loss.
Dynamics of a split torque helicopter transmission
NASA Astrophysics Data System (ADS)
Krantz, Timothy L.
1994-06-01
Split torque designs, proposed as alternatives to traditional planetary designs for helicopter main rotor transmissions, can save weight and be more reliable than traditional designs. This report presents the results of an analytical study of the system dynamics and performance of a split torque gearbox that uses a balance beam mechanism for load sharing. The Lagrange method was applied to develop a system of equations of motion. The mathematical model includes time-varying gear mesh stiffness, friction, and manufacturing errors. Cornell's method for calculating the stiffness of spur gear teeth was extended and applied to helical gears. The phenomenon of sidebands spaced at shaft frequencies about gear mesh fundamental frequencies was simulated by modeling total composite gear errors as sinusoid functions. Although the gearbox has symmetric geometry, the loads and motions of the two power paths differ. Friction must be considered to properly evaluate the balance beam mechanism. For the design studied, the balance beam is not an effective device for load sharing unless the coefficient of friction is less than 0.003. The complete system stiffness as represented by the stiffness matrix used in this analysis must be considered to precisely determine the optimal tooth indexing position.
Dynamics of a split torque helicopter transmission. M.S. Thesis - Cleveland State Univ.
NASA Technical Reports Server (NTRS)
Krantz, Timothy L.
1994-01-01
Split torque designs, proposed as alternatives to traditional planetary designs for helicopter main rotor transmissions, can save weight and be more reliable than traditional designs. This report presents the results of an analytical study of the system dynamics and performance of a split torque gearbox that uses a balance beam mechanism for load sharing. The Lagrange method was applied to develop a system of equations of motion. The mathematical model includes time-varying gear mesh stiffness, friction, and manufacturing errors. Cornell's method for calculating the stiffness of spur gear teeth was extended and applied to helical gears. The phenomenon of sidebands spaced at shaft frequencies about gear mesh fundamental frequencies was simulated by modeling total composite gear errors as sinusoid functions. Although the gearbox has symmetric geometry, the loads and motions of the two power paths differ. Friction must be considered to properly evaluate the balance beam mechanism. For the design studied, the balance beam is not an effective device for load sharing unless the coefficient of friction is less than 0.003. The complete system stiffness as represented by the stiffness matrix used in this analysis must be considered to precisely determine the optimal tooth indexing position.
Estimation of Local Bone Loads for the Volume of Interest.
Kim, Jung Jin; Kim, Youkyung; Jang, In Gwun
2016-07-01
Computational bone remodeling simulations have recently received significant attention with the aid of state-of-the-art high-resolution imaging modalities. They have been performed using localized finite element (FE) models rather than full FE models due to the excessive computational costs of full FE models. However, these localized bone remodeling simulations remain to be investigated in more depth. In particular, applying simplified loading conditions (e.g., uniform and unidirectional loads) to localized FE models have a severe limitation in a reliable subject-specific assessment. In order to effectively determine the physiological local bone loads for the volume of interest (VOI), this paper proposes a novel method of estimating the local loads when the global musculoskeletal loads are given. The proposed method is verified for the three VOI in a proximal femur in terms of force equilibrium, displacement field, and strain energy density (SED) distribution. The effect of the global load deviation on the local load estimation is also investigated by perturbing a hip joint contact force (HCF) in the femoral head. Deviation in force magnitude exhibits the greatest absolute changes in a SED distribution due to its own greatest deviation, whereas angular deviation perpendicular to a HCF provides the greatest relative change. With further in vivo force measurements and high-resolution clinical imaging modalities, the proposed method will contribute to the development of reliable patient-specific localized FE models, which can provide enhanced computational efficiency for iterative computing processes such as bone remodeling simulations.
International Collaborative Research Partnerships: Blending Science with Management and Diplomacy.
Lau, Chuen-Yen; Wang, Crystal; Orsega, Susan; Tramont, Edmund C; Koita, Ousmane; Polis, Michael A; Siddiqui, Sophia
2014-12-01
As globalization progressively connects and impacts the health of people across the world, collaborative research partnerships provide mutual advantages by sharing knowledge and resources to address locally and globally relevant scientific and public health questions. Partnerships undertaken for scientific research are similar to business collaborations in that they require attention to partner systems, whether local, international, political, academic, or non-academic. Scientists, like diplomats or entrepreneurs, are representatives of their field, culture, and country and become obligatory agents in health diplomacy. This role significantly influences current and future collaborations with not only the immediate partner but with other in country partners as well. Research partnerships need continuous evaluation of the collaboration's productivity, perspectives of all partners, and desired outcomes for success to avoid engaging in "research tourism", particularly in developing regions. International engagement is a cornerstone in addressing the impact of infectious diseases globally. Global partnerships are strategically aligned with national, partner and global health priorities and may be based on specific requests for assistance from the partnering country governments. Here we share experiences from select research collaborations to highlight principles that we have found key in building long-term relationships with collaborators and in meeting the aim to address scientific questions relevant to the host country and strategic global health initiatives.
International Collaborative Research Partnerships: Blending Science with Management and Diplomacy
Lau, Chuen-Yen; Wang, Crystal; Orsega, Susan; Tramont, Edmund C; Koita, Ousmane; Polis, Michael A; Siddiqui, Sophia
2015-01-01
As globalization progressively connects and impacts the health of people across the world, collaborative research partnerships provide mutual advantages by sharing knowledge and resources to address locally and globally relevant scientific and public health questions. Partnerships undertaken for scientific research are similar to business collaborations in that they require attention to partner systems, whether local, international, political, academic, or non-academic. Scientists, like diplomats or entrepreneurs, are representatives of their field, culture, and country and become obligatory agents in health diplomacy. This role significantly influences current and future collaborations with not only the immediate partner but with other in country partners as well. Research partnerships need continuous evaluation of the collaboration’s productivity, perspectives of all partners, and desired outcomes for success to avoid engaging in “research tourism”, particularly in developing regions. International engagement is a cornerstone in addressing the impact of infectious diseases globally. Global partnerships are strategically aligned with national, partner and global health priorities and may be based on specific requests for assistance from the partnering country governments. Here we share experiences from select research collaborations to highlight principles that we have found key in building long-term relationships with collaborators and in meeting the aim to address scientific questions relevant to the host country and strategic global health initiatives. PMID:26225217
Reliable file sharing in distributed operating system using web RTC
NASA Astrophysics Data System (ADS)
Dukiya, Rajesh
2017-12-01
Since, the evolution of distributed operating system, distributed file system is come out to be important part in operating system. P2P is a reliable way in Distributed Operating System for file sharing. It was introduced in 1999, later it became a high research interest topic. Peer to Peer network is a type of network, where peers share network workload and other load related tasks. A P2P network can be a period of time connection, where a bunch of computers connected by a USB (Universal Serial Bus) port to transfer or enable disk sharing i.e. file sharing. Currently P2P requires special network that should be designed in P2P way. Nowadays, there is a big influence of browsers in our life. In this project we are going to study of file sharing mechanism in distributed operating system in web browsers, where we will try to find performance bottlenecks which our research will going to be an improvement in file sharing by performance and scalability in distributed file systems. Additionally, we will discuss the scope of Web Torrent file sharing and free-riding in peer to peer networks.
Load sharing in the growth of bundled biopolymers
Wang, Ruizhe; Carlsson, A. E.
2014-01-01
To elucidate the nature of load sharing in the growth of multiple biopolymers, we perform stochastic simulations of the growth of biopolymer bundles against obstacles under a broad range of conditions and varying assumptions. The obstacle motion due to thermal fluctuations is treated explicitly. We assume the “Perfect Brownian Ratchet” (PBR) model, in which the polymerization rate equals the free-filament rate as soon as the filament-obstacle distance exceeds the monomer size. Accurate closed-form formulas are obtained for the case of a rapidly moving obstacle. We find the following: (1) load sharing is usually sub-perfect in the sense that polymerization is slower than for a single filament carrying the same average force; (2) the sub-perfect behavior becomes significant at a total force proportional to the logarithm or the square root of the number of filaments, depending on the alignment of the filaments; (3) for the special case of slow barrier diffusion and low opposing force, an enhanced obstacle velocity for an increasing number of filaments is possible; (4) the obstacle velocity is very sensitive to the alignment of the filaments in the bundle, with a staggered alignment being an order of magnitude faster than an unstaggered one at forces of only 0.5 pN per filament for 20 filaments; (5) for large numbers of filaments, the power is maximized at a force well below 1 pN per filament; (6) for intermediate values of the obstacle diffusion coefficient, the shape of the force velocity relation is very similar to that for rapid obstacle diffusion. PMID:25489273
Load sharing in the growth of bundled biopolymers.
Wang, Ruizhe; Carlsson, A E
2014-11-01
To elucidate the nature of load sharing in the growth of multiple biopolymers, we perform stochastic simulations of the growth of biopolymer bundles against obstacles under a broad range of conditions and varying assumptions. The obstacle motion due to thermal fluctuations is treated explicitly. We assume the "Perfect Brownian Ratchet" (PBR) model, in which the polymerization rate equals the free-filament rate as soon as the filament-obstacle distance exceeds the monomer size. Accurate closed-form formulas are obtained for the case of a rapidly moving obstacle. We find the following: (1) load sharing is usually sub-perfect in the sense that polymerization is slower than for a single filament carrying the same average force; (2) the sub-perfect behavior becomes significant at a total force proportional to the logarithm or the square root of the number of filaments, depending on the alignment of the filaments; (3) for the special case of slow barrier diffusion and low opposing force, an enhanced obstacle velocity for an increasing number of filaments is possible; (4) the obstacle velocity is very sensitive to the alignment of the filaments in the bundle, with a staggered alignment being an order of magnitude faster than an unstaggered one at forces of only 0.5 pN per filament for 20 filaments; (5) for large numbers of filaments, the power is maximized at a force well below 1 pN per filament; (6) for intermediate values of the obstacle diffusion coefficient, the shape of the force velocity relation is very similar to that for rapid obstacle diffusion.
NASA Technical Reports Server (NTRS)
Ku, Jentung; Ottenstein, Laura
2011-01-01
This paper describes thermal vacuum testing of a proto-flight miniature loop heat pipe (MLHP) with two evaporators and two condensers designed for future small systems applications requiring low mass, low power and compactness. Each evaporator contains a wick with an outer diameter of 6.35 mm, and each has its own integral compensation chamber (CC). Miniaturization of the loop components reduces the volume and mass of the thermal system. Multiple evaporators provide flexibility for placement of instruments that need to be maintained at the same temperature, and facilitate heat load sharing among instruments, reducing the auxiliary heater power requirement. A flow regulator is used to regulate heat dissipations between the two condensers, allowing flexible placement of radiators on the spacecraft. A thermoelectric converter (TEC) is attached to each CC for control of the operating temperature and enhancement of start-up success. Tests performed include start-up, power cycle, sink temperature cycle, high power and low power operation, heat load sharing, and operating temperature control. The proto-flight MLHP demonstrated excellent performance in the thermal vacuum test. The loop started successfully and operated stably under various evaporator heat loads and condenser sink temperatures. The TECs were able to maintain the loop operating temperature within b1K of the desired set point temperature at all power levels and all sink temperatures. The un-powered evaporator would automatically share heat from the other powered evaporator. The flow regulator was able to regulate the heat dissipation among the radiators and prevent vapor from flowing into the liquid line.
Patterned control of human locomotion
Lacquaniti, Francesco; Ivanenko, Yuri P; Zago, Myrka
2012-01-01
There is much experimental evidence for the existence of biomechanical constraints which simplify the problem of control of multi-segment movements. In addition, it has been hypothesized that movements are controlled using a small set of basic temporal components or activation patterns, shared by several different muscles and reflecting global kinematic and kinetic goals. Here we review recent studies on human locomotion showing that muscle activity is accounted for by a combination of few basic patterns, each one timed at a different phase of the gait cycle. Similar patterns are involved in walking and running at different speeds, walking forwards or backwards, and walking under different loading conditions. The corresponding weights of distribution to different muscles may change as a function of the condition, allowing highly flexible control. Biomechanical correlates of each activation pattern have been described, leading to the hypothesis that the co-ordination of limb and body segments arises from the coupling of neural oscillators between each other and with limb mechanical oscillators. Muscle activations need only intervene during limited time epochs to force intrinsic oscillations of the system when energy is lost. PMID:22411012
Patterned control of human locomotion.
Lacquaniti, Francesco; Ivanenko, Yuri P; Zago, Myrka
2012-05-15
There is much experimental evidence for the existence of biomechanical constraints which simplify the problem of control of multi-segment movements. In addition, it has been hypothesized that movements are controlled using a small set of basic temporal components or activation patterns, shared by several different muscles and reflecting global kinematic and kinetic goals. Here we review recent studies on human locomotion showing that muscle activity is accounted for by a combination of few basic patterns, each one timed at a different phase of the gait cycle. Similar patterns are involved in walking and running at different speeds, walking forwards or backwards, and walking under different loading conditions. The corresponding weights of distribution to different muscles may change as a function of the condition, allowing highly flexible control. Biomechanical correlates of each activation pattern have been described, leading to the hypothesis that the co-ordination of limb and body segments arises from the coupling of neural oscillators between each other and with limb mechanical oscillators. Muscle activations need only intervene during limited time epochs to force intrinsic oscillations of the system when energy is lost.
Civil society organizations, the implementing partners of the Global Vaccine Action Plan.
Thacker, Naveen; Vashishtha, Vipin M; Awunyo-Akaba, Joan; Mistry, Rozina Farhad
2013-04-18
The authors illustrate by way of civil society (CS) experiences in Pakistan, India, and Ghana how the guiding principles of CS and civil society organizations (CSOs) align with those of the Global Vaccine Action Plan (GVAP); (i.e., country ownership, shared responsibility and partnership, equity, integration, sustainability, and innovation). These experiences show how CS is contributing to GVAP goals such as global polio eradication and improving vaccination coverage by removing barriers and ultimately working toward achieving Millennium Development Goal (MDG) 4-reducing child mortality. A number of CSOs working in the field of child health share some of the objectives enlisted in GVAP: that immunization becomes a national health priority; individuals, families, communities understand the importance of immunization; benefits of immunization are equitably extended to all people; and vaccination systems are part of an integrated health system. Copyright © 2012 Elsevier Ltd. All rights reserved.
Brown, Eric W.; Detter, Chris; Gerner-Smidt, Peter; Gilmour, Matthew W.; Harmsen, Dag; Hendriksen, Rene S.; Hewson, Roger; Heymann, David L.; Johansson, Karin; Ijaz, Kashef; Keim, Paul S.; Koopmans, Marion; Kroneman, Annelies; Wong, Danilo Lo Fo; Lund, Ole; Palm, Daniel; Sawanpanyalert, Pathom; Sobel, Jeremy; Schlundt, Jørgen
2012-01-01
The rapid advancement of genome technologies holds great promise for improving the quality and speed of clinical and public health laboratory investigations and for decreasing their cost. The latest generation of genome DNA sequencers can provide highly detailed and robust information on disease-causing microbes, and in the near future these technologies will be suitable for routine use in national, regional, and global public health laboratories. With additional improvements in instrumentation, these next- or third-generation sequencers are likely to replace conventional culture-based and molecular typing methods to provide point-of-care clinical diagnosis and other essential information for quicker and better treatment of patients. Provided there is free-sharing of information by all clinical and public health laboratories, these genomic tools could spawn a global system of linked databases of pathogen genomes that would ensure more efficient detection, prevention, and control of endemic, emerging, and other infectious disease outbreaks worldwide. PMID:23092707
Continental hydrology loading observed by VLBI measurements
NASA Astrophysics Data System (ADS)
Eriksson, David; MacMillan, D. S.
2014-07-01
Variations in continental water storage lead to loading deformation of the crust with typical peak-to-peak variations at very long baseline interferometry (VLBI) sites of 3-15 mm in the vertical component and 1-2 mm in the horizontal component. The hydrology signal at VLBI sites has annual and semi-annual components and clear interannual variations. We have calculated the hydrology loading series using mass loading distributions derived from the global land data assimilation system (GLDAS) hydrology model and alternatively from a global grid of equal-area gravity recovery and climate experiment (GRACE) mascons. In the analysis of the two weekly VLBI 24-h R1 and R4 network sessions from 2003 to 2010 the baseline length repeatabilities are reduced in 79 % (80 %) of baselines when GLDAS (GRACE) loading corrections are applied. Site vertical coordinate repeatabilities are reduced in about 80 % of the sites when either GLDAS or GRACE loading is used. In the horizontal components, reduction occurs in 70-80 % of the sites. Estimates of the annual site vertical amplitudes were reduced for 16 out of 18 sites if either loading series was applied. We estimated loading admittance factors for each site and found that the average admittances were 1.01 0.05 for GRACE and 1.39 0.07 for GLDAS. The standard deviations of the GRACE admittances and GLDAS admittances were 0.31 and 0.68, respectively. For sites that have been observed in a set of sufficiently temporally dense daily sessions, the average correlation between VLBI vertical monthly averaged series and GLDAS or GRACE loading series was 0.47 and 0.43, respectively.
How Cognitive Load Influences Speakers' Choice of Referring Expressions.
Vogels, Jorrig; Krahmer, Emiel; Maes, Alfons
2015-08-01
We report on two experiments investigating the effect of an increased cognitive load for speakers on the choice of referring expressions. Speakers produced story continuations to addressees, in which they referred to characters that were either salient or non-salient in the discourse. In Experiment 1, referents that were salient for the speaker were non-salient for the addressee, and vice versa. In Experiment 2, all discourse information was shared between speaker and addressee. Cognitive load was manipulated by the presence or absence of a secondary task for the speaker. The results show that speakers under load are more likely to produce pronouns, at least when referring to less salient referents. We take this finding as evidence that speakers under load have more difficulties taking discourse salience into account, resulting in the use of expressions that are more economical for themselves. © 2014 Cognitive Science Society, Inc.
Thermal elastohydrodynamic lubrication of spur gears
NASA Technical Reports Server (NTRS)
Wang, K. L.; Cheng, H. S.
1980-01-01
An analysis and computer program called TELSGE were developed to predict the variations of dynamic load, surface temperature, and lubricant film thickness along the contacting path during the engagement of a pair of involute spur gears. The analysis of dynamic load includes the effect of gear inertia, the effect of load sharing of adjacent teeth, and the effect of variable tooth stiffness which are obtained by a finite-element method. Results obtained from TELSGE for the dynamic load distributions along the contacting path for various speeds of a pair of test gears show patterns similar to that observed experimentally. Effects of damping ratio, contact ratio, tip relief, and tooth error on the dynamic load were examined. In addition, two dimensionless charts are included for predicting the maximum equilibrium surface temperature, which can be used to estimate directly the lubricant film thickness based on well established EHD analysis.
Facility or Facilities? That is the Question.
NASA Astrophysics Data System (ADS)
Viso, M.
2018-04-01
The management of the martian samples upon arrival on the Earth will require a lot of work to ensure a safe life detection and biohazard testing during the quarantine. This will induce a sharing of the load between several facilities.
Airport Information Retrieval System (AIRS) User's Guide
DOT National Transportation Integrated Search
1973-08-01
The handbook is a user's guide for a prototype air traffic flow control automation system developed for the FAA's System Command Center. The system is implemented on a time-sharing computer and is designed to provide airport traffic load predictions ...
Airport Information Retrieval System (AIRS) System Support Manual
DOT National Transportation Integrated Search
1973-01-01
This handbook is a support manual for prototype air traffic flow control automation system developed for the FAA's Systems Command Center. The system is implemented on a time-sharing computer and is designed to provide airport traffic load prediction...
Scaling up the global nursing health workforce: contributions of an international organization.
Rukholm, Ellen E; Stamler, Lynnette Leeseberg; Talbot, Lise R; Bednash, Geraldine; Raines, Fay; Potempa, Kathleen; Nugent, Pauline; Clark, Dame Jill Macleod; Bernhauser, Sue; Parfitt, Barbara
2009-01-01
In this paper key highlights of the scholarly work presented at the Toronto 2008 Global Alliance for Nursing Education & Scholarship (GANES) conference are summarized, challenges opportunities and issues facing nursing education globally arising from the conference discourse are outlined and initial steps are suggested as a way forward to a shared global view of baccalaureate and graduate nursing education and scholarship. This shared view arises from beginning understandings of the issues and opportunities we face globally starting with and building upon the lessons learned from the literature and from the experiences of nursing educators and nursing education organization locally, regionally, nationally and internationally. The theme of the groundbreaking GANES Toronto conference was "Educating the future nursing and health workforce: A global challenge". One hundred seventy delegates from 17 countries attended the event, with over 80 papers presented. A primary focus of GANES is the contribution of a strategic alliance of national nursing education organizations to contribute to nursing education leading practices and policy that address the scaling up of global nursing and health workforce. The founding members of GANES see a clear link between a strong educational infrastructure and strong scholarship activities in nursing and the ability of a society to be healthy and prosperous. Evidence presented at the recent GANES conference supports that belief. Through the strength of partnerships and other capacity-building efforts, member countries can support each other to address the global nursing education and health challenges while respecting the local issues.
Load Balancing Strategies for Multiphase Flows on Structured Grids
NASA Astrophysics Data System (ADS)
Olshefski, Kristopher; Owkes, Mark
2017-11-01
The computation time required to perform large simulations of complex systems is currently one of the leading bottlenecks of computational research. Parallelization allows multiple processing cores to perform calculations simultaneously and reduces computational times. However, load imbalances between processors waste computing resources as processors wait for others to complete imbalanced tasks. In multiphase flows, these imbalances arise due to the additional computational effort required at the gas-liquid interface. However, many current load balancing schemes are only designed for unstructured grid applications. The purpose of this research is to develop a load balancing strategy while maintaining the simplicity of a structured grid. Several approaches are investigated including brute force oversubscription, node oversubscription through Message Passing Interface (MPI) commands, and shared memory load balancing using OpenMP. Each of these strategies are tested with a simple one-dimensional model prior to implementation into the three-dimensional NGA code. Current results show load balancing will reduce computational time by at least 30%.
NASA Technical Reports Server (NTRS)
Kalluri, Sreeramesh; Abdul-Aziz, Ali; Mcgaw, Michael A.
1991-01-01
The influence of secondary orientation on the elastic response of a zone axis (001)-oriented nickel-base single-crystal superalloy, PWA 1480, was investigated under mechanical loading conditions by applying finite element techniques. Elastic stress analyses were performed with a commercially available finite element code. Secondary orientation of the single-crystal superalloy was offset with respect to the global coordinate system in increments from 0 to 90 deg and stresses developed within the single crystal were determined for each loading condition. The results indicated that the stresses were strongly influenced by the angular offset between the secondary crystal orientation and the global coordinate system. The degree of influence was found to vary with the type of loading condition (mechanical, thermal, or combined) imposed on the single-crystal superalloy.
NASA Technical Reports Server (NTRS)
Wu, Xiaoping; Argus, Donald F.; Heflin, Michael B.; Ivins, Erik R.; Webb, Frank H.
2002-01-01
Precise GPS measurements of elastic relative site displacements due to surface mass loading offer important constraints on global surface mass transport. We investigate effects of site distribution and aliasing by higher-degree (n greater than or equal 2) loading terms on inversion of GPS data for n = 1 load coefficients and geocenter motion. Covariance and simulation analyses are conducted to assess the sensitivity of the inversion to aliasing and mismodeling errors and possible uncertainties in the n = 1 load coefficient determination. We found that the use of center-of-figure approximation in the inverse formulation could cause 10- 15% errors in the inverted load coefficients. n = 1 load estimates may be contaminated significantly by unknown higher-degree terms, depending on the load scenario and the GPS site distribution. The uncertainty in n = 1 zonal load estimate is at the level of 80 - 95% for two load scenarios.
NASA Astrophysics Data System (ADS)
Li, Zhen; Yue, Jianping; Li, Wang; Lu, Dekai; Li, Xiaogen
2017-08-01
The 0.5° × 0.5° gridded hydrological loading from Global Land Surface Discharge Model (LSDM) mass distributions is adopted for 32 GPS sites on the Eurasian plate from January 2010 to January 2014. When the heights of these sites that have been corrected for the effects of non-tidal atmospheric and ocean loading are adjusted by the hydrological loading deformation, more than one third of the root-mean-square (RMS) values of the GPS height variability become larger. After analyzing the results by continuous wavelet transform (CWT) and wavelet transform coherence (WTC), we confirm that hydrological loading primarily contributes to the annual variations in GPS heights. Further, the cross wavelet transform (XWT) is used to investigate the relative phase between the time series of GPS heights and hydrological deformation, and it is indicated that the annual oscillations in the two time series are physically related for some sites; other geophysical effect, GPS systematic errors and hydrological modeling errors could result in the phase asynchrony between GPS and hydrological loading signals for the other sites. Consequently, the phase asynchrony confirms that the annual fluctuations in GPS observations result from a combination of geophysical signals and systematic errors.
Norman, Luke J; Carlisi, Christina O; Christakou, Anastasia; Cubillo, Ana; Murphy, Clodagh M; Chantiluke, Kaylita; Simmons, Andrew; Giampietro, Vincent; Brammer, Michael; Mataix-Cols, David; Rubia, Katya
2017-01-01
Patients with Attention-Deficit/Hyperactivity Disorder (ADHD) and obsessive/compulsive disorder (OCD) share problems with sustained attention, and are proposed to share deficits in switching between default mode and task positive networks. The aim of this study was to investigate shared and disorder-specific brain activation abnormalities during sustained attention in the two disorders. Twenty boys with ADHD, 20 boys with OCD and 20 age-matched healthy controls aged between 12 and 18 years completed a functional magnetic resonance imaging (fMRI) version of a parametrically modulated sustained attention task with a progressively increasing sustained attention load. Performance and brain activation were compared between groups. Only ADHD patients were impaired in performance. Group by sustained attention load interaction effects showed that OCD patients had disorder-specific middle anterior cingulate underactivation relative to controls and ADHD patients, while ADHD patients showed disorder-specific underactivation in left dorsolateral prefrontal cortex/dorsal inferior frontal gyrus (IFG). ADHD and OCD patients shared left insula/ventral IFG underactivation and increased activation in posterior default mode network relative to controls, but had disorder-specific overactivation in anterior default mode regions, in dorsal anterior cingulate for ADHD and in anterior ventromedial prefrontal cortex for OCD. In sum, ADHD and OCD patients showed mostly disorder-specific patterns of brain abnormalities in both task positive salience/ventral attention networks with lateral frontal deficits in ADHD and middle ACC deficits in OCD, as well as in their deactivation patterns in medial frontal DMN regions. The findings suggest that attention performance in the two disorders is underpinned by disorder-specific activation patterns.
Roldan, Paola C; Jung, Rex E; Sibbitt, Wilmer L; Qualls, Clifford R; Flores, Ranee A; Roldan, Carlos A
2018-06-13
Neurocognitive dysfunction and brain injury on magnetic resonance imaging (MRI) are common in patients with systemic lupus erythematosus (SLE) and are associated with increased morbidity and mortality. However, brain MRI is expensive, is restricted by payers, and requires high expertise. Neurocognitive assessment is an easily available, safe, and inexpensive clinical tool that may select patients needing brain MRI. In this cross-sectional and controlled study, 76 SLE patients (69 women, age 37 ± 12 years) and 26 age and gender-matched healthy subjects (22 women, age 34 ± 11 years) underwent assessment of attention, memory, processing speed, executive function, motor function, and global neurocognitive function. All subjects underwent brain MRI with T1-weighted, fluid-attenuated inversion recovery (FLAIR), and diffusion-weighted imaging. Hemispheric and whole brain lesion load in cm 3 were determined using semi-automated methods. Neurocognitive z-scores in all clinical domains were significantly lower and whole brain and right and left hemispheres brain lesion load were significantly greater in patients than in controls (all p ≤ 0.02). There was significant correlation between neurocognitive z-scores in all domains and whole brain lesion load: processing speed (r = - 0.46; p < 0.0001), attention (r = - 0.42; p < 0.001), memory (r = - 0.40; p = 0.0004), executive function (r = - 0.25; p = 0.03), motor function (r = - 0.25; p = 0.05), and global neurocognitive function (r = - 0.38; p = 0.006). Similar correlations were found for brain hemisphere lesion loads (all p ≤ 0.05). These correlations were strengthened when adjusted for glucocorticoid therapy and SLE disease activity index. Finally, global neurocognitive z-score and erythrosedimentation rate were the only independent predictors of whole brain lesion load (both p ≤ 0.007). Neurocognitive measures and brain lesion load are worse in SLE patients than in controls. In SLE patients, neurocognitive z-scores correlate negatively with and independently predict brain lesion load. Therefore, neurocognitive testing may be an effective clinical tool to select patients needing brain MRI.
Biomechanical and biological aspects of defect treatment in fractures using helical plates.
Perren, S M; Regazzoni, P; Fernandez, A A D
2014-01-01
The clinical case of figure 1 through figure 11 shows a series of impressive failures of plate fixation. The plates were repeatedly applied bridging a comminuted bone segment in a heavy patient. The biomechanical analysis elaborates why this happened and proposes an unconventional procedure to prevent this failure with a minimally invasive procedure. A plate bridging an open gap or a defect in a long bone diaphysis is exposed to full functional load. According to clinical observations such plate application often fails even without external load such as weight bearing. The plate risks to break through fatigue when exposed during a long time to cyclic loading. This type of failure has been observed even with broad plates as well in femoral as in tibiae. The first option to avoid such failure consists in protecting the plate by installing load sharing between plate and either bone or an additional implant. This reduces the load carried by the plate to a safe level. Load sharing with bone may be installed at surgery by establishing solid mechanical bridge between the two main fragments of the fractured bone. The optimal load sharing relies on a solid compressed contact between the main fragments. It can be established because the bone is able to take a large load which results in optimal protection of the plate. In the case of an extended comminuted bone segment it may be very difficult, traumatizing and inefficient to reconstruct the bone. In the present case it was impossible to establish load sharing through the bone. The second option protecting the plate is provided by callus bridging of the gap or defect. The formation of a solid callus bridge takes time but the fatigue failure of the plate also takes time. Therefore, the callus bridge may prevent a late fatigue failure. The surgeon may select one of several options: - Replacing the lack of bone support using a second plate which immediately alleviates plate loading. The drawback of application of a second conventional plate is the extent of surgical trauma at the critical site of healing. - Shingling and/or applying an autologous cancellous bone graft: This procedure provides initially no relevant load sharing but will do so after a couple of weeks. The mechanical coupling of the comparably soft graft and the main fracture fragments presents little problems. Applying a cortical bone graft: Such a graft does provide initial only small load sharing and does a less good job inducing callus than a cancellous graft. Furthermore, the coupling by callus between a somewhat rigid bone graft and the mobile main fracture fragments requires a solid maintained contact. If the cortical graft is fixed using implants with small contact area to the graft such as screws or cerclage loops, the local stress may be critical and the graft may break. When the cortical graft is fixed with cerclage wires the procedure must take into account the limited strength of the individual cerclage. Therefore multiple and well-spaced cerclages are required and may lead to success especially if an intramedullary component of the implant contributes to protection (6). The degree of unloading depends apparently on the stiffness of the material of the protecting splint. Though, more important is the effect of the dimensions of the splint. While titanium as a material is about 50% less stiff than steel, the thickness of the implant changes the stiffness with the third power. That is doubling the thickness results in eightfold increased stiffness. When considering the unloading by application of a second plate the leverage of the second plate plays an important role. The larger the distance between the axis of bending and the second implant the larger the protecting effect. The helical plate (2, 3, 7) as introduced by A.A.D. Fernandez offers biological and mechanical advantages. It can be applied without touching the fracture site maintaining the critical biology intact and provides mechanically efficient unloading. Its application is fairly simple: The helical plate is modified conventional long and small plate that is twisted between its ends about 90 degrees. The twist is applied using "bending irons" (4, 5, 8) whereby the force required is small and the exact degree of twist is not critical. Therefore the twist is applicable operating bending irons by hand. Assuming a situation where a plate bridging a defect or non-union has failed the broken plate is replaced by a similar implant: At the distal end of the bone fracture and opposite to the surgical approach a small incision allows to slide in the helical plate in such a way that proximally the plate ends on the same side of the limb as the replaced plate. Ideally the two plate ends meet and the application of the helical plate does not ask for an additional surgical exposure at this location. Otherwise a small minimally invasive exposure is required. The helical plate is then fixed to the main bone fragments using a couple of locked screws. The following case demonstrates the use and efficiency of the helical plate saving a situation where multiple attempts using conventional plates had failed. The successful final treatment of this case was performed by A. A. D. Fernandez.
While increased anthropogenic nutrient loading of coastal ecosystems is a growing ecological and economic problem both in the U.S. and globally, the extent of such excess nutrient loading in Pacific Northwest estuaries is poorly known. To help determine the vulnerability of Pacif...
ERIC Educational Resources Information Center
Wagner, Alan
2006-01-01
Higher education globalizes: its potential contributions are now seen as a crucial component of cross-border economic competitiveness. Accumulating evidence suggests that a highly qualified workforce contributes substantially to a nation's economic competitiveness, particularly when a large share of the workforce has acquired skills and knowledge…
American Students Abroad Can't Be "Global Citizens"
ERIC Educational Resources Information Center
Zemach-Bersin, Talya
2008-01-01
A student shares experiences of her semester-long Tibetan-studies program in India, Nepal, and Tibet. Informed by both home university and program provider that by going abroad and immersing herself in a foreign culture, she would become a "global citizen," she was encouraged to "act like the locals," "be a resident,"…
ERIC Educational Resources Information Center
Rolbin, Cyrus; Chiesa, Bruno Della
2010-01-01
The "language-culture tesseract" hypothesized in the September 2010 issue of "Mind, Brain, and Education" suggests successive links between non-native language (NNL) acquisition, the development of cross-cultural empathy, and prosocial global ethics. Invoking Goethe's (1833/1999) aphorism, "those who do not know other languages know nothing of…
Periodicals Price Survey 2008: Embracing Openness
ERIC Educational Resources Information Center
Van Orsdel, Lee C.; Born, Kathleen
2008-01-01
Evidence for open access as an emergent, global state of mind is everywhere. The "New York Times" went "open" last September, and the "Wall Street Journal" is slated to follow. Increasingly, scholarly communities are breaking with tradition and calling for the open sharing of research, software, and data. Amongst these global initiatives is the…
ERIC Educational Resources Information Center
Kerlin, Steven C.; Carlsen, William S.; Kelly, Gregory J.; Goehring, Elizabeth
2013-01-01
The conception of Global Learning Communities (GLCs) was researched to discover potential benefits of the use of online technologies that facilitated communication and scientific data sharing outside of the normal classroom setting. 1,419 students in 635 student groups began the instructional unit. Students represented the classrooms of 33…
Teach for All: Storytelling "Shared Solutions" and Scaling Global Reform
ERIC Educational Resources Information Center
Ahmann, Chloe
2015-01-01
"Teach For All" is a global network of state-based organizations that translate "Teach For America's" market model of school reform into moral projects of nation-building abroad. Referring to this challenge as one of "scaling" the organization, its leaders elaborate a theory of change that hinges on replicability: in…
Debriefing in Moodle: Written Feedback on Trust and Knowledge Sharing in a Social Dilemma Game
ERIC Educational Resources Information Center
Oertig, Margaret
2010-01-01
This article describes a new approach to debriefing that uses the discussion forum feature of the Moodle open source course management system to debrief a simulation game with undergraduate business students. The simulation game allowed the students to experience the fragility of trust when sharing knowledge in a global virtual project team. I…
Final Report: Sensorpedia Phase 3
DOE Office of Scientific and Technical Information (OSTI.GOV)
Gorman, Bryan L; Resseguie, David R
2011-02-01
This report is a summary of the Oak Ridge National Laboratory s (ORNL s) Phase 3 development of Sensorpedia, a sensor information sharing platform. Sensorpedia is ORNL s Wikipedia for Sensors. The overall goal of Sensorpedia is to enable global scale sensor information sharing for scientific research, national security and defense, public health and safety, emergency preparedness and response, and general community awareness and outreach.
Federal Register 2010, 2011, 2012, 2013, 2014
2010-04-12
... Approval of a Proposed Rule Change, as Modified by Amendment No. 1 Thereto, Relating to the Listing of Mars...-4 thereunder,\\2\\ a proposed rule change to list and trade shares (``Shares'') of the Mars Hill... with ``Mars Hill Global Relative Value ETF'' and that all references in the filing to ``HTE Asset...
ERIC Educational Resources Information Center
Foster, Catherine; McMenemy, David
2012-01-01
Thirty-six ethical codes from national professional associations were studied, the aim to test whether librarians have global shared values or if political and cultural contexts have significantly influenced the codes' content. Gorman's eight core values of stewardship, service, intellectual freedom, rationalism, literacy and learning, equity of…
Federal Register 2010, 2011, 2012, 2013, 2014
2011-01-25
... Proposed Rule Change To Impose a Quarterly Maximum on the Listing of Additional Shares Fees Payable by... Terms of Substance of the Proposed Rule Change Nasdaq proposes to impose a quarterly maximum on the.... 5910. The NASDAQ Global Market (a) No change. (b) Additional Shares (1)-(5) No change. (6) The maximum...
Overexcitability and Optimal Flow in Talented Dancers, Singers, and Athletes
ERIC Educational Resources Information Center
Thomson, Paula; Jaque, S. Victoria
2016-01-01
Overexcitability (OE) and optimal flow are variables shared by talented individuals. This study demonstrated that the dancer (n = 86) and opera singer (n = 61) groups shared higher OE profiles compared to the athlete group (n = 50). Two self-report instruments assessed flow (global and subscales) and the five OE dimensions. All groups endorsed…
Open Architecture Data System for NASA Langley Combined Loads Test System
NASA Technical Reports Server (NTRS)
Lightfoot, Michael C.; Ambur, Damodar R.
1998-01-01
The Combined Loads Test System (COLTS) is a new structures test complex that is being developed at NASA Langley Research Center (LaRC) to test large curved panels and cylindrical shell structures. These structural components are representative of aircraft fuselage sections of subsonic and supersonic transport aircraft and cryogenic tank structures of reusable launch vehicles. Test structures are subjected to combined loading conditions that simulate realistic flight load conditions. The facility consists of two pressure-box test machines and one combined loads test machine. Each test machine possesses a unique set of requirements or research data acquisition and real-time data display. Given the complex nature of the mechanical and thermal loads to be applied to the various research test articles, each data system has been designed with connectivity attributes that support both data acquisition and data management functions. This paper addresses the research driven data acquisition requirements for each test machine and demonstrates how an open architecture data system design not only meets those needs but provides robust data sharing between data systems including the various control systems which apply spectra of mechanical and thermal loading profiles.
Significance of aerosol radiative effect in energy balance control on global precipitation change
DOE Office of Scientific and Technical Information (OSTI.GOV)
Suzuki, Kentaroh; Stephens, Graeme L.; Golaz, Jean-Christophe
Historical changes of global precipitation in the 20th century simulated by a climate model are investigated. The results simulated with alternate configurations of cloud microphysics are analyzed in the context of energy balance controls on global precipitation, where the latent heat changes associated with the precipitation change is nearly balanced with changes to atmospheric radiative cooling. The atmospheric radiative cooling is dominated by its clear-sky component, which is found to correlate with changes to both column water vapor and aerosol optical depth (AOD). The water vapor-dependent component of the clear-sky radiative cooling is then found to scale with global temperaturemore » change through the Clausius–Clapeyron relationship. This component results in a tendency of global precipitation increase with increasing temperature at a rate of approximately 2%K -1. Another component of the clear-sky radiative cooling, which is well correlated with changes to AOD, is also found to vary in magnitude among different scenarios with alternate configurations of cloud microphysics that controls the precipitation efficiency, a major factor influencing the aerosol scavenging process that can lead to different aerosol loadings. These results propose how different characteristics of cloud microphysics can cause different aerosol loadings that in turn perturb global energy balance to significantly change global precipitation. This implies a possible coupling of aerosol–cloud interaction with aerosol–radiation interaction in the context of global energy balance.« less
Significance of aerosol radiative effect in energy balance control on global precipitation change
Suzuki, Kentaroh; Stephens, Graeme L.; Golaz, Jean-Christophe
2017-10-17
Historical changes of global precipitation in the 20th century simulated by a climate model are investigated. The results simulated with alternate configurations of cloud microphysics are analyzed in the context of energy balance controls on global precipitation, where the latent heat changes associated with the precipitation change is nearly balanced with changes to atmospheric radiative cooling. The atmospheric radiative cooling is dominated by its clear-sky component, which is found to correlate with changes to both column water vapor and aerosol optical depth (AOD). The water vapor-dependent component of the clear-sky radiative cooling is then found to scale with global temperaturemore » change through the Clausius–Clapeyron relationship. This component results in a tendency of global precipitation increase with increasing temperature at a rate of approximately 2%K -1. Another component of the clear-sky radiative cooling, which is well correlated with changes to AOD, is also found to vary in magnitude among different scenarios with alternate configurations of cloud microphysics that controls the precipitation efficiency, a major factor influencing the aerosol scavenging process that can lead to different aerosol loadings. These results propose how different characteristics of cloud microphysics can cause different aerosol loadings that in turn perturb global energy balance to significantly change global precipitation. This implies a possible coupling of aerosol–cloud interaction with aerosol–radiation interaction in the context of global energy balance.« less
Global estimation of CO emissions using three sets of satellite data for burned area
NASA Astrophysics Data System (ADS)
Jain, Atul K.
Using three sets of satellite data for burned areas together with the tree cover imagery and a biogeochemical component of the Integrated Science Assessment Model (ISAM) the global emissions of CO and associated uncertainties are estimated for the year 2000. The available fuel load (AFL) is calculated using the ISAM biogeochemical model, which accounts for the aboveground and surface fuel removed by land clearing for croplands and pasturelands, as well as the influence on fuel load of various ecosystem processes (such as stomatal conductance, evapotranspiration, plant photosynthesis and respiration, litter production, and soil organic carbon decomposition) and important feedback mechanisms (such as climate and fertilization feedback mechanism). The ISAM estimated global total AFL in the year 2000 was about 687 Pg AFL. All forest ecosystems account for about 90% of the global total AFL. The estimated global CO emissions based on three global burned area satellite data sets (GLOBSCAR, GBA, and Global Fire Emissions Database version 2 (GFEDv2)) for the year 2000 ranges between 320 and 390 Tg CO. Emissions from open fires are highest in tropical Africa, primarily due to forest cutting and burning. The estimated overall uncertainty in global CO emission is about ±65%, with the highest uncertainty occurring in North Africa and Middle East region (±99%). The results of this study suggest that the uncertainties in the calculated emissions stem primarily from the area burned data.
Vaccines, our shared responsibility.
Pagliusi, Sonia; Jain, Rishabh; Suri, Rajinder Kumar
2015-05-05
The Developing Countries Vaccine Manufacturers' Network (DCVMN) held its fifteenth annual meeting from October 27-29, 2014, New Delhi, India. The DCVMN, together with the co-organizing institution Panacea Biotec, welcomed over 240 delegates representing high-profile governmental and nongovernmental global health organizations from 36 countries. Over the three-day meeting, attendees exchanged information about their efforts to achieve their shared goal of preventing death and disability from known and emerging infectious diseases. Special praise was extended to all stakeholders involved in the success of polio eradication in South East Asia and highlighted challenges in vaccine supply for measles-rubella immunization over the coming decades. Innovative vaccines and vaccine delivery technologies indicated creative solutions for achieving global immunization goals. Discussions were focused on three major themes including regulatory challenges for developing countries that may be overcome with better communication; global collaborations and partnerships for leveraging investments and enable uninterrupted supply of affordable and suitable vaccines; and leading innovation in vaccines difficult to develop, such as dengue, Chikungunya, typhoid-conjugated and EV71, and needle-free technologies that may speed up vaccine delivery. Moving further into the Decade of Vaccines, participants renewed their commitment to shared responsibility toward a world free of vaccine-preventable diseases. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.
Sedyaningsih, Endang R; Isfandari, Siti; Soendoro, Triono; Supari, Siti Fadilah
2008-06-01
As the country hardest hit by avian influenza, both in poultry and in human, Indonesia's decision to withhold samples of avian influenza virus A (H5N1) has fired up a global controversy. The objective of this paper is to describe the position taken by Indonesia in the events leading to the decision and in those conducted to resolve the situation. The sources for this paper are the Indonesian human influenza A(H5N1) case reports and study results, summaries, minutes and reports of national and international meetings of virus sharing, and other related Indonesian and WHO documents. The International Health Regulations 2005 have been applied in different ways based on different interpretations. While one party insists on the importance of free, non-conditional, virus sharing for risk assessment and risk response, Indonesia--as supported by most of the developing countries--stresses on the more basic principles such as sovereignty of a country over its biological materials, transparency of the global system, and equity between developed and developing nations. This event demonstrates the unresolved imbalance between the affluent high-tech countries and the poor agriculture-based countries. Regional, global and in-country meetings must continue to be conducted to find solutions acceptable to all.
CYP2C19 variant mitigates Alzheimer disease pathophysiology in vivo and postmortem.
Benedet, Andréa L; Yu, Lei; Labbe, Aurélie; Mathotaarachchi, Sulantha; Pascoal, Tharick A; Shin, Monica; Kang, Min-Su; Gauthier, Serge; Rouleau, Guy A; Poirier, Judes; Bennett, David A; Rosa-Neto, Pedro
2018-02-01
To verify whether CYP polymorphisms are associated with amyloid-β (Aβ) pathology across the spectrum of clinical Alzheimer disease using in vivo and postmortem data from 2 independent cohorts. A candidate-gene approach tested the association between 5 genes (28 single nucleotide polymorphisms) and Aβ load measured in vivo by the global [ 18 F]florbetapir PET standardized uptake value ratio (SUVR) in 338 Alzheimer's Disease Neuroimaging Initiative participants. Significant results were then tested using plasma Aβ and CSF Aβ and Aβ/phosphorylated tau (Aβ/p-tau) ratio in the same cohort. The significant association was also generalized to postmortem Aβ load measurement in the Rush Religious Orders Study/Memory and Aging Project cohorts. In addition, global cognition was used as a phenotype in the analysis in both cohorts. Analysis of Aβ PET identified a variant in the CYP2C19 gene (rs4388808; p = 0.0006), in which carriers of the minor allele (MA) had a lower global SUVR. A voxel-wise analysis revealed that the variant is associated with a lower Aβ load in the frontal, inferior temporal, and posterior cingulate cortices. MA carriers also had higher CSF Aβ ( p = 0.003) and Aβ/p-tau ratio ( p = 0.02) but had no association with Aβ plasma levels. In postmortem brains, MA carriers had a lower Aβ load ( p = 0.03). Global cognition was higher in MA carriers, which was found to be mediated by Aβ. Together, these findings point to an association between CYP2C19 polymorphism and Aβ pathology, suggesting a protective effect of the MA of rs4388808. Despite the several possibilities in which CYP2C19 affects brain Aβ, the biological mechanism by which this genetic variation may act as a protective factor merits further investigation.
So, Winnie K. W.; Chan, Raymond Javan; Truant, Tracy; Trevatt, Paul; Bialous, Stella Aguinaga; Barton-Burke, Margaret
2016-01-01
This paper examines cancer health disparities and contributing factors at national, regional, and international levels. The authors all live in different countries and regions with different health-care systems and practices. Despite the shared cancer nursing perspective, each country or global region approaches cancer disparities differently. With globalization the world is becoming smaller, and in turn becoming interconnected and interdependent. This article focuses on cancer health disparities and global cancer nursing, exemplifying these concepts about the impact and implications of person-centered care. PMID:28083548
Hume, Samuel; Chow, Anthony; Evans, Julie; Malfait, Frederik; Chason, Julie; Wold, J. Darcy; Kubick, Wayne; Becnel, Lauren B.
2018-01-01
The Clinical Data Interchange Standards Consortium (CDISC) is a global non-profit standards development organization that creates consensus-based standards for clinical and translational research. Several of these standards are now required by regulators for electronic submissions of regulated clinical trials’ data and by government funding agencies. These standards are free and open, available for download on the CDISC Website as PDFs. While these documents are human readable, they are not amenable to ready use by electronic systems. CDISC launched the CDISC Shared Health And Research Electronic library (SHARE) to provide the standards metadata in machine-readable formats to facilitate the automated management and implementation of the standards. This paper describes how CDISC SHARE’S standards can facilitate collecting, aggregating and analyzing standardized data from early design to end analysis; and its role as a central resource providing information systems with metadata that drives process automation including study setup and data pipelining. PMID:29888049
Zhou, Tian-shu; Chu, Jian; Araki, Kenji; Yoshihara, Hiroyuki
2011-01-01
Objective At present, most clinical data are exchanged between organizations within a regional system. However, people traveling abroad may need to visit a hospital, which would make international exchange of clinical data very useful. Background Since 2007, a collaborative effort to achieve clinical data sharing has been carried out at Zhejiang University in China and Kyoto University and Miyazaki University in Japan; each is running a regional clinical information center. Methods An international layer system named Global Dolphin was constructed with several key services, sharing patients' health information between countries using a medical markup language (MML). The system was piloted with 39 test patients. Results The three regions above have records for 966 000 unique patients, which are available through Global Dolphin. Data exchanged successfully from Japan to China for the 39 study patients include 1001 MML files and 152 images. The MML files contained 197 free text-type paragraphs that needed human translation. Discussion The pilot test in Global Dolphin demonstrates that patient information can be shared across countries through international health data exchange. To achieve cross-border sharing of clinical data, some key issues had to be addressed: establishment of a super directory service across countries; data transformation; and unique one—language translation. Privacy protection was also taken into account. The system is now ready for live use. Conclusion The project demonstrates a means of achieving worldwide accessibility of medical data, by which the integrity and continuity of patients' health information can be maintained. PMID:21571747
Coggins, Brian E.; Werner-Allen, Jonathan W.; Yan, Anthony; Zhou, Pei
2012-01-01
In structural studies of large proteins by NMR, global fold determination plays an increasingly important role in providing a first look at a target’s topology and reducing assignment ambiguity in NOESY spectra of fully-protonated samples. In this work, we demonstrate the use of ultrasparse sampling, a new data processing algorithm, and a 4-D time-shared NOESY experiment (1) to collect all NOEs in 2H/13C/15N-labeled protein samples with selectively-protonated amide and ILV methyl groups at high resolution in only four days, and (2) to calculate global folds from this data using fully automated resonance assignment. The new algorithm, SCRUB, incorporates the CLEAN method for iterative artifact removal, but applies an additional level of iteration, permitting real signals to be distinguished from noise and allowing nearly all artifacts generated by real signals to be eliminated. In simulations with 1.2% of the data required by Nyquist sampling, SCRUB achieves a dynamic range over 10000:1 (250× better artifact suppression than CLEAN) and completely quantitative reproduction of signal intensities, volumes, and lineshapes. Applied to 4-D time-shared NOESY data, SCRUB processing dramatically reduces aliasing noise from strong diagonal signals, enabling the identification of weak NOE crosspeaks with intensities 100× less than diagonal signals. Nearly all of the expected peaks for interproton distances under 5 Å were observed. The practical benefit of this method is demonstrated with structure calculations for 23 kDa and 29 kDa test proteins using the automated assignment protocol of CYANA, in which unassigned 4-D time-shared NOESY peak lists produce accurate and well-converged global fold ensembles, whereas 3-D peak lists either fail to converge or produce significantly less accurate folds. The approach presented here succeeds with an order of magnitude less sampling than required by alternative methods for processing sparse 4-D data. PMID:22946863
NASA Astrophysics Data System (ADS)
Hasenkopf, C. A.
2012-12-01
Collaborative science in which scientists are able to form research questions based on the current body of scientific knowledge and get feedback from colleagues on their ideas and work is essential for pushing science forward. However, not all scientists are able to fully participate in the international science community. Scientists from developing countries can face barriers to communicating with the international community due to, among other issues: fewer scientists in their home country, difficulty in getting language-specific science writing training, fewer established pre-existing international collaborations and networks, and sometimes geographic isolation. These barriers not only result in keeping individual scientists from contributing their ideas, but they also slow down the progress of the scientific enterprise for everyone. Global Science Share (http://globalscienceshare.org/) is a new project, entering its pilot phase in Fall 2012, which will work to reduce this disparity by connecting young scientists and engineers from developing countries seeking to improve their technical writing with other scientists and engineers around the world via online collaborations. Scientist-volunteers act as mentors and are paired up with mentees according to their academic field and writing needs. The mentors give feedback and constructive technical and editorial criticisms on mentees' submitted pieces of writing through a four-step email discussion. Mentees gain technical writing skills, as well as make international connections with other scientists and engineers in fields related to their own. Mentors also benefit by gaining new international scientific colleagues and honing their own writing skills through their critiques. The Global Science Share project will begin its pilot phase by first inviting Mongolian science students to apply as mentees this fall. This abstract will introduce the Global Science Share program, present a progress report from its first semester, and inform members of the geoscience community about this unique outreach opportunity to help strengthen and widen the international science community that can be done in the comfort of one's office or home.
Attention induced neural response trade-off in retinotopic cortex under load.
Torralbo, Ana; Kelley, Todd A; Rees, Geraint; Lavie, Nilli
2016-09-14
The effects of perceptual load on visual cortex response to distractors are well established and various phenomena of 'inattentional blindness' associated with elimination of visual cortex response to unattended distractors, have been documented in tasks of high load. Here we tested an account for these effects in terms of a load-induced trade-off between target and distractor processing in retinotopic visual cortex. Participants were scanned using fMRI while performing a visual-search task and ignoring distractor checkerboards in the periphery. Retinotopic responses to target and distractors were assessed as a function of search load (comparing search set-sizes two, three and five). We found that increased load not only increased activity in frontoparietal network, but also had opposite effects on retinotopic responses to target and distractors. Target-related signals in areas V2-V3 linearly increased, while distractor response linearly decreased, with increased load. Critically, the slopes were equivalent for both load functions, thus demonstrating resource trade-off. Load effects were also found in displays with the same item number in the distractor hemisphere across different set sizes, thus ruling out local intrahemispheric interactions as the cause. Our findings provide new evidence for load theory proposals of attention resource sharing between target and distractor leading to inattentional blindness.
Attention induced neural response trade-off in retinotopic cortex under load
Torralbo, Ana; Kelley, Todd A.; Rees, Geraint; Lavie, Nilli
2016-01-01
The effects of perceptual load on visual cortex response to distractors are well established and various phenomena of ‘inattentional blindness’ associated with elimination of visual cortex response to unattended distractors, have been documented in tasks of high load. Here we tested an account for these effects in terms of a load-induced trade-off between target and distractor processing in retinotopic visual cortex. Participants were scanned using fMRI while performing a visual-search task and ignoring distractor checkerboards in the periphery. Retinotopic responses to target and distractors were assessed as a function of search load (comparing search set-sizes two, three and five). We found that increased load not only increased activity in frontoparietal network, but also had opposite effects on retinotopic responses to target and distractors. Target-related signals in areas V2–V3 linearly increased, while distractor response linearly decreased, with increased load. Critically, the slopes were equivalent for both load functions, thus demonstrating resource trade-off. Load effects were also found in displays with the same item number in the distractor hemisphere across different set sizes, thus ruling out local intrahemispheric interactions as the cause. Our findings provide new evidence for load theory proposals of attention resource sharing between target and distractor leading to inattentional blindness. PMID:27625311
Mitchell, Daniel J; Cusack, Rhodri
2011-01-01
An electroencephalographic (EEG) marker of the limited contents of human visual short-term memory (VSTM) has previously been described. Termed contralateral delay activity, this consists of a sustained, posterior, negative potential that correlates with memory load and is greatest contralateral to the remembered hemifield. The current investigation replicates this finding and uses magnetoencephalography (MEG) to characterize its magnetic counterparts and their neural generators as they evolve throughout the memory delay. A parametric manipulation of memory load, within and beyond capacity limits, allows separation of signals that asymptote with behavioral VSTM performance from additional responses that contribute to a linear increase with set-size. Both EEG and MEG yielded bilateral signals that track the number of objects held in memory, and contralateral signals that are independent of memory load. In MEG, unlike EEG, the contralateral interaction between hemisphere and item load is much weaker, suggesting that bilateral and contralateral markers of memory load reflect distinct sources to which EEG and MEG are differentially sensitive. Nonetheless, source estimation allowed both the bilateral and the weaker contralateral capacity-limited responses to be localized, along with a load-independent contralateral signal. Sources of global and hemisphere-specific signals all localized to the posterior intraparietal sulcus during the early delay. However the bilateral load response peaked earlier and its generators shifted later in the delay. Therefore the hemifield-specific response may be more closely tied to memory maintenance while the global load response may be involved in initial processing of a limited number of attended objects, such as their individuation or consolidation into memory.
Srinivasan, Narayanan; Mukherjee, Sumitava; Mishra, Maruti V.; Kesarwani, Smriti
2013-01-01
Attention is a key process used to conceptualize and define modes of thought, but we lack information about the role of specific attentional processes on preferential choice and memory in multi-attribute decision making. In this study, we examine the role of attention based on two dimensions, attentional scope and load on choice preference strength and memory using a paradigm that arguably elicits unconscious thought. Scope of attention was manipulated by using global or local processing during distraction (Experiment 1) and before the information-encoding stage (Experiment 2). Load was manipulated by using the n-back task in Experiment 1. Results from Experiment 1 show that global processing or distributed attention during distraction results in stronger preference irrespective of load but better memory only at low cognitive load. Task difficulty or load did not have any effect on preference or memory. In Experiment 2, distributed attention before attribute encoding facilitated only memory but did not influence preference. Results show that attentional processes at different stages of processing like distraction and information-encoding influence decision making processes. Scope of attention not only influences preference and memory but the manner in which attentional scope influences them depends on both load and stage of information processing. The results indicate the important role of attention in processes critical for decision making and calls for a re-evaluation of the unconscious thought theory (UTT) and the need for reconceptualizing the role of attention. PMID:23382726
Enhanced water use efficiency in global terrestrial ecosystems under increasing aerosol loadings
DOE Office of Scientific and Technical Information (OSTI.GOV)
Lu, Xiaoliang; Chen, Min; Liu, Yaling
Aerosols play a crucial role in the climate system, affecting incoming radiation and cloud formation. Based on a modelling framework that couples ecosystem processes with the atmospheric transfer of radiation, we analyze the effect of aerosols on surface incoming radiation, gross primary productivity (GPP), water losses from ecosystems through evapotranspiration (ET) and ecosystem water use efficiency (WUE, defined as GPP/ET) for 2003–2010 and validate them at global FLUXNET sites. The total diffuse radiation increases under relatively low or intermediate aerosol loadings, but decreases under more polluted conditions. We find that aerosol-induced changes in GPP depend on leaf area index, aerosolmore » loading and cloudiness. Specifically, low and moderate aerosol loadings cause increases in GPP for all plant types, while heavy aerosol loadings result in enhancement (decrease) in GPP for dense (sparse) vegetation. On the other hand, ET is mainly negatively affected by aerosol loadings due to the reduction in total incoming radiation. Finally, WUE shows a consistent rise in all plant types under increasing aerosol loadings. Overall, the simulated daily WUE compares well with observations at 43 eddy-covariance tower sites (R 2=0.84 and RMSE=0.01gC (kg H 2O) -1) with better performance at forest sites. In addition to the increasing portions of diffuse light, the rise in WUE is also favored by the reduction in radiation- and heat-stress caused by the aerosols, especially for wet and hot climates.« less
Srinivasan, Narayanan; Mukherjee, Sumitava; Mishra, Maruti V; Kesarwani, Smriti
2013-01-01
Attention is a key process used to conceptualize and define modes of thought, but we lack information about the role of specific attentional processes on preferential choice and memory in multi-attribute decision making. In this study, we examine the role of attention based on two dimensions, attentional scope and load on choice preference strength and memory using a paradigm that arguably elicits unconscious thought. Scope of attention was manipulated by using global or local processing during distraction (Experiment 1) and before the information-encoding stage (Experiment 2). Load was manipulated by using the n-back task in Experiment 1. Results from Experiment 1 show that global processing or distributed attention during distraction results in stronger preference irrespective of load but better memory only at low cognitive load. Task difficulty or load did not have any effect on preference or memory. In Experiment 2, distributed attention before attribute encoding facilitated only memory but did not influence preference. Results show that attentional processes at different stages of processing like distraction and information-encoding influence decision making processes. Scope of attention not only influences preference and memory but the manner in which attentional scope influences them depends on both load and stage of information processing. The results indicate the important role of attention in processes critical for decision making and calls for a re-evaluation of the unconscious thought theory (UTT) and the need for reconceptualizing the role of attention.
Detection of anthropogenic dust using CALIPSO lidar measurements
NASA Astrophysics Data System (ADS)
Huang, J. P.; Liu, J. J.; Chen, B.; Nasiri, S. L.
2015-10-01
Anthropogenic dusts are those produced by human activities on disturbed soils, which are mainly cropland, pastureland, and urbanized regions, and are a subset of the total dust load which includes natural sources from desert regions. Our knowledge of anthropogenic dusts is still very limited due to a lack of data. To understand the contribution of anthropogenic dust to the total global dust load, it is important to identify it apart from total dust. In this study, a new technique for distinguishing anthropogenic dust from natural dust is proposed by using Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) dust and planetary boundary layer (PBL) height retrievals along with a land use data set. Using this technique, the global distribution of dust is analyzed and the relative contribution of anthropogenic and natural dust sources to regional and global emissions are estimated. Results reveal that local anthropogenic dust aerosol due to human activity, such as agriculture, industrial activity, transportation, and overgrazing, accounts for about 25 % of the global continental dust load. Of these anthropogenic dust aerosols, more than 53 % come from semi-arid and semi-wet regions. Annual mean anthropogenic dust column burden (DCB) values range from 0.42 g m-2, with a maximum in India, to 0.12 g m-2, with a minimum in North America. A better understanding of anthropogenic dust emission will enable us to focus on human activities in these critical regions and with such knowledge we will be more able to improve global dust models and to explore the effects of anthropogenic emission on radiative forcing, climate change, and air quality in the future.
The substorm cycle as reproduced by global MHD models
NASA Astrophysics Data System (ADS)
Gordeev, E.; Sergeev, V.; Tsyganenko, N.; Kuznetsova, M.; Rastäetter, L.; Raeder, J.; Tóth, G.; Lyon, J.; Merkin, V.; Wiltberger, M.
2017-01-01
Recently, Gordeev et al. (2015) suggested a method to test global MHD models against statistical empirical data. They showed that four community-available global MHD models supported by the Community Coordinated Modeling Center (CCMC) produce a reasonable agreement with reality for those key parameters (the magnetospheric size, magnetic field, and pressure) that are directly related to the large-scale equilibria in the outer magnetosphere. Based on the same set of simulation runs, here we investigate how the models reproduce the global loading-unloading cycle. We found that in terms of global magnetic flux transport, three examined CCMC models display systematically different response to idealized 2 h north then 2 h south interplanetary magnetic field (IMF) Bz variation. The LFM model shows a depressed return convection and high loading rate during the growth phase as well as enhanced return convection and high unloading rate during the expansion phase, with the amount of loaded/unloaded magnetotail flux and the growth phase duration being the closest to their observed empirical values during isolated substorms. Two other models exhibit drastically different behavior. In the BATS-R-US model the plasma sheet convection shows a smooth transition to the steady convection regime after the IMF southward turning. In the Open GGCM a weak plasma sheet convection has comparable intensities during both the growth phase and the following slow unloading phase. We also demonstrate potential technical problem in the publicly available simulations which is related to postprocessing interpolation and could affect the accuracy of magnetic field tracing and of other related procedures.
The Substorm Cycle as Reproduced by Global MHD Models
NASA Technical Reports Server (NTRS)
Gordeev, E.; Sergee, V.; Tsyganenko, N.; Kuznetsova, M.; Rastaetter, Lutz; Raeder, J.; Toth, G.; Lyon, J.; Merkin, V.; Wiltberger, M.
2017-01-01
Recently, Gordeev et al. (2015) suggested a method to test global MHD models against statistical empirical data. They showed that four community-available global MHD models supported by the Community Coordinated Modeling Center (CCMC) produce a reasonable agreement with reality for those key parameters (the magnetospheric size, magnetic field, and pressure) that are directly related to the large-scale equilibria in the outer magnetosphere. Based on the same set of simulation runs, here we investigate how the models reproduce the global loading-unloading cycle. We found that in terms of global magnetic flux transport, three examined CCMC models display systematically different response to idealized2 h north then 2 h south interplanetary magnetic field (IMF) Bz variation. The LFM model shows a depressed return convection and high loading rate during the growth phase as well as enhanced return convection and high unloading rate during the expansion phase, with the amount of loaded unloaded magnetotail flux and the growth phase duration being the closest to their observed empirical values during isolated substorms. Two other models exhibit drastically different behavior. In the BATS-R-US model the plasma sheet convection shows a smooth transition to the steady convection regime after the IMF southward turning. In the Open GGCM a weak plasma sheet convection has comparable intensities during both the growth phase and the following slow unloading phase. We also demonstrate potential technical problem in the publicly available simulations which is related to post processing interpolation and could affect the accuracy of magnetic field tracing and of other related procedures.
NASA Technical Reports Server (NTRS)
Rebbechi, Brian; Forrester, B. David; Oswald, Fred B.; Townsend, Dennis P.
1992-01-01
A comparison was made between computer model predictions of gear dynamics behavior and experimental results. The experimental data were derived from the NASA gear noise rig, which was used to record dynamic tooth loads and vibration. The experimental results were compared with predictions from the DSTO Aeronautical Research Laboratory's gear dynamics code for a matrix of 28 load speed points. At high torque the peak dynamic load predictions agree with the experimental results with an average error of 5 percent in the speed range 800 to 6000 rpm. Tooth separation (or bounce), which was observed in the experimental data for light torque, high speed conditions, was simulated by the computer model. The model was also successful in simulating the degree of load sharing between gear teeth in the multiple tooth contact region.
A novel strategy for load balancing of distributed medical applications.
Logeswaran, Rajasvaran; Chen, Li-Choo
2012-04-01
Current trends in medicine, specifically in the electronic handling of medical applications, ranging from digital imaging, paperless hospital administration and electronic medical records, telemedicine, to computer-aided diagnosis, creates a burden on the network. Distributed Service Architectures, such as Intelligent Network (IN), Telecommunication Information Networking Architecture (TINA) and Open Service Access (OSA), are able to meet this new challenge. Distribution enables computational tasks to be spread among multiple processors; hence, performance is an important issue. This paper proposes a novel approach in load balancing, the Random Sender Initiated Algorithm, for distribution of tasks among several nodes sharing the same computational object (CO) instances in Distributed Service Architectures. Simulations illustrate that the proposed algorithm produces better network performance than the benchmark load balancing algorithms-the Random Node Selection Algorithm and the Shortest Queue Algorithm, especially under medium and heavily loaded conditions.
Hay, Julia L; Milders, Maarten M; Sahraie, Arash; Niedeggen, Michael
2006-08-01
Recent visual marking studies have shown that the carry-over of distractor inhibition can impair the ability of singletons to capture attention if the singleton and distractors share features. The current study extends this finding to first-order motion targets and distractors, clearly separated in time by a visual cue (the letter X). Target motion discrimination was significantly impaired, a result attributed to the carry-over of distractor inhibition. Increasing the difficulty of cue detection increased the motion target impairment, as distractor inhibition is thought to increase under demanding (high load) conditions in order to maximize selection efficiency. The apparent conflict with studies reporting reduced distractor inhibition under high load conditions was resolved by distinguishing between the effects of "cognitive" and "perceptual" load. ((c) 2006 APA, all rights reserved).
Data sharing as social dilemma: Influence of the researcher’s personality
2017-01-01
It is widely acknowledged that data sharing has great potential for scientific progress. However, so far making data available has little impact on a researcher’s reputation. Thus, data sharing can be conceptualized as a social dilemma. In the presented study we investigated the influence of the researcher's personality within the social dilemma of data sharing. The theoretical background was the appropriateness framework. We conducted a survey among 1564 researchers about data sharing, which also included standardized questions on selected personality factors, namely the so-called Big Five, Machiavellianism and social desirability. Using regression analysis, we investigated how these personality domains relate to four groups of dependent variables: attitudes towards data sharing, the importance of factors that might foster or hinder data sharing, the willingness to share data, and actual data sharing. Our analyses showed the predictive value of personality for all four groups of dependent variables. However, there was not a global consistent pattern of influence, but rather different compositions of effects. Our results indicate that the implications of data sharing are dependent on age, gender, and personality. In order to foster data sharing, it seems advantageous to provide more personal incentives and to address the researchers’ individual responsibility. PMID:28817642
Karasik, David; Demissie, Serkalem; Lu, Darlene; Broe, Kerry E; Boyd, Steven K; Liu, Ching-Ti; Hsu, Yi-Hsiang; Bouxsein, Mary L; Kiel, Douglas P
2017-11-01
Genetic factors contribute to the risk of bone fractures, partly because of effects on bone strength. High-resolution peripheral quantitative computed tomography (HR-pQCT) estimates bone strength using micro-finite element analysis (µFEA). The goal of this study was to investigate if the bone failure load estimated by HR-pQCT-based µFEA is heritable and to what extent it shares genetic regulation with areal bone mineral density (aBMD). Bone microarchitecture was measured by HR-pQCT at the ultradistal tibia and ultradistal radius in adults from the Framingham Heart Study (n = 1087, mean age 72 years; 57% women). Radial and tibial failure load in compression were estimated by µFEA. Femoral neck (FN) and ultradistal forearm (UD) aBMD were measured by dual-energy X-ray absorptiometry (DXA). Heritability (h 2 ) of failure load and aBMD and genetic correlations between them was estimated adjusting for covariates (age and sex). Failure load values at the non-weight-bearing ultradistal radius and at the weight-bearing ultradistal tibia were highly correlated (r = 0.906; p < 0.001). Estimates of h 2 adjusted for covariates were 0.522 for the radius and 0.497 for the tibia. Additional adjustment for height did not impact on the h 2 results, but adjustment for aBMD at the UD and FN somewhat decreased h 2 point estimates: 0.222 and 0.380 for radius and tibia, respectively. In bivariate analysis, there was a high phenotypic and genetic correlation between covariate-adjusted failure load at the radius and UD aBMD (ρ P = 0.826, ρ G = 0.954, respectively), whereas environmental correlations were lower (ρ E = 0.696), all highly significant (p < 0.001). Similar correlations were observed between tibial failure load and femoral neck aBMD (ρ P = 0.577, ρ G = 0.703, both p < 0.001; ρ E = 0.432, p < 0.05). These data from adult members of families from a population-based cohort suggest that bone strength of distal extremities estimated by micro-finite element analysis is heritable and shares some genetic composition with areal BMD, regardless of the skeletal site. © 2017 American Society for Bone and Mineral Research. © 2017 American Society for Bone and Mineral Research.
Effectiveness of barnyard best management practices in Wisconsin
Stuntebeck, Todd D.; Bannerman, Roger T.
1998-01-01
In 1978, the Wisconsin Legislature committed to protecting water quality by enacting the Nonpoint Source Water Pollution Abatement Program. Through this program, cost-share money is provided within priority watersheds to control sources of nonpoint pollution. Most of the cost-share dollars for rural watersheds have been used to implement barnyard Best Management Practices (BMPs) because barnyards are believed to be a major source of pollutants, most notably phosphorus. Reductions in phosphorus loads of as much as 95 percent have been predicted for the barnyard BMPs recommended for priority watersheds.
Hartman, Emily A; McCarthy, Robert J; Labato, Mary A
2017-01-01
A 10-year-old neutered male domestic shorthair cat was evaluated because of signs of stertorous breathing and reverse sneezing of 8 months' duration. A CT scan performed 1 week before evaluation indicated nasopharyngeal stenosis or collapse. Increased respiratory effort, stertorous breathing, coughing, reverse sneezing, bilateral black ocular discharge and mucoid left nasal discharge were noted. Rhinoscopy suggested possible nasopharyngeal stenosis. Balloon dilation was attempted but unsuccessful. Ventral rhinotomy was performed the following day using a spring-loaded mouth gag to access the surgical site. After rhinotomy, the patient had neurologic signs attributed to global cerebral ischemia that progressed to respiratory arrest, subsequently resulting in euthanasia. While ischemic brain injury has been associated with the use of a spring-loaded mouth gag in cats, to our knowledge this is the first reported instance where use resulted in respiratory arrest culminating in euthanasia.
Implementation of GAMMON - An efficient load balancing strategy for a local computer system
NASA Technical Reports Server (NTRS)
Baumgartner, Katherine M.; Kling, Ralph M.; Wah, Benjamin W.
1989-01-01
GAMMON (Global Allocation from Maximum to Minimum in cONstant time), an efficient load-balancing algorithm, is described. GAMMON uses the available broadcast capability of multiaccess networks to implement an efficient search technique for finding hosts with maximal and minimal loads. The search technique has an average overhead which is independent of the number of participating stations. The transition from the theoretical concept to a practical, reliable, and efficient implementation is described.
I/O load balancing for big data HPC applications
DOE Office of Scientific and Technical Information (OSTI.GOV)
Paul, Arnab K.; Goyal, Arpit; Wang, Feiyi
High Performance Computing (HPC) big data problems require efficient distributed storage systems. However, at scale, such storage systems often experience load imbalance and resource contention due to two factors: the bursty nature of scientific application I/O; and the complex I/O path that is without centralized arbitration and control. For example, the extant Lustre parallel file system-that supports many HPC centers-comprises numerous components connected via custom network topologies, and serves varying demands of a large number of users and applications. Consequently, some storage servers can be more loaded than others, which creates bottlenecks and reduces overall application I/O performance. Existing solutionsmore » typically focus on per application load balancing, and thus are not as effective given their lack of a global view of the system. In this paper, we propose a data-driven approach to load balance the I/O servers at scale, targeted at Lustre deployments. To this end, we design a global mapper on Lustre Metadata Server, which gathers runtime statistics from key storage components on the I/O path, and applies Markov chain modeling and a minimum-cost maximum-flow algorithm to decide where data should be placed. Evaluation using a realistic system simulator and a real setup shows that our approach yields better load balancing, which in turn can improve end-to-end performance.« less
Global nutrient cycles have been altered by use of fossil fuels and fertilizers resulting in increases in nutrient loads to aquatic systems. In the United States, excess nutrients have been repeatedly reported as the primary cause of lake water quality impairments. Setting nutr...
CERN data services for LHC computing
NASA Astrophysics Data System (ADS)
Espinal, X.; Bocchi, E.; Chan, B.; Fiorot, A.; Iven, J.; Lo Presti, G.; Lopez, J.; Gonzalez, H.; Lamanna, M.; Mascetti, L.; Moscicki, J.; Pace, A.; Peters, A.; Ponce, S.; Rousseau, H.; van der Ster, D.
2017-10-01
Dependability, resilience, adaptability and efficiency. Growing requirements require tailoring storage services and novel solutions. Unprecedented volumes of data coming from the broad number of experiments at CERN need to be quickly available in a highly scalable way for large-scale processing and data distribution while in parallel they are routed to tape for long-term archival. These activities are critical for the success of HEP experiments. Nowadays we operate at high incoming throughput (14GB/s during 2015 LHC Pb-Pb run and 11PB in July 2016) and with concurrent complex production work-loads. In parallel our systems provide the platform for the continuous user and experiment driven work-loads for large-scale data analysis, including end-user access and sharing. The storage services at CERN cover the needs of our community: EOS and CASTOR as a large-scale storage; CERNBox for end-user access and sharing; Ceph as data back-end for the CERN OpenStack infrastructure, NFS services and S3 functionality; AFS for legacy distributed-file-system services. In this paper we will summarise the experience in supporting LHC experiments and the transition of our infrastructure from static monolithic systems to flexible components providing a more coherent environment with pluggable protocols, tuneable QoS, sharing capabilities and fine grained ACLs management while continuing to guarantee dependable and robust services.
Force sharing in high-power parallel servo-actuators
NASA Technical Reports Server (NTRS)
Neal, T. P.
1974-01-01
The various existing force sharing schemes were examined by conducting a literature survey. A list of potentially applicable concepts was compiled from this survey, and a brief analysis was then made of each concept, which resulted in two competing schemes being selected for in-depth evaluation. A functional design of the equalization logic for the two schemes was undertaken and specific space shuttle application was chosen for experimental evaluation. The application was scaled down so that existing hardware could be utilized. Next, an analog computer study was conducted to evaluate the more important characteristics of the two competing force sharing schemes. On the basis of the computers study, a final configuration was selected. A load simulator was then designed to evaluate this configuration on actual hardware.
Federal Register 2010, 2011, 2012, 2013, 2014
2012-09-05
... the Listing and Trading of Shares of the WisdomTree Global Corporate Bond Fund of the WisdomTree Trust... of the WisdomTree Global Corporate Bond Fund (``Fund'') of the WisdomTree Trust (``Trust'') under...) (SR-NASDAQ-2012-004) (order approving listing and trading of WisdomTree Emerging Markets Corporate...
ERIC Educational Resources Information Center
Velten, Justin C.
2015-01-01
Expatriate preparation is an ever growing area of interest in a globalized economy sharing a globalized workforce. For decades, scholars have sought methods for best preparing expatriates for host culture experiences. Research has revealed an array of factors leading to intercultural readiness success which has led to the creation of various…
Developing a global aeronautical satellite system
NASA Technical Reports Server (NTRS)
Dement, Donald K.
1988-01-01
Arinc, an airline industry-owned and operated company in the United States, has taken steps toward establishing a global aeronautical satellite communications system. Plans call for initiation of a thin-route data operation in 1989, upgrading to establish voice communications via shared spot-beam transponders carried on other satellites, and deploying a worldwide network using dedicated satellites by 1994.
ERIC Educational Resources Information Center
Streitwieser, Bernhard, Ed.
2014-01-01
Continuous and rapid developments in global higher education today more than ever before present new questions, greater challenges, and vast new opportunities for institutions, policy makers, scholars and students alike. This book is a collection of studies and essays by many of the leading experts in international higher education who share their…
Trade Liberalization and Women's Integration into National Labor Markets: A Cross-Country Analysis
ERIC Educational Resources Information Center
Meyer, Lisa B.
2006-01-01
This paper examines the effects of trade liberalization and the risks associated with participation in the global trading system on women's integration into national labor markets. Using data from 1970 to 1995, I identify two global determinants of the female share of national labor markets: trade openness and transnational corporate penetration.…
ERIC Educational Resources Information Center
Tucker-Drob, Elliot M.; Reynolds, Chandra A.; Finkel, Deborah; Pedersen, Nancy L.
2014-01-01
Aging-related declines occur in many different domains of cognitive function during middle and late adulthood. However, whether a global dimension underlies individual differences in changes in different domains of cognition and whether global genetic influences on cognitive changes exist is less clear. We addressed these issues by applying…
A Global Effort for Educational Equity
ERIC Educational Resources Information Center
Dzulkifli, Dzameer
2015-01-01
A look at Teach For All's global work through the lens of Teach For Malaysia one of several dozen organizations around the world inspired by Teach For America and Teach First to share solutions as they adapt a common approach to tackle education inequality in their home countries. A deeper look at Malaysian education brought Teach For Malaysia to…
ERIC Educational Resources Information Center
Nordgren, R. D.
2006-01-01
A multi-site case study of three Swedish schools examined the dimensions of trust, responsibility, shared power (democracy), and global workforce competence as required by a decade-old national education reforms. A key finding was the existence of progressive educational practices including constructivist epistemology, evidenced by the schools'…
Global Injustice, Pedagogy and Democratic Iterations: Some Reflections on Why Teachers Matter
ERIC Educational Resources Information Center
Unterhalter, Elaine
2017-01-01
The article argues teachers matter because of their potential to engage in critical reflection on values associated with connecting the local, the national and the global. Their practice can support those who are dislocated, and who have no place. Teachers matter because they can help us understand how we share humanity and aspirations across many…
ERIC Educational Resources Information Center
Medina, Carmen L.; Wohlwend, Karen E.
2014-01-01
This book takes on current perspectives on children's relationships to literacy, media, childhood, markets and transtionalism in converging global worlds. It introduces the idea of multi-sited imaginaries to explain how children's media and literacy performances shape and are shaped by shared visions of communities that we collectively imagine,…
Literature and Public Discourse in Times of Global Unrest.
ERIC Educational Resources Information Center
Lindblom, Kenneth
2003-01-01
Notes English teachers already do communal, even global, work whether or not they are conscious of doing so. Examines both positive and negative consequences of that work and suggests ways of understanding it most effectively. Presents ideas on the theme of this issue, "Talking Literature." Shares a brief essay by Wail S. Hassan in which…
ERIC Educational Resources Information Center
Moll, Marita, Ed.
If the public policy goal to connect all schools to the information highway becomes a reality, public education as Canadians have known it--a shared social responsibility and a generally shared social experience--could be lost. This volume of contributed papers brings into focus the new context within which the struggle to technologize education…
Kristin Vanderbilt; John H. Porter; Sheng-Shan Lu; Nic Bertrand; David Blankman; Xuebing Guo; Honglin He; Don Henshaw; Karpjoo Jeong; Eun-Shik Kim; Chau-Chin Lin; Margaret O' Brien; Takeshi Osawa; Éamonn Ó Tuama; Wen Su; Haibo Yang
2017-01-01
Shared ecological data have the potential to revolutionize ecological research just as shared genetic sequence data have done for biological research. However, for ecological data to be useful, it must first be discoverable. A broad-scale research topic may require that a researcher be able to locate suitable data from a variety of global, regional and national data...
Report to Congress on the Strategic Defense Initiative, 1992
1992-07-01
1.4.3 Shared View on Defenses .............................................................. 1-6 1.5 U.S. Contribution to a Global Defense System...including, in our view , that such defenses would not threaten existing deterrents--and the willingness of the U.S. to extend protection to allies...representing the central government as well as several Republics, the presentation was positively received. 1.4.3 Shared View on Defenses President
High altitude environmental monitoring: the SHARE project and CEOP-HE
NASA Astrophysics Data System (ADS)
Tartari, G.
2009-04-01
Mountain areas above 2,500 m a.s.l. constitute about 25% of the Earth's surface and play a fundamental role in the global water balance, while influencing global climate and atmospheric circulation systems. Several millions, including lowlanders, are directly affected by the impacts of climate change on glaciers and water resource distribution. Mountains and high altitude plateaus are subject to the highest rate of temperature increase (e.g., Tibetan Plateau) and are recognized as particularly vulnerable to the effects of climate change. In spite of this, the number of permanent monitoring sites in the major environmental networks decreases with altitude. On a sample of two hundred high altitude automatic weather stations located above 2,500 m a.s.l., less than 20% are over 4,000 m, while there are only 24 stations in the world that could be considered "complete" high altitude observatories. Furthermore, entire mountain areas are left uncovered, creating significant data gaps which make reliable modelling and forecasting nearly impossible. In response to these problems, Ev-K2-CNR has developed the project SHARE (Stations at High Altitude for Research on the Environment) with the support of the Italian government and in collaboration with UNEP. This integrated environmental monitoring and research project aims to improve knowledge on the local, regional and global consequences of climate change in mountain regions and on the influence of high elevations on climate, atmospheric circulation and hydrology. SHARE today boasts a network of 13 permanent monitoring stations between 2,165 m and 8,000 m. Affiliated researchers have produced over 150 scientific publications in atmospheric sciences, meteorology and climate, glaciology, limnology and paleolimnology and geophysics. SHARE network data is also contributed to international programs (UNEP-ABC, WMO-GAW, WCRP-GEWEX-CEOP, NASA-AERONET, ILTER, EU-EUSAAR, EU-ACCENT). Within this context, the CEOP-High Elevations (CEOP-HE) element of regional focus was developed under the GEWEX CEOP programme to study multi-scale variability in water and energy cycles in high elevation areas, and to help improve observations, modelling and data management. Future plans include expansion of the SHARE network, addition of other key research areas including hydrology, and creation of mechanisms to favour exchange of data amongst high altitude networks. In coordination with other global research and monitoring projects (CliC, etc.), SHARE and CEOP-HE could provide a more organic and well-distributed interdisciplinary network, thus allowing governments and international agencies to better face impacts of climate change effects on energy and water budgets and elaborate appropriate adaptation strategies.
Anderson, Ariana E; Marder, Stephen; Reise, Steven P; Savitz, Adam; Salvadore, Giacomo; Fu, Dong Jing; Li, Qingqin; Turkoz, Ibrahim; Han, Carol; Bilder, Robert M
2018-02-06
Common genetic variation spans schizophrenia, schizoaffective and bipolar disorders, but historically, these syndromes have been distinguished categorically. A symptom dimension shared across these syndromes, if such a general factor exists, might provide a clearer target for understanding and treating mental illnesses that share core biological bases. We tested the hypothesis that a bifactor model of the Positive and Negative Syndrome Scale (PANSS), containing 1 general factor and 5 specific factors (positive, negative, disorganized, excited, anxiety), explains the cross-diagnostic structure of symptoms better than the traditional 5-factor model, and examined the extent to which a general factor reflects the overall severity of symptoms spanning diagnoses in 5094 total patients with a diagnosis of schizophrenia, schizoaffective, and bipolar disorder. The bifactor model provided superior fit across diagnoses, and was closer to the "true" model, compared to the traditional 5-factor model (Vuong test; P < .001). The general factor included high loadings on 28 of the 30 PANSS items, omitting symptoms associated with the excitement and anxiety/depression domains. The general factor had highest total loadings on symptoms that are often associated with the positive and disorganization syndromes, but there were also substantial loadings on the negative syndrome thus leading to the interpretation of this factor as reflecting generalized psychosis. A bifactor model derived from the PANSS can provide a stronger framework for measuring cross-diagnostic psychopathology than a 5-factor model, and includes a generalized psychosis dimension shared at least across schizophrenia, schizoaffective, and bipolar disorder. © The Author(s) 2018. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center. All rights reserved. For permissions, please email: journals.permissions@oup.com
The global dimensions of public health preparedness and implications for US action.
Moore, Melinda
2012-06-01
The globalization of public health is both real and relevant throughout the United States and to Americans traveling or residing abroad. US public policy responses are evolving, but a crisper and more comprehensive global perspective is needed. I suggest four timely US actions to address today's competing realities of globalization and economic austerity: raise awareness among clinicians and local health departments; capture and share exemplary disaster management practices across countries; ensure that US global health investments are effective, efficient, and sustainable; and think globally while acting locally to enhance US health security. The reauthorization of the Pandemic and All-Hazards Preparedness Act of 2006 provides an opportunity to more clearly address the global dimensions of domestic preparedness.
NASA Astrophysics Data System (ADS)
Vink, Rona; Behrendt, Horst
2002-11-01
Pollutant transport and management in the Rhine and Elbe basins is still of international concern, since certain target levels set by the international committees for protection of both rivers have not been reached. The analysis of the chain of emissions of point and diffuse sources to river loads will provide policy makers with a tool for effective management of river basins. The analysis of large river basins such as the Elbe and Rhine requires information on the spatial and temporal characteristics of both emissions and physical information of the entire river basin. In this paper, an analysis has been made of heavy metal emissions from various point and diffuse sources in the Rhine and Elbe drainage areas. Different point and diffuse pathways are considered in the model, such as inputs from industry, wastewater treatment plants, urban areas, erosion, groundwater, atmospheric deposition, tile drainage, and runoff. In most cases the measured heavy metal loads at monitoring stations are lower than the sum of the heavy metal emissions. This behaviour in large river systems can largely be explained by retention processes (e.g. sedimentation) and is dependent on the specific runoff of a catchment. Independent of the method used to estimate emissions, the source apportionment analysis of observed loads was used to determine the share of point and diffuse sources in the heavy metal load at a monitoring station by establishing a discharge dependency. The results from both the emission analysis and the source apportionment analysis of observed loads were compared and gave similar results. Between 51% (for Hg) and 74% (for Pb) of the total transport in the Elbe basin is supplied by inputs from diffuse sources. In the Rhine basin diffuse source inputs dominate the total transport and deliver more than 70% of the total transport. The diffuse hydrological pathways with the highest share are erosion and urban areas.
Global surgery: current evidence for improving surgical care.
Fuller, Jennifer C; Shaye, David A
2017-08-01
The field of global surgery is undergoing rapid transformation, owing to several recent prominent reports positioning it as a cost-effective means of relieving global disease burden. The purpose of this article is to review the recent advances in the field of global surgery. Efforts to grow the global surgical workforce and procedural capacity have focused on innovative methods to increase surgeon training, enhance international collaboration, leverage technology, optimize existing health systems, and safely implement task-sharing. Computer modeling offers a novel means of informing policy to optimize timely access to care, equitably promote health and financial protection, and efficiently grow infrastructure. Tools and checklists have recently been developed to enhance data collection and ensure methodologically rigorous publications to inform planning, benchmark surgical systems, promote accurate modeling, track key health indicators, and promote safety. Creation of institutional partnerships and trainee exchanges can enrich training, stimulate commitment to humanitarian work, and promote the equal exchange of ideas and expertise. The recent body of work creates a strong foundation upon which work toward the goal of universal access to safe, affordable surgical care can be built; however, further collection and analysis of country-specific data is necessary for accurate modeling and outcomes research into the efficacy of policies such as task-sharing is greatly needed.
Vila-Castelar, Clara; Ly, Jenny J; Kaplan, Lillian; Van Dyk, Kathleen; Berger, Jeffrey T; Macina, Lucy O; Stewart, Jennifer L; Foldi, Nancy S
2018-04-09
Donepezil is widely used to treat Alzheimer's disease (AD), but detecting early response remains challenging for clinicians. Acetylcholine is known to directly modulate attention, particularly under high cognitive conditions, but no studies to date test whether measures of attention under high load can detect early effects of donepezil. We hypothesized that load-dependent attention tasks are sensitive to short-term treatment effects of donepezil, while global and other domain-specific cognitive measures are not. This longitudinal, randomized, double-blind, placebo-controlled pilot trial (ClinicalTrials.gov Identifier: NCT03073876) evaluated 23 participants newly diagnosed with AD initiating de novo donepezil treatment (5 mg). After baseline assessment, participants were randomized into Drug (n = 12) or Placebo (n = 11) groups, and retested after approximately 6 weeks. Cognitive assessment included: (a) attention tasks (Foreperiod Effect, Attentional Blink, and Covert Orienting tasks) measuring processing speed, top-down accuracy, orienting, intra-individual variability, and fatigue; (b) global measures (Alzheimer's Disease Assessment Scale-Cognitive Subscale, Mini-Mental Status Examination, Dementia Rating Scale); and (c) domain-specific measures (memory, language, visuospatial, and executive function). The Drug but not the Placebo group showed benefits of treatment at high-load measures by preserving top-down accuracy, improving intra-individual variability, and averting fatigue. In contrast, other global or cognitive domain-specific measures could not detect treatment effects over the same treatment interval. The pilot-study suggests that attention measures targeting accuracy, variability, and fatigue under high-load conditions could be sensitive to short-term cholinergic treatment. Given the central role of acetylcholine in attentional function, load-dependent attentional measures may be valuable cognitive markers of early treatment response.
Lawler, Mark; Siu, Lillian L; Rehm, Heidi L; Chanock, Stephen J; Alterovitz, Gil; Burn, John; Calvo, Fabien; Lacombe, Denis; Teh, Bin Tean; North, Kathryn N; Sawyers, Charles L
2015-11-01
The recent explosion of genetic and clinical data generated from tumor genome analysis presents an unparalleled opportunity to enhance our understanding of cancer, but this opportunity is compromised by the reluctance of many in the scientific community to share datasets and the lack of interoperability between different data platforms. The Global Alliance for Genomics and Health is addressing these barriers and challenges through a cooperative framework that encourages "team science" and responsible data sharing, complemented by the development of a series of application program interfaces that link different data platforms, thus breaking down traditional silos and liberating the data to enable new discoveries and ultimately benefit patients. ©2015 American Association for Cancer Research.
Working with Planetary-Scale Data in the Cloud
NASA Astrophysics Data System (ADS)
Flasher, J.
2017-12-01
When data is shared on AWS, it can be analyzed using AWS on-demand computing resources quickly and efficiently. Users can work with any amount of data without needing to download it or store their own copies. When heavy data like imagery, genomics data, or volumes of sensor data are available in AWS's cloud, the time required to copy the data to a virtual server for analysis is virtually eliminated. AWS's global infrastructure allows data providers to make their data available worldwide and ensure quick access to critical data from anywhere. In this session, we will share lessons learned from our experience supporting a global community of entrepreneurs, students and researchers by making petabytes of data freely available for anyone to use in the cloud.
NASA Astrophysics Data System (ADS)
Tuttle Keane, James; Matsuyama, Isamu; Kamata, Shunichi; Steckloff, Jordan
2016-10-01
The New Horizons flyby of Pluto revealed the dwarf planet to be a strikingly diverse, geologically active world. Perhaps the most intriguing feature on the New Horizons encounter hemisphere is Sputnik Planum—a 1000 km diameter, probable impact basin, filled with several kilometers of actively convecting volatile ices (N2, CH4, CO). One salient characteristic of Sputnik Planum is its curious alignment with the Pluto-Charon tidal axis. The alignment of large geologic features with principal axis of inertia (such as the tidal axis) is the hallmark of global reorientation, i.e. true polar wander. Here we show that the present location of Sputnik Planum is a natural consequence of loading of 1-2 km of volatile ices within the Sputnik Planum basin. Larger volatile ice thicknesses (like those inferred from studies of ice convection within Sputnik Planum) betray an underlying negative gravity anomaly associated with the basin. As Pluto reoriented in response to the loading of volatile ices within Sputnik Planum, stresses accumulated within the lithosphere (as each geographic location experiences a change in tidal/rotational potential). These reorientation stresses, coupled with loading stresses, and stresses from the freezing of a subsurface ocean resulted in the fracturing of Pluto's lithosphere in a characteristic, global pattern of extensional faults. Our predicted pattern of extensional faults due to this reorientation closely replicates the observed distribution of faults on Pluto (more so than global expansion, orbit migration, de-spinning, or loading alone). Sputnik Planum likely formed ~60° northwest of its present location, and was loaded with volatile ices over millions of years due to seasonal volatile transport cycles. This result places Pluto in a truly unique category of planetary bodies where volatiles are not only controlling surface geology and atmospheric processes, but they are also directly controlling the orientation of the entire dwarf planet. Pluto's past, present, and future orientation is controlled by complicated feedbacks between volatile transport, insolation, and interior structure.
Gonneaud, Julie; Kalpouzos, Grégoria; Bon, Laetitia; Viader, Fausto; Eustache, Francis; Desgranges, Béatrice
2011-01-01
Prospective memory (PM) is the ability to remember to perform an action at a specific point in the future. Regarded as multidimensional, PM involves several cognitive functions that are known to be impaired in normal aging. In the present study, we set out to investigate the cognitive correlates of PM impairment in normal aging. Manipulating cognitive load, we assessed event- and time-based PM, as well as several cognitive functions, including executive functions, working memory and retrospective episodic memory, in healthy subjects covering the entire adulthood. We found that normal aging was characterized by PM decline in all conditions and that event-based PM was more sensitive to the effects of aging than time-based PM. Whatever the conditions, PM was linked to inhibition and processing speed. However, while event-based PM was mainly mediated by binding and retrospective memory processes, time-based PM was mainly related to inhibition. The only distinction between high- and low-load PM cognitive correlates lays in an additional, but marginal, correlation between updating and the high-load PM condition. The association of distinct cognitive functions, as well as shared mechanisms with event- and time-based PM confirms that each type of PM relies on a different set of processes. PMID:21678154
Lu, Qiongshi; Li, Boyang; Ou, Derek; Erlendsdottir, Margret; Powles, Ryan L; Jiang, Tony; Hu, Yiming; Chang, David; Jin, Chentian; Dai, Wei; He, Qidu; Liu, Zefeng; Mukherjee, Shubhabrata; Crane, Paul K; Zhao, Hongyu
2017-12-07
Despite the success of large-scale genome-wide association studies (GWASs) on complex traits, our understanding of their genetic architecture is far from complete. Jointly modeling multiple traits' genetic profiles has provided insights into the shared genetic basis of many complex traits. However, large-scale inference sets a high bar for both statistical power and biological interpretability. Here we introduce a principled framework to estimate annotation-stratified genetic covariance between traits using GWAS summary statistics. Through theoretical and numerical analyses, we demonstrate that our method provides accurate covariance estimates, thereby enabling researchers to dissect both the shared and distinct genetic architecture across traits to better understand their etiologies. Among 50 complex traits with publicly accessible GWAS summary statistics (N total ≈ 4.5 million), we identified more than 170 pairs with statistically significant genetic covariance. In particular, we found strong genetic covariance between late-onset Alzheimer disease (LOAD) and amyotrophic lateral sclerosis (ALS), two major neurodegenerative diseases, in single-nucleotide polymorphisms (SNPs) with high minor allele frequencies and in SNPs located in the predicted functional genome. Joint analysis of LOAD, ALS, and other traits highlights LOAD's correlation with cognitive traits and hints at an autoimmune component for ALS. Copyright © 2017 American Society of Human Genetics. Published by Elsevier Inc. All rights reserved.
Involving Research Stakeholders in Developing Policy on Sharing Public Health Research Data in Kenya
Jao, Irene; Kombe, Francis; Mwalukore, Salim; Bull, Susan; Parker, Michael; Kamuya, Dorcas; Molyneux, Sassy
2015-01-01
Increased global sharing of public health research data has potential to advance scientific progress but may present challenges to the interests of research stakeholders, particularly in low-to-middle income countries. Policies for data sharing should be responsive to public views, but there is little evidence of the systematic study of these from low-income countries. This qualitative study explored views on fair data-sharing processes among 60 stakeholders in Kenya with varying research experience, using a deliberative approach. Stakeholders’ attitudes were informed by perceptions of benefit and concerns for research data sharing, including risks of stigmatization, loss of privacy, and undermining scientific careers and validity, reported in detail elsewhere. In this article, we discuss institutional trust-building processes seen as central to perceptions of fairness in sharing research data in this setting, including forms of community involvement, individual prior awareness and agreement to data sharing, independence and accountability of governance mechanisms, and operating under a national framework. PMID:26297748
Sharing health-related data: a privacy test?
Dyke, Stephanie OM; Dove, Edward S; Knoppers, Bartha M
2016-01-01
Greater sharing of potentially sensitive data raises important ethical, legal and social issues (ELSI), which risk hindering and even preventing useful data sharing if not properly addressed. One such important issue is respecting the privacy-related interests of individuals whose data are used in genomic research and clinical care. As part of the Global Alliance for Genomics and Health (GA4GH), we examined the ELSI status of health-related data that are typically considered ‘sensitive’ in international policy and data protection laws. We propose that ‘tiered protection’ of such data could be implemented in contexts such as that of the GA4GH Beacon Project to facilitate responsible data sharing. To this end, we discuss a Data Sharing Privacy Test developed to distinguish degrees of sensitivity within categories of data recognised as ‘sensitive’. Based on this, we propose guidance for determining the level of protection when sharing genomic and health-related data for the Beacon Project and in other international data sharing initiatives. PMID:27990299
Reciprocal Tutoring: Design with Cognitive Load Sharing
ERIC Educational Resources Information Center
Chou, Chih-Yueh; Chan, Tak-Wai
2016-01-01
"Reciprocal tutoring," as reported in "Exploring the design of computer supports for reciprocal tutoring" (Chan and Chou 1997), has extended the meaning and scope of "intelligent tutoring" originally implemented in stand alone computers. This research is a follow-up to our studies on a "learning companion…
40 CFR 1066.210 - Dynamometers.
Code of Federal Regulations, 2014 CFR
2014-07-01
... to recreate the mechanical inertia and frictional forces that a vehicle exerts on road surfaces... drive axles may share a single drive roll. Use good engineering judgment to ensure that the dynamometer... engineering judgment. (3) The load applied by the dynamometer simulates forces acting on the vehicle during...
NORTHEAST LOON STUDY WORKING GROUP PARTNERSHIP TO ASSESS ENVIRONMENTAL RISK
The Northeast Loon Study Working Group (NELSWG) was formed in 1994 to proactively identify threats to one of the Northeast's most popular waterbirds, the common loon, Gavia immer. Seventeen institutions have come together to identify strategy, coordinate the work load, and share ...
"Job-Sharing" Storage of Hydrogen in Ru/Li₂O Nanocomposites.
Fu, Lijun; Tang, Kun; Oh, Hyunchul; Manickam, Kandavel; Bräuniger, Thomas; Chandran, C Vinod; Menzel, Alexander; Hirscher, Michael; Samuelis, Dominik; Maier, Joachim
2015-06-10
A "job-sharing" hydrogen storage mechanism is proposed and experimentally investigated in Ru/Li2O nanocomposites in which H(+) is accommodated on the Li2O side, while H(-) or e(-) is stored on the side of Ru. Thermal desorption-mass spectroscopy results show that after loading with D2, Ru/Li2O exhibits an extra desorption peak, which is in contrast to Ru nanoparticles or ball-milled Li2O alone, indicating a synergistic hydrogen storage effect due to the presence of both phases. By varying the ratio of the two phases, it is shown that the effect increases monotonically with the area of the heterojunctions, indicating interface related hydrogen storage. X-ray diffraction, Fourier transform infrared spectroscopy, and nuclear magnetic resonance results show that a weak LiO···D bond is formed after loading in Ru/Li2O nanocomposites with D2. The storage-pressure curve seems to favor H(+)/H(-) over H(+)/e(-) mechanism.
Data traffic reduction schemes for sparse Cholesky factorizations
NASA Technical Reports Server (NTRS)
Naik, Vijay K.; Patrick, Merrell L.
1988-01-01
Load distribution schemes are presented which minimize the total data traffic in the Cholesky factorization of dense and sparse, symmetric, positive definite matrices on multiprocessor systems with local and shared memory. The total data traffic in factoring an n x n sparse, symmetric, positive definite matrix representing an n-vertex regular 2-D grid graph using n (sup alpha), alpha is equal to or less than 1, processors are shown to be O(n(sup 1 + alpha/2)). It is O(n(sup 3/2)), when n (sup alpha), alpha is equal to or greater than 1, processors are used. Under the conditions of uniform load distribution, these results are shown to be asymptotically optimal. The schemes allow efficient use of up to O(n) processors before the total data traffic reaches the maximum value of O(n(sup 3/2)). The partitioning employed within the scheme, allows a better utilization of the data accessed from shared memory than those of previously published methods.
CE dual-homing protection in layer 1 VPN
NASA Astrophysics Data System (ADS)
Du, Shu; Peng, Yunfeng; Long, Keping
2008-11-01
Layer 1 VPN (L1VPN) extends the notion of VPN to the optical domain to provide virtually dedicated circuit like leased lines, so that the security is more enhanced. Despite their secure gains from channel isolation, VPNs still suffer fragilities resulting from link-failures or node-failures. Extensive activities on survivability designs for wavelength-routed optical networks are proposed, including various protection and restoration schemes, but concerns on network edge are rare. Dual-homing is an effective skill to achieve survivability gains for L1VPNs. There are two dual-homing mode: Active/Standby mode and Load-Sharing mode In this paper, we investigate the problem of PE assignment, which is the key of dual-homing design and is NP-hard. We formulate it as an integer programming problem, and propose heuristic solutions. Simulation results show that the proposed solutions work in a correct and effective way and the Load-Sharing mode has higher bandwidth efficiency than Active/Standby mode.
Visual short-term memory load strengthens selective attention.
Roper, Zachary J J; Vecera, Shaun P
2014-04-01
Perceptual load theory accounts for many attentional phenomena; however, its mechanism remains elusive because it invokes underspecified attentional resources. Recent dual-task evidence has revealed that a concurrent visual short-term memory (VSTM) load slows visual search and reduces contrast sensitivity, but it is unknown whether a VSTM load also constricts attention in a canonical perceptual load task. If attentional selection draws upon VSTM resources, then distraction effects-which measure attentional "spill-over"-will be reduced as competition for resources increases. Observers performed a low perceptual load flanker task during the delay period of a VSTM change detection task. We observed a reduction of the flanker effect in the perceptual load task as a function of increasing concurrent VSTM load. These findings were not due to perceptual-level interactions between the physical displays of the two tasks. Our findings suggest that perceptual representations of distractor stimuli compete with the maintenance of visual representations held in memory. We conclude that access to VSTM determines the degree of attentional selectivity; when VSTM is not completely taxed, it is more likely for task-irrelevant items to be consolidated and, consequently, affect responses. The "resources" hypothesized by load theory are at least partly mnemonic in nature, due to the strong correspondence they share with VSTM capacity.
DOE Office of Scientific and Technical Information (OSTI.GOV)
Keller, J.; Lacava, W.; Austin, J.
2015-02-01
This work investigates the minimum level of fidelity required to accurately simulate wind turbine gearboxes using state-of-the-art design tools. Excessive model fidelity including drivetrain complexity, gearbox complexity, excitation sources, and imperfections, significantly increases computational time, but may not provide a commensurate increase in the value of the results. Essential designparameters are evaluated, including the planetary load-sharing factor, gear tooth load distribution, and sun orbit motion. Based on the sensitivity study results, recommendations for the minimum model fidelities are provided.
Jani, Andrea J.; Briggs, Cheryl J.
2014-01-01
Symbiotic microbial communities may interact with infectious pathogens sharing a common host. The microbiome may limit pathogen infection or, conversely, an invading pathogen can disturb the microbiome. Documentation of such relationships during naturally occurring disease outbreaks is rare, and identifying causal links from field observations is difficult. This study documented the effects of an amphibian skin pathogen of global conservation concern [the chytrid fungus Batrachochytrium dendrobatidis (Bd)] on the skin-associated bacterial microbiome of the endangered frog, Rana sierrae, using a combination of population surveys and laboratory experiments. We examined covariation of pathogen infection and bacterial microbiome composition in wild frogs, demonstrating a strong and consistent correlation between Bd infection load and bacterial community composition in multiple R. sierrae populations. Despite the correlation between Bd infection load and bacterial community composition, we observed 100% mortality of postmetamorphic frogs during a Bd epizootic, suggesting that the relationship between Bd and bacterial communities was not linked to variation in resistance to mortal disease and that Bd infection altered bacterial communities. In a controlled experiment, Bd infection significantly altered the R. sierrae microbiome, demonstrating a causal relationship. The response of microbial communities to Bd infection was remarkably consistent: Several bacterial taxa showed the same response to Bd infection across multiple field populations and the laboratory experiment, indicating a somewhat predictable interaction between Bd and the microbiome. The laboratory experiment demonstrates that Bd infection causes changes to amphibian skin bacterial communities, whereas the laboratory and field results together strongly support Bd disturbance as a driver of bacterial community change during natural disease dynamics. PMID:25385615
InsightSTEM Campus Ambassadors: Worldwide Grassroots Student Networking, Development, and Outreach
NASA Astrophysics Data System (ADS)
Nuccitelli, D. A.
2016-12-01
We present results on our Campus Ambassadors program, which in three years has grown, through grassroots networking, to comprise over 550 members in over 30 countries worldwide. We will share our experiences of peer-to-peer network growth on an international scale, as well as issues with growth and program impacts in the USA, South America, Africa, Asia and Europe. InsightSTEM seeks to democratize STEM knowledge through exploration, and our Campus Ambassadors are supported in their desire to share their own STEM knowledge with their broader communities. They have impacts by supporting individuals becoming critically thinking, STEM literate, global learners. Since its inception in 2014, the program has relied on its members to continue to expand the program. The most notable impacts globally have been with students in India, and in West Africa (most notably Liberia). We will discuss the challenges and outcomes of providing a global program for these vastly diverse communities, and strategies we are testing to ensure an equitable experience for all participants.
InsightSTEM Campus Ambassadors: Worldwide Grassroots Student Networking, Development, and Outreach
NASA Astrophysics Data System (ADS)
Noel-Storr, J.
2017-12-01
We present results on our Campus Ambassadors program, which in three years has grown, through grassroots networking, to comprise over 550 members in over 30 countries worldwide. We will share our experiences of peer-to-peer network growth on an international scale, as well as issues with growth and program impacts in the USA, South America, Africa, Asia and Europe. InsightSTEM seeks to democratize STEM knowledge through exploration, and our Campus Ambassadors are supported in their desire to share their own STEM knowledge with their broader communities. They have impacts by supporting individuals becoming critically thinking, STEM literate, global learners. Since its inception in 2014, the program has relied on its members to continue to expand the program. The most notable impacts globally have been with students in India, and in West Africa (most notably Liberia). We will discuss the challenges and outcomes of providing a global program for these vastly diverse communities, and strategies we are testing to ensure an equitable experience for all participants.
Long-range transport of airborne microbes over the global tropical and subtropical ocean.
Mayol, Eva; Arrieta, Jesús M; Jiménez, Maria A; Martínez-Asensio, Adrián; Garcias-Bonet, Neus; Dachs, Jordi; González-Gaya, Belén; Royer, Sarah-J; Benítez-Barrios, Verónica M; Fraile-Nuez, Eugenio; Duarte, Carlos M
2017-08-04
The atmosphere plays a fundamental role in the transport of microbes across the planet but it is often neglected as a microbial habitat. Although the ocean represents two thirds of the Earth's surface, there is little information on the atmospheric microbial load over the open ocean. Here we provide a global estimate of microbial loads and air-sea exchanges over the tropical and subtropical oceans based on the data collected along the Malaspina 2010 Circumnavigation Expedition. Total loads of airborne prokaryotes and eukaryotes were estimated at 2.2 × 10 21 and 2.1 × 10 21 cells, respectively. Overall 33-68% of these microorganisms could be traced to a marine origin, being transported thousands of kilometres before re-entering the ocean. Moreover, our results show a substantial load of terrestrial microbes transported over the oceans, with abundances declining exponentially with distance from land and indicate that islands may act as stepping stones facilitating the transoceanic transport of terrestrial microbes.The extent to which the ocean acts as a sink and source of airborne particles to the atmosphere is unresolved. Here, the authors report high microbial loads over the tropical Atlantic, Pacific and Indian oceans and propose islands as stepping stones for the transoceanic transport of terrestrial microbes..
Quasi-static elastography comparison of hyaline cartilage structures
NASA Astrophysics Data System (ADS)
McCredie, A. J.; Stride, E.; Saffari, N.
2009-11-01
Joint cartilage, a load bearing structure in mammals, has only limited ability for regeneration after damage. For tissue engineers to design functional constructs, better understanding of the properties of healthy tissue is required. Joint cartilage is a specialised structure of hyaline cartilage; a poroviscoelastic solid containing fibril matrix reinforcements. Healthy joint cartilage is layered, which is thought to be important for correct tissue function. However, the behaviour of each layer during loading is poorly understood. Ultrasound elastography provides access to depth-dependent information in real-time for a sample during loading. A 15 MHz focussed transducer provided details from scatterers within a small fixed region in each sample. Quasi-static loading was applied to cartilage samples while ultrasonic signals before and during compressions were recorded. Ultrasonic signals were processed to provide time-shift profiles using a sum-squared difference method and cross-correlation. Two structures of hyaline cartilage have been tested ultrasonically and mechanically to determine method suitability for monitoring internal deformation differences under load and the effect of the layers on the global mechanical material behaviour. Results show differences in both the global mechanical properties and the ultrasonically tested strain distributions between the two structures tested. It was concluded that these differences are caused primarily by the fibril orientations.
Improving the Response of a Load Cell by Using Optimal Filtering
Hernandez, Wilmar
2006-01-01
Load cells are transducers used to measure force or weight. Despite the fact that there is a wide variety of load cells, most of these transducers that are used in the weighing industry are based on strain gauges. In this paper, an s-beam load cell based on strain gauges was suitably assembled to the mechanical structure of several seats of a bus under performance tests and used to measure the resistance of their mechanical structure to tension forces applied horizontally to the seats being tested. The load cell was buried in a broad-band noise background where the unwanted information and the relevant signal sometimes share a very similar frequency spectrum and its performance was improved by using a recursive least-squares (RLS) lattice algorithm. The experimental results are satisfactory and a significant improvement in the signal-to-noise ratio at the system output of 27 dB was achieved, which is a good performance factor for judging the quality of the system.
NASA Technical Reports Server (NTRS)
Nagano, Hosei; Ku, Jentung
2006-01-01
Thermal performance of a miniature loop heat pipe (MLHP) with two evaporators and two condensers is described. A comprehensive test program, including start-up, high power, low power, power cycle, and sink temperature cycle tests, has been executed at NASA Goddard Space Flight Center for potential space applications. Experimental data showed that the loop could start with heat loads as low as 2W. The loop operated stably with even and uneven evaporator heat loads, and even and uneven condenser sink temperatures. Heat load sharing between the two evaporators was also successfully demonstrated. The loop had a heat transport capability of l00W to 120W, and could recover from a dry-out by reducing the heat load to evaporators. Low power test results showed the loop could work stably for heat loads as low as 1 W to each evaporator. Excellent adaptability of the MLHP to rapid changes of evaporator power and sink temperature were also demonstrated.
NASA Technical Reports Server (NTRS)
Holland, D. B.; Virgin, L. N.; Belvin, W. K.
2003-01-01
This paper presents a parameter study of the effect of boom axial loading on the global dynamics of a 2-meter solar sail scale model. The experimental model used is meant for building expertise in finite element analysis and experimental execution, not as a predecessor to any planned flight mission or particular design concept. The results here are to demonstrate the ability to predict and measure structural dynamics and mode shapes in the presence of axial loading.
ComprehensiveBench: a Benchmark for the Extensive Evaluation of Global Scheduling Algorithms
NASA Astrophysics Data System (ADS)
Pilla, Laércio L.; Bozzetti, Tiago C.; Castro, Márcio; Navaux, Philippe O. A.; Méhaut, Jean-François
2015-10-01
Parallel applications that present tasks with imbalanced loads or complex communication behavior usually do not exploit the underlying resources of parallel platforms to their full potential. In order to mitigate this issue, global scheduling algorithms are employed. As finding the optimal task distribution is an NP-Hard problem, identifying the most suitable algorithm for a specific scenario and comparing algorithms are not trivial tasks. In this context, this paper presents ComprehensiveBench, a benchmark for global scheduling algorithms that enables the variation of a vast range of parameters that affect performance. ComprehensiveBench can be used to assist in the development and evaluation of new scheduling algorithms, to help choose a specific algorithm for an arbitrary application, to emulate other applications, and to enable statistical tests. We illustrate its use in this paper with an evaluation of Charm++ periodic load balancers that stresses their characteristics.
Significant radiative impact of volcanic aerosol in the lowermost stratosphere
Andersson, Sandra M.; Martinsson, Bengt G.; Vernier, Jean-Paul; Friberg, Johan; Brenninkmeijer, Carl A. M.; Hermann, Markus; van Velthoven, Peter F. J.; Zahn, Andreas
2015-01-01
Despite their potential to slow global warming, until recently, the radiative forcing associated with volcanic aerosols in the lowermost stratosphere (LMS) had not been considered. Here we study volcanic aerosol changes in the stratosphere using lidar measurements from the NASA CALIPSO satellite and aircraft measurements from the IAGOS-CARIBIC observatory. Between 2008 and 2012 volcanism frequently affected the Northern Hemisphere stratosphere aerosol loadings, whereas the Southern Hemisphere generally had loadings close to background conditions. We show that half of the global stratospheric aerosol optical depth following the Kasatochi, Sarychev and Nabro eruptions is attributable to LMS aerosol. On average, 30% of the global stratospheric aerosol optical depth originated in the LMS during the period 2008–2011. On the basis of the two independent, high-resolution measurement methods, we show that the LMS makes an important contribution to the overall volcanic forcing. PMID:26158244
Constraints on Transient Viscoelastic Rheology of the Asthenosphere From Seasonal Deformation
NASA Astrophysics Data System (ADS)
Chanard, Kristel; Fleitout, Luce; Calais, Eric; Barbot, Sylvain; Avouac, Jean-Philippe
2018-03-01
We discuss the constraints on short-term asthenospheric viscosity provided by seasonal deformation of the Earth. We use data from 195 globally distributed continuous Global Navigation Satellite System stations. Surface loading is derived from the Gravity Recovery and Climate Experiment and used as an input to predict geodetic displacements. We compute Green's functions for surface displacements for a purely elastic spherical reference Earth model and for viscoelastic Earth models. We show that a range of transient viscoelastic rheologies derived to explain the early phase of postseismic deformation may induce a detectable effect on the phase and amplitude of horizontal displacements induced by seasonal loading at long wavelengths (1,300-4,000 km). By comparing predicted and observed seasonal horizontal motion, we conclude that transient asthenospheric viscosity cannot be lower than 5 × 1017 Pa.s, suggesting that low values of transient asthenospheric viscosities reported in some postseismic studies cannot hold for the seasonal deformation global average.
Kulduk, Ahmet; Altun, Necdet S; Senkoylu, Alpaslan
2015-12-01
The primary purpose of dynamic stabilization is to preserve the normal range of motion (ROM) by restricting abnormal movement in the spine. Our aim was to analyze the effects of two different dynamic stabilization systems using finite element modeling (FEM). Coflex and Dynesys dynamic devices were modeled and implanted at the L4-L5 segment using virtual FEM. A 400 N compressive force combined with 6 N flexion, extension, bending and axial rotation forces was applied to the L3-4 and L4-5 segments. ROM and disc loading forces were analyzed. Both systems reduced ROM and disc loading forces at the implanted lumbar segment, with the exception of the Coflex interspinous device, which increased ROM by 19% and did not change disc-loading forces in flexion. The Coflex device prevented excessive disc loading, but increased ROM abnormally in flexion. Neither device provided satisfactory motion preservation or load sharing in other directions. Copyright © 2015 John Wiley & Sons, Ltd.